WorldWideScience

Sample records for oled device architecture

  1. Enhanced performance of organic light-emitting diodes (OLEDs) and OLED-based photoluminescent sensing platforms by novel microstructures and device architectures

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Rui [Ames Lab., Ames, IA (United States)

    2012-01-01

    After a general introduction to OLEDs and OLED-based PL sensors, the transient emission mechanism of guest-host OLEDs is described both experimentally and theoretically. A monolithic and easy-to-apply process is demonstrated for fabricating multicolor microcavity OLEDs (that improve the sensor platform). The outcoupling issues of OLEDs at the substrate/air interface are addressed by using a microstructured polymer film resulting from a PS and polyethylene glycol (PEG) mixture. Based on the understanding of OLEDs and their improvement, research was done in order to realize integrated all organic-based O2 and pH sensors with improved signal intensity and sensitivity. The sensor design modification and optimization are summarized

  2. Improved multilayer OLED architecture using evolutionary genetic algorithm

    International Nuclear Information System (INIS)

    Quirino, W.G.; Teixeira, K.C.; Legnani, C.; Calil, V.L.; Messer, B.; Neto, O.P. Vilela; Pacheco, M.A.C.; Cremona, M.

    2009-01-01

    Organic light-emitting diodes (OLEDs) constitute a new class of emissive devices, which present high efficiency and low voltage operation, among other advantages over current technology. Multilayer architecture (M-OLED) is generally used to optimize these devices, specially overcoming the suppression of light emission due to the exciton recombination near the metal layers. However, improvement in recombination, transport and charge injection can also be achieved by blending electron and hole transporting layers into the same one. Graded emissive region devices can provide promising results regarding quantum and power efficiency and brightness, as well. The massive number of possible model configurations, however, suggests that a search algorithm would be more suitable for this matter. In this work, multilayer OLEDs were simulated and fabricated using Genetic Algorithms (GAs) as evolutionary strategy to improve their efficiency. Genetic Algorithms are stochastic algorithms based on genetic inheritance and Darwinian strife to survival. In our simulations, it was assumed a 50 nm width graded region, divided into five equally sized layers. The relative concentrations of the materials within each layer were optimized to obtain the lower V/J 0.5 ratio, where V is the applied voltage and J the current density. The best M-OLED architecture obtained by genetic algorithm presented a V/J 0.5 ratio nearly 7% lower than the value reported in the literature. In order to check the experimental validity of the improved results obtained in the simulations, two M-OLEDs with different architectures were fabricated by thermal deposition in high vacuum environment. The results of the comparison between simulation and some experiments are presented and discussed.

  3. Kirigami-based three-dimensional OLED concepts for architectural lighting

    Science.gov (United States)

    Kim, Taehwan; Price, Jared S.; Grede, Alex; Lee, Sora; Jackson, Thomas N.; Giebink, Noel C.

    2017-08-01

    Dramatic improvements in white organic light emitting diode (OLED) performance and lifetime over the past decade are driving commercialization of this technology for solid-state lighting applications. As white OLEDs attempt to gain a foothold in the market, however, the biggest challenge outside of lowering their manufacturing cost arguably now lies in creating an architecturally adaptable form factor that will drive public adoption and differentiate OLED lighting from established LED products. Here, we present concepts based on kirigami (the Japanese art of paper cutting and folding) that enable intricate three-dimensional (3D) OLED lighting structures from two dimensional layouts. Using an ultraflexible, encapsulated OLED device architecture on 25 60 μm thick clear polyimide film substrate with simple cut and fold patterns, we demonstrate a series of different lighting concepts ranging from a simple `pop up' structure to more complex designs such as stretchable window blind-like panel, candle flame, and multi-element globe lamp. We only find slight degradation in OLED electrical performance when these designs are shaped into 3D. Our results point to an alternate paradigm for OLED lighting that moves beyond traditional 2D panels toward 3D designs that deliver unique and creative new opportunities for lighting.

  4. Organic light-emitting devices (OLEDs) and OLED-based chemical and biological sensors: an overview

    Energy Technology Data Exchange (ETDEWEB)

    Shinar, Joseph [Ames Laboratory-USDOE and Department of Physics and Astronomy, Iowa State University, Ames, IA 50011 (United States); Shinar, Ruth [Microelectronics Research Center, Iowa State University, Ames, IA 50011 (United States)

    2008-07-07

    The basic photophysics, transport properties, state of the art, and challenges in OLED science and technology, and the major developments in structurally integrated OLED-based luminescent chemical and biological sensors are reviewed briefly. The dramatic advances in OLED performance have resulted in devices with projected continuous operating lifetimes of {approx}2 x 10{sup 5} h ({approx}23 yr) at {approx}150 Cd m{sup -2} (the typical brightness of a computer monitor or TV). Consequently, commercial products incorporating OLEDs, e.g., cell phones, MP3 players, and, most recently, OLED TVs, are rapidly proliferating. The progress in elucidating the photophysics and transport properties, occurring in tandem with the development of OLEDs, has been no less dramatic. It has resulted in a detailed understanding of the dynamics of trapped and mobile negative and positive polarons (to which the electrons and holes, respectively, relax upon injection), and of singlet and triplet excitons. It has also yielded a detailed understanding of the spin dynamics of polarons and triplet excitons, which affects their overall dynamics significantly. Despite the aforementioned progress, there are outstanding challenges in OLED science and technology, notably in improving the efficiency of the devices and their stability at high brightness (>1000 Cd m{sup -2}). One of the most recent emerging OLED-based technologies is that of structurally integrated photoluminescence-based chemical and biological sensors. This sensor platform, pioneered by the authors, yields uniquely simple and potentially very low-cost sensor (micro)arrays. The second part of this review describes the recent developments in implementing this platform for gas phase oxygen, dissolved oxygen (DO), anthrax lethal factor, and hydrazine sensors, and for a DO, glucose, lactate, and ethanol multianalyte sensor. (topical review)

  5. Organic light-emitting devices (OLEDs) and OLED-based chemical and biological sensors: an overview

    International Nuclear Information System (INIS)

    Shinar, Joseph; Shinar, Ruth

    2008-01-01

    The basic photophysics, transport properties, state of the art, and challenges in OLED science and technology, and the major developments in structurally integrated OLED-based luminescent chemical and biological sensors are reviewed briefly. The dramatic advances in OLED performance have resulted in devices with projected continuous operating lifetimes of ∼2 x 10 5 h (∼23 yr) at ∼150 Cd m -2 (the typical brightness of a computer monitor or TV). Consequently, commercial products incorporating OLEDs, e.g., cell phones, MP3 players, and, most recently, OLED TVs, are rapidly proliferating. The progress in elucidating the photophysics and transport properties, occurring in tandem with the development of OLEDs, has been no less dramatic. It has resulted in a detailed understanding of the dynamics of trapped and mobile negative and positive polarons (to which the electrons and holes, respectively, relax upon injection), and of singlet and triplet excitons. It has also yielded a detailed understanding of the spin dynamics of polarons and triplet excitons, which affects their overall dynamics significantly. Despite the aforementioned progress, there are outstanding challenges in OLED science and technology, notably in improving the efficiency of the devices and their stability at high brightness (>1000 Cd m -2 ). One of the most recent emerging OLED-based technologies is that of structurally integrated photoluminescence-based chemical and biological sensors. This sensor platform, pioneered by the authors, yields uniquely simple and potentially very low-cost sensor (micro)arrays. The second part of this review describes the recent developments in implementing this platform for gas phase oxygen, dissolved oxygen (DO), anthrax lethal factor, and hydrazine sensors, and for a DO, glucose, lactate, and ethanol multianalyte sensor. (topical review)

  6. Progress of OLED devices with high efficiency at high luminance

    Science.gov (United States)

    Nguyen, Carmen; Ingram, Grayson; Lu, Zhenghong

    2014-03-01

    Organic light emitting diodes (OLEDs) have progressed significantly over the last two decades. For years, OLEDs have been promoted as the next generation technology for flat panel displays and solid-state lighting due to their potential for high energy efficiency and dynamic range of colors. Although high efficiency can readily be obtained at low brightness levels, a significant decline at high brightness is commonly observed. In this report, we will review various strategies for achieving highly efficient phosphorescent OLED devices at high luminance. Specifically, we will provide details regarding the performance and general working principles behind each strategy. We will conclude by looking at how some of these strategies can be combined to produce high efficiency white OLEDs at high brightness.

  7. Prevention of short circuits in solution-processed OLED devices

    NARCIS (Netherlands)

    Jolt Oostra, A.; Blom, P.W.M.; Michels, J.J.

    2014-01-01

    Pinholes in the emitting layer of an organic light emitting diode (OLED), e.g. induced by particle contamination or processing flaws, lead to direct contact between the hole-injection layer (HIL) and the cathode. The resulting short circuits give rise to catastrophic device failure. We demonstrate

  8. Solution processed, white emitting tandem organic light-emitting diodes with inverted device architecture.

    Science.gov (United States)

    Höfle, Stefan; Schienle, Alexander; Bernhard, Christoph; Bruns, Michael; Lemmer, Uli; Colsmann, Alexander

    2014-08-13

    Fully solution processed monochromatic and white-light emitting tandem or multi-photon polymer OLEDs with an inverted device architecture have been realized by employing WO3 /PEDOT:PSS/ZnO/PEI charge carrier generation layers. The luminance of the sub-OLEDs adds up in the stacked device indicating multi-photon emission. The white OLEDs exhibit a CRI of 75. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. Making Image More Energy Efficient for OLED Smart Devices

    Directory of Open Access Journals (Sweden)

    Deguang Li

    2016-01-01

    Full Text Available Now, more and more mobile smart devices are emerging massively; energy consumption of these devices has become an important consideration due to the limitation of battery capacity. Displays are the dominant energy consuming component of battery-operated devices, giving rise to organic light-emitting diode (OLED as a new promising display technology, which consumes different power when displaying different content due to their emissive nature. Based on this property, we propose an approach to improve image energy efficiency on OLED displays by perceiving image content. The key idea of our approach is to eliminate undesired details while preserving the region of interest of the image by leveraging the color and spatial information. First, we use edge detection algorithm to extract region of interest (ROI of an image. Next, we gradually change luminance and saturation of region of noninterest (NON-ROI of the image. Then we perform detailed experiment and case study to validate our approach; experiment results show that our approach can save 22.5% energy on average while preserving high quality of the image.

  10. Doping chloro boron subnaphthalocyanines and chloro boron subphthalocyanine in simple OLED architectures yields warm white incandescent-like emissions

    Science.gov (United States)

    Plint, Trevor G.; Lessard, Benoît H.; Bender, Timothy P.

    2018-01-01

    We have incorporated chloro boron subphthalocyanine (Cl-BsubPc) and chloro boron subnapthalocyanines (Cl-ClnBsubNcs) into organic light emitting diodes (OLEDs) that enabled an overall warm white emission with CIE coordinates close to that of a 60 W incandescent lightbulb. More specifically, we have shown that Cl-BsubPc and Cl-ClnBsubNcs can be used as dopant emitters in a simple host-dopant architecture, and we have compared the use of NPB and Alq3 as potential hosts for these materials. When doped into Alq3, Cl-BsubPc shows a strong orange emission, and Cl-ClnBsubNcs shows a moderately strong red emission. We have further demonstrated that Cl-BsubPc and Cl-ClnBsubNcs can be co-doped into the same layer giving combined orange and red emission peaks. A "cascade" energy transfer mechanism of sequential absorption and re-emission is proposed. Device performance characteristics such as luminance, current efficiency, photoluminescence efficiency, and external quantum efficiency are tabulated. Additionally, in view of ongoing research into white emitting OLEDs for indoor lighting purposes, the Colour Rendering Index (CRI), R9 values, and CIE co-ordinates for these devices are also discussed. We conclude from this study that the BsubNc chromophore has potential application as a red dopant in OLEDs including for indoor lighting. Additionally, given the scope for axial and peripheral derivatization of the BsubNc motif, we believe that this chromophore has many unexplored molecular design handles that will affect its ultimate performance and application in OLEDs and other opto-electronic devices.

  11. Degradation of OLEDs devices: study methods and solutions

    OpenAIRE

    Santoro, Elena

    2016-01-01

    2014 - 2015 The fast technological evolution of our world requests the necessity to make this development sustainable. In order to achieve this goal more relevance has been given to the energy consumption and environmental impact of the modern society consumerism. These considerations point out the need to increase the effort in research of unconventional materials, new concept and system architecture for devices that could help to overcome these challenges. Nanotechnologies offer th...

  12. Charge generation layers for solution processed tandem organic light emitting diodes with regular device architecture.

    Science.gov (United States)

    Höfle, Stefan; Bernhard, Christoph; Bruns, Michael; Kübel, Christian; Scherer, Torsten; Lemmer, Uli; Colsmann, Alexander

    2015-04-22

    Tandem organic light emitting diodes (OLEDs) utilizing fluorescent polymers in both sub-OLEDs and a regular device architecture were fabricated from solution, and their structure and performance characterized. The charge carrier generation layer comprised a zinc oxide layer, modified by a polyethylenimine interface dipole, for electron injection and either MoO3, WO3, or VOx for hole injection into the adjacent sub-OLEDs. ToF-SIMS investigations and STEM-EDX mapping verified the distinct functional layers throughout the layer stack. At a given device current density, the current efficiencies of both sub-OLEDs add up to a maximum of 25 cd/A, indicating a properly working tandem OLED.

  13. White OLED devices and processes for lighting applications

    Science.gov (United States)

    Ide, Nobuhiro; Tsuji, Hiroya; Ito, Norihiro; Matsuhisa, Yuko; Houzumi, Shingo; Nishimori, Taisuke

    2010-05-01

    In these days, the basic performances of white OLEDs are dramatically improved and application of OLEDs to "Lighting" is expected to be true in the near future. We have developed various technologies for OLED lighting with the aid of the Japanese governmental project, "High-efficiency lighting based on the organic light-emitting mechanism." In this project, a white OLED with high efficiency (37 lm/W) and high quality emission characteristics (CRI of 95 with a small variation of chromaticity in different directions and chromaticity just on the black-body radiation curve) applicable to "Lighting" was realized by a two-unit structure with a fluorescent deep blue emissive unit and a phosphorescent green and red emissive unit. Half-decay lifetime of this white OLED at 1,000 cd/m2 was over 40,000 h. A heat radiative, thin encapsulation structure (less than 1 mm) realized a very stable emission at high luminance of over 3,000 cd/m2. A new deposition source with a hot-wall and a rate controllable valve was developed. Thickness uniformity within +/- 3% at high deposition rate of over 8 nm/s, high material utilization of over 70 %, and repeatable deposition rate controllability were confirmed.

  14. Low cost UV-Ozone reactor mounted for treatment of electrode anodes used in P-OLEDs devices

    Directory of Open Access Journals (Sweden)

    Emerson Roberto Santos

    Full Text Available Abstract Low cost UV-Ozone reactor using a high pressure mercury vapor lamp of 80 watts without outer bulb showed good results for treatment of ITO films used as anode electrode in the assembly of P-OLED (polymer-organic light emitting diode devices. This study revealed 20 minutes as effective treatment time and it was verified also that the effect of UV-Ozone treatment loses its efficiency as the elapsed time increases. It was analyzed with measurements of contact angle using a droplet of PEDOT:PSS polymer. P-OLEDs devices were mounted with architecture: ITO/PEDOT:PSS/PVK/Alq3/Al. The PVK polymer was diluted in organic solvent of 1,2,4-trichlorobenzene with concentrations of: 5, 10, 20 and 30 mg/mL. Results revealed better performance of P-OLED devices for concentration of 5 mg/mL resulting in lower threshold voltage, elevation of electrical current and similar diode curve.

  15. OLED Fundamentals: Materials, Devices, and Processing of Organic Light-Emitting Diodes

    Energy Technology Data Exchange (ETDEWEB)

    Blochwitz-Nimoth, Jan; Bhandari, Abhinav; Boesch, Damien; Fincher, Curtis R.; Gaspar, Daniel J.; Gotthold, David W.; Greiner, Mark T.; Kido, Junji; Kondakov, Denis; Korotkov, Roman; Krylova, Valentina A.; Loeser, Falk; Lu, Min-Hao; Lu, Zheng-Hong; Lussem, Bjorn; Moro, Lorenza; Padmaperuma, Asanga B.; Polikarpov, Evgueni; Rostovtsev, Vsevolod V.; Sasabe, Hisahiro; Silverman, Gary; Thompson, Mark E.; Tietze, Max; Tyan, Yuan-Sheng; Weaver, Michael; Xin , Xu; Zeng, Xianghui

    2015-05-26

    What is an organic light emitting diode (OLED)? Why should we care? What are they made of? How are they made? What are the challenges in seeing these devices enter the marketplace in various applications? These are the questions we hope to answer in this book, at a level suitable for knowledgeable non-experts, graduate students and scientists and engineers working in the field who want to understand the broader context of their work. At the most basic level, an OLED is a promising new technology composed of some organic material sandwiched between two electrodes. When current is passed through the device, light is emitted. The stack of layers can be very thin and has many variations, including flexible and/or transparent. The organic material can be polymeric or composed small molecules, and may include inorganic components. The electrodes may consist of metals, metal oxides, carbon nanomaterials, or other species, though of course for light to be emitted, one electrode must be transparent. OLEDs may be fabricated on glass, metal foils, or polymer sheets (though polymeric substrates must be modified to protect the organic material from moisture or oxygen). In any event, the organic material must be protected from moisture during storage and operation. A control circuit, the exact nature of which depends on the application, drives the OLED. Nevertheless, the control circuit should have very stable current control to generate uniform light emission. OLEDs can be designed to emit a single color of light, white light, or even tunable colors. The devices can be switched on and off very rapidly, which makes them suitable for displays or for general lighting. Given the amazing complexity of the technical and design challenges for practical OLED applications, it is not surprising that applications are still somewhat limited. Although organic electroluminescence is more than 50 years old, the modern OLED field is really only about half that age – with the first high

  16. OLEDs for lighting: new approaches

    Science.gov (United States)

    Duggal, Anil R.; Foust, Donald F.; Nealon, William F.; Heller, Christian M.

    2004-02-01

    OLED technology has improved to the point where it is now possible to envision developing OLEDs as a low cost solid state light source. In order to realize this, significant advances have to be made in device efficiency, lifetime at high brightness, high throughput fabrication, and the generation of illumination quality white light. In this talk, the requirements for general lighting will be reviewed and various approaches to meeting them will be outlined. Emphasis will be placed on a new monolithic series-connected OLED design architecture that promises scalability without high fabrication cost or design complexity.

  17. Compressed optimization of device architectures

    Energy Technology Data Exchange (ETDEWEB)

    Frees, Adam [Univ. of Wisconsin, Madison, WI (United States). Dept. of Physics; Gamble, John King [Microsoft Research, Redmond, WA (United States). Quantum Architectures and Computation Group; Ward, Daniel Robert [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States). Center for Computing Research; Blume-Kohout, Robin J [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States). Center for Computing Research; Eriksson, M. A. [Univ. of Wisconsin, Madison, WI (United States). Dept. of Physics; Friesen, Mark [Univ. of Wisconsin, Madison, WI (United States). Dept. of Physics; Coppersmith, Susan N. [Univ. of Wisconsin, Madison, WI (United States). Dept. of Physics

    2014-09-01

    Recent advances in nanotechnology have enabled researchers to control individual quantum mechanical objects with unprecedented accuracy, opening the door for both quantum and extreme- scale conventional computation applications. As these devices become more complex, designing for facility of control becomes a daunting and computationally infeasible task. Here, motivated by ideas from compressed sensing, we introduce a protocol for the Compressed Optimization of Device Architectures (CODA). It leads naturally to a metric for benchmarking and optimizing device designs, as well as an automatic device control protocol that reduces the operational complexity required to achieve a particular output. Because this protocol is both experimentally and computationally efficient, it is readily extensible to large systems. For this paper, we demonstrate both the bench- marking and device control protocol components of CODA through examples of realistic simulations of electrostatic quantum dot devices, which are currently being developed experimentally for quantum computation.

  18. Study of organic light emitting devices (OLEDs) with optimal emission efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Jai [School of Engineering and IT, B-purple 12, Faculty of EHS, Charles Darwin University, Darwin, NT 0909 (Australia)

    2010-04-15

    The external emission efficiency of organic light emitting devices (OLEDs) is analysed by studying the rate of spontaneous emission of both singlet and triplet excitons and their corresponding radiative lifetimes. Rates of spontaneous emissions are calculated from the first order perturbation theory using the newly discovered time-dependent spin-orbit-exciton-photon interaction operator as the perturbation operator. It is clearly shown how the new interaction operator is responsible for attracting triplet excitons to a phosphor (heavy metal atom) and then it flips the spins to a singlet configuration. Thus, the spin forbidden transition becomes spin allowed. Calculated rates agree with the experimental results qualitatively. Results are of general interests for OLED studies. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  19. OLED displays and lighting

    CERN Document Server

    Koden, Mitsuhiro

    2017-01-01

    Organic light-emitting diodes (OLEDs) have emerged as the leading technology for the new display and lighting market. OLEDs are solid-state devices composed of thin films of organic molecules that create light with the application of electricity. OLEDs can provide brighter, crisper displays on electronic devices and use less power than conventional light-emitting diodes (LEDs) or liquid crystal displays (LCDs) used today. This book covers both the fundamentals and practical applications of flat and flexible OLEDs.

  20. OLED Lighting Products: Capabilities, Challenges, Potential

    Energy Technology Data Exchange (ETDEWEB)

    Miller, N. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Leon, F. A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-05-31

    A report that focuses on the potential for architectural OLED lighting – describing currently available OLED products as well as promised improvements, and addressing the technology and market hurdles that have thus far prevented wider use of OLEDs.

  1. Enhanced device performances of a new inverted top-emitting OLEDs with relatively thick Ag electrode.

    Science.gov (United States)

    Park, So-Ra; Suh, Min Chul

    2018-02-19

    To improve the device performances of top-emitting organic light emitting diodes (TEOLEDs), we developed a new inverted TEOLEDs structure with silver (Ag) metal as a semi-transparent top electrode. Especially, we found that the use of relatively thick Ag electrode without using any carrier injection layer is beneficial to realize highly efficient device performances. Also, we could insert very thick overlying hole transport layer (HTL) on the emitting layer (EML) which could be very helpful to suppress the surface plasmon polariton (SPP) coupling if it is applied to the common bottom-emission OLEDs (BEOLEDs). As a result, we could realize noteworthy high current efficiency of approximately ~188.1 cd/A in our new inverted TEOLEDs with 25 nm thick Ag electrode.

  2. An architecture for device independent interfacing

    International Nuclear Information System (INIS)

    Pace, D.M.

    1990-01-01

    Achieving device independence for software applications is required for all but a small number of critical real time applications. Device independence is achieved by establishing protocols and building protocol interpreters for the specific devices. Data structures containing pointers to functions provide a flexible architecture for implementing protocol translation. 3 refs., 5 figs

  3. Flexible devices: from materials, architectures to applications

    Science.gov (United States)

    Zou, Mingzhi; Ma, Yue; Yuan, Xin; Hu, Yi; Liu, Jie; Jin, Zhong

    2018-01-01

    Flexible devices, such as flexible electronic devices and flexible energy storage devices, have attracted a significant amount of attention in recent years for their potential applications in modern human lives. The development of flexible devices is moving forward rapidly, as the innovation of methods and manufacturing processes has greatly encouraged the research of flexible devices. This review focuses on advanced materials, architecture designs and abundant applications of flexible devices, and discusses the problems and challenges in current situations of flexible devices. We summarize the discovery of novel materials and the design of new architectures for improving the performance of flexible devices. Finally, we introduce the applications of flexible devices as key components in real life. Project supported by the National Key R&D Program of China (Nos. 2017YFA0208200, 2016YFB0700600, 2015CB659300), the National Natural Science Foundation of China (Nos. 21403105, 21573108), and the Fundamental Research Funds for the Central Universities (No. 020514380107).

  4. Device reflectivity as a simple rule for predicting the suitability of scattering foils for improved OLED light extraction

    NARCIS (Netherlands)

    Levell, J.W.; Harkema, S.; Pendyala, R.K.; Rensing, P.A.; Senes, A.; Bollen, D.; MacKerron, D.; Wilson, J.S.

    2013-01-01

    A general challenge in Organic Light Emitting Diodes (OLEDs) is to extract the light efficiently from waveguided modes within the device structure. This can be accomplished by applying an additional scattering layer to the substrate which results in outcoupling increases between 0% to <100% in

  5. Web Service Architecture Framework for Embedded Devices

    Science.gov (United States)

    Yanzick, Paul David

    2009-01-01

    The use of Service Oriented Architectures, namely web services, has become a widely adopted method for transfer of data between systems across the Internet as well as the Enterprise. Adopting a similar approach to embedded devices is also starting to emerge as personal devices and sensor networks are becoming more common in the industry. This…

  6. Recent progress in OLED and flexible displays and their potential for application to aerospace and military display systems

    Science.gov (United States)

    Sarma, Kalluri

    2015-05-01

    Organic light emitting diode (OLED) display technology has advanced significantly in recent years and it is increasingly being adapted in consumer electronics products with premium performance, such as high resolution smart phones, Tablet PCs and TVs. Even flexible OLED displays are beginning to be commercialized in consumer electronic devices such as smart phones and smart watches. In addition to the advances in OLED emitters, successful development and adoption of OLED displays for premium performance applications relies on the advances in several enabling technologies including TFT backplanes, pixel drive electronics, pixel patterning technologies, encapsulation technologies and system level engineering. In this paper we will discuss the impact of the recent advances in LTPS and AOS TFTs, R, G, B and White OLED with color filter pixel architectures, and encapsulation, on the success of the OLEDs in consumer electronic devices. We will then discuss potential of these advances in addressing the requirements of OLED and flexible displays for the military and avionics applications.

  7. Trends in Microfabrication Capabilities & Device Architectures.

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, Todd [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jones, Adam [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Lentine, Tony [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Mudrick, John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Okandan, Murat [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Rodrigues, Arun [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-06-01

    The last two decades have seen an explosion in worldwide R&D, enabling fundamentally new capabilities while at the same time changing the international technology landscape. The advent of technologies for continued miniaturization and electronics feature size reduction, and for architectural innovations, will have many technical, economic, and national security implications. It is important to anticipate possible microelectronics development directions and their implications on US national interests. This report forecasts and assesses trends and directions for several potentially disruptive microfabrication capabilities and device architectures that may emerge in the next 5-10 years.

  8. Light Management in Flexible OLEDs

    NARCIS (Netherlands)

    Harkema, S.; Pendyala, R.K.; Geurts, C.G.C.; Helgers, P.L.J.; Levell, J.W.; Wilson, J.S.; MacKerron, D.

    2014-01-01

    Organic light-emitting diodes (OLEDs) are a promising lighting technology. In particular OLEDs fabricated on plastic foils are believed to hold the future. These planar devices are subject to various optical losses, which requires sophisticated light management solutions. Flexible OLEDs on plastic

  9. Structurally Integrated Photoluminescence-Based Lactate Sensor Using Organic Light Emitting Devices (OLEDs) as the Light Source

    International Nuclear Information System (INIS)

    Chengliang Qian

    2006-01-01

    Multianalyte bio(chemical) sensors are extensively researched for monitoring analytes in complex systems, such as blood serum. As a step towards developing such multianalyte sensors, we studied a novel, structurally integrated, organic light emitting device (OLED)-based sensing platform for detection of lactate. Lactate biosensors have attracted numerous research efforts, due to their wide applications in clinical diagnosis, athletic training and food industry. The OLED-based sensor is based on monitoring the oxidation reaction of lactate, which is catalyzed by the lactate oxidase (LOX) enzyme. The sensing component is based on an oxygen-sensitive dye, Platinum octaethyl porphyrin (PtOEP), whose photoluminescence (PL) lifetime τ decreases as the oxygen level increases. The PtOEP dye was embedded in a thin film polystyrene (PS) matrix; the LOX was dissolved in solution or immobilized in a sol-gel matrix. τ was measured as a function of the lactate concentration; as the lactate concentration increases, τ increases due to increased oxygen consumption. The sensors performance is discussed in terms of the detection sensitivity, dynamic range, and response time. A response time of ∼32 sec was achieved when the LOX was dissolved in solution and kept in a closed cell. Steps towards development of a multianalyte sensor array using an array of individually addressable OLED pixels were also presented

  10. Structurally Integrated Photoluminescence-Based Lactate Sensor Using Organic Light Emitting Devices (OLEDs) as the Light Source

    Energy Technology Data Exchange (ETDEWEB)

    Qian, Chengliang [Iowa State Univ., Ames, IA (United States)

    2006-01-01

    Multianalyte bio(chemical) sensors are extensively researched for monitoring analytes in complex systems, such as blood serum. As a step towards developing such multianalyte sensors, we studied a novel, structurally integrated, organic light emitting device (OLED)-based sensing platform for detection of lactate. Lactate biosensors have attracted numerous research efforts, due to their wide applications in clinical diagnosis, athletic training and food industry. The OLED-based sensor is based on monitoring the oxidation reaction of lactate, which is catalyzed by the lactate oxidase (LOX) enzyme. The sensing component is based on an oxygen-sensitive dye, Platinum octaethyl porphyrin (PtOEP), whose photoluminescence (PL) lifetime τ decreases as the oxygen level increases. The PtOEP dye was embedded in a thin film polystyrene (PS) matrix; the LOX was dissolved in solution or immobilized in a sol-gel matrix. τ was measured as a function of the lactate concentration; as the lactate concentration increases, τ increases due to increased oxygen consumption. The sensors performance is discussed in terms of the detection sensitivity, dynamic range, and response time. A response time of ~32 sec was achieved when the LOX was dissolved in solution and kept in a closed cell. Steps towards development of a multianalyte sensor array using an array of individually addressable OLED pixels were also presented.

  11. Optical analysis of down-conversion OLEDs

    Science.gov (United States)

    Krummacher, Benjamin; Klein, Markus; von Malm, Norwin; Winnacker, Albrecht

    2008-02-01

    Phosphor down-conversion of blue organic light-emitting diodes (OLEDs) is one approach to generate white light, which offers the possibility of easy color tuning, a simple device architecture and color stability over lifetime. In this article previous work on down-conversion devices in the field of organic solid state lighting is briefly reviewed. Further, bottom emitting down-conversion OLEDs are studied from an optical point of view. Therefore the physical processes occurring in the down-conversion layer are translated into a model which is implemented in a ray tracing simulation. By comparing its predictions to experimental results the model is confirmed. For the experiments a blue-emitting polymer OLED (PLED) panel optically coupled to a series of down-conversion layers is used. Based on results obtained from ray tracing simulation some of the implications of the model for the performance of down-conversion OLEDs are discussed. In particular it is analysed how the effective reflectance of the underlying blue OLED and the particle size distribution of the phosphor powder embedded in the matrix of the down-conversion layer influence extraction efficiency.

  12. Highly efficient phosphorescent blue and white organic light-emitting devices with simplified architectures

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Chih-Hao, E-mail: chc@saturn.yzu.edu.tw [Department of Photonics Engineering, Yuan Ze University, Chung-Li, Taiwan 32003 (China); Ding, Yong-Shung; Hsieh, Po-Wei; Chang, Chien-Ping; Lin, Wei-Chieh [Department of Photonics Engineering, Yuan Ze University, Chung-Li, Taiwan 32003 (China); Chang, Hsin-Hua, E-mail: hhua3@mail.vnu.edu.tw [Department of Electro-Optical Engineering, Vanung University, Chung-Li, Taiwan 32061 (China)

    2011-09-01

    Blue phosphorescent organic light-emitting devices (PhOLEDs) with quantum efficiency close to the theoretical maximum were achieved by utilizing a double-layer architecture. Two wide-triplet-gap materials, 1,3-bis(9-carbazolyl)benzene and 1,3,5-tri[(3-pyridyl)-phen-3-yl]benzene, were employed in the emitting and electron-transport layers respectively. The opposite carrier-transport characteristics of these two materials were leveraged to define the exciton formation zone and thus increase the probability of recombination. The efficiency at practical luminance (100 cd/m{sup 2}) was as high as 20.8%, 47.7 cd/A and 31.2 lm/W, respectively. Furthermore, based on the design concept of this simplified architecture, efficient warmish-white PhOLEDs were developed. Such two-component white organic light-emitting devices exhibited rather stable colors over a wide brightness range and yielded electroluminescence efficiencies of 15.3%, 33.3 cd/A, and 22.7 lm/W in the forward directions.

  13. Highly efficient phosphorescent blue and white organic light-emitting devices with simplified architectures

    International Nuclear Information System (INIS)

    Chang, Chih-Hao; Ding, Yong-Shung; Hsieh, Po-Wei; Chang, Chien-Ping; Lin, Wei-Chieh; Chang, Hsin-Hua

    2011-01-01

    Blue phosphorescent organic light-emitting devices (PhOLEDs) with quantum efficiency close to the theoretical maximum were achieved by utilizing a double-layer architecture. Two wide-triplet-gap materials, 1,3-bis(9-carbazolyl)benzene and 1,3,5-tri[(3-pyridyl)-phen-3-yl]benzene, were employed in the emitting and electron-transport layers respectively. The opposite carrier-transport characteristics of these two materials were leveraged to define the exciton formation zone and thus increase the probability of recombination. The efficiency at practical luminance (100 cd/m 2 ) was as high as 20.8%, 47.7 cd/A and 31.2 lm/W, respectively. Furthermore, based on the design concept of this simplified architecture, efficient warmish-white PhOLEDs were developed. Such two-component white organic light-emitting devices exhibited rather stable colors over a wide brightness range and yielded electroluminescence efficiencies of 15.3%, 33.3 cd/A, and 22.7 lm/W in the forward directions.

  14. Turbocharged molecular discovery of OLED emitters: from high-throughput quantum simulation to highly efficient TADF devices

    Science.gov (United States)

    Gómez-Bombarelli, Rafael; Aguilera-Iparraguirre, Jorge; Hirzel, Timothy D.; Ha, Dong-Gwang; Einzinger, Markus; Wu, Tony; Baldo, Marc A.; Aspuru-Guzik, Alán.

    2016-09-01

    Discovering new OLED emitters requires many experiments to synthesize candidates and test performance in devices. Large scale computer simulation can greatly speed this search process but the problem remains challenging enough that brute force application of massive computing power is not enough to successfully identify novel structures. We report a successful High Throughput Virtual Screening study that leveraged a range of methods to optimize the search process. The generation of candidate structures was constrained to contain combinatorial explosion. Simulations were tuned to the specific problem and calibrated with experimental results. Experimentalists and theorists actively collaborated such that experimental feedback was regularly utilized to update and shape the computational search. Supervised machine learning methods prioritized candidate structures prior to quantum chemistry simulation to prevent wasting compute on likely poor performers. With this combination of techniques, each multiplying the strength of the search, this effort managed to navigate an area of molecular space and identify hundreds of promising OLED candidate structures. An experimentally validated selection of this set shows emitters with external quantum efficiencies as high as 22%.

  15. High Efficiency, Illumination Quality OLEDs for Lighting

    Energy Technology Data Exchange (ETDEWEB)

    Joseph Shiang; James Cella; Kelly Chichak; Anil Duggal; Kevin Janora; Chris Heller; Gautam Parthasarathy; Jeffery Youmans; Joseph Shiang

    2008-03-31

    The goal of the program was to demonstrate a 45 lumen per watt white light device based upon the use of multiple emission colors through the use of solution processing. This performance level is a dramatic extension of the team's previous 15 LPW large area illumination device. The fundamental material system was based upon commercial polymer materials. The team was largely able to achieve these goals, and was able to deliver to DOE a 90 lumen illumination source that had an average performance of 34 LPW a 1000 cd/m{sup 2} with peak performances near 40LPW. The average color temperature is 3200K and the calculated CRI 85. The device operated at a brightness of approximately 1000cd/m{sup 2}. The use of multiple emission colors particularly red and blue, provided additional degrees of design flexibility in achieving white light, but also required the use of a multilayered structure to separate the different recombination zones and prevent interconversion of blue emission to red emission. The use of commercial materials had the advantage that improvements by the chemical manufacturers in charge transport efficiency, operating life and material purity could be rapidly incorporated without the expenditure of additional effort. The program was designed to take maximum advantage of the known characteristics of these material and proceeded in seven steps. (1) Identify the most promising materials, (2) assemble them into multi-layer structures to control excitation and transport within the OLED, (3) identify materials development needs that would optimize performance within multilayer structures, (4) build a prototype that demonstrates the potential entitlement of the novel multilayer OLED architecture (5) integrate all of the developments to find the single best materials set to implement the novel multilayer architecture, (6) further optimize the best materials set, (7) make a large area high illumination quality white OLED. A photo of the final deliverable is shown

  16. Oles Have

    DEFF Research Database (Denmark)

    Boris, Stefan Darlan

    2015-01-01

    Landskabsarkitekts Ole Mouritsens Have Tjørnegaard er fotograferet gennem et år af Stefan Darlan Boris. Fotografierne er ledsaget af teksten Vejrhaven.......Landskabsarkitekts Ole Mouritsens Have Tjørnegaard er fotograferet gennem et år af Stefan Darlan Boris. Fotografierne er ledsaget af teksten Vejrhaven....

  17. Light management in flexible OLEDs

    Science.gov (United States)

    Harkema, Stephan; Pendyala, Raghu K.; Geurts, Christian G. C.; Helgers, Paul L. J.; Levell, Jack W.; Wilson, Joanne S.; MacKerron, Duncan

    2014-10-01

    Organic light-emitting diodes (OLEDs) are a promising lighting technology. In particular OLEDs fabricated on plastic foils are believed to hold the future. These planar devices are subject to various optical losses, which requires sophisticated light management solutions. Flexible OLEDs on plastic substrates are as prone to losses related to wave guiding as devices on glass. However, we determined that OLEDs on plastic substrates are susceptible to another loss mode due to wave guiding in the thin film barrier. With modeling of white polymer OLEDs fabricated on PEN substrates, we demonstrate that this loss mode is particularly sensitive to polarized light emission. Furthermore, we investigated how thin film barrier approaches can be combined with high index light extraction layers. Our analysis shows that OLEDs with a thin film barrier consisting of an inorganic/organic/inorganic layer sequence, a low index inorganic negatively affects the OLED efficiency. We conclude that high index inorganics are more suitable for usage in high efficiency flexible OLEDs.

  18. On the Properties and Design of Organic Light-Emitting Devices

    Science.gov (United States)

    Erickson, Nicholas C.

    Organic light-emitting devices (OLEDs) are attractive for use in next-generation display and lighting technologies. In display applications, OLEDs offer a wide emission color gamut, compatibility with flexible substrates, and high power efficiencies. In lighting applications, OLEDs offer attractive features such as broadband emission, high-performance, and potential compatibility with low-cost manufacturing methods. Despite recent demonstrations of near unity internal quantum efficiencies (photons out per electron in), OLED adoption lags conventional technologies, particularly in large-area displays and general lighting applications. This thesis seeks to understand the optical and electronic properties of OLED materials and device architectures which lead to not only high peak efficiency, but also reduced device complexity, high efficiency under high excitation, and optimal white-light emission. This is accomplished through the careful manipulation of organic thin film compositions fabricated via vacuum thermal evaporation, and the introduction of a novel device architecture, the graded-emissive layer (G-EML). This device architecture offers a unique platform to study the electronic properties of varying compositions of organic semiconductors and the resulting device performance. This thesis also introduces an experimental technique to measure the spatial overlap of electrons and holes within an OLED's emissive layer. This overlap is an important parameter which is affected by the choice of materials and device design, and greatly impacts the operation of the OLED at high excitation densities. Using the G-EML device architecture, OLEDs with improved efficiency characteristics are demonstrated, achieving simultaneously high brightness and high efficiency.

  19. On the impact of medical device regulations on software architecture

    DEFF Research Database (Denmark)

    Hansen, Klaus Marius; Manikas, Konstantinos

    2016-01-01

    Compliance to regulations and regulatory approval are requirements for many medical device software systems. In this paper, we investigate the implications of medical device software regulations to the design of software systems. We do so by focusing on the American and European regulatory author...... of the device. Moreover, we review software modularity in the implementation of software medical device and propose a set of preliminary principles for architectural design of software medical device based on a set of constrains identified from the reviewed regulations....

  20. OLEDs for lighting

    Science.gov (United States)

    Boerner, Herbert

    2006-04-01

    Today, organic light emitting diodes are used in small to medium displays in portable electronic equipment like MP3 players and mobile phones. Their thin form factor, together with good readability due to low angular dependence of the emission makes them attractive for these applications. The rapid progress in the last years has lifted the performance of OLEDs to a level where one can seriously start to consider applications in lighting markets. Whereas it is obvious that first applications will be in less demanding niche markets, clearly the most interesting target is the general illumination market. In this report, first applications requirements will be described, followed by a brief review of state of the art monochrome OLEDs. The main part deals with the various ways in which monochrome devices can be combined into white ones, giving examples of existing solutions. The conclusion is that for the white OLED design, there no clear winner yet. Given the rapid progress in material and device development, one can expect that within a few years white OLEDs will be available which can start to penetrate the general lighting market.

  1. Architectures for Improved Organic Semiconductor Devices

    Science.gov (United States)

    Beck, Jonathan H.

    Advancements in the microelectronics industry have brought increasing performance and decreasing prices to a wide range of users. Conventional silicon-based electronics have followed Moore's law to provide an ever-increasing integrated circuit transistor density, which drives processing power, solid-state memory density, and sensor technologies. As shrinking conventional integrated circuits became more challenging, researchers began exploring electronics with the potential to penetrate new applications with a low price of entry: "Electronics everywhere." The new generation of electronics is thin, light, flexible, and inexpensive. Organic electronics are part of the new generation of thin-film electronics, relying on the synthetic flexibility of carbon molecules to create organic semiconductors, absorbers, and emitters which perform useful tasks. Organic electronics can be fabricated with low energy input on a variety of novel substrates, including inexpensive plastic sheets. The potential ease of synthesis and fabrication of organic-based devices means that organic electronics can be made at very low cost. Successfully demonstrated organic semiconductor devices include photovoltaics, photodetectors, transistors, and light emitting diodes. Several challenges that face organic semiconductor devices are low performance relative to conventional devices, long-term device stability, and development of new organic-compatible processes and materials. While the absorption and emission performance of organic materials in photovoltaics and light emitting diodes is extraordinarily high for thin films, the charge conduction mobilities are generally low. Building highly efficient devices with low-mobility materials is one challenge. Many organic semiconductor films are unstable during fabrication, storage, and operation due to reactions with water, oxygen and hydroxide. A final challenge facing organic electronics is the need for new processes and materials for electrodes

  2. Nanotube devices based crossbar architecture: toward neuromorphic computing

    International Nuclear Information System (INIS)

    Zhao, W S; Gamrat, C; Agnus, G; Derycke, V; Filoramo, A; Bourgoin, J-P

    2010-01-01

    Nanoscale devices such as carbon nanotube and nanowires based transistors, memristors and molecular devices are expected to play an important role in the development of new computing architectures. While their size represents a decisive advantage in terms of integration density, it also raises the critical question of how to efficiently address large numbers of densely integrated nanodevices without the need for complex multi-layer interconnection topologies similar to those used in CMOS technology. Two-terminal programmable devices in crossbar geometry seem particularly attractive, but suffer from severe addressing difficulties due to cross-talk, which implies complex programming procedures. Three-terminal devices can be easily addressed individually, but with limited gain in terms of interconnect integration. We show how optically gated carbon nanotube devices enable efficient individual addressing when arranged in a crossbar geometry with shared gate electrodes. This topology is particularly well suited for parallel programming or learning in the context of neuromorphic computing architectures.

  3. I. Hole-transporting dendrimers and their use in organic light-emitting devices (OLEDs) and II. Novel layered catalysts containing bipyridinium and zero-valent metal species

    Science.gov (United States)

    Koene, Shannon Carol

    A series of polyaromatic ether/ester dendrimers containing a hole transporting naphthylphenylbenzyl amine at the periphery and a variety of fluorescent dyes at the core has been studied in an effort to observe energy transfer in these species. The dyes incorporated in these dendrimers include 1,4-dihydroxyanthraquinone (quinizarin), Coumarin 343, and a benzopentathiophene. These dendrimers have been incorporated into both single layer and heterostructure organic light emitting devices (OLEDs). In the case of first generation dendrimer OLEDs, excimer/exciplex formation was predominant. In third generation dendrimers, complete energy transfer from the periphery to the dye at the core was observed both in photoluminescence spectra and electroluminescence in OLEDs. Dendrimers containing different dye cores can be combined to achieve color mixing/tuning. In addition, layered catalysts were prepared via both covalent and electrostatic means to achieve the catalytic production of hydrogen peroxide from hydrogen and oxygen. Covalent catalysts were prepared by first growing layers of zirconium and a bipyridinium containing bisphosphonate onto silica particles. Palladium and/or platinum was ion-exchanged into the structure and reduced to the zero valent metal by hydrogen gas. A second set of catalysts was prepared by electrostatically depositing polycations/polyanions onto carboxylate or amine functionalized polystyrene microspheres. Anionic colloidal particles were adsorbed to the polycationic surface. An octacationic viologen oligomer was used in an attempt to increase the affinity of adsorption of the Pd particles to the surface of the microspheres. Catalytic studies of both types of catalysts are herein reported.

  4. Electromagnetic Vibration Energy Harvesting Devices Architectures, Design, Modeling and Optimization

    CERN Document Server

    Spreemann, Dirk

    2012-01-01

    Electromagnetic vibration transducers are seen as an effective way of harvesting ambient energy for the supply of sensor monitoring systems. Different electromagnetic coupling architectures have been employed but no comprehensive comparison with respect to their output performance has been carried out up to now. Electromagnetic Vibration Energy Harvesting Devices introduces an optimization approach which is applied to determine optimal dimensions of the components (magnet, coil and back iron). Eight different commonly applied coupling architectures are investigated. The results show that correct dimensions are of great significance for maximizing the efficiency of the energy conversion. A comparison yields the architectures with the best output performance capability which should be preferably employed in applications. A prototype development is used to demonstrate how the optimization calculations can be integrated into the design–flow. Electromagnetic Vibration Energy Harvesting Devices targets the design...

  5. Disruptive Logic Architectures and Technologies From Device to System Level

    CERN Document Server

    Gaillardon, Pierre-Emmanuel; Clermidy, Fabien

    2012-01-01

    This book discusses the opportunities offered by disruptive technologies to overcome the economical and physical limits currently faced by the electronics industry. It provides a new methodology for the fast evaluation of an emerging technology from an architectural perspective and discusses the implications from simple circuits to complex architectures. Several technologies are discussed, ranging from 3-D integration of devices (Phase Change Memories, Monolithic 3-D, Vertical NanoWires-based transistors) to dense 2-D arrangements (Double-Gate Carbon Nanotubes, Sublithographic Nanowires, Lithographic Crossbar arrangements). Novel architectural organizations, as well as the associated tools, are presented in order to explore this freshly opened design space. Describes a novel architectural organization for future reconfigurable systems; Includes a complete benchmarking toolflow for emerging technologies; Generalizes the description of reconfigurable circuits in terms of hierarchical levels; Assesses disruptive...

  6. Polymer OLED White Light Development Program

    Energy Technology Data Exchange (ETDEWEB)

    Homer Antoniadis; Vi-En Choong; Stelios Choulis; Brian Cumpston; Rahul Gupta; Mathew Mathai; Michael Moyer; Franky So

    2005-12-19

    OSRAM Opto Semiconductors (OSRAM) successfully completed development, fabrication and characterization of the large area, polymer based white light OLED prototype at their OLED Research and Development (R&D) facility in San Jose, CA. The program, funded by the Department of Energy (DOE), consisted of three key objectives: (1) Develop new polymer materials and device architectures--in order to improve the performance of organic light emitters. (2) Develop processing techniques--in order to demonstrate and enable the manufacturing of large area, white light and color tunable, solid state light sources. (3) Develop new electronics and driving schemes for organic light sources, including color-tunable light sources. The key performance goals are listed. A world record efficiency of 25 lm/W was established for the solution processed white organic device from the significant improvements made during the project. However, the challenges to transfer this technology from an R&D level to a large tile format such as, the robustness of the device and the coating uniformity of large area panels, remain. In this regard, the purity and the blend nature of the materials are two factors that need to be addressed in future work. During the first year, OSRAM's Materials and Device group (M&D) worked closely with the major polymer material suppliers to develop the polymer emissive technology. M&D was successful in demonstrating a 7-8 lm/W white light source which was based on fluorescent materials. However, it became apparent that the major gains in efficiency could only be made if phosphorescent materials were utilized. Thus, in order to improve the performance of the resulting devices, the focus of the project shifted towards development of solution-processable phosphorescent light emitting diodes (PHOLEDs) and device architectures. The result is a higher efficiency than the outlined project milestone.

  7. Full-color OLED on silicon microdisplay

    Science.gov (United States)

    Ghosh, Amalkumar P.

    2002-02-01

    eMagin has developed numerous enhancements to organic light emitting diode (OLED) technology, including a unique, up- emitting structure for OLED-on-silicon microdisplay devices. Recently, eMagin has fabricated full color SVGA+ resolution OLED microdisplays on silicon, with over 1.5 million color elements. The display is based on white light emission from OLED followed by LCD-type red, green and blue color filters. The color filters are patterned directly on OLED devices following suitable thin film encapsulation and the drive circuits are built directly on single crystal silicon. The resultant color OLED technology, with hits high efficiency, high brightness, and low power consumption, is ideally suited for near to the eye applications such as wearable PCS, wireless Internet applications and mobile phone, portable DVD viewers, digital cameras and other emerging applications.

  8. Models and prototypes of biomimetic devices to architectural purposes

    Directory of Open Access Journals (Sweden)

    Silvia Titotto

    2014-12-01

    Full Text Available This paper presents some results of an ongoing interdisciplinary research about models and prototypes of biomimetic devices via installations and the focus of this paper is to outline this research role in architectural purposes as it perpasses the cultural and heritage contexts by being a way of understanding and living in the world as well as taking place in the world as devices or environments that pass on to future generations to use, learn from and be inspired by. Both the theoretical and the experimental work done so far point out that installations built with association of laser cutting and rapid prototyping techniques might be on the best feasible ways for developing and testing new technologies involved in biomimetic devices to architectural purposes that put both tectonics and nature as their central theme. 

  9. An Approach for Measuring the Dielectric Strength of OLED Materials

    Directory of Open Access Journals (Sweden)

    Sujith Sudheendran Swayamprabha

    2018-06-01

    Full Text Available Surface roughness of electrodes plays a key role in the dielectric breakdown of thin-film organic devices. The rate of breakdown will increase when there are stochastic sharp spikes on the surface of electrodes. Additionally, surface having spiking morphology makes the determination of dielectric strength very challenging, specifically when the layer is relatively thin. We demonstrate here a new approach to investigate the dielectric strength of organic thin films for organic light-emitting diodes (OLEDs. The thin films were deposited on a substrate using physical vapor deposition (PVD under high vacuum. The device architectures used were glass substrate/indium tin oxide (ITO/organic material/aluminum (Al and glass substrate/Al/organic material/Al. The dielectric strength of the OLED materials was evaluated from the measured breakdown voltage and layer thickness.

  10. Architecture, development and implementation of a SWIR to visible integrated up-conversion imaging device

    Science.gov (United States)

    Sarusi, Gabby; Templeman, Tzvi; Hechster, Elad; Nissim, Nimrod; Vitenberg, Vladimir; Maman, Nitzan; Tal, Amir; Solodar, Assi; Makov, Guy; Abdulhalim, Ibrahim; Visoly-Fisher, Iris; Golan, Yuval

    2016-04-01

    A new concept of short wavelength infrared (SWIR) to visible upconversion integrated imaging device is proposed, modeled and some initial measured results are presented. The device is a hybrid inorganic-organic device that comprises six nano-metric scale sub-layers grown on n-type GaAs substrates. The first layer is a ~300nm thick PbSe nano-columnar absorber layer grown in (111) orientation to the substrate plan (100), with a diameter of 8- 10nm and therefore exhibit quantum confinement effects parallel to the substrate and bulk properties perpendicular to it. The advantage of this structure is the high oscillator strength and hence absorption to incoming SWIR photons while maintaining the high bulk mobility of photo-excited charges along the columns. The top of the PbSe absorber layer is coated with 20nm thick metal layer that serves as a dual sided mirror, as well as a potentially surface plasmon enhanced absorption in the PbSe nano-columns layer. The photo-excited charges (holes and electrons in opposite directions) are drifted under an external applied field to the OLED section (that is composed of a hole transport layer, an emission layer and an electron transport layer) where they recombine with injected electron from the transparent cathode and emit visible light through this cathode. Due to the high absorption and enhanced transport properties this architecture has the potential of high quantum efficiency, low cost and easy implementation in any optical system. As a bench-mark, alternative concept where InGaAs/InP heterojunction couple to liquid crystal optical spatial light modulator (OSLM) structure was built that shows a full upconversion to visible of 1550nm laser light.

  11. OLED microdisplay design and materials

    Science.gov (United States)

    Wacyk, Ihor; Prache, Olivier; Ali, Tariq; Khayrullin, Ilyas; Ghosh, Amalkumar

    2010-04-01

    AMOLED microdisplays from eMagin Corporation are finding growing acceptance within the military display market as a result of their excellent power efficiency, wide operating temperature range, small size and weight, good system flexibility, and ease of use. The latest designs have also demonstrated improved optical performance including better uniformity, contrast, MTF, and color gamut. eMagin's largest format display is currently the SXGA design, which includes features such as a 30-bit wide RGB digital interface, automatic luminance regulation from -45 to +70°C, variable gamma control, and a dynamic range exceeding 50:000 to 1. This paper will highlight the benefits of eMagin's latest microdisplay designs and review the roadmap for next generation devices. The ongoing development of reduced size pixels and larger format displays (up to WUXGA) as well as new OLED device architecture (e.g. high-brightness yellow) will be discussed. Approaches being explored for improved performance in next generation designs such as lowpower serial interfaces, high frame rate operation, and new operational modes for reduction of motion artifacts will also be described. These developments should continue to enhance the appeal of AMOLED microdisplays for a broad spectrum of near-to-the-eye applications such as night vision, simulation and training, situational awareness, augmented reality, medical imaging, and mobile video entertainment and gaming.

  12. Interband cascade (IC) photovoltaic (PV) architecture for PV devices

    Science.gov (United States)

    Yang, Rui Q.; Tian, Zhaobing; Mishima, Tetsuya D.; Santos, Michael B.; Johnson, Matthew B.; Klem, John F.

    2015-10-20

    A photovoltaic (PV) device, comprising a PV interband cascade (IC) stage, wherein the IC PV stage comprises an absorption region with a band gap, the absorption region configured to absorb photons, an intraband transport region configured to act as a hole barrier, and an interband tunneling region configured to act as an electron barrier. An IC PV architecture for a photovoltaic device, the IC PV architecture comprising an absorption region, an intraband transport region coupled to the absorption region, and an interband tunneling region coupled to the intraband transport region and to the adjacent absorption region, wherein the absorption region, the intraband transport region, and the interband tunneling region are positioned such that electrons will flow from the absorption region to the intraband transport region to the interband tunneling region.

  13. Different Device Architectures for Bulk-Heterojunction Solar Cells

    Directory of Open Access Journals (Sweden)

    Getachew Adam

    2016-08-01

    Full Text Available We report different solar cell designs which allow a simple electrical connection of subsequent devices deposited on the same substrate. By arranging so-called standard and inverted solar-cell architectures next to each other, a serial connection of the two devices can easily be realized by a single compound electrode. In this work, we tested different interfacial layer materials like polyethylenimine (PEI and PEDOT:PSS, and silver as a non-transparent electrode material. We also built organic light emitting diodes applying the same device designs demonstrating the versatility of applied layer stacks. The proposed design should allow the preparation of organic bulk-heterojunction modules with minimized photovoltaically inactive regions at the interconnection of individual devices.

  14. Improving Software Performance in the Compute Unified Device Architecture

    Directory of Open Access Journals (Sweden)

    Alexandru PIRJAN

    2010-01-01

    Full Text Available This paper analyzes several aspects regarding the improvement of software performance for applications written in the Compute Unified Device Architecture CUDA. We address an issue of great importance when programming a CUDA application: the Graphics Processing Unit’s (GPU’s memory management through ranspose ernels. We also benchmark and evaluate the performance for progressively optimizing a transposing matrix application in CUDA. One particular interest was to research how well the optimization techniques, applied to software application written in CUDA, scale to the latest generation of general-purpose graphic processors units (GPGPU, like the Fermi architecture implemented in the GTX480 and the previous architecture implemented in GTX280. Lately, there has been a lot of interest in the literature for this type of optimization analysis, but none of the works so far (to our best knowledge tried to validate if the optimizations can apply to a GPU from the latest Fermi architecture and how well does the Fermi architecture scale to these software performance improving techniques.

  15. SOA-BD: Service Oriented Architecture for Biomedical Devices

    Directory of Open Access Journals (Sweden)

    João Marcos Teixeira Lacerda

    2017-05-01

    Full Text Available Introduction: The communication of information systems with biomedical devices has become complex not only due to the existence of several private communication protocols, but also to the immutable way that software is embedded into these devices. In this sense, this paper proposes a service-oriented architecture to access biomedical devices as a way to abstract the mechanisms of writing and reading data from these devices, thus contributing to enable the focus of the development team of biomedical software to be intended for its functional requirements, i.e. business rules relevant to the problem domain. Methods The SOA-BD architecture consists of five main components: A Web Service for transport and conversion of the device data, Communication Protocols to access the devices, Data Parsers to preprocess data, a Device Repository to store data and transmitted information and Error handling, for error handling of these information. For the development of SOA-BD, technologies such as the XML language and the Java programming language were used. Besides, Software Engineering concepts such as Design Patterns were also used. For the validation of this work, data has been collected from vital sign monitors in an Intensive Care Unit using HL7 standards. Results The tests obtained a difference of about only 1 second in terms of response time with the use of SOA-BD. Conclusion SOA-BD achieves important results such as the reduction on the access protocol complexity, the opportunity for treating patients over long distances, allowing easier development of monitoring applications and interoperability with biomedical devices from diverse manufacturers.

  16. Digital Device Architecture and the Safe Use of Flash Devices in Munitions

    Science.gov (United States)

    Katz, Richard B.; Flowers, David; Bergevin, Keith

    2017-01-01

    Flash technology is being utilized in fuzed munition applications and, based on the development of digital logic devices in the commercial world, usage of flash technology will increase. Digital devices of interest to designers include flash-based microcontrollers and field programmable gate arrays (FPGAs). Almost a decade ago, a study was undertaken to determine if flash-based microcontrollers could be safely used in fuzes and, if so, how should such devices be applied. The results were documented in the Technical Manual for the Use of Logic Devices in Safety Features. This paper will first review the Technical Manual and discuss the rationale behind the suggested architectures for microcontrollers and a brief review of the concern about data retention in flash cells. An architectural feature in the microcontroller under study will be discussed and its use will show how to screen for weak or failed cells during manufacture, storage, or immediately prior to use. As was done for microcontrollers a decade ago, architectures for a flash-based FPGA will be discussed, showing how it can be safely used in fuzes. Additionally, architectures for using non-volatile (including flash-based) storage will be discussed for SRAM-based FPGAs.

  17. Control system devices : architectures and supply channels overview.

    Energy Technology Data Exchange (ETDEWEB)

    Trent, Jason; Atkins, William Dee; Schwartz, Moses Daniel; Mulder, John C.

    2010-08-01

    This report describes a research project to examine the hardware used in automated control systems like those that control the electric grid. This report provides an overview of the vendors, architectures, and supply channels for a number of control system devices. The research itself represents an attempt to probe more deeply into the area of programmable logic controllers (PLCs) - the specialized digital computers that control individual processes within supervisory control and data acquisition (SCADA) systems. The report (1) provides an overview of control system networks and PLC architecture, (2) furnishes profiles for the top eight vendors in the PLC industry, (3) discusses the communications protocols used in different industries, and (4) analyzes the hardware used in several PLC devices. As part of the project, several PLCs were disassembled to identify constituent components. That information will direct the next step of the research, which will greatly increase our understanding of PLC security in both the hardware and software areas. Such an understanding is vital for discerning the potential national security impact of security flaws in these devices, as well as for developing proactive countermeasures.

  18. Improved electron injection in spin coated Alq3 incorporated ZnO thin film in the device for solution processed OLEDs

    Science.gov (United States)

    Dasi, Gnyaneshwar; Ramarajan, R.; Thangaraju, Kuppusamy

    2018-04-01

    We deposit tris-(8-hydroxyquinoline)aluminum (Alq3) incorporated zinc oxide (ZnO) thin films by spin coating method under the normal ambient. It showed the higher transmittance (90% at 550 nm) when compared to that (80% at 550 nm) of spin coated pure ZnO film. SEM studies show that the Alq3 incorporation in ZnO film also enhances the formation of small sized particles arranged in the network of wrinkles on the surface. XRD reveals the improved crystalline properties upon Alq3 inclusion. We fabricate the electron-only devices (EODs) with the structure of ITO/spin coated ZnO:Alq3 as ETL/Alq3 interlayer/LiF/Al. The device showed the higher electron current density of 2.75 mA/cm2 at 12V when compared to that (0.82 mA/cm2 at 12V) of the device using pure ZnO ETL. The device results show that it will be useful to fabricate the low-cost solution processed OLEDs for future lighting and display applications.

  19. Effect of hole injection layer/hole transport layer polymer and device structure on the properties of white OLED.

    Science.gov (United States)

    Cho, Ho Young; Park, Eun Jung; Kim, Jin-Hoo; Park, Lee Soon

    2008-10-01

    Copolymers containing carbazole and aromatic amine unit were synthesized by using Pd-catalyzed polycondensation reaction. The polymers were characterized in terms of their molecular weight and thermal stability and their UV and PL properties in solution and film state. The band gap energy of the polymers was also determined by the UV absorption and HOMO energy level data. The polymers had high HOMO energy level of 5.19-5.25 eV and work function close to that of ITO. The polymers were thus tested as hole injection/transport layer in the white organic light emitting diodes (OLED) by using 4,4'-bis(2,2-diphenyl-ethen-1-yl)diphenyl (DPVBi) as blue emitting material and 5,6,11,12-tetraphenylnaphthacene (Rubrene) as orange emitting dopant. The synthesized polymer, poly bis[6-bromo-N-(2-ethylhexyl)-carbazole-3-yl] was found to be useful as hole injection layer/hole transport layer (HIL/HTL) multifunctional material with high luminance efficiency and stable white color coordinate in the wide range of applied voltage.

  20. Mesoporous nanocrystalline film architecture for capacitive storage devices

    Science.gov (United States)

    Dunn, Bruce S.; Tolbert, Sarah H.; Wang, John; Brezesinski, Torsten; Gruner, George

    2017-05-16

    A mesoporous, nanocrystalline, metal oxide construct particularly suited for capacitive energy storage that has an architecture with short diffusion path lengths and large surface areas and a method for production are provided. Energy density is substantially increased without compromising the capacitive charge storage kinetics and electrode demonstrates long term cycling stability. Charge storage devices with electrodes using the construct can use three different charge storage mechanisms immersed in an electrolyte: (1) cations can be stored in a thin double layer at the electrode/electrolyte interface (non-faradaic mechanism); (2) cations can interact with the bulk of an electroactive material which then undergoes a redox reaction or phase change, as in conventional batteries (faradaic mechanism); or (3) cations can electrochemically adsorb onto the surface of a material through charge transfer processes (faradaic mechanism).

  1. OLEDs : Technology's next generation

    Energy Technology Data Exchange (ETDEWEB)

    Anon

    2001-10-01

    Major advances in organic light emitting device (OLED) technology are bringing some science fiction concepts to the brink of reality. At the moment. OLED technology is being developed for the flat panel display industry. Liquid crystal display dominates the market for wristwatches and cellular phones for example, while the cathode ray tube plays the same role for television sets and desktop computers. Both have limitations when it comes to meeting the needs of the next generation of smart products. The attributes required include high brightness, low power consumption, high definition, full colour, wide preview angle, fast response time and portability, and low cost. OLED has the potential to meet all those requirements. Universal Display Corporation (UDC) was founded, and specializes in the development and commercialization of OLED technology. A partnership was established early with Princeton University professors, and no fewer than 20 researchers are working on OLED technology projects at both Princeton University and the University of Southern California. To date, 35 patents have been issued, and 60 others are pending. A joint development agreement was reached with Sony Corporation this year for high efficiency active matrix OLEDs to be used in large area monitor applications. OLED technology is based on vacuum-deposited organic small molecule materials that emit very bright light when electrically stimulated. Three advances in the technology were briefly discussed: TOLED{sup TM} for Transparent OLED, SOLED{sup TM} for Stacked OLED, and FOLED{sup TM} for Flexible OLED. A list detailing the various potential uses for the technology was also included in this paper. 3 figs.

  2. Integrated Plastic Substrates for OLED Lighting

    Energy Technology Data Exchange (ETDEWEB)

    Gaynor, Whitney

    2015-08-01

    OLED lighting has immense potential as aesthetically pleasing, energy-efficient general illumination. Unlike other light sources, such as incandescents, fluorescents, and inorganic LEDs, OLEDs naturally emit over a large-area surface. They are glare free, do not need to be shaded, and are cool to the touch, requiring no heatsink. The best efficiencies and lifetimes reported are on par with or better than current forms of illumination. However, the cost for OLED lighting remains high – so much so that these products are not market competitive and there is very low consumer demand. We believe that flexible, plastic-based devices will highlight the advantages of aesthetically-pleasing OLED lighting systems while paving the way for lowering both materials and manufacturing costs. These flexible devices require new development in substrate and support technology, which was the focus of the work reported here. The project team, led by Sinovia Technologies, has developed integrated plastic substrates to serve as supports for flexible OLED lighting. The substrates created in this project would enable large-area, flexible devices and are specified to perform three functions. They include a barrier to protect the OLED from moisture and oxygen-related degradation, a smooth, highly conductive transparent electrode to enable large-area device operation, and a light scattering layer to improve emission efficiency. Through the course of this project, integrated substrates were fabricated, characterized, evaluated for manufacturing feasibility and cost, and used in white OLED demonstrations to test their impact on flexible OLED lighting. Our integrated substrates meet or exceed the DOE specifications for barrier performance in water vapor and oxygen transport rates, as well as the transparency and conductivity of the anode film. We find that these integrated substrates can be manufactured in a completely roll-to-roll, high throughput process and have developed and demonstrated

  3. Top emitting white OLEDs

    Energy Technology Data Exchange (ETDEWEB)

    Freitag, Patricia; Luessem, Bjoern; Leo, Karl [Technische Universitaet Dresden, Institut fuer Angewandte Photophysik, George-Baehr-Strasse 1, 01069 Dresden (Germany)

    2009-07-01

    Top emitting organic light emitting diodes (TOLEDs) provide a number of interesting opportunities for new applications, such as the opportunity to fabricate ITO-free devices by using opaque substrates. This makes it possible to manufacture low cost OLEDs for signage and lighting applications. A general top emitting device consists of highly reflecting metal contacts as anode and semitransparent cathode, the latter one for better outcouling reasons. In between several organic materials are deposited as charge transporting, blocking, and emission layers. Here, we show a top emitting white organic light emitting diode with silver electrodes arranged in a p-i-n structure with p- and n-doped charge transport layers. The centrical emission layer consists of two phosphorescent (red and green) and one fluorescent (blue) emitter systems separated by an ambipolar interlayer to avoid mutual exciton quenching. By adding an additional dielectric capping layer on top of the device stack, we achieve a reduction of the strong microcavity effects which appear due to the high reflection of both metal electrodes. Therefore, the outcoupled light shows broad and nearly angle-independent emission spectra, which is essential for white light emitting diodes.

