WorldWideScience

Sample records for olkiluoto site finland

  1. Groundwater flow modelling at the Olkiluoto site, Finland

    International Nuclear Information System (INIS)

    Loefman, J.

    1996-01-01

    Preliminary site investigations for spent fuel disposal has been carried out at the Olkiluoto site, Finland. During the investigations high salt concentrations were measured in the groundwater samples deep in the bedrock. In this study, the groundwater flow is analyzed at Olkiluoto taking into account the effects of salinity. The transient simulations are performed by solving coupled and non-linear partial differential equations describing the flow and solute transport. A site-specific simulation model for flow and transport is developed on the basis of the field investigations. The simulations are carried out for a period that started when the highest hills at Olkiluoto rose above sea level. The simulation period continues until the present day. The results of the coupled simulations were strongly dependent on the poorly known initial salinity distribution in the solution domain. The DP approximation together with the EC approximation proved to be a useful complementary approach when simulating solute transport in a fractured rock mass. The simulations also confirm the assumption that the realistic simulation of groundwater flow at Olkiluoto requires taking into account the effects of salinity

  2. Geological ductile deformation mapping at the Olkiluoto site, Eurajoki, Finland

    Energy Technology Data Exchange (ETDEWEB)

    Engstroem, J. [Geological Survey of Finland, Espoo (Finland)

    2013-12-15

    During 2010-2012 eight larger excavated and cleaned outcrops were investigated to study the polyphase nature of the ductile deformation within the Olkiluoto Island. A detailed structural geological mapping together with a thin section study was performed to get a broader and better understanding of the nature and occurrence of these different ductile deformation phases. These outcrops were selected to represent all different ductile deformation phases recognized earlier during the site investigations. The relicts of primary sedimentary structures and products of the earliest deformations (D{sub 0}-D{sub 1}) are mostly obscured by later deformation events. The D{sub 2}-D{sub 4} is the most significant ductile deformation phases occurring on the Olkiluoto Island and almost all structural features can be labeled within these three phases. The outcrops for this investigation were selected mostly from the eastern part of the Olkiluoto Island because that part of the Island has been less investigated previously. As a reference, one outcrop was selected in the western part of the Island where it was previously known that this location had especially well preserved structures of the second deformation phase (D{sub 2}). The S{sub 2} foliation is E-W orientated with moderate dip towards south. A few folds can be associated with this deformational event, mostly having a tight to isoclinal character. During D{sub 3} the migmatites were re-deformed and migrated leucosomes, were intruded mainly parallel to S{sub 3} axial surfaces having a NE-SW orientation. Generally the dip of the S{sub 3} axial surfaces is slightly more steeper (55- 65 deg C) than that of the S{sub 2} axial surfaces, which shows a more moderate dip (40-65 deg C). F{sub 3} fold structures are quite common in the eastern part of Island showing asymmetrical, overturned, shear folds usually with a dextral sense of shear. Large scale D{sub 3} shear structures contain blastomylonites as characteristic fault rocks

  3. An isotopic and fluid inclusion study of fracture calcite from borehole OL-KR1 at the Olkiluoto site, Finland

    International Nuclear Information System (INIS)

    Blyth, A.; Frape, S.; Blomqvist, R.; Nissinen, P.; McNutt, R.

    1998-04-01

    A study of the geochemistry of fracture filling calcite in borehole OL-KR1 at the radioactive waste disposal investigation site Olkiluoto (in Finland) was undertaken in 1998. The purpose of the present study is to characterize the fracture calcite using mineralogy, oxygen, carbon and strontium isotopes, and fluid inclusions in order to determine past and present chemical and isotopic condition at the site

  4. An isotopic and fluid inclusion study of fracture calcite from borehole OL-KR1 at the Olkiluoto site, Finland

    Energy Technology Data Exchange (ETDEWEB)

    Blyth, A.; Frape, S. [Univ. of Waterloo, ON (Canada); Blomqvist, R.; Nissinen, P. [Geological Survey of Finland, Espoo (Finland); McNutt, R. [McMaster Univ. of Hamilton, ON (Canada)

    1998-04-01

    A study of the geochemistry of fracture filling calcite in borehole OL-KR1 at the radioactive waste disposal investigation site Olkiluoto (in Finland) was undertaken in 1998. The purpose of the present study is to characterize the fracture calcite using mineralogy, oxygen, carbon and strontium isotopes, and fluid inclusions in order to determine past and present chemical and isotopic condition at the site 39 refs.

  5. Geological discrete-fracture network model (version 1) for the Olkiluoto site, Finland

    International Nuclear Information System (INIS)

    Fox, A.; Buoro, A.; Dahlbo, K.; Wiren, L.

    2009-10-01

    This report describes the methods, analyses, and conclusions of the modelling team in the production of a discrete-fracture network (DFN) model for the Olkiluoto Site in Finland. The geological DFN is a statistical model for stochastically simulating rock fractures and minor faults at a scale ranging from approximately 0.05 m to approximately 500 m; an upper scale limit is not expressly defined, but the DFN model explicitly excludes structures at deformation-zone scales (∼ 500 m) and larger. The DFN model is presented as a series of tables summarizing probability distributions for several parameters necessary for fracture modelling: fracture orientation, fracture size, fracture intensity, and associated spatial constraints. The geological DFN is built from data collected during site characterization (SC) activities at Olkiluoto, which is currently planned to function as a final deep geological repository for spent fuel and nuclear waste from the Finnish nuclear power program. Data used in the DFN analyses include fracture maps from surface outcrops and trenches (as of July 2007), geological and structural data from cored boreholes (as of July 2007), and fracture information collected during the construction of the main tunnels and shafts at the ONKALO laboratory (January 2008). The modelling results suggest that the rock volume at Olkiluoto surrounding the ONKALO tunnel can be separated into three distinct volumes (fracture domains): an upper block, an intermediate block, and a lower block. The three fracture domains are bounded horizontally and vertically by large deformation zones. Fracture properties, such as fracture orientation and relative orientation set intensity, vary between fracture domains. The rock volume at Olkiluoto is dominated by three distinct fracture sets: subhorizontally-dipping fractures striking north-northeast and dipping to the east, a subvertically-dipping fracture set striking roughly north-south, and a subverticallydipping fracture set

  6. Geological discrete fracture network model for the Olkiluoto site, Eurajoki, Finland. Version 2.0

    International Nuclear Information System (INIS)

    Fox, A.; Forchhammer, K.; Pettersson, A.; La Pointe, P.; Lim, D-H.

    2012-06-01

    This report describes the methods, analyses, and conclusions of the modeling team in the production of the 2010 revision to the geological discrete fracture network (DFN) model for the Olkiluoto Site in Finland. The geological DFN is a statistical model for stochastically simulating rock fractures and minor faults at a scale ranging from approximately 0.05 m to approximately 565m; deformation zones are expressly excluded from the DFN model. The DFN model is presented as a series of tables summarizing probability distributions for several parameters necessary for fracture modeling: fracture orientation, fracture size, fracture intensity, and associated spatial constraints. The geological DFN is built from data collected during site characterization (SC) activities at Olkiluoto, which is selected to function as a final deep geological repository for spent fuel and nuclear waste from the Finnish nuclear power program. Data used in the DFN analyses include fracture maps from surface outcrops and trenches, geological and structural data from cored drillholes, and fracture information collected during the construction of the main tunnels and shafts at the ONKALO laboratory. Unlike the initial geological DFN, which was focused on the vicinity of the ONKALO tunnel, the 2010 revisions present a model parameterization for the entire island. Fracture domains are based on the tectonic subdivisions at the site (northern, central, and southern tectonic units) presented in the Geological Site Model (GSM), and are further subdivided along the intersection of major brittle-ductile zones. The rock volume at Olkiluoto is dominated by three distinct fracture sets: subhorizontally-dipping fractures striking north-northeast and dipping to the east that is subparallel to the mean bedrock foliation direction, a subvertically-dipping fracture set striking roughly north-south, and a subvertically-dipping fracture set striking approximately east-west. The subhorizontally-dipping fractures

  7. Geological discrete fracture network model for the Olkiluoto site, Eurajoki, Finland. Version 2.0

    Energy Technology Data Exchange (ETDEWEB)

    Fox, A.; Forchhammer, K.; Pettersson, A. [Golder Associates AB, Stockholm (Sweden); La Pointe, P.; Lim, D-H. [Golder Associates Inc. (Finland)

    2012-06-15

    This report describes the methods, analyses, and conclusions of the modeling team in the production of the 2010 revision to the geological discrete fracture network (DFN) model for the Olkiluoto Site in Finland. The geological DFN is a statistical model for stochastically simulating rock fractures and minor faults at a scale ranging from approximately 0.05 m to approximately 565m; deformation zones are expressly excluded from the DFN model. The DFN model is presented as a series of tables summarizing probability distributions for several parameters necessary for fracture modeling: fracture orientation, fracture size, fracture intensity, and associated spatial constraints. The geological DFN is built from data collected during site characterization (SC) activities at Olkiluoto, which is selected to function as a final deep geological repository for spent fuel and nuclear waste from the Finnish nuclear power program. Data used in the DFN analyses include fracture maps from surface outcrops and trenches, geological and structural data from cored drillholes, and fracture information collected during the construction of the main tunnels and shafts at the ONKALO laboratory. Unlike the initial geological DFN, which was focused on the vicinity of the ONKALO tunnel, the 2010 revisions present a model parameterization for the entire island. Fracture domains are based on the tectonic subdivisions at the site (northern, central, and southern tectonic units) presented in the Geological Site Model (GSM), and are further subdivided along the intersection of major brittle-ductile zones. The rock volume at Olkiluoto is dominated by three distinct fracture sets: subhorizontally-dipping fractures striking north-northeast and dipping to the east that is subparallel to the mean bedrock foliation direction, a subvertically-dipping fracture set striking roughly north-south, and a subvertically-dipping fracture set striking approximately east-west. The subhorizontally-dipping fractures

  8. Distribution coefficients of different soil types at Olkiluoto repository site and its surroundings, southwestern Finland

    Energy Technology Data Exchange (ETDEWEB)

    Lahdenperae, Anne-Maj [Saanio and Riekkola Oy, Laulukuja 4, FI-00420 Helsinki (Finland); Ikonen, Ari T.K. [Environmental Research and Assessment EnviroCase, Ltd., Hallituskatu 1 D 4, 28100 Pori (Finland)

    2014-07-01

    In Finland, the Olkiluoto Island on the western coast has been selected as a repository site for the spent nuclear fuel. Due to shallow sea areas around the island, the post-glacial crustal rebound (around 6 mm/y) is changing the landscape significantly; during the next thousands of years new soil types are emerging, the present bays will narrow and form future lakes and mires assumedly similar to those farther inland at present. The effects of terrain development are important in long-term safety assessments for the repository, especially in the biosphere assessments addressing radiation exposure of people and biota in scenarios of radionuclide releases. 'In situ' distribution coefficients, K{sub d} values are used to indicate the relevant mobility of radionuclides of concern from nuclear waste. These radionuclides have very long half-lives and long interaction times with soils, ranging from centuries to millennia. By measuring the desorption K{sub d} values of the indigenous stable elements (Ag, Cl, Cs, I, Mo, Nb, Ni, Se and Sr) from field moist samples are a valid description of slow retention processes. The 'in situ' K{sub d} desorption values are calculated for humus, peat and different mineral soil samples taken from the Olkiluoto Island and the Reference Area used as an analogue of the future terrain. The solids are extracted alternatively by HNO{sub 3}-HF and NH{sub 4}Ac (pH 4.5). The K{sub d} values are highly dependent on environmental factors, including but not limited to pH, soil type, soil horizon, soil body, texture, element chemical form, organic matter, carbon content and biological activity. This is discussed in the contribution; e.g., for several elements pH and K{sub d} values correlate - the finer the soil or sediment, the higher the K{sub d} values - and humus and peat samples have a clear correlation with the organic matter and carbon contents. The contribution also compares the 'in situ' K{sub d} values to

  9. Geological setting of the Olkiluoto investigation site, Eurajoki, SW Finland. Excursion guidebook

    International Nuclear Information System (INIS)

    Paulamaeki, S.

    2009-08-01

    -1250 million years in age. Their geochemical features suggest that they are feeder channels to continental flood basalts, which have not, however, been preserved in the Satakunta area. Lake Saeaeksjaervi, northeast of the Satakunta sandstone, hosts approximately 4.5 km wide impact structure of early Cambrian age (ca. 560 Ma). Below water level it contains unexposed suevite breccia and impact melt breccia. Day 1 of the field excursion introduces the Palaeoproterozoic geology of the Olkiluoto site, with special emphasis to the structural geology. Day 2 presents the Mesoproterozoic history of southern Satakunta area, including the Laitila and Eurajoki rapakivi granites, the Satakunta sandstone and the olivine diabases. The excursion ends to the Lake Saeaeksjaervi, where boulders of impact rocks can be found on the northern shore of the lake. (orig.)

  10. Challenges and Solutions for the Integration of Structural and Hydrogeological Understanding of Fracture Systems - Insights from the Olkiluoto Site, Finland

    Science.gov (United States)

    Hartley, L. J.; Aaltonen, I.; Baxter, S. J.; Cottrell, M.; Fox, A. L.; Hoek, J.; Koskinen, L.; Mattila, J.; Mosley, K.; Selroos, J. O.; Suikkanen, J.; Vanhanarkaus, O.; Williams, T. R. N.

    2017-12-01

    A field site at Olkiluoto in SW Finland has undergone extensive investigations as a location for a deep geological repository for spent nuclear fuel, which is expected to become operational in the early 2020s. Characterisation data comes from 58 deep cored drillholes, a wide variety of geophysical investigations, many outcrops, kilometres of underground mapping and testing in the ONKALO research facility, and groundwater pressure monitoring and sampling in both deep and shallow holes. A primary focus is on the properties of natural fractures and brittle fault zones in the low permeability crystalline rocks at Olkiluoto; an understanding of the flow and transport processes in these features are an essential part of assessing long-term safety of the repository. This presentation will illustrate how different types of source data and cross-disciplinary interpretations are integrated to develop conceptual and numerical models of the fracture system. A model of the brittle fault zones developed from geological and geophysical data provides the hydrostructural backbone controlling the most intense fracturing and dynamic conduits for fluids. Models of ductile deformation and lithology form a tectonic framework for the description of fracture heterogeneity in the background rock, revealing correlations between the intensity and orientation of fractures with geological and spatial properties. The sizes of brittle features are found to be best defined on two scales relating to individual fractures and zones. Inferred fracture-specific from flow logging are correlated with fracture geometric and mechanical properties along with in situ stress measurements to create a hydromechanical description of fracture hydraulic properties. The insights and understandings gained from these efforts help define a discrete fracture network (DFN) model for the Olkiluoto site, with hydrogeological characteristics consistent with monitoring data of hydraulic heads and their disturbances to

  11. Olkiluoto site description 2011

    International Nuclear Information System (INIS)

    2012-12-01

    This fourth version of the Olkiluoto Site Report, produced by the OMTF (Olkiluoto Modelling Task Force), updates the Olkiluoto Site Report 2008 with the data and knowledge obtained up to December 2010. A descriptive model of the site (the Site Descriptive Model, SDM), i.e. a model describing the geological and hydrogeological structure of the site, properties of the bedrock and the groundwater and its flow, and the associated interacting processes and mechanisms. The SDM is divided into six parts: surface system, geology, rock mechanics, hydrogeology, hydrogeochemistry and transport properties

  12. Olkiluoto site description 2011

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-12-15

    This fourth version of the Olkiluoto Site Report, produced by the OMTF (Olkiluoto Modelling Task Force), updates the Olkiluoto Site Report 2008 with the data and knowledge obtained up to December 2010. A descriptive model of the site (the Site Descriptive Model, SDM), i.e. a model describing the geological and hydrogeological structure of the site, properties of the bedrock and the groundwater and its flow, and the associated interacting processes and mechanisms. The SDM is divided into six parts: surface system, geology, rock mechanics, hydrogeology, hydrogeochemistry and transport properties.

  13. Comparison of site descriptive models for Olkiluoto, Finland and Forsmark, Sweden

    Energy Technology Data Exchange (ETDEWEB)

    Geier, J.; Bath, A.; Stephansson, O.; Luukkonen, A.

    2012-08-15

    The proposed high-level radioactive waste repository sites at Olkiluoto and Forsmark share broadly similar geologic histories and regional settings. Despite differences in lithology, rock strength and patterns of brittle deformation, the sites show similarities in terms of hydrogeochemistry and hydrogeology. These similarities reflect a dominating influence of saline and brackish water intrusion during inundation by the postglacial Littorina Sea and Baltic Sea, followed by exposure to meteoric waters following postglacial uplift and transition to a Baltic coastal setting. Both sites also contain deep bedrock saline groundwater, though this is more evident at Olkiluoto than at Forsmark. A comparative study of site descriptive models for the two sites identifies the following key differences that could potentially impact safety of a repository: (1) Redox controls, buffering and biogeochemistry at proposed repository depths; (2) Salinity gradients at and below proposed repository depths; (3) Methane concentrations at and below proposed repository depths; (4) Depths to which glacial water and Littorina water penetrated; (5) Cation hydrogeochemistry and water-rock reaction; (6) Pore water compositions in rock matrix; (7) Rock fabric, secondary minerals and alteration with respect to radionuclide retention; (8) Brittle deformation fabric differences on multiple scales that affect vertical hydraulic conductivity; (9) Differences in apparent frequency of encountering water-conducting networks at proposed repository depths; (10) Shallow bedrock hydraulic properties; (11) Unique intrusive or dissolution features; (12) Connectivity of site-scale models to regional-scale features; (13) Mesoproterozoic rocks in vicinity and possibilities for human-intrusion scenarios; (14) Rock stresses and bedrock strength and deformability at proposed repository depths; (15) Thermal anisotropy. These differences are all potentially significant to safety functions, but none are so severe that

  14. Modelling of the in situ stress state at Olkiluoto Site, Western Finland

    International Nuclear Information System (INIS)

    Valli, J.; Kuula, H.; Hakala, M.

    2011-06-01

    In order to determine the interaction of in situ stress and geological features at Olkiluoto with the ONKALO area under more specific focus, stress modelling work was launched in 2009. This entailed updating a previously used model geometry to suit current needs whilst also updating interpreted brittle deformation zones according to the data provided by Posiva in the beginning of 2010. The previous model geometry was originally used for seismic and glacial load simulations. Brittle deformation zones were updated in the model according to a new selection criterion which added a number of brittle deformation zones. Changes in the geometry of certain brittle deformation zones were also necessary to better fit the early 2010 interpretations from Posiva. Modelling goals were to clarify the effect of joint parameters on stress magnitude and orientation and which of the major brittle deformation zones detected in the ONKALO region could have potential effects on local in situ stress states. Additional goals included modelling the effect of several optional thrust boundary conditions and an ice-age. Compression from the northwest-southeast was used as the default approach whilst north-south, east-west and northeast-southwest were optional conditions. A simplified glaciation cycle was also simulated. Results were clear in demonstrating the critical effect of joint cohesion and joint friction angle, i.e. shear strength, on stress-geology interaction, essentially in this order of importance. The case that utilised both drillhole core-logging and ONKALO tunnel mapping results did not exhibit much if any stress-geology interactions as BFZ strength parameters were too high in order to allow any interactions to occur. The geometry and orientation of brittle deformation zones was found to be of significant importance; deformation zones with a shallow dip roughly in the direction of applied compression were optimal for causing stress rotations and the increase of stress magnitude

  15. Geological mapping of investigation trench OL-TK14 at the Olkiluoto study site, Eurajoki, SW Finland

    International Nuclear Information System (INIS)

    Nordbaeck, N.

    2007-12-01

    Geological mapping of investigation trench OL-TK14 was carried out by the Geological Survey of Finland at the Olkiluoto study site, Eurajoki, as part of Posiva Oy's site investigation programme for the development of an underground repository for nuclear waste. The E-W striking, ca. 215 m long trench is located in the eastern part of the Olkiluoto Island adjacent to boreholes OL-KR40 and OL-KR45. The trench was cleaned with a pressure washer and pressurized air. The rock types were determined macroscopically. Five samples were also investigated microscopically. The main rock type in the trench is veined gneiss. A few less than 0.5 m wide coarsegrained pegmatitic granite dykes are also encountered. Furthermore a large number of mica gneiss, quartz gneiss and skarn inclusions are present in the veined gneiss, being often elongated and parallel to the foliation. The most dominant tectonic feature is the foliation S2 and associated intense granitic leucosome veining. The foliation strikes ENE-WSW and dips steeply towards SES. Intensely to moderately banded rocks dominate the trench. The sparse F3 folds observed in OL-TK14 are small-scale tight folds in leucosome veins. A large-scale (10 m) open bending of the foliation that could be a result of D4 folding was also observed. Shearbands and other signs of ductile shearing were observed on many locations in the trench and in the eastern part there is a high-grade ductile shear zone intersection. During the fracture mapping, all fractures intersecting the central thread were investigated and a total of 684 fractures were recorded. The average fracture density of the trench is 3.18 fractures/m. On the basis of fracture orientations three main sets can be distinguished: 1) a set striking N-S with vertical dip, 2) a ENE-WSW striking set with varying dips towards the SSE (parallel to the foliation) and 3) a NE-SW striking set with sub-vertical dip towards the SE or the NW. Most of the measured fractures are short due to the

  16. Geological mapping of investigation trench OL-TK18 at the Olkiluoto study site, Eurajoki, SW Finland

    Energy Technology Data Exchange (ETDEWEB)

    Engstroem, J. [GTK Geological Survey of Finland, Espoo (Finland)

    2012-04-15

    Survey of Finland at the Olkiluoto study site, Eurajoki, as part of Posiva Oy's site investigation programme for the development of an underground repository for nuclear waste. The E-W striking, ca. 55 m long trench is located in the central part of the Olkiluoto Island adjacent to investigation trenches OL-TK12 and OL-TK4. The trench was cleaned with a pressure washer and pressurized air. The rock types were determined macroscopically. The rock types in investigation trench OL-TK18 is of heterogeneous character, with a large variation in their composition. The rocks vary from tonalitic-granodioritic gneiss to diatexitic gneiss, with portions of K-feldspar porphyritic gneiss. Inclusions of mica gneiss and a well-preserved schollen migmatite is encountered. The trench ends in a feldspar-rich pegmatoid. The most dominant tectonic feature is D{sub 4} ductile deformation domain and associated S{sub 4} foliation. This domain and hence the S{sub 4} foliation is striking NE-SW with a moderate dip towards SE. Both ends of the trench are dominated by the earlier deformation phase, showing S{sub 3} foliation striking ENE-WSW and roughly dipping towards the S. The S{sub 3} foliation is associated with small-scaled granitic leucosome veining, while the S{sub 4} foliation have a schistose character and it is more sheared. D{sub 4} ductile deformation domain is also characterised by a sheared blastomylonitic rock having growth of roundish feldspar porphyroblasts and BTschlierens indicating high alteration of the protolith. During the fracture mapping, all fractures intersecting the central thread were investigated and a total of 117 fractures were recorded. The average fracture frequency of the trench is 2.11 fractures/m. On the basis of fracture orientations one main set can be distinguished striking NE-SW (foliation parallel) with a moderate dip towards the SE. The median fracture trace length is 1.6 m and over half of the fractures exceed 1.5 m trace length, the longest

  17. Geological mapping of investigation trench OL-TK19 at the Olkiluoto study site, Eurajoki, SW Finland

    Energy Technology Data Exchange (ETDEWEB)

    Eroma, E.; Nordbaeck, N.; Engstroem, J. [Geological Survey of Finland, Espoo (Finland)

    2014-12-15

    In October 2012, the geological mapping of investigation trench OL-TK19 was carried out by the Geological Survey of Finland at the Olkiluoto study site. The SE-NW trending, ca. 85 m long trench is located in the central part of the Olkiluoto Island next to investigation trenches OL-TK18 and OL-TK4. The lithology in investigation trench OL-TK19 is of heterogeneous character, with rock type varying from veined gneiss, diatexitic gneiss to pegmatitic granite, along with portions of mica gneiss and K-feldspar porphyritic gneiss. In addition, inclusions of mica gneiss, quartz gneiss and skarn are encountered. The rocks have been subjected to a multiphase ductile deformation and the trench is situated in an area where the latest ductile deformation phase, D4 prevails. The investigation trench can be divided into three domains according to its dominant deformation phase and foliation; the eastern part of the trench is dominated by the D3 deformation phase whereas the middle and western parts are dominated by the D4 deformation phase. The S3 foliation has a more ENE-WSW oriented direction whereas the S4 is trending NE-SW. In addition to this difference in orientation, the different structural signature of these two deformation types is observed, the S3 foliation is defined by smaller scaled granitic leucosome veining whereas the S4 foliation is intensely sheared and have a schistose character. During the fracture mapping, all fractures intersecting the central thread were investigated and a total of 132 fractures were recorded. The average fracture frequency 1.53 fractures/m. On the basis of fracture orientations, three fracture sets can be defined. The first set is vertical and NW-SE trending, second set strikes NE-SW with a moderate dip towards the SE and the third set is vertical and NE-SW trending. The median fracture length is 1.38 m and most fractures do not exceed 0.5 m in length, the longest measured fracture being 5.30 m in length. Fracture fillings are mostly

  18. Geological mapping of investigation trench OL-TK9 at the Olkiluoto study site, Eurajoki, SW Finland

    International Nuclear Information System (INIS)

    Nordbaeck, N.; Talikka, M.

    2006-07-01

    Geological mapping of trench OL-TK9 was carried out the by the Geological Survey of Finland at the Olkiluoto study site, Eurajoki, southwestern Finland, as a part of Posiva Oy's site investigation programme for the development of an underground repository for nuclear waste. The NW-SE striking trench, which is about 371 metres in length and 0.4-2.5 metres in width, is situated to the west from the OL-TK3 in the northwestern part of the study site. The rock types were determined macroscopically and the main rock types were further investigated microscopically. On the basis of the migmatite structure, the migmatitic gneisses at Olkiluoto can be divided into three groups: veined gneiss, stromatic gneiss and diatexitic gneiss. Most of the migmatitic gneisses in the trench are veined gneisses and only a few short sections of the diatexitic gneiss or K-feldspar porphyry exist. Stromatic gneisses were not encountered. The leucosome of the veined gneiss show vein like, more or less linear traces with some features similar to large-scale augen structures, whereas the migmatitic structure of the diatexitic gneiss is more asymmetric and irregular. The southernmost part of the trench is dominated by mica gneiss and pegmatitic granite. The mica gneiss is homogenous mica-rich rock that contains less than 10 % granite leucosome material. The pegmatitic granite shows variations in grain size, colour, and mode of occurrence. The veined gneiss dominates the central part of the trench. The northernmost part of the trench is mainly comprised of tonalitic-granodioritic-granitic gneiss, which has an igneous character. Most rocks in the trench are altered, the intensity of the alteration varies from weak to strong, and the most common alteration type is chloritisation. The intense alteration has resulted in pervasive softening and weathering of the bedrock in places and up to four meters thick layers of strongly weathered rocks were observed on the edges of the trench. The foliation S2B

  19. Geological mapping of investigation Trench OL-TK13 at the Olkiluoto study site, Eurajoki, SW Finland

    International Nuclear Information System (INIS)

    Talikka, M.

    2007-04-01

    Geological mapping of investigation trench OL-TK13 was carried out by the Geological Survey of Finland at the Olkiluoto study site, Eurajoki, as a part Posiva Oy's site investigation programme for the development of an underground repository for nuclear waste. The east-west striking, ca. 250 m long trench is located in the vicinity of boreholes OL-KR23 and OL-KR27, ca. 250 m east of the ONKALO research facility. The mapping was performed from washed bedrock surface and rock types were determined macroscopically. The main rock types in OL-TK13 are diatexitic gneiss, veined gneiss, pegmatitic granite and K-feldspar porphyry. Mica gneiss and granite/granitized mica gneiss exist to a lesser extent. The diatexitic gneiss is the dominant rock type in the western part and the veined gneiss in the eastern part of the trench. The veined gneiss consists of pelitic mica gneiss paleosome and pegmatitic granite leucosome veins that are parallel to the foliation. In the diatexitic gneiss, the proportion of the leucosome veins and patches is over 50 % and the rock has an ambiguous texture. The pegmatitic granite also occurs as wider sections in the western part of the trench. The K-feldspar porphyry is characterized by potassium feldspar phenocrysts (diameter 4 deformation phase. The migmatitic gneisses were folded during the D 3 deformation phase resulting in small scale, tight and asymmetrical F 3 folds plunging moderately to the NE. During the fracture mapping, all fractures longer than one metre and all fractures intersecting the central thread were investigated. Measurements including orientation, length, fillings, Jr-value, Ja-value and undulation were recorded for a total of 860 fractures. The mean fracture density is 3.5 fracture/m. From the orientation data, three fracture sets were identified: (1) fractures parallel to the foliation, (2) subvertical N-S trending factures and (3) fractures dipping steeply to the N. ∼45 % of all fractures are 0.5-1.5 m in length and

  20. Geophysical investigations in the Olkiluoto area, Finland

    International Nuclear Information System (INIS)

    Heikkinen, E.; Paananen, M.

    1992-12-01

    Investigations were carried out at the Olkiluoto site at Eurajoki using geological, geophysical, geohydrological and geochemical methods in 1987-1992 to determine the suitability of the bedrock for the final disposal of spent nuclear fuel. In this survey airborne, ground and borehole geophysical methods were used to study the rock type distribution, fracturing and hydraulic conductivity of the bedrock to a depth of one kilometre

  1. EPR becomes reality at Finland's Olkiluoto 3

    International Nuclear Information System (INIS)

    Gueldner, R.; Giese, U.

    2005-01-01

    The EPR is a third-generation pressurized water reactor (PWR). Its development was started in 1992 by Framatome and Siemens within a Franco-German partnership. Since 2001 this work has been continued by Framatome ANP, which was formed when the two companies merged their nuclear businesses. The French company AREVA, world market leader in nuclear technology, holds a 66% share in Framatome ANP, with Siemens owning 34%. From the very start, development of the EPR was focused on improving plant safety and economics even further. The new reactor development was jointly financed together with the leading power utilities of both countries. The first steps towards realization of an EPR nuclear power plant were taken at Olkiluoto, Finland in 2004, consisting of initial preparation of the construction site. By mid-February 2005 the local municipality - Eurajoki - had issued a construction permit, and the Finnish Government a construction license pursuant to the Finnish Nuclear Energy Act. This had been preceded by a preliminary safety assessment prepared by the Finnish Radiation and Nuclear Safety Authority (STUK) for the Finnish Ministry of Trade and Industry in which STUK verified that it did not see any safety-related issues opposing issuance of the nuclear construction license. STUK emphasized that the evolutionary design of the EPR had been further improved by AREVA compared to the previous product lines. Concreting work began this spring and the unit will start commercial operation in 2009. Construction of an EPR has also been given the political go-ahead in France. According to the utility Electricite de France (EDF) the new reactor will be built as a forerunner of a later series at the site of Flamanville in Normandy. Construction is scheduled to begin in 2007. An EPR nuclear power plant has a rated electric capacity of around 1600 MW, depending on specific site conditions. Being the product of intense bilateral cooperation the EPR combines the technological

  2. Olkiluoto site description 2006

    International Nuclear Information System (INIS)

    Andersson, J.; Ahokas, H.; Hudson, J.A.

    2007-03-01

    This second version of the Olkiluoto Site Report, produced by the OMTF (Olkiluoto Modelling Task Force), updates the Olkiluoto Site Report 2004 (Posiva 2005) with the data and knowledge obtained up to December 2005. The main product of the modelling has been to develop a descriptive model of the site (the Site Descriptive Model), i.e. a model describing the geometry, properties of the bedrock and the water and the associated interacting processes and mechanisms. For practical reasons, the Site Descriptive Model is divided into five parts: surface system, geology, rock mechanics, hydrogeology and hydrogeochemistry, which are presented in individual chapters. Four separated models are presented: the geological, rock mechanics, hydrogeological and hydrogeochemical models. The consistency between the hydrogeological and hydrogeochemical models is assessed in a joint chapter. Chapter 1 presents an outline of the report, explains the background to its development and sets out its objectives and scope. It is also introduces and explains the integrated modelling methodology, the nomenclature used in the descriptions of the models and the prediction/outcome studies. Chapter 2 provides a brief overview of the data used for producing the Site Description. Chapters 3 to 8 present the descriptive modelling, which involves interpreting data, interpolating or extrapolating between measurement points and calibrating the model against data, based on the various assumptions made about each conceptual model. Chapter 9 presents the results of the prediction/outcome studies performed during 2005 and Chapter 10 the overall consistency and confidence assessment. Overall conclusions are provided in Chapter 11. The main advances since Site Report 2004 are: A new geological model is presented in Chapter 4, representing a significant change from Bedrock Model 2003/1. There has been extensive use of geological data, whereas hydrogeological data have deliberately not been used and more

  3. Olkiluoto 3: Finland has chosen a EPR

    International Nuclear Information System (INIS)

    Brummer, S.

    2003-01-01

    According to the Finn law any nuclear project has to be declared conformed to the general interest of the country by the government and then has to be approved by the parliament. In may 2002 the Finn parliament approved the project of the TVO company: the construction of a new nuclear unit on the Olkiluoto site and the direct and definitive disposal of spent fuels in the granite underground layers of the same site. The project was agreed with 109 votes for and 92 against. In september 2002 an international invitation to tender was launched and 4 companies made proposals: Westinghouse, Atomstroexport, Framatome-ANP and General Electric. Westinghouse withdrew its offer some time later. In october 2003 TVO announced that the unit will be a 1600 MW EPR (European pressurized reactor) built by Framatome-ANP. The construction work will begin in spring 2005 and the unit is scheduled to enter into service in 2009. At that time the contribution of nuclear energy to the Finn energy production will reach 35%. (A.C.)

  4. Studies of quaternary deposits in investigation trench OL-TK19 on the Olkiluoto study site, Eurajoki, SW Finland

    International Nuclear Information System (INIS)

    Huhta, P.

    2013-07-01

    The Quaternary deposits in investigation trench OL-TK19 were studied by the Geological Survey of Finland in October 2012. Samples for grain size determinations were taken from 3 vertical profiles, placed about 20-25 m apart along the trench. Two till units was sampled separately. The profiles extended from the soil surface down to bedrock. The samples were first dried in the laboratory after which they were sieved. In addition, the grain size distribution of the < 63 μm fraction was analyzed with the Sedigraph 5100 instrument. Sedimentological observations of the sampling profiles were documented in field by drawing them on a field observation form and the profiles were photographed using a digital camera. In addition, the excavated section was photographed along its whole length. The till cover in OL-TK19 consists of two parts. The surface layer of the till is oxidized, brownish grey sandy till, whereas the lower layer is unoxidized, grey silty till. Dark grey silty till as in the bottom of investigation trenches OL-TK13 and OL-TK14 was not found in this trench. The till layers in OL-TK19 was deposited in the last flow phase of the Weichselian continental ice. Bedrock striations indicate that the ice moved in a NW-SE direction. The till beds smooth bedrock topography. The tills showed no signs of disturbance related to bedrock movements. (orig.)

  5. Studies of quaternary deposits in investigation trench OL-TK17 on the Olkiluoto study site, Eurajoki, SW Finland

    International Nuclear Information System (INIS)

    Huhta, P.

    2010-06-01

    The Quaternary deposits in investigation trench OL-TK17 were studied by the Geological Survey of Finland in summer 2009. Samples for grain size determinations were taken from 13 vertical profiles, placed about 25 m apart along the trench, where bedrock didn't reach surface. Profiles 5 and 6 were done by the side of the trench because of that. Each till bed was sampled separately. The profiles extended from the soil surface down to bedrock. The samples were first dried in the laboratory after which they were sieved. In addition, the grain size distribution of the < 63 μm fraction was analyzed with the Sedigraph 5100 instrument. Sedimentological observations of the sampling profiles were documented in field by drawing them on a field observation form and the profiles were photographed using a digital camera. In addition, the excavated section was photographed along its whole length. The till cover in OL-TK17 consists of two parts. The surface layer of the upper till is oxidized, brown till, whereas the lower layer is unoxidized, grey till. The lower till has been preserved in bedrock depressions. The lower till is compact, dark grey silty till with more than 19 % of clay-size material (under 0.002 mm). The upper till in OL-TK17 was deposited in the last flow phase of the Weichselian continental ice. Bedrock striations indicate that the ice moved in a WNW-ESE direction. The till beds level out the bedrock topography. Weathered, broken bedrock was found in two places at the bottom of the trench near sampling profiles 08, 09 and 10. No signs of postglacial faults were detected either in the tills or in the exposed bedrock. The tills showed no signs of disturbance related to bedrock movements, only icepressed cracks were found in the lower silty compact till over broken bedrock. (orig.)

  6. Studies of quaternary deposits of investigation trench OL-TK13 at the Olkiluoto study site, Eurajoki, SW Finland

    Energy Technology Data Exchange (ETDEWEB)

    Huhta, P. [Geological Survey of Finland, Espoo (Finland)

    2007-05-15

    The Quaternary deposits in investigation trench OL-TK13 were studied by the Geological Survey of Finland in autumn 2006. The investigations were carried out in three phases as the excavation progressed. Samples for grain size determinations were taken from vertical profiles, placed 25 m apart along the trench. The profiles extended from the soil surface down to bedrock or, if the bedrock was covered with water, to the water table. Between 6 and 7 kg of sediment was taken in a bucket with a shovel and placed in plastic bags for transport to the laboratory. The samples were first dried in the laboratory after which they were sieved. In addition, grain size distribution of the < 63 {mu}m fraction was analyzed with the Sedigraph 5100 instrument. Sedimentological observations of the sampling profiles were documented in field by drawing on a field observation form and the profiles were photographed using a digital camera except profiles 7 and 8. In addition, the excavated section was photographed along their whole length. The length of OL-TK13 is approximately 250 m and 11 profiles were studied. The height of the profiles varied from 7.3 m to 2.3 m, with an average of 4.6 m. The till cover in OL-TK13 consist of two parts. The upper till has three layers. Surface layer is oxidized, brown sandy till, which is underlain by grayish brown intermediate layer of sandy till. This layer represents the grounwater table, which is moving up and down. The lower layer is unoxidized, grey sandy till. The thickness of the upper till varies from 2.3 to 5.5 meters. The upper till in OL-TK13 is classified as having a normal amount of cobbles and boulders with the size of the larger clasts varying from 6 to 60 cm. The edges of clasts have been eroded and rounded. The upper till has normal compactness. The lower till has been spared in bedrock depressions. Part of it's material has ascended the upper till. The lower till is compact, dark grey silty till with over 15 % of fine material

  7. Studies of quaternary deposits of investigation trench OL-TK13 at the Olkiluoto study site, Eurajoki, SW Finland

    International Nuclear Information System (INIS)

    Huhta, P.

    2007-05-01

    The Quaternary deposits in investigation trench OL-TK13 were studied by the Geological Survey of Finland in autumn 2006. The investigations were carried out in three phases as the excavation progressed. Samples for grain size determinations were taken from vertical profiles, placed 25 m apart along the trench. The profiles extended from the soil surface down to bedrock or, if the bedrock was covered with water, to the water table. Between 6 and 7 kg of sediment was taken in a bucket with a shovel and placed in plastic bags for transport to the laboratory. The samples were first dried in the laboratory after which they were sieved. In addition, grain size distribution of the < 63 μm fraction was analyzed with the Sedigraph 5100 instrument. Sedimentological observations of the sampling profiles were documented in field by drawing on a field observation form and the profiles were photographed using a digital camera except profiles 7 and 8. In addition, the excavated section was photographed along their whole length. The length of OL-TK13 is approximately 250 m and 11 profiles were studied. The height of the profiles varied from 7.3 m to 2.3 m, with an average of 4.6 m. The till cover in OL-TK13 consist of two parts. The upper till has three layers. Surface layer is oxidized, brown sandy till, which is underlain by grayish brown intermediate layer of sandy till. This layer represents the grounwater table, which is moving up and down. The lower layer is unoxidized, grey sandy till. The thickness of the upper till varies from 2.3 to 5.5 meters. The upper till in OL-TK13 is classified as having a normal amount of cobbles and boulders with the size of the larger clasts varying from 6 to 60 cm. The edges of clasts have been eroded and rounded. The upper till has normal compactness. The lower till has been spared in bedrock depressions. Part of it's material has ascended the upper till. The lower till is compact, dark grey silty till with over 15 % of fine material (under 0

  8. Site scale groundwater flow in Olkiluoto

    Energy Technology Data Exchange (ETDEWEB)

    Loefman, J. [VTT Energy, Espoo (Finland)

    1999-03-01

    Groundwater flow modelling on the site scale has been an essential part of site investigation work carried out at different locations since 1986. The objective of the modelling has been to provide results that characterise the groundwater flow conditions deep in the bedrock. The main result quantities can be used for evaluation of the investigation sites and of the preconditions for safe final disposal of spent nuclear fuel. This study represents the latest modelling effort at Olkiluoto (Finland), and it comprises the transient flow analysis taking into account the effects of density variations and the repository as well as the post-glacial land uplift. The analysis is performed by means of numerical finite element simulation of coupled and transient groundwater flow and solute transport carried out up to 10000 years into the future. This work provides also the results for the site-specific data needs for the block scale groundwater flow modelling at Olkiluoto. Conceptually the fractured bedrock is divided into hydraulic units: the planar fracture zones and the remaining part of the bedrock. The equivalent-continuum (EC) model is applied so that each hydraulic unit is treated as a homogeneous and isotropic continuum with representative average characteristics. All the fracture zones are modelled explicitly and represented by two-dimensional finite elements. A site-specific simulation model for groundwater flow and solute transport is developed on the basis of the latest hydrogeological and hydrogeochemical field investigations at Olkiluoto. The present groundwater table and topography together with a mathematical model describing the land uplift at the Olkiluoto area are employed as a boundary condition at the surface of the model. The overall flow pattern is mostly controlled by the local variations in the topography. Below the island of Olkiluoto the flow direction is mostly downwards, while near the shoreline and below the sea water flows horizontally and

  9. Site scale groundwater flow in Olkiluoto

    International Nuclear Information System (INIS)

    Loefman, J.

    1999-03-01

    Groundwater flow modelling on the site scale has been an essential part of site investigation work carried out at different locations since 1986. The objective of the modelling has been to provide results that characterise the groundwater flow conditions deep in the bedrock. The main result quantities can be used for evaluation of the investigation sites and of the preconditions for safe final disposal of spent nuclear fuel. This study represents the latest modelling effort at Olkiluoto (Finland), and it comprises the transient flow analysis taking into account the effects of density variations and the repository as well as the post-glacial land uplift. The analysis is performed by means of numerical finite element simulation of coupled and transient groundwater flow and solute transport carried out up to 10000 years into the future. This work provides also the results for the site-specific data needs for the block scale groundwater flow modelling at Olkiluoto. Conceptually the fractured bedrock is divided into hydraulic units: the planar fracture zones and the remaining part of the bedrock. The equivalent-continuum (EC) model is applied so that each hydraulic unit is treated as a homogeneous and isotropic continuum with representative average characteristics. All the fracture zones are modelled explicitly and represented by two-dimensional finite elements. A site-specific simulation model for groundwater flow and solute transport is developed on the basis of the latest hydrogeological and hydrogeochemical field investigations at Olkiluoto. The present groundwater table and topography together with a mathematical model describing the land uplift at the Olkiluoto area are employed as a boundary condition at the surface of the model. The overall flow pattern is mostly controlled by the local variations in the topography. Below the island of Olkiluoto the flow direction is mostly downwards, while near the shoreline and below the sea water flows horizontally and

  10. U-Pb ages for two tonalitic gneisses, pegmatitic granites, and K-feldspar porphyries, Olkiluoto study site, Eurajoki, SW Finland

    International Nuclear Information System (INIS)

    Maenttaeri, I.; Lindberg, A.; Aaltonen, I.

    2007-08-01

    Secondary ion microprobe zircon U-Pb ages have been determined for two tonalitic gneisses, two pegmatitic granites, and two potassium feldspar porphyry samples from the Olkiluoto study site, Eurajoki, S-W Finland. Moreover, monazites from the Kfeldspar porphyries were dated using TIMS U-Pb method. The tonalitic gneiss A1879 TTG 1 reveals bimodal zircon population and for A1880 TTG it is homogeneous. The samples yield similar overlapping concordia ages of 1851 ± 5 Ma and 1856 ± 5 Ma, respectively. The pegmatitic granite samples A1881 PGR 1 and A1883 PGR 2 have mostly zircons resembling those of the TTG's. The supposed pegmatitic zircons with high U and low Th are strongly altered. The zircon U-Pb data of A1881 PGR 1 plot roughly in two separate lines on a concordia diagram. The apparently younger ∼1.79 Ga data are all from the high U and low Th/U zircons and therefore certainly set the minimum age for the A1881 PGR 1. It is suggested, that the ∼1.85 Ga data comprise analyses from inherited zircons as it include both lower and higher Th/U zircons and 1.85 Ga coevals with age of the tonalitic gneisses. Thus, the apparent age for the A1881 PGR 1 is ∼1.79 Ga. The U-Pb data of sample A1883 PGR 2 also divide into two groups. The higher Th/U, inherited zircons determine an age of 1852 ± 9 Ma which is the same as that of the TTG's. The low Th/U zircon data scatter and the age of 1.83 Ga for A1883 PGR 2 is only poorly determined. The both potassium feldspar porphyry samples A1882 KFP 1 and A1884 KFP 2 reveal heterogeneous zircon populations. The A1882 KFP 1 zircons showing magmatic zoning in BSE images conceivably determine a concordia age of 1842± 6 Ma for the rock. In addition to that a few ∼1.9 Ga inherited zircon and metamorphic low Th/U rims with ages between 1.88 Ga and 1.83 Ga were detected. The age for the youngest metamorphic zircon rims overlaps with that of the magmatic zircons. The zircons in the other KFP sample A1884 show a wide range of ages

  11. Geomicrobial investigations of groundwaters from Olkiluoto, Haestholmen, Kivetty and Romuvaara, Finland

    International Nuclear Information System (INIS)

    Haveman, S.A.; Pedersen, K.; Ruotsalainen, P.

    1998-08-01

    Groundwater from four deep hard rock sites being considered for nuclear waste disposal in Finland (Olkiluoto, Haestholmen, Kivetty and Romuvaara) were investigated for microbial populations. Bacteria will be present in a waste disposal vault, so it is important to understand the microbiology of any potential site. Groundwater samples were collected from 200 to 950 m depth and included fresh, brackish and saline waters. Samples were collected with a pressurized groundwater sampler, PAVE, which is an excellent tool for microbiological sampling. Total cell numbers were typical for deep groundwater, 105 to 106 cells/ml. Growth media designed using groundwater chemistry data were used for enumeration of methanogens, acetogens, sulfate reducing bacteria (SRB) and iron reducing bacteria (IRB). Microbial populations varied between sites. Iron sulfide fracture minerals are common in the brackish high sulfate groundwaters of Olkiluoto, where SRB predominated. Haestholmen groundwater has high dissolved iron, iron hydroxide fracture minerals and IRB were the main microbial population. Kivetty and Romuvaara had mixed populations. It has been proposed that deep subsurface ecosystems are based on hydrogen and carbon dioxide which provide energy and carbon to support the food chain. Signs of such an ecosystem were seen in Olkiluoto. More study is needed to understand the basis for deep subsurface life. From a microbiological point of view, all sites investigated are equally suitable for nuclear waste disposal. (orig.)

  12. Geomicrobial investigations of groundwaters from Olkiluoto, Haestholmen, Kivetty and Romuvaara, Finland

    Energy Technology Data Exchange (ETDEWEB)

    Haveman, S.A.; Pedersen, K. [Goeteborg Univ. (Sweden); Ruotsalainen, P. [Fintact Oy, Helsinki (Finland)

    1998-08-01

    Groundwater from four deep hard rock sites being considered for nuclear waste disposal in Finland (Olkiluoto, Haestholmen, Kivetty and Romuvaara) were investigated for microbial populations. Bacteria will be present in a waste disposal vault, so it is important to understand the microbiology of any potential site. Groundwater samples were collected from 200 to 950 m depth and included fresh, brackish and saline waters. Samples were collected with a pressurized groundwater sampler, PAVE, which is an excellent tool for microbiological sampling. Total cell numbers were typical for deep groundwater, 105 to 106 cells/ml. Growth media designed using groundwater chemistry data were used for enumeration of methanogens, acetogens, sulfate reducing bacteria (SRB) and iron reducing bacteria (IRB). Microbial populations varied between sites. Iron sulfide fracture minerals are common in the brackish high sulfate groundwaters of Olkiluoto, where SRB predominated. Haestholmen groundwater has high dissolved iron, iron hydroxide fracture minerals and IRB were the main microbial population. Kivetty and Romuvaara had mixed populations. It has been proposed that deep subsurface ecosystems are based on hydrogen and carbon dioxide which provide energy and carbon to support the food chain. Signs of such an ecosystem were seen in Olkiluoto. More study is needed to understand the basis for deep subsurface life. From a microbiological point of view, all sites investigated are equally suitable for nuclear waste disposal. (orig.) 66 refs.

  13. Geological Mapping of Investigation Trenches OL-TK15 and OL-TK16 at the Olkiluoto Study Site, Eurajoki, SW Finland

    International Nuclear Information System (INIS)

    Vaarma, M.; Vuokko, J.

    2009-07-01

    Geological mapping of investigation trenches OL-TK15 and OL-TK16 was carried out by the Geological Survey of Finland (GTK) at the Olkiluoto study site as a part of Posiva Oy's site investigation program for the development of an underground repository for nuclear waste. OL-TK15 is ca. N-S striking and ca. 95 m long, and OL-TK16 is ca. E-W striking and ca. 172 m long. The trenches were cleaned with pressure washer and pressurized air. The rock types were determined in field by naked eyes. Five samples from OL-TK15 and 10 samples from OL-TK16 were thin sectioned and investigated microscopically. In addition, petrophysical measurements were carried out by GTK geophysical laboratory for these samples. The bedrock within the excavation trenches OL-TK15 and OL-TK16 consists mainly of veined gneiss (VGN) with intercalations of mica gneiss (MGN), and mafic gneiss (MFGN) of amphibolite, amphibolite-gneiss, and skarn gneiss. The VGN is frankly solid or intact, fine grained and weakly banded and multiple intruded by granitic and pegmatitic veins and veinlets. Narrow scrappy zones occupied by dark dots of highly altered pseudomorphs after cordierite and/or garnet tend to be common in places. In addition, VGN contains rounded oblong mafic to intermediate fragments due to boudination of competent layers and/or dykes. Some rather narrow pegmatitic and quartz veins cut the previous tectonic structures. The prevailing tectonic structures are strong pervasive foliation and conformal veining of several generations mostly granitic in composition. The strike of the foliation and banding and veining as well, varies a little from NNE to ENE and the dip is ca. 40 - 50 degrees to SE sector, respectively. The younger folding has bent the older foliation and neosomic veining mostly with dextral monoclinic style so that in many places there occur tight kinky nodes and rootles augen like knots showing dextral rotation, too. Due to brittle deformation, there are some shear zones and zones with

  14. Colloids or artefacts? A TVO/SKB cooperation project in Olkiluoto, Finland

    International Nuclear Information System (INIS)

    Laaksoharju, M.; Vuorinen, U.; Snellman, M.; Helenius, J.; Allard, B.; Pettersson, C.; Hinkkanen, H.

    1993-12-01

    TVO (Teollisuuden Voima Oy, Finland) initiated a co-operative task with SKB (Swedish Nuclear Fuel and Waste Management Co.) to critically evaluate colloid sampling methods at the test site in Olkiluoto, SW Finland. Three different colloid sampling methods were compared when sampling borehole OL-KR1 at 613-618 m depth. One possible way to make a conservative in-situ colloid estimation is to omit the contribution from calcite precipitation which is considered to be the main artefact. When this is made the inorganic colloid content (size 1-1000 nm) in Olkiluoto is 184 ±177 ppb consisting of clay minerals, silica, pyrite, goethite and magnesium oxide; the concentration of organic substances are around 100 ppb. The in-situ colloid concentration seems to be low which is in good agreement with experiences from years of sampling in similar environment and depths. The exercise shows the many difficulties encountered when sampling colloids. Small error in the planning, pump rate selection, a lack of precautionary measures, artefact sensitivity of the method etc have a tendency to affect significantly the results on the measured ppb colliod level

  15. DFN Modeling for the Safety Case of the Final Disposal of Spent Nuclear Fuel in Olkiluoto, Finland

    Science.gov (United States)

    Vanhanarkaus, O.

    2017-12-01

    Olkiluoto Island is a site in SW Finland chosen to host a deep geological repository for high-level nuclear waste generated by nuclear power plants of power companies TVO and Fortum. Posiva, a nuclear waste management organization, submitted a construction license application for the Olkiluoto repository to the Finnish government in 2012. A key component of the license application was an integrated geological, hydrological and biological description of the Olkiluoto site. After the safety case was reviewed in 2015 by the Radiation and Nuclear Safety Authority in Finland, Posiva was granted a construction license. Posiva is now preparing an updated safety case for the operating license application to be submitted in 2022, and an update of the discrete fracture network (DFN) model used for site characterization is part of that. The first step describing and modelling the network of fractures in the Olkiluoto bedrock was DFN model version 1 (2009), which presented an initial understanding of the relationships between rock fracturing and geology at the site and identified the important primary controls on fracturing. DFN model version 2 (2012) utilized new subsurface data from additional drillholes, tunnels and excavated underground facilities in ONKALO to better understand spatial variability of the geological controls on geological and hydrogeological fracture properties. DFN version 2 connected fracture geometric and hydraulic properties to distinct tectonic domains and to larger-scale hydraulically conductive fault zones. In the version 2 DFN model, geological and hydrogeological models were developed along separate parallel tracks. The version 3 (2017) DFN model for the Olkiluoto site integrates geological and hydrogeological elements into a single consistent model used for geological, rock mechanical, hydrogeological and hydrogeochemical studies. New elements in the version 3 DFN model include a stochastic description of fractures within Brittle Fault Zones (BFZ

  16. In-situ experiments to investigate rock matrix retention properties in ONKALO, Olkiluoto, Finland

    Energy Technology Data Exchange (ETDEWEB)

    Voutilainen, Mikko; Helariutta, Kerttuli [Helsinki Univ. (Finland). Dept. of Chemistry; Poteri, Antti [Technical Research Centre of Finland VTT (Finland); and others

    2015-07-01

    Spent nuclear fuel from nuclear power plants, owned by TVO (Teollisuuden Voima Oy) and Fortum, is planned to be disposed to a repository at a depth of more than 400 meters in the bedrock of Olkiluoto (Eurajoki, Finland). The repository system of multiple release barriers consists of both manmade and natural barriers. The surrounding rock acts as the last barrier if other barriers fail during passage of the millennia. Therefore, safe disposal of spent nuclear fuel requires information on the radionuclide transport and retention properties within the porous and water-containing rock matrix along the water conducting flow paths. To this end, various types of experiments are being performed and planned within ONKALO, the underground rock characterization facility in Olkiluoto, as part of the project @''rock matrix REtention PROperties'' (REPRO). The research site is located at a depth of 420 meters close to the repository site. The aim is to study the diffusion and sorption properties of nuclear compounds in the rock matrix under real in-situ conditions. The first in-situ experiment was performed during 2012 using HTO, Na-22, Cl-36 and I-125 as tracer nuclides. Breakthrough curves show retention and asymptotic behavior that are in-line with those caused by matrix diffusion and sorption were observed in their breakthrough curves. Weak sorption was also observed in the breakthrough curves of Na-22 and I-125.

  17. Seafloor mapping at Olkiluoto western coast of Finland

    International Nuclear Information System (INIS)

    Ilmarinen, K.; Leinikki, J.; Oulasvirta, P.

    2009-02-01

    The objective of the study was to investigate the seafloor of shallow areas around Olkiluoto island, western Finland. The surveys were carried out by Alleco Ltd. Posiva will use the data for modeling purposes. The investigations included bathymetric surveys, sediment sampling and assessment of benthic macrophytes and macrozoobenthos in the underwater parts of six pre-defined survey transects extending from land to the sea. Sediment sampling and the assessment of benthic organisms were done by SCUBA diving. The study area showed a great variation in environmental conditions. Olkiluoto stands between almost open sea and extremely sheltered river mouth area of Lapinjoki. Two of the transects were more than 7 meters deep and included both hard and soft sand bottom. Whereas rest of the transects were shallow with mostly soft clay, mud and silt bottom. Altogether 27 species of algae including five species of stoneworts (Charophyta), one species of water moss (Bryophyta) and 16 species of vascular plants (Tracheophyta) were found. The most abundant group was vascular plants, between the other groups of macroalgae big differences in the abundance were not seen. Furthermore altogether 43 species of macrozoobenthos (Invertebrata) were found, of which six species were sessile bottom fauna (permanently attached fauna). The most abundant groups in the bottom samples were bivalves (Lamellibranchiata) (996 individuals per m 2 ), snails (Gastropoda) (739 individuals per m 2 ) and polychaetes (Polychaeta) (542 individuals per m 2 ). The total abundance of macrozoobenthos on all transects was 2 899 individuals per m 2 . The biggest groups by biomass were bivalves (fresh weight 87 054 mg per m 2 ) and polychaetes (fresh weight 12 983 mg per m 2 ). Transect 1 was the richest in number of species of the deep and exposed transects 1 and 2. The transect 5 had the highest diversity of all the shallow soft bottom transects 3, 4, 5 and 5a. The high diversity of the transect 1 and 5 may be

  18. Seafloor mapping at Olkiluoto western coast of Finland

    Energy Technology Data Exchange (ETDEWEB)

    Ilmarinen, K.; Leinikki, J.; Oulasvirta, P. (Alleco Oy, Helsinki (Finland))

    2009-02-15

    The objective of the study was to investigate the seafloor of shallow areas around Olkiluoto island, western Finland. The surveys were carried out by Alleco Ltd. Posiva will use the data for modeling purposes. The investigations included bathymetric surveys, sediment sampling and assessment of benthic macrophytes and macrozoobenthos in the underwater parts of six pre-defined survey transects extending from land to the sea. Sediment sampling and the assessment of benthic organisms were done by SCUBA diving. The study area showed a great variation in environmental conditions. Olkiluoto stands between almost open sea and extremely sheltered river mouth area of Lapinjoki. Two of the transects were more than 7 meters deep and included both hard and soft sand bottom. Whereas rest of the transects were shallow with mostly soft clay, mud and silt bottom. Altogether 27 species of algae including five species of stoneworts (Charophyta), one species of water moss (Bryophyta) and 16 species of vascular plants (Tracheophyta) were found. The most abundant group was vascular plants, between the other groups of macroalgae big differences in the abundance were not seen. Furthermore altogether 43 species of macrozoobenthos (Invertebrata) were found, of which six species were sessile bottom fauna (permanently attached fauna). The most abundant groups in the bottom samples were bivalves (Lamellibranchiata) (996 individuals per m2), snails (Gastropoda) (739 individuals per m2) and polychaetes (Polychaeta) (542 individuals per m2). The total abundance of macrozoobenthos on all transects was 2 899 individuals per m2. The biggest groups by biomass were bivalves (fresh weight 87 054 mg per m2) and polychaetes (fresh weight 12 983 mg per m2). Transect 1 was the richest in number of species of the deep and exposed transects 1 and 2. The transect 5 had the highest diversity of all the shallow soft bottom transects 3, 4, 5 and 5a. The high diversity of the transect 1 and 5 may be explained by

  19. Evolution of the Olkiluoto site. Palaeohydrogeochemical considerations

    Energy Technology Data Exchange (ETDEWEB)

    Smellie, J. (ed.) [Conterra AB, Stockholm (Sweden); Pitkaenen, P.; Koskinen, L.; and others

    2014-05-15

    Over the past 20 years a considerable amount of work has been carried out to establish a palaeohydrogeological understanding of the Olkiluoto site and surrounding area, and to integrate this knowledge into the hydrogeochemical and hydrogeological descriptive and modelling programmes. This has involved not only a wide range of well established disciplines such as geology, hydrogeology and hydrochemistry, but also the extraction and determination of rock matrix porewaters by out-diffusion, a relatively new approach in crystalline rock. This required a sophisticated laboratory based input, not only to extract and analyse the porewaters, but also to take into consideration any effects associated to, for example, connected physical porosity and/or geochemical porosity in the rock matrix. In general, there is a good integrated understanding of the Olkiluoto site in terms of the geology, mineralogy, hydrology, hydrochemistry and the overall palaeohydrogeochemical model. The Olkiluoto site has had a complex geological and environmental history from Precambrian to the Quaternary as shown by fluid inclusions in quartz grains and fracture calcites. The Quaternary time period has been dominated by a large climatic variation of cold glacial cycles with temperate interglacials and sea-level changes, all of which have contributed to the hydrogeochemical evolution at the Olkiluoto site. All data indicate that infiltration of aerobic water has systematically been limited to few metres depth in the bedrock at Olkiluoto. Today at about the -300 m elevation level, there exists a distinct change in groundwater chemistry and mean residence time including a redox divide supported by a significant reduction in both the intensity and transmissivity of the water connected fracture networks. These indicate that long term stability (over the time span of glacial cycles) and sufficient buffering capacity of the water-rock system against aerobic infiltration, has dominated continuously until

  20. Evolution of the Olkiluoto site. Palaeohydrogeochemical considerations

    International Nuclear Information System (INIS)

    Smellie, J.; Pitkaenen, P.; Koskinen, L.

    2014-05-01

    Over the past 20 years a considerable amount of work has been carried out to establish a palaeohydrogeological understanding of the Olkiluoto site and surrounding area, and to integrate this knowledge into the hydrogeochemical and hydrogeological descriptive and modelling programmes. This has involved not only a wide range of well established disciplines such as geology, hydrogeology and hydrochemistry, but also the extraction and determination of rock matrix porewaters by out-diffusion, a relatively new approach in crystalline rock. This required a sophisticated laboratory based input, not only to extract and analyse the porewaters, but also to take into consideration any effects associated to, for example, connected physical porosity and/or geochemical porosity in the rock matrix. In general, there is a good integrated understanding of the Olkiluoto site in terms of the geology, mineralogy, hydrology, hydrochemistry and the overall palaeohydrogeochemical model. The Olkiluoto site has had a complex geological and environmental history from Precambrian to the Quaternary as shown by fluid inclusions in quartz grains and fracture calcites. The Quaternary time period has been dominated by a large climatic variation of cold glacial cycles with temperate interglacials and sea-level changes, all of which have contributed to the hydrogeochemical evolution at the Olkiluoto site. All data indicate that infiltration of aerobic water has systematically been limited to few metres depth in the bedrock at Olkiluoto. Today at about the -300 m elevation level, there exists a distinct change in groundwater chemistry and mean residence time including a redox divide supported by a significant reduction in both the intensity and transmissivity of the water connected fracture networks. These indicate that long term stability (over the time span of glacial cycles) and sufficient buffering capacity of the water-rock system against aerobic infiltration, has dominated continuously until

  1. Geochemical modelling of the groundwater at the Olkiluoto site

    International Nuclear Information System (INIS)

    Pitkaenen, P.; Snellman, M.; Leino-Forsman, H.; Vuorinen, U.

    1994-04-01

    A preliminary model for probable processes responsible for the evolution of the groundwater at the nuclear waste investigation site Olkiluoto (in Finland) is presented. The hydrological data was collected from boreholes drilled down to 1000-m depth into crystalline bedrock. Based on chemical, isotopic, petrographic and hydrological data as well as ion plots and speciation calculations with PHREEQE the thermodynamic controls on the water composition and trends constraining these processes are evaluated. In order to determine the reactions which can explain the changes along the flow path during the evolution of groundwater system and to determine to which extent these reactions take place, mass-balance calculations with the NETPATH program were used. Mass transfer calculations with the EQ6 program were used to test the feasibility of the model derived, to predict reaction paths and composition of equilibrium solutions for the redox reactions. (57 refs., 43 figs., 10 tabs.)

  2. Olkiluoto site description 2008. Part 1

    International Nuclear Information System (INIS)

    2009-04-01

    This third version of the Olkiluoto Site Report, produced by the OMTF (Olkiluoto Modelling Task Force), updates the Olkiluoto Site Report 2006 (Andersson et al. 2007) with the data and knowledge obtained up to December 2007. The main product of the modelling has been to develop an updated version of the descriptive model of the site (the Site Descriptive Model), i.e. a model describing the geometry, properties of the bedrock and the water and the associated interacting processes and mechanisms. The Site Descriptive Model is divided into six parts: the surface system, geology, rock mechanics, hydrogeology, hydrogeochemistry and migration, which are presented in individual chapters. Five separated models are presented: the geological, rock mechanics, hydrogeological, hydrogeochemical and migration models. The main advances since Site Report 2006 are: (1) The geological model has been revised according to new data and interpretations. This has improved the consistency between the locations of the deformation zones in the geological model and the hydraulic zones in the hydrogeological model, (2) New 3D seismic data have been incorporated within the geological model and an initial model for the eastern part of the Island is presented. Site-scale brittle deformation zones are extrapolated to intersect the surrounding regional lineaments, unless prohibited by direct observations to the contrary. The alteration model has been revised, showing a clear correspondence between the illitisation and the sitescale fault zones, (3) A first account of the development of the brittle deformation history of the site is provided, (4) A new geological DFN model has been developed, that considers mapped fracture traces from both the surface and the ONKALO, (5) A new stress state model and fracture and fracture zone properties are presented, (6) A new hydrogeological DFN model has been developed, (7) An updated site scale (EPM) flow model has been developed, (8) There has been an

  3. Future vegetation types and related main processes for Olkiluoto site

    International Nuclear Information System (INIS)

    Haapanen, R.

    2007-07-01

    This working report summarizes current knowledge of the land up-lift induced vegetation succession and future vegetation types on Olkiluoto Island and its surroundings. The report is based on generic literature and site-specific studies concerning Olkiluoto Island. Current vegetation on Olkiluoto Island and typical succession lines on different soil types are described, as well as main factors affecting the succession. Most relevant materials on hand are listed. Some problems and possible areas to be emphasized before using the data in modelling work are pointed out. (orig.)

  4. Isotopic Evidence for Microbial Activity in Crystalline Bedrock Fractures - a Case Study from Olkiluoto, SW Finland

    Science.gov (United States)

    Sahlstedt, E. K.; Karhu, J.; Pitkänen, P.

    2015-12-01

    Changes in the geochemical environment in crystalline bedrock fractures were investigated using the stable isotopes of C, O and S in fracture filling minerals as tracers. Of special interest were the possible changes which may occur in the subsurface at low temperatures. Especially, the influence of microbial activity was recognized as a catalyst for inducing changes in the geochemical environment. The study site is the Olkiluoto island located on the western coast of Finland, planned to host a geological repository for nuclear waste. Fracture surfaces were investigated to recognize the latest mineralizations at the site. These fillings were comprised of thin plates or small euhedral crystals of calcite and pyrite. The carbon and sulfur isotope compositions of calcite and pyrite were measured from bulk material by conventional IRMS, and in situ by secondary ion mass spectrometry. A notable feature of the late-stage fillings was high variabilities in the δ13C values of calcite and the δ34S values of pyrite, which ranged from -53.8 ‰ to +31.6 ‰ and from -50.4 ‰ to +77.7 ‰, respectively. Based on the isotopic compositions of the fillings, several features in the past hydrogeochemical environment could be recognized. The isotopic composition of the fracture fillings indicate an environment which was stratified with respect to depth. Characteristic features include bacterial sulfate reduction (BSR) occurring at depths 50 m. It appears that methanic conditions were replaced by sulfate reduction at depths >50 m likely due to infiltration of SO42--rich brackish waters. Sulfate reducing bacteria used mainly surface derived organic carbon as electron donors. Some indication of minor methanotrophic activity was recognized in anomalously low δ13C values of calcite, down to -53.8 ‰, at the depth range of 34-54 m. This methanotrophic activity may have been related to bacteria using CH4 as an electron donor in BSR.

  5. Sampling and characterisation of groundwater colloids at ONKALO, Olkiluoto, Finland

    International Nuclear Information System (INIS)

    Takala, M.; Manninen, P.

    2006-11-01

    The purpose of this sampling campaign was to test different filtering methods and filter membranes, to determine the colloid concentration and to characterise the composition of the colloid phase at ONKALO groundwater station ONK-PVA1 at Olkiluoto. The sampling was done on 18 to 19 April 2006. The filtering methods tested were downhole in-situ filtration and in-line syringe filtration. The membranes tested were Anopore 0.2-μm membrane and Nuclepore 0.05 -μm membrane. The Anopore filter was designed to be 0.02 -μm, but according to the SEM micrograph the nominal pore size of the membranes was 0.2 -μm. The size distributions were determined by single particle analysis of the SEM micrographs taken from the used filter membranes. The size distribution can be expressed as a function of the Pareto power law (Buffle, 1988). Parameters A and b of the Pareto power law distribution were determined by using the least square sum method. The particle and mass concentrations were then calculated using the Pareto power law. The size distribution varied between the filtering methods, so that the syringe filtered samples indicated less aggregation than the downhole filtered samples. The colloid concentrations were higher in the Nuclepore filter membranes. This is probably due to the shorter settling time prior to the sampling or differences in the membrane pore size and material. The concentration of the colloid phase determined from the anopore membranes (0.05-1 -μm) was 0.2-0.4 mg/L. The water samples were analysed at the accredited laboratory of Consulting Engineers Paavo Ristola Ltd. The differences in the element concentrations were not detectable between the filtered and unfiltered samples. Contamination with, e.g., nickel, aluminium and organic carbon was evident. The valves, fittings and filter membranes probably caused the contamination. An EDS spectrum was taken from the downhole filtered Nuclepore membrane. The filter cake showed traces of aluminium, silicon and

  6. Surface 3-D reflection seismics - implementation at the Olkiluoto site

    Energy Technology Data Exchange (ETDEWEB)

    Saksa, P.; Lehtimaeki, T.; Heikkinen, E. [Poeyry Environment Oy, Vantaa (Finland)

    2007-03-15

    Posiva Oy takes care of the final disposal of spent nuclear fuel in Finland. In year 2001 Olkiluoto was selected for the site of final disposal. Construction of the underground research facility, ONKALO, is going on at the Olkiluoto site. The aim of this work was to study the possibilities for surface 3-D seismics and to review experiences for design before field work. The physical parameters and geometric properties of the site, as well as efficient survey layout and source arrangements, were considered in this work. Reflection seismics is most used geophysical investigation method in oil exploration and earth studies in sedimentary environment. Recently method has also been applied in crystalline bedrock for ore exploration and nuclear waste disposal site investigations. The advantage of the method is high accuracy combined with large depth of investigation. The principles of seismic 2-D and 3-D soundings are well known and advanced. 3-D sounding is a straightforward expansion of 2-D line based surveying. In investigation of crystalline bedrock, the high frequency wave sources and receivers, their right use in measurements and careful processing procedure (refraction static corrections in particular) are important. Using the site parameters in 2-D numerical modeling, two cases of faulted thin layer at depths of 200, 400 and 600 meters were studied. The first case was a layer with vertical dislocation (a ramp) and the other a layer having limited width of dislocated part. Central frequencies were 100, 200, 400 and 700 Hz. Results indicate that 10 - 20 m dislocation is recognizable, but for depths greater than 600 m, over 20 meters is required. Width of the dislocated part will affect the detectability of vertical displacement. At depths of 200 m and 400 m 10 - 50 m wide parts appear as point-like scatterers, wider areas have more continuity. Dislocations larger than 20 m can be seen. From depth of 600 m over 100 m wide parts are discernible, narrower are visible

  7. Surface 3-D reflection seismics - implementation at the Olkiluoto site

    International Nuclear Information System (INIS)

    Saksa, P.; Lehtimaeki, T.; Heikkinen, E.

    2007-03-01

    Posiva Oy takes care of the final disposal of spent nuclear fuel in Finland. In year 2001 Olkiluoto was selected for the site of final disposal. Construction of the underground research facility, ONKALO, is going on at the Olkiluoto site. The aim of this work was to study the possibilities for surface 3-D seismics and to review experiences for design before field work. The physical parameters and geometric properties of the site, as well as efficient survey layout and source arrangements, were considered in this work. Reflection seismics is most used geophysical investigation method in oil exploration and earth studies in sedimentary environment. Recently method has also been applied in crystalline bedrock for ore exploration and nuclear waste disposal site investigations. The advantage of the method is high accuracy combined with large depth of investigation. The principles of seismic 2-D and 3-D soundings are well known and advanced. 3-D sounding is a straightforward expansion of 2-D line based surveying. In investigation of crystalline bedrock, the high frequency wave sources and receivers, their right use in measurements and careful processing procedure (refraction static corrections in particular) are important. Using the site parameters in 2-D numerical modeling, two cases of faulted thin layer at depths of 200, 400 and 600 meters were studied. The first case was a layer with vertical dislocation (a ramp) and the other a layer having limited width of dislocated part. Central frequencies were 100, 200, 400 and 700 Hz. Results indicate that 10 - 20 m dislocation is recognizable, but for depths greater than 600 m, over 20 meters is required. Width of the dislocated part will affect the detectability of vertical displacement. At depths of 200 m and 400 m 10 - 50 m wide parts appear as point-like scatterers, wider areas have more continuity. Dislocations larger than 20 m can be seen. From depth of 600 m over 100 m wide parts are discernible, narrower are visible

  8. Land uplift in the Olkiluoto-Pyhaejaervi area, southwestern Finland, during the last 8000 years

    International Nuclear Information System (INIS)

    Eronen, M.; Glueckert, G.; Rantala, P.; Plassche, O. van de; Plicht, J. van der

    1995-12-01

    Land is rising in relation to sea level several millimetres per year on the coast of southwestern Finland. The aim of the study was to gather information about the land uplift process. Sediment samples were collected from 14 lakes lying at different altitudes in the area between Olkiluoto and Lake Pyhaejaervi in southwestern Finland to study the relative sea-level changes and land uplift. The present-day lakes had once been below the waters of the Baltic, but due to uplift they had been isolated from the sea one after another. The isolation points in the sediments were determined by preliminary diatom analyses. They show the change from brackish to fresh-water conditions, and these horizons were then dated by two radiocarbon assays. (37 refs., 18 figs., 1 tab.)

