Can a GIS toolbox assess the environmental risk of oil spills? Implementation for oil facilities in harbors.

Science.gov (United States)

Valdor, Paloma F; Gómez, Aina G; Velarde, Víctor; Puente, Araceli

2016-04-01

Oil spills are one of the most widespread problems in port areas (loading/unloading of bulk liquid, fuel supply). Specific environmental risk analysis procedures for diffuse oil sources that are based on the evolution of oil in the marine environment are needed. Diffuse sources such as oil spills usually present a lack of information, which makes the use of numerical models an arduous and occasionally impossible task. For that reason, a tool that can assess the risk of oil spills in near-shore areas by using Geographical Information System (GIS) is presented. The SPILL Tool provides immediate results by automating the process without miscalculation errors. The tool was developed using the Python and ArcGIS scripting library to build a non-ambiguous geoprocessing workflow. The SPILL Tool was implemented for oil facilities at Tarragona Harbor (NE Spain) and validated showing a satisfactory correspondence (around 0.60 RSR error index) with the results obtained using a 2D calibrated oil transport numerical model. Copyright © 2016 Elsevier Ltd. All rights reserved.

A Dry-Slip Facility for Fish Terminals on Open Coasts

DEFF Research Database (Denmark)

Burcharth, Hans F.; Schmidt, Jens- Chr.; Odoom, Daniel Semanu

The paper describes a low cost facility for landing and shipping of fish and for bringing fishing boats ashore in periods of bad weather. The facility is meant for open coasts and represents an improvement from beach landing. Being a wooden pile structure it is much cheaper to construct than conv...

A new concept for improved oil spill containment in open waters

International Nuclear Information System (INIS)

Sethness, E.D. Jr.

1990-01-01

In this paper a new concept for improved oil spill containment in open waters is presented. The proposed system is a combination oil boom and wave barrier. Waveguard International has taken its extensive experience as a designer of floating breakwaters and applied this knowledge into the design of a readily transportable, readily deployable floating oil boom with integrated wave attenuation capabilities as well. The new concept is based on the attenuation of the two major natural causes of oil spill dispersion; first, horizontal dispersion caused by wind shear effects; and second, vertical entrainment into the water column caused by the mixing action of wave motion. The physical encirclement of an oil spill with a floating boom to contain horizontal dispersion is not a new concept. Existing systems, however, work best in calm water and rapidly loose efficiency as waves increase. The proposed system can not only physically surround the spill area, but is as much as 90% effective in stopping the transmission of wave energy. The oil boom thus minimizes vertical mixing of the contained oil slick

Biodegradation of uranium-contaminated waste oil

International Nuclear Information System (INIS)

Hary, L.F.

1983-01-01

The Portsmouth Gaseous Diffusion Plant routinely generates quantities of uranium-contaminated waste oil. The current generation rate of waste oil is approximately 2000 gallons per year. The waste is presently biodegraded by landfarming on open field soil plots. However, due to the environmental concerns associated with this treatment process, studies were conducted to determine the optimum biodegradation conditions required for the destruction of this waste. Tests using respirometric flasks were conducted to determine the biodegradation rate for various types of Portsmouth waste oil. These tests were performed at three different loading rates, and on unfertilized and fertilized soil. Additional studies were conducted to evaluate the effectiveness of open field landfarming versus treatment at a greenhouse-like enclosure for the purpose of maintaining soil temperatures above ambient conditions. The respirometric tests concluded that the optimum waste oil loading rate is 10% weight of oil-carbon/weight of soil (30,600 gallons of uranium-contaminated waste oil/acre) on soils with adjusted carbon:nitrogen and carbon:phosphorus ratios of 60:1 and 800:1, respectively. Also, calculational results indicated that greenhouse technology does not provide a significant increase in biodegradation efficiency. Based on these study results, a 6300 ft. 2 abandoned anaerobic digester sludge drying bed is being modified into a permanent waste oil biodegradation facility. The advantage of using this area is that uranium contamination will be contained by the bed's existing leachate collection system. This modified facility will be capable of handling approximately 4500 gallons of waste oil per year; accordingly current waste generation quantities will be satisfactorily treated. 15 refs., 14 figs., 4 tabs

Naturally occurring radioactive materials (NORM) in the oil and gas processing and production facilities

International Nuclear Information System (INIS)

Najera F, J.

1994-01-01

NORM contamination is produced by concentration in petroleum facilities of naturally occurring radioactive materials. The presence of NORM in petroleum reservoirs and in the oil and gas industry has been widely recognized. It's not a critical technical problem if you proceed timely to solve it. NORM is a great but controllable hazard to the human health and the environment, and represents a severe waste management problem. We suggest to the latino american oil companies to conduct studies to detect NORM contamination in their facilities an use to them to plan the appropriate actions to control the situation. (author). 15 refs

Impact of the oil price and fiscal facilities on offshore mining at the Dutch Continental Shelf

International Nuclear Information System (INIS)

Cate, Arie ten; Mulder, Machiel

2007-01-01

The surge in the oil price has raised questions about the magnitude of global reserves of oil. According to some analysts, the current high oil prices indicate a looming decline in the global production of oil. Others believe, however, that the increased level of the oil price encourages exploration and production activities, bringing the oil price to a lower equilibrium level in the near future. In this paper, we assess the impact of the unit profit (depending on the oil price) as well as fiscal facilities on the level of exploration and development drillings in the Dutch Continental Shelf. We conducted an econometric analysis of exploration and development drillings in the Dutch Continental Shelf over the period 1981-2003. Except a few fiscal changes, the regulatory framework for offshore activities in the Netherlands, the so-called 'small fields policy' was unchanged in this period. We find that the expected unit profit based on a moving average of the oil price significantly explains the level of both exploration and development drillings. In addition, the analysis suggests that fiscal facilities have only a temporary effect on exploration activities but are more important for development activities. We conclude that the oil price is a major economic incentive for activities of the mining industry

Atmospheric ammonia mixing ratios at an open-air cattle feeding facility.

Science.gov (United States)

Hiranuma, Naruki; Brooks, Sarah D; Thornton, Daniel C O; Auvermann, Brent W

2010-02-01

Mixing ratios of total and gaseous ammonia were measured at an open-air cattle feeding facility in the Texas Panhandle in the summers of 2007 and 2008. Samples were collected at the nominally upwind and downwind edges of the facility. In 2008, a series of far-field samples was also collected 3.5 km north of the facility. Ammonium concentrations were determined by two complementary laboratory methods, a novel application of visible spectrophotometry and standard ion chromatography (IC). Results of the two techniques agreed very well, and spectrophotometry is faster, easier, and cheaper than chromatography. Ammonia mixing ratios measured at the immediate downwind site were drastically higher (approximately 2900 parts per billion by volume [ppbv]) than thos measured at the upwind site (open-air animal feeding operations, especially under the hot and dry conditions present during these measurements.

The oil and oil services industry international context 2008

International Nuclear Information System (INIS)

Serbutoviez, S.; Silva, C.

2008-11-01

Oil companies rarely do their own major work within the framework of their investments or in the operation of their facilities. They most often act as project coordinators, thereby opening up a vast market for equipment, services and engineering, involving many companies of widely-varying sizes, which constitute the oil services industry. This document provides a panorama of the international oil context in three distinct parts, for 2007, for the first three quarters of 2008, and aspects of trends for 2009. - The first part is devoted to a rapid description of the oil context and the economic environment in which it is evolving. - The second part examines the evolution of world investment in exploration-production (E and P) activities, distinguishing the investments made by oil and oil product/service companies throughout the E and P chain from the more targeted ones of three specific sectors: seismic, drilling and the construction of offshore production equipment. These markets are observed exclusively for oil product/service companies. - The last part is devoted to investments in the refining sector, focusing on the changes in the fundamentals, particularly the equilibrium between refining capacities and medium- term oil demand. This latter analysis involves both oil and oil product/service companies. (authors)

SENSITIVITY OF MOLDS ISOLATED FROM WAREHOUSES OF FOOD PRODUCTION FACILITY ON SELECTED ESSENTIAL OILS

Directory of Open Access Journals (Sweden)

Łukasz Kręcidło

2015-07-01

Full Text Available Storage of raw materials is one of steps in food production chain. The aim of this study was to estimate the influence of selected essential oils on the growth of four fungal strains: Trichoderma viride, Rhizomucor miehei, Penicillium chrysogenum, Penicillium janthinellum. Strains were isolated from warehouses of the food production facility. Selected essential oils: thyme oil, rosewood oil and rosemary oil were used to assess antifungal activity. Chemical composition of essential oils was determined by Gas Chromatography-Mass Spectroscopy (GC-MS. Antifungal activity of essential oils was estimated in relative to peracetic acid (PAA and sterile water with Tween 80 (0,5%. The influence of essential oils on fungal growth was carried by medium poisoning method. Increment of fungal mycelium was measured every day by 10 days. The thyme essential oils totally inhibited fungal growth in the lowest concentration of 1 mm3·cm-3. The most resistant strain was Penicillium janthinellum.

Simulation of helium release in the Battelle Model Containment facility using OpenFOAM

Energy Technology Data Exchange (ETDEWEB)

Wilkening, Heinz; Ammirabile, Luca, E-mail: luca.ammirabile@ec.europa.eu

2013-12-15

Highlights: • The HYJET Jx7 hydrogen release experiment at BMC facility is studied using OpenFOAM. • The SST model and 2nd order numerics for momentum and species concentration are used. • The behaviour is captured well but helium concentration is generally over-predicted. • OpenFOAM needs smaller time steps, higher resolution, more CPU time compared to CFX. • The study shows the potential of open source CFD codes in some nuclear application. - Abstract: The open source CFD code OpenFOAM has been validated against an experiment of jet release phenomena in the Battelle Model Containment facility (BMC), and benchmarked with the Ansys CFX5.7 results. In the selected test, HYJET Jx7, helium was released into the containment at a speed of 42 m/s over a time of 200 s. The SST turbulence model was applied to model helium release and dispersion with both codes. The overall behaviour is captured adequately. However, there are still some noticeable differences between the CFX and OpenFOAM solutions. The study confirms the potential of using open source codes like OpenFOAM in some nuclear applications. Nevertheless further investigations and improvements are needed.

Simulation of helium release in the Battelle Model Containment facility using OpenFOAM

International Nuclear Information System (INIS)

Wilkening, Heinz; Ammirabile, Luca

2013-01-01

Highlights: • The HYJET Jx7 hydrogen release experiment at BMC facility is studied using OpenFOAM. • The SST model and 2nd order numerics for momentum and species concentration are used. • The behaviour is captured well but helium concentration is generally over-predicted. • OpenFOAM needs smaller time steps, higher resolution, more CPU time compared to CFX. • The study shows the potential of open source CFD codes in some nuclear application. - Abstract: The open source CFD code OpenFOAM has been validated against an experiment of jet release phenomena in the Battelle Model Containment facility (BMC), and benchmarked with the Ansys CFX5.7 results. In the selected test, HYJET Jx7, helium was released into the containment at a speed of 42 m/s over a time of 200 s. The SST turbulence model was applied to model helium release and dispersion with both codes. The overall behaviour is captured adequately. However, there are still some noticeable differences between the CFX and OpenFOAM solutions. The study confirms the potential of using open source codes like OpenFOAM in some nuclear applications. Nevertheless further investigations and improvements are needed

The calibration facilities of gamma-ray spectrometer oil logging system

International Nuclear Information System (INIS)

Zhao Yunlong; Liu Yuzhang; Duan Wenxian

1993-08-01

The construction technology for the calibration facilities of gamma-ray spectrometer oil logging system is introduced. It is referenced to the experience from similar calibration facilities at home and abroad. Facilities consist of 9 models. The effective diameter of each model is 1.5 m and the height is 6 m. Each borehole has U ore zone, Th ore zone, K ore zone, high mixed zone, high mixed thin zone, low mixed zone and barren zone. There are 45 zones in total. Each element model has 6 in, 8.5 in and 12 in of different diameters. The preventing radon migration and complete sealing technology are used for each zone to prevent radon from escaping. The density of models, homogeneity and moisture of radio elements have been measured that gives a complete data for calibration adjusting of the instrument. The sizes of facilities and the concentration of radioactivity are reasonable designed and conformed to the recommendation of IAEA. Parameters are consistent with the parameters of calibration facilities built by Houston University in America. The emanation coefficient of the facilities is lees than 1%. The dry density of filling is 2.12 g/cm 3 and the relative standard deviation is +- 1.9%

Estimating the Value of Oil Capital in a Small Open Economy: the Venezuela's Example

OpenAIRE

Aniyar, Sara

2003-01-01

The paper focuses in the calculation of the oil capital value in a small open economy depending on oil rents. The Venezuelan case is used as an example. In valuing the oil capital, two issues are recalled and discussed: how should the exploration costs and the capital gains be treated? It is shown that the estimations vary significantly depending on which set of assumptions are made about the way to account for them and the assumptions made about how the economy functions. It is argued that d...

Feedback versus open-loop leader/fringe models of the oil supply market

International Nuclear Information System (INIS)

Pelot, R.P.; Fuller, J.D.

1991-01-01

A multiperiod feedback Stackelberg model of exhaustible resources is presented. The results of the feedback model are compared with those from a corresponding open-loop formulation to determine whether the solution to the latter, and much simpler, model produces the same or similar outcomes. An analysis of the world oil market with OPEC as leader dictating the price to a competitive fringe comprised of the remaining oil suppliers demonstrates the features of the model. It permits variable length periods and cumulative extraction cost functions

North Slope, Alaska ESI: FACILITY (Facility Points)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains data for oil field facilities for the North Slope of Alaska. Vector points in this data set represent oil field facility locations. This data...

Ecological aspects in construction of West Siberian oil field surface facilities

International Nuclear Information System (INIS)

Scvortzov, I.D.; Crushin, P.N.

1991-01-01

The exploitation of arctic regions, where permanently frozen grounds are widespread, leads to problems concerning the climate and the geo-cryological environment. One of the most urgent tasks is to minimize effects on the environment, otherwise irreversible, catastrophic processes, the deterioration of permafrost into swamps, fouling subsoil waters and rivers, ground surface pollution with petroleum products, and destruction of fish and birds, may occur. The measures aimed at providing the environmental ecological equilibrium during the exploitation of the northern oil deposits of West Siberia are described in this paper. These measures are worked out during the design stage. Then appropriate engineering decisions and product procedures are chosen, where much prominence is given to reliability of the oil and gas field facilities. The paper includes information about developing measures for the preventive systematic maintenance of the oil pipelines, maintenance schedule, prediction of accidents and certain procedures for their rectification

Responding to oil spills in the open ocean environment

International Nuclear Information System (INIS)

Wood, A.E.

1994-01-01

The primary objectives in responding to any oil spill is to control the source of the spill, then, contain, collect, and recover the spilled product. Accomplishing those objectives is an immense challenge. It becomes much more difficult when attempted in the open ocean environment due to the more complex logistical and communications problems one encounters when operating miles from the nearest land. Often times, too, the response must be coordinated with either a salvage operation, a fire-fighting operation, a well control operation or a combination of any of these. There have been volumes of papers comparing the relative merits of mechanical recovery, in-situ burning, dispersant application, and bioremediation in responding to open ocean spills. Although each approach deserves special consideration in different circumstances, this presentation focuses on mechanical methods; the specialized equipment and operational tactics that are best utilized in responding to a major spill in the open ocean. This paper is divided into two sections. The first section, Equipment Used in Open Ocean Spills, addresses in general terms, the special equipment required in an offshore response operation. The second section, entitled Operational Tactics Used In Open Ocean Spills offers an overview of the tactics employed to achieve the general objectives of containment, collection, recovery, and temporary storage

Future neutrino oscillation facilities: physics priorities and open issues

International Nuclear Information System (INIS)

Blondel, Alain

2006-01-01

The recent discovery that neutrinos have masses opens a wide new field of experimentation. Accelerator-made neutrinos are essential in this program. Ideas for future facilities include Superbeam, Beta-beam, or Neutrino Factory, each associated with one or several options for detector systems. We now begin a 'scoping study' aimed at determining a set of key R and D projects enabling the community to propose an ambitious accelerator neutrino program at the turn of this decade. As an introduction to this study, a set of physics priorities, a summary of the perceived virtues and shortcomings of the various options, and a number of open questions are presented

Top-down Estimates of Greenhouse Gas Intensities and Emissions for Individual Oil Sands Facilities in Alberta Canada

Science.gov (United States)

Liggio, J.; Li, S. M.; Staebler, R. M.; Hayden, K. L.; Mittermeier, R. L.; McLaren, R.; Baray, S.; Darlington, A.; Worthy, D.; O'Brien, J.

2017-12-01

The oil sands (OS) region of Alberta contributes approximately 10% to Canada's overall anthropogenic greenhouse gas (GHG) emissions. Such emissions have traditionally been estimated through "bottom-up" methods which seek to account for all individual sources of GHGs within a given facility. However, it is recognized that bottom-up approaches for complex industrial facilities can be subject to uncertainties associated with incomplete or inaccurate emission factor and/or activity data. In order to quantify air pollutant emissions from oil sands activities an aircraft-based measurement campaign was performed in the summer of 2013. The aircraft measurements could also be used to quantify GHG emissions for comparison to the bottom up emissions estimates. Utilizing specific flight patterns, together with an emissions estimation algorithm and measurements of CO2 and methane, a "top-down" estimate of GHG intensities for several large surface mining operations was obtained. The results demonstrate that there is a wide variation in emissions intensities (≈80 - 220 kg CO2/barrel oil) across OS facilities, which in some cases agree with calculated intensities, and in other cases are larger than that estimated using industry reported GHG emission and oil production data. When translated to annual GHG emissions, the "top-down" approach results in a CO2 emission of approximately 41 Mega Tonnes (MT) CO2/year for the 4 OS facilities investigated, in contrast to the ≈26 MT CO2/year reported by industry. The results presented here highlight the importance of using "top-down" approaches as a complimentary method in evaluating GHG emissions from large industrial sources.

Operational Experience of an Open-Access, Subscription-Based Mass Spectrometry and Proteomics Facility

Science.gov (United States)

Williamson, Nicholas A.

2018-03-01

This paper discusses the successful adoption of a subscription-based, open-access model of service delivery for a mass spectrometry and proteomics facility. In 2009, the Mass Spectrometry and Proteomics Facility at the University of Melbourne (Australia) moved away from the standard fee for service model of service provision. Instead, the facility adopted a subscription- or membership-based, open-access model of service delivery. For a low fixed yearly cost, users could directly operate the instrumentation but, more importantly, there were no limits on usage other than the necessity to share available instrument time with all other users. All necessary training from platform staff and many of the base reagents were also provided as part of the membership cost. These changes proved to be very successful in terms of financial outcomes for the facility, instrument access and usage, and overall research output. This article describes the systems put in place as well as the overall successes and challenges associated with the operation of a mass spectrometry/proteomics core in this manner. [Figure not available: see fulltext.

Opening of Offshore Oil Business in Mexico and Associated Framework to Cope with Potential Maritime Security Threats

Directory of Open Access Journals (Sweden)

Adriana Ávila-Zúáiga-Nordfjeld

2018-03-01

Full Text Available After 75 years of State oil monopoly, Mexico performed the first business oil round in 2015 involving the private sector. This auction-round offered 14 oil exploration fields located on the continental shelf to private companies. The development and exploitation of these hydrocarbon fields faces significant challenges regarding security. The economic loss for theft of hydrocarbons through illegal connections to pipelines is estimated to 973 million, 125 thousand U.S. dollar, only for the year of 2014. While productive research has been made, it has mainly focused on transportation systems and basically, pipelines. The development and establishment of policies prioritizing maritime security and protection of critical offshore infrastructure against theft of hydrocarbons, drugs organizations and terror attacks needs to be included in the national agenda to improve maritime security and mitigate potential security threats at sea, including damage to the marine environment. This could increase the trust of investors and stakeholders and would contribute to the faster development of new exploration and production fields. While the International Ship and Port Facility Security Code (ISPS Code is the cornerstone for the construction of the port?s security program and establishes the requirements of the Port Facility Security Plan (PFSP, including oil port facilities, it has not been fully implemented in several important Mexican ports. It is concluded that some important ports lack many of the core security processes, procedures and controls that should be included in any PFSP. This article briefly reviews the situation of the oil industry from a security perspective and discusses key elements of maritime security; addressing the necessity of the inclusion of maritime security and protection of critical oil infrastructure offshore in the national agenda that would provide for future research directions in the maritime security domain and contribute to

75 FR 36773 - Pipeline Safety: Updating Facility Response Plans in Light of the Deepwater Horizon Oil Spill

Science.gov (United States)

2010-06-28

... have been, or are subsequently relocated to the Gulf to respond to the Deepwater Horizon event should.... PHMSA-2010-0175] Pipeline Safety: Updating Facility Response Plans in Light of the Deepwater Horizon Oil... 194. In light of the Deepwater Horizon oil spill in the Gulf of Mexico, which has resulted in the...

Oil spill response planning, training and facilities for wildlife in Prince William Sound, Alaska

International Nuclear Information System (INIS)

Hillman, S.O.

1996-01-01

The special provisions of the SERVS System of the Alyeska Pipeline Service Company concerning the treatment of wildlife in the event of an oil spill, were described. The Company is prepared to mobilize a rapid response for protection and treatment of wildlife in the event of an oil spill anywhere along the trans-Alaska pipeline or in Prince William Sound. Equipment for hazing, capture, and treatment is pre-assembled and staged at facilities at the Valdez Marine Terminal. Veterinarians and wildlife treatment specialists are under contract for treating oiled birds. This complex of wildlife response capabilities meets or exceeds the guidelines and response planning standards set by wildlife agencies. 7 refs., 6 figs

OPEN AIR DEMOLITION OF FACILITIES HIGHLY CONTAMINATED WITH PLUTONIUM

International Nuclear Information System (INIS)

LLOYD, E.R.

2007-01-01

The demolition of highly contaminated plutonium buildings usually is a long and expensive process that involves decontaminating the building to near free- release standards and then using conventional methods to remove the structure. It doesn't, however, have to be that way. Fluor has torn down buildings highly contaminated with plutonium without excessive decontamination. By removing the select source term and fixing the remaining contamination on the walls, ceilings, floors, and equipment surfaces; open-air demolition is not only feasible, but it can be done cheaper, better (safer), and faster. Open-air demolition techniques were used to demolish two highly contaminated buildings to slab-on-grade. These facilities on the Department of Energy's Hanford Site were located in, or very near, compounds of operating nuclear facilities that housed hundreds of people working on a daily basis. To keep the facilities operating and the personnel safe, the projects had to be creative in demolishing the structures. Several key techniques were used to control contamination and keep it within the confines of the demolition area: spraying fixatives before demolition; applying fixative and misting with a fine spray of water as the buildings were being taken down; and demolishing the buildings in a controlled and methodical manner. In addition, detailed air-dispersion modeling was done to establish necessary building and meteorological conditions and to confirm the adequacy of the proposed methods. Both demolition projects were accomplished without any spread of contamination outside the modest buffer areas established for contamination control. Furthermore, personnel exposure to radiological and physical hazards was significantly reduced by using heavy equipment rather than ''hands on'' techniques

Mitigating oil spills in the water column

International Nuclear Information System (INIS)

Barry, Edward; Libera, Joseph A.; Mane, Anil University; Avila, Jason R.; DeVitis, David

2017-01-01

The scale and scope of uncontrolled oil spills can be devastating. Diverse marine environments and fragile ecologies are some of the most susceptible to the many ill effects, while the economic costs can be crippling. A notoriously difficult challenge with no known technological solution is the successful removal of oil dispersed in the water column. Here, we address this problem through cheap and reusable oil sorbents based on the chemical modification of polymer foams. Interfacial chemistry was optimized and subsequently tested in a simulated marine environment at the National Oil Spill Response Research & Renewable Energy Test Facility, Ohmsett. We find favorable performance for surface oil mitigation and, for the first time, demonstrate the advanced sorbent's efficiency and efficacy at pilot scale in extraction of crude oil and refined petroleum products dispersed in the water column. As a result, this is a potentially disruptive technology, opening a new field of environmental science focused on sub-surface pollutant sequestration.

Environmental implications of offshore oil and gas development in Australia. Part 5; Coastal facilities

International Nuclear Information System (INIS)

Black, K.P.; Brand, G.W.; Hammond, L.S.; Mourtikas, S.; Noyes-Fitzsimmons, R.L.; Smith, J.M.; Gwyther, D.; Richardson, B.J.

1994-01-01

It is emphasised that coastal facilities pertaining to petroleum exploration and production activities are of greater concern for potential deleterious environmental consequences than the offshore facilities. This is primarily because rates of dispersion and dilution of toxic wastes are generally lower in shallow coastal waters which are often subject to complex bathymetry, and more constricted water flows. The review found that the main processes (apart from oil spills) identified as having greatest potential environmental effect were: coastal discharges of produced water; sedimentation caused by dredging; spoil dumping; and pipe-laying activities. The review examines a wide range of marine environmental issues arising from the use of coastal-servicing facilities, including: practices and discharges during regular operation of coastal facilities; nature and extent of any environmental impact on the surrounding environment; and any deleterious effects stemming from these facilities. 194 refs., 13 tabs., 36 figs

Characterization of methane emissions from five cold heavy oil production with sands (CHOPS) facilities.

Science.gov (United States)

Roscioli, Joseph R; Herndon, Scott C; Yacovitch, Tara I; Knighton, W Berk; Zavala-Araiza, Daniel; Johnson, Matthew R; Tyner, David R

2018-03-07

Cold heavy oil production with sands (CHOPS) is a common oil extraction method in the Canadian provinces of Alberta and Saskatchewan that can result in significant methane emissions due to annular venting. Little is known about the magnitude of these emissions, nor their contributions to the regional methane budget. Here the authors present the results of field measurements of methane emissions from CHOPS wells and compare them with self-reported venting rates. The tracer ratio method was used not only to analyze total site emissions but at one site it was also used to locate primary emission sources and quantify their contributions to the facility-wide emission rate, revealing the annular vent to be a dominant source. Emissions measured from five different CHOPS sites in Alberta showed large discrepancies between the measured and reported rates, with emissions being mainly underreported. These methane emission rates are placed in the context of current reporting procedures and the role that gas-oil ratio (GOR) measurements play in vented volume estimates. In addition to methane, emissions of higher hydrocarbons were also measured; a chemical "fingerprint" associated with CHOPS wells in this region reveals very low emission ratios of ethane, propane, and aromatics versus methane. The results of this study may inform future studies of CHOPS sites and aid in developing policy to mitigate regional methane emissions. Methane measurements from cold heavy oil production with sand (CHOPS) sites identify annular venting to be a potentially major source of emissions at these facilities. The measured emission rates are generally larger than reported by operators, with uncertainty in the gas-oil ratio (GOR) possibly playing a large role in this discrepancy. These results have potential policy implications for reducing methane emissions in Alberta in order to achieve the Canadian government's goal of reducing methane emissions by 40-45% below 2012 levels within 8 yr.

Foreign oil companies weathering Peru's political crisis

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that foreign oil companies are weathering Peru's political crisis, and the outlook for increased foreign participation in Peru's petroleum sector remains promising. There has been improvement in the political turmoil and soured international relations that followed President Alberto Fujimori's Apr. 5 suspension of Peru's Congress, charging political corruption and attempts to block his fiscal reforms. But there are fresh concerns over an increase in terrorism aimed at oil industry facilities by antigovernment guerrilla groups in Peru. Meanwhile, state-owned oil company Petroleos del Peru (Petroperu) continues efforts to sell assets as part of Fujimori's mandated privatization program. And foreign companies continue to grapple with uncertainty and bureaucratic red tape in chasing investment opportunities in Peru's beleaguered but opening petroleum sector

Topical Coconut Oil in Very Preterm Infants: An Open-Label Randomised Controlled Trial.

Science.gov (United States)

Strunk, Tobias; Pupala, Sameer; Hibbert, Julie; Doherty, Dorota; Patole, Sanjay

2018-01-01

The immature fragile skin of preterm infants represents an inadequate protective barrier. The emollient and anti-infective properties of coconut oil make it a potentially beneficial topical agent for this population. Our aim was to evaluate feasibility, safety, and the effects of topical coconut oil on skin condition in very preterm infants. An open-label randomised controlled trial in preterm infants coconut oil (5 mL/kg) twice daily for 21 days, starting within 24 h of birth. The neonatal skin condition was the primary outcome, and was assessed using the Neonatal Skin Condition Score (NSCS) on days 1, 7, 14, and 21. The number of coconut oil applications was recorded to assess clinical feasibility and all enrolled infants were monitored for adverse effects of topical coconut application, such as skin irritation. A total of 72 infants born coconut oil was feasible and without adverse effects. The NSCS was maintained in the coconut oil group throughout the intervention period, but deteriorated from a median (IQR) of 3 (3-4) on day 1 to 4 (4-4) on day 21 in the control group (p = 0.01). There were no differences in common neonatal outcomes, including sepsis, necrotising enterocolitis, retinopathy of prematurity, chronic lung disease, and mortality. Topical coconut oil maintained a better skin condition in very preterm infants without adverse effects. This simple, safe, and affordable intervention warrants further investigation. © 2017 S. Karger AG, Basel.

33 CFR 154.1216 - Facility classification.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Facility classification. 154.1216... Vegetable Oils Facilities § 154.1216 Facility classification. (a) The Coast Guard classifies facilities that... classification of a facility that handles, stores, or transports animal fats or vegetable oils. The COTP may...

Spilled oil and infaunal activity - Modification of burrowing behavior and redistribution of oil

Science.gov (United States)

Clifton, H.E.; Kvenvolden, K.A.; Rapp, J.B.

1984-01-01

A series of experiments in Willapa Bay, Washington, indicates the degree to which the presence of spilled oil modifies the burrowing behavior of infauna and the extent to which the animals redistribute oil into intertidal sediment. Small amounts of North Slope crude oil introduced at low tide directly into burrow openings (mostly made by the crustacean Callianassa) resulted in a limited and temporary reduction in the number of burrow openings. In contrast, a layer of oil-saturated sand 1 cm thick buried about 5 cm below the sediment surface sharply reduced the number of burrow openings. After a year, the few new burrows penetrated only the margins of the experimental plot, and bioturbation below the buried oil-saturated sand layer declined dramatically. The experiments suggest that small amounts of oil temporarily stranded by tides in themselves have no long-range effect on burrowing behavior. The fauna, however, are capable of introducing measurable amounts of oil into the subsurface, where it is retained long after the rest of the stranded oil had washed away. A buried layer of oil-saturated sand greatly reduces infaunal activity; the oil presents an effective barrier that can persist for years. The oil incorporated into the sediment from burrow openings showed evidence of degradation after 7 months. In contrast the layer of buried oil remained essentially undergraded after a period of two years, even though oil in lower concentrations above the layer was degraded after a period of one year. This variation in degree of degradation of the buried oil, as well as the heterogeneity of oil distribution wherever the oil has been incorporated from the surface, emphasises the importance of careful sampling in any attempt to locate or monitor the presence of spilled oil in the substrate.In a series of experiments in Willapa Bay, Washington, small amounts of North Slope crude oil introduced at low tide directly into burrow openings resulted in a limited and temporary

Facile Preparation of Nanostructured, Superhydrophobic Filter Paper for Efficient Water/Oil Separation.

Directory of Open Access Journals (Sweden)

Jianhua Wang

Full Text Available In this paper, we present a facile and cost-effective method to obtain superhydrophobic filter paper and demonstrate its application for efficient water/oil separation. By coupling structurally distinct organosilane precursors (e.g., octadecyltrichlorosilane and methyltrichlorosilane to paper fibers under controlled reaction conditions, we have formulated a simple, inexpensive, and efficient protocol to achieve a desirable superhydrophobic and superoleophilic surface on conventional filter paper. The silanized superhydrophobic filter paper showed nanostructured morphology and demonstrated great separation efficiency (up to 99.4% for water/oil mixtures. The modified filter paper is stable in both aqueous solutions and organic solvents, and can be reused multiple times. The present study shows that our newly developed binary silanization is a promising method of modifying cellulose-based materials for practical applications, in particular the treatment of industrial waste water and ecosystem recovery.

The CT Scanner Facility at Stellenbosch University: An open access X-ray computed tomography laboratory

Science.gov (United States)

du Plessis, Anton; le Roux, Stephan Gerhard; Guelpa, Anina

2016-10-01

The Stellenbosch University CT Scanner Facility is an open access laboratory providing non-destructive X-ray computed tomography (CT) and a high performance image analysis services as part of the Central Analytical Facilities (CAF) of the university. Based in Stellenbosch, South Africa, this facility offers open access to the general user community, including local researchers, companies and also remote users (both local and international, via sample shipment and data transfer). The laboratory hosts two CT instruments, i.e. a micro-CT system, as well as a nano-CT system. A workstation-based Image Analysis Centre is equipped with numerous computers with data analysis software packages, which are to the disposal of the facility users, along with expert supervision, if required. All research disciplines are accommodated at the X-ray CT laboratory, provided that non-destructive analysis will be beneficial. During its first four years, the facility has accommodated more than 400 unique users (33 in 2012; 86 in 2013; 154 in 2014; 140 in 2015; 75 in first half of 2016), with diverse industrial and research applications using X-ray CT as means. This paper summarises the existence of the laboratory's first four years by way of selected examples, both from published and unpublished projects. In the process a detailed description of the capabilities and facilities available to users is presented.

The CT Scanner Facility at Stellenbosch University: An open access X-ray computed tomography laboratory

Energy Technology Data Exchange (ETDEWEB)

Plessis, Anton du, E-mail: anton2@sun.ac.za [CT Scanner Facility, Central Analytical Facilities, Stellenbosch University, Stellenbosch (South Africa); Physics Department, Stellenbosch University, Stellenbosch (South Africa); Roux, Stephan Gerhard le, E-mail: lerouxsg@sun.ac.za [CT Scanner Facility, Central Analytical Facilities, Stellenbosch University, Stellenbosch (South Africa); Guelpa, Anina, E-mail: aninag@sun.ac.za [CT Scanner Facility, Central Analytical Facilities, Stellenbosch University, Stellenbosch (South Africa)

2016-10-01

The Stellenbosch University CT Scanner Facility is an open access laboratory providing non-destructive X-ray computed tomography (CT) and a high performance image analysis services as part of the Central Analytical Facilities (CAF) of the university. Based in Stellenbosch, South Africa, this facility offers open access to the general user community, including local researchers, companies and also remote users (both local and international, via sample shipment and data transfer). The laboratory hosts two CT instruments, i.e. a micro-CT system, as well as a nano-CT system. A workstation-based Image Analysis Centre is equipped with numerous computers with data analysis software packages, which are to the disposal of the facility users, along with expert supervision, if required. All research disciplines are accommodated at the X-ray CT laboratory, provided that non-destructive analysis will be beneficial. During its first four years, the facility has accommodated more than 400 unique users (33 in 2012; 86 in 2013; 154 in 2014; 140 in 2015; 75 in first half of 2016), with diverse industrial and research applications using X-ray CT as means. This paper summarises the existence of the laboratory’s first four years by way of selected examples, both from published and unpublished projects. In the process a detailed description of the capabilities and facilities available to users is presented.

EFFECT OF INJECTOR OPENING PRESSURE ON PERFORMANCE AND EMISSION OF LPG - METHYL ESTER OF MAHUA OIL DUAL FUEL ENGINE

Directory of Open Access Journals (Sweden)

N. Kapilan

2017-11-01

Full Text Available One of variables, which affect the performance and emission of dual fuel engine is injection pressure. Hence in the present work, effect of Injector opening pressure on the performance of the engine was studied.  A four stroke single cylinder engine was modified to work in dual fuel mode. Three injector opening pressures (180 bar, 200 bar and 220 bar were considered for the present work. Methyl ester of mahua oil was used as pilot fuel and LPG was used as primary fuel.    From the test results, it was observed that the injector opening pressure of 200 bar results in higher brake thermal efficiency. The higher injector opening pressure results in better atomization and peneatration of methyl ester of mahua oil. The exhaust emissions such as Smoke, unburnt hydro carbon and carbon monoxide of 200 bar is lower than other pressures.

Implementation of Grid Tier 2 and Tier 3 facilities on a Distributed OpenStack Cloud

Science.gov (United States)

Limosani, Antonio; Boland, Lucien; Coddington, Paul; Crosby, Sean; Huang, Joanna; Sevior, Martin; Wilson, Ross; Zhang, Shunde

2014-06-01

The Australian Government is making a AUD 100 million investment in Compute and Storage for the academic community. The Compute facilities are provided in the form of 30,000 CPU cores located at 8 nodes around Australia in a distributed virtualized Infrastructure as a Service facility based on OpenStack. The storage will eventually consist of over 100 petabytes located at 6 nodes. All will be linked via a 100 Gb/s network. This proceeding describes the development of a fully connected WLCG Tier-2 grid site as well as a general purpose Tier-3 computing cluster based on this architecture. The facility employs an extension to Torque to enable dynamic allocations of virtual machine instances. A base Scientific Linux virtual machine (VM) image is deployed in the OpenStack cloud and automatically configured as required using Puppet. Custom scripts are used to launch multiple VMs, integrate them into the dynamic Torque cluster and to mount remote file systems. We report on our experience in developing this nation-wide ATLAS and Belle II Tier 2 and Tier 3 computing infrastructure using the national Research Cloud and storage facilities.

Implementation of Grid Tier 2 and Tier 3 facilities on a Distributed OpenStack Cloud

International Nuclear Information System (INIS)

Limosani, Antonio; Boland, Lucien; Crosby, Sean; Huang, Joanna; Sevior, Martin; Coddington, Paul; Zhang, Shunde; Wilson, Ross

2014-01-01

The Australian Government is making a $AUD 100 million investment in Compute and Storage for the academic community. The Compute facilities are provided in the form of 30,000 CPU cores located at 8 nodes around Australia in a distributed virtualized Infrastructure as a Service facility based on OpenStack. The storage will eventually consist of over 100 petabytes located at 6 nodes. All will be linked via a 100 Gb/s network. This proceeding describes the development of a fully connected WLCG Tier-2 grid site as well as a general purpose Tier-3 computing cluster based on this architecture. The facility employs an extension to Torque to enable dynamic allocations of virtual machine instances. A base Scientific Linux virtual machine (VM) image is deployed in the OpenStack cloud and automatically configured as required using Puppet. Custom scripts are used to launch multiple VMs, integrate them into the dynamic Torque cluster and to mount remote file systems. We report on our experience in developing this nation-wide ATLAS and Belle II Tier 2 and Tier 3 computing infrastructure using the national Research Cloud and storage facilities.

Comparative techno-economic analysis of biohydrogen production via bio-oil gasification and bio-oil reforming

International Nuclear Information System (INIS)

Zhang, Yanan; Brown, Tristan R.; Hu, Guiping; Brown, Robert C.

2013-01-01

This paper evaluates the economic feasibility of biohydrogen production via two bio-oil processing pathways: bio-oil gasification and bio-oil reforming. Both pathways employ fast pyrolysis to produce bio-oil from biomass stock. The two pathways are modeled using Aspen Plus ® for a 2000 t d −1 facility. Equipment sizing and cost calculations are based on Aspen Economic Evaluation® software. Biohydrogen production capacity at the facility is 147 t d −1 for the bio-oil gasification pathway and 160 t d −1 for the bio-oil reforming pathway. The biomass-to-fuel energy efficiencies are 47% and 84% for the bio-oil gasification and bio-oil reforming pathways, respectively. Total capital investment (TCI) is 435 million dollars for the bio-oil gasification pathway and is 333 million dollars for the bio-oil reforming pathway. Internal rates of return (IRR) are 8.4% and 18.6% for facilities employing the bio-oil gasification and bio-oil reforming pathways, respectively. Sensitivity analysis demonstrates that biohydrogen price, biohydrogen yield, fixed capital investment (FCI), bio-oil yield, and biomass cost have the greatest impacts on facility IRR. Monte-Carlo analysis shows that bio-oil reforming is more economically attractive than bio-oil gasification for biohydrogen production. -- Highlights: ► Biohydrogen production via bio-oil reforming has higher energy efficiency compared to gasification. ► Hydrogen price, fixed capital cost, and feedstock cost most strongly affect IRR. ► Lower risk investment is biohydrogen production via bio-oil reforming

Environmental risk analysis of oil handling facilities in port areas. Application to Tarragona harbor (NE Spain).

Science.gov (United States)

Valdor, Paloma F; Gómez, Aina G; Puente, Araceli

2015-01-15

Diffuse pollution from oil spills is a widespread problem in port areas (as a result of fuel supply, navigation and loading/unloading activities). This article presents a method to assess the environmental risk of oil handling facilities in port areas. The method is based on (i) identification of environmental hazards, (ii) characterization of meteorological and oceanographic conditions, (iii) characterization of environmental risk scenarios, and (iv) assessment of environmental risk. The procedure has been tested by application to the Tarragona harbor. The results show that the method is capable of representing (i) specific local pollution cases (i.e., discriminating between products and quantities released by a discharge source), (ii) oceanographic and meteorological conditions (selecting a representative subset data), and (iii) potentially affected areas in probabilistic terms. Accordingly, it can inform the design of monitoring plans to study and control the environmental impact of these facilities, as well as the design of contingency plans. Copyright © 2014 Elsevier Ltd. All rights reserved.

Design investigation of the HTR for the opening of very heavy oil deposits

International Nuclear Information System (INIS)

Gao, Z.

1985-02-01

In the north-east of China there are rich deposits of very heavy oil, which are to be found in a depth of 1500-1700 m. For opening an interaction of 370-390 0 Celsius steam is necessary. The HTR is well suited to produce the steam. A nuclear heat source of 1000 MWsub(th) makes possible the production of 1.5 million tons oil per year. This is a 30-40 per cent higher production of oil compared to the oil-fired steam production. Two concepts of smaller pebble bed reactors are suited as heat sources: the HTR-MEDUL-334 with a thermal power of the 334 MW and fuelled in the multiple run-through scheme and the HTR-OTTO-200 with 200 MW and once-through fuelling. Three or five reactors can be combined in the modular way to provide the power of 1000 MW. For both reactors the design, the neutron-physical and thermohydraulic behaviour are followed in the computer simulation. A central zone of the pebble bed reactor is fuelled with elements of strongly reduced fissile content. Due to the reduced power density the maximum fuel temperature appearing in extreme accidents is limited and accordingly the release of the fission products is avoided. (orig.) [de

Cuba's opening to oil in the Gulf of Mexico: between Mexico's opposition to change and the United States' Blockade

International Nuclear Information System (INIS)

De la Vega Navarro, A.

2007-01-01

The future of oil for Cuba, Mexico and the United States, which have common maritime borders, lies in the deep waters of the Gulf of Mexico. Cuba faces an energy transition where that source of energy still lays a role, considering the economic and technological structures from the past. Among others, it has opened its territory to international companies, providing them with access to carbon hydride resources in an area of strategic importance, in the midst of a world energy situation where each barrel of oil counts. In addition to economic and technological factors, the Cuban oil opening is explained by the critical situation generated after the termination of the relationship that the country had maintained for several decades with the USSR. The out-come and credibility of such opening should be put into perspective with its ability to build an institutional and regulatory environment likely to attract foreign investments in high risk exploration and production activities. At the same time, Cuba has managed to complete the internal effort conducted with the help of international companies, by engaging in a special relationship with Venezuela, as part of new regional integration programmes and energy cooperation initiated by that country. (author)

A facile way to prepare CuS-oil nanofluids with enhanced thermal conductivity and appropriate viscosity

Energy Technology Data Exchange (ETDEWEB)

Qin, Ji-Hua; Liu, Zhao-Qing; Li, Nan, E-mail: nanli@gzhu.edu.cn; Chen, Yi-Bo; Wang, Dong-Yao [Guangzhou University, School of Chemistry and Chemical Engineering/Guangzhou Key Laboratory for Environmentally Functional Materials and Technology (China)

2017-02-15

The nanofluid as a pivotal role in heat transfer system has attracted more and more attention. Herein, the stearic acid-modified CuS (SA-CuS) nanoparticles with a uniform diameter of 60 nm were synthesized successfully by a facile two-phase approach. Accordingly, the CuS-oil nanofluids, with SA-CuS concentrations ranging from 0.01 to 0.04 vol%, were prepared by a one-step method in the heat transfer oil. These CuS-oil nanofluids exhibit good stability and considerable enhanced thermal conductivity. The improvement is even up to 20.5% with a volume fraction of 0.04 vol% at 30 °C. Furthermore, the effect of volume fraction and temperature on the viscosity of the nanofluids was also systematically investigated.

Alberta's new oil boom

International Nuclear Information System (INIS)

Nikiforuk, A.

1997-01-01

A massive expansion of Canada's oil sands and the oil-mining business is underway. The prediction is that within five years there will be at least three, possibly six, huge new open pit mines north of Fort McMurray, Alberta. It was suggested that within 20 years, possibly half of Canada's oil supply will come from the oil sands industry which has already attracted $10 billion worth of developments. Unlike conventional crude, the oil sands contain bitumen, water, clay, minerals and lots of sands. Shallow deposits are mined like coal. Deeper formations make use of in-situ thermal recovery techniques. Extraction costs are presently at $15 per barrel, aiming for $12 by 1999. Return on investment is in double digits. Estimates of reserves in the Athabasca, Cold Lake, Peace River and Wabasca deposits go as high as 1.7 trillion barrels, or about twice as much as Saudi Arabia's conventional crude reserves. Syncrude has built a $5 billion production facility and two pipelines have already been proposed to transport the oil sands crude to midwestern US refineries. US refineries prize synthetic crude as excellent mixing stock. The major problem with oil sands is that unlike conventional oil, these reserves require an enormous amount of energy to exploit, which in turn means lots of foul air and greenhouse gases. There are many environmental unknowns, and without a clear management framework in sight the addition of two or three Syncrude-size operations has the potential to create a real and significant acid rain problem in the Western Canada Basin

Magnetohydrodynamics (MHD) Engineering Test Facility (ETF) 200 MWe power plant Conceptual Design Engineering Report (CDER)

Science.gov (United States)

1981-01-01

The reference conceptual design of the magnetohydrodynamic (MHD) Engineering Test Facility (ETF), a prototype 200 MWe coal-fired electric generating plant designed to demonstrate the commercial feasibility of open cycle MHD, is summarized. Main elements of the design, systems, and plant facilities are illustrated. System design descriptions are included for closed cycle cooling water, industrial gas systems, fuel oil, boiler flue gas, coal management, seed management, slag management, plant industrial waste, fire service water, oxidant supply, MHD power ventilating

Suspension, abandonment, decontamination, and surface land reclamation of upstream oil and gas facilities : informational letter IL 98-2

International Nuclear Information System (INIS)

1998-01-01

This release of the Alberta Energy and Utilities Board (EUB) is intended to clarify the jurisdictional roles of Alberta Environmental Protection (AEP) and the EUB with regard to their respective responsibilities for the regulation of the suspension, abandonment, decontamination and surface land reclamation of active and inactive upstream oil and gas facilities. The EUB, AEP and industrial operators all have separate roles and responsibilities when active and inactive upstream facilities are suspended or reclaimed. In the future, industry operators will have more interaction with the AEP during the decontamination of a site, while the EUB will concentrate on pollution prevention and abandonment of non-economic facilities. All oilfield waste generated from suspension, abandonment, decontamination, and surface land reclamation of an active or inactive upstream oil and gas facility will fall under the jurisdiction of the EUB. Contaminated soils, sludges, and waters that are physically removed as a result of decontamination activities are considered to be oilfield wastes. The regulatory responsibility between the AEP and the EUB remains unchanged for the reclamation process of on-lease and off-lease spills, releases or pipeline breaks. Industry operators are no longer allowed to discharge any produced liquid to earthen pits or ponds and are encouraged to reclaim existing ones. 3 figs

Reclamation and closure of an oil sands tailings facility

Energy Technology Data Exchange (ETDEWEB)

Sobkowicz, J. [Thurber Engineering Ltd., Calgary, AB (Canada); Morgenstern, N. [Alberta Univ., Edmonton, AB (Canada)

2010-07-01

This PowerPoint presentation discussed methods of ensuring the successful reclamation of oil sands tailings facilities. Tailings should be reclaimed as mining proceeds in order to avoid an excessive accumulation of fluid fine tailings (FFT). The volume of mature fine tailings (MFT) in ponds should be limited in order to ensure effective tailings management. The reclaimed landforms should have good geotechnical stability and be comprised of self-sustaining native vegetation. Strength is needed to allow for timely capping and initial reclamation, and stiffness is required to minimize future settlement and to allow for the construction of a closure landscape. Reclamation strategies were presented for fines-dominated tailings; sand-depleted tailings; and sand-dominated tailings. Energy Resources Conservation Board (ERCB) criteria for tailings reclamation were discussed, and various monitoring and performance assessment strategies were presented. tabs., figs.

Radon gas in oil and natural gas production facilities

International Nuclear Information System (INIS)

Chandler, W.P.

1994-01-01

Radon gas is a naturally occurring radionuclide that can be found in some oil and natural gas production facilities, either as a contaminant in a natural gas stream or derived from Radium dissolved in formation waters. The gas itself is not normally a health hazard, but it's decay products, which can be concentrated by plate-out or deposition as a scale in process equipment, can be a health hazard for maintenance personnel. To evaluate possible health hazards, it is necessary to monitor for naturally occurring radioactive materials (NORM) in the gas stream and in the formation water. If Radon and/or Radium is found, a monitoring programme should be initiated to comply with National or State requirements. In some instances, it has been found necessary to dispose of silt and scale materials as low level radioactive waste. 8 refs

Open-source LCA tool for estimating greenhouse gas emissions from crude oil production using field characteristics.

Science.gov (United States)

El-Houjeiri, Hassan M; Brandt, Adam R; Duffy, James E

2013-06-04

Existing transportation fuel cycle emissions models are either general and calculate nonspecific values of greenhouse gas (GHG) emissions from crude oil production, or are not available for public review and auditing. We have developed the Oil Production Greenhouse Gas Emissions Estimator (OPGEE) to provide open-source, transparent, rigorous GHG assessments for use in scientific assessment, regulatory processes, and analysis of GHG mitigation options by producers. OPGEE uses petroleum engineering fundamentals to model emissions from oil and gas production operations. We introduce OPGEE and explain the methods and assumptions used in its construction. We run OPGEE on a small set of fictional oil fields and explore model sensitivity to selected input parameters. Results show that upstream emissions from petroleum production operations can vary from 3 gCO2/MJ to over 30 gCO2/MJ using realistic ranges of input parameters. Significant drivers of emissions variation are steam injection rates, water handling requirements, and rates of flaring of associated gas.

Proceedings of the oil sands and heavy oil technologies conference and exhibition

International Nuclear Information System (INIS)

2009-01-01

This conference provided a forum for oil sands industry leaders to review the current and future state of technology in this frontier environment. Presentations were delivered by key personnel involved in groundbreaking projects with a renewed focus on oil sands technology and equipment, viewed from the strategic level with case studies and reports on application technologies designed to optimize oil sands operations. The presentations addressed a wide range of issues related to the environmental impacts of oil sands processing facilities, including innovative water and wastewater solutions for heavy oil producers for bitumen mining, in-situ and upgrading facilities. New advances in sulphur treatment technologies were highlighted along with technologies designed to increase the energy efficiency and energy consumption rates of upgrader and processing facilities. Advances in carbon dioxide (CO 2 ) capture and storage systems were also discussed along with geopolitical and economic evaluations of the future of the oil sands industry. The conference featured 59 presentations, of which 48 have been catalogued separately for inclusion in this database. refs., tabs., figs

Oil and gas field code master list 1994

Energy Technology Data Exchange (ETDEWEB)

1995-01-01

This is the thirteenth annual edition of the Energy Information Administration`s (EIA) Oil and Gas Field Code Master List. It reflects data collected through October 1994 and provides standardized field name spellings and codes for all identified oil and/or gas fields in the United States. The master field name spellings and codes are to be used by respondents when filing the following Department of Energy (DOE) forms: Form EIA-23, {open_quotes}Annual Survey of Domestic Oil and Gas Reserves,{close_quotes} filed by oil and gas well operators (field codes are required from larger operators only); Forms FERC 8 and EIA-191, {open_quotes}Underground Gas Storage Report,{close_quotes} filed by natural gas producers and distributors who operate underground natural gas storage facilities. Other Federal and State government agencies, as well as industry, use the EIA Oil and Gas Field Code Master List as the standard for field identification. A machine-readable version of the Oil and Gas Field Code Master List is available from the National Technical Information Service, 5285 Port Royal Road, Springfield, Virginia 22161, (703) 487-4650. In order for the Master List to be useful, it must be accurate and remain current. To accomplish this, EIA constantly reviews and revises this list. The EIA welcomes all comments, corrections, and additions to the Master List. All such information should be given to the EIA Field Code Coordinator at (214) 953-1858. EIA gratefully acknowledges the assistance provides by numerous State organizations and trade associations in verifying the existence of fields and their official nomenclature.

