Oil additive and its effect

Directory of Open Access Journals (Sweden)

Vojtěch Kumbár

2013-01-01

Full Text Available The aim of this paper are experimental approaches, selected for analysis of the engine oils and described above, are surely sufficient for the needs of presented research. The spectrometry was used for determination of presence of selected chemical elements and especially metals in oil. Particles monitoring was employed in order to describe the amount, type, and size of friction particles. The temperature dependence of dynamic viscosity was evaluated by use of rotary viscometer. In case of all three approaches it is advantageous to compare the measured values with the results received for unused engine oil of the same marking and viscosity index. If the degradation of oil is classified as low or medium, it is possible to increase its service life for several thousands of kilometers. Mathematical model (polynomial 6th degree it was used for fitting experimental values.

Biodiesel production from tall oil with synthesized Mn and Ni based additives: effects of the additives on fuel consumption and emissions

Energy Technology Data Exchange (ETDEWEB)

Ali Keskin; Metin Guru; Duran Altiparmak [Mersin University, Mersin (Turkey). Technical Education Faculty

2007-05-15

In this study, biodiesel fuel and fuel additives were produced from crude tall oil that is a by-product in the pulp manufacturing by craft or sulphate pulping process. Fatty acids and resinic acids were obtained from crude tall oil by distillation method. Tall oil methyl ester (biodiesel) was produced from fatty acids. Resinic acids were reacted with NiO and MnO{sub 2} stoichiometrically for production of metallic fuel additives. Each metallic fuel additive was added at the rate of 8 {mu}mol/l and 12 {mu}mol/l to make mixtures of 60% tall oil methyl ester/40% diesel fuel (TE60) for preparing test fuels. Metallic fuel additives improved properties of biodiesel fuels, such as pour point and viscosity values. Biodiesel fuels were tested in an unmodified direct injection diesel engine at full load condition. Specific fuel consumption of biodiesel fuels increased by 6.00%, however, in comparison with TE60, it showed trend of decreasing with adding of additives. Exhaust emission profile of biodiesel fuels improved. CO emissions and smoke opacity decreased up to 64.28% and 30.91% respectively. Low NOx emission was also observed in general for the biodiesel fuels. 28 refs., 4 figs., 3 tabs.

An additive to well injection water for increasing the oil yield

Energy Technology Data Exchange (ETDEWEB)

Absov, M.T.; Abutalybov, M.G.; Aslanov, S.M.; Movruzov, E.N.; Musaev, R.A.; Tairov, N.D.

1979-03-05

This invention relates to oil production using flooding. The goal of this invention is to increase the oil yield of a producing formation. This is achieved by using a saponin solution as an additive to the water injected into the formation (with related organic substances which are complex organic nitrogen-free compounds from the glycoside group; these substances yield solution that foam easily with an agitation). The use of saponin facilitates good solubility in fresh, sea and formation (alkaline and hard) waters, as well as the absence of sediment formation during dissolution, low solid adsorption, and a significant decrease in the surface water tension on the oil-water boundary. The aqueous saponin solution makes it possible to decrease the production cost of oil, as well as to decrease the development time of the fields and the volume of water injected into the formation and to significantly increase the oil yield.

Experimental Investigation of the Use of Waste Mineral Oils as a Fuel with Organic-Based Mn Additive

Directory of Open Access Journals (Sweden)

Bülent Özdalyan

2018-06-01

Full Text Available The heat values of waste mineral oils are equal to the heat value of the fuel oil. However, heat value alone is not sufficient for the use of waste minerals oils as fuel. However, the critical physical properties of fuels such as density and viscosity need to be adapted to the system in order to be used. In this study, the engine oils used in the first 10,000 km of the vehicles were used as waste mineral oil. An organic-based Mn additive was synthesized to improve the properties of the waste mineral oil. It was observed that mixing the Mn additive with the waste mineral oil at different doses (4, 8, 12, and 16 ppm improves the viscosity of the waste oil and the flash point. The resulting fuel was evaluated for emission using different loads in a 5 kW capacity generator to compare the fuel with standard diesel fuel and to determine the effect of Mn addition. In the experimental study, it was observed that the emission characteristics of the fuel obtained from waste mineral oil were worse than diesel fuel, but some improvement was observed with Mn addition. As a result, we found that the use of waste mineral oils in engines in fuel standards was not appropriate, but may be improved with additives.

Activation of CO2-reducing methanogens in oil reservoir after addition of nutrient.

Science.gov (United States)

Yang, Guang-Chao; Zhou, Lei; Mbadinga, Serge Maurice; You, Jing; Yang, Hua-Zhen; Liu, Jin-Feng; Yang, Shi-Zhong; Gu, Ji-Dong; Mu, Bo-Zhong

2016-12-01

Nutrient addition as part of microbial enhanced oil recovery (MEOR) operations have important implications for more energy recovery from oil reservoirs, but very little is known about the in situ response of microorganisms after intervention. An analysis of two genes as biomarkers, mcrA encoding the key enzyme in methanogenesis and fthfs encoding the key enzyme in acetogenesis, was conducted during nutrient addition in oil reservoir. Clone library data showed that dominant mcrA sequences changed from acetoclastic (Methanosaetaceae) to CO 2 -reducing methanogens (Methanomicrobiales and Methanobacteriales), and the authentic acetogens affiliated to Firmicutes decreased after the intervention. Principal coordinates analysis (PCoA) and Jackknife environment clusters revealed evidence on the shift of the microbial community structure among the samples. Quantitative analysis of methanogens via qPCR showed that Methanobacteriales and Methanomicrobiales increased after nutrient addition, while acetoclastic methanogens (Methanosaetaceae) changed slightly. Nutrient treatment activated native CO 2 -reducing methanogens in oil reservoir. The high frequency of Methanobacteriales and Methanomicrobiales (CO 2 -reducers) after nutrient addition in this petroleum system suggested that CO 2 -reducing methanogenesis was involved in methane production. The nutrient addition could promote the methane production. The results will likely improve strategies of utilizing microorganisms in subsurface environments. Copyright © 2016 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Additivity vs Synergism: Investigation of the Additive Interaction of Cinnamon Bark Oil and Meropenem in Combinatory Therapy.

Science.gov (United States)

Yang, Shun-Kai; Yusoff, Khatijah; Mai, Chun-Wai; Lim, Wei-Meng; Yap, Wai-Sum; Lim, Swee-Hua Erin; Lai, Kok-Song

2017-11-04

Combinatory therapies have been commonly applied in the clinical setting to tackle multi-drug resistant bacterial infections and these have frequently proven to be effective. Specifically, combinatory therapies resulting in synergistic interactions between antibiotics and adjuvant have been the main focus due to their effectiveness, sidelining the effects of additivity, which also lowers the minimal effective dosage of either antimicrobial agent. Thus, this study was undertaken to look at the effects of additivity between essential oils and antibiotic, via the use of cinnamon bark essential oil (CBO) and meropenem as a model for additivity. Comparisons between synergistic and additive interaction of CBO were performed in terms of the ability of CBO to disrupt bacterial membrane, via zeta potential measurement, outer membrane permeability assay and scanning electron microscopy. It has been found that the additivity interaction between CBO and meropenem showed similar membrane disruption ability when compared to those synergistic combinations which was previously reported. Hence, results based on our studies strongly suggest that additive interaction acts on a par with synergistic interaction. Therefore, further investigation in additive interaction between antibiotics and adjuvant should be performed for a more in depth understanding of the mechanism and the impacts of such interaction.

Additivity vs Synergism: Investigation of the Additive Interaction of Cinnamon Bark Oil and Meropenem in Combinatory Therapy

Directory of Open Access Journals (Sweden)

Shun-Kai Yang

2017-11-01

Full Text Available Combinatory therapies have been commonly applied in the clinical setting to tackle multi-drug resistant bacterial infections and these have frequently proven to be effective. Specifically, combinatory therapies resulting in synergistic interactions between antibiotics and adjuvant have been the main focus due to their effectiveness, sidelining the effects of additivity, which also lowers the minimal effective dosage of either antimicrobial agent. Thus, this study was undertaken to look at the effects of additivity between essential oils and antibiotic, via the use of cinnamon bark essential oil (CBO and meropenem as a model for additivity. Comparisons between synergistic and additive interaction of CBO were performed in terms of the ability of CBO to disrupt bacterial membrane, via zeta potential measurement, outer membrane permeability assay and scanning electron microscopy. It has been found that the additivity interaction between CBO and meropenem showed similar membrane disruption ability when compared to those synergistic combinations which was previously reported. Hence, results based on our studies strongly suggest that additive interaction acts on a par with synergistic interaction. Therefore, further investigation in additive interaction between antibiotics and adjuvant should be performed for a more in depth understanding of the mechanism and the impacts of such interaction.

Effects of emulsifier addition on the crystallization and melting behavior of palm olein and coconut oil.

Science.gov (United States)

Maruyama, Jessica Mayumi; Soares, Fabiana Andreia Schafer De Martini; D'Agostinho, Natalia Roque; Gonçalves, Maria Inês Almeida; Gioielli, Luiz Antonio; da Silva, Roberta Claro

2014-03-12

Two commercial emulsifiers (EM1 and EM2), containing predominantly monoacylglycerols (MAGs), were added in proportiond of 1.0 and 3.0% (w/w) to coconut oil and palm olein. EM1 consisted of approximately 90% MAGs, whereas EM2 consisted of approximately 50% MAGs. The crystallization behavior of these systems was evaluated by differential scanning calorimetry (DSC) and microscopy under polarized light. On the basis of DSC results, it was clear that the addition of EM2 accelerated the crystallization of coconut oil and delayed the crystallization of palm olein. In both oils EM2 addition led to the formation of smaller spherulites, and these effects improved the possibilities for using these fats as ingredients. In coconut oil the spherulites were maintained even at higher temperatures (20 °C). The addition of EM1 to coconut oil changed the crystallization pattern. In palm olein, the addition of 3.0% (w/w) of this emulsifier altered the pattern of crystallization of this fat.

Long-acting poly(DL:lactic acid-castor oil) 3:7-bupivacaine formulation: effect of hydrophobic additives.

Science.gov (United States)

Sokolsky-Papkov, Marina; Golovanevski, Ludmila; Domb, Abraham J; Weiniger, Carolyn F

2011-12-01

To reduce formulation viscosity of bupivacaine/poly(DL lactic acid co castor oil) 3:7 without increasing bupivacaine release rates. Poly(DL lactic acid) 3:7 was synthesized and bupivacaine formulation prepared by mixing with additives ricinoleic acid or castor oil. In vitro release measurements identified optimum formulation. Anesthetized ICR mice were injected around left sciatic nerve using nerve stimulator with 0.1 mL of formulation. Animals received 10% bupivacaine-polymer formulation with 10% castor oil (p(DLLA:CO)3:7-10% bupi-10% CO) or 15% bupivacaine-polymer with 10% castor oil (p(DLLA:CO)3:7-15% bupi-10% CO). Sensory and motor block were measured. Viscosity of 10% and 15% bupivacaine-p(DLLA:CO)3:7 formulations was reduced using hydrophobic additives; however, castor oil reduced bupivacaine release rates and eliminated burst effect. Less than 10% of the incorporated bupivacaine was released during 6 h, and less than 25% released in 24 h in vitro. In vivo formulation injection resulted in a 24 h motor block and a sensory block lasting at least 72 h. Incorporation of hydrophobic low-viscosity additive reduced viscosity in addition to burst release effects. Bupivacaine-polymer formulation with castor oil additive demonstrated prolonged sensory analgesia in vivo, with reduced duration of motor block.

Pysical Properties of Soil with Addition of Sewage Dried with Heated Edible Oil

OpenAIRE

大坪, 政美; 中司, 敬; 中園, 修三; 中園, 英司; 徳留, 斉将

2000-01-01

The present study investigates the water holding capacity, density, permeability, and swelling properties of the soil samples mixed with the sewage that was dried with heated edible oil. For comparison similar experiments were conducted for the soil samples mixed with sun-dried sewage and sewage compost. The water holding capacity was higher for the soil samples with oil-dried and sun-dried sewage addition than for those with sewage-compost addition. For statically compacted soil samples, wit...

Stable dispersion of nanodiamonds in oil and their tribological properties as lubricant additives

Science.gov (United States)

Lee, Gyoung-Ja; Park, Jin-Ju; Lee, Min-Ku; Rhee, Chang Kyu

2017-09-01

Nanodiamonds (NDs) are innovative additives when a combination of mechanical, thermal, tribological, and dielectric properties are required. In this study, a surface modification with oleic acid (OA) is developed for the deaggregation and prolonged dispersion of NDs in oil, and the effect of the NDs as lubricant additives on the tribological properties of a steel substrate is investigated. The OA renders the ND surface hydrophobic and decreases the average particle size from 268.6 to 20.1 nm. The OA-treated NDs exhibit very stable dispersion in oil even after more than 10 days, compared with the untreated NDs. From the analyses of the friction coefficient, wear loss, and worn surfaces using a ball-on-disk wear test, it is concluded that a 0.05 wt% addition of OA-treated NDs in oil lubricant provides excellent friction and anti-wear properties with the friction coefficient being reduced by 23%.

EFFECT OF THYME ESSENTIAL OIL ADDITION ON PHYSICAL AND MICROBIOLOGICAL QUALITY OF TABLE EGGS

Directory of Open Access Journals (Sweden)

Henrieta Arpášová

2013-02-01

Full Text Available Essentialoils areintensivefragrant, oilyliquidsubstances containedindifferent parts of theplant. Their function is based on organoleptic effect and stimulation of organism to the production of digestive juices. Result is ahigherdigestibilityandabsorption of nutirents. Besides antibacterial properties, essential oils or their components have been shown to exhibit antiviral,antimycotic, antitoxigenic, antiparasitic, and insecticidal properties. In this experiment the effects of supplementation of the diet for laying hens with thyme essential oils on physical and microbiological egg parameters were studied.Hens of laying hybrid Hy-Line Brown (n=30 were randomly divided into 3 groups (n=10 and fed for 23 weeks on diets with thyme essential oil supplemented. In the first experimental group the feed mixture was supplemented with thyme essential oil addition in a dose 0.5 g/kg, in the second one some essential oil in a dose 1g/kg. The results suggest that all of qualitative parameters of egg internal content (yolk weight (g, yolk index, percentage portion egg yolk (%, yolk index, yolk colour (°HLR, albumen weight (g, percentage portion of albumen (%, Haugh Units (HU, albumen index were with thyme essential oil addition insignificantly influenced (P>0.05. The number of coliforms, enterococci, fungi and yeasts decreased with increasing dose of oil. The number of lactobacilli was zero in all groups.

Innocuous oil as an additive for reductive reactions involving zero valence iron

International Nuclear Information System (INIS)

Cary, J.W.; Cantrell, K.J.

1994-11-01

Reductive reactions involving zero valence iron appear to hold promise for in situ remediation of sites containing chlorinated hydrocarbon solvents and certain reducible metals and radionuclides. Treatment involves the injection of metallic iron and the creation of low levels of dissolved oxygen in the aqueous phase through oxidation of the metallic iron. The use of a biodegradable immiscible and innocuous organic liquid such as vegetable oil as an additive offers several intriguing possibilities. The oil phase creates a large oil-water interface that is immobile with respect to flow in the aqueous phase. This phase will act as a trap for chlorinated hydrocarbons and could potentially increase the reaction efficiency of reductive dehalogenation of chlorinated hydrocarbons by the metallic iron. When iron particles are suspended in the oil before injection they are preferentially held in the oil phase and tend to accumulate at the oil-water interface. Thus oil injection can serve as a mechanism for creating a stable porous curtain of metallic iron in the vadose to maintain a low oxygen environment which will minimize the consumption of the iron by molecular oxygen

The production of paper soaps from coconut oil and Virgin Coconut Oil (VCO) with the addition of glycerine as plasticizer

Science.gov (United States)

Widyasanti, Asri; Miracle Lenyta Ginting, Anastasia; Asyifani, Elgina; Nurjanah, Sarifah

2018-03-01

Hand washing with soap is important because it is proven to clean hands from germs and bacteria. The paper soapswere made from coconut oil and virgin coconut oil (VCO) with the addition of glycerin as a plasticizer. The aims of this research were to determine both formulation of paper soap using coconut oil and VCO based with addition of glycerin, and to determine the quality of the paper soapswhich is a disposable hand soap. This research used laboratory experimental method using descriptive analysis. The treatments of this research were treatment A (paper soap without the addition of glycerin), treatment B (paper soap with the addition of glycerin 10% (w/w)), treatment C (paper soap with the addition of glycerin 15% (w/w)), treatment D (paper soap with the addition of glycerin of 20% (w/w)). Parameters tested were moisture content, stability of foam, pH value, insoluble material in ethanol, free alkali content, unsaponified fat, antibacterial activity test, and organoleptic test. The result of physicochemical characteristics for bothcoconut oil-paper soap and VCO-paper soap revealed that treatment C (the addition of glycerin 15% (w/w) was the best soap formulation. Coconut Oil papersoap 15% w/w glicerin had water content 13.72%, the content of insoluble material in ethanol 3.93%, the content of free alkali 0.21%, and the content of unsaponified fat 4.06%, pH value 10.78, stability of foam 97.77%, and antibacterial activity against S. aureus 11.66 mm. Meanwhile, VCO paper soap 15% w/w glicerin had the value of water content of 18.47%, the value stability of foam of 96.7%, the pH value of 10.03, the value of insoluble material in ethanol of 3.49%, the value of free alkali content 0.17%, the value of unsaponified fat 4.91%, and the value of inhibition diameter on the antibacterial activity test 15.28 mm. Based on Mandatory Indonesian National Standard of solid soap SNI 3532:2016 showed that both of paper soap had not been accorded with SNI 3532:2016, unless the

The effect of oil additives on exhaust emission of internal combustion engines

International Nuclear Information System (INIS)

Dimitrovski, M.B.; Kuzmanovski, K.A.

1999-01-01

An attempt was conducted to acquire data on connection between motor oil and motor oil additives and exhaust emission of internal combustion engine. The consulted literature did not contain enough data, so experiments were conducted. The results of the experiments are presented on diagrams that have been processed in the computer program EXCEL. Conclusions that were made out of that work show the need of expanding research on the subject. (Author)

GC-MS and FI-IR analysis of the bio-oil with addition of ethyl acetate during storage

Directory of Open Access Journals (Sweden)

Le eZhang

2014-01-01

Full Text Available Different mass fractions (0%, 3%, 6%, 9%, 12%, and 15% of ethyl acetate were added to bio-oil for improving its storage stability during storage at 40℃ for 35d. For different bio-oils during storage, physical properties were characterized and chemical components were determined by GC-MS and FT-IR. The results of properties characterization showed that, addition of ethyl acetate could instantly lower bio-oil viscosity, water content, and dramatically decrease the rate of aging. pH value of bio-oil can be instantly improved by adding ethyl acetate. GC-MS results revealed that addition of various content of ethyl acetate into bio-oil and its storage at 40℃ for 35d could both lead to disappearance of previous compounds and generation of new compounds. FT-IR results showed that addition of various content of ethyl acetate into bio-oils and its storage at 40℃ for 35d could slightly change the wavenumbers of substantial functional groups in bio-oils.

Anti-wear additive content in fully synthetic PAO and PAG base oils and its effect on electrostatic and tribological phenomena in a rotating shaft-oil-lip seal system

Science.gov (United States)

Gajewski, Juliusz B.; Głogowski, Marek J.

2013-03-01

The paper presents the results of experiments on electrostatic and tribological aspects of different anti-wear additive's contents when an additive is blended with different fully synthetic (poly-α-olefin) and PAG (polyalkylene glycol) base oils in a rotating shaft-oil and oil-lip seal interfacial system. The experimental results are the relationships of electric potential induced in a lip seal's stiffening ring to angular velocity of a rotating metal shaft and to temperature of the oils tested. The braking torque of a shaft is measured with a torquemeter sensor connected directly with a microprocessor-based system for controlling the rotational speed and for measuring the shaft's braking torque and oil temperature. The beneficial and promising results are obtained for PAG when an external DC electric field is applied to the system and the braking torque is then reduced for a certain combination of the base oil and additive's contents. On the basis of the former and present research results an analysis is made to permit one to show how the type of the oils and additives tested can affect both interfaces: rotating shaft-oil and oil-lip of the lip seal and especially the braking torque.

The effect of low molecular weight multifunctional additives on heavy oil viscosity

Energy Technology Data Exchange (ETDEWEB)

Oldenburg, T.B.P.; Yarranton, H.W.; Larter, S.R. [Calgary Univ., AB (Canada)

2010-07-01

Crude oils contain many small multifunctional low molecular weight components that act as linking molecules between larger functionalized species. The linkage molecules have a significant impact on the flow properties of hydrocarbon systems. This study investigated the use of a low molecular weight multiheteroatom species (LMWMH) as a molecular Velcro linking high molecular weight components together. LMWMH species were added to Albertan bitumens and heavy oil, and their impact on viscosity was investigated. Results of the experimental studies were then compared with the effects of hydrocarbon solvents on similar samples. The LMWMH species included bifunctional species and analogous alkyl and aryl monoamines that acted as blocking molecules to hinder the association of larger petroleum species. Density and viscosity measurements were conducted. A correlation method was used to predict the viscosity of the solvent-diluted heavy oil and bitumen samples. The study showed that of the tested additives, only aniline demonstrated an additional viscosity-reducing effect. The aniline inhibited asphaltene association and is a promising candidate for enhanced in-situ bitumen viscosity reduction. 23 refs., 4 tabs.

A Novel Terpolymer as Fluid Loss Additive for Oil Well Cement

Directory of Open Access Journals (Sweden)

Ming Li

2017-01-01

Full Text Available A terpolymer comprised of sodium styrene sulfonate (SSS, fumaric acid (FA, and acrylamide (AM was synthesized by aqueous free radical copolymerization and evaluated as fluid loss additive for oil well cement. The chemical structure and performance of the terpolymer were characterized by Fourier transform infrared (FTIR spectroscopy and thermal gravimetric analysis (TGA; the molecular weight and its distribution were determined by gel permeation chromatography (GPC. The optimum reaction conditions of polymerization were obtained: a reaction temperature of 50°C, a mass ratio of SSS/FA/AM 4 : 2 : 14, initiator 0.1%, and reaction time of 4 h; characterization indicated that the SSS/FA/AM had a certain molecular weight and excellent temperature-resistant and salt-resistant properties. The results show that SSS/FA/AM has a good fluid loss performance, in which the API fluid loss of the oil cement slurry could be controlled within 100 mL at 160°C. In addition, it had little effect on the cement compressive strength. The results of scanning electron microscopy (SEM of the filter cake showed that SSS/FA/AM could be adsorbed on the surface of the cement particles and produce a hydrated layer to prevent fluid loss from the oil well cement.

Micro-encapsulation of refined olive oil: influence of capsule wall components and the addition of antioxidant additives on the shelf life and chemical alteration.

Science.gov (United States)

Calvo, Patricia; Castaño, Angel Luís; Lozano, Mercedes; González-Gómez, David

2012-10-01

Although refined olive oils (ROOs) exhibit lower quality and less stability toward thermal stress than extra-virgin olive oils, these types of oil are gaining importance in the food industry. The inclusion of ROOs in processed food may alter the oxidative stability of the manufactured products, and therefore having technological alternatives to increase oil stability will be an important achievement. For this reason the main goal of this study was to assess the influence of the micro-encapsulation process on the ROO chemical composition and its oxidative stability. Factors such as microcapsule wall constituents and the addition of the antioxidant butyl hydroxytoluene were investigated in order to establish the most appropriate conditions to ensure no alteration of the refined olive oil chemical characteristics. The optimised methodology exhibited high encapsulation yield (>98%), with micro-encapsulation efficiency ranging from 35 to 69% according to the nature of the wall components. The encapsulation process slightly altered the chemical composition of the olive oil and protected the oxidative stability for at least 11 months when protein components were included as wall components. It was concluded that the presence of proteins constituents in the microcapsule wall material extended the shelf life of the micro-encapsulated olive oil regardless the use of antioxidant additives. Copyright © 2012 Society of Chemical Industry.

Rapid methodology via mass spectrometry to quantify addition of soybean oil in extra virgin olive oil: A comparison with traditional methods adopted by food industry to identify fraud.

Science.gov (United States)

da Silveira, Roberta; Vágula, Julianna Matias; de Lima Figueiredo, Ingrid; Claus, Thiago; Galuch, Marilia Bellanda; Santos Junior, Oscar Oliveira; Visentainer, Jesui Vergilio

2017-12-01

Fast and innovative methodology to monitors the addition of soybean oil in extra virgin olive oil was developed employing ESI-MS with ionization operating in positive mode. A certified extra virgin olive oil and refined soybean oil samples were analyzed by direct infusion, the identification of a natural lipid marker present only in soybean oil (m/z 886.68 [TAG+NH 4 ] + ) was possible. The certified extra virgin olive oil was purposely adulterated with soybean oil in different levels (1, 5, 10, 20, 50, 70, 90%) being possible to observe that the new methodology is able to detect even small fraud concentration, such as 1% (v/v). Additionally, commercial samples were analyzed and were observed the addition of soybean oil as a common fraud in this segment. This powerful analytical method proposed could be applied as routine analysis by control organization, as well as food industries, considering its pronounced advantages; simplicity, rapidity, elevated detectability and minor amounts of sample and solvent consumed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Synthesis and tribological studies of nanoparticle additives for pyrolysis bio-oil formulated as a diesel fuel

International Nuclear Information System (INIS)

Xu, Yufu; Peng, Yubin; Zheng, Xiaojing; Dearn, Karl D.; Xu, Hongming; Hu, Xianguo

2015-01-01

The tribological behaviour of pyrolysis bio-oil with a synthesized nano-Lanthanum oxide (La 2 O 3 ) additive was evaluated using a point contact four ball tribometer under different frictional conditions. Results were compared against a micro (μ)-La 2 O 3 additive and an un-additised bio-oil as a control. The results show that nano-La 2 O 3 impregnated bio-oil had better tribological properties than the control groups. Under the operating loads, the optimum nanoparticle concentration within the bio-oil was investigated. At these levels, the combined action of adsorbed bio-oil films on the worn surfaces and the bearing effects of the nano-La 2 O 3 minimized friction and wear. The tribo-mechanisms were ascribed to adhesive wear as a result of lubrication starvation under high loads, and abrasive wear at high rotational speeds as a result of combined deformation and aggregation of the nano-La 2 O 3 particles. - Highlights: • The tribological properties of pyrolysis bio-oil with (μ & n) La 2 O 3 were assessed. • Nano-La 2 O 3 was synthesized with diameters of approximately 20–1000 nm. • Bio-oil w. 1% nano-La 2 O 3 was the optimum additive & concentration for tribological properties. • 1% nano-La 2 O 3 reduced corrosive wear with stable lubrication film for test conditions. • Wear mechanisms were predominately adhesive for higher loads and abrasive for higher speeds

Fruit quality and olive leaf and stone addition affect Picual virgin olive oil triterpenic content.

Science.gov (United States)

Allouche, Yosra; Uceda, Marino; Jiménez, Antonio; Aguilera, M Paz; Gaforio, José Juan; Beltrán, Gabriel

2009-10-14

The present research aimed to evaluate whether Picual virgin olive oil triterpenic compounds are affected by the addition of variable quantities of stones and leaves before processing or by fruit resting on the ground during 3 months. Results showed that stone addition did not influence triterpenic dialcohol content (uvaol and erythrodiol), whereas triterpenic acids (oleanolic and maslinic) increased significantly when 20 and 30% stones were added. Leaves added at 2% increased significantly oleanolic acid, maslinic acid, and erythrodiol content by 83, 41, and 36%, respectively. During fruit resting on the ground, olive oils showed no differences in uvaol content, a slight increase in erythrodiol, and a gradual increase in both oleanolic and maslinic acids, obtaining at the end of the experiment contents nearly 10- and 3-fold higher than control oils. These results confirm that olive oil triterpenic composition is modified by the factors analyzed.

The Influence of Palm Oil Addition on Sunflower Halva Stability and Texture

Directory of Open Access Journals (Sweden)

Vlad Muresan

2014-05-01

Full Text Available Halva is one of the most popular food products of Middle Eastern and North African countries. Worldwide, the most known halva contains roasted sesame seeds, while usually in Eastern European countries the most appreciated is sunflower halva. However, even if sunflower halva is an appreciated product, it has currently a quality below the expectations of the new generation of consumers. Sunflower halva main issue is caused by the oil which separates at the surface during storage, determining a low commercial aspect of the product. Thus, the aim of this work was to assess the influence of palm oil addition on sunflower halva stability and texture. Five samples containing different oil percentages [w/w] (1%, 2%, 3%, 4%, 5% were prepared, as well as a control sample prepared using the standard recipe (no palm oil added. The texture of all samples was analyzed by an instrumental method, while the colloidal stability was determined by a gravimetric technique during 40 days of storage at two different temperatures (1-2ºC and 15-20ºC. After the storage test at 1-2oC, there were not significant differences between the samples, for all palm oil containing samples as well as for control the percentages of separated oil being below 0.6%. With respect to the control sample, the halva samples containing 1%, 4% and 5% of palm oil showed a decrease in their stability, while samples containing 2% and 3% showed an improved stability (3.44% and 1.78% of separated oil. During this study it was established that the sample containing 3% palm oil was the most favorable, regarding its textural properties, as well as its colloidal stability. 

Socializing the Addition of Jambal Siam (Pangasius hypophtalmus Fish Stomach Oil and Kerapu (Cromileptes sp Fish Oil in Baby Porridge for Satisfy Omega 3 and Omega 6 Standard

Directory of Open Access Journals (Sweden)

Mirna Ilza

2015-12-01

Full Text Available The research aim on the socialization of the addition of jambal siam (Pangasius hypophtalmus fish stomach oil and kerapu (Cromileptes sp fish oil in baby porridge for satisfy omega 3 and omega 6 standard was implemented around Pekanbaru and Bangkinang (Kampar district. The addition of fish oil is done based on the standard of the WHO weight which conform to the age of the baby. The baby’s weight is very less than WHO standard dose given 50 mg/day, less weight given 40 mg/ day, and normal weight is 30 mg/day. Weight gain weighed and also observed the development of psychomotor babies each week for 8 weeks. Based on initial weight babies at the age of 10–12 months without the addition of jambal siam (Pangasius hypophtalmus fish stomach oil and kerapu (Cromileptes sp fish oil in baby porridge, 70.7% had a normal body weight increase and 23.3% have added weight which is too late. After the addition of jambal siam (Pangasius hypophtalmus fish stomach oil and kerapu (Cromileptes sp fish oil in baby porridge obtained added weight and motor development towards a better i.e. were 93.4% had normal motor development of appropriate age and the remaining 6.6% still have weight and psychomotor development too late i.e. newborn weight was initially very less than the WHO standard.

Fatty acids profile and quality characteristics of broiler chicken meat fed different dietary oil sources with some additives

Directory of Open Access Journals (Sweden)

Engy Fayz Zaki

2018-04-01

Full Text Available The study was carried out to investigate the effect of feeding broiler chicken on different vegetable oils with feed additives on the quality characteristics of chicken meat. A total of 216 one-day-old chicks of (Hubbard strain were randomly assigned to six dietary treatments as (2×3 factorial designs where two sources of dietary oil with three levels of commercial multi-enzyme feed additives. Treatments were: soybean oil only (T1, soybean oil+ ZAD (T2, soybean oil+ AmPhi-BACT (T3, palm oil only (T4, palm oil + ZAD (T5 and palm oil + AmPhi- BACT (T6.  Results showed that feeding broiler chicken on different types of dietary oils had significant effect on the fatty acid profile of broiler chicken meat. UFA/SFA ration of broiler chicken groups (T4, T5adT6 were significantly lower compared with (T1, T2 and T3 groups. Broiler fed on soybean oil had significantly higher n-6: n-3 ration compared with broiler fed on palm oil. Regardless of the source of dietary oil, significant differences were observed in the most of fatty acid profile in the chicken meat among levels of commercial multi- enzyme feed additives. Meat of T5and T6 had the higher pH value, followed by meat of T1and T3 groups, while the lowest pH value found in meat of T2 and T4. The higher cooking loss was found in meat of T4 while, meat of T5had the lowest value. Data of chilling loss indicated that the differences between dietary treatments were not significantly different except for meat of T6 which had the higher chilling loss. No significant differences were found in color measurements between dietary treatments.

Tomatoes in oil recovery. [Plant waste additives improve yield

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

The waste from processing tomato, squash and pepper stalks found unexpected use in recovery of oil. Even a negligible amount thereof in an aqueous solution pumped into an oil-bearing formation turned out to be sufficient to increase the yield. Substances of plant origin, which improve dramatically the oil-flushing properties of water, not only increase the recovery of oil, but reduce the volume of fluid to be pumped into the stratum. The staff of the Institute of Deep Oil and Gas Deposits of the Azerbaijan Academy of Sciences, who proved the technological and economical advantages of using the waste from plant processing, transmitted their findings to the oil workers of Baku. The scientists have concluded that there is a good raw material base in this republic for utilizing this method on oil-bearing formations.

Development and growth of science-intensive production of lube oil additives in the transition to a market economy

International Nuclear Information System (INIS)

Zhurba, A.S.; Burlaka, G.G.; Pravikov, A.A.

1992-01-01

In the Soviet petroleum refining and petrochemical industry, preference with respect to science-intensive development should be given to lube oil additives as production objects which are characterized by high cost of scientific developments and which are major factors influencing scientific and technical progress in many branches of the economy. The role of additives is becoming much more significant because of dwindling resources of crude oils with high potential contents of lube fractions (18-20%); other factors are the phasing out of ecologically harmful technologies, unsatisfactory utilization of used oils, and so on. Under these conditions, the use of additives is essentially the only method for increasing the efficiency of lube oil production and improving the product quality, which, together with improved design and materials for the lubricating components and an improvement of the professional and cultural level of their operation, will logically bring forth a marked curtailment of lubricant consumption. Outside the USSR, additive production, thanks to its conversion into a rapidly progressing subbranch of the petroleum refining industry, has become the object of capital investment. Under conditions of a market economy, additive manufacture is characterized by a high level of specialization and concentration, various forms of cooperation, profitability, and competitiveness. Because of the existence of a branch network of retail and wholesale trade, production of lube oils and additives can be adjusted rapidly to meet the requirements of the domestic and world market

Socializing the Addition of Jambal Siam (Pangasius hypophtalmus Fish Stomach Oil and Kerapu (Cromileptes sp Fish Oil in Baby Porridge for Satisfy Omega 3 and Omega 6 Standard

Directory of Open Access Journals (Sweden)

Mirna Ilza

2015-12-01

Full Text Available The research aim on the socialization of the addition of jambal siam (Pangasius hypophtalmusfish stomach oil and kerapu (Cromileptes sp fish oil in baby porridge for satisfy omega 3 and omega6 standard was implemented around Pekanbaru and Bangkinang (Kampar district. The additionof fish oil is done based on the standard of the WHO weight which conform to the age of the baby.The baby’s weight is very less than WHO standard dose given 50 mg/day, less weight given 40 mg/day, and normal weight is 30 mg/day. Weight gain weighed and also observed the developmentof psychomotor babies each week for 8 weeks. Based on initial weight babies at the age of 10–12months without the addition of jambal siam (Pangasius hypophtalmus fish stomach oil and kerapu(Cromileptes sp fish oil in baby porridge, 70.7% had a normal body weight increase and 23.3%have added weight which is too late. After the addition of jambal siam (Pangasius hypophtalmusfish stomach oil and kerapu (Cromileptes sp fish oil in baby porridge obtained added weight andmotor development towards a better i.e. were 93.4% had normal motor development of appropriateage and the remaining 6.6% still have weight and psychomotor development too late i.e. newbornweight was initially very less than the WHO standard.Keywords: Fish oil, baby, body weight, physichomotor

Physico-chemical characteristics and sensory acceptance of Italiantype salami with canola oil addition

Directory of Open Access Journals (Sweden)

Nelcindo Nascimento Terra

2014-02-01

Full Text Available The aim of this study was to evaluate the effects of partial pork fat replacement with emulsified canola oil in Italian-type salami. Three treatments were done: Control (100% pork fat, without fat replacement, T1 (15% pork fat was replaced by emulsified canola oil and T2 (30% pork fat was replaced by emulsified oil canola. There were evaluated the salamis’ physicochemical characteristics (pH, water activity, weight loss, color and lipid oxidation during the manufacture and storage period, and sensory evaluation after the manufacture process. The emulsified canola oil addition at different levels did not change the pH and color during the manufacture process, even though significant differences were found in these parameters during the storage period. The water activity did not differ significantly among the treatments. However, the treatments with emulsified canola oil added have a lower weight loss than the control. It was possible to observe an elevation on lipid oxidation values in the T2 during manufacture and storage periods, while in the T1, the values did not differ from the control at the end of manufactures and remained lower than the control during the storage period. Even more, the partial replacement of pork fat by emulsified canola oil did not affect the acceptance of the product for aroma, flavor, color, texture and visual appearance. Thus, the 15% pork fat replacement by emulsified canola oil in Italian-type salami is a viable alternative for the product diversification.

Time Course-Dependent Methanogenic Crude Oil Biodegradation: Dynamics of Fumarate Addition Metabolites, Biodegradative Genes, and Microbial Community Composition

Directory of Open Access Journals (Sweden)

Courtney R. A. Toth

2018-01-01

Full Text Available Biodegradation of crude oil in subsurface petroleum reservoirs has adversely impacted most of the world's oil, converting this resource to heavier forms that are of lower quality and more challenging to recover. Oil degradation in deep reservoir environments has been attributed to methanogenesis over geological time, yet our understanding of the processes and organisms mediating oil transformation in the absence of electron acceptors remains incomplete. Here, we sought to identify hydrocarbon activation mechanisms and reservoir-associated microorganisms that may have helped shape the formation of biodegraded oil by incubating oilfield produced water in the presence of light (°API = 32 or heavy crude oil (°API = 16. Over the course of 17 months, we conducted routine analytical (GC, GC-MS and molecular (PCR/qPCR of assA and bssA genes, 16S rRNA gene sequencing surveys to assess microbial community composition and activity changes over time. Over the incubation period, we detected the formation of transient hydrocarbon metabolites indicative of alkane and alkylbenzene addition to fumarate, corresponding with increases in methane production and fumarate addition gene abundance. Chemical and gene-based evidence of hydrocarbon biodegradation under methanogenic conditions was supported by the enrichment of hydrocarbon fermenters known to catalyze fumarate addition reactions (e.g., Desulfotomaculum, Smithella, along with syntrophic bacteria (Syntrophus, methanogenic archaea, and several candidate phyla (e.g., “Atribacteria”, “Cloacimonetes”. Our results reveal that fumarate addition is a possible mechanism for catalyzing the methanogenic biodegradation of susceptible saturates and aromatic hydrocarbons in crude oil, and we propose the roles of community members and candidate phyla in our cultures that may be involved in hydrocarbon transformation to methane in crude oil systems.

The addition of pineapple flesh and pineapple peels extracts to increase the quality of used cooking oil

Science.gov (United States)

Kusumawardani, R.; Hasanah, N.; Sukemi

2018-04-01

In Indonesia, reuse of cooking oil is high and common. Heating process and reuse of the cooking oil causes a change in its chemical constituents and decrease its qualities. This research aimed to investigate the addition of pineapple flesh extract (PFE) and pineapple peel extract (PPE) on the increment of the quality of oxidized (used) cooking oil. The cooking oil has been used three times. Treatment was done by mixing the used cooking oil with the extract (2:1) at 50°C. Peroxide value, FFA and iodine number of treated and untreated used cooking oils were measured by using titration method. The result showed that the treatment could increase the quality of the used cooking oils. PPE was better than PFE to increase the quality of the used cooking oil.

Oil base fluids without tensoactive additives; Fluidos a base de oleo sem tensoativos

Energy Technology Data Exchange (ETDEWEB)

Machado, Jose Carlos V; Aragao, Atila Fernando L [PETROBRAS, XX (Brazil). Centro de Desenvolvimento de Recursos Humanos Norte e Nordeste

1990-12-31

The goal of this paper is to define an ideal oil base fluid composition without tensoactive additives, since these may cause damage to producing formation during drilling or well completion. We investigated the rheological, filtrating and phase separation properties of the systems composed of diesel oil, organophilic clay and a polar agent (water or ethyl alcohol). In order to to that, we used the 286 Baroid digital rotating viscometer, filtrating cells standardized according to the American Petroleum Institute (AP) for temperatures of 25 deg C to 149 deg C and pressures of 6,89 x 10{sup 5} Pa (100 psig) to 3,44 x 10{sup 6} (500 psig), and the setting method, according to the determinations of respectively rheological, filtrating and phase separation parameters. Results proved that the composition: diesel oil-94% v/v, Na Cl saturated solution - 6% v/v and bentone - 17,1 to 22,8 kg/m{sup 3} (6 to 8 lb/bbl), is ideal to meet the properties required for drilling and well completion operations for low densities, that is 0,84% to 1,02 (6,9 to 8,5 ib/gal). In order to obtain densities in the interval of 1,02 to 1,14 (8,5 to 9,5 ib/gal) the system should be condensed with calcite (Ca CO{sub 3}) and the base fluid composition should be : diesel oil-94 to 98% v/v, Na Cl saturated solution - 2 to 6% v/v and bentone 17,1 to 22,8 kg/m{sup 3} (6 to 8 ib/bbl). The average cost per barrel for the systems studied here is of the same order of conventional oil base fluids (with tensoactive additives). (author) 13 refs., 7 figs., 3 tabs.

Oil base fluids without tensoactive additives; Fluidos a base de oleo sem tensoativos

Energy Technology Data Exchange (ETDEWEB)

Machado, Jose Carlos V.; Aragao, Atila Fernando L. [PETROBRAS, XX (Brazil). Centro de Desenvolvimento de Recursos Humanos Norte e Nordeste

1989-12-31

The goal of this paper is to define an ideal oil base fluid composition without tensoactive additives, since these may cause damage to producing formation during drilling or well completion. We investigated the rheological, filtrating and phase separation properties of the systems composed of diesel oil, organophilic clay and a polar agent (water or ethyl alcohol). In order to to that, we used the 286 Baroid digital rotating viscometer, filtrating cells standardized according to the American Petroleum Institute (AP) for temperatures of 25 deg C to 149 deg C and pressures of 6,89 x 10{sup 5} Pa (100 psig) to 3,44 x 10{sup 6} (500 psig), and the setting method, according to the determinations of respectively rheological, filtrating and phase separation parameters. Results proved that the composition: diesel oil-94% v/v, Na Cl saturated solution - 6% v/v and bentone - 17,1 to 22,8 kg/m{sup 3} (6 to 8 lb/bbl), is ideal to meet the properties required for drilling and well completion operations for low densities, that is 0,84% to 1,02 (6,9 to 8,5 ib/gal). In order to obtain densities in the interval of 1,02 to 1,14 (8,5 to 9,5 ib/gal) the system should be condensed with calcite (Ca CO{sub 3}) and the base fluid composition should be : diesel oil-94 to 98% v/v, Na Cl saturated solution - 2 to 6% v/v and bentone 17,1 to 22,8 kg/m{sup 3} (6 to 8 ib/bbl). The average cost per barrel for the systems studied here is of the same order of conventional oil base fluids (with tensoactive additives). (author) 13 refs., 7 figs., 3 tabs.

Corruption and reduced oil production: An additional resource curse factor?

International Nuclear Information System (INIS)

Al-Kasim, Farouk; Søreide, Tina; Williams, Aled

2013-01-01

Prominent contributions to the resource curse literature suggest weak governance and corruption are important factors behind the wide welfare variations observed among oil producing countries. How weak governance and corruption influence revenue management and expenditure decisions, as well as the possible welfare benefits derived from oil, are broadly discussed. How they impact upon volumes of oil produced has, however, attracted little attention. This paper combines a review of the resource curse and oil production literatures with findings from qualitative interviews with oil sector experts to appreciate the feasibility of connections between corruption and oil production below its potential. We make particular reference to environments where regulatory institutions or political accountability are weak and focus primarily on producer government and oil firm relations. Drawing on insights from geology, political science and economics, we suggest suboptimal production solutions can impact volumes of oil actually produced and create constraints on long term revenues for oil producing countries. We argue greater disclosure of information on oil production efficiency on a field-by-field and country-by-country basis will assist further investigation of the relationships between corruption and volumes of oil produced. - Highlights: ► We combine a literature review with qualitative interviews with oil experts. ► We focus on feasible connections between corruption and oil production levels. ► We suggest suboptimal production solutions can impact volumes of oil produced. ► Corruption may reinforce suboptimal oil production. ► More data on oil production efficiency by field and country will assist research

Additifs anticongelants pour huiles de moteurs Antifreezing Additives for Motor Oils

Directory of Open Access Journals (Sweden)

Denis J.

2006-11-01

Full Text Available Cet article présente d'abord les principales familles chimiques d'additifs de congélation. Les paraffines normales restant dans l'huile après le déparaffinage cristallisent à basse température sous forme de fines lamelles constituées de plusieurs couches de molécules accolées, qui se superposent en spirales. Ces lamelles s'enchevêtrent en bloquant l'écoulement de l'huile. Les additifs s'interposent, soit par adsorption, soit par cocristallisation en favorisant la croissance des lamelles en épaisseur, ce qui les rend moins aptes à l'enchevêtrement. This article begins by describing the main chemical families of pour-point depressant additives. The normal paraffins remaining in the oil after dewaxing crystallize at low temperature in the form of very thin platelets made up of several layers of associated molecules that are superposed in spirals. These platelets become entangled and prevent the flow of oil. Additives work either by adsorption or by cocrystallization, enhancing the growth of lamella thickness, thus making them less capable of becoming entangled.

The effect of magnesium-based additives on particulate emissions from oil-fired power plants

Energy Technology Data Exchange (ETDEWEB)

Martinez, L.S.; Galeano, V.C.; Pena, E.S.; Caballero, P.G.

1986-02-01

To improve present knowledge of characteristics of particulate emissions from large-size boilers, in particular the role played by magnesium-oxide slurries, research was carried out with the following main objectives in mind: To identify the elementary chemical composition of emissions from a large boiler burning heavy fuel-oil; To define the differences caused by the use of MgO slurries regarding both quantity and characteristics of emissions; To study the boiler's transient response to sudden changes in additive dosage. The use of different fuel-oil during the experiments has given cause to discuss the following aspects: The joint presence of carbon and sulfur in particulate matter; The influence of certain characteristics of fuel-oil in emissions.

The Effect Of Additional Detergent In Crude Palm Oil In The Process Of Separation Stearin

Science.gov (United States)

Rezekyah Hasibuan, Vina; aini, Nur; Febriyanti; Ayubi Pane, Salahudin Al

2018-03-01

This study aims to find out how much stearin is formed from the addition of detergent and to understand the process of separation of crude olein with crude stearin from raw material of crude palm oil (CPO). Using a detergent fractionation system, detergent fractionation is a continuous crystallization of oil with controlled cooling and the separation of fractions by weight or centrifuge after supplementing surfactant.

