WorldWideScience

Sample records for oil production structures

  1. Structural Lightweight Concrete Production by Using Oil Palm Shell

    Directory of Open Access Journals (Sweden)

    Habibur Rahman Sobuz

    2014-01-01

    Full Text Available Conventional building materials are widely used in a developing country like Malaysia. This type of material is costly. Oil palm shell (OPS is a type of farming solid waste in the tropical region. This paper aims to investigate strength characteristics and cost analysis of concrete produced using the gradation of OPS 0–50% on conventional coarse aggregate with the mix proportions 1 : 1.65 : 2.45, 1 : 2.5 : 3.3, and 1 : 3.3 : 4.2 by the weight of ordinary Portland cement, river sand, crushed stone, and OPS as a substitution for coarse aggregate. The corresponding w/c ratios were used: 0.45, 0.6, and 0.75, respectively, for the defined mix proportions. Test results indicate that compressive strength of concrete decreased as the percentage of the OPS increased in each mix ratio. Other properties of OPS concrete, namely, modulus of rupture, modulus of elasticity, splitting tensile strength, and density, were also determined and compared to the corresponding properties of conventional concrete. Economic analysis also indicates possible cost reduction of up to 15% due to the use of OPS as coarse aggregate. Finally, it is concluded that the use of OPS has great potential in the production of structural lightweight concrete.

  2. Rheology of Structured Oils

    Science.gov (United States)

    Kelbaliev, G. I.; Rasulov, S. R.; Rzaev, A. G.; Mustafaeva, G. R.

    2017-07-01

    Rheological models of structured oils are proposed and compared with available experimental data on oils from different deposits. It is shown that structured oils can possess properties of Bingham and power-law non-Newtonian fluids.

  3. China's Two Oil Giants Halt Oil Products Exports

    Institute of Scientific and Technical Information of China (English)

    Yin Xian

    2008-01-01

    @@ CNPC, China's largest oil producer, and Sinopec, the nation's largest refiner expressed they would increase their oil processing and halt oil products exports in the third quarter to ensure domestic supply. Vice president of CNPC Wang Yilin said on June 2 that CNPC would stop oil products export and increase the imports to secure the domestic market supplies. Meanwhile, Sinopec President Wang Tianpu also said that Sinopec would raise production, halt exports and adjust product structure to ensure domestic supply, especially for the reconstruction after the earthquake, the summer harvest and the Olympic Games.

  4. Production of vegetable oil blends and structured lipids and their effect on wound healing

    Directory of Open Access Journals (Sweden)

    Juliana Neves Rodrigues Ract

    2015-06-01

    Full Text Available Two oil blends (sunflower/canola oils 85/15 (BL1 and canola/linseed oils 70/30 (BL2, were prepared and enzymatically interesterified to be applied to surgically-induced wounds in rats. Following surgery, the animals were submitted to the Treatment with Physiological Saline (TPS (control group, Blends (TBL, and Structured Lipids (TSL. The control group (TPS received physiological saline solution for 15 days. In TBL, BL1 was administered during the inflammation phase (days 0-3 and BL2 in the tissue formation and remodeling phase (days 4-15. In TSL, Structured Lipid 1 (SL1 and Structured Lipid 2 (SL2 were used instead of BL1 and BL2, respectively. The aim of this study was to compare wound closure evolution among rats treated with the blends or structured lipids versus control rats treated with physiological saline. The wound healing process was evaluated by measuring the wound areas along the treatments and the concentrations of cytokines. An increase in the areas of wounds treated with the blends and structured lipids in the inflammatory phase was observed, followed by a steeper closure curve compared to wounds treated with physiological saline. The changes observed during the inflammatory phase suggest a potential therapeutic application in cutaneous wound healing which should be further investigated.

  5. Oleogels, a promising structured oil for decreasing saturated fatty acid concentrations: Production and food-based applications.

    Science.gov (United States)

    Pehlivanoğlu, Halime; Demirci, Mehmet; Toker, Omer Said; Konar, Nevzat; Karasu, Salih; Sagdic, Osman

    2016-11-10

    Oils and fats are widely used in the food formulations in order to improve nutritional and some quality characteristics of food products. Solid fats produced from oils by hydrogenization, interesterification, and fractionation processes are widely used in different foodstuffs for these aims. In recent years, consumer awareness of relation between diet and health has increased which can cause worry about solid fat including products in terms of their high saturated fatty acid and trans fatty acid contents. Therefore, different attempts have been carried out to find alternative ways to produce solid fat with low saturated fatty acid content. One of the promising ways is using oleogels, structuring oils with oleogelators. In this review, history, raw materials and production methods of the oleogels and their functions in oleogel quality were mentioned. Moreover, studies related with oleogel usage in different products were summarized and positive and negative aspects of oleogel were also mentioned. Considering the results of the related studies, it can be concluded that oleogels can be used in the formulation of bakery products, breakfast spreads, margarines, chocolates and chocolate-derived products and some of the meat products.

  6. Potential use of avocado oil on structured lipids MLM-type production catalysed by commercial immobilised lipases.

    Science.gov (United States)

    Caballero, Eduardo; Soto, Carmen; Olivares, Araceli; Altamirano, Claudia

    2014-01-01

    Structured Lipids are generally constituents of functional foods. Growing demands for SL are based on a fuller understanding of nutritional requirements, lipid metabolism, and improved methods to produce them. Specifically, this work was aimed to add value to avocado oil by producing dietary triacylglycerols (TAG) containing medium-chain fatty acids (M) at positions sn-1,3 and long-chain fatty acids (L) at position sn-2. These MLM-type structured lipids (SL) were produced by interesterification of caprylic acid (CA) (C8:0) and avocado oil (content of C18:1). The regiospecific sn-1,3 commercial lipases Lipozyme RM IM and TL IM were used as biocatalysts to probe the potential of avocado oil to produce SL. Reactions were performed at 30-50°C for 24 h in solvent-free media with a substrate molar ratio of 1∶2 (TAG:CA) and 4-10% w/w enzyme content. The lowest incorporation of CA (1.1% mol) resulted from Lipozyme RM IM that was incubated at 50°C. The maximum incorporation of CA into sn-1,3 positions of TAG was 29.2% mol. This result was obtained at 30°C with 10% w/w Lipozyme TL IM, which is the highest values obtained in solvent-free medium until now for structured lipids of low-calories. This strategy opens a new market to added value products based on avocado oil.

  7. Potential use of avocado oil on structured lipids MLM-type production catalysed by commercial immobilised lipases.

    Directory of Open Access Journals (Sweden)

    Eduardo Caballero

    Full Text Available Structured Lipids are generally constituents of functional foods. Growing demands for SL are based on a fuller understanding of nutritional requirements, lipid metabolism, and improved methods to produce them. Specifically, this work was aimed to add value to avocado oil by producing dietary triacylglycerols (TAG containing medium-chain fatty acids (M at positions sn-1,3 and long-chain fatty acids (L at position sn-2. These MLM-type structured lipids (SL were produced by interesterification of caprylic acid (CA (C8:0 and avocado oil (content of C18:1. The regiospecific sn-1,3 commercial lipases Lipozyme RM IM and TL IM were used as biocatalysts to probe the potential of avocado oil to produce SL. Reactions were performed at 30-50°C for 24 h in solvent-free media with a substrate molar ratio of 1∶2 (TAG:CA and 4-10% w/w enzyme content. The lowest incorporation of CA (1.1% mol resulted from Lipozyme RM IM that was incubated at 50°C. The maximum incorporation of CA into sn-1,3 positions of TAG was 29.2% mol. This result was obtained at 30°C with 10% w/w Lipozyme TL IM, which is the highest values obtained in solvent-free medium until now for structured lipids of low-calories. This strategy opens a new market to added value products based on avocado oil.

  8. HEAVY OIL DEVELOPMENT KEY TO CHINA'S OIL PRODUCTION GROWTH

    Institute of Scientific and Technical Information of China (English)

    Ma Chunpeng

    2006-01-01

    @@ How to raise the heavy oil production rate has long been a difficult research project focused by international oil giants while the super-heavy oil development is particularly a world-class bottleneck for many oil producers. However, China's main oil companies will give priority to heavy oil exploration and production in the next decade to meet China's increasing energy needs.

  9. Environmental emergency in the oil production and oil products transport

    Directory of Open Access Journals (Sweden)

    Jozef Čopan

    2006-10-01

    Full Text Available The paper refers to the experience of the environmental emergency response in the case of accidental leakages of oil or oil products into the environment. The gained experience is demonstrated on four different sites where the remediation of contaminated soil / groundwater and emergency response were carried out by the Czech environmental company DEKONTA a.s.

  10. Biodiesel production from palm oil

    Directory of Open Access Journals (Sweden)

    Kiatsimkul, P.

    2001-11-01

    Full Text Available Methyl ester was produced from many sources of oil palm products, namely used frying oil, RBD palm oil, degummed and deacidified palm oil, palm stearin and superhard palm stearin. Production process was a conventional transesterification batch process using methanol as reactant and sodium hydroxide as catalyst. Production procedure consisted of oil preparation, solvent preparation, reaction step, glycerol separation, washing step and finishing step. Thin layer chromatograph was used to determine the composition of product and nearly 100% methyl ester was obtained at a suitable condition. Molar ratio of oil: methanol was about 1:6, which equal to 20% by weight of methanol. Sodium hydroxide was 0.5-1 %wt. of oil. The production temperature was 60-80ºC, mixing time was only 15-30 minutes and reaction time was 3-4 hours. Many fuel properties of methyl ester were very close to high-speed diesel such as viscosity, density, heating value and boiling point range. Pour point of methyl ester was higher than diesel owing to the high composition of saturated methyl ester that has a high melting point.

  11. Coal Liquefaction characteristics and chemical structure of product oil; Sekitan ekika hanno tokusei to seiseibutsu no kagaku kozo

    Energy Technology Data Exchange (ETDEWEB)

    Endo, H.; Sato, M.; Chiba, T.; Hattori, H. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology; Sasaki, M. [Hokkaido National Industrial Research Institute, Sapporo (Japan)

    1996-10-28

    Through the hydrogenolysis of Wandoan coal and Tanito Harum coal which are used for the NEDOL process, differences of liquefaction characteristics between them were found. The purpose of this study is to grasp these differences as differences of chemical structures of oil fractions. The compound type analysis was conducted for oil fractions obtained at varied reaction temperature for varied reaction time. Coal liquefaction characteristics of these coals were discussed by relating oil yields and chemical structures. For Tanito Harum coal, yields of gas and oil were considered to be lower than those for Wandoan coal, which reflected that the contents of partially hydrogenated hydroaromatics in oil fraction from the former were lower than those from the latter, and that the remarkable change of composition did not occur with the progress of the reaction. For both the coals, the remarkable changes in the average molecular weight of oil fraction were not observed with the progress of the reaction. While, the content of methane gradually increased with the progress of the reaction, which suggested that oil was gradually dealkylated. 5 figs.

  12. Bisulfite pretreatment changes the structure and properties of oil palm empty fruit bunch to improve enzymatic hydrolysis and bioethanol production.

    Science.gov (United States)

    Tan, Liping; Sun, Wan; Li, Xuezhi; Zhao, Jian; Qu, Yinbo; Choo, Yuen May; Loh, Soh Kheang

    2015-06-01

    Bisulfite pretreatment is a proven effective method for improving the enzymatic hydrolysis of empty fruit bunch (EFB) from oil palm for bioethanol production. In this study, we set out to determine the changes that occur in the structure and properties of EFB materials and fractions of hemicellulose and lignin during the bisulfite pretreatment process. The results showed that the crystallinity of cellulose in EFB increased after bisulfite pretreatment, whereas the EFB surface was damaged to various degrees. The orderly structure of EFB, which was maintained by hydrogen bonds, was destroyed by bisulfite pretreatment. Bisulfite pretreatment also hydrolyzed the glycosidic bonds of the xylan backbone of hemicellulose, thereby decreasing the molecular weight and shortening the xylan chains. The lignin fractions obtained from EFB and pretreated EFB were typically G-S lignin, and with low content of H units. Meanwhile, de-etherification occurred at the β-O-4 linkage, which was accompanied by polymerization and demethoxylation as a result of bisulfite pretreatment. The adsorption ability of cellulase differed for the various lignin fractions, and the water-soluble lignin fractions had higher adsorption capacity on cellulase than the milled wood lignin. In general, the changes in the structure and properties of EFB provided insight into the benefits of bisulfite pretreatment.

  13. Natural cold pressed oils as cosmetic products

    Directory of Open Access Journals (Sweden)

    Małgorzata Ligęza

    2016-12-01

    Full Text Available Background. It seems that patients may ask general practitioners about natural cosmetics applied on the skin regarding their safety and suitability. Objectives. The aim of the study was to analyze natural cold pressed oils as potential cosmetic products. Material and methods. Cold pressed oils obtained from selected seeds and fruit stones were analyzed, including: chokeberry seed oil, blackcurrant seed oil, elderberry seed oil, raspberry seed oil, apricot seed oil, tomato seed oil, strawberry seed oil, broccoli seed oil, Nigella sativa seed oil, hemp oil, safflower seed oil, Silybum marianum seed oil and coconut oil. 80 adult volunteers assessed the cosmetic properties of the analyzed oils. Each of the volunteers tested 2 to 4 different oils, by applying them on the skin. In addition, patch tests with all analyzed oils were performed on 23 individuals. Results. The majority of tested oils were positively evaluated by the participants: in the opinion of the participants, oil extracted from safflower had the best appearance (100% positive opinions, coconut oil had the best smell (70% positive opinions, while black currant seed oil showed the best absorbency (85% positive opinions. No irritation was observed within the analyzed product group, albeit one allergic reaction to apricot seed oil was observed with patch testing. Conclusions . Based on the achieved results, it could be suggested that natural cold pressed oils can be applied to the skin as cosmetics. Our observations may be helpful for general practitioners when choosing natural cosmetics.

  14. Formulation of soy oil products

    Directory of Open Access Journals (Sweden)

    Woerfel, John B.

    1995-12-01

    Full Text Available The paper comments different formulations of soy oil products such as salad and cooking oils, margarine, shortenings, commercial shortenings, frying shortenings, and fluid shortenings. Hydrogenation and its influence on final products is also included.

    El trabajo presenta diferentes formulaciones a base de aceite de soja tales como aceites para ensalada y cocinado, margarina, grasas sólidas (shortenings, grasas sólidas comerciales, grasas sólidas para frituras y grasas fluidas. Hace también referencia al proceso de hidrogenación y a sus efectos en los productos finales.

  15. A Structure Identification and Toxicity Assessment of the Degradation Products of Aflatoxin B1 in Peanut Oil under UV Irradiation

    Science.gov (United States)

    Mao, Jin; He, Bing; Zhang, Liangxiao; Li, Peiwu; Zhang, Qi; Ding, Xiaoxia; Zhang, Wen

    2016-01-01

    Aflatoxins, a group of extremely hazardous compounds because of their genotoxicity and carcinogenicity to human and animals, are commonly found in many tropical and subtropical regions. Ultraviolet (UV) irradiation is proven to be an effective method to reduce or detoxify aflatoxins. However, the degradation products of aflatoxins under UV irradiation and their safety or toxicity have not been clear in practical production such as edible oil industry. In this study, the degradation products of aflatoxin B1 (AFB1) in peanut oil were analyzed by Ultra Performance Liquid Chromatograph-Thermo Quadrupole Exactive Focus mass spectrometry/mass spectrometry (UPLC-TQEF-MS/MS). The high-resolution mass spectra reflected that two main products were formed after the modification of a double bond in the terminal furan ring and the fracture of the lactone ring, while the small molecules especially nitrogen-containing compound may have participated in the photochemical reaction. According to the above results, the possible photodegradation pathway of AFB1 in peanut oil is proposed. Moreover, the human embryo hepatocytes viability assay indicated that the cell toxicity of degradation products after UV irradiation was much lower than that of AFB1, which could be attributed to the breakage of toxicological sites. These findings can provide new information for metabolic pathways and the hazard assessment of AFB1 using UV detoxification. PMID:27845743

  16. Structure elucidation of C80, C81 and C82 isoprenoid tetraacids responsible for naphthenate deposition in crude oil production.

    Science.gov (United States)

    Lutnaes, Bjart F; Krane, Jostein; Smith, Ben E; Rowland, Steven J

    2007-06-21

    A series of C(80) isoprenoid 20-bis-16,16'-biphytanyl tetraacids has previously been found to be responsible for calcium naphthenate scaling in crude oil processing. This paper describes the structure elucidation by high-field NMR spectroscopy of the structures of the series of homologous C(80) tetraacids containing 4-8 five-membered rings. In addition, the structures of methyl-substituted C(81) and C(82) analogues containing 7 and 8 five-membered rings have been determined for the first time. The biosynthetic implications are discussed.

  17. Water issues associated with heavy oil production.

    Energy Technology Data Exchange (ETDEWEB)

    Veil, J. A.; Quinn, J. J.; Environmental Science Division

    2008-11-28

    Crude oil occurs in many different forms throughout the world. An important characteristic of crude oil that affects the ease with which it can be produced is its density and viscosity. Lighter crude oil typically can be produced more easily and at lower cost than heavier crude oil. Historically, much of the nation's oil supply came from domestic or international light or medium crude oil sources. California's extensive heavy oil production for more than a century is a notable exception. Oil and gas companies are actively looking toward heavier crude oil sources to help meet demands and to take advantage of large heavy oil reserves located in North and South America. Heavy oil includes very viscous oil resources like those found in some fields in California and Venezuela, oil shale, and tar sands (called oil sands in Canada). These are described in more detail in the next chapter. Water is integrally associated with conventional oil production. Produced water is the largest byproduct associated with oil production. The cost of managing large volumes of produced water is an important component of the overall cost of producing oil. Most mature oil fields rely on injected water to maintain formation pressure during production. The processes involved with heavy oil production often require external water supplies for steam generation, washing, and other steps. While some heavy oil processes generate produced water, others generate different types of industrial wastewater. Management and disposition of the wastewater presents challenges and costs for the operators. This report describes water requirements relating to heavy oil production and potential sources for that water. The report also describes how water is used and the resulting water quality impacts associated with heavy oil production.

  18. Oil Products Quality Improvement by Adsorption Method

    Directory of Open Access Journals (Sweden)

    Kulash K. Syrmanova

    2017-02-01

    Full Text Available Petroleum takes the leading place in fuel and energy sector. It is a basis of fuel and energy balance of advanced countries economics. Light oil proven reserves reducing is a general trend of modern oil industry development. Almost the entire increase in reserves is due to viscous heavy sour oil [1-2]. Nowadays quality of the most important oil products is a crucial problem in refinery industry. The problem of oil products quality is connected with their using and operation in engines and machines. Requirements increasing to stability and effective technics maintenance leads to oil products running abilities significant hardening. In order to protect the environment, the task to obtain oil products with improved environmental properties was assigned. Properties of the oil determine the direction and condition of its processing and directly affect the quality of the oil products [3-4].

  19. Structuring oil by protein building blocks

    NARCIS (Netherlands)

    Vries, de Auke

    2017-01-01

    Over the recent years, structuring of oil into ‘organogels’ or ‘oleogels’ has gained much attention amongst colloid-, material,- and food scientists. Potentially, these oleogels could be used as an alternative for saturated- and trans fats in food products. To develop oleogel

  20. State and trends of oil crops production in China

    Directory of Open Access Journals (Sweden)

    Yang Tiankui

    2016-11-01

    Full Text Available This paper attempts to present a full picture of current situation and future trends of Chinese oil crop production. The total oil crop production remained broadly constant during 2011–2014. The top three oil crops are soybean, peanut and rapeseed, together accounting for more than 70% of total oil crop production. The area under cultivation and the production of peanuts will keep steadily increasing because most Chinese like its pleasant roasted flavor. Because of their high content in polyunsaturated fatty acids and the natural minor functional components in their oils, more attention is being paid to sunflower seed and rice bran. The diminishing availability of arable land and concern over the security of edible oil supplies is driving both a change in cultivation structure of crops and improvements in the efficiency of oilseed production in China.

  1. Prokaryotic community structure and activity of sulfate reducers in production water from high-temperature oil reservoirs with and without nitrate treatment

    DEFF Research Database (Denmark)

    Gittel, Antje; Sørensen, Ketil; Skovhus, Torben L.

    2009-01-01

    Sulfate-reducing prokaryotes (SRP) cause severe problems like microbial corrosion and reservoir souring in seawater-injected oil production systems. One strategy to control SRP activity is the addition of nitrate to the injection water. Production waters from two adjacent, hot (80°C) oil reservoirs......, one with and one without nitrate treatment, were compared for prokaryotic community structure and activity of SRP. Bacterial and archaeal 16S rRNA gene analyses revealed higher prokaryotic abundance but lower diversity for the nitrate-treated field. The 16S rRNA gene clone libraries from both fields...... abundance of archaeal SRP, no archaeal SRP activity was detected in [35S]sulfate incubations at 80°C. Sulfate reduction was found at 60°C in samples from the untreated field and accompanied by the growth of thermophilic bacterial SRP in batch cultures. Samples from the nitrate-treated field generally lacked...

  2. CNPC Refreshes Oil and Gas Production Records

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ Continuous growth in oil and gas production China National Petroleum Corporation (CNPC) hit a record high for oil production again in 2006 by producing 106.64 million tons of oil, 58 percent of the nation's total,and 44.2 billion cubic meters of natural gas, 76 percent of the total.

  3. China Onshore Oil Production Increasing Steadily

    Institute of Scientific and Technical Information of China (English)

    Tian Xueyi

    1995-01-01

    @@ China onshore oil industry made a considerable achievement in 1994 on the basis of developing successively for many years and oil and gas production increasing year after year. Annual crude production reached 139.44 million tons. In the first half of last year, imported crude and finished product has been out of control and oil product has been unsalable so that some oil wells have to be closed and off production in Xinjiang and Daqing. Crude production reduced by 1.28 million tons in total.

  4. Oil Reservoir Production Optimization using Single Shooting and ESDIRK Methods

    DEFF Research Database (Denmark)

    Capolei, Andrea; Völcker, Carsten; Frydendall, Jan;

    2012-01-01

    Conventional recovery techniques enable recovery of 10-50% of the oil in an oil field. Advances in smart well technology and enhanced oil recovery techniques enable significant larger recovery. To realize this potential, feedback model-based optimal control technologies are needed to manipulate...... the injections and oil production such that flow is uniform in a given geological structure. Even in the case of conventional water flooding, feedback based optimal control technologies may enable higher oil recovery than with conventional operational strategies. The optimal control problems that must be solved...... for sensitivity computation. We demonstrate the procedure on a water ooding example with conventional injectors and producers....

  5. Aviation fuel and future oil production scenarios

    OpenAIRE

    2009-01-01

    Most aviation fuels are jet fuels originating from crude oil. Crude oil must be refined to be useful and jet fuel is only one of many products that can be derived from crude oil. Jet fuel is extracted from the middle distillates fraction and competes, for example, with the production of diesel. Crude oil is a limited natural resource subject to depletion and several reports indicate that the world's crude oil production is close to the maximum level and that it will start to decrease after re...

  6. Study of Reservoir Heterogencities and Structural Features Affecting Production in the Shallow Oil Zone, Eastern Elk Hills Area, California

    Energy Technology Data Exchange (ETDEWEB)

    Janice Gillespie

    2004-11-01

    Late Neogene (Plio-Pleistocene) shallow marine strata of the western Bakersfield Arch and Elk Hills produce hydrocarbons from several different reservoirs. This project focuses on the shallow marine deposits of the Gusher and Calitroleum reservoirs in the Lower Shallow Oil Zone (LSOZ). In the eastern part of the study area on the Bakersfield Arch at North and South Coles Levee field and in two wells in easternmost Elk Hills, the LSOZ reservoirs produce dry (predominantly methane) gas. In structurally higher locations in western Elk Hills, the LSOZ produces oil and associated gas. Gas analyses show that gas from the eastern LSOZ is bacterial and formed in place in the reservoirs, whereas gas associated with oil in the western part of the study area is thermogenic and migrated into the sands from deeper in the basin. Regional mapping shows that the gas-bearing LSOZ sands in the Coles Levee and easternmost Elk Hills area are sourced from the Sierra Nevada to the east whereas the oil-bearing sands in western Elk Hills appear to be sourced from the west. The eastern Elk Hills area occupied the basin depocenter, farthest from either source area. As a result, it collected mainly low-permeability offshore shale deposits. This sand-poor depocenter provides an effective barrier to the updip migration of gases from east to west. The role of small, listric normal faults as migration barriers is more ambiguous. Because our gas analyses show that the gas in the eastern LSOZ reservoirs is bacterial, it likely formed in-place near the reservoirs and did not have to migrate far. Therefore, the gas could have been generated after faulting and accumulated within the fault blocks as localized pools. However, bacterial gas is present in both the eastern AND western parts of Elk Hills in the Dry Gas Zone (DGZ) near the top of the stratigraphic section even though the measured fault displacement is greatest in this zone. Bacterial gas is not present in the west in the deeper LSOZ which

  7. Problems Associated with Declining National Oil Production

    Science.gov (United States)

    Jackson, J. S.

    2009-12-01

    Forecasts of peak oil production have focussed on the global impacts of declining production. Meanwhile, national oil production has declined in 20 countries, leading to local problems that receive little comment outside of the effected regions. Two problems deserve wider recognition: declining state revenues and fuel substitution. Most oil producing countries with large reserves adopted licensing practices that provide significant revenues to the host governments such that oil revenues generate from 40 to 80 percent of total government funds. Typically these governments allocate a fraction of this revenue to their state oil companies, utilizing the remainder for other activities. As oil revenues decline with falling production, host governments face a dilemma: either to increase state oil company budgets in order to stem the decline, or to starve the state oil company while maintaining other government programs. The declining oil revenues in these states can significantly reduce the government's ability to address important national issues. Mexico, Indonesia, and Yemen illustrate this situation in its early phases. Fuel substitution occurs whenever one fuel proves less expensive than another. The substitution of coal for wood in the eighteenth century and oil for coal in the twentieth century are classic examples. China and India appear to be at peak oil production, while their economies generate increasing demand for energy. Both countries are substituting coal and natural gas for oil with attendant environmental impacts. Coal-to-liquids projects are proposed in in both China, which will require significant water resources if they are executed. These examples suggest that forecasting the impact of peak oil at a regional level requires more than an assessment of proven-probable-possible reserves and a forecast of supply-demand scenarios. A range of government responses to declining oil income scenarios must also be considered, together with scenarios describing

  8. Accounting for the waterless period of oil production in calculations on oil field production design

    Energy Technology Data Exchange (ETDEWEB)

    Aminov, M.F.; Butorin, O.I.

    1981-01-01

    Formulae on the dynamics of oil and liquid from a methodology developed by the Tatar Scientific-Research and Design Institute for the Oil Industry are adjusted, accounting for the waterless period in oil production. It is demonstrated that the process of accounting for the waterless period in oil production leads to a more accurate prediction of the engineering parameters for mining and oil field.

  9. Structural re-arrangement of depolymerized sodium alginate enriches peltate glandular trichomes and essential oil production of spearmint.

    Science.gov (United States)

    Sadiq, Yawar; Khan, M Masroor A; Shabbir, Asfia; Ahmad, Bilal; Jaleel, Hassan; Uddin, Moin; Varshney, Lalit

    2017-07-25

    Over the past decade, radiation-degraded polysaccharides have been used as regulators of growth and development in several crop plants. In quest of the possible reasons of previously established growth-promotion activity of irradiated sodium alginate (ISA), structural parameters of irradiated and un-irradiated sodium alginate were analysed using Ultraviolet-visible spectroscopy (UV-vis) and Fourier Transform Infrared spectroscopic (FT-IR) studies to develop an understanding of structure-property relationship. Using foliar application, response to graded concentrations of ISA was tested in terms of yield and quality attributes of spearmint (Mentha spicata L.). Among different concentrations of ISA [0 (control), 40, 80, 120 and 160mgL(-1)], 80mgL(-1) proved to be the optimum foliar-spray treatment for most of the parameters studied including peltate glandular-trichomes density, which was increased from 20 to 44mm(-2). Measurements made at 150days after planting revealed that foliar application of ISA at 80mgL(-1) increased the content and yield of spearmint essential oil (EO) by 36.0 and 122.6%, respectively, in comparison to the control. Compared to the control, gas chromatography mass spectrometry (GC-MS) analysis revealed an increase of 18.7% in the carvone content and a decrease of 15.7% in limonene content of the spearmint EO. Copyright © 2017 Elsevier B.V. All rights reserved.

  10. Asphaltene precipitates in oil production wells

    DEFF Research Database (Denmark)

    Kleinitz, W,; Andersen, Simon Ivar

    1998-01-01

    At the beginning of production in a southern German oil field, flow blockage was observed during file initial stage of production from the oil wells. The hindrance was caused by the precipitation of asphaltenes in the proximity of the borehole and in the tubings. The precipitates were of solid...

  11. Transgenic oil palm: production and projection.

    Science.gov (United States)

    Parveez, G K; Masri, M M; Zainal, A; Majid, N A; Yunus, A M; Fadilah, H H; Rasid, O; Cheah, S C

    2000-12-01

    Oil palm is an important economic crop for Malaysia. Genetic engineering could be applied to produce transgenic oil palms with high value-added fatty acids and novel products to ensure the sustainability of the palm oil industry. Establishment of a reliable transformation and regeneration system is essential for genetic engineering. Biolistic was initially chosen as the method for oil palm transformation as it has been the most successful method for monocotyledons to date. Optimization of physical and biological parameters, including testing of promoters and selective agents, was carried out as a prerequisite for stable transformation. This has resulted in the successful transfer of reporter genes into oil palm and the regeneration of transgenic oil palm, thus making it possible to improve the oil palm through genetic engineering. Besides application of the Biolistics method, studies on transformation mediated by Agrobacterium and utilization of the green fluorescent protein gene as a selectable marker gene have been initiated. Upon the development of a reliable transformation system, a number of useful targets are being projected for oil palm improvement. Among these targets are high-oleate and high-stearate oils, and the production of industrial feedstock such as biodegradable plastics. The efforts in oil palm genetic engineering are thus not targeted as commodity palm oil. Due to the long life cycle of the palm and the time taken to regenerate plants in tissue culture, it is envisaged that commercial planting of transgenic palms will not occur any earlier than the year 2020.

  12. Perspectives of microbial oils for biodiesel production.

    Science.gov (United States)

    Li, Qiang; Du, Wei; Liu, Dehua

    2008-10-01

    Biodiesel has become more attractive recently because of its environmental benefits, and the fact that it is made from renewable resources. Generally speaking, biodiesel is prepared through transesterification of vegetable oils or animal fats with short chain alcohols. However, the lack of oil feedstocks limits the large-scale development of biodiesel to some extent. Recently, much attention has been paid to the development of microbial, oils and it has been found that many microorganisms, such as algae, yeast, bacteria, and fungi, have the ability to accumulate oils under some special cultivation conditions. Compared to other plant oils, microbial oils have many advantages, such as short life cycle, less labor required, less affection by venue, season and climate, and easier to scale up. With the rapid expansion of biodiesel, microbial oils might become one of potential oil feedstocks for biodiesel production in the future, though there are many works associated with microorganisms producing oils need to be carried out further. This review is covering the related research about different oleaginous microorganisms producing oils, and the prospects of such microbial oils used for biodiesel production are also discussed.

  13. Crude oil production prospects for continental Europe

    Energy Technology Data Exchange (ETDEWEB)

    Appleby, P. [British Petroleum Co. Ltd., London (United Kingdom)

    1996-10-01

    A medium term view of the prospects for oil production in continental Europe, focusing on the offshore production in UK and Norwegian waters, is presented. The paper begins with a recent history and an overview of current oil production and recent trends. The growth of North Sea production has been important, contributing more than two-thirds of the growth in non OPEC oil production. The development of the Andrew field in the UK North Sea is presented as an example of new management methods succeeding in enhancing the economic viability of oil fields that would otherwise be marginal or non economic The Foinaven field in the new West of Shetlands province illustrates the way in which the combination of technological advances and changes in industry practices is extending the frontiers of commercial viability. Supply projections show North Sea production continuing to grow, but not as rapidly as over the past five years. (author). 7 figs., 8 refs.

  14. Oil production in the Orinoco basin

    Energy Technology Data Exchange (ETDEWEB)

    Borregales, C.J.

    1980-02-01

    With an extension of 42,000 sq km, the Orinoco basin is one of the largest petroliferous zones in the world which contains high viscosity and low API gravity crude. Results from production tests performed in the central and southern parts of the basin indicate that its productive potential is similar to that in Morichal, Pilon and Jobo fields, and reveals that the heaviest oil existing in the Orinoco basin could be economically exploited by conventional methods of primary oil recovery. It is estimated that the oil recovery could be 5% of the total oil-in-place by using primary recovery methods, 8% by using alternate steam injection, and 20% by secondary recovery methods (continuous steam injection). However, if the compaction phenomenon takes place, an estimate of 5% to 15% additional oil recovery could be possible. Geology, fluid properties, results from production tests, and recovery methods in the Orinoco basin are presented.

  15. Considering Oil Production Variance as an Indicator of Peak Production

    Science.gov (United States)

    2010-06-07

    geophysicist Dr. M. King Hubbert mathematically calculated that the United States would reach its maximum crude oil production capacity in 1970. His...Jean Laherrere) have presented data that indicate all nations together will reach collective maximum crude oil production capacity between 2004 and

  16. Impacts from Partial Removal of Decommissioned Oil and Gas Platforms on Fish Biomass and Production on the Remaining Platform Structure and Surrounding Shell Mounds.

    Directory of Open Access Journals (Sweden)

    Jeremy T Claisse

    Full Text Available When oil and gas platforms become obsolete they go through a decommissioning process. This may include partial removal (from the surface to 26 m depth or complete removal of the platform structure. While complete removal would likely eliminate most of the existing fish biomass and associated secondary production, we find that the potential impacts of partial removal would likely be limited on all but one platform off the coast of California. On average 80% of fish biomass and 86% of secondary fish production would be retained after partial removal, with above 90% retention expected for both metrics on many platforms. Partial removal would likely result in the loss of fish biomass and production for species typically found residing in the shallow portions of the platform structure. However, these fishes generally represent a small proportion of the fishes associated with these platforms. More characteristic of platform fauna are the primarily deeper-dwelling rockfishes (genus Sebastes. "Shell mounds" are biogenic reefs that surround some of these platforms resulting from an accumulation of mollusk shells that have fallen from the shallow areas of the platforms mostly above the depth of partial removal. We found that shell mounds are moderately productive fish habitats, similar to or greater than natural rocky reefs in the region at comparable depths. The complexity and areal extent of these biogenic habitats, and the associated fish biomass and production, will likely be reduced after either partial or complete platform removal. Habitat augmentation by placing the partially removed platform superstructure or some other additional habitat enrichment material (e.g., rock boulders on the seafloor adjacent to the base of partially removed platforms provides additional options to enhance fish production, potentially mitigating reductions in shell mound habitat.

  17. PRODUCTION OF HIGH QUALITY LUBRICATING BASE OIL

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    @@High VI lubricating oil is produced in hydrocracker through hydrocracking (HDC) and hydroisome-rization reactions. In order to effectively produce high VI component, such as iso-pafaffins and monocyclic naphtenes, it is important to load suitable HDC catalysts and operate them in the appropriate reaction conditions.   Nippon Mitsubishi Oil Corporation (NMOC) and its affiliate company, Nippon Mitsubishi Petroleum Refining Company (NMPRC) reported their original HDC catalysts four years ago in this Japan-China joint se-minar in Beijing[1]. NMOC and NMPRC operate their hydrocracker both in fuel oil production mode and in lubricating oil production mode. In lubricating oil production mode, high VI lubricating oil called VHDC are produced.   In this paper, at first, the advantages of high VI lubricating oil are described. And then it is announced that NMOC and NMPRC have developed a new generation of HDC catalyst with higher cracking activity, higher middle distillate selectivity and longer life than the other commercial HDC catalysts. In addition to those properties, the catalyst is able to yield high VI lubricating oil as well.

  18. Retail Market of Oil Products Reshuffled Soon

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ According to its commitments to the World Trade Organization, the Chinese government opened up China's oil products retail market fully on December 11, 2004. Centering on this important transition, a market pattern of multi-major-body will be appeared.

  19. 17 CFR 229.1204 - (Item 1204) Oil and gas production, production prices and production costs.

    Science.gov (United States)

    2010-04-01

    ... price (including transfers) per unit of oil, gas and other products produced; and (2) The average... conversion to synthetic oil or gas, the product's production, transfer prices, and production costs should be disclosed separately from all other products. Instruction 4 to Item 1204: The transfer price of oil and...

  20. Studies on water-in-oil products from crude oils and petroleum products.

    Science.gov (United States)

    Fingas, Merv; Fieldhouse, Ben

    2012-02-01

    Water-in-oil mixtures such as emulsions, often form and complicate oil spill countermeasures. The formation of water-in-oil mixtures was studied using more than 300 crude oils and petroleum products. Water-in-oil types were characterized by resolution of water at 1 and 7 days, and some after 1 year. Rheology measurements were carried out at the same intervals. The objective of this laboratory study was to characterize the formed water-in-oil products and relate these properties to starting oil properties. Analysis of the starting oil properties of these water-in-oil types shows that the existence of each type relates to the starting oil viscosity and its asphaltene and resin contents. This confirms that water-in-oil emulsification is a result of physical stabilization by oil viscosity and chemical stabilization by asphaltenes and resins. This stabilization is illustrated using simple graphical techniques. Four water-in-oil types exist: stable, unstable, meso-stable and entrained. Each of these has distinct physical properties. Copyright © 2011 Elsevier Ltd. All rights reserved.

  1. OIL EXPLORATION AND PRODUCTION IN CROATIA

    Directory of Open Access Journals (Sweden)

    Josip Sečen

    1996-12-01

    Full Text Available Organized exploration of "earth oil" shows started in the 16th century, and the oil production in the middle of the 20th century. The exploration area of the Republic of Croatia is divided into three basins: Pannonian, Dinarides and Adriatic. The most explored is the Panonian Basin, where most oil and gas reserves have been discovered that are continuously being produced. In the Adriatic basin gas reserves have heen discovered but because of the commercial reasons they haven't been used yet. Along with the exploration at home, the perspective areas in foreign contries are being explored more and more with the considerable oil and gas reserves discoveries. Two main products, oil and gas, generate the production of other fuels and raw materials necessary in petrochemical industry: propane, butane, industrial spirit, ethylene, propylene etc. The major part of those products is directly included into the power-supply programme of the Republic of Croatia and they supply 45% of total power needs. Good results in exploration and a high participation of domestic oil and gas in total primary energy supply, direct to the further intense investments in explorations of domestic and perspective foreign areas (the paper is published in Croatian.

  2. Global Trends and Development Prospects for Oil and the Oil Products Market

    Directory of Open Access Journals (Sweden)

    Maria Dorozhkina

    2006-03-01

    Full Text Available This article discusses the important issue of the development of the global market of oil and oil products. It offers an overview of how this market was formed and its current status, classification, location and potential of countries in the oil and oil processing business. It analyzes the Ukrainian oil products market. The article discusses the shortcomings and strategic areas for the development of Ukraine’s oil transport system. It presents an optimum method for creating integration groups in order to develop the oil processing business in Ukraine for the future. The article considers the main trends and outlines development prospects for the global oil and oil products market.

  3. China Onshore Oil and Gas Production in 1995

    Institute of Scientific and Technical Information of China (English)

    Yue Dengtai

    1996-01-01

    @@ Oil and Gas Production in 1995 In 1995, while the production in some of the old eastern oil fields was decreased, the production of the eastern oil and gas fields as a whole was further raised by taking such measures as laying emphasis on productivity construction of new oil blocks, continuously adjusting and developing the potential of old oil fields and fully adopting various effective methods.

  4. Production, properties and utilisation of pyrolysis oil

    Energy Technology Data Exchange (ETDEWEB)

    Sipilae, K.; Oasmaa, A.; Arpiainen, V.; Solantausta, Y.; Leppaemaeki, E.; Kuoppala, E.; Levander, J.; Kleemola, J.; Saarimaeki, P. [VTT Energy, Jyvaeskylae (Finland). Energy Production Technologies

    1997-12-01

    In this project VTT Energy co-ordinates the EU JOULE Project `Biofuel oil for power plants and boilers` supporting the development projects of Finnish enterprises, and participates in the Pyrolysis Project of IEA Bioenergy Agreement. Presently two pyrolysis devices with capacities of 150 g/h and 1 kg/h are used for the project. Hot gas filtering tests by using one ceramic candle equipment have been carried out with the 1 kg/h device for pyrolysis oil. The solids and alkali contents of the product oil were reduced clearly. Suitable conditions are being defined for continuous hot gas filtering. A PDU device of 20 kg/h is being commissioned. The main aim of the chemical characterisation of pyrolysis oil was to develop as simple a method as possible for differentiating pyrolysis oils and for finding correlations between the characteristics and behaviour of pyrolysis oils. Pyrolysis oils produced from various raw materials (hardwood, pine, straw) were analysed and compared with each other. VTT Energy participates in the pyrolysis network (EU/PYNE) of EU, the aim of which is to collect and disseminate research results of pyrolysis studies, i.e., through a journal with a wide circulation. VTT also participates in the pyrolysis activity of IEA (PYRA), the other partners being Great Britain, EU, Canada and the United States. I.e., quality criteria and improvement, occupational safety and pyrolysis kinetics are discussed in IEA/PYRA

  5. Production of Biodiesel from Chicken Frying Oil

    Directory of Open Access Journals (Sweden)

    Emaad T. Bakir

    2011-12-01

    Full Text Available Chicken fried oil was converted into different biodiesels through single step transesterification and two step transesterification, namely acid-base and base–base catalyzed transesterification. Hydrochloric acid and potassium hydroxide with methanol were used for this purpose. The results showed that two step base catalyzed transesterification was better compared to other methods. It resulted in higher yield and better fuel properties. Transesterification of fried chicken oil was monitored by TLC technique and compared with that of the parent oil. Fuel properties of the products have been measured and found markedly enhanced compared to those of the parent oil. Also, the values satisfied the standard limits according to the ASTM standards. Blending of the better biodiesel sample with petro diesel was made using three volume percentages (10, 30 and 50% v/v. The results disclosed that blending had slight effect on the original properties of petro diesel.

  6. HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS

    Energy Technology Data Exchange (ETDEWEB)

    Anthony R. Kovscek

    2003-01-01

    This technical progress report describes work performed from October 1 through December 31, 2002 , for the project ''Heavy and Thermal Oil Recovery Production Mechanisms.'' In this project, a broad spectrum of research is undertaken related to thermal and heavy-oil recovery. The research tools and techniques used are varied and span from pore-level imaging of multiphase fluid flow to definition of reservoir-scale features through streamline-based history-matching techniques. During this period, experimental data regarding multidimensional imbibition was analyzed to obtain shape factors appropriate for dual-porosity simulation. It is shown that the usual assumption of constant, time-independent shape factors is incorrect. In other work, we continued to study the mechanisms by which oil is produced from fractured media at high pressure and high temperature. High temperature significantly increased the apparent wettability and affected water relative permeability of cores used in previous experiments. A phenomenological and mechanistic cause for this behavior is sought. Our work in the area of primary production of heavy oil continues with field cores and crude oil. On the topic of reservoir definition, work continued on developing techniques that integrate production history into reservoir models using streamline-based properties.

  7. Biodiesel production from Jatropha curcas oil

    Energy Technology Data Exchange (ETDEWEB)

    Jain, Siddharth; Sharma, M.P. [Alternate Hydro Energy Centre, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667 (India)

    2010-12-15

    In view of the fast depletion of fossil fuel, the search for alternative fuels has become inevitable, looking at huge demand of diesel for transportation sector, captive power generation and agricultural sector, the biodiesel is being viewed a substitute of diesel. The vegetable oils, fats, grease are the source of feedstocks for the production of biodiesel. Significant work has been reported on the kinetics of transesterification of edible vegetable oils but little work is reported on non-edible oils. Out of various non-edible oil resources, Jatropha curcas oil (JCO) is considered as future feedstocks for biodiesel production in India and limited work is reported on the kinetics of transesterification of high FFA containing oil. The present study reports a review of kinetics of biodiesel production. The paper also reveals the results of kinetics study of two-step acid-base catalyzed transesterification process carried out at pre-determined optimum temperature of 65 and 50 C for esterification and transesterification process, respectively, under the optimum condition of methanol to oil ratio of 3:7 (v/v), catalyst concentration 1% (w/w) for H{sub 2}SO{sub 4} and NaOH and 400 rpm of stirring. The yield of methyl ester (ME) has been used to study the effect of different parameters. The maximum yield of 21.2% of ME during esterification and 90.1% from transesterification of pretreated JCO has been obtained. This is the first study of its kind dealing with simplified kinetics of two-step acid-base catalyzed transesterification process carried at optimum temperature of both the steps which took about 6 h for complete conversion of TG to ME. (author)

  8. Production Optimization of Oil Reservoirs

    DEFF Research Database (Denmark)

    Völcker, Carsten

    with emphasis on optimal control of water ooding with the use of smartwell technology. We have implemented immiscible ow of water and oil in isothermal reservoirs with isotropic heterogenous permeability elds. We use the method of lines for solution of the partial differential equation (PDE) system that governs...... the uid ow. We discretize the the two-phase ow model spatially using the nite volume method (FVM), and we use the two point ux approximation (TPFA) and the single-point upstream (SPU) scheme for computing the uxes. We propose a new formulation of the differential equation system that arise...... as a consequence of the spatial discretization of the two-phase ow model. Upon discretization in time, the proposed equation system ensures the mass conserving property of the two-phase ow model. For the solution of the spatially discretized two-phase ow model, we develop mass conserving explicit singly diagonally...

  9. Product Structuring, an overview

    DEFF Research Database (Denmark)

    Tichem, Marcel; Storm, Ton; Andreasen, Mogens Myrup;

    1997-01-01

    This paper presents the highlights of two WDK Workshops on Product Structuring. Product structuring plays an important role in creating products which have good functional and life-cycle related properties, in design process management, and in several other company functions like production control...

  10. Collaborative production management for oil sands operations

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Andrew [Matrikon (Canada)

    2011-07-01

    This paper gives an overview of the collaborative production management of oil sands operations. Some characteristics of oil sands operations include oil treatment, hydro treating, diluent addition, logistics, and environmental impact assessments. Some of the business challenges include regulatory uncertainty, a fluid workforce and a technology still in the process of being developed. Improvement is only possible when process is assessed and measured; hence, production data management is very important. Production data measurements encompass such areas as planning, documentation and transactions. Regulatory data reporting is represented using a flow chart. The concepts of business application architecture and functional reference modeling are also explained. Benchmarking plays a vital role, some aspects of which would be technology, automation and integration. Certain advantages of timely assessment are increased production, equity, and goodwill as well as reduction in costs, risk, and capital requirements. The relevance and importance of collaboration, awareness of web technology and aggregate information are also explained. From the study, it can be concluded that the key to overall improvement in the oil sands industry will be improved production management.

  11. Marine Lipids (Omega-3 Oil) - Stability of Oil and Enriched Products During Production and Storage

    DEFF Research Database (Denmark)

    Nielsen, Nina Skall

    2015-01-01

    The awareness of health benefits of marine lipids with a high content of omega-3 poly unsaturated fatty acids from fish and algae oil has led to an increased intake as oil and in products. However, these lipids are highly susceptible to lipid oxidation, which results in the formation of undesirab...

  12. Sustainability aspects of biobased products : comparison of different crops and products from the vegetable oil platform

    NARCIS (Netherlands)

    Meesters, K.P.H.; Corré, W.J.; Conijn, J.G.; Patel, M.K.; Bos, H.L.

    2012-01-01

    This study focusses on the production of vegetable oil based products. A limited number of aspacts of the sustainability of the full chain (from agriculture to product at the factory gate) was evaluated. Three different vegetable oils were taken into account: palm oil, soy oil and rapeseed oil. Also

  13. Production of fats and oils by microorganisms

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Osamu

    1987-10-20

    This paper describes the production of fats and oils by microorganisms. Various fat-productive bacteria have been found to produce the fats and oils by microorganisms which are roughly classified into enzyme and filiform fungus. The cells do not proliferate under the conditions adequate for producing the cells with the high content of lipid. A cell with high content of fat belonging to Mortierella filamentas fungi has been recently obtained at high density in the high concentration culture medium. The productivity of the fat similar to cocoa butter seems to be also high. A lot of microorganisms producing various functional fatty acids have been found. The microorganismic production methods of esters of longer-chain dicarboxylic acids and alcohols than C/sub 11/ hardly produced in nature form n-alkane also have been recently developed. Squalene has been able to produce by a cell from the other raw materials than the shark oil. Various sterols exist in microorganisms. The high-productivity manufacturing method of the fats containing gamma-linoleic acid by Mortierella filiform fungi has been developed and commercialized as the first production process of the fat by the microorganism. (5 figs, 7 tabs, 128 refs

  14. CNOOC Ltd Sets 2006 Oil Production Targets

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    @@ China National Offshore Oil Company Limited (CNOOC Ltd) is expected to bring up its total budgeted net output in 2006 to a new record high to hit between 168 million and 170 million barrels of oil equivalent (BOE).The budget volume is approximately a nine percent year-on-year increase over the estimated 153 million to 157million BOE in 2005. The net production volume of CNOOC Ltd in the domestic offshore area is estimated to be 148 million to 149 million BOE in 2006.

  15. PRODUCT STRUCTURE DIGITAL MODEL

    Directory of Open Access Journals (Sweden)

    V.M. Sineglazov

    2005-02-01

    Full Text Available  Research results of representation of product structure made by means of CADDS5 computer-aided design (CAD system, Product Data Management Optegra (PDM system and Product Life Cycle Management Wind-chill system (PLM, are examined in this work. Analysis of structure component development and its storage in various systems is carried out. Algorithms of structure transformation required for correct representation of the structure are considered. Management analysis of electronic mockup presentation of the product structure is carried out for Windchill system.

  16. Oil Reservoir Production Optimization using Optimal Control

    DEFF Research Database (Denmark)

    Völcker, Carsten; Jørgensen, John Bagterp; Stenby, Erling Halfdan

    2011-01-01

    Practical oil reservoir management involves solution of large-scale constrained optimal control problems. In this paper we present a numerical method for solution of large-scale constrained optimal control problems. The method is a single-shooting method that computes the gradients using the adjo......Practical oil reservoir management involves solution of large-scale constrained optimal control problems. In this paper we present a numerical method for solution of large-scale constrained optimal control problems. The method is a single-shooting method that computes the gradients using...... the adjoint method. We use an Explicit Singly Diagonally Implicit Runge-Kutta (ESDIRK) method for the integration and a quasi-Newton Sequential Quadratic Programming (SQP) algorithm for the constrained optimization. We use this algorithm in a numerical case study to optimize the production of oil from an oil...... reservoir using water ooding and smart well technology. Compared to the uncontrolled case, the optimal operation increases the Net Present Value of the oil field by 10%....

  17. Non-Linear Unit Root Properties of Crude Oil Production

    OpenAIRE

    Svetlana Maslyuk; Russell Smyth

    2007-01-01

    While there is good reason to expect crude oil production to be non-linear, previous studies that have examined the stochastic properties of crude oil production have assumed that crude oil production follows a linear process. If crude oil production is a non-linear process, conventional unit root tests, which assume linear and systematic adjustment, could interpret departure from linearity as permanent stochastic disturbances. The objective of this paper is to test for non-linearities and un...

  18. Production of polyhydroxyalkanoates from waste frying oil by Cupriavidus necator

    Science.gov (United States)

    2011-01-01

    Polyhydroxyalkanoates (PHAs) are biopolymers, which can replace petrochemical plastics in many applications. However, these bioplastics are currently far more expensive than petrochemical plastics. Many researchers are investigating the use of inexpensive substrates derived from waste streams. Waste frying oil is abundant and can be used in PHA production without filtration. Cupriavidus necator (formerly known as Ralstonia eutropha) is a versatile organism for the production of PHAs. Small-scale batch fermentation studies have been set up, using different concentrations of pure vegetable oil, heated vegetable oil and waste frying oil. These oils are all rapeseed oils. It has been shown that Cupriavidus necator produced the homopolymer polyhydroxybutyrate (PHB) from the rapeseed oils. The achieved PHB concentration from waste frying oil was 1.2 g/l, which is similar to a concentration that can be obtained from glucose. The PHB harvest from pure oil and heated oil was 0.62 g/l and 0.9 g/l respectively. A feed of waste frying oil could thus achieve more biopolymer than pure vegetable oil. While the use of a waste product is beneficial from a life-cycle perspective, PHB is not the only product that can be made from waste oil. The collection of waste frying oil is becoming more widespread, making waste oil a good alternative to purified oil or glucose for PHB production. PMID:21906352

  19. Edible oil structuring: an overview and recent updates.

    Science.gov (United States)

    Patel, Ashok R; Dewettinck, Koen

    2016-01-01

    In recent years, research dealing with edible oil structuring has received considerable interest from scientific community working in the area of food formulation. Much of this interest is linked to the possibility of using structured oil in development of newer product formats with improved nutritional profile (trans fat-free, low in saturated fats and high in mono and/or poly unsaturated fatty acids). In addition to the obvious industrial need of finding the alternative formulation approach, the interesting properties of structured systems (particularly, oleogels) also makes them a fascinating subject for fundamental studies. In this paper, we attempt to give a comprehensive and concise overview of the field of oil structuring with special emphasis on the updates from recent years. Specifically, several categories of food-grade oleogelators and their potential food applications are summarized with typical examples along with a discussion on the general principles and unresolved challenges related to this emerging area.

  20. Bioemulsan Production by Iranian Oil Reservoirs Microorganisms

    Directory of Open Access Journals (Sweden)

    A Amiriyan, M Mazaheri Assadi, VA Saggadian, A Noohi

    2004-10-01

    Full Text Available The biosurfactants are believed to be surface active components that are shed into the surrounding medium during the growth of the microorganisms. The oil degrading microorganism Acinetobacter calcoaceticus RAG-1 produces a poly-anionic biosurfactant, hetero-polysaccharide bioemulsifier termed as emulsan which forms and stabilizes oil-water emulsions with a variety of hydrophobic substrates. In the present paper results of the possibility of biosurfactant (Emulsan production by microorganisms isolated from Iranian oil reservoirs is presented. Fourthy three gram negative and gram positive, non fermentative, rod bacilli and coccobacilli shaped baceria were isolated from the oil wells of Bibi Hakimeh, Siri, Maroon, Ilam , East Paydar and West Paydar. Out of the isolated strains, 39 bacterial strains showed beta haemolytic activity, further screening revealed the emulsifying activity and surface tension. 11 out of 43 tested emulsifiers were identified as possible biosurfactant producers and two isolates produced large surface tension reduction, indicating the high probability of biosurfactant production. Further investigation revealed that, two gram negative, oxidase negative, aerobic and coccoid rods isolates were the best producers and hence designated as IL-1, PAY-4. Whole culture broth of isolates reduced surface tension from 68 mN /m to 30 and 29.1mN/m, respectively, and were stable during exposure to high salinity (10%NaCl and elevated temperatures(120C for 15 min .

  1. Palm olein oil produces less lipid peroxidation products than soya bean oil.

    Science.gov (United States)

    Zaiton, Z; Merican, Z; Khalid, B A; Mohamed, J B; Baharom, S

    1997-06-01

    The soleus muscles of hyperthyroid rats were used to investigate the effect of palm olein oil and soya bean oil on the production of lipid peroxidation products. It was found that palm olein oil but not soya bean oil significantly decreased malonaldehyde and conjugated diene levels of the soleus muscles of hyperthyroid rats. These findings suggest that palm olein per se produces less lipid peroxidation products than soya bean oil. Such an assay method gives a composite net picture of the propensity of an oil to produce lipid peroxidation products.

  2. Effect of cocoa butter structure on oil migration.

    Science.gov (United States)

    Maleky, Fatemeh; McCarthy, Kathryn L; McCarthy, Michael J; Marangoni, Alejandro G

    2012-03-01

    Oil migration from a high oil content filling into adjacent chocolate causes changes in product quality. The objective of this study was to quantify the oil migration from a cream filling system into cocoa butter, which provided a model for the behavior of chocolate-enrobed confectionery products with a soft, creamy center. Magnetic resonance imaging (MRI) was used to monitor spatial and temporal changes of liquid lipid content. A multislice spin echo pulse sequence was used to acquire images with a 7.8 ms echo time and a 200 ms repetition time using a 1.03 T Aspect Imaging MRI spectrometer. Samples were prepared as a 2-layer model system of cocoa butter and model cream filling. Three methods were used to prepare the cocoa butter: static, seeded, and sheared. Samples were stored at 25 °C for a time frame of 56 d. The rate of oil migration was quantified by a kinetic expression based on the linear dependence of oil uptake by cocoa butter and the square root of the time. Samples showed distinctly different rates of oil migration, as evidenced by quantitative differences in the kinetic rate constant. Practical Application:  This work will be helpful to elucidate the influence of crystallization process and structural properties such as crystal nanostructure and crystal habit on the migration of oil through a crystalline fat matrix.

  3. Optimization of Jatropha curcas pure plant oil production

    NARCIS (Netherlands)

    Subroto, Erna

    2015-01-01

    The use of pure plant oils as fuel, either directly or after conversion of the oil to bio-diesel, is considered to be one of the potential contributions to the transformation of the current fossil oil based economy to a sustainable bio-based one. The production of oil producing seeds using plants

  4. Analysis of China's Oil Products Market

    Institute of Scientific and Technical Information of China (English)

    Liang Gang

    2001-01-01

    @@ During the first half of 2001, the Chinese market of oil products suffered from shortage of resources with the prices falling in the first quarter but saw rapid growth in resources with the demand and price rising steadily.However, in June, the market demand growth began to slow down due to the price fall in the world market and the high market price at home. It is forecasted that the Chinese oil products market will have a steady growth in demand with a slowdown in the price rise and will fluctuate with the world market in the later half of this year. The growth rate will be lower than that of last year.

  5. Opportunities in oil sands production bi-products

    Energy Technology Data Exchange (ETDEWEB)

    Gunardson, H. [Air Products Canada Ltd., Calgary, AB (Canada)

    2006-07-01

    This presentation investigated potential by-products from oil sands production and upgrading facilities, and examined the extent to which carbon dioxide (CO{sub 2}) enhanced oil recovery (EOR) projects can absorb greenhouse gas (GHG) emissions from oil sands developments. Oil sands production by-products included bitumen and petroleum coke; heat; hydrocarbon off-gases; hydrogen; syngas; sulfur; metals; and CO{sub 2} sources from combustion processes and hydrogen production. CO{sub 2} concentrations from flue gases are typically less than 17 per cent, and contain contaminants such as nitrogen, particulates, nitrogen oxide (NO{sub x}) and sulphur dioxide (SO{sub x}). CO{sub 2} concentrations derived from hydrogen production have a high purity and contain water vapour, unreacted hydrocarbons, hydrogen sulphide (H{sub 2}S) and volatile metals. Existing carbon capture technologies are currently not capable of processing large volumes of CO{sub 2}. However, small volumes of CO{sub 2} are used in the manufacturing of carbonated beverages. Larger volumes of CO{sub 2} are used in EOR and coalbed methane (CBM) recovery as well as in CO{sub 2} sequestration. Carbon capture technologies include amine scrubbers, selexol and rectisol gasification processes, and Benfield Catacarb processes. The market price for CO{sub 2} in EOR and gas recovery is approximately $35 per tonne. However, combustion processes typically cost $103 per tonne. CO{sub 2} sources and sinks were also identified. It is estimated that total CO{sub 2} sequestration using EOR will equal 200 mega tonnes by 2030. Apart from gasification processes, all CO{sub 2} sources are uneconomic using current technology. The oil sands industry is in need of a policy framework and support for infrastructure investments for CO{sub 2} pipelines and sequestration facilities. tabs., figs.

  6. Production of structured lipids by acidolysis of an EPA-enriched fish oil and caprylic acid in a packed bed reactor: analysis of three different operation modes.

    Science.gov (United States)

    González Moreno, P A; Robles Medina, A; Camacho Rubio, F; Camacho Páez, B; Molina Grima, E

    2004-01-01

    Structured triacylglycerols (ST) enriched in eicosapentaenoic acid (EPA) in position 2 of the triacylglycerol (TAG) backbone were synthesized by acidolysis of a commercially available EPA-rich oil (EPAX4510, 40% EPA) and caprylic acid (CA), catalyzed by the 1,3-specific immobilized lipase Lipozyme IM. The reaction was carried out in a packed bed reactor (PBR) operating in two ways: (1) by recirculating the reaction mixture from the exit of the bed to the substrate reservoir (discontinuous mode) and (2) in continuous mode, directing the product mixture leaving the PBR to a product reservoir. By operating in these two ways and using a simple kinetic model, representative values for the apparent kinetic constants (kX) for each fatty acid (native, Li or odd, M) were obtained. The kinetic model assumes that the rate of incorporation of a fatty acid into TAG per amount of enzyme, rX (mole/(h g lipase)) is proportional to the extent of the deviation from the equilibrium for each fatty acid (i.e., the difference of concentration between the fatty acid in the triacylglycerol and the concentration of the same fatty acid in the triacylglycerol once the equilibrium of the acidolysis reaction is reached). The model allows comparing the two operating modes through the processing intensity, defined as mLt/(V[TG]0) and mL/(q[TG]0), for the discontinuous and continuous operation modes, respectively. In discontinuous mode, ST with 59.5% CA and 9.6% EPA were obtained. In contrast, a ST with 51% CA and 19.6% EPA were obtained when using the continuous operation mode. To enhance the CA incorporation when operating in continuous mode, a two-step acidolysis reaction was performed (third operation mode). This continuous two-step process yields a ST with a 64% CA and a 15% EPA. Finally, after purifying the above ST in a preparative silica gel column, impregnated with boric acid, a ST with 66.9% CA and 19.6% EPA was obtained. The analysis by reverse phase and Ag+ liquid chromatography of

  7. HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS

    Energy Technology Data Exchange (ETDEWEB)

    Anthony R. Kovscek; Louis M. Castanier

    2002-09-30

    The Stanford University Petroleum Research Institute (SUPRI-A) conducts a broad spectrum of research intended to help improve the recovery efficiency from difficult to produce reservoirs including heavy oil and fractured low permeability systems. Our scope of work is relevant across near-, mid-, and long-term time frames. The primary functions of the group are to conduct direction-setting research, transfer research results to industry, and educate and train students for careers in industry. Presently, research in SUPRI-A is divided into 5 main project areas. These projects and their goals include: (1) Multiphase flow and rock properties--to develop better understanding of the physics of displacement in porous media through experiment and theory. This category includes work on imbibition, flow in fractured media, and the effect of temperature on relative permeability and capillary pressure. (2) Hot fluid injection--to improve the application of nonconventional wells for enhanced oil recovery and elucidate the mechanisms of steamdrive in low permeability, fractured porous media. (3) Mechanisms of primary heavy oil recovery--to develop a mechanistic understanding of so-called ''foamy oil'' and its associated physical chemistry. (4) In-situ combustion--to evaluate the effect of different reservoir parameters on the insitu combustion process. (5) Reservoir definition--to develop and improve techniques for evaluating formation properties from production information. What follows is a report on activities for the past year. Significant progress was made in all areas.