Economic impacts of oil spills: Spill unit costs for tankers, pipelines, refineries, and offshore facilities

International Nuclear Information System (INIS)

1993-01-01

The impacts of oil spills -- ranging from the large, widely publicized Exxon Valdez tanker incident to smaller pipeline and refinery spills -- have been costly to both the oil industry and the public. For example, the estimated costs to Exxon of the Valdez tanker spill are on the order of $4 billion, including $2.8 billion (in 1993 dollars) for direct cleanup costs and $1.125 billion (in 1992 dollars) for settlement of damages claims caused by the spill. Application of contingent valuation costs and civil lawsuits pending in the State of Alaska could raise these costs appreciably. Even the costs of the much smaller 1991 oil spill at Texaco's refinery near Anacortes, Washington led to costs of $8 to 9 million. As a result, inexpensive waming, response and remediation technologies could lower oil spin costs, helping both the oil industry, the associated marine industries, and the environment. One means for reducing the impact and costs of oil spills is to undertake research and development on key aspects of the oil spill prevention, warming, and response and remediation systems. To target these funds to their best use, it is important to have sound data on the nature and size of spills, their likely occurrence and their unit costs. This information could then allow scarce R ampersand D dollars to be spent on areas and activities having the largest impact. This report is intended to provide the ''unit cost'' portion of this crucial information. The report examines the three key components of the US oil supply system, namely, tankers and barges; pipelines and refineries; and offshore production facilities. The specific purpose of the study was to establish the unit costs of oil spills. By manipulating this key information into a larger matrix that includes the size and frequency of occurrence of oil spills, it will be possible' to estimate the likely future impacts, costs, and sources of oil spills

Opportunities for Energy Efficiency and Open Automated Demand Response in Wastewater Treatment Facilities in California -- Phase I Report

Energy Technology Data Exchange (ETDEWEB)

Lekov, Alex; Thompson, Lisa; McKane, Aimee; Song, Katherine; Piette, Mary Ann

2009-04-01

This report summarizes the Lawrence Berkeley National Laboratory?s research to date in characterizing energy efficiency and automated demand response opportunities for wastewater treatment facilities in California. The report describes the characteristics of wastewater treatment facilities, the nature of the wastewater stream, energy use and demand, as well as details of the wastewater treatment process. It also discusses control systems and energy efficiency and automated demand response opportunities. In addition, several energy efficiency and load management case studies are provided for wastewater treatment facilities.This study shows that wastewater treatment facilities can be excellent candidates for open automated demand response and that facilities which have implemented energy efficiency measures and have centralized control systems are well-suited to shift or shed electrical loads in response to financial incentives, utility bill savings, and/or opportunities to enhance reliability of service. Control technologies installed for energy efficiency and load management purposes can often be adapted for automated demand response at little additional cost. These improved controls may prepare facilities to be more receptive to open automated demand response due to both increased confidence in the opportunities for controlling energy cost/use and access to the real-time data.

Open Innovation at the Root of Entrepreneurial Strategy: A Case from the Norwegian Oil Industry

Directory of Open Access Journals (Sweden)

Tatiana Iakovleva

2013-04-01

Full Text Available This article aims to extend the discussion about entrepreneurial strategies of small and medium-sized enterprises (SMEs by including the concept of open innovation. How can SMEs overcome the challenges of resource scarcity and harsh competition? How they can gain competitive advantage in today’s ever-changing business environment? The answer to both of these questions might be through open innovation: collaborating with researchers, customers, suppliers – even competitors – as well as research institutions and universities. A common barrier to open innovation in an SME is the perception that it will be too time consuming to gain access to a knowledge base of external knowledge providers and link to “gatekeepers” of knowledge. However, an entrepreneurial mindset might help SMEs to move toward an open-innovation approach, where more codified and transferrable knowledge are important. This article discusses the implications of an entrepreneurial focus for open-innovation activities. The usefulness of the open-innovation principles are highlighted through a case study of an Norwegian SME operating in the maritime-oil industry.

Hydrocarbon distributions in sediments of the open area of the Arabian Gulf following the 1991 Gulf War oil spill

International Nuclear Information System (INIS)

Al-Lihaibi, S.S.; Ghazi, S.J.

1997-01-01

Surface sediments collected from the open area of the Arabian Gulf were analysed for total petroleum hydrocarbons and specific aliphatic hydrocarbon components in order to provide information on the extent of oil contamination and the degree of weathering of the spilled oil following the Gulf War. The surface distribution of the petroleum hydrocarbons showed an increasing trend towards the north-east, and among the individual transects there was a pronounced increasing trend towards the north-west direction. Despite off-shore oil-related activities as well as a potential impact from the 1991 oil spill, the concentrations of petroleum hydrocarbons in the study area were relatively low. This finding may be attributed to the effectiveness of weathering processes. (author)

Software and Hardware System for Fast Processes Study When Preparing Foundation Beds of Oil and Gas Facilities

Science.gov (United States)

Gruzin, A. V.; Gruzin, V. V.; Shalay, V. V.

2018-04-01

Analysis of existing technologies for preparing foundation beds of oil and gas buildings and structures has revealed the lack of reasoned recommendations on the selection of rational technical and technological parameters of compaction. To study the nature of the dynamics of fast processes during compaction of foundation beds of oil and gas facilities, a specialized software and hardware system was developed. The method of calculating the basic technical parameters of the equipment for recording fast processes is presented, as well as the algorithm for processing the experimental data. The performed preliminary studies confirmed the accuracy of the decisions made and the calculations performed.

Sustainable Governance for the Opened Electric Vehicle Charging and Upgraded Facilities Market

Directory of Open Access Journals (Sweden)

Tian Wu

2017-11-01

Full Text Available Since the China State Grid opened the market for infrastructure construction of electric charging stations and allowed Tesla, Potevio, BAIC BJEV and other enterprises to provide their own charging stations and other infrastructure construction, the development of electric vehicles has been greatly affected. How to maintain a sustainable governance in the opened electric vehicle charging and upgraded facilities market is an important policy issues. This paper presents a monopolistic competition model for the differentiated products market and addresses several issues related to Cournot equilibrium to illustrate why the expected free market actually operates in a monopolistic competition market structure. The analytic solution of the model shows that whether the extent of firm entry is insufficient, excessive or optimum is determined by consumers’ time preference, level of production differentiation and features of cost structure, including fixed cost and marginal cost. The sensitivity analysis has been performed among the above factors and tracked some other factors which would determine the effect of the new policy issues. The main policy suggestion is that the government should optimize entry regulations and lay down the criterion of charging interface standards for charging stations to avoid the electric vehicle charging and upgraded facilities marketization process of a one-size-fits-all solution and form a monopolistic competition market.

Effect of Inhalation of Lavender Essential Oil on Vital Signs in Open Heart Surgery ICU.

Science.gov (United States)

Salamati, Armaiti; Mashouf, Soheyla; Mojab, Faraz

2017-01-01

This study evaluated the effects of inhalation of Lavender essential oil on vital signs in open heart surgery ICU. The main complaint of patients after open-heart surgery is dysrhythmia, tachycardia, and hypertension due to stress and pain. Due to the side effects of chemical drugs, such as opioids, use of non-invasive methods such as aromatherapy for relieving stress and pain parallel to chemical agents could be an important way to decrease the dose and side effects of analgesics. In a multicenter, single-blind trial, 40 patients who had open-heart surgery were recruited. Inclusion criteria were full consciousness, lack of hemorrhage, heart rate >60 beats/min, systolic blood pressure > 100 mmHg, and diastolic blood pressure > 60 mmHg, not using beta blockers in the operating room or ICU, no history of addiction to opioids or use of analgesics in regular, spontaneous breathing ability and not receiving synthetic opioids within 2 h before extubation. Ten minutes after extubation, the patients› vital signs [including BP, HR, Central Venous Pressure (CVP), SPO2, and RR] were measured. Then, a cotton swab, which was impregnated with 2 drops of Lavender essential oil 2%, was placed in patients' oxygen mask and patients breathed for 10 min. Thirty minutes after aromatherapy, the vital signs were measured again. Main objective of this study was the change in vital sign before and after aromatherapy. Statistical significance was accepted for P 0.001), diastolic blood pressure (p = 0.001), and heart rate (p = 0.03) before and after the intervention using paired t-test. Although, the results did not show any significant difference in respiratory rate (p = 0.1), SpO2 (p = 0.5) and CVP (p = 0.2) before and after inhaling Lavender essential oil. Therefore, the aromatherapy could effectively reduce blood pressure and heart rate in patients admitted to the open heart surgery ICU and can be used as an independent nursing intervention in stabilizing mentioned vital signs. The

Alberta Oil Sands Equity annual report, 1992-93. Partnership and progress in Alberta's oil sands development

International Nuclear Information System (INIS)

1993-01-01

Alberta Oil Sands Equity (AOSE) manages the Alberta government's equity investments in oil sands and heavy oil projects. AOSE is a 16.74% participant in the Syncrude Project, a 10% participant in the OSLO (Other Six Leases Operation) Commercial Project and the OSLO New Ventures project, and a 24.17% participant in the Lloydminster Bi-Provincial Upgrader. Syncrude produces ca 12% of Canadian crude oil requirements, and AOSE's share yielded $44 million profit for 1992/93, slightly higher than the the $43.3 million the previous year. The OSLO Commercial Project is a proposed commercial oil sands plant with a mine site and extraction plant to be located north of Fort McMurray, and an upgrading facility to be situated north of Edmonton. Work on this project was suspended in early 1992. The OSLO New Ventures project will handle the exploration and development of the remaining five oil sands leases plus the southern portion of Lease 31. As of March 31, 1993, the project owners were considering a commercial demonstration project utilizing dredging and cold-water extraction processes. Two of the owners are unable to provide funding and discussions are under way to resolve the matter and move the program forward. The Lloydminster Bi-Provincial Upgrader opened Noveber 20, 1992, and production has reached 41,000 bbl/d, or 89% of design capacity. The upgrader will increase the value of heavy crude oil and thereby increase its demand. 5 figs., 3 tabs

Bioremediation of marine oil pollution

International Nuclear Information System (INIS)

Gutnick, D.L.

1991-11-01

An assessment is presented of the scientific and technological developments in the area of bioremediation and biodegradation of marine oil pollution. A number of allied technologies are also considered. The basic technology in bioremediation involves adding fertilizers to an oil spill to enhance the natural process of oil biodegradation. Bioremediation can be applied to open systems such as beach or land spills, or in closed and controlled environments such as storage containers, specially constructed or modified bioreactors, and cargo tanks. The major advantage of using closed environments is the opportunity to control the physical and nutritional parameters to optimize the rate of biodegradation. An evaluation of the state of the art of bioremediation in Canada is also included. Recommendations are made to involve the Canadian Transportation Development Centre in short-term research projects on bioremediation. These projects would include the use of a barge as a mobile bioreactor for the treatment of off-loaded oily waste products, the use of in-situ bioremediation to carry out extensive cleaning, degassing, and sludge remediation on board an oil tanker, and the use of a barge as a mobile bioreactor and facility for the bioremediation of bilges. 51 refs., 4 figs., 14 tabs

Bioremediation of marine oil pollution

Energy Technology Data Exchange (ETDEWEB)

Gutnick, D L

1991-11-01

An assessment is presented of the scientific and technological developments in the area of bioremediation and biodegradation of marine oil pollution. A number of allied technologies are also considered. The basic technology in bioremediation involves adding fertilizers to an oil spill to enhance the natural process of oil biodegradation. Bioremediation can be applied to open systems such as beach or land spills, or in closed and controlled environments such as storage containers, specially constructed or modified bioreactors, and cargo tanks. The major advantage of using closed environments is the opportunity to control the physical and nutritional parameters to optimize the rate of biodegradation. An evaluation of the state of the art of bioremediation in Canada is also included. Recommendations are made to involve the Canadian Transportation Development Centre in short-term research projects on bioremediation. These projects would include the use of a barge as a mobile bioreactor for the treatment of off-loaded oily waste products, the use of in-situ bioremediation to carry out extensive cleaning, degassing, and sludge remediation on board an oil tanker, and the use of a barge as a mobile bioreactor and facility for the bioremediation of bilges. 51 refs., 4 figs., 14 tabs.

The global, centralized approach of the GAIN Premix Facility has made oil fortification in Indonesia more affordable.

Science.gov (United States)

Jallier, Vincent; Guyondet, Christophe; Provent, Adeline; Laillou, Arnaud; Soekirman; Moench-Pfanner, Regina

2013-06-01

Access to high-grade micronutrients is a recurring challenge that often threatens the long-term sustainability of food fortification programs. To assess the efficiency of the Global Alliance for Improved Nutrition (GAIN) Premix Facility in procuring quality, affordable vitamin A for fortification of edible oil in Indonesia. A global approach to procurement of standard items was used by combining volumes across various demand streams in order to reduce the total cost of acquisition through economies of scale. The GAIN Premix Facility undertook a detailed analysis of vitamin A requirements across its existing customer base, which served as a basis for developing a reliable demand forecast. A consolidated, competitive tender was launched that resulted in the setting up of a long-term commercial agreement with the selected supplier to lock in the most competitive price for a given period of time. The direct benefit to oil manufacturers of fortifying with vitamin A is that the cost of fortification went down significantly compared with prices they would have been offered had they ordered vitamin A individually. In Indonesia, this consolidated procurement approach has allowed a 14.5% decrease in the unit price of vitamin A. The GAIN Premix Facility demonstrated its effectiveness in acting as a global procurement platform by aggregating demand across different customers and leveraging improved prices through increased volumes. Building on the success of this effort, the GAIN Premix Facility is replicating this global approach for procurement of other standard items being procured across fortification programs worldwide.

Results from oil spill response research - an update

International Nuclear Information System (INIS)

Tennyson, E.J.

1993-01-01

Recent large oil spills from tankers have reaffirmed the need for continuing technology assessment and research to improve oil spill response capabilities. This paper discusses Minerals Management Service concerns, as reinforced by the acceleration of its research program in 1990. It briefly assesses current state-of-the-art technology for major aspects of spill response, including remote sensing, open-ocean containment and recovery, in-situ burning, use of chemical treating agents, beachline cleanup, and oil behavior. Specific research projects have begun to yield information that will improve detection and at-sea equipment performance; current projects include the development of an airborne laser-fluorosensor to determine whether apparent slicks contain oil. Additional projects involve the development of improved strategies for responding to oil in broken-ice conditions, for gaining an improved understanding of the fate and behavior of spilled oil as it affects response strategies, and for defining the capabilities of available dispersants and development of improved formulations. Recently, progress has been made on the development of safe and environmentally acceptable strategies to burn spilled oil in situ. The Ohmsett facility has been reopened and will be used to test prospective improvements in chemical treating agents and to develop standard procedures for testing and evaluating response equipment. Results of research published since the last Oil Spill Conference are discussed

Oil price shocks and economy: an open question

International Nuclear Information System (INIS)

Di Marzio, G.

2006-01-01

During the 1970s and 1980s advanced oil importing economies faced the adverse effects of oil supply disruptions with abrupt energy price rise, followed by sensible business cycle inversions and stagflation. The negative effects of the sharp energy price increase were amplified by factors such the induced costly resources reallocation between labour and capital, and between sectors of activity; rising uncertainty discouraging investments, and income redistribution consequences on aggregate demands After a shock the economic system generally adjusts in favour of less energy intensive industries; this leads pauses in production as part of the existing capital stock become obsolete, and causes resources under utilization. Since the 1970s a number of economists have been sceptical about why even large price shocks in a resource that accounts for less than 3-4 pct. of global GDP could cause losses of magnitude as those experienced in most advanced economies. They believe that monetary policy has played a role in generating the observed negative correlation between oil prices and economic activity, and question whether the post-oil-shock recessions were attributable to the oil price shocks themselves or to the monetary policy responding to these shocks. Empirical research largely shows a primary responsibility of large price shocks and major oil-supply disruptions on recessionary movements of GDP. Energy prices have risen sharply since 2003, driven by strengthening global demand; market fundamentals suggest that a considerable fraction of recent hikes will be permanent and current price levels remain credible. With limited spare capacity, the medium term oil supply-demand balance is expected to remain tight, and the price probably near current levels. Today' s high oil prices reflect the effects of sustained energy demand trends and, jointly, oil industry under investment during and after the low price era of the 1990s. The apparent moderate macro economic effects of the

Screensaver: an open source lab information management system (LIMS for high throughput screening facilities

Directory of Open Access Journals (Sweden)

Nale Jennifer

2010-05-01

Full Text Available Abstract Background Shared-usage high throughput screening (HTS facilities are becoming more common in academe as large-scale small molecule and genome-scale RNAi screening strategies are adopted for basic research purposes. These shared facilities require a unique informatics infrastructure that must not only provide access to and analysis of screening data, but must also manage the administrative and technical challenges associated with conducting numerous, interleaved screening efforts run by multiple independent research groups. Results We have developed Screensaver, a free, open source, web-based lab information management system (LIMS, to address the informatics needs of our small molecule and RNAi screening facility. Screensaver supports the storage and comparison of screening data sets, as well as the management of information about screens, screeners, libraries, and laboratory work requests. To our knowledge, Screensaver is one of the first applications to support the storage and analysis of data from both genome-scale RNAi screening projects and small molecule screening projects. Conclusions The informatics and administrative needs of an HTS facility may be best managed by a single, integrated, web-accessible application such as Screensaver. Screensaver has proven useful in meeting the requirements of the ICCB-Longwood/NSRB Screening Facility at Harvard Medical School, and has provided similar benefits to other HTS facilities.

Screensaver: an open source lab information management system (LIMS) for high throughput screening facilities.

Science.gov (United States)

Tolopko, Andrew N; Sullivan, John P; Erickson, Sean D; Wrobel, David; Chiang, Su L; Rudnicki, Katrina; Rudnicki, Stewart; Nale, Jennifer; Selfors, Laura M; Greenhouse, Dara; Muhlich, Jeremy L; Shamu, Caroline E

2010-05-18

Shared-usage high throughput screening (HTS) facilities are becoming more common in academe as large-scale small molecule and genome-scale RNAi screening strategies are adopted for basic research purposes. These shared facilities require a unique informatics infrastructure that must not only provide access to and analysis of screening data, but must also manage the administrative and technical challenges associated with conducting numerous, interleaved screening efforts run by multiple independent research groups. We have developed Screensaver, a free, open source, web-based lab information management system (LIMS), to address the informatics needs of our small molecule and RNAi screening facility. Screensaver supports the storage and comparison of screening data sets, as well as the management of information about screens, screeners, libraries, and laboratory work requests. To our knowledge, Screensaver is one of the first applications to support the storage and analysis of data from both genome-scale RNAi screening projects and small molecule screening projects. The informatics and administrative needs of an HTS facility may be best managed by a single, integrated, web-accessible application such as Screensaver. Screensaver has proven useful in meeting the requirements of the ICCB-Longwood/NSRB Screening Facility at Harvard Medical School, and has provided similar benefits to other HTS facilities.

Exploring Psychological and Aesthetic Approaches of Bio-Retention Facilities in the Urban Open Space

Directory of Open Access Journals (Sweden)

Suyeon Kim

2017-11-01

Full Text Available Over the last decades, a number of bio-retention facilities have been installed in urban areas for flood control and green amenity purposes. As urban amenity facilities for citizens, bio-retentions have a lot potential; however, the literature on bio-retentions focused mostly on physiochemical aspects like water quality and runoffs. Hence, this paper aims to explore psychological aspects of bio-retentions such as perceptions and landscape aesthetic value for visitors. In order to achieve this purpose, the study employed on-site interviews and questionnaires in the chosen three case studies as research methodology. For the 3 different locations of bio-retention facilities, interviews and questionnaires were carried out. The surveys of 100 bio-retention users were conducted, investigating their general perceptions and landscape aesthetics of the bio-retention facilities. The paper found that only 34% of the interviewees recognised bio-detention facilities, illustrating that most visitors were not aware of such facilities and were unable to distinguish the differences between bio-retention and conventional gardens. On the other hand, the majority of interviewees strongly supported the concept and function of bio-retentions, especially those who recognised the differences in planting species with conventional urban open spaces. Such main findings also encourage further studies of seeking quantitative values by conducting a correlation analysis between the functions and aesthetics of bio-retention facilities.

Multimegawatt space nuclear power open-cycle MHD-facility

International Nuclear Information System (INIS)

Pavshuk, V.A.; Panchenko, V.P.

2008-01-01

Paper presents the results of the efforts to calculate the characteristics, the layout and the engineering design of the open cycle space power propulsion on the basis of the high-temperature nuclear reactor for a nuclear rocket engine and the Faraday 20 MW capacity MHD-generator. The IVG-1 heterogeneous channel-vessel reactor ensuring in the course of the experiments hydrogen heating up to 3100 K, up to 5 MPa pressure at the reactor core outlet, up to 5 kg/s flowsheet, up to 220 MW thermal power served as a reactor is considered. One determined the MHD-generator basic parameters, namely: the portion of Cs dope was equal to 20%, the outlet stagnation pressure - 2 MPa, the electric conductivity - ≅30 S/m, the Mach number - ≅0.7, the magnetic field induction - 6 T, the capacity - 20 MW, the specific power removal - ∼4 MJ/kg. Paper describes the design of the MHD-facility with the working fluid momentless discharge and its basic characteristics [ru

Site Selection and Resource Allocation of Oil Spill Emergency Base for Offshore Oil Facilities

Science.gov (United States)

Li, Yunbin; Liu, Jingxian; Wei, Lei; Wu, Weihuang

2018-02-01

Based on the analysis of the historical data about oil spill accidents in the Bohai Sea, this paper discretizes oil spilled source into a limited number of spill points. According to the probability of oil spill risk, the demand for salvage forces at each oil spill point is evaluated. Aiming at the specific location of the rescue base around the Bohai Sea, a cost-benefit analysis is conducted to determine the total cost of disasters for each rescue base. Based on the relationship between the oil spill point and the rescue site, a multi-objective optimization location model for the oil spill rescue base in the Bohai Sea region is established. And the genetic algorithm is used to solve the optimization problem, and determine the emergency rescue base optimization program and emergency resources allocation ratio.

Application of H∞ Robust Control on a Scaled Offshore Oil and Gas De-Oiling Facility

DEFF Research Database (Denmark)

Løhndorf, Petar Durdevic; Yang, Zhenyu

2018-01-01

The offshore de-oiling process is a vital part of current oil recovery, as it separates the profitable oil from water and ensures that the discharged water contains as little of the polluting oil as possible. With the passage of time, there is an increase in the water fraction in reservoirs...... are inefficient in handling fluctuating inflows or complicated operating conditions. This work introduces a model-based robust H ∞ control solution that handles the entire de-oiling system and improves the system’s robustness towards fluctuating flow thereby improving the oil recovery and reducing...

Environmental assessment for the Strategic Petroleum Reserve Big Hill facility storage of commercial crude oil project, Jefferson County, Texas

International Nuclear Information System (INIS)

1999-03-01

The Big Hill SPR facility located in Jefferson County, Texas has been a permitted operating crude oil storage site since 1986 with benign environmental impacts. However, Congress has not authorized crude oil purchases for the SPR since 1990, and six storage caverns at Big Hill are underutilized with 70 million barrels of available storage capacity. On February 17, 1999, the Secretary of Energy offered the 70 million barrels of available storage at Big Hill for commercial use. Interested commercial users would enter into storage contracts with DOE, and DOE would receive crude oil in lieu of dollars as rental fees. The site could potentially began to receive commercial oil in May 1999. This Environmental Assessment identified environmental changes that potentially would affect water usage, power usage, and air emissions. However, as the assessment indicates, changes would not occur to a major degree affecting the environment and no long-term short-term, cumulative or irreversible impacts have been identified

Oil and gas in China: The door opens wider to international oil companies

International Nuclear Information System (INIS)

Tao, Wang

1993-01-01

This paper reviews new incentives offered by the China National Petroleum Corporation to help develop China's oil and gas fields. The initial offer for bids by foreign investors is for exploration and joint development contracts for western China's Tarim basin. However, the expansion to other basins and areas of China is well underway. It also discusses a pipeline project which will be connect the western China oil and gas fields with the eastern markets, approximately 2,200 miles. A historical review of the oil and gas production and utilization of China is presented along with forecasts of future production. It also provides estimates of gas and oil reserves and information on enhanced recovery techniques used to maintain a stable production level. The second half of the paper is an interview with Dr. Wang Tao, a PhD graduate of Moscow's Petroleum Institute, and president of the China National Petroleum Corporation. He reviews the government policies with regards to foreign investment in his country

A two year study of norm levels in the facilities of a major Malaysian oil and gas exploration and production company

International Nuclear Information System (INIS)

Bradley, D.A.

1996-01-01

Four comprehensive surveys of offshore and onshore facilities of a major Malaysian Oil and Gas E and P Company have been completed in the two year period since March 1993. Data include measurements of external gamma dose rate, space contamination, Rn and In progeny levels, particulate radioactivity in ambient air and radium in liquid effluent and sludge. Monitored quantities have yielded values which are for the most part in accord with those of undisturbed environments although limited occurrence of elevation of dose rate, and of radium concentration in sludge have been observed. In the latter instance measured concentrations of 226 Ra and 228 Ac have been within values of less than 1 Bq g -1 , being in general very much less than this. Comparison with reported oil and gas facility NORM levels in other parts of the world indicate present levels to be relatively low. (author)

DETERMINATION OF OPTIMAL CONTOURS OF OPEN PIT MINE DURING OIL SHALE EXPLOITATION, BY MINEX 5.2.3. PROGRAM

Directory of Open Access Journals (Sweden)

Miroslav Ignjatović

2013-04-01

Full Text Available By examination and determination of optimal solution of technological processes of exploitation and oil shale processing from Aleksinac site and with adopted technical solution and exploitation of oil shale, derived a technical solution that optimize contour of the newly defined open pit mine. In the world, this problem is solved by using a computer program that has become the established standard for quick and efficient solution for this problem. One of the computer’s program, which can be used for determination of the optimal contours of open pit mines is Minex 5.2.3. program, produced in Australia in the Surpac Minex Group Pty Ltd Company, which is applied at the Mining and Metallurgy Institute Bor (no. of licenses are SSI - 24765 and SSI - 24766. In this study, authors performed 11 optimization of deposit geo - models in Minex 5.2.3. based on the tests results, performed in a laboratory for soil mechanics of Mining and Metallurgy Institute, Bor, on samples from the site of Aleksinac deposits.

Mobil Oil Canada annual progress report to the Voluntary Challenge and Registry Program 1998

International Nuclear Information System (INIS)

1998-10-01

Mobil Oil Canada has prepared estimates of its emissions of major greenhouse gases for the years 1994, 1995, 1996 and 1997. While the Voluntary Challenge and Registry (VCR) encouraged an inventory of emissions for 1990 to the present, data are not present for earlier than 1994. An inventory summary is included that outlines the quantity of emissions due to the following sources for each facility: combustion of fuel gas for heaters, boilers and compressors, flaring and venting of natural gas, and consumption of coal generated electricity. For all Mobil operated facilities in 1997, GHG emissions existed in the following fractions: 43% due to fuel gas use, 42% due to gas flaring and venting, and 15% from electricity consumption. In 1996, emissions were more evenly distributed amongst the three major sources. A discussion is included of emissions produced and energy used by each process type with data shown in tables. This includes: heavy oil facilities, light oil facilities, sulfur recovery facilities, a sour gas facility, a sweet gas facility, and a thermal heavy oil facility. Various projects were undertaken at each Mobil operated facility to increase energy efficiency and reduce emissions. A summary of the fuel gas, electricity and emission savings for each facility is described, as well as the main actions responsible for each emission saving. These cover: light oil facilities, sulfur recovery facilities, a thermal heavy oil facility, a conventional heavy oil facility, a sweet gas facility, and a sour gas facility. 5 tabs., 9 figs

Louisiana's oil spill program : new developments

International Nuclear Information System (INIS)

Debusschere, K.; Tedford, R.; Brolin, J.; Lorentz, W.

2000-01-01

The Louisiana Oil Spill Coordinator's Office (LOSCO) was established to improve oil spill response, spill prevention and coordination. Louisiana is challenged with having the highest exposure of oil spills because a large portion of its economy is based on oil and gas exploration and production. LOSCO will find ways to minimize the risk of unauthorized oil spills and will address damage assessment and restoration efforts. The aging oil and gas infrastructure in Louisiana has also been recognized as a potential major source for oil spills. LOSCO locates potential spill locations and assesses the risks associated with the sites, some of which are 100 years old. LOSCO also initiated the following two programs: (1) the Abandoned Barge Program initiated in 1993 to remove abandoned barges that pose a high risk for oil discharge, and (2) the Abandoned Non-Hazardous Oil Waste (NOW) Pit and Facility Program initiated in 1992 to locate and remove structures, pits and wells that pose a risk for oil spills. About 25,000 facilities, pits, sumps and reservoirs have been inventoried and evaluated to determine if they pose a risk to human health or the environment. The Louisiana Oil Spill Prevention and Response Act (OSPRA) of 1991 allocates up to $2 million per year for the abatement of oil spills from abandoned facilities in Louisiana. The state legislature has also created the Applied and Educational Oil Spill Research and Development Program (OSRADP) to fund oil spill research. Since 1993, OSRADP has granted 68 awards in support of 42 projects, many of which focused on recovery and cleanup methods including in-situ burning, fate and effect of oil in Louisiana environments, bioremediation, phytoremediation, composting, chemical cleaners, dispersants, sorbents, and solidifiers. 3 refs., 1 tab

. Estimating soil contamination from oil spill using neutron backscattering technique

International Nuclear Information System (INIS)

Okunade, I.O.; Jonah, S.A.; Abdulsalam, M.O.

2009-01-01

An analytical facility which is based on neutron backscattering technique has been adapted for monitoring oil spill. The facility which consists of 1 Ci Am-Be isotopic source and 3 He neutron detector is based on the principle of slowing down of neutrons in a given medium which is dominated by the elastic process with the hydrogen nucleus. Based on this principle, the neutron reflection parameter in the presence of hydrogenous materials such as coal, crude oil and other hydrocarbon materials depends strongly on the number of hydrogen nuclei present. Consequently, the facility has been adapted for quantification of crude oil in soil contaminated in this work. The description of the facility and analytical procedures for quantification of oil spill in soil contaminated with different amount of crude oil are provided

EPA Linked Open Data: Facility Registry Service

Data.gov (United States)

U.S. Environmental Protection Agency — The Facility Registry Service (FRS) identifies facilities, sites, or places subject to environmental regulation or of environmental interest to EPA programs or...

Combined pretreatment with hot compressed water and wet disk milling opened up oil palm biomass structure resulting in enhanced enzymatic digestibility.

Science.gov (United States)

Zakaria, Mohd Rafein; Hirata, Satoshi; Fujimoto, Shinji; Hassan, Mohd Ali

2015-10-01

Combined pretreatment with hot compressed water and wet disk milling was performed with the aim to reduce the natural recalcitrance of oil palm biomass by opening its structure and provide maximal access to cellulase attack. Oil palm empty fruit bunch and oil palm frond fiber were first hydrothermally pretreated at 150-190° C and 10-240 min. Further treatment with wet disk milling resulted in nanofibrillation of fiber which caused the loosening of the tight biomass structure, thus increasing the subsequent enzymatic conversion of cellulose to glucose. The effectiveness of the combined pretreatments was evaluated by chemical composition changes, power consumption, morphological alterations by SEM and the enzymatic digestibility of treated samples. At optimal pretreatment process, approximately 88.5% and 100.0% of total sugar yields were obtained from oil palm empty fruit bunch and oil palm frond fiber samples, which only consumed about 15.1 and 23.5 MJ/kg of biomass, respectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

Global Integration, Non-Oil Export and Economic Growth in Nigeria

Directory of Open Access Journals (Sweden)

Ozoemena Stanley Nwodo

2017-03-01

Full Text Available This study focuses on global integration, non-oil export and economic growth in Nigeria. The direct and interaction effect of the both openness variables and non-oil export on economic growth in Nigeria is investigated using quarterly data from 1986-2014. For analysis, it uses one measures of financial openness: de facto (total capital flow variables following Aizenman and Noy (2009.and a measure of trade openness adopted by Okoh (2004. The study applies the Autoregressive Distributed Lag Model (ARDL. The results show positive impact of non-oil export on economic growth in Nigeria both in the short run and in the long run, negative effect of trade and financial openness on economic growth however, the result recorded a negative effect of the interaction of trade openness and non-oil export on economic growth and a positive effect of the interaction of financial openness and non-oil export on economic growth. Thus, the study recommends among others that government should get the fundamentals right in the economy first that will boost non-oil sector before opening the economy for trade.

Incineration of contaminated oil from Sellafield - 16246

International Nuclear Information System (INIS)

Broadbent, Craig; Cassidy, Helen; Stenmark, Anders

2009-01-01

Studsvik have been incinerating Low Level Waste (LLW) at its licensed facility in Sweden since the mid-1970's. This process not only enables the volume of waste to be significantly reduced but also produces an inert residue suitable for final disposal. The facility has historically incinerated only solid dry LLW, however in 2008 an authorisation was obtained to permit the routine incineration of LLW contaminated oil at the facility. Prior to obtaining the authorisation to incinerate oils and other organic liquids - both from clean-up activities on the Studsvik site and on a commercial basis - a development program was established. The primary aims of this were to identify the optimum process set-up for the incinerator and also to demonstrate to the regulatory authorities that the appropriate environmental and radiological parameters would be maintained throughout the new process. The final phase of the development program was to incinerate a larger campaign of contaminated oil from the nuclear industry. A suitable accumulation of oil was identified on the Sellafield site in Cumbria and a commercial contract was established to incinerate approximately 40 tonnes of oil from the site. The inventory of oil chosen for the trial incineration represented a significant challenge to the incineration facility as it had been generated from various facilities on-site and had degraded significantly following years of storage. In order to transport the contaminated oil from the Sellafield site in the UK to the Studsvik facility in Sweden several challenges had to be overcome. These included characterisation, packaging and international transportation (under a Transfrontier Shipment (TFS) authorisation) for one of the first transports of liquid radioactive wastes outside the UK. The incineration commenced in late 2007 and was successfully completed in early 2008. The total volume reduction achieved was greater than 97%, with the resultant ash packaged and returned to the UK (for

Alberta oil sands crudes : upgrading and marketing

International Nuclear Information System (INIS)

Ashar, M.

2008-01-01

Open pit mining and in situ techniques, such as steam stimulation, are used to recover Alberta's bitumen and heavy oil resources, which have higher viscosities than conventional hydrocarbons. The bitumen is typically upgraded to synthetic crude oil (SCO). In the simplest processing scheme, the bitumen is blended with diluent for ease in pipeline transport and then processed at refineries with upgrading facilities. The bitumen is also upgraded to light SCO at world-scale upgraders in Alberta. The SCO is then processed at refineries in downstream markets. The 2 categories of upgrading, notably primary and secondary upgrading, were described in this article along with technology options for both categories. Slurry hydrocracking is regarded as the most interesting emerging residual fuel upgrading technology. It combines special catalyst mixes with the latest slurry reactor designs as well as innovative catalyst capture and recycle schemes to produce very high conversions and potentially superior upgrading economics. The increase in volume and rate of SCO from Alberta provides refiners in the oil sands marketing sector an unprecedented choice of opportunities to improve profitability. Key trends indicate that production will increase substantially from 2008 to 2030. 5 figs

Alberta oil sands crudes : upgrading and marketing

Energy Technology Data Exchange (ETDEWEB)

Ashar, M. [Suncor Energy, Fort McMurray, AB (Canada)

2008-05-15

Open pit mining and in situ techniques, such as steam stimulation, are used to recover Alberta's bitumen and heavy oil resources, which have higher viscosities than conventional hydrocarbons. The bitumen is typically upgraded to synthetic crude oil (SCO). In the simplest processing scheme, the bitumen is blended with diluent for ease in pipeline transport and then processed at refineries with upgrading facilities. The bitumen is also upgraded to light SCO at world-scale upgraders in Alberta. The SCO is then processed at refineries in downstream markets. The 2 categories of upgrading, notably primary and secondary upgrading, were described in this article along with technology options for both categories. Slurry hydrocracking is regarded as the most interesting emerging residual fuel upgrading technology. It combines special catalyst mixes with the latest slurry reactor designs as well as innovative catalyst capture and recycle schemes to produce very high conversions and potentially superior upgrading economics. The increase in volume and rate of SCO from Alberta provides refiners in the oil sands marketing sector an unprecedented choice of opportunities to improve profitability. Key trends indicate that production will increase substantially from 2008 to 2030. 5 figs.

Succession of Deferribacteres and Epsilonproteobacteria through a nitrate-treated high-temperature oil production facility

DEFF Research Database (Denmark)

Gittel, Antje; Kofoed, Michael; Sørensen, Ketil B

2012-01-01

, Denmark) and aimed to assess their potential in souring control. Nitrate addition to deoxygenated seawater shifted the low-biomass seawater community dominated by Gammaproteobacteria closely affiliated with the genus Colwellia to a high-biomass community with significantly higher species richness....... Epsilonproteobacteria accounted for less than 1% of the total bacterial community in the nitrate-amended injection water and were most likely outcompeted by putative nitrate-reducing, methylotrophic Gammaproteobacteria of the genus Methylophaga. Reservoir passage and recovery of the oil resulted in a significant change...... abundance of Epsilonproteobacteria throughout the production facility suggested that the Deferribacteres play a major role in nitrate-induced souring control at high temperatures....

Molecular detection of canine parvovirus in flies (Diptera) at open and closed canine facilities in the eastern United States.

Science.gov (United States)

Bagshaw, Clarence; Isdell, Allen E; Thiruvaiyaru, Dharma S; Brisbin, I Lehr; Sanchez, Susan

2014-06-01

to determine the correlation of fly CPV status (positive or negative) for each facility, facility design (open or closed), mean number of dogs present monthly and number of flies captured. Significant differences occurred between fly CPV positive vs. negative sites with regard to their CPV case numbers, fly numbers captured, and number of dogs present. At the ASL, a statistically significant relationship was found between PCR-determined fly CPV status (positive or negative) and facility design (open vs. closed). Open-facility designs were likely to have more CPV outbreaks and more likely to have flies testing positive for CPV DNA. Copyright © 2014 Elsevier B.V. All rights reserved.

Economic impacts of oil spills: Spill unit costs for tankers, pipelines, refineries, and offshore facilities. [Task 1, Final report

Energy Technology Data Exchange (ETDEWEB)

1993-10-15

The impacts of oil spills -- ranging from the large, widely publicized Exxon Valdez tanker incident to smaller pipeline and refinery spills -- have been costly to both the oil industry and the public. For example, the estimated costs to Exxon of the Valdez tanker spill are on the order of $4 billion, including $2.8 billion (in 1993 dollars) for direct cleanup costs and $1.125 billion (in 1992 dollars) for settlement of damages claims caused by the spill. Application of contingent valuation costs and civil lawsuits pending in the State of Alaska could raise these costs appreciably. Even the costs of the much smaller 1991 oil spill at Texaco`s refinery near Anacortes, Washington led to costs of $8 to 9 million. As a result, inexpensive waming, response and remediation technologies could lower oil spin costs, helping both the oil industry, the associated marine industries, and the environment. One means for reducing the impact and costs of oil spills is to undertake research and development on key aspects of the oil spill prevention, warming, and response and remediation systems. To target these funds to their best use, it is important to have sound data on the nature and size of spills, their likely occurrence and their unit costs. This information could then allow scarce R&D dollars to be spent on areas and activities having the largest impact. This report is intended to provide the ``unit cost`` portion of this crucial information. The report examines the three key components of the US oil supply system, namely, tankers and barges; pipelines and refineries; and offshore production facilities. The specific purpose of the study was to establish the unit costs of oil spills. By manipulating this key information into a larger matrix that includes the size and frequency of occurrence of oil spills, it will be possible` to estimate the likely future impacts, costs, and sources of oil spills.

Participation of civil engineers in designing facilities in rock salt

International Nuclear Information System (INIS)

Duddeck, H.; Westhaus, T.

1990-01-01

For the design of underground facilities in rock salt layers or domes, as caverns for repositories, the civil engineering approach may be useful. The underground openings are analysed by determining the displacements and the stresses for actual states and hypothetical situations. The paper reports on the state of art in the development of suited time dependent material laws for rock salt, on time integration methods for the analysis, and on a possible procedure for a consistent safety analysis. The examples given include caverns filled by oil, analysis of a mine with vertical excavation chambers, and dams closing mine galleries. (orig.) [de

Oil spill preparedness in the Mediterranean Sea

International Nuclear Information System (INIS)

Jorigne, E.M.; Wong, K.V.

1993-01-01

Over 15% of the world's consumption of crude oil and refined products is shipped through the Mediterranean Sea each year. The sea is one of the most polluted areas in the world and has areas of high risk for oil spills, notably those places where there is a very narrow passage between coasts or islands. The region also needs to modernize its ports by developing more deballasting facilities, since a large percentage of spill accidents happens during terminal operations. Release of oily wastes from ships is also significant. The World Bank Global Environment Facility trust fund is working on a project to help the southwest Mediterranean countries modernize reception facilities for ballast water, bilge water, and oily waste water. The Regional Marine Pollution Emergency Response Center (REMPEC) in Malta acts as the coordinating center for regional contingency planning for oil spill response. The cost of the port facilities modernization program and oil spill contingency plan implementation for the Mediterranean is estimated at US$444 million. An allocation of costs is suggested which will help those countries needing more financial aid to implement the proposed programs. In the long run, the cost of these programs will be much lower than that of a massive oil spill cleanup. 7 refs., 2 figs., 4 tabs

Sites Requiring Facility Response Plans, Geographic NAD83, EPA (2006) [facility_response_plan_sites_la_EPA_2007

Data.gov (United States)

Louisiana Geographic Information Center — Locations of facilities in Louisiana requiring Oil Pollution Act (OPA) Facility Response Plans (FRP). The dataset was provided by the Region 6 OSCARS program....

Survey of existing underground openings for in-situ experimental facilities

International Nuclear Information System (INIS)

Wollenberg, H.; Graf, A.; Strisower, B.; Korbin, G.

1981-07-01

In an earlier project, a literature search identified 60 underground openings in crystalline rock capable of providing access for an in-situ experimental facility to develop geochemical and hydrological techniques for evaluating sites for radioactive waste isolation. As part of the current project, discussions with state geologists, owners, and operators narrowed the original group to 14. Three additional sites in volcanic rock and one site in granite were also identified. Site visits and application of technical criteria, including the geologic and hydrologic settings and depth, extent of the rock unit, condition, and accessibility of underground workings, determined four primary candidate sites: the Helms Pumped Storage Project in grandiodorite of the Sierra Nevada, California; the Tungsten Queen Mine in Precambrian granodiorite of the North Carolina Piedmont; the Mount Hope Mine in Precambrian granite and gneiss of northern New Jersey; and the Minnamax Project in the Duluth gabbro complex of northern Minnesota

Oil removal of spent hydrotreating catalyst CoMo/Al2O3 via a facile method with enhanced metal recovery.

Science.gov (United States)

Yang, Yue; Xu, Shengming; Li, Zhen; Wang, Jianlong; Zhao, Zhongwei; Xu, Zhenghe

2016-11-15

Deoiling process is a key issue for recovering metal values from spent hydrotreating catalysts. The oils can be removed with organic solvents, but the industrialized application of this method is greatly hampered by the high cost and complex processes. Despite the roasting method is simple and low-cost, it generates hardest-to-recycle impurities (CoMoO4 or NiMoO4) and enormous toxic gases. In this study, a novel and facile approach to remove oils from the spent hydrotreating catalysts is developed. Firstly, surface properties of spent catalysts are characterized to reveal the possibility of oil removal. And then, oils are removed with water solution under the conditions of 90°C, 0.1wt% SDS, 2.0wt% NaOH and 10ml/gL/S ratio for 4h. Finally, thermal treatment and leaching tests are carried out to further explore the advantages of oil removal. The results show that no hardest-to-recycle impurity CoMoO4 is found in XPS spectra of thermally treated samples after deoiling and molybdenum is leached completely with sodium carbonate solution. It means that the proposed deoiling method can not only remove oils simply and without enormous harmful gases generating, but also avoid the generation of detrimental impurity and promote recycling of valuable metals from spent hydrotreating catalysts. Copyright © 2016 Elsevier B.V. All rights reserved.

Carbon Capture and Sequestration (via Enhanced Oil Recovery) from a Hydrogen Production Facility in an Oil Refinery

Energy Technology Data Exchange (ETDEWEB)

Stewart Mehlman

2010-06-16

The project proposed a commercial demonstration of advanced technologies that would capture and sequester CO2 emissions from an existing hydrogen production facility in an oil refinery into underground formations in combination with Enhanced Oil Recovery (EOR). The project is led by Praxair, Inc., with other project participants: BP Products North America Inc., Denbury Onshore, LLC (Denbury), and Gulf Coast Carbon Center (GCCC) at the Bureau of Economic Geology of The University of Texas at Austin. The project is located at the BP Refinery at Texas City, Texas. Praxair owns and operates a large hydrogen production facility within the refinery. As part of the project, Praxair would construct a CO2 capture and compression facility. The project aimed at demonstrating a novel vacuum pressure swing adsorption (VPSA) based technology to remove CO2 from the Steam Methane Reformers (SMR) process gas. The captured CO2 would be purified using refrigerated partial condensation separation (i.e., cold box). Denbury would purchase the CO2 from the project and inject the CO2 as part of its independent commercial EOR projects. The Gulf Coast Carbon Center at the Bureau of Economic Geology, a unit of University of Texas at Austin, would manage the research monitoring, verification and accounting (MVA) project for the sequestered CO2, in conjunction with Denbury. The sequestration and associated MVA activities would be carried out in the Hastings field at Brazoria County, TX. The project would exceed DOE’s target of capturing one million tons of CO2 per year (MTPY) by 2015. Phase 1 of the project (Project Definition) is being completed. The key objective of Phase 1 is to define the project in sufficient detail to enable an economic decision with regard to proceeding with Phase 2. This topical report summarizes the administrative, programmatic and technical accomplishments completed in Phase 1 of the project. It describes the work relative to project technical and design activities

Contaminant Characterization of Effluent from Pennsylvania Brine Treatment, Inc., Josephine Facility: Implications for Disposal of Oil and Gas Flowback Fluids from Brine Treatment Plants

Science.gov (United States)

The PBT-Josephine Facility accepts only wastewater from the oil and gas industry. This report describes the concentrations of selected contaminants in the effluent water and compares the contaminant effluent concentrations to state and federal standards.

Research Capabilities for Oil-Free Turbomachinery Expanded by New Rotordynamic Simulator Facility

Science.gov (United States)

Howard, Samuel A.

2004-01-01

A new test rig has been developed for simulating high-speed turbomachinery shafting using Oil-Free foil air bearing technology. Foil air journal bearings are self-acting hydrodynamic bearings with a flexible inner sleeve surface using air as the lubricant. These bearings have been used in turbomachinery, primarily air cycle machines, for the past four decades to eliminate the need for oil lubrication. More recently, interest has been growing in applying foil bearings to aircraft gas turbine engines. They offer potential improvements in efficiency and power density, decreased maintenance costs, and other secondary benefits. The goal of applying foil air bearings to aircraft gas turbine engines prompted the fabrication of this test rig. The facility enables bearing designers to test potential bearing designs with shafts that simulate the rotating components of a target engine without the high cost of building actual flight hardware. The data collected from this rig can be used to make changes to the shaft and bearings in subsequent design iterations. The rest of this article describes the new test rig and demonstrates some of its capabilities with an initial simulated shaft system. The test rig has two support structures, each housing a foil air journal bearing. The structures are designed to accept any size foil journal bearing smaller than 63 mm (2.5 in.) in diameter. The bearing support structures are mounted to a 91- by 152-cm (3- by 5-ft) table and can be separated by as much as 122 cm (4 ft) and as little as 20 cm (8 in.) to accommodate a wide range of shaft sizes. In the initial configuration, a 9.5-cm (3.75-in.) impulse air turbine drives the test shaft. The impulse turbine, as well as virtually any number of "dummy" compressor and turbine disks, can be mounted on the shaft inboard or outboard of the bearings. This flexibility allows researchers to simulate various engine shaft configurations. The bearing support structures include a unique bearing mounting

40 CFR 279.43 - Used oil transportation.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Used oil transportation. 279.43... Facilities § 279.43 Used oil transportation. (a) Deliveries. A used oil transporter must deliver all used oil... comply with all applicable requirements under the U.S. Department of Transportation regulations in 49 CFR...

The impact of oil and natural gas facilities on rural residential property values

International Nuclear Information System (INIS)

Boxall, P.C.

2005-01-01

This PowerPoint presentation examined challenges in the economic valuation of environmental changes within the context of formal real estate markets. It was proposed that some values that are expressed in markets can be affected by environmental changes and should be used in resource development land assessments. Details of indirect market valuation and revealed preference methods were reviewed. An outline of hedonic pricing was presented. It was noted that hedonic pricing can be used with other market values and prices such as tourism, art prices and hotel prices, where multivariate regression techniques are used and regression coefficients reveal information on the implicit prices of certain characteristics. Property value examples in the environmental economics literature were reviewed. A case study using data from eco-terrorism costs was presented. Issues concerning sour gas facilities were discussed with reference to public anxiety over hydrogen sulfide (H 2 S) toxicity and flares. Concerns over health risks and negative amenity impacts were discussed. The impacts of sour gas facilities on property values of residential acreages in and around Calgary were considered, and a map of the study area was presented. An outline of emergency plan response zones was provided. Price effects of industry facilities were presented, including marginal and cumulative impacts on price. It was concluded that oil and gas activities have significant impacts on rural residential property prices, but that industry members currently report that there is little to no effect. It was suggested that the research presented in this paper could be used to assess levels of compensation. tabs., figs

Open Access Centre at the Nature Research Centre: a facility for enhancement of scientific research, education and public outreach in Lithuania

Science.gov (United States)

Šerpenskienė, Silvija; Skridlaitė, Gražina

2014-05-01

Open Access Centre (OAC) was established in Vilnius, Lithuania in 2013 as a subdivision of the Nature Research Centre (NRC) operating on the principle of open access for both internal and external users. The OAC consists of 15 units, i.e. 15 NRC laboratories or their branches. Forty four sets of research equipment were purchased. The OAC cooperates with Lithuanian science and studies institutions, business sector and other governmental and public institutions. Investigations can be carried in the Geosciences, Biotaxonomy, Ecology and Molecular Research, and Ecotoxicology fields. Environmental radioactivity, radioecology, nuclear geophysics, microscopic and chemical composition of natural compounds (minerals, rocks etc.), paleomagnetic, magnetic and environmental investigations, as well as ground and water contamination by oil products and other organic environment polluting compounds, identification of fossils, rocks and minerals can be studied in the Georesearch field. Ecosystems and identification of plants, animals and microorganisms are main subjects of the Biotaxonomy, Ecology and Molecular Research field. The Ecotoxicologal Research deals with toxic and genotoxic effects of toxic substances and other sources of pollution on macro- and microorganisms and cell cultures. Open access is guaranteed by: (1) providing scientific research and experimental development services; (2) implementing joint business and science projects; (3) using facilities for the training of specialists of the highest qualifications; (4) providing properly qualified and technically trained users with opportunities to carry out their scientific research and/or experiments in the OAC laboratories by themselves. Services provided in the Open Access Centre can be received by both internal and external users: persons undertaking innovative economic activities, students of other educational institutions, interns, external teams of researchers engaged in scientific research activities, teachers

Final closure plan for the high-explosives open burn treatment facility at Lawrence Livermore National Laboratory Experimental Test Site 300

Energy Technology Data Exchange (ETDEWEB)

Mathews, S.