  9. TURVA-2012 safety case for licensing a spent fuel repository at Olkiluoto, Finland

    International Nuclear Information System (INIS)

    Vira, Juhani; Snellman, Margit

    2014-01-01

    In 2001, the Finnish Parliament endorsed a decision-in-principle (DiP) whereby the spent nuclear fuel produced by the operating nuclear reactors at Olkiluoto and Loviisa will be disposed of in a geological repository at Olkiluoto, on the south-western coast of Finland. Subsequently, additional DiPs were issued allowing the extension of the repository to accommodate spent nuclear fuel from additional reactors that are under construction or in planning at Olkiluoto, which means a total of 9 000 tU of spent nuclear fuel to be disposed of. In accordance with the decision of the Ministry of Trade and Industry (KTM) in 2003, Posiva submitted an application for a license to construct a disposal facility at Olkiluoto in 2012, consisting of an encapsulation facility and an underground deep geological repository. The application included a Preliminary Safety Analysis Report (PSAR) and a long-term safety case, TURVA-2012. Assuming a positive outcome of the current licensing review, the next step would be the Final Safety Analysis Report (FSAR) in support of an operational licence application around 2020. The disposal method is based on the same KBS-3 concept that the Swedish SKB has used as basis for their license application in 2010. Accordingly, the spent nuclear fuel will be encapsulated in water- and gas-tight copper canisters equipped with a load-bearing insert and emplaced in a deep geological repository constructed in the bedrock. The canisters will be surrounded by a swelling clay buffer material that isolates them from the bedrock. The deposition tunnels and the central tunnels and the other underground openings will be backfilled with materials of low permeability. The repository will be at a depth of about 400-450 m below ground. The primary role of the bedrock is to provide sufficiently stable conditions for the engineered barrier system and to make inadvertent human intrusion unlikely. In case of EBS failure, the bedrock shall also retain and retard the possible

  10. Concentration ratios to great cormorant (Phalacrocorax carbo) at Olkiluoto repository site

    Energy Technology Data Exchange (ETDEWEB)

    Kangasniemi, Ville; Ikonen, Ari T.K. [Environmental Research and Assessment EnviroCase, Ltd., Hallituskatu 1 D 4, 28100 Pori (Finland); Haavisto, Fiia [FM Meri and Erae Oy, Seijaistentie 133a, 21230 Lemu (Finland); Salmi, Juhani A. [Finnish Game and Fisheries Research Institute, Itaeinen Pitkaekatu 3, 20520 Turku (Finland)

    2014-07-01

    Olkiluoto Island on the western coast of Finland has been selected as a repository site for spent nuclear fuel disposal. The great cormorant was a common species in the Finnish coastal area and possibly also a resource for human uses before the decline of the cormorant population in the 18. century. During the last decade, the great cormorant has become again a relevant part of food web in the Bothnian Sea coastal area. Due to the regulatory requirements, the biosphere assessment demonstrating the long-term safety of the repository is developed into more and more site specific. As the adequate literature data on common waterfowl is sparse or in some cases lacking, samples of adult cormorants, eggs and guano together with water and fish samples were collected from the Olkiluoto coastal area. This contribution will present concentration ratios of stable element based on these samples with focus on the elements of a high relevance to the biosphere assessment of the Olkiluoto spent fuel repository together with discussion on the role of food (fish) versus the application of the water-to-bird concentration ratio. (authors)

  11. Understanding brittle deformation at the Olkiluoto site. Literature compilation for site characterization and geological modelling

    International Nuclear Information System (INIS)

    Millnes, A.G.

    2006-07-01

    The present report arose from the belief that geological modelling at Olkiluoto, Finland, where an underground repository for spent nuclear fuel is at present under construction, could be significantly improved by an increased understanding of the phenomena being modelled, in conjunction with the more sophisticated data acquisition and processing methods which are now being introduced. Since the geological model is the necessary basis for the rock engineering and hydrological models, which in turn provide the foundation for identifying suitable rock volumes underground and for demonstrating longterm safety, its scientific basis is of critical importance. As a contribution to improving this scientific basis, the literature on brittle deformation in the Earth's crust has been reviewed, and key references chosen and arranged, with the particular geology of the Olkiluoto site in mind. The result is a compilation of scientific articles, reports and books on some of the key topics, which are of significance for an improved understanding of brittle deformation of hard, crystalline rocks, such as those typical for Olkiluoto. The report is subdivided into six Chapters, covering (1) background information, (2) important aspects of the fabric of intact rock, (3) fracture mechanics and brittle microtectonics, (4) fracture data acquisition and processing, for the statistical characterisation and modelling of fracture systems, (5) the characterisation of brittle deformation zones for deterministic modelling, and (6) the regional geological framework of the Olkiluoto site. The Chapters are subdivided into a number of Sections, and each Section into a number of Topics. The citations are mainly collected under each Topic, embedded in a short explanatory text or listed chronologically without comment. The systematic arrangement of Chapters, Sections and Topics is such that the Table of Contents can be used to focus quickly on the theme of interest without the necessity of looking

  12. Regional distribution of microbes in groundwater from Haestholmen, Kivetty, Olkiluoto and Romuvaara, Finland

    Energy Technology Data Exchange (ETDEWEB)

    Haveman, S.A.; Nilsson, E.L.; Pedersen, K. [Goeteborg University (Sweden)

    2000-06-01

    Groundwater was sampled with the PAVE groundwater sampling system from eight boreholes at Haestholmen, Kivetty, Olkiluoto and Romuvaara, Finland, in 1998 and 1999, for investigation of microbial populations. The groundwater samples had a wide range of salinity and chemistry and contained 104-105 cells per ml, which is typical for subsurface groundwater. In preparing culture media, two approaches were used and compared. Natural, groundwater-based media were prepared from groundwater from the same section of each borehole tested, and synthetic media were prepared based on groundwater chemistry data. No significant difference was observed between the two types of media for brackish and saline groundwater. The groundwater to a depth of 750 m contained mainly sulphate-reducing bacteria (SRB), ironreducing bacteria (IRB) and heterotrophic acetogenic (HA) bacteria. Autotrophic acetogenic (AA) bacteria and methanogenic archaea were found in some samples. Iron-reducing and HA bacteria predominated in brackish groundwater from Haestholmen, with SRB present in smaller numbers. A different microbial population was found in deep saline groundwater from Haestholmen and Olkiluoto that consists of a large proportion of a saline or brine end member. No SRB or AA bacteria were cultured; instead, the microbial population consisted of HA bacteria and either IRB or methanogens. In Olkiluoto, SRB predominated in the brackish and saline groundwater at depths to about 500 m, while methanogens were found in deeper saline groundwater. Stable isotope data (C-13) indicated that the methanogens are part of an autotrophic population consuming dissolved inorganic carbon (DIC) and hydrogen and producing methane and organic carbon. This deep ecosystem may be independent of surface life processes. A high-level radioactive waste (HLW) repository at 500 m depth in the Fennoscandian Shield will be inhabited by SRB, IRB and acetogens. Methanogens may also be present. These anaerobic micro

  13. Engineering rock mass classification of the Olkiluoto investigation site

    Energy Technology Data Exchange (ETDEWEB)

    Aeikaes, K. [ed.; Hagros, A.; Johansson, E. [Saanio and Riekkola Consulting Engineers, Helsinki (Finland)] [and others

    2000-06-01

    Olkiluoto in Eurajoki is being investigated as a possible site for the final disposal of spent nuclear fuel from the Finnish nuclear power plants. The selection of the depth, placement and layout of the repository is affected by the constructability of the bedrock. The constructability, in turn, is influenced by several properties of the host rock, such as its Ethology, the extent of fracturing, its hydrogeological properties and rock engineering characteristics and also by the magnitude and orientation of the in situ stresses and the chemistry of the groundwater. The constructability can be evaluated by the application of a rock classification system in which the properties of the host rock are assessed against common rock engineering judgements associated with underground construction. These judgements are based partly on measurements of in situ stresses and the properties of the bedrock determined from rock samples, but an important aspect is also the practical experience which has been gained during underground excavation in similar conditions and rock types. The aim of the engineering rock mass classification was to determine suitable bedrock volumes for the construction of the repository and has used data from the site characterisation programme carried out at Olkiluoto, which consisted of both surface studies and borehole investigations. The classification specifies three categories of constructability - normal, demanding and very demanding. In addition, rock mass quality has also been classified according to the empirical Q-system to enable a comparison to be made. The rock mass parameters that determine the constructability of the bedrock at Olkiluoto depend primarily on the depth and the Ethology, as well as on whether construction takes place in intact or in fractured rock. The differences in the characteristics of intact rock within a single rock type have been shown to be small. The major lithological unit at Olkiluoto, the mica gneiss, lies in the

  14. Active Microbial Communities Inhabit Sulphate-Methane Interphase in Deep Bedrock Fracture Fluids in Olkiluoto, Finland

    Directory of Open Access Journals (Sweden)

    Malin Bomberg

    2015-01-01

    Full Text Available Active microbial communities of deep crystalline bedrock fracture water were investigated from seven different boreholes in Olkiluoto (Western Finland using bacterial and archaeal 16S rRNA, dsrB, and mcrA gene transcript targeted 454 pyrosequencing. Over a depth range of 296–798 m below ground surface the microbial communities changed according to depth, salinity gradient, and sulphate and methane concentrations. The highest bacterial diversity was observed in the sulphate-methane mixing zone (SMMZ at 250–350 m depth, whereas archaeal diversity was highest in the lowest boundaries of the SMMZ. Sulphide-oxidizing ε-proteobacteria (Sulfurimonas sp. dominated in the SMMZ and γ-proteobacteria (Pseudomonas spp. below the SMMZ. The active archaeal communities consisted mostly of ANME-2D and Thermoplasmatales groups, although Methermicoccaceae, Methanobacteriaceae, and Thermoplasmatales (SAGMEG, TMG were more common at 415–559 m depth. Typical indicator microorganisms for sulphate-methane transition zones in marine sediments, such as ANME-1 archaea, α-, β- and δ-proteobacteria, JS1, Actinomycetes, Planctomycetes, Chloroflexi, and MBGB Crenarchaeota were detected at specific depths. DsrB genes were most numerous and most actively transcribed in the SMMZ while the mcrA gene concentration was highest in the deep methane rich groundwater. Our results demonstrate that active and highly diverse but sparse and stratified microbial communities inhabit the Fennoscandian deep bedrock ecosystems.

  15. Developing methodology for description of biosphere evolution at Olkiluoto disposal site utilising forest studies at other land uplift sites

    International Nuclear Information System (INIS)

    Ikondn, A.T.K.; Afo, L.

    2004-01-01

    In Finland, Olkiluoto Island has been selected as the site for final disposal of spent nuclear fuel, in addition to the existing repository for low and intermediate level waste. When creating biosphere models for safety assessments, local main features and processes need to be taken into account. A special characteristic of the site, as well as the coastal area of the Gulf of Bothnia in general, is the land uplift (6-9 mm/a). This continuously exposes new land to soil-formation processes and provides surfaces for colonization by plant communities. The forest vegetation succession on stony, fine-grained till soils starts from deciduous shoreline vegetation and ends in almost pure Norway spruce forests. This has enabled to study ecological and microbiological processes in soils and forests of different developmental stages, to monitor forest condition and the factors affecting it in sites locating close to each other. It has also made possible gradient studies of the succession of boreal mire ecosystems without a need to wait thousands of years. Applying a methodology described in the full paper, a descriptive model on the evolution of the biosphere will be established to indicate possible ecosystem distributions and main characteristics on the area on the basis of above-mentioned studies carried out by Finnish Forest Research Institute, and of results of the site investigations at Olkiluoto. In future, the evolution description will be used as a basis for selection of appropriate ecosystem modules and parameter values in the subsequent coupled assessment model systems. (author)

  16. Simulation of hydraulic disturbances caused by the underground rock characterisation facility in Olkiluoto, Finland

    International Nuclear Information System (INIS)

    Loefman, J.; Ferenc, M.

    2004-01-01

    Spent fuel from the Finnish nuclear power plants will be disposed of in a repository to be excavated in crystalline bedrock at a depth of 400-700 metres in Olkiluoto. The extensive site investigations carried out since the early 1980's will next focus on the construction of an underground rock characterisation facility (ONKALO) in 2004-2010. The open tunnel system will constitute a major hydraulic disturbance for the site's groundwater conditions for hundreds of years. Especially, inflow of groundwater into the tunnels results in a drawdown of groundwater table and upcoming of deep saline groundwater, which the present study aimed to assess by means of a 3D finite element simulation. The modelled bedrock volume, which horizontally covered the whole Olkiluoto island, was conceptually divided into hydraulic units, planar fracture zones and sparsely fractured rock between the zones, which were both separately treated as porous media. The geometry of the fracture zones was based on the geological bedrock model. Simulations showed that without engineering measures (e.g. grouting) taken to limit inflow of groundwater into the open tunnels, the hydraulic disturbances could be drastic. The tunnels draw groundwater from all directions in the bedrock. A major part of inflow comes from the well-conductive subhorizontal fracture zones intersected by the access tunnel and the shaft. The simulations show that the resulting drawdown of groundwater table may be from tens to hundreds of metres and the depressed area may extend over the area of the island. The results also indicate that the salinity of groundwater is gradually rising around and below the tunnel system, and locally concentration (TDS) may rise rather high in the vicinity of the tunnels. However, the disturbances can significantly be reduced by the grouting of rock. (orig.)

  17. Safeguards for final disposal of spent nuclear fuel. Methods and technologies for the Olkiluoto site

    International Nuclear Information System (INIS)

    Okko, O.

    2003-05-01

    The final disposal of the nuclear material shall introduce new safeguards concerns which have not been addressed previously in IAEA safeguards approaches for spent fuel. The encapsulation plant to be built at the site will be the final opportunity for verification of spent fuel assemblies prior to their transfer to the geological repository. Moreover, additional safety and safeguards measures are considered for the underground repository. Integrated safeguards verification systems will also concentrate on environmental monitoring to observe unannounced activities related to possible diversion schemes at the repository site. The final disposal of spent nuclear fuel in geological formation will begin in Finland within 10 years. After the geological site investigations and according to legal decision made in 2001, the final repository of the spent nuclear fuel shall be located at the Olkiluoto site in Eurajoki. The next phase of site investigations contains the construction of an underground facility, called ONKALO, for rock characterisation purposes. The excavation of the ONKALO is scheduled to start in 2004. Later on, the ONKALO may form a part of the final repository. The plans to construct the underground facility for nuclear material signify that the first safeguards measures, e.g. baseline mapping of the site area, need to take prior to the excavation phase. In order to support the development and implementation of the regulatory control of the final disposal programme, STUK established an independent expert group, LOSKA. The group should support the STUK in the development of the technical safeguards requirements, in the implementation of the safeguards and in the evaluation of the plans of the facility operator. This publication includes four background reports produced by this group. The first of these 'NDA verification of spent fuel, monitoring of disposal canisters, interaction of the safeguards and safety issues in the final disposal' describes the new

  18. Geological model of the Olkiluoto site. Version 1.0

    International Nuclear Information System (INIS)

    Mattila, J.; Aaltonen, I.; Kemppainen, K.

    2008-01-01

    The rocks of Olkiluoto can be divided into two major classes: (1) supracrustal high-grade metamorphic rocks including various migmatitic gneisses, tonalitic-granodioriticgranitic gneisses, mica gneisses, quartz gneisses and mafic gneisses, and (2) igneous rocks including pegmatitic granites and diabase dykes. The migmatitic gneisses can further be divided into three subgroups in terms of the type of migmatite structure: veined gneisses, stromatic gneisses and diatexitic gneisses. On the basis of refolding and crosscutting relationships, the metamorphic supracrustal rocks have been subjected to polyphased ductile deformation, consisting of five stages, the D2 being locally the most intensive phase, producing thrust-related folding, strong migmatisation and pervasive foliation. In 3D modelling of the lithological units, an assumption has been made, on the basis of measurements in the outcrops, investigation trenches and drill cores, that the pervasive, composite foliation produced as a result of polyphase ductile deformation has a rather constant attitude in the ONKALO area. Consequently, the strike and dip of the foliation has been used as a tool, through which the lithologies have been correlated between the drillholes and from the surface to the drillholes. The bedrock at the Olkiluoto site has been subjected to extensive hydrothermal alteration, which has taken place at reasonably low temperature conditions, the estimated temperature interval being from slightly over 300 deg C to less than 100 deg C. Two types of alteration can be observed: (1) pervasive (disseminated) alteration and (2) fracture-controlled (veinlet) alteration. Kaolinisation and sulphidisation are the most prominent alteration events in the site area. Sulphides are located in the uppermost part of the model volume following roughly the lithological trend (slightly dipping to the SE). Kaolinite is also located in the uppermost part, but the orientation is opposite to the main lithological trend

  19. Ecosystem characterization strategy at a repository site - Olkiluoto as a case study

    Energy Technology Data Exchange (ETDEWEB)

    Pere, Tuomas [Posiva Oy, Olkiluoto, 27160 Eurajoki (Finland); Kangasniemi, Ville [Environmental Research and Assessment EnviroCase, Ltd., Hallituskatu 1 D 4, 28100 Pori (Finland); Lahdenperae, Anne-Maj [Saanio and Riekkola Oy, Laulukuja 4, 00420 Helsinki (Finland); Aro, Lasse [Finnish Forest Research Institute, Kaironiementie 15, 39700 Parkano (Finland)

    2014-07-01

    Posiva Oy is constructing an underground research facility ONKALO in Olkiluoto, located in the municipality of Eurajoki, Finland. This is part of the plan for final disposal of spent nuclear fuel produced by Posiva's owners: Teollisuuden Voima Oyj and Fortum Power and Heat Oyj. Posiva has applied for construction license for an underground repository, which is planned to start its operation around the year 2020. The final disposal of high-level radioactive waste poses questions of long-term safety and possible processes of radionuclide release in the EBS (Engineered Barrier System) and the geosphere are also modelled as well as possible transport routes in the bedrock. Posiva has also established a monitoring program for the environment and is also conducting modelling of the surface environment and biosphere in Olkiluoto and the surrounding reference area. These serve the purpose of both, site description and modelling of the transport and accumulation of possible radionuclide releases in the surface environment and biosphere. The process of modelling used by Posiva requires the division of the surface environment and biosphere into several categories. In Posiva's classification, ecosystems are divided to two categories: terrestrial and aquatic with terrestrial divided to forests and agricultural areas. These categories are further divided to ecosystem types which include: lake, river, forest, cropland and sea (with coastal sea as a separate type). These types are even further divided to 14 ecosystem sub-types and behind these sub-types, a total of 24 biotopes exist. Soil and sediment types are also classified to 7 classes. The methodology behind the selection of these biotopes and their connection to the modelling of radionuclide transport in the surface environment is further described in the text. Some of the ecosystem types and biotopes are absent in present-day Olkiluoto area, which necessitates the use of reference targets, such as lakes, rivers

  20. Geological Model of the Olkiluoto Site. Version 2.0

    International Nuclear Information System (INIS)

    Aaltonen, I.

    2010-10-01

    The rocks of Olkiluoto can be divided into two major classes: 1) supracrustal high-grade metamorphic rocks including various migmatitic gneisses, tonalitic-granodioriticgranitic gneisses, mica gneisses, quartz gneisses and mafic gneisses, and 2) igneous rocks including pegmatitic granites and diabase dykes. The migmatitic gneisses can further be divided into three subgroups in terms of the type of migmatite structure: veined gneisses, stromatic gneisses and diatexitic gneisses. On the basis of refolding and crosscutting relationships, the metamorphic supracrustal rocks have been subjected to polyphased ductile deformation, consisting of five stages, the D2 being locally the most intensive phase, producing thrust-related folding, strong migmatisation and pervasive foliation. In 3D modelling of the lithological units, an assumption has been made, on the basis of measurements in the outcrops, investigation trenches and drill cores, that the pervasive, composite foliation produced as a result of polyphase ductile deformation has a rather constant attitude in the ONKALO area. Consequently, the strike and dip of the foliation has been used as a tool, through which the lithologies have been correlated between the drillholes and from the surface to the drillholes. In addition, the largest ductile deformation zones and tectonic units are described in 3D model. The bedrock at the Olkiluoto site has been subjected to extensive hydrothermal alteration, which has taken place at reasonably low temperature conditions, the estimated temperature interval being from slightly over 300 deg C to less than 100 deg C. Two types of alteration can be observed: firstly, pervasive alteration and secondly fracturecontrolled alteration. Clay mineralisation and sulphidisation are the most prominent alteration events in the site area. Sulphides are located in the uppermost part of the model volume following roughly the foliation and lithological trend. Kaolinite is also mainly located in the

  1. Environmental Impact Assessment for Olkiluoto 4 Nuclear Power Plant Unit in Finland

    International Nuclear Information System (INIS)

    Dersten, Riitta; Gahmberg, Sini; Takala, Jenni

    2008-01-01

    In order to improve its readiness for constructing additional production capacity, Teollisuuden Voima Oyj (TVO) initiated in spring 2007 the environmental impact assessment procedure (EIA procedure) concerning a new nuclear power plant unit that would possibly be located at Olkiluoto. When assessing the environmental impacts of the Olkiluoto nuclear power plant extension project, the present state of the environment was first examined, and after that, the changes caused by the projects as well as their significance were assessed, taking into account the combined impacts of the operations at Olkiluoto. The environmental impact assessment for the planned nuclear power plant unit covers the entire life cycle of the plant unit. (authors)

  2. Environmental Impact Assessment for Olkiluoto 4 Nuclear Power Plant Unit in Finland

    Energy Technology Data Exchange (ETDEWEB)

    Dersten, Riitta; Gahmberg, Sini; Takala, Jenni [Teollisuuden Voima Oyj, Olkiluoto, FI-27160 Eurajoki (Finland)

    2008-07-01

    In order to improve its readiness for constructing additional production capacity, Teollisuuden Voima Oyj (TVO) initiated in spring 2007 the environmental impact assessment procedure (EIA procedure) concerning a new nuclear power plant unit that would possibly be located at Olkiluoto. When assessing the environmental impacts of the Olkiluoto nuclear power plant extension project, the present state of the environment was first examined, and after that, the changes caused by the projects as well as their significance were assessed, taking into account the combined impacts of the operations at Olkiluoto. The environmental impact assessment for the planned nuclear power plant unit covers the entire life cycle of the plant unit. (authors)

  3. Indicator value of certain aquatic organisms for radioactive substances in the sea areas off the Loviisa and Olkiluoto nuclear power plants (Finland)[Radioecology

    Energy Technology Data Exchange (ETDEWEB)

    Ilus, E.; Klemola, S.; Ikaeheimonen, T.K.; Vartti, V.P.; Mattila, J. [STUK - radiation and Nuclear Safety Authority, Helsinki (Finland)

    2006-04-15

    The results of the marine radioecology studies carried out in 2000-2001 in the sea areas off the Loviisa and Olkiluoto Nuclear Power Plants (South and West coast of Finland) are reported. Extensive regular monitoring programmes of environmental radioactivity have been carried out already for about 30 years in these areas. The aim of the present study was to compare the indicator value of the various members of the aquatic ecosystem with respect to environmental monitoring. Samples were taken from 27 species including phytoplankton (9 samples), zooplankton (9 samples), periphyton (12 samples), macroalgae and vascular plants (16 samples), benthic animals (8 samples), fish (20 samples) and birds (6). Special attention was paid to different tissues and organs of fish and birds, such as flesh, liver, entrails, bones, milt, spawn, eggs, egg shells etc. (in total 64 samples), because there has been a lot of debate among the opponents of nuclear power in the course of time about the role these objects in the environmental monitoring of the power plants. The samples were taken from relatively small areas both in Loviisa and Olkiluoto, which makes the results well comparable inside each of the sites. (au)

  4. Local seismic network at the Olkiluoto site. Annual Report for 2006

    International Nuclear Information System (INIS)

    Saari, J.; Lakio, A.

    2007-05-01

    In February 2002, Posiva Oy established a local seismic network of six stations on the island of Olkiluoto. Later, in June 2004, the seismic network was expanded with two new seismic stations. At that time started the excavation of the underground characterisation facility (the ONKALO) and the basic operation procedure was changed more suitable for the demands of the new situation. The purpose of the microearthquake measurements at Olkiluoto is to improve understanding of the structure, behaviour and long term stability of the bedrock. The studies include both tectonic and excavation-induced microearthquakes. An additional task of monitoring is related to safeguarding of the ONKALO. This report gives the results of microseismic monitoring during the year 2006. Also the changes in the structure and the operation procedure of the network are described. The network has operated continuously in 2006. In the beginning of 2006, the target area of the seismic monitoring expanded to semi-regional scale. Four new seismic stations started in the beginning of February 2006. At the end of the year, two new borehole geophones were installed in order to improve the sensitivity and the depth resolution of the measurements inside the ONKALO block. This report presents also new interpretations of the excavation induced earthquakes that occurred in the ONKALO in 2005. Altogether 2041 events have been located in the Olkiluoto area, in reported time period. The magnitudes of the observed events range from ML = -1.1 to ML = 3.1 (ML magnitude in local Richter's scale). Most of them are explosions. Two of the observed events are be classified as microearthquakes. Evidence of activity that would have influence on the safety of the ONKALO, have not been found. The observed earthquakes occurred in 2006 were small, ML = -0.6 and ML= -0.9. The earthquakes relate to small movements in brittle deformation zones OL-BFZ043 and OL-BFZ034 presented in the geological model of the Olkiluoto site

  5. Geological model of the Olkiluoto site Version O

    International Nuclear Information System (INIS)

    Paulamaeki, S.; Paananen, M.; Gehoer, S.

    2006-05-01

    The geological model of the Olkiluoto site consists of four submodels: the lithological model, the ductile deformation model, the brittle deformation model and the alteration model. The lithological model gives properties of definite rock units that can be defined on the basis the migmatite structures, textures and modal compositions. The ductile deformation model describes and models the products of polyphase ductile deformation, which enables to define the dimensions and geometrical properties of individual lithological units determined in the lithological model. The brittle deformation model describes the products of multiple phases of brittle deformation. The alteration model describes the types, occurrence and the effects of the hydrothermal alteration. The rocks of Olkiluoto can be divided into two major classes: (1) supracrustal high-grade metamorphic rocks including various migmatitic gneisses, tonalitic-granodioriticgranitic gneisses, mica gneisses, quartz gneisses and mafic gneisses, and (2) igneous rocks including pegmatitic granites and diabase dykes. The migmatitic gneisses can further be divided into three subgroups in terms of the type of migmatite structure: veined gneisses, stromatic gneisses and diatexitic gneisses. On the basis of refolding and crosscutting relationships, the metamorphic supracrustal rocks have been subject to polyphased ductile deformation, including five stages. In 3D modelling of the lithological units, an assumption has been made, on the basis of measurements in outcrops, investigation trenches and drill cores, that the pervasive, composite foliation produced as a result a polyphase ductile deformation has a rather constant attitude in the ONKALO area. Consequently, the strike and dip of the foliation has been used as a tool, through which the lithologies have been correlated between the drillholes and from the surface to the drillholes. The bedrock in the Olkiluoto site has been subject to extensive hydrothermal alteration

  6. Posiva safety case hydrogeochemical evolution of the Olkiluoto site

    Energy Technology Data Exchange (ETDEWEB)

    Trinchero, P.; Roman-Ross, G.; Maia, F.; Molinero, J. [Amphos 21 Consulting S.L., Barcelona (Spain)

    2014-03-15

    The goal of the present work is to assess the hydrochemical evolution and related changes in the buffering capacity of the Olkiluoto site using reactive transport models. The analysis covers a number of operational-related and climatic-related modelling periods that take place during a glacial cycle; namely, the present conditions with the open repository (Operational Period), the post-closure conditions (Temperate Period) and a stage of the glacial cycle representative of the ice sheet retreat phase (Melting Period). With the aim of reproducing the interplay between the hydrodynamic and geochemical processes, the reactive transport calculations summarised in this document integrate the results of a hydrogeological model with a number of geochemical reactions whose parameterisation relies on previous site investigation studies. The conceptual model on which the study is based, assumes that the hydrochemical evolution of the groundwater at repository depth is the result of infiltration processes from the surface of the domain to the repository. The infiltration occurs along flowpaths through deformation zones and fractures in the bedrock. The infiltrating water, in turn, undergo geochemical reactions with the rock and minerals, namely calcite and iron sulphide precipitation/dissolution, kinetic dissolution of aluminosilicates, cation exchange and aqueous redox reactions. Mass exchange between the transmissive fractures and the low permeability matrix is simulated using a dual porosity approach for the Temperate and Melting Periods. On the contrary, the Operational Period, which is characterised by high hydraulic gradients with advection being the dominant transport mechanism, is simulated using a single porosity model. In all the reactive transport simulations denoted as 'Base Case', pyrite is assumed to be the main iron sulphide mineral in the fracture filling. A set of sensitivity simulations, denoted as 'Variant Case', has been defined where

  7. The Site Selected. The Local Decision-Making Regarding the Siting of the Spent Nuclear Fuel Repository in Olkiluoto

    International Nuclear Information System (INIS)

    Kojo, Matti

    2006-01-01

    In May 1999 Posiva, the company responsible for the final disposal of spent nuclear fuel in Finland, suggested that the Finnish Government considers only Olkiluoto in Eurajoki in its application of a decision in principle to be a final disposal site. In January 2000 the municipal council of Eurajoki made a positive statement on the decision in principle. The Government made the decision in principle in Dec 2000, and the Parliament ratified the decision in May 2001. The paper is focused on the decision making of Eurajoki municipality regarding the siting of the spent nuclear fuel repository. The paper shows how the interaction between the representatives of the candidate municipality and the nuclear energy industry was the crucial factor in the decision-making. Eurajoki serves as an example, in where the parties reached an agreement of the compensations for the final disposal repository. The negotiations between the Eurajoki municipality and the nuclear energy industry in reaching a positive decision are analysed from the beginning of the 1980s. The main emphasis is however on the years 1996-99, when the nuclear energy industry negotiated with the municipality on the compensation for the final disposal repository. The loss of income was an important reason why some of the councillors of Eurajoki were interested in having the final disposal repository in Olkiluoto. The industry's problem on the other hand was to safeguard the final disposal site. From the TVO's angle Olkiluoto was a potential final disposal site for example for its limited need for transport and for the existing infrastructure. The company used the financial benefits of the project as its trump card. The attitude of Eurajoki municipality to the final disposal of spent nuclear fuel turned positive with the Olkiluoto vision in December 1998, when still five years earlier the municipal council was prepared to act and prevent the final disposal. The future image presented by the municipality now matched

  8. The Site Selected. The Local Decision-Making Regarding the Siting of the Spent Nuclear Fuel Repository in Olkiluoto

    Energy Technology Data Exchange (ETDEWEB)

    Kojo, Matti [Univ. of Tampere (Finland). Dept. of Political Science and International Relations

    2006-09-15

    In May 1999 Posiva, the company responsible for the final disposal of spent nuclear fuel in Finland, suggested that the Finnish Government considers only Olkiluoto in Eurajoki in its application of a decision in principle to be a final disposal site. In January 2000 the municipal council of Eurajoki made a positive statement on the decision in principle. The Government made the decision in principle in Dec 2000, and the Parliament ratified the decision in May 2001. The paper is focused on the decision making of Eurajoki municipality regarding the siting of the spent nuclear fuel repository. The paper shows how the interaction between the representatives of the candidate municipality and the nuclear energy industry was the crucial factor in the decision-making. Eurajoki serves as an example, in where the parties reached an agreement of the compensations for the final disposal repository. The negotiations between the Eurajoki municipality and the nuclear energy industry in reaching a positive decision are analysed from the beginning of the 1980s. The main emphasis is however on the years 1996-99, when the nuclear energy industry negotiated with the municipality on the compensation for the final disposal repository. The loss of income was an important reason why some of the councillors of Eurajoki were interested in having the final disposal repository in Olkiluoto. The industry's problem on the other hand was to safeguard the final disposal site. From the TVO's angle Olkiluoto was a potential final disposal site for example for its limited need for transport and for the existing infrastructure. The company used the financial benefits of the project as its trump card. The attitude of Eurajoki municipality to the final disposal of spent nuclear fuel turned positive with the Olkiluoto vision in December 1998, when still five years earlier the municipal council was prepared to act and prevent the final disposal. The future image presented by the municipality

  9. Chemical and physical properties of the surface sea sediments at the Olkiluoto offshore, South-Western Finland

    International Nuclear Information System (INIS)

    Lahdenperae, A.-M.; Keskinen, A.

    2011-11-01

    Due to land uplift, the present sea sediments near Olkiluoto will be future land areas, and thus important for the transport of possible releases from nuclear waste repositories at the site. Coastal areas are the transition zones between land and sea, and also potential sites for deep groundwater discharge. The geochemical properties of the surface sediments at the Olkiluoto sea area are summarised in this report. Thirteen sediment samples were cored during the R/V Geomari cruise in autumn 2008. In addition, surface sediment samples from six transects, altogether 57 cores, were taken near the Olkiluoto shoreline by diving in the summer of 2008. The analysis procedure included pH, moisture, dry matter, ash and LOI contents, grain size distribution, carbon and nitrogen analyses and the total concentrations of thirtythree elements. The lateral and vertical distribution of element concentrations, especially heavy metals, is caused by variations in transport and sedimentation patterns of particulate matter, in the occurrence of migration processes and bonding types. The distribution pattern in most of the elements is strongly linked to that of organic matter, carbon and fine-grained material contents. The sediments are strongly enriched by some of the studied elements possibly due to anthropogenic load, while others are only moderately or slightly present. However, the source of different natural and anthropogenic loads is not easy to point out. (orig.)

  10. Matrix Pore Water in Low Permeable Crystalline Bedrock: An Archive for the Palaeohydrogeological Evolution of the Olkiluoto Investigation Site

    Energy Technology Data Exchange (ETDEWEB)

    Eichinger, F. [Hydroisotop GmbH, Schweitenkirchen (Germany); Waber, H. N. [Rock-Water Interaction, Institute of Geological Sciences, University of Bern, Bern (Switzerland); Smellie, J. A.T. [Conterra AB, Stockholm (Sweden)

    2013-07-15

    Matrix pore water in the connected inter- and intragranular pore space of low permeable crystalline bedrock interacts with flowing fracture groundwater predominately by diffusion. Based on the slow exchange between the two water reservoirs, matrix pore water acts as an archive of past changes in fracture groundwater compositions and thus of the palaeohydrological history of a site. Matrix pore water of crystalline bedrock from the olkiluoto investigation site (SW Finland) was characterised using the stable water isotopes ({delta}{sup 18}O, {delta}{sup 2}H), combined with the concentrations of dissolved chloride and bromide as natural tracers. The comparison of tracer concentrations in pore water and present day fracture groundwater suggest for the pore water the presence of old, dilute meteoric water components that infiltrated into the fractures during various warm climate stages. These different meteoric components can be discerned based on the diffusion distance between the two reservoirs and brought into context with the palaeohydrological evolution of the site. (author)

  11. A natural example of fluid-mediated brittle-ductile cyclicity in quartz veins from Olkiluoto Island, SW Finland

    Science.gov (United States)

    Marchesini, Barbara; Garofalo, Paolo S.; Viola, Giulio; Mattila, Jussi; Menegon, Luca

    2017-04-01

    Brittle faults are well known as preferential conduits for localised fluid flow in crystalline rocks. Their study can thus reveal fundamental details of the physical-chemical properties of the flowing fluid phase and of the mutual feedbacks between mechanical properties of faults and fluids. Crustal deformation at the brittle-ductile transition may occur by a combination of competing brittle fracturing and viscous flow processes, with short-lived variations in fluid pressure as a viable mechanism to produce this cyclicity switch. Therefore, a detailed study of the fluid phases potentially present in faults can help to better constrain the dynamic evolution of crustal strength within the seismogenic zone, as a function of varying fluid phase characteristics. With the aim to 1) better understand the complexity of brittle-ductile cyclicity under upper to mid-crustal conditions and 2) define the physical and chemical features of the involved fluid phase, we present the preliminary results of a recently launched (micro)structural and geochemical project. We study deformed quartz veins associated with brittle-ductile deformation zones on Olkiluoto Island, chosen as the site for the Finnish deep repository for spent nuclear fuel excavated in the Paleoproterozoic crust of southwestern Finland. The presented results stem from the study of brittle fault zone BFZ300, which is a mixed brittle and ductile deformation zone characterized by complex kinematics and associated with multiple generations of quartz veins, and which serves as a pertinent example of the mechanisms of fluid flow-deformation feedbacks during brittle-ductile cyclicity in nature. A kinematic and dynamic mesostructural study is being integrated with the detailed analysis of petrographic thin sections from the fault core and its immediate surroundings with the aim to reconstruct the mechanical deformation history along the entire deformation zone. Based on the observed microstructures, it was possible to

  12. Structural and K/Ar Illite geochronological constraints on the brittle deformation history of the Olkiluoto Region, Southwest Finland

    International Nuclear Information System (INIS)

    Viola, G.; Zwingmann, H.; Todd, A.; Raven, M.

    2011-07-01

    This study has generated a new conceptual scheme for the > 1.5 Gyr long brittle evolution of southwestern Finland and the Olkiluoto Island. Based on the study of a number of chosen outcrops containing key structural relationships and the analysis of almost two thousands striated fault planes, seven robust paleo stress tensors have been defined. By comparing and contrasting them with known paleostates of stress derived from southeast Sweden and by using absolute and relative geochronological criteria, it was possible to assign them to a number of specific tectonic events that have affected southwest Finland. Uniaxial compression of late Svecofennian age with a regional NNWSSE σ 1 axis was active soon after 1.75 Ga ago, when environmental conditions leading to brittle deformation were first attained in the region. A younger paleostress field with a NE-SW σ 1 axis, transpressive in character, is inferred to have been active soon after and to have caused significant reactivation of some of the structures formed during the first shortening event. A phase of ESE-WNW extension is constrained by a number of stress tensors and direct field evidence and is here tentatively assigned to the Gothian event and the time of rapakivi magmatism. Further NE-SW extension is taken as the last increment of crustal extension in southwestern Finland and is interpreted as having accommodated upper crustal stretching and the formation and infill of the NWSE- elongated Satakunta graben between 1.6 and 1.3 Ga. A significant and wellconstrained phase of c. NE-SW shortening post dated the rapakivi granites as well as the abundant c. 1260 Ma olivine diabase sills in southwestern Finland. A shortening direction of similar age is not described elsewhere in Fennoscandia. We propose that this phase might be the expression of an hitherto unreported phase of compression that caused inversion of the Satakunta graben. Later E-W compression is assigned to the early stages of the Mesoproterozoic

  13. Site scale groundwater flow in Olkiluoto - complementary simulations

    International Nuclear Information System (INIS)

    Loefman, J.

    2000-06-01

    This work comprises of the complementary simulations to the previous groundwater flow analysis at the Olkiluoto site. The objective is to study the effects of flow porosity, conceptual model for solute transport, fracture zones, land uplift and initial conditions on the results. The numerical simulations are carried out up to 10000 years into the future employing the same modelling approach and site-specific flow and transport model as in the previous work except for the differences in the case descriptions. The result quantities considered are the salinity and the driving force in the vicinity of the repository. The salinity field and the driving force are sensitive to the flow porosity and the conceptual model for solute transport. Ten-fold flow porosity and the dual-porosity approach retard the transport of solutes in the bedrock resulting in brackish groundwater conditions at the repository at 10000 years A.P. (in the previous work the groundwater in the repository turned into fresh). The higher driving forces can be attributed to the higher concentration gradients resulting from the opposite effects of the land uplift, which pushes fresh water deeper and deeper into the bedrock, and the higher flow porosity and the dual-porosity model, which retard the transport of solutes. The cases computed (unrealistically) without fracture zones and postglacial land uplift show that they both have effect on the results and can not be ignored in the coupled and transient groundwater flow analyses. The salinity field and the driving force are also sensitive to the initial salinity field especially at the beginning during the first 500 years A.P. The sensitivity will, however, diminish as soon as fresh water dilutes brackish and saline water and decreases the concentration gradients. Fresh water conditions result in also a steady state for the driving force in the repository area. (orig.)

  14. Borehole plugging experiment in OL-KR24 at Olkiluoto, Finland

    International Nuclear Information System (INIS)

    Rautio, T.

    2006-04-01

    Sealing of investigation boreholes has been studied by Svensk Koernbroenslehantering AB (SKB) and Posiva Oy (Posiva) as a part of final disposal research. The proposed principle is that investigation boreholes drilled at a site must not act as a continuous flow path for groundwater but be sealed to become as tight as the surrounding rock. As a part of the investigations SKB and Posiva started the third phase of the joint project 'Cleaning and sealing of investigation boreholes' in 2005. One of the sub-projects was the plugging experiment in borehole OL-KR24 at Olkiluoto. The aim of the experiment was to test all main procedures of borehole sealing concept in practise in a deep borehole. Borehole KR24 was drilled to the depth of 551.11 metres in 2003 and it was located inside the shaft profile in Onkalo. From the surface to the depth of about 120 m the borehole diameter is 98 mm. The rest of the borehole is 75.7 mm in diameter. The borehole is vertical and the inclination is quite accurately 90 degrees. The plugging experiment in borehole OL-KR24 consisted of four main activities: (1) cleaning of the borehole, (2) characterization of the borehole (3) selective stabilisation of the borehole, and (4) emplacement of plugs. The comprehensive cleaning of the borehole was to be done in the first stage to provide the basis for other activities. The aim of characterization was to study the borehole in order to determine the sections for selective stabilisation and the locations for plugs. The characterization phase consisted of caliper measurements, dummy probing and optical borehole imaging (OBI). The aim of selective stabilisation was to show that selected borehole sections can be stabilised using new techniques and methods. One borehole section was reamed from Ω 76 mm to Ω 98 mm. The reamed borehole section should have been filled with sufficient amount of cement-based material to achieve a stable 'concrete tube' after redrilling, but due to encountered problems and

  15. Site and Regional Data for Biosphere Assessment BSA-2009 Supplement to Olkiluoto Biosphere Description 2009

    International Nuclear Information System (INIS)

    Aro, L.; Haapanen, R.; Puhakka, L.; Hjerpe, T.; Kirkkala, T.; Koivunen, S.; Lahdenperae, A.-M.; Salo, T.; Ikonen, A.T.K.; Helin, J.

    2010-06-01

    The safety case for a spent nuclear fuel repository at Olkiluoto includes a computational safety assessment. A site-specific biosphere assessment is an integral part of them both. In 2009 an assessment was conducted to demonstrate preparedness to apply for construction license to the repository in 2012. As a part of the biosphere assessment, the present conditions at the site are described in Olkiluoto biosphere description report for an analogue of the future conditions being simulated in the safety assessment. This report is a supplement to the biosphere description report of 2009 and documents the site and regional data used in the biosphere assessment 'BSA-2009' with respective rationales. (orig.)

  16. Microbiology of transitional groundwater of the porous overburden and underlying fractured bedrock aquifers in Olkiluoto 2004, Finland

    International Nuclear Information System (INIS)

    Pedersen, K.

    2006-07-01

    following present day hypotheses can be drawn. Continued investigations will update and test them. 1. The transient between the shallow and deep biospheres occurs at a very shallow depth, typically within the first 15-25 m. 2. The shallow biosphere is dominated by oxygen consuming microorganisms that will block oxygen migration to deeper groundwater. 3. The groundwater depression caused by construction of ONKALO will most probably move the borderline between the shallow and deep biosphere downwards. 4. As the groundwater depression zone deepens, oxygen will intrude from above and microbial oxidation of ferrous iron and pyrite will occur with a concomitant decrease in pH and the deposition of ferric iron oxides in the aquifers. Later, when the repository is closed and the groundwater level is restored, those oxides will add to the radionuclide retention capacity of the rock. 5. At present, a deep biosphere signature is found at relatively shallow depths in Olkiluoto compared to other sites investigated with the same methods (The SKB sites Forsmark, Oskarshamn and Aespoe). (orig.)

  17. Hydrogeological structure model of the Olkiluoto Site. Update in 2010

    International Nuclear Information System (INIS)

    Vaittinen, T.; Ahokas, H.; Nummela, J.; Paulamaeki, S.

    2011-09-01

    As part of the programme for the final disposal of spent nuclear fuel, a hydrogeological structure model containing the hydraulically significant zones on Olkiluoto Island has been compiled. The structure model describes the deterministic site scale zones that dominate the groundwater flow. The main objective of the study is to provide the geometry and the hydrogeological properties related to the groundwater flow for the zones and the sparsely fractured bedrock to be used in the numerical modelling of groundwater flow and geochemical transport and thereby in the safety assessment. Also, these zones should be taken into account in the repository layout and in the construction of the disposal facility and they have a long-term impact on the evolution of the site and the safety of the disposal repository. The previous hydrogeological model was compiled in 2008 and this updated version is based on data available at the end of May 2010. The updating was based on new hydrogeological observations and a systematic approach covering all drillholes to assess measured fracture transmissivities typical of the site-scale hydrogeological zones. New data consisted of head observations and interpreted pressure and flow responses caused by field activities. Essential background data for the modelling included the ductile deformation model and the site scale brittle deformation zones modelled in the geological model version 2.0. The GSM combine both geological and geophysical investigation data on the site. As a result of the modelling campaign, hydrogeological zones HZ001, HZ008, HZ19A, HZ19B, HZ19C, HZ20A, HZ20B, HZ21, HZ21B, HZ039, HZ099, OL-BFZ100, and HZ146 were included in the structure model. Compared with the previous model, zone HZ004 was replaced with zone HZ146 and zone HZ039 was introduced for the first time. Alternative zone HZ21B was included in the basic model. For the modelled zones, both the zone intersections, describing the fractures with dominating groundwater

  18. The site selection process for a spent fuel repository in Finland. Summary report

    Energy Technology Data Exchange (ETDEWEB)

    McEwen, T. [EnvirosQuantiSci (United Kingdom); Aeikaes, T. [Posiva Oy, Helsinki (Finland)

    2000-12-01

    consequence of the change in primary legislation that resulted in spent fuel from the Loviisa power plant having to be disposed of in Finland, with the result that the island of Haestholmen was added to the list of potential disposal sites, is explained. The results of these detailed investigations are discussed in terms of the development of lithological and structural models of these sites, and with reference to the development of an understanding of their hydrogeological and hydrochemical environments and the generation of groundwater flow and hydrochemical models. These last two subjects are discussed with reference to their significance for spent fuel disposal. In addition, the constructability of the rock mass at these sites is described, including how a repository could be fitted into the rock mass, taking into account site-specific factors, in particular the location and orientation of fracture zones. The constructability of the Olkiluoto site is described in more detail. Other factors that could be of significance for site selection, namely future climate change and seismicity, are also discussed. The selection of Olkiluoto from these four sites is described with reference to the requirements of a disposal site, as specified by Government, and to factors such as long-term safety, the feasibility of repository development, the possibility of repository enlargement, repository operation, social acceptance, land usage and the environmental burden, infrastructure and costs. The conclusions of this analysis and the special issues at Olkiluoto, namely the presence and significance of saline water at depth and the modelling of groundwater flow, are discussed. The further investigations at Olkiluoto, in particular the main aspects to consider when planning the UCRF (Underground Rock Characterisation Facility) at the site, are presented with the aim of indicating the type of work that still needs to be done in order to demonstrate that a disposal facility can be constructed

  19. On-site emergency preparedness in Finland

    International Nuclear Information System (INIS)

    Vilkamo, O.

    1998-01-01

    General scheme of emergency preparedness in Finland is presented including legal framework, emergency organization and detailed description of plans and procedures. Emergency plan in Finland cover the following matters: classification of emergency situations and description of events and accidents, description of emergency organization, description of the arrangements for alerting and data transfer, management of an emergency situation and radiation protection, worker safety and radiation protection, on- and off-site radiation measurements during a preparedness situation, provision of information, rooms, equipment and facilities, post emergency debriefing and measures, a description of the maintenance of preparedness

  20. KBS-3H layout adaptation 2007 for the Olkiluoto site

    International Nuclear Information System (INIS)

    Johansson, Erik; Hagros, Annika; Autio, Jorma; Kirkkomaeki, Timo

    2008-05-01

    As part of the KBS-3H design an Olkiluoto-specific layout of a KBS-3H repository has been produced based on the latest Olkiluoto data and the bedrock model. One of the main goals of this work was to support the evaluation of the feasibility of the one layer KBS-3H concept and to compare the layouts based on the KBS-3H and KBS-3V disposal concepts. The layout presented in this work can be considered only preliminary and involves a number of uncertainties. The percentage of unusable host rock was assumed to be 25% in this work but can change due to the further design of the different components of the KBS-3H disposal system and further development of the host rock criteria. The layout is also significantly affected by the layout-determining fracture zones. In this work 11 major (highly transmissive) fracture zones interpreted to intersect the -420 m level were considered deterministically. The KBS-3H layout requires a larger area than the KBS-3V repository and takes up most of the available area between the major fracture zones HZ20 and HZ21. This is mainly due to the long drift sections occupied by the compartment plugs (30 m) and the bentonite blocks in the blank zones (10 m), which reduces the usability of the host rock and results in larger canister spacings than in the KBS-3V concept, where the positioning of the deposition holes is very flexible and narrow zones with a moderate transmissivity usually have only a minor effect on the locations of the canisters. According to the results, there is enough bedrock in the current investigation area at central Olkiluoto for KBS-3H layout in one layer. However the layout takes up nearly all of the potential bedrock resource and therefore the result is quite sensitive to possible changes in the design bases

  1. Geological 3D model of the investigation niche in ONKALO, Olkiluoto, southwestern Finland

    International Nuclear Information System (INIS)

    Koittola, N.

    2014-07-01

    The main goal of this Master of Science Thesis was to create a geological 3D-model of the investigation niche 3 and its surroundings. The model were created for the needs of the rock mechanical back analysis. This study is a part of Posiva's regional studies for characterization of the bedrock. Totally 4 models were created: lithological model, foliation model, fracture model, and physical rock property model. Besides the modeling, there was also made a study of the migmatite structures in the niche. Used geological and geophysical methods were drill core loggings, tunnel mapping, ground penetration radar, mise-a-la-masse and drill hole geophysics. Four rock types exist at the niche area: veined gneiss, pegmatite granite, diatexitic gneiss and quartz gneiss. The lithological units were modeled primary with the drill core loggings, tunnel mapping and ground penetrating radar. The major lithological units followed the main foliation direction (south dipping). So the continuations were fairly easy to model in the walls and roof, where the data was lacking. Foliation and fractures were modeled as discs, with mid-points at the measurement points of the structure. There were two main foliation directions 164/46 and 62/39. Fractures were more scattered but three fracture sets can be separated: 156/34, 270/85 and 342/83. The first set is mainly from the drill core loggings, second and third from tunnel mapping. Used methods in foliation model were drill core loggings, tunnel mapping and drill hole geophysics. In fracture model used data was from drill core loggings, tunnel mapping, mise-a-la-masse measurements and drill core geophysic. Four anomalous zones were detected with the drill hole geophysics. Three of these zones were associated with intensely fractured zones and one was connected to exceptionally high mica content in the gneiss. Rocks of Olkiluoto are divided into gneisses and magmatic rocks in the geological mapping. Actually almost all Olkiluoto's rocks are

  2. Geological 3D model of the investigation niche in ONKALO, Olkiluoto, southwestern Finland

    Energy Technology Data Exchange (ETDEWEB)

    Koittola, N.

    2014-07-15

    The main goal of this Master of Science Thesis was to create a geological 3D-model of the investigation niche 3 and its surroundings. The model were created for the needs of the rock mechanical back analysis. This study is a part of Posiva's regional studies for characterization of the bedrock. Totally 4 models were created: lithological model, foliation model, fracture model, and physical rock property model. Besides the modeling, there was also made a study of the migmatite structures in the niche. Used geological and geophysical methods were drill core loggings, tunnel mapping, ground penetration radar, mise-a-la-masse and drill hole geophysics. Four rock types exist at the niche area: veined gneiss, pegmatite granite, diatexitic gneiss and quartz gneiss. The lithological units were modeled primary with the drill core loggings, tunnel mapping and ground penetrating radar. The major lithological units followed the main foliation direction (south dipping). So the continuations were fairly easy to model in the walls and roof, where the data was lacking. Foliation and fractures were modeled as discs, with mid-points at the measurement points of the structure. There were two main foliation directions 164/46 and 62/39. Fractures were more scattered but three fracture sets can be separated: 156/34, 270/85 and 342/83. The first set is mainly from the drill core loggings, second and third from tunnel mapping. Used methods in foliation model were drill core loggings, tunnel mapping and drill hole geophysics. In fracture model used data was from drill core loggings, tunnel mapping, mise-a-la-masse measurements and drill core geophysic. Four anomalous zones were detected with the drill hole geophysics. Three of these zones were associated with intensely fractured zones and one was connected to exceptionally high mica content in the gneiss. Rocks of Olkiluoto are divided into gneisses and magmatic rocks in the geological mapping. Actually almost all Olkiluoto

  3. IAEA Mission Sees Safety Commitment at Finland's New Olkiluoto Reactor Before Planned Start in December

    International Nuclear Information System (INIS)

    2018-01-01

    An International Atomic Energy Agency (IAEA) team of experts observed a commitment to safety by the operator of Unit 3 at Finland’s Olkiluoto Nuclear Power Plant, ahead of the Evolutionary Pressurised Water Reactor’s (EPR) planned connection to the grid in December. The team also identified areas for further enhancements as the operator prepares to put the reactor online. The Pre-Operational Safety Review Team (Pre-OSART) concluded an 18-day mission today to assess operational safety at the 1600 MW reactor, located about 280 km northwest of the capital, Helsinki. Finland has engaged France’s Areva SA together with Germany’s Siemens to construct and commission the unit. The operator is Teollisuuden Voima (TVO). Pre-OSART missions aim to improve operational safety by objectively assessing safety performance using the IAEA’s safety standards and proposing recommendations for improvement where appropriate. The review covered the areas of leadership and management for safety; training and qualification; operations; maintenance; technical support; operating experience; radiation protection; chemistry; emergency preparedness and response; accident management; and commissioning. The team identified a number of good practices that will be shared with the nuclear industry globally, including: • The plant has developed and implemented an efficient system for improving knowledge and skills of staff members. • The plant has developed and validated a unique method for performing suspended solids analysis using a microscope, imaging software and a digital camera. • The plant has introduced a system for systematically assessing nuclear safety culture in the plant supplier organization during construction and commissioning. The mission made several recommendations to improve operational safety, including: • Plant management should set appropriate expectations, communicate them to staff and reinforce them in the field. • The plant should improve the

  4. Illite K-Ar dating of fault breccia samples from ONKALO underground research facility, Olkiluoto, Eurajoki, SW Finland

    International Nuclear Information System (INIS)

    Maenttaeri, I.; Mattila, J.; Zwingmann, H.; Todd, A.J.

    2007-08-01

    Illite K-Ar age determinations were done on five fault breccia samples from the ONKALO underground research facility, Olkiluoto, Eurajoki, S-W Finland. The XRD, SEM, and TEM studies and K-Ar analyses were done in John deLaeter Center in Mass Spectrometry at Curtin University, Perth, Western Australia. The <2 micron grain size fractions contain illite, chlorite, dickite, and quartz. All fractions had minor contamination phases comprising mainly of quartz but traces of K-feldspar contamination could be identified in all samples. The authigenic illite shows variable K concentrations. The illite contents of the ONK-PL68 and ONK-PL87 samples are the smallest. The K-Ar ages for the <2 micron fractions vary from ∼0.55 Ga to 1.38 Ga. The sample ONKPL68 yields a K-Ar age of 912 ± 18 Ma corresponding to a Neoproterozoic-Tonian age. This age can be roughly temporally linked with late events related to Sveconorwegian orogeny. Sample ONK-PL87 has a K-Ar age of 550 ± 11 Ma corresponding to a Neoproterozoic - Lower Cambrian age. The samples ONK-PL522 and ONK-PL901 sampled from the storage hall fault show identical K-Ar ages of 1385 ± 27 Ma and 1373 ± 27 Ma, respectively. These correspond to a Mesoproterozoic-Ectasian age related to Subjotnian or Postjotnian events. ONK-PL960 yields a K-Ar age of 1225 ± 24 Ma corresponding to a Mesoproterozoic-Ectasian age. This age agrees well with the ages from Postjotnian diabase dykes in W Finland. The 2-3 % detrital K-feldspar contamination in clay fractions increases the age. Especially for the youngest sample ONK-PL87, the effect may be geologically meaningful as after the correction the age clearly indicates Caledonian events. Moreover, the age for the low K sample ONKPL901 shifts to indicate Postjotnian diabase age. (orig.)

  5. Biosphere analysis - a complementary assessment of dose conversion factors for the Olkiluoto site

    International Nuclear Information System (INIS)

    Kylloenen, J.; Keto, V.

    2010-04-01

    The Olkiluoto site is currently the primary candidate for the final disposal site for spent nuclear fuel from the Olkiluoto and Loviisa NPPs. Safety analysis calculations must be performed to verify the compliance with the long-term safety requirements. The behaviour and distribution of radionuclides in the biosphere is of high importance in these calculations. The aim of this study was to perform a complementary assessment of dose conversion factors for the Olkiluoto site. Posiva has performed extensive analysis on the different ecosystems. In this work the biosphere analysis model of Fortum Nuclear Services (FNS) is used to give an independent estimate of biosphere dose conversion factors for the Olkiluoto site. The following nuclides are analysed: Cl-36, Ni-59, Se-79, Mo-93, Nb-94, Sn-126, I-129 and Cs-135. The FNS model is an equilibrium compartment model in which a steady annual release of 1 Bq of each radionuclide is distributed in different scenarios. The scenarios are the well scenario, which models a small agricultural ecosystem, the lake scenario which models a larger ecosystem with both agriculture and lake use, and sea and transition scenario, which models the behaviour of the radionuclides in marine environments. The scenarios are described and the transfer equations written for the lake scenario. The parameter values are taken from the FNS biosphere database, which has been used in the Finnish L/ILW waste repository safety analyses since mid 1990's. The results of the FNS analysis are compared to those presented in Posiva working report 2000-20 (POSIVA-WR-00-20). The results are of the same order of magnitude for all nuclides except I-129. Since the Posiva and FNS models were independently constructed, the results can be considered as convincing, and the compliance of the results give confidence to the modelling results. (orig.)

  6. Recent wet storage solutions and costs at NPS sites in Finland

    International Nuclear Information System (INIS)

    Salo, J.P.; Tormala, V.P.

    1987-01-01

    In Finland the power companies have chosen the wet storing method when building the two recent interim spent fuel stores at Olkiluoto and Loviisa NPS sites. These decisions were based on extensive comparison studies of different storing methods and designs. TVO's and IVO's stores started operation F Y 1987 and 1984. One of them was built as an away-from-reactor on the NPS site, the other one as an at-reactor-store, wall-to-wall to the NPS process building. The capacity of the Olkiluoto store will be enough for all the spent fuel arising from the 30 years operation of units TVO I and TVO II, 1270-1400 tHM. The stores are unmanned. The vital process systems of both stores and doubled. The project timetables were kept very well. The investment costs were considerably less than generally mentioned in literature, in spite of the severe climatic conditions of the store sites. The costs of the stores added up to 40 and 50 USD/kgU in 1986 currency, without construction time interest costs. The actual operating and maintenance costs of the Loviisa store have been very low during the first three years of operation. It has been estimated that the operating costs of the independent TVO-KPA-STORE will be less than 1.3 million USD/a

  7. Detection of environmental change using hyperspectral remote sensing at Olkiluoto repository site

    International Nuclear Information System (INIS)

    Tuominen, J.; Lipping, T.

    2011-03-01

    In this report methods related to hyperspectral monitoring of Olkiluoto repository site are described. A short introduction to environmental remote sensing is presented, followed by more detailed description of hyperspectral imaging and a review of applications of hyperspectral remote sensing presented in the literature. The trends of future hyperspectral imaging are discussed exploring the possibilities of long-wave infrared hyperspectral imaging. A detailed description of HYPE08 hyperspectral flight campaign at the Olkiluoto region in 2008 is presented. In addition, related pre-processing and atmospheric correction methods, necessary in monitoring use, and the quality control methods applied, are described. Various change detection methods presented in the literature are described, too. Finally, a system for hyperspectral monitoring is proposed. The system is based on continued hyperspectral airborne flight campaigns and precisely defined data processing procedure. (orig.)

  8. Operational safety analysis of the Olkiluoto disposal site

    International Nuclear Information System (INIS)

    Rossi, J.; Suolanen, V.

    2013-11-01

    Radiation doses for workers of the facilities, for inhabitants in the environment and for terrestrial ecosystem possibly caused by the encapsulation and disposal facilities to be built at Olkiluoto during its operation were considered in the study. First the normal encapsulation process is described and then possible incident and accident cases associated to that are identified for this assessment. The study covers both the normal operation of the plant and some hypothetical incidents and accidents. Radioactive releases and radiation doses are evaluated as a consequence of normal operation and some essential incident and accident cases. Release through the ventilation stack is assumed to be filtered (activated when necessary) both in normal operation and in hypothetical abnormal fault and accident cases. In addition the results for unfiltered releases are also presented e.g. for the emergency planning. During about 30 operation years of our four nuclear power plant units there have been found 58 fuel pins failures. Roughly estimating there has been one fuel leakage per year in a facility (includes two units). Based on this and adopting a conservative approach, it is estimated that one fuel pin per year could leak in normal operation during encapsulation process. The release magnitude in incidents and accidents is based on the event chains, which lead to loss of fuel pin tightness followed by a discharge of radionuclides into the handling space and to some degree to the atmosphere through the ventilation stack equipped with redundant filters. The most exposed group of inhabitants is conservatively assumed to live at the distance of 200 meters from the encapsulation and disposal plant and it will receive the largest doses in most dispersion conditions. The dose value to a member of the most exposed group was calculated on the basis of the weather data in such a way that greater dose than obtained here is caused only in 0.5 percent of dispersion conditions. The

  9. Site-to-canister scale flow and transport in Haestholmen, Kivetty, Olkiluoto and Romuvaara

    Energy Technology Data Exchange (ETDEWEB)

    Poteri, A.; Laitinen, M. [VTT Energy, Espoo (Finland)

    1999-05-01

    Radioactive waste is originating from production of electricity in nuclear power plants. Most of the waste has only low or intermediate levels of radioactivity. However, the spent nuclear fuel is highly radioactive and it has to be isolated from the biosphere. The current nuclear waste management plan in Finland is based on direct disposal of the spent nuclear fuel deep underground. The only feasible mechanism for the radionuclides to escape from an underground repository is to be carried by the groundwater flow after the failure of waste containers. The scope of this study is to examine the groundwater flow situation and transport properties in the vicinity of the disposal canister and along the potential release paths from the repository into the biosphere. The results of this study are further applied in the site specific safety analysis of a spent fuel repository. Synthesis is made of the porous medium estimates of the groundwater flow in the regional and site scales and the detailed fracture network analysis of the flow in the canister scale. This synthesis includes estimation of the transport properties from the canister into the biosphere and flow rates around the deposition holes of the waste canisters. The modelling has been carried out for four different sites: Hastholmen, Kivetty, Olkiluoto and Romavaara. According to the simulations groundwater flow rate around the deposition holes is less than about 1 litre/a for about 75 % of the deposition holes. For about 5 % of the deposition holes the flow rates are a few litres per year or higher. The highest flow rates resulted at Hastholmen, in fresh water conditions 10 000 years after present, and at Kivetty. The transport resistances were calculated for the `worst` flow paths that might have impact on the safety of the repository. The total transport resistances from the repository into the biosphere along those flow paths varied between about 40 000 a/m and 5-10{sup 6} a/m. Most of the total transport

  10. Local seismic network at the Olkiluoto site. Annual Report for 2007

    International Nuclear Information System (INIS)

    Saari, J.; Lakio, A.

    2008-05-01

    magnitude in local Richter's scale). All these events are explosions. According to seismic monitoring the rockmass surrounding the ONKALO has been stable in 2007. One of the recorded events was a local microearthquake (M L 1.9) outside the target area of the network. That earthquake occurred 3.1.2007 in Laitila about 40 km from Olkiluoto. Joint interpretation of recordings of three seismic networks (Posiva, Finnish and Swedish national networks) was used when the preliminary fault plane solution of the Laitila earthquake was calculated: The reverse faulting occurred in a nearly vertical N-S oriented fault, which can be associated with mafic dykes in the area.The orientation of the compressional axis related to the microearthquake on (NWSE) is consistent with the estimated maximum in-situ stress field in Olkiluoto and elsewhere in Finland. (orig.)

  11. Sampling and characterisation of groundwater colloids in ONKALO at Olkiluoto, Finland in 2007

    International Nuclear Information System (INIS)

    Takala, M.; Manninen, P.

    2008-08-01

    Colloid samples were collected from ONKALO groundwater station ONK-PVA1 in October 2007 and an additional sample was taken from groundwater station ONK-PVA3 in November 2007. The colloids were collected by filtering the groundwater on site with an Anopore 0.02 μm aluminium oxide filter. In the sampling in October, water samples were also collected to analyse the differences in the water chemistry before and after filtration. The water samples were freeze-dried so that the elements would be concentrated in the water. The colloid concentrations were determined by counting the particles from the SEM micrographs and by calculating the concentration using the micrograph area, the filter area and the filtered volume. The colloid concentration in ONK-PVA1 was very low. The particle concentration within the size range from 0.1 μm to 1 μm was 1.6 x 10 4 pt/L and the mass concentration within the same size range 0.001 μg/L. Owing to the very low concentration, an additional colloid sample was taken from ONK-PVA3. The colloid concentration in ONK-PVA3 within the size range from 0.1 μm to 1 μm was 8.2 x 10 7 pt/L and the mass concentration 0.013 mg/L. When studying the ONKALO groundwater monitoring data it was noticed that in the samples where the colloid concentration was elevated also the sodium fluorescein concentration was probably elevated. This indicated that process water (e.g. drilling water) was present in the water samples. The ONK-PVA1 water probably also contained process water during the colloid sampling performed in 2006. The composition of the colloid phase could not be determined by analysing the differences in the filtered and unfiltered water owing to the low colloid concentration. Furthermore, the aluminium oxide filter caused aluminium contamination. (orig.)

  12. Local negotiation on compensation siting of the spent nuclear fuel repository in Finland

    International Nuclear Information System (INIS)

    Kojo, Matti

    2007-01-01

    The aim of the paper is to analyse the local negotiation process between the Municipality of Eurajoki and the nuclear power company Teollisuuden Voima (TVO) and the nuclear waste management company Posiva Oy. The aim of the negotiations was to find an acceptable form of compensation for siting a spent nuclear fuel repository in Olkiluoto, Finland. The paper includes background information on the siting process in Finland, the local political setting in the Municipality of Eurajoki and a description of the negotiation process. The analysis of the negotiations on compensation is important for better understanding the progress of the Finnish siting process. The paper describes the picture of the contest to host the spent nuclear fuel repository. It also provides more information on the relationship between the Municipality of Eurajoki and the power company TVO. The negotiations on compensation and the roles of various players in the negotiations have not been studied in detail because the minutes of the Vuojoki liaison group were not available before the decision of the Supreme Administrative Court in May 2006. (author)

  13. Understanding the evolution of the repository and the olkiluoto site

    International Nuclear Information System (INIS)

    Koskinen, K.; Pastina, B.

    2008-01-01

    Posiva Safety Case is organised in a portfolio including ten main reports: Site, Spent Fuel Characteristics and Inventories, Canister Design, Repository Design, Process, Evolution of the Repository and the Site, Biosphere Assessment, Radionuclide Transport, Complementary Evaluations of Safety, and Summary. This portfolio constitutes the basis of the Preliminary Safety Assessment Report, which will be presented to the authorities in 2012 as part of the repository construction license application. The Evolution report [1], which is the focus of this paper, is the main advance in the Safety Case portfolio since the implementation of the Safety Case plan [2] in 2005. The report provides the status of current knowledge with respect to the evolution of the site and the engineered barrier system and highlights areas where better understanding is needed. (authors)

  14. Bedrock model of the Olkiluoto area

    International Nuclear Information System (INIS)

    Saksa, P.; Paananen, M.; Paulamaeki, S.; Anttila, P.; Front, K.; Pitkaenen, P.; Hassinen, P.; Ylinen, A.

    1993-07-01

    Site investigations were carried out at Olkiluoto (in Finland) in 1987-1992 in accordance with an investigation programme drawn up by Teollisuuden Voima Oy (TVO). The site was modelled in terms of rock types, fracturing, fracture structures and geohydrological conditions, the main focus of examination was on fracturing and associated hydraulic conductivity. The various properties of the bedrock structures were classified by means of a three-dimensional model. The descriptions of the models were gathered in a computer system for illustration and storage purposes. The rock types at Olkiluoto are migmatite, which may be divided into mica gneiss and veined gneiss, and also tonalite and coarse-grained migmatite granite (pegmatite). (64 refs., 65 figs.)

  15. Final disposal of spent nuclear fuel in Finnish bedrock. Olkiluoto site report

    International Nuclear Information System (INIS)

    Anttila, P.; Ahokas, H.; Front, K.

    1999-06-01

    Posiva Oy is studying the Finnish bedrock for the geological disposal of spent nuclear fuel. The study is based on the site selection research programme started originally in 1983. The programme is in accordance with the decision in principle by the Council of State in 1983 and aims at the selection of one site in 2000. Four sites, Haestholmen in Loviisa, Kivetty in Aeaenekoski, Olkiluoto in Eurajoki and Romuvaara in Kuhmo, have been studied in detail. This report summarises the results of the site investigations carried out at Olkiluoto. The bedrock of the Olkiluoto site consists of Svecofennian metasediments and platonic rocks, 1800-1900 million years in age. Migmatitic mica gneiss is the most abundant rock type, and is intruded by foliated tonalites and granodiorites and massive coarse-grained granites and pegmatites. Five successive plastic deformation phases have been defined. In total, 30 bedrock structures (R-structures) have been modelled at the site. Most of these represent steeply dipping fracture zones, but several sub-horizontal zones, gently dipping to the SE, have also been identified. The rock mass between the fracture zones represents what is termed 'intact rock', which is typically hard, unweathered and sparsely fractured. The R-structures are generally hydraulically more conductive than the intact rock and their mean transmissivity is 3 x 10 -7 m 2 /s. The corresponding mean of the hydraulic conductivity values for the intact rock measured using a 2 m packer interval, is 8 x 10 -13 m/s, if a lognormal distribution for all measured values is assumed. A clear decrease in hydraulic conductivity with depth has been found for the intact rock, and there seems to be a parallel decrease in the transmissivity of structures. In addition, the hydraulically conductive fractures seem to be more frequent and their transmissivities higher in the uppermost 100 - 200 m of the bedrock than at greater depths. The groundwater chemistry reflects the postglacial

  16. Final disposal of spent nuclear fuel in Finnish bedrock. Olkiluoto site report

    Energy Technology Data Exchange (ETDEWEB)

    Anttila, P. [Fortum Engineering Oy, Vantaa (Finland); Ahokas, H. [Fintact Oy, Helsinki (Finland); Front, K. [VTT Communication and Infrastructure, Espoo (Finland)] [and others

    1999-06-01

    Posiva Oy is studying the Finnish bedrock for the geological disposal of spent nuclear fuel. The study is based on the site selection research programme started originally in 1983. The programme is in accordance with the decision in principle by the Council of State in 1983 and aims at the selection of one site in 2000. Four sites, Haestholmen in Loviisa, Kivetty in Aeaenekoski, Olkiluoto in Eurajoki and Romuvaara in Kuhmo, have been studied in detail. This report summarises the results of the site investigations carried out at Olkiluoto. The bedrock of the Olkiluoto site consists of Svecofennian metasediments and platonic rocks, 1800-1900 million years in age. Migmatitic mica gneiss is the most abundant rock type, and is intruded by foliated tonalites and granodiorites and massive coarse-grained granites and pegmatites. Five successive plastic deformation phases have been defined. In total, 30 bedrock structures (R-structures) have been modelled at the site. Most of these represent steeply dipping fracture zones, but several sub-horizontal zones, gently dipping to the SE, have also been identified. The rock mass between the fracture zones represents what is termed `intact rock`, which is typically hard, unweathered and sparsely fractured. The R-structures are generally hydraulically more conductive than the intact rock and their mean transmissivity is 3 x 10{sup -7} m{sup 2}/s. The corresponding mean of the hydraulic conductivity values for the intact rock measured using a 2 m packer interval, is 8 x 10{sup -13} m/s, if a lognormal distribution for all measured values is assumed. A clear decrease in hydraulic conductivity with depth has been found for the intact rock, and there seems to be a parallel decrease in the transmissivity of structures. In addition, the hydraulically conductive fractures seem to be more frequent and their transmissivities higher in the uppermost 100 - 200 m of the bedrock than at greater depths. The groundwater chemistry reflects the

  17. Numbers, biomass and cultivable diversity of microbial populations relate to depth and borehole-specific conditions in groundwater from depths of 4-450 m in Olkiluoto, Finland.