Quality determination of vegetable oils used as an addition to fermented meat products with different starter cultures

Directory of Open Access Journals (Sweden)

Hana Šulcerová

2017-01-01

Full Text Available There were developed samples of fermented meat products of „Mettwurst" with an addition of a starter culture pentosacceus AS-3/100 or probiotic culture Lactobacillus casei Lc-01 and its combinations for this thesis. A part of animal fat was replaced with vegetable oils - sunflower oil and rapeseed oil. For comparison, there was also used a sample without an addition of vegetable oil. There were determined the characteristics of fats in samples: saponification value, acidity value, esteric, iodine and peroxide value. The samples were determined on the day of production and always once a week in a period of three following weeks. Every single sample was hereby determined 3 times. According to the results, it is more advantageous to use the samples with sunflower oil with an addition of specific cultures Lactobacillus casei Lc-01 and Pediococcus pentosaceus AS-3/100. The saponification value when adding sunflower oil detects that the quality of fat remains stable till the 14th day of storage (p <0.05. The comparison of acid value detects that a sample with sunflower oil and culture Pediococcus pentosaceus AS-3/100 is more advantageous due to fast acidification in the first half of storage period. Good results of iodine and peroxide value had the variation of a sample with sunflower oil and a combination of both cultures. The variation of peroxide value maintained the lowest values. By using the samples with sunflower oil and unispecific cultures L. casei Lc-01 and P. pentosaceus AS-3/100, the culture P. pentosaceus AS-3/100, which remained stable till the 14th day of production, reached the best values of peroxide value. The sunflower oil is in spite of high content of PUFA more stable to which also contributes the increased content of vitamin E that works as an antioxidant here. The disadvantage of rapeseed oil is its higher susceptibility to oxidation. For reasons of faster decomposition of vegetable oils would be essential to cut down on the

Influence of polystyrene addition to cellulose on chemical structure and properties of bio-oil obtained during pyrolysis

International Nuclear Information System (INIS)

Rutkowski, Piotr; Kubacki, Andrzej

2006-01-01

The cellulose (C), polystyrene (PS) and cellulose/polystyrene (C-PS) mixtures (3:1, 1:1, 1:3 w/w) were subjected to a pyrolysis process to produce bio-oil. The pyrolytic oil yield was in the range of 45.5-94.8 wt% depending on the composition of the sample. Pyrolysis of polystyrene gives the highest oil yield, whereas for cellulose, the yield of liquid products was the lowest. The basic physicochemical properties of oils are strongly influenced by the original material and do not change additively. The polystyrene addition to cellulose clearly improves the quality of the bio-oil, resulting in decreases in acid number, pour point and density. The change of color is not so distinct. The FT-IR analysis of the oils showed that the oxygen functionalities and hydrocarbons contents highly depend on the composition of the cellulose/polystyrene mixture. The fractionation of bio-oils by column chromatography using hexane and benzene was followed by GC-MS analyses. Different classes of organic compounds were identified, i.e., carboxylic acids, phenols, aldehydes, ketones, esters, ethers and unsaturated linear and cyclic hydrocarbons. The proportion of hydrocarbons increases with a decrease of the cellulose/polystyrene ratio. The obtained results indicate that during pyrolysis, not only does decomposition of cellulose and polystyrene occur, but also, reactions between products from C and PS take place. That was proved by the presence of compounds identified only in the bio-oils obtained from C-PS compositions

Atmospheric pressure matrix-assisted laser desorption/ionization mass spectrometry of friction modifier additives analyzed directly from base oil solutions.

Science.gov (United States)

Widder, Lukas; Brennerb, Josef; Huttera, Herbert

2014-01-01

To develop new products and to apply measures of quality control quick and simple accessibility of additive composition in automo- tive lubrication is important. The aim of this study was to investigate the possibility of analyzing organic friction modifier additives by means of atmospheric pressure matrix-assisted laser desorption/ionization mass spectrometry [AP-MALDI-MS] from lubricant solu- tions without the use of additional separation techniques. Analyses of selected friction modifier ethoxylated tallow amines and oleic acid amide were compared using two ionization methods, positive-ion electrospray ionization (ESI) and AP-MALDI, using a LTQ Orbitrap mass spectrometer. Pure additives were characterized from solvent solutions, as well as from synthetic and mineral base oil mixtures. Detected ions of pure additive samples consisted mainly of [M + H]+, but also alkaLi metal adducts [M + Na]+ and [M + K]+ could be seen. Characterizations of blends of both friction modifiers from the base oil mixtures were carried out as well and showed significant inten- sities for several additive peaks. Thus, this work shows a method to directly analyze friction modifier additives used in the automotive industry from an oil blend via the use of AP-MALDI without any further separation steps. The method presented will further simplify the acquisition of data on lubricant composition and additives. Furthermore, it allows the perspective of analyzing additive reaction products directly from formulated oil blends.

Influences of Fuel Additive, Crude Palm and Waste Cooking Oil on Emission Characteristics of Small Diesel Engine

Science.gov (United States)

Khalid, Amir; Jaat, Norrizam; Manshoor, Bukhari; Zaman, Izzuddin; Sapit, Azwan; Razali, Azahari; Basharie, Mariam

2017-08-01

Major research has been conducted on the use of input products, such as rapeseed, canola, soybean, sunflower oil, waste cooking oil (WCO), crude palm oil (CPO) and crude jatropha oil as alternative fuels. Biodiesel is renewable, biodegradable and oxygenated, where it can be easily adopted by current existing conventional diesel engine without any major modification of the engine. To meet the future performance and emission regulations, is urged to improve the performance and exhaust emissions from biodiesel fuels. Hence, further investigation have been carried out on the emission characteristics of small diesel engine that fuelled by variant blending ratio of WCO and CPO with booster additive. For each of the biodiesel blends ratio from 5 to 15 percent volume which are WCO5, WCO10 and WCO15 for WCO biodiesel and CPO5, CPO10 and CPO15 for CPO biodiesel. The exhaust emissions were measured at engine speeds varied at 2000 rpm and 2500 rpm with different booster additive volume DRA (biodiesel without additive), DRB (0.2 ml) and DRC (0.4 ml). Emissions characteristics that had been measured were Hydrocarbon (HC), Carbon Monoxide (CO), Carbon Dioxide (CO2), Nitrogen Oxide (NOx), and smoke opacity. The results showed that increased of blending ratio with booster additive volume significantly decreased the CO emission, while increased in NOx and CO2 due to changes of fuel characteristics in biodiesel fuel blends.

Investigation of Technological Operations Affecting the Determination of Concentration of Ionol Additive in Insulating Oil in High-Voltage Equipment

Directory of Open Access Journals (Sweden)

Korobeynikov S.M.

2018-04-01

Full Text Available Ionol oxidation inhibitor level control is included into normative indicators list for diagnostics of internal insulation condition of any oil-filled high voltage device. Concentration of oxidation inhibitor in dielectric liquid should be from 0,08 % to 0,40 % mass. Power supply network chemistry laboratories use such methods as spectroscopy, spectrometry, chromatography and many others. Russian insulation service specialists use the method of ionol concentration measurement in oils based on gas-liquid chromatography. In the first place it is related to the fact that gas chromatographs are installed for several tasks, including definition of inhibitor’s mass concentration. However, as practice shows, the use of this method for additive analysis, especially in old acidified mineral oils is linked to some difficulties. The aim of this work is identify technologic faults that may occur during definition of ionol inhibitive additive in dielectric liquid with gas-liquid chromatography method, and, as a consequence, may lead to incorrect calculation of ionol additional concentration to oil, necessary for its antioxygenic properties maintenance and high insulation quality provision during high voltage device functioning. The object of the research is insulating oil with more than 35 years’ operating cycle, presenting a complex multiplex matrix of hydrocarbons and oxygenates preventing reliable determination of ionol additive with gas-liquid chromatography method. Executed researches show that the main input into “correct” final result obtention during calculation of additional additive concentration was made by such technological operations as water content in extractant and technology of sample introduction into chromatograph’s evaporation tank

Role of the thickening agent concentration and surfactant additions in the system's soap-oil

Energy Technology Data Exchange (ETDEWEB)

Shchegolev, G.G.; Trapeznikov, A.A.; Taranenko, V.G.

1973-03-01

The effect of the thickening agent concentration, surfactant additions and mechanical treatment on the microstructure and structural-mechanical properties of the system's lithium stearate-oil has been studied. The rate of cooling of the soap-oil system has been shown also to be of importance. The surfactants are less effective when introduced into a finished pseudogel, than when added during crystallization.

Evaluation of the efficiency of silicone polyether additives as foam inhibitor in crude oil

International Nuclear Information System (INIS)

Fraga, Assis K.; Santos, Raquel F.; Mansur, Claudia R.E.

2011-01-01

This work evaluates the chemical and physico-chemical properties of commercial anti-foam products based on silicone polyethers along with their efficiency in inhibiting foaming. The commercial surfactants were characterized by nuclear magnetic resonance (NMR) spectroscopy, size exclusion chromatography (SEC), determination of solubility in different solvents and measurement of the surface and interfacial tensions. A method to test the formation of foam in oil was used to mimic the operating conditions in gas-oil separators. The results show that the most polar additive was the most efficient in breaking up the foam. (author)

A potential study on clove oil, eugenol and eugenyl acetate as diesel fuel bio-additives and their performance on one cylinder engine

Directory of Open Access Journals (Sweden)

A. Kadarohman

2010-03-01

Full Text Available Research on the potency of essential oils as diesel fuel bio-additives has been reported. It also has been found out that clove oil has a better performance than turpentine oil on decreasing Break Specific Fuel Consumption (BSFC and reduces the exhaust emissions of the engine. Clove oil is essential oil the content of which is made of eugenol acting as the main component. Eugenol has a bulky structure, two oxygen atoms and can form eugenyl acetate from ester reaction. Eugenyl acetate has a bulkier structure and higher oxygen content than eugenol which leads to optimizing the process of fuel combustion. This experiment can give information about the potency of the bio-additive based on clove oil and eugenol and about the influence of oxygen enrichment with eugenol on the performance of the diesel fuel bio-additive. In general, this experiment covered three stages. The first step is the characterization of the diesel fuel bio-additive using a GCMS and FTIR spectrophotometer. The second step is the characterization of the diesel fuel bio-additive and composition optimization. The final step is conducting a diesel fuel bio-additive performance test on one cylinder engine on a laboratory scale. The results of the carried out experiment show that clove oil, eugenol and eugenyl acetate can decrease Break Specific Fuel Consumption (BSFC and reduce the exhaust emissions of the engine as well as oxygen enrichment can help in reaching optimal fuel combustion.

Enhancement of Engine Oil Wear and Friction Control Performance Through Titanium Additive Chemistry

International Nuclear Information System (INIS)

Guevremont, J.; Guinther, G.; Szemenyei, D.; Devlin, M.; Jao, T.; Jaye, C.; Woicik, J.; Fischer, D.

2008-01-01

Traditionally, wear protection and friction modification by engine oil is provided by zinc dithiophosphate (ZDDP) or other phosphorus compounds. These additives provide effective wear protection and friction control on engine parts through formation of a glassy polyphosphate antiwear film. However, the deposition of phosphorus species on automotive catalytic converters from lubricants has been known for some time to have a detrimental effect of poisoning the catalysts. To mitigate the situation, the industry has been making every effort to find ZDDP-replacement additives that are friendly to catalysts. Toward this goal we have investigated a titanium additive chemistry as a ZDDP replacement. Fully formulated engine oils incorporating this additive component have been found to be effective in reducing wear and controlling friction in a high-frequency reciprocating rig (HFRR), 4-ball bench wear, Sequence IIIG, and Sequence IVA engine tests. Surface analysis of the tested parts by Auger electron spectroscopy, secondary ion mass spectrometry (SIMS), and X-ray photoelectron spectroscopy (XPS) have shown that Ti species have been incorporated into the wear tracks and can only be found on the wear tracks. We used synchrotron based near edge X-ray absorption fine structure (NEXAFS) to investigate the chemical bonding mechanism of the Ti additive with the metal surface that affects the wear improvement mechanism. We postulate that Ti provides antiwear enhancement through inclusion in the metal/metal oxide structure of the ferrous surface by forming FeTiO3.

Combined effects of high pressure processing and addition of soy sauce and olive oil on safety and quality characteristics of chicken breast meat.

Science.gov (United States)

Kruk, Zbigniew A; Kim, Hyun Joo; Kim, Yun Ji; Rutley, David L; Jung, Samooel; Lee, Soo Kee; Jo, Cheorun

2014-02-01

This study was conducted to evaluate the combined effect of high pressure (HP) with the addition of soy sauce and/or olive oil on the quality and safety of chicken breast meats. Samples were cut into 100 g pieces and 10% (w/w) of soy sauce (SS), 10% (w/w) of olive oil (OO), and a mixture of both 5% of soy sauce and 5% olive oil (w/w) (SO) were pressurized into meat with high pressure at 300 or 600 MPa. Cooking loss was lower in OO samples than SS samples. With increased pressure to 600 MPa, the oleic acid content of OO samples increased. The total unsaturated fatty acids were the highest in SO and OO 600 MPa samples. Lipid oxidation was retarded by addition of olive oil combined with HP. The addition of olive oil and soy sauce followed by HP decreased the amount of volatile basic nitrogen during storage and reduced the population of pathogens. Sensory evaluation indicated that the addition of olive oil enhanced the overall acceptance and willingness to buy. In conclusion, the combination of HP with the addition of soy sauce and/or olive oil is an effective technology that can improve chemical, health, sensory qualities and safety of chicken breast.

Combined Effects of High Pressure Processing and Addition of Soy Sauce and Olive Oil on Safety and Quality Characteristics of Chicken Breast Meat

Directory of Open Access Journals (Sweden)

Zbigniew A. Kruk

2014-02-01

Full Text Available This study was conducted to evaluate the combined effect of high pressure (HP with the addition of soy sauce and/or olive oil on the quality and safety of chicken breast meats. Samples were cut into 100 g pieces and 10% (w/w of soy sauce (SS, 10% (w/w of olive oil (OO, and a mixture of both 5% of soy sauce and 5% olive oil (w/w (SO were pressurized into meat with high pressure at 300 or 600 MPa. Cooking loss was lower in OO samples than SS samples. With increased pressure to 600 MPa, the oleic acid content of OO samples increased. The total unsaturated fatty acids were the highest in SO and OO 600 MPa samples. Lipid oxidation was retarded by addition of olive oil combined with HP. The addition of olive oil and soy sauce followed by HP decreased the amount of volatile basic nitrogen during storage and reduced the population of pathogens. Sensory evaluation indicated that the addition of olive oil enhanced the overall acceptance and willingness to buy. In conclusion, the combination of HP with the addition of soy sauce and/or olive oil is an effective technology that can improve chemical, health, sensory qualities and safety of chicken breast.

The addition of medium-chain triglycerides to a purified fish oil-based diet alters inflammatory profiles in mice.

Science.gov (United States)

Carlson, Sarah J; Nandivada, Prathima; Chang, Melissa I; Mitchell, Paul D; O'Loughlin, Alison; Cowan, Eileen; Gura, Kathleen M; Nose, Vania; Bistrian, Bruce R; Puder, Mark

2015-02-01

Parenteral nutrition associated liver disease (PNALD) is a deadly complication of long term parenteral nutrition (PN) use in infants. Fish oil-based lipid emulsion has been shown in recent years to effectively treat PNALD. Alternative fat sources free of essential fatty acids have recently been investigated for health benefits related to decreased inflammatory response. We hypothesized that the addition of medium-chain triglycerides (MCT) to a purified fish oil-based diet would decrease the response to inflammatory challenge in mice, while allowing for sufficient growth and development. Six groups of ten adult male C57/Bl6 mice were pair-fed different dietary treatments for a period of twelve weeks, varying only in fat source (percent calories by weight): 10.84% soybean oil (SOY), 10% coconut oil (HCO), 10% medium-chain triglycerides (MCT), 3% purified fish oil (PFO), 3% purified fish oil with 3% medium-chain triglycerides (50:50 MCT:PFO) and 3% purified fish oil with 7.59% medium-chain triglycerides (70:30 MCT:PFO). An endotoxin challenge was administered to half of the animals in each group at the completion of dietary treatment. All groups demonstrated normal growth throughout the study period. Groups fed MCT and HCO diets demonstrated biochemical essential fatty acid deficiency and decreased IL-6 and TNF-α response to endotoxin challenge. Groups containing PFO had increased inflammatory response to endotoxin challenge, and the addition of MCT to PFO mitigated this inflammatory response. These results suggest that the addition of MCT to PFO formulations may decrease the host response to inflammatory challenge, which may pose potential for optimized PN formulations. Inclusion of MCT in lipid emulsions given with PN formulations may be of use in therapeutic interventions for disease states resulting from chronic inflammation. Copyright © 2015 Elsevier Inc. All rights reserved.

Study on the reutilization of clear fracturing flowback fluids in surfactant flooding with additives for Enhanced Oil Recovery (EOR).

Science.gov (United States)

Dai, Caili; Wang, Kai; Liu, Yifei; Fang, Jichao; Zhao, Mingwei

2014-01-01

An investigation was conducted to study the reutilization of clear fracturing flowback fluids composed of viscoelastic surfactants (VES) with additives in surfactant flooding, making the process more efficient and cost-effective. The clear fracturing flowback fluids were used as surfactant flooding system with the addition of α-olefin sulfonate (AOS) for enhanced oil recovery (EOR). The interfacial activity, emulsification activity and oil recovery capability of the recycling system were studied. The interfacial tension (IFT) between recycling system and oil can be reduced by 2 orders of magnitude to 10(-3) mN/m, which satisfies the basic demand of surfactant flooding. The oil can be emulsified and dispersed more easily due to the synergetic effect of VES and AOS. The oil-wet surface of quartz can be easily converted to water-wet through adsorption of surfactants (VES/AOS) on the surface. Thirteen core plug flooding tests were conducted to investigate the effects of AOS concentrations, slug sizes and slug types of the recycling system on the incremental oil recovery. The investigations prove that reclaiming clear fracturing flowback fluids after fracturing operation and reuse it in surfactant flooding might have less impact on environment and be more economical.

Modeling and Forecasting of Depletion of Additives in Car Engine Oils Using Attenuated Total Reflectance Fast Transform Infrared Spectroscopy

Directory of Open Access Journals (Sweden)

Ronald Nguele

2014-11-01

Full Text Available On average, additives make up to 7% of a typical lubricant base. Commonly, they are blended with lube oils to enhance specific features thereby improving their qualities. Ultimately, additives participate in the performance of car engine oils. Using an analytical tool, attenuated total reflectance fast transform infrared spectroscopy, various grades of car engine oils, at different mileages, were analyzed. Sulfate oxidation and wear were found to trigger chemical processes which, in the long run, cause lubricant degradation while carbonyl oxidation was observed to occur only at a slow rate. Based upon data obtained from infrared spectra and using a curve fitting technique, mathematical equations predicting the theoretical rates of chemical change due to the aforementioned processes were examined. Additive depletions were found to obey exponential regression rather than polynomial. Moreover, breakpoint (breakpoint is used here to denote the initiation of deterioration of additives and critical mileage (critical mileage defines the distance at which the lubricant is chemically unusable of both samples were determined.

Experimental researches about the influence of the additives for engine oils upon the work of the engine

International Nuclear Information System (INIS)

Dimitrovski, Mile; Mucevski, Kiril

2003-01-01

In this paper an attempt to get some cognitions about the influence of the additives for engine oils upon the working parameters of the internal combustion engines is made. During the experimental researches the changes of the basic parameters which determine the work of the engine, such as: the pressure of compression, the noise, the vibrations, the friction of the engine mechanism, the internal cleanliness of the engine and similar, were observed. It was conclude that the use of additives into the engine oil resulted with smoother work of the engine and cleaner exhausted as well. (Author)

Improved quality of frozen boer goat semen with the addition of sweet orange essential oil on tris yolk and gentamicin extender

Science.gov (United States)

Sitepu, S. A.; Zaituni, U.; Jaswandi; Hendri

2018-02-01

This research aimed to determine the extent of frozen semen quality Boer Goat by essential oils of sweet orange peel in tris yolk and gentamicin extender. Research has been conducted at the Laboratory Loka Penelitian Kambing Potong Sei Putih, Deli Serdang, North Sumatra in February 2017. This study used a completely randomized design with 4 treatments and 5 replications. Treatments are 0.25; 0.5; 0.75 and 1% essential oils as additional diluent. The parameters were measured percentage Motility, membrane integrity, acrosome integrity and viability Boer Goat frozen semen. The results showed that the addition of essential oils as diluent semen was significant (P essential oil as much as 1%.

Effect of lubricant oil additive on size distribution, morphology, and nanostructure of diesel particulate matter

International Nuclear Information System (INIS)

Wang, Yuesen; Liang, Xingyu; Shu, Gequn; Wang, Xiangxiang; Sun, Xiuxiu; Liu, Changwen

2014-01-01

Highlights: • Pour point depressant (PPD) has great impact on particulate matters. • The number of nanoparticles increases sharply after PPD is added. • Ambiguous boundaries can be found when the PPD additive was added. • PPD changes the size distribution into bimodal logarithmic. • Three nanostructure parameters are changed greatly by PPD. - Abstract: Effects of lubricant oil additive on the characterization of particles from a four-cylinder turbocharged diesel engine were investigated. Neat diesel and blended fuel containing oil pour point depressant (PPD) additive were chosen as the test fuels. Effects of different fuels on size distribution, morphology, and nanostructure of the diesel particles were studied. Transmission electron microscopy (TEM) and high resolution TEM (HRTEM) were employed to study the morphology and nanostructure parameters. Particle size distribution was measured by fast particulate spectrometer (DMS 500). According to the experimental results, distribution of the primary particles size of the two fuels conforms to Gaussian distribution, whereas the mean diameter of blended fuel is larger than that of neat diesel at 1200 rpm, which is contrarily smaller at 2400 rpm. Besides, fractal dimension (D f ) of aggregates increases close to 2 (D f = 1.991), indicating that the structure became compacter with adding PPD. As to the nanostructure parameters of the blended fuel particles, the layer fringe length decreases from 1.191 nm to 1.064 nm, while both the separation distance and tortuosity increase. The changes in the nanostructure parameters indicate that the particles are more ordered and compressed with burning pure diesel. Results of blended fuel from DMS show that more particles, particularly nucleation mode particles, were discharged. In addition, its size distribution become bimodal logarithmic at 2400 rpm. All these results can provide new information of the effects of oil PPD additive on the formation and characterization of

EDTA addition enhances bacterial respiration activities and hydrocarbon degradation in bioaugmented and non-bioaugmented oil-contaminated desert soils.

Science.gov (United States)

Al Kharusi, Samiha; Abed, Raeid M M; Dobretsov, Sergey

2016-03-01

The low number and activity of hydrocarbon-degrading bacteria and the low solubility and availability of hydrocarbons hamper bioremediation of oil-contaminated soils in arid deserts, thus bioremediation treatments that circumvent these limitations are required. We tested the effect of Ethylenediaminetetraacetic acid (EDTA) addition, at different concentrations (i.e. 0.1, 1 and 10 mM), on bacterial respiration and biodegradation of Arabian light oil in bioaugmented (i.e. with the addition of exogenous alkane-degrading consortium) and non-bioaugmented oil-contaminated desert soils. Post-treatment shifts in the soils' bacterial community structure were monitored using MiSeq sequencing. Bacterial respiration, indicated by the amount of evolved CO2, was highest at 10 mM EDTA in bioaugmented and non-bioaugmented soils, reaching an amount of 2.2 ± 0.08 and 1.6 ± 0.02 mg-CO2 g(-1) after 14 days of incubation, respectively. GC-MS revealed that 91.5% of the C14-C30 alkanes were degraded after 42 days when 10 mM EDTA and the bacterial consortium were added together. MiSeq sequencing showed that 78-91% of retrieved sequences in the original soil belonged to Deinococci, Alphaproteobacteria, Gammaproteobacteia and Bacilli. The same bacterial classes were detected in the 10 mM EDTA-treated soils, however with slight differences in their relative abundances. In the bioaugmented soils, only Alcanivorax sp. MH3 and Parvibaculum sp. MH21 from the exogenous bacterial consortium could survive until the end of the experiment. We conclude that the addition of EDTA at appropriate concentrations could facilitate biodegradation processes by increasing hydrocarbon availability to microbes. The addition of exogenous oil-degrading bacteria along with EDTA could serve as an ideal solution for the decontamination of oil-contaminated desert soils. Copyright © 2016 Elsevier Ltd. All rights reserved.

Study on the reutilization of clear fracturing flowback fluids in surfactant flooding with additives for Enhanced Oil Recovery (EOR.

Directory of Open Access Journals (Sweden)

Caili Dai

Full Text Available An investigation was conducted to study the reutilization of clear fracturing flowback fluids composed of viscoelastic surfactants (VES with additives in surfactant flooding, making the process more efficient and cost-effective. The clear fracturing flowback fluids were used as surfactant flooding system with the addition of α-olefin sulfonate (AOS for enhanced oil recovery (EOR. The interfacial activity, emulsification activity and oil recovery capability of the recycling system were studied. The interfacial tension (IFT between recycling system and oil can be reduced by 2 orders of magnitude to 10(-3 mN/m, which satisfies the basic demand of surfactant flooding. The oil can be emulsified and dispersed more easily due to the synergetic effect of VES and AOS. The oil-wet surface of quartz can be easily converted to water-wet through adsorption of surfactants (VES/AOS on the surface. Thirteen core plug flooding tests were conducted to investigate the effects of AOS concentrations, slug sizes and slug types of the recycling system on the incremental oil recovery. The investigations prove that reclaiming clear fracturing flowback fluids after fracturing operation and reuse it in surfactant flooding might have less impact on environment and be more economical.

Behaviors of Polymer Additives Under EHL and Influences of Interactions Between Additives on Friction Modification

Science.gov (United States)

Sakurai, T.

1984-01-01

Polymer additives have become requisite for the formulation of multigrade engine oils. The behavior of polymethacrylate (PMA)-thickened oils as lubricants in concentrated contacts under nominal rolling and pure sliding conditions was investigated by conventional optical interferometry. The PMA thickened oils behaved differently from the base oil in the formation of elastohydrodynamic (EHL) films. The higher the elastohydrodynamic molecular weight of the PMA contained in the lubricant, the thinner was the oil film under EHL conditions. The film thickness of shear-degraded PMA-thickened oils was also investigated. The behavior of graphite particles dispersed in both the base oil and the PMA-thickened oil was studied under pure sliding by taking photomicrographs. Many kinds of additives are contained in lubricating oil and the interactions between additives are considered. The interactions of zinc-organodithiophosphates (ZDP) with other additives is discussed.

Performance Test on Compression Ignition Engine by Blending Ethanol and Waste Plastic Pyrolysis Oil with Cetane Additive

Science.gov (United States)

Padmanabhan, S.; Ganesan, S.; Jeswin Arputhabalan, J.; Chithrala, Varun; Ganesh Bairavan, P.

2017-05-01

The demand for diesel fuel is higher than that of petrol throughout the world hence seeking alternative to mineral diesel is a natural choice. Alternative fuels should be easily available at lower cost, environment friendly and fulfill energy needs without modifying engine’s operational parameters. Waste to energy is the trend in the selection of alternate fuels. In this work, Waste Plastic Pyrolysis oil (WPPO), Ethanol, Diesel blend with Cetane additive has been attempted as an alternative fuel. A Twin cylinder, Direct Injection engine was used to assess the engine performance and emission characteristics of waste plastic pyrolysis oil with cetane additive. Experimental results of blended plastic fuel and diesel fuel were compared.

Effect of lithium salts addition on the ionic liquid based extraction of essential oil from Farfarae Flos.

Science.gov (United States)

Li, Zhen-Yu; Zhang, Sha-Sha; Jie-Xing; Qin, Xue-Mei

2015-01-01

In this study, an ionic liquids (ILs) based extraction approach has been successfully applied to the extraction of essential oil from Farfarae Flos, and the effect of lithium chloride was also investigated. The results indicated that the oil yields can be increased by the ILs, and the extraction time can be reduced significantly (from 4h to 2h), compared with the conventional water distillation. The addition of lithium chloride showed different effect according to the structures of ILs, and the oil yields may be related with the structure of cation, while the chemical compositions of essential oil may be related with the anion. The reduction of extraction time and remarkable higher efficiency (5.41-62.17% improved) by combination of lithium salt and proper ILs supports the suitability of the proposed approach. Copyright © 2014 Elsevier B.V. All rights reserved.

Evaluation of nano emulsion containing asphaltenes dispersant additive in dehydration of oil; Avaliacao de nanoemulsoes contendo aditivo dispersante de asfaltenos na desidratacao de petroleo

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Priscila F. de; Rodrigues, Jessica S.; Mansur, Claudia R.E. [Universidade Federal do Rio de Janeiro/ Instituto de Macromoleculas/ Laboratorio de Macromoleculas e Coloides na Industria de Petroleo, Rio de Janeiro, RJ (Brazil)], e-mail: prisfrias@hotmail.com

2011-07-01

Due to the problem of the formation of emulsions type water-oil during oil production, new alternatives of the breakdown of these emulsions have been proposed over the years. Several polymers have been used to destabilize these emulsions and among them are those based on polyphenylene ether. The aim of this study was to develop nanoemulsions type oil / water, where an asphaltenes dispersant additive was dissolved in dispersed phase in order to evaluate them as a new alternative in the breakdown of oil emulsions. The nanoemulsions were prepared in the presence of surfactant based on polyoxide using a high pressure homogenizer (HPH). We obtained stable nanoemulsions for more than 30 days in the presence or absence of additive. These nanoemulsions were effective in water /oil phase separation, and the nanoemulsion containing the dispersant additive provided a faster separation of these phases. (author)

Influence of Nutrient Impregnated into Zeolite Addition on Anaerobic Digestion of Palm Oil Mill Effluent (POME)

Science.gov (United States)

Mellyanawaty, M.; Chusna, F. M. A.; Sudibyo, H.; Nurjanah, N.; Budhijanto, W.

2018-03-01

Palm oil mill effluent (POME) was wastewater generated from palm oil milling activities which was brownish liquid, acidic with pH 3-4, and contained soluble materials which were hazardous to the environment. It was characterized by high organic loading (COD 40,000–60,000 mg/L). According to its characteristics, POME was identified as a potential source to generate renewable energy through anaerobic digestion. In other words, a combination of wastewater treatment and renewable energy production would be an additional advantage to the palm oil industries. Methanogenesis was the rate limiting step in anaerobic digestion. In the conventional anaerobic digester, it required large reactors and long retention time. The addition of microbial immobilization media was to improve anaerobic reactor performance in term of higher organic removal and methane production. Additionally, better performance could lead to reduction of reactor volume and shorter retention time in high rate anaerobic digester. The loading of essential microorganism nutrient into the media might increase the affinity of bacteria to attach and grow on the media surface. Activating or inhibition effects of natural and modified zeolite addition in anaerobic digestion of POME was studied in batch reactors using erlenmeyer of 1,000 mL at COD concentrations of about 8,000 mg/L. Zeolite was impregnated with nickel and magnesium at concentrations of 0.0561 mg Ni/g zeolite and 0.0108 mg Mg/g zeolite. The effect of the different zeolite addition was determined by the measurement of soluble COD (sCOD), Volatile Fatty Acids (VFAs) and biogas production. Greater effect of modified zeolite was observed in zeolite impregnated with nickel with a 54% increase of biogas production. Meanwhile, the modified zeolite impregnated with magnesium had no positive impact to the methanogenic bacteria activities.

Waste fatty acid addition to black liquor to decrease tall oil soap solubility and increase skimming efficiency in kraft mills pulping mountain pine beetle-infested wood

Energy Technology Data Exchange (ETDEWEB)

Uloth, V.; Guy, E. [FPInnovations, Prince George, BC (Canada). PAPRICAN Div.; Shewchuk, D. [Cariboo Pulp and Paper, Quesnel, BC (Canada); Van Heek, R. [Aker Kvaerner, Vancouver, BC (Canada)

2009-07-01

This paper presented the results of tests conducted to determine if the addition of waste fatty acids from vegetable oil processing might decrease tall oil soap solubility in pine-beetle impacted wood from British Columbia (BC). The soap recovery and tall oil production at BC mills has fallen by 30 to 40 percent in recent years due to the pulping of high proportions of grey-stage beetle-impacted wood. Full-scale mill tests were conducted over a 4-day period. The study showed that the addition of tall oil fatty acids or waste fatty acids from vegetable oil processing could decrease tall oil soap solubility and increase the soup skimming efficiency in mills pulping a large percentage of grey stage beetle-infested wood. The addition of fatty acids increased tall oil soap skimming efficiency from 50.2 percent in the baseline tests to 71.8 percent based on the total soap available, and from 76.7 percent in the baseline tests to 87.5 percent based on insoluble soap only. The economic analyses indicated that waste fatty acid addition could be economical when natural gas and oil prices are high. 4 tabs., 9 figs.

Socializing the Addition of Jambal Siam (Pangasius hypophtalmus) Fish Stomach Oil and Kerapu (Cromileptes sp) Fish Oil in Baby Porridge for Satisfy Omega 3 and Omega 6 Standard

OpenAIRE

Mirna Ilza; Yusni Ikhwan Siregar

2015-01-01

The research aim on the socialization of the addition of jambal siam (Pangasius hypophtalmus)fish stomach oil and kerapu (Cromileptes sp) fish oil in baby porridge for satisfy omega 3 and omega6 standard was implemented around Pekanbaru and Bangkinang (Kampar district). The additionof fish oil is done based on the standard of the WHO weight which conform to the age of the baby.The baby’s weight is very less than WHO standard dose given 50 mg/day, less weight given 40 mg/day, and normal weight...

Exhaust emissions reduction from diesel engine using combined Annona-Eucalyptus oil blends and antioxidant additive

Science.gov (United States)

Senthil, R.; Silambarasan, R.; Pranesh, G.

2017-03-01

The limited resources, rising petroleum prices and depletion of fossil fuel have now become a matter of great concern. Hence, there is an urgent need for researchers to find some alternate fuels which are capable of substituting partly or wholly the higher demanded conventional diesel fuel. Lot of research work has been conducted on diesel engine using biodiesel and its blends with diesel as an alternate fuel. Very few works have been done with combination of biodiesel-Eucalypts oil without neat diesel and this leads to lots of scope in this area. The aim of the present study is to analyze the performance and emission characteristics of a single cylinder, direct injection, compression ignition engine using eucalyptus oil-biodiesel as fuel. The presence of eucalyptus oil in the blend reduces the viscosity and improves the volatility of the blends. The methyl ester of Annona oil is blended with eucalypts oil in 10, 20, 30, 40 and 50 %. The performance and emission characteristics are evaluated by operating the engine at different loads. The performance characteristics such as brake thermal efficiency, brake specific fuel consumption and exhaust gas temperature are evaluated. The emission constituents measured are Carbon monoxide (CO), unburned hydrocarbons (HC), Oxides of nitrogen (NOx) and Smoke. It is found that A50-Eu50 (50 Annona + 50 % Eucalyptus oil) blend showed better performance and reduction in exhaust emissions. But, it showed a very marginal increase in NOx emission when compared to that of diesel. Therefore, in order to reduce the NOx emission, antioxidant additive (A-tocopherol acetate) is mixed with Annona-Eucalyptus oil blends in various proportions by which NOx emission is reduced. Hence, A50-Eu50 blend can be used as an alternate fuel for diesel engine without any modifications.

Viscosity modification of high-oleic sunflower oil with polymeric additives for the design of new biolubricant formulations.

Science.gov (United States)

Quinchia, L A; Delgado, M A; Valencia, C; Franco, J M; Gallegos, C

2009-03-15

Although most common lubricants contain mineral or synthetic oils as basestocks, new environmental regulations are demanding environmentally friendly lubricants. In this sense, vegetable oils represent promising alternatives to mineral-based lubricants because of their high biodegradability, good lubricity, and low volatility. However, their poor thermooxidative stability and the small range of viscosity represent a clear disadvantage to be used as suitable biolubricants. The main objective of this work was to develop new environmentally friendly lubricant formulations with improved kinematic viscosity values and viscosity thermal susceptibility. With this aim, a high-oleic sunflower oil (HOSO) was blended with polymeric additives, such as ethylene vinyl acetate (EVA) and styrene-butadiene-styrene (SBS) copolymers, at different concentrations (0.5-5% w/w). Dynamic viscosity and density measurements were performed in a rotational rheometer and capillary densimeter, respectively, in a temperature range between 25 and 120 degrees C. An Arrhenius-like equation fits the evolution of viscosity with temperature fairly well. Both EVA and SBS copolymers may be satisfactorily used as additives to increase the viscosity of HOSO, thus improving the low viscosity values of this oil. HOSO viscosity increases with polymer concentration. Specifically, EVA/HOSO blends exhibit higher viscosity values, which are needed for applications such as lubrication of bearings and four-stroke engines. On the other hand, viscositythermal susceptibility of HOSO samples increases with EVA or SBS concentration.

Can reserve additions in mature crude oil provinces attenuate peak oil?

NARCIS (Netherlands)

Okullo, S.J.; Reynes, F.G.D.

2011-01-01

Following the peak in US crude oil production 30 years ago, more and more non-OPEC producers have seen their production decline as a result of resource depletion. OPEC, on the other hand has extracted a comparatively smaller proportion of its reserve base. Given that new non-OPEC discoveries are

Heat-transfer, inside of the ground heat-transfer units, from liquid, additionally cooling the oil-immersed transformer

OpenAIRE

Madyshev Ilnur; Dmitrieva Oksana; Dmitriev Andrey

2017-01-01

A device for cooling the oil-immersed transformer by means of thermoelectric transducers has been developed. Their operating principle is based on the fact that at night at minimum ambient temperature, the cold is accumulated inside of a vessel due to formation of water ice layer on the developed surfaces of thermoelectric transducers` ribs. Melting of this layer is used in the hottest time of a day for additional cooling of transformer oil in the cooling system of the transformer. Pre-coolin...

Measurement of the effect of an oil additive on vibration, noise and smokiness

International Nuclear Information System (INIS)

Dimitrovski, M.

1999-01-01

The contents of this article provides a analysis of vibration, noise and smokiness in compression ignition engines. Further explanation has been given on types of lubrication and oils with their characteristic. Series of experiments has been conducted on vibration. Noise and smokiness before and after adding additive. Presentation has been given of data obtained from examination of the vehicle. At the end comparison of data analysis and conclusion has been done. (Author)

HOW PROPERTIES OF EDIBLE OILS ARE IMPROVED BY ESSENTIAL OILS

Directory of Open Access Journals (Sweden)

SONIA AMARIEI

2016-10-01

Full Text Available The main aim of the present paper is to find out whether the addition of essential oils determines better oxidation stability and positive change of sensory and hedonic perception of edible oils. The oxidation stability of sunflower, corn and grape seed oils was analyzed in the presence of antioxidants in essential oils of rosemary (Rosmarinus officinalis, thyme (Thymus vulgaris and basil (Ocimum basilicum during storage, under conditions of accelerated oxidative processes (4 days, at 60 °C. The total phenolic compounds of these essential oils were determined by the Folin-Ciocalteu method. The DPPH method was used to evaluate the antioxidant capacity of basil, rosemary and thyme essential oils in comparison with known synthetic antioxidant L(+-ascorbic acid. The addition of essential oils to edible oils, the amounts proposed in analyses, determines a favorable influence on their oxidation stability as well as their taste. The influence of addition of essential oils on the taste of edible oils was studied in two products consumed mainly at breakfast, bread and spinach leaves. The results recommend the use of these plant extracts as additives in edible oils rather than synthetic antioxidants.

Effect of the addition of ultraviolet absorber (Tinuvin 234) on the quality of soybean oil packaged in polyethylene terephthalate (PET)

International Nuclear Information System (INIS)

Oliveira Alves, M.A. de; Arruda, C.S.; Ogliari, P.J.; Meinert, E.M.; Teixeira, E.; Barrera-Arellano, D.; Block, J.M.

2005-01-01

In this work, the effect of the addition of the UV absorber Tinuvin 234 on the quality of soybean oil packaged in PET bottles stored at ambient temperature for 6 months under fluorescent light (634 lux). Along this period determinations were made of: peroxide value (PV), free fatty acids (FFA), specific extinction at 232 and 270 nm (EE) and sensorial evaluation (SE). The analysis of variance and resistance between the linear coefficients of each treatment indicates that significant difference does not exist (p0.0001) during the storage in relation to all determinations (PV, FFA, EE and SE). The results indicate that the addition of the absorbent Tinuvin 234 to PET bottles in the concentrations of 0.12% and 0.22% was not efficient in slowing down the deterioration of the oil exposed to the fluorescent light, when compared with soybean oil in PET bottles without addition of Tinuvin 234. (author) [es

Improvement of phenolic antioxidants and quality characteristics of virgin olive oil with the addition of enzymes and nitrogen during olive paste processing

Energy Technology Data Exchange (ETDEWEB)

Inconomou, D.; Arapoglou, D.; Israilides, C.

2010-07-01

The evolution of phenolic compounds and their contribution to the quality characteristics in virgin olive oil during fruit processing was studied with the addition of a combination of various commercial enzymes containing pectinases, polygalacturonases, cellulase and {beta}-glucanase with or without nitrogen flush. Olive fruits (Olea europaea, L.) of the cultivar Megaritiki, at the semi black pigmentation stage of maturity, were used in a 3-phase extraction system in an experiment at industrial scale. The addition of enzymes in the olive paste during processing increased the total phenol and ortho-diphenol contents, as well as some simple phenolic compounds (3,4-DHPEA, p-HPEA) and the secoiridoid derivatives (3,4-DHPEA-EDA and 3,4-DHPEAEA) in olive oil and therefore improved its oxidative stability. Furthermore, enzyme treatment ameliorated the quality parameters of the produced olive oil (acidity and peroxide value) and their sensory attributes. The use of additional N{sub 2} flush with the enzyme treatments did not improve the quality parameters of olive oil any further; however it did not affect the concentration of individual and total sterols or most of the fatty acid composition. Consequently, olive paste treatment with enzymes not only improved the quality characteristics of olive oil and enhanced the overall organoleptic quality, but also increased the olive oil yield. (Author) 33 refs.

Study of effects of engine oil additives on the properties of fluorelastomers; Fusso gomu ni oyobosu engine yu tenkazai no eikyo chosa

Energy Technology Data Exchange (ETDEWEB)

Kurono, K; Owaki, M; Suzuki, Y; Akiyama, K; Shionoya, M [Toyota Motor Corp., Aichi (Japan)

1997-10-01

Fluoroelastmers are well known for their resistance to heat and fluids and have become major material for crankcase oil sealers. On the other hand new additive formulations are developed for engine lubricants used for fuel economic gasoline engines. In this paper the effects of those additives on properties of fluoroelastmers are investigated. The results of the immersion tests of both test plaques and oil sealer products indicates that dithiocarbamates friction modifier have hardening effects on fluoroelastomers. The fluoroelastmer deterioration mechanism is presumed by analysis of elastmer samples after immersion in oil. 6 refs., 9 figs., 3 tabs.

How the Addition of Spices and Herbs to Virgin Olive Oil to Produce Flavored Oils Affects Consumer Acceptance.

Science.gov (United States)

Issaoui, Manel; Flamini, Guido; Souid, Sondess; Bendini, Alessandra; Barbieri, Sara; Gharbi, Ines; Toschi, Tullia Gallina; Cioni, Pier Luigi; Hammami, Mohamed

2016-06-01

With the aim to expand the olive oil market to a larger number of consumers who are not familiar with the sensory characteristics of virgin olive oil, the use of novel products known as "flavored olive oils", obtained by adding different kind of spices and aromatic herbs, is spreading in many countries. In order to test consumer acceptability of this type of product, in a country (Tunisia) in which virgin olive oil is regularly consumed, flavored olive oils were prepared by adding aromatic extracts of thyme, oregano, a mix of herbs (used as pizza seasoning), rosemary, and basil to a monovarietal Chemlali virgin olive oil and a consumer test on 206 subjects was performed. Selected quality parameters (free acidity, peroxide number, oxidative stability, specific absorption at K232 nm and K270 nm) were also measured and no significant variations were detected. Slight differences were found concerning the content of minor compounds (chlorophylls, carotenoids and total phenols). On the other hand, notable differences were seen in the profiles of volatile compounds, which appeared to be responsible for the observed variability in consumer acceptance. Although the unflavored oil was more appreciated than the flavored ones, among the latter, thyme flavored olive oil was the most appreciated.

Modification of Lightweight Aggregates’ Microstructure by Used Motor Oil Addition

Science.gov (United States)

Franus, Małgorzata; Jozefaciuk, Grzegorz; Bandura, Lidia; Lamorski, Krzysztof; Hajnos, Mieczysław; Franus, Wojciech

2016-01-01

An admixture of lightweight aggregate substrates (beidellitic clay containing 10 wt % of natural clinoptilolite or Na-P1 zeolite) with used motor oil (1 wt %–8 wt %) caused marked changes in the aggregates’ microstructure, measured by a combination of mercury porosimetry (MIP), microtomography (MT), and scanning electron microscopy. Maximum porosity was produced at low (1%–2%) oil concentrations and it dropped at higher concentrations, opposite to the aggregates’ bulk density. Average pore radii, measured by MIP, decreased with an increasing oil concentration, whereas larger (MT) pore sizes tended to increase. Fractal dimension, derived from MIP data, changed similarly to the MIP pore radius, while that derived from MT remained unaltered. Solid phase density, measured by helium pycnometry, initially dropped slightly and then increased with the amount of oil added, which was most probably connected to changes in the formation of extremely small closed pores that were not available for He atoms. PMID:28773964

Modification of Lightweight Aggregates’ Microstructure by Used Motor Oil Addition

Directory of Open Access Journals (Sweden)

Małgorzata Franus

2016-10-01

Full Text Available An admixture of lightweight aggregate substrates (beidellitic clay containing 10 wt % of natural clinoptilolite or Na-P1 zeolite with used motor oil (1 wt %–8 wt % caused marked changes in the aggregates’ microstructure, measured by a combination of mercury porosimetry (MIP, microtomography (MT, and scanning electron microscopy. Maximum porosity was produced at low (1%–2% oil concentrations and it dropped at higher concentrations, opposite to the aggregates’ bulk density. Average pore radii, measured by MIP, decreased with an increasing oil concentration, whereas larger (MT pore sizes tended to increase. Fractal dimension, derived from MIP data, changed similarly to the MIP pore radius, while that derived from MT remained unaltered. Solid phase density, measured by helium pycnometry, initially dropped slightly and then increased with the amount of oil added, which was most probably connected to changes in the formation of extremely small closed pores that were not available for He atoms.

21 CFR 172.861 - Cocoa butter substitute from coconut oil, palm kernel oil, or both oils.

Science.gov (United States)

2010-04-01

... kernel oil, or both oils. 172.861 Section 172.861 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT... substitute from coconut oil, palm kernel oil, or both oils. The food additive, cocoa butter substitute from coconut oil, palm kernel oil, or both oils, may be safely used in food in accordance with the following...

Effects of the addition of oil shale ash and coal ash on physic-chemical properties of CPJ45 cement

Directory of Open Access Journals (Sweden)

Nabih K.

2014-04-01

Full Text Available We focused our research on recycling industrial wastes, fly ash (F.A, bottom ash (B.A and oil shale ash (S.A in cement production. The study concerns physico-chemical characterization of these products and the influence of their addition on the mechanical proprieties of the CPJ45 cement. XRF allowed us to rank the three additives used according to their contents on major oxides. Coal ashes belong to the class F, and thus possess poozzolanic properties and oil shale ash belongs to the class C and possesses hydraulic and poozolanic properties. The crystalline phases constituting each ash were analysed by XRD. We observe in bottom ash the presence of quartz and mullite. The same crystals are found in fly ash with hematite and magnetite. Oil shale ash is composed of quartz, anhydrite, gehlenite, wollastonite and periclase. The microstructures of fly ash and bottom ash were studied using SEM. The bottom ash was composed respectively of fine particles that are generally irregularly shaped, their dimensions are between 5 and 28μm and of big particles(300 μm. The EDX analysis coupled with an electronic microscope provided some information about the major elements that constitute our samples. The dehydrations of anhydrous and three days hydrated cement were examined by DSC. For hydrated cements we noticed endothermic peaks related to the dehydration of CSH, CH and decomposition of carbonates. The study of the mechanical properties of CPJ45 cement by adding different proportions of fly ash, bottom ash and oil shale ash helped clarifying the percentage of ash that leaded to improve the 28 days mechanical strength. The results show that the cements studied have their maximum mechanical resistance with the addition at 7% of fly ash or 10% of oil shale ash.