  8. Virgin Coconut Oil Production by Centrifugation Method

    OpenAIRE

    2014-01-01

    The virgin coconut oil (VCO) production by centrifugation method was studied. The production of VCO was studied by using various centrifugation speed, temperature and time intervals. The results showed that the yield of VCO was 13.53% at 12000rpm, at 120 minutes. The highest yield of VCO was 13.80% at centrifugation temperature of 40oC. The concentration of lauric acid present in the samples with variables of centrifugation temperatures, speed, and time intervals were 0.4543µg, 6.2367µg, and ...

  9. Virgin Coconut Oil Production by Centrifugation Method

    Directory of Open Access Journals (Sweden)

    Y.C.Wong

    2014-03-01

    Full Text Available The virgin coconut oil (VCO production by centrifugation method was studied. The production of VCO was studied by using various centrifugation speed, temperature and time intervals. The results showed that the yield of VCO was 13.53% at 12000rpm, at 120 minutes. The highest yield of VCO was 13.80% at centrifugation temperature of 40oC. The concentration of lauric acid present in the samples with variables of centrifugation temperatures, speed, and time intervals were 0.4543µg, 6.2367µg, and 6.4894µg respectively.

  10. Potential Development Essential Oil Production of Central Java, Indonesia

    Science.gov (United States)

    Alighiri, D.; Eden, W. T.; Supardi, K. I.; Masturi; Purwinarko, A.

    2017-04-01

    Indonesia is the source of raw essential oil in the world. Essential oils are used in various types of industries such as food and beverage, flavour, fragrance, perfumery, pharmaceuticals, and cosmetics. However, the development of Indonesian essential oil industry has not been encouraging for the production of essential oils, further it is unable to meet global demand. Besides that, the quality of volatile oil resulted cannot meet the international market standards. Based on the facts, the potential of Indonesian essential oils needs to be developed to provide added value, through increased production, improved quality and product diversification. One part of Indonesia having abundant of raw essential oil source is Central Java. Central Java has the quite large potential production of essential oils. Some essential oils produced from refining industry owned by the government, private and community sectors include cananga oils (Boyolali district), clove oils (Semarang district), patchouli oils (Brebes district, Pemalang district, and Klaten district). The main problem in the development of plants industries that producing essential oil in Central Java is low crops production, farming properties, quality of essential oils are diverse, providing poor-quality products and volatile oil price fluctuations. Marketing constraints of Central Java essential oils are quite complex supply chain. In general, marketing constraints of essential oils due to three factors, namely the low quality due to type of essential oil business that generally shaped small businesses with different capital and technology, domestic marketing is still a buyer-market (price determined by the buyer) because of weak bargaining position processors businessman, and prices fluctuate (domestic and foreign) due to uncontrolled domestic production and inter-country competition among manufacturers.

  11. Production of polyol oils from soybean oil by bioprocess and Philippines edible medicinal wild mushrooms

    Science.gov (United States)

    We have been trying to develop a bioprocess for the production of polyol oils directly from soybean oil. We reported earlier the polyol products produced from soybean oil by Acinetobacter haemolyticus A01-35 (NRRL B-59985) (Hou and Lin, 2013). The objective of this study is to identify the chemical ...

  12. Production of polyol oils from soybean oil by Pseudomonas aeruginosa E03-12.

    Science.gov (United States)

    Soy-polyols are important starting materials for the manufacture of polymers such as polyurethane. We have been trying to develop a bioprocess for the production of polyol oils directly from soybean oil. We reported earlier the polyol products produced from soybean oil by Acinetobacter haemolyticus ...

  13. An analysis of oil production by OPEC countries: Persistence, breaks, and outliers

    Energy Technology Data Exchange (ETDEWEB)

    Pestana Barros, Carlos, E-mail: cbarros@iseg.utl.p [Instituto Superior de Economia e Gestao and Research Unit on Complexity and Economics, Technical University of Lisbon, Lisbon (Portugal); Gil-Alana, Luis A., E-mail: alana@unav.e [University of Navarra, Pamplona (Spain); Payne, James E., E-mail: jepayne@ilstu.ed [Department of Economics, Illinois State University, Normal, IL 61790-4200 (United States)

    2011-01-15

    This study examines the time series behaviour of oil production for OPEC member countries within a fractional integration modelling framework recognizing the potential for structural breaks and outliers. The analysis is undertaken using monthly data from January 1973 to October 2008 for 13 OPEC member countries. The results indicate there is mean reverting persistence in oil production with breaks identified in 10 out of the 13 countries examined. Thus, shocks affecting the structure of OPEC oil production will have persistent effects in the long run for all countries, and in some cases the effects are expected to be permanent. - Research Highlights: {yields}Mean reverting persistence in oil production with breaks identified in 10 out of the 13 countries examined. {yields} Standard analysis based on cointegration techniques and involving oil production should be examined in the more general context of fractional cointegraton. {yields} Analysis of outliers did not alter the main conclusions of the study.

  14. Medium and Long Term Crude Oil Price Outlook: Economic research on shale oil and gas production behavior in the United States (Japanese)

    OpenAIRE

    2015-01-01

    It has been pointed out that the steep fall in crude oil prices after the latter half of 2014 has been strongly affected by both demand side factors such as the slowdown of world economic growth and supply side factors such as a massive increase in shale oil production in the United States and other structural factors. Shale oil and gas production is well known for its different aspects compared to conventional oil and gas production such as differences in oil and gas reserves, differences in...

  15. Factors affecting oil palm production in Ondo state of Nigeria

    African Journals Online (AJOL)

    sola

    Regression analysis showed that only two of the variables; level of education ... were predicted to have significant relationship with the yield of oil palm. ..... Table 5: Multiple Regression analysis of factors affecting oil palm production in.

  16. Mitigation of maximum world oil production: Shortage scenarios

    Energy Technology Data Exchange (ETDEWEB)

    Hirsch, Robert L. [Management Information Services, Inc., 723 Fords Landing Way, Alexandria, VA 22314 (United States)

    2008-02-15

    A framework is developed for planning the mitigation of the oil shortages that will be caused by world oil production reaching a maximum and going into decline. To estimate potential economic impacts, a reasonable relationship between percent decline in world oil supply and percent decline in world GDP was determined to be roughly 1:1. As a limiting case for decline rates, giant fields were examined. Actual oil production from Europe and North America indicated significant periods of relatively flat oil production (plateaus). However, before entering its plateau period, North American oil production went through a sharp peak and steep decline. Examination of a number of future world oil production forecasts showed multi-year rollover/roll-down periods, which represent pseudoplateaus. Consideration of resource nationalism posits an Oil Exporter Withholding Scenario, which could potentially overwhelm all other considerations. Three scenarios for mitigation planning resulted from this analysis: (1) A Best Case, where maximum world oil production is followed by a multi-year plateau before the onset of a monatomic decline rate of 2-5% per year; (2) A Middling Case, where world oil production reaches a maximum, after which it drops into a long-term, 2-5% monotonic annual decline; and finally (3) A Worst Case, where the sharp peak of the Middling Case is degraded by oil exporter withholding, leading to world oil shortages growing potentially more rapidly than 2-5% per year, creating the most dire world economic impacts. (author)

  17. [Pollution hazard for water bodies at oil production].

    Science.gov (United States)

    Zholdakova, Z I; Beliaeva, N I

    2015-01-01

    In the paper there have been summarizes the concepts of the danger of the pollution ofwater bodies in oil production (the most dangerous are reagents used in the drilling, drilling waste, oil and petrochemicals, oil biodestructors. There was shown the danger of the spread of oil pollution. New indices, presenting a hazard during drilling and oil production have been substantiated The tasks aimed to the improvement of the standards and methods of the control of the water pollution by oil, as well as of the documents regulating the conditions of environmental protection during the drilling have been conceived.

  18. Approaches of Russian oil companies to optimal capital structure

    Science.gov (United States)

    Ishuk, T.; Ulyanova, O.; Savchitz, V.

    2015-11-01

    Oil companies play a vital role in Russian economy. Demand for hydrocarbon products will be increasing for the nearest decades simultaneously with the population growth and social needs. Change of raw-material orientation of Russian economy and the transition to the innovative way of the development do not exclude the development of oil industry in future. Moreover, society believes that this sector must bring the Russian economy on to the road of innovative development due to neo-industrialization. To achieve this, the government power as well as capital management of companies are required. To make their optimal capital structure, it is necessary to minimize the capital cost, decrease definite risks under existing limits, and maximize profitability. The capital structure analysis of Russian and foreign oil companies shows different approaches, reasons, as well as conditions and, consequently, equity capital and debt capital relationship and their cost, which demands the effective capital management strategy.

  19. Evolving production network structures

    DEFF Research Database (Denmark)

    Grunow, Martin; Gunther, H.O.; Burdenik, H.

    2007-01-01

    When deciding about future production network configurations, the current structures have to be taken into account. Further, core issues such as the maturity of the products and the capacity requirements for test runs and ramp-ups must be incorporated. Our approach is based on optimization...... modelling and assigns products and capacity expansions to production sites under the above constraints. It also considers the production complexity at the individual sites and the flexibility of the network. Our implementation results for a large manufacturing network reveal substantial possible cost...

  20. Bio Gas Oil Production from Waste Lard

    Directory of Open Access Journals (Sweden)

    Jenő Hancsók

    2011-01-01

    Full Text Available Besides the second generations bio fuels, one of the most promising products is the bio gas oil, which is a high iso-paraffin containing fuel, which could be produced by the catalytic hydrogenation of different triglycerides. To broaden the feedstock of the bio gas oil the catalytic hydrogenation of waste lard over sulphided NiMo/Al2O3 catalyst, and as the second step, the isomerization of the produced normal paraffin rich mixture (intermediate product over Pt/SAPO-11 catalyst was investigated. It was found that both the hydrogenation and the decarboxylation/decarbonylation oxygen removing reactions took place but their ratio depended on the process parameters (T = 280–380∘C, P = 20–80 bar, LHSV = 0.75–3.0 h−1 and H2/lard ratio: 600 Nm3/m3. In case of the isomerization at the favourable process parameters (T = 360–370∘C, P = 40 –50 bar, LHSV = 1.0 h−1 and H2/hydrocarbon ratio: 400 Nm3/m3 mainly mono-branching isoparaffins were obtained. The obtained products are excellent Diesel fuel blending components, which are practically free of heteroatoms.

  1. Production of top quality soybean oil

    Directory of Open Access Journals (Sweden)

    Moustafa, Dr. Ahmad

    1995-12-01

    Full Text Available The paper comments the most adequate conditions required to produce to quality soybean oil. It is essential to avoid contaminations (water, metallic, oxidation products, overheating, undue exposition to air, as well as an appropriate control of the different steps of the refining process.

    El trabajo presenta las condiciones recomendadas para obtener aceite de soja de la mejor calidad. Es importante evitar las contaminaciones (agua, metales y compuestos oxidados, los sobrecalentamientos, la exposición al aire, así como el adecuado control de los diferentes pasos del proceso de refinación.

  2. By-products of palm oil extraction and refining

    Directory of Open Access Journals (Sweden)

    Tan Yew-Ai

    2006-01-01

    Full Text Available This paper outlines the utilisation of by-products resulting from the extraction and refining of palm oil. It summarises research by the Malaysian Palm Oil Board (MPOB directed at producing zero waste from the palm oil industry. MPOB regards by-products of the palm oil industry not as waste but resources. It will be evident that by-products from the palm oil industry can be and have been used extensively and that the research carried out is relevant to both the milling and refining sectors.

  3. An analysis of oil production by OPEC countries. Persistence, breaks, and outliers

    Energy Technology Data Exchange (ETDEWEB)

    Barros, Carlos Pestana [Instituto Superior de Economia e Gestao and Research Unit on Complexity and Economics, Technical University of Lisbon, Lisbon (Portugal); Gil-Alana, Luis A. [University of Navarra, Pamplona (Spain); Payne, James E. [Department of Economics, Illinois State University, Normal, IL 61790-4200 (United States)

    2011-01-15

    This study examines the time series behaviour of oil production for OPEC member countries within a fractional integration modelling framework recognizing the potential for structural breaks and outliers. The analysis is undertaken using monthly data from January 1973 to October 2008 for 13 OPEC member countries. The results indicate there is mean reverting persistence in oil production with breaks identified in 10 out of the 13 countries examined. Thus, shocks affecting the structure of OPEC oil production will have persistent effects in the long run for all countries, and in some cases the effects are expected to be permanent. (author)

  4. Life Cycle Assessment for the Production of Oil Palm Seeds

    OpenAIRE

    Muhamad, Halimah; Ai, Tan Yew; Khairuddin, Nik Sasha Khatrina; Amiruddin, Mohd Din; May, Choo Yuen

    2014-01-01

    The oil palm seed production unit that generates germinated oil palm seeds is the first link in the palm oil supply chain, followed by the nursery to produce seedling, the plantation to produce fresh fruit bunches (FFB), the mill to produce crude palm oil (CPO) and palm kernel, the kernel crushers to produce crude palm kernel oil (CPKO), the refinery to produce refined palm oil (RPO) and finally the palm biodiesel plant to produce palm biodiesel. This assessment aims to investigate the life c...

  5. Good Manufacturing Practice (GMP guidelines for virgin olive oil production

    Directory of Open Access Journals (Sweden)

    Petrakis, Christos

    1994-04-01

    Full Text Available This paper presents GMP guidelines for the production of virgin olive oil. Standard procedures and conditions are indicated for olive production, harvesting, transportation and storage, for oil manufacture, storage and packaging, for buildings, process logistics and the materials used throughout the production chain.

  6. Market analysis of shale oil co-products. Appendices

    Energy Technology Data Exchange (ETDEWEB)

    1980-12-01

    Data are presented in these appendices on the marketing and economic potential for soda ash, aluminia, and nahcolite as by-products of shale oil production. Appendices 1 and 2 contain data on the estimated capital and operating cost of an oil shales/mineral co-products recovery facility. Appendix 3 contains the marketing research data.

  7. Transesterification of Palm Oil for the Production of Biodiesel

    Directory of Open Access Journals (Sweden)

    Khalizani Khalid

    2011-01-01

    Full Text Available Problem statement: Palm oil is known as an important source of edible oil with significant values of renewable energy. Depletion of petroleum had captured much attention on producing biodiesel from the palm oil. Approach: The most concerning methods for the production of biodiesel were discussed, namely transesterification (alkali and acid, enzymetic approach and supercritical alcohol. Results: The results showed the vis-a-vis of the methods for possible consideration of research. Conclusion: Concerning the importance of this vegetable oil, the contribution of palm oil towards diminution of fossil fuel, possible methods for the production of biodiesel and the opportunity for the futures is very much important.

  8. Life Cycle Assessment for the Production of Oil Palm Seeds.

    Science.gov (United States)

    Muhamad, Halimah; Ai, Tan Yew; Khairuddin, Nik Sasha Khatrina; Amiruddin, Mohd Din; May, Choo Yuen

    2014-12-01

    The oil palm seed production unit that generates germinated oil palm seeds is the first link in the palm oil supply chain, followed by the nursery to produce seedling, the plantation to produce fresh fruit bunches (FFB), the mill to produce crude palm oil (CPO) and palm kernel, the kernel crushers to produce crude palm kernel oil (CPKO), the refinery to produce refined palm oil (RPO) and finally the palm biodiesel plant to produce palm biodiesel. This assessment aims to investigate the life cycle assessment (LCA) of germinated oil palm seeds and the use of LCA to identify the stage/s in the production of germinated oil palm seeds that could contribute to the environmental load. The method for the life cycle impact assessment (LCIA) is modelled using SimaPro version 7, (System for Integrated environMental Assessment of PROducts), an internationally established tool used by LCA practitioners. This software contains European and US databases on a number of materials in addition to a variety of European- and US-developed impact assessment methodologies. LCA was successfully conducted for five seed production units and it was found that the environmental impact for the production of germinated oil palm was not significant. The characterised results of the LCIA for the production of 1000 germinated oil palm seeds showed that fossil fuel was the major impact category followed by respiratory inorganics and climate change.

  9. Life-Cycle Assessment of Pyrolysis Bio-Oil Production*

    Energy Technology Data Exchange (ETDEWEB)

    Steele, Philip; Puettmann, Maureen E.; Penmetsa, Venkata Kanthi; Cooper, Jerome E.

    2012-07-01

    As part ofthe Consortium for Research on Renewable Industrial Materials' Phase I life-cycle assessments ofbiofuels, lifecycle inventory burdens from the production of bio-oil were developed and compared with measures for residual fuel oil. Bio-oil feedstock was produced using whole southern pine (Pinus taeda) trees, chipped, and converted into bio-oil by fast pyrolysis. Input parameters and mass and energy balances were derived with Aspen. Mass and energy balances were input to SimaPro to determine the environmental performance of bio-oil compared with residual fuel oil as a heating fuel. Equivalent functional units of 1 MJ were used for demonstrating environmental preference in impact categories, such as fossil fuel use and global warming potential. Results showed near carbon neutrality of the bio-oil. Substituting bio-oil for residual fuel oil, based on the relative carbon emissions of the two fuels, estimated a reduction in CO2 emissions by 0.075 kg CO2 per MJ of fuel combustion or a 70 percent reduction in emission over residual fuel oil. The bio-oil production life-cycle stage consumed 92 percent of the total cradle-to-grave energy requirements, while feedstock collection, preparation, and transportation consumed 4 percent each. This model provides a framework to better understand the major factors affecting greenhouse gas emissions related to bio-oil production and conversion to boiler fuel during fast pyrolysis.

  10. Pretreatment of oil palm empty fruit bunch (OPEFB) by N-methylmorpholine-N-oxide (NMMO) for biogas production: structural changes and digestion improvement.

    Science.gov (United States)

    Purwandari, Fiametta Ayu; Sanjaya, Adhitya Pitara; Millati, Ria; Cahyanto, Muhammad Nur; Horváth, Ilona Sárvári; Niklasson, Claes; Taherzadeh, Mohammad J

    2013-01-01

    Pretreatment of OPEFB (oil palm empty fruit bunch) by NMMO (N-methylmorpholine-N-oxide) on its subsequent digestions was investigated. The pretreatments were carried out at 90 and 120 °C for 1, 3, and 5h in three different modes of dissolution (by 85% NMMO solution), ballooning (79% NMMO solution), and swelling (73% NMMO solution). The total solid recovery after the pretreatment was 89-94%. The pretreatment process did not have a major impact on the composition of OPEFB, other than a reduction of ash from 5.4% up to 1.3%. The best improvement in biogas production was achieved by a dissolution mode pretreatment of OPEFB, using conditions of 85% NMMO, 3h, and 120 °C. It resulted in 0.408 Nm(3)/kg VS methane yield and 0.032 Nm(3)CH(4)/kg VS/day initial methane production rate, which correspond in improving by 48% and 167% compared to the untreated OPEFB, respectively.

  11. Ethyl ester production from (RBD palm oil

    Directory of Open Access Journals (Sweden)

    Oscar Mauricio Martínez Ávila

    2010-07-01

    Full Text Available This work develops a methodology for obtaining ethyl esters from RBD (refined, bleached and deodorised palm oil by evaluating the oil’s transesterification and separation. Two catalysts were first tested (KOH and NaOH by studying the effect of water presence on the reaction. The separation process was then evaluated by using water and water-salt and water-acid mixtures, establishing the agent offering the best results and carrying out the purification stage. Raw materials and products were characterised for comparing the latter with those obtained by traditional means and verifying the quality of the esters so produced; minimum differences were found bet-ween both. The proposed methodology thus allows esters to be used as raw material in petrochemical industry applications. A more profitable process can be obtained compared to those used today, given the amounts of separation agent so established (1% H3PO4 solution, in water. The overall process achieved 74.4% yield, based on the oil being used.

  12. Structure - materials - production

    DEFF Research Database (Denmark)

    Gammelgaard Nielsen, Anders; Gammel, Peder; Busch, Jens

    2002-01-01

    For the last six years th Aarhus School of Architecture has introduced the first year students (there are about 200 students admitted each year) to structure, materials, design and production through a five week course in collaboration with a group of local companies....

  13. The structuring of products and product programmes

    DEFF Research Database (Denmark)

    Andreasen, Mogens myrup; Hansen, Claus thorp; Mortensen, Niels henrik

    1996-01-01

    members may be created by variation.The structuring of products and product families is a complex design task. This article aims at classifying the many structuring types, which are built into a product. The fact that different structures are superimposed in the final product, makes the design synthesis...... complex and raises a need for aids.Among aids for structuring computer support seems feasible. The need for modelling the product and its structural aspects is eluciated. A modelling framework is proposed, and the need for modelling different structure types by use of an enhanced modelling is shown...

  14. Palm oil based surfactant products for petroleum industry

    Science.gov (United States)

    Permadi, P.; Fitria, R.; Hambali, E.

    2017-05-01

    In petroleum production process, many problems causing reduced production are found. These include limited oil recovery, wax deposit, asphaltene deposit, sludge deposit, and emulsion problem. Petroleum-based surfactant has been used to overcome these problems. Therefore, innovation to solve these problems using surfactant containing natural materials deserves to be developed. Palm oil-based surfactant is one of the potential alternatives for this. Various types of derivative products of palm oil-based surfactant have been developed by SBRC IPB to be used in handling problems including surfactant flooding, well stimulation, asphaltene dissolver, well cleaning, and wax removal found in oil and gas industry.

  15. CPECC Contracts Oil Products Pipeline Construction in Pakistan

    Institute of Scientific and Technical Information of China (English)

    Wang Yong

    2002-01-01

    @@ China Petroleum Engineering & Construction Corporation (CPECC), a subsidiary of CNPC, and Pak-Arab Pipeline Company (PARCO) of Pakistan have recently reached an agreement to confirm the US$317-million contract for construction a pipeline for oil products in Pakistan by CPECC. The project is called the white oil pipeline project (WOPP)running from Karachi to Mahmood Kot, the distribution center of oil products in the northwest part of the country.

  16. Oil and Gas Production Wastewater: Soil Contamination and Pollution Prevention

    OpenAIRE

    John Pichtel

    2016-01-01

    During oil and natural gas production, so-called “produced water” comprises the largest byproduct stream. In addition, many oil and gas operations are augmented via injection of hydraulic fracturing (HF) fluids into the formation. Both produced water and HF fluids may contain hundreds of individual chemicals, some known to be detrimental to public health and the environment. Oil and gas production wastewater may serve a range of beneficial purposes, particularly in arid regions, if managed co...

  17. Oil extraction from plant seeds for biodiesel production

    Directory of Open Access Journals (Sweden)

    Yadessa Gonfa Keneni

    2017-04-01

    Full Text Available Energy is basic for development and its demand increases due to rapid population growth, urbanization and improved living standards. Fossil fuels will continue to dominate other sources of energy although it is non-renewable and harm global climate. Problems associated with fossil fuels have driven the search for alternative energy sources of which biodiesel is one option. Biodiesel is renewable, non-toxic, environmental-friendly and an economically feasible options to tackle the depleting fossil fuels and its negative environmental impact. It can be produced from vegetable oils, animal fats, waste oils and algae. However, nowadays, the major feedstocks of biodiesel are edible oils and this has created food vs fuel debate. Therefore, the future prospect is to use non-edible oils, animal fats, waste oils and algae as feedstock for biodiesel. Selection of non-expensive feedstock and the extraction and preparation of oil for biodiesel production is a crucial step due to its relevance on the overall technology. There are three main conventional oil extraction methods: mechanical, chemical/solvent and enzymatic extraction methods. There are also some newly developed oil extraction methods that can be used separately or in combination with the conventional ones, to overcome some disadvantages of the conventional oil extraction methods. This review paper presents, compare and discusses different potential biofuel feedstocks, various oil extraction methods, advantages and disadvantages of different oil extraction methods, and propose future prospective for the improvement of oil extraction methods and sustainability of biodiesel production and utilization.

  18. Physical chemistry of colloids and interfaces in oil production

    Energy Technology Data Exchange (ETDEWEB)

    Toulhoat, H.; Lecourtier, J. (eds.)

    1992-01-01

    The field of colloid and interface science is nowadays the topic of numerous scientific meetings. For want of basic understanding, the problems to which engineer is faced in drilling and oil production operations do not find optimal solutions. Colloid and interface phenomena govern many such problems. Misunderstandings in oil field operations have enormous financial consequences ranging from delays in well drilling to poor evaluations of reserves and low recoveries. The need for advances in colloid and interface science applicable to production process development has been recognized for a long time by the oil industry, and most of its research centers support active programs for that purpose. These proceedings bring important new results on problems like the wettability of reservoir rocks, the relationships between structure and properties of complex drilling fluids, and the transport of colloidal particles and foams in porous media. These proceedings are subdivided into three parts: Interfacial phenomena, complex fluids and colloids in porous media. Five plenary lectures, 27 oral conferences and 36 poster communications have been presented.

  19. Seed structure characteristics to form ultrahigh oil content in rapeseed.

    Directory of Open Access Journals (Sweden)

    Zhi-Yong Hu

    Full Text Available BACKGROUND: Rapeseed (Brassica napus L. is an important oil crop in the world, and increasing its oil content is a major breeding goal. The studies on seed structure and characteristics of different oil content rapeseed could help us to understand the biological mechanism of lipid accumulation, and be helpful for rapeseed breeding. METHODOLOGY/PRINCIPAL FINDINGS: Here we report on the seed ultrastructure of an ultrahigh oil content rapeseed line YN171, whose oil content is 64.8%, and compared with other high and low oil content rapeseed lines. The results indicated that the cytoplasms of cotyledon, radicle, and aleuronic cells were completely filled with oil and protein bodies, and YN171 had a high oil body organelle to cell area ratio for all cell types. In the cotyledon cells, oil body organelles comprised 81% of the total cell area in YN171, but only 53 to 58% in three high oil content lines and 33 to 38% in three low oil content lines. The high oil body organelle to cotyledon cell area ratio and the cotyledon ratio in seed were the main reasons for the ultrahigh oil content of YN171. The correlation analysis indicated that oil content is significantly negatively correlated with protein content, but is not correlated with fatty acid composition. CONCLUSIONS/SIGNIFICANCE: Our results indicate that the oil content of YN171 could be enhanced by increasing the oil body organelle to cell ratio for some cell types. The oil body organelle to seed ratio significantly highly positively correlates with oil content, and could be used to predict seed oil content. Based on the structural analysis of different oil content rapeseed lines, we estimate the maximum of rapeseed oil content could reach 75%. Our results will help us to screen and identify high oil content lines in rapeseed breeding.

  20. Cryo-FIB SEM for Characterization of the Structure of Fish Oil Emulsions

    DEFF Research Database (Denmark)

    Jensen, Louise Helene Søgaard; Horn, Anna Frisenfeldt; Jacobsen, Charlotte;

    2011-01-01

    The addition of fish oil to industrial food products is appealing both to the food industry and consumers for reasons such as health benefits and the extra commercial value. Fish oil is rich in long chain omega-3 fatty acids, which contain a large number of double bonds. This feature causes...... such strategy is to add the oil as an emulsion rather than as neat oil. Studies so far have indicated that emulsification of the fish oil changes the oxidative stability of the product but whether emulsification is an advantage seems to be dependent on the food matrix to which the emulsion is added [1, 2...... can be stabilized by food grade emulsifiers such as proteins and phospholipids from milk. The main objective of this study is to characterize fish oil in water emulsions with respect to oil droplet size, size distribution, and ultimately to view the thickness, structure and morphology of the interface...

  1. Biodiesel Production by Enzymatic Transesterification of Papaya Seed Oil and Rambutan Seed Oil

    Directory of Open Access Journals (Sweden)

    C. S. Wong

    2014-12-01

    Full Text Available Biodiesel production from vegetable oil has gained attention as an alternative fuel to minimize the usage of fossil fuels and reduce greenhouse gases pollution. In Malaysia, oils from local fruit seeds of papaya and rambutan are potential feedstock for biodiesel production due to their high lipid contents and easily available. In the present study, papaya and rambutan seed oils were extracted via soxhlet apparatus using n-hexane and the oil yields were in between 34–40%. The extracted oils were subjected to enzymatic transesterification by the immobilized Candida rugosa lipase as a catalyst under room temperature with varies molar ratios of methanol to oil. The highest biodiesel yield for papaya seed oil and rambutan seed oil was found to be 96% and 89% at methanol-to-oil ratios of 6:1 and 8:1, respectively. Results also showed a higher biodiesel yield using lipase immobilized on the magnetic particles as the heterogeneous catalyst compared to the yield obtained using free enzyme as the homogeneous catalyst. The properties of biodiesel such as density, acid value, iodine value and cetane number were analyzed and found to meet the European Standard of Biodiesel. The study shows that papaya and rambutan seed oils have the potential to be used as alternative feedstock for biodiesel production than the full dependence on palm oil in Malaysia.

  2. Improving environmental sustainability of Thai palm oil production in 2050

    NARCIS (Netherlands)

    Saswattecha, Kanokwan; Kroeze, Carolien; Jawjit, Warit; Hein, Lars

    2017-01-01

    Palm oil production has increased in Thailand with considerable environmental impacts. The aim of this study is to analyse possibilities to examine how the environmental sustainability of Thai palm oil production can be improved in the coming decades. To this end, we integrated a sectoral and a l

  3. Impact of heavy metals on the oil products biodegradation process.

    Science.gov (United States)

    Zukauskaite, Audrone; Jakubauskaite, Viktorija; Belous, Olga; Ambrazaitiene, Dalia; Stasiskiene, Zaneta

    2008-12-01

    Oil products continue to be used as a principal source of energy. Wide-scale production, transport, global use and disposal of petroleum have made them major contaminants in prevalence and quantity in the environment. In accidental spills, actions are taken to remove or remediate or recover the contaminants immediately, especially if they occur in environmentally sensitive areas, for example, in coastal zones. Traditional methods to cope with oil spills are confined to physical containment. Biological methods can have an advantage over the physical-chemical treatment regimes in removing spills in situ as they offer biodegradation of oil fractions by the micro-organisms. Recently, biological methods have been known to play a significant role in bioremediation of oil-polluted coastal areas. Such systems are likely to be of significance in the effective management of sensitive coastal ecosystems chronically subjected to oil spillage. For this reason the aim of this paper is to present an impact of Mn, Cu, Co and Mo quantities on oil biodegradation effectiveness in coastal soil and to determine the relationship between metal concentrations and degradation of two oil products (black oil and diesel fuel). Soil was collected in the Baltic Sea coastal zone oil products degradation area (Klaipeda, Lithuania). The experiment consisted of two parts: study on the influence of micro-elements on the oil product biodegradation process; and analysis of the influence of metal concentration on the number of HDMs. The analysis performed and results obtained address the following areas: impact of metal on a population of hydrocarbon degrading micro-organisms, impact of metals on residual concentrations of oil products, influence of metals on the growth of micro-organisms, inter-relation of metal concentrations with degradation rates. Statistical analysis was made using ;Statgraphics plus' software. The influence of metals on the growth of micro-organisms, the biodegradation process

  4. Food web structure in oil sands reclaimed wetlands.

    Science.gov (United States)

    Kovalenko, K E; Ciborowski, J J H; Daly, C; Dixon, D G; Farwell, A J; Foote, A L; Frederick, K R; Costa, J M Gardner; Kennedy, K; Liber, K; Roy, M C; Slama, C A; Smits, J E G

    2013-07-01

    Boreal wetlands play an important role in global carbon balance. However, their ecosystem function is threatened by direct anthropogenic disturbance and climate change. Oil sands surface mining in the boreal regions of Western Canada denudes tracts of land of organic materials, leaves large areas in need of reclamation, and generates considerable quantities of extraction process-affected materials. Knowledge and validation of reclamation techniques that lead to self-sustaining wetlands has lagged behind development of protocols for reclaiming terrestrial systems. It is important to know whether wetlands reclaimed with oil sands process materials can be restored to levels equivalent to their original ecosystem function. We approached this question by assessing carbon flows and food web structure in naturally formed and oil sands-affected wetlands constructed in 1970-2004 in the postmining landscape. We evaluated whether a prescribed reclamation strategy, involving organic matter amendment, accelerated reclaimed wetland development, leading to wetlands that were more similar to their natural marsh counterparts than wetlands that were not supplemented with organic matter. We measured compartment standing stocks for bacterioplankton, microbial biofilm, macrophytes, detritus, and zoobenthos; concentrations of dissolved organic carbon and residual naphthenic acids; and microbial production, gas fluxes, and aquatic-terrestrial exports (i.e., aquatic insect emergence). The total biomass of several biotic compartments differed significantly between oil sands and reference wetlands. Submerged macrophyte biomass, macroinvertebrate trophic diversity, and predator biomass and richness were lower in oil sands-affected wetlands than in reference wetlands. There was insufficient evidence to conclude that wetland age and wetland amendment with peat-mineral mix mitigate effects of oil sands waste materials on the fully aquatic biota. Although high variability was observed within

  5. the structure of labour market and demand for hired labour for oil ...

    African Journals Online (AJOL)

    DEPT OF AGRICULTURAL ENGINEERING

    Keywords: structure of labour, hired labour, oil palm production, demand elasticities. INTRODUCTION .... theory of the firm, where the farmer seeks to maximize output subject ... signs of the parameters and significance of the student t-statistics ...

  6. CO2 Enhanced Oil Recovery from the Residual Zone - A Sustainable Vision for North Sea Oil Production

    Science.gov (United States)

    Stewart, Jamie; Haszeldine, Stuart; Wilkinson, Mark; Johnson, Gareth

    2014-05-01

    This paper presents a 'new vision for North Sea oil production' where previously unattainable residual oil can be produced with the injection of CO2 that has been captured at power stations or other large industrial emitters. Not only could this process produce incremental oil from a maturing basin, reducing imports, it also has the capability to store large volumes of CO2 which can offset the emissions of additional carbon produced. Around the world oil production from mature basins is in decline and production from UK oil fields peaked in 1998. Other basins around the world have a similar story. Although in the UK a number of tax regimes, such as 'brown field allowances' and 'new field allowances' have been put in place to re-encourage investment, it is recognised that the majority of large discoveries have already been made. However, as a nation our demand for oil remains high and in the last decade imports of crude oil have been steadily increasing. The UK is dependent on crude oil for transport and feedstock for chemical and plastics production. Combined with the necessity to provide energy security, there is a demand to re-assess the potential for CO2 Enhanced Oil Recovery (CO2-EOR) in the UK offshore. Residual oil zones (ROZ) exist where one of a number of natural conditions beyond normal capillary forces have caused the geometry of a field's oil column to be altered after filling [1]. When this re-structuring happens the primary interest to the hydrocarbon industry has in the past been in where the mobile oil has migrated to. However it is now considered that significant oil resource may exist in the residual zone play where the main oil column has been displaced. Saturations within this play are predominantly close to residual saturation (Sr) and would be similar to that of a water-flooded field [2]. Evidence from a number of hydrocarbon fairways shows that, under certain circumstances, these residual zones in US fields are comparable in thickness to the

  7. Hydrocracking of vacuum gas oil-vegetable oil mixtures for biofuels production.

    Science.gov (United States)

    Bezergianni, Stella; Kalogianni, Aggeliki; Vasalos, Iacovos A

    2009-06-01

    Hydrocracking of vacuum gas oil (VGO)--vegetable oil mixtures is a prominent process for the production of biofuels. In this work both pre-hydrotreated and non-hydrotreated VGO are assessed whether they are suitable fossil components in a VGO-vegetable oil mixture as feed-stocks to a hydrocracking process. This assessment indicates the necessity of a VGO pre-hydrotreated step prior to hydrocracking the VGO-vegetable oil mixture. Moreover, the comparison of two different mixing ratios suggests that higher vegetable oil content favors hydrocracking product yields and qualities. Three commercial catalysts of different activity are utilized in order to identify a range of products that can be produced via a hydrocracking route. Finally, the effect of temperature on hydrocracking VGO-vegetable oil mixtures is studied in terms of conversion and selectivity to diesel, jet/kerosene and naphtha.

  8. Environmental Drivers of Differences in Microbial Community Structure in Crude Oil Reservoirs across a Methanogenic Gradient

    OpenAIRE

    Shelton, Jenna L.; Akob, Denise M.; Jennifer C McIntosh; Noah Fierer; Spear, John R.; Warwick, Peter D.; McCray, John E.

    2016-01-01

    Stimulating in situ microbial communities in oil reservoirs to produce natural gas is a potentially viable strategy for recovering additional fossil fuel resources following traditional recovery operations. Little is known about what geochemical parameters drive microbial population dynamics in biodegraded, methanogenic oil reservoirs. We investigated if microbial community structure was significantly impacted by the extent of crude oil biodegradation, extent of biogenic methane production, a...

  9. Produced water management - clean and safe oil and gas production

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    The conference contains 22 presentations on topics within pollution sources and abatement, discharge reductions, water analysis and monitoring, water production, treatment and injection, enhanced recovery, condensate water, produced water markets, separation technologies for oil/gas/condensate and water, oil removal from solids, environmental risks of oil and gas production and environmental impacts on ecosystems and fisheries. Some oil field case histories are presented. The main focus is on the northern areas such as the North Sea, the north Atlantic Ocean and the Barents Sea, and technological aspects (tk)

  10. In Situ Burning Restores the Ecological Function and Structure of an Oil-Impacted Coastal Marsh

    Science.gov (United States)

    Baustian, Joseph; Mendelssohn, Irving; Lin, Qianxin; Rapp, John

    2010-11-01

    As the use of in situ burning for oil spill remediation in coastal wetlands accelerates, the capacity of this procedure to restore the ecological structure and function of oil-impacted wetlands becomes increasingly important. Thus, our research focused on evaluating the functional and structural recovery of a coastal marsh in South Louisiana to an in situ burn following a Hurricane Katrina-induced oil spill. Permanent sampling plots were set up to monitor marsh recovery in the oiled and burned areas as well as non-oiled and non-burned (reference) marshes. Plots were monitored for species composition, stem density, above- and belowground productivity, marsh resiliency, soil chemistry, soil residual oil, and organic matter decomposition. The burn removed the majority of the oil from the marsh, and structurally the marsh recovered rapidly. Plant biomass and species composition returned to control levels within 9 months; however, species richness remained somewhat lower in the oiled and burned areas compared to the reference areas. Recovery of ecological function was also rapid following the in situ burn. Aboveground and belowground plant productivity recovered within one growing season, and although decomposition rates were initially higher in the oiled areas, over time they became equivalent to those in reference sites. Also, marsh resiliency, i.e., the rate of recovery from our applied disturbances, was not affected by the in situ burn. We conclude that in situ burning is an effective way to remove oil and allow ecosystem recovery in coastal marshes.

  11. Modeling Peak Oil and the Geological Constraints on Oil Production

    NARCIS (Netherlands)

    Okullo, S.J.; Reynes, F.; Hofkes, M.W.

    2014-01-01

    We propose a model to reconcile the theory of inter-temporal non-renewable resource depletion with well-known stylized facts concerning the exploitation of exhaustible resources such as oil. Our approach introduces geological constraints into a Hotelling type extraction-exploration model. We show th

  12. Modeling Peak Oil and the Geological Constraints on Oil Production

    NARCIS (Netherlands)

    Okullo, S.J.; Reynes, F.; Hofkes, M.W.

    2014-01-01

    We propose a model to reconcile the theory of inter-temporal non-renewable resource depletion with well-known stylized facts concerning the exploitation of exhaustible resources such as oil. Our approach introduces geological constraints into a Hotelling type extraction-exploration model. We show th

  13. Modeling peak oil and the geological constraints on oil production

    NARCIS (Netherlands)

    Okullo, S.J.; Reynès, F.; Hofkes, M.W.

    2015-01-01

    We propose a model to reconcile the theory of inter-temporal non-renewable resource depletion with well-known stylized facts concerning the exploitation of exhaustible resources such as oil. Our approach introduces geological constraints into a Hotelling type extraction-exploration model. We show

  14. Modeling peak oil and the geological constraints on oil production

    NARCIS (Netherlands)

    Okullo, S.J.; Reynès, F.; Hofkes, M.W.

    2015-01-01

    We propose a model to reconcile the theory of inter-temporal non-renewable resource depletion with well-known stylized facts concerning the exploitation of exhaustible resources such as oil. Our approach introduces geological constraints into a Hotelling type extraction-exploration model. We show th

  15. Structures, Mixed Types - Oil & Gas Locations

    Data.gov (United States)

    NSGIC GIS Inventory (aka Ramona) — An Oil and Gas Location is a DEP primary facility type related to the Oil & Gas Program. The sub-facility types related to Oil and Gas that are included in this...

  16. SINOPEC RAISES 2006 OIL AND GAS PRODUCTION

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    @@ Sinopec Corp., the nation's second-biggest oil company,is expected to produce 1.9 percent more crude oil and 11percent more gas in 2006 as the nation's energy demand continually rises. The company may pump 40 million tons of crude oil and 7 billion cubic meters of natural gas from domestic fields this year, said Sinopec Corp in a statement released in late December. The company produced 39.27million tons of crude oil and 6.3 billion cubic meters of gas last year. Chinese oil companies are increasing investments in oil and gas exploration to meet demands by the world's fastest-growing major economy, which expanded 10.7 percent in the first three quarters of this year.

  17. Response to Oil Sands Products Assessment

    Science.gov (United States)

    2015-09-01

    Tailings ponds are an operating facility common to all types of surface mining. For oil sands, tailings consisting of water , sand, clay, and residual ...oil, are pumped to these basins—or ponds— where settling occurs and water is recycled for reuse in the process. When the ponds are no longer required...of crude oil transported by tank vessel in Washington waters . In a 2013 Bloomburg Business news article , Dan Murtaugh states, “The dock probably

  18. Medicinal and cosmetics soap production from Jatropha oil.

    Science.gov (United States)

    Shahinuzzaman, M; Yaakob, Zahira; Moniruzzaman, M

    2016-06-01

    Soap is the most useful things which we use our everyday life in various cleansing and cosmetics purposes. Jatropha oil is nonedible oil which has more benefits to soap making. It has also cosmetics and medicinal properties. But the presence of toxic Phorbol esters in Jatropha oil is the main constrains to use it. So it is necessary to search a more suitable method for detoxifying the Jatropha oil before the use as the main ingredient of soap production. This review implies a more suitable method for removing phorbol esters from Jatropha oil. Several parameters such as the % yield of pure Jatropha oil soap, TFM value of soap, total alkali content, free caustic alkalinity content, pH, the antimicrobial activity, and CMC value of general soap should be taken into consideration for soap from detoxified Jatropha oil.

  19. Coffee oil as a potential feedstock for biodiesel production.

    Science.gov (United States)

    Oliveira, Leandro S; Franca, Adriana S; Camargos, Rodrigo R S; Ferraz, Vany P

    2008-05-01

    A preliminary evaluation of the feasibility of producing biodiesel using oil extracted from defective coffee beans was conducted as an alternative means of utilizing these beans instead of roasting for consumption of beverage with depreciated quality. Direct transesterifications of triglycerides from refined soybean oil (reference) and from oils extracted from healthy and defective coffee beans were performed. Type of alcohol employed and time were the reaction parameters studied. Sodium methoxide was used as alkaline catalyst. There was optimal phase separation after reactions using both soybean and healthy coffee beans oils when methanol was used. This was not observed when using the oil from defective beans which required further processing to obtain purified alkyl esters. Nevertheless, coffee oil was demonstrated to be a potential feedstock for biodiesel production, both from healthy and defective beans, since the corresponding oils were successfully converted to fatty acid methyl and ethyl esters.

  20. Genetic discovery for oil production and quality in sesame.

    Science.gov (United States)

    Wei, Xin; Liu, Kunyan; Zhang, Yanxin; Feng, Qi; Wang, Linhai; Zhao, Yan; Li, Donghua; Zhao, Qiang; Zhu, Xiaodong; Zhu, Xiaofeng; Li, Wenjun; Fan, Danlin; Gao, Yuan; Lu, Yiqi; Zhang, Xianmei; Tang, Xiumei; Zhou, Congcong; Zhu, Chuanrang; Liu, Lifeng; Zhong, Ruichun; Tian, Qilin; Wen, Ziruo; Weng, Qijun; Han, Bin; Huang, Xuehui; Zhang, Xiurong

    2015-10-19

    Oilseed crops are used to produce vegetable oil. Sesame (Sesamum indicum), an oilseed crop grown worldwide, has high oil content and a small diploid genome, but the genetic basis of oil production and quality is unclear. Here we sequence 705 diverse sesame varieties to construct a haplotype map of the sesame genome and de novo assemble two representative varieties to identify sequence variations. We investigate 56 agronomic traits in four environments and identify 549 associated loci. Examination of the major loci identifies 46 candidate causative genes, including genes related to oil content, fatty acid biosynthesis and yield. Several of the candidate genes for oil content encode enzymes involved in oil metabolism. Two major genes associated with lignification and black pigmentation in the seed coat are also associated with large variation in oil content. These findings may inform breeding and improvement strategies for a broad range of oilseed crops.

  1. NMPC for Oil Reservoir Production Optimization

    DEFF Research Database (Denmark)

    Völcker, Carsten; Jørgensen, John Bagterp; Thomsen, Per Grove

    2011-01-01

    In this paper, we use nonlinear model predictive control (NMPC) to maximize secondary oil recovery from an oil reservoir by controlling two-phase subsurface porous flow using adjustable down-hole control valves. The resulting optimal control problem is nonlinear and large-scale. We solve this pro......In this paper, we use nonlinear model predictive control (NMPC) to maximize secondary oil recovery from an oil reservoir by controlling two-phase subsurface porous flow using adjustable down-hole control valves. The resulting optimal control problem is nonlinear and large-scale. We solve...

  2. Biodiesel production in crude oil contaminated environment using Chlorella vulgaris.

    Science.gov (United States)

    Xaaldi Kalhor, Aadel; Mohammadi Nassab, Adel Dabbagh; Abedi, Ehsan; Bahrami, Ahmad; Movafeghi, Ali

    2016-12-01

    Biodiesel is a valuable alternative to fossil fuels and many countries choose biodiesel as an unconventional energy source. A large number of investigations have been done on microalgae as a source of oil production. In recent years, wastewater pollutions have caused many ecological problems, and therefore, wastewater phycoremediation has attracted the international attention. This paper studied the cultivation of Chlorella vulgaris in a crude oil polluted environment for biodiesel production. Intended concentrations were 10 and 20gperliter (crude oil/water) at two times. The results showed that the growth of C. vulgaris was improved in wastewater and the maximum amount of dry mass and oil was produced at the highest concentration of crude oil (0.41g and 0.15g/l, respectively). In addition, dry mass and oil yield of the microalga were significantly enhanced by increasing the experiment duration.

  3. PetroChina's Oil Production Continues to Climb

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ The discovery of the giant oil field in China's Bohai Bay Basin reveals a bright prospect for PetroChina's business development. The company's oil and gas production in the first quarter of this year rose to 277 million tons of oil equivalent, 3.7 percent up from the same period of the previous year, according to the statement recently released by PetroChina.

  4. Production of Detergent from Castor Oil

    Directory of Open Access Journals (Sweden)

    Abubakar Garba ISAH

    2006-07-01

    Full Text Available This research work was carried out with the objective of extraction of oil from castor seeds and its utilization to produce a synthetic detergent. Solvent extraction method was employed in extracting the oil and the total percent oil yield was found to be 23.8%. The experimentally determined saponification value of the oil was 183.7275mgKOH/g of oil. The detergent efficiency, determined as a measure of the foamability of the detergent was found to be 2.6cm. The pH tests revealed mildly basic properties. The color, scent and efficiency of the detergent were improved with the addition of bleaching agent, perfume and foaming agents respectively.

  5. OPEC and Venezuelan oil production: Evidence against a cartel hypothesis

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, Douglas B., E-mail: DBReynolds@Alaska.ed [Department of Economics, University of Alaska Fairbanks, Fairbanks, AK (United States); Pippenger, Michael K. [Department of Economics, University of Alaska Fairbanks, Fairbanks, AK (United States)

    2010-10-15

    This study revisits the OPEC cartel hypothesis using a case study. A test is conducted to see if Venezuela has its production Granger cause its OPEC quota or whether the OPEC quota for Venezuela Granger causes Venezuelan production. The results show both occur at different times. In the short run, OPEC's oil production quota for Venezuela Granger causes Venezuelan production. However, shortly after cuts, Venezuela cheats on agreements, suggesting a tit-for-tat oligopoly game, which is not anti-competitive. In the long run, we show that Venezuelan oil production Granger causes OPEC's quota for Venezuela, but not vice versa. Having Venezuelan oil production Granger cause OPEC quotas for Venezuela in the long run suggests OPEC does not coordinate outputs as much as it reacts to them. The evidence suggests Venezuela is not a part of an OPEC anti-competitive syndicate even though we show that Venezuelan oil production is low. An alternative explanation for why Venezuela and possibly other OPEC members have low oil production outputs is that institutions and risk aversion, not cartel participation, is the cause. A vector error correction model shows that there is no tendency for Venezuelan oil production to converge to OPEC's quota for Venezuela.

  6. OPEC and Venezuelan oil production. Evidence against a cartel hypothesis

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, Douglas B.; Pippenger, Michael K. [Department of Economics, University of Alaska Fairbanks, Fairbanks, AK (United States)

    2010-10-15

    This study revisits the OPEC cartel hypothesis using a case study. A test is conducted to see if Venezuela has its production Granger cause its OPEC quota or whether the OPEC quota for Venezuela Granger causes Venezuelan production. The results show both occur at different times. In the short run, OPEC's oil production quota for Venezuela Granger causes Venezuelan production. However, shortly after cuts, Venezuela cheats on agreements, suggesting a tit-for-tat oligopoly game, which is not anti-competitive. In the long run, we show that Venezuelan oil production Granger causes OPEC's quota for Venezuela, but not vice versa. Having Venezuelan oil production Granger cause OPEC quotas for Venezuela in the long run suggests OPEC does not coordinate outputs as much as it reacts to them. The evidence suggests Venezuela is not a part of an OPEC anti-competitive syndicate even though we show that Venezuelan oil production is low. An alternative explanation for why Venezuela and possibly other OPEC members have low oil production outputs is that institutions and risk aversion, not cartel participation, is the cause. A vector error correction model shows that there is no tendency for Venezuelan oil production to converge to OPEC's quota for Venezuela. (author)

  7. Sustainability of smallholder palm oil production in Indonesia

    OpenAIRE

    Bertule, Maija; Degn, Lasse Twiggs

    2009-01-01

    Palm oil is a widely used commodity and is part of a number of daily products. It is the most used vegetable oil, not just for food consumption, but also for soap and cosmetics. Recently the search for co2 neutral fuels have spurred demand for palm oil to be used in diesel cars. The large demand have led to a dramatic increase in production in Malaysia and Indonesia, and those two producers make up over total production. This dramatic increase in plantations have led to severe environmental p...

  8. Structure-modification and oil pick-up ability of PHBV as oil sorbent materials

    Institute of Scientific and Technical Information of China (English)

    Xuwen He; Dayi Qian; Bing Wu; Tong Wang

    2003-01-01

    The PHBV (β-hydroxybutyrate-co-β-hydroxyvalerate) foams as oil sorbent materials, which were prepared by salting out method based on PHBV and chloroform additive and their oil pick-up abilities were investigated. And the oil pick-up abilities of different PHBV foams as oil sorbent materials were compared. The results show that with the amount of chloroform additive and sodium chloride increasing, the oil pick-up rates, the oil-keeping rates and the second oil pick-up rates of PHBV foams can increase to different extent. When the amount of sodium chloride was 92%, the ratio of PHBV to chloroform was 1 (g): 14 (mL), the oil pick-up ability of the PHBV foam was optimal. And their oil pick-up ratios can reach 25.51 (26℃) and 27.51 g/g (17℃) in raw oil, which were 4-5 times more than those of PHBV powder. In addition, the structure-modified PHBV as oil sorbent materials also has some advantages, such as three-dimension structure, bio-degradability and good oil pick-up ability, so this kind of green oil sorbent materials will have great perspective in the future.

  9. Calculation of oil production performance of the large giant oil fields in the world: based upon oil fields depletion model; Yuden gentai model ni yoru sekai no ogata kyodai yuden no seisan kyodo ni kansuru ichishisan

    Energy Technology Data Exchange (ETDEWEB)

    Nomoto, S. [Japan Oil Development Co. Ltd., Tokyo (Japan); Fujita, K. [The University of Tokyo, Tokyo (Japan)

    1997-05-01

    Data for large giant oil fields with minable reserves of one billion barrels or more were accumulated to structure a new oil field depletion model and estimate production in each oil field. As a result of analyzing events recognized in large giant oil fields, necessity was made clear to correct the conventional oil depletion model. The newly proposed model changes definitions on the depletion period of time, depletion rate, build-up production (during a time period in which production rate increases) and production in a plateau (a time period in which production becomes constant). Two hundred and twenty-five large giant oil fields were classified into those in a depletion period, an initial development phase, and a plateau period. The following findings were obtained as a result of trial calculations using the new model: under an assumption of demand growth rate of 1.5%, oil field groups in the initial development phase will reach the plateau production in the year 2002, and oil fields in the depletion period will continue production decline, hence the production amount after that year will slow down. Because the oil field groups in the plateau period will shift into decline in 2014, the overall production will decrease. The year 2014 is about ten years later than the estimation given recently by Campbell. Undiscovered resources are outside these discussions. 11 refs., 9 figs., 2 tabs.

  10. Enhanced Microbial Pathways for Methane Production from Oil Shale

    Energy Technology Data Exchange (ETDEWEB)

    Paul Fallgren

    2009-02-15

    Methane from oil shale can potentially provide a significant contribution to natural gas industry, and it may be possible to increase and continue methane production by artificially enhancing methanogenic activity through the addition of various substrate and nutrient treatments. Western Research Institute in conjunction with Pick & Shovel Inc. and the U.S. Department of Energy conducted microcosm and scaled-up reactor studies to investigate the feasibility and optimization of biogenic methane production from oil shale. The microcosm study involving crushed oil shale showed the highest yield of methane was produced from oil shale pretreated with a basic solution and treated with nutrients. Incubation at 30 C, which is the estimated temperature in the subsurface where the oil shale originated, caused and increase in methane production. The methane production eventually decreased when pH of the system was above 9.00. In the scaled-up reactor study, pretreatment of the oil shale with a basic solution, nutrient enhancements, incubation at 30 C, and maintaining pH at circumneutral levels yielded the highest rate of biogenic methane production. From this study, the annual biogenic methane production rate was determined to be as high as 6042 cu. ft/ton oil shale.

  11. Utilizing natural gas huff and puff to enhance production in heavy oil reservoir

    Energy Technology Data Exchange (ETDEWEB)

    Wenlong, G.; Shuhong, W.; Jian, Z.; Xialin, Z. [Society of Petroleum Engineers, Kuala Lumpur (Malaysia)]|[PetroChina Co. Ltd., Beijing (China); Jinzhong, L.; Xiao, M. [China Univ. of Petroleum, Beijing (China)

    2008-10-15

    The L Block in the north structural belt of China's Tuha Basin is a super deep heavy oil reservoir. The gas to oil ratio (GOR) is 12 m{sup 3}/m{sup 3} and the initial bubble point pressure is only 4 MPa. The low production can be attributed to high oil viscosity and low flowability. Although steam injection is the most widely method for heavy oil production in China, it is not suitable for the L Block because of its depth. This paper reviewed pilot tests in which the natural gas huff and puff process was used to enhance production in the L Block. Laboratory experiments that included both conventional and unconventional PVT were conducted to determine the physical property of heavy oil saturated by natural gas. The experiments revealed that the heavy oil can entrap the gas for more than several hours because of its high viscosity. A pseudo bubble point pressure exists much lower than the bubble point pressure in manmade foamy oils, which is relative to the depressurization rate. Elastic energy could be maintained in a wider pressure scope than natural depletion without gas injection. A special experimental apparatus that can stimulate the process of gas huff and puff in the reservoir was also introduced. The foamy oil could be seen during the huff and puff experiment. Most of the oil flowed to the producer in a pseudo single phase, which is among the most important mechanisms for enhancing production. A pilot test of a single well demonstrated that the oil production increased from 1 to 2 cubic metres per day to 5 to 6 cubic metres per day via the natural gas huff and puff process. The stable production period which was 5 to 10 days prior to huff and puff, was prolonged to 91 days in the first cycle and 245 days in the second cycle. 10 refs., 1 tab., 12 figs.

  12. Upgrading of maatjes herring byproducts: production of crude fish oil

    NARCIS (Netherlands)

    Aidos, I.; Padt, van der A.; Boom, R.M.; Luten, J.B.

    2001-01-01

    Fish oil has been extracted from byproducts of the maatjes (salted) herring production using a pilot plant consisting of a mincer, heat exchanger, and three-phase decanter. The crude herring oil obtained had an initial peroxide value (PV), anisidine value (AV) and free fatty acids (FFA) level of onl

  13. RISK ANALYSIS APPLIED IN OIL EXPLORATION AND PRODUCTION

    African Journals Online (AJOL)

    ES Obe

    This research investigated the application of risk analysis to Oil exploration and production. Essentially ... uncertainty in Oil field projects; it reduces the impact of the losses should an unfavourable .... own merit but since the company has limited funds it can be ..... ference, New Orleans, LA, September 27-30. (1998). 8. Seba ...

  14. Production of high-quality fish oil from herring byproducts

    NARCIS (Netherlands)

    Aidos, I.M.

    2002-01-01

    In this work, the feasibility of producing high-quality fish oil from herring byproducts was evaluated in various ways. With this, a contribution has been made to a more efficient usage of natural resources while yielding a high-quality product. Crude oil extracted from herring byproducts is relativ

  15. China's Offshore Oil Production Expected to Rise 19% in 2005

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ CNOOC Limited, of which CNOOC is the parent company, announced its 2005 business strategy and development plan in early February to target itself at a 19 percent increase for oil production over the previous year. The offshore oil giant planned to produce 141-146 million BOE (barrels ofoil equivalent) in 2005.

  16. En-route mechanical activation of viscous oil and oil products transported in railroad tank cars

    Directory of Open Access Journals (Sweden)

    Yerlan MYRZAKHMETOV

    2012-01-01

    Full Text Available The authors of this document are aiming to substantiate the advantages of en-route mechanical activation technology as aids for railroad transportation of viscous oil and oil products in tank cars. The conceptual design implies the use of momentum generated by brake action. This document also contains preliminary data of laboratory research confirming the validity of the developed concept.

  17. Biodiesel Production from Waste Coconut Oil in Coconut Milk Manufacturing

    OpenAIRE

    2013-01-01

    The purpose of this research was to develop a 3 step biodiesel production from waste coconut oil taken from a wastewater pond in a coconut milk manufacturing plant. Special attention was paid to optimizing the first step, acid catalyzed hydrolysis, to convert the waste coconut oil into high free fatty acid oil, 83.32 wt%. The first step was the acid hydrolysis, in order to produce high free fatty acid oil. The optimum condition in acid hydrolysis was 5 % by mass of hydrochloric acid, in order...

  18. China's Offshore Oil Production Rises Sharply in First Quarter

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    @@ China National Offshore Oil Corporation Limited(CNOOC Ltd.),China's largest offshore oil producer,recently released its business results in the first quarter of 2010,showing that its total net production increased 31.9 percent year-on-year to 67.3 million barrels of oil equivalent in the January-March period.The total unaudited revenue of CNOOC Ltd.in the first three months surged 118.5 percent to 30.49 billion yuan (US$4.46 billion)due to soaring crude oil prices and increased output.

  19. Oil Production, The Price Crash and Uncertainty in Climate Change

    Science.gov (United States)

    Murray, J. W.

    2015-12-01

    World oil production increased to about 74 million barrels per day by January 2005, and was fairly constant until 2011 when it started to increase to 77.8 mb/d in 2014. This spectacular increase of 4 mb/d was almost entirely due to a sharp increase in production in the US from shale formations, called light tight oil (LTO). World oil production minus this increase in US LTO Production has been flat since 2005 at about 74 mb/d. When US production starts to decline, world oil production likely will as well. That surge is forecast to end soon because LTO is expensive to produce, the first year decline rates are extremely high requiring many new wells each year to maintain or increase production and the most productive locations have already been drilled. It is unprofitable for the Exploration and Production (E&P) companies. Full-year free cash flow has been negative for most tight oil E&P companies since 2009. The total negative cash flow for the 19 largest E&P companies totaled 10.5B in 2014. The surge in US LTO production created an imbalance in global supply and demand and resulted in a 50% decrease in the price of oil. The tight-oil producers who were are financially marginal at an oil price greater than 90 per barrel are even more so at the lower price. As a result the surge in US production of LTO is declining, making it unlikely that world oil production will exceed the present value of about 28 Gb/yr (equivalent to 75 mb/d) (175 EJ/yr). Many of the SRES (IPCC Special Report on Emission Scenarios) and RCP (IPCC Representative Concentration Pathways) projections (especially RCP 8.5 and 6) require CO2 emissions due to oil consumption in the range of 32 Gb/yr to 57 Gb/yr (200 to 350 EJ/yr). The higher values would require a doubling of world oil production. It is highly uncertain whether the higher CO2 scenarios will be reached. This is an element of uncertainty missing from most considerations of future climate change.