    Science.gov (United States)

    Pedersen, Karsten; Arlinger, Johanna; Eriksson, Sara; Hallbeck, Anna; Hallbeck, Lotta; Johansson, Jessica

    2008-07-01

    Microbiology, chemistry and dissolved gas in groundwater from Olkiluoto, Finland, were analysed over 3 years; samples came from 16 shallow observation tubes and boreholes from depths of 3.9-16.2 m and 14 deep boreholes from depths of 35-742 m. The average total number of cells (TNC) was 3.9 x 10(5) cells per ml in the shallow groundwater and 5.7 x 10(4) cells per ml in the deep groundwater. There was a significant correlation between the amount of biomass, analysed as ATP concentration, and TNC. ATP concentration also correlated with the stacked output of anaerobic most probable number cultivations of nitrate-, iron-, manganese- and sulphate-reducing bacteria, and acetogenic bacteria and methanogens. The numbers and biomass varied at most by approximately three orders of magnitude between boreholes, and TNC and ATP were positively related to the concentration of dissolved organic carbon. Two depth zones were found where the numbers, biomass and diversity of the microbial populations peaked. Shallow groundwater down to a depth of 16.2 m on average contained more biomass and cultivable microorganisms than did deep groundwater, except in a zone at a depth of approximately 300 m where the average biomass and number of cultivable microorganisms approached those of shallow groundwater. Starting at a depth of approximately 300 m, there were steep gradients of decreasing sulphate and increasing methane concentrations with depth; together with the peaks in biomass and sulphide concentration at this depth, these suggest that anaerobic methane oxidation may be a significant process at depth in Olkiluoto.

  18. The geological and structural characterization of the Olkiluoto site in a critical perspective

    International Nuclear Information System (INIS)

    Cosgrove, J.; Jokinen, J.; Siivola, J.; Tiren, S.

    2003-05-01

    This report comments on aspects of Posiva's work relating to the interests of the IMGS (Investigations and Modelling of Geological Structures) Group who is concerned with the potential impact of the tectonic and geological setting of the Olkiluoto site, on the construction a deep repository for spent nuclear fuel. Since the Group's last report (IMGS 2002) a variety of relevant publications have been produced by Posiva. A number of issues have been identified in these documents relating to the procedure for updating the Bedrock model, factors influencing the location and layout of ONKALO, the mapping procedure planned for the access tunnel, the problem of oversimplification and uncertainties and the proposed extension of the repository. These are discussed in the present report. (orig.)

  19. Regional development of river basins in the Olkiluoto-Pyhaejaervi Area, SW Finland, 2000 BP - 8000 AP

    International Nuclear Information System (INIS)

    Ojala, A.E.K.; Virkki, H.; Palmu, J.-P.; Hokkanen, K.; Kaija, J.

    2006-12-01

    Biosphere assessment forms one of the main components in Posiva's Safety Case portfolio and includes analyses of terrain and ecosystem development. Shoreline displacement and changes in surface hydrology form one part of these analyses. In this report, the regional development of the Olkiluoto-Pyhaejaervi area in the time period 2000 BP - 8000 AP was examined by taking into account changes in the surface flow patterns of the Lapinjoki and Eurajoki river basins. A hydrological model, EULA, was developed and applied to investigate the past and future hydrological regimes and changes in the Olkiluoto-Pyhaejaervi study area. As detailed assessment of erosion and sedimentation effects were not within the scope of this study, only their general effects were evaluated. The digital elevation models (DEM) for different time stages (2000, 1500, 1000 and 500 BP; 100, 300, 500, 1000, 1500, 2000, 2500, 3000, 3500, 4000, 4500, 5000, 6000, 7000 and 8000 AP) were compiled taking into account the land uplift and tilting of the Earth's crust. With the aid of various sophisticated GIS tools, the boundaries of the main river basins, the flow patterns of rivers and development of lakes during each stage were modelled. The yearly discharge rates of rivers Eurajoki and Lapinjoki were also evaluated with the assumption that present climatic features prevail during the whole time period 2000 BP - 8000 AP. Finally, the probability of significant changes in the surface water flow routes were estimated during different stages. (orig.)

  20. The geology of the Olkiluoto area

    International Nuclear Information System (INIS)

    Anttila, P.; Paulamaeki, S.; Lindberg, A.; Paananen, M.; Koistinen, T.; Front, K.; Pitkaenen, P.

    1992-12-01

    Teollisuuden Voima Oy (TVO) is preparing for the final disposal of spent nuclear fuel from the Olkiluoto nuclear power plant deep in the Finnish bedrock. An area close to the power plant at Olkiluoto, Eurajoki, was one of the five areas selected in 1987 for the preliminary site investigations. A summary of the geological conditions at the Olkiluoto site is presented in the report

  1. Geochemical modelling of groundwater evolution and residence time at the Olkiluoto site

    International Nuclear Information System (INIS)

    Pitkaenen, P.; Luukkonen, A.; Ruotsalainen, P.; Leino-Forsman, H.; Vuorinen, U.

    1999-05-01

    An understanding of the geochemical evolution of groundwater is an essential part of the performance assessment and safety analysis of the final disposal of radioactive waste into the bedrock. The performance of technical barriers and migration of possibly released radionuclides depend on chemical conditions. A prerequisite for understanding these factors is the ability to specify the water-rock interactions which control chemical conditions in groundwater. The objective of this study is to interpret the processes and factors which control the hydrogeochemistry, such as pH and redox conditions. A model of the hydrogeochemical progress in different parts of the crystalline bedrock at Olkiluoto has been created and the significance of chemical reactions and groundwater mixing along different flowpaths calculated. Long term hydrodynamics have also been evaluated. The interpretation and modelling are based on water samples (63 altogether) obtained from precipitation, Baltic Sea, soil layer, shallow wells in the bedrock, and eight deep boreholes in the bedrock for which a comprehensive data set on dissolved chemical species and isotopes was available. Some analyses of dissolved gases and fracture calcite and their isotopic measurements were also utilised. The data covers the bedrock at Olkiluoto to a depth of 1000 m. The results from groundwater chemistry, isotopes, petrography, hydrogeology of the site, geomicrobial studies, and PCA and speciation calculations were used in the evaluation of evolutionary processes at the site. The geochemical interpretation of water-rock interaction, isotope-chemical evolution and mixing of palaeo water types were approached by mass-balance calculations (NETPATH). Reaction-path calculations (EQ3/6) were used to verify the thermodynamic feasibility of the reaction models obtained. The interpretation and calculation of hydrochemical data from Olkiluoto reveals the complex nature of hydrogeochemical evolution at the site. Changes in

  2. Geochemical modelling of groundwater evolution and residence time at the Olkiluoto site

    Energy Technology Data Exchange (ETDEWEB)

    Pitkaenen, P.; Luukkonen, A. [VTT Communities and Infrastructure, Espoo (Finland); Ruotsalainen, P. [Fintact Oy (Finland); Leino-Forsman, H.; Vuorinen, U. [VTT Chemical Technology, Espoo (Finland)

    1999-05-01

    An understanding of the geochemical evolution of groundwater is an essential part of the performance assessment and safety analysis of the final disposal of radioactive waste into the bedrock. The performance of technical barriers and migration of possibly released radionuclides depend on chemical conditions. A prerequisite for understanding these factors is the ability to specify the water-rock interactions which control chemical conditions in groundwater. The objective of this study is to interpret the processes and factors which control the hydrogeochemistry, such as pH and redox conditions. A model of the hydrogeochemical progress in different parts of the crystalline bedrock at Olkiluoto has been created and the significance of chemical reactions and groundwater mixing along different flowpaths calculated. Long term hydrodynamics have also been evaluated. The interpretation and modelling are based on water samples (63 altogether) obtained from precipitation, Baltic Sea, soil layer, shallow wells in the bedrock, and eight deep boreholes in the bedrock for which a comprehensive data set on dissolved chemical species and isotopes was available. Some analyses of dissolved gases and fracture calcite and their isotopic measurements were also utilised. The data covers the bedrock at Olkiluoto to a depth of 1000 m. The results from groundwater chemistry, isotopes, petrography, hydrogeology of the site, geomicrobial studies, and PCA and speciation calculations were used in the evaluation of evolutionary processes at the site. The geochemical interpretation of water-rock interaction, isotope-chemical evolution and mixing of palaeo water types were approached by mass-balance calculations (NETPATH). Reaction-path calculations (EQ3/6) were used to verify the thermodynamic feasibility of the reaction models obtained. The interpretation and calculation of hydrochemical data from Olkiluoto reveals the complex nature of hydrogeochemical evolution at the site. Changes in

  3. Geological data acquisition for site characterisation at Olkiluoto: a framework for the phase of underground investigations

    International Nuclear Information System (INIS)

    Milnes, A.G.; Aaltonen, I.; Kemppainen, K.; Mattila, J.; Wikstroem, L.; Front, K.; Kaerki, A.; Gehoer, S.; Paulamaeki, S.; Paananen, M.; Ahokas, T.

    2007-05-01

    'Geological data acquisition' is a general term for the collection of observations and measurements by direct observation of exposed bedrock in the field (i.e. in natural outcrops and trenches, in drillholes, and in tunnels and other underground excavations). Only field-based data acquisition is included in this report: laboratory-based investigations will be continued, based on the field data and sampling, and all the data will be subject to discipline-specific processing, as the project proceeds. The ultimate aim of geological data acquisition is to provide the necessary data base for geological models of the bedrock of the Olkiluoto site, in connection with the construction of an underground rock characterisation facility, ONKALO, and a repository for spent nuclear fuel, at about 500m depth. Geological data acquisition plays a central role in site characterisation and modelling, and is intended to provide a solid platform on which the other disciplines (rock mechanics, hydrogeology, seismic risk assessment, etc.) can base their investigations. Based on consideration of a series of guidelines (e.g. modelling scale, source of data, level of investigation, national and international experience, special conditions at Olkiluoto, need for process understanding), a project-oriented 'framework' has been developed as a background to the different projects within the geological data acquisition programme. Each project will require its own system of data acquisition (methodology, spreadsheets, protocols, etc.), as described in the corresponding reports; the present report concentrates on the general principles which lie behind the different methodologies and data sheets. These principles are treated under three main headings: characterization of intact rock, characterization of deformation zone intersections, and characterization of individual fractures. Geological mapping of natural outcrops and trenches at Olkiluoto, and lithological logging of more than 40 rock cores

  4. Normal evolution of a spent fuel repository at the candidate sites in Finland

    International Nuclear Information System (INIS)

    Grawford, M.B.; Wilmot, R.D.

    1998-12-01

    The Finnish disposal concept for spent nuclear fuel envisages burial of the fuel in a repository excavated at a depth of around 500 m in crystalline bedrock. Since 1983, a programme has been underway in Finland to select a potential site for such a repository. The programme is now in the final stages of selecting one site for further detailed characterisation from a list of four candidate sites at Kivetty, Romuvaara, Olkiluoto, and Haestholmen. Each stage of the site selection process has been supported by a major performance assessment (PA) exercise. The aim of this report is to describe the normal evolution of a repository system at the four candidate Finnish sites as input to development of the next PA, known as TILA-99. The report summarises the disposal concept and the present-day characteristics of each candidate site, and considers the most likely future changes in both the natural environment and the engineered components of the disposal system. The description concentrates on the key features, events and processes (FEPs) controlling behaviour and evolution of the disposal system. It is assumed that all the canisters are intact following emplacement and repository closure. FEPs that occur but which do not significantly affect system behaviour and evolution are only briefly described. FEPs with a low probability of occurrence are mentioned as appropriate. The report provides a map to the key Finnish reports and other work that underlies and supports the description of normal evolution. Differences between the four candidate sites in terms of their expected normal evolution are summarised. None of the differences are sufficient to prevent each site from behaving as a 'normal' site, the evolution of which is summarised over time in the final section of the report. (author)

  5. Normal evolution of a spent fuel repository at the candidate sites in Finland

    Energy Technology Data Exchange (ETDEWEB)

    Grawford, M.B.; Wilmot, R.D. [Galson Sciences Limited, Rutland (United Kingdom)

    1998-12-01

    The Finnish disposal concept for spent nuclear fuel envisages burial of the fuel in a repository excavated at a depth of around 500 m in crystalline bedrock. Since 1983, a programme has been underway in Finland to select a potential site for such a repository. The programme is now in the final stages of selecting one site for further detailed characterisation from a list of four candidate sites at Kivetty, Romuvaara, Olkiluoto, and Haestholmen. Each stage of the site selection process has been supported by a major performance assessment (PA) exercise. The aim of this report is to describe the normal evolution of a repository system at the four candidate Finnish sites as input to development of the next PA, known as TILA-99. The report summarises the disposal concept and the present-day characteristics of each candidate site, and considers the most likely future changes in both the natural environment and the engineered components of the disposal system. The description concentrates on the key features, events and processes (FEPs) controlling behaviour and evolution of the disposal system. It is assumed that all the canisters are intact following emplacement and repository closure. FEPs that occur but which do not significantly affect system behaviour and evolution are only briefly described. FEPs with a low probability of occurrence are mentioned as appropriate. The report provides a map to the key Finnish reports and other work that underlies and supports the description of normal evolution. Differences between the four candidate sites in terms of their expected normal evolution are summarised. None of the differences are sufficient to prevent each site from behaving as a `normal` site, the evolution of which is summarised over time in the final section of the report. (author) 155 refs.

  6. Evaluation and modelling of a potential repository site - Olkiluoto case study

    International Nuclear Information System (INIS)

    Saksa, P.; Ahokas, H.; Loefman, J.; Pitkaenen, P.; Paulamaeki, S.; Snellman, M.

    1998-01-01

    The observations, interpretations and estimates resulting from site investigations were developed into conceptual bedrock model of the Olkiluoto area. Model development has been an interdisciplinary process and three major iterations have occurred. Geochemical sampling and a programme of electromagnetic and electrical soundings were carried out and interpreted to model occurrences of groundwater types. The parametrisation and modifications needed between geological models and ground-water flow simulation model is discussed. The latest groundwater flow modelling effort comprises the transient flow analysis taking into account the effects of density variations, the repository, post-glacial land uplift and global sea level rise. The main flow modeling result quantities (the amount, direction, velocity and routes as well as concentration of water) are used for evaluation of the investigation sites and of the preconditions for safe final disposal of spent nuclear fuel. Integration of hydrological and hydrogeochemical methods and studies has provided the primary method for investigating the evolution. Testing of flow models with hydro-geochemical information is considered to improve the hydrogeological understanding of a site and increases confidence in conceptual hydrogeological models. Bedrock model allows also comparisons to be made between its time-varying versions. The evolution of fracture frequency, fracture zone structures and hydraulic conductivity has been studied. A prediction-outcome comparison was made in selected boreholes and showed that the rock type was the easiest parameter to predict

  7. Understanding brittle deformation at the Olkiluoto site. Literature Supplement 2010: an Update of Posiva Working Report 2006-25

    Energy Technology Data Exchange (ETDEWEB)

    Milnes, A. (GEA Consulting, Corcelles (CH))

    2011-07-15

    Posiva Working Report 2006-25 arose from the belief that geological modelling at Olkiluoto, Finland, where an underground repository for spent nuclear fuel is at present under construction, could be significantly improved by an increased understanding of the phenomena being modelled, in conjunction with the more sophisticated data acquisition and processing methods which are now being introduced. Since the geological model is the necessary basis for the rock engineering and hydrological models, which in turn provide the foundation for identifying suitable rock volumes underground and for demonstrating long-term safety, its scientific basis is of critical importance. As a contribution to improving this scientific basis, the literature on brittle deformation in the Earth's crust was reviewed up to and including year 2005. The result was a compilation of scientific articles, reports and books on some of the key topics of significance for an improved understanding of brittle deformation of hard, crystalline rocks, particularly heterogeneous migmatitic and metamorphic rocks like those that make up the Olkiluoto bedrock. The present report is a supplement to WR 2006-25, covering the 5-year period 2006-2010, with some key earlier references and an Annotated Bibliography. The present report is subdivided into five chapters, listing recent literature on (1) background subjects and basic principles, (2) the fabric of Olkiluoto-type intact rock (gneisses, migmatites, fault rocks), (3) formation and characteristics of brittle deformation features (fracture mechanics, brittle microtectonics), (4) fracture data acquisition and processing (statistical characterisation and modelling of fracture systems), and (5) the characterisation of brittle deformation zones (for deterministic and dynamic modelling), corresponding to the first five chapters of the earlier report

  8. Understanding brittle deformation at the Olkiluoto site. Literature Supplement 2010: an Update of Posiva Working Report 2006-25

    International Nuclear Information System (INIS)

    Milnes, A.

    2011-07-01

    Posiva Working Report 2006-25 arose from the belief that geological modelling at Olkiluoto, Finland, where an underground repository for spent nuclear fuel is at present under construction, could be significantly improved by an increased understanding of the phenomena being modelled, in conjunction with the more sophisticated data acquisition and processing methods which are now being introduced. Since the geological model is the necessary basis for the rock engineering and hydrological models, which in turn provide the foundation for identifying suitable rock volumes underground and for demonstrating long-term safety, its scientific basis is of critical importance. As a contribution to improving this scientific basis, the literature on brittle deformation in the Earth's crust was reviewed up to and including year 2005. The result was a compilation of scientific articles, reports and books on some of the key topics of significance for an improved understanding of brittle deformation of hard, crystalline rocks, particularly heterogeneous migmatitic and metamorphic rocks like those that make up the Olkiluoto bedrock. The present report is a supplement to WR 2006-25, covering the 5-year period 2006-2010, with some key earlier references and an Annotated Bibliography. The present report is subdivided into five chapters, listing recent literature on (1) background subjects and basic principles, (2) the fabric of Olkiluoto-type intact rock (gneisses, migmatites, fault rocks), (3) formation and characteristics of brittle deformation features (fracture mechanics, brittle microtectonics), (4) fracture data acquisition and processing (statistical characterisation and modelling of fracture systems), and (5) the characterisation of brittle deformation zones (for deterministic and dynamic modelling), corresponding to the first five chapters of the earlier report

  9. U-Pb ages for PGR dykes, KFP, and adjacent older leucosomic PGRs from ONKALO underground research facility, Olkiluoto, Eurajoki, SW Finland

    International Nuclear Information System (INIS)

    Maenttaeri, I.; Engstroem, J.; Lahaye, Y.; Pere, T.

    2010-06-01

    Zircon LA-MC-ICP-MS and monazite TIMS ages have been determined for three PGR dykes (A2018, A2020, and A2070) and a KFP (A2022) from the ONKALO underground research facility, Olkiluoto, Eurajoki, SW Finland. For purposes of comparison, leucosomic PGRs (A2019, A2021, and A2023) crosscut by the PGR dykes and the KFP were also dated. Minimum ages for the PGR dykes and the A2022 KFP were determined by the monazite U-Pb ages. PGR dykes reveal partially overlapping ages of 1826 ± 7 Ma (A2018), 1811 ± 5 Ma (A2020), and 1817 ± 3 Ma (A2070). Monazite age of 1808 ± 6 Ma for the KFP is coeval with the youngest PGR dyke monazite. The ∼1.81-1.80 Ga ages for the supposed PGR dyke zircon agree within the error limits with the monazite ages. For the KFP, obvious co-magmatic zircon was not identified. The metamorphic zircon rims and domains found from the PGR dykes reveal multiphase overprinting, the ages ranging from 1.86 Ga to 1.80 Ga. Subsequently, the high-U PGR dyke zircon suffered major lead loss during the Rapakivi event at 1.58 Ga and finally, a few grains show early Devonian age of ∼400 Ma. In the KFP, many structurally homogeneous zircon domains and rims plot on a ∼1.80 Ga discordia line, while the concordant data are ∼1.83 Ga. Leucosomic PGRs A2019 and A2021 crosscut by the PGR dykes enclose 1.87-1.85 Ga zircon resembling and being contemporaneous with the tonalite zircon in the Olkiluoto area. The concordia ages of 1836 ± 13 Ma (A2019) and 1807 ± 11 Ma (A2021) for the metamorphic zircon domains in the leucosomes correlate perfectly with the supposed ages of the crosscutting PGR dykes. The youngest metamorphic zircon phases in leucosome A2023 are dated at 1.82-1.80 Ga. That is in good accordance with the monazite age 1808 ± 6 Ma from the KFP A2022 crosscutting the leucosome A2023. The samples contain also abundant older inherited zircon cores and grains. Archaean ages vary from 3.1 Ga to 2.7 Ga and the older Palaeoproterozoic between 2.1 Ga and 1.9 Ga. The

  10. Geological history and its impact on the rock mechanics properties of the Olkiluoto site

    International Nuclear Information System (INIS)

    Hudson, J.A.; Cosgrove, J.W.

    2006-03-01

    This report is one of three documents with background information for supporting the development of Posiva's future rock mechanics programme. The other two reports are a summary of all the rock mechanics work completed for Posiva before 2005 (Posiva Working Report) and a technical audit of the numerical modeling work that has been conducted previously for Posiva (REC Memo). The purpose of this report is to establish the extent to which the mechanical properties of the rocks at the Olkiluoto site can be estimated from a knowledge of the geological environment. The main information required for rock mechanics studies of the site is a knowledge of the prevailing stress state, the properties of the intact rock, and the properties of the fractures at all scales - from sizes that could form blocks in the tunnel roof up to the major brittle deformation zones that could be influence the location of the ONKALO and the subsequent repository. Thus, the summary of the geological history in Chapter 2 concentrates on these features and we summarise the ductile and brittle deformational tectonic history of the site, with emphasis on the inferred stress states causing the deformations. Then, in Chapter 3, the rock stress, the hierarchy of brittle fracturing, the fracture properties and the mechanical properties of the rock mass are considered in the light of the geological environment. These features provide the baseline knowledge of the host rock from which the logic of the future rock mechanics programme can be developed, based on: the bedrock model; the site investigation results; the requirements for generating the site descriptive model; the prediction-outcome ONKALO studies; and numerically modeling the effects of excavation for design and safety analysis. The implications of this study for the future rock mechanics work are outlined in Chapter 4 with emphasis on the key features for modeling. (orig.)

  11. Fracture-specific pressure measurements at the Olkiluoto site in Eurajoki drillhole OL-KR39

    International Nuclear Information System (INIS)

    Ripatti, K.; Poellaenen, J.; Hurmerinta, E.; Rouhiainen, P.

    2011-12-01

    An option was built to the Posiva Flow Log, Difference flow method (PFL DIFF). A double packer device was combined together with a PFL DIFF probe. The new tool was needed for measurements of the very low hydraulic head. Indications of these were detected earlier in some fractures of drillhole OL-KR39. The target fractures could be measured with the accurate absolute pressure sensor in the PFL DIFF probe. Principles of the methods and the results of measurements are presented in this report. The measurements were carried out in drillhole OL-KR39 at the Olkiluoto investigation site between April 2011 and May 2011. The device used includes a sensor for single point resistance (SPR). SPR measurement is used to place the device accurately on the chosen fracture. The section length limited by the packers is about 1 m. The measurements were carried out in natural (i.e. un-pumped) conditions. The same measuring program was employed in all chosen fractures. Electrical conductivity (EC) of drillhole water and flow rate along the drillhole were also measured in conjunction with the pressure measurements. (orig.)

  12. Geochemical and mineralogical study of selected weathered samples from Olkiluoto site

    International Nuclear Information System (INIS)

    Lindberg, A.

    2009-02-01

    Optical microscopy, chemical analyses and X-ray diffraction method were used to study the influence of weathering from 11 drill core samples from shallow depths (< 25 m). The samples, 4 to 22 cm in length were drilled from Olkiluoto study site, Eurajoki, and they represent the common rock types of local bedrock: mica gneiss, tonalitic and granodioritic gneiss. Two of the samples were macroscopically unweathered and 9 of them were remarkably altered. The alteration was shown as porosity, the abundance of chlorite instead of biotite and pink, unclear feldspars. Many samples also contained red-brown hematite and fractures, some of them coated with secondary minerals, even clay. Microscopically the most visible feature of weathering was the total alteration of plagioclase and cordierite to sericite. In many samples also biotite was richly altered to chlorite and opaque minerals. Microfractures were common and they were filled by hematite, kaolinite and fine-grained muscovite (sericite). Hematite was, in some cases, also largely replacing the weathered minerals, feldspars and cordierite. Chemical alteration was not clear, because the alteration of main minerals have produced secondary minerals with almost the same chemical composition without any reasonable depleting or enrichment of certain elements. X-ray diffraction determination of samples proved, that often plagioclase was replaced by mica and biotite by chlorite. In some cases the samples contained products of chemical weathering, kaolinite and smectite. (orig.)

  13. Geological and geophysical investigations in the selection and characterization of the disposal site for high-level nuclear waste in Finland

    Energy Technology Data Exchange (ETDEWEB)

    Paulamaki, S.; Paananen, M.; Kuivamaki, A. [Geological Survey of Finland, Espoo (Finland); Wikstrom, L. [Posiva Oy, Olkiluoto (Finland)], e-mail: seppo.paulamaki@gtk.fi

    2011-07-01

    Two power companies, Teollisuuden Voima Oy (TVO) and Fortum Power and Heat Oy, are preparing for the final disposal of spent nuclear fuel deep in the Finnish bedrock. In the initial phase of the site selection process in the late 1970s and early 1980s, the Geological Survey of Finland (GTK) examined the general bedrock factors that would have to be taken into account in connection with final disposal with reference to the international guidelines adapted to Finnish conditions. On the basis of extensive basic research data, it was concluded that it is possible to find a potential disposal site that fulfils the geological safety criteria. In the subsequent site selection survey covering the whole of Finland, carried out by GTK in 1983-1985, 101 potential investigation areas were discovered. Eventually, five areas were selected by TVO for preliminary site investigations: Romuvaara and Veitsivaara in the Archaean basement complex, Kivetty and Syyry in the Proterozoic granitoid area, and Olkiluoto (TVO's NPP site) in the Proterozoic migmatite area. The preliminary site investigations at the selected sites in 1987-1992 comprised deep drillings together with geological, geophysical, hydrogeological and hydrogeochemical investigations. A conceptual geological bedrock model was constructed for each site, including lithology, fracturing, fracture zones and hydrogeological conditions. On the basis of preliminary site investigations, TVO selected Romuvaara, Kivetty and Olkiluoto for detailed site investigations to be carried out during 1993-2000. After the feasibility studies, the island of Haestholmen, where Fortum's Loviisa nuclear power plant is located, was added to the list of potential disposal sites. In the detailed site investigations, additional data on bedrock were gathered, the previous conceptual geological, hydrogeological and hydrogeochemical models were complemented, the rock mechanical properties of the bedrock were examined, and the constructability

  14. Geological and geophysical investigations in the selection and characterization of the disposal site for high-level nuclear waste in Finland

    Energy Technology Data Exchange (ETDEWEB)

    Paulamaki, S; Paananen, M; Kuivamaki, A [Geological Survey of Finland, Espoo (Finland); Wikstrom, L. [Posiva Oy, Olkiluoto (Finland)], e-mail: seppo.paulamaki@gtk.fi

    2011-07-01

    Two power companies, Teollisuuden Voima Oy (TVO) and Fortum Power and Heat Oy, are preparing for the final disposal of spent nuclear fuel deep in the Finnish bedrock. In the initial phase of the site selection process in the late 1970s and early 1980s, the Geological Survey of Finland (GTK) examined the general bedrock factors that would have to be taken into account in connection with final disposal with reference to the international guidelines adapted to Finnish conditions. On the basis of extensive basic research data, it was concluded that it is possible to find a potential disposal site that fulfils the geological safety criteria. In the subsequent site selection survey covering the whole of Finland, carried out by GTK in 1983-1985, 101 potential investigation areas were discovered. Eventually, five areas were selected by TVO for preliminary site investigations: Romuvaara and Veitsivaara in the Archaean basement complex, Kivetty and Syyry in the Proterozoic granitoid area, and Olkiluoto (TVO's NPP site) in the Proterozoic migmatite area. The preliminary site investigations at the selected sites in 1987-1992 comprised deep drillings together with geological, geophysical, hydrogeological and hydrogeochemical investigations. A conceptual geological bedrock model was constructed for each site, including lithology, fracturing, fracture zones and hydrogeological conditions. On the basis of preliminary site investigations, TVO selected Romuvaara, Kivetty and Olkiluoto for detailed site investigations to be carried out during 1993-2000. After the feasibility studies, the island of Haestholmen, where Fortum's Loviisa nuclear power plant is located, was added to the list of potential disposal sites. In the detailed site investigations, additional data on bedrock were gathered, the previous conceptual geological, hydrogeological and hydrogeochemical models were complemented, the rock mechanical properties of the bedrock were examined, and the constructability and the

  15. Immobilization of uranium in biofilm microorganisms exposed to groundwater seeps over granitic rock tunnel walls in Olkiluoto, Finland

    Science.gov (United States)

    Krawczyk-Bärsch, Evelyn; Lünsdorf, Heinrich; Pedersen, Karsten; Arnold, Thuro; Bok, Frank; Steudtner, Robin; Lehtinen, Anne; Brendler, Vinzenz

    2012-11-01

    In an underground rock characterization facility, the ONKALO tunnel in Finland, massive 5-10-mm thick biofilms were observed attached to tunnel walls where groundwater was seeping from bedrock fractures at a depth of 70 m. In laboratory experiments performed in a flow cell with detached biofilms to study the effect of uranium on the biofilm, uranium was added to the circulating groundwater (CGW) obtained from the fracture feeding the biofilm. The final uranium concentration in the CGW was adjusted to 4.25 × 10-5 M, in the range expected from a leaking spent nuclear fuel (SNF) canister in a future underground repository. The effects were investigated using microelectrodes to measure pH and Eh, time-resolved laser fluorescence spectroscopy (TRLFS), energy-filtered transmission electron microscopy (EF-TEM), and electron energy-loss spectroscopy (EELS) studies and thermodynamic calculations were utilized as well. The results indicated that the studied biofilms constituted their own microenvironments, which differed significantly from that of the CGW. A pH of 5.37 was recorded inside the biofilm, approximately 3.5 units lower than the pH observed in the CGW, due to sulfide oxidation to sulfuric acid in the biofilm. Similarly, the Eh of +73 mV inside the biofilm was approximately 420 mV lower than the Eh measured in the CGW. Adding uranium increased the pH in the biofilm to 7.27 and reduced the Eh to -164 mV. The changes of Eh and pH influenced the bioavailability of uranium, since microbial metabolic processes are sensitive to metals and their speciation. EF-TEM investigations indicated that uranium in the biofilm was immobilized intracellularly in microorganisms by the formation of metabolically mediated uranyl phosphate, similar to needle-shaped autunite (Ca[UO2]2[PO4]2·2-6H2O) or meta-autunite (Ca[UO2]2[PO4]2·10-12H2O). In contrast, TRLFS studies of the contaminated CGW identified aqueous uranium carbonate species, likely (Ca2UO2[CO3]3), formed due to the high

  16. Microbiology of transitional groundwater of the porous overburden and underlying shallow fractured bedrock aquifers in Olkiluoto, Finland. October 2005 - January 2006

    International Nuclear Information System (INIS)

    Pedersen, K.

    2007-05-01

    The subsurface biosphere on Earth appears to be far more expansive and metabolically and phylogenetically complex than previously thought. A diverse suite of subsurface environments has been reported to support microbial ecosystems, extending from a few meters below the surface to several thousand meters. The discovery of a deep biosphere will have several important implications for underground repositories for radioactive wastes. The main potential effects of microorganisms in the context of a KBS-3 type repository for spent fuel in the bedrock of Olkiluoto are: (1) Oxygen reduction and maintenance of anoxic and reduced conditions. (2) Bio-immobilisation and bio-mobilisation of radionuclides, and the effects from microbial metabolism on radionuclide mobility. (3) Sulphate reduction to sulphide and the risk for copper sulphide corrosion. The main objective of this study was to characterize the geochemistry, biomass and microbial diversity of shallow subsurface groundwater at Olkiluoto, from 4.0 m down to 14.9 m. This objective also permitted the determination of whether or not there is any transition in the shallow depths at Olkiluoto to microbial conditions associated with the deep subsurface. This was the second investigation that covered both shallow and some moderately deep groundwater microbiology in Olkiluoto. The analysis of microbiology is very important for proper understanding of the evolution of geochemical processes in and around the underground research facility ONKALO being constructed at Olkiluoto by Posiva since autumn 2004, as well as for the planned KBS-3 type spent fuel repository at Olkiluoto. There are several conclusions from this investigation that are of importance for ONKALO. The following present day conclusions can be drawn. Continued investigations will update and test them: The shallow biosphere was dominated by oxygen consuming microorganisms that block oxygen migration to deeper groundwater. This effect was most pronounced during the

  17. Local seismic network at the Olkiluoto site. Annual report 2002-2004

    Energy Technology Data Exchange (ETDEWEB)

    Saari, J. [Enprima Oy, Vantaa (Finland)

    2005-09-15

    In Olkiluoto, Posiva Oy has operated a local seismic network since February 2002. In the beginning, the network consisted of six seismic stations. Later, in June 2004, the seismic network was expanded with two new seismic stations. At that time started the excavation of the underground characterisation facility (the ONKALO) and the basic operation procedure was changed more suitable for the demands of the new situation. The purpose of the microearthquake measurements at Olkiluoto is to improve understanding of the structure, behaviour and long term stability of the bedrock. The studies include both tectonic and excavation-induced microearthquakes. An additional task of monitoring is related to safeguarding of the ONKALO. This report gives the results of microseismic monitoring during the years 2002 - 2004. Also the changes in the structure and the operation procedure of the network are described. The network has operated nearly continuously. The longest interruption occurred 16.-17.6.2004, when two new seismic stations were installed in the network and the operation procedure was changed. Altogether 757 events have been located in the Olkiluoto area. The magnitudes of the observed events range from ML = -3.5 to ML = 1.2. All of them are explosions or other artificial events. So far, none of the 757 observed events can be classified as microearthquakes. Five of the events have characteristics that make the origin of the recorded signal uncertain. They are quite unlikely microearthquakes, but they are not typical examples of artificial seismic signals either. When the experience and the data set of the Olkiluoto microearthquakes increase the identification of events will be more definite. Evidence of activity that would has influence on the safety of the ONKALO, have not found. (orig.)

  18. Local seismic network at the Olkiluoto site. Annual report 2002-2004

    International Nuclear Information System (INIS)

    Saari, J.

    2005-09-01

    In Olkiluoto, Posiva Oy has operated a local seismic network since February 2002. In the beginning, the network consisted of six seismic stations. Later, in June 2004, the seismic network was expanded with two new seismic stations. At that time started the excavation of the underground characterisation facility (the ONKALO) and the basic operation procedure was changed more suitable for the demands of the new situation. The purpose of the microearthquake measurements at Olkiluoto is to improve understanding of the structure, behaviour and long term stability of the bedrock. The studies include both tectonic and excavation-induced microearthquakes. An additional task of monitoring is related to safeguarding of the ONKALO. This report gives the results of microseismic monitoring during the years 2002 - 2004. Also the changes in the structure and the operation procedure of the network are described. The network has operated nearly continuously. The longest interruption occurred 16.-17.6.2004, when two new seismic stations were installed in the network and the operation procedure was changed. Altogether 757 events have been located in the Olkiluoto area. The magnitudes of the observed events range from ML = -3.5 to ML = 1.2. All of them are explosions or other artificial events. So far, none of the 757 observed events can be classified as microearthquakes. Five of the events have characteristics that make the origin of the recorded signal uncertain. They are quite unlikely microearthquakes, but they are not typical examples of artificial seismic signals either. When the experience and the data set of the Olkiluoto microearthquakes increase the identification of events will be more definite. Evidence of activity that would has influence on the safety of the ONKALO, have not found. (orig.)

  19. Potential reference mires and lakes ecosystems for biosphere assessment of Olkiluoto site

    International Nuclear Information System (INIS)

    Haapanen, R.; Aro, L.; Kirkkala, T.; Paloheimo, A.; Koivunen, S.; Lahdenperae, A.-M.

    2010-10-01

    New lakes and mires will develop in the sea area now surrounding Olkiluoto Island due to the postglacial land uplift. The properties of these objects can be forecast using data from existing lakes and mires. There are, however, no such objects on the present Olkiluoto Island. This Working Report presents a project, initiated in 2007, where lakes and mires at different successional stages, suitable as reference objects for the future ones, were searched. The task included delineation of the study area, based on e.g. geological and climatological factors, and development of the selection criteria. As background, development history and properties of present lakes and mires in the study area are described in this report. For this and forthcoming projects, several GIS data sets were acquired. With help of these data, literature and environmental databases, 33 mires and 27 lakes were selected. These were considered to be the best available analogues for the future objects around Olkiluoto Island. The characteristics of these objects are presented briefly; more detailed information is found in the literature and databases. (orig.)

  20. Layout Determining Features, their Influence Zones and Respect Distances at the Olkiluoto Site

    International Nuclear Information System (INIS)

    Pere, T.; Ahokas, H.; Vaittinen, T.; Wikstroem, L.

    2012-12-01

    Fault zones located at the site of an underground nuclear waste repository may pose a risk to the repository by acting as potential hosts for earthquakes during the present day or future stress fields and having the possibility to induce secondary displacements on nearby large fractures, which may damage the nuclear waste canisters, if being intersected by such fractures. The fault zones may additionally provide possible flow routes, important for the transport of radionuclides and the chemical stability of the repository. It is therefore important to identify such structures, defined as layout determining features (LDF), and to assess their influence on the surrounding host rock and to determine respect volumes to the structures, which are avoided in the layout planning in order to mitigate the possible harmful effects to the repository. Fault zones with a trace length of 3 km or more are considered as layout determining features as these can potentially host an earthquake of a magnitude of 5.5 or more and may thus induce secondary displacements larger than 5 cm on nearby fractures, which is held as the current canister damage threshold premise. Fault zones with a size less than 3 km are considered unlikely candidates to induce secondary displacements of 5 cm or larger. In addition to the earthquake potential, hydrogeological zones with high T -value (geometrical mean T ≤ 10 -6 m 2 /s) and large dimensions (at least several hundred metres) are also defined as layout determining features. For each layout determining feature an influence zone is defined, depicting a volume around a fault zone or a hydrogeological zone with increased fracture density and permeability, often also called as damage zones in the scientific literature. Influence zones are therefore considered as mechanically weak and/or transmissive parts of the host rock, which may cause harmful effects to the performance of the repository if intersecting deposition tunnels or deposition holes. In

  1. Landscape modelling case studies for Olkiluoto site in 2005-2006

    International Nuclear Information System (INIS)

    Broed, R.

    2007-05-01

    This report documents the landscape modelling test cases implemented in the fall of 2005, complemented in 2006. The objective of the report is to illustrate the application of the landscape modelling methodology, to investigate the important factors of influence and to clarify methodological aspects. The results of this analysis are intended to serve as a basis for future assessments. Landscape modelling represents an approach for estimating doses to inhabitants of a landscape consisting of several interacting ecosystems which are affected by the contamination from potential radionuclide releases from a deep geological repository. From the model outputs, Landscape Dose Conversion Factors (LDFs) are calculated. These represent, for each radionuclide of concern, an estimate of the equilibrium dose arising from a constant unit release of activity into the landscape objects. Modelling is undertaken in the current report for static landscapes corresponding to future landscape configurations forecasted for four different points in time. The results of this modelling are not yet suitable for practical application to estimate doses which could result from the planned repository at the Olkiluoto site. To suit this eventual purpose, refinements of the modelling and reduced uncertainty of the important parameters used in the models will be necessary. The current report intends rather to investigate the important factors influencing modelled future doses arising from the planned repository and to clarify methodological aspects. Notwithstanding the restrictions of the current modelling, important conclusions already can be drawn from the results presented in this report. Several methodological aspects are addressed in this report. These are, in particular, the impact of the landscape configurations on the resulting dose estimates, the importance of model parameters and assumptions for the assessment results, the database for radionuclides requiring consideration, the importance

  2. Local seismic network at the Olkiluoto site. Annual report for 2013

    International Nuclear Information System (INIS)

    Saari, J.; Malm, M.

    2014-06-01

    This report gives the results of microseismic monitoring during 2013. Excavation of the underground rock characterisation facility called ONKALO started in 2004. Before that, in February 2002, Posiva Oy established a local seismic network of six stations on the island of Olkiluoto, where there are currently 17 seismic stations and 21 triaxial sensors. The network has operated continuously in 2013. The purpose of the microearthquake measurements at Olkiluoto is to improve understanding of the structure, behaviour and long term stability of the bedrock. The investigation area includes two target areas, of which the larger one, the seismic semiregional area, includes the Olkiluoto island and its surroundings. The purpose is to monitor explosions and tectonic earthquakes in regional scale inside that area. All the expected excavation induced events are assumed to occur inside the smaller target area, the seismic ONKALO block, which is a 2 km x 2 km x 2 km cube surrounding the ONKALO and includes 13 seismic stations. An additional task of monitoring is related to safeguarding of the construction of ONKALO. Upgrade and unification of the whole seismic network was done in August 2013. The upgrade included communication, data acquisition, server equipment in Olkiluoto, network configuration and software. The bedrock models and the ONKALO design model applied in the visualisation of the seismicity remained the same in 2013. The number of located events was much smaller than during previous years due to break in the excavation. Altogether 436 events have been located in the Olkiluoto area, in the reported time period. Nearly half of the observed explosions (237) in 2013 occurred inside the seismic semi-regional area and especially inside the seismic ONKALO block (137). The magnitudes of the explosions inside the semi-regional area range from M L = -1.6 to M L = 1.5 (M L = magnitude in local Richter's scale). One small induced earthquake (ML = -1.8) was detected on 9 May 2013

  3. Seismic network at the Olkiluoto site and microearthquake observations in 2002-2013

    International Nuclear Information System (INIS)

    Saari, J.; Malm, M.

    2014-05-01

    This report describes the structure and operation of Posiva's seismic network after the comprehensive upgrade performed in 2013 and presents a summary of its micro-earthquake observations in 2002 - 2013. Excavation of the underground rock characterisation facility called ONKALO started in 2004. Before that, in February 2002, Posiva Oy established a local seismic network of six stations on the island of Olkiluoto. The number of seismic stations has increased gradually and communication, hardware and software have developed in over ten years. The upgrade in 2013 included data transmission, the equipment in several seismic stations, the server responsible for the data processing in Olkiluoto and software applied in operation and analysis of observations. After the upgrade Posiva's permanent seismic network consists of 17 seismic stations and 21 triaxial sensors. The purpose of the microearthquake measurements at Olkiluoto is to improve understanding of the structure, behaviour and long term stability of the bedrock. The investigation area includes two target areas, of which the larger one, the seismic semi-regional area, includes the Olkiluoto island and its surroundings. The aim is to monitor explosions and tectonic earthquakes in regional scale inside that area. All the expected excavation induced events are assumed to occur inside the smaller target area, the seismic ONKALO block, which is a 2 km x 2 km x 2 km cube surrounding the ONKALO. An additional task of monitoring is related to safeguarding of the construction of the ONKALO.In the beginning the network monitored tectonic earthquakes in order to characterise the undisturbed baseline of seismicity in Olkiluoto. After August 2004, the network also monitored excavation induced seismicity. The first three excavation induced earthquakes were recorded in September 2005. At the moment the total number of excavation induced earthquakes is 17. During the same time about 10 000 excavation blasts were located. The

  4. Olkiluoto biosphere description 2006

    International Nuclear Information System (INIS)

    Haapanen, R.; Aro, L.; Ilvesniemi, H.; Kareinen, T.; Kirkkala, T.; Mykrae, S.; Turkki, H.; Lahdenperae, A.-M.; Ikonen, A.T.K.

    2007-02-01

    This report summarises the current knowledge of the biosphere of Olkiluoto, and it is the first Biosphere Description Report. The elements considered were climate, topography, land use, overburden, terrestrial vegetation and fauna and sea flora, fauna and water. The principal aim was to present a synthesis of the present state (now to 2020) and the main features of past evolution of the biosphere at the site using currently available data. The lack of site specific parameters and their importance was discussed. Conceptual ecosystem models are presented for land and sea. Currently available data made it possible to calculate the biomass of the terrestrial vegetation and further convert it to carbon. In the case of terrestrial animals, preliminary figures are given for moose alone due to lack of sitespecific data. For the same reason, the sea ecosystem model was not quantified within this work. The ecosystems on Olkiluoto do not deviate from the surrounding areas. Since mires are few on Olkiluoto, forests are the most important land ecosystem. However, coastal areas are the transition zones between land and sea, and also potential sites for deep groundwater discharge. The major interest concerning aquatic ecosystems was laid on four future lakes potentially developing from the sea due to the land up-lift. Current sea sediments near Olkiluoto are future land areas, and thus very important. Spatially, the forest ecosystems of Olkiluoto are now most comprehensively covered, while the temporal coverage is highest in sea ecosystems. Lack of data is greatest in terrestrial fauna and sea sediments. During this work, the system boundaries were crossed and the use of data over disciplines was started. The data were mostly in agreement, but some discrepancies were detected. To solve these, and to supplement the existing data, some recommendations were given. (orig.)

  5. Geological site selection studies in Precambrian crystalline rocks in Finland

    International Nuclear Information System (INIS)

    Vuorela, P.

    1988-01-01

    In general geological investigations made since 1977 the Finnish crystalline bedrock has been determined to be suitable for the final disposal of the spent nuclear fuel. Regional investigations have been mainly based on already existing geological studies. Special attention has been paid on the international geological Finland as the Baltic Shield is stiff and stable and situated far outside the zones of volcanic and seismic activity. The present day crustal movements in Finland are related to landuplift process. Movements and possible faults in the bedrock follow fracture zones which devide the bedrock into mosaiclike blocks. As compared to small scale geological maps the bedrock blocks are often indicated as large granite rock formations which are less broken than the surrounding rocks, though the age of granite formations is at least 1500 millions of years. The large bedrock blocks (20-300 km 2 ) are divided to smaller units by different magnitudes of fractures and these smaller bedrock units (5-20 km 2 ) have been selected for further site selection investigations. At the first stage of investigations 327 suitable regional bedrock blocks have been identified on the basis of Landsat-1 winter and summer mosaics of Finland. After two years of investigations 134 investigation areas were selected inside 61 bedrock blocks and classified to four priority classes, the three first of which were redommended for further investigations. Geological criteries used in classification indicated clear differences between the classes one and three, however all classified areas are situated in large rather homogenous bedrock blocks and more exact three dimensional suitability errors may not be observed until deep bore holes have been made

  6. Local seismic network at the Olkiluoto site. Annual report for 2011

    International Nuclear Information System (INIS)

    Saari, J.; Malm, M.

    2012-06-01

    This report gives the results of microseismic monitoring during 2011. Excavation of the underground characterisation facility called ONKALO started in 2004. Before that, in February 2002, Posiva Oy established a local seismic network of six stations on the island of Olkiluoto. After that the number of seismic stations has increased gradually. In 2011 Posiva's permanent seismic network consists of 15 seismic stations and 20 triaxial sensors. The purpose of the microearthquake measurements at Olkiluoto is to improve understanding of the structure, behaviour and long term stability of the bedrock. The investigation area includes two target areas. The larger target area, called seismic semiregional area, covers the Olkiluoto Island and its surroundings. The purpose is to monitor explosions and tectonic earthquakes in regional scale inside that area. The smaller target area is called the seismic ONKALO block, which is a 2 km x 2 km x 2 km cube surrounding ONKALO. It is assumed that all the expected excavation induced events occur within this volume. At the moment the seismic ONKALO block includes ten seismic stations. An additional task of monitoring is related to safeguarding of the construction of ONKALO. The configuration of the seismic network as well as the software packages applied in data processing and analyses have remained during the previous year. The design model of ONKALO and the brittle fault zone model of the Olkiluoto of the seismic visualization package Jdi were upgraded in 2011. The network has operated nearly continuously. There was a 14 minutes and 30 second long operation failure in December 2011. That was the first network operation failure in five years. Altogether 1223 events have been located in the Olkiluoto area, in the reported time period. Most of them (1098) are explosions that occurred inside the seismic semiregional area and especially inside the seismic ONKALO block (1064 events). The magnitudes of the observed explosions inside the semi

  7. Local seismic network at the Olkiluoto site. Annual report for 2011

    Energy Technology Data Exchange (ETDEWEB)

    Saari, J.; Malm, M. [AF-Consult Oy, Espoo (Finland)

    2012-06-15

    This report gives the results of microseismic monitoring during 2011. Excavation of the underground characterisation facility called ONKALO started in 2004. Before that, in February 2002, Posiva Oy established a local seismic network of six stations on the island of Olkiluoto. After that the number of seismic stations has increased gradually. In 2011 Posiva's permanent seismic network consists of 15 seismic stations and 20 triaxial sensors. The purpose of the microearthquake measurements at Olkiluoto is to improve understanding of the structure, behaviour and long term stability of the bedrock. The investigation area includes two target areas. The larger target area, called seismic semiregional area, covers the Olkiluoto Island and its surroundings. The purpose is to monitor explosions and tectonic earthquakes in regional scale inside that area. The smaller target area is called the seismic ONKALO block, which is a 2 km x 2 km x 2 km cube surrounding ONKALO. It is assumed that all the expected excavation induced events occur within this volume. At the moment the seismic ONKALO block includes ten seismic stations. An additional task of monitoring is related to safeguarding of the construction of ONKALO. The configuration of the seismic network as well as the software packages applied in data processing and analyses have remained during the previous year. The design model of ONKALO and the brittle fault zone model of the Olkiluoto of the seismic visualization package Jdi were upgraded in 2011. The network has operated nearly continuously. There was a 14 minutes and 30 second long operation failure in December 2011. That was the first network operation failure in five years. Altogether 1223 events have been located in the Olkiluoto area, in the reported time period. Most of them (1098) are explosions that occurred inside the seismic semiregional area and especially inside the seismic ONKALO block (1064 events). The magnitudes of the observed explosions inside the

  8. A system of nomenclature for rocks in Olkiluoto

    International Nuclear Information System (INIS)

    Mattila, J.

    2006-06-01

    Due to international interest in the Finnish deep repository project at Olkiluoto (SW Finland) and the need for collaboration between scientists involved in site investigations for the disposal of spent nuclear fuel in other countries, a well-documented system of rock nomenclature is required, based on existing classification schemes and international recommendations. The BGS (British Geological Survey) rock classification scheme is the most comprehensive rock classification scheme and the basic principles behind it are utilised for the system of nomenclature for rocks in Olkiluoto. The BGS classification system is based on the use of descriptive names and a clear hierarchy, making it possible to classify rocks at different levels depending on the specific goals of the study, the level of available information, and the expertise of the user. Each rock type is assigned a root name, which is based on structural and textural characteristics or modal compositions of the rock and the root names are refined with qualifier terms as prefixes. Qualifier terms refer to the structure or modal composition of the rock. The bedrock at the Olkiluoto site consists of metamorphic and igneous rocks. The metamorphic rocks consist of migmatitic gneisses and (non-migmatitic) gneisses, which are further divided according to their structural characteristics and modal compositions, the former into stromatic, veined, diatexitic gneisses, the latter into mica, quartz, mafic and TGG gneisses. Igneous rocks consist of pegmatitic granites, K-feldspar porphyry and diabases. (orig.)

  9. Local seismic network at the Olkiluoto site. Annual report for 2010

    International Nuclear Information System (INIS)

    Saari, J.; Malm, M.

    2011-11-01

    Excavation of the underground characterisation facility (the ONKALO) started in 2004. Before that, in February 2002, Posiva Oy established a local seismic network of six stations on the island of Olkiluoto. After that the number of seismic stations has increased gradually. In 2010 Posiva's permanent seismic network consists of 15 seismic stations and 20 triaxial sensors. The purpose of the microearthquake measurements at Olkiluoto is to improve understanding of the structure, behaviour and long term stability of the bedrock. The investigation area includes two target areas. The larger target area, called seismic semiregional area, covers the Olkiluoto Island and its surroundings. The purpose is to monitor explosions and tectonic earthquakes in regional scale inside that area. The smaller target area is called the seismic ONKALO block, which is a 2 km *2 km *2 km cube surrounding the ONKALO. It is assumed that all the expected excavation induced events occur within this volume. At the moment the seismic ONKALO block includes ten seismic stations. An additional task of monitoring is related to safeguarding of the ONKALO. This report gives the results of microseismic monitoring during 2010. In March 2010, the seismic network was upgraded by a new triaxial borehole seismometer in order to improve the sensitivity and the depth resolution inside the ONKALO block. The sensor is the second one inside the ONKALO. New PC for data processing and analysis with the new version of Linux operating system was installed. Also all software packages for data processing and analysis and for visualization were upgraded. The network has operated continuously in 2010. Altogether 1089 events have been located in the Olkiluoto area, in reported time period. Most of them (943) are explosions occurred inside the seismic semi-regional area and especially inside the seismic ONKALO block (895 events). The magnitudes of the observed explosions inside the semi-regional area range from M L = -1

  10. Local seismic network at the Olkiluoto site. Annual report for 2009

    International Nuclear Information System (INIS)

    Saari, J.; Malm, M.

    2010-06-01

    Excavation of the underground characterisation facility (the ONKALO) started in 2004. Before that, in February 2002, Posiva Oy established a local seismic network of six stations on the island of Olkiluoto. After that the number of seismic stations has increased gradually. In 2009 Posiva's seismic network consists of 14 seismic stations and 19 triaxial sensors. The purpose of the microearthquake measurements at Olkiluoto is to improve understanding of the structure, behaviour and long term stability of the bedrock. The investigation area includes two target areas. The larger target area, called seismic semiregional area, covers the Olkiluoto Island and its surroundings. The purpose is to monitor explosions and tectonic earthquakes in regional scale inside that area. The smaller target area is called the seismic ONKALO block, which is a 2 km *2 km *2 km cube surrounding the ONKALO. It is assumed that all the expected excavation induced events occur within this volume. At the moment the seismic ONKALO block includes ten seismic stations. An additional task of monitoring is related to safeguarding of the ONKALO. This report gives the results of microseismic monitoring during 2009. Also the changes in the structure and the operation procedure of the network are described. The upgrades in 2009 are limited to the processing, interpretation and reporting practices. The latest upgrades of the equipment were done in November 2008. The final technical tuning and tests related to the upgrade were done in the beginning of 2009. The network has operated continuously in 2009. Altogether 1256 events have been located in the Olkiluoto area, in reported time period. Most of them (1161) are explosions occurred inside the seismic semi-regional area and especially inside the seismic ONKALO block (1135 events). The magnitudes of the observed events inside the semi-regional area range from ML = -1.5 to ML = 1.6 (ML = magnitude in local Richter's scale). Most of them are explosions. Two

  11. New Reactor Siting in Finland, Hanhikivi Site in Pyhaejoki - STUK preliminary safety assessment

    International Nuclear Information System (INIS)

    Nevalainen, Janne

    2013-01-01

    STUK has performed a preliminary assessment of the Decision-in-Principle on the Fennovoima application. A variety of factors must be considered in the selection of a site, including effects of the site on the plant design and the effects of the plant on the site environment. These include external hazards, both natural and human-induced. Since this is a new site, an extensive siting process is followed, that can include an EIA. A site survey is performed to identify candidate sites, after investigating a large region and rejecting unsuitable sites. The remaining sites are then screened and compared on the basis of safety and other considerations to select one or more preferred sites. Natural hazards include geology, seismology, hydrology and meteorology. Offshore ice will be a particular hazard for this plant, since the site is on average only 1.5 m above sea level. The design basis earthquake corresponds to a return frequency of 100,000 years, with 50 % confidence. The existing sites in southern Finland used a design peak ground acceleration of 0.1 g with the ground response spectrum maximum at 10 Hz. The candidate sites in northern Finland will require a peak ground acceleration of 0.2 g with the ground response spectrum maximum at 25 Hz

  12. Semi-integration of overcoring stress data and review of rock stress data at the Olkiluoto site

    International Nuclear Information System (INIS)

    Ask, D.

    2011-06-01

    This project involves a semi-integration of collected rock stress data at Olkiluoto. The data included in the study involves overcoring and hydraulic fracturing data reported in the 2006 Site Report, supplemented with the additional data gathered since then, measurements for the power plant construction, and measurements in ONKALO. Despite the extensive data, and although the data display a fair correspondence with respect to stress magnitudes between methods, a few discrepancies between methods exist. The discrepancies primarily concern the orientation of the horizontal stresses and the magnitude of maximum horizontal stress. The objective of the study is help answer the remaining discrepancies in the collected data using a semi-integration approach on the overcoring data, i.e. a simplified application of the Integrated Stress Determination Method. The semi-integration involves two steps: (i) a brief re-evaluation of data; and (ii) forced overcoring stress calculations based on constraints derived from the other stress measurement techniques. The overall intension was to force overcoring data, which is the method displaying the largest scatter in results at the Olkiluoto site, to be consistent with a number of constraints that were derived from other stress measurement techniques. This exercise would outline the most probable constraints and in the extension, help identifying a stress model for the site. Regrettably, the results of the semi-integration were not completely satisfactory. The most important factor of this outcome is believed to be the failure to reduce the initial scatter through a re-evaluation. The remaining scatter after re-evaluation is judged too large to represent solely in situ stress variation; hence, measurement related errors are likely still present in the re-evaluated data set. A more in-depth analysis may to some extent decrease the scatter in data, but perhaps more effectively, develop a tool that simultaneously can derive the stress

  13. Environmental aspects of Greenfield NPP site in northern Finland

    International Nuclear Information System (INIS)

    Kopisto, L.

    2015-01-01

    Fennovoima will build a nuclear power plant of 1200 MW at Hanhikivi headland in Pyhaejoki, Northern Finland on the shore of the Baltic Sea. According to the target schedule the plant will produce electricity in 2024. The plant supplier is Rusatom Overseas, subsidiary of the Russian Rosatom. No industrial activity is practiced in the immediate surroundings of the site area and the headland and its surroundings are sparsely populated. The area is in its natural state. This means that all the preparatory and infrastructure works needs to be done before the construction of NPP can start. The environmental and nature conservation aspects have to be taken into consideration in planning, construction and operation of the NPP. Northern location sets some challenges to the design of the power plant. The sea area is normally covered with ice almost half of the year which has to be taken into account in the design of the power plant. But there are also advantages: in winter when the cooling water is cold the efficiency of electricity production is estimated to be exceptionally good, approximately 39 %. Since 2008, Fennovoima has carried out several environmental studies and surveys in the site area and has collected information about the nature conditions on land and in the sea area. The collected environmental data has been utilized in land use planning, environmental impact assessment procedure and in applying for conventional permits. The environmental data can also be used as baseline data. The document is composed of an abstract and the presentation slides

  14. Hydrogeochemical interpretation of the groundwater at the Haestholmen site, Finland

    International Nuclear Information System (INIS)

    Nordstrom, D.K.

    1986-11-01

    This investigation forms a part of the research aimed at marking an assessment of the suitability of rapakivi granite at Haestholmen, an island off the southeastern coast of Finland, for the storage of reactor waste from the Loviisa nuclear power plant. The purpose of this study is to provide preliminary interpretations of the groundwater chemistry based on analyses of groundwater samples taken from several drillholes down to depths of 200 m, as well as other hydrogeological studies made on the site. Chemical analyses of grounfwaters at Haestholmen have demonstrated a fresh-water/saline-water interface at 60-150 m depth, depending on the distance from the coast. The main conclusions from this study are that (1) the saline water has a seawater origin, (2) the saline water is most likely old Baltic seawater from the early to middle Holocene, (3) this seawater has been chemically modified by at least four processes: calcite precipitation, fluorite dissolution and precipitation, Na-K-Mg-Ca cation exchange and sulfate reduction, (4) the saline groundwaters are not chemically uniform with depth and (5) the saline water chemistry reflects a structural control by the bedrock

  15. Baseline conditions at Olkiluoto

    International Nuclear Information System (INIS)

    2003-09-01

    The main purpose of this report is to establish a reference point - defined as the data collected up until the end of year 2002 - for the coming phases of the Finnish spent nuclear fuel disposal programme. The focus is: to define the current surface and underground conditions at the site, both as regards the properties for which a change is expected and for the properties which are of particular interest for long-term safety or environmental impact; to establish, as far as possible, the natural fluctuation of properties that are potentially affected by construction of the underground laboratory, the ONKALO, and to provide references to data on parameters or use in model development and testing and to use models to assist in understanding and interpreting the data. The emphasis of the baseline description is on bedrock characteristics that are relevant to the long-term safety of a spent fuel repository and, hence, to include the hydrogeological, hydrogeochemical, rock mechanical, tectonic and seismic conditions of the site. The construction of the ONKALO will also affect some conditions on the surface, and, therefore, a description of the main characteristics of the nature and the man-made constructions at Olkiluoto is also given. This report is primarily a road map to the available information on the prevailing conditions at the Olkiluoto site and a framework for understanding of data collected. Hence, it refers to numerous available background reports and other archived information produced over the past 20 years or more, and forms a recapitulation and revaluation of the characterisation data of the Olkiluoto site. (orig.)

  16. Regulatory aspects of Olkiluoto 3 nuclear power plant (EPR-1600) (Draft, 12 Sept. 2005)

    International Nuclear Information System (INIS)

    Sandberg, J.; Tiippana, P.

    2005-01-01

    A 1600 MWe European Pressurized Water Reactor (EPR) supplied by the Framatome ANP - Siemens Consortium is under construction at the Olkiluoto site in Finland. Current international safety requirements and especially French and German operating experience have been applied in the design. Finnish requirements and operating experience have also been applied, especially regarding site-specific features. Severe accidentmanagement and protection against a collision of a large passenger airplane are implemented in the plant design. The plant safety features, licensing procedure, Finnish regulatory requirements, changes to the original EPR design, project quality management and regulatory control are discussed. (author)

  17. Eurajoki Olkiluoto birdlife survey 2008

    International Nuclear Information System (INIS)

    Yrjoelae, R.

    2009-02-01

    The study of birds in Olkiluoto in the summer of 2008 repeated the study of the same area conducted in 1997 (Yrjoelae 1997), and was complemented with two new line transect routes and six new waterfowl counting points for the eastern region of the Olkiluoto island. Using this method the research project covered the whole area of the Olkiluoto island. By repeating the earlier routes and counting points it presented an opportunity to clarify any possible changes in the area. A wide variety of different biotypes are evident in the mixed-growth forests of the whole Olkiluoto island and after that are both spruce and pine forests. There are regionally, however, great differences in the division. In the western sector of the island, on the first three lines, the share of industrial areas and the road network are noticeable. The methods used were line transects for the bird species found on the ground and point checks for the aquatic species of birds (Koskimies and Vaeisaenen 1998), which are the established methods used for the monitoring of birdlife in Finland. In these calculations, the bird observations were 1429 altogether, covering 65 species. The results of the checkpoint census for waterfowl are presented in this study. Altogether, 23 species were interpreted in the census for waterfowl as pairs appearing to nest in the area of the checkpoints. The endangered, or other species mentioned in the EU bird directive, sighted in Olkiluoto in summer 2008 are listed in this study. The Redbacked Shrike and Common Chiffchaff were clearly the most common among these species. The birdlife in Olkiluoto is both rather varied and abundant. A few clear tendencies can be distinguished in the changes within the species of birds. Amongst the waterfowl and gulls, the species favouring flourishing watercourses have increased. The species in the outer archipelago, such as the Common Eider and Velvet Scoter have declined compared to 1997. Probably the waders of the archipelago will

  18. Comparison of different extractions of the soil samples OL-FEH914254, OL-FEH917258 and OL-FIP10, Olkiluoto, SW Finland

    International Nuclear Information System (INIS)

    Lahdenperae, A.-M.

    2014-04-01

    The seven different extractions are used to evaluate and compare the element concentrations and solubility both dried/sieved and fresh mineral soil samples OLFEH914254, OL-FEH917258, OL-FIP10 and OL-FIP10 and humus sample OL-FIP10 taken from the Olkiluoto Island in 2010. The study focuses on the key elements assigned top priority in the biosphere assessments: Cl, Cs, I, Mo, Nb, Ni, Se and Sr. The priority grouping of radionuclides is based on their expected relevance for long-term safety using a simple screening evaluation applied on the calculations cases analysed in the biosphere analyses in the safety case studies and the cases to be analysed from the radionuclide transport model. The extractions included: total, aqua regia, NH 4 Ac (pH 4.5) and water leach extractions. The sequential extractions consisted of: exchangeable, acid-soluble/bound to carbonates, bound to Fe-Mn oxides, bound to organic matter and residual fractions, in addition, separate aqua regia extraction was included. Molybdenum, niobium and selenium concentrations were higher in aqua regia extraction than in the total extraction. Aqua regia extractions were analysed by using different methods in two different laboratories, and thus the results are not completely comparable for the most of the elements. In addition, dry and organic matter, pH, cation exchange capacity and grain size distribution were measured. The pH values measured in the deionised water were on average 0.5 units higher than pH values extracted by 0.01 M CaCl 2 . The CEC was significantly higher in the humus sample than in the mineral soil samples. In modelling migration of elements in ecosystems, especially radionuclides, it is used distribution coefficients (K d values) and concentration ratios (CR), both including a component of concentration in the solids. Solubility of different solid elements varies widely depending the used methods and extracts. (orig.)

  19. Review of the GPS deformation monitoring studies commissioned by Posiva Oy on the Olkiluoto, Kivetty and Romuvaara sites, 1994-2000

    International Nuclear Information System (INIS)

    Vermeer, M.

    2002-05-01

    This report reviews the work done by scientists from the Finnish Geodetic Institute at the three sites Olkiluoto, Kivetty and Romuvaara over the years 1994-2000, with a view to detecting and measuring possible local crustal movements by means of geodetic GPS. The work, which consisted of measurements, computations and analysis, was reported in seven technical reports of Posiva Oy. Reviewed was also the work related to the three permanent stations established in these three sites, which have operated as part of the twelve-station national FinnRef network. The conclusion was that on the whole, the work has been performed professionally using state of the art equipment, measurement and analysis techniques by competent and experienced personnel. A number of suggestions for improvement and future work are given, mainly concerning the way the modelling of atmospheric propagation effects was done and how that affects the scale of the network computation, a proposal for monitoring the absolute scale, as well as remarks concerning the regular re-measurement of reserve marker ties, and the importance of continuing monitoring for a full solar activity cycle. The importance of interdisciplinarity is stressed. This review report is an outcome of the Bedrock Movements Investigations Group which supports STUKs regulatory activities related to confirming site investigations at Olkiluoto. (orig.)

  20. Forest soil survey and mapping of the nutrient status of the vegetation on Olkiluoto island. Results from the first inventory on the FEH plots

    International Nuclear Information System (INIS)

    Tamminen, P.; Aro, A.; Salemaa, M.

    2007-09-01

    The aim of the inventory was to determine the status of the forest soils and to map the current nutrient status of forest vegetation on Olkiluoto Island in order to create a basis for monitoring future changes in the forests and to provide data for a biospheric description of the island. The study was carried out on 94 FEH plots, which were selected from the forest extensive monitoring network (FET plots) on the basis of the forest site type distribution and tree stand characteristics measured on the island during 2002 - 2004. Forest soils on Olkiluoto are very young and typical of soils along the Finnish coast, i.e. stony or shallow soils overlying bedrock, but with more nutrients than the forest soils inland. In addition to nutrients, the heavy metal concentrations are clearly higher on Olkiluoto than the average values for Finnish forest soils. The soil in the alder stands growing along the seashore is different from the other soils on Olkiluoto and the control soils inland. These soils are less acidic and have large reserves of sodium, magnesium and nitrogen. Macronutrient concentrations in vascular plant species were relatively similar to those reported for Southern Finland. However, it is obvious that the accumulation of particulate material on the vegetation, especially on forest floor bryophytes, has increased due to emissions derived from the construction of roads, drilling and rock crushing, as well as the other industrial activities on Olkiluoto Island. Leaf and needle analysis indicated that the tree stands had, in the main, a good nutrient status on Olkiluoto Island. The surveying methods used on Olkiluoto are better suited to detect systematic changes over a larger area or within a group of sample plots than the changes on individual plots. (orig.)

  1. Modelling of salt water upconing in Olkiluoto

    International Nuclear Information System (INIS)

    Loefman, J.; Poteri, A.; Pitkaenen, P.

    2010-04-01

    Posiva Oy is preparing for the final disposal of spent nuclear fuel in the crystalline bedrock in Finland. Olkiluoto in Eurajoki has been selected as the primary site for the repository, subject to further detailed characterisation, which is currently focused on the construction of an underground rock characterisation and research facility (the ONKALO). During the repository operation the open tunnels and shafts of the ONKALO, and the subsequent repository, are likely to create a hydraulic disturbance to the site's groundwater system for hundreds of years (the greatest impact concerns only the time of the operational period, i.e., c. 100 years). In particular, during the operational phase of the repository upward flow below the tunnels may give rise to the upconing of deep highly saline groundwater up to the planned repository rock volume, which is a concern with regard to the performance of the tunnel backfill material after the closure of the tunnels. This study concerns the supporting groundwater flow analysis for the Rock Suitability Criteria (RSC) programme, which has been set up to develop host rock requirements for the repository design and layout adaptation. The objective is to assess the potential upconing of deep highly saline groundwater into the planned repository rock volume. The work is divided into three separate sub-tasks: characterization of the expected upconing on the basis of 1) observations in the drillholes, 2) numerical groundwater flow modelling, and 3) the analytic groundwater flow modelling

  2. Seismic VSP Investigations at Olkiluoto, 2005

    Energy Technology Data Exchange (ETDEWEB)

    Enescu, N.; Cosma, C.; Balu, L. (Vibrometric, Vantaa (Finland))

    2007-08-15

    Posiva Oy carries out R and D related tasks for spent nuclear fuel disposal in Finland. The site characterization has been conducted since 1987 in Olkiluoto in western Finland. The ONKALO underground characterization facility has been under construction since 2004. Vibrometric Oy has been contracted to carry out seismic VSP survey in four drillholes in the immediate vicinity of ONKALO, for the characterization of the seismically responsive structures. Four drillholes, KR8, KR27, KR29 and KR38 were included to the project. Seven seismic source locations on ground surface were used for each drillhole. The source locations were optimized with respect to the drillhole and ONKALO and were configured as linear arrays to produce optimum imaging focused on the ONKALO volume. A mechanical Vibsist source, using a hydraulic rock breaker mounted on a 22 t excavator, was used as source of seismic signal. The signal was recorded with downhole 3-component geophones. The recording array was 8-level long, with 5 m spacing between levels. Acquisition was run throughout the drillholes. Processing of the VSP profiles consisted of time decoding of the impact sequences, filtering and image point (IP) transform. The interpretation was carried out interactively, seeking for best match of orientation of each reflection according to different borehole profiles where the features were seen. The interpretations were built as an add-on to a previous seismic model of the site. The most distinct reflectors were interpreted, compiled to as a part of a terrain model composed of 3D surfaces, and transferred digitally together with other results (3D elements of reflector locations) into Posiva's 3D modeling system. Some of the reflectors have already received direct confirmation from ONKALO observations. (orig.)

  3. Seismic VSP Investigations at Olkiluoto, 2005

    International Nuclear Information System (INIS)

    Enescu, N.; Cosma, C.; Balu, L.

    2007-08-01

    Posiva Oy carries out R and D related tasks for spent nuclear fuel disposal in Finland. The site characterization has been conducted since 1987 in Olkiluoto in western Finland. The ONKALO underground characterization facility has been under construction since 2004. Vibrometric Oy has been contracted to carry out seismic VSP survey in four drillholes in the immediate vicinity of ONKALO, for the characterization of the seismically responsive structures. Four drillholes, KR8, KR27, KR29 and KR38 were included to the project. Seven seismic source locations on ground surface were used for each drillhole. The source locations were optimized with respect to the drillhole and ONKALO and were configured as linear arrays to produce optimum imaging focused on the ONKALO volume. A mechanical Vibsist source, using a hydraulic rock breaker mounted on a 22 t excavator, was used as source of seismic signal. The signal was recorded with downhole 3-component geophones. The recording array was 8-level long, with 5 m spacing between levels. Acquisition was run throughout the drillholes. Processing of the VSP profiles consisted of time decoding of the impact sequences, filtering and image point (IP) transform. The interpretation was carried out interactively, seeking for best match of orientation of each reflection according to different borehole profiles where the features were seen. The interpretations were built as an add-on to a previous seismic model of the site. The most distinct reflectors were interpreted, compiled to as a part of a terrain model composed of 3D surfaces, and transferred digitally together with other results (3D elements of reflector locations) into Posiva's 3D modeling system. Some of the reflectors have already received direct confirmation from ONKALO observations. (orig.)

  4. Chlorine isotopes and their application to groundwater dating at Olkiluoto

    International Nuclear Information System (INIS)

    Gascoyne, M.

    2014-09-01

    The chlorine isotopes 36 Cl and 37 Cl have been shown to be useful tracers of groundwater, and for investigations of sources of dissolved Cl, mixing of fluids, water-rock interactions in sedimentary environments and in identifying solute sources and transport mechanisms. In addition, the radioactive isotope, 36 Cl, is a useful tracer for determining the residence time of groundwater. This report examines the results of Cl isotopic analysis of groundwaters from as deep as 1000 m at the Olkiluoto site in southwest Finland. Thirty-four samples were analysed for 36 Cl/Cl and 29 were analysed for 37 Cl (expressed as δ 37 Cl). The value δ 37 Cl was found to stabilize at higher salinities and the maximum range of δ 37 Cl was from about - 0.6 to +0.6 per mille. Because of this limited range and the relatively large error margins associated with the δ 37 Cl measurement, the usefulness of this ratio appears to be limited. Therefore, the main part of this report is largely focused on 36 Cl. Estimation of residence time of 36 Cl gives results that support the presence of at least five groundwater types at Olkiluoto. The consistency of 36 Cl/Cl ratios in groundwaters of several widely separated, deep locations and different rock compositions, suggests that these deeper groundwaters are in secular equilibrium and, therefore, likely to be older than 1.5 million years. (orig.)