  4. New device architecture of a thermoelectric energy conversion for recovering low-quality heat

    Science.gov (United States)

    Kim, Hoon; Park, Sung-Geun; Jung, Buyoung; Hwang, Junphil; Kim, Woochul

    2014-03-01

    Low-quality heat is generally discarded for economic reasons; a low-cost energy conversion device considering price per watt, /W, is required to recover this waste heat. Thin-film based thermoelectric devices could be a superior alternative for this purpose, based on their low material consumption; however, power generated in conventional thermoelectric device architecture is negligible due to the small temperature drop across the thin film. To overcome this challenge, we propose new device architecture, and demonstrate approximately 60 Kelvin temperature differences using a thick polymer nanocomposite. The temperature differences were achieved by separating the thermal path from the electrical path; whereas in conventional device architecture, both electrical charges and thermal energy share same path. We also applied this device to harvest body heat and confirmed its usability as an energy conversion device for recovering low-quality heat.

  5. High Brightness OLED Lighting

    Energy Technology Data Exchange (ETDEWEB)

    Spindler, Jeffrey [OLEDWorks LLC; Kondakova, Marina [OLEDWorks LLC; Boroson, Michael [OLEDWorks LLC; Hamer, John [OLEDWorks LLC

    2016-05-25

    In this work we describe the technology developments behind our current and future generations of high brightness OLED lighting panels. We have developed white and amber OLEDs with excellent performance based on the stacking approach. Current products achieve 40-60 lm/W, while future developments focus on achieving 80 lm/W or higher.

  6. A CMOS self-powered front-end architecture for subcutaneous event-detector devices

    CERN Document Server

    Colomer-Farrarons, Jordi

    2011-01-01

    A CMOS Self-Powered Front-End Architecture for Subcutaneous Event-Detector Devices presents the conception and prototype realization of a Self-Powered architecture for subcutaneous detector devices. The architecture is designed to work as a true/false (event detector) or threshold level alarm of some substances, ions, etc. that are detected through a three-electrodes amperometric BioSensor approach. The device is conceived as a Low-Power subcutaneous implantable application powered by an inductive link, one emitter antenna at the external side of the skin and the receiver antenna under the ski

  7. Photovoltaic effect on the performance enhancement of organic light-emitting diodes with planar heterojunction architecture

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Dan; Huang, Wei; Guo, Hao [State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China); Wang, Hua, E-mail: wanghua001@tyut.edu.cn [Research Center of Advanced Materials Science and Technology, Taiyuan University of Technology (TYUT), Taiyuan 030024 (China); Yu, Junsheng, E-mail: jsyu@uestc.edu.cn [State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)

    2017-04-15

    Highlights: • The photovoltaic effect on the performance of OLEDs was studied. • The device performance with different planar heterojunctions was investigated. • The mechanism relies on the overlap of electroluminescence and absorption spectrum. - Abstract: Organic light-emitting diodes (OLEDs) with planar heterojunction (PHJ) architecture consisting of photovoltaic organic materials of fullerene carbon 60 (C{sub 60}) and copper (II) phthalocyanine (CuPc) inserted between emitting unit and cathode were constructed, and the photovoltaic effect on OLEDs performance was studied. The electroluminescent (EL) characteristics and mechanism of device performance variation without and with different PHJs (herein including C{sub 60}/CuPc, CuPc/C{sub 60} and CuPc) were systematically investigated in red, green and blue OLEDs. Of the three combinations, OLEDs with C{sub 60}/CuPc showed the highest efficiency. It is revealed that the photovoltaic C{sub 60}/CuPc PHJ can absorb part of photons, which are radiated from emission zone, then form excitons, and dissociated into free charges. Consequently, the high device efficiency of OLEDs performance improvement was acquired. This research demonstrates that PHJ consisting of two n- and p-type photovoltaic organic materials could be a promising methodology for high performance OLEDs.

  8. Photovoltaic effect on the performance enhancement of organic light-emitting diodes with planar heterojunction architecture

    International Nuclear Information System (INIS)

    Zhao, Dan; Huang, Wei; Guo, Hao; Wang, Hua; Yu, Junsheng

    2017-01-01

    Highlights: • The photovoltaic effect on the performance of OLEDs was studied. • The device performance with different planar heterojunctions was investigated. • The mechanism relies on the overlap of electroluminescence and absorption spectrum. - Abstract: Organic light-emitting diodes (OLEDs) with planar heterojunction (PHJ) architecture consisting of photovoltaic organic materials of fullerene carbon 60 (C_6_0) and copper (II) phthalocyanine (CuPc) inserted between emitting unit and cathode were constructed, and the photovoltaic effect on OLEDs performance was studied. The electroluminescent (EL) characteristics and mechanism of device performance variation without and with different PHJs (herein including C_6_0/CuPc, CuPc/C_6_0 and CuPc) were systematically investigated in red, green and blue OLEDs. Of the three combinations, OLEDs with C_6_0/CuPc showed the highest efficiency. It is revealed that the photovoltaic C_6_0/CuPc PHJ can absorb part of photons, which are radiated from emission zone, then form excitons, and dissociated into free charges. Consequently, the high device efficiency of OLEDs performance improvement was acquired. This research demonstrates that PHJ consisting of two n- and p-type photovoltaic organic materials could be a promising methodology for high performance OLEDs.

  9. Model & scale as conceptual devices in architectural representation

    NARCIS (Netherlands)

    Stellingwerff, M.C.; Koorstra, P.A.

    2013-01-01

    This year we celebrate the tenth anniversary of our Computer Aided Manufacturing laboratory (CAMlab, http://www.camlab-bk.nl). From the start we provide laser cutting, CNC-milling and 3D-print facilities for the students and the researchers at the Faculty of Architecture in Delft. Over the past ten

  10. Multidimensional materials and device architectures for future hybrid energy storage

    Science.gov (United States)

    Lukatskaya, Maria R.; Dunn, Bruce; Gogotsi, Yury

    2016-09-01

    Electrical energy storage plays a vital role in daily life due to our dependence on numerous portable electronic devices. Moreover, with the continued miniaturization of electronics, integration of wireless devices into our homes and clothes and the widely anticipated `Internet of Things', there are intensive efforts to develop miniature yet powerful electrical energy storage devices. This review addresses the cutting edge of electrical energy storage technology, outlining approaches to overcome current limitations and providing future research directions towards the next generation of electrical energy storage devices whose characteristics represent a true hybridization of batteries and electrochemical capacitors.

  11. OLEDs for lighting applications

    Science.gov (United States)

    van Elsbergen, V.; Boerner, H.; Löbl, H.-P.; Goldmann, C.; Grabowski, S. P.; Young, E.; Gaertner, G.; Greiner, H.

    2008-08-01

    Organic light emitting diodes (OLEDs) provide potential for power-efficient large area light sources that combine revolutionary properties. They are thin and flat and in addition they can be transparent, colour-tuneable, or flexible. We review the state of the art in white OLEDs and present performance data for three-colour hybrid white OLEDs on indexmatched substrates. With improved optical outcoupling 45 lm/W are achieved. Using a half-sphere to collect all the light that is in the substrate results in 80 lm/W. Optical modelling supports the experimental work. For decorative applications features like transparency and colour tuning are very appealing. We show results on transparent white OLEDs and two ways to come to a colour-variable OLED. These are lateral separation of different colours in a striped design and direct vertical stacking of the different emitting layers. For a striped colour tuneable OLED 36 lm/W are achieved in white with improved optical outcoupling.

  12. Influência de diferentes solventes utilizados na deposição de filme de poli(9-vinilcarbazol em dispositivos OLEDs

    Directory of Open Access Journals (Sweden)

    Emerson Roberto Santos

    2014-01-01

    Full Text Available This work studies the influence of the film deposition process on light emission performance and on threshold voltage of OLEDs, with architecture glass/ITO/PEDOT:PSS/PVK/Alq3/Al. The commercial PVK was dissolved in different solvents such as: chloroform, tetrahydrofuran, 1,2,4-trichlorobenzene and trimethylpentane. OLEDs were characterized by current-voltage and revealed a significant influence of the solvents, although all devices emitted green electroluminescence. A difference in threshold voltage up to 10 V was observed among OLEDs prepared from different solvents. The 1,2,4-trichlorobenzene showed best performance, presenting lowest treshold voltage (≈ 6 V, followed by tetrahydrofuran (≈ 8 V, trimethylpentane (≈ 14 V and chloroform (≈ 16 V.

  13. Usable Authentication with an Offline Trusted Device Proxy Architecture (long version)

    OpenAIRE

    Johansen, Christian; Jøsang, Audun; Migdal, Denis

    2016-01-01

    Client platform infection poses a significant threat to secure user authentication. Com- bining vulnerable client platforms with special security devices, as often the case in e- banking, can increase significantly the security. This paper describes a new architecture where a security proxy on the client platform communicates with both a trusted security device and the server application. The proxy switches between two TLS channels, one from the client and another from the trusted device. The...

  14. Architectural Vulnerabilities of Third-Generation Portable Devices

    National Research Council Canada - National Science Library

    Chin, Shiu-Kai

    2007-01-01

    .... We developed a handheld evidence recovery operator to address the challenges created by user passwords and PINs, and a standalone tool to copy the data located on the device to an external storage...

  15. The pedagogy of building solar devices in architecture schools

    Energy Technology Data Exchange (ETDEWEB)

    Lee, T. G. [Calgary Univ., Faculty of Environmental Design, AB (Canada)

    1999-11-01

    Education and training of students of architecture, industrial design, planning and environmental sciences in solar energy utilization, as practiced at the University of Calgary, is described. Classes are relatively small, which allows for considerable flexibility in terms of the different modes of instruction. Lectures, case studies, field trips and workshops all have their place, although the most effective and most popular mode of instruction is the hands-on approach in building and installing a solar heating system. During the course, the students build various types of solar cookers and concentrating solar collectors, including air-type and water-type flat plate collectors. Usually one solar component is built by each class, but previous projects are available for examination and monitoring. This paper elaborates upon the pedagogical basis of shop experience for architectural students. In this context it addresses issues related to shop space, materials, construction, installation testing and monitoring, as well as safety and performance of the student-constructed solar systems. 3 refs., 9 figs.

  16. The pedagogy of building solar devices in architecture schools

    Energy Technology Data Exchange (ETDEWEB)

    Lee, T. G. (Calgary Univ., Faculty of Environmental Design, AB (Canada))

    1999-01-01

    Education and training of students of architecture, industrial design, planning and environmental sciences in solar energy utilization, as practiced at the University of Calgary, is described. Classes are relatively small, which allows for considerable flexibility in terms of the different modes of instruction. Lectures, case studies, field trips and workshops all have their place, although the most effective and most popular mode of instruction is the hands-on approach in building and installing a solar heating system. During the course, the students build various types of solar cookers and concentrating solar collectors, including air-type and water-type flat plate collectors. Usually one solar component is built by each class, but previous projects are available for examination and monitoring. This paper elaborates upon the pedagogical basis of shop experience for architectural students. In this context it addresses issues related to shop space, materials, construction, installation testing and monitoring, as well as safety and performance of the student-constructed solar systems. 3 refs., 9 figs.

  17. Modifying the organic/electrode interface in Organic Solar Cells (OSCs) and improving the efficiency of solution-processed phosphorescent Organic Light-Emitting Diodes (OLEDs)

    Energy Technology Data Exchange (ETDEWEB)

    Xiao, Teng [Iowa State Univ., Ames, IA (United States)

    2012-01-01

    Organic semiconductors devices, such as, organic solar cells (OSCs), organic light-emitting diodes (OLEDs) and organic field-effect transistors (OFETs) have drawn increasing interest in recent decades. As organic materials are flexible, light weight, and potentially low-cost, organic semiconductor devices are considered to be an alternative to their inorganic counterparts. This dissertation will focus mainly on OSCs and OLEDs. As a clean and renewable energy source, the development of OSCs is very promising. Cells with 9.2% power conversion efficiency (PCE) were reported this year, compared to < 8% two years ago. OSCs belong to the so-called third generation solar cells and are still under development. While OLEDs are a more mature and better studied field, with commercial products already launched in the market, there are still several key issues: (1) the cost of OSCs/OLEDs is still high, largely due to the costly manufacturing processes; (2) the efficiency of OSCs/OLEDs needs to be improved; (3) the lifetime of OSCs/OLEDs is not sufficient compared to their inorganic counterparts; (4) the physics models of the behavior of the devices are not satisfactory. All these limitations invoke the demand for new organic materials, improved device architectures, low-cost fabrication methods, and better understanding of device physics. For OSCs, we attempted to improve the PCE by modifying the interlayer between active layer/metal. We found that ethylene glycol (EG) treated poly(3,4-ethylenedioxythiophene): polystyrenesulfonate (PEDOT: PSS) improves hole collection at the metal/polymer interface, furthermore it also affects the growth of the poly(3- hexylthiophene) (P3HT):phenyl-C61-butyric acid methyl ester (PCBM) blends, making the phase segregation more favorable for charge collection. We then studied organic/inorganic tandem cells. We also investigated the effect of a thin LiF layer on the hole-collection of copper phthalocyanine (CuPc)/C70-based small molecular OSCs. A

  18. A Hybrid Web Browser Architecture for Mobile Devices

    Directory of Open Access Journals (Sweden)

    CHO, J.

    2014-08-01

    Full Text Available Web browsing on mobile networks is slow in comparison to wired or Wi-Fi networks. Particularly, the connection establishment phase including DNS lookups and TCP handshakes takes a long time on mobile networks due to its long round-trip latency. In this paper, we propose a novel web browser architecture that aims to improve mobile web browsing performance. Our approach delegates the connection establishment and HTTP header field delivery tasks to a dedicated proxy server located at the joint point between the WAN and mobile network. Since the traffic for the connection establishment and HTTP header fields delivery passes only through the WAN between the proxy and web servers, our approach significantly reduces both the number and size of packets on the mobile network. Our evaluation showed that the proposed scheme reduces the number of mobile network packets by up to 42% and, consequently, the average page loading time is shortened by up to 52%.

  19. Towards efficient next generation light sources: combined solution processed and evaporated layers for OLEDs

    Science.gov (United States)

    Hartmann, D.; Sarfert, W.; Meier, S.; Bolink, H.; García Santamaría, S.; Wecker, J.

    2010-05-01

    Typically high efficient OLED device structures are based on a multitude of stacked thin organic layers prepared by thermal evaporation. For lighting applications these efficient device stacks have to be up-scaled to large areas which is clearly challenging in terms of high through-put processing at low-cost. One promising approach to meet cost-efficiency, high through-put and high light output is the combination of solution and evaporation processing. Moreover, the objective is to substitute as many thermally evaporated layers as possible by solution processing without sacrificing the device performance. Hence, starting from the anode side, evaporated layers of an efficient white light emitting OLED stack are stepwise replaced by solution processable polymer and small molecule layers. In doing so different solutionprocessable hole injection layers (= polymer HILs) are integrated into small molecule devices and evaluated with regard to their electro-optical performance as well as to their planarizing properties, meaning the ability to cover ITO spikes, defects and dust particles. Thereby two approaches are followed whereas in case of the "single HIL" approach only one polymer HIL is coated and in case of the "combined HIL" concept the coated polymer HIL is combined with a thin evaporated HIL. These HIL architectures are studied in unipolar as well as bipolar devices. As a result the combined HIL approach facilitates a better control over the hole current, an improved device stability as well as an improved current and power efficiency compared to a single HIL as well as pure small molecule based OLED stacks. Furthermore, emitting layers based on guest/host small molecules are fabricated from solution and integrated into a white hybrid stack (WHS). Up to three evaporated layers were successfully replaced by solution-processing showing comparable white light emission spectra like an evaporated small molecule reference stack and lifetime values of several 100 h.

  20. Sub-Band Gap Turn-On Near-Infrared-to-Visible Up-Conversion Device Enabled by an Organic-Inorganic Hybrid Perovskite Photovoltaic Absorber.

    Science.gov (United States)

    Yu, By Hyeonggeun; Cheng, Yuanhang; Li, Menglin; Tsang, Sai-Wing; So, Franky

    2018-05-09

    Direct integration of an infrared (IR) photodetector with an organic light-emitting diode (OLED) enables low-cost, pixel-free IR imaging. However, the operation voltage of the resulting IR-to-visible up-conversion is large because of the series device architecture. Here, we report a low-voltage near-IR (NIR)-to-visible up-conversion device using formamidinium lead iodide as a NIR absorber integrated with a phosphorescent OLED. Because of the efficient photocarrier injection from the hybrid perovskite layer to the OLED, we observed a sub-band gap turn-on of the OLED under NIR illumination. The device showed a NIR-to-visible up-conversion efficiency of 3% and a luminance on/off ratio of 10 3 at only 5 V. Finally, we demonstrate pixel-free NIR imaging using the up-conversion device.

  1. OLED microdisplays in near-to-eye applications: challenges and solutions

    Science.gov (United States)

    Vogel, Uwe; Richter, Bernd; Wartenberg, Philipp; König, Peter; Hild, Olaf R.; Fehse, Karsten; Schober, Matthias; Bodenstein, Elisabeth; Beyer, Beatrice

    2017-06-01

    Wearable augmented-reality (AR) has already started to be used productively mainly in manufacturing industry and logistics. Next step will be to move wearable AR from "professionals to citizens" by enabling networked, everywhere augmented-reality (in-/outdoor localisation, scene recognition, cloud access,…) which is non-intrusive, exhibits intuitive user-interaction, anytime safe and secure use, and considers personal privacy protection (user's and others). Various hardware improvements (e.g., low-power, seamless interactivity, small form factor, ergonomics,…), as well as connectivity and network integration will become vital for consumer adoption. Smart-Glasses (i.e., near-to-eye (NTE) displays) have evolved as major devices for wearable AR, that hold potential to become adopted by consumers soon. Tiny microdisplays are a key component of smart-glasses, e.g., creating images from organic light emitting diodes (OLED), that have become popular in mobile phone displays. All microdisplay technologies on the market comprise an image-creating pixel modulation, but only the emissive ones (for example, OLED and LED) feature the image and light source in a single device, and therefore do not require an external light source. This minimizes system size and power consumption, while providing exceptional contrast and color space. These advantages make OLED microdisplays a perfect fit for near-eye applications. Low-power active-matrix circuitry CMOS backplane architecture, embedded sensors, emission spectra outside the visible and high-resolution sub-pixel micro-patterning address some of the application challenges (e.g., long battery life, sun-light readability, user interaction modes) and enable advanced features for OLED microdisplays in near-to-eye displays, e.g., upcoming connected augmented-reality smart glasses. This report is to analyze the challenges in addressing those features and discuss solutions.

  2. Large-area OLED lightings and their applications

    International Nuclear Information System (INIS)

    Park, J W; Shin, D C; Park, S H

    2011-01-01

    In this paper, we review the key issues related to the fabrication of large-area organic light-emitting devices (OLEDs) for lighting applications. We discuss the origin of a short-circuit problem, luminance non-uniformity, hot spot, efficiency reduction (power loss), and heat generation and present the way of suppressing them. We also introduce three different application areas of large-area OLED lighting panels. They can be integrated with a solar cell for power recycling or inorganic LEDs for emotional lightings. The feasibility of using OLEDs for the application of visible-light communications is also reviewed

  3. 2D Material Device Architectures: Process Optimisation and Characterisation

    DEFF Research Database (Denmark)

    Gammelgaard, Lene

    to stack two-dimensional crystals with atomically clean interphases, through a procedure termed van der Waals assembly. We have further developed this assembly method with the \\Hot pick-up" method, which enables batch assembly as well as assembly with pre-patterned crystals. Inclusion of pre...... devices. Additionally, the long-term stability of transition metal dichalcogenides has been studied, and the order of the layers has been demonstrated detectable by atomic force microscopy. The encapsulated van der Waals heterostructures give high performance and long-term stability of two......-dimensional layered materials. The integration of pre-patterned layers, postpatterning of van der Waals heterostructures and detection of the layer order enables control { not only of the vertical ordering of atomic layers { but also in the lateral dimension, facilitating fabrication of advanced metamaterials...

  4. Highly efficient fully transparent inverted OLEDs

    Science.gov (United States)

    Meyer, J.; Winkler, T.; Hamwi, S.; Schmale, S.; Kröger, M.; Görrn, P.; Johannes, H.-H.; Riedl, T.; Lang, E.; Becker, D.; Dobbertin, T.; Kowalsky, W.

    2007-09-01

    One of the unique selling propositions of OLEDs is their potential to realize highly transparent devices over the visible spectrum. This is because organic semiconductors provide a large Stokes-Shift and low intrinsic absorption losses. Hence, new areas of applications for displays and ambient lighting become accessible, for instance, the integration of OLEDs into the windshield or the ceiling of automobiles. The main challenge in the realization of fully transparent devices is the deposition of the top electrode. ITO is commonly used as transparent bottom anode in a conventional OLED. To obtain uniform light emission over the entire viewing angle and a low series resistance, a TCO such as ITO is desirable as top contact as well. However, sputter deposition of ITO on top of organic layers causes damage induced by high energetic particles and UV radiation. We have found an efficient process to protect the organic layers against the ITO rf magnetron deposition process of ITO for an inverted OLED (IOLED). The inverted structure allows the integration of OLEDs in more powerful n-channel transistors used in active matrix backplanes. Employing the green electrophosphorescent material Ir(ppy) 3 lead to IOLED with a current efficiency of 50 cd/A and power efficiency of 24 lm/W at 100 cd/m2. The average transmittance exceeds 80 % in the visible region. The on-set voltage for light emission is lower than 3 V. In addition, by vertical stacking we achieved a very high current efficiency of more than 70 cd/A for transparent IOLED.

  5. An architecture for integrating planar and 3D cQED devices

    Energy Technology Data Exchange (ETDEWEB)

    Axline, C.; Reagor, M.; Heeres, R.; Reinhold, P.; Wang, C.; Shain, K.; Pfaff, W.; Chu, Y.; Frunzio, L.; Schoelkopf, R. J. [Department of Applied Physics, Yale University, New Haven, Connecticut 06511 (United States)

    2016-07-25

    Numerous loss mechanisms can limit coherence and scalability of planar and 3D-based circuit quantum electrodynamics (cQED) devices, particularly due to their packaging. The low loss and natural isolation of 3D enclosures make them good candidates for coherent scaling. We introduce a coaxial transmission line device architecture with coherence similar to traditional 3D cQED systems. Measurements demonstrate well-controlled external and on-chip couplings, a spectrum absent of cross-talk or spurious modes, and excellent resonator and qubit lifetimes. We integrate a resonator-qubit system in this architecture with a seamless 3D cavity, and separately pattern a qubit, readout resonator, Purcell filter, and high-Q stripline resonator on a single chip. Device coherence and its ease of integration make this a promising tool for complex experiments.

  6. Stacked white OLED having separate red, green and blue sub-elements

    Energy Technology Data Exchange (ETDEWEB)

    Forrest, Stephen; Qi, Xiangfei; Slootsky, Michael

    2015-06-23

    The present invention relates to efficient organic light emitting devices (OLEDs). More specifically, the present invention relates to white-emitting OLEDs, or WOLEDs. The devices of the present invention employ three emissive sub-elements, typically emitting red, green and blue, to sufficiently cover the visible spectrum. The sub-elements are separated by charge generating layers.

  7. Stacked white OLED having separate red, green and blue sub-elements

    Science.gov (United States)

    Forrest, Stephen; Qi, Xiangfei; Slootsky, Michael

    2016-06-28

    The present invention relates to efficient organic light emitting devices (OLEDs). More specifically, the present invention relates to white-emitting OLEDs, or WOLEDs. The devices of the present invention employ three emissive sub-elements, typically emitting red, green and blue, to sufficiently cover the visible spectrum. The sub-elements are separated by charge generating layers.

  8. OLED Luminaire with Panel Integrated Drivers and Advanced Controls

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Michael [Acuity Brands Lighting, Inc., Atlanta, GA (United States); Spindler, Jeff [OLEDWorks, Rochester, NY (United States)

    2017-01-31

    For this DOE award, Acuity Brands Lighting developed a novel OLED luminaire system featuring panel-integrated drivers at each individual OLED panel. The luminaire has a base station that receives user commands and performs AC/DC conversion. A power line communication (PLC) protocol is used to provide both power and digital control to each panel. A 66-panel CanvisTM luminaire using state-of-art OLED panels based on this system was successfully constructed. This is a first demonstration of such a luminaire architecture. It is also the first known implementation of this number of independently addressable nodes with a PLC protocol. This luminaire system architecture has added benefits in the flexibility of using multiple panel vendors for a given product, forward compatibility with future panels, and reduced luminaire wiring complexity and assembly time.

  9. Studying the Attribution of LiF in OLED by the - Characteristics

    Directory of Open Access Journals (Sweden)

    Chun-lin Zhang

    2010-01-01

    Full Text Available The organic light-emitting device (OLED with simple structures of indium tin oxide (ITO/tris(8-quinolinolato aluminum (Alq3/LiF/Al and ITO/Alq3/Al was fabricated to analyze the contribution of LiF in OLED. We used the - characteristics to investigate the contribution of LiF in OLED and found that the capacitance of the above-mentioned structures was 12.5 nF and 77.5 nF, respectively. It is shown that the LiF layer affects the property of OLED resulting in the change of the capacitance of the device.

  10. Efficient p-phenylene based OLEDs with mixed interfacial exciplex emission

    International Nuclear Information System (INIS)

    Data, P.; Motyka, R.; Lapkowski, M.; Suwinski, J.; Jursenas, S.; Kreiza, G.; Miasojedovas, A.; Monkman, A.P.

    2015-01-01

    Organic electronics, mainly due to the advancement of OLED (Organic Light Emitting Diode) technology, is a fast developing research area, and has already revolutionized the displays market. This direction presents the use of exciplex emitters and thermally activated delayed fluorescence (TADF) in OLEDs. This is shown through electrochemical characterisation of six p-phenylene derivatives for application in optoelectronic devices and presents the possibility the compounds’ use as OLED emitters. In these OLED devices, it is established that selenophene based compounds with a “heavy-atom effect” can be used as potential emitters when exciplex phenomena are involved.

  11. OR.NET: a service-oriented architecture for safe and dynamic medical device interoperability.

    Science.gov (United States)

    Kasparick, Martin; Schmitz, Malte; Andersen, Björn; Rockstroh, Max; Franke, Stefan; Schlichting, Stefan; Golatowski, Frank; Timmermann, Dirk

    2018-02-23

    Modern surgical departments are characterized by a high degree of automation supporting complex procedures. It recently became apparent that integrated operating rooms can improve the quality of care, simplify clinical workflows, and mitigate equipment-related incidents and human errors. Particularly using computer assistance based on data from integrated surgical devices is a promising opportunity. However, the lack of manufacturer-independent interoperability often prevents the deployment of collaborative assistive systems. The German flagship project OR.NET has therefore developed, implemented, validated, and standardized concepts for open medical device interoperability. This paper describes the universal OR.NET interoperability concept enabling a safe and dynamic manufacturer-independent interconnection of point-of-care (PoC) medical devices in the operating room and the whole clinic. It is based on a protocol specifically addressing the requirements of device-to-device communication, yet also provides solutions for connecting the clinical information technology (IT) infrastructure. We present the concept of a service-oriented medical device architecture (SOMDA) as well as an introduction to the technical specification implementing the SOMDA paradigm, currently being standardized within the IEEE 11073 service-oriented device connectivity (SDC) series. In addition, the Session concept is introduced as a key enabler for safe device interconnection in highly dynamic ensembles of networked medical devices; and finally, some security aspects of a SOMDA are discussed.

  12. Definition of information technology architectures for continuous data management and medical device integration in diabetes.

    Science.gov (United States)

    Hernando, M Elena; Pascual, Mario; Salvador, Carlos H; García-Sáez, Gema; Rodríguez-Herrero, Agustín; Martínez-Sarriegui, Iñaki; Gómez, Enrique J

    2008-09-01

    The growing availability of continuous data from medical devices in diabetes management makes it crucial to define novel information technology architectures for efficient data storage, data transmission, and data visualization. The new paradigm of care demands the sharing of information in interoperable systems as the only way to support patient care in a continuum of care scenario. The technological platforms should support all the services required by the actors involved in the care process, located in different scenarios and managing diverse information for different purposes. This article presents basic criteria for defining flexible and adaptive architectures that are capable of interoperating with external systems, and integrating medical devices and decision support tools to extract all the relevant knowledge to support diabetes care.

  13. Architecture

    OpenAIRE

    Clear, Nic

    2014-01-01

    When discussing science fiction’s relationship with architecture, the usual practice is to look at the architecture “in” science fiction—in particular, the architecture in SF films (see Kuhn 75-143) since the spaces of literary SF present obvious difficulties as they have to be imagined. In this essay, that relationship will be reversed: I will instead discuss science fiction “in” architecture, mapping out a number of architectural movements and projects that can be viewed explicitly as scien...

  14. A Novel Lighting OLED Panel Design

    Directory of Open Access Journals (Sweden)

    Enyang Zhang

    2016-11-01

    Full Text Available A novel OLED (organic light emitting diode lighting panel, which uses a special layout design, can reduce the photolithography cycles and process costs and is more reliable. It only needs two steps of photolithography cycles, which include an ITO (InSnO compound transparent oxide pattern and insulator pattern. There is no need for the metal bus pattern of the ordinary design. The OLED device structure is a type of red–green–blue (RGB-stacked emitting layer that has a good color index and greater adjustability, which improves the performance of the device. This novel design has the same equipment and material requirement compared to the ordinary design, and it is very beneficial in terms of high volume and low-cost production. It uses a hyper driving method because the entire OLED lighting panel is divided into many sub-emitting units; if one of the sub-emitting units is burned out, it has no effect on the adjacent sub-emitting unit, so the reliability is markedly better than the ordinary design.

  15. Ole Bornedals Danmarksfilm

    DEFF Research Database (Denmark)

    Hansen, Kim Toft

    2016-01-01

    Dette kapitel sætter fokus på den politiske reception af 1864. Først viser jeg, hvordan der er en række interessante ligheder mellem Poul Henningensens Danmark (1935) og 1864; ligheder, der ikke som sådan er indholdsmæssige ud over, at både Danmark og 1864 tematiserer nogle nationale synspunkter;...... diskuterer jeg, hvorvidt Ole Bornedal selv kan siges at være kulturradikal, og i så fald på hvilken måde....

  16. Interplay between efficiency and device architecture for small molecule organic solar cells.

    Science.gov (United States)

    Williams, Graeme; Sutty, Sibi; Aziz, Hany

    2014-06-21

    Small molecule organic solar cells (OSCs) have experienced a resurgence of interest over their polymer solar cell counterparts, owing to their improved batch-to-batch (thus, cell-to-cell) reliability. In this systematic study on OSC device architecture, we investigate five different small molecule OSC structures, including the simple planar heterojunction (PHJ) and bulk heterojunction (BHJ), as well as several planar-mixed structures. The different OSC structures are studied over a wide range of donor:acceptor mixing concentrations to gain a comprehensive understanding of their charge transport behavior. Transient photocurrent decay measurements provide crucial information regarding the interplay between charge sweep-out and charge recombination, and ultimately hint toward space charge effects in planar-mixed structures. Results show that the BHJ/acceptor architecture, comprising a BHJ layer with high C60 acceptor content, generates OSCs with the highest performance by balancing charge generation with charge collection. The performance of other device architectures is largely limited by hole transport, with associated hole accumulation and space charge effects.

  17. UTBB FDSOI suitability for IoT applications: Investigations at device, design and architectural levels

    Science.gov (United States)

    Berthier, Florent; Beigne, Edith; Heitzmann, Frédéric; Debicki, Olivier; Christmann, Jean-Frédéric; Valentian, Alexandre; Billoint, Olivier; Amat, Esteve; Morche, Dominique; Chairat, Soundous; Sentieys, Olivier

    2016-11-01

    In this paper, we propose to analyze Ultra Thin Body and Box FDSOI technology suitability and architectural solutions for IoT applications and more specifically for autonomous Wireless Sensor Nodes (WSNs). As IoT applications are extremely diversified there is a strong need for flexible solutions at design, architectural level but also at technological level. Moreover, as most of those systems are recovering their energy from the environment, they are challenged by low voltage supplies and low leakage functionalities. We detail in this paper some Ultra Thin Body and Box FDSOI 28 nm characteristics and results demonstrating that this technology could be a perfect option for multidisciplinary IoT devices. Back biasing capabilities and low voltage features are investigated demonstrating efficient high speed/low leakage flexibility. In addition, architectural solutions for WSNs microcontroller are also proposed taking advantage of Ultra Thin Body and Box FDSOI characteristics for full user applicative flexibility. A partitioned architecture between an Always Responsive part with an asynchronous Wake Up Controller (WUC) managing WSN current tasks and an On Demand part with a main processor for application maintenance is presented. First results of the Always Responsive part implemented in Ultra Thin Body and Box FDSOI 28 nm are also exposed.

  18. New Optoelectronic Technology Simplified for Organic Light Emitting Diode (OLED

    Directory of Open Access Journals (Sweden)

    Andre F. S. Guedes

    2014-06-01

    Full Text Available The development of Organic Light Emitting Diode (OLED, using an optically transparent substrate material and organic semiconductor materials, has been widely utilized by the electronic industry when producing new technological products. The OLED are the base Poly (3,4-ethylenedioxythiophene, PEDOT, and Polyaniline, PANI, were deposited in Indium Tin Oxide, ITO, and characterized by UV-Visible Spectroscopy (UV-Vis, Optical Parameters (OP and Scanning Electron Microscopy (SEM. In addition, the thin film obtained by the deposition of PANI, prepared in perchloric acid solution, was identified through PANI-X1. The result obtained by UV-Vis has demonstrated that the Quartz/ITO/PEDOT/PANI-X1 layer does not have displacement of absorption for wavelengths greaters after spin-coating and electrodeposition. Thus, the spectral irradiance of the OLED informed the irradiance of 100 W/m2, and this result, compared with the standard Light Emitting Diode (LED, has indicated that the OLED has higher irradiance. After 1000 hours of electrical OLED tests, the appearance of nanoparticles visible for images by SEM, to the migration process of organic semiconductor materials, was present, then. Still, similar to the phenomenon of electromigration observed in connections and interconnections of microelectronic devices, the results have revealed a new mechanism of migration, which raises the passage of electric current in OLED.

  19. Green-emitting MADF complex for OLED applications

    Science.gov (United States)

    Klimes, Kody; Zhu, Zhi-Qiang; Holloway, Sean; Li, Jian

    2016-09-01

    In this article, we demonstrated an exceptional palladium complex that exhibits both phosphorescence and delayed fluorescence for use as an efficient emitter in OLEDs. Devices employing PdN3N achieved external quantum efficiencies in excess of 22% and remarkable device operational lifetime to 90% initial luminance estimated at over 30,000 h at a practical luminance of 100 cd/m2. Further tuning of the phosphorescent and delayed fluorescent emission should have a great impact in the development of efficient and stable emitters for deep blue or white OLEDs.

  20. The Spin Torque Lego - from spin torque nano-devices to advanced computing architectures

    Science.gov (United States)

    Grollier, Julie

    2013-03-01

    Spin transfer torque (STT), predicted in 1996, and first observed around 2000, brought spintronic devices to the realm of active elements. A whole class of new devices, based on the combined effects of STT for writing and Giant Magneto-Resistance or Tunnel Magneto-Resistance for reading has emerged. The second generation of MRAMs, based on spin torque writing : the STT-RAM, is under industrial development and should be out on the market in three years. But spin torque devices are not limited to binary memories. We will rapidly present how the spin torque effect also allows to implement non-linear nano-oscillators, spin-wave emitters, controlled stochastic devices and microwave nano-detectors. What is extremely interesting is that all these functionalities can be obtained using the same materials, the exact same stack, simply by changing the device geometry and its bias conditions. So these different devices can be seen as Lego bricks, each brick with its own functionality. During this talk, I will show how spin torque can be engineered to build new bricks, such as the Spintronic Memristor, an artificial magnetic nano-synapse. I will then give hints on how to assemble these bricks in order to build novel types of computing architectures, with a special focus on neuromorphic circuits. Financial support by the European Research Council Starting Grant NanoBrain (ERC 2010 Stg 259068) is acknowledged.

  1. Triarylborane-Based Materials for OLED Applications

    Directory of Open Access Journals (Sweden)

    Gulsen Turkoglu

    2017-09-01

    Full Text Available Multidisciplinary research on organic fluorescent molecules has been attracting great interest owing to their potential applications in biomedical and material sciences. In recent years, electron deficient systems have been increasingly incorporated into fluorescent materials. Triarylboranes with the empty p orbital of their boron centres are electron deficient and can be used as strong electron acceptors in conjugated organic fluorescent materials. Moreover, their applications in optoelectronic devices, energy harvesting materials and anion sensing, due to their natural Lewis acidity and remarkable solid-state fluorescence properties, have also been investigated. Furthermore, fluorescent triarylborane-based materials have been commonly utilized as emitters and electron transporters in organic light emitting diode (OLED applications. In this review, triarylborane-based small molecules and polymers will be surveyed, covering their structure-property relationships, intramolecular charge transfer properties and solid-state fluorescence quantum yields as functional emissive materials in OLEDs. Also, the importance of the boron atom in triarylborane compounds is emphasized to address the key issues of both fluorescent emitters and their host materials for the construction of high-performance OLEDs.

  2. Manufacturing Process for OLED Integrated Substrate

    Energy Technology Data Exchange (ETDEWEB)

    Hung, Cheng-Hung [Vitro Flat Glass LLC, Cheswick, PA (United States). Glass Technology Center

    2017-03-31

    The main objective of this project was to develop a low-cost integrated substrate for rigid OLED solid-state lighting produced at a manufacturing scale. The integrated substrates could include combinations of soda lime glass substrate, light extraction layer, and an anode layer (i.e., Transparent Conductive Oxide, TCO). Over the 3+ year course of the project, the scope of work was revised to focus on the development of a glass substrates with an internal light extraction (IEL) layer. A manufacturing-scale float glass on-line particle embedding process capable of producing an IEL glass substrate having a thickness of less than 1.7mm and an area larger than 500mm x 400mm was demonstrated. Substrates measuring 470mm x 370mm were used in the OLED manufacturing process for fabricating OLED lighting panels in single pixel devices as large as 120.5mm x 120.5mm. The measured light extraction efficiency (calculated as external quantum efficiency, EQE) for on-line produced IEL samples (>50%) met the project’s initial goal.

  3. Multilevel and Hybrid Architecture for Device Abstraction and Context Information Management in Smart Home Environments

    Science.gov (United States)

    Peláez, Víctor; González, Roberto; San Martín, Luis Ángel; Campos, Antonio; Lobato, Vanesa

    Hardware device management, and context information acquisition and abstraction are key factors to develop the ambient intelligent paradigm in smart homes. This work presents an architecture that addresses these two problems and provides a usable framework to develop applications easily. In contrast to other proposals, this work addresses performance issues specifically. Results show that the execution performance of the developed prototype is suitable for deployment in a real environment. In addition, the modular design of the system allows the user to develop applications using different techniques and different levels of abstraction.

  4. Thin Film Packaging Solutions for High Efficiency OLED Lighting Products

    Energy Technology Data Exchange (ETDEWEB)

    None

    2008-06-30

    The objective of the 'Thin Film Packaging Solutions for High Efficiency OLED Lighting Products' project is to demonstrate thin film packaging solutions based on SiC hermetic coatings that, when applied to glass and plastic substrates, support OLED lighting devices by providing longer life with greater efficiency at lower cost than is currently available. Phase I Objective: Demonstrate thin film encapsulated working phosphorescent OLED devices on optical glass with lifetime of 1,000 hour life, CRI greater than 75, and 15 lm/W. Phase II Objective: Demonstrate thin film encapsulated working phosphorescent OLED devices on plastic or glass composite with 25 lm/W, 5,000 hours life, and CRI greater than 80. Phase III Objective: Demonstrate 2 x 2 ft{sup 2} thin film encapsulated working phosphorescent OLED with 40 lm/W, 10,000 hour life, and CRI greater than 85. This report details the efforts of Phase III (Budget Period Three), a fourteen month collaborative effort that focused on optimization of high-efficiency phosphorescent OLED devices and thin-film encapsulation of said devices. The report further details the conclusions and recommendations of the project team that have foundation in all three budget periods for the program. During the conduct of the Thin Film Packaging Solutions for High Efficiency OLED Lighting Products program, including budget period three, the project team completed and delivered the following achievements: (1) a three-year marketing effort that characterized the near-term and longer-term OLED market, identified customer and consumer lighting needs, and suggested prototype product concepts and niche OLED applications lighting that will give rise to broader market acceptance as a source for wide area illumination and energy conservation; (2) a thin film encapsulation technology with a lifetime of nearly 15,000 hours, tested by calcium coupons, while stored at 16 C and 40% relative humidity ('RH'). This encapsulation technology

  5. OR.NET RT: how service-oriented medical device architecture meets real-time communication.

    Science.gov (United States)

    Pfeiffer, Jonas H; Kasparick, Martin; Strathen, Benjamin; Dietz, Christian; Dingler, Max E; Lueth, Tim C; Timmermann, Dirk; Radermacher, Klaus; Golatowski, Frank

    2018-02-23

    Today's landscape of medical devices is dominated by stand-alone systems and proprietary interfaces lacking cross-vendor interoperability. This complicates or even impedes the innovation of novel, intelligent assistance systems relying on the collaboration of medical devices. Emerging approaches use the service-oriented architecture (SOA) paradigm based on Internet protocol (IP) to enable communication between medical devices. While this works well for scenarios with no or only soft timing constraints, the underlying best-effort communication scheme is insufficient for time critical data. Real-time (RT) networks are able to reliably guarantee fixed latency boundaries, for example, by using time division multiple access (TDMA) communication patterns. However, deterministic RT networks come with their own limitations such as tedious, inflexible configuration and a more restricted bandwidth allocation. In this contribution we overcome the drawbacks of both approaches by describing and implementing mechanisms that allow the two networks to interact. We introduce the first implementation of a medical device network that offers hard RT guarantees for control and sensor data and integrates into SOA networks. Based on two application examples we show how the flexibility of SOA networks and the reliability of RT networks can be combined to achieve an open network infrastructure for medical devices in the operating room (OR).

  6. Energy-cascade organic photovoltaic devices incorporating a host-guest architecture.

    Science.gov (United States)

    Menke, S Matthew; Holmes, Russell J

    2015-02-04

    In planar heterojunction organic photovoltaic devices (OPVs), broad spectral coverage can be realized by incorporating multiple molecular absorbers in an energy-cascade architecture. Here, this approach is combined with a host-guest donor layer architecture previously shown to optimize exciton transport for the fluorescent organic semiconductor boron subphthalocyanine chloride (SubPc) when diluted in an optically transparent host. In order to maximize the absorption efficiency, energy-cascade OPVs that utilize both photoactive host and guest donor materials are examined using the pairing of SubPc and boron subnaphthalocyanine chloride (SubNc), respectively. In a planar heterojunction architecture, excitons generated on the SubPc host rapidly energy transfer to the SubNc guest, where they may migrate toward the dissociating, donor-acceptor interface. Overall, the incorporation of a photoactive host leads to a 13% enhancement in the short-circuit current density and a 20% enhancement in the power conversion efficiency relative to an optimized host-guest OPV combining SubNc with a nonabsorbing host. This work underscores the potential for further design refinements in planar heterojunction OPVs and demonstrates progress toward the effective separation of functionality between constituent OPV materials.

  7. Mixed-ligand Al complex—a new approach for more high efficient OLEDs

    International Nuclear Information System (INIS)

    Petrova, Petia K.; Tomova, Reni L.; Stoycheva-Topalova, Rumiana T.; Kaloyanova, Stefka S.; Deligeorgiev, Todor G.

    2012-01-01

    The mixed-ligand Aluminum bis(8-hydroxyquinoline) acetylacetonate (Alq 2 Acac) complex was presented and its performance as electroluminescent and electron transporting layer for OLED was studied. The photophysical properties of the novel complex were investigated and compared with the properties of the parent Alq 3 . Highly efficient OLED based on the mixed-ligand Al complex was developed with two times higher luminescence and efficiency compared to the identical OLED based on the conventional Alq 3 The better performance of the devices make the novel Al complex a very promising material for OLEDs. - Highlights: ► A novel electroluminescent Alq 2 Acac complex is presented as material for OLED. ► Electroluminescent emission of Alq 2 Acac is very similar to that of commercial Alq 3 . ► Devices with Alq 2 Acac show better characteristics compared to those with Alq 3 .

  8. Maailmaparandajad / Ole Ry, Susanne Andres

    Index Scriptorium Estoniae

    Ry, Ole

    2012-01-01

    Terapeudid Ole Ry ja Susanne Andres räägivad Dr David Berceli loodud TRE (Tension & Trauma Releasing Exercises) harjutuste kasutamise kogemusest erinevate psüühiliste traumade ja pingetega klientide tervise parandamisel

  9. Recent advances in AM OLED technologies for application to aerospace and military systems

    Science.gov (United States)

    Sarma, Kalluri R.; Roush, Jerry; Chanley, Charles

    2012-06-01

    While initial AM OLED products have been introduced in the market about a decade ago, truly successful commercialization of OLEDs has started only a couple of years ago, by Samsung Mobile Display (SMD), with small high performance displays for smart phone applications. This success by Samsung has catalyzed significant interest in AM OLED technology advancement and commercialization by other display manufacturers. Currently, significant manufacturing capacity for AM OLED displays is being established by the industry to serve the growing demand for these displays. The current development in the AM OLED industry are now focused on the development and commercialization of medium size (~10") AM OLED panels for Tablet PC applications and large size (~55") panels for TV applications. This significant progress in commercialization of AM OLED technology is enabled by major advances in various enabling technologies that include TFT backplanes, OLED materials and device structures and manufacturing know-how. In this paper we will discuss these recent advances, particularly as they relate to supporting high performance applications such as aerospace and military systems, and then discuss the results of the OLED testing for aerospace applications.

  10. A Secure and Robust Connectivity Architecture for Smart Devices and Applications

    Directory of Open Access Journals (Sweden)

    Lee YangSun

    2011-01-01

    Full Text Available Convergence environments and technologies are urgently coming close to our life with various wireless communications and smart devices in order to provide many benefits such as connectivity, usability, mobility, portability, and flexibility as well as lower installation and maintenance costs. Convergence has brought important change not only in the way we live but also in the way we think. It is the progress towards the attempt to create and to evolve new valuable services through the device convergence and fusion of in-home, office, and various environments around the personal mobile apparatus. Based on the dynamic trends of convergence, it is widely argued that the increased requirements on secure and robust connectivity between a variety of mobile devices and their applications provide us the era of real pervasive computing environment. Thus, in this paper, we present a novel connectivity architecture using RF4CE-(Radio Frequency for Consumer Electronics- based wireless zero-configuration and enhanced key agreement approach. We analyze the security and performance of our proposed approach by the development of the prototype H/W and the construction of a testbed with CE and mobile devices.

  11. Organic light emitting diodes (OLEDS) and OLED-based structurally integrated optical sensors

    International Nuclear Information System (INIS)

    Cai, Yuankun

    2010-01-01

    General introduction to OLED basics and OLED-based structurally integrated sensors was provided in chapter 1 and chapter 2. As discussed in chapter 3, OLEDs were developed or improved using novel engineering methods for better charge injection (increased by over 1 order of magnitude) and efficiency. As the excitation sources, these OLEDs have preferred characteristics for sensor applications, including narrowed emission, emission at desired wavelength, and enhanced output for reduced EL background, higher absorption and improved device lifetime. In addition to OLEDs with desired performance, sensor integration requires oxidase immobilization with the sensor film for O 2 -based biological and chemical sensing. Nanoparticles such as ZnO have large surface area and high isoelectric point (∼9.5), which favors enzyme immobilization via physical adsorption as well as Coulombic bonding. In chapter 4, it was demonstrated that ZnO could be used for this purpose, although future work is needed to further bond the ZnO to the sensor film. In chapter 5, single unit sensor was extended to multianalyte parallel sensing based on an OLED platform, which is compact and integrated with silicon photodiodes and electronics. Lactate and glucose were simultaneously monitored with a low limit of detection 0.02 mM, fast response time (∼ 1 minute) and dynamic range from 0-8.6 ppm of dissolved oxygen. As discovered in previous work, the dynamic range covers 0-100% gas phase O 2 or 0-40 ppm dissolved oxygen at room temperature. PL decay curve, which is used to extract the decay time, is usually not a simple exponential at high O 2 concentration, which indicates that O 2 is not equally accessible for different luminescent sites. This creates a challenge for data analysis, which however was successfully processed by stretched exponential as shown in chapter 6. This also provides an insight about the distribution of O 2 :dye collisional quenching rate due to microheterogeneity. Effect of Ti

  12. Organic light emitting diodes (OLEDS) and OLED-based structurally integrated optical sensors

    Energy Technology Data Exchange (ETDEWEB)

    Cai, Yuankun [Iowa State Univ., Ames, IA (United States)

    2010-01-01

    General introduction to OLED basics and OLED-based structurally integrated sensors was provided in chapter 1 and chapter 2. As discussed in chapter 3, OLEDs were developed or improved using novel engineering methods for better charge injection (increased by over 1 order of magnitude) and efficiency. As the excitation sources, these OLEDs have preferred characteristics for sensor applications, including narrowed emission, emission at desired wavelength, and enhanced output for reduced EL background, higher absorption and improved device lifetime. In addition to OLEDs with desired performance, sensor integration requires oxidase immobilization with the sensor film for O2-based biological and chemical sensing. Nanoparticles such as ZnO have large surface area and high isoelectric point (~9.5), which favors enzyme immobilization via physical adsorption as well as Coulombic bonding. In chapter 4, it was demonstrated that ZnO could be used for this purpose, although future work is needed to further bond the ZnO to the sensor film. In chapter 5, single unit sensor was extended to multianalyte parallel sensing based on an OLED platform, which is compact and integrated with silicon photodiodes and electronics. Lactate and glucose were simultaneously monitored with a low limit of detection 0.02 mM, fast response time (~1 minute) and dynamic range from 0-8.6 ppm of dissolved oxygen. As discovered in previous work, the dynamic range covers 0-100% gas phase O2 or 0-40 ppm dissolved oxygen at room temperature. PL decay curve, which is used to extract the decay time, is usually not a simple exponential at high O2 concentration, which indicates that O2 is not equally accessible for different luminescent sites. This creates a challenge for data analysis, which however was successfully processed by stretched exponential as shown in chapter 6. This also provides an insight about the distribution of O2:dye collisional quenching

  13. Development of a charge transport model for white OLEDs

    NARCIS (Netherlands)

    Vries, de R.J.

    2012-01-01

    Organic light-emitting diodes (OLEDs) are promising candidates for future lighting applications since they can be made ultra-thin, color-tunable and exible. Improving their e??ciency is an important challenge in the ??eld of organic electronics. The availability of a device model can make the

  14. Simulations, measurements, and optimization of OLEDs with scattering layer

    NARCIS (Netherlands)

    Altazin, S.; Reynaud, C.; Mayer, U.M.; Lanz, T.; Lapagna, K.; Knaack, R.; Peninck, L.; Kirsch, C.; Pernstich, K.P.; Harkema, S.; Hermes, D.; Ruhstaller, B.

    2015-01-01

    A multi-scale optical model for organic light-emitting devices containing scattering layers is presented. This model describes the radiation of embedded oscillating dipoles and scattering from spherical particles. After successful model validation with experiments on a top-emitting white OLED, we

  15. Optical characterization of OLED emitter properties by radiation pattern analyses

    Energy Technology Data Exchange (ETDEWEB)

    Flaemmich, Michael

    2011-09-08

    Researches in both, academia and industry are investigating optical loss channels in OLED layered systems by means of optical simulation tools in order to derive promising concepts for a further enhancement of the overall device performance. Besides other factors, the prospects of success of such optimization strategies rely severely on the credibility of the optical input data. The present thesis provides a guideline to measure the active optical properties of OLED emitter materials in situ by radiation pattern analyses. Reliable and widely applicable methods are introduced to determine the internal electroluminescence spectrum, the profile of the emission zone, the dipole emitter orientation, and the internal luminescence quantum efficiency of emissive materials from the optical far field emission of OLEDs in electrical operation. The proposed characterization procedures are applied to sets of OLEDs containing both, fluorescent polymeric materials as well as phosphorescent small-molecular emitters, respectively. On the one hand, quite expected results are obtained. On the other hand, several novel and truly surprising results are found. Most importantly, this thesis contains the first report of a non-isotropic, mainly parallel emitter orientation in a phosphorescent small-molecular guest-host system (Ir(MDQ)2(acac) in a-NPD). Due to the latter result, emitter orientation based optimization of phosphorescent OLEDs seems to be within reach. Since parallel dipoles emit preferably into air, the utilization of smart emissive materials with advantageous molecular orientation is capable to boost the efficiency of phosphorescent OLEDs by 50%. Materials design, the influence of the matrix material and the substrate, as well as film deposition conditions are just a few parameters that need to be studied further in order to exploit the huge potential of the dipole emitter orientation in phosphorescent OLEDs.

  16. Comparative study of graphene and its derivative materials as an electrode in OLEDs

    Science.gov (United States)

    Srivastava, Anshika; Kumar, Brijesh

    2018-04-01

    In current scenario, the organic materials have given a revolutionary evolution in the electronics industry. As, the organic light emitting diodes (OLEDs) have almost replaced the conventional technologies due to the use of organic based materials. However, the next generations OLEDs are intensively desired nowadays for high definition display technology. There are various concern involved in the successful design of OLEDs. Electrodes are one of the electrical conductors, which play a vital role in the construction of OLEDs. The performance of OLED is majorly affected by the material used for electrodes. Due to the requirement of transparent, flexible and inexpensive anodes in bottom emissive OLEDs, ITO was replaced by graphene material. Graphene is a single layer 2-dimensional transparent carbon allotrope which showed prodigious potential to escalate the device performance. Although graphene demonstrated impressive characteristics in various applications, it showed unfavorable work function for many other devices. Thus, derivative materials of graphene such as graphene oxide, graphane and β - graphdiyne were synthesized by several researchers. By comparing graphene and its derivatives as an anode of OLEDs, it has been found that graphene oxide showed the preeminent performance among all. In this paper, all the comparisons are investigated by using a standard device constructed by piling layers of anode/ m_MTDATA/ NPB/ Alq3: QAD/ Alq3/ cathode in TCAD ATLAS device simulator.

  17. White top emitting OLED with angle independent emission characteristic

    Energy Technology Data Exchange (ETDEWEB)

    Thomschke, Michael; Freitag, Patricia; Schwartz, Gregor; Nitsche, Robert; Walzer, Karsten; Leo, Karl [Technische Universitaet Dresden, Institut fuer Angewandte Photophysik, Georg-Baehr-Strasse 1, 01062 Dresden (Germany)

    2008-07-01

    The general device structure of a top emitting organic light emitting diode (OLED) consists of several organic layers sandwiched in between two metal contacts, with the top one being semitransparent for light outcoupling reasons. Due to the high reflectivity of the electrodes, strong microcavity effects occur which lead to a preferred emission of light of a certain wavelength with main outcoupling in forward direction. This creates rather narrow emission bands, accompanied by strong spectral shifts upon viewing angle variation. By using an organic capping layer on top of the semitransparent metal contact, this unwanted effect can be reduced. This is important especially for white light emission for the use of OLEDs in future lighting applications. Our optical simulations show that the strong angular dependence of the emission color almost vanishes. To verify the simulations we study white top emitting OLEDs based on an approach which are adapted to the top emitting case.

  18. Motion-sensor fusion-based gesture recognition and its VLSI architecture design for mobile devices

    Science.gov (United States)

    Zhu, Wenping; Liu, Leibo; Yin, Shouyi; Hu, Siqi; Tang, Eugene Y.; Wei, Shaojun

    2014-05-01

    With the rapid proliferation of smartphones and tablets, various embedded sensors are incorporated into these platforms to enable multimodal human-computer interfaces. Gesture recognition, as an intuitive interaction approach, has been extensively explored in the mobile computing community. However, most gesture recognition implementations by now are all user-dependent and only rely on accelerometer. In order to achieve competitive accuracy, users are required to hold the devices in predefined manner during the operation. In this paper, a high-accuracy human gesture recognition system is proposed based on multiple motion sensor fusion. Furthermore, to reduce the energy overhead resulted from frequent sensor sampling and data processing, a high energy-efficient VLSI architecture implemented on a Xilinx Virtex-5 FPGA board is also proposed. Compared with the pure software implementation, approximately 45 times speed-up is achieved while operating at 20 MHz. The experiments show that the average accuracy for 10 gestures achieves 93.98% for user-independent case and 96.14% for user-dependent case when subjects hold the device randomly during completing the specified gestures. Although a few percent lower than the conventional best result, it still provides competitive accuracy acceptable for practical usage. Most importantly, the proposed system allows users to hold the device randomly during operating the predefined gestures, which substantially enhances the user experience.

  19. Solution processed ternary blend nano-composite charge regulation layer to enhance inverted OLED performances

    Science.gov (United States)

    Kaçar, Rifat; Mucur, Selin Pıravadılı; Yıldız, Fikret; Dabak, Salih; Tekin, Emine

    2018-04-01

    Inverted bottom-emission organic light emitting diodes (IBOLEDs) have attracted increasing attention due to their exceptional air stability and applications in active-matrix displays. For gaining high IBOLED device efficiencies, it is crucial to develop an effective strategy to make the bottom electrode easy for charge injection and transport. Charge selectivity, blocking the carrier flow towards the unfavourable side, plays an important role in determining charge carrier balance and accordingly radiative recombination efficiency. It is therefore highly desirable to functionalize an interfacial layer which will perform many different tasks simultaneously. Here, we contribute to the hole-blocking ability of the zinc oxide/polyethyleneimine (ZnO:PEI) nano-composite (NC) interlayer with the intention of increasing the OLED device efficiency. With this purpose in mind, a small amount of 1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBi) was added as a hole-blocking molecule into the binary blend of ZnO and PEI solution. The device with a ternary ZnO:PEI:TPBi NC interlayer achieved a maximum current efficiency of 38.20 cd A-1 and a power efficiency of 34.29 lm W-1 with a luminance of 123 200 cd m-2, which are high performance parameters for inverted device architecture. The direct comparisons of device performances incorporating ZnO only, ZnO/PEI bilayers, and ZnO:PEI binary NC counterparts were also performed, which shed light on the origin of device performance enhancement.

  20. Electrical characterization of organic thin film transistors and alternative device architectures

    Science.gov (United States)

    Newman, Christopher R.

    In the last 10--15 years, organic semiconductors have evolved from experimental curiosities into viable alternatives for practical applications involving large-area and low-cost electronics such as display backplanes, electronic paper, radio frequency identification (RFID) tags, and solar cells. Many of the initially-stated goals in this field have been achieved; organic semconductors have demonstrated performance comparable to or greater than amorphous silicon (a-Si), the entrenched technology for most of the applications listed above. At present, the major obstacles remaining to commercialization of devices based on organic semiconductors involve material stability, processing considerations and optimization of the other device components (e.g. metal contacts and dielectric materials). Despite these technical achievements, significant gaps remain in our understanding of the underlying transport physics in these devices. This thesis summarizes experiments performed on organic field-effect transistors (OFETs) in an attempt to address some of these knowledge gaps. The FET, in addition to being a very useful device for practical applications (such as the driving elements in pixel backplanes), is also a very flexible architecture from an experimental standpoint. The presence of a capacitively-coupled gate electrode allows the investigation of transport physics as a function of carrier concentration. For devices in which non-idealities (i.e. carrier traps) largely dictate the observed characteristics, this is a very useful feature. Although practical OFETs are fabricated as conventional single-gate structures on an organic thin film (OTFTs), more exotic structures can often provide insights that standard OTFTs cannot. Specifically, single-crystal OFETs allow the investigation of carrier transport in the absence of grain boundaries, and double-gated OTFTs facilitate the investigation and comparison of properties across two discrete interfaces. One of the remaining

  1. OLED microdisplays technology and applications

    CERN Document Server

    Templier, François

    2014-01-01

    Microdisplays are displays requiring optical magnification and OLEDs (Organic Light-Emitting Diode) are self-emitting displays where each pixel includes a LED made of organic material, in general composed of small-molecule organic material. This title reviews in detail how OLED microdisplays are made as well as how they are used. All aspects from theory to application will be addressed: basic principles, display design, display fabrication, operation and performances, present and future applications. The book will be useful to anyone interested in this rapidly developing field, such as studen

  2. Ole Rømer-Observatoriet

    DEFF Research Database (Denmark)

    Buhl, Hans; Knudsen, Ole J.; Nielsen, Axel V.

    Siden 1911 har der ligget et astronomisk observatorium i Århus. Ole Rømer-Observatoriet blev efter en turbulent start drevet af kommunen, indtil Aarhus Universitet i 1956 overtog det. Der har fra tid til anden været både kontroverser og trusler om lukning, men arbejdet på observatoriet har også...... fortæller museumsinspektør Hans Buhl og planetarieleder Ole J. Knudsen, begge Steno Museet, de næste 95 år af observatoriets brogede historie....

  3. Approach to Low-Cost High-Efficiency OLED Lighting. Building Technologies Solid State Lighting (SSL) Program Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Pei, Qibing [Univ. of California, Los Angeles, CA (United States). Dept. of Materials Science and Engineering

    2017-10-06

    This project developed an integrated substrate which organic light emitting diode (OLED) panel developers could employ the integrated substrate to fabricate OLED devices with performance and projected cost meeting the MYPP targets of the Solid State Lighting Program of the Department of Energy. The project optimized the composition and processing conditions of the integrated substrate for OLED light extraction efficiency and overall performance. The process was further developed for scale up to a low-cost process and fabrication of prototype samples. The encapsulation of flexible OLEDs based on this integrated substrate was also investigated using commercial flexible barrier films.

  4. Mechanistic study on black and grey spot growth in OLEDs performed on laser-ablated pinholes in the cathode

    NARCIS (Netherlands)

    Weijer, P. van de; Bouten, P.C.P.; Fledderus, H.; Janssen, R.R.; Winter, S.H.P.M. de; Akkerman, H.B.

    2017-01-01

    Local laser ablation of the cathode of OLEDs has been applied to create a population of pinholes of the same size. This enables the direct comparison at different conditions of black spots and grey spots in the emission of OLEDs as a result of water ingress into the device. We confirmed earlier

  5. Software architecture as a freedom for 3D content providers and users along with independency on purposes and used devices

    Science.gov (United States)

    Sultana, Razia; Christ, Andreas; Meyrueis, Patrick

    2014-05-01

    The improvements in the hardware and software of communication devices have allowed running Virtual Reality (VR) and Augmented Reality (AR) applications on those. Nowadays, it is possible to overlay synthetic information on real images, or even to play 3D on-line games on smart phones or some other mobile devices. Hence the use of 3D data for business and specially for education purposes is ubiquitous. Due to always available at hand and always ready to use properties of mobile phones, those are considered as most potential communication devices. The total numbers of mobile phone users are increasing all over the world every day and that makes mobile phones the most suitable device to reach a huge number of end clients either for education or for business purposes. There are different standards, protocols and specifications to establish the communication among different communication devices but there is no initiative taken so far to make it sure that the send data through this communication process will be understood and used by the destination device. Since all the devices are not able to deal with all kind of 3D data formats and it is also not realistic to have different version of the same data to make it compatible with the destination device, it is necessary to have a prevalent solution. The proposed architecture in this paper describes a device and purpose independent 3D data visibility any time anywhere to the right person in suitable format. There is no solution without limitation. The architecture is implemented in a prototype to make an experimental validation of the architecture which also shows the difference between theory and practice.

  6. Ole Søndergaards skriftdesign

    DEFF Research Database (Denmark)

    Ejlers, Steen Erik

    2005-01-01

    Grafikeren Ole Søndergaard (f. 1937) er oprindeligt uddannet som skiltemaler. Senere blev han elev af navnkundige skriftformgiver, Kunstakademiets første designprofessor, arkitekturen Gunnar Biilmann Petersen. I 1970'erne etablerede Ole Søndergaard, efter nogle år som medarbejder på Naur Klints...... tegnestue, egen tegnestue i Helsingør. Tegnestuen har i årenes løb stået for mangfoldige grafiske arbejder, hvor Ole Søndergaard ofte selv har tegnet de anvendte logo- og skilteskrifter. Skriftfamilien FF Signa, der fra 2000 er blevet udgivet på FontShop International, er Søndergaards første komplette...... digitale skriftfamilie - med mangfoldige anvendelsemuligheder. Forud ligger adskillige års arbejde, bl.a. støttet af Statens Kunstfond. Artiklen beskriver Biilmanns skole, Ole Søndergaards "før-digitale" alfabeter til bl.a. Helsingør Kommune og Knud Rasmussen-monumentet (på Strandvejen ved Klampenborg nord...

  7. Strategies for increasing the efficiency of heterojunction organic solar cells: material selection and device architecture.