1997-04-01

This document addresses the interim status closure of the HE Open Bum Treatment Facility, as detailed by Title 22, Division 4.5, Chapter 15, Article 7 of the Califonia Code of Regulations (CCR) and by Title 40, Code of Federal Regulations (CFR) Part 265, Subpart G, ``Closure and Post Closure.`` The Closure Plan (Chapter 1) and the Post- Closure Plan (Chapter 2) address the concept of long-term hazard elimination. The Closure Plan provides for capping and grading the HE Open Bum Treatment Facility and revegetating the immediate area in accordance with applicable requirements. The Closure Plan also reflects careful consideration of site location and topography, geologic and hydrologic factors, climate, cover characteristics, type and amount of wastes, and the potential for contaminant migration. The Post-Closure Plan is designed to allow LLNL to monitor the movement, if any, of pollutants from the treatment area. In addition, quarterly inspections will ensure that all surfaces of the closed facility, including the cover and diversion ditches, remain in good repair, thus precluding the potential for contaminant migration.

Oil spills in open seas and harbours - impact on marine environment

International Nuclear Information System (INIS)

Siddiqui, S.H.

1995-01-01

In this article the environmental impacts of sea water near Karachi (Pakistan) harbour (Arabian Sea) are discussed. The water pollution is caused due to oil leakage from ships. The toxicity of various oils (crude oils and refined oils) to different species of marine varies greatly. The second main source of water is municipal waste water. For the control of sea water pollution, there must be education as lack of awareness of the public to ask for clean beaches and absence of coordination between concerned oil companies, tanker operating agencies, port authorities and government (A.B.)

Thermoset polymers via ring opening metathesis polymerization of functionalized oils

Science.gov (United States)

Larock, Richard C; Henna, Phillip H; Kessier, Michael R

2012-11-27

The invention provides a method for producing a thermosetting resin from renewable oils, the method comprising supplying renewable oil molecules containing strained ring alkene moieties; reacting the alkene moieties with cyclic alkenes to create a polymer; and repeating the above two steps until the resin having desired characteristics are obtained. Also provided is a thermoset resin comprising functionalized renewable oil polymerized with a co-monomer.

Access to Posthospitalization Acute Care Facilities is Associated with Payer Status for Open Abdominal Aortic Repair and Open Lower Extremity Revascularization in the Vascular Quality Initiative.

Science.gov (United States)

Ulloa, Jesus G; Woo, Karen; Tseng, Chi-Hong; Maggard-Gibbons, Melinda; Rigberg, David

2017-07-01

Uninsured patients may not have access to postacute care facilities that play an important role in clinical recovery, and functional outcomes after vascular surgery. We sought to determine whether discharge disposition is associated with insurance status. We retrospectively reviewed data from the Vascular Quality Initiative ® for patients who underwent open abdominal aortic repair, infrainguinal bypass, or suprainguinal bypass (SB) between January 2012 and July 2015. Mixed-effects logistic regression analysis with clustering at the surgeon and facility level was used to calculate 95% confidence intervals for discharge disposition to home, skilled nursing facility (SNF) or rehabilitation (Rehab) facility by payer status (Medicare, Medicaid, Commercial, Military/Veterans Affairs, Non-US Insurance, or Self-pay), with adjustment for patient, operative, and postoperative characteristics. The study cohort comprised 18,478 procedures (open abdominal aortic repair = 2,817; infrainguinal bypass = 11,572; suprainguinal bypass = 4,089) after we excluded procedures with missing data and in-hospital deaths. Twenty-four percent of the cohort was discharged to an SNF or Rehab site. On univariate analysis, the odds ratio (OR) of discharge home was 4.38 (95% CI: 3.33-5.77) for self-pay as compared to Medicare. On mixed-effects analysis, the adjusted odds of discharge home for self-pay as compared to Medicare remained high (OR = 3.09; 95% CI: 2.23-4.26), after adjustment for age, gender, race/ethnicity, preoperative ambulatory status, number of comorbidities, case urgency, total operative time, presence of a postoperative complication, procedure type, and length of stay. Adjusted odds for discharge to SNF (OR = 0.26; 95% CI: 0.15-0.46) and Rehab (OR = 0.50; 95% CI: 0.35-0.72) were lowest for self-pay status. Access to postacute care facilities is associated with insurance status. Self-pay (uninsured) patients are less likely to have access to discharge services that may

Oil shale activities in China

International Nuclear Information System (INIS)

Peng, D.; Jialin, Q.

1991-01-01

China has abundant oil shale resources, of the Early Silurian to Neogene age, the most important being the Tertiary period. The proved oil shale reserves in Fushun amount to 3.6 billion t, in Maoming 4.1 billion t. In Fushun, oil shale is produced by open-pit mining as a byproduct of coal, in Maoming it is also mined in open pits, but without coal. In China, scale oil has been produced from oil shale for 60 years. Annual production of crude shale oil amounts to about 200 000 t. The production costs of shale oil are lower than the price of crude petroleum on the world market. China has accumulated the experience and technologies of oil shale retorting. The Fushun type retort has been elaborated, in which the latent and sensible heat of shale coke is well utilized. But the capacity of such retort is relatively small, therefore it is suitable for use in small or medium oil plants. China has a policy of steadily developing shale oil industry. China is conducting oil shale research and developing oil shale processing technology. Much attention is being pay ed to the comprehensive utilization of oil shale, shale oil, and to environmental problems. In China, oil shale is mostly used for producing shale by retorting, attention will also be paid to direct combustion for power generation. Great achievements in oil shale research have been made in the eighties, and there will be a further development in the nineties. (author), 12 refs., 3 tabs

Facility Response Plan (FRP) Points, Region 9, 2014, US EPA Region 9

Data.gov (United States)

U.S. Environmental Protection Agency — A Facility Response Plan (FRP) demonstrates a facility's preparedness to respond to a worst case oil discharge. Under the Clean Water Act, as amended by the Oil...

Facility Response Plan (FRP) Points, Region 9, 2013, US EPA Region 9

Data.gov (United States)

U.S. Environmental Protection Agency — A Facility Response Plan (FRP) demonstrates a facility's preparedness to respond to a worst case oil discharge. Under the Clean Water Act, as amended by the Oil...

Facility Response Plan (FRP) Points, Region 9, 2012, US EPA Region 9

Data.gov (United States)

U.S. Environmental Protection Agency — A Facility Response Plan (FRP) demonstrates a facility's preparedness to respond to a worst case oil discharge. Under the Clean Water Act, as amended by the Oil...

The Effectiveness Test of Oil Phase Ointment Containing Snakehead Fish (Channa striata Extract on Open Stage II Acute Wounded Wistar Strain Male Rats

Directory of Open Access Journals (Sweden)

Fransisca Daisa

2017-08-01

Full Text Available The snakehead (Channa striata contained fatty acids omega-3 and omega-6 are useful as nutrients in accelerating the wound healing process. This study aims to determine the effectiveness of the oil phase extract ointment snakehead in the healing of acute wounds open stage II. Testing the effectiveness of wound healing using 6 groups: normal, gel bioplacenton (positive control, ointment base (negative control, ointments snakehead extract oil phase concentration of 10; 20 and 40% of the 4 rats with acute wounds open stage II and observation until day 16 injury. The area of the wound was measured with the image J program Macbiophotonic, calculated% healing power, and AUC values. A statistical test to the total AUC values per rat with SPSS for Windows 22.0 program using One Way ANOVA and Post-hoc LSD test. The results showed a significant difference in the negative group with ointment concentration of 20% (p <0.05. The treatment group phase ointment fish oil extract is effective for wound healing is best to have a concentration of 20% for percentage of wound healing power of 97.157% and the average AUC value of 865.683% of the day.

Sustaining and Extending the Open Science Grid: Science Innovation on a PetaScale Nationwide Facility (DE-FC02-06ER41436) SciDAC-2 Closeout Report

Energy Technology Data Exchange (ETDEWEB)

Livny, Miron [Univ. of Wisconsin, Madison, WI (United States); Shank, James [Boston Univ., MA (United States); Ernst, Michael [Brookhaven National Lab. (BNL), Upton, NY (United States); Blackburn, Kent [California Inst. of Technology (CalTech), Pasadena, CA (United States); Goasguen, Sebastien [Clemson Univ., SC (United States); Tuts, Michael [Columbia Univ., New York, NY (United States); Gibbons, Lawrence [Cornell Univ., Ithaca, NY (United States); Pordes, Ruth [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Sliz, Piotr [Harvard Medical School, Boston, MA (United States); Deelman, Ewa [Univ. of Southern California, Los Angeles, CA (United States). Information Sciences Inst.; Barnett, William [Indiana Univ., Bloomington, IN (United States); Olson, Doug [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); McGee, John [Univ. of North Carolina, Chapel Hill, NC (United States). Renaissance Computing Inst.; Cowles, Robert [SLAC National Accelerator Lab., Menlo Park, CA (United States); Wuerthwein, Frank [Univ. of California, San Diego, CA (United States); Gardner, Robert [Univ. of Chicago, IL (United States); Avery, Paul [Univ. of Florida, Gainesville, FL (United States); Wang, Shaowen [Univ. of Illinois, Champaign, IL (United States); Univ. of Iowa, Iowa City, IA (United States); Lincoln, David Swanson [Univ. of Nebraska, Lincoln, NE (United States)

2015-02-11

Under this SciDAC-2 grant the project’s goal w a s t o stimulate new discoveries by providing scientists with effective and dependable access to an unprecedented national distributed computational facility: the Open Science Grid (OSG). We proposed to achieve this through the work of the Open Science Grid Consortium: a unique hands-on multi-disciplinary collaboration of scientists, software developers and providers of computing resources. Together the stakeholders in this consortium sustain and use a shared distributed computing environment that transforms simulation and experimental science in the US. The OSG consortium is an open collaboration that actively engages new research communities. We operate an open facility that brings together a broad spectrum of compute, storage, and networking resources and interfaces to other cyberinfrastructures, including the US XSEDE (previously TeraGrid), the European Grids for ESciencE (EGEE), as well as campus and regional grids. We leverage middleware provided by computer science groups, facility IT support organizations, and computing programs of application communities for the benefit of consortium members and the US national CI.

Evaluating oil/water separators

International Nuclear Information System (INIS)

Murdoch, M.A.

1993-01-01

Four commercially available oil/water separators were tested at an oil refinery test facility. The separators were the Alfa-Laval OFPX 413 disk-stack centrifuge, the Conoco Vortoil hydrocyclone system, International Separation Technology's Intr-Septor 250, and a modified Flo Trend gravity separator. Each machine was tested against mixtures of salt water and crude oil, and mixtures of salt water and a water-in-oil emulsion. The impact on separator performance from simulated sea motion, and from the addition of emulsion breakers and debris to the influent, were also evaluated. The test equipment, instrumentation, analysis facilities, test plans, and procedures to conduct the tests are described, but test results are not reported. Recommendations for improved test procedures are included. The inability to accurately monitor flow rates was found to have the greatest negative impact on test performance and results. Aspects of the test program that worked well included the use of flexible and semi-rigid hoses for customizing the test setups, the use of modular and leased tanks, and the sea motion simulator swing table design. 3 refs., 2 tabs

Developing standardized facility contingency plans

International Nuclear Information System (INIS)

Davidson, D.A.

1993-01-01

Texaco consists of several operating departments that are, in effect, independent companies. Each of these departments is responsible for complying with all environmental laws and regulations. This includes the preparation by each facility to respond to an oil spill at that location. For larger spills, however, management of the response will rest with corporate regional response teams. Personnel from all departments make up the regional teams. In 1990, Congress passed the Oil Pollution Act. In 1991, the US Coast Guard began developing oil spill response contingency plan regulations, which they are still working on. Meanwhile, four of the five west coast states have also passed laws requiring contingency plans. (Only Hawaii has chosen to wait and see what the federal regulations will entail). Three of the states have already adopted regulations. Given these laws and regulations, along with its corporate structure, Texaco addressed the need to standardize local facility plans as well as its response organization. This paper discusses how, by working together, the Texaco corporate international oil spill response staff and the Texaco western region on-scene commander developed: A standard contingency plan format crossing corporate boundaries and meeting federal and state requirements. A response organization applicable to any size facility or spill. A strategy to sell the standard contingency plan and response organization to the operating units

Competitiveness in the Brazilian oil industry. The Brazilian 'oil diamond'

International Nuclear Information System (INIS)

Zamith, R.; Moutinho Dos Santos, E.

2000-01-01

It is recognized the economic benefits that might follow the opening process of the Brazilian oil and natural gas industry, which shall experience a fast expansion with the arrival of national and international private investors. However, we should not neglect the broader impact of this process on the future development of all that cluster of national agents that lived around and served the former national oil monopoly, managed by the Brazilian National Oil Company, Petrobras. This work focuses on this larger perspective, discussing about the capacity of Brazil to sustain and expand its competitiveness in the oil business as well as to obtain the maximum economic development from the exploration of its oil and gas reserves. We adopt the work of Michael Porter, from the University of Harvard, about the Competitive Advantage of Nations, as a theoretical model to analyze the Competitive Advantage of Brazil in the global oil industry. By introducing the concept of ''oil diamond'', adapted from the notion introduced by this author, we develop a new understanding of national competitiveness in the oil sector. In this paper, we present the general model as well as a brief characterization of the results found for Brazil Subsequently, we focus on just one leg of the model, for which we discuss, with more detail, about the competitive condition of the country in the opening-up scenario. This leg regards the so-called supporting and supplementary industries that constitute what is denominated in the French tradition the ''para petroleum'' industry. We analyze the conditions for the Brazilian domestic ''para petroleum industry'' to survive and grow in the new competitive environment. (authors)

Essays on oil and the macroeconomy

Energy Technology Data Exchange (ETDEWEB)

Melolinna, M.

2012-07-01

This dissertation studies the effects of crude oil on the macroeconomy using a vector autoregression (VAR) modelling framework. In particular, the importance of identifying different types of oil shocks is explored for both small and large open economies. A VAR model is also used to study the information content of oil futures contracts. The dissertation consists of three essays. The first essay of the dissertation introduces a methodology for identifying oil supply shocks in a small open economy. Financial market information is used to construct an identification scheme that forces the response to an oil shock of the VAR model to be the same as that implied by futures markets. Due to the identification scheme, the model is only partially identified, and confidence intervals for impulse responses are calculated by using a bootstrapping procedure. The methodology is applied in illustrative examples to two small open economies in a VAR model that includes key domestic and international macroeconomic variables. The results suggest that while oil supply shocks have had an effect on domestic inflation during recent past, the effect on domestic GDP is ambiguous. The second essay of the dissertation studies the existence of risk premiums in crude oil futures prices with simple ordinary least squares regression and Bayesian VAR models. It also studies the importance of three main theoretical risk premium models in explaining and forecasting the risk premiums in practice. Whilst the existence of the premiums and the validity of the models can be established at certain time points, it turns out that the choice of sample period has a considerable effect on the results. Hence, the risk premiums are highly time-varying. The study also establishes a model, based on speculative positions in the futures markets, which has some predictive power for future oil spot prices. The third essay of the dissertation explores oil market and other macroeconomic shocks in a structural VAR

VSAT: opening new horizons to oil and gas explorations

Science.gov (United States)

Al-Dhamen, Muhammad I.

2002-08-01

Whether exploring in the Empty Quarter, drilling offshore in the Gulf of Mexico, or monitoring gas pipelines or oil wells in the deserts, communications is a key element to the success of oil and gas operations. Secure, efficient communications is required between remote, isolated locations and head offices to report on work status, dispatch supplies and repairs, report on-site emergencies, transfer geophysical surveys and real-time drilling data. Drilling and exploration firms have traditionally used land-based terrestrial networks that rely on radio transmissions for voice and data communications to offshore platforms and remote deep desert drilling rigs. But these systems are inefficient and have proven inflexible with today's drilling and exploration communications demands, which include high-speed data access, telephone and video conferencing. In response, numerous oil and gas exploration entities working in deep waters and remote deep deserts have all tapped into what is an ideal solution for these needs: Very Small Aperture Terminal Systems (VSAT) for broadband access services. This led to the use of Satellite Communication Systems for a wide range of applications that were difficult to achieve in the past, such as real-time applications transmission of drilling data and seismic information. This paper provides a thorough analysis of opportunities for satellite technology solutions in support of oil and gas operations. Technologies, architecture, service, networking and application developments are discussed based upon real field experience. More specifically, the report addresses: VSAT Opportunities for the Oil and Gas Operations, Corporate Satellite Business Model Findings, Satellite Market Forecasts

First refinery opened in Kyrgyz Republic

International Nuclear Information System (INIS)

Anon.

1996-01-01

The first oil refinery in the Kyrgyz Republic was opened on 5 October 1996 in Jalalabad in a ceremony attended by the President of the Central Asian country, Askar Akaev. The 10,000 barrels of oil per day (bopd) modular refinery has been financed by the Canadian oil junior, Kyrgoil Corporation, which has also formed a joint venture with the national oil company, Kyrgyzneft, to redevelop where viable the 628 underperforming oil wells in the Kyrgyz Republic sector of the Fergana Basin. The opening is the first significant milestone in a programme initiated by Akaev to develop the oil production industry in the Kyrgyz Republic. Currently the country imports more than 50,000 barrels of oil equivalent per day, mostly from Kazakhstan. In the year ending March 1996, 110 million was spent on imports of fuel products, an amount that exceeds the trade deficit over the same period. Built in only eight months, the Pound 12 million refinery will gradually be brought to full capacity. By January, it is expected that more than 5,000 barrels of gasoline, diesel and fuel oil will be produced every day. Although there is some crude oil in storage, the ramping of production is tied into the programme of workovers of the existing wells. There are no current plans to import crude, although most of the infrastructure is in place should it become necessary. (author)

Facility Response Plan (FRP) Inspected Points, Region 9, 2014, US EPA Region 9

Data.gov (United States)

U.S. Environmental Protection Agency — A Facility Response Plan (FRP) demonstrates a facility's preparedness to respond to a worst case oil discharge. Under the Clean Water Act, as amended by the Oil...

National Nanotechnology Laboratory (LNNano) open facilities for scientific community: new methods for polymeric materials characterization

International Nuclear Information System (INIS)

Silva, Cristiane A.; Santos, Ramon H.Z. dos; Bernardes, Juliana S.; Gouveia, Rubia F.

2015-01-01

National Nanotechnology Laboratory (LNNano) at the National Center for Energy and Materials (CNPEM) presents open facilities for scientific public in some areas. In this work will be discussed the facilities for mainly the polymeric community, as well as new methods for the characterization. Low density polyethylene (LDPE) surfaces were characterized by X-ray microtomography and X-ray photoelectron spectroscopy (XPS). The results obtained by microtomography have shown that these surfaces present different contrasts when compared with the bulk. These differences are correlated with the formation of an oxidized layer at the polymer surface, which consequently have a greater X-ray attenuation. This hypothesis is confirmed by XPS, which shows LDPE surface layers are richer in carbonyl, carboxyl and vinyl groups than the bulk. This work presents that microtomography can be used as a new method for detection and characterization of polymer surface oxidation. (author)

Incinerators, Hazardous Waste, To identify and locate abandoned oil production facilities and apparatus which pose a potential threat for creating an oil spill through either natural or accidental causes., Published in 1998, 1:24000 (1in=2000ft) scale, Louisiana State University (LSU).

Data.gov (United States)

NSGIC Education | GIS Inventory — Incinerators, Hazardous Waste dataset current as of 1998. To identify and locate abandoned oil production facilities and apparatus which pose a potential threat for...

25 CFR 226.38 - Measuring and storing oil.

Science.gov (United States)

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Measuring and storing oil. 226.38 Section 226.38 Indians... LANDS FOR OIL AND GAS MINING Requirements of Lessees § 226.38 Measuring and storing oil. All production.... Facilities suitable for containing and measuring accurately all crude oil produced from the wells shall be...

Open fireplace furnace as an adequate heating system

Energy Technology Data Exchange (ETDEWEB)

Terbrack, E.

The fireplace furnace is a furnace for the open fireplace. It is connected to the existing fuel-oil or gas central heating and is used for house heating and warm water preparation when the fire in the fireplace is on. It combines the romanticism of the open fireplace with the necessity of saving fuel oil and gas, ensuring heat supply.

North Sea oil and gas: a geographical perspective

Energy Technology Data Exchange (ETDEWEB)

Chapman, K

1976-01-01

Only ten years after the first rig moved into position, British oil has been piped ashore from the North Sea and, by 1980, will be making a substantial contribution to UK energy supplies. The discovery of natural gas in 1967--for initially gas was the primary objective--has transformed the gas supply so that 90% of the UK's needs already come from the North Sea. The speed and concentration of exploration pinpoints the vital importance of this new energy source. Until now the major oil 'pipeline' in the world has been led between the Middle East and Western Europe, so this new energy source has far reaching implications, both political and economic. Keith Chapman examines these implications starting from events in the North Sea itself; the geological background, agreement on the division of the North Sea, relations between oil companies, and government embodied in offshore mining legislation. The latter part of the book concentrates on the onshore repercussions of offshore activities; how North Sea oil fits into the international oil system, the various options open for its utilisation, the attitude of the EEC towards Scottish-based resources, government policy for the North coast of Scotland--an area which planners classed as ''peripheral'' but which must now accommodate extensive support facilities and service industries for the oil sites. There is also the question of relations between national and commercial interests--government versus the giant multi-national companies which took the initial gamble in the North Sea and are now responsible for the development of a resource vital to the economic well-being of Western Europe.

Environmental and economic assessment of discharges from Gulf of Mexico region oil and gas operations

International Nuclear Information System (INIS)

Gettleson, D.A.

1993-01-01

Continental Shelf Associates, Inc. (CSA) was contracted to conduct a three-year study of the environmental and health related impacts of produced water and sand discharges from oil and gas operations. Data on naturally occurring radioactive materials (NORM), heavy metals, and hydrocarbons in water, sediment, and biota will be collected and evaluated. Health related impacts will be studied through field collections and analyses of commercially- and recreationally-important fish and shellfish tissues. Additionally, information on seafood catch, consumption, and use patterns for the Gulf of Mexico will be gathered and analyzed. The facilities to be studied will include both offshore and coastal facilities in the Gulf of Mexico. Coastal sites will be additionally studied to determine ecological recovery of impacted wetland and open bay areas. The economic impact of existing and proposed effluent federal and state regulations will also be evaluated. The primary objectives of the project are to increase the base of scientific knowledge concerning (1) the fate and environmental effects of organics, trace metals, and NORM in water, sediment, and biota near several offshore oil and gas facilities; (2) the characteristics of produced water and produced sand discharges as they pertain to organics, trace metals, and NORM variably found in association with the discharges; (3) the recovery of four terminated produced water discharge sites located in wetland and high-energy open bay sites of coastal Louisiana and Texas; (4) the economic and energy supply impacts of existing and anticipated federal and state offshore and coastal discharge regulations; and (5) the catch, consumption and human use patterns of seafood species collected from coastal and offshore waters. Accomplishments for this period are described

Oil removal of spent hydrotreating catalyst CoMo/Al{sub 2}O{sub 3} via a facile method with enhanced metal recovery

Energy Technology Data Exchange (ETDEWEB)

Yang, Yue [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Xu, Shengming, E-mail: smxu@tsinghua.edu.cn [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Beijing Key Lab of Radioactive Wastes Treatment, Tsinghua University, Beijing 100084 (China); Li, Zhen [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Wang, Jianlong [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Beijing Key Lab of Radioactive Wastes Treatment, Tsinghua University, Beijing 100084 (China); Zhao, Zhongwei [School of Metallurgy and Environment, Central South University, Changsha 410083, Hunan (China); Xu, Zhenghe, E-mail: zhenghe.xu@ualberta.ca [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Department of Chemical and Material Engineering, University of Alberta, Edmonton, Alberta T6G 1H9 (Canada)

2016-11-15

Highlights: • A novel approach for oil removal from spent hydrotreating catalysts has been developed. • Oil removal possibility is analyzed through surface characteristics. • Oil is successfully removed from spent catalysts via aqueous surfactant solution. • Over 98% Mo can be leached after oil removal and thermal treatment. • The proposed deoiling method helps to avoid detrimental impurity generation (CoMoO{sub 4}) and enhance metal recovery. - Abstract: Deoiling process is a key issue for recovering metal values from spent hydrotreating catalysts. The oils can be removed with organic solvents, but the industrialized application of this method is greatly hampered by the high cost and complex processes. Despite the roasting method is simple and low-cost, it generates hardest-to-recycle impurities (CoMoO{sub 4} or NiMoO{sub 4}) and enormous toxic gases. In this study, a novel and facile approach to remove oils from the spent hydrotreating catalysts is developed. Firstly, surface properties of spent catalysts are characterized to reveal the possibility of oil removal. And then, oils are removed with water solution under the conditions of 90 °C, 0.1 wt% SDS, 2.0 wt% NaOH and 10 ml/g L/S ratio for 4 h. Finally, thermal treatment and leaching tests are carried out to further explore the advantages of oil removal. The results show that no hardest-to-recycle impurity CoMoO{sub 4} is found in XPS spectra of thermally treated samples after deoiling and molybdenum is leached completely with sodium carbonate solution. It means that the proposed deoiling method can not only remove oils simply and without enormous harmful gases generating, but also avoid the generation of detrimental impurity and promote recycling of valuable metals from spent hydrotreating catalysts.

Thermal performance analysis of Brayton cycle with waste heat recovery boiler for diesel engines of offshore oil production facilities

International Nuclear Information System (INIS)

Liu, Xianglong; Gong, Guangcai; Wu, Yi; Li, Hangxin

2016-01-01

Highlights: • Comparison of Brayton cycle with WHRB adopted in diesel engines with and without fans by thermal performance. • Waste heat recovery technology for FPSO. • The thermoeconomic analysis for the heat recovery for FPSO. - Abstract: This paper presents the theoretical analysis and on-site testing on the thermal performance of the waste heat recovery system for offshore oil production facilities, including the components of diesel engines, thermal boilers and waste heat boilers. We use the ideal air standard Brayton cycle to analyse the thermal performance. In comparison with the traditional design, the fans at the engine outlet of the waste heat recovery boiler is removed due to the limited space of the offshore platform. The cases with fan and without fan are compared in terms of thermal dynamics performance, energy efficiency and thermo-economic index of the system. The results show that the application of the WHRB increases the energy efficiency of the whole system, but increases the flow resistance in the duct. It is proved that as the waste heat recovery boiler takes the place of the thermal boiler, the energy efficiency of whole system without fan is slightly reduced but heat recovery efficiency is improved. This research provides an important guidance to improve the waste heat recovery for offshore oil production facilities.

The macroeconomic effects of oil price fluctuations on a small open oil-producing country. The case of Trinidad and Tobago

International Nuclear Information System (INIS)

Lorde, Troy; Thomas, Chrystol; Jackman, Mahalia

2009-01-01

Using vector autoregressive (VAR) methodology, this paper empirically investigates the macroeconomic effects of oil price fluctuations on Trinidad and Tobago. Overall, we find that the price of oil is a major determinant of economic activity of the country. Our impulse response functions suggest that following a positive oil price shock, output falls within the first two years followed by positive and growing response. We also investigate the macroeconomic impact of oil price volatility. Results suggest that an unanticipated shock to oil price volatility brings about random swings in the macroeconomy; however, only government revenue and the price level exhibit significant responses. With regard to the magnitude of the responses, shocks to oil price volatility tend to yield smaller macroeconomic impacts in comparison to shocks to oil prices. Variance decompositions suggest that the price of oil is a major component of forecast variation for most macroeconomic variables. Finally, Granger-causality tests indicate causality from oil prices to output and oil prices to government revenue. (author)

Evaluation of energy efficiency options in steam assisted gravity drainage oil sands surface facilities via process integration

International Nuclear Information System (INIS)

Carreon, Carlos E.; Mahmoudkhani, Maryam; Alva-Argaez, Alberto; Bergerson, Joule

2015-01-01

While new technologies are being developed for extracting unconventional oil, in the near term economic benefits and footprint reduction can be achieved by enhancing the energy efficiency of existing facilities. The objective of this work is to evaluate energy efficiency opportunities for in situ extraction of Canada's oil sands resource using pinch analysis. Modifications to an original plant design are analyzed in order to estimate utility savings beyond those obtained for the initial process configuration. The modifications explored in this paper are estimated to deliver energy savings of up to 6% beyond ‘business as usual’. This corresponds to GHG emissions reduction of approximately 5%. However, in some cases, this increase in energy savings comes at the cost of increasing demand for make-up water and volume of disposal water. Surplus generation of steam beyond heating requirements in the water treatment system leads to energy inefficiencies. Additional cost and energy savings are obtained by reducing or eliminating the use of glycol in the cooling circuit. - Highlights: • Pinch analysis performed for unconventional oil recovery process to identify inefficiencies. • Both the removal of pinch violations and process modifications lead to savings. • Effect of energy savings on water consumption for the process is considered. • Greenhouse gas emissions reduction and economic benefit are estimated for the studied cases

APPLICATION OF STANDARDIZED QUALITY CONTROL PROCEDURES TO OPEN-PATH FOURIER TRANSFORM INFRARED DATA COLLECTED AT A CONCENTRATED SWINE PRODUCTION FACILITY

Science.gov (United States)

Open-path Fourier transform infrared (OP/FT-IR) spectrometry was used to measure the concentrations of ammonia, methane, and other atmospheric eases at a concentrated swine production facility. A total of 2200 OP/FT-IR spectra were acquired along nine different monitoring paths d...

Subsurface Facility System Description Document

International Nuclear Information System (INIS)

Eric Loros

2001-01-01

The Subsurface Facility System encompasses the location, arrangement, size, and spacing of the underground openings. This subsurface system includes accesses, alcoves, and drifts. This system provides access to the underground, provides for the emplacement of waste packages, provides openings to allow safe and secure work conditions, and interfaces with the natural barrier. This system includes what is now the Exploratory Studies Facility. The Subsurface Facility System physical location and general arrangement help support the long-term waste isolation objectives of the repository. The Subsurface Facility System locates the repository openings away from main traces of major faults, away from exposure to erosion, above the probable maximum flood elevation, and above the water table. The general arrangement, size, and spacing of the emplacement drifts support disposal of the entire inventory of waste packages based on the emplacement strategy. The Subsurface Facility System provides access ramps to safely facilitate development and emplacement operations. The Subsurface Facility System supports the development and emplacement operations by providing subsurface space for such systems as ventilation, utilities, safety, monitoring, and transportation

Heavy Oil Recovery Ohmsett Test Report

Science.gov (United States)

2012-06-01

U.S. The first phase of separation is to refloat the oil for physical collection using a conveyor belt or rope mop oil skimmer. The open discharge is...inverted cone-shroud installed in the Frac tank for physical collection using a conveyor belt or rope mop oil skimmer. Heavy Oil Recovery Ohmsett Test...develop and test viable designs for systems which can detect and recover oil from subsurface environments. This is the second major report within this

The development of today's mineable oil sands projects, the key factors influencing economics

International Nuclear Information System (INIS)

Lynn, J.R.

1991-01-01

Many factors influence the perception of economic performance for developing projects. Some of these factors can be controlled by the developer, while some are outside the developer's sphere of influence. Technology selection, management systems, stakeholder involvement, environmental responsiveness and risk management are areas that may be influenced, however interest rates, product prices and currency exchange all have a measurable effect on project economics and are beyond a developer's control. Economic considerations for evaluating mineable oil sand development projects are outlined, focussing on the key factors unique to such developments in general and to the OSLO project in particular. The OSLO project is a proposed $5 billion energy development that entails constructing an open pit oil sands mine and a bitumen extraction facility north of Fort McMurray, Alberta, coupled with a bitumen upgrader in the Redwater area. 7 figs

Recreating wetland ecosystems in an oil sands disturbed landscape : Suncor consolidated-tailings demonstration wetlands

Energy Technology Data Exchange (ETDEWEB)

Daly, C. [Suncor Energy, Fort McMurray, AB (Canada). Aquatic Reclamation Research; Tedder, W.; Marlowe, P. [Golder Associates Ltd., Calgary, AB (Canada). Oil Sands Div.

2009-10-01

Open pit oil sands mining involves the disturbance of thin overburden covers of Boreal forest lands that must be returned to equivalent land capability after mining activities have ceased. Before mining starts, any wetlands are drained, timber is harvested, and peat, topsoils and subsoils are stockpiled for later use. This article discussed wetland reclamation activities conducted by Suncor Energy at its open pit mining operations. Research facilities were constructed in order to determine if wetlands constructed with consolidated tailings (CT) and pond effluent water (PEW) were able to support a sustainable vegetation community. Thirty-three cat-tail plots were established at the facility as well as unplanted plots in order to determine how quickly natural establishment occurred. Shoreline plug transplants and transplants from a natural saline lake were also introduced. Within 5 years, over 23 plant species had naturally colonized the CT wetlands. However, diversity was lower in CT and PEW-constructed wetlands. It was concluded that the application of a native peat-mineral mix soil may help to increase plant diversity. 20 refs., 5 figs.

15th International Sunflower Conference Synthesis of new derivatives from vegetable sunflower oil methyl esters via epoxydation and oxirane opening

Directory of Open Access Journals (Sweden)

Pages Xavier

2001-03-01

Full Text Available Recently, epoxides have received increased attention because they are of interest both as end-products and as chemical intermediates; epoxidized oils, mainly High Oleic Sunflower Oil, and their ester derivatives have thus found important applications as plasticizers and additives for polyvinyl chloride (PVC. Epoxidized esters have been produced classically from High Oleic Sunflower Methyl Esters (HOSME using H2O2 and formic acid. The epoxidation reaches 90% on pilot scale (5kg. Epoxidized esters produced from HOSME have respectively hydroxyl values of 0, oxirane values of 5.2/4.5 and iodine values of 1.7/1.5. Cleavage trials of the oxirane group of the epoxidized esters with different reactants have been undertaken in order to produce on pilot scale new derivatives to be characterized and tested in different fields of application (lubrication, detergency and as chemical intermediates. Reaction of Epoxy-HOSME with an excess of oleic acid was conducted under atmospheric pressure without any catalyst and solvent. The oxirane opening leads to complete estolide formation: after neutralization, analytical controls (chemical values, GC and HPLC analysis indicate that the estolides are composed of a mixture of C36 (oleate of methyl hydroxystearate and C54 (di-oleate of methyl dihydroxystearate. Oxirane opening with alcohols (ethanol and octanol was preferentially performed by acid catalysis at 100°C under atmospheric pressure. Analytical controls show the formation of different etheralcohols and secondary products resulting from dehydration, transesterification and dimerization side-reactions. Cleavage reaction of Epoxy-HOSME with a primary amine (butylamine was conducted under pressure, at high temperature (180/200°C. Both transesterification and opening of the oxirane group occur under these conditions. Reaction products are composed of amides formed by transesterification and a mixture of fatty amines/imines obtained by ring opening as established

Electricity/oil substitution

International Nuclear Information System (INIS)

Melvin, J.G.

1980-09-01

The extent to which electricity could substitute for imported oil in Canada is assessed and it is concluded that the bulk of projected oil imports could be displaced. This substitution of electricity for oil could be largely completed within two decades, with existing technology, using Canadian resources. The substitution of electricity for imported oil would result in relatively low energy costs and would stimulate economic growth. Energy self-sufficiency through the substitution of electricity for oil is uniquely a Canadian option; it is not open to other industrial countries. The option exists because of Canada's resources of oil sands for essential liquid fuels, hydraulic and nuclear electrical potential, and natural gas as an interim source of energy. While other countries face an energy crisis due to declining supplies of oil, Canada faces opportunities. The policies of Federal and Provincial governments, as perceived by individual decision makers, will have a major influence on Canada's ability to realize opportunities. (auth)

Mitigation of Oil in Water Column: Mitigation Prototype Tests

Science.gov (United States)

2017-06-01

designed with an open end to allow aquatic animals to escape. After the treated foam becomes saturated with submerged oil, the net would be lifted...needed openings to allow the frame to pass through the water column without causing severe drag resistance . However, this also allows oil to flow...to the water and should only help the regions of hypoxia caused by microbial degradation of the oil. However, the proposed field set up with

Oil Slick Characterization with UAVSAR

Science.gov (United States)

Jones, C. E.; Holt, B.

2017-12-01

Although radar has long been used for mapping the spatial extent of oil slicks, its capability for characterizing oil, e.g., to discriminate thicker from thinner oil or mineral slicks from look-alikes, is far less well defined. In fact, the capability of SAR to quantify the oil-to-water ratio of emulsions within slicks on the open water was first demonstrated using UAVSAR data acquired over the 2010 Deepwater Horizon spill in the Gulf of Mexico [Minchew et al., 2012]. UAVSAR's capability was made possible by the airborne instrument's high signal-to-noise ratio, which enabled it to measure low backscatter signals from oil-smoothed water that are often near or below the noise floor of satellite SAR instruments. Since 2010, UAVSAR has been used to study oil slicks through experiments in Norway (2015) and the Gulf of Mexico. In November 2016, UAVSAR took part in a NOAA-led experiment to study remote sensing of oil slicks, which took place at the site of a persistent seep in the Gulf of Mexico. The goal was to use remote sensing to identify zones of thicker oil, which is the type of information that could direct emergency responders for more effective clean-up. The objectives of the experiment were to validate and compare different remote sensing methods' capabilities for measuring the thickness of oil within a slick on open water under environmental conditions typical of oil spills. In this presentation, we show the results from UAVSAR for determining oil thickness within a slick, and relate them to the standard method of oil slick classification, the Bonn Agreement oil appearance code used by trained observers in the field. This work was carried out in part at the Jet Propulsion Laboratory, California Institute of Technology, under contracts with the California Dept. of Water Resources and with the National Aeronautics and Space Administration.

Oil supply and oil politics: Deja Vu all over again

International Nuclear Information System (INIS)

Cleveland, Cutler J.; Kaufmann, Robert K.

2003-01-01

President Bush has identified US dependence on imported oil as an urgent energy, economic, and national security concern. The President's energy plan promotes the development of domestic resources, based on the assumption that economic incentives and the opening of frontier areas for exploration will increase domestic production. If realized, this will reduce dependence on imported oil and reduce OPEC's ability to affect aggregate oil supply and price. The evidence suggests, however, that this policy will not increase significantly US production of crude oil, will not reduce significantly OPEC's influence, and it will distort the US macroeconomy. Even if allowed, production from the Arctic National Wildlife Refuge will have a negligible impact on the world oil markets. Further subsidies to the oil industry will divert resources from other more productive investments. Conservation and energy efficiency merit greater emphasis in US energy policy given their ability to reduce the use of cost-effective and environmentally beneficial ways

Oil supply and oil politics: Deja Vu all over again

International Nuclear Information System (INIS)

Cleveland, C.J.; Kaufmann, R.K.

2003-01-01

President Bush has identified US dependence on imported oil as an urgent energy, economic, and national security concern. The President's energy plan promotes the development of domestic resources, based on the assumption that economic incentives and the opening of frontier areas for exploration will increase domestic production. If realized, this will reduce dependence on imported oil and reduce OPEC's ability to affect aggregate oil supply and price. The evidence suggests, however, that this policy will not increase significantly US production of crude oil, will not reduce significantly OPEC's influence, and it will distort the US macroeconomy. Even if allowed, production from the Arctic National Wildlife Refuge will have a negligible impact on the world oil markets. Further subsidies to the oil industry will divert resources from other more productive investments. Conservation and energy efficiency merit greater emphasis in US energy policy given their ability to reduce the use of cost-effective and environmentally beneficial ways. (author)

Implementing an Open Source Electronic Health Record System in Kenyan Health Care Facilities: Case Study.

Science.gov (United States)

Muinga, Naomi; Magare, Steve; Monda, Jonathan; Kamau, Onesmus; Houston, Stuart; Fraser, Hamish; Powell, John; English, Mike; Paton, Chris

2018-04-18

The Kenyan government, working with international partners and local organizations, has developed an eHealth strategy, specified standards, and guidelines for electronic health record adoption in public hospitals and implemented two major health information technology projects: District Health Information Software Version 2, for collating national health care indicators and a rollout of the KenyaEMR and International Quality Care Health Management Information Systems, for managing 600 HIV clinics across the country. Following these projects, a modified version of the Open Medical Record System electronic health record was specified and developed to fulfill the clinical and administrative requirements of health care facilities operated by devolved counties in Kenya and to automate the process of collating health care indicators and entering them into the District Health Information Software Version 2 system. We aimed to present a descriptive case study of the implementation of an open source electronic health record system in public health care facilities in Kenya. We conducted a landscape review of existing literature concerning eHealth policies and electronic health record development in Kenya. Following initial discussions with the Ministry of Health, the World Health Organization, and implementing partners, we conducted a series of visits to implementing sites to conduct semistructured individual interviews and group discussions with stakeholders to produce a historical case study of the implementation. This case study describes how consultants based in Kenya, working with developers in India and project stakeholders, implemented the new system into several public hospitals in a county in rural Kenya. The implementation process included upgrading the hospital information technology infrastructure, training users, and attempting to garner administrative and clinical buy-in for adoption of the system. The initial deployment was ultimately scaled back due to a

Approach to the open advanced facilities initiative for innovation (strategic use by industry) at the University of Tsukuba, Tandem Accelerator Complex

International Nuclear Information System (INIS)

Sasa, K.; Tagishi, Y.; Naramoto, H.; Kudo, H.; Kita, E.

2010-01-01

The University of Tsukuba, Tandem Accelerator Complex (UTTAC) possesses the 12UD Pelletron tandem accelerator and the 1 MV Tandetron accelerator for University's inter-department education research. We have actively advanced collaborative researches with other research institutes and industrial users. Since the Open Advanced Facilities Initiative for Innovation by the Ministry of Education, Culture, Sports, Science and Technology started in 2007, 12 industrial experiments have been carried out at the UTTAC. This report describes efforts by University's accelerator facility to get industrial users. (author)

Comparisons Between Asphaltenes from the Dead and Live-Oil Samples of the Same Crude Oils

DEFF Research Database (Denmark)

Aquino-Olivos, M.A.; Andersen, Simon Ivar; Lira-Galeana, C.

2003-01-01

extracted and analyzed. These pressure-driven asphaltenes found on the filter were found to make up in the range between 50 and 100 ppm of the whole crude oil. Opening of the cell did not reveal asphaltenes retained due to wall adhesion. Size exclusion chromatography tests performed on both the live......-oil-derived asphaltenes and the standard asphaltenes as precipitated by atmospheric titration on the same crude oil, revealed that the live-oil asphaltenes had apparent smaller hydrodynamic volume and narrower distributions than the standard asphaltenes for two oils. Further FTIR tests also showed large differences...

Sleeving-back of horizontal wells to control downstream oil saturation and improve oil recovery

Energy Technology Data Exchange (ETDEWEB)

Greaves, M.; Saghr, A. M. [Bath Univ (United Kingdom)

1998-12-31

Air injection has become popular as an enhanced recovery technology, applicable over a wide variety of reservoir conditions including heavy, medium and light oils. One problem observed in light oil reservoirs is the tendency to desaturate the oil layer downstream of the moving front. This is particularly common in the case of thermal recovery processes. In this experiment designed to study ways to restrict the de-saturation of the oil layer, a modified horizontal producer well, incorporating a `sleeve-back` principal was used. The objective was to replicate the `toe-to-heel` displacement process occurring during heavy oil recovery, wherein downstream oil is essentially immobile due to its high viscosity. The `sleeve-back` of the well was achieved using a co-aligned, two-well assembly, so that the upstream section of the horizontal producer well was active, and continuously adjusted during propagation of the combustion front. The use of this continuous `sleeve-back` operation to control the level of de-saturation in the downstream section of a sand pack was successful as confirmed by the very high oil recovery achieved, equivalent to 93.5 per cent of oil in place. The level of CO{sub 2} production was also very high. The `sleeve-back` of the horizontal producer well made the light oil in-situ combustion more efficient compared to what would be expected in a fully-open well. The `sleeve-back` of the well also produced thermal contours in the sand pack that closely resembled those observed with heavy, highly viscous oil. By sealing-off the otherwise open well in the downstream part of the reservoir, the de-saturation of the oil layer was prevented. 9 refs., 4 tabs., 9 figs.

40 CFR 279.30 - Do-it-yourselfer used oil collection centers.

Science.gov (United States)

2010-07-01

... WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil Collection Centers and... collection center is any site or facility that accepts/aggregates and stores used oil collected only from...

Venezuela opens up to explorers

International Nuclear Information System (INIS)

Kielmas, M.

1995-01-01

The opening of Venezuela's first exploration bidding round since oil nationalisation in 1976 was a turning-point in the country's energy policy. The state oil company, Petroleos de Venezuela (PdVSA), has said that the bidding round could generate investment of some $11 billion eventually in development investment and that over the next 10 years, nearly 20 percent of a planned $55 billion, 10-year state oil company investment programme could also come from foreign or private sector oil investment. Should this optimistic prediction materialise, Venezuela, whose 2.75 million b/d oil production in October was some 400,000 b/d over its Opec quota, will remain both the dominant oil producer in Latin America and the top-ranking oil exporter to the US market. In May this year, Venezuelan oil exports topped 1.43 million b/d, or some 16.8 percent of the US market, compared with Saudi Arabia's 15.7 percent. (author)

St. James marine terminal facility description

Energy Technology Data Exchange (ETDEWEB)

1993-10-01

The US Department of Energy (DOE) currently owns and operates a marine terminal on the west bank of the Mississippi River at St. James, Louisiana. The St. James facility was constructed by the Department to provide marine services associated with the fill and drawdown of the Strategic Petroleum Reserve (SPR) crude oil storage facilities located at Bayou Choctaw and Weeks Island, Louisiana. Although strategic to the mission of the SPR in the event of a national emergency, the St. James terminal is situated such that it has a high potential to also serve the commercial industry`s needs for crude oil terminalling and storage. The St. James terminal is located approximately 45 miles west of New Orleans and 30 miles southeast of Baton Rouge, and approximately 160 miles upstream from the mouth of the Mississippi River. Construction of the St. James terminal was initiated in 1978 and was completed in 1980. Since then, the terminal has received and transferred over 125 million barrels of crude oil to the SPR sites for storage. For crude oil distribution, the St. James terminal was connected to the neighboring LOCAP terminal by a 0.1 mile 36-inch pipeline in 1981 and to the Capline terminal by a 0.5 mile 30-inch pipeline in 1988. The terminal also has a 30-inch pipeline connection to the Koch oil terminal which was used for initial fill purposes; however, this pipeline has been disconnected and is currently inactive. A complete description of the St. James terminal facilities, operational capabilities, operational certifications, and future Government requirements are presented in Sections 2, 3, 4, and 5 respectively.

Efficiency Evaluation of Offshore Deoiling Applications utilizing Real-Time Oil-in-Water Monitors

DEFF Research Database (Denmark)

Hansen, Dennis Severin; Bram, Mads Valentin; Løhndorf, Petar Durdevic

2017-01-01

An increasing water to oil ration in the North Sea oil and gas production motivates for an optimization of the current deoiling facilities. Current facilities are operated on matured methodologies, which in most cases fulfill the government regulations. However, it has also observed...

China's oil use, 1990-2008

International Nuclear Information System (INIS)

Leung, Guy C.K.

2010-01-01

Over the past two decades, China's oil demand has risen steeply. In 1990, it was only about 25% higher than that of 1978, the year economic reform was introduced. By 2008, it had reached 396.0 million tons, roughly four times the 1978 level, making China the second largest oil user worldwide. The country became a net oil importer in 1993, and between 1993 and 2008, its net import dependency - a yardstick for energy security - soared from 7.5% to 50.0%. China's increased demand for oil has made the country a global energy player of critical importance. Although the literature on the global implications of China's oil use has proliferated, relatively few studies have attempted to examine ''how China uses oil.'' Hence, this study covers every oil-consuming facility and sector in China, exploring the patterns of, and factors involved in, oil demand by power plants, oil refineries, heat plants and, gas-works, and industrial, transport, agricultural, household and commercial sectors. It concludes that in virtually all sectors in China, oil demand will grow, with transport and industry leading the way. (author)

Carbon Capture and Sequestration from a Hydrogen Production Facility in an Oil Refinery

Energy Technology Data Exchange (ETDEWEB)

Engels, Cheryl; Williams, Bryan, Valluri, Kiranmal; Watwe, Ramchandra; Kumar, Ravi; Mehlman, Stewart

2010-06-21

The project proposed a commercial demonstration of advanced technologies that would capture and sequester CO2 emissions from an existing hydrogen production facility in an oil refinery into underground formations in combination with Enhanced Oil Recovery (EOR). The project is led by Praxair, Inc., with other project participants: BP Products North America Inc., Denbury Onshore, LLC (Denbury), and Gulf Coast Carbon Center (GCCC) at the Bureau of Economic Geology of The University of Texas at Austin. The project is located at the BP Refinery at Texas City, Texas. Praxair owns and operates a large hydrogen production facility within the refinery. As part of the project, Praxair would construct a CO2 capture and compression facility. The project aimed at demonstrating a novel vacuum pressure swing adsorption (VPSA) based technology to remove CO2 from the Steam Methane Reformers (SMR) process gas. The captured CO2 would be purified using refrigerated partial condensation separation (i.e., cold box). Denbury would purchase the CO2 from the project and inject the CO2 as part of its independent commercial EOR projects. The Gulf Coast Carbon Center at the Bureau of Economic Geology, a unit of University of Texas at Austin, would manage the research monitoring, verification and accounting (MVA) project for the sequestered CO2, in conjunction with Denbury. The sequestration and associated MVA activities would be carried out in the Hastings field at Brazoria County, TX. The project would exceed DOE?s target of capturing one million tons of CO2 per year (MTPY) by 2015. Phase 1 of the project (Project Definition) is being completed. The key objective of Phase 1 is to define the project in sufficient detail to enable an economic decision with regard to proceeding with Phase 2. This topical report summarizes the administrative, programmatic and technical accomplishments completed in Phase 1 of the project. It describes the work relative to project technical and design activities

Tea seed upgrading facilities and economic assessment of biodiesel production from tea seed oil

Energy Technology Data Exchange (ETDEWEB)

Demirbas, Ayhan [Sirnak University, Engineering Faculty, Sirnak (Turkey); Sila Science, Trabzon (Turkey)

2010-12-15

Green tea seed (Camellia sinensis L. Kuntze) oil was used in this work. The tea seed oil contains more than 84% unsaturated fatty acid, such as oleic acid (62.5% by weight), linoleic acid (18.1% by weight) and linolenic acid. The biodiesel from tea seed oil in itself is not significantly different from biodiesel produced from vegetable oils. However, tea seed oil has lower pour point and lower viscosity as different common vegetable oils. Crude tea seed oil is one of the cheapest vegetable oil feedstocks with average price, 514 (US$/ton). (author)

Tea seed upgrading facilities and economic assessment of biodiesel production from tea seed oil

International Nuclear Information System (INIS)

Demirbas, Ayhan

2010-01-01

Green tea seed (Camellia sinensisL. Kuntze) oil was used in this work. The tea seed oil contains more than 84% unsaturated fatty acid, such as oleic acid (62.5% by weight), linoleic acid (18.1% by weight) and linolenic acid. The biodiesel from tea seed oil in itself is not significantly different from biodiesel produced from vegetable oils. However, tea seed oil has lower pour point and lower viscosity as different common vegetable oils. Crude tea seed oil is one of the cheapest vegetable oil feedstocks with average price, 514 (US$/ton).