  20. Advances in biofuel production from oil palm and palm oil processing wastes: A review

    OpenAIRE

    Kurnia, Jundika C.; Sachin V. Jangam; Saad Akhtar; Agus P. Sasmito; Mujumdar,Arun S.

    2016-01-01

    Over the last decades, the palm oil industry has been growing rapidly due to increasing demands for food, cosmetic, and hygienic products. Aside from producing palm oil, the industry generates a huge quantity of residues (dry and wet) which can be processed to produce biofuel. Driven by the necessity to find an alternative and renewable energy/fuel resources, numerous technologies have been developed and more are being developed to process oil-palm and palm-oil wastes into biofuel. To further...

  1. Biodiesel Production from Waste Coconut Oil in Coconut Milk Manufacturing

    Directory of Open Access Journals (Sweden)

    Sujinna KARNNASUTA

    2013-12-01

    Full Text Available The purpose of this research was to develop a 3 step biodiesel production from waste coconut oil taken from a wastewater pond in a coconut milk manufacturing plant. Special attention was paid to optimizing the first step, acid catalyzed hydrolysis, to convert the waste coconut oil into high free fatty acid oil, 83.32 wt%. The first step was the acid hydrolysis, in order to produce high free fatty acid oil. The optimum condition in acid hydrolysis was 5 % by mass of hydrochloric acid, in order to produce high free fatty acid oil that could be used as raw material for biodiesel production. The second step was the acid esterification, in order to reduce the FFA and convert FFA to methyl ester. The reduction of the FFA from 83.32 % in high free fatty acid oil to less than 2 % required 3 % by mass of hydrochloric acid, a molar ratio of methanol to oil of 10: 1, and a reaction time of 60 min. The alkaline transesterification in the third step was used triglyceride at 1.0wt% of KOH for catalysis, a molar ratio of methanol to oil of 6:1, and a reaction time of 60 min. The waste coconut oil biodiesel was further evaluated by determining its fuel quality, and most of the properties were well within ASTM and EN standards.

  2. Biodiesel production from residual oils recovered from spent bleaching earth

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Yi-Pin; Chang, James I. [Department of Safety, Health and Environmental Engineering, National Kaohsiung First University of Science and Technology, 1, University Blvd., Yenchao, Kaohsiung (China)

    2010-01-15

    This work was to study technical and economic feasibilities of converting residual oils recovered from spent bleaching earth generated at soybean oil refineries into useable biodiesel. Experimental results showed that fatty acids in the SBE residual oil were hexadecenoic acid (58.19%), stearic acid (21.49%) and oleic acid (20.32%), which were similar to those of vegetable oils. The methyl ester conversion via a transesterification process gave a yield between 85 and 90%. The biodiesel qualities were in reasonable agreement with both EN 14214 and ASTM D6751 standards. A preliminary financial analysis showed that the production cost of biodiesel from SBE oils was significantly lower than the pre-tax price of fossil diesel or those made of vegetable oils or waste cooking oils. The effects of the crude oil price and the investment on the production cost and the investment return period were also conducted. The result showed that the investment would return faster at higher crude oil price. (author)

  3. Methanolysis of Carica papaya Seed Oil for Production of Biodiesel

    Directory of Open Access Journals (Sweden)

    Foluso O. Agunbiade

    2014-01-01

    Full Text Available The future of fossil fuel sources of energy has necessitated the need to search for renewable alternatives. Thus, Carica papaya seed oil (CPSO was employed as feedstock for the production of biodiesel by methanolysis. The seed was obtained locally, dried, and extracted with n-hexane. The CPSO was analyzed for specific gravity, viscosity, iodine value, and saponification value, among others using standard methods. The oil was transesterified by two-stage catalysis with oil to methanol mole ratio of 1 : 9. The biodiesel produced was subjected to standard fuel tests. The seed has an oil yield of 31.2% which is commercially viable. The kinematic viscosity of the oil at 313 K was 27.4 mm2s−1 while that of Carica papaya oil methylester (CPOME was reduced to 3.57 mm2s−1 and the specific gravity was 0.84 comparable with other seed-oil biodiesels and number 2 diesel. Other oil properties were compared favourably with seed oils already documented for biodiesel synthesis. CPOME’s cloud and pour points were 275 K and 274 K, respectively, and relatively higher than other biodiesels and number 2 diesel. CPOME exhibits moderate corrosion of copper strip. The methanolysis improved the fuel properties of the CPOME similar to other biodiesels. CPSO therefore exhibits a potential for biodiesel production.

  4. Is oil consumption constrained by industrial structure? Evidence from China

    Science.gov (United States)

    Jia, Y. Q.; Duan, H. M.

    2017-08-01

    This paper examines whether oil consumption is constrained by output value, applying a cointegration test and an ECM to the primary, secondary, and tertiary sectors in China during 1985-2013. The empirical results indicate that oil consumption in China is constrained by the industrial structure both in the short run and in the long run. Regardless of the time horizon considered, the oil consumption constraint is the lowest for the primary sector as well as the highest for the tertiary sector. This is because the long-term industrial structure formation and the technological level of each sector underlines the existence of long run equilibrium and short run fluctuations of output value and oil consumption, with the latter being constrained by adjustments in industrial structure. In order to decrease the constraining effect of output value on oil consumption, the government should take some measures to improve the utilization rate, reducing the intensity of oil consumption, and secure the supply of oil.

  5. Advances in biofuel production from oil palm and palm oil processing wastes: A review

    Directory of Open Access Journals (Sweden)

    Jundika C. Kurnia

    2016-03-01

    Full Text Available Over the last decades, the palm oil industry has been growing rapidly due to increasing demands for food, cosmetic, and hygienic products. Aside from producing palm oil, the industry generates a huge quantity of residues (dry and wet which can be processed to produce biofuel. Driven by the necessity to find an alternative and renewable energy/fuel resources, numerous technologies have been developed and more are being developed to process oil-palm and palm-oil wastes into biofuel. To further develop these technologies, it is essential to understand the current stage of the industry and technology developments. The objective of this paper is to provide an overview of the palm oil industry, review technologies available to process oil palm and palm oil residues into biofuel, and to summarise the challenges that should be overcome for further development. The paper also discusses the research and development needs, technoeconomics, and life cycle analysis of biofuel production from oil-palm and palm-oil wastes.

  6. Ignitability of crude oil and its oil-in-water products at arctic temperature.

    Science.gov (United States)

    Ranellone, Raymond T; Tukaew, Panyawat; Shi, Xiaochuan; Rangwala, Ali S

    2017-02-15

    A novel platform and procedure were developed to characterize the ignitability of Alaska North Slope (ANS) crude oil and its water-in-oil products with water content up to 60% at low temperatures (-20-0°C). Time to ignition, critical heat flux, in-depth temperature profiles were investigated. It was observed that a cold boundary and consequent low oil temperature increased the thermal inertia of the oil/mixture and consequently the time to sustained ignition also increased. As the water content in the ANS water-in-oil mixture increased, the critical heat flux for ignition was found to increase. This is mainly because of an increase in the thermal conductivity of the mixture with the addition of saltwater. The results of the study can be used towards design of ignition strategies and technologies for in situ burning of oil spills in cold climates such as the Arctic.

  7. Preliminary Calculation of the EROI for the Production of Crude Oil and Light Oil Products in Russia

    Directory of Open Access Journals (Sweden)

    Alexander Safronov

    2014-09-01

    Full Text Available Russia is one of the world’s largest producers of energy resources. The production of energy resources in Russia is profitable both economically and in terms of energy production. Currently, Russian oil and gas companies have a policy of increasing energy efficiency, which will led to an increase in the energy return on investment (EROI of both oil and gas production as a whole, and of separate companies in particular. By our calculations, the EROI for oil production in Russia differs for the different companies, and in 2012 was in the range of 22–35:1. The EROI for light oil products in 2012 was in the range of 5–13:1.

  8. Production of Biodiesel from Chicken Frying Oil

    OpenAIRE

    Emaad T. Bakir; Abdelrahman B. Fadhil

    2011-01-01

    Chicken fried oil was converted into different biodiesels through single step transesterification and two step transesterification, namely acid-base and base–base catalyzed transesterification. Hydrochloric acid and potassium hydroxide with methanol were used for this purpose. The results showed that two step base catalyzed transesterification was better compared to other methods. It resulted in higher yield and better fuel properties. Transesterification of fried chicken oil was monitored by...

  9. Federal Outer Continental Shelf Oil and Gas Production Statistics

    Data.gov (United States)

    Bureau of Ocean Energy Management, Department of the Interior — Federal Outer Continental Shelf Oil and Gas Production Statistics by month and summarized annually. Outer Continental Shelf consists of Gulf of Mexico, Pacific and...

  10. Map service: United States Oil and Gas Production 2008

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This map service displays present and past oil and gas production in the United States, as well as the location and intensity of exploratory drilling outside...

  11. Biodiesel production from Jatropha curcas oil catalyzed by whole ...

    African Journals Online (AJOL)

    my mord

    2013-07-03

    Jul 3, 2013 ... reaction conditions for biodiesel production via transesterification between Jatropha curcas (physic nut) oil and ... to be a potential feedstock for enzyme produced bio- .... The growth rate of A. pullulans var. melanogenum SRY.

  12. Field study of heavy oil viscosity reduction for production transport

    Energy Technology Data Exchange (ETDEWEB)

    Pinto, J.; Annichiariccom, G.; Montanez, M. [Ecopetrol S.A. (Venezuela); Faust, M.; Weathers, T. [Nalco Energy Services (Colombia); Parra, R. [Nalco de Colombia Ltda. (Colombia)

    2011-07-01

    In the heavy oil industry, production and transportation are expensive processes requiring complex equipment and procedures. The main issue with heavy crude oil is its high viscosity. A method using naphtha injection was developed to dilute the fluids and aid in water separation, but this method is expensive and raises safety issues. To reduce naphtha consumption, Ecopetrol and Nalco Energy Services developed a new dispersion technology. This paper presents this technology and the results of its field trial in the Chichimene oil field. Key production indicators were monitored to determine how effective the emulsion method was in enhancing production. Results showed no negative effect on the separation facility or oil and water quality while reducing by 75% the injection of diluent. This paper presents a dispersion technology which successfully reduced the need for naphtha and thus reduced production costs.

  13. Heavy and Thermal Oil Recovery Production Mechanisms, SUPRI TR-127

    Energy Technology Data Exchange (ETDEWEB)

    Kovscek, Anthony R.; Brigham, William E.; Castanier, Louis M.

    2001-09-07

    The program spans a spectrum of topics and is divided into five categories: (i) multiphase flow and rock properties, (ii) hot fluid injection, (iii) primary heavy-oil production, (iv) reservoir definition, and (v) in-situ combustion.

  14. Determining the thermal and physicals properties of oil processing products

    Directory of Open Access Journals (Sweden)

    Viktoria I. Kryvda

    2015-03-01

    Full Text Available In the last decades both technological process’ improvement and primary energy resources saving are the main tasks of oil refineries. Using various oil products does impose an accurate knowledge of their properties. The dispersion analysis applied makes possible to construct a model simulating the primary oil refining products’ and raw materials’ thermal physical properties. As a result of data approximation there were obtained polynomials with coefficients differing from attributable to the studied oil products fractions. The research represents graphic dependences of thermal physical properties on temperature values for diesel oil fraction. The linear character of density and calorific capacity dependencies from temperature is represented with a proportional error in calculations. The relative minimum error is below 2% that confirms the implemented calculations’ adequacy. The resulting model can be used in calculations for further technological process improvements.

  15. Characteristics of bicyclic sesquiterpanes in crude oils and petroleum products.

    Science.gov (United States)

    Yang, Chun; Wang, Zhendi; Hollebone, Bruce P; Brown, Carl E; Landriault, Mike

    2009-05-15

    This study presents a quantitative gas chromatography-mass spectrometry analysis of bicyclic sesquiterpanes (BSs) in numerous crude oils and refined petroleum products including light and mid-range distillate fuels, residual fuels, and lubricating oils collected from various sources. Ten commonly recognized bicyclic sesquiterpanes were determined in all the studied crude oils and diesel range fuels with principal dominance of BS3 (C(15)H(28)), BS5 (C(15)H(28)) and BS10 (C(16)H(30)), while they were generally not detected or in trace in light fuel oils like gasoline and kerosene and most lubricating oils. Laboratory distillation of crude oils demonstrated that sesquiterpanes were highly enriched in the medium distillation fractions of approximately 180 to 481 degrees C and were generally absent or very low in the light distillation fraction (boiling point to approximately 180 degrees C) and the heavy residual fraction (>481 degrees C). The effect of evaporative weathering on a series of diagnostic ratios of sesquiterpanes, n-alkanes, and biomarkers was evaluated with two suites of weathered oil samples. The change of abundance of sesquiterpanes was used to determine the extent of weathering of artificially evaporated crude oils and diesel. In addition to the pentacyclic biomarker C(29) and C(30) alphabeta-hopane, C(15) and C(16) sesquiterpanes might be alternative internal marker compounds to provide a direct way to estimate the depletion of oils, particularly diesels, in oil spill investigations. These findings may offer potential applications for both oil identification and oil-source correlation in cases where the tri- to pentacyclic biomarkers are absent due to refining or environmental weathering of oils.

  16. Catalytic production of conjugated fatty acids and oils.

    Science.gov (United States)

    Philippaerts, An; Goossens, Steven; Jacobs, Pierre A; Sels, Bert F

    2011-06-20

    The reactive double bonds in conjugated vegetable oils are of high interest in industry. Traditionally, conjugated vegetable oils are added to paints, varnishes, and inks to improve their drying properties, while recently there is an increased interest in their use in the production of bioplastics. Besides the industrial applications, also food manufactures are interested in conjugated vegetable oils due to their various positive health effects. While the isomer type is less important for their industrial purposes, the beneficial health effects are mainly associated with the c9,t11, t10,c12 and t9,t11 CLA isomers. The production of CLA-enriched oils as additives in functional foods thus requires a high CLA isomer selectivity. Currently, CLAs are produced by conjugation of oils high in linoleic acid, for example soybean and safflower oil, using homogeneous bases. Although high CLA productivities and very high isomer selectivities are obtained, this process faces many ecological drawbacks. Moreover, CLA-enriched oils can not be produced directly with the homogeneous bases. Literature reports describe many catalytic processes to conjugate linoleic acid, linoleic acid methyl ester, and vegetable oils rich in linoleic acid: biocatalysts, for example enzymes and cells; metal catalysts, for example homogeneous metal complexes and heterogeneous catalysts; and photocatalysts. This Review discusses state-of-the-art catalytic processes in comparison with some new catalytic production routes. For each category of catalytic process, the CLA productivities and the CLA isomer selectivity are compared. Heterogeneous catalysis seems the most attractive approach for CLA production due to its easy recovery process, provided that the competing hydrogenation reaction is limited and the CLA production rate competes with the current homogeneous base catalysis. The most important criteria to obtain high CLA productivity and isomer selectivity are (1) absence of a hydrogen donor, (2

  17. Bioprospecting for oil producing microalgal strains: evaluation of oil and biomass production for ten microalgal strains.

    Science.gov (United States)

    Araujo, Glacio S; Matos, Leonardo J B L; Gonçalves, Luciana R B; Fernandes, Fabiano A N; Farias, Wladimir R L

    2011-04-01

    Microalgae have the ability to grow rapidly, synthesize and accumulate large amounts (approximately 20-50% of dry weight) of lipids. A successful and economically viable algae based oil industry depends on the selection of appropriate algal strains. In this study ten species of microalgae were prospected to determine their suitability for oil production: Chaetoceros gracilis, Chaetoceros mulleri, Chlorella vulgaris, Dunaliella sp., Isochrysis sp., Nannochloropsis oculata, Tetraselmis sp., Tetraselmis chui, Tetraselmis tetrathele and Thalassiosira weissflogii. The study was carried out in 3 L glass flasks subjected to constant aeration and controlled artificial illumination and temperature at two different salinities. After harvesting, the extraction of oil was carried out using the Bligh and Dyer method assisted by ultrasound. Results showed that C. gracilis presented the highest oil content and that C. vulgaris presented the highest oil production. Copyright © 2011 Elsevier Ltd. All rights reserved.

  18. Nonlinear joint dynamics between prices of crude oil and refined products

    Science.gov (United States)

    Zhang, Tao; Ma, Guofeng; Liu, Guangsheng

    2015-02-01

    In this paper, we investigate the relationships between crude oil and refined product prices. We find that nonlinear correlations are stronger in the long-term than in the short-term. Crude oil and product prices are cointegrated and financial crisis in 2007-2008 caused a structural break of the cointegrating relationship. Moreover, different from the findings in most studies, we reveal that the relationships are almost symmetric based on a threshold error correction model. The so-called 'asymmetric relationships' are caused by some outliers and financial crisis. Most of the time, crude oil prices play the major role in the adjustment process of the long-term equilibrium. However, refined product prices dominated crude oil prices during the period of financial crisis. Important policy and risk management implications can be learned from the empirical findings.

  19. Surface structure and properties of plant seed oil bodies.

    Science.gov (United States)

    Tzen, J T; Huang, A H

    1992-04-01

    Storage triacylglycerols (TAG) in plant seeds are present in small discrete intracellular organelles called oil bodies. An oil body has a matrix of TAG, which is surrounded by phospholipids (PL) and alkaline proteins, termed oleosins. Oil bodies isolated from mature maize (Zea mays) embryos maintained their discreteness, but coalesced after treatment with trypsin but not with phospholipase A2 or C. Phospholipase A2 or C exerted its activity on oil bodies only after the exposed portion of oleosins had been removed by trypsin. Attempts were made to reconstitute oil bodies from their constituents. TAG, either extracted from oil bodies or of a 1:2 molar mixture of triolein and trilinolein, in a dilute buffer were sonicated to produce droplets of sizes similar to those of oil bodies; these droplets were unstable and coalesced rapidly. Addition of oil body PL or dioleoyl phosphatidylcholine, with or without charged stearylamine/stearic acid, or oleosins, to the medium before sonication provided limited stabilization effects to the TAG droplets. High stability was achieved only when the TAG were sonicated with both oil body PL (or dioleoyl phosphatidylcholine) and oleosins of proportions similar to or higher than those in the native oil bodies. These stabilized droplets were similar to the isolated oil bodies in chemical properties, and can be considered as reconstituted oil bodies. Reconstituted oil bodies were also produced from TAG of a 1:2 molar mixture of triolein and trilinolein, dioleoyl phosphatidylcholine, and oleosins from rice (Oryza sativa), wheat (Triticum aestivum), rapeseed (Brassica napus), soybean (Glycine max), or jojoba (Simmondsia chinensis). It is concluded that both oleosins and PL are required to stabilize the oil bodies and that oleosins prevent oil bodies from coalescing by providing steric hindrance. A structural model of an oil body is presented. The current findings on seed oil bodies could be extended to the intracellular storage lipid

  20. Oil production by Mortierella isabellina from whey treated with lactase.

    Science.gov (United States)

    Demir, Muammer; Turhan, Irfan; Kucukcetin, Ahmet; Alpkent, Zafer

    2013-01-01

    Whey, a by-product of cheese manufacturing is rich in nutrients such as lactose, proteins, and mineral salts. The fungus Mortierella isabellina was used for production of oil containing γ-linoleic acid (GLA) during fermentation on deproteinized whey permeate (DP-WP) with and without lactase addition. The maximum oil concentration was 3.65 g/L in DP-whey (16.0% lactose) without enzyme treatment. Treatment of DP-WP with lactase resulted in an increase in oil content to 17.13 g/L. Palmitic (22.50-25.80%) and oleic acids (37.60-48.56%) were the major fatty acids along with GLA (2.18-5.48%), linoleic (16.21-22.43%) and stearic acid (3.20-10.08%). This study suggests that whey can be utilized as a feedstock for production of microbial oil.

  1. Do structural oil-market shocks affect stock prices?

    Energy Technology Data Exchange (ETDEWEB)

    Apergis, Nicholas [Department of Banking and Financial Management, University of Piraeus, 80 Karaoli and Dimitriou Str, 18534 Piraeus (Greece); Miller, Stephen M. [Department of Economics, University of Nevada, Las Vegas, Nevada (United States)

    2009-07-15

    This paper investigates how explicit structural shocks that characterize the endogenous character of oil price changes affect stock-market returns in a sample of eight countries - Australia, Canada, France, Germany, Italy, Japan, the United Kingdom, and the United States. For each country, the analysis proceeds in two steps. First, modifying the procedure of Kilian [Not All Oil Price Shocks are Alike: Disentangling Demand and Supply Shocks in the Crude Oil Market. American Economic Review.], we employ a vector error-correction or vector autoregressive model to decompose oil-price changes into three components: oil-supply shocks, global aggregate-demand shocks, and global oil-demand shocks. The last component relates to specific idiosyncratic features of the oil market, such as changes in the precautionary demand concerning the uncertainty about the availability of future oil supplies. Second, recovering the oil-supply shocks, global aggregate-demand shocks, and global oil-demand shocks from the first analysis, we then employ a vector autoregressive model to determine the effects of these structural shocks on the stock market returns in our sample of eight countries. We find that international stock market returns do not respond in a large way to oil market shocks. That is, the significant effects that exist prove small in magnitude. (author)

  2. Market enhancement of shale oil: The native products extraction technology

    Energy Technology Data Exchange (ETDEWEB)

    Bunger, J.W. (Bunger (James W.) and Associates, Inc., Salt Lake City, UT (United States)); DuBow, J.B. (Utah Univ., Salt Lake City, UT (United States))

    1991-10-01

    The overall objective of this work was to assess the feasibility of enhancing shale oil commercialization through SO/NPX technology. Specific objectives were: (1) To determine the properties and characteristics of fractions isolable from shale oil utilizing separation sequences which are based on thermodynamic considerations; (2) To identify product streams of market value for promising technology development; (3)To conduct technology development studies leading to a shale oil extraction and processing sequence which promises economic enhancement of shale oil commercialization; (4) To develop an analytical methodology and model for obtaining engineering design data required for process development; (5) To estimate the economics of SO/NPX including the potential for enhancing the profitability of a commercial-scale shale oil MIS retort.

  3. Technological products to support the Venezuelan heavy oil development

    Energy Technology Data Exchange (ETDEWEB)

    Lopez, J.; Negrin, Z.; Duran, M.; Vilera, M.; Santamaria, F. [PDVSA INTEVEP (Venezuela)

    2011-07-01

    In Venezuela, important reserves of heavy oil crude are located at the Orinoco oil belt and the challenge is to develop these fields in a safe and environmentally friendly way. To address this challenge, PDVSA Intevep has been developing cutting edge technologies for more than 30 years. The aim of this paper is to present the principal inventions of PDVSA Intevep and their application in the Venezuelan traditional areas. PDVSA Intevep is the technological development and research center of the Venezuelan national oil industry; they own 773 patents, 103 trademarks, 48 copyrights, 13 trade secrets and 35 products used in different technological areas. The technologies presented will be used in the Orinoco oil belt in support of Venezuelan technological sovereignty. PDVSA Intevep has developed and adapted many technologies aimed at putting oil resources at the service of the whole population and ending social inequalities.

  4. Borehole radar for oil production monitoring

    NARCIS (Netherlands)

    Miorali, M.

    2012-01-01

    The area of smart well technology, or closed-loop reservoir management, aims at enhancing oil recovery through a combination of monitoring and control. Monitoring is performed with a wide range of sensors deployed downhole or at the surface. These sensors allow for capturing changes in the reservoir

  5. Caspian Oil and Gas: Production and Prospects

    Science.gov (United States)

    2005-03-04

    Statistical Review of World Energy 2004, June 15, 2004; Department of Energy, Energy Information Administration (EIA). Caspian Sea Region Country...oil and gas. e Includes Denmark, Germany, Netherlands, Norway, and United Kingdom. Sources: BP. BP Statistical Review of World Energy 2004. June 15

  6. Avocado oil extraction processes: method for cold-pressed high-quality edible oil production versus traditional production

    Directory of Open Access Journals (Sweden)

    Giacomo Costagli

    2015-10-01

    Full Text Available Nowadays the avocado fruit (Persea americana Mill. is widely regarded as an important fruit for its nutritional values, as it is rich in vital human nutrients. The avocado fruit is mainly sold fresh on the market, which however trades also a relevant quantity of second-grade fruits with a relatively high oil content. Traditionally, this oil is extracted from dried fruits by means of organic solvents, but a mechanical method is also used in general in locations where drying systems and/or solvent extraction units cannot be installed. These traditional processes yield a grade of oil that needs subsequent refining and is mainly used in the cosmetic industry. In the late 1990s, in New Zeland, a processing company with the collaboration of Alfa Laval began producing cold-pressed avocado oil (CPAO to be sold as edible oil for salads and cooking. Over the last fifteen years, CPAO production has increased in many other countries and has led to an expansion of the market which is set to continue, given the growing interest in highquality and healthy food. Avocado oil like olive oil is extracted from the fruit pulp and in particular shares many principles of the extraction process with extra-vergin olive oil. We conducted a review of traditional and modern extraction methods with particular focus on extraction processes and technology for CPAO production.

  7. Russian market of oil and fat products in a competitive environment

    Directory of Open Access Journals (Sweden)

    S. M. Ryzhkova

    2016-01-01

    Full Text Available The effective development of the Russian market of oil and fat products, as part of the food market, food security is an essential factor. Russia as a whole is fully self-sufficient in oil and it is a major exporter. Russia has the advantage that, in fact, all of its territory is suitable for cultivation of oilseed crops. In fact, in every region can grow oilseeds, which are in demand on the world market. Products include oil and fat industry for products deep processing and multi-functional. The peculiarity of the Russian market of oilseeds is the diversity of its constituent markets. The Russian market is represented by a different range of fat and oil products domestic and foreign manufacturers. In this market, working as large agricultural holdings and small manufacturers, and processors. The purpose of the study is to study on the basis of indicators that characterize the current state of the Russian market of oil and fat products, a comparison of the situation and of the experience of large processors, identify measures to further the efficient and competitive development of the market for the long term. The study used the abstract logic, monographic, economic and statistical methods. In a competitive environment, to stay on the market, Fat organizations form its structure in the form of vertical integration of multidisciplinary groups, in addition to processing plants that include agribusiness organization, logistics units – transportation, elevators, trading houses. For the development of the market of oil and fat products necessary to improve the competitiveness of domestic products, to revive production of traditional domestic oilseeds led to crop rotation, new, high-tech, innovative use of technology, to develop export, search for new markets. The results can then be used to develop long-term programs of development of regions. Conclusions and recommendations will contribute to a competitive mechanism of functioning and development

  8. Peaking of world oil production: Impacts, mitigation, & risk management

    Energy Technology Data Exchange (ETDEWEB)

    Hirsch, R.L. (SAIC); Bezdek, Roger (MISI); Wendling, Robert (MISI)

    2005-02-01

    The peaking of world oil production presents the U.S. and the world with an unprecedented risk management problem. As peaking is approached, liquid fuel prices and price volatility will increase dramatically, and, without timely mitigation, the economic, social, and political costs will be unprecedented. Viable mitigation options exist on both the supply and demand sides, but to have substantial impact, they must be initiated more than a decade in advance of peaking.... The purpose of this analysis was to identify the critical issues surrounding the occurrence and mitigation of world oil production peaking. We simplified many of the complexities in an effort to provide a transparent analysis. Nevertheless, our study is neither simple nor brief. We recognize that when oil prices escalate dramatically, there will be demand and economic impacts that will alter our simplified assumptions. Consideration of those feedbacks will be a daunting task but one that should be undertaken. Our aim in this study is to-- • Summarize the difficulties of oil production forecasting; • Identify the fundamentals that show why world oil production peaking is such a unique challenge; • Show why mitigation will take a decade or more of intense effort; • Examine the potential economic effects of oil peaking; • Describe what might be accomplished under three example mitigation scenarios. • Stimulate serious discussion of the problem, suggest more definitive studies, and engender interest in timely action to mitigate its impacts.

  9. Biodiesel production from seed oil of Cleome viscosa L.

    Science.gov (United States)

    Kumari, Rashmi; Jain, Vinod Kumar; Kumar, Sushil

    2012-07-01

    Edible oil seed crops, such as rapeseed, sunflower, soyabean and safflower and non-edible seed oil plantation crops Jatropha and Pongamia have proved to be internationally viable commercial sources of vegetable oils for biodiesel production. Considering the paucity of edible oils and unsustainability of arable land under perennial plantation of Jatropha and Pongamia in countries such as India, the prospects of seed oil producing Cleome viscosa, an annual wild short duration plant species of the Indogangetic plains, were evaluated for it to serve as a resource for biodiesel. The seeds of C. viscosa resourced from its natural populations growing in Rajasthan, Haryana and Delhi areas of Aravali range were solvent extracted to obtain the seed oil. The oil was observed to be similar in fatty acid composition to the non-edible oils of rubber, Jatropha and Pongamia plantation crops and soybean, sunflower, safflower, linseed and rapeseed edible oil plants in richness of unsaturated fatty acids. The Cleome oil shared the properties of viscosity, density, saponification and calorific values with the Jatropha and Pongamia oils, except that it was comparatively acidic. The C. viscosa biodiesel had the properties of standard biodiesel specified by ASTM and Indian Standard Bureau, except that it had low oxidation stability. It proved to be similar to Jatropha biodiesel except in cloud point, pour point, cold filter plugging point and oxidation stability. In view of the annual habit of species and biodiesel quality, it can be concluded that C. viscosa has prospects to be developed into a short-duration biodiesel crop.

  10. Oil industry waste: a potential feedstock for biodiesel production.

    Science.gov (United States)

    Abbas, Javeria; Hussain, Sabir; Iqbal, Muhammad Javid; Nadeem, Habibullah; Qasim, Muhammad; Hina, Saadia; Hafeez, Farhan

    2016-08-01

    The worldwide rising energy demands and the concerns about the sustainability of fossil fuels have led to the search for some low-cost renewable fuels. In this scenario, the production of biodiesel from various vegetable and animal sources has attracted worldwide attention. The present study was conducted to evaluate the production of biodiesel from the oil industry waste following base-catalysed transesterification. The transesterification reaction gave a yield of 83.7% by 6:1 methanol/oil molar ratio, at 60°C over 80 min of reaction time in the presence of NaOH. The gas chromatographic analysis of the product showed the presence of 16 fatty acid methyl esters with linoleic and oleic acid as principal components representing about 31% and 20.7% of the total methyl esters, respectively. The fourier transform infrared spectroscopy spectrum of oil industry waste and transesterified product further confirmed the formation of methyl esters. Furthermore, the fuel properties of oil industry waste methyl esters, such as kinematic viscosity, cetane number, cloud point, pour point, flash point, acid value, sulphur content, cold filter plugging point, copper strip corrosion, density, oxidative stability, higher heating values, ash content, water content, methanol content and total glycerol content, were determined and discussed in the light of ASTM D6751 and EN 14214 biodiesel standards. Overall, this study presents the production of biodiesel from the oil industry waste as an approach of recycling this waste into value-added products.

  11. Biotechnological processes for biodiesel production using alternative oils

    Energy Technology Data Exchange (ETDEWEB)

    Azocar, Laura; Ciudad, Gustavo [La Frontera Univ., Temuco (Chile). Nucleo Cietifico Tecnologico en Biorrecursos; Heipieper, Hermann J. [Helmholtz Centre for Environmental Research-UFZ, Leipzig (Germany). Dept. of Environmental Biotechnology; Navia, Rodrigo [La Frontera Univ., Temuco (Chile). Nucleo Cietifico Tecnologico en Biorrecursos; La Frontera Univ., Temuco (Chile). Dept. de Ingenieria Quimica

    2010-10-15

    As biodiesel (fatty acid methyl ester (FAME)) is mainly produced from edible vegetable oils, crop soils are used for its production, increasing deforestation and producing a fuel more expensive than diesel. The use of waste lipids such as waste frying oils, waste fats, and soapstock has been proposed as low-cost alternative feedstocks. Non-edible oils such as jatropha, pongamia, and rubber seed oil are also economically attractive. In addition, microalgae, bacteria, yeast, and fungi with 20% or higher lipid content are oleaginous microorganisms known as single cell oil and have been proposed as feedstocks for FAME production. Alternative feedstocks are characterized by their elevated acid value due to the high level of free fatty acid (FFA) content, causing undesirable saponification reactions when an alkaline catalyst is used in the transesterification reaction. The production of soap consumes the conventional catalyst, diminishing FAME production yield and simultaneously preventing the effective separation of the produced FAME from the glycerin phase. These problems could be solved using biological catalysts, such as lipases or whole-cell catalysts, avoiding soap production as the FFAs are esterified to FAME. In addition, by-product glycerol can be easily recovered, and the purification of FAME is simplified using biological catalysts. (orig.)

  12. Biotechnological processes for biodiesel production using alternative oils.

    Science.gov (United States)

    Azócar, Laura; Ciudad, Gustavo; Heipieper, Hermann J; Navia, Rodrigo

    2010-10-01

    As biodiesel (fatty acid methyl ester (FAME)) is mainly produced from edible vegetable oils, crop soils are used for its production, increasing deforestation and producing a fuel more expensive than diesel. The use of waste lipids such as waste frying oils, waste fats, and soapstock has been proposed as low-cost alternative feedstocks. Non-edible oils such as jatropha, pongamia, and rubber seed oil are also economically attractive. In addition, microalgae, bacteria, yeast, and fungi with 20% or higher lipid content are oleaginous microorganisms known as single cell oil and have been proposed as feedstocks for FAME production. Alternative feedstocks are characterized by their elevated acid value due to the high level of free fatty acid (FFA) content, causing undesirable saponification reactions when an alkaline catalyst is used in the transesterification reaction. The production of soap consumes the conventional catalyst, diminishing FAME production yield and simultaneously preventing the effective separation of the produced FAME from the glycerin phase. These problems could be solved using biological catalysts, such as lipases or whole-cell catalysts, avoiding soap production as the FFAs are esterified to FAME. In addition, by-product glycerol can be easily recovered, and the purification of FAME is simplified using biological catalysts.

  13. Method for creating high carbon content products from biomass oil

    Science.gov (United States)

    Parker, Reginald; Seames, Wayne

    2012-12-18

    In a method for producing high carbon content products from biomass, a biomass oil is added to a cracking reactor vessel. The biomass oil is heated to a temperature ranging from about 100.degree. C. to about 800.degree. C. at a pressure ranging from about vacuum conditions to about 20,700 kPa for a time sufficient to crack the biomass oil. Tar is separated from the cracked biomass oil. The tar is heated to a temperature ranging from about 200.degree. C. to about 1500.degree. C. at a pressure ranging from about vacuum conditions to about 20,700 kPa for a time sufficient to reduce the tar to a high carbon content product containing at least about 50% carbon by weight.

  14. Use of calcium oxide in palm oil methyl ester production

    Directory of Open Access Journals (Sweden)

    Kulchanat Prasertsit

    2014-04-01

    Full Text Available Introducing an untreated calcium oxide (CaO as a solid heterogeneous catalyst for biodiesel production from palm oil by transesterification was studied in this work. The four studied parameters were methanol to oil molar ratio, CaO catalyst concentration, reaction time, and water content. The results for palm oil show that when the water content is higher than 3%wt and the amount of CaO greater than 7%wt soap formation from saponification occurs. A higher methanol to oil molar ratio requires a higher amount of CaO catalyst to provide the higher product purity. The appropriate methanol to CaO catalyst ratio is about 1.56. Commercial grade CaO gives almost the same results as AR grade CaO. In addition, reusing commercial grade CaO for about 5 to 10 repetitions without catalyst regeneration drops the percentage of methyl ester purity approximately 5 to 10%, respectively.

  15. Biodiesel Production from Rubber Seed Oil via Esterification Process

    Directory of Open Access Journals (Sweden)

    W Widayat

    2012-07-01

    Full Text Available One promise source of alternative energy is biodiesel from rubber seed oil, because the raw materials available in plentiful quantities and can be renewed. In addition, the rubber seed is still lack of utilization, and Indonesia is one of the largest rubbers producing country in the world. The objective of this research is to studied on biodiesel production by esterification process. Parameters used in this study are the ratio of catalyst and temperature and its influence on the characteristics of the resulting biodiesel product. Characterization of rubber seed include acid content number analysis, saponification numbers, density, viscosity, iodine number, type of free fatty acids and triglyceride oils. The results of analysis showed that rubber seed oil content obtained is 50.5%. The results of the GCMS analysis showed that a free fatty acid level in rubber seed is very high. Conversion into bio-diesel oil is obtained by at most 59.91% and lowest 48.24%.

  16. Opportunities to improve oil productivity in unstructured deltaic reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-01

    This report contains presentations presented at a technical symposium on oil production. Chapter 1 contains summaries of the presentations given at the Department of Energy (DOE)-sponsored symposium and key points of the discussions that followed. Chapter 2 characterizes the light oil resource from fluvial-dominated deltaic reservoirs in the Tertiary Oil Recovery Information System (TORIS). An analysis of enhanced oil recovery (EOR) and advanced secondary recovery (ASR) potential for fluvial-dominated deltaic reservoirs based on recovery performance and economic modeling as well as the potential resource loss due to well abandonments is presented. Chapter 3 provides a summary of the general reservoir characteristics and properties within deltaic deposits. It is not exhaustive treatise, rather it is intended to provide some basic information about geologic, reservoir, and production characteristics of deltaic reservoirs, and the resulting recovery problems.

  17. Thermodynamic analysis of oil and gas platforms over various production profiles and feed compositions

    DEFF Research Database (Denmark)

    Nguyen, Tuong-Van; Junior, Silvio de Oliveira

    2017-01-01

    Oil and gas platforms present similar structural designs but process fluids with different thermo-physical and chemical properties. In addition, the field properties, such as the gas-to-oil and water-to-oil ratios, change significantly over time. It is therefore not possible to suggest a standard...... of energy and exergy. Feed compositions and production profiles, which correspond to data from actual fields, are used for calibrating the simulations. In a second step, the minimum energy and exergy losses of the platform are assessed by performing thermodynamic analyses, assuming an ideal scenario...... in which all processes are run at their design points. This approach proves to be useful for evaluating consistently different options for oil and gas production, and for determining, in a further step, the most promising solutions for minimising the energy use over a field lifetime....

  18. A Vernonia Diacylglycerol Acyltransferase Can Increase Renewable Oil Production.

    Science.gov (United States)

    Hatanaka, Tomoko; Serson, William; Li, Runzhi; Armstrong, Paul; Yu, Keshun; Pfeiffer, Todd; Li, Xi-Le; Hildebrand, David

    2016-09-28

    Increasing the production of plant oils such as soybean oil as a renewable resource for food and fuel is valuable. Successful breeding for higher oil levels in soybean, however, usually results in reduced protein, a second valuable seed component. This study shows that by manipulating a highly active acyl-CoA:diacylglycerol acyltransferase (DGAT) the hydrocarbon flux to oil in oilseeds can be increased without reducing the protein component. Compared to other plant DGATs, a DGAT from Vernonia galamensis (VgDGAT1A) produces much higher oil synthesis and accumulation activity in yeast, insect cells, and soybean. Soybean lines expressing VgDGAT1A show a 4% increase in oil content without reductions in seed protein contents or yield per unit land area. Incorporation of this trait into 50% of soybeans worldwide could result in an increase of 850 million kg oil/year without new land use or inputs and be worth ∼U.S.$1 billion/year at 2012 production and market prices.

  19. Conversion of Crude Oil to Methane by a Microbial Consortium Enriched From Oil Reservoir Production Waters

    Directory of Open Access Journals (Sweden)

    Carolina eBerdugo-Clavijo

    2014-05-01

    Full Text Available The methanogenic biodegradation of crude oil is an important process occurring in petroleum reservoirs and other oil-containing environments such as contaminated aquifers. In this process, syntrophic bacteria degrade hydrocarbon substrates to products such as acetate, and/or H2 and CO2 that are then used by methanogens to produce methane in a thermodynamically dependent manner. We enriched a methanogenic crude oil-degrading consortium from production waters sampled from a low temperature heavy oil reservoir. Alkylsuccinates indicative of fumarate addition to C5 and C6 n-alkanes were identified in the culture (above levels found in controls, corresponding to the detection of an alkyl succinate synthase gene (assA in the culture. In addition, the enrichment culture was tested for its ability to produce methane from residual oil in a sandstone-packed column system simulating a mature field. Methane production rates of up 5.8 μmol CH4/g of oil/day were measured in the column system. Amounts of produced methane were in relatively good agreement with hydrocarbon loss showing depletion of more than 50% of saturate and aromatic hydrocarbons. Microbial community analysis revealed that the enrichment culture was dominated by members of the genus Smithella, Methanosaeta, and Methanoculleus. However, a shift in microbial community occurred following incubation of the enrichment in the sandstone columns. Here, Methanobacterium sp. were most abundant, as were bacterial members of the genus Pseudomonas and other known biofilm forming organisms. Our findings show that microorganisms enriched from petroleum reservoir waters can bioconvert crude oil components to methane both planktonically and in sandstone-packed columns as test systems. Further, the results suggest that different organisms may contribute to oil biodegradation within different phases (e.g., planktonic versus sessile within a subsurface crude oil reservoir.

  20. Enzymatic interesterification of vegetable oil/ fish oil blend for margarine production

    DEFF Research Database (Denmark)

    Ibrahim, Nuzul Amri Bin; Xu, Xuebing

    the desired properties. In this study, palm stearin (PS), palm kernel oil (PKO) and fish oil (FO) are blended and modified by enzymatic interesterification. PS functioned as the hard stock, PKO as the soft oil and FO as a source for eicosapentaenoic acid (EPA)/ docosahexaenoic acid (DHA). The purpose......In margarine formulation, oils of different melting points are blended to make a product that is spreadable at room temperature. Usually, the blend would be subjected to modification process, either by interesterification (chemical or enzymatic) or partial hydrogenation in order to achieve...... they are consumed as a quick source of energy. The remaining 2-monoacyl- glycerol becomes a source of essential fatty acid, after being absorbed through the intestinal wall. This would enhance the nutritional value of the enzymatically interesterified product. However, the incorporation of FO into the blend would...

  1. Enzymatic interesterification of vegetable oil/ fish oil blend for margarine production

    DEFF Research Database (Denmark)

    Ibrahim, Nuzul Amri Bin; Xu, Xuebing

    In margarine formulation, oils of different melting points are blended to make a product that is spreadable at room temperature. Usually, the blend would be subjected to modification process, either by interesterification (chemical or enzymatic) or partial hydrogenation in order to achieve...... the desired properties. In this study, palm stearin (PS), palm kernel oil (PKO) and fish oil (FO) are blended and modified by enzymatic interesterification. PS functioned as the hard stock, PKO as the soft oil and FO as a source for eicosapentaenoic acid (EPA)/ docosahexaenoic acid (DHA). The purpose...... they are consumed as a quick source of energy. The remaining 2-monoacyl- glycerol becomes a source of essential fatty acid, after being absorbed through the intestinal wall. This would enhance the nutritional value of the enzymatically interesterified product. However, the incorporation of FO into the blend would...

  2. Large-scale biohydrogen production from bio-oil.

    Science.gov (United States)

    Sarkar, Susanjib; Kumar, Amit

    2010-10-01

    Large amount of hydrogen is consumed during the upgrading of bitumen into synthetic crude oil (SCO), and this hydrogen is exclusively produced from natural gas in Western Canada. Because of large amount of emission from natural gas, alternative sources for hydrogen fuel especially renewable feedstocks could significantly reduce CO(2) emissions. In this study, biomass is converted to bio-oil by fast pyrolysis. This bio-oil is steam reformed near bitumen upgrading plant for producing hydrogen fuel. A techno-economic model is developed to estimate the cost of hydrogen from biomass through the pathway of fast pyrolysis. Three different feedstocks including whole-tree biomass, forest residues (i.e. limbs, branches, and tops of tree produced during logging operations), and straw (mostly from wheat and barley crops) are considered for biohydrogen production. Delivered cost of biohydrogen from whole-tree-based biomass ($2.40/kg of H(2)) is lower than that of forest residues ($3.00/kg of H(2)) and agricultural residues ($4.55/kg of H(2)) at a plant capacity of 2000 dry tonnes/day. In this study, bio-oil is produced in the field/forest and transported to a distance of 500 km from the centralized remote bio-oil production plant to bitumen upgrading plant. Feedstock delivery cost and capital cost are the largest cost contributors to the bio-oil production cost, while more than 50% of the cost of biohydrogen production is contributed by bio-oil production and transportation. Carbon credits of $133, $214, and $356/tonne of CO(2) equivalent could make whole-tree, forest residues, and straw-based biohydrogen production competitive with natural gas-based H(2) for a natural gas price of $5/GJ, respectively.

  3. Regional Oil Extraction and Consumption: A simple production model for the next 35 years Part I

    CERN Document Server

    Dittmar, Michael

    2016-01-01

    The growing conflicts in and about oil exporting regions and speculations about volatile oil prices during the last decade have renewed the public interest in predictions for the near future oil production and consumption. Unfortunately, studies from only 10 years ago, which tried to forecast the oil production during the next 20-30 years, failed to make accurate predictions for today's global oil production and consumption. Forecasts using economic growth scenarios, overestimated the actual oil production, while models which tried to estimate the maximum future oil production/year, using the official country oil reserve data, predicted a too low production. In this paper, a new approach to model the maximal future regional and thus global oil production (part I) and consumption (part II) during the next decades is proposed. Our analysis of the regional oil production data during past decades shows that, in contrast to periods when production was growing and growth rates varied greatly from one country to ano...

  4. Borehole radar for oil production monitoring

    OpenAIRE

    Miorali, M.

    2012-01-01

    The area of smart well technology, or closed-loop reservoir management, aims at enhancing oil recovery through a combination of monitoring and control. Monitoring is performed with a wide range of sensors deployed downhole or at the surface. These sensors allow for capturing changes in the reservoir conditions, mainly the fluid movement, at different resolutions. Downhole sensors give information of the fluid entering the well and sample only the region immediately adjacent to the well. Reser...

  5. Oil Products Pricing Criterion Needs Reforming

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ On January 11th, 2007 the price of WTI (West Texas intermediate) crude oil futures dropped to the lowest point of US$51.9 per barrel since June 2005. The National Development and Reform Commission(NDRC) issued a notice on January14th, 2007 deciding to reduce the price of gasoline by RMB220 per ton to RMB4 980 per ton from the same day.

  6. Dubai to take control of its oil production

    Energy Technology Data Exchange (ETDEWEB)

    Anon

    2006-09-15

    The government of Dubai is to take control of the emirate's oil production. From 2nd April, 2007, the foreign consortium responsible for nearly all of Dubai's production will cease to operate the concession and be replaced by a new state-owned company, bringing to an end an era that has lasted over forty years. (author)

  7. Utilization of papaya waste and oil production by Chlorella protothecoides

    Science.gov (United States)

    Algae derived oils have outstanding potential for use in biodiesel production. Chlorella protothecoides has been shown to accumulate lipid up to 60% of its cellular dry weight with glucose supplementation under heterotrophic growth conditions. To reduce production costs, alternative carbon feedstock...

  8. Oil and Gas Production Wastewater: Soil Contamination and Pollution Prevention

    Directory of Open Access Journals (Sweden)

    John Pichtel

    2016-01-01

    Full Text Available During oil and natural gas production, so-called “produced water” comprises the largest byproduct stream. In addition, many oil and gas operations are augmented via injection of hydraulic fracturing (HF fluids into the formation. Both produced water and HF fluids may contain hundreds of individual chemicals, some known to be detrimental to public health and the environment. Oil and gas production wastewater may serve a range of beneficial purposes, particularly in arid regions, if managed correctly. Numerous treatment technologies have been developed that allow for injection, discharge to the land surface, or beneficial reuse. Although many papers have addressed the effects of oil and gas production wastewater (OGPW on groundwater and surface water quality, significantly less information is available on the effects of these fluids on the soil resource. This review paper compiles fundamental information on numerous chemicals used and produced during oil and gas development and their effects on the soil environment. Additionally, pollution prevention technologies relating to OGPW are presented. An understanding of the effects of OGPW on soil chemical, physical, and biological properties can provide a foundation for effective remediation of OGPW-affected soils; additionally, sustainable reuse of oil and gas water for irrigation and industrial purposes may be enhanced.

  9. Past, Present, and Future Production of Bio-oil

    Energy Technology Data Exchange (ETDEWEB)

    Steele, Philip; Yu, Fei; Gajjela, Sanjeev

    2009-04-01

    Bio-oil is a liquid product produced by fast pyrol-ysis of biomass. The fast pyrolysis is performed by heating the biomass rapidly (2 sec) at temperatures ranging from 350 to 650 oC. The vapors produced by this rapid heating are then condensed to produce a dark brown water-based emulsion composed of frag-ments of the original hemicellulose, cellulose and lignin molecules contained in the biomass. Yields range from 60 to 75% based on the feedstock type and the pyrolysis reactor employed. The bio-oil pro-duced by this process has a number of negative prop-erties that are produced mainly by the high oxygen content (40 to 50%) contributed by that contained in water (25 to 30% of total mass) and oxygenated compounds. Each bio-oil contains hundreds of chemi-cal compounds. The chemical composition of bio-oil renders it a very recalcitrant chemical compound. To date, the difficulties in utilizing bio-oil have limited its commercial development to the production of liq-uid smoke as food flavoring. Practitioners have at-tempted to utilize raw bio-oil as a fuel; they have also applied many techniques to upgrade bio-oil to a fuel. Attempts to utilize raw bio-oil as a combustion engine fuel have resulted in engine or turbine dam-age; however, Stirling engines have been shown to successfully combust raw bio-oil without damage. Utilization of raw bio-oil as a boiler fuel has met with more success and an ASTM standard has recently been released describing bio-oil characteristics in relation to assigned fuel grades. However, commercialization has been slow to follow and no reports of distribution of these bio-oil boiler fuels have been reported. Co-feeding raw bio-oil with coal has been successfully performed but no current power generation facilities are following this practice. Upgrading of bio-oils to hydrocarbons via hydroprocessing is being performed by several organizations. Currently, limited catalyst life is the obstacle to commercialization of this tech-nology. Researchers

  10. An Evaluation of Holistic Sustainability Assessment Framework for Palm Oil Production in Malaysia

    Directory of Open Access Journals (Sweden)

    Chye Ing Lim

    2015-12-01

    Full Text Available Palm oil based biodiesel offers an alternative energy source that can reduce current dependence on conventional fossil fuels and may reduce greenhouse gas (GHG emissions depending on the type of feedstock and processes used. In the Malaysian context, the palm oil industry not only provides high-yield, renewable feedstock to the world, it brings socio-economic development to the Malaysian rural community and contributes to the national income. However, the sustainability of palm oil remains controversial, due to deforestation, pollution and social conflicts associated with its production. Sustainability assessment is vital for the palm oil industry to identify weaknesses, improve its sustainability performance and improve consumer confidence. This paper proposes a holistic sustainability assessment framework for palm oil production with the aim to address the weaknesses of existing palm oil sustainability assessment methods. It identifies environmental, social and economic Headline Performance Indicators, Key Performance Indicators and their Performance Measures in crude palm oil production in a structured framework. Each quantitative/semi-quantitative performance measure is translated into Likert Scale of 1–5, where 3 is the threshold value, 5 is the ideal condition, and 1 is the worst case scenario. Calculation methods were established for the framework to provide quantitative assessment results. The framework was tested using a hypothetical example with data from existing studies. The results suggest that crude palm oil production in Malaysia is below the sustainability threshold. Evaluations of this sustainability assessment framework also demonstrate that it is a comprehensive assessment method for assessing sustainability of feedstock for biofuel production.

  11. Study on structure and wetting characteristic of cattail fibers as natural materials for oil sorption.

    Science.gov (United States)

    Cao, Shengbin; Dong, Ting; Xu, Guangbiao; Wang, Fumei

    2016-12-01

    Cattail fiber is considered as one of the biomasses for oil sorption purposes. In this work, the unique structure and wetting characteristic, as well as the basic mechanisms governing oil uptake of cattail fibers were investigated. Cattail fibers grow in tufts with down-like structure consisting of root, stem, seed and several fibers. A single cattail fiber was bamboo-shaped exhibiting 4-dimensional open spaces with fineness varying between 10 and 17.5 μm, average length at 7.9 ± 1.2 mm. The skeleton of the fiber consists of lignocellulose coated by a hydrophobic wax coating with 45.41% of crystallinity. The exceptional chemical, physical and microstructural properties enable the cattail fiber to be highly hydrophobic and oleophilic. The water droplets could stand on the fibers' surfaces with the contact angles more than 130°, while oil droplets disappear quickly from the fibers' surfaces within several seconds. When used as the sorbent for oil, cattail fibers were found to absorb about 12 g of oil per gram of fibers and retained over 88% of absorbed oil even after 24 h dripping. The unique structure of cattail fibers played an important role in oil sorption. The result proposed that cattail fibers are a promising natural source for the production of oil absorbents.

  12. European oil product supply modelling; Modelisation de l`offre de produits petroliers en Europe

    Energy Technology Data Exchange (ETDEWEB)

    Saint-Antonin, V

    1998-12-11

    Over the last few years, trends in European oil product consumption (in terms of level as structure and quality) has important implications of the refining industry. In this context, the purpose of this thesis consists in building a mathematical programming model applied to the European refineries in order to determine oil product supply prices, European refining industry investments and oil product exchanges of the European Union. The first part presents the reason for our choice for a long-term aggregate multi-refineries linear programming model, based on European refineries characteristics and the objectives of our model. Its dual properties are studied in detail and we focus particularly on the European exchange modelling. In the second part, an analysis of the European refining trends leads us to identify parameters and variables of the model that are essential to the aggregate representation of the European oil product supply. The third part is devoted to the use of this model, regarding two scenarios of increasingly stringent specifications for gasoline and diesel oil. Our interest for these products is due to their important share of the European oil product consumption and the not insignificant responsibility of the transport sector for atmospheric pollution. Finally, in order to have the use of an overall picture of the European refining industry, we build a regression model summarizing, though a few equations, the main relations between the major endogenous and exogenous variables o the LP model. Based on pseudo-data, this kind of model provides a simple and robust representation of the oil product supply. But a more specialized analysis of the refining industry operations, turning on a technical assessment of processing units, is reliant on the use of an optimization model such as the model we have built. (author) 102 refs.

  13. Product Structuring for Sodium Reduction.

    Science.gov (United States)

    Goh, Aaron S M

    2015-01-01

    Salt is an essential ingredient to enhance the flavour of food products. However, high salt intake has been linked to cardiovascular diseases. Methods to reduce salt in food products based on product structuring have gained increasing attention in the past few years. These methods attempt to deliver as much salt as possible from the food products to the taste buds without increasing the salt content in the products. This paper gives a brief review of the different product structuring methods that influence how the salt is released from the food matrix and/or how the salt is transported to the taste receptors.

  14. Oil migration in chocolate and almond product confectionery systems.

    Science.gov (United States)

    Altan, Aylin; Lavenson, David M; McCarthy, Michael J; McCarthy, Kathryn L

    2011-08-01

    Oil migration from high oil content almond confections into adjacent chocolate causes changes in product quality. The objective of this study was to quantify the oil migration from almond products to dark chocolate. Magnetic resonance imaging (MRI) was used to monitor spatial and temporal changes of liquid lipid content. A multislice spin echo pulse (MSSE) sequence was used to acquire images with a 7.8-ms echo time and a 1000-ms repetition time using a 1.03T Aspect AI MRI spectrometer. Samples were prepared as a 2-layer model system of chocolate and almond confection. Six different almond products and 1 type of dark chocolate were used. Samples were stored at 20, 25, and 30°C for a time frame of several months. Rate and extent of migration were quantified by a kinetic expression based on the linear dependence of oil uptake by chocolate and the square root of the time. Samples showed distinctly different rate and extent of oil migration, as evidenced by quantitative differences in the kinetic rate constants and equilibrium uptake for the different sample types. This work will be helpful to design formulations for almond and almond-based products in confections. This work will be helpful to design formulations for almond use in confections. © 2011 Institute of Food Technologists®

  15. Production of Biodiesel from Vegetable Oil Using Microware Irradiation

    Directory of Open Access Journals (Sweden)

    N. Kapilan

    2012-01-01

    Full Text Available The petroleum oil supply crisis, the increase in demand and the price eruption have led to a search for an alternative fuel of bio-origin in India. Among the alternative fuels, biodiesel is considered as a sustainable renewable alternative fuel to fossil diesel. Non-edible jatropha oil has considerable potential for the production of biodiesel in India. The production of biodiesel from jatropha oil using a conventional heating method takes more than 1h. In this work, microwave irradiation has been used as a source of heat for the transesterification reaction. A domestic microwave oven was modified and used for microwave heating of the reactants. The time taken for biodiesel production using microwave irradiation was 1 min. The fuel property analysis shows that the properties of jatropha oil biodiesel satisfy the biodiesel standards, and are close to the fossil diesel standards. From this work, it is concluded that biodiesel can be produced from vegetable oil using microwave irradiation, with a significant reduction in production time.

  16. Hazelnut oil production using pressing and supercritical CO2 extraction

    Directory of Open Access Journals (Sweden)

    Jokić Stela

    2016-01-01

    Full Text Available In the hazelnut oil production it is very important to find an appropriate method to recover the oil from kernels. The objective of this study was to evaluate the oil extraction process from hazelnuts by screw pressing followed by extraction with supercritical CO2. The effects of temperature head presses, frequency and nozzle size in pressing experiments on oil temperature and recovery were monitored. The optimal pressing condition using response surface methodology was determined. In obtained hazelnut oil the following quality parameters were determined: peroxide value 0 mmol O2/kg, free fatty acids 0.23%, insoluble impurities 0.42%, moisture content 0.045%, iodine value 91.55 g I2/100 g, saponification value 191.46 mg KOH/g and p-anisidine value 0.19. Rosemary extract was the most effective in protecting the oil from oxidative deterioration. The residual oil that remained in the cake after pressing was extracted totally with supercritical CO2 and such defatted cake, free of toxic solvents, can be used further in other processes.

  17. Recent Trends in Water Use and Production for California Oil Production.

    Science.gov (United States)

    Tiedeman, Kate; Yeh, Sonia; Scanlon, Bridget R; Teter, Jacob; Mishra, Gouri Shankar

    2016-07-19

    Recent droughts and concerns about water use for petroleum extraction renew the need to inventory water use for oil production. We quantified water volumes used and produced by conventional oil production and hydraulic fracturing (HF) in California. Despite a 25% decrease in conventional oil production from 1999 to 2012, total water use increased by 30% though much of that increase was derived from reuse of produced water. Produced water volumes increased by 50%, with increasing amounts disposed in unlined evaporation ponds or released to surface water. Overall freshwater use (constituting 1.2% of the state's nonagricultural water consumption) increased by 46% during this period due to increased freshwater-intensive tertiary oil production. HF has been practiced in California for more than 30 years, accounting for 1% of total oil production in 2012 from mostly directional and vertical wells. Water use intensity for HF wells in California averaged at 3.5 vol water/vol oil production in 2012 and 2.4 vol/vol in 2013, higher than the range from literature estimates and net water use intensity of conventional production (1.2 vol/vol in 2012). Increasing water use and disposal for oil production have important implications for water management and have potentially adverse health, environmental, and ecological impacts.

  18. Margarine and spread products with oils rich in polyunsaturated fatty acid – organogel approach

    Science.gov (United States)

    Organogels have drawn increasing interest as alternatives to trans fatty acids and saturated fatty acids-containing hardstocks used in structured food products such as margarine, spread and shortening. In this research, organogels formed by plant wax and vegetable oil were evaluated in an actual mar...

  19. Structuring edible oil with lecithin and sorbitan tri-stearate

    NARCIS (Netherlands)

    Pernetti, M.; Malssen, van K.; Kalnin, D.J.E.; Flöter, E.

    2007-01-01

    The gelation of edible oil by a mixture of lecithin and sorbitan tri-stearate (STS) was studied. The two components individually in oil do not give structure at concentrations between 6% and 20% w/w: viscous, pourable solutions are obtained. A synergetic effect is observed with their mixture, at

  20. Structuring edible oil with lecithin and sorbitan tri-stearate

    NARCIS (Netherlands)

    Pernetti, M.; Malssen, van K.; Kalnin, D.J.E.; Flöter, E.

    2007-01-01

    The gelation of edible oil by a mixture of lecithin and sorbitan tri-stearate (STS) was studied. The two components individually in oil do not give structure at concentrations between 6% and 20% w/w: viscous, pourable solutions are obtained. A synergetic effect is observed with their mixture, at spe

  1. BIOSURFACTANTS PRODUCTION BY Pseudomonas aeruginosa USING SOYBEAN OIL AS SUBSTRATE

    Directory of Open Access Journals (Sweden)

    Venty Suryanti

    2010-06-01

    Full Text Available Optimization condition of the biosurfactants production by P. aeruginosa using soybean oil as substrate has been examined. The media containing 10% v/v of the soybean oil and 6 days of the fermentation time was the optimum condition for the biosurfactants production. The extraction technique using different solvent polarity (n-hexane, chloroform, ethyl acetate and buthanol, respectively was applied for the isolation of the biosurfactants. The biosurfactant was found in the extract chloroform of the crude biospasoy (biosurfactants obtained from soybean oil as substrate which then is called chlo-biospasoy. The chlo-biospasoy was identified as rhamnolipids which had oil in water (o/w emulsion type, had the CMC of 860 mg/L and could reduced the surface tension of the water from 72 mN/m to 52 mN/m. The chlo-biospasoy could be used as an emulsifier to form emulsion between water and hydrocarbon such as palm oil, benzene, premium or toluene with various stability. The results indicated that chlo-biospasoy could be used as an emulsifying and emulsion-stabilizing agent.     Keywords: Biosurfactants, P. aeruginosa, Soybean Oil, Emulsifier

  2. Impact of Expanded North Slope of Alaska Crude Oil Production on Crude Oil Flows in the Contiguous United States

    Energy Technology Data Exchange (ETDEWEB)

    DeRosa, Sean E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Flanagan, Tatiana Paz [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-05-01

    The National Transportation Fuels Model was used to simulate a hypothetical increase in North Slope of Alaska crude oil production. The results show that the magnitude of production utilized depends in part on the ability of crude oil and refined products infrastructure in the contiguous United States to absorb and adjust to the additional supply. Decisions about expanding North Slope production can use the National Transportation Fuels Model take into account the effects on crude oil flows in the contiguous United States.