    Science.gov (United States)

    Heremans, Paul; Cheyns, David; Rand, Barry P

    2009-11-17

    Thin-film blends or bilayers of donor- and acceptor-type organic semiconductors form the core of heterojunction organic photovoltaic cells. Researchers measure the quality of photovoltaic cells based on their power conversion efficiency, the ratio of the electrical power that can be generated versus the power of incident solar radiation. The efficiency of organic solar cells has increased steadily in the last decade, currently reaching up to 6%. Understanding and combating the various loss mechanisms that occur in processes from optical excitation to charge collection should lead to efficiencies on the order of 10% in the near future. In organic heterojunction solar cells, the generation of photocurrent is a cascade of four steps: generation of excitons (electrically neutral bound electron-hole pairs) by photon absorption, diffusion of excitons to the heterojunction, dissociation of the excitons into free charge carriers, and transport of these carriers to the contacts. In this Account, we review our recent contributions to the understanding of the mechanisms that govern these steps. Starting from archetype donor-acceptor systems of planar small-molecule heterojunctions and solution-processed bulk heterojunctions, we outline our search for alternative materials and device architectures. We show that non-planar phthalocynanines have appealing absorption characteristics but also have reduced charge carrier transport. As a result, the donor layer needs to be ultrathin, and all layers of the device have to be tuned to account for optical interference effects. Using these optimization techniques, we illustrate cells with 3.1% efficiency for the non-planar chloroboron subphthalocyanine donor. Molecules offering a better compromise between absorption and carrier mobility should allow for further improvements. We also propose a method for increasing the exciton diffusion length by converting singlet excitons into long-lived triplets. By doping a polymer with a

  8. From black box to toolbox: Outlining device functionality, engagement activities, and the pervasive information architecture of mHealth interventions

    Directory of Open Access Journals (Sweden)

    Brian G. Danaher

    2015-03-01

    Full Text Available mHealth interventions that deliver content via mobile phones represent a burgeoning area of health behavior change. The current paper examines two themes that can inform the underlying design of mHealth interventions: (1 mobile device functionality, which represents the technological toolbox available to intervention developers; and (2 the pervasive information architecture of mHealth interventions, which determines how intervention content can be delivered concurrently using mobile phones, personal computers, and other devices. We posit that developers of mHealth interventions will be able to better achieve the promise of this burgeoning arena by leveraging the toolbox and functionality of mobile devices in order to engage participants and encourage meaningful behavior change within the context of a carefully designed pervasive information architecture.

  9. From black box to toolbox: Outlining device functionality, engagement activities, and the pervasive information architecture of mHealth interventions.

    Science.gov (United States)

    Danaher, Brian G; Brendryen, Håvar; Seeley, John R; Tyler, Milagra S; Woolley, Tim

    2015-03-01

    mHealth interventions that deliver content via mobile phones represent a burgeoning area of health behavior change. The current paper examines two themes that can inform the underlying design of mHealth interventions: (1) mobile device functionality, which represents the technological toolbox available to intervention developers; and (2) the pervasive information architecture of mHealth interventions, which determines how intervention content can be delivered concurrently using mobile phones, personal computers, and other devices. We posit that developers of mHealth interventions will be better able to achieve the promise of this burgeoning arena by leveraging the toolbox and functionality of mobile devices in order to engage participants and encourage meaningful behavior change within the context of a carefully designed pervasive information architecture.

  10. Development of functional nano-particle layer for highly efficient OLED

    Science.gov (United States)

    Lee, Jae-Hyun; Kim, Min-Hoi; Choi, Haechul; Choi, Yoonseuk

    2015-12-01

    Organic light emitting diodes (OLEDs) are now widely commercialized in market due to many advantages such as possibility of making thin or flexible devices. Nevertheless there are still several things to obtain the high quality flexible OLEDs, one of the most important issues is the light extraction of the device. It is known that OLEDs have the typical light loss such as the waveguide loss, plasmon absorption loss and internal total reflection. In this paper, we demonstrate the one-step processed light scattering films with aluminum oxide nano-particles and polystyrene matrix composite to achieve highly efficient OLEDs. Optical characteristics and surface roughness of light scattering film was optimized by changing the mixing concentration of Al2O3 nano-particles and investigated with the atomic force microscopy and hazemeter, respectively.

  11. Enhancement of efficiency and stability of phosphorescent OLEDs based on heterostructured light-emitting layers

    Energy Technology Data Exchange (ETDEWEB)

    Chin, Byung Doo, E-mail: bdchin@dankook.ac.kr [Department of Polymer Science and Engineering and Center for Photofunctional Energy Materials, Dankook University, Jukjeon-dong, Suji-gu, Yongin-si, Gyeonggi-do 448-701 (Korea, Republic of)

    2011-03-23

    The light-emitting efficiency and stability of a phosphorescent organic light-emitting device (OLED), whose emission characteristics are strongly dominated not only by the energy transfer but also by the charge carrier trapping influenced by heterostructured emissive layers, are studied. The variation of the material combination of the heterostructured emitter, both for mixed and double layer configuration, affects the charge injection behaviour, luminous efficiency and stability. Both double and mixed emitter configurations yield low-voltage and high-efficiency behaviour (51 lm W{sup -1} at 1000 cd m{sup -2}; 30 lm W{sup -1} at 10 000 cd m{sup -2}). Such an improvement in power efficiency at elevated brightness is sufficiently universal, while the enhancement of device half-lifetime is rather sensitive to the circumstantial layout of heterostructural emitters. With an optimal mixture of hole-transport type and electron-transport type, a half-lifetime of more than 2500 h at 4000 cd m{sup -2} is obtained, which is 8 times the half-lifetime of control devices with a single emitter structure. The origin and criterion for enhancement of efficiency and lifetime are discussed in terms of the carrier transport behaviour with a specific device architecture.

  12. Characteristics of indium zinc oxide films deposited using the facing targets sputtering method for OLEDs applications

    International Nuclear Information System (INIS)

    Rim, Y.S.; Kim, H.J.; Kim, K.H.

    2010-01-01

    The amorphous indium zinc oxide (IZO) thin films were deposited on polyethersulfone (PES) and glass substrates using the facing targets sputtering (FTS) system. The electrical, optical and structural properties of the IZO thin films deposited as functions of sputtering parameters on the glass and PES substrates. An optimal IZO deposition condition is fabricated for organic light-emitting device (OLED) based on glass and PES. The amorphous IZO anode-based OLEDs show superior current density and luminance characteristics.

  13. Color in the corners: ITO-free white OLEDs with angular color stability.

    Science.gov (United States)

    Gaynor, Whitney; Hofmann, Simone; Christoforo, M Greyson; Sachse, Christoph; Mehra, Saahil; Salleo, Alberto; McGehee, Michael D; Gather, Malte C; Lüssem, Björn; Müller-Meskamp, Lars; Peumans, Peter; Leo, Karl

    2013-08-07

    High-efficiency white OLEDs fabricated on silver nanowire-based composite transparent electrodes show almost perfectly Lambertian emission and superior angular color stability, imparted by electrode light scattering. The OLED efficiencies are comparable to those fabricated using indium tin oxide. The transparent electrodes are fully solution-processable, thin-film compatible, and have a figure of merit suitable for large-area devices. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Advances in OLED/OPD-based sensors and spectrometer-on-a-chip (Conference Presentation)

    Science.gov (United States)

    Shinar, Joseph; Kaudal, Rajiv; Manna, Eeshita; Fungura, Fadzai; Shinar, Ruth

    2016-09-01

    We describe ongoing advances toward achieving all-organic optical sensors and a spectrometer on a chip. Two-dimensional combinatorial arrays of microcavity OLEDs (μcOLEDs) with systematically varying optical cavity lengths are fabricated on a single chip by changing the thickness of different organic and/or spacer layers sandwiched between two metal electrodes (one very thin) that form the cavity. The broad spectral range is achieved by utilizing materials that result in white OLEDs (WOLEDs) when fabricated on a standard ITO substrate. The tunable and narrower emissions from the μcOLEDs serve as excitation sources in luminescent sensors and in monitoring light absorption. For each wavelength, the light from the μcOLED is partially absorbed by a sample under study and the light emitted by an electronically excited sample, or the transmitted light is detected by a photodetector (PD). To obtain a compact monitor, an organic PD (OPD) or a perovskite-based PD is integrated with the μcOLED array. We show the potential of encompassing a broader wavelength range by using WOLED materials to fabricate the μcOLEDs. The utility of the all-organic analytical devices is demonstrated by monitoring oxygen, and bioanalytes based on oxygen detection, as well as the absorption spectra of dyes.

  15. Improved efficiency in OLEDs with a thin Alq3 interlayer

    International Nuclear Information System (INIS)

    Lian Jiarong; Yuan Yongbo; Cao Lingfang; Zhang Jie; Pang Hongqi; Zhou Yunfei; Zhou Xiang

    2007-01-01

    We demonstrate an improved efficiency in OLEDs with a thin Alq 3 interlayer, which is inserted into the hole-transport layer for adjusting the hole-injection and transport, and improving the hole-electron balance. The thin Alq 3 interlayer can effectively influence the electrical performance and electroluminescence (EL) efficiency of the devices. The devices with an optimum Alq 3 interlayer exhibit a maximum EL efficiency of around 3.3 cd/A, which is improved by a factor of two over the conventional devices (1.6 cd/A) without the interlayer

  16. Advanced light emitting device structures for optoelectronic applications

    International Nuclear Information System (INIS)

    Kovac, J.

    2002-01-01

    Several factors are driving the recent development of light emitting devices (LED,s). The most important ones are brightness, available efficiency, architecture form flexibility, rugged construction and low applied voltages. These are contributing to growth in markets such as traffic lights, automotive brake signals and instrument displays, video displays, traffic signals, decorative signs and the many uses of the new white LED-based products. A new developments are directed to various materials used for high brightness HB-LED,s based on AlGaAs (red), AlInGaP (yellow-green to red) and InGaN (blue, green and white) devices. The development of LED,s depends on epitaxial growth advances, mainly molecular beam epitaxy (MBE) and metalorganic vapor phase epitaxy (MOVPE). As a technology improved, the performace of visible LED,s increased at the rate 10x per decade from less than 0.1 lm/W to the best red and orange LED,s now providing about 100 lm/W. The main engineering challenge is now the extraction or the ability to get all the light out of the chip to where it is needed. This has led to novel changes in the shape of the LED chip and to the replacement of GaAs with transparent GaP substrate throught wafer bonding after the LED has been produced. Most of the focus for nitride devices (InGaN) is to develop improved or new substrate materials to replace sapphire and enable the growth of lower defect density materials. Organic LED,s (OLED,s) have been undergone dramatic improvements in performace in the last five years. Two main technologies for OLED,s have emerged in the last decade, either based on conjaguated polymers, or sublimed films of small molecules. Recent improvements have taken OLED,s to luminous efficiency greater than 20 lm/W. However, in contrast to conventional LED,s, OLED,s share many of the properties associated with other organic substances and polymers. They allow more design flexibility than inorganic LED,s and thus lead to the high

  17. OVPD-processed OLED for general lighting

    OpenAIRE

    Bösing, Manuel

    2012-01-01

    Due to continuous advancements of materials for organic light emitting diodes (OLED) a new field of application currently opens up for OLED technology: General lighting. A significant reduction of OLED production cost might be achieved by employing organic vapor phase deposition (OVPD). OVPD is a novel process for depositing organic thin films from the gas phase. In contrast to the well established process of vacuum thermal evaporation (VTE), OVPD allows to achieve much higher deposition rate...

  18. Voltage-controlled colour-tunable microcavity OLEDs with enhanced colour purity

    International Nuclear Information System (INIS)

    Choy, Wallace C H; Niu, J H; Li, W L; Chui, P C

    2008-01-01

    The emission spectrum of single-unit voltage-controlled colour-tunable organic light emitting devices (OLEDs) has been theoretically and experimentally studied. Our results show that by introducing the microcavity structure, the colour purity of not only the destination colour but also the colour-tunable route can be enhanced, while colour purity is still an issue in typical single-unit voltage-controlled colour-tunable OLEDs. With the consideration of the periodical cycling of resonant wavelength and absorption loss of the metal electrodes, the appropriate change in the thickness of the microcavity structure has been utilized to achieve voltage-controlled red-to-green and red-to-blue colour-tunable OLEDs without adding dyes or other organic materials to the OLEDs

  19. Sharing Data between Mobile Devices, Connected Vehicles and Infrastructure Task 4 / Task 10 : System Architecture and Design Document (SA/DD).

    Science.gov (United States)

    2017-10-27

    This report describes the system architecture and design of the Experimental Prototype System (EPS) for the demonstration of the use of mobile devices in a connected vehicle environment. Specifically, it defines the system structure and behavior, the...

  20. High efficiency and stable white OLED using a single emitter

    Energy Technology Data Exchange (ETDEWEB)

    Li, Jian [Arizona State Univ., Tempe, AZ (United States). School of Mechanical, Aerospace, Chemical and Materials Engineering

    2016-01-18

    The ultimate objective of this project was to demonstrate an efficient and stable white OLED using a single emitter on a planar glass substrate. The focus of the project is on the development of efficient and stable square planar phosphorescent emitters and evaluation of such class of materials in the device settings. Key challenges included improving the emission efficiency of molecular dopants and excimers, controlling emission color of emitters and their excimers, and improving optical and electrical stability of emissive dopants. At the end of this research program, the PI has made enough progress to demonstrate the potential of excimer-based white OLED as a cost-effective solution for WOLED panel in the solid state lighting applications.

  1. Crystal growth of hexaferrite architecture for magnetoelectrically tunable microwave semiconductor integrated devices

    Science.gov (United States)

    Hu, Bolin

    Hexaferrites (i.e., hexagonal ferrites), discovered in 1950s, exist as any one of six crystallographic structural variants (i.e., M-, X-, Y-, W-, U-, and Z-type). Over the past six decades, the hexaferrites have received much attention owing to their important properties that lend use as permanent magnets, magnetic data storage materials, as well as components in electrical devices, particularly those operating at RF frequencies. Moreover, there has been increasing interest in hexaferrites for new fundamental and emerging applications. Among those, electronic components for mobile and wireless communications especially incorporated with semiconductor integrated circuits at microwave frequencies, electromagnetic wave absorbers for electromagnetic compatibility, random-access memory (RAM) and low observable technology, and as composite materials having low dimensions. However, of particular interest is the magnetoelectric (ME) effect discovered recently in the hexaferrites such as SrScxFe12-xO19 (SrScM), Ba2--xSrxZn 2Fe12O22 (Zn2Y), Sr4Co2Fe 36O60 (Co2U) and Sr3Co2Fe 24O41 (Co2Z), demonstrating ferroelectricity induced by the complex internal alignment of magnetic moments. Further, both Co 2Z and Co2U have revealed observable magnetoelectric effects at room temperature, representing a step toward practical applications using the ME effect. These materials hold great potential for applications, since strong magnetoelectric coupling allows switching of the FE polarization with a magnetic field (H) and vice versa. These features could lead to a new type of storage devices, such as an electric field-controlled magnetic memory. A nanoscale-driven crystal growth of magnetic hexaferrites was successfully demonstrated at low growth temperatures (25--40% lower than the temperatures required often for crystal growth). This outcome exhibits thermodynamic processes of crystal growth, allowing ease in fabrication of advanced multifunctional materials. Most importantly, the

  2. Ole Rømers mange talenter

    DEFF Research Database (Denmark)

    Pedersen, Kurt Møller

    2005-01-01

    Artiklen giver en oversigt over Ole Rømers videnskabelige liv som astronom, fysiker og matematiker samt hans betydning som kongelig embedsmand.......Artiklen giver en oversigt over Ole Rømers videnskabelige liv som astronom, fysiker og matematiker samt hans betydning som kongelig embedsmand....

  3. Organic Light-Emitting Diodes (OLEDs) and Optically-Detected Magnetic Resonance (ODMR) studies on organic materials

    Energy Technology Data Exchange (ETDEWEB)

    Cai, Min [Iowa State Univ., Ames, IA (United States)

    2011-01-01

    Organic semiconductors have evolved rapidly over the last decades and currently are considered as the next-generation technology for many applications, such as organic light-emitting diodes (OLEDs) in flat-panel displays (FPDs) and solid state lighting (SSL), and organic solar cells (OSCs) in clean renewable energy. This dissertation focuses mainly on OLEDs. Although the commercialization of the OLED technology in FPDs is growing and appears to be just around the corner for SSL, there are still several key issues that need to be addressed: (1) the cost of OLEDs is very high, largely due to the costly current manufacturing process; (2) the efficiency of OLEDs needs to be improved. This is vital to the success of OLEDs in the FPD and SSL industries; (3) the lifetime of OLEDs, especially blue OLEDs, is the biggest technical challenge. All these issues raise the demand for new organic materials, new device structures, and continued lower-cost fabrication methods. In an attempt to address these issues, we used solution-processing methods to fabricate highly efficient small molecule OLEDs (SMOLEDs); this approach is costeffective in comparison to the more common thermal vacuum evaporation. We also successfully made efficient indium tin oxide (ITO)-free SMOLEDs to further improve the efficiency of the OLEDs. We employed the spin-dependent optically-detected magnetic resonance (ODMR) technique to study the luminescence quenching processes in OLEDs and organic materials in order to understand the intrinsic degradation mechanisms. We also fabricated polymer LEDs (PLEDs) based on a new electron-accepting blue-emitting polymer and studied the effect of molecular weight on the efficiency of PLEDs. All these studies helped us to better understand the underlying relationship between the organic semiconductor materials and the OLEDs’ performance, and will subsequently assist in further enhancing the efficiency of OLEDs. With strongly improved device performance (in addition to

  4. Design of a Simple and Modular 2-DOF Ankle Physiotherapy Device Relying on a Hybrid Serial-Parallel Robotic Architecture

    Directory of Open Access Journals (Sweden)

    Christos E. Syrseloudis

    2011-01-01

    Full Text Available The aim of this work is to propose a new 2-DOF robotic platform with hybrid parallel-serial structure and to undertake its parametric design so that it can follow the whole range of ankle related foot movements. This robot can serve as a human ankle rehabilitation device. The existing ankle rehabilitation devices present typically one or more of the following shortcomings: redundancy, large size, or high cost, hence the need for a device that could offer simplicity, modularity, and low cost of construction and maintenance. In addition, our targeted device must be safe during operation, disallow undesirable movements of the foot, while adaptable to any human foot. Our detailed study of foot kinematics has led us to a new hybrid architecture, which strikes a balance among all aforementioned goals. It consists of a passive serial kinematics chain with two adjustable screws so that the axes of the chain match the two main ankle-axes of typical feet. An active parallel chain, which consists of two prismatic actuators, provides the movement of the platform. Thus, the platform can follow the foot movements, thanks to the passive chain, and also possesses the advantages of parallel robots, including rigidity, high stiffness and force capabilities. The lack of redundancy yields a simpler device with lower size and cost. The paper describes the kinematics modelling of the platform and analyses the force and velocity transmission. The parametric design of the platform is carried out; our simulations confirm the platform's suitability for ankle rehabilitation.

  5. PRISMA-MAR: An Architecture Model for Data Visualization in Augmented Reality Mobile Devices

    Science.gov (United States)

    Gomes Costa, Mauro Alexandre Folha; Serique Meiguins, Bianchi; Carneiro, Nikolas S.; Gonçalves Meiguins, Aruanda Simões

    2013-01-01

    This paper proposes an extension to mobile augmented reality (MAR) environments--the addition of data charts to the more usual text, image and video components. To this purpose, we have designed a client-server architecture including the main necessary modules and services to provide an Information Visualization MAR experience. The server side…

  6. Improving Device Efficiencies in Organic Photovoltaics through the Manipulation of Device Architectures and the Development of Low-Bandgap Materials

    Science.gov (United States)

    Rice, Andrew Hideo

    Over the past two decades, vast amounts of research have been conducted in the pursuit of suitable organic semiconductors to replace inorganic materials in electronic applications due to their advantages of being lightweight, flexible, and solution-processible. However, before organic photovoltaics (OPVs) can be truly competitive and commercially viable, their efficiencies must be improved significantly. In this examination, we pursue higher efficiency OPVs in two different ways. Our attempts focus on 1) altering the microstructure of devices to improve charge dissociation, charge transport, and our understanding of how these devices function, and 2) tailoring materials to achieve optimal band gaps and energy levels for use in organic electronics. First, we demonstrate how the vertical morphology of bulk heterojunction (BHJ) solar cells, with an active layer consisting of self-assembled poly(3-hexylthiophene) (P3HT) nanowires and (6,6)-phenyl C61-butyric acid methyl ester (PCBM), can be beneficially influenced. Most device fabrication routes using similar materials employ an annealing step to influence active layer morphology, but this process can create an unfavorable phase migration where P3HT is driven toward the cathode. In contrast, we demonstrate devices that exhibit an increase in relative fullerene concentration at the top of the active layer by introducing the donor phase as a solid nanowire in the active layer solution and altering the pre-spin drying time. X-ray photoelectron spectroscopy (XPS) and conductive and photoconductive atomic force microscopy (cAFM and pcAFM) provide detailed information about how the surface of the active layer can be influenced; this is done by tracking the concentration and alignment of P3HT and PCBM domains. Using this new procedure, devices are made with power conversion efficiencies surpassing 2%. Additionally, we show that nanowires grown in the presence of the fullerene perform differently than those that are grown and

  7. Transfer mechanisms between emitter molecules for OLED applications

    Energy Technology Data Exchange (ETDEWEB)

    Steinbacher, Frank [Department of Materials Science VI, University of Erlangen-Nuernberg (Germany); Siemens AG, CT MM 1, Erlangen (Germany); Chiu, Chien-Shu [Department of Electrical Engineering and Information Technology, Technical University of Braunschweig (Germany); Siemens AG, CT MM 1, Erlangen (Germany); Krause, Ralf; Hunze, Arvid [Siemens AG, CT MM 1, Erlangen (Germany); Winnacker, Albrecht [Department of Materials Science VI, University of Erlangen-Nuernberg (Germany)

    2009-07-01

    Within the last few years white organic light emitting diodes based on small molecules have shown the potential to have a promising future in the field of lighting technology. Nevertheless there is still room for improvement of the overall efficiency and lifetime of white OLEDs. A deeper understanding of the energy transfer mechanisms between different matrix and emitter molecules used in the OLED stack concept can help to optimize the layout and reduce driving voltage thus increasing the power efficiency and color stability of the device. To simplify the complex interactions within a complete white OLED we start out with a basic model system only containing the molecules of interest. This enables us to predict the fundamental concepts causing the behavior of more intricate systems. Using photoluminescence, excitation spectra and time-resolved photoluminescence we investigated the exciton transfer between different dyes for a variety of emitter systems. Our results indicate a dependence of exciton transfer probability on the total concentrations and therefore the distance between the molecules involved.

  8. Development of robust flexible OLED encapsulations using simulated estimations and experimental validations

    International Nuclear Information System (INIS)

    Lee, Chang-Chun; Shih, Yan-Shin; Wu, Chih-Sheng; Tsai, Chia-Hao; Yeh, Shu-Tang; Peng, Yi-Hao; Chen, Kuang-Jung

    2012-01-01

    This work analyses the overall stress/strain characteristic of flexible encapsulations with organic light-emitting diode (OLED) devices. A robust methodology composed of a mechanical model of multi-thin film under bending loads and related stress simulations based on nonlinear finite element analysis (FEA) is proposed, and validated to be more reliable compared with related experimental data. With various geometrical combinations of cover plate, stacked thin films and plastic substrate, the position of the neutral axis (NA) plate, which is regarded as a key design parameter to minimize stress impact for the concerned OLED devices, is acquired using the present methodology. The results point out that both the thickness and mechanical properties of the cover plate help in determining the NA location. In addition, several concave and convex radii are applied to examine the reliable mechanical tolerance and to provide an insight into the estimated reliability of foldable OLED encapsulations. (paper)

  9. High Quantum Efficiency OLED Lighting Systems

    Energy Technology Data Exchange (ETDEWEB)

    Shiang, Joseph [General Electric (GE) Global Research, Fairfield, CT (United States)

    2011-09-30

    The overall goal of the program was to apply improvements in light outcoupling technology to a practical large area plastic luminaire, and thus enable the product vision of an extremely thin form factor high efficiency large area light source. The target substrate was plastic and the baseline device was operating at 35 LPW at the start of the program. The target LPW of the program was a >2x improvement in the LPW efficacy and the overall amount of light to be delivered was relatively high 900 lumens. Despite the extremely difficult challenges associated with scaling up a wet solution process on plastic substrates, the program was able to make substantial progress. A small molecule wet solution process was successfully implemented on plastic substrates with almost no loss in efficiency in transitioning from the laboratory scale glass to large area plastic substrates. By transitioning to a small molecule based process, the LPW entitlement increased from 35 LPW to 60 LPW. A further 10% improvement in outcoupling efficiency was demonstrated via the use of a highly reflecting cathode, which reduced absorptive loss in the OLED device. The calculated potential improvement in some cases is even larger, ~30%, and thus there is considerable room for optimism in improving the net light coupling efficacy, provided absorptive loss mechanisms are eliminated. Further improvements are possible if scattering schemes such as the silver nanowire based hard coat structure are fully developed. The wet coating processes were successfully scaled to large area plastic substrate and resulted in the construction of a 900 lumens luminaire device.

  10. Parametric Approach to Assessing Performance of High-Lift Device Active Flow Control Architectures

    Directory of Open Access Journals (Sweden)

    Yu Cai

    2017-02-01

    Full Text Available Active Flow Control is at present an area of considerable research, with multiple potential aircraft applications. While the majority of research has focused on the performance of the actuators themselves, a system-level perspective is necessary to assess the viability of proposed solutions. This paper demonstrates such an approach, in which major system components are sized based on system flow and redundancy considerations, with the impacts linked directly to the mission performance of the aircraft. Considering the case of a large twin-aisle aircraft, four distinct active flow control architectures that facilitate the simplification of the high-lift mechanism are investigated using the demonstrated approach. The analysis indicates a very strong influence of system total mass flow requirement on architecture performance, both for a typical mission and also over the entire payload-range envelope of the aircraft.

  11. Narrow Bandwidth Top-Emitting OLEDs Designed for Rhodamine 6G Excitation in Biological Sensing Applications

    Directory of Open Access Journals (Sweden)

    Matthias Jahnel

    2015-11-01

    Full Text Available Organic light emitting diodes (OLED are promising candidates offering in optical sensor applications to detect different gas compositions and excitable optical marker groups in chemical and biological processes. They enable attractive solutions for monitoring the gas phase composition of e.g., dissolved molecular oxygen (O2 species in bio reactors or excitation of fluorescent markers. In this work, we investigate different OLED devices for biomedical applications to excite the fluorescent dye rhodamine 6G (R6G. The OLED devices are built in top emission geometry comprising a distributed Bragg reflector (DBR acting as optical mirror. The OLED is optimized to provide a very narrow emission characteristic to excite the R6G at 530 nm wavelength and enabling the possibility to minimize the optical crosstalk between the OLED electroluminescence and the fluorescence of R6G. The DBR includes a thin film encapsulation and enables the narrowing of the spectral emission band depending on the number of DBR pairs. The comparison between optical simulation data and experimental results exhibits good agreement and proves process stability.

  12. Mixed-ligand Al complex-a new approach for more high efficient OLEDs

    Energy Technology Data Exchange (ETDEWEB)

    Petrova, Petia K., E-mail: petia@clf.bas.bg [Institute of Optical Materials and Technologies ' Acad. J. Malinowski' , Bulgarian Academy of Sciences, Acad. G Bonchev st., bl. 109, 1113 Sofia (Bulgaria); Tomova, Reni L.; Stoycheva-Topalova, Rumiana T. [Institute of Optical Materials and Technologies ' Acad. J. Malinowski' , Bulgarian Academy of Sciences, Acad. G Bonchev st., bl. 109, 1113 Sofia (Bulgaria); Kaloyanova, Stefka S.; Deligeorgiev, Todor G. [Applied Organic Chemistry, Faculty of Chemistry, University of Sofia, Sofia 1164 (Bulgaria)

    2012-02-15

    The mixed-ligand Aluminum bis(8-hydroxyquinoline) acetylacetonate (Alq{sub 2}Acac) complex was presented and its performance as electroluminescent and electron transporting layer for OLED was studied. The photophysical properties of the novel complex were investigated and compared with the properties of the parent Alq{sub 3}. Highly efficient OLED based on the mixed-ligand Al complex was developed with two times higher luminescence and efficiency compared to the identical OLED based on the conventional Alq{sub 3} The better performance of the devices make the novel Al complex a very promising material for OLEDs. - Highlights: Black-Right-Pointing-Pointer A novel electroluminescent Alq{sub 2}Acac complex is presented as material for OLED. Black-Right-Pointing-Pointer Electroluminescent emission of Alq{sub 2}Acac is very similar to that of commercial Alq{sub 3}. Black-Right-Pointing-Pointer Devices with Alq{sub 2}Acac show better characteristics compared to those with Alq{sub 3}.

  13. Fog Computing and Edge Computing Architectures for Processing Data From Diabetes Devices Connected to the Medical Internet of Things.

    Science.gov (United States)

    Klonoff, David C

    2017-07-01

    The Internet of Things (IoT) is generating an immense volume of data. With cloud computing, medical sensor and actuator data can be stored and analyzed remotely by distributed servers. The results can then be delivered via the Internet. The number of devices in IoT includes such wireless diabetes devices as blood glucose monitors, continuous glucose monitors, insulin pens, insulin pumps, and closed-loop systems. The cloud model for data storage and analysis is increasingly unable to process the data avalanche, and processing is being pushed out to the edge of the network closer to where the data-generating devices are. Fog computing and edge computing are two architectures for data handling that can offload data from the cloud, process it nearby the patient, and transmit information machine-to-machine or machine-to-human in milliseconds or seconds. Sensor data can be processed near the sensing and actuating devices with fog computing (with local nodes) and with edge computing (within the sensing devices). Compared to cloud computing, fog computing and edge computing offer five advantages: (1) greater data transmission speed, (2) less dependence on limited bandwidths, (3) greater privacy and security, (4) greater control over data generated in foreign countries where laws may limit use or permit unwanted governmental access, and (5) lower costs because more sensor-derived data are used locally and less data are transmitted remotely. Connected diabetes devices almost all use fog computing or edge computing because diabetes patients require a very rapid response to sensor input and cannot tolerate delays for cloud computing.

  14. High Performance OLED Panel and Luminaire

    Energy Technology Data Exchange (ETDEWEB)

    Spindler, Jeffrey [OLEDWorks LLC, Rochester, NY (United States)

    2017-02-20

    In this project, OLEDWorks developed and demonstrated the technology required to produce OLED lighting panels with high energy efficiency and excellent light quality. OLED panels developed in this program produce high quality warm white light with CRI greater than 85 and efficacy up to 80 lumens per watt (LPW). An OLED luminaire employing 24 of the high performance panels produces practical levels of illumination for general lighting, with a flux of over 2200 lumens at 60 LPW. This is a significant advance in the state of the art for OLED solid-state lighting (SSL), which is expected to be a complementary light source to the more advanced LED SSL technology that is rapidly replacing all other traditional forms of lighting.

  15. Improvements of phosphorescent white OLEDs performance for lighting application.

    Science.gov (United States)

    Lee, Jonghee; Chu, Hye Yong; Lee, Jeong-Ik; Song, Ki-Im; Lee, Su Jin

    2008-10-01

    We developed white OLED device with high power efficiency, in which blue and orange phosphorescent emitters were used. By introduction of multi-functional interlayer which has partial doping of orange dopant inside EBL, we report WOLEDs with peak external efficiencies up to (14.1% EQE, 31.3 Im/W) without light out-coupling technique. At 1000 cd/m2, the performance achieved was 11.9% EQE, 18.7 Im/W with CIE = (0.39, 0.44). We also found that WOLED performances are related with doping ratio of the orange dopant that was inserted inside EBL.

  16. CALiPER Report 24: OLED Luminaires

    Energy Technology Data Exchange (ETDEWEB)

    Miller, N. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Leon, F. A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Davis, J. L. [RTI International, Research Triangle Park, NC (United States)

    2017-08-01

    This report documents an initial investigation of OLED luminaires and summarizes the key features of those products. In addition to photometric testing of four commercial products in independent laboratories, PNNL examined many of the products through teardown testing (disassemblies to identify parts and functionality) in PNNL laboratories. Results of these tests as well as results of stress testing of several OLED luminaires at RTI International have been included.

  17. Nanoscale architectural tuning of parylene patch devices to control therapeutic release rates

    International Nuclear Information System (INIS)

    Pierstorff, Erik; Lam, Robert; Ho, Dean

    2008-01-01

    The advent of therapeutic functionalized implant coatings has significantly impacted the medical device field by enabling prolonged device functionality for enhanced patient treatment. Incorporation of drug release from a stable, biocompatible surface is instrumental in decreasing systemic application of toxic therapeutics and increasing the lifespan of implants by the incorporation of antibiotics and anti-inflammatories. In this study, we have developed a parylene C-based device for controlled release of Doxorubicin, an anti-cancer chemotherapy and definitive read-out for preserved drug functionality, and further characterized the parylene deposition condition-dependent tunability of drug release. Drug release is controlled by the deposition of a layer of 20-200 nm thick parylene over the drug layer. This places a porous layer above the Doxorubicin, limiting drug elution based on drug accessibility to solvent and the solvent used. An increase in the thickness of the porous top layer prolongs the elution of active drug from the device from, in the conditions tested, the order of 10 min to the order of 2 d in water and from the order of 10 min to no elution in PBS. Thus, the controlled release of an anti-cancer therapeutic has been achieved via scalably fabricated, parylene C-encapsulated drug delivery devices.

  18. High-efficiency white OLEDs based on small molecules

    Science.gov (United States)

    Hatwar, Tukaram K.; Spindler, Jeffrey P.; Ricks, M. L.; Young, Ralph H.; Hamada, Yuuhiko; Saito, N.; Mameno, Kazunobu; Nishikawa, Ryuji; Takahashi, Hisakazu; Rajeswaran, G.

    2004-02-01

    Eastman Kodak Company and SANYO Electric Co., Ltd. recently demonstrated a 15" full-color, organic light-emitting diode display (OLED) using a high-efficiency white emitter combined with a color-filter array. Although useful for display applications, white emission from organic structures is also under consideration for other applications, such as solid-state lighting, where high efficiency and good color rendition are important. By incorporating adjacent blue and orange emitting layers in a multi-layer structure, highly efficient, stable white emission has been attained. With suitable host and dopant combinations, a luminance yield of 20 cd/A and efficiency of 8 lm/W have been achieved at a drive voltage of less than 8 volts and luminance level of 1000 cd/m2. The estimated external efficiency of this device is 6.3% and a high level of operational stability is observed. To our knowledge, this is the highest performance reported so far for white organic electroluminescent devices. We will review white OLED technology and discuss the fabrication and operating characteristics of these devices.

  19. Innovative architecture of switching device for expanding the applications in fiber to the home (FTTH)

    Science.gov (United States)

    Mahmoud, Mohamed; Fayed, Heba A.; Aly, Moustafa H.; Aboul Seoud, A. K.

    2011-08-01

    A new device, optical cross add drop multiplexer (OXADM), is proposed and analyzed. It uses the combination concept of optical add drop multiplexer (OADM) and optical cross connect (OXC). It enables a wavelength switch while implementing add and drop functions simultaneously. So, it expands the applications in fiber to the home (FTTH) and optical core networks. A very high isolation crosstalk level (~ 60 dB) is achieved. Also, a bidirectional OXADM and N×N OXADM are proposed. Finally, a multistage OXADM is presented making some sort of wavelength buffering. To make these devices operate more efficient, tunable fiber Bragg gratings (TFBGs) switches are used to control the operation mechanism.

  20. Creation of a U.S. Phosphorescent OLED Lighting Panel Manufacturing Facility

    Energy Technology Data Exchange (ETDEWEB)

    Hack, Michael

    2013-09-30

    Universal Display Corporation (UDC) has pioneered high efficacy phosphorescent OLED (PHOLED™) technology to enable the realization of an exciting new form of high quality, energy saving solid-date lighting. In laboratory test devices, we have demonstrated greater than 100 lm/W conversion efficacy. In this program, Universal Display will demonstrate the scalability of its proprietary UniversalPHOLED technology and materials for the manufacture of white OLED lighting panels that meet commercial lighting targets. Moser Baer Technologies will design and build a U.S.- based pilot facility. The objective of this project is to establish a pilot phosphorescent OLED (PHOLED) manufacturing line in the U.S. Our goal is that at the end of the project, prototype lighting panels could be provided to U.S. luminaire manufacturers for incorporation into products to facilitate the testing of design concepts and to gauge customer acceptance, so as to facilitate the growth of the embryonic U.S. OLED lighting industry. In addition, the team will provide a cost of ownership analysis to quantify production costs including OLED performance metrics which relate to OLED cost such as yield, materials usage, cycle time, substrate area, and capital depreciation. This project was part of a new DOE initiative designed to help establish and maintain U.S. leadership in this program will support key DOE objectives by showing a path to meet Department of Energy Solid-State Lighting Manufacturing Roadmap cost targets, as well as meeting its efficiency targets by demonstrating the energy saving potential of our technology through the realization of greater than 76 lm/W OLED lighting panels by 2012.

  1. Architecture and prototype of human-machine interface with mobile robotic device

    International Nuclear Information System (INIS)

    Dyumin, A.A.; Sorokoumov, P.S.; Chepin, E.V.; Urvanov, G.A.

    2013-01-01

    The possibility of controlling mobile robotic (MRD) device is analyzed and a prototype control system is described. It is established that, for controlling MRD, it is expedient to use a brain-computer interface. A system of interpretation of information obtained from the operator brain has been developed and used in the proposed prototype control system [ru

  2. Enhanced color purity of blue OLEDs based on well-design structure

    Science.gov (United States)

    Du, Qianqian; Wang, Wenjun; Li, Shuhong; Wang, Qingru; Xia, Shuzhen; Zhang, Bingyuan; Wang, Minghong; Fan, Quli

    2016-09-01

    We have fabricated blue organic light-emitting devices (OLEDs) with higher color purity and stability by optimizing the structure of the Glass/ITO/NPB(50 nm)/ BCzVBi (30 nm)/ TPBi (x nm)/Alq3(20 nm)/LiF/Al. The results show that the introducing of hole blocking layer(HBL) TPBi greatly can improve not only the color purity but the color stability, which owe to its higher the Highest Occupied Molecular Orbital (HOMO) energy levels of 6.2 eV. We expect our work will be useful to optimizing the blue OLEDs structure to enhancing the color property.

  3. Synthesis of InSb Nanowire Architectures - Building Blocks for Majorana Devices

    Science.gov (United States)

    Car, Diana

    Breakthroughs in material development are playing a major role in the emerging field of topological quantum computation with Majorana Zero Modes (MZMs). Due to the strong spin-orbit interaction and large Landé g-factor InSb nanowires are one of the most promising one dimensional material systems in which to detect MZMs. The next generation of Majorana experiments should move beyond zero-mode detection and demonstrate the non-Abelian nature of MZMs by braiding. To achieve this goal advanced material platforms are needed: low-disorder, single-crystalline, planar networks of nanowires with high spin-orbit energy. In this talk I will discuss the formation and electronic properties of InSb nanowire networks. The bottom-up synthesis method we have developed is generic and can be employed to synthesize interconnected nanowire architectures of group III-V, II-VI and IV materials as long as they grow along a direction.

  4. A Parallel Implementation of a Smoothed Particle Hydrodynamics Method on Graphics Hardware Using the Compute Unified Device Architecture

    International Nuclear Information System (INIS)

    Wong Unhong; Wong Honcheng; Tang Zesheng

    2010-01-01

    The smoothed particle hydrodynamics (SPH), which is a class of meshfree particle methods (MPMs), has a wide range of applications from micro-scale to macro-scale as well as from discrete systems to continuum systems. Graphics hardware, originally designed for computer graphics, now provide unprecedented computational power for scientific computation. Particle system needs a huge amount of computations in physical simulation. In this paper, an efficient parallel implementation of a SPH method on graphics hardware using the Compute Unified Device Architecture is developed for fluid simulation. Comparing to the corresponding CPU implementation, our experimental results show that the new approach allows significant speedups of fluid simulation through handling huge amount of computations in parallel on graphics hardware.

  5. Acidity-Controlled Conducting Polymer Films for Organic Thermoelectric Devices with Horizontal and Vertical Architectures

    Science.gov (United States)

    Lee, Woongki; Song, Myeonghun; Park, Soohyung; Nam, Sungho; Seo, Jooyeok; Kim, Hwajeong; Kim, Youngkyoo

    2016-09-01

    Organic thermoelectric devices (OTEDs) are recognized one of the next generation energy conversion platforms because of their huge potentials for securing electricity continuously from even tiny heat sources in our daily life. The advantage of OTEDs can be attributable to the design freedom in device shapes and the low-cost fabrication by employing solution coating processes at low temperatures. As one of the major OTE materials to date, poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) has been used, but no study has been yet carried out on its acidity control even though the acidic components in OTEDs can seriously affect the device performance upon operation. Here we demonstrate that the addition of aniline (a weak base) can control the acidity of PEDOT:PSS and enhance the performance of OTEDs. In particular, the vertical OTEDs with aniline-doped PEDOT:PSS films (active area = 1.0 cm2) could continuously generate electricity (0.06 nW) even at low temperatures (<38 °C) when they were mounted on a desk lamp (power = 24 W).

  6. The Architecture of Colloidal Quantum Dot Solar Cells: Materials to Devices

    KAUST Repository

    Kramer, Illan J.

    2014-01-08

    The materials chemistry of Colloidal Quantum Dot (CQDs) suspended in solution and processed into films has provided a foundation onto which useful photovoltaic devices can be built. These active materials offer the benefits of solution processing paired with the flexibility of adjustable bandgaps, tailored to suit a particular need. In parallel with these advances, pursuing device geometries that better leverage the available electronic properties of CQD films has borne fruit in further advancing CQD solar cell performance. For active materials such as CQD films where 1/α, where alpha is the absorption coefficient, is of the same order as the free carrier extraction length, external quantum efficiency (EQE) measurements have proved useful in profiling the effectiveness of each nanometer of device thickness at extracting photogenerated carriers. Because CQD films have the added complications of being made of variable-sized constituent material building blocks as well as being deposited from solution, the nature of charge transport through the films can also be size-dependent and matrix dependent.

  7. Optimization of the host–guest system within an OLED using different models of mobility

    Energy Technology Data Exchange (ETDEWEB)

    Adames Prada, Rosana, E-mail: rdadamesp@unal.edu.co; Ardila Vargas, Angel Miguel, E-mail: amardilav@unal.edu.co

    2014-12-15

    To optimize the host–guest system of organic light emitting devices (OLEDs), it were performed simulations by doping a small molecule organic semiconductor (acting as host) with the transition organometallic complex known as Ir(ppy){sub 2}(acac) (acting as a guest). The simulation was carried out using simOLED with different mobility models: the Pool–Frenkel Model (PFM), the Extended Gaussian Disorder Model (EGDM) and Extended Correlated Disorder Model (ECDM), with the aim to determine the magnitude of some parameters like temperature, applied electric field, film thickness and charge carrier density that improve the electrical and optical properties of OLEDs with a more simplified structure like ITO/CBP/CBP:Ir(ppy){sub 2}(acac)/TPBi/LiF/Al.

  8. Considerable improvement in the stability of solution processed small molecule OLED by annealing

    Energy Technology Data Exchange (ETDEWEB)

    Mao Guilin [Key Laboratory of Photonics Technology for Information, Key Laboratory for Physical Electronics and Devices of the Ministry of Education, School of Electronic and Information Engineering, Xi' an Jiaotong University, Xi' an, 710049 (China); Wu Zhaoxin, E-mail: zhaoxinwu@mail.xjtu.edu.cn [Key Laboratory of Photonics Technology for Information, Key Laboratory for Physical Electronics and Devices of the Ministry of Education, School of Electronic and Information Engineering, Xi' an Jiaotong University, Xi' an, 710049 (China); He Qiang [Key Laboratory of Photonics Technology for Information, Key Laboratory for Physical Electronics and Devices of the Ministry of Education, School of Electronic and Information Engineering, Xi' an Jiaotong University, Xi' an, 710049 (China); Department of UAV, Wuhan Ordnance Noncommissioned Officers Academy, Wuhan, 430075 (China); Jiao Bo; Xu Guojin; Hou Xun [Key Laboratory of Photonics Technology for Information, Key Laboratory for Physical Electronics and Devices of the Ministry of Education, School of Electronic and Information Engineering, Xi' an Jiaotong University, Xi' an, 710049 (China); Chen Zhijian; Gong Qihuang [State Key Laboratory for Mesoscopic Physics and Department of Physics, Peking University, Beijing, 100871 (China)

    2011-06-15

    We investigated the annealing effect on solution processed small organic molecule organic films, which were annealed with various conditions. It was found that the densities of the spin-coated (SC) films increased and the surface roughness decreased as the annealing temperature rose. We fabricated corresponding organic light emitting diodes (OLEDs) by spin coating on the same annealing conditions. The solution processed OLEDs show the considerable efficiency and stability, which were prior or equivalent to the vacuum-deposited (VD) counterparts. Our research shows that annealing process plays a key role in prolonging the lifetime of solution processed small molecule OLEDs, and the mechanism for the improvement of the device performance upon annealing was also discussed.

  9. Light emitting device having peripheral emissive region

    Science.gov (United States)

    Forrest, Stephen R

    2013-05-28

    Light emitting devices are provided that include one or more OLEDs disposed only on a peripheral region of the substrate. An OLED may be disposed only on a peripheral region of a substantially transparent substrate and configured to emit light into the substrate. Another surface of the substrate may be roughened or include other features to outcouple light from the substrate. The edges of the substrate may be beveled and/or reflective. The area of the OLED(s) may be relatively small compared to the substrate surface area through which light is emitted from the device. One or more OLEDs also or alternatively may be disposed on an edge of the substrate about perpendicular to the surface of the substrate through which light is emitted, such that they emit light into the substrate. A mode expanding region may be included between each such OLED and the substrate.

  10. Compact FPGA hardware architecture for public key encryption in embedded devices.

    Science.gov (United States)

    Rodríguez-Flores, Luis; Morales-Sandoval, Miguel; Cumplido, René; Feregrino-Uribe, Claudia; Algredo-Badillo, Ignacio

    2018-01-01

    Security is a crucial requirement in the envisioned applications of the Internet of Things (IoT), where most of the underlying computing platforms are embedded systems with reduced computing capabilities and energy constraints. In this paper we present the design and evaluation of a scalable low-area FPGA hardware architecture that serves as a building block to accelerate the costly operations of exponentiation and multiplication in [Formula: see text], commonly required in security protocols relying on public key encryption, such as in key agreement, authentication and digital signature. The proposed design can process operands of different size using the same datapath, which exhibits a significant reduction in area without loss of efficiency if compared to representative state of the art designs. For example, our design uses 96% less standard logic than a similar design optimized for performance, and 46% less resources than other design optimized for area. Even using fewer area resources, our design still performs better than its embedded software counterparts (190x and 697x).

  11. High-performance field emission device utilizing vertically aligned carbon nanotubes-based pillar architectures

    Science.gov (United States)

    Gupta, Bipin Kumar; Kedawat, Garima; Gangwar, Amit Kumar; Nagpal, Kanika; Kashyap, Pradeep Kumar; Srivastava, Shubhda; Singh, Satbir; Kumar, Pawan; Suryawanshi, Sachin R.; Seo, Deok Min; Tripathi, Prashant; More, Mahendra A.; Srivastava, O. N.; Hahm, Myung Gwan; Late, Dattatray J.

    2018-01-01

    The vertical aligned carbon nanotubes (CNTs)-based pillar architectures were created on laminated silicon oxide/silicon (SiO2/Si) wafer substrate at 775 °C by using water-assisted chemical vapor deposition under low pressure process condition. The lamination was carried out by aluminum (Al, 10.0 nm thickness) as a barrier layer and iron (Fe, 1.5 nm thickness) as a catalyst precursor layer sequentially on a silicon wafer substrate. Scanning electron microscope (SEM) images show that synthesized CNTs are vertically aligned and uniformly distributed with a high density. The CNTs have approximately 2-30 walls with an inner diameter of 3-8 nm. Raman spectrum analysis shows G-band at 1580 cm-1 and D-band at 1340 cm-1. The G-band is higher than D-band, which indicates that CNTs are highly graphitized. The field emission analysis of the CNTs revealed high field emission current density (4mA/cm2 at 1.2V/μm), low turn-on field (0.6 V/μm) and field enhancement factor (6917) with better stability and longer lifetime. Emitter morphology resulting in improved promising field emission performances, which is a crucial factor for the fabrication of pillared shaped vertical aligned CNTs bundles as practical electron sources.

  12. High-performance field emission device utilizing vertically aligned carbon nanotubes-based pillar architectures

    Directory of Open Access Journals (Sweden)

    Bipin Kumar Gupta

    2018-01-01

    Full Text Available The vertical aligned carbon nanotubes (CNTs-based pillar architectures were created on laminated silicon oxide/silicon (SiO2/Si wafer substrate at 775 °C by using water-assisted chemical vapor deposition under low pressure process condition. The lamination was carried out by aluminum (Al, 10.0 nm thickness as a barrier layer and iron (Fe, 1.5 nm thickness as a catalyst precursor layer sequentially on a silicon wafer substrate. Scanning electron microscope (SEM images show that synthesized CNTs are vertically aligned and uniformly distributed with a high density. The CNTs have approximately 2–30 walls with an inner diameter of 3–8 nm. Raman spectrum analysis shows G-band at 1580 cm−1 and D-band at 1340 cm−1. The G-band is higher than D-band, which indicates that CNTs are highly graphitized. The field emission analysis of the CNTs revealed high field emission current density (4mA/cm2 at 1.2V/μm, low turn-on field (0.6 V/μm and field enhancement factor (6917 with better stability and longer lifetime. Emitter morphology resulting in improved promising field emission performances, which is a crucial factor for the fabrication of pillared shaped vertical aligned CNTs bundles as practical electron sources.

  13. Emotion devices. Tje role of concrete frame structures in the architecture of Kazuo Shinohara

    OpenAIRE

    Massip-Bosch, Enric

    2016-01-01

    [EN] The work of the architect Kazuo Shinohara had as main goal the creation of emotion in the center of the house. His work, although mostly consisting of few, rather small single-family houses, places him as the most influential of his generation in Japan today.In his designs of the mid-1970s he uses concrete frame structures as a fundamental device to question the foundations of domesticity. By contrasting scales and textures, and the geometry and dimension of support elements, achieves a ...

  14. Spectrally narrowed leaky waveguide edge emission and transient electrluminescent dynamics of OLEDs

    International Nuclear Information System (INIS)

    Zhengqing, Gan

    2010-01-01

    In summary, there are two major research works presented in this dissertation. The first research project (Chapter 4) is spectrally narrowed edge emission from Organic Light Emitting Diodes. The second project (Chapter 5) is about transient electroluminescent dynamics in OLEDs. Chapter 1 is a general introduction of OLEDs. Chapter 2 is a general introduction of organic semiconductor lasers. Chapter 3 is a description of the thermal evaporation method for OLED fabrication. The detail of the first project was presented in Chapter 4. Extremely narrowed spectrum was observed from the edge of OLED devices. A threshold thickness exists, above which the spectrum is narrow, and below which the spectrum is broad. The FWHM of spectrum depends on the material of the organic thin films, the thickness of the organic layers, and length of the OLED device. A superlinear relationship between the output intensity of the edge emission and the length of the device was observed, which is probably due to the misalignment of the device edge and the optical fiber detector. The original motivation of this research is for organic semiconductor laser that hasn't been realized due to the extremely high photon absorption in OLED devices. Although we didn't succeed in fabricating an electrically pumped organic laser diode, we made a comprehensive research in edge emission of OLEDs which provides valuable results in understanding light distribution and propagation in OLED devices. Chapter 5 focuses on the second project. A strong spike was observed at the falling edge of a pulse, and a long tail followed. The spike was due to the recombination of correlated charge pair (CCP) created by trapped carriers in guest molecules of the recombination zone. When the bias was turned off, along with the decreasing of electric field in the device, the electric field induced quenching decreases and the recombination rate of the CCP increases which result in the spike. This research project provides a

  15. Spectrally narrowed leaky waveguide edge emission and transient electrluminescent dynamics of OLEDs

    Energy Technology Data Exchange (ETDEWEB)

    Zhengqing, Gan [Iowa State Univ., Ames, IA (United States)

    2010-01-01

    In summary, there are two major research works presented in this dissertation. The first research project (Chapter 4) is spectrally narrowed edge emission from Organic Light Emitting Diodes. The second project (Chapter 5) is about transient electroluminescent dynamics in OLEDs. Chapter 1 is a general introduction of OLEDs. Chapter 2 is a general introduction of organic semiconductor lasers. Chapter 3 is a description of the thermal evaporation method for OLED fabrication. The detail of the first project was presented in Chapter 4. Extremely narrowed spectrum was observed from the edge of OLED devices. A threshold thickness exists, above which the spectrum is narrow, and below which the spectrum is broad. The FWHM of spectrum depends on the material of the organic thin films, the thickness of the organic layers, and length of the OLED device. A superlinear relationship between the output intensity of the edge emission and the length of the device was observed, which is probably due to the misalignment of the device edge and the optical fiber detector. The original motivation of this research is for organic semiconductor laser that hasn't been realized due to the extremely high photon absorption in OLED devices. Although we didn't succeed in fabricating an electrically pumped organic laser diode, we made a comprehensive research in edge emission of OLEDs which provides valuable results in understanding light distribution and propagation in OLED devices. Chapter 5 focuses on the second project. A strong spike was observed at the falling edge of a pulse, and a long tail followed. The spike was due to the recombination of correlated charge pair (CCP) created by trapped carriers in guest molecules of the recombination zone. When the bias was turned off, along with the decreasing of electric field in the device, the electric field induced quenching decreases and the recombination rate of the CCP increases which result in the spike. This research project provides

  16. Stacked white OLED having separate red, green and blue sub-elements

    Energy Technology Data Exchange (ETDEWEB)

    Forrest, Stephen; Qi, Xiangfei; Slootsky, Michael

    2014-07-01

    The present invention relates to efficient organic light emitting devices (OLEDs). The devices employ three emissive sub-elements, typically emitting red, green and blue, to sufficiently cover the visible spectrum. Thus, the devices may be white-emitting OLEDs, or WOLEDs. Each sub-element comprises at least one organic layer which is an emissive layer--i.e., the layer is capable of emitting light when a voltage is applied across the stacked device. The sub-elements are vertically stacked and are separated by charge generating layers. The charge-generating layers are layers that inject charge carriers into the adjacent layer(s) but do not have a direct external connection.

  17. An Architecture Approach for 3D Render Distribution using Mobile Devices in Real Time

    Directory of Open Access Journals (Sweden)

    Holman Bolivar-Baron

    2015-06-01

    Full Text Available Nowadays, video games such as Massively Multiplayer Online Game (MMOG have become cultural mediators. Mobile games contribute to a large number of downloads and potential benefits in the applications market. Although processing power of mobile devices increases the bandwidth transmission, a poor network connectivity may bottleneck Gaming as a Service (GaaS. In order to enhance performance in digital ecosystem, processing tasks are distributed among thin client devices and robust servers. This research is based on the method ‘divide and rule’, that is, volumetric surfaces are subdivided using a tree-KD of sequence of scenes in a game, so reducing the surface into small sets of points. Reconstruction efficiency is improved, because the search of data is performed in local and small regions. Processes are modeled through a finite set of states that are built using Hidden Markov Models with domains configured by heuristics. Six test that control the states of each heuristic, including the number of intervals are carried out to validate the proposed model. This validation concludes that the proposed model optimizes response frames per second, in a sequence of interactions.

  18. Organic light emitting device architecture for reducing the number of organic materials

    Science.gov (United States)

    D'Andrade, Brian [Westampton, NJ; Esler, James [Levittown, PA

    2011-10-18

    An organic light emitting device is provided. The device includes an anode and a cathode. A first emissive layer is disposed between the anode and the cathode. The first emissive layer includes a first non-emitting organic material, which is an organometallic material present in the first emissive layer in a concentration of at least 50 wt %. The first emissive layer also includes a first emitting organic material. A second emissive layer is disposed between the first emissive layer and the cathode, preferably, in direct contact with the first emissive layer. The second emissive material includes a second non-emitting organic material and a second emitting organic material. The first and second non-emitting materials, and the first and second emitting materials, are all different materials. A first non-emissive layer is disposed between the first emissive layer and the anode, and in direct contact with the first emissive layer. The first non- emissive layer comprises the first non-emissive organic material.

  19. P1-7: Modern Display Technology in Vision Science: Assessment of OLED and LCD Monitors for Visual Experiments

    Directory of Open Access Journals (Sweden)

    Tobias Elze

    2012-10-01

    Full Text Available For many decades, cathode ray tube (CRT monitors have been the dominant display technology in vision science. However, in recent years, most manufacturers stopped their CRT production lines, which enforces the application of alternative display technology in the field of vision science. Here, we analyze liquid crystal displays (LCDs and organic light-emitting diode (OLED monitors for their applicability in vision science experiments. Based on extensive measurements of their photometric output, we compare these technologies and contrast them with classical CRT monitors. Vision scientists aim to accurately present both static and dynamic stimuli on their display devices. As for the presentation of static stimuli, we demonstrate an increased accuracy for LCD and OLED devices compared to CRT monitors, because the former exhibit a higher degree of independence of neighboring pixels. As for dynamic presentations, both CRTs and OLEDs outperform LCD devices in terms of accuracy, because dynamic presentations on LCDs require a reorientation of the liquid crystal molecules, so that successive frames in time depend on each other. Together with widely unknown and uncontrolled technical artifacts, these properties of LCDs may impair visual experiments that require high temporal precision. Therefore, OLED monitors are more suitable for vision science experiments with respect to both their static and their temporal characteristics. However, for certain applications in visual neuroscience, the low duty cycle of some OLED devices may introduce frequencies to the photometric output which fall within the window of visibility of neurons in the visual cortex and therefore interfere with single unit recordings.

  20. Recovery Act: Low Cost Integrated Substrate for OLED Lighting Development

    Energy Technology Data Exchange (ETDEWEB)

    Benton, Scott [PPG Industries, Inc., Pittsburgh, PA (United States); Bhandari, Abhinav [PPG Industries, Inc., Pittsburgh, PA (United States)

    2012-12-26

    PPG pursued the development of an integrated substrate, including the anode, external, and internal extraction layers. The objective of PPG's program was to achieve cost reductions by displacing the existing expensive borosilicate or double-side polished float glass substrates and developing alternative electrodes and scalable light extraction layer technologies through focused and short-term applied research. One of the key highlights of the project was proving the feasibility of using PPG's high transmission Solarphire® float glass as a substrate to consistently achieve organic lightemitting diode (OLED) devices with good performance and high yields. Under this program, four low-cost alternatives to the Indium Tin Oxide (ITO) anode were investigated using pilot-scale magnetron sputtered vacuum deposition (MSVD) and chemical vapor deposition (CVD) technologies. The anodes were evaluated by fabricating small and large phosphorescent organic lightemitting diode (PHOLED) devices at Universal Display Corporation (UDC). The device performance and life-times comparable to commercially available ITO anodes were demonstrated. A cost-benefit analysis was performed to down-select two anodes for further low-cost process development. Additionally, PPG developed and evaluated a number of scalable and compatible internal and external extraction layer concepts such as scattering layers on the outside of the glass substrate or between the transparent anode and the glass interface. In one external extraction layer (EEL) approach, sol-gel sprayed pyrolytic coatings were deposited using lab scale equipment by hand or automated spraying of sol-gel solutions on hot glass, followed by optimizing of scattering with minimal absorption. In another EEL approach, PPG tested large-area glass texturing by scratching a glass surface with an abrasive roller and acid etching. Efficacy enhancements of 1.27x were demonstrated using white PHOLED devices for 2.0mm substrates which are

  1. Synthesis of side-chain polystyrenes for all organic solution processed OLEDs

    OpenAIRE

    Lorente Sánchez, Alejandro Jose (Dr.)

    2017-01-01

    In the present work side-chain polystyrenes were synthesized and characterized, in order to be applied in multilayer OLEDs fabricated by solution process techniques. Manufacture of optoelectronic devices by solution process techniques is meant to decrease significantly fabrication cost and allow large scale production of such devices. This dissertation focusses in three series, enveloped in two material classes. The two classes differ to each other in the type of charge transport exhibited...

  2. Efficient organic light emitting-diodes (OLEDs)

    CERN Document Server

    Chang, Yi-Lu

    2015-01-01

    Following two decades of intense research globally, the organic light-emitting diode (OLED) has steadily emerged as the ultimate display technology of choice for the coming decades. Portable active matrix OLED displays have already become prevalent, and even large-sized ultra-high definition 4K TVs are being mass-produced. More exotic applications such as wearable displays have been commercialized recently. With the burgeoning success in displays, researchers are actively bringing the technology forward into the exciting solid-state lighting market. This book presents the knowledge needed for

  3. Efficient, deep-blue TADF-emitters for OLED display applications (Conference Presentation)

    Science.gov (United States)

    Volz, Daniel; Baumann, Thomas

    2016-09-01

    Currently, the mobile display market is strongly shifting towards AMOLED technology, in order to enable curved and flexible displays. This leads to a growing demand for highly efficient OLED emitters to reduce the power consumption and increase display resolution at the same time. While highly efficient green and red OLEDs already found their place in commercial OLED-displays, the lack of efficient blue emitters is still an issue. Consequently, the active area for blue is considerably larger than for green and red pixels, to make up for the lower efficiency. We intend to close this efficiency-gap with novel emitters based on thermally activated delayed fluorescence (TADF) technology. Compared to state-of-the-art fluorescent dopants, the efficiency of TADF-emitters is up to four times higher. At the same time, it is possible to design them in a way to maintain deep blue emission, i.e. CIE y < 0.2. These aspects are relevant to produce efficient high resolution AMOLED displays. Apart from these direct customer benefits, our TADF technology does not contain any rare elements, which allows for the fabrication of sustainable OLED technology. In this work, we highlight one of our recently developed blue TADF materials. Basic material properties as well as first device results are discussed. In a bottom-emitting device, a CIEx/CIEy coordinate of (0.16/0.17) was achieved with efficiency values close to 20% EQE.

  4. Efficiency and stability of different tris(8-hydroxyquinoline) aluminium (Alq3) derivatives in OLED applications

    International Nuclear Information System (INIS)

    Kwong, C.Y.; Djurisic, A.B.; Choy, W.C.H.; Li, D.; Xie, M.H.; Chan, W.K.; Cheah, K.W.; Lai, P.T.; Chui, P.C.

    2005-01-01

    In this work, we have investigated the material stability and organic light emitting diode (OLED) performance for tris-(8-hydroxyquinoline) aluminium (Alq 3 ) and for three of the Alq 3 derivatives. For each material, electron spin resonance (ESR) measurements were performed and the degradation of photoluminescence (PL) with atmosphere exposure was studied. Performance of OLEDs based on these materials was also studied. The device structure was ITO/N,N'-di(naphthalene-1-yl)-N,N'-diphenyl-benzidine (NPB) (50 nm)/Alq 3 or Alq 3 derivatives (60 nm)/LiF (0.3 nm)/Al (60 nm). It was found that the rate of PL decay of the films correlates strongly with the existence of ESR signal. However, stability of OLEDs fabricated from these materials showed no direct relationship with PL decay in the films. This indicates that the dominant degradation mechanism in OLEDs is related to the passage of electric current through the device. Detailed discussion of the performances of four light emitting materials in terms of efficiency and stability is given

  5. OLED-based physiologically-friendly very low-color temperature illumination for night

    Science.gov (United States)

    Jou, Jwo-Huei; Shen, Shih-Ming; Tang, Ming-Chun; Chen, Pin-Chu; Chen, Szu-Hao; Wang, Yi-Shan; Chen, Chien-Chih; Wang, Ching-Chun; Hsieh, Chun-Yu; Lin, Chin-Chiao; Chen, Chien-Tien

    2012-09-01

    Numerous medical research studies reveal intense white or blue light to drastically suppress at night the secretion of melatonin (MLT), a protective oncostatic hormone. Lighting devices with lower color-temperature (CT) possess lesser MLT suppression effect based on the same luminance, explaining why physicians have long been calling for the development of lighting sources with low CT or free from blue emission for use at night to safeguard human health. We will demonstrate in the presentation the fabrication of OLED devices with very-low CT, especially those with CT much lower than that of incandescent bulbs (2500K) or even candles (2000K). Without any light extraction method, OLEDs with an around 1800K CT are easily obtainable with an efficacy of 30 lm/W at 1,000 nits. To also ensure high color-rendering to provide visual comfort, low CT OLEDs composing long wavelength dominant 5-spectrum emission have been fabricated. While keeping the color-rendering index as high as 85 and CT as low as 2100K, the resulting efficacy can also be much greater than that of incandescent bulbs (15 lm/W), proving these low CT OLED devices to be also capable of being energy-saving and high quality. The color-temperature can be further decreased to 1700K or lower upon removing the undesired short wavelength emission but on the cost of losing some color rendering index. It is hoped that the devised energy-saving, high quality low CT OLED could properly echo the call for a physiologically-friendly illumination for night, and more attention could be drawn to the development of MLT suppression-less non-white light.

  6. Deep-blue efficient OLED based on NPB with little efficiency roll-off under high current density

    Science.gov (United States)

    Liu, Jian

    2017-03-01

    NPB usually is used as a hole-transport layer in OLED. In fact, it is a standard pure blue-emission material. However, its light-emitting efficiency in OLED is low due to emissive nature of organic material. Herein, a deep-blue OLDE based on NPB was fabricated. The light-emitting efficiency of the device demonstrates a moderate value, and efficiency roll-off is little under high current density. The device demonstrates that the electroplex's emission decreases with increasing electric field intensity.

  7. On the origin of exciton formation in dye doped Alq{sub 3} OLEDs

    Energy Technology Data Exchange (ETDEWEB)

    Gomez, J.A. [FFCLRP-USP, Departamento de Fisica, Sao Paulo (Brazil); Castro, F.A. [National Physical Laboratory, Materials Division, Teddington (United Kingdom); Nueesch, F. [Empa, Swiss Federal Laboratories for Materials Testing and Research, Laboratory for Functional Polymers, Duebendorf (Switzerland); Zuppiroli, L. [Institut des Materiaux, EPFL, Laboratoire d' Optoelectronique des Materiaux Moleculaire, Lausanne (Switzerland); Graeff, C.F.O. [FC-UNESP, Departamento de Fisica, Sao Paulo (Brazil)

    2012-09-15

    Electrically Detected Magnetic Resonance (EDMR) was used to investigate the influence of dye doping on spin-dependent exciton formation in aluminum (III) 8-hydroxyquinoline (Alq{sub 3}) based Organic Light Emitting Diodes (OLEDs) with different device structures. 4-(dicyanomethylene)-2-methyl-6-{l_brace}2-[(4-diphenylamino)-phenyl]ethyl{r_brace}-4H-pyran (DCM-TPA) and 5,6,11,12-tetraphenylnaphthacene (Rubrene) were used as dopants. Results at room temperature show significant differences on the EDMR spectra (g-factor and linewidth) of doped and undoped devices. Signals from DCM-TPA and Rubrene dye doped OLEDs showed strong temperature dependence, with signal intensity increasing by 2 orders of magnitude below 200 K for DCM-TPA dye doped OLEDs and increasing by {proportional_to}1 order of magnitude below 225 K for the Rubrene dye doped device, while undoped devices shows almost no temperature dependence. By adding a ''spacer'' layer of undoped Alq{sub 3} at the recombination zone, changes in bias voltage were used to shift the recombination from doped to undoped region and correlate that with changes in the EDMR spectrum. Our results are indicating that charge trapping on the dopant followed by recombination is the main mechanism of light emission in the investigated devices. (orig.)