  5. Interpretation of aeromagnetic survey in Eurajoensalmi, Olkiluoto (2008)

    International Nuclear Information System (INIS)

    Oehman, I.; Ahokas, T.; Lahti, M.

    2009-06-01

    In 2001, Olkiluoto was selected as the site for the final disposal of spent nuclear waste in Finland. Current construction of the underground research facility, ONKALO, is occurring at the Olkiluoto site. During the past three decades, detailed geological and geophysical investigations have been carried out on Olkiluoto Island and in the Olkiluoto vicinity in order to define its bedrock properties and structures that affect the final nuclear waste disposal. In April 2008, a high resolution aeromagnetic survey was carried out in the Eurajoensalmi inlet in order to investigate the sea and coastal areas north and west of Eurajoensalmi. Measured parameter was total magnetic field. The main goal of the survey was to improve the magnetic image of Eurajoensalmi area, to locate the area's most significant magnetic features, and by magnetic modelling find the best geological explanations for them. Some preliminary lineament interpretations were also performed to compare the accuracy of location data between lineaments interpreted in earlier surveys versus the new 2008 data. Data acquired during earlier magnetic surveys was used as reference data. Interpretation was conducted using measured total magnetic field, derivatives computed from the total field and various visualisation techniques. Comparison of data from the 1988 aeromagnetic survey conducted by GTK and the 2008 survey proves that a more detailed survey configuration sharpens anomalies and increases reliability in the interpretation of subtle features. Positioning techniques have improved significantly since the 1980's, which improves positioning accuracy and increases consistency. It can be concluded that the 2008 data is significantly more detailed and brings interpretation to a new level. Four areas, including well known bedrock structures HZ21, which corresponds to brittle deformation zone OL-BFZ002, and Liikla and Selkaenummi shear zones, were modelled. Modelling was intentionally kept relatively simple using

  6. Strength and strain anisotropy of olkiluoto mica gneiss

    International Nuclear Information System (INIS)

    Hakala, M.; Kuula, H.; Hudson, J.

    2006-10-01

    An anisotropy in the elastic moduli values of intact rock with a ratio of more than 1.3∼1.5 has been reported to have an effect on the calculated magnitudes and orientations of the in situ principal stress components as measured by the overcoring method. Work related to the on-going site investigation for a deep radioactive waste repository at the Olkiluoto site in Western Finland has shown that the migmatic mica gneiss is anisotropic which could therefore affect the interpretation of overcoring stress measurement results. This paper includes a summary of the theory of anisotropy concerning the intact rock moduli via the strain compliance matrix, a description of the core sample testing methods, and interpretation of results for the migmatic mica gneiss from two site investigation boreholes. In this case study, 19 specimens were tested and the results showed a modulus anisotropy of about 1.4. Because such anisotropy is high enough to produce significant errors in the estimation of the in situ principal stresses, it is recommended to take this into account in the interpretation of the stress measurement results, both in the context of the current work in Finland and in other projects where similar anisotropy is encountered. (orig.)

  7. Detailed site characterization for final disposal of spent fuel in Finland - Case study Loviisa

    International Nuclear Information System (INIS)

    Anttila, P.; Ahokas, H.; Ruotsalainen, P.; Cosma, C.; Keskinen, J.; Hinkkanen, H.; Rouhiainen, P.; Oehberg, A.

    1998-01-01

    The spent fuel from the Finnish nuclear power plants will be disposed of in the Finnish bedrock. Pos iva Oy is responsible for the site selection programme carried out in accordance with the governmental decisions. Preliminary site investigations were made in five areas in 1987-1992. Based on the results, three areas, Romuvaara in Kuhmo, Kivetty in Aeaenekoski and Olkiluoto in Eurajoki, were selected for the detailed site characterization in 1993-2000. The final site will be selected by the end of the year 2000. The interim reporting of the detailed studies of the three areas was made in 1996. In 1997, the island of Haestholmen, as the host to the Loviisa NPP, was included as a fourth candidate site in the programme for the detailed site investigations. The goal is to characterize this site also in detail by the end of 2000 to attain the same level of knowledge as available from the three other sites. The background information existing from the studies made for the construction of the repository for the low-and intermediate-level wastes will create a good basis to reach the target. The research programme for the detailed site characterization has mainly been focused on groundwater flow and geochemistry due to their importance in terms of long-term safety of the repository. Equipment and methodology development by Posiva has introduced new tools that provide more accurate data on relevant parameters than the ones used in previous stages of site characterization. The programme also contains studies for additional information of the structural and geological properties of the bedrock towards the depth. Also predictive modelling has been made for evaluating the relevance of the assumptions made. The methods applied in the site characterization have comprised, e.g., geological mapping, deep core drilling, groundwater sampling and analyzing, hydraulic testing and geophysical measurements

  8. Detailed site characterization for final disposal of spent fuel in Finland - Case study Loviisa

    Energy Technology Data Exchange (ETDEWEB)

    Anttila, P. [IVO Power Engineering Ltd. (Finland); Ahokas, H.; Ruotsalainen, P. [Fintact Oy (Finland); Cosma, C.; Keskinen, J. [Vibrometric Oy (Finland); Hinkkanen, H. [Posiva Oy (Finland); Rouhiainen, P. [PRG-Tec Oy (Finland); Oehberg, A. [Saanio and Riekkola Consulting Engineers (Finland)

    1998-09-01

    The spent fuel from the Finnish nuclear power plants will be disposed of in the Finnish bedrock. Pos iva Oy is responsible for the site selection programme carried out in accordance with the governmental decisions. Preliminary site investigations were made in five areas in 1987-1992. Based on the results, three areas, Romuvaara in Kuhmo, Kivetty in Aeaenekoski and Olkiluoto in Eurajoki, were selected for the detailed site characterization in 1993-2000. The final site will be selected by the end of the year 2000. The interim reporting of the detailed studies of the three areas was made in 1996. In 1997, the island of Haestholmen, as the host to the Loviisa NPP, was included as a fourth candidate site in the programme for the detailed site investigations. The goal is to characterize this site also in detail by the end of 2000 to attain the same level of knowledge as available from the three other sites. The background information existing from the studies made for the construction of the repository for the low-and intermediate-level wastes will create a good basis to reach the target. The research programme for the detailed site characterization has mainly been focused on groundwater flow and geochemistry due to their importance in terms of long-term safety of the repository. Equipment and methodology development by Posiva has introduced new tools that provide more accurate data on relevant parameters than the ones used in previous stages of site characterization. The programme also contains studies for additional information of the structural and geological properties of the bedrock towards the depth. Also predictive modelling has been made for evaluating the relevance of the assumptions made. The methods applied in the site characterization have comprised, e.g., geological mapping, deep core drilling, groundwater sampling and analyzing, hydraulic testing and geophysical measurements 23 refs, 4 figs

  9. Environment studies in the Olkiluoto area

    International Nuclear Information System (INIS)

    Ikonen, A.T.K.; Kaapu, J.; Lehtonen, K.; Mattila, J.; Raeisaenen, R.; Turkki, H.; Sauvonsaari, J.

    2003-04-01

    In the report, different aspects of environmental status of the Olkiluoto area, an island with the near-sea in the Finnish coast of the Baltic Sea, are described by five topical papers. Regarding animal-life, Olkiluoto represents a typical seashore area of southwestern Finland dominated by rocky hills and commercial forests. In the literature and interview study of local hunters, locally dominant mammal and bird species are identified. No threatened or endangered mammals species were found on the island, and only few bird species in Olkiluoto have a high conservation value. The sea area off Olkiluoto is rather shallow and the water mixing conditions are favourable. The quality and biological production of the water are affected by the general state of the Bothian Sea, the loading brought by the Eurajoki and Lapinjoki Rivers and local wastewaters. Also the cooling waters from the local nuclear power plant impact the sea environment. The bottom vegetation varies from an algae-dominant to a vascular-plantdominant community. Amount of benthic fauna and its species composition has varied considerably, due to both variations of the quality of the bottom and eutrophication. The Eurajoki River represents the second largest river system in southwestern Finland. At its upper reaches, the river is classified as clean and suitable for recreational use. Intermittently, additional waters rich in nutrients flow into the river from ditches and tributaries. Diffuse pollution and the wastewaters of riverside municipalities and industry affect on the water of the lower course, where it is only mildly contaminated, hygienically fairly good and satisfactory for recreational use. The benthic fauna of the river is composed of oligochaetes, clams, leeches and larvae. The fish reserve is versatile in places due to stocking. The Eurajoensalmi Strait, the inlet of the river, is a transitional zone between the river and further sea environments. In the offshore area facing Olkiluoto, there

  10. Site-selection studies for final disposal of spent fuel in Finland

    International Nuclear Information System (INIS)

    Vuorela, P.; Aeikaes, T.

    1984-02-01

    In the management of waste by the Industrial Power Company Ltd. (TVO) preparations are being made for the final disposal of unprocessed spent fuel into the Finnish bedrock. The site selection program will advance in three phases. The final disposal site must be made at the latest by the end of the year 2000, in accordance with a decision laid down by the Finnish Government. In the first phase, 1983-85, the main object is to find homogeneous stable bedrock blocks surrounded by fracture zones located at a safe distance from the planned disposal area. The work usually starts with a regional structural analysis of mosaics of Landsat-1 winter and summer imagery. Next an assortment of different maps, which cover the whole country, is used. Technical methods for geological and hydrogeological site investigations are being developed during the very first phase of the studies, and a borehole 1000 meters deep will be made in southwestern Finland. Studies for the final disposal of spent fuel or high-level reprocessing waste have been made since 1974 in Finland. General suitability studies of the bedrock have been going on since 1977. The present results indicate that suitable investigation areas for the final disposal of highly active waste can be found in Finland

  11. Economics of nuclear power in Finland

    International Nuclear Information System (INIS)

    Tarjanne, Risto; Luostarinen, Kari

    2002-01-01

    The nuclear power generation fits perfectly with the long duration load profile of the Finnish power system. The good performance of the Finnish nuclear power has yielded benefits also to the consumers through its contribution to decreasing the electricity price. Furthermore, the introduction of nuclear power has resulted in a clear drop in carbon dioxide emissions from electricity generation in the shift of 1970's and 1980's. In the year 2001 the four Finnish nuclear power units at Loviisa and Olkiluoto generated 22.8 TWh electricity, equivalent to 28 per cent of the total consumption. Loviisa power station has a net output capacity of 2 x 488 MW, and Olkiluoto 2 x 840 MW. The capacity factors of the four nuclear units have been above 90 per cent, which are among the highest in the world. The energy-intensive process industries in particular have strong belief in nuclear power. In November 2000, Teollisuuden Voima company (TVO) submitted to the Finnish Government an application for decision in principle concerning the construction of a new nuclear power plant unit. The arguments were among other things to guarantee for the Finnish industry the availability of cheap electric energy and to meet the future growth of electricity consumption in Finland. The carbon-free nuclear power also represents the most efficient means to meet the Greenhouse Gas abatement quota of Finland. Simultaneously, the energy policy of the Government includes intensive R and D and investment support for the renewable energy sources and energy conservation, and the objective is also to replace coal with natural gas as much as reasonably possible. The fifth nuclear unit would be located in one of the existing Finnish nuclear sites, i.e. Olkiluoto or Loviisa. The size of the new nuclear unit would be in the range of 1000 to 1600 MW electric. The ready infrastructure of the existing site could be utilised resulting in lower investment cost for the new unit. The Finnish Government accepted the

  12. Gefinex 400S (Sampo) EM-soundings at Olkiluoto 2008

    International Nuclear Information System (INIS)

    Jokinen, T.; Lehtimaeki, J.

    2008-09-01

    In the beginning of June 2008 Geological Survey of Finland (GTK) carried out electromagnetic frequency soundings with Gefinex 400S equipment (Sampo) in the vicinity of ONKALO at the Olkiluoto site investigation area. The same soundings sites were first time measured and marked in 2004 and has been repeated after it yearly in the same season. The aim of the measurements is to monitor the changes of groundwater conditions by the changes of the electric conductivity of the earth at ONKALO and repository area. The measurements form two 1400 m long broadside profiles, which have 200 m mutual distance and 200 m station separation. The profiles have been measured using 200, 500, and 800 m coil separations. Because of the strong electromagnetic noise all planned sites (48) could not be measured. In 2008 the measurements were performed at the sites that were successful in 2007 (43 soundings). The numerous power lines and cables in the area generate local disturbances on the sounding curves, but the signal/noise also with long coil separations and the repeatability of the results is reasonably good. However, most suitable for monitoring purposes are the sites without strong surficial 3D effects. Comparison of the results of 2004 to 2008 surveys shows differences on some ARD (Apparent resistivity-depth) curves. Those are mainly results of the modified man-made structures. The effects of changes in groundwater conditions are obviously slight. (orig.)

  13. Environmental impact assessments of a fifth nuclear power plant unit in Finland

    International Nuclear Information System (INIS)

    Aurela, Jorma; Koivisto, Katarina

    2000-01-01

    This paper presents the results of president questionnaires and media monitoring of press cuttings concerned with siting of the new fifth in a row Finnish NPP. Two years ago both Fortum Power and Heat Oy and Teollisuuden Voima Oy (TVO) launched their Environmental impact assessment (EIA) procedures of a new nuclear power unit in Finland. The EIA procedures were launched to investigate the environmental impacts of a fifth nuclear power plant which possibly will be built in Loviisa or at Olkiluoto. In Finland there are four operating NPP units, two in Loviisa (Fortum) and two in Eurajoki, Olkiluoto (TVO). In the EIA procedure citizens and various associations and authorities have an opportunity to express their views on the matters related to the project. The Ministry of Trade and Industry (MTI) as the coordination authority arranges the organisation of the EIA hearings and the collection of statements and opinions. The EIA procedure in Finland takes place in two stages. The first stage i.e. the EIA programme describes the project and presents the plan on how the environmental effects are investigated and assessed. In the second stage the actual assessment of the environmental effects of the project will be submitted. Both Fortum and Teollisuuden Voima Oy (TVO) launched in spring 1998 their EIA procedures. The main alternatives are the Loviisa 3 project includes two plant type alternatives. The size of the plant is between 1000 and 1700 MWe, and the extension project of the Olkiluoto NPP to build a NPP unit of about 1000-1500 MWe at Olkiluoto. The EIA reports were submitted to the MTI in August 1999 and after that they were on display for two months for opinions and statements

  14. Results of monitoring at Olkiluoto in 2010 - Environment

    International Nuclear Information System (INIS)

    Haapanen, A.

    2011-10-01

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2010. These summary reports have been published since 2005. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground rock characterization facility. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). Monitoring has been carried out for varying periods of time depending on the sector: some monitoring activities performed by TVO originate from the 1970s and the repository-related environmental monitoring of Olkiluoto from the early 2000s. The monitoring programme evolves according to experiences gained from the modelling work and increased understanding of the site. Augmentations in 2010 include one previously unmonitored private drilled well, and sampling of crop plants, aquatic macrophytes, and bottom fauna, as well as soil and water in order to obtain more data on site-specific concentration ratios. In addition to Olkiluoto Island, two so called reference lakes have been included in the sampling. Studies have been going on on one reference mire, as well. Bottom fauna studies of River Eurajoki exist from late 1970s, but have not been presented here before. Dust produced during construction of the third nuclear power unit (OL3), ONKALO and related infrastructure can be seen in the analysis results of needle litter. The construction works and road traffic have a raising effect on the noise levels of the immediate surroundings. The land-use continues to change, but the remaining natural environment resembles other coastal locations. The young age of the soils and the closeness of the sea are reflected in the soil properties. Mammalian fauna on the island is typical of coastal areas in

  15. Results of monitoring at Olkiluoto in 2010 - Environment

    Energy Technology Data Exchange (ETDEWEB)

    Haapanen, A. (ed.) [Haapanen Forest Consulting, Vanhakylae (Finland)

    2011-10-15

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2010. These summary reports have been published since 2005. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground rock characterization facility. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). Monitoring has been carried out for varying periods of time depending on the sector: some monitoring activities performed by TVO originate from the 1970s and the repository-related environmental monitoring of Olkiluoto from the early 2000s. The monitoring programme evolves according to experiences gained from the modelling work and increased understanding of the site. Augmentations in 2010 include one previously unmonitored private drilled well, and sampling of crop plants, aquatic macrophytes, and bottom fauna, as well as soil and water in order to obtain more data on site-specific concentration ratios. In addition to Olkiluoto Island, two so called reference lakes have been included in the sampling. Studies have been going on on one reference mire, as well. Bottom fauna studies of River Eurajoki exist from late 1970s, but have not been presented here before. Dust produced during construction of the third nuclear power unit (OL3), ONKALO and related infrastructure can be seen in the analysis results of needle litter. The construction works and road traffic have a raising effect on the noise levels of the immediate surroundings. The land-use continues to change, but the remaining natural environment resembles other coastal locations. The young age of the soils and the closeness of the sea are reflected in the soil properties. Mammalian fauna on the island is typical of coastal

  16. Visualization and interpretation of the year 2004 mise-a-la-masse survey data at Olkiluoto site

    International Nuclear Information System (INIS)

    Lehtonen, T.

    2006-01-01

    This report concerns mise-a-la-masse surveys conducted from late autumn 2004 to early winter 2005 at the area of the underground characterisation facility (Onkalo) and surroundings. Surveys were made in 21 boreholes and at 6 ground survey areas. Suomen Malmi Oy conducted the fieldwork. Astrock Oy supervised field surveys and processed, interpreted and reported acquired data for Posiva Oy. The purpose of the study was to collect data for geological modelling with following continuity of the conducting features in bedrock from borehole to borehole and to ground surface. These conducting features in bedrock are often linked with lithologic characters or weakness zones. A basis for the current survey was the previous mine-a-la-masse measurements and their results. Current earthings were placed in 26 electrically conducting structures in 8 boreholes and in one outcrop. Current earthings were situated in boreholes KR4, KR7, KR8, KR25, KR27, KR28, KR29 and KR33. Electrical connections were probed in 22 boreholes and at 6 ground survey areas. The acquired survey data were collected to xyz-coordinate oriented databases for 3D processing, interpreting and visualization of the results. At first the data were transferred to Oasis Montaj, where the potential field profiles were drawn and studied borehole-by-borehole current earthing at a time to determine characteristics of the electrical connections. Next were constructed probable connections between boreholes and moved to SurpacVision for visualisation. They were delivered for Posiva Oy as Surpac string and DTM files. With the mise-a-la-masse data, it was possible to determine numerous low dipping electrically conducting structures. Ground surveys were hampered strongly by electrical disturbances of the infrastructure of the Olkiluoto. Results of the all surveys are also collected in the same table, where every one of connections is classified. Interpretations are merely based on mise-a-la-masse data. (orig.)

  17. Visualization and interpretation of the year 2005 mise-a-la-masse survey data at Olkiluoto site

    International Nuclear Information System (INIS)

    Lehtonen, T.

    2006-06-01

    This report concerns mise-a-la-masse surveys conducted autumn 2005 at the area of the underground characterisation facility (Onkalo) and surroundings. Surveys were made in 14 boreholes and at 1 ground survey area. Suomen Malmi Oy conducted the fieldwork. Astrock Oy supervised field surveys and processed, interpreted and reported acquired data for Posiva Oy. The purpose of the study was to collect data for geological modelling with following continuity of the conducting features in bedrock from borehole to borehole and to ground surface. These conducting features in bedrock are often linked with lithologic characters or weakness zones. A basis for the current survey was the previous mine-a-la-masse measurements and their results. Current earthings were placed in 15 electrically conducting structures in 8 boreholes and in one outcrop. Current earthings were situated in boreholes KR4, KR7, KR25, KR27 and KR37. Electrical connections were probed in 14 boreholes and at 1 ground survey area. The acquired survey data were collected to xyz-coordinate oriented databases for 3D processing, interpreting and visualization of the results. At first the data were transferred to Oasis Montaj, where the potential field profiles were drawn and studied borehole-by-borehole current earthing at a time to determine characteristics of the electrical connections. Next probable connections between boreholes and moved were constructed and moved to SurpacVision for visualisation. They were delivered for Posiva Oy as Surpac string and DTM files. With the mise-a-la-masse data, it was possible to determine numerous low dipping electrically conducting structures. Additionally previously detected conducting structures were updated with the observations and interpretations. Ground surveys were hampered strongly by electrical disturbances of the infrastructure of the Olkiluoto. Results of the all surveys are also collected in the same table, where every one of connections is classified

  18. Safety case for the disposal of spent nuclear fuel at Olkiluoto. Complementary considerations 2012

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-12-15

    Complementary Considerations sits within Posiva Oy's Safety Case 'TURVA-2012' report portfolio and has the objective of enhancing confidence in the outcomes of the safety assessment for a spent nuclear fuel repository to be constructed at Olkiluoto, Finland. The main emphasis in this report is on the evidence and understanding that can be gained from observations at the site, including its regional geological environment, and from natural and anthropogenic analogues for the repository, its components and the processes that affect safety. In particular, the report addresses diverse and less quantifiable types of evidence and arguments that are enclosed to enhance confidence in the outcome of the safety assessment. These complementary considerations have been described as evaluations, evidence and qualitative supporting arguments that lie outside the scope of the other reports of the quantitative safety assessment. The experience with natural analogues for the long-term durability of the materials involved and the extent of processes provides high confidence in our understanding of the disposal system and its evolution. For each engineered barrier and key process, there is increasing analogue evidence to support the conceptual models and parameters. Regarding the suitability of the Olkiluoto site to host a spent fuel repository, a number of factors have been identified that indicate the suitability of crystalline host rock in general, and that of the Olkiluoto site in particular. The report also provides radiation background information for the use of complementary indicators, which aid in putting the results of the safety analysis presented in Assessment of Radionuclide Release Scenarios for the Repository System and Biosphere Assessment in a broader perspective to show that the radiation originating from a spent nuclear fuel repository remains in most cases much below natural background radiation or that caused by non-nuclear industries. (orig.)

  19. Safety case for the disposal of spent nuclear fuel at Olkiluoto. Complementary considerations 2012

    International Nuclear Information System (INIS)

    2012-12-01

    Complementary Considerations sits within Posiva Oy's Safety Case 'TURVA-2012' report portfolio and has the objective of enhancing confidence in the outcomes of the safety assessment for a spent nuclear fuel repository to be constructed at Olkiluoto, Finland. The main emphasis in this report is on the evidence and understanding that can be gained from observations at the site, including its regional geological environment, and from natural and anthropogenic analogues for the repository, its components and the processes that affect safety. In particular, the report addresses diverse and less quantifiable types of evidence and arguments that are enclosed to enhance confidence in the outcome of the safety assessment. These complementary considerations have been described as evaluations, evidence and qualitative supporting arguments that lie outside the scope of the other reports of the quantitative safety assessment. The experience with natural analogues for the long-term durability of the materials involved and the extent of processes provides high confidence in our understanding of the disposal system and its evolution. For each engineered barrier and key process, there is increasing analogue evidence to support the conceptual models and parameters. Regarding the suitability of the Olkiluoto site to host a spent fuel repository, a number of factors have been identified that indicate the suitability of crystalline host rock in general, and that of the Olkiluoto site in particular. The report also provides radiation background information for the use of complementary indicators, which aid in putting the results of the safety analysis presented in Assessment of Radionuclide Release Scenarios for the Repository System and Biosphere Assessment in a broader perspective to show that the radiation originating from a spent nuclear fuel repository remains in most cases much below natural background radiation or that caused by non-nuclear industries. (orig.)

  20. Safety case for the disposal of spent nuclear fuel at Olkiluoto. Complementary considerations 2012

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-12-15

    Complementary Considerations sits within Posiva Oy's Safety Case 'TURVA-2012' report portfolio and has the objective of enhancing confidence in the outcomes of the safety assessment for a spent nuclear fuel repository to be constructed at Olkiluoto, Finland. The main emphasis in this report is on the evidence and understanding that can be gained from observations at the site, including its regional geological environment, and from natural and anthropogenic analogues for the repository, its components and the processes that affect safety. In particular, the report addresses diverse and less quantifiable types of evidence and arguments that are enclosed to enhance confidence in the outcome of the safety assessment. These complementary considerations have been described as evaluations, evidence and qualitative supporting arguments that lie outside the scope of the other reports of the quantitative safety assessment. The experience with natural analogues for the long-term durability of the materials involved and the extent of processes provides high confidence in our understanding of the disposal system and its evolution. For each engineered barrier and key process, there is increasing analogue evidence to support the conceptual models and parameters. Regarding the suitability of the Olkiluoto site to host a spent fuel repository, a number of factors have been identified that indicate the suitability of crystalline host rock in general, and that of the Olkiluoto site in particular. The report also provides radiation background information for the use of complementary indicators, which aid in putting the results of the safety analysis presented in Assessment of Radionuclide Release Scenarios for the Repository System and Biosphere Assessment in a broader perspective to show that the radiation originating from a spent nuclear fuel repository remains in most cases much below natural background radiation or that caused by non-nuclear industries. (orig.)

  1. Gefinex 400S (Sampo) EM-Soundings at Olkiluoto 2007

    International Nuclear Information System (INIS)

    Jokinen, T.; Lehtimaeki, J.

    2007-09-01

    In the beginning of June 2007 Geological Survey of Finland carried out electromagnetic frequency soundings with Gefinex 400S equipment (Sampo) at Onkalo situated in Olkiluoto nuclear power plant area. The same soundings sites were the first time measured and marked in 2004 and repeated after it yearly. The aim of the measurements is to monitor the changes of groundwater conditions by the changes of the electric conductivity of the earth at ONKALO and repository area. The measurements form two 1400 m long broadside profiles, which have 200 m mutual distance and 200 m station separation. The profiles have been measured using 200, 500, and 800 m coil separations. The total number of the soundings stations is 48. In 2007 at 8 sounding stations the transmitter and/or receiver sites were changed and the line L11.400 was substituted by line L11.500. Some changes helped but anyway there were 6 stations that could not be measured because of the strong electromagnetic noise. The numerous power lines and the cables of the area generate local 3-D effects on the sounding curves, but the repeatability of the results is good. However, most suitable for monitoring purposes are the sites without strong 3-D effects. Comparison of results 2004-2007 shows small differences at some sounding sites. (orig.)

  2. Difference flow and electrical conductivity measurements at the Olkiluoto site in Eurajoki, drillholes OL-PP66 - OL-PP69

    International Nuclear Information System (INIS)

    Poellaenen, J.

    2009-04-01

    The Posiva Flow Log, Difference Flow Method (PFL DIFF) uses a flowmeter that incorporates a flow guide and can be used for relatively quick determinations of hydraulic conductivity and hydraulic head in fractures/fractured zones in cored drillholes. This report presents the principles of the method and the results of measurements carried out in drillholes OL-PP66, OL-PP67, OL-PP68 and OL-PP69 at the Olkiluoto investigation site in August 2008. All the drillholes discussed in this report are ground holes. The same measuring programme was employed in all four drillholes. The section length of the flow guide was either 2 m or 0.5 m. Flow into the drillhole or from the drillhole to the bedrock was measured within the section lengths and carried out in both pumped and natural (i.e. un-pumped) conditions. Calculations of the transmissivity (T) and the hydraulic head (h) of the zones are shown in the results. The device used includes a sensor for single point resistance (SPR). SPR was measured in connection with flow measurements. The electrical conductivity (EC) of fracture-specific water was measured in chosen fractures in some of the drillholes. Fractures were selected on the basis of the measured flow from fracture to drillhole. The EC of the drillhole water was also measured. (orig.)

  3. Completed lineament interpretation of the Olkiluoto region

    International Nuclear Information System (INIS)

    Paananen, M.

    2013-10-01

    Site characterization activities at Olkiluoto have been taking place for c. 25 years, including a wide range of different geophysical survey methods using various geometries and scales of investigation. The measurements have been done from the air, ground surface, shallow and deep drillholes and the ONKALO underground facility. As a part of the complementary site investigations, two low-altitude geophysical airborne survey campaigns were done around and at Olkiluoto in 2008 and 2009. The survey in 2008 was focused in the Eurajoensalmi area N or NE of Olkiluoto Island. The survey in 2009 covered most of the Olkiluoto Island, the neighbouring sea area and the archipelago W, SW and S of Olkiluoto as well as some of the mainland area SE of Olkiluoto. This report presents a new lineament interpretation based on these new geophysical airborne surveys. For the interpretation work, the data were extensively further processed into different gradients and filtered data sets and maps. Furthermore, the potential of automatic curvature analyses was examined. Also, quantitative profile interpretation was done from a number of profiles to find out the dips and exact locations of the contacts of some features. The qualitative interpretation of the lineaments was carried out by visually inspecting the different versions of the geophysical maps and by digitizing the geometry of each interpreted lineament. The lineaments are collated into two ArcGIS themes (one for magnetic and one for EM lineaments), accompanied by an attribute table that includes a number of attributes for each interpreted feature: lineament identifier, reference to the data used in interpretation, uncertainty, length, average orientation and probable geological character. The total number of new interpreted features is 125 magnetic and 33 electromagnetic lineaments. The main trend of the interpreted features varies between WNW-ESE and NNW-SSE. Furthermore, trends in directions almost N-S and E-W are also

  4. Completed lineament interpretation of the Olkiluoto region

    Energy Technology Data Exchange (ETDEWEB)

    Paananen, M. [Geological Survey of Finland, Espoo (Finland)

    2013-10-15

    Site characterization activities at Olkiluoto have been taking place for c. 25 years, including a wide range of different geophysical survey methods using various geometries and scales of investigation. The measurements have been done from the air, ground surface, shallow and deep drillholes and the ONKALO underground facility. As a part of the complementary site investigations, two low-altitude geophysical airborne survey campaigns were done around and at Olkiluoto in 2008 and 2009. The survey in 2008 was focused in the Eurajoensalmi area N or NE of Olkiluoto Island. The survey in 2009 covered most of the Olkiluoto Island, the neighbouring sea area and the archipelago W, SW and S of Olkiluoto as well as some of the mainland area SE of Olkiluoto. This report presents a new lineament interpretation based on these new geophysical airborne surveys. For the interpretation work, the data were extensively further processed into different gradients and filtered data sets and maps. Furthermore, the potential of automatic curvature analyses was examined. Also, quantitative profile interpretation was done from a number of profiles to find out the dips and exact locations of the contacts of some features. The qualitative interpretation of the lineaments was carried out by visually inspecting the different versions of the geophysical maps and by digitizing the geometry of each interpreted lineament. The lineaments are collated into two ArcGIS themes (one for magnetic and one for EM lineaments), accompanied by an attribute table that includes a number of attributes for each interpreted feature: lineament identifier, reference to the data used in interpretation, uncertainty, length, average orientation and probable geological character. The total number of new interpreted features is 125 magnetic and 33 electromagnetic lineaments. The main trend of the interpreted features varies between WNW-ESE and NNW-SSE. Furthermore, trends in directions almost N-S and E-W are also

  5. Visualisation and interpretation of the autumn 2006 mise-a-la-masse survey data at the Olkiluoto site

    International Nuclear Information System (INIS)

    Lehtonen, T.

    2007-01-01

    previous surveys. The best electrical connections from current earthings in drillholes OL-KR4 and OL-KR27 were found to drillhole OL-KR40. Drillholes OL-KR41, OL-KR42 and OL-KR43 are too remotely situated for reliable interpretations. Ground surveys were hampered strongly by electrical disturbances of the infrastructure in the Olkiluoto. Results of the all surveys are also collected in the same table, where every one of connections is classified. Interpretations are merely based on mise-a-la-masse data. (orig.)

  6. GPS operations at Olkiluoto in 2011

    Energy Technology Data Exchange (ETDEWEB)

    Koivula, H.; Kallio, U.; Nyberg, S.; Jokela, J.; Poutanen, M. [Finnish Geodetic Institute, Masala (Finland)

    2012-06-15

    The Finnish Geodetic Institute has studied crustal deformations at Olkiluoto, Kivetty and Romuvaara in co-operation with Posiva Oy since 1995. At Olkiluoto a total of 32 GPS campaigns have been carried out at inner network since 1995 and 17 campaigns at outer network since 2003. Kivetty and Romuvaara were not measured in 2011. In the Olkiluoto inner network 80 percent of the estimated change rates are smaller than 0.10 mm/a. One third of the change rates are statistically significant. They are mainly related to the Olkiluoto permanent station (GPS1) and to the pillars GPS6 and GPS13. The change rates related to GPS6 are not realistic due to the site-specific changes affecting the time series. The maximum change rate (-0.20 mm/a {+-} 0.05 mm/a) is related to GPS13. The time series of GPS13 is half the length of other pillars and therefore, the change rates are more uncertain. In the Olkiluoto outer network the maximum and statistically significant change rate is between GPS1-GPS11 (0.39 mm/a {+-} 0.06 mm/a). Pillar GPS12 was not observed this year. The change rates of baselines GPS1-GPS14 and GPS1-GPS15 are first time statistically significant. The change rates indicate a small movement of the GPS1 pillar. The baseline GPS1-GPS11 crosses an old fracture zone locating in the direction of the Eurajoensalmi, which might be a reason for the deformation. On the other hand, the Onkalo excavations in the vicinity of the Olkiluoto permanent station (GPS1) may cause some movement. Electronic distance measurements have been performed at Olkiluoto at the baseline GPS7-GPS8 using the Mekometer since 2002. The measurements have been carried out simultaneously with GPS campaigns. Based on 19 measurements in 10 years, the trends of the two time series seems to be similar. Due to unmodelled or dismodelled geometrical offsets and the scale difference between GPS measurements and EDM there is about 0.3 mm difference between distances GPS7-GPS8 derived from GPS measurements and EDM

  7. GPS operations at Olkiluoto in 2011

    International Nuclear Information System (INIS)

    Koivula, H.; Kallio, U.; Nyberg, S.; Jokela, J.; Poutanen, M.

    2012-06-01

    The Finnish Geodetic Institute has studied crustal deformations at Olkiluoto, Kivetty and Romuvaara in co-operation with Posiva Oy since 1995. At Olkiluoto a total of 32 GPS campaigns have been carried out at inner network since 1995 and 17 campaigns at outer network since 2003. Kivetty and Romuvaara were not measured in 2011. In the Olkiluoto inner network 80 percent of the estimated change rates are smaller than 0.10 mm/a. One third of the change rates are statistically significant. They are mainly related to the Olkiluoto permanent station (GPS1) and to the pillars GPS6 and GPS13. The change rates related to GPS6 are not realistic due to the site-specific changes affecting the time series. The maximum change rate (-0.20 mm/a ± 0.05 mm/a) is related to GPS13. The time series of GPS13 is half the length of other pillars and therefore, the change rates are more uncertain. In the Olkiluoto outer network the maximum and statistically significant change rate is between GPS1-GPS11 (0.39 mm/a ± 0.06 mm/a). Pillar GPS12 was not observed this year. The change rates of baselines GPS1-GPS14 and GPS1-GPS15 are first time statistically significant. The change rates indicate a small movement of the GPS1 pillar. The baseline GPS1-GPS11 crosses an old fracture zone locating in the direction of the Eurajoensalmi, which might be a reason for the deformation. On the other hand, the Onkalo excavations in the vicinity of the Olkiluoto permanent station (GPS1) may cause some movement. Electronic distance measurements have been performed at Olkiluoto at the baseline GPS7-GPS8 using the Mekometer since 2002. The measurements have been carried out simultaneously with GPS campaigns. Based on 19 measurements in 10 years, the trends of the two time series seems to be similar. Due to unmodelled or dismodelled geometrical offsets and the scale difference between GPS measurements and EDM there is about 0.3 mm difference between distances GPS7-GPS8 derived from GPS measurements and EDM. It is

  8. Gefinex 400S (Sampo) EM-Soundings at Olkiluoto 2006

    International Nuclear Information System (INIS)

    Jokinen, T.; Lehtimaeki, J.

    2006-08-01

    In the beginning of summer 2006 Geological Survey of Finland carried out electromagnetic frequency soundings with Gefinex 400S equipment (called also Sampo) at Onkalo situated in Olkiluoto nuclear power plant area. The same soundings sites were the first time measured and marked in 2004 and repeated in 2005. The aim of the measurements is to monitor the changes of groundwater conditions by the changes of the electric conductivity of the earth at ONKALO and repository area. The measurements form two 1400 m long broadside profiles, which have 200 m mutual distance and 200 m station separation. The profiles have been measured using 200, 500, and 800 m coil separations. The total number of the soundings was 48 but at 8 stations the measurement did not succeed because of strong electromagnetic noise. The numerous power lines and the cables of the area generate local 3-D effects on the sounding curves, but the repeatability of the results is good. However, most suitable for monitoring purposes are the sites without strong 3-D effects. Comparison of results 2004-2006 shows small differences at some sounding sites. (orig.)

  9. Uranium mineral - groundwater equilibrium at the Palmottu natural analogue study site, Finland

    International Nuclear Information System (INIS)

    Ahonen, L.; Ruskeeniemi, T.; Blomqvist, R.; Ervanne, H.; Jaakkola, T.

    1993-01-01

    The redox-potential, pH, chemical composition of fracture waters, and uraninite alteration associated with the Palmottu uranium mineralization (a natural analogue study site for radioactive waste disposal in southwestern Finland), have been studied. The data have been interpreted by means of thermodynamic calculations. The results indicate equilibrium between uraninite, ferric hydroxide and groundwater in the bedrock of the study site. Partially oxidized uraninite (UO 2 .33) and ferric hydroxide are in equilibrium with fresh, slightly acidic and oxidized water type, while primary uraninite is stable with deeper waters that have a higher pH and lower Eh. Measured Eh-pH values of groundwater cluster within a relatively narrow range indicating buffering by heterogenous redox-processes. A good consistency between measured Eh and analyzed uranium oxidation states was observed

  10. Impact of peatland restoration on nutrient and carbon leaching from contrasting sites in southern Finland

    Science.gov (United States)

    Vasander, Harri; Sallantaus, Tapani; Koskinen, Markku

    2010-05-01

    Impacts of peatland restoration on nutrient and carbon leaching from contrasting sites in southern Finland Tapani Sallantaus1, Markku Koskinen2, Harri Vasander2 1)Finnish Environment Institute, Biodiversity unit, Box 140, FIN-00251 Helsinki, Finland, tapani.sallantaus@ymparisto.fi 2)Department of Forest Sciences, University of Helsinki, Box 27, FIN-00014 University of Helsinki, Finland, markku.koskinen@helsinki.fi, harri.vasander@helsinki.fi Less than 20 % of the original mire area of southern Finland is still in natural state. Even many peatlands in today's nature conservation areas had been partly or totally drained before conservation. Until now, about 15000 ha of peatlands have been restored in conservation areas. Here we present data concerning changes in leaching due to restoration in two contrasting areas in southern Finland. The peatlands in Seitseminen have originally been fairly open, growing stunted pine, and unfertile, either bogs or poor fens. The responses of tree stand to drainage in the 1960s were moderate, and the tree stand before restoration was about 50 m3/ha, on average. The trees were partly harvested before filling in the ditches mainly in the years 1997-1999 . The peatlands of Nuuksio are much more fertile than those in Seitseminen, and had greatly responded to drainage, which took place already in the 1930s and 1950s. The tree stand consisted mainly of spruce and exceeded 300 m3/ha in large part of the area. The ditches were dammed in the autumn 2001 and the tree stand was left standing. Runoff water quality was monitored in three basins in both areas. To obtain the leaching rates, we used simulated runoff data obtained from the Finnish Environment Institute, Hydrological Services Division. The responses in leaching were in the same direction in both cases. However, especially when calculated per restored hectare (Table 1), the responses were much stronger in the more fertile areas of Nuuksio for organic carbon and nitrogen, but not so much

  11. Microbiology of Olkiluoto Groundwater 2004 - 2006

    International Nuclear Information System (INIS)

    Pedersen, K.

    2008-02-01

    The microbiology of shallow and deep groundwater in Olkiluoto, Finland, was analysed for almost three years from 2004 to 2006. The extensive sampling and analysis programme produced a substantial database, including 60 analytical datasets on the microbiology of Olkiluoto groundwater, which is described and interpreted here. One part of this database comprises 39 complete analytical datasets on microbiology, chemistry, and dissolved gas composition assembled on four sampling campaigns from measurements from 16 shallow observation tubes and boreholes ranging in depth from 3.5 to 24.5 m. The second part of the database contains 21 datasets on microbiology and chemistry covering 13 deep boreholes ranging in depth from 35 to 450 m. In addition, the database contains 33 completed analyses of gas covering 14 deep boreholes ranging in depth from 40 to 742 m. Most of these analyses were completed before the onset of ONKALO construction, and the remaining samples were collected before ONKALO construction had extended below a depth of 100 m; therefore, this dataset captures the undisturbed conditions before the building of ONKALO. Shallow groundwater in Olkiluoto contained dissolved oxygen at approximately 10% or less of saturation. The presence of aerobic and anaerobic microorganisms, including methane-oxidizing bacteria, has been documented. The data confirm earlier suggested processes of oxygen reduction in the shallow part of the bedrock. These microbial processes reduce intruding oxygen in the shallow groundwater using dissolved organic carbon and methane as the main electron donors. Microbiological and geochemical data strongly suggest that the anaerobic microbial oxidation of methane (ANME) is active at a depth down to approximately 300 m in Olkiluoto, as has been suggested previously, based on interpretations of geochemical data. However, proof of the presence and activity of ANME microorganisms is needed before the existence of active ANME processes in Olkiluoto

  12. Stress evolution and fault stability at Olkiluoto during the Weichselian glaciation

    International Nuclear Information System (INIS)

    Lund, B.; Schmidt, P.

    2011-06-01

    In this study we investigate how a model of the Weichselian glacial cycle affects the state of stress in the Earth, and how those changes in stress influence the stability of faults. The main objectives for this study are the evolution of the glacially induced stresses at repository depth in Olkiluoto, Finland, and the stability field at seismogenic depths below the proposed repository. The analysis presented here is similar to the study by Lund et al. (2009) for the proposed Swedish nuclear waste repository sites of Forsmark and Oskarshamn. Along the lines of Lund et al. (2009), this study is a modeling study, where we use three-dimensional ice and earth models to calculate the glacial isostatic adjustment (GIA), i.e. the response of the Earth to an ice load, examining both displacements and stresses

  13. Nuclear power plant Olkiluoto 3. Containment leakage test under extreme conditions

    Energy Technology Data Exchange (ETDEWEB)

    Fleckenstein, Tobias [TUEV SUED Industrie Service GmbH, Munich (Germany). Measaruement Technology Dept.

    2015-01-15

    Modern nuclear power plants place high demands on the design and execution of safety checks. TUEV SUED supported the containment leakage test for the largest- capacity third generation nuclear power plant in the world - Olkiluoto 3 in Finland. The experts successfully met the challenges presented by exceptional parameters of the project. The containment of Olkiluoto 3 is unique in that the vessel's volume is 80,000 m{sup 3} while measurements were carried out over a period of ten days. To execute the test, 75 temperature and 15 humidity sensors had to be installed and correctly interlinked by more than ten kilometres of cable. These instruments also needed to withstand an absolute pressure of 6 bar, ambient temperatures of 30 C and high levels of humidity. These conditions required comprehensive preparation and a high amount of qualification tests. Parts of the qualifications were carried out at the autoclave system of the Technical University in Munich, Germany, where the project test conditions could be simulated. The software required to determine the tests was developed by TUEV SUED and verified by German's national accreditation body DAkkS under ISO 17025. TUEV SUED enabled the test schedule to continue without delay by analysing all recorded data continuously on site, including pressure, temperature, humidity and leakage mass flow curves. With the comprehensive preparation, data acquisition system recording measurements continuously and the on-time result calculation, all components of the leak-tightness assessment were successfully completed in accordance with requirements.

  14. A hydrostratigraphical approach to support environmentally safe siting of a mining waste facility at Rautuvaara, Finland

    DEFF Research Database (Denmark)

    Howett, Peter J.; Salonen, Veli-Pekka; Hyttinen, Outi

    2015-01-01

    A hydrostratigraphical approach to support environmentally safe siting of a mining waste facility at Rautuvaara, Finland Based on the construction of a detailed sedimentological model, hydrostratigraphy and local groundwater/surface water flows, this paper analyses the Niesajoki river valley...... of the valley. The thickness and complexity of sediments varied across the study area. To the E/SE of the valley, sediments are thick (~40 m), and more complex., In contrast the S/W/NW of the area, sediments are thinner (~10 m) and more simple. Groundwater is found to flow towards the centre of the valley...... and along its axis, where a bedrock controlled divide forms two groundwater basins. Based on the results of this research, it is suggested that any future expansion of the tailings facility should be restricted to the western and southern side of the valley, where waters are more manageable....

  15. Regulatory Experiences from Effective Step-wise Implementation of the SNF Disposal in Finland

    International Nuclear Information System (INIS)

    Hämäläinen, K.

    2016-01-01

    Finland is one of the foremost countries in the world in developing a disposal solution for spent nuclear fuel (SNF). The Construction License Application (CLA) for the Olkiluoto SNF encapsulation and disposal facility was submitted by Posiva, the implementer, to the authorities at the end of 2012 and the Government is expected to decide about the license during autumn 2015. In 1983 the Government made a strategy decision on the objectives and target time schedule for the research, development and technical planning of nuclear waste management. Decision included the milestones for site selection, submittal of construction license and start of disposal operations.

  16. Modelling of water-rock interaction at TVO investigation sites

    International Nuclear Information System (INIS)

    Pitkaenen, P.; Leino-Forsman, H.

    1992-12-01

    The geochemistry of the groundwater at the Kivetty, Syyry and Olkiluoto site investigation areas in Finland for nuclear waste disposal is evaluated. The hydrogeological data is collected from boreholes drilled down to 100-m depth into crystalline bedrock. The interpretation is based on groundwater chemistry and isotope data, mineralogical data, and the structure and hydrology of the bedrock, using correlation diagrams and the thermodynamic calculations (PHREEQE,EQ3NR). The hydrogeochemistry and major processes controlling the groundwater chemistry are discussed

  17. The Olkiluoto 3 project

    International Nuclear Information System (INIS)

    Knoche, Ph.

    2009-01-01

    This series of slides presents the Olkiluoto 3 project involving the EPR (European Pressurized water Reactor). This EPR is the first reactor of third generation to have be put into construction. The contract was signed between the Areva-Siemens consortium and the Tvo Finn company in december 2003. The construction of the first-off reactor is always a big challenge but also opens the way for its industrial development as it brings knowledge and experience: Olkiluoto is the first international licensing of the EPR, a valuable feedback experience has been acquired on both the fabrication of the primary components and the qualification of the suppliers. A point on the state of the construction works is made at the first term 2009. (A.C.)

  18. Statistical Analysis and Modelling of Olkiluoto Structures

    International Nuclear Information System (INIS)

    Hellae, P.; Vaittinen, T.; Saksa, P.; Nummela, J.

    2004-11-01

    Posiva Oy is carrying out investigations for the disposal of the spent nuclear fuel at the Olkiluoto site in SW Finland. The investigations have focused on the central part of the island. The layout design of the entire repository requires characterization of notably larger areas and must rely at least at the current stage on borehole information from a rather sparse network and on the geophysical soundings providing information outside and between the holes. In this work, the structural data according to the current version of the Olkiluoto bedrock model is analyzed. The bedrock model relies much on the borehole data although results of the seismic surveys and, for example, pumping tests are used in determining the orientation and continuation of the structures. Especially in the analysis, questions related to the frequency of structures and size of the structures are discussed. The structures observed in the boreholes are mainly dipping gently to the southeast. About 9 % of the sample length belongs to structures. The proportion is higher in the upper parts of the rock. The number of fracture and crushed zones seems not to depend greatly on the depth, whereas the hydraulic features concentrate on the depth range above -100 m. Below level -300 m, the hydraulic conductivity occurs in connection of fractured zones. Especially the hydraulic features, but also fracture and crushed zones often occur in groups. The frequency of the structure (area of structures per total volume) is estimated to be of the order of 1/100m. The size of the local structures was estimated by calculating the intersection of the zone to the nearest borehole where the zone has not been detected. Stochastic models using the Fracman software by Golder Associates were generated based on the bedrock model data complemented with the magnetic ground survey data. The seismic surveys (from boreholes KR5, KR13, KR14, and KR19) were used as alternative input data. The generated models were tested by

  19. Olkiluoto 3 Experience

    International Nuclear Information System (INIS)

    Tiippana, Petteri

    2011-01-01

    This paper discusses the experience from the Olkiluoto 3 nuclear power plant project from regulator's point of view. There are certain factors that have affected greatly the project progress. First, Olkiluoto 3 nuclear power plant is the first European Pressurised Reactor (EPR) being constructed. Secondly, construction of the unit started after a fairly long break in nuclear power plant construction in Europe, which had resulted in loss of experienced and qualified engineering and manufacturing resources. These factors have to be kept in mind when evaluating the experience from Olkiluoto 3. Experience discussed in this paper have to do with the licensing and regulatory oversight process, completion of the design prior to construction, experience and know-how of the participating organisations, quality management in a nuclear construction project, advanced manufacturing and construction technologies, turnkey contract with regard to licensee's responsibility, safety culture aspects in a nuclear construction project, and the role and importance of regulator's oversight. (author)

  20. The occupational safety on the construction sites of the farm production buildings in Finland

    Directory of Open Access Journals (Sweden)

    M. Hellstedt

    2013-09-01

    Full Text Available The size of farms has increased considerably during Finland's EU membership. The growth has meant big investments in the new production buildings. The buildings have been switched to big industrialhall- like constructions from small-scale ones which have contained own timber and own work contribution. The objective of the project financed by Farmers' Social Insurance Institution was to improve occupational safety on farm building construction and renovation sites by disseminating current safety practices and by developing ways of action which are better than the prevailing ones. The project consisted of a literature review, statistical analysis, as well as a farmer and designer interviews. In the statistical analysis the MATA occupational injuries insurance claims database on farmers’ claims during construction and renovation work for the years 2005 - 2008 was compared with the register of Federation of Accident Insurance Institutions on the construction workers' injuries. In comparing the reasons of the accidents a clear difference was found; poor scaffoldings and ladders are still the main culprits on farm accidents. Farmer interviews were used to assess occupational safety measures on the construction site, occurred injuries and their types, nearmiss situations and the underlying factors which have led to the injuries. Also construction safety deficiencies as well as the direct and indirect costs caused for instance because of the delay in completion of construction project were discussed. Designer interviews aimed to find out how occupational safety and health considerations are taken into account in farm building planning and counseling, and how this experience of the designers should be utilized in order to improve safety at the construction sites on farms. Farmers knew their obligations on occupational safety poorly. The situation was further worsened by the fact that on the site the supervisor tasks were only nominally executed. The

  1. Electromagnetic Sampo monitoring soundings at Olkiluoto 2010

    International Nuclear Information System (INIS)

    Korhonen, K.; Korpisalo, A.; Ojamo, H.

    2010-12-01

    The Geological Survey of Finland has carried out electromagnetic frequency-domain depth soundings at fixed measurement stations in Olkiluoto annually since 2004. The purpose of the soundings is to monitor the groundwater conditions in the vicinity of the ONKALO rock characterization facility which will ultimately be part of the final nuclear waste disposal facility for the Finnish nuclear power companies. A new monitoring survey was carried out at the turn of May-June 2010. The survey resulted in 38 successfully performed soundings at 10 stations. The data set spanning the time period of 2004 to 2010 was interpreted with layered-earth models. Most of the interpretations indicate no systematic changes in the level of deep saline groundwater. However, at one station there are indications of a systematic rise in the groundwater level. (orig.)

  2. WWER nuclear waste management regulatory experience in Finland

    International Nuclear Information System (INIS)

    Varjoranta, Tero

    2000-01-01

    About 30% of all electricity produced in Finland is generated by nuclear power. Four reactors, with a total capacity of 2 656 MW e (net), are currently in operation. At Loviisa, there are two 488 MW e WWER units (recently upgraded 440-units) and at Olkiluoto two 840 MW e BWR units. At the Loviisa plant conditioning, storage and final disposal of low-and intermediate-level wastes from reactor operation will take place at the NPP sites. Intermediate level ion exchange resins and evaporation concentrates are currently stored in tanks. However, a license application for constructing a solidification plant based on cementation is currently under STUKs regulatory review. The construction of the final repository for I/LLW at the Loviisa site was started in 1993 and the Government granted the operating license in 1998. The nuclear legislation requires disposal of spent fuel into the Finnish bedrock. (Authors)

  3. Gefinex 400S (SAMPO) EM-soundings at Olkiluoto 2009

    International Nuclear Information System (INIS)

    Jokinen, T.; Lehtimaeki, J.; Korhonen, K.

    2009-09-01

    In the beginning of June 2009 Geological Survey of Finland (GTK) carried out electromagnetic (EM) frequency soundings with Gefinex 400S equipment (Sampo) in the vicinity of ONKALO at the Olkiluoto site investigation area. The EM-monitoring sounding program started in 2004 and has been repeated since yearly in the same season. The aim of the study is to monitor the variations of the groundwater properties down to 500 m depth by the changes of the electric conductivity of the earth at ONKALO and repository area. The original measurement grid was based on two 1400 m long broadside profiles, which have 200 m mutual distance and 200 m station separation. The receiver and transmitter sites are marked with stakes and the profiles were measured using 200, 500, and 800 m coil separations. The measurement program was revised in 2007 and then again in 2009. Now 15 noisy soundings were removed from the program and 3 new points were selected from the area to the east from ONKALO. The new receiver/transmitter sites, called ABC-points were marked with stakes and the points were measured using transmitter-receiver separations 200, 400 and 800 meters. In 2009 the new EM-Sampo monitoring program included 28+9 soundings. The numerous power lines and cables in the area generate local disturbances on the sounding curves, but the SN (signal to noise) ratio and the repeatability of the results is reasonably good even with long coil separations. However, most suitable for monitoring purposes are the sites without strong shallow 3D effects. Comparison of the new results to old 2004-2008 surveys shows differences on some ARD (apparent resistivity-depth) curves. Those are mainly results of the modified shallow structures. The changes in groundwater conditions based on the monitoring results seem insignificant. (orig.)

  4. Finland: construction of the first geological storage of the world

    International Nuclear Information System (INIS)

    Garcia Neri, E.

    2015-01-01

    Finland has become the first country in the world granting a construction license for a store deep geological (AGP) for radioactive waste, as reported last November 12 Posiva, the agency management of these materials in the Baltic country. After more than 40 years of research, Posiva begin construction of this facility in Olkiluoto, which will house so end spent fuel generated in power stations Olkiluoto and Loviisa and could start operating in 2023. As noted Janne Mokka, president of Posiva, this pioneering project is not only important for Finland, but for everyone because it is the first AGP enters under construction in the world. (Author)

  5. New particle formation in air mass transported between two measurement sites in Northern Finland

    Directory of Open Access Journals (Sweden)

    M. Komppula

    2006-01-01

    Full Text Available This study covers four years of aerosol number size distribution data from Pallas and Värriö sites 250 km apart from each other in Northern Finland and compares new particle formation events between these sites. In air masses of eastern origin almost all events were observed to start earlier at the eastern station Värriö, whereas in air masses of western origin most of the events were observed to start earlier at the western station Pallas. This demonstrates that particle formation in a certain air mass type depends not only on the diurnal variation of the parameters causing the phenomenon (such as photochemistry but also on some properties carried by the air mass itself. The correlation in growth rates between the two sites was relatively good, which suggests that the amount of condensable vapour causing the growth must have been at about the same level in both sites. The condensation sink was frequently much higher at the downwind station. It seems that secondary particle formation related to biogenic sources dominate in many cases over the particle sinks during the air mass transport between the sites. Two cases of transport from Pallas to Värriö were further analysed with an aerosol dynamics model. The model was able to reproduce the observed nucleation events 250 km down-wind at Värriö but revealed some differences between the two cases. The simulated nucleation rates were in both cases similar but the organic concentration profiles that best reproduced the observations were different in the two cases indicating that divergent formation reactions may dominate under different conditions. The simulations also suggested that organic compounds were the main contributor to new particle growth, which offers a tentative hypothesis to the distinct features of new particles at the two sites: Air masses arriving from the Atlantic Ocean typically spent approximately only ten hours over land before arriving at Pallas, and thus the time for the

  6. Impact of corrosion-derived iron on the bentonite buffer within the KBS-3H disposal concept. The Olkiluoto site as case study

    International Nuclear Information System (INIS)

    Wersin, P.; Birgersson, M.; Olsson, S.; Karnland, O.; Snellman, M.

    2007-12-01

    affected by montmorillonite transformation or cementation processes. A preliminary study carried out by Carlson et al. (2006) yielded ambiguous results. The data suggested that an increase in hydraulic conductivity but no effect on swelling properties had occurred, which might be due to some cementation process. It is important to note that, at least to our knowledge, natural analogue examples displaying typical cementation features under anoxic conditions are lacking. This is contrary to examples from oxic conditions where iron oxides frequently form cementation products. The extent of iron-bentonite interaction in a KBS-3H repository was assessed by means of (1) a mass balance estimate and (2) reactive transport modelling. The mass balance results indicated that a maximum of 10 - 30 % of the montmorillonite in the buffer could be converted to a non-swelling Fe(II)-rich clay if all the iron from the supercontainer steel shell reacted with the clay. In the reactive transport model, site-specific geochemical data from Olkiluoto, corrosion data, Fe(II) sorption data and thermodynamic and kinetic clay data were included in a 1D diffusion model. A number of limiting test cases was run to explore the sensitivity of the results towards uncertainties in data and model assumptions. The general conclusion from the preliminary modelling study is that the extent of the zone transformed to non-swelling material is likely to remain spatially limited (a few centimetres) for very long times. Given the proximity of the physically affected area around the supercontainer steel shell to the tunnel boundary, however the potential impacts of an altered zone consisting of corrosion products and transformed clay material need to be considered in performance assessment calculations. In order to decrease the uncertainty of the effect of the supercontainer steel shell on the buffer's stability, careful experimental studies on Fe-bentonite interaction under anoxic conditions and including

  7. Impact of corrosion-derived iron on the bentonite buffer within the KBS-3H disposal concept. The Olkiluoto site as case study

    Energy Technology Data Exchange (ETDEWEB)

    Wersin, P. (Gruner AG, Basel (Switzerland)); Birgersson, M.; Olsson, S.; Karnland, O. (Clay Technology, Lund (Sweden)); Snellman, M. (Saanio and Riekkola Oy, Helsinki (Finland))

    2007-12-15

    in principle be affected by montmorillonite transformation or cementation processes. A preliminary study carried out by Carlson et al. (2006) yielded ambiguous results. The data suggested that an increase in hydraulic conductivity but no effect on swelling properties had occurred, which might be due to some cementation process. It is important to note that, at least to our knowledge, natural analogue examples displaying typical cementation features under anoxic conditions are lacking. This is contrary to examples from oxic conditions where iron oxides frequently form cementation products. The extent of iron-bentonite interaction in a KBS-3H repository was assessed by means of (1) a mass balance estimate and (2) reactive transport modelling. The mass balance results indicated that a maximum of 10 - 30 % of the montmorillonite in the buffer could be converted to a non-swelling Fe(II)-rich clay if all the iron from the supercontainer steel shell reacted with the clay. In the reactive transport model, site-specific geochemical data from Olkiluoto, corrosion data, Fe(II) sorption data and thermodynamic and kinetic clay data were included in a 1D diffusion model. A number of limiting test cases was run to explore the sensitivity of the results towards uncertainties in data and model assumptions. The general conclusion from the preliminary modelling study is that the extent of the zone transformed to non-swelling material is likely to remain spatially limited (a few centimetres) for very long times. Given the proximity of the physically affected area around the supercontainer steel shell to the tunnel boundary, however the potential impacts of an altered zone consisting of corrosion products and transformed clay material need to be considered in performance assessment calculations. In order to decrease the uncertainty of the effect of the supercontainer steel shell on the buffer's stability, careful experimental studies on Fe-bentonite interaction under anoxic

  8. Impact of corrosion-derived iron on the bentonite buffer within the KBS-3H disposal concept. The Olkiluoto site as case study

    International Nuclear Information System (INIS)

    Wersin, Paul; Birgersson, Martin; Olsson, Siv; Karnland, Ola; Snellman, Margit

    2008-05-01

    transformation or cementation processes. A preliminary study yielded ambiguous results. The data suggested that an increase in hydraulic conductivity but no effect on swelling properties had occurred, which might be due to some cementation process. It is important to note that, at least to our knowledge, natural analogue examples displaying typical cementation features under anoxic conditions are lacking. This is contrary to examples from oxic conditions where iron oxides frequently form cementation products. The extent of iron-bentonite interaction in a KBS-3H repository was assessed by means of (1) a mass balance estimate and (2) reactive transport modelling. The mass balance results indicated that a maximum of 10-30% of the montmorillonite in the buffer could be converted to a non-swelling Fe(II)-rich clay if all the iron from the supercontainer steel shell reacted with the clay. In the reactive transport model, site-specific geochemical data from Olkiluoto, corrosion data, Fe(II) sorption data and thermodynamic and kinetic clay data were included in a 1D diffusion model. A number of limiting test cases was run to explore the sensitivity of the results towards uncertainties in data and model assumptions. The general conclusion from the preliminary modelling study is that the extent of the zone transformed to non-swelling material is likely to remain spatially limited (a few centimetres) for very long times. Given the proximity of the physically affected area around the supercontainer steel shell to the tunnel boundary, however the potential impacts of an altered zone consisting of corrosion products and transformed clay material need to be considered in performance assessment calculations. In order to decrease the uncertainty of the effect of the supercontainer steel shell on the buffer's stability, careful experimental studies on Fe-bentonite interaction under anoxic conditions and including measurements of physical properties should be carried out. The studies should also

  9. Impact of corrosion-derived iron on the bentonite buffer within the KBS-3H disposal concept. The Olkiluoto site as case study

    Energy Technology Data Exchange (ETDEWEB)

    Wersin, Paul (National Cooperative for the Disposal of Radioactive Waste, Nagra, Wettingen (Switzerland)); Birgersson, Martin; Olsson, Siv; Karnland, Ola (Clay Technology AB, Lund (Sweden)); Snellman, Margit (Saanio and Riekkola Oy, Helsinki (Finland))

    2008-05-15

    montmorillonite transformation or cementation processes. A preliminary study yielded ambiguous results. The data suggested that an increase in hydraulic conductivity but no effect on swelling properties had occurred, which might be due to some cementation process. It is important to note that, at least to our knowledge, natural analogue examples displaying typical cementation features under anoxic conditions are lacking. This is contrary to examples from oxic conditions where iron oxides frequently form cementation products. The extent of iron-bentonite interaction in a KBS-3H repository was assessed by means of (1) a mass balance estimate and (2) reactive transport modelling. The mass balance results indicated that a maximum of 10-30% of the montmorillonite in the buffer could be converted to a non-swelling Fe(II)-rich clay if all the iron from the supercontainer steel shell reacted with the clay. In the reactive transport model, site-specific geochemical data from Olkiluoto, corrosion data, Fe(II) sorption data and thermodynamic and kinetic clay data were included in a 1D diffusion model. A number of limiting test cases was run to explore the sensitivity of the results towards uncertainties in data and model assumptions. The general conclusion from the preliminary modelling study is that the extent of the zone transformed to non-swelling material is likely to remain spatially limited (a few centimetres) for very long times. Given the proximity of the physically affected area around the supercontainer steel shell to the tunnel boundary, however the potential impacts of an altered zone consisting of corrosion products and transformed clay material need to be considered in performance assessment calculations. In order to decrease the uncertainty of the effect of the supercontainer steel shell on the buffer's stability, careful experimental studies on Fe-bentonite interaction under anoxic conditions and including measurements of physical properties should be carried out. The

  10. Cross-Borehole research with EMRE-system. Radiofrequency measurements in drillhole section OL-KR40 - OL-KR45 at Olkiluoto, 2009

    International Nuclear Information System (INIS)

    Korpisalo, A.; Niemelae, M.

    2010-04-01

    Posiva Oy carries out research and development work for the spent nuclear fuel disposal in Finland. The repository will be constructed deep in the crystalline bedrock at Olkiluoto island in Eurajoki. Construction of the underground characterization facility ONKALO started in 2004. Posiva Oy has been actively reviewing the methods for examining granitic i.e. crystalline bedrock properties. One of the considered methods was electromagnetic cross-borehole survey. This report describes the field work carried out in 2009 and the interpretation of the continuous wave device in one drillhole panel at 100-750 m depth level. Panel was conic in shape thus the collars were in close vicinity (about 10 m) at the earth surface and diverged in deeper parts being several hundreds of meters from each others. The works were carried out by Geological Survey of Finland. After the pioneering work in 2005 the device was repaired thoroughly and the proper functioning of the device was ensured after several tests. Geological-geophysical characterization of Olkiluoto site has been run since 1989, and more than 40 drillholes have been prepared

  11. Geological site selection studies for the final disposal of spent nuclear fuel in Finland

    International Nuclear Information System (INIS)

    Salmi, M.; Vuorela, P.; Kuivamaeki, A.

    1985-10-01

    In the work of selecting at the areas, heed has been taken of international geological recommendations, which have been adapted to local conditions prevailing in this country. At the present stage, the studies are largely based on the available information about the bedrock of Finland, as contained in, for example, geological maps, various geophysical maps covering the country as a whole and the maps of ore deposits and indications as well as of groundwater areas. The regional investigations of the structure of the Finnish bedrock has taken as its point of departure the study of satellite photos. These pictures best show the mosaiclike block structure of the Finnish bedrock, where the fracture zones surrounding the blocks are involved in the movements of the bedrock resulting mainly from land uplift. From the interpretation of satellite photos, attention has switched over to the interpretation of large-scale maps and stereoscopic aerial photographs. The investigation areas selected by the interpretation of aerial photos have also been studied tentatively on the ground to obtain a more accurate comparative estimation of the different localities. Of the areas chosen for study, the majority consist of granites, which best meet the geological site selection recommendations. The investigation areas have been classified into four categories according to how well they are suited to further study. One important criterion in the classification has been the amount of information obtainable from the bedrock. The areas included in the first category have well exposed and solid bedrock. The areas chosen for inclusion in the second category contain fewer outcrops and are not so easy to study with respect to the structure of the bedrock. The areas included in the third category are generally blanketed under surficial deposits with the result that obtaining reliable information about the bedrock calls for further investigation. The fourth category represents areas where features

  12. Results of monitoring at Olkiluoto in 2009. Environment

    International Nuclear Information System (INIS)

    Haapanen, A.

    2010-10-01

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2009. These summary reports have been published since 2005. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground characterization facility. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). Monitoring has been carried out for varying periods of time depending on the sector: some monitoring activities performed by TVO originate from the 1970s and the repository-related environmental monitoring of Olkiluoto from the early 2000s. The monitoring programme evolves according to the experiences gained from the modelling work and an increased understanding of the site. Augmentations in 2009 include e.g. establishment of a new forest intensive monitoring plot (FIP14), continuation of studies on fine roots and on the species composition and abundances of small mammals. Line transect samplings of ants, terrestrial snails and earthworms were carried out and a systematic monitoring of island birds was started. In addition, a project was started where the sediment load and factors affecting the sediment transportation into Eurajoensalmi bay is examined. Dust produced during construction of the third nuclear power unit (OL3), ONKALO and related infrastructure can be seen in the soil solution and deposition results. Furthermore, the construction works and road traffic have a raising effect on the noise levels of the immediate surroundings. The land-use continues to change, but the remaining natural environment resembles other coastal locations. The young age of the soils and the closeness of the sea are reflected in the soil properties. Mammalian fauna on the island is typical of coastal

  13. Results of monitoring at Olkiluoto in 2009. Environment

    Energy Technology Data Exchange (ETDEWEB)

    Haapanen, A. (ed.) (Haapanen Forest Consulting, Vanhakylae (Finland))

    2010-10-15

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2009. These summary reports have been published since 2005. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground characterization facility. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). Monitoring has been carried out for varying periods of time depending on the sector: some monitoring activities performed by TVO originate from the 1970s and the repository-related environmental monitoring of Olkiluoto from the early 2000s. The monitoring programme evolves according to the experiences gained from the modelling work and an increased understanding of the site. Augmentations in 2009 include e.g. establishment of a new forest intensive monitoring plot (FIP14), continuation of studies on fine roots and on the species composition and abundances of small mammals. Line transect samplings of ants, terrestrial snails and earthworms were carried out and a systematic monitoring of island birds was started. In addition, a project was started where the sediment load and factors affecting the sediment transportation into Eurajoensalmi bay is examined. Dust produced during construction of the third nuclear power unit (OL3), ONKALO and related infrastructure can be seen in the soil solution and deposition results. Furthermore, the construction works and road traffic have a raising effect on the noise levels of the immediate surroundings. The land-use continues to change, but the remaining natural environment resembles other coastal locations. The young age of the soils and the closeness of the sea are reflected in the soil properties. Mammalian fauna on the island is typical of coastal

  14. Decision nearing on final disposal of spent fuel in Finland

    International Nuclear Information System (INIS)

    Vira, J.

    2000-01-01

    The programme for final disposal of spent fuel from Finnish nuclear power plants is entering into important phase: in the year 2000 the Finnish Government is expected to decide whether the proposal made by Posiva Oy on the spent fuel disposal is in line with the overall good of society. Associated with the decision is also Posiva's proposal on siting the disposal facility at Olkiluoto in Eurajoki municipality on the western coast of Finland. An important document underlying Posiva's application for this principle decision is the report of the environmental impact assessment, which was completed in 1999. Safety considerations play an important role in the application. New assessments have, therefore, been made on both the operational and long-term safety as well as on safety of spent fuel transportation. (author)

  15. The Finnish final disposal programme proceeds to the site selection

    International Nuclear Information System (INIS)

    Seppaelae, T.

    1999-01-01

    Research for the selection of the final disposal site has been carried out already since the beginning of 1980's. Field studies were started in 1987: In the recent years, studied sites have included Olkiluoto in Eurajoki, Haestholmen in Loviisa, Romuvaara in Kuhmo and Kivetty in Aeaenekoski. Based on 40 years operation of four power plant units, the estimate for the accumulation of spent fuel to be disposed of in Finland is 2,600 tU. A 'Decision in Principle' is needed from the Finnish government to select the final disposal site, Posiva submitted the application for a policy decision in May 1999. The intended site of the facility is Olkiluoto which produces most of the spent fuel in Finland: A disposal would minimise the need of transports. In a poll among the inhabitants of Eurajoki, 60 per cent approved the final disposal facility. After a positive decision of the government, Posiva will construct an underground research facility in Olkiluoto. The construction of the final disposal facility will take place in the 2010's, the facility should be operational in 2020. (orig.) [de

  16. Assessment of potential perturbations to Posiva's SF repository at Olkiluoto from the ONKALO Facility

    International Nuclear Information System (INIS)

    Alexander, W.R.; Neall, F.B.

    2007-06-01

    Although the site of the proposed spent fuel repository at Olkiluoto in southwest Finland has been extensively investigated over the last fifteen years, Posiva decided to construct a rock characterisation facility (RCF) at the site to collect more detailed information on the host rock. The data provided by the ONKALO RCF will support the detailed repository design and safety assessment (SA) and will allow construction and disposal methods to be tested under relevant in situ conditions. ONKALO has been so designed that it can act as access routes and auxiliary rooms for the SF repository and so may be in use for the entire operational phase of the repository (currently up to 100 years). Extensive experience from deep mining suggests that such an extended period of operation could have a major impact on both the host rock formation and any nearby facilities, such as the SF repository, and, consequently, Posiva decided to investigate potential perturbations to the repository caused by the existence of ONKALO. A preliminary assessment was carried out in 2003, before construction of the RCF began, and this was recently partially updated in early 2006. This current report represents the most recent update of these reports and has the primary aims of: checking if the previous reports have missed any essential issues; evaluating whether the identified issues have been treated in an appropriate manner; updating the reports in the light of new information. This is carried out based on data from ONKALO itself and on improved understanding of some of the perturbation mechanisms identified in the original studies along with a consideration of newly identified processes. This report differs from the previous studies in addressing the issues in a more SA-oriented manner (for example, focussing the examination of potential perturbations on a re-worked FEP list), allowing the work reported here to be more easily dovetailed with future SA studies on the Olkiluoto repository

  17. Fuel reliability experience in Finland

    International Nuclear Information System (INIS)

    Kekkonen, L.

    2015-01-01

    Four nuclear reactors have operated in Finland now for 35-38 years. The two VVER-440 units at Loviisa Nuclear Power Plant are operated by Fortum and two BWR’s in Olkiluoto are operated by Teollisuuden Voima Oyj (TVO). The fuel reliability experience of the four reactors operating currently in Finland has been very good and the fuel failure rates have been very low. Systematic inspection of spent fuel assemblies, and especially all failed assemblies, is a good practice that is employed in Finland in order to improve fuel reliability and operational safety. Investigation of the root cause of fuel failures is important in developing ways to prevent similar failures in the future. The operational and fuel reliability experience at the Loviisa Nuclear Power Plant has been reported also earlier in the international seminars on WWER Fuel Performance, Modelling and Experimental Support. In this paper the information on fuel reliability experience at Loviisa NPP is updated and also a short summary of the fuel reliability experience at Olkiluoto NPP is given. Keywords: VVER-440, fuel reliability, operational experience, poolside inspections, fuel failure identification. (author)

  18. Aerogeophysical survey in Olkiluoto 2009

    International Nuclear Information System (INIS)

    Kurimo, M.