  3. Castor and jatropha oils: production strategies – A review

    Directory of Open Access Journals (Sweden)

    Lago Regina C.A.

    2009-07-01

    Full Text Available The Brazilian bioenergy matrix is based on four platforms: ethanol, energy forests, residues and co-products and biodiesel. The food-energy dichotomy in the use of edible oils is one factor which has stimulated the search for non-edible oleaginous energy crops, such as many native palms. By the year 2000 Brazil had an annual deficit of 80 thousand tons of castor oil, making necessary to import oil from China and India. After a strong debate the National Program on Biodiesel Production (NPBP was launched by December 2004. After an initial excessive enthusiasm, small producers being focused in the program, a more mature and realistic planning is undertaken. Production in semi arid lands is being stimulated, mainly castor (Ricinus communis and Jatropha (Jatropha curcas. Apart from belonging to the same botanical family (Euphorbiaceae, both plants are well resistant to poor soils. Castor plant is well adapted to practically the whole country, except for some extreme areas (too low water availability or too much rain. Castor keeps being an alternative for the semi arid region but much more technology is requested to make it largely exploited. Following the petroleum crisis of 1980’s an ambitious research program on Jatropha curcas was initiated, later on discontinued and presently retaken by Embrapa and some Universities. Progress is slower than in the case of Ricinus communis. The first agronomical observations confirmed low productivity, problems with pests and diseases, high harvesting costs etc. Some strategic factors should be considered for the production of castor and Jatropha oils: 1. Production of raw materials; 2. Production of oils; 3. Detoxification and value aggregation to the extraction cakes and residues. Regarding raw material production, it is necessary a strong, long term research program on genetic breeding (short cycle varieties, with high productivity and allowing a sole harvesting, soil fertility, pest control, domestication

  4. Environmental Compliance for Oil and Gas Exploration and Production

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, Christine

    1999-10-26

    The Appalachian/Illinois Basin Directors is a group devoted to increasing communication among the state oil and gas regulatory agencies within the Appalachian and Illinois Basin producing region. The group is comprised of representatives from the oil and gas regulatory agencies from states in the basin (Attachment A). The directors met to discuss regulatory issues common to the area, organize workshops and seminars to meet the training needs of agencies dealing with the uniqueness of their producing region and perform other business pertinent to this area of oil and gas producing states. The emphasis of the coordinated work was a wide range of topics related to environmental compliance for natural gas and oil exploration and production.

  5. Biodiesel Production from Acidified Oils via Supercritical Methanol

    Directory of Open Access Journals (Sweden)

    Jianxin Li

    2011-12-01

    Full Text Available In biodiesel production, the vegetable oil used as raw material for transesterification should be free of water and free fatty acids (FFAs, which may consume catalyst and reduce catalyst efficiency. In this work biodiesel was prepared from acidified oils (AO through a supercritical methanol route, in which the esterification of FFAs and transesterification of glyceride with methanol occurred simultaneously. The effects of the mass ratio of methanol to AO, the operation temperature as well as the water content on the FFAs conversion and glycerol yield were investigated. The results indicated that the FFAs conversion for esterification under the condition of 1:1 methanol/oil ratio, 310 °C and 15 min reaction time reached 98.7%, and the glycerol yield for transesterification under 0.25:1 methanol/oil ratio, 290 °C and 20 min reaction time reached 63.5% respectively.

  6. Oil-production policy and economic development in Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Razavi, H.

    1985-04-01

    An optimization model to analyze Mexico's oil export policy in relation to its requirements for foreign exchange and resource management prescribes an ambitious plan. The plan requires a large amount of oil export and foreign borrowing to finance domestic capital formation, which will increase national production and private consumption. When oil prices and return on foreign assets are considered, a substantially more conservative plan results. The general implication of the stochastic solution is that Mexico should follow a do less policy. The extent of this conservatism is determined by the policymakers' views on the degree of instability in the oil market as well as the unsteadiness of the foreign capital market. 7 references, 3 tables.

  7. Side-stream products of edible oil refining as feedstocks in biodiesel production

    Directory of Open Access Journals (Sweden)

    Cvetković Bojan S.

    2016-01-01

    Full Text Available Biodiesel, a diesel fuel alternative, is produced from vegetable oils and animal fats by the transesterification reaction of triacylglycerols and lower aliphatic alcohols. Beside number advantages related to fossil fuels, the main barrier to biodiesel wider commercial use is the high price of edible oils. Recently, the special attention was given to side-stream products of edible oil refining as low-cost triacylglycerol sources for biodiesel production because of their positive economic and ecological effects. In this paper, the different procedures for biodiesel production from side-stream refining products such as soapstock, spent bleaching earth and deodorizer distillate were analyzed. The main goal of this paper is to analyze the possibilities for reusing the by-products of edible oil refinement in the biodiesel production.

  8. Life Cycle Assessment (LCA) of the biofuel production process from sunflower oil, rapeseed oil and soybean oil

    Energy Technology Data Exchange (ETDEWEB)

    Sanz Requena, J.F.; Guimaraes, A.C.; Quiros Alpera, S.; Relea Gangas, E.; Hernandez-Navarro, S.; Navas Gracia, L.M.; Martin-Gil, J.; Fresneda Cuesta, H. [Universidad Europea Miguel de Cervantes, Valladolid (Spain). Dept. of Natural Resources; Valladolid Univ., Palencia (Spain). Dept. of Forest and Agricultural Engineering

    2011-02-15

    Once ratified the Kyoto protocol, Spain arises the great challenge of reducing the emissions of greenhouse gases. Among the measures proposed is the introduction of biofuels in the market, both for the transport sector and for the production of heat. This paper compares the environmental impact from the production of biofuels whose origin is the oil obtained from sunflower, rapeseed and soybeans. The environmental impact of each production is performed by applying the methodology of life cycle analysis (LCA). The categories where you get a greater impact are land use, fossil fuels, carcinogens, inorganic respiratory and climate change. The cause is mainly due to the processes of seed production. We have also found a significant impact on the drying and preparation processes of the seed as well as the crude soybean oil extracting process. Moreover as the LCA shows production of rapeseed and sunflower has a positive contribution to climate change. (author)

  9. Utilisation of vegetable oils in the production of lovastatin by Aspergillus terreus ATCC 20542 in submerged cultivation

    Directory of Open Access Journals (Sweden)

    Pattana Sripalakit

    2011-07-01

    Full Text Available The effect of vegetable oils as a supplementary carbon source during the production of lovastatin by Aspergillus terreus ATCC 20542 in submerged culture was investigated. The six vegetable oils tested were sesame oil, sunflower oil, soya bean oil, corn oil, palm oil and olive oil. Lovastatin concentration and biomass were measured. Lovastatin production was higher in several oil-containing media compared to control medium. In particular, palm oil and soya bean oil significantly improved lovastatin production. Yields with palm oil and soya bean oil were 4.5- and 1.4-fold higher respectively, compared with control. Sesame oil and corn oil, however, had a negative effect on lovastatin production. Biomass was proportional to vegetable oil concentration, but an excessive vegetable oil concentration resulted in a lower yield of lovastatin. Thus, some vegetable oils appear to be excellent adjuvants for improving efficiency of lovastatin production.

  10. Alkali-catalyzed production of biodiesel from waste frying oils

    Directory of Open Access Journals (Sweden)

    ZLATICA J. PREDOJEVIĆ

    2009-08-01

    Full Text Available The effects of the transesterification parameters on the yield and quality of the methyl esters (MEs produced from waste frying oil (WFO were investigated. A two-step alkali transesterification reaction followed by silica gel purification step was applied. The investigated reaction parameters were the methanol/oil molar ratio (6:1 and 9:1, the catalyst/oil weight ratio (1.0 and 1.5 mass % and the type of catalyst (NaOH and KOH. The physical and chemical properties of the employed feedstock and the obtained biodiesel were determined in order to investigate the effects of both the properties of the WFO and the reaction parameters on the characteristics and yields of the product. It was found that the properties of the feedstock had a determinant effect on the physical and chemical properties of the MEs, as the majority of them did not differ significantly under the studied reaction parameters. However, the reaction parameters influenced the yields of the product. Higher yields were obtained with a 1.0 than with a 1.5 mass % catalyst to oil ratio. The increasing yield with decreasing catalyst/oil ratio was more pronounced with NaOH (9.15–14.35 % than with KOH (2.84–6.45 %. When KOH was used as the catalyst, the yields were always higher (the mean yield was 94.86 % in comparison to those obtained with NaOH (the mean was 84.28 %. Furthermore, the efficiency of KOH in conversion of WFO to purified MEs in comparison to NaOH was even more pronounced in the case of the higher methanol/oil ratio, i.e., for the 9:1 methanol/oil ratio, the yield increase with KOH was about 2 times higher than the yield with NaOH, regardless of the applied catalyst/oil ratio.

  11. Indonesia palm oil production without deforestation and peat conversion by 2050

    NARCIS (Netherlands)

    Afriyanti, Dian; Kroeze, Carolien; Saad, Asmadi

    2016-01-01

    Palm oil is a promising source of cooking oil and biodiesel. The demand for palm oil has been increasing worldwide. However, concerns exist surrounding the environmental and socio-economic sustainability of palm oil production. Indonesia is a major palm oil producing country. We explored scenario

  12. Indonesia palm oil production without deforestation and peat conversion by 2050

    NARCIS (Netherlands)

    Afriyanti, Dian; Kroeze, Carolien; Saad, Asmadi

    2016-01-01

    Palm oil is a promising source of cooking oil and biodiesel. The demand for palm oil has been increasing worldwide. However, concerns exist surrounding the environmental and socio-economic sustainability of palm oil production. Indonesia is a major palm oil producing country. We explored

  13. Change and recovery of coastal mesozooplankton community structure during the Deepwater Horizon oil spill

    Science.gov (United States)

    Carassou, L.; Hernandez, F. J.; Graham, W. M.

    2014-12-01

    The response of mesozooplankton community structure to the Deepwater Horizon oil spill in the northern Gulf of Mexico was investigated using data from a long-term plankton survey off the coast of Alabama (USA). Environmental conditions observed in the study area during the oil spill (2010) were compared to historical observations (2005-2009), to support the contention that variations observed in zooplankton assemblage structure may be attributed to the oil spill, as opposed to natural climatic or environmental variations. Zooplankton assemblage structure observed during the oil spill period (May-August) in 2010 was then compared to historical observations from the same period (2005-2009). Significant variations were detected in assemblage structure in May and June 2010, but these changes were no longer significant by July 2010. The density of ostracods, cladocerans and echinoderm larvae were responsible for most of the differences observed, but patterns differed depending on taxa and months. Many taxa had higher densities during the oil spill year, including calanoid and cyclopoid copepods, ostracods, bivalve larvae and cladocerans, among others. Although this result is somewhat surprising, it is possible that increased microbial activity related to the infusion of oil carbon may have stimulated secondary production through microbial-zooplankton trophic linkages. Overall, results suggest that, although changes in zooplankton community composition were observed during the oil spill, variations were weak and recovery was rapid.

  14. Modeling and optimization for oil well production scheduling☆

    Institute of Scientific and Technical Information of China (English)

    Jin Lang; Jiao Zhao

    2016-01-01

    In this paper, an oil wel production scheduling problem for the light load oil wel during petroleum field exploi-tation was studied. The oil well production scheduling was to determine the turn on/off status and oil flow rates of the wel s in a given oil reservoir, subject to a number of constraints such as minimum up/down time limits and well grouping. The problem was formulated as a mixed integer nonlinear programming model that minimized the total production operating cost and start-up cost. Due to the NP-hardness of the problem, an improved par-ticle swarm optimization (PSO) algorithm with a new velocity updating formula was developed to solve the problem approximately. Computational experiments on randomly generated instances were carried out to eval-uate the performance of the model and the algorithm's effectiveness. Compared with the commercial solver CPLEX, the improved PSO can obtain high-quality schedules within a much shorter running time for all the instances.

  15. Carbonyl Emissions From Oil and Gas Production Facilities

    Science.gov (United States)

    Lyman, S. N.; O'Neil, T.; Tran, T.

    2015-12-01

    A number of recent studies have targeted emissions of methane and other hydrocarbons from oil and gas exploration and production activity. These measurements are greatly increasing understanding of the atmospheric impacts of oil and gas development. Very few measurements exist, however, of emissions of formaldehyde and other carbonyls from oil and gas equipment. Carbonyls are toxic and serve as important ozone precursors, especially during winter ozone episodes in places like Utah's Uintah Basin. Current air quality models are only able to reproduce observed high wintertime ozone if they incorporate emissions inventories with very high carbonyl emissions. We measured carbonyl emissions from oil and gas equipment and facilities—including glycol dehydrators, liquid storage tanks, raw gas leaks, raw gas-burning engines, and produced water surface impoundments—in Rocky Mountain oil and gas fields. Carbonyl emissions from raw gas were below detection, but emissions of formaldehyde, acetaldehyde, and other carbonyls were detected from liquid storage tanks, glycol dehydrators, and other oil and gas equipment. In some cases, carbonyls may be formed from the degradation of methanol and other chemicals used in oil and gas production, but the collected data provide evidence for other non-combustion formation pathways. Raw gas-burning engines also emitted carbonyls. Emissions from all measured sources were a small fraction of total volatile organic compound emissions. We incorporated our measurements into an emissions inventory, used that inventory in an air quality model (WRF-SMOKE-CAMx), and were unable to reproduce observed high wintertime ozone. This could be because (1) emission sources we have not yet measured, including compressors, gas processing plants, and others, are large; (2) non-carbonyl emissions, especially those that quickly degrade into carbonyls during photochemical processing, are underestimated in the inventory; or (3) the air quality model is unable

  16. Protocol for testing bioremediation products against weathered Alaskan crude oil

    Energy Technology Data Exchange (ETDEWEB)

    Venosa, A.D.; Haines, J.R.; Nisamaneepong, W.; Govind, R.; Pradhan, S.

    1990-01-01

    In the summer of 1989, EPA and Exxon Corp. conducted a joint field study to determine if natural biodegradation of the Prudoe Bay crude oil spilled from the Exxon Valdez could be accelerated by application of oleophilic and water soluble fertilizers. Numerous private firms have since submitted proposals to have their microbial products tested for bioremediation enhancement. EPA commissioned the National Environmental Technology Applications Corporation (NETAC) to coordinate an effort to select and test commercial products for efficacy against Alaskan crude oil. A panel of experts was assembled to review the proposals, and nine products were selected for the first tier of testing. The experiments were conducted at the Risk Reduction Engineering Laboratory in Cincinnati. Three lines of evidence were used to select the final products for further testing: cumalative oxygen uptake via electrolytic respirometry, microbial growth, and compositional analysis of treated oil by GC and GC/MS. The commercial products were compared against oleophilic and inorganic fertilizers in a comprehensive protocol incorporating sterile and non-sterile controls. Respirometric vessels and shaker flask microcosms were set up for the comparative testing using weathered oil and natural seawater from Prince William Sound. The paper presents the protocol, the test results, and conclusions derived from the study.

  17. Production of biodiesel from vegetable oils

    Directory of Open Access Journals (Sweden)

    Luque, Susana

    2008-03-01

    Full Text Available Biodiesel is produced by transesterification of triglycerides present in animal fat or vegetable oils, by displacing glycerine with a low molar mass alcohol. This resulting ester mixture has physico-chemical properties similar to those of petroleum diesel. This paper reviews the synthetic paths that lead to biodiesel by means of the catalytic transesterification of vegetable oils. Although methyl esters are at present the only ones produced at industrial scale, the use of ethanol, which can also be obtained from renewable resources, has been considered, since it would generate a cleaner and more biocompatible fuel.El biodiésel se produce mediante la transesterificación de triglicéridos, presentes en grasas animales o aceites vegetales, en un proceso en el que un alcohol de bajo peso molecular desplaza a la glicerina. La mezcla de esteres así resultante posee unas propiedades físico-químicas similares a las del diésel procedente de petróleo. En este artículo se revisan las vías de síntesis de biodiésel mediante la transesterificación catalítica de aceites vegetales. Aunque actualmente a escala industrial solo se producen ésteres metílicos, también se ha considerado el uso de etanol, ya que éste se obtiene también de fuentes renovables, generando así un combustible más limpio y biocompatible.

  18. Lipase production by Penicillium restrictum using solid waste of industrial babassu oil production as substrate.

    Science.gov (United States)

    Palma, M B; Pinto, A L; Gombert, A K; Seitz, K H; Kivatinitz, S C; Castilho, L R; Freire, D M

    2000-01-01

    Lipase, protease, and amylase production by Penicillium restrictum in solid-state fermentation was investigated. The basal medium was an industrial waste of babassu oil (Orbignya oleifera) production. It was enriched with peptone, olive oil, and Tween-80. The supplementation positively influenced both enzyme production and fungal growth. Media enriched with Tween-80 provided the highest protease activity (8.6 U/g), whereas those enriched with peptone and olive oil led to the highest lipase (27.8 U/g) and amylase (31.8 U/g) activities, respectively.

  19. Characterization of residual oils for biodiesel production

    Directory of Open Access Journals (Sweden)

    Edmilson Antonio Canesin

    2014-01-01

    Conclusions: The obtained results suggesting that it is possible to take advantage of these residues for biodiesel production as the obtained products were approved according to the rules established by the National Association of Petroleum (ANP; the bovine samples were the exception regarding moisture and acidity.

  20. Legal Regulation Of Oil Production In Mexico

    Directory of Open Access Journals (Sweden)

    Pavel A. Byshkov

    2015-06-01

    Full Text Available In the article sources of legal regulation of production and public administration in the sphere of production of mineral energy resources by the legislation of Mexico are considered. Standards of the international legal acts, the Constitution of Mexico and the special industry legislation in the sphere of use of mineral resources are investigated.

  1. The research and practice of boosting oil production by duplicated horizontal wells in thick super heavy oil reservoir

    Energy Technology Data Exchange (ETDEWEB)

    Peiwu, Li; Yang Jing, Wangping; Ping, Yuan [Exploration and Development Research Institute of Liaohe Oilfield Company, PetroChina, P.R.China , 124010 (China)

    2011-07-01

    In the oil industry, the extraction of heavy oil and super heavy oil from reservoirs is difficult and production decline and sand production are some of the numerous challenges it faces. The aim of this paper is to show how secondary development can address these issues. A preliminary study was conducted and then a plan of secondary development was applied to M6 Block which is a massive extra-ultra heavy oil reservoir. The plan included 154 wells with 30 new horizontal wells. Results proved SAGD to be a good technique for high oil recovery results with improved production from M6 Block. After the implementation of the secondary development, oil recovery improved by 36.3%. This technique also solved the sand production problem. This study showed that secondary development can be a solution to obtain a better performance from heavy oil reservoirs and provides guidance to other similar reservoir.

  2. In-vitro activity of essential oils, in particular Melaleuca alternifolia (tea tree) oil and tea tree oil products, against Candida spp.

    Science.gov (United States)

    Hammer, K A; Carson, C F; Riley, T V

    1998-11-01

    The in-vitro activity of a range of essential oils, including tea tree oil, against the yeast candida was examined. Of the 24 essential oils tested by the agar dilution method against Candida albicans ATCC 10231, three did not inhibit C. albicans at the highest concentration tested, which was 2.0% (v/v) oil. Sandalwood oil had the lowest MIC, inhibiting C. albicans at 0.06%. Melaleuca alternifolia (tea tree) oil was investigated for activity against 81 C. albicans isolates and 33 non-albicans Candida isolates. By the broth microdilution method, the minimum concentration of oil inhibiting 90% of isolates for both C. albicans and non-albicans Candida species was 0.25% (v/v). The minimum concentration of oil killing 90% of isolates was 0.25% for C. albicans and 0.5% for non-albicans Candida species. Fifty-seven Candida isolates were tested for sensitivity to tea tree oil by the agar dilution method; the minimum concentration of oil inhibiting 90% of isolates was 0.5%. Tests on three intra-vaginal tea tree oil products showed these products to have MICs and minimum fungicidal concentrations comparable to those of non-formulated tea tree oil, indicating that the tea tree oil contained in these products has retained its anticandidal activity. These data indicate that some essential oils are active against Candida spp., suggesting that they may be useful in the topical treatment of superficial candida infections.

  3. Transesterification of coconut oil for FAME production using ultrasound

    Science.gov (United States)

    Supriadi, Eko; Marlinda, Lenny; Prajitno, Danawati Hari; Mahfud, Mahfud

    2017-05-01

    To overcome energy crisis, the vegetable oils-derived biofuel can be chosen as an alternative to petroleum-based diesel. The transesterification of coconut oil in methanol with K/γ-Al2O3 catalyst using ultrasound-assisted to produce fatty acid methyl ester (FAME) as one of type biofuel was studied. The reaction occurred in batch reactor at a 9 : 1 molar ratio of methanol to coconut oil. The following reaction conditions were used in the catalytic test : concentration of catalyst to oil of 0.5, 1.0, 1.5, 2.0, and 2.5%, the reaction time of 10, 20, 30, 60, 90, 120, and 150 s, and the frequency ultrasonication of 20 and 40 KHz. At first, the preparation of K/γ-Al2O3 catalyst was done and followed by transesterification process. After reaction, the phase separation and purification from impurities were done. Finally, FAME was analized based on this parameters, i.e., yield, density, viscosity, and flash point. FAME yield of 93.76% was obtained at the frequency ultrasonication of 40 kHz with K/γ-Al2O3 catalyst concentration to oil of 2.5 wt.% for 150 s. It's the best conditions for FAME production by transesterification of coconut oil using ultrasound-assisted.

  4. OIL SLUGS FOR PRODUCTION OF PISTON RING

    Directory of Open Access Journals (Sweden)

    V. F. Bevza

    2008-01-01

    Full Text Available The developed technological process of continuously cyclic casting by frosting allows to receive high-quality hollow cylindrical slugs of cast iron for production of critical parts. 

  5. Moringa oleifera oil: Studies of characterization and biodiesel production

    Energy Technology Data Exchange (ETDEWEB)

    da Silva, Jhosianna P.V.; Serra, Tatiana M.; Meneghetti, Simoni M.P. [Universidade Federal de Alagoas, Instituto de Quimica e Biotecnologia, Laboratorio de Oleoquimica, Maceio, Alagoas, CEP 57072-970 (Brazil); Gossmann, Marcelo; Wolf, Carlos R.; Meneghetti, Mario R. [Universidade Luterana do Brasil, Instituto de Quimica, Canoas, Rio Grande do Sul, CEP 92420-280 (Brazil)

    2010-10-15

    This work describes studies with the seeds of Moringa oleifera (MO), obtained in the northeast of Brazil, evaluating some properties and chemical composition of the oil, as well any potential application in biodiesel production. The studied physicochemical properties of the MO biodiesel, suggest that this material may be used as fuel in diesel engines, mainly as a mixture to petrodiesel. (author)

  6. Awkward Prices of Oil Products and Disputed Subsidy

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ Prices of oil products continue to rise on one hand;profits of refineries climb repeatedly on the other hand In 2006, Sinopec Corp. posted an excellent fiscal report with a profit of RMB50.6 billion. Yet Wang Tianpu, CEO of Sinopec Corp.

  7. Integrating Sunflower Oil Seed Crops into Florida Horticultural Production Systems

    Science.gov (United States)

    Locally produced biodiesel feedstock plant oil creates a unique possibility to integrate multiple-goal oriented cover crops into Florida horticultural production systems. Typically, cover crops are planted to improve soil fertility and the natural suppression of soilborne pests at times when fields...

  8. Biodiesel production from microalgae oil catalyzed by a recombinant lipase.

    Science.gov (United States)

    Huang, Jinjin; Xia, Ji; Jiang, Wei; Li, Ying; Li, Jilun

    2015-03-01

    A recombinant Rhizomucor miehei lipase was constructed and expressed in Pichia pastoris. The target enzyme was termed Lipase GH2 and it can be used as a free enzyme for catalytic conversion of microalgae oil mixed with methanol or ethanol for biodiesel production in an n-hexane solvent system. Conversion rates of two major types of biodiesel, fatty acid methyl ester (FAME) and fatty acid ethyl ester (FAEE), reached maximal values (>90%) after 24h. The process of FAME production is generally more simple and economical than that of FAEE production, even though the two processes show similar conversion rates. In spite of the damaging effect of ethanol on enzyme activity, we successfully obtained ethyl ester by the enzymatic method. Our findings indicate that Lipase GH2 is a useful catalyst for conversion of microalgae oil to FAME or FAEE, and this system provides efficiency and reduced costs in biodiesel production.

  9. CHARACTERISTICS OF SPILLED OILS, FUELS, AND PETROLEUM PRODUCTS: 1. COMPOSITION AND PROPERTIES OF SELECTED OILS

    Science.gov (United States)

    Multicomponent composition and corresponding physical properties data of crude oils and petroleum products are needed as input to environmental fate simulations. Complete sets of such data, however, are not available in the literature due to the complexity and expense of making t...

  10. Review of Slug Detection, Modeling and Control Techniques for Offshore Oil & Gas Production Processes

    DEFF Research Database (Denmark)

    Pedersen, Simon; Løhndorf, Petar Durdevic; Yang, Zhenyu

    2015-01-01

    The current offshore oil & gas multi-phase production and transportation installations have big challenges related with the slugging flow: An unstable multi-phase flow regime where the flow rates, pressures and temperatures oscillate in the considered processes. Slug can be caused by different...... of these methods can simultaneously reduce the oil & gas production, which is a very big concern as the production rate is the key evaluation parameter for offshore production. We conclude that the slugging flow is a well-defined phenomenon, even though this subject has been extensively investigated in the past...... operating conditions and installation structures. The most severe slugs are often induced in long vertical risers or production wells, where liquid blocks gas at the riser/well base and correspondingly it causes the pressure to accumulate and hence originates the oscillating performance. There are many...

  11. Biodiesel production by chemical or enzymatic esterification of sunflower oil

    Energy Technology Data Exchange (ETDEWEB)

    Passarinho, Paula C.; Rosa, M. Fernanda; Oliveira, A.C.; Pingarilho, M.S.; Beirao, S.G.; Vieira, Ana Maria Soares

    1998-07-01

    In this work, two processes of sunflower oil transesterification, with methanol or ethanol, were studied for biodiesel production: chemical (catalyst- NaOH) and enzymatic (catalyst - rhizomucor miehei lipase). The chemical catalysis proved to be more efficient, having been obtained higher conversion yields and a better quality biodiesel, mainly in the case where methanol was used. The transesterification product had, in all cases, to be purified in order to be used as a diesel substitute.

  12. OPEC and non-OPEC oil production and the global economy

    OpenAIRE

    Ronald A. Ratti; Vespignani, Joaquin L.

    2014-01-01

    Hamilton identifies 1973 to 1996 as “the age of OPEC” and 1997 to the present as “a new industrial age.” During 1974-1996 growth in non-OPEC oil production Granger causes growth in OPEC oil production. OPEC oil production decreases significantly with positive shocks to non-OPEC oil production in the earlier period, but does not do so in the “new industrial age”. In the “new industrial age” OPEC oil production rises significantly with an increase in oil prices, unlike during “the age of OPEC” ...

  13. Structure- and oil type-based efficacy of emulsion adjuvants.

    Science.gov (United States)

    Jansen, Theo; Hofmans, Marij P M; Theelen, Marc J G; Manders, Frans; Schijns, Virgil E J C

    2006-06-29

    Oil-based emulsions are well-known immunopotentiators for inactivated, "killed" vaccines. We addressed the relationship between emulsion structure and levels of in vivo antibody formation to inactivated New Castle Disease virus (NDV) and Infectious Bronchitis virus (IBV) as antigens in 3-week-old chickens. The use of a polymeric emulsifier allowed for direct comparison of three types of emulsions, water-in-oil (W/O), oil-in-water (O/W) and W/O-in-water (W/O/W), while maintaining an identical content of components for each vehicle. They were prepared with either non-metabolizable, mineral oil or metabolizable, Miglyol 840. In addition, we assessed the inherent release capacity of each emulsion variant in vitro. Remarkably, we noted that W/O-type emulsions induced the best immune responses, while they released no antigen during 3 weeks. In general, mineral oil vaccines showed superior efficacy compared to Miglyol 840-based vaccines.

  14. Ultrasound Assisted Esterification of Rubber Seed Oil for Biodiesel Production

    Directory of Open Access Journals (Sweden)

    Berkah Fajar Tamtomo Kiono

    2012-02-01

    Full Text Available roduction of biodiesel is currently shifting from the first to the second generation in which the raw materials are mostly from non-edible type oils and fats. Biodiesel production is commonly conducted under batch operation using mechanical agitation to accelerate mass transfers. The main drawback of oil esterification is the high content of free fatty acids (FFA which may reduce the yield of biodiesel and prolong the production time (2-5 hours. Ultrasonification has been used in many applications such as component extraction due to its ability to produce cavitation under certain frequency. This research is aimed to facilitate ultrasound system for improving biodiesel production process particularly rubber seed oil. An ultrasound unit was used under constant temperature (40oC and frequency of 40 Hz. The result showed that ultrasound can reduces the processing time and increases the biodiesel yield significantly. A model to describe correlation of yield and its independent variables is yield (Y = 43,4894 – 0,6926 X1 + 1,1807 X2 – 7,1042 X3 + 2,6451 X1X2 – 1,6557 X1X3 + 5,7586 X2X3 - 10,5145 X1X2X3, where X1 is mesh sizes, X2 ratio oil: methanol and X3 type of catalyst.

  15. Catalytic production of biodiesel from soy-bean oil, used frying oil and tallow

    Energy Technology Data Exchange (ETDEWEB)

    Alcantara, R.; Amores, J.; Canoira, L.; Fidalgo, E.; Franco, M.J.; Navarro, A. [Polytechnic University of Madrid (Spain). Dept. of Chemical Engineering and Fuels

    2000-07-01

    Three fatty materials, soy-bean oil, used frying oil and tallow, were transformed into two different types of biodiesel, by transesterification and amidation reactions with methanol and diethylamine respectively. The ignition properties of these types of biodiesel were evaluated calculating the cetane index of the transesterification products, and the blending cetane number of the amide biodiesel blended with conventional diesel. Amide biodiesel enhances the ignition properties of the petrochemical diesel fuel, and it could account for the 5% market share that should be secured to biofuels by 2005. (author)

  16. Energy Requirement of Extra Virgin Olive Oil Production

    Directory of Open Access Journals (Sweden)

    Giulio Mario Cappelletti

    2014-08-01

    Full Text Available The scope of this chapter is to calculate the net energy of the production chain for virgin olive oil. Therefore, the determination was carried out for the direct and indirect energy inputs and the energy present as feedstock in the outputs (products and by-products. To perform this analysis, all of the production processes for olives and for oil extraction were studied. For the agricultural phase, three systems of cultivation were taken into consideration: the centenary olive grove (COO, the “intensive” olive grove (HDO and, the more recently introduced, “super-intensive” olive grove (HSDO. The last two models are distinguished by the high number of trees per hectare and by an intense mechanization of agricultural practices. Regarding the oil extraction phase, four different technologies were compared: the pressure system (PS, the two-phase system (2PS, the three-phase (3PS, and the system, called “de-pitted”, which provides for the separation of the pits before the oil is extracted (DPS. The analysis showed that the production of olives needs more than 90% of energy requirements, much of which is met by non-renewable sources of energy. The production of fertilizers, and also irrigation, are the production factors that require a considerable amount of energy. Among the three agricultural systems analyzed, the COO system of cultivation is the one that requires less energy as compared to the other systems. The scenario that enables the most energy return, however, is the SHDO system of cultivation, due to the greater amount of pruning residues that can be obtained.

  17. Case Studies of Water Shut-Off Treatments in Oil and Gas Production Wells

    National Research Council Canada - National Science Library

    Sławomir Falkowicz; Stanisław Dubiel; Renata Cicha-Szot

    2012-01-01

      Case Studies of Water Shut-Off Treatments in Oil and Gas Production Wells In this study some of the experimental results of water shut-off treatments in oil and gas production wells were presented...

  18. Influence of alcohol: oil molar ratio on the production of ethyl esters ...

    African Journals Online (AJOL)

    Influence of alcohol: oil molar ratio on the production of ethyl esters by enzymatic transesterification of canola oil. ... cosolvent-free reaction system with ethanol addition in three steps showed great potential for ester production. ... Article Metrics.

  19. Biodiesel Production from Bulk Frying Oil with Ultrasound Assisted

    Directory of Open Access Journals (Sweden)

    Widayat

    2013-07-01

    Full Text Available The objective of this research is to optimize of biodiesel production with ultrasound assisted. Optimization was used central composite design methods. Biodiesel was produced from frying oil with KOH catalyst and ultrasonic assisted. The variables were investigated temperature, catalyst concentration and ratio of methanol to oil. Biodiesel was separated from reactant and impurities with decantation process and distillation process. The results of research obtained optimum conversion 85.95% in operation condition are methanol/oil 5.05:1, catalyst concentration 1.65% and temperature reaction 50°C. Mathematic modeling for describe in this process like expressed; Y = 86.2107 - 7.4287X1 + 1.0661X2 + 0.6289X3 - 2.5319X12 - 2.0603X22 - 1.0618X32.

  20. Recycling of waste engine oil for diesel production.

    Science.gov (United States)

    Maceiras, R; Alfonsín, V; Morales, F J

    2017-02-01

    The aim of this work was to recycle waste engine oil until converting it into reusable product, diesel fuel. The waste oil was treated using pyrolytic distillation. The effect of two additives (sodium hydroxide and sodium carbonate) in the purification of the obtained fuel was also studied. Moreover, the influence of the number of distillations were analysed. Some thermal and physicochemical properties (density, viscosity, colour, turbidity, acidity value, distillation curves, cetane number, corrosiveness to Cu, water content, flash point and hydrocarbons) were determined to analyse the quality of the obtained fuel. The best results were obtained with 2% of sodium carbonate and two successive distillations. The obtained results showed that pyrolytic distillation of waste engine oil is an excellent way to produce diesel fuel to be used in engines.

  1. Prospects for using methods to increase oil production

    Energy Technology Data Exchange (ETDEWEB)

    Toth, B.; Voll, L.

    1985-01-01

    Due to the increase in demand and the unbalancing of the oil market, the introduction in the early 1970s into oil field practice of methods for more effective development became justified from an economic standpoint as well. However, the cited methods did not become as common as expected and their commercial use on a worldwide scale is unresolved, as before. Methods for increasing oil production of strata are analyzed, the basic criteria for their suitability are presented and the factors which limit their expansion are examined. Experience acquired in the United States as a result of commercial experiments on methods for thermal and chemical development and development by pumping gas is cited. It is shown that the cited methods may be effective even in conditions which are different from the general cases. Attention is directed to the economic effects from the use of new methods and the expected trends in the development of them both in Hungary and abroad are outlined.

  2. PEARL RIVER DELTA OIL PRODUCTS PIPELINE ENTERS SHENZHEN

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ With the strong support of Shenzhen, Huizhou Municipal governments and Shenzhen Petroleum Subsidiary Company, the construction of Shenzhen (Huizhou) section of Pearl River Delta oil products pipeline was started ahead of schedule on Sep.30, 2004,and coordination work for most of Shenzhen section has been completed up to the end of April this year.Presently, the construction of Shenzhen section is carried out smoothly in general, for the pipeline route, 69km for pileline pruging, 60km for pipe laying, 57.7km for welding; for process stations, the removal of Mawan oil storage has been completed by the plan, and the foundation for Dapengwan oil storage tank is under construction.

  3. Modelling demand for crude oil products in Spain

    Energy Technology Data Exchange (ETDEWEB)

    Pedregal, D.J. [Escuela Tecnica Superior de Ingenieros Industriales and Instituto de Matematica Aplicada a la Ciencia y la Ingenieria (IMACI), Universidad de Castilla-La Mancha (UCLM), Avenida Camilo Jose Cela s/n, 13071 Ciudad Real (Spain); Dejuan, O.; Gomez, N.; Tobarra, M.A. [Facultad de Ciencias Economicas y Empresariales, Universidad de Castilla-La Mancha (UCLM) (Spain)

    2009-11-15

    This paper develops an econometric model for the five most important crude oil products demand in Spain. The aim is the estimation of a range of elasticities of such demands that would serve as the basis for an applied general equilibrium model used for forecasting energy demand in a broader framework. The main distinctive features of the system with respect to previous literature are (1) it takes advantage of monthly information coming from very different information sources and (2) multivariate unobserved components (UC) models are implemented allowing for a separate analysis of long- and short-run relations. UC models decompose time series into a number of unobserved though economic meaningful components mainly trend, seasonal and irregular. A module is added to such structure to take into account the influence of exogenous variables necessary to compute price, cross and income elasticities. Since all models implemented are multivariate in nature, the demand components are allowed to interact among them through the system noises (similar to a seemingly unrelated equations model). The results show unambiguously that the main factor driving demand is real income with prices having little impact on energy consumption. (author)

  4. Microbial oils as food additives: recent approaches for improving microbial oil production and its polyunsaturated fatty acid content.

    Science.gov (United States)

    Bellou, Stamatia; Triantaphyllidou, Irene-Eva; Aggeli, Dimitra; Elazzazy, Ahmed Mohammed; Baeshen, Mohammed Nabih; Aggelis, George

    2016-02-01

    In this short review, we summarize the latest research in the production of polyunsaturated microbial oils that are of interest in food technology. The current research targets the productivity of oleaginous microorganisms, as well as the biosynthesis of particular polyunsaturated fatty acids (PUFAs). The most important efforts target the efficiency of the oleaginous machinery, via overexpression of key-enzymes involved in lipid biosynthesis, as well as the minimization of lipid degradation, by repressing genes involved in the β-oxidation pathway. The production of specific PUFAs is approached by homologous or heterologous expression of specific desaturases and elongases involved in PUFA biosynthesis in oleaginous microorganisms. New perspectives, such as the production of triacylglycerols of specific structure and the employment of adaptive experimental evolution for creating robust oleaginous strains able to produce PUFAs are also discussed.

  5. Structuring as a Basis for Product Modelling

    DEFF Research Database (Denmark)

    Mortensen, Niels Henrik; Hansen, Claus Thorp

    1999-01-01

    Structure means the way which things are built up. A composite product does not exhibit one structure, but hides in its structure of parts several different structuring principles, which fit the production, service, transport etc. Structuring of product models is complex where many factors...... are influencing. This paper identifies four factors that are influencing the structure of a product model: genetics, functionality/property, product life and product assortment. Three principles, which support determination of product model structures, are proposed....

  6. Water footprints of products of oil palm plantations and palm oil mills in Thailand.

    Science.gov (United States)

    Suttayakul, Phetrada; H-Kittikun, Aran; Suksaroj, Chaisri; Mungkalasiri, Jitti; Wisansuwannakorn, Ruthairat; Musikavong, Charongpun

    2016-01-15

    The water footprint (WF) of fresh fruit bunches (FFBs) from oil palm plantations and crude palm oil (CPO) from palm oil mills in southern and eastern Thailand were determined over 25 years. Climatic conditions, soil characteristics, and the characteristics of oil palm growth were considered. The WF of FFBs was 1063 m(3)/ton (t) on average. Green, blue, and grey waters comprised of 68, 18, and 14% of total WF, respectively. The oil palm plantations in Thailand required smaller amounts of indirect blue water. The average WF for producing a ton of CPO of seven mills was 5083 m(3). Most of the waters used in the mills originated from indirect green, blue and grey waters from the plantations. The direct blue water used in the mills had less impact on the total WF, lower than 1% of the total WF. Average percentages of green, blue, and grey waters of 69, 16, and 15% of total WF were determined for the mills, respectively. The water deprivation of the FFBs and CPO ranged from 0.73-12.9 and 3.44-58.3 m(3)H2Oeq/t, respectively. In 2013, the CPO production in Thailand including green, blue, and grey waters from plantation and blue water from mills required 11,343 million m(3) water. If the oil palm variety Suratthani 7 is used in the plantation, it would increase the yield from 15.2 to 22.8 t FFBs/ha-year and decrease the WF to 888 m(3)/t FFBs. The average value of the oil extraction rate (OER) of mills was 18.1%. With an increase in the OER of 1%, a reduction of the WF of 250 m(3)/t CPO or 5.1% of total WF could be obtained.

  7. The Spanish distribution system for oil products: an obstacle to competition?

    Energy Technology Data Exchange (ETDEWEB)

    Contin, I. [Universidad Publica de Navarra (Spain). Dpto. Gestion de Empresas; University of Njimegen (Netherlands). International Political Economy Centre; Correlje, A. [University of Rotterdam (Netherlands). Dept. of General Economy; Huerta, E. [Universidad Publica de Navarra (Spain). Dpto. Gestion de Empresas

    2001-01-01

    This paper examines why the formal liberalization of the Spanish market for automotive fuels did not introduce competition in the sector. Against the background of the transformation of the country's oil industry, it is shown how the Spanish distribution system emerged as the essential facility within the formally liberalized oil products market. 'Light-handed' regulation, in combination with the prevailing ownership structure turned the system into an impediment to newcomers' activities and to competition. This suggests that an evaluation of regulatory options for distribution systems in specific markets should take into due account crucial market characteristics like concentration and specific ownership/control relationships. (author)

  8. The Strategic Implications for U.S. - Persian Gulf Relations on Domestic and Worldwide Oil Production for Future U.S. Oil Demand.

    Science.gov (United States)

    1987-03-01

    46 X. U.S. Reserves of Crude Oil and Natural Gas Liquids ....... ................... .. 76 XI. Cuulative Crude Oil Production of...Military Oil Demand ....... .................. 54 9. Decline in Oil Price 1930 - 1931 ......... .. 69 10. U.S. Crude Oil Production (1919-1986...lists the cumulative crude oil production for 16 nations. The key question remaining, then, is taking into account the indicated and inferred reserves

  9. Production of rapeseed oil fuel in decentralized oil extraction plants. Handbook. 2. new rev. and enl. ed.; Herstellung von Rapsoelkraftstoff in dezentralen Oelgewinnungsanlagen. Handbuch

    Energy Technology Data Exchange (ETDEWEB)

    Remmele, Edgar [Technologie- und Foerderzentrum (TFZ) im Kompetenzzentrum fuer Nachwachsende Rohstoffe, Straubing (Germany)

    2009-11-15

    Increasing oil prices, the dependence on petroleum imports and the desire to reduce the CO{sub 2} emissions, are arguments to accelerate the production and utilization of biofuels. In 2007, 3.3 million tons of biodiesel and 772,000 tons of vegetable oil were used as fuel. The technically and economically successful production of rapeseed oil fuel in decentralized oil mills requires a quality assurance. Specifically, the brochure under consideration reports on the following: (1) Oilseed processing; (2) Centralized oil production in Germany; (3) Design of a decentralized oil mill; (4) Production of rapeseed oil fuel in decentralized systems; (5) Quality assurance for rapeseed oil fuel in decentralized oil mills; (6) Properties of rapeseed oil fuel; (7) Quality of rapeseed oil fuel from decentralized oil mills; (8) Economic aspects of decentralized oil extraction; (9) Legal framework conditions.

  10. Utilization of palm oil sludge through pyrolysis for bio-oil and bio-char production.

    Science.gov (United States)

    Thangalazhy-Gopakumar, Suchithra; Al-Nadheri, Wail Mohammed Ahmed; Jegarajan, Dinesh; Sahu, J N; Mubarak, N M; Nizamuddin, S

    2015-02-01

    In this study, pyrolysis technique was utilized for converting palm oil sludge to value added materials: bio-oil (liquid fuel) and bio-char (soil amendment). The bio-oil yield obtained was 27.4±1.7 wt.% having a heating value of 22.2±3.7 MJ/kg and a negligible ash content of 0.23±0.01 wt.%. The pH of bio-oil was in alkaline region. The bio-char yielded 49.9±0.3 wt.%, which was further investigated for sorption efficiency by adsorbing metal (Cd(2+) ions) from water. The removal efficiency of Cd(2+) was 89.4±2%, which was almost similar to the removal efficiency of a commercial activated carbon. The adsorption isotherm was well described by Langmuir model. Therefore, pyrolysis is proved as an efficient tool for palm oil sludge management, where the waste was converted into valuable products.

  11. Oxidative stability of structured lipids produced from sunflower oil and caprylic acid

    DEFF Research Database (Denmark)

    Timm Heinrich, Maike; Xu, Xuebing; Nielsen, Nina Skall

    2003-01-01

    and differences in production/purification, which caused lower tocopherol content and higher initial levels of primary and secondary oxidation products in SL compared with RL and SO. Grindox 117 and gallic acid did not exert a distinct antioxidative effect in the SL oil samples during storage......Traditional sunflower oil (SO), randomized lipid (RL) and specific structured lipid (SL), both produced from SO and tricaprylin/caprylic acid, respectively, were stored for up to 12 wk to compare their oxidative stabilities by chemical and sensory analyses. Furthermore, the effect of adding...

  12. Production of light oil by injection of hot inert gas

    Science.gov (United States)

    Ruidas, Bidhan C.; Ganguly, Somenath

    2016-05-01

    Hot inert gas, when injected into an oil reservoir is capable of generating a vaporization-condensation drive and as a consequence, a preferential movement of the lighter components to the production well. This form of displacement is an important unit mechanism in hot flue-gas injection, or in thermal recovery from a watered-out oil reservoir. This article presents the movement of heat front vis-à-vis the changes in the saturation profile, and the gas-phase composition. The plateau in the temperature profile due to the exchange of latent heat, and the formation of water bank at the downstream are elaborated. The broadening of the vaporization-condensation zone with continued progression is discussed. The effect of inert gas temperature on the cumulative production of oil is reviewed. The results provide insight to the vaporization-condensation drive as a stand-alone mechanism. The paper underscores the relative importance of this mechanism, when operated in tandem with other processes in improved oil recovery and CO2 sequestration.

  13. LANL PDMLink Product Structure Implementation

    Energy Technology Data Exchange (ETDEWEB)

    Scully, Christopher J. [Los Alamos National Laboratory

    2012-08-29

    Over the past 2 and a half years LANL has done both functionality exploration as well as production implementations of PDMLink Product Structure to control the configuration of many of the LANL Design Agency Products. Based on this experience LANL has been recommending for over a year that future product structure implementation in PDMLink do not use the two digit suffix in the number field of enterprise parts (or WTParts). The suffix will be part of one of the attributes for Part Number. Per the TBP's the two digit suffix represents a change in form, fit, or function in a part or a change in the production agency or a number of other conditions. It also denotes backward compatibility with earlier suffixed parts (see TBP 402 section 3.1).

  14. 78 FR 59632 - Oil and Gas and Sulphur Operations on the Outer Continental Shelf-Oil and Gas Production Safety...

    Science.gov (United States)

    2013-09-27

    ... proposed rulemaking on production safety systems on August 22, 2013 (78 FR 52240). The proposed rule would... Bureau of Safety and Environmental Enforcement 30 CFR Part 250 RIN 1014-AA10 Oil and Gas and Sulphur Operations on the Outer Continental Shelf--Oil and Gas Production Safety Systems AGENCY: Bureau of Safety...

  15. Production of methyl ester from oil in the wastewater pond of a palm oil factory

    Directory of Open Access Journals (Sweden)

    Tongurai, C.

    2007-11-01

    Full Text Available This research studied the suitable technique for the production of methyl ester from waste palm oil in the water pond of a palm oil mill. The composition of the waste palm oil was 73.82% fatty acid, 5.07% triglyceride, 3.39% diglyceride and 17.76% unknown compounds. The unknown compounds were separated via simple distillation carried out at a temperature range of 300-350oC.First, the experiments were carried out in screw capped bottles using filtrated as-received waste oil as the reactant. The esterification and transesterification process were conducted using sulfuric acid catalyst in a methanol solution. The key parameters studied were mole ratio of waste oil to methanol (1:1 to 1:72, amount of catalyst from 0.1-20 v/w% of the reactant, temperature range of 60-98oC and reaction time range of 15-180 minutes. Thin Layer Chromatography (TLC analysis showed 85-90% purity of methyl ester with 4-5% of mono-, di-, and triglycerides and fatty acids and about 5-10% of the unknown compounds for the best condition. The resulting yield of biodiesel was 84-88%. Eradication of contaminants by distillation gave about a 75% distillate yield. Distilled waste palm oil was esterified and transesterified using the previous optimum condition of as-received waste oil, but the reaction time and temperature were varied. The optimal result was obtained by using distilled waste palm oil to methanol molar ratio of 1:8, sulfuric acid of 1 v/w% of reactant, reaction temperature of 70oC and reaction time of 1 hour. TLC analysis indicated a biodiesel composition of methyl ester, free fatty acid, diglyceride and monoglyceride of 96.39%, 3.20%, 0.24% and 0.17%, respectively. The yield of biodiesel was 96-98% having physical fuel properties according to Thailand standard for methyl esterFinally, the distilled waste palm oil was esterified using a 3 liters continuous stirred-tank reactor (CSTR. Using the suitable condition for the batch process and an hour retention time, the

  16. Upgrading and Refining of Crude Oils and Petroleum Products by Ionizing Irradiation.

    Science.gov (United States)

    Zaikin, Yuriy A; Zaikina, Raissa F

    2016-06-01

    A general trend in the oil industry is a decrease in the proven reserves of light crude oils so that any increase in future oil exploration is associated with high-viscous sulfuric oils and bitumen. Although the world reserves of heavy oil are much greater than those of sweet light oils, their exploration at present is less than 12 % of the total oil recovery. One of the main constraints is very high expenses for the existing technologies of heavy oil recovery, upgrading, transportation, and refining. Heavy oil processing by conventional methods is difficult and requires high power inputs and capital investments. Effective and economic processing of high viscous oil and oil residues needs not only improvements of the existing methods, such as thermal, catalytic and hydro-cracking, but the development of new technological approaches for upgrading and refining of any type of problem oil feedstock. One of the perspective approaches to this problem is the application of ionizing irradiation for high-viscous oil processing. Radiation methods for upgrading and refining high-viscous crude oils and petroleum products in a wide temperature range, oil desulfurization, radiation technology for refining used oil products, and a perspective method for gasoline radiation isomerization are discussed in this paper. The advantages of radiation technology are simple configuration of radiation facilities, low capital and operational costs, processing at lowered temperatures and nearly atmospheric pressure without the use of any catalysts, high production rates, relatively low energy consumption, and flexibility to the type of oil feedstock.

  17. Oil extraction from microalgae for biodiesel production.

    Science.gov (United States)

    Halim, Ronald; Gladman, Brendan; Danquah, Michael K; Webley, Paul A

    2011-01-01

    This study examines the performance of supercritical carbon dioxide (SCCO(2)) extraction and hexane extraction of lipids from marine Chlorococcum sp. for lab-scale biodiesel production. Even though the strain of Chlorococcum sp. used in this study had a low maximum lipid yield (7.1 wt% to dry biomass), the extracted lipid displayed a suitable fatty acid profile for biodiesel [C18:1 (∼63 wt%), C16:0 (∼19 wt%), C18:2 (∼4 wt%), C16:1 (∼4 wt%), and C18:0 (∼3 wt%)]. For SCCO(2) extraction, decreasing temperature and increasing pressure resulted in increased lipid yields. The mass transfer coefficient (k) for lipid extraction under supercritical conditions was found to increase with fluid dielectric constant as well as fluid density. For hexane extraction, continuous operation with a Soxhlet apparatus and inclusion of isopropanol as a co-solvent enhanced lipid yields. Hexane extraction from either dried microalgal powder or wet microalgal paste obtained comparable lipid yields. Copyright © 2010 Elsevier Ltd. All rights reserved.

  18. Switching from monoculture to polyculture farming benefits birds in oil palm production landscapes: Evidence from mist netting data.

    Science.gov (United States)

    Yahya, Muhammad S; Syafiq, Muhamad; Ashton-Butt, Adham; Ghazali, Amal; Asmah, Siti; Azhar, Badrul

    2017-08-01

    Monoculture farming is pervasive in industrial oil palm agriculture, including those RSPO plantations certified as sustainably managed. This farming practice does not promote the maintenance of farmland biodiversity. However, little scientific attention has been given to polyculture farming in oil palm production landscapes. Polyculture farming is likely to increase the floristic diversity and stand structural complexity that underpins biodiversity. Mist nets were used to sample birds at 120 smallholdings in Peninsular Malaysia. At each site, 12 vegetation structure characteristics were measured. We compared bird species richness, abundance, and composition between monoculture and polyculture smallholdings and used predictive models to examine the effects of habitat quality on avian biodiversity. Bird species richness was significantly greater in polyculture than that of monoculture smallholdings. The number of fallen and standing, dead oil palms were also important positive predictors of species richness. Bird abundance was also strongly increased by standing and dead oil palms and decreased with oil palm stand height. Our results indicate that polyculture farming can improve bird species richness in oil palm production landscapes. In addition, key habitat variables that are closely associated with farming practices, such as the removal of dead trees, should and can be managed by oil palm growers in order to promote biodiversity. To increase the sustainability of oil palm agriculture, it is imperative that stakeholders modify the way oil palms are currently planted and managed. Our findings can guide policy makers and certification bodies to promote oil palm production landscapes that will function more sustainably and increase existing biodiversity of oil palm landscapes.

  19. Environmental Drivers of Differences in Microbial Community Structure in Crude Oil Reservoirs across a Methanogenic Gradient

    Science.gov (United States)

    Shelton, Jenna L.; Akob, Denise M.; McIntosh, Jennifer C.; Fierer, Noah; Spear, John R.; Warwick, Peter D.; McCray, John E.

    2016-01-01

    Stimulating in situ microbial communities in oil reservoirs to produce natural gas is a potentially viable strategy for recovering additional fossil fuel resources following traditional recovery operations. Little is known about what geochemical parameters drive microbial population dynamics in biodegraded, methanogenic oil reservoirs. We investigated if microbial community structure was significantly impacted by the extent of crude oil biodegradation, extent of biogenic methane production, and formation water chemistry. Twenty-two oil production wells from north central Louisiana, USA, were sampled for analysis of microbial community structure and fluid geochemistry. Archaea were the dominant microbial community in the majority of the wells sampled. Methanogens, including hydrogenotrophic and methylotrophic organisms, were numerically dominant in every well, accounting for, on average, over 98% of the total Archaea present. The dominant Bacteria groups were Pseudomonas, Acinetobacter, Enterobacteriaceae, and Clostridiales, which have also been identified in other microbially-altered oil reservoirs. Comparing microbial community structure to fluid (gas, water, and oil) geochemistry revealed that the relative extent of biodegradation, salinity, and spatial location were the major drivers of microbial diversity. Archaeal relative abundance was independent of the extent of methanogenesis, but closely correlated to the extent of crude oil biodegradation; therefore, microbial community structure is likely not a good sole predictor of methanogenic activity, but may predict the extent of crude oil biodegradation. However, when the shallow, highly biodegraded, low salinity wells were excluded from the statistical analysis, no environmental parameters could explain the differences in microbial community structure. This suggests that the microbial community structure of the 5 shallow, up-dip wells was different than the 17 deeper, down-dip wells. Also, the 17 down-dip wells

  20. Environmental Drivers of Differences in Microbial Community Structure in Crude Oil Reservoirs across a Methanogenic Gradient.

    Science.gov (United States)

    Shelton, Jenna L; Akob, Denise M; McIntosh, Jennifer C; Fierer, Noah; Spear, John R; Warwick, Peter D; McCray, John E

    2016-01-01

    Stimulating in situ microbial communities in oil reservoirs to produce natural gas is a potentially viable strategy for recovering additional fossil fuel resources following traditional recovery operations. Little is known about what geochemical parameters drive microbial population dynamics in biodegraded, methanogenic oil reservoirs. We investigated if microbial community structure was significantly impacted by the extent of crude oil biodegradation, extent of biogenic methane production, and formation water chemistry. Twenty-two oil production wells from north central Louisiana, USA, were sampled for analysis of microbial community structure and fluid geochemistry. Archaea were the dominant microbial community in the majority of the wells sampled. Methanogens, including hydrogenotrophic and methylotrophic organisms, were numerically dominant in every well, accounting for, on average, over 98% of the total Archaea present. The dominant Bacteria groups were Pseudomonas, Acinetobacter, Enterobacteriaceae, and Clostridiales, which have also been identified in other microbially-altered oil reservoirs. Comparing microbial community structure to fluid (gas, water, and oil) geochemistry revealed that the relative extent of biodegradation, salinity, and spatial location were the major drivers of microbial diversity. Archaeal relative abundance was independent of the extent of methanogenesis, but closely correlated to the extent of crude oil biodegradation; therefore, microbial community structure is likely not a good sole predictor of methanogenic activity, but may predict the extent of crude oil biodegradation. However, when the shallow, highly biodegraded, low salinity wells were excluded from the statistical analysis, no environmental parameters could explain the differences in microbial community structure. This suggests that the microbial community structure of the 5 shallow, up-dip wells was different than the 17 deeper, down-dip wells. Also, the 17 down-dip wells

  1. Environmental drivers of differences in microbial community structure in crude oil reservoirs across a methanogenic gradient

    Science.gov (United States)

    Shelton, Jenna L.; Akob, Denise M.; McIntosh, Jennifer C.; Fierer, Noah; Spear, John R.; Warwick, Peter D.; McCray, John E.

    2016-01-01

    Stimulating in situ microbial communities in oil reservoirs to produce natural gas is a potentially viable strategy for recovering additional fossil fuel resources following traditional recovery operations. Little is known about what geochemical parameters drive microbial population dynamics in biodegraded, methanogenic oil reservoirs. We investigated if microbial community structure was significantly impacted by the extent of crude oil biodegradation, extent of biogenic methane production, and formation water chemistry. Twenty-two oil production wells from north central Louisiana, USA, were sampled for analysis of microbial community structure and fluid geochemistry. Archaea were the dominant microbial community in the majority of the wells sampled. Methanogens, including hydrogenotrophic and methylotrophic organisms, were numerically dominant in every well, accounting for, on average, over 98% of the total Archaea present. The dominant Bacteria groups were Pseudomonas, Acinetobacter, Enterobacteriaceae, and Clostridiales, which have also been identified in other microbially-altered oil reservoirs. Comparing microbial community structure to fluid (gas, water, and oil) geochemistry revealed that the relative extent of biodegradation, salinity, and spatial location were the major drivers of microbial diversity. Archaeal relative abundance was independent of the extent of methanogenesis, but closely correlated to the extent of crude oil biodegradation; therefore, microbial community structure is likely not a good sole predictor of methanogenic activity, but may predict the extent of crude oil biodegradation. However, when the shallow, highly biodegraded, low salinity wells were excluded from the statistical analysis, no environmental parameters could explain the differences in microbial community structure. This suggests that the microbial community structure of the 5 shallow, up-dip wells was different than the 17 deeper, down-dip wells. Also, the 17 down-dip wells

  2. Environmental drivers of differences in microbial community structure in crude oil reservoirs across a methanogenic gradient

    Directory of Open Access Journals (Sweden)

    Jenna L Shelton

    2016-09-01

    Full Text Available Stimulating in situ microbial communities in oil reservoirs to produce natural gas is a potentially viable strategy for recovering additional fossil fuel resources following traditional recovery operations. Little is known about what geochemical parameters drive microbial population dynamics in biodegraded, methanogenic oil reservoirs. We investigated if microbial community structure was significantly impacted by the extent of crude oil biodegradation, extent of biogenic methane production, and formation water chemistry. Twenty-two oil production wells from north central Louisiana, USA, were sampled for analysis of microbial community structure and fluid geochemistry. Archaea were the dominant microbial community in the majority of the wells sampled. Methanogens, including hydrogenotrophic and methylotrophic organisms, were numerically dominant in every well, accounting for, on average, over 98% of the total archaea present. The dominant Bacteria groups were Pseudomonas, Acinetobacter, Enterobacteriaceae, and Clostridiales, which have also been identified in other microbially-altered oil reservoirs. Comparing microbial community structure to fluid (gas, water, and oil geochemistry revealed that the relative extent of biodegradation, salinity, and spatial location were the major drivers of microbial diversity. Archaeal relative abundance was independent of the extent of methanogenesis, but closely correlated to the extent of crude oil biodegradation; therefore, microbial community structure is likely not a good sole predictor of methanogenic activity, but may predict the extent of crude oil biodegradation. However, when the shallow, highly biodegraded, low salinity wells were excluded from the statistical analysis, no environmental parameters could explain the differences in microbial community structure. This suggests that the microbial community structure of the 5 shallow up-dip wells was different than the 17 deeper, down-dip wells, and that

  3. Oil Oxidative Transformation Products Revealed by Fourier Transform Ion Cyclotron Resonance Mass Spectrometry

    Science.gov (United States)

    Rodgers, R. P.; Podgorski, D. C.; Ray, P. Z.; McKenna, A. M.; Chen, H.; Clingenpeel, A. C.; Rowland, S. M.