  8. Maal ei ole surnud / Jaan Elken

    Index Scriptorium Estoniae

    Elken, Jaan, 1954-

    2001-01-01

    Põhjamaade ja Baltikumi I maalibiennaal Rootsis Väsbys. Biennaali Rootsi-poolne kuraator ja kujundaja Ricardo Donoso, Eesti komplekti koostas Mare Pedanik. Eksponeeritud on Tiit Pääsukese, Ado Lille, Andres Toltsi, Kaido Ole, Jaan Elkeni tööd. Näituse ülevaade, eraldi peatutud Leedu ja Läti kunstnikel

  9. Povl Ole Fanger's impact ten years later

    DEFF Research Database (Denmark)

    d'Ambrosio Alfano, Francesca Romana; Olesen, Bjarne W.; Palella, Boris Igor

    2017-01-01

    This paper pays tribute to Povl Ole Fanger, the late professor at the Technical University of Denmark. His scientific studies, focused on the main parameters affecting indoor environmental quality, have inspired (and still inspire) professional design engineers and academic researchers on human t...

  10. "Kuhu kadunud oled ..." : [luuletused] / Aleksandr Belonogov

    Index Scriptorium Estoniae

    Belonogov, Aleksandr

    2004-01-01

    Sisu: "Kuhu kadunud oled ..." ; "Puude juured haaravad ..." ; "Nagu hiljuti eraldi teelt ..." ; "Kui kord enam mõista ma ..." ; Käänded ; Väravale on kirjutatud ; Rahvas ütleb. Eluloolisi andmeid autori kohta lk. 361. Luuletused paralleelselt udmurdi ja eesti keeles

  11. Single side Emitting Transparent OLED lamp

    NARCIS (Netherlands)

    Lifka, H.; Verschuren, C.A.; Bruls, D.M.; Tanase, C.

    2011-01-01

    Transparent OLEDs offer great potential for novel applications. Preferably, the light should be emitted from one side only. This can bedone to some extent by modifying electrode thicknesses, but at the cost of reduced transparency. Here, we demonstrate a new approach tomake single side emissive

  12. Designing High Efficient Solar Powered OLED Lighting Systems

    DEFF Research Database (Denmark)

    Ploug, Rasmus Overgaard; Poulsen, Peter Behrensdorff; Thorsteinsson, Sune

    2016-01-01

    for the 10 Wp version. Furthermore, we present measurements of state-of-the-art commercial available OLED with regards to the luminous flux, luminous efficacy, luminance homogeneity, temperature dependency and IV characteristic of the OLED panels. In addition, solar powered OLED product concepts are proposed.......OLEDs used in solar powered lighting applications is a market of the future. This paper reports the development of electronic Three-Port-Converters for PV OLED product integration in the low-power area respectively for 1-10 Wp and 10-50 Wp with a peak efficiency of 97% at 1.8 W of PV power...

  13. VEHIOT: Design and Evaluation of an IoT Architecture Based on Low-Cost Devices to Be Embedded in Production Vehicles.

    Science.gov (United States)

    Redondo, Jonatan Pajares; González, Lisardo Prieto; Guzman, Javier García; Boada, Beatriz L; Díaz, Vicente

    2018-02-06

    Nowadays, the current vehicles are incorporating control systems in order to improve their stability and handling. These control systems need to know the vehicle dynamics through the variables (lateral acceleration, roll rate, roll angle, sideslip angle, etc.) that are obtained or estimated from sensors. For this goal, it is necessary to mount on vehicles not only low-cost sensors, but also low-cost embedded systems, which allow acquiring data from sensors and executing the developed algorithms to estimate and to control with novel higher speed computing. All these devices have to be integrated in an adequate architecture with enough performance in terms of accuracy, reliability and processing time. In this article, an architecture to carry out the estimation and control of vehicle dynamics has been developed. This architecture was designed considering the basic principles of IoT and integrates low-cost sensors and embedded hardware for orchestrating the experiments. A comparison of two different low-cost systems in terms of accuracy, acquisition time and reliability has been done. Both devices have been compared with the VBOX device from Racelogic, which has been used as the ground truth. The comparison has been made from tests carried out in a real vehicle. The lateral acceleration and roll rate have been analyzed in order to quantify the error of these devices.

  14. VEHIOT: Design and Evaluation of an IoT Architecture Based on Low-Cost Devices to Be Embedded in Production Vehicles

    Science.gov (United States)

    Díaz, Vicente

    2018-01-01

    Nowadays, the current vehicles are incorporating control systems in order to improve their stability and handling. These control systems need to know the vehicle dynamics through the variables (lateral acceleration, roll rate, roll angle, sideslip angle, etc.) that are obtained or estimated from sensors. For this goal, it is necessary to mount on vehicles not only low-cost sensors, but also low-cost embedded systems, which allow acquiring data from sensors and executing the developed algorithms to estimate and to control with novel higher speed computing. All these devices have to be integrated in an adequate architecture with enough performance in terms of accuracy, reliability and processing time. In this article, an architecture to carry out the estimation and control of vehicle dynamics has been developed. This architecture was designed considering the basic principles of IoT and integrates low-cost sensors and embedded hardware for orchestrating the experiments. A comparison of two different low-cost systems in terms of accuracy, acquisition time and reliability has been done. Both devices have been compared with the VBOX device from Racelogic, which has been used as the ground truth. The comparison has been made from tests carried out in a real vehicle. The lateral acceleration and roll rate have been analyzed in order to quantify the error of these devices. PMID:29415507

  15. VEHIOT: Design and Evaluation of an IoT Architecture Based on Low-Cost Devices to Be Embedded in Production Vehicles

    Directory of Open Access Journals (Sweden)

    Jonatan Pajares Redondo

    2018-02-01

    Full Text Available Nowadays, the current vehicles are incorporating control systems in order to improve their stability and handling. These control systems need to know the vehicle dynamics through the variables (lateral acceleration, roll rate, roll angle, sideslip angle, etc. that are obtained or estimated from sensors. For this goal, it is necessary to mount on vehicles not only low-cost sensors, but also low-cost embedded systems, which allow acquiring data from sensors and executing the developed algorithms to estimate and to control with novel higher speed computing. All these devices have to be integrated in an adequate architecture with enough performance in terms of accuracy, reliability and processing time. In this article, an architecture to carry out the estimation and control of vehicle dynamics has been developed. This architecture was designed considering the basic principles of IoT and integrates low-cost sensors and embedded hardware for orchestrating the experiments. A comparison of two different low-cost systems in terms of accuracy, acquisition time and reliability has been done. Both devices have been compared with the VBOX device from Racelogic, which has been used as the ground truth. The comparison has been made from tests carried out in a real vehicle. The lateral acceleration and roll rate have been analyzed in order to quantify the error of these devices.

  16. Tunable color parallel tandem organic light emitting devices with carbon nanotube and metallic sheet interlayers

    Energy Technology Data Exchange (ETDEWEB)

    Oliva, Jorge; Desirena, Haggeo; De la Rosa, Elder [Centro de Investigaciones en Optica, A.P. 1-948, León, Guanajuato 37160 (Mexico); Papadimitratos, Alexios [Solarno Inc., Coppell, Texas 75019 (United States); University of Texas at Dallas, Richardson, Texas 75080 (United States); Zakhidov, Anvar A., E-mail: Zakhidov@utdallas.edu [Solarno Inc., Coppell, Texas 75019 (United States); University of Texas at Dallas, Richardson, Texas 75080 (United States); Energy Efficiency Center, National University of Science and Technology, MISiS, Moscow 119049 (Russian Federation)

    2015-11-21

    Parallel tandem organic light emitting devices (OLEDs) were fabricated with transparent multiwall carbon nanotube sheets (MWCNT) and thin metal films (Al, Ag) as interlayers. In parallel monolithic tandem architecture, the MWCNT (or metallic films) interlayers are an active electrode which injects similar charges into subunits. In the case of parallel tandems with common anode (C.A.) of this study, holes are injected into top and bottom subunits from the common interlayer electrode; whereas in the configuration of common cathode (C.C.), electrons are injected into the top and bottom subunits. Both subunits of the tandem can thus be monolithically connected functionally in an active structure in which each subunit can be electrically addressed separately. Our tandem OLEDs have a polymer as emitter in the bottom subunit and a small molecule emitter in the top subunit. We also compared the performance of the parallel tandem with that of in series and the additional advantages of the parallel architecture over the in-series were: tunable chromaticity, lower voltage operation, and higher brightness. Finally, we demonstrate that processing of the MWCNT sheets as a common anode in parallel tandems is an easy and low cost process, since their integration as electrodes in OLEDs is achieved by simple dry lamination process.

  17. Low roll-off and high efficiency orange OLEDs using green and red dopants in an exciplex forming co-host

    Science.gov (United States)

    Lee, Sunghun; Kim, Kwon-Hyeon; Yoo, Seung-Jun; Park, Young-Seo; Kim, Jang-Joo

    2013-09-01

    We present high efficiency orange emitting OLEDs with low driving voltage and low roll-off of efficiency using an exciplex forming co-host by (1) co-doping of green and red emitting phosphorescence dyes in the host and (2) red and green phosphorescent dyes doped in the host as separate red and green emitting layers. The orange OLEDs achieved a low turn-on voltage of 2.4 V and high external quantum efficiencies (EQE) of 25.0% and 22.8%, respectively. Moreover, the OLEDs showed low roll-off of efficiency with an EQE of over 21% and 19.6% at 10,000 cd/m2, respectively. The devices displayed good orange color with very little color shift with increasing luminance. The transient electroluminescence of the OLEDs indicated that both energy transfer and direct charge trapping took place in the devices.

  18. The Trombe Wall during the 1970s: technological device or architectural space? Critical inquiry on the Trombe Wall in Europe and the role of architectural magazines

    Directory of Open Access Journals (Sweden)

    Piero Medici

    2017-12-01

    Full Text Available During the 1970s, before and after the international oil crisis of 1973, some European architectural periodicals were critical of standard construction methods and the architecture of the time. They described how architects and engineers reacted to the crisis, proposing new techniques and projects in order to intervene innovatively in the built environment, using energy and natural resources more efficiently. This article will provide a critical analysis of the role of architectural magazines of the time, describing the technological innovation of the Trombe Wall in Europe. It will treat when, how, and what specific aspects were described. It will also carry out a critical analysis of the Trombe Wall itself: about its performances, its evolution throughout the 1970s, its integration in different houses, and its influence on inhabitants’ behaviour. Using three houses as case studies, an analysis of the architects’ efforts to integrate the technology of the Trombe Wall with architectural elements such as shape, aesthetic, materiality, and natural light will be carried out. Though this article is historical in character, it aims to inform the contemporary debate, especially concerning issues of the built environment meeting the Paris agreement on climate change (AA, 2015.

  19. Molecular electrophosphorescence in (Sm, Gd)-{beta}-diketonate complex blend for OLED applications

    Energy Technology Data Exchange (ETDEWEB)

    Reyes, R., E-mail: fisicaplic@hotmail.com [Facultad de Ingenieria Quimica y Textil, Universidad Nacional de Ingenieria, UNI, Av. Tupac Amaru 210, Lima 31, Peru (Peru); Cremona, M. [DIMAT - Divisao de Metrologia de Materiais, Instituto Nacional de Metrologia, Normalizacao e Qualidade Industrial, INMETRO, Duque de Caxias, RJ (Brazil); Departamento de Fisica, Pontificia Universidade Catolica do Rio de Janeiro, PUC-Rio, C.P. 38071, Rio de Janeiro, RJ, CEP 22453-970 (Brazil); Teotonio, E.E.S. [Departamento de Quimica, CCEN, Universidade Federal da Paraiba, UFPB, C.P. 5093, Joao Pessoa, PB, CEP 5805-970 (Brazil); Brito, H.F. [Instituto de Quimica, Universidade de Sao Paulo, USP, C.P. 26077, Sao Paulo, SP, CEP 05599-970 (Brazil); Malta, O.L. [Departamento de Quimica Fundamental, CCEN, Universidade Federal de Pernambuco, Cidade Universitaria, Recife, PE, CEP 50670-901 (Brazil)

    2013-02-15

    In this work the preparation and characterization of the triple-layer organic light-emitting diode (OLED) using a mixture of the samarium and gadolinium {beta}-diketonate complexes [Sm{sub 0.5}Gd{sub 0.5}(TTA){sub 3}(TPPO){sub 2}] as emitting layer is reported. The OLED's devices contain 1-(3-methylphenyl)-1,2,3,4-tetrahydroquinoline-6-carboxyaldehyde-1, 1'-diphenylhydrazone (MTCD) as hole-transporting layer and tris(8-hydroxyquinoline aluminum) (Alq{sub 3}) as electron transporting layer. The electroluminescence spectrum present emission narrow bands from the {sup 4}G{sub 5/2}{yields}{sup 6}H{sub J} transitions (where J=5/2, 7/2 and 9/2) characteristic of the Sm{sup 3+} ion. These sharp lines are overlapped with a broad band attributed to the electrophosphorescence from the T{sub 1}{yields}S{sub 0} transition in the ligand TTA. The intramolecular energy transfer is discussed and applied on the change of the emission color of the organic LEDs at different bias voltages. - Highlights: Black-Right-Pointing-Pointer Samarium and gadolinium complexes. Black-Right-Pointing-Pointer OLED with complex blend (Sm,Gd). Black-Right-Pointing-Pointer Electrophosphorescence emission detection. Black-Right-Pointing-Pointer Application in OLED changing the color emission.

  20. OLED-based biosensing platform with ZnO nanoparticles for enzyme immobilization

    Science.gov (United States)

    Cai, Yuankun; Shinar, Ruth; Shinar, Joseph

    2009-08-01

    Organic light-emitting diode (OLED)-based sensing platforms are attractive for photoluminescence (PL)-based monitoring of a variety of analytes. Among the promising OLED attributes for sensing applications is the thin and flexible size and design of the OLED pixel array that is used for PL excitation. To generate a compact, fielddeployable sensor, other major sensor components, such as the sensing probe and the photodetector, in addition to the thin excitation source, should be compact. To this end, the OLED-based sensing platform was tested with composite thin biosensing films, where oxidase enzymes were immobilized on ZnO nanoparticles, rather than dissolved in solution, to generate a more compact device. The analytes tested, glucose, cholesterol, and lactate, were monitored by following their oxidation reactions in the presence of oxygen and their respective oxidase enzymes. During such reactions, oxygen is consumed and its residual concentration, which is determined by the initial concentration of the above-mentioned analytes, is monitored. The sensors utilized the oxygen-sensitive dye Pt octaethylporphyrin, embedded in polystyrene. The enzymes were sandwiched between two thin ZnO layers, an approach that was found to improve the stability of the sensing probes.

  1. Molecular electrophosphorescence in (Sm, Gd)-β-diketonate complex blend for OLED applications

    International Nuclear Information System (INIS)

    Reyes, R.; Cremona, M.; Teotonio, E.E.S.; Brito, H.F.; Malta, O.L.

    2013-01-01

    In this work the preparation and characterization of the triple-layer organic light-emitting diode (OLED) using a mixture of the samarium and gadolinium β-diketonate complexes [Sm 0.5 Gd 0.5 (TTA) 3 (TPPO) 2 ] as emitting layer is reported. The OLED's devices contain 1-(3-methylphenyl)-1,2,3,4-tetrahydroquinoline-6-carboxyaldehyde-1, 1'-diphenylhydrazone (MTCD) as hole-transporting layer and tris(8-hydroxyquinoline aluminum) (Alq 3 ) as electron transporting layer. The electroluminescence spectrum present emission narrow bands from the 4 G 5/2 → 6 H J transitions (where J=5/2, 7/2 and 9/2) characteristic of the Sm 3+ ion. These sharp lines are overlapped with a broad band attributed to the electrophosphorescence from the T 1 →S 0 transition in the ligand TTA. The intramolecular energy transfer is discussed and applied on the change of the emission color of the organic LEDs at different bias voltages. - Highlights: ► Samarium and gadolinium complexes. ► OLED with complex blend (Sm,Gd). ► Electrophosphorescence emission detection. ► Application in OLED changing the color emission.

  2. Application of Developed APCVD Transparent Conducting Oxides and Undercoat Technologies for Economical OLED Lighting

    Energy Technology Data Exchange (ETDEWEB)

    Silverman, Gary S.; Bluhm, Martin; Coffey, James; Korotkov, Roman; Polsz, Craig; Salemi, Alexandre; Smith, Robert; Smith, Ryan; Stricker, Jeff; Xu, Chen; Shirazi, Jasmine; Papakonstantopulous, George; Carson, Steve; Hartmann, Sören; Jessen, Frank; Krogmann, Bianaca; Rickers, Christoph; Ruske, Manfred; Schwab, Holger; Bertram, Dietrich

    2011-01-02

    Economics is a key factor for application of organic light emitting diodes (OLED) in general lighting relative to OLED flat panel displays that can handle high cost materials such as indium tin oxide (ITO) or Indium zinc oxide (IZO) as the transparent conducting oxide (TCO) on display glass. However, for OLED lighting to penetrate into general illumination, economics and sustainable materials are critical. The issues with ITO have been documented at the DOE SSL R&D and Manufacturing workshops for the last 5 years and the issue is being exaserbated by export controls from China (one of the major sources of elemental indium). Therefore, ITO is not sustainable because of the fluctuating costs and the United States (US) dependency on other nations such as China. Numerous alternatives to ITO/IZO are being evaluated such as Ag nanoparticles/nanowires, carbon nanotubes, graphene, and other metal oxides. Of these other metal oxides, doped zinc oxide has attracted a lot of attention over the last 10 years. The volume of zinc mined is a factor of 80,000 greater than indium and the US has significant volumes of zinc mined domestically, resulting in the ability for the US to be self-sufficient for this element that can be used in optoelectonic applications. The costs of elemental zinc is over 2 orders of magnitude less than indium, reflecting the relative abundance and availablility of the elements. Arkema Inc. and an international primary glass manufacturing company, which is located in the United States, have developed doped zinc oxide technology for solar control windows. The genesis of this DOE SSL project was to determine if doped zinc oxide technology can be taken from the commodity based window market and translate the technology to OLED lighting. Thus, Arkema Inc. sought out experts, Philips Lighting, Pacific Northwest National Laboratories (PNNL) and National Renewable Research Laboratories (NREL), in OLED devices and brought them into the project. This project had a

  3. Compute-unified device architecture implementation of a block-matching algorithm for multiple graphical processing unit cards.

    Science.gov (United States)

    Massanes, Francesc; Cadennes, Marie; Brankov, Jovan G

    2011-07-01

    In this paper we describe and evaluate a fast implementation of a classical block matching motion estimation algorithm for multiple Graphical Processing Units (GPUs) using the Compute Unified Device Architecture (CUDA) computing engine. The implemented block matching algorithm (BMA) uses summed absolute difference (SAD) error criterion and full grid search (FS) for finding optimal block displacement. In this evaluation we compared the execution time of a GPU and CPU implementation for images of various sizes, using integer and non-integer search grids.The results show that use of a GPU card can shorten computation time by a factor of 200 times for integer and 1000 times for a non-integer search grid. The additional speedup for non-integer search grid comes from the fact that GPU has built-in hardware for image interpolation. Further, when using multiple GPU cards, the presented evaluation shows the importance of the data splitting method across multiple cards, but an almost linear speedup with a number of cards is achievable.In addition we compared execution time of the proposed FS GPU implementation with two existing, highly optimized non-full grid search CPU based motion estimations methods, namely implementation of the Pyramidal Lucas Kanade Optical flow algorithm in OpenCV and Simplified Unsymmetrical multi-Hexagon search in H.264/AVC standard. In these comparisons, FS GPU implementation still showed modest improvement even though the computational complexity of FS GPU implementation is substantially higher than non-FS CPU implementation.We also demonstrated that for an image sequence of 720×480 pixels in resolution, commonly used in video surveillance, the proposed GPU implementation is sufficiently fast for real-time motion estimation at 30 frames-per-second using two NVIDIA C1060 Tesla GPU cards.

  4. Assessment of building facade performance in terms of daylighting and the associated energy consumption in architectural spaces: Vertical and horizontal shading devices for southern exposure facades

    Energy Technology Data Exchange (ETDEWEB)

    Alzoubi, Hussain H.; Al-Zoubi, Amneh H. [Department of Architecture, Jordan University of Science and Technology, Irbid 22110 (Jordan)

    2010-08-15

    This paper examines the effect of vertical and horizontal shading devices on the quality of daylight in buildings and the associated energy saving. Excessive daylight in architectural spaces contributes negatively to the energy consumption in buildings. Blinds and shading devices are good solutions to attenuate the surplus amount of daylight in spaces. Accordingly, this study evaluates the effect of shading devices on the amount of light flux and the associated solar energy in buildings. It estimates the energy consumption attributed to lighting spaces for three common positions of shading devices. Computer simulation strategy was undertaken to correlate the illuminance level in spaces with room geometry and architectural shading elements. The Holophane model for lighting calculations was used to estimate the average illuminance level on workplane and correlate it with the expected saving energy in buildings. The study concluded that there is an optimal orientation for shading devices that keeps the internal illuminance level within the acceptable range with minimum amount of solar heat gain. (author)

  5. OLED Hybrid Integrated Polymer Microfluidic Biosensing for Point of Care Testing

    Directory of Open Access Journals (Sweden)

    Ashwin Acharya

    2015-09-01

    Full Text Available This paper reports a microfluidic platform with external hybrid integration of an organic light emitting diode (OLED as an excitation source. This device can be used as a simple and cost effective biosensing element. The device is capable of rapid in-situ detection of biological elements such as sensing of interaction of antigen with fluorescent tagged antibody conjugates. These portable microfluidic systems have great potential for use an OLED in a single chip with very high accuracy and sensitivity for various point-of-care (POC diagnosis and lab on a chip (LOC applications, as the miniaturization of the biosensor is essential for handling smaller sample volumes in order to achieve high throughput. The biosensing element was successfully tested to detect anti-sheep IgG conjugates tagged to Alexafluor using a fluorescence based immunoassay method.

  6. Transparent conductive oxides and alternative transparent electrodes for organic photovoltaics and OLEDs; Transparente leitfaehige Elektroden. Oxide und alternative Materialien fuer die organische Photovoltaik und OLEDs

    Energy Technology Data Exchange (ETDEWEB)

    Mueller-Meskamp, Lars; Sachse, Christoph; Kim, Yong Hyun; Furno, Mauro [Technische Univ. Dresden (DE). Inst. fuer Angewandte Photophysik (IAPP); May, Christian [Fraunhofer Institut fuer Photonische Mikrosysteme (IPMS), Dresden (Germany); Leo, Karl [Technische Univ. Dresden (DE). Inst. fuer Angewandte Photophysik (IAPP); Fraunhofer Institut fuer Photonische Mikrosysteme (IPMS), Dresden (Germany)

    2012-08-15

    Organic, photoactive devices, such as OLEDs or organic solar cells, currently use indium tin oxide (ITO) as transparent electrode. Whereas ITO is industry-proven for many years and shows very good electrical and optical properties, its application for low-cost and flexible devices might not be optimal. For such applications innovative technologies such as network-based metal nanowire or carbon nanotube electrodes, graphene, conductive polymers, metal thin-films and alternative transparent conductive oxides emerge. Although some of these technologies are rather experimental and far from application, some of them have the potential to replace ITO in selected applications. (orig.)

  7. Synthesis of Some Green Dopants for OLEDs Based on Arylamine 2,3-disubstituted Bithiophene Derivatives

    Directory of Open Access Journals (Sweden)

    Mi-Seon Song

    2013-11-01

    Full Text Available A series of green dopants based on 2,2-diphenylvinyl end-capped bithiophene and three different arylamine moieties (9-phenylcarbazole, triphenylamine, and N,N’-di-(p-tolylbenzeneamine were successfully synthesized by the Suzuki and Wittig coupling reactions. The photophysical properties of these compounds are reported. The strongest PL emitting compound with the 9-phenylcarbazole moiety has been used for fabricating an OLED device with good overall performance.

  8. OLED Display For Real Time Vision System

    OpenAIRE

    Sandhyalakshmi Narayanan; Sanjana Sridhar; Neha Deshpande; Ashwini Gaikwad

    2015-01-01

    This innovative glass design will carry an OLED based display controlled via nano Ardiuno board having Bluetooth connectivity with a Smartphone to exchange information along with onboard accelerometer. We are using a tilt angle sensor for detecting if the driver is feeling drowsy. An alcohol sensor has been used to promote the safe driving habit. The glasses will be getting latest updates about the current speed of the vehicle navigation directions nearby or approaching sign broads or service...

  9. The enhanced electron injection by fluorinated tris-(8-hydroxy-quinolinato) aluminum derivatives in high efficient Si-anode OLEDs

    Energy Technology Data Exchange (ETDEWEB)

    Liu, N. [State Key Laboratory of Silicon Materials, MOE Key Laboratory of Macromolecule Synthesis and Functionalization, Department of Polymer Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Shi, M.M., E-mail: minminshi@zju.edu.c [State Key Laboratory of Silicon Materials, MOE Key Laboratory of Macromolecule Synthesis and Functionalization, Department of Polymer Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Li, Y.Z. [School of Physics, State Key Laboratory for Mesoscopic Physics, Peking University, Beijing 100871 (China); Shi, Y.W. [State Key Laboratory of Silicon Materials, MOE Key Laboratory of Macromolecule Synthesis and Functionalization, Department of Polymer Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Ran, G.Z.; Qin, G.G. [School of Physics, State Key Laboratory for Mesoscopic Physics, Peking University, Beijing 100871 (China); Wang, M.; Chen, H.Z. [State Key Laboratory of Silicon Materials, MOE Key Laboratory of Macromolecule Synthesis and Functionalization, Department of Polymer Science and Engineering, Zhejiang University, Hangzhou 310027 (China)

    2011-02-15

    Fabrication of organic light-emitting diodes (OLEDs) and lasers on silicon substrates is a feasible route to integrate microelectronic chips with optical devices for telecommunications. However, the efficiency of Si-anode based OLEDs is restricted by the imbalance of hole-electron injection because a p-type Si anode owns better hole injection ability than ITO. We have used fluorinated tris-(8-hydroxy-quinolinato) aluminum (FAlq{sub 3}) derivatives to prepare Si-anode based OLEDs. We observed that, when tris-(5-fuloro-8-hydroxyquinolinato) aluminum (5FAlq{sub 3}) is used as the electron-transporting material instead of Alq{sub 3}, the cathode electron injection is enhanced due to its lower lowest unoccupied molecular orbital (LUMO) compared to the Alq{sub 3}. The device can keep the relative carrier balance even when a Si anode capable of stronger hole injection was used. Further optimization of the device structure by introducing 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP) as a hole blocking layer showed significant increase in the device power efficiency from 0.029 to 0.462 lm/W. This indicates that use of fluorinated Alq{sub 3} derivatives is an effective way to improve the performance of Si-anode based OLEDs.

  10. Degradation in organic light emitting devices

    Science.gov (United States)

    Dinh, Vincent Vinh

    This thesis is about the fundamental causes of degradation in tris(8-Hydroxyquinoline) Aluminum (Alq3)-based organic light emitting diodes (OLEDs). Degradation typically occurs when a current is forced through an insulating material. Since the insulator does not support conduction waves (in its ground state), chemical restructuring must occur to accommodate the current. OLEDs have many technical advantages over the well known semiconductor-based light emitting diodes (LEDs). OLEDs have quantum efficiencies ˜1% (˜10 times higher than the LEDs), and operational power thresholds ˜.05mW (˜100 lower than the LEDs). OLEDs are preferred in power limited and portable devices; devices such as laptops and displays consume ˜1/4 of the supplied power---any power saving is significant. Other advantages, like better compliance to curved surfaces and ease of fabrication, give the OLEDs an even greater edge over the LEDs. OLEDs must have at least comparable or better lifetimes to remain attractive. Typical OLEDs last several 100hrs compared to the several 1000hrs for the LEDs. For reliable OLED application, it is necessary to understand the above breakdown mechanism. In this thesis, we attempt to understand the breakdown by looking at how OLEDs are made, how they work, and when they don't. In the opening sections, we give an overview of OLEDs and LEDs, especially how sustained luminescence is achieved through current circulation. Then in Chapter 2, we look at the basic components in the OLEDs. In Chapter 3 we look at how a hole material (like poly-vinyl carbazole or PVK) establishes an excitonic environment for the sustained luminescence in Alq3. We then approximate how potential is distributed when a simple luminescence system is in operation. In Chapter 4, we look at ways of measuring this distribution via the OLED impedance. Finally in Chapter 5, we look at the OLED stability under light emission conditions via PVK and Alq3 photoemission and photoabsorption spectra

  11. Application of Developed APCVD Transparent Conducting Oxides and Undercoat Technologies for Economical OLED Lighting

    Energy Technology Data Exchange (ETDEWEB)

    Martin Bluhm; James Coffey; Roman Korotkov; Craig Polsz; Alexandre Salemi; Robert Smith; Ryan Smith; Jeff Stricker; Chen Xu; Jasmine Shirazi; George Papakonstantopulous; Steve Carson; Claudia Goldman; Soren Hartmann; Frank Jessen; Bianca Krogmann; Christoph Rickers; Manfred Ruske; Holger Schwab; Dietrich Bertram

    2011-01-02

    Economics is a key factor for application of organic light emitting diodes (OLED) in general lighting relative to OLED flat panel displays that can handle high cost materials such as indium tin oxide (ITO) or Indium zinc oxide (IZO) as the transparent conducting oxide (TCO) on display glass. However, for OLED lighting to penetrate into general illumination, economics and sustainable materials are critical. The issues with ITO have been documented at the DOE SSL R&D and Manufacturing workshops for the last 5 years and the issue is being exacerbated by export controls from China (one of the major sources of elemental indium). Therefore, ITO is not sustainable because of the fluctuating costs and the United States (US) dependency on other nations such as China. Numerous alternatives to ITO/IZO are being evaluated such as Ag nanoparticles/nanowires, carbon nanotubes, graphene, and other metal oxides. Of these other metal oxides, doped zinc oxide has attracted a lot of attention over the last 10 years. The volume of zinc mined is a factor of 80,000 greater than indium and the US has significant volumes of zinc mined domestically, resulting in the ability for the US to be self-sufficient for this element that can be used in optoelectronic applications. The costs of elemental zinc is over 2 orders of magnitude less than indium, reflecting the relative abundance and availability of the elements. Arkema Inc. and an international primary glass manufacturing company, which is located in the United States, have developed doped zinc oxide technology for solar control windows. The genesis of this DOE SSL project was to determine if doped zinc oxide technology can be taken from the commodity based window market and translate the technology to OLED lighting. Thus, Arkema Inc. sought out experts, Philips Lighting, Pacific Northwest National Laboratories (PNNL) and National Renewable Research Laboratories (NREL), in OLED devices and brought them into the project. This project had a

  12. A novel AOI system for OLED panel inspection

    International Nuclear Information System (INIS)

    Perng, D B; Chen, Y C; Lee, M K

    2005-01-01

    Organic light emitting diode (OLED) technology uses substances that emit red, green, blue or white light. An OLED panel consists of stacks of several thin layers of different materials, as such it is not easy to inspect the common OLED defects. In this paper, an autooptical inspection (AOI) system which can detect such defects effectively and robustly was proposed and developed. The proposed system can also identify, in which layer the defect occurred. Meanwhile, a moving mechanism coupled with a lighting mechanism was proposed and implemented for grabbing clear images. The proposed AOI system would provide great help in improving the OLED production process and the quality control process

  13. Efficient electroluminescence from a perylenediimide fluorophore obtained from a simple solution processed OLED

    International Nuclear Information System (INIS)

    Cespedes-Guirao, F J; Fernandez-Lazaro, F; Sastre-Santos, A; Garcia-Santamaria, S; Bolink, H J

    2009-01-01

    Simple solution processed organic light emitting diodes are used to screen the performance of two types of highly efficient, narrow band red emitting fluorescent perylenediimides (PDIs). PDIs substituted at the diimide positions seem to form aggregates in the thin film architecture as evidenced by the shifted electroluminescent spectrum. When substituted on the bay position and when used both as the emitting and the electron transporting specie, bright electroluminescence with a narrow width around 610 nm reaching 500 cd m -2 at moderate voltages was observed, demonstrating the usefulness of these fluorophores for OLED applications.

  14. Simulation for light extraction efficiency of OLEDs with spheroidal microlenses in hexagonal array

    Science.gov (United States)

    Bae, Hyungchul; Kim, Jun Soo; Hong, Chinsoo

    2018-05-01

    A theoretical model based on ray optics is used to simulate the optical performance of organic light-emitting diodes (OLEDs) with spheroidal microlens arrays (MLAs) in a hexagonal array configuration using the Monte Carlo method. In simulations, ray tracing was performed until 20 reflections occurred from the metal cathode, with 10 consecutive reflections permitted in a single lens pattern. The parameters describing the shape and array of the lens pattern of a MLA are its radius, height, contact angle, and fill factor (FF). Many previous results on how these parameters affect light extraction efficiency (LEE) are inconsistent. In this paper, these contradictory results are discussed and explained by introducing a new parameter. To examine light extraction from an OLED through a MLA, the LEE enhancement is studied considering the effect of absorption by indium tin oxide during multiple reflections from the metal cathode. The device size where LEE enhancement is unchanged with changing lens pattern was identified for a fixed FF; under this condition, the optimal LEE enhancement, 84%, can be obtained using an OLED with a close-packed spheroidal MLA. An ideal maximum LEE enhancement of 120% was achieved with a device with an infinite-sized MLA. The angular intensity distribution of light emitted through a MLA is considered in addition to LEE enhancement for an optimized MLA.

  15. Thermally Cross-Linkable Hole Transport Materials for Solution Processed Phosphorescent OLEDs

    Science.gov (United States)

    Kim, Beom Seok; Kim, Ohyoung; Chin, Byung Doo; Lee, Chil Won

    2018-04-01

    Materials for unique fabrication of a solution-processed, multi-layered organic light-emitting diode (OLED) were developed. Preparation of a hole transport layer with a thermally cross-linkable chemical structure, which can be processed to form a thin film and then transformed into an insoluble film by using an amine-alcohol condensation reaction with heat treatment, was investigated. Functional groups, such as triplenylamine linked with phenylcarbazole or biphenyl, were employed in the chemical structure of the hole transport layer in order to maintain high triplet energy properties. When phenylcarbazole or biphenyl compounds continuously react with triphenylamine under acid catalysis, a chemically stable thin film material with desirable energy-level properties for a blue OLED could be obtained. The prepared hole transport materials showed excellent surface roughness and thermal stability in comparison with the commercial reference material. On the solution-processed model hole transport layer, we fabricated a device with a blue phosphorescent OLED by using sequential vacuum deposition. The maximum external quantum, 19.3%, was improved by more than 40% over devices with the commercial reference material (11.4%).

  16. Theoretical investigation of the degradation mechanisms in host and guest molecules used in OLED active layers

    KAUST Repository

    Winget, Paul

    2014-10-08

    A feature of OLEDs that has to date received little attention is the prediction of the stability of the molecules involved in the electrical and optical processes. Here, we present computational results intended to aid in the development of stable systems. We identify degradation pathways and define new strategies to guide the synthesis of stable materials for OLED applications for both phosphorescent emitters and organic host materials. The chemical reactivity of these molecules in the active layers of the devices is further complicated by the fact that, during operation, they can be either oxidized or reduced (as they localize a hole or an electron) in addition to forming both singlet and triplet excitons. © (2014) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.

  17. Efficiency enhancement of flexible OLEDs by using nano-corrugated substrates and conformal Ag transparent anodes

    Science.gov (United States)

    Wang, Li; Luo, Yu; Feng, Xueming; Pei, Yuechen; Lu, Bingheng; Cheng, Shenggui

    2018-05-01

    In flexible OLEDs (FOLEDs), the traditional ITO anode has disadvantages such as refractive-index mismatches among substrate and other functional layers, leads to light loss of nearly 80%, meanwhile, its brittle nature and lack in raw materials hinder its further applications. We investigated an efficient FOLED using a semi-transparent silver (Ag) anode, whereas the device was built on a nano-corrugated flexible polycarbonate (PC) substrate prepared by thermal nanoimprint lithography. The corrugations were well preserved on each layer of the device, both the micro-cavity effect and surface plasmon polariton (SPP) modes of light loss were effectively suppressed. As a result, the current efficiency of the FOLED using a conformal corrugated Ag anode enhanced by 100% compared with a planar Ag anode device, and enhanced by 13% with conventional ITO device. In addition, owing to the quasi-periodical arrangements of the corrugations, the device achieved broad spectra and Lambertian angular emission. The Ag anode significantly improved the bending properties of the OLED as compared to the conventional ITO device, leading to a longer lifetime in practical use. The proposed manufacturing strategy will be useful for fabricating nano corrugations on plastic substrate of FOLED in a cost-effective and convenient manner.

  18. Efficiency enhancement of flexible OLEDs by using nano-corrugated substrates and conformal Ag transparent anodes

    Directory of Open Access Journals (Sweden)

    Li Wang

    2018-05-01

    Full Text Available In flexible OLEDs (FOLEDs, the traditional ITO anode has disadvantages such as refractive-index mismatches among substrate and other functional layers, leads to light loss of nearly 80%, meanwhile, its brittle nature and lack in raw materials hinder its further applications. We investigated an efficient FOLED using a semi-transparent silver (Ag anode, whereas the device was built on a nano-corrugated flexible polycarbonate (PC substrate prepared by thermal nanoimprint lithography. The corrugations were well preserved on each layer of the device, both the micro-cavity effect and surface plasmon polariton (SPP modes of light loss were effectively suppressed. As a result, the current efficiency of the FOLED using a conformal corrugated Ag anode enhanced by 100% compared with a planar Ag anode device, and enhanced by 13% with conventional ITO device. In addition, owing to the quasi-periodical arrangements of the corrugations, the device achieved broad spectra and Lambertian angular emission. The Ag anode significantly improved the bending properties of the OLED as compared to the conventional ITO device, leading to a longer lifetime in practical use. The proposed manufacturing strategy will be useful for fabricating nano corrugations on plastic substrate of FOLED in a cost-effective and convenient manner.

  19. Principles of phosphorescent organic light emitting devices.

    Science.gov (United States)

    Minaev, Boris; Baryshnikov, Gleb; Agren, Hans

    2014-02-07

    Organic light-emitting device (OLED) technology has found numerous applications in the development of solid state lighting, flat panel displays and flexible screens. These applications are already commercialized in mobile phones and TV sets. White OLEDs are of especial importance for lighting; they now use multilayer combinations of organic and elementoorganic dyes which emit various colors in the red, green and blue parts of the visible spectrum. At the same time the stability of phosphorescent blue emitters is still a major challenge for OLED applications. In this review we highlight the basic principles and the main mechanisms behind phosphorescent light emission of various classes of photofunctional OLED materials, like organic polymers and oligomers, electron and hole transport molecules, elementoorganic complexes with heavy metal central ions, and clarify connections between the main features of electronic structure and the photo-physical properties of the phosphorescent OLED materials.

  20. Enhancement of white light OLED efficiency by combining both internal and external light extraction structures

    Science.gov (United States)

    Kao, I.-Ling; Ku, Chun-Neng; Chen, Yi-Ping; Lin, Ding-Zheng

    2012-09-01

    We proposed an internal nanostructure with a high reflective index planarization layer to solve the optical loss due to the reflective index mismatch between ITO and glass substrate. In our experiments, we found the electrical property of OLED device was significantly influenced by the internal nanostructures without planarization layer. Moreover, the internal extraction structure (IES) is not necessarily beneficial for light extraction. Therefore, we proposed a new substrate combine both internal and external extraction structure (EES) to extract trapping light. We successfully developed a high refractive index (N 1.7) planarization material with flat surface (RMS roughness < 2 nm), and improved about 70% device efficiency compared to traditional glass substrate.

  1. Electrical investigations of hybrid OLED microcavity structures with novel encapsulation methods

    Science.gov (United States)

    Meister, Stefan; Brückner, Robert; Fröb, Hartmut; Leo, Karl

    2016-04-01

    An electrical driven organic solid state laser is a very challenging goal which is so far well beyond reach. As a step towards realization, we monolithically implemented an Organic Light Emitting Diode (OLED) into a dielectric, high quality microcavity (MC) consisting of two Distributed Bragg Reectors (DBR). In order to account for an optimal optical operation, the OLED structure has to be adapted. Furthermore, we aim to excite the device not only electrically but optically as well. Different OLED structures with an emission layer consisting of Alq3:DCM (2 wt%) were investigated. The External Quantum Efficiencies (EQE) of this hybrid structures are in the range of 1-2 %, as expected for this material combination. Including metal layers into a MC is complicated and has a huge impact on the device performance. Using Transfer-Matrix-Algorithm (TMA) simulations, the best positions for the metal electrodes are determined. First, the electroluminescence (EL) of the adjusted OLED structure on top of a DBR is measured under nitrogen atmosphere. The modes showed quality factors of Q = 60. After the deposition of the top DBR, the EL is measured again and the quality factors increased up to Q = 600. Considering the two 25-nm-thick-silver contacts a Q-factor of 600 is very high. The realization of a suitable encapsulation method is important. Two approaches were successfully tested. The first method is based on the substitution of a DBR layer with a layer produced via Atomic Layer Deposition (ALD). The second method uses a 0.15-mm-thick cover glass glued on top of the DBR with a 0.23-μm-thick single-component glue layer. Due to the working encapsulation, it is possible to investigate the sample under ambient conditions.

  2. Ole Worm-Liv og videnskabTidstavle

    DEFF Research Database (Denmark)

    2006-01-01

    hæftet indeholder syv artikler om Ole Worms liv, videnskab, museum, slægtsportrætter, antikvariske arbejder og om installationen Room One......hæftet indeholder syv artikler om Ole Worms liv, videnskab, museum, slægtsportrætter, antikvariske arbejder og om installationen Room One...

  3. Kaido Ole seintel ja kaante vahel / Valner Valme

    Index Scriptorium Estoniae

    Valme, Valner, 1970-

    2007-01-01

    Kunstnik Kaido Ole (sünd. 1963) eluloolisi andmeid, looming. Eesti Kunstiakadeemia andis välja kataloogi "Ole", toimetaja Eero Epner. Kunstinäitus "Jonas & Kaido" koos Jonas Gasiunasega Vilniuse Vartai galeriis. Näitus "Hümn" Vaal galeriis

  4. The role of molecular architecture and layer composition on the properties and performance of CuPc-C6 photovoltaic devices

    International Nuclear Information System (INIS)

    Schultes, S.M.; Sullivan, P.; Heutz, S.; Sanderson, B.M.; Jones, T.S.

    2005-01-01

    We have studied the effects of molecular architecture, co-deposition and annealing on the properties and performance of photovoltaic cells based on copper phthalocyanine (CuPc)-fullerene (C 6 ) heterojunctions. Significant improvements in performance are achieved when mixed CuPc:C 6 layers are incorporated into the device structure due to the creation of an intermolecularly mixed donor (D)-acceptor (A) blend that favours efficient exciton dissociation. We utilise the control afforded by organic molecular beam deposition to show that the mixed-layer composition plays an important role in determining device performance and correlate device efficiency to the morphological and spectroscopic properties of the organic layers. A maximum power conversion efficiency of η p = 1.17% is achieved for devices containing a mixed layer of ratio 75:25 CuPc:C 6 surrounded by thin continuous layers of pure organic material at the electrode interfaces. A structure containing a compositional gradient where the CuPc:C 6 composition is varied from purely D to purely A via three mixed layers of increasing A composition leads to a further improvements in efficiency (η p = 1.36%). Finally, we use thermal annealing to show how structural defects and morphological templating of organic thin films reduces the interfacial area for exciton separation and yields poor device performance

  5. Photochemically induced emission tuning of conductive polumers used in OLEDs

    Energy Technology Data Exchange (ETDEWEB)

    Vasilopoulou, M [NCSR ' Demokritos' , Institute of Microelectronics, POB 60228, 153 10 Agia Paraskevi, Attiki (Greece); Pistolis, G [Institute of Physical Chemistry, NCSR ' Demokritos' Athens 153 10 (Greece); Argitis, P [NCSR ' Demokritos' , Institute of Microelectronics, POB 60228, 153 10 Agia Paraskevi, Attiki (Greece)

    2005-01-01

    The present work focuses on the use of novel patterning technology schemes for the fabrication of OLED-based displays and in particular on the definition of two colour emitting pixels in one polymeric conducting layer. The approach adopted to this end is based on photochemically induced emition tuning. On the basis of this approach a novel photolithographic patterning technique was developed, aiming at the considerable simplification of the display fabrication process and on the performance improvement. We prepared electroluminescent devices that are emitting blue colour ({lambda}{sub max} 413 nm) with a turnon voltage about 12-15 V. In other devices we introduce a dispersed dye (1-[4-(dimethylamino)phenyl]-6-phenylhexatriene) and a series of photoacid generators (onium salts) in the polymeric layer and, by using an appropriate photochemical transformation through a photomask in a single layer, we were able to change the colour to desirable direction, since the parent compound and its photochemical product have distinguishable luminescence spectra (green and blue colour respectively). We were able to produce two of the three primary colours in a single layer of a conductive polymer by using a photochemical transformation based on photoacid induced emission change. A series of photoacid generators were evaluated.

  6. OLED Display For Real Time Vision System

    Directory of Open Access Journals (Sweden)

    Sandhyalakshmi Narayanan

    2015-08-01

    Full Text Available This innovative glass design will carry an OLED based display controlled via nano Ardiuno board having Bluetooth connectivity with a Smartphone to exchange information along with onboard accelerometer. We are using a tilt angle sensor for detecting if the driver is feeling drowsy. An alcohol sensor has been used to promote the safe driving habit. The glasses will be getting latest updates about the current speed of the vehicle navigation directions nearby or approaching sign broads or services like petrol pumps. Itll also display information like incoming calls or received messages. All this information will be obtained through a Smartphone connected via Bluetooth. Also the car mileage can be monitored with help of fuel sensor as the consumption of fuel is directly related to it. Abnormalities if detected will be immediately notified in the glasses. Also the angle of the tilt angle sensor can be defined and set by the user according to his needs. Also the main idea of using OLED glasses is that it is organic thereby helps in reducing the carbon footprint and is quite slim. Therefore it can be easily mounted on the specs without making it heavy. Also they higher level of flexibility and have low power drain and energy consumption

  7. OLED-polypropylene bio-CD sensor

    Science.gov (United States)

    Vengasandra, Srikanth; Cai, Yuankun; Grewell, David; Shinar, Joseph; Shinar, Ruth

    2008-08-01

    With the goal of developing microfluidic platforms for sensing applications, flash-free micro patterns were embossed in polypropylene surfaces with ultrasonic heating for a biosensing lab-on-CD application. The embossed features were designed to act as reservoirs, valves, and reaction chambers to allow, in combination with a compact sensing platform, the monitoring of analyte levels using a standard PC-CD player. To generate the compact sensor, as an example, we chose the photoluminescence (PL)-based detection of lactate and glucose using an OLED-based sensing platform. Once embossed, the surface energy of the plastic substrate was chemically modified to make it hydrophilic. Reagents, placed in separate reservoirs, were directed through burst valves towards a reaction chamber via CD rotation. Lactate or glucose were monitored by measuring the effect of the related dissolved oxygen level on the PL decay time of an oxygen-sensitive dye, following analyte oxidation catalyzed by a suitable specific oxidase enzyme. The results demonstrate the potential of integrating OLEDs as excitation sources in PL-based sensors with microfluidic CD-based platforms, including for simultaneous multiple analyses.

  8. A flexible and testable software architecture: applying presenter first to a device server for the DOOCS accelerator control system of the European XFEL

    International Nuclear Information System (INIS)

    Beckmann, A.; Karabekyan, S.; Pflüger, J.

    2012-01-01

    Presenter First (PF) uses a variant of Model View Presenter design pattern to add implementation flexibility and to improve testability of complex event-driven applications. It has been introduced in the context of GUI applications, but can easily be adapted to server applications. This paper describes how Presenter First methodology is used to develop a device server for the Programmable Logic Controls (PLC) of the European XFEL undulator systems, which are Windows PCs running PLC software from Beckhoff. The server implements a ZeroMQ message interface to the PLC allowing the DOOCS accelerator control system of the European XFEL to exchange data with the PLC by sending messages over the network. Our challenge is to develop a well-tested device server with a flexible architecture that allows integrating the server into other accelerator control systems like EPICS. (author)

  9. Electrical properties of SAM-modified ITO surface using aromatic small molecules with double bond carboxylic acid groups for OLED applications

    International Nuclear Information System (INIS)

    Can, Mustafa; Havare, Ali Kemal; Aydın, Hasan; Yagmurcukardes, Nesli; Demic, Serafettin; Icli, Sıddık; Okur, Salih

    2014-01-01

    Graphical abstract: - Highlights: • We report that the performance of OLED consist of aromatic small molecules with double bond carboxylic acid groups on ITO surface. • The OLED devices were tested in terms of electrical and optical characteristics. • The I–V results show that OLEDs with SAM-modified ITO surface have lower turn on voltages than OLED configurations without SAMs. - Abstract: 5-[(3-Methylphenyl)(phenyl)amino]isophthalic acid (5-MePIFA) and 5-(diphenyl)amino]isophthalic acid (5-DPIFA) organic molecules were synthesized to form self-assembled monolayer on indium tin oxide (ITO) anode to enhance hole transport from ITO to organic hole transport layers such as TPD. The modified surface was characterized by scanning tunneling microscopy (STM). The change in the surface potential was measured by Kelvin probe force microscopy (KPFM). Our Kelvin probe force microscopy (KPFM) measurements showed that the surface potentials increased more than 100 mV with reference to bare indium tin-oxide. The results show that the threshold voltage on OLEDs with modified ITO is lowered significantly compared to OLEDs with unmodified ITO. The hole mobility of TPD has been estimated using space–charge-limited current measurements (SCLC)

  10. Electrical properties of SAM-modified ITO surface using aromatic small molecules with double bond carboxylic acid groups for OLED applications

    Energy Technology Data Exchange (ETDEWEB)

    Can, Mustafa [Izmir Katip Celebi University, Faculty of Engineering, Department of Engineering Sciences, Çiğli, Izmir (Turkey); Havare, Ali Kemal [Toros University, Faculty of Engineering, Electric and Electronic Department, Mersin (Turkey); Aydın, Hasan; Yagmurcukardes, Nesli [Izmir Institute of Technology, Material Science and Engineering, Izmir (Turkey); Demic, Serafettin [Izmir Katip Celebi University, Faculty of Engineering, Department of Material Science and Engineering, Çiğli, Izmir (Turkey); Icli, Sıddık [Ege University, Solar Energy Institute, Izmir (Turkey); Okur, Salih, E-mail: salih.okur@ikc.edu.tr [Izmir Katip Celebi University, Faculty of Engineering, Department of Material Science and Engineering, Çiğli, Izmir (Turkey)

    2014-09-30

    Graphical abstract: - Highlights: • We report that the performance of OLED consist of aromatic small molecules with double bond carboxylic acid groups on ITO surface. • The OLED devices were tested in terms of electrical and optical characteristics. • The I–V results show that OLEDs with SAM-modified ITO surface have lower turn on voltages than OLED configurations without SAMs. - Abstract: 5-[(3-Methylphenyl)(phenyl)amino]isophthalic acid (5-MePIFA) and 5-(diphenyl)amino]isophthalic acid (5-DPIFA) organic molecules were synthesized to form self-assembled monolayer on indium tin oxide (ITO) anode to enhance hole transport from ITO to organic hole transport layers such as TPD. The modified surface was characterized by scanning tunneling microscopy (STM). The change in the surface potential was measured by Kelvin probe force microscopy (KPFM). Our Kelvin probe force microscopy (KPFM) measurements showed that the surface potentials increased more than 100 mV with reference to bare indium tin-oxide. The results show that the threshold voltage on OLEDs with modified ITO is lowered significantly compared to OLEDs with unmodified ITO. The hole mobility of TPD has been estimated using space–charge-limited current measurements (SCLC)

  11. Remote Steric Effect as a Facile Strategy for Improving the Efficiency of Exciplex-Based OLEDs.

    Science.gov (United States)

    Hung, Wen-Yi; Wang, Ting-Chih; Chiang, Pin-Yi; Peng, Bo-Ji; Wong, Ken-Tsung

    2017-03-01

    This work reports a new strategy of introducing remote steric effect onto the electron donor for giving the better performance of the exciplex-based organic light-emitting device (OLED). The bulky triphenylsilyl group (SiPh 3 ) was introduced onto the fluorene bridge of 4,4'-(9H-fluorene-9,9-diyl)bis(N,N-di-p-tolylaniline) (DTAF) to create remote steric interactions for increasing the possibility of effective contacts between electron-donating chromophores and acceptor molecules, rendering the resulting exciplex to have a higher photoluminescence quantum yield (PLQY). The green exciplex device based on DSDTAF:3N-T2T (1:1) as an emitting layer exhibits a low turn-on voltage of 2.0 V, high maximum efficiencies (13.2%, 42.9 cd A -1 , 45.5 lm W -1 ), which are higher than the device employed DTAF (without SiPh 3 groups) (11.6%, 35.3 cd A -1 , 41.3 lm W -1 ) as donor under the same device structure. This strategy was further examined for blue exciplex, where the EQE was enhanced from 9.5% to 12.5% as the electron acceptor PO-T2T mixed with a tert-butyl group substituted carbazole-based donor (CPTBF) as the emitting exciplex in device. This strategy is simple and useful for developing high performance exciplex OLEDs.

  12. Non-Doped Sky-Blue OLEDs Based on Simple Structured AIE Emitters with High Efficiencies at Low Driven Voltages.

    Science.gov (United States)

    Islam, Amjad; Zhang, Dongdong; Peng, Ruixiang; Yang, Rongjuan; Hong, Ling; Song, Wei; Wei, Qiang; Duan, Lian; Ge, Ziyi

    2017-09-05

    Blue organic light-emitting diodes (OLEDs) are necessary for flat-panel display technologies and lighting applications. To make more energy-saving, low-cost and long-lasting OLEDs, efficient materials as well as simple structured devices are in high demand. However, a very limited number of blue OLEDs achieving high stability and color purity have been reported. Herein, three new sky-blue emitters, 1,4,5-triphenyl-2-(4-(1,2,2-triphenylvinyl)phenyl)-1H-imidazole (TPEI), 1-(4-methoxyphenyl)-4,5-diphenyl-2-(4-(1,2,2-triphenylvinyl)phenyl)-1H-imidazole (TPEMeOPhI) and 1-phenyl-2,4,5-tris(4-(1,2,2-triphenylvinyl)phenyl)-1H-imidazole (3TPEI), with a combination of imidazole and tetraphenylethene groups, have been developed. High photoluminescence quantum yields are obtained for these materials. All derivatives have demonstrated aggregation-induced emission (AIE) behavior, excellent thermal stability with high decomposition and glass transition temperatures. Non-doped sky-blue OLEDs with simple structure have been fabricated employing these materials as emitters and realized high efficiencies of 2.41 % (4.92 cd A -1 , 2.70 lm W -1 ), 2.16 (4.33 cd A -1 , 2.59 lm W -1 ) and 3.13 % (6.97 cd A -1 , 4.74 lm W -1 ) for TPEI, TPEMeOPhI and 3TPEI, with small efficiency roll-off. These are among excellent results for molecules constructed from the combination of imidazole and TPE reported so far. The high performance of a 3TPEI-based device shows the promising potential of the combination of imidazole and AIEgen for synthesizing efficient electroluminescent materials for OLED devices. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Novel Smart Windows Based on Transparent Phosphorescent OLEDs

    Energy Technology Data Exchange (ETDEWEB)

    Brian D' Andrade; Stephen Forest

    2006-09-15

    In this program, Universal Display Corporation (UDC) and Princeton University developed the use of white transparent phosphorescent organic light emitting devices (PHOLEDs{trademark}) to make low-cost ''transparent OLED (TOLED) smart windows'', that switch rapidly from being a highly efficient solid-state light source to being a transparent window. PHOLEDs are ideal for large area devices, and the UDC-Princeton team has demonstrated white PHOLEDs with efficiencies of >24 lm/W at a luminance of 1,000 cd/m{sup 2}. TOLEDs have transparencies >70% over the visible wavelengths of light, but their transparency drops to less than 5% for wavelengths shorter than 350 nm, so they can also be used as ultraviolet (UV) light filters. In addition to controlling the flow of UV radiation, TOLEDs coupled with an electromechanical or electrically activated reflecting shutter on a glass window can be employed to control the flow of heat from infrared (IR) radiation by varying the reflectance/transparency of the glass for wavelengths greater than 800nm. One particularly attractive shutter technology is reversible electrochromic mirrors (REM). Our goal was therefore to integrate two innovative concepts to meet the U.S. Department of Energy goals: high power efficiency TOLEDs, plus electrically controlled reflectors to produce a ''smart window''. Our efforts during this one year program have succeeded in producing a prototype smart window shown in the Fig. I, below. The four states of the smart window are pictured: reflective with lamp on, reflective with lamp off, transparent with lamp on, and transparent with lamp off. In the transparent states, the image is an outdoor setting viewed through the window. In the reflective states, the image is an indoor setting viewed via reflection off the window. We believe that the integration of our high efficiency white phosphorescent TOLED illumination source, with electrically activated shutters represents

  14. Organic light-emitting devices with fullerene/aluminum composite anode

    International Nuclear Information System (INIS)

    Song, Q.L.; Li, C.M.; Wang, M.L.; Sun, X.Y.

    2008-01-01

    Our previous work demonstrates that fullerene/Aluminum (C 60 /Al) can be used as a composite anode in organic solar cells. In this work, we report that an organic light emitting devices (OLEDs) can be made with the C 60 /Al composite anode as well. The OLEDs show comparable current density and brightness to the traditional devices with the indium tin oxide anode

  15. Chemical failure modes of AlQ3-based OLEDs: AlQ3 hydrolysis.

    Science.gov (United States)

    Knox, John E; Halls, Mathew D; Hratchian, Hrant P; Schlegel, H Bernhard

    2006-03-28

    Tris(8-hydroxyquinoline)aluminum(III), AlQ3, is used in organic light-emitting diodes (OLEDs) as an electron-transport material and emitting layer. The reaction of AlQ3 with trace H2O has been implicated as a major failure pathway for AlQ3-based OLEDs. Hybrid density functional calculations have been carried out to characterize the hydrolysis of AlQ3. The thermochemical and atomistic details for this important reaction are reported for both the neutral and oxidized AlQ3/AlQ3+ systems. In support of experimental conclusions, the neutral hydrolysis reaction pathway is found to be a thermally activated process, having a classical barrier height of 24.2 kcal mol(-1). First-principles infrared and electronic absorption spectra are compared to further characterize AlQ3 and the hydrolysis pathway product, AlQ2OH. The activation energy for the cationic AlQ3 hydrolysis pathway is found to be 8.5 kcal mol(-1) lower than for the neutral reaction, which is significant since it suggests a role for charge imbalance in promoting chemical failure modes in OLED devices.

  16. Fundamental processes governing operation and degradation in state of the art P-OLEDs

    Science.gov (United States)

    Roberts, Matthew; Asada, Kohei; Cass, Michael; Coward, Chris; King, Simon; Lee, Andrew; Pintani, Martina; Ramon, Miguel; Foden, Clare

    2010-05-01

    We present a theoretical and experimental analysis of operation and degradation of model fluorescent blue bilayer polymer organic light emitting diodes (P-OLED). Optical and electrical simulations of bilayer P-OLEDs are used to highlight the key material and device parameters required for efficient recombination and outcoupling of excitons. Mobility data for a model interlayer material poly (9,9-dioctylfluorene-N-(4-(2-butyl)phenyl)-diphenylamine) (TFB) and a model fluorescent blue light emitting material poly-(9,9'- dioctylfluorene-co-bis-N, N'-(4-butylphenyl)-bis-N,N'- phenyl-1,4-phenylenediamine) (95:5 mol%) (F8-PFB random copoloymer), is shown to satisfy the key charge transport characteristics required to ensure exciton formation at the optimum location for efficient extraction of the light where μh (LEP) 90%) of the quenching sites produced. This highlights the importance of understanding these reversible phenomena in improving P-OLED lifetime and commercial adoption of the technology.

  17. Investigation on a short circuit of large-area OLED lighting panels

    International Nuclear Information System (INIS)

    Park, J W; Kim, T W; Park, J B

    2013-01-01

    A short circuit often arises from large-area organic light-emitting device (OLED) lighting panels due to particles (i.e. dust, organic or metal debris) or the spike-like surface of the indium–tin–oxide (ITO) anode. On the emergence of a short circuit, an instant current crowding occurs, thereby reducing substantially the resistance of the panels and causing a failure of a dimming control. In this paper, we investigate the effect of the surface morphology of ITO on the resistance and dimmability of the panels. We have demonstrated that the peak-to-valley roughness of ITO should be much less than 20 nm or the resistance of the panels should be much higher than 1 MΩ in order to avoid an unwanted short-circuit phenomenon and thus achieve the high-yield fabrication of OLED lighting panels. It is also addressed that much care is taken to ensure a dimming control of OLED lighting panels with a larger active area because the resistance of those panels varies depending more sensitively on the surface roughness of ITO. (paper)

  18. Printing method for organic light emitting device lighting

    Science.gov (United States)

    Ki, Hyun Chul; Kim, Seon Hoon; Kim, Doo-Gun; Kim, Tae-Un; Kim, Snag-Gi; Hong, Kyung-Jin; So, Soon-Yeol

    2013-03-01

    Organic Light Emitting Device (OLED) has a characteristic to change the electric energy into the light when the electric field is applied to the organic material. OLED is currently employed as a light source for the lighting tools because research has extensively progressed in the improvement of luminance, efficiency, and life time. OLED is widely used in the plate display device because of a simple manufacture process and high emitting efficiency. But most of OLED lighting projects were used the vacuum evaporator (thermal evaporator) with low molecular. Although printing method has lower efficiency and life time of OLED than vacuum evaporator method, projects of printing OLED actively are progressed because was possible to combine with flexible substrate and printing technology. Printing technology is ink-jet, screen printing and slot coating. This printing method allows for low cost and mass production techniques and large substrates. In this research, we have proposed inkjet printing for organic light-emitting devices has the dominant method of thick film deposition because of its low cost and simple processing. In this research, the fabrication of the passive matrix OLED is achieved by inkjet printing, using a polymer phosphorescent ink. We are measured optical and electrical characteristics of OLED.

  19. Integration of OLE into the TACL control system

    International Nuclear Information System (INIS)

    Bowling, B.; Douglas, D.; Kewisch, J.; Kloeppel, P.; Kraft, G.A.

    1993-01-01

    OLE, the On-Line Envelope program, is a first-order optics code which was designed to provide fast lattice transfer functions from actual accelerator magnet and cavity control values. This paper addresses the results of a successful integration of OLE into the CEBAF control system, TACL. This marriage provides the user with the ability for obtaining real-time Twiss parameters and transfer functions which reflect the current operational state of the machine. The resultant OLE calculation provides the analytical core for many control and diagnostic functions used at CEBAF, including focusing corrections, orbit corrections, emittance measurements, and beamline analysis

  20. Structural, optical and electrical properties of europium picrate tetraethylene glycol complex as emissive material for OLED

    Energy Technology Data Exchange (ETDEWEB)

    Kusrini, Eny, E-mail: ekusrini@che.ui.ac.id [Department of Chemical Engineering, Faculty of Engineering, Universitas Indonesia, 16424 Depok (Indonesia); Saleh, Muhammad I.; Adnan, Rohana [School of Chemical Sciences, Universiti Sains Malaysia, 11800 Penang (Malaysia); Yulizar, Yoki [Department of Chemistry, Faculty of Mathematics and Natural Sciences, Universitas Indonesia, 16424 Depok (Indonesia); Sha Shiong, Ng; Fun, H.K. [School of Physics, Universiti Sains Malaysia, 11800 Penang (Malaysia); Adhha Abdullah, M.A.; Mamat, Mazidah [Department of Chemical Sciences, Faculty of Science and Technology, Universiti Malaysia Terengganu, 21030 Kuala Terengganu, Terengganu Darul Iman (Malaysia); Za' aba, N.K.; Abd. Majid, W.H. [Solid State Research Laboratory, Department of Physics, Universiti Malaya, 50603 Kuala Lumpur (Malaysia)

    2012-01-15

    A new europium complex [Eu(Pic){sub 2}(H{sub 2}O)(EO4)](Pic).0.75H{sub 2}O was synthesized and used as the emission material for the single layer device structure of ITO/EO4-Eu-Pic/Al, using a spin-coating technique. Study on the optical properties of the [Eu(Pic){sub 2}(H{sub 2}O)(EO4)](Pic).0.75H{sub 2}O complex where EO4=tetraethylene glycol and Pic=picrate anion, had to be undertaken before being applicable to the study of an organic light emitting diode (OLED). The electrical property of an OLED using current-voltage (I-V) measurement was also studied. In complex, the Eu(III) ion was coordinated with the EO4 ligand as a pentadentate mode, one water molecule, and with two Pic anions as bidentate and monodentate modes, forming a nine-coordination number. The photoluminescence (PL) spectra of the crystalline complex in the solid state and its thin film showed a hypersensitive peak at 613.5-614.9 nm that assigned to the {sup 5}D{sub 0}{yields}{sup 7}F{sub 2} transition. A narrow band emission from the thin film EO4-Eu-Pic was obtained. The typical semiconductor I-V curve of device ITO/EO4-Eu-Pic/Al showed the threshold and turn on voltages at 1.08 and 4.6 V, respectively. The energy transfer process from the ligand to the Eu(III) ion was discussed by investigating the excitation and PL characteristics. Effect of the picrate anion on the device performance was also studied. - Highlights: > The [Eu(Pic){sub 2}(H{sub 2}O)(EO4)](Pic).0.75(H{sub 2}O) is crystallized in triclinic with space group P-1. > The complex is applied as a emissive center in single layer device structure of ITO/EO4-Eu-Pic/Al. > The complex displays a red luminescence in both the crystalline complex and its thin film state. > The low turn on voltage of the device (4.6 V), indicating that this material is suitable for OLED. > The roughness and morphology of the thin film affects luminance and electrical properties of OLED.