Research of losses of oil oil and mineral oil at transportation and storage

International Nuclear Information System (INIS)

Akzhigitov, A.S.

2005-01-01

Full text : All way of hydrocarbonic raw material from a mouth of oil wells up to the consumer is accompanied by losses which occur as a result of evaporation, outflow and change of quality. Therefore preservation of quantity and quality of oil and mineral oil during transportation and storages is the major not only economic, but also an ecological problem. The facilitated fractional structure, the big maintenance concern to prominent features of the majority oil from underground salts adjournment Prycaspi in them of the easy hydrocarbons, the raised gas factor in conditions of deposits and presence in structure of gases, except for hydrocarbons and sour a component, - hydrogen sulphide, carbonic gas, etc. The superficial tests stabilized on phase structure oil depending on conditions of preparation for external transport and the subsequent processing can contain this or that quantity of residual hydrogen sulphide, easy hydrocarbons and the lowest sulfhydrates. For change of temperature and external pressure, during transportation and storage the part of easy hydrocarbons and not hydrocarbonic connections (sulfur organic) can be allocated from oil in a gaseous phase and in case of hit in an atmosphere sharply worsens ecology. In the Western Kazakhstan during the years period the temperature of air sometimes reaches up to 40-45 degrees. As is known, at such temperature there is a strengthened warming up of the open surface of oil tanks, that finally leads to increase evaporation easy oil and oil hydrocarbons. With this purpose experiences by quantitative definition evaporation lungs oil and petromixes of the Western Kazakhstan were spent. As a result of the lead works it is found out, that the size of losses at the given fixed temperature depends on evaporation by nature, fractional and hydrocarbonic structures of oil

Sound Waste Management Plan environmental operations, and used oil management system: Restoration project 97115. Exxon Valdez oil spill restoration project final report: Volumes 1 and 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

This project constitutes Phase 2 of the Sound Waste Management Plan and created waste oil collection and disposal facilities, bilge water collection and disposal facilities, recycling storage, and household hazardous waste collection and storage, and household hazardous waste collection and storage facilities in Prince William Sound. A wide range of waste streams are generated within communities in the Sound including used oil generated from vehicles and vessels, and hazardous wastes generated by households. This project included the design and construction of Environmental Operations Stations buildings in Valdez, Cordova, Whittier, Chenega Bay and Tatitlek to improve the overall management of oily wastes. They will house new equipment to facilitate oily waste collection, treatment and disposal. This project also included completion of used oil management manuals.

Sound Waste Management Plan environmental operations, and used oil management system: Restoration project 97115. Exxon Valdez oil spill restoration project final report: Volumes 1 and 2

International Nuclear Information System (INIS)

1998-06-01

This project constitutes Phase 2 of the Sound Waste Management Plan and created waste oil collection and disposal facilities, bilge water collection and disposal facilities, recycling storage, and household hazardous waste collection and storage, and household hazardous waste collection and storage facilities in Prince William Sound. A wide range of waste streams are generated within communities in the Sound including used oil generated from vehicles and vessels, and hazardous wastes generated by households. This project included the design and construction of Environmental Operations Stations buildings in Valdez, Cordova, Whittier, Chenega Bay and Tatitlek to improve the overall management of oily wastes. They will house new equipment to facilitate oily waste collection, treatment and disposal. This project also included completion of used oil management manuals

The use of mesocosms in marine oil spill - ecological research and development

International Nuclear Information System (INIS)

Reilly, T.J.

1999-01-01

This paper focuses on the design of mesocosms which are partly enclosed, bounded, outdoor experimental systems for simulating marine oil spill environments for use in examining the ecological impact of the spill response. System requirements for mesocosms in marine oil spill ecological research and development are discussed, and the question of scaling, and mesocosm tank features useful in coastal/nearshore ecological marine oil spill research are considered. Details are given of the MERL mesocosm facility at the University of Rhode Island, and the Coastal Oil-Spill Simulation System (COSS) multiple tank mesocosm facility in Texas, and recommendations for the design and use of marine mesocosms in oil spill ecological impact studies are presented. (UK)

40 CFR 279.32 - Used oil aggregation points owned by the generator.

Science.gov (United States)

2010-07-01

... (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF USED OIL Standards for Used Oil... aggregation point is any site or facility that accepts, aggregates, and/or stores used oil collected only from...

China Oil and Gas Market Assessment

International Nuclear Information System (INIS)

Qiu, Yu

2004-08-01

China, with one-fifth of the world's population and one of the fastest rates of economic growth, is experiencing a boom in its energy requirements. China has been identified as a high priority market for the oil and gas sector. This priority has resulted in the high level of investment and many large-scale projects related to the oil and gas industry. Oil production from existing fields is expected to increase, new oil and gas fields will be developed, and the country's oil and gas transmission infrastructure will be extended to meet domestic demands. In addition, total domestic investment needs for the next three decades till 2030 are estimated at around $119 billion, and upstream exploration and development will account for about $69 billion. China's oil and gas exploitation business has been the biggest beneficiary of the bearish crude oil prices, national oil stockpile and the need of infrastructure. In the first six-month period of 2005, this industry has gained a profit of USD16.5 billion, up 73.4 per cent year-on-year. The country is becoming increasingly open to international oil companies, contractors and equipment suppliers, who can bring advanced technology, equipment, and management experience. In this context, considerable opportunities in the supply and service sectors are open to Dutch companies. This report analyses the present situation and market prospect of China upstream oil and gas industry, including: Current status of Chinese oil and gas industry analysis and future development forecast; Potential customers analysis, such as three stated-owned oil companies and their foreign partners;Domestic and foreign competitors analysis; Potential opportunities and challenges analysis; Providing contacts and information on main ongoing oil exploration and development projects, and business practices

A Novel Transporting System Model for Oil Refinery

OpenAIRE

Razman M. Tahar; Waleed K. Abduljabbar

2010-01-01

Problem statement: Oil refineries are widely used to store various liquids and gases. Petroleum products are in high demand. Oil companies have abundant resources of petroleum products in pipelines and storage tanks. Approach: Included are storage tanks at retail gasoline station, home heating oil tanks, lubricant storage at automotive service facilities, propane tanks in all sorts of application, and oil company terminals across the world. The aim of this study is to present a model by which...

Community Extreme Tonnage User Service (CETUS): A 5000 Ton Open Research Facility in the United States

Science.gov (United States)

Danielson, L. R.; Righter, K.; Vander Kaaden, K. E.; Rowland, R. L., II; Draper, D. S.; McCubbin, F. M.

2017-12-01

Large sample volume 5000 ton multi-anvil presses have contributed to the exploration of deep Earth and planetary interiors, synthesis of ultra-hard and other novel materials, and serve as a sample complement to pressure and temperature regimes already attainable by diamond anvil cell experiments. However, no such facility exists in the Western Hemisphere. We are establishing an open user facility for the entire research community, with the unique capability of a 5000 ton multi-anvil and deformation press, HERA (High pressure Experimental Research Apparatus), supported by a host of extant co-located experimental and analytical laboratories and research staff. We offer wide range of complementary and/or preparatory experimental options. Any required synthesis of materials or follow up experiments can be carried out controlled atmosphere furnaces, piston cylinders, multi-anvil, or experimental impact apparatus. Additionally, our division houses two machine shops that would facilitate any modification or custom work necessary for development of CETUS, one for general fabrication and one located specifically within our experimental facilities. We also have a general sample preparation laboratory, specifically for experimental samples, that allows users to quickly and easily prepare samples for ebeam analyses and more. Our focus as contract staff is on serving the scientific needs of our users and collaborators. We are seeking community expert input on multiple aspects of this facility, such as experimental assembly design, module modifications, immediate projects, and future innovation initiatives. We've built a cooperative network of 12 (and growing) collaborating institutions, including COMPRES. CETUS is a coordinated effort leveraging HERA with our extant experimental, analytical, and planetary process modelling instrumentation and expertise in order to create a comprehensive model of the origin and evolution of our solar system and beyond. We are looking to engage

The effect of oil and gas content on the controllability and separation in a de-oiling hydrocyclone

OpenAIRE

Belaidi, Hafid

2003-01-01

The effect of free gas on cyclonic oil-water separation was examined using a geometry which sought to minimise problems with gas. Tests were carried out using the purpose built oil-water separation facility at Bradford University where pre-choke conditions could be partially simulated. Firstly, tests were carried out with water and gas-water to look at flow behaviour and control parameters, then comparative tests carried out with gas-oil-water. Comparisons were also made with tests data from ...

Cryogenic aspects of the mirror fusion test facility

International Nuclear Information System (INIS)

Sterbentz, W.H.; Nelson, R.L.

1979-01-01

This paper covers the design and construction of the MFTF cryogenic system and a description of the operating procedures throughout the many functional modes. The coils and the cryopanels for maintaining the high vacuum environment weigh 417,000 kg (920,000 lb) and must be cooled from room temperature to 4.5 k. The cryogenic system for MFTF consists of a closed-loop helium system with a 3000-W helium refrigerator that uses gas-bearing expansion turbines and oil-flooded screw compressors. In addition, liquid helium storage facilities have adequate capacity for standby operation, and a complete helium-purification plant is capable of processing 17 m 3 /min (600 scfm). An open-loop liquid nitrogen system (with provision for later addition of a nitrogen recondenser) provides the required refrigeration for the radiation shields that must be maintained at 85 K

Pipeline oil fire detection with MODIS active fire products

Science.gov (United States)

Ogungbuyi, M. G.; Martinez, P.; Eckardt, F. D.

2017-12-01

We investigate 85 129 MODIS satellite active fire events from 2007 to 2015 in the Niger Delta of Nigeria. The region is the oil base for Nigerian economy and the hub of oil exploration where oil facilities (i.e. flowlines, flow stations, trunklines, oil wells and oil fields) are domiciled, and from where crude oil and refined products are transported to different Nigerian locations through a network of pipeline systems. Pipeline and other oil facilities are consistently susceptible to oil leaks due to operational or maintenance error, and by acts of deliberate sabotage of the pipeline equipment which often result in explosions and fire outbreaks. We used ground oil spill reports obtained from the National Oil Spill Detection and Response Agency (NOSDRA) database (see www.oilspillmonitor.ng) to validate MODIS satellite data. NOSDRA database shows an estimate of 10 000 spill events from 2007 - 2015. The spill events were filtered to include largest spills by volume and events occurring only in the Niger Delta (i.e. 386 spills). By projecting both MODIS fire and spill as `input vector' layers with `Points' geometry, and the Nigerian pipeline networks as `from vector' layers with `LineString' geometry in a geographical information system, we extracted the nearest MODIS events (i.e. 2192) closed to the pipelines by 1000m distance in spatial vector analysis. The extraction process that defined the nearest distance to the pipelines is based on the global practices of the Right of Way (ROW) in pipeline management that earmarked 30m strip of land to the pipeline. The KML files of the extracted fires in a Google map validated their source origin to be from oil facilities. Land cover mapping confirmed fire anomalies. The aim of the study is to propose a near-real-time monitoring of spill events along pipeline routes using 250 m spatial resolution of MODIS active fire detection sensor when such spills are accompanied by fire events in the study location.

Baseline study of methane emission from anaerobic ponds of palm oil mill effluent treatment.

Science.gov (United States)

Yacob, Shahrakbah; Ali Hassan, Mohd; Shirai, Yoshihito; Wakisaka, Minato; Subash, Sunderaj

2006-07-31

The world currently obtains its energy from the fossil fuels such as oil, natural gas and coal. However, the international crisis in the Middle East, rapid depletion of fossil fuel reserves as well as climate change have driven the world towards renewable energy sources which are abundant, untapped and environmentally friendly. Malaysia has abundant biomass resources generated from the agricultural industry particularly the large commodity, palm oil. This paper will focus on palm oil mill effluent (POME) as the source of renewable energy from the generation of methane and establish the current methane emission from the anaerobic treatment facility. The emission was measured from two anaerobic ponds in Felda Serting Palm Oil Mill for 52 weeks. The results showed that the methane content was between 35.0% and 70.0% and biogas flow rate ranged between 0.5 and 2.4 L/min/m(2). Total methane emission per anaerobic pond was 1043.1 kg/day. The total methane emission calculated from the two equations derived from relationships between methane emission and total carbon removal and POME discharged were comparable with field measurement. This study also revealed that anaerobic pond system is more efficient than open digesting tank system for POME treatment. Two main factors affecting the methane emission were mill activities and oil palm seasonal cropping.

Upstream oil and gas. Subsector no. 7: Oil and gas exploration and development 1995 to 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-08-01

Prepared by the Alberta Human Resources and Employment, this report provides a summary of the lost-time injuries and disease descriptions of workers injured while employed in the upstream oil and gas industries in Alberta during the period 1995 to 1999. The report includes the characteristics of the injured worker and the risk of injury to workers in the industries in Alberta, as well as the cost of injuries and revenue by means of total premiums paid by the employers. The occupational fatalities that were accepted by the Workers Compensation Board and investigated by the Occupational Health and Safety were summarized in the report along with a brief description of the injuries. The aim was to provide information concerning health and safety issues to government, employers, workers, and health and safety officers in the industries in Alberta about health and safety issues. The focus was placed on the oil and gas exploration and development sub-sector. Defined as all upstream oil field activities of employers which generate revenue from the production and sale of crude oil and/or natural gas, the sub-sector comprises major integrated oil and gas companies and small independent producers. In those cases where the owner/producer operates its own upstream production/processing facilities, they form an integral part of this sub-section. In addition, oil and gas marketing firms are included. Oil/gas well, well head equipment; flow lines/gathering systems tied into field processing facilities; battery sites/compressors stations; crude oil separators and natural gas dehydrators/treaters; natural gas/sulfur processing plants; heavy oil projects including steam generation; and other enhanced recovery methods are all included in the sub-sector. The other sub-sectors in the upstream oil and gas industries are: exploration, oilfield maintenance and construction, well servicing with service rigs and power swivels, drilling of oil and gas wells, oilfield downhole and other

Facile Synthesis of Flexible Methylsilsesquioxane Aerogels with Surface Modifications for Sound- Absorbance, Fast Dye Adsorption and Oil/Water Separation

Directory of Open Access Journals (Sweden)

Xingzhong Guo

2018-04-01

Full Text Available New flexible methylsilsesquioxane (MSQ aerogels have been facilely prepared by a sol–gel process with methyltrimethoxysilane (MTMS and dimethyldimethoxysilane (DMDMS as co-precursors, followed by surface modification and ambient pressure drying. The microstructure, mechanical properties and hydrophobicity of these MSQ aerogels after surface modifications of hexamethyldisiloxane (HMDSO and/or hexamethyldisilazane (HMDS were investigated in detail, and the applications of surface-modified MSQ aerogels in sound-absorbance, fast dye adsorption and oil/water separation were evaluated, respectively. The MSQ aerogels surface-modified by HMDS possess flexibility, elasticity and superhydrophobicity, and demonstrate good performance in the mentioned applications. The resultant MSQ aerogel used in sound-absorbance has high frequency (about 6 kHz acoustic absorptivity of up to 80%, benefiting from its macroporous structure and porosity of 94%, and it also possesses intermediate frequency acoustic absorptivity (about 1 kHz up to 80% owing to its elasticity. This MSQ aerogel can selectively separate oil from oil/water mixtures with high efficiency due to its superhydrophobicity and superlipophilicity, resulting from a lot of methyl groups, density as low as 0.12 cm3·g−1 and a water contact angle as high as 157°. This MSQ aerogel can be assembled to be a monolithic column applied for fast dye adsorption, and shows selective adsorption for anionic dyes and removal efficiency of methyl orange of up to 95%.

Scope of current abandonment issues in the oil and gas industry

International Nuclear Information System (INIS)

Scott, I.F.H.

1997-01-01

Abandonment issues in the oil and gas industry, such as well sites, batteries, gas plants, compressor stations, and pipelines, were discussed. Responsibilities of the Canadian Association of Petroleum Producers (CAPP) for informing the Canadian public about energy and environmental issues on behalf of the upstream petroleum industry were reviewed. Industry regulators and those who have jurisdiction over the abandonment of facilities were identified. In Alberta, the main agencies are the Alberta Energy and Utilities Board, Alberta Environmental Protection, and Alberta Food and Rural Development in addition to the National Energy Board and Indian Oil and Gas Canada. At the end of 1995, 160,000 wells had been drilled in Alberta of which 60,000 are still active, 35,000 are suspended and 70,000 wells have been abandoned. The industry-financed Orphan Well Program was established to provide funds for facility abandonment, decontamination and surface reclamation costs associated with orphaned facilities. CAPP agrees that operators of oil and gas facilities must be held responsible and accountable for the abandonment of their facilities. CAPP is looking for support from government to ensure that enforcement actions limit the number of orphan facilities. tabs., figs

Oil and Gas Emergency Policy: Germany 2012 update

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

Germany has very little domestic oil and natural gas production and relies heavily on imports. It has well diversified and flexible oil and natural gas supply infrastructure, which consists of crude, product and gas pipelines and crude and oil product import terminals. Natural gas is imported into Germany exclusively by cross-border pipeline. The country has no LNG infrastructure, although some German companies have booked capacities in overseas LNG terminals. Oil continues to be the main source of energy in Germany although it has declined markedly since the early 1970s. It now represents approximately 32% of Germany’s total primary energy supply (TPES). Natural gas consumption in Germany has declined 10% since 2006. Demand was 90 bcm in 2010, down from 100 bcm in 2005. According to government commissioned analysis, the total consumption of natural gas in Germany is expected to continue to decline over the long term. The share of natural gas in Germany’s TPES is currently around 22%. German oil stock levels are generally well above the required 90-days. Total oil stock levels in Germany were equivalent to 140 days net imports in April 2012. Since 1998, the German oil stockholding agency (EBV) has been solely responsible for meeting Germany's 90-day stockholding obligation. The Oil Stockholding Act stipulates that the EBV shall constantly maintain stocks of oil and petroleum products at a level equivalent to or above 90 days of net imports. There is no minimum stockholding obligation on industry, so industry held commercial stocks are held in addition to the EBV stocks. There are several legal tools available to German authorities for natural gas emergency response. These include Ordinances that can be used to restrict the sale, purchase or use of goods, both in terms of quantity and time, or permit them only for certain priority purposes, to ensure that vital energy needs are met. There are no compulsory natural gas storage requirements in Germany, and no

Exploring Vietnam's oil potential

International Nuclear Information System (INIS)

Anon.

1993-01-01

A brief review is given of the oil production potential in Vietnam. Since Since 1987, the country has been open to foreign investment in offshore exploration but has suffered from a US embargo on trade and economic ties. Nevertheless some exploration has occurred and twenty production sharing contracts with international oil companies has been signed. To date most of the finds have been non-commercial but optimism remains high. (U.K.)

Marine oil spill response organizations

International Nuclear Information System (INIS)

Hendry, C.

1997-01-01

The obligations under the law relative to the prevention of marine oil spills and the type of emergency plans needed to mitigate any adverse effects caused by a marine oil spill were discussed. The organizational structure, spill response resources and operational management capabilities of Canada's newly created Response Organizations (ROs) were described. The overall range of oil spill response services that the RO provides to the domestic oil handling, oil transportation and the international shipping industries were reviewed. Amendments to the Canada Shipping Act which require that certain ships and oil handling facilities take oil spill preparedness and response measures, including having an arrangement with an RO certified by the Canadian Coast Guard, were outlined. Canadians now benefit from five ROs established to provide coast-to-coast oil spill response coverage. These include the Western Canada Marine Response Corporation, the Canadian Marine Response Management Corporation, the Great Lakes Response Corporation, the Eastern Canada Response Corporation and the Atlantic Emergency Response Team Ltd. ROs have the expertise necessary to organize and manage marine oil spill response services. They can provide equipment, personnel and operational management for the containment, recovery and cleanup of oil spilled on water

Oil and the political economy of energy

International Nuclear Information System (INIS)

Matutinovic, Igor

2009-01-01

The key issues concerning oil exploitation are still open for discussion: there is no agreement about where we presently stand in the world oil extraction curve, what is its exact shape, and how far can oil price grow before it changes irreversibly the world economy and consumer behavior. The paper proposes an alternative scenario to the Hubbert's bell-shaped model of oil exploitation, based on more realistic assumptions regarding political agendas in oil-exporting countries and consumer behavior dynamics in oil-importing countries. Under this scenario, the joint impact of markets and public policy in oil importing countries together with 'resource pragmatism' policy in oil-exporting countries allows for a less steep oil supply curve with a much fatter tail compared to the Hubbert's model.

Fabrication of an open Au/nanoporous film by water-in-oil emulsion-induced block copolymer micelles.

Science.gov (United States)

Koh, Haeng-Deog; Kang, Nam-Goo; Lee, Jae-Suk

2007-12-18

Water-in-oil (W/O) emulsion-induced micelles with narrow size distributions of approximately 140 nm were prepared by sonicating the polystyrene-b-poly(2-vinylpyridine) (PS-b-P2VP) block copolymer in the toluene/water (50:1 vol %). The ordered nanoporous block copolymer films with the hydrophilic P2VP interior and the PS matrix were distinctly fabricated by casting the resultant solution on substrates, followed by evaporating the organic solvent and water. The porous diameter was estimated to be about 70 nm. Here, we successfully prepared the open nanoporous nanocomposites, the P2VP domain decorated by Au (5+/-0.4 nm) nanoparticles based on the methodology mentioned. We anticipate that this novelty enhances the specific function of nanoporous films.

190-C Facility <90 Day Storage Pad supplemental information to the Hanford facility contingency plan

International Nuclear Information System (INIS)

Little, N.C.

1996-12-01

The 190-C Facility <90 Day Storage Pad stores waste oils primarily contaminated with lead generated while draining equipment within the building of residual lubricating oils. Waste oils are packaged and stored in fifty-five gallon drums, or other containers permitted by the Site Specific Waste Management Instruction. Bechtel Hanford, Inc. (BHI) manual BHI-EE-02, Environmental Requirements Procedures, references this document. This document is to be used to demonstrate compliance with the contingency plan requirements in Washington Administrative Code, Chapter 173-303, Dangerous Waste Regulations, for certain Resource Conservation and Recovery Act of 1976 (RCRA) waste management units (units). Refer to BHI-EE-02, for additional information

Effect of Amygdalus scoparia kernel oil consumption on lipid profile of the patients with dyslipidemia: a randomized, open-label controlled clinical trial.

Science.gov (United States)

Zibaeenezhad, Mohammad Javad; Shahamat, Maryam; Mosavat, Seyed Hamdollah; Attar, Armin; Bahramali, Ehsan

2017-10-03

Amygdalus scoparia kernel (ASK) oil is traditionally used for Hyperlipidemia. Compared to olive oil, it has higher proportion of unsaturated to saturated fatty acid besides exhibiting higher index of oxidative stability. The lipid-lowering effects of ASK oil however, has not been investigated yet. This study is the first one to evaluate such effects in patients with dyslipidemia. Serum triglyceride levels significantly decreased in the intervention compared to control group (24.80 ± 51.70 vs 3.13 ± 44.80, p -value = 0.03). Serum total cholesterol, LDL and HDL cholesterol levels did not change significantly ( p = 0.28 and p = 0.68 and p = 0.10 respectively). In a double arm, open-label, randomized controlled trial,101 hyperlipidemic patients were recruited. The designation of hyperlipidemia was upon meeting either of the three criteria: having serum low-density lipoprotein (LDL) cholesterol level 130-190 (mg/dl), serum triglyceride level 150-400 (mg/dl), and serum high-density lipoprotein (HDL) cholesterol level less than 50 (mg/dl) for women and 40 (mg/dl) for men. Patients who have ever been prescribed with an antihyperlipidemic medication were excluded. They were randomly assigned to intervention group, receiving the ASK oil, for 60 days and control group. Serum lipid measurements were repeated at the end of the intervention period. ASK oil supplementation may have a positive effect in reducing serum triglyceride level in patients with dyslipidemia without significant effect on serum cholesterol levels.

Dynamically consistent oil import tariffs

International Nuclear Information System (INIS)

Karp, L.; Newbery, D.M.

1992-01-01

The standard theory of optimal tariffs considers tariffs on perishable goods produced abroad under static conditions, in which tariffs affect prices only in that period. Oil and other exhaustable resources do not fit this model, for current tariffs affect the amount of oil imported, which will affect the remaining stock and hence its future price. The problem of choosing a dynamically consistent oil import tariff when suppliers are competitive but importers have market power is considered. The open-loop Nash tariff is solved for the standard competitive case in which the oil price is arbitraged, and it was found that the resulting tariff rises at the rate of interest. This tariff was found to have an equilibrium that in general is dynamically inconsistent. Nevertheless, it is shown that necessary and sufficient conditions exist under which the tariff satisfies the weaker condition of time consistency. A dynamically consistent tariff is obtained by assuming that all agents condition their current decisions on the remaining stock of the resource, in contrast to open-loop strategies. For the natural case in which all agents choose their actions simultaneously in each period, the dynamically consistent tariff was characterized, and found to differ markedly from the time-inconsistent open-loop tariff. It was shown that if importers do not have overwhelming market power, then the time path of the world price is insensitive to the ability to commit, as is the level of wealth achieved by the importer. 26 refs., 4 figs

Saudi Aramco: Oil to a Thirsty Market - International Cooperation Brings New Oil Field on Quickly

Energy Technology Data Exchange (ETDEWEB)

Al-Ajmi, Ali

2007-07-01

In response to high oil demand in 2004, Saudi Aramco committed to build facilities for the 500,000 BOPD Khursaniyah Oil Field in only 34 months from the start of preliminary engineering to startup. The project schedule was six months faster than any previous project, in the most resource competitive market the oil business has ever seen. The execution of this project required a new contract strategy, novel engineering and construction methods, and international cooperation from EPC firms and manufacturers. The project is also building a new one billion SCF per day gas plant receiving gas from five different sources with varying pressure and H2S content, along with huge water supply and injection facilities, oil gathering lines, and product distribution lines. To execute the project in this short time frame, a temporary construction city for 30,000 men has been constructed in the desert. This city has workers from all over 30 countries, speaking more than 15 languages, all focused on achieving one goal - on time completion of the most complex project ever done in Saudi Arabia. The paper will focus on the unique challenges of managing a city of this size that lasts for only 24 months. (auth)

Aurora oil switch upgrade program

International Nuclear Information System (INIS)

Warren, T.

1989-03-01

This report describes the short pulse synchronization requirements, the original Aurora trigger scheme, and the PI/SNLA approach to improving the synchronization. It also describes the oil switching design study undertaken as the first phase of the program. A discussion of oil-switch closure analysis and the conceptual design motivated by this analysis are presented. This paper also describes the oil-switch trigger pulser tests required to validate the concept. This includes the design of the testing facility, a description of the test goals, and a discussion of the results. This paper finally describes oil-switch trigger pulser testing on one of the four Aurora Blumlein modules, which includes the hardware design and operation, the testing goals, hardware installation, and test results. 9 refs., 26 figs

Oil price pass-through into inflation

International Nuclear Information System (INIS)

Chen, Shiu-Sheng

2009-01-01

This paper uses data from 19 industrialized countries to investigate oil price pass-through into inflation across countries and over time. A time-varying pass-through coefficient is estimated and the determinants of the recent declining effects of oil shocks on inflation are investigated. The appreciation of the domestic currency, a more active monetary policy in response to inflation, and a higher degree of trade openness are found to explain the decline in oil price pass-through. (author)

Will this open space work?

Science.gov (United States)

Vischer, J

1999-01-01

Northern Oil is moving offices, and CEO Fritz Schumacher wants to make the most of the move in this fictional case study. He believes that adopting an open-plan work space will reinvent how the company works, not to mention cut costs. Facilities manager Sasha Pasternak also supports the open plan. Her job would be easier, and her budget would stretch further, if Northern had standardized workstations and used partitions, not walls. And she likes the way the new design flattens the organization: everyone has the same amount of space and the same ergonomically sound furniture. The new building would have more conference rooms and just-in-time work spaces for employees who worked mostly off-site. And although she knew that initial meetings between the architects and Northern employees hadn't yielded much support for open space--people were attached to their private offices--she expected that people would warm to the idea. But when the new design was unveiled, employees were less than enthusiastic. They hurled questions like, How will workers concentrate if they can't shut their office doors? How will people have confidential meetings with their boss? And why would people stay at Northern when the competition offers them private offices? There was even talk of circulating a petition refusing to move to the new space. A week later, the architect presented revised plans to the project group. The new options would add costs and reduce the amount of space savings, but offering a choice to employees might make them feel less threatened. What should the project team do? Five commentators offer advice.

Guide to research facilities

Energy Technology Data Exchange (ETDEWEB)

1993-06-01

This Guide provides information on facilities at US Department of Energy (DOE) and other government laboratories that focus on research and development of energy efficiency and renewable energy technologies. These laboratories have opened these facilities to outside users within the scientific community to encourage cooperation between the laboratories and the private sector. The Guide features two types of facilities: designated user facilities and other research facilities. Designated user facilities are one-of-a-kind DOE facilities that are staffed by personnel with unparalleled expertise and that contain sophisticated equipment. Other research facilities are facilities at DOE and other government laboratories that provide sophisticated equipment, testing areas, or processes that may not be available at private facilities. Each facility listing includes the name and phone number of someone you can call for more information.

Oil and the political economy of energy

Energy Technology Data Exchange (ETDEWEB)

Matutinovic, Igor [GfK-Center for Market Research, Zagreb (Croatia)

2009-11-15

The key issues concerning oil exploitation are still open for discussion: there is no agreement about where we presently stand in the world oil extraction curve, what is its exact shape, and how far can oil price grow before it changes irreversibly the world economy and consumer behavior. The paper proposes an alternative scenario to the Hubbert's bell-shaped model of oil exploitation, based on more realistic assumptions regarding political agendas in oil-exporting countries and consumer behavior dynamics in oil-importing countries. Under this scenario, the joint impact of markets and public policy in oil importing countries together with 'resource pragmatism' policy in oil-exporting countries allows for a less steep oil supply curve with a much fatter tail compared to the Hubbert's model. (author)

The oiling of ICS

International Nuclear Information System (INIS)

Hunter, S.

1993-01-01

The incident command system (ICS) works for oil spills. It should be the industry standard and some will argue that it already is. But there are a number of temptations to fiddle with it. Fueling these inclinations is the fundamental difference between oil spills and natural disasters: Oil spills make the perpetrator fix the problem - under heavy oversight. Add to this difference the public outcry that attends oil spills and the dual role of government as both helper and prosecutor. From these conditions emerge adaptations of ICS which both weaken and strengthen it. The benefits of ICS are diminished by deputy incident commanders who block unified commanders from access to section chiefs, over-zealous crisis managers who displace command post decisions or its information office, separate press offices with party line slants, government law enforcement activity mixed into spill response, nonstandard operations terminology and structure involving open-quotes containment and clean upclose quotes or open-quotes salvage,close quotes and the commingling of public and private response funds. ICS's application to oil spill response is strengthened by the use of trained unified commanders, deputy incident commanders who operate as staff rather than line, crisis managers who support on-scene objectives, joint information centers, and heavy involvement of skilled, prepared environmental assessment teams in the planning section who generate priorities, strategies, and (operationally coordinated) tactics. Technically, not all these points constitute alterations of ICS, but most do and the others come close. This mixed bag of strengthening and weakening tweaks to oil spill ICS provides an opportunity to take a new look at this faithful friend to the crisis responder

Mobil Oil Canada : Kearl Oil Sands Mine

International Nuclear Information System (INIS)

1997-01-01

The upgrader design at Mobil's Kearl Oil Sands Mine were described. Included were feed characteristics, upgrader products, process schemes and their overall economics and upgrader technologies in use, including coking, deasphalting, hydrocracking, hydrotreating and visbreaking. Advantages and disadvantages of the upgrader technologies were highlighted. As far as the product is concerned, much of it is destined to U.S. refineries that are equipped to process the material. The Kearl Oil Sands Mine upgrading facility will likely use a combination of coker/hydrotreating, which is a well proven process for high value products that has been used in all five of Mobil's refineries in the U.S., and visbreaker/deasphalting, which has shown promise in bench-scale testing, but at present still has some potential commercial difficulties. Foremost among these are the high softening product of asphalt from visbroken products, questionable commercial feasibility of the low yield of pitch, and problems in the disposal of asphalt. Severe visbreaking also yields unstable products. Details of Mobil Canada's oil sands project were also summarized 2 tabs., 9 figs

Purifying oils

Energy Technology Data Exchange (ETDEWEB)

1930-04-15

Gasoline, lamp oils, and lubricating or other mineral or shale oils are refined by contacting the vapor with a hot aqueous solution of salts of zinc, cadmium, or mercury, or mixtures thereof which may contain 0-5-3-0 percent of oxide or hydroxide in solution or suspension. Chlorides, bromides, iodides, sulfates, nitrates, and sulfonates of benzol, toluol, xylol, and petroleum are specified. Washing with a solution of sodium or potassium hydroxide or carbonate of calcium hydroxide may follow. The oil may first be purified by sulfuric acid or other known agent, or afterwards caustic alkali and sulfuric acid. The Specification as open to inspection under Sect. 91 (3) (a) describes also the use of salts of copper, iron, chromium, manganese, aluminum, nickel, or cobalt, with or without their oxides or hydroxides. This subject-matter does not appear in the Specification as accepted.

Oil refining expansion criteria for Brazil

International Nuclear Information System (INIS)

Tavares, M.E.E.; Szklo, A.S.; Machado, G.V.; Schaeffer, R.; Mariano, J.B.; Sala, J.F.

2006-01-01

This paper assesses different strategies for the expansion of Brazil's oil refining segment, using criteria that range from energy security (reducing imports and vulnerability for key products) through to maximizing the profitability of this sector (boosting the output of higher value oil products) and adding value to Brazil's oil production (reducing exports of heavy acid oil). The development prospects are analyzed for conventional fuel production technology routes, sketching out three possible refining schemes for Brazilian oil and a GTL plant for producing gasoil from natural gas. Market scenario simulations indicate that investments will be required in Brazil's oil refining segment over and above those allocated to planned modifications in its current facilities, reducing the nation's vulnerability in terms of gasoil and petrochemical naphtha imports. Although not economically attractive, oil refining is a key activity that is crucial to oil company strategies. The decision to invest in this segment depends on local infrastructure conditions, environmental constraints and fuel specifications, in addition to oil company strategies, steady growth in demand and the definition of a government policy that eases institutional risks. (author)

Oil refining expansion criteria for Brazil

International Nuclear Information System (INIS)

Tavares, Marina Elisabete Espinho; Szklo, Alexandre Salem; Machado, Giovani Vitoria; Schaeffer, Roberto; Mariano, Jacqueline Barboza; Sala, Janaina Francisco

2006-01-01

This paper assesses different strategies for the expansion of Brazil's oil refining segment, using criteria that range from energy security (reducing imports and vulnerability for key products) through to maximizing the profitability of this sector (boosting the output of higher value oil products) and adding value to Brazil's oil production (reducing exports of heavy acid oil). The development prospects are analyzed for conventional fuel production technology routes, sketching out three possible refining schemes for Brazilian oil and a GTL plant for producing gasoil from natural gas. Market scenario simulations indicate that investments will be required in Brazil's oil refining segment over and above those allocated to planned modifications in its current facilities, reducing the nation's vulnerability in terms of gasoil and petrochemical naphtha imports. Although not economically attractive, oil refining is a key activity that is crucial to oil company strategies. The decision to invest in this segment depends on local infrastructure conditions, environmental constraints and fuel specifications, in addition to oil company strategies, steady growth in demand and the definition of a government policy that eases institutional risks

Comparison of Oxidation Stability and Quenchant Cooling Curve Performance of Soybean Oil and Palm Oil

Science.gov (United States)

Said, Diego; Belinato, Gabriela; Sarmiento, Gustavo S.; Otero, Rosa L. Simencio; Totten, George E.; Gastón, Analía; Canale, Lauralice C. F.

2013-07-01

The potential use of vegetable oil-derived industrial oils continues to be of great interest because vegetable oils are relatively non-toxic, biodegradable, and they are a renewable basestock alternative to petroleum oil. However, the fatty ester components containing conjugated double bonds of the triglyceride structure of vegetable oils typically produce considerably poorer thermal-oxidative stability than that achievable with petroleum basestocks under typical use conditions. Typically, these conditions involve furnace loads of hot steel (850 °C), which are rapidly immersed and cooled to bath temperatures of approximately 50-60 °C. This is especially true when a vegetable oil is held in an open tank with agitation and exposed to air at elevated temperatures for extended periods of time (months or years). This paper will describe the thermal-oxidative stability and quenching performance of soybean oil and palm oil and the resulting impact on the heat transfer coefficient. These results are compared to typical fully formulated, commercially available accelerated (fast) and an unaccelerated (slow) petroleum oil-based quenchants.

Dutch Disease in a small open economy: The case of oil in Saudi Arabia

International Nuclear Information System (INIS)

Al-Mabrouk, S.A.

1991-01-01

The effects of 'Dutch Disease' come through two channels: real wage rate and real exchange rate. A sector export boom induces both resource movement and spending effects that reinforce each other in raising higher real wage and real exchange rates. In the case of an oil boom, only the spending effect is in operation because the oil sector does not employ domestic mobile factors. After a great deal of theoretical surveying and consolidation of 'Dutch Disease' on the Saudi Arabian economy throughout the period of 1970s and 1980s. The author was trying to see whether or not the oil boom was an obstacle to economic diversification. The empirical findings support the theoretical prediction. The real exchange rate of Saudi Arabia has appreciated throughout the period of the oil-boom and, in turn, it induced an expansion in the non-traded sector and a contraction in the non-oil traded sector. The indirect effect of the oil boom came through the use of oil wealth to import technology. This effect induced further expansion in the non-traded goods at a faster rate than the non-oil traded goods

Distribution of Archaeal Communities along the Coast of the Gulf of Finland and Their Response to Oil Contamination

Science.gov (United States)

Yan, Lijuan; Yu, Dan; Hui, Nan; Naanuri, Eve; Viggor, Signe; Gafarov, Arslan; Sokolov, Sergei L.; Heinaru, Ain; Romantschuk, Martin

2018-01-01

The Baltic Sea is vulnerable to environmental changes. With the increasing shipping activities, the risk of oil spills remains high. Archaea are widely distributed in many environments. However, the distribution and the response of archaeal communities to oil contamination have rarely been investigated in brackish habitats. Hence, we conducted a survey to investigate the distribution, diversity, composition, and species interactions of indigenous archaeal communities at oil-contaminated sites along the coast of the Gulf of Finland (GoF) using high-throughput sequencing. Surface water and littoral sediment samples were collected at presumably oil-contaminated (oil distribution facilities) and clean sites along the coastline of the GoF in the winter 2015 and the summer 2016. Another three samples of open sea surface water were taken as offshore references. Of Archaea, Euryarchaeota dominated in the surface water and the littoral sediment of the coast of the GoF, followed by Crenarchaeota (including Thaumarchaeota, Thermoprotei, and Korarchaeota based on the Greengenes database used). The unclassified sequences accounted for 5.62% of the total archaeal sequences. Our study revealed a strong dependence of the archaeal community composition on environmental variables (e.g., salinity, pH, oil concentration, TOM, electrical conductivity, and total DNA concentration) in both littoral sediment and coastal water in the GoF. The composition of archaeal communities was season and ecosystem dependent. Archaea was highly diverse in the three ecosystems (littoral sediment, coastal water, and open sea water). Littoral sediment harbored the highest diversity of archaea. Oil was often detected in the littoral sediment but rarely detected in water at those presumably contaminated sites. Although the composition of archaeal community in the littoral sediment was sensitive to low-input oil contamination, the unchanged putative functional profiles and increased interconnectivity of the

Reference levels for assays in opened installations of industrial radiography

International Nuclear Information System (INIS)

Leocadio, Joao C.; Tauhata, Luiz; Crispim, Verginia R.

2001-01-01

This work had as objectives to analyze the facilities open of industrial x-ray to obtain the distribution of doses in the operators and present proposed for the reference levels. The results of the monitoring revealed an improvement of the radiation protection conditions in the facilities and that the risk of potential exposure was reduced. The advantage of the proposed reference levels is that the supervisors would enlarge the frequency of audits in the facilities opened to accomplish the investigations and interventions.The facilities open with 'bunkers' presented distributions with 95% of the doses below 0,2 mSv and the distributions of the facilities with cordoned area they had 75% of the doses below 0,4 mSv. (author)

Low-cost wave characterization modules for oil spill response

Directory of Open Access Journals (Sweden)

E.D. Skinner

2018-06-01

Full Text Available Marine oil spills can be remediated by mechanical skimmers in calm waters, but performance degrades with increased wave height. We have developed and demonstrated a system that quantifies local wave characteristics with an uncertainty of four inches of heave. Our system is intended for the measurement of wave characteristics during oil spill recovery. It conveys this information to coordinators and responders in real time via WiFi and remote reporting through a satellite network. This information will allow for enhanced situational awareness during an oil spill response, assisting stakeholders and optimizing mechanical skimming operations. Our wave characterization module (WCM uses accelerometer outputs from a very small inertial measurement unit (IMU to generate wave statistics and calculate wave characteristics. It is configured such that a WCM can either be attached to a skimmer float or incorporated into a microbuoy. Wave height and period are transmitted via WiFi and/or a satellite-enabled mesh-grid network to a cloud-hosted geographic information system (GIS. Here, we discuss the bare-bones sensors-plus-algorithm approach we developed by using spring-mass systems to approximate the wave height and period regime of interest. We then describe open water tests carried out using that development system both mounted to a weir skimmer mockup and packaged in a microbuoy. Finally, we present controlled tests in the wave tank at Ohmsett, the National Oil Spill Response Test Facility in New Jersey, with the WCMs communicating the wave characteristics via WiFi to tankside laptops and via satellite to the cloud-based GIS. Snapshot determinations of wave height calculated using the scalar magnitude of the three-axis accelerometer in the IMU were within four inches of the benchmark wave measurement system at Ohmsett. Keywords: Oil spill, Wave characterization module, Inertial measurement unit, Microbuoy

Refinery Upgrading of Hydropyrolysis Oil From Biomass

Energy Technology Data Exchange (ETDEWEB)

Roberts, Michael [Gas Technology Inst., Des Plaines, IL (United States); Marker, Terry [Gas Technology Inst., Des Plaines, IL (United States); Ortiz-Toral, Pedro [Gas Technology Inst., Des Plaines, IL (United States); Linck, Martin [Gas Technology Inst., Des Plaines, IL (United States); Felix, Larry [Gas Technology Inst., Des Plaines, IL (United States); Wangerow, Jim [Gas Technology Inst., Des Plaines, IL (United States); Swanson, Dan [Gas Technology Inst., Des Plaines, IL (United States); McLeod, Celeste [CRI Catalyst, Houston, TX (United States); Del Paggio, Alan [CRI Catalyst, Houston, TX (United States); Urade, Vikrant [CRI Catalyst, Houston, TX (United States); Rao, Madhusudhan [CRI Catalyst, Houston, TX (United States); Narasimhan, Laxmi [CRI Catalyst, Houston, TX (United States); Gephart, John [Johnson Timber, Hayward, WI (United States); Starr, Jack [Cargill, Wayzata, MN (United States); Hahn, John [Cargill, Wayzata, MN (United States); Stover, Daniel [Cargill, Wayzata, MN (United States); Parrish, Martin [Valero, San Antonio, TX (United States); Maxey, Carl [Valero, San Antonio, TX (United States); Shonnard, David [MTU, Friedrichshafen (Germany); Handler, Robert [MTU, Friedrichshafen (Germany); Fan, Jiquig [MTU, Friedrichshafen (Germany)

2015-08-31

Cellulosic and woody biomass can be converted to bio-oils containing less than 10% oxygen by a hydropyrolysis process. Hydropyrolysis is the first step in Gas Technology Institute’s (GTI) integrated Hydropyrolysis and Hydroconversion IH2®. These intermediate bio-oils can then be converted to drop-in hydrocarbon fuels using existing refinery hydrotreating equipment to make hydrocarbon blending components, which are fully compatible with existing fuels. Alternatively, cellulosic or woody biomass can directly be converted into drop-in hydrocarbon fuels containing less than 0.4% oxygen using the IH2 process located adjacent to a refinery or ethanol production facility. Many US oil refineries are actually located near biomass resources and are a logical location for a biomass to transportation fuel conversion process. The goal of this project was to work directly with an oil refinery partner, to determine the most attractive route and location for conversion of biorenewables to drop in fuels in their refinery and ethanol production network. Valero Energy Company, through its subsidiaries, has 12 US oil refineries and 11 ethanol production facilities, making them an ideal partner for this analysis. Valero is also part of a 50- 50 joint venture with Darling Ingredients called Diamond Green Diesel. Diamond Green Diesel’s production capacity is approximately 11,000 barrels per day of renewable diesel. The plant is located adjacent to Valero’s St Charles, Louisiana Refinery and converts recycled animal fats, used cooking oil, and waste corn oil into renewable diesel. This is the largest renewable diesel plant in the U.S. and has successfully operated for over 2 years For this project, 25 liters of hydropyrolysis oil from wood and 25 liters of hydropyrolysis oils from corn stover were produced. The hydropyrolysis oil produced had 4-10% oxygen. Metallurgical testing of hydropyrolysis liquids was completed by Oak Ridge National Laboratories (Oak Ridge) and showed the

Oils; gas

Energy Technology Data Exchange (ETDEWEB)

Day, D T

1922-09-18

Oils and gas are obtained from shale or oil-bearing sand by immersing the shale in and passing it through a bath of liquid oil, cracking the oil-soaked shale, and condensing the vapor and using the condensate to replenish the bath, preferably by passing the gases and vapors direct into the oil-bath container. Shale is fed continuously from a hopper to a bath of oil in an inclined chamber, is carried to the outlet by a conveyer, and through cracking tubes to an outlet pipe by conveyers. The gases and vapors escape by the pipe, a part condensing in the chamber and a run-back pipe and replenishing the bath, and the remainder passing through a condensing tower and condenser connected to reservoirs; the gas is further passed through a scrubber and a pipe to the burner of the retort. The oil condensed in the chamber overflows to the reservoir through a pipe provided with an open pipe to prevent siphoning. The conveyers and a valve on the pipe are operated by gearing. The operation may be conducted at reduced, normal, or increased pressure, e.g., 70 lbs. The temperature of the retort should be about 900 to 1400/sup 0/F, that of the inside of the tubes about 550 to 700/sup 0/F, and that of the chamber about 300/sup 0/F. The chamber and pipe may be insulated or artificially cooled.

Huff-type competitive facility location model with foresight in a discrete space

Directory of Open Access Journals (Sweden)

Milad Gorji Ashtiani

2011-01-01

Full Text Available Consider a chain as leader that wants to open p new facilities in a linear market, like metro. In this market, there is a competitor, called follower. The leader and the follower have established some facilities in advance. When the leader opens p new facilities, its competitor, follower, reacts the leader’s action and opens r new facilities. The optimal locations for leader and follower are chosen among predefined potential locations. Demand is considered as demand points and is assumed inelastic. Considering huff model, demand points are probabilistically absorbed by all facilities. The leader’s objective is maximization of its market share after opening follower’s new facilities. For solving leader problem, first the follower’s problem is solved for all leader’s potential locations and the best location for leader is obtained and then, a heuristic model is proposed for leader problem when the leader and the follower want to open one new facility. Computational results show that the proposed method is efficient for large scale problems.

Development of operation control expert system for off-site facilities

Energy Technology Data Exchange (ETDEWEB)

Takeuchi, Masaaki

1988-09-01

Concerning off-site facilities of oil refinary, changes of facilities and equipment are frequently made in order to cope flexibly with the market trends and changes of the social environment. In addition, it is desirable to introduce computerization into control and manipulation of off-site facilities for its fast, safe and sure operation. In order to achieve the above, against the existing exclusively control-oriented system, it is necessary to add the processing and generating functions to combinations between valves to be shut and piping as well as equipment to be used along the whole extent of the oil flow in the system and to add the function which makes verification of the above functions easy through a dialogue between users and the system. In order to realize the above, Cosmo Oil and Yokokawa Denki developed jointly an operation control expert system for off-site facilities and the system started its actual operation from October 1986. This article is an outline of the system. The result of its actual operation for one and a half years since its inception showed that the system was operated only by the staff responsible for the operation of the facilities, the workload was reduced to 1/3-1/4 of the workload before the adoption of the system and absolutely no omission of work nor mistake was experienced. (2 figs)

Does open access improve the process and outcome of podiatric care?

Science.gov (United States)

Wrobel, James S; Davies, Michael L; Robbins, Jeffrey M

2011-05-19

Open access to clinics is a management strategy to improve healthcare delivery. Providers are sometimes hesitant to adopt open access because of fear of increased visits for potentially trivial complaints. We hypothesized open access clinics would result in decreased wait times, increased number of podiatry visits, fewer no shows, higher rates of acute care visits, and lower minor amputation rates over control clinics without open access. This study was a national retrospective case-control study of VHA (Veterans Hospital Administration) podiatry clinics in 2008. Eight case facilities reported to have open podiatry clinic access for at least one year were identified from an email survey. Sixteen control facilities with similar structural features (e.g., full time podiatrists, health tech, residency program, reconstructive foot surgery, vascular, and orthopedic surgery) were identified in the same geographic region as the case facilities. Twenty-two percent of facilities responded to the survey. Fifty-four percent reported open access and 46% did not. There were no differences in facility or podiatry panel size, podiatry visits, or visit frequency between the cases and controls. Podiatry visits trended higher for control facilities but didn't reach statistical significance. Case facilities had more new consults seen within 30 days (96%, 89%; P = 0.050) and lower minor amputation rates (0.62/1,000, 1.0/1,000; P = 0.041). The VHA is the worlds largest managed care organization and it relies on clinical efficiencies as one mechanism to improve the quality of care. Open access clinics had more timely access for new patients and lower rates of minor amputations.

Oil production system

Energy Technology Data Exchange (ETDEWEB)

Ballantyne, J F

1983-12-21

A new oil producing system is proposed which consists of a group of underwater wells, an underwater riser and a floating storage facility for the production of the wells. The group of wells and the riser are interconnected through a manifold system in such a way that the production from any well or from the entire group of wells go to the base (foundation) of the riser. From above the riser is connected with the floating storage facility which is equipped, besides tanks for storing the well products, with a separation device for separating the oil and the accompanying gas. The gas is used as a fuel for producing electric power required by the dynamic positioning systems. The products from each well are tested by means of a regulable coupling controlled by means of a cable, which is passed from the surface through the riser. The wellhead equipment for the unslanted wells is mounted on a template previously installed on the sea floor. From the template the well products enter the riser through the manifold unit system.

Market analysis of shale oil co-products. Appendices

Energy Technology Data Exchange (ETDEWEB)

1980-12-01

Data are presented in these appendices on the marketing and economic potential for soda ash, aluminia, and nahcolite as by-products of shale oil production. Appendices 1 and 2 contain data on the estimated capital and operating cost of an oil shales/mineral co-products recovery facility. Appendix 3 contains the marketing research data.

Ex-Soviet Union: oil exporter or importer

International Nuclear Information System (INIS)

Khartukov, E.M.