    2016-02-01

    The chemical transformation of petrogenic carbon in the environment yields an incredible complex mixture of products that can dramatically alter native petroleum chemical functionalities. The changes affect toxicity, solubility, tendency for emulsion/mousse formation, aggregation, and ultimately, bioavailability. However, these changes are difficult to track at the molecular level, as the qualitative understanding of the (predominately) oxidative weathering is hampered by the immense complexity of the unaltered oil and multiplicative increase in complexity post-oxidation. Simply, a large fraction of unaltered oil that was initially accessible by GC-methods is chemically transformed into species that preclude GC based analyses. Thus, the fate of petrogenic transformation products and their potential to form undesirable future contaminants remain unknown. However, recent advances in analytical methodology and instrumentation now allow a molecular-level insight into these complex systems. Combined with the comprehensive analysis of the unaltered well oil, detailed compositional analysis of oil-impacted sites along the Gulf of Mexico coast over the past 4 years has revealed tens-of-thousands of previously unidentified, unique, biotic and abiotic transformation products that persist. Here, we highlight efforts to characterize oxidized transformation products, identify their oxygen functionalities, and demonstrate how they affect physical/chemical behavior of weathered oil. Temporal analysis of field samples reveal compositional changes of weathered oil as a function of oil contamination levels. Once determined, abiotic microcosm results are compared to the field samples to assess how well they account for observed changes in field samples. Finally, chromatographic separation of unaltered well oil (and surrogate) into structurally defined fractions (saturate, 1-ring, 2-ring, 3-ring, 4-ring and 5+ring aromatics / polars), followed by subsequent photo-oxidation of each

  4. Linking oil production to surface subsidence from satellite radar interferometry

    Science.gov (United States)

    Xu, Haibin; Dvorkin, Jack; Nur, Amos

    Land subsidence over the Belridge and Lost Hills oil fields, Southern California, was measured using spaceborne interferometric synthetic aperture radar (InSAR). During the 105-day period between 11/5/95 and 2/17/96, the subsidence in the center of the Lost Hills field reached 15 cm. We assume that this surface subsidence resulted from the vertical shrinkage of the reservoir, which in turn was due to oil production and the resulting pore pressure drop. We model this mechanical effect using an elastic deformation theoretical solution with input constants taken from relevant experiments. The modeled surface deformation matches the InSAR measured values. This result indicates that it is possible, in principle, to monitor hydrocarbon production using satellite-based measurements of earth deformation.

  5. Recent developments in microbial oils production: a possible alternative to vegetable oils for biodiesel without competition with human food?

    Directory of Open Access Journals (Sweden)

    Gwendoline Christophe

    2012-02-01

    Full Text Available Since centuries vegetable oils are consumed as human food but it also finds applications in biodiesel production which is attracting more attention. But due to being in competition with food it could not be sustainable and leads the need to search for alternative. Nowdays microbes-derived oils (single cell oils seem to be alternatives for biodiesel production due to their similar composition to that of vegetable oils. However, the cold flow properties of the biodiesel produced from microbial oils are unacceptable and have to be modified by an efficient transesterification. Glycerol which is by product of transesterification can be valorised into some more useful products so that it can also be utilised along with biodiesel to simplify the downstream processing. The review paper discusses about various potent microorganisms for biodiesel production, enzymes involved in the lipid accumulation, lipid quantification methods, catalysts used in transesterification (including enzymatic catalyst and valorisation of glycerol.

  6. Valorization of By-Products from Palm Oil Mills for the Production of Generic Fermentation Media for Microbial Oil Synthesis.

    Science.gov (United States)

    Tsouko, Erminda; Kachrimanidou, Vasiliki; Dos Santos, Anderson Fragoso; do Nascimento Vitorino Lima, Maria Eduarda; Papanikolaou, Seraphim; de Castro, Aline Machado; Freire, Denise Maria Guimarães; Koutinas, Apostolis A

    2017-04-01

    This study demonstrates the production of a generic nutrient-rich feedstock using by-product streams from palm oil production that could be used as a substitute for commercial fermentation supplements. Solid-state fermentations of palm kernel cake (PKC) and palm-pressed fiber (PPF) were conducted in tray bioreactors and a rotating drum bioreactor by the fungal strain Aspergillus oryzae for the production of crude enzymes. The production of protease was optimized (319.3 U/g) at an initial moisture content of 55 %, when PKC was used as the sole substrate. The highest free amino nitrogen (FAN) production (5.6 mg/g) obtained via PKC hydrolysis using the crude enzymes produced via solid-state fermentation was achieved at 50 °C. Three initial PKC concentrations (48.7, 73.7, and 98.7 g/L) were tested in hydrolysis experiments, leading to total Kjeldahl nitrogen to FAN conversion yields up to 27.9 %. Sequential solid-state fermentation followed by hydrolysis was carried out in the same rotating drum bioreactor, leading to the production of 136.7 U/g of protease activity during fermentation and 196.5 mg/L of FAN during hydrolysis. Microbial oil production was successfully achieved with the oleaginous yeast strain Lipomyces starkeyi DSM 70296 cultivated on the produced PKC hydrolysate mixed with commercial carbon sources, including glucose, xylose, mannose, galactose, and arabinose.

  7. Robust control charts in industrial production of olive oil

    Science.gov (United States)

    Grilo, Luís M.; Mateus, Dina M. R.; Alves, Ana C.; Grilo, Helena L.

    2014-10-01

    Acidity is one of the most important variables in the quality analysis and characterization of olive oil. During the industrial production we use individuals and moving range charts to monitor this variable, which is not always normal distributed. After a brief exploratory data analysis, where we use the bootstrap method, we construct control charts, before and after a Box-Cox transformation, and compare their robustness and performance.

  8. Waste cooking oil as an alternate feedstock for biodiesel production

    Energy Technology Data Exchange (ETDEWEB)

    Chhetri, A. B.; Rafiqul Islam, M. [Civil and Resources Engineering Dalhousie University, Room D510, 1360 Barrington St., Box 1000, Halifax, N.S. B3J 2X4 (Canada); Watts, K. Ch. [Process Engineering, Dalhousie University, Halifax, NS, Box 1000, Halifax, N.S. B3J 2X4 (Canada)

    2008-07-01

    As crude oil price reach a new high, the need for developing alternate fuels has become acute. Alternate fuels should be economically attractive in order to compete with currently used fossil fuels. In this work, biodiesel (ethyl ester) was prepared from waste cooking oil collected from a local restaurant in Halifax, Nova Scotia, Canada. Ethyl alcohol with sodium hydroxide as a catalyst was used for the transesterification process. The fatty acid composition of the final biodiesel esters was determined by gas chromatography. The biodiesel was characterized by its physical and fuel properties including density, viscosity, acid value, flash point, cloud point, pour point, cetane index, water and sediment content, total and free glycerin content, diglycerides and monoglycerides, phosphorus content and sulfur content according to ASTM standards. The viscosity of the biodiesel ethyl ester was found to be 5.03 mm{sup 2}/sec at 40 {sup o}C. The viscosity of waste cooking oil measured in room temperature (at 21 {sup o}C) was 72 mm{sup 2}/sec. From the tests, the flash point was found to be 164 {sup o}C, the phosphorous content was 2 ppm, those of calcium and magnesium were 1 ppm combined, water and sediment was 0 %, sulfur content was 2 ppm, total acid number was 0.29 mg KOH/g, cetane index was 61, cloud point was -1 {sup o}C and pour point was -16 {sup o}C. Production of biodiesel from waste cooking oils for diesel substitute is particularly important because of the decreasing trend of economical oil reserves, environmental problems caused due to fossil fuel use and the high price of petroleum products in the international market. (author)

  9. Waste Cooking Oil as an Alternate Feedstock for Biodiesel Production

    Directory of Open Access Journals (Sweden)

    M. Rafiqul Islam

    2008-04-01

    Full Text Available As crude oil price reach a new high, the need for developing alternate fuels has become acute. Alternate fuels should be economically attractive in order to compete with currently used fossil fuels. In this work, biodiesel (ethyl ester was prepared from waste cooking oil collected from a local restaurant in Halifax, Nova Scotia, Canada. Ethyl alcohol with sodium hydroxide as a catalyst was used for the transesterification process. The fatty acid composition of the final biodiesel esters was determined by gas chromatography. The biodiesel was characterized by its physical and fuel properties including density, viscosity, acid value, flash point, cloud point, pour point, cetane index, water and sediment content, total and free glycerin content, diglycerides and monoglycerides, phosphorus content and sulfur content according to ASTM standards. The viscosity of the biodiesel ethyl ester was found to be 5.03 mm2/sec at 40oC. The viscosity of waste cooking oil measured in room temperature (at 21° C was 72 mm2/sec. From the tests, the flash point was found to be 164oC, the phosphorous content was 2 ppm, those of calcium and magnesium were 1 ppm combined, water and sediment was 0 %, sulfur content was 2 ppm, total acid number was 0.29 mgKOH/g, cetane index was 61, cloud point was -1oC and pour point was -16oC. Production of biodiesel from waste cooking oils for diesel substitute is particularly important because of the decreasing trend of economical oil reserves, environmental problems caused due to fossil fuel use and the high price of petroleum products in the international market.

  10. Impact of oil on bacterial community structure in bioturbated sediments.

    Directory of Open Access Journals (Sweden)

    Magalie Stauffert

    Full Text Available Oil spills threaten coastlines where biological processes supply essential ecosystem services. Therefore, it is crucial to understand how oil influences the microbial communities in sediments that play key roles in ecosystem functioning. Ecosystems such as sediments are characterized by intensive bioturbation due to burrowing macrofauna that may modify the microbial metabolisms. It is thus essential to consider the bioturbation when determining the impact of oil on microbial communities. In this study, an experimental laboratory device maintaining pristine collected mudflat sediments in microcosms closer to true environmental conditions--with tidal cycles and natural seawater--was used to simulate an oil spill under bioturbation conditions. Different conditions were applied to the microcosms including an addition of: standardized oil (Blend Arabian Light crude oil, 25.6 mg.g⁻¹ wet sediment, the common burrowing organism Hediste (Nereis diversicolor and both the oil and H. diversicolor. The addition of H. diversicolor and its associated bioturbation did not affect the removal of petroleum hydrocarbons. After 270 days, 60% of hydrocarbons had been removed in all microcosms irrespective of the H. diversicolor addition. However, 16S-rRNA gene and 16S-cDNA T-RFLP and RT-PCR-amplicon libraries analysis showed an effect of the condition on the bacterial community structure, composition, and dynamics, supported by PerMANOVA analysis. The 16S-cDNA libraries from microcosms where H. diversicolor was added (oiled and un-oiled showed a marked dominance of sequences related to Gammaproteobacteria. However, in the oiled-library sequences associated to Deltaproteobacteria and Bacteroidetes were also highly represented. The 16S-cDNA libraries from oiled-microcosms (with and without H. diversicolor addition revealed two distinct microbial communities characterized by different phylotypes associated to known hydrocarbonoclastic bacteria and dominated by

  11. The possibility of palm oil mill effluent for biogas production

    Directory of Open Access Journals (Sweden)

    EDWI MAHAJOENO

    2008-01-01

    Full Text Available The world currently obtains its energy from the fossil fuels such as oil, natural gas and coal. However, the international crisis in the Middle East, rapid depletion of fossil fuel reserves as well as climate change have driven the world towards renewable energy sources which are abundant, untapped and environmentally friendly. Indonesia has abundant biomass resources generated from the agricultural industry particularly the large commodity, palm oil (Elaeis guiinensis Jacq.. The aims of the research were to (i characterize palm oil mill effluent which will be used as source of biogas production, (ii know the biotic and abiotic factors which effect POME substrate for biogas production by anaerobic digestion in bulk system. The results show that POME sludge generated from PT Pinago Utama mill is viscous, brown or grey and has an average total solid (TS content of, 26.5-45.4, BOD is 23.5-29.3, COD is 49.0-63.6 and SS is 17.1-35.9 g/L, respectively. This substrate is a potential source of environmental pollutants. The biotic factors were kind and concentration of the inoculums, i.e. seed sludge of anaerobic lagoon II and 20% (w/v respectively. Both physical and chemical factors such as pre-treated POME pH, pH neutralizer matter Ca (OH2, temperature ≥40oC, agitation effect to increase biogas production, but in both coagulant concentration, FeCl2 were not.

  12. Potential of eleven Eucalyptus species for the production of essential oils

    OpenAIRE

    2006-01-01

    Most Eucalyptus plantations in Brazil aim the production of paper and charcoal, but the use of the species for lumbering, construction and extraction of essential oil has increased. Eleven species of Eucalyptus were assessed in regard to their essential oil production potential, nine never used before for commercial, essential oil extraction. Assessements were compared with Eucalyptus citriodora and Eucalyptus globulus, already explored in oil production for perfume and medical purposes, aimi...

  13. Alkaline direct transesterification of different species of Stichococcus for bio-oil production.

    Science.gov (United States)

    Gargano, Immacolata; Marotta, Raffaele; Andreozzi, Roberto; Olivieri, Giuseppe; Marzocchella, Antonio; Spasiano, Danilo; Pinto, Gabriele; Pollio, Antonino

    2016-12-25

    The cost of bio-oil refining from microalgal biomass can be significantly reduced by combining extraction and transesterification. The characterisation and optimisation of the combined steps have been carried out on strains of Stichococcus bacillaris, focusing on catalyst type and concentration, reaction time and temperature, methanol/biomass ratio, pre-mixing time and water content in the biomass. The bio-oil yield has been referenced as production of fatty acid methyl esters (FAMEs). The maximum yield (∼17%) was achieved using dried biomass with alkaline catalyst at 60°C and methanol/biomass weight ratio of 79:1. Alkaline catalyst conditions gave faster reaction rates and higher bio-oil yields than acid catalyst. Yield was also strongly affected by water content in the biomass. A mechanistic interpretation has been proposed to elucidate the effect of the different operating conditions. However, the structural characteristics of the Chlorophyta cell wall can be very different, leading to different bio-oil yields when the same protocol is applied. Therefore, the optimised protocol of direct transesterification for Stichococcus bacillaris strains was tested on other Stichococcus strains and several other Chlorophyta species characterised by a different cell wall structure. It was clearly demonstrated that different results for bio-oil yield were obtained within the same microalgal species and much more within different microalgal genera.

  14. Life cycle inventory for the production of germinated oil palm seeds at a selected seed production unit in Malaysia

    Science.gov (United States)

    Khairuddin, Nik Sasha Khatrina; Ismail, B. S.; Muhamad, Halimah; May, Choo Yuen

    2013-11-01

    The increasing global demand for edible oil has encouraged Malaysia to increase the areas under oil palm cultivation. The total demand for germinated oil palm seeds in the years 2009, 2010, 2011 and 2012 were 86.4, 76.5, 72.6 and 75.2 million, respectively. Production of germinated oil palm seeds is the first link in the palm oil supply chain. Therefore, good management practices at seed production stage is required to ensure only high quality germinated oil palm seeds are produced before sale to customers. Life cycle assessment (LCA) has been used as a tool to assess environmental impact of the processes throughout a product's lifespan and this approach is an important tool for assessing green house gas (GHG) emission. For this study, a gate-to-gate life cycle inventory (LCI) of a single germinated oil palm seed production unit was carried out. The functional unit used for this LCI was one germinated oil palm seed. To determine the environmental impact for the production of germinated oil palm seeds, information on the inputs were obtained. The inputs for the production of germinated oil palm seeds involved materials such as polyethylene bags, electricity, water, chemicals and fungicides. For this study, the system boundary involved seed germination process and management of germinated oil palm seeds. It was found that the amount of input such as materials and energy used in the production of germinated oil palm seeds was very minimal.

  15. Organic Substances from Unconventional Oil and Gas Production in Shale

    Science.gov (United States)

    Orem, W. H.; Varonka, M.; Crosby, L.; Schell, T.; Bates, A.; Engle, M.

    2014-12-01

    Unconventional oil and gas (UOG) production has emerged as an important element in the US and world energy mix. Technological innovations in the oil and gas industry, especially horizontal drilling and hydraulic fracturing, allow for the enhanced release of oil and natural gas from shale compared to conventional oil and gas production. This has made commercial exploitation possible on a large scale. Although UOG is enormously successful, there is surprisingly little known about the effects of this technology on the targeted shale formation and on environmental impacts of oil and gas production at the surface. We examined water samples from both conventional and UOG shale wells to determine the composition, source and fate of organic substances present. Extraction of hydrocarbon from shale plays involves the creation and expansion of fractures through the hydraulic fracturing process. This process involves the injection of large volumes of a water-sand mix treated with organic and inorganic chemicals to assist the process and prop open the fractures created. Formation water from a well in the New Albany Shale that was not hydraulically fractured (no injected chemicals) had total organic carbon (TOC) levels that averaged 8 mg/L, and organic substances that included: long-chain fatty acids, alkanes, polycyclic aromatic hydrocarbons, heterocyclic compounds, alkyl benzenes, and alkyl phenols. In contrast, water from UOG production in the Marcellus Shale had TOC levels as high as 5,500 mg/L, and contained a range of organic chemicals including, solvents, biocides, scale inhibitors, and other organic chemicals at thousands of μg/L for individual compounds. These chemicals and TOC decreased rapidly over the first 20 days of water recovery as injected fluids were recovered, but residual organic compounds (some naturally-occurring) remained up to 250 days after the start of water recovery (TOC 10-30 mg/L). Results show how hydraulic fracturing changes the organic

  16. Biodeterioration problems of North sea oil and gas production - a review

    Energy Technology Data Exchange (ETDEWEB)

    Edyvean, R.G.J.

    1987-01-01

    The North Sea is both a highly corrosive and highly biologically productive environment. Oil and gas production structures in this environment not only suffer from the physical effects, corrosion, wave and storm action, of being immersed in this environment, but also the effects of biological activity. Such biodeterioration problems occur both on the external and internal surfaces of the structure and the internal surfaces of any plant or pipework which contains, or has contained, water. The platform jacket may experience biological problems due to external macro- and microfouling or to internal microfouling. Pipelines, risers and topside systems have usually all been hydrostatically tested leaving residual water and possible sites for bacterial activity. Waterflooding with seawater and the separation of produced water from oil also provide sites suitable for biological activity and associated corrosion, slime and blockage problems.

  17. Enzymatic production of biodiesel from canola oil using immobilized lipase

    Energy Technology Data Exchange (ETDEWEB)

    Dizge, Nadir; Keskinler, Buelent [Department of Environmental Engineering, Gebze Institute of Technology, Gebze 41400 (Turkey)

    2008-12-15

    In the present work, a novel method for immobilization of lipase within hydrophilic polyurethane foams using polyglutaraldehyde was developed for the immobilization of Thermomyces lanuginosus lipase to produce biodiesel with canola oil and methanol. The enzyme optimum conditions were not affected by immobilization and the optimum pH for free and immobilized enzyme were 6, resulting in 80% immobilization yield. Using the immobilized lipase T. lanuginosus, the effects of enzyme loading, oil/alcohol molar ratio, water concentration, and temperature in the transesterification reaction were investigated. The optimal conditions for processing 20 g of refined canola oil were: 430 {mu}g lipase, 1:6 oil/methanol molar ratio, 0.1 g water and 40 C for the reactions with methanol. Maximum methyl esters yield was 90% of which enzymatic activity remained after 10 batches, when tert-butanol was adopted to remove by-product glycerol during repeated use of the lipase. The immobilized lipase proved to be stable and lost little activity when was subjected to repeated uses. (author)

  18. The Potential of Microalgae Lipids for Edible Oil Production.

    Science.gov (United States)

    Huang, Yanfei; Zhang, Dongmei; Xue, Shengzhang; Wang, Meng; Cong, Wei

    2016-10-01

    The objective of this study was to evaluate the potential of oil-rich green algae, Chlorella vulgaris, Scenedesmus obliquus, and Nannochloropsis oceanica, to produce edible oil with respect to lipid and residue properties. The results showed that C. vulgaris and N. oceanica had similarly much higher lipid recovery (about 50 %) in hexane extraction than that of S. obliquus (about 25 %), and C. vulgaris had the highest content of neutral lipids among the three algae. The fatty acid compositions of neutral lipids from C. vulgaris and S. obliquus were mainly C16 and C18, resembling that of vegetable oils. ARA and EPA were the specific valuable fatty acids in lipids of N. oceanica, but the content of which was lower in neutral lipids. Phytol was identified as the major unsaponifiable component in lipids of the three algae. Combined with the evaluation of the ratios in SFA/MUFA/PUFA, (n-6):(n-3) and content of free fatty acids, lipids obtained from C. vulgaris displayed the great potential for edible oil production. Lipids of N. oceanica showed the highest antioxidant activity, and its residue contained the largest amounts of protein as well as the amino acid compositions were greatly beneficial to the health of human beings.

  19. Microbiological Production of Citric and Isocitric Acids from Sunflower Oil

    Directory of Open Access Journals (Sweden)

    Svetlana V. Kamzolova

    2008-01-01

    Full Text Available The growth of wild type strain Yarrowia lipolytica VKM Y-2373 and its mutant Yarrowia lipolytica N 15 as well the biosynthesis of citric and isocitric acids on sunflower oil were studied. It was indicated that cell growth was associated with the simultaneous utilization of glycerol and free fatty acids produced during oil hydrolysis. The activities of enzymes of glycerol metabolism (glycerol kinase, fatty acid assimilation enzymes of glyoxylate cycle (isocitrate lyase and malate synthase and citric acid cycle were comparatively assayed in Y. lipolytica grown on sunflower oil, glycerol and oleic acid. Glycerol kinase and enzymes of glyoxylate cycle were active during the whole period of cell cultivation on sunflower oil. Citric acid production and a ratio between citric and isocitric acids depended on both the strain used and the medium composition. It was revealed that wild type strain Y. lipolytica VKM Y-2373 produced almost equal amounts of citric and isocitric acids at pH=4.5 and predominantly accumulated isocitric acid at pH=6.0. The mutant Y. lipolytica N 15 produced only citric acid (150 g/L with mass yield (YCA of 1.32 g/g. Biochemical characteristics of mutant strain Y. lipolytica N 15 were discussed.

  20. The Relationship between Major Oil Products Consumption and Efficiency of Industry Sector in Selected Oil Exporting and Importing Countries

    Directory of Open Access Journals (Sweden)

    Ali Akbar Naji MEIDANI

    2013-11-01

    Full Text Available The aim of this study is to investigate the realization of the law of diminishing returns in usage of major oil products in the industry sector of some oil exporting and importing countries during 2002- 2008. To achieve this aim, in a first stage the efficiency of industry sector of countries has been calculated using DEA window analysis and then in the second stag the existence of an inverted U' shape relationship between major oil product consumption and efficiency has been tested in the context of dynamic panel data (GMM approach. The results confirm this relationship in each group of countries except that the turning point in the case of oil importing countries is much higher than oil exporting countries. This firstly suggests that oil dependence in oil importing countries is more than oil exporting countries and secondly indicates that the industry sector of oil importing countries have advanced technology and high scale and capacity so that they can take benefits of oil products consumption without decrease in efficiency.

  1. Structural Study of Asphaltenes from Iranian Heavy Crude Oil

    Directory of Open Access Journals (Sweden)

    Davarpanah L.

    2015-11-01

    Full Text Available In the present study, asphaltene precipitation from Iranian heavy crude oil (Persian Gulf off-shore was performed using n-pentane (n-C5 and n-heptane (n-C7 as light alkane precipitants. Several analytical techniques, each following different principles, were then used to structurally characterize the precipitated asphaltenes. The yield of asphaltene obtained using n-pentane precipitant was higher than asphaltene precipitated with the use of n-heptane. The asphaltene removal affected the n-C5 and n-C7 maltene fractions at temperatures below 204°C, as shown by the data obtained through the simulated distillation technique. Viscosity of heavy oil is influenced by the asphaltene content and behavior. The viscosity dependence of the test heavy oil on the shear rate applied was determined and the flow was low at y. above 25 s-1 . The reconstituted heavy oil samples were prepared by adding different amounts of asphaltenes to the maltenes (deasphalted heavy oil and asphaltene effects were more pronounced at the low temperature of 25°C as compared with those at the higher temperatures. According to the power law model used in this study the flowability of the test heavy oil exhibited a pseudoplastic character. Structural results obtained from Fourier Transform InfraRed (FTIR spectroscopy showed the presence of the different functional groups in the precipitated asphaltenes. For instance, the presence of different hydrocarbons (aliphatic, aromatic and alicyclic based on their characteristics in the FTIR spectra was confirmed. Resins are effective dispersants, and removal of this fraction from the crude oil is disturbing to the colloidal nature of heavy oil; asphaltene flocculation and precipitation eventually occur. Appearance of pores in the Scanning Electron Microscopy (SEM images was used as an indicator of the resin detachment. With the use of 1H and 13C Nuclear Magnetic Resonance (NMR spectroscopy, two important structural parameters of the

  2. PRICE DISCRIMINATION IN CONDITION OF OIL PRODUCT EXCHANGE

    Directory of Open Access Journals (Sweden)

    Anna Elagina

    2015-01-01

    Full Text Available The development of exchange trading of oil products in the Russian Federation was intended as an instrument of control of market power by dominant economic entities, support of development of business wholesale and retail trade, liberalization of service markets fuel supply at airports. However, practice of the trading development shows that in terms of institutional trades can occur prerequisites for the development of price discrimination. Therefore, the development of data analysis tools in the conditions for petroleum product trading development is a very important area in the development of Antimonopoly control.

  3. Cultivation of Herbs and Medicinal Plants in Norway - Essential Oil Production and Quality Control

    OpenAIRE

    Rohloff, Jens

    2003-01-01

    Essential oils (EO) are plant secondary metabolites that are known for their fragrance and food flavour properties. They consist of a complex mixture of mono- and sesquiterpenes, phenyl propanoids and oxygenated compounds. EOs can be present in different plant organs and materials, and their storage is related to specialised secretory structures. The yield of EOs from plant raw materials by distillation or pressing may on average vary from 0.1 – 1%, thus restricting the major EO production to...

  4. Indonesia palm oil production without deforestation and peat conversion by 2050.

    Science.gov (United States)

    Afriyanti, Dian; Kroeze, Carolien; Saad, Asmadi

    2016-07-01

    Palm oil is a promising source of cooking oil and biodiesel. The demand for palm oil has been increasing worldwide. However, concerns exist surrounding the environmental and socio-economic sustainability of palm oil production. Indonesia is a major palm oil producing country. We explored scenarios for palm oil production in Indonesia until 2050, focusing on Sumatra, Kalimantan and Papua. Our scenarios describe possible trends in crude palm oil production in Indonesia, while considering the demand for cooking oil and biodiesel, the available land for plantations, production capacity (for crude palm oil and fresh fruit bunches) and environmentally restricting conditions. We first assessed past developments in palm oil production. Next, we analysed scenarios for the future. In the past 20years, 95% of the Indonesian oil palm production area was in Sumatra and Kalimantan and was increasingly cultivated in peatlands. Our scenarios for the future indicate that Indonesia can meet a considerable part of the global and Asian demand for palm oil, while avoiding further cultivation of peatlands and forest. By 2050, 264-447Mt crude palm oil may be needed for cooking oil and biodiesel worldwide. In Indonesia, the area that is potentially suitable for oil palm is 17 to 26Mha with a potential production rate of 27-38t fresh fruit bunches/ha, yielding 130-176Mt crude palm oil. Thus Indonesia can meet 39-60% of the international demand. In our scenarios this would be produced in Sumatra (21-26%), Kalimantan (12-16%), and Papua (2%). The potential areas include the current oil palm plantation in mineral lands, but exclude the current oil palm plantations in peatlands.

  5. Economic assessment of biodiesel production from waste frying oils.

    Science.gov (United States)

    Araujo, Victor Kraemer Wermelinger Sancho; Hamacher, Silvio; Scavarda, Luiz Felipe

    2010-06-01

    Waste frying oils (WFO) can be a good source for the production of biodiesel because this raw material is not part of the food chain, is low cost and can be used in a way that resolves environmental problems (i.e. WFO is no longer thrown into the sewage network). The goal of this article is to propose a method to evaluate the costs of biodiesel production from WFO to develop an economic assessment of this alternative. This method embraces a logistics perspective, as the cost of collection of oil from commercial producers and its delivery to biodiesel depots or plants can be relevant and is an issue that has been little explored in the academic literature. To determine the logistics cost, a mathematical programming model is proposed to solve the vehicle routing problem (VRP), which was applied in an important urban center in Brazil (Rio de Janeiro), a relevant and potential center for biodiesel production and consumption. Eighty-one biodiesel cost scenarios were compared with information on the commercialization of biodiesel in Brazil. The results obtained demonstrate the economic viability of biodiesel production from WFO in the urban center studied and the relevance of logistics in the total biodiesel production cost. (c) 2010 Elsevier Ltd. All rights reserved.

  6. Mineral oil and synthetic hydrocarbons in cosmetic lip products.

    Science.gov (United States)

    Niederer, M; Stebler, T; Grob, K

    2016-04-01

    Lipsticks and lip care products may contain saturated hydrocarbons which either stem from mineral oil saturated hydrocarbons (MOSH) or are synthetic, that is polyolefin oligomeric saturated hydrocarbons (POSH). Some of these hydrocarbons are strongly accumulated and form granulomas in human tissues, which prompted Cosmetics Europe (former Colipa) to issue a recommendation for their use in lip care and oral products. From 2012 to 2014, MOSH+POSH were determined in 175 cosmetic lip products taken from the Swiss market in order to estimate their contribution to human exposure. Mineral oil saturated hydrocarbons and POSH were extracted and analysed by GC with FID. Areas were integrated as a total as well as by mass ranges with cuts at n-C25 and n-C34 to characterize the molecular mass distribution. About 68% of the products contained at least 5% MOSH+POSH (total concentration). For regular users, these products would be major contributors to their MOSH+POSH exposure. About 31% of the products contained more than 32% MOSH+POSH. Their regular usage would amount in an estimated MOSH+POSH exposure exceeding the highest estimated dietary exposure. The majority of the products contained hydrocarbons with a molecular mass range which was not in line with the recommendations of Cosmetics Europe. Taking into account that material applied to the lips largely ends up being ingested, MOSH and POSH levels should be reduced in the majority of cosmetic lip products. As the extensive evaluation of the data available on MOSH (EFSA J., 10, 2012, 2704) did not enable the specification of limits considered as safe, the present level of dietary exposure and its evaluation as 'of potential concern' provide the relevant bench mark, which means that lip products should contain clearly less than 5% MOSH+POSH. © 2015 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

  7. Production Strategies and Applications of Microbial Single Cell Oils

    Science.gov (United States)

    Ochsenreither, Katrin; Glück, Claudia; Stressler, Timo; Fischer, Lutz; Syldatk, Christoph

    2016-01-01

    Polyunsaturated fatty acids (PUFAs) of the ω-3 and ω-6 class (e.g., α-linolenic acid, linoleic acid) are essential for maintaining biofunctions in mammalians like humans. Due to the fact that humans cannot synthesize these essential fatty acids, they must be taken up from different food sources. Classical sources for these fatty acids are porcine liver and fish oil. However, microbial lipids or single cell oils, produced by oleaginous microorganisms such as algae, fungi and bacteria, are a promising source as well. These single cell oils can be used for many valuable chemicals with applications not only for nutrition but also for fuels and are therefore an ideal basis for a bio-based economy. A crucial point for the establishment of microbial lipids utilization is the cost-effective production and purification of fuels or products of higher value. The fermentative production can be realized by submerged (SmF) or solid state fermentation (SSF). The yield and the composition of the obtained microbial lipids depend on the type of fermentation and the particular conditions (e.g., medium, pH-value, temperature, aeration, nitrogen source). From an economical point of view, waste or by-product streams can be used as cheap and renewable carbon and nitrogen sources. In general, downstream processing costs are one of the major obstacles to be solved for full economic efficiency of microbial lipids. For the extraction of lipids from microbial biomass cell disruption is most important, because efficiency of cell disruption directly influences subsequent downstream operations and overall extraction efficiencies. A multitude of cell disruption and lipid extraction methods are available, conventional as well as newly emerging methods, which will be described and discussed in terms of large scale applicability, their potential in a modern biorefinery and their influence on product quality. Furthermore, an overview is given about applications of microbial lipids or derived fatty

  8. Production Strategies and Applications of Microbial Single Cell Oils.

    Science.gov (United States)

    Ochsenreither, Katrin; Glück, Claudia; Stressler, Timo; Fischer, Lutz; Syldatk, Christoph

    2016-01-01

    Polyunsaturated fatty acids (PUFAs) of the ω-3 and ω-6 class (e.g., α-linolenic acid, linoleic acid) are essential for maintaining biofunctions in mammalians like humans. Due to the fact that humans cannot synthesize these essential fatty acids, they must be taken up from different food sources. Classical sources for these fatty acids are porcine liver and fish oil. However, microbial lipids or single cell oils, produced by oleaginous microorganisms such as algae, fungi and bacteria, are a promising source as well. These single cell oils can be used for many valuable chemicals with applications not only for nutrition but also for fuels and are therefore an ideal basis for a bio-based economy. A crucial point for the establishment of microbial lipids utilization is the cost-effective production and purification of fuels or products of higher value. The fermentative production can be realized by submerged (SmF) or solid state fermentation (SSF). The yield and the composition of the obtained microbial lipids depend on the type of fermentation and the particular conditions (e.g., medium, pH-value, temperature, aeration, nitrogen source). From an economical point of view, waste or by-product streams can be used as cheap and renewable carbon and nitrogen sources. In general, downstream processing costs are one of the major obstacles to be solved for full economic efficiency of microbial lipids. For the extraction of lipids from microbial biomass cell disruption is most important, because efficiency of cell disruption directly influences subsequent downstream operations and overall extraction efficiencies. A multitude of cell disruption and lipid extraction methods are available, conventional as well as newly emerging methods, which will be described and discussed in terms of large scale applicability, their potential in a modern biorefinery and their influence on product quality. Furthermore, an overview is given about applications of microbial lipids or derived fatty

  9. Production strategies and applications of microbial single cell oils

    Directory of Open Access Journals (Sweden)

    Katrin Ochsenreither

    2016-10-01

    Full Text Available Polyunsaturated fatty acids (PUFAs of the -3 and -6 class (e.g. -linolenic acid, linoleic acid are essential for maintaining biofunctions in mammalians like humans. Due to the fact that humans cannot synthesize these essential fatty acids, they must be taken up from different food sources. Classical sources for these fatty acids are porcine liver and fish oil. However, microbial lipids or single cell oils, produced by oleaginous microorganisms such as algae, fungi and bacteria, are a promising source as well. These single cell oils can be used for many valuable chemicals with applications not only for nutrition but also for fuels and are therefore an ideal basis for a bio-based economy. A crucial point for the establishment of microbial lipids utilization is the cost-effective production and purification of fuels or products of higher value. The fermentative production can be realized by submerged (SmF or solid state fermentation (SSF. The yield and the composition of the obtained microbial lipids depend on the type of fermentation and the particular conditions (e.g. medium, pH-value, temperature, aeration, nitrogen source. From an economical point of view, waste or by-product streams can be used as cheap and renewable carbon and nitrogen sources. In general, downstream processing costs are one of the major obstacles to be solved for full economic efficiency of microbial lipids. For the extraction of lipids from microbial biomass cell disruption is most important, because efficiency of cell disruption directly influences subsequent downstream operations and overall extraction efficiencies. A multitude of cell disruption and lipid extraction methods are available, conventional as well as newly emerging methods, which will be described and discussed in terms of large scale applicability, their potential in a modern biorefinery and their influence on product quality. Furthermore, an overview is given about applications of microbial lipids

  10. Effects of temperature on pyrolysis products of oil sludge

    Institute of Scientific and Technical Information of China (English)

    Jianguo LIU; Wei SONG; Yongfeng NIE

    2008-01-01

    Temperature is the determining factor of pyrolysis, which is one of the alternative technologies for oil sludge treatment. The effects of final:operating temperature ranging from 350 to 550℃ on pyrolysis products of oil sludge were studied in an externally-heating fixed bed reactor. With an increase of temperature, the mass fraction of solid residues, liquids, and gases in the final product is 67.00%-56.00%, 25.60%-32.35%, and 7.40%-11.65%, and their coresponding heat values are 34.4-13.8 MJ/kg, 44.41-46.6 MJ/kg, and 23.94-48.23 MJ/Nm3, respectively. The mass and energy tend to shift from solid to liquid and gas phase (especially to liquid phase) during the process, and the optimum temperature for oil sludge pyrolysis is 500℃. The liquid phase is mainly composed of alkane and alkene (C5.-C29), and the gas phase is dominantly HCs and H2.

  11. Bio-oil Production - Process Optimization and Product Quality

    DEFF Research Database (Denmark)

    Hoffmann, Jessica

    and pharmaceutical products, it will become a high-cost commodity. Therefore it is of great importance to develop a sustainable and marketable process for the conversion of biomass, which is feedstock flexible and energy efficient and offers high conversion efficiency. Only a process like this has the ability......, fossil fuels still accounted for 87% of global and 81% of EU primary energy consumption. In an effort to reduce the carbon footprint of a continued supply of liquid fuels, processes utilizing biomass in general, and lignocellulosic biomass in particular, are being developed to replace their fossil...... to produce a drop-in product that is commercially compatible to conventional fuels as wells as has the capability to endure. Furthermore, liquid biofuels in future need to be produced in bulk to meet demand; thus, the challenge becomes one of finding the right process with high feedstock flexibility. One...

  12. Rooted structuring as key for Southern Apennine oil exploration

    Energy Technology Data Exchange (ETDEWEB)

    Ben, Anna del; Finetti, Icilio [Trieste Univ. (Italy). EGG

    1999-07-01

    It is Authors' opinion that a key point for the evaluation of the prospect in Southern Apennine, having as target the top of the Apulian Platform, is constituted by the type of the structure involved. That is, if the explored feature is formed by a block rooted with its own basement and practically not or not much displaced, in that case the preservation of the integrity of the reservoir and its oil trapping is possible. But when the explored structure consists of thrust-blocks, disrooted from their basement and prominently displaced, than the resulting reservoir/cover conditions do not allow oil trapping or preservation of oil accumulation. Examples of both types of features are examined. (author)

  13. Increasing Heavy Oil Reserves in the Wilmington Oil Field Through Advanced Reservoir Characterization and Thermal Production Technologies, Class III

    Energy Technology Data Exchange (ETDEWEB)

    City of Long Beach; Tidelands Oil Production Company; University of Southern California; David K. Davies and Associates

    2002-09-30

    The objective of this project was to increase the recoverable heavy oil reserves within sections of the Wilmington Oil Field, near Long Beach, California through the testing and application of advanced reservoir characterization and thermal production technologies. It was hoped that the successful application of these technologies would result in their implementation throughout the Wilmington Field and, through technology transfer, will be extended to increase the recoverable oil reserves in other slope and basin clastic (SBC) reservoirs.

  14. Production of Biodiesel from Shea Butter Oil using Homogeneous Catalysts

    Directory of Open Access Journals (Sweden)

    Jude EJEH

    2014-02-01

    Full Text Available An investigation into the production of biodiesel from shea butter oil using homogenous catalyst was carried out. The properties of the oil obtained were first determined, having an FFA value of 2.279 amongst other properties. Thus, the direct base-catalysis method was used, with potassium hydroxide as the catalyst. In a 1 hour batch run, biodiesel was produced with a conversion of 92%, FAME content of 97.1%, cetane number of 46.84 and kinematic viscosity of 4.30mm2/s, conforming to ASTM D6751 and EN 14214 international standards. As such, it was established that shea butter biodiesel could be produced by the direct base catalysis, over a shorter time with low cost chemicals.

  15. Proteomic analysis of the oil palm fruit mesocarp reveals elevated oxidative phosphorylation activity is critical for increased storage oil production.

    Science.gov (United States)

    Loei, Hendrick; Lim, Justin; Tan, Melvin; Lim, Teck Kwang; Lin, Qing Song; Chew, Fook Tim; Kulaveerasingam, Harikrishna; Chung, Maxey C M

    2013-11-01

    Palm oil is a highly versatile commodity with wide applications in the food, cosmetics, and biofuel industries. Storage oil in the oil palm mesocarp can make up a remarkable 80% of its dry mass, making it the oil crop with the richest oil content in the world. As such, there has been an ongoing interest in understanding the mechanism of oil production in oil palm fruits. To identify the proteome changes during oil palm fruit maturation and factors affecting oil yield in oil palm fruits, we examined the proteomic profiles of oil palm mesocarps at four developing stages--12, 16, 18, and 22 weeks after pollination--by 8-plex iTRAQ labeling coupled to 2D-LC and MALDI-TOF/TOF MS. It was found that proteins from several important metabolic processes, including starch and sucrose metabolism, glycolysis, pentose phosphate shunt, fatty acid biosynthesis, and oxidative phosphorylation, were differentially expressed in a concerted manner. These increases led to an increase in carbon flux and a diversion of resources such as ATP and NADH that are required for lipid biosynthesis. The temporal proteome profiles between the high-oil-yielding (HY) and low-oil-yielding (LY) fruits also showed significant differences in the levels of proteins involved in the regulation of the TCA cycle and oxidative phosphorylation. In particular, the expression level of the β subunit of the ATP synthase complex (complex IV of the electron transport chain) was found to be increased during fruit maturation in HY but decreased in the LY during the fruit maturation. These results suggested that increased energy supply is necessary for augmented oil yield in the HY oil palm trees.

  16. Structural level characterization of base oils using advanced analytical techniques

    KAUST Repository

    Hourani, Nadim

    2015-05-21

    Base oils, blended for finished lubricant formulations, are classified by the American Petroleum Institute into five groups, viz., groups I-V. Groups I-III consist of petroleum based hydrocarbons whereas groups IV and V are made of synthetic polymers. In the present study, five base oil samples belonging to groups I and III were extensively characterized using high performance liquid chromatography (HPLC), comprehensive two-dimensional gas chromatography (GC×GC), and Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) equipped with atmospheric pressure chemical ionization (APCI) and atmospheric pressure photoionization (APPI) sources. First, the capabilities and limitations of each analytical technique were evaluated, and then the availed information was combined to reveal compositional details on the base oil samples studied. HPLC showed the overwhelming presence of saturated over aromatic compounds in all five base oils. A similar trend was further corroborated using GC×GC, which yielded semiquantitative information on the compound classes present in the samples and provided further details on the carbon number distributions within these classes. In addition to chromatography methods, FT-ICR MS supplemented the compositional information on the base oil samples by resolving the aromatics compounds into alkyl- and naphtheno-subtituted families. APCI proved more effective for the ionization of the highly saturated base oil components compared to APPI. Furthermore, for the detailed information on hydrocarbon molecules FT-ICR MS revealed the presence of saturated and aromatic sulfur species in all base oil samples. The results presented herein offer a unique perspective into the detailed molecular structure of base oils typically used to formulate lubricants. © 2015 American Chemical Society.

  17. Determination of optimal parameters of purification water surface from oil and oil products by sorbent on the basis of worn automobile tires

    OpenAIRE

    YUSUBOV FAXRADDIN VALI; SHIXALIYEV КARAM SEYFI; ABDULLAYEVA МAYA YADIGAR

    2016-01-01

    The article describes an identification of optimal parameters for surface water purification from oil and oil products by sorbent based on worn automotive tires. In thus Optimal parameters for water surface purification from oil and oil products by sorbent have been found out on the basis of constructed regression model of the process.

  18. Contaminants, toxicity and wildlife mortality at oil production sites in western South Dakota

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Chemicals at oil production sites can be hazardous to migratory birds and other wildlife. Oil, grease, and other chemical wastes related to well drilling are...

  19. Production and refining of Dacryodes edulis “native pear” seeds oil

    African Journals Online (AJOL)

    STORAGESEVER

    2008-05-02

    May 2, 2008 ... when left in oil will result in the production of off flavours, odours and colours ... such as palm kernel (40%), peanuts (49%), cotton seed. (36%), and soybean ... resulted in acceleration of rate deterioration (rancidity) in the oil.

  20. Effect of Crude Oil Price on Agricultural Productivity in Nigeria (1981 ...

    African Journals Online (AJOL)

    SH

    ... 131-139, 2013 International Journal of Applied Agricultural and Apicultural Research ... rate, crude oil price, capital stock, labour, land and fertilizer. ... gross domestic product and accounting for ... the international oil market (Aigbedion and.

  1. Characterization of Bio-Oil: A By-Product from Slow Pyrolysis of Oil Palm Empty Fruit Bunches

    Directory of Open Access Journals (Sweden)

    K. H. Khor

    2009-01-01

    Full Text Available Problem statement: Oil palm Empty Fruit Bunches (EFB are abundant biomass in Malaysia. Studies about production of biofuels using slow pyrolysis of EFB are still lacking. So, this study was aimed to understand the physical and chemical properties of the bio-oil and its simple blends. Approach: EFB was slow pyrolysed with internal heating at terminal temperature of 600°C in a pilot kiln and the main product is the EFB char and the condensates from the emissions were separated into aqueous and tarry fractions. Results: 13 wt% of tarry component (referred as EFB oil was obtained as small fraction of co-product. The chemical composition of the EFB oil acquired was analyzed by GC-MS and its elemental composition, stability, miscibility, oil fuel properties and corrosion characteristics were determined. The empirical formula of the EFB oil with heating value of 31.44 MJ kg-1 was established as CH1.41N0.03O0.24. Characterizations of bio-oil, diesel and emulsifier blends were performed. Conclusion/Recommendations: The experimental results showed that the emulsions of EFB oil obtained may be directly used as a fuel oil for combustion in a boiler or a furnace without any upgrading. Alternatively, the fuel may be refined to be used by vehicles.

  2. PetroChina Upgrades Its Marketing System of Oil Products Nationwide

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    @@ PetroChina constructs large-scale storage depot for oil products in Shanghai PetroChina started to construct a large-scale oil depot at Waigaoqiao in Shanghai to facilitate its oil products flow in East China in the beginning of 2004. The storage capacity of the first stage is 300,000 cubic meters,110,000 cubic meters for diesel,90,000 cubic meters for gasoline and 100,000 cubic meters for other fuel oil.

  3. Distillation Parameters for Pilot Plant Production of Laurus nobilis Essential oil

    OpenAIRE

    2012-01-01

    Essential oils have increasing importance in flavour and fragrance industries. They are obtained by distillation techniques. In order to produce an oil with market potential its optimum production parameters have to be well known prior to its commercial production. Determination of the steam distillation parameters of commercially available Laurel leaves oil in pilot plant scale is described. The effect of steam rate and processing time play a major role in distillation of essential oils. Dis...

  4. 75 FR 20271 - Oil and Gas and Sulphur Operations in the Outer Continental Shelf-Oil and Gas Production...

    Science.gov (United States)

    2010-04-19

    ..., in OCS Order No. 11 in 1974, ] during a period of oil shortages and energy crises. In 1988, MMS... other oil and natural gas production data. The Department of Energy's Energy Information Administration... recommendation to the Secretary of Energy to consider consulting with EPA (Environmental Protection Agency),...

  5. Collective action in a smallholder oil palm production system in Indonesia: The key to sustainable and inclusive smallholder palm oil?

    NARCIS (Netherlands)

    Jelsma, Idsert; Slingerland, Maja; Giller, Ken E.; Bijman, Jos

    2017-01-01

    Indonesian smallholder oil palm generally yield much less than corporate plantations. We analysed a smallholder oil palm production system in West Sumatra which outperformed its nucleus estate plantation, consistently producing yields far above the national average for over 25 years. Its

  6. SENSITIVITY OF MOLDS ISOLATED FROM WAREHOUSES OF FOOD PRODUCTION FACILITY ON SELECTED ESSENTIAL OILS

    Directory of Open Access Journals (Sweden)

    Łukasz Kręcidło

    2015-07-01

    Full Text Available Storage of raw materials is one of steps in food production chain. The aim of this study was to estimate the influence of selected essential oils on the growth of four fungal strains: Trichoderma viride, Rhizomucor miehei, Penicillium chrysogenum, Penicillium janthinellum. Strains were isolated from warehouses of the food production facility. Selected essential oils: thyme oil, rosewood oil and rosemary oil were used to assess antifungal activity. Chemical composition of essential oils was determined by Gas Chromatography-Mass Spectroscopy (GC-MS. Antifungal activity of essential oils was estimated in relative to peracetic acid (PAA and sterile water with Tween 80 (0,5%. The influence of essential oils on fungal growth was carried by medium poisoning method. Increment of fungal mycelium was measured every day by 10 days. The thyme essential oils totally inhibited fungal growth in the lowest concentration of 1 mm3·cm-3. The most resistant strain was Penicillium janthinellum.

  7. Catalytic processes towards the production of biofuels in a palm oil and oil palm biomass-based biorefinery.

    Science.gov (United States)

    Chew, Thiam Leng; Bhatia, Subhash

    2008-11-01

    In Malaysia, there has been interest in the utilization of palm oil and oil palm biomass for the production of environmental friendly biofuels. A biorefinery based on palm oil and oil palm biomass for the production of biofuels has been proposed. The catalytic technology plays major role in the different processing stages in a biorefinery for the production of liquid as well as gaseous biofuels. There are number of challenges to find suitable catalytic technology to be used in a typical biorefinery. These challenges include (1) economic barriers, (2) catalysts that facilitate highly selective conversion of substrate to desired products and (3) the issues related to design, operation and control of catalytic reactor. Therefore, the catalytic technology is one of the critical factors that control the successful operation of biorefinery. There are number of catalytic processes in a biorefinery which convert the renewable feedstocks into the desired biofuels. These include biodiesel production from palm oil, catalytic cracking of palm oil for the production of biofuels, the production of hydrogen as well as syngas from biomass gasification, Fischer-Tropsch synthesis (FTS) for the conversion of syngas into liquid fuels and upgrading of liquid/gas fuels obtained from liquefaction/pyrolysis of biomass. The selection of catalysts for these processes is essential in determining the product distribution (olefins, paraffins and oxygenated products). The integration of catalytic technology with compatible separation processes is a key challenge for biorefinery operation from the economic point of view. This paper focuses on different types of catalysts and their role in the catalytic processes for the production of biofuels in a typical palm oil and oil palm biomass-based biorefinery.

  8. Raceways-based production of algal crude oil

    Energy Technology Data Exchange (ETDEWEB)

    Chisti, Yusuf [Massey Univ., Palmerston North (New Zealand). School of Engineering

    2013-11-01

    Raceway ponds, or 'high-rate algal ponds', of various configurations have been used to treat wastewater since the 1950s. They are also known as Oswald ponds after their inventor W. J. Oswald. Large-scale outdoor culture of microalgae and cyanobacteria in raceways is well established (Terry and Raymond 1985; Oswald 1988; Borowitzka and Borowitzka 1989; Becker 1994; Lee 1997; Molina Grima 1999; Pulz 2001; Borowitzka 2005; Spolaore et al. 2006). Raceway culture is used commercially in the United States, Thailand, China, Israel and elsewhere, mostly to produce algae for relatively high-value applications. This chapter is focused on raceways typically used in the production of algal biomass and not in the treatment of wastewater. The engineering design, operation and performance characteristics of raceways are discussed. The biomass productivity of the raceways is assessed in relation to limits imposed by algal biology. The economics of algal oil production in raceways are discussed. (orig.)

  9. Immobilization of Yarrowia lipolytica for aroma production from castor oil.

    Science.gov (United States)

    Braga, Adelaide; Belo, Isabel

    2013-04-01

    The main aim of this study was to compare different materials for Y. lipolytica immobilization that could be used in the production of γ-decalactone (a peach-like aroma) in order to prevent the toxic effect both of the substrate and the aroma upon the cells. Therefore, cells adsorption onto pieces of methyl polymethacrylate and of DupUM(®) was studied and further used in the biotransformation of castor oil into γ-decalactone. The highest aroma concentration was obtained with immobilized cells in DupUM(®), where reconsumption of the aroma by the cells was prevented, contrarily to what happens with free cells. This is a very promising result for γ-decalactone production, with potential to be used at an industrial level since the use of immobilized cells system will facilitate the conversion of a batch process into a continuous mode keeping high cell density and allowing easier recovery of metabolic products.

  10. Biodiesel production from waste frying oils and its quality control.

    Science.gov (United States)

    Sabudak, T; Yildiz, M

    2010-05-01

    The use of biodiesel as fuel from alternative sources has increased considerably over recent years, affording numerous environmental benefits. Biodiesel an alternative fuel for diesel engines is produced from renewable sources such as vegetable oils or animal fats. However, the high costs implicated in marketing biodiesel constitute a major obstacle. To this regard therefore, the use of waste frying oils (WFO) should produce a marked reduction in the cost of biodiesel due to the ready availability of WFO at a relatively low price. In the present study waste frying oils collected from several McDonald's restaurants in Istanbul, were used to produce biodiesel. Biodiesel from WFO was prepared by means of three different transesterification processes: a one-step base-catalyzed, a two-step base-catalyzed and a two-step acid-catalyzed transesterification followed by base transesterification. No detailed previous studies providing information for a two-step acid-catalyzed transesterification followed by a base (CH(3)ONa) transesterification are present in literature. Each reaction was allowed to take place with and without tetrahydrofuran added as a co-solvent. Following production, three different procedures; washing with distilled water, dry wash with magnesol and using ion-exchange resin were applied to purify biodiesel and the best outcome determined. The biodiesel obtained to verify compliance with the European Standard 14214 (EN 14214), which also corresponds to Turkish Biodiesel Standards.

  11. Noncatalytic biodiesel fuel production from croton megalocarpus oil

    Energy Technology Data Exchange (ETDEWEB)

    Kafuku, G.; Mbarawa, M. [Department of Mechanical Engineering, Tshwane University of Technology, Pretoria (South Africa); Tan, K.T.; Lee, K.T. [School of Chemical Engineering, Universiti Sains Malaysia, Engineering Campus, Seri Ampangan, Nibong Tebal, Pulau Pinang (Malaysia)

    2011-11-15

    Biodiesel is currently considered as the most promising substitute for diesel fuel because of its similar properties to diesel. This study presents the use of the supercritical methanol method in the production of biodiesel from Croton megalocarpus oil. The reaction parameters such as methanol-to-oil ratio, reaction temperature and reaction time were varied to obtain the optimal reaction conditions by design of experiment, specifically, response surface methodology based on three-variable central composite design with {alpha}=2. It has been shown that it is possible to achieve methyl ester yields as high as 74.91 % with reaction conditions such as 50:1 methanol-to-oil molar ratio, 330 C reaction temperature and a reaction period of 20 min. However, Croton-based biodiesel did not sustain higher temperatures due to decomposition of polyunsaturated methyl linoleate, which is dominant in biodiesel. Lower yields were observed when higher temperatures were used during the optimization process. The supercritical methanol method showed competitive biodiesel yields when compared with catalytic methods. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  12. Production of fatty alcohol from palm oil methyl ester

    Directory of Open Access Journals (Sweden)

    Tongurai, C.

    2007-05-01

    Full Text Available Fatty alcohol is an important raw material for the production of surfactants, and is currently in demand by markets and has a high potential for growth. Moreover, fatty alcohol can be made from methylester that is produced from fats and natural oil. The production of fatty alcohol involved hydrogenation using the suspension method process and methyl ester in palm oil as the raw material. Copper chromite was used as the catalyst for the hydrogenationreaction and the experiment was proceeded in a close system pressure reaction vessel. The reaction was conducted at approximately 150-250oC, 1100-1700 psig, 2-8% catalyst W/V of methyl ester and reaction timefrom 5-20 hr. After the reaction, the products were analysed to check for percent conversion using gas chromatography (GC. The hydrogenation reaction began at 200oC. The best hydrogenation reaction for theproduction of fatty alcohol occurred at 250oC, 1700 psig, 6% catalyst and reaction time of 20 hr, which gave a purity greater than 97%.

  13. Production of higher quality bio-oils by in-line esterification of pyrolysis vapor

    Science.gov (United States)

    Hilten, Roger Norris; Das, Keshav; Kastner, James R; Bibens, Brian P

    2014-12-02

    The disclosure encompasses in-line reactive condensation processes via vapor phase esterification of bio-oil to decease reactive species concentration and water content in the oily phase of a two-phase oil, thereby increasing storage stability and heating value. Esterification of the bio-oil vapor occurs via the vapor phase contact and subsequent reaction of organic acids with ethanol during condensation results in the production of water and esters. The pyrolysis oil product can have an increased ester content and an increased stability when compared to a condensed pyrolysis oil product not treated with an atomized alcohol.

  14. LOCATION OF IN TURKEY ECONOMIC OF OIL ROSE PRODUCTION IN ISPARTA REGION

    OpenAIRE

    Gökdoğan, Osman

    2013-01-01

    In this study, which has an important place in the world and Turkey economically oil rose "Rosa damascena Miller" macro and micro-economic point of view the importance of farming in the Isparta region are discussed. Perfumery, essential oil of roses in the world oil industry is important to the size of the role. The production konkret and rose oil from oil rose as well as by products for the production of rose water required in this study emphasizes the importance of making a rose o...

  15. State-of-the-art on ultrasonic oil production technique for EOR in China.

    Science.gov (United States)

    Wang, Zhenjun; Yin, Congbo

    2017-09-01

    Ultrasonic oil production technique for enhanced oil recovery (EOR) attracts more attention due to its high adaptability, simple operation, low cost and zero pollution to the oil reservoir. In this paper, recent new downhole tools used for enhanced oil recovery developed in China are summarized. Furthermore, research advance on some key problems that affect the widespread application of ultrasonic oil production technique in China are also summarized in view of what are the primary factors that influence crude oil paraffin inhibition and viscosity reduction, whether ultrasonic excitation is better than chemical agent for any plugs removal and whether ultrasound-chemical combination plug removal technology has the best plugs removal effect. The purpose of this paper is to provide reference for the broad application of ultrasonic oil production for enhance oil recovery. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. 1985 oil production of 21 oil producing non-OPEC countries

    Energy Technology Data Exchange (ETDEWEB)

    Warner, A.J.

    1979-03-01

    This report assesses the possibility of increased oil production from 21 less developed non-OPEC countries (excluding the Middle East and Mexico) by 1985. The forecast is compared with those prepared by the World Bank, the International Energy Agency, and others. The 21 Latin American, African, and Far East (including Asia) countries produce 2.5 million barrels of oil per day (BD) or 4.2% of world production, and they have 21 billion barrels of proved reserves, or 3.2% of the world total. In recent years these countries have consumed 3.1 million BD, some 0.9 million barrels in excess of their production. By 1985, the 21 countries may produce 3.9 million BD, an average annual increase of 5.0%; however, demand is expected to increase at an annual rate of 3.5% to 4.4 million BD. The net effect is that the 1985 aggregated supply-demand balance will be in deficit, by nearly 560 thousand BD, compared to slightly more than 930 thousand BD in 1976.

  17. Laboratory simulation of the successive aerobic and anaerobic degradation of oil products in oil-contaminated high-moor peat

    Science.gov (United States)

    Tolpeshta, I. I.; Trofimov, S. Ya.; Erkenova, M. I.; Sokolova, T. A.; Stepanov, A. L.; Lysak, L. V.; Lobanenkov, A. M.

    2015-03-01

    A model experiment has been performed on the successive aerobic and anaerobic degradation of oil products in samples of oil-contaminated peat sampled from a pine-subshrub-sphagnum bog near the Sutormin oilfield pipeline in the Yamal-Nenets autonomous district. During the incubation of oil-contaminated peat with lime and mineral fertilizers under complete flooding, favorable conditions are created for the aerobic oxidation of oil products at the beginning of the experiment and, as the redox potential decreases, for the anaerobic degradation of oil products conjugated with the reduction of N5+ and S+6 and methanogenesis. From the experimental data on the dynamics of the pH; Eh; and the NO{3/-}, NO{2/-}, and SO{4/2-} concentrations in the liquid phase of the samples, it has been found that denitrifiers significantly contributed to the biodegradation of oil products under the experimental conditions. After the end of the experiment, the content of oil products in the contaminated samples decreased by 21-26%.

  18. Productions of sunflower oil biodiesel and used cooking oil through heterogeneous catalysts compared to conventional homogeneous catalysts

    Science.gov (United States)

    Gutiérrez-Zapata, C. A.; Blanco Martínez, D.; Collazos, C. A.; Castellanos Acuña, H. E.; Cuervo, J. A.; Fernandez, C. P.

    2017-01-01

    This document compares homogeneous and heterogeneous catalysts used by production of biodiesel of sunflower oil and cooking oil used in frying. For this, NaOH was used as a catalyst homogeneous, and K2CO3 and Na2CO3 supported in gamma-alumina (K2CO3/γ Al2O3 y Na2CO3 /γ-Al2O3) were synthesized as heterogeneous catalysts, which were characterized by X-ray diffraction. The transesterification tests were carried out for the sunflower oil and used cooking oil, in a reflux system, to different molar relations methanol/oil, depending on the type of oil and characterization of the same. The reflux system is performed at a temperature of 55-60°C for one hour. Finally, biofuel was characterized and the yield of the reaction was calculated.

  19. PRODUCTION OF PALM OIL WITH METHANE AVOIDANCE AT PALM OIL MILL: A CASE STUDY OF CRADLE-TO-GATE LIFE CYCLE ASSESSMENT

    OpenAIRE

    Chiew Wei Puah; Yuen May Choo; Soon Hock Ong

    2013-01-01

    The study discusses a case study of cradle to gate life cycle assessment for the production of Crude Palm Oil (CPO) with methane avoidance at palm oil mill. The improved milling process enables total utilization of the oil palm fruit to produce alow oil palm based food source. The minimal modification in the mill includes cleaning of Fresh Fruit Bunches (FFB) and obtaining the low oil food source from the aqueous stream. The oil palm fruit processing plant enables the significant reduction of...

  20. Response surface methodology assisted biodiesel production from waste cooking oil using encapsulated mixed enzyme.

    Science.gov (United States)

    Razack, Sirajunnisa Abdul; Duraiarasan, Surendhiran

    2016-01-01

    In the recent scenario, consumption of petroleum fuels has increased to greater height which has led to deforestation and decline in fossil fuels. In order to tackle the perilous situation, alternative fuel has to be generated. Biofuels play a vital role in substituting the diesel fuels as they are renewable and ecofriendly. Biodiesel, often referred to as green fuel, could be a potential replacement as it could be synthesized from varied substrates, advantageous being the microalgae in several ways. The present investigation was dealt with the interesterification of waste cooking oil using immobilised lipase from mixed cultures for biodiesel production. In order to standardize the production for a scale up process, the parameters necessary for interesterification had been optimized using the statistical tool, Central Composite Design - Response Surface Methodology. The optimal conditions required to generate biodiesel were 2 g enzyme load, 1:12 oil to methyl acetate ratio, 60 h reaction time and 35 °C temperature, yielding a maximum of 93.61% biodiesel. The immobilised lipase beads remain stable without any changes in their function and structure even after 20 cycles which made this study, less cost intensive. In conclusion, the study revealed that the cooking oil, a residue of many dining centers, left as waste product, can be used as a potential raw material for the production of ecofriendly and cost effective biofuel, the biodiesel. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Life cycle assessment of a palm oil system with simultaneous production of biodiesel and cooking oil in Cameroon.