    2009-08-01

    This report describes the survey operation, survey and processing methods and the deliverables of an aerogeophysical survey in Olkiluoto area in May 2009. The survey was conducted by Geological Survey of Finland (GTK). The survey aircraft was a twin-engine Twin Otter operated by Finnish Aviation Academy (SIO) and owned by Natural Environment Research Council / British Geological Survey (NERC / BGS), with whom GTK has established a joint venture called Joint Airborne-geoscience Capability (JAC). The survey was conducted in May 2009 between May 5th and May 18th. The survey consists of ten separate survey flights and two magnetic calibration flights. The survey was based in Pori airport. Survey line spacing was 50 meters and nominal survey altitude was 30 meters. Measurements were completed in May 2009, and data processing and reporting was done in June 2009. Two cesium magnetometers installed onboard the aircraft (at the left wingtip and in a nose cone) were measuring the magnetic total field intensity during the survey flights. An automatic compensation unit corrected the aircraft attitude errors in the magnetic data in real time. The four-frequency electromagnetic (EM) unit included four transmitter coils with amplifiers in right wingtip and four receiver coils in left wingtip. Frequencies were 900 Hz, 3 kHz, 14 kHz and 24.5 kHz. The gamma spectrometer with two crystal packages (total volume 42 litres) measured the 256 channel energy spectra. In addition, auxiliary parameters such as flight altitude and aircraft attitude were also recorded simultaneously. Reference ground base station was used for recording the temporal variations in the magnetic field and also reference data for post-positioning of coordinate information. In the post-processing phase, heading correction, base station correction and microlevelling procedures were applied to the magnetic data. The EM data and radiometric data were corrected with calibration coefficients and levelled. The data was

  19. Flow measurements and hydraulic interference tests at the Olkiluoto site in Eurajoki, drillholes OL-KR14, OL-KR30, OL-PP66, OL-PP67, OL-PP68 and OL-PP69

    Energy Technology Data Exchange (ETDEWEB)

    Komulainen, J. [Poeyry Finland Oy, Vantaa (Finland)

    2014-08-15

    The measurements described in this report are part of the infiltration experiment carried out at Olkiluoto. The emphasis of these measurements is on obtaining more detailed data on hydraulically significant fractures in the infiltration experiment area. The selected fractures or sections were pumped in turn and flow responses were observed in the other holes by the PFL DIFF-tool. The flow measurements were carried out in drillholes OL-KR14, OL-KR30, OL-PP66, OL-PP67, OL-PP68 and OL-PP69 on the Olkiluoto investigation site between January 2013 and July 2013. Two different flowmeters were used for the measurements. Posiva Flow Log, Difference flow method (PFL DIFF) was used for the determination of hydraulic conductivity and hydraulic head in fractures/fractured zones in the drillholes. PFL DIFF flow logging was conducted in all the drillholes mentioned above. Posiva Flow Log, Transverse flow method (PFL TRANS) was used to determine groundwater flow direction and flow rate across a drillhole. The transverse flow method was used in drillholes OL-KR14 and OL-PP69. PFL DIFF and PFL TRANS measurements had been carried out earlier in drillholes OL-PP66, OL-PP67, OL-PP68 and OL-PP69. The most recent measurements were conducted in 2011. Those measurements were carried out when drillhole OL-KR14 was pumped at packed-off section 13 m - 18 m. Both PFL DIFF and PFL TRANS flowmeters include an electrode for measuring single point resistance (SPR). The device has a high depth resolution and the results were used for depth synchronisation between consecutive DIFF and TRANS measurements. (orig.)

  20. Olkiluoto hydrogeochemistry. A 3-D modelling approach for sparce data set

    International Nuclear Information System (INIS)

    Luukkonen, A.; Partamies, S.; Pitkaenen, P.

    2003-07-01

    Olkiluoto at Eurajoki has been selected as a candidate site for final disposal repository for the used nuclear waste produced in Finland. In the long term safety assessment, one of the principal evaluation tools of safe disposal is hydrogeochemistry. For assessment purposes Posiva Oy excavates in the Olkiluoto bedrock an underground research laboratory (ONKALO). The complexity of the groundwater chemistry is characteristic to the Olkiluoto site and causes a demand to examine and visualise these hydrogeochemical features in 3-D together with the structural model. The need to study the hydrogeochemical features is not inevitable only in the stable undisturbed (pre-excavational) conditions but also in the disturbed system caused by the construction activities and open-tunnel conditions of the ONKALO. The present 3-D approach is based on integrating the independently and separately developed structural model and the results from the geochemical mixing calculations of the groundwater samples. For spatial geochemical regression purposes the study area is divided into four primary sectors on the basis of the occurrence of the samples. The geochemical information within the four primary sector are summed up in the four sector centroids that sum-up the depth distributions of the different water types within each primary sector area. The geographic locations of the centroids are used for secondary division of the study area into secondary sectors. With the aid of secondary sectors spatial regressions between the centroids can be calculated and interpolation of water type fractions within the centroid volume becomes possible. Similarly, extrapolations outside the centroid volume are possible as well. The mixing proportions of the five detected water types in an arbitrary point in the modelling volume can be estimated by applying the four centroids and by using lateral linear regression. This study utilises two separate data sets: the older data set and the newer data set. The

  1. Aquatic ecosystem characterisation strategy at a repository site

    Energy Technology Data Exchange (ETDEWEB)

    Kangasniemi, Ville; Ikonen, Ari T.K. [Environmental Research and Assessment EnviroCase, Ltd., Hallituskatu 1 D 4, 28100 Pori (Finland); Lahdenperae, Anne-Maj [Saanio and Riekkola Oy, Laulukuja 4, 00420 Helsinki (Finland); Kirkkala, Teija [Pyhaejaervi Institute, Sepaentie 7, 27500 Kauttua (Finland); Koivunen, Sari [Water and Environment Research of South-West Finland, Telekatu 16, 20360 Turku (Finland)

    2014-07-01

    Olkiluoto Island on the western coast of Finland has been selected as a repository site for spent nuclear fuel disposal. According to regulatory requirements, the safety assessment for the repository should have an assessment timeframe of several millennia. Due to the post-glacial land uplift, the relatively shallow sea areas around Olkiluoto Island will change gradually to lakes, rivers and terrestrial areas. As there are no limnic systems at present Olkiluoto site, the reference area was delineated and reference lakes and rivers were selected as an analogue. For the modelling of the transport and accumulation of possible radionuclide releases in the surface environment, aquatic ecosystems were identified and divided into biotopes. Despite the number of available templates, the division of aquatic environment for the biosphere assessment of the Olkiluoto spent fuel repository was necessary to made separately. In this contribution, the processes behind the identification of aquatic ecosystems (e.g. legislation, physical and chemical properties) together with the biotope selection methodology (e.g. light and bottom conditions) and the challenges related to the amount of variable input parameters for each biotope in the modelling are presented. (authors)

  2. Petrology of Olkiluoto

    International Nuclear Information System (INIS)

    Kaerki, A.; Paulamaeki, S.

    2006-11-01

    The rocks of Olkiluoto fall into four main groups: (1) gneisses, (2) migmatitic gneisses, (3) TGG-gneisses (TGG = tonalite-granodiorite-granite) and 4) pegmatitic granites. In addition, narrow diabase dykes occur sporadically. The gneisses include homogeneous mica-bearing quartz gneisses, banded mica gneisses and hornblende or pyroxene-bearing mafic gneisses. The migmatitic gneisses, which typically comprise 20 - 40% leucosome, can be divided into three subgroups in terms of their migmatite structures: veined gneisses, stromatic gneisses and diatexitic gneisses. The leucosomes of the veined gneisses show vein-like, more or less elongated traces with some features similar to augen structures. Planar leucosome layers characterize the stromatic gneisses, while the migmatite structure of the diatexitic gneisses is asymmetric and irregular. The TGG gneisses are medium-grained, relatively homogeneous rocks that can show a blastomylonitic foliation, but they can also resemble plutonic, unfoliated rocks. The pegmatitic granites are leucocratic, very coarse-grained rocks, which may contain large garnet, tourmaline and cordierite phenocrysts. Mica gneiss inclusions are typical of the larger pegmatitic bodies. Gneisses, which are weakly or not at all migmatitic, make ca. 9% of the bedrock. Migmatitic gneisses make up over 64% of the volume of the Olkiluoto bedrock, with the veined gneisses accounting for 43%, the stromatic gneisses for 0.4% and the diatexitic gneisses for 21%, based on drill core logging. Of the remaining lithologies, TGG gneisses constitute 8% and pegmatitic granites almost 20% by volume. The supracrustal rocks of Olkiluoto can be divided into four series by reference to whole rock chemical composition: a T series, S series, P series and basic, volcanogenic gneisses. Rocks of the T, S and P series seem to make up 42%, 12% and 26%, respectively, of the volume of central part of the island of Olkiluoto, in addition to which, pegmatitic granites and diabases

  3. Electrical model of Olkiluoto

    Energy Technology Data Exchange (ETDEWEB)

    Paananen, M.; Lehtonen, T.; Korhonen, K. (Geological Survey of Finland, Espoo (FI))

    2007-05-15

    The goal of this work is to construct a composite electrical model of Olkiluoto, focussing on integration of four separate geophysical methods: mise-a-la-masse (MAM), SAMPO EM soundings, Slingram (HLEM) and single-hole electrical soundings. The electrical structure of Olkiluoto is rather complex, dominated by mineral electrical conductors such as sulphide minerals and graphite. The basic idea of this work is the fact that the sulphide-rich zones and fracturing appear to coincide frequently. Accordingly, knowing the geometry of the major electric conductors would facilitate the interpretation of brittle deformation zones. The work consists of three separate phases: method-specific interpretation, integration and block modelling. In the single-hole interpretation, locations of electric conductors (resistivity < 1000 ohmm), based on long normal survey have been determined in 42 drillholes. Since MAM survey does not cover all the conductive sections and drillholes and SAMPO EM has its own limitations in sensitivity and resolution, a proportion of the conductive sections have been combined between the drillholes using only the single-hole data and the geological idea of features dipping gently to SE - S. The MAM survey has been done in numerous drillholes in order to find galvanic connections between the drillholes. Based on MAM, geometry of numerous electric conductors has been determined. Generally the results indicate continuous, gently dipping semiplanar features intersected by several drillholes. The Slingram survey and interpretation have been done on the ground surface to map electric conductors located at shallow depths (some tens of meters at maximum). A number of conductive zones have been delineated, trending mainly from ENE to WSW. The conductors have also been classified according to their in-phase/quadrature-ratio, and in some cases, also numerical modelling has been done. The SAMPO EM soundings and interpretations have been done to map subsurface electric

  4. Electrical model of Olkiluoto

    International Nuclear Information System (INIS)

    Paananen, M.; Lehtonen, T.; Korhonen, K.

    2007-05-01

    The goal of this work is to construct a composite electrical model of Olkiluoto, focussing on integration of four separate geophysical methods: mise-a-la-masse (MAM), SAMPO EM soundings, Slingram (HLEM) and single-hole electrical soundings. The electrical structure of Olkiluoto is rather complex, dominated by mineral electrical conductors such as sulphide minerals and graphite. The basic idea of this work is the fact that the sulphide-rich zones and fracturing appear to coincide frequently. Accordingly, knowing the geometry of the major electric conductors would facilitate the interpretation of brittle deformation zones. The work consists of three separate phases: method-specific interpretation, integration and block modelling. In the single-hole interpretation, locations of electric conductors (resistivity < 1000 ohmm), based on long normal survey have been determined in 42 drillholes. Since MAM survey does not cover all the conductive sections and drillholes and SAMPO EM has its own limitations in sensitivity and resolution, a proportion of the conductive sections have been combined between the drillholes using only the single-hole data and the geological idea of features dipping gently to SE - S. The MAM survey has been done in numerous drillholes in order to find galvanic connections between the drillholes. Based on MAM, geometry of numerous electric conductors has been determined. Generally the results indicate continuous, gently dipping semiplanar features intersected by several drillholes. The Slingram survey and interpretation have been done on the ground surface to map electric conductors located at shallow depths (some tens of meters at maximum). A number of conductive zones have been delineated, trending mainly from ENE to WSW. The conductors have also been classified according to their in-phase/quadrature-ratio, and in some cases, also numerical modelling has been done. The SAMPO EM soundings and interpretations have been done to map subsurface electric

  5. Modelling end-glacial earthquakes at Olkiluoto

    International Nuclear Information System (INIS)

    Faelth, B.; Hoekmark, H.

    2011-02-01

    The objective of this study is to obtain estimates of the possible effects that post-glacial seismic events in three verified deformation zones (BFZ100, BFZ021/099 and BFZ214) at the Olkiluoto site may have on nearby fractures in terms of induced fracture shear displacement. The study is carried out by use of large-scale models analysed dynamically with the three dimensional distinct element code 3DEC. Earthquakes are simulated in a schematic way; large planar discontinuities representing earthquake faults are surrounded by a number of smaller discontinuities which represent rock fractures in which shear displacements potentially could be induced by the effects of the slipping fault. Initial stresses, based on best estimates of the present-day in situ stresses and on state-of-the-art calculations of glacially-induced stresses, are applied. The fault rupture is then initiated at a pre-defined hypocentre and programmed to propagate outward along the fault plane with a specified rupture velocity until it is arrested at the boundary of the prescribed rupture area. Fault geometries, fracture orientations, in situ stress model and material property parameter values are based on data obtained from the Olkiluoto site investigations. Glacially-induced stresses are obtained from state-of-the-art ice-crust/mantle finite element analyses. The response of the surrounding smaller discontinuities, i.e. the induced fracture shear displacement, is the main output from the simulations

  6. Operation set for 2018 as regulator considers olkiluoto-3 licence application

    Energy Technology Data Exchange (ETDEWEB)

    Kraev, Kamen [NucNet, Brussels (Belgium)

    2017-02-15

    Finland has announced progress with its delayed nuclear project and has confirmed it will not be affected by anomalies discovered in some components manufactured for EPRs in France. The Olkiluoto-3 European Pressurised Reactor (EPR) nuclear plant under construction in Finland is on schedule to begin commercial operation in 2018 with the country's regulator preparing a safety assessment that will pave the way for fuel loading. Jouni Silvennoinen, senior vice-president for Olkiluoto-3 at Teollisuuden Voima Oyj (TVO), told NucNet that fuel loading at the EPR plant, which is nine years behind schedule, is expected in the spring of 2018. He said construction and licensing of the plant are progressing.

  7. GPS deformation measurements at Olkiluoto in 2013

    International Nuclear Information System (INIS)

    Nyberg, S.; Kallio, U.; Koivula, H.

    2014-08-01

    The Finnish Geodetic Institute has monitored crustal deformations since mid-1990s at Olkiluoto, Kivetty and Romuvaara. The research was focused on the Olkiluoto area in 2001, when Olkiluoto was chosen to the site for the final disposal facility of the spent nuclear fuel. The work and the results of the GPS deformation monitoring at Olkiluoto in 2013 are presented. The measurement consisted of two GPS measurement campaigns, observations at local permanent stations and control markers measurements at four stations. In spring six new stations were set up for permanent tracking. In total 12 permanent stations were operating continuously from April to the end of the year. The residual time series of the stations showed periodic trends up to 3 mm in height and 1 mm in horizontal component relative to the GPS1 station. A few stations were still measured as campaign-based and analysed baseline by baseline. The data from permanent stations (GPS1-GPS9, and GPS13) were included. The analysis of the inner network based on campaign sessions showed very small motions as in previous years: 75 % of change rates are smaller than 0.10 mm/y. Roughly one third of the change rates could be considered statistically significant at 1 % significance level. Statistically significant change rates were estimated for baselines from GPS1 and GPS5. The trends and strains differed at some baselines clearly from the earlier analysis because of different troposphere modelling. The results of the outer network showed the largest difference on the baseline GPS1-GPS11 where the trend decreased from -0.42 mm/y to -0.28 mm/y. The strain pattern of the outer network shows an eastwards motion of GPS1. The estimated strains for the baselines east of GPS1 were -0.03/-0.04 ppm/y. The control marker measurements were carried at the stations GPS1, GPS2, GPS4 and GPS6. A comparison of the results with the previous measurements showed that the distance between control markers at GPS6 continues to increase. Also

  8. Simulations of permafrost evolution at Olkiluoto

    Energy Technology Data Exchange (ETDEWEB)

    Hartikainen, J. [Aalto Univ., Espoo (Finland)

    2013-07-15

    This report provides numerical estimations of the evolution of permafrost and perennially frozen ground at Olkiluoto on time-scales of 60,000 and 125,000 years using Olkiluoto's site-specific information on time histories of ground level temperatures, ice sheet thickness, basal conditions, shoreline migration, soil and vegetation cover as well as heat generation from the spent fuel at a depth of 420 metres. When considering environmental conditions akin to the last glacial cycle for a 125,000 years long period, the maximum permafrost depth over the repository area can exceed the depth of 300 m and the maximum depth of perennially frozen ground the depth of 270 m. If Olkiluoto, after a 50,000 years long temperate phase of boreal climate, was subjected to a 10,000 years long periglacial period with air temperature decreased between -5 deg C and -10 deg C, the maximum permafrost depth would range between 60 and 240 m and the maximum depth of perennially frozen ground between 50 and 220 m. Furthermore, permafrost would reach the repository depth in 10,000 years, if the air temperature was lowered down to -15 deg C and the ground surface had a very thin vegetation and snow cover. Alternatively, if Olkiluoto experienced a 125,000 years long glacial cycle with a very long periglacial periods of low air temperatures and thin vegetation and snow cover and without any ice sheet development, permafrost would reach the depth of 400 m in 98,000 years and perennially frozen ground in 101,000 years. The areal distribution of permafrost and perennially frozen ground are broadly affected by the snow cover, lakes and the peat areas, especially when an extensive peat growth occurs. The lack of snow cover can enhance the evolution of the maximum depth of permafrost and perennially frozen ground by over 50 %. In addition, ground thermal conditions and the heat generation from the spent fuel modify the spatial and temporal development of permafrost and perennially frozen ground. A

  9. Simulations of permafrost evolution at Olkiluoto

    International Nuclear Information System (INIS)

    Hartikainen, J.

    2013-07-01

    This report provides numerical estimations of the evolution of permafrost and perennially frozen ground at Olkiluoto on time-scales of 60,000 and 125,000 years using Olkiluoto's site-specific information on time histories of ground level temperatures, ice sheet thickness, basal conditions, shoreline migration, soil and vegetation cover as well as heat generation from the spent fuel at a depth of 420 metres. When considering environmental conditions akin to the last glacial cycle for a 125,000 years long period, the maximum permafrost depth over the repository area can exceed the depth of 300 m and the maximum depth of perennially frozen ground the depth of 270 m. If Olkiluoto, after a 50,000 years long temperate phase of boreal climate, was subjected to a 10,000 years long periglacial period with air temperature decreased between -5 deg C and -10 deg C, the maximum permafrost depth would range between 60 and 240 m and the maximum depth of perennially frozen ground between 50 and 220 m. Furthermore, permafrost would reach the repository depth in 10,000 years, if the air temperature was lowered down to -15 deg C and the ground surface had a very thin vegetation and snow cover. Alternatively, if Olkiluoto experienced a 125,000 years long glacial cycle with a very long periglacial periods of low air temperatures and thin vegetation and snow cover and without any ice sheet development, permafrost would reach the depth of 400 m in 98,000 years and perennially frozen ground in 101,000 years. The areal distribution of permafrost and perennially frozen ground are broadly affected by the snow cover, lakes and the peat areas, especially when an extensive peat growth occurs. The lack of snow cover can enhance the evolution of the maximum depth of permafrost and perennially frozen ground by over 50 %. In addition, ground thermal conditions and the heat generation from the spent fuel modify the spatial and temporal development of permafrost and perennially frozen ground. A

  10. GPS deformation measurements at Olkiluoto in 2013

    Energy Technology Data Exchange (ETDEWEB)

    Nyberg, S.; Kallio, U.; Koivula, H. [Finnish Geodetic Institute, Masala (Finland)

    2014-08-15

    The Finnish Geodetic Institute has monitored crustal deformations since mid-1990s at Olkiluoto, Kivetty and Romuvaara. The research was focused on the Olkiluoto area in 2001, when Olkiluoto was chosen to the site for the final disposal facility of the spent nuclear fuel. The work and the results of the GPS deformation monitoring at Olkiluoto in 2013 are presented. The measurement consisted of two GPS measurement campaigns, observations at local permanent stations and control markers measurements at four stations. In spring six new stations were set up for permanent tracking. In total 12 permanent stations were operating continuously from April to the end of the year. The residual time series of the stations showed periodic trends up to 3 mm in height and 1 mm in horizontal component relative to the GPS1 station. A few stations were still measured as campaign-based and analysed baseline by baseline. The data from permanent stations (GPS1-GPS9, and GPS13) were included. The analysis of the inner network based on campaign sessions showed very small motions as in previous years: 75 % of change rates are smaller than 0.10 mm/y. Roughly one third of the change rates could be considered statistically significant at 1 % significance level. Statistically significant change rates were estimated for baselines from GPS1 and GPS5. The trends and strains differed at some baselines clearly from the earlier analysis because of different troposphere modelling. The results of the outer network showed the largest difference on the baseline GPS1-GPS11 where the trend decreased from -0.42 mm/y to -0.28 mm/y. The strain pattern of the outer network shows an eastwards motion of GPS1. The estimated strains for the baselines east of GPS1 were -0.03/-0.04 ppm/y. The control marker measurements were carried at the stations GPS1, GPS2, GPS4 and GPS6. A comparison of the results with the previous measurements showed that the distance between control markers at GPS6 continues to increase. Also

  11. Evaluation of the radioactive waste characterisation at the Olkiluoto nuclear power plant

    International Nuclear Information System (INIS)

    Kekki, T.; Titta, A.

    2000-03-01

    The aim of this study is to evaluate the physical, chemical and radiological characterisation, handling and documentation of the radioactive waste packages to be disposed of in the VLJ-repository at the Olkiluoto NPP. A comparison with the current practices in Europe, based on information from Sweden, Spain and Czech Republic, is made. The report presents recommendations for STUK to harmonise the LILW waste management practises in Finland with those in Europe. (orig.)

  12. Electromagnetic Sampo soundings at Olkiluoto in 2007

    International Nuclear Information System (INIS)

    Korhonen, K.; Lehtimaeki, J.

    2007-11-01

    The Geological Survey of Finland (GTK) carried out a Sampo Gefinex 400S frequency domain electromagnetic (EM) survey in the central part of the eastern Olkiluoto island. The survey comprised a total of 408 soundings; 134 of these were measurements of EM noise. The goal of the survey was to supplement previously performed soundings. The measurements of EM noise were used to analyse the influence of power lines on the soundings. A statistically significant correlation was found between EM noise and the distance between the receiver and the high-voltage power line located northeast of the research area. The high-voltage power line exerted a considerable influence on the soundings. Numerical modelling was used to evaluate the effect of a dipping layer on the interpretation of Sampo soundings, which is based on the 1-D layered earth model. The results indicate that Sampo interpretation is robust even in the case of a dipping layer, assuming that the dip of the layer is not steep, and both the transmitter and receiver are located above the layer. The interpretations of the soundings indicate three conducting layers. There appear to be two layers of significant conductivity above the depth of 600 m. These layers may be indications of sulphide and/or graphite rich layers. Furthermore, a deeper conducting layer below the depth of 600 m was also indicated by the interpretations. This layer may indicate deep saline groundwater. (orig.)

  13. Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Summary report

    International Nuclear Information System (INIS)

    Smith, Paul; Neall, Fiona; Snellman, Margit; Pastina, Barbara; Nordman, Henrik; Johnson, Lawrence; Hjerpe, Thomas

    2008-03-01

    The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. KBS-3H and KBS-3V are the two design alternatives of the KBS-3 spent fuel disposal method. Posiva and SKB have conducted a joint research, demonstration and development (RDandD) programme in 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The overall objectives of the present phase covering the period 2004-2007 have been to demonstrate that the horizontal deposition alternative is technically feasible and to demonstrate that it fulfils the same long-term safety requirements as KBS-3V. The safety studies conducted as part of this programme include a safety assessment of a preliminary design of a KBS-3H repository for spent nuclear fuel located about 400 m underground at the Olkiluoto site, which is the proposed site for a spent fuel repository in Finland. This safety assessment is summarised in the present report. The scientific basis of the safety assessment includes around 30 years of scientific RandD and technical development in the Swedish and Finnish KBS-3V programmes. Much of this scientific basis is directly applicable to KBS-3H. This has allowed the KBS-3H safety studies to focus on those issues that are unique to this design alternative, identified in a systematic 'difference analysis' of KBS-3H and KBS-3V. This difference analysis has shown that the key differences in the evolution and performance of KBS-3H and KBS-3V relate mainly to the engineered barrier system and to the impact of local variations in the rate of groundwater inflow on buffer saturation along the KBS-3H deposition drifts. No features or processes specific to KBS-3H have been identified that could lead to a loss or substantial degradation of the safety functions of the engineered barriers over a million year time frame. Radionuclide release from the repository near field in the event of

  14. Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Summary report

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Paul; Neall, Fiona; Snellman, Margit; Pastina, Barbara; Nordman, Henrik; Johnson, Lawrence; Hjerpe, Thomas

    2008-03-15

    The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. KBS-3H and KBS-3V are the two design alternatives of the KBS-3 spent fuel disposal method. Posiva and SKB have conducted a joint research, demonstration and development (RDandD) programme in 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The overall objectives of the present phase covering the period 2004-2007 have been to demonstrate that the horizontal deposition alternative is technically feasible and to demonstrate that it fulfils the same long-term safety requirements as KBS-3V. The safety studies conducted as part of this programme include a safety assessment of a preliminary design of a KBS-3H repository for spent nuclear fuel located about 400 m underground at the Olkiluoto site, which is the proposed site for a spent fuel repository in Finland. This safety assessment is summarised in the present report. The scientific basis of the safety assessment includes around 30 years of scientific RandD and technical development in the Swedish and Finnish KBS-3V programmes. Much of this scientific basis is directly applicable to KBS-3H. This has allowed the KBS-3H safety studies to focus on those issues that are unique to this design alternative, identified in a systematic 'difference analysis' of KBS-3H and KBS-3V. This difference analysis has shown that the key differences in the evolution and performance of KBS-3H and KBS-3V relate mainly to the engineered barrier system and to the impact of local variations in the rate of groundwater inflow on buffer saturation along the KBS-3H deposition drifts. No features or processes specific to KBS-3H have been identified that could lead to a loss or substantial degradation of the safety functions of the engineered barriers over a million year time frame. Radionuclide release from the repository near field in the

  15. Safety Assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto

    International Nuclear Information System (INIS)

    Smith, P.; Neall, F.; Snellman, M.; Pastina, B.; Hjerpe, T.; Nordman, H.; Johnson, L.

    2007-12-01

    The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. KBS-3H and KBS-3V are the two design alternatives of the KBS-3 spent fuel disposal method. Posiva and SKB have conducted a joint research, demonstration and development (RD and D) programme in 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The overall objectives of the present phase covering the period 2004-2007 have been to demonstrate that the horizontal deposition alternative is technically feasible and to demonstrate that it fulfils the same long-term safety requirements as KBS-3V. The safety studies conducted as part of this programme include a safety assessment of a preliminary design of a KBS-3H repository for spent nuclear fuel located about 400 m underground at the Olkiluoto site, which is the proposed site for a spent fuel repository in Finland. This safety assessment is summarised in the present report. The scientific basis of the safety assessment includes around 30 years of scientific R and D and technical development in the Swedish and Finnish KBS-3V programmes. Much of this scientific basis is directly applicable to KBS-3H. This has allowed the KBS-3H safety studies to focus on those issues that are unique to this design alternative, identified in a systematic difference analysis of KBS-3H and KBS-3V. This difference analysis has shown that the key differences in the evolution and performance of KBS-3H and KBS-3V relate mainly to the engineered barrier system and to the impact of local variations in the rate of groundwater inflow on buffer saturation along the KBS-3H deposition drifts. No features or processes specific to KBS-3H have been identified that could lead to a loss or substantial degradation of the safety functions of the engineered barriers over a million year time frame. Radionuclide release from the repository near field in the event of

  16. Difference flow and electrical conductivity measurements at the Olkiluoto site in Eurajoki, drillholes OL-KR54, OL-KR55, OL-KR55B and OL-KR47B

    Energy Technology Data Exchange (ETDEWEB)

    Komulainen, J.; Poellaenen, J.; Hurmerinta, E.; Ripatti, K. [Poeyry Finland Oy, Espoo (Finland)

    2012-04-15

    The Posiva Flow Log, Difference flow method (PFL DIFF) uses a flowmeter that incorporates a flow guide and can be used for relatively quick determinations of hydraulic conductivity and hydraulic head of fractures/fractured zones in drillholes. This report presents the principles of the method and the results of measurements carried out in drillholes OL-KR54, OL-KR55, OL-KR55B and OL-KR47B at the Olkiluoto investigation site between January 2011 and September 2011. The measuring programme employed was the same in all drillholes. The applied section lengths of the flow guide were either 2 m and 0.5 m. Flow into the drillhole or from the drillhole to the bedrock was measured within the section length. The measurements were carried out in both pumped and natural (i.e. un-pumped) conditions. The transmissivity and hydraulic head of zones were calculated from the flow and pressure results. The device used includes a sensor for single point resistance (SPR). SPR was measured in connection with the flow measurements. The electrical conductivity (EC) of fracture-specific water was measured in chosen fractures. Fractures were selected on the basis of the measured flow from fractures into the drillhole. The drillhole flow (flow along the drillhole) was measured in conjunction with drillhole EC measurements. (orig.)

  17. An approach to palaeoseismicity in the Olkiluoto (sea) area during the early holocene

    International Nuclear Information System (INIS)

    Hutri, K.L.

    2007-06-01

    Olkiluoto Island is situated in the northern Baltic Sea, near the southwestern coast of Finland, and is the proposed location of a spent nuclear fuel repository. This study examined Holocene palaeoseismicity in the Olkiluoto area and in the surrounding sea areas by computer simulations together with acoustic-seismic, sedimentological and dating methods. The most abundant rock type on the island is migmatic mica gneiss, intruded by tonalites, granodiorites and granites. The surrounding Baltic Sea seabed consists of Palaeoproterozoic crystalline bedrock, which is to a great extent covered by younger Mesoproterozoic sedimentary rocks. The area contains several ancient deep-seated fracture zones that divide it into bedrock blocks. The response of bedrock at the Olkiluoto site was modelled considering four future ice-age scenarios. Each scenario produced shear displacements of fractures with different times of occurrence and varying recovery rates. Generally, the larger the maximum ice load, the larger were the permanent shear displacements. For a basic case, the maximum shear displacements were a few centimetres at the proposed nuclear waste repository level, at proximately 500 m b.s.l. high-resolution, low-frequency echo-sounding was used to examine the Holocene submarine sedimentary structures and possible direct and indirect indicators of palaeoseismic activity in the northern Baltic Sea. Echo-sounding profiles of Holocene submarine sediments revealed slides and slumps, normal faults, debris flows and turbidite-type structures. The profiles also showed pockmarks and other structures related to gas or groundwater seepages, which might be related to fracture zone activation. Evidence of postglacial reactivation in the study area was derived from the spatial occurrence of some of the structures, especial the faults and the seepages, in the vicinity of some old bedrock fracture zones. Palaeoseismic event(s) (a single or several events) in the Olkiluoto area were dated

  18. Mise-a-la-masse surveys at Olkiluoto, 2006

    International Nuclear Information System (INIS)

    Tarvainen, A.-M.

    2007-02-01

    Suomen Malmi Oy conducted Mise-a-la-masse surveys at Olkiluoto site in Eurajoki during November and December 2006. The surveys are a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included field work, data processing and technical raporting. The report describes field operation, equipment as well as processing procedures and shows the obtained results and an analysis of their quality in the appendices. Data is delivered digitally in xyz-format. (orig.)

  19. Environmental Radioactivity Data of Olkiluoto in 1984-2001

    International Nuclear Information System (INIS)

    Ikonen, A.T.K.

    2003-04-01

    In this report, data of the environmental radiation surveillance programme of the Olkiluoto nuclear power plant is published in a collected format for further reference. The data reported consists of analysis results of selected environmental media and indicator organisms representing human food web, and it covers a period of 1984-2001. In addition to sampling and analysis results, also a concise description of data acquisition methods - when still traceable - and handling is provided as well as locations of sampling sites. (orig.)

  20. Transition from site selection to site confirmation phase: New challenge to Posiva's communication and public involvement

    International Nuclear Information System (INIS)

    Seppaelae, Timo

    2001-01-01

    In Finland, Posiva Oy is responsible for the final disposal of spent nuclear fuel. In the 1990's investigations have been carried out on four intended sites for final disposal. Posiva implemented Environmental Impact Assessment (EIA) on the investigation sites in 1997-1999. The results of the EIA procedure were published in the EIA report which was attached to the application filed to the Government in May 1999 for a policy decision on the construction of the final disposal facility in Olkiluoto in the municipality of Eurajoki. In December 2000, the Finnish Government made a favourable policy decision ( D ecision in Principle ) on the construction of final disposal facility for spent nuclear fuel in Olkiluoto. According to the decision, the facility is in line with the overall good of the society. According to the Government's decision the prerequisites of the policy decision had been met. The municipality of Eurajoki supported the construction of the facility in Olkiluoto and STUK, the Radiation and Nuclear Safety Authority, also approved of the advancement of the project. The positive policy decision of the Government will still need to be ratified by the Parliament. The parliamentary proceedings of the policy decision will probably start in February 2001. The policy decision will make it possible for Posiva to concentrate the future site confirmation studies in Olkiluoto, Eurajoki, and construct an underground research facility there. The excavation of the research facility in the bedrock is planned to start in a few years' time. The construction of the final disposal facility is scheduled to start after the year 2010. The transition from the site selection to the site confirmation phase in Eurajoki means a new challenge not only to Posiva's research work but also to Posiva's communication. In addition to meeting the safety criteria, Posiva's activities shall in the future also meet all the criteria specified by the surrounding society

  1. Results of Monitoring at Olkiluoto in 2011. Environment

    Energy Technology Data Exchange (ETDEWEB)

    Haapanen, A. [Haapanen Forest Consulting, Vanhakylae (Finland)

    2012-11-15

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2011. These summary reports have been published since 2005. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground rock characterization facility. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). Monitoring has been carried out for varying periods of time depending on the sector: some monitoring activities performed by TVO originate from the 1970s and the repository-related environmental monitoring of Olkiluoto from the early 2000s. The monitoring programme evolves according to experiences gained from the modelling work and increased understanding of the site. Monitoring activities in 2011 proceeded according to the plans. The land-use of the island continues to change due to the construction work of OL3, ONKALO and related infrastructure, but the remaining natural environment resembles other coastal locations. The amount of nitrogen in the bulk deposition increased in 2011, whereas that of sulphur decreased. Some litterfall fractions showed higher Al and Fe values than earlier, likely caused by soil dust. Proximity of the sea is seen in wet deposition and soil solution results. Soil solution also reflects the young age of soils. Undestorey vegetation has shown no essential changes during the monitoring period. Mammalian fauna on the island is typical of coastal areas in Southwestern Finland. Game catches vary according to hunting pressure and natural variation in populations. The condition of the nearby sea is affected by the continuous land uplift, the shallowness of the area, the weather conditions, the general condition of the Bothnian Sea, the nutrient and sediment loads

  2. Results of Monitoring at Olkiluoto in 2011. Environment

    International Nuclear Information System (INIS)

    Haapanen, A.

    2012-11-01

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2011. These summary reports have been published since 2005. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground rock characterization facility. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). Monitoring has been carried out for varying periods of time depending on the sector: some monitoring activities performed by TVO originate from the 1970s and the repository-related environmental monitoring of Olkiluoto from the early 2000s. The monitoring programme evolves according to experiences gained from the modelling work and increased understanding of the site. Monitoring activities in 2011 proceeded according to the plans. The land-use of the island continues to change due to the construction work of OL3, ONKALO and related infrastructure, but the remaining natural environment resembles other coastal locations. The amount of nitrogen in the bulk deposition increased in 2011, whereas that of sulphur decreased. Some litterfall fractions showed higher Al and Fe values than earlier, likely caused by soil dust. Proximity of the sea is seen in wet deposition and soil solution results. Soil solution also reflects the young age of soils. Undestorey vegetation has shown no essential changes during the monitoring period. Mammalian fauna on the island is typical of coastal areas in Southwestern Finland. Game catches vary according to hunting pressure and natural variation in populations. The condition of the nearby sea is affected by the continuous land uplift, the shallowness of the area, the weather conditions, the general condition of the Bothnian Sea, the nutrient and sediment loads

  3. Results of Monitoring at Olkiluoto in 2011. Environment

    Energy Technology Data Exchange (ETDEWEB)

    Haapanen, A. (ed.) [Haapanen Forest Consulting, Vanhakylae (Finland)

    2012-11-15

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2011. These summary reports have been published since 2005. The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground rock characterization facility. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). Monitoring has been carried out for varying periods of time depending on the sector: some monitoring activities performed by TVO originate from the 1970s and the repository-related environmental monitoring of Olkiluoto from the early 2000s. The monitoring programme evolves according to experiences gained from the modelling work and increased understanding of the site. Monitoring activities in 2011 proceeded according to the plans. The land-use of the island continues to change due to the construction work of OL3, ONKALO and related infrastructure, but the remaining natural environment resembles other coastal locations. The amount of nitrogen in the bulk deposition increased in 2011, whereas that of sulphur decreased. Some litterfall fractions showed higher Al and Fe values than earlier, likely caused by soil dust. Proximity of the sea is seen in wet deposition and soil solution results. Soil solution also reflects the young age of soils. Undestorey vegetation has shown no essential changes during the monitoring period. Mammalian fauna on the island is typical of coastal areas in Southwestern Finland. Game catches vary according to hunting pressure and natural variation in populations. The condition of the nearby sea is affected by the continuous land uplift, the shallowness of the area, the weather conditions, the general condition of the Bothnian Sea, the nutrient and sediment

  4. Thermal infrared remote sensing in assessing groundwater and surface-water resources related to Hannukainen mining development site, northern Finland

    Science.gov (United States)

    Rautio, Anne B.; Korkka-Niemi, Kirsti I.; Salonen, Veli-Pekka

    2018-02-01

    Mining development sites occasionally host complicated aquifer systems with notable connections to natural surface water (SW) bodies. A low-altitude thermal infrared (TIR) imaging survey was conducted to identify hydraulic connections between aquifers and rivers and to map spatial surface temperature patterns along the subarctic rivers in the proximity of the Hannukainen mining development area, northern Finland. In addition to TIR data, stable isotopic compositions ( δ 18O, δD) and dissolved silica concentrations were used as tracers to verify the observed groundwater (GW) discharge into the river system. Based on the TIR survey, notable GW discharge into the main river channel and its tributaries (61 km altogether) was observed and over 500 GW discharge sites were located. On the basis of the survey, the longitudinal temperature patterns of the studied rivers were found to be highly variable. Hydrological and hydrogeological information is crucial in planning and siting essential mining operations, such as tailing areas, in order to prevent any undesirable environmental impacts. The observed notable GW discharge was taken into consideration in the planning of the Hannukainen mining development area. The results of this study support the use of TIR imagery in GW-SW interaction and environmental studies in extensive and remote areas with special concerns for water-related issues but lacking the baseline research.

  5. Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Complementary evaluations of safety

    International Nuclear Information System (INIS)

    Neall, Fiona; Pastina, Barbara; Snellman, Margit; Smith, Paul; Gribi, P.; Johnson, Lawrence

    2008-12-01

    The KBS-3H design is a variant of the more general KBS-3 method for the geological disposal of spent nuclear fuel in Finland and Sweden. In the KBS-3H design, multiple assemblies containing spent fuel are emplaced horizontally in parallel, approximately 300 m long, slightly inclined deposition drifts. The copper canisters, each with a surrounding layer of bentonite clay, are placed in perforated steel shells prior to deposition in the drifts; the assembly is called the 'supercontainer'. The other KBS-3 variant is the KBS-3V design, in which the copper canisters are emplaced vertically in individual deposition holes surrounded by bentonite clay but without steel supercontainer shells. SKB and Posiva have conducted a Research, Development and Demonstration programme over the period 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to KBS-3V. As part of this programme, the long-term safety of a KBS-3H repository has been assessed in the KBS-3H safety studies. In order to focus the safety studies, the Olkiluoto site in the municipality of Eurajoki, which is the proposed site for a spent fuel repository in Finland, was used as a hypothetical site for a KBS-3H repository. The present report is part of a portfolio of reports discussing the long-term safety of the KBS-3H repository. The overall outcome of the KBS-3H safety studies is documented in the summary report, 'Safety assessment for a KBS-3H repository for spent nuclear fuel at Olkiluoto'. The purpose and scope of the KBS-3H complementary evaluations of safety report is provided in Posiva's Safety Case Plan, which is based on Regulatory Guide YVL 8.4 and on international guidelines on complementary lines of argument to long-term safety that are considered an important element of a post-closure safety case for geological repositories. Complementary evaluations of safety require the use of evaluations, evidence and qualitative supporting arguments that lie outside the

  6. Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Complementary evaluations of safety

    Energy Technology Data Exchange (ETDEWEB)

    Neall, Fiona; Pastina, Barbara; Snellman, Margit; Smith, Paul; Gribi, P.; Johnson, Lawrence

    2008-12-15

    The KBS-3H design is a variant of the more general KBS-3 method for the geological disposal of spent nuclear fuel in Finland and Sweden. In the KBS-3H design, multiple assemblies containing spent fuel are emplaced horizontally in parallel, approximately 300 m long, slightly inclined deposition drifts. The copper canisters, each with a surrounding layer of bentonite clay, are placed in perforated steel shells prior to deposition in the drifts; the assembly is called the 'supercontainer'. The other KBS-3 variant is the KBS-3V design, in which the copper canisters are emplaced vertically in individual deposition holes surrounded by bentonite clay but without steel supercontainer shells. SKB and Posiva have conducted a Research, Development and Demonstration programme over the period 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to KBS-3V. As part of this programme, the long-term safety of a KBS-3H repository has been assessed in the KBS-3H safety studies. In order to focus the safety studies, the Olkiluoto site in the municipality of Eurajoki, which is the proposed site for a spent fuel repository in Finland, was used as a hypothetical site for a KBS-3H repository. The present report is part of a portfolio of reports discussing the long-term safety of the KBS-3H repository. The overall outcome of the KBS-3H safety studies is documented in the summary report, 'Safety assessment for a KBS-3H repository for spent nuclear fuel at Olkiluoto'. The purpose and scope of the KBS-3H complementary evaluations of safety report is provided in Posiva's Safety Case Plan, which is based on Regulatory Guide YVL 8.4 and on international guidelines on complementary lines of argument to long-term safety that are considered an important element of a post-closure safety case for geological repositories. Complementary evaluations of safety require the use of evaluations, evidence and qualitative supporting arguments

  7. Aeromagnetic survey in Eurajoensalmi, Olkiluoto 2008

    International Nuclear Information System (INIS)

    Levaeniemi, H.

    2008-08-01

    This report describes the survey operation, survey and processing methods and the deliverables of an aerogeophysical survey in Olkiluoto area in April 2008. The survey was conducted by Geological Survey of Finland (GTK). The survey aircraft was a twin-engine Twin Otter operated by Finnish Aviation Academy (SIO) and owned by Natural Environment Research Council / British Geological Survey (NERC / BGS), with whom GTK has established a joint venture called Joint Airborne-geoscience Capability (JAC). The survey was conducted in April 2008 during six days. The survey consists of six separate survey flights, one of which was a magnetic calibration flight. The survey was based in Pori airport. Survey line spacing was 50 meters and nominal survey altitude was 30 meters. Measurements were completed in April 2008, and data processing and reporting was done in June 2008. Two cesium magnetometers installed onboard the aircraft (at the left wingtip and in a nose cone) were measuring the magnetic total field intensity during the survey flights. An automatic compensation unit corrected the aircraft attitude errors in the magnetic data in real time. In addition to magnetic measurement, auxiliary parameters such as flight altitude and aircraft attitude were also recorded simultaneously. Reference ground base station was used for recording the temporal variations in the magnetic field and also reference data for post-positioning of coordinate information. In the post-processing phase, heading correction, base station correction and microlevelling procedures were applied to the magnetic data. The data was exported to numeric XYZ files and interpolated into grid data file. A noteworthy local detail present in the survey and in the processing was the massive power line. For safety reasons, flight altitude had to be increased and survey lines had to be cut short in the vicinity of the powerline. However, due to reasonable planning of the survey area boundaries, this caused no great

  8. International Expert Team Concludes IAEA Peer Review of Finland's Regulatory Framework for Nuclear and Radiation Safety

    International Nuclear Information System (INIS)

    2012-01-01

    operating nuclear power units at two sites (two in Loviisa and two in Olkiluoto) and a third unit is under construction at the Olkiluoto site. - A decision in principle has been taken to build two more units, one at Olkiluoto and another at a new site. - Final low- and intermediate-level waste disposal facilities are in operation at the Loviisa and the Olkiluoto sites and interim spent fuel storage facilities are operated within operating power plants. Preparation is being made for construction of a final disposal facility for spent fuel at Olkiluoto. - Nuclear power plants generate about 30% of Finland's electricity. About IRRS Missions IRRS missions are designed to strengthen and enhance the effectiveness of the national nuclear regulatory infrastructure of States, while recognizing the ultimate responsibility of each State to ensure safety in this area. This is done through consideration of both regulatory, technical and policy issues, with comparisons against IAEA safety standards and, where appropriate, good practices elsewhere. (IAEA)

  9. Finland country report

    Energy Technology Data Exchange (ETDEWEB)

    Rantamaeki, Karin [VTT Technical Research Centre of Finland (Finland)

    2008-07-01

    Electricity share: 24.9%. Nuclear equipments: Research: 1 TRIGA Mark II; Electricity production: 4 units; Olkiluoto BWR Unit 1 (1979), Unit 2 (1982), 860 MWe (net); Loviisa PWR Unit 1 (1977), Unit 2 (1981), 490 MWe (net). Public acceptance: 43% for increase, 25% for decrease; 24%(61%) of women (men) for increase; 36%(13%) for decrease. Energy policy: new nuclear unit under construction in Olkiluoto (first EPR in the world); 2 environmental impact assessments ready, 1 pending (autumn); 1 decision-in-principle submitted, 2 expected in autumn. Nuclear waste management policy: Low- and intermediate-level wastes disposed of in underground repositories located in the bedrock at 60 to 100 m; Final disposal facility built in Olkiluoto; DiP for facility for fuel from all 5 units ratified by Parliament in 2002; Fuel encapsulated in containers placed in bedrock at 500 m; Deep underground rock characterisation and research facility (ONKALO) is under construction in Olkiluoto (ready in 2010); Excavation started in 2004; Characterisation levels at 420 m (2008) and 520 m (2009); Later used as an access route to the final repository of spent fuel which should be operational in 2020. Nuclear research: Several institutes and groups involved; Annual volume estimated to 200 ppy; Two focus areas: safety and operational performance of power plants, Management and disposal of nuclear waste; Public research in national programs; Nuclear Power Plant Safety SAFIR2010, 2007-2010; Public Research Programme on Nuclear Waste Management KYT2010, 2006-2010; EURATOM-Tekes Fusion Energy Cooperation 2007-2011; Main objective of programs is to provide authorities with high-standard expertise and results; Train new nuclear experts. The construction of the new plant and the high number of experts retiring within next 10 years has increased the needs for new personnel. The new situation also attracts students and young professionals. Nuclear energy education given at 3 universities: - Nuclear

  10. Core drilling of short drillholes at Olkiluoto in Eurajoki 2006

    International Nuclear Information System (INIS)

    Rautio, T.

    2007-05-01

    Posiva Oy submitted an application to the Finnish Government in May 1999 for the Decision in Principle to choose Olkiluoto in the municipality of Eurajoki as the site of the final disposal facility for spent nuclear fuel. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the decision in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) core drilled six short drillholes with a diameter of 75.7 mm at Olkiluoto in July - August 2006. The identification numbers of the drillholes are OL-PP51 - OL-PP56. The deviation of the drillholes was measured with the deviation measuring instruments Reflex EMS. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. The volume of the drilling water was recorded. Sodium fluorescein was used as a label agent in the drilling water. The total volume of the used drilling and flushing water were 37 m 3 . (orig.)

  11. Examination of some assumed severe reactor accidents at the Olkiluoto nuclear power plant

    International Nuclear Information System (INIS)

    Pekkarinen, E.; Rossi, J.

    1989-02-01

    Knowledge and analysis methods of severe accidents at nuclear power plants and of subsequent response of primary system and containment have been developed in last few years to the extent that realistic source tems of the specified accident sequences can be calculated for the Finnish nuclear power plants. The objective of this investigation was to calculate the source terms of off-site consequences brought about by some selected severe accident sequences initiated by the total loss of on-site and off-site AC power at the Olkiluoto nuclear power plant. The results describing the estimated off-site health risks are expressed as conditional assuming that the accident has taken place, because the probabilities of the occurence of the accident sequences considered have not been analysed in this study. The range and probabilities of occurence of health detriments are considered by calculating consequences in different weeather conditions and taking into account the annual frequency of each weather condition and statistical population distribution. The calculational results indicate that the reactor building provides and additional holdup and deposition of radioactive substance (except coble gases) released from the containment. Furthermore, the release fractions of the core inventory to the environment of volatile fission products such as iodine, cesium and tellurium remain under 0.03. No early health effects are predicted for the surrounding population in case the assumed short-tem countermeasures are performed effectively. Acute health effects are extremely improbable even without any active countermeasure. By reducing the long-term exposure from contaminated agricultural products, the collective dose from natural long-term background radiation, for instance in the sector of 30 degrees towards the southern Finland up to the distance of 300 kilometers, would be expected to increase with 2-20 percent depending on the release considered

  12. Climate scenarios for Olkiluoto on a time-scale of 120,000 years

    International Nuclear Information System (INIS)

    Pimenoff, N.; Venaelaeinen, A.; Jaervinen, H.

    2011-12-01

    Posiva Oy is planning to dispose of spent nuclear fuel in a repository, to be constructed at a depth of 400 m in the crystalline bedrock at Olkiluoto, Finland. Planning the storage requires careful consideration of many aspects, including an assessment of long-term repository safety. For estimating possible climate states at Olkiluoto on a time-scale of 120,000 years, we analyze climate simulations of an Earth System Model of Intermediate Complexity (CLIMBER-2) coupled with an ice sheet model (SICOPOLIS). The simulations into the future clearly show that the onset of the next glaciation is strongly dependent on the Earth's orbital variations and the atmospheric CO 2 concentration. It is evident that due to global warming, the climate of the next centuries will be warmer and wetter than at present. Most likely, due to global warming and low variations in the Earth's orbit around the sun, the present interglacial will last for at least the next 30,000 years. Further, the future simulations showed that the insolation minima on the Northern Hemisphere 50,000-60,000 and 90,000-100,000 years after the present hold a potential for the onset of the next glaciation. Hence, on a time-scale of 120,000 years, one must take into account climate periods lasting several thousand years having the following features: an interglacial climate, a periglacial climate, a climate with an ice sheet margin near Olkiluoto, a glacial climate with an ice sheet covering Olkiluoto, and a climate with Olkiluoto being depressed below sea level after glaciation due to isostatic depression. Due to the uncertainties related to the evolution of the future climate, it is recommended the simulations into the far future to be used only qualitatively. Quantitative information about glacial climate is achieved from the reconstructions and simulations of the past climate. (orig.)

  13. Climate scenarios for Olkiluoto on a time-scale of 100,000 years

    International Nuclear Information System (INIS)

    Pimenoff, N.; Venaelaeinen, A.; Jaervinen, H.

    2011-01-01

    Posiva Oy is planning to dispose of spent nuclear fuel in a repository, to be constructed at a depth of 400 m in the crystalline bedrock at Olkiluoto, Finland. Planning the storage requires careful consideration of many aspects, including an assessment of long-term repository safety. For estimating possible climate states at Olkiluoto on a time-scale of 100,000 years, we analyze climate simulations of an Earth System Model of Intermediate Complexity (CLIMBER-2) coupled with an ice sheet model (SICOPOLIS). The simulations into the future clearly show that the onset of the next glaciation is strongly dependent on the Earth's orbital variations and the atmospheric CO 2 concentration. It is evident that due to global warming, the climate of the next centuries will be warmer and wetter than at present. Most likely, due to global warming and low variations in the Earth's orbit around the sun, the present interglacial will last for at least the next 30,000 years. Further, the future simulations showed that the insolation minima on the Northern Hemisphere 50,000-60,000 and 90,000-100,000 years after the present hold a potential for the onset of the next glaciation. Hence, on a time-scale of 100,000 years, one must take into account climate periods lasting several thousand years having the following features: an interglacial climate, a periglacial climate, a climate with an ice sheet margin near Olkiluoto, a glacial climate with an ice sheet covering Olkiluoto, and a climate with Olkiluoto being depressed below sea level after glaciation due to isostatic depression. Due to the uncertainties related to the evolution of the future climate, it is recommended the simulations into the far future to be used only qualitatively. Quantitative information about glacial climate is achieved from the reconstructions and simulations of the past climate. (orig.)

  14. Climate scenarios for Olkiluoto on a time-scale of 120,000 years

    Energy Technology Data Exchange (ETDEWEB)

    Pimenoff, N.; Venaelaeinen, A.; Jaervinen, H. [Finnish Meteorological Institute, Helsinki (Finland)

    2011-12-15

    Posiva Oy is planning to dispose of spent nuclear fuel in a repository, to be constructed at a depth of 400 m in the crystalline bedrock at Olkiluoto, Finland. Planning the storage requires careful consideration of many aspects, including an assessment of long-term repository safety. For estimating possible climate states at Olkiluoto on a time-scale of 120,000 years, we analyze climate simulations of an Earth System Model of Intermediate Complexity (CLIMBER-2) coupled with an ice sheet model (SICOPOLIS). The simulations into the future clearly show that the onset of the next glaciation is strongly dependent on the Earth's orbital variations and the atmospheric CO{sub 2} concentration. It is evident that due to global warming, the climate of the next centuries will be warmer and wetter than at present. Most likely, due to global warming and low variations in the Earth's orbit around the sun, the present interglacial will last for at least the next 30,000 years. Further, the future simulations showed that the insolation minima on the Northern Hemisphere 50,000-60,000 and 90,000-100,000 years after the present hold a potential for the onset of the next glaciation. Hence, on a time-scale of 120,000 years, one must take into account climate periods lasting several thousand years having the following features: an interglacial climate, a periglacial climate, a climate with an ice sheet margin near Olkiluoto, a glacial climate with an ice sheet covering Olkiluoto, and a climate with Olkiluoto being depressed below sea level after glaciation due to isostatic depression. Due to the uncertainties related to the evolution of the future climate, it is recommended the simulations into the far future to be used only qualitatively. Quantitative information about glacial climate is achieved from the reconstructions and simulations of the past climate. (orig.)

  15. Safety analysis of disposal of decommissioning waste from the Olkiluoto nuclear power plant - PURKU-93

    International Nuclear Information System (INIS)

    Vieno, T.; Meszaros, F.; Nordman, H.; Taivassalo, V.

    1993-12-01

    Decommissioning waste from the Olkiluoto nuclear power plant will be disposed of at the depth between 60 and 100 meters in the bedrock at the power plant site. The existing VLJ repository for low and medium level operating waste will be extended with three new silos for the decommissioning waste of the TVO I and II reactors and the spent fuel interim store at the Olkiluoto site. Besides dismantling waste also used fuel boxes, control rods and other activated metal components accumulated during the operation of the reactors will be disposed of in the repository. The safety analysis is based on the detailed decommissioning plan of the Olkiluoto power plants and the comprehensive safety analysis carried out for the Final Safety Analysis Report of the VLJ repository. (58 refs., 31 figs., 38 tabs.)

  16. Finland: construction of the first geological storage of the world; Finlandia: construccion del primer almacen geologico del mundo

    Energy Technology Data Exchange (ETDEWEB)

    Garcia Neri, E.

    2015-07-01

    Finland has become the first country in the world granting a construction license for a store deep geological (AGP) for radioactive waste, as reported last November 12 Posiva, the agency management of these materials in the Baltic country. After more than 40 years of research, Posiva begin construction of this facility in Olkiluoto, which will house so end spent fuel generated in power stations Olkiluoto and Loviisa and could start operating in 2023. As noted Janne Mokka, president of Posiva, this pioneering project is not only important for Finland, but for everyone because it is the first AGP enters under construction in the world. (Author)

  17. Seismic VSP and HSP surveys on preliminary investigation areas in Finland for final disposal of spent nuclear fuel

    International Nuclear Information System (INIS)

    Keskinen, J.; Cosma, C.; Heikkinen, P.

    1992-10-01

    Seismic reflection surveys in boreholes were carried out for Teollisuuden Voima Oy at five sites in Finland (Eurajoki Olkiluoto, Hyrynsalmi Veitsivaara, Konginkangas Kivetty, Kuhmo Romuvaara and Sievi Syyry). The vertical Seismic Profiling (VSP) surveys were a part of the investigation programme for the final disposal of spent nuclear fuel. The purpose was to detect fractured zones, lithological contacts and other anomalies in the structure of the rockmass and to determine their position and orientation. Horizontal Seismic Profiling (HSP) was used at the Olkiluoto site, additionally to VSP. The data has been organized in profiles containing seismograms recorded from the same shotpoint (shot gathers). One of the most powerful processing methods used with this project has been the Image Space Filtering, a new technique, which has been developed (in the project) for seismic reflection studies in crystalline rock. The method can be applied with other rock types where steeply inclined or vertical anomalies are of interest. It acts like a multichannel filter, enhancing the reflected events and also as an interpretation tool, to estimate the strength and position of the reflectors. This approach has been of great help in emphasizing the weak reflections from uneven and sometimes vanishing interfaces encountered in crystalline

  18. Lithological and structural bedrock model of the Haestholmen study site, Loviisa, SE Finland

    International Nuclear Information System (INIS)

    Front, K.; Paulamaeki, S.; Ahokas, H.; Anttila, P.

    1999-10-01

    The Haestholmen study site is located within the anorogenic Wiborg rapakivi granite batholith, 1640 1630 Ma in age. The bedrock consists of various rapakivi granites, which can be divided into three groups or lithological units: (1) wiborgite and pyterlite, (2) porphyritic rapakivi granite, and (3) even-grained or weakly porphyritic rapakivi granite, pyterlite being the dominant rock type. The evengrained and weakly porphyritic rapakivi granite has been interpreted to form a younger intrusive unit with a thickness of ca. 500 m, dipping approx. 20 deg to the NNW-NNE. Surface fractures form a distinct orthogonal system, with three perpendicular fracture directions: fractures dipping steeply (dip >75 deg) to the NE-SW and NW-SE plus subhorizontal (dip -3 m 2 /s to 1*10 -7 m 2 /s, the average being 1-10 -5 m 2 /s. (orig.)

  19. Remote sensing supported surveillance and characterization of tailings behavior at a gold mine site, Finland.

    Science.gov (United States)

    Rauhala, Anssi; Tuomela, Anne; Rossi, Pekka M.; Davids, Corine

    2017-04-01

    The management of vast amounts of tailings produced is one of the key issues in mining operations. The effective and economic disposal of the waste requires knowledge concerning both basic physical properties of the tailings as well as more complex aspects such as consolidation behavior. The behavior of tailings in itself is a very complex issue that can be affected by flocculation, sedimentation, consolidation, segregation, deposition, freeze-thaw, and desiccation phenomena. The utilization of remote sensing in an impoundment-scale monitoring of tailings could benefit the management of tailings, and improve our knowledge on tailings behavior. In order to gain better knowledge of tailings behavior in cold climate, we have utilized both modern remote sensing techniques and more traditional in situ and laboratory measurements in characterizing thickened gold tailings behavior at a Finnish gold mine site, where the production has been halted due to low gold prices. The remote sensing measurements consisted of elevation datasets collected from unmanned aerial vehicles during summers 2015 and 2016, and a further campaign is planned for the summer 2017. The ongoing traditional measurements include for example particle-size distribution, frost heave, frost depth, water retention, temperature profile, and rheological measurements. Initial results from the remote sensing indicated larger than expected settlements on parts of the tailings impoundment, and also highlighted some of the complexities related to data processing. The interpretation of the results and characterization of the behavior is in this case complicated by possible freeze-thaw effects and potential settlement of the impoundment bottom structure consisting of natural peat. Experiments with remote sensing and unmanned aerial vehicles indicate that they could offer potential benefits in frequent mine site monitoring, but there is a need towards more robust and streamlined data acquisition and processing. The

  20. Summary report of the experiences from TVO's site investigations

    International Nuclear Information System (INIS)

    Oehberg, A.; Saksa, P.; Ahokas, H.; Ruotsalainen, P.; Snellman, M.

    1994-09-01

    In 1992 Teollisuuden Voima Oy (TVO) completed preliminary site investigations for radioactive waste disposal at five sites in Finland. The aim of this report was the compilation of the experiences from TVO's site investigations. The main interest was focused on investigation strategies and the most important investigation methods for the conceptual modelling. The objective of the preliminary site investigations was to obtain data on the bedrock properties in order to evaluate the areas. The programme was divided into four stages, each stage having its own subobjective. The site-specific investigation programme for each site included a large common part and a small site-specific part. The strategies (objectives) and experiences from different disciplines, geology, hydrogeochemistry, geophysics and geohydrology, are presented in the report. The conceptual modelling work procedure including both bedrock and groundwater modelling is described briefly using the Olkiluoto site as an example. Each of the other areas has undergone similar phases of work. (52 refs., 45 figs., 5 tabs.)

  1. Investigation plan for infiltration experiment in Olkiluoto

    International Nuclear Information System (INIS)

    Lehtinen, A.; Lindgren, S.; Ikonen, A.

    2008-11-01

    A three-year field experiment to investigate potential changes in pH and redox conditions, and in buffering capacity as well as the hydrogeochemical processes related to groundwater infiltration is designed for implementation in the vicinity of ONKALO. The idea is to monitor the major infiltration flow path from the ground surface into the upper part of ONKALO at about 50 to 100 m depth depending on the observations made during the experiment. The geochemical evolution of the groundwater is strongly affected by infiltration from the surface. In natural conditions in Olkiluoto most of the geochemical reactions occur along the first few tens of metres of the flow path, in an interface between anaerobic and aerobic conditions. The dissolved aggressive agents, CO 2 and O 2 , of the infiltrating water are consumed and the hydrogeochemistry stabilises on neutral and anaerobic conditions due to weathering processes. As a consequence of this evolution, reaction fronts are formed in the flow channels between acid-neutral and aerobic-anaerobic interfaces. The construction of ONKALO may, however, increase the hydraulic gradient and flow into bedrock, which can move these fronts to deeper depths and decrease the buffering capacity of the rock fractures against surficial water infiltration. Detailed integration of hydrogeochemical (including microbiology), geological and hydrogeological studies is essential for a successful experiment. Accurate hydrogeochemical and hydrogeological data that will be collected during this experiment are used in coupled modelling exercises (P/O studies in site reports), which will be carried out to evaluate the movements of the reaction fronts and the buffering capacity of Olkiluoto bedrock against surficial water infiltration. Good quality information is also necessary for calibrating predictive calculations for the safety case estimating future evolution of the site. In addition to the geochemical targets, the experiment can be used in

  2. GPS operations at Olkiluoto in 2009

    Energy Technology Data Exchange (ETDEWEB)

    Kallio, U.; Nyberg, S.; Koivula, H.; Jokela, J.; Poutanen, M.; Ahola, J. (Finnish Geodetic Institute, Masala (Finland))

    2010-06-15

    The GPS based deformation studies have been made at the investigation areas of Posiva since 1995, when the network of ten GPS pillars was established at Olkiluoto. One pillar in the investigation area belongs to the Finnish permanent GPS network, FinnRef. 28 GPS measurement campaigns have been carried out at Olkiluoto since 1995. According to the time series of the GPS results 1/3 of the baselines at Olkiluoto have statistically significant change rates. However, the observed movements are smaller than +-0.20 mm/a. There are five pillars, which have statistically significant horizontal velocities at Olkiluoto. These local velocity components are small but taking into account the standard deviations the largest velocity components seems to be reliably determined. At Olkiluoto a baseline for electronic distance measurements (EDM) was built in 2002. The baseline has been measured using EDM instruments in connection to the GPS observations. Changes in he difference between the GPS and EDM results indicate the systematic change in GPS results. No corrections based on only one baseline were not applied to GPS vectors. The GPS network at Olkiluoto was extended in 2003. The new pillars were built close to Kuivalahti village and on a small island of Iso Pyrekari. According to the geological evidence it is expected that a fracture zone is located between the new stations, thus enabling the determination of possible deformations along the fracture zone. The new pillars have been observed since 2003 and now we have computed the first deformation analysis from the six years data. Four new permanent stations will be established in summer 2010 at Olkiluoto. We have automated the processing of the campaign data by using the Bernese processing engine (BPE) together with our own Perl scripts. The local crustal deformations have been studied in GeoSatakunta project, too. This GPS network is located in Cities of Pori and Rauma and their neighbouring municipalities. Two new pillars

  3. GPS operations at Olkiluoto in 2009

    International Nuclear Information System (INIS)

    Kallio, U.; Nyberg, S.; Koivula, H.; Jokela, J.; Poutanen, M.; Ahola, J.

    2010-06-01

    The GPS based deformation studies have been made at the investigation areas of Posiva since 1995, when the network of ten GPS pillars was established at Olkiluoto. One pillar in the investigation area belongs to the Finnish permanent GPS network, FinnRef. 28 GPS measurement campaigns have been carried out at Olkiluoto since 1995. According to the time series of the GPS results 1/3 of the baselines at Olkiluoto have statistically significant change rates. However, the observed movements are smaller than ±0.20 mm/a. There are five pillars, which have statistically significant horizontal velocities at Olkiluoto. These local velocity components are small but taking into account the standard deviations the largest velocity components seems to be reliably determined. At Olkiluoto a baseline for electronic distance measurements (EDM) was built in 2002. The baseline has been measured using EDM instruments in connection to the GPS observations. Changes in he difference between the GPS and EDM results indicate the systematic change in GPS results. No corrections based on only one baseline were not applied to GPS vectors. The GPS network at Olkiluoto was extended in 2003. The new pillars were built close to Kuivalahti village and on a small island of Iso Pyrekari. According to the geological evidence it is expected that a fracture zone is located between the new stations, thus enabling the determination of possible deformations along the fracture zone. The new pillars have been observed since 2003 and now we have computed the first deformation analysis from the six years data. Four new permanent stations will be established in summer 2010 at Olkiluoto. We have automated the processing of the campaign data by using the Bernese processing engine (BPE) together with our own Perl scripts. The local crustal deformations have been studied in GeoSatakunta project, too. This GPS network is located in Cities of Pori and Rauma and their neighbouring municipalities. Two new pillars

  4. Summary report - development of laboratory tests and the stress- strain behaviour of Olkiluoto mica gneiss

    Energy Technology Data Exchange (ETDEWEB)

    Hakala, M.; Heikkilae, E. [Helsinki Univ. of Technology, Espoo (Finland). Lab. of Rock Engineering

    1997-05-01

    This work summarizes the project aimed at developing and qualifying a suitable combination of laboratory tests to establish a statistically reliable stress-strain behaviour of the main rock types at Posiva Oy`s detailed investigation sites for disposal of spent nuclear fuel. The work includes literature study of stress-strain behaviour of brittle rock, development and qualification of laboratory tests, suggested test procedures and interpretation methods and finally testing of Olkiluoto mica gneiss. The Olkiluoto study includes over 130 loading tests. Besides the commonly used laboratory tests, direct tensile tests, damage controlled tests and acoustic emission measurements were also carried out. (orig.) (54 refs.).

  5. Summary report - development of laboratory tests and the stress- strain behaviour of Olkiluoto mica gneiss

    International Nuclear Information System (INIS)

    Hakala, M.; Heikkilae, E.

    1997-05-01

    This work summarizes the project aimed at developing and qualifying a suitable combination of laboratory tests to establish a statistically reliable stress-strain behaviour of the main rock types at Posiva Oy's detailed investigation sites for disposal of spent nuclear fuel. The work includes literature study of stress-strain behaviour of brittle rock, development and qualification of laboratory tests, suggested test procedures and interpretation methods and finally testing of Olkiluoto mica gneiss. The Olkiluoto study includes over 130 loading tests. Besides the commonly used laboratory tests, direct tensile tests, damage controlled tests and acoustic emission measurements were also carried out. (orig.) (54 refs.)

  6. Reactive transport predictions for an Olkiluoto. Final repository tunnel unit

    International Nuclear Information System (INIS)

    Luukkonen, A.; Nordman, H.

    2007-09-01

    The presented hydrogeochemical reactive transport calculations concentrate to a defined unit piece (unit cell) of the planned Olkiluoto repository that is under design for spent nuclear fuel. The material properties assigned to the tunnel unit are based on literature as far as possible. Calculations make up geochemical future scenarios on the repository evolution. Most recent predictions on the potential future climate at Olkiluoto are utilised together with estimates how future hydraulic conditions affect the repository. Two climate scenarios are considered in detail. The Weichselian-R scenario is based on the repetition of the last glacial cycle, while the Emissions-M scenario attempts to predict the future groundwater conditions at Olkiluoto in the situation where the atmospheric greenhouse gasses delay the next glacial cycle at least for 100,000 years. The groundwater compositions, considered active at the repository depth in future, are judged in this study. Several geochemical processes are considered active at the repository depth. Calculations concentrate on the changes occurring with time within the tunnel unit. All simulations are done in geochemically reducing conditions. It turns out that sulphur cycling in these conditions is in central role considering the safety assessment studies of Olkiluoto repository. Furthermore, groundwater salinity and cation occupancy within the exchange sites of montmorillonite contributes to sealing properties of the engineered barrier system. Calculations attempt to estimate effects of possible future scenarios for the Olkiluoto repository. The results indicate that the buffer capacities assigned to the tunnel unit are large enough, at least to next 100,000 years, to maintain dissolved sulphide contents low in the groundwater infiltrating through the tunnel engineered barrier system. Geochemical reactions raise the bicarbonate levels within the groundwater. This is a useful buffer if low pH conditions emerge in the

  7. Lithological and structural bedrock model of the Haestholmen study site, Loviisa, SE Finland

    Energy Technology Data Exchange (ETDEWEB)

    Front, K.; Paulamaeki, S.; Ahokas, H.; Anttila, P

    1999-10-01

    The Haestholmen study site is located within the anorogenic Wiborg rapakivi granite batholith, 1640 1630 Ma in age. The bedrock consists of various rapakivi granites, which can be divided into three groups or lithological units: (1) wiborgite and pyterlite, (2) porphyritic rapakivi granite, and (3) even-grained or weakly porphyritic rapakivi granite, pyterlite being the dominant rock type. The evengrained and weakly porphyritic rapakivi granite has been interpreted to form a younger intrusive unit with a thickness of ca. 500 m, dipping approx. 20 deg to the NNW-NNE. Surface fractures form a distinct orthogonal system, with three perpendicular fracture directions: fractures dipping steeply (dip >75 deg) to the NE-SW and NW-SE plus subhorizontal (dip <30 deg) fractures. The fracturing in the outcrops is sparse,the average fracture frequency being 0.6 fractures/m. The majority of the fractures in the drill cores are horizontal or very gently dipping and there is no difference in fracture orientations in regard to rock type or depth. Core samples are usually slightly fractured (1 - 3 fractures/m), even-grained rapakivi granites being in places abundantly fractured (3 10 fractures/m. The broken sections in Haestholmen core samples represent about 4.6 % of the total length of the samples. Calcite, dolomite, Fe- hydroxides and clay minerals (illite, montmorillonite and kaolinite) form the most typical fracture mineral phases throughout the drill cores. Core discing is locally seen as repeated fracture-like subparallel cracks in core with spacing of about some millimetres to tens of millimetres. The structural model contains 27 structures (denoted by the term R+number), more than half of which have been verified by direct observations from boreholes or from the VLJ repository. The remaining structures are mainly based on the geophysical interpretation, and have been classified as probable or possible fracture zones. In addition, local structures with uncertain orientation

  8. Seismic signal in Olkiluoto. Preliminary comparison of underground and surface recordings

    International Nuclear Information System (INIS)

    Saari, J.; Malm, M.

    2015-02-01

    Seismic hazard studies in Finland relate to nuclear power plant sites on the Earth's surface. The impact of seismic waves is different on structures on the surface than underground. The purpose of this study is to approximate how ground motions recorded in the ONKALO compare with those on the surface above the ONKALO. Broadband seismometers were installed on the surface and at the depth of 400 m inside the ONKALO in November 2013. The operation time of the seismometers was about nine months. The analysed signals included background noise, teleseismic earthquakes, regional earthquake, local explosions and explosions from the ONKALO site. The studies in Olkiluoto demonstrated that, in general, there is a de-amplification of ground motions in the ONKALO relative to those on the surface, or there is no significant difference between the recordings. The result is likely associated with the type of the seismic source and the relatively shallow depth (400 m) of the underground station. Observed relative amplification related only to nearfield events: the recorded velocity amplitudes on the surface were 2 - 10 times larger than underground. One opposite relation was found in the study: the vertical component of the velocity amplitude of a regional earthquake seems to be about three times larger in ONKALO than on the surface between frequencies 50 Hz and 80 Hz. Definite conclusions concerning amplification or de-amplification cannot be based on the result of this study. In practice, any set of recordings cannot give a comprehensive description of the possible variations, like how the wavefield reflected from the surface interacts with the wavefield coming towards the surface. Numerical modeling is suggested for further studies of this subject. (orig.)