  1. Spirobifluorene Core-Based Novel Hole Transporting Materials for Red Phosphorescence OLEDs

    Directory of Open Access Journals (Sweden)

    Ramanaskanda Braveenth

    2017-03-01

    Full Text Available Two new hole transporting materials, named HTM 1A and HTM 1B, were designed and synthesized in significant yields using the well-known Buchwald Hartwig and Suzuki cross- coupling reactions. Both materials showed higher decomposition temperatures (over 450 °C at 5% weight reduction and HTM 1B exhibited a higher glass transition temperature of 180 °C. Red phosphorescence-based OLED devices were fabricated to analyze the device performances compared to Spiro-NPB and NPB as reference hole transporting materials. Devices consist of hole transporting material as HTM 1B showed better maximum current and power efficiencies of 16.16 cd/A and 11.17 lm/W, at the same time it revealed an improved external quantum efficiency of 13.64%. This efficiency is considerably higher than that of Spiro-NPB and NPB-based reference devices.

  2. Study of the electroluminescence of highly stereoregular poly(N-pentenyl-carbazole) for blue and white OLEDs

    Science.gov (United States)

    Liguori, R.; Botta, A.; Pragliola, S.; Rubino, A.; Venditto, V.; Velardo, A.; Aprano, S.; Maglione, M. G.; Prontera, C. T.; De Girolamo Del Mauro, A.; Fasolino, T.; Minarini, C.

    2017-06-01

    The electroluminescence (EL) of isotactic and syndiotactic poly(N-pentenyl-carbazole) (PPK), achieved by coordination polymerization, is studied in order to investigate the interrelation between the polymer tacticity and their physical-chemical properties. The use of these polymers in organic light-emitting diode (OLED) fabrication is also explored. Thermal and x-ray diffraction analyses of PPKs show that the isotactic stereoisomer is semicrystalline, whereas the syndiotactic one is amorphous. Optical analysis of both stereoisomers, carried out on film samples, reveals the presence of two different excimers: ‘sandwich-like’ and ‘partially overlapping’. Nevertheless, the emission intensity ratio between ‘sandwich-like’ and ‘partially overlapping’ excimers is higher in the isotactic than in the syndiotactic stereoisomer. Using the synthesized polymers as OLED emitting layers, the influence of the polymer tacticity on the EL properties of the device is highlighted. In detail, while blue OLEDs are obtained by using the syndiotactic stereoisomer, OLEDs with a multilayer structure fabricated with the isotactic stereoisomer emit white light. The contribution of three different emissions (fluorescence, phosphorescence and electromer emissions) with comparable intensities to the detected white light is discussed.

  3. Final Report DOE SSL Grant (No. DE-EE0006673) Advanced Light Extraction Structure for OLED Lighting

    Energy Technology Data Exchange (ETDEWEB)

    Cooper, Gregory [Pixelligent Technologies LLC, Baltimore, MD (United States); Monickam, Selina [Pixelligent Technologies LLC, Baltimore, MD (United States)

    2017-08-29

    The innovation proposed in this grant is to demonstrate a novel internal light extraction (ILE) design that can maximize the energy efficiency of Organic Light Emitting Diode (OLED) lighting devices without negatively impacting the device voltage, efficacy or angular color dependences. Even though, OLEDs have unique features compared to its inorganic counterparts, LEDs, in terms of technology development and market readiness levels, it still lags LEDs by several years. The main challenges as identified in the National Research Council’s 2013 Assessment on Solid State Lighting, are the cost of the materials and the low light extraction efficacy [1]. Improving the light extraction will improve both the $/Klm and lm/W, two important metrics DOE uses to measure the cost effectiveness of a light source.

  4. The Electroluminescence Mechanism of Solution-Processed TADF Emitter 4CzIPN Doped OLEDs Investigated by Transient Measurements

    Directory of Open Access Journals (Sweden)

    Peng Wang

    2016-10-01

    Full Text Available High efficiency, solution-processed, organic light emitting devices (OLEDs, using a thermally-activated delayed fluorescent (TADF emitter, 1,2,3,5-tetrakis(carbazol-9-yl-4,6-dicyanobenzene (4CzIPN, are fabricated, and the transient electroluminescence (EL decay of the device with a structure of [ITO/PEDOT: PSS/4CzIPN 5 wt % doped 4,40-N,N0-dicarbazolylbiphenyl(CBP/bis-4,6-(3,5-di-4-pyridylphenyl-2-methylpyrimidine (B4PyMPM/lithium fluoride (LiF/Al], is systematically studied. The results shed light on the dominant operating mechanism in TADF-based OLEDs. Electroluminescence in the host–guest system is mainly produced from the 4CzIPN emitter, rather than the exciplex host materials.

  5. Nondoped deep blue OLEDs based on Bis-(4-benzenesulfonyl-phenyl)-9-phenyl-9H-carbazoles

    International Nuclear Information System (INIS)

    Huang, Bin; Yin, Zhihui; Ban, Xinxin; Ma, Zhongming; Jiang, Wei; Tian, Wenwen; Yang, Min; Ye, Shanghui; Lin, Baoping; Sun, Yueming

    2016-01-01

    Two bipolar materials based on 9-phenylcarbazole and diphenyl sulfone for nondoped deep blue OLEDs, namely bis-(4-benzenesulfonyl-phenyl)-9-phenyl-9H-carbazoles, have been designed and synthesized by Suzuki coupling reactions. Their thermal, photophysical, and electrochemical properties have been systematically investigated. The nondoped devices using 3,6–bis–(4-benzenesulfonyl-phenyl)-9-phenyl-9H-carbazoles and 2,7-bis-(4-benzenesulfonyl-phenyl)-9-phenyl-9H-carbazoles as the emitters show deep blue emission color with peaks at 424 and 444 nm, and the Commission Internationale de l'Eclairage (CIE) coordinates of (0.177, 0.117) and (0.160, 0.117), respectively. Furthermore, these materials based devices have high color-purity with small width at half-maximum (FWHM) of 65 and 73 nm, respectively. The results provide a novel approach for the design of deep blue emitter for nondoped OLEDs.

  6. RCWA and FDTD modeling of light emission from internally structured OLEDs.

    Science.gov (United States)

    Callens, Michiel Koen; Marsman, Herman; Penninck, Lieven; Peeters, Patrick; de Groot, Harry; ter Meulen, Jan Matthijs; Neyts, Kristiaan

    2014-05-05

    We report on the fabrication and simulation of a green OLED with an Internal Light Extraction (ILE) layer. The optical behavior of these devices is simulated using both Rigorous Coupled Wave Analysis (RCWA) and Finite Difference Time-Domain (FDTD) methods. Results obtained using these two different techniques show excellent agreement and predict the experimental results with good precision. By verifying the validity of both simulation methods on the internal light extraction structure we pave the way to optimization of ILE layers using either of these methods.

  7. Ole Rømer som enevældens administrator

    DEFF Research Database (Denmark)

    Olden-Jørgensen, Sebastian

    2002-01-01

    En gennemgang af Ole Rømers liv med vægt på hans rolle som embedsmand og hans deltagelse eller mangel på samme i det politiske spil.......En gennemgang af Ole Rømers liv med vægt på hans rolle som embedsmand og hans deltagelse eller mangel på samme i det politiske spil....

  8. Seniorforsker Ole Hertel udnævnt til adjungeret professor

    DEFF Research Database (Denmark)

    Pedersen, Jens Christian

    2009-01-01

    Sektionsleder og seniorforsker Ole Hertel, Danmarks Miljøundersøgelser (DMU) ved Aarhus Universitet, er udnævnt til adjungeret professor ved Institut for Miljø, Samfund og Rumlig Forandring på Roskilde Universitet.......Sektionsleder og seniorforsker Ole Hertel, Danmarks Miljøundersøgelser (DMU) ved Aarhus Universitet, er udnævnt til adjungeret professor ved Institut for Miljø, Samfund og Rumlig Forandring på Roskilde Universitet....

  9. An examination of OLED display application to military equipment

    Science.gov (United States)

    Thomas, J.; Lorimer, S.

    2010-04-01

    OLED display technology has developed sufficiently to support small format commercial applications such as cell-phone main display functions. Revenues seem sufficient to finance both performance improvements and to develop new applications. The situation signifies the possibility that OLED technology is on the threshold of credibility for military applications. This paper will examine both performance and some possible applications for the military ground mobile environment, identifying the advantages and disadvantages of this promising new technology.

  10. Efficient blue and green phosphorescent OLEDs with host material containing electronically isolated carbazolyl fragments

    Science.gov (United States)

    Grigalevicius, Saulius; Tavgeniene, Daiva; Krucaite, Gintare; Blazevicius, Dovydas; Griniene, Raimonda; Lai, Yi-Ning; Chiu, Hao-Hsuan; Chang, Chih-Hao

    2018-05-01

    Dry process-able host materials are well suited to realize high performance phosphorescent organic light-emitting diodes (OLED) with precise deposition of organic layers. We demonstrate in this study high efficiency green and blue phosphorescent OLED devices by employing 3-[bis(9-ethylcarbazol-3-yl)methyl]-9-hexylcarbazole based host material. By doping a typical green emitter of fac tris(2-phenylpyridine)iridium (Ir (ppy)3) in the compound the resultant dry-processed green device exhibited superior performance with low turn on voltage of 3.0 V and with peak efficiencies of 11.4%, 39.9 cd/A and 41.8 lm/W. When blue emitter of bis [2-(4,6-difluorophenyl)pyridinato-C2,N](picolinato)iridium (III) was used, the resultant blue device showed turn on voltage of 2.9 V and peak efficiencies of 9.4%, 21.4 cd/A and 21.7 lm/W. The high efficiencies may be attributed to the host possessing high triplet energy level, effective host-to-guest energy transfer and effective carrier injection balance.

  11. Pure white OLED based on an organic small molecule: 2,6-Di(1H-benzo[d]imidazol-2-yl)pyridine

    Science.gov (United States)

    Liu, Jian

    2015-10-01

    2,6-Di(1H-benzo[d]imidazol-2-yl)pyridine (DBIP) was synthesized. The single-crystal structure of DBIP was resolved. DBIP-based OLED was fabricated. The electroluminescence for the device corresponds to a pure white emission. In addition, thermal stability, UV-vis, photoluminescence and electrochemical behaviors of DBIP were investigated as well.

  12. Vacuum Deposited Organic Light Emitting Devices on Flexible Substrates

    National Research Council Canada - National Science Library

    Forrest, Stephen

    2002-01-01

    The objective of this eight year program was to demonstrate both passive and active matrix, flexible, small scale displays based on small molecular weight organic light emitting device (OLED) technology...

  13. Improved stability of OLEDs with mild oxygen plasma treated PEDOT:PSS

    International Nuclear Information System (INIS)

    Zhou Yunfei; Yuan Yongbo; Cao Lingfang; Zhang Jie; Pang Hongqi; Lian Jiarong; Zhou Xiang

    2007-01-01

    We demonstrate improved stability of OLEDs with mild oxygen plasma-treated poly (3,4-ethylenedioxythiophene) doped with poly (styrenesulfonate) (PEDOT:PSS) as anode buffer layer. The devices with treated PEDOT:PSS layer exhibited dramatically enhanced lifetime by a factor of 9 compared to the control devices. We investigated the substantial changes in surface morphology of PEDOT:PSS layer after the mild oxygen plasma treatment by scanning electron microscopy and atomic force microscopy. We found that the appropriate treatment can form uniformly distributed nano scaled hillocks/islands on the surface of PEDOT:PSS layer, which possibly result in improved contact to hole transport layer and thus enhanced lifetime of the devices

  14. High ambient contrast ratio OLED and QLED without a circular polarizer

    International Nuclear Information System (INIS)

    Tan, Guanjun; Zhu, Ruidong; Luo, Zhenyue; Wu, Shin-Tson; Tsai, Yi-Shou; Lee, Kuo-Chang; Lee, Yuh-Zheng

    2016-01-01

    A high ambient contrast ratio display device using a transparent organic light emitting diode (OLED) or transparent quantum-dot light-emitting diode (QLED) with embedded multilayered structure and absorber is proposed and its performance is simulated. With the help of multilayered structure, the device structure allows almost all ambient light to get through the display device and be absorbed by the absorber. Because the reflected ambient light is greatly reduced, the ambient contrast ratio of the display system is improved significantly. Meanwhile, the multilayered structure helps to lower the effective refractive index, which in turn improves the out-coupling efficiency of the display system. Potential applications for sunlight readable flexible and rollable displays are emphasized. (paper)

  15. de los hoteles españoles

    Directory of Open Access Journals (Sweden)

    Enrique Claver Cortés

    2007-01-01

    Full Text Available Los hoteles necesitan cada vez más información para su correcta gestión y para maximizar su desempeño o éxito empresarial. De esta forma, en este estudio se analizan una serie de variables estratégicas clave que influyen directamente sobre el desempeño hotelero. Estas variables son el tamaño, el tipo de gestión y la categoría de los hoteles. En este trabajo, empleando la teoría de los grupos estratégicos, se han agrupado los hoteles españoles de entre 3 a 5 estrellas en función de cada una de estas variables estratégicas con el objetivo de determinar si influyen significativamente sobre el desempeño hotelero y en qué sentido. Entre los resultados que se han obtenido destacan el hecho de que a mayor tamaño y categoría, mayor es el desempeño que alcanzan los hoteles. Así mismo, los hoteles que pertenecen a cadenas alcanzan niveles de desempeño mayores que los independientes. Por lo tanto, de esta investigación se deducen importantes implicaciones para la dirección hotelera.

  16. Highly efficient tandem OLED based on C{sub 60}/rubrene: MoO{sub 3} as charge generation layer and LiF/Al as electron injection layer

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yang [School of Materials Science and Engineering, Tianjin University of Technology, Tianjin 300384 (China); Key Laboratory of Display Materials and Photoelectric Devices, Ministry of Education, Tianjin 300384 (China); Tianjin Key Laboratory of Photoelectric Materials and Devices, Tianjin 300384 (China); College of Science, Tianjin University of Technology, Tianjin 300384 (China); Wu, Xiaoming, E-mail: wxm@tjut.edu.cn [School of Materials Science and Engineering, Tianjin University of Technology, Tianjin 300384 (China); Key Laboratory of Display Materials and Photoelectric Devices, Ministry of Education, Tianjin 300384 (China); Tianjin Key Laboratory of Photoelectric Materials and Devices, Tianjin 300384 (China); Xiao, Zhihui; Gao, Jian; Zhang, Juan; Rui, Hongsong; Lin, Xin; Zhang, Nan; Hua, Yulin [School of Materials Science and Engineering, Tianjin University of Technology, Tianjin 300384 (China); Key Laboratory of Display Materials and Photoelectric Devices, Ministry of Education, Tianjin 300384 (China); Tianjin Key Laboratory of Photoelectric Materials and Devices, Tianjin 300384 (China); Yin, Shougen, E-mail: sgyin@tjut.edu.cn [School of Materials Science and Engineering, Tianjin University of Technology, Tianjin 300384 (China); Key Laboratory of Display Materials and Photoelectric Devices, Ministry of Education, Tianjin 300384 (China); Tianjin Key Laboratory of Photoelectric Materials and Devices, Tianjin 300384 (China)

    2017-08-15

    Highlights: • Highly efficient blue fluorescent tandem OLEDs are fabricated. • The optimal tandem OLED consists of C{sub 60}/rubrene: MoO{sub 3} as a CGL and LiF/Al as an EIL. • Current efficiency and power efficiency of optimal tandem OLED is markedly enhanced. • The turn-on and driving voltages of optimal tandem OLED is obviously reduced. - Abstract: Tandem organic light-emitting diodes (OLEDs) have received much attention in solid-state lighting due to their high current efficiency, long lifetime and excellent stability. The highly efficient blue fluorescent tandem OLEDs based on the charge generation layer (CGL) of C{sub 60}/rubrene: MoO{sub 3} and the electron injection layer (EIL) of LiF/Al were fabricated. The ultra-thin Al layer in EIL was introduced to further increase electron injection from CGL to the emission unit. We found that the maximal current efficiency and power efficiency of optimal tandem device can reach to 43.1 cd/A and 15.1 lm/W, respectively, which are approximately 2.8 and 1.9 times compared with those of single-emissive-unit device. Moreover, compared with the traditional tandem device, the driving voltage of the optimal device is reduced by 6 V, and the turn-on voltage is reduced by 2.4 V. We analyzed the mechanism and characterization of these tandem devices. The effective charge separation and transport of C{sub 60}/rubrene: MoO{sub 3}, and excellent electron injection ability of ultra-thin Al layer are the main factors for the remarkable enhancement in both current efficiency and power efficiency of tandem OLEDs.

  17. Electronic device and method of manufacturing an electronic device

    NARCIS (Netherlands)

    2009-01-01

    An electronic device comprising at least one die stack having at least a first die (D1) comprising a first array of light emitting units (OLED) for emitting light, a second layer (D2) comprising a second array of via holes (VH) and a third die (D3) comprising a third array of light detecting units

  18. Polymers Containing Diphenylvinyl-Substituted Indole Rings as Charge-Transporting Materials for OLEDs

    Science.gov (United States)

    Grigalevicius, S.; Zostautiene, R.; Sipaviciute, D.; Stulpinaite, B.; Volyniuk, D.; Grazulevicius, J. V.; Liu, L.; Xie, Z.; Zhang, B.

    2016-02-01

    Monomers and polymers containing electronically isolated diphenylvinyl-substituted indole rings were synthesized and characterized by nuclear magnetic resonance (NMR) and mass spectroscopies as well as by gel permeation chromatography. The polymers represent amorphous materials with glass transition temperatures of 91-109°C and thermal decomposition starting above 307°C. Electron photoemission spectra of thin films of the synthesized polymers revealed ionization potentials of 5.54-5.58 eV. The synthesized polymers were tested as hole-transporting materials in simple electroluminescent organic light-emitting diode (OLED) devices with tris(quinolin-8-olato)aluminium (Alq3) as an emitter as well as an electron-transporting layer. A green OLED device containing a hole-transporting layer of poly[1-(2,3-epithiopropyl)-2-methyl-3-(2,2-diphenylvinyl)índole] exhibited the best overall performance with a driving voltage of 4.0 V, maximum photometric efficiency of 2.8 cd/A and maximum brightness of about 4200 cd/m2.

  19. Architectural prototyping

    DEFF Research Database (Denmark)

    Bardram, Jakob Eyvind; Christensen, Henrik Bærbak; Hansen, Klaus Marius

    2004-01-01

    A major part of software architecture design is learning how specific architectural designs balance the concerns of stakeholders. We explore the notion of "architectural prototypes", correspondingly architectural prototyping, as a means of using executable prototypes to investigate stakeholders...

  20. Balance the Carrier Mobility To Achieve High Performance Exciplex OLED Using a Triazine-Based Acceptor.

    Science.gov (United States)

    Hung, Wen-Yi; Chiang, Pin-Yi; Lin, Shih-Wei; Tang, Wei-Chieh; Chen, Yi-Ting; Liu, Shih-Hung; Chou, Pi-Tai; Hung, Yi-Tzu; Wong, Ken-Tsung

    2016-02-01

    A star-shaped 1,3,5-triazine/cyano hybrid molecule CN-T2T was designed and synthesized as a new electron acceptor for efficient exciplex-based OLED emitter by mixing with a suitable electron donor (Tris-PCz). The CN-T2T/Tris-PCz exciplex emission shows a high ΦPL of 0.53 and a small ΔET-S = -0.59 kcal/mol, affording intrinsically efficient fluorescence and highly efficient exciton up-conversion. The large energy level offsets between Tris-PCz and CN-T2T and the balanced hole and electron mobility of Tris-PCz and CN-T2T, respectively, ensuring sufficient carrier density accumulated in the interface for efficient generation of exciplex excitons. Employing a facile device structure composed as ITO/4% ReO3:Tris-PCz (60 nm)/Tris-PCz (15 nm)/Tris-PCz:CN-T2T(1:1) (25 nm)/CN-T2T (50 nm)/Liq (0.5 nm)/Al (100 nm), in which the electron-hole capture is efficient without additional carrier injection barrier from donor (or acceptor) molecule and carriers mobilities are balanced in the emitting layer, leads to a highly efficient green exciplex OLED with external quantum efficiency (EQE) of 11.9%. The obtained EQE is 18% higher than that of a comparison device using an exciplex exhibiting a comparable ΦPL (0.50), in which TCTA shows similar energy levels but higher hole mobility as compared with Tris-PCz. Our results clearly indicate the significance of mobility balance in governing the efficiency of exciplex-based OLED. Exploiting the Tris-PCz:CN-T2T exciplex as the host, we further demonstrated highly efficient yellow and red fluorescent OLEDs by doping 1 wt % Rubrene and DCJTB as emitter, achieving high EQE of 6.9 and 9.7%, respectively.

  1. Organic solution-processible electroluminescent molecular glasses for non-doped standard red OLEDs with electrically stable chromaticity

    Energy Technology Data Exchange (ETDEWEB)

    Bi, Xiaoman; Zuo, Weiwei; Liu, Yingliang, E-mail: liuylxn@sohu.com; Zhang, Zhenru; Zeng, Cen; Xu, Shengang; Cao, Shaokui, E-mail: caoshaokui@zzu.edu.cn

    2015-10-15

    Highlights: • The D–A–D electroluminescent molecular glasses are synthesized. • Non-doped red electroluminescent film is fabricated by spin-coating. • Red OLED shows stable wavelength, luminous efficiency and chromaticity. • CIE1931 coordinate is in accord with standard red light in PAL system. - Abstract: Organic light-emitting molecular glasses (OEMGs) are synthesized through the introduction of nonplanar donor and branched aliphatic chain into electroluminescent emitters. The target OEMGs are characterized by {sup 1}H NMR, {sup 13}C NMR, IR, UV–vis and fluorescent spectra as well as elemental analysis, TG and DSC. The results indicated that the optical, electrochemical and electroluminescent properties of OEMGs are adjusted successfully by the replacement of electron-donating group. The non-doped OLED device with a standard red electroluminescent emission is achieved by spin-coating the THF solution of OEMG with a triphenylamine moiety. This non-doped red OLED device takes on an electrically stable electroluminescent performance, including the stable maximum electroluminescent wavelength of 640 nm, the stable luminous efficiency of 2.4 cd/A and the stable CIE1931 coordinate of (x, y) = (0.64, 0.35), which is basically in accord with the CIE1931 coordinate (x, y) = (0.64, 0.33) of standard red light in PAL system.

  2. Architecture on Architecture

    DEFF Research Database (Denmark)

    Olesen, Karen

    2016-01-01

    that is not scientific or academic but is more like a latent body of data that we find embedded in existing works of architecture. This information, it is argued, is not limited by the historical context of the work. It can be thought of as a virtual capacity – a reservoir of spatial configurations that can...... correlation between the study of existing architectures and the training of competences to design for present-day realities.......This paper will discuss the challenges faced by architectural education today. It takes as its starting point the double commitment of any school of architecture: on the one hand the task of preserving the particular knowledge that belongs to the discipline of architecture, and on the other hand...

  3. Degradation of phosphorescent blue organic light-emitting diodes (OLED); Degradation der phosphoreszenten blauen organischen Leuchtdioden

    Energy Technology Data Exchange (ETDEWEB)

    Chiu, Chien-Shu

    2011-07-01

    Phosphorescent organic materials harvest singlet and triplet excitons through inter-system crossing and improve the efficiency of organic light-emitting diodes (OLEDs). This improvement increases the potential of OLEDs, particularly white phosphorescent OLEDs (PHOLEDs), for lighting application. Although much progress has been made in the development of white PHOLEDs, the lifetime of phosphorescent emitters, especially the blue emitter, still needs to be improved. This thesis discusses the developments of blue PHOLEDs and investigations of degradation mechanisms. For development of blue PHOLEDs, two phosphorescent blue emitters were investigated: commercially available FIrpic and B1 provided by BASF. By varying the matrix and blocker materials, diode efficiency and lifetime have been investigated and improved. Blue PHOLEDs with emitter B1 show better efficiency and lifetime than devices with FIrpic. From lifetime measurement with constant DC current density, intrinsic degradation including luminance loss and voltage increase on both FIrpic and B1 PHOLEDs was observed. Photoluminescence measurement shows degradation in the emitting layers. To investigate the degradation of emitter layers, single-carrier devices with emitter systems or pure matrix materials were fabricated. Degradation on these devices was investigated by applying constant DC current, UV-irradiation and combination of both. We found that due to excited states (excitons), FIrpic molecules become unstable and polarons would enhance the degradation of FIrpic during DC operation and UV-excitation. To investigate the impact the exciton formation and exciton decay have on the degradation of FIrpic molecules, red phosphorescent emitter Ir(MDQ){sub 2}(acac) was doped in blue emitter layer TCTA:20% FIrpic. The doping concentration of Ir(MDQ){sub 2}(acac) was much lower than FIrpic to ensure that most of the exciton formation occurred on FIrpic molecules. Lower triplet energy of Ir(MDQ){sub 2}(acac) molecules

  4. Evaluation of OLED and edge-lit LED lighting panels

    Science.gov (United States)

    Mou, Xi; Narendran, Nadarajah; Zhu, Yiting; Freyssinier, Jean Paul

    2016-09-01

    Solid-state lighting (SSL) offers a new technology platform for lighting designers and end-users to illuminate spaces with low energy demand. Two types of SSL sources include organic light-emitting diodes (OLEDs) and light-emitting diodes (LEDs). OLED is an area light source, and its primary competing technology is the edge-lit LED panel. Generally, both of these technologies are considered similar in shape and appearance, but there is little understanding of how people perceive discomfort glare from large area light sources. The objective of this study was to evaluate discomfort glare for the two lighting technologies under similar operating conditions by gathering observers' reactions. The human factors study results showed no statistically significant difference in human response to discomfort glare between OLED and edge-lit LED panels when the two light sources produced the same lighting stimulus. This means both technologies appeared equally glary beyond a certain luminance.

  5. Multispectral surface plasmon resonance approach for ultra-thin silver layer characterization: Application to top-emitting OLED cathode

    Science.gov (United States)

    Taverne, S.; Caron, B.; Gétin, S.; Lartigue, O.; Lopez, C.; Meunier-Della-Gatta, S.; Gorge, V.; Reymermier, M.; Racine, B.; Maindron, T.; Quesnel, E.

    2018-01-01

    While dielectric/metal/dielectric (DMD) multilayer thin films have raised considerable interest as transparent and conductive electrodes in various optoelectronic devices, the knowledge of optical characteristics of thin metallic layers integrated in such structures is still rather approximate. The multispectral surface plasmon resonance characterization approach described in this work precisely aims at providing a rigorous methodology able to accurately determine the optical constants of ultra-thin metallic films. As a practical example, the refractive index and extinction dispersion curves of 8 to 25 nm-thick silver layers have been investigated. As a result, their extreme dependence on the layer thickness is highlighted, in particular in a thickness range close to the critical threshold value (˜10 nm) where the silver film becomes continuous and its electrical conductance/optical transmittance ratio particularly interesting. To check the validity of the revisited Ag layers constant dispersion curves deduced from this study, they were introduced into a commercial optical model software to simulate the behavior of various optoelectronic building blocks from the simplest ones (DMD electrodes) to much more complex structures [full organic light emitting device (OLED) stacks]. As a result, a much better prediction of the emission spectrum profile as well as the angular emission pattern of top-emitting OLEDs is obtained. On this basis, it is also shown how a redesign of the top encapsulation thin film of OLEDs is necessary to better take benefit from the advanced DMD electrode. These results should particularly interest the micro-OLED display field where bright and directive single color pixel emission is required.

  6. Enhancing User Experiences of Mobile-Based Augmented Reality via Spatial Augmented Reality: Designs and Architectures of Projector-Camera Devices

    Directory of Open Access Journals (Sweden)

    Thitirat Siriborvornratanakul

    2018-01-01

    Full Text Available As smartphones, tablet computers, and other mobile devices have continued to dominate our digital world ecosystem, there are many industries using mobile or wearable devices to perform Augmented Reality (AR functions in their workplaces in order to increase productivity and decrease unnecessary workloads. Mobile-based AR can basically be divided into three main types: phone-based AR, wearable AR, and projector-based AR. Among these, projector-based AR or Spatial Augmented Reality (SAR is the most immature and least recognized type of AR for end users. This is because there are a small number of commercial products providing projector-based AR functionalities in a mobile manner. Also, prices of mobile projectors are still relatively high. Moreover, there are still many technical problems regarding projector-based AR that have been left unsolved. Nevertheless, it is projector-based AR that has potential to solve a fundamental problem shared by most mobile-based AR systems. Also the always-visible nature of projector-based AR is one good answer for solving current user experience issues of phone-based AR and wearable AR systems. Hence, in this paper, we analyze what are the user experience issues and technical issues regarding common mobile-based AR systems, recently widespread phone-based AR systems, and rising wearable AR systems. Then for each issue, we propose and explain a new solution of how using projector-based AR can solve the problems and/or help enhance its user experiences. Our proposed framework includes hardware designs and architectures as well as a software computing paradigm towards mobile projector-based AR systems. The proposed design is evaluated by three experts using qualitative and semiquantitative research approaches.

  7. Temperature dependence of electron mobility, electroluminescence and photoluminescence of Alq{sub 3} in OLED

    Energy Technology Data Exchange (ETDEWEB)

    Mu Haichuan; White, Dan; Sharpton, Buck [Office of Electronic Miniaturization, University of Alaska at Fairbanks, AK 99701 (United States); Klotzkin, David [Department of Electrical and Computer Engineering and Computer Sciences, University of Cincinnati, Cincinnati, OH 45221 (United States); De Silva, Ajith; Wagner, Hans Peter [Department of Physics, University of Cincinnati, Cincinnati, OH 45221 (United States)], E-mail: fnhm@uaf.edu

    2008-12-07

    The correlation of electroluminescence (EL), photoluminescence (PL) and electron mobility were investigated over temperature from 60 to 300 K in small-molecule organic light emitting diode (OLED) structures. The devices consisted of ITO/PEDOT(50 nm)/TPD(50 nm)/Alq{sub 3}(60 nm)/LiF(1 nm)/Al(90 nm), and were fabricated with high-vacuum sublimation/evaporation in a cross-linked configuration. Electron mobility was measured using an ac analysis of the device optical modulation characteristics, while PL and EL were measured by measuring optical power out at fixed pump power of 1 mW, and analysis of dc brightness-voltage (L-V) characteristics, respectively. PL intensity and mobility had a clear maximum at around 220 K, while EL efficiency was constant below 220 K and decrease monotonically above. The reason for the temperature dependent EL, PL and electron mobility behaviour will be discussed.

  8. Transient electroluminescence on pristine and degraded phosphorescent blue OLEDs

    Science.gov (United States)

    Niu, Quan; Blom, Paul W. M.; May, Falk; Heimel, Paul; Zhang, Minlu; Eickhoff, Christian; Heinemeyer, Ute; Lennartz, Christian; Crǎciun, N. Irina

    2017-11-01

    In state-of-the-art blue phosphorescent organic light-emitting diode (PHOLED) device architectures, electrons and holes are injected into the emissive layer, where they are carried by the emitting and hole transporting units, respectively. Using transient electroluminescence measurements, we disentangle the contribution of the electrons and holes on the transport and efficiency of both pristine and degraded PHOLEDs. By varying the concentration of hole transporting units, we show that for pristine PHOLEDs, the transport is electron dominated. Furthermore, degradation of the PHOLEDs upon electrical aging is not related to the hole transport but is governed by a decrease in the electron transport due to the formation of electron traps.

  9. Ole Rømer som enevældens administrator

    DEFF Research Database (Denmark)

    Olden-Jørgensen, Sebastian

    2004-01-01

    En biografisk skitse af Ole Rømers virke med vægt på hans rolle som embedsmand og rådgiver for Christian V. Hans virke analyseres på baggrund af en ny forståelse for den tidlige enevældes politiske kultur.......En biografisk skitse af Ole Rømers virke med vægt på hans rolle som embedsmand og rådgiver for Christian V. Hans virke analyseres på baggrund af en ny forståelse for den tidlige enevældes politiske kultur....

  10. Ole Bjørn Kraft 1893-1980

    DEFF Research Database (Denmark)

    Skov, Christian Houlberg

    2010-01-01

    Ole Bjørn Kraft (1893-1980) var en central konservativ politiker i årene før og efter anden verdenskrig. Han markerede sig som udpræget idépolitiker og opnåede ad flere omgange at blive minister.......Ole Bjørn Kraft (1893-1980) var en central konservativ politiker i årene før og efter anden verdenskrig. Han markerede sig som udpræget idépolitiker og opnåede ad flere omgange at blive minister....

  11. Active-matrix OLED (AMOLED) microdisplay for augmented-reality applications with improved color space

    OpenAIRE

    Thomschke, Michael; Fehse, Karsten; Richter, Bernd; Wartenberg, Philipp; Pfeifer, Richard; Vogel, Uwe

    2013-01-01

    Our contribution describes the optimization of OLED microdisplays to increase the color gamut and to reduce the OLED complexity. We show that these improvements can be reached by a 3-color RGB-white OLED approach that features a single layer multicolor emitting zone, respectively.

  12. High Efficancy Integrated Under-Cabinet Phosphorescent OLED

    Energy Technology Data Exchange (ETDEWEB)

    Michael Hack

    2001-10-31

    In this two year program Universal Display Corporation (UDC) together with the University of Michigan, Teknokon, developed and delivered an energy efficient phosphorescent OLED under cabinet illumination system. Specifically the UDC team goal was in 2011 to deliver five (5) Beta level OLED under cabinet lighting fixtures each consisting of five 6-inch x 6-inch OLED lighting panels, delivering over 420 lumens, at an overall system efficacy of >60 lm/W, a CRI of >85, and a projected lifetime to 70% of initial luminance to exceed 20,000 hours. During the course of this program, the Team pursued the commercialization of these OLED based under cabinet lighting fixtures, to enable the launch of commercial OLED lighting products. The UDC team was ideally suited to develop these novel and efficient solid state lighting fixtures, having both the technical experience and commercial distribution mechanisms to leverage work performed under this contract. UDC's business strategy is to non-exclusively license its PHOLED technology to lighting manufacturers, and also supply them with our proprietary PHOLED materials. UDC is currently working with several licensees who are manufacturing OLED lighting panels using our technology. During this 2 year program, we further developed our high efficiency white Phosphorescent OLEDs from the first milestone, achieving a 80 lm/W single pixel to the final milestone, achieving an under-cabinet PHOLED lighting system that operates at 56 lm/W at 420 lumens. Each luminaire was comprised of ten 15cm x 7.5cm lighting modules mounted in outcoupling enhancement lenses and a control module. The lamps modules are connected together using either plugs or wires with plugs on each end, allowing for unlimited configurations. The lamps are driven by an OLED driver mounted in an enclosure which includes the AC plug. As a result of advancements gained under this program, the path to move OLED lighting panels from development into manufacturing has been

  13. Highly luminescent pure-red-emitting fluorinated β-diketonate europium(III) complex for full solution-processed OLEDs

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Joao P. [CEMDRX, Physics Department, Universidade de Coimbra, Rua Larga, Coimbra P-3004-516 (Portugal); Serviço de Medicina Nuclear, SESARAM E.P.E., Avenida Luís de Camões 57, Funchal 9004-514, Madeira (Portugal); Martín-Ramos, Pablo [CEMDRX, Physics Department, Universidade de Coimbra, Rua Larga, Coimbra P-3004-516 (Portugal); Higher Technical School of Telecommunications Engineering, Universidad de Valladolid, Campus Miguel Delibes, Paseo Belén 15, Valladolid 47011 (Spain); Coya, Carmen, E-mail: carmen.coya@urjc.es [Escuela Superior de Ciencias Experimentales y Tecnología (ESCET), Universidad Rey Juan Carlos, Madrid 28933 (Spain); Silva, Manuela Ramos [CEMDRX, Physics Department, Universidade de Coimbra, Rua Larga, Coimbra P-3004-516 (Portugal); Eusebio, M. Ermelinda S. [Chemistry Department, Faculdade de Ciências e Tecnologia, Universidade de Coimbra, Coimbra P-3004-535 (Portugal); Andrés, Alicia de [Instituto de Ciencia de Materiales de Madrid, Consejo Superior de Investigaciones Científicas (CSIC), Cantoblanco, Madrid 28049 (Spain); Álvarez, Ángel L. [Escuela Superior de Ciencias Experimentales y Tecnología (ESCET), Universidad Rey Juan Carlos, Madrid 28933 (Spain); Martín-Gil, Jesús [Advanced Materials Laboratory, ETSIIAA, Universidad de Valladolid, Avenida de Madrid 44, Palencia 34004 (Spain)

    2015-03-15

    Current manufacturing technologies for OLEDs involve the use of expensive high vacuum techniques and call for thermal stability requirements which are not fulfilled by many materials. These problems disappear when the OLED films are deposited directly from solution. In this study, we have designed, synthesized and characterized a novel octacoordinated complex, Tris(1-(4-chlorophenyl)-4,4,4-trifluoro-1, 3-butanedionate)mono(bathophenanthroline) europium(III), to be used as a “complex-only” emissive layer in wet-processed OLEDs. Upon excitation in the UV region, very efficient energy transfer from the ligands to Eu{sup 3+} takes place, giving rise to intense red emission with very high monochromaticity (R=19), both in powder and as a thin film. The decay times of 754 µs (powder) and 620 µs (thin film) are comparable to those of the most efficient Eu{sup 3+} β-diketonate complexes reported to date. The same energy transfer leading to saturated red and narrow emission is also observed in the OLED device (glass/ITO/PEDOT:PSS/[Eu(cbtfa){sub 3}(bath)]/Ca/Al) when biased at >5.2 V. Its high quantum efficiency (∼60%), good thermal stability up to 200 °C and adequate thin film forming properties make this material a promising chromophore for cost-effective OLEDs. - Highlights: • A highly fluorinated europium(III) octacoordinated complex, [Eu(cbtfa)3(bath)], has been synthesized and its structure elucidated by single crystal X-ray diffraction. • The chosen coordination environment is well-suited for sensitizing the luminescence of the Eu{sup 3+} ion, achieving very efficient energy transfer from the organic ligands (excited in the UV region) to the rare earth ion, leading to highly efficient (Q∼60% in crystalline powder and Q∼50% in thin film) and saturated red photoluminescence. • The material has also been integrated into a single active layer, full solution-processed OLED, with ITO/PEDOT:PSS/[Eu(cbtfa)3(bath)]/ Ca/Al structure.

  14. Novel Low Cost Organic Vapor Jet Printing of Striped High Efficiency Phosphorescent OLEDs for White Lighting

    Energy Technology Data Exchange (ETDEWEB)

    Mike Hack

    2008-12-31

    In this program, Universal Display Corporation and University of Michigan proposed to integrate three innovative concepts to meet the DOE's Solid State Lighting (SSL) goals: (1) high-efficiency phosphorescent organic light emitting device (PHOLED{trademark}) technology, (2) a white lighting design that is based on a series of red, green and blue OLED stripes, and (3) the use of a novel cost-effective, high rate, mask-less deposition process called organic vapor jet printing (OVJP). Our PHOLED technology offers up to four-times higher power efficiency than other OLED approaches for general lighting. We believe that one of the most promising approaches to maximizing the efficiency of OLED lighting sources is to produce stripes of the three primary colors at such a pitch (200-500 {mu}m) that they appear as a uniform white light to an observer greater than 1 meter (m) away from the illumination source. Earlier work from a SBIR Phase 1 entitled 'White Illumination Sources Using Striped Phosphorescent OLEDs' suggests that stripe widths of less than 500 {mu}m appear uniform from a distance of 1m without the need for an external diffuser. In this program, we intend to combine continued advances in this PHOLED technology with the striped RGB lighting design to demonstrate a high-efficiency, white lighting source. Using this background technology, the team has focused on developing and demonstrating the novel cost-effective OVJP process to fabricate these high-efficiency white PHOLED light sources. Because this groundbreaking OVJP process is a direct printing approach that enables the OLED stripes to be printed without a shadow mask, OVJP offers very high material utilization and high throughput without the costs and wastage associated with a shadow mask (i.e. the waste of material that deposits on the shadow mask itself). As a direct printing technique, OVJP also has the potential to offer ultra-high deposition rates (> 1,000 Angstroms/second) for any size or

  15. PFE: ZnO hybrid nanocomposites for OLED applications: Fabrication and photophysical properties

    Energy Technology Data Exchange (ETDEWEB)

    Belhaj, M. [Université de Monastir, Faculté des sciences de Monastir, Département de physique, Laboratoire des Interfaces et des Matériaux Avancés, 5019 Monastir (Tunisia); Dridi, C., E-mail: cherif.Dridi@issatso.rnu.tn [Université de Monastir, Faculté des sciences de Monastir, Département de physique, Laboratoire des Interfaces et des Matériaux Avancés, 5019 Monastir (Tunisia); Université de Sousse, Institut Supérieur des Sciences Appliquées et de Technologie de Sousse, Cité Ettafala, 4003 Ibn Khaldoun Sousse (Tunisia); Elhouichet, H. [Centre National de Recherches en Sciences des Matériaux, Laboratoire de physico-Chimie des Matériaux Minéreaux et leurs applications, B.P. 95 Hammam-Lif 2050 (Tunisia)

    2015-01-15

    In this work, ZnO nanoparticles (n-ZnO) and poly (9, 9-dioctyl-fluorenyl-2, 7-yleneethynylene) (PFE): n-ZnO based thin films were spin-coated onto glass substrates. Structural, morphological and optical properties of ZnO, PFE and the PFE: n-ZnO hybrid films with different n-ZnO mass ratios were investigated. n-ZnO films obtained by sol–gel technique are polycrystalline with a hexagonal wurtzite structure. They are also homogenous with an average grain size of about 35 nm. For polymer nanocomposite, the optical properties are closely related to the ZnO content in the mixture. Among the tested active layers, the best performance is observed for that containing 2 wt% of ZnO nanoparticles. - Highlights: • We have analyzed the optical properties of PFE: ZnO nanocomposites . • We have optimized the best PFE: ZnO nanocomposite for the OLED application. • We have demonstrated the feasibility of white OLED devices.

  16. 3,3′-Bicarbazole-Based Host Molecules for Solution-Processed Phosphorescent OLEDs

    Directory of Open Access Journals (Sweden)

    Jungwoon Kim

    2018-04-01

    Full Text Available Solution-processed organic light-emitting diodes (OLEDs are attractive due to their low-cost, large area displays, and lighting features. Small molecules as well as polymers can be used as host materials within the solution-processed emitting layer. Herein, we report two 3,3′-bicarbazole-based host small molecules, which possess a structural isomer relationship. 9,9′-Di-4-n-butylphenyl-9H,9′H-3,3′-bicarbazole (BCz-nBuPh and 9,9′-di-4-t-butylphenyl-9H,9′H-3,3′-bicarbazole (BCz-tBuPh exhibited similar optical properties within solutions but different photoluminescence within films. A solution-processed green phosphorescent OLED with the BCz-tBuPh host exhibited a high maximum current efficiency and power efficiency of 43.1 cd/A and 40.0 lm/W, respectively, compared to the device with the BCz-nBuPh host.

  17. Low temperature transient response and electroluminescence characteristics of OLEDs based on Alq3

    Science.gov (United States)

    Yuan, Chao; Guan, Min; Zhang, Yang; Li, Yiyang; Liu, Shuangjie; Zeng, Yiping

    2017-08-01

    In this work, the organic light-emitting diodes (OLEDs) based on Alq3 are fabricated. In order to make clear the transport mechanism of carriers in organic light-emitting devices at low temperature, detailed electroluminescence transient response and the current-voltage-luminescence (I-V-L) characteristics under different temperatures in those OLEDs are investigated. It founds that the acceleration of brightness increases with increasing temperature is maximum when the temperature is 200 K and it is mainly affected by the electron transport layer (Alq3). The MoO3 injection layer and the electroluminescent layer have great influence on the delay time when the temperature is 200 K. Once the temperature is greater than 250 K, the delay time is mainly affected by the MoO3 injection layer. On the contrary, the fall time is mainly affected by the electroluminescent material. The Vf is the average growth rate of fall time when the temperature increases 1 K which represents the accumulation rate of carriers. The difference between Vf caused by the MoO3 injection layer is 0.52 us/K and caused by the electroluminescent material Ir(ppy)3 is 0.73 us/K.

  18. Color optimization of single emissive white OLEDs via energy transfer between RGB fluorescent dopants

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Nam Ho; Kim, You-Hyun; Yoon, Ju-An; Lee, Sang Youn [Department of Green Energy and Semiconductor Engineering, Hoseo University, Asan (Korea, Republic of); Ryu, Dae Hyun [Department of Information Technology, Hansei University, Gunpo (Korea, Republic of); Wood, Richard [Department of Engineering Physics, McMaster University, Hamilton, Ontario, Canada L8S 4L7 (Canada); Moon, C.-B. [Department of Green Energy and Semiconductor Engineering, Hoseo University, Asan (Korea, Republic of); Kim, Woo Young, E-mail: wykim@hoseo.edu [Department of Green Energy and Semiconductor Engineering, Hoseo University, Asan (Korea, Republic of); Department of Engineering Physics, McMaster University, Hamilton, Ontario, Canada L8S 4L7 (Canada)

    2013-11-15

    The electroluminescent characteristics of white organic light-emitting diodes (WOLEDs) were investigated including single emitting layer (SEL) with an ADN host and dopants; BCzVBi, C545T, and DCJTB for blue, green and red emission, respectively. The structure of the high efficiency WOLED device was; ITO/NPB(700 Å)/ADN: BCzVBi-7%:C545T-0.05%:DCJTB-0.1%(300 Å)/Bphen(300 Å)/Liq(20 Å)/Al(1200 Å) for mixing three primary colors. Luminous efficiency was 9.08 cd/A at 3.5 V and Commission Intenationale de L’eclairage (CIE{sub x,y}) coordinates of white emission was measured as (0.320, 0.338) at 8 V while simulated CIE{sub x,y} coordinates were (0.336, 0.324) via estimation from each dopant's PL spectrum. -- Highlights: • This paper observes single-emissive-layered white OLED using fluorescent dopants. • Electrical and optical properties are analyzed. • Color stability of white OLED is confirmed for new planar light source.

  19. Study on optoelectronic properties of Spiro-CN for developing an efficient OLED

    Science.gov (United States)

    Mishra, Ashok Kumar

    2018-05-01

    There are a class of organic molecules and polymers which exhibit semiconductor behavior because of nearly free conjugate π-electrons. Hopping of these electrons in molecules forms different excited singlet and triplet states named as excitons. Some of these organic molecules can be set to emit photons by triplet-singlet excitonic transition via a process called Thermally Activated Delayed Fluorescence (TADF) which is exploited for designing the Organic Light Emitting diode (OLED.) Spiro-CN (spirobifluorene skeletons) Spiro is one of these reported noble metal-free TADF molecules which offers unique optical and electronic properties arising from the efficient transition and reverse intersystem crossing between the lowest singlet (S) and triplet (T) excited states. Its ability to harvest triplet excitons for fluorescence through facilitated reverse intersystem crossing (T→S) could directly impact their properties and performances, which is attractive for a wide variety of low-cost optoelectronic device. In the present study, the Spiro-CN compounds have been taken up for the investigation of various optoelectronic properties including the thermally activated delayed fluorescence (TADF) by using the Koopmans Method and Density Functional Theory. The present study discusses the utility of the Spiro-CN organic semiconductor as a suitable TADF material essential for developing an efficient Organic Light Emitting Diode (OLED).

  20. White OLED using {beta}-diketones rare earth binuclear complex as emitting layer

    Energy Technology Data Exchange (ETDEWEB)

    Quirino, W.G. [LOEM, Departamento de Fisica, Pontificia Universidade Catolica do Rio de Janeiro, PUC-Rio, P.O.Box 38071, Rio de Janeiro, RJ, CEP 22453-970 (Brazil); Legnani, C. [LOEM, Departamento de Fisica, Pontificia Universidade Catolica do Rio de Janeiro, PUC-Rio, P.O.Box 38071, Rio de Janeiro, RJ, CEP 22453-970 (Brazil); Cremona, M. [LOEM, Departamento de Fisica, Pontificia Universidade Catolica do Rio de Janeiro, PUC-Rio, P.O.Box 38071, Rio de Janeiro, RJ, CEP 22453-970 (Brazil)]. E-mail: cremona@fis.puc-rio.br; Lima, P.P. [Departamento de Quimica Fundamental, Universidade Federal de Pernambuco, UFPE-CCEN, Recife, PE, 50670-901 (Brazil); Junior, S.A. [Departamento de Quimica Fundamental, Universidade Federal de Pernambuco, UFPE-CCEN, Recife, PE, 50670-901 (Brazil); Malta, O.L. [Departamento de Quimica Fundamental, Universidade Federal de Pernambuco, UFPE-CCEN, Recife, PE, 50670-901 (Brazil)

    2006-01-03

    In this work, the fabrication and the characterization of a white triple-layer OLED using a {beta}-diketones binuclear complex [Eu(btfa){sub 3}phenterpyTb(acac){sub 3}] as the emitting layer is reported. The devices were assembled using a heterojunction between three organic molecular materials: the N,N'-bis(naphthalen-1-yl)-N,N'-bis(phenyl)benzidine (NPB) as hole-transporting layer, the {beta}-diketones binuclear complex and the tris(8-hydroxyquinoline aluminum) (Alq{sub 3}) as the electron transporting layer. All the organic layers were sequentially deposited under high vacuum environment by thermal evaporation onto ITO substrates and without breaking vacuum. Continuous electroluminescence emission was obtained varying the applied bias voltage from 10 to 22 V showing a wide emission band from 400 to 700 nm with about 100 cd/m{sup 2} of luminance. The white emission results from a combined action between the binuclear complex, acting as hole blocking and emitting layer, blue from NPB and the typical Alq{sub 3} green emission. The intensity ratio of the peaks is determined by the layer thickness and by the bias voltage applied to the OLED, allowing us to obtain a color tunable light source.

  1. Color optimization of single emissive white OLEDs via energy transfer between RGB fluorescent dopants

    International Nuclear Information System (INIS)

    Kim, Nam Ho; Kim, You-Hyun; Yoon, Ju-An; Lee, Sang Youn; Ryu, Dae Hyun; Wood, Richard; Moon, C.-B.; Kim, Woo Young

    2013-01-01

    The electroluminescent characteristics of white organic light-emitting diodes (WOLEDs) were investigated including single emitting layer (SEL) with an ADN host and dopants; BCzVBi, C545T, and DCJTB for blue, green and red emission, respectively. The structure of the high efficiency WOLED device was; ITO/NPB(700 Å)/ADN: BCzVBi-7%:C545T-0.05%:DCJTB-0.1%(300 Å)/Bphen(300 Å)/Liq(20 Å)/Al(1200 Å) for mixing three primary colors. Luminous efficiency was 9.08 cd/A at 3.5 V and Commission Intenationale de L’eclairage (CIE x,y ) coordinates of white emission was measured as (0.320, 0.338) at 8 V while simulated CIE x,y coordinates were (0.336, 0.324) via estimation from each dopant's PL spectrum. -- Highlights: • This paper observes single-emissive-layered white OLED using fluorescent dopants. • Electrical and optical properties are analyzed. • Color stability of white OLED is confirmed for new planar light source

  2. White OLED using β-diketones rare earth binuclear complex as emitting layer

    International Nuclear Information System (INIS)

    Quirino, W.G.; Legnani, C.; Cremona, M.; Lima, P.P.; Junior, S.A.; Malta, O.L.

    2006-01-01

    In this work, the fabrication and the characterization of a white triple-layer OLED using a β-diketones binuclear complex [Eu(btfa) 3 phenterpyTb(acac) 3 ] as the emitting layer is reported. The devices were assembled using a heterojunction between three organic molecular materials: the N,N'-bis(naphthalen-1-yl)-N,N'-bis(phenyl)benzidine (NPB) as hole-transporting layer, the β-diketones binuclear complex and the tris(8-hydroxyquinoline aluminum) (Alq 3 ) as the electron transporting layer. All the organic layers were sequentially deposited under high vacuum environment by thermal evaporation onto ITO substrates and without breaking vacuum. Continuous electroluminescence emission was obtained varying the applied bias voltage from 10 to 22 V showing a wide emission band from 400 to 700 nm with about 100 cd/m 2 of luminance. The white emission results from a combined action between the binuclear complex, acting as hole blocking and emitting layer, blue from NPB and the typical Alq 3 green emission. The intensity ratio of the peaks is determined by the layer thickness and by the bias voltage applied to the OLED, allowing us to obtain a color tunable light source

  3. PFE: ZnO hybrid nanocomposites for OLED applications: Fabrication and photophysical properties

    International Nuclear Information System (INIS)

    Belhaj, M.; Dridi, C.; Elhouichet, H.

    2015-01-01

    In this work, ZnO nanoparticles (n-ZnO) and poly (9, 9-dioctyl-fluorenyl-2, 7-yleneethynylene) (PFE): n-ZnO based thin films were spin-coated onto glass substrates. Structural, morphological and optical properties of ZnO, PFE and the PFE: n-ZnO hybrid films with different n-ZnO mass ratios were investigated. n-ZnO films obtained by sol–gel technique are polycrystalline with a hexagonal wurtzite structure. They are also homogenous with an average grain size of about 35 nm. For polymer nanocomposite, the optical properties are closely related to the ZnO content in the mixture. Among the tested active layers, the best performance is observed for that containing 2 wt% of ZnO nanoparticles. - Highlights: • We have analyzed the optical properties of PFE: ZnO nanocomposites . • We have optimized the best PFE: ZnO nanocomposite for the OLED application. • We have demonstrated the feasibility of white OLED devices

  4. [Kas sa Tammsaaret oled lugenud? Kirjanduslik eluloovestlus Helga Nõuga

    Index Scriptorium Estoniae

    2015-01-01

    Tutvustus: Kas sa Tammsaaret oled lugenud? : kirjanduslik eluloovestlus Helga Nõuga : [pühendatud Helga Nõu 80. sünnipäevale] / koostaja Rutt Hinrikus. Tartu : Eesti Kirjandusmuuseumi Teaduskirjastus, 2014 ; Helga Nõu. Valetaja : mälestused, tõeotsimised. Tallinn : Eesti Ajalehed, 2011

  5. Een blik in het binnenste van een witte oled

    NARCIS (Netherlands)

    Bobbert, P.A.; Coehoorn, R.

    2013-01-01

    Witte organische iicht-emitterende diodes (oleds) voor verlichting hebben organische lagen van siechts enkele nanometers dik. Om de efficiëntie en stabiliteit te kunnen verbeteren, moeten we te weten komen waar bet licht precies wordt geëmitteerd. Reconstructie van bet emissieprofiel uit de gemeten

  6. Ole Ivar Lovaas--His Life, Merits and Legacy

    Science.gov (United States)

    Özerk, Kamil; Vea, Gunvor Dalby; Eikeseth, Svein; Özerk, Meral

    2016-01-01

    Ole Ivar Lovaas (1927-2010) is known worldwide for his research within the field of Applied Behavior Analysis, and is probably the most influential researcher within the field of treatment of children with autism. In the first part of this biographically oriented paper, we inform the readers about his family background, childhood, elementary and…

  7. Linnugripp ei ole biorelv / Kevin Probert-Ehaver

    Index Scriptorium Estoniae

    Probert-Ehaver, Kevin

    2008-01-01

    Vastukaja 10. juulil Eesti Ekspressis ilmunud artiklile "Linnugripp - surm katseklaasist", milles väidetakse, et linnugripp ning teised uued nakkushaigused on biorelvad. Kriisireguleerimise konsultant selgitab, et nii Eesti kui ka Ameerika spetsialistide hinnangul ei ole linnugripp kuidagi seotud biorelvade programmiga

  8. Highly efficient orange and warm white phosphorescent OLEDs based on a host material with a carbazole-fluorenyl hybrid.

    Science.gov (United States)

    Du, Xiaoyang; Huang, Yun; Tao, Silu; Yang, Xiaoxia; Wu, Chuan; Wei, Huaixin; Chan, Mei-Yee; Yam, Vivian Wing-Wah; Lee, Chun-Sing

    2014-06-01

    A new carbazole-fluorenyl hybrid compound, 3,3'(2,7-di(naphthaline-2-yl)-9H-fluorene-9,9-diyl)bis(9-phenyl-9H-carbazole) (NFBC) was synthesized and characterized. The compound exhibits blue-violet emission both in solution and in film, with peaks centered at 404 and 420 nm. In addition to the application as a blue emitter, NFBC is demonstrated to be a good host for phosphorescent dopants. By doping Ir(2-phq)3 in NFBC, a highly efficient orange organic light-emitting diode (OLED) with a maximum efficiency of 32 cd A(-1) (26.5 Lm W(-1)) was obtained. Unlike most phosphorescent OLEDs, the device prepared in our study shows little efficiency roll-off at high brightness and maintains current efficiencies of 31.9 and 26.8 cd A(-1) at a luminance of 1000 and 10,000 cd m(-2), respectively. By using NFBC simultaneously as a blue fluorescence emitter and as a host for a phosphorescent dopant, a warm white OLED with a maximum efficiency of 22.9 Lm W(-1) (21.9 cd A(-1)) was also obtained. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. Efficient Phosphorescent OLEDS Based on Vacuum Deposition ...

    African Journals Online (AJOL)

    Thereby, we demonstrate high-efficiency organic light-emitting diodes by incorporating a double emission layer {i.e. both doped with the green phosphorescent dye tris(phenylpyridine)iridium [Ir(ppy)3]} into p-i-n-type device structure based on vacuum deposition technology. The intrinsic and doped transports layers are ...

  10. Addressing the efficiency roll-off in a fluorescent OLED by facile electron transport layer doping and carrier confinement

    Science.gov (United States)

    Soman, Anjaly; M, Manuraj; Unni, K. N. Narayanan

    2018-05-01

    Organic light emitting diodes (OLEDs) often face the issue of decreasing power efficiency with increasing brightness. Loss of charge carrier balance is one of the factors contributing to the efficiency roll-off. We demonstrate that by using a combination of doped electron transport layer (ETL) and a specially chosen electron blocking layer (EBL) having high hole mobility, this efficiency roll-off can be effectively suppressed. A tris-(8-hydroxyquinoline) aluminium (Alq3) based OLED has been fabricated with 2,3,6,7-Tetrahydro-1,1,7,7,-tetramethyl-1H, 5H,11H-10-(2-benzothiazolyl) quinolizino-[9,9a, 1n gh]coumarin (C545T) as the emissive dopant. Bulk doping of the ETL with lithium fluoride (LiF) was optimized to increase the luminous intensity as well as the current efficiency. An EBL with high hole mobility introduced between the EML and the hole transport layer (HTL) improved the performance drastically, and the device brightness at 9 V got improved by a factor of 2.5 compared to that of the control device. While increasing the brightness from 100 cd/m2 to 1000 cd/m2, the power efficiency drop was 47% for the control device whereas only a drop of 15% was observed for the modified device. The possible mechanisms for the enhanced performance are discussed.

  11. Architectural slicing

    DEFF Research Database (Denmark)

    Christensen, Henrik Bærbak; Hansen, Klaus Marius

    2013-01-01

    Architectural prototyping is a widely used practice, con- cerned with taking architectural decisions through experiments with light- weight implementations. However, many architectural decisions are only taken when systems are already (partially) implemented. This is prob- lematic in the context...... of architectural prototyping since experiments with full systems are complex and expensive and thus architectural learn- ing is hindered. In this paper, we propose a novel technique for harvest- ing architectural prototypes from existing systems, \\architectural slic- ing", based on dynamic program slicing. Given...... a system and a slicing criterion, architectural slicing produces an architectural prototype that contain the elements in the architecture that are dependent on the ele- ments in the slicing criterion. Furthermore, we present an initial design and implementation of an architectural slicer for Java....

  12. Achieving Extreme Utilization of Excitons by an Efficient Sandwich-Type Emissive Layer Architecture for Reduced Efficiency Roll-Off and Improved Operational Stability in Organic Light-Emitting Diodes.

    Science.gov (United States)

    Wu, Zhongbin; Sun, Ning; Zhu, Liping; Sun, Hengda; Wang, Jiaxiu; Yang, Dezhi; Qiao, Xianfeng; Chen, Jiangshan; Alshehri, Saad M; Ahamad, Tansir; Ma, Dongge

    2016-02-10

    It has been demonstrated that the efficiency roll-off is generally caused by the accumulation of excitons or charge carriers, which is intimately related to the emissive layer (EML) architecture in organic light-emitting diodes (OLEDs). In this article, an efficient sandwich-type EML structure with a mixed-host EML sandwiched between two single-host EMLs was designed to eliminate this accumulation, thus simultaneously achieving high efficiency, low efficiency roll-off and good operational stability in the resulting OLEDs. The devices show excellent electroluminescence performances, realizing a maximum external quantum efficiency (EQE) of 24.6% with a maximum power efficiency of 105.6 lm W(-1) and a maximum current efficiency of 93.5 cd A(-1). At the high brightness of 5,000 cd m(-2), they still remain as high as 23.3%, 71.1 lm W(-1), and 88.3 cd A(-1), respectively. And, the device lifetime is up to 2000 h at initial luminance of 1000 cd m(-2), which is significantly higher than that of compared devices with conventional EML structures. The improvement mechanism is systematically studied by the dependence of the exciton distribution in EML and the exciton quenching processes. It can be seen that the utilization of the efficient sandwich-type EML broadens the recombination zone width, thus greatly reducing the exciton quenching and increasing the probability of the exciton recombination. It is believed that the design concept provides a new avenue for us to achieve high-performance OLEDs.

  13. De Novo Design of Boron-Based Host Materials for Highly Efficient Blue and White Phosphorescent OLEDs with Low Efficiency Roll-Off.

    Science.gov (United States)

    Xue, Miao-Miao; Huang, Chen-Chao; Yuan, Yi; Cui, Lin-Song; Li, Yong-Xi; Wang, Bo; Jiang, Zuo-Quan; Fung, Man-Keung; Liao, Liang-Sheng

    2016-08-10

    Borane is an excellent electron-accepting species, and its derivatives have been widely used in a variety of fields. However, the use of borane derivatives as host materials in OLEDs has rarely reported because the device performance is generally not satisfactory. In this work, two novel spiro-bipolar hosts with incorporated borane were designed and synthesized. The strategies used in preparing these materials were to increase the spatial separation of the highest occupied molecular orbitals (HOMOs) and lowest unoccupied molecular orbitals (LUMOs) in the molecules, tune the connecting positions of functional groups, and incorporate specific functional groups with desirable thermal stability. Based on these designs, phosphorescent OLEDs with borane derivatives as hosts and with outstanding device performances were obtained. In particular, devices based on SAF-3-DMB/FIrpic exhibited an external quantum efficiency (EQE) of >25%. More encouragingly, the device was found to have quite a low efficiency roll-off, giving an efficiency of >20% even at a high brightness of 10000 cd/m(2). Furthermore, the EQE of the three-color-based (R + G + B) white OLED employing SAF-3-DMB as a host was also as high as 22.9% with CIE coordinates of (x, y) = (0.40, 0.48). At a brightness of 5000 cd/m(2), there was only a 3% decrease in EQE from its maximum value, implying a very low efficiency roll-off.

  14. Tetraaryl pyrenes: photophysical properties, computational studies, crystal structures, and application in OLEDs

    KAUST Repository

    El-Assaad, Tarek H.

    2015-10-15

    Pyrene was derivatized in positions 1, 3, 6, and 8 to yield a series of nine tetraarylpyrenes for which absorption, emission, emission lifetimes and solvatochromism in solution were determined. The fluorescence quantum yields in thin films and crystalline state, electrochemistry, and quantum-chemical calculations were completed for the series along with the X-ray crystal structure analysis of compounds 1, 2, 4, 5, 7, and 9. Compounds 2, 3, 4 as well as 7 were identified as the most suitable candidates for OLED application. Notably, in an unoptimized single-layer device geometry, these compounds exhibited blue electroluminescence coupled with impressively low turn-on voltages and high maximum luminances such as 2.8 V and 13 542 cd m-2 at 8.2 V for compound 2, respectively. © The Royal Society of Chemistry 2016.

  15. Tetraaryl pyrenes: photophysical properties, computational studies, crystal structures, and application in OLEDs

    KAUST Repository

    El-Assaad, Tarek H.; Auer, Manuel; Castañ eda, Raul; Hallal, Kassem M.; Jradi, Fadi M.; Mosca, Lorenzo; Khnayzer, Rony S.; Patra, Digambara; Timofeeva, Tatiana V.; Bredas, Jean-Luc; List-Kratochvil, Emil J. W.; Wex, Brigitte; Kaafarani, Bilal R.

    2015-01-01

    Pyrene was derivatized in positions 1, 3, 6, and 8 to yield a series of nine tetraarylpyrenes for which absorption, emission, emission lifetimes and solvatochromism in solution were determined. The fluorescence quantum yields in thin films and crystalline state, electrochemistry, and quantum-chemical calculations were completed for the series along with the X-ray crystal structure analysis of compounds 1, 2, 4, 5, 7, and 9. Compounds 2, 3, 4 as well as 7 were identified as the most suitable candidates for OLED application. Notably, in an unoptimized single-layer device geometry, these compounds exhibited blue electroluminescence coupled with impressively low turn-on voltages and high maximum luminances such as 2.8 V and 13 542 cd m-2 at 8.2 V for compound 2, respectively. © The Royal Society of Chemistry 2016.

  16. Highly efficient red OLEDs using DCJTB as the dopant and delayed fluorescent exciplex as the host.

    Science.gov (United States)

    Zhao, Bo; Zhang, Tianyou; Chu, Bei; Li, Wenlian; Su, Zisheng; Wu, Hairuo; Yan, Xingwu; Jin, Fangming; Gao, Yuan; Liu, Chengyuan

    2015-05-29

    In this manuscript, we demonstrated a highly efficient DCJTB emission with delayed fluorescent exciplex TCTA:3P-T2T as the host. For the 1.0% DCJTB doped concentration, a maximum luminance, current efficiency, power efficiency and EQE of 22,767 cd m(-2), 22.7 cd A(-1), 21.5 lm W(-1) and 10.15% were achieved, respectively. The device performance is the best compared to either red OLEDs with traditional fluorescent emitter or traditional red phosphor of Ir(piq)3 doped into CBP host. The extraction of so high efficiency can be explained as the efficient triplet excitons up-conversion of TCTA:3P-T2T and the energy transfer from exciplex host singlet state to DCJTB singlet state.