    Science.gov (United States)

    Achten, Wouter M J; Vandenbempt, Pieter; Almeida, Joana; Mathijs, Erik; Muys, Bart

    2010-06-15

    The use of palm oil as a biofuel has been heavily debated for its land-use conflict with nature and its competition with food production, being the number one cooking oil worldwide. In that context, we present a life cycle assessment of a palm oil production process yielding both biodiesel and cooking oil, incorporating the land-use impact and evaluating the effect of treating the palm oil mill effluent (POME) prior to disposal. The results show that the nonrenewable energy requirement, global warming potential (GWP; exclusive land-use change), and acidification potential are lower than those of the fossil alternative. However, the system triggers an increase in eutrophication potential (EP) compared to the fossil fuel reference. This system shows less energy requirement, global warming and acidification reduction, and less eutrophication increase compared to the reference than the same system converting all palm oil into biodiesel (no cooking oil production). The land occupation of palm oil triggers ecosystem quality (EQ) loss of 30-45% compared to the potential natural vegetation. Furthermore, such land-use change triggers a carbon debt neutralizing the GWP reduction for 45-53 years. The POME treatment scenarios reveal a trade-off between GWP and EP.

  2. Gamma-linolenic acid egg production enriched with hemp seed oil and evening primrose oil in diet of laying hens.

    Science.gov (United States)

    Park, Sang-Oh; Hwangbo, Jong; Yuh, In-Suh; Park, Byung-Sung

    2014-07-01

    This study was carried out to find out the effect of supplying gamma linolenic acid (GLA) on laying performance and egg quality. A hundred twenty of 30 weeks old hyline brown laying hens with 98% of egg production were completely randomized to 4 different treatment groups by 30 hens (the control group fed with the diet containing beef tallow, 3 treatment groups fed with the diet containing corn oil, the diet containing hemp seed oil and the diet containing evening primrose oil, respectively), and their laying performance and egg production were investigated for 5 weeks. Intake of hemp seed oil or evening primrose helped to increase the retention rate of GLA, which was transmigrated into eggs from blood. GLA was not detected in the blood samples of control group and treatment group fed diet containing corn oil, while it was significantly increased in the blood samples of the treatment groups fed with diet containing hemp seed oil and diet containing evening primrose oil, respectively. GLA retention was not observed in the eggs produced respectively by control group and treatment group fed with diet containing corn oil, whereas it was significantly increased in the eggs produced by the treatment group fed with diet containing hemp seed oil by 1.09% and the treatment group fed with diet containing evening primrose oil by 4.87%. This result suggests that GLA-reinforced functional eggs can be produced by adding hemp seed oil and evening primrose oil to the feed for laying hens and feeding them with it. It is thought that further researches and clinical trials on biochemical mechanism related to atopic dermatitis should be conducted in future.

  3. Gradient-based methods for production optimization of oil reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    Suwartadi, Eka

    2012-07-01

    Production optimization for water flooding in the secondary phase of oil recovery is the main topic in this thesis. The emphasis has been on numerical optimization algorithms, tested on case examples using simple hypothetical oil reservoirs. Gradientbased optimization, which utilizes adjoint-based gradient computation, is used to solve the optimization problems. The first contribution of this thesis is to address output constraint problems. These kinds of constraints are natural in production optimization. Limiting total water production and water cut at producer wells are examples of such constraints. To maintain the feasibility of an optimization solution, a Lagrangian barrier method is proposed to handle the output constraints. This method incorporates the output constraints into the objective function, thus avoiding additional computations for the constraints gradient (Jacobian) which may be detrimental to the efficiency of the adjoint method. The second contribution is the study of the use of second-order adjoint-gradient information for production optimization. In order to speedup convergence rate in the optimization, one usually uses quasi-Newton approaches such as BFGS and SR1 methods. These methods compute an approximation of the inverse of the Hessian matrix given the first-order gradient from the adjoint method. The methods may not give significant speedup if the Hessian is ill-conditioned. We have developed and implemented the Hessian matrix computation using the adjoint method. Due to high computational cost of the Newton method itself, we instead compute the Hessian-timesvector product which is used in a conjugate gradient algorithm. Finally, the last contribution of this thesis is on surrogate optimization for water flooding in the presence of the output constraints. Two kinds of model order reduction techniques are applied to build surrogate models. These are proper orthogonal decomposition (POD) and the discrete empirical interpolation method (DEIM

  4. GEOGRAPHIC INFORMATION SYSTEM APPROACH FOR PLAY PORTFOLIOS TO IMPROVE OIL PRODUCTION IN THE ILLINOIS BASIN

    Energy Technology Data Exchange (ETDEWEB)

    Beverly Seyler; John Grube

    2004-12-10

    Oil and gas have been commercially produced in Illinois for over 100 years. Existing commercial production is from more than fifty-two named pay horizons in Paleozoic rocks ranging in age from Middle Ordovician to Pennsylvanian. Over 3.2 billion barrels of oil have been produced. Recent calculations indicate that remaining mobile resources in the Illinois Basin may be on the order of several billion barrels. Thus, large quantities of oil, potentially recoverable using current technology, remain in Illinois oil fields despite a century of development. Many opportunities for increased production may have been missed due to complex development histories, multiple stacked pays, and commingled production which makes thorough exploitation of pays and the application of secondary or improved/enhanced recovery strategies difficult. Access to data, and the techniques required to evaluate and manage large amounts of diverse data are major barriers to increased production of critical reserves in the Illinois Basin. These constraints are being alleviated by the development of a database access system using a Geographic Information System (GIS) approach for evaluation and identification of underdeveloped pays. The Illinois State Geological Survey has developed a methodology that is being used by industry to identify underdeveloped areas (UDAs) in and around petroleum reservoirs in Illinois using a GIS approach. This project utilizes a statewide oil and gas Oracle{reg_sign} database to develop a series of Oil and Gas Base Maps with well location symbols that are color-coded by producing horizon. Producing horizons are displayed as layers and can be selected as separate or combined layers that can be turned on and off. Map views can be customized to serve individual needs and page size maps can be printed. A core analysis database with over 168,000 entries has been compiled and assimilated into the ISGS Enterprise Oracle database. Maps of wells with core data have been generated

  5. Aggregated services to the product of an equipment manufacturer of the oil industry: the PSS

    Directory of Open Access Journals (Sweden)

    Eduardo Magalhães Calvilho

    2014-08-01

    Full Text Available This article aims at analyzing the service operations that a manufacturer of equipment for the oil industry now offers together with their products, in order to maintain its position in a market in which technology is a competitive criterion. The research method is the case study. The integration between product and associated services is well suited described by PSS: Product-Service Systems. The research techniques were: analysis of industry-specific documents, semi-structured interviews, and non-participant observation in plant. Thirteen services which the manufacturer offers, associated with the product, gas turbines, where studied. The services were detailed and contextualized in industry and compared with theoretical elements found in the literature on PSS. Most services are based on the product and are offered as aftermarket activities. The study also describes expected economic and environmental gains.

  6. Product Structure, the Heart of Product Definition

    Science.gov (United States)

    DeHoog, C., Jr.

    1999-01-01

    This paper describes the LMMSS Product Definition System (PDS) philosophy and approach were the use of each item parts document or software can be traced to a specific end item (EI) serial/tail number of the product. It explains why a part-oriented approach to data organization and configuration management is required. The definition of part-oriented is that all appropriate product definition data products will be collected. Referenced and managed by their linkage/relationship to parts/items, The paper will touch upon how LMMSS store/controls product definition information under each project's top product designator in a two tiered approach. One tier for each product end item and another tier which contain/controls listings of drawings, documents. Specifications and standards that are required for hardware item definition.

  7. Production of haploids and doubled haploids in oil palm

    Directory of Open Access Journals (Sweden)

    Croxford Adam E

    2010-10-01

    Full Text Available Abstract Background Oil palm is the world's most productive oil-food crop despite yielding well below its theoretical maximum. This maximum could be approached with the introduction of elite F1 varieties. The development of such elite lines has thus far been prevented by difficulties in generating homozygous parental types for F1 generation. Results Here we present the first high-throughput screen to identify spontaneously-formed haploid (H and doubled haploid (DH palms. We secured over 1,000 Hs and one DH from genetically diverse material and derived further DH/mixoploid palms from Hs using colchicine. We demonstrated viability of pollen from H plants and expect to generate 100% homogeneous F1 seed from intercrosses between DH/mixoploids once they develop female inflorescences. Conclusions This study has generated genetically diverse H/DH palms from which parental clones can be selected in sufficient numbers to enable the commercial-scale breeding of F1 varieties. The anticipated step increase in productivity may help to relieve pressure to extend palm cultivation, and limit further expansion into biodiverse rainforest.

  8. Stress, seismicity and structure of shallow oil reservoirs of Clinton County, Kentucky. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hamilton-Smith, T. [Kentucky Geological Survey, Lexington, KY (United States)

    1995-12-12

    Between 1993 and 1995 geophysicists of the Los Alamos National Laboratory, in a project funded by the US Department of Energy, conducted extensive microseismic monitoring of oil production in the recently discovered High Bridge pools of Clinton County and were able to acquire abundant, high-quality data in the northern of the two pools. This investigation provided both three-dimensional spatial and kinetic data relating to the High Bridge fracture system that previously had not been available. Funded in part by the Los Alamos National Laboratory, the Kentucky Geological Survey committed to develop a geological interpretation of these geophysical results, that would be of practical benefit to future oils exploration. This publication is a summary of the results of that project. Contents include the following: introduction; discovery and development; regional geology; fractured reservoir geology; oil migration and entrapment; subsurface stress; induced seismicity; structural geology; references; and appendices.

  9. Crude Production Tops 2 Million Tons at Qinghai Oil Field

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    @@ The crude oil output of Qinghai Oil Field in Qaidam basin of the northwestern China's Qinghai Province topped two million tons at the end of 2000.This is the first time that the annual crude oil output of the oilfield has exceeded two millions, according to Huang Ligong, general manager of Qinghai Oil Field under PetroChina.

  10. China Oil Reserve and Major Refined Products Marketing Research

    Institute of Scientific and Technical Information of China (English)

    Yang Xunying

    2001-01-01

    @@ 1 Current Status and Forecast on Supply and Demand for Oil in China 1.1 Chinese oil trade balance China's demand for crude oil has increased sharply since the 1990's. From 1991 to 2000, the consumption of China's crude oil increased by 6% a year, but the output still lagged far behind the domestic need (See Table 1).

  11. Biofuel Production Using Butanol and Used Transformer Oil

    Directory of Open Access Journals (Sweden)

    J.Antony Pradeep

    2016-08-01

    Full Text Available Energy demand of the world increases tremendously. The use of fossil fuels to this extent makes it limited and it is an important cause for global warming. To reduce the emission of greenhouse gases and fossil fuel usage, many developments were made using renewable energy. Ethanol was used as a substitute for gasoline lately but it is highly corrosive and need separate tankers for transportation. Instead of using ethanol, butanol will give high mileage, less corrosive and has higher flash and boiling point than ethanol. In this project, biofuel is produced by transesterification of butanol and used transformer oil with KOH as catalyst. Glycerol is a by-product in this process. It can be used as a substrate for the microbial production of plastics and in anaerobic digestion.

  12. Biodiesel production from castor oil in Brazil: A difficult reality

    Energy Technology Data Exchange (ETDEWEB)

    Silva Cesar, Aldara da, E-mail: aldara@dep.ufscar.b [Federal University of Sao Carlos, Gepai - Grupo de Estudos e Pesquisas Agroindustriais, Departamento de Engenharia de Producao - UFSCar, Rodovia Washington Luis, km 235 - CEP 13565-905 - Sao Carlos - SP (Brazil); Otavio Batalha, Mario [Federal University of Sao Carlos, Gepai - Grupo de Estudos e Pesquisas Agroindustriais, Departamento de Engenharia de Producao - UFSCar, Rodovia Washington Luis, km 235 - CEP 13565-905 - Sao Carlos - SP (Brazil)

    2010-08-15

    The Brazilian National Program for Production and Use of Biodiesel (PNPB in Portuguese) has created a huge demand for biodiesel in Brazil. The PNPB is strongly based on social development through the inclusion of family farmers in projects integrated with biodiesel power plants. Among the various oilseeds, castor bean (Ricinus communis L.) was identified as the ideal one to promote social development in the semi-arid region. However, although promising, the mechanisms of the federal program are still insufficient to promote the effective participation of family farmers. This research shows that companies are facing huge problems in implementing contracts with family farmers. It describes and analyzes the functioning dynamics of this agro-production chain. This paper addresses the identification and the discussion of these obstacles, in order to increase the competitiveness of the biodiesel agribusiness chain, based on castor oil social projects in Brazil.

  13. Biodiesel production from castor oil in Brazil. A difficult reality

    Energy Technology Data Exchange (ETDEWEB)

    Silva Cesar, Aldara da; Otavio Batalha, Mario [Federal University of Sao Carlos, Gepai - Grupo de Estudos e Pesquisas Agroindustriais, Departamento de Engenharia de Producao - UFSCar, Rodovia Washington Luis, km 235 - CEP 13565-905 - Sao Carlos (Brazil)

    2010-08-15

    The Brazilian National Program for Production and Use of Biodiesel (PNPB in Portuguese) has created a huge demand for biodiesel in Brazil. The PNPB is strongly based on social development through the inclusion of family farmers in projects integrated with biodiesel power plants. Among the various oilseeds, castor bean (Ricinus communis L.) was identified as the ideal one to promote social development in the semi-arid region. However, although promising, the mechanisms of the federal program are still insufficient to promote the effective participation of family farmers. This research shows that companies are facing huge problems in implementing contracts with family farmers. It describes and analyzes the functioning dynamics of this agro-production chain. This paper addresses the identification and the discussion of these obstacles, in order to increase the competitiveness of the biodiesel agribusiness chain, based on castor oil social projects in Brazil. (author)

  14. Options to reduce environmental impacts of palm oil production in Thailand

    NARCIS (Netherlands)

    Saswattecha, Kanokwan; Kroeze, Carolien; Jawjit, Warit; Hein, Lars

    2016-01-01

    There is an increasing demand for palm oil worldwide. In Thailand, oil palm is being promoted by the government but this expansion is associated with several environmental impacts. We identified 26 options for reducing the environmental impact of palm oil production in Thailand, and assessed their c

  15. Non-Edible Plant Oils as New Sources for Biodiesel Production

    Directory of Open Access Journals (Sweden)

    M. Rafiqul Islam

    2008-02-01

    Full Text Available Due to the concern on the availability of recoverable fossil fuel reserves and the environmental problems caused by the use those fossil fuels, considerable attention has been given to biodiesel production as an alternative to petrodiesel. However, as the biodiesel is produced from vegetable oils and animal fats, there are concerns that biodiesel feedstock may compete with food supply in the long-term. Hence, the recent focus is to find oil bearing plants that produce non-edible oils as the feedstock for biodiesel production. In this paper, two plant species, soapnut (Sapindus mukorossi and jatropha (jatropha curcas, L. are discussed as newer sources of oil for biodiesel production. Experimental analysis showed that both oils have great potential to be used as feedstock for biodiesel production. Fatty acid methyl ester (FAME from cold pressed soapnut seed oil was envisaged as biodiesel source for the first time. Soapnut oil was found to have average of 9.1% free FA, 84.43% triglycerides, 4.88% sterol and 1.59% others. Jatropha oil contains approximately 14% free FA, approximately 5% higher than soapnut oil. Soapnut oil biodiesel contains approximately 85% unsaturated FA while jatropha oil biodiesel was found to have approximately 80% unsaturated FA. Oleic acid was found to be the dominant FA in both soapnut and jatropha biodiesel. Over 97% conversion to FAME was achieved for both soapnut and jatropha oil.

  16. Challenges of Membrane Filtration for Produced Water Treatment in Offshore Oil & Gas Production

    DEFF Research Database (Denmark)

    Jepsen, Kasper Lund; Hansen, Leif; Mai, Christian

    2016-01-01

    Tremendous amount of produced water are discharged into the sea from offshore oil & gas installations. Along with every barrel of oil three barrels of water are produced and this is only worsen as the fields mature. Enhanced oil recovery (EOR) is employed to increase production, as a part of EOR...

  17. 15 CFR 754.3 - Petroleum products not including crude oil.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Petroleum products not including crude... SUPPLY CONTROLS § 754.3 Petroleum products not including crude oil. (a) License requirement. As indicated... required to all destinations, including Canada, for the export of petroleum products, excluding crude oil...

  18. Multi-Agents in the North Sea – The Case of Oil and Gas Production

    DEFF Research Database (Denmark)

    Mikkelsen, Lars Lindegaard; Demazeau, Yves; Jørgensen, Bo Nørregaard

    2011-01-01

    Developing control systems for offshore oil and gas production is a challenging task, due to the complex inherent issues of the domain, i.e. changing properties of the oil and gas reservoirs, and variations in production configuration, due to new wells and production technologies. In this paper, we...

  19. PetroChina Sees Stable Oil Production Growth in 1st Half of 2001

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    @@ By the end of June 2001, PetroChina completed 50.26 percent of the annual crude production. It has decided to add 700,000 tons to the original crude production. The daily oil production at 13 oil fields under PetroChina was on the gradual increase in the first half of the year.

  20. Production of free fatty acids from waste oil by application of ultrasound

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Larissa P.; Santos, Francisco F.P.; Costa, Enio; Fernandes, Fabiano A.N. [Universidade Federal do Ceara, Departamento de Engenharia Quimica, Fortaleza, CE (Brazil)

    2012-12-15

    This paper evaluates the production of free fatty acids (FFAs) from waste oil by means of low-frequency high-intensity ultrasound application under atmospheric pressure. To evaluate the potential of this technology, the reaction between waste palm oil and ethanol was carried out. Response surface methodology (RSM) was used to evaluate the influence of alcohol-to-oil weight ratio, potassium hydroxide-to-oil weight ratio, and temperature on the yield of waste oil into FFA. Analysis of the operating conditions by RSM showed that the most important operating conditions affecting the reaction were ethanol-to-oil weight ratio and potassium hydroxide-to-oil weight ratio. The highest yield observed was of 97.3 % after 45 min of reaction. The best operating condition was obtained by applying an ethanol-to-oil weight ratio of 2.4, a potassium hydroxide-to-oil weight ratio of 0.3, and temperature of 60 C. (orig.)

  1. Catalytic conversion of palm oil over mesoporous aluminosilicate MCM-41 for the production of liquid hydrocarbon fuels

    Energy Technology Data Exchange (ETDEWEB)

    Twaiq, Farouq A.; Mohamed, Abdul Rahman; Bhatia, Subhash [School of Chemical Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, SPS, Pinang (Malaysia); Zabidi, Noor Asmawati M. [Universiti Teknologi Petronas, Sri Iskandar, 31750 Tronoh, Perak (Malaysia)

    2003-11-15

    The catalytic cracking of palm oil to liquid hydrocarbon fuels was studied in a fixed bed micro-reactor operated at atmospheric pressure, reaction temperature of 723 K and weight hourly space velocity (WHSV) of 2.5 h{sup -1} over the synthesized mesoporous molecular sieve MCM-41 materials. Mesoporous aluminosilicate with Si/Al ratio of 50 was synthesized using the hydrothermal method. Different pore sizes were obtained by changing the type of template and organic directing agent (ODA) used. The synthesized materials were characterized using various analytical methods such as X-ray powder diffraction (XRD), BET surface area, inductive coupled plasma (ICP), MAS NMR, FTIR and temperature-programmed desorption (TPD). The materials exhibit a crystalline structure of MCM-41 mesoporous molecular sieves with surface area varying from 550 to 1200 m{sup 2}/g and an average pore size (APS) ranging from 1.8 to 2.8 nm. The synthesized MCM-41 catalysts show high activity for palm oil cracking. The conversion of palm kernel oil, lower-molecular-weight oil, was higher as compared to higher-molecular-weight, palm olein oil. MCM-41 materials were selective for the formation of linear hydrocarbons, particularly, C{sub 13} when palm kernel oil was used and C{sub 17} when palm olein oil was fed. The yield of liquid product decreased with the increase of surface area of the catalyst. The gasoline selectivity increased whereas diesel selectivity decreased with the conversion of palm oil.

  2. How to Adjust XPCC’s Planting Structure of Grain,Cotton,Oil and Sugar?

    Institute of Scientific and Technical Information of China (English)

    Xin; ZHANG; Gang; WANG; Guodong; WANG; Fei; LIANG

    2015-01-01

    XPCC has long shouldered the mission of exploitation of virgin land in border area,but the special geographic distribution leads to regional segmentation and administrative division in the planting structure of grain,cotton,oil and sugar for XPCC. Since 1980,XPCC’s total planting area of grain,cotton,oil and sugar has increased steadily year by year. The yield levels show a unimodal trend; the total yield of cotton has been showing a geometric growth trend; the total yield of oil crops and sugar beet shows a fluctuating growth trend,but the total yield of grain crops shows a bimodal growth trend. XPCC’s grain crops are mainly in the farms of Division 4 in Ili Valley and Division 6 in Changji;cotton production in South and North Xinjiang is basically the same,and the yield in South Xinjiang is slightly higher than in North Xinjiang,but cotton can not be planted in most farms of Division 9 and Division 10; oil crops are grown mainly in cold regions; sugar beet is mainly in the farms of Division 2,Division 4,Division 7 and Division 9. Some factors are limiting XPCC’s farming development such as unreasonable agricultural structure,quite different regional production levels and great grain crop yield fluctuations. Therefore,it is recommended to optimize regional distribution,increase efforts to promote new technologies,and strengthen brand building to help XPCC to give play to the agricultural resource advantages.

  3. The overlaying oil type influences in vitro embryo production: differences in composition and compound transfer into incubation medium between oils.

    Science.gov (United States)

    Martinez, Cristina A; Nohalez, Alicia; Parrilla, Inmaculada; Motas, Miguel; Roca, Jordi; Romero, Inmaculada; García-Gonza Lez, Diego L; Cuello, Cristina; Rodriguez-Martinez, Heriberto; Martinez, Emilio A; Gil, Maria A

    2017-09-05

    The oil overlay micro-drop system is widely used for cultures of mammalian gametes and embryos. We evaluated hereby the effects of two unaltered commercial oils- Sigma mineral oil (S-MO) and Nidoil paraffin oil (N-PO)-on in vitro embryo production (IVP) outcomes using a pig model. The results showed that while either oil apparently did not affect oocyte maturation and fertilization rates, S-MO negatively affected embryo cleavage rates, blastocyst formation rates, and, consequently, total blastocyst efficiency of the system. No differences in the oxidation state were found between the oils or culture media incubated under S-MO or N-PO. Although both oils slightly differed in elemental composition, there were no differences in the concentrations of elements between fresh media and media incubated under oils. By contrast, we demonstrated clear oil-type differences in both the composition of volatile organic compounds (VOC) and the transfer of some of these VOC´s (straight-chain alkanes and pentanal and 1,3-diethyl benzene) to the culture medium, which could have influenced embryonic development.

  4. Results of the International Energy Agency Round Robin on Fast Pyrolysis Bio-oil Production

    Energy Technology Data Exchange (ETDEWEB)

    Elliott, Douglas C.; Meier, Dietrich; Oasmaa, Anja; van de Beld, Bert; Bridgwater, Anthony V.; Marklund, Magnus

    2017-04-06

    An international round robin study of the production of fast pyrolysis bio-oil was undertaken. Fifteen institutions in six countries contributed. Three biomass samples were distributed to the laboratories for processing in fast pyrolysis reactors. Samples of the bio-oil produced were transported to a central analytical laboratory for analysis. The round robin was focused on validating the pyrolysis community understanding of production of fast pyrolysis bio-oil by providing a common feedstock for bio-oil preparation. The round robin included: •distribution of 3 feedstock samples from a common source to each participating laboratory; •preparation of fast pyrolysis bio-oil in each laboratory with the 3 feedstocks provided; •return of the 3 bio-oil products (minimum 500 ml) with operational description to a central analytical laboratory for bio-oil property determination. The analyses of interest were: density, viscosity, dissolved water, filterable solids, CHN, S, trace element analysis, ash, total acid number, pyrolytic lignin, and accelerated aging of bio-oil. In addition, an effort was made to compare the bio-oil components to the products of analytical pyrolysis through GC/MS analysis. The results showed that clear differences can occur in fast pyrolysis bio-oil properties by applying different reactor technologies or configurations. The comparison to analytical pyrolysis method suggested that Py-GC/MS could serve as a rapid screening method for bio-oil composition when produced in fluid-bed reactors. Furthermore, hot vapor filtration generally resulted in the most favorable bio-oil product, with respect to water, solids, viscosity, and total acid number. These results can be helpful in understanding the variation in bio-oil production methods and their effects on bio-oil product composition.

  5. THE DEVELOPMENT OF OIL AND GAS PRODUCTION GATHERING AND TRANSPORTATION TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    Mirko Zelić

    1990-12-01

    Full Text Available The oil production was started in 1945 to cover several small capacity oil fields and to expand in the forthcoming forty-five years to the wider area of the Northern Croatia. Significant exploration efforts and enthusiasm revealed perspective hydrocarbon layers on which a complex technological infrastructure was constructed (wells, technological systems, transportation systems for the purpose of oil and gas production, its processing and transportation to refineries and consumers. In line with development of other technoligies in the world, the oil and gas production and gathering technologies in INA - Naftaplin were also up—graded, monitoring and adopting the most advanced world achievements in the field of oil and gas production. Presently applied technology ranks INA - Naftaplin among modernly organized (from the technical and technologica point of view companies, engaged in the field of oil and gas production and processing (the paper is published in Croatian.

  6. POLY(3-HYDROXYBUTYRATE PRODUCTION BY Cupriavidus necator SUPPLEMENTED WITH MINIEMULSIFIED SOYBEAN OIL

    Directory of Open Access Journals (Sweden)

    M. Schmidt

    Full Text Available Abstract Studies have shown that the supplementation of vegetable oils, in poly(3-hydroxybutyrate production, provides an increase in the process productivity, besides inducing lipase activity in the medium. The supplementation with miniemulsified oils could potentialize these results. In this work, the influence of supplementation of the medium with soybean oil, without treatment and miniemulsified, on polymerr production was evaluated. The best moment to supplement the medium and its influence on lipase activity were also analyzed. The results showed that the supplementation with miniemulsified soybean oil promoted an increase of 9.7% in polymer content and the productivity increased from 0.58 to 0.63 g.L-1.h-1, when compared with the culture without supplementation. The best time to add the supplement is in the beginning of the production phase. The lipase activity was higher for the culture supplemented with miniemulsified soybean oil, promoting the use of the oil.

  7. Studying and optimizing the biodiesel production from mastic oil aided by ultrasonic using response surface method

    OpenAIRE

    B Hosseinzdeh Samani; E Fayyazi; B. Ghobadian; Rostami, S.

    2016-01-01

    Introduction Biodiesel is a promising renewable substitute source of fuel produced from tree born oils, vegetable based oils, fats of animals and even waste cooking oil, has been identified as one of the key solutions for the alarming global twin problems of fossil fuel depletion and environmental degradation. One of the sources for biodiesel production is mastic which is often grown in mountains. Its kernel contains 55% oil which makes it as a valuable renewable resource for biodiesel pro...

  8. Microbial production of polyhydroxyalkanoates by bacteria isolated from oil wastes.

    Science.gov (United States)

    Wong, A L; Chua, H; Yu, P H

    2000-01-01

    A Gram-positive coccus-shaped bacterium capable of synthesizing higher relative molecular weight (M(r)) poly-hydroxybutyrate (PHB) was isolated from sesame oil and identified as Staphylococcus epidermidis (by Microbial ID, Inc., Newark, NJ). The experiment was conducted by shake flask fermentation culture using media containing fructose. Cell growth up to a dry mass of 2.5 g/L and PHB accumulation up to 15.02% of cell dry wt was observed. Apart from using single carbohydrate as a sole carbon source, various industrial food wastes including sesame oil, ice cream, malt, and soya wastes were investigated as nutrients for S. epidermidis to reduce the cost of the carbon source. As a result, we found that by using malt wastes as nutrient for cell growth, PHB accumulation of S. epidermidis was much better than using other wastes as nutrient source. The final dried cell mass and PHB production using malt wastes were 1.76 g/L and 6.93% polymer/cells (grams/gram), and 3.5 g/L and 3.31% polymer/cells (grams/gram) in shake flask culture and in fermentor culture, respectively. The bacterial polymer was characterized by 1H-nuclear magnetic resonance (NMR), 13C-NMR, Fourier transform infrared, and differential scanning calorimetry. The results show that with different industrial food wastes as carbon and energy sources, the same biopolymer (PHB) was obtained. However, the use of sesame oil as the carbon source resulted in the accumulation of PHB with a higher melting point than that produced from other food wastes as carbon sources by this organism under similar experimental conditions.

  9. The implications of the declining energy return on investment of oil production.

    Science.gov (United States)

    Murphy, David J

    2014-01-13

    Declining production from conventional oil resources has initiated a global transition to unconventional oil, such as tar sands. Unconventional oil is generally harder to extract than conventional oil and is expected to have a (much) lower energy return on (energy) investment (EROI). Recently, there has been a surge in publications estimating the EROI of a number of different sources of oil, and others relating EROI to long-term economic growth, profitability and oil prices. The following points seem clear from a review of the literature: (i) the EROI of global oil production is roughly 17 and declining, while that for the USA is 11 and declining; (ii) the EROI of ultra-deep-water oil and oil sands is below 10; (iii) the relation between the EROI and the price of oil is inverse and exponential; (iv) as EROI declines below 10, a point is reached when the relation between EROI and price becomes highly nonlinear; and (v) the minimum oil price needed to increase the oil supply in the near term is at levels consistent with levels that have induced past economic recessions. From these points, I conclude that, as the EROI of the average barrel of oil declines, long-term economic growth will become harder to achieve and come at an increasingly higher financial, energetic and environmental cost.

  10. Bio-oil production via subcritical hydrothermal liquefaction of biomass

    Science.gov (United States)

    Durak, Halil

    2017-04-01

    Biomass based raw materials can be converted into the more valued energy forms using biochemical methods such as ethanol fermentation, methane fermentation and the thermochemical methods such as direct combustion, pyrolysis, gasification, liquefaction. The bio-oil obtained from the biomass has many advantages than traditional use. Firstly, it has features such as high energy density, easy storage and easy transportation. Bio-oil can be used as a fuel in engines, turbines and burning units directly. Besides, it can be converted into products in higher quality and volume via catalytic cracking, hydrodexygenation, emulsification, and steam reforming [1,2]. Many organic solvents such as acetone, ethanol, methanol, isopropanol are used in the supercritical liquefaction processes. When we think about the cost and effects of the organic solvent on nature, it will be understood better that it is necessary to find solvent that are more sensitive against nature. Here, water must have an important place because of its features. Most important solvent of the world water is named as "universal solvent" because none of the liquids can dissolve the materials as much as done by water. Water is found much at the nature and cost of it is very few when compared with the other solvent. Hydrothermal liquefaction, a thermochemical conversion process is an effective method used for converting biomass into the liquid products. General reaction conditions for hydrothermal liquefaction process are the 250-374 °C temperature range and 4 - 22 Mpa pressure values range, besides, the temperature values can be higher according to the product that is expected to be obtained [3,4]. In this study, xanthium strumarium plant stems have been used as biomass source. The experiments have been carried out using a cylindrical reactor (75 mL) at the temperatures of 300 °C. The produced liquids at characterized by elemental analysis, GC-MS and FT-IR. According to the analysis, different types of compounds

  11. Exopolysaccharide production by a genetically engineered Enterobacter cloacae strain for microbial enhanced oil recovery.

    Science.gov (United States)

    Sun, Shanshan; Zhang, Zhongzhi; Luo, Yijing; Zhong, Weizhang; Xiao, Meng; Yi, Wenjing; Yu, Li; Fu, Pengcheng

    2011-05-01

    Microbial enhanced oil recovery (MEOR) is a petroleum biotechnology for manipulating function and/or structure of microbial environments existing in oil reservoirs for prolonged exploitation of the largest source of energy. In this study, an Enterobacter cloacae which is capable of producing water-insoluble biopolymers at 37°C and a thermophilic Geobacillus strain were used to construct an engineered strain for exopolysaccharide production at higher temperature. The resultant transformants, GW3-3.0, could produce exopolysaccharide up to 8.83 g l(-1) in molasses medium at 54°C. This elevated temperature was within the same temperature range as that for many oil reservoirs. The transformants had stable genetic phenotype which was genetically fingerprinted by RAPD analysis. Core flooding experiments were carried out to ensure effective controlled profile for the simulation of oil recovery. The results have demonstrated that this approach has a promising application potential in MEOR. Copyright © 2011 Elsevier Ltd. All rights reserved.

  12. The influence of animal fat replacement with vegetable oils on sensorial perception of meat emulsified products

    Directory of Open Access Journals (Sweden)

    Cristian TUDOSE

    2014-12-01

    Full Text Available For the purpose of the present study, in an emulsified meat product the pork backfat was replaced with a vegetable oil pre-emulsion and its effect on quality attributes were investigated. In order to do so, a classic and a new meat products were manufactured. Extra virgin olive oil and palm oil pre-emulsion were added instead of animal fat in the new product. Texture and physiochemical properties were analyzed by instrumental measurements. It was observed that during storage moisture and pH decreased. Using vegetable oils determined substantial increase of TBA values. Texture was influenced mainly by storage time for both products, while replacement of pork backfat with vegetable oil pre-emulsion had no influence on sample firmness. The sensory properties of meat products were evaluated by a group of trained panelists using an analitycal sensory evaluation technique. Overall the new product presented good acceptability which recommends it like a new healthier meat product.

  13. Structure of pre-Caspian depression and major oil and gas fields of the region

    Energy Technology Data Exchange (ETDEWEB)

    Krylov, N.A. (Amoco Production Co., Houston, TX (United States)); Avrov, V.P. (Igirgi, Moscow (USSR)); Lisovsky, N.N.

    1991-03-01

    As a single unified depression, the pre-Caspian basin has been formed from Paleozoic to Cenozoic time. The basin is superimposed on two large pre-Permian depressions. On the Astrakhan-Aktyubinsk zone of uplifts between them is found sharply reduced Carboniferous and Devonian sections. Modern structural plan clearly displays two major structural stages: Subsalt (Paleozoic) and post (post-Kungurian). The post-salt stage is characterized by wide development of salt dome tectonics. It corresponds with its own petroliferous stage containing numerous, mostly small oil accumulations in terrigenous Mesozoic reservoirs. Large recent discoveries-Astrakhan condensate, Karachaganak and Kanazhol-Sinelnikov oil/condensate, Tengiz oil, and other fields-are associated with the Subsalt Paleozoic complex ranging from Lower Permian to the top of Upper Devonian. The Subsalt stage has its own regularities in hydrocarbon phase differentiation; large reserves concentration; dominantly productive carbonates with various reservoirs; and presence of structural, depositional, and erosional factors controlling formation of oil and gas traps. The paper describes major distributional features of the various arc-and-type Permian and Carboniferous formations, which in conjunction with Subsalt paleotemperature data and geochemistry of organic matter represents a basis for the forecast of new discoveries.

  14. The impact of Hurricanes Gustav and Ike on offshore oil and gas production in the Gulf of Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Kaiser, Mark J.; Yu, Yunke [Center for Energy Studies, Louisiana State University, Energy Coast and Environment Building, Nicholson Extension Drive, Baton Rouge, LA 70803 (United States)

    2010-01-15

    During August and September 2008, Hurricanes Gustav and Ike passed through the Gulf of Mexico and damaged and destroyed a number of offshore oil and gas structures. In the final official government assessment, a total of 60 platforms were destroyed and 31 structures were identified as having extensive damage. The destroyed platforms were responsible for about 1.6% of the oil and 2.5% of the gas produced daily in the Gulf of Mexico and represented approximately 234 million BOE of reserves valued between 4.6 and 10.9 billion. Although the number of structures destroyed by Hurricanes Gustav and Ike was half the total destruction from the 2004-2005 hurricane seasons, we estimate that the reserves at risk are approximately three times more valuable. Each destroyed structure is unique in its production capacity and damages incurred and are a candidate for redevelopment. We review pre-hurricane production and revenue characteristics for the collection of destroyed structures and estimate production at risk. Gas structures are expected to present better economics and redevelopment potential than oil structures, and we predict that 198 million BOE, or nearly 95% of reserves-in-place, are likely to be redeveloped. Shut-in production statistics are compared against recent hurricane events and general comments on the factors involved in decision making are presented. (author)

  15. Benzene exposure on a crude oil production vessel

    Energy Technology Data Exchange (ETDEWEB)

    Kirkeleit, J; Riise, T.; Bratveit, M.; Moen, B.E. [University of Bergen (Norway). Dept. of Public Health and Primary Health Care

    2006-07-01

    Objectives: The aim was to describe the personal exposure to benzene on a typical crude oil production vessel and to identify factors influencing the exposure level. Methods: The study population included process operators, deck workers, mechanics and contractors on a production vessel in the Norwegian sector of the North Sea. The personal exposure to benzene during ordinary activity, during a short shutdown and during tank work was monitored using organic vapour passive dosimeter badges (3MTM3500). Information on the tasks performed on the day of sampling was recorded. Exposure was assessed by grouping the measurements according to job category, mode of operation and the tasks performed on the sampling day. Univariate analysis of variance was used to test the differences between the groups. Results: Forty-two workers participated in the exposure assessment, comprising a total of 139 measurements. The arithmetic and geometric mean of benzene exposure for all measurements was 0.43 and 0.02 p.p.m., respectively. Twenty-five measurements (18%) were below the limit of detection (0.001 p.p.m.), while ten samples (7%) exceeded the occupational exposure limit of 0.6 p.p.m. The geometric mean exposure was 0.004 p.p.m. (95% CI 0.003-0.006) during ordinary activity, 0.01 p.p.m. (95% CI 0.005-0.02) during shutdown and 0.28 p.p.m. (95% CI 0.16-0.49) during tank work. Workers performing annual cleaning and maintenance of tanks containing crude oil or residues of crude oil had higher levels of exposure than workers performing other tasks, including work near open hydrocarbon-transport systems (all P < 0.001). However, because of the mandatory use of respirators, the actual personal benzene exposure was lower. The job categories explained only 5% of the variance in exposure, whereas grouping by mode of operation explained 54% of the variance and grouping by task 68%. Conclusion: The results show that, although benzene exposure during ordinary and high activity seems to be low in

  16. Hydrogen production from palm oil mill effluent by fermentation

    Energy Technology Data Exchange (ETDEWEB)

    Tanisho, S.; Shimazaki, T. [Yokohama National Univ., Shigeharu TANISHO and Tsuruyo SHIMAZAKI, Yokohama (Japan)

    2003-09-01

    Hydrogen production by fermentation was examined by using palm oil mill effluent. Clostridium butyricum produced more than 2.2 NL of hydrogen from 1 L of raw POME at pH 5.0, and Enterobacter aerogenes produced ca. 1.9 NL at pH 6.0. While from the culture liquid added 1% of peptone on the raw POME, C. butyricum produced more than 3.3 NL and also E. aerogenes 3.4 NL at pH 6.0 and 5.0, respectively. In this manner, the addition of nitrogen source to the POME liquid exerted an influence on the volume of hydrogen production. Since Aspergillus niger has ability to produce cellulase, co-cultivation of C.butyricum with A. niger was tried to utilize celluloses in the POME. Against our expectations, however, the results were lower productivities than pure cultivation's. We analyzed the components of POME by liquid chromatography and capillary electrophoresis before and after cultivation. The main substrate for hydrogen production was found to be glycerol. (authors)

  17. Robotics and automation for oil sands bitumen production and maintenance

    Energy Technology Data Exchange (ETDEWEB)

    Lipsett, M.G. [Alberta Univ., Edmonton, AB (Canada). Dept. of Mechanical Engineering

    2008-07-01

    This presentation examined technical challenges and commercial challenges related to robotics and automation processes in the mining and oil sands industries. The oil sands industry has on-going cost pressures. Challenges include the depths to which miners must travel, as well as problems related to equipment reliability and safety. Surface mines must operate in all weather conditions with a variety of complex systems. Barriers for new technologies include high capital and operating expenses. It has also proven difficult to integrate new technologies within established mining practices. However, automation has the potential to improve mineral processing, production, and maintenance processes. Step changes can be placed in locations that are hazardous or inaccessible. Automated sizing, material, and ventilation systems are can also be implemented as well as tele-operated equipment. Prototypes currently being developed include advanced systems for cutting; rock bolting; loose rock detection systems; lump size estimation; unstructured environment sensing; environment modelling; and automatic task execution. Enabling technologies are now being developed for excavation, haulage, material handling systems, mining and reclamation methods, and integrated control and reliability. tabs., figs.

  18. Thermoeconomic Analysis of Biodiesel Production from Used Cooking Oils

    Directory of Open Access Journals (Sweden)

    Emilio Font de Mora

    2015-05-01

    Full Text Available Biodiesel from used cooking oil (UCO is one of the most sustainable solutions to replace conventional fossil fuels in the transport sector. It can achieve greenhouse gas savings up to 88% and at the same time reducing the disposal of a polluting waste. In addition, it does not provoke potential negative impacts that conventional biofuels may eventually cause linked to the use of arable land. For this reason, most policy frameworks favor its consumption. This is the case of the EU policy that double-counters the use of residue and waste use to achieve the renewable energy target in the transport sector. According to different sources, biodiesel produced from UCO could replace around 1.5%–1.8% of the EU-27 diesel consumption. This paper presents an in-depth thermoeconomic analysis of the UCO biodiesel life cycle to understand its cost formation process. It calculates the ExROI value (exergy return on investment and renewability factor, and it demonstrates that thermoeconomics is a useful tool to assess life cycles of renewable energy systems. It also shows that UCO life cycle biodiesel production is more sustainable than biodiesel produced from vegetable oils.

  19. Marine Mammal Train Oil Production Methods: Experimental Reconstructions of Norwegian Iron Age Slab-Lined Pits

    Science.gov (United States)

    Nilsen, Gørill

    2016-08-01

    Seal hunting and whaling have played an important part of people's livelihoods throughout prehistory as evidenced by rock carvings, remains of bones, artifacts from aquatic animals and hunting tools. This paper focuses on one of the more elusive resources relating to such activities: marine mammal blubber. Although marine blubber easily decomposes, the organic material has been documented from the Mesolithic Period onwards. Of particular interest in this article are the many structures in Northern Norway from the Iron Age and in Finland on Kökar, Åland, from both the Bronze and Early Iron Ages in which these periods exhibited traits interpreted as being related to oil rendering from marine mammal blubber. The article discusses methods used in this oil production activity based on historical sources, archaeological investigations and experimental reconstruction of Iron Age slab-lined pits from Northern Norway.

  20. A Qualitative Approach of Identifying Major Cost Influencing Factors in Palm Oil Mills and the Relations towards Production Cost of Crude Palm Oil

    Directory of Open Access Journals (Sweden)

    Elaine L.Y. Man

    2011-01-01

    Full Text Available Problem statement: The oil palm industry, which heavily depends on the world market, is an export oriented industry. Worlds palm oil consumption was growing over the years. In addition, Indonesia and Malaysia dominated the oil palm industry. The oil palm industry in Malaysia is very competitive and become one of the major economic sectors contributing to the total revenue of the country. In year 2009, there was a total of 22.40 million tons of oil palm products including palm oil, palm kernel oil, palm kernel cake, oleo-chemicals and finished products, equivalent to RM 49.59 billion of export revenue. However, cost of production for Crude Palm Oil (CPO varies in a big gap. Therefore, it is essential to identify the major cost influencing factors in the production of CPO. Approach: The study system started with collection of Fresh Fruits Bunches (FFB from oil palm plantation to the production of CPO at palm oil mills. Two palm oil mills of different production capacity were chosen for this study. Statistical analysis was done to identify the major cost influencing factors of production cost for CPO. Results: The production cost of CPO for small scale palm oil mills preferably lied between RM 45 to RM 50 per metric tons while large scale palm oil mills lied below RM 45 per metric tons. Conclusion: Palm oil mills with higher production capacity were efficient in producing CPO than lower production capacity palm oil mills. Thus, the production cost of CPO was lower compared to that of small scale palm oil mills.

  1. Bio-oil production from palm fronds by fast pyrolysis process in fluidized bed reactor

    Science.gov (United States)

    Rinaldi, Nino; Simanungkalit, Sabar P.; Kiky Corneliasari, S.

    2017-01-01

    Fast pyrolysis process of palm fronds has been conducted in the fluidized bed reactor to yield bio-oil product (pyrolysis oil). The process employed sea sand as the heat transfer medium. The objective of this study is to design of the fluidized bed rector, to conduct fast pyrolysis process to product bio-oil from palm fronds, and to characterize the feed and bio-oil product. The fast pyrolysis process was conducted continuously with the feeding rate around 500 g/hr. It was found that the biomass conversion is about 35.5% to yield bio-oil, however this conversion is still minor. It is suggested due to the heating system inside the reactor was not enough to decompose the palm fronds as a feedstock. Moreover, the acids compounds ware mostly observed on the bio-oil product.

  2. Castor Oil: Properties, Uses, and Optimization of Processing Parameters in Commercial Production.

    Science.gov (United States)

    Patel, Vinay R; Dumancas, Gerard G; Kasi Viswanath, Lakshmi C; Maples, Randall; Subong, Bryan John J

    2016-01-01

    Castor oil, produced from castor beans, has long been considered to be of important commercial value primarily for the manufacturing of soaps, lubricants, and coatings, among others. Global castor oil production is concentrated primarily in a small geographic region of Gujarat in Western India. This region is favorable due to its labor-intensive cultivation method and subtropical climate conditions. Entrepreneurs and castor processors in the United States and South America also cultivate castor beans but are faced with the challenge of achieving high castor oil production efficiency, as well as obtaining the desired oil quality. In this manuscript, we provide a detailed analysis of novel processing methods involved in castor oil production. We discuss novel processing methods by explaining specific processing parameters involved in castor oil production.

  3. Castor Oil: Properties, Uses, and Optimization of Processing Parameters in Commercial Production

    Science.gov (United States)

    Patel, Vinay R.; Dumancas, Gerard G.; Kasi Viswanath, Lakshmi C.; Maples, Randall; Subong, Bryan John J.

    2016-01-01

    Castor oil, produced from castor beans, has long been considered to be of important commercial value primarily for the manufacturing of soaps, lubricants, and coatings, among others. Global castor oil production is concentrated primarily in a small geographic region of Gujarat in Western India. This region is favorable due to its labor-intensive cultivation method and subtropical climate conditions. Entrepreneurs and castor processors in the United States and South America also cultivate castor beans but are faced with the challenge of achieving high castor oil production efficiency, as well as obtaining the desired oil quality. In this manuscript, we provide a detailed analysis of novel processing methods involved in castor oil production. We discuss novel processing methods by explaining specific processing parameters involved in castor oil production. PMID:27656091

  4. Bio-oil production from fast pyrolysis of waste furniture sawdust in a fluidized bed.

    Science.gov (United States)

    Heo, Hyeon Su; Park, Hyun Ju; Park, Young-Kwon; Ryu, Changkook; Suh, Dong Jin; Suh, Young-Woong; Yim, Jin-Heong; Kim, Seung-Soo

    2010-01-01

    The amount of waste furniture generated in Korea was over 2.4 million tons in the past 3 years, which can be used for renewable energy or fuel feedstock production. Fast pyrolysis is available for thermo-chemical conversion of the waste wood mostly into bio-oil. In this work, fast pyrolysis of waste furniture sawdust was investigated under various reaction conditions (pyrolysis temperature, particle size, feed rate and flow rate of fluidizing medium) in a fluidized-bed reactor. The optimal pyrolysis temperature for increased yields of bio-oil was 450 degrees C. Excessively smaller or larger feed size negatively affected the production of bio-oil. Higher flow and feeding rates were more effective for the production of bio-oil, but did not greatly affect the bio-oil yields within the tested ranges. The use of product gas as the fluidizing medium had a potential for increased bio-oil yields.

  5. China's Offshore Oil and Gas Development and Production Towards Another Higher Level

    Institute of Scientific and Technical Information of China (English)

    Zhou Shengwei; Yan Hao

    1996-01-01

    @@ The oil and gas development and production of China National Offshore Oil Corporation (CNOOC) have already entered a continued, speedy, and efficient developing stage. During the period of the Eighth Five-Year Plan, 12offshore oil and gas fields came on-stream, the annual crude oil production increasing range all reached more than1- 2 million tons, the total output of crude oil being 26.17million tons, and natural gas, 1.4 billion cubic meters. In1995, crude oil production reached 8.41 million tons,natural gas reached 0.37 billion cubic meters, and the construction of Ya 13-1 gas field was completed with annual productivity of 3.45 billion cubic meters. the total value of assets has increased from 1.7 billion yuan in 1983to 32.8 billion yuan in 1995.

  6. Modelling future oil production, population and the economy

    Energy Technology Data Exchange (ETDEWEB)

    Laherrere, Jean

    2003-07-01

    Most published data on energy, population and the economy are unreliable. In many cases, authors have political motives, selectively choosing data from a wide range of uncertainty to give a desired image. In addition to the uncertainty of the measurements themselves, as in the case of population or the confidentiality of the oil reserves, they often indulge in manipulation. A so-called hedonistic factor distorts the calculation of GDP in the United States; and the definition of the Proved Reserves by the Securities and Exchange Commission gives rise to 'reserve growth'. OPEC misreports its oil reserves because its quotas depend upon the reported reserves, and the reserves were overestimated in the Soviet Union because economic and technical constraints were ignored. Our present culture of eternal growth makes the word 'decline' politically incorrect, but constant growth is unsustainable in a finite world. Growth is the Santa Claus of the modern age who is supposed to provide welfare and retirement for our children and us. All natural events, when measured over their full life, can be modelled under one or more cycles, as in the Fourier analysis. This cyclical nature corresponds with the finite nature of the Universe; everything that is born will die, whether we speak of the solar system, the Earth, or human species. What goes up must come down. The Russian population is already declining and Europe's will soon do so too. This basic understanding was recognised by the celebrated King Hubbert when he made his famous prediction in 1956 that US oil production would peak in 1970. But, in fact, he oversimplified by showing a single peak. In reality, US oil production had a secondary peak (93% of the first one) in 1985, reflecting the entry of Alaskan production, which itself peaked in 1988. A symmetrical oil cycle reflects a large number of independent producers, acting randomly, but in many cases economic and political factors disturb the

  7. Modelling future oil production, population and the economy

    Energy Technology Data Exchange (ETDEWEB)

    Laherrere, Jean

    2003-07-01

    Most published data on energy, population and the economy are unreliable. In many cases, authors have political motives, selectively choosing data from a wide range of uncertainty to give a desired image. In addition to the uncertainty of the measurements themselves, as in the case of population or the confidentiality of the oil reserves, they often indulge in manipulation. A so-called hedonistic factor distorts the calculation of GDP in the United States; and the definition of the Proved Reserves by the Securities and Exchange Commission gives rise to 'reserve growth'. OPEC misreports its oil reserves because its quotas depend upon the reported reserves, and the reserves were overestimated in the Soviet Union because economic and technical constraints were ignored. Our present culture of eternal growth makes the word 'decline' politically incorrect, but constant growth is unsustainable in a finite world. Growth is the Santa Claus of the modern age who is supposed to provide welfare and retirement for our children and us. All natural events, when measured over their full life, can be modelled under one or more cycles, as in the Fourier analysis. This cyclical nature corresponds with the finite nature of the Universe; everything that is born will die, whether we speak of the solar system, the Earth, or human species. What goes up must come down. The Russian population is already declining and Europe's will soon do so too. This basic understanding was recognised by the celebrated King Hubbert when he made his famous prediction in 1956 that US oil production would peak in 1970. But, in fact, he oversimplified by showing a single peak. In reality, US oil production had a secondary peak (93% of the first one) in 1985, reflecting the entry of Alaskan production, which itself peaked in 1988. A symmetrical oil cycle reflects a large number of independent producers, acting randomly, but in many cases economic and political factors disturb the

  8. Profit and Risk Measures in Oil Production Optimization

    DEFF Research Database (Denmark)

    Capolei, Andrea; Foss, Bjarne; Jørgensen, John Bagterp

    2015-01-01

    on the value of the uncertain parameters. In this case, a problem reformulation is needed to properly define the optimization problem. In this paper we describe the concept of risk and we explore how to handle the risk by using appropriate risk measures. We provide a review on various risk measures reporting...... pro and cons for each of them. Finally, among the presented risk measures, we identify two of them as appropriate risk measures when minimizing the risk.......In oil production optimization, we usually aim to maximize a deterministic scalar performance index such as the profit over the expected reservoir lifespan. However, when uncertainty in the parameters is considered, the profit results in a random variable that can assume a range of values depending...

  9. Food and biomass production in small oil expression facilities

    Energy Technology Data Exchange (ETDEWEB)

    Kato, H.; Kanai, G.; Yakushido, K. [National Agricultural Research Center, Tsukuba (Japan). Biomass Production and Processing Research Team

    2010-07-01

    This paper reported on a study in which rapeseeds were separated into high quality seed for food oil and low quality seed for biofuels. A laboratory-scale oilseed screw press was then used to examine the effects of choke opening and seed preheating on the rapeseed pressing performance and the quality of food oil and biofuels oil. Oil recovery and chlorophyll content was found to increase as maximum pressure increased. In terms of pressing performance, the rapeseed heated by microwaves yielded more oil and chlorophyll than without heating. The NEB ratio of microwave heating press with an 8.0 mm choke opening was advantageous. Rapeseed oil extracted from low quality seeds was found to have a high acid value. The quality of oil extracted by oilseed screw press was found to be good and met the requirements of the Codex Alimentarius for edible oils.

  10. Crude oil and alternate energy production forecasts for the twenty-first century: The end of the hydrocarbon era

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, J.D. [Univ. of Colorado, Boulder, CO (United States)

    1997-08-01

    Predictions of production rates and ultimate recovery of crude oil are needed for intelligent planning and timely action to ensure the continuous flow of energy required by the world`s increasing population and expanding economies. Crude oil will be able to supply increasing demand until peak world production is reached. The energy gap caused by declining conventional oil production must then be filled by expanding production of coal, heavy oil and oil shales, nuclear and hydroelectric power, and renewable energy sources (solar, wind, and geothermal). Declining oil production forecasts are based on current estimated ultimate recoverable conventional crude oil resources of 329 billion barrels for the United States and close to 3 trillion barrels for the world. Peak world crude oil production is forecast to occur in 2020 at 90 million barrels per day. Conventional crude oil production in the United States is forecast to terminate by about 2090, and world production will be close to exhaustion by 2100.

  11. Selection and production of oregano rich in essential oil and carvacrol

    OpenAIRE

    2005-01-01

    There is an increasing interest in oregano essential oil and its component carvacrol for the use as a feed additive with antimicrobial properties, enhancing the health of poultry and pigs. This chapter describes the initial agronomic attempts (in the years 2001-2004) to acquire and develop Origanum strains rich in essential oil and carvacrol for optimal field production (of crop biomass and essential oil yield) under Dutch climatic conditions. Research activities to improve field production o...

  12. Sand Production during Improved Oil Recovery in Unconsolidated Cores

    OpenAIRE

    Mohammad A. J. Ali.; S. M. Kholosy; A. A. Al-Haddad; K. K. AL-Hamad

    2012-01-01

    Steam injection is a mechanisms used for improved oil recovery (IOR) in heavy oil reservoirs. Heating the reservoir reduces the oil viscosity and causes the velocity of the moving oil to increase; and thus, the heated zone around the injection well will have high velocity. The increase of velocity in an unconsolidated formation is usually accompanied with sand movement in the reservoir creating a potential problem. Core samples from different wells in Kuwait were used to examine sand producti...

  13. Sub-inhibitory stress with essential oil affects enterotoxins production and essential oil susceptibility in Staphylococcus aureus.

    Science.gov (United States)

    Turchi, Barbara; Mancini, Simone; Pistelli, Luisa; Najar, Basma; Cerri, Domenico; Fratini, Filippo

    2017-06-08

    Fourteen wild strains of Staphylococcus aureus positive for gene sea were tested for enterotoxins production and the minimum inhibitory concentration of Leptospermum scoparium, Origanum majorana, Origanum vulgare, Satureja montana and Thymus vulgaris essential oils (EOs) were determined. After this trial, bacteria stressed with sub-inhibitory concentration of each EO were tested for enterotoxins production by an immunoenzymatic assay and resistance to the same EO. Oregano oil exhibited the highest antibacterial activity followed by manuka and thyme oils. After the exposure to a sub-inhibitory concentration of EOs, strains displayed an increased sensitivity in more than 95% of the cases. After treatment with oregano and marjoram EOs, few strains showed a modified enterotoxins production, while 43% of the strains were no longer able to produce enterotoxins after treatment with manuka EO. The results obtained in this study highlight that exposure to sub-inhibitory concentration of EO modifies strains enterotoxins production and EOs susceptibility profile.

  14. Increasing Heavy Oil Reserves in the Wilmington Oil Field Through Advanced Reservoir Characterization and Thermal Production Technologies, Class III

    Energy Technology Data Exchange (ETDEWEB)

    City of Long Beach; Tidelands Oil Production Company; University of Southern California; David K. Davies and Associates

    2002-09-30

    The objective of this project was to increase the recoverable heavy oil reserves within sections of the Wilmington Oil Field, near Long Beach, California through the testing and application of advanced reservoir characterization and thermal production technologies. The successful application of these technologies would result in expanding their implementation throughout the Wilmington Field and, through technology transfer, to other slope and basin clastic (SBC) reservoirs.

  15. Short-chain chlorinated paraffins in cooking oil and related products from China.

    Science.gov (United States)

    Cao, Yang; Harada, Kouji H; Liu, Wanyang; Yan, Junxia; Zhao, Can; Niisoe, Tamon; Adachi, Ayumu; Fujii, Yukiko; Nouda, Chihiro; Takasuga, Takumi; Koizumi, Akio

    2015-11-01

    Short-chain chlorinated paraffins (SCCPs) are emerging persistent organic pollutants. It has been found that dietary intakes of SCCPs in China have recently increased and are now higher than in Japan and Korea. The contribution of cooking oil to dietary exposure to SCCPs in China was evaluated by analyzing SCCPs in cooking oil, raw seeds used to produce cooking oil, and fried confectionery products collected in China in 2010 and 2012. Detectable amounts of SCCP homologs were found in 48 out of the 49 cooking oil samples analyzed, and the SCCP concentrations varied widely, from cooking oil ranged from Cooking oil might therefore be one of the sources of SCCPs to Chinese diets. SCCPs were also detected in raw seeds used to produce cooking oil, but the concentrations varied widely. The SCCP homolog patterns in the raw seed and cooking oil samples were different, implying that the seeds used to produce the oil (and therefore the soil on which the seeds were produced) were unlikely to be the sources of SCCPs in cooking oil. Further investigations are needed to determine the routes through which cooking oil becomes contaminated with SCCPs during the production and processing of the oil. Copyright © 2015 Elsevier Ltd. All rights reserved.

  16. Optimization of factors affecting the production of biodiesel from crude palm kernel oil and ethanol

    Directory of Open Access Journals (Sweden)

    David K. Kuwornoo, Julius C. Ahiekpor

    2010-07-01

    Full Text Available Biodiesel, an alternative diesel fuel made from renewable sources such as vegetable oils and animal fats, has been identified by government to play a key role in the socio-economic development of Ghana. The utilization of biodiesel is expected to be about 10% of the total liquid fuel mix of the country by the year 2020. Despite this great potential and the numerous sources from which biodiesel could be developed in Ghana, studies on the sources of biodiesel and their properties as a substitute for fossil diesel have tended to be limited to Jatropha oil. This paper, however, reports the parameters that influences the production of biodiesel from palm kernel oil, one of the vegetable oils obtained from oil palm which is the highest vegetable oil source in Ghana. The parameters studied are; mass ratio of ethanol to oil, reaction temperature, catalyst concentration, and reaction time using completely randomized 24 factorial design. Results indicated that ethanol to oil mass ratio, catalyst concentration and reaction time were the most important factors affecting the ethyl ester yield. There was also an interaction effect between catalyst and time and ethanol- oil ratio and time on the yield. Accordingly, the optimal conditions for the production of ethyl esters from crude palm kernel oil were determined as; 1:5 mass ratio of ethanol to oil, 1% catalyst concentration by weight of oil, 90 minutes reaction time at a temperature of 30 oC.

  17. A Qualitative Approach of Identifying Major Cost Influencing Factors in Palm Oil Mills and the Relations towards Production Cost of Crude Palm Oil

    OpenAIRE

    2011-01-01

    Problem statement: The oil palm industry, which heavily depends on the world market, is an export oriented industry. Worlds palm oil consumption was growing over the years. In addition, Indonesia and Malaysia dominated the oil palm industry. The oil palm industry in Malaysia is very competitive and become one of the major economic sectors contributing to the total revenue of the country. In year 2009, there was a total of 22.40 million tons of oil palm products including p...

  18. Contaminants, water quality, and wildlife mortality on oil production sites in western South Dakota. Interim report

    Energy Technology Data Exchange (ETDEWEB)

    Henry, C.J.; Ruelle, R.

    1993-04-01

    The objectives of the study were to evaluate oil pits and other hazards at oil production sites to (1) document the magnitude of wildlife mortality due to exposure to oil and other chemicals, (2) determine the physical and toxic effects of oil pit contents on wildlife, and (3) identify methods to prevent sublethal and lethal impacts to wildlife. Pits at oil production sites in Fall River and Harding Counties of western South Dakota were surveyed for wildlife carcasses by searching the shorelines and raking underwater around the pit edges in April, July, and October 1992. In July, composite water and sediment samples were collected from 26 pits, and analyzed for oil and grease. Bioassays were conducted with two life stages of Hyalella azteca and Daphnia magna to determine pit water toxicity. Seed germination tests were conducted using radish seeds exposed to pit water. Oil and poor water quality appeared to be the primary causes of pit liquid toxicity.