1993-01-01

Perestroika of the Soviet economy and the political disintegration of the USSR have raised questions about the international ramifications of the ongoing economic and political developments in the world's largest oil-producing country. First of all, it relates to their impact on the quantity and quality of oil exports from the former Soviet Union (FSU). On the other hand, the opening of the national oil industry to foreign investors focuses their ever growing attention on the complicated internal, inter-republic oil issues which emerged after the sudden fragmentation of the Soviet oil empire into a dozen of sovereign but still interdependent parts. 1 fig., 7 tabs

Biodegradation studies of oil sludge containing high hydrocarbons concentration

International Nuclear Information System (INIS)

Olguin-Lora, P.; Munoz-Colunga, A.; Castorena-Cortes, G.; Roldan-Carrillo, T.; Quej Ake, L.; Reyes-Avila, J.; Zapata-Penasco, I.; Marin-Cruz, J.

2009-01-01

Oil industry has a significant impact on environment due to the emission of, dust, gases, waste water and solids generated during oil production all the way to basic petrochemical product manufacturing stages. the aim of this work was to evaluate the biodegradation of sludge containing high hydrocarbon concentration originated by a petroleum facility. A sludge sampling was done at the oil residuals pool (ORP) on a gas processing center. (Author)

Oil type and cross-linking influence growth of Aureobasidium melanogenum on vegetable oils as a single carbon source.

Science.gov (United States)

Peeters, Loes H M; Huinink, Hendrik P; Voogt, Benjamin; Adan, Olaf C G

2018-03-12

Aureobasidium melanogenum is the main fungus found in a spontaneously formed biofilm on a oil-treated wood. This dark colored biofilm functions as a protective coating. To better understand biofilm formation, in this study A. melanogenum was cultured on olive oil and raw linseed oil. Metabolic activity and oil conversion were measured. The results show that A. melanogenum is able to grow on linseed oil and olive oil as a single carbon source. The fungus produces the enzyme lipase to convert the oil into fatty acids and glycerol. Metabolic activity and oil conversion were equal on linseed oil and olive oil. The fungus was not able to grow on severe cross-linked linseed oil, meaning that the degree of cross-linking of the oil is important for growth of A. melanogenum. Dark coloring of the colony was seen on linseed oil, which might be a stress response on the presence of autoxidation products in linseed oil. The colony on olive oil showed delayed melanin production indicating an inhibitory effect of olive oil on melanin production. © 2018 The Authors. MicrobiologyOpen published by John Wiley & Sons Ltd.

Environmentally adjusted oil and grease

International Nuclear Information System (INIS)

Andersson, Bert; Lindberg, J.

1992-01-01

With the intention of maintaining healthy environment in our rivers Vattenfall in 1988 initiated a project called 'Environmentally friendly oils'. The goal was to find oils for bearings and hydraulic systems that would cause less negative environmental effects and still maintain a good technical function. Based on the results of the project it is recommended, for both economical and environmental reasons, to change to synthetic oil in bearings and to hydraulic oil made of white oil in regulating systems. The change may be carried out in connection to other work on the system in question. Special care is recommended when cleaning the system from old oil and dirt. In order to maintain the high quality of the oil, also during manufacturing and assembling, one should follow the recommendations outlined in the report. In bearings where used grease leaks into the river, a grease made of white oil should be used. The quality of the rubber sealings must be adapted to the oil used, in order to secure a good function. In order to bring down the number of products and to create an open market some additional changes is necessary in the specifications of oil. Further research regarding oil and sealing is planned. (3 refs.)

Huff-type competitive facility location model with foresight in a discrete space

OpenAIRE

Milad Gorji Ashtiani; Ahmad Makui; Reza Ramezanian

2011-01-01

Consider a chain as leader that wants to open p new facilities in a linear market, like metro. In this market, there is a competitor, called follower. The leader and the follower have established some facilities in advance. When the leader opens p new facilities, its competitor, follower, reacts the leader’s action and opens r new facilities. The optimal locations for leader and follower are chosen among predefined potential locations. Demand is considered as demand points and is assumed inel...

The Galeta oil spill: Pt. 1

International Nuclear Information System (INIS)

Garrity, S.D.; Levings, S.C.; Burns, K.A.

1994-01-01

In April 1986, more than 75 000 barrels (1.5 x 10 7 l) of medium-weight crude oil spilled into Bahia las Minas on the central Caribbean coast of Panama. Changes in the physical structure of the mangrove fringe after oiling were documented over time. These included defoliation, limb loss and eventual collapse of dead trees. By 5 years after the spill, the length of shore fringed by mangroves was reduced at oiled sites relative to unoiled sites. Surviving trees at oiled sites had fewer and shorter submerged prop roots and a higher proportion of dead roots than trees at unoiled sites. These changes reduced the surface area of submerged prop roots by 33% on oiled open coast, 38% in channels and 74% in streams. (author)

Industry-led program recycles used oil materials

International Nuclear Information System (INIS)

Anon.

1997-01-01

The Alberta Used Oil Management Association (AUOMA) is running an industry-led program for recycling used oil filters, containers and used oil. The objective of the program is to help develop an infrastructure that will make recycling simple and convenient for consumers of oil materials. It was estimated that millions of litres of used oil are improperly discarded into the Alberta environment. The program is also aimed at increasing public awareness of the importance of recycling used oil materials, particularly to those consumers who change their own motor oil. By the end of 1997 AUOMA expects to open about 50 recycling centres called EcoCentres. An environmental handling charge (EHC) will be paid to AUOMA by wholesale suppliers on the first sale of oil materials in Alberta. The EHC will be the only funds used to support the program

Outline of a fuel treatment facility in NUCEF

International Nuclear Information System (INIS)

Sugikawa, Susumu; Umeda, Miki; Kokusen, Junya

1997-03-01

This report presents outline of the nuclear fuel treatment facility for the purpose of preparing solution fuel used in Static Experiment Critical Facility (STACY) and Transient Experiment Critical Facility (TRACY) in Nuclear Fuel Cycle Safety Engineering Research Facility (NUCEF), including descriptions of process conditions and dimensions of major process equipments on dissolution system of oxide fuel, chemical adjustment system, purification system, acid recovery system, solution fuel storage system, and descriptions of safety design philosophy such as safety considerations of criticality, solvent fire, explosion of hydrogen and red-oil and so on. (author)

More oil sand cooperation between Canada and Venezuela

Energy Technology Data Exchange (ETDEWEB)

1977-07-01

Venezuela has pioneered the production of heavy oil, according to Dr. A. Guzman-Reyes, director general of hydrocarbons for the Venezuelan government. The first heavy oil production began in Venezuela 60 yr ago and the oil industry has steadily improved methods of producing and handling heavy oil. The country's producing fields are capable of yielding almost one million barrels of heavy oil daily, although actual production, largely because of market limitations, is about 650,000 bpd. Canada's daily heavy oil production, including the 60,000 bbl of synthetic crude produced daily by the Great Canadian Oil Sands plant, is about 200,000 bbl. Dr. Guzman-Reyes stated that Venezuela intends to rapidly develop heavy oil production and upgrade facilities to maintain its export markets. The national oil company, Petroleos de Venezuela, plans to invest 4 times the amount spent on oil development over the last 60 yr during the next 10 yr, a total of $3 billion by 1980.

Bioremediation of offshore oil spills

International Nuclear Information System (INIS)

Goldman, E.; Tedaldi, D.J.

1994-01-01

This research program was directed towards the enhancement of insitu biorestoration of open sea oil spills. Bacteria possessing petroleum degrading enzymes are capable of splitting even thick, viscous oils and tars into lighter fractions. This process will occur at the oil/bacterial interface and depends upon viscosity of the oil, bacterial species, availability of ancillary nutrients, residence times and extent of mixing/oxygenation. Through the enzymatic metabolism of bacteria, a wide range of petroleum oils can be converted almost completely into CO 2 , water, cell mass and harmless biological waste products, usually within 60 to 90 days under favorable conditions. Specifically, this research work focused on the selection and examination of a floating medium which enhances the biodegradation process through improvement of conditions necessary for the process to occur. An additional effort was made to update previous citations of the order of magnitude of oil biodegradation rates and to compare laboratory measurements of biodegradation rates with field or mesocosm measurements

COMPARISON OF AN INNOVATIVE NONLINEAR ALGORITHM TO CLASSICAL LEAST SQUARES FOR ANALYZING OPEN-PATH FOURIER TRANSFORM INFRARED SPECTRA COLLECTED AT A CONCENTRATED SWINE PRODUCTION FACILITY

Science.gov (United States)

Open-path Fourier transform infrared (OP/FTIR) spectrometry was used to measure the concentrations of ammonia, methane, and other atmospheric gases at an integrated swine production facility. The concentration-pathlength products of the target gases at this site often exceeded th...

Reception and treatment facilities for waste oils and oil-polluted waters from marine and industrial activities in Gothenburg, Sweden

International Nuclear Information System (INIS)

Andersson, K.; Lexen, S.I.; Hell, M.

1992-01-01

At the beginning of the 1980s, comprehensive solutions were found to problems associated with the handling of oil-polluted water from marine and industrial sources in the Gothenburg area. The treatment plant in the oil harbour has permission to treat 700,000 m 3 /yr of sludge, ballast, slops and other oil-contaminated waters. Following treatment by chemical flocculation, flotation and dual-media filtration, the treated water must not contain more than 5 ppm of oil. Work to improve treatment results has been carried out from the start, in close co-operation with environmental authorities and with the waste generators themselves. Through increased consciousness, improvements in control, and greater source separation, it will be possible to bring about a significantly lower concentration of pollutants in the incoming waste streams. Recent plans include separate treatment of waste streams containing aromatic compounds and heavily polluted waters. Complementary treatment methods, such as activated carbon and air stripping, are under evaluation. (author). 10 figs

Application of synthetic fire-resistant oils in oil systems of turbine equipment for NPPs

Science.gov (United States)

Galimova, L. A.

2017-10-01

Results of the investigation of the synthetic fire-resistant turbine oil Fyrquel-L state in oil systems of turbosets under their operation in the equipment and oil supply facilities of nuclear power plants (NPPs) are presented. On the basis of the analysis of the operating experience, it is established that, for reliable and safe operation of the turbine equipment, at which oil systems synthetic fire-resistant oils on the phosphoric acid esters basis are used, special attention should be paid to two main factors, namely, both the guarantee of the normalized oil water content under the operation and storage and temperature regime of the operation. Methods of the acid number maintenance and reduction are shown. Results of the analysis and investigation of influence of temperature and of the variation of the qualitative state of the synthetic fair-resistant oil on its water content are reported. It is shown that the fire-resistant turbine oils are characterized by high hydrophilicity, and, in distinction to the mineral turbine oils, are capable to contain a significant amount of dissolved water, which is not extracted under the use of separation technologies. It is shown that the more degradation products are contained in oil and higher acid number, the more amount of dissolved water it is capable to retain. It is demonstrated that the organization of chemical control of the total water content of fireresistant oils with the use of the coulometric method is an important element to support the reliable operation of oil systems. It is recommended to use automatic controls of water content for organization of daily monitoring of oil state in the oil system. Recommendations and measures for improvement of oil operation on the NPP, the water content control, the use of oil cleaning plants, and the oil transfer for storage during repair works are developed.

Treating hydrocarbon oils

Energy Technology Data Exchange (ETDEWEB)

Young, J

1871-08-11

An apparatus is illustrated. It consists of a cistern of stone in which an inclined diaphragm is situated. The acid passes in below the inclined diaphragm by the pipe, and having acted upon the oil beneath the diaphragm any unabsorbed portion escapes through the opening at its highest end.

Arctic oil exploration Former mayor says yes

Energy Technology Data Exchange (ETDEWEB)

Kaleak, J. Sr.

Alaska's coastal plain can sustain both wilderness values and oil production, says Jeslie Kaleak, Sr., former mayor of North Slope Borough in Borrow, Alaska. Kaleak is director is Barrow Operations for North Slope Regional Corporation. Nevertheless, Kaleak contends, [open quotes]the people in the Lower 48 want to keep us from developing this land because of some preconceived notion of the land as a wilderness paradise.[close quotes] Kaleak insists that the Inupiaq people, American Indians inhabiting the Northern Slope region, have provided for their families for thousands of years by turning to the natural environment. Their decision to support oil development is no different. Kaleak contends that the mineral and oil wealth of the North Slope has allowed the Inupiaq people to improve their standard of living drastically. Oil development on the coastal plain, Kaleak contends, could provide similar economic benefits. [open quotes]We cannot define our lives by the vision of distant people who view the North Slope as one great outdoor Disneyland where...all resources remain off limits to us,[close quotes] Kaleak concludes.

Producing electricity from Israel oil shale with PFBC technology

International Nuclear Information System (INIS)

Grinberg, A.; Keren, M.; Podshivalov, V.; Anderson, J.

2000-01-01

Results of Israeli oil shale combustion at atmospheric pressure in the AFBC commercial boiler manufactured by Foster Wheeler Energia Oy (Finland) and in the pressurized test facility of ABB Carbon AB (Finspong, Sweden) confirm suitability of fluidized-bed technologies in case of oil shale. The results approve possibility to use the PFBC technology in case of oil shale after solving of some problems connected with great amounts of fine fly ash. (author)

Open Data for Territorial Specialization Assessment Territorial Specialization in Attracting Local Development Funds: an Assessment. Procedure Based on Open Data and Open Tools

Directory of Open Access Journals (Sweden)

Giuseppe Las Casas

2014-05-01

Full Text Available The New Cohesion Policy opens to an integrated place-based approach for the improvement of territorial and social cohesion. The issue of territorial impact assessment of regional development policies highlight that data availability, open access to datasets in “near real-time”, participation, knowledge sharing, assumed importance within the development planning process. The contribution of ‘open data’ appears to be mature and in this paper we present an application of spatial analysis techniques for the evaluation of spatial effects of EU funds starting form open data by open-coesione. The application regards an internal areas of Basilicata Region: the Agri Valley. A complex contests in which an environmental and agricultural traditional vocation conflicts with a recent development of oil extraction industries. Conclusions regard further applications and perspectives for improving and supporting regional development planning considering the exploitation of open data sources and spatial analysis.

Review on innovative techniques in oil sludge bioremediation

Science.gov (United States)

Mahdi, Abdullah M. El; Aziz, Hamidi Abdul; Eqab, Eqab Sanoosi

2017-10-01

Petroleum hydrocarbon waste is produced in worldwide refineries in significant amount. In Libya, approximately 10,000 tons of oil sludge is generated in oil refineries (hydrocarbon waste mixtures) annually. Insufficient treatment of those wastes can threaten the human health and safety as well as our environment. One of the major challenges faced by petroleum refineries is the safe disposal of oil sludge generated during the cleaning and refining process stages of crude storage facilities. This paper reviews the hydrocarbon sludge characteristics and conventional methods for remediation of oil hydrocarbon from sludge. This study intensively focuses on earlier literature to describe the recently selected innovation technology in oily hydrocarbon sludge bioremediation process. Conventional characterization parameters or measurable factors can be gathered in chemical, physical, and biological parameters: (1) Chemical parameters are consequently necessary in the case of utilization of topsoil environment when they become relevant to the presence of nutrients and toxic compounds; (2) Physical parameters provide general data on sludge process and hand ability; (3) Biological parameters provide data on microbial activity and organic matter presence, which will be used to evaluate the safety of the facilities. The objective of this research is to promote the bioremediating oil sludge feasibility from Marsa El Hariga Terminal and Refinery (Tobruk).

Complications of cataract surgery in eyes filled with silicone oil.

Science.gov (United States)

Kanclerz, Piotr; Grzybowski, Andrzej; Schwartz, Stephen G; Lipowski, Paweł

2018-03-01

The aim of the study was to evaluate complications of cataract surgery in eyes filled with silicone oil. This retrospective, noncomparative, consecutive case series analyzed medical files of patients with eyes filled with silicone oil undergoing cataract surgery. Phacoemulsification with posterior chamber intraocular lens implantation was conducted with or without concurrent silicone oil removal. In this study, 121 eyes of 120 patients were included. In 32 eyes (26.4%) with evident silicone oil microemulsification or silicone oil-associated open-angle glaucoma, silicone oil was removed prior to phacoemulsification through a pars plana incision and no cases of posterior capsular rupture occurred during the subsequent cataract surgery. In the remaining 89 eyes, phacoemulsification was performed with silicone oil in the vitreous cavity. In these eyes, the rate of posterior capsular rupture was 9/89 (10.1%) and the rate of silicone oil migration into the anterior chamber through an apparently intact posterior capsule was 5/89 (5.6%). In 94 eyes (77.7%), an intraocular lens was inserted into the capsular bag, in 3 eyes (2.5%) into the sulcus, and in 1 eye (0.8%) a transscleral suturing was performed. In this series, complications related to the silicone oil were not uncommon during cataract surgery. In the majority of patients without evident silicone oil microemulsification or silicone oil-associated open-angle glaucoma, cataract surgery and posterior chamber intraocular lens implantation were performed while leaving the silicone oil in place.

Ex situ bioremediation of mineral oil in soils: Aerated pile treatment. Final report

International Nuclear Information System (INIS)

Graves, D.

1998-04-01

Under a contract with Southern Company Services, a pilot-scale evaluation of mineral oil biodegradation was conducted at Plant Mitchell. The evaluation consisted of two demonstrations to examine land treatment and aerated pile treatment of soil contaminated with the mineral insulating oil used in electrical transformers. Treatment of mineral oil contaminated soil is problematic in the State of Georgia and throughout the US because current practice is to excavate and landfill the contaminated soil. In many cases, the cost associated with these activities far exceeds the environmental risk of mineral oil in soil. This project was designed to evaluate the performance of bioremediation for the treatment of mineral oil in soil. Testing was carried out in a demonstration facility prepared by Georgia Power Company. The facility consisted of 12 independent treatment cells constructed on a concrete pad and covered with a roof

Kauai Test Facility hazards assessment document

Energy Technology Data Exchange (ETDEWEB)

Swihart, A

1995-05-01

The Department of Energy Order 55003A requires facility-specific hazards assessment be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Kauai Test Facility, Barking Sands, Kauai, Hawaii. The Kauai Test Facility`s chemical and radiological inventories were screened according to potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance to the Early Severe Health Effects threshold is 4.2 kilometers. The highest emergency classification is a General Emergency at the {open_quotes}Main Complex{close_quotes} and a Site Area Emergency at the Kokole Point Launch Site. The Emergency Planning Zone for the {open_quotes}Main Complex{close_quotes} is 5 kilometers. The Emergency Planning Zone for the Kokole Point Launch Site is the Pacific Missile Range Facility`s site boundary.

Oil and gas industry, exploration and development

International Nuclear Information System (INIS)

Appert, O.

1998-01-01

A consistent investment boost on exploration and development, the favourable prospects connected with technological improvement, the opening of virgin areas of exploration are all factors granting extraordinary opportunities for the oil and gas industry. However, environmental constraints relevant to emission standards and products quality are also growing and will be increasingly binding upon both oil and car industries [it

Apparatus for recovering oil from Posidonien shale

Energy Technology Data Exchange (ETDEWEB)

1920-04-13

Equipment for recovering oil from shale and the like, as well as the distilling of coal is characterized in that a number of chambers provided in a known way with upper and lower air supply are arranged open to the receiver of the oil vapors through removable domes which can be attached to the usual oil-vapor carry-off. Arrangement is characterized in that the domes are movable to the side, so that they can be interchangeably attached to the different chambers.

Effective operational oil spill response planning

International Nuclear Information System (INIS)

Meyers, R.J.

1991-01-01

An operational Contingency Plan is one of the single most important aspects of effective oil spill response operations. It is a spill control game plan. A thorough contingency plan provides a set of guidelines that can be used to help direct all phases of spill response activities. More than simple a compilation of lists and rosters, the contingency plan reflects strategic and philosophical elements of spill response that help to ensure a viable response to any spill incident. Facilities and oil carrying vessels should have well maintained contingency plans with these features. This paper describes the requirement for effective oil spill response pans and the training required to exercise them

The impact of energy derivatives on the crude oil market

Energy Technology Data Exchange (ETDEWEB)

Fleming, J.; Ostdiek, B. [Jones Graduate School of Management, Rice University, MS 531, P.O. Box 1892 Houston, TX (United States)

1999-04-01

We examine the effects of energy derivatives trading on the crude oil market. There is a common public and regulatory perception that derivative securities increase volatility and can have a destabilizing effect on the underlying market. Consistent with this view, we find an abnormal increase in volatility for three consecutive weeks following the introduction of NYMEX crude oil futures. While there is also evidence of a longer-term volatility increase, this is likely due to exogenous factors, such as the continuing deregulation of the energy markets. Subsequent introductions of crude oil options and derivatives on other energy commodities have no effect on crude oil volatility. We also examine the effects of derivatives trading on the depth and liquidity of the crude oil market. This analysis reveals a strong inverse relation between the open interest in crude oil futures and spot market volatility. Specifically, when open interest is greater, the volatility shock associated with a given unexpected increase in volume is much smaller. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

The impact of energy derivatives on the crude oil market

International Nuclear Information System (INIS)

Fleming, J.; Ostdiek, B.

1999-01-01

We examine the effects of energy derivatives trading on the crude oil market. There is a common public and regulatory perception that derivative securities increase volatility and can have a destabilizing effect on the underlying market. Consistent with this view, we find an abnormal increase in volatility for three consecutive weeks following the introduction of NYMEX crude oil futures. While there is also evidence of a longer-term volatility increase, this is likely due to exogenous factors, such as the continuing deregulation of the energy markets. Subsequent introductions of crude oil options and derivatives on other energy commodities have no effect on crude oil volatility. We also examine the effects of derivatives trading on the depth and liquidity of the crude oil market. This analysis reveals a strong inverse relation between the open interest in crude oil futures and spot market volatility. Specifically, when open interest is greater, the volatility shock associated with a given unexpected increase in volume is much smaller. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

Crude oil growth impact on pipelines

International Nuclear Information System (INIS)

Devries, O.

2005-01-01

This paper provided an outline of crude oil production and supply in Canada. Details of oil sands projects in Athabasca, Cold Lake and Peace River were presented. A chart of oil sands growth by major project was provided. A list of new emerging oil sands crude types was also presented along with details of a synthetic bitumen blending synergy. Maps of Western Canadian crude oil markets were provided, along with details of refinery and market demand by crude type. Various pipeline alternatives to new markets were examined, with reference to Enbridge Pipeline's supply and capacity. Details of the Hardisty to U.S Gulf Coast Pipeline and the Edmonton to Prince Rupert Pipeline and its terminal and dock facilities were presented. It was concluded that pipeline capacity and seasonal factors will influence market demand, while linefill, crude types and the quality of the product will influence operational strategies. tabs., figs

4-Hydroxy-3-methoxycinnamate esters of milkweed oil: synthesis and characterization.

Science.gov (United States)

Harry-O'kuru, Rogers E

2005-11-01

The common milkweed (Asclepias syriaca L.) is a new industrial crop. Its seed oil (TAG) is highly polyunsaturated. In the search for novel applications for milkweed seed oil, the olefinic groups in the TAG were oxidized to polyhydroxy TAG via epoxidation and subsequent epoxy ring-opening reactions. These polyhydroxy TAG exhibit unique industrially desirable emulsoid properties in water. Esterification of the secondary polyhydroxy functionalities of the TAG derivatives of the oil with trans-4-hydroxy-3-methoxycinnamic acid (ferulic acid) has resulted in the development of novel cinnamate esters of milkweed oil. These cinnamates are also obtainable via direct ring-opening of the epoxy TAG intermediate with ferulic acid. Among the interesting characteristics of the ester derivatives is their UV radiation-absorbing property.

Cleaning oil refining drainage waters out of emulsified oil products with thermic treated cedar nut shell

Science.gov (United States)

Pyatanova, P. A.; Adeeva, L. N.

2017-08-01

It was elaborated the ability of the sorbent produced by thermic treatment of cedar nut shell to destruct model and real first kind (direct) emulsions in static and dynamic conditions. In static conditions optimal ratio sorbent-emulsion with the original concentration of oil products 800 mg/l was in the range of 2.0 g per 100 ml of emulsion which corresponds to the level of treatment 94.9%. The time of emulsion destruction was 40 minutes. This sorbent is highly active in dynamic processes of oil-contaminated water treatment, the level of treatment 96.0% is being achieved. Full dynamic sorptive capacity of the sorbent is 0.85 g/g. Sorbent based on the thermic treated cedar nut shell can be elaborated as sorptive filter element of local treatment facilities of oil refining and petrochemical processes. After the treatment with this sorbent of drainage waters of oil refinery in dynamic conditions the concentration of oil products became less than mpc on oil products for waste waters coming to biological treatment.

Plant-wide Control for Better De-oiling of Produced Water in Offshore Oil & Gas Production

DEFF Research Database (Denmark)

Yang, Zhenyu; Stigkær, Jens Peter; Løhndorf, Bo

2013-01-01

This paper discusses the application of plant-wide control philosophy to enhance the performance and capacity of the Produced Water Treatment (PWT) in offshore oil & gas production processes. Different from most existing facility- or material-based PWT innovation methods, the objective of this work...

Environmental Assessment for decommissioning the Strategic Petroleum Reserve Weeks Island Facility, Iberia Parish, Louisiana

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

The Strategic Petroleum Reserve (SPR) Weeks Island site is one of five underground salt dome crude oils storage facilities operated by the Department of Energy (DOE). It is located in Iberia Parish, Louisiana. The purpose of the proposed action is to decommission the Weeks Island crude oil storage after the oil inventory has been transferred to other SPR facilities. Water intrusion into the salt dome storage chambers and the development of two sinkholes located near the aboveground facilities has created uncertain geophysical conditions. This Environmental Assessment describes the proposed decommissioning operation, its alternatives, and potential environmental impacts. Based on this analyses, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) and has issued the Finding of No Significant Impact (FONSI).

Environmental Assessment for decommissioning the Strategic Petroleum Reserve Weeks Island Facility, Iberia Parish, Louisiana

International Nuclear Information System (INIS)

1995-12-01

The Strategic Petroleum Reserve (SPR) Weeks Island site is one of five underground salt dome crude oils storage facilities operated by the Department of Energy (DOE). It is located in Iberia Parish, Louisiana. The purpose of the proposed action is to decommission the Weeks Island crude oil storage after the oil inventory has been transferred to other SPR facilities. Water intrusion into the salt dome storage chambers and the development of two sinkholes located near the aboveground facilities has created uncertain geophysical conditions. This Environmental Assessment describes the proposed decommissioning operation, its alternatives, and potential environmental impacts. Based on this analyses, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) and has issued the Finding of No Significant Impact (FONSI)

Automated DNA extraction platforms offer solutions to challenges of assessing microbial biofouling in oil production facilities.

Science.gov (United States)

Oldham, Athenia L; Drilling, Heather S; Stamps, Blake W; Stevenson, Bradley S; Duncan, Kathleen E

2012-11-20

The analysis of microbial assemblages in industrial, marine, and medical systems can inform decisions regarding quality control or mitigation. Modern molecular approaches to detect, characterize, and quantify microorganisms provide rapid and thorough measures unbiased by the need for cultivation. The requirement of timely extraction of high quality nucleic acids for molecular analysis is faced with specific challenges when used to study the influence of microorganisms on oil production. Production facilities are often ill equipped for nucleic acid extraction techniques, making the preservation and transportation of samples off-site a priority. As a potential solution, the possibility of extracting nucleic acids on-site using automated platforms was tested. The performance of two such platforms, the Fujifilm QuickGene-Mini80™ and Promega Maxwell®16 was compared to a widely used manual extraction kit, MOBIO PowerBiofilm™ DNA Isolation Kit, in terms of ease of operation, DNA quality, and microbial community composition. Three pipeline biofilm samples were chosen for these comparisons; two contained crude oil and corrosion products and the third transported seawater. Overall, the two more automated extraction platforms produced higher DNA yields than the manual approach. DNA quality was evaluated for amplification by quantitative PCR (qPCR) and end-point PCR to generate 454 pyrosequencing libraries for 16S rRNA microbial community analysis. Microbial community structure, as assessed by DGGE analysis and pyrosequencing, was comparable among the three extraction methods. Therefore, the use of automated extraction platforms should enhance the feasibility of rapidly evaluating microbial biofouling at remote locations or those with limited resources.

Colombian fusel oil

Directory of Open Access Journals (Sweden)

Natalia Montoya

2016-05-01

Full Text Available By-products valorization in bio-fuels industry is an important issue for making the global process more efficient, more profitable and closer to the concept of biorefinery. Fusel oil is a by-product of bioethanol production that can be considered as an inexpensive and renewable raw material for manufacturing value-added products. In this work, results in terms of composition and physicochemical properties of six samples of fusel oil from industrial alcohol facilities are presented. Composition of the main components was established by gas chromatography. Complementary techniques, such as headspace solid-phase microextraction and gas chromatography–mass spectrometry (GC-MS, were used for detection of minor components. Fifty-five compounds were identified. Physicochemical properties such as density, acid value, moisture content and true boiling point curves were determined. Results are useful in the conceptual design of separation strategies for recovering higher alcohols, as well as to consider new options of valorization alternatives for fusel oil.

Experimental study of the processes of aerosol production for technical oil cleanup

Directory of Open Access Journals (Sweden)

Medvedev Gennadiy

2017-01-01

Full Text Available From the experimental study of mechanism of fine mist formation in oil-flooded screw compressor it has been drawn the conclusion on evaporation of fine aerosol of mineral oil that has been obtained in two ways: on the basis of oil spray with mechanical burner and on the basis of volume condensation of oil vapour in air. The given paper presents experimental facility for the production of mineral oil aerosol and also comparison of the experimentation results with calculations.

Oil and development

Energy Technology Data Exchange (ETDEWEB)

Ellis, F

1974-10-01

The shift in world income due to the increase in oil prices has resulted in a world economy that has been thrown off balance. Nine papers are presented that explore the background and the main implications of this ''watershed'' in international relations, particularly the extent to which it will affect the development prospects of poor countries and the climate of trade between poor and rich nations in the next few years. Two papers, ''Diary of Events in the Oil Market 1971--1974'' and ''Statistical Background,'' provide information on the financial changes implied by the price increase; some of the figures should be treated as preliminary estimates only. ''Large International Firms in the Oil Industry'' examines the part played by the major oil companies in developments in the oil market leading up to the events of 1973. Two papers, ''Can OPEC Maintain Current Prices'' and ''OPEC As a Model for Other Mineral Exporters,'' present optimistic conclusions, from the viewpoint of developing countries, on their future capability for controlling their own destinies in trade. ''A Note on Some Issues Raised for Science and Technology Policy by the Increase in Oil Prices'' looks at options open to producers and consumers of raw materials. ''Assessing the Economic Impact on Developing Countries and Some Policy Suggestions,'' ''A Note on the Implications of the Oil Price Increases for British Aid Policy,'' and ''Confrontation Versus Co-operation'' are three papers concerned with difficulties of developing countries and particularly India, Bangladesh, and Sri Lanka. (MCW)

Ecological and Economic Indicators of Oil and Gas Companies Functioning

Directory of Open Access Journals (Sweden)

Anastasia V. Sheveleva

2016-01-01

Full Text Available This article analyzes the basic ecological-economic indicators of oil and gas companies, in particular the various volumes of oil, the number of spills per year of CO2 emissions, the costs of environmental protection. In the process of exploration, development and exploitation of oil and gas fields, production, refining, transportation and storage companies have a negative impact on the environment. Occur accidents involving oil spills, emissions and discharges of pollutants into the environment. As a result contaminates water resources, soil and atmosphere, animals dying, birds and fish, but also transformed the structure of the subsurface and changes the landscape, reduced strategic reserves of fuel and energy resources are formed objects of accumulated environmental damage. The need for construction of environmental protection facilities; the protection, rational use and rehabilitation of lands; protection of water resources and atmospheric air; monitoring the environment and industrial facilities; the prevention and elimination of consequences of accidents on pipelines; disposal and recycling of waste; environmental education; conducting scientific research requires oil and gas companies to undertake large expenditures. A positive trend of modern development of oil and gas companies is the introduction of mechanisms for environmental management in practice their activities, which leads to a gradual reduction of the negative impact of their activities on the environment.

Major oil spills, St. Croix, U.S. Virgin Islands

International Nuclear Information System (INIS)

Bills, C.E.; Whiting, D.C.

1990-01-01

The destruction caused by Hurricane Hugo resulted in two major oil spills on the island of St. Croix, U.S. Virgin Islands. Roughly 10,000 barrels of oil were discharged from damaged storage tanks at the Hess Oil Virgin Island Corporation and 14,000 barrels of oil were discharged from the Virgin Islands Water and Power Authority facility in Christiansted. Pollution responders overcame the lack of power, water, food lodging, communications and transportation to perform an effective cleanup of these spills. This paper presents details of the pollution response effort as coordinated by the Federal On Scene Coordinator

Future prospects for palm oil refining and modifications

Directory of Open Access Journals (Sweden)

Gibon Véronique

2009-07-01

Full Text Available Palm oil is rich in minor components that impart unique nutritional properties and need to be preserved. In this context, refining technologies have been improved, with the dual temperature deodorizer, the double condensing unit and the ice condensing system. The DOBI is a good tool to assess quality of the crude palm oil and its ability to be properly refined. Specially refined oils open a market for new high quality products (golden palm oil, red palm oil, white soaps, etc.. Palm oil is a good candidate for the multi-step dry fractionation process, aiming to the production of commodity oils and specialty fats (cocoa butter replacers. New technological developments allow quality and yield improvements. Palm oil and fractions are also valuable feedstock for enzymatic interesterification in which applications are for commodity oil (low-trans margarines and shortenings and for special products (cocoa butter equivalents, infant formulation, ….

The Aurora accelerator's triggered oil switch

International Nuclear Information System (INIS)

Weidenheimer, D.M.; Pereira, N.R.; Judy, D.C.; Stricklett, K.L.

1993-01-01

Achieving a radiation pulse with 15 ns risetime using all four of the Aurora accelerator's Blumlein pulse-forming lines demands synchronization of the Blumleins to within 10 ns (in addition to a 15 ns risetime for a single line). Timing of each Blumlein is controlled by a triggered 12 MV oil switch. A smaller-than-customary trigger electrode makes the switching time more reproducible. Time-resolved photography of the oil arcs suggests that triggering occurs simultaneously around the sharp edge of the trigger electrode, perhaps with small deviations that grow into the most prominent arcs characteristically seen in open-shutter photographs. However, many smaller arcs that are usually overlooked in open-shutter pictures may contribute to current conduction in a closed switch

Oil Extraction from “Morelos Rice” Bran: Kinetics and Raw Oil Stability

Directory of Open Access Journals (Sweden)

J. Zúñiga-Diaz

2017-01-01

Full Text Available “Morelos rice” is a variety of rice with certificate of denomination of origin. It is a large grain of opaque appearance and extra large size that is grown exclusively in Morelos state (Mexico. Thus, the quality and characteristics of its rice bran may affect the kinetic of the extraction process of its oil as well as its stability. Therefore, this work is oriented to determine the extraction kinetics of its oil and its oxidative stability. The latter one is obtained through the proposal of a method based on open-circuit potential measurements. The results showed that the rice bran has 21.44% of raw oil, with a chemical composition (based on fatty acids of 48.48% oleic acid, 35.26% linoleic acid, and 14.54% palmitic acid, as well as a free fatty acid content of 8.15%. A high percentage of its oil content can be recovered in a short time at room temperature, and its extraction kinetics is a function of both the washing and the diffusion of its oil. Under storage conditions the raw oil has a high stability, at least 8 months, and its oxidative stability was of 24, 9, and 7 hours at 50°C, 80°C, and 110°C, respectively.

Dynamic Oil-in-Water Concentration Acquisition on a Pilot-Scaled Offshore Water-Oil Separation Facility

DEFF Research Database (Denmark)

Løhndorf, Petar Durdevic; Raju, Chitra Sangaraju; Bram, Mads Valentin

2017-01-01

This article is a feasibility study on using fluorescence-based oil-in-water (OiW) monitors for on-line dynamic efficiency measurement of a deoiling hydrocyclone. Dynamic measurements are crucial in the design and validation of dynamic models of the hydrocyclones, and to our knowledge, no dynamic...

A facile method for emulsified oil-water separation by using polyethylenimine-coated magnetic nanoparticles

Science.gov (United States)

Lü, Ting; Qi, Dongming; Zhang, Dong; Lü, Yulan; Zhao, Hongting

2018-04-01

Oil spills and oily wastewater discharges from ships and industrial activities have serious impacts on the environment and human health. In this study, a class of easy-to-synthesize polyethylenimine (PEI)-coated Fe3O4 magnetic nanoparticles (MNPs) was successfully synthesized via a one-step coprecipitation method. The synthesized PEI-coated Fe3O4 MNPs were characterized by using multiple technologies and applied in emulsified oil-water separation for the first time. It was found that the PEI effectively tuned the surface charge and wettability of MNPs. As a result, the PEI-coated MNPs could successfully assemble at the oil-water interface and promote the coalescence of oil droplets, thereby facilitating the subsequent magnetic separation. Results showed that the oil-water separation performance was superior and enhanced with the increase of ionic strength. Recycling experiment indicated that the PEI-coated MNPs could be reused up to six times without showing a significant decrease in separation efficiency. All of these results suggested that the PEI-coated MNP could potentially be used as a class of promising nanomaterials for emulsified oil-water separation. [Figure not available: see fulltext.

Biocorrosive Thermophilic Microbial Communities in Alaskan North Slope Oil Facilities

Energy Technology Data Exchange (ETDEWEB)

Duncan, Kathleen E.; Gieg, Lisa M.; Parisi, Victoria A.; Tanner, Ralph S.; Green Tringe, Susannah; Bristow, Jim; Suflita, Joseph M.

2009-09-16

Corrosion of metallic oilfield pipelines by microorganisms is a costly but poorly understood phenomenon, with standard treatment methods targeting mesophilic sulfatereducing bacteria. In assessing biocorrosion potential at an Alaskan North Slope oil field, we identified thermophilic hydrogen-using methanogens, syntrophic bacteria, peptideand amino acid-fermenting bacteria, iron reducers, sulfur/thiosulfate-reducing bacteria and sulfate-reducing archaea. These microbes can stimulate metal corrosion through production of organic acids, CO2, sulfur species, and via hydrogen oxidation and iron reduction, implicating many more types of organisms than are currently targeted. Micromolar quantities of putative anaerobic metabolites of C1-C4 n-alkanes in pipeline fluids were detected, implying that these low molecular weight hydrocarbons, routinely injected into reservoirs for oil recovery purposes, are biodegraded and provide biocorrosive microbial communities with an important source of nutrients.

Processing of oil products using complex radiation-thermal treatment and radiation oxonolysis

International Nuclear Information System (INIS)

Zaikin, Yu.A.; Zaikina, R.F.

2002-01-01

Most of industrial radiation facilities afford an opportunity to produce a considerable amount of reactive ozone-containing gaseous mixtures parallel to the basic production that causes no detriment to the output of the main designed product. The synergetic action of the ozone-containing mixtures and ionizing radiation is of a special interest for industrial application since it can be efficiently used in a wide range of technologies, in particular, for stimulation of chemical conversion in hydrocarbons accompanied by intensive oxidizing processes. In this paper the effect of simultaneous radiation-thermal processing and radiation oxonolysis on hydrocarbon chemical conversion, and subsequent alterations in composition and properties of oil products were studied on the example of high-viscous oil (Karazhanbas field, Kazakhstan) subjected to irradiation by 2 MeV electrons combined with radiation ozonization in the bubbling mode. It was stated that application of the bubbling mode for radiation-induced ozonization of high-viscous oil leads to decrease in the yields of engine fuels in average by 8-10 % compared with those obtained in the conditions when radiation-thermal cracking was applied without bubbling. In the latter case mean yields of the wide gas-oil fraction with boiling start temperature of 350 deg. C, that included gasoline, kerosene, and diesel fuel, were about 76-80 %. Decrease in the gasoline yields does not lead to noticeable alterations in hydrocarbon contents of the gasoline fraction (boiling beginning bellow 175 deg. C) compared with gasoline produced be radiation-thermal cracking, in both cases it meets requirements for high quality standards. However, essential difference was observed in properties of heavy residua of oil processing (oil fractions with T boil >350 deg. C), i.e. the fractions that contained high concentrations of asphaltenes and pitches. Application of radiation oxonolysis diminishes concentrations of high-molecular aromatic

Olive oil: an overview of the Japanese market

Directory of Open Access Journals (Sweden)

Capogna Daniela

2016-11-01

Full Text Available The article presents an overview of olive oil consumption in Japan, Asia’s largest per capita consumer and at present 14th in the world. Since the early 1990s, total purchases have increased from 4943 t in the 1992/93 campaign to 61 903 t in 2014/15, a more than 12-fold increase over the space of 22 years. Olive oil, in particular extra virgin olive oil, is appreciated by Japanese people primarily for its beneficial effects on health, as well as for its agreeable taste and for its cultural and historical associations. Other key factors to be considered are economic and cultural. Japan is one of the world’s largest economies; disposable incomes are high and these are reflected in household consumption behavior. Culturally, the country is increasingly open to the outside world, discovering and adopting practices from elsewhere, notably the West. This openness, allied to the country’s relative affluence, is demonstrated in the consumption of olive oil, a pillar of the Mediterranean Diet.

Offset Risk Minimization for Open-loop Optimal Control of Oil Reservoirs

DEFF Research Database (Denmark)

Capolei, Andrea; Christiansen, Lasse Hjuler; Jørgensen, J. B.

2017-01-01

Simulation studies of oil field water flooding have demonstrated a significant potential of optimal control technology to improve industrial practices. However, real-life applications are challenged by unknown geological factors that make reservoir models highly uncertain. To minimize...... the associated financial risks, the oil literature has used ensemble-based methods to manipulate the net present value (NPV) distribution by optimizing sample estimated risk measures. In general, such methods successfully reduce overall risk. However, as this paper demonstrates, ensemble-based control strategies...... practices. The results suggest that it may be more relevant to consider the NPV offset distribution than the NPV distribution when minimizing risk in production optimization....

A summary review of modelling oil in ice

International Nuclear Information System (INIS)

Khelifa, A.

2009-01-01

The increase of maritime shipping and industrial developments in the Arctic increases the risk for potential oil spills in ice. Such spills are difficult to track, may contaminate vast areas after the melting season and may take months to clean. As such, there is a need for robust spill models that can predict the trajectory and fate of soil spilled in ice. This paper summarized the results obtained from a recent review on the state of knowledge on modelling approaches developed during the last 4 decades to predict transport and weathering of oil spilled in ice-infested waters. It showed that modelling oil spills on ice is much less developed than oil-spill modelling in open water. There appears to be a lag between the advancement of understanding the fate and behaviour and the integration of the results into operational oil-spill models. The most widely used method consists of adapting existing open-water oil spill models to ice-infested waters by introducing a correction factor proportional to ice coverage to key processes controlling the transport and weathering of oil in ice. Few models use a quadratic scaling factor. As such most existing oil spill models are inadequate to accurately reproduce field observations related to oil spills in ice. Existing data shows that variations of evaporation and emulsification rates are not linearly correlated with the percentage of ice coverage. The decrease in these rates is a function of the ice coverage, the type of ice, and varies with time after the spill. The study found that future models for oil spill in ice-infested waters should be combined with robust ice models coupled with atmospheric models, circulation models and wave models which includes the effect of ice. The dynamic approach was shown to adapt well to coupling with ice models. 81 refs., 2 tabs.

DEVELOPMENT AND APPLICATION OF PROTOCOLS FOR EVALUATION OF OIL SPILL BIOREMEDIATION (RESEARCH BRIEF)

Science.gov (United States)

Protocols were developed and evaluated to assess the efficacy and environmental safety of commercial oil spill bioremediation agents (CBAs). Test systems that simulate oil slicks on open water or oiled sandy beaches were used to test the effectiveness of CBAs. Gravimetric and gas...

Superhydrophobic silica wool—a facile route to separating oil and hydrophobic solvents from water

Science.gov (United States)

Crick, Colin R.; Bhachu, Davinder S.; Parkin, Ivan P.

2014-12-01

Silica microfiber wool was systematically functionalized in order to provide an extremely water repellent and oleophilic material. This was carried out using a two-step functionalization that was shown to be a highly effective method for generating an intense water repulsion and attraction for oil. A demonstration of the silica wools application is shown through the highly efficient separation of oils and hydrophobic solvents from water. Water is confined to the extremities of the material, while oil is absorbed into the voids within the wool. The effect of surface functionalization is monitored though observing the interaction of the material with both oils and water, in addition to scanning electron microscope images, x-ray photoelectron spectroscopy and energy dispersive x-ray analysis. The material can be readily utilized in many applications, including the cleaning of oil spills and filtering during industrial processes, as well as further water purification tasks—while not suffering the losses of efficiency observed in current leading polymeric materials.

open-quotes Shift-Betelclose quotes: A (very) distributed mainframe

International Nuclear Information System (INIS)

Segal, B.; Martin, O.; Hassine, F.; Hemmer, F.; Jouanigot, J.M.

1994-01-01

Over the last four years, CERN has progressively converted its central batch production facilities from classic mainframe platforms (Cray XMP, IBM, ESA, Vax 9000) to distributed RISC based facilities, which have now attained a very large size. Both a CPU-intensive system (open-quotes CSFclose quotes, the Central Simulation Facility) and an I/O-intensive system (open-quotes SHIFTclose quotes, the Scaleable Heterogeneous Integrated Facility) have been developed, plus a distributed data management subsystem allowing seamless access to CERN'S central tape store and to large amounts of economical disk space. The full system is known as open-quotes COREclose quotes, the Centrally Operated Risc Environment; at the time of writing CORE comprises around 2000 CERN Units of Computing (about 8000 MIPs) and over a TeraByte of online disk space. This distributed system is connected using standard networking technologies (IP protocols over Ethernet, FDDI and UltraNet), but which until quite recently were only implemented at sufficiently high speed in the Local Area

Antimicrobial activity of essential oils against Staphylococcus aureus biofilms.

Science.gov (United States)

Vázquez-Sánchez, Daniel; Cabo, Marta L; Rodríguez-Herrera, Juan J

2015-12-01

The present study was aimed to evaluate the potential of essential oils to remove the foodborne pathogen Staphylococcus aureus from food-processing facilities. The effectiveness of 19 essential oils against planktonic cells of S. aureus was firstly assessed by minimal inhibitory concentration. Planktonic cells showed a wide variability in resistance to essential oils, with thyme oil as the most effective, followed by lemongrass oil and then vetiver oil. The eight essential oils most effective against planktonic cells were subsequently tested against 48-h-old biofilms formed on stainless steel. All essential oils reduced significantly (p oils were the most effective, but high concentrations were needed to achieve logarithmic reductions over 4 log CFU/cm(2) after 30 min exposure. Alternatively, the use of sub-lethal doses of thyme oil allowed to slow down biofilm formation and to enhance the efficiency of thyme oil and benzalkonium chloride against biofilms. However, some cellular adaptation to thyme oil was detected. Therefore, essential oil-based treatments should be based on the rotation and combination of different essential oils or with other biocides to prevent the emergence of antimicrobial-resistant strains. © The Author(s) 2014.

Adaptive algorithm of selecting optimal variant of errors detection system for digital means of automation facility of oil and gas complex

Science.gov (United States)

Poluyan, A. Y.; Fugarov, D. D.; Purchina, O. A.; Nesterchuk, V. V.; Smirnova, O. V.; Petrenkova, S. B.

2018-05-01

To date, the problems associated with the detection of errors in digital equipment (DE) systems for the automation of explosive objects of the oil and gas complex are extremely actual. Especially this problem is actual for facilities where a violation of the accuracy of the DE will inevitably lead to man-made disasters and essential material damage, at such facilities, the diagnostics of the accuracy of the DE operation is one of the main elements of the industrial safety management system. In the work, the solution of the problem of selecting the optimal variant of the errors detection system of errors detection by a validation criterion. Known methods for solving these problems have an exponential valuation of labor intensity. Thus, with a view to reduce time for solving the problem, a validation criterion is compiled as an adaptive bionic algorithm. Bionic algorithms (BA) have proven effective in solving optimization problems. The advantages of bionic search include adaptability, learning ability, parallelism, the ability to build hybrid systems based on combining. [1].

The oil field chemists role during field abandonment

Energy Technology Data Exchange (ETDEWEB)

Read, P.A.; Alfsnes, K.

1996-12-31

During the next ten years an increasing number of redundant oil and gas production facilities are scheduled for decommissioning on the Norwegian continental shelf. The oil field chemists role in this connection is discussed. Many of the facilities are large combined drilling and production platforms, others no more than field control centres. Their construction materials and methods are very varied, ranging from steel jackets to concrete gravity structures. Many sub sea templates and flow lines will be targeted for removal. An initial review of a simple production platform has revealed the presence of almost 800 chemical substances. The environmental fate of the materials is needed for estimating the best possible environmental option for the disposal of installations and their contents

Hippocampus lipid peroxidation induced by residual oil fly ash intranasal instillation versus habituation to the open field.

Science.gov (United States)

Zanchi, Ana Claudia; Saiki, Mitiko; Saldiva, Paulo Hilário Nascimento; Barros, Helena Maria Tannhauser; Rhoden, Claudia Ramos

2010-01-01

Epidemiological studies have demonstrated the adverse effects of particulate matter (PM) inhalation on the respiratory and cardiovascular systems. It has been reported that air pollution may affect the central nervous system and decrease cognitive function. In rats, residual oil fly ash (ROFA) instillation causes decreased motor activity and increased lipid peroxidation in the striatum and the cerebellum. Our objective was to determine whether chronic instillation of particles induces changes in learning and memory in rats and whether oxidants in the hippocampus may contribute to these adverse effects. Forty-five-day-old male Wistar rats were exposed to ROFA by intranasal instillation and were treated with N-acetylcysteine (NAC) at 150 mg/kg i.p. for 30 days. Control groups were exposed to ROFA, NAC, or neither. On days 1, 8, and 30 of the protocol, rats were submitted to the open field test to evaluate habituation. After the last open field session, the rats were killed by decapitation. The hippocampus was used to determine lipid peroxidation (LP) by the thiobarbituric acid-reactive substances test. ROFA instillation induced an increase in LP in the hippocampus compared to all treatment groups (p = .012). NAC treatment blocked these changes. All of the treatment groups presented a decrease in the frequency of peripheral walking (p = .001), rearing (p = .001), and exploration (p = .001) over time. Our study demonstrates that exposure to particles for 30 days and/or NAC treatment do not modify habituation to an open field, a simple form of learning and memory in rats, and that oxidative damage induced by ROFA does not modulate these processes.

Selection for a Zinc-Finger Protein Contributes to Seed Oil Increase during Soybean Domestication1[OPEN

Science.gov (United States)

Li, Qing-Tian; Lu, Xiang; Song, Qing-Xin; Chen, Hao-Wei; Wei, Wei; Tao, Jian-Jun; Ma, Biao; Bi, Ying-Dong; Li, Wei; Lai, Yong-Cai; Shui, Guang-Hou; Chen, Shou-Yi

2017-01-01

Seed oil is a momentous agronomical trait of soybean (Glycine max) targeted by domestication in breeding. Although multiple oil-related genes have been uncovered, knowledge of the regulatory mechanism of seed oil biosynthesis is currently limited. We demonstrate that the seed-preferred gene GmZF351, encoding a tandem CCCH zinc finger protein, is selected during domestication. Further analysis shows that GmZF351 facilitates oil accumulation by directly activating WRINKLED1, BIOTIN CARBOXYL CARRIER PROTEIN2, 3-KETOACYL-ACYL CARRIER PROTEIN SYNTHASE III, DIACYLGLYCEROL O-ACYLTRANSFERASE1, and OLEOSIN2 in transgenic Arabidopsis (Arabidopsis thaliana) seeds. Overexpression of GmZF351 in transgenic soybean also activates lipid biosynthesis genes, thereby accelerating seed oil accumulation. The ZF351 haplotype from the cultivated soybean group and the wild soybean (Glycine soja) subgroup III correlates well with high gene expression level, seed oil contents and promoter activity, suggesting that selection of GmZF351 expression leads to increased seed oil content in cultivated soybean. Our study provides novel insights into the regulatory mechanism for seed oil accumulation, and the manipulation of GmZF351 may have great potential in the improvement of oil production in soybean and other related crops. PMID:28184009

Determination of hydrogen content of Jatropha biodiesel oil using neutron reflection technique

International Nuclear Information System (INIS)

Okunade, I. O.; Jonah, S. A.; Omede, M.