DRAGON FRUIT JUICE ADDITION IN PALM OIL-PUMPKIN EMULSION: PANELIST ACCEPTANCE AND ANTIOXIDANT CAPACITY

Directory of Open Access Journals (Sweden)

Anton Rahmadi*

2017-12-01

Full Text Available Addition of dragon juice to emulsion products formulated from olein fraction of red palm oil and pumpkin juice was conducted as an effort to improve the taste thus it can be accepted by consumers. This study aims to (1 observe the acceptance of 60 panelists aged 17-21 years on the parameters of taste, aroma, mouthfeel, color, flavor and aroma of each contributing components of dragon fruit, palm oil, and raspberry flavor with the addition of dragon fruit juice at level 0 (control, 25, 50, and 75% (v/v, and (2 observe the changes in chemical components i.e. vitamin C and total titrable acids, total carotenoid by spectrophotometry, and antioxidant activity by 2,2-diphenyl-1-picrylhdrazyl (DPPH reduction method. The best formula was the one containing 75% (v/v of red dragon juice in fresh condition with vitamin C content of 19.32±0.62 mg/100 mL, antioxidant activity of 354.25±0.77 ppm, hedonic color, taste, and viscosity between favorable and very favorable. After 2 weeks of storage at room temperature (28±2ºC, the vitamin C, total carotene, and antioxidant activity of the mixture decreased by 29.72, 15.44, and 46.59%, res-pectively.

MEA and DEE as additives on diesel engine using waste plastic oil diesel blends

Directory of Open Access Journals (Sweden)

Pappula Bridjesh

2018-05-01

Full Text Available Waste plastic oil (WPO is a standout amongst the most promising alternative fuels for diesel in view of most of its properties similar to diesel. The challenges of waste management and increasing fuel crisis can be addressed while with the production of fuel from plastic wastes. This experimental investigation is an endeavour to supplant diesel at least by 50% with waste plastic oil alongside 2-methoxy ethyl acetate (MEA and diethyl ether (DEE as additives. Test fuels considered in this study are WPO, 50D50W (50%Diesel + 50%WPO, 50D40W10MEA (50%Diesel + 40%WPO + 10%MEA and 50D40W10DEE (50%Diesel + 40%WPO + 10%DEE. The test results are compared with diesel. An increase in brake thermal efficiency and abatement in brake specific fuel consumption are seen with 50D40W10MEA, as well as reduction in hydro carbon, carbon monoxide and smoke emissions. 50D40W10DEE showed reduced NOx emission whereas 50D40W10MEA has almost no impact. Engine performance and emission characteristics under different loads for different test fuels are discussed. Keywords: 2-Methoxy ethyl acetate, Diethyl ether, Waste plastic oil, Pyrolysis

Jatropha Oil Derived Sophorolipids: Production and Characterization as Laundry Detergent Additive

OpenAIRE

Joshi-Navare, Kasturi; Khanvilkar, Poonam; Prabhune, Asmita

2013-01-01

Sophorolipids (SLs) are glycolipidic biosurfactants suitable for various biological and physicochemical applications. The nonedible Jatropha oil has been checked as the alternative raw material for SL synthesis using C. bombicola (ATCC22214). This is useful towards lowering the SL production cost. Through optimization of fermentation parameters and use of resting cell method, the yield 15.25 g/L could be achieved for Jatropha oil derived SL (SLJO) with 1% v/v oil feeding. The synthesized SL d...

Essential Oil of Common Thyme as a Natural Antimicrobial Food Additive

Directory of Open Access Journals (Sweden)

Jasna Dolenc Koce

2014-01-01

Full Text Available Antimicrobial activities of thyme essential oil against selected microorganisms, including Fusarium sp., Armillaria mellea, Bacillus cereus, Staphylococcus aureus, Buttiauxella sp., Klebsiella pneumoniae, Escherichia coli K-12, AmpC-producing E. coli Z, ESBL-producing E. coli strain of KM clonal group ST131, and E. coli 1138 were evaluated. The antimicrobial efficacy of thyme essential oil was determined using agar well diffusion assays. The growth of all tested bacteria was inhibited at thyme essential oil fractions higher than 1 %, while a fraction of 10 % was needed to inhibit the growth of fungi. We demonstrate that thyme essential oil has a promising activity against food spoilage bacteria, and also against multiresistant AmpC-producing and ESBL-producing bacterial strains isolated from food, which have recently been recognised as public health concerns. On the basis of our data, the thyme essential oil has a potential for use as a growth inhibitor of multidrug-resistant bacteria, and food spoilage and pathogenic bacteria and fungi, to replace commonly used semi-synthetic antimicrobial products.

The influence of bioaugmentation and biosurfactant addition on bioremediation efficiency of diesel-oil contaminated soil: feasibility during field studies.

Science.gov (United States)

Szulc, Alicja; Ambrożewicz, Damian; Sydow, Mateusz; Ławniczak, Łukasz; Piotrowska-Cyplik, Agnieszka; Marecik, Roman; Chrzanowski, Łukasz

2014-01-01

The study focused on assessing the influence of bioaugmentation and addition of rhamnolipids on diesel oil biodegradation efficiency during field studies. Initial laboratory studies (measurement of emitted CO2 and dehydrogenase activity) were carried out in order to select the consortium for bioaugmentation as well as to evaluate the most appropriate concentration of rhamnolipids. The selected consortium consisted of following bacterial taxa: Aeromonas hydrophila, Alcaligenes xylosoxidans, Gordonia sp., Pseudomonas fluorescens, Pseudomonas putida, Rhodococcus equi, Stenotrophomonas maltophilia, Xanthomonas sp. It was established that the application of rhamnolipids at 150 mg/kg of soil was most appropriate in terms of dehydrogenase activity. Based on the obtained results, four treatment methods were designed and tested during 365 days of field studies: I) natural attenuation; II) addition of rhamnolipids; III) bioaugmentation; IV) bioaugmentation and addition of rhamnolipids. It was observed that bioaugmentation contributed to the highest diesel oil biodegradation efficiency, whereas the addition of rhamnolipids did not notably influence the treatment process. Copyright © 2013 Elsevier Ltd. All rights reserved.

The influence of additives on leaching of tritium of the immobilization matrices of contaminated oils by cementation

International Nuclear Information System (INIS)

Deneanu, N.; Dulama, M.; Baboescu, E.; Horhoianu, G.

2000-01-01

The research studies showed that the solidification of contaminated pump oils resulted from Cernavoda NPP operation can be done by using various immobilization matrices such as: cement with appropriate mineral additives sand of Aghires, lime and silicate accelerator. Research works and experiments were carried out on four groups: cement-emulsion, cement-emulsion-silicate accelerator, cement-emulsion-lime- silicate accelerator and cement-emulsion-sand of Aghires. The paper presents the author's research on immobilization of contaminated oil by cementation using Romanian emulsifiers. With both of the emulsifiers used, there were obtained reasonable compressive strengths and leaching rates. (author)

Radiation Protection and the Management of Radioactive Waste in the Oil and Gas Industry. Additional Information

International Nuclear Information System (INIS)

2010-01-01

The oil and gas industry, a global industry operating in many Member States, makes extensive use of radiation generators and sealed and unsealed radioactive sources, some of which are potentially dangerous to human health and the environment if not properly controlled. In addition, significant quantities of naturally occurring radioactive material (NORM) originating from the reservoir rock are encountered during production, maintenance and decommissioning. The oil and gas industry operates in all climates and environments, including the most arduous conditions, and is continuously challenged to achieve high efficiency of operation while maintaining a high standard of safety and control - this includes the need to maintain control over occupational exposures to radiation, as well as to protect the public and the environment through proper management of wastes that may be radiologically and chemically hazardous. The oil and gas industry is organizationally and technically complex, and relies heavily on specialized service and supply companies to provide the necessary equipment and expertise, including expertise in radiation safety. This training manual is used by the IAEA as the basis for delivering its training course on radiation protection and the management of radioactive waste in the oil and gas industry. Enclosed with this manual is a CD-ROM that contains the presentational material used in the training course, the course syllabus and additional notes for course presenters. The course material is based principally on IAEA Safety Reports Series No. 34 Radiation Protection and the Management of Radioactive Waste in the Oil and Gas Industry, published by the IAEA in 2003. The training course is aimed at regulatory bodies; oil and gas field operators and support companies; workers and their representatives; health, safety and environmental professionals; and health and safety training officers. A pilot training course was held in the Syrian Arab Republic in 2000 as

Enhanced treatment of waste frying oil in an activated sludge system by addition of crude rhamnolipid solution.

Science.gov (United States)

Zhang, Hongzi; Xiang, Hai; Zhang, Guoliang; Cao, Xia; Meng, Qing

2009-08-15

The presence of high-strength oil and grease (O&G) in wastewater poses serious challenges for environment. Addition of surfactant into the activated sludge bioreactor is feasible in reducing high concentrations of O&G via enhancing its bioavailability. In this paper, an aqueous biosurfactant solution of rhamnolipid as a cell-free culture broth of Pseudomonas aeruginosa zju.um1 was added into a batch of aerobic activated sludge system for treatment of the waste frying oil. This treatment was conducted on both bench and pilot-scales, whereas the removal efficiency of frying oil was determined by analyzing the residue concentration of O&G and chemical oxygen demand (COD). In the presence of varying concentrations of rhamnolipid from 22.5 mg/L to 90 mg/L, aerobic treatment for 30 h was enough to remove over 93% of O&G while this biodegradability was only 10% in the control system with the absence of rhamnolipids. The equivalent biodegradability was similarly obtained on COD under addition of rhamnolipid. Compared with bench studies, a higher treatment efficiency with the presence of rhamnolipids was achieved on a pilot-scale of activated sludge system, in which a short time of 12h was required for removing approximately 95% of O&G while the control treatment attained a low efficiency of 17%. Finally, foaming and biodegradability of rhamnolipids in activated sludge system were further examined in the whole treatment process. It seems that the addition of rhamnolipid-containing culture broth showed great potential for treatment of oily wastewater by activated sludge.

Enhanced treatment of waste frying oil in an activated sludge system by addition of crude rhamnolipid solution

International Nuclear Information System (INIS)

Zhang Hongzi; Xiang Hai; Zhang Guoliang; Cao Xia; Meng Qing

2009-01-01

The presence of high-strength oil and grease (O and G) in wastewater poses serious challenges for environment. Addition of surfactant into the activated sludge bioreactor is feasible in reducing high concentrations of O and G via enhancing its bioavailability. In this paper, an aqueous biosurfactant solution of rhamnolipid as a cell-free culture broth of Pseudomonas aeruginosa zju.um1 was added into a batch of aerobic activated sludge system for treatment of the waste frying oil. This treatment was conducted on both bench and pilot-scales, whereas the removal efficiency of frying oil was determined by analyzing the residue concentration of O and G and chemical oxygen demand (COD). In the presence of varying concentrations of rhamnolipid from 22.5 mg/L to 90 mg/L, aerobic treatment for 30 h was enough to remove over 93% of O and G while this biodegradability was only 10% in the control system with the absence of rhamnolipids. The equivalent biodegradability was similarly obtained on COD under addition of rhamnolipid. Compared with bench studies, a higher treatment efficiency with the presence of rhamnolipids was achieved on a pilot-scale of activated sludge system, in which a short time of 12 h was required for removing approximately 95% of O and G while the control treatment attained a low efficiency of 17%. Finally, foaming and biodegradability of rhamnolipids in activated sludge system were further examined in the whole treatment process. It seems that the addition of rhamnolipid-containing culture broth showed great potential for treatment of oily wastewater by activated sludge.

Improvement of liquefaction solvent. Increase of light oil yield with a reduction in catalyst addition; Ekika yozai no kairyo kenkyu. Sekitan ekikayu no keishitsuka to shokubai tenkaryo no teigen

Energy Technology Data Exchange (ETDEWEB)

Okuyama, N.; Yasumuro, M.; Sato, K.; Komatsu, N.; Okui, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan)

1996-10-28

For developing coal liquefaction processes, it is an important problem to improve the light oil yield with increased oil yield. It was previously reported that distillate mainly containing lighter fraction can be produced with high oil yield by reducing the iron/sulfur catalyst addition in slurry, by recycling gas in the process operation, by utilizing these effects, and by using heavy oil as recycling solvent. In this study, the maximum distillate yield of Victorian brown coal was investigated through continuous liquefaction using a bench scale unit. In addition, operation conditions for obtaining sufficient oil yield were investigated under the reduced catalyst addition into one-third. Consequently, it was confirmed that the maximum content of lighter fraction in distillate product was obtained with reduced catalyst addition by using heavy oil as recycling solvent, by adopting new catalyst, and by utilizing effects of CLB recycling and gas recycling in maximum. It was also revealed that lighter distillate can be produced compared with the oil product obtained by recycling conventional solvent. 3 refs., 6 figs., 2 tabs.

Method for the validation and uncertainty estimation of tocopherol analysis applied to soybean oil with addition of spices and TBHQ

Directory of Open Access Journals (Sweden)

da Silva, M. G.

2013-09-01

Full Text Available The tocopherol contents of refined soybean oil with the addition of rosemary, oregano, garlic, annatto seeds and TBHQ was evaluated during storage at 25 °C and 35 °C for twelve months, in comparison with a control soybean oil without the antioxidant addition. The method proposed to assess the tocopherol content was validated and the uncertainty estimation was determined. The method presented adequate linearity and precision, accuracy between 93% and 103% and expanded uncertainty of 2%. The contents of α-, γ- and δ-tocopherols of all the tested soybean oils remained constant during the storage at 25 °C and 35 °C regardless of antioxidant addition, while β-tocopherol content decreased. The addition of a mixture of rosemary, oregano, garlic and annatto seeds increased the concentration of γ- and δ-tocopherol. The oil with spices presented a similar behavior to that of the oil with the addition of TBHQ.La concentración de tocoferoles en aceite de soja refinado (muestra control, aceite de soja adicionado de romero, orégano, ajo, semilla de achiote y TBHQ fueron cuantificados durante el almacenamiento durante 12 meses a 25°C y 35°C. El método propuesto para medir tocoferoles fue validado y determinada la incertidumbre. Este método presentó linealidad y precisión adecuadas, exactitud entre 93% y 103% además de una incertidumbre expandida de 2%. Las cantidades de α-, γ- y δ-tocoferol en el aceite de soja refinado, aceite de soja adicionado de condimentos y aceite de soja adicionado con TBHQ se mantuvieron constantes durante el almacenamiento a 25°C y 35°C con excepción del β-tocoferol el cual disminuyó. El aceite de soja adicionado de condimentos (romero, orégano, ajo, y semilla de achiote presentó mayores concentraciones de γ- y δ-tocoferol en comparación con el aceite de soja refinado utilizado como control. El aceite de soja adicionado de condimentos presentó un comportamiento semejante al aceite de soja adicionado

Effect of the addition of fatty by-products from the refining of vegetable oil on methane production in co-digestion.

Science.gov (United States)

Torrijos, M; Sousbie, P; Badey, L; Bosque, F; Steyer, J P

2012-01-01

The purpose of this work was to investigate the effects of the addition of by-products from the refining of vegetable oil on the behavior of co-digestion reactors treating a mixture of grass, cow dung and fruit and vegetable waste. Three by-products were used: one soapstock, one used winterization earth and one skimming of aeroflotation of the effluents. Three 15 l reactors were run in parallel and fed five times a week. In a first phase of 4 weeks, the three reactors were fed with the co-digestion substrates alone (grass, cow dung and fruit and vegetable waste) at an organic loading rate (OLR) of 1.5 g VS/kg d (VS: volatile solids). Then, a different by-product from the refining of oil was added to the feed of each reactor at an OLR of 0.5 g VS/kg d, generating a 33% increase in the OLR. The results show that the addition of by-products from the refining of oil is an efficient way of increasing the methane production of co-digestion reactors thanks to high methane yield of such by-products (0.69-0.77 l CH(4)/g VS loaded). In fact, in this work, it was possible to raise the methane production of the reactors by about 60% through a 33% increase in the OLR thanks to the addition of the by-products from the refining of vegetable oil.

A study of the components of an active substance of high alkaline alkylsalicylate oil additives

Energy Technology Data Exchange (ETDEWEB)

Kravchuk, G G; Glavati, O L; Glavati, Ye V; Zhurba, A S

1981-01-01

The active substance of aklylsalicylate additives (Pr) MACK, dispersal-1 and AS-6OC (from Shell Oil) is isolated and studied. It is shown that the Pr is provided by the presence of both a neutral salicylate, as well as that of a high alkaline component (colloid CaCtheta/sub 3/, stabilized by salicylate). The free alkylphenols present in the Pr do not deteriorate its quality.

Effects of antioxidant additives on exhaust emissions reduction in compression ignition engine fueled with methyl ester of annona oil

Directory of Open Access Journals (Sweden)

Ramalingam Senthil

2016-01-01

Full Text Available In this present study, biodiesel is a cleaner burning alternative fuel to the Neat diesel fuel. However, several studies are pointed out that increase in NOx emission for biodiesel when compared with the Neat diesel fuel. The aim of the present study is to analyze the effect of antioxidant (p-phenylenediamine on engine emissions of a Diesel engine fuelled with methyl ester of annona oil. The antioxidant is mixed in various concentrations (0.010 to 0.040% (w/w with methyl ester of annona oil. Result shows that antioxidant additive mixture (MEAO+P200 is effective in control of NOx and HC emission of methyl ester of annona oil fuelled engine without doing any engine modification.

Oregano Essential Oil as an Antimicrobial and Antioxidant Additive in Food Products.

Science.gov (United States)

Rodriguez-Garcia, I; Silva-Espinoza, B A; Ortega-Ramirez, L A; Leyva, J M; Siddiqui, M W; Cruz-Valenzuela, M R; Gonzalez-Aguilar, G A; Ayala-Zavala, J F

2016-07-26

Food consumers and industries urged the need of natural alternatives to assure food safety and quality. As a response, the use of natural compounds from herbs and spices is an alternative to synthetic additives associated with toxic problems. This review discusses the antimicrobial and antioxidant activity of oregano essential oil (OEO) and its potential as a food additive. Oregano is a plant that has been used as a food seasoning since ancient times. The common name of oregano is given to several species: Origanum (family: Lamiaceae) and Lippia (family: Verbenaceae), amongst others. The main compounds identified in the different OEOs are carvacrol and thymol, which are responsible for the characteristic odor, antimicrobial, and antioxidant activity; however, their content may vary according to the species, harvesting season, and geographical sources. These substances as antibacterial agents make the cell membrane permeable due to its impregnation in the hydrophobic domains, this effect is higher against gram positive bacteria. In addition, the OEO has antioxidant properties effective in retarding the process of lipid peroxidation in fatty foods, and scavenging free radicals. In this perspective, the present review analyzes and discusses the state of the art about the actual and potential uses of OEO as an antimicrobial and antioxidant food additives.

Microbiological and physicochemical characterization of dry-cured Halal goat meat. Effect of salting time and addition of olive oil and paprika covering.

Science.gov (United States)

Cherroud, Sanâa; Cachaldora, Aida; Fonseca, Sonia; Laglaoui, Amin; Carballo, Javier; Franco, Inmaculada

2014-10-01

The objective of this work was to define a simple technological process for dry-cured Halal goat meat elaboration. The aims of this study were to analyze physicochemical parameters and to enumerate the microbial population at the end of the different manufacturing processes (two salting times and the addition of olive oil and paprika covering) on 36 units of meat product. A total of 532 strains were isolated from several selective culture media and then identified using classical and molecular methods. In general, salt effect and the addition of olive oil and paprika were significant for all the studied microbial groups as well as on NaCl content and water activity. Molecular analysis proves that staphylococci, especially Staphylococcus xylosus and Staphylococcus equorum, were the most common naturally occurring microbiota. The best manufacturing process would be obtained with a longer salting time and the addition of the olive oil and paprika covering. Copyright © 2014 Elsevier Ltd. All rights reserved.

Enhancement of biodegradation of crude petroleum-oil in contaminated water by the addition of nitrogen sources.

Science.gov (United States)

Mukred, A M; Hamid, A A; Hamzah, A; Yusoff, W M Wan

2008-09-01

Addition of nitrogen sources as supplementary nutrient into MSM medium to enhance biodegradation by stimulating the growth four isolates, Acinetobacter faecalis, Staphylococcus sp., Pseudomonas putida and Neisseria elongata isolated from petroleum contaminated groundwater, wastewater aeration pond and biopond at the oil refinery Terengganu Malaysia was investigated. The organic nitrogen sources tested not only supported growth but also enhances biodegradation of 1% Tapis crude oil. All four isolates showed good growth especially when peptone was employed as the organic nitrogen compared to growth in the basal medium. Gas chromatography showed that more then 91, 93, 94 and 95% degradation of total hydrocarbon was observed after 5 days of incubation by isolates Pseudomonas putida, Neisseria elongate, Acinetobacter faecalis and Staphylococcus sp., respectively.

Batako Quality Optimization with Addition of Palm Oil Stem Fiber from Kampar District and Dumai City

Science.gov (United States)

Zainuri; Yanti, Gusneli; Wahyuni Megasari, Shanti

2017-12-01

The waste of dry palm oil produced by 148 trees per hectare is 3,108 ton/month or 37,296 ton/year as calculated. Riau province has oil palm plantations covering an area of 2.399.172 hectares (BPS Riau Province, 2014). It can be estimated the amount of waste generated. Palm stem waste can be utilized, one of which is the utilization of midrib fiber as an added material in the manufacture of batako. Batako- fiber that is made still must be examined feasibility as building materials. The purpose of this study was to determine the optimization of the quality of batako works by the addition of palm stem fiber originated from the districts of Kampar and Dumai. This research used experimental method with laboratory research. Batako-fiber with the addition of palm fiber stem 1% of the weight of cement can increase the value of compressive strength above the normal batako and a batako with first quality according to SNI 03-0349-1989 standard. The use of palm stem fiber originating from the Kampar district resulted in better batakos with higher average compressive strength values than the dumai-derived fibers, especially in the addition of 1% fiber by weight of cement. The finding of this research is that the batakos originating from Kampar district are better than those from Dumai city. The most optimal addition of palm fiber burrs to batako-fiber products is 1% of the weight of cement.

Effects of fish oil type, lipid antioxidants and presence of rapeseed oil on oxidative flavour stability of fish oil enriched milk

DEFF Research Database (Denmark)

Bruni Let, Mette; Jacobsen, Charlotte; Meyer, Anne S.

2004-01-01

As a part of our ongoing experiments on optimization of the oxidative stability of fish oils in genuine food systems, this study investigated the oxidative deterioration of fish oil enriched milk emulsions during cold storage. The experimental data showed that addition of rapeseed oil to fish oil...... (1:1) prior to emulsification into milk significantly protected the emulsions against oxidative deterioration. Addition of propyl gallate and a citric acid ester to the fish oil prior to emulsification also protected the fish oil enriched milk during storage. Emulsions containing a rapeseed:fish oil...... mixture were oxidatively stable during 11 d at 2 øC. Thus, no additional inhibitory effect of the added antioxidants was observed. The peroxide value and concentrations of five selected volatiles derived from n- 3 PUFA degradation in rapeseed:fish oil mixture emulsions were not significantly different...

Preparation and research on properties of castor oil as a diesel fuel additive

OpenAIRE

Nurbakhit Imankulov

2012-01-01

The research shows an opportunity of preparing biodiesel fuel on the basis of local diesel fuel and the bioadditive - castor oil. Limiting optimum concentration of introduction of the bioadditive equal was established as 5% mass ratio. The castor oil released from seeds of Palma Christi grown on experimental field. All physical and chemical characteristics of the oil including IR-spectra were determined. Operating conditions of castor oil introduction (temperature, solubility, concentra-tion,...

Green bio-oil extraction for oil crops

Science.gov (United States)

Zainab, H.; Nurfatirah, N.; Norfaezah, A.; Othman, H.

2016-06-01

The move towards a green bio-oil extraction technique is highlighted in this paper. The commonly practised organic solvent oil extraction technique could be replaced with a modified microwave extraction. Jatropha seeds (Jatropha curcas) were used to extract bio-oil. Clean samples were heated in an oven at 110 ° C for 24 hours to remove moisture content and ground to obtain particle size smaller than 500μm. Extraction was carried out at different extraction times 15 min, 30 min, 45 min, 60 min and 120 min to determine oil yield. The biooil yield obtained from microwave assisted extraction system at 90 minutes was 36% while that from soxhlet extraction for 6 hours was 42%. Bio-oil extracted using the microwave assisted extraction (MAE) system could enhance yield of bio-oil compared to soxhlet extraction. The MAE extraction system is rapid using only water as solvent which is a nonhazardous, environment-friendly technique compared to soxhlet extraction (SE) method using hexane as solvent. Thus, this is a green technique of bio-oil extraction using only water as extractant. Bio-oil extraction from the pyrolysis of empty fruit bunch (EFB), a biomass waste from oil palm crop, was enhanced using a biocatalyst derived from seashell waste. Oil yield for non-catalytic extraction was 43.8% while addition of seashell based biocatalyst was 44.6%. Oil yield for non-catalytic extraction was 43.8% while with addition of seashell-based biocatalyst was 44.6%. The pH of bio-oil increased from 3.5 to 4.3. The viscosity of bio-oil obtained by catalytic means increased from 20.5 to 37.8 cP. A rapid and environment friendly extraction technique is preferable to enhance bio-oil yield. The microwave assisted approach is a green, rapid and environmental friendly extraction technique for the production of bio-oil bearing crops.

Synthesis of polymeric additives based on itaconic acid and their evaluation as pour point depressants for lube oil in relation to rheological flow properties

Directory of Open Access Journals (Sweden)

A.M. Al-Sabagh

2012-06-01

Full Text Available Modification of the wax crystal habit practical interest during transportation processing of lube oil at low temperature. Various pour point depressant (PPD additives can facilitate this modification by different mechanisms. Comb shaped polymer additives are known to depress the pour point of lube oil by providing different nucleation sites for the precipitation of wax. This paper describes performance based design, synthesis, characterization and evaluation of comb shaped polymeric additives. Alkyl itaconates were prepared by the esterification of itaconic acid with different saturated alcohols C16/C18/NAFOL 20+A (Cav = 20/NAFOL 1822 B (Cav = 22. The four synthesized monomers were characterized and copolymerized with styrene in different molar ratios. All the products were characterized by infra-red (FTIR, Nuclear Magnetic Resonance (NMR Spectroscopy and Gel permeation chromatography (GPC. Rheological properties of lube oil (with and without additives were studied by Brookfield viscometer. In this study the additives based on itaconic acid were evaluated as good PPD and rheology modifiers.

Heat-transfer, inside of the ground heat-transfer units, from liquid, additionally cooling the oil-immersed transformer

Directory of Open Access Journals (Sweden)

Madyshev Ilnur

2017-01-01

Full Text Available A device for cooling the oil-immersed transformer by means of thermoelectric transducers has been developed. Their operating principle is based on the fact that at night at minimum ambient temperature, the cold is accumulated inside of a vessel due to formation of water ice layer on the developed surfaces of thermoelectric transducers` ribs. Melting of this layer is used in the hottest time of a day for additional cooling of transformer oil in the cooling system of the transformer. Pre-cooling of the circulating water takes place in vertical ground heat-transfer units (VGHT units, mounted into ground drilled boreholes. Certain estimate calculations of the heat-transfer process have been carried out.

Enhancing biochar yield by co-pyrolysis of bio-oil with biomass: impacts of potassium hydroxide addition and air pretreatment prior to co-pyrolysis.

Science.gov (United States)

Veksha, Andrei; Zaman, Waheed; Layzell, David B; Hill, Josephine M

2014-11-01

The influence of KOH addition and air pretreatment on co-pyrolysis (600 °C) of a mixture of bio-oil and biomass (aspen wood) was investigated with the goal of increasing biochar yield. The bio-oil was produced as a byproduct of the pyrolysis of biomass and recycled in subsequent runs. Co-pyrolysis of the biomass with the recycled bio-oil resulted in a 16% mass increase in produced biochar. The yields were further increased by either air pretreatment or KOH addition prior to co-pyrolysis. Air pretreatment at 220 °C for 3 h resulted in the highest mass increase (32%) compared to the base case of pyrolysis of biomass only. No synergistic benefit was observed by combining KOH addition with air pretreatment. In fact, KOH catalyzed reactions that increased the bed temperature resulting in carbon loss via formation of CO and CO2. Copyright © 2014 Elsevier Ltd. All rights reserved.

Physical, chemical and sensory properties of brownies substituted with sweet potato flour (Ipomoea batatas L.) with addition of black cumin oil (Nigella sativa L.)

Science.gov (United States)

Ligarnasari, I. P.; Anam, C.; Sanjaya, A. P.

2018-01-01

Effect of addition black cumin oil on the physical (hardness) characteristics, chemical (water, ash, fat, protein, carbohydrate, antioxidant IC50, total phenol and active component) characteristics and sensory (flavor, taste, texture, overall) characteristics of brownies substituted sweet potato flour were investigated. Substituted brownies was added with 0.05%, 0.10%, 0.15%, 0.20% and 0.25% of nigella sativa oil. The result showed that water content, ash, protein, fat, total phenol were increased and carbohydrate, antioxidant IC50 was decreased by the addition of nigella sativa oil. Due to the sensory characteristics, panelist gave the high score for substituted brownies which was added 0.05% nigella sativa oil. The result showed that the best formula of substituted brownies which was added 0.05% of nigella sativa oil had 24.89% water content, 1.19% ash content, 7.54% protein content, 37.79% fat content, 53.06% carbohydrate contain, 1043.6 ppm IC50 antioxidant and 0.22% total phenol. The active component on the brownies using GCMS identification were palmitic acid, oleic acid, lauric acid, theobromine and vitamin E.

Effect of liquid oil additive on lithium-ion battery ceramic composite separator prepared with an aqueous coating solution

Energy Technology Data Exchange (ETDEWEB)

Kim, Sang Woo [Division of Advanced Materials Engineering, Kongju National University, 1223–24, Cheonan-daero, Cheonan, Chungnam, 31080 (Korea, Republic of); Ryou, Myung-Hyun [Department of Chemical & Biological Engineering, Hanbat National University, 125, Dongseodaero, Yuseong-gu, Daejeon, 34158 (Korea, Republic of); Lee, Yong Min, E-mail: yongmin.lee@hanbat.ac.kr [Department of Chemical & Biological Engineering, Hanbat National University, 125, Dongseodaero, Yuseong-gu, Daejeon, 34158 (Korea, Republic of); Cho, Kuk Young, E-mail: kycho@hanyang.ac.kr [Department of Materials Science and Chemical Engineering, Hanyang University, 55, Hanyangdaehak-ro, Sangrok-gu, Ansan, Gyeonggi-do, 15588 (Korea, Republic of)

2016-08-05

Ceramic composite separators (CCSs) play a critical role in ensuring safety for lithium-ion batteries (LIBs), especially for mid- and large-sized devices. However, production of CCSs using organic solvents has some cost and environmental concerns. An aqueous process for fabricating CCSs is attractive because of its cost-effectiveness and environmental-friendliness because organic solvents are not used. The success of an aqueous coating system for LIBs is dependent upon minimizing moisture content, as moisture has a negatively impact on LIB performance. In this study, CCSs were fabricated using an aqueous coating solution containing Al{sub 2}O{sub 3} and an acrylic binder. Compared with polyethylene (PE) separators, CCSs coated with an aqueous coating solution showed improved thermal stability, electrolyte uptake, puncture strength, ionic conductivity, and rate capability. In addition, our new approach of introducing a small amount of an oily liquid to the aqueous coating solution reduced the water adsorption by 11.7% compared with coatings that do not contain the oily liquid additive. - Highlights: • Ceramic composite separator is fabricated using aqueous coating process. • Coated separator showed enhanced mechanical and thermal stability. • Liquid oil additive in coating solution reduce moisture reabsorption of separator. • Oil additive in aqueous coating solution does not deteriorate LIB performance.

Evaluation of the crude oil viscosity variation in function of the demulsifiers addition; Avaliacao da variacao da viscosidade de oleo cru em funcao da adicao de desemulsificante

Energy Technology Data Exchange (ETDEWEB)

Lopes, Jansen M.; Lucas, Elisabete F. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Inst. de Macromoleculas]. E-mail: elucas@ima.ufrj.br; Neves, Guilherme B.M. [COMAB Especialidades Quimicas Ltda., Rio de Janeiro, RJ (Brazil)]. E-mail: tecnico@comabrio.com

2003-07-01

One way of improving well production is the addition of demulsifier already in the gas lift. This is due to the apparent viscosity of water-in-oil emulsions being higher than apparent viscosity of crude oil, which in turn is higher than the apparent viscosity of an water-in-oil dual phase admixture and is also higher than the apparent viscosity of an oil-in-water emulsion. However, there are some situations where, in order to obtain separate flows of oil and water phases, demulsifier should be added in specific amounts in order to promote the desired phase separation. In heavy oils water and oil phase separation may be hard to obtain, however, the right demulsifier amount may imply in a considerable decrease in petroleum viscosity even without the appearance of two phases, making the flow easier. This work has evaluated the viscosity of a heavy crude having API degree 14 and BSW 52%, as a function of the addition of different amounts of DEMTROL BR 67, manufactured by Dow Quimica/Comab, Brazil, as demulsifier. (author)

Destabilization emulsion of oil by means of additives based on silicones polyethers; Desestabilizacao de emulsoes de petroleo por meio de aditivos a base de silicones polieteres

Energy Technology Data Exchange (ETDEWEB)

Jarque, Erika A.; Mansur, Claudia R.E. [Universidade Federal do Rio de Janeiro (IMA/UFRJ), RJ (Brazil). Inst. de Macromoleculas Professora Eloisa Mano], e-mails: alegrio@ima.ufrj.br, celias@ima.ufrj.br

2011-07-01

The process of demulsification has great importance in the petroleum industry, since the formation of emulsions is a natural phenomenon in this sector. Several polymers have been used commercially as additives emulsion destabilizing, among them are the block copolymers of poly (ethylene oxide)-poly (propylene oxide) (PEO-PPO). This work aims to study the efficiency of five additives based on silicones polyethers, which have structures in their chains of poly (ethylene oxide) (PEO) or PEO-PPO copolymers. The results show that the addition of these additives in the water / oil reduced the values of interfacial tension of systems. From the testing of gravitational separation water / oil was observed that all the additives promoted the breakdown of water / oil, but those who hold in their structures the chains of block copolymers of PEO-PPO were the most efficient, and that the caused a smaller reduction in the interfacial tensions of these systems. (author)

Effects of an Addition of Different Essential Oils and Their Combinations to Diets on Performance and Carcass Characteristics Parameters in Broilers

Directory of Open Access Journals (Sweden)

Behlül Sevim

2017-08-01

Full Text Available This study was conducted to determine the effect of dietary supplementation of thymus (Thymus vulgaris L., rosemary (Rosmarinus officinalis L. and French lavender (Lavandua stoechas L. essential oils and their mixtures on body weight and body weight gain, feed consumption, feed conversion ratio, carcass characteristics in broiler. A total of one day old 640 broiler chicks (Ross 308 were used divided into 8 groups each having five replicates, ramdomly. There were 80 chicks in each experimental group. The experimental diets were consisted of control (0 mg/kg, addition to thymus essential oil (50 mg/kg, rosemary essential oil (50 mg/kg, lavandula essential oil (50 mg/kg tymus + rosemary (25+25 mg/kg, tymus + lavandula (25+25 mg/kg, rosemary + lavandula (25+25 mg/kg, tymus + rosemary + lavandula (16.7+16.7+16.7 mg/kg, respectively. Feed and water were provided as ad libitum. Experimental period was six weeks. The according to results that dietary different essential oil and their combinations did not significantly effect on body weight, body weight gain, feed consumption, feed conversion ratio and carcass characteristics.

Experimental Evaluation of Oxide Nanoparticles as Friction and Wear Improvement Additives in Motor Oil

Directory of Open Access Journals (Sweden)

Nicholaos G. Demas

2017-01-01

Full Text Available The effect of two nanoparticle oxides on friction and wear was studied under laboratory test conditions using a reciprocating test machine and two test configurations. The addition of these nanoparticles in base stock oil under certain conditions reduced the coefficient of friction and improved wear, but that depended on the test configuration. Examination of the rubbed surfaces showed the pronounced formation of a tribofilm in some cases, while polishing on the surface was also observed in other cases. Contact configuration is important when oxide nanoparticles are being evaluated and the conclusions about their efficacy can be vastly different.

Effect of mode of addition of flaxseed oil on the quality characteristics of chicken sausage containing vitamin E and omega 3 fatty acids at levels to support a health claim.

Science.gov (United States)

Bolger, Zara; Brunton, Nigel P; Monahan, Frank J

2017-10-18

Vitamin E and omega-3 fatty acids can be incorporated into meat products at levels supporting health claims of "protecting against oxidative stress" and "maintaining normal blood cholesterol levels", respectively. Chicken sausages were formulated to contain vitamin E (12 mg per 100 g) and flaxseed oil (2 g per 100 g) using different oil incorporation methods. The formulations were: (1) control (no oil); (2) oil; (3) emulsified oil; (4) freeze-dried encapsulated oil; (5) freeze-dried encapsulated oil with cross-linker genipin; (6) spray-dried encapsulated oil. α-Linolenic acid and α-tocopherol were retained in all fortified formulations at levels to meet nutrient and health claims but emulsification or encapsulation had no additional benefit in retention following cooking or on product quality as measured by proximate composition, lipid oxidation, colour, microbial analysis, cook loss and texture profile analysis. While the addition of flaxseed oil had a negative effect on consumer acceptance of flavour (although not when emulsified), overall acceptance of the chicken sausages was only reduced significantly (p ≤ 0.05) when oil was encapsulated.

Transesterification of babassu oil catalyzed by Burkholderia cepacia encapsulated in sol-gel matrix employing protic ionic liquid as an additive

Directory of Open Access Journals (Sweden)

Maria Vanessa Souza Oliveira

2014-02-01

Full Text Available Enzymatic transesterification from non-edible vegetable oil (babassu oil and ethanol is provided. A set of seven experiments featuring a full 22 factorial design with three central points and different combinations of molar ratio and temperature as independent variables was employed. Transesterification reactions were catalyzed by Burkholderia cepacia lipase encapsulated in a hydrophobic matrix obtained by the sol-gel technique using protic ionic liquid (N-methylmonoethanolamine pentanoate as additive and with conventional heating (40 – 56°C. Ethyl esters highest yield (51.90% was obtained by experimental design with 1:7 molar ratio (oil:alcohol and temperature at 40°C during 48h reaction. The process with a 5-fold increase of enzymatic load provided 98.69% ethyl esters yield with 4.29 mm2 s-1 viscosity

Ionic Liquids as Novel Lubricants and /or Lubricant Additives

Energy Technology Data Exchange (ETDEWEB)

Qu, J. [ORNL; Viola, M. B. [General Motors Company

2013-10-31

This ORNL-GM CRADA developed ionic liquids (ILs) as novel lubricants or oil additives for engine lubrication. A new group of oil-miscible ILs have been designed and synthesized with high thermal stability, non-corrosiveness, excellent wettability, and most importantly effective anti-scuffing/anti-wear and friction reduction characteristics. Mechanistic analysis attributes the superior lubricating performance of IL additives to their physical and chemical interactions with metallic surfaces. Working with a leading lubricant formulation company, the team has successfully developed a prototype low-viscosity engine oil using a phosphonium-phosphate IL as an anti-wear additive. Tribological bench tests of the IL-additized formulated oil showed 20-33% lower friction in mixed and elastohydrodynamic lubrication and 38-92% lower wear in boundary lubrication when compared with commercial Mobil 1 and Mobil Clean 5W-30 engine oils. High-temperature, high load (HTHL) full-size engine tests confirmed the excellent anti-wear performance for the IL-additized engine oil. Sequence VID engine dynamometer tests demonstrated an improved fuel economy by >2% for this IL-additized engine oil benchmarked against the Mobil 1 5W-30 oil. In addition, accelerated catalyst aging tests suggest that the IL additive may potentially have less adverse impact on three-way catalysts compared to the conventional ZDDP. Follow-on research is needed for further development and optimization of IL chemistry and oil formulation to fully meet ILSAC GF-5 specifications and further enhance the automotive engine efficiency and durability.

Essential oil and aromatic plants as feed additives in non-ruminant nutrition: a review.

Science.gov (United States)

Zeng, Zhaikai; Zhang, Sai; Wang, Hongliang; Piao, Xiangshu

2015-01-01

This paper summarizes the current knowledge regarding the possible modes of action and nutritional factors involved in the use of essential oils (EOs) for swine and poultry. EOs have recently attracted increased interest as feed additives to be fed to swine and poultry, possibly replacing the use of antibiotic growth promoters which have been prohibited in the European Union since 2006. In general, EOs enhance the production of digestive secretions and nutrient absorption, reduce pathogenic stress in the gut, exert antioxidant properties and reinforce the animal's immune status, which help to explain the enhanced performance observed in swine and poultry. However, the mechanisms involved in causing this growth promotion are far from being elucidated, since data on the complex gut ecosystem, gut function, in vivo oxidative status and immune system are still lacking. In addition, limited information is available regarding the interaction between EOs and feed ingredients or other feed additives (especially pro- or prebiotics and organic acids). This knowledge may help feed formulators to better utilize EOs when they formulate diets for poultry and swine.

Improved tribological properties of the synthesized copper/carbon nanotube nanocomposites for rapeseed oil-based additives

Science.gov (United States)

Wang, Zhiqiang; Ren, Ruirui; Song, Haojie; Jia, Xiaohua

2018-01-01

Carbon nanotubes (CNTs) decorated with uniform copper nanoparticles (Cu NPs) were successfully prepared via a facile approach towards surface modification of CNTs with spontaneous polydopamine (PDA). The structures and morphologies of the nanocomposites were investigated by different kinds of techniques, including X-ray diffraction (XRD), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). Cu/PDA/CNTs nanocomposites were fabricated by growing the Cu NPs with an average diameter of 5 nm on the surfaces of PDA-modified CNTs. The CNTs functionalized with PDA layer not only provide an anchoring platform for the Cu NPs immobilization, but also endow Cu/PDA/CNTs with good dispersion stability when Cu/PDA/CNTs nanocomposites were used as lubricant additive. The tribological performance of the nanocomposites as the rapeseed oil lubricant additive, as well as Cu NPs, CNTs, and Cu/CNTs, was also investigated using a MS-T3000 ball-on-disk tribometer. Results show that the 0.2 wt% Cu/PDA/CNTs nanoadditive simultaneously reduce the friction and wear by 33.5% and 23.7%, respectively, outperformed the tribological performance of Cu NPs, CNTs, and Cu/CNTs nanoadditives. In addition, the presence of active sites in Cu/PDA/CNTs was beneficial to reduce the time of running-in period, give rise to the fastest speed to be stable of the friction coefficient curve as compared to the other nanoadditives. X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy of the worn surfaces lubricated by the soybean oil with Cu/PDA/CNTs nanocomposites showed that formation of low shear strength tribofilms containing Cu/PDA/CNTs nanocomposites and its self-lubricating property was key factor in reduction of the friction and protection against wear and deformation.

Transformation of oil palm fronds into pentose sugars using copper (II) sulfate pentahydrate with the assistance of chemical additive.

Science.gov (United States)

Loow, Yu-Loong; Wu, Ta Yeong

2018-06-15

Among the chemical pretreatments available for pretreating biomass, the inorganic salt is considered to be a relatively new but simple reagent that offers comparable pentose (C5) sugar recoveries as the conventional dilute acid hydrolysis. This study investigated the effects of different concentrations (1.5-6.0% (v/v)) of H 2 O 2 or Na 2 S 2 O 8 in facilitating CuSO 4 ·5H 2 O pretreatment for improving pentose sugar recovery from oil palm fronds. The best result was observed when 0.2 mol/L of CuSO 4 ·5H 2 O was integrated with 4.5% (v/v) of Na 2 S 2 O 8 to recover 8.2 and 0.9 g/L of monomeric xylose and arabinose, respectively in the liquid fraction. On the other hand, an addition of 1.5% (v/v) of H 2 O 2 yielded approximately 74% lesser total pentose sugars as compared to using 4.5% (v/v) Na 2 S 2 O 8 . By using CuSO 4 ·5H 2 O alone (control), only 0.8 and 1.0 g/L xylose and arabinose, respectively could be achieved. The results mirrored the importance of using chemical additives together with the inorganic salt pretreatment of oil palm fronds. Thus, an addition of 4.5% (v/v) of Na 2 S 2 O 8 during CuSO 4 ·5H 2 O pretreatment of oil palm fronds at 120 °C and 30 min was able to attain a total pentose sugar yield up to ∼40%. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Lubrication Ability of Ionic Liquids as Additives for Wind Turbine Gearboxes Oils

Directory of Open Access Journals (Sweden)

Miguel A. Gutierrez

2016-05-01

Full Text Available The amount of energy that can be gained from the wind is unlimited, unlike current energy sources such as fossil and coal. While there is an important push in the use of wind energy, gears and bearing components of the turbines often fail due to contact fatigue, causing costly repairs and downtime. The objective of this work is to investigate the potential tribological benefits of two phosphonium-based ionic liquids (ILs as additives to a synthetic lubricant without additives and to a fully formulated and commercially available wind turbine oil. In this work, AISI 52100 steel disks were tested in a ball-on-flat reciprocating tribometer against AISI 440C steel balls. Surface finish also affects the tribological properties of gear surfaces. In order to understand the combined effect of using the ILs with surface finish, two surface finishes were also used in this study. Adding ILs to the commercial available or synthetic lubricant reduced the wear scar diameter for both surface finishes. This decrease was particularly important for trihexyltetradecylphosphonium bis(trifluoromethylsulfonyl amide, where a wear reduction of the steel disk around 20% and 23% is reached when 5 wt % of this IL is added to the commercially available lubricant and to the synthetic lubricant without additives, respectively.

Sunflower Oil but Not Fish Oil Resembles Positive Effects of Virgin Olive Oil on Aged Pancreas after Life-Long Coenzyme Q Addition

Science.gov (United States)

González-Alonso, Adrián; Ramírez-Tortosa, César L.; Varela-López, Alfonso; Roche, Enrique; Arribas, María I.; Ramírez-Tortosa, M. Carmen; Giampieri, Francesca; Ochoa, Julio J.; Quiles, José L.