  19. The social and environmental context of argan oil production.

    Science.gov (United States)

    de Waroux, Yann le Polain

    2013-01-01

    In recent decades, argan oil has become one of the most expensive cosmetic oils on world markets. This review outlines the social and environmental context of the argan boom, highlighting its consequences on local livelihoods and conservation. It examines the claims that the argan oil boom has benefited the local population and that it encourages the conservation of argan woodlands.

  20. Antioxidant properties of rice bran oil-based extraction products

    Science.gov (United States)

    Rice bran oil has many properties that make it an attractive functional food ingredient. Compared with other oils, rice bran oil is relatively rich in tocopherols, tocotrienols, and y-oryzanol, all of which have been shown to have numerous desirable health effects. The same compounds thought to co...

  1. Biodiesel production from rice bran oil and supercritical methanol.

    Science.gov (United States)

    Kasim, Novy Srihartati; Tsai, Tsung-Han; Gunawan, Setiyo; Ju, Yi-Hsu

    2009-04-01

    In this study, production of biodiesel from low cost raw materials, such as rice bran and dewaxed-degummed rice bran oil (DDRBO), under supercritical condition was carried out. Carbon dioxide (CO2) was employed as co-solvent to decrease the supercritical temperature and pressure of methanol. The effects of different raw materials on the yield of biodiesel production were investigated. In situ transesterification of rice bran with supercritical methanol at 30MPa and 300 degrees C for 5 min was not a promising way to produce biodiesel because the purity and yield of fatty acid methyl esters (FAMEs) obtained were 52.52% and 51.28%, respectively. When DDRBO was reacted, the purity and yield were 89.25% and 94.84%, respectively. Trans-FAMEs, which constituted about 16% of biodiesel, were found. They were identified as methyl elaidate [trans-9], methyl linoleaidate [trans-9, trans-12], methyl linoleaidate [cis-9, trans-12], and methyl linoleaidate [trans-9, cis-12]. Hydrocarbons, which constituted about 3% of the reaction product, were also detected.

  2. A multi-criteria analysis approach for ranking and selection of microorganisms for the production of oils for biodiesel production.

    Science.gov (United States)

    Ahmad, Farah B; Zhang, Zhanying; Doherty, William O S; O'Hara, Ian M

    2015-08-01

    Oleaginous microorganisms have potential to be used to produce oils as alternative feedstock for biodiesel production. Microalgae (Chlorella protothecoides and Chlorella zofingiensis), yeasts (Cryptococcus albidus and Rhodotorula mucilaginosa), and fungi (Aspergillus oryzae and Mucor plumbeus) were investigated for their ability to produce oil from glucose, xylose and glycerol. Multi-criteria analysis (MCA) using analytic hierarchy process (AHP) and preference ranking organization method for the enrichment of evaluations (PROMETHEE) with graphical analysis for interactive aid (GAIA), was used to rank and select the preferred microorganisms for oil production for biodiesel application. This was based on a number of criteria viz., oil concentration, content, production rate and yield, substrate consumption rate, fatty acids composition, biomass harvesting and nutrient costs. PROMETHEE selected A. oryzae, M. plumbeus and R. mucilaginosa as the most prospective species for oil production. However, further analysis by GAIA Webs identified A. oryzae and M. plumbeus as the best performing microorganisms.

  3. LABORATORY EVALUATION OF OIL SPILL BIOREMEDIATION PRODUCTS IN SALT AND FRESHWATER SYSTEMS

    Science.gov (United States)

    Ten oil spill bioremediation products were tested in the laboratory for their ability to enhance biodegradation of weathered Alaskan North Slope crude oil in both fresh and salt-water media. The products included: nutrients to stimulate inoculated microorganisms, nutrients plus a...

  4. Regional Companies of PetroChina Expand Local Oil Products Market Rapidly

    Institute of Scientific and Technical Information of China (English)

    Zhang Kaiyu

    2001-01-01

    @@ Jilin Company Jilin Oil Products Sales Company of PetroChina marketed 1.58 millions of oil products and generated 160 million yuan of profits and taxes in 2000, setting a record high in the company's history.The market occupancy in Jilin Province has risen to 90 percent from the previous 50 percent in the past few years.

  5. Multi-layered satisficing decision making in oil and gas production platforms

    DEFF Research Database (Denmark)

    Lindegaard Mikkelsen, Lars; Jørgensen, B. N.

    2013-01-01

    From a control perspective, offshore oil and gas production is very challenging due to the many and potentially conflicting production objectives that arise from the intrinsic complexity of the oil and gas domain. In this paper, we show how a multi-layered multi-agent system can be used...

  6. Demonstrating multi-layered MAS in control of offshore oil and gas production

    DEFF Research Database (Denmark)

    Lindegaard Mikkelsen, Lars; Næumann, J. R.; Demazeau, Y.

    2013-01-01

    From a control perspective, offshore oil and gas production is very challenging due to the many and potentially conflicting production objectives that arise from the intrinsic complexity of the oil and gas domain. In this paper, we demonstrate how a multi-layered multi-agent system can be used...

  7. The Russian oil industry re-structuration: towards the emergence of western type enterprises?

    Energy Technology Data Exchange (ETDEWEB)

    Locatelli, C

    1999-01-01

    The Russian oil industry has undergone fundamental changes since the collapse of the Soviet Empire and its bureaucratic administrative structure, dominated by its various Branch Ministries. The monopoly in the Soviet oil industry has now been replaced by a number of ''oil companies'', some of which are very powerful, the best known of them being Lukoil. These ''joint stock companies'' are the product of a reform aimed essentially at implanting, out of all the numerous organisational arrangements developed in the West, the model of the vertically integrated private firm. Beyond the legal reforms in the Russian oil industry sector, however, the nature of the organisational model that has actually emerged in Russia begs several questions. Many entities, which are complex and highly diversified, are involved in this industry. There are, of course, the many private structures in which the banks sometimes carry a considerable amount of weight. There are also some vertically integrated organisations, but the degree of integration is variable and their method of centralization is based on a specific form of economic logic. It should not be considered, however, that these actors are similar to capitalist-type private enterprises, whose behaviour is regulated by the demands of international competition. Reform of property rights has not been sufficient to create true private enterprise in Russia. (author)

  8. Inorganic wastes in manufacturing of glass-ceramics. Slurry of phosphorous fertilizer production and oil shale ash

    Energy Technology Data Exchange (ETDEWEB)

    Gorokhovsky, A.V.; Mendez-Nonell, J.; Escalante-Garcia, J.I.; Pech-Canul, M.I.; Vargas-Gutierrez, G. [Department of Engineering Ceramics of CINVESTAV-IPN, Unidad Saltillo-Monterrey, km 13.5, Apartado Postal 663, CP 25000, Saltillo, Coahuila (Mexico); Gorokhovsky, V.A.; Mescheryakov, D.V. [Department of Building Materials of Saratov State Technical University, Saratov (Russian Federation)

    2001-11-01

    The use of bicomponent raw material mixtures of industrial wastes to produce pyroxene glass ceramics was investigated. It is shown that oil shale ash from heat power stations can promote the production of crystalline phases and the slurry from phosphorous fertilizer production can provide sufficient concentration of nucleating agents. Mechanical and chemical properties, as well as the structure and crystallization mechanism were characterized. An increase of phosphorous oxide and fluorine concentrations leads to a change of the crystallization mechanism.

  9. Analysis of oil-pipeline distribution of multiple products subject to delivery time-windows

    Science.gov (United States)

    Jittamai, Phongchai

    This dissertation defines the operational problems of, and develops solution methodologies for, a distribution of multiple products into oil pipeline subject to delivery time-windows constraints. A multiple-product oil pipeline is a pipeline system composing of pipes, pumps, valves and storage facilities used to transport different types of liquids. Typically, products delivered by pipelines are petroleum of different grades moving either from production facilities to refineries or from refineries to distributors. Time-windows, which are generally used in logistics and scheduling areas, are incorporated in this study. The distribution of multiple products into oil pipeline subject to delivery time-windows is modeled as multicommodity network flow structure and mathematically formulated. The main focus of this dissertation is the investigation of operating issues and problem complexity of single-source pipeline problems and also providing solution methodology to compute input schedule that yields minimum total time violation from due delivery time-windows. The problem is proved to be NP-complete. The heuristic approach, a reversed-flow algorithm, is developed based on pipeline flow reversibility to compute input schedule for the pipeline problem. This algorithm is implemented in no longer than O(T·E) time. This dissertation also extends the study to examine some operating attributes and problem complexity of multiple-source pipelines. The multiple-source pipeline problem is also NP-complete. A heuristic algorithm modified from the one used in single-source pipeline problems is introduced. This algorithm can also be implemented in no longer than O(T·E) time. Computational results are presented for both methodologies on randomly generated problem sets. The computational experience indicates that reversed-flow algorithms provide good solutions in comparison with the optimal solutions. Only 25% of the problems tested were more than 30% greater than optimal values and

  10. Remote and Onsite Direct Measurements of Emissions from Oil and Natural Gas Production

    Science.gov (United States)

    Environmentally responsible oil and gas production requires accurate knowledge of emissions from long-term production operations1, which can include methane, volatile organic compounds, and hazardous air pollutants. Well pad emissions vary based on the geologically-determined com...

  11. Environmental benefits of advanced oil and gas exploration and production technology

    Energy Technology Data Exchange (ETDEWEB)

    None

    1999-10-01

    THROUGHOUT THE OIL AND GAS LIFE CYCLE, THE INDUSTRY HAS APPLIED AN ARRAY OF ADVANCED TECHNOLOGIES TO IMPROVE EFFICIENCY, PRODUCTIVITY, AND ENVIRONMENTAL PERFORMANCE. THIS REPORT FOCUSES SPECIFICALLY ON ADVANCES IN EXPLORATION AND PRODUCTION (E&P) OPERATIONS.

  12. Gas Production Generated from Crude Oil Biodegradation: Preliminary Study on its Aplication in Microbial Enhanced Oil Recovery (MEOR

    Directory of Open Access Journals (Sweden)

    Astri Nugroho

    2009-11-01

    Full Text Available Gas Production Generated from Crude Oil Biodegradation: Preliminary Study on its Aplication in MicrobialEnhanced Oil Recovery (MEOR. The objective of this study is to observe the capacity of gas production generatedfrom crude oil degradation by the isolated bacteria. The gas in the MEOR could increase pressure in the reservoir,decrease oil viscosity, increase oil permeability-due to the increase of the porosity and viscosity, and also increase oilvolume due to the amount of dissolved gas. A research on gas analysis of oil degradation by 6 isolated bacteria has beenconducted. The bacteria isolates including Bacillus badius (A, Bacillus circulans (B, Bacillus coagulans (C, Bacillusfirmus (D, Pasteurella avium (E and Streptobacillus moniliformis (F. The trial on gas production, gas analysis and oildegradation analysis, was carried out by using SMSS medium. The test of gas production was done by usingmicrorespirometer at 40°C. The result shows that B, C, D, E produce more gas than A and F. Gas of CO2, O2, CO, N2,CH4, and H2 were analyzed by using GC. The results show that only three gases were detected by GC i.e. CO2, N2, andO2. The concentration of CO2 and N2 gas increased while the concentration of O2 decreased over an 8th day ofobservation. CO2 gas producted by mix culture was higher than by the pure culture. On the 8th day of incubation, theproduction of CO2 gas by mix culture was 4,0452% while pure culture C and D only produced 2,4543% and 2,8729%.The mix culture increase simple hydrocarbon by 12.03% and the formation of a complex hydrocarbon by 3.07%. Themix culture (C-D generated the highest concentration of CO2 gas as well as a synergistic concortium that has ability todegrade crude oil.

  13. Inflation and government indecisiveness: key deterrents to significant shale oil production by 1985

    Energy Technology Data Exchange (ETDEWEB)

    1976-10-01

    This work examines the progress of the shale oil industry in its efforts to achieve production of synthetic crude oil from oil shale on a profitable, commercial basis. A projection is made regarding the ability of the shale oil industry to produce 1,000,000 bbl of synthetic crude oil by 1985. That year was chosen because of the long lead time required to obtained leases; to acquire investment capital; to gain approval of environmental impact documents; and to acquire the equipment and construct plants of sufficient magnitude to be economically feasible. 31 references.

  14. Misassigned natural products and their revised structures.

    Science.gov (United States)

    Yoo, Hye-Dong; Nam, Sang-Jip; Chin, Young-Won; Kim, Min-Sun

    2016-02-01

    Natural products are a major pipeline for drug development and are responsible for more than 50 % of drugs on the market. NMR is a fundamental and powerful tool for the structure determination of natural products. It is essential to provide unambiguous chemical structure information on natural products in drug development research, including the structure-activity relationship, derivatization and pharmacokinetic/pharmacodynamic studies. Advancement of NMR instruments has made it possible to deal with nanomole-scale natural products for structure elucidation, but misinterpretation of NMR spectra still occurs. We review 21 natural products with revised chemical structures and the methods used for those revisions.

  15. Cottonseed oil for biodiesel production; Oleo de algodao para a producao de biodiesel

    Energy Technology Data Exchange (ETDEWEB)

    Pighinelli, Anna L.M.T.; Park, Kil J. [Universidade Estadual de Campinas (UNICAMP), SP (Brazil)], E-mail: annalets@feagri.unicamp.br; Ferrari, Roseli A.; Miguel, Ana M.R.O. [Instituto de Tecnologia de Alimentos (ITAL), Campinas, SP (Brazil)], Emails: roseliferrari@ital.sp.gov.br, anarauen@ital.sp.gov.br, kil@feagri.unicamp.br

    2009-07-01

    Crude cottonseed oil is an alternative for biodiesel production, mostly in Mato Grosso State, where its production is the biggest of Brazil. Even being an acid oil, esterification reaction, followed by transesterification, could make possible the biodiesel production. In this study, crude cottonseed oil obtained from expelled process was reacted to evaluate molar ration and catalyst concentration effects in biodiesel yield. Molar ratio varied from 3 to 15 moles of ethanol to 1 mol of oil, and catalyst, from 1 to 5% by oil mass. Statistic analysis showed that none of studied variables was significant, for the values range. Biodiesel yield had a maximum of 88%, for molar ratio of 4.7 and 4.42% of catalyst concentration. A combination of oil with high free fatty acid content and ethanol as alcohol, affected the separation between esters and glycerol. (author)

  16. Comparative evaluation of structured oil systems: Shellac oleogel, HPMC oleogel, and HIPE gel

    Science.gov (United States)

    Patel, Ashok R; Dewettinck, Koen

    2015-01-01

    In lipid-based food products, fat crystals are used as building blocks for creating a crystalline network that can trap liquid oil into a 3D gel-like structure which in turn is responsible for the desirable mouth feel and texture properties of the food products. However, the recent ban on the use of trans-fat in the US, coupled with the increasing concerns about the negative health effects of saturated fat consumption, has resulted in an increased interest in the area of identifying alternative ways of structuring edible oils using non-fat-based building blocks. In this paper, we give a brief account of three alternative approaches where oil structuring was carried out using wax crystals (shellac), polymer strands (hydrophilic cellulose derivative), and emulsion droplets as structurants. These building blocks resulted in three different types of oleogels that showed distinct rheological properties and temperature functionalities. The three approaches are compared in terms of the preparation process (ease of processing), properties of the formed systems (microstructure, rheological gel strength, temperature response, effect of water incorporation, and thixotropic recovery), functionality, and associated limitations of the structured systems. The comparative evaluation is made such that the new researchers starting their work in the area of oil structuring can use this discussion as a general guideline. Practical applications Various aspects of oil binding for three different building blocks were studied in this work. The practical significance of this study includes (i) information on the preparation process and the concentrations of structuring agents required for efficient gelation and (ii) information on the behavior of oleogels to temperature, applied shear, and presence of water. This information can be very useful for selecting the type of structuring agents keeping the final applications in mind. For detailed information on the actual edible applications

  17. On the identification of Product Structure Laws

    DEFF Research Database (Denmark)

    Andreasen, Mogens myrup; Hansen, Claus thorp; Mortensen, Niels henrik

    1997-01-01

    Based on the WDK-school's design theory we try to make a balance on product structuring with respect to functional and behavioural product synthesis, the structuring of a product into units, modules, and reusable products, and the definition of a product family, which might be configured...... into products without any additional design effort. Asustainable theoretical foundation with articulated laws is presented. The theoretical foundation has only had a limited impact on the recent years research contributions, but its importance is growing. The article contribute to a detailed language within...... the area of product structuring, which clarifies the imprecise use of terminology in industrial practise....

  18. Production of surfactin by bacillus subtilis mtcc 2423 from waste frying oils

    Directory of Open Access Journals (Sweden)

    N. Vedaraman

    2011-06-01

    Full Text Available One of the obstacles in the way of wide scale industrial application of biosurfactants is the high production cost coupled with a low production rate. In order to lower the production cost surfactin production by Bacillus subtilis MTCC 2423 was studied in submerged batch cultivation using waste frying oils. It was observed that the decrease in surface tension was 56.32%, 48.5% and 46.1% with glucose, waste frying sunflower oil and waste frying rice bran oil, respectively. Biomass formation was 4.36 g/L, 3.67 g/L and 4.67 g/L for glucose, waste frying sunflower oil and waste frying rice bran oil, respectively. Product yield (g product/g substrate was 2.1%, 1.49% and 1.1% with glucose, waste frying sunflower oil and waste frying rice bran oil as substrates. This process facilitates safe disposal of waste frying oil, as well reducing the production cost of surfactin.

  19. Effects of Cymbopogon citratus L. essential oil on the growth, morphogenesis and aflatoxin production of Aspergillus flavus ML2-strain.

    Science.gov (United States)

    Helal, G A; Sarhan, M M; Abu Shahla, A N K; Abou El-Khair, E K

    2007-02-01

    The mycelial growth of Aspergillus flavus Link was completely inhibited using 1.5 (microl/ml or 2.0 (microl/ml of Cymbopogon citratus essential oil applied by fumigation or contact method in Czapek's liquid medium, respectively. This oil was found also to be fungicidal at the same concentrations. The sublethal doses 1.0 and 1.5 (microl/ml inhibited about 65% of fungal growth after five days of incubation and delayed conidiation as compared with the control. Microscopic observations using Light Microscope (LM), Scanning Electron Microscope (SEM) and Transmission Electron Microscope (TEM) were carried out to determine the ultra structural modifications of A. flavus hyphae after treatment with C. citratus essential oil. The hyphal diameter decreased and hyphal wall appeared as precipitates and disappeared in some regions. This oil also caused plasma membrane disruption and mitochondrial structure disorganization. Moreover, Ca(+2), K(+) and Mg(+2) leakages increased from the fumigated mycelium and its total lipid content decreased, while the saturated and unsaturated fatty acids increased. One of the most important results obtained during this study was the ability of C. citratus essential oil at its sublethal dose to completely inhibit aflatoxin B(1) production from A. flavus. These findings increase the possibility of exploiting C. citratus essential oil as an effective inhibitor of biodegradation and storage contaminating fungi and also in fruit juice preservation.

  20. Using of mucilage palm oil in the toilet soap production.

    Directory of Open Access Journals (Sweden)

    Girgis, Adel Y.

    1999-06-01

    Full Text Available Mucilage palm oil (M.P.O. was obtained from physical refining step for crude palm oil. The components of M.P.O. were high content of free fatty acids (82.2% with simple amount of neutral oil (11.9%, while the residual content (unsaponifiable matter and impurities was 2.1% and in addition to 3.8% water. The results indicated that the colours of M.P.O., tallow and palm kemel oil improved after bleaching. Eight soap samples (n.os 1-8 were prepared from bleached fatty blends of mucilage palm oil, tallow and palm kernel oil at different ratios. The results showed that the moisture contents of soap samples n.os 2,7 and 8 were high compared with the standard soap (sample n.os 1, subsequently their total fatty matters became lower than that found in the control soap (sample n.os 1. The findings marked that the unsaponifiable matter of soaps nos 2,7 and 8 were higher compared with the other soaps. No high differences were observed in the free alkali of all soaps (range from 0.06 to 0.09%. On the other hand, high differences were found in the free oil of all soap samples (n.os2-8 compared with the standard soap (sample nos 1, except soap samples n.os2,7 and 8, which record very high. The best soap samples in the colour were in the following increasing order: n.os1 > 3 > 4 > 5 > 6 > 7 > 8 > 2, respectively. The results showed that the better soap samples in the physical properties were in the following increasing order: soap nos 3> soap nos 4> soap n.os 5> soap n.os 6 compared with the standard soap (sample nos 1, where from firm structure with high foam, while the other soap samples (n.os 2,7 and 8 were poor quality (i.e., low lathering properties with deep colours. Therefore, it could be concluded that mucilage palm oil can be used as a new fatty material for toilet soap manufacturing at

  1. Therapeutic switching: from antidermatophytic essential oils to new leishmanicidal products

    Directory of Open Access Journals (Sweden)

    Emeline Houël

    2015-02-01

    Full Text Available This study examined whether the antidermatophytic activity of essential oils (EOs can be used as an indicator for the discovery of active natural products against Leishmania amazonensis. The aerial parts of seven plants were hydrodistilled. Using broth microdilution techniques, the obtained EOs were tested against three strains of dermatophytes (Trichophyton mentagrophytes, Microsporum gypseum and Microsporum canis. To compare the EOs antifungal and antiparasitic effects, the EOs activities against axenic amastigotes of L. amazonensis were concurrently evaluated. For the most promising EOs, their antileishmanial activities against parasites infecting peritoneal macrophages of BALB/c mice were measured. The most interesting antifungal candidates were the EOs from Cymbopogon citratus, Otacanthus azureus and Protium heptaphyllum, whereas O. azureus, Piper hispidum and P. heptaphyllum EOs exhibited the lowest 50% inhibitory concentration (IC50 values against axenic amastigotes, thus revealing a certain correspondence between both activities. The P. hispidum EO was identified as the most promising product in the results from the infected macrophages model (IC50: 4.7 µg/mL, safety index: 8. The most abundant compounds found in this EO were sesquiterpenes, notably curzerene and furanodiene. Eventually, the evaluation of the antidermatophytic activity of EOs appears to be an efficient method for identifying new potential drugs for the treatment of L. amazonensis.

  2. Structure-activity relations of water-in-oil vaccine formulations and induced antigen-specific antibody responses.

    Science.gov (United States)

    Jansen, Theo; Hofmans, Marij P M; Theelen, Marc J G; Schijns, Virgil E J C

    2005-01-11

    Water-in-oil (W/O) emulsions are known as most effective adjuvants to generate high and durable antibody responses to vaccine antigens following a single immunization. However, their structural requirements remain poorly understood. Here we addressed the significance of certain pharmaceutical characteristics including water/oil ratios--ranging from 60/40 to 30/70 (w/w(%))--droplet size and type of oil, i.e. non-metabolizable (mineral oil) versus metabolizable (Miglyol 840). Stability of emulsions was accomplished by the use of a polymeric emulsifier. Distinct W/O emulsions were formulated with inactivated (i) infectious bronchitis virus (iIBV) and Newcastle disease virus (iNDV), and evaluated in immunized chickens for magnitude and duration of in vivo antiviral antibody formation and local reactions. A high mineral oil content proved most effective for antibody response formation. In general, a larger droplet size evoked higher antibody responses for both oil types. Inoculum residues proved lower using biodegradable Miglyol, when compared to mineral oil, for all emulsion variants. Especially water-to-oil ratio and droplet size may provide useful parameters for improving (antiviral) antibody production by W/O emulsions.

  3. INCREASING HEAVY OIL RESERVES IN THE WILMINGTON OIL FIELD THROUGH ADVANCED RESERVOIR CHARACTERIZATION AND THERMAL PRODUCTION TECHNOLOGIES

    Energy Technology Data Exchange (ETDEWEB)

    Scott Hara

    2001-06-27

    The objective of this project is to increase the recoverable heavy oil reserves within sections of the Wilmington Oil Field, near Long Beach, California through the testing and application of advanced reservoir characterization and thermal production technologies. The successful application of these technologies will result in expanding their implementation throughout the Wilmington Field and, through technology transfer, to other slope and basin clastic (SBC) reservoirs. The existing steamflood in the Tar zone of Fault Block II-A (Tar II-A) has been relatively inefficient because of several producibility problems which are common in SBC reservoirs: inadequate characterization of the heterogeneous turbidite sands, high permeability thief zones, low gravity oil and non-uniform distribution of the remaining oil. This has resulted in poor sweep efficiency, high steam-oil ratios, and early steam breakthrough. Operational problems related to steam breakthrough, high reservoir pressure, and unconsolidated sands have caused premature well and downhole equipment failures. In aggregate, these reservoir and operational constraints have resulted in increased operating costs and decreased recoverable reserves. A suite of advanced reservoir characterization and thermal production technologies are being applied during the project to improve oil recovery and reduce operating costs.

  4. First ever ice oil product carrier built by China for foreign shipowner

    Institute of Scientific and Technical Information of China (English)

    Chen Jianan; Chen Hao

    2004-01-01

    @@ As energy supply becomes more and more intense in the world, Russia, whose Baltic regions are abundant of oil, is increasing its oil production and importation. With the prosperity of shipping industry, shipping companies along the Baltic coast increases every year its demand for oil tankers suitable for navigation in their ice sea. In 2004,Guangzhou Shipyard International was awarded a contract for construction of two52000 ton dwt ice oil product carriers. Now detailed design is under way. According to the contract, the two carriers shall be delivered respectively in December 2006 and in May 2007.

  5. An evaluation of oil spill responses for offshore oil production projects in Newfoundland and Labrador, Canada: Implications for seabird conservation.

    Science.gov (United States)

    Fraser, Gail S; Racine, Vincent

    2016-06-15

    Seabirds are vulnerable to oil pollution, particularly in cold-water regions. We investigated the response of small spills (oil production operations Environment Canada requested monitoring and mitigation of small spills potentially impacting seabird populations; suggestions supported by two independent reviews. An industry spill response plan states that operators would collect systematic observations on spills and deploy countermeasures where possible. Operators' spill reports were obtained under an Access to Information request. There were 220 daytime spills with sheens (out of 381 spills; 1997-2010). Of these, six reported time to oil dispersion and eleven the presence or absence of seabirds. Industry self-reporting has not permitted an evaluation of the impact of chronic oil spills on seabirds. We recommend that independent observers be placed on platforms to systematically collect data on spills and seabirds.

  6. Low cost and conformal microwave water-cut sensor for optimizing oil production process

    KAUST Repository

    Karimi, Muhammad Akram

    2015-08-01

    Efficient oil production and refining processes require the precise measurement of water content in oil (i.e., water-cut) which is extracted out of a production well as a byproduct. Traditional water-cut (WC) laboratory measurements are precise, but are incapable of providing real-time information, while recently reported in-line WC sensors (both in research and industry) are usually incapable of sensing the full WC range (0 – 100 %), are bulky, expensive and non-scalable for the variety of pipe sizes used in the oil industry. This work presents a novel implementation of a planar microwave T-resonator for fully non-intrusive in situ WC sensing over the full range of operation, i.e., 0 – 100 %. As opposed to non-planar resonators, the choice of a planar resonator has enabled its direct implementation on the pipe surface using low cost fabrication methods. WC sensors make use of series resonance introduced by a λ/4 open shunt stub placed in the middle of a microstrip line. The detection mechanism is based on the measurement of the T-resonator’s resonance frequency, which varies with the relative percentage of oil and water (due to the difference in their dielectric properties). In order to implement the planar T-resonator based sensor on the curved surface of the pipe, a novel approach of utilizing two ground planes is proposed in this work. The innovative use of dual ground planes makes this sensor scalable to a wide range of pipe sizes present in the oil industry. The design and optimization of this sensor was performed in an electromagnetic Finite Element Method (FEM) solver, i.e., High Frequency Structural Simulator (HFSS) and the dielectric properties of oil, water and their emulsions of different WCs used in the simulation model were measured using a SPEAG-dielectric assessment kit (DAK-12). The simulation results were validated through characterization of fabricated prototypes. Initial rapid prototyping was completed using copper tape, after which a

  7. Enhancing Jatropha oil extraction yield from the kernels assisted by a xylan-degrading bacterium to preserve protein structure

    Energy Technology Data Exchange (ETDEWEB)

    Marasabessy, Ahmad [Wageningen Univ. (Netherlands). Valorisation of Plant Production Chains; RijksUniv. Groningen (Netherlands). Dept. of Chemical Engineering; Agency for the Assessment and Application of Technology (BPPT), Jakarta (Indonesia); Wageningen Univ. (Netherlands). Agrotechnology and Food Sciences Group; Moeis, Maelita R. [Institut Teknologi Bandung, Bandung (Indonesia). School of Life Sciences and Technology; Sanders, Johan P.M.; Weusthuis, Ruud A. [Wageningen Univ. (Netherlands). Valorisation of Plant Production Chains

    2011-06-15

    We investigated the use of bacterial cells isolated from paddy crab for the extraction of oil from Jatropha seed kernels in aqueous media while simultaneously preserving the protein structures of this protein-rich endosperm. A bacterial strain - which was marked as MB4 and identified by means of 16S rDNA sequencing and physiological characterization as either Bacillus pumilus or Bacillus altitudinis - enhanced the extraction yield of Jatropha oil. The incubation of an MB4 starter culture with preheated kernel slurry in aqueous media with the initial pH of 5.5 at 37 C for 6 h liberated 73% w/w of the Jatropha oil. Since MB4 produces xylanases, it is suggested that strain MB4 facilitates oil liberation via degradation of hemicelluloses which form the oil-containing cell wall structure of the kernel. After MB4 assisted oil extraction, SDS-PAGE analysis showed that the majority of Jatropha proteins were preserved in the solid phase of the extraction residues. The advantages offered by this process are: protein in the residue can be further processed for other applications, no purified enzyme preparation is needed, and the resulting oil can be used for biodiesel production. (orig.)

  8. Characterization of Bio-Oil: A By-Product from Slow Pyrolysis of Oil Palm Empty Fruit Bunches

    OpenAIRE

    Khor, K.H; Lim, K. O.; Z. A. Zainal

    2009-01-01

    Problem statement: Oil palm Empty Fruit Bunches (EFB) are abundant biomass in Malaysia. Studies about production of biofuels using slow pyrolysis of EFB are still lacking. So, this study was aimed to understand the physical and chemical properties of the bio-oil and its simple blends. Approach: EFB was slow pyrolysed with internal heating at terminal temperature of 600°C in a pilot kiln and the main product is the EFB char and the condensates from the emissions were separated into aqueous and...

  9. EFFECT OF ESSENTIAL OIL ON BIOFILM PRODUCTION BY DIFFERENT LISTERIA MONOCYTOGENES STRAINS

    Directory of Open Access Journals (Sweden)

    G. Comi

    2008-12-01

    Full Text Available The effects of different essential oil (hexanal, 2-(E-hexenal, carvacrol, citron, red orange, thymol and limonene on biofilm production of some Lmonocytogenes strains are evaluated. The formation of biofilm on certain surfaces or on the food, seems to be related with cross-contamination during processing or with the contamination of the final product, with potential risk for the consumer. Many studies were done on the antimicrobial activity of essential oils and their components, but not too much is known about their capacity to influence and reduce the microbial production of biofilm. Our data showed that essential oils can inhibit or limit the biofilm production.

  10. Manufacturing of vegetable oils-based epoxy and composites for structural applications

    Science.gov (United States)

    Wang, Rongpeng

    Epoxidized vegetable oil (EVO) is one of the largest industrial applications of vegetable oils (VOs) and is widely used as a plasticizer and as a synthetic intermediate for polyol or unsaturated polyester. However, the utility of EVO as monomer for high performance epoxy thermoset polymer is limited by its reactivity and by the resulting physical properties. Herein, VO-based epoxy monomers, i.e., glycidyl esters of epoxidized fatty acids derived from soybean oil (EGS) or linseed oil (EGL), have been synthesized and were benchmarked against commercial available diglycidyl ether of bisphenol A (DGEBA) and also epoxidized soybean oil (ESO) controls. EGS and EGL possessed higher oxirane content, more reactivity and lower viscosity than ESO or epoxidized linseed oil (ELO), provided better compatibility with DGEBA as a reactive diluent, and yielded thermally and mechanically stronger polymers than polymers obtained using ESO. Glass transition temperatures (T g) of the VO-based epoxy thermoset polymers were mostly a function of monomer oxirane content with some added structural influences of epoxy reactivity, and presence of a pendant chain. Organo-modified montmorillonite clay (OMMT) and long glass fiber reinforced composites (FRC) were efficiently manufactured using anhydride cured EGS as matrices. The OMMT nanocomposites showed higher mechanical and thermal strength than the neat polymers but were also dependent on the dispersion techniques and the clay concentration. Surprisingly, the neat EGS-anhydride matrix FRC showed comparable properties, such as flexural and impact strengths and slightly lower Tg, versus DGEBA based counterparts. These high performance monomers, polymers, and composites have potential to replace petroleum-based epoxy as value-added products from VOs compared to EVOs.

  11. A Canadian perspective on the supply costs, production and economic impacts from oil sands development

    Energy Technology Data Exchange (ETDEWEB)

    McColl, D.; Masri, M. [Canadian Energy Research Inst., Calgary, AB (Canada)

    2008-05-15

    This article provided a synopsis of oil sands research recently conducted at the Canadian Energy Research Institute (CERI). The production profiles and capital expenditures that CERI has projected for oil sands projects were explored along with the macroeconomic benefits associated with oil sands development. In addition to rising capital and operating costs, bitumen producers are challenged by labour shortages and environmental concerns. However, CERI warrants continued growth in production from the oil sands industry, given the current high price state of the global oil market and security of supply concerns from oil importing countries. This article also provided background information and analysis to assess the implications of future development. The projected growth in the oil sands industry creates demands for infrastructure, housing, health care, education, and business services. The economic impacts were measured at the local, provincial, national and global levels in terms of changes in gross domestic product; changes in employment; and, changes in government revenues. It was concluded that with continued investment and development, Alberta's oil sands resource is expected to continue to produce oil for decades, and would eventually achieve 6 MMbpd production. 8 refs., 3 tabs., 10 figs.

  12. HYDROPROCESSING OF MICROALGAE OIL FOR GREEN DIESEL PRODUCTION

    Directory of Open Access Journals (Sweden)

    2016-12-01

    Full Text Available This research was carried out to simulate microalgae oil hydroprocessing plant using ASPEN HYSYS simulation package. The simulation is based on conditions and parameters (temperature, pressure and catalyst selectivity obtained from consulted literatures. After the successful completion of the simulation, total recovery of products for green diesel and propane was achieved as 85.6% and 4.01% (mass percentages respectively. The green diesel composition indicated 0.01, 0.0005, 0.0201, 0.0757, 0.0021, 0.0089, 0.0041, 0.1813, 0.6822, 0.0191, and 0.005 mass fractions of n-C15, n-C16, n-C17, n-C18, n-C21, i-C15, i-C16, i-C17, i-C18, i-C21 and H2O respectively. The quality specifications of the simulated Green diesel with Cetane number 86.7 fall within acceptable range and met the United State diesel standard ASTM D975. A complete disappearance of triglycerides in the product mixture at the hydrotreating temperature of 371 and deg;C and pressure of 20 bar was observed. Economic analysis of the simulated project gives a total capital cost of ₦5.184billion, total production cost of ₦5.01 billion and cash flow as revenue of ₦6.02 billion after the fourth year. It shows that the project is highly profitable and efficient with a pay-back period of approximately 4years.

  13. A selection and seed-grower are a substantial factor of increase to the productivity of oil-bearing cultures

    Directory of Open Access Journals (Sweden)

    В. В. Кириченко

    2013-02-01

    Full Text Available Analysis of oilseeds in Ukraine, including sunflower, soybean, winter and spring rape, mustard, linseed, sesame, spring false flax, safflower. Presented research-based elements of the technology of cultivation. Described seed of oilseeds. Named most promising varieties of these crops. Disclosed their productive and qualitative potential. The above varietal structure of oilseeds in the State Register of plant varieties suitable for dissemination in Ukraine for years. In order to ensure stable population of oil and food, which include oil, and for the implementation of programs related to soil fertility, scientifically grounded recommended area of oilseeds in Ukraine for 2013–2015 years, ha.

  14. Pyrolysis of Parinari polyandra Benth fruit shell for bio-oil production

    Directory of Open Access Journals (Sweden)

    Temitope E. Odetoye

    2014-09-01

    Full Text Available Non-conventional agricultural residues such as Parinari polyandra Benth fruit shell (PPBFS are potential sources of biomass feedstock that have not been investigated for bio oil production. In this study, PPBFS was pyrolyzed via an intermediate pyrolysis process for the production of bio oil. The bio oils were obtained using a fixed bed reactor within a temperature range of 375–550 oC and were characterized to determine their physicochemical properties. The most abundant organic compounds present were acetic acid, toluene, 2-cyclopenten-1-one, 2-furanmethanol, phenol, guaiacol and 2,6-dimethoxyphenol. The bio-oil produced at 550 oC possessed a higher quantity of desirable compounds than those produced at lower temperatures. The presence of acetic acids in the bio-oil suggested the need to upgrade the bio-oil before utilization as a fuel source.

  15. Remote sensing for oil products on water surface via fluorescence induced by UV filaments

    Science.gov (United States)

    Sunchugasheva, E. S.; Ionin, A. A.; Mokrousova, D. V.; Seleznev, L. V.; Sinitsyn, D. V.; Geints, Yu. E.; Zemlyanov, A. A.

    2016-10-01

    Remote monitoring of water pollution, namely thin films of oil or oil products on water surface, can be carried out by laser fluorimetry. The pollutants fluorescence during its interaction with ultrashort UV laser pulses was experimentally studied in this paper. The laser pulses power was considered in a wide range of values including the filamentation regime. We compared fluorescence stimulated by femtosecond UV laser pulses with two central wavelengths (248 and 372 nm) for detection of crude oil and the following oil products: oil VM-5, oil 5W-40 and solvent WhiteSpirit. It was shown that shorter UV wavelengths are more suitable for fluorescence excitation. The spatial resolution of the fluorescence localization was no worse than 30 cm. We discuss techniques of high intensity emission delivery to the remote target as post-filamentation channels and multifilamentation beam propagation regime as well experimentally and numerically.

  16. Distillation Parameters for Pilot Plant Production of Laurus nobilis Essential oil

    Directory of Open Access Journals (Sweden)

    Temel Özek

    2012-01-01

    Full Text Available Essential oils have increasing importance in flavour and fragrance industries. They are obtained by distillation techniques. In order to produce an oil with market potential its optimum production parameters have to be well known prior to its commercial production. Determination of the steam distillation parameters of commercially available Laurel leaves oil in pilot plant scale is described. The effect of steam rate and processing time play a major role in distillation of essential oils. Distillation speed was high in the beginning of the process, then gradually reduced as the distillation proceeded. The main component of the oil of Laurel leaf oil was 1,8-cineole accumulating significantly in the early fractions.

  17. Estimating primary productivity of tropical oil palm in Malaysia using remote sensing technique and ancillary data

    Science.gov (United States)

    Kanniah, K. D.; Tan, K. P.; Cracknell, A. P.

    2014-10-01

    The amount of carbon sequestration by vegetation can be estimated using vegetation productivity. At present, there is a knowledge gap in oil palm net primary productivity (NPP) at a regional scale. Therefore, in this study NPP of oil palm trees in Peninsular Malaysia was estimated using remote sensing based light use efficiency (LUE) model with inputs from local meteorological data, upscaled leaf area index/fractional photosynthetically active radiation (LAI/fPAR) derived using UK-DMC 2 satellite data and a constant maximum LUE value from the literature. NPP values estimated from the model was then compared and validated with NPP estimated using allometric equations developed by Corley and Tinker (2003), Henson (2003) and Syahrinudin (2005) with diameter at breast height, age and the height of the oil palm trees collected from three estates in Peninsular Malaysia. Results of this study show that oil palm NPP derived using a light use efficiency model increases with respect to the age of oil palm trees, and it stabilises after ten years old. The mean value of oil palm NPP at 118 plots as derived using the LUE model is 968.72 g C m-2 year-1 and this is 188% - 273% higher than the NPP derived from the allometric equations. The estimated oil palm NPP of young oil palm trees is lower compared to mature oil palm trees (trees contribute to lower oil palm LAI and therefore fPAR, which is an important variable in the LUE model. In contrast, it is noted that oil palm NPP decreases with respect to the age of oil palm trees as estimated using the allomeric equations. It was found in this study that LUE models could not capture NPP variation of oil palm trees if LAI/fPAR is used. On the other hand, tree height and DBH are found to be important variables that can capture changes in oil palm NPP as a function of age.

  18. ZnO nanorods as catalyts for biodiesel production from olive oil

    Science.gov (United States)

    Molina, Carmen Maria Miralda

    The motivation to determine a viable alternative to petroleum based energy has risen in recent years due to increased greenhouse gas emissions, environmental pollution, and the fear of exhausting oil and natural gas reserves. Biodiesel derived from the transesterification of vegetable oils or animal fats has emerged as a viable alternative to petroleum diesel. However, for this to become an option available to the average consumer it is vital to find an effective catalyst. Metal oxides have emerged as potential heterogeneous catalysts. ZnO in particular is attractive because it is abundant. The use of nanostructures has been shown to improve the catalytic performance of ZnO. ZnO nanorods were synthesized using a solution approach. The crystalline structure, morphology, and surface area were confirmed using XRD, SEM, and BET surface area respectively. The characterized nanorods were used as catalysts for the production of biodiesel. The nanorods achieved conversions of 94.8% at 150°C for reaction times of eight hours. They also demonstrated better catalytic performance, attributed to their increased degree of crystallinity, than conventional ZnO. A kinetic study at 150°C to determine the reaction rate parameters was also conducted. Due to the presence of three distinct phases in the reaction, initially the reaction rate is dominated by mass transfer limitations. However, these are eventually overcome and the reaction proceeds with a pseudo-first order with respect to the oil and a reaction rate constant of 0.5136 h-1.

  19. Production of cellulose phosphate from oil palm empty fruit bunch: Effect of chemical ratio

    Science.gov (United States)

    Rohaizu, R.; Wanrosli, W. D.

    2015-06-01

    Cellulose phosphate was synthesized from oil palm biomass residue that has the potential to represent a considerable added value product for the oil palm biomass utilization. Cellulose phosphate (CP) is prepared viaa phosphorylation process using the H3PO4/P2O5/Et3PO4/hexanol sequence using oil palm empty fruit bunch microcrystalline cellulose (OPEFB-MCC) as the starting material. Various factors affect its synthesis; one of them which is the subject of this investigation is the orthophosphoric acid (H3PO4) to triethylphosphate(Et3PO4) ratio which have the capability to increase the phosphorus content of CP. It is believed that during this reaction, the esterification of the free hydroxyl groups of the cellulose occurred. The H3PO4/Et3PO4 ratios applied were 0.16, 1.00, and 1.84. The effect of the H3PO4/Et3PO4 ratio on phosphorus content, yield, water swelling and molecular structure of CP are discussed.

  20. Production Cost Assessment of Palm Empty Fruit Bunch Conversion to Bio-Oil via Fast Pyrolysis

    Directory of Open Access Journals (Sweden)

    Yoga Peryoga

    2014-01-01

    Full Text Available Production cost assessment was based on palm oil mill of 30 metrics tons FFB/h capacity that produced EFB residue at app. 20 % wt of the initial FFB fed to the plant. The bio-oil plant will be located in the palm oil mill complex to eliminate the transportation cost of the EFB feedstock. The process included in this calculation is chopping, drying, grinding, pyrolysis, solid removal, bio oil recovery, and storage. The production cost is influenced by the amount of bio-oil production, material cost, operational cost including labor and utility cost. The sensitivity analysis shows that feedstock price drives the production cost. The result concludes that for the current condition, the bio-oil production cost from palm empty fruit bunch seems promising to be implemented in Indonesia. The best option is to have the bio-oil plant integrated with the palm oil mill, where in this case the EFB can be kept at no cost, off the market influence.

  1. Soils and waste water purification from oil products using combined methods under the North conditions.

    Science.gov (United States)

    Evdokimova, Galina A; Gershenkop, Alexander Sh; Mozgova, Natalia P; Myazin, Vladimir A; Fokina, Nadejda V

    2012-01-01

    Oil and gas production and transportation in Russia is increasingly moving to the north regions. Such regions are characterized by relatively low self-purification capacity of the natural environments from the contaminants due to slow character of the energy exchange and mass transfer processes. Off-shore field development in the Barents Sea and oil product transportation can result in contamination, as confirmed by the national and international practice of the developed oil and gas regions. The research aims at development of the soil bioremediation methods and industrial waste water purification contaminated by oil products in the north-western region of Russia. The dynamics of oil products carry-over have been investigated under the field model experiments in podzolic soils: gas condensate, diesel fuel and mazut from oil and the plants were selected for phyto-remediation of contaminated soils under high north latitudes. It is shown that soil purification from light hydrocarbons takes place during one vegetation period. In three months of the vegetation period the gas condensate was completely removed from the soil, diesel fuel - almost completely (more than 90%). Residual amounts of heavy hydrocarbons were traced, even 1.5 later. The following plants that were highly resistant to the oil product contamination were recommended for bioremediation: Phalaroides arundinacea, Festuca pratensis, Phleum pratense, Leymus arenarius. There has been developed and patented the combined method of treatment of waste water contaminated with hydrocarbons based on inorganic coagulants and local oil-oxidizing bacteria.

  2. Modernization or Conservation: The Role of Export Duty on Crude Oil and Petroleum Products

    OpenAIRE

    Georgy Idrisov; Sergey Sinelnikov-Murylev

    2012-01-01

    This paper deals with the analysis of the consequences of the abolition of export duties on crude oil and petroleum products as a necessary measure to create incentives to improve energy efficiency of the Russian economy and the elimination of underdevelopment caused by the unprecedented long-term subsidies to inefficient Russian oil refining. The authors consider three possible scenarios for the abolition of export duties on crude oil and domestic market and the conservation of tax revenues ...

  3. Analysis of multicriteria models application for selection of an optimal artificial lift method in oil production

    OpenAIRE

    Crnogorac, Miroslav P.; Danilović, Dušan Š.; Karović-Maričić, Vesna D.; Leković, Branko A.

    2016-01-01

    In the world today for the exploitation of oil reservoirs by artificial lift methods are applied different types of deep pumps (piston, centrifugal, screw, hydraulic), water jet pumps and gas lift (continuous, intermittent and plunger). Maximum values of oil production achieved by these exploitation methods are significantly different. In order to select the optimal exploitation method of oil well, the multicriteria analysis models are used. In this paper is presented an analysis of the multi...

  4. Oil shale production and power generation in Estonia; Economic and environmental dilemmas

    Energy Technology Data Exchange (ETDEWEB)

    Barabaner, N.I.; Kaganovich, I.Z. (Estonian Academy of Sciences, Tallinn (Estonia). Inst. of Economics)

    1993-06-01

    Combustive oil shale is the main type of fuel used in Estonian power plants. The economic state of the oil shale mining industry has deteriorated during the last decade. The development of oil shale production and use in power generation is accompanied by severe environmental pollution. The future of shale based power generation in Estonia depends on building new small capacity mines, in conjunction with the renovation and reconstruction of existing power plants and implementing measures to protect the environment. (author)

  5. Statistical Optimization of Fermentation Conditions for Cellulase Production from Palm Oil Mill Effluent

    OpenAIRE

    Jamal I. Daoud; Md. Z. Alam

    2010-01-01

    Problem statement: Palm oil mill effluent discharged by the oil palm industries is considered as the mixed of high polluted effluent which is abundant (about 20 million tonnes year-1) and its effect contributes to the serious environmental problems through the pollution of water bodies. Approach: The aim of this study was to identify the potential of low cost substrate such as Palm Oil Mill Effluent (POME) for the production of cellulase enzyme by liquid state bioconversion. The filamentous f...

  6. Minimising hydrogen sulphide generation during steam assisted production of heavy oil

    OpenAIRE

    Wren Montgomery; Sephton, Mark A.; Watson, Jonathan S.; Huang Zeng; Andrew C. Rees

    2015-01-01

    The majority of global petroleum is in the form of highly viscous heavy oil. Traditionally heavy oil in sands at shallow depths is accessed by large scale mining activities. Recently steam has been used to allow heavy oil extraction with greatly reduced surface disturbance. However, in situ thermal recovery processes can generate hydrogen sulphide, high levels of which are toxic to humans and corrosive to equipment. Avoiding hydrogen sulphide production is the best possible mitigation strateg...

  7. Role of Methane Capture for Sustainable Biodiesel Production from Palm Oil: A Life Cycle Assessment Approach

    OpenAIRE

    Hermawan Prasetya; Yandra Arkeman; Erliza Hambali

    2013-01-01

    Palm Oil Mill Effluent (POME) is one of the major wastes generated by palm oil milling which is a part of palm oil diesel production chain. POME contain of methane (about 60-70 %), which contribute to Greenhouse Gas (GHG) Emission. Due to reduction GHG emission is one of indicator bioenergy sustainability, some alternatives have been implementing to reduction it. One of the alternatives is implementing of methane capture technology which able to capture and/or utilize it for energy source. In...

  8. Biodiesel production from waste cooking oil using ionic liquid choline hydroxide as a catalyst

    OpenAIRE

    Aline Mara Maia Bessa

    2015-01-01

    The production of biodiesel is generally performed by alkaline transesterification oils with low amounts of free fatty acids (FFAs). In order to decrease the costs of production of biodiesel, low quality waste cooking oils or grease have been investigated as a source alternative, but problems in the purification step due to the formation of soap are found in catalysis with sodium hydroxide. In this work, the ionic liquid choline hydroxide was produced and used as catalyst in the production o...

  9. Jump dynamics with structural breaks for crude oil prices

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Yen-Hsien [Department of Finance, Chung Yuan Christian University (China); Hu, Hsu-Ning [Department of Money, Banking and Finance, TamKang University (China); Chiou, Jer-Shiou [Department of Finance and Banking, Shih Chien University, 70 Ta-Chih Street, Taipei 104 (China)

    2010-03-15

    This study investigates the joint phenomena of permanent and transitory components in conditional variance and jump intensity along with verification of structural breaks for crude oil prices. We adopt a Component-ARJI model with structural break analysis, utilizing daily data on West Texas Intermediate crude oil spot and futures contracts. The analytical results verify the existence of permanent and transitory components in conditional variance, with the permanent component of conditional variance increasing with the occurrence of a sudden major event (such as the Iraqi Invasion of Kuwait, Operation Desert Storm and the war between the US and Iraq), and a relatively greater increase in the transitory component over the same period. Notably, jump intensity fluctuates with an increase in the transitory component of conditional variance in response to abnormal events. It is the transitory component which serves as the primary influential factor for jumps in returns; therefore, speculators are willing to take large risks, particularly with respect to anticipating future price movements, or gambling, in the hopes of rapidly making substantial gains; thus, speculators prefer the temporary volatility component and engage in trade activities. However, investors prefer the permanent volatility component, because they may well be better off relocating their assets into more stable portfolios to outperform the market portfolio over the long run. (author)

  10. HEAT EXCHANGE NETWORKS IN BIODIESEL PRODUCTION FROM WASTE COOKING OILS

    Directory of Open Access Journals (Sweden)

    María Fernanda Laborde

    2014-11-01

    Full Text Available With the objective to aboard one of the challenges in Engineering teaching: It´s the application in professional practice?, along with attending to the actual requirements of achieve energetic efficiency in industrial process and to reuse wastes of food industry, this work, presents the application of heat exchange networks for the resolution of a real case: pre-treatment of waste cooking oils (WCO withacid catalysis for biodiesel production. Different methods and software are applied to obtain the minimum amounts of heat and the heat exchange network for a processing capacity of 0,19 kg/s of WCO. A minimum temperature difference (Tmin of 10°C is considered and the minimum requirements of heating and cooling result 4629,87 W and 10066,30 W, respectively. If this exchange network is not considered, this values increase to 26838,33 W and 21958,33 W, respectively. Applying heat exchange network, decrease 78,92% the required steam service in the process and water cooling service decreases 62,48%, demonstrating that integration reduces energetic requirements respect the non-integrated process.

  11. Mathematical analysis of intermittent gas injection model in oil production

    Science.gov (United States)

    Tasmi, Silvya, D. R.; Pudjo, S.; Leksono, M.; Edy, S.

    2016-02-01

    Intermittent gas injection is a method to help oil production process. Gas is injected through choke in surface and then gas into tubing. Gas forms three areas in tubing: gas column area, film area and slug area. Gas column is used to propel slug area until surface. A mathematical model of intermittent gas injection is developed in gas column area, film area and slug area. Model is expanding based on mass and momentum conservation. Using assume film thickness constant in tubing, model has been developed by Tasmi et. al. [14]. Model consists of 10 ordinary differential equations. In this paper, assumption of pressure in gas column is uniform. Model consist of 9 ordinary differential equations. Connection of several variables can be obtained from this model. Therefore, dynamics of all variables that affect to intermittent gas lift process can be seen from four equations. To study the behavior of variables can be analyzed numerically and mathematically. In this paper, simple mathematically analysis approach is used to study behavior of the variables. Variables that affect to intermittent gas injection are pressure in upstream valve and in gas column. Pressure in upstream valve will decrease when gas mass in valve greater than gas mass in choke. Dynamic of the pressure in the gas column will decrease and increase depending on pressure in upstream valve.

  12. Reproducibility of LCA models of crude oil production.

    Science.gov (United States)

    Vafi, Kourosh; Brandt, Adam R

    2014-11-04

    Scientific models are ideally reproducible, with results that converge despite varying methods. In practice, divergence between models often remains due to varied assumptions, incompleteness, or simply because of avoidable flaws. We examine LCA greenhouse gas (GHG) emissions models to test the reproducibility of their estimates for well-to-refinery inlet gate (WTR) GHG emissions. We use the Oil Production Greenhouse gas Emissions Estimator (OPGEE), an open source engineering-based life cycle assessment (LCA) model, as the reference model for this analysis. We study seven previous studies based on six models. We examine the reproducibility of prior results by successive experiments that align model assumptions and boundaries. The root-mean-square error (RMSE) between results varies between ∼1 and 8 g CO2 eq/MJ LHV when model inputs are not aligned. After model alignment, RMSE generally decreases only slightly. The proprietary nature of some of the models hinders explanations for divergence between the results. Because verification of the results of LCA GHG emissions is often not possible by direct measurement, we recommend the development of open source models for use in energy policy. Such practice will lead to iterative scientific review, improvement of models, and more reliable understanding of emissions.

  13. Optimization of electrical supply systems of oil production installations

    Energy Technology Data Exchange (ETDEWEB)

    Nissenbaum, I.A.; Novoselov, Yu.B.; Tsekhnov, A.N.

    1979-01-01

    The problem of optimization of electrical system assumes determination of the method for constructing the system, the functioning of which would assure minimal values of the technical-economic criterion -- costs, which are the basic economic factor in construction and exploitation of the system. When designing electro-supply systems for oil production installations, in particular, the pump stations, three principal versions of the optimization problem are possible, which are determined by the different conditions of the system, the type of minimizing criteria and volume of optimizing parameters. The most difficult optimization of an electrical system is when it is characterized only by assumed values of active power flow, which are determined by the specific energy requirements of the planned technological processes and the type of equipment used. Second, the more common optimization problem is improvement of the existing electrical network, with established processes and equipment use. The third version is a developing system, in which as a result of introduction of new technological installations, or remodeling of old ones, and which may result in a sharp change or re-distribution of the active power supply. Determining operating regimen of the system and optimization of economic-technical criteria should be a result of large-scale calculation and simulation using a digital computer, and use of iteration and non-linear programming methods.

  14. Production of high quality water for oil sands application

    Energy Technology Data Exchange (ETDEWEB)

    Beaudette-Hodsman, C.; Macleod, B. [Pall Corp., Mississauga, ON (Canada); Venkatadri, R. [Pall Corp., East Hills, NY (United States)

    2008-10-15

    This paper described a pressurized microfiltration membrane system installed at an oil sands extraction site in Alberta. The system was designed to complement a reverse osmosis (RO) system installed at the site to produce the high quality feed water required by the system's boilers. Groundwater in the region exhibited moderate total suspended solids and high alkalinity and hardness levels, and the RO system required feed water with a silt density index of 3 or less. The conventional pretreatment system used at the site was slowing down production due to the severe fouling of the RO membranes. The new microfiltration system contained an automated PVDF hollow fiber microfiltration membrane system contained in a trailer. Suspended particles and bacteria were captured within the filter, and permeate was sent to the RO unit. Within 6 hours of being installed, the unit was producing water with SDI values in the range of 1.0 to 2.5. It was concluded that the microfiltration system performed reliably regardless of wide variations in feed water quality and flow rates. 3 refs., 1 tab., 8 figs.

  15. Factors impacting the formation of monochloropropanediol (MCPD) fatty acid diesters during palm (Elaeis guineensis) oil production.

    Science.gov (United States)

    Craft, Brian D; Nagy, Kornél; Sandoz, Laurence; Destaillats, Frédéric

    2012-01-01

    Recently, organic and inorganic chlorinated compounds were detected in crude and commercially refined palm oils. Further, the predominant formation mechanism of monochloropropanediol (MCPD) diesters at high temperatures (>170-180°C) was revealed. The present study involved the development and comparison of solutions to mitigate MCPD diester levels in oils from various stages of palm oil production. Partially refined palm oil samples and oil extracted from fresh palm fruits were submitted to bench-top deodorisation experiments. Application of glycerol and ethanol as refining aids during the deodorisation of refined-bleached palm oil proved to be moderately effective; about 25%-35% reduction of MCPD diester levels was achieved. Washing crude palm oil with ethanol-water (1:1) prior to deodorisation was also an effective strategy yielding an ∼30% reduction of MCPD diester contents. Washing palm fruit pulp before oil extraction, however, was most impactful, resulting in a 95% reduction of MCPD diesters when compared to the deodorised control oil. This suggests that intervention upstream in the process chain is most efficient in reducing levels of these contaminants in refined oils. Following the study, a root-cause analysis was performed in order to map the parameters potentially responsible for the occurrence of MCPD diesters in refined palm oil and related fractions.

  16. Production of Biodiesel from Parinari polyandra B. Seed Oil using ...

    African Journals Online (AJOL)

    Akorede

    The acid value of 2.620 mg KOH/g obtained for the crude oil is suitable for biodiesel .... Khalil, A.; Shaikh S.N., and Nudrat Z.R. (2014). Reinforcement of natural ... transesterification of soybean oil into biodiesel: Effects of biodiesel on engine ...

  17. Is ascaridole a sensitizing degradation product in tea tree oil?

    NARCIS (Netherlands)

    Christoffers, Wietske Andrea; Blömeke, Brunhilde; Coenraads, Pieter Jan; Schuttelaar, Marielouise

    2014-01-01

    Background: Tea tree oil is a natural oil, which contains a-terpinene. Degradation of a-terpinene results in the endoperoxide ascaridole, which may cause allergic contact dermatitis. Objectives: To study the prevalence of sensitizations to ascaridole, the optimal patch test concentration, concomitan

  18. CNPC Cooperates with Russian Company in Oil Products Business

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    @@ China National Petroleum Corporation (CNPC) plans to set up a joint venture with Russian oil giant Rosneft to open up to 300 service stations in China. The joint venture, in which the Chinese company has a controlling stake, will cover oil refinery and retail business.

  19. New guidelines for oil spill identification of waterborne petroleum and petroleum products

    Energy Technology Data Exchange (ETDEWEB)

    Faksness, L.G.; Daling, P.S. [SINTEF Energy Research, Trondheim (Norway); Hansen, A.B. [National Environmental Research Inst., Roskilde (Denmark); Kienhuis, P. [RIZA, (Netherlands); Duus, R. [Norwegian Standard Association (Norway)

    2005-07-01

    Advances in interpretive and analytical methods have opened the possibility to improve the existing Nordtest methodology for oil spill identification which was developed in 1991 under the Nordic Council of Ministers. In 2002, the European Committee for Standardization (CEN) established 2 working groups to revise the Nordtest Methodology into the following 2 CEN guidelines: (1) oil spill identification which includes waterborne and petroleum products, and (2) oil spill identification which in addition to including waterborne petroleum and petroleum products, includes analytical methodology and interpretation of results. The revised methodology includes a protocol/decision chart that has 3 tiered levels of analyses and data treatment. The methodology relies on the characterization of diagnostic ratios. The CEN working group intends to use the guidelines as a basis for a national oil spill identification protocol in each European country and for further international use. The methodology can be applied to oil samples of petrogenic origin with boiling points above 200 degrees C, such as crude oils, diesel fuel oils, residual bunker oils, lubricants, and mixtures of oily bilge and sludge samples. It is not intended for automotive gasolines or other light petroleum products. The method has been implemented in most forensic laboratories in Europe and has successfully differentiated between oils from a spill and possible pollution sources. 19 refs., 4 tabs., 10 figs.