  9. Migmatites and migmatite-like rocks of Olkiluoto

    International Nuclear Information System (INIS)

    Kaerki, A.

    2015-02-01

    Bedrock of the Olkiluoto Island in the western end of the Palaeoproterozoic Svecofennian Accretionary Arc Complex, SW Finland is composed of high-grade metamorphic pelites, arenites and intermediate, arc type metavolcanic rocks intruded by granodioritic to tonalitic plutonic rocks. Regional metamorphism culminated with voluminous migmatization in the temperature of 660 - 700 deg C and relatively low pressure of about 3.5 - 4 kbar. The end result of polyphase metamorphism and deformation is a metamorphic rock succession composed of diverse migmatite rocks, metatexites and diatexites. Metatexites are migmatites in which several, discrete components can be detected, and in which the paleosome with some pre-partial-melting textures is identifiable. Diatexites are more advanced migmatites in which the pre-migmatization structures are often totally destroyed and the rock is dominated by different neosome components meaning leucosome, melanosome or mesosome. Based on the migmatite structures the metatexites of Olkiluoto have been classified into six subgroups. Dike-structured metatexites are composed of well preserved paleosome intruded by one single set of narrow, subparallel leucosome dikes which cover ca. 5 - 10 % of the whole rock volume. Net-structure is composed of a network of narrow leucosome dikes which show a reticulated structure in a plane section and cover less than 30 % of the whole rock volume. Breccia-structure is composed of angular or rounded paleosome blocks surrounded by moderate amount of leucosome. Patch-structure is composed of irregular leucosome patches which intruded the well preserved paleosome and compose typically 20 - 70 % of the rock volume. Layer-structure is characterized by more or less regular leucosome dikes sub-parallel to the foliation of the well preserved paleosome. Vein-structured metatexites and also diatexites include a set of pipe-like, longish leucosome veins most probably generated by synchronous melting and deformation

  10. Migmatites and migmatite-like rocks of Olkiluoto

    Energy Technology Data Exchange (ETDEWEB)

    Kaerki, A. [Kivitieto Oy, Oulu (Finland)

    2015-02-15

    Bedrock of the Olkiluoto Island in the western end of the Palaeoproterozoic Svecofennian Accretionary Arc Complex, SW Finland is composed of high-grade metamorphic pelites, arenites and intermediate, arc type metavolcanic rocks intruded by granodioritic to tonalitic plutonic rocks. Regional metamorphism culminated with voluminous migmatization in the temperature of 660 - 700 deg C and relatively low pressure of about 3.5 - 4 kbar. The end result of polyphase metamorphism and deformation is a metamorphic rock succession composed of diverse migmatite rocks, metatexites and diatexites. Metatexites are migmatites in which several, discrete components can be detected, and in which the paleosome with some pre-partial-melting textures is identifiable. Diatexites are more advanced migmatites in which the pre-migmatization structures are often totally destroyed and the rock is dominated by different neosome components meaning leucosome, melanosome or mesosome. Based on the migmatite structures the metatexites of Olkiluoto have been classified into six subgroups. Dike-structured metatexites are composed of well preserved paleosome intruded by one single set of narrow, subparallel leucosome dikes which cover ca. 5 - 10 % of the whole rock volume. Net-structure is composed of a network of narrow leucosome dikes which show a reticulated structure in a plane section and cover less than 30 % of the whole rock volume. Breccia-structure is composed of angular or rounded paleosome blocks surrounded by moderate amount of leucosome. Patch-structure is composed of irregular leucosome patches which intruded the well preserved paleosome and compose typically 20 - 70 % of the rock volume. Layer-structure is characterized by more or less regular leucosome dikes sub-parallel to the foliation of the well preserved paleosome. Vein-structured metatexites and also diatexites include a set of pipe-like, longish leucosome veins most probably generated by synchronous melting and deformation

  11. Optical imaging of borehole PR10 at Olkiluoto 2006

    International Nuclear Information System (INIS)

    Tarvainen, A.-M.

    2007-03-01

    Suomen Malmi Oy carried out optical imaging of borehole PR10 at Olkiluoto site in Eurajoki during December 2006. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and the data processing. This report describes the field operation, the equipment as well as the processing procedures and shows the obtained results and their quality. The raw and processed data are delivered digitally in WellCAD and PDF format. (orig.)

  12. Forsmark site investigation. Bedrock geology - overview and excursion guide

    Energy Technology Data Exchange (ETDEWEB)

    Stephens, Michael B. (Geological Survey of Sweden, Uppsala (Sweden))

    2010-09-15

    Bearing in mind the significance of the bedrock data from the ground surface for the geological 3D modelling work, SKB decided to present excursion guides that serve in the demonstration of the bedrock geology at the ground surface in both the Forsmark (this guide) and Laxemar-Simpevarp areas. An excursion guide is also available for the Olkiluoto area in south-western Finland, which has been selected for the construction of a repository for the disposal of highly radioactive, spent nuclear fuel in Finland. The current excursion guide presents the bedrock geology and describes in detail the character of the bedrock at ten representative outcrops or outcrop areas at the ground surface in the site investigation area at Forsmark. All localities are located within or immediately adjacent to the proposed repository volume selected by SKB

  13. Forsmark site investigation. Bedrock geology - overview and excursion guide

    International Nuclear Information System (INIS)

    Stephens, Michael B.

    2010-09-01

    Bearing in mind the significance of the bedrock data from the ground surface for the geological 3D modelling work, SKB decided to present excursion guides that serve in the demonstration of the bedrock geology at the ground surface in both the Forsmark (this guide) and Laxemar-Simpevarp areas. An excursion guide is also available for the Olkiluoto area in south-western Finland, which has been selected for the construction of a repository for the disposal of highly radioactive, spent nuclear fuel in Finland. The current excursion guide presents the bedrock geology and describes in detail the character of the bedrock at ten representative outcrops or outcrop areas at the ground surface in the site investigation area at Forsmark. All localities are located within or immediately adjacent to the proposed repository volume selected by SKB

  14. Precise levelling campaigns at Olkiluoto in 2006 - 2007

    International Nuclear Information System (INIS)

    Lehmuskoski, P.

    2008-04-01

    The GPS observation network of Olkiluoto was constructed in 1994 for monitoring crustal deformations in the investigation area. To fulfil a better vertical control of the GPS network, precise levellings were started in the area in autumn 2003. The GPS network was first connected at Lapijoki to the precise levelling network of Finland to control the vertical movements of the whole island of Olkiluoto. Then the GPS network was levelled. It consisted of the reserve marks of eight GPS pillars and five levelling bench marks, two of which constituted the nodal bench mark pair. The second precise levelling campaign on the area was carried out in autumn 2005. Now only the GPS network added with the antenna platforms of nine GPS pillars were levelled. Compared to the other points, the elevation difference of two reserve mark pairs had changed significantly during two years, about one millimetre. The reason may be the blasting of the rock in the neighbourhood of these points and deformation of the rock after the blasting. Inspired by the observed elevation changes in 2005, micro loops were established and levelled onto the ONKALO and the VLJ Repository in autumn 2006. The micro loops consisted of seven and five bench marks the mean interval being about 300 metres. The campaign in autumn 2007 consisted of the levellings of all measured and undestroyed points of the earlier campaigns. The most interesting results were: (1) Compared to the mean theoretical land uplift the nodal bench mark 03216 near the crossing of Olkiluodontie and Satamatie had risen in four years 2.6 mm more than the nodal bench mark of Lapijoki and 1.9 mm of this occurred within the 0.8 mm long interval which separates the island and the continent. (2) During four years the northern part of the island had risen about one millimetre more than the middle part, where the before mentioned 03216 is located. (3) The elevation differences between the bench marks of the ONKALO micro loop were changed even one

  15. ONKALO 3D tunnel seismic investigations at Olkiluoto in 2009

    International Nuclear Information System (INIS)

    Cosma, C.; Enescu, N.; Balu, L.; Jacome, M.

    2011-02-01

    POSIVA Oy conducts bedrock investigations at the spent nuclear fuel final disposal site at Olkiluoto, in western Finland. The excavation of the access tunnel to the repository hosts the ONKALO underground rock characterization facility. The investigations carried out at ONKALO focus on the bedrock and groundwater conditions prevailing on the final disposal site and how construction work affects them. Tunnel seismic investigations were carried out in July 2009, as an extension of similar work performed in December 2007. The main objective of the tunnel seismic investigations have been to demonstrate the possibility to detect, locate and image cost effectively steeply and gently dipping fractures, at the side and/or below the tunnel and to characterize the volume of rock surrounding a 250 m long segment of the ONKALO tunnel. The survey was conducted at a depth of 350 m, over a 240 m long line of 3-components receivers, spaced at 3m intervals. Seismic signals were produced along two lines, on the tunnel wall and floor, with source points spaced at 1m. A timedistributed swept-impact, the Vibsist-250 hydraulic source, was used. The source was hosted on a mini excavator. Receiver holes approximately 0.4 m deep were drilled prior to the survey, horizontally into the tunnel wall. One of the procedures used for data stacking and migration is based on a proprietary method combining the DMO (Dip Move Out) correction and an expression of the Radon Transform. Horizontal and vertical migrated profiles were computed both for the P wave and S wave reflected wave fields. A true 3D migration technique (Image Point migration) was used to create 3D migrated sections oriented to incremental azimuths around the tunnel, the result being a cylindrical imaging volume. A general conclusion is that seismic surveys along the tunnel can economically be used for rock mass characterization. High quality results can be obtained by operations in tunnel working conditions, provided that due

  16. IAEA coordinated research project (CRP). The use of selected safety indicators (concentrations, fluxes) in the assessment of radioactive waste disposal. Report 7: Site-specific natural geochemical concentrations and fluxes at four repository investigation sites in Finland for use as indicators of nuclear waste repository safety

    International Nuclear Information System (INIS)

    Pitkaenen, P.; Loefman, J.; Luukkonen, A.; Partamies, S.

    2003-01-01

    This report concerns site-specific data achieved during the studies of four Finnish candidate sites for nuclear fuel repository. The aims are to examine the level of radioactive concentrations (U, Rn, K, Rb, Cs, Ra, Th), their sources and their fluxes at different sites and at different depths, and whether differences in chemical conditions result from the geology or hydrogeology. The sites cover virtually the formation history of Finnish Precambrian bedrock and differ geochemically significantly. Romuvaara represents Archean basement gneisses with low K and U contents. Proterozoic migmatitic mica gneisses at Olkiluoto represent a very reducing geochemical environment with graphite and sulphides. Oxidising conditions have characterised the formation of early synkinematic granitoids at Kivetty and as well as anorogenic rapakivi granite Haestholmen. Particularly the rapakivi granite is enriched with incompatible elements such as K, Rb, U and Th. Hydrogeologically the sites differ as well. The inland sites, Romuvaara and Kivetty, have been above the highest shoreline since the retreat of the ice of the Weichselian glaciation, whereas the coastal sites have been below sea level. Hydraulic gradient is also higher inland than on shore. The contents of radioactive elements vary significantly between the sites and between deep and shallow groundwaters. Uranium concentrations at each site decrease mainly with the increasing depth, and they correlate relatively with bedrock contents between the sites. However, the observed exceptionally low contents are considered to result from a short water-rock interaction time in shallow groundwaters at Kivetty and from actively reducing groundwater conditions in deep groundwaters at Olkiluoto. Radon contents correlate mainly with U-concentrations, suggesting that Rn derives predominantly from dissolved U. Potassium and rubidium concentrations correlate with salinity, indicating that their main source is seawater or ancient brine

  17. Membership Finland

    CERN Multimedia

    Rubbia,C

    1991-01-01

    Le DG C.Rubbia et la vice présidente du conseil du Cern souhaite la bienvenue à l'adhésion de la Finlande, comme 15me membre du Cern depuis le 1. janvier 1991 en présence du secrétaire generale et de l'ambassadeur

  18. Analysis of temperature data at the Olkiluoto

    Energy Technology Data Exchange (ETDEWEB)

    Sedighi, M.; Bennett, D.; Masum, S.; Thomas, H. [Cardiff Univ. (United Kingdom); Johansson, E. [Saanio and Riekkola Oy, Helsinki (Finland)

    2014-03-15

    As part of the rock mechanics monitoring programme 2012 at Olkiluoto, temperature data have been recorded. Temperature data have been measured, collected and monitored at the Olkiluoto site and in ONKALO in various locations, by different methods and in conjunction with other investigations carried out at the site. This report provides a detailed description of the investigation and analysis carried out on temperature datasets. This report aims to provide a better understanding of the in-situ temperature of the rock and soil at the site. Three categories of datasets have been analysed and studied from the Posiva thermal monitoring programme. These consist of: (i) data collected from the various drillholes during geophysical logging and Posiva Flow Log (PFL) measurements, (ii) measurements in the ONKALO ramp, the investigation niche located at elevation -140 m and a technical room located at 437 m below the surface, and (iii) surface temperature measurements from four weather stations and four measurement ditches. Time-series data obtained from the groundwater temperature measurements during the 'Posiva Flow Log' (PFL) tests in drillholes OL-KR1 to KR55 at different depths and years have been analysed. Temperature at a depth of 400 m was found to be in the range of 10 to 11 deg C. The geothermal gradient obtained from the PFL data without pumping was found to be approximately 1.4 deg C/100m with relatively uniform temporal and spatial patterns at the repository depth, i.e. at 400 m.The geothermal gradient obtained from the results of the PFL measurements and geophysical loggings indicate similar temperature values at the repository depths, i.e. 400 m. The characteristics of the time series data related to the ONKALO measurements, have been obtained through a series of Non-uniform Discrete Fourier Transform analysis Datasets related to the various chainages and investigation niche at ONKALO have been studied. The largest variation in the temperature

  19. Analysis of temperature data at the Olkiluoto

    International Nuclear Information System (INIS)

    Sedighi, M.; Bennett, D.; Masum, S.; Thomas, H.; Johansson, E.

    2014-03-01

    As part of the rock mechanics monitoring programme 2012 at Olkiluoto, temperature data have been recorded. Temperature data have been measured, collected and monitored at the Olkiluoto site and in ONKALO in various locations, by different methods and in conjunction with other investigations carried out at the site. This report provides a detailed description of the investigation and analysis carried out on temperature datasets. This report aims to provide a better understanding of the in-situ temperature of the rock and soil at the site. Three categories of datasets have been analysed and studied from the Posiva thermal monitoring programme. These consist of: (i) data collected from the various drillholes during geophysical logging and Posiva Flow Log (PFL) measurements, (ii) measurements in the ONKALO ramp, the investigation niche located at elevation -140 m and a technical room located at 437 m below the surface, and (iii) surface temperature measurements from four weather stations and four measurement ditches. Time-series data obtained from the groundwater temperature measurements during the 'Posiva Flow Log' (PFL) tests in drillholes OL-KR1 to KR55 at different depths and years have been analysed. Temperature at a depth of 400 m was found to be in the range of 10 to 11 deg C. The geothermal gradient obtained from the PFL data without pumping was found to be approximately 1.4 deg C/100m with relatively uniform temporal and spatial patterns at the repository depth, i.e. at 400 m.The geothermal gradient obtained from the results of the PFL measurements and geophysical loggings indicate similar temperature values at the repository depths, i.e. 400 m. The characteristics of the time series data related to the ONKALO measurements, have been obtained through a series of Non-uniform Discrete Fourier Transform analysis Datasets related to the various chainages and investigation niche at ONKALO have been studied. The largest variation in the temperature amplitude of data

  20. Structure and geological evolution of the bedrock at southern Satakunta, SW Finland

    Energy Technology Data Exchange (ETDEWEB)

    Paulamaeki, S.; Paananen, M.; Elo, S. [Geological Survey of Finland (Finland)

    2002-02-01

    The southern Satakunta area lies on the west coast of Finland, mainly covering the mainland (with main towns Pori and Rauma), but also including the coastal archipelago and part of the Bothnian Sea. Near the centre of the area lies the island of Olkiluoto, on which Finland's site for a deep repository for spent nuclear fuel is located. The purpose of the present report is to compile and interpret all available geological and geophysical data relevant to understanding the regional geological setting of the Olkiluoto site. The area described is covered by four 1:100 000 scale geological map sheets, published by the Geological Survey of Finland, which, together with low-altitude aeromagnetic maps, provide the basis for a new 1:250 000 geological map compilation. This shows that the bedrock of southern Satakunta can be subdivided into three main zones: a pelitic migmatite belt in the southwest, a central, NW-SE trending area of sandstone, and a psammitic migmatite belt in the northeast. The migmatite belts formed during the Svecofennian orogeny, 1900-1800 Ma ago (Palaeoproterozoic). The sandstone area is the remnant of an alluvial basin, preserved now in a NW-SE trending graben, bounded on both sides by normal fault zones. The sandstones are thought to be at least 1400-1300 Ma old (Mesoproterozoic), and they are cut by Postjotnian olivine diabase dykes, 1270-1250 Ma in age. The Svecofennian migmatite belts show a complex history of formation, with various phases of anatexis/metamorphism, deformation and intrusion. In the pelitic migmatite belt, in which the Olkiluoto site is situated, four phases of ductile deformation (D-D4) and two phases of regional highT/lowP metamorphism and migmatite formation can be recognised, together with synorogenic (tonalite, granodiotite) and late orogenic ( potassium granite) intrusions. Subsequently, this very heterogeneous complex was intruded by anorogenic rapakivi granites, with ages 1580-1550 Ma. One pluton, the Eurajoki stock

  1. Structure and geological evolution of the bedrock at southern Satakunta, SW Finland

    International Nuclear Information System (INIS)

    Paulamaeki, S.; Paananen, M.; Elo, S.

    2002-02-01

    The southern Satakunta area lies on the west coast of Finland, mainly covering the mainland (with main towns Pori and Rauma), but also including the coastal archipelago and part of the Bothnian Sea. Near the centre of the area lies the island of Olkiluoto, on which Finland's site for a deep repository for spent nuclear fuel is located. The purpose of the present report is to compile and interpret all available geological and geophysical data relevant to understanding the regional geological setting of the Olkiluoto site. The area described is covered by four 1:100 000 scale geological map sheets, published by the Geological Survey of Finland, which, together with low-altitude aeromagnetic maps, provide the basis for a new 1:250 000 geological map compilation. This shows that the bedrock of southern Satakunta can be subdivided into three main zones: a pelitic migmatite belt in the southwest, a central, NW-SE trending area of sandstone, and a psammitic migmatite belt in the northeast. The migmatite belts formed during the Svecofennian orogeny, 1900-1800 Ma ago (Palaeoproterozoic). The sandstone area is the remnant of an alluvial basin, preserved now in a NW-SE trending graben, bounded on both sides by normal fault zones. The sandstones are thought to be at least 1400-1300 Ma old (Mesoproterozoic), and they are cut by Postjotnian olivine diabase dykes, 1270-1250 Ma in age. The Svecofennian migmatite belts show a complex history of formation, with various phases of anatexis/metamorphism, deformation and intrusion. In the pelitic migmatite belt, in which the Olkiluoto site is situated, four phases of ductile deformation (D-D4) and two phases of regional highT/lowP metamorphism and migmatite formation can be recognised, together with synorogenic (tonalite, granodiotite) and late orogenic ( potassium granite) intrusions. Subsequently, this very heterogeneous complex was intruded by anorogenic rapakivi granites, with ages 1580-1550 Ma. One pluton, the Eurajoki stock

  2. Seismic VSP and crosshole investigations in Olkiluoto, 2002

    International Nuclear Information System (INIS)

    Enescu, N.; Cosma, C.; Balu, L.

    2003-04-01

    Vertical Seismic Profiling (VSP) and crosshole seismic surveys were conducted during 2002 at Olkiluoto site in Eurajoki, Finland. The VSP investigations were carried out in three boreholes (KR13, KR14 and KR19) with ten or eleven shot points for each borehole. Additionally, the data from a VSP investigation carried out in 1990 in borehole KR5 had been reprocessed with state of the art tools. One crosshole section (KR14-KR15 at 20 - 240 m interval) was measured and processed. Different receiver types were used for the VSP and crosshole: a 3-component geophone chain for VSP and a hydrophone chain for crosshole. VSP surveys have been carried out with a VIBSIST-1000 source - a time-distributed swept-impact source - instead of explosives. With this source, the seismic signals are produced as rapid series of impacts, the impact intervals being monotonically increased to achieve a nonrepeatable sequence. The VIBSIST-1000 uses a tractor-mounted hydraulic rock-breaker, powered through a computer controlled servo-hydraulic flow regulator. Using standard construction equipment ensures that the VIBSIST sources are safe, non-destructive and environmentally friendly. This also makes the method reliable and cost effective. The new VIBSIST source produces signals with levels of energy comparable to explosives. The VIBSIST appears to be more stable, but its most significant advantages are the low cost of preparation of the shot points and the speed of the acquisition. Crosshole surveys were carried out with a piezoelectric borehole source, the VIBSISTSPH54, which operates on the same principle as the surface VIBSIST source. The wide diversity of reflection angles, the local variations of reflectivity and, generally, the relatively weak seismic response of faults and fractured zones in crystalline rock demand intensive processing. The first stage of the processing sequence focuses on eliminating such wave-fields as the direct P, direct S, tube-waves and ground-roll, so that the

  3. Seismic VSP and crosshole investigations in Olkiluoto, 2002

    Energy Technology Data Exchange (ETDEWEB)

    Enescu, N.; Cosma, C.; Balu, L. [Vibrometric Oy (Finland)

    2003-04-01

    Vertical Seismic Profiling (VSP) and crosshole seismic surveys were conducted during 2002 at Olkiluoto site in Eurajoki, Finland. The VSP investigations were carried out in three boreholes (KR13, KR14 and KR19) with ten or eleven shot points for each borehole. Additionally, the data from a VSP investigation carried out in 1990 in borehole KR5 had been reprocessed with state of the art tools. One crosshole section (KR14-KR15 at 20 - 240 m interval) was measured and processed. Different receiver types were used for the VSP and crosshole: a 3-component geophone chain for VSP and a hydrophone chain for crosshole. VSP surveys have been carried out with a VIBSIST-1000 source - a time-distributed swept-impact source - instead of explosives. With this source, the seismic signals are produced as rapid series of impacts, the impact intervals being monotonically increased to achieve a nonrepeatable sequence. The VIBSIST-1000 uses a tractor-mounted hydraulic rock-breaker, powered through a computer controlled servo-hydraulic flow regulator. Using standard construction equipment ensures that the VIBSIST sources are safe, non-destructive and environmentally friendly. This also makes the method reliable and cost effective. The new VIBSIST source produces signals with levels of energy comparable to explosives. The VIBSIST appears to be more stable, but its most significant advantages are the low cost of preparation of the shot points and the speed of the acquisition. Crosshole surveys were carried out with a piezoelectric borehole source, the VIBSISTSPH54, which operates on the same principle as the surface VIBSIST source. The wide diversity of reflection angles, the local variations of reflectivity and, generally, the relatively weak seismic response of faults and fractured zones in crystalline rock demand intensive processing. The first stage of the processing sequence focuses on eliminating such wave-fields as the direct P, direct S, tube-waves and ground-roll, so that the

  4. Long-term development of the super-regional area of Olkiluoto/Forsmark/Laxemar. Minutes from the Posiva and SKB workshop

    Energy Technology Data Exchange (ETDEWEB)

    Lindborg, Tobias; Rubio Lind, Lotta (eds.)

    2006-12-15

    minutes were delimited in the description of the surface system part of the geosphere-biosphere system and its development in time, primarily in terms of geometry and sea water salinity. However, no effort was made to discuss the geological evolution of the area or any parameter in the bedrock separately. Instead, the focus was to list, describe and suggest the parameters and variables of the surface system that can be described in a common way for the three sites Olkiluoto (Finland), Forsmark and Laxemar (both in Sweden)

  5. Long-term development of the super-regional area of Olkiluoto/Forsmark/Laxemar. Minutes from the Posiva and SKB workshop

    International Nuclear Information System (INIS)

    Lindborg, Tobias; Rubio Lind, Lotta

    2006-12-01

    minutes were delimited in the description of the surface system part of the geosphere-biosphere system and its development in time, primarily in terms of geometry and sea water salinity. However, no effort was made to discuss the geological evolution of the area or any parameter in the bedrock separately. Instead, the focus was to list, describe and suggest the parameters and variables of the surface system that can be described in a common way for the three sites Olkiluoto (Finland), Forsmark and Laxemar (both in Sweden)

  6. Results of monitoring at Olkiluoto in 2008. Environment

    International Nuclear Information System (INIS)

    Haapanen, A.

    2009-09-01

    This Working Report presents the main results of Posiva Oy's environmental monitoring programme on Olkiluoto Island in 2008. These summary reports have been published since 2005 (target year 2004). The environmental monitoring system supervised by Posiva Oy produces input for biosphere modelling for long-term safety purposes as well as for monitoring the state of the environment during the construction (and later operation) of ONKALO underground characterization facility. Although some of the nuclear power production related monitoring studies by TVO (the power company) have been going on from the 1970s, the repository-related environmental monitoring of Olkiluoto Island has only recently been comprehensive. However, the monitoring programme evolves according to experiences from modelling work and increasing knowledge of most important site data. For example, in addition to the originally planned activities, in 2008 several studies on fauna were carried out, some soil and vegetation transects running from land to sea were established, a separate survey of water quality with automatic detectors was carried out and zooplankton and organic carbon studies were started in context of sea monitoring. In the monitoring data, the ongoing construction work (OL3, ONKALO and related infrastructure) is seen for instance in raised levels of noise and some deposited elements. The land-use continues to change, but where there is natural environment is affected by the cooling water from the nuclear power plant. (orig.)

  7. Threats and benefits updated information on local opinions regarding the spent nuclear fuel repository in Finland - 16128

    International Nuclear Information System (INIS)

    Kojo, Matti; Kari, Mika; Litmanen, Tapio

    2009-01-01

    The aim of the paper is to provide updated information on local opinion regarding the siting of a spent nuclear fuel repository in Finland. The main question is how the residents of the municipality perceive the threats and benefits of the repository. In accordance with the Decision in Principle by the Council of State passed in 2000, the Olkiluoto area in Municipality of Eurajoki was chosen as the location for the repository to accommodate spent nuclear fuel produced in Finland. Updated information on local opinions is needed as the siting process is approaching the next phase, the application for a construction license by 2012. The nuclear waste management company Posiva, owned by the utilities Teollisuuden Voima and Fortum Power and Heat, has also applied for a new Decision in Principle (DiP) for expansion of the repository. The data provided in this paper is based on a survey carried out in June 2008. The respondents were selected from the residents of the municipality of Eurajoki and the neighbouring municipalities using stratified random sampling (N=3000). The response rate of the survey was 20% (N=606). The paper is part of a joint research project between the University of Jyvaeskylae and the University of Tampere. The research project 'Follow-up research regarding socio-economic effects and communication of final disposal facility of spent nuclear fuel in Eurajoki and its neighbouring municipalities' is funded by the Finnish Research Programme on Nuclear Waste Management (KYT2010). (authors)

  8. Enhancing the economic competitiveness of the Olkiluoto Nuclear Power Plants

    International Nuclear Information System (INIS)

    Paavola, M.

    1996-01-01

    The two 710 MWe BWRs at Olkiluoto in Finland have been running for the past ten years with a capacity factor of over 90%. The success of these reactors in being competitive with various forms of fossil fuel power production is attributed to a number of key factors. Of these, the most important is that the staff of the utility and contractors and suppliers personnel are well trained, committed and able to learn new things. Strict safety regulations contribute to competitiveness because the good practice required and the need to keep the plant in mint condition lead to fewer production interruptions and to lower operational costs in the long run. Continuous investment in updating the plant is necessary to maintain high productivity throughout its lifetime. A long-term operational plan coupled with carefully prepared maintenance outages and high quality workmanship also helps to ensure good performance. Better fuel designs and high quality have enabled the plant output to be increased while stabilising or reducing fuel costs. Money for waste management has been reserved since the start of plant operation so that economic production can be ensured during the latter part of the plant lifetime. (UK)

  9. Deformations during saturation of the crushed aggregate, Olkiluoto tonalite

    International Nuclear Information System (INIS)

    Laaksonen, R.; Rathmayer, H.; Takala, J.; Toernqvist, J.

    1994-03-01

    Crushed aggregate tonalite produced of crystalline tonalite or a correspondent rock with particle size up to 8 mm (or 16 mm) will be used as backfill material in the VLJ repository caverns at Olkiluoto (in Finland). The backfill material has to retard radionuclides, to restrict the groundwater perlocation and to support mechanically the concrete structure of the repository silos. Mechanical and hydraulic behaviour of crushed tonalite when effected by stresses applied during compaction of the backfill and due to groundwater perlocation was studied at three batches having different gradations. Information about the phenomenon of settlement due to saturation and as a function of the compaction methods was obtained from a literature survey. The maximum amount of possible deformation due to compaction was analyzed with a gyratory device, known to have a good repeatability. In a group of simulation tests using a large oedometer cell the amount of compression due to the saturation process was measured. Also studies on the suitability of different compaction methods could be done with these tests. (43 refs., 49 figs., 3 tabs.)

  10. Electromagnetic SAMPO monitoring soundings at Olkiluoto 2011 with updated interpretations

    International Nuclear Information System (INIS)

    Korhonen, K.

    2013-11-01

    The Geological Survey of Finland (GTK) has carried out electromagnetic depth soundings annually at fixed stations in Olkiluoto since 2004 as part of a monitoring programme. The goal of the programme is to detect and monitor changes in the electrical properties of the bedrock above and in the vicinity of the underground nuclear waste disposal facility. A new Sampo monitoring survey was carried out during September-October 2011. The survey resulted in 39 soundings at 17 measurement stations. The nominal coil separations of 200, 400, 500, 600 and 800 meters were used. Eight stations were selected for detailed annual layer-model interpretation. The layer models were based on prior geological and geophysical knowledge of the area. The thicknesses of the layer-model layers were kept fixed whereas their resistivities were solved for each subsequent year independent of each other. Many time series indicate clear trends in electrical resistivity. However, even though the data was carefully corrected and edited, the time series display a fairly large amount of variability increasing the uncertainty of the calculated trends. (orig.)

  11. Interpretation of electromagnetic Sampo monitoring soundings of Olkiluoto

    International Nuclear Information System (INIS)

    Korhonen, K.

    2010-04-01

    The Geological Survey of Finland (GTK) has carried out electromagnetic Sampo soundings at Olkiluoto annually since 2004 commissioned by Posiva. The soundings have been carried out at the same measurement stations every year. The goal of the soundings is to detect any changes in the electrical conditions of the bedrock surrounding the ONKALO underground research facility. This study aims to detect possible changes in the groundwater conditions using modelling. The sensitivity of the Sampo method to changes in the electrical properties and the level of groundwater were investigated as part of this study. The results of the sensitivity investigation indicate that the Sampo method is capable of detecting changes occurring even quite deep in the bedrock. Thus, the usage of the Sampo method to monitor the groundwater conditions is warranted. The plots of apparent resistivity as a function of depth indicate that the area directly above the ONKALO facility is very disturbed electromagnetically. However, most of the soundings to the east and west of ONKALO are of better quality and were interpreted. The results indicate possible changes in the groundwater conditions. The level of saline groundwater may be sinking in the eastern part while it may be rising on the western part. (orig.)

  12. The introduction of nuclear power in Finland

    International Nuclear Information System (INIS)

    Jaafs, Daniel

    2009-01-01

    The aim of my research was to study the introduction of nuclear power in Finland with special focus on the domestic engineering works industry. I wanted to find out what really happened during this long process, which I consider to be unique. I also tried to clearfy the reasons why it came about at all, and why it developed in such a peculiar way. My basic research questions were: (a.) When and how was nuclear power introduced in Finland? (b.) Which were the reasons for this introduction and which were the results? (c.) Which was the role of the domestic engineering works industry? I started the investigation by exploring the original situation in Finland and also in the countries which came to be a primus motor for the development. I studied the relevant literature and interviewed quite a few of the persons who in a decisive way had an influence on the long and chaotic process which led to the introduction of nuclear power in Finland. When describing the different phases in the development I stayed in principle within the historic framework, although I diverged from a strict chronological order when necessary. Neither did I in my investigation take a neutral stance regarding the two large projects that had a central position in the introduction, namely the nuclear power plants in Lovisa and in Olkiluoto. The Lovisa project implied a greater challenge and it was also more important to the domestic industry than Olkiluoto. It therefore got more attention than Olkiluoto. Oy Finnatom Ab (managed by me 1975-2001), due to its role as a spokesman for the Finnish nuclear engineering works industry, occupied a central position in my investigation. The start of the introduction may psychologically be dated to the startup in 1958 of the Ydin Exponential pile, YXP, and in 1962 of Finland Reactor I, FiR I, and the end to the signing in 1982 by Industrins Kraft, ASEA and Asea-Atom of the acceptance protocol for Olkiluoto and the final permits for Lovisa, granted by the

  13. Indicator value of certain aquatic organisms for radioactive substances in the sea areas off the Loviisa and Ilkiluoto nuclear power plants (Finland)[Radioecology

    Energy Technology Data Exchange (ETDEWEB)

    Ilus, E.; Klemola, S.; Ikaeheimonen, T.K.; Vartti, V.P.; Mattila, J. [STUK - radiation and Nuclear Safety Authority, Helsinki (Finland)

    2006-04-15

    The results of the marine radioecology studies carried out in 2000-2001 in the sea areas off the Loviisa and Olkiluoto Nuclear Power Plants (South and West coast of Finland) are reported. Extensive regular monitoring programmes of environmental radioactivity have been carried out already for about 30 years in these areas. The aim of the present study was to compare the indicator value of the various members of the aquatic ecosystem with respect to environmental monitoring. Samples were taken from 27 species including phytoplankton (9 samples), zooplankton (9 samples), periphyton (12 samples), macroalgae and vascular plants (16 samples), benthic animals (8 samples), fish (20 samples) and birds (6). Special attention was paid to different tissues and organs of fish and birds, such as flesh, liver, entrails, bones, milt, spawn, eggs, egg shells etc. (in total 64 samples), because there has been a lot of debate among the opponents of nuclear power in the course of time about the role these objects in the environmental monitoring of the power plants. The samples were taken from relatively small areas both in Loviisa and Olkiluoto, which makes the results well comparable inside each of the sites. (au)

  14. Mass-balance modelling results of groundwater data collected at Olkiluoto over the period 2004-2007

    Energy Technology Data Exchange (ETDEWEB)

    Partamies, S. [VTT Technical Research Centre of Finland, Espoo (Finland); Pitkaenen, P.

    2014-02-15

    Olkiluoto has been selected as a repository site for final disposal of spent nuclear waste produced in Finland. An understanding of the hydrogeochemical groundwater conditions and their evolution is essential in evaluating the long-term safety of the repository. The performance of technical barriers and the migration of potentially released radionuclides depend on the chemical conditions. A prerequisite for understanding these factors is the ability to specify the water-rock interactions, which control chemical conditions in the groundwater. The objective of this study is to present mass-balance studies of the samples collected over the period 2004 - 2007. A total of 178 groundwater samples have been collected over this period (84 groundwater observation tubes, 88 from deep multipackered boreholes and 6 from the ONKALO) which provided a comprehensive dataset on dissolved chemical species and isotopes. The PHREEQC program was used in the mass-balance calculations in order to develop geochemical interpretations of water-rock interactions, isotope-chemical evolution and the mixing of palaeowater types. A model of the hydrogeochemical evolution in different parts of the crystalline bedrock at Olkiluoto has been created and the significance of chemical reactions and groundwater mixing along different flow paths calculated. The changes in hydrogeochemical interpretations and chemical and isotopic calculations indicate that pH seems to be dominantly controlled by thermodynamic equilibrium with calcite in fractures and there are indications that this process may also occur in the overburden layer. Oxic redox conditions, prevailing in recharging groundwater, change abruptly to sulphidic conditions close to the surface, generally in the overburden. The results from the mass-balance calculations correspond and support the earlier conceptions of groundwater mixing, the origin of salinity and the hydrogeochemical evolution. The fractions of glacial meltwater indicated in these

  15. Mass-balance modelling results of groundwater data collected at Olkiluoto over the period 2004-2007

    International Nuclear Information System (INIS)

    Partamies, S.; Pitkaenen, P.

    2014-02-01

    Olkiluoto has been selected as a repository site for final disposal of spent nuclear waste produced in Finland. An understanding of the hydrogeochemical groundwater conditions and their evolution is essential in evaluating the long-term safety of the repository. The performance of technical barriers and the migration of potentially released radionuclides depend on the chemical conditions. A prerequisite for understanding these factors is the ability to specify the water-rock interactions, which control chemical conditions in the groundwater. The objective of this study is to present mass-balance studies of the samples collected over the period 2004 - 2007. A total of 178 groundwater samples have been collected over this period (84 groundwater observation tubes, 88 from deep multipackered boreholes and 6 from the ONKALO) which provided a comprehensive dataset on dissolved chemical species and isotopes. The PHREEQC program was used in the mass-balance calculations in order to develop geochemical interpretations of water-rock interactions, isotope-chemical evolution and the mixing of palaeowater types. A model of the hydrogeochemical evolution in different parts of the crystalline bedrock at Olkiluoto has been created and the significance of chemical reactions and groundwater mixing along different flow paths calculated. The changes in hydrogeochemical interpretations and chemical and isotopic calculations indicate that pH seems to be dominantly controlled by thermodynamic equilibrium with calcite in fractures and there are indications that this process may also occur in the overburden layer. Oxic redox conditions, prevailing in recharging groundwater, change abruptly to sulphidic conditions close to the surface, generally in the overburden. The results from the mass-balance calculations correspond and support the earlier conceptions of groundwater mixing, the origin of salinity and the hydrogeochemical evolution. The fractions of glacial meltwater indicated in these

  16. Strategies for safe and cost-efficient management of nuclear wastes in Finland

    International Nuclear Information System (INIS)

    Ryhanen, V.

    2002-01-01

    Full text: In 2001, the Finnish Parliament ratified the Decision-in-Principle on a final disposal facility of spent fuel to be constructed at the Olkiluoto site in the Western Finland. Since the early 1980s, this decision was grounded up by R and D and siting activities as well as by communications aiming at confidence building. Before the recent important licensing and siting step in the national waste management programme, interim storage facilities for spent fuel have been constructed at both nuclear power plant sites. Two shallow underground repositories were commissioned for low- and medium-level operating waste in the 1990s. Long-term programme and stepwise advancement have facilitated keeping the annual costs of nuclear waste management moderate. All major objectives were decided by the Government already in an early phase several decades ago, and these objectives have been met without significant delays. Nuclear power plant areas have been found out to be suitable even for location of waste storage and disposal facilities, which means benefits concerning infrastructure. Funds for R and D and implementation of waste management have been collected in the price of nuclear electricity since the start of nuclear power generation. (author)

  17. Results of monitoring at Olkiluoto in 2012. Rock mechanics

    International Nuclear Information System (INIS)

    Johansson, E.; Siren, T.

    2014-01-01

    datalogger. The results showed that the displacement behaviour was stable during 2012 and no significant changes took place. For the first time temperature measurements were collected from different sources of the Olkiluoto site (surface, drillholes and underground in the ONKALO). All the results were analysed and they indicate relatively uniform distributions of temperature in all depths across the site. Thermal gradient is around 1.4 deg C/100 m below 300 m. Visual observations from the ONKALO tunnels were also collected and analysed. The rock noises i.e. first indication of possible rock damage have been only recorded after the depth of 250 m and often related to the tunnel crossings or intersections. Rock fallouts have been observed at all depths (150 - 450 m) and they seem to be affected more by the weaknesses in the rock structure (foliation, fracturing, rock type contacts) than the tunnel orientation. (orig.)

  18. The analysis of the bedrock deformation in Olkiluoto using precise levelling measurements

    International Nuclear Information System (INIS)

    Saaranen, V.; Rouhiainen, P.; Suurmaeki, H.

    2014-01-01

    In order to research vertical bedrock deformations in the Olkiluoto area, Posiva Oy and the Finnish Geodetic Institute began monitoring with precise levelling in 2003. At the moment, the measuring plan includes a loop between the monitoring GPS stations around the island, a levelling line from the island to the mainland, levelling loops to ONKALO, the final disposal site, and VLJ, the low and intermediate level waste repository there. The levelling to the mainland has been performed every fourth year and the levelling of the GPS stations every second year. The micro loops (ONKALO and VLJ) have been measured annually. In this report, we use three-step method to research a vertical deformation of the Olkiluoto area. Firstly, the linear deformation rate in the area has been determined by the least squares adjustment of the levelling data. It varies from -0.2 mm/yr to +0.2 mm/yr. Secondly, local deformations have been analysed by comparing the height differences for different years. In this comparison a starting value for the yearly adjustment has been corrected for land uplift. Using this method the elevation changes are relative to the whole network. For a fixed benchmark, we correct its yearly deformation. Thirdly, the fault lines have been analysed by comparing the elevation changes between the successive benchmarks from one observation epoch to another. The results show that ONKALO and Lapijoki are in the subsidence area of the network, and VLJ has small uplift rate. On the island some deformations exist, but elevation difference from 2003 to 2011 is less than one millimetre at every benchmarks. The measurements in the Lapijoki-Olkiluoto line in 2003, 2007 and 2011 show that linear elevation change between the mainland and Olkiluoto island is a little since 2003. The elevation differences, from Olkiluoto to Lapijoki, measured in 2003 and 2011 differ less than one millimetre each other, but the 2007 observation differs three millimetres from the other measurements

  19. Same, same but different. A comparative perspective on participation and acceptance in siting procedures for HLW repositories in France, Sweden and Finland

    Energy Technology Data Exchange (ETDEWEB)

    Di Nucci, Maria Rosaria; Isidoro Losada, Ana Maria; Brunnengraeber, Achim [Freie Univ. Berlin (Germany). Environmental Policy Research Centre

    2015-07-01

    This paper compares national approaches in Finland, Sweden, and France. These three EURATOM Member States are in an advanced stage of siting deep geological disposal (DGD) facilities. The procedures in these countries are largely based on voluntarism, but differ in their approach to public consultation as they were based on the so-called staged volunteer process leading to working partnership arrangements between the operator and the hosting communities and veto rights (Sweden), decisions with strong local community support and veto rights for municipalities until the final decision (Finland), and final top-down decision making after consultative processes (debat public) with the affected communities without veto rights (France). This presentation focuses on participation and acceptance issues; it analyses the different modes of governance with diverse conditions regarding transparency, trust, communication, and participation that have been at work. Moving beyond the fact that variance exists with regard to the relevant national institutional, legal, cultural, industrial, and energy frameworks, the authors take evidence from national case studies and look for common patterns.

  20. Same, same but different. A comparative perspective on participation and acceptance in siting procedures for HLW repositories in France, Sweden and Finland

    International Nuclear Information System (INIS)

    Di Nucci, Maria Rosaria; Isidoro Losada, Ana Maria; Brunnengraeber, Achim

    2015-01-01

    This paper compares national approaches in Finland, Sweden, and France. These three EURATOM Member States are in an advanced stage of siting deep geological disposal (DGD) facilities. The procedures in these countries are largely based on voluntarism, but differ in their approach to public consultation as they were based on the so-called staged volunteer process leading to working partnership arrangements between the operator and the hosting communities and veto rights (Sweden), decisions with strong local community support and veto rights for municipalities until the final decision (Finland), and final top-down decision making after consultative processes (debat public) with the affected communities without veto rights (France). This presentation focuses on participation and acceptance issues; it analyses the different modes of governance with diverse conditions regarding transparency, trust, communication, and participation that have been at work. Moving beyond the fact that variance exists with regard to the relevant national institutional, legal, cultural, industrial, and energy frameworks, the authors take evidence from national case studies and look for common patterns.

  1. Plan for safety case of spent fuel repository at Olkiluoto

    International Nuclear Information System (INIS)

    Vieno, T.; Ikonen, A.T.K.

    2005-02-01

    Posiva aims to present the Safety Case supporting the construction license application of the spent fuel repository at Olkiluoto by 2012. An outline and preliminary assessments will be presented in 2009. Interim reporting and an update of the Safety Case plan will be presented in 2006, as required by the authorities. The KBS-3 disposal concept aims at long-term isolation and containment of spent fuel assemblies in durable copper-iron canisters emplaced in a repository to be constructed at a depth between 400 and 600 metres in crystalline bedrock. By 2012, studies on the KBS-3 disposal concept and site investigations at Olkiluoto will have been continued over about thirty years. The construction of an underground rock characterisation facility (called ONKALO) was started in June 2004. The investigations are carried out in close cooperation with the Swedish SKB developing and assessing the same disposal concept at candidate sites, resembling Olkiluoto, at the other side of the Baltic Sea. A safety case is the synthesis of evidence, analyses and arguments that quantify and substantiate the safety, and the level of expert confidence in the safety, of a planned repository. Posiva's Safety Case will be organised in a portfolio including ten main reports, which will be periodically updated according the overall schedule presented in the plan. The Site report describing the present state and past evolution of the Olkiluoto site, as well as the disturbances caused by the construction of ONKALO and the first stage of the repository, forms the geoscientific basis of the Safety Case. The engineering basis is provided by the reports on the Characteristics of spent fuel, Canister design, and Repository design. The Process report containing descriptions and analyses of features, events and processes potentially affecting the disposal system, and the report on the Evolution of site and repository form the scientific basis of the Safety Case. The latter report will describe and

  2. Microbiology of Olkiluoto groundwater. Results and interpretations 2007

    International Nuclear Information System (INIS)

    Pedersen, K.; Arlinger, J.; Eriksson, S.; Hallbeck, M.; Johansson, J.; Jaegevall, S.; Karlsson, L.

    2008-09-01

    Research in 2007 continued the general program of analysing microorganisms and gas in deep groundwater. New tasks examined the presence of anaerobic methane oxidation, the growth of slime on the tunnel walls of ONKALO, and the possible presence of microorganisms that produce complexing agents in groundwater and the slime. Microbiology, chemistry, and dissolved gas data were assembled in 2007 from three deep drillholes in Olkiluoto, Finland, ranging in depth from 39.5 to 294.0 m and in 2005-2007 from six drillholes in ONKALO ranging in depth from 7.1 to 78.5 m. In addition, 24 analyses of gas from nine deep drillholes ranging in depth from 16 to 490 m and one analysis of gas from an ONKALO drillhole of a depth of 14.6 m were executed. The microbiology of shallow and deep groundwater from Olkiluoto had previously been analysed for almost three years from 2004 to 2006. Microbiological and geochemical data strongly suggested that the anaerobic microbial oxidation of methane (ANME) is active at a depth of approximately 300 m in Olkiluoto. However, proof of the presence and activity of ANME microorganisms was deemed necessary before the existence of active ANME processes in Olkiluoto groundwater could be accepted. Part of the research on behalf of Posiva Oy in 2007 therefore was focused on the development and testing of methods for detecting ANME microorganisms. The groundwater from the ONKALO tunnel was also analysed, and slimy biofilms were found growing on the rock walls at some positions in ONKALO late 2006. It was assumed that the ONKALO slime microbes were growing on various substances added to the shotcrete, the injected concrete, or both. Part of the 2007 research focused on detailed analysis of the slime microorganisms and their potential for acid production. The presence of microorganisms that produce complexing agents, for example, siderophores such as pyoverdin and ferrioxamine, was indicated in 2006 in the ONKALO slime as judged from DNA diversity data. It

  3. Modelling of groundwater flow and solute transport in Olkiluoto. Update 2008

    International Nuclear Information System (INIS)

    Loefman, J.; Pitkaenen, P.; Meszaros, F.; Keto, V.; Ahokas, H.

    2009-10-01

    Posiva Oy is preparing for the final disposal of spent nuclear fuel in the crystalline bedrock in Finland. Olkiluoto in Eurajoki has been selected as the primary site for the repository, subject to further detailed characterisation which is currently focused on the construction of an underground rock characterisation and research facility (the ONKALO). An essential part of the site investigation programme is analysis of the deep groundwater flow by means of numerical flow modelling. This study is the latest update concerning the site-scale flow modelling and is based on all the hydrogeological data gathered from field investigations by the end of 2007. The work is divided into two separate modelling tasks: 1) characterization of the baseline groundwater flow conditions before excavation of the ONKALO, and 2) a prediction/outcome (P/O) study of the potential hydrogeological disturbances due to the ONKALO. The flow model was calibrated by using all the available data that was appropriate for the applied, deterministic, equivalent porous medium (EPM) / dual-porosity (DP) approach. In the baseline modelling, calibration of the flow model focused on improving the agreement between the calculated results and the undisturbed observations. The calibration resulted in a satisfactory agreement with the measured pumping test responses, a very good overall agreement with the observed pressures in the deep drill holes and a fairly good agreement with the observed salinity. Some discrepancies still remained in a few single drill hole sections, because the fresh water infiltration in the model tends to dilute the groundwater too much at shallow depths. In the P/O calculations the flow model was further calibrated by using the monitoring data on the ONKALO disturbances. Having significantly more information on the inflows to the tunnel (compared with the previous study) allowed better calibration of the model, which allowed it to capture very well the observed inflow, the

  4. Safety case for the disposal of spent nuclear fuel at Olkiluoto. Formulation of radionuclide release scenarios 2012

    International Nuclear Information System (INIS)

    2013-04-01

    TURVA-2012 is Posiva's safety case in support of the Preliminary Safety Analysis Report (PSAR) and application for a construction licence for a repository for disposal of spent nuclear fuel at the Olkiluoto site in south-western Finland. This report presents the radionuclide release scenarios and the methodology followed in formulating them. The formulation of scenarios takes into account the regulatory framework, the knowledge acquired in the present safety case as well as in previous safety assessments, the safety functions of the barriers of the repository system and the uncertainties in the features, events, and processes (FEPs) that may affect the entire disposal system (i.e. repository system plus the surface environment) from the emplacement of the first canister until the far future. In the report Performance Assessment, the performance of the engineered and natural barriers has been assessed against the loads expected during the evolution of the repository system and the site. Uncertainties have been identified and these are taken into account in the formulation of radionuclide release scenarios. The uncertainties in the FEPs affecting the characteristics and evolution of the surface environment are taken into account in formulating the surface environment scenarios used ultimately for assessing radiation exposure. Formulating radionuclide release scenarios for the repository system links the reports Performance Assessment and Assessment of Radionuclide Release Scenarios for the Repository System. The formulation of radionuclide release scenarios for the surface environment brings together Biosphere Description and the surface environment FEPs and is the link to the assessment of the surface environment scenarios analysed in Biosphere Assessment. (orig.)

  5. The use of gamma spectrometry in mapping alteration zones in Olkiluoto

    International Nuclear Information System (INIS)

    Ojala, J.V.; Turunen, P.; Eilu, P.; Julkunen, A.; Gehoer, S.

    2007-08-01

    In the Olkiluoto site, a detailed gammaspectrometry log from the drill hole OL-KR27 was used to estimate the concentrations of K, Th and U. The gamma spectrometry results, lithological variations, and kaolinite and illite alteration visually mapped from the drill hole were compared. The result indicate that the Th/K ratio correlates best with lithology and that, in most cases, the changes in the ratio indicate lithological contacts and rising or falling trends of Th/K ratio with some peaks have some correlation with the kaolinite-illite alteration. From the result it is suggested that that very variable Th/K ratio is a reasonably good indicator of alteration zones even in the migmatic gneiss area in the Olkiluoto site. (orig.)

  6. Studies on the aquatic environment at Olkiluoto and reference area. 1: Olkiluoto, reference lakes and Eurajoki and Lapijoki rivers in 2009-2010

    Energy Technology Data Exchange (ETDEWEB)

    Kangasniemi, V. [Environmental Research and Assessment EnviroCase Ltd., Pori (Finland); Helin, J.

    2014-03-15

    This working report presents the first results of a sampling campaign at Olkiluoto and reference lakes and rivers selected to resemble the aquatic systems expected to form at the site in the future with the post-glacial crustal rebound (land uplift). In 2009-2010, the aim of the studies was to improve the knowledge of the aquatic systems and to produce input data to the safety case for the spent nuclear fuel repository at Olkiluoto. The first main objective was to estimate the areal biomass distribution and measure the dimensions of characteristic aquatic plants and animals. Another objective was to estimate the transfer of different elements from water to the aquatic organisms paying special attention on key elements (Ag, Cl, I, Mo, Nb and Se) in the dose assessment within the safety case. Surface water, sediment, macrophyte, fish and macrobenthos samples were collected from the Olkiluoto coastal area and from the reference lakes for biomass and dimension measurements and analysis of element concentration. Water-to-biota concentration ratios were estimated for the coastal area and for the reference lakes. From rivers, only water samples were collected at this stage. In 2009-2010, sampling procedures and pre-treatment methods were developed and analytical methods were optimised. Thus, the results reported here are indicative by their nature. After 2010, the studies have been continued with better established methods, and the more recent results will be reported later. (orig.)

  7. Licensing process in Finland

    International Nuclear Information System (INIS)

    Tiippana, Petteri

    2011-01-01

    In accordance with the Nuclear Energy Act, the use of nuclear energy constitutes operations subject to license. The licensing process and conditions for granting a license is defined in the legislation. The licenses are applied from and granted by the Government. This paper discusses briefly the licensing process in Finland and also the roles and responsibilities of main stakeholders in licensing. Licensing of a nuclear power plant in Finland has three steps. The first step is the Decision in Principle (DiP). Goal of DiP is to decide whether using nuclear power is for the overall good for the Finnish society. The second step is Construction License (CL) and the goal of CL phase is to determine whether the design of the proposed plant is safe and that the participating organisations are capable of constructing the plant to meet safety goals. The third step is the Operating License (OL) and the goal of the OL phase is to determine whether the plant operates safely and licensee is capable to operate the plant safely. Main stakeholders in the licensing process in Finland are the utility (licensee) interested in using nuclear power in Finland, Ministry of Employment and the Economy (MEE), Government, Parliament, STUK, the municipality siting the plant and the general public. Government grants all licenses, and Parliament has to ratify Government's Decision in Principle. STUK has to assess the safety of the license applications in each step and give statement to the Ministry. Municipality has to agree to site the plant. Both STUK and the municipality have a veto right in the licensing process

  8. Mise-a-la-Masse Measurements at Olkiluoto in 2010

    International Nuclear Information System (INIS)

    Tarvainen, A.-M.

    2010-10-01

    Suomen Malmi Oy carried out Mise-a-la-Masse measurements at Olkiluoto site in Eurajoki during March-June 2010. The survey consisted of measurements in 9 drillholes and on 76 surface profiles. The measured drillholes were OL-KR11, OL-KR40, OLKR44, OL-KR45 and OL-KR49..OL-KR53. Surface measurements were carried out at 4 different areas. Current electrodes were placed in drillholes OL-KR49 - OL-KR53. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work. This report describes the field operation, the equipment and shows the obtained results and their quality. The raw and processed data are delivered digitally in Microsoft Ecxel format. (orig.)

  9. Temperature Dependency of the Correlation between Secondary Organic Aerosol and Monoterpenes Concentrations at a Boreal Forest Site in Finland

    Science.gov (United States)

    Zhou, Y.; Zhang, W.; Rinne, J.

    2016-12-01

    Climate feedbacks represent the large uncertainty in the climate projection partly due to the difficulties to quantify the feedback mechanisms in the biosphere-atmosphere interaction. Recently, a negative climate feedback mechanism whereby higher temperatures and CO2-levels boost continental biomass production, leading to increased biogenic secondary organic aerosol (SOA) and cloud condensation nuclei concentrations, tending to cause cooling, has been attached much attention. To quantify the relationship between biogenic organic compounds (BVOCs) and SOA, a five-year data set (2008, 2010-2011,2013-2014) for SOA and monoterpenes concentrations (the dominant fraction of BVOCs) measured at the SMEAR II station in Hyytiälä, Finland, is analyzed. Our results show that there is a moderate linear correlation between SOA and monoterpenes concentration with the correlation coefficient (R) as 0.66. To rule out the influence of anthropogenic aerosols, the dataset is further filtered by selecting the data at the wind direction of cleaner air mass, leading to an improved R as 0.68. As temperature is a critical factor for vegetation growth, BVOC emissions, and condensation rate, the correlation between SOA and monoterpenes concentration at different temperature windows are studied. The result shows a higher R and slope of linear regression as temperature increases. To identify the dominant oxidant responsible for the BVOC-SOA conversion, the correlations between SOA concentration and the monoterpenes oxidation rates by O3 and OH are compared, suggesting more SOA is contributed by O3 oxidation process. Finally, the possible processes and factors such as the atmospheric boundary layer depth, limiting factor in the monoterpenes oxidation process, as well as temperature sensitivity in the condensation process contributing to the temperature dependence of correlation between BVOA and SOA are investigated.

  10. Safety case for the disposal of spent nuclear fuel at Olkiluoto - Synthesis 2012

    International Nuclear Information System (INIS)

    2012-12-01

    TURVA-2012 is Posiva's safety case in support of the Preliminary Safety Analysis Report (PSAR 2012) and application for a construction licence for a spent nuclear fuel repository. Consistent with the Government Decisions-in- Principle, this foresees a repository developed in bedrock at the Olkiluoto site according to the KBS-3 method, designed to accept spent nuclear fuel from the lifetime operations of the Olkiluoto and Loviisa reactors. Synthesis 2012 presents a synthesis of Posiva Oy's Safety Case 'TURVA-2012' portfolio. It summarises the design basis for the repository at the Olkiluoto site, the assessment methodology and key results of performance and safety assessments. It brings together all the lines of argument for safety, evaluation of compliance with the regulatory requirements, and statement of confidence in long-term safety and Posiva's safety analyses. The TURVA-2012 safety case demonstrates that the proposed repository design provides a safe solution for the disposal of spent nuclear fuel, and that the performance and safety assessments are fully consistent with all the legal and regulatory requirements related to long-term safety as set out in Government Decree 736/2008 and in guidance from the nuclear regulator - the STUK. Moreover, Posiva considers that the level of confidence in the demonstration of safety is appropriate and sufficient to submit the construction licence application to the authorities. The assessment of long-term safety includes uncertainties, but these do not affect the basic conclusions on the long-term safety of the repository. (orig.)

  11. Disposal facility in Olkiluoto, description of above ground facilities in tunnel transport alternative

    International Nuclear Information System (INIS)

    Kukkola, T.

    2006-11-01

    The above ground facilities of the disposal plant on the Olkiluoto site are described in this report as they will be when the operation of the disposal facility starts in the year 2020. The disposal plant is visualised on the Olkiluoto site. Parallel construction of the deposition tunnels and disposal of the spent fuel canisters constitute the principal design basis of the disposal plant. The annual production of disposal canisters for spent fuel amounts to about 40. Production of 100 disposal canisters has been used as the capacity basis. Fuel from the Olkiluoto plant and from the Loviisa plant will be encapsulated in the same production line. The disposal plant will require an area of about 15 to 20 hectares above ground level. The total building volume of the above ground facilities is about 75000 m 3 . The purpose of the report is to provide the base for detailed design of the encapsulation plant and the repository spaces, as well as for coordination between the disposal plant and ONKALO. The dimensioning bases for the disposal plant are shown in the Tables at the end of the report. The report can also be used as a basis for comparison in deciding whether the fuel canisters are transported to the repository by a lift or a by vehicle along the access tunnel. (orig.)

  12. Disposal facility in olkiluoto, description of above ground facilities in lift transport alternative

    International Nuclear Information System (INIS)

    Kukkola, T.

    2006-11-01

    The above ground facilities of the disposal plant on the Olkiluoto site are described in this report as they will be when the operation of the disposal facility starts in the year 2020. The disposal plant is visualised on the Olkiluoto site. Parallel construction of the deposition tunnels and disposal of the spent fuel canisters constitute the principal design basis of the disposal plant. The annual production of disposal canisters for spent fuel amounts to about 40. Production of 100 disposal canisters has been used as the capacity basis. Fuel from the Olkiluoto plant and from the Loviisa plant will be encapsulated in the same production line. The disposal plant will require an area of about 15 to 20 hectares above ground level. The total building volume of the above ground facilities is about 75000 m 3 . The purpose of the report is to provide the base for detailed design of the encapsulation plant and the repository spaces, as well as for coordination between the disposal plant and ONKALO. The dimensioning bases for the disposal plant are shown in the Tables at the end of the report. The report can also be used as a basis for comparison in deciding whether the fuel canisters are transported to the repository by a lift or by a vehicle along the access tunnel. (orig.)

  13. Cost-effectiveness of managing Natura 2000 sites: an exploratory study for Finland, Germany, the Netherlands and Poland

    NARCIS (Netherlands)

    Wätzold, F.; Mewes, M.; Apeldoorn, van R.C.; Varjopuro, R.; Chmielewski, T.; Veeneklaas, F.R.; Kosola, M.L.

    2010-01-01

    Natura 2000 sites are expected to assure the long-term survival of Europe's most valuable and threatened species and habitats. It follows that successful management of the sites is of great importance. Next to goal attainment, cost-effectiveness is increasingly recognised as a key requirement for

  14. Laboratory measurements of the coefficient of thermal expansion of Olkiluoto drill core samples

    International Nuclear Information System (INIS)

    Aakesson, U.

    2012-04-01

    The coefficient of thermal expansion and the wet density has been determined on 22 specimens from the ONKALO drillholes ONK-PP167, ONK-PP199, ONK-PP224, ONK-PP225 and ONK-PP226, Olkiluoto, Finland. The coefficient of thermal expansion has been determined in the temperature interval 20-60 deg C. The results indicated that the thermal expansion was almost linear, and the coefficient of thermal expansion for the investigated specimens range between 3.2 and 14.4 x 10 -6 mm/mm deg C, and the wet density between 2,610 and 2,820 kg/m 3 . The granite pegmatite has slightly lower coefficient of thermal expansion and wet density than gneissic rocks. (orig.)

  15. Implications of the Fukushima accident of nuclear safety in Finland

    International Nuclear Information System (INIS)

    Valtonen, Keijo

    2012-01-01

    A severe accident took place in Japan at Fukushima Dai-ichi nuclear power plant in March 2011. The immediate cause of the accident was a tsunami caused by the earthquake and the fact that the consequences of large tsunamis were not adequately considered in the design of the plant. Although tsunamis are not considered a real threat in Europe, the European Council requested on 25 March 2011 the European Nuclear Safety Regulators' Group (ENSREG) and the European Commission to undertake a comprehensive and transparent risk and safety assessment (''stress test'') of European nuclear power plants [ENSREG 2011A]. This report is prepared to evaluate the safety provisions of Finnish Nuclear Power Plants as specified in the European ''stress tests''. The technical description is based on the Licensees' reports on the issues within these specifications [Fortum 2011; TVO 2011]. Furthermore, evaluation on the current situation carried out by Radiation and Nuclear Safety Authority (STUK) is provided, and the possibilities to further enhance safety in the Finnish NPPs are presented. According to the ENSREG specifications, earthquakes, flooding and extreme weather conditions were studied in the stress tests. In addition, consequences of losses of some safety functions and finally management of severe accidents were studied, irrespective of their probabilities. The European stress tests cover in Finland all the operating nuclear power plants (Loviisa 1 and 2, Olkiluoto 1 and 2) and the unit under construction (Olkiluoto 3). The intermediate storages of spent fuel in Loviisa and in Olkiluoto are included in the stress tests. The new NPP units to be constructed which do not yet have a construction license, (Fennovoima 1, Olkiluoto 4) are not considered in the European stress tests. (orig.)

  16. Characterization of Olkiluoto bacterial and archaeal communities by 454 pyrosequencing

    Energy Technology Data Exchange (ETDEWEB)

    Bomberg, M.; Nyyssoenen, M.; Itaevaara, M. [VTT Technical Research Centre of Finland, Espoo (Finland)

    2012-06-15

    Recent advancement in sequencing technologies, 'Next Generation Sequencing', such as FLX 454 pyrosequencing has made it possible to obtain large amounts of sequence data where previously only few sequences could be obtained. This technique is especially useful for the study of community composition of uncultured microbial populations in environmental samples. In this project, the FLX 454 pyrosequencing technique was used to obtain up to 20 000 16S rRNA sequences or 10 000 mRNA sequences from each sample for identification of the microbial species composition as well as for comparison of the microbial communities between different samples. This project focused on the characterization of active microbial communities in the groundwater at the final disposal site of high radioactive wastes in Olkiluoto by FLX 454 pyrosequencing of the bacterial and archaeal ribosomal RNA as well as of the mRNA transcripts of the dsrB gene and mcrA gene of sulphate reducing bacteria and methanogenic archaea, respectively. Specific emphasis was put on studying the relationship of active and latent sulphate reducers and methanogens by qPCR due to their important roles in deep geobiochemical processes connected to copper corrosion. Seven packered boreholes were sampled anaerobically in Olkiluoto during 2009-2010. Groundwater was pumped from specific depths and the microbial cells werecollected by filtration on a membrane. Active microbial communities were studied based on RNA extracted from the membranes and translated to copy DNA, followed by sequencing by 454 Tag pyrosequencing. A total of 27 different bacterial and 17 archaeal taxonomic groups were detected.

  17. Ground water chemistry and water-rock interaction at Olkiluoto

    International Nuclear Information System (INIS)

    Pitkaenen, P.; Front, K.

    1992-02-01

    Bedrock investigations for the final repository for low- and intermediate level wastes (VLJ repository) generated at the Olkiluoto (TVO-I and TVO-II) nuclear power plant, stareted in 1980. Since 1988 the area has been investigated for the final disposal of spent nuclear fuel. In the report the geochemistry at the nuclear waste investigation site, Olkiluoto, is evaluated. The hydrogeological data are collected from boreholes drilled down to 1000-m depth into Proterozoic crystalline bedrock. The interpretation is based on groundwater chemistry and isotope data, mineralogical data, and the structure and hydrology of the bedrock, using correlation diagrams and thermodynamic calculations (PHREEQE). The hydrogeochemistry and major processes controlling the groundwater chemistry are discussed. The groundwater types are characterized by water-rock interaction but they also show features of other origins. The fresh and brackish waters are contaminated by varying amounts of young meteoric water and brackish seawater. The saline water contains residues of possibly ancient hydrothermal waters, imprints of which are occasionally seen in the rock itself. Different mixing phenomenas are indicated by the isotope contents (O-l8/H-2, H-3) and the Ca/Cl, Na/Cl, HCO 3 /Cl, SO 4 /Cl, Br/Cl, SI(calcite)/SI(dolomite) ratios. The interaction between bedrock and groundwater is reflected by the behaviour of pH, Eh, Ca, Mg, Na, K, Fe, HCO 3 and S0 4 . Dissolution and precipitation of calcite and pyrite, and aluminosilicate hydrolysis play the major role in defining the groundwater composition of the above components

  18. Characterization of Olkiluoto bacterial and archaeal communities by 454 pyrosequencing

    Energy Technology Data Exchange (ETDEWEB)

    Bomberg, M; Nyyssoenen, M; Itaevaara, M [VTT Technical Research Centre of Finland, Espoo (Finland)

    2012-06-15

    Recent advancement in sequencing technologies, 'Next Generation Sequencing', such as FLX 454 pyrosequencing has made it possible to obtain large amounts of sequence data where previously only few sequences could be obtained. This technique is especially useful for the study of community composition of uncultured microbial populations in environmental samples. In this project, the FLX 454 pyrosequencing technique was used to obtain up to 20 000 16S rRNA sequences or 10 000 mRNA sequences from each sample for identification of the microbial species composition as well as for comparison of the microbial communities between different samples. This project focused on the characterization of active microbial communities in the groundwater at the final disposal site of high radioactive wastes in Olkiluoto by FLX 454 pyrosequencing of the bacterial and archaeal ribosomal RNA as well as of the mRNA transcripts of the dsrB gene and mcrA gene of sulphate reducing bacteria and methanogenic archaea, respectively. Specific emphasis was put on studying the relationship of active and latent sulphate reducers and methanogens by qPCR due to their important roles in deep geobiochemical processes connected to copper corrosion. Seven packered boreholes were sampled anaerobically in Olkiluoto during 2009-2010. Groundwater was pumped from specific depths and the microbial cells werecollected by filtration on a membrane. Active microbial communities were studied based on RNA extracted from the membranes and translated to copy DNA, followed by sequencing by 454 Tag pyrosequencing. A total of 27 different bacterial and 17 archaeal taxonomic groups were detected.

  19. Characterization of Olkiluoto bacterial and archaeal communities by 454 pyrosequencing

    International Nuclear Information System (INIS)

    Bomberg, M.; Nyyssoenen, M.; Itaevaara, M.

    2012-06-01

    Recent advancement in sequencing technologies, 'Next Generation Sequencing', such as FLX 454 pyrosequencing has made it possible to obtain large amounts of sequence data where previously only few sequences could be obtained. This technique is especially useful for the study of community composition of uncultured microbial populations in environmental samples. In this project, the FLX 454 pyrosequencing technique was used to obtain up to 20 000 16S rRNA sequences or 10 000 mRNA sequences from each sample for identification of the microbial species composition as well as for comparison of the microbial communities between different samples. This project focused on the characterization of active microbial communities in the groundwater at the final disposal site of high radioactive wastes in Olkiluoto by FLX 454 pyrosequencing of the bacterial and archaeal ribosomal RNA as well as of the mRNA transcripts of the dsrB gene and mcrA gene of sulphate reducing bacteria and methanogenic archaea, respectively. Specific emphasis was put on studying the relationship of active and latent sulphate reducers and methanogens by qPCR due to their important roles in deep geobiochemical processes connected to copper corrosion. Seven packered boreholes were sampled anaerobically in Olkiluoto during 2009-2010. Groundwater was pumped from specific depths and the microbial cells werecollected by filtration on a membrane. Active microbial communities were studied based on RNA extracted from the membranes and translated to copy DNA, followed by sequencing by 454 Tag pyrosequencing. A total of 27 different bacterial and 17 archaeal taxonomic groups were detected

  20. Integration and consistency testing of groundwater flow models with hydro-geochemistry in site investigations in Finland

    International Nuclear Information System (INIS)

    Pitkaenen, P.; Loefman, J.; Korkealaakso, J.; Koskinen, L.; Ruotsalainen, P.; Hautojaervi, A.; Aeikaes, T.

    1999-01-01

    In the assessment of the suitability and safety of a geological repository for radioactive waste the understanding of the fluid flow at a site is essential. In order to build confidence in the assessment of the hydrogeological performance of a site in various conditions, integration of hydrological and hydrogeochemical methods and studies provides the primary method for investigating the evolution that has taken place in the past, and for predicting future conditions at the potential disposal site. A systematic geochemical sampling campaign was started since the beginning of 1990's in the Finnish site investigation programme. This enabled the initiating of integration and evaluation of site scale hydrogeochemical and groundwater flow models. Hydrogeochemical information has been used to screen relevant external processes and variables for definition of the initial and boundary conditions in hydrological simulations. The results obtained from interpretation and modelling hydrogeochemical evolution have been employed in testing the hydrogeochemical consistency of conceptual flow models. Integration and testing of flow models with hydrogeochemical information are considered to improve significantly the hydrogeological understanding of a site and increases confidence in conceptual hydrogeological models. (author)

  1. Results of forest monitoring on Olkiluoto island in 2010

    International Nuclear Information System (INIS)

    Aro, L.; Huhta, A.-P.; Hoekkae, H.; Lindroos, A.-J.; Rautio, P.; Helmisaari, H.-S.