2015-01-01

An adequate pancreatic structure is necessary for optimal organ function. Structural changes are critical in the development of age-related pancreatic disorders. In this context, it has been reported that different pancreatic compartments from rats were affected according to the fat composition consumed. Since there is a close relationship between mitochondria, oxidative stress and aging, an experimental approach has been developed to gain more insight into this process in the pancreas. A low dosage of coenzyme Q was administered life-long in rats in order to try to prevent pancreatic aging-related alterations associated to some dietary fat sources. According to that, three groups of rats were fed normocaloric diets containing Coenzyme Q (CoQ) for two years, where virgin olive, sunflower, or fish oil was included as unique fat source. Pancreatic samples for microscopy and blood samples were collected at the moment of euthanasia. The main finding is that CoQ supplementation gives different results according to fat used in diet. When sunflower oil was the main fat in the diet, CoQ supplementation seems to improve endocrine pancreas structure and in particular β-cell mass resembling positive effects of virgin olive oil. Conversely, CoQ intake does not seem to improve the structural alterations of exocrine compartment previously observed in fish oil fed rats. Therefore CoQ may improve pancreatic alterations associated to the chronic intake of some dietary fat sources. PMID:26426013

Sunflower Oil but Not Fish Oil Resembles Positive Effects of Virgin Olive Oil on Aged Pancreas after Life-Long Coenzyme Q Addition

Directory of Open Access Journals (Sweden)

Adrián González-Alonso

2015-09-01

Full Text Available An adequate pancreatic structure is necessary for optimal organ function. Structural changes are critical in the development of age-related pancreatic disorders. In this context, it has been reported that different pancreatic compartments from rats were affected according to the fat composition consumed. Since there is a close relationship between mitochondria, oxidative stress and aging, an experimental approach has been developed to gain more insight into this process in the pancreas. A low dosage of coenzyme Q was administered life-long in rats in order to try to prevent pancreatic aging-related alterations associated to some dietary fat sources. According to that, three groups of rats were fed normocaloric diets containing Coenzyme Q (CoQ for two years, where virgin olive, sunflower, or fish oil was included as unique fat source. Pancreatic samples for microscopy and blood samples were collected at the moment of euthanasia. The main finding is that CoQ supplementation gives different results according to fat used in diet. When sunflower oil was the main fat in the diet, CoQ supplementation seems to improve endocrine pancreas structure and in particular β-cell mass resembling positive effects of virgin olive oil. Conversely, CoQ intake does not seem to improve the structural alterations of exocrine compartment previously observed in fish oil fed rats. Therefore CoQ may improve pancreatic alterations associated to the chronic intake of some dietary fat sources.

Oil-based paint poisoning

Science.gov (United States)

Paint - oil-based - poisoning ... Hydrocarbons are the primary poisonous ingredient in oil paints. Some oil paints have heavy metals such as lead, mercury, cobalt, and barium added as pigment. These heavy metals can cause additional ...

Effect Of Additive Solar Oil On High Temperature Corrosion Resistance Of Diesel Machines

International Nuclear Information System (INIS)

Dani, Mohammad; H, Bagyo; Minsyahril, B.

2004-01-01

It has been done the study of thermal gravimetric analyse (TGA) accompanied with magnetic suspension balance (MSB) on the diesel machine of sample A (HV = 256.78 kgf/mm 2 , ρ = 6.65-7.16 g/cm 3 ) and sample B (HV 166.67 kgf/mm 2 , ρ= 5.39-5.57 g/cm 3 ). The samples were oxidized at 900 o C for 24 hours in the variation of with and without additives (Diesel Booster + Amylum Nitrate; DBANI and Diesel Booster;DB) in solar oil of 1: 1500. The samples were, then, characterized by X-Ray Diffraction (crystal structures) and Scanning Electron Microscope (microstructures). The result shows that the Fe 2 O 3 layers spread out over the sample surfaces and the oxidant grain boundaries are very compacted

Iranian-Oil-Free Zone and international oil prices

International Nuclear Information System (INIS)

Farzanegan, Mohammad Reza; Raeisian Parvari, Mozhgan

2014-01-01

One of the main elements of economic sanctions against Iran due to its nuclear and military programs is crude oil exportation restrictions in addition to investment in Iranian energy related projects. Senders of such sanction are interested in understanding the impacts of such embargos on international oil prices. We apply unrestricted vector autoregressive (VAR) model, using impulse response functions (IRF) and variance decomposition analysis (VDA) tools with annual data from 1965 to 2012 to analyze the dynamic response of international oil prices to Iranian oil export sanction. Controlling for the supply of non-Iranian oil, the world GDP per capita, and post-Islamic revolution exogenous dummy variables, we show that international oil prices respond negatively and statistically significant to increasing shock in absolute negative changes of the Iranian oil exports – our proxy of Iran oil sanctions – following the first 2 years after shock. The main reason is the positive response of the non-Iranian oil supply to negative shocks in Iranian oil exports, filling the missing supply of Iranian oil in international markets. - Highlights: • We analyze the interconnections between Iranian oil supply and global oil prices. • We use VAR modeling and annual data from 1965 to 2012 for the case of Iran. • There are no inflationary effects of Iranian oil sanction on world oil prices. • Non-Iranian oil supply offsets the missing Iranian oil in the market

Residual Sorption and leaching of the herbicide diuron following de-oiled two-phase olive mill waste addition to soil

Energy Technology Data Exchange (ETDEWEB)

Lopez-Pineiro, A.; Albarran, A.; Cabrera, D.; Rato, J. M.; Munoz, A.; Flores, S.

2009-07-01

The residual sorption, desorption, degradation, and leaching of the herbicide diuron (3-(3,4-dichlorophenyl)-1,1-dimethylurea) a herbicide widely used in olive groves, was studied following the addition to soils of de oiled two-phase olive mill waste (DTPOMW). Field experiments were conducted on an olive grove soil amended over seven years with DTPOMW. (Author)

Residual Sorption and leaching of the herbicide diuron following de-oiled two-phase olive mill waste addition to soil

International Nuclear Information System (INIS)

Lopez-Pineiro, A.; Albarran, A.; Cabrera, D.; Rato, J. M.; Munoz, A.; Flores, S.

2009-01-01

The residual sorption, desorption, degradation, and leaching of the herbicide diuron (3-(3,4-dichlorophenyl)-1,1-dimethylurea) a herbicide widely used in olive groves, was studied following the addition to soils of de oiled two-phase olive mill waste (DTPOMW). Field experiments were conducted on an olive grove soil amended over seven years with DTPOMW. (Author)

Effects on bread and oil quality after functionalization with microencapsulated chia oil.

Science.gov (United States)

González, Agustín; Martínez, Marcela L; León, Alberto E; Ribotta, Pablo D

2018-03-23

Omega-3 and omega-6 fatty acids-rich oils suffer oxidation reactions that alter their chemical and organoleptic quality. Microencapsulation can be a powerful tool for protection against ambient conditions. In the present study, the addition of microencapsulated chia oil as an ingredient in bread preparations and its effect on the technological and chemical quality of breads was investigated. Microencapsulation of chia oil was carried out by freeze-drying with soy proteins as wall material and oil release was determined under in vitro gastric and intestinal conditions. Encapsulated oil-containing bread showed no differences in specific volume, average cell area, firmness and chewiness with respect to control bread. Unencapsulated oil-containing bread showed a marked increase in hydroperoxide values respect to control, whereas encapsulated oil-containing bread values were not affected by baking and bread storage. The fatty acid profiles showed a decrease of 13% and 16%, respectively, in α-linolenic acid in the encapsulated and unencapsulated oils with respect to bulk chia oil. Sensory analysis showed no significant differences between bread samples. The addition of encapsulated chia oil did not alter the technological quality of breads and prevented the formation of hydroperoxide radicals. A ration of encapsulated oil-containing bread contributes 60% of the recommended dietary intake of omega-3 fatty acids. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Plant essential oils and allied volatile fractions as multifunctional additives in meat and fish-based food products: a review.

Science.gov (United States)

Patel, Seema

2015-01-01

Essential oils are concentrated aromatic volatile compounds derived from botanicals by distillation or mechanical pressing. They play multiple, crucial roles as antioxidants, food pathogen inhibitors, shelf-life enhancers, texture promoters, organoleptic agents and toxicity-reducing agents. For their versatility, they appear promising as food preservatives. Several research findings in recent times have validated their potential as functional ingredients in meat and fish processing. Among the assortment of bioactive compounds in the essential oils, p-cymene, thymol, eugenol, carvacrol, isothiocyanate, cinnamaldehyde, cuminaldehyde, linalool, 1,8-cineol, α-pinene, α-terpineol, γ-terpinene, citral and methyl chavicol are most familiar. These terpenes (monoterpenes and sesquiterpenes) and phenolics (alcohols, esters, aldehydes and ketones) have been extracted from culinary herbs such as oregano, rosemary, basil, coriander, cumin, cinnamon, mint, sage and lavender as well as from trees such as myrtle, fir and eucalyptus. This review presents essential oils as alternatives to conventional chemical additives. Their synergistic actions with modified air packaging, irradiation, edible films, bacteriocins and plant byproducts are discussed. The decisive roles of metabolic engineering, microwave technology and metabolomics in quality and quantity augmentation of essential oil are briefly mooted. The limitations encountered and strategies to overcome them have been illuminated to pave way for their enhanced popularisation. The literature has been mined from scientific databases such as Pubmed, Pubchem, Scopus and SciFinder.

Oxidative stability of pullulan nanofibers loaded with fish oil: effect of oil content and antioxidants addition

DEFF Research Database (Denmark)

García Moreno, Pedro Jesús; Damberg, C.; Stephansen, K.

Electrospinning processing is a promising technique for the encapsulation of thermolabile bioactive compounds (e.g. fish oil) since it does not require the use of heat. Furthermore, the nano-microfibers (NMF) obtained present a reduced size, which makes them easier to disperse in food matrices...... compared to traditional encapsulates (e.g. microcapsules produced by spray-drying). Biopolymers such as proteins and polysaccharides are required for the production of food-grade NMF. In this sense, pullulan, which is a food-approved polysaccharide, is an interesting encapsulating material due to its high...... electrospinnability and low oxygen permeability. In light of the above, the aim of this work was to investigate the oxidative stability of omega-3 enriched pullulan NMF. First, the influence of fish oil content (10-20-30 %) on the properties of the electrospinning solutions (e.g. viscosity, conductivity and surface...

Oil flow in deep waters: comparative study between light oils and heavy oils

Energy Technology Data Exchange (ETDEWEB)

Andreolli, Ivanilto [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2009-12-19

Ultra deeper waters fields are being exploited due to technological development. Under this scenario, the flow design is accomplished through pipelines subjected to low temperature and high pressure. Moreover, these flow lines are usually long causing a fast fluid cooling, which may affect flow assurance in some cases. Problems during topsides production plant's restart might occur if the oil is viscous and even in steady state a significant different behavior can be noticed, if compared to a less viscous oil. A comparison between light and heavy oil through a case study with the objective to show some heavy oil flow particularities is the purpose of this paper. Permanent and transient analyses for a specific geometry are presented. The results showed that thermal and proper viscosity modeling are required for heavy oil flow, differently from that of light oil flow, due to the exponential viscosity dependence to temperature and because the predominant laminar regime. In addition, on heavier and heavier oil flow systems, it is essential to consider exportation system's restart. (author)

Oil My Love

International Nuclear Information System (INIS)

Gay, Michel

2014-01-01

The author first describes how oil will disappear from non-producing countries, notably France and Europe and will therefore lead to an energy crisis. He outlines that renewable energies will have a weak contribution in the replacement of fossil energies (in this case, oil and gas). To illustrate these trends, the author proposes an appendix which presents and discusses the evolution of global consumption of fossil fuels, the evolution of production of different oil grades, a forecast of global oil demand by 2035, evolutions of productions and exports. Another appendix discusses additional issues on oil: the meaning of reserves, solutions for France in case of shortage of oil, the world oil situation (USA, China, Russia, the European Union, Japan)

Jatropha Oil Derived Sophorolipids: Production and Characterization as Laundry Detergent Additive

Directory of Open Access Journals (Sweden)

Kasturi Joshi-Navare

2013-01-01

Full Text Available Sophorolipids (SLs are glycolipidic biosurfactants suitable for various biological and physicochemical applications. The nonedible Jatropha oil has been checked as the alternative raw material for SL synthesis using C. bombicola (ATCC22214. This is useful towards lowering the SL production cost. Through optimization of fermentation parameters and use of resting cell method, the yield 15.25 g/L could be achieved for Jatropha oil derived SL (SLJO with 1% v/v oil feeding. The synthesized SL displayed good surfactant property. It reduced the surface tension of distilled water from 70.7 mN/m to 33.5 mN/m with the Critical Micelle Concentration (CMC value of 9.5 mg/L. Keeping the prospective use of the SL in mind, the physicochemical properties were checked along with emulsion stability under temperature, pH stress, and in hard water. Also antibacterial action and stain removal capability in comparison with commercial detergent was demonstrated. SLJO enhanced the detergent performance. Based on the results, it can be said that SLs have utility as fabric cleaner with advantageous properties such as skin friendly nature, antibacterial action, and biodegradability. Therefore SLs are potential green molecules to replace synthetic surfactants in detergents so as to reduce harm caused to environment through detergent usage.

Jatropha oil derived sophorolipids: production and characterization as laundry detergent additive.

Science.gov (United States)

Joshi-Navare, Kasturi; Khanvilkar, Poonam; Prabhune, Asmita

2013-01-01

Sophorolipids (SLs) are glycolipidic biosurfactants suitable for various biological and physicochemical applications. The nonedible Jatropha oil has been checked as the alternative raw material for SL synthesis using C. bombicola (ATCC22214). This is useful towards lowering the SL production cost. Through optimization of fermentation parameters and use of resting cell method, the yield 15.25 g/L could be achieved for Jatropha oil derived SL (SLJO) with 1% v/v oil feeding. The synthesized SL displayed good surfactant property. It reduced the surface tension of distilled water from 70.7 mN/m to 33.5 mN/m with the Critical Micelle Concentration (CMC) value of 9.5 mg/L. Keeping the prospective use of the SL in mind, the physicochemical properties were checked along with emulsion stability under temperature, pH stress, and in hard water. Also antibacterial action and stain removal capability in comparison with commercial detergent was demonstrated. SLJO enhanced the detergent performance. Based on the results, it can be said that SLs have utility as fabric cleaner with advantageous properties such as skin friendly nature, antibacterial action, and biodegradability. Therefore SLs are potential green molecules to replace synthetic surfactants in detergents so as to reduce harm caused to environment through detergent usage.

Effect in laboratory of addition of inorganic fertilizers made in degradation of hydrocarbon on contaminated soil by oil

International Nuclear Information System (INIS)

Pardo Castro, Jenny Liliana; Perdomo Rojas, Maria Carolina; Benavides Lopez de Mesa, Joaquin L

2004-01-01

At present one of the most important environmental problems is contamination of soil ecosystem by hydrocarbon spilling mainly of oil and its derivates, which occurs when oil is explored or transported. Furthermore in Colombia it occurs due to violent assaults made by men outside of law against petroleum infrastructure. To solve this problem there are treatment methods to recover contaminated soil as Land farming technique, adding organic nutrients. In this research this technique was evaluated in vitro, through a design of six experimental units (EU) which contained contaminated soil with crude oil; three EU were treated with Triple 15 inorganic fertilizer and the other three were taken as biotic control. Land farming effectiveness was determined by pH analysis, humidity percent, temperature, count of total heterotrophic microorganisms, and probable number of I degrades microorganisms, nutrients and total hydrocarbons for a four month experimental period At the d of that period, in Land farming treatment with nutrients added was achieved a high remotion percentage TPH up to 91 %, getting final TPH concentration of 2028 ppm comparing biotic control in which the remotion percentage achieved up to 65% and a TPH final concentration was 8049 ppm thus, it could demonstrate that nutrient addition optimizes the degrading hydrocarbon process in soil

Mitsubishi Oil to become a major oil player?

International Nuclear Information System (INIS)

Ash, N.

1994-01-01

Mitsubishi Oil became a wholly-owned Japanese company in 1984. Before that, since 1981, it had been a joint venture between Mitsubishi and Getty oil. Recently the company has discovered a major new oilfield off the coast of Vietnam. In addition it has a strategic stake in the Canadian Athabasca Far Sands, major investments in Angola and operations in Papua New Guinea and Gabon. It aims to cover 30 % of the crude oil imports to its four existing, and fifth projected, refineries from owned sources by the end of the century. Mitsubishi has a network of 4500 service stations in Japan and has become one of the largest lubricating oil producers. The company's main overseas sales are of jet fuel, lubricating and tanker oils, sulphur and some petrochemicals. (UK)

Oil markets to 2010: the impact of non-Opec oil

International Nuclear Information System (INIS)

Enav, Peter

1998-09-01

This report provides an in-depth assessment of oil development scenarios in every non-Opec oil producing country from 1998 to 2010, in addition to evaluating the extent and direction of future oil trade for Opec and non-Opec countries alike. It re-assesses world oil consumption patterns in light of the Asian financial crisis, providing a concise yet comprehensive coverage of an often-neglected oil production group. The oil market development scenario is analysed in each country, with detailed consideration of the major players providing historical production, consumption, import and export data; current oil balance - production, imports and exports; an assessment of oil development policy; analysis of potential development obstacles considering regulatory, financial, political and environmental issues; oil production and consumption projections to 2010, by type; and import and export projections to 2010, by destination and source. More than 80 tables supplying essential statistics on the world's non-Opec markets accompany the report, with maps and schematic diagrams showing existing and potential infrastructure and fields. (Author)

Improving Mechanical Properties of Thermoset Biocomposites by Fiber Coating or Organic Oil Addition

Directory of Open Access Journals (Sweden)

Truc T. Ngo

2015-01-01

Full Text Available Two different thermoset biocomposite systems are experimented in this study with the hope to improve their mechanical properties. Fiberglass and hemp, in form of fabrics, are used to reinforce the thermoset polymer matrix, which includes a traditional epoxy resin and a linseed oil-based bioresin (UVL. The fiber/polymer matrix interface is modified using two different approaches: adding a plant-based oil (pine or linseed to the polymer matrix or coating the fibers with 3-(aminopropyltriethoxysilane (APTES prior to integrating them into the polymer matrix. Epoxy resin is cured using an amine-based initiator, whereas UVL resin is cured under ultraviolet light. Results show that hemp fibers with APTES prime coat used in either epoxy or UVL matrix exhibit some potential improvements in the composite’s mechanical properties including tensile strength, modulus of elasticity, and ductility. It is also found that adding oil to the epoxy matrix reinforced with fiberglass mostly improves the material’s modulus of elasticity while maintaining its tensile strength and ductility. However, adding oil to the epoxy matrix reinforced with hemp doubles the material’s ductility while slightly reducing its tensile strength and modulus of elasticity.

21 CFR 172.876 - Castor oil.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Castor oil. 172.876 Section 172.876 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Multipurpose Additives § 172.876 Castor oil. The food additive castor oil may be safely used in accordance with...

Microbial diversity in oiled and un-oiled shoreline sediments in the Norwegian Arctic

International Nuclear Information System (INIS)

Grossman, M.J.; Prince, R.C.; Garrett, R.M.; Garrett, K.K.; Bare, R.E.; O'Neil, K.R.; Sowlay, M.R.; Hinton, S.M.; Lee, K.; Sergy, G.A.; Guenette, C.C.

2000-01-01

Field trials were conducted at an oiled shoreline on the island of Spitsbergen to examine the effect of nutrient addition on the metabolic status, potential for aromatic hydrocarbon degradation, and the phylogenetic diversity of the microbial community in oiled Arctic shoreline sediments. IF-30 intermediate fuel grade oil was applied to the shoreline which was then divided into four plots. One was left untreated and two were tilled. Four applications of fertilizer were applied over a two-month period. Phospholipid fatty acid (PLFA), gene probe and 16S microbial community analysis suggested that bioremediation stimulated the metabolic activity, increased microbial biomass and genetic potential for aromatic hydrocarbon degradation, and increased the population of hydrocarbon degradation of an oiled Arctic shoreline microbial community. The results of this study are in agreement with the results from stimulation of oil biodegradation in temperate marine environments. It was concluded that biodegradation and fertilizer addition are feasible treatment methods for oil spills in Arctic regions. 31 refs., 3 tabs., 3 figs

21 CFR 73.300 - Carrot oil.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Carrot oil. 73.300 Section 73.300 Food and Drugs... ADDITIVES EXEMPT FROM CERTIFICATION Foods § 73.300 Carrot oil. (a) Identity. (1) The color additive carrot oil is the liquid or the solid portion of the mixture or the mixture itself obtained by the hexane...

Treating oil shale

Energy Technology Data Exchange (ETDEWEB)

Dolbear, S H

1921-01-04

Oil shale is treated for the separation of the valuable organic compounds, with a view to economy in subsequent destructive distillation, by grinding to powder, mixing with water to form a pulp, adding a small quantity of an oil liquid and aerating the mixture to form a froth containing the organic compounds. If the powdered shale contains sufficient free oil, the addition of oil to the pulp may be dispensed with. In some cases an electrolyte such as sulfuric acid may be added to the pulp.

Effects of petroleum oil and soybean oil in adjuvants for postemergence herbicides

International Nuclear Information System (INIS)

Harrison, S.K.

1985-01-01

Soybean oil is an abundant and renewable resource through annual crop production. The replacement of paraffin oil with soybean oil in agricultural adjuvants would create an additional market for surplus soybeans and help alleviate dependence on non-renewable petroleum oil. Field and laboratory experiments were conducted to compare effects of a petroleum oil-emulsifier blend (POC) and a soybean oil-emulsifier blend (SBOC) as adjuvants for postemergence herbicides. In field experiments, little difference was observed between POC and SBOC in the ability to enhance control of velvetleaf (Abutilon theophrasti Medik.) with 0.6 or 1.1 kg/ha bentazon [3-(1-methylethyl)-(1H)-2,1,3-benzothiadiazin-4(3H)-one 2,2-dioxide]. Control of giant foxtail (Setaria faberi Herrm.) with 0.1 kg/ha sethoxydim {2-[1-(ethoxyimino)butyl]-5-[2-(ethylthio)propyl]-3-hydroxy-2-cyclohexen-1-one} was enhanced more by POC than by SBOC. The effects of adjuvants and relative humidity (RH) on absorption, translocation, and metabolism of the methyl ester of 14 C-haloxyfop {2-[4-[[3-chloro-5-(trifluoromethyl)-2-pyridinyl]oxy]phenoxy]propanoic acid} in corn (Zea mays L.) were investigated. Addition of 1.0% (v/v) POC to the treatment solution resulted in greater foliar absorption and translocation of 14 C than addition of 1.0% (v/v) SBOC

Vacuum pyrolysis of waste tires with basic additives

International Nuclear Information System (INIS)

Zhang Xinghua; Wang Tiejun; Ma Longlong; Chang Jie

2008-01-01

Granules of waste tires were pyrolyzed under vacuum (3.5-10 kPa) conditions, and the effects of temperature and basic additives (Na 2 CO 3 , NaOH) on the properties of pyrolysis were thoroughly investigated. It was obvious that with or without basic additives, pyrolysis oil yield increased gradually to a maximum and subsequently decreased with a temperature increase from 450 deg. C to 600 deg. C, irrespective of the addition of basic additives to the reactor. The addition of NaOH facilitated pyrolysis dramatically, as a maximal pyrolysis oil yield of about 48 wt% was achieved at 550 deg. C without the addition of basic additives, while a maximal pyrolysis oil yield of about 50 wt% was achieved at 480 deg. C by adding 3 wt% (w/w, powder/waste tire granules) of NaOH powder. The composition analysis of pyrolytic naphtha (i.b.p. (initial boiling point) ∼205 deg. C) distilled from pyrolysis oil showed that more dl-limonene was obtained with basic additives and the maximal content of dl-limonene in pyrolysis oil was 12.39 wt%, which is a valuable and widely-used fine chemical. However, no improvement in pyrolysis was observed with Na 2 CO 3 addition. Pyrolysis gas was mainly composed of H 2 , CO, CH 4 , CO 2 , C 2 H 4 and C 2 H 6 . Pyrolytic char had a surface area comparable to commercial carbon black, but its proportion of ash (above 11.5 wt%) was much higher

Effect of nitrate addition on the diversity and activity of sulfate-reducing prokaryotes in high-temperature oil production systems

DEFF Research Database (Denmark)

Gittel, Antje; Wieczorek, Adam; Sørensen, Ketil

Sulfate-reducing prokaryotes (SRP) producing hydrogen sulfide cause severe problems like microbial corrosion, souring and plugging in seawater-injected oil production systems. Adding nitrate to the injection water is a possible strategy to control the activity of SRP by favoring the growth of both...... heterotrophic, nitrate-reducing bacteria that outcompete SRP for substrates, and nitrate-reducing, sulfide-oxidizing bacteria (NR-SOB). To assess the effects of nitrate addition, microbial diversity (Bacteria, Archaea) and SRP activity were studied in the production waters of a nitrate-treated and a non...... their potential activity under pipeline (60°C), but not under oil reservoir conditions (80°C), indicating that the troublesome SRP were pipeline-derived. Consistent with the low amount of SRP, no activity could be shown for samples from the nitrate-treated system suggesting that SRP were inhibited by nitrate...

Process for separating and recovering oil from oil-sands, etc

Energy Technology Data Exchange (ETDEWEB)

Preller, H

1920-07-14

A process for separating and recovering oil from oil-sands, bitumen from oil-chalk, oil shale, and coal is characterized in that the material to be separated feeds, by a self-acting feeding arrangement, to a system with slowly rotating drums alternating in different directions and thereby it is exposed to the action of hot water running opposite to the rotation, direction of the drum, with addition of extraction-medium, so that the light material is washed out and rises to the top. It is carried off, while the heavy material sinks to the bottom and, by bucket-conveyor is removed.

Influence of Food Characteristics and Food Additives on the Antimicrobial Effect of Garlic and Oregano Essential Oils.

Science.gov (United States)

García-Díez, Juan; Alheiro, Joana; Pinto, Ana Luisa; Soares, Luciana; Falco, Virgilio; Fraqueza, Maria João; Patarata, Luis

2017-06-10

Utilization of essential oils (EOs) as antimicrobial agents against foodborne disease has gained importance, for their use as natural preservatives. Since potential interactions between EOs and food characteristics may affect their antimicrobial properties, the present work studies the influence of fat, protein, pH, a w and food additives on the antimicrobial effect of oregano and garlic EOs against Salmonella spp. and Listeria monocytogenes. Results showed that protein, pH, a w , presence of beef extract, sodium lactate and nitrates did not influence their antimicrobial effect. In contrast, the presence of pork fat had a negative effect against both EOs associated with their dilution of the lipid content. The addition of food phosphates also exerts a negative effect against EOs probably associated with their emulsification properties as observed with the addition of fat. The results may help the food industry to select more appropriate challenges to guarantee the food safety of foodstuffs.

Separation of oil and grease from oil sludge using surfactant

International Nuclear Information System (INIS)

Ainon Abdul Aziz; Syed Hakimi Sakuma Syed Ahmad; Zalina Laili

2005-01-01

The objective of the experiments was to observe the efficiency of the surfactant to remove oil and grease from oil sludges using various surfactant concentration ranging from 10 %, 15 %, 20 % and 30 %. The surfactant solution consists of two mixtures of Aqua 2000 and D Bond. The oil sludge were subjected to heating and surfactant treatment process. Remaining oil and grease concentration were observed on the oil sludges after treatment. Small scale experiments were conducted by heating process, without heating process and heating process with addition of sodium chloride. Surfactant solution was added in each process. Results shows that there is separation of oil and grease from the oil sludges. There were formation of mini emulsions (oil in water). The higher the concentration of surfactant used, the higher the concentrations of mini emulsion formed as observed. Solid remains after the treatment process were found to contain lesser oil concentration with presence of bitumen, sediment, organic and inorganic materials. After a washing process using distilled water, the solid was still black but less oily than before the treatment. There is no separation of oil occurred in aqueous solution for the control experiment. (Author)

Influence of the addition and storage time of crude extract of tea leaves (camellia sinensis l.) toward value of free fatty acid in crude palm oil

Science.gov (United States)

Erwin; Wahifiyah, E.; Hairani, R.; Panggabean, A. S.

2018-04-01

The purpose of this study was to determine the effect of the crude extract of tea leaves (Camellia sinensis L.) and storage time on the content of free fatty acid in palm oil. The dried tea leaves were macerated and concentrated by rotary evaporator. The extract obtained was added to crude palm oil with various added mass of the extract and various storage times. Phytochemical tests indicated the presence of secondary metabolites including alkaloids, triterpenoids, steroids, phenolics and flavonoids. The ANOVA test showed a decrease in free fatty acid content in crude palm oil with the addition of tea leaves extract. The LSD (Least Significant Difference) test showed the best influence on ALB of palm oil is on the total extract mass of 2 grams and the storage time of 20 days.

English-Chinese oil field dictionary. [English-Chinese

Energy Technology Data Exchange (ETDEWEB)

Gow, S [comp.

1979-01-01

In this edition the original English-Chinese Oil Field Dictionary was modified line by line and major additions and deletions were made. A total of 37,000 terms and phrases were collected. The following disciplines were included: petroleum geology, earth physics and detection, well prospecting and measuring, development of oil fields, oil recovery, oil storage and transport, etc. In addition, a limited number of common scientific terms, phrases and terminologies were also included.

Fractional distillation of oil

Energy Technology Data Exchange (ETDEWEB)

Jones, L D

1931-10-31

A method of dividing oil into lubricating oil fractions without substantial cracking by introducing the oil in a heated state into a fractionating column from which oil fractions having different boiling points are withdrawn at different levels, while reflux liquid is supplied to the top of the column, and additional heat is introduced into the column by contacting with the oil therein a heated fluid of higher monlecular weight than water and less susceptible to thermal decomposition than is the highest boiling oil fraction resulting from the distillation, or of which any products produced by thermal decomposition will not occur in the highest boiling distillate withdrawn from the column.

21 CFR 73.315 - Corn endosperm oil.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Corn endosperm oil. 73.315 Section 73.315 Food and... ADDITIVES EXEMPT FROM CERTIFICATION Foods § 73.315 Corn endosperm oil. (a) Identity. (1) The color additive corn endosperm oil is a reddish-brown liquid composed chiefly of glycerides, fatty acids, sitosterols...

Starch plus sunflower oil addition to the diet of dry dairy cows results in a trans-11 to trans-10 shift of biohydrogenation.

Science.gov (United States)

Zened, A; Enjalbert, F; Nicot, M C; Troegeler-Meynadier, A

2013-01-01

Trans fatty acids (FA), exhibit different biological properties. Among them, cis-9,trans-11 conjugated linoleic acid has some interesting putative health properties, whereas trans-10,cis-12 conjugated linoleic acid has negative effects on cow milk fat production and would negatively affect human health. In high-yielding dairy cows, a shift from trans-11 to trans-10 pathway of biohydrogenation (BH) can occur in the rumen of cows receiving high-concentrate diets, especially when the diet is supplemented with unsaturated fat sources. To study this shift, 4 rumen-fistulated nonlactating Holstein cows were assigned to a 4×4 Latin square design with 4 different diets during 4 periods. Cows received 12 kg of dry matter per day of 4 diets based on corn silage during 4 successive periods: a control diet (22% starch, diet supplemented with wheat plus barley (35% starch, diet supplemented with 5% of sunflower oil (20% starch, 7.6% crude fat), and a high-starch plus sunflower oil diet (33% starch, 7.3% crude fat). Five hours after feeding, proportions of trans-11 BH isomers greatly increased in the rumen content with the addition of sunflower oil, without change in ruminal pH compared with the control diet. Addition of starch to the control diet had no effect on BH pathways but decreased ruminal pH. The addition of a large amount of starch in association with sunflower oil increased trans-10 FA at the expense of trans-11 FA in the rumen content, revealing a trans-11 to trans-10 shift. Interestingly, with this latter diet, ruminal pH did not change compared with a single addition of starch. This trans-11 to trans-10 shift occurred progressively, after a decrease in the proportion of trans-11 FA in the rumen, suggesting that this shift could result from a dysbiosis in the rumen in favor of trans-10-producing bacteria at the expense of those producing trans-11 or a modification of bacterial activities. Copyright © 2013 American Dairy Science Association. Published by Elsevier

Do Oil-Producing Countries Have Normal Oil Overconsumption? An Investigation of Economic Growth and Energy Subsidies

OpenAIRE

Seyed Reza Mirnezami

2015-01-01

The data shows that oil-producing countries have low oil retail prices and low economic growth compared with other countries. Considering that oil-producing countries experience high oil consumption and low economic growth, it is possible to argue that economic growth is not an appropriate justification for oil consumption and that the main cause for high oil consumption is the low retail price. In addition, it should be noted that the global environmental movement against increasing greenhou...

The flotation of Roşia Poieni copper ore in column machine, with non-polar oils addition

Directory of Open Access Journals (Sweden)

Ciocani V.

2005-11-01

Full Text Available The most important natural resource of copper in Romania is the ore deposit of Roşia Poieni. At present, the utilization of Roşia Poieni poorphyry copper ore is possible by extraction in quarry of the mass ore and mineral processing into a technological flux with modest results for the value of metal recovery in concentrate 70-72 % and an average contents of 16,5 % Cu. Our researches were directed to studies regarding test and utilisation of special procedure of flotation – addition of the non-polar oil – applied to advanced grinding ore with column type machines.

Delay oil oxidation during frying process

International Nuclear Information System (INIS)

Atta, N.M.M.; Shams Eldin, N.M.M.

2010-01-01

Blend oil (mixed of refined sunflower and soy beans oils 1:1 w/w) containing add 200 ppm of rosemary leaves methanolic extract (rosemary extract) (RE) and 3% refined rice bran oil (RRBO), were used in frying process at 1800 degree c for 5 hrs/ day, four consecutive days to delay oil oxidation during frying. Therefore, rosemary extract (methanolic extract) was analyzed by HPLC technique for identification of flavonoids compounds (as a specific active compounds; gives high protection to frying oil). Physical and chemical properties, including refractive index(RI). Red color unit (R), viscosity, acidity (FFA), peroxide value (PV), iodine value (IV) oxidized fatty acid (OFA), polymer content (PC), total polar components (TPC) and trans fatty acid (TFA) as eliadic acid were determined. The results indicated that; rosemary extract contained about eight flavonoids compounds (hypersoid, rutin, 3-OH flavon, luleotin, kempferol, sakarutin, querectrin and apeginin). Addition of RE or RRBO to frying oil caused delay oil oxidation during frying process compared with frying oil without any addition. Also, the results indicated that rosemary extract was more effective in reducing formation of PV, FFA, OFA, PC, TPC and TFA in frying oil than refined rice bran oil

ORNL-GM: Development of Ionic Liquid-Additized, GF-5/6 Compatible Low-Viscosity Oils for Automotive Engine and Rear Axle Lubrication for 4% Improved Fuel Economy

Energy Technology Data Exchange (ETDEWEB)

Qu, Jun [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Zhou, Yan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Luo, Huimin [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Toops, Todd J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Brookshear, Daniel W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Stump, Benjamin C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Viola, Michael B. [General Motors (GM) Technical Center, Pontiac, MI (United States); Zreik, Khaled [General Motors (GM) Technical Center, Pontiac, MI (United States); Ahmed, Tasfia [General Motors (GM) Technical Center, Pontiac, MI (United States)

2017-01-01

The overall objective of this project are as follows: Further develop ionic liquid (IL)-additized lowviscosity engine oils meeting the GF-5/6 specifications and possessing superior lubricating characteristics; Expand the IL additive technology to rear axle lubricants; and Seek a combined improvement in the vehicle fuel economy

Do Oil-Producing Countries Have Normal Oil Overconsumption? An Investigation of Economic Growth and Energy Subsidies

Directory of Open Access Journals (Sweden)

Seyed Reza Mirnezami

2015-07-01

Full Text Available The data shows that oil-producing countries have low oil retail prices and low economic growth compared with other countries. Considering that oil-producing countries experience high oil consumption and low economic growth, it is possible to argue that economic growth is not an appropriate justification for oil consumption and that the main cause for high oil consumption is the low retail price. In addition, it should be noted that the global environmental movement against increasing greenhouse gas emissions—for example, the Kyoto 1998 agreement—seems to have had no effect on oil consumption in oil-producing countries.

Pore-Scale Investigation of Crude Oil/CO₂ Compositional Effects on Oil Recovery by Carbonated Water Injection

DEFF Research Database (Denmark)

Seyyedi, Mojtaba; Sohrabi, Mehran

2017-01-01

where the oil has significant dissolved gases. In such studies, oil swelling and oil viscosity reduction had been introduced as the main mechanisms of additional oil recovery by CWI. However, in our direct flow visualization (micro model) studies reported here, we have used live crude oil, and we have...

Effect of nitrate addition on prokaryotic diversity and the activity of sulfate-reducing prokaryotes in high-temperature oil production systems

DEFF Research Database (Denmark)

Gittel, Antje; Wieczorek, Adam; Sørensen, Ketil

Adding nitrate to injection water is a possible strategy to control the activity of sulfate-reducing prokaryotes (SRP) in oil production system. To assess the effects of nitrate addition, prokaryotic diversity (Bacteria, Archaea, SRP) and SRP activity were studied in the production waters......-treated site was additionally supported by demonstrating their potential activity at 58°C, indicating that the troublesome SRP were pipeline-derived. Consistent with the low frequency of SRP in the clone libraries, no activity could be shown for samples from the nitrate-treated system suggesting that SRP were...... inhibited by nitrate addition. Visualization and quantification of the identified troublesome prokaryotes and potential competitors using the CARD-FISH technique will be performed on production water from both sites....

RESEARCH OIL RECOVERY MECHANISMS IN HEAVY OIL RESERVOIRS

Energy Technology Data Exchange (ETDEWEB)

Anthony R. Kovscek; William E. Brigham

1999-06-01

The United States continues to rely heavily on petroleum fossil fuels as a primary energy source, while domestic reserves dwindle. However, so-called heavy oil (10 to 20{sup o}API) remains an underutilized resource of tremendous potential. Heavy oils are much more viscous than conventional oils. As a result, they are difficult to produce with conventional recovery methods such as pressure depletion and water injection. Thermal recovery is especially important for this class of reservoirs because adding heat, usually via steam injection, generally reduces oil viscosity dramatically. This improves displacement efficiency. The research described here was directed toward improved understanding of thermal and heavy-oil production mechanisms and is categorized into: (1) flow and rock properties; (2) in-situ combustion; (3) additives to improve mobility control; (4) reservoir definition; and (5) support services. The scope of activities extended over a three-year period. Significant work was accomplished in the area of flow properties of steam, water, and oil in consolidated and unconsolidated porous media, transport in fractured porous media, foam generation and flow in homogeneous and heterogeneous porous media, the effects of displacement pattern geometry and mobility ratio on oil recovery, and analytical representation of water influx. Significant results are described.

Biodiesel production using waste frying oil

International Nuclear Information System (INIS)

Charpe, Trupti W.; Rathod, Virendra K.

2011-01-01

Research highlights: → Waste sunflower frying oil is successfully converted to biodiesel using lipase as catalyst. → Various process parameters that affects the conversion of transesterification reaction such as temperature, enzyme concentration, methanol: oil ratio and solvent are optimized. → Inhibitory effect of methanol on lipase is reduced by adding methanol in three stages. → Polar solvents like n-hexane and n-heptane increases the conversion of tranesterification reaction. - Abstract: Waste sunflower frying oil is used in biodiesel production by transesterification using an enzyme as a catalyst in a batch reactor. Various microbial lipases have been used in transesterification reaction to select an optimum lipase. The effects of various parameters such as temperature, methanol:oil ratio, enzyme concentration and solvent on the conversion of methyl ester have been studied. The Pseudomonas fluorescens enzyme yielded the highest conversion. Using the P. fluorescens enzyme, the optimum conditions included a temperature of 45 deg. C, an enzyme concentration of 5% and a methanol:oil molar ratio 3:1. To avoid an inhibitory effect, the addition of methanol was performed in three stages. The conversion obtained after 24 h of reaction increased from 55.8% to 63.84% because of the stage-wise addition of methanol. The addition of a non-polar solvent result in a higher conversion compared to polar solvents. Transesterification of waste sunflower frying oil under the optimum conditions and single-stage methanol addition was compared to the refined sunflower oil.

Lipid oxidation in fish oil enriched oil-in-water emulsions and cream cheese with pre-emulsified fish oil is affected differently by the emulsifier used

DEFF Research Database (Denmark)

Horn, Anna Frisenfeldt; Nielsen, Nina Skall; Andersen, Ulf

It is well-documented that a high intake of long chain omega-3 polyunsaturated fatty acids has several health beneficial effects in humans. Consequently, the interest in food products enriched with marine oils has increased during recent years. However, addition of these highly unsaturated fatty...... will include results from studies on lipid oxidation in simple oil-in-water emulsions prepared with milk proteins alone or combinations of milk proteins and phospholipids. In addition, a study on fish oil enriched cream cheese will be presented. In this study, the cream cheese was enriched with either neat...... acids to foods invariably increases the risk of lipid oxidation. A possible strategy to avoid lipid oxidation and the consecutive development of unpleasant off-flavours is to protect the oil in a delivery emulsion in which the oil droplets are shielded from its possible pro-oxidative surroundings...

Turbine oil change - the smart way

International Nuclear Information System (INIS)

Ahlf, J.; Prenzel, H.; Ertelt, R.

2002-01-01

The Nuclear Plant Unterweser (KKU) was commissioned in 1978. The gross installed capacity amounts to 1,410 MW. Prior to commissioning the nuclear power plant in 1978, the turbine was filled with fresh oil. This turbine oil did not display any significant ageing or operational restrictions in the following 15 years. Based on our experience, we believe that this behaviour is typical for all initial fillings in new plants. Since the beginning of the 90ies, the contamination of the entire turbine cycle has increased due to the precipitation of oil ageing products and additives decomposed by oxygen. Therefore, the initial filling was replaced by a new oil in 1994, without measures to remove ageing products or additive deposits from the oil cycle. Therefore, it is not surprising that after merely four years this oil filling displayed the same properties as the first filling after 15 years. As a consequence, another oil change was urgently required in 1999. (orig.) [de

Electrocapillary Phenomena at Edible Oil/Saline Interfaces.

Science.gov (United States)

Nishimura, Satoshi; Ohzono, Takuya; Shoji, Kohei; Yagihara, Shin; Hayashi, Masafumi; Tanaka, Hisao

2017-03-01

Interfacial tension between edible oil and saline was measured under applied electric fields to understand the electrocapillary phenomena at the edible oil/saline interfaces. The electric responses of saline droplets in edible oil were also observed microscopically to examine the relationship between the electrocapillary phenomena and interfacial polarization. When sodium oleate (SO) was added to edible oil (SO-oil), the interfacial tension between SO-oil and saline decreased. However, no decrease was observed for additive-free oil or oleic acid (OA)-added oil (OA-oil). Microscopic observations suggested that the magnitude of interfacial polarization increased in the order of additive-free oil oil oil. The difference in electrocapillary phenomena between OA- and SO-oils was closely related to the polarization magnitude. In the case of SO-oil, the decrease in interfacial tension was remarkably larger for saline (pH 5.4~5.6) than that for phosphate-buffered saline (PBS, pH 7.2~7.4). However, no difference was observed between the electric responses of PBS and saline droplets in SO-oil. The difference in electrocapillary phenomena for PBS and saline could not be simply explained in terms of polarization magnitude. The ratio of ionized and non-ionized OA at the interfaces changed with the saline pH, possibly leading to the above difference.

Heat transfer characteristics of some oils used for engine cooling

International Nuclear Information System (INIS)

Abou-Ziyan, Hosny Z.

2004-01-01

This paper reports the results of an experimental investigation of heat transfer from a cast iron test specimen to engine oils under boiling conditions. The work is aimed at evaluating the thermal characteristics of some engine oils in contact with high temperature parts in internal combustion engines. Three mono-grade oils and two multi-grade oils are examined at heat fluxes from about 30 to more than 400 kW/m 2 for bulk temperatures of 40, 60, 80, 100, 125, 150 and 175 deg. C. The considered oils are analyzed and tested according to some ASTM standards to determine their additives concentration and to obtain some of their thermophysical properties. The results indicated that oil additives, oil properties and bulk temperatures have substantial effects on the oil characteristics. The boiling heat flux, for the best oil, rises by a factor of 1.65 as the bulk temperature decreases from 175 to 40 deg. C. The mono-grade oils produce superior heat transfer characteristics compared to those produced by multi-grade oils. The oil with the best additive concentrations produces boiling heat fluxes up to 4.44 times higher than those produced by some other oils. Comparing the results of the tested oils revealed that the oil that has the largest concentrations of boron, magnesium, phosphorus and zinc with low concentration of calcium yields the best heat transport characteristics among the other tested oils. These additives provide superior detergent and dispersant characteristics, reflected in the large alkalinity and low corrosivity of the oil. On the other side, calcium has a negative interaction with other additives and yields an adverse effect on heat transfer characteristics even when it exists in oil with large concentrations of boron, magnesium, phosphorus and zinc

Process of deparaffining oils

Energy Technology Data Exchange (ETDEWEB)

1941-03-05

This process comprises centrifuging in the presence of a solvent which dissolves the oil and precipitates the paraffins, with the addition of an auxiliary liquid whose surface tension with respect to the oil solution does not exceed 50 dynes/cm.

The In Vitro Antimicrobial Activity of Lavandula angustifolia Essential Oil in Combination with Other Aroma-Therapeutic Oils

Science.gov (United States)

de Rapper, Stephanie; Kamatou, Guy; Viljoen, Alvaro

2013-01-01

The antimicrobial activity of Lavandula angustifolia essential oil was assessed in combination with 45 other oils to establish possible interactive properties. The composition of the selected essential oils was confirmed using GC-MS with a flame ionization detector. The microdilution minimum inhibitory concentration (MIC) assay was undertaken, whereby the fractional inhibitory concentration (ΣFIC) was calculated for the oil combinations. When lavender oil was assayed in 1 : 1 ratios with other oils, synergistic (26.7%), additive (48.9%), non-interactive (23.7%), and antagonistic (0.7%) interactions were observed. When investigating different ratios of the two oils in combination, the most favourable interactions were when L. angustifolia was combined with Cinnamomum zeylanicum or with Citrus sinensis, against C. albicans and S. aureus, respectively. In 1 : 1 ratios, 75.6% of the essential oils investigated showed either synergistic or additive results, lending in vitro credibility to the use of essential oil blends in aroma-therapeutic practices. Within the field of aromatherapy, essential oils are commonly employed in mixtures for the treatment of infectious diseases; however, very little evidence exists to support the use in combination. This study lends some credence to the concomitant use of essential oils blended with lavender. PMID:23737850

The In Vitro Antimicrobial Activity of Lavandula angustifolia Essential Oil in Combination with Other Aroma-Therapeutic Oils

Directory of Open Access Journals (Sweden)

Stephanie de Rapper

2013-01-01

Full Text Available The antimicrobial activity of Lavandula angustifolia essential oil was assessed in combination with 45 other oils to establish possible interactive properties. The composition of the selected essential oils was confirmed using GC-MS with a flame ionization detector. The microdilution minimum inhibitory concentration (MIC assay was undertaken, whereby the fractional inhibitory concentration (ΣFIC was calculated for the oil combinations. When lavender oil was assayed in 1 : 1 ratios with other oils, synergistic (26.7%, additive (48.9%, non-interactive (23.7%, and antagonistic (0.7% interactions were observed. When investigating different ratios of the two oils in combination, the most favourable interactions were when L. angustifolia was combined with Cinnamomum zeylanicum or with Citrus sinensis, against C. albicans and S. aureus, respectively. In 1 : 1 ratios, 75.6% of the essential oils investigated showed either synergistic or additive results, lending in vitro credibility to the use of essential oil blends in aroma-therapeutic practices. Within the field of aromatherapy, essential oils are commonly employed in mixtures for the treatment of infectious diseases; however, very little evidence exists to support the use in combination. This study lends some credence to the concomitant use of essential oils blended with lavender.

Improvement of stability and carotenoids fraction of virgin olive oils by addition of microalgae Scenedesmus almeriensis extracts.

Science.gov (United States)

Limón, Piedad; Malheiro, Ricardo; Casal, Susana; Acién-Fernández, F Gabriel; Fernández-Sevilla, José M; Rodrigues, Nuno; Cruz, Rebeca; Bermejo, Ruperto; Pereira, José Alberto

2015-05-15

Humans are not capable of synthesizing carotenoids de novo and thus, their presence in human tissues is entirely of dietary origin. Consumption of essential carotenoids is reduced due to the lower intake of fruits and vegetables. Microalgae are a good source of carotenoids that can be exploited. In the present work, carotenoids rich extracts from Scenedesmus almeriensis were added to extra-virgin olive oils at different concentrations (0.1 and 0.21 mg/mL) in order to enhance the consumption of these bioactives. Extracts brought changes in olive oils color, turning them orange-reddish. Quality of olive oils was improved, since peroxidation was inhibited. Olive oils fatty acids and tocopherols were not affected. β-carotene and lutein contents increase considerably, as well as oxidative stability, improving olive oils shelf-life and nutritional value. Inclusion of S. almeriensis extracts is a good strategy to improve and enhance the consumption of carotenoids, since olive oil consumption is increasing. Copyright © 2014 Elsevier Ltd. All rights reserved.