  17. GREEN LIGHT EMITTING TRICOMPONENT LUMINOPHORS OF 2-NAPHTHOL FOR CONSTRUCTION OF ORGANIC LIGHT EMITTING DEVICES

    OpenAIRE

    K. G. MANE , P. B. NAGORE , DR. S. R. PUJARI

    2018-01-01

    This article presents a previous study and incredible progress in basic theoretical modeling, and working for organic light-emitting devices (OLEDs) including preparation and characteristic studies of Organo- Luminescent Materials by conventional solid state reaction technique.

  18. Dielectric impedance and optical performance of quantum dots doped OLEDs

    Science.gov (United States)

    Jobin, Marc; Pellodi, Cédric; Emmenegger, Nicolas

    2016-04-01

    We investigate the effect of the incorporation of CdSe quantum dots (QD) in the standard ITO/TPD/Alq3/Al organic light emitting diodes (OLED's). The OLED's structures have been prepared in a double glove box coupled to a vacuum chamber containing both low and high temperature evaporators. For the standard (undoped) OLED's, the hole transport layer (HTL) consisting of 50nm of TPD is deposited by spin coating (8000rpm during 60 sec) and the 40nm of Alq3 were deposited at 2A/sec (organic crucible Radak-I). 150nm of Al were finally evaporated at 5A/s. For the CdSe-doped OLED's, the procedure was the same expect that the QD's were mixed with TPD in toluene before spin coating. During the thermal processing if the film, the QD's are expected to segregate to the surface, and then will be located at the TPD/Alq3 interface. The various layers were imaged by Atomic Force Microscopy (AFM) at each phase of the structure deposition, and we could indeed visualize the segregated QD's above the TPD film. AFM was systematically used to monitor the homogeneity and the thickness of the various films. The impedance of the non-encapsulated films structures were measured in air in the 40-40MHz frequency range, with bias at 0V (non-emitting), 2V (low emission) and 8V (strong emission). The corresponding dielectric spectra were analyzed with the standard Havriliak-Negami (HV) formula, where the conductive term has been subtracted from the data in case of light emission. We have measured a relaxation ranging from 100kHZ for the unbiased structure to 1MHz for 8V (strong emission). Apart from this expected relaxation, we found a second relaxation mechanism around 10 MHz. The origin of this second peak will be discussed. To monitor the optical emission of the OLED's, we have built a specific bench which allows for the quantitative measurement of the emission spectra and the dynamics behavior of the OLED's (raising and falling time). We found that the incorporation of the QD's unfortunately

  19. Novel Magnetic Devices

    National Research Council Canada - National Science Library

    Schuller, Ivan

    2007-01-01

    ...: ballistic magnetoresistance, magnetic field proximity effect and spin drag. These three phenomena would then be exploited for the design of novel device architectures and to investigate the physical principles behind these devices...

  20. Preparation of Cyano-Substituted Tetraphenylethylene Derivatives and Their Applications in Solution-Processable OLEDs

    Directory of Open Access Journals (Sweden)

    Xiaoyi Sun

    2018-01-01

    Full Text Available Creation of organic luminescent materials with high solid-state efficiency is of vital importance for their applications in optoelectronic fields. Here, a series of AIE luminogens (AIE gens, (Z-2,3-bis(4-(9,9-bis(6-(9H-carbazol-9-ylhexyl-9H-fluoren-2-ylphenyl-3-phenylacrylonitrile (SFC, and 2,3-bis(4-(9,9-bis(6-(9H-carbazol-9-ylhexyl-9H-fluoren-2-ylphenylfumaronitrile (DFC, utilizing 2,3,3-triphenylacrylonitrile and 2,3-diphenylfumaronitrile as respective centers, are designed and synthesized by Suzuki coupling reactions with high yields. The cis- and trans-isomers of DFC are also successfully obtained. All of them are thermally stable and show good solubility in common organic solvents. They all emit weakly in solution, but become strong emitters when fabricated into solid films. It is found introduction of one additional cyano group in DFC induced a big red-shift in solid-state emission, owing to its high electron-withdrawing ability. The cis- and trans-DFC show similar photophysical and Cyclic voltammogram (CV behaviors. Non-doped solution-processed organic light-emitting diodes (OLEDs using the three compounds as light-emitting layers are fabricated. SFC gives the best device performance with a maximum luminance of 5201 cd m−2, a maximum current efficiency of 3.67 cd A−1 and a maximum external quantum efficiencies (EQE of 1.37%. Red-shifted EL spectra are observed for cis- and trans-DFC-based device, and the OLED using trans-DFC as active layer exhibits better performance, which might derive from their different conformation in film state.

  1. Recombination region improvement for reduced efficiency roll-off in phosphorescent OLEDs with dual emissive layers

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Zhu; Zhou, Shunliang [State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China); Hu, Song [Chengdu Institute of Optics and Electronics, Chinese Academy of Sciences, Chengdu 610209 (China); Yu, Junsheng, E-mail: jsyu@uestc.edu.cn [State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)

    2014-10-15

    High-performance phosphorescent organic light-emitting diodes (PhOLEDs) by using dual-emissive-layer (DEL) structure to reduce efficiency roll-off were fabricated. The DEL was comprised of a hole-transport-type host of N, N′-bis(naphthalen-1-yl)-N, N′-bis(phenyl)-benzidine (NPB) and a bipolar host of 4,4′-bis(carbazol-9-yl)biphenyl (CBP), which were both doped with an orange phosphorescent dopant of bis[2-(4-tert-butylphenyl)-benzothiazolato-N,C2′]iridium (acetylacetonate) [(t-bt){sub 2}Ir(acac)]. After the optimization of doping concentration of the first emissive layer (FEL), the device with DEL exhibited 11% lower roll-off power efficiency than single emissive layer devices (SED) when the luminance increased from 1000 cd/m{sup 2} to 10,000 cd/m{sup 2}. The hole–electron recombination zone in DEL was illuminated by inserting an ultrathin fluorescent probe of 4-(dicyanomethylene)-2-tert-butyl-6 (1,1,7,7-tetramethyljulolidin-4-yl-vinyl)-4H-pyran (DCJTB) in different emissive regions. The performance improvement was attributed to the optimization of energy barrier and the expansion of exciton formation zone within the DEL. - Highlights: • PhOLEDs by using a dual-emissive-layer structure to reduce efficiency roll-off were fabricated. • The DED exhibited 11% lower efficiency roll-off, 57% lower turn-on voltage, and 174% higher brightness than SED. • A DCJTB fluorescent probe was inserted at different positions of DED to investigate the expansion of exciton formation zone.

  2. Architectural innovation foresight of thermoelectric generator charger integrated portable power supply for portable consumer electronic device in metropolitan market: The case study of Thailand

    Science.gov (United States)

    Maolikul, S.; Kiatgamolchai, S.; Chavarnakul, T.

    2012-06-01

    In the context of information and communication technology (ICT) trend for worldwide individuals, social life becomes digital and portable consumer electronic devices (PCED) powered by conventional power supply from batteries have been evolving through miniaturization and various function integration. Thermoelectric generators (TEG) were hypothesized for its potential role of battery charger to serve the shining PCED market. Hence, this paper, mainly focusing at the metropolitan market in Thailand, aimed to conduct architectural innovation foresight and to develop scenarios on potential exploitation approach of PCED battery power supply with TEG charger converting power from ambient heat source adjacent to individual's daily life. After technical review and assessment for TEG potential and battery aspect, the business research was conducted to analyze PCED consumer behavior for their PCED utilization pattern, power supply lack problems, and encountering heat sources/sinks in 3 modes: daily life, work, and leisure hobbies. Based on the secondary data analysis from literature and National Statistical Office of Thailand, quantitative analysis was applied using the cluster probability sampling methodology, statistically, with the sample size of 400 at 0.05 level of significance. In addition, the qualitative analysis was conducted to emphasize the rationale of consumer's behavior using in-depth qualitative interview. Scenario planning technique was also used to generate technological and market trend foresight. Innovation field and potential scenario for matching technology with market was proposed in this paper. The ingredient for successful commercialization of battery power supply with TEG charger for PCED market consists of 5 factors as follows: (1) PCED characteristic, (2) potential ambient heat sources/sinks, (3) battery module, (4) power management module, and the final jigsaw (5) characteristic and adequate arrangement of TEG modules. The foresight outcome for

  3. Efficiency enhancement of tandem organic light-emitting devices by a combined charge generation layer and organic n-type bis(ethylenedithio)-tetrathiafulvalene-doped electron transport layer

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Jin Taek; Kim, Dae Hun; Koh, Eun Im; Kim, Tae Whan

    2014-11-03

    While the operating voltage of the tandem organic light-emitting devices (OLEDs) with both an organic p-type 1,4,5,8,9,11-hexaazatriphenylene hexacarbonitrile charge generation layer and a bis(ethylenedithio)-tetrathiafulvalene (BEDT-TTF)-doped 1,3,5-tris(N-phenylbenzimiazole-2-yl)benzene (TPBi) electron transport layer (ETL) was 1.3 V lower than that of the tandem OLEDs with a BEDT-TTF-undoped TPBi ETL. Luminance efficiency of the tandem OLEDs with a BEDT-TTF-doped TPBi ETL was 3.6 cd/A higher than that of the typical OLEDs. The increase in the luminance efficiency and the decrease in the operating voltage of the tandem OLEDs were attributed to improved electron injection due to the insertion of the BEDT-TTF-doped TPBi ETL. - Highlights: • Tandem organic light-emitting diodes (OLED) were fabricated. • OLED fabricated with an n-type bis(ethylenedithio)-tetrathiafulvalene. • Operating voltage of the tandem OLED was decreased from 19.8 to 18.5 V. • Luminance efficiency of the tandem OLED was increased from 31.8 to 35.4 cd/A. • Enhancement of the luminance efficiency in the tandem OLED was achieved.

  4. Efficiency enhancement of tandem organic light-emitting devices by a combined charge generation layer and organic n-type bis(ethylenedithio)-tetrathiafulvalene-doped electron transport layer

    International Nuclear Information System (INIS)

    Cho, Jin Taek; Kim, Dae Hun; Koh, Eun Im; Kim, Tae Whan

    2014-01-01

    While the operating voltage of the tandem organic light-emitting devices (OLEDs) with both an organic p-type 1,4,5,8,9,11-hexaazatriphenylene hexacarbonitrile charge generation layer and a bis(ethylenedithio)-tetrathiafulvalene (BEDT-TTF)-doped 1,3,5-tris(N-phenylbenzimiazole-2-yl)benzene (TPBi) electron transport layer (ETL) was 1.3 V lower than that of the tandem OLEDs with a BEDT-TTF-undoped TPBi ETL. Luminance efficiency of the tandem OLEDs with a BEDT-TTF-doped TPBi ETL was 3.6 cd/A higher than that of the typical OLEDs. The increase in the luminance efficiency and the decrease in the operating voltage of the tandem OLEDs were attributed to improved electron injection due to the insertion of the BEDT-TTF-doped TPBi ETL. - Highlights: • Tandem organic light-emitting diodes (OLED) were fabricated. • OLED fabricated with an n-type bis(ethylenedithio)-tetrathiafulvalene. • Operating voltage of the tandem OLED was decreased from 19.8 to 18.5 V. • Luminance efficiency of the tandem OLED was increased from 31.8 to 35.4 cd/A. • Enhancement of the luminance efficiency in the tandem OLED was achieved

  5. La felicidad de los españoles: Factores explicativos

    OpenAIRE

    Namkee Ahn; F. Mochón

    2007-01-01

    El presente trabajo analiza los factores explicativos de la felicidad de los españoles. Los resultados son consistentes con lo establecido por la literatura disponible. Los divorciados y los viudos son notablemente más infelices que los casados, el desempleo a aparece fuertemente correlacionado con la infelicidad, la felicidad aumenta con la renta de forma decreciente, la salud tiene una notable incidencia en la felicidad y la religión se correlaciona positivamente con la felicidad. La inclus...

  6. Los españoles más viajeros

    Directory of Open Access Journals (Sweden)

    Javier Callejo Gallego

    2008-01-01

    Full Text Available A partir de una explotación específica de los datos aportados por la encuesta que en mayor medida recoge las actividades y movimientos turísticos de los españoles, Familitur (dirigida por el Instituto de Estudios Turísticos, se analiza el comportamiento de aquellos españoles que registran una mayor frecuencia de viajes a lo largo del año. La perspectiva de tal aproximación es inicialmente descriptiva: conocer hasta qué punto configuran un perfil social diferenciado o realizan otro tipo de viajes. Es decir, hasta qué punto se diferencian de los otros españoles, más allá de la diferencia que les singulariza como más viajeros. Pero también se intenta, con los límites derivados de las características de los datos obtenidos, avanzar explicaciones sobre tal diferenciación.

  7. Very high efficiency phosphorescent organic light-emitting devices by using rough indium tin oxide

    International Nuclear Information System (INIS)

    Zhang, Yingjie; Aziz, Hany

    2014-01-01

    The efficiency of organic light-emitting devices (OLEDs) is shown to significantly depend on the roughness of the indium tin oxide (ITO) anode. By using rougher ITO, light trapped in the ITO/organic wave-guided mode can be efficiently extracted, and a light outcoupling enhancement as high as 40% is achieved. Moreover, contrary to expectations, the lifetime of OLEDs is not affected by ITO roughness. Finally, an OLED employing rough ITO anode that exhibits a current efficiency of 56 cd/A at the remarkably high brightness of 10 5  cd/m 2 is obtained. This represents the highest current efficiency at such high brightness to date for an OLED utilizing an ITO anode, without any external light outcoupling techniques. The results demonstrate the significant efficiency benefits of using ITO with higher roughness in OLEDs.

  8. Very high efficiency phosphorescent organic light-emitting devices by using rough indium tin oxide

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Yingjie; Aziz, Hany, E-mail: h2aziz@uwaterloo.ca [Department of Electrical and Computer Engineering and Waterloo Institute for Nanotechnology, University of Waterloo, 200 University Avenue West, Waterloo, Ontario N2L 3G1 (Canada)

    2014-07-07

    The efficiency of organic light-emitting devices (OLEDs) is shown to significantly depend on the roughness of the indium tin oxide (ITO) anode. By using rougher ITO, light trapped in the ITO/organic wave-guided mode can be efficiently extracted, and a light outcoupling enhancement as high as 40% is achieved. Moreover, contrary to expectations, the lifetime of OLEDs is not affected by ITO roughness. Finally, an OLED employing rough ITO anode that exhibits a current efficiency of 56 cd/A at the remarkably high brightness of 10{sup 5} cd/m{sup 2} is obtained. This represents the highest current efficiency at such high brightness to date for an OLED utilizing an ITO anode, without any external light outcoupling techniques. The results demonstrate the significant efficiency benefits of using ITO with higher roughness in OLEDs.

  9. Low driving voltage simplified tandem organic light-emitting devices by using exciplex-forming hosts

    Science.gov (United States)

    Zhou, Dong-Ying; Cui, Lin-Song; Zhang, Ying-Jie; Liao, Liang-Sheng; Aziz, Hany

    2014-10-01

    Tandem organic light-emitting devices (OLEDs), i.e., OLEDs containing multiple electroluminescence (EL) units that are vertically stacked, are attracting significant interest because of their ability to realize high current efficiency and long operational lifetime. However, stacking multiple EL units in tandem OLEDs increases driving voltage and complicates fabrication process relative to their standard single unit counterparts. In this paper, we demonstrate low driving voltage tandem OLEDs via utilizing exciplex-forming hosts in the EL units instead of conventional host materials. The use of exciplex-forming hosts reduces the charge injection barriers and the trapping of charges on guest molecules, resulting in the lower driving voltage. The use of exciplex-forming hosts also allows using fewer layers, hence simpler EL configuration which is beneficial for reducing the fabrication complexity of tandem OLEDs.

  10. Life prediction for white OLED based on LSM under lognormal distribution

    Science.gov (United States)

    Zhang, Jianping; Liu, Fang; Liu, Yu; Wu, Helen; Zhu, Wenqing; Wu, Wenli; Wu, Liang

    2012-09-01

    In order to acquire the reliability information of White Organic Light Emitting Display (OLED), three groups of OLED constant stress accelerated life tests (CSALTs) were carried out to obtain failure data of samples. Lognormal distribution function was applied to describe OLED life distribution, and the accelerated life equation was determined by Least square method (LSM). The Kolmogorov-Smirnov test was performed to verify whether the white OLED life meets lognormal distribution or not. Author-developed software was employed to predict the average life and the median life. The numerical results indicate that the white OLED life submits to lognormal distribution, and that the accelerated life equation meets inverse power law completely. The estimated life information of the white OLED provides manufacturers and customers with important guidelines.

  11. Compact and efficient method of RGB to RGBW data conversion for OLED microdisplays

    OpenAIRE

    Can, Chi

    2012-01-01

    Colour Electronic Information Displays (EIDs) typically consist of pixels that are made up of red, green and blue (RGB) subpixels. A recent technology, Organic Light Emitting Diode (OLED), offers the potential to create a superior EID. OLED is already suitable for use in small displays and microdisplays for personal electronics products. OLED microdisplays, in particular, exhibit lower power consumption than equivalent direct-view panels thus enabling microdisplay-based persona...

  12. Formation of blade and slot die coated small molecule multilayers for OLED applications studied theoretically and by XPS depth profiling

    Science.gov (United States)

    Peters, Katharina; Raupp, Sebastian; Hummel, Helga; Bruns, Michael; Scharfer, Philip; Schabel, Wilhelm

    2016-06-01

    Slot die coaters especially designed for low material consumption and doctor blades were used to process small molecule solutions for organic light-emitting diodes (OLEDs). Optimum process parameters were developed for the large-scale coating techniques to generate stable single and multiple layers only a few nanometers thick. Achieving a multilayer architecture for solution-processed OLEDs is the most challenging step. X-ray photoelectron spectroscopy sputter depth profiling was performed to determine defined interfaces between coated organic layers. Commercially available small molecules NPB (N,N'-Di(1-naphthyl)-N,N'-diphenyl-(1,1'-biphenyl)-4,4'-diamine) and BAlq (Bis(8-hdroxy-2methylquinoline)-(4-phenylphenoxy)aluminum), originally developed for vacuum deposition, were used as hole, respectively electron transport material. Defined double-layers were processed with both scalable coating methods using the orthogonal solvent approach. The use of non-orthogonal solvents resulted in complete intermixing of the material. The results are explained by calculations of solubilities and simulating drying and diffusion kinetics of the small molecule solutions.

  13. Formation of blade and slot die coated small molecule multilayers for OLED applications studied theoretically and by XPS depth profiling

    Directory of Open Access Journals (Sweden)

    Katharina Peters

    2016-06-01

    Full Text Available Slot die coaters especially designed for low material consumption and doctor blades were used to process small molecule solutions for organic light-emitting diodes (OLEDs. Optimum process parameters were developed for the large-scale coating techniques to generate stable single and multiple layers only a few nanometers thick. Achieving a multilayer architecture for solution-processed OLEDs is the most challenging step. X-ray photoelectron spectroscopy sputter depth profiling was performed to determine defined interfaces between coated organic layers. Commercially available small molecules NPB (N,N’-Di(1-naphthyl-N,N’-diphenyl-(1,1’-biphenyl-4,4’-diamine and BAlq (Bis(8-hdroxy-2methylquinoline-(4-phenylphenoxyaluminum, originally developed for vacuum deposition, were used as hole, respectively electron transport material. Defined double-layers were processed with both scalable coating methods using the orthogonal solvent approach. The use of non-orthogonal solvents resulted in complete intermixing of the material. The results are explained by calculations of solubilities and simulating drying and diffusion kinetics of the small molecule solutions.

  14. Formation of blade and slot die coated small molecule multilayers for OLED applications studied theoretically and by XPS depth profiling

    Energy Technology Data Exchange (ETDEWEB)

    Peters, Katharina; Raupp, Sebastian, E-mail: sebastian.raupp@kit.edu; Scharfer, Philip; Schabel, Wilhelm [Institute of Thermal Process Engineering, Thin Film Technology, Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany); Hummel, Helga [Philips Technologie GmbH Innovative Technologies, Aachen (Germany); Bruns, Michael [Institute for Applied Materials and Karlsruhe Nano Micro Facility (KNMF), Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany)

    2016-06-15

    Slot die coaters especially designed for low material consumption and doctor blades were used to process small molecule solutions for organic light-emitting diodes (OLEDs). Optimum process parameters were developed for the large-scale coating techniques to generate stable single and multiple layers only a few nanometers thick. Achieving a multilayer architecture for solution-processed OLEDs is the most challenging step. X-ray photoelectron spectroscopy sputter depth profiling was performed to determine defined interfaces between coated organic layers. Commercially available small molecules NPB (N,N’-Di(1-naphthyl)-N,N’-diphenyl-(1,1’-biphenyl)-4,4’-diamine) and BAlq (Bis(8-hdroxy-2methylquinoline)-(4-phenylphenoxy)aluminum), originally developed for vacuum deposition, were used as hole, respectively electron transport material. Defined double-layers were processed with both scalable coating methods using the orthogonal solvent approach. The use of non-orthogonal solvents resulted in complete intermixing of the material. The results are explained by calculations of solubilities and simulating drying and diffusion kinetics of the small molecule solutions.

  15. Robotic architectures

    CSIR Research Space (South Africa)

    Mtshali, M

    2010-01-01

    Full Text Available In the development of mobile robotic systems, a robotic architecture plays a crucial role in interconnecting all the sub-systems and controlling the system. The design of robotic architectures for mobile autonomous robots is a challenging...

  16. Low temperature transient response and electroluminescence characteristics of OLEDs based on Alq{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, Chao [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); College of Materials Science and Optoelectronic Devices, University of Chinese Academy of Sciences, Beijing 100049 (China); Guan, Min, E-mail: guanmin@semi.ac.cn [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); Zhang, Yang [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); College of Materials Science and Optoelectronic Devices, University of Chinese Academy of Sciences, Beijing 100049 (China); Li, Yiyang; Liu, Shuangjie [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); Zeng, Yiping [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); College of Materials Science and Optoelectronic Devices, University of Chinese Academy of Sciences, Beijing 100049 (China)

    2017-08-15

    Highlights: • The dependency relation between transmission rate and electron transport layer is revealed. • The critical temperature points for the influence of luminescent materials and injection barriers on delay time are found. • The influence of light-emitting material and injection layer on carrier accumulation is quantified. - Abstract: In this work, the organic light-emitting diodes (OLEDs) based on Alq{sub 3} are fabricated. In order to make clear the transport mechanism of carriers in organic light-emitting devices at low temperature, detailed electroluminescence transient response and the current-voltage–luminescence (I–V–L) characteristics under different temperatures in those OLEDs are investigated. It founds that the acceleration of brightness increases with increasing temperature is maximum when the temperature is 200 K and it is mainly affected by the electron transport layer (Alq{sub 3}). The MoO{sub 3} injection layer and the electroluminescent layer have great influence on the delay time when the temperature is 200 K. Once the temperature is greater than 250 K, the delay time is mainly affected by the MoO{sub 3} injection layer. On the contrary, the fall time is mainly affected by the electroluminescent material. The V{sub f} is the average growth rate of fall time when the temperature increases 1 K which represents the accumulation rate of carriers. The difference between V{sub f} caused by the MoO{sub 3} injection layer is 0.52 us/K and caused by the electroluminescent material Ir(ppy){sub 3} is 0.73 us/K.

  17. Architecture & Environment

    Science.gov (United States)

    Erickson, Mary; Delahunt, Michael

    2010-01-01

    Most art teachers would agree that architecture is an important form of visual art, but they do not always include it in their curriculums. In this article, the authors share core ideas from "Architecture and Environment," a teaching resource that they developed out of a long-term interest in teaching architecture and their fascination with the…

  18. Novel Hole Transporting Materials Based on 4-(9H-Carbazol-9-yltriphenylamine Derivatives for OLEDs

    Directory of Open Access Journals (Sweden)

    Quynh Pham Bao Nguyen

    2014-09-01

    Full Text Available During the past few years, organic light emitting diodes (OLEDs have been increasingly studied due to their emerging applicability. However, some of the properties of existing OLEDs could be improved, such as their overall efficiency and durability; these aspects have been addressed in the current study. A series of novel hole-transporting materials (HTMs 3a–c based on 4-(9H-carbazol-9-yltriphenylamine conjugated with different carbazole or triphenylamine derivatives have been readily synthesized by Suzuki coupling reactions. The resulting compounds showed good thermal stabilities with high glass transition temperatures between 148 and 165 °C. The introduction of HTMs 3b and 3c into the standard devices ITO/HATCN/NPB/HTMs 3 (indium tin oxide/dipyrazino(2,3-f:2ꞌ,3ꞌ-hquinoxaline 2,3,6,7,10,11-hexacarbonitrile/N,Nꞌ-bis(naphthalen-1-yl-N,Nꞌ-bis(phenyl-benzidine/HTMs/CBP (4,4ꞌ-Bis(N-carbazolyl-1,1ꞌ-biphenyl: 5% Ir(ppy3/Bphen/LiF/Al (tris[2-phenylpyridinato-C2,N]iridium(III/4,7-diphenyl-1,10-phenanthroline/LiF/Al resulted in significantly enhanced current, power, and external quantum efficiencies (EQE as compared to the reference device without any layers of HTMs 3.

  19. Red phosphorescent organic light-emitting diodes (PhOLEDs) based on a heteroleptic cyclometalated Iridium (III) complex

    Energy Technology Data Exchange (ETDEWEB)

    Lepeltier, Marc [Institut Lavoisier de Versailles, UMR 8180 CNRS, Université de Versailles Saint-Quentin en Yvelines, 45 avenue des Etats-Unis, 78035 Versailles Cedex (France); Dumur, Frédéric, E-mail: frederic.dumur@univ-amu.fr [Aix-Marseille Université, CNRS, ICR, UMR 7273, F-13397 Marseille (France); Wantz, Guillaume, E-mail: guillaume.wantz@ims-bordeaux.fr [University of Bordeaux, IMS, UMR 5218, F-33400 Talence (France); CNRS, IMS, UMR 5218, F-33400 Talence (France); Vila, Neus; Mbomekallé, Israel [Institut Lavoisier de Versailles, UMR 8180 CNRS, Université de Versailles Saint-Quentin en Yvelines, 45 avenue des Etats-Unis, 78035 Versailles Cedex (France); Bertin, Denis; Gigmes, Didier [Aix-Marseille Université, CNRS, ICR, UMR 7273, F-13397 Marseille (France); Mayer, Cédric R., E-mail: cmayer@lisv.uvsq.fr [Laboratoire d’Ingénierie des Systèmes de Versailles LISV – EA 4048, Université de Versailles Saint Quentin en Yvelines, 10/12 avenue de l’Europe, 78140 Vélizy (France)

    2013-11-15

    Highly efficient red-emitting Phosphorescent Organic Light-Emitting Diodes (PhOLEDs) based on a neutral vacuum-sublimatable heteroleptic iridium (III) complex have been designed and studied. Heteroleptic complex Ir(piq){sub 2}(acac) was prepared in one step with acetylacetone (acac) as the ancillary ligand. Electronic and spectroscopic properties of Ir(piq){sub 2}(acac) were investigated by UV–visible absorption, fluorescence spectroscopy and cyclic voltammetry. Electrophosphorescent devices comprising Ir(piq){sub 2}(acac) as dopant of TCTA exhibited outstanding electroluminescence performance with a current efficiency of 10.0 cd A{sup −1}, a maximum power efficiency of 7.2 lm W{sup −1} and a maximal brightness of 3540 cd m{sup −2} was reached at 8.0 V. CIE coordinates close to the standard red of the national television system committee were obtained (0.67, 0.33). -- Highlights: • A saturated red OLED has been prepared. • High power efficiency and brightness were obtained. • Thickness of the device was determined as a parameter determining the overall performance. • CIE coordinates close to the standard red of the national television system committee were obtained.

  20. Light emission in forward and reverse bias operation in OLED with amorphous silicon carbon nitride thin films

    Science.gov (United States)

    Reyes, R.; Cremona, M.; Achete, C. A.

    2011-01-01

    Amorphous silicon carbon nitride (a-SiC:N) thin films deposited by magnetron sputtering were used in the structure of an organic light emitting diode (OLED), obtaining an OLED operating in forward and reverse bias mode. The device consist of the heterojunction structure ITO/a-SiC:N/Hole Transport Layer (HTL)/ Electron Transport Layer (ETL)/a-SiC:N/Al. As hole transporting layer was used a thin film of 1-(3-methylphenyl)-1,2,3,4 tetrahydroquinoline - 6 - carboxyaldehyde - 1,1'- diphenylhydrazone (MTCD), while the tris(8-hydroxyquinoline aluminum) (Alq3) is used as electron transport and emitting layer. A significant increase in the voltage operation compared to the conventional ITO/MTCD/Alq3/Al structure was observed, so the onset of electroluminescence occurs at about 22 V in the forward and reverse bias mode of operation. The electroluminescence spectra is similar in both cases, only slightly shifted 0.14 eV to lower energies in relation to the conventional device.

  1. High-Performance Doping-Free Hybrid White OLEDs Based on Blue Aggregation-Induced Emission Luminogens.

    Science.gov (United States)

    Liu, Baiquan; Nie, Han; Lin, Gengwei; Hu, Shiben; Gao, Dongyu; Zou, Jianhua; Xu, Miao; Wang, Lei; Zhao, Zujin; Ning, Honglong; Peng, Junbiao; Cao, Yong; Tang, Ben Zhong

    2017-10-04

    Doping-free white organic light-emitting diodes (DF-WOLEDs) have aroused research interest because of their simple properties. However, to achieve doping-free hybrid WOLEDs (DFH-WOLEDs), avoiding aggregation-caused quenching is challenging. Herein, blue luminogens with aggregation-induced emission (AIE) characteristics, for the first time, have been demonstrated to develop DFH-WOLEDs. Unlike previous DFH-WOLEDs, both thin (10 nm) AIE luminogen (AIEgen) can be used for devices, enhancing the flexibility. Two-color devices show (i) pure-white emission, (ii) high CRI (85), and (iii) high efficiency. Particularly, 19.0 lm W 1- is the highest for pure-white DF-WOLEDs, while 35.0 lm W 1- is the best for two-color hybrid WOLEDs with CRI ≥ 80. A three-color DFH-WOLED shows broad color-correlated temperature span (2301-11628 K), (i) the first sunlight-like OLED (2500-8000 K) operating at low voltages, (ii) the broadest span among sunlight-like OLED, and (iii) possesses comparable efficiency with the best doping counterpart. Another three-color DFH-WOLED exhibits CRI > 90 at ≥3000 cd m -2 , (i) the first DF-WOLED with CRI ≥ 90 at high luminances, and (ii) the CRI (92.8) is not only the highest among AIE-based WOLEDs but also the highest among DF-WOLEDs. Such findings may unlock an alternative concept to develop DFH-WOLEDs.

  2. Light emission in forward and reverse bias operation in OLED with amorphous silicon carbon nitride thin films

    Energy Technology Data Exchange (ETDEWEB)

    Reyes, R [Facultad de Ingenieria Quimica y Textil, Universidad Nacional de Ingenieria, Av. Tupac Amaru SN, Lima (Peru); Cremona, M [Departamento de Fisica, PontifIcia Universidade Catolica de Rio de Janeiro, PUC-Rio, Cx. Postal 38071, Rio de Janeiro, RJ, CEP 22453-970 (Brazil); Achete, C A, E-mail: rreyes@uni.edu.pe [Departamento de Engenheria Metalurgica e de Materiais, Universidade Federal do Rio de Janeiro, Cx. Postal 68505, Rio de Janeiro, RJ, CEP 21945-970 (Brazil)

    2011-01-01

    Amorphous silicon carbon nitride (a-SiC:N) thin films deposited by magnetron sputtering were used in the structure of an organic light emitting diode (OLED), obtaining an OLED operating in forward and reverse bias mode. The device consist of the heterojunction structure ITO/a-SiC:N/Hole Transport Layer (HTL)/ Electron Transport Layer (ETL)/a-SiC:N/Al. As hole transporting layer was used a thin film of 1-(3-methylphenyl)-1,2,3,4 tetrahydroquinoline - 6 - carboxyaldehyde - 1,1'- diphenylhydrazone (MTCD), while the tris(8-hydroxyquinoline aluminum) (Alq{sub 3}) is used as electron transport and emitting layer. A significant increase in the voltage operation compared to the conventional ITO/MTCD/Alq{sub 3}/Al structure was observed, so the onset of electroluminescence occurs at about 22 V in the forward and reverse bias mode of operation. The electroluminescence spectra is similar in both cases, only slightly shifted 0.14 eV to lower energies in relation to the conventional device.

  3. Light emission in forward and reverse bias operation in OLED with amorphous silicon carbon nitride thin films

    International Nuclear Information System (INIS)

    Reyes, R; Cremona, M; Achete, C A

    2011-01-01

    Amorphous silicon carbon nitride (a-SiC:N) thin films deposited by magnetron sputtering were used in the structure of an organic light emitting diode (OLED), obtaining an OLED operating in forward and reverse bias mode. The device consist of the heterojunction structure ITO/a-SiC:N/Hole Transport Layer (HTL)/ Electron Transport Layer (ETL)/a-SiC:N/Al. As hole transporting layer was used a thin film of 1-(3-methylphenyl)-1,2,3,4 tetrahydroquinoline - 6 - carboxyaldehyde - 1,1'- diphenylhydrazone (MTCD), while the tris(8-hydroxyquinoline aluminum) (Alq 3 ) is used as electron transport and emitting layer. A significant increase in the voltage operation compared to the conventional ITO/MTCD/Alq 3 /Al structure was observed, so the onset of electroluminescence occurs at about 22 V in the forward and reverse bias mode of operation. The electroluminescence spectra is similar in both cases, only slightly shifted 0.14 eV to lower energies in relation to the conventional device.

  4. Investigations of solution-processed charge generation unit with low concentration of small molecule doped in p-type/HAT-CN{sub 6} for tandem OLED

    Energy Technology Data Exchange (ETDEWEB)

    Talik, N.A., E-mail: azrina_talik@hotmail.com [Low Dimensional Material Research Centre (LDMRC), Physics Dept., Faculty of Science, University of Malaya, 50603 Kuala Lumpur (Malaysia); Yeoh, K.H. [Low Dimensional Material Research Centre (LDMRC), Physics Dept., Faculty of Science, University of Malaya, 50603 Kuala Lumpur (Malaysia); Centre for Photonics and Advanced Materials Research (CPR), Lee Kong Chian Faculty of Engineering and Science, University Tunku Abdul Rahman, 43000 Kajang, Selangor (Malaysia); Ng, C.Y.B. [Low Dimensional Material Research Centre (LDMRC), Physics Dept., Faculty of Science, University of Malaya, 50603 Kuala Lumpur (Malaysia); Tan, C.Y. [Centre of Advanced Manufacturing & Material Processing (AMMP), Department of Mechanical Engineering, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia); Yap, B.K., E-mail: kbyap@uniten.edu.my [Centre of Microelectronic and Nano Engineering (CeMNE), College of Engineering, Universiti Tenaga Nasional, 43000 Kajang, Selangor (Malaysia)

    2016-01-15

    We investigated the charge generation and injection mechanism in solution processed charge generation unit (CGU) used in our high performance tandem organic light emitting diode (OLED) via capacitance–voltage (C–V) and current density–voltage (J–V) measurements. By doping 2 wt% of small molecule 1,1-bis-(4-bis(4-tolyl)-aminophenyl) cyclohexene (TAPC) into Poly (N-vinylcarbazole) (PVK) as p-type layer of the CGU, we obtained more than two folds improvement in the tandem device efficiency compared to single device. The performance improvement of the TAPC doped CGU could be attributed to low built-in potential, large vacuum level shift as well as high charge density for efficient charge generation. - Highlights: • Charge-generation and injection mechanism in CGU for tandem OLED is investigated. • Small molecule, TAPC doped in p-type/HAT-CN{sub 6} has been used for tandem OLED. • The improvement attributes to the lower V{sub bi} and larger ΔV{sub L} in doped layer. • Narrower W and high carrier density also contribute to efficiency improvement.

  5. Investigations of solution-processed charge generation unit with low concentration of small molecule doped in p-type/HAT-CN6 for tandem OLED

    International Nuclear Information System (INIS)

    Talik, N.A.; Yeoh, K.H.; Ng, C.Y.B.; Tan, C.Y.; Yap, B.K.

    2016-01-01

    We investigated the charge generation and injection mechanism in solution processed charge generation unit (CGU) used in our high performance tandem organic light emitting diode (OLED) via capacitance–voltage (C–V) and current density–voltage (J–V) measurements. By doping 2 wt% of small molecule 1,1-bis-(4-bis(4-tolyl)-aminophenyl) cyclohexene (TAPC) into Poly (N-vinylcarbazole) (PVK) as p-type layer of the CGU, we obtained more than two folds improvement in the tandem device efficiency compared to single device. The performance improvement of the TAPC doped CGU could be attributed to low built-in potential, large vacuum level shift as well as high charge density for efficient charge generation. - Highlights: • Charge-generation and injection mechanism in CGU for tandem OLED is investigated. • Small molecule, TAPC doped in p-type/HAT-CN 6 has been used for tandem OLED. • The improvement attributes to the lower V bi and larger ΔV L in doped layer. • Narrower W and high carrier density also contribute to efficiency improvement.

  6. Near-Infrared to Visible Organic Upconversion Devices Based on Organic Light-Emitting Field Effect Transistors.

    Science.gov (United States)

    Li, Dongwei; Hu, Yongsheng; Zhang, Nan; Lv, Ying; Lin, Jie; Guo, Xiaoyang; Fan, Yi; Luo, Jinsong; Liu, Xingyuan

    2017-10-18

    The near-infrared (NIR) to visible upconversion devices have attracted great attention because of their potential applications in the fields of night vision, medical imaging, and military security. Herein, a novel all-organic upconversion device architecture has been first proposed and developed by incorporating a NIR absorption layer between the carrier transport layer and the emission layer in heterostructured organic light-emitting field effect transistors (OLEFETs). The as-prepared devices show a typical photon-to-photon upconversion efficiency as high as 7% (maximum of 28.7% under low incident NIR power intensity) and millisecond-scale response time, which are the highest upconversion efficiency and one of the fastest response time among organic upconversion devices as referred to the previous reports up to now. The high upconversion performance mainly originates from the gain mechanism of field-effect transistor structures and the unique advantage of OLEFETs to balance between the photodetection and light emission. Meanwhile, the strategy of OLEFETs also offers the advantage of high integration so that no extra OLED is needed in the organic upconversion devices. The results would pave way for low-cost, flexible and portable organic upconversion devices with high efficiency and simplified processing.

  7. Molecular-wire behavior of OLED materials: exciton dynamics in multichromophoric Alq3-oligofluorene-Pt(II)porphyrin triads.

    Science.gov (United States)

    Montes, Victor A; Pérez-Bolívar, César; Agarwal, Neeraj; Shinar, Joseph; Anzenbacher, Pavel

    2006-09-27

    Donor-bridge-acceptor triads consisting of the Alq3 complex, oligofluorene bridge, and PtII tetraphenylporphyrin (PtTPP) were synthesized. The triads were designed to study the energy level/distance-dependence in energy transfer both in a solution and in solid state. The materials show effective singlet transfer from the Alq3-fluorene fluorophore to the porphyrin, while the triplet energy transfer, owing to the shorter delocalization of triplet excitons, appears to take place via a triplet energy cascade. Using femtosecond transient spectroscopy, the rate of the singlet-singlet energy transfer was determined. The exponential dependence of the donor-acceptor distance and the respective energy transfer rates of 7.1 x 1010 to 1.0 x 109 s-1 with the attenuation factor â of 0.21 +/- 0.02 A-1 suggest that the energy transfer proceeds via a mixed incohererent wire/superexchange mechanism. In the OLEDs fabricated using the Alq3-oligofluorene-PtTPP triads with better triplet level alignment, the order of a magnitude increase in efficacy appears to be due to facile triplet energy transfer. The devices, where the triplet-triplet energy transfer is of paramount importance, showed high color purity emission (CIE X,Y: 0.706, 0.277), which is almost identical to the emission from thin films. Most importantly, we believe that the design principles demonstrated above are general and may be used to prepare OLED materials with enhanced quantum efficacy at lowered operational potentials, being crucial for improved lifespan of OLEDs.

  8. STUDY OF DEGRADATION MECHANISM AND PACKAGING OF ORGANIC LIGHT EMITTING DEVICES

    Institute of Scientific and Technical Information of China (English)

    Gu Xu

    2003-01-01

    Organic Light Emitting Devices (OLED) have attracted much attention recently, for their applications in future Flat Panel Displays and lighting products. However, their fast degradation remained a major obstacle to their commercialization. Here we present a brief summary of our studies on both extrinsic and intrinsic causes for the fast degradation of OLEDs. In particular, we focus on the origin of the dark spots by "rebuilding" cathodes, which confirms that the growth of dark spots occurs primarily due to cathode delamination. In the meantime, we recapture the findings from the search for suitable OLED packaging materials, in particular polymer composites, which provide both heat dissipation and moisture resistance, in addition to electrical insulation.

  9. Los jueces españoles como jueces de la Unión Europea

    DEFF Research Database (Denmark)

    Mayoral, Juan A.; Ordóñez Solís, David; Berberoff, Dimitry

    2013-01-01

    sentido, el presente estudio trata de esclarecer si actualmente los jueces españoles se han adaptado a las exigencias creadas por el sistema legal de la Unión para la aplicación del derecho europeo. Para comprobar si los jueces españoles han asimilado su condición de jueces europeos, operando como...

  10. GATEWAY Demonstrations: OLED Lighting in the Offices of Aurora Lighting Design, Inc.

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Naomi J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-03-31

    At the offices of Aurora Lighting Design, Inc., in Grayslake, IL, the GATEWAY program conducted its first investigation involving OLED lighting. The project experienced several challenges, but also highlighted a number of promising attributes – which indicate that with continued improvements in efficacy, longevity, size, and flexibility, OLEDs could provide a new tool for creative and effective lighting.

  11. Life prediction of OLED for constant-stress accelerated degradation tests using luminance decaying model

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Jianping, E-mail: jpzhanglzu@163.com [College of Energy and Mechanical Engineering, Shanghai University of Electric Power, Shanghai 200090 (China); Li, Wenbin [College of Energy and Mechanical Engineering, Shanghai University of Electric Power, Shanghai 200090 (China); Cheng, Guoliang; Chen, Xiao [Shanghai Tianyi Electric Co., Ltd., Shanghai 201611 (China); Wu, Helen [School of Computing, Engineering and Mathematics, University of Western Sydney, Sydney 2751 (Australia); Herman Shen, M.-H. [Department of Mechanical and Aerospace Engineering, The Ohio State University, OH 43210 (United States)

    2014-10-15

    In order to acquire the life information of organic light emitting diode (OLED), three groups of constant stress accelerated degradation tests are performed to obtain the luminance decaying data of samples under the condition that the luminance and the current are respectively selected as the indicator of performance degradation and the test stress. Weibull function is applied to describe the relationship between luminance decaying and time, least square method (LSM) is employed to calculate the shape parameter and scale parameter, and the life prediction of OLED is achieved. The numerical results indicate that the accelerated degradation test and the luminance decaying model reveal the luminance decaying law of OLED. The luminance decaying formula fits the test data very well, and the average error of fitting value compared with the test data is small. Furthermore, the accuracy of the OLED life predicted by luminance decaying model is high, which enable rapid estimation of OLED life and provide significant guidelines to help engineers make decisions in design and manufacturing strategy from the aspect of reliability life. - Highlights: • We gain luminance decaying data by accelerated degradation tests on OLED. • The luminance decaying model objectively reveals the decaying law of OLED luminance. • The least square method (LSM) is employed to calculate Weibull parameters. • The plan designed for accelerated degradation tests proves to be feasible. • The accuracy of the OLED life and the luminance decaying fitting formula is high.

  12. Flexible barrier technology for enabling rollable AMOLED displays and upscaling flexible OLED lighting

    NARCIS (Netherlands)

    Li, F.M.; Unnikrishnan, S.; Weijer, P. van de; Assche, F. van; Shen, J.; Ellis, T.; Manders, W.; Akkerman, H.; Bouten, P.; Mol, A.M.B. van

    2013-01-01

    The availability of a high performance thin-film barrier is the most critical challenge in upscaling and commercializing flexible OLED products. We report a flexible thin-film-barrier technology that meets lifetime specifications for OLED lighting, and demonstrate it in rollable QVGA a-IGZO AMOLED

  13. Kinetic Monte Carlo study of sensitiviy of OLED efficiency and lifetime to materials parameters

    NARCIS (Netherlands)

    Coehoorn, R.; Eersel, van H.; Bobbert, P.A.; Janssen, R.A.J.

    2015-01-01

    The performance of organic light-emitting diodes (OLEDs) is determined by a complex interplay of the optoelectronic processes in the active layer stack. In order to enable simulation-assisted layer stack development, a three-dimensional kinetic Monte Carlo OLED simulation method which includes the

  14. An approach to integrated design based componet software and OLE-technology

    DEFF Research Database (Denmark)

    Bagger-Petersen, Susanne C; Emborg, Jørgen; Andersen, Tom

    1996-01-01

    The paper reports on a prototype developed as to demonstrate the (dis)abilities of the OLE-standard to integrate different design-applications to a CAD-syste.......The paper reports on a prototype developed as to demonstrate the (dis)abilities of the OLE-standard to integrate different design-applications to a CAD-syste....

  15. GATEWAY Demonstrations: OLED Lighting in the Offices of DeJoy, Knauf & Blood, LLP

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Naomi J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2017-07-24

    At the offices of the accounting firm of DeJoy, Knauf & Blood, LLP in Rochester, NY, the GATEWAY program evaluated a new lighting system that incorporates a number of different OLED luminaires. Evaluation of the OLED products included efficacy performance, field measurements of panel color, flicker measurements, and staff feedback.

  16. Life prediction of OLED for constant-stress accelerated degradation tests using luminance decaying model

    International Nuclear Information System (INIS)

    Zhang, Jianping; Li, Wenbin; Cheng, Guoliang; Chen, Xiao; Wu, Helen; Herman Shen, M.-H.

    2014-01-01

    In order to acquire the life information of organic light emitting diode (OLED), three groups of constant stress accelerated degradation tests are performed to obtain the luminance decaying data of samples under the condition that the luminance and the current are respectively selected as the indicator of performance degradation and the test stress. Weibull function is applied to describe the relationship between luminance decaying and time, least square method (LSM) is employed to calculate the shape parameter and scale parameter, and the life prediction of OLED is achieved. The numerical results indicate that the accelerated degradation test and the luminance decaying model reveal the luminance decaying law of OLED. The luminance decaying formula fits the test data very well, and the average error of fitting value compared with the test data is small. Furthermore, the accuracy of the OLED life predicted by luminance decaying model is high, which enable rapid estimation of OLED life and provide significant guidelines to help engineers make decisions in design and manufacturing strategy from the aspect of reliability life. - Highlights: • We gain luminance decaying data by accelerated degradation tests on OLED. • The luminance decaying model objectively reveals the decaying law of OLED luminance. • The least square method (LSM) is employed to calculate Weibull parameters. • The plan designed for accelerated degradation tests proves to be feasible. • The accuracy of the OLED life and the luminance decaying fitting formula is high

  17. An imaging-based photometric and colorimetric measurement method for characterizing OLED panels for lighting applications

    Science.gov (United States)

    Zhu, Yiting; Narendran, Nadarajah; Tan, Jianchuan; Mou, Xi

    2014-09-01

    The organic light-emitting diode (OLED) has demonstrated its novelty in displays and certain lighting applications. Similar to white light-emitting diode (LED) technology, it also holds the promise of saving energy. Even though the luminous efficacy values of OLED products have been steadily growing, their longevity is still not well understood. Furthermore, currently there is no industry standard for photometric and colorimetric testing, short and long term, of OLEDs. Each OLED manufacturer tests its OLED panels under different electrical and thermal conditions using different measurement methods. In this study, an imaging-based photometric and colorimetric measurement method for OLED panels was investigated. Unlike an LED that can be considered as a point source, the OLED is a large form area source. Therefore, for an area source to satisfy lighting application needs, it is important that it maintains uniform light level and color properties across the emitting surface of the panel over a long period. This study intended to develop a measurement procedure that can be used to test long-term photometric and colorimetric properties of OLED panels. The objective was to better understand how test parameters such as drive current or luminance and temperature affect the degradation rate. In addition, this study investigated whether data interpolation could allow for determination of degradation and lifetime, L70, at application conditions based on the degradation rates measured at different operating conditions.

  18. Study on luminescence characteristics of blue OLED with phosphor-doped host-guest structure

    Science.gov (United States)

    Wang, Zhen; Liu, Fei; Zheng, Xin; Chen, Ai; Xie, Jia-feng; Zhang, Wen-xia

    2018-05-01

    In this study, we design and fabricate phosphor-doped host-guest structure organic light-emitting diodes (OLEDs), where the blue-ray iridium complex electrophosphorescent material FIrpic acts as object material. Properties of the device can be accommodated by changing the host materials, dopant concentration and thickness of the light-emitting layer. The study shows that the host material N,N'-dicarbazolyl-3,5-benzene (mCP) has a higher triplet excited state energy level, which can effectively prevent FIrpic triplet excited state energy backtracking to host material, thus the luminous efficiency is improved. When mCP is selected as the host material, the thickness of the light-emitting layer is 30 nm and the dopant concentration is 8 wt%, the excitons can be effectively confined in the light-emitting region. As a result, the maximum current efficiency and the maximum brightness of the blue device can reach 15.5 cd/A and 7 196.3 cd/m2, respectively.

  19. BODIPY associates in organic matrices: Spectral properties, photostability and evaluation as OLED emitters

    Energy Technology Data Exchange (ETDEWEB)

    Merkushev, D.A.; Usoltsev, S.D. [Ivanovo State University of Chemistry and Technology, Sheremetevskiy Avenue 7, 153000 Ivanovo (Russian Federation); Marfin, Yu.S., E-mail: marfin@isuct.ru [Ivanovo State University of Chemistry and Technology, Sheremetevskiy Avenue 7, 153000 Ivanovo (Russian Federation); Pushkarev, A.P., E-mail: pushkarev@iomc.ras.ru [G.A. Razuvaev Institute of Organometallic Chemistry RAS, Tropinina 49, 603950 Nizhny Novgorod (Russian Federation); Volyniuk, D.; Grazulevicius, J.V. [Department of Polymer Chemistry and Technology, Kaunas University of Technology, Radvilenu pl. 19, LT-50254 Kaunas (Lithuania); Rumyantsev, E.V. [Ivanovo State University of Chemistry and Technology, Sheremetevskiy Avenue 7, 153000 Ivanovo (Russian Federation)

    2017-02-01

    In the present study four BODIPY (boron dipyrromethene: 4,4-difluoro-4-bora-3a,4a-diaza-s-indacene) dyes with π-extended substituents in C-8 position were investigated in solvents and polymer mediums. High aggregation degree was observed for the dyes in the solid state. Association and twisted intramolecular charge transfer processes were found to affect the spectral properties of the compounds causing bathochromic shifts in absorption and fluorescence spectra. The extension of substituent π-conjugation gains molecular association evoked presumably by π-π interaction between the substituents of the adjacent molecules. Photostability of the complexes in different forms was analyzed and the distorted form stabilized by polymer matrix was found to be the most stable. The substituent nature did not affect strongly the photostability of dyes. Displacement of monomer-associate equilibrium in hybrid materials with polymethylmethacrylate and poly(9-vinylcarbazole) was exploited for tuning spectral characteristics of the materials. Two dyes readily forming aggregates at the lowest concentrations were applied for the fabrication of organic light-emitting diodes. The fabricated devices exhibited electroluminescence in the appropriate spectral ranges with moderate efficiency. - Highlights: • Four BODIPY dyes with π-extended substituents in 8-position were investigated in solvents and polymers. • Substituent influence on photophysical properties and photostability of the compounds are discussed. • Aggregation induced spectral changes were observed. • Displacement of monomer-aggregate equilibrium was exploited for tuning electroluminescent characteristics of OLED devices.

  20. Electron injection mechanisms of green organic light-emitting devices fabricated utilizing a double electron injection layer consisting of cesium carbonate and fullerene

    International Nuclear Information System (INIS)

    Yang, J.S.; Choo, D.C.; Kim, T.W.; Jin, Y.Y.; Seo, J.H.; Kim, Y.K.

    2010-01-01

    Electron injection mechanisms of the luminance efficiency of green organic light-emitting devices (OLEDs) fabricated utilizing a cesium carbonate (Cs 2 CO 3 )/fullerene (C 60 ) heterostructure acting as an electron injection layer (EIL) were investigated. Current density-voltage and luminance-voltage measurements showed that the current densities and the luminances of the OLEDs with a Cs 2 CO 3 or Cs 2 CO 3 /C 60 EIL were higher than that of the OLEDs with a Liq EIL. The luminance efficiency of the OLEDs with a Cs 2 CO 3 EIL was almost three times higher than that of the OLEDs with a Liq EIL. Because the electron injection efficiency of the Cs 2 CO 3 layer in OLEDs was different from that of the C 60 layer, the luminance efficiency of the OLEDs with a double EIL consisting of a Cs 2 CO 3 layer and a C 60 layer was smaller than that of the OLEDs with a Cs 2 CO 3 EIL. The electron injection mechanisms of OLEDs with a Cs 2 CO 3 and C 60 double EIL are described on the basis of the experimental results.

  1. Reframing information architecture

    CERN Document Server

    Resmini, Andrea

    2014-01-01

    Information architecture has changed dramatically since the mid-1990s and earlier conceptions of the world and the internet being different and separate have given way to a much more complex scenario in the present day. In the post-digital world that we now inhabit the digital and the physical blend easily and our activities and usage of information takes place through multiple contexts and via multiple devices and unstable, emergent choreographies. Information architecture now is steadily growing into a channel- or medium-specific multi-disciplinary framework, with contributions coming from a

  2. Computing architecture for autonomous microgrids

    Science.gov (United States)

    Goldsmith, Steven Y.

    2015-09-29

    A computing architecture that facilitates autonomously controlling operations of a microgrid is described herein. A microgrid network includes numerous computing devices that execute intelligent agents, each of which is assigned to a particular entity (load, source, storage device, or switch) in the microgrid. The intelligent agents can execute in accordance with predefined protocols to collectively perform computations that facilitate uninterrupted control of the .

  3. Dependence of surface morphology on molecular structure and its influence on the properties of OLEDs

    Energy Technology Data Exchange (ETDEWEB)

    Lim, S.H. [Department of Chemical Engineering, Hongik University, 72-1, Sangsu-Dong, Mapo-Gu, Seoul 121-791 (Korea, Republic of); Ryu, G.Y. [Department of Electric Information and Control Engineering, Hongik University, 72-1, Sangsu-Dong, Mapo-Gu, Seoul 121-791 (Korea, Republic of); Seo, J.H.; Park, J.H. [Center for Organic Materials and Information Devices (COMID), Hongik University, 72-1, Sangsu-Dong, Mapo-Gu, Seoul 121-791 (Korea, Republic of); Department of Information Display, Hongik University, 72-1, Sangsu-Dong, Mapo-Gu, Seoul 121-791 (Korea, Republic of); Youn, S.W. [Department of Chemical Engineering, Hongik University, 72-1, Sangsu-Dong, Mapo-Gu, Seoul 121-791 (Korea, Republic of); Kim, Y.K. [Center for Organic Materials and Information Devices (COMID), Hongik University, 72-1, Sangsu-Dong, Mapo-Gu, Seoul 121-791 (Korea, Republic of); Department of Information Display, Hongik University, 72-1, Sangsu-Dong, Mapo-Gu, Seoul 121-791 (Korea, Republic of); Shin, D.M. [Department of Chemical Engineering, Hongik University, 72-1, Sangsu-Dong, Mapo-Gu, Seoul 121-791 (Korea, Republic of)], E-mail: shindm@wow.hongik.ac.kr

    2008-09-15

    Most organic light-emitting diodes (OLEDs) have a multilayer structure composed of organic layers such as a hole injection layer (HIL), a hole transport layer (HTL), an emission layer (EML), an electron transport layer (ETL) and an electron injection layer (EIL) sandwiched between two electrodes. The organic layers are thin solid films with a thickness from a few nano meters to a few tenths nano meter, respectively. Surface morphology of an organic thin solid film in OLEDs depends on the molecular structure of the organic material and has an affect on device performance. To analyze the effect of surface morphology of an organic thin solid film on fluorescence and electroluminescence (EL) properties, thin solid films of 4-(dicyanomethylene)-2-methyl-6-(julolidin-4-yl-vinyl)-4H-pyran (DCM2) and new red fluorophores, (2E,2'E)-3,3'-[4,4''-bis(dimethylamino)-1,1':4',1''-terphenyl-2',5'-diyl] bis[2= -(2-thienyl)acrylonitrile] (ABCV-Th) and (2Z,2'Z)-3,3'-[4,4''-bis(dimethylamino)-1,1':4',1''-terphenyl-2',5'-diyl] bis(2-phenylacrylonitrile) (ABCV-P) were investigated by atomic force microscopy (AFM). The samples for EL and AFM measurement were fabricated by the high-vacuum thermal deposition (8x10{sup -7} Torr) of organic materials onto the surface of indium tin oxide (ITO)-coated glass substrate, in which the layer structures of samples for AFM measurement and those for EL measurement were ITO/NPB (40 nm)/red emitters (80 nm) and ITO/NPB (40 nm)/red emitters (80 nm)/BCP (30 nm)/Liq (2 nm)/Al (100 nm), respectively. The analysis based on AFM measurements well supported that the photoluminescence properties and the device performance were very much dependent upon surface morphology of an organic thin layer.

  4. Architectural Contestation

    NARCIS (Netherlands)

    Merle, J.

    2012-01-01

    This dissertation addresses the reductive reading of Georges Bataille's work done within the field of architectural criticism and theory which tends to set aside the fundamental ‘broken’ totality of Bataille's oeuvre and also to narrowly interpret it as a mere critique of architectural form,

  5. Architecture Sustainability

    NARCIS (Netherlands)

    Avgeriou, Paris; Stal, Michael; Hilliard, Rich

    2013-01-01

    Software architecture is the foundation of software system development, encompassing a system's architects' and stakeholders' strategic decisions. A special issue of IEEE Software is intended to raise awareness of architecture sustainability issues and increase interest and work in the area. The

  6. Memory architecture

    NARCIS (Netherlands)

    2012-01-01

    A memory architecture is presented. The memory architecture comprises a first memory and a second memory. The first memory has at least a bank with a first width addressable by a single address. The second memory has a plurality of banks of a second width, said banks being addressable by components

  7. Architectural Narratives

    DEFF Research Database (Denmark)

    Kiib, Hans

    2010-01-01

    a functional framework for these concepts, but tries increasingly to endow the main idea of the cultural project with a spatially aesthetic expression - a shift towards “experience architecture.” A great number of these projects typically recycle and reinterpret narratives related to historical buildings......In this essay, I focus on the combination of programs and the architecture of cultural projects that have emerged within the last few years. These projects are characterized as “hybrid cultural projects,” because they intend to combine experience with entertainment, play, and learning. This essay...... and architectural heritage; another group tries to embed new performative technologies in expressive architectural representation. Finally, this essay provides a theoretical framework for the analysis of the political rationales of these projects and for the architectural representation bridges the gap between...

  8. Analysis of the current-voltage characteristics of polymer-based organic light-emitting diodes (OLEDs deposited by spin coating

    Directory of Open Access Journals (Sweden)

    Ricardo Vera

    2010-04-01

    Full Text Available Polymer-based organic light-emitting diodes (OLEDs with the structure ITO / PEDOT:PSS / MDMO-PPV / Metal were prepared by spincoating. It is known that electroluminescence of these devices is strongly dependent on the material used as cathode and on the depositionparameters of the polymer electroluminescent layer MDMO-PPV. Objective. In this work the effect of i the frequency of the spin coater(1000-8000 rpm, ii the concentration of the MDMO-PPV: Toluene solution, and iii the material used as cathode (Aluminium or Silveron the electrical response of the devices, was evaluated through current-voltage (I-V measurements. Materials and methods. PEDOT:PPSand MDMO-PPV organic layers were deposited by spin coating on ITO substrates, and the OLED structure was completed with cathodesof aluminium and silver. The electric response of the devices was evaluated based on the I-V characteristics. Results. Diodes prepared withthinner organic films allow higher currents at lower voltages; this can be achieved either by increasing the frequency of the spin coater orby using concentrations of MDMO-PPV: Toluene lower than 2% weight. A fit of the experimental data showed that the diodes have twocontributions to the current. The first one is attributed to parasitic currents between anode and cathode, and the other one is a parallel currentthrough the organic layer, in which the carrier injection mechanism is mediated by thermionic emission. Conclusions. The results of thefitting and the energy level alignment through the whole structure show that PPV-based OLEDs are unipolar devices, with current mainlyattributed to hole transport.

  9. IMPLEMENTATION OF TRANSMITTER AND RECEIVER ARCHITECTURE FOR PHYSICAL HYBRID INDICATOR CHANNEL OF LTE-ADVANCED USING PARTIAL RECONFIGURATION IN ML605 VIRTEX-6 DEVICE

    Directory of Open Access Journals (Sweden)

    S. Syed Ameer Abbas

    2014-09-01

    Full Text Available LTE-A (Long Term Evolution-Advanced is the fourth generation technology to increase the speed of wireless data network. The LTE-A Physical layer provides both data and control information between an enhanced base station and mobile user equipment which is quite complex and consists of a mixture of technologies. Since there is requirement for more resources to accommodate all the channels in a single FPGA, Partial Reconfiguration (PR technique is introduced to configure the total hardware into sub modules that configure and operate in different instants of time. PR enables a part of FPGA to be reconfigured, while the rest continues to function without any interruptions and reduces the hardware resource power and fabric area. This work proposes the realization of transmitter and receiver architecture of Physical Hybrid Indicator Channel (PHICH channel for LTE-A using partial reconfiguration on xc6vlx240tff1156-1 FPGA. The receiver architecture for PHICH is to report the correct reception of uplink user data to the User Equipment (UE in the form of Acknowledgment (ACK, or Negative ACK (NACK in a 1 millisecond duration sub-frame of Long Term Evolution (LTE System. The modules for the different diversities are reconfigured based on the control signals from the transmitter.

  10. Organic Optical Sensor Based on Monolithic Integration of Organic Electronic Devices

    Directory of Open Access Journals (Sweden)

    Hoi Lam Tam

    2015-09-01

    Full Text Available A novel organic optical sensor that integrates a front organic light-emitting diode (OLED and an organic photodiode (OPD is demonstrated. The stripe-shaped cathode is used in the OLED components to create light signals, while the space between the stripe-shaped cathodes serves as the detection window for integrated OPD units. A MoO3 (5 nm/Ag (15 nm bi-layer inter-electrode is interposed between the vertically stacked OLED and OPD units, serving simultaneously as the cathode for the front OLED and an anode for the upper OPD units in the sensor. In the integrated sensor, the emission of the OLED units is confined by the area of the opaque stripe-shaped cathodes, optimized to maximize the reflected light passing through the window space for detection by the OPD components. This can ensure high OLED emission output, increasing the signal/noise ratio. The design and fabrication flexibility of an integrated OLED/OPD device also has low cost benefits, and is light weight and ultra-thin, making it possible for application in wearable units, finger print identification, image sensors, smart light sources, and compact information systems.

  11. Ole Ivar Lovaas - His Life, Merits and Legacy

    Directory of Open Access Journals (Sweden)

    Kamil ÖZERK

    2016-12-01

    Full Text Available Ole Ivar Lovaas (1927-2010 is known worldwide for his research within the field of Applied Behavior Analysis, and is probably the most influential researcher within the field of treatment of children with autism. In the first part of this biographically oriented paper, we inform the readers about his family background, childhood, elementary and secondary school years, and his adolescent years during World War II in his first homeland, Norway, based on archival research and interviews. In the second part, we describe his life, academic studies, research and successes in his second home country, the United States. Finally, we briefly recount the impact Lovaas has had on the field of Applied Behavior Analysis and the treatment of and services for children with autism spectrum disorders in Norway and in the North America.

  12. Display process compatible accurate graphene patterning for OLED applications

    Science.gov (United States)

    Shin, Jin-Wook; Han, Jun-Han; Cho, Hyunsu; Moon, Jaehyun; Kwon, Byoung-Hwa; Cho, Seungmin; Yoon, Taeshik; Kim, Taek-Soo; Suemitsu, Maki; Lee, Jeong-Ik; Cho, Nam Sung

    2018-01-01

    Graphene film can be used as transparent electrodes in display and optoelectronic applications. However, achieving residue free graphene film pixel arrays with geometrical precision on large area has been a difficult challenge. By utilizing the liquid bridging concept, we realized photolithographic patterning of graphene film with dimensional correctness and absence of surface contaminant. On a glass substrate of 100  ×  100 mm2 size, we demonstrate our patterning method to fabricate an addressable two-color OLED module of which graphene film pixel size is 170  ×  300 µm2. Our results strongly suggest graphene film as a serviceable component in commercial display products. The flexible and foldable display applications are expected to be main beneficiaries of our method.

  13. Agricultural activities in the Oleśnica commune

    Directory of Open Access Journals (Sweden)

    Małgorzata Borkowska

    2009-01-01

    Full Text Available The aim of the study was to analyse and assess the agricultural activity in the Oleśnica commune. The representative rural property owner was a secondary-educated 43-year old man. Over 70% of respondents demonstrated their willingness to expand by purchasing or renting land and also to develop infrastructure. Agricultural activities within this area were focused mainly on plant-growing, which was preferable due to sustained tide of the market. Arable land was the dominating land type and the main products were: grains, potatoes and rape. Introduced in farms innovations were focused on increasing ef-fectiveness of plant-growing and improving the quality of work in rural properties. These innovations were expected to increase income and, in longer term, make the rural production more competitive on the European market.