    2011-11-01

    Forest investigations carried out on Olkiluoto aim to monitor the state of the forest ecosystems, quantify Olkiluoto-specific processes taking place in the forests producing input data for the safety assessment of spent nuclear fuel disposal, and follow possible changes in the forest condition resulting from the intensive construction activities currently being carried out in the area. The forest investigations form a part of the monitoring programme being carried out on Olkiluoto Island under the management of Posiva Oy. This report focuses on activities performed on bulk deposition and forest intensive monitoring plots (MRK and FIP plots) in 2010. In general, the deposition levels in 2010 in the open area and in stand throughfall were quite comparable to those in earlier years, although sulphur and calcium depositions were somewhat higher in the open area than in earlier years (2004-2008). The soil solution quality in 2010 was also quite comparable to that in earlier years. The NH 4 -N and NO 3 -N concentrations were low at all depths in the mineral soil of the FIP plots 4, 10 and 11. Instead, nitrate concentrations were high in the soil solution on FIP14. There appeared to be a clear overall increase in sulphate concentrations with increasing depth on FIP4 and FIP10. Chloride concentrations in the soil solution were extremely high at all depths on all FIP plots throughout the monitoring period; it is clear that there is a considerable input of NaCl in the deposition derived from the sea. The concentrations of heavy metals (Cd, Cr, Ni, Pb) in the soil solution at all depths at Olkiluoto during 2004-2010 continued in many cases to be close to or below the limit of quantification. In 2010 the monthly level of transpiration in the Scots pine dominated stand was smaller in May and bigger in July than during previous years (2007-2009). Monthly transpiration in the Norway spruce dominated stand was clearly lower in 2010 than in 2007-2009, and there is a decreasing

  2. Results of forest monitoring on Olkiluoto island in 2010

    Energy Technology Data Exchange (ETDEWEB)

    Aro, L.; Huhta, A.-P.; Hoekkae, H.; Lindroos, A.-J.; Rautio, P. [Finnish Forest Research Institute, Vantaa (Finland); Helmisaari, H.-S. [Helsinki Univ. (Finland)

    2011-11-15

    Forest investigations carried out on Olkiluoto aim to monitor the state of the forest ecosystems, quantify Olkiluoto-specific processes taking place in the forests producing input data for the safety assessment of spent nuclear fuel disposal, and follow possible changes in the forest condition resulting from the intensive construction activities currently being carried out in the area. The forest investigations form a part of the monitoring programme being carried out on Olkiluoto Island under the management of Posiva Oy. This report focuses on activities performed on bulk deposition and forest intensive monitoring plots (MRK and FIP plots) in 2010. In general, the deposition levels in 2010 in the open area and in stand throughfall were quite comparable to those in earlier years, although sulphur and calcium depositions were somewhat higher in the open area than in earlier years (2004-2008). The soil solution quality in 2010 was also quite comparable to that in earlier years. The NH{sub 4}-N and NO{sub 3}-N concentrations were low at all depths in the mineral soil of the FIP plots 4, 10 and 11. Instead, nitrate concentrations were high in the soil solution on FIP14. There appeared to be a clear overall increase in sulphate concentrations with increasing depth on FIP4 and FIP10. Chloride concentrations in the soil solution were extremely high at all depths on all FIP plots throughout the monitoring period; it is clear that there is a considerable input of NaCl in the deposition derived from the sea. The concentrations of heavy metals (Cd, Cr, Ni, Pb) in the soil solution at all depths at Olkiluoto during 2004-2010 continued in many cases to be close to or below the limit of quantification. In 2010 the monthly level of transpiration in the Scots pine dominated stand was smaller in May and bigger in July than during previous years (2007-2009). Monthly transpiration in the Norway spruce dominated stand was clearly lower in 2010 than in 2007-2009, and there is a

  3. Refraction seismic surveys in the investigation trench TK3 area in Olkiluoto, Eurajoki 2004

    Energy Technology Data Exchange (ETDEWEB)

    Ihalainen, M. [Suomen Malmi Oy, Espoo (Finland)

    2005-03-15

    Posiva Oy submitted an application for the Decision in Principle to the Finnish Government in May 1999. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the Decision in Principle on the final disposal facility for spent nuclear fuel at Olkiluoto, Eurajoki in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, the ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) conducted refraction seismic surveys at Olkiluoto site in Eurajoki. The work was ordered by Posiva Oy. The field work was carried out during May and June 2004. On five profiles S70-S74 totally 1002.5 m was surveyed. The purpose of the work was to determine the overburden thickness and to study bedrock properties, e.g. eventual fractured zones. The work consisted of staking, levelling, seismic measurements, interpretation and reporting. Fieldwork and interpretation were concluded by May and June 2004. Previously in 2000 and 2002 Smoy has carried out 33.0 km of seismic surveys in the area. (orig.)

  4. Rock mechanics stability at Olkiluoto, Haestholmen, Kivetty and Romuvaara

    International Nuclear Information System (INIS)

    Johansson, E.; Rautakorpi, J.

    2000-02-01

    Posiva Oy is studying the suitability of the Finnish bedrock for the geological disposal of spent nuclear fuel at four sites, Olkiluoto in Eurajoki, Haestholmen in Loviisa, Kivetty in Aeaenekoski and Romuvaara in Kuhmo. To enable the rock properties to be specified in great detail, the site-selection research programme has included rock mechanics investigations such as the measurement of in-situ rock stress and laboratory tests on rock samples. This report presents the results of the rock mechanics analyses performed on the main rock types at the Olkiluoto, Romuvaara, Kivetty and Haestholmen sites. The objective of this study was to assess the near-field stability of the final disposal tunnels and deposition holes at each of the investigation sites. Two empirical methods and a numerical method based on three-dimensional element code (3DEC) were used the analysis tools. A statistical approach was used to select the necessary input data and to specify the cases being analysed. The stability of the KBS-3 and MLH (Medium Long Hole) repository concepts during the pre-closure and post-closure phases was analysed. The repository depths investigated lay between 300 m and 700 m. The empirical methods are based on the study of the ratios between rock strength and the in-situ stress which could result in possible fracturing of the rock mass. Interpretation of the numerical analyses is based on the assumption of an elastic distribution of stress around the disposal tunnel and the deposition hole and the brittle rock strength criterion. The results obtained in this study indicate that in general, the rock mechanics conditions during the pre-closure and post-closure phases at each of the investigated sites remain good and stable between the studied depth levels, especially when the deposition rooms are oriented in a direction parallel to the major in-situ stress. If the disposal tunnels are orientated in a direction perpendicular to the major in-situ stress, the resultant

  5. Oskarshamn site investigation. Bedrock geology - overview and excursion guide

    Energy Technology Data Exchange (ETDEWEB)

    Wahlgren, Carl-Henric (Geological Survey of Sweden, Uppsala (Sweden))

    2010-09-15

    Bearing in mind the significance of the bedrock data from the ground surface for the geological 3D modelling work, SKB decided to present excursion guides that serve in the demonstration of the bedrock geology at the ground surface in both the Forsmark and Laxemar-Simpevarp (this guide) areas. An excursion guide is also available for the Olkiluoto area in south-western Finland, which has been selected for the construction of a repository for the disposal of highly radioactive, spent nuclear fuel. The current excursion guide presents the bedrock geology and describes in detail the character of the bedrock at eight representative outcrops or outcrop areas at the ground surface in the site investigation area at Laxemar-Simpevarp and at one locality north of this area, i.e. at a total of nine localities

  6. Oskarshamn site investigation. Bedrock geology - overview and excursion guide

    International Nuclear Information System (INIS)

    Wahlgren, Carl-Henric

    2010-09-01

    Bearing in mind the significance of the bedrock data from the ground surface for the geological 3D modelling work, SKB decided to present excursion guides that serve in the demonstration of the bedrock geology at the ground surface in both the Forsmark and Laxemar-Simpevarp (this guide) areas. An excursion guide is also available for the Olkiluoto area in south-western Finland, which has been selected for the construction of a repository for the disposal of highly radioactive, spent nuclear fuel. The current excursion guide presents the bedrock geology and describes in detail the character of the bedrock at eight representative outcrops or outcrop areas at the ground surface in the site investigation area at Laxemar-Simpevarp and at one locality north of this area, i.e. at a total of nine localities

  7. Eurajoki Olkiluoto study on species of ground beetles and ants 2008

    International Nuclear Information System (INIS)

    Santaharju, J.; Helminen, S.-L.; Yrjoelae, R.

    2009-02-01

    The species of ants and Ground beetles at Olkiluoto in Eurajoki were studied in the summer of 2008 during two trapping periods: in June and August. The research goal was to clarify the species on Olkiluoto island of the earlier mentioned groups, at least at the family level, and to collect samples for further examination by Posiva. The trapping areas were selected at Olkiluoto in Posiva test monitoring sectors, a part of the trapping areas was the same as the earlier study. Species of ants, depending on their particular species, are a very dominating group of insects. The ants are the most important predators, scavengers and soil movers in Finnish forests. It looks as if the biomass of ants may be more than 10% of the biomass of all animals in certain areas of Finnish forests. In Finland there are about 60 species of ants that have been observed. They have been divided into four sub-groups, which are Myrmicinae, Formicinae, Ponerinae and Dolichoderinae. In Finland there are close to 300 species of ground beetles (Carabidae), which are divided into dozens of different families. The species, to a great extent, consist mostly of predatory insects that prey on microbes in field layers, but a part of them are specialized in feeding on flora. Ground beetles are usually divided into three groups according to their choice of habitat: Species that favour open biotopes, species that favour forests, and generalist species that can thrive in a variety of environments. Ground beetles also reflect changes in their living environment, and possibly they can be significant as socalled bio-indicators. Pitfall traps were used as the method of research. The preservative fluid used was ethanol (50%) with dishwashing liquid to remove surface tension. The points were located in various different biotopes in fields, meadows and forests. The data collected was defined as a minimum for the family level of Ground beetles and for ants to the species or species pairs. The species of Ground

  8. Eurajoki Olkiluoto study on species of ground beetles and ants 2008

    Energy Technology Data Exchange (ETDEWEB)

    Santaharju, J.; Helminen, S.-L.; Yrjoelae, R. (Environmental Research Yrjoelae Ltd, Helsinki (Finland))

    2009-02-15

    The species of ants and Ground beetles at Olkiluoto in Eurajoki were studied in the summer of 2008 during two trapping periods: in June and August. The research goal was to clarify the species on Olkiluoto island of the earlier mentioned groups, at least at the family level, and to collect samples for further examination by Posiva. The trapping areas were selected at Olkiluoto in Posiva test monitoring sectors, a part of the trapping areas was the same as the earlier study. Species of ants, depending on their particular species, are a very dominating group of insects. The ants are the most important predators, scavengers and soil movers in Finnish forests. It looks as if the biomass of ants may be more than 10% of the biomass of all animals in certain areas of Finnish forests. In Finland there are about 60 species of ants that have been observed. They have been divided into four sub-groups, which are Myrmicinae, Formicinae, Ponerinae and Dolichoderinae. In Finland there are close to 300 species of ground beetles (Carabidae), which are divided into dozens of different families. The species, to a great extent, consist mostly of predatory insects that prey on microbes in field layers, but a part of them are specialized in feeding on flora. Ground beetles are usually divided into three groups according to their choice of habitat: Species that favour open biotopes, species that favour forests, and generalist species that can thrive in a variety of environments. Ground beetles also reflect changes in their living environment, and possibly they can be significant as socalled bio-indicators. Pitfall traps were used as the method of research. The preservative fluid used was ethanol (50%) with dishwashing liquid to remove surface tension. The points were located in various different biotopes in fields, meadows and forests. The data collected was defined as a minimum for the family level of Ground beetles and for ants to the species or species pairs. The species of Ground

  9. Vertical and horizontal seismic profiling investigations at Olkiluoto, 2001

    Energy Technology Data Exchange (ETDEWEB)

    Cosma, C.; Enescu, N.; Adam, E.; Balu, L. [Vibrometric Oy (Finland)

    2003-03-01

    Vertical Seismic Profiling (VSP) and Horizontal Seismic Profiling (HSP) surveys were conducted during 2001 at Olkiluoto site in Eurajoki, Finland. The VSP investigations were carried out in four boreholes with ten shot points for each borehole. Two HSP lines were measured with receivers laid on the bottom of an artificial pond and ten source points located around the pond. Different receiver types were used for the VSP and (HSP) a 3-component geophone chain for VSP and a hydrophone chain for HSP. All surveys have been carried out with a VIBSIST-1000 source - a time- distributed swept-impact source - instead of explosives. With this source, the seismic signals are produced as rapid series of impacts, the impact intervals being monotonically increased to achieve a non- repeatable sequence. The VIBSIST-1000 uses a tractor-mounted hydraulic rock-breaker, powered through a computer controlled servo- hydraulic flow regulator. Using standard construction equipment ensures that the VIBSIST sources are safe, nondestructive and environmentally friendly. This also makes the method reliable and cost effective. The new VIBSIST source produces signals with levels of energy comparable to explosives. The VIBSIST appears to be more stable, but its most significant advantages are the low cost of preparation of the shot points and the speed of the acquisition. The wide diversity of reflection angles, the local variations of reflectivity and, generally, the relatively weak seismic response of faults and fractured zones in crystalline rock demand intensive processing. The first stage of the processing sequence focuses on eliminating such wave-fields as the direct P, direct S, tube-waves and ground-roll, so that the weaker later events, e.g. reflections, become visible. The second stage of processing consists mainly of Image Point (IP) filtering techniques, aimed at enhancing the reflected wave fields and at separating events generated by reflectors with different orientations. Imaging

  10. Cultural approach to the perception of risk. Analyzing concern about siting of a high-level nuclear waste facility in Finland

    International Nuclear Information System (INIS)

    Litmanen, T.

    1996-01-01

    The study of local residents' attitudes toward siting a high-level nuclear waste facility in Finland took place in three municipalities (Eurajoki, Kuhmo and Agnekoski), which are being considered possible host communities for the plant. The survey showed that the NIMBY phenomenon is a common reaction in two of the three municipalities, and in the third a polarization of opinions into two opposing camps is evident. The analysis of the data indicates that the opposition consist of people who have less education, less knowledge about the facility, lower incomes, and a lower occupational status. The social base of the proponents is the opposite. The persons most critical towards the possible siting can be found among women, older people, voters of the Greens, retired persons and farmers. People who welcome nuclear waste in their vicinity can be found among men, the middle-aged, voters of the Conservative Party and business owners. The study of the perception of possible negative impacts (health and safety, environmental, economic and social) showed that residents in Kuhmo and Adnekoski were more concerned about possible hazards than the residents of Eurajoki. According to the cultural approach, these findings must be contextualized. Eurajoka, which holds more favorable attitudes than Kuhmo and Agnekoski, hosts a nuclear power plant. In the two other communities the opposition is greater, because the residents are unfamiliar with nuclear technology. The thesis of the paper is that in order to understand different opinions about the facility, one must understand the cultural logic of risk perception. People evaluate the risk as individuals, but also as members of different reference groups and in the context of local, national and international circumstances

  11. Nuclear facility projects in Finland: quality of environmental impact assessment (EIA) processes

    International Nuclear Information System (INIS)

    Vaatainen, A.

    2001-01-01

    In Finland, three public EIA hearings arranged by the contact authority concerning nuclear facilities were organised in 1999: the EIAs of two reactors planned to be constructed in Eurajoki (Olkiluoto) and in Loviisa, and the EIA of a final disposal facility of spent nuclear fuel, to be situated either in Olkiluoto, Loviisa, Romuvaara or Kivetty. Additionally, an application for a decision-in-principle concerning a final disposal facility to be constructed in Olkiluoto was submitted. The Ministry of Trade and Industry is the contact authority in all nuclear projects in Finland. Probably due to the simultaneity of the processes and the great importance of nuclear facility projects to the whole of society, the public opinions did not include only views about environmental impacts of each project, but also opposing and overall views about the use of nuclear energy and its safety. As for the final disposal project, alternative methods were introduced and opposition to the project itself was expressed instead of or in addition to the environmental impacts. (author)

  12. Energy - Finland`s new trump card

    Energy Technology Data Exchange (ETDEWEB)

    Huopalahti, K. [Imatran Voima Oy, Vantaa (Finland)

    1994-12-31

    The energy sector in Finland is heavily constrained by the tough northern climate, meagre fuel reserves, an expensive infrastructure, the small domestic market and limited capital resources. However, Finland`s forest and metal industries have demanded low-cost energy, considering it vital for their existence and therefore for the prosperity of the whole country. Finland`s extensive foreign trade and open policies have also furthered this process; they have forced the industry on the one hand to face competition at home, and on the other to go abroad to compete there. The energy sector has risen to this ambitious challenge, at the same time developing into an independent industrial sector that can compete in the international market

  13. Influence of air mass source sector on variations in CO2 mixing ratio at a boreal site in northern Finland

    International Nuclear Information System (INIS)

    Aalto, T.; Hatakka, J.; Viisanen, Y.

    2003-01-01

    CO 2 mixing ratio in air masses coming from different source sectors was studied at Pallas measurement station in Lapland. Source sectors were defined using back trajectories and wind direction measurements. Air masses from the North and West sectors showed an annual variation of 17 ppm, possibly affected by a long range transported marine air. A larger variation of 20 ppm was observed in air masses from the more continental South and East sectors. During late autumn mixing ratios in air masses from the South sector were high in comparison with the other sectors. Different methods for a source sector definition were considered for the site, located in a contoured terrain. 52%-73% of wind direction-based source sector definitions agreed with trajectory- based definitions. However, the number of cases with reliable sector definitions may remain low when considering all observations. Different definition methods can cause differences of the order of 1 ppm in sectorially selected monthly mean CO 2 mixing ratios. (orig.)

  14. Advanced digital I and C technology in nuclear power plants. A success story from Finland and China

    International Nuclear Information System (INIS)

    Liebschner, T.; Heidowitzsch, B.

    2005-01-01

    FRAMATOME ANP together with Siemens PGL have just commissioned the I and C systems for the Chinese Nuclear Power Plant Tianwan Unit 1, design the I and C systems for the first European Pressurized Water Reactor Olkiluoto 3 in Finland and started one of the most extensive and ambitious modernization project in a nuclear power plant for Loviisa NPP in Finland. The presentation delivers an insight into the problematic of digital I and C systems integration and focuses on aspects regarding design criteria, Structure and test approaches. (author)

  15. Laboratory testing of gneissic rocks in Olkiluoto borehole OL-KR24

    International Nuclear Information System (INIS)

    Eloranta, P.

    2006-10-01

    The stress-strain behaviour of anisotropic gneissic rocks from Olkiluoto, Finland, was studied for a total of 25 rock mechanics tests. Samples were selected from borehole OLKR24 at a depth level of 417-442 m. Tests included 15 uniaxial compression tests, 10 indirect tensile strength tests and 6 triaxial compression tests. Strain gauges were installed in five samples to evaluate the anisotropic properties, and acoustic emission sensors were installed in ten samples to estimate the stress damage levels. The specimen preparation and tests were carried out at the Laboratory of Rock Engineering, Helsinki University of Technology, Finland. Specimens were tested under laboratory-air-dry conditions and were photographed before and after the tests. The values obtained for the uniaxial compressive strength were in the range 56.5 - 165.9 MPa and for the indirect tensile strength 7.7 - 12.1 MPa. The anisotropic ratio of Young's modulus, E/E', was of the order of 1.1. (orig.)

  16. Summary report of the experiences from TVO's site investigations

    International Nuclear Information System (INIS)

    Oehberg, A.; Saksa, P.; Ahokas, H.; Ruotsalainen, P.; Snellman, M.

    1994-05-01

    Teollisuuden Voima Oy (TVO) has completed preliminary site investigations at five sites in Finland. At the end of 1992 TVO presented the final report to the authorities. The preliminary site investigation phase 1986-1992 was conducted according to the investigation programme compiled by TVO. The aim of this report was to compile a report on experiences from TVOs site investigations. The main interest was focused on investigation strategies and the most important investigation methods for the conceptual modelling. The objective of the preliminary site investigations was to obtain data on the bedrock properties in order to evaluate the areas. The programme was divided into four stages, each stage having its own sub-objective. The site-specific investigation programme for each site included a large common part and a small site-specific part. The strategies (objectives) and experiences from different disciplines, geology, hydrogeochemistry, geophysics and geohydrology, are presented in the report. The conceptual modelling work procedure including both bedrock and groundwater modelling is described briefly using the Olkiluoto site as an example. Each of the other areas has undergone similar phases of work. The uncertainties associated with conceptual modelling are also discussed. The usefulness of the investigation strategy and the investigation methods for conceptual modelling is discussed in the report. Some new equipment, methods or enhancements that have not yet been used in TVOs site investigations have become new tools in site characterisation and are briefly presented in the report. 52 refs, 35 figs, 1 tab

  17. GPS operations at Olkiluoto, Kivetty and Romuvaara in 2006

    International Nuclear Information System (INIS)

    Ahola, J.; Koivula, H.; Poutanen, M.; Jokela, J.

    2007-05-01

    The GPS based deformation studies have been made at the investigation areas of Posiva since 1995, when the network of ten GPS pillars was established at Olkiluoto. The network of seven GPS pillars was built at Kivetty and Romuvaara during the year 1996. One pillar in each investigation area belongs to the Finnish permanent GPS network, FinnRef. 22 GPS measurement campaigns have been carried out at Olkiluoto since 1995, and 15 campaigns at Kivetty and Romuvaara. According to the time series of the GPS results 1/3 of the baselines at Olkiluoto have statistically significant change rates. However, the observed movements are smaller than ± 0.22 mm/a. The networks of Kivetty and Romuvaara are quite stabile expect one pillar at Romuvaara. There are five pillars, which have statistically significant horizontal velocities at Olkiluoto. These local velocity components are small but taking into account the standard deviations the largest velocity components seems to be reliably determined (maximum velocity is -0.23 mm/a ± 0.023 mm/a). The uniform scale for the GPS measurements made in different years is the basic condition for reliable results in the deformation analyses. At Olkiluoto a baseline for electronic distance measurements (EDM) was built in 2002. The baseline has been measured using EDM instruments simultaneously with the GPS observations. The comparison between the GPS and EDM results can solve a possible scale error of the GPS. The GPS network at Olkiluoto was extended in 2003. The new pillars were built close to Kuivalahti village and on a small island of Iso Pyrekari. According to the geological evidence it is expected that a fracture zone is located between the new stations, thus enabling the determination of possible deformations along the fracture zone. The new pillars have been observed since 2003, but the time series are still too short for reliable deformation studies. The local crustal deformations have been studied in GeoSatakunta project, too. This

  18. Operating experience feedback program at Olkiluoto NPP

    International Nuclear Information System (INIS)

    Kosonen, Mikko

    2002-01-01

    Recent review and development of the operating experience feedback program will be described. The development of the program has been based on several reviews by outside organizations. Main conclusions from these review reports and from the self assessment of safety performance, safety problems and safety culture on the basis of the operational events made by ASSET-method will be described. An approach to gather and analyze small events - so-called near misses - will be described. The operating experience program has been divided into internal and external operating experience. ASSET-methodology and a computer program assisting the analysis are used for the internal operating experience events. Noteworthy incidents occurred during outage are analyzed also by ASSET-method. Screening and pre analysis of the external operating experience relies on co-operation with ERFATOM, an organization of Nordic utilities for the exchange of nuclear industry experience. A short presentation on the performance of the Olkiluoto units will conclude the presentation. (author)

  19. The Finnish Experience with the Construction of Onkalo. Licensing of a repository for nuclear waste in Finland

    International Nuclear Information System (INIS)

    Avolahti, Jaana

    2014-01-01

    Pursuant to the Nuclear Energy Act (990/1987), a license holder whose operations result, or have resulted, in the generation of nuclear waste must perform all measures included in the management of nuclear waste and preparation thereof and bear all the costs of nuclear waste management. Under law, spent nuclear fuel is regarded as nuclear waste. According to the amendment made to the Nuclear Energy Act in 1994, nuclear waste generated in Finland must be handled, stored and permanently disposed of in Finland. Nuclear waste generated elsewhere may not be handled, stored and permanently disposed of in Finland. The Finnish nuclear legislation defines spent fuel as nuclear waste and requires that it has to be disposed of in the Finnish bedrock. Over 30 years of systematic R and D has been carried out to develop the repository concept, site selection, technologies, safety assessment and the regulatory approach. Activities are based on the Finnish Government's long term strategies since 1983. The stepwise development and future plans for disposal are presented in Table 1. The licensing procedure for a disposal facility has several steps that are similar to all nuclear facilities in Finland and are defined in Nuclear Energy Act (990/1987) and Decree (161/1988). These licensing steps are: - Decision in Principle (DiP); - Construction License; - Operational License. An Environmental Impact Assessment (EIA) shall be conducted prior to the first authorization step of a major nuclear waste facility. The EIA procedure for the final disposal of spent nuclear fuel from three units of the Olkiluoto nuclear power plant and two units of the Loviisa nuclear power plant was carried out in 1998-1999 and extended to one more unit at Olkiluoto in 2008- 2009. Pursuant to the Nuclear Energy Act, before making the DiP the Government shall ascertain whether the municipality planned as the location of the nuclear facility is in favour of the facility, and ensure that no facts indicating a

  20. Results of monitoring at Olkiluoto in 2013, rock mechanics

    International Nuclear Information System (INIS)

    Johansson, E.

    2014-10-01

    The rock mechanics monitoring at Olkiluoto concentrates on the assessment of potential tectonic movements and stability of the bedrock. The rock mechanics monitoring programme 2013 consisted of seismic measurements, GPS measurements, surface levelling measurements and temperature measurements at Olkiluoto and vicinity and displacement measurements, temperature measurements and visual tunnel observations made in the ONKALO. The Posiva's microseismic network consists of 17 seismic stations and 21 triaxial sensors. Five stations are in the ONKALO. In spite of few breaks the network operated continuously and well during 2013. The number of located events (436) was slightly more than in 2012, but much less than in 2011. Nearly half of the observed explosions (237) in 2013 occurred inside the seismic semi-regional area and especially inside the seismic ONKALO block (137). One small induced earthquake (M L = -1.8) was detected at the depth of 429 m and was probably associated with smaller branches of the brittle fracture zone (OL-BFZ045). According to the seismic monitoring the rock mass has been stable in 2013. The local GPS network consists of 18 stations. Six new stations were set up for permanent tracking during 2013 and in total 12 permanent stations are now operating continuously. Manual measurements were carried out twice in 2013. Most of the inner network baselines showed very small motions as in the previous years: 75% of change rates were smaller than 0.10 mm/y. Roughly one third of the change rates are statistically significant. The surface levelling network currently consists of 87 fixed measuring points. During 2013 all the measuring loops were measured. The results indicated local subsidence area in the ONKALO loop and the rising area in the VLJ loop. Mean deformation rate has been +0.05 mm/y. Only elevation of one benchmark in the GPS station loop has changed more than one millimetre. The continuous displacement measurements in the technical rooms of

  1. Results of monitoring at Olkiluoto in 2013, rock mechanics

    Energy Technology Data Exchange (ETDEWEB)

    Johansson, E. (ed.) [Saanio and Riekkola Oy, Helsinki (Finland)

    2014-10-15

    The rock mechanics monitoring at Olkiluoto concentrates on the assessment of potential tectonic movements and stability of the bedrock. The rock mechanics monitoring programme 2013 consisted of seismic measurements, GPS measurements, surface levelling measurements and temperature measurements at Olkiluoto and vicinity and displacement measurements, temperature measurements and visual tunnel observations made in the ONKALO. The Posiva's microseismic network consists of 17 seismic stations and 21 triaxial sensors. Five stations are in the ONKALO. In spite of few breaks the network operated continuously and well during 2013. The number of located events (436) was slightly more than in 2012, but much less than in 2011. Nearly half of the observed explosions (237) in 2013 occurred inside the seismic semi-regional area and especially inside the seismic ONKALO block (137). One small induced earthquake (M{sub L} = -1.8) was detected at the depth of 429 m and was probably associated with smaller branches of the brittle fracture zone (OL-BFZ045). According to the seismic monitoring the rock mass has been stable in 2013. The local GPS network consists of 18 stations. Six new stations were set up for permanent tracking during 2013 and in total 12 permanent stations are now operating continuously. Manual measurements were carried out twice in 2013. Most of the inner network baselines showed very small motions as in the previous years: 75% of change rates were smaller than 0.10 mm/y. Roughly one third of the change rates are statistically significant. The surface levelling network currently consists of 87 fixed measuring points. During 2013 all the measuring loops were measured. The results indicated local subsidence area in the ONKALO loop and the rising area in the VLJ loop. Mean deformation rate has been +0.05 mm/y. Only elevation of one benchmark in the GPS station loop has changed more than one millimetre. The continuous displacement measurements in the technical rooms

  2. Optical imaging of the boreholes KR37, KR37B and KR38 at Olkiluoto 2005

    International Nuclear Information System (INIS)

    Majapuro, J.

    2006-02-01

    Suomen Malmi Oy conducted optical imaging surveys of the boreholes KR37, KR37B and KR38 at the Olkiluoto site in Eurajoki during September 2005. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and preliminary processing of the images. The report describes the field operation, equipment as well as processing procedures and shows the obtained results and their quality through example images. The raw and processed data are delivered digitally in WellCAD format. The images are also attached to the appendix CD of this report in Adobe Acrobat PDF-format. (orig.)

  3. Environmental radioactivity data of Olkiluoto in 1977-1983 and 2002-2003

    International Nuclear Information System (INIS)

    Roiviainen, P.

    2005-05-01

    In this report, data of the environmental radiation surveillance programme of the Olkiluoto nuclear power plant is published in a collected format for further reference. The data reported consists of analysis results of selected environmental media and indicator organisms representing human food web, and it covers periods of 1977-1983 and 2002-2003. In addition to sampling and analysis results, also a concise description of data acquisition methods - when still traceable - and handling is provided as well as locations of sampling sites. (orig.)

  4. GPS operations at Olkiluoto, Kivetty and Romuvaara in 2010

    International Nuclear Information System (INIS)

    Kallio, U.; Nyberg, S.; Koivula, H.; Jokela, J.; Poutanen, M.

    2011-11-01

    The Finnish Geodetic Institute (FGI) has studied crustal deformations in co-operation with the Posiva Oy since 1994, when a network of ten pillars for GPS observations was established at Olkiluoto. In 2010 the local GPS network at Olkiluoto consisted of 14 concrete pillars. The whole network has been measured twice a year in the static GPS campaigns with 24 h sessions. The four new pillars were established in 2010 and the permanent measurements on them will start in 2011. The network of seven GPS pillars was built at Kivetty and Romuvaara during the year 1996. One pillar in each investigation area belongs to the Finnish permanent GPS network, FinnRef. A total of 28 GPS measurement campaigns have been carried out at Olkiluoto since 1995, and 18 campaigns at Kivetty and Romuvaara. At Olkiluoto a baseline for electronic distance measurements (EDM) was built in 2002. The baseline has been measured in connection to the GPS observations using the EDM instrument Kern ME5000 Mekometer. The GPS operations in 2010 included the two GPS campaigns at Olkiluoto, GPS campaigns at Kivetty and Romuvaara, EDM baseline measurements at Olkiluoto, and the control marker measurements with the tachymeter at Olkiluoto. All GPS data history was reprocessed with Bernese GPS software using the new processing strategy tested in 2009. The results were analysed by computing the change rates of the baselines and estimating horizontal velocities for the pillars using the barycenter of the velocities as a reference. In the Olkiluoto inner network 80 percent of the change rates were smaller than 0.10 mm/a. Roughly one fourth of the change rates could be considered as statistically significant (change rate larger than 3 σ. The statistically significant change rates were mainly related to the Olkiluoto permanent station (GPS1) and to the pillar GPS5, which had also the maximum change rate (0.21 ± 0.03 mm/a). In Olkiluoto outer network the maximum and statistically significant change rates are

  5. GPS operations at Olkiluoto, Kivetty and Romuvaara in 2010

    Energy Technology Data Exchange (ETDEWEB)

    Kallio, U.; Nyberg, S.; Koivula, H.; Jokela, J.; Poutanen, M. [Finnish Geodetic Institute, Masala (Finland)

    2011-11-15

    The Finnish Geodetic Institute (FGI) has studied crustal deformations in co-operation with the Posiva Oy since 1994, when a network of ten pillars for GPS observations was established at Olkiluoto. In 2010 the local GPS network at Olkiluoto consisted of 14 concrete pillars. The whole network has been measured twice a year in the static GPS campaigns with 24 h sessions. The four new pillars were established in 2010 and the permanent measurements on them will start in 2011. The network of seven GPS pillars was built at Kivetty and Romuvaara during the year 1996. One pillar in each investigation area belongs to the Finnish permanent GPS network, FinnRef. A total of 28 GPS measurement campaigns have been carried out at Olkiluoto since 1995, and 18 campaigns at Kivetty and Romuvaara. At Olkiluoto a baseline for electronic distance measurements (EDM) was built in 2002. The baseline has been measured in connection to the GPS observations using the EDM instrument Kern ME5000 Mekometer. The GPS operations in 2010 included the two GPS campaigns at Olkiluoto, GPS campaigns at Kivetty and Romuvaara, EDM baseline measurements at Olkiluoto, and the control marker measurements with the tachymeter at Olkiluoto. All GPS data history was reprocessed with Bernese GPS software using the new processing strategy tested in 2009. The results were analysed by computing the change rates of the baselines and estimating horizontal velocities for the pillars using the barycenter of the velocities as a reference. In the Olkiluoto inner network 80 percent of the change rates were smaller than 0.10 mm/a. Roughly one fourth of the change rates could be considered as statistically significant (change rate larger than 3 {sigma}. The statistically significant change rates were mainly related to the Olkiluoto permanent station (GPS1) and to the pillar GPS5, which had also the maximum change rate (0.21 {+-} 0.03 mm/a). In Olkiluoto outer network the maximum and statistically significant change rates

  6. Safety case for the disposal of spent nuclear fuel at Olkiluoto. Surface and near-surface hydrological modelling in the biosphere assessment BSA-2012

    International Nuclear Information System (INIS)

    Karvonen, T.

    2013-05-01

    The Finnish nuclear waste disposal company, Posiva Oy, is planning an underground repository for spent nuclear fuel to be constructed on the island of Olkiluoto on the south-west coast of Finland. This study is part of the biosphere assessment (BSA-2012) within the safety case for the repository. The surface hydrological modelling described in this report is aimed at providing link between radionuclide transport in the geosphere and in the biosphere systems. The SVAT-model and Olkiluoto site scale surface hydrological model were calibrated and validated in the present day conditions using the input data provided by the Olkiluoto Monitoring Programme (OMO). During the next 10 000 years the terrain and ecosystem development is to a large extent driven by the postglacial crustal uplift. UNTAMO is a GIS toolbox developed for simulating land-uplift driven or other changes in the biosphere. All the spatial and temporal input data (excluding meteorological data) needed in the surface hydrological modelling were provided by the UNTAMO toolbox. The specific outputs given by UNTAMO toolbox are time-dependent evolution of the biosphere objects. They are continuous and sufficiently homogeneous sub-areas of the modelled area that could potentially receive radionuclides released from the repository. Possible ecosystem types for biosphere objects are coast, lake, river, forest, cropland, pasture and wetland. The primary goal of this study was to compute vertical and horizontal water fluxes in the biosphere objects. These data will be used in the biosphere radionuclide transport calculations. The method adopted here is based on calculating average vertical and horizontal fluxes for biosphere objects from the results of the full 3D-model. It was not necessary to develop any simplified hydrological model for the biosphere objects. This report includes modelling results from for the Reference Case (present day climate) and Terr M axAgri Case (maximum extent of agricultural areas and

  7. Properties of bituminization product from Olkiluoto power plant

    International Nuclear Information System (INIS)

    Valkiainen, M.; Vuorinen, U.

    1985-09-01

    In Finland, disposal into repositories excavated into bedrock on the present power plant sites is considered to be the most feasible alternative for the low- and intermediate level wastes. The Nuclear Waste Commission of the Finnish power companies has sponsored mainly experimental research work on long-term properties of bituminized ion exchange resin performed in the Reactor Laboratory of the Technical Research Centre of Finland since 1981. This report presents results on follow-up measurements of the leach tests started in 1981 and results on new leach tests with cement equilibrated water. Swelling of the bituminization product caused by water uptake is considered important. Both unrestricted and restricted swelling measurements were performed and are reported here. In addition to leaching and swelling also radiolytic gas generation and pH-changes of the leachant are discussed

  8. World-class outage performance of the Olkiluoto nuclear power plant

    International Nuclear Information System (INIS)

    Paavola, M.

    1998-01-01

    The production of the Olkiluoto power plant units covered 17% of the electricity consumption in Finland in 1997; the total share of nuclear energy was 27% of the electricity consumed in the country. Based on Finnish experience, nuclear energy is a safe, environmentally friendly and economic way to produce electricity provided that the plants and their personnel are well taken care of. TVO's policy is to keep the plant units in good condition and technically modern. This requires continuous investments in the plant. In maintenance, attention is paid to monitoring the condition of the plant and to preventive maintenance aiming at avoiding disturbances in production. TVO has chosen continuous development as the operational line develops the plant by annual investments and performs the necessary modifications during planned annual outages trying to avoid long production interruptions. The load factors of the Olkiluoto nuclear power plant have been high. The average load factor during the last decade was over 93%. The most significant single factor in the production deficits is the amount or electricity, which has not been produced because of the annual outages. Due to this, special attention has been paid to the performance of the annual outages. TVO aims at continuous development of the annual outage procedure. A centralized task management system makes it possible to perform simultaneously more tasks than before. The company has also invested in equipment and systems, which ease and speed up servicing. Normal outage length varies between 10 and 16 days. By keeping the plant units as modern as possible and in good condition we facilitate reaching TVO's target, which is also stated in TVO's slogan 'always 40 years lifetime'. (author)

  9. Finnish EPR Olkiluoto 3. The world's first third-generation reactor now under construction

    International Nuclear Information System (INIS)

    2007-01-01

    The EPR was developed by Framatome and Siemens KWU (the nuclear division of Siemens), whose nuclear activities were combined in January 2001 to form Framatome ANP, now AREVA NP. The French electricity utility EDF (Electricite de France), together with the major German utilities, played an active role in the project. The safety authorities of the two countries joined forces to bring their respective safety standards into line and draw up joint design rules for the new reactor. On December 18, 2003, the consortium formed by AREVA and Siemens - and led by AREVA - signed a contract with TVO for the turnkey construction of the EPR. The overall Olkiluoto 3 project cost has been estimated by TVO at around euros 3 Billion. TVO is responsible for the overall project management and licensing process with the Finnish Safety Authority STUK. In the pre-qualification phase, STUK concluded that the EPR can meet the Finnish licensing requirements. All specific comments will be taken into account for the realization of the project. In January 2005, STUK emphasized in its safety assessment that the evolutionary EPR design compared to predecessor product lines has been further enhanced by AREVA. This paper presents first, The Finnish energy situation (Electricity consumption and supply, Finland's Kyoto CO 2 cutback, Competitiveness of nuclear power), and then the EPR in Olkiluoto (General schedule of responsibilities, Important milestones of the project). Finally, the EPR third-generation and advanced reactor is presented with its position in the international competition (Targeted design objectives, Main characteristics, competitiveness, safety, Additional measures to prevent the occurrence of events likely to damage the core, Increased protection against the consequences of core melt)

  10. Stable elements and radionuclides in shoreline alder stands at Olkiluoto in 2005

    International Nuclear Information System (INIS)

    Roivainen, P.

    2006-08-01

    In Finland, the final disposal of spent nuclear fuel from Finnish nuclear power plants is to take place in a repository, which will be built in Olkiluoto bedrock. According to the current plans, operation of the facility will start in 2020. Before this, a safety case has to be drawn up to substantiate the safety of the final disposal solution. The drawing up of the safety case also involves an assessment of impact on organisms other than human. Several radionuclides have a stable chemical analogue. Chemical analogues often display similar behaviour in the forest ecosystem. For this reason, information about radionuclides can also be obtained by studying stable elements. The purpose of this thesis was to study the migration of elements, radionuclides in particular, in the food webs of the Olkiluoto forest ecosystem. The objective was to produce concentration ratios between the various sub-components of the forest ecosystem. These ratios can be utilised in modelling. Three alder stands on the shores of Olkiluoto were used as monitoring plots. Littoral alder stands are an important biotope in terms of a recipient of the potential radionuclide contamination from the repository. Yet, research on littoral alder stands has so far been quite limited. From all the monitoring plots, a sample was taken of humus, mineral soil, understorey, plant roots and forest litter. Small mammals and earthworms were also to be caught from the monitoring plots, but no earthworms could be caught in any of the areas. All the collected samples were analysed for element concentrations using the ICP-AES method. Soil and plant samples were also analysed with a gamma spectrometer for activity concentrations of gamma active radionuclides. Activity concentrations of Cs-137 and K-40 could be determined in all soil and plant samples. The highest activity concentration of Cs-137 was found in humus, and the lowest in mineral soil. The activity concentration of K-40 was at its highest in mineral soil and

  11. Safety case for the disposal of spent nuclear fuel at Olkiluoto - Synthesis 2012

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-12-15

    TURVA-2012 is Posiva's safety case in support of the Preliminary Safety Analysis Report (PSAR 2012) and application for a construction licence for a spent nuclear fuel repository. Consistent with the Government Decisions-in- Principle, this foresees a repository developed in bedrock at the Olkiluoto site according to the KBS-3 method, designed to accept spent nuclear fuel from the lifetime operations of the Olkiluoto and Loviisa reactors. Synthesis 2012 presents a synthesis of Posiva Oy's Safety Case 'TURVA-2012' portfolio. It summarises the design basis for the repository at the Olkiluoto site, the assessment methodology and key results of performance and safety assessments. It brings together all the lines of argument for safety, evaluation of compliance with the regulatory requirements, and statement of confidence in long-term safety and Posiva's safety analyses. The TURVA-2012 safety case demonstrates that the proposed repository design provides a safe solution for the disposal of spent nuclear fuel, and that the performance and safety assessments are fully consistent with all the legal and regulatory requirements related to long-term safety as set out in Government Decree 736/2008 and in guidance from the nuclear regulator - the STUK. Moreover, Posiva considers that the level of confidence in the demonstration of safety is appropriate and sufficient to submit the construction licence application to the authorities. The assessment of long-term safety includes uncertainties, but these do not affect the basic conclusions on the long-term safety of the repository. (orig.)

  12. GPS Operations at Olkiluoto, Kivetty and Romuvaara in 2005

    International Nuclear Information System (INIS)

    Ahola, J.; Ollikainen, M.; Koivula, H.; Jokela, J.

    2006-07-01

    The GPS based deformation studies has been made at the investigation areas of Posiva since 1995, when the network of ten GPS pillars was established at Olkiluoto. The network of seven GPS pillars was built at Kivetty and Romuvaara during the year 1996. One pillar in each investigation area belongs to the Finnish permanent GPS network, FinnRef. Twenty GPS measurement campaigns have been carried out at Olkiluoto since 1995, and fourteen campaigns at Kivetty and Romuvaara. According to the time series of the GPS results 1/3 of the baselines at Olkiluoto have statistically significant change rates. However, the observed movements are smaller than ± 0.22 mm/a. There are no statistically signicant movements at Kivetty and Romuvaara expect one pillar at Romuvaara. There are five pillars, which have statistically significant horizontal velocities at Olkiluoto. The local velocity components are small but taking into account the standard deviations the largest velocity components seems to be reliable (maximum velocity is - 0.25 mm/a ± 0.025 mm/a). The uniform scale for the GPS measurements made in different years is the basic condition for reliable results in the deformation analyses. At Olkiluoto a baseline for electronic distance measurements (EDM) was built in 2002. The baseline has been measured using EDM instruments simultaneously with the GPS observations. The comparison between the GPS and EDM results to show a possible scale error of the GPS. The GPS network at Olkiluoto was enlarged in 2003. The new pillars were built close to Kuivalahti village and on a small island of Iso Pyrekari, both north from Olkiluoto. According to the geological evidence it is expected that a fracture zone is located between the new stations, thus enabling the determination of possible deformations along the fracture zone. The new pillars have been observed five times since 2003, but the time series are still too short for reliable deformation studies. Including the new pillars the local

  13. Results of Monitoring at Olkiluoto in 2010. Rock Mechanics

    Energy Technology Data Exchange (ETDEWEB)

    Lahti, M [ed.; Siren, T

    2011-12-15

    The rock mechanical monitoring at Olkiluoto concentrates on the assessment of potential tectonic movements and stability of the bedrock. The construction of ONKALO is not expected to induce large-scale movements of the rock blocks or affect the rate of isostatic uplift but the evaluation of any tectonic events is important for the safety assessment. The monitoring consists of seismic measurements, GPS measurements and precise levelling campaigns at Olkiluoto and vicinity and extensometer and convergence measurements carried out in ONKALO. Posiva established a local seismic network of six stations on the island of Olkiluoto in 2002. After that the number of seismic stations has increased gradually. In 2010 the permanent seismic network consists of 15 seismic stations and 20 triaxial sensors. The purpose of the microearthquake measurements at Olkiluoto is to improve understanding of the structure, behaviour and long term stability of the bedrock. The investigation area includes two target areas. The larger target area, called seismic semiregional area, covers the Olkiluoto Island and its surroundings. The purpose is to monitor explosions and tectonic earthquakes in regional scale inside that area. The smaller target area is called the seismic ONKALO block, which is a 2 km *2 km *2 km cube surrounding the ONKALO. It is assumed that all the expected excavation induced events occur within this volume. At the moment the seismic ONKALO block includes ten seismic stations. An additional task of monitoring is related to safeguarding of the ONKALO. This report gives the results of microseismic monitoring during 2010.

  14. Results of Monitoring at Olkiluoto in 2010. Rock Mechanics

    International Nuclear Information System (INIS)

    Lahti, M.; Siren, T.

    2011-12-01

    The rock mechanical monitoring at Olkiluoto concentrates on the assessment of potential tectonic movements and stability of the bedrock. The construction of ONKALO is not expected to induce large-scale movements of the rock blocks or affect the rate of isostatic uplift but the evaluation of any tectonic events is important for the safety assessment. The monitoring consists of seismic measurements, GPS measurements and precise levelling campaigns at Olkiluoto and vicinity and extensometer and convergence measurements carried out in ONKALO. Posiva established a local seismic network of six stations on the island of Olkiluoto in 2002. After that the number of seismic stations has increased gradually. In 2010 the permanent seismic network consists of 15 seismic stations and 20 triaxial sensors. The purpose of the microearthquake measurements at Olkiluoto is to improve understanding of the structure, behaviour and long term stability of the bedrock. The investigation area includes two target areas. The larger target area, called seismic semiregional area, covers the Olkiluoto Island and its surroundings. The purpose is to monitor explosions and tectonic earthquakes in regional scale inside that area. The smaller target area is called the seismic ONKALO block, which is a 2 km *2 km *2 km cube surrounding the ONKALO. It is assumed that all the expected excavation induced events occur within this volume. At the moment the seismic ONKALO block includes ten seismic stations. An additional task of monitoring is related to safeguarding of the ONKALO. This report gives the results of microseismic monitoring during 2010

  15. Updated and integrated modelling of the 1995 - 2008 Mise-a-la-masse survey data in Olkiluoto

    International Nuclear Information System (INIS)

    Ahokas, T.; Paananen, M.

    2010-01-01

    Posiva Oy prepares for disposal of spent nuclear fuel into bedrock focusing in Olkiluoto, Eurajoki. This is in accordance of the Decision-in-Principle of the State Council in 2000, and ratification by the Parliament in 2001. The ONKALO underground characterization premises have been constructed since 2004. Posiva Oy is aiming for submitting the construction licence application in 2012. To support the compilation of the safety case and repository and ONKALO design and construction, an integrated Olkiluoto site Description including geological, rock mechanics, hydrogeological and hydrogeochemical models will be depicted. Mise-a-la-masse (MAM) surveys have been carried out in the Olkiluoto area since 1995 to follow electric conductors from drillhole to drillhole, from drillhole to the ground surface and also between the ONKALO access tunnel and drillholes or the ground surface. The data and some visualisation of the data have been presented as part of reporting of the 1995 and 2008 surveys. The work presented in this paper includes modelling of all the measured data and combining single conductors modelled from different surveys to conductive zones. The results from this work will be used in updating the geological and hydrogeological models of the Olkiluoto site area. Several electrically conductive zones were modelled from the examined data, many of them coincide with the known brittle deformation zones but also indications of many so far unknown zones were detected. During the modelling Comsol Multiphysics software for calculating theoretical potential field anomalies of different models was tested. The test calculations showed that this software is useful in confirming the modelling results, especially in complicated cases. (orig.)

  16. Dissolved nitrogen transformations and microbial community structure in the organic layer of forest soils in Olkiluoto in 2006

    International Nuclear Information System (INIS)

    Potila, H.; Sarjala, T.; Aro, L.

    2007-02-01

    Carbon (C) and nitrogen (N) cycles in the ecosystem are strongly coupled. Biomass, structure and activity of the bacterial and fungal community are the key factors influencing C and N cycles. Changes in the function of soil microbial community can be a signal of plant responses to environmental changes. Dissolved N compounds, microbial biomass, microbial activity, fungal community structure and functional diversity of microbial communities were measured in September 2006 from five monitoring plots on Olkiluoto to assess information about soil microbial community structure and activity. High within and between variation in the studied plots were detected. However, in this study the values and their variation in the level of N mineralisation, dissolved N compounds, fungal biomass and microbial community structure in the studied plots were within a normal range in comparison with other published data of similar forest types in Finland. (orig.)

  17. Emergency preparedness in Finland

    International Nuclear Information System (INIS)

    Koivukoski, J.

    1993-01-01

    Although the menace of nuclear war still persists, the focus in national emergency preparedness in Finland is presently on emergencies involving nuclear installations. The nuclear power plants, nuclear submarines and other installations in the former USSR are a major reason for this. In this article the main features and organization of emergency preparedness in Finland are described. (orig.)

  18. Radioactivity of sludge in Finland in 1987

    International Nuclear Information System (INIS)

    Puhakainen, M.; Rahola, T.

    1989-05-01

    Sewage sludge from municipal wastewater treatment plants was studied to determine its radionuclide concentrations. Measurements were made to find out whether any radionuclides from the nuclear power stations at Loviisa and Olkiluoto and from hospitals and medical laboratories could be detected in sludge additional to those originating from global and Chernobyl fallout. In the treatment process of water, aluminium sulphate sludge is developed at treatment plants using surface water. This kind of sludge was measured since it also concentrates radionuclides. Fallout nuclides from the Chernobyl nuclear power station after the accident predominated in all sewage sludge samples in Finland. In 1987 six different radionuclides originating from the Chernobyl fallout were detected in sewage sludge. In spring when the snow melted and large quantities of run off water flowed into the treatment plants, the activity concentrations clearly increased, but then started decreasing again. At the end of the year the highest measured 137 Cs activity concentrations were below 1000 Bq kg -1 dry weight. The highest activity concentration in sludge originated from iodine used fro medical purposes

  19. Results of monitoring at Olkiluoto in 2009. Rock mechanics

    International Nuclear Information System (INIS)

    Lahti, M.; Hakala, M.

    2010-09-01

    The rock mechanical monitoring at Olkiluoto concentrates on the assessment of potential tectonic movements and stability of the bedrock. The construction of ONKALO is not expected to induce large-scale movements of the rock blocks or affect the rate of isostatic uplift but the evaluation of any tectonic events is important for the safety assessment. The monitoring consists of seismic measurements, GPS measurements and precise levelling campaigns at Olkiluoto and vicinity and additionally extensometer and convergence measurements carried out in ONKALO. Posiva established a local seismic network of six stations on the island of Olkiluoto in 2002. The number of seismic stations has increased gradually being in 2009 altogether 14. The purpose of the microearthquake measurements at Olkiluoto is to improve understanding of the structure, behaviour and long term stability of the bedrock. The investigation area includes two target areas. The larger target area, called seismic semi-regional area, covers the Olkiluoto Island and its surroundings. The purpose is to monitor explosions and tectonic earthquakes in regional scale. The smaller target area is s called the seismic ONKALO block, which is a 2 km *2 km *2 km cube surrounding the ONKALO. All the expected excavation induced events assumingly occur within this volume. At the moment the seismic ONKALO block includes 10 seismic stations. An additional task of monitoring is related to safeguarding of the ONKALO. The seismic network has operated continuously in 2009 and during the year altogether 1256 events have been located in the Olkiluoto area. Most of them (1161) are explosions that occurred inside the seismic semi-regional area and especially inside the seismic ONKALO block (1135 events)

  20. Greenfield nuclear power for Finland

    Energy Technology Data Exchange (ETDEWEB)

    Saarenpaa, Tapio

    2010-09-15

    In Finland, licensing for new nuclear power is ongoing. The political approval is to be completed in 2010. Fennovoima's project is unique in various ways: (i) the company was established only in 2007, (ii) its ownership includes a mixture of local energy companies, electricity-intensive industries and international nuclear competence through E.ON, and (iii) it has two alternative greenfield sites. There are five prerequisites for a successful nuclear power project in a transparent democracy of today: (1) need for additional power capacity, (2) actor prepared to invest, (3) established competence, (4) available site, (5) open communications, and (6) favorable public opinion.

  1. Nuclear power situation in Finland

    Energy Technology Data Exchange (ETDEWEB)

    Miettinen, J K

    1976-01-01

    Finland plans to have its future energy policy as well-balanced and economical as possible. Dependence on oil has to be reduced and savings have to be achieved wherever possible. Some growth of energy demand will be inevitable, and most of this growth has to be nuclear. Practically all hydropower that can be reasonably exploited is being utilized already. Finland has an abundance of peat, but it can be economically used only as a regional source of energy. This leaves, as the only real alternatives for the coming decennia, coal and fission; of the two, fission is evidently the better choice. Although other forms of energy such as fusion, solar, tidal, and wind energy have to be studied as longer-range alternatives. Four nuclear power plants are presently under construction in Finland and at least a few additional ones will evidently be built before 1990. Several of them will probably be of the combined district heat and electricity-producing type. The planning of nuclear energy has recently become complicated due to financing difficulties, uncertainties regarding long-range fuel services, and public opposition. The latter is partly caused by lack of information, partly by fears of a change of life-style in communities near the planned power plant sites. (From Conclusions)

  2. Core drilling of deep drillhole OL-KR54 at Olkiluoto in Eurajoki 2010

    International Nuclear Information System (INIS)

    Toropainen, V.

    2010-11-01

    As a part of the confirming site investigations at Olkiluoto, Suomen Malmi Oy (Smoy) core drilled a 500.18 m deep drillhole with a diameter of 75.7 mm at Olkiluoto in July - August 2010. The identification number of the drillhole is OL-KR54. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the returning and drilling water were recorded. The drill rig was computer controlled and the computer recorded drilling parameters during drilling. The objective of the measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volume of the used drilling, washing and flushing water was 382 m 3 . The measured volume of the returning water in the drillhole was 334 m 3 . The deviation of the drillhole was measured with the deviation measuring instruments EMS and Gyro. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive strength was 111.5 MPa, the average Young's Modulus was 43.7 GPa and the average Poisson's ratio was 0.17. The main rock types are diatexitic and veined gneisses, pegmatitic granite and mafic gneiss. The average fracture frequency is 1.6 pcs/m and the average RQD value is 97.6 %. Nine fractured zones were penetrated by the drillhole. (orig.)

  3. An assessment of the effect on Olkiluoto repository capacity achievable with advanced fuel cycles

    Energy Technology Data Exchange (ETDEWEB)

    Juutilainen, P.; Viitanen, T. [VTT Technical Research Centre of Finland, P.O. Box 1000, FI-02044 VTT (Finland)

    2013-07-01

    Previously a few scenarios have been simulated for transition from thermal to fast reactor fleet in Finland in order to determine how much the transuranic inventory could be reduced with the partitioning and transmutation (P-T) technologies. Those calculations, performed with COSI6 code developed by CEA, are extended in the present study, in which the effect of P-T on the capacity of the planned final disposal repository at Olkiluoto (Finland) is evaluated by taking into account the created fission products and transuranic residuals from the reprocessing operations. The decay heat is assumed to be the most restrictive factor in defining the waste disposal packing density. The repository capacity evaluation of this study is based on the comparison of the decay heats produced by the deposited waste in various scenarios. The reference scenario of this article involves only Light Water Reactors (LWR) in an open fuel cycle. The capacity requirement of the geological repository is estimated in a few closed fuel cycle scenarios, all including actinide transmutation with Fast Reactors (FR). The comparison between the P-T scenarios and reference is based on the decay heat production of the deposited waste. The COSI6 code is used for simulations to provide the repository decay heat curves. Applying the closed fuel cycle would change the disposal concept and schedule, because of which it is not quite straightforward to assess the impact of P-T on the capacity. However, it can be concluded that recycling the transuranic nuclides probably decreases the required volume for the disposal, but thermal dimensioning analysis is needed for more specific conclusions.

  4. Electromagnetic SAMPO monitoring soundings at OLKILUOTO in 2012 with updated interpretations

    International Nuclear Information System (INIS)

    Korhonen, K.

    2013-11-01

    The Geological Survey of Finland (GTK) has carried out electromagnetic depth soundings annually at fixed stations at Olkiluoto since 2004 as part of a monitoring programme. The goal of the programme is to detect and monitor changes in the electrical properties of the bedrock above and in the vicinity of the ONKALO tunnel which will serve as a part of the future underground nuclear waste disposal facility. A new Sampo monitoring survey was carried out during October 2012. The survey plan of 2011 was slightly modified and 36 soundings at 16 measurement stations were carried out. The nominal coil separations of 200, 400, 500, 600 and 800 meters were used. Interpretations at eight selected stations were updated with the new data. The interpretations indicate consistent statistically significant changes. Annual increases in resistivity were detected at stations to the East of ONKALO while annual decreases in resistivity were detected to the West of ONKALO. However, these changes need to be considered keeping in mind the high degree of uncertainty associated with the data and their interpretations. (orig.)

  5. Elecromagnetic Sampo monitoring soundings at Olkiluoto in 2013 with updated interpretations

    International Nuclear Information System (INIS)

    Korhonen, K.

    2014-10-01

    The Geological Survey of Finland (GTK) has carried out electromagnetic depth soundings annually at fixed stations in Olkiluoto since 2004 as part of a monitoring program. The goal of the monitoring program is to detect and monitor changes in the electrical properties of the bedrock in the vicinity of the ONKALO underground research facility which will constitute a part of the final nuclear waste repository. A new Sampo monitoring survey was carried out by GTK in October 2013. The survey consists of 37 soundings performed at 17 measurement stations. The nominal coil separations of 200, 400, 500, 600 and 800 metres were used depending on the station. Layer-model interpretations of soundings at eight selected stations were updated with the new data. The interpretations indicate consistent annual changes. Resistivities be-low stations to the East of the ONKALO facility appear to increase annually. In contrast, resistivities below stations to the West of the ONKALO facility appear to decrease annually. However, these changes need to be considered keeping in mind the uncertainties associated with the data and their interpretations. (orig.)

  6. Sampling and characterisation of groundwater colloids in ONKALO at Olkiluoto, Finland, 2011

    Energy Technology Data Exchange (ETDEWEB)

    Takala, M.; Ojala, S.; Jarvinen, E.; Manninen, P. [Ramboll Finland Oy, Espoo (Finland)

    2012-11-15

    The purpose of this study was to estimate the concentration of colloids and composition of the colloid phase on the basis of the water chemistry results of filtered and unfiltered water samples and to compare the results with the previous ones. The water samples were collected from groundwater stations ONK-PVA1 and ONK-PVA3 in October 2011. The colloid concentrations were determined from scanning electron microscopy (SEM) micrographs taken from the filters. The change in the water chemistry due to filtration was also analysed. The decrease of element concentrations due to filtration would possibly reflect the composition of the colloid phase. Because the concentration of the colloids is very low, two parallel water samples were analysed five times with an Inductively Coupled Plasma - Mass Spectrometry (ICP-MS) analyser so that the chemical differences between the filtered and unfiltered water could be evaluated. The colloid concentration in ONK-PVA1, determined by the single particle analysis of SEM micrographs, was 6 {mu}g/l while the colloid concentration in ONK-PVA3 was 7 {mu}g/l. The colloid phase composition could not be reliably determined due to the low colloid concentration. (orig.)

  7. Sampling and characterisation of groundwater colloids in ONKALO at Olkiluoto, Finland 2009-2010

    International Nuclear Information System (INIS)

    Jaervinen, E.; Manninen, P.; Takala, M.; Vilhunen, S.

    2011-04-01

    The purpose of this study was to estimate the concentration of colloids and composition of the colloid phase on the basis of the water chemistry results of filtered and unfiltered water samples and to compare the results with the previous ones. The water samples were collected from groundwater stations ONK-PVA1 in December 2009 and ONKPVA5 in June 2010. The colloid concentrations were determined from scanning electron microscopy (SEM) micrographs taken from the filters. The change in the water chemistry due to filtration was also analysed. The decrease of element concentrations due to filtration would possibly reflect the composition of the colloid phase. Because the concentration of the colloids is very low, three parallel water samples were analysed three times with an Inductively Coupled Plasma - Mass Spectrometry (ICP-MS) analyser so that the chemical differences between the filtered and unfiltered water could be evaluated. The colloid concentration in ONK-PVA1, determined by the single particle analysis of SEM micrographs, was 0.5 μg/l while the colloid concentration in ONK-PVA5 was 0.15 μg/l. The colloid phase composition could not be reliably determined due to the low colloid concentration. (orig.)

  8. GPS operations at Olkiluoto, Kivetty and Romuvaara in 2008

    International Nuclear Information System (INIS)

    Kallio, U.; Ahola, J.; Koivula, H.; Jokela, J.; Poutanen, M.

    2009-09-01

    The GPS based deformation studies have been made at the investigation areas of Posiva since 1995, when the network of ten GPS pillars was established at Olkiluoto. The network of seven GPS pillars was built at Kivetty and Romuvaara during the year 1996. One pillar in each investigation area belongs to the Finnish permanent GPS network, FinnRef. A total of 26 GPS measurement campaigns have been carried out at Olkiluoto since 1995, and 17 campaigns at Kivetty and Romuvaara. According to the time series of the GPS results 1/3 of the baselines at Olkiluoto have statistically significant change rates. However, the observed movements are smaller than 0.20 mm/a. The networks of Kivetty and Romuvaara are quite stable expect one pillar at Romuvaara. There are seven pillars, which have statistically significant horizontal velocities at Olkiluoto. These local velocity components are small but taking into account the standard deviations the largest velocity components seems to be reliably determined. The uniform scale for the GPS measurements made in different years is the basic condition for reliable results in the deformation analyses. At Olkiluoto a baseline for electronic distance measurements (EDM) was built in 2002. The baseline has been measured using EDM instruments in connection to the GPS observations. The comparison between the GPS and EDM results can help to fix a possible scale error of the GPS measurements. The GPS network at Olkiluoto was extended in 2003. The new pillars were built close to Kuivalahti village and on a small island of Iso Pyrekari. According to the geological evidence it is expected that a fracture zone is located between the new stations, thus enabling the determination of possible deformations along the fracture zone. The new pillars have been observed since 2003 and now we have computed the first deformation analysis from the six years data. The local crustal deformations have been studied in GeoSatakunta project, too. This GPS network is

  9. GPS operations at Olkiluoto, Kivetty and Romuvaara in 2007

    International Nuclear Information System (INIS)

    Ahola, J.; Koivula, H.; Jokela, J.

    2008-05-01

    The GPS based deformation studies have been made at the investigation areas of Posiva since 1995, when the network of ten GPS pillars was established at Olkiluoto. The network of seven GPS pillars was built at Kivetty and Romuvaara during the year 1996. One pillar in each investigation area belongs to the Finnish permanent GPS network, FinnRef. 24 GPS measurement campaigns have been carried out at Olkiluoto since 1995, and 16 campaigns at Kivetty and Romuvaara. According to the time series of the GPS results 1/3 of the baselines at Olkiluoto have statistically significant change rates. However, the observed movements are smaller than ± 0.20 mm/a. The networks of Kivetty and Romuvaara are quite stabile expect one pillar at Romuvaara. There are five pillars, which have statistically significant horizontal velocities at Olkiluoto. These local velocity components are small but taking into account the standard deviations the largest velocity components seems to be reliably determined (maximum velocity is -0.22 mm/a ± 0.02 mm/a). The uniform scale for the GPS measurements made in different years is the basic condition for reliable results in the deformation analyses. At Olkiluoto a baseline for electronic distance measurements (EDM) was built in 2002. The baseline has been measured using EDM instruments simultaneously with the GPS observations. The comparison between the GPS and EDM results can solve a possible scale error of the GPS. The GPS network at Olkiluoto was extended in 2003. The new pillars were built close to Kuivalahti village and on a small island of Iso Pyrekari. According to the geological evidence it is expected that a fracture zone is located between the new stations, thus enabling the determination of possible deformations along the fracture zone. The new pillars have been observed since 2003, but the time series are still too short for reliable deformation studies. The local crustal deformations have been studied in GeoSatakunta project, too. This

  10. Results of Monitoring at Olkiluoto in 2007. Rock Mechanics

    International Nuclear Information System (INIS)

    Mattila, J.; Hakala, M.

    2008-06-01

    Posiva Oy has operated a local microseismic at Olkiluoto network since February 2002. During the monitoring in 2007, altogether 2207 events have been located in the Olkiluoto area, in the reported time period. The magnitudes of the observed events range from ML = -2.1 to 1.5 (ML = magnitude in local Richter's scale). All these events are explosions. Evidence of seismic activity that would have influence on the safety of the ONKALO, have not been observed. One recorded event was a microearthquake of magnitude ML 1.9, which occurred in Laitila, approximately 40 km from Olkiluoto. The GPS based deformation studies have been made at the investigation areas of Posiva since 1995, when the network of ten GPS pillars was established at Olkiluoto. Since then, altogether 24 GPS measurement campaigns have been carried out at Olkiluoto. According to the time series of the GPS results, 1/3 of the baselines at Olkiluoto have statistically significant change rates. However, the observed movements are smaller than ± 0.20 mm/a. There are five pillars, which have statistically significant horizontal velocities at Olkiluoto. These local velocity components are small but taking into account the standard deviations the largest velocity components seems to be reliably determined (maximum velocity is -0.21 mm/a ± 0.02 mm/a) In order to monitor vertical movements at Olkiluoto, precise leveling campaigns of the GPS stations were started in the area in autumn 2003. Since then, leveling campaigns have taken place in 2005 and 2007, including the leveling of the existing GPS network and line from Olkiluoto Island to Lapijoki at the main land. Additional smaller leveling campaigns took place in 2006. The campaign in autumn 2007 consisted of the levellings of all measured and undestroyed points of the earlier campaigns. Compared to the mean theoretical land uplift, the nodal bench mark near the crossing of Olkiluodontie and Satamatie had risen in four years 2.6 mm more than the nodal bench

  11. Solar power in Finland

    International Nuclear Information System (INIS)

    Vesa, A.M.

    2004-01-01

    Solar cells, or photovoltaic units, have provided a useful supply of energy for low-power, non-gridconnected applications in Finland for some years. Applications have included navigational buoys, base stations for mobile phone networks, and appliances in holiday homes. Solar-powered systems have also been used in connection with grid power for over a decade, in Finland and elsewhere, and have proved generally successful - and solar energy is emerging as an increasingly interesting alternative for distributed electricity generation

  12. Olkiluoto surface hydrological modelling: Update 2012 including salt transport modelling

    International Nuclear Information System (INIS)

    Karvonen, T.

    2013-11-01

    Posiva Oy is responsible for implementing a final disposal program for spent nuclear fuel of its owners Teollisuuden Voima Oyj and Fortum Power and Heat Oy. The spent nuclear fuel is planned to be disposed at a depth of about 400-450 meters in the crystalline bedrock at the Olkiluoto site. Leakages located at or close to spent fuel repository may give rise to the upconing of deep highly saline groundwater and this is a concern with regard to the performance of the tunnel backfill material after the closure of the tunnels. Therefore a salt transport sub-model was added to the Olkiluoto surface hydrological model (SHYD). The other improvements include update of the particle tracking algorithm and possibility to estimate the influence of open drillholes in a case where overpressure in inflatable packers decreases causing a hydraulic short-circuit between hydrogeological zones HZ19 and HZ20 along the drillhole. Four new hydrogeological zones HZ056, HZ146, BFZ100 and HZ039 were added to the model. In addition, zones HZ20A and HZ20B intersect with each other in the new structure model, which influences salinity upconing caused by leakages in shafts. The aim of the modelling of long-term influence of ONKALO, shafts and repository tunnels provide computational results that can be used to suggest limits for allowed leakages. The model input data included all the existing leakages into ONKALO (35-38 l/min) and shafts in the present day conditions. The influence of shafts was computed using eight different values for total shaft leakage: 5, 11, 20, 30, 40, 50, 60 and 70 l/min. The selection of the leakage criteria for shafts was influenced by the fact that upconing of saline water increases TDS-values close to the repository areas although HZ20B does not intersect any deposition tunnels. The total limit for all leakages was suggested to be 120 l/min. The limit for HZ20 zones was proposed to be 40 l/min: about 5 l/min the present day leakages to access tunnel, 25 l/min from

  13. Olkiluoto surface hydrological modelling: Update 2012 including salt transport modelling

    Energy Technology Data Exchange (ETDEWEB)

    Karvonen, T. [WaterHope, Helsinki (Finland)

    2013-11-15

    Posiva Oy is responsible for implementing a final disposal program for spent nuclear fuel of its owners Teollisuuden Voima Oyj and Fortum Power and Heat Oy. The spent nuclear fuel is planned to be disposed at a depth of about 400-450 meters in the crystalline bedrock at the Olkiluoto site. Leakages located at or close to spent fuel repository may give rise to the upconing of deep highly saline groundwater and this is a concern with regard to the performance of the tunnel backfill material after the closure of the tunnels. Therefore a salt transport sub-model was added to the Olkiluoto surface hydrological model (SHYD). The other improvements include update of the particle tracking algorithm and possibility to estimate the influence of open drillholes in a case where overpressure in inflatable packers decreases causing a hydraulic short-circuit between hydrogeological zones HZ19 and HZ20 along the drillhole. Four new hydrogeological zones HZ056, HZ146, BFZ100 and HZ039 were added to the model. In addition, zones HZ20A and HZ20B intersect with each other in the new structure model, which influences salinity upconing caused by leakages in shafts. The aim of the modelling of long-term influence of ONKALO, shafts and repository tunnels provide computational results that can be used to suggest limits for allowed leakages. The model input data included all the existing leakages into ONKALO (35-38 l/min) and shafts in the present day conditions. The influence of shafts was computed using eight different values for total shaft leakage: 5, 11, 20, 30, 40, 50, 60 and 70 l/min. The selection of the leakage criteria for shafts was influenced by the fact that upconing of saline water increases TDS-values close to the repository areas although HZ20B does not intersect any deposition tunnels. The total limit for all leakages was suggested to be 120 l/min. The limit for HZ20 zones was proposed to be 40 l/min: about 5 l/min the present day leakages to access tunnel, 25 l/min from

  14. Licensing and supervision of nuclear facilities in Finland; Genehmigung und Aufsicht von nuklearen Anlagen in Finnland

    Energy Technology Data Exchange (ETDEWEB)

    Laaksonen, J. [Finnish Centre for Radiation and Nuclear Safety (STUK), Helsinki (Finland)

    2005-07-01

    STUK is the independent nuclear supervisory agency in Finland with administrative powers; its staff has the technical and scientific competence required for safety assessments and for supervision. STUK operates under the supervision of the Ministry for Social Affairs and Health which, to demonstrate its independence, has no duties in the energy sector and, in addition, supervises STUK in administrative matters, not in scientific and technical decisions. Internal rules of STUK ensure neutrality also of its staff in matters of energy policy. The activities of STUK as a supervisory and licensing authority in Finland are described in detail for the management of spent nuclear fuel and the new Olkiluoto 3 nuclear power plant currently under construction. (orig./GL)

  15. Results of monitoring at Olkiluoto in 2006. Rock mechanics

    International Nuclear Information System (INIS)

    Mattila, J.

    2007-07-01

    Posiva Oy has operated a local microseismic at Olkiluto network since February 2002. During the monitoring in 2006, altogether 2041 events have been located in the Olkiluoto area, in the reported time period. The magnitudes of the observed events range from ML = -1.1 to 3.1 (ML = magnitude in local Richter's scale). Most of the events are construction-related explosions but two of them are recorded as microearthquakes. Evidence of seismic activity that would have influence on the safety of the ONKALO, have not been observed. The observed earthquakes that occurred in 2006 were small, with a magnitude of ML -0.6 and ML= -0.9. The earthquakes relate to small movements in brittle deformation zones OL-BFZ043 and OL-BFZ034. Estimated peak slip values of the earthquakes are 14 μm and 4 μm and the source radiuses 11 and 8 meters, respectively. The GPS based deformation studies have been made at the investigation areas of Posiva since 1995, when the network of ten GPS pillars was established at Olkiluoto. Since then, altogether 22 GPS measurement campaigns have been carried out at Olkiluoto. According to the time series of the GPS results, 1/3 of the baselines at Olkiluoto have statistically significant change rates. However, the observed movements are smaller than ± 0.22 mm/a. There are five pillars, which have statistically significant horizontal velocities at Olkiluoto. These local velocity components are small but taking into account the standard deviations the largest velocity components seems to be reliably determined (maximum velocity is -0.23 mm/a ± 0.023 mm/a) (orig.)

  16. The satellite symposium of the 2nd COE-INES international symposium, INES-2 on 'final disposal sites: How were they determined?'

    International Nuclear Information System (INIS)

    2007-03-01

    The symposium was organized on December 1, 2006, by Tokyo Institute of Technology in charge of the 21st century COE program to establish innovative nuclear energy systems for sustainable development of the world. It was aimed at finding the process of determining the final radioactive waste disposal sites of Japan through a comprehensive and interdisciplinary approach. Four guests, 2 from Finland and 2 from Korea each one from the promoting side and the other from the local governmental side, were invited from the two countries that have already determined the sites through the necessary processes to find the consensus. Participants were 103 including 7 from abroad. The symposium consisted of plenary lectures: Regulators' Role in Development of Finnish Nuclear Waste Disposal Program, and A Successful Case Site Selection for Low- and Intermediate-Level Radioactive Waste Disposal Facility, Site Selection for LILW Disposal Facility in Korea, Public Participations in the Selection and Acceptance of Olkiluoto Site for the Final Disposal of Spent Nuclear Fuel in Finland and, continuously, a panel discussion to find what are the key problems in solving the final disposal site selection in Japan and what will play a major role towards the solution of this important issues. The report includes all the lectures with diagrams and the records of questions and answers. (S. Ohno)

  17. Permanent vegetation quadrats on Olkiluoto island. Establishment and results from the first inventory

    Energy Technology Data Exchange (ETDEWEB)

    Huhta, A.P.; Korpela, L. [Finnish Forest Research Institute, Helsinki (Finland)

    2006-05-15

    This report describes in detail the vegetation quadrats established inside the permanent, follow-up sample plots (Forest Extensive High-level monitoring plots, FEH) on Olkiluoto Island. During summer 2005 a total of 94 sample plots (a 30 m{sup 2}), each containing eight quadrats (a 1m{sup 2}), were investigated. The total number of sampled quadrats was 752. Seventy of the 94 plots represent coniferous stands: 57 Norway spruce-dominated and 13 Scots pine-dominated stands. Ten of the plots represent deciduous, birch-dominated (Betula spp.) stands, 7 plots common alder-dominated (Alnus glutinosa) stands, and seven plots are mires. The majority of the coniferous tree stands were growing on sites representing various succession stages of the Myrtillus, Vaccinium-Myrtillus and Deschampsia-Myrtillus forest site types. The pine-dominated stands growing on exposed bedrock clearly differed from the other coniferous stands: the vegetation was characterised by the Cladina, Calluna-Cladina and Empetrum-Vaccinium vitis-idaea/Vaccinium Myrtillus forest site types. The deciduous stands were characterized by tall grasses, especially Calamagrostis epigejos, C. purpurea and Deschampsia flexuosa. The vegetation of the deciduous stands dominated by common alder represented grove-like sites and seashore groves. Typical species for mires included Calamagrostis purpurea, Calla palustris, Equisetum sylvaticum, and especially white mosses (Sphagnum spp.). A total of 184 vascular plant species were found growing within the quadrats. Due to the high number of quadrats in these forests, the spruce stands had the highest total number of species, but the birch and alder-dominated forests had the highest average number of species per quadrat. This basic inventory of the permanent vegetation quadrats on Olkiluoto Island provides a sound starting point for future vegetation surveys. Guidelines for future inventories and supplementary sampling are given in the discussion part of this report. (orig.)