Detection of olive oil adulteration by low-field NMR relaxometry and UV-Vis spectroscopy upon mixing olive oil with various edible oils

Directory of Open Access Journals (Sweden)

S. Ok

2017-03-01

Full Text Available Adulteration of olive oil using unhealthy substitutes is considered a threat for public health. Low-field (LF proton (1H nuclear magnetic resonance (NMR relaxometry and ultra-violet (UV visible spectroscopy are used to detect adulteration of olive oil. Three different olive oil with different oleoyl acyl contents were mixed with almond, castor, corn, and sesame oils with three volumetric ratios, respectively. In addition, Arbequina olive oil was mixed with canola, flax, grape seed, peanut, soybean, and sunflower seed oils with three volumetric ratios. Transverse magnetization relaxation time (T2 curves were fitted with bi-exponential decaying functions. T2 times of each mixture of olive oils and castor oils, and olive oils and corn oils changed systematically as a function of volumetric ratio. To detect the adulteration in the mixtures with almond and sesame oils, both LF 1H NMR relaxometry and UV-Vis spectroscopy were needed, where UV-Vis-spectroscopy detected the adulteration qualitatively. In the mixtures of Arbequina olive oil and flax, peanut, soybean, and sunflower seed oils, both T21 and T22 values became longer systematically as the content of the olive oil was decreased. The unique UV-Vis maximum absorbance of flax oil at 320.0 nm shows the adulteration of olive oil qualitatively.

Detection of olive oil adulteration by low-field NMR relaxometry and UV-Vis spectroscopy upon mixing olive oil with various edible oils

International Nuclear Information System (INIS)

Ok, S.

2017-01-01

Adulteration of olive oil using unhealthy substitutes is considered a threat for public health. Low-field (LF) proton (1H) nuclear magnetic resonance (NMR) relaxometry and ultra-violet (UV) visible spectroscopy are used to detect adulteration of olive oil. Three different olive oil with different oleoyl acyl contents were mixed with almond, castor, corn, and sesame oils with three volumetric ratios, respectively. In addition, Arbequina olive oil was mixed with canola, flax, grape seed, peanut, soybean, and sunflower seed oils with three volumetric ratios. Transverse magnetization relaxation time (T2) curves were fitted with bi-exponential decaying functions. T2 times of each mixture of olive oils and castor oils, and olive oils and corn oils changed systematically as a function of volumetric ratio. To detect the adulteration in the mixtures with almond and sesame oils, both LF 1H NMR relaxometry and UV-Vis spectroscopy were needed, where UV-Vis-spectroscopy detected the adulteration qualitatively. In the mixtures of Arbequina olive oil and flax, peanut, soybean, and sunflower seed oils, both T21 and T22 values became longer systematically as the content of the olive oil was decreased. The unique UV-Vis maximum absorbance of flax oil at 320.0 nm shows the adulteration of olive oil qualitatively. [es

Enhanced Oil Recovery with Application of Enzymes

DEFF Research Database (Denmark)

Khusainova, Alsu

Enzymes have recently been reported as effective enhanced oil recovery (EOR) agents. Both laboratory and field tests demonstrated significant increase in the ultimate oil production. Up to16% of additional oil was produced in the laboratory conditions and up to 269 barrels of additional oil per day...... were recovered in the field applications. The following mechanisms were claimed to be responsible for the enhancement of the oil production due to enzymes: wettability improvement of the rock surface; formation of the emulsions; reduction of oil viscosity; and removal of high molecular weight paraffins....... However, the positive effect of enzymes on oil recovery is not that obvious. In most of the studies commercial enzyme products composed of enzymes, surfactants and stabilisers were used. Application of such samples makes it difficult to assign a positive EOR effect to a certain compound, as several...

Oils; lubricants; paraffin-wax compositions; hydrocarbon condensation products

Energy Technology Data Exchange (ETDEWEB)

1934-04-04

Petroleum hydrocarbons such as gasoline, kerosene, Diesel fuel oil, lubricating-oil, and paraffin wax, and like hydrocarbons such as are obtainable from shale oil and by the hydrogenation of carbonaceous materials, are improved by addition of products obtained by condensing a cyclic hydrocarbon with a saturated dihalogen derivative of an aliphatic hydrocarbon containing less than five carbon atoms. The addition of the condensation products increases the viscosity of the hydrocarbon oils specified, and is particularly useful in the case of lubricating-oils; addition of the condensation products to paraffin wax increases the transparency and adherent properties of the wax, and is useful in the manufacture of moulded articles such as candles; the products may also be used in solid lubricating-compositions.

Research on oil recovery mechanisms in heavy oil reservoirs

Energy Technology Data Exchange (ETDEWEB)

Kovscek, Anthony R.; Brigham, William E., Castanier, Louis M.

2000-03-16

The research described here was directed toward improved understanding of thermal and heavy-oil production mechanisms and is categorized into: (1) flow and rock properties, (2) in-situ combustion, (3) additives to improve mobility control, (4) reservoir definition, and (5) support services. The scope of activities extended over a three-year period. Significant work was accomplished in the area of flow properties of steam, water, and oil in consolidated and unconsolidated porous media, transport in fractured porous media, foam generation and flow in homogeneous and heterogeneous porous media, the effects of displacement pattern geometry and mobility ratio on oil recovery, and analytical representation of water influx.

Microbial hydrocarbon degradation - bioremediation of oil spills

Energy Technology Data Exchange (ETDEWEB)

Atlas, R M [Louisville Univ., KY (United States). Dept. of Biology

1991-01-01

Bioremediation has become a major method employed in restoration of oil-polluted environments that makes use of natural microbial biodegradative activities. Bioremediation of petroleum pollutants overcomes the factors limiting rates of microbial hydrocarbon biodegradation. Often this involves using the enzymatic capabilities of the indigenous hydrocarbon-degrading microbial populations and modifying environmental factors, particularly concentrations of molecular oxygen, fixed forms of nitrogen and phosphate to achieve enhanced rates of hydrocarbon biodegradation. Biodegradation of oily sludges and bioremediation of oil-contaminated sites has been achieved by oxygen addition-e.g. by tilling soils in landfarming and by adding hydrogen peroxide or pumping oxygen into oiled aquifers along with addition of nitrogen- and phosphorous-containing fertilizers. The success of seeding oil spills with microbial preparations is ambiguous. Successful bioremediation of a major marine oil spill has been achieved based upon addition of nitrogen and phosphorus fertilizers. (author).

Polymercaptanized soybean oil – properties and tribological characterization

Science.gov (United States)

Polymercaptanized vegetable oils are produced in industrial scale by the addition of hydrogen sulfide across double bonds or epoxides of vegetable oils, in the presence of UV-light. To date, soybean oil, epoxidized soybean oil, and castor oil has been mercaptanized using such a procedure. Depending ...

CONSIDERATIONS ABOUT THE USE OF LOVAGE LEAVES TO IMPROVE THE QUALITY OF EDIBLE VEGETABLE OILS AND OIL BLENDS

Directory of Open Access Journals (Sweden)

GEIDA SEVDAGUL SULIMAN

2018-03-01

Full Text Available We studied four edible vegetable oils and nine oil blends based on refined sunflower oil, in order to improve the quality characteristics of sunflower oil. The oils used for blends were linseed oil, grapeseed oil, and coconut oil. The physico-chemical properties demonstrated the superior features for oil blends, like lower acidity (measured by acid value and higher stability to autoxidation (measured by peroxide value and refractive index. The best combination for sunflower oil was with coconut oil (lower acidity, higher stability to autoxidation. For a supplementary improvement of properties, especially for the preservation of oils and oil blends, we tested the lovage (Levisticum officinale extract as additive. The obtained additivated mixtures demonstrated better quality characteristics, which recommend them for the human consumption.

Efficient way of importing crude oil from oil producing countries - A review on diversification policy of crude oil import

Energy Technology Data Exchange (ETDEWEB)

Lee, Dal Sok [Korea Energy Economics Institute, Euiwang (Korea)

1999-03-01

Since the second oil crisis, the government has operated the import diversification support program to reduce the risk of crude oil import from Middle-East region and to raise the ability of dealing with the risk. This study tried to seek policy trends in future through reviewing the market environment related to the crude oil import diversification policy and the goal, instrument and effect of the policy. The supply and demand of crude oil and the price are influenced by market system in the world oil market and there are various types of crude oil trading available to both sellers and buyers. There is a probability that the suspension of supply in a certain area could be led to the price issue rather than the physical use of crude oil. In addition, the advantage of price with long-term contract of crude oil was abolished since the price of crude oil imported by term contract has been linked to spot prices. As a result, it is shown that the potential benefit from crude oil import diversification policy is reduced although political and social insecurity still exists in Middle-East region. Therefore, it is desirable to maintain the existing support program until the amount of stored oil reaches the optimum level and to help private enterprises determine the import considering economical efficiency and risk. (author). 36 refs., 5 figs., 23 tabs.

Oxidative stability of fish oil enriched drinking yoghurt

DEFF Research Database (Denmark)

Nielsen, Nina Skall; Debnath, D.; Jacobsen, Charlotte

2007-01-01

The oxidative stability of fish oil enriched drinking yoghurt as well as the antioxidative effect of citric acid ester, vitamin K and disodium ethylenediaminetetraacetic acid (EDTA) were investigated by measuring peroxide value and volatile secondary oxidation products and by sensory analysis....... No oxidation was observed in yoghurt stored at 2 [degree sign]C for up to 19 days, with or without addition of citric acid ester. Fish oil enriched yoghurt was also very stable even when compared to yoghurt with added rapeseed oil or a mixture of rapeseed oil and fish oil stored for up to 29 days. The addition...

Profiling of Indigenous Microbial Community Dynamics and Metabolic Activity During Enrichment in Molasses-Supplemented Crude Oil-Brine Mixtures for Improved Understanding of Microbial Enhanced Oil Recovery.

Science.gov (United States)

Halim, Amalia Yunita; Pedersen, Dorthe Skou; Nielsen, Sidsel Marie; Lantz, Anna Eliasson

2015-06-01

Anaerobic incubations using crude oil and brine from a North Sea reservoir were conducted to gain increased understanding of indigenous microbial community development, metabolite production, and the effects on the oil-brine system after addition of a complex carbon source, molasses, with or without nitrate to boost microbial growth. Growth of the indigenous microbes was stimulated by addition of molasses. Pyrosequencing showed that specifically Anaerobaculum, Petrotoga, and Methanothermococcus were enriched. Addition of nitrate favored the growth of Petrotoga over Anaerobaculum. The microbial growth caused changes in the crude oil-brine system: formation of oil emulsions, and reduction of interfacial tension (IFT). Reduction in IFT was associated with microbes being present at the oil-brine interphase. These findings suggest that stimulation of indigenous microbial growth by addition of molasses has potential as microbial enhanced oil recovery (MEOR) strategy in North Sea oil reservoirs.

Petrophysical studies in heavy oil sands with early water production - Hamaca area, Orinoco Oil Belt

Energy Technology Data Exchange (ETDEWEB)

Salisch, H.A.

1982-07-01

This study describes the main lines of petrophysical research in the Hamaca-Pao region of the Orinoco Oil Belt. The techniques and parameters most appropriate for petrophysical studies in the area of interest are discussed. Field tests have confirmed the conclusions of this study on early water production and low oil recovery. Steam injection was shown to be a means for increasing oil mobility to such a degree that significant amounts of additional oil can be produced.

Influence of Oil Viscosity on Alkaline Flooding for Enhanced Heavy Oil Recovery

Directory of Open Access Journals (Sweden)

Yong Du

2013-01-01

Full Text Available Oil viscosity was studied as an important factor for alkaline flooding based on the mechanism of “water drops” flow. Alkaline flooding for two oil samples with different viscosities but similar acid numbers was compared. Besides, series flooding tests for the same oil sample were conducted at different temperatures and permeabilities. The results of flooding tests indicated that a high tertiary oil recovery could be achieved only in the low-permeability (approximately 500 mD sandpacks for the low-viscosity heavy oil (Zhuangxi, 390 mPa·s; however, the high-viscosity heavy oil (Chenzhuang, 3450 mPa·s performed well in both the low- and medium-permeability (approximately 1000 mD sandpacks. In addition, the results of flooding tests for the same oil at different temperatures also indicated that the oil viscosity put a similar effect on alkaline flooding. Therefore, oil with a high-viscosity is favorable for alkaline flooding. The microscopic flooding test indicated that the water drops produced during alkaline flooding for oils with different viscosities differed significantly in their sizes, which might influence the flow behaviors and therefore the sweep efficiencies of alkaline fluids. This study provides an evidence for the feasibility of the development of high-viscosity heavy oil using alkaline flooding.

Sensory and chemical stability in coated peanuts with the addition of essential oils and synthetic antioxidants

Directory of Open Access Journals (Sweden)

Olmedo, R. H.

2012-03-01

Full Text Available The objective of this work was to evaluate the antioxidant effect of essential oils on the oxidative stability of coated peanuts. Untreated coated peanuts (CP and treated coated peanuts with the addition of rosemary (CP-R, oregano (CP-O and laurel (CP-L essential oils and BHT (CPBHT were prepared. Peroxide values (PV and p-anisidine values (AV and the intensity ratings of sensory attributes by descriptive analysis were measured during 112 days of storage at room temperature (23°C. CP-BHT exhibited the lowest PV and AV increase. CP-R, CP-O and CP-L showed lower rates of increase in PV and AV than CP. The oxidized and cardboard flavor intensity ratings increased much more in CP during storage than the other studied products. CPBHT also showed the lowest increase in the intensity ratings of these sensory attributes. Three essential oils, namely, laurel, oregano and rosemary showed antioxidant activity and increased the shelf life of coated peanuts.

El objetivo de este trabajo fue evaluar el efecto antioxidante de aceites esenciales sobre la estabilidad oxidativa en maní recubiertos. Se prepararon maníes recubiertos sin agregados (CP, y con el agregado de aceites esenciales de romero (CP-R, orégano (CP-O y laurel (CP-L y BHT (CPBHT. Se midieron, durante 112 días de almacenamiento, los valores de peróxidos (PV y p-anisidina (AV, y las intensidades de atributos sensoriales mediante análisis descriptivo. CP-BHT presentó el menor valor de PV y AV. CP-R, CP-O y CP-L tuvieron mayor PV y AV respecto a CP. Los valores de intensidad del sabor oxidado y cartón tuvieron un mayor incremento en CP durante el almacenamiento con respecto a los otros productos estudiados. La muestra CP-BHT también mostró los menores valores de intensidad de estos atributos sensoriales. Los aceites esenciales de laurel, orégano y romero presentaron actividad antioxidante e incrementaron la vida útil del maní recubierto.

Essential oils and anxiolytic aromatherapy.

Science.gov (United States)

Setzer, William N

2009-09-01

A number of essential oils are currently in use as aromatherapy agents to relieve anxiety, stress, and depression. Popular anxiolytic oils include lavender (Lavandula angustifolia), rose (Rosa damascena), orange (Citrus sinensis), bergamot (Citrus aurantium), lemon (Citrus limon), sandalwood (Santalum album), clary sage (Salvia sclarea), Roman chamomile (Anthemis nobilis), and rose-scented geranium (Pelargonium spp.). This review discusses the chemical constituents and CNS effects of these aromatherapeutic essential oils, as well as recent studies on additional essential oils with anxiolytic activities.

21 CFR 172.723 - Epoxidized soybean oil.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Epoxidized soybean oil. 172.723 Section 172.723... CONSUMPTION Other Specific Usage Additives § 172.723 Epoxidized soybean oil. Epoxidized soybean oil may be... reacting soybean oil in toluene with hydrogen peroxide and formic acid. (b) It meets the following...

An analysis of price and volatility transmission in butter, palm oil and crude oil markets

Directory of Open Access Journals (Sweden)

Dennis Bergmann

2016-11-01

Full Text Available Abstract Recent changes to the common agricultural policy (CAP saw a shift to greater market orientation for the EU dairy industry. Given this reorientation, the volatility of EU dairy commodity prices has sharply increased, creating the need to develop proper risk management tools to protect farmers’ income and to ensure stable prices for processors and consumers. In addition, there is a perceived threat that these commodities may be replaced by cheaper substitutes, such as palm oil, as dairy commodity prices become more volatile. Global production of palm oil almost doubled over the last decade while butter production remained relatively flat. Palm oil also serves as a feedstock for biodiesel production, thus establishing a new link between agricultural commodities and crude oil. Price and volatility transmission effects between EU and World butter prices, as well as between butter, palm oil and crude oil prices, before and after the Luxembourg agreement, are analysed. Vector autoregression (VAR models are applied to capture price transmission effects between these markets. These are combined with a multivariate GARCH model to account for potential volatility transmission. Results indicate strong price and volatility transmission effects between EU and World butter prices. EU butter shocks further spillover to palm oil volatility. In addition, there is evidence that oil prices spillover to World butter prices and World butter volatility.

Experimentation on bio-kerosene stove using organic additive

Science.gov (United States)

Varshini, M.; Shetty, Divakar

2017-07-01

One of the basic worthy item used in most of the villages even now a day's also is the kerosene stove. But in the current scenario, the petroleum products are been replenished. So an alternate fuel should be found in order delve. This work is to check the contingency of blending pongamia oil and kerosene in which is used as an additive. Pongamia is one of the forest based fast growing evergreen tree which is capable of yielding 9 - 90 kg seeds from which 25% of oil can be extracted. Distilled cow urine is to be used so that the fuel can be stored for longer time and is odorless. Blends of 10% to 70% neat pongamia oil - kerosene(KEP) and pongamia oil - kerosene with additive(KEPWA) are prepared. The properties such as flash point, fire point and viscosity are determined. The blends are been compared by doing emission test. The blends with additive showed better properties and reducing in emission characteristics compared to neat blends. It is also observed that emission of CO is decreasing with increasing blends.

Experimental study on kinetics oil oil-suspended particulate matter aggregation

International Nuclear Information System (INIS)

Sun, J.; Environment Canada, Ottawa, ON; Khelifa, A.; Wang, Z.; Brown, C.; Fieldhouse, B.; Yang, C.; Zheng, X.; Wong, S.; So, L.C.

2009-01-01

Past studies of oil spills have shown that oil suspended particulate matter aggregates (OSAs) play a role in enhancing the natural cleansing of oiled shorelines. OSAs result from aggregation between suspended oil droplets and suspended particulate matter (SPM) in aquatic environments. During this process, oil dispersion into the water column is significantly increased since the surface of the oil droplet is surrounded by sediment particles. In addition, the accelerated biodegradation of the oil can be attributed to the greater oil-water contact area. This study focused on the kinetic aspects of OSA formation, with particular reference to the time scale of this process and its significance to oil dispersion following oil spills in water. A laboratory study was conducted to measure the time scale of OSA formation and its variations with mixing conditions. A reciprocating shaker and various oil/sediment mixtures were used to prepare the OSAs. Standard reference material 1941b was used as the natural sediment mixed with Arabian medium crude and artificial seawater under various mixing energies. The sediment-to-oil ratio remained constant for all experiments. Gas chromatography-flame ionization detection (GC-FID) analysis was used to measure the total petroleum hydrocarbons (TPH) trapped in negatively buoyant OSAs. Results showed that the TPH in OSAs increased exponentially with shaking time and reached an equilibrium value within 3 hours. The equilibrium decreased from 3 hours to 1.3 hours when the shaking rate increased from 2.0 to 2.3 Hz. It was concluded that high mixing energy enhances OSA formation and shortens the time for OSA formation. 42 refs., 6 tabs., 5 figs

Experimental study on kinetics oil oil-suspended particulate matter aggregation

Energy Technology Data Exchange (ETDEWEB)

Sun, J. [Ocean Univ. of China, Qingdoa (China). Environmental Science and Engineering Inst.; Environment Canada, Ottawa, ON (Canada). Emergencies Science and Technology Section, Emergencies, Operational Analytical Laboratories and Research Support Division; Khelifa, A.; Wang, Z.; Brown, C.; Fieldhouse, B.; Yang, C. [Environment Canada, Ottawa, ON (Canada). Emergencies Science and Technology Section, Emergencies, Operational Analytical Laboratories and Research Support Division; Zheng, X. [Ocean Univ. of China, Qingdoa (China). Environmental Science and Engineering Inst.; Wong, S. [Ottawa Univ., ON (Canada). Dept. of Chemistry; So, L.C. [Waterloo Univ., ON (Canada). Faculty of Engineering

2009-07-01

Past studies of oil spills have shown that oil suspended particulate matter aggregates (OSAs) play a role in enhancing the natural cleansing of oiled shorelines. OSAs result from aggregation between suspended oil droplets and suspended particulate matter (SPM) in aquatic environments. During this process, oil dispersion into the water column is significantly increased since the surface of the oil droplet is surrounded by sediment particles. In addition, the accelerated biodegradation of the oil can be attributed to the greater oil-water contact area. This study focused on the kinetic aspects of OSA formation, with particular reference to the time scale of this process and its significance to oil dispersion following oil spills in water. A laboratory study was conducted to measure the time scale of OSA formation and its variations with mixing conditions. A reciprocating shaker and various oil/sediment mixtures were used to prepare the OSAs. Standard reference material 1941b was used as the natural sediment mixed with Arabian medium crude and artificial seawater under various mixing energies. The sediment-to-oil ratio remained constant for all experiments. Gas chromatography-flame ionization detection (GC-FID) analysis was used to measure the total petroleum hydrocarbons (TPH) trapped in negatively buoyant OSAs. Results showed that the TPH in OSAs increased exponentially with shaking time and reached an equilibrium value within 3 hours. The equilibrium decreased from 3 hours to 1.3 hours when the shaking rate increased from 2.0 to 2.3 Hz. It was concluded that high mixing energy enhances OSA formation and shortens the time for OSA formation. 42 refs., 6 tabs., 5 figs.

Improvement of phenolic antioxidants and quality characteristics of virgin olive oil with the addition of enzymes and nitrogen during olive paste processing

Directory of Open Access Journals (Sweden)

Iconomou, D.

2010-09-01

Full Text Available The evolution of phenolic compounds and their contribution to the quality characteristics in virgin olive oil during fruit processing was studied with the addition of a combination of various commercial enzymes containing pectinases, polygalacturonases, cellulase and β-glucanase with or without nitrogen flush. Olive fruits (Olea europaea, L. of the cultivar Megaritiki, at the semi black pigmentation stage of maturity, were used in a 3-phase extraction system in an experiment at industrial scale. The addition of enzymes in the olive paste during processing increased the total phenol and ortho-diphenol contents, as well as some simple phenolic compounds (3,4-DHPEA, p-HPEA and the secoiridoid derivatives (3,4-DHPEA-EDA and 3,4-DHPEAEA in olive oil and therefore improved its oxidative stability. Furthermore, enzyme treatment ameliorated the quality parameters of the produced olive oil (acidity and peroxide value and their sensory attributes. The use of additional N2 flush with the enzyme treatments did not improve the quality parameters of olive oil any further; however it did not affect the concentration of individual and total sterols or most of the fatty acid composition. Consequently, olive paste treatment with enzymes not only improved the quality characteristics of olive oil and enhanced the overall ogranoleptic quality, but also increased the olive oil yield.

La evolución de los compuestos fenólicos y su contribución a las caracterísiticas de calidad de aceite de oliva virgen durante el procesado del fruto fue estudiado mediante la adición de una combinación de varias enzimas comerciales conteniendo pectinasas, poligalacturonasa, celulasa y β-glucanasa con y sin flujo de nitrógeno. Las aceitunas (Olea europaea, L. de la variedad Megaritiki, con un estado de madurez correspondiente a una pigmentación semi-negra, fueron usadas en un experimento a escala industrial mediante un sistema de extracción de 3-fase. La

Refining mineral oils

Energy Technology Data Exchange (ETDEWEB)

1946-07-05

A process is described refining raw oils such as mineral oils, shale oils, tar, their fractions and derivatives, by extraction with a selected solvent or a mixture of solvents containing water, forming a solvent more favorable for the hydrocarbons poor in hydrogen than for hydrocarbons rich in hydrogen, this process is characterized by the addition of an aiding solvent for the water which can be mixed or dissolved in the water and the solvent or in the dissolving mixture and increasing in this way the solubility of the water in the solvent or the dissolving mixture.

The effect of fish oil supplements on blood pressure.

Science.gov (United States)

Lofgren, R P; Wilt, T J; Nichol, K L; Crespin, L; Pluhar, R; Eckfeldt, J

1993-01-01

We conducted a double-blind, placebo-controlled crossover study to determine the effects of fish oil supplementation on blood pressure in middle-aged men. Subjects were randomly assigned to consume either 20 g of fish oil or safflower oil for 12 weeks and then consume the other oil for an additional 12 weeks after a 4-week washout period. We found no significant changes from the pretreatment value in systolic or diastolic blood pressure with the use of fish oil supplements. In addition, there were no significant differences in the posttreatment blood pressures comparing the fish and safflower oil phases of the study. PMID:8427339

[Total analysis of organic rubber additives].

Science.gov (United States)

He, Wen-Xuan; Robert, Shanks; You, Ye-Ming

2010-03-01

In the present paper, after middle pressure chromatograph separation using both positive phase and reversed-phase conditions, the organic additives in ethylene-propylene rubber were identified by infrared spectrometer. At the same time, by using solid phase extraction column to maintain the main component-fuel oil in organic additves to avoid its interfering with minor compounds, other organic additves were separated and analysed by GC/Ms. In addition, the remaining active compound such as benzoyl peroxide was identified by CC/Ms, through analyzing acetone extract directly. Using the above mentioned techniques, soften agents (fuel oil, plant oil and phthalte), curing agent (benzoylperoxide), vulcanizing accelerators (2-mercaptobenzothiazole, ethyl thiuram and butyl thiuram), and antiagers (2, 6-Di-tert-butyl-4-methyl phenol and styrenated phenol) in ethylene-propylene rubber were identified. Although the technique was established in ethylene-propylene rubber system, it can be used in other rubber system.

Manitoba 2004 oil activity review

International Nuclear Information System (INIS)

Fox, J.N.

2005-01-01

This paper presented data on oil and gas activities in Manitoba during 2004, the busiest year in Manitoba's oil patch since the mid 1980s. Increases in the leasing of Crown and freehold acreage were also noted, with accompanying increases in drilling activity for the latter part of 2004. Details of Crown land sales were presented, with a total of 43,725 hectares of crown oil and gas rights under lease. During 2004, over 15,000 hectares of Crown oil and gas leases were sold, the highest figures since 1997. More wells were licensed and drilled in 2004 than in any year since 1986. Overall drilling success rate was 96.7 per cent. Details of top drillers in Manitoba were presented, with drilling activity focused in Waskada and Daly fields and the Sinclair area. Oil production increased by 0.7 per cent, with 1474 wells in production. Daily oil production statistics were presented, with the total value of Manitoba's oil production being $196 million. Details of the top 5 producers were provided, in addition to details of horizontal well production. Recent developments in Sinclair Field, Pierson L. Amaranth MC 3b A Pool, Waskada L. Amaranth I Pool and Virden Lodgepole D Pool were reviewed. The Manitoba Drilling Incentive Program was discussed with reference to the following enhancements: new well incentives, horizontal well incentives; holiday oil volume accounts; and marginal well major workover programs. Various Oil and Gas Act amendments were reviewed. In addition, the Williston Basin Architecture and Hydrocarbon Potential Project was discussed. 3 figs

Recycling used palm oil and used engine oil to produce white bio oil, bio petroleum diesel and heavy fuel

Science.gov (United States)

Al-abbas, Mustafa Hamid; Ibrahim, Wan Aini Wan; Sanagi, Mohd. Marsin

2012-09-01

Recycling waste materials produced in our daily life is considered as an additional resource of a wide range of materials and it conserves the environment. Used engine oil and used cooking oil are two oils disposed off in large quantities as a by-product of our daily life. This study aims at providing white bio oil, bio petroleum diesel and heavy fuel from the disposed oils. Toxic organic materials suspected to be present in the used engine oil were separated using vacuum column chromatography to reduce the time needed for the separation process and to avoid solvent usage. The compounds separated were detected by gas chromatography-mass spectrometry (GC-MS) and found to contain toxic aromatic carboxylic acids. Used cooking oils (thermally cracked from usage) were collected and separated by vacuum column chromatography. White bio oil produced was examined by GC-MS. The white bio oil consists of non-toxic hydrocarbons and is found to be a good alternative to white mineral oil which is significantly used in food industry, cosmetics and drugs with the risk of containing polycyclic aromatic compounds which are carcinogenic and toxic. Different portions of the used cooking oil and used engine were mixed to produce several blends for use as heavy oil fuels. White bio oil was used to produce bio petroleum diesel by blending it with petroleum diesel and kerosene. The bio petroleum diesel produced passed the PETRONAS flash point and viscosity specification test. The heat of combustion of the two blends of heavy fuel produced was measured and one of the blends was burned to demonstrate its burning ability. Higher heat of combustion was obtained from the blend containing greater proportion of used engine oil. This study has provided a successful recycled alternative for white bio oil, bio petroleum fuel and diesel which can be an energy source.

Enzymatic interesterification of vegetable oil/ fish oil blend for margarine production

DEFF Research Database (Denmark)

Ibrahim, Nuzul Amri Bin; Xu, Xuebing

the desired properties. In this study, palm stearin (PS), palm kernel oil (PKO) and fish oil (FO) are blended and modified by enzymatic interesterification. PS functioned as the hard stock, PKO as the soft oil and FO as a source for eicosapentaenoic acid (EPA)/ docosahexaenoic acid (DHA). The purpose...... cause the product to be susceptible to oxidation due to the presence of high content of polyunsaturated fatty acids. Furthermore, FO could also influence the melting properties of the product. Therefore, in addition to determining the fatty acid position on the glycerol backbone, it is also pertinent...

Canada's crude oil resources : crude oil in our daily lives

International Nuclear Information System (INIS)

Bott, R.

2001-10-01

Created in 1975, the Petroleum Communication Foundation is a not-for-profit organization. The objective of the Foundation is to inform Canadians about the petroleum industry in Canada. It produces educational, fact-based publications and programs, employing a multi-stakeholder review process. The first section of this publication is devoted to crude oil and the benefits that are derived from it. It begins by providing a brief definition of crude oil, then moves to the many uses in our daily lives and the environmental impacts like air pollution, spills, and footprint on the land from exploration and production activities. Section 2 details the many uses of crude oil and identifies the major oil producing regions of Canada. A quick mention is made of non-conventional sources of crude oil. The search for crude oil is the topic of section 3 of the document, providing an overview of the exploration activities, the access rights that must be obtained before gaining access to the resource. The drilling of oil is discussed in section 4. Section 5 deals with issues pertaining to reservoirs within rocks, while section 6 covers the feeding of the refineries, discussing topics from the movement of oil to market to the refining of the crude oil, and the pricing issues. In section 7, the uncertain future is examined with a view of balancing the supply and demand, as crude oil is a non-renewable resource. Supplementary information is provided concerning additional publications published by various organizations and agencies. figs

Detection of sunflower oil in extra virgin olive oil by fast differential scanning calorimetry

NARCIS (Netherlands)

Wetten, I.A.; Herwaarden, A.W.; Splinter, R.; Boerrigter-Eenling, R.; Ruth, van S.M.

2015-01-01

Extra virgin olive oil (EVOO) is an economically valuable product, due to its high quality and premium price. Therefore it is vulnerable for adulteration by means of the addition of cheaper vegetable oils. Differential scanning calorimetry (DSC) has been suggested as a fast technique for the

Active oil-water interfaces: buckling and deformation of oil drops by bacteria

Science.gov (United States)

Juarez, Gabriel; Stocker, Roman

2014-11-01

Bacteria are unicellular organisms that seek nutrients and energy for growth, division, and self-propulsion. Bacteria are also natural colloidal particles that attach and self-assemble at liquid-liquid interfaces. Here, we present experimental results on active oil-water interfaces that spontaneously form when bacteria accumulate or grow on the interface. Using phase-contrast and fluorescence microscopy, we simultaneously observed the dynamics of adsorbed Alcanivorax bacteria and the oil-water interface within microfluidic devices. We find that, by growing and dividing, adsorbed bacteria form a jammed monolayer of cells that encapsulates the entire oil drop. As bacteria continue to grow at the interface, the drop buckles and the interface undergoes strong deformations. The bacteria act to stabilize non-equilibrium shapes of the oil-phase such wrinkling and tubulation. In addition to presenting a natural example of a living interface, these findings shape our understanding of microbial degradation of oil and may have important repercussions on engineering interventions for oil bioremediation.

Effect of ultrasonic intensity and frequency on oil/heavy-oil recovery from different wettability rocks

Energy Technology Data Exchange (ETDEWEB)

Naderi, K.; Babadagli, T. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Alberta Univ., Edmonton, AB (Canada)

2008-10-15

This study identified the mechanisms that are responsible for additional oil recovery that is often observed following an earthquake. It focused on the theory that harmonics of low frequency waves create high frequency waves as they penetrate into rock formations. A series of experiments were conducted on oil-wet rocks with high oil viscosities. The objective was to better understand how ultrasonic energy affects oil recovery at core and pore scale. Cylindrical sandstone cores were placed in imbibition cells to examine how the presence of initial water saturation can affect recovery, and how the recovery changes for different oil viscosities. An increase in oil recovery was observed with ultrasonic energy in all cases. The additional recovery with ultrasonic energy lessened as the oil viscosity increased. Ultrasonic intensity and frequency were shown to be critical to the performance, which is important since ultrasonic waves have limited penetration into porous medium. This is a key disadvantage for commercializing this promising process for well stimulation. Therefore, the authors designed a set-up to measure the ultrasonic energy penetration capacity in different media, notably air, water and slurry. The set-up could identify which types of reservoirs are most suitable for ultrasonic application. Imbibition experiments revealed that ultrasonic radiation increases recovery, and is much more significant in oil wet cases, where initial water saturation facilitate oil recovery. Higher frequency showed a higher rate of recovery compared to lower frequency, but the ultimate recovery was not changed substantially. 46 refs., 1 tab., 16 figs.

HFRR investigation of biobased and petroleum based oils

Science.gov (United States)

Biobased oils come in a wide range of chemical structures as do petroleum based oils. In addition, a distinct structural difference exists between these two broad categories of oils. Previous work has shown that, in spite of the structural differences, these two categories of oils display similar pr...

Oil shale, shale oil, shale gas and non-conventional hydrocarbons

Directory of Open Access Journals (Sweden)

Clerici A.

2015-01-01

Full Text Available In recent years there has been a world “revolution” in the field of unconventional hydrocarbon reserves, which goes by the name of “shale gas”, gas contained inside clay sediments micropores. Shale gas finds particular development in the United States, which are now independent of imports and see a price reduction to less than one third of that in Europe. With the high oil prices, in addition to the non-conventional gas also “oil shales” (fine-grained sedimentary rocks that contain a large amount of organic material to be used both to be directly burned or to extract liquid fuels which go under the name of shale oil, extra heavy oils and bitumen are becoming an industrial reality. Both unconventional gas and oil reserves far exceed in the world the conventional oil and gas reserves, subverting the theory of fossil fuels scarcity. Values and location of these new fossil reserves in different countries and their production by comparison with conventional resources are presented. In view of the clear advantages of unconventional fossil resources, the potential environmental risks associated with their extraction and processing are also highlighted.

Oxidative desulfurization of tire pyrolysis oil

Directory of Open Access Journals (Sweden)

Ahmad Shahzad

2016-01-01

Full Text Available This paper presents a low cost method for the purification of oils obtained from the pyrolysis of used tires. Oxidative desulfurization is a promising route for purification of tire pyrolysis oils as hydro-desulfurization may not be affordable for small scale industries. Different additives and acids have been employed for the enhancement of properties of pyrolytic oils. The experimental conditions were kept identical throughout, i.e. atmospheric pressure and 50°C temperature for comparison of performance of various additives. The use of hydrogen peroxide-acetic acid mixture (10 wt.% was found more economical and effective in desulfurization and improvement of fuel properties of sample oils. The contribution of sulfuric acid in desulfurization and decreasing viscosity was also satisfactory but due to high price of concentrated sulfuric acid its use may not be economical. Calcium oxide and Fuller’s earth was not found to be effective in desulfurization. Results indicate that oxidative desulfurization could render tire pyrolysis oils suitable for blending as heating fuel.

Tragacanth gum: an effective oil well drilling fluid additive

Energy Technology Data Exchange (ETDEWEB)

Mahto, V.; Sharma, V. [Indian School of Mines, Dhanbad (India). Department of Petroleum Engineering

2005-02-15

The low penetration rate, excessive torque and drag, poor hole cleaning and formation damage are major impediments in drilling oil and gas well. These have a major impact on drilling efficiency and well economics. Keeping these in mind, an attempt was made to design a water based drilling fluid system using Indian bentonite clays and tragacanth gum. The effect of tragacanth gum on rheological behavior of three different Indian bentonite water suspensions was studied and a drilling fluid system was developed. The filtrates of these drilling fluids were subjected to formation damage study on the field core using Ruska Liquid Permeameter. The laboratory investigation furnishes that tragacanth gum acts as a good viscosifier and fluid loss control agent. The drilling fluid filtrate also has less effect on formation damage. (author)

Exposure to mutagenic aldehydes and particulate matter during panfrying of beefsteak with margarine, rapeseed oil, olive oil or soybean oil.

Science.gov (United States)

Sjaastad, Ann Kristin; Svendsen, Kristin

2008-11-01

The aim of the study was to see if a cook could be exposed to mutagenic aldehydes in fumes from frying of beefsteak using margarine, rapeseed oil, soybean oil or virgin olive oil as frying fat. In addition, levels of particle exposure were measured to make the results comparable to other studies. The levels of higher aldehydes and total particles were measured in the breathing zone of the cook during the panfrying of beefsteak with the four different frying fats. In addition, the number of particles in the size intervals 0.3-0.5, 0.5-0.7 and 0.7-1.0 microm in the kitchen was registered. Measured levels of mutagenic aldehydes were between non-detectable and 25.33 microg m(-3) air. The exposure level of total aerosol was between 1.0 and 11.6 mg m(-3). Higher aldehydes were detected in all samples from this study, and mutagenic aldehydes were detected in most of the samples. Frying with margarine gave statistically significantly higher levels of mutagenic aldehydes and particles in all three size fractions than frying with the three different kinds of oil.

Addition of polyurethane dispersions to Portland G for oil wells steam injection submitted to vapor injection; Adicao de poliuretana em dispersao a Portland G para cimentacao de pocos de petroleo sujeitos a injecao de vapor

Energy Technology Data Exchange (ETDEWEB)

Silva, L.B. da; Lima, F.M. de; Martinelli, A.M.; Bezerra, U.T.; Mello, D.M.A. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Araujo, R.G.S. [PETROBRAS, Rio de Janeiro, RJ (Brazil)

2004-07-01

Portland cement is by far the most important binding material used in oil well cementing. The cement sheath is responsible for both the mechanical stability of the wellbore and zonal isolation. During primary cementing and the production lifespan of the well, the cement sheath is exposed to adverse thermo-mechanical conditions, which may crack the intrinsically brittle cement material. Cracking affects the mechanical integrity of the sheath resulting in the contamination of oil or gas pay zones, as well as in the increase of producing costs related to the extraction of pebble and water. This scenario is especially encountered in wells containing heavy oils, typical of the Northeastern region of Brazil. The objective of the present study was to improve the fracture toughness of hardened Special Portland Cement slurries by the addition of aqueous polyurethane to Portland-based slurries used in primary cementing, plug backs and squeeze operations, improving environmental and economical impacts. The results revealed that the addition of polyurethane increased the viscosity of the slurry but still within the limits established by oil well cement guidelines. No significant increase was observed in the compressive strength of the cement. However, the addition of polyurethane improved the toughness of the cement increasing its ability to withstand thermo-mechanical cycles typical of heavy oil recovery. In addition, significant reduction in permeability was observed as the contents of polyurethane increased, contributing to the reduction in set time and gas migration through the cement sheath. (author)

Exploration of process parameters for continuous hydrolysis of canola oil, camelina oil and algal oil

KAUST Repository

Wang, Weicheng

2012-07-01

Thermal hydrolysis of triglycerides to form free fatty acid (FFA) is a well-established industry practice. Recently, this process has been employed as a first step in the production of biofuels from lipids. To that end, batch and continuous hydrolysis of various feedstocks has been examined at the laboratory scale. Canola, the primary feedstock in this paper, camelina and algal oils were converted to high quality FFA. For the different reaction temperatures, the continuous hydrolysis system was found to provide better yields than the laboratory batch system. In addition, CFD simulation with ANSYS-CFX was used to model the performance and reactant/product separation in the continuous, counter-flow reactor. The effects of reaction temperature, water-to-oil ratio (ratio of water and oil volumetric inflow rate), and preheating of the reactants were examined experimentally. Optimization of these parameters has resulted in an improved, continuous process with high mass yields (89-93%, for reactor temperature of 260°C and water-to-oil ratio of 4:1) and energy efficiency (76%, for reactor temperature of 250°C and water-to-oil ratio of 2:1). Based on the product quality and energy efficiency considerations, the reactor temperature of 260°C and water-to-oil ratio of 4:1 have provided the optimal condition for the lab scale continuous hydrolysis reaction. © 2012 Elsevier B.V.

Exploration of process parameters for continuous hydrolysis of canola oil, camelina oil and algal oil

KAUST Repository

Wang, Weicheng; Turner, Timothy L.; Stikeleather, Larry F.; Roberts, William L.

2012-01-01

Thermal hydrolysis of triglycerides to form free fatty acid (FFA) is a well-established industry practice. Recently, this process has been employed as a first step in the production of biofuels from lipids. To that end, batch and continuous hydrolysis of various feedstocks has been examined at the laboratory scale. Canola, the primary feedstock in this paper, camelina and algal oils were converted to high quality FFA. For the different reaction temperatures, the continuous hydrolysis system was found to provide better yields than the laboratory batch system. In addition, CFD simulation with ANSYS-CFX was used to model the performance and reactant/product separation in the continuous, counter-flow reactor. The effects of reaction temperature, water-to-oil ratio (ratio of water and oil volumetric inflow rate), and preheating of the reactants were examined experimentally. Optimization of these parameters has resulted in an improved, continuous process with high mass yields (89-93%, for reactor temperature of 260°C and water-to-oil ratio of 4:1) and energy efficiency (76%, for reactor temperature of 250°C and water-to-oil ratio of 2:1). Based on the product quality and energy efficiency considerations, the reactor temperature of 260°C and water-to-oil ratio of 4:1 have provided the optimal condition for the lab scale continuous hydrolysis reaction. © 2012 Elsevier B.V.

Pre-electrocoalescer unit adapted to the extra-heavy oil characteristics

Energy Technology Data Exchange (ETDEWEB)

Noik, C.; Dalmazzone, C. [IFP, Rueil-Malmaison (France); Glenat, P. [Total, Paris (France)

2008-10-15

This paper described a dehydration process that can break water oil emulsions to mobilize extra heavy oils and bitumen extra heavy oils. The dehydration process is based on solvent mixture with additives injection. It involves large amount of additives, fairly high operating temperatures, solvent addition, and long retention time inside the vessels. The process could be improved by electrocoalescence, thereby reducing the amount of additive and reducing the retention times of vessels to reach oil export specifications. However, commercial electrocoalescence processes are not suitable for extra heavy oils because of the presence of polar heavy components limiting the electrocoalescence effect and therefore, limiting the efficiency of electrostatic coalescer. This paper presented a study whose objective was to determine the most efficient electrocoalescence parameters considering the characteristics of two types of heavy crude oils issued from cold and thermal productions. The paper presented experimental results for electrocoalescence additive selection and for the optimization of electrical parameters. The paper described the materials and methods, including fluids characterization; viscosity; differential scanning calorimetry; dispersion rig; electrical stability tester; and electrocoalescer rig. It was concluded that crude oils produced by thermal production schemes seemed more sensitive to the temperature effect than crudes produced by cold production. 10 refs., 3 tabs., 23 figs.

Study on analysis of waste edible oil with deterioration and removal of acid value, carbonyl value, and free fatty acid by a food additive (calcium silicate).

Science.gov (United States)

Ogata, Fumihiko; Tanaka, Yuko; Tominaga, Hisato; Kangawa, Moe; Inoue, Kenji; Ueda, Ayaka; Iwata, Yuka; Kawasaki, Naohito

2013-01-01

This study investigated the regeneration of waste edible oil using a food additive (calcium silicate, CAS). Waste edible oil was prepared by combined heat and aeration treatment. Moreover, the deterioration of edible oil by combined heat and aeration treatment was greater than that by heat treatment alone. The acid value (AV) and carbonyl value (CV) increased with increasing deterioration; conversely, the tocopherol concentration decreased with increasing deterioration. The specific surface area, pore volume, and mean pore diameter of the 3 CAS formulations used (CAS30, CAS60, and CAS90) were evaluated, and scanning electron microscopic images were taken. The specific surface area increased in the order of CAS30 (115.54 m(2)/g) edible oil was possible with CAS treatment. The AV reduced by 15.2%, 10.8%, and 23.1% by CAS30, CAS60, and CAS90 treatment, respectively, and the CV was reduced by 35.6%, 29.8%, and 31.3% by these 3 treatments, respectively. Moreover, the concentrations of tocopherol and free fatty acids did not change with CAS treatment. The characteristics of CAS were not related to the degree of change of AV and CV. However, the adsorption mechanism of polar and non-polar compounds generated in waste edible oil by CAS was related with the presence of silica gel molecules in CAS. The findings indicated that CAS was useful for the regeneration of waste edible oil.

The behaviour of molybdenum dialkyldithiocarbamate friction modifier additives

International Nuclear Information System (INIS)

Graham, Jocelyn Claire Herries

2001-01-01

In recent years there has been growing concern to produce energy-efficient lubricated components and modem engine oil specifications require lubricants to demonstrate fuel efficiency in standardised engine tests. One important method of producing low friction and thus fuel-efficient lubricants is to use oil-soluble, molybdenum-containing, friction modifier additives. In optimal conditions these additives are able to produce very low friction coefficients, in the range 0.045 to 0.075 in boundary lubrication conditions. Very little is known about the chemical and physical mechanisms by which oil soluble molybdenum additives form low friction films in tribological contacts. Information about their activity could lead to optimal use of these additives in lubricants and, therefore, more efficient engine running. The work outlined in this thesis investigated the behaviour of oil-soluble molybdenum additives and showed that these additives were able to effectively reduce friction in the absence of other additives such as ZnDTP. Their activity was shown to be highly concentration and temperature dependent and was also found to be sensitive to the roughness of the contacting surfaces. Raman spectroscopy was used to analyse the chemical nature of molybdenum-containing reaction films and found that friction reduction indubitably arises from the local formation of platelets (diameter 30-50 nm) of MoS 2 . The formation of MoS 2 -rich films was found to occur only during direct asperity-asperity rubbing of the contacting surfaces (this type of contact being especially prevalent in pure sliding contacts). At elevated temperatures and in the presence of oxidising gases the consumption of MoDTC was monitored. MoDTC concentration dropped until the total value fell below a critical level to reduce friction. The study showed that decay rate of molybdenum-containing species was reduced by the addition of peroxide-decomposing antioxidants. (author)

Oil spill response plan

International Nuclear Information System (INIS)

1999-08-01

The plan outlined in this document specifies the actions that the Canadian Wildlife Service Atlantic Region is mandated to take in the event of an oil spill, or on discovering oiled migratory birds in terrestrial, fresh water, marine and inter-tidal habitats. In addition to describing the role and responsibilities of the Canadian Wildlife Service, the document also describes response plans of other agencies for dealing with all wildlife species affected by oil spills. Reporting paths, the lead agency concept, shared responsibilities with other Canadian Wildlife Service regional offices, provincial agencies, Heritage Canada, non-government wildlife response agencies, oil spill response organizations, and international organizations are outlined. An overview of the reporting and communications process is also provided

Coconut oil extraction by the Java method: An investigation of its potential application in aqueous Jatropha oil extraction

NARCIS (Netherlands)

Marasabessy, A.; Moeis, M.R.; Sanders, J.P.M.; Weusthuis, R.A.