  14. Architectural technology

    DEFF Research Database (Denmark)

    2005-01-01

    The booklet offers an overall introduction to the Institute of Architectural Technology and its projects and activities, and an invitation to the reader to contact the institute or the individual researcher for further information. The research, which takes place at the Institute of Architectural...... Technology at the Roayl Danish Academy of Fine Arts, School of Architecture, reflects a spread between strategic, goal-oriented pilot projects, commissioned by a ministry, a fund or a private company, and on the other hand projects which originate from strong personal interests and enthusiasm of individual...

  15. Systemic Architecture

    DEFF Research Database (Denmark)

    Poletto, Marco; Pasquero, Claudia

    -up or tactical design, behavioural space and the boundary of the natural and the artificial realms within the city and architecture. A new kind of "real-time world-city" is illustrated in the form of an operational design manual for the assemblage of proto-architectures, the incubation of proto-gardens...... and the coding of proto-interfaces. These prototypes of machinic architecture materialize as synthetic hybrids embedded with biological life (proto-gardens), computational power, behavioural responsiveness (cyber-gardens), spatial articulation (coMachines and fibrous structures), remote sensing (FUNclouds...

  16. Humanizing Architecture

    DEFF Research Database (Denmark)

    Toft, Tanya Søndergaard

    2015-01-01

    The article proposes the urban digital gallery as an opportunity to explore the relationship between ‘human’ and ‘technology,’ through the programming of media architecture. It takes a curatorial perspective when proposing an ontological shift from considering media facades as visual spectacles...... agency and a sense of being by way of dematerializing architecture. This is achieved by way of programming the symbolic to provide new emotional realizations and situations of enlightenment in the public audience. This reflects a greater potential to humanize the digital in media architecture....

  17. Highly efficient blue OLEDs based on diphenylaminofluorenylstyrenes end-capped with heterocyclic aromatics

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Suhyun [Department of Chemistry, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Lee, Kum Hee; Kim, Young Kwan [Department of Information Display, Hongik University, Seoul 121-791 (Korea, Republic of); Yoon, Seung Soo, E-mail: ssyoon@skku.edu [Department of Chemistry, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of)

    2012-10-15

    In this paper, we have designed four diphenylaminofluorenylstyrene derivatives end-capped with heterocyclic aromatic groups, such as 9-phenylcabazole, 4-dibenzofuran, 2-benzoxazole, 2-quinoxaline, respectively. These materials showed blue to red fluorescence with maximum emission wavelengths of 476–611 nm, respectively, which were dependent on the structural and electronic nature of end-capping groups. To explore the electroluminescent properties of these materials, multilayer OLEDs were fabricated in the following sequence: ITO/DNTPD (40 nm)/NPB (20 nm)/2% doped in MADN (20 nm)/Alq{sub 3} (40 nm)/Liq. (1 nm)/Al. Among those, a device exhibited a highly efficient blue emission with the maximum luminance of 14,480 cd/m{sup 2} at 9 V, the luminous efficiency of 5.38 cd/A at 20 mA/cm{sup 2}, power efficiency of 2.77 lm/W at 20 mA/cm{sup 2}, and CIE{sub x,y} coordinates of (0.147, 0.152) at 8 V, respectively.

  18. Synthesis and characterization of germane/stannane-capped polysiloles for the fabrication of luminescent OLED.

    Science.gov (United States)

    Kim, Myoung-Hee; Woo, Hee-Gweon; Kim, Whan Gi; Cho, Myong-Shik

    2009-12-01

    Dehydropolymerization (with various inorganic hydrides) and subsequent germane/stannane-capping (with Me2GeHCI and Ph2SnHCI) of 1,1-dihydrotetraphenylsilole (1) give electroluminescent germane/stannane-capped polysiloles (2) in high yield. The polymerization yield and molecular weight with Selectride increase in the order L-Selectride < N-Selectride < K-Selectride. The molecular weights increase in the order Red-Al < K-Selectride < Super Hydride. The germane/stannane-capped polysiloles 2 emit at 521 nm and are electroluminescent at 522 nm. The fluorescence quantum yield of 2 in toluene is (1.66 +/- 0.26) x 10(-2). The emission color is green and the maximum brightness of the device is 2,800 cd/m2 with a luminous efficiency of 0.68 lm/W. The type of end group exhibited no appreciable effect on the luminescent properties of polysilole backbone. Thus, the germane/stannane-capped polysiloles are found to be a good material for OLED fabrication.

  19. Architectural Theatricality

    DEFF Research Database (Denmark)

    Tvedebrink, Tenna Doktor Olsen

    environments and a knowledge gap therefore exists in present hospital designs. Consequently, the purpose of this thesis has been to investigate if any research-based knowledge exist supporting the hypothesis that the interior architectural qualities of eating environments influence patient food intake, health...... and well-being, as well as outline a set of basic design principles ‘predicting’ the future interior architectural qualities of patient eating environments. Methodologically the thesis is based on an explorative study employing an abductive approach and hermeneutic-interpretative strategy utilizing tactics...... and food intake, as well as a series of references exist linking the interior architectural qualities of healthcare environments with the health and wellbeing of patients. On the basis of these findings, the thesis presents the concept of Architectural Theatricality as well as a set of design principles...

  20. Layered architecture for quantum computing

    OpenAIRE

    Jones, N. Cody; Van Meter, Rodney; Fowler, Austin G.; McMahon, Peter L.; Kim, Jungsang; Ladd, Thaddeus D.; Yamamoto, Yoshihisa

    2010-01-01

    We develop a layered quantum-computer architecture, which is a systematic framework for tackling the individual challenges of developing a quantum computer while constructing a cohesive device design. We discuss many of the prominent techniques for implementing circuit-model quantum computing and introduce several new methods, with an emphasis on employing surface-code quantum error correction. In doing so, we propose a new quantum-computer architecture based on optical control of quantum dot...

  1. Study on scalable Coulombic degradation for estimating the lifetime of organic light-emitting devices

    International Nuclear Information System (INIS)

    Zhang Wenwen; Hou Xun; Wu Zhaoxin; Liang Shixiong; Jiao Bo; Zhang Xinwen; Wang Dawei; Chen Zhijian; Gong Qihuang

    2011-01-01

    The luminance decays of organic light-emitting diodes (OLEDs) are investigated with initial luminance of 1000 to 20 000 cd m -2 through a scalable Coulombic degradation and a stretched exponential decay. We found that the estimated lifetime by scalable Coulombic degradation deviates from the experimental results when the OLEDs work with high initial luminance. By measuring the temperature of the device during degradation, we found that the higher device temperatures will lead to instabilities of organic materials in devices, which is expected to result in the difference between the experimental results and estimation using the scalable Coulombic degradation.

  2. Theoretical investigation of the degradation mechanisms in host and guest molecules used in OLED active layers

    KAUST Repository

    Winget, Paul; Hong, Minki; Bredas, Jean-Luc

    2014-01-01

    systems. We identify degradation pathways and define new strategies to guide the synthesis of stable materials for OLED applications for both phosphorescent emitters and organic host materials. The chemical reactivity of these molecules in the active

  3. Kuu plaat : Lauri Saatpalu ja Katrin Mandel "Sa oled hea". Plaadid kauplusest Lasering

    Index Scriptorium Estoniae

    2005-01-01

    Heliplaatidest: Lauri Saatpalu ja Katrin Mandel "Sa oled hea", Goldfrapp "Supernature", Ultima Thule "Ingel ja suli", Sigur Ros "Takk...", Franz Ferdinand "You Could Have It So Much Better", Ans.Andur "Tuled peale"

  4. Jumal tänatud, et sa siin oled! / Inge Pitsner

    Index Scriptorium Estoniae

    Pitsner, Inge

    2007-01-01

    Kanal 2 sketshishõude sarja "Jumal tänatud, et sa siin oled!" esimesest saatest : saatejuht Andrus Vaarik : osalejad Peeter Oja, Anu Saagim, Juhan Ulfsak, Mihkel Raud : kohtunik Eino Baskin : tootjafirma Ruut

  5. Phosphorescent Organic Light-Emitting Devices: Working Principle and Iridium Based Emitter Materials

    Directory of Open Access Journals (Sweden)

    Emil J. W. List

    2008-08-01

    Full Text Available Even though organic light-emitting device (OLED technology has evolved to a point where it is now an important competitor to liquid crystal displays (LCDs, further scientific efforts devoted to the design, engineering and fabrication of OLEDs are required for complete commercialization of this technology. Along these lines, the present work reviews the essentials of OLED technology putting special focus on the general working principle of single and multilayer OLEDs, fluorescent and phosphorescent emitter materials as well as transfer processes in host materials doped with phosphorescent dyes. Moreover, as a prototypical example of phosphorescent emitter materials, a brief discussion of homo- and heteroleptic iridium(III complexes is enclosed concentrating on their synthesis, photophysical properties and approaches for realizing iridium based phosphorescent polymers.

  6. In plane optical sensor based on organic electronic devices

    NARCIS (Netherlands)

    Koetse, M.M; Rensing, P.A.; Heck, G.T. van; Sharpe, R.B.A.; Allard, B.A.M.; Wieringa, F.P.; Kruijt, P.G.M.; Meulendijks, N.M.M.; Jansen, H.; Schoo, H.F.M.

    2008-01-01

    Sensors based on organic electronic devices are emerging in a wide range of application areas. Here we present a sensor platform using organic light emitting diodes (OLED) and organic photodiodes (OPD) as active components. By means of lamination and interconnection technology the functional foils

  7. Architectural freedom and industrialized architecture

    DEFF Research Database (Denmark)

    Vestergaard, Inge

    2012-01-01

    to explain that architecture can be thought as a complex and diverse design through customization, telling exactly the revitalized storey about the change to a contemporary sustainable and better performing expression in direct relation to the given context. Through the last couple of years we have...... proportions, to organize the process on site choosing either one room wall components or several rooms wall components – either horizontally or vertically. Combined with the seamless joint the playing with these possibilities the new industrialized architecture can deliver variations in choice of solutions...... for retrofit design. If we add the question of the installations e.g. ventilation to this systematic thinking of building technique we get a diverse and functional architecture, thereby creating a new and clearer story telling about new and smart system based thinking behind architectural expression....

  8. Architectural freedom and industrialized architecture

    DEFF Research Database (Denmark)

    Vestergaard, Inge

    2012-01-01

    to explain that architecture can be thought as a complex and diverse design through customization, telling exactly the revitalized storey about the change to a contemporary sustainable and better performing expression in direct relation to the given context. Through the last couple of years we have...... expression in the specific housing area. It is the aim of this article to expand the different design strategies which architects can use – to give the individual project attitudes and designs with architectural quality. Through the customized component production it is possible to choose different...... for retrofit design. If we add the question of the installations e.g. ventilation to this systematic thinking of building technique we get a diverse and functional architecture, thereby creating a new and clearer story telling about new and smart system based thinking behind architectural expression....

  9. Architectural freedom and industrialised architecture

    DEFF Research Database (Denmark)

    Vestergaard, Inge

    2012-01-01

    Architectural freedom and industrialized architecture. Inge Vestergaard, Associate Professor, Cand. Arch. Aarhus School of Architecture, Denmark Noerreport 20, 8000 Aarhus C Telephone +45 89 36 0000 E-mai l inge.vestergaard@aarch.dk Based on the repetitive architecture from the "building boom" 1960...... customization, telling exactly the revitalized storey about the change to a contemporary sustainable and better performed expression in direct relation to the given context. Through the last couple of years we have in Denmark been focusing a more sustainable and low energy building technique, which also include...... to the building physic problems a new industrialized period has started based on light weight elements basically made of wooden structures, faced with different suitable materials meant for individual expression for the specific housing area. It is the purpose of this article to widen up the different design...

  10. Photovoltaic OLED Driver for Low-Power Stand-Alone Light-to-Light Systems

    DEFF Research Database (Denmark)

    Ploug, Rasmus Overgaard; Knott, Arnold

    2016-01-01

    of a three-port-converter for this purpose optimized for the specifications for driving an Organic Light Emitting Diode (OLED) panel intended for lighting purposes. By using a three-port-converter, featuring shared components for each conversion mode, the converter reaches 97 % efficiency at 1.8 W during...... conversion from photovoltaic panel to the battery, and 97 % in the area 1.4 W to 2 W for power delivery to the OLED....

  11. Multi-Periodic Photonic Crystal Out-Coupling Layers for Flexible OLEDs

    DEFF Research Database (Denmark)

    Kluge, Christian; Pradana, Arfat; Adam, Jost

    2014-01-01

    Waveguide mode extraction with multi-periodic photonic crystals is studied in experiment and finite-difference time-domain (FDTD) simulations. Flexible nanostructured organic light-emitting diodes (OLEDs) are fabricated by UV nanoimprint lithography.......Waveguide mode extraction with multi-periodic photonic crystals is studied in experiment and finite-difference time-domain (FDTD) simulations. Flexible nanostructured organic light-emitting diodes (OLEDs) are fabricated by UV nanoimprint lithography....

  12. GATEWAY Report Brief: OLED Lighting in the Offices of Aurora Lighting Design, Inc.

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2016-05-31

    Summary of a GATEWAY report evaluation at the offices of Aurora Lighting Design, Inc., in Grayslake, IL, where the GATEWAY program conducted its first investigation involving OLED lighting. The project experienced several challenges, but also highlighted a number of promising attributes – which indicate that with continued improvements in efficacy, longevity, size, and flexibility, OLEDs could provide a new tool for creative and effective lighting.

  13. PICNIC Architecture.

    Science.gov (United States)

    Saranummi, Niilo

    2005-01-01

    The PICNIC architecture aims at supporting inter-enterprise integration and the facilitation of collaboration between healthcare organisations. The concept of a Regional Health Economy (RHE) is introduced to illustrate the varying nature of inter-enterprise collaboration between healthcare organisations collaborating in providing health services to citizens and patients in a regional setting. The PICNIC architecture comprises a number of PICNIC IT Services, the interfaces between them and presents a way to assemble these into a functioning Regional Health Care Network meeting the needs and concerns of its stakeholders. The PICNIC architecture is presented through a number of views relevant to different stakeholder groups. The stakeholders of the first view are national and regional health authorities and policy makers. The view describes how the architecture enables the implementation of national and regional health policies, strategies and organisational structures. The stakeholders of the second view, the service viewpoint, are the care providers, health professionals, patients and citizens. The view describes how the architecture supports and enables regional care delivery and process management including continuity of care (shared care) and citizen-centred health services. The stakeholders of the third view, the engineering view, are those that design, build and implement the RHCN. The view comprises four sub views: software engineering, IT services engineering, security and data. The proposed architecture is founded into the main stream of how distributed computing environments are evolving. The architecture is realised using the web services approach. A number of well established technology platforms and generic standards exist that can be used to implement the software components. The software components that are specified in PICNIC are implemented in Open Source.

  14. Architectural freedom and industrialised architecture

    DEFF Research Database (Denmark)

    Vestergaard, Inge

    2012-01-01

    to the building physic problems a new industrialized period has started based on light weight elements basically made of wooden structures, faced with different suitable materials meant for individual expression for the specific housing area. It is the purpose of this article to widen up the different design...... to this systematic thinking of the building technique we get a diverse and functional architecture. Creating a new and clearer story telling about new and smart system based thinking behind the architectural expression....

  15. Simultaneous Enhancement of Efficiency and Stability of Phosphorescent OLEDs Based on Efficient Förster Energy Transfer from Interface Exciplex.

    Science.gov (United States)

    Zhang, Dongdong; Cai, Minghan; Zhang, Yunge; Bin, Zhengyang; Zhang, Deqiang; Duan, Lian

    2016-02-17

    Exciplex forming cohosts have been widely adopted in phosphorescent organic light-emitting diodes (PHOLEDs), achieving high efficiency with low roll-off and low driving voltage. However, the influence of the exciplex-forming hosts on the lifetimes of the devices, which is one of the essential characteristics, remains unclear. Here, we compare the influence of the bulk exciplex and interface exciplex on the performances of the devices, demonstrating highly efficient orange PHOLEDs with long lifetime at low dopant concentration by efficient Förster energy transfer from the interface exciplex. A bipolar host, (3'-(4,6-diphenyl-1,3,5-triazin-2-yl)-(1,1'-biphenyl)-3-yl)-9-carbazole (CzTrz), was adopted to combine with a donor molecule, tris(4-(9H-carbazol-9-yl)phenyl)amine (TCTA), to form exciplex. Devices with energy transfer from the interface exciplex achieve lifetime almost 2 orders of magnitude higher than the ones based on bulk exciplex as the host by avoiding the formation of the donor excited states. Moreover, a highest EQE of 27% was obtained at the dopant concentration as low as 3 wt % for a device with interface exciplex, which is favorable for reducing the cost of fabrication. We believe that our work may shed light on future development of ideal OLEDs with high efficiency, long-lifetime, low roll-off and low cost simultaneously.

  16. Organic electronic devices using phthalimide compounds

    Science.gov (United States)

    Hassan, Azad M.; Thompson, Mark E.

    2010-09-07

    Organic electronic devices comprising a phthalimide compound. The phthalimide compounds disclosed herein are electron transporters with large HOMO-LUMO gaps, high triplet energies, large reduction potentials, and/or thermal and chemical stability. As such, these phthalimide compounds are suitable for use in any of various organic electronic devices, such as OLEDs and solar cells. In an OLED, the phthalimide compounds may serve various functions, such as a host in the emissive layer, as a hole blocking material, or as an electron transport material. In a solar cell, the phthalimide compounds may serve various functions, such as an exciton blocking material. Various examples of phthalimide compounds which may be suitable for use in the present invention are disclosed.

  17. Architectural geometry

    KAUST Repository

    Pottmann, Helmut; Eigensatz, Michael; Vaxman, Amir; Wallner, Johannes

    2014-01-01

    Around 2005 it became apparent in the geometry processing community that freeform architecture contains many problems of a geometric nature to be solved, and many opportunities for optimization which however require geometric understanding. This area of research, which has been called architectural geometry, meanwhile contains a great wealth of individual contributions which are relevant in various fields. For mathematicians, the relation to discrete differential geometry is significant, in particular the integrable system viewpoint. Besides, new application contexts have become available for quite some old-established concepts. Regarding graphics and geometry processing, architectural geometry yields interesting new questions but also new objects, e.g. replacing meshes by other combinatorial arrangements. Numerical optimization plays a major role but in itself would be powerless without geometric understanding. Summing up, architectural geometry has become a rewarding field of study. We here survey the main directions which have been pursued, we show real projects where geometric considerations have played a role, and we outline open problems which we think are significant for the future development of both theory and practice of architectural geometry.

  18. Architectural geometry

    KAUST Repository

    Pottmann, Helmut

    2014-11-26

    Around 2005 it became apparent in the geometry processing community that freeform architecture contains many problems of a geometric nature to be solved, and many opportunities for optimization which however require geometric understanding. This area of research, which has been called architectural geometry, meanwhile contains a great wealth of individual contributions which are relevant in various fields. For mathematicians, the relation to discrete differential geometry is significant, in particular the integrable system viewpoint. Besides, new application contexts have become available for quite some old-established concepts. Regarding graphics and geometry processing, architectural geometry yields interesting new questions but also new objects, e.g. replacing meshes by other combinatorial arrangements. Numerical optimization plays a major role but in itself would be powerless without geometric understanding. Summing up, architectural geometry has become a rewarding field of study. We here survey the main directions which have been pursued, we show real projects where geometric considerations have played a role, and we outline open problems which we think are significant for the future development of both theory and practice of architectural geometry.

  19. Relational Architecture

    DEFF Research Database (Denmark)

    Reeh, Henrik

    2018-01-01

    in a scholarly institution (element #3), as well as the certified PhD scholar (element #4) and the architectural profession, notably its labour market (element #5). This first layer outlines the contemporary context which allows architectural research to take place in a dynamic relationship to doctoral education...... a human and institutional development going on since around 1990 when the present PhD institution was first implemented in Denmark. To be sure, the model is centred around the PhD dissertation (element #1). But it involves four more components: the PhD candidate (element #2), his or her supervisor...... and interrelated fields in which history, place, and sound come to emphasize architecture’s relational qualities rather than the apparent three-dimensional solidity of constructed space. A third layer of relational architecture is at stake in the professional experiences after the defence of the authors...

  20. Architectural Anthropology

    DEFF Research Database (Denmark)

    Stender, Marie

    Architecture and anthropology have always had a common focus on dwelling, housing, urban life and spatial organisation. Current developments in both disciplines make it even more relevant to explore their boundaries and overlaps. Architects are inspired by anthropological insights and methods......, while recent material and spatial turns in anthropology have also brought an increasing interest in design, architecture and the built environment. Understanding the relationship between the social and the physical is at the heart of both disciplines, and they can obviously benefit from further...... collaboration: How can qualitative anthropological approaches contribute to contemporary architecture? And just as importantly: What can anthropologists learn from architects’ understanding of spatial and material surroundings? Recent theoretical developments in anthropology stress the role of materials...

  1. Architectural Engineers

    DEFF Research Database (Denmark)

    Petersen, Rikke Premer

    engineering is addresses from two perspectives – as an educational response and an occupational constellation. Architecture and engineering are two of the traditional design professions and they frequently meet in the occupational setting, but at educational institutions they remain largely estranged....... The paper builds on a multi-sited study of an architectural engineering program at the Technical University of Denmark and an architectural engineering team within an international engineering consultancy based on Denmark. They are both responding to new tendencies within the building industry where...... the role of engineers and architects increasingly overlap during the design process, but their approaches reflect different perceptions of the consequences. The paper discusses some of the challenges that design education, not only within engineering, is facing today: young designers must be equipped...

  2. The Electric and Optical Properties of Doped Small Molecular Organic Light-Emitting Devices

    International Nuclear Information System (INIS)

    Kwang-Ohk Cheon

    2003-01-01

    Organic light-emitting devices (OLEDs) constitute a new and exciting emissive display technology. In general, the basic OLED structure consists of a stack of fluorescent organic layers sandwiched between a transparent conducting-anode and metallic cathode. When an appropriate bias is applied to the device, holes are injected from the anode and electrons from the cathode; some of the recombination events between the holes and electrons result in electroluminescence (EL). Until now, most of the efforts in developing OLEDs have focused on display applications, hence on devices within the visible range. However some organic devices have been developed for ultraviolet or infrared emission. Various aspects of the device physics of doped small molecular OLEDs were described and discussed. The doping layer thickness and concentration were varied systematically to study their effects on device performances, energy transfer, and turn-off dynamics. Low-energy-gap DCM2 guest molecules, in either α-NPD or DPVBi host layers, are optically efficient fluorophores but also generate deep carrier trap-sites. Since their traps reduce the carrier mobility, the current density decreases with increased doping concentration. At the same time, due to efficient energy transfer, the quantum efficiency of the devices is improved by light doping or thin doping thickness, in comparison with the undoped neat devices. However, heavy doping induces concentration quenching effects. Thus, the doping concentration and doping thickness may be optimized for best performance

  3. Co-deposition methods for the fabrication of organic optoelectronic devices

    Science.gov (United States)

    Thompson, Mark E.; Liu, Zhiwei; Wu, Chao

    2016-09-06

    A method for fabricating an OLED by preparing phosphorescent metal complexes in situ is provided. In particular, the method simultaneously synthesizes and deposits copper (I) complexes in an organic light emitting device. Devices comprising such complexes may provide improved photoluminescent and electroluminescent properties.

  4. The Electric and Optical Properties of Doped Small Molecular Organic Light-Emitting Devices

    Energy Technology Data Exchange (ETDEWEB)

    Cheon, Kwang-Ohk [Iowa State Univ., Ames, IA (United States)

    2003-01-01

    Organic light-emitting devices (OLEDs) constitute a new and exciting emissive display technology. In general, the basic OLED structure consists of a stack of fluorescent organic layers sandwiched between a transparent conducting-anode and metallic cathode. When an appropriate bias is applied to the device, holes are injected from the anode and electrons from the cathode; some of the recombination events between the holes and electrons result in electroluminescence (EL). Until now, most of the efforts in developing OLEDs have focused on display applications, hence on devices within the visible range. However some organic devices have been developed for ultraviolet or infrared emission. Various aspects of the device physics of doped small molecular OLEDs were described and discussed. The doping layer thickness and concentration were varied systematically to study their effects on device performances, energy transfer, and turn-off dynamics. Low-energy-gap DCM2 guest molecules, in either α-NPD or DPVBi host layers, are optically efficient fluorophores but also generate deep carrier trap-sites. Since their traps reduce the carrier mobility, the current density decreases with increased doping concentration. At the same time, due to efficient energy transfer, the quantum efficiency of the devices is improved by light doping or thin doping thickness, in comparison with the undoped neat devices. However, heavy doping induces concentration quenching effects. Thus, the doping concentration and doping thickness may be optimized for best performance.

  5. Reframing Architecture

    DEFF Research Database (Denmark)

    Riis, Søren

    2013-01-01

    I would like to thank Prof. Stephen Read (2011) and Prof. Andrew Benjamin (2011) for both giving inspiring and elaborate comments on my article “Dwelling in-between walls: the architectural surround”. As I will try to demonstrate below, their two different responses not only supplement my article...... focuses on how the absence of an initial distinction might threaten the endeavour of my paper. In my reply to Read and Benjamin, I will discuss their suggestions and arguments, while at the same time hopefully clarifying the postphenomenological approach to architecture....

  6. Surface tailoring of newly developed amorphous Znsbnd Sisbnd O thin films as electron injection/transport layer by plasma treatment: Application to inverted OLEDs and hybrid solar cells

    Science.gov (United States)

    Yang, Hongsheng; Kim, Junghwan; Yamamoto, Koji; Xing, Xing; Hosono, Hideo

    2018-03-01

    We report a unique amorphous oxide semiconductor Znsbnd Sisbnd O (a-ZSO) which has a small work function of 3.4 eV for as-deposited films. The surface modification of a-ZSO thin films by plasma treatments is examined to apply it to the electron injection/transport layer of organic devices. It turns out that the energy alignment and exciton dissociation efficiency at a-ZSO/organic semiconductor interface significantly changes by choosing different gas (oxygen or argon) for plasma treatments (after a-ZSO was exposed to atmospheric environment for 5 days). In situ ultraviolet photoelectron spectroscopy (UPS) measurement reveals that the work function of a-ZSO is increased to 4.0 eV after an O2-plasma treatment, while the work function of 3.5 eV is recovered after an Ar-plasma treatment which indicates this treatment is effective for surface cleaning. To study the effects of surface treatments to device performance, OLEDs and hybrid polymer solar cells with O2-plasma or Ar-plasma treated a-ZSO are compared. Effects of these surface treatments on performance of inverted OLEDs and hybrid polymer solar cells are examined. Ar-plasma treated a-ZSO works well as the electron injection layer in inverted OLEDs (Alq3/a-ZSO) because the injection barrier is small (∼ 0.1 eV). On the other hands, O2-plasma treated a-ZSO is more suitable for application to hybrid solar cells which is benefiting from higher exciton dissociation efficiency at polymer (P3HT)/ZSO interface.

  7. New concept for in-line OLED manufacturing

    Science.gov (United States)

    Hoffmann, U.; Landgraf, H.; Campo, M.; Keller, S.; Koening, M.

    2011-03-01

    A new concept of a vertical In-Line deposition machine for large area white OLED production has been developed. The concept targets manufacturing on large substrates (>= Gen 4, 750 x 920 mm2) using linear deposition source achieving a total material utilization of >= 50 % and tact time down to 80 seconds. The continuously improved linear evaporation sources for the organic material achieve thickness uniformity on Gen 4 substrate of better than +/- 3 % and stable deposition rates down to less than 0.1 nm m/min and up to more than 100 nm m/min. For Lithium-Fluoride but also for other high evaporation temperature materials like Magnesium or Silver a linear source with uniformity better than +/- 3 % has been developed. For Aluminum we integrated a vertical oriented point source using wire feed to achieve high (> 150 nm m/min) and stable deposition rates. The machine concept includes a new vertical vacuum handling and alignment system for Gen 4 shadow masks. A complete alignment cycle for the mask can be done in less than one minute achieving alignment accuracy in the range of several 10 μm.

  8. White OLED in Hybrid Structure for Enhancing Color Purity.

    Science.gov (United States)

    Kim, Dong-Eun; Kang, Min-Jae; Park, Gwang-Ryeol; Lee, Burm-Jong; Kwon, Young-Soo; Shin, Hoon-Kyu

    2016-06-01

    We synthesized the red emission material, bis(1,4-bis(5-phenyloxazol-2-yl)phenyl) iridium(picolate) [Ir-complexes] and the blue emission material, bis (2-(2-hydroxyphenyl) benzoxazolate)zinc [Zn(HPB)2]. White Organic Light Emitting Diodes were fabricated by using Zn(HPB)2 for a blue emitting layer, Ir-complexes for a red emitting layer and a tris (8-hydroxy quinoline)aluminum [Alq3] for a green emitting layer. The important experimental results obtained, white OLED was fabricated by using double emitting layers of Zn(HPB)2 and Alq3:Ir-complexes, and hole blocking layer of 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline[BCP]. We also varied the thickness of BCP. When the thickness of BCP layer was 5 nm, white emission was achieved. We obtained a maximum luminance of 5400 cd/m2 at a current density of 650 mA/cm2. The CIE coordinates was (0.339, 0.323) at voltage of 10 V.

  9. A synaptic device built in one diode-one resistor (1D-1R) architecture with intrinsic SiOx-based resistive switching memory

    Science.gov (United States)

    Chang, Yao-Feng; Fowler, Burt; Chen, Ying-Chen; Zhou, Fei; Pan, Chih-Hung; Chang, Kuan-Chang; Tsai, Tsung-Ming; Chang, Ting-Chang; Sze, Simon M.; Lee, Jack C.

    2016-04-01

    We realize a device with biological synaptic behaviors by integrating silicon oxide (SiOx) resistive switching memory with Si diodes to further minimize total synaptic power consumption due to sneak-path currents and demonstrate the capability for spike-induced synaptic behaviors, representing critical milestones for the use of SiO2-based materials in future neuromorphic computing applications. Biological synaptic behaviors such as long-term potentiation, long-term depression, and spike-timing dependent plasticity are demonstrated systemically with comprehensive investigation of spike waveform analyses and represent a potential application for SiOx-based resistive switching materials. The resistive switching SET transition is modeled as hydrogen (proton) release from the (SiH)2 defect to generate the hydrogenbridge defect, and the RESET transition is modeled as an electrochemical reaction (proton capture) that re-forms (SiH)2. The experimental results suggest a simple, robust approach to realize programmable neuromorphic chips compatible with largescale complementary metal-oxide semiconductor manufacturing technology.

  10. Textile Architecture

    DEFF Research Database (Denmark)

    Heimdal, Elisabeth Jacobsen

    2010-01-01

    Textiles can be used as building skins, adding new aesthetic and functional qualities to architecture. Just like we as humans can put on a coat, buildings can also get dressed. Depending on our mood, or on the weather, we can change coat, and so can the building. But the idea of using textiles...

  11. AC-driven organic light emission devices with carbon nanotubes

    Science.gov (United States)

    Jeon, So-Yeon; Yu, SeGi

    2017-02-01

    We have investigated alternating current (AC)-driven organic light-emitting devices (OLEDs), with carbon nanotubes (CNTs) incorporated within the emission layer. With CNT incorporation, the brightness of the OLEDs was substantially improved, and the turn-on voltage was reduced by at least a factor of five. Furthermore, the current levels of the CNT-incorporated OLEDs were lower than that of the reference device. A roughly 70% decrease in the current level was obtained for a CNT concentration of 0.03 wt%. This was accomplished by keeping the concentration of CNTs low and the length of CNTs short, which helped to suppress the percolation networking of CNTs within the emitting layer. Strong local electric fields near the end-tips of CNTs and micro-capacitors formed by dispersed CNTs might have caused this high brightness and these low currents. CNT incorporation in the emitting layer can improve the characteristics of AC-driven OLEDs, which are considered to be one of the candidates for flat panel displays and lightning devices.

  12. AC-driven Organic Light Emission Devices with Carbon Nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Jeon, So-Yeon [Sungkyunkwan University, Suwon (Korea, Republic of); Yu, SeGi [Hankuk University of Foreign Studies, Yongin (Korea, Republic of)

    2017-02-15

    We have investigated alternating current (AC)-driven organic light-emitting devices (OLEDs), with carbon nanotubes (CNTs) incorporated within the emission layer. With CNT incorporation, the brightness of the OLEDs was substantially improved, and the turn-on voltage was reduced by at least a factor of five. Furthermore, the current levels of the CNT-incorporated OLEDs were lower than that of the reference device. A roughly 70% decrease in the current level was obtained for a CNT concentration of 0.03 wt%. This was accomplished by keeping the concentration of CNTs low and the length of CNTs short, which helped to suppress the percolation networking of CNTs within the emitting layer. Strong local electric fields near the end-tips of CNTs and micro-capacitors formed by dispersed CNTs might have caused this high brightness and these low currents. CNT incorporation in the emitting layer can improve the characteristics of AC-driven OLEDs, which are considered to be one of the candidates for flat panel displays and lightning devices.

  13. High efficient OLED displays prepared with the air-gapped bridges on quantum dot patterns for optical recycling

    OpenAIRE

    Hyo-Jun Kim; Min-Ho Shin; Joo-Suc Kim; Se-Eun Kim; Young-Joo Kim

    2017-01-01

    An optically efficient structure was proposed and fabricated to realize high brightness organic light emitting diode (OLED) displays based on a white OLED prepared with the air-gapped bridges on the quantum dot (QD) patterns. Compared with a conventional white OLED display, in our experiments, the optical intensity of the proposed OLED display shows the enhancement of 58.2% in the red color and 16.8% in the green color after applying the air-gapped bridge structure on QD patterns of 20?wt% co...

  14. From green architecture to architectural green

    DEFF Research Database (Denmark)

    Earon, Ofri

    2011-01-01

    that describes the architectural exclusivity of this particular architecture genre. The adjective green expresses architectural qualities differentiating green architecture from none-green architecture. Currently, adding trees and vegetation to the building’s facade is the main architectural characteristics...... they have overshadowed the architectural potential of green architecture. The paper questions how a green space should perform, look like and function. Two examples are chosen to demonstrate thorough integrations between green and space. The examples are public buildings categorized as pavilions. One......The paper investigates the topic of green architecture from an architectural point of view and not an energy point of view. The purpose of the paper is to establish a debate about the architectural language and spatial characteristics of green architecture. In this light, green becomes an adjective...

  15. Urban Sustainability through Public Architecture

    Directory of Open Access Journals (Sweden)

    Soomi Kim

    2018-04-01

    Full Text Available As the sustainability of contemporary cities has gained emphasis, interest in architecture has increased, due to its social and public responsibility. Since sustainability is linked to public values, research on sustainable public spaces is an important way to secure sustainability in cities. Based on this, we analyzed the sustainability of European cities by examining the design methods of public architecture according to the region. The aim of the study is to derive architectural methodology corresponding to local characteristics, and to suggest issues to consider in public architecture design to promote urban sustainability based on this. First, regarding the environmental aspect, it can be observed that there is an effort to secure sustainability. Second, in terms of social sustainability, historical value remains as a trace of architectural place, so that it continues in people’s memory. In addition, public architecture provides public places where citizens can gather and enjoy programs, while the architectural methods showed differences influenced by cultural conditions. Third, in economic sustainability, it was shown that energy saving was achieved through cost reduction through recycling of materials, facilities, or environmental factors. In conclusion, the issues to be considered in public architectural design are the voiding of urban space through architectural devices in the construction method. In other words, the intention is to form “ground” that attempts to be part of the city, and thereby create better places. Since skin and material have a deep relationship with the environment, they should have the durability and an outer skin that are suitable for the regional environment. Finally, sustainability is to be utilized through the influx of programs that meet local and environmental characteristics. Design research into public architecture that is oriented towards urban sustainability will be a task to be carried out by the

  16. Study of shifting of recombination zone in multi-emissive layer organic light emitting devices and its effect on color stability

    International Nuclear Information System (INIS)

    Tyagi, Priyanka; Srivastava, Ritu; Kumar, Arunandan; Tuli, Suneet; Kamalasanan, M.N.

    2013-01-01

    Color stability in multi-emissive layer organic light emitting devices (Me-OLEDs) has been investigated. Me-OLEDs were based on multiple emitters with a common host CBP doped with three dopants, BCzVBi, Ir(ppy) 3 and Ir(btp) 2 acac for blue, green and red emission. A major variation in CIE coordinates were found from (0.312, 0.294) to (0.236, 0.267) with increase in voltage from 6 to 9 V. This coordinate shift in Me-OLEDs has been attributed to the shifting of recombination zone with increase in voltage. In order to support our experimental observation, the EL spectrum of Me-OLEDs has been expressed as a linear combination of EL intensities of OLEDs with its individual constituting layers as emitters. In this way, the contribution of each layer in the EL spectrum of Me-OLEDs has been evaluated at each voltage. It has been observed from these calculations that the contribution of red emitter decreases from 47% to 33.33% and blue emitter increases from 38% to 51.67% with the increase in voltage from 6 to 9 V. This supports our hypothesis of shifting of recombination zone with the change in voltage. This shifting has been attributed to the field dependency of electron mobility in CBP. Me-OLED with CBP layers between the emitters was fabricated to improve the color stability. Significant improvement in color stability was achieved without changes in current efficiency in Me-OLED with interlayers. Highlights: ► Me-OLEDs have been fabricated by using three primary colors (RGB). ► CIE coordinates of these Me-OLEDs were voltage dependent. ► Analytical fitting has been performed to study the shifting of recombination zone. ► CBP interlayers have been introduced to improve the color stability. ► Color stability has been improved without any change in current efficiency

  17. Layered Architecture for Quantum Computing

    Directory of Open Access Journals (Sweden)

    N. Cody Jones

    2012-07-01

    Full Text Available We develop a layered quantum-computer architecture, which is a systematic framework for tackling the individual challenges of developing a quantum computer while constructing a cohesive device design. We discuss many of the prominent techniques for implementing circuit-model quantum computing and introduce several new methods, with an emphasis on employing surface-code quantum error correction. In doing so, we propose a new quantum-computer architecture based on optical control of quantum dots. The time scales of physical-hardware operations and logical, error-corrected quantum gates differ by several orders of magnitude. By dividing functionality into layers, we can design and analyze subsystems independently, demonstrating the value of our layered architectural approach. Using this concrete hardware platform, we provide resource analysis for executing fault-tolerant quantum algorithms for integer factoring and quantum simulation, finding that the quantum-dot architecture we study could solve such problems on the time scale of days.

  18. MUF architecture /art London

    DEFF Research Database (Denmark)

    Svenningsen Kajita, Heidi

    2009-01-01

    Om MUF architecture samt interview med Liza Fior og Katherine Clarke, partnere i muf architecture/art......Om MUF architecture samt interview med Liza Fior og Katherine Clarke, partnere i muf architecture/art...

  19. Influence of ITO patterning on reliability of organic light emitting devices

    International Nuclear Information System (INIS)

    Wang, Zhaokui; Naka, Shigeki; Okada, Hiroyuki

    2009-01-01

    Indium tin oxide (ITO) films are widely used for a transparent electrode of organic light emitting devices (OLEDs) because of its excellent conductivity and transparency. Two types of ITO substrates with different surface roughness were selected to use as anode of OLEDs. In addition, two types of etching process of ITO substrate, particularly the etching time, were also carried out. It was found that the surface roughness and/or the etching process of ITO substrate strongly influenced on an edge of ITO surface, further affected the operating characteristics and reliability of devices.

  20. FDTD analysis of the light extraction efficiency of OLEDs with a random scattering layer.

    Science.gov (United States)

    Kim, Jun-Whee; Jang, Ji-Hyang; Oh, Min-Cheol; Shin, Jin-Wook; Cho, Doo-Hee; Moon, Jae-Hyun; Lee, Jeong-Ik

    2014-01-13

    The light extraction efficiency of OLEDs with a nano-sized random scattering layer (RSL-OLEDs) was analyzed using the Finite Difference Time Domain (FDTD) method. In contrast to periodic diffraction patterns, the presence of an RSL suppresses the spectral shift with respect to the viewing angle. For FDTD simulation of RSL-OLEDs, a planar light source with a certain spatial and temporal coherence was incorporated, and the light extraction efficiency with respect to the fill factor of the RSL and the absorption coefficient of the material was investigated. The design results were compared to the experimental results of the RSL-OLEDs in order to confirm the usefulness of FDTD in predicting experimental results. According to our FDTD simulations, the light confined within the ITO-organic waveguide was quickly absorbed, and the absorption coefficients of ITO and RSL materials should be reduced in order to obtain significant improvement in the external quantum efficiency (EQE). When the extinction coefficient of ITO was 0.01, the EQE in the RSL-OLED was simulated to be enhanced by a factor of 1.8.

  1. A spectral measurement method for determining white OLED average junction temperatures

    Science.gov (United States)

    Zhu, Yiting; Narendran, Nadarajah

    2016-09-01

    The objective of this study was to investigate an indirect method of measuring the average junction temperature of a white organic light-emitting diode (OLED) based on temperature sensitivity differences in the radiant power emitted by individual emitter materials (i.e., "blue," "green," and "red"). The measured spectral power distributions (SPDs) of the white OLED as a function of temperature showed amplitude decrease as a function of temperature in the different spectral bands, red, green, and blue. Analyzed data showed a good linear correlation between the integrated radiance for each spectral band and the OLED panel temperature, measured at a reference point on the back surface of the panel. The integrated radiance ratio of the spectral band green compared to red, (G/R), correlates linearly with panel temperature. Assuming that the panel reference point temperature is proportional to the average junction temperature of the OLED panel, the G/R ratio can be used for estimating the average junction temperature of an OLED panel.

  2. Architectural fragments

    DEFF Research Database (Denmark)

    Bang, Jacob Sebastian

    2018-01-01

    I have created a large collection of plaster models: a collection of Obstructions, errors and opportunities that may develop into architecture. The models are fragments of different complex shapes as well as more simple circular models with different profiling and diameters. In this contect I have....... I try to invent the ways of drawing the models - that decode and unfold them into architectural fragments- into future buildings or constructions in the landscape. [1] Luigi Moretti: Italian architect, 1907 - 1973 [2] Man Ray: American artist, 1890 - 1976. in 2015, I saw the wonderful exhibition...... "Man Ray - Human Equations" at the Glyptotek in Copenhagen, organized by the Philips Collection in Washington D.C. and the Israel Museum in Jerusalem (in 2013). See also: "Man Ray - Human Equations" catalogue published by Hatje Cantz Verlag, Germany, 2014....

  3. Kosmos = architecture

    Directory of Open Access Journals (Sweden)

    Tine Kurent

    1985-12-01

    Full Text Available The old Greek word "kosmos" means not only "cosmos", but also "the beautiful order", "the way of building", "building", "scenography", "mankind", and, in the time of the New Testament, also "pagans". The word "arhitekton", meaning first the "master of theatrical scenography", acquired the meaning of "builder", when the words "kosmos" and ~kosmetes" became pejorative. The fear that architecture was not considered one of the arts before Renaissance, since none of the Muses supervised the art of building, results from the misunderstanding of the word "kosmos". Urania was the Goddes of the activity implied in the verb "kosmein", meaning "to put in the beautiful order" - everything, from the universe to the man-made space, i. e. the architecture.

  4. Metabolistic Architecture

    DEFF Research Database (Denmark)

    2013-01-01

    Textile Spaces presents different approaches to using textile as a spatial definer and artistic medium. The publication collages images and text, art and architecture, science, philosophy and literature, process and product, past, present and future. It forms an insight into soft materials' funct......' functional and poetic potentials, linking the disciplines through fragments that aim to inspire a further look into the artists' and architects' practices, while simultaneously framing these textile visions in a wider context.......Textile Spaces presents different approaches to using textile as a spatial definer and artistic medium. The publication collages images and text, art and architecture, science, philosophy and literature, process and product, past, present and future. It forms an insight into soft materials...

  5. Italian bioclimatic architecture

    Energy Technology Data Exchange (ETDEWEB)

    D' Errico, E

    1987-04-01

    This paper deals with the results of solar space heating research developed within the Finalized Energy Project of the National Research Council of Italy. Energy and cost/benefit parameters were compared for a certain number of Italian buildings incorporating solar architecture. The technical and economic analysis was performed on 31 buildings, of which 24 are residential, and 7 are schools, with different solar devices (direct gain, Trombe walls, sunspaces, hybrid systems). The buildings were constructed between 1976 and 1982. The results emphasize that simple technologies with lower costs and good design usually have a higher performance/cost ratio.

  6. One step process of decomposition and polymerization to fabricate SiO{sub 2} hollow spheres/polyimide composite for foldable OLEDs

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Min Kyu [SKKU Advanced Institute of Nanotechnology (SAINT) and Center for Human Interface Nano Technology (HINT), Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Kim, Dong Won; Moon, Soo Hyun [School of Advanced Materials Science & Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Shin, Dong-Wook [SKKU Advanced Institute of Nanotechnology (SAINT) and Center for Human Interface Nano Technology (HINT), Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); College of Engineering, Mathematics and Physical Sciences, University of Exeter, Stocker Road, Exeter EX4 4QL (United Kingdom); Oh, Tae Sik [School of Mechanical and ICT Convergence Engineering, Sunmoon University, Asan 336-708 (Korea, Republic of); Yoo, Ji Beom, E-mail: jbyoo@skku.edu [SKKU Advanced Institute of Nanotechnology (SAINT) and Center for Human Interface Nano Technology (HINT), Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); School of Advanced Materials Science & Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of)

    2017-03-15

    Graphical abstract: The SiO{sub 2} hollow spheres and polyimide hybrid synthesized using one step process, simultaneous occurrence of decomposition and polymerization (SODP) is useful with a ultra-low dielectric constant and high thermal stability for flexible OLED. - Highlights: • We fabricated hybrid films of SHS/PI by using a one step process with SODP. • The film has ultralow dielectric constant (50 vol% at k = 1.67). • There is no collapse of SiO{sub 2} hollow spheres in the PI matrix after bending test for 50,000 cycles. - Abstract: The fabrication of interlayer dielectrics (ILDs) in flexible organic light-emitting diodes (OLEDs) requires flexible materials with a low dielectric constant as well as materials with excellent electrical, thermal, and mechanical properties for optimal device performance. Hybrid films of SiO{sub 2} hollow spheres (SHS)/polyimide (PI) were prepared using a one-step process, with simultaneous occurrence of decomposition (polystyrene, PS) and polymerization (PI) (SODP). No collapse of SiO{sub 2} hollow spheres in PI was observed from 10 vol% to 60 vol% SHS in hybrid films. The dielectric constant of hybrid films was reduced from 3.45 to 1.67 and was saturated at above 50 vol% of SHS due to the maximum fill factor of SHS in the PI matrix. The thermal stability was excellent up to 500 °C due to the inherent thermal property of PI. After a bending test for 50,000 cycles at a bending radius of 1 mm, the SHS/PI hybrid films retained their dielectric constant and current density. These results indicate the hybrid film to be the most promising candidate for flexible ILDs with a low dielectric constant and high thermal stability for foldable OLEDs.

  7. One step process of decomposition and polymerization to fabricate SiO_2 hollow spheres/polyimide composite for foldable OLEDs

    International Nuclear Information System (INIS)

    Kim, Min Kyu; Kim, Dong Won; Moon, Soo Hyun; Shin, Dong-Wook; Oh, Tae Sik; Yoo, Ji Beom

    2017-01-01

    Graphical abstract: The SiO_2 hollow spheres and polyimide hybrid synthesized using one step process, simultaneous occurrence of decomposition and polymerization (SODP) is useful with a ultra-low dielectric constant and high thermal stability for flexible OLED. - Highlights: • We fabricated hybrid films of SHS/PI by using a one step process with SODP. • The film has ultralow dielectric constant (50 vol% at k = 1.67). • There is no collapse of SiO_2 hollow spheres in the PI matrix after bending test for 50,000 cycles. - Abstract: The fabrication of interlayer dielectrics (ILDs) in flexible organic light-emitting diodes (OLEDs) requires flexible materials with a low dielectric constant as well as materials with excellent electrical, thermal, and mechanical properties for optimal device performance. Hybrid films of SiO_2 hollow spheres (SHS)/polyimide (PI) were prepared using a one-step process, with simultaneous occurrence of decomposition (polystyrene, PS) and polymerization (PI) (SODP). No collapse of SiO_2 hollow spheres in PI was observed from 10 vol% to 60 vol% SHS in hybrid films. The dielectric constant of hybrid films was reduced from 3.45 to 1.67 and was saturated at above 50 vol% of SHS due to the maximum fill factor of SHS in the PI matrix. The thermal stability was excellent up to 500 °C due to the inherent thermal property of PI. After a bending test for 50,000 cycles at a bending radius of 1 mm, the SHS/PI hybrid films retained their dielectric constant and current density. These results indicate the hybrid film to be the most promising candidate for flexible ILDs with a low dielectric constant and high thermal stability for foldable OLEDs.

  8. "Kus sa oled mu võluratsu..." : [luuletused] / Mõkola Vingranovski ; tlk. Harald Rajamets

    Index Scriptorium Estoniae

    Vingranovski, Mõkola

    2004-01-01

    Sisu: "Kus sa oled mu võluratsu..." ; Ja rahvas on... ; "Oled rada, mu armsam..." ; "Sa oled siin! Mu armastus, mu lumm..." ; "Me ahvatluste aastad, albid aastad..." ; "Mul juba siis, kui oli kevad veel..." ; "Nüüd tõuse, kalur! Kustumas on tähed..." ; Meresügisel ; "Kauss hirsiputru, õilmelend..." ; "Õde võõpab aias õunapuid..." ; Esimene hälilaul ; "Noor tüdruk, alles laps. Ei kõnni kikivarvul..." ; "Ülal künka peal seisis päike..." ; "Jäid suve lõpul tuhmiks puud..." ; "Nüüd hakkab lumesadu, nüüd..." ; "Lumehämarus, hall nagu hall..." ; "Tüüpõllu aur on jäärakute kohal..." ; "Parv linde kriiskab salu kohal..." ; "Põld kuivi maisivarsi täis..." ; Haiavata

  9. IoT gateway architecture

    OpenAIRE

    Leleika, Paulius

    2017-01-01

    This paper provides an overview of HTTP, CoAP, AMQP, DDS, MQTT, XMPP communication protocols. The main IoT problem is that IoT devices uses many different communication protocols and devices cannot communicate with each other directly. IoT gateway helps to solve that problem. This paper also identifies requirements for IoT gateway software. Provides solution for communication between devices which are using different messaging architectures. Presents security aspects and ways to secure IoT ga...

  10. GATEWAY Report Brief: Evaluating OLED Lighting in the Accounting Office of DeJoy, Knauf & Blood LLP

    Energy Technology Data Exchange (ETDEWEB)

    None

    2017-08-21

    Summary of GATEWAY report evaluating a new lighting system, at the offices of the accounting firm of DeJoy, Knauf & Blood, LLP in Rochester, NY, that incorporates a number of different OLED luminaires. Evaluation of the OLED products included efficacy performance, field measurements of panel color, flicker measurements, and staff feedback.

  11. Ultra-thin fluoropolymer buffer layer as an anode stabilizer of organic light emitting devices

    International Nuclear Information System (INIS)

    Yang, Nam Chul; Lee, Jaeho; Song, Myung-Won; Ahn, Nari; Kim, Mu-Hyun; Lee, Songtaek; Chin, Byung Doo

    2007-01-01

    We have investigated the effect of thin fluoro-acrylic polymer as an anode stabilizer on the lifetime of an organic light emitting device (OLED). Surface chemical properties of commercial fluoropolymer, FC-722 (Fluorad(TM) of 3M), on indium-tin oxide (ITO) were characterized by x-ray photoemission spectroscopy. An OLED with 1 nm thick fluoropolymeric film showed identical brightness and efficiency behaviour and improved operational stability compared with the reference device with UV-O 3 treated ITO. The improvement in the lifetime was accompanied by the suppression of the voltage increase at the initial stage of constant-current driving, which can be attributed to the action of the FC-722 layer by smoothing the ITO surface. Fluoropolymer coating, therefore, improves the lifetime of the small molecular OLED by the simple and reliable anode-stabilizing process

  12. Spectroscopic mapping and selective electronic tuning of molecular orbitals in phosphorescent organometallic complexes – a new strategy for OLED materials

    Directory of Open Access Journals (Sweden)

    Pascal R. Ewen

    2014-11-01

    Full Text Available The improvement of molecular electronic devices such as organic light-emitting diodes requires fundamental knowledge about the structural and electronic properties of the employed molecules as well as their interactions with neighboring molecules or interfaces. We show that highly resolved scanning tunneling microscopy (STM and spectroscopy (STS are powerful tools to correlate the electronic properties of phosphorescent complexes (i.e., triplet emitters with their molecular structure as well as the local environment around a single molecule. We used spectroscopic mapping to visualize several occupied and unoccupied molecular frontier orbitals of Pt(II complexes adsorbed on Au(111. The analysis showed that the molecules exhibit a peculiar localized strong hybridization that leads to partial depopulation of a dz² orbital, while the ligand orbitals are almost unchanged. We further found that substitution of functional groups at well-defined positions can alter specific molecular orbitals without influencing the others. The results open a path toward the tailored design of electronic and optical properties of triplet emitters by smart ligand substitution, which may improve the performance of future OLED devices.

  13. Voltage color tunable OLED with (Sm,Eu)-β-diketonate complex blend

    Science.gov (United States)

    Reyes, R.; Cremona, M.; Teotonio, E. E. S.; Brito, H. F.; Malta, O. L.

    2004-09-01

    Light emission from organic electroluminescent diodes (OLEDs) in which mixed samarium and europium β-diketonate complexes, [Sm 0.7Eu 0.3(TTA) 3(TPPO) 2], was used as the emitting layer is described. The electroluminescence spectra exhibit narrow peaks arising from 4f-intraconfigurational transitions of the Sm 3+ and Eu 3+ ions and a broad emission band attributed to the electrophosphorescence of the TTA ligand. The intensity ratio of the peaks determined by the bias voltage applied to the OLED, together with the ligand electrophosphorescence, allows to obtain a voltage-tunable color light source.

  14. High-performance blue phosphorescent OLEDs using energy transfer from exciplex.

    Science.gov (United States)

    Seino, Yuki; Sasabe, Hisahiro; Pu, Yong-Jin; Kido, Junji

    2014-03-12

    An efficient energy transfer from an exciplex between a sulfone and an arylamine derivatives to a blue phosphorescent emitter enables OLED performances among the best, of over 50 lm W(-1) at 100 cd m(-2) . The formation of the exciplex realizes a barrier-free hole-electron recombination pathway, thereby leading to high OLED performances with an extremely low driving voltage of 2.9 V at 100 cd m(-2) . © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. La generación de ingresos comerciales en los aeropuertos españoles

    OpenAIRE

    Roberto Rendeiro Martín-Cejas; Francisco López del Pino

    2004-01-01

    Este trabajo pretende analizar la importancia del tráfico internacional y el nivel de servicio establecido en la generación de ingresos comerciales en los aeropuertos españoles. En primer lugar, mediante un modelo ad hoc de ingresos, se valora la influencia de las diferentes clases de tráfico en la generación de ingresos de la red de aeropuertos españoles. Se estima, asimismo, la importancia de disponer de tiendas libres de impuestos en la capacidad de generar ingresos comerciales. Seguidamen...

  16. España y los españoles

    Directory of Open Access Journals (Sweden)

    Caba, Rubén

    2011-10-01

    Full Text Available The author here argues in favour of the historical reality that we call Spain. To recognize the Cadiz Constitution of 1812 as the origin of present Spain, he maintains, does not imply that our country had no national identity before the 19th century. And to this effect he expounds the famous controversy between Americo Castro and Claudio Sánchez-Albornoz. Before the Arab invasion there were no “españoles”, since this word of provençal origin dates back to the 11th century, as Castro points out. However, it is also true that during the Roman as well the Gothic domination, the peninsular inhabitants were known as “hispani”, as Sánchez-Albornoz sarcastically alleges. In addition, this article includes a number of quotations from Latin, Gothic and Spanish writers of the Middle Ages and the Renaissance, references which bear witness to a feeling of belonging to an old country called “Hispania” or “España”.

    El autor aporta argumentos en favor de la realidad histórica que llamamos España. Sostiene que reconocer a la Constitución de Cádiz de 1812 como origen de la España política actual no implica que nuestro país careciera de identidad nacional antes del siglo XIX. Y expone la controversia de Américo Castro y de Claudio Sánchez-Albornoz sobre la génesis histórica de España para concluir que, si bien antes de la invasión árabe no había “españoles”, vocablo provenzal del siglo XI como advierte Castro, también es cierto que durante la dominación romana y goda los peninsulares eran “hispani”, como alega con sorna Sánchez-Albornoz. Además, se recogen citas de autores latinos, godos y españoles tanto medievales como renacentistas que testimonian su sentimiento de pertenecer a un viejo país llamado Hispania o España.

  17. Connecting Architecture and Implementation

    Science.gov (United States)

    Buchgeher, Georg; Weinreich, Rainer

    Software architectures are still typically defined and described independently from implementation. To avoid architectural erosion and drift, architectural representation needs to be continuously updated and synchronized with system implementation. Existing approaches for architecture representation like informal architecture documentation, UML diagrams, and Architecture Description Languages (ADLs) provide only limited support for connecting architecture descriptions and implementations. Architecture management tools like Lattix, SonarJ, and Sotoarc and UML-tools tackle this problem by extracting architecture information directly from code. This approach works for low-level architectural abstractions like classes and interfaces in object-oriented systems but fails to support architectural abstractions not found in programming languages. In this paper we present an approach for linking and continuously synchronizing a formalized architecture representation to an implementation. The approach is a synthesis of functionality provided by code-centric architecture management and UML tools and higher-level architecture analysis approaches like ADLs.

  18. Nickel doped indium tin oxide anode and effect on dark spot development of organic light-emitting devices

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, C.M. [Southern Taiwan University, Department of Electro-Optical Engineering, 1 Nan-Tai St, Yung-Kang City, Tainan County 710, Taiwan (China)], E-mail: tedhsu@mail.stut.edu.tw; Kuo, C.S.; Hsu, W.C.; Wu, W.T. [Southern Taiwan University, Department of Electro-Optical Engineering, 1 Nan-Tai St, Yung-Kang City, Tainan County 710, Taiwan (China)

    2009-01-01

    This article demonstrated that introducing nickel (Ni) atoms into an indium tin oxide (ITO) anode could considerably decrease ITO surface roughness and eliminate the formation of dark spots of an organic light-emitting device (OLED). A dramatic drop in surface roughness from 6.52 nm of an conventional ITO to 0.46 nm of an 50 nm Ni(50 W)-doped ITO anode was observed, and this led to an improved lifetime performance of an Alq3 based OLED device attributed to reduced dark spots. Reducing thickness of Ni-doped ITO anode was found to worsen surface roughness. Meanwhile, the existence of Ni atoms showed little effect on deteriorating the light-emitting mechanism of OLED devices.

  19. Efficient non-doped phosphorescent orange, blue and white organic light-emitting devices

    Science.gov (United States)

    Yin, Yongming; Yu, Jing; Cao, Hongtao; Zhang, Letian; Sun, Haizhu; Xie, Wenfa

    2014-10-01

    Efficient phosphorescent orange, blue and white organic light-emitting devices (OLEDs) with non-doped emissive layers were successfully fabricated. Conventional blue phosphorescent emitters bis [4,6-di-fluorophenyl]-pyridinato-N,C2'] picolinate (Firpic) and Bis(2,4-difluorophenylpyridinato) (Fir6) were adopted to fabricate non-doped blue OLEDs, which exhibited maximum current efficiency of 7.6 and 4.6 cd/A for Firpic and Fir6 based devices, respectively. Non-doped orange OLED was fabricated utilizing the newly reported phosphorescent material iridium (III) (pbi)2Ir(biq), of which manifested maximum current and power efficiency of 8.2 cd/A and 7.8 lm/W. The non-doped white OLEDs were achieved by simply combining Firpic or Fir6 with a 2-nm (pbi)2Ir(biq). The maximum current and power efficiency of the Firpic and (pbi)2Ir(biq) based white OLED were 14.8 cd/A and 17.9 lm/W.

  20. Method for applying a thin film barrier stack to a device with microstructures, and device provided with such a thin film barrier stack

    NARCIS (Netherlands)

    2005-01-01

    A method for applying a thin film barrier stack to a device with microstructures, such as, for instance, an OLED, wherein the thin film barrier stack forms a barrier to at least moisture and oxygen, wherein the stack is built up from a combination of org. and inorg. layers, characterized in that a

  1. High efficiency fluorescent white OLEDs based on DOPPP

    Science.gov (United States)

    Zhang, Gang; Chen, Chen; Lang, Jihui; Zhao, Lina; Jiang, Wenlong

    2017-08-01

    The white organic light-emitting devices (WOLED) with the structures of ITO/m-MTDATA (10 nm)/NPB (30 nm)/Rubrene (0.2 nm)/DOPPP (x nm)/TAz (10 nm)/Alq3 (30 nm)/LiF (0.5 nm)/Al and ITO/NPB (30 nm)/DPAVBi:Rubrene (2 wt.%, 20 nm)/ DOPPP (x nm)/TAZ (10 nm)/Alq3 (30 nm)/LiF (0.5 nm)/Al (100 nm) have been fabricated by the vacuum thermal evaporation method. The results show that the chroma of the non-doped device is the best and the color coordinates are in the range of white light. The maximum luminance is 12,750 cd/m2 and the maximum current efficiency is 8.55 cd/A. The doped device A has the maximum luminance (16,570 cd/m2), when the thickness of blue layer DOPPP is 25 nm, and the doped device B achieves the highest efficiency (10.47 cd/A), when the thickness of DOPPP is 15 nm. All the performances of the doped devices are better than the non-doped one. The results demonstrate that the doped structures can realize the energy transfer and then improve the performance of the device effectively.

  2. Realizing Highly Efficient Solution-Processed Homojunction-Like Sky-Blue OLEDs by Using Thermally Activated Delayed Fluorescent Emitters Featuring an Aggregation-Induced Emission Property.

    Science.gov (United States)

    Wu, Kailong; Wang, Zian; Zhan, Lisi; Zhong, Cheng; Gong, Shaolong; Xie, Guohua; Yang, Chuluo

    2018-04-05

    Two new blue emitters, i.e., bis-[2-(9,9-dimethyl-9,10-dihydroacridine)-phenyl]-sulfone ( o-ACSO2) and bis-[3-(9,9-dimethyl-9,10-dihydroacridine)-phenyl]-sulfone ( m-ACSO2), with reserved fine thermally activated delayed fluorescent (TADF) nature and simply tuned thermal and optoelectronic properties, were synthesized by isomer engineering. The meta-linking compound, i.e., m-ACSO2, obtains the highest photoluminescence quantum yield with a small singlet-triplet energy gap, a moderate delayed fluorescent lifetime, excellent solubility, and neat film homogeneity. Due to its unique aggregation-induced emission (AIE) character, neat film-based heterojunction-like organic light-emitting diodes (OLEDs) are achievable. By inserting an excitonic inert exciton-blocking layer, the PN heterojunction-like emission accompanied by intefacial exciplex was shifted to a homojunction-like channel mainly from the AIE emitter itself, providing a new tactic to generate efficient blue color from neat films. The solution-processed nondoped sky-blue OLED employing m-ACSO2 as emitter with homojunction-like emission achieved a maximum external quantum efficiency of 17.2%. The design strategies presented herein provide practical methods to construct efficient blue TADF dyes and realize high-performance blue TADF devices.

  3. Investigation on Al(III) and Zn(II) complexes containing a calix[4]arene bearing two 8-oxyquinoline pendant arms used as emitting materials for OLEDs

    International Nuclear Information System (INIS)

    Bagatin, Izilda A.; Legnani, Cristiano; Cremona, Marco

    2009-01-01

    A comparison between [Al·1] 3+ and [Zn·1] 2+ complexes (1 = 5,11,17,23-tetra-tert-butyl-25,27-bis[(quinoline-8-oxy)propyloxy]-26, 28-dihydroxy-calix[4]arene) has been made using electrochemical techniques and the experimental results obtained in the fabrication of organic light emitting devices (OLEDs). The electrochemically determined values of the ionization potential I p and electron affinity E a parameters for the [Al·1] 3+ (I p = 5.82eV, E a = 2.80eV) and [Zn·1] 2+ (I p = 5.67eV, E a = 2.32eV) evidenced that the [Al·1] 3+ complex is a better electron transporting layer with respect to the Zn complex one. The fabricated OLEDs based on these supramolecular complexes show a superior quality with the [Al·1] 3+ systems expected from the energy level diagrams

  4. A DRM Security Architecture for Home Networks

    NARCIS (Netherlands)

    Popescu, B.C.; Crispo, B.; Kamperman, F.L.A.J.; Tanenbaum, A.S.; Kiayias, A.; Yung, M.

    2004-01-01

    This paper describes a security architecture allowing digital rights management in home networks consisting of consumer electronic devices. The idea is to allow devices to establish dynamic groups, so called "Authorized Domains", where legally acquired copyrighted content can seamlessly move from

  5. Architectural Drawing

    DEFF Research Database (Denmark)

    Steinø, Nicolai

    2018-01-01

    In a time of computer aided design, computer graphics and parametric design tools, the art of architectural drawing is in a state of neglect. But design and drawing are inseparably linked in ways which often go unnoticed. Essentially, it is very difficult, if not impossible, to conceive of a design...... is that computers can represent graphic ideas both faster and better than most medium-skilled draftsmen, drawing in design is not only about representing final designs. In fact, several steps involving the capacity to draw lie before the representation of a final design. Not only is drawing skills an important...... prerequisite for learning about the nature of existing objects and spaces, and thus to build a vocabulary of design. It is also a prerequisite for both reflecting and communicating about design ideas. In this paper, a taxonomy of notation, reflection, communication and presentation drawing is presented...

  6. Architectural Theatricality

    DEFF Research Database (Denmark)

    Tvedebrink, Tenna Doktor Olsen; Fisker, Anna Marie; Kirkegaard, Poul Henning

    2013-01-01

    In the attempt to improve patient treatment and recovery, researchers focus on applying concepts of hospitality to hospitals. Often these concepts are dominated by hotel-metaphors focusing on host–guest relationships or concierge services. Motivated by a project trying to improve patient treatment...... is known for his writings on theatricality, understood as a holistic design approach emphasizing the contextual, cultural, ritual and social meanings rooted in architecture. Relative hereto, the International Food Design Society recently argued, in a similar holistic manner, that the methodology used...... to provide an aesthetic eating experience includes knowledge on both food and design. Based on a hermeneutic reading of Semper’s theory, our thesis is that this holistic design approach is important when debating concepts of hospitality in hospitals. We use this approach to argue for how ‘food design...