2014-01-01

Biofuel is an environmental-friendly alternative to fossil fuel and holds immense potential for the future energy needs of the country. Non-edible jatropha biodiesel oil has been identified as one of the suitable bio-fuel options. In this work, experimental measurements were performed to determine the total hydrogen content of jatropha oil and jatropha-synthetic diesel oil mixture. The work was carried out using a neutron reflection facility at the Centre for Energy Research and Training, Ahmadu Bello University, Zaria. Jatropha oil and jatropha-synthetic diesel mixture were subjected to experimental measurements for the purpose of determining bulk hydrogen content using neutron reflection facility that had been previously calibrated using various hydrocarbon materials of known hydrogen content. The hydrogen content of the sample were subsequently determined using their measured neutron reflection coefficient values and calibration data. In general, results obtained indicate high hydrogen content range of 10.68-12.16wt% for jatropha oil and the various jatropha-synthetic diesel mixtures. The implication of this is that jatropha oil or jatrophal-synthetic diesel mixture can be used as alternative fuel to mitigate high carbon monoxide emission.

The SWARF high energy flash X-ray facility

International Nuclear Information System (INIS)

Gilbert, J.F.; Dove, E.W.D.

1976-06-01

A description is presented of the SWARF flash radiography facility at AWRE Foulness, which is stated to be the most powerful flash x-ray system available, in the U.K. The machine consists essentially of a Marx generator, a coaxial Blumlein system and an x-ray tube. The voltage output from the Marx generator (about 2.5 MV from an 80 kV input) is applied to a large re-entrant Blumlein pulse-forming line. Near maximum voltage, an adjustable oil switch short-circuits one end of the Blumlein generator and so applies a square voltage pulse of 65 ns duration to the x-ray tube. The x-rays are produced from a tantalum target which forms the anode of a vacuum field emission diode. The facility consists of two field machines positioned so that radiographs can be obtained from different angles. The description is given under the following heads: modus operandi; constructional details; oil installation; electrical details; commissioning, calibration and electrical data; flash radiography in explosives research; operational control of facility, film packs; radiographic results; further developments; overall performance. (U.K.)

From oil sands to transportation fuels, to electricity, to hydrogen

International Nuclear Information System (INIS)

Yildirim, E.

1993-01-01

The Alberta Chamber of Resources programs and initiatives on oil sands and heavy oil, and strategies for revitalizing oilsands development in Alberta are described. The regional upgrader and satellite production facilities concept, and technology requirements for mineable oil sands by the year 2010 are discussed. Strategic alliances in furtherence of oil sands research and development and the National Task Force on Oil Sands Strategies are described. Changes in requirements for transportation fuels due to stricter regulations and environmental initiatives will cause a trend to lighter fuels with more hydrogen content, less aromatics, nitrogen, sulfur and metals. A preferred refinery configuration will be able to process heavier crudes and synthetic crudes, have no heavy fuel oil product, low sulfur products, low aromatics with high octane, and low operating cost. A regional or central facility that combines the processing capabilities of a bitumen upgrader with the process units of a refinery is preferred. Advantages of this concept are: value addition to the feedstock is maximized; dependence on refineries is eliminated; restriction on synthetic crude oil volumes due to capacity limitations at refineries is eliminated; directly marketable finished products are produced; more stringent quality specifications are satisfied; and the synergies between upgrading and refining improve overall economics of processing. It is recommended that the concept of regional upgraders be adopted for Alberta, strategic alliances be encouraged, incentives for bitumen production be provided, and a bitumen pipeline network be developed. 12 refs

External irradiation facilities open for biological studies - progress in july 2005

International Nuclear Information System (INIS)

Gaillard-Lecanu, E.; Authier, N.; Verrey, B.; Bailly, I.; Bordy, J.M.; Coffigny, H.; Cortela, L.; Duval, D.; Leplat, J.J.; Poncy, J.L.; Testard, I.; Thuret, J.Y.

2005-01-01

The Life Science Division of the Atomic Energy Commission is making an inventory of the various radiation sources accessible for investigation on the biological effects of ionizing radiation. In this field, a wide range of studies is being carried out at the Life Science Division, attempting to characterize the kind of lesions with their early biological consequences (on the various cell compartments) and their late biological consequences (deterministic or stochastic effects), in relation to the radiation type and dose, especially at low doses. Several experimental models are available: plants, bacteria, eukaryotic cells from yeast up to mammalian cells and in vivo studies, mostly on rodents, in order to characterize the somatic late effects and the hereditary effects. Due to the significant cost of these facilities, also to their specific properties (nature of the radiation, dose and dose rate, possible accuracy of the irradiation at the molecular level), the closeness is no longer the only criteria for biologists to make a choice. The current evolution is to set up irradiation infrastructures combining ionizing radiation sources themselves and specific tools dedicated to biological studies: cell or molecular biology laboratories, animal facilities. The purpose, in this new frame, is to provide biologists with the most suitable facilities, and, if possible, to change these facilities according to requirements in radiobiology. In this report, the basics of interactions of ionizing radiation with biological tissues are briefly introduced, followed by a presentation of some of the facilities available for radiobiological studies especially at CEA. This panorama is not a comprehensive one, new data will be included as they advance, whether reporting existing facilities or if a new one is developed. (authors)

Vehicle for removing pollutants, especially oil, from the surface of waters

Energy Technology Data Exchange (ETDEWEB)

Cornelissen, J

1968-11-28

A vessel for removing pollutants from the surface of water consists of wings extending transversally from the axis of the vessel. The wings are partially immersed in the water and are arranged at an angle, so that when the vessel is in motion, the oil is driven over the upper edge of the wing into a separation chamber. The chamber has a circular cross section and ends in an opening in the hull of the ship, where the polluting oil is collected. The opening and the channel have such a shape that the mixture of water and pollutant enters the opening in a turbulent stream. (8 claims)

Survey of tritiated oil sources and handling practices

International Nuclear Information System (INIS)

Miller, J.M.

1994-08-01

Tritium interactions with oil sources (primarily associated with pumps) in tritium-handling facilities can lead to the incorporation of tritium in the oil and the production of tritiated hydrocarbons. This results in a source of radiological hazard and the need for special handling considerations during maintenance, decontamination, decommissioning and waste packaging and storage. The results of a general survey of tritiated-oil sources and their associated characteristics, handling practices, analysis techniques and waste treatment/storage methods are summarized here. Information was obtained from various tritium-handling laboratories, fusion devices, and CANDU plants. 38 refs., 1 fig

Smoke and mirrors: used oil management policy in Ontario

International Nuclear Information System (INIS)

Valiante, U.

1997-01-01

The burning of used oil for space heating is a practice that has been increasing since 1992 when the waste fuel regulation was amended to give northern generators without access to used oil collection an option for managing their used oil. In 1996, about 10 million litres of used oil was burned in Ontario at over 600 locations, in garages, automotive repair facilities, industrial locations and greenhouses. The modified space heaters that burn used motor oils operate without pollution controls. In addition to emissions associated with pollution from uncontrolled combustion, used oil fired space heaters burn what should be a reusable commodity that is high in value added chemical and energy content. A comparison of emissions in grams per 1000 hours of use of a used oil heater and a natural gas heater was presented. It was suggested that as the preferred environmental strategy, the Ontario government should encourage used oil collectors and re-refiners to make used oil management convenient, accessible, and cost-effective in order to protect the health of communities in which used oil is generated

Hazard identification studies applied to oil pipelines

Energy Technology Data Exchange (ETDEWEB)

Savio, Augusto; Alpert, Melina L. [TECNA S.A., Buenos Aires (Argentina)], e-mail: asavio@tecna.com, e-mail: malpert@tecna.com

2008-07-01

In order to assess risks inherent to an Oil Pipeline, it is imperative to analyze what happens 'outside the process'. HAZID (HAZard IDentification) studies are mainly carried out for this purpose. HAZID is a formal study which identifies hazards and risks associated to an operation or facility and enable its acceptability assessment. It is a brainstorming exercise guided by a typical 'Checklist', divided into four Sections: External, Facilities and Health Hazards and Issues pertaining to Project Execution, which are further subdivided into Hazard Categories. For each Category, there are 'Guide-words' and 'Prompts'. Even if an Oil Pipeline Risk Assessment can be performed by means of the above referred 'Checklist', carrying out the actual process can become lengthy and annoying due to the lack of specificity. This work aims at presenting the most suitable 'Checklist' for the identification of Oil Pipeline Risk Assessment, although it could be used for Gas Pipeline Risk Assessment too. Prepared ad hoc, this list, is based on the spill causes established by CONCAWE (CONservation of Clean Air Water in Europe). Performing Oil Pipeline Risk Assessment by means of specially formulated Checklist enables the Study Team to easily identify risks, shortens execution time and provides both accuracy and specificity. (author)

Heavy mineral concentration from oil sand tailings

Energy Technology Data Exchange (ETDEWEB)

Chachula, F.; Erasmus, N. [Titanium Corp. Inc., Regina, SK (Canada)

2008-07-01

This presentation described a unique technique to recover heavy minerals contained in the froth treatment tailings produced by oil sand mining extraction operations in Fort McMurray, Alberta. In an effort to process waste material into valuable products, Titanium Corporation is developing technology to recover heavy minerals, primarily zircon, and a portion of bitumen contained in the final stage of bitumen processing. The process technology is being developed to apply to all mined oil sands operations in the Fort McMurray region. In 2004, Titanium Corporation commissioned a pilot research facility at the Saskatchewan Research Council to test dry oil sands tailings. In 2005, a bulk sampling pilot plant was connected to the fresh oil sands tailings pipeline on-site in Fort McMurray, where washed sands containing heavy minerals were processed at a pilot facility. The mineral content in both deposited tailings and fresh pipeline tailings was assessed. Analysis of fresh tailings on a daily basis identified a constant proportion of zircon and higher levels of associated bitumen compared with the material in the deposited tailings. The process flow sheet design was then modified to remove bitumen from the heavy minerals and concentrate the minerals. A newly modified flotation process was shown to be a viable processing route to recover the heavy minerals from froth treatment tailings. 8 refs., 9 tabs., 12 figs.

Coated kapok fiber for removal of spilled oil

International Nuclear Information System (INIS)

Wang, Jintao; Zheng, Yian; Wang, Aiqin

2013-01-01

Highlights: ► A low-cost and biodegradable oil absorbent based on kapok fiber was prepared. ► The polymer-coated kapok fiber showed higher oil sorption capacity. ► Coated kapok fiber can be reused and the absorbed oil can be easily recovered. ► Adsorption of oil is spontaneous and exothermic physisorption and chemisorption. -- Abstract: Based on raw kapok fiber, two kinds of oil absorbers with high sorption capacity were prepared by a facile solution–immersion process. The coated polymer with low surface energy and rough fiber surface play important role in the retention of oil. The as-prepared fiber can quickly absorb gasoline, diesel, soybean oil, and paraffin oil up to above 74.5%, 66.8%, 64.4% and 47.8% of oil sorption capacity of raw fiber, respectively. The absorbed oils can be easily recovered by a simple vacuum filtration and the recovered coated-fiber still can be used for several cycles without obvious loss in oil sorption capacity. The thermodynamic study indicates that the adsorption process is spontaneous and exothermic, with complex physisorption and chemisorption. The results suggest that the coated fiber can be used as a low-cost alternative for the removal of oil spilled on water surface

Managing Mexican Oil: Politics or Economics?

Directory of Open Access Journals (Sweden)

Alicia Puyana Mutis

2008-07-01

Full Text Available During decades the policies towards oil and energy implemented in Mexico have resulted in the de pletion of reserves, the explosion of debt of Pemex (90 per cent of its capital, and the dramatic petrolization of the total fiscal revenue. High prices, the war on terror and political instability in oil rich regions have reinforced usA policy of "energy security" and the interest in the creation of the Common Market on Energy, as the way to strengthen the TLCAN. To respond to these two forces Mexico will have to reform its traditional oil policy. All possible options: to reduce the fiscal burden upon Pemex or to open to private investments the exploration of oil have excruciating political costs, which no government has shown the will to confront.

Feasibility study for a biodiesel refining facility in the Regional Municipality of Durham

International Nuclear Information System (INIS)

Villeneuve, S.; Saville, B.

2006-02-01

Although both public and political support for renewable fuels is currently strong, the next decade will determine if the biodiesel industry in North America will expand to make significant contributions to rural economic development and to improve urban air quality. The feasibility of establishing a biodiesel production facility in the Region of Durham, Ontario was investigated. The study included an assessment of potential sites, feedstock assessments, biodiesel market analysis, preliminary cost estimates and financial analysis. The purpose was to establish which feedstocks and technology options are viable and to document the underlying assumptions with historical data, cost estimates and projections. Six suitable sites in the region were evaluated. Two had access to feedstocks brought in by boat, but they were also among the furthest from existing rail lines, which increased the overall site development costs. A sensitivity analysis was conducted to determine the effect of land and site development costs on the return on investment (ROI). It was shown that a $2 MM difference in these costs affects the ROI by 3 to 4 per cent, but not enough to significantly influence the viability of a biodiesel plant in the region. The research and financial analysis revealed that Durham could potentially support a biodiesel production facility that produces up to 38 million litres per year of biodiesel from crude corn oil extracted from corn-to-ethanol processing facilities, supplemented by recycled fats, oils and greases. It was determined that the plant location may depend on access to infrastructure and community, or political acceptance. At $325 per tonne for crude oil, the projected average annual pre-tax ROI for a 38 MM litre per year biodiesel plant using only corn oil is 39 per cent sufficient to recommend a project. It was also determined that there is insufficient animal-derived material available locally to support a biodiesel production facility on recycled fats

Oil-Price Shocks: Beyond Standard Aggregate Demand/Aggregate Supply Analysis.

Science.gov (United States)

Elwood, S. Kirk

2001-01-01

Explores the problems of portraying oil-price shocks using the aggregate demand/aggregate supply model. Presents a simple modification of the model that differentiates between production and absorption of goods, which enables it to better reflect the effects of oil-price shocks on open economies. (RLH)

Evaluation of NORM in facility Venezuelan oil industry to establish regulatory criteria

International Nuclear Information System (INIS)

Acevedo Lozada, D. J.; Rivas, I.; Davila, L.; Flores, Y.

2013-01-01

The present work shows the need to identify, in the Venezuelan oil industry, the existence of exposure to natural sources of radiation should be considered as occupational. As Regulatory Authority in the area of ionizing radiation the need for regulatory processes and ensure radiation protection of personnel involved in these practices arises, as well as personal and environmental monitoring. NORM identifying an installation of the Venezuelan oil industry to establish regulatory processes and take steps to ensure occupational radiation protection. (Author)

Oil and power: Iraq at the crossroads

International Nuclear Information System (INIS)

Enay, P.

1995-11-01

Oil and Power: Iraq at the Crossroads is the first analysis which specifically addresses the oil sector in Iraq. It provides a detailed account of the present Iraqi oil infrastructure and assesses the risks and opportunities facing those who seek to invest in its redevelopment. The report examines the implications for the world oil markets of Iraq's ambitious plans to expand production capacity to 6m barrels per day -almost twice its pre-war peak. It explains in clear, authoritative terms the profound problems confronting Iraq's oil sector and the prospects for rebuilding it. It analyses expertly and in detail the current regime's chances of survival and examines the alternative contenders for power -and their likely attitudes towards co-operation with foreign oil interests. The report examines and explains: Iraq's oil infrastructure, from fields under exploration to nominal administrative structure; the effect on oil prices of Iraq's eventual re-entry into the oil market; the facilities in need of repair and where the shortage of spares and human expertise are; the unofficial decision-making structure in the oil sector; the short- and medium-term impact of economic disintegration on oil development policy; the effects of UN sanctions and the motives of those supporting or opposing sanctions; the likely impact of prevailing economic constraints on Iraqi oil and the historical role of commissions in Iraqi oil contracts; the political impact of General Hussein Kamal Hassan's defection and the Kurdish and Shi'ite threats to Iraqi national unity. (author)

Oil spills and their cleanup

International Nuclear Information System (INIS)

Fingas, M.

1995-01-01

Oil spills are an unfortunately common occurrence in the world's seas and can have extensive damaging environmental consequences. This article examines various methods of cleaning up oil spills, evaluates their effectiveness in various situations, and identifies areas where, current methods being inadequate, further research is needed. Containment, mechanical removal, shoreline cleanup, chemical treating agents, in situ burning, natural recovery and enhanced bioremediation are all assessed. The cleanup method must be selected to match environmental conditions. Results are good in quiet, sheltered waters, but need extensive development in open waters and high seas. (UK)

Use of toxicity assessment to develop site specific remediation criteria for oil and gas facilities : guidance manual

International Nuclear Information System (INIS)

1996-01-01

The results of a two year study into the evaluation of toxicity-based methods to develop site-specific, risk-based cleanup objectives for the decommissioning of oil and gas facilities were compiled into a manual of guidance. The two basic approaches used in determining remediation criteria for contaminated sites are: (1) comparison of the concentrations of chemicals found on-site with broad regional or national soil and water quality objectives developed for the chemicals involved, and (2) site-specific risk assessment. Toxicity tests are used to test organisms such as earthworms, lettuce seeds, or larval fish directly in the soil, water or sediment suspected of being contaminated. The effects of any contamination on the survival, growth, reproduction, and behaviour of the test organisms are then evaluated. The manual provides guidance in: (1) using toxicity assessments within the regulatory framework of site decommissioning, (2) performing a toxicity assessment, and (3) developing site-specific criteria for a risk assessment. 18 refs., 3 tabs., 5 figs

The fate of stranded oil at the BIOS site twenty years after the experiment

International Nuclear Information System (INIS)

Owens, E.H.; Sergy, G.A.; Prince, R.C.

2002-01-01

As part of the 1981 Baffin Island Oil Spill (BIOS) Project, 15 cubic metres of aged crude oil was released onto the shores of an experimental beach at Cape Hatt, northern Baffin Island, Canada. The oil was left to weather naturally and the distribution, quantity and character of the oil was monitored over time. The experiment provided a unique opportunity to study and sample oil as it weathers over a 20 year period in a low-energy, arctic environment. Over the 20 years of the study, the oil was exposed to weathering processes for about 40 months during ice-free periods. While most of the stranded oil was removed in the first few months of open water immediately following the experiment, some small surface patches still persist. It was noted that there has been very little change in the distribution or in the physical condition of the oil patches between 1993 and 2001. Geochemical analysis reveals that some samples are unaltered despite more than 20 years of exposure to elements. Other samples indicate that biodegradation and photo-oxidation play a major role in removing most of the components of the oil in this low-energy arctic environment. Some highly biodegraded samples had less than 87 per cent of the original hydrocarbons. The study revealed that there are 4 stages in the evolution of the stranded oil: (1) initial rapid refloating of oil during the first 24 to 48 hours in 1981, (2) period of relative stability up to the formation of an asphalt pavement within 4 open-water months, (3) degradation of an asphalt pavement in the upper intertidal zone over a 10-month open-water period from August 1983 to August 1989, and (4) disintegration of the pavement after 1989 and before August 1991, with soft interstitial surface oil still present in 2001. 21 refs., 1 tab., 1 fig

High potency fish oil supplement improves omega-3 fatty acid status in healthy adults: an open-label study using a web-based, virtual platform.

Science.gov (United States)

Udani, Jay K; Ritz, Barry W

2013-08-08

The health benefits of omega-3 fatty acids from fish are well known, and fish oil supplements are used widely in a preventive manner to compensate the low intake in the general population. The aim of this open-label study was to determine if consumption of a high potency fish oil supplement could improve blood levels of eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA) and impact SF-12 mental and physical health scores in healthy adults. A novel virtual clinical research organization was used along with the HS-Omega-3 Index, a measure of EPA and DHA in red blood cell membranes expressed as a percentage of total fatty acids that has been shown to correlate with a reduction in cardiovascular and other risk factors. Briefly, adult subjects (mean age 44 years) were recruited from among U.S. health food store employees and supplemented with 1.1 g/d of omega-3 from fish oil (756 mg EPA, 228 mg DHA, Minami Nutrition MorEPA Platinum) for 120 days (n = 157). Omega-3 status and mental health scores increased with supplementation (p < 0.001), while physical health scores remained unchanged. The use of a virtual, web-based platform shows considerable potential for engaging in clinical research with normal, healthy subjects. A high potency fish oil supplement may further improve omega-3 status in a healthy population regularly consuming an omega-3 supplement.

An Experimental Study of Oil / Water Flow in Horizontal Pipes

Energy Technology Data Exchange (ETDEWEB)

Elseth, Geir

2001-07-01

The purpose of this thesis is to study the behaviour of the simultaneous flow of oil and water in horizontal pipes. In this connection, two test facilities are used. Both facilities have horizontal test sections with inner pipe diameters equal to 2 inches. The largest facility, called the model oil facility, has reservoirs of 1 m{sub 3} of each medium enabling flow rates as high as 30 m{sub 3}/h, which corresponds to mixture velocities as high as 3.35 m/s. The flow rates of oil and water can be varied individually producing different flow patterns according to variations in mixture velocity and input water cut. Two main classes of flows are seen, stratified and dispersed. In this facility, the main focus has been on stratified flows. Pressure drops and local phase fractions are measured for a large number of flow conditions. Among the instruments used are differential pressure transmitters and a traversing gamma densitometer, respectively. The flow patterns that appear are classified in flow pattern maps as functions of either mixture velocity and water cut or superficial velocities. From these experiments a smaller number of stratified flows are selected for studies of velocity and turbulence. A laser Doppler anemometer (LDA) is applied for these measurements in a transparent part of the test section. To be able to produce accurate measurements a partial refractive index matching procedure is used. The other facility, called the matched refractive index facility, has a 0.2 m{sub 3} reservoir enabling mainly dispersed flows. Mixture velocities range from 0.75 m/s to 3 m/s. The fluids in this facility are carefully selected to match the refractive index of the transparent part of the test section. A full refractive index matching procedure is carried out producing excellent optical conditions for velocity and turbulence studies by LDA. In addition, pressure drops and local phase fractions are measured. (author)

Canadian Occidental joins Hunt as Yemen oil producer

International Nuclear Information System (INIS)

Gurney, J.

1994-01-01

On 23 September 1993, the Canadian Occidental Petroleum Company initiated the export of 120,000 b/d (barrels a day) of low sulphur, medium gravity crude oil from its Masila Block concession in Yemen. The oil is transported from Masila via a pipeline built by CanOxy and its partners to a new terminal at Ash Shihr, near Mukalla, in the Gulf of Aden. CanOxy is the third operator oil company to produce oil commercially in Yemen. The first, the Hunt Oil Company, began production in December 1987 and its output now totals about 187,000 b/d. The second, Nimir Petroleum, a Saudi venture which took over the facilities developed in the 1980s by two Soviet companies, is currently producing about 10,000 b/d and expects to increase its output to 25,000 b/d during this year. (Author)

Directions in refining and upgrading of heavy oil and bitumen

International Nuclear Information System (INIS)

Dawson, B.; Parker, R. J.; Flint, L.

1997-01-01

The expansion of heavy oil transportation, marketing and refining facilities over the past two decades have been reviewed to show the strides that several Canadian refiners have taken to build up the facilities required to process synthetic crude oil (SCO). Key points made at a conference, convened by the National Centre for Upgrading Technology (NCUT), held in Edmonton during September 1997 to discuss current and future directions in the refining and marketing of heavy oil, bitumen and SCO, were summarized. Among the key points mentioned were: (1) the high entry barriers faced by centralized upgraders, (2) the advantages of integrating SCO or heavy oil production with downstream refining, (3) the stiff competition from Venezuela and Mexico that both SCO and heavy oil will face in the U.S. PADD II market, (4) the differences between Canadian refiners who have profited from hydrocracking and are better able to handle coker-based SCO, and American refiners who rely chiefly on catalytic cracking and are less able to process the highly aromatic SCO, and (5) the disproportionate cost in the upgrading process represented by the conversion of asphaltenes. Challenges and opportunities for key stakeholders, i.e. producers, refiners, marketers and technology licensors also received much attention at the Edmonton conference

Nursing educator's satisfaction with library facilities.

OpenAIRE

Lenz, E R; Waltz, C F

1982-01-01

This study examined nursing faculty perceptions of the importance of adequate library facilities and their satisfaction with them. Library facilities ranked highest in importance among all job characteristics studied, with faculty who had been most productive in terms of publication assigning the highest value to them. A moderate level of satisfaction was found. Faculty most satisfied with library facilities were those teaching in large schools of nursing with graduate programs and open organ...

Computational model for the assessment of oil spill damages

Energy Technology Data Exchange (ETDEWEB)

Seip, K L; Heiberg, A B; Brekke, K A

1985-06-01

A description is given of the method and the required data of a model for calculating oil spill damages. Eleven damage attributes are defined: shorelength contaminated, shore restitution time, birds dead, restitution time for three groups of birds, open sea damages-two types, damages to recreation, economy and fisheries. The model has been applied in several cases of oil pollution assessments: in an examination of alternative models for the organization of oil spill combat in Norway, in the assessment of the damages coused by a blowout at Tromsoeflaket and in assessing a possible increase in oil spill preparedness for Svalbard. 56 references.

Closing and opening fisheries following oil spills; a case study in Humboldt Bay, California

International Nuclear Information System (INIS)

Challenger, G.E.; Mauseth, G.S.

1998-01-01

The issue of fishery evaluation criteria following oil spills in lakes, rivers and seas was discussed. The case of the November 1997 incident in which 4,450 gallons of an intermediate fuel oil was released into Humboldt Bay, California was described. Humboldt Bay contains important shellfish mariculture operations that were subsequently closed by the California Dept. of Health Services (CDHS). The closure and reopening protocols for the fishery were summarized. Suggestions for technical input to resource management decisions were presented. During an initial meeting with regulatory agencies, four levels of criteria were established for rescinding the fishery closure. The fishery closure would be rescinded when: (1) there was a lack of visible oil sheen on the water throughout the commercial growing areas, (2) shellfish tissue samples met the risk-based criteria developed by CDHS, for all analytes of concern in the source oil, (3) all water samples met the risk-based criteria developed by CDHS for all analytes of concern in the source oil, and (4) tissue samples passed an independent sensory evaluation. However, no risk-based water quality criteria were developed and only items 1, 2, and 4 were included in the analysis. 15 refs., 3 tabs., 1 fig

The Hobbs Oil and Water Experimental Facility of the Waste-Management Education and Research Consortium

International Nuclear Information System (INIS)

Martin, F.D.; Bretz, R.E.; Bowman, R.S.; Kieft, T.L.; Cadena, F.

1992-01-01

The Hobbs Oil and Water Experimental (HOWE) Facility came on-line as a research component of the Waste-Management Education and Research Consortium (WERC) when funding for the Consortium became official in late February 1990. As a support facility for WERC, which was established to expand the ability of this nation to manage hazardous, radioactive, and solid wastes through a multidisciplinary approach, HOWE can tap into the expertise that resides at three major New Mexico universities, on Native American community college, and two national laboratories. The intention of the HOWE is to provide education, as well as research and development programs, that reflect concerns of the petroleum industry in the United States. Personnel work to solve environmental problems and assess the impact to the industry of regulatory actions pertaining to those problems. Leadership for the program is provided from the New Mexico Institute of Mining and Technology at Socorro, NM, by Technical Leaders F.D. Martin, Director of the Petroleum Recovery Research Center, and Dr. R.E. Bretz of the petroleum engineering faculty. The HOWE site is administered by Mike DeMarco, Director of the Petroleum Technology Program at the New Mexico Junior College in Hobbs, NM. Currently, the HOWE laboratory is being provided with state-of-the-art equipment to support research projects or field demonstration activities. Programs include research pertaining to groundwater pollution transport processes, slurry-phase bioremediation of oilfield production pit sludges, and treatment of produced brines or contaminated waters. This paper introduces the HOWE and discusses the research programs relevant to the petroleum industry that are presently underway or planned. Future collaborative efforts with industry that are presently underway or planned. Future collaborative efforts with industry groups are being encouraged

CLS A Fully Open-Source Control System

CERN Document Server

Matias, Elder; Johnson, Terry; Tanner, Robby; Wilson, Tony; Wright, Glen; Zhang, Hao

2005-01-01

The Canadian Light Source is one of the first major accelerator facility to adopt a fully open source control system. The control system is based on Experimental Physics and Industrial Control System (EPICS) in use at may other facilities. From the outset CLS utilised RTEMS and Linux as the underlying operating systems for real-time control computers, operator interface computers and servers. When communicating with PLC and other intelligent devices CLS has also adopted a policy of using open communications protocols where possible. Combined these strategies have lead to a system that can easily evolve over the life of the facility without being tied to specific hardware or software suppliers. The operational experience over the past few years has indicates the selected architecture is sufficiently robust and reliable.

North Sea oil and the environment

International Nuclear Information System (INIS)

Cairns, W.J.

1992-01-01

This book, which is arranged in five sections, provides an historical record of the development of North Sea oil and gas over the past twenty years and records the lessons learnt from this experience. This first section provides an introductory framework to the three main themes, namely resources, environment and development. Section 2 is primarily concerned with the economic and social consequences of oil related development at two levels; firstly on the national economy and secondly the impact on local communities. Section 3 deals with impacts upon the physical environment and introduces the statutory land use planning system in Scotland. The Scottish approach to environmental assessment is reviewed and the need for mitigation by design explored. Section 4 examines specific field developments, and reviews the statutory controls and international initiatives regulating the extent of environmental disturbance and pollution from offshore operations. The effects of oil spillage and submarine pipelines on the environment and their impact on the fishing industry is followed by a discussion on the decommissioning and abandonment of offshore installations. Section 5 deals with the role and value of hazard and risk analysis in the siting, layout and safety zoning of onshore facilities and develops a case study on a major fractionation facility. The means of mitigating acute and chronic environmental risks are considered. A postscript provides a range of past comments and criticisms and finally draws some conclusions on the performance of environmental management and North Sea oil development. The North Sea oil and gas development experience proves that with wisdom, forethought and goodwill, industrial exploiters of natural resources can operate economically within legislative, policy, scientific, technical and design parameters without causing long-term irreversible environmental damage. (author)

Environmental perspectives on the East Coast offshore oil and gas industry

International Nuclear Information System (INIS)

Taylor, D.G.

2001-01-01

In this presentation, the author examined the environmental aspects affecting the offshore oil and gas development on the East Coast of Canada. Selected topics were covered to highlight what has been accomplished and the goals for the future in terms of the environment. The development of the oil and gas industry in the region has really taken off in the past twenty years, suffering from growing pains and enduring myths. An oil and gas project begins with seismic surveys, followed by exploratory wells being drilled, then proceeding to the construction and installation of the drilling production facilities, the production phase and the decommissioning of the facilities at the end of the useful life. Each phase of a project was reviewed and environmental concerns identified. Specific topics were addressed, such as drill cuttings, produced water, flaring, and decommissioning and abandonment. Selected problems were examined, notably fish and oil, spills, cumulative effects, the Oceans Act, and the regulatory evolution in the East Coast offshore. 9 refs., 1 tab., 1 fig

Is it all oil?

International Nuclear Information System (INIS)

Asche, Frank; Osmundsen, Petter; Sandsmark, Maria

2003-01-01

After opening up of the Interconnector, the liberalized UK natural gas market and the regulated Continental gas markets became physically integrated. The oil-linked Continental gas price became dominant, due to both the large volume of the Continental market and to the fact that the significant call options embedded in the complex take-or-pay contracts make these contracts the marginal source of supply. However, in an interim period - after deregulation of the UK gas market (1994) and the opening up of the Interconnector (1998) -the UK gas market had neither government price regulation nor a physical Continental gas linkage. We use this period - which for natural gas markets displays an unusual combination of deregulation and autarky - as a natural experiment to explore if decoupling of natural gas prices from prices of other energy commodities, such as oil and electricity, took place. Using monthly price data, we find a highly integrated market where the wholesale demand seems to be for energy rather than a specific energy source. (author)

An analysis of macroeconomic fluctuations for a small open oil-based economy: The case of Saudi Arabia

Science.gov (United States)

Al-Abdulkarim, Bander B.

The increasing fluctuations in the oil prices through the last decades have been transferred to the oil exporting countries. Thus, many oil exporting countries experienced significant changes in the economic activity due to changes in the oil markets. In light of this, oil exporting countries have attempted to implement a policy that would stabilize the fluctuations in the oil markets recognizing the adverse effects of such behavior on oil exporting countries, as well as oil importing countries. Saudi Arabia, as the largest oil-exporting country and a member of OPEC, takes the role of oil-markets stabilizer by behaving as the swing producer. This role has caused the global economic fluctuations to transfer into the domestic economy. In addition, Saudi Arabian government has adopted a fixed exchange rate currency regime. Although it has contributed to domestic price stabilizations, this policy has also exposed the country to global economic disturbances. The purpose of the study is to empirically investigate these aspects for Saudi Arabia. First, the effects of shocks originated in the international markets on the Saudi Arabian economy. Second, how the fixed exchange rate regimes influences the domestic macroeconomic variables. Third, to what extent the oil sector contributes to the non-oil domestic fluctuations. Finally, how the findings from the study can be explained by economic theory. In pursuing this, there are four economic theories that are considered to explain the causes of business cycles. These theories are Classical Theory, Keynesian Theory, Monetarist Theory, and the Real Business Cycles. In addition, a theoretical model is derived that is suitable for an oil-based economy. The model follows the set up of McCallum and Nelson (1999). Then, the empirical models of Structural Vector Autoregression (SVAR) and Error Correction Model (ECM) are implemented with three different specifications: Choleski Decomposition, Block Exogeneity and long-run Cointegration

Realization of Best-in-Class Workflows Using Open Spirit Technology

International Nuclear Information System (INIS)

Hauser, K.

2002-01-01

Open Spirit is the realization of a long sought after dream to create an open systems approach to G and G computing. The focus is on developing a plug-and-play, platform independent, vendor neutral application framework to enable workflow optimization for the oil and gas industry. Through Open Spirit, Oil and gas clients can either develop or purchase Open Spirit enabled applications and combine those applications together to optimize a particular workflow. Currently Open Spirit supports GeoQuest's Geo Frame and Landmark's Open Works project data stores. There are three primary benefits to using Open Spirit enabled applications. Users of Open Spirit enabled applications can access data from a variety of data sources without having to move or reformat the data. This reduces the time to get the information into the appropriate application and eliminates the need to have multiple copies of the same data, simplifying data management efforts. Second, Open Spirit bridges the gap between Unix and PC applications. Through Open Spirit, any applications developed for the NT platform can access information residing in a Unix project data store. Third, Open Spirit supports the concept of a virtual project set. A user can combine any number project data stores (GeoFrame, Open Works, Finder, RECALL and PDS/Tigress) and use the combined project sets as if they were a single project. The data is not moved, but instead accessed dynamically through Open Spirit from the appropriate native data store. Open Spirit allows interpreters to develop their own Best-in-Class workflow and to mix and match the applications they determine to be the best of their interpretation teams independent of vendor

BIOLOGICALLY ACTIVE COMPOUNDS OF ARTEMISIA ANNUA. ESSENTIAL OIL

Directory of Open Access Journals (Sweden)

D. A. Konovalov

2016-01-01

Full Text Available Artemisia annua is a herblike annual plant which has been used in Chinese folk medicine for more than 2,000 years. In 1970-s sesquiterpenic lactone of artemisinin was isolated from the above-ground part of this plant. Today it is the most efficient known natural and synthetic compound for malaria treatment. The purpose of the study was to review the data from the open sources about a component composition of Artemisia annua essential oil in the spectrum of its pharmacological activity. Methods. The study was carried out using information and searching sources (PubMed, ScholarGoogle, library data bases (eLibrary, Cyberleninca, as well as the results of our studies. Results. We have established that aboveground part of Artemisia annua have a significant amount  of essential oil apart from the sesquiterpene lactones. Essential oil contains more than 120 components, which belong to different classes of natural compounds. The study for dynamics of the essential oil accumulation in the Artemisia annua herb showed that the amount of oil in the herb rises significantly during budding, reaching maximum value in blossom. Qualitative composition and quantitative content of certain components varies depending on ecological and  geographical factors,  plant growing phase, cultivation technology, drying methods etc. Well-known pharmacological studies of essential oil of the Artemisia annua characterize it as a prospective source for the development of new antimicrobial medicinal drugs. Besides, as the studies shown, it can be related to the 6 class according to K. Sidorov’s classification – “relatively non-hazardous substances”. Conclusion. The analysis of the open sources on the study of essential oil of Artemisia annua made by us, as well as the results of our own studies, including phytochemical studies allow characterizing the essential oil of Artemisia annua as a prospective source for the working out of new antimicrobial drugs.

DOES VOLATILITY IN CRUDE OIL PRICE PRECIPITATE MACROECONOMIC PERFORMANCE IN NIGERIA?

Directory of Open Access Journals (Sweden)

Joseph Ayoola Omojolaibi

2013-01-01

Full Text Available This study examines the effects of crude oil price changes on economic activity in an oil dependent economy-Nigeria. A small open economy structural vector autoregressive (SVAR technique is employed to study the macroeconomic dynamics of domestic price level, economic output, money supply and oil price in Nigeria. The sample covers the data from 1985:q1 to 2010:q4. The Impulse Response Functions (IRFs and the Forecast Error Variance Decompositions (FEVDs results suggest that domestic policies, instead of oil-boom should be blamed for inflation. Also, oil price variations are driven mostly by oil shocks, however, domestic shocks are responsible for a reasonable portion of oil price variations.

Kauai Test Facility hazards assessment document

International Nuclear Information System (INIS)

Swihart, A.

1995-05-01

The Department of Energy Order 55003A requires facility-specific hazards assessment be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Kauai Test Facility, Barking Sands, Kauai, Hawaii. The Kauai Test Facility's chemical and radiological inventories were screened according to potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance to the Early Severe Health Effects threshold is 4.2 kilometers. The highest emergency classification is a General Emergency at the open-quotes Main Complexclose quotes and a Site Area Emergency at the Kokole Point Launch Site. The Emergency Planning Zone for the open-quotes Main Complexclose quotes is 5 kilometers. The Emergency Planning Zone for the Kokole Point Launch Site is the Pacific Missile Range Facility's site boundary

Offshore newcomer : world-scale megaproject spawns international-calibre skills and facilities

International Nuclear Information System (INIS)

Sorensen, D.

1997-01-01

The development of Hibernia marked the beginning of Newfoundland's booming oil industry. The offshore platform located 300 km offshore in the Grand Banks of Newfoundland has an estimated 615 million barrels of recoverable reserves to be produced at a projected average rate of 135,000 barrels per day. Newfoundland personnel and facilities acquired much expertise during the building of the offshore facility and are ready to enter the world market for oil and gas services and supplies. Newfoundland's biggest operations are the fabrication yards at Bull Arm and Marystown which have the capacity for steel fabrication, concrete construction, outfitting installation, hook-up and commissioning of industrial facilities. Plans are currently underway for the Terra Nova project. Newfoundland also has a strong labor force, with international calibre skills. The capacity is here, and as confidence in that capability increases, Newfoundland firms are beginning to form partnerships with international firms. 6 figs

Transmission cost minimization strategies for wind-electric generating facilities

Energy Technology Data Exchange (ETDEWEB)

Gonzalez, R. [Northern States Power Company, Minneapolis, MN (United States)

1997-12-31

Integrating wind-electric generation facilities into existing power systems presents opportunities not encountered in conventional energy projects. Minimizing outlet cost requires probabilistic value-based analyses appropriately reflecting the wind facility`s operational characteristics. The wind resource`s intermittent nature permits relaxation of deterministic criteria addressing outlet configuration and capacity required relative to facility rating. Equivalent capacity ratings of wind generation facilities being a fraction of installed nameplate rating, outlet design studies contingency analyses can concentrate on this fractional value. Further, given its non-dispatchable, low capacity factor nature, a lower level of redundancy in outlet facilities is appropriate considering the trifling contribution to output unreliability. Further cost reduction opportunities arise from {open_quotes}wind speed/generator power output{close_quotes} and {open_quotes}wind speed/overhead conductor rating{close_quotes} functions` correlation. Proper analysis permits the correlation`s exploitation to safely increase line ratings. Lastly, poor correlation between output and utility load may permit use of smaller conductors, whose higher (mostly off-peak) losses are economically justifiable.

Short Distance Standoff Raman Detection of Extra Virgin Olive Oil Adulterated with Canola and Grapeseed Oils.

Science.gov (United States)

Farley, Carlton; Kassu, Aschalew; Bose, Nayana; Jackson-Davis, Armitra; Boateng, Judith; Ruffin, Paul; Sharma, Anup

2017-06-01

A short distance standoff Raman technique is demonstrated for detecting economically motivated adulteration (EMA) in extra virgin olive oil (EVOO). Using a portable Raman spectrometer operating with a 785 nm laser and a 2-in. refracting telescope, adulteration of olive oil with grapeseed oil and canola oil is detected between 1% and 100% at a minimum concentration of 2.5% from a distance of 15 cm and at a minimum concentration of 5% from a distance of 1 m. The technique involves correlating the intensity ratios of prominent Raman bands of edible oils at 1254, 1657, and 1441 cm -1 to the degree of adulteration. As a novel variation in the data analysis technique, integrated intensities over a spectral range of 100 cm -1 around the Raman line were used, making it possible to increase the sensitivity of the technique. The technique is demonstrated by detecting adulteration of EVOO with grapeseed and canola oils at 0-100%. Due to the potential of this technique for making measurements from a convenient distance, the short distance standoff Raman technique has the promise to be used for routine applications in food industry such as identifying food items and monitoring EMA at various checkpoints in the food supply chain and storage facilities.

75 FR 45572 - Oil Pollution Prevention; Spill Prevention, Control, and Countermeasure (SPCC) Rule-Proposed...

Science.gov (United States)

2010-08-03

... Oil Pollution Prevention; Spill Prevention, Control, and Countermeasure (SPCC) Rule--Proposed... Federal Regulations is proposed to be amended as follows: PART 112--OIL POLLUTION PREVENTION 1. The... certain facilities must prepare or amend their Spill Prevention, Control, and Countermeasure (SPCC) Plans...

Gas migration from oil and gas fields and associated hazards

International Nuclear Information System (INIS)

Gurevich, A.E.; Endres, B.L.; Robertson Jr, J.O.; Chilingar, G.V.

1993-01-01

The migration of gas from oil and gas formations to the surface is a problem that greatly affects those surface areas where human activity exists. Underground gas storage facilities and oil fields have demonstrated a long history of gas migration problems. Experience has shown that the migration of gas to the surface creates a serious potential risk of explosion, fires, noxious odors and potential emissions of carcinogenic chemicals. These risks must be seriously examined for all oil and gas operations located in urban areas. This paper presents the mechanics of gas migration, paths of migration and a review of a few of the risks that should be considered when operating a gas facility in an urban area. The gas can migrate in a continuous or discontinuous stream through porous, water-filled media to the surface. The primary force in this migration of gas is the difference between specific weights of gas and water

Facile solvothermal synthesis of abnormal growth of one-dimensional ZnO nanostructures by ring-opening reaction of polyvinylpyrrolidone

Energy Technology Data Exchange (ETDEWEB)

Xu, G., E-mail: gxu@alum.imr.ac.cn; Wang, X.L.; Liu, G.Z.

2015-02-28

Graphical abstract: - Highlights: • Facile solvothermal synthesis of ZnO nanostructures in super high alkaline alcoholic condition. • The exact role and chemical transformations of PVP in solvothermal synthesis of ZnO nanostructures was revealed. • Mechanism of abnormal growth of ZnO nanopyramids was proposed based on ring-opening reaction of PVP. - Abstract: Abnormal growth of one-dimensional (1-D) ZnO nanostructures (NSs) have been accomplished with the assistance of polyvinylpyrrolidone (PVP) under a super high alkaline alcoholic solvothermal condition. The products were characterized by transmission electron microscopy (TEM), thermogravimetric analysis (TGA), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) and proton nuclear magnetic resonance ({sup 1}H NMR) spectroscopy. The effect of synthetic conditions, such as reaction temperature and the addition of PVP, on the morphologies of ZnO products were investigated. The results show that PVP molecules had the significant role in the transformation of morphologies of ZnO NSs ranging from nanorods, nanoparticles to pyramids, as well as flower-like assembly features. The possible growth mechanism of ZnO pyramids was proposed based on ring-opening reaction of PVP.

Influence of environmental pollution with creosote oil or its vapors on biomass and selected physiological groups of microorganisms

Science.gov (United States)

Krzyśko-Łupicka, Teresa; Cybulska, Krystyna; Kołosowski, Paweł; Telesiński, Arkadiusz; Sudoł, Adam

2017-11-01

Survival of microorganisms in soils from treatment facility and landfill of wooden railway sleepers contaminated with creosote oil as well as in two types of soils with different content of organic carbon, treated with creosote oil vapors, was assessed. Microbiological assays including determination of: the biomass of living microorganisms method and the number of proteolytic, lipolytic and amylolytic microorganisms were carried out under laboratory conditions. Chromatography analysis of the soil extract from railway sleepers treatment facility was performed using GC/MS. The highest biomass and the number of tested microorganisms were determined in soils from wooden railway sleepers landfill, while the lowest in soil from the railway sleepers treatment facility. Vapors of creosote oil, regardless of the soil type, significantly increased only the number of lipolytic bacteria.

AMOP (Arctic Marine Oil Spill Program) studies reviewed

Energy Technology Data Exchange (ETDEWEB)

1978-06-05

A discussion of the Arctic Marine Oil Spill Program organized in 1976 by the Canadian Federal Government includes: an Arctic Atlas compiled by Fenco Consultants Ltd. to give background information necessary for developing marine oil spill countermeasures for the Arctic north of 60/sup 0/ including the west Greenland coast and the Labrador shelf (geology, meteorology and oceanography, ice conditions, biology, and social factors); program in emergency transport of spill-combatting equipment; and the factors which influence the choice of conveyance, i.e., accessibility of the site, urgency for response, and quantity of material required; laboratory studies involving the release of oil under artificial sea ice in simulated ice formation and decay purposes to determine the interaction of crude oil and first-year sea ice; inability of companies and government to control a major spill in the Labrador Sea because of poor and inadequate transport facilities, communications, and navigational aids, severe environmental conditions, and logistics problems; and studies on the effects of oil-well blowouts in deep water, including formation of oil and gas hydrates, design of oil skimmers, the use of hovercraft, and specifications for an airborne multisensor system for oil detection in ice-infested waters.

The interaction of fine particles with stranded oil

International Nuclear Information System (INIS)

Owens, E.H.

1999-01-01

The interaction of micron-sized mineral particles with stranded oil reduces its adhesion to solid surfaces, such as sediments or bedrock. The net result is the formation of stable, micron-sized, oil droplets that disperse into the water column. In turn, the increase in surface area makes the oil more available for biodegradation. Oil and Fine-particle Interaction ('OFI') can explain how oiled shorelines are cleaned naturally in the absence of wave action in very sheltered coastal environments. Fine-particle interaction can be accelerated during a spill response by relocating the oiled sediments into the surf zone. This has been achieved successfully on two occasions to date: the Tampa Bay response in Florida, and the Sea Empress operation in Wales. Sediment relocation also causes physical abrasion by the hydraulic action of waves so that the processes of fine-particle interaction and surf washing usually occur in combination on open coasts. (author)

Estimates of oil entering the marine environment in the past decade : GESAMP Working Group 32 project

International Nuclear Information System (INIS)

Etkin, D.S.; Grey, C.; Wells, P.; Koefoed, J.; Nauke, M.; Meyer, T.; Campbell, J.; Reddy, S.

1998-01-01

A meeting of the Joint Group of Experts on the Scientific Aspects of Marine Protection (GESAMP), Working Group 32, was held to discuss a new approach for evaluating available data sources on the input of oil into the marine environment from sea-based activities. GESAMP Working Group on Estimates of Oil Entering the Marine Environment, Sea Based Activities (Working Group 32) will collect and analyze data on oil inputs over the last decade from shipping, offshore and coastal exploration and production, pipelines, atmospheric emissions from sea-based activities, coastal refineries and storage facilities, oil reception facilities, materials disposed of at sea, and natural seepage. The group will compare its oil input estimate model to estimates made by the National Research Council, the International Maritime Organization (IMO), and GESAMP in previous decades, to evaluate the efficacy of IMO conventions and other pollution reduction efforts in the last 10 years. The group will also consider the amounts of oil entering the sea through operational and accidental spillage in relation to the quantities of oil transported by ship and through pipelines, and in relation to offshore and coastal oil production. 7 refs., 4 tabs

Special report: EC oil market

International Nuclear Information System (INIS)

Anon.

1992-01-01

A European Commission report on the EC's oil market has conceded that the Community will not meet its official objective of reducing oil's share of energy consumption to 40% by 1995. The paper, a 'Communication' to the European Council entitled ''The Oil Market and the Refining Industry in the Community: Recent Developments and Prospects'' says oil will ''continue to account for a major share - of the order of 45% -of the Community's energy consumption'' up to the year 2000. Nonetheless, the report's authors insist the Commission has proposed ''a number of measures'' which could reduce the potential consumption of fossil fuels and help limit CO2 emissions. The report confirms that though lower in 1990 than 1980 at 530mt, oil demand picked up in the second half of the 1980s, reflecting world trends. Little impression has been made on the proportion of the Community's crude supply that is imported. However, one area where the report did find energy objectives successes was that of diversifying sources of crude oil supply. A major source of concern for the Commission at one stage in the second half of the 1980s was the possibility of massive imports of finished oil products from refineries in the oil producing countries. However, the fact that this threat did not materialise is taken as a vindication of the Commission's assessment in previous analyses that ''an open Community market should be maintained''. (author)

Conversion factors and oil statistics

International Nuclear Information System (INIS)

Karbuz, Sohbet

2004-01-01

World oil statistics, in scope and accuracy, are often far from perfect. They can easily lead to misguided conclusions regarding the state of market fundamentals. Without proper attention directed at statistic caveats, the ensuing interpretation of oil market data opens the door to unnecessary volatility, and can distort perception of market fundamentals. Among the numerous caveats associated with the compilation of oil statistics, conversion factors, used to produce aggregated data, play a significant role. Interestingly enough, little attention is paid to conversion factors, i.e. to the relation between different units of measurement for oil. Additionally, the underlying information regarding the choice of a specific factor when trying to produce measurements of aggregated data remains scant. The aim of this paper is to shed some light on the impact of conversion factors for two commonly encountered issues, mass to volume equivalencies (barrels to tonnes) and for broad energy measures encountered in world oil statistics. This paper will seek to demonstrate how inappropriate and misused conversion factors can yield wildly varying results and ultimately distort oil statistics. Examples will show that while discrepancies in commonly used conversion factors may seem trivial, their impact on the assessment of a world oil balance is far from negligible. A unified and harmonised convention for conversion factors is necessary to achieve accurate comparisons and aggregate oil statistics for the benefit of both end-users and policy makers

Open DOAR the Directory of Open Access Repositories

CERN Multimedia

CERN. Geneva

2005-01-01

The last year has seen wide-spread growth in the idea of using open access repositories as a part of a research institution's accepted infrastructure. Policy development from institutions and funding bodies has also supported the growth of the repository network. The next stage of expansion will be in the provision of services and cross-repository facilities and resources. Of course, it is hoped that these will then establish a feed-back loop to encourage repository population and further repository establishment, as the potential of open access to research materials is realised. The growth of repositories has been organic, with a variety of different repositories based in departments, institutions, funding agencies or subject communities, with a range of content, both in type and subject. Existing repositories are expanding their holdings, from eprints to associated research data-sets, or with learning objects and multimedia material. This presentation will look at the development of the Directory of Open Ac...