2010-01-01

A traditional Java method of coconut oil extraction assisted by paddy crabs was investigated to find out if crabs or crab-derived components can be used to extract oil from Jatropha curcas seed kernels. Using the traditional Java method the addition of crab paste liberated 54% w w-1 oil from grated

Lipid oxidation in milk, yoghurt, and salad dressing enriched with neat fish oil or pre-emulsified fish oil

DEFF Research Database (Denmark)

Bruni Let, Mette; Jacobsen, Charlotte; Meyer, Anne S.

2007-01-01

stability than fish-oil-enriched dressings, irrespective of the mode of fish oil addition. Yoghurt thus seemed to be a good delivery system of lipids containing n-3 polyunsaturated fatty acids. Different effects of adding fish oil either as neat fish oil or as a fish-oil-in-water emulsion were observed...... of neat fish oil was a good option for preserving the final quality in yoghurt and dressings, but a pre-emulsion may still be considered for the fish oil enrichment of certain food products, for example, milk. Keywords: Fish oil; lipid oxidation; oil-in-water emulsion; n-3 PUFA; milk; yoghurt; salad......Abstract: This study compared the oxidative stabilities of fish-oil-enriched milk, yoghurt, and salad dressing and investigated the effects on oxidation of adding either neat fish oil or a fish-oil-in-water emulsion to these products. Milk emulsions had higher levels of a fishy off...

Long-term Effects of Nutrient Addition and Phytoremediation on Diesel and Crude Oil Contaminated Soils in subarctic Alaska

Science.gov (United States)

Leewis, Mary-Cathrine; Reynolds, Charles M.; Leigh, Mary Beth

2014-01-01

Phytoremediation is a potentially inexpensive method of detoxifying contaminated soils using plants and associated soil microorganisms. The remote locations and cold climate of Alaska provide unique challenges associated with phytoremediation such as finding effective plant species that can achieve successful site clean-up despite the extreme environmental conditions and with minimal site management. A long-term assessment of phytoremediation was performed which capitalized on a study established in Fairbanks in 1995. The original study sought to determine how the introduction of plants (Festuca rubra, Lolium multiflorum), nutrients (fertilizer), or their combination would affect degradation of petroleum hydrocarbon (TPH) contaminated soils (crude oil or diesel) over time. Within the year following initial treatments, the plots subjected to both planting and/or fertilization showed greater overall decreases in TPH concentrations in both the diesel and crude oil contaminated soils relative to untreated plots. We re-examined this field site after 15 years with no active site management to assess the long-term effects of phytoremediation on colonization by native and non-native plants, their rhizosphere microbial communities and on petroleum removal from soil. Native and non-native vegetation had extensively colonized the site, with more abundant vegetation found on the diesel contaminated soils than the more nutrient-poor, more coarse, and acidic crude oil contaminated soils. TPH concentrations achieved regulatory clean up levels in all treatment groups, with lower TPH concentrations correlating with higher amounts of woody vegetation (trees & shrubs). In addition, original treatment type has affected vegetation recruitment to each plot with woody vegetation and more native plants in unfertilized plots. Bacterial community structure also varies according to the originally applied treatments. This study suggests that initial treatment with native tree species in

Electrodeposition of Asphaltenes. 2. Effect of Resins and Additives

DEFF Research Database (Denmark)

Khvostichenko, Daria S; Andersen, Simon Ivar

2010-01-01

Electrodeposition of asphaltenes from oil/heptane, asphaltene/heptane, and asphaltene/heptane/additive mixtures has been investigated. Toluene, native petroleum resins, and a synthetic asphaltene dispersant, p-nonylphenol, were used as additives. The addition of these components led to partial...... dissolution of asphaltenes in heptane. The charge of asphaltenic particles was found to be negative in oil/heptane mixtures and positive in asphaltene/heptane mixtures. In asphaltene/heptane/toluene systems, the charge of the deposit varied from positive to neutral to negative, depending upon the method...

ECONOMIC CONSEQUENCES OF PEAK OIL FOR THE MAJOR MULTINATIONAL OIL AND GAS COMPANIES

Directory of Open Access Journals (Sweden)

Antonio García-Amate

2018-03-01

Full Text Available The main goal of this work is to analyze the financial statements of the five major multinational oil and gas companies, for the 2011-2015 period, in the framework of the peak oil phenomenon. Peak oil can affect key financial indicators (e.g., earnings volatility, leverage that are used by managers, investors, and stockholders and which may potentially lead to changes in the decision making by management. Our results show that the decline in oil production affects the decisions about investment in new oil wells, leverage, dividends paid, shares purchased and net income involving the five major companies. In addition, we study the evolution of oil prices, and its influence in several items of the financial statements. Even though oil prices were at high levels during 2011-2014, however, the net income of the five companies actually declined due to the impact of peak oil. Finally, data for the last year studied (2015 indicate a general deterioration in return ratios and other accounting variables. Although the new investments should have been profitable, they have been influenced by peak oil, compromising the economic position of the companies. The advice to these companies would be to relax their investments, especially during a period of falling oil prices. Company managers need to recognize the prolonged duration of peak oil and price trends to promote profitability recovery decisions.

Heavy oils clean up

International Nuclear Information System (INIS)

Collitt, R.

1997-01-01

High production, transport and refining costs have long led oil companies to shun heavy crude oils. Advances in the technology of upgrading heavy oils, however, are likely to reduce transport costs and improve the refinery output. Research and development by Venezuela's state oil company, Petroleos de Venezuela (PDVSA), has resulted in a process called Aquaconversion which permits the upgrading of heavy crude oils using a catalyst and the hydrogen from steam. This may be carried out at the wellhead in small low-pressure and relatively inexpensive units. In addition, higher distillate yields of higher value could be produced by revamping the thermal cracking units of refineries to incorporate the new technology. This has generated considerable interest in Venezuela's large extra-heavy crude oil reserves and has led multinational oil companies along with PDVSA to pledge $17 billion to their development. Even at a $2 to $3 per barrel upgrading cost, Venezuela's extra heavy crudes are competitive with lighter oils from other countries. Other major markets for the new technology are likely to be China and Russia, given their own large heavy crude reserves. (UK)

Antimicrobial activity and mechanisms of Salvia sclarea essential oil.

Science.gov (United States)

Cui, Haiying; Zhang, Xuejing; Zhou, Hui; Zhao, Chengting; Lin, Lin

2015-12-01

Nowadays, essential oils are recognized as safe substances and can be used as antibacterial additives. Salvia sclarea is one of the most important aromatic plants cultivated world-wide as a source of essential oils. In addition to being flavoring foods, Salvia sclarea essential oil can also act as antimicrobials and preservatives against food spoilage. Understanding more about the antibacterial performance and possible mechanism of Salvia sclarea essential oil will be helpful for its application in the future. But so far few related researches have been reported. In our study, Salvia sclarea oil showed obvious antibacterial activity against all tested bacterial strains. Minimum inhibitory concentration (MIC) and minimum bactericide concentration (MBC) of seven pathogens were 0.05 and 0.1 % respectively. In addition, Salvia sclarea oil also exhibited a significant inhibitory effect on the growth of Escherichia coli (E. coli) in phosphate buffer saline (PBS) and meats. After treated with Salvia sclarea oil, Scanning Electron Microscope (SEM) images can clearly see the damage of cell membrane; the intracellular ATP concentrations of E. coli and S. aureus reduced 98.27 and 69.61 % respectively, compared to the control groups; the nuclear DNA content of E. coli and S. aureus was significantly reduced to 48.32 and 50.77 % respectively. In addition, there was massive leakage of cellular material when E. coli and S. aureus were exposed to Salvia sclarea oil. Salvia sclarea essential oil damaged the cell membrane and changed the cell membrane permeability, leading to the release of some cytoplasm such as macromolecular substances, ATP and DNA. In general, the antimicrobial action of Salvia sclarea essential oil is not only attributable to a unique pathway, but also involves a series of events both on the cell surface and within the cytoplasm. Therefore, more experiments need to be done to fully understand the antimicrobial mechanism of Salvia sclarea essential oil.

Castor Oil-Based Biodegradable Polyesters.

Science.gov (United States)

Kunduru, Konda Reddy; Basu, Arijit; Haim Zada, Moran; Domb, Abraham J

2015-09-14

This Review compiles the synthesis, physical properties, and biomedical applications for the polyesters based on castor oil and ricinoleic acid. Castor oil has been known for its medicinal value since ancient times. It contains ∼90% ricinoleic acid, which enables direct chemical transformation into polyesters without interference of other fatty acids. The presence of ricinoleic acid (hydroxyl containing fatty acid) enables synthesis of various polyester/anhydrides. In addition, castor oil contains a cis-double bond that can be hydrogenated, oxidized, halogenated, and polymerized. Castor oil is obtained pure in large quantities from natural sources; it is safe and biocompatible.

Oil price uncertainty in Canada

Energy Technology Data Exchange (ETDEWEB)

Elder, John [Department of Finance and Real Estate, 1272 Campus Delivery, Colorado State University, Fort Collins, CO 80523 (United States); Serletis, Apostolos [Department of Economics, University of Calgary, Calgary, Alberta (Canada)

2009-11-15

Bernanke [Bernanke, Ben S. Irreversibility, uncertainty, and cyclical investment. Quarterly Journal of Economics 98 (1983), 85-106.] shows how uncertainty about energy prices may induce optimizing firms to postpone investment decisions, thereby leading to a decline in aggregate output. Elder and Serletis [Elder, John and Serletis, Apostolos. Oil price uncertainty.] find empirical evidence that uncertainty about oil prices has tended to depress investment in the United States. In this paper we assess the robustness of these results by investigating the effects of oil price uncertainty in Canada. Our results are remarkably similar to existing results for the United States, providing additional evidence that uncertainty about oil prices may provide another explanation for why the sharp oil price declines of 1985 failed to produce rapid output growth. Impulse-response analysis suggests that uncertainty about oil prices may tend to reinforce the negative response of output to positive oil shocks. (author)

Addition of Ca-soap of Sardinella longiceps oil into the ration: 2. Its effect on physical and chemical characteristics of lamb

Directory of Open Access Journals (Sweden)

A Sudarman

2008-06-01

Full Text Available Lamb contains high saturated fatty acids and cholesterol. Consuming such meat tends to increase atherosclerosis incident. Fat content and composition of meat might be manipulated by giving lemuru fish oil which is rich in HDL and unsaturated fatty acids into sheep diet. Giving lemuru fish oil in the protected form, such as complex calcium-soap is believed to be more beneficial. Twelve sheep were distributed into four groups to receive four experimental diets in studying the influence of calcium soap on meat quality. The sheep were allocated based on Randomized Block Design and at the end of rearing period they were slaughtered. The experimental diets were: R0 = control diet, R1 = R0 + 1.5% calcium soap, R2 = R0 + 3% calcium soap and R3 = R0 + 4.5% calcium soap. Data were analyzed using analysis of variance and any significant differences were further tested using contrast orthogonal. The results showed that the treatments significantly (P<0.01 reduced fat content, both of low density lipoprotein cholesterol (LDL, and high density lipoprotein cholesterol (HDL of sheep meat. There were no differences in tendernes, cooking loss, water holding capacity (WHC and pH of meat. It is concluded that the best level of Ca-soap fish oil addition to yield healthy meat is 3%.

Getting Over the Barrel- Achieving Independence from Foreign Oil in 2018

National Research Council Canada - National Science Library

Haigh, Christopher S

2009-01-01

The United States can achieve independence from foreign oil in 2018. Increasing production from current oil fields, developing untapped oil resources, converting coal to oil and oil shale extraction can produce an additional...

21 CFR 173.275 - Hydrogenated sperm oil.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Hydrogenated sperm oil. 173.275 Section 173.275... CONSUMPTION Solvents, Lubricants, Release Agents and Related Substances § 173.275 Hydrogenated sperm oil. The food additive hydrogenated sperm oil may be safely used in accordance with the following prescribed...

Coconut oil extraction by the traditional Java method : An investigation of its potential application in aqueous Jatropha oil extraction

NARCIS (Netherlands)

Marasabessy, Ahmad; Moeis, Maelita R.; Sanders, Johan P. M.; Weusthuis, Ruud A.

A traditional Java method of coconut oil extraction assisted by paddy crabs was investigated to find out if crabs or crab-derived components can be used to extract oil from Jatropha curcas seed kernels. Using the traditional Java method the addition of crab paste liberated 54% w w(-1) oil from

[Determination of the Plant Origin of Licorice Oil Extract, a Natural Food Additive, by Principal Component Analysis Based on Chemical Components].

Science.gov (United States)

Tada, Atsuko; Ishizuki, Kyoko; Sugimoto, Naoki; Yoshimatsu, Kayo; Kawahara, Nobuo; Suematsu, Takako; Arifuku, Kazunori; Fukai, Toshio; Tamura, Yukiyoshi; Ohtsuki, Takashi; Tahara, Maiko; Yamazaki, Takeshi; Akiyama, Hiroshi

2015-01-01

"Licorice oil extract" (LOE) (antioxidant agent) is described in the notice of Japanese food additive regulations as a material obtained from the roots and/or rhizomes of Glycyrrhiza uralensis, G. inflata or G. glabra. In this study, we aimed to identify the original Glycyrrhiza species of eight food additive products using LC/MS. Glabridin, a characteristic compound in G. glabra, was specifically detected in seven products, and licochalcone A, a characteristic compound in G. inflata, was detected in one product. In addition, Principal Component Analysis (PCA) (a kind of multivariate analysis) using the data of LC/MS or (1)H-NMR analysis was performed. The data of thirty-one samples, including LOE products used as food additives, ethanol extracts of various Glycyrrhiza species and commercially available Glycyrrhiza species-derived products were assessed. Based on the PCA results, the majority of LOE products was confirmed to be derived from G. glabra. This study suggests that PCA using (1)H-NMR analysis data is a simple and useful method to identify the plant species of origin of natural food additive products.

Research advancements in palm oil nutrition*

Science.gov (United States)

May, Choo Yuen; Nesaretnam, Kalanithi

2014-01-01

Palm oil is the major oil produced, with annual world production in excess of 50 million tonnes. About 85% of global palm oil produced is used in food applications. Over the past three decades, research on nutritional benefits of palm oil have demonstrated the nutritional adequacy of palm oil and its products, and have resulted in transitions in the understanding these attributes. Numerous studies have demonstrated that palm oil was similar to unsaturated oils with regards to effects on blood lipids. Palm oil provides a healthy alternative to trans-fatty acid containing hydrogenated fats that have been demonstrated to have serious deleterious effects on health. The similar effects of palm oil on blood lipids, comparable to other vegetable oils could very well be due to the structure of the major triglycerides in palm oil, which has an unsaturated fatty acid in the stereospecific numbers (sn)-2 position of the glycerol backbone. In addition, palm oil is well endowed with a bouquet of phytonutrients beneficial to health, such as tocotrienols, carotenoids, and phytosterols. This review will provide an overview of studies that have established palm oil as a balanced and nutritious oil. PMID:25821404

Research advancements in palm oil nutrition.

Science.gov (United States)

May, Choo Yuen; Nesaretnam, Kalanithi

2014-10-01

Palm oil is the major oil produced, with annual world production in excess of 50 million tonnes. About 85% of global palm oil produced is used in food applications. Over the past three decades, research on nutritional benefits of palm oil have demonstrated the nutritional adequacy of palm oil and its products, and have resulted in transitions in the understanding these attributes. Numerous studies have demonstrated that palm oil was similar to unsaturated oils with regards to effects on blood lipids. Palm oil provides a healthy alternative to trans-fatty acid containing hydrogenated fats that have been demonstrated to have serious deleterious effects on health. The similar effects of palm oil on blood lipids, comparable to other vegetable oils could very well be due to the structure of the major triglycerides in palm oil, which has an unsaturated fatty acid in the stereospecific numbers ( sn) -2 position of the glycerol backbone. In addition, palm oil is well endowed with a bouquet of phytonutrients beneficial to health, such as tocotrienols, carotenoids, and phytosterols. This review will provide an overview of studies that have established palm oil as a balanced and nutritious oil.

Impact of Oil on Bacterial Community Structure in Bioturbated Sediments

Science.gov (United States)

Stauffert, Magalie; Cravo-Laureau, Cristiana; Jézéquel, Ronan; Barantal, Sandra; Cuny, Philippe; Gilbert, Franck; Cagnon, Christine; Militon, Cécile; Amouroux, David; Mahdaoui, Fatima; Bouyssiere, Brice; Stora, Georges; Merlin, François-Xavier; Duran, Robert

2013-01-01

Oil spills threaten coastlines where biological processes supply essential ecosystem services. Therefore, it is crucial to understand how oil influences the microbial communities in sediments that play key roles in ecosystem functioning. Ecosystems such as sediments are characterized by intensive bioturbation due to burrowing macrofauna that may modify the microbial metabolisms. It is thus essential to consider the bioturbation when determining the impact of oil on microbial communities. In this study, an experimental laboratory device maintaining pristine collected mudflat sediments in microcosms closer to true environmental conditions – with tidal cycles and natural seawater – was used to simulate an oil spill under bioturbation conditions. Different conditions were applied to the microcosms including an addition of: standardized oil (Blend Arabian Light crude oil, 25.6 mg.g−1 wet sediment), the common burrowing organism Hediste (Nereis) diversicolor and both the oil and H. diversicolor. The addition of H. diversicolor and its associated bioturbation did not affect the removal of petroleum hydrocarbons. After 270 days, 60% of hydrocarbons had been removed in all microcosms irrespective of the H. diversicolor addition. However, 16S-rRNA gene and 16S-cDNA T-RFLP and RT-PCR-amplicon libraries analysis showed an effect of the condition on the bacterial community structure, composition, and dynamics, supported by PerMANOVA analysis. The 16S-cDNA libraries from microcosms where H. diversicolor was added (oiled and un-oiled) showed a marked dominance of sequences related to Gammaproteobacteria. However, in the oiled-library sequences associated to Deltaproteobacteria and Bacteroidetes were also highly represented. The 16S-cDNA libraries from oiled-microcosms (with and without H. diversicolor addition) revealed two distinct microbial communities characterized by different phylotypes associated to known hydrocarbonoclastic bacteria and dominated by

Impact of oil on bacterial community structure in bioturbated sediments.

Directory of Open Access Journals (Sweden)

Magalie Stauffert

Full Text Available Oil spills threaten coastlines where biological processes supply essential ecosystem services. Therefore, it is crucial to understand how oil influences the microbial communities in sediments that play key roles in ecosystem functioning. Ecosystems such as sediments are characterized by intensive bioturbation due to burrowing macrofauna that may modify the microbial metabolisms. It is thus essential to consider the bioturbation when determining the impact of oil on microbial communities. In this study, an experimental laboratory device maintaining pristine collected mudflat sediments in microcosms closer to true environmental conditions--with tidal cycles and natural seawater--was used to simulate an oil spill under bioturbation conditions. Different conditions were applied to the microcosms including an addition of: standardized oil (Blend Arabian Light crude oil, 25.6 mg.g⁻¹ wet sediment, the common burrowing organism Hediste (Nereis diversicolor and both the oil and H. diversicolor. The addition of H. diversicolor and its associated bioturbation did not affect the removal of petroleum hydrocarbons. After 270 days, 60% of hydrocarbons had been removed in all microcosms irrespective of the H. diversicolor addition. However, 16S-rRNA gene and 16S-cDNA T-RFLP and RT-PCR-amplicon libraries analysis showed an effect of the condition on the bacterial community structure, composition, and dynamics, supported by PerMANOVA analysis. The 16S-cDNA libraries from microcosms where H. diversicolor was added (oiled and un-oiled showed a marked dominance of sequences related to Gammaproteobacteria. However, in the oiled-library sequences associated to Deltaproteobacteria and Bacteroidetes were also highly represented. The 16S-cDNA libraries from oiled-microcosms (with and without H. diversicolor addition revealed two distinct microbial communities characterized by different phylotypes associated to known hydrocarbonoclastic bacteria and dominated by

Analytical Characterization of Butter Oil Enriched with Omega-3 and 6 Fatty Acid Sthrough Chia (Salvia hispanica L.) Seed Oil

OpenAIRE

Muhammad Nadeem; Muhammad Ajmal; Fazal Rahman; Muhammad Ayaz

2015-01-01

Analytical characterization of blends of butter oil and chia (Salvia hispanica L.) seed oil was performed. Chia oil was added in butter oil at four different levels i.e. 6.25%, 12.5%, 18.75% and 25% (T1, T2, T3 and T4), butter oil without any addition of chia oil served as control. Blends of butter oil and chia oil were packaged in tin containers, stored at ambient temperature (34±2oC) for 90-days. Iodine values of control, T1, T2, T3 and T4 were 36.85, 45.63, 57.22, 67.45 and 76.37 (cg/g).Co...

PENINGKATAN KADAR GERANIOL DALAM MINYAK SEREH WANGI DAN APLIKASINYA SEBAGAI BIO ADDITIVE GASOLINE

Directory of Open Access Journals (Sweden)

Widi Astuti

2014-10-01

Full Text Available Sereh wangi merupakan salah satu tanaman penghasil minyak atsiri yang banyak mengandung geraniol. Geraniol merupakan senyawa penyedia oksigen sehingga minyak sereh wangi dimungkinkan dapat digunakan sebagai bio additive gasoline. Penelitian ini bertujuan  meningkatkan kadar geraniol dalam minyak sereh wangi dan menggunakannya sebagai bio additive gasoline.Penelitian dilakukan dalam  tiga tahap, yaitu  pemungutan minyak sereh wangi dari daun sereh wangi, peningkatan kadar geraniol dalam minyak sereh wangi dan aplikasi minyak sereh wangi yang mengandung geraniol tinggi sebagai bio aditive gasoline.Hasil penelitian menunjukkan bahwa pemungutan minyak sereh wangi yang dilakukan dengan metode distilasi uap menghasilkan rendemen sebesar 0,76% dengan kadar geraniol 5,36%.Kadar geraniol dapat ditingkatkan menjadi 21,78% melalui proses distilasi vakum pada suhu 120oC. Pengujian minyak sereh wangi dengan kadar geraniol tinggi sebagai bio additive gasoline meliputi uji performa dan efisiensi konsumsi bahan bakar dengan variasi perbandingan volume gasoline dengan bio additive. Hasilnya, penambahan minyak sereh wangi dengan perbandingan volume gasoline ; minyak sereh wangi = 1000:2 mampu meningkatkan power mesin dari 7,8HP menjadi 8,6HP. Sementara, pada pengujian efisiensi bahan bakar, penambahan minyak sereh wangi dengan perbandingan volume gasoline : minyak sereh wangi = 1000:2 dapat meningkatkan efisiensi mesin sebesar 10,8%. Citronella contains geraniol which is an oxygen provider substances, so it may be used as bio additive. The purpose of this research  is to increase geraniol content in citronella oil and use it as a gasoline bio additive. This research is conducted  in three steps including take the citronella oil from citronella leaf, increase geraniol content in citronella oil and use citronella oil as a gasoline bio additive. The result show that citronella oil produced from citronella leaf using vapor distillation method contains geraniol

Horizontal well impact on heavy oil supply

International Nuclear Information System (INIS)

Bowers, B.; Bielecki, J.; Hu, J.; Wall, B.; Drummond, K.

1993-01-01

Horizontal wells can take advantage of gravity drainage mechanisms, which can be important in conventional heavy oil and bitumen recovery. Horizontal drilling will impact on the development of established conventional heavy oil pools by infill drilling and application of enhanced recovery techniques. There will also be an impact on the development of extensions to established and newly discovered heavy oil pools, as well as a major impact on development of bitumen resources. To assess the impact of horizontal drilling on heavy oil supply, high-impact and low-impact scenarios were evaluated under specified oil-price assumptions for four heavy oil areas in Saskatchewan and Alberta. Horizontal well potential for infill drilling, waterflood projects, and thermal projects was assessed and estimates were made of such developments as reserves additions and heavy oil development wells under the two scenarios. In the low case, projected supply of conventional heavy oil and bitumen stabilizes at a level in the 90,000-94,000 m 3 /d after 1994. In the high case, overall supply continuously grows from 80,000 m 3 /d in 1992 to 140,000 m 3 /d in 2002. Through application of horizontal drilling, reserves additions in western Canada could be improved by ca 100 million m 3 by 2002. 14 figs., 6 tabs

Determination of vegetable oils and fats adulterants in diesel oil by high performance liquid chromatography and multivariate methods.

Science.gov (United States)

Brandão, Luiz Filipe Paiva; Braga, Jez Willian Batista; Suarez, Paulo Anselmo Ziani

2012-02-17

The current legislation requires the mandatory addition of biodiesel to all Brazilian road diesel oil A (pure diesel) marketed in the country and bans the addition of vegetable oils for this type of diesel. However, cases of irregular addition of vegetable oils directly to the diesel oil may occur, mainly due to the lower cost of these raw materials compared to the final product, biodiesel. In Brazil, the situation is even more critical once the country is one of the largest producers of oleaginous products in the world, especially soybean, and also it has an extensive road network dependent on diesel. Therefore, alternatives to control the quality of diesel have become increasingly necessary. This study proposes an analytical methodology for quality control of diesel with intention to identify and determine adulterations of oils and even fats of vegetable origin. This methodology is based on detection, identification and quantification of triacylglycerols on diesel (main constituents of vegetable oils and fats) by high performance liquid chromatography in reversed phase with UV detection at 205nm associated with multivariate methods. Six different types of oils and fats were studied (soybean, frying oil, corn, cotton, palm oil and babassu) and two methods were developed for data analysis. The first one, based on principal component analysis (PCA), nearest neighbor classification (KNN) and univariate regression, was used for samples adulterated with a single type of oil or fat. In the second method, partial least square regression (PLS) was used for the cases where the adulterants were mixtures of up to three types of oils or fats. In the first method, the techniques of PCA and KNN were correctly classified as 17 out of 18 validation samples on the type of oil or fat present. The concentrations estimated for adulterants showed good agreement with the reference values, with mean errors of prediction (RMSEP) ranging between 0.10 and 0.22% (v/v). The PLS method was

The comparative effects of oil dispersants and oil/dispersant conjugates on germination of the marine macroalga Phyllospora comosa (Fucales: Phaeophyta)

International Nuclear Information System (INIS)

Burridge, T.R.; Shir, M.-A.

1995-01-01

Germination inhibition of the marine macrophyte Phyllospora comosa was utilized as a sub-lethal end-point to assess and compare the effects of four oil dispersants and dispersed diesel fuel and crude oil combinations. Inhibition of germination by the water-soluble fraction of diesel fuel increased following the addition of each of the dispersants; the nominal 48-h EC 50 concentration of diesel fuel declined from 6800 to approximately 400 μl 1 -1 nominal for each dispersed combination. This contrasted with crude oil, where the addition of two dispersants resulted in an enhanced germination rate and an increase in nominal EC 50 concentrations from 130 μl 1 -1 for the undispersed crude to 4000 and 2500 μl 1 -1 . The results indicate that, while germination inhibition of P. comosa may be enhanced by the chemical dispersal of oil response varies with type of both oil and oil dispersant. (author)

An Open-label Randomized Controlled Trial to Compare Weight Gain of Very Low Birth Weight Babies with or without Addition of Coconut Oil to Breast Milk.

Science.gov (United States)

Arun, Sumitha; Kumar, Manish; Paul, Thomas; Thomas, Nihal; Mathai, Sarah; Rebekah, Grace; Thomas, Niranjan

2018-03-23

Nutritional guidelines involving the feeding of very low birth weight babies (VLBW) recommend addition of Human Milk Fortifiers to breast milk. Owing to financial constraints, it is a practice in low- and middle-income countries (LMIC) to add coconut oil to aid better weight gain. There are inadequate data on improvement of growth parameters with oral coconut oil supplementation of breast milk. In this randomized controlled trial, we measured growth parameters and body composition of 60 babies who received either breast milk with coconut oil or breast milk alone. Randomization was stratified according to intrauterine growth appropriate for gestational age (n = 30) and small for gestational age (n = 30). There was no difference in weight gain between the two groups. The weight gain velocity was 15 ± 3.6 and 14.4 ± 3.4 g/kg/day (p value = 0.49) in the breast milk alone and in the breast milk with coconut oil group, respectively. There was no difference in increase in head circumference and length. Triceps skinfold thickness (n = 56) was similar in both groups, but subscapular skinfold thickness was significantly more in the coconut oil group. Total body fat percentage did not differ between the groups (25.2 ± 4.3 vs. 25.5 ± 4.3%, p = 0.79). Oral supplementation of coconut oil along with breast milk did not increase growth parameters or result in change in body composition in very low birth weight (VLBW) babies.

Utah Heavy Oil Program

Energy Technology Data Exchange (ETDEWEB)

J. Bauman; S. Burian; M. Deo; E. Eddings; R. Gani; R. Goel; C.K. Huang; M. Hogue; R. Keiter; L. Li; J. Ruple; T. Ring; P. Rose; M. Skliar; P.J. Smith; J.P. Spinti; P. Tiwari; J. Wilkey; K. Uchitel

2009-10-20

The Utah Heavy Oil Program (UHOP) was established in June 2006 to provide multidisciplinary research support to federal and state constituents for addressing the wide-ranging issues surrounding the creation of an industry for unconventional oil production in the United States. Additionally, UHOP was to serve as an on-going source of unbiased information to the nation surrounding technical, economic, legal and environmental aspects of developing heavy oil, oil sands, and oil shale resources. UHOP fulGilled its role by completing three tasks. First, in response to the Energy Policy Act of 2005 Section 369(p), UHOP published an update report to the 1987 technical and economic assessment of domestic heavy oil resources that was prepared by the Interstate Oil and Gas Compact Commission. The UHOP report, entitled 'A Technical, Economic, and Legal Assessment of North American Heavy Oil, Oil Sands, and Oil Shale Resources' was published in electronic and hard copy form in October 2007. Second, UHOP developed of a comprehensive, publicly accessible online repository of unconventional oil resources in North America based on the DSpace software platform. An interactive map was also developed as a source of geospatial information and as a means to interact with the repository from a geospatial setting. All documents uploaded to the repository are fully searchable by author, title, and keywords. Third, UHOP sponsored Give research projects related to unconventional fuels development. Two projects looked at issues associated with oil shale production, including oil shale pyrolysis kinetics, resource heterogeneity, and reservoir simulation. One project evaluated in situ production from Utah oil sands. Another project focused on water availability and produced water treatments. The last project considered commercial oil shale leasing from a policy, environmental, and economic perspective.

Nutrient demand in bioventing of fuel oil pollution

International Nuclear Information System (INIS)

Breedveld, G.D.; Hauge, A.; Olstad, G.

1995-01-01

The effect of nutrient addition on bioventing of fuel oil pollution in an artificially polluted sandy soil has been studied at different experimental scales to assess the predictive value of laboratory treatability studies. The results of batch studies, laboratory column studies, and pilot-scale field tests (10 tons of soil) were compared. The qualitative response to nutrient addition was comparable in all experiments. Without nutrient addition, a minimal respiration rate was observed. With nutrient addition, respiration rates increased almost instantaneously. The highest rates were observed in the batch studies. The column study and pilot-scale field test indicated similar respiration rates, at approximately one sixth the respiration rates in the batch study. Respiration rates in the pilot-scale field study decreased during the winter season. Analysis of the residual oil composition in soil samples showed a relation between the degree of weathering, measured as the n-C 17 /pristane and n-C 18 /phytane ratio, and nutrient addition. Lower n-C 17 /pristane ratios were observed at higher total nitrogen content. After 1 year of bioventing with nutrient addition, a 66% reduction in TPH content was observed. Without nutrient addition, the residual oil still closely resembled the original fuel oil product, with only minor removal of the light-end compounds

Environmentally adjusted oil and grease

International Nuclear Information System (INIS)

Andersson, Bert; Lindberg, J.

1992-01-01

With the intention of maintaining healthy environment in our rivers Vattenfall in 1988 initiated a project called 'Environmentally friendly oils'. The goal was to find oils for bearings and hydraulic systems that would cause less negative environmental effects and still maintain a good technical function. Based on the results of the project it is recommended, for both economical and environmental reasons, to change to synthetic oil in bearings and to hydraulic oil made of white oil in regulating systems. The change may be carried out in connection to other work on the system in question. Special care is recommended when cleaning the system from old oil and dirt. In order to maintain the high quality of the oil, also during manufacturing and assembling, one should follow the recommendations outlined in the report. In bearings where used grease leaks into the river, a grease made of white oil should be used. The quality of the rubber sealings must be adapted to the oil used, in order to secure a good function. In order to bring down the number of products and to create an open market some additional changes is necessary in the specifications of oil. Further research regarding oil and sealing is planned. (3 refs.)

Method to upgrade bio-oils to fuel and bio-crude

Science.gov (United States)

Steele, Philip H; Pittman, Jr., Charles U; Ingram, Jr., Leonard L; Gajjela, Sanjeev; Zhang, Zhijun; Bhattacharya, Priyanka

2013-12-10

This invention relates to a method and device to produce esterified, olefinated/esterified, or thermochemolytic reacted bio-oils as fuels. The olefinated/esterified product may be utilized as a biocrude for input to a refinery, either alone or in combination with petroleum crude oils. The bio-oil esterification reaction is catalyzed by addition of alcohol and acid catalyst. The olefination/esterification reaction is catalyzed by addition of resin acid or other heterogeneous catalyst to catalyze olefins added to previously etherified bio-oil; the olefins and alcohol may also be simultaneously combined and catalyzed by addition of resin acid or other heterogeneous catalyst to produce the olefinated/esterified product.

Rheology of waxy oils

Energy Technology Data Exchange (ETDEWEB)

Alicke, Alexandra A.; Marchesini, Flavio H.; Mendes, Paulo R. de Souza [Pontificia Universidade Catolica do Rio de Janeiro (PUC-Rio), RJ (Brazil)], e-mails: fhmo@puc-rio.br, pmendes@puc-rio.br; Ziglio, Claudio [Petrobras Research Center, Rio de Janeiro, RJ (Brazil)], e-mail: ziglio@petrobras.com.br

2010-07-01

It is well known that below the crystallization temperature the rheology of waxy oils changes from Newtonian to an extremely complex non-Newtonian behavior, which is shear-rate and temperature-history dependent. Along the last decades a lot of effort has been put into obtaining reliable rheological measurements from different oils so as to understand the yielding of waxy oils as well as the effects of shear and temperature histories on rheological properties, such as viscosity, yield stress, storage and loss moduli. In this paper we examine in detail the related literature, discussing the main reasons for some disagreements concerning the history effects on the flow properties of waxy oils. In addition, we performed temperature ramps and stress-amplitude-sweep tests and compared the results obtained with the main trends observed, highlighting the effects of cooling and shear on the microstructure and consequently on the rheological properties of these oils. (author)

Co-processing of standard gas oil and biocrude oil to hydrocarbon fuels

International Nuclear Information System (INIS)

Agblevor, Foster A.; Mante, O.; McClung, R.; Oyama, S.T.

2012-01-01

The major obstacle in thermochemical biomass conversion to hydrocarbon fuels using pyrolysis has been the high oxygen content and the poor stability of the product oils, which cause them to solidify during secondary processing. We have developed a fractional catalytic pyrolysis process to convert biomass feedstocks into a product termed “biocrude oils” (stable biomass pyrolysis oils) which are distinct from unstable conventional pyrolysis oils. The biocrude oils are stable, low viscosity liquids that are storable at ambient conditions without any significant increases in viscosity; distillable at both atmospheric pressure and under vacuum without char or solid formation. About 15 wt% biocrude oils containing 20–25% oxygen were blended with 85 wt% standard gas oil and co-cracked in an Advanced Catalyst Evaluation (ACE™) unit using fluid catalytic cracking (FCC) catalysts to produce hydrocarbon fuels that contain negligible amount of oxygen. For the same conversion of 70% for both the standard gas oil and the biocrude oil/gas oil blends, the product gasoline yield was 44 wt%, light cycle oil (LCO) 17 wt%, heavy cycle oil (HCO) 13 wt%, and liquefied petroleum gas (LPG) 16 wt%. However, the coke yield for the standard gas oil was 7.06 wt% compared to 6.64–6.81 wt% for the blends. There appeared to be hydrogen transfer from the cracking of the standard gas oil to the biocrude oil which subsequently eliminated the oxygen in the fuel without external hydrogen addition. We have demonstrated for the first time that biomass pyrolysis oils can be successfully converted into hydrocarbons without hydrogenation pretreatment. -- Highlights: ► The co-processed product had less than 1% oxygen content and contained biocarbons determined by 14 C analysis. ► The co-processing did not affect the yields of gasoline, LCO, and HCO. ► First demonstration of direct conversion of pyrolysis oils into drop-in hydrocarbon fuels.

Effect of Addition of Soybean Oil and Gamma-Ray Cross-linking on the Nanoporous HDPE Membrane

Directory of Open Access Journals (Sweden)

Jong-Seok Park

2012-01-01

Full Text Available A nanoporous high-density polyethylene (HDPE membrane was prepared by a wet process. Soybean oil and dibutyl phthalate (DBP were premixed as codiluents, and gamma-rays were used for the cross-linking of HDPE. The pore volume of the nanoporous HDPE membranes with soybean oil was affected by the extracted amount of oil. The tensile strength of the membrane improved with an increasing absorbed dose up to 60 kGy, but decreased at 80 kGy due to severe degradation. The ionic conductivity of the nanoporous HDPE membrane did not really change with an increasing absorbed dose because the pores had already been formed before the gamma-ray radiation. Finally, the electrochemical stability of the HDPE membrane increased when the absorbed dose increased up to 60 kGy.

New oil and gas discoveries

International Nuclear Information System (INIS)

Alazard-Toux, N.

2004-01-01

During the period 1999-2003, new oil and gas fields generated additional reserves of nearly 11 000 bcm of natural gas and 62 Gbbl of oil and condensates, volumes very much superior to those discovered in the five previous years. Two-thirds of these discoveries were located offshore, half in deep water. (author)

Fuel saving performances of marine diesel engine oils on board

Energy Technology Data Exchange (ETDEWEB)

Hirose, Yasunori; Henmi, Takashi; Minamitani, Hiromu; Akizawa, Hayao; Hamada, Minoru; Ashida, Jiro

1988-05-01

After the second oil crisis, the percentage of the fuel cost against the operational cost of a ship has been showing the rising tendency, engine manufacturers have placed the top priority on the improvement of fuel consumption, operators have been conducting various energy saving measures and refiners have been paying efforts to improve lubricating oil. This article reports the study on the lubricating oil characteristics affecting the fuel consumption per power output, particularly the viscosity and the adding effect of friction modifier additives by using dynamo-generator diesel engines on board the ships already in commission. The investigation was conducted by comparing the cases of using several sample oils with the cases of using the reference oils. According to the results, the viscous property of engine oil was most effective on fuel consumption and the lower the viscosity of oil, the more the fuel consumption effect was. However, the addition of friction modifier additives did hardly show any improvement of the above effect. (5 figs, 4 tabs, 3 refs)

Jojoba oil and derivates

Energy Technology Data Exchange (ETDEWEB)

Wisniak, T

1977-01-01

Jojoba oil differs from all known seed oils by its almost complete absence of glycerides, making it more a liquid wax than a fat. It has become important as a possible substitute for sperm-whale oil to produce lubricants, lubricant additives and other products. The plant occurs naturally in southern Arizona and N.W. Mexico and its oil has long been used by Indians for medicinal, culinary, ritual and other purposes. It tolerates extreme daily fluctuations of temperature and grows well under the difficult soil and moisture conditions of the region. In the first part of this review the plant and its uses are described, including its floral, fruit and seed anatomy and the use of liquid wax during germination. Stored coryledon wax is used up by the embryo as a linear function of time during the first 30 days of germination and growth. Before germination, seeds weight about 0.59 mg and contain about 54% wax. The second and greater part of the review deals with jojoba oil (its extraction, properties, molecular description, toxicity and composition), jojoba meal, which remains after the oil has been extracted, and the chemical modification of the oil.

Purification of radioactive waste oil by a supercritical fluid

International Nuclear Information System (INIS)

Yoo, Jaeryong; Sung, Jinhyun; Park, Kwangheon; Kim, Hongdoo; Kim, Hakwon; Lim, Taeyoon; Yim, Sanghak; Yoon, Weonseob

2006-01-01

The radioactive waste oil from the nuclear industry is potentially hazardous due to its possibility to contaminate soil and underwater. Pollutants in waste oil are generally radioactive heavy metals or organo-metals. Radioactive waste oils are highly viscous fluids that are similar to used-motor oils. Several processes have been developed to regenerated used motor oil, such as acid clay treatment, chemical addition, vacuum distillation, thermal cracking and hydrofinishing. However, these technologies are difficult to apply to separating radioactive nuclides from radioactive waste oils. In recent years, our laboratory developed a membrane method for the regeneration of used motor oils. We applied supercritical Co2 (scCO2) as a viscosity reducing additive to waste oils at a lower process temperature in order to improve membrane permeability and thus the energy saving. However, the membrane cannot filter the contaminants in radioactive waste oil that are not particles, such as radioactive ions in impurity water in the oil. In this paper, we suggest a method extracting clean oil from the radioactive waste oil rather than filtering by a supercritical fluid. We selected R22, a refrigerant, as a solvent for extraction. R22 has a mild critical point - 96.1 .deg. and 49.9bar. Regeneration of waste oils by extracting clean oil using a supercritical fluid such as R22 is easy to handle and reduce secondary wastes. In this paper, we examine the feasibility of R22 in extracting clean oil from radioactive waste oils

Oxidative desulfurization of tire pyrolysis oil

OpenAIRE

Ahmad Shahzad; Ahmad Muhammad Imran; Naeem Khawar; Humayun Muhammad; Sebt-E-Zaeem; Faheem Farrukh

2016-01-01

This paper presents a low cost method for the purification of oils obtained from the pyrolysis of used tires. Oxidative desulfurization is a promising route for purification of tire pyrolysis oils as hydro-desulfurization may not be affordable for small scale industries. Different additives and acids have been employed for the enhancement of properties of pyrolytic oils. The experimental conditions were kept identical throughout, i.e. atmospheric pressure a...

Pacific Basin Heavy Oil Refining Capacity

Directory of Open Access Journals (Sweden)

David Hackett

2013-02-01

Full Text Available The United States today is Canada’s largest customer for oil and refined oil products. However, this relationship may be strained due to physical, economic and political influences. Pipeline capacity is approaching its limits; Canadian oil is selling at substantive discounts to world market prices; and U.S. demand for crude oil and finished products (such as gasoline, has begun to flatten significantly relative to historical rates. Lower demand, combined with increased shale oil production, means U.S. demand for Canadian oil is expected to continue to decline. Under these circumstances, gaining access to new markets such as those in the Asia-Pacific region is becoming more and more important for the Canadian economy. However, expanding pipeline capacity to the Pacific via the proposed Northern Gateway pipeline and the planned Trans Mountain pipeline expansion is only feasible when there is sufficient demand and processing capacity to support Canadian crude blends. Canadian heavy oil requires more refining and produces less valuable end products than other lighter and sweeter blends. Canadian producers must compete with lighter, sweeter oils from the Middle East, and elsewhere, for a place in the Pacific Basin refineries built to handle heavy crude blends. Canadian oil sands producers are currently expanding production capacity. Once complete, the Northern Gateway pipeline and the Trans Mountain expansion are expected to deliver an additional 500,000 to 1.1 million barrels a day to tankers on the Pacific coast. Through this survey of the capacity of Pacific Basin refineries, including existing and proposed facilities, we have concluded that there is sufficient technical capacity in the Pacific Basin to refine the additional Canadian volume; however, there may be some modifications required to certain refineries to allow them to process Western Canadian crude. Any additional capacity for Canadian oil would require refinery modifications or

Transesterification of jojoba oil, sunflower oil, neem oil, rocket seed oil and linseed oil by tin catalysts

International Nuclear Information System (INIS)

Shah, Mazloom; Tariq, Muhammad; Ali, Saqib; Guo, Qing-Xiang; Fu, Yao

2014-01-01

The methanolysis of jojoba oil has been studied in the presence of tin powder, dibutyltin diacetate (C 4 H 9 ) 2 Sn(OOCCH 3 ) 2 , dioctyltin diacetate (C 8 H 17 ) 2 Sn(OOCCH 3 ) 2 , dibutyltin oxide (C 4 H 9 ) 2 SnO, dioctyltin oxide (C 8 H 17 ) 2 SnO, diphenyltin oxide (C 6 H 5 ) 2 SnO, dibutyltin chloride dihydroxide (C 4 H 9 ) 2 Sn(OH) 2 Cl, butyltinhydroxide hydrate (C 4 H 9 )Sn(=O)OH.xH 2 O, Ni nanoparticles and Pd nanoparticles act as catalysts. Among these, 1 weight % of dibutyltin diacetate shows the maximum conversion. Then, methanolysis of sunflower oil, neem oil, rocket seed oil and linseed oil into methyl esters studied in the presence of 1% dibutyltin diacetate as a catalyst and was compared their percentage conversions. The experimental yield for the conversion of jojoba oil, sunflower oil, neem oil, rocket seed oil and linseed oil into biodiesel was found to be 71%, 51%, 50.78%, 40.90% and 39.66%, respectively. The experimental yield of the conversion of jojoba oil into methyl esters was found to be increased up to 96% by increasing reaction time, without emulsion formation. The synthesis of jojoba seed oil biodiesel (JSOB), soybean oil biodiesel (SOB), neem oil biodiesel (NOB), rocket seed oil biodiesel (RSOB) and linseed oil biodiesel (LSOB) was confirmed by NMR ( 1 H and 13 C) and FT-IR analyses of biodiesel. - Highlights: • Transesterification of jojoba oil into biodiesel by tin and nano catalysts. • 1 weight % dibutyltin diacetate showed highest yield at 60 °C. • Catalytic conversion comparison of five oils using dibutyltin diacetate • The experimental yield of the conversion of jojoba oil increased with time. • FT-IR and NMR ( 1 H and 13 C) characterization

Improving oxidative stability of liquid fish oil supplements for pets

DEFF Research Database (Denmark)

Thomsen, Birgitte Raagaard; Griinari, Mikko; Jacobsen, Charlotte

2017-01-01

oxidative stability to the same extent as 2000 ppm mixed tocopherols in Oxipres. Overall, oxidative stability of fish oil or fish oil + vegetable oil blends was improved the most by addition of 5000 ppm rosemary extract and 500 ppm mixed tocopherols. A commercial oil blend with composition optimized based...... of fish oil by adding vegetable oils, mixed tocopherols and rosemary extract, and to formulate a commercial product according to the results obtained. The formulated product was evaluated against commercial fish oil products. An initial screening for antioxidative effect was performed by using Oxipres...... equipment. The effect of antioxidant and vegetable oil blends was examined in oils stored at 30 and 40°C by measuring peroxide value, volatile compounds with GC-MS and tocopherol content. Addition of vegetable oil and rosemary extract at high level (4000–6000 ppm) plus 600 ppm of mixed tocopherols increased...