  7. Lab architecture

    Science.gov (United States)

    Crease, Robert P.

    2008-04-01

    There are few more dramatic illustrations of the vicissitudes of laboratory architecturethan the contrast between Building 20 at the Massachusetts Institute of Technology (MIT) and its replacement, the Ray and Maria Stata Center. Building 20 was built hurriedly in 1943 as temporary housing for MIT's famous Rad Lab, the site of wartime radar research, and it remained a productive laboratory space for over half a century. A decade ago it was demolished to make way for the Stata Center, an architecturally striking building designed by Frank Gehry to house MIT's computer science and artificial intelligence labs (above). But in 2004 - just two years after the Stata Center officially opened - the building was criticized for being unsuitable for research and became the subject of still ongoing lawsuits alleging design and construction failures.

  8. Modeling of charge-transport processes for predictive simulation of OLEDs

    NARCIS (Netherlands)

    Cottaar, J.

    2012-01-01

    Intensive research is taking place into alternative light sources to replace incandescent and fluorescent lamps. Organic light-emitting diodes (OLEDs) show great promise, with their main potential advantages being high energy efficiency, cheap roll-to-roll production, excellent color rendering and a

  9. The electro-thermal-mechanical performance of an OLED : a multi-physics model study

    NARCIS (Netherlands)

    Gielen, A.W.J.; Barink, M.; Brand, J. van de; Mol, A.M.B. van

    2009-01-01

    In order to study the electrical-thermo-mechanical interaction in OLEDs, finite element based simulation models were developed. Two dimensional models were used to study detailed design effects, such as the location of the bus bars, while a three dimensional model was used to study the effect of

  10. OLED Encapsulation by Room Temperature Plasma-Assisted ALD Al2O3 Films

    NARCIS (Netherlands)

    Keuning, W.; Creatore, M.; Langereis, E.; Lifka, H.; Weijer, van de P.; Sanden, van de M.C.M.

    2009-01-01

    Organic light emitting diodes (OLEDs, both small molecule and polymer LEDs) require excellent gas and moisture permeation barrier layers to increase their lifetime. The quality of the barrier layer is ultimately controlled by the presence of defects in the layer. Although a barrier layer may be

  11. Piezoelectric Lead Zirconium Titanate Composite Touch Sensors for Integration with Flexible OLED Technology

    NARCIS (Netherlands)

    Deutz, D.B.; Tempelman, E.; Zwaag, S. van der; Groen, W.A.

    2015-01-01

    To enable the design of more intuitive product user interfaces, the prospects of matching piezoelectric touch sensors with flexible organic light emitting diode (OLED) technology are investigated. Low stiffness piezoelectric composite sensors, combining piezoelectric Pb(Zr,Ti)O3 powder with a

  12. Low-frequency noise as a diagnostic tool for OLED reliability

    NARCIS (Netherlands)

    Rocha, P.R.F.; Vandamme, L.K.J.; Meskers, S.C.J.; Gomes, H.L.; Leeuw, de D.M.; Weijer, van de P.

    2013-01-01

    Organic light emitting diodes (OLED), either based on polymers or small molecules, suffer from early failure: an unpredictable sudden increase in current with a total loss of light output. This work addresses this problem using small-signal impedance measurements and electrical noise techniques.

  13. Kunstnikuks pürgija vajab paari õigeaegset impulssi / Kaido Ole, Eva Unt

    Index Scriptorium Estoniae

    Ole, Kaido

    2006-01-01

    Antonia Claudio Carvalho meistriklass "Ava oma silmad/Open Your Eyes" 23.-27. I ja näitus 27. I-9. II Eesti Kunstiakadeemia galeriis. Meistriklassist vestlesid EKA maaliosakonna juhataja Kaido Ole ja maalieriala III kursuse üliõpilane Eva Unt

  14. True-color 640 ppi OLED arrays patterned by CA i-line photolithography

    NARCIS (Netherlands)

    Malinowski, P.E.; Ke, T.; Nakamura, A.; Chang, T.-Y.; Gokhale, P.; Steudel, S.; Janssen, D.; Kamochi, Y.; Koyama, I.; Iwai,Y.; Heremans, P.

    2015-01-01

    In this paper, side-by-side patterning of red, green and blue OLEDs is demonstrated. To achieve 640 ppi arrays with 20 µm subpixel pitch, chemically amplified, i-line photoresist system with submicron resolution was used. These results show feasibility of obtaining full-color displays with

  15. White top-emitting OLEDs using organic colour-conversion layers for improved colour-stability

    Energy Technology Data Exchange (ETDEWEB)

    Schwab, Tobias; Hofmann, Simone; Thomschke, Michael; Luessem, Bjoern; Leo, Karl [Institut fuer Angewandte Photophysik, Technische Universitaet Dresden (Germany)

    2011-07-01

    In contrast to white organic light-emitting diodes (OLEDs) using several vertical stacked emitters, the principle of down-conversion gives the chance to achieve white light with a simplified layer structure and enhanced colour stability by preventing a colour shift over lifetime due to differential aging of dyes. We investigate an approach where the conversion material is integrated into a top-emitting OLED structure in a way, that only electrons can pass this layer. This assures optical excitation and avoids unwanted electrical recombination inside the conversion layer. The emission spectra, CIE-coordinates, efficiencies, and IV-characteristics depending on the conversion layer thickness have been determined and were compared to the non-emitting host-material with similar optical properties. Lifetime measurements show that these OLEDs have almost no colour change over an investigated period up to 2200 hours. It is shown that the external quantum efficiency of the OLED does not necessarily decrease with an increased conversion layer thickness, even if the photoluminescence quantum yield of these materials is below unity. This indicates that the efficiency is improved by out-coupling of isotropic re-emitted wave-guided modes.

  16. John Smith vastab / Kaido Ole, Marko Mäetamm ; interv. Harry Liivrand

    Index Scriptorium Estoniae

    Ole, Kaido

    2003-01-01

    Marko Mäetamm ja Kaido Ole, kelle kosmoseteemaline näitus "Marko and Kaido. By John Smith" on avatud Veneetsia biennaalil räägivad teemadel "koosmaalimine", "kosmoseodüsseia", "maalikunst", "kunstnikuidentiteet", "Veneetsia biennaal", "kuraatori võim", "pseudonüüm", "Eesti kunstiruum", "video" jm.

  17. Improvement of ITO properties in green-light-emitting devices by using N2:O2 plasma treatment

    Science.gov (United States)

    Jeon, Hyeonseong; Kang, Seongjong; Oh, Hwansool

    2016-01-01

    Plasma treatment reduces the roughness of the indium-tin-oxide (ITO) interface in organic light emitting diodes (OLEDs). Oxygen gas is typically used in the plasma treatment of conventional OLED devices. However, in this study, nitrogen and oxygen gases were used for surface treatment to improve the properties of ITO. To investigate the improvements resulting from the use of nitrogen and oxygen plasma treatment, fabricated green OLED devices. The device's structure was ITO (600 Å) / α-NPD (500 Å) / Alq3:NKX1595 (400 Å:20 Å,5%) / LiF / Al:Li (10 Å:1000 Å). The plasma treatment was performed in a capacitive coupled plasma (CCP) type plasma treatment chamber similar to that used in the traditional oxygen plasma treatment. The results of this study show that the combined nitrogen/oxygen plasma treatment increases the lifetime, current density, and brightness of the fabricated OLED while decreasing the operating voltage relative to those of OLEDs fabricated using oxygen plasma treatment.

  18. Overexpression of OLE1 enhances stress tolerance and constitutively activates the MAPK HOG pathway in Saccharomyces cerevisiae.

    Science.gov (United States)

    Nasution, Olviyani; Lee, Young Mi; Kim, Eunjung; Lee, Yeji; Kim, Wankee; Choi, Wonja

    2017-03-01

    OLE1 of Saccharomyces cerevisiae encodes the sole and essential Δ-9 desaturase catalyzing the conversion of saturated to unsaturated fatty acids. Upon ectopic overexpression of OLE1 in S. cerevisiae, significant increases in the membrane oleic acid content were observed. OLE1-overexpressing strains displayed enhanced tolerance to various stresses, better proton efflux, lower membrane permeability, and lessened internal hydrogen peroxide content. The OLE1-mediated enhanced stress tolerance was considerably diminished upon deletion of HOG1, which encodes the mitogen-activated protein kinase (MAPK) Hog1 of the high osmolarity glycerol (HOG) pathway. Furthermore, OLE1 overexpression constitutively activated Hog1, which remained in the cytoplasm. Hog1 activation was accomplished through the MAPK kinase kinase (MAPKKK) Ssk2, but not Ste11 and Ssk22, the other MAPKKKs of the HOG pathway. Despite its cytoplasmic location, activated Hog1 was able to activate the expression of its canonical targets, including CTT1, HSP12, and STL1, and further, the cAMP and stress response elements present in the promoter. OLE1 overexpression neither caused nor relieved endoplasmic reticulum stress. Individually or in combination, the physiological and molecular changes caused by OLE1 overexpression may contribute to enhanced tolerance to various types of stress. Biotechnol. Bioeng. 2017;114: 620-631. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

  19. Construction of Context-Based Module: How OLED can be used as a Context in High School Chemistry Instruction

    Science.gov (United States)

    Anugrah, I. R.; Mudzakir, A.; Sumarna, O.

    2017-09-01

    Teaching materials used in Indonesia generally just emphasize remembering skill so that the students’ science literacy is low. Innovation is needed to transform traditional teaching materials so that it can stimulate students’ science literacy, one of which is by context-based approach. This study focused on the construction of context-based module for high school using Organic Light-Emitting Diode (OLED) topics. OLED was chosen because it is an up-to-date topic and relevant to real life. This study used Model of Educational Reconstruction (MER) to reconstruct science content structure about OLED through combining scientist’s perspectives with student’s preconceptions and national curriculum. Literature review of OLED includes its definition, components, characteristics and working principle. Student’s preconceptions about OLED are obtained through interviews. The result shows that student’s preconceptions have not been fully similar with the scientist’s perspective. One of the reasons is that some of the related Chemistry concepts are too complicated. Through curriculum analysis, Chemistry about OLED that are appropriate for high school are Bohr’s atomic theory, redox and organic chemistry including polymers and aromatics. The OLED context and its Chemistry concept were developed into context-based module by adapting science literacy-based learning. This module is expected to increase students’ science literacy performance.

  20. Influence of the 3D-conformation, glycan component and microheterogeneity on the epitope structure of Ole e 1, the major olive allergen - Use of recombinant isoforms and specific monoclonal antibodies as immunological tools

    NARCIS (Netherlands)

    González, Eva M.; Villalba, Mayte; Lombardero, Manuel; Aalbers, Marja; van Ree, Ronald; Rodríguez, Rosalía

    2002-01-01

    Ole e 1 is the main allergen of olive pollen, which is a major cause of pollinosis in countries of the Mediterranean area. Nine Ole e 1-specific murine monoclonal antibodies (mAbs), as well as two Ole e 1-isoforms and two Ole e 1-like allergens from lilac and privet, all of them obtained in Pichia

  1. Enhancing light out-coupling of organic light-emitting devices using indium tin oxide-free low-index transparent electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Yi-Hsiang; Lu, Chun-Yang; Tsai, Shang-Ta; Tsai, Yu-Tang; Chen, Chien-Yu; Tsai, Wei-Lung; Lin, Chun-Yu; Chang, Hong-Wei; Lee, Wei-Kai; Jiao, Min; Wu, Chung-Chih, E-mail: wucc@ntu.edu.tw [Department of Electrical Engineering, Graduate Institute of Photonics and Optoelectronics, Graduate Institute of Electronics Engineering, and Innovative Photonics Advanced Research Center (i-PARC), National Taiwan University, Taipei 10617, Taiwan (China)

    2014-05-05

    With its increasing and sufficient conductivity, the conducting polymer poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) has been capable of replacing the widely used but less cost-effective indium tin oxides (ITOs) as alternative transparent electrodes for organic light-emitting devices (OLEDs). Intriguingly, PEDOT:PSS also possesses an optical refractive index significantly lower than those of ITO and typical organic layers in OLEDs and well matching those of typical OLED substrates. Optical simulation reveals that by replacing ITO with such a low-index transparent electrode, the guided modes trapped within the organic/ITO layers in conventional OLEDs can be substantially suppressed, leading to more light coupled into the substrate than the conventional ITO device. By applying light out-coupling structures onto outer surfaces of substrates to effectively extract radiation into substrates, OLEDs using such low-index transparent electrodes achieve enhanced optical out-coupling and external quantum efficiencies in comparison with conventional OLEDs using ITO.

  2. SUSTAINABLE ARCHITECTURE : WHAT ARCHITECTURE STUDENTS THINK

    OpenAIRE

    SATWIKO, PRASASTO

    2013-01-01

    Sustainable architecture has become a hot issue lately as the impacts of climate change become more intense. Architecture educations have responded by integrating knowledge of sustainable design in their curriculum. However, in the real life, new buildings keep coming with designs that completely ignore sustainable principles. This paper discusses the results of two national competitions on sustainable architecture targeted for architecture students (conducted in 2012 and 2013). The results a...

  3. Device Optimization and Transient Electroluminescence Studies of Organic light Emitting Devices

    International Nuclear Information System (INIS)

    Lijuan Zou

    2003-01-01

    Organic light emitting devices (OLEDs) are among the most promising for flat panel display technologies. They are light, bright, flexible, and cost effective. And while they are emerging in commercial product, their low power efficiency and long-term degradation are still challenging. The aim of this work was to investigate their device physics and improve their performance. Violet and blue OLEDs were studied. The devices were prepared by thermal vapor deposition in high vacuum. The combinatorial method was employed in device preparation. Both continuous wave and transient electroluminescence (EL) were studied. A new efficient and intense UV-violet light emitting device was developed. At a current density of 10 mA/cm 2 , the optimal radiance R could reach 0.38 mW/cm 2 , and the quantum efficiency was 1.25%. using the delayed EL technique, electron mobilities in DPVBi and CBP were determined to be ∼ 10 -5 cm 2 /Vs and ∼ 10 -4 cm 2 /Vs, respectively. Overshoot effects in the transient El of blue light emitting devices were also observed and studied. This effect was attributed to the charge accumulation at the organic/organic and organic/cathode interfaces

  4. Device Optimization and Transient Electroluminescence Studies of Organic light Emitting Devices

    Energy Technology Data Exchange (ETDEWEB)

    Lijuan Zou

    2003-08-05

    Organic light emitting devices (OLEDs) are among the most promising for flat panel display technologies. They are light, bright, flexible, and cost effective. And while they are emerging in commercial product, their low power efficiency and long-term degradation are still challenging. The aim of this work was to investigate their device physics and improve their performance. Violet and blue OLEDs were studied. The devices were prepared by thermal vapor deposition in high vacuum. The combinatorial method was employed in device preparation. Both continuous wave and transient electroluminescence (EL) were studied. A new efficient and intense UV-violet light emitting device was developed. At a current density of 10 mA/cm{sup 2}, the optimal radiance R could reach 0.38 mW/cm{sup 2}, and the quantum efficiency was 1.25%. using the delayed EL technique, electron mobilities in DPVBi and CBP were determined to be {approx} 10{sup -5} cm{sup 2}/Vs and {approx} 10{sup -4} cm{sup 2}/Vs, respectively. Overshoot effects in the transient El of blue light emitting devices were also observed and studied. This effect was attributed to the charge accumulation at the organic/organic and organic/cathode interfaces.

  5. Optimal thickness of hole transport layer in doped OLEDs

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Y.C.; Zhou, J.; Zhao, J.M.; Zhang, S.T.; Zhan, Y.Q.; Wang, X.Z.; Wu, Y.; Ding, X.M.; Hou, X.Y. [Fudan University, Surface Physics Laboratory (National Key Laboratory), Shanghai (China)

    2006-06-15

    Current-voltage (I-V) and electroluminescence (EL) characteristics of organic light-emitting devices with N,N'-Di-[(1-naphthalenyl)-N,N'-diphenyl]-(1,1'-biphenyl)-4,4'-diamine (NPB) of various thicknesses as the hole transport layer, and tris(8-hydroxyquinoline)aluminum (Alq{sub 3}) selectively doped with 4-(dicyanomethylene)-2-methyl-6-(p-dimethylaminostyryl)-4H-pyran (DCM) as the electron transport layer, have been investigated. A trapped charge induced band bend model is proposed to explain the I-V characteristics. It is suggested that space charge changes the injection barrier and therefore influences the electron injection process in addition to the carrier transport process. Enhanced external quantum efficiency of the devices due to the electron blocking effect of an inserted NPB layer is observed. The optimal thickness of the NPB layer is experimentally determined to be 12{+-}3 nm in doped devices, a value different from that for undoped devices, which is attributed to the electron trap effect of DCM molecules. This is consistent with the result that the proportion of Alq{sub 3} luminescence in the total electroluminescence (EL) spectra increases with NPB thickness up to 12 nm under a fixed bias. (orig.)

  6. White OLED with a single-component europium complex.

    Science.gov (United States)

    Law, Ga-Lai; Wong, Ka-Leung; Tam, Hoi-Lam; Cheah, Kok-Wai; Wong, Wing-Tak

    2009-11-16

    A new direction for white organic light-emitting devices is shown, fabricated from a novel europium complex; this single component contains a double emission center of bluish-green and red, combined to a give a pure white emission (CIE x = 0.34 and y = 0.35).

  7. Modeling Architectural Patterns Using Architectural Primitives

    NARCIS (Netherlands)

    Zdun, Uwe; Avgeriou, Paris

    2005-01-01

    Architectural patterns are a key point in architectural documentation. Regrettably, there is poor support for modeling architectural patterns, because the pattern elements are not directly matched by elements in modeling languages, and, at the same time, patterns support an inherent variability that

  8. Software architecture 2

    CERN Document Server

    Oussalah, Mourad Chabanne

    2014-01-01

    Over the past 20 years, software architectures have significantly contributed to the development of complex and distributed systems. Nowadays, it is recognized that one of the critical problems in the design and development of any complex software system is its architecture, i.e. the organization of its architectural elements. Software Architecture presents the software architecture paradigms based on objects, components, services and models, as well as the various architectural techniques and methods, the analysis of architectural qualities, models of representation of architectural templa

  9. Lightweight enterprise architectures

    CERN Document Server

    Theuerkorn, Fenix

    2004-01-01

    STATE OF ARCHITECTUREArchitectural ChaosRelation of Technology and Architecture The Many Faces of Architecture The Scope of Enterprise Architecture The Need for Enterprise ArchitectureThe History of Architecture The Current Environment Standardization Barriers The Need for Lightweight Architecture in the EnterpriseThe Cost of TechnologyThe Benefits of Enterprise Architecture The Domains of Architecture The Gap between Business and ITWhere Does LEA Fit? LEA's FrameworkFrameworks, Methodologies, and Approaches The Framework of LEATypes of Methodologies Types of ApproachesActual System Environmen

  10. Software architecture 1

    CERN Document Server

    Oussalah , Mourad Chabane

    2014-01-01

    Over the past 20 years, software architectures have significantly contributed to the development of complex and distributed systems. Nowadays, it is recognized that one of the critical problems in the design and development of any complex software system is its architecture, i.e. the organization of its architectural elements. Software Architecture presents the software architecture paradigms based on objects, components, services and models, as well as the various architectural techniques and methods, the analysis of architectural qualities, models of representation of architectural template

  11. Investigation of electrical and optical properties of MEH-PPV: ZnO nanocomposite films for OLED applications

    Energy Technology Data Exchange (ETDEWEB)

    Azhar, N. E. A., E-mail: najwaezira@yahoo.com; Shafura, A. K., E-mail: shafura@ymail.com; Affendi, I. H. H., E-mail: irmahidayanti.halim@gmail.com; Shariffudin, S. S., E-mail: sobihana@gmail.com [NANO-ElecTronic Centre, Faculty of Electrical Engineering, Universiti Teknologi MARA (UiTM), 40450 Shah Alam, Selangor (Malaysia); Saurdi, I., E-mail: saurdy788@gmail.com [Faculty of Electrical Engineering, UiTM Sarawak, Kampus Kota Meranek, Sarawak (Malaysia); Alrokayan, Salman A. H., E-mail: dr.salman@alrokayan.com; Khan, Haseeb A., E-mail: khan-haseeb@yahoo.com [Research Chair of Targeting and Treatment of Cancer Using Nanoparticles Department of Biochemistry, College of Science, King Saud University (KSU), 245 Riyadh 11454 (Saudi Arabia); Rusop, M., E-mail: rusop@salam.uitm.edu.my [NANO-ElecTronic Centre, Faculty of Electrical Engineering, Universiti Teknologi MARA (UiTM), 40450 Shah Alam, Selangor (Malaysia); NANO-SciTech Centre, Institute of Science, Universiti Teknologi MARA (UiTM), Shah Alam, Selangor (Malaysia)

    2016-07-06

    Recent investigations of the promising materials for optoelectronic have been demonstrated by introducing n-type inorganic material into conjugated polymer. The optical and electrical of nanocomposite films based on poly[2-methoxy-5-(2’-ethyl-hexyloxy)-1,4-phenylene vinylene] (MEH-PPV) and zinc oxide (ZnO) nanostructured of various deposition layers (1 to 3 layers) have been investigated. The MEH-PPV: ZnO nanocomposite films were deposited using spin-coating technique. The surface morphology nanocomposite films were characterized using field emission scanning electron microscope. From surface profiler measurement, we found that the thickness of nanocomposite films increased as deposition time increased. The optical properties were measured using photoluminescence spectroscope. The photoluminescence (PL) spectra showed that two deposition layers is the highest intensity at visible region (green emission) due to high energy transfer from particles to the polymer. The current density for two layers sample is due to aggregation of conjugated polymer chain hence form excited interchain exciton for optical excitation. This study will provide better performance and suitable for optoelectronic device especially OLEDs application.

  12. Improvement of color purity in white OLED based on Zn(HPB){sub 2} as blue emitting layer

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dong-Eun [Department of Electrical Engineering and NTRC, Dong-A University, Busan, 604-714 (Korea, Republic of); Kim, Won-Sam [Department of Chemistry and Institute of Functional Materials, Inje University, Gimhae, 621-749 (Korea, Republic of); Kim, Byoung-Sang [Department of Electrical Engineering and NTRC, Dong-A University, Busan, 604-714 (Korea, Republic of); Lee, Burm-Jong [Department of Chemistry and Institute of Functional Materials, Inje University, Gimhae, 621-749 (Korea, Republic of); Kwon, Young-Soo [Department of Electrical Engineering and NTRC, Dong-A University, Busan, 604-714 (Korea, Republic of)], E-mail: yskwon@dau.ac.kr

    2008-04-01

    We synthesized zinc (II) [2-(2-hydroxyphenyl)benzoxazole] (Zn(HPB){sub 2}) as blue emitting materials and evaluated in the organic light emitting diodes (OLEDs). The layer of Zn(HPB){sub 2} doped with 4-(dicyanomethylene)-2-t-butyl-6(1,1,7,7-tetramethyljulolidyl-9-enyl) -4H-pyran (DCJTB) (Zn(HPB){sub 2}:DCJTB) as emitters has been demonstrated. The structure of the device is indium-tin-oxide (ITO)/N,N'-bis-(1-naphthl)-diphenyl-1,1'-biphenyl-4,4'-diamine (NPB, 40 nm)/Zn(HPB){sub 2}/Zn(HPB){sub 2}:DCJTB/Alq{sub 3} (20 nm)/LiF/Al. The thickness of Zn(HPB){sub 2} layer was 0, 10, 20, 30 nm at the same time the thickness of Zn(HPB){sub 2}:DCJTB layer were 40, 30, 20, 10 nm. When thickness of Zn(HPB){sub 2} layer was 30 nm and the thickness of Zn(HPB){sub 2}:DCJTB layer was 10 nm, white emission is achieved. The Commission Internationale de l'Eclairage (CIE) coordinates of the white emission are (0.304, 0.332) at an applied voltage of 10.5 V.

  13. Extended OLED operational lifetime through phosphorescent dopant profile management

    Science.gov (United States)

    Forrest, Stephen R.; Zhang, Yifan

    2017-05-30

    This disclosure relates, at least in part, an organic light emitting device, which in some embodiments comprises an anode; a cathode; a first emissive layer disposed between the anode and the cathode, the first emissive layer comprising an electron transporting compound and a phosphorescent emissive dopant compound; and wherein the phosphorescent emissive dopant compound has a concentration gradient, in the emissive layer, which varies from the cathode side of the first emissive layer to the anode side of the emissive layer.

  14. Doped organic films for OLEDs probed with neutron reflectometry

    International Nuclear Information System (INIS)

    Smith, Arthur R. G.; Lo, Shih-Chun; Gentle, Ian R.

    2009-01-01

    Full text: Conjugated organic semiconductors form an exciting class of materials that can be used in a variety of cutting edge technologies including organic light-emitting diodes, solar cells and transistors. In all these technologies the thin film morphology and interfacial interactions are key areas for their operation. In order to optimise the materials and devices it is critical to understand the structural property relationships for the organic semiconductors by relating the 'molecular' structure to the film morphology and correlating these to the photophysical and device characteristics. Organic light emitting diodes (OLEO) have gained interest for their superior performance compared to current display technologies. Optimising the active emissive layer remains a challenge which can significantly affect the final performance of the device [1]. We have investigated the layering behaviour of small molecule co-evaporated films of deuterated 4,4'-bis(9-carbazolyl)-1, 1 '-biphenyl doped with tris-phenylpyridine iridium(llI) using neutron reflectometry The behaviour of doped emissive layers is dependent on the ratio between dopant and host material. The morphology and internal structure of such films have not yet been investigated, leading to questions about the phase separation and ordering of layers within the film.

  15. 1,2,4-Triazines in the Synthesis of Bipyridine Bisphenolate ONNO Ligands and Their Highly Luminescent Tetradentate Pt(II) Complexes for Solution-Processable OLEDs.

    Science.gov (United States)

    Pander, Piotr; Bulmer, Rachel; Martinscroft, Ross; Thompson, Stuart; Lewis, Frank W; Penfold, Thomas J; Dias, Fernando B; Kozhevnikov, Valery N

    2018-04-02

    This article describes a convenient method for the synthesis of ONNO-type tetradentate 6,6'-bis(2-phenoxy)-2,2'-bipyridine (bipyridine bisphenolate, BpyBph) ligands and their platinum(II) complexes. The methodology includes the synthesis of 1,2,4-triazine precursors followed by their transformation to functionalized pyridines by the Boger reaction. Two complementary routes employing 3,3'- and 5,5'-bis-triazines allow a modification of the central pyridine rings in different positions, which was exemplified by the introduction of cyclopentene rings. The new ligands were used to prepare highly luminescent ONNO-type Pt(II) complexes. The position of the cyclopentene rings significantly influences the solubility and photophysical properties of these complexes. Derivatives with closely positioned cyclopentene rings are soluble in organic solvents and proved to be the best candidate for solution-processable organic light-emitting devices (OLEDs), showing efficient single-dopant candlelight electroluminescence.

  16. Characterization of solution processed, p-doped films using hole-only devices and organic field-effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Swensen, James S.; Wang, Liang (Frank); Rainbolt, James E.; Koech, Phillip K.; Polikarpov, Evgueni; Gaspar, Daniel J.; Padmaperuma, Asanga B.

    2012-12-01

    We report a solution-processed approach for a p-type doped hole transport layer in organic light emitting devices (OLEDs). UV-vis-NIR absorption spectra identified the charge transfer between the donor and acceptor in the solution processed doped films. Single carrier device and field-effect transistor were utilized as test vehicles to study the charge transport property and extract important parameters such as bulk mobile carrier concentration and mobility. OLEDs with p-type doped hole transport layer showed significant improvement in power efficiency up to 30% at the optimal doping ratio. This approach has the great potential to reduce the power consumption for OLED solid state lighting while lowering the cost and boosting the throughput of its manufacturing.

  17. Magneto-electroluminescence effects in the single-layer organic light-emitting devices with macrocyclic aromatic hydrocarbons

    Directory of Open Access Journals (Sweden)

    S.-T. Pham

    2018-02-01

    Full Text Available Magneto-electroluminescence (MEL effects are observed in single-layer organic light-emitting devices (OLEDs comprising only macrocyclic aromatic hydrocarbons (MAHs. The fluorescence devices were prepared using synthesized MAHs, namely, [n]cyclo-meta-phenylene ([n]CMP, n = 5, 6. The MEL ratio of the resulting OLED is 1%–2% in the spectral wavelength range of 400-500 nm, whereas it becomes negative (−1.5% to −2% in the range from 650 to 700 nm. The possible physical origins of the sign change in the MEL are discussed. This wavelength-dependent sign change in the MEL ratio could be a unique function for future single-layer OLEDs capable of magnetic-field-induced color changes.

  18. Magneto-electroluminescence effects in the single-layer organic light-emitting devices with macrocyclic aromatic hydrocarbons

    Science.gov (United States)

    Pham, S.-T.; Ikemoto, K.; Suzuki, K. Z.; Izumi, T.; Taka, H.; Kita, H.; Sato, S.; Isobe, H.; Mizukami, S.

    2018-02-01

    Magneto-electroluminescence (MEL) effects are observed in single-layer organic light-emitting devices (OLEDs) comprising only macrocyclic aromatic hydrocarbons (MAHs). The fluorescence devices were prepared using synthesized MAHs, namely, [n]cyclo-meta-phenylene ([n]CMP, n = 5, 6). The MEL ratio of the resulting OLED is 1%-2% in the spectral wavelength range of 400-500 nm, whereas it becomes negative (-1.5% to -2%) in the range from 650 to 700 nm. The possible physical origins of the sign change in the MEL are discussed. This wavelength-dependent sign change in the MEL ratio could be a unique function for future single-layer OLEDs capable of magnetic-field-induced color changes.

  19. Unconventional device concepts for polymer solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Veenstra, S.C.; Slooff, L.H.; Verhees, W.J.H.; Cobussen-Pool, E.M.; Lenzmann, F.O.; Kroon, J.M. [ECN Solar Energy, Petten (Netherlands); Sessolo, M.; Bolink, H.J. [Instituto de Ciencia Molecular, Universidad de Valencia, Valencia (Spain)

    2009-09-15

    The inclusion of metal-oxide layers in polymer solar cells enables the fabrication of a series of unconventional device architectures. These devices include: semi-transparent polymer solar cells, devices with inverted polarity, as well as devices with air stable electrodes. A proof-of-principle of these devices is presented. The anticipated benefits of these novel device structures over conventional polymer solar cells are discussed.

  20. Enhanced light emission efficiency and current stability by morphology control and thermal annealing of organic light emitting diode devices

    Energy Technology Data Exchange (ETDEWEB)

    Caria, S [Consiglio Nazionale delle Ricerche (CNR), Istituto per lo Studio dei Materiali Nanostrutturati (ISMN), Via P Gobetti 101, 40129 Bologna (Italy); Como, E Da [Consiglio Nazionale delle Ricerche (CNR), Istituto per lo Studio dei Materiali Nanostrutturati (ISMN), Via P Gobetti 101, 40129 Bologna (Italy); Murgia, M [Consiglio Nazionale delle Ricerche (CNR), Istituto per lo Studio dei Materiali Nanostrutturati (ISMN), Via P Gobetti 101, 40129 Bologna (Italy); Zamboni, R [Consiglio Nazionale delle Ricerche (CNR), Istituto per lo Studio dei Materiali Nanostrutturati (ISMN), Via P Gobetti 101, 40129 Bologna (Italy); Melpignano, P [Centro Ricerche Plast-Optica (CRP), via Jacopo Linussio 1, 33020 Amaro (UD) (Italy); Biondo, V [Centro Ricerche Plast-Optica (CRP), via Jacopo Linussio 1, 33020 Amaro (UD) (Italy)

    2006-08-23

    The electro-optical behaviour of organic light emitting diode devices (OLEDs) is greatly influenced by the morphology of the films. A major parameter is due to the important role that the morphology of the active organic thin films plays in the phenomena that lead to light emission. For vacuum-grown OLEDs, the morphology of the specific thin films can be varied by modification of the deposition conditions. We have assessed the method (ultrahigh-vacuum organic molecular beam deposition) and conditions (variation of the deposition rate) for electro-emission (EL) optimization in a standard {alpha}-NPB (N,N'-bis-(1-naphthyl)-N,N' diphenyl-1,1' biphenyl-4-4' diamine)/Alq3 (tris-(8-hydroxyquinoline) aluminium) vacuum-grown OLED device. The best EL performances have been obtained for OLEDs made in ultrahigh vacuum with the Alq3 layer deposited with a differential deposition rate ranging from 1.0 to 0.3Angsts{sup -1}. The results are consistent with a model of different Alq3 morphologies, allowing efficient charge injection at the metal/organic interface, and of the minimization of grain boundaries at the electron-hole recombination interface, allowing efficient radiative excitonic decay. At the same time, with the objective of controlling and stabilizing the morphology changes and stabilizing the charge transport over a long OLED operating time, we have studied the effect of thermal annealing processing in the standard current behaviour of OLEDs. The large current fluctuations typically observed for standard vacuum-grown OLEDs have been smeared out and kept constant over a long operating time by the given thermal annealing conditions. The results are interpreted in terms of the stabilization of intrinsic polymorphism of the organic film's structure induced by thermal energy and leading the morphology to a lowest-energetic configuration.

  1. An architecture for an autonomous learning robot

    Science.gov (United States)

    Tillotson, Brian

    1988-01-01

    An autonomous learning device must solve the example bounding problem, i.e., it must divide the continuous universe into discrete examples from which to learn. We describe an architecture which incorporates an example bounder for learning. The architecture is implemented in the GPAL program. An example run with a real mobile robot shows that the program learns and uses new causal, qualitative, and quantitative relationships.

  2. Architectural design decisions

    NARCIS (Netherlands)

    Jansen, Antonius Gradus Johannes

    2008-01-01

    A software architecture can be considered as the collection of key decisions concerning the design of the software of a system. Knowledge about this design, i.e. architectural knowledge, is key for understanding a software architecture and thus the software itself. Architectural knowledge is mostly

  3. Information Integration Architecture Development

    OpenAIRE

    Faulkner, Stéphane; Kolp, Manuel; Nguyen, Duy Thai; Coyette, Adrien; Do, Thanh Tung; 16th International Conference on Software Engineering and Knowledge Engineering

    2004-01-01

    Multi-Agent Systems (MAS) architectures are gaining popularity for building open, distributed, and evolving software required by systems such as information integration applications. Unfortunately, despite considerable work in software architecture during the last decade, few research efforts have aimed at truly defining patterns and languages for designing such multiagent architectures. We propose a modern approach based on organizational structures and architectural description lan...

  4. Fragments of Architecture

    DEFF Research Database (Denmark)

    Bang, Jacob Sebastian

    2016-01-01

    Topic 3: “Case studies dealing with the artistic and architectural work of architects worldwide, and the ties between specific artistic and architectural projects, methodologies and products”......Topic 3: “Case studies dealing with the artistic and architectural work of architects worldwide, and the ties between specific artistic and architectural projects, methodologies and products”...

  5. Scalable devices

    KAUST Repository

    Krüger, Jens J.

    2014-01-01

    In computer science in general and in particular the field of high performance computing and supercomputing the term scalable plays an important role. It indicates that a piece of hardware, a concept, an algorithm, or an entire system scales with the size of the problem, i.e., it can not only be used in a very specific setting but it\\'s applicable for a wide range of problems. From small scenarios to possibly very large settings. In this spirit, there exist a number of fixed areas of research on scalability. There are works on scalable algorithms, scalable architectures but what are scalable devices? In the context of this chapter, we are interested in a whole range of display devices, ranging from small scale hardware such as tablet computers, pads, smart-phones etc. up to large tiled display walls. What interests us mostly is not so much the hardware setup but mostly the visualization algorithms behind these display systems that scale from your average smart phone up to the largest gigapixel display walls.

  6. Cathode architectures for alkali metal / oxygen batteries

    Science.gov (United States)

    Visco, Steven J; Nimon, Vitaliy; De Jonghe, Lutgard C; Volfkovich, Yury; Bograchev, Daniil

    2015-01-13

    Electrochemical energy storage devices, such as alkali metal-oxygen battery cells (e.g., non-aqueous lithium-air cells), have a cathode architecture with a porous structure and pore composition that is tailored to improve cell performance, especially as it pertains to one or more of the discharge/charge rate, cycle life, and delivered ampere-hour capacity. A porous cathode architecture having a pore volume that is derived from pores of varying radii wherein the pore size distribution is tailored as a function of the architecture thickness is one way to achieve one or more of the aforementioned cell performance improvements.

  7. Non-Planar Nanotube and Wavy Architecture Based Ultra-High Performance Field Effect Transistors

    KAUST Repository

    Hanna, Amir

    2016-01-01

    This dissertation also introduces a novel thin-film-transistors architecture that is named the Wavy Channel (WC) architecture, which allows for extending device width by integrating vertical fin-like substrate corrugations giving

  8. System architecture for ubiquitous live video streaming in university network environment

    CSIR Research Space (South Africa)

    Dludla, AG

    2013-09-01

    Full Text Available an architecture which supports ubiquitous live streaming for university or campus networks using a modified bluetooth inquiry mechanism with extended ID, integrated end-user device usage and adaptation to heterogeneous networks. Riding on that architecture...

  9. Polystyrene Backbone Polymers Consisting of Alkyl-Substituted Triazine Side Groups for Phosphorescent OLEDs

    Directory of Open Access Journals (Sweden)

    Beatrice Ch. D. Salert

    2012-01-01

    Full Text Available This paper describes the synthesis of new electron-transporting styrene monomers and their corresponding polystyrenes all with a 2,4,6-triphenyl-1,3,5-triazine basic structure in the side group. The monomers differ in the alkyl substitution and in the meta-/paralinkage of the triazine to the polymer backbone. The thermal and spectroscopic properties of the new electron-transporting polymers are discussed in regard to their chemical structures. Phosphorescent OLEDs were prepared using the obtained electron-transporting polymers as the emissive layer material in blend systems together with a green iridium-based emitter 13 and a small molecule as an additional cohost with wideband gap characteristics (CoH-001. The performance of the OLEDs was characterized and discussed in regard to the chemical structure of the new electron-transporting polymers.

  10. Localized Surface Plasmon-Enhanced Electroluminescence in OLEDs by Self-Assembly Ag Nanoparticle Film

    Science.gov (United States)

    He, Xiaoxiao; Wang, Wenjun; Li, Shuhong; Wang, Qingru; Zheng, Wanquan; Shi, Qiang; Liu, Yunlong

    2015-12-01

    We fabricated Ag nanoparticle (NP) film in organic light emission diodes (OLEDs), and a 23 times increase in electroluminescence (EL) at 518 nm was probed by time-resolved EL measurement. The luminance and relative external quantum efficiency (REQE) were increased by 5.4 and 3.7 times, respectively. There comes a new energy transport way that localized surface plasmons (LSPs) would absorb energy that corresponds to the electron-hole pair before recombination, promoting the formation of electron-hole pair and exciting local surface plasmon resonance (LSPR). The extended lifetime of Alq3 indicates the existence of strong interaction between LSPR and exciton, which decreases the nonradiative decay rate of OLEDs.

  11. High-throughput quantum chemistry and virtual screening for OLED material components

    Science.gov (United States)

    Halls, Mathew D.; Giesen, David J.; Hughes, Thomas F.; Goldberg, Alexander; Cao, Yixiang

    2013-09-01

    Computational structure enumeration, analysis using an automated simulation workflow and filtering of large chemical structure libraries to identify lead systems, has become a central paradigm in drug discovery research. Transferring this paradigm to challenges in materials science is now possible due to advances in the speed of computational resources and the efficiency and stability of chemical simulation packages. State-of-the-art software tools that have been developed for drug discovery can be applied to efficiently explore the chemical design space to identify solutions for problems such as organic light-emitting diode material components. In this work, virtual screening for OLED materials based on intrinsic quantum mechanical properties is illustrated. Also, a new approach to more reliably identify candidate systems is introduced that is based on the chemical reaction energetics of defect pathways for OLED materials.

  12. Modular architectures for quantum networks

    Science.gov (United States)

    Pirker, A.; Wallnöfer, J.; Dür, W.

    2018-05-01

    We consider the problem of generating multipartite entangled states in a quantum network upon request. We follow a top-down approach, where the required entanglement is initially present in the network in form of network states shared between network devices, and then manipulated in such a way that the desired target state is generated. This minimizes generation times, and allows for network structures that are in principle independent of physical links. We present a modular and flexible architecture, where a multi-layer network consists of devices of varying complexity, including quantum network routers, switches and clients, that share certain resource states. We concentrate on the generation of graph states among clients, which are resources for numerous distributed quantum tasks. We assume minimal functionality for clients, i.e. they do not participate in the complex and distributed generation process of the target state. We present architectures based on shared multipartite entangled Greenberger–Horne–Zeilinger states of different size, and fully connected decorated graph states, respectively. We compare the features of these architectures to an approach that is based on bipartite entanglement, and identify advantages of the multipartite approach in terms of memory requirements and complexity of state manipulation. The architectures can handle parallel requests, and are designed in such a way that the network state can be dynamically extended if new clients or devices join the network. For generation or dynamical extension of the network states, we propose a quantum network configuration protocol, where entanglement purification is used to establish high fidelity states. The latter also allows one to show that the entanglement generated among clients is private, i.e. the network is secure.

  13. Polystyrene Backbone Polymers Consisting of Alkyl-Substituted Triazine Side Groups for Phosphorescent OLEDs

    OpenAIRE

    Salert, Beatrice Ch. D.; Wedel, Armin; Grubert, Lutz; Eberle, Thomas; Anémian, Rémi; Krueger, Hartmut

    2012-01-01

    This paper describes the synthesis of new electron-transporting styrene monomers and their corresponding polystyrenes all with a 2,4,6-triphenyl-1,3,5-triazine basic structure in the side group. The monomers differ in the alkyl substitution and in the meta-/paralinkage of the triazine to the polymer backbone. The thermal and spectroscopic properties of the new electron-transporting polymers are discussed in regard to their chemical structures. Phosphorescent OLEDs were prepared using the obta...

  14. IT Pealinnas oled sa õnnelik: meie-aasta / Priit Kongo, Aune Past

    Index Scriptorium Estoniae

    Kongo, Priit

    2016-01-01

    2015. aasta Eesti Suhtekorralduse Auhinna konkursil pälvis sisekommunikatsiooni preemia Net Group projekti eest "IT-pealinnas oled sa õnnelik: meie-aasta", mille eesmärgiks oli ettevõtte kui hea tööandja maine kujundamine. Žürii hinnangul oli tegemist loomingulise ja oskusliku lähenemisega sisekommunikatsioonile, millega ettevõte suutis loomulikul viisil kaasata oma töötajad firma tegevustesse ja kogukondadesse

  15. Lambertian white top-emitting organic light emitting device with carbon nanotube cathode

    Science.gov (United States)

    Freitag, P.; Zakhidov, Al. A.; Luessem, B.; Zakhidov, A. A.; Leo, K.

    2012-12-01

    We demonstrate that white organic light emitting devices (OLEDs) with top carbon nanotube (CNT) electrodes show almost no microcavity effect and exhibit essentially Lambertian emission. CNT top electrodes were applied by direct lamination of multiwall CNT sheets onto white small molecule OLED stack. The devices show an external quantum efficiency of 1.5% and high color rendering index of 70. Due to elimination of the cavity effect, the devices show good color stability for different viewing angles. Thus, CNT electrodes are a viable alternative to thin semitransparent metallic films, where the strong cavity effect causes spectral shift and non-Lambertian angular dependence. Our method of the device fabrication is simple yet effective and compatible with virtually any small molecule organic semiconductor stack. It is also compatible with flexible substrates and roll-to-roll fabrication.

  16. Highly efficient tandem organic light-emitting devices employing an easily fabricated charge generation unit

    Science.gov (United States)

    Yang, Huishan; Yu, Yaoyao; Wu, Lishuang; Qu, Biao; Lin, Wenyan; Yu, Ye; Wu, Zhijun; Xie, Wenfa

    2018-02-01

    We have realized highly efficient tandem organic light-emitting devices (OLEDs) employing an easily fabricated charge generation unit (CGU) combining 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile with ultrathin bilayers of CsN3 and Al. The charge generation and separation processes of the CGU have been demonstrated by studying the differences in the current density-voltage characteristics of external-carrier-excluding devices. At high luminances of 1000 and 10000 cd/m2, the current efficiencies of the phosphorescent tandem device are about 2.2- and 2.3-fold those of the corresponding single-unit device, respectively. Simultaneously, an efficient tandem white OLED exhibiting high color stability and warm white emission has also been fabricated.

  17. Different micromanipulation applications based on common modular control architecture

    Science.gov (United States)

    Sipola, Risto; Vallius, Tero; Pudas, Marko; Röning, Juha

    2010-01-01

    This paper validates a previously introduced scalable modular control architecture and shows how it can be used to implement research equipment. The validation is conducted by presenting different kinds of micromanipulation applications that use the architecture. Conditions of the micro-world are very different from those of the macro-world. Adhesive forces are significant compared to gravitational forces when micro-scale objects are manipulated. Manipulation is mainly conducted by automatic control relying on haptic feedback provided by force sensors. The validated architecture is a hierarchical layered hybrid architecture, including a reactive layer and a planner layer. The implementation of the architecture is modular, and the architecture has a lot in common with open architectures. Further, the architecture is extensible, scalable, portable and it enables reuse of modules. These are the qualities that we validate in this paper. To demonstrate the claimed features, we present different applications that require special control in micrometer, millimeter and centimeter scales. These applications include a device that measures cell adhesion, a device that examines properties of thin films, a device that measures adhesion of micro fibers and a device that examines properties of submerged gel produced by bacteria. Finally, we analyze how the architecture is used in these applications.

  18. La Sociedad de Autores Españoles (1899-1932

    Directory of Open Access Journals (Sweden)

    Raquel Sánchez García

    2002-01-01

    Full Text Available Durante ia úitima parte dei sigio xix ios autores españoies iniciaron un movimiento asociativo en defensa de sus derechos como profesionales. El proceso culminó en la fundación de la Sociedad de Autores Españoles (precedente de la actual Sociedad General de Autores Españoles. El objetivo principal de la SAE fue conseguir para los autores la administración y gestión de los derectios derivados de sus composiciones musicales y teatrales, lo que tuvo una gran importancia en un momento en que se estaban transformando las formas de ocio en nuestro país. Estas páginas pretenden llevar a cabo un repaso de su organización, sus logros y su evolución desde 1899 hasta 1932.During the last part of xix century, Spanish authors started a movement looking after their rights as professionals in pursuit of assoclations to defend them. The process finished in the foundation of the Sociedad de Autores Españoles (precedent of the SGAE. The principal objective of the SAE was to obtain the right to manage and to negotiate their own works and compositions. This was a very important sucess because of the change of leisure in Spain. In these pages, I will try to study the organization, the achievements and the evolution of the SAE from 1899 to 1932.

  19. Security Implications of OPC, OLE, DCOM, and RPC in Control Systems

    Energy Technology Data Exchange (ETDEWEB)

    2006-01-01

    OPC is a collection of software programming standards and interfaces used in the process control industry. It is intended to provide open connectivity and vendor equipment interoperability. The use of OPC technology simplifies the development of control systems that integrate components from multiple vendors and support multiple control protocols. OPC-compliant products are available from most control system vendors, and are widely used in the process control industry. OPC was originally known as OLE for Process Control; the first standards for OPC were based on underlying services in the Microsoft Windows computing environment. These underlying services (OLE [Object Linking and Embedding], DCOM [Distributed Component Object Model], and RPC [Remote Procedure Call]) have been the source of many severe security vulnerabilities. It is not feasible to automatically apply vendor patches and service packs to mitigate these vulnerabilities in a control systems environment. Control systems using the original OPC data access technology can thus inherit the vulnerabilities associated with these services. Current OPC standardization efforts are moving away from the original focus on Microsoft protocols, with a distinct trend toward web-based protocols that are independent of any particular operating system. However, the installed base of OPC equipment consists mainly of legacy implementations of the OLE for Process Control protocols.

  20. La movilidad social de los emigrantes españoles en Europa

    Directory of Open Access Journals (Sweden)

    Antonio Alaminos

    2010-01-01

    Full Text Available La migración española de la segunda mitad del siglo XX se ha caracterizado en un primer momento por su carácter masivo y poco cualificado, seguido por un interregno de procesos de retorno y finalmente por una migración estable, no masiva pero altamente cualificada. La atención prestada a la inmigración masiva que recibe España a finales del siglo XX relegó a un segundo plano esta emigración cualificada de españoles. En este artículo se considera la relación entre movilidad espacial (migración de españoles y su posible consecuencia sobre la movilidad social ascendente que experimentan. Para ello se utilizan los datos procedentes de la encuesta internacional EIMSS (European Internal Migrations Social Survey y los procedimientos de escalamiento de clase social basados en la ocupación de Goldthorpe. El análisis se complementa con una simulación sobre la movilidad de clase, con la finalidad de visualizar y comparar los efectos sobre la movilidad social de la emigración de españoles a Francia, Alemania, Italia y Gran Bretaña.

  1. Metallic spintronic devices

    CERN Document Server

    Wang, Xiaobin

    2014-01-01

    Metallic Spintronic Devices provides a balanced view of the present state of the art of metallic spintronic devices, addressing both mainstream and emerging applications from magnetic tunneling junction sensors and spin torque oscillators to spin torque memory and logic. Featuring contributions from well-known and respected industrial and academic experts, this cutting-edge work not only presents the latest research and developments but also: Describes spintronic applications in current and future magnetic recording devicesDiscusses spin-transfer torque magnetoresistive random-access memory (STT-MRAM) device architectures and modelingExplores prospects of STT-MRAM scaling, such as detailed multilevel cell structure analysisInvestigates spintronic device write and read optimization in light of spintronic memristive effectsConsiders spintronic research directions based on yttrium iron garnet thin films, including spin pumping, magnetic proximity, spin hall, and spin Seebeck effectsProposes unique solutions for ...

  2. Experimental model for architectural systematization and its basic thermal performance. Part 1. Research on architectural systematization of energy conversion devices; Kenchiku system ka model no gaiyo to kihon seino ni tsuite. 1. Energy henkan no kenchiku system ka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Sunaga, N; Ito, N; Kimura, G; Fukao, S; Shimizu, T; Tsunoda, M; Muro, K [Tokyo Metropolitan University, Tokyo (Japan)

    1996-10-27

    The outline of a model for architectural systematization of natural energy conversion and the experiment result on the basic thermal performance in winter are described. The model is about 20 m{sup 2} in floor space. Foam polystyrene of 100 mm and 200 mm thick was used for the outer wall as heat insulating materials. The model has a solar battery and air conditioner and uses red brick as a heat reservoir. An experiment was made on seven modes obtained when three elements (heating, heat storage, and night insulated door) are combined. The information obtained by the experiment showed that a model for architectural systematization has high heat insulation and tightness and can be used as an energy element or an evaluation model for architectural systematization. In this model for architectural systematization, the power consumption of an air conditioner in winter can be fully supplied by only the power generation based on a solar battery. In an architectural element, the heating energy consumption can be remarkably reduced and the indoor thermal environment can be greatly improved, by the combination of a heat reservoir and night heat insulated door. 1 ref., 6 figs., 3 tabs.

  3. Luminance mechanisms in green organic light-emitting devices fabricated utilizing tris(8-hydroxyquinoline)aluminum/4,7-diphenyl-1, 10-phenanthroline multiple heterostructures acting as an electron transport layer.

    Science.gov (United States)

    Choo, Dong Chul; Seo, Su Yul; Kim, Tae Whan; Jin, You Young; Seo, Ji Hyun; Kim, Young Kwan

    2010-05-01

    The electrical and the optical properties in green organic light-emitting devices (OLEDs) fabricated utilizing tris(8-hydroxyquinoline)aluminum (Alq3)/4,7-diphenyl-1,10-phenanthroline (BPhen) multiple heterostructures acting as an electron transport layer (ETL) were investigated. The operating voltage of the OLEDs with a multiple heterostructure ETL increased with increasing the number of the Alq3/BPhen heterostructures because more electrons were accumulated at the Alq3/BPhen heterointerfaces. The number of the leakage holes existing in the multiple heterostructure ETL of the OLEDs at a low voltage range slightly increased due to an increase of the internal electric field generated from the accumulated electrons at the Alq3/BPhen heterointerface. The luminance efficiency of the OLEDs with a multiple heterostructure ETL at a high voltage range became stabilized because the increase of the number of the heterointerface decreased the quantity of electrons accumulated at each heterointerface.

  4. Low power adder based auditory filter architecture.

    Science.gov (United States)

    Rahiman, P F Khaleelur; Jayanthi, V S

    2014-01-01

    Cochlea devices are powered up with the help of batteries and they should possess long working life to avoid replacing of devices at regular interval of years. Hence the devices with low power consumptions are required. In cochlea devices there are numerous filters, each responsible for frequency variant signals, which helps in identifying speech signals of different audible range. In this paper, multiplierless lookup table (LUT) based auditory filter is implemented. Power aware adder architectures are utilized to add the output samples of the LUT, available at every clock cycle. The design is developed and modeled using Verilog HDL, simulated using Mentor Graphics Model-Sim Simulator, and synthesized using Synopsys Design Compiler tool. The design was mapped to TSMC 65 nm technological node. The standard ASIC design methodology has been adapted to carry out the power analysis. The proposed FIR filter architecture has reduced the leakage power by 15% and increased its performance by 2.76%.

  5. Low Power Adder Based Auditory Filter Architecture

    Directory of Open Access Journals (Sweden)

    P. F. Khaleelur Rahiman

    2014-01-01

    Full Text Available Cochlea devices are powered up with the help of batteries and they should possess long working life to avoid replacing of devices at regular interval of years. Hence the devices with low power consumptions are required. In cochlea devices there are numerous filters, each responsible for frequency variant signals, which helps in identifying speech signals of different audible range. In this paper, multiplierless lookup table (LUT based auditory filter is implemented. Power aware adder architectures are utilized to add the output samples of the LUT, available at every clock cycle. The design is developed and modeled using Verilog HDL, simulated using Mentor Graphics Model-Sim Simulator, and synthesized using Synopsys Design Compiler tool. The design was mapped to TSMC 65 nm technological node. The standard ASIC design methodology has been adapted to carry out the power analysis. The proposed FIR filter architecture has reduced the leakage power by 15% and increased its performance by 2.76%.

  6. Kinetic Monte Carlo modeling of the efficiency roll-off in a multilayer white organic light-emitting device

    NARCIS (Netherlands)

    Mesta, M.; van Eersel, H.; Coehoorn, R.; Bobbert, P.A.

    2016-01-01

    Triplet-triplet annihilation (TTA) and triplet-polaron quenching (TPQ) in organic light-emitting devices (OLEDs) lead to a roll-off of the internal quantum efficiency (IQE) with increasing current density J. We employ a kinetic Monte Carlo modeling study to analyze the measured IQE and color balance

  7. Modeling Architectural Patterns’ Behavior Using Architectural Primitives

    NARCIS (Netherlands)

    Waqas Kamal, Ahmad; Avgeriou, Paris

    2008-01-01

    Architectural patterns have an impact on both the structure and the behavior of a system at the architecture design level. However, it is challenging to model patterns’ behavior in a systematic way because modeling languages do not provide the appropriate abstractions and because each pattern

  8. Comparison study of transparent RF-sputtered ITO/AZO and ITO/ZnO bilayers for near UV-OLED applications

    Science.gov (United States)

    Rezaie, Mahdiyar Nouri; Manavizadeh, Negin; Abadi, Ehsan Mohammadi Nasr; Nadimi, Ebrahim; Boroumand, Farhad Akbari

    2017-01-01

    Hybrid inorganic/organic light-emitting diodes have attracted much attention in the field of luminescent electronics due to the desired incorporation of high optoelectronic features of inorganic materials with the processability and variety of organic polymers. To generate and emit a near ultraviolet (N-UV) ray, wide band gap semiconductors can be applied in the organic light-emitting diodes (OLEDs). In this paper, zinc oxide (ZnO) and aluminum-doped ZnO (AZO) thin films are deposited by radio frequency (RF) sputtering above the ITO electrode and poly [2-methoxy-5-(2-ethyl-hexyloxy)-1,4-phenylene-vinylene] (MEH-PPV) conjugated polymer is utilized as a complementary p-type semiconductor in OLED structure. The impact of ZnO and AZO thickness on the structural, electrical, optical and morphological properties of ITO/AZO and ITO/ZnO bilayers are scrutinized and compared. Results show that with the enlargement of both ZnO and AZO film thickness, the physical properties are gradually improved resulting in the better quality of transparent conducting thin film. The average electrical resistivity of 8.4 × 10-4 and 1.1 × 10-3 Ω-cm, average sheet resistance of 32.9 and 42.3 Ω/sq, average transmittance of 88.3 and 87.3% and average FOM of 1.0 × 104 and 7.4 × 103 (Ω-cm)-1 are obtained for ITO/AZO and ITO/ZnO bilayers, respectively. Moreover, comparing the results indicates that the strain and the stress within the ITO/AZO bilayer are decreased nearly 19% with respect to ITO/ZnO bilayer which yield higher quality of crystal. Consequently, the physical properties of ITO/AZO bilayer is found to be superior regarding ITO/ZnO bilayer. For fabricated UV-OLEDs, the turn-on voltages, the characteristic energy (Et) and the total concentration of traps (Nt) for the devices with the structures of ITO/ZnO/MEH-PPV/Al and ITO/AZO/MEH-PPV/Al are obtained 12 and 14 V, 0.108 and 0.191 eV, 9.33 × 1016 and 5.22 × 1016 cm-3, respectively. Furthermore, according to the electroluminescence

  9. Organic Optoelectronic Devices Employing Small Molecules

    Science.gov (United States)

    Fleetham, Tyler Blain

    Organic optoelectronic devices have remained a research topic of great interest over the past two decades, particularly in the development of efficient organic photovoltaics (OPV) and organic light emitting diodes (OLED). In order to improve the efficiency, stability, and materials variety for organic optoelectronic devices a number of emitting materials, absorbing materials, and charge transport materials were developed and employed in a device setting. Optical, electrical, and photophysical studies of the organic materials and their corresponding devices were thoroughly carried out. Two major approaches were taken to enhance the efficiency of small molecule based OPVs: developing material with higher open circuit voltages or improved device structures which increased short circuit current. To explore the factors affecting the open circuit voltage (VOC) in OPVs, molecular structures were modified to bring VOC closer to the effective bandgap, DeltaE DA, which allowed the achievement of 1V VOC for a heterojunction of a select Ir complex with estimated exciton energy of only 1.55eV. Furthermore, the development of anode interfacial layer for exciton blocking and molecular templating provide a general approach for enhancing the short circuit current. Ultimately, a 5.8% PCE was achieved in a single heterojunction of C60 and a ZnPc material prepared in a simple, one step, solvent free, synthesis. OLEDs employing newly developed deep blue emitters based on cyclometalated complexes were demonstrated. Ultimately, a peak EQE of 24.8% and nearly perfect blue emission of (0.148,0.079) was achieved from PtON7dtb, which approaches the maximum attainable performance from a blue OLED. Furthermore, utilizing the excimer formation properties of square-planar Pt complexes, highly efficient and stable white devices employing a single emissive material were demonstrated. A peak EQE of over 20% for pure white color (0.33,0.33) and 80 CRI was achieved with the tridentate Pt complex, Pt

  10. Electron-transporting layer doped with cesium azide for high-performance phosphorescent and tandem white organic light-emitting devices

    Science.gov (United States)

    Yu, Yaoyao; Chen, Xingming; Jin, Yu; Wu, Zhijun; Yu, Ye; Lin, Wenyan; Yang, Huishan

    2017-07-01

    Cesium azide was employed as an effective n-dopant in the electron-transporting layer (ETL) of organic light-emitting devices (OLEDs) owing to its low deposition temperature and high ambient stability. By doping cesium azide onto 4,7-diphenyl-1,10-phenanthroline, a green phosphorescent OLED having best efficiencies of 66.25 cd A-1, 81.22 lm W-1 and 18.82% was realized. Moreover, the efficiency roll-off from 1000 cd m-2 to 10 000 cd m-2 is only 12.9%, which is comparable with or even lower than that of devices utilizing the co-host system. Physical mechanisms for the improvement of device performance were studied in depth by analyzing the current density-voltage (J-V) characteristics of the electron-only devices. In particular, by comparing the J-V characteristics of the electron-only devices instead of applying the complicated ultraviolet photoelectron spectrometer measurements, we deduced the decrease in barrier height for electron injection at the ETL/cathode contact. Finally, an efficient tandem white OLED utilizing the n-doped layer in the charge generation unit (CGU) was constructed. As far as we know, this is the first report on the application of this CGU for fabricating tandem white OLEDs. The emissions of the tandem device are all in the warm white region from 1213 cd m-2 to 10870 cd m-2, as is beneficial to the lighting application.

  11. Instruction Set Architectures for Quantum Processing Units

    OpenAIRE

    Britt, Keith A.; Humble, Travis S.

    2017-01-01

    Progress in quantum computing hardware raises questions about how these devices can be controlled, programmed, and integrated with existing computational workflows. We briefly describe several prominent quantum computational models, their associated quantum processing units (QPUs), and the adoption of these devices as accelerators within high-performance computing systems. Emphasizing the interface to the QPU, we analyze instruction set architectures based on reduced and complex instruction s...

  12. Religious architecture: anthropological perspectives

    NARCIS (Netherlands)

    Verkaaik, O.

    2013-01-01

    Religious Architecture: Anthropological Perspectives develops an anthropological perspective on modern religious architecture, including mosques, churches and synagogues. Borrowing from a range of theoretical perspectives on space-making and material religion, this volume looks at how religious

  13. Avionics Architecture for Exploration

    Data.gov (United States)

    National Aeronautics and Space Administration — The goal of the AES Avionics Architectures for Exploration (AAE) project is to develop a reference architecture that is based on standards and that can be scaled and...

  14. RATS: Reactive Architectures

    National Research Council Canada - National Science Library

    Christensen, Marc

    2004-01-01

    This project had two goals: To build an emulation prototype board for a tiled architecture and to demonstrate the utility of a global inter-chip free-space photonic interconnection fabric for polymorphous computer architectures (PCA...

  15. Rhein-Ruhr architecture

    DEFF Research Database (Denmark)

    2002-01-01

    katalog til udstillingen 'Rhein - Ruhr architecture' Meldahls smedie, 15. marts - 28. april 2002. 99 sider......katalog til udstillingen 'Rhein - Ruhr architecture' Meldahls smedie, 15. marts - 28. april 2002. 99 sider...

  16. Architecture and Film

    OpenAIRE

    Mohammad Javaheri, Saharnaz

    2016-01-01

    Film does not exist without architecture. In every movie that has ever been made throughout history, the cinematic image of architecture is embedded within the picture. Throughout my studies and research, I began to see that there is no director who can consciously or unconsciously deny the use of architectural elements in his or her movies. Architecture offers a strong profile to distinguish characters and story. In the early days, films were shot in streets surrounde...

  17. Bacterial cellulose membrane as flexible substrate for organic light emitting devices

    International Nuclear Information System (INIS)

    Legnani, C.; Vilani, C.; Calil, V.L.; Barud, H.S.; Quirino, W.G.; Achete, C.A.; Ribeiro, S.J.L.; Cremona, M.

    2008-01-01

    Bacterial cellulose (BC) membranes produced by gram-negative, acetic acid bacteria (Gluconacetobacter xylinus), were used as flexible substrates for the fabrication of Organic Light Emitting Diodes (OLED). In order to achieve the necessary conductive properties indium tin oxide (ITO) thin films were deposited onto the membrane at room temperature using radio frequency (r.f.) magnetron sputtering with an r.f. power of 30 W, at pressure of 8 mPa in Ar atmosphere without any subsequent thermal treatment. Visible light transmittance of about 40% was observed. Resistivity, mobility and carrier concentration of deposited ITO films were 4.90 x 10 -4 Ohm cm, 8.08 cm 2 /V-s and - 1.5 x 10 21 cm -3 , respectively, comparable with commercial ITO substrates. In order to demonstrate the feasibility of devices based on BC membranes three OLEDs with different substrates were produced: a reference one with commercial ITO on glass, a second one with a SiO 2 thin film interlayer between the BC membrane and the ITO layer and a third one just with ITO deposited directly on the BC membrane. The observed OLED luminance ratio was: 1; 0.5; 0.25 respectively, with 2400 cd/m 2 as the value for the reference OLED. These preliminary results show clearly that the functionalized biopolymer, biodegradable, biocompatible bacterial cellulose membranes can be successfully used as substrate in flexible organic optoelectronic devices

  18. [The role of BCP in electroluminescence of multilayer organic light-emitting devices].

    Science.gov (United States)

    Deng, Zhao-Ru; Yang, Sheng-Yi; Lou, Zhi-Dong; Meng, Ling-Chuan

    2009-03-01

    As a hole-blocking layer, 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP) is usually used in blue and white light electroluminescent devices. The ability of blocking holes of BCP layer depends on its thickness, and basically holes can tunnel through thin BCP layer. In order to know the role of BCP layer in electroluminescence (EL) of multilayer organic light-emitting diodes (OLEDs), in the present paper, the authors designed a multilayer OLED ITO/NPB/BCP/Alq3 : DCJTB/Alq3/Al and investigated the influence of thickness of BCP on the EL spectra of multilayer OLEDs at different applied voltages. The experimental data show that thin BCP layer can block holes partially and tune the energy transfer between different emissive layers, and in this way, it is easy to obtain white emission, but its EL spectra will change with the applied voltages. The EL spectra of multilayer device will remain relatively stable when BCP layer is thick enough, and the holes can hardly tunnel through when the thickness of BCP layer is more than 15 nm. Furthermore, the stability of EL spectra of the multilayer OLED at different applied voltages was discussed.

  19. SecureCore Software Architecture: Trusted Path Application (TPA) Requirements

    National Research Council Canada - National Science Library

    Clark, Paul C; Irvine, Cynthia E; Levin, Timothy E; Nguyen, Thuy D; Vidas, Timothy M

    2007-01-01

    .... The purpose of the SecureCore research project is to investigate fundamental architectural features required for the trusted operation of mobile computing devices so the security is built-in, transparent and flexible...

  20. Elements of Architecture

    DEFF Research Database (Denmark)

    Elements of Architecture explores new ways of engaging architecture in archaeology. It conceives of architecture both as the physical evidence of past societies and as existing beyond the physical environment, considering how people in the past have not just dwelled in buildings but have existed...