  18. Permanent vegetation quadrats on Olkiluoto island. Establishment and results from the first inventory

    International Nuclear Information System (INIS)

    Huhta, A.P.; Korpela, L.

    2006-05-01

    This report describes in detail the vegetation quadrats established inside the permanent, follow-up sample plots (Forest Extensive High-level monitoring plots, FEH) on Olkiluoto Island. During summer 2005 a total of 94 sample plots (a 30 m 2 ), each containing eight quadrats (a 1m 2 ), were investigated. The total number of sampled quadrats was 752. Seventy of the 94 plots represent coniferous stands: 57 Norway spruce-dominated and 13 Scots pine-dominated stands. Ten of the plots represent deciduous, birch-dominated (Betula spp.) stands, 7 plots common alder-dominated (Alnus glutinosa) stands, and seven plots are mires. The majority of the coniferous tree stands were growing on sites representing various succession stages of the Myrtillus, Vaccinium-Myrtillus and Deschampsia-Myrtillus forest site types. The pine-dominated stands growing on exposed bedrock clearly differed from the other coniferous stands: the vegetation was characterised by the Cladina, Calluna-Cladina and Empetrum-Vaccinium vitis-idaea/Vaccinium Myrtillus forest site types. The deciduous stands were characterized by tall grasses, especially Calamagrostis epigejos, C. purpurea and Deschampsia flexuosa. The vegetation of the deciduous stands dominated by common alder represented grove-like sites and seashore groves. Typical species for mires included Calamagrostis purpurea, Calla palustris, Equisetum sylvaticum, and especially white mosses (Sphagnum spp.). A total of 184 vascular plant species were found growing within the quadrats. Due to the high number of quadrats in these forests, the spruce stands had the highest total number of species, but the birch and alder-dominated forests had the highest average number of species per quadrat. This basic inventory of the permanent vegetation quadrats on Olkiluoto Island provides a sound starting point for future vegetation surveys. Guidelines for future inventories and supplementary sampling are given in the discussion part of this report. (orig.)

  19. Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Evolution report

    International Nuclear Information System (INIS)

    Smith, P.; Johnson, L.; Snellman, M.; Pastina, B.; Gribi, P.

    2007-12-01

    The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. KBS-3H and KBS-3V are the two design alternatives of the KBS-3 method. Posiva and SKB have conducted a joint research, demonstration and development (RD and D) programme in 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The overall objectives of the present phase covering the period 2004-2007, have been to demonstrate that the horizontal deposition alternative is technically feasible and to demonstrate that it fulfils the same long-term safety requirements as KBS-3V. The safety studies conducted as part of this programme include a safety assessment of a preliminary design of a KBS-3H repository for spent nuclear fuel located about 400 m underground at the Olkiluoto site, which is the proposed site for a spent fuel repository in Finland. In the KBS-3H design alternative, each canister, with a surrounding layer of bentonite clay, is pre-packaged in a perforated steel cylinder prior to emplacement in the deposition drift; the entire assembly is called the supercontainer. Several supercontainers are positioned along parallel, 100 - 300 m long deposition drifts, which are sealed following waste emplacement using drift end plugs. Bentonite distance blocks separate the supercontainers, one from another, along the drift. Steel compartment plugs can be used to seal off drift sections with higher inflow, thus isolating the different compartments within the drift. The present report describes the repository evolution in successive time frames, including key uncertainties. The description of evolution starts with the initial conditions at the time of emplacement of the first canisters. The repository evolves through an early, transient phase to a state where evolution is far slower. Particular attention is given to describing the transient phase, since this is where most of the

  20. Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Process report

    International Nuclear Information System (INIS)

    Gribi, Peter; Johnson, Lawrence; Suter, Daniel; Smith, Paul; Pastina, Barbara; Snellman, Margit

    2008-01-01

    The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. KBS-3H and KBS-3V are the two design alternatives of the KBS-3 spent fuel disposal method. Posiva and SKB have conducted a joint research, demonstration and development (RDandD) programme in 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The overall objectives of the present phase covering the period 2004-2007 have been to demonstrate that the horizontal deposition alternative is technically feasible and to demonstrate that it fulfils the same long-term safety requirements as KBS-3V. The safety studies conducted as part of this programme include a safety assessment of a preliminary design of a KBS-3H repository for spent nuclear fuel located about 400 m underground at the Olkiluoto site, which is the proposed site for a spent fuel repository in Finland. In the KBS-3H design alternative, each canister, with a surrounding layer of bentonite clay, is placed in a perforated steel cylinder prior to emplacement; the entire assembly is called the supercontainer. Several supercontainers are positioned along parallel, 100-300 m long deposition drifts, which are sealed following waste emplacement using drift end plugs. Bentonite distance blocks separate the supercontainers, one from another, along the drift. Steel compartment plugs can be used to seal off drift sections with higher inflow, thus isolating the different compartments within the drift. The present report describes the main processes potentially affecting the long-term safety of the system, covering radiation-related, thermal, hydraulic, mechanical, chemical (including microbiological) and radionuclide transport-related processes. The process descriptions deal sequentially with the main sub-systems: fuel/cavity in canister, cast iron insert and copper canister, buffer and other bentonite components, supercontainer

  1. Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Process report

    Energy Technology Data Exchange (ETDEWEB)

    Gribi, Peter; Johnson, Lawrence; Suter, Daniel; Smith, Paul; Pastina, Barbara; Snellman, Margit

    2008-01-15

    The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. KBS-3H and KBS-3V are the two design alternatives of the KBS-3 spent fuel disposal method. Posiva and SKB have conducted a joint research, demonstration and development (RDandD) programme in 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The overall objectives of the present phase covering the period 2004-2007 have been to demonstrate that the horizontal deposition alternative is technically feasible and to demonstrate that it fulfils the same long-term safety requirements as KBS-3V. The safety studies conducted as part of this programme include a safety assessment of a preliminary design of a KBS-3H repository for spent nuclear fuel located about 400 m underground at the Olkiluoto site, which is the proposed site for a spent fuel repository in Finland. In the KBS-3H design alternative, each canister, with a surrounding layer of bentonite clay, is placed in a perforated steel cylinder prior to emplacement; the entire assembly is called the supercontainer. Several supercontainers are positioned along parallel, 100-300 m long deposition drifts, which are sealed following waste emplacement using drift end plugs. Bentonite distance blocks separate the supercontainers, one from another, along the drift. Steel compartment plugs can be used to seal off drift sections with higher inflow, thus isolating the different compartments within the drift. The present report describes the main processes potentially affecting the long-term safety of the system, covering radiation-related, thermal, hydraulic, mechanical, chemical (including microbiological) and radionuclide transport-related processes. The process descriptions deal sequentially with the main sub-systems: fuel/cavity in canister, cast iron insert and copper canister, buffer and other bentonite components, supercontainer

  2. Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Evolution report

    International Nuclear Information System (INIS)

    Smith, Paul; Johnson, Lawrence; Snellman, Margit; Pastina, Barbara; Gribi, Peter

    2008-01-01

    The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. KBS-3H and KBS-3V are the two design alternatives of the KBS-3 method. Posiva and SKB have conducted a joint research, demonstration and development (RDandD) programme in 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The overall objectives of the present phase covering the period 2004-2007, have been to demonstrate that the horizontal deposition alternative is technically feasible and to demonstrate that it fulfils the same long-term safety requirements as KBS-3V. The safety studies conducted as part of this programme include a safety assessment of a preliminary design of a KBS-3H repository for spent nuclear fuel located about 400 m underground at the Olkiluoto site, which is the proposed site for a spent fuel repository in Finland. In the KBS-3H design alternative, each canister, with a surrounding layer of bentonite clay, is pre-packaged in a perforated steel cylinder prior to emplacement in the deposition drift; the entire assembly is called the supercontainer. Several supercontainers are positioned along parallel, 100-300 m long deposition drifts, which are sealed following waste emplacement using drift end plugs. Bentonite distance blocks separate the supercontainers, one from another, along the drift. Steel compartment plugs can be used to seal off drift sections with higher inflow, thus isolating the different compartments within the drift. The present report describes the repository evolution in successive time frames, including key uncertainties. The description of evolution starts with the initial conditions at the time of emplacement of the first canisters. The repository evolves through an early, transient phase to a state where evolution is far slower. Particular attention is given to describing the transient phase, since this is where most of the

  3. Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Evolution report

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Paul; Johnson, Lawrence; Snellman, Margit; Pastina, Barbara; Gribi, Peter

    2008-01-15

    The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. KBS-3H and KBS-3V are the two design alternatives of the KBS-3 method. Posiva and SKB have conducted a joint research, demonstration and development (RDandD) programme in 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The overall objectives of the present phase covering the period 2004-2007, have been to demonstrate that the horizontal deposition alternative is technically feasible and to demonstrate that it fulfils the same long-term safety requirements as KBS-3V. The safety studies conducted as part of this programme include a safety assessment of a preliminary design of a KBS-3H repository for spent nuclear fuel located about 400 m underground at the Olkiluoto site, which is the proposed site for a spent fuel repository in Finland. In the KBS-3H design alternative, each canister, with a surrounding layer of bentonite clay, is pre-packaged in a perforated steel cylinder prior to emplacement in the deposition drift; the entire assembly is called the supercontainer. Several supercontainers are positioned along parallel, 100-300 m long deposition drifts, which are sealed following waste emplacement using drift end plugs. Bentonite distance blocks separate the supercontainers, one from another, along the drift. Steel compartment plugs can be used to seal off drift sections with higher inflow, thus isolating the different compartments within the drift. The present report describes the repository evolution in successive time frames, including key uncertainties. The description of evolution starts with the initial conditions at the time of emplacement of the first canisters. The repository evolves through an early, transient phase to a state where evolution is far slower. Particular attention is given to describing the transient phase, since this is where most of the

  4. Estimating the mechanical properties of the brittle deformation zones at Olkiluoto

    International Nuclear Information System (INIS)

    Hudson, J.A.; Cosgrove, J.W.; Johansson, E.

    2008-09-01

    In rock mechanics modelling to support repository design and safety assessment for the Olkiluoto site, it is necessary to obtain the relevant rock mechanics parameters, these being an essential pre-requisite for the modelling. The parameters include the rock stress state, the properties of the intact rock and the rock mass, and the properties of the brittle deformation zones which represent major discontinuities in the rock mass continuum. However, because of the size and irregularity of the brittle deformation zones, it is not easy to estimate their mechanical properties, i.e. their deformation and strength properties. Following Section 1 explaining the motivation for the work and the objective of the Report, in Sections 2 and 3, the types of fractures and brittle deformation zones that can be encountered are described with an indication of the mechanisms that lead to complex structures. The geology at Olkiluoto is then summarized in Section 4 within the context of this Report. The practical aspects of encountering the brittle deformation zones in outcrops, drillholes and excavations are described in Sections 5 and 6 with illustrative examples of drillhole core intersections in Section 7. The various theoretical, numerical and practical methods for estimating the mechanical properties of the brittle deformation zones are described in Section 8, together with a Table summarizing each method's advantages, disadvantages and utility in estimating the mechanical properties of the zones. We emphasise that the optimal approach to estimating the mechanical properties of the brittle deformation zones cannot be determined without a good knowledge, not only of each estimation method's capabilities and idiosyncrasies, but also of the structural geology background and the specific nature of the brittle deformation zones being characterized. Finally, in Section 9, a Table is presented outlining each method's applicability to the Olkiluoto site. A flowchart is included to

  5. Results of Monitoring at Olkiluoto in 2005. Rock Mechanics

    International Nuclear Information System (INIS)

    Riikonen, S.

    2006-08-01

    Programme of Monitoring (Posiva 2003 b) was introduced to study Olkiluoto investigation are both during and following the excavation of underground test facility, ONKALO. Programme consists of four main headings: rock mechanics, hydrology and hydrogeology, geochemistry and other types of disturbance. Monitoring programme in year 2005 consist of three fields of research: microseismic measurements, GPS measurements and precise levelling. This report presents Posiva's rock mechanical monitoring programme results from the year 2005. Report has been composed from annual reports of microseismic measurements, GPS measurements and precise levelling by Sanna Riikonen. In Olkiluoto, Posiva Oy has operated a local seismic network since February 2002. This report gives the results of microseismic monitoring during the year 2005. Also the changes in the structure and the operation procedure of the network are described. The network has operated nearly continuously. The total duration of network failures has been about 8 hours. Altogether 2159 events have been located in the Olkiluoto area, in reported time period. The magnitudes of the observed events range from ML = -2.1to ML = 1.6 (ML = magnitude in local Richter's scale). Most of them are explosions. Three of the observed events are be classified as microearthquakes. Evidence of activity that would has influence on the safety of the ONKALO, have not found. The GPS based deformation studies has been made at the investigation areas of Posiva since 1995, when the network of ten GPS pillars was established at Olkiluoto. Twenty GPS measurement campaigns have been carried out at Olkiluoto since 1995. According to the time series of the GPS results 1/3 of the baselines at Olkiluoto have statistically significant change rates. However, the observed movements are smaller than ± 0.22 mm/a. There are five pillars, which have statistically significant horizontal velocities at Olkiluoto. The local velocity components are small but

  6. Geophysical borehole logging of the boreholes KR23 extension, KR29 and KR29b at Olkiluoto 2004

    International Nuclear Information System (INIS)

    Lahti, M.; Heikkinen, E.

    2005-04-01

    Suomen Malmi Oy conducted geophysical borehole logging of the boreholes KR23 extension, KR25b, KR29 and KR29b at the Olkiluoto site in Eurajoki during October 2004. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and processing of the acoustic data. The report describes the field operation, equipment as well as processing procedures and shows the obtained results and their quality in the appendices. The raw and processed data are delivered digitally in WellCAD and Excel format. (orig.)

  7. Geophysical borehole logging of the boreholes KR23 extension, KR29 and KR29b at Olkiluoto 2004

    Energy Technology Data Exchange (ETDEWEB)

    Lahti, M. [Suomen Malmi Oy, Espoo (Finland); Heikkinen, E. [JP-Fintact Oy, Vantaa (Finland)

    2005-04-15

    Suomen Malmi Oy conducted geophysical borehole logging of the boreholes KR23 extension, KR25b, KR29 and KR29b at the Olkiluoto site in Eurajoki during October 2004. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and processing of the acoustic data. The report describes the field operation, equipment as well as processing procedures and shows the obtained results and their quality in the appendices. The raw and processed data are delivered digitally in WellCAD and Excel format. (orig.)

  8. Geophysical borehole logging of the boreholes KR37, KR37B and KR38, at Olkiluoto 2005

    International Nuclear Information System (INIS)

    Majapuro, J.

    2006-03-01

    Suomen Malmi Oy conducted geophysical borehole logging of the boreholes KR37, KR37b and KR38 at the Olkiluoto site in Eurajoki during September and October 2005. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and processing of the acoustic data. The report describes the field operation, equipment as well as processing procedures and shows the obtained results and their quality in the appendices. The raw and processed data are delivered digitally in WellCAD and Excel format. (orig.)

  9. Basic rocks in Finland

    International Nuclear Information System (INIS)

    Piirainen, T.; Gehoer, S.; Iljina, M.; Kaerki, A.; Paakkola, J.; Vuollo, J.

    1992-10-01

    Basic igneous rocks, containing less than 52% SiO 2 , constitute an important part of the Finnish Archaean and Proterozoic crust. In the Archaean crust exist two units which contain the majority of the basic rocks. The Arcaean basic rocks are metavolcanics and situated in the Greenstone Belts of Eastern Finland. They are divided into two units. The greenstones of the lower one are tholeiites, komatiites and basaltic komatiites. The upper consists of bimodal series of volcanics and the basic rocks of which are Fe-tholeiites, basaltic komatiites and komatiites. Proterozoic basic rocks are divided into seven groups according to their ages. The Proterozoic igneous activity started by the volominous basic magmatism 2.44 Ga ago. During this stage formed the layered intrusions and related dykes in the Northern Finland. 2.2 Ga old basic rocks are situated at the margins of Karelian formations. 2.1 Ga aged Fe-tholeiitic magmatic activity is widespread in Eastern and Northern Finland. The basic rocks of 1.97 Ga age group are met within the Karelian Schist Belts as obducted ophiolite complexes but they occur also as tholeiitic diabase dykes cutting the Karelian schists and Archean basement. The intrusions and the volcanics of the 1.9 Ga old basic igneous activity are mostly encountered around the Granitoid Complex of Central Finland. Subjotnian, 1.6 Ga aged tholeiitic diabases are situated around the Rapakivi massifs of Southern Finland, and postjotnian, 1.2 Ga diabases in Western Finland where they form dykes cutting Svecofennian rocks

  10. Gift from Finland

    International Nuclear Information System (INIS)

    1964-01-01

    An instrument worth $19 000 for the analysis of nuclear radiation, donated by Finland to IAEA, was handed over by the Finnish Ambassador, Mr. Otso Wartiovaara, to the Director General of IAEA, Dr. Sigvard Eklund, at the Agency's laboratory at Seibersdorf on 22 January. The instrument, a multi-channel analyzer with 512 channels, was constructed in Finland. It is being used in connection with all the major Agency projects under way at Seibersdorf, such as the standardization of radionuclides, agricultural research, and analytical work carried out at the request of Member States

  11. Assessment of doses to non-human biota: Review of developments and demonstration assessment for Olkiluoto repository

    International Nuclear Information System (INIS)

    Smith, K.; Robinson, C.

    2006-12-01

    This report provides a summary of work commissioned by Posiva Oy and undertaken by Enviros Consulting Ltd to support the development of a strategy for the assessment of environmental impacts from ionising radiation associated with the Olkiluoto waste repository, Finland, as part of the development of the Posiva Safety Case Portfolio. This project included a review of the development of international policies and standards related to protection of biota from the effects of ionizing radiation and of biota assessment methodologies, paying particular attention to those that have been applied to waste repository performance assessments. On the basis of this review, recommendations were developed on the most appropriate methodology to apply in order to assess the impact of radioactive releases from the planned spent fuel repository in Olkiluoto. A test-case was developed, in collaboration with staff from Posiva and Facilia AB, and an assessment was performed. The results and experience of which were analysed and summarised to develop recommendations for a future strategy. The test case highlighted some significant data gaps related to the assessment of impacts to both generic biota types and to interest species. In particular, concentration ratios for generic carnivorous mammals and migratory species such as moose that may consume food from multiple ecosystems and dose conversion factors for large burrowing (i.e. hibernating) mammals. However, in general terms, the dose rates predicted for all organism types were several orders of magnitude below those at which population effects would be expected to be observed and those at which effects on the individual may be anticipated. There would therefore be scope for simplifying the approach applied, although there would be value in performing a sensitivity analysis to ensure that the simplification is applied appropriately. There would also be value in ensuring consistency of the developing approach for non-human biota with

  12. Assessment of doses to non-human biota: Review of developments and demonstration assessment for Olkiluoto repository

    Energy Technology Data Exchange (ETDEWEB)

    Smith, K. [Carol Robinson Enviros Consulting Ltd, Edinburgh (United Kingdom)

    2006-12-15

    This report provides a summary of work commissioned by Posiva Oy and undertaken by Enviros Consulting Ltd to support the development of a strategy for the assessment of environmental impacts from ionising radiation associated with the Olkiluoto waste repository, Finland, as part of the development of the Posiva Safety Case Portfolio. This project included a review of the development of international policies and standards related to protection of biota from the effects of ionizing radiation and of biota assessment methodologies, paying particular attention to those that have been applied to waste repository performance assessments. On the basis of this review, recommendations were developed on the most appropriate methodology to apply in order to assess the impact of radioactive releases from the planned spent fuel repository in Olkiluoto. A test-case was developed, in collaboration with staff from Posiva and Facilia AB, and an assessment was performed. The results and experience of which were analysed and summarised to develop recommendations for a future strategy. The test case highlighted some significant data gaps related to the assessment of impacts to both generic biota types and to interest species. In particular, concentration ratios for generic carnivorous mammals and migratory species such as moose that may consume food from multiple ecosystems and dose conversion factors for large burrowing (i.e. hibernating) mammals. However, in general terms, the dose rates predicted for all organism types were several orders of magnitude below those at which population effects would be expected to be observed and those at which effects on the individual may be anticipated. There would therefore be scope for simplifying the approach applied, although there would be value in performing a sensitivity analysis to ensure that the simplification is applied appropriately. There would also be value in ensuring consistency of the developing approach for non-human biota with

  13. Results of monitoring at Olkiluoto in 2004. Rock mechanics

    International Nuclear Information System (INIS)

    Riikonen, S.

    2005-09-01

    This report presents Posiva Oy's results of the rock mechanical monitoring programme from the year 2004. Monitoring programme was established for long time monitoring of modifications in the bedrock during the excavation of the ONKALO underground research facility stated in Olkiluoto island. This is the first annual report where rock mechanical research work has being reported also from the monitoring point of view. Rock mechanical research work consists of both GPS measurements and microseismic measurements carried out in Olkiluoto island. Both measurements have been performed during several years even before monitoring programme was established. GPS measurements have been carried out since 1995 and microseismic network has operated since 2002. There have been no significant changes in observations when studying rock mechanical results from the year 2004 and comparing them to results from the previous years. Therefore it can be said, that so far ONKALO has barely had any effect on rock mechanics in Olkiluoto. Report has been composed from the annual reports of GPS measurements.(orig.)

  14. Fracture calcites at Olkiluoto. Evidence from quaternary infills for palaeohydrogeology

    International Nuclear Information System (INIS)

    Gehoer, S.; Kaerki, A.; Taikina-aho, O.; Karhu, J.; Loefman, J.; Pitkaenen, P.; Ruotsalainen, P.

    2002-02-01

    Recently formed secondary minerals, predominantly calcite, occur in varying amounts as fracture infills, and the calcite types, their chemical compositions and isotope ratios reflect the compositions and physicochemical factors of the groundwater system in which they were formed. Fluid inclusions trapped in calcites give direct evidence of trapping temperatures and past salinities and of the chemical compositions of the palaeo fluids. A wide range of mineralogical and geochemical examinations were carried out within the EQUIP project to examine features of this kind. The fracture calcites at the Olkiluoto site are of various origins and represent several textural types. The exact number of calcite-producing events is unknown, but the duration of the period that was appropriate for the precipitation of low temperature calcite is estimated to have exceeded 1000 Ma. Thus the number of genetically related calcite units is assumed to be considerable. This study was focused on the petrogenesis of calcites crystallized in fractures of high water conductivity during the latest stages of geological evolution. The majority of these late stage calcites form physically homogeneous, scaly layers, and in a few cases thin layers composed of idiomorphic crystals. Chemically these are almost stoichiometric calcites (CaCO 3 ). The MnO content may exceed 1%, while the amounts of other elements present are minor, although the trace element concentrations, particularly those of large ionic trace elements, can be used as distinguishing features for the recognition of individual precipitates representing different calcite generations. Evidence from fluid inclusions, or more correctly from the absence of these in the late stage calcites, can be interpreted as an indication of slow rates of crystallization under cool conditions. Many chemical variables, e.g. oxygen isotope ratios, demonstrate an equilibrium between the latest calcites and water similar to the present groundwater. Older

  15. Surface and near-surface hydrological model of Olkiluoto island

    International Nuclear Information System (INIS)

    Karvonen, T.

    2008-04-01

    The aim of the study was to develop a 3D-model that calculates the overall water balance components of Olkiluoto Island in the present-day condition utilizing the existing extensive data sets available. The model links the unsaturated and saturated soil water in the overburden and groundwater in bedrock to a continuous pressure system. The parameterization of land use and vegetation was done in such a way that the model can later on be used for description of the past evolution of the overburden hydrology at the site and overburden's hydrological evolution in the future. Measured groundwater level in overburden tubes, pressure heads in shallow bedrock holes, snow depth, soil temperature, frost depth and discharge measurements were used in assessing the performance of the models in the calibration period (01.05.2001- 31.12.2005). Computed groundwater level variation can be characterized by variables ΔH MEAS and ΔH COMP , which are the difference between maximum and minimum measured and computed groundwater level value during the calibration period. Average ΔH MEAS for all tubes located in fine-textured till soil was 1.99 m and the corresponding computed value ΔH COMP was 1.83 m. Average ΔH MEAS for all tubes located in sandy till soil was 2.12 m and the corresponding computed value ΔH COMP was 1.93 m. The computed results indicate that in future studies it is necessary to divide the two most important soil types into several subclasses. In the present study the uncertainty and sensitivity analysis was carried out through a parameter uncertainty framework known as GLUE. According to the uncertainty analysis the average yearly runoff was around 175 mm a -1 and 50 % confidence limits were 155 and 195 mm a -1 . Measured average yearly runoff during the calibration period was 190 mm a -1 . Average yearly evapotranspiration estimate was 310 mm a -1 and the 50 % confidence limits were 290 and 330 mm a -1 . Average value for recharge through the bedrock system was 1

  16. Fracture calcites at Olkiluoto. Evidence from quaternary infills for palaeohydrogeology

    Energy Technology Data Exchange (ETDEWEB)

    Gehoer, S.; Kaerki, A.; Taikina-aho, O. [Kivitieto Oy (Finland); Karhu, J. [Helsinki Univ. (Finland); Loefman, J. [VTT Processes, Espoo (Finland); Pitkaenen, P. [VTT Building and Transport, Espoo (Finland); Ruotsalainen, P. [TUKES, Helsinki (Finland)

    2002-02-01

    Recently formed secondary minerals, predominantly calcite, occur in varying amounts as fracture infills, and the calcite types, their chemical compositions and isotope ratios reflect the compositions and physicochemical factors of the groundwater system in which they were formed. Fluid inclusions trapped in calcites give direct evidence of trapping temperatures and past salinities and of the chemical compositions of the palaeo fluids. A wide range of mineralogical and geochemical examinations were carried out within the EQUIP project to examine features of this kind. The fracture calcites at the Olkiluoto site are of various origins and represent several textural types. The exact number of calcite-producing events is unknown, but the duration of the period that was appropriate for the precipitation of low temperature calcite is estimated to have exceeded 1000 Ma. Thus the number of genetically related calcite units is assumed to be considerable. This study was focused on the petrogenesis of calcites crystallized in fractures of high water conductivity during the latest stages of geological evolution. The majority of these late stage calcites form physically homogeneous, scaly layers, and in a few cases thin layers composed of idiomorphic crystals. Chemically these are almost stoichiometric calcites (CaCO{sub 3}). The MnO content may exceed 1%, while the amounts of other elements present are minor, although the trace element concentrations, particularly those of large ionic trace elements, can be used as distinguishing features for the recognition of individual precipitates representing different calcite generations. Evidence from fluid inclusions, or more correctly from the absence of these in the late stage calcites, can be interpreted as an indication of slow rates of crystallization under cool conditions. Many chemical variables, e.g. oxygen isotope ratios, demonstrate an equilibrium between the latest calcites and water similar to the present groundwater. Older

  17. Core drilling of deep borehole OL-KR39 at Olkiluoto in Eurajoki 2005

    Energy Technology Data Exchange (ETDEWEB)

    Niinimaeki, R. [Suomen Malmi Oy, Espoo (Finland)

    2005-11-15

    Posiva Oy submitted an application to the Finnish Government in May 1999 for the Decision in Principle to choose Olkiluoto in the municipality of Eurajoki as the site of the final disposal facility for spent nuclear fuel. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the decision in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) core drilled 502.97 m and 45.11 m deep boreholes with a diameter of 75.7 mm at Olkiluoto in August- October 2005. The identification numbers of the boreholes are OL-KR39 and OL-KR39B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the drilling water and the returning water were recorded. The drill rig was computer controlled and during drilling the computer recorded drilling parameters. The objective of all these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and flushing water were 415m{sup 3} and 25 m{sup 3} and the measured volumes of the returning water were 175 m{sup 3} and 7 m{sup 3} in boreholes OLKR39 and OL-KR39B, respectively. The deviation of the borehole was measured with the deviation measuring instruments EMS and Maxibor. Uniaxial compressive strength, Young's Modulus and Poisson' s ratio were measured from the core samples. The average uniaxial compressive strength is about 110 MPa, the average Young's Modulus is 49 GP a and the average Poisson' s ratio is 0.25. The main rock types are migmatitic mica gneiss and granite. Filled fracture is the most common

  18. Core drilling of deep borehole OL-KR37 at Olkiluoto in Eurajoki 2005

    Energy Technology Data Exchange (ETDEWEB)

    Niinimaeki, R. [Suomen Malmi Oy, Espoo (Finland)

    2005-11-15

    Posiva Oy submitted an application to the Finnish Government in May 1999 for the Decision in Principle to choose Olkiluoto in the municipality of Eurajoki as the site of the final disposal facility for spent nuclear fuel. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the decision in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) core drilled 350.00 m and 45.10 m deep boreholes with a diameter of 75.7 mm at Olkiluoto in June- August 2005. The identification numbers of the boreholes are OL-KR37 and OL-KR37B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the drilling water and the returning water were recorded. The drill rig was computer controlled and during drilling the computer recorded information about drilling parameters. The objective of all these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and flushing water were 273 m{sup 3} and 21m{sup 3} and the measured volumes of the returning water were 221m{sup 3} and 16m{sup 3} in boreholes OL-KR37 and OL-KR37B, respectively. The deviation of the borehole was measured with the deviation measuring instruments EMS and Maxibor. Uniaxial compressive strength, Young's Modulus and Poisson' s ratio were measured from the core samples. The average uniaxial compressive strength is about 106 MPa, the average Young's modulus is 40 GPa and the average Poisson's ratio is 0.20. The main rock types are migmatitic mica gneiss, granite and tonalite. Filled

  19. Foliation: Geological background, rock mechanics significance, and preliminary investigations at Olkiluoto

    International Nuclear Information System (INIS)

    Milnes, A.G.; Hudson, J.; Wikstroem, L.; Aaltonen, I.

    2006-01-01

    A well developed, pervasive foliation is a characteristic feature of the migmatites and gneisses in the Olkiluoto bedrock, and is expected to have a significant influence on the underground construction, the design and layout and the groundwater flow regime of a deep spent nuclear fuel repository. This Working Report reviews the geological background and rock mechanics significance of foliation, and develops a methodology for the systematic acquisition of foliation data in cored boreholes and in tunnels at the Olkiluoto site, to provide the necessary basis for future geological, rock mechanics and hydrogeological modelling. The first part of the methodology concerns foliation characterisation, and develops a characterisation scheme based on two variables: the foliation type (G = gneissic, B = banded, S = schistose), which is a function of mineral composition and degree of smallscale heterogeneity, and the foliation intensity (1 = low, 2 = intermediate, 3 = high), which is a function of the type and intensity of the deformation by which it was produced (under high-grade metamorphic conditions in the core of the Svecofennian orogenic belt). At the suggested reference scales (1 m length of core, 10 m 2 area of tunnel wall), the most representative foliation type and intensity is assessed using a standard set of core photographs, which are included as an Appendix at the end of the report, providing a systematic description in terms of 9 descriptive types (G1, G2, G3, B1, B2, B3, S1, S2, S3). As a further step, the rock mechanics significance of these types is assessed and a rock mechanics foliation (RMF) number is assigned (RMF 0 = no significance, RMF 1, RMF 2 and RMF 3 = low, intermediate and high significance, respectively). The second part of the methodology concerns the orientations of the foliation within the same 1 m core lengths or 10 m2 wall areas, which have been characterised as above. This combined analysis of foliation character and foliation orientation

  20. Fracture toughness properties of rocks in Olkiluoto: Laboratory measurements 2008-2009

    Energy Technology Data Exchange (ETDEWEB)

    Siren, T.

    2012-05-15

    In Olkiluoto an underground rock characterization facility (ONKALO) for the final disposal site of spent nuclear fuel has been under thorough research many years, but further knowledge is needed on fracture toughness parameters. Fracture toughness parameters are important for example in fracture mechanics prediction for Posiva's Olkiluoto Spalling Experiment (POSE). This working report describes a laboratory campaign that was done between 2008 and 2009. The campaign aimed at determining the fracture mechanics parameters as well as density and ultrasonic velocities for Olkiluoto rocks. The specimens delivered were selected by Posiva; the core showed no damage and the quality of the delivered cores was good with varying sample diameter. Most of the test samples (9 out of 12) are gneissic rock. The Mode I fracture toughness was determined using two different methods to account for two different fracturing directions. The methods are the Chevron Bend (CB) test as proposed in the ISRM Suggested Method and a method based on the Brazilian Disk (BD) experiment. The Mode II fracture toughness was determined using the Punch-Through Shear with Confining Pressure experiment on the remaining pieces from the CB testing. The scatter in the results is very large, even within one piece of core sample. Usually the scatter of results is less than 5 %. The high scatter in the data at hand is believed to be due to the very inhomogeneous nature of the rock material. The magnitude of the determined Mode I fracture toughness compares well with available reported data for medium to coarse grained granitoide rocks. However the scatter of the mode II fracture toughness values is higher than experienced on other rock types, but the variability is reasonable for the inhomogeneous rock type. Distinguishing the fracture toughness values for different anisotropy directions would require more thorough testing with quality samples at different anisotropy directions. However since fracture

  1. Core drilling of deep borehole OL-KR39 at Olkiluoto in Eurajoki 2005

    International Nuclear Information System (INIS)

    Niinimaeki, R.

    2005-11-01

    Posiva Oy submitted an application to the Finnish Government in May 1999 for the Decision in Principle to choose Olkiluoto in the municipality of Eurajoki as the site of the final disposal facility for spent nuclear fuel. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the decision in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) core drilled 502.97 m and 45.11 m deep boreholes with a diameter of 75.7 mm at Olkiluoto in August- October 2005. The identification numbers of the boreholes are OL-KR39 and OL-KR39B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the drilling water and the returning water were recorded. The drill rig was computer controlled and during drilling the computer recorded drilling parameters. The objective of all these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and flushing water were 415m 3 and 25 m 3 and the measured volumes of the returning water were 175 m 3 and 7 m 3 in boreholes OLKR39 and OL-KR39B, respectively. The deviation of the borehole was measured with the deviation measuring instruments EMS and Maxibor. Uniaxial compressive strength, Young's Modulus and Poisson' s ratio were measured from the core samples. The average uniaxial compressive strength is about 110 MPa, the average Young's Modulus is 49 GP a and the average Poisson' s ratio is 0.25. The main rock types are migmatitic mica gneiss and granite. Filled fracture is the most common fracture type. The average fracture

  2. Core drilling of deep borehole OL-KR43 at Olkiluoto in Eurajoki 2006

    Energy Technology Data Exchange (ETDEWEB)

    Niinimaeki, R. [Suomen Malmi Oy, Espoo (Finland)

    2006-12-15

    Posiva Oy submitted an application to the Finnish Government in May 1999 for the Decision in Principle to choose Olkiluoto in the municipality of Eurajoki as the site of the final disposal facility for spent nuclear fuel. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the decision in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) core drilled 1000.26 m and 45.01 m deep boreholes with a diameter of 75.7 mm at Olkiluoto in July - October 2006. The identification numbers of the boreholes are OL-KR43 and OL-KR43B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the drilling water and the returning water were recorded. The drill rig was computer controlled and during drilling the computer recorded drilling parameters. The objective of all these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and flushing water were 1103 m{sup 3} and 16 m{sup 3} in boreholes OL-KR43 and OL-KR43B, respectively. Measured volumes of the returning water were 916m{sup 3} in borehole OL-KR43 and 13m{sup 3} in borehole OL-KR43B. The deviation of the boreholes was measured with the deviation measuring instruments EMS and Maxibor. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive strength is about 131 MPa, the average Young's Modulus is 37 GPa and the average Poisson's ratio is 0.19. The main rock types are veined gneiss, diatexitic gneiss

  3. Core drilling of deep borehole OL-KR46 at Olkiluoto in Eurajoki 2007

    International Nuclear Information System (INIS)

    Toropainen, V.

    2007-09-01

    Posiva Oy submitted an application to the Finnish Government in May 1999 for the Decision in Principle to choose Olkiluoto in the municipality of Eurajoki as the site of the final disposal facility for spent nuclear fuel. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the decision in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) core drilled 600.10 m and 45.16 m deep boreholes with a diameter of 75.7 mm at Olkiluoto in May - June 2007. The identification numbers of the boreholes are OL-KR46 and OL-KR46B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the returning water, and the volume of drilling water were recorded. The drill rig was computer controlled and during drilling the computer recorded drilling parameters. The objective of all these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and flushing water were 466 m 3 and 20 m 3 in boreholes OL-KR46 and OL-KR46B, respectively. Measured volumes of the returning water were 407 m 3 in borehole OL-KR46 and 12 m 3 in borehole OL-KR46B. The deviation of the boreholes was measured with the deviation measuring instruments EMS and Maxibor. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive strength is 116.5 MPa, the average Young's Modulus is 31.5 GPa and the average Poisson's ratio is 0.20. The main rock types are veined gneiss, tonalitic-granodioritic-granitic gneiss and pegmatite

  4. Core drilling of deep drillhole OL-KR45 at Olkiluoto in Eurajoki 2007

    International Nuclear Information System (INIS)

    Toropainen, V.

    2007-11-01

    Posiva Oy submitted an application to the Finnish Government in May 1999 for the Decision in Principle to choose Olkiluoto in the municipality of Eurajoki as the site of the final disposal facility for spent nuclear fuel. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the decision in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) core drilled 1023.30 m and 44.75 m deep drillholes with a diameter of 75.7 mm at Olkiluoto in June - September 2007. The identification numbers of the drillholes are OL-KR45 and OL-KR45B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the returning and drilling waters were recorded. The drill rig was computer controlled and during drilling the computer recorded drilling parameters. The objective of all these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and washing water were 1186 m 3 and 19 m 3 in drillholes OL-KR45 and OL-KR45B, respectively. Measured volumes of the returning water were 962 m 3 in drillhole OL-KR45 and 15 m 3 in drillhole OL-KR45B. The deviation of the drillholes was measured with the deviation measuring instruments EMS and Maxibor II. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive strength is 126.2 MPa, the average Young's Modulus is 42.5 GPa and the average Poisson's ratio is 0.21. The main rock types are veined and diatexitic gneisses, pegmatitic granite and tonalitic

  5. Energy taxation in Finland

    International Nuclear Information System (INIS)

    Valtonen, M.

    1991-01-01

    Energy taxation in Finland is described in addition to plans for reforms in this respect. It is stated that taxation on energy has primarily a fiscal motive, and it can also be used as a means of steering of energy and environmental policy. Numerical data illustrate the text. (AB)

  6. National programme: Finland

    International Nuclear Information System (INIS)

    Forsten, J.

    1986-01-01

    Finland's programmes in the field of reactor pressure components are presented in this paper. The following information on each of these programmes is given: the brief description of the programme; the programme's schedule and duration; the name of the project manager

  7. Energy efficiency in Finland

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    In Finland a significant portion of energy originates from renewable sources and cogeneration, that is, combined production of electricity and heat. Combined heat and electricity production is typical in the Finnish industry and in the district heating sector. One third of all electricity and 15 % of district heating is produced by cogeneration. District heating schemes provide about 45 % of heat in buildings. Overall efficiency in industry exceeds 80 % and is even higher in the district heating sector. In 1996 25 % of Finland`s primary energy was produced from renewable energy sources which is a far higher proportion than the European Union average of 6 %. Finland is one of the leading users of bioenergy. Biomass including peat, provides approximately 50 % of fuel consumed by industry and is utilised in significant amounts in combined heat and electricity plants. For example, in the pulp and paper industry, by burning black liquor and bark during the production of chemical pulp, significant amounts of energy are generated and used in paper mills. Conservation and efficient use of energy are central to the Finnish Government`s Energy Strategy. The energy conservation programme aims to increase energy efficiency by 10-20 % by the year 2010. Energy saving technology plays a key role in making the production and use of energy more efficient. In 1996 of FIM 335 million (ECU 57 million) spent on funding research, FIM 120 million (ECU 20 million) was spent on research into energy conservation

  8. Results of Monitoring at Olkiluoto in 2007. Hydrogeochemistry

    Energy Technology Data Exchange (ETDEWEB)

    Pitkaenen, P.; Partamies, S. (VTT, Espoo (Finland)); Lahdenperae, A.-M.; Ahokas, T.; Penttinen, T. (Poeyry Environment Oy, Vantaa (Finland)); Lehtinen, A. (Posiva Oy, Helsinki (Finland)); Pedersen, K. (Microbial Analytics Sweden AB (Sweden)); Lamminmaeki, T. (Teollisuuden Voima Oy, Olkiluoto (Finland)); Hatanpaeae, E. (Ramboll Analytics Oy, Lahti (Finland))

    2008-07-15

    The construction of underground research facility ONKALO will inevitably affect the rock mass and the groundwater flow system. It will also affect the chemical environment both at the surface and at depth. In order to determine the magnitude and extent of such effects it was necessary to set up a monitoring system that is capable of measuring the resulting cases to the necessary accuracy and extent and due to monitoring programme was established. In 2007 groundwater samples were taken from both the overburden and deep bedrock by different methods. Samples were taken from the surface and from ONKALO. Shallow groundwater has been monitored both in shallow drillholes and in groundwater observation tubes located in the overburden. A total of 40 shallow groundwater samples were taken in 2007. The main reasons for shallow groundwater quality changes are probably changes in precipitation and the fluctuation of the groundwater table. Construction work in ONKALO and in its surrounding does not seem to have affected groundwater quality in the shallow groundwater tubes and drillholes. Natural factors, e.g. site geology, closeness of sea, local climate are more important, as well as human impact, mainly relatively heavy infrastructural works and road salting. According to the 2007 results, deep groundwater compositions are very similar to the baseline data. The observed changes in the time series data seem to be caused by the hydraulic zones and the periods when the drillholes have been open. However, the length of the monitoring period of the time series samples is still insufficient for making any estimation about the potential influences on the groundwater chemistry caused by the construction of ONKALO. Certain volumes of bedrock, e.g. the area in the vicinity of OL-KR8, seem to be exceptionally stable despite the location next to ONKALO. Two sampling sections near ONKALO (OL-KR22-T390 and OL-KR23-T424, both HZ20 intersections) show a clear increase in dissolved sulphide

  9. Core drilling of deep drillhole OL-KR57 at Olkiluoto in Eurajoki 2011-2012

    International Nuclear Information System (INIS)

    Toropainen, V.

    2012-07-01

    As a part of the confirming site investigations at Olkiluoto, Suomen Malmi Oy (Smoy) core drilled 401.71 m and 45.01 m deep drillholes, OL-KR57 and OL-KR57B, at Olkiluoto in September 2011 - January 2012. The diameter of the drillholes is 75.7 mm. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the returning and drilling water were recorded. The drill rig was computer controlled and the computer recorded drilling parameters during drilling. The objective of the measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling, flushing and washing water were 350 m3 and 30 m3 in the drillholes OL-KR57 and OL-KR57B, respectively. The measured volumes of the returning water in the drillholes were 328 m 3 and 16.8 m 3 , respectively. The deviations of the drillholes were measured with the deviation measuring instruments EMS and Gyro. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive strength was 123.9 MPa, the average Young's Modulus was 42.6 GPa and the average Poisson's ratio was 0.23. The main rock types are veined and diatexitic gneisses, mica gneiss and tonaliticgranodioritic- granitic gneiss. The average fracture frequency is 2.5 pcs/m in drillhole OL-KR57 and 3.3 pcs/m in the drillhole OL-KR57B. The average RQD values are 95.0 % and 93.0 %. Seven separate fractured zones were interpreted from OL-KR57 and three fractured zones from OL-KR57B. (orig.)

  10. Core drilling of deep drillhole OL-KR56 at Olkiluoto in Eurajoki 2011 - 2012

    Energy Technology Data Exchange (ETDEWEB)

    Toropainen, V. [Suomen Malmi Oy, Espoo (Finland)

    2012-07-15

    As a part of the confirming site investigations at Olkiluoto, Suomen Malmi Oy (Smoy) core drilled a 1201.65 m deep drillhole with a diameter of 75.7 mm at Olkiluoto in October 2011 - January 2012. The identification number of the drillhole is OL-KR56. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the returning and drilling water were recorded. The drill rig was computer controlled and the computer recorded drilling parameters during drilling. The objective of the measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volume of the used drilling, washing and flushing water was 1628 m{sup 3}. The measured volume of the returning water in the drillhole was 1142 m{sup 3}. The deviation of the drillhole was measured with the deviation measuring instruments Reflex EMS and Reflex Gyro. The main rock types are veined and diatexitic gneisses, pegmatitic granite and mica gneiss. The average fracture frequency is 2.4 pcs/m and the average RQD value is 96.2 %. Fifty fractured zones were penetrated by the drillhole. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive strength was 120.0 MPa, the average Young's Modulus was 38.3 GPa and the average Poisson's ratio was 0.22. (orig.)

  11. Core drilling of deep drillhole OL-KR50 at Olkiluoto in Eurajoki 2008

    International Nuclear Information System (INIS)

    Toropainen, V.

    2009-02-01

    As a part of the confirming site investigations at Olkiluoto, Suomen Malmi Oy (Smoy) core drilled 939.33 m and 45.44 m deep drillholes with a diameter of 75.7 mm at Olkiluoto in September - November 2008. The identification numbers of the drillholes are OL-KR50 and OL-KR50B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the returning and drilling water were recorded. The drill rig was computer controlled and the computer recorded drilling parameters during drilling. The objective of the measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and washing water were 1135 m 3 and 20 m 3 in the drillholes OL-KR50 and OL-KR50B, respectively. The measured volume of the returning water in the drillhole OL-KR50 was 954 m 3 . The deviation of the drillholes was measured with the deviation measuring instruments EMS and Maxibor II. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive strength was 129.7 MPa, the average Young's Modulus was 45.8 GPa and the average Poisson's ratio was 0.15. The main rock types were veined and diatexitic gneisses, pegmatitic granite and tonaliticgranodioritic-granitic gneiss. The average fracture frequency is 2.0 pcs/m in drillhole OL KR50 and 3.6 pcs/m in the drillhole OL-KR50B. The average RQD values are 96.1 % and 94.3 %, respectively. 39 fractured zones were penetrated by drillhole OL-KR50 and four by drillhole OL-KR50B. (orig.)

  12. The estimation of future surface water bodies at Olkiluoto area based on statistical terrain and land uplift models

    Energy Technology Data Exchange (ETDEWEB)

    Pohjola, J.; Turunen, J.; Lipping, T. [Tampere Univ. of Technology (Finland); Ikonen, A.

    2014-03-15

    In this working report the modelling effort of future landscape development and surface water body formation at the modelling area in the vicinity of the Olkiluoto Island is presented. Estimation of the features of future surface water bodies is based on probabilistic terrain and land uplift models presented in previous working reports. The estimation is done using a GIS-based toolbox called UNTAMO. The future surface water bodies are estimated in 10 000 years' time span with 1000 years' intervals for the safety assessment of disposal of spent nuclear fuel at the Olkiluoto site. In the report a brief overview on the techniques used for probabilistic terrain modelling, land uplift modelling and hydrological modelling are presented first. The latter part of the report describes the results of the modelling effort. The main features of the future landscape - the four lakes forming in the vicinity of the Olkiluoto Island - are identified and the probabilistic model of the shoreline displacement is presented. The area and volume of the four lakes is modelled in a probabilistic manner. All the simulations have been performed for three scenarios two of which are based on 10 realizations of the probabilistic digital terrain model (DTM) and 10 realizations of the probabilistic land uplift model. These two scenarios differ from each other by the eustatic curve used in the land uplift model. The third scenario employs 50 realizations of the probabilistic DTM while a deterministic land uplift model, derived solely from the current land uplift rate, is used. The results indicate that the two scenarios based on the probabilistic land uplift model behave in a similar manner while the third model overestimates past and future land uplift rates. The main features of the landscape are nevertheless similar also for the third scenario. Prediction results for the volumes of the future lakes indicate that a couple of highly probably lake formation scenarios can be identified

  13. The estimation of future surface water bodies at Olkiluoto area based on statistical terrain and land uplift models

    International Nuclear Information System (INIS)

    Pohjola, J.; Turunen, J.; Lipping, T.; Ikonen, A.

    2014-03-01

    In this working report the modelling effort of future landscape development and surface water body formation at the modelling area in the vicinity of the Olkiluoto Island is presented. Estimation of the features of future surface water bodies is based on probabilistic terrain and land uplift models presented in previous working reports. The estimation is done using a GIS-based toolbox called UNTAMO. The future surface water bodies are estimated in 10 000 years' time span with 1000 years' intervals for the safety assessment of disposal of spent nuclear fuel at the Olkiluoto site. In the report a brief overview on the techniques used for probabilistic terrain modelling, land uplift modelling and hydrological modelling are presented first. The latter part of the report describes the results of the modelling effort. The main features of the future landscape - the four lakes forming in the vicinity of the Olkiluoto Island - are identified and the probabilistic model of the shoreline displacement is presented. The area and volume of the four lakes is modelled in a probabilistic manner. All the simulations have been performed for three scenarios two of which are based on 10 realizations of the probabilistic digital terrain model (DTM) and 10 realizations of the probabilistic land uplift model. These two scenarios differ from each other by the eustatic curve used in the land uplift model. The third scenario employs 50 realizations of the probabilistic DTM while a deterministic land uplift model, derived solely from the current land uplift rate, is used. The results indicate that the two scenarios based on the probabilistic land uplift model behave in a similar manner while the third model overestimates past and future land uplift rates. The main features of the landscape are nevertheless similar also for the third scenario. Prediction results for the volumes of the future lakes indicate that a couple of highly probably lake formation scenarios can be identified with other

  14. Safety assessment of spent fuel disposal in Haestholmen, Kivetty, Olkiluoto and Romuvaara - TILA-99

    Energy Technology Data Exchange (ETDEWEB)

    Vieno, T.; Nordman, H. [VTT Energy (Finland)

    1999-03-01

    The spent fuel from the Finnish nuclear power plants is planned to be disposed of in copper-iron canisters emplaced in a KBS-3 type repository constructed at a depth of about 500 metres at one of the four candidate sites investigated. The disposal concept aims at long-term isolation of the spent fuel assemblies from the biosphere and even from the geosphere. The evaluation of the normal evolution of the disposal system accords with the conclusions of the previous Finnish, Swedish and Canadian safety assessments of similar disposal concepts. Subject to the influence of the expected, normal evolution of the repository, initially intact copper-iron canisters will most likely preserve their integrity for more than one million years at any of the candidate sites. Consequently, the best-estimate assessment is that there never will be any significant releases of radionuclides from the repository into the geosphere. Consequences of potential canister failures have been evaluated using conservative assumptions, models and data. The results show that at any of the sites a large number of canisters could be assumed to be initially defective or to `disappear` simultaneously after some time without that the proposed constraints for release rates into the biosphere or dose rates were exceeded. In most cases this conclusion is valid for all canisters failing simultaneously, even if rather pessimistic flow and transport data is used. In the sensitivity and `what if` analyses where very high flow rates of saline groundwater are assumed, highest release and dose rates are caused by weakly-sorbing cations Sr-90 and Ra-226. The most important differences between the sites are related to the coastal location and brackish/saline groundwater of Haestholmen and Olkiluoto, and on the other hand to the inland location and fresh groundwater of Kivetty and Romuvaara. Because of the ongoing postglacial land uplift at the coast of the Baltic Sea, Olkiluoto and Haestholmen, too, may become

  15. Safety assessment of spent fuel disposal in Haestholmen, Kivetty, Olkiluoto and Romuvaara - TILA-99

    International Nuclear Information System (INIS)

    Vieno, T.; Nordman, H.

    1999-03-01

    The spent fuel from the Finnish nuclear power plants is planned to be disposed of in copper-iron canisters emplaced in a KBS-3 type repository constructed at a depth of about 500 metres at one of the four candidate sites investigated. The disposal concept aims at long-term isolation of the spent fuel assemblies from the biosphere and even from the geosphere. The evaluation of the normal evolution of the disposal system accords with the conclusions of the previous Finnish, Swedish and Canadian safety assessments of similar disposal concepts. Subject to the influence of the expected, normal evolution of the repository, initially intact copper-iron canisters will most likely preserve their integrity for more than one million years at any of the candidate sites. Consequently, the best-estimate assessment is that there never will be any significant releases of radionuclides from the repository into the geosphere. Consequences of potential canister failures have been evaluated using conservative assumptions, models and data. The results show that at any of the sites a large number of canisters could be assumed to be initially defective or to 'disappear' simultaneously after some time without that the proposed constraints for release rates into the biosphere or dose rates were exceeded. In most cases this conclusion is valid for all canisters failing simultaneously, even if rather pessimistic flow and transport data is used. In the sensitivity and 'what if' analyses where very high flow rates of saline groundwater are assumed, highest release and dose rates are caused by weakly-sorbing cations Sr-90 and Ra-226. The most important differences between the sites are related to the coastal location and brackish/saline groundwater of Haestholmen and Olkiluoto, and on the other hand to the inland location and fresh groundwater of Kivetty and Romuvaara. Because of the ongoing postglacial land uplift at the coast of the Baltic Sea, Olkiluoto and Haestholmen, too, may become

  16. Report of the Committee for Nuclear Energy Competence in Finland

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-07-01

    In October 2010, the Ministry of Employment and the Economy set up a committee to examine the long-term competence needs of the nuclear energy sector. The study was implemented by a group of experts ensuring extensive representation of the nuclear energy sector. One of the key conclusions was that comprehensive high-standard national competence is needed by nuclear sector companies and research institutes, as well as by authorities. Training of experts and sector-specific research activities call for long-term investments and cooperation, both among national actors and on an international scale. Competence needs in Finland's nuclear energy sector are growing. The nuclear power plant units presently in operation, as well as the Olkiluoto 3 unit under construction, require a competent labour force on a continuous basis. Posiva must have readiness for commencing final disposal of spent fuel by 2020. The new nuclear power projects - TVO's Olkiluoto 4 and Fennovoima's nuclear power plant, which were given favourable decisions-in-principle by the Government in 2010 - will particularly increase the need for experts. In its statement when ratifying these decisions-in-principle on 1 July 2010 Parliament required that the Government will, for its own part, create the preconditions for utilising Finnish labour, knowledge and business life as far as possible in nuclear power projects. The appointment letter of 27 October 2010 assigns the following duties to the Committee for Nuclear Energy Competence: (1) to survey the present personnel resources of nuclear actors; (2) to conduct an extensive review of the need for Finnish basic higher education, postgraduate education, further education and supplementary training; (3) to investigate the opportunities for Finnish participation in the forthcoming major nuclear power plant projects; (4) to survey the research infrastructure available to nuclear actors and research; (5) to examine Finnish research activities and

  17. Keeping Finland warm

    International Nuclear Information System (INIS)

    2006-01-01

    Close to 80% of the district heat produced in Finland is generated in combined heat and power (CHP) plants. This is a very high figure, and compares favourably with the situation else here, even in neighbouring Sweden, where local CHP facilities only account for 20% of district heat generation, because of the major role played by hydropower and nuclear. District heat is well-established, and has a 48% market share in Finland. Sales are growing by between 1% and 1,5% a year in terms of temperature-corrected offtake volume. This compares to a 50% market share in Sweden. District heat contracts generally follow recommendations drawn up by Finnish Energy Industries in cooperation with the country's competition and consumer protection authorities. This has promoted a consistent level of best practice and prevented unnecessary disputes between suppliers and customers

  18. Groundwater salinity at Olkiluoto and its effects on a spent fuel repository

    Energy Technology Data Exchange (ETDEWEB)

    Vieno, T. [VTT Energy, Espoo (Finland)

    2000-06-01

    The Olkiluoto island rose from the Baltic Sea 2500 to 3000 years ago. The layered sequence of groundwaters can be related to climatic and shoreline changes from modern tune through former Baltic stages to the deglaciation phase about 10 000 years ago and even to preglacial times. Fresh groundwater is found to the depth of about 150 metres, brackish between 100 and 400 metres, deeper groundwaters are saline. At the depth of 500 meters, the content of Total Dissolved Solids (TDS) varies between 10 and 25 g/l. The most saline waters at depths greater than 800 metres have TDS values between 30 and 75 g/l. These deep saline waters seem to have been undisturbed during the most recent glaciation and even much longer in the past. Today fresh water infiltrating at the surface gradually displaces brackish and saline groundwater in the bedrock. Due to the still ongoing postglacial land uplift, Olkiluoto is likely to become an inland site with brackish or fresh groundwater at the depth of 500 metres within the next 10 000 years. During the construction and operation phases groundwater will be drawn into the repository from the surrounding bedrock. As a consequence, more saline groundwaters, presently laying 100 to 200 metres below the repository level, may rise to the disposal level. After the closing of the repository the salinity distribution will gradually return towards the natural state. During the glacial cycle groundwater salinity may increase, for example, during freezing of groundwater into permafrost, when dissolved solids concentrate in the remaining water phase, and in a situation where deep saline groundwaters from under the centre of the glacier are pushed to the upper parts of the bedrock at the periphery of the glacier. The most significant open issue related to saline groundwater is the performance of the tunnel backfill which in the BS-3 concept has been planned to consist of a mixture of crushed rock and 10-30% of bentonite. Saline groundwater may

  19. Nuclear energy in Finland

    International Nuclear Information System (INIS)

    2008-01-01

    The booklet provides and up-to-date overview of the use of nuclear energy in Finland as well as future plans regarding the nuclear energy sector. It is intended for people working in the nuclear or energy sector in other countries, as well as for those international audiences and decision-makers who would like to have extra information on this particular energy sector. In the booklet nuclear energy is described as part of the Finnish electricity market

  20. NPPCI activities in Finland

    International Nuclear Information System (INIS)

    Wahlstroem, B.

    1986-01-01

    Research activities at the Technical Research Centre of Finland in the control and instrumentation field have been directed both towards immediate needs and towards long term goals. The immediate needs have been connected to different ongoing investigations and to development projects in connection with process industry. Of the more long term projects the following can be explicitly mentioned: the Nordic project on human reliability; work on software reliability; design guides for digital CI systems; simulation of technical processes; artificial intelligence in nuclear power

  1. Preventing BEPS in Finland

    OpenAIRE

    Sourinthone, Aksone

    2017-01-01

    In the recent years, the focus on multinationals’ tax avoidance schemes or Base Erosion & Profit Shifting (BEPS) has been increasing constantly. The OECD and the European Commission are working on new tax rulings to counter those harmful practices. The report aims to analyse and assess the anti-BEPS package: what does it contain, how can it be effective on the European level and how is Finland implementing the new recommendations? The analysis was a desktop study: peer-reviewed articles, ...

  2. Energy attitudes in Finland

    International Nuclear Information System (INIS)

    Ruuskanen, A.T.; Jaervinen, P.J.

    1984-01-01

    Energy issues are at present heavily debated in Finland. Public discussion is very emotional and biased against nuclear power. The undetermined situation together with the need for a decision on increasing the nuclear capacity led Imatran Voima Oy (Imatra Power Company) to measure the prevailing attitudes. The paper discusses the energy opinion surveys recently made in Finland. The general results give evidence of the changes occurring in the values of life. Environmental issues and the purity of energy production are seen as the most important factors of energy policy. Low price or availability and reliability are considered less important. The results of the surveys show, however, that people think that more electricity will be needed in the future. Natural gas, peat and hydroelectric power are most favoured. The attitude towards the use of coal and nuclear power is clearly more diffuse. In the survey, 21% want to increase the share of nuclear power, 32% want to keep its use at the present level and 35% want to reduce it. This 35% includes the one-fifth of the population that would like to abandon nuclear power altogether. Nuclear wastes and accidents are considered the most important factors contributing to the formation of attitudes towards nuclear energy. The other main factors are discussed in the paper. A great desire for information on energy policy together with personal decision making interests reflect the general attitude in Finland also. Totally incorrect information on nuclear energy is, however, surprisingly prevalent, which makes opposition to nuclear power understandable. All these factors make taking a decision on a fifth nuclear power plant in Finland difficult. (author)

  3. Nuclear energy in Finland

    International Nuclear Information System (INIS)

    Kilpi, K.; Palmen, B.

    1983-01-01

    Finland currently generates about 40% of its electricity from nuclear power. This achievement of worldwide record magnitude is based on long-lasting efforts to build and maintain the competent infrastructure and close international cooperation required by this demanding technology. This booklet published by the Finnish Atomic Energy Commission gives an overview of nuclear energy and related organizations in Finland. It describes the utility companies and nuclear power production, the manufacturing industry and its export potential, research and educational activities and the legal framework and authorities for nuclear safety and administration. International cooperation has been essential for Finland in developing its nuclear energy capacity and appreciation is espressed to many countries and international organizations which have contributed to this. At the same time Finnish organizations are willing to share the experiences and know-how they have gained in building nuclear power in a small country. This is a road which will be followed by many other countries in the decades to come. It is hoped that this booklet will also help to open new channels of cooperation in such efforts

  4. Geophysical investigations in the Kivetty area, Finland

    International Nuclear Information System (INIS)

    Heikkinen, E.; Paananen, M.; Oehberg, A.; Front, K.; Okko, O.; Pitkaenen, P.

    1992-09-01

    Investigations were carried out at Kivetty site in Konginkangas, in central Finland, by geological, geophysical, geohydrological and geochemical methods in 1987-1991 to determine the suitability of the bedrock for the final disposal of spent nuclear fuel. Airborne, ground and borehole geophysical methods were used to study the rock type distribution, fracturing and hydraulic conductivity of the bedrock to a depth of one kilometre

  5. Disposal of spent fuel in Olkiluoto bedrock. Programme for research, development and technical design for the pre-construction phase

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-12-01

    The spent fuel from the nuclear power plants at Olkiluoto and Loviisa will be disposed of in Finnish bedrock. Posiva aims at starting the construction of the disposal facility in the 2010's and the actual disposal operations in 2020. In May 1999 Posiva submitted an application for the so-called Decision-in-Principle (DiP) on the facility to the Finnish Government. According to the application the repository would be based on a KBS-3 type concept and sited at Olkiluoto. The application was approved by the Government in December 2000 and will go next to the Parliament for final approval. However, Posiva has already started the planning for the next programme phase on the assumption that a positive decision will be made. The purpose of the present document is to describe the objectives and major items of research, development, technical planning and design work for the period preceding the construction license. According to the current official guidelines Posiva should prepare for submitting the application for the license in 2010. For the technical development and design work the main target for the starting programme phase is to reach the maturity of design and technical plans that allows the specification of work packages for bid calls and gives sufficient confidence in the technical feasibility of planned operations at the encapsulation facility and in the repository. The main objectives for the complementary characterisation work at Olkiluoto consist of the verification of the present conclusions on site suitability, the definition and identification of suitable rock volumes for repository space and the characterisation of the target host rock for repository design, safety assessment and planning of construction work. The technical design and demonstration work together with the results of complementary site characterisation will provide the basis of the safety case prepared as the support for the construction license application. An integrated safety

  6. Disposal of spent fuel in Olkiluoto bedrock. Programme for research, development and technical design for the pre-construction phase

    International Nuclear Information System (INIS)

    2000-12-01

    The spent fuel from the nuclear power plants at Olkiluoto and Loviisa will be disposed of in Finnish bedrock. Posiva aims at starting the construction of the disposal facility in the 2010's and the actual disposal operations in 2020. In May 1999 Posiva submitted an application for the so-called Decision-in-Principle (DiP) on the facility to the Finnish Government. According to the application the repository would be based on a KBS-3 type concept and sited at Olkiluoto. The application was approved by the Government in December 2000 and will go next to the Parliament for final approval. However, Posiva has already started the planning for the next programme phase on the assumption that a positive decision will be made. The purpose of the present document is to describe the objectives and major items of research, development, technical planning and design work for the period preceding the construction license. According to the current official guidelines Posiva should prepare for submitting the application for the license in 2010. For the technical development and design work the main target for the starting programme phase is to reach the maturity of design and technical plans that allows the specification of work packages for bid calls and gives sufficient confidence in the technical feasibility of planned operations at the encapsulation facility and in the repository. The main objectives for the complementary characterisation work at Olkiluoto consist of the verification of the present conclusions on site suitability, the definition and identification of suitable rock volumes for repository space and the characterisation of the target host rock for repository design, safety assessment and planning of construction work. The technical design and demonstration work together with the results of complementary site characterisation will provide the basis of the safety case prepared as the support for the construction license application. An integrated safety assessment

  7. Results of monitoring at Olkiluoto in 2012. Environment

    International Nuclear Information System (INIS)

    Haapanen, A.

    2014-04-01

    In 2003, Posiva Oy presented a programme for monitoring at Olkiluoto during construction and operation of ONKALO. In 2012 the monitoring programme was updated to concern the years 2012-2018. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). This Working Report presents the main results of Posiva's environmental monitoring programme on Olkiluoto Island in 2012. Results are presented under five topics: 1. Evolution of geosphere, 2. Biosphere modelling input data, 3. Interaction between surface environment and groundwater in bedrock, 4. Environmental impact and 5. Baseline of monitoring of radioactive releases. Concerning the evolution of geosphere, LIDAR-scannings were done in the Olkiluoto area in 2012. The acquired data can be used for elevation and other modelling purposes. The soil solution quality in 2012 was quite comparable to that in earlier years. Proximity of the sea and the young age of soils are seen in soil solution results. Biosphere modelling input data in 2012 included e.g. continuous tree litterfall and transpiration data, as well as updated game statistics and population estimates of fauna, a fishery survey from the River Eurajoki (2011) and basic monitoring data from Olkiluoto offshore properties. Interaction between surface environment and groundwater in bedrock includes e.g. weather and surface water monitoring data. Environmental impact analyses included e.g. monitoring of noise, air quality, effluent waters and private drilled wells. Noise monitoring in the vicinity of ONKALO showed that in the case of raised noise levels the sources are mainly the traffic on Olkiluodontie road, the air conditioning of ONKALO and occasional sources such as springtime bird sounds. Construction activities in the area were seen in increased amount of NO 3 -N in the bulk deposition, and Al and Fe accumulating on needle surfaces in areas close to the rock piling and crushing area. Scots

  8. Results of monitoring at Olkiluoto in 2012. Environment

    Energy Technology Data Exchange (ETDEWEB)

    Haapanen, A. (ed.) [Haapanen Forest Consulting, Vanhakylae (Finland)

    2014-04-15

    In 2003, Posiva Oy presented a programme for monitoring at Olkiluoto during construction and operation of ONKALO. In 2012 the monitoring programme was updated to concern the years 2012-2018. Part of the monitoring is performed by the company running the nuclear power plants on the island, Teollisuuden Voima Oy (TVO). This Working Report presents the main results of Posiva's environmental monitoring programme on Olkiluoto Island in 2012. Results are presented under five topics: 1. Evolution of geosphere, 2. Biosphere modelling input data, 3. Interaction between surface environment and groundwater in bedrock, 4. Environmental impact and 5. Baseline of monitoring of radioactive releases. Concerning the evolution of geosphere, LIDAR-scannings were done in the Olkiluoto area in 2012. The acquired data can be used for elevation and other modelling purposes. The soil solution quality in 2012 was quite comparable to that in earlier years. Proximity of the sea and the young age of soils are seen in soil solution results. Biosphere modelling input data in 2012 included e.g. continuous tree litterfall and transpiration data, as well as updated game statistics and population estimates of fauna, a fishery survey from the River Eurajoki (2011) and basic monitoring data from Olkiluoto offshore properties. Interaction between surface environment and groundwater in bedrock includes e.g. weather and surface water monitoring data. Environmental impact analyses included e.g. monitoring of noise, air quality, effluent waters and private drilled wells. Noise monitoring in the vicinity of ONKALO showed that in the case of raised noise levels the sources are mainly the traffic on Olkiluodontie road, the air conditioning of ONKALO and occasional sources such as springtime bird sounds. Construction activities in the area were seen in increased amount of NO{sub 3}-N in the bulk deposition, and Al and Fe accumulating on needle surfaces in areas close to the rock piling and crushing area

  9. Meteorological data at Olkiluoto in period of 2002-2004

    International Nuclear Information System (INIS)

    Ikonen, A.T.

    2005-07-01

    In this working report the data of some routine field observations of Posiva Oy and automatic measurements of the Olkiluoto nuclear power plant weather station owned and operated by Teollisuuden Voima Oy is published for further reference. The data reported here covers observations from 2002 to 2004. First, a concise description of data acquisition methods and handling is provided. Thereafter the actual data is presented in the appendices. Weather measurements (e.g. temperature, wind speed and direction, humidity) and snow, ground frost and ditch flow rate observations are reported. (orig.)

  10. Game statistics for the island of Olkiluoto in 2005-2006

    International Nuclear Information System (INIS)

    Oja, S.

    2006-11-01

    The game statistics for the island of Olkiluoto was updated in February 2006. The estimate of game populations in Olkiluoto was done on the basis of interviews of local hunters and available statistical materials. The collected data were compared to earlier studies of game animals done in Olkiluoto. The populations of Elk and White-tailed Deer are stable, and the population of Roe Deer is increasing significantly. The populations of small mammal predators (American Mink, Raccoon Dog, Red Fox) are very high level, despite of intensive hunting. Other game animals like waterfowls are hunted moderately and the amount of catches are small. (orig.)

  11. Nuclear energy in Finland

    International Nuclear Information System (INIS)

    2011-01-01

    The purpose of the booklet is to provide an up-to-date overview of the use of nuclear energy in Finland as well as future plans regarding the nuclear energy sector. It is intended for people working in the nuclear energy or other energy sectors in other countries, as well as for those international audiences and decision-makers who would like to have extra information on this particular energy sector. Nuclear energy is described as part of the Finnish electricity market. (orig.)

  12. Case study in Finland

    International Nuclear Information System (INIS)

    Santaholma, J.

    1993-01-01

    The Nuclear Energy act of Finland 1988 provides for the permits and licenses (decision in principle by the government on a new nuclear power plant-project, construction permit by the government, fuel permits by the Ministry of Trade and Industry, operating license by the government) for major nuclear installations. Political consideration from the point of view of the general interest of the society is made by the Government in the decision in Principle. If the decision in Principle is positive, it is subject to ratification by the parliament. In other words, democracy through representation, but not through referendum, is applied

  13. Greenland Analogue Project - Hydraulic properties of deformation zones and fracture domains at Forsmark, Laxemar and Olkiluoto for usage together with Geomodel version 1

    International Nuclear Information System (INIS)

    Follin, Sven; Stigsson, Martin; Rhen, Ingvar; Engstroem, Jon; Klint, Knut Erik

    2011-05-01

    The database of the GAP site is under development. In order to meet the data needs of the different modelling teams working with groundwater flow modelling it has been decided to compile trial data sets comprising structural-hydraulic properties suitable for flow modelling on different scales. The properties provided in this report are based on data and groundwater flow modelling studies conducted for three sites located in the Fennoscandian Shield, two of which are studied by SKB, Forsmark and Laxemar, and one by Posiva, Olkiluoto. The provided hydraulic properties provided here are simplified to facilitate a readily usage together with the GAP Geomodel version 1

  14. Greenland Analogue Project - Hydraulic properties of deformation zones and fracture domains at Forsmark, Laxemar and Olkiluoto for usage together with Geomodel version 1

    Energy Technology Data Exchange (ETDEWEB)

    Follin, Sven (SF GeoLogic AB (Sweden)); Stigsson, Martin (Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)); Rhen, Ingvar (Sweco Environment AB (Sweden)); Engstroem, Jon (Geologian tutkimuskeskus (Finland)); Klint, Knut Erik (De Nationale Geologiske Undersoegelser for Danmark og Groenland (Denmark))

    2011-05-15

    The database of the GAP site is under development. In order to meet the data needs of the different modelling teams working with groundwater flow modelling it has been decided to compile trial data sets comprising structural-hydraulic properties suitable for flow modelling on different scales. The properties provided in this report are based on data and groundwater flow modelling studies conducted for three sites located in the Fennoscandian Shield, two of which are studied by SKB, Forsmark and Laxemar, and one by Posiva, Olkiluoto. The provided hydraulic properties provided here are simplified to facilitate a readily usage together with the GAP Geomodel version 1.

  15. Deep Time Iterations: Familiarity, Horizons, and Pattern among Finland's Nuclear Waste Safety Experts

    Science.gov (United States)

    Ialenti, Vincent Francis

    This ethnography reconsiders nuclear waste risk's deep time horizons' often-sensationalized aesthetics of horror, sublimity, and awe. It does so by tracking how Finland's nuclear energy and waste experts made visions of distant future Finlands<