Influence of spike lavender (Lavandula latifolia Med.) essential oil in the quality, stability and composition of soybean oil during microwave heating.

Science.gov (United States)

Rodrigues, Nuno; Malheiro, Ricardo; Casal, Susana; Asensio-S-Manzanera, M Carmen; Bento, Albino; Pereira, José Alberto

2012-08-01

Lipids oxidation is one of the main factors leading to quality losses in foods. Its prevention or delay could be obtained by the addition of antioxidants. In this sense the present work intend to monitor the protective effects of Lavandula latifolia essential oil during soybean oil microwave heating. To achieve the proposed goal quality parameters (free acidity, peroxide value, specific coefficients of extinction and ΔK), fatty acids profile, tocopherols and tocotrienols composition, antioxidant activity and oxidative stability were evaluated in soybean oil with and without spike lavender essential oils (EO) submitted to different microwave heating exposure times (1, 3, 5, 10 and 15 min; 1000 Watt) with a standard domestic microwave equipment. Microwave heating induced severe quality and composition losses, mainly above 3 min of microwave heating, regardless the sample tested. However, spike lavender EO addition counteracts the oxidation comparatively to control oils, by presenting enhanced values in quality parameters. A higher protection in unsaturated fatty acids loss was also observed as well as a higher antioxidant activity and oxidative stability. The microwave heating effects were clearly different in the samples with essential oils addition, allowing discrimination from plain soybean oils by a principal component analysis, being also capable to discriminate the different heating times tested within each sample. Copyright © 2012 Elsevier Ltd. All rights reserved.

Synthesis of novel castor oil phosphonates

Science.gov (United States)

Castor oil has served as a versatile hydroxy fatty acid (HFA); its principle component, ricinoleic acid, can be isolated from castor oil and has been modified extensively for a number of applications. Additionally, phosphonates and their corresponding phosphonic acids are a functional moiety that ha...

Intensification of transferring the Kazakhstan high-congealed oil: challenges and advances

Energy Technology Data Exchange (ETDEWEB)

Maimakov, Tayhan P.; Boiko, Galinal; Lyubchenko, Nina P. [High education institute «UNAT», Almaty (Kazakhstan); Shaihutdinov, Yerengaip M. [Kazakh national technical university, Almaty (Kazakhstan)

2008-07-01

It were investigated the rheohgica! parameters of South-Turgay region crude oils at presence of novel pour point depressant additive DP-43/2005. It has shown that additive improves pour point and rheohgica; properties of crude oil mixture Kumkol-Akshabidak, inhibits wax deposition and can provide safe conditions of crude oil mixture transportation through pipeline at the cold season of year. Keywords: oil, temperature of fluidity loss, rheology, viscosity, oligomer depressor dopants.

Radium in diesel oil

International Nuclear Information System (INIS)

Kulich, J.

1977-05-01

In order to determine the addition of radon and radium to the air in mines, originatiny from the combustion of petroleum, measurements of the content of radium in diesel oil have been performed. Knowing the radium content theradon content can easily be calculated. The procedures used for the chemical analysis of radium is desribed. The ash remaining after combustion of the diesel oil is soluted in water and radium is precipiated as sulphate. The radium is detected by a ZnS (Ag) detector. The diesel oils from different petroleum companies contained between o.019-0.5pCi radium - 226. The conclution is that the consumption of diesel oils in motors used in mines does not contribute to the radium - 226 content at the air move than permissible according to norms.(K.K.)

Effect of drying and co-matrix addition on the yield and quality of supercritical CO₂ extracted pumpkin (Cucurbita moschata Duch.) oil.

Science.gov (United States)

Durante, Miriana; Lenucci, Marcello S; D'Amico, Leone; Piro, Gabriella; Mita, Giovanni

2014-04-01

In this work a process for obtaining high vitamin E and carotenoid yields by supercritical carbon dioxide (SC-CO₂) extraction from pumpkin (Cucurbita moschata Duch.) is described. The results show that the use of a vacuum oven-dried [residual moisture (∼8%)] and milled (70 mesh sieve) pumpkin flesh matrix increased SC-CO₂ extraction yields of total vitamin E and carotenoids of ∼12.0- and ∼8.5-fold, respectively, with respect to the use of a freeze-dried and milled flesh matrix. The addition of milled (35 mesh) pumpkin seeds as co-matrix (1:1, w/w) allowed a further ∼1.6-fold increase in carotenoid yield, besides to a valuable enrichment of the extracted oil in vitamin E (274 mg/100 g oil) and polyunsaturated fatty acids. These findings encourage further studies in order to scale up the process for possible industrial production of high quality bioactive ingredients from pumpkin useful in functional food or cosmeceutical formulation. Copyright © 2013 Elsevier Ltd. All rights reserved.

Heavy oil : PetroChina's perspective

Energy Technology Data Exchange (ETDEWEB)

He, C. [PetroChina Co., Ltd., Beijing (China)

2010-07-01

This keynote presentation discussed China's future in relation to heavy oil refining. An overview of PetroChina's overseas operations was also presented. China currently has six 200,000 bpd refineries as well as an additional 12 refineries with a 100,000 bpd capacity that are able to process lower quality feedstocks with a high acid and sulphur content. Seven new 200,000 bpd refineries will be built by 2020. Poor and heavy crude oil from global heavy oil reserves will form a significant percentages of China's refinery feedstocks, and Canada is expected to provide a significant portion of its heavy oil and bitumen resources for further refining in China. China's existing refineries are being reconfigured and optimized for the processing of heavy crude oils. Additional hydrotreating and hydrocracking technologies have been added, and resid fluid catalytic cracking technologies have been retrofitted. China envisages a future with steady increases in oil consumption, high oil prices, and an increased reliance on heavy and poor quality crude oils. China's strong economic growth will increase demand for petrochemical feedstocks. Various research organizations and institutions have been established to accelerate innovation and technology development for ensuring that clean fuels standards are met. New refineries in China will include resid upgrading and new generation catalyst technologies. Details of various technologies were included. tabs., figs.

Eco-Friendly Multipurpose Lubricating Greases from Vegetable Residual Oils

Directory of Open Access Journals (Sweden)

Ponnekanti Nagendramma

2015-10-01

Full Text Available Environmentally friendly multipurpose grease formulation has been synthesized by using Jatropha vegetable residual oil with lithium soap and multifunctional additive. The thus obtained formulation was evaluated for its tribological performance on a four-ball tribo-tester. The anti-friction and anti-wear performance characteristics were evaluated using standard test methods. The biodegradability and toxicity of the base oil was assessed. The results indicate that the synthesized residual oil grease formulation shows superior tribological performance when compared to the commercial grease. On the basis of physico-chemical characterization and tribological performance the vegetable residual oil was found to have good potential for use as biodegradable multipurpose lubricating grease. In addition, the base oils are biodegradable and non toxic.

Treating oil in a maritime environment

International Nuclear Information System (INIS)

Seebacher, G.

2002-01-01

Some details of the International Maritime Organisation's marine pollution regulations are discussed. In simple terms, under IMO regulations oily water must be processed through approved equipment and can be legally discharged if the oil content in the treated effluent is less than 15 ppm. These regulations also make it clear that it is not permitted to use emulsifiers to hide the oil in the effluent. To separate the free oil from water, gravity enhanced separators can be used effectively. With conventional means it is possible to remove free oil from an oily water mixture, to the less than 15 part per million oil content. Conventional IMO certified oil content meters accurately read free oil content in the 0-30 ppm region, to prevent formation of an oil film from treated oily water discharges. Some additional basic rules of thumb worthy of consideration when separating oil from oily water: in general, it is cheaper to prevent oil discharge of oil into the effluent stream than to remove it; emulsifier-enriched lubricating oils emulsify readily and are difficult to remove when present in suspended droplets; the larger the amount of contamination, the greater the difficulty of removing the oil; an ounce of prevention is worth a pound of cure

Production of Detergent from Castor Oil

Directory of Open Access Journals (Sweden)

Abubakar Garba ISAH

2006-07-01

Full Text Available This research work was carried out with the objective of extraction of oil from castor seeds and its utilization to produce a synthetic detergent. Solvent extraction method was employed in extracting the oil and the total percent oil yield was found to be 23.8%. The experimentally determined saponification value of the oil was 183.7275mgKOH/g of oil. The detergent efficiency, determined as a measure of the foamability of the detergent was found to be 2.6cm. The pH tests revealed mildly basic properties. The color, scent and efficiency of the detergent were improved with the addition of bleaching agent, perfume and foaming agents respectively.

Vegetable oil based liquid nanocomposite dielectric

Directory of Open Access Journals (Sweden)

Leon Chetty

2013-01-01

Full Text Available Physically smaller dielectric materials would improve the optimisation of space for power systems. Development of nanotechnology provides an effective way to improve the performances of insulating oils used in power system applications. In this research study, we focused on the development of nanomodified vegetable oils to be used in power transformers. Higher conduction currents were observed in virgin linseed oil than in virgin castor oil. However, for both virgin linseed and virgin castor oil, the DC conduction current increased approximately linearly with the applied DC voltage. In nanomodified linseed oil, the characteristic curve showed two distinct regions: a linear region (at lower applied voltage and a saturation region (at slightly higher voltage. Conversely, in nanomodified castor oil, the characteristic curve showed three distinct regions: a linear region (at lower applied voltage, a saturation region (at intermediate applied voltage and an exponential growth region (at higher applied voltage. The nanomodified linseed oil exhibited a better dielectric performance than the nanomodified castor oil. Overall, the addition of nanodielectrics to vegetable oils decreased the dielectric performance of the vegetable oils. The results of this study contribute to the understanding of the pre-breakdown phenomenon in liquid nanocomposite dielectrics.

Conversion of Crude Oil to Methane by a Microbial Consortium Enriched From Oil Reservoir Production Waters

Directory of Open Access Journals (Sweden)

Carolina eBerdugo-Clavijo

2014-05-01

Full Text Available The methanogenic biodegradation of crude oil is an important process occurring in petroleum reservoirs and other oil-containing environments such as contaminated aquifers. In this process, syntrophic bacteria degrade hydrocarbon substrates to products such as acetate, and/or H2 and CO2 that are then used by methanogens to produce methane in a thermodynamically dependent manner. We enriched a methanogenic crude oil-degrading consortium from production waters sampled from a low temperature heavy oil reservoir. Alkylsuccinates indicative of fumarate addition to C5 and C6 n-alkanes were identified in the culture (above levels found in controls, corresponding to the detection of an alkyl succinate synthase gene (assA in the culture. In addition, the enrichment culture was tested for its ability to produce methane from residual oil in a sandstone-packed column system simulating a mature field. Methane production rates of up 5.8 μmol CH4/g of oil/day were measured in the column system. Amounts of produced methane were in relatively good agreement with hydrocarbon loss showing depletion of more than 50% of saturate and aromatic hydrocarbons. Microbial community analysis revealed that the enrichment culture was dominated by members of the genus Smithella, Methanosaeta, and Methanoculleus. However, a shift in microbial community occurred following incubation of the enrichment in the sandstone columns. Here, Methanobacterium sp. were most abundant, as were bacterial members of the genus Pseudomonas and other known biofilm forming organisms. Our findings show that microorganisms enriched from petroleum reservoir waters can bioconvert crude oil components to methane both planktonically and in sandstone-packed columns as test systems. Further, the results suggest that different organisms may contribute to oil biodegradation within different phases (e.g., planktonic versus sessile within a subsurface crude oil reservoir.

Biodegradability of northern crude oil

Energy Technology Data Exchange (ETDEWEB)

Cook, F D; Westlake, D W.S.

1976-01-01

Field studies on the microbiological degradation of crude oils encompassed the placing of oil-soaked plots in two areas in the Northwest Territories and Alberta. Replicate plots received amendments of fertilizer, oil-utilizing bacteria, fertilizer plus bacteria or were untreated except for the oil. Changes in microbial numbers and chemical composition of recovered oil were determined periodically. The initial stimulatory effect on bacterial numbers brought about by the addition of fertilizers to oil-soaked plots diminished two years after the application to a point where the differences were no longer significant. Experiments carried out in the Norman Wells area to determine the effect of the amount of fertilizer applied on oil degradation have yielded inconclusive results. The data suggest that at least 2.7 kg of urea-phosphate fertilizer per kl of oil is required to maintain a reasonable oil degradation rate. Preliminary studies on the use of fertilizer coated with chemicals to increase its hydrophobic character indicate that they could be useful in treating wet-land oil spills. Soils from the McKenzie River drainage basin indicate that bacteria are present which can use oil under mesophilic conditions. However, the ability to use the same oil under psychrophilic conditions is more restricted. At least one bacterial species from each mixed population studied was capable of bringing about chemical changes in oil similar to those observed for the original mixed culture. The potential hazards and uses of the seeding of oil spills is discussed relative to the environmental conditions found in the northern part of Canada. 35 refs., 2 figs., 15 tabs.

Evaluation of Sebostatic Activity of Juniperus communis Fruit Oil and Pelargonium graveolens Oil Compared to Niacinamide

Directory of Open Access Journals (Sweden)

Justyna Kozlowska

2017-09-01

Full Text Available As a facial skin condition, oily skin causes cosmetic problems, such as large pores, shiny appearance, and the feeling of greasiness and heaviness. Furthermore, extensive sebum production leads to common skin disorders such as acne vulgaris or seborrheic dermatitis. This study investigated the efficacy of sebum control tonics containing Juniperus communis fruit oil, Pelargonium graveolens oil, or niacinamide. The effects of Juniperus communis fruit oil, Pelargonium graveolens oil, and niacinamide on sebum excretion rates were investigated using Sebumeter®. Sebum measurements (Sebumeter® SM 815, Courage & Khazaka®, Köln, Germany were made on the skin surface in three places by applying the sebumeter probe to the forehead after 10, 60, and 120 min from application of the tonic. The results indicated that the application of the tonic maintained a lower sebum secretion 10 min and 60 min after the application of the cosmetic, compared to those before it. However, a visible sebum-reducing efficacy after 2 h was reported only for tonic containing 0.25% Pelargonium graveolens oil and for the tonic with the addition of 3% niacinamide. After 2 h, the values of sebum measurements were 44 ± 5.13 a.u. and 58 ± 9.07 a.u., respectively. Our results show that the tonic with the addition of 0.25% Pelargonium graveolens oil is the most effective in reducing sebum production.

Multiclass pesticide determination in olives and their processing factors in olive oil: comparison of different olive oil extraction systems.

Science.gov (United States)

Amvrazi, Elpiniki G; Albanis, Triantafyllos A

2008-07-23

The processing factors (pesticide concentration found in olive oil/pesticide concentration found in olives) of azinphos methyl, chlorpyrifos, lambda-cyhalothrin, deltamethrin, diazinon, dimethoate, endosulfan, and fenthion were determined in olive oil production process in various laboratory-scale olive oil extractions based on three- or two-phase centrifugation systems in comparison with samples collected during olive oil extractions in conventional olive mills located at different olive oil production areas in Greece. Pesticide analyses were performed using a multiresidue method developed in our laboratory for the determination of different insecticides and herbicides in olive oil by solid-phase extraction techniques coupled to gas chromatography detection (electron capture detection and nitrogen phosphorus detection), optimized, and validated for olive fruits sample preparation. Processing factors were found to vary among the different pesticides studied. Water addition in the oil extraction procedure (as in a three-phase centrifugation system) was found to decrease the processing factors of dimethoate, alpha-endosulfan, diazinon, and chlorpyrifos, whereas those of fenthion, azinphos methyl, beta-endosulfan, lambda-cyhalothrin, and deltamethrin residues were not affected. The water content of olives processed was found to proportionally affect pesticide processing factors. Fenthion sulfoxide and endosulfan sulfate were the major metabolites of fenthion and endosulfan, respectively, that were detected in laboratory-produced olive oils, but only the concentration of fenthion sulfoxide was found to increase with the increase of water addition in the olive oil extraction process.

Tough Blends of Polylactide and Castor Oil

Energy Technology Data Exchange (ETDEWEB)

Robertson, Megan L.; Paxton, Jessica M.; Hillmyer, Marc A. (UMM)

2012-10-10

Poly(l-lactide) (PLLA) is a renewable resource polymer derived from plant sugars with several commercial applications. Broader implementation of the material is limited due to its inherent brittleness. We show that the addition of 5 wt % castor oil to PLLA significantly enhances the overall tensile toughness with minimal reductions in the modulus and no plasticization of the PLLA matrix. In addition, we used poly(ricinoleic acid)-PLLA diblock copolymers, synthesized entirely from renewable resources, as compatibilizers for the PLLA/castor oil blends. Ricinoleic acid, the majority fatty acid comprising castor oil, was polymerized through a lipase-catalyzed condensation reaction. The resulting polymers contained a hydroxyl end-group that was subsequently used to initiate the ring-opening polymerization of L-lactide. The binary PLLA/castor oil blend exhibited a tensile toughness seven times greater than neat PLLA. The addition of block copolymer allowed for control over the morphology of the blends, and even further improvement in the tensile toughness was realized - an order of magnitude larger than that of neat PLLA.

Tough blends of polylactide and castor oil.

Science.gov (United States)

Robertson, Megan L; Paxton, Jessica M; Hillmyer, Marc A

2011-09-01

Poly(l-lactide) (PLLA) is a renewable resource polymer derived from plant sugars with several commercial applications. Broader implementation of the material is limited due to its inherent brittleness. We show that the addition of 5 wt % castor oil to PLLA significantly enhances the overall tensile toughness with minimal reductions in the modulus and no plasticization of the PLLA matrix. In addition, we used poly(ricinoleic acid)-PLLA diblock copolymers, synthesized entirely from renewable resources, as compatibilizers for the PLLA/castor oil blends. Ricinoleic acid, the majority fatty acid comprising castor oil, was polymerized through a lipase-catalyzed condensation reaction. The resulting polymers contained a hydroxyl end-group that was subsequently used to initiate the ring-opening polymerization of l-lactide. The binary PLLA/castor oil blend exhibited a tensile toughness seven times greater than neat PLLA. The addition of block copolymer allowed for control over the morphology of the blends, and even further improvement in the tensile toughness was realized-an order of magnitude larger than that of neat PLLA.

Hydrogenation upgrading of heavy oil residues

Energy Technology Data Exchange (ETDEWEB)

Krichko, A.A.; Maloletnev, A.S.; Mazneva, O.A.; Galkina, N.I. [Fossil Fuel Inst., Moscow (Russian Federation). Hydrogenation and Gasification Dept.; Suvorov, U.P.; Khadjiev, S.N. [Inst. Oil and Chemical Synthesis, Moscow (Russian Federation). Hydrogenation of Heavy Residues Dept.

1997-12-31

At present time in the world there is no simple and effective technology at low pressure (<15-20 MPa) which could give the opportunity to use oil residues for distillate fractions production. In Russia a process for hydrogenation (up 6 MPa hydrogen pressure) of high boiling point (b.p. >520 C) oil products, including high S, V and Ni contents ones, into distillates, feedstock for catalytic cracking (b.p. 360-520 C) and metal concentrates. The main point of the new process is as follows: the water solution of catalytic additive, for which purpose water soluble metal salts of VI-VIII groups are used, is mixed with heavy oil residues, dispersed and then subjected to additional supercavitation in a special apparatus. (orig.)

Bioremediation of offshore oil spills

International Nuclear Information System (INIS)

Goldman, E.; Tedaldi, D.J.

1994-01-01

This research program was directed towards the enhancement of insitu biorestoration of open sea oil spills. Bacteria possessing petroleum degrading enzymes are capable of splitting even thick, viscous oils and tars into lighter fractions. This process will occur at the oil/bacterial interface and depends upon viscosity of the oil, bacterial species, availability of ancillary nutrients, residence times and extent of mixing/oxygenation. Through the enzymatic metabolism of bacteria, a wide range of petroleum oils can be converted almost completely into CO 2 , water, cell mass and harmless biological waste products, usually within 60 to 90 days under favorable conditions. Specifically, this research work focused on the selection and examination of a floating medium which enhances the biodegradation process through improvement of conditions necessary for the process to occur. An additional effort was made to update previous citations of the order of magnitude of oil biodegradation rates and to compare laboratory measurements of biodegradation rates with field or mesocosm measurements

Additions of caffeic acid, ascorbyl palmitate or gamma-tocopherol to fish oil-enriched energy bars affect lipid oxidation differently

DEFF Research Database (Denmark)

Horn, Anna Frisenfeldt; Nielsen, Nina Skall; Jacobsen, Charlotte

2009-01-01

The objectives of the study were to investigate the effects of caffeic acid, ascorbyl palmitate and gamma-tocopherol on protection of fish oil-enriched energy bars against lipid oxidation during storage for 10 weeks at room temperature. The lipophilic gamma-tocopherol reduced lipid oxidation during...... storage when added at a concentration above 440 mu g/g fish oil. However, the best antioxidative effect was observed when it was added at a concentration of 660 mu g/g fish oil. In contrast, prooxidative effects were observed when using either gamma-tocopherol at concentrations below 220 mu g/g fish oil......, or the hydrophilic caffeic acid, or the amphiphilic ascorbyl palmitate at concentrations of 75, 150 and 300 mu g/g fish oil. Prooxidative effects were observed as an increase in the formation of lipid hydroperoxides and volatile secondary oxidation products, as well as the development of rancid off...

Oil refining expansion criteria for Brazil

International Nuclear Information System (INIS)

Tavares, M.E.E.; Szklo, A.S.; Machado, G.V.; Schaeffer, R.; Mariano, J.B.; Sala, J.F.

2006-01-01

This paper assesses different strategies for the expansion of Brazil's oil refining segment, using criteria that range from energy security (reducing imports and vulnerability for key products) through to maximizing the profitability of this sector (boosting the output of higher value oil products) and adding value to Brazil's oil production (reducing exports of heavy acid oil). The development prospects are analyzed for conventional fuel production technology routes, sketching out three possible refining schemes for Brazilian oil and a GTL plant for producing gasoil from natural gas. Market scenario simulations indicate that investments will be required in Brazil's oil refining segment over and above those allocated to planned modifications in its current facilities, reducing the nation's vulnerability in terms of gasoil and petrochemical naphtha imports. Although not economically attractive, oil refining is a key activity that is crucial to oil company strategies. The decision to invest in this segment depends on local infrastructure conditions, environmental constraints and fuel specifications, in addition to oil company strategies, steady growth in demand and the definition of a government policy that eases institutional risks. (author)

Oil refining expansion criteria for Brazil

International Nuclear Information System (INIS)

Tavares, Marina Elisabete Espinho; Szklo, Alexandre Salem; Machado, Giovani Vitoria; Schaeffer, Roberto; Mariano, Jacqueline Barboza; Sala, Janaina Francisco

2006-01-01

This paper assesses different strategies for the expansion of Brazil's oil refining segment, using criteria that range from energy security (reducing imports and vulnerability for key products) through to maximizing the profitability of this sector (boosting the output of higher value oil products) and adding value to Brazil's oil production (reducing exports of heavy acid oil). The development prospects are analyzed for conventional fuel production technology routes, sketching out three possible refining schemes for Brazilian oil and a GTL plant for producing gasoil from natural gas. Market scenario simulations indicate that investments will be required in Brazil's oil refining segment over and above those allocated to planned modifications in its current facilities, reducing the nation's vulnerability in terms of gasoil and petrochemical naphtha imports. Although not economically attractive, oil refining is a key activity that is crucial to oil company strategies. The decision to invest in this segment depends on local infrastructure conditions, environmental constraints and fuel specifications, in addition to oil company strategies, steady growth in demand and the definition of a government policy that eases institutional risks

Chemical, physical and tribological investigation of polymercaptanized soybean oil

Science.gov (United States)

Polymercaptanized soybean oil (PMSO) was investigated for its chemical, physical and tribological properties relative to soybean oil (SO) and also as a potential multi-functional lubricant additive in high oleic sunflower oil (HOSuO). Analytical investigations showed that PMSO is obtained by convers...

Producing carbon-based boundary films from catalytically active lubricant additives

Science.gov (United States)

Erdemir, Ali; Mane, Anil U.; Elam, Jeffrey W.; Ramirez, Giovanni; Eryilmaz, Osman

2018-04-24

A lubricant composition includes an oil including a plurality of long-chain hydrocarbon molecules. A quantity of a catalytically active metal-organic additive is mixed with the oil. The metal-organic additive is formulated to fragment the long-chain hydrocarbon molecules of the oil into at least one of dimers and trimers under the influence of at least one of a mechanical loading and a thermal loading. In some embodiments, the metal-organic additive includes a compound of formula II: ##STR00001## where: X is Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Y, Zr, Nb, Mo, Tc, Ru, Rh, Pd, Ag, Cd, Hf, Ta, W, Re, Os, Ir, Pt, Au, Hg, Rf, Db, Sg, Bh, Hs, Mt, Ds, Rg or Cn, and R.sub.1, R.sub.2, R.sub.3 and R.sub.4 are alkyl or alkyl halide.

Utilization of used oil. Final report

Energy Technology Data Exchange (ETDEWEB)

Mascetti, G.J.; White, H.M.

1978-08-01

This report assesses the potential impact of re-refining used automotive and industrial lubricating oils on the national petroleum consumption. The technical base for this assessment is derived from a comprehensive review of the processes utilized in re-refining used oil and those processes used to produce lube oil from crude. Both existing and recently proposed processes are considered. Additionally, an extensive review of processes described in the patent literature is provided. Re-refining processes are surveyed and evaluated. Process descriptions are provided; hardware is identified; and process energy and economic requirements are calculated. Factors affecting the profitability of a re-refining operation are discussed. Economic projections of the demand for lube oil and the ability to satisfy this demand from crude oil are made and the value of lube oil as a vital resource and the need for conservation are addressed. Other factors related to re-refining are discussed, including lube oil characteristics, degradation, lube oil quality and engine sequence testing, and legislative and institutional barriers. Finally, an energy assessment of used oil utilization is made. Two options are considered in this assessment: (1) all used oil is re-refined and recycled back to lube oil; (2) all used oil is burned to recover its heat content.

Effect of fast pyrolysis bio-oil from palm oil empty fruit bunch on bitumen properties

Science.gov (United States)

Poh, Chia Chin; Hassan, Norhidayah Abdul; Raman, Noor Azah Abdul; Shukry, Nurul Athma Mohd; Warid, Muhammad Naqiuddin Mohd; Satar, Mohd Khairul Idham Mohd; Ros Ismail, Che; Asmah Hassan, Sitti; Mashros, Nordiana

2018-04-01

Bitumen shortage has triggered the exploration of another alternative waste material that can be blended with conventional bitumen. This study presents the performance of pyrolysis bio-oil from palm oil empty fruit bunch (EFB) as an alternative binder in modified bitumen mixtures. The palm oil EFB was first pyrolyzed using auger pyrolyzer to extract the bio-oil. Conventional bitumen 80/100 penetration grade was used as a control sample and compared with samples that were modified with different percentages, i.e., 5% and 10%, of pyrolysis EFB bio-oil. The physical and rheological properties of the control and modified bitumen samples were investigated using penetration, softening point, viscosity and dynamic shear rheometer (DSR) tests. Results showed that the addition of EFB bio-oil softened the bitumen with high penetration and a reduction in softening point, penetration index, and viscosity. However, the DSR results showed a comparable rutting resistance between the bitumen samples containing EFB bio-oil and virgin bitumen with a failure temperature achieved greater than 64°C.

Interaction of Olive Oil and Metals

OpenAIRE

BÜYÜKGÖK, Elif Burçin; ÖTLEŞ, Semih

2011-01-01

Olive oil, obtained only from the fruits of olive trees, is a food item consumed in natural form without any chemical process and is liquid at room temperature. In addition to its flavor, oxidative stability is the unique property of it. Oxidative stability of olive oil is so powerful is due to its major components which are fatty acids and minor components which are phenolic compounds, tocopherols, squalene, sterols, phospholipids, carotenoids, chlorophyll, etc. All edible oils, including ol...

The spectral analysis of fuel oils using terahertz radiation and chemometric methods

Science.gov (United States)

Zhan, Honglei; Zhao, Kun; Zhao, Hui; Li, Qian; Zhu, Shouming; Xiao, Lizhi

2016-10-01

The combustion characteristics of fuel oils are closely related to both engine efficiency and pollutant emissions, and the analysis of oils and their additives is thus important. These oils and additives have been found to generate distinct responses to terahertz (THz) radiation as the result of various molecular vibrational modes. In the present work, THz spectroscopy was employed to identify a number of oils, including lubricants, gasoline and diesel, with different additives. The identities of dozens of these oils could be readily established using statistical models based on principal component analysis. The THz spectra of gasoline, diesel, sulfur and methyl methacrylate (MMA) were acquired and linear fittings were obtained. By using chemometric methods, including back propagation, artificial neural network and support vector machine techniques, typical concentrations of sulfur in gasoline (ppm-grade) could be detected, together with MMA in diesel below 0.5%. The absorption characteristics of the oil additives were also assessed using 2D correlation spectroscopy, and several hidden absorption peaks were discovered. The technique discussed herein should provide a useful new means of analyzing fuel oils with various additives and impurities in a non-destructive manner and therefore will be of benefit to the field of chemical detection and identification.

The spectral analysis of fuel oils using terahertz radiation and chemometric methods

International Nuclear Information System (INIS)

Zhan, Honglei; Zhao, Kun; Xiao, Lizhi; Zhao, Hui; Li, Qian; Zhu, Shouming

2016-01-01

The combustion characteristics of fuel oils are closely related to both engine efficiency and pollutant emissions, and the analysis of oils and their additives is thus important. These oils and additives have been found to generate distinct responses to terahertz (THz) radiation as the result of various molecular vibrational modes. In the present work, THz spectroscopy was employed to identify a number of oils, including lubricants, gasoline and diesel, with different additives. The identities of dozens of these oils could be readily established using statistical models based on principal component analysis. The THz spectra of gasoline, diesel, sulfur and methyl methacrylate (MMA) were acquired and linear fittings were obtained. By using chemometric methods, including back propagation, artificial neural network and support vector machine techniques, typical concentrations of sulfur in gasoline (ppm-grade) could be detected, together with MMA in diesel below 0.5%. The absorption characteristics of the oil additives were also assessed using 2D correlation spectroscopy, and several hidden absorption peaks were discovered. The technique discussed herein should provide a useful new means of analyzing fuel oils with various additives and impurities in a non-destructive manner and therefore will be of benefit to the field of chemical detection and identification. (paper)

Natural cold pressed oils as cosmetic products

Directory of Open Access Journals (Sweden)

Małgorzata Ligęza

2016-12-01

Full Text Available Background. It seems that patients may ask general practitioners about natural cosmetics applied on the skin regarding their safety and suitability. Objectives. The aim of the study was to analyze natural cold pressed oils as potential cosmetic products. Material and methods. Cold pressed oils obtained from selected seeds and fruit stones were analyzed, including: chokeberry seed oil, blackcurrant seed oil, elderberry seed oil, raspberry seed oil, apricot seed oil, tomato seed oil, strawberry seed oil, broccoli seed oil, Nigella sativa seed oil, hemp oil, safflower seed oil, Silybum marianum seed oil and coconut oil. 80 adult volunteers assessed the cosmetic properties of the analyzed oils. Each of the volunteers tested 2 to 4 different oils, by applying them on the skin. In addition, patch tests with all analyzed oils were performed on 23 individuals. Results. The majority of tested oils were positively evaluated by the participants: in the opinion of the participants, oil extracted from safflower had the best appearance (100% positive opinions, coconut oil had the best smell (70% positive opinions, while black currant seed oil showed the best absorbency (85% positive opinions. No irritation was observed within the analyzed product group, albeit one allergic reaction to apricot seed oil was observed with patch testing. Conclusions . Based on the achieved results, it could be suggested that natural cold pressed oils can be applied to the skin as cosmetics. Our observations may be helpful for general practitioners when choosing natural cosmetics.

Essential oils: extraction, bioactivities, and their uses for food preservation.

Science.gov (United States)

Tongnuanchan, Phakawat; Benjakul, Soottawat

2014-07-01

Essential oils are concentrated liquids of complex mixtures of volatile compounds and can be extracted from several plant organs. Essential oils are a good source of several bioactive compounds, which possess antioxidative and antimicrobial properties. In addition, some essential oils have been used as medicine. Furthermore, the uses of essential oils have received increasing attention as the natural additives for the shelf-life extension of food products, due to the risk in using synthetic preservatives. Essential oils can be incorporated into packaging, in which they can provide multifunctions termed "active or smart packaging." Those essential oils are able to modify the matrix of packaging materials, thereby rendering the improved properties. This review covers up-to-date literatures on essential oils including sources, chemical composition, extraction methods, bioactivities, and their applications, particularly with the emphasis on preservation and the shelf-life extension of food products. © 2014 Institute of Food Technologists®

Purification of water polluted with oil and sulfurous closed-ring and aromatic compounds contained in oil and oil products using bacteria relating to thiosphaera

International Nuclear Information System (INIS)

Kurashov, V.M.; Sakhno, T.V.; Gavrilov, V.S.; Zijatdinov, R.N.

2005-01-01

The intensity of natural purification (self-purification) of reservoirs polluted with oil and oil products is determined by microorganisms. Hydrocarbon-oxidizing microorganisms are constant natural constituent of biocenose in reservoirs. However, as a result of outflows, the oil and oil products concentration exceeds maximum values allowing normal vital functions of microorganisms resulting in breaking micro-biocenose suppression of vital functions of bacteria. In this regard, elective anaerobic microorganisms of Thiosphaera are worthy of notice. We found out that bacteria belonging to Thiosphaera pantotropha decomposed oil at high oil concentrations in water (at oil concentration like 1 liter of oil in 1 liter of water). And this is when aerobic microorganisms lose their vital functions at maximum concentration of 20 g of oil in 1 liter of water. To intensify the process of oil decomposition we emulsified oil with aqueous solutions of salts. Thiosphaera pantotropha are found out to decompose oil in a wide range of ratio between oil and aqueous solutions of salts: from 1:10 to 10:1. The water solutions salinity made from 20 g/l to 80 g/l. It must be noticed that, since the Thiosphaera pantotropha are elective anaerobes and decompose oil both in presence and in absence of oxygen, it is not necessary anymore to conduct the process under strictly anaerobic conditions and to supply additional oxygen. This makes it possible to simplify the process of biodegradation of oil and to make this process practically more feasible and economically more profitable being compared to the processes based on the use of other species of bacteria. We found out that Thiosphaera decompose sulfurous closed-ring and aromatic compounds in oil which are chemically and thermally stable and can be hardly decomposed, and possess extremely poisonous properties, as well. The use of microorganisms of Thiosphaera pantotropha allows to purify waters polluted with oil and oil products both during

A numerical study on the oil retention of R410A and PVE oil mixture in multi heat pump system

Energy Technology Data Exchange (ETDEWEB)

Kim, Hak Soo; Kim, Min Soo [Seoul National University, Seoul (Korea, Republic of)

2016-04-15

Predicting an amount of discharged oil from a compressor is necessary to charge the compressor with proper amount of oil. The amount of discharged oil can be predicted by calculating the oil retention amount in each component of a heat pump system. This study suggests a method for calculating the oil retention amount in a heat pump system. In addition, flow pattern of refrigerant and oil mixture in horizontal gas line of refrigerant was ascertained by flow visualization. The oil retention amounts in each component of multi heat pump system were calculated with respect to mass flux of refrigerant, Oil circulation ratio (OCR), length of horizontal and vertical lines. Oil retention amounts in horizontal and vertical gas lines of refrigerant were significant. To validate the model for gas lines of refrigerant, comparison between predicted and experimental oil retention amounts was conducted, and mean absolute percentage error was 15.0%.

Geochemical characteristics of crude oil from a tight oil reservoir in the Lucaogou Formation, Jimusar Sag, Junggar Basin

Science.gov (United States)

Cao, Z.

2015-12-01

Jimusar Sag, which lies in the Junggar Basin,is one of the most typical tight oil study areas in China. However, the properties and origin of the crude oil and the geochemical characteristics of the tight oil from the Lucaogou Formation have not yet been studied. In the present study, 23 crude oilsfrom the Lucaogou Formation were collected for analysis, such as physical properties, bulk composition, saturated hydrocarbon gas chromatography-mass spectrometry (GC-MS), and the calculation of various biomarker parameters. In addition,source rock evaluation and porosity permeability analysis were applied to the mudstones and siltstones. Biomarkers of suitable source rocks (TOC>1, S1+S2>6mg/g, 0.7%oil-source correlation. To analyze the hydrocarbon generation history of the Lucaogou source rock, 1D basin modeling was performed. The oil-filling history was also defined by means of basin modeling and microthermometry. The results indicated the presence of low maturity to mature crude oils originating from the burial of terrigenous organic matter beneath a saline lake in the source rocks of mainly type II1kerogen. In addition, a higher proportion of bacteria and algae was shown to contribute to the formation of crude oil in the lower section when compared with the upper section of the Lucaogou Formation. Oil-source correlations demonstrated that not all mudstones within the Lucaogou Formation contributed to oil accumulation.Crude oil from the upper and lower sections originated from thin-bedded mudstones interbedded within sweet spot sand bodies. A good coincidence of filling history and hydrocarbon generation history indicated that the Lucaogou reservoir is a typical in situ reservoir. The mudstones over or beneath the sweet spot bodies consisted of natural caprocks and prevented the vertical movement of oil by capillary forces. Despite being thicker, the thick-bedded mudstone between the upper and lower sweet spots had no obvious contribution to

Quality evaluation of rapeseed oils used as engine fuels

Directory of Open Access Journals (Sweden)

Marek Světlík

2012-01-01

Full Text Available Samples from six reference decentralised facilities and one industrial production unit of rapeseed oils were taken for the evaluation of the influence of production processes to the properties specified in the technical standard; in the laboratories, the properties limited by the standard for rapeseed oils were determined. In addition, long-term monitoring of changes in the oxidation stability in the storage test of rapeseed oils additived in the quantities of 200, 400 and 600 mg.kg−1 of the Baynox antioxidant was started. The results confirmed that the critical points in the rapeseed oil production process consist in the contamination with ash-forming elements, such as phosphorus, magnesium, calcium and overall impurities. Not only in the case of hot pressing, but also in two-step cold pressing of rapeseed it is necessary to reduce the content of ash-forming elements using additional processes, such as degumming, neutralisation and whitening. The safety step consisting of filtration down to maximum particle size of 1 μm must be always in place before the oil distribution. A positive effect of the Baynox antioxidant was clearly proved. As 200 mg.kg−1 of Baynox was added, the oxidation stability value increased from 8 to 9.05 hrs immediately after the pressing with a consequent decrease to 6 hrs after 270 days. With using of addition 400 ppm Baynox decreased oxidation stability under 6 hours not until after 390 days of storage. With addition 600 ppm Baynox the oxidation stability of rapeseed oil even after 510 days of storage makes 6.5 hours. The quality monitoring brought about necessary findings and knowledge for the optimisation of the rapeseed oil production and distribution as engine fuels. In addition, it serves as an initial supporting document for the creation of the necessary quality control system.

Mining and oil. Oil shale's contribution to future oil supply; Bergbau und Oel. Der Beitrag des Oelschiefers zur Oelversorgung

Energy Technology Data Exchange (ETDEWEB)

Linden, Eike von der [Linden Advisory, Dreieich (Germany)

2012-05-15

principally differ from secondary and tertiary exploitation enhancement methods for conventional oil. The exploitation of shale oil may reach 12% of the oil in place. In difference to shale oil, oil shale is another unconventional oil resource which is contained in shale sediments closer to surface. For lack of sufficient temperature the animal substance has not been completely converted into liquid hydrocarbons but exists as waxy kerogen. Mostly all shale rock which counts for approximately 25% of rock formations close to surface contain more or less animal substance or kerogen which in addition is affiliated by fix carbon as relict of herbal substance. A classification of oil shale depends on the kerogen content. At prevailing oil prices > US Dollars 100/bbl the cut off grade to oil shale be around 6 to 7 % kerogen content. Before the use of oil shale as an unconventional oil resource is discussed for the sake of completeness oil sand and heavy oil shall be described. These hydrocarbons are matured but of long molecular chains with low viscosity, i.e. no flow and contained in sandstones or weathered sand formations. Oil sands - e.g. the Athabasca oil sands in Canada - and heavy oil - e.g. the Orinoco heavy oil - need special exploitation methods. The resources also count for unconventional oil. (orig.)

Corexit 9500 Enhances Oil Biodegradation and Changes Active Bacterial Community Structure of Oil-Enriched Microcosms.

Science.gov (United States)

Techtmann, Stephen M; Zhuang, Mobing; Campo, Pablo; Holder, Edith; Elk, Michael; Hazen, Terry C; Conmy, Robyn; Santo Domingo, Jorge W

2017-05-15

To better understand the impacts of Corexit 9500 on the structure and activity levels of hydrocarbon-degrading microbial communities, we analyzed next-generation 16S rRNA gene sequencing libraries of hydrocarbon enrichments grown at 5 and 25°C using both DNA and RNA extracts as the sequencing templates. Oil biodegradation patterns in both 5 and 25°C enrichments were consistent with those reported in the literature (i.e., aliphatics were degraded faster than aromatics). Slight increases in biodegradation were observed in the presence of Corexit at both temperatures. Differences in community structure were observed between treatment conditions in the DNA-based libraries. The 25°C consortia were dominated by Vibrio , Idiomarina , Marinobacter , Alcanivorax , and Thalassospira species, while the 5°C consortia were dominated by several species of the genera Flavobacterium , Alcanivorax , and Oleispira Most of these genera have been linked to hydrocarbon degradation and have been observed after oil spills. Colwellia and Cycloclasticus , known aromatic degraders, were also found in these enrichments. The addition of Corexit did not have an effect on the active bacterial community structure of the 5°C consortia, while at 25°C, a decrease in the relative abundance of Marinobacter was observed. At 25°C, Thalassospira , Marinobacter , and Idiomarina were present at higher relative abundances in the RNA than DNA libraries, suggesting that they were active in degradation. Similarly, Oleispira was greatly stimulated by the addition of oil at 5°C. IMPORTANCE While dispersants such as Corexit 9500 can be used to treat oil spills, there is still debate on the effectiveness on enhancing oil biodegradation and its potential toxic effect on oil-degrading microbial communities. The results of this study provide some insights on the microbial dynamics of hydrocarbon-degrading bacterial populations in the presence of Corexit 9500. Operational taxonomic unit (OTU) analyses

Acoustic Profiling of Bottom Sediments in Large Oil Storage Tanks

Science.gov (United States)

Svet, V. D.; Tsysar', S. A.

2018-01-01

Characteristic features of acoustic profiling of bottom sediments in large oil storage tanks are considered. Basic acoustic parameters of crude oil and bottom sediments are presented. It is shown that, because of the presence of both transition layers in crude oil and strong reverberation effects in oil tanks, the volume of bottom sediments that is calculated from an acoustic surface image is generally overestimated. To reduce the error, additional post-processing of acoustic profilometry data is proposed in combination with additional measurements of viscosity and tank density distributions in vertical at several points of the tank.

Detection of argan oil adulteration with vegetable oils by high-performance liquid chromatography-evaporative light scattering detection.

Science.gov (United States)

Salghi, Rachid; Armbruster, Wolfgang; Schwack, Wolfgang

2014-06-15

Triacylglycerol profiles were selected as indicator of adulteration of argan oils to carry out a rapid screening of samples for the evaluation of authenticity. Triacylglycerols were separated by high-performance liquid chromatography-evaporative light scattering detection. Different peak area ratios were defined to sensitively detect adulteration of argan oil with vegetable oils such as sunflower, soy bean, and olive oil up to the level of 5%. Based on four reference argan oils, mean limits of detection and quantitation were calculated to approximately 0.4% and 1.3%, respectively. Additionally, 19 more argan oil reference samples were analysed by high-performance liquid chromatography-refractive index detection, resulting in highly comparative results. The overall strategy demonstrated a good applicability in practise, and hence a high potential to be transferred to routine laboratories. Copyright © 2013 Elsevier Ltd. All rights reserved.

Technological advancements revitalize conventional oil sector

International Nuclear Information System (INIS)

Thomson, L.

2000-01-01

Maturing reserves in the Western Canada Sedimentary Basin is resulting in a gradual shift of focus from huge new discoveries and wildcat gushers to developing new technologies for exploration and enhanced recovery techniques of production, keeping costs down and reducing environmental impacts, as a means of keeping conventional oil plays a viable force in the oil and gas industry. The value in refocusing efforts towards technology development is given added weight by a recent announcement by the Petroleum Communication Foundation, which stated that in addition to the oil sands and offshore oil and gas developments, one of the country's largest undeveloped oil resource is the 70 per cent of discovered crude oil in western Canadian pools that cannot be recovered by current conventional production techniques. Therefore, development of new technologies to exploit these currently unrecoverable resources is a matter of high priority. To remain competitive, the new techniques must also lower the cost of recovering oil from these sources, given that the cost of oil production in Canada is already higher than that in most other competing countries

Detection of plant oil DNA using high resolution melting (HRM) post PCR analysis: a tool for disclosure of olive oil adulteration.

Science.gov (United States)

Vietina, Michelangelo; Agrimonti, Caterina; Marmiroli, Nelson

2013-12-15

Extra virgin olive oil is frequently subjected to adulterations with addition of oils obtained from plants other than olive. DNA analysis is a fast and economic tool to identify plant components in oils. Extraction and amplification of DNA by PCR was tested in olives, in milled seeds and in oils, to investigate its use in olive oil traceability. DNA was extracted from different oils made of hazelnut, maize, sunflower, peanut, sesame, soybean, rice and pumpkin. Comparing the DNA melting profiles in reference plant materials and in the oils, it was possible to identify any plant components in oils and mixtures of oils. Real-Time PCR (RT-PCR) platform has been added of the new methodology of high resolution melting (HRM), both were used to analyse olive oils mixed with different percentage of other oils. Results showed HRM a cost effective method for efficient detection of adulterations in olive oils. Copyright © 2013 Elsevier Ltd. All rights reserved.

Pigouvian penalty for oil spills

International Nuclear Information System (INIS)

Kohn, R.E.

1993-01-01

The imposition of ex ante taxes on expected spilled oil, in addition to ex post payments for damages under tort liability, would foster economic efficiency. This paper begins the analysis of the joint approach with the case in which Pigouvian taxes are used exclusively. A model is developed in which the volume of spilled oil causing environmental damage is reduced, first by spill prevention expenditures by shippers and then by clean-up expenditures by the government. The efficient Pigouvian tax on expected spilled oil equals marginal environmental damage which equals the net marginal cost of prevention which equals marginal clean-up cost. (Author)

A fear index to predict oil futures returns

International Nuclear Information System (INIS)

Chevallier, Julien; Sevi, Benoit

2013-01-01

This paper evaluates the predictability of WTI light sweet crude oil futures by using the variance risk premium, i.e. the difference between model-free measures of implied and realized volatilities. Additional regressors known for their ability to explain crude oil futures prices are also considered, capturing macro-economic, financial and oil-specific influences. The results indicate that the explanatory power of the (negative) variance risk premium on oil excess returns is particularly strong (up to 25% for the adjusted R-squared across our regressions). It complements other financial (e.g. default spread) and oil-specific (e.g. US oil stocks) factors highlighted in previous literature. (authors)

Microbial population changes during bioremediation of an experimental oil spill

International Nuclear Information System (INIS)

Venosa, A.D.; Stephen, J.R.; Macnaughton, S.J.; Chang, Y.; White, D.C.