Oil field experiments of microbial improved oil recovery in Vyngapour, West Siberia, Russia

Energy Technology Data Exchange (ETDEWEB)

Murygina, V.P.; Mats, A.A.; Arinbasarov, M.U.; Salamov, Z.Z.; Cherkasov, A.B.

1995-12-31

Experiments on microbial improved oil recovery (MIOR) have been performed in the Vyngapour oil field in West Siberia for two years. Now, the product of some producing wells of the Vyngapour oil field is 98-99% water cut. The operation of such wells approaches an economic limit. The nutritious composition containing local industry wastes and sources of nitrogen, phosphorus and potassium was pumped into an injection well on the pilot area. This method is called {open_quotes}nutritional flooding.{close_quotes} The mechanism of nutritional flooding is based on intensification of biosynthesis of oil-displacing metabolites by indigenous bacteria and bacteria from food industry wastes in the stratum. 272.5 m{sup 3} of nutritious composition was introduced into the reservoir during the summer of 1993, and 450 m3 of nutritious composition-in 1994. The positive effect of the injections in 1993 showed up in 2-2.5 months and reached its maximum in 7 months after the injections were stopped. By July 1, 1994, 2,268.6 tons of oil was produced over the base variant, and the simultaneous water extraction reduced by 33,902 m{sup 3} as compared with the base variant. The injections in 1994 were carried out on the same pilot area.

Evaluation of anxiolytic and sedative effect of essential oil and hydroalcoholic extract of Ocimum basilicum L. and chemical composition of its essential oil.

Science.gov (United States)

Rabbani, Mohammed; Sajjadi, Seyed Ebrahim; Vaezi, Arefeh

2015-01-01

Ocimum basilicum belongs to Lamiaceae family and has been used for the treatment of wide range of diseases in traditional medicine in Iranian folk medicine. Due to the progressive need to anti-anxiety medications and because of the similarity between O. basilicum and Salvia officinalis, which has anti-anxiety effects, we decided to investigate the anxiolytic and sedative activity of hydroalcoholic extract and essential oil of O. basilicum in mice by utilizing an elevated plus maze and locomotor activity meter. The chemical composition of the plant essential oil was also determined. The essential oil and hydroalcoholic extract of this plant were administered intraperitoneally to male Syrian mice at various doses (100, 150 and 200 mg/kg of hydroalcoholic extract and 200 mg/kg of essential oil) 30 min before starting the experiment. The amount of hydroalcoholic extract was 18.6% w/w and the essential oil was 0.34% v/w. The major components of the essential oil were methyl chavicol (42.8%), geranial (13.0%), neral (12.2%) and β-caryophyllene (7.2%). HE at 150 and 200 mg/kg and EO at 200 mg/kg significantly increased the time passed in open arms in comparison to control group. This finding was not significant for the dose of 100 mg/kg of the extract. None of the dosages had significant effect on the number of entrance to the open arms. Moreover, both the hydroalcoholic extract and the essential oil decreased the locomotion of mice in comparison to the control group. This study shows the anxiolytic and sedative effect of hydroalcoholic extract and essential oil of O. basilicum. The anti-anxiety and sedative effect of essential oil was higher than the hydroalcoholic extract with the same doses. These effects could be due to the phenol components of O. basilicum.

Plan and justification for a Proof-of-Concept oil shale facility

Energy Technology Data Exchange (ETDEWEB)

1990-12-01

The technology being evaluated is the Modified In-Situ (MIS) retorting process for raw shale oil production, combined with a Circulating Fluidized Bed Combustor (CFBC), for the recovery of energy from the mined shale. (VC)

Screening of microorganisms for microbial enhanced oil recovery processes

Energy Technology Data Exchange (ETDEWEB)

Yonebayashi, H. [Japan National Oil Corp., Tokyo (Japan); Yoshida, S. [Japan Food Research Laboratiories, Tokyo (Japan). Div. of Microbiology; Ono, K. [Japan National Oil Corp., Chiba (Japan). Tech. Research Center; Enomoto, H. [Tohoku University, Sendai (Japan). Dept. of Geoscience and Tech.

2000-01-01

The objective of this study is to screen effective microorganisms for the Microbial Enhanced Oil Recovery process (or simply as MEOR). Samples of drilling cuttings, formation water, and soil were collected from domestic drilling sites and oil fields. Moreover, samples of activated-sludge and compost were collected from domestic sewage treatment facility and food treatment facility. At first, microorganisms in samples were investigated by incubation with different media; then they were isolated. By two stage-screening based on metabolizing ability, 4 strains (Bacillus licheniformis TRC-18-2-a, Enterobacter cloacae TRC-322, Bacillus subtilis TRC-4118, and Bacillus subtilis TRC-4126) were isolated as effective microorganisms for oil recovery. B. licheniformis TRC-18-2-a is a multifunctional microorganism possessing excellent surfactant productivity, and in addition it has gas, acid and polymer productivities. E. cloacae TRC-332 has gas and acid producing abilities. B. subtilis TRC-4118 and TRC-4126 are effective biosurfactant producers, and they reduce the interfacial tension to 0.04 and 0.12 dyne/cm, respectively. (author)

Simulation of thin-film deodorizers in palm oil refining

DEFF Research Database (Denmark)

Ceriani, Roberta; Meirelles, Antonio J.A.; Gani, Rafiqul

2010-01-01

As the need for healthier fats and oils (natural vitamin and trans fat contents) and interest in biofuels are growing, many changes in the world's vegetable oil market are driving the oil industry to developing new technologies and recycling traditional ones. Computational simulation is widely used...... in the chemical and petrochemical industries as a tool for optimization and design of (new) processes, but that is not the case for the edible oil industry. Thin-film deodorizers are novel equipment developed for steam deacidification of vegetable oils, and no work on the simulation of this type of equipment...... could be found in the open literature. This paper tries to fill this gap by presenting results from the study of the effect of processing variables, such as temperature, pressure and percentage of stripping steam, in the final quality of product (deacidified palm oil) in terms of final oil acidity...

Oxidative stability of pullulan electrospun fibers containing fish oil

DEFF Research Database (Denmark)

García Moreno, Pedro Jesús; Damberg, Cecilie; Chronakis, Ioannis S.

2017-01-01

The effect of oil content and addition of natural antioxidants on the morphology and oxidative stability of pullulan ultra-thin fibers loaded with fish oil and obtained by electrospinning was investigated. Pullulan sub-micron fibers containing 10 and 30wt% fish oil were prepared and both presented...... into food matrices. These results show the feasibility to encapsulate fish oil in pullulan ultra-thin fibers and to improve their oxidative stability by adding natural antioxidants such as δ-tocopherol and rosemary extract. Therefore, this study might open up new opportunities for further technological...... development in the production of omega-3 nanodelivery systems, which have potential applications in different types of fortified foods. Encapsulation of fish oil in electrospun pullulan fibers stabilized by natural antioxidants....

OpenDrift - an open source framework for ocean trajectory modeling

Science.gov (United States)

Dagestad, Knut-Frode; Breivik, Øyvind; Ådlandsvik, Bjørn

2016-04-01

We will present a new, open source tool for modeling the trajectories and fate of particles or substances (Lagrangian Elements) drifting in the ocean, or even in the atmosphere. The software is named OpenDrift, and has been developed at Norwegian Meteorological Institute in cooperation with Institute of Marine Research. OpenDrift is a generic framework written in Python, and is openly available at https://github.com/knutfrode/opendrift/. The framework is modular with respect to three aspects: (1) obtaining input data, (2) the transport/morphological processes, and (3) exporting of results to file. Modularity is achieved through well defined interfaces between components, and use of a consistent vocabulary (CF conventions) for naming of variables. Modular input implies that it is not necessary to preprocess input data (e.g. currents, wind and waves from Eulerian models) to a particular file format. Instead "reader modules" can be written/used to obtain data directly from any original source, including files or through web based protocols (e.g. OPeNDAP/Thredds). Modularity of processes implies that a model developer may focus on the geophysical processes relevant for the application of interest, without needing to consider technical tasks such as reading, reprojecting, and colocating input data, rotation and scaling of vectors and model output. We will show a few example applications of using OpenDrift for predicting drifters, oil spills, and search and rescue objects.

A Dual-Based Procedure for Dynamic Facility Location

OpenAIRE

Tony J. Van Roy; Donald Erlenkotter

1982-01-01

In dynamic facility location problems, one desires to select the time-staged establishment of facilities at different locations so as to minimize the total discounted costs for meeting demands specified over time at various customer locations. We formulate a particular dynamic facility location problem as a combinatorial optimization problem. The formulation permits both the opening of new facilities and the closing of existing ones. A branch-and-bound procedure incorporating a dual ascent me...

Multi-objective model of waste transportation management for crude palm oil industry

Science.gov (United States)

Silalahi, Meslin; Mawengkang, Herman; Irsa Syahputri, Nenna

2018-02-01

The crude palm oil industry is an agro-industrial commodity. The global market of this industry has experienced rapid growth in recent years, such that it has a strategic value to be developed for Indonesian economy. Despite these economic benefits there are a number of environmental problems at the factories, such as high water consumption, the generation of a large amount of wastewater with a high organic content, and the generation of a large quantity of solid wastes and air pollution. In terms of waste transportation, we propose a multiobjective programming model for managing business environmental risk in a crude palm oil manufacture which gives the best possible configuration of waste management facilities and allocates wastes to these facilities. Then we develop an interactive approach for tackling logistics and environmental risk production planning problem for the crude palm oil industry.

Terahertz time-domain spectroscopy of edible oils

Science.gov (United States)

Dinovitser, Alex; Valchev, Dimitar G.; Abbott, Derek

2017-06-01

Chemical degradation of edible oils has been studied using conventional spectroscopic methods spanning the spectrum from ultraviolet to mid-IR. However, the possibility of morphological changes of oil molecules that can be detected at terahertz frequencies is beginning to receive some attention. Furthermore, the rapidly decreasing cost of this technology and its capability for convenient, in situ measurement of material properties, raises the possibility of monitoring oil during cooking and processing at production facilities, and more generally within the food industry. In this paper, we test the hypothesis that oil undergoes chemical and physical changes when heated above the smoke point, which can be detected in the 0.05-2 THz spectral range, measured using the conventional terahertz time-domain spectroscopy technique. The measurements demonstrate a null result in that there is no significant change in the spectra of terahertz optical parameters after heating above the smoke point for 5 min.

Gas processing at DOE nuclear facilities

Energy Technology Data Exchange (ETDEWEB)

Jacox, J.

1995-02-01

The term {open_quotes}Gas Processing{close_quotes} has many possible meanings and understandings. In this paper, and panel, we will be using it to generally mean the treatment of gas by methods other than those common to HVAC and Nuclear Air Treatment. This is only a working guideline not a rigorous definition. Whether a rigorous definition is desirable, or even possible is a question for some other forum. Here we will be discussing the practical aspects of what {open_quotes}Gas Processing{close_quotes} includes and how existing Codes, Standards and industry experience can, and should, apply to DOE and NRC Licensed facilities. A major impediment to use of the best engineering and technology in many nuclear facilities is the administrative mandate that only systems and equipment that meet specified {open_quotes}nuclear{close_quotes} documents are permissible. This paper will highlight some of the limitations created by this approach.

A comparison of visual observations of surface oil with Synthetic Aperture Radar imagery of the Sea Empress oil spill

Energy Technology Data Exchange (ETDEWEB)

Jones, B.

2001-06-15

A comparison has been made between the visual observations of surface oil and four satellite-borne Synthetic Aperture Radar (SAR) images taken during the Sea Empress oil spill in February 1996. Whilst the basic oil slick imaging capabilities of SAR are well documented, to be of use at the time of a major oil spill, the imagery must be able to provide information on the thickness of oil. This analysis suggests that, under certain environmental conditions, this is possible. The optimum wind speed for the identification of heavy surface oil is around 5-6 m s{sup -1}. At this wind speed, light and medium sheen is not evident in the imagery and there is a distinction between the backscatter reductions due to heavy sheen and thick brown/black oil. At higher wind speeds, even thick oil slicks readily mix into the water column and their SAR signature weakens. In light winds, pattern recognition is very important to the identification of oil sticks. The images are more sensitive to the presence of sheen within the sheltered waters of Milford Haven than in the open coastal waters, indicating a possible relationship between sheen visibility in satellite-borne SAR and sea state. (author)

Environmental effects of acute oil spills. Marine environment

International Nuclear Information System (INIS)

Moe, K.A.; Lystad, E.; Nesse, S.; Selvik, J.R.

1993-01-01

Biological effects as result of acute oil spill pollution may be considered as a product of: the existing biophysical conditions; occurrence and appearance of organisms in time and space; the fate of the oil in time and space; the vulnerability of the various organisms for oil and oil derivatives in a three-dimensional perspective. In general, it seems as every individual oil spill has its own nature and dynamics, inter alia because the physical, chemical and biological conditions never are the same. This means that the properties of the recipients often are more important than the amount of oil that is spilled. This may be exemplified by two oil spills in recent time. Exxon Valdez (1989), where 35000 ton oil were released in a partly closed sea area, caused considerable effects. From Braer (1993) the double amount of oil was spilled, but in an open sea area and at a time where the presence of dense concentrations of environmental components was limited, and the physical conditions favorable with respect to evaporation and dilution. Preliminary results show that the environmental effects were very limited. 311 refs., 32 figs., 10 tabs

Call for information on coastal energy facility siting: an analysis of responses

International Nuclear Information System (INIS)

Anon.

1977-01-01

The Call for Information issued by the New Jersey Department of Environmental Protection in December 1975 consisted of an eight page questionnaire which was sent to industries, government agencies, and private organizations. Its objective was to seek the help of these groups in plans for the siting of energy facilities in the coastal zone. Potential development of oil and gas from the Baltimore Canyon region adjacent to New Jersey has made planning for energy facilities a priority issue both at the state and federal level. The Call for Information invited government and the energy industry to submit (a) suggested criteria for locating energy and energy-related facilities within the New Jersey coastal zone, (b) analyses by governmental and private agencies or groups of the need to locate energy facilities in specific sites within New Jersey's coastal zone, or in generalized portions thereof, and (c) identification of the land-use parameters, appropriate to the various types of facilities which may be proposed, now or later, for coastal siting. The findings obtained from the draft call and the final call issued seven months later are presented. The results of the industries' responses show that the electric and gas utilities gave some useful information while this was true of only a few of the oil companies. The reluctance to give informatign was perhaps aggravated by lack of clear state and federal policies. The appendices illustrate specific information on manpower, cost and facility requirements to develop oil refineries, establish a gas processing plant as well as information from the US Coast Guard and the Environmental Protection Agency. There is also a listing of the companies that bid in the August 1976 lease sale indicating which bids were accepted, a map of the offshore tracts, and a list of which companies responded to the Call for Information

Application of the High Temperature Gas Cooled Reactor to oil shale recovery

International Nuclear Information System (INIS)

Wadekamper, D.C.; Arcilla, N.T.; Impellezzeri, J.R.; Taylor, I.N.

1983-01-01

Current oil shale recovery processes combust some portion of the products to provide energy for the recovery process. In an attempt to maximize the petroleum products produced during recovery, the potentials for substituting nuclear process heat for energy generated by combustion of petroleum were evaluated. Twelve oil shale recovery processes were reviewed and their potentials for application of nuclear process heat assessed. The High Temperature Gas Cooled Reactor-Reformer/Thermochemical Pipeline (HTGR-R/TCP) was selected for interfacing process heat technology with selected oil shale recovery processes. Utilization of these coupling concepts increases the shale oil product output of a conventional recovery facility from 6 to 30 percent with the same raw shale feed rate. An additional benefit of the HTGR-R/TCP system was up to an 80 percent decrease in emission levels. A detailed coupling design for a typical counter gravity feed indirect heated retorting and upgrading process were described. Economic comparisons prepared by Bechtel Group Incorporated for both the conventional and HTGR-R/TCP recovery facility were summarized

Estimating the Life Expectancy of Facilities

Science.gov (United States)

1974-04-01

44160 Radioactive Storage Warehouse 44180 Open Warehouse Facility 44181 Vehicle Storage Facility 44190 Storage-Covered-Depot and Arsenal--Other 44210...state is 23 23, 14 O0 14 9 224 .467 .400 .133 .6w .,determined in the form of the observation matrix: 67 0 12J 3 2 . 5 V = lyr Dta PoitS Dta Polut 6V 1

contractual agreements in ghana's oil and gas industry

African Journals Online (AJOL)

RAYAN_

burden and loss in the event that commercial reserves are not discovered during the period of ... and technical services for the exploration and production of oil.13. In this .... to assess the offices, installations and structural facilities for audit in.

Oil spill prevention: Regulatory trends and compliance at existing storage terminals and refineries

International Nuclear Information System (INIS)

Janisz, A.J.

1993-01-01

In 1973, the Spill Prevention, Control, and Countermeasure (SPCC) regulations were promulgated. The objective of the regulations was to prevent oil spills. However, in the late 1980s and early 1990s, several catastrophic spills of oils led to review of oil spill prevention regulations by the U.S. Environmental Protection Agency, the US Coast Guard, and the Department of the Interior's Minerals Management Service. The reviews led to promulgation of various acts and regulations including the proposed revisions to the SPCC regulations, the Oil Pollution Act of 1990 (OPA-90), and others. Numerous facilities within the petroleum and chemical industry were or will be affected by these regulations. This paper discusses regulatory trends for spill planning and prevention in general, but principally concentrates on above ground storage tanks at facilities storing or refining petroleum products. The paper includes discussions of bills on above ground storage tanks and proposed national standards, as well as regulatory trends in various states. Proposed SPCC regulations and their effects on the industry are also discussed, including requirements for impermeable surfaces and increasing secondary containment capacity. Management strategies to review facility operations and prepare for upgrades are outlined. The paper discusses the types of upgrades typically necessary at existing storage terminals and refineries and discusses information necessary to prepare conceptual designs and cost estimates. Cost estimates for typical upgrades, such as raising earthen berms and installing isolation valves, are presented. Facilities in the state of New Jersey are used as examples, because regulations in New Jersey are similar to the proposed federal regulations

Map of gas facilities and operators in Northeast British Columbia

Energy Technology Data Exchange (ETDEWEB)

Anon.

2005-06-01

This map represents 57 gas facilities and operators and references location on the map to the facility and operator. The Northern Rockies Regional district is indicated, as is the Peace River Regional district. Roads, truck trails, railroads, pipeline and airstrips are indicated as well as oil and gas fields. Various protected areas and First Nations settlement areas and regions are also indicated. The following companies placed advertisements on the map, detailing the services they provide: Wellco Energy Services; C.E. Franklin Ltd.; the City of Fort St. John, Region of Chetwynd; Smith Bits; the City of Dawson Creek, Economic Development and Tourism; Fort Nelson and Northern Rockies Regional District; Pipetech Corp.; Kenwood; Hughes Christensen; Spartan Controls; FI Canada Oil Services Ltd.; Northstar Drillstem Testers Inc.; Rainbow Transport Ltd.1 fig.

75 FR 63093 - Oil Pollution Prevention; Spill Prevention, Control, and Countermeasure (SPCC) Rule-Compliance...

Science.gov (United States)

2010-10-14

... Oil Pollution Prevention; Spill Prevention, Control, and Countermeasure (SPCC) Rule--Compliance Date... certain facilities must prepare or amend their Spill Prevention, Control, and Countermeasure (SPCC) Plans... facilities must prepare or amend their Spill Prevention, Control, and Countermeasure (SPCC) Plans (or ``Plan...

Alberta Oil Sands Equity annual report, 1991-92. Partnership and progress in Alberta's oil sands development

International Nuclear Information System (INIS)

1992-01-01

Alberta Oil Sands Equity (AOSE) manages the Alberta government's equity investments in oil sands and heavy oil projects. AOSE is a 16.74% participant in the Syncrude Project, a 10% participant in the OSLO (Other Six Leases Operation) Commercial Project and the OSLO New Ventures project, and a 24.17% participant in the Lloydminster Bi-Provincial Upgrader. Syncrude produces over 11% of Canadian crude oil requirements, and AOSE's share yielded $43.3 million profit for 1991/92, down significantly from the $82.1 million the previous year due to lower oil prices. The OSLO Commercial Project is a proposed commercial oil sands plant with a mine site and extraction plant to be located north of Fort McMurray, and an upgrading facility to be situated north of Edmonton. Work on this project was suspended in early 1992. The OSLO New Ventures project will handle the exploration and development of the remaining five oil sands leases plus the southern portion of Lease 31. As of March 31, 1992, the project owners were considering a commercial demonstration project utilizing dredging and cold-water extraction processes. Two of the owners are unable to provide funding and discussions are under way to resolve the matter and move the program forward. The Lloydminster Bi-Provincial Upgrader was nearly 90% complete in March 1992 and full startup is expected in November 1992; engineering work was completed in March 1991. The upgrader will increase the value of heavy crude oil and thereby increase its demand. 4 figs., 4 tabs

Millennium Open Pit Mine, Alberta, Canada

Science.gov (United States)

2007-01-01

Near Fort McMurray, Alberta, Canada, on the east bank of the Athabasca River, are found the Steepbank and Millennium mines. These open pit mines produce oil sands that are processed to recover bitumen, and then upgrade it to refinery-ready raw crude oil, and diesel fuel. The ASTER images were acquired September 22, 2000 and July 31, 2007, cover an area of 22.5 x 25.5 km, and are located near 57 degrees north latitude, 111.5 degrees west longitude. The U.S. science team is located at NASA's Jet Propulsion Laboratory, Pasadena, Calif. The Terra mission is part of NASA's Science Mission Directorate.

Floated oil is separated and is recovered; Fujoyu wo bunri{center_dot}kaishu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

The Nisseki MITSUBISHI developed the separation of the oil of the oiliness cutting oil which arose by machine tools, etc. in Kowa Mtech and cooperation jointly with recovery equipment. The same equipment is made to be sales promotion tool of the lubricating oil in the name of [YUNI-CLEAN] and the sole agent sells the Nisseki MITSUBISHI. The price is opened. The result of using the same equipment for besides the recovery of contamination oil which accumulates in tanks such as the machine tool using water-soluble lubricating oil recovery of floated oil of oil separating tank of the waste water treatment process, etc.. (translated by NEDO)

Chronic oiling and long-term effects of the 1986 Galeta spill on fringing mangroves

International Nuclear Information System (INIS)

Garrity, S.D.; Levings, S.C.; Burns, K.A.

1993-01-01

In April 1986, more than 50,000 barrels of crude oil spilled into Bahia las Minas on the central Caribbean coast of Panama, oiling reef flats, sea grasses, coral reefs and mangroves. In August 1986, the authors began a five-year study on the red mangrove (Rhizophora mangle L.) fringe and the plants and animals that live attached to submerged prop roots. This habitat forms an important part of near shore, tropical nursery grounds. In three habitats (wave-washed open shores, channels and lagoons, and interior drainage streams), oil initially coated virtually the entire surface of submerged prop roots and sank more than 20 cm into sediments. Secondary re-oiling was heaviest in sheltered drainage streams where oil continuously leached from sediments, but also occurred on the open coast and in channels. Bivalves in channels and streams were heavily contaminated through at least May 1991. Results show this spill was a chronic source of oil contamination rather than a single point-source event. The epibiota of submerged mangrove roots had not recovered completely in any habitat after five years. Independent of this reduction, the structure of the mangrove fringe significantly changed after oiling, including decreases in the amount of shore fringed with mangroves and in the density and size of submerged prop roots. Overall, the surface area on submerged mangrove roots decreased by 33 percent on the open coast, 38 percent in channels and 74 percent in stream. The combination of chronic re-oiling, damage to epibiotic assemblages, and reductions in the biogenic substrate (submerged prop roots) has decreased the productivity of this tropical nursery area and suggests recovery will be a complex and prolonged process

Evaluation of renewable energy alternatives for highway maintenance facilities.

Science.gov (United States)

2013-12-01

A considerable annual energy budget is used for heating, lighting, cooling and operating ODOT : maintenance facilities. Such facilities contain vehicle repair and garage bays, which are large open : spaces with high heating demand in winter. The main...

Neoplastic changes in freshwater fishes: Correlation with oil refining

International Nuclear Information System (INIS)

Ostrander, G.K.

1993-01-01

Traditionally, oil pollution has been viewed as single event, large scale disasters such as the Exxon Valdez spill in Alaska. However, it is becoming increasingly apparent that by products and anthropogenic contaminants resulting from oil exploration, extraction, recovery, refining, and the manufacture and use of oil and oil-based products are negatively impacting the environment. Potential problems of freshwater pollution by oil contaminants are increasing in many parts of the world from both active and abandoned oil production facilities. In the USA many ''Superfund'' sites have been designated for cleanup under the Comprehensive Environmental Response, Compensation and Liability Act of 1980; primarily because of waste discharged on to the sites by the oil industry. Pollution of surface and groundwater from these sites has already occurred and in some cases has led to deleterious effects on the complex aquatic and terrestrial ecosystems on and near these sites. The effect of oil and oil related products on aquatic organisms will be reviewed. Specifically, the discussion will focus on preneoplastic and neoplastic changes in fishes with a primary endpoint of cancer. Finally, a summary of current studies of feral fishes residing on and near an abandoned oil refinery in Oklahoma will be presented

Facile one-pot synthesis of gold and silver nanocatalysts using edible coconut oil

Science.gov (United States)

Meena Kumari, M.; Philip, Daizy

2013-07-01

The use of edible oil for the synthesis of metal nanoparticles by wet chemical method is reported for the first time. The paper presents an environmentally benign bottom up approach for the synthesis of gold and silver nanoparticles using edible coconut oil at 373 K. The formation of silver nanoparticles is signaled by the brownish yellow color and that of gold nanoparticles by the purple color. Fine control over the nanoparticle size and shape from triangular to nearly spherical is achieved by varying the quantity of coconut oil. The nanoparticles have been characterized by UV-Visible, Transmission Electron Microscopy and X-ray Diffraction. The chemical interaction of capping agents with metal nanoparticles is manifested using Fourier Transform Infrared Spectroscopy. The stable and crystalline nanoparticles obtained using this simple method show remarkable size-dependent catalytic activity in the reduction of the cationic dye methylene blue (MB) to leuco methylene blue (LMB). The first order rate constants calculated uphold the size dependent catalytic activity of the synthesized nanoparticles.

Prospects for non-OPEC oil supply

International Nuclear Information System (INIS)

O'Dell, S.

1994-01-01

An International Energy Agency forecast is provided of non-OPEC oil production over a 15-year horizon. Reference-case forecasts are derived from Hubbert-type resource models, official industry announcements about such matters as oil discoveries and development projects, and an oil industry consensus. Separate regional profiles are provided for North America, Europe, the former Soviet Union, and the rest of non-OPEC countries (South America, Asia, non-OPEC Middle East). Under a flat-price scenario ($18/bbl), total non-OPEC oil supply rises slightly from 41.4 million bbl/d (MBD) in 1995 to 41.9 MBD in 2010. Under a scenario in which prices rise to $28/bbl, oil supply rises to 47.5 MBD in 2010. The latter results depend on specific assumptions concerning economic growth, energy prices, the geological potential of some areas which are not yet well understood, technological advances, and the nature of political developments. Uncertainties regarding these assumptions are discussed, with reference to reserves, price responsiveness, world oil industry investment, technology, and costs. A major uncertainty is the issue of investment in the OPEC countries, since the rising-price scenario assumes that OPEC invests only reluctantly. If major OPEC producers choose to open their upstream sectors to international oil companies, the situation will change completely. Otherwise, oil markets are expected to continue to behave in the manner of the past 20 years, with highest-cost oil being developed first while cheaper oil remains in the ground. 8 refs., 10 figs., 3 tabs

Profiler : Canadian oil and gas : the First Nations : building successful partnerships

Energy Technology Data Exchange (ETDEWEB)

Anon.

2010-05-15

Canada's petroleum and natural gas is often produced in remote areas where the majority of the population is Aboriginal. Many First Nations and Metis communities are now playing an active role in Canada's oil and gas industry. Aboriginal-owned companies have earned more than $2.6 billion in the oil sands region since 1999. In 2007, the value of contracts between Alberta oil sands companies and Aboriginal companies was estimated at $606 million. This special supplement discussed First Nations partnerships in the oil and gas industry. Articles in the supplement presented new employment, training and partnership activities in the oil and gas industry as well as activities related to emerging unconventional resources. Educational programs and training facilities were described. The employment and procurement practices of leading oil and gas operators were discussed. The supplement featured presentations by several leading oil and gas companies. tabs., figs.

Canada's east coast offshore oil and gas industry: a backgrounder

International Nuclear Information System (INIS)

Bott, R.

1999-06-01

Another of the backgrounder series published by the Petroleum Communication Foundation, this booklet describes Canada's offshore oil and natural gas operations in the North Atlantic Ocean, specifically in the Hibernia (off Newfoundland, crude oil), Terra Nova (off Newfoundland, crude oil), Cohasset-Panuke (off Nova Scotia, crude oil) and Sable Island (off Nova Scotia, natural gas) fields. Together, these project represent an investment of more than 10 billion dollars and constitute a growing portion of Canada's 400,000 cubic metres of crude oil and natural gas liquids per day production. The booklet explains the importance of the offshore oil and natural gas industry to Canada, the benefits accruing to the maritime provinces locally, prospects for future offshore oil and natural gas development and provides a brief summary of each of the four current major projects. The booklet also provides an overview of the facilities required for offshore energy projects, environmental impacts and safeguards, exploration, drilling, production, processing and transportation aspects of offshore oil and gas projects. 9 refs, photos

Oil and Gas Emergency Policy: China 2012 update

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-09-06

Although coal is the dominant energy source in China, accounting for some 70% of the country's Total Energy Consumption (TEC) in 2009, oil and gas are also essential energy sources. Despite strong growth in consumption of oil, its share of TEC fell from 22% in 2000 to 18% in 2009, as coal use rose even faster to meet burgeoning demand for electricity. A strong policy push boosted natural gas supplies, particularly to residential customers, so that the share of natural gas doubled from 2% in 2000 to 4% in 2009. China is one of the important oil and natural gas producing counties in the world. In 2010, China's crude oil production exceeded 4 million barrels per day (mb/d). However, with strong and sustained economic growth, its demand for oil has also increased, from 4.6 mb/d in 2000 to over 8 mb/d in 2009. In the New Policy Scenario (NPS) of the IEA World Energy Outlook (WEO) 2011, China's primary oil demand rises to 12.2 mb/d in 2020. Although China is now the world's fifth largest oil producer, the country has been a net oil importer since 1993. In 2011, China imported over 5 mb/d of crude oil, accounting for about 54% of its total demand. More than 50% of the total crude oil imports came from counties of the Middle East. To prevent a potential shock to the economy caused by an oil supply disruption, the Chinese government has been steadily pushing building an oil stock reserve system. China has completed four stockpiling facilities with a capacity of around 103 mb in the first phase of its Strategic Petroleum Reserve (SPR) plan, and has begun construction of its second phase, which comprises eight storage sites that will reportedly have a combined capacity of around 207 mb. Among them, two sites were completed in the second half of 2011 and the Tianjin site is reportedly set to be completed in 2012. According to unofficial reports, the remaining four SPR-II sites are expected to become operational by 2013. The third phase is expected to boost

Application of ultraviolet fluorometry and excitation-emission matrix spectroscopy (EEMS) to fingerprint oil and chemically dispersed oil in seawater.

Science.gov (United States)

Bugden, J B C; Yeung, C W; Kepkay, P E; Lee, K

2008-04-01

Excitation-emission matrix spectroscopy (EEMS) was used to characterize the ultra violet fluorescence fingerprints of eight crude oils (with a 14,470-fold range of dynamic viscosity) in seawater. When the chemical dispersant Corexit 9500 was mixed with the oils prior to their dispersion in seawater, the fingerprints of each oil changed primarily as an increase in fluorescence over an emission band centered on 445 nm. In order to simplify the wealth of information available in the excitation-emission matrix spectra (EEMs), two ratios were calculated. A 66-90% decrease in the slope ratio was observed with the addition of Corexit. When the slope ratios were reduced in complexity to intensity ratios, similar trends were apparent. As a result either of the ratios could be used as a simple and rapid means of identifying and monitoring chemically dispersed oil in the open ocean.

Inspired by Stenocara Beetles: From Water Collection to High-Efficiency Water-in-Oil Emulsion Separation.

Science.gov (United States)

Zeng, Xinjuan; Qian, Long; Yuan, Xianxia; Zhou, Cailong; Li, Zhaowen; Cheng, Jiang; Xu, Shouping; Wang, Shuangfeng; Pi, Pihui; Wen, Xiufang

2017-01-24

Inspired by the water-collecting mechanism of the Stenocara beetle's back structure, we prepared a superhydrophilic bumps-superhydrophobic/superoleophilic stainless steel mesh (SBS-SSM) filter via a facile and environmentally friendly method. Specifically, hydrophilic silica microparticles are assembled on the as-cleaned stainless steel mesh surface, followed by further spin-coating with a fluoropolymer/SiO 2 nanoparticle solution. On the special surface of SBS-SSM, attributed to the steep surface energy gradient, the superhydrophilic bumps (hydrophilic silica microparticles) are able to capture emulsified water droplets and collect water from the emulsion even when their size is smaller than the pore size of the stainless steel mesh. The oil portion of the water-in-oil emulsion therefore permeates through pores of the superhydrophobic/superoleophilic mesh coating freely and gets purified. We demonstrated an oil recovery purity up to 99.95 wt % for surfactant-stabilized water-in-oil emulsions on the biomimetic SBS-SSM filter, which is superior to that of the traditional superhydrophobic/superoleophilic stainless steel mesh (S-SSM) filter lacking the superhydrophilic bump structure. Together with a facile and environmentally friendly coating strategy, this tool shows great application potential for water-in-oil emulsion separation and oil purification.

Disposal/recovery options for brine waters from oil and gas production in New York State. Final report

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, M.R.; Atkinson, J.F.; Bunn, M.D.; Hodge, D.S.

1996-03-01

Produced water from oil and gas operations, or brine as it is typically referred, may be characterized as being highly saline, with total dissolved solids greater than 100 g/L. If these bribes are disposed improperly there may be severe adverse environmental effects. Thus, it is important that brine be disposed using environmentally sound methods. Unfortunately, costs for the disposal of brine water are a significant burden to oil and gas producers in New York State. These costs and the relatively low market price of oil and natural gas have contributed to the decline in gas and oil production in New York State during the past 10 years. The objectives of this study were to evaluate new and existing options for brine disposal in New York State, examine the technical and economic merits of these options, and assess environmental impacts associated with each option. Two new disposal options investigated for New York State oil and gas producers included construction of a regional brine treatment facility to treat brine prior to discharge into a receiving water and a salt production facility that utilizes produced water as a feed stock. Both options are technically feasible; however, their economic viability depends on facility size and volume of brine treated.

Disposal/recovery options for brine waters from oil and gas production in New York State. Final report

International Nuclear Information System (INIS)

Matsumoto, M.R.; Atkinson, J.F.; Bunn, M.D.; Hodge, D.S.

1996-03-01

Produced water from oil and gas operations, or brine as it is typically referred, may be characterized as being highly saline, with total dissolved solids greater than 100 g/L. If these bribes are disposed improperly there may be severe adverse environmental effects. Thus, it is important that brine be disposed using environmentally sound methods. Unfortunately, costs for the disposal of brine water are a significant burden to oil and gas producers in New York State. These costs and the relatively low market price of oil and natural gas have contributed to the decline in gas and oil production in New York State during the past 10 years. The objectives of this study were to evaluate new and existing options for brine disposal in New York State, examine the technical and economic merits of these options, and assess environmental impacts associated with each option. Two new disposal options investigated for New York State oil and gas producers included construction of a regional brine treatment facility to treat brine prior to discharge into a receiving water and a salt production facility that utilizes produced water as a feed stock. Both options are technically feasible; however, their economic viability depends on facility size and volume of brine treated

Minimal incorporation of Deepwater Horizon oil by estuarine filter feeders

International Nuclear Information System (INIS)

Fry, Brian; Anderson, Laurie C.

2014-01-01

Highlights: • Oil from the Deepwater Horizon oil spill entered Louisiana bays in mid-2010. • Oil was used minimally (<1%) in diets of mussels and barnacles. • Also, oil did not enhance planktonic respiration rates. • Use of oil carbon was relatively small in these productive estuarine food webs. - Abstract: Natural abundance carbon isotope analyses are sensitive tracers for fates and use of oil in aquatic environments. Use of oil carbon in estuarine food webs should lead to isotope values approaching those of oil itself, −27‰ for stable carbon isotopes reflecting oil origins and −1000‰ for carbon-14 reflecting oil age. To test for transfer of oil from the 2010 Deepwater Horizon spill into estuarine food webs, filter-feeding barnacles (Balanus sp.) and marsh mussels (Geukensia demissa) were collected from Louisiana estuaries near the site of the oil spill. Carbon-14 analyses of these animals from open waters and oiled marshes showed that oil use was <1% and near detection limits estimated at 0.3% oil incorporation. Respiration studies showed no evidence for enhanced microbial activity in bay waters. Results are consistent with low dietary impacts of oil for filter feeders and little overall impact on respiration in the productive Louisiana estuarine systems

Commentary: open access, open business, closed fairness!

Science.gov (United States)

Moustafa, Khaled

2015-01-01

A strong trend to move from print to online publication is largely perceived in scientific and nonscientific fields. A growing number of publishers increasingly opt for online publication as an option or a compulsory alternative. From readers' perspective, this is a highly appreciated facility, but from the author's, things are different mainly because of excessive article processing charges (APC) that make the open access system sometimes as a hindrance for many authors but a lucrative enterprise for many shareholders, enticing the most traditional and conservative publishers.

Oil Motion Control by an Extra Pinning Structure in Electro-Fluidic Display.

Science.gov (United States)

Dou, Yingying; Tang, Biao; Groenewold, Jan; Li, Fahong; Yue, Qiao; Zhou, Rui; Li, Hui; Shui, Lingling; Henzen, Alex; Zhou, Guofu

2018-04-06

Oil motion control is the key for the optical performance of electro-fluidic displays (EFD). In this paper, we introduced an extra pinning structure (EPS) into the EFD pixel to control the oil motion inside for the first time. The pinning structure canbe fabricated together with the pixel wall by a one-step lithography process. The effect of the relative location of the EPS in pixels on the oil motion was studied by a series of optoelectronic measurements. EPS showed good control of oil rupture position. The properly located EPS effectively guided the oil contraction direction, significantly accelerated switching on process, and suppressed oil overflow, without declining in aperture ratio. An asymmetrically designed EPS off the diagonal is recommended. This study provides a novel and facile way for oil motion control within an EFD pixel in both direction and timescale.

Biodiesel production from vegetable oil: Process design, evaluation and optimization

Directory of Open Access Journals (Sweden)

Kianimanesh Hamid Reza

2017-09-01

Full Text Available To investigate the effect of reactor performance/configuration of biodiesel production on process parameters (mass & energy consumption, required facilities etc., two diverse production processes (from vegetable oil were implemented/designed using Aspen HYSYS V7.2. Two series reactors were taken into account where overall conversion was set to be 97.7% and 70% in first and second processes respectively. Comparative analysis showed that an increase in conversion yield caused to consumption reduction of oil, methanol, cold energy and hot energy up to 9.1%, 22%, 67.16% and 60.28% respectively; further, a number of facilities (e.g. boiler, heat exchanger, distillation tower were reduced. To reduce mass & energy consumption, mass/heat integration method was employed. Applying integration method showed that in the first design, methanol, cold and hot energy were decreased by 49.81%, 17.46% and 36.17% respectively; while in the second design, oil, methanol, cold and hot energy were decreased by 9%, 60.57% 19.62% and 36.58% respectively.

GEO-ECOLOGICAL PECULIARITIES OF ENVIRONMENTAL POLLUTION WITH OIL PRODUCTS EMITTED BY RAILROAD FACILITIES

Directory of Open Access Journals (Sweden)

Senyushchenkova Irina Mikhaylovna

2012-10-01

Full Text Available Linear railroad facilities have been producing an adverse impact on the environment by polluting it with oil products for an extensive period of time. The authors of the article consider several mechanisms of contamination and the pattern of its spread into soils. Currently, areas that used to be unsuitable for development as urban lands for geological or environmental reasons are now being intensively developed. The study is exemplified by a city outstretched onto the complex terrain. Complex topography contemplates geological, tectonics-related, hydrological conditions, exogenous processes and anthropogenic factors. In this connection, the main purpose of the study is to analyze the geo-ecological factors that impact urban lands in complex geo-morphological conditions with a view to their functional use against minimal environmental risks to assure the most favorable conditions for humans. Towards this end, the authors have applied the following theoretical and practical methods of research, including a pilot study, namely (1 the geomorphological analysis of urban lands, (2 the monitoring and analysis of the anthropogenic impact produced onto various constituents of the environment, and (3 development of methods of functional use of urban lands in complex geomorphological conditions. The authors have monitored contaminated lands to develop their recommendations for their development in complex geomorphological conditions, namely: 1. Urban development planning should be performed with consideration for the geomorphological elements taken as a whole, as they are closely connected to one another. 2. Selection of methods of rehabilitation of urban lands must be preceded by the zoning of the territory based on its geological and environmental properties.

Challenges for proteomics core facilities.

Science.gov (United States)

Lilley, Kathryn S; Deery, Michael J; Gatto, Laurent

2011-03-01

Many analytical techniques have been executed by core facilities established within academic, pharmaceutical and other industrial institutions. The centralization of such facilities ensures a level of expertise and hardware which often cannot be supported by individual laboratories. The establishment of a core facility thus makes the technology available for multiple researchers in the same institution. Often, the services within the core facility are also opened out to researchers from other institutions, frequently with a fee being levied for the service provided. In the 1990s, with the onset of the age of genomics, there was an abundance of DNA analysis facilities, many of which have since disappeared from institutions and are now available through commercial sources. Ten years on, as proteomics was beginning to be utilized by many researchers, this technology found itself an ideal candidate for being placed within a core facility. We discuss what in our view are the daily challenges of proteomics core facilities. We also examine the potential unmet needs of the proteomics core facility that may also be applicable to proteomics laboratories which do not function as core facilities. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Novel Bioplastics and biocomposites from Vegetable Oils

Energy Technology Data Exchange (ETDEWEB)

Henna, Phillip H. [Iowa State Univ., Ames, IA (United States)

2008-01-01

there are three degrees of unsaturation. In addition, the double bonds are not in conjugation. Table 1 gives the fatty acid make-up of linseed oil. It can be seen that linseed oil has an average of 6.0 double bonds per triglyceride. Its fatty acid content consists of 5.4% palmitic acid (C16:0), 3.5% stearic acid (C18:0), 19% oleic acid (C18:1), 24 % linoleic acid (C18:2) and 47% linolenic (C18:3). Table 1 also gives the fatty acid composition and varying degrees of unsaturation for various other naturally-occurring natural vegetable oils. The regions of unsaturation in natural oils allow for interesting polymer chemistry to take place. Some of this interesting polymer science, however, involves chemical modification of the regions of unsaturation. Acrylated epoxidized soybean oil (AESO) is prepared by epoxidation of the double bonds, followed by ring opening with acrylic acid. The resulting oil has both acrylate groups and hydroxyl groups. Wool and colleagues have further reacted the hydroxyl groups within the oil with maleic anhydride to produce maleated acrylated epoxidized soybean oil (MAESO). The MAESO has been copolymerized with styrene free radically to produce promising thermosetting sheet molding resins. Petrovi? and co-workers have directly ring opened the epoxidized oil to produce polyols that produce promising polyurethanes through condensation polymerization with diisocyanates. Our group's work initially focused on direct cationic copolymerization of the double bonds or conjugated double bonds of natural oils with monomers, such as styrene and divinylbenzene, to produce promising thermosetting resins. The only modification of the oils that was carried out in these studies was conjugation of the double bonds to enhance the reactivity of the oil. This work has been expanded recently with the incorporation of glass fiber to produce promising composites. We have also explored thermal polymerization techniques to make novel thermosets. This dissertation is

RELIABILITY MODELING BASED ON INCOMPLETE DATA: OIL PUMP APPLICATION

Directory of Open Access Journals (Sweden)

Ahmed HAFAIFA

2014-07-01

Full Text Available The reliability analysis for industrial maintenance is now increasingly demanded by the industrialists in the world. Indeed, the modern manufacturing facilities are equipped by data acquisition and monitoring system, these systems generates a large volume of data. These data can be used to infer future decisions affecting the health facilities. These data can be used to infer future decisions affecting the state of the exploited equipment. However, in most practical cases the data used in reliability modelling are incomplete or not reliable. In this context, to analyze the reliability of an oil pump, this work proposes to examine and treat the incomplete, incorrect or aberrant data to the reliability modeling of an oil pump. The objective of this paper is to propose a suitable methodology for replacing the incomplete data using a regression method.

A versatile route to hybrid open-framework materials | Ayi | Global ...

African Journals Online (AJOL)

The isolation of the intermediate phase and its reaction with metal ions to form open framework solids has been explored and it has proven a facile route of synthesizing inorganic-organic hybrid materials with open pores. Here the amine phosphate route of templating inorganic open-framework materials has been reviewed ...

Evaluating Past and Future USCG Use of Ohmsett Test Facility

Science.gov (United States)

2016-10-01

of Pages 22 22. Price Evaluating Past and Future USCG Use of Ohmsett Test Facility iv UNCLAS//Public | | CG-926 RDC | M. Fitzpatrick, et al...Opportunity Skimming System WEC Wave energy converter Evaluating Past and Future USCG Use of Ohmsett Test Facility x UNCLAS//Public | | CG-926 RDC | M...Date Summary of Effort OCT-NOV 1993 Vessel of Opportunity Skimming System (VOSS) (5 Weeks) APR-JUN 1996 Spilled Oil Recovery System (SORS) (8 Weeks

Bioremediation of oil contaminated soils

International Nuclear Information System (INIS)

Beeson, D.L.; Hogue, J.I.; Peterson, J.C.; Guerra, G.W.

1994-01-01

The Baldwin Waste Oil Site was an abandoned waste oil recycling facility located in Robstown, Nueces County, Texas. As part of their site assessment activities, the US Environmental Protection Agency (EPA) requested that the Ecology and Environment, Inc., Technical Assistance Team (TAT) investigate the feasibility of using in-situ bioremediation to remediate soils contaminated with oil and grease components, petroleum hydrocarbons, and volatile organic compounds. Bioremediation based on the land treatment concept was tested. The land treatment concept uses techniques to optimize indigenous microbial populations and bring them in contact with the contaminants. The study was designed to collect data upon which to base conclusions on the effectiveness of bioremediation, to demonstrate the effectiveness of bioremediation under field conditions, and to identify potential problems in implementing a full-scale project. Bioremediation effectiveness was monitored through total petroleum hydrocarbons (TPH) and Oil and Grease (O and G) analyses. Site specific treatment goals for the pilot project were concentrations of less than 1% for O and G and less than 10,000 mg/kg for TPH. Based on the reduction of TPH and O and G concentrations and the cost effectiveness of bioremediation based on the land treatment concept, full-scale in-situ bioremediation was initiated by the EPA at the Baldwin Waste Oil Site in February of 1993

Decommissioning end of life oilfield facilities and pipelines : the first step to the safe and efficient remediation of oil and gas sites

International Nuclear Information System (INIS)

Kitchen, J.; Thygesen, S.

2005-01-01

Environmentally sound decommissioning practices in the remediation and reclamation process were reviewed, with reference to abandoned oil and gas facilities and pipelines. There are inherent dangers associated with aged infrastructure, and decommissioning companies should be the first service on site to ensure that all facilities have been located, removed and cleaned. All licensed, unlicensed and on-lease pipelines are required to be properly abandoned. Site research is needed to identify any industry or government regulated requirements that may impact the decommissioning process. Decommissioning companies are also responsible for recording all relevant site information so that it can be conveyed to remediation and reclamation companies. A knowledge of landowner sensitivities, weather affected access, unlicensed facilities and locations of historic contamination are crucial to all parties involved. Additional documentation, such as photographs and survey drawings, can assist remediation and reclamation companies in locating areas of concern. Once a well has been abandoned in Alberta, surface equipment, cement pads, debris and produced liquids associated with the well license must be removed within 12 months of the cutting and capping operation. Records of the removal and cleanup activities must be retained by the licensee. Many sites have been sitting dormant for several years and can be harboring dangerous production fluids, asbestos, Hantavirus and other hazardous materials. All equipment must be steam-cleaned by qualified personnel and all production fluids and contaminated water from the cleaning process must be captured and transported to a waste facility. All equipment that is deemed re-usable can be returned to inventory or re-used. Equipment that can not be salvaged is sold for recycling at a steel mill. All pipelines are required to be cleaned of hydrocarbons, purged and left with a medium of inert gas or atmospheric air. Residual fluids left in a

Field research on using oil herding surfactants to thicken oil slicks in pack ice for in-situ burning. Volume 1

International Nuclear Information System (INIS)

Buist, I.; Potter, S.; Nedwed, T.; Mullin, J.