  20. Use of re-esterified palm oils, differing in their acylglycerol structure, in weaning-piglet diets.

    Science.gov (United States)

    Vilarrasa, E; Barroeta, A C; Tres, A; Esteve-Garcia, E

    2015-08-01

    Re-esterified oils are new fat sources obtained from chemical esterification of acid oils with glycerol (both economically interesting by-products from oil refining and biodiesel industries, respectively). The different fatty acid (FA) positional distribution and acylglycerol composition of re-esterified oils may enhance the apparent absorption of saturated fatty acids (SFA) and, thus, their overall nutritive value. The aim of the present study was to investigate the potential use of re-esterified palm oils, in comparison with their corresponding acid and native oils, and also with an unsaturated fat source in weaning-piglet diets. The parameters assessed were: FA apparent absorption, acylglycerol and free fatty acid (FFA) composition of feces, and growth performance. One-hundred and twenty weaning piglets (average weight of 8.50±1.778 kg) were blocked by initial BW (six blocks) and randomly assigned to five dietary treatments, resulting in four piglets per pen and six replicates per treatment. Dietary treatments were a basal diet supplemented with 10% (as-fed basis) of native soybean oil (SN), native palm oil (PN), acid palm oil (PA), re-esterified palm oil low in mono- (MAG) and diacylglycerols (DAG) (PEL), or re-esterified palm oil high in MAG and DAG (PEH). Results from the digestibility balance showed that SN reached the greatest total FA apparent absorption, and statistically different from PN, PA and PEL (P0.05), but PEH achieved the greatest total FA apparent absorption. Animals fed PEL, despite the fact that PEL oil contained more sn-2 SFA, did not show an improved absorption of SFA (P>0.05). Animals fed PA and PN showed similar apparent absorption coefficients (P>0.05), despite the high FFA content of PA oil. The acylglycerol and FFA composition of feces was mainly composed of FFA. There were no significant differences in growth performance (P>0.05). Results of the present study suggest that, despite the different acylglycerol structure of re

  1. Composition and structure of agents responsible for development of water repellency in soils following oil contamination.

    Science.gov (United States)

    Litvina, Marina; Todoruk, Tiona R; Langford, Cooper H

    2003-07-01

    Soil from the Ellerslie site of experimental oil contamination in Alberta developed water repellency some years after initial remediation. The water-repellent soils were compared to clean soils and contaminated but wettable soils by solid-state nuclear magnetic resonance (NMR). The effects of extraction with CH2Cl2 (for petroleum hydrocarbons), NaOH (for natural organic matter), and 2-propanol/ammonia (IPA/NH3) on wettability were evaluated by the molarity of the ethanol droplet (MED) test. Soil extracts and whole soils, after extraction, were examined using NMR and Fourier transform infrared spectroscopy (FTIR). On the basis of the structure--MED correlations, a model of a thin-layer natural organic matter--petroleum products complex formed under strong drying conditions is proposed to account for the development of water repellency. Studies of two similar soils from accidental oil spills are supportive.

  2. Utilization of oil extracted from spent coffee grounds for sustainable production of polyhydroxyalkanoates.

    Science.gov (United States)

    Obruca, Stanislav; Petrik, Sinisa; Benesova, Pavla; Svoboda, Zdenek; Eremka, Libor; Marova, Ivana

    2014-07-01

    Spent coffee grounds (SCG), an important waste product of the coffee industry, contain approximately 15 wt% of coffee oil. The aim of this work was to investigate the utilization of oil extracted from SCG as a substrate for the production of poly(3-hydroxybutyrate) (PHB) by Cupriavidus necator H16. When compared to other waste/inexpensive oils, the utilization of coffee oil resulted in the highest biomass as well as PHB yields. Since the correlation of PHB yields and the acid value of oil indicated a positive effect of the presence of free fatty acids in oil on PHB production (correlation coefficient R (2) = 0.9058), superior properties of coffee oil can be probably attributed to the high content of free fatty acids which can be simply utilized by the bacteria culture. Employing the fed-batch mode of cultivation, the PHB yields, the PHB content in biomass, the volumetric productivity, and the Y P/S yield coefficient reached 49.4 g/l, 89.1 wt%, 1.33 g/(l h), and 0.82 g per g of oil, respectively. SCG are annually produced worldwide in extensive amounts and are disposed as solid waste. Hence, the utilization of coffee oil extracted from SCG is likely to improve significantly the economic aspects of PHB production. Moreover, since oil extraction decreased the calorific value of SCG by only about 9 % (from 19.61 to 17.86 MJ/kg), residual SCG after oil extraction can be used as fuel to at least partially cover heat and energy demands of fermentation, which should even improve the economic feasibility of the process.

  3. Subsurface fracture mapping using microearthquakes detected during primary oil production, Clinton County, Kentucky

    Energy Technology Data Exchange (ETDEWEB)

    Rutledge, J.T.; Phillips, W.S. [Nambe Geophysical, Inc. (United States); Roff, A.; Albright, J.N. [Los Alamos National Lab., NM (United States); Hamilton-Smith, T. [Kentucky Geological Survey (United States); Jones, S.K.; Kimmich, K.C. [Meridian Exploration Corp. (United States)

    1994-09-01

    Downhole microseismic monitoring tests were conducted in Clinton County, Kentucky to determine if microearthquakes associated with primary production could be detected on a scale of interwell distances ({>=}400 ft) and to determine if such microearthquakes could be used to map reservoir fractures. The oil reservoirs occur in shallow (750 to 2400 ft), low-porosity (< 2%), carbonate rocks of Ordovician age. The reservoir system controlling the occurrence and flow of off and its relationship to the local and regional geology is poorly understood. Discrete reservoir microearthquakes were detected at an average rate of 11 events per week and at distances up to 4000 ft in an initial monitoring test using a single, triaxial downhole geophone receiver. In a second monitoring test 2 downhole, triaxial geophone tools were placed in a monitor well 800 ft from a new, high-volume oil well. Over a 6-month period of continuous monitoring 165 discrete, high-quality, microearthquake waveforms were recorded. Approximately 11,000 barrels of fluid were extracted in the monitor area during the 6-month period. Presently, it is unknown whether or not the microseismicity is induced by production. Hypocenters computed for 121 events delineate 4 extensive (up to 0.15 square-miles), low-angle, planar features striking approximately N65{degrees}E within the Ordovician reservoir depth interval. A composite fault-plane solution indicates a thrust focal mechanism. Such thrust structures are not observed in the surface-exposed Mississippian section, which lies above and is separated from the Ordovician section by a major unconformity of Devonian age. General relationships between the fractures revealed by the microseismicity and oil occurrence have yet to be demonstrated in the study area. The observed microseismicity occurs away from production wells, and to date, no new wells have been drilled into the mapped fracture along which shear displacement was detected.

  4. Increasing Heavy Oil Reserves in the Wilmington Oil Field through Advanced Reservoir Characterization and Thermal Production Technologies

    Energy Technology Data Exchange (ETDEWEB)

    City of Long Beach; David K.Davies and Associates; Tidelands Oil Production Company; University of Southern California

    1999-06-25

    The objective of this project is to increase the recoverable heavy oil reserves within sections of the Wilmington Oil Field, near Long Beach, California. This is realized through the testing and application of advanced reservoir characterization and thermal production technologies. It is hoped that the successful application of these technologies will result in their implementation throughout the Wilmington Field and through technology transfer, will be extended to increase the recoverable oil reserves in other slope and basin clastic (SBC) reservoirs. The existing steamflood in the Tar zone of Fault Block (FB) II-A has been relatively insufficient because of several producability problems which are common in SBC reservoir; inadequate characterization of the heterogeneous turbidite sands, high permeability thief zones, low gravity oil and non-uniform distribution of the remaining oil. This has resulted in poor sweep efficiency, high steam-oil ratios, and early breakthrough. Operational problems related to steam breakthrough, high reservoir pressure, and unconsolidated sands have caused premature well and downhole equipment failures. In aggregate, these reservoir and operational constraints have resulted in increased operating costs and decreased recoverable reserves.

  5. Production of oxidatively stable fish oil enriched food emulsions

    DEFF Research Database (Denmark)

    Bruni Let, Mette

    Purpose: The objective of the project is to determine how a number of selected fish oil enriched foods can be protected against oxidation by the right choice of antioxidants, emulsifiers and optimal process conditions. Furthermore the influence of antioxidant addition to the fish oil it......-self on the effect of antioxidants added to the foods will also be investigated. Background: Fish oils are rich sources of the long-chain polyunsaturated fatty acids EPA and DHA of which DHA is a vital component of the phospholipids of human cellular membranes, especially those in the brain and retina. Fish oils...... have many other health benefiting properties such as preventing heart diseases. Addition of fish oils to foods is therefore of interest. The many double bonds in the fatty acids are however susceptible to oxidation. Collaboration partners: The project is a collaborative project between DFU-FF, Bio...

  6. Biodiesel production from jatropha oil in a closed system

    Directory of Open Access Journals (Sweden)

    Shaaban W.

    2016-01-01

    Full Text Available The use of biodiesel as an alternative fuel is becoming increasingly popular nowadays due to global energy shortage. The interest in using Jatropha as a non-edible oil feedstock is rapidly growing. Biodiesel produced from crude Jatropha oil with NaOH as a catalyst is investigated. Transesterification by methanol is carried out in a closed vessel as a batch system. Factors affecting the process which included the reaction temperature and pressure, reaction time, the molar ratio of methanol to oil and catalyst amount are investigated. The maximum conversion ratio of methyl ester yield of 97.7% was recorded under the conditions of 65 °C, 1% (by mass NaOH of the oil mass and 6:1 methanol to oil ratio.

  7. Preliminary Economics for the Production of Pyrolysis Oil from Lignin in a Cellulosic Ethanol Biorefinery

    Energy Technology Data Exchange (ETDEWEB)

    Jones, Susanne B.; Zhu, Yunhua

    2009-04-01

    Cellulosic ethanol biorefinery economics can be potentially improved by converting by-product lignin into high valued products. Cellulosic biomass is composed mainly of cellulose, hemicellulose and lignin. In a cellulosic ethanol biorefinery, cellulose and hemicellullose are converted to ethanol via fermentation. The raw lignin portion is the partially dewatered stream that is separated from the product ethanol and contains lignin, unconverted feed and other by-products. It can be burned as fuel for the plant or can be diverted into higher-value products. One such higher-valued product is pyrolysis oil, a fuel that can be further upgraded into motor gasoline fuels. While pyrolysis of pure lignin is not a good source of pyrolysis liquids, raw lignin containing unconverted feed and by-products may have potential as a feedstock. This report considers only the production of the pyrolysis oil and does not estimate the cost of upgrading that oil into synthetic crude oil or finished gasoline and diesel. A techno-economic analysis for the production of pyrolysis oil from raw lignin was conducted. comparing two cellulosic ethanol fermentation based biorefineries. The base case is the NREL 2002 cellulosic ethanol design report case where 2000 MTPD of corn stover is fermented to ethanol (NREL 2002). In the base case, lignin is separated from the ethanol product, dewatered, and burned to produce steam and power. The alternate case considered in this report dries the lignin, and then uses fast pyrolysis to generate a bio-oil product. Steam and power are generated in this alternate case by burning some of the corn stover feed, rather than fermenting it. This reduces the annual ethanol production rate from 69 to 54 million gallons/year. Assuming a pyrolysis oil value similar to Btu-adjusted residual oil, the estimated ethanol selling price ranges from $1.40 to $1.48 (2007 $) depending upon the yield of pyrolysis oil. This is considerably above the target minimum ethanol selling

  8. Structured Analysis and Supervision Applied on Heavy Fuel Oil Tanks

    Directory of Open Access Journals (Sweden)

    LAKHOUA Mohamed Najeh

    2016-05-01

    Full Text Available This paper introduces the need for structured analysis and real time (SA-RT method of controlcommand applications in a thermal power plant (TPP using a supervisory control and data acquisition system (SCADA. Then, the architecture of a SCADA system in a TPP is presented. A significant example of a control-command application is presented. It is about the heavy fuel oil tanks of a TPP. Then an application of a structured analysis method, generally used in industry, on the basis of the SA-RT formalism is presented. In fact, different modules are represented and described: Context Diagram, Data Flows Diagram, Control Flows Diagram, State Transition Diagram, Timing Specifications and Requirements Dictionary. Finally, this functional and operational analysis allows us to assist the different steps of the specification, the programming and the configuration of a new tabular in a SCADA system.

  9. Technical aspects of production and analysis of biodiesel from used cooking oil. A review

    Energy Technology Data Exchange (ETDEWEB)

    Enweremadu, C.C.; Mbarawa, M.M. [Department of Mechanical Engineering, Tshwane University of Technology, Private Bag X680, Pretoria 001 (South Africa)

    2009-12-15

    The increasing awareness of the depletion of fossil fuel resources and the environmental benefits of biodiesel fuel has made it more attractive in recent times. The cost of biodiesel, however, is the major hurdle to its commercialization in comparison to petroleum-based diesel fuel. The high cost is primarily due to the raw material, mostly neat vegetable oil. Used cooking oil is one of the economical sources for biodiesel production. However, the products formed during frying, can affect the transesterification reaction and the biodiesel properties. This paper attempts to review various technological methods of biodiesel production from used cooking oil. The analytical methods for high quality biodiesel fuel from used cooking oil like GC, TLC, HPLC, GPC and TGA have also been summarized in this paper. In addition, the specifications provided by different countries are presented. The fuel properties of biodiesel fuel from used cooking oil were also reviewed and compared with those of conventional diesel fuel. (author)

  10. Oxidative stability during storage of structured lipids produced from fish oil and caprylic acid

    DEFF Research Database (Denmark)

    Nielsen, Nina Skall; Xu, Xuebing; Timm Heinrich, Maike;

    2004-01-01

    Structured lipids produced by enzymatic or chemical methods for different applications have been receiving considerable attention. The oxidative stability of a randomized structured lipid (RFO), produced by chemical interesterification from fish oil (FO) and tricaprylin, and a specific structured...

  11. Development of Goat - Palm Oil Integrated Production System : An Assessment Based on Feed Availability and Nutrient Requirements

    Directory of Open Access Journals (Sweden)

    Simon P Ginting

    2006-06-01

    Full Text Available The integration of goats and palm oil plantation is prospective agricultural production systems that exploit the complement relationship among various components in the system . The main components are the oil palm trees, vegetation underneath the trees, processing plant of palm oil bunch, and the goat . The estimation of carrying capacity of the plantation system is based on the quantitative analysis on nutrient supply from various feed resources in the plantation system and nutrient requirements for goat production . The goat demographic parameters, such as, prolificacy, fertility and fecundity are used to estimate the goat population size, dynamics and structures . The development of production model could be based on a certain production target, such as the number of animals sold or the amount of income (demand driven approach, or based on the availability of certain resources such as feed supply (supply driven approach . Using the demand driven approach, and considering 6000 heads of oneyear old goats to fill the Malaysian market as the production target, it is calculated that a population size of 3,636 does and 810 ha of palm oil plantation are required to meet this production target . In a typically medium-size oil palm plantation system (500 ha of oil palm plantation with one unit of small-scale palm oil bunch processing plant ( l ton/hour, the potency to supply metabolisable energy from various feed resources in the system is 2,778,800 Mcal/year, equivalent to a carrying capacity of 5,155 Goat Units/year . This system could carry 2,951 does and 295 bucks to produce 1,116 heads of one-year old goats annually . A medium-size oil palm plantation without processing plant unit, is potential in supplying metabolisable energy of 1,983,300 Mcal/year, equivalent to a carrying capacity of 3,680 Goat Units/year . In order to fill the export market to Malaysia, a number of 10 units of medium sized plantation with small scale plant processing or a

  12. Product model structure for generalized optimal design

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The framework of the generalized optimization product model with the core of network- and tree-hierarchical structure is advanced to improve the characteristics of the generalized optimal design. Based on the proposed node-repetition technique, a network-hierarchical structure is united with the tree-hierarchical structure to facilitate the modeling of serialization and combination products. The criteria for product decomposition are investigated. Seven tree nodes are defined for the construction of a general product model, and their modeling properties are studied in detail. The developed product modeling system is applied and examined successfully in the modeling practice of the generalized optimal design for a hydraulic excavator.

  13. Price Relationships in the Petroleum Market: An Analysis of Crude Oil and Refined Product Prices

    Energy Technology Data Exchange (ETDEWEB)

    Asche, Frank; Gjoelberg, Ole; Voelker, Teresa

    2001-08-01

    In this paper the relationships between crude oil and refined product prices are investigated in a multivariate framework. This allows us to test several (partly competing) assumptions of earlier studies. In particular, we find that the crude oil price is weakly exogenous and that the spread is constant in some but not all relationships. Moreover, the multivariate analysis shows that the link between crude oil prices and several refined product prices implies market integration for these refined products. This is an example of supply driven market integration and producers will change the output mix in response to price changes. (author)

  14. Alkaline catalyzed biodiesel production from moringa oleifera oil with optimized production parameters

    Energy Technology Data Exchange (ETDEWEB)

    Kafuku, G.; Mbarawa, M. [Department of Mechanical Engineering, Tshwane University of Technology, Private Bag X680, 0001 Pretoria (South Africa)

    2010-08-15

    The utilization of non-edible feedstock such as moringa oleifera for biodiesel production attracts much attention owing to the issue with regards to avoiding a threat to food supplies. In this study, the optimization of biodiesel production parameters for moringa oleifera oil was carried out. The free fatty acid value of moringa oil was found to be 0.6%, rendering the one step alkaline transesterification method for converting moringa fatty acids to their methyl esters possible. The optimum production parameters: catalyst amount, alcohol amount, temperature, agitation speed and reaction time were determined experimentally and found to be: 1.0 wt% catalyst amount, 30 wt% methanol amount, 60 C reaction temperature, 400 rpm agitation rate and 60 min reaction time. With these optimal conditions the conversion efficiency was 82%. The properties of the moringa biodiesel that was produced were observed to fall within the recommended international biodiesel standards. However, moringa biodiesel showed high values of cloud and pour points of 10 C and 3 C respectively, which present a problem as regards use in cold temperatures. (author)

  15. Productivity, Oil Content, and Oil Composition of Sweet Basil as a Function of Nitrogen and Sulfur Fertilization

    Science.gov (United States)

    Nitrogen (N) and sulfur (S) were believed to be important nutrient management tools for the production of sweet basil (Ocimum basilicum L. 'German') with desirable oil content and composition and also acceptable herbage yields. A multi-location research study was initiated to evaluate the effect of...

  16. Analysis of methane production by microorganisms indigenous to a depleted oil reservoir for application in Microbial Enhanced Oil Recovery.

    Science.gov (United States)

    Kobayashi, Hajime; Kawaguchi, Hideo; Endo, Keita; Mayumi, Daisuke; Sakata, Susumu; Ikarashi, Masayuki; Miyagawa, Yoshihiro; Maeda, Haruo; Sato, Kozo

    2012-01-01

    We examined methane production by microorganisms collected from a depleted oilfield. Our results indicated that microorganisms indigenous to the petroleum reservoir could effectively utilize yeast extract, suggesting that the indigenous microorganisms and proteinaceous nutrients could be recruitable for Microbially Enhanced Oil Recovery. Copyright © 2011 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

  17. Plant-wide Control for Better De-oiling of Produced Water in Offshore Oil & Gas Production

    DEFF Research Database (Denmark)

    Yang, Zhenyu; Stigkær, Jens Peter; Løhndorf, Bo

    2013-01-01

    This paper discusses the application of plant-wide control philosophy to enhance the performance and capacity of the Produced Water Treatment (PWT) in offshore oil & gas production processes. Different from most existing facility- or material-based PWT innovation methods, the objective of this work...

  18. Sophorolipids production by Candida bombicola ATCC 22214 and its potential application in microbial enhanced oil recovery

    Directory of Open Access Journals (Sweden)

    Abdulkadir E. Elshafie

    2015-11-01

    Full Text Available Biosurfactant production using Candida bombicola ATCC 22214, its characterization and potential applications in enhancing oil recovery was studied at laboratory scale. The seed media and the production media were standardized for optimal growth and biosurfactant production. The production media were tested with different carbon sources: glucose (2%w/v and, corn oil (10%v/v added separately or concurrently. The samples were collected at 24h interval up to 120h and checked for growth (OD660, and biosurfactant production (Surface tension and Interfacial tension. The medium with both glucose and corn oil gave better biosurfactant production and reduced both surface tension and interfacial tension to 28.56 + 0.42mN/m and 2.13 + 0.09mN/m, respectively within 72h. The produced biosurfactant was quite stable at 13-15% salinity, pH range of 2-12, and at temperature up to 100°C. It also produced stable emulsions (%E24 with different hydrocarbons (pentane, hexane, heptane, tridecane, tetradecane, hexadecane, 1-methylnaphthalene, 2,2,4,4,6,8-heptamethylnonane, light and heavy crude oil. The produced biosurfactant was extracted using ethyl acetate and characterized as a mixture of sophorolipids. The potential of sophorolipids in enhancing oil recovery was tested using core-flooding experiments, under reservoir conditions, where additional 27.27% of residual oil (Sor was recovered. This confirmed the potential of sophorolipids for applications in microbial enhanced oil recovery.

  19. Sophorolipids Production by Candida bombicola ATCC 22214 and its Potential Application in Microbial Enhanced Oil Recovery.

    Science.gov (United States)

    Elshafie, Abdulkadir E; Joshi, Sanket J; Al-Wahaibi, Yahya M; Al-Bemani, Ali S; Al-Bahry, Saif N; Al-Maqbali, Dua'a; Banat, Ibrahim M

    2015-01-01

    Biosurfactant production using Candida bombicola ATCC 22214, its characterization and potential applications in enhancing oil recovery were studied at laboratory scale. The seed media and the production media were standardized for optimal growth and biosurfactant production. The production media were tested with different carbon sources: glucose (2%w/v) and corn oil (10%v/v) added separately or concurrently. The samples were collected at 24 h interval up to 120 h and checked for growth (OD660), and biosurfactant production [surface tension (ST) and interfacial tension (IFT)]. The medium with both glucose and corn oil gave better biosurfactant production and reduced both ST and IFT to 28.56 + 0.42mN/m and 2.13 + 0.09mN/m, respectively within 72 h. The produced biosurfactant was quite stable at 13-15% salinity, pH range of 2-12, and at temperature up to 100°C. It also produced stable emulsions (%E24) with different hydrocarbons (pentane, hexane, heptane, tridecane, tetradecane, hexadecane, 1-methylnaphthalene, 2,2,4,4,6,8-heptamethylnonane, light and heavy crude oil). The produced biosurfactant was extracted using ethyl acetate and characterized as a mixture of sophorolipids (SPLs). The potential of SPLs in enhancing oil recovery was tested using core-flooding experiments under reservoir conditions, where additional 27.27% of residual oil (Sor) was recovered. This confirmed the potential of SPLs for applications in microbial enhanced oil recovery.

  20. INCREASING HEAVY OIL RESERVES IN THE WILMINGTON OIL FIELD THROUGH ADVANCED RESERVOIR CHARACTERIZATION AND THERMAL PRODUCTION TECHNOLOGIES

    Energy Technology Data Exchange (ETDEWEB)

    Unknown

    2001-08-08

    The objective of this project is to increase the recoverable heavy oil reserves within sections of the Wilmington Oil Field, near Long Beach, California, through the testing and application of advanced reservoir characterization and thermal production technologies. The hope is that successful application of these technologies will result in their implementation throughout the Wilmington Field and, through technology transfer, will be extended to increase the recoverable oil reserves in other slope and basin clastic (SBC) reservoirs. The existing steamflood in the Tar zone of Fault Block II-A (Tar II-A) has been relatively inefficient because of several producibility problems which are common in SBC reservoirs: inadequate characterization of the heterogeneous turbidite sands, high permeability thief zones, low gravity oil and non-uniform distribution of the remaining oil. This has resulted in poor sweep efficiency, high steam-oil ratios, and early steam breakthrough. Operational problems related to steam breakthrough, high reservoir pressure, and unconsolidated sands have caused premature well and downhole equipment failures. In aggregate, these reservoir and operational constraints have resulted in increased operating costs and decreased recoverable reserves. A suite of advanced reservoir characterization and thermal production technologies are being applied during the project to improve oil recovery and reduce operating costs, including: (1) Development of three-dimensional (3-D) deterministic and stochastic reservoir simulation models--thermal or otherwise--to aid in reservoir management of the steamflood and post-steamflood phases and subsequent development work. (2) Development of computerized 3-D visualizations of the geologic and reservoir simulation models to aid reservoir surveillance and operations. (3) Perform detailed studies of the geochemical interactions between the steam and the formation rock and fluids. (4) Testing and proposed application of a

  1. Lipase production by yeasts from extra virgin olive oil.

    Science.gov (United States)

    Ciafardini, G; Zullo, B A; Iride, A

    2006-02-01

    Newly produced olive oil has an opalescent appearance due to the presence of solid particles and micro-drops of vegetation water from the fruits. Some of our recent microbiological research has shown that a rich micro-flora is present in the suspended fraction of the freshly produced olive oil capable of improving the quality of the oil through the hydrolysis of the oleuropein. Present research however has, for the first time, demonstrated the presence of lipase-positive yeasts in some samples of extra virgin olive oil which can lower the quality of the oil through the hydrolysis of the triglycerides. The tests performed with yeasts of our collection, previously isolated from olive oil, demonstrated that two lipase-producing yeast strains named Saccharomyces cerevisiae 1525 and Williopsis californica 1639 were able to hydrolyse different specific synthetic substrates represented by p-nitrophenyl stearate, 4-nitrophenyl palmitate, tripalmitin and triolein as well as olive oil triglycerides. The lipase activity in S. cerevisiae 1525 was confined to the whole cells, whereas in W. californica 1639 it was also detected in the extracellular fraction. The enzyme activity in both yeasts was influenced by the ratio of the aqueous to the organic phase reaching its maximum value in S. cerevisiae 1525 when the water added to the olive oil was present in a ratio of 0.25% (v/v), whereas in W. californica 1639 the optimal ratio was 1% (v/v). Furthermore, the free fatty acids of olive oil proved to be good inducers of lipase activity in both yeasts. The microbiological analysis carried out on commercial extra virgin olive oil, produced in four different geographic areas, demonstrated that the presence of lipase-producing yeast varied from zero to 56% of the total yeasts detected, according to the source of oil samples. The discovery of lipase-positive yeasts in some extra virgin olive oils leads us to believe that yeasts are able to contribute in a positive or negative way towards

  2. Western oil-shale development: a technology assessment. Volume 2: technology characterization and production scenarios

    Energy Technology Data Exchange (ETDEWEB)

    1982-01-01

    A technology characterization of processes that may be used in the oil shale industry is presented. The six processes investigated are TOSCO II, Paraho Direct, Union B, Superior, Occidental MIS, and Lurgi-Ruhrgas. A scanario of shale oil production to the 300,000 BPD level by 1990 is developed. (ACR)

  3. Exploring land use changes and the role of palm oil production in Indonesia and Malaysia

    NARCIS (Netherlands)

    Wicke, B.|info:eu-repo/dai/nl/306645955; Sikkema, R.|info:eu-repo/dai/nl/110609913; Dornburg, V.|info:eu-repo/dai/nl/189955007; Faaij, A.P.C.|info:eu-repo/dai/nl/10685903X

    2011-01-01

    This study compiles and analyses national-level data on land use change (LUC) and its causes in Indonesia and Malaysia over the past 30 years. The study also explores the role that palm oil has played in past LUC and that projected growth in palm oil production may play in LUC until 2020 and

  4. Exploring land use changes and the role of palm oil production in Indonesia and Malaysia

    NARCIS (Netherlands)

    Wicke, B.; Sikkema, R.; Dornburg, V.; Faaij, A.P.C.

    2011-01-01

    This study compiles and analyses national-level data on land use change (LUC) and its causes in Indonesia and Malaysia over the past 30 years. The study also explores the role that palm oil has played in past LUC and that projected growth in palm oil production may play in LUC until 2020 and suggest

  5. Functional beverage products using caseinate–omega-3 oil-oat beta glucan emulsions

    Science.gov (United States)

    Beverages with soluble dietary fiber and Omega 3 oil are highly desired by health conscious consumers. However, Omega 3 oil is prone to oxidation and accompanying deterioration of sensory profiles; there is an issue to incorporate soluble fiber into beverage products that will not interfere with oxi...

  6. Biodiesel production from sunflower oil by using alkali metal exchanged NaX zeolites

    Energy Technology Data Exchange (ETDEWEB)

    Brito, A.; Borges, M.E.; Hernandez, A. [La Laguna Univ. (Spain)

    2010-07-01

    The aim of this work is to determine the activity of a potassium-acetate exchanges NaX zeolite as catalyst for the transesterification of commercial sunflower oil and frying oil for the production of biodiesel, using a slurry reactor, batch and continuous operation, and testing the effect of some variables on the process. (orig.)

  7. Production of advanced biofuels: Co-processing of upgraded pyrolysis oil in standard refinery units

    NARCIS (Netherlands)

    Miguel Mercader, de F.; Groeneveld, M.J.; Kersten, S.R.A.; Way, N.W.J.; Schaverien, C.J.; Hogendoorn, J.A.

    2010-01-01

    One of the possible process options for the production of advanced biofuels is the co-processing of upgraded pyrolysis oil in standard refineries. The applicability of hydrodeoxygenation (HDO) was studied as a pyrolysis oil upgrading step to allow FCC co-processing. Different HDO reaction end temper

  8. ALOX5 gene variants affect eicosanoid production and response to fish oil supplementation

    Science.gov (United States)

    The objective of this study was to determine whether 5-lipoxygenase (ALOX5) gene variants associated with cardiovascular disease affect eicosanoid production by monocytes. The study was a randomized, double-masked, parallel intervention trial with fish oil (5.0 g of fish oil daily, containing 2.0 g ...

  9. PETROCHINA'S OIL AND GAS PRODUCTION GROWS 5.3 PERCENT IN FIRST THREE QUARTERS

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ PetroChina announced its business results of the first three quarters of 2005 in mid-October. Based on the statistical figures made available from China's No. 1 oil producer, the January-September oil and gas production targets rose 5.3 percent as compared to the same period of the previous year.

  10. On the mechanism by which oil uptake decreases crispy/crunchy behaviour of fried products

    NARCIS (Netherlands)

    Vliet, van T.; Visser, J.E.; Luyten, J.M.J.G.

    2007-01-01

    A large problem for fried snack products with a crispy crust and a soft moist interior is that the crust often loses its crispy character fast, in the order of 3¿20 min. As known during cooling of these snacks adherent oil will be sucked into the crust. The presence of oil in a cellular solid crispy

  11. Construction Starts for China's First Production Line of Coal-based Synthetic Oil

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    @@ On Feb. 22, the foundation-laying ceremony for the Lu'an Coal-based Synthetic Oil Plant, a major component of China's first coal-based synthetic oil demonstration project,was held at Tunliu Coal Mine of the Lu'an Coal Mine Group in north China's Shanxi Province, marking the start of the first such production line in this country.

  12. Processing of coriander fruits for the production of essential oil, triglyceride, and high protein seed meal

    Science.gov (United States)

    Coriander (Coriandrum sativum L.) is a summer annual traditionally grown for use as a fresh green herb or as a spice. The essential oil extracted from coriander fruit is also widely used as flavoring in a variety of food products. The fatty oil (triglyceride) fraction in the seed is rich in petrosel...

  13. The encounter and analysis of naturally occurring radionuclides in gas and oil production and processing

    Energy Technology Data Exchange (ETDEWEB)

    Hartog, F.A.; Jonkers, G.; Knaepen, W.A.I. [Shell Research and Technology Centre, Amsterdam, (Netherlands)

    1996-12-31

    As a result of oil and gas production, radioactive daughter elements from the uranium and thorium decay series can be mobilized and transported away from the reservoir. Due to changes in flow regime, temperature, pressure or chemical environment NORs (Naturally Occurring Radionuclides) may build up in products, by-products or waste streams from gas and oil production and processing facilities. Products containing NORs are commonly denoted by the acronym NORM (Naturally Occurring Radioactive Materials). Main topics of this paper are: E and P (Exploration and Production) NORM characteristics; incentives for NORM analysis; NORM analysis; interlaboratory test programme; analysis techniques; results and conclusions of the test programme. 4 figs., 2 tabs.

  14. Bio-oil upgrading strategies to improve PHA production from selected aerobic mixed cultures.

    Science.gov (United States)

    Moita Fidalgo, Rita; Ortigueira, Joana; Freches, André; Pelica, João; Gonçalves, Magarida; Mendes, Benilde; Lemos, Paulo C

    2014-06-25

    Recent research on polyhydroxyalkanoates (PHAs) has focused on developing cost-effective production processes using low-value or industrial waste/surplus as substrate. One of such substrates is the liquid fraction resulting from pyrolysis processes, bio-oil. In this study, valorisation of bio-oil through PHA production was investigated. The impact of the complex bio-oil matrix on PHA production by an enriched mixed culture was examined. The performance of the direct utilization of pure bio-oil was compared with the utilization of three defined substrates contained in this bio-oil: acetate, glucose and xylose. When compared with acetate, bio-oil revealed lower capacity for polymer production as a result of a lower polymer yield on substrate and a lower PHA cell content. Two strategies for bio-oil upgrade were performed, anaerobic fermentation and vacuum distillation, and the resulting liquid streams were tested for polymer production. The first one was enriched in volatile fatty acids and the second one mainly on phenolic and long-chain fatty acids. PHA accumulation assays using the upgraded bio-oils attained polymer yields on substrate similar or higher than the one achieved with acetate, although with a lower PHA content. The capacity to use the enriched fractions for polymer production has yet to be optimized. The anaerobic digestion of bio-oil could also open-up the possibility to use the fermented bio-oil directly in the enrichment process of the mixed culture. This would increase the selective pressure toward an optimized PHA accumulating culture selection.

  15. The isolation and screening of microalgae for the production of oil

    Directory of Open Access Journals (Sweden)

    Danilović Bojana R.

    2017-01-01

    Full Text Available The biodiesel production has gained increasing attention of the researches in recent years. Current commercial biodiesel production involves transesterification of oil derived from oil crops. Since this production is no more sustainable, the use of microalgae represents a good alternative. Microalgae have high growth rate, high oil content and can be cultured in the environment which are not suitable for agriculture. Additionally, microalgae cultivation improves the reduction of carbon dioxide in the atmosphere. Selection of microalgae for oil production must take into consider certain criteria which include growth rate, oil content, fatty acids profile and ease of separation. In order to analyze the possibility of the use of microalgae for the production of oil, isolation of freshwater microalgae was performed. The isolation was done by the use of traditional techniques from freshwaters near Leskovac. A total number of 6 microalgae strains were isolated and identified as the representatives of the genera Chlorococcum (1 isolate, Chlorella (1 isolate, Scenedesmus (1 isolate and Desmodesmus (3 isolates. Isolates of microalgae were screened for the growth rate, biomass and oil productivity and oil content. The highest content of biomass was 1.5 g/l and it was observed in the strains Chlorococcum sp. and Desmodesmus sp. 1. The highest value of specific growth rate was calculated during the growth of microalgae Chlorella sp., Scenedesmus sp. and Desmodesmus sp.1, while the lowest value was observed for Chlorococcum sp. Oil productivity was the highest for Chlorella sp. and Desmodesmus sp.1 (0,4 g/l and the lowest for Desmodesmus sp.2, Desmodesmus sp.3 and Chlorococcum sp. (0,2 g/l. The oil content was in the range from 15.8% (Chlorococcum sp. to 33% (Chlorella sp. Since the microalgae isolates Chlorella sp. and Scenedesmus sp. had the highest oil productivity, high growth rate and high oil content, these strains are the most suitable for further

  16. Sectoral Structure Change Modeling of European Oil and Gas Producing Country’S Economy

    Directory of Open Access Journals (Sweden)

    Perepelkin Viacheslav Alexandrovich

    2015-12-01

    Full Text Available In this paper, we consider identifying features of sectoral structuring within the national economy that has definite foreign trade product specialization. Examination of the sector-specific division methodology enabled identification of its strong association with certain sector dominance in the economy. It is against this background that we offer an explanation for the delay in transferring from the post-Soviet to the applicable international classification of economic structure elements in Russia and Belarus. We perform analysis of the three-component P-S-T model (primary, secondary, tertiary sector using statistical and econometric methods and define properties of the sectoral shares dynamics in national economies of oil and gas producing countries. Analysis of the Russian and Norwegian economies’ intersectoral changes suggests that it is necessary for the government to develop and implement selective structural policy to overcome the existing structural disproportions.

  17. LIFE CYCLE ASSESSMENT OF VEGETABLE OIL PRODUCTION: A CASE STUDY OF AN OIL MILL IN IBADAN, NIGERIA

    OpenAIRE

    Bamgbade, O A; Omoniyi, T E; Ewemoje, T A

    2016-01-01

    The gate-to-gate study aimed to evaluate the potential environmental impacts associated with the production of vegetable oil and to proffer ways of improving and reducing some of the environmental impacts associated with the production system. This study compared the Life Cycle Impact Assessment (LCIA) of four scenarios; different transportation distances for palm kernel materials and different type of fuel used in the boiler. The LCIA was conducted using Gabi 6 and Tool for the Reduction and...

  18. Acid-catalyzed production of biodiesel from waste frying oil

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, S.; Dube, M.A.; McLean, D.D. [Department of Chemical Engineering, University of Ottawa, Ottawa, ON (Canada); Kates, M. [Department of Biochemistry, Microbiology and Immunology, University of Ottawa, Ottawa, ON (Canada)

    2006-03-15

    The reaction kinetics of acid-catalyzed transesterification of waste frying oil in excess methanol to form fatty acid methyl esters (FAME), for possible use as biodiesel, was studied. Rate of mixing, feed composition (molar ratio oil:methanol:acid) and temperature were independent variables. There was no significant difference in the yield of FAME when the rate of mixing was in the turbulent range 100 to 600rpm. The oil:methanol:acid molar ratios and the temperature were the most significant factors affecting the yield of FAME. At 70{sup o}C with oil:methanol:acid molar ratios of 1:245:3.8, and at 80{sup o}C with oil:methanol:acid molar ratios in the range 1:74:1.9-1:245:3.8, the transesterification was essentially a pseudo-first-order reaction as a result of the large excess of methanol which drove the reaction to completion (99+/-1% at 4h). In the presence of the large excess of methanol, free fatty acids present in the waste oil were very rapidly converted to methyl esters in the first few minutes under the above conditions. Little or no monoglycerides were detected during the course of the reaction, and diglycerides present in the initial waste oil were rapidly converted to FAME. (author)

  19. Technical aspects of biodiesel production from vegetable oils

    Directory of Open Access Journals (Sweden)

    Krishnakumar Janahiraman

    2008-01-01

    Full Text Available Biodiesel, a promising substitute as an alternative fuel has gained significant attention due to the finite nature of fossil energy sources and does not produce sulfur oxides and minimize the soot particulate in comparison with the existing one from petroleum diesel. The utilization of liquid fuels such as biodiesel produced from vegetable oil by transesterification process represents one of the most promising options for the use of conventional fossil fuels. In the first step of this experimental research, edible rice bran oil used as test material and converted into methyl ester and non-edible jatropha vegetable oil is converted into jatropha oil methyl ester, which are known as biodiesel and they are prepared in the presence of homogeneous acid catalyst and optimized their operating parameters like reaction temperature, quantity of alcohol and the catalyst requirement, stirring rate and time of esterification. In the second step, the physical properties such as density, flash point, kinematic viscosity, cloud point, and pour point were found out for the above vegetable oils and their methyl esters. The same characteristics study was also carried out for the diesel fuel for obtaining the baseline data for analysis. The values obtained from the rice bran oil methyl ester and jatropha oil methyl ester are closely matched with the values of conventional diesel and it can be used in the existing diesel engine without any hardware modification. In the third step the storage characteristics of biodiesel are also studied. .

  20. Increasing Heavy Oil in the Wilmington Oil Fiel Through Advanced Reservoir Characterization and Thermal Production Technologies. Annual Report, March 30, 1995--March 31, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Allison, Edith

    1996-12-01

    The objective of this project is to increase heavy oil reserves in a portion of the Wilmington Oil Field, near Long Beach, California, by implementing advanced reservoir characterization and thermal production technologies. Based on the knowledge and experience gained with this project, these technologies are intended to be extended to other sections of the Wilmington Oil Field, and, through technology transfer, will be available to increase heavy oil reserves in other slope and basin clastic (SBC) reservoirs.

  1. Pyrolysis of hazelnut shells in a fixed-bed tubular reactor. Yields and structural analysis of bio-oil

    Energy Technology Data Exchange (ETDEWEB)

    Puetuen, A.E.; Oezcan, A.; Puetuen, E. [Department of Chemical Engineering, Faculty of Engineering and Architecture, Yunusemre Campus, Anadolu University, 26470 Eskisehir (Turkey)

    1999-09-01

    Fixed-bed pyrolysis experiments have been conducted on a sample of hazelnut shells to determine the possibility of being a potential source of renewable fuels and chemical feedstocks. The effects of pyrolysis temperature and well-sweep gas atmosphere (N{sub 2}) on the pyrolysis yields and chemical compositions have been investigated. The maximum bio-oil yield of 23.1 wt.% was obtained in N{sub 2} atmosphere at a pyrolysis temperature of 500C and heating rate of 7 K min{sup -1}. The pyrolysis products were characterised by elemental analysis and various chromatographic and spectroscopic techniques and also compared with currently utilised transport fuels by simulated distillation. Bio-oil was then fractionated into pentane soluble and insoluble compounds (asphaltenes). Pentane soluble was then solvent fractionated into pentane, toluene, ether and methanol subfractions by fractionated column chromatography. The aliphatic and low-molecular-weight aromatic subfractions of the bio-oil were then analyzed by capillary column gas-liquid chromatography and GC/MS. Further structural analysis of bio-oil and aromatic and polar subfractions FTIR and {sup 1}H-NMR spectra were obtained. The chemical characterization has shown that the bio-oil obtained from hazelnut shells was quite similar to the crude oil and shale oil

  2. Production of biodiesel from sunflower oil and ethanol by base catalyzed transesterification

    OpenAIRE

    Sales, Alejandro

    2011-01-01

    Biodiesel is an attractive alternative fuel for diesel engines.The feedstock for biodiesel production is usually vegetable oil, pure oil or waste cooking oil, or animal fats The most common way today to produce biodiesel is by transesterification of the oils with an alcohol in the presence of an alkaline catalyst. It is a low temperature and low-pressure reaction. It yields high conversion (96%-98%) with minimal side reactions and short reaction time. It is a direct conversion to biodiesel wi...

  3. Can fruit-form be a marker for argan oil production?

    Science.gov (United States)

    Gharby, Saïd; Harhar, Hicham; Kartah, Badr Eddine; El Monfalouti, Hanae; Denhez, Clément; Hilali, Miloudi; Guillaume, Dom; Charrouf, Zoubida

    2013-01-01

    Deforestation is an important matter for the argan forest whose preservation necessitates planting trees. Macroscopic parameters are urgently needed to identify trees presenting good potential as oil producers. This study demonstrates that argan oil produced from kernels of apiculate fruit is richer in d-tocopherol, whereas oil produced from spherical fruit is richer in linoleic acid, and that produced from fusiform fruit is richer in oleic acid. Therefore, the use of fruit-form as a marker could permit an easy organic production of "naturally enriched" oils.

  4. Production of bio-oil with flash pyrolysis; Biooeljyn tuotanto flash-pyrolyysillae ja sen poltto

    Energy Technology Data Exchange (ETDEWEB)

    Nyroenen, T. [Vapo Oy, Jyvaeskylae (Finland)

    1997-12-01

    The target of the R and D work is to study the production of bio-oils using Flash-pyrolysis technology and utilisation of the bio-oil in oil-fuelled boilers. The PDU-unit was installed at VTT Energy in Otaniemi in April 1996. The first test were carried out in June. In the whole project Vapo Oy is responsible for: acquiring the 20 kg/h PDU-device for development; follow up of the engine tests; the investment of 5 MW demonstration plant; to carry on the boiler and engine tests with Finnish bio-oils. (orig.)

  5. Refining oil production in the latter stage of developing deposits

    Energy Technology Data Exchange (ETDEWEB)

    Dzhakiyev, K.T.; Balgimbayev, M.B.

    1983-01-01

    Certain characteristics of the Emba high viscosity oil deposits are examined. Experience in the development of the deposits which are in the latter stage show that despite the high relationships of the viscosities of the oil and water in the examined deposits, quite high values have been achieved. An orderly approach to refining the balanced reserves based on factual data from exploitation of the deposits is approached. The relationship between the accumulated withdrawals of oil and fluid, acquired as applied to Emba deposits, and the displacement factor, determined from factual data on the basis of a theory of full scale modeling, are used for this purpose.

  6. Integrated oil production and upgrading using molten alkali metal

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, John Howard

    2016-10-04

    A method that combines the oil retorting process (or other process needed to obtain/extract heavy oil or bitumen) with the process for upgrading these materials using sodium or other alkali metals. Specifically, the shale gas or other gases that are obtained from the retorting/extraction process may be introduced into the upgrading reactor and used to upgrade the oil feedstock. Also, the solid materials obtained from the reactor may be used as a fuel source, thereby providing the heat necessary for the retorting/extraction process. Other forms of integration are also disclosed.

  7. Integrated oil production and upgrading using molten alkali metal

    Science.gov (United States)

    Gordon, John Howard

    2016-10-04

    A method that combines the oil retorting process (or other process needed to obtain/extract heavy oil or bitumen) with the process for upgrading these materials using sodium or other alkali metals. Specifically, the shale gas or other gases that are obtained from the retorting/extraction process may be introduced into the upgrading reactor and used to upgrade the oil feedstock. Also, the solid materials obtained from the reactor may be used as a fuel source, thereby providing the heat necessary for the retorting/extraction process. Other forms of integration are also disclosed.

  8. Oil Depletion and the Energy Efficiency of Oil Production: The Case of California

    Directory of Open Access Journals (Sweden)

    Adam R. Brandt

    2011-10-01

    Full Text Available This study explores the impact of oil depletion on the energetic efficiency of oil extraction and refining in California. These changes are measured using energy return ratios (such as the energy return on investment, or EROI. I construct a time-varying first-order process model of energy inputs and outputs of oil extraction. The model includes factors such as oil quality, reservoir depth, enhanced recovery techniques, and water cut. This model is populated with historical data for 306 California oil fields over a 50 year period. The model focuses on the effects of resource quality decline, while technical efficiencies are modeled simply. Results indicate that the energy intensity of oil extraction in California increased significantly from 1955 to 2005. This resulted in a decline in the life-cycle EROI from 6.5 to 3.5 (measured as megajoules (MJ delivered to final consumers per MJ primary energy invested in energy extraction, transport, and refining. Most of this decline in energy returns is due to increasing need for steam-based thermal enhanced oil recovery, with secondary effects due to conventional resource depletion (e.g., increased water cut.

  9. Novel bio-based thermoset resins based on epoxidized vegetable oils for structural adhesives

    Science.gov (United States)

    Sivasubramanian, Shivshankar

    Conventional engineered wood composites are bonded for the most part through formaldehyde-based structural adhesives such as urea formaldehyde (UF), melamine formaldehyde (MF), phenol formaldehyde (PF) and resorcinol formaldehyde (RF). Formaldehyde is a known human carcinogen; the occupational exposure and emission after manufacturing of these binders is raising more and more concern. With increasing emphasis on environmental issues, there is clear incentive to replace these hazardous conventional formaldehyde-based binders with cco-friendly resins having similar properties but derived from renewable sources, bearing in mind the economics of the structural wood composite industry. In this thesis, the curing reaction of bio-derived epoxy thermosets with inexpensive, low-toxicity precursors, including polyimines and amino acids was investigated. Epoxidized linseed oil (ELO) and epoxidized soybean oil (ESO) were successfully crosslinked with both branched polyethyleneimine (PEI) and triethylenetetramine (fETA). Epoxidized castor oil (ECO) was crosslinked with polyethyleneimine (PEI), having different molecular weights. Curing conditions were optimized through solvent uptake and soluble fraction analysis. Finally, the mechanical properties of the optimized compositions of rigid bioepoxies were evaluated using dynamic mechanical rheological testing (DMRT). While not as stiff as conventional materials, optimized materials have sufficient room temperature moduli to show promise for coatings and as binders in engineered wood products.

  10. Biobased Fat Mimicking Molecular Structuring Agents for Medium-Chain Triglycerides (MCTs) and Other Edible Oils.

    Science.gov (United States)

    Silverman, Julian R; John, George

    2015-12-01

    To develop sustainable value-added materials from biomass, novel small-molecule sugar ester gelators were synthesized using biocatalysis. The facile one-step regiospecific coupling of the pro-antioxidant raspberry ketone glucoside and unsaturated or saturated long- and medium-chain fatty acids provides a simple approach to tailor the structure and self-assembly of the amphiphilic product. These low molecular weight molecules demonstrated the ability to self-assemble in a variety of solvents and exhibited supergelation, with a minimum gelation concentration of 0.25 wt %, in numerous organic solvents, as well as in a range of natural edible oils, specifically a relatively unstudied group of liquids: natural medium-chain triglyceride oils, notably coconut oil. Spectroscopic analysis details the gelator structure as well as the intermolecular noncovalent interactions, which allow for gelation. X-ray diffraction studies indicate fatty acid chain packing of gelators is similar to that of natural fats, signifying the crystalline nature may lead to desirable textural properties and mouthfeel.

  11. Impact of Expanded North Slope of Alaska Crude Oil Production on Oil Flows in the Contiguous United States (Summary)

    Energy Technology Data Exchange (ETDEWEB)

    DeRosa, Sean e. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Flanagan, Tatiana Paz [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-05-01

    Crude oil produced on the North Slope of Alaska (NSA) is primarily transported on the Trans-Alaska Pipeline System (TAPS) to in-state refineries and the Valdez Marine Terminal in southern Alaska. From the Terminal, crude oil is loaded onto tankers and is transported to export markets or to three major locations along the U.S. West Coast: Anacortes-Ferndale area (Washington), San Francisco Bay area, and Los Angeles area. North Slope of Alaska production has decreased about 75% since the 1980s, which has reduced utilization of TAPS.

  12. Recovery of Bio-Oil from Industrial Food Waste by Liquefied Dimethyl Ether for Biodiesel Production

    Directory of Open Access Journals (Sweden)

    Kiyoshi Sakuragi

    2016-02-01

    Full Text Available The development of new energy sources has become particularly important from the perspective of energy security and environmental protection. Therefore, the utilization of waste resources such as industrial food wastes (IFWs in energy production is expected. The central research institute of electric power industry (CRIEPI, Tokyo, Japan has recently developed an energy-saving oil-extraction technique involving the use of liquefied dimethyl ether (DME, which is an environmentally friendly solvent. In this study, three common IFWs (spent coffee grounds, soybean, and rapeseed cakes were evaluated with respect to oil yield for biodiesel fuel (BDF production by the DME extraction method. The coffee grounds were found to contain 16.8% bio-oil, whereas the soybean and rapeseed cakes contained only approximately 0.97% and 2.6% bio-oil, respectively. The recovered oils were qualitatively analysed by gas chromatography-mass spectrometry. The properties of fatty acid methyl esters derived from coffee oil, such as kinematic viscosity, pour point, and higher heating value (HHV, were also determined. Coffee grounds had the highest oil content and could be used as biofuel. In addition, the robust oil extraction capability of DME indicates that it may be a favourable alternative to conventional oil extraction solvents.

  13. Comparison Between Different Flavored Olive Oil Production Techniques: Healthy Value and Process Efficiency.

    Science.gov (United States)

    Clodoveo, Maria Lisa; Dipalmo, Tiziana; Crupi, Pasquale; Durante, Viviana; Pesce, Vito; Maiellaro, Isabella; Lovece, Angelo; Mercurio, Annalisa; Laghezza, Antonio; Corbo, Filomena; Franchini, Carlo

    2016-03-01

    Three different flavoring methods of olive oil were tested employing two different herbs, thyme and oregano. The traditional method consist in the infusion of herbs into the oil. A second scarcely diffused method is based on the addition of herbs to the crushed olives before the malaxation step during the extraction process. The third innovative method is the implementation of the ultrasound before the olive paste malaxation. The objective of the study is to verify the effect of the treatments on the quality of the product, assessed by means of the chemical characteristics, the phenol composition and the radical scavenging activity of the resulting oils. The less favorable method was the addition of herbs directly to the oil. A positive effect was achieved by the addition of herbs to the olive paste and other advantages were attained by the employment of ultrasound. These last two methods allow to produce oils "ready to sell", instead the infused oils need to be filtered. Moreover, the flavoring methods applied during the extraction process determine a significant increment of phenolic content and radical scavenging activity of olive oils. The increments were higher when oregano is used instead of thyme. Ultrasound inhibited the olive polyphenoloxidase, the endogenous enzyme responsible for olive oil phenol oxidation. This treatment of olive paste mixed with herbs before malaxation was revealed as the most favorable method due to the best efficiency, reduced time consumption and minor labor, enhancing the product quality of flavored olive oil.

  14. Progressive degradation of crude oil n-alkanes coupled to methane production under mesophilic and thermophilic conditions.

    Science.gov (United States)

    Cheng, Lei; Shi, Shengbao; Li, Qiang; Chen, Jianfa; Zhang, Hui; Lu, Yahai

    2014-01-01

    Although methanogenic degradation of hydrocarbons has become a well-known process, little is known about which crude oil tend to be degraded at different temperatures and how the microbial community is responded. In this study, we assessed the methanogenic crude oil degradation capacity of oily sludge microbes enriched from the Shengli oilfield under mesophilic and thermophilic conditions. The microbial communities were investigated by terminal restriction fragment length polymorphism (T-RFLP) analysis of 16S rRNA genes combined with cloning and sequencing. Enrichment incubation demonstrated the microbial oxidation of crude oil coupled to methane production at 35 and 55°C, which generated 3.7±0.3 and 2.8±0.3 mmol of methane per gram oil, respectively. Gas chromatography-mass spectrometry (GC-MS) analysis revealed that crude oil n-alkanes were obviously degraded, and high molecular weight n-alkanes were preferentially removed over relatively shorter-chain n-alkanes. Phylogenetic analysis revealed the concurrence of acetoclastic Methanosaeta and hydrogenotrophic methanogens but different methanogenic community structures under the two temperature conditions. Candidate divisions of JS1 and WWE 1, Proteobacteria (mainly consisting of Syntrophaceae, Desulfobacteraceae and Syntrophorhabdus) and Firmicutes (mainly consisting of Desulfotomaculum) were supposed to be involved with n-alkane degradation in the mesophilic conditions. By contrast, the different bacterial phylotypes affiliated with Caldisericales, "Shengli Cluster" and Synergistetes dominated the thermophilic consortium, which was most likely to be associated with thermophilic crude oil degradation. This study revealed that the oily sludge in Shengli oilfield harbors diverse uncultured microbes with great potential in methanogenic crude oil degradation over a wide temperature range, which extend our previous understanding of methanogenic degradation of crude oil alkanes.

  15. Progressive degradation of crude oil n-alkanes coupled to methane production under mesophilic and thermophilic conditions.

    Directory of Open Access Journals (Sweden)

    Lei Cheng

    Full Text Available Although methanogenic degradation of hydrocarbons has become a well-known process, little is known about which crude oil tend to be degraded at different temperatures and how the microbial community is responded. In this study, we assessed the methanogenic crude oil degradation capacity of oily sludge microbes enriched from the Shengli oilfield under mesophilic and thermophilic conditions. The microbial communities were investigated by terminal restriction fragment length polymorphism (T-RFLP analysis of 16S rRNA genes combined with cloning and sequencing. Enrichment incubation demonstrated the microbial oxidation of crude oil coupled to methane production at 35 and 55°C, which generated 3.7±0.3 and 2.8±0.3 mmol of methane per gram oil, respectively. Gas chromatography-mass spectrometry (GC-MS analysis revealed that crude oil n-alkanes were obviously degraded, and high molecular weight n-alkanes were preferentially removed over relatively shorter-chain n-alkanes. Phylogenetic analysis revealed the concurrence of acetoclastic Methanosaeta and hydrogenotrophic methanogens but different methanogenic community structures under the two temperature conditions. Candidate divisions of JS1 and WWE 1, Proteobacteria (mainly consisting of Syntrophaceae, Desulfobacteraceae and Syntrophorhabdus and Firmicutes (mainly consisting of Desulfotomaculum were supposed to be involved with n-alkane degradation in the mesophilic conditions. By contrast, the different bacterial phylotypes affiliated with Caldisericales, "Shengli Cluster" and Synergistetes dominated the thermophilic consortium, which was most likely to be associated with thermophilic crude oil degradation. This study revealed that the oily sludge in Shengli oilfield harbors diverse uncultured microbes with great potential in methanogenic crude oil degradation over a wide temperature range, which extend our previous understanding of methanogenic degradation of crude oil alkanes.

  16. PROTOTYPIC CONTINUITY METHODS FOR FASTER RECOVERY OF OIL PRODUCTS SUPPLY AFTER GREAT QUAKE

    Science.gov (United States)

    Yasuno, Takato

    In the Great East Japan Earthquake, some oil product farms and tanks had a lot of damages. Then we temporally run short of oil products such as gasoline, lamp oil. The oil product is indispensable to make cargo shipment, or rescue operations, and some trouble must come for everyday shopping and movement of business. The lifeline damages come out electric power, water service, gas and communication. In addition the oil product shortage overlaps then the importance to restore was recognized. After earthquake disaster, there is a possibility to interrupt supply services such as shipping from oil tanks and sale at stations. Even if their discontinuation comes, it needs some business continuity policies in order to recover supply service at early stage. This paper grasps oil product discontinuation of supply and restoration transition and tries to get disaster lessons. This paper proposes prototypic techniques to minimize the sum of penalties to supply no service for neighbor region with capacities of critical stations. It applies to Tohoku regions and their gas stations and comments the usefulness of techniques and implication of supply service continuity policy.

  17. Co-combustion of waste from olive oil production with coal in a fluidised bed.

    Science.gov (United States)

    Cliffe, K R; Patumsawad, S

    2001-01-01

    Waste from olive oil production was co-fired with coal in a fluidised bed combustor to study the feasibility of using this waste as an energy source. The combustion efficiency and CO emission were investigated and compared to those of burning 100% of coal. Olive oil waste with up to 20% mass concentration can be co-fired with coal in a fluidised bed combustor designed for coal combustion with a maximum drop of efficiency of 5%. A 10% olive oil waste concentration gave a lower CO emission than 100% coal firing due to improved combustion in the freeboard region. A 20% olive oil waste mixture gave a higher CO emission than both 100% coal firing and 10% olive oil waste mixture, but the combustion efficiency was higher than the 10% olive oil waste mixture due to lower elutriation from the bed.

  18. Optimization of the production of biodiesel from soybean oil by ultrasound assisted methanolysis

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Francisco F.P.; Fernandes, Fabiano A.N. [Universidade Federal do Ceara, Departamento de Engenharia Quimica, Campus do Pici, Bloco 709, 60455-760 Fortaleza-CE (Brazil); Rodrigues, Sueli [Universidade Federal do Ceara, Departamento de Tecnologia dos Alimentos, Campus do Pici, Bloco 858, Caixa Postal 12168, 60421-970 Fortaleza-CE (Brazil)

    2009-02-15

    This paper evaluates and optimizes the production of biodiesel from soybean oil and methanol using sodium hydroxide as catalyst. The study and optimization was carried out at low catalyst concentration (0.2 to 0.6 w/w). The reaction was carried out with application of low-frequency high-intensity ultrasound under atmospheric pressure and ambient temperature in a batch reactor. Response surface methodology (RSM) was used to evaluate the influence of methanol to oil ratio and catalyst concentration on soybean oil conversion into biodiesel. Analysis of the operating conditions by RSM showed that the most important operating condition affecting the reaction was the methanol to oil ratio, while catalyst amount showed little significance in the transesterification reaction. Total consumption of oil was obtained when alcohol to oil ratio of 9:1 and catalyst concentration of 0.2 w/w were applied. (author)

  19. Glyceride structure and sterol composition of SOS-7 halophyte oil

    Directory of Open Access Journals (Sweden)

    El-Shami, S. M.

    1991-06-01

    Full Text Available Glyceride structure of SOS-7 halophyte oil was studied using the lipase hydrolysis technique. This halophyte sample was obtained from 1988 harvest planted in Ghardaka, on the border of the Red Sea, Egypt. The oilseed was ground and extracted for its oil using commercial hexane in Soxhlet extractor. The unsaturated fatty acids were found centralized in the 2-position of triglycerides, whereas oleic and linolenic acids showed more preference for this position. It was found that P3 was the major component of GS3, whereas P2L and PStL; PL2, POL and StL2 are predominating among GS2U and GSU3 respectively. L3 manifested itself as the principal constituent of GU3 type. Sterol composition of the halophyte oil was determined by GLC as TMS derivative. It was found that the oil contains campsterol, β-sitosterol, stigmasterol and 7-stigmasterol of which 7-stigmasterol is the major sterol and constitute 52.4%.

    Se ha estudiado usando la técnica de hidrólisis mediante lipasa la estructura glicerídica de aceite de halofito SOS-7. Esta muestra de halofito fue obtenida a partir de una cosecha de 1988 plantada en Ghardaka, en la orilla del Mar Rojo, Egipto. Para la extracción del aceite de la semilla molida se utilizó hexano comercial en extractor Soxhlet. Los ácidos grasos insaturados se encontraron centralizados en la posición 2 de los triglicéridos, siendo los ácidos oleico y linolénico los que mostraron mayor preferencia por esta posición. Se encontró que P3 fue el componente mayoritario de GS3, mientras que P2L y PStL; PL2 POL y StL2 son los predominantes para GS2U y GSU3 respectivamente. L3 se manifestó como el principal constituyente de los GU3. La composición esterólica del aceite de halofito se determinó por GLC como derivados del

  20. Fast pyrolysis of microalgae remnants in a fluidized bed reactor for bio-oil and biochar production.

    Science.gov (United States)

    Wang, Kaige; Brown, Robert C; Homsy, Sally; Martinez, Liliana; Sidhu, Sukh S

    2013-01-01

    In this study, pyrolysis of microalgal remnants was investigated for recovery of energy and nutrients. Chlorella vulgaris biomass was first solvent-extracted for lipid recovery then the remnants were used as the feedstock for fast pyrolysis experiments using a fluidized bed reactor at 500 °C. Yields of bio-oil, biochar, and gas were 53, 31, and 10 wt.%, respectively. Bio-oil from C. vulgaris remnants was a complex mixture of aromatics and straight-chain hydrocarbons, amides, amines, carboxylic acids, phenols, and other compounds with molecular weights ranging from 70 to 1200 Da. Structure and surface topography of the biochar were analyzed. The high inorganic content (potassium, phosphorous, and nitrogen) of the biochar suggests it may be suitable to provide nutrients for crop production. The bio-oil and biochar represented 57% and 36% of the energy content of the microalgae remnant feedstock, respectively.