2007-01-01

Laboratory and field studies have been performed in recent years to determine the capability of herding agents to thicken oil slicks among loose pack ice for the purpose of in situ burning. In loose pack ice conditions where booms are not practical, effective in situ burns may be possible if thin slicks could be thickened to the 2 to 5 mm range. However, specific chemical surface-active agents known as herders are need to clear and contain oil slicks on an open water surface. The agents spread quickly over a water surface into a monomolecular layer due to their high spreading coefficients. The best agents have spreading pressures in the mid 40 mN/m range. As such, only small quantities of these surfactants are needed to clear thin films of oil from large areas of water surface, and to contract it into thicker slicks. This paper summarized the previous studies that evaluated shoreline-cleaning agents with oil herding properties. However, the main focus of this paper was on the final phase of testing conducted at the Prudhoe Bay Fire Training Grounds in November 2006 in which a series of outdoor burns were conducted at the scale of 30 m 2 with herders and crude oil in a test pool containing pieces of ice. The tests revealed that when a herder was used on crude oil slicks that were otherwise unignitable, the slicks could be ignited and burned in situ in brash and slush ice conditions at temperatures as low as -17 degrees C. Both the removal rate and efficiencies for the herded slicks were comparable to the theoretical maximum achievable for mechanically contained slicks on open water. 13 refs., 1 tab., 18 figs

Geochemical signature of radioactive waste: oil NORM

International Nuclear Information System (INIS)

Costa, Gilberto T. de Paula; Costa-de-Moura, Jorge; Gomes, Carlos de Almeida; Sampaio, Emidio A. Lopes

2017-01-01

The Brazilian Nuclear Agency (CNEN) rules all nuclear activity in Brazil as demanded by the Federal Constitution, articles 21, XXIII, and 177, V, and by the Federal Acts 4.118/62 and 10.308/2001. Therefore, the CNEN is responsible for any radioactive waste disposal in the country. Oil Naturally Occurring Radioactive Materials (Oil NORM) in this paper refers to waste coming from oil exploration. Oil NORM has called much attention during the last decades, mostly because it is not possible to determine its primary source due to the actual absence of regulatory control mechanism. There is no efficient regulatory tool which allows determining the origin of such NORM wastes even among those facilities under regulatory control. This fact may encourage non-authorized radioactive material transportation, smuggling and terrorism. The aim of this project is to provide a geochemical signature for each oil NORM waste using its naturally occurring isotopic composition to identify its origin. The here proposed method is a specific geochemical modeling of oil sludge NORM samples which are analyzed for radioisotopes normally present in oil pipes, such as 228 Ac, 214 Bi and 214 Pb. The activity ratios are plotted in scatter diagrams. This method was successfully tested with data of different sources obtained from analysis reports from the Campos Basin/Brazil and from literature. (author)

Geochemical signature of radioactive waste: oil NORM

Energy Technology Data Exchange (ETDEWEB)

Costa, Gilberto T. de Paula; Costa-de-Moura, Jorge; Gomes, Carlos de Almeida; Sampaio, Emidio A. Lopes, E-mail: gilberto.costa@cnen.gov.br, E-mail: jcmoura@cnen.gov.br, E-mail: cgomes@cnen.gov.br [Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil). Div. de Controle de Rejeitos e Transporte de Materiais Radioativos

2017-07-01

The Brazilian Nuclear Agency (CNEN) rules all nuclear activity in Brazil as demanded by the Federal Constitution, articles 21, XXIII, and 177, V, and by the Federal Acts 4.118/62 and 10.308/2001. Therefore, the CNEN is responsible for any radioactive waste disposal in the country. Oil Naturally Occurring Radioactive Materials (Oil NORM) in this paper refers to waste coming from oil exploration. Oil NORM has called much attention during the last decades, mostly because it is not possible to determine its primary source due to the actual absence of regulatory control mechanism. There is no efficient regulatory tool which allows determining the origin of such NORM wastes even among those facilities under regulatory control. This fact may encourage non-authorized radioactive material transportation, smuggling and terrorism. The aim of this project is to provide a geochemical signature for each oil NORM waste using its naturally occurring isotopic composition to identify its origin. The here proposed method is a specific geochemical modeling of oil sludge NORM samples which are analyzed for radioisotopes normally present in oil pipes, such as {sup 228}Ac, {sup 214}Bi and {sup 214}Pb. The activity ratios are plotted in scatter diagrams. This method was successfully tested with data of different sources obtained from analysis reports from the Campos Basin/Brazil and from literature. (author)

Chinese refining capacity for Canadian heavy oil

International Nuclear Information System (INIS)

Bruce, G.W.

2006-01-01

This paper discussed China's refining capacity in relation to exports of Canadian heavy oil. Demand for oil is increasing throughout the world, and China is expected to consume 25 per cent of the projected yearly oil supplies. Alberta currently has an estimated 174 billion barrels of recoverable bitumen, and produces 1.06 million barrels per day. Production is expected to increase to 4.5 million barrels per day by the year 2020. Currently bitumen blends are refined and diluted with naphtha and sweet synthetic crude oil. Bitumen is a challenging feedstock for refineries, and requires thermal production methods or gasification processes. Primary conversion into sour synthetic crude is typically followed by hydrocracking and further refining into finished petroleum products. There are currently 50 refineries in China with a 7.4 million barrel per day capacity. Coastal refineries using imported crude oil have a 4 million barrel per day capacity. New facilities are being constructed and existing plants are being upgraded in order to process heavier and more sour crude oils. However, current refining capabilities in Chinese refineries have a limited ability for resid conversion. It was concluded that while China has a refining infrastructure, only refineries on the coast will use oil sands-derived feedstocks. However, there are currently opportunities to design refineries to match future feedstocks. tabs., figs

Russia: Privatisation and co-venturing in the Russian oil sector

International Nuclear Information System (INIS)

Sanders, D.; Zverev, A.

1993-01-01

As foreign investment in the Russian oil industry is now being permitted for the first time, many international companies are experiencing difficult and unreceptive conditions. This article suggests that the Russian domestic oil industry must seek to restructure itself in an orderly fashion, so that foreign investors are treated on a rational, open and fair basis. However western oil companies will need, alongside these changes, to invest in existing operations or actively seek the participation of local partners if privatization and co-venturing are to be a success. (UK)

Floating Oil-Spill Containment Device

Science.gov (United States)

Jones, Jack A.

2012-01-01

Previous oil containment booms have an open top that allows natural gas to escape, and have significant oil leakage due to wave action. Also, a subsea pyramid oil trap exists, but cannot move relative to moving oil plumes from deepsea oil leaks. The solution is to have large, moveable oil traps. One version floats on the sea surface and has a flexible tarp cover and a lower weighted skirt to completely entrap the floating oil and natural gas. The device must have at least three sides with boats pulling at each apex, and sonar or other system to track the slowly moving oil plume, so that the boats can properly locate the booms. The oil trap device must also have a means for removal of the oil and the natural gas. A second design version has a flexible pyramid cover that is attached by lines to ballast on the ocean floor. This is similar to fixed, metal pyramid oil capture devices in the Santa Barbara Channel off the coast of California. The ballast lines for the improved design, however, would have winches that can move the pyramid to always be located above the oil and gas plume. A third design is a combination of the first two. It uses a submerged pyramid to trap oil, but has no anchor and uses boats to locate the trap. It has ballast weights located along the bottom of the tarp and/or at the corners of the trap. The improved floating oil-spill containment device has a large floating boom and weighted skirt surrounding the oil and gas entrapment area. The device is triangular (or more than three sides) and has a flexible tarp cover with a raised gas vent area. Boats pull on the apex of the triangles to maintain tension and to allow the device to move to optimum locations to trap oil and gas. The gas is retrieved from a higher buoyant part of the tarp, and oil is retrieved from the floating oil layer contained in the device. These devices can be operated in relatively severe weather, since waves will break over the devices without causing oil leaking. Also, natural

Use of Oil-Based Mud Cutting Waste in Cement Clinker Manufacturing

OpenAIRE

Saif Al-Dhamri, H; Black, L

2014-01-01

Oil-based Mud (OBM) cutting waste is generated during the process of oil well drilling. The drilled rocks are removed from deep within the drilled well and pumped to the surface. The portion removed , known at "cutting", is a mixture of rocks, mud, water and oil. Most drilling companies store this waste in open yards with no specific treatment solution. The environmental regulations in Oman specify that storage should involve isolation, to prevent penetration of the contamination to the surfa...

Calcined solids storage facility closure study

International Nuclear Information System (INIS)

Dahlmeir, M.M.; Tuott, L.C.; Spaulding, B.C.

1998-02-01

The disposal of radioactive wastes now stored at the Idaho National Engineering and Environmental Laboratory is currently mandated under a open-quotes Settlement Agreementclose quotes (or open-quotes Batt Agreementclose quotes) between the Department of Energy and the State of Idaho. Under this agreement, all high-level waste must be treated as necessary to meet the disposal criteria and disposed of or made road ready to ship from the INEEL by 2035. In order to comply with this agreement, all calcined waste produced in the New Waste Calcining Facility and stored in the Calcined Solids Facility must be treated and disposed of by 2035. Several treatment options for the calcined waste have been studied in support of the High-Level Waste Environmental Impact Statement. Two treatment methods studied, referred to as the TRU Waste Separations Options, involve the separation of the high-level waste (calcine) into TRU waste and low-level waste (Class A or Class C). Following treatment, the TRU waste would be sent to the Waste Isolation Pilot Plant (WIPP) for final storage. It has been proposed that the low-level waste be disposed of in the Tank Farm Facility and/or the Calcined Solids Storage Facility following Resource Conservation and Recovery Act closure. In order to use the seven Bin Sets making up the Calcined Solids Storage Facility as a low-level waste landfill, the facility must first be closed to Resource Conservation and Recovery Act (RCRA) standards. This study identifies and discusses two basic methods available to close the Calcined Solids Storage Facility under the RCRA - Risk-Based Clean Closure and Closure to Landfill Standards. In addition to the closure methods, the regulatory requirements and issues associated with turning the Calcined Solids Storage Facility into an NRC low-level waste landfill or filling the bin voids with clean grout are discussed

Calcined solids storage facility closure study

Energy Technology Data Exchange (ETDEWEB)

Dahlmeir, M.M.; Tuott, L.C.; Spaulding, B.C. [and others

1998-02-01

The disposal of radioactive wastes now stored at the Idaho National Engineering and Environmental Laboratory is currently mandated under a {open_quotes}Settlement Agreement{close_quotes} (or {open_quotes}Batt Agreement{close_quotes}) between the Department of Energy and the State of Idaho. Under this agreement, all high-level waste must be treated as necessary to meet the disposal criteria and disposed of or made road ready to ship from the INEEL by 2035. In order to comply with this agreement, all calcined waste produced in the New Waste Calcining Facility and stored in the Calcined Solids Facility must be treated and disposed of by 2035. Several treatment options for the calcined waste have been studied in support of the High-Level Waste Environmental Impact Statement. Two treatment methods studied, referred to as the TRU Waste Separations Options, involve the separation of the high-level waste (calcine) into TRU waste and low-level waste (Class A or Class C). Following treatment, the TRU waste would be sent to the Waste Isolation Pilot Plant (WIPP) for final storage. It has been proposed that the low-level waste be disposed of in the Tank Farm Facility and/or the Calcined Solids Storage Facility following Resource Conservation and Recovery Act closure. In order to use the seven Bin Sets making up the Calcined Solids Storage Facility as a low-level waste landfill, the facility must first be closed to Resource Conservation and Recovery Act (RCRA) standards. This study identifies and discusses two basic methods available to close the Calcined Solids Storage Facility under the RCRA - Risk-Based Clean Closure and Closure to Landfill Standards. In addition to the closure methods, the regulatory requirements and issues associated with turning the Calcined Solids Storage Facility into an NRC low-level waste landfill or filling the bin voids with clean grout are discussed.

Classified facilities for environmental protection

International Nuclear Information System (INIS)

Anon.

1993-02-01

The legislation of the classified facilities governs most of the dangerous or polluting industries or fixed activities. It rests on the law of 9 July 1976 concerning facilities classified for environmental protection and its application decree of 21 September 1977. This legislation, the general texts of which appear in this volume 1, aims to prevent all the risks and the harmful effects coming from an installation (air, water or soil pollutions, wastes, even aesthetic breaches). The polluting or dangerous activities are defined in a list called nomenclature which subjects the facilities to a declaration or an authorization procedure. The authorization is delivered by the prefect at the end of an open and contradictory procedure after a public survey. In addition, the facilities can be subjected to technical regulations fixed by the Environment Minister (volume 2) or by the prefect for facilities subjected to declaration (volume 3). (A.B.)

Comparing ignitability for in situ burning of oil spills for an asphaltenic, a waxy and a light crude oil as a function of weathering conditions under arctic conditions

DEFF Research Database (Denmark)

Fritt-Rasmussen, Janne; Brandvik, Per Johan; Villumsen, Arne

2012-01-01

(asphalthenic), Kobbe (light oil) and Norne (waxy), for ignitability as a function of ice conditions and weathering degree. The crude oils (9 L) were weathered in a laboratory basin (4.8 m3) under simulated arctic conditions (0, 50 and 90% ice cover). The laboratory burning tests show that the ignitability...... is dependent on oil composition, ice conditions and weathering degree. In open water, oil spills rapidly become “not ignitable” due to the weathering e.g. high water content and low content of residual volatile components. The slower weathering of oil spills in ice (50 and 90% ice cover) results in longer time......-windows for the oil to be ignitable. The composition of the oils is important for the window of opportunity. The asphalthenic Grane crude oil had a limited timewindow for in situ burning (9 h or less), while the light Kobbe crude oil and the waxy Norne crude oil had the longest time-windows for in situ burning (from...

Low Speed Wind Tunnel Facility (LSWTF)

Data.gov (United States)

Federal Laboratory Consortium — Description: This facility consists of a large-scale, low-speed open-loop induction wind tunnel which has been modified to house a linear turbine cascade. A 125-hp...

Relaxation of cntrol of oil industries in Europe

Energy Technology Data Exchange (ETDEWEB)

Sugimura, Nobuaki [The Inst. of Energy Economics, Tokyo, (Japan)

1989-03-01

This article summarizes the results of a survey including field surveys on the actual states and trends of relaxation of the control of oil industries in EC states. In classifying EC states by the degree of the government influence over the industries of oil refining and distribution, there are the group consisting of UK, West Germany and France, etc. where no control is imposed on individual oil companies in the fields of quantity and price of oil, the group consisting of Italy, etc. where no control exists on quantity, but price is partially controlled, and the group consisting of Spain and Greece, etc. where the government controls both quantity and price at the present stage although they are pushing relaxation of such control in accordance with the terms and conditions at the time of their entry to EC. The oil policy of EC is to remove as far as possible interferences of the governments and open its oil market free. This and the trend of over supply of oil since 1980 are two major factors of relaxation of oil industries control in Europe. The author considers it desirable that the oil industries in Japan should withstand international competitions by their inventiveness, creativity and effort, and importation of oil products should be held at a supplementary degree in view of their characters. 2 refs., 1 fig., 4 tabs.

Flood offers new hope for marginal oil fields

Energy Technology Data Exchange (ETDEWEB)

1966-03-14

The economics of producing a marginal Cardium sand oil field in west-central Alberta have been greatly improved by introduction of an inexpensive waterflood pressure maintenance and secondary recovery project. Canadian Gridoil Ltd. is now in full operation at its Willesden Green Cardium Unit No. 5. Of the 8.1 million bbl estimated original oil in place, only 9% would have been recoverable by primary depletion. The waterflood is calculated to add 13%, for ultimate recovery of 22% or 1.8 million bbl. This waterflood installation is considered a prototype of economical and profitable pressure maintenance systems which can be built to advantage in marginal oil fields in Alberta. Ultimate returns in the form of increased oil production and more than doubled oil recovery will be immensely greater than the capital investment of $195,000 in the facilities. Assuming GOR control and full well allowables, the entire capital cost should be paid out within 3 years. Life of the field is estimated at not less than 25 years.

NEB view of development potential and markets for heavy crude oil. [Canada

Energy Technology Data Exchange (ETDEWEB)

Scotland, W A; Gutek, A M.H.

1977-01-01

The phased reduction in total crude oil and equivalent exports, from 911 Mpbd in 1974 to 465 Mbpd in 1976, has no doubt had a disruptive effect on the rate of development of heavy crude oil reserves. The effect could have become more series as total exports continued to drop. However, the separate licensing of heavy crude oil for export will allow heavy crude oil to enter available markets until the early 1980s. The construction of one or several upgrading facilities by the early 1980s, combined with growing domestic requirements for heavy crude oil feedstock, could make the disposition of heavy oil largely independent of the purchasing patterns of export markets. The prospect of increased market stability combined with increasing cash flows should provide an appropriate environment to optimize the role that heavy oil resources can play in Canada's future energy balance. (12 refs.)

Gobe oil - small and bankable

International Nuclear Information System (INIS)

Boey Kit Yin.

1997-01-01

Government blessing was bestowed on the Gobe oil development and production project in Papua New Guinea (PNG) at the end of December 1996 following the issuance of two petroleum development licences and a Gobe pipeline licence. Construction began shortly after that, in the early months of 1997, making it close to a year since a US98.5m project financing facility was completed for the project. (author)

Human Health and Ecological Risk Assessment for the Operation of the Explosives Waste Treatment Facility at Site 300 of the Lawrence Livermore National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Gallegos, G; Daniels, J; Wegrecki, A

2007-10-01

This document contains the human health and ecological risk assessment for the Resource Recovery and Conservation Act (RCRA) permit renewal for the Explosives Waste Treatment Facility (EWTF). Volume 1 is the text of the risk assessment, and Volume 2 (provided on a compact disc) is the supporting modeling data. The EWTF is operated by the Lawrence Livermore National Laboratory (LLNL) at Site 300, which is located in the foothills between the cities of Livermore and Tracy, approximately 17 miles east of Livermore and 8 miles southwest of Tracy. Figure 1 is a map of the San Francisco Bay Area, showing the location of Site 300 and other points of reference. One of the principal activities of Site 300 is to test what are known as 'high explosives' for nuclear weapons. These are the highly energetic materials that provide the force to drive fissionable material to criticality. LLNL scientists develop and test the explosives and the integrated non-nuclear components in support of the United States nuclear stockpile stewardship program as well as in support of conventional weapons and the aircraft, mining, oil exploration, and construction industries. Many Site 300 facilities are used in support of high explosives research. Some facilities are used in the chemical formulation of explosives; others are locations where explosive charges are mechanically pressed; others are locations where the materials are inspected radiographically for such defects as cracks and voids. Finally, some facilities are locations where the machined charges are assembled before they are sent to the onsite test firing facilities, and additional facilities are locations where materials are stored. Wastes generated from high-explosives research are treated by open burning (OB) and open detonation (OD). OB and OD treatments are necessary because they are the safest methods for treating explosives wastes generated at these facilities, and they eliminate the requirement for further handling

Oil's role in free trade agreement crux of Mexico's petroleum sector dilemma

International Nuclear Information System (INIS)

Anon.

1992-01-01

Mexico's president Salinas' efforts at privatization have not yet touched Mexico's most valuable industry, oil. That remains under control of state owned Petroleos Mexicanos. Pemex and Mexico's huge oil union have come under increasing criticism for alleged abuses of power. In addition, controversy rages as to the true extent of Mexican oil resources and whether Pemex has the wherewithal to meet domestic demand and sustain oil exports. Critics also contend opening Mexico's oil sector to foreign participation would introduce new efficiencies and cost cutting measures in the cash strapped state oil industry. This paper reports that at the center of the controversy is the proposed Free Trade Agreement among Mexico, the U.S., and Canada, pushed strongly by Salinas. Oil's role in the FTA may prove the pact's main sticking point

SRTC criticality technical review: Nuclear Criticality Safety Evaluation 93-18 Uranium Solidification Facility's Waste Handling Facility

International Nuclear Information System (INIS)

Rathbun, R.

1993-01-01

Separate review of NMP-NCS-930058, open-quotes Nuclear Criticality Safety Evaluation 93-18 Uranium Solidification Facility's Waste Handling Facility (U), August 17, 1993,close quotes was requested of SRTC Applied Physics Group. The NCSE is a criticality assessment to determine waste container uranium limits in the Uranium Solidification Facility's Waste Handling Facility. The NCSE under review concludes that the NDA room remains in a critically safe configuration for all normal and single credible abnormal conditions. The ability to make this conclusion is highly dependent on array limitation and inclusion of physical barriers between 2x2x1 arrays of boxes containing materials contaminated with uranium. After a thorough review of the NCSE and independent calculations, this reviewer agrees with that conclusion

Oil and gas products and energy equipment

International Nuclear Information System (INIS)

1996-01-01

The planned activities of the Canadian oil and gas products and energy equipment industry for 1996-1997, were presented. The sector is made up of approximately 1500 small and medium sized enterprises. The Canadian oil field manufacturing and servicing industry holds only a small 2.5% share of the world export market, but it is recognized internationally as one of the leading suppliers of advanced petroleum equipment. Their exports include specialized equipment for extracting oil sands, gathering and treatment facilities for sour gas, underbalanced drilling technologies, equipment for wells experiencing declining production rates, top motor drives, winter drilling rigs, and horizontal drilling technologies. They also offer petroleum industry software products. Most exploration and production equipment sold abroad by Canadian firms is manufactured in Canada, but there is an increasing trend toward manufacturing in the country of operation. 2 tabs

Imported resources - gas/oil

Energy Technology Data Exchange (ETDEWEB)

Jakob, K. [MOL Hungarian Oil and Gas Company, Budapest (Hungary)

1995-12-01

The goal of this presentation is to provide information on issues of crude oil and natural gas supply at a conference addressing the problems of energy in Eastern and Central Europe. Although this can inevitably be performed through the {open_quotes}binoculars{close_quotes} of the petroleum sector of my country, I will try to present the issues and challenges that are thought to be characteristic in general for the region.

Value of NMR logging for heavy oil characterization

Energy Technology Data Exchange (ETDEWEB)

Chen, S.; Chen, J.; Georgi, D. [Baker Hughes, Calgary, AB (Canada); Sun, B. [Chevron Energy Technology Co., Calgary, AB (Canada)

2008-07-01

Non-conventional, heavy oil fields are becoming increasingly important to the security of energy supplies and are becoming economically profitable to produce. Heavy oil reservoirs are difficult to evaluate since they are typically shallow and the connate waters are very fresh. Other heavy oil reservoirs are oil-wet where the resistivities are not indicative of saturation. Nuclear magnetic resonance (NMR) detects molecular level interactions. As such, it responds distinctively to different hydrocarbon molecules, thereby opening a new avenue for constituent analysis. This feature makes NMR a more powerful technique than bulk oil density or viscosity measurements for characterizing oils, and is the basis for detecting gas in heavy oil fields. NMR logging, which measures fluid in pore space directly, is capable of separating oil from water. It is possible to discern movable from bound water by analyzing NMR logs. The oil viscosity can be also quantified from NMR logs, NMR relaxation time and diffusivity estimates. The unique challenges for heavy oil reservoir characterization for the NMR technique were discussed with reference to the extra-fast decay of the NMR signal in response to extra-heavy oil/tars, and the lack of sensitivity in measuring very slow diffusion of heavy oil molecules. This paper presented various methods for analyzing heavy oil reservoirs in different viscosity ranges. Heavy oil fields in Venezuela, Kazakhstan, Canada, Alaska and the Middle East were analyzed using different data interpretation approaches based on the reservoir formation characteristics and the heavy oil type. NMR direct fluid typing was adequate for clean sands and carbonate reservoirs while integrated approaches were used to interpret extra heavy oils and tars. It was concluded that NMR logs can provide quantitative measures for heavy oil saturation, identify sweet spots or tar streaks, and quantify heavy oil viscosity within reasonable accuracy. 14 refs., 16 figs.

A self-cleaning underwater superoleophobic mesh for oil-water separation

KAUST Repository

Zhang, Lianbin

2013-07-31

Oil-water separation has recently become a global challenging task because of the frequent occurrence of oil spill accidents due to the offshore oil production and transportation, and there is an increasing demand for the development of effective and inexpensive approaches for the cleaning-up of the oily pollution in water system. In this study, a self-cleaning underwater superoleophobic mesh that can be used for oil-water separation is prepared by the layer-by-layer (LbL) assembly of sodium silicate and TiO2 nanoparticles on the stainless steel mesh. The integration of the self-cleaning property into the all-inorganic separation mesh by using TiO2 enables the convenient removal of the contaminants by ultraviolet (UV) illumination, and allows for the facile recovery of the separation ability of the contaminated mesh, making it promising for practial oil-water separation applications.

A remote oil spill detection system for early warning of spills at waterfront or land-based facilities

International Nuclear Information System (INIS)

Parsons, M.J.; Stocky, W.D.; Westerlind, J.; Gram, H.R.; Jadamec, M.P.; Johnson, J.R.

1992-01-01

Early detection of spills during loading/unloading of crude oil or products at terminals or plants is essential for quickly stopping the spill and minimizing its impact. Such detection is particularly difficult at night or in remote areas. In order to provide a reliable and inexpensive spill detection system for such an application, a joint development process was undertaken to redesign an oil spill detection buoy system which had been successfully tested in the 1970s. The sensor's operation is based on the stimulated fluorescence of oil and selective wavelength detection of this fluorescence. The prototype system consists of a flotation buoy for remote deployment of the sensor, rechargeable battery supply, a land-based computer base station, and radio signal transmitter. The oil spill detection buoy was modified in 1991 and tested in the laboratory. Field trials are under way and tests to date have confirmed the unit's ability to detect oil and to differentiate between various types of oil and/or products, particularly if the software is alerted to the type of product being transferred. 2 figs

Evaluation of Indian milkweed (Calotropis gigantea) seed oil as alternative feedstock for biodiesel

Science.gov (United States)

Calotropis gigantea (Indian milkweed) is a common plant in Asia that grows as a weed on open waste ground. Flowering and fruiting take place throughout the year. In this study, Indian milkweed oil was evaluated as a potential feedstock for biodiesel production. The oil was extracted from Indian milk...

Waste oil management at the Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Oakes, T.W.; Bird, J.C.; Shank, K.E.; Kelley, B.A.; Harrison, L.L.; Clark, B.R.; Rogers, W.F.

1980-01-01

It is the policy of the Oak Ridge National Laboratory (ORNL) to require that oily substances be handled and disposed of in a manner that protects the environment and personnel from harm. Federal regulations prohibit the discharge of oil into navigable waters, with stiff penalties possible to violators. A strict waste oil management program has been developed and implemented because of the potential for oil problems resulting from the large and varied uses of oil at the Laboratory. Also, past records of improper discharges of oil have mandated immediate corrective actions. In order to resolve the problems of waste oil at the Laboratory, the ORNL Waste Oil Investigation Committee was formed on March 14, 1979. The work of the committee included a survey of every building and area of the Laboratory to locate the presence of oil and the pathways of oil discharges to the environment. The committee also provided a basis for the development of oil spill procedures and waste oil disposal. The Department of Environmental Management (DEM) of the Industrial Safety and Applied Health Physics Division at ORNL has the responsibility of developing environmental protection procedures for the handling and disposal of oil. It approves storage and collection facilities, disposal methods, and disposal sites for oil-containing wastes. The DEM has developed and implemented an ORNL Environmental Protection Procedure for oils and an oil spill prevention and countermeasure plan. In order to familiarize ORNL personnel with the problems and procedures of waste oil, the DEM has held seminars on the subject. This report reviews the findings of the Waste Oil Investigation Committee and the actions of the laboratory management and the DEM in dealing with the waste oil problem at ORNL

The case for a large heavy oil stream

International Nuclear Information System (INIS)

Reimer, P.

2005-01-01

EnCana Corporation markets significant proprietary and third party crude oil production in North America. This presentation presented details of EnCana's projected resources as well as estimated proved reserves in Canadian oil sands. Details of the Western Canadian heavy oil market were presented. Issues concerning Western Canadian Select (WCS) were also presented, including details of distillation and asphalt characteristics. Details of the WCS synthetic bitumen synergy were examined, as well as quality management issues. It was suggested that further optimization of WCS facilities include reduced operating complexity; less tank proliferation; delivery quality consistency; and reliability. WCS refiner advantages were also evaluated. Shipping and ramping details were discussed, along with growth potential. It was noted that WCS satisfies all the criteria for a benchmark crude. It was concluded that the case for a large Canadian heavy oil stream includes reduced operating complexity; optimized logistics; delivery quality consistency; improved stream liquidity; and enhanced price discovery. tabs., figs

Engineering and construction projects for oil and gas processing facilities: Contracting, uncertainty and the economics of information

International Nuclear Information System (INIS)

Berends, Kees

2007-01-01

The amount of oil and gas processing capacity required to meet demand during the next 20 years is more than twice the amount realised during the last decades. Engineering and Construction contractors (ECs) play a key role in the development and implementation of Large Engineering and Construction Projects (LECPs) for these facilities. We examine the characteristics of LECPs, demand and supply of the contracting market and the strategies traditionally adopted by owners to contract out the development and implementation of these projects to ECs. We demonstrate that these traditional strategies are not longer effective, in the current 'sellers market', to mitigate the oligopolistic economic inefficiencies. As the 'overheating' of the contracting market is expected to continue for a considerable period of time, alternative contracting strategies are required. Contract theory, particularly the economics of information on LECPs, indicates how alternative contracting strategies can be used to overcome economic inefficiencies. The effective use of these alternative strategies requires increased owner involvement and their effectiveness is contingent upon owner competency and ECs acting as the owner's agent rather than its adversary. This will require an organisational and behavioural change process for both owners and ECs

Effects of selected thermophilic microorganisms on crude oils at elevated temperatures and pressures. Final report

Energy Technology Data Exchange (ETDEWEB)

Premuzic, E.T.; Lin, M.S.

1995-07-01

During the past several years, a considerable amount of work has been carried out showing that microbially enhanced oil recovery (MEOR) is promising and the resulting biotechnology may be deliverable. At the Brookhaven National Laboratory (BNL), systematic studies have been conducted which dealt with the effects of thermophilic and thermoadapted bacteria on the chemical and physical properties of selected types of crude oils at elevated temperatures and pressures. Particular attention was paid to heavy crude oils from Venezuela, California, Alabama, Arkansas, Wyoming, Alaska, and other oil producing areas. Current studies indicate that during the biotreatment several chemical and physical properties of crude oils are affected. The oils are (1) emulsified; (2) acidified; (3) there is a qualitative and quantitative change in light and heavy fractions of the crudes; (4) there are chemical changes in fractions containing sulfur compounds; (5) there is an apparent reduction in the concentration of trace metals; (6) the qualitative and quantitative changes appear to be microbial species dependent; and (7) there is a distinction between {open_quotes}biodegraded{close_quotes} and {open_quotes}biotreated{close_quotes} oils. Preliminary results indicate the introduced microorganisms may become the dominant species in the bioconversion of oils. These studies also indicate the biochemical interactions between crude oils and microorganisms follow distinct trends, characterized by a group of chemical markers. Core-flooding experiments have shown significant additional crude oil recoveries are achievable with thermophilic microorganisms at elevated temperatures similar to those found in oil reservoirs. In addition, the biochemical treatment of crude oils has technological applications in downstream processing of crude oils such as in upgrading of low grade oils and the production of hydrocarbon based detergents.

Vectors of Defects in Reinforced Concrete Structures in Onshore Oil and Gas Process Plants

Directory of Open Access Journals (Sweden)

Dabo Baba Hammad

2018-01-01

Full Text Available There is a global outcry over the speedy deterioration of structures in oil and gas facilities. While marine environment is considered the leading factor in the deterioration of offshore structures, there is no single factor considered as the main cause of the problem in onshore structures. Therefore, the aim of this paper is to present the result of global survey on the major factors causing the deterioration of concrete structures in onshore oil and gas facilities. To realize the objectives of the paper, an e-questionnaire was administered through two International LinkedIn groups with a membership mainly dominated by experts in onshore oil and gas facilities. 159 respondents completed the questionnaires, and the reliability of the responses was calculated to be 0.950 which is considered excellent. Relative importance index was used in ranking the factors, and it was observed that environmental factors ranked as the dominant factors causing the deterioration of concrete structures in onshore process plants. Another important finding in the study is the role that experience plays on the perception of experts on the causes of defects on concrete structures.

Effect of olive storage conditions on Chemlali olive oil quality and the effective role of fatty acids alkyl esters in checking olive oils authenticity.

Science.gov (United States)

Jabeur, Hazem; Zribi, Akram; Abdelhedi, Ridha; Bouaziz, Mohamed

2015-02-15

The present paper accounts for the study of the storage of Chemlali olive fruits at two conditions of limited aerobiosis: in closed plastic bags and in open perforated plastic boxes for different periods before oil extraction. The ultimate objective is to investigate the effect of the container type of the postharvest fruit storage on the deterioration of the olive oil quality. The results have shown that the oil quality of Chemlali olives deteriorated more rapidly during fruit storage in closed plastic bags than in perforated plastic boxes. Therefore, the use of perforated plastic boxes is recommended for keeping the olives for longer periods of storage. The repeated measures analysis of variance of all parameters analyzed indicated that the olive oil quality is mainly affected by the olives storage conditions (containers type and storage periods). Finally, blends of extra-virgin olive oil and mildly deodorized low-quality olive oils can be detected by their alkyl esters concentrations. Copyright © 2014 Elsevier Ltd. All rights reserved.

Corrosion problems and solutions in oil refining and petrochemical industry

CERN Document Server

Groysman, Alec

2017-01-01

This book addresses corrosion problems and their solutions at facilities in the oil refining and petrochemical industry, including cooling water and boiler feed water units. Further, it describes and analyzes corrosion control actions, corrosion monitoring, and corrosion management. Corrosion problems are a perennial issue in the oil refining and petrochemical industry, as they lead to a deterioration of the functional properties of metallic equipment and harm the environment – both of which need to be protected for the sake of current and future generations. Accordingly, this book examines and analyzes typical and atypical corrosion failure cases and their prevention at refineries and petrochemical facilities, including problems with: pipelines, tanks, furnaces, distillation columns, absorbers, heat exchangers, and pumps. In addition, it describes naphthenic acid corrosion, stress corrosion cracking, hydrogen damages, sulfidic corrosion, microbiologically induced corrosion, erosion-corrosion, and corrosion...

ICALEPS 2005 : opening session

CERN Multimedia

Maximilien Brice

2005-01-01

ICALEPCS 2005, the tenth International Conference on Accelerator and Large Experimental Physics Control Systems, will be held in Geneva, Switzerland, 10-14 Oct. 2005 at the International Conference Center Geneva (CICG). ICALEPCS 2005 thus falls in the year that UNESCO has declared the "World Year of Physics". ICALEPCS covers all aspects of control and operation of Experimental Physics facilities such as particle accelerators, particle detectors, optical telescopes, radio telescopes, nuclear fusion facilities like Tokamaks, nuclear reactors, lasers, etc .... Opening session by . A. Daneels (CERN): Introducting ICALEPCS 2005 . C.Lamprecht (Republic & State of Geneva): Welcome speech . J. Lister (EPFL): Welcome speech . J. Engelen (CERN): The machine and experiment challenges of LHC

Transesterification of jojoba oil, sunflower oil, neem oil, rocket seed oil and linseed oil by tin catalysts

International Nuclear Information System (INIS)

Shah, Mazloom; Tariq, Muhammad; Ali, Saqib; Guo, Qing-Xiang; Fu, Yao

2014-01-01

The methanolysis of jojoba oil has been studied in the presence of tin powder, dibutyltin diacetate (C 4 H 9 ) 2 Sn(OOCCH 3 ) 2 , dioctyltin diacetate (C 8 H 17 ) 2 Sn(OOCCH 3 ) 2 , dibutyltin oxide (C 4 H 9 ) 2 SnO, dioctyltin oxide (C 8 H 17 ) 2 SnO, diphenyltin oxide (C 6 H 5 ) 2 SnO, dibutyltin chloride dihydroxide (C 4 H 9 ) 2 Sn(OH) 2 Cl, butyltinhydroxide hydrate (C 4 H 9 )Sn(=O)OH.xH 2 O, Ni nanoparticles and Pd nanoparticles act as catalysts. Among these, 1 weight % of dibutyltin diacetate shows the maximum conversion. Then, methanolysis of sunflower oil, neem oil, rocket seed oil and linseed oil into methyl esters studied in the presence of 1% dibutyltin diacetate as a catalyst and was compared their percentage conversions. The experimental yield for the conversion of jojoba oil, sunflower oil, neem oil, rocket seed oil and linseed oil into biodiesel was found to be 71%, 51%, 50.78%, 40.90% and 39.66%, respectively. The experimental yield of the conversion of jojoba oil into methyl esters was found to be increased up to 96% by increasing reaction time, without emulsion formation. The synthesis of jojoba seed oil biodiesel (JSOB), soybean oil biodiesel (SOB), neem oil biodiesel (NOB), rocket seed oil biodiesel (RSOB) and linseed oil biodiesel (LSOB) was confirmed by NMR ( 1 H and 13 C) and FT-IR analyses of biodiesel. - Highlights: • Transesterification of jojoba oil into biodiesel by tin and nano catalysts. • 1 weight % dibutyltin diacetate showed highest yield at 60 °C. • Catalytic conversion comparison of five oils using dibutyltin diacetate • The experimental yield of the conversion of jojoba oil increased with time. • FT-IR and NMR ( 1 H and 13 C) characterization

Perestroika, Soviet oil, and joint ventures

International Nuclear Information System (INIS)

Churkin, M. Jr.

1991-01-01

Glaznost, the freedom of expression in both the public and private sectors of the Soviet Union, has rapidly transformed the country form a largely isolated and closed society to one that is rapidly becoming more cosmopolitan and open to the West. Now that the Soviet Union is moving toward a free-market economy, a number of new laws are being generated to create a favorable environment for Western investment, especially joint ventures. First, crude oil sales have provided over 75% of much-needed hard currency, and oil has been the principal barter for manufactured goods produced in eastern Europe. Second, joint oil ventures with Western companies can reverse declining production levels and provide sufficient stimulus to turn around the economic recession. The Soviet Union has a very large inventory of discovered but undeveloped oil and gas fields. Most of these fields are difficult for the Soviets to produce technically, financially, and environmentally safely, and they are actively seeking appropriate Western partners. From an exploration point of view, the Soviet Union has probably the largest number of undrilled and highly prospective oil basins, which may replenish declining reserves in the West. Finally, the Soviet Union represents in the long term a large unsaturated market eager to absorb the surplus of goods and services in the Western world. Again, joint oil ventures could provide the convertible currency to increase East-West trade

Effects of open- and self-pollination treatments on genetic estimations in maize diallel experiment

Energy Technology Data Exchange (ETDEWEB)

Kahriman, F.; Egesel, C.O.; Zorlu, E.

2015-07-01

This study investigated the effects of open- and self-pollination treatments on genetic estimations and kernel biochemical content in a maize diallel experiment. A 7×7 complete reciprocal diallel set (7 parents and 42 hybrids) was used as plant material. Measured traits were: kernel weight per plant, protein content, oil content and carbohydrate content. General combining ability (GCA), specific combining ability (SCA), maternal effects (MAT), non-maternal effects (NMAT) and heterosis values were compared in open- and self-pollination treatments for measured traits. Results showed that the pollination treatments had a significant effect on all investigated traits. Parental lines and hybrid combinations gave different responses. Parents had relatively higher protein and oil content in self-pollination but hybrids had lower values in self-pollination compared with open-pollination. A considerable number of genotypes showed significant differences for genetic estimations (GCA, SCA, MAT, NMAT) and heterosis between open- and self-pollination treatments. Overall, findings suggest that evaluation of kernel quality traits should be made on selfed ear samples; however, evaluation for yield should be carried out on open-pollinated samples. (Author)

Climate-wise choices in a world of oil abundance

Science.gov (United States)

Brandt, Adam R.; Masnadi, Mohammad S.; Englander, Jacob G.; Koomey, Jonathan; Gordon, Deborah

2018-04-01

Constrained oil supply has given way to abundance at a time when strong action on climate change is wavering. Recent innovation has pushed US oil production to all-time heights and driven oil prices lower. At the same time, attention to climate policy is wavering due to geopolitical upheaval. Nevertheless, climate-wise choices in the oil sector remain a priority, given oil’s large role in modern economies. Here we use a set of open-source models along with a detailed dataset comprising 75 global crude oils (~25% of global production) to estimate the effects of carbon intensity and oil demand on decadal scale oil-sector emissions. We find that oil resources are abundant relative to all projections of 21st century demand, due to large light-tight oil (LTO) and heavy oil/bitumen (HOB) resources. We then investigate the ‘barrel forward’ emissions from producing, refining, and consuming all products from a barrel of crude. These oil resources have diverse life-cycle-greenhouse gas (LC-GHG) emissions impacts, and median per-barrel emissions for unconventional resources vary significantly. Median HOB life cycle emissions are 1.5 times those of median LTO emissions, exceeding them by 200 kgCO2eq./bbl. We show that reducing oil LC-GHGs is a mitigation opportunity worth 10–50 gigatonnes CO2 eq. cumulatively by 2050. We discuss means to reduce oil sector LC-GHGs. Results point to the need for policymakers to address both oil supply and oil demand when considering options to reduce LC-GHGs.

Distillation Time as Tool for Improved Antimalarial Activity and Differential Oil Composition of Cumin Seed Oil.

Science.gov (United States)

Zheljazkov, Valtcho D; Gawde, Archana; Cantrell, Charles L; Astatkie, Tess; Schlegel, Vicki

2015-01-01

A steam distillation extraction kinetics experiment was conducted to estimate essential oil yield, composition, antimalarial, and antioxidant capacity of cumin (Cuminum cyminum L.) seed (fruits). Furthermore, regression models were developed to predict essential oil yield and composition for a given duration of the steam distillation time (DT). Ten DT durations were tested in this study: 5, 7.5, 15, 30, 60, 120, 240, 360, 480, and 600 min. Oil yields increased with an increase in the DT. Maximum oil yield (content, 2.3 g/100 seed), was achieved at 480 min; longer DT did not increase oil yields. The concentrations of the major oil constituents α-pinene (0.14-0.5% concentration range), β-pinene (3.7-10.3% range), γ-cymene (5-7.3% range), γ-terpinene (1.8-7.2% range), cumin aldehyde (50-66% range), α-terpinen-7-al (3.8-16% range), and β-terpinen-7-al (12-20% range) varied as a function of the DT. The concentrations of α-pinene, β-pinene, γ-cymene, γ-terpinene in the oil increased with the increase of the duration of the DT; α-pinene was highest in the oil obtained at 600 min DT, β-pinene and γ-terpinene reached maximum concentrations in the oil at 360 min DT; γ-cymene reached a maximum in the oil at 60 min DT, cumin aldehyde was high in the oils obtained at 5-60 min DT, and low in the oils obtained at 240-600 min DT, α-terpinen-7-al reached maximum in the oils obtained at 480 or 600 min DT, whereas β-terpinen-7-al reached a maximum concentration in the oil at 60 min DT. The yield of individual oil constituents (calculated from the oil yields and the concentration of a given compound at a particular DT) increased and reached a maximum at 480 or 600 min DT. The antimalarial activity of the cumin seed oil obtained during the 0-5 and at 5-7.5 min DT timeframes was twice higher than the antimalarial activity of the oils obtained at the other DT. This study opens the possibility for distinct marketing and utilization for these improved oils. The antioxidant

pyOpenMS: a Python-based interface to the OpenMS mass-spectrometry algorithm library.

Science.gov (United States)

Röst, Hannes L; Schmitt, Uwe; Aebersold, Ruedi; Malmström, Lars

2014-01-01

pyOpenMS is an open-source, Python-based interface to the C++ OpenMS library, providing facile access to a feature-rich, open-source algorithm library for MS-based proteomics analysis. It contains Python bindings that allow raw access to the data structures and algorithms implemented in OpenMS, specifically those for file access (mzXML, mzML, TraML, mzIdentML among others), basic signal processing (smoothing, filtering, de-isotoping, and peak-picking) and complex data analysis (including label-free, SILAC, iTRAQ, and SWATH analysis tools). pyOpenMS thus allows fast prototyping and efficient workflow development in a fully interactive manner (using the interactive Python interpreter) and is also ideally suited for researchers not proficient in C++. In addition, our code to wrap a complex C++ library is completely open-source, allowing other projects to create similar bindings with ease. The pyOpenMS framework is freely available at https://pypi.python.org/pypi/pyopenms while the autowrap tool to create Cython code automatically is available at https://pypi.python.org/pypi/autowrap (both released under the 3-clause BSD licence). © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hydration of vegetable oils for high-grade Diesel fuel components; Hydrierung von Pflanzenoelen zu hochwertigen Dieselkraftstoffkomponenten

Energy Technology Data Exchange (ETDEWEB)

Endisch, M.; Olschar, M.; Kuchling, T. [TU Bergakademie Freiberg (Germany); Balfanz, U. [BP AG, Global Fuels Technology, Bochum (Germany)

2008-07-01

The legally regulated admixture of biogenic fuel components for diesel fuels are actually realized in Germany by an admixture of vegetable oil methylester (e.g. from rapeseed oil). The paper describes the hydration of vegetable oils as alternative to this procedure. Infrared and {sup 13}NMR spectroscopy were used to analyse the reaction kinetics for rapeseed, soy been and palm oil hydration. Experimental results of investigations under operational conditions using a continuous test facility and different vegetable oils identified the possibilities of this technology. The technology allows the high-yield production of diesel fuel components with certain numbers higher than average.

Studies of water-in-oil emulsions : testing of emulsion formation in OHMSETT

International Nuclear Information System (INIS)

Fingas, M.; Fieldhouse, B.

2001-01-01

A study was conducted to determine the stability of water-in-oil emulsions in the OHMSETT tank facility. The results were then compared with previous laboratory studies which suggested that the stability of emulsions can be grouped into four categories, stable, unstable, meso-stable and entrained. It has been determined that entrained emulsions can retain oil by viscous forces long enough for interfacial agents, resins and asphaltenes to stabilize the droplets. This paper also described the difference in viscosity between the 4 categories of emulsion stability. The OHMSETT tests were conducted in two series of one week each. The first series of tests were conducted in July and involved 12 experiments on 2 different types of oils which were placed at varying thicknesses on the water. The second set of tests were conducted in November and involved 12 experiments on 6 oils. The rheological properties of the oils were measured and compared to the same oils undergoing emulsification in the laboratory. The oils and water-in-oil states produced were found to have analogous properties between the laboratory and the first set of tests at the OHMSETT facility. All the oils tested produced entrained water-in-oil states in both the laboratory and the test tank. The energy in the two test conditions was found to be similar, with the OHMSETT emulsions similar to one produced in the laboratory at high energies. The second series of tests at OHMSETT did not result in the expected water in-oil- states. This unexpected result was most likely due to the residual surfactant from an earlier dispersant experiment. The study showed that the conditions for emulsion formation are analogous in the OHMSETT tank and in the laboratory tests. The level of energy is considered to be the major variant. It was concluded that the energy levels between the laboratory mixing experiments and the OHMSETT is similar. It was shown that surfactants left over from dispersant testing inhibited the formation

Results of the Weeks Island Strategic Petroleum Reserve Oil Leak Risk Assessment Study

International Nuclear Information System (INIS)

Molecke, M.A.; Hinkebein, T.E.; Bauer, S.J.; Linn, J.K.

1998-12-01

This study evaluated multiple, long-term environmental oil-contamination risk scenarios that could result from the potential leakage of UP to 1.5 million barrels of crude oil entombed in the Weeks Island SPR mine following site decommissioning and abandonment, and up to 100 years thereafter. This risk assessment also provides continuity with similar risk evaluations performed earlier and documented in the 1995 DOE Environmental Assessment for Decommissioning the Strategic Petroleum Reserve Weeks Island Facility (EA). This current study was requested by the DOE to help them determine if their previous Finding of No Significant Impact (FONSI), in the EA, is still valid or needs to be rescinded. Based on the calculated environmental risk results (in terms of clean-up and remediation expenses) presented in this risk assessment, including the calculated average likelihoods of oil release and potential oil-leakage volumes, none of the evaluated risk events would appear to satisfy the definition of significant environmental impact in National Environmental Policy Act (NEPA) terminology. The DOE may combine these current results with their earlier evaluations and interpretations in the 1995 EA in order to assess whether the existing FONSI is still accurate, acceptable, and valid. However, from a risk evaluation standpoint, the assessment of impacts appears to be the same whether only 10,000 to 30,000 barrels of crude oil (as considered in the 1995 EA), or up to 1.5 million barrels of oil (as considered herein) are abandoned in the Weeks Island SPR facility

Diverse wettability of superoleophilicity and superoleophobicity for oil spill cleanup and recycling

Science.gov (United States)

Xu, Mengya; Wang, Gang; Zeng, Zhixiang; Chen, Junjun; Zhang, Xingyuan; Wang, Longsheng; Song, Weiguang; Xue, Qunji

2017-12-01

The frequent marine oil spill accidents in nowadays has aroused great attention all over the world. Lots of superwetting absorption materials with 2D or 3D structures are fabricated to efficiently remove oil spill, but the desorption of the absorbed oil is more difficult. Oil contaminants adhere on the surface will decline the performance and reusability of the absorption materials. Discarding or burning them will bring secondary pollution. Faced with these problems, we prepared an oil extractor integrated by a superhydrophobic-superoleophilic stainless steels wire mesh and a 3D porous cellulose sponge with superhydrophilicity-superoleophilicity in air and superoleophobicity in water. The oil extractor can in situ collect oil spill no matter on the water or under the water. More importantly, it is good at underwater oil desorption, which ensure the recovery and reuse of oil, and meanwhile avoid the materials being fouled by oils. More than 85.5% of crude oil could be successfully discharged only in 2 min when the oil-contaminated sponge was placed in water. The findings in this work not only put forward a new strategy for collection and reuse of various "oils", but also offer a facile method to achieve a combination of two kinds of materials with diverse wettability.

Anomalous dispersion of magnetic spiky particles for enhanced oil emulsions/water separation.

Science.gov (United States)

Chen, Hui-Jiuan; Hang, Tian; Yang, Chengduan; Liu, Guishi; Lin, Di-An; Wu, Jiangming; Pan, Shuolin; Yang, Bo-Ru; Tao, Jun; Xie, Xi

2018-01-25

In situ effective separation of oil pollutants including oil spills and oil emulsions from water is an emerging technology yet remains challenging. Hydrophobic micro- or nano-materials with ferromagnetism have been explored for oil removal, yet the separation efficiency of an oil emulsion was compromised due to the limited dispersion of hydrophobic materials in water. A surfactant coating on microparticles prevented particle aggregation, but reduced oil absorption and emulsion cleaning ability. Recently, polystyrene microbeads covered with nanospikes have been reported to display anomalous dispersion in phobic media without surfactants. Inspired by this phenomenon, here magnetic microparticles attached with nanospikes were fabricated for enhanced separation of oil emulsions from water. In this design, the particle surfaces were functionalized to be superhydrophobic/superoleophilic for oil absorption, while the surface of the nanospikes prevented particle aggregation in water without compromising surface hydrophobicity. The magnetic spiky particles effectively absorbed oil spills on the water surface, and readily dispersed in water and offered facile cleaning of the oil emulsion. In contrast, hydrophobic microparticles without nanospikes aggregated in water limiting the particle-oil contact, while surfactant coating severely reduced particle hydrophobicity and oil absorption ability. Our work provides a unique application scope for the anomalous dispersity of microparticles and their potential opportunities in effective oil-water separation.

Market analysis of shale oil co-products. Summary report

Energy Technology Data Exchange (ETDEWEB)

1980-12-01

This study examines the potential for separating, upgrading and marketing sodium mineral co-products together with shale oil production. The co-products investigated are soda ash and alumina which are derived from the minerals nahcolite and dawsonite. Five cases were selected to reflect the variance in mineral and shale oil content in the identified resource. In the five cases examined, oil content of the shale was varied from 20 to 30 gallons per ton. Two sizes of facilities were analyzed for each resource case to determine economies of scale between a 15,000 barrel per day demonstration unit and a 50,000 barrel per day full sized plant. Three separate pieces of analysis were conducted in this study: analysis of manufacturing costs for shale oil and co-products; projection of potential world markets for alumina, soda ash, and nahcolite; and determination of economic viability and market potential for shale co-products.

Oil spill research program, U. S. Minerals Management Service

International Nuclear Information System (INIS)

LaBelle, R. P.; Mullin, J. V.; White, A. C.

1997-01-01

The oil spill prevention and response research program of the U.S. Minerals Management Service was described including its goals and objectives, some recently funded projects, and future research directions. As it is now the trend in most research organizations, a large part of the program is carried out in cooperation with other major research centers to leverage funds and to maximize study results. For example, joint research with Environment Canada focuses on the physical and chemical properties of dispersants, remote sensing and mapping oil slicks and shoreline cleanup strategies. Similarly, cooperative projects are underway with the National Institute of Standards and Technology in assessing the capabilities of in-situ burning as an oil spill response tool. Research capabilities of OHMSETT - The National Oil Spill Response Test Facility were also reviewed. A series of tables listed titles of research projects completed during 1995-1996. 5 tabs.,

Effect of liquid waste discharges from steam generating facilities

Energy Technology Data Exchange (ETDEWEB)

McGuire, H.E. Jr.

1977-09-01

This report contains a summary of the effects of liquid waste discharges from steam electric generating facilities on the environment. Also included is a simplified model for use in approximately determining the effects of these discharges. Four basic fuels are used in steam electric power plants: three fossil fuels--coal, natural gas, and oil; and uranium--presently the basic fuel of nuclear power. Coal and uranium are expected to be the major fuels in future years. The following power plant effluents are considered: heat, chlorine, copper, total dissolved solids, suspended solids, pH, oil and grease, iron, zinc, chrome, phosphorus, and trace radionuclides.

Effect of liquid waste discharges from steam generating facilities

International Nuclear Information System (INIS)