2000-01-01

Three crude oil bioremediation techniques were tested in a field experiment in Delaware, United States to determine the progress of natural and accelerated attenuation during a controlled oil spill. The four treatments studied were: no oil control, oil alone, oil plus nutrients, and oil plus nutrients plus an indigenous inoculum. During the first 14 weeks, microbial numbers were high but were steadily declining with no major differences among treatments. However, after the 14 week period, phospholipid fatty acid (PLFA) results showed that the communities shifted from being composed mostly of eukaryotes to gram-negative bacteria. The dominant species diversity changed and increased significantly over 14 weeks. Nutrient addition and the addition of the indigenous inoculum altered the nature of this change. Gas chromatography/mass spectrometry analyses of the oil analytes detected major differences in rates of biodegradation between the amended and unamended natural attenuation plots, but not between the nutrient and inoculum plots. 11 refs., 3 figs

Profiling of Indigenous Microbial Community Dynamics and Metabolic Activity During Enrichment in Molasses-Supplemented Crude Oil-Brine Mixtures for Improved Understanding of Microbial Enhanced Oil Recovery

DEFF Research Database (Denmark)

Halim, Amalia Yunita; Pedersen, Dorthe Skou; Nielsen, Sidsel Marie

2015-01-01

Anaerobic incubations using crude oil and brine from a North Sea reservoir were conducted to gain increased understanding of indigenous microbial community development, metabolite production, and the effects on the oil–brine system after addition of a complex carbon source, molasses, with or with...... of molasses has potential as microbial enhanced oil recovery (MEOR) strategy in North Sea oil reservoirs.......Anaerobic incubations using crude oil and brine from a North Sea reservoir were conducted to gain increased understanding of indigenous microbial community development, metabolite production, and the effects on the oil–brine system after addition of a complex carbon source, molasses....... The microbial growth caused changes in the crude oil–brine system: formation of oil emulsions, and reduction of interfacial tension (IFT). Reduction in IFT was associated with microbes being present at the oil–brine interphase. These findings suggest that stimulation of indigenous microbial growth by addition...

Clean and Secure Energy from Domestic Oil Shale and Oil Sands Resources

Energy Technology Data Exchange (ETDEWEB)

Spinti, Jennifer [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Birgenheier, Lauren [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Deo, Milind [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Facelli, Julio [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Hradisky, Michal [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Kelly, Kerry [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Miller, Jan [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); McLennan, John [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Ring, Terry [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Ruple, John [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Uchitel, Kirsten [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States)

2015-09-30

This report summarizes the significant findings from the Clean and Secure Energy from Domestic Oil Shale and Oil Sands Resources program sponsored by the Department of Energy through the National Energy Technology Laboratory. There were four principle areas of research; Environmental, legal, and policy issues related to development of oil shale and oil sands resources; Economic and environmental assessment of domestic unconventional fuels industry; Basin-scale assessment of conventional and unconventional fuel development impacts; and Liquid fuel production by in situ thermal processing of oil shale Multiple research projects were conducted in each area and the results have been communicated via sponsored conferences, conference presentations, invited talks, interviews with the media, numerous topical reports, journal publications, and a book that summarizes much of the oil shale research relating to Utah’s Uinta Basin. In addition, a repository of materials related to oil shale and oil sands has been created within the University of Utah’s Institutional Repository, including the materials generated during this research program. Below is a listing of all topical and progress reports generated by this project and submitted to the Office of Science and Technical Information (OSTI). A listing of all peer-reviewed publications generated as a result of this project is included at the end of this report; Geomechanical and Fluid Transport Properties 1 (December, 2015); Validation Results for Core-Scale Oil Shale Pyrolysis (February, 2015); and Rates and Mechanisms of Oil Shale Pyrolysis: A Chemical Structure Approach (November, 2014); Policy Issues Associated With Using Simulation to Assess Environmental Impacts (November, 2014); Policy Analysis of the Canadian Oil Sands Experience (September, 2013); V-UQ of Generation 1 Simulator with AMSO Experimental Data (August, 2013); Lands with Wilderness Characteristics, Resource Management Plan Constraints, and Land Exchanges

Tank testing of skimmers with waxy and viscous oils

International Nuclear Information System (INIS)

1989-10-01

A series of tests of four offshore skimmers (Framo ACW-400, GT-185, Walosep W2, Heavy Oil Skimmer) was conducted in a 120-by-60-meter wave basin. Each skimmer was tested with each of 3 oils: a conventional crude, a waxy crude, and a bunker oil. Each test involved 4-6 h of skimming, partly conducted in waves having a period of 4 s and heights of 0.4-0.8 m. Near the end of selected tests, the additive Elastol was applied to the oil and its effect on recovery parameters evaluated. All the optimum results were obtained in calm conditions. In general, waves had no effect on the performance of the Walosep W2, had little effect on the performance of the GT-185, and greatly reduced the performance of the Framo. The experimental Heavy Oil Skimmer failed to recover oil at significant rates without addition of Elastol to the oils. The fluid recovery rate less the water entrainment rate generally declined as oil viscosity increased. For a waxy oil, recovery rates under conditions typical of the Grand Banks in summer would be 30-40% less than for a conventional crude with the Framo skimmer and about the same as the recovery rates for conventional crude with the Walosep and GT-185 skimmers. The Walosep, unlike the other skimmers, did not entrain more water when skimming waxy oil compared to conventional oil. Adding Elastol to the oils improved the corrected recovery rates of the Walosep by ca 15% and had no effect on its water entrainment rate. For the Framo, Elastol addition had no effect on the recovery rate but increased its water entrainment rate. Elastol reduced the GT-185's recovery rate by 25-35% and increased its water entrainment rate. Adding Elastol had several negative effects on subsequent downstream operations. 11 refs., 55 figs., 14 tabs

Environmentally safe oil-field reagents for development and operation of oil-gas deposits

Science.gov (United States)

Fakhreeva, A. V.; Manaure, D. A.; Dokichev, V. A.; Voloshin, A. I.; Telin, A. G.; Tomilov, Yu V.; Nifantiev, N. E.

2018-04-01

Sodium-carboxymethylcellulose and arabinogalactane inhibits the crystallization of calcium carbonate from a supersaturated aqueous solution at 80°C. The sizes of formed crystals CaCO3 in the presence of arabinogalactane, sodium-carboxymethylcellulose and neonol AF 9-10 decrease on an average 7-12 μm and a change of their structure. It is expected, that the mechanism of inhibitionis in specific adsorption polysaccharides and neonol on occurring crystalline surface of the calcium carbonate, both at the expense of electrostatic interaction of functional groups with Ca2+ ions, located on the surface of the crystal, and due to coordination and hydrogen bonds with oxygen atoms and HO-groups of additives. Oil-water emulsion rheology in the presence of neonol AF 9-10 has been studied. It is shown that neonol AF 9-10 decrease viscosity natural water-oil emulsion by 25 times. Addition of 5% neonol to water-oil emulsion leads to formation more than 20 stable emulsion forms of different density and composition. New highly effective “green” oilfield reagents have been developed on the basis of neonol and natural polysaccharides.

Peru steps up push to attract oil investment

International Nuclear Information System (INIS)

Anon.

1991-01-01

This paper reports that Peru's government is stepping up efforts to attract more foreign investment in its oil and gas sector. Since taking over in July 1990, the government of President Alberto Fujimori has taken a number of steps to privatize the oil sector, improve the fiscal regime for oil investment, and streamline regulations on oil and gas investment. In the most dramatic step, the Fujimori administration ended state oil company Petroleos del Peru's monopoly on downstream operations as well as imports and exports of oil and gas as part of sweeping new oil and gas legislation. In addition, officials of the Fujimori administration have been traveling to key oil centers around the world with a presentation on Peru's hydrocarbon potential, trying to spark interest in E and D investment there

21 CFR 172.862 - Oleic acid derived from tall oil fatty acids.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Oleic acid derived from tall oil fatty acids. 172... FOOD FOR HUMAN CONSUMPTION Multipurpose Additives § 172.862 Oleic acid derived from tall oil fatty acids. The food additive oleic acid derived from tall oil fatty acids may be safely used in food and as...

Salt marsh recovery from a crude oil spill: Vegetation, oil weathering, and response

International Nuclear Information System (INIS)

Hoff, R.Z.; Shigenaka, G.; Henry, C.B. Jr.

1993-01-01

When a spill of Prudhoe Bay crude oil covered a fringing Salicornia virginica marsh in Fidalgo Bay, Washington (northern Puget Sound) in February 1991, response personnel used several low-impact techniques to remove oil from the marsh, and minimized access by cleanup workers. Following the response, a monitoring program was established to track marsh recovery, and to document the effectiveness of the response techniques used and their impacts on the marsh. Through monthly sampling over a 16-month period, vegetative growth was monitored and chemical degradation of remaining oil was tracked. Sampling was conducted along transects located in four areas affected in different ways by the spill, including an oiled, trampled section; an oiled, vacuumed section; and an oiled, washed, and vacuumed section. In addition, a control transect was established in an unoiled adjacent marsh. The study included both biological and chemical components. Biological measurements included percent cover of live vegetation (sampled monthly) and below-ground plant biomass (sampled at the beginning of each growing season in April 1991 and April 1992). Sediment samples included surface sediment (monthly) and core samples collected at the beginning and end of the growing seasons. Sediment samples were analyzed using gas chromatography/mass spectroscopy, and indicator compounds were tracked to determine rates of oil degradation. Results from 16 months of post-spill monitoring show that foot trampling was most detrimental to marsh plants, while washing with vacuuming removed the most oil and minimized adverse impacts to vegetation. Dense clay substrate helped prevent oil from penetrating the sediment, thus minimizing acute toxic effects from oil exposure to marsh plant rootstock. By the second growing season post-spill, Salicornia and other marsh plants were growing in all areas except one heavily oiled patch

40 CFR 300.175 - Federal agencies: additional responsibilities and assistance.

Science.gov (United States)

2010-07-01

... command, control, and surveillance of oil discharges and hazardous substance releases occurring in the..., transport by rail and containers or bulk transport of oil. (13) The Department of State (DOS) will lead in... vessels. Additionally, DOS will coordinate requests for assistance from foreign governments and U.S...

Evaluation of the efficiency of silicone polyether additives as foam inhibitor in crude oil; Avaliacao da eficiencia de aditivos a base de silicone polieter como inibidores de espuma em petroleo

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-07-01

This work evaluates the chemical and physico-chemical properties of commercial anti-foam products based on silicone polyethers along with their efficiency in inhibiting foaming. The commercial surfactants were characterized by nuclear magnetic resonance (NMR) spectroscopy, size exclusion chromatography (SEC), determination of solubility in different solvents and measurement of the surface and interfacial tensions. A method to test the formation of foam in oil was used to mimic the operating conditions in gas-oil separators. The results show that the most polar additive was the most efficient in breaking up the foam. (author)

Effect of nanoparticles as lubricant additives on friction and wear behavior of tetrahedral amorphous carbon (ta-C coating

Directory of Open Access Journals (Sweden)

Xiang Li

2018-03-01

Full Text Available As diamond like carbon (DLC coating becomes increasingly popular in providing low friction and wear under lubricated conditions, the effect of various oil additives on tribological behavior of DLC coating is drawing more attention. Various oil additives, such as ZnDTP and MoDTC, have been widely used in automobile engine industry to pursuit excellent tribological performance in the insufficient lubrication condition. Although such commercial oil additives have been proven to reduce friction or/and wear to some extent, usage of such high -SAPS (sulphuric ash, phosphor, sulfphur conventional additives is bound to arouse concerns due to environmental reasons. In this research, we investigate the effect of two nanoparticle oil additives, which are cerium oxide (CeO2 and zirconium dioxide (ZrO2, on friction and wear of non-hydrogen tetrahedral amorphous carbon (ta-C coating. The results show that by adding ZrO2 nanoparticle, the friction of DLC coating could be reduced about 32% compared to non-additive base oil scenario, but specific wear rate increases by 40%. When CeO2 nanoparticle is used, friction increases by 22% compared to non-additive base oil scenario, however wear decreases by nearly 77%.

The economic growth of oil countries

International Nuclear Information System (INIS)

Arbod, G.

2007-02-01

The literature tries to apprehend the weakness of the economic growth of oil culminates by the assumption of ousted growth factors. In the Dutch Disease models the non-oil exporting sector would be ousted whereas in the analyses in terms of economic policies it would be the efficient economic policies. We consider the phenomenon through the growth theories, the oil income being regarded as an additional exogenous income for the economy. In this manner the growth dynamic of oil countries, even the most unfavourable, can be modelled without utilizing any concept of economic inefficiency. The last part of our work is devoted to the Saudi economy. After having developed a macro-econometric model, and using scenarios of oil prices, we lead a forecasted analysis of this economy. (author)

Microbial enhanced heavy crude oil recovery through biodegradation using bacterial isolates from an Omani oil field.

Science.gov (United States)

Al-Sayegh, Abdullah; Al-Wahaibi, Yahya; Al-Bahry, Saif; Elshafie, Abdulkadir; Al-Bemani, Ali; Joshi, Sanket

2015-09-16

Biodegradation is a cheap and environmentally friendly process that could breakdown and utilizes heavy crude oil (HCO) resources. Numerous bacteria are able to grow using hydrocarbons as a carbon source; however, bacteria that are able to grow using HCO hydrocarbons are limited. In this study, HCO degrading bacteria were isolated from an Omani heavy crude oil field. They were then identified and assessed for their biodegradation and biotransformation abilities under aerobic and anaerobic conditions. Bacteria were grown in five different minimum salts media. The isolates were identified by MALDI biotyper and 16S rRNA sequencing. The nucleotide sequences were submitted to GenBank (NCBI) database. The bacteria were identified as Bacillus subtilis and B. licheniformis. To assess microbial growth and biodegradation of HCO by well-assay on agar plates, samples were collected at different intervals. The HCO biodegradation and biotransformation were determined using GC-FID, which showed direct correlation of microbial growth with an increased biotransformation of light hydrocarbons (C12 and C14). Among the isolates, B. licheniformis AS5 was the most efficient isolate in biodegradation and biotransformation of the HCO. Therefore, isolate AS5 was used for heavy crude oil recovery experiments, in core flooding experiments using Berea core plugs, where an additional 16 % of oil initially in place was recovered. This is the first report from Oman for bacteria isolated from an oil field that were able to degrade and transform HCO to lighter components, illustrating the potential use in HCO recovery. The data suggested that biodegradation and biotransformation processes may lead to additional oil recovery from heavy oil fields, if bacteria are grown in suitable medium under optimum growth conditions.

The oil supply mountain - is the summit in sight?

International Nuclear Information System (INIS)

Barnes, Philip.

1993-01-01

A brief review of the current status of global oil reserves and the prospects of recovering this oil at prices less than $30 a barrel is presented. In addition to the uncertainties over the volumes of recoverable oil at various costs, there are many uncertainties not least geopolitical ones. (UK)

21 CFR 573.660 - Methyl glucoside-coconut oil ester.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Methyl glucoside-coconut oil ester. 573.660 Section 573.660 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... ANIMALS Food Additive Listing § 573.660 Methyl glucoside-coconut oil ester. Methyl glucoside-coconut oil...

Experimental and numerical modeling of heavy-oil recovery by electrical heating

Energy Technology Data Exchange (ETDEWEB)

Hascakir, B.; Akin, S. [Middle East Technical Univ., Ankara (Turkey); Babadagli, T. [Alberta Univ., Edmonton, AB (Canada)

2008-10-15

This study examined the applicability of electrical heating as a heavy oil recovery system in 2 heavy oil fields in Turkey. The physical and chemical properties of samples from the 2 fields were compiled and measured. The samples were then subjected to electrical heating. A retort technique was used to determine oil recovery performance under various conditions. Different types of iron powders were also applied in order to reduce oil viscosity. In situ viscosity reduction levels during the heating process were measured using a history matching procedure that considered data obtained during the laboratory experiments. The study demonstrated that the addition of iron power to the oil samples caused the polar components of the oil to decrease. Oil viscosity was strongly influenced by the magnetic fields created by the iron powders. An analysis of the experimental data showed that significant viscosity reductions of 88 per cent were obtained for the samples when iron additions of 0.5 per cent were used. Data from the experiments were used to develop mathematical models in order to consider thermal diffusion coefficients, oil viscosity, and relative permeability parameters. It was concluded that the cost of producing 1 barrel of oil using the method cost approximately US $5. After a period of 70 days, 320 barrels of petroleum were produced using the method. Oil production rates increased to 440 barrels over the same time period when iron additions were used. 30 refs., 6 tabs., 12 figs.

Effects of additives on glyphosate activity in purple nutsedge

International Nuclear Information System (INIS)

Rungsit Suwanketnikom

1998-01-01

Effects of additives on 14 C-glyphosate penetration into purple nutsedge leaves were examined in the laboratory and efficacy of glyphosate for purple nutsedge control was studied in the greenhouse and field. The addition of (NH 4 ) 2 SO 4 at 1.0% (v/v) + diesel oil at 1,0% (v/v) + Tendal at 1.0% (v/v) increased 14 C-glyphosate penetration into nutsedge leaves more than the addition of either one alone. (NH 4 ) 2 SO 4 at 1.0% + diesel oil at 1.0% + Tendal at 0.12 or 0.25% increased the phytotoxicity of glyphosate at 0.5 and 0.75 kg, a.e./ha on nutsedge plants in the greenhouse but not in the field. Additives did not enhance glyphosate activity by reducing the number of nutsedae tubers. (author)

Oxidative stability, chemical composition and organoleptic properties of seinat (Cucumis melo var. tibish) seed oil blends with peanut oil from China.

Science.gov (United States)

Siddeeg, Azhari; Xia, Wenshui

2015-12-01

Seinat seed oil was blended with peanut oil for the enhancement of stability and chemical characteristics of the blend. The physicochemical properties (relative density, refractive index, free fatty acids, saponification value, iodine value and peroxide value) of seinat seed and peanut oil blends in ratios 95:5, 85:15, 30:70 and 50:50 proportions were evaluated, as well as oxidative stability index, deferential scanning calorimetric (DSC) characteristics and tocopherols content. Results of oil blend showed that there was no negative effect by the addition of seinat seed oil to peanut oil and also had decreased percentages of all saturated fatty acids except stearic acid, conversely, increased the levels of unsaturated fatty acids. As for the sensory evaluation, the panelist results showed that seinat seed oil blends had no significant differences (p blending of seinat seed oil with peanut oil had also increased the stability and tocopherols content. As Sudan is the first producer of seinat oil, blending of seinat seed oil with traditional oil like quality, and may decrease the consumption of other expensive edible oils.

Investigation of non-volatile additives on the process of distillation of hydrocarbon mixtures

Directory of Open Access Journals (Sweden)

М.Б. Степанов

2009-02-01

Full Text Available  The given results of researches of influence of nonvolatile additives on processes of distillation of individual hydrocarbons and their mixes, including petroleum and mineral oil. With the help of the developed computer system of the continuous control of distillation it is shown, that at the presence of small amounts of the additive decrease of temperature of the beginning of boiling of hydrocarbons is observed, their speeds of banish and exits of light fuel mineral oil grow during initial oil refining

Antiwear and antioxidant studies of cardanol phosphate ester additives

Energy Technology Data Exchange (ETDEWEB)

Mazzetto, S.E.; Oliveira, L.D.M.; Lomonaco, D.; Veloso, P.A., E-mail: selma@ufc.br [Lab. de Produtos e Tecnologia em Processos (LPT), Dept. de Quimica Organica e Inorganica, Universidade Federal do Ceara, Fortaleza, CE (Brazil)

2012-07-15

In the search for new applications and products derived from Cashew Nut Shell Liquid (CNSL), we report herein the synthesis and characterization (GC/MS and {sup 1}H, {sup 13}C, and {sup 31}P NMR) of four phosphate esters derived from hydrogenated cardanol, including their applications as antiwear additives for diesel (S500) and as antioxidant additives for mineral oils, evaluated through the HFRR test and oxidative stability analyses, respectively. The results obtained showed very good to excellent performances promoted by the bioadditives evaluated, especially for the thiophosphorylated derivative, which notably reduced the sludge residue and the acidity index of the oxidized oil (0.52 mg NaOH/g sample) and also improved the diesel lubricity, reducing the wear of metal parts by more than 50% (330 {Mu}m). Keywords: Cardanol; Antiwear; Antioxidant; Diesel; Mineral oil. (author)

Mechanical - physical treatment of used motor oil within a sustainable waste management system

Directory of Open Access Journals (Sweden)

Đukić Veljko N.

2015-01-01

Full Text Available Waste oils are all mineral or synthetic oils that cannot be used for the purpose for which they were originally produced. These are: hydraulic oils, motor oils, ship oils, liquids for the transfer of heat or insulation, oily remains from reservoirs, oil-water emulsions and various oil-water mixtures. In its chemical makeup used motor oil contains hydrocarbons, organic minerals, heavy metals (cobalt, magnesium, iron, zinc, sulfur, chlorine, nitrogen, phosphorus, compounds from additives and other products that are dangerous as they have cancerous effects on health. As it is considered the biggest contaminant of the environment and classified as hazardous waste; special attention must be given in the handling of used motor oil to ensure its appropriate disposal. Setting up of a viable system for Mechanical-Physical Treatment of used motor oil makes it possible to re-use it as a secondary raw material i.e. the problem of collection, transportation, treatment and storing of the used motor oil is being solved. . The subject of this research is the advantage of the mechanical-physical treatment of used motor oil. Re- refined motor oil can be used for multiple purposes such as a base for the other synthetic oils, for heating etc. Improper disposal of used motor oil causes multiple damage; firstly, losing the valuable secondary base which, with the addition of certain additives, can be used as the basis for the other synthetic oils; secondly, causing damage to the environment by the pollution with inability to repair the damage to all environmental components.

21 CFR 172.816 - Methyl glucoside-coconut oil ester.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Methyl glucoside-coconut oil ester. 172.816 Section... HUMAN CONSUMPTION Multipurpose Additives § 172.816 Methyl glucoside-coconut oil ester. Methyl glucoside-coconut oil ester may be safely used in food in accordance with the following conditions: (a) It is the...

New lube oil for stationary heavy fuel engines

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

An extensively field-tested diesel engine lubricating oil for medium speed, heavy fuel stationary engine applications has been introduced by Caltex Petroleum, in Dallas, Texas. The new oil is similar to a product developed and marketed for marine medium speed heavy fuel propulsion and auxillary engine applications by one of its two parent companies, Chevron. Detailed are results of two field evaluations in Caterpillar 3600 series engines installed at Kimberly Clark (KCPI) and Sime Darby (SDPI), both in the Philippines. Both were one year, 7000-plus hour field evaluations of a new, 40 BN trunk piston engine oil (TPEO), identified as Caltex Delo 3400, SAE 40 engine lube oil. The oil uses the new Phenalate additive technology developed by Chevron Chemical Company`s Oronite Additives Division. This technology is designed to improve engine cleanliness in regard to soft black sludge and piston deposits. The focus of the field evaluations was the performance of the lubricating oil. During controlled tests at Sime Darby, the most noticeable improvement over another technology was in the control of sludge deposits. This improvement was seen in all areas where black sludge forms, such as the rocker cover, crankcase cover and valve assemblies. 4 figs.

Comparative Risk Assessment of spill response options for a deepwater oil well blowout: Part 1. Oil spill modeling.

Science.gov (United States)

French-McCay, Deborah; Crowley, Deborah; Rowe, Jill J; Bock, Michael; Robinson, Hilary; Wenning, Richard; Walker, Ann Hayward; Joeckel, John; Nedwed, Tim J; Parkerton, Thomas F

2018-05-31

Oil spill model simulations of a deepwater blowout in the Gulf of Mexico De Soto Canyon, assuming no intervention and various response options (i.e., subsea dispersant injection SSDI, in addition to mechanical recovery, in-situ burning, and surface dispersant application) were compared. Predicted oil fate, amount and area of surfaced oil, and exposure concentrations in the water column above potential effects thresholds were used as inputs to a Comparative Risk Assessment to identify response strategies that minimize long-term impacts. SSDI reduced human and wildlife exposure to volatile organic compounds; dispersed oil into a large water volume at depth; enhanced biodegradation; and reduced surface water, nearshore and shoreline exposure to floating oil and entrained/dissolved oil in the upper water column. Tradeoffs included increased oil exposures at depth. However, since organisms are less abundant below 200 m, results indicate that overall exposure of valued ecosystem components was minimized by use of SSDI. Copyright © 2018 Elsevier Ltd. All rights reserved.

Method of removing radioactive waste from oil

International Nuclear Information System (INIS)

Belanger, R.L.

1986-01-01

This patent describes a method of removing particulates, radioactive contaminants, and moisture from oil, which consists of: straining out the particulates by passing the oil through a coarse filter screen to a receiving vessel; forming an upper stratum of oil and a lower stratum of sludge, consisting of mud, oil, particulates, and moisture, by heating the upper two-thirds of the receiving vessel; skimming off the stratum of oil from the receiving vessel; transferring the sludge from the receiving vessel to a container; transferring additional separated oil to the receiving vessel; conveying the oil skimmed from the receiving vessel to a mixing vessel; adding an effective amount of Calcium Hypochlorite crystals containing 65% free Chlorine to the mixing vessel to initiate salt formation with the radioactive contaminants; mixing the contents of the mixing vessel for at least ten minutes; transferring the mixture from the mixing vessel to a circulating heater; outputting the mixture from the circulating heater to a second mixing vessel; removing moisture from the oil; and filtering from the oil, the solid radioactive contaminant-salts and residual particulate matter

Production of oxidatively stable fish oil enriched food emulsions

DEFF Research Database (Denmark)

Bruni Let, Mette

Purpose: The objective of the project is to determine how a number of selected fish oil enriched foods can be protected against oxidation by the right choice of antioxidants, emulsifiers and optimal process conditions. Furthermore the influence of antioxidant addition to the fish oil it...... have many other health benefiting properties such as preventing heart diseases. Addition of fish oils to foods is therefore of interest. The many double bonds in the fatty acids are however susceptible to oxidation. Collaboration partners: The project is a collaborative project between DFU-FF, Bio......-self on the effect of antioxidants added to the foods will also be investigated. Background: Fish oils are rich sources of the long-chain polyunsaturated fatty acids EPA and DHA of which DHA is a vital component of the phospholipids of human cellular membranes, especially those in the brain and retina. Fish oils...

Simulating surface oil transport during the Deepwater Horizon oil spill: Experiments with the BioCast system

Science.gov (United States)

Jolliff, Jason Keith; Smith, Travis A.; Ladner, Sherwin; Arnone, Robert A.

2014-03-01

The U.S. Naval Research Laboratory (NRL) is developing nowcast/forecast software systems designed to combine satellite ocean color data streams with physical circulation models in order to produce prognostic fields of ocean surface materials. The Deepwater Horizon oil spill in the Gulf of Mexico provided a test case for the Bio-Optical Forecasting (BioCast) system to rapidly combine the latest satellite imagery of the oil slick distribution with surface circulation fields in order to produce oil slick transport scenarios and forecasts. In one such sequence of experiments, MODIS satellite true color images were combined with high-resolution ocean circulation forecasts from the Coupled Ocean-Atmosphere Mesoscale Prediction System (COAMPS®) to produce 96-h oil transport simulations. These oil forecasts predicted a major oil slick landfall at Grand Isle, Louisiana, USA that was subsequently observed. A key driver of the landfall scenario was the development of a coastal buoyancy current associated with Mississippi River Delta freshwater outflow. In another series of experiments, longer-term regional circulation model results were combined with oil slick source/sink scenarios to simulate the observed containment of surface oil within the Gulf of Mexico. Both sets of experiments underscore the importance of identifying and simulating potential hydrodynamic conduits of surface oil transport. The addition of explicit sources and sinks of surface oil concentrations provides a framework for increasingly complex oil spill modeling efforts that extend beyond horizontal trajectory analysis.

Essential oils as a natural additive in the edible films and coatings (active packaging system): A Review

OpenAIRE

R Fattahi; A Bahrami

2018-01-01

Background: Common plastics used in food packaging have a lot of environmental problems. The aim of this study, was to review the latest research results on edible and biodegradable packaging and the positive effect of essential oil in them. Methods: In order to gather information, articles containing one of the words in their text, including: Food packaging, Edible film, Essential oils and Biodegradable film were searched between 1993 and 2017 in Science direct, Elsevier, Springer, Americ...

Antioxidant activity of oregano, parsley, and olive mill wastewaters in bulk oils and oil-in-water emulsions enriched in fish oil.

Science.gov (United States)

Jimenez-Alvarez, D; Giuffrida, F; Golay, P A; Cotting, C; Lardeau, A; Keely, Brendan J

2008-08-27

The antioxidant activity of oregano, parsley, olive mill wastewaters (OMWW), Trolox, and ethylenediaminetetraacetic acid (EDTA) was evaluated in bulk oils and oil-in-water (o/w) emulsions enriched with 5% tuna oil by monitoring the formation of hydroperoxides, hexanal, and t-t-2,4-heptadienal in samples stored at 37 degrees C for 14 days. In bulk oil, the order of antioxidant activity was, in decreasing order (p oregano > parsley > EDTA > Trolox. The antioxidant activity in o/w emulsion followed the same order except that EDTA was as efficient an antioxidant as OMWW. In addition, the total phenolic content, the radical scavenging properties, the reducing capacity, and the iron chelating activity of OMWW, parsley, and oregano extracts were determined by the Folin-Ciocalteau, oxygen radical absorbance capacity, ferric reducing antioxidant power, and iron(II) chelating activity assays, respectively. The antioxidant activity of OMWW, parsley, and oregano in food systems was related to their total phenolic content and radical scavenging capacity but not to their ability to chelate iron in vitro. OMWW was identified as a promising source of antioxidants to retard lipid oxidation in fish oil-enriched food products.

Additive manufacturing of tunable lenses

Science.gov (United States)

Schlichting, Katja; Novak, Tobias; Heinrich, Andreas

2017-02-01

Individual additive manufacturing of optical systems based on 3D Printing offers varied possibilities in design and usage. In addition to the additive manufacturing procedure, the usage of tunable lenses allows further advantages for intelligent optical systems. Our goal is to bring the advantages of additive manufacturing together with the huge potential of tunable lenses. We produced tunable lenses as a bundle without any further processing steps, like polishing. The lenses were designed and directly printed with a 3D Printer as a package. The design contains the membrane as an optical part as well as the mechanical parts of the lens, like the attachments for the sleeves which contain the oil. The dynamic optical lenses were filled with an oil. The focal length of the lenses changes due to a change of the radius of curvature. This change is caused by changing the pressure in the inside of the lens. In addition to that, we designed lenses with special structures to obtain different areas with an individual optical power. We want to discuss the huge potential of this technology for several applications. Further, an appropriate controlling system is needed. Wéll show the possibilities to control and regulate the optical power of the lenses. The lenses could be used for illumination tasks, and in the future, for individual measurement tasks. The main advantage is the individuality and the possibility to create an individual design which completely fulfills the requirements for any specific application.

Alberta's new oil boom

International Nuclear Information System (INIS)

Nikiforuk, A.

1997-01-01

A massive expansion of Canada's oil sands and the oil-mining business is underway. The prediction is that within five years there will be at least three, possibly six, huge new open pit mines north of Fort McMurray, Alberta. It was suggested that within 20 years, possibly half of Canada's oil supply will come from the oil sands industry which has already attracted $10 billion worth of developments. Unlike conventional crude, the oil sands contain bitumen, water, clay, minerals and lots of sands. Shallow deposits are mined like coal. Deeper formations make use of in-situ thermal recovery techniques. Extraction costs are presently at $15 per barrel, aiming for $12 by 1999. Return on investment is in double digits. Estimates of reserves in the Athabasca, Cold Lake, Peace River and Wabasca deposits go as high as 1.7 trillion barrels, or about twice as much as Saudi Arabia's conventional crude reserves. Syncrude has built a $5 billion production facility and two pipelines have already been proposed to transport the oil sands crude to midwestern US refineries. US refineries prize synthetic crude as excellent mixing stock. The major problem with oil sands is that unlike conventional oil, these reserves require an enormous amount of energy to exploit, which in turn means lots of foul air and greenhouse gases. There are many environmental unknowns, and without a clear management framework in sight the addition of two or three Syncrude-size operations has the potential to create a real and significant acid rain problem in the Western Canada Basin

Quantitative effects of the shale oil revolution

International Nuclear Information System (INIS)

Belu Mănescu, Cristiana; Nuño, Galo

2015-01-01

The aim of this paper is to analyze the impact of the so-called “shale oil revolution” on oil prices and economic growth. We employ a general equilibrium model of the world oil market in which Saudi Arabia is the dominant firm, with the rest of the producers as a competitive fringe. Our results suggest that most of the expected increase in US oil supply due to the shale oil revolution has already been incorporated into prices and that it will produce an additional increase of 0.2% in the GDP of oil importers in the period 2010–2018. We also employ the model to analyze the collapse in oil prices in the second half of 2014 and conclude that it was mainly due to positive unanticipated supply shocks. - Highlights: • We analyze the impact of the “shale oil revolution” on oil prices and economic growth. • We employ a general equilibrium model of the oil market in which Saudi Arabia is the dominant firm. • We find that most of the shale oil revolution is already priced in. • We also analyze the decline in oil prices in the second half of 2014. • We find that unanticipated supply shocks played the major role in the fall.

Additional Equipment for Soil Biodegradation

Science.gov (United States)

Vondráčková, Terezie; Kraus, Michal; Šál, Jiří

2017-12-01

Intensification of industrial production, increasing citizens’ living standards, expanding the consumer assortment mean in the production - consumption cycle a constantly increasing occurrence of waste material, which by its very nature must be considered as a source of useful raw materials in all branches of human activity. In addition to strict legislative requirements, a number of circumstances characterize waste management. It is mainly extensive transport associated with the handling and storage of large volumes of substances with a large assortment of materials (substances of all possible physical and chemical properties) and high demands on reliability and time coordination of follow-up processes. Considerable differences in transport distances, a large number of sources, processors and customers, and not least seasonal fluctuations in waste and strong price pressures cannot be overlooked. This highlights the importance of logistics in waste management. Soils that are contaminated with oil and petroleum products are hazardous industrial waste. Methods of industrial waste disposal are landfilling, biological processes, thermal processes and physical and chemical methods. The paper focuses on the possibilities of degradation of oil pollution, in particular biodegradation by bacteria, which is relatively low-cost among technologies. It is necessary to win the fight with time so that no ground water is contaminated. We have developed two additional devices to help reduce oil accident of smaller ranges. In the case of such an oil accident, it is necessary to carry out the permeability test of contaminated soil in time and, on this basis, to choose the technology appropriate to the accident - either in-sit biodegradation - at the site of the accident, or on-sit - to remove the soil and biodegrade it on the designated deposits. A special injection drill was developed for in-sit biodegradation, tossing and aeration equipment of the extracted soil was developed for

Flash pyrolysis fuel oil: BIO-POK

Energy Technology Data Exchange (ETDEWEB)

Gust, S. [Neste Oy, Porvoo (Finland)

1995-12-31

Flash pyrolysis oil from Ensyn Tech., Canada and Union Fenosa, Spain was combusted with simple pressure atomisation equipment commonly used with light fuel oils in intermediate size (0.1-1 MW) boilers. With a number of modifications to the combustion system, carbon monoxide (CO) and nitrous oxide (NO{sub x}) could be reduced to acceptable levels: CO < 30 ppm and NO{sub x} < 140 ppm. Particulate emissions which were initially very high (Bacharach 4-5) were reduced (Bach. 2-3) by system changes but are still higher than from light fuel oil (Bach. <1). The modifications to the combustion system were: acid resistant progressive cavity pump, higher oil preheat temperature and higher oil pressure than for light fuel oils, refractory section between burner and boiler warmed up to at least 800 deg C. In addition, it was necessary to store pyrolysis oil samples under inert conditions to prevent oxidation and to rinse nozzles with alcohol after shutdown to prevent coking. The complexity and cost of these system modifications are considered to be too great for current grades of flash pyrolysis oil to be sold as a light fuel oil replacement. Improvements to fuel quality will be necessary. The main improvements are lowering of viscosity and improving of stability

Flash pyrolysis fuel oil: BIO-POK

Energy Technology Data Exchange (ETDEWEB)

Gust, S [Neste Oy, Porvoo (Finland)

1996-12-31

Flash pyrolysis oil from Ensyn Tech., Canada and Union Fenosa, Spain was combusted with simple pressure atomisation equipment commonly used with light fuel oils in intermediate size (0.1-1 MW) boilers. With a number of modifications to the combustion system, carbon monoxide (CO) and nitrous oxide (NO{sub x}) could be reduced to acceptable levels: CO < 30 ppm and NO{sub x} < 140 ppm. Particulate emissions which were initially very high (Bacharach 4-5) were reduced (Bach. 2-3) by system changes but are still higher than from light fuel oil (Bach. <1). The modifications to the combustion system were: acid resistant progressive cavity pump, higher oil preheat temperature and higher oil pressure than for light fuel oils, refractory section between burner and boiler warmed up to at least 800 deg C. In addition, it was necessary to store pyrolysis oil samples under inert conditions to prevent oxidation and to rinse nozzles with alcohol after shutdown to prevent coking. The complexity and cost of these system modifications are considered to be too great for current grades of flash pyrolysis oil to be sold as a light fuel oil replacement. Improvements to fuel quality will be necessary. The main improvements are lowering of viscosity and improving of stability

Bioremediation of oil on shorelines with organic and inorganic nutrients

International Nuclear Information System (INIS)

Sveum, P.; Ramstad, S.

1995-01-01

Two experiments to study the mechanisms associated with nutrient-enhanced biodegradation of oil (Statfjord crude oil)-contaminated shorelines were done in continuous-flow seawater exchange basins with simulated tides. The fertilizers included fish and meal pellets, stick water pellets, and two concentrations of Max Bac: standard and five times higher. Both one-time and repeated additions of fish meal were studied. The number of oil-degrading bacteria in the sediment increased by three to four orders of magnitude after adding oil and fertilizer, and repeated fertilization had little effect. Oil degradation was found to be extensive with all treatments in both experiments, which lasted 35 or 98 days. Polycyclic aromatic hydrocarbon degradation seems to be most extensive in the sediments with repeated application of fish meal. The relation between accumulated total soluble nitrogen in interstitial water and nC 17 /pristane differs between the sediments treated with Max Bac and the organic additives, and indicates that this concentration cannot be used as a sole indication of the oil degradation rate if organic nutrients are used. The relation between accumulated CO 2 production and nC 17 /pristane ratio indicates a diauxic use of the two different sources of carbon present, without being absolute. Repeated fertilization with organic additives is neither beneficial nor detrimental to the oil degradation activity

Pyrolysis oil as diesel fuel

Energy Technology Data Exchange (ETDEWEB)

Gros, S [Wartsila Diesel International Ltd., Vaasa (Finland). Diesel Technology

1997-12-31

Wood waste pyrolysis oil is an attractive fuel alternative for diesel engine operation. The main benefit is the sustainability of the fuel. No fossil reserves are consumed. The fact that wood waste pyrolysis oil does not contribute to CO{sub 2} emissions is of utmost importance. This means that power plants utilising pyrolysis oil do not cause additional global warming. Equally important is the reduced sulphur emissions that this fuel alternative implies. The sulphur content of pyrolysis oil is extremely low. The high water content and low heating value are also expected to result in very low NO{sub x} emissions. Utilisation of wood waste pyrolysis oil in diesel engines, however, involves a lot of challenges and problems to be solved. The low heating value requires a new injection system with high capacity. The corrosive characteristics of the fluid also underline the need for new injection equipment materials. Wood waste pyrolysis oil contains solid particles which can clog filters and cause abrasive wear. Wood waste pyrolysis oil has proven to have extremely bad ignition properties. The development of a reliable injection system which is able to cope with such a fuel involves a lot of optimisation tests, redesign and innovative solutions. Successful single-cylinder tests have already been performed and they have verified that diesel operation on wood pyrolysis oil is technically possible. (orig.)

Pyrolysis oil as diesel fuel

Energy Technology Data Exchange (ETDEWEB)

Gros, S. [Wartsila Diesel International Ltd., Vaasa (Finland). Diesel Technology

1996-12-31

Wood waste pyrolysis oil is an attractive fuel alternative for diesel engine operation. The main benefit is the sustainability of the fuel. No fossil reserves are consumed. The fact that wood waste pyrolysis oil does not contribute to CO{sub 2} emissions is of utmost importance. This means that power plants utilising pyrolysis oil do not cause additional global warming. Equally important is the reduced sulphur emissions that this fuel alternative implies. The sulphur content of pyrolysis oil is extremely low. The high water content and low heating value are also expected to result in very low NO{sub x} emissions. Utilisation of wood waste pyrolysis oil in diesel engines, however, involves a lot of challenges and problems to be solved. The low heating value requires a new injection system with high capacity. The corrosive characteristics of the fluid also underline the need for new injection equipment materials. Wood waste pyrolysis oil contains solid particles which can clog filters and cause abrasive wear. Wood waste pyrolysis oil has proven to have extremely bad ignition properties. The development of a reliable injection system which is able to cope with such a fuel involves a lot of optimisation tests, redesign and innovative solutions. Successful single-cylinder tests have already been performed and they have verified that diesel operation on wood pyrolysis oil is technically possible. (orig.)

Analytical Characterization of Butter Oil Enriched with Omega-3 and 6 Fatty Acid Sthrough Chia (Salvia hispanica L. Seed Oil

Directory of Open Access Journals (Sweden)

Muhammad Nadeem

2015-12-01

Full Text Available Analytical characterization of blends of butter oil and chia (Salvia hispanica L. seed oil was performed. Chia oil was added in butter oil at four different levels i.e. 6.25%, 12.5%, 18.75% and 25% (T1, T2, T3 and T4, butter oil without any addition of chia oil served as control. Blends of butter oil and chia oil were packaged in tin containers, stored at ambient temperature (34±2oC for 90-days. Iodine values of control, T1, T2, T3 and T4 were 36.85, 45.63, 57.22, 67.45 and 76.37 (cg/g.Concentration of omega-3 fatty acids in T1, T2, T3 and T4 were 4.17%, 7.39%, 12.55% and 16.74%. The extent of omega-6 fatty acids in T1, T2, T3 and T4 was 2.81%, 2.94%, 3.15% and 3.32%.Concentration of omega-3 and 6 fatty acids in butter oil can be increased by chia oil.

Dispersed oil disrupts microbial pathways in pelagic food webs.

Science.gov (United States)

Ortmann, Alice C; Anders, Jennifer; Shelton, Naomi; Gong, Limin; Moss, Anthony G; Condon, Robert H

2012-01-01

Most of the studies of microbial processes in response to the Deepwater Horizon oil spill focused on the deep water plume, and not on the surface communities. The effects of the crude oil and the application of dispersants on the coastal microbial food web in the northern Gulf of Mexico have not been well characterized even though these regions support much of the fisheries production in the Gulf. A mesocosm experiment was carried out to determine how the microbial community off the coast of Alabama may have responded to the influx of surface oil and dispersants. While the addition of glucose or oil alone resulted in an increase in the biomass of ciliates, suggesting transfer of carbon to higher trophic levels was likely; a different effect was seen in the presence of dispersant. The addition of dispersant or dispersed oil resulted in an increase in the biomass of heterotrophic prokaryotes, but a significant inhibition of ciliates, suggesting a reduction in grazing and decrease in transfer of carbon to higher trophic levels. Similar patterns were observed in two separate experiments with different starting nutrient regimes and microbial communities suggesting that the addition of dispersant and dispersed oil to the northern Gulf of Mexico waters in 2010 may have reduced the flow of carbon to higher trophic levels, leading to a decrease in the production of zooplankton and fish on the Alabama shelf.

Decomposition of PCBs in transformer oil using an electron beam accelerator

International Nuclear Information System (INIS)

Jung, In-Ha; Lee, Myun-Joo; Mah, Yoon-Jung

2012-01-01

Decomposition of PCBs in commercially used transformer oil used for more than 30 years has been carried out at normal temperature and pressure without any additives using an electron beam accelerator. The experiments were carried out in two ways: batch and continuous pilot plant with 1.5 MeV of energy, a 50 mA current, and 75 kW of power in a commercial scale accelerator. The electron beam irradiation seemed to transform large molecular weight compounds into lower ones, but the impact was considered too small on the physical properties of oil. Residual concentrations of PCBs after irradiation depend on the absorption dose of the electron beam energy, but aliphatic chloride compounds were produced at higher doses of irradiation. As the results from FT-NMR, chloride ions decomposed from the PCBs are likely to react with aliphatic hydro carbon compounds rather than existing as free radical ions in the transformer oil. Since this is a dry process, treated oil can be used as cutting oil or machine oil for heavy equipment without any additional treatments. - Highlights: ► We developed a novel technology of decomposing PCBs in transformer oil using an electron beam. ► Distinct feature is accomplishing at ambient temperature and pressure without any additives. ► Residual PCBs were depended on absorption dose, but aliphatic chlorides were produced at higher dose. ► Treated oil can be reused as heating oil with chlorine removal technology developed here.

Influence of oil starvation on piston ring oil film thickness; Junkatsuyu kyokyuryo fusoku ga ring yumaku ni ataeru eikyo

Energy Technology Data Exchange (ETDEWEB)

Hiruma, M [Musashi Institute of Technology, Tokyo (Japan). Hydrogen Energy Research Center; Takiguchi, M [Musashi Institute of Technology, Tokyo (Japan)

1997-10-01

An analytical behavior of the piston ring oil film has been carried out theoretically under the condition where sufficient lubrication oil dose not exist. Phenomena have been studied on the oil film when plural rings slide together on the surface of cylinder with a new concept in addition to the well-known assumptions. In particular, a comparison has been made on the friction force with the data obtained by the floating liner method. 5 refs., 9 figs.

Effectiveness of Biodiesel from Various Tropical Oil Crops on Lubricity Improvement of Ultra Low Sulfur Diesel (ULSD)

Energy Technology Data Exchange (ETDEWEB)

Chollacoop, Nuwong; Topaiboul, Subongkoj; Goodwin, Vituruch (Bioenergy Group, National Metal and Materials Technology Center (MTEC), Thailand Science Park, Pathumthani, 12120 (Thailand)). e-mail: nuwongc@mtec.or.th

2008-10-15

Ultra low sulfur diesel (ULSD) has been introduced worldwide with an aim to reduce emission. Since the desulfurization process for ULSD inadvertently reduces its lubricity, lubricity additive is needed. Biodiesel emerges as a potential candidate due to its excellent lubricity property and little sulfur content. In the present study, biodiesel from various energy crops available in Thailand was added at various amounts to ULSD to test the lubricity according to the CEC-F-06-A-96 standard (using High-Frequency Reciprocating Rig: HFRR [1]). It was found that when biodiesel from crude palm, jatropha, soybean, coconut, sunflower, rice, corn and sesame oils of less than 1% (by volume) is additized to ULSD, the lubricity is improved to meet the diesel standard. Further addition beyond 2% (by volume) does not improve lubricity remarkably, where the lubrication seems to saturate. Biodiesel improves lubricity property by film formation preventing mechanical contact between the rubbing surfaces, and the effectiveness varies among different feedstock oils. Biodiesel from crude palm oil, jatropha oil and coconut oil seemingly are superior lubricity additives in ULSD than that from soybean oil, sunflower oil, rice oil, corn oil and sesame oil. Keywords: biodiesel, bio-lubricants, palm oil, sunflower oil

Storage quality of walnut oil containing lycopene during accelerated oxidation.

Science.gov (United States)

Xie, Chaonan; Ma, Zheng Feei; Li, Fang; Zhang, Hongxia; Kong, Lingming; Yang, Zhipan; Xie, Weifeng

2018-04-01

The purpose of investigation was to assess the effect of lycopene on the peroxide value, acid value, fatty acids, total phenolic content and ferric-reducing antioxidant power of walnut oil. Walnut oil was extracted from Xinjiang walnut variety using cold pressing method. Our study reported that after 45 days of accelerated oxidation at 60 °C (Schaal oven test), 0.005% lycopene exhibited the greatest antioxidant effect than other addition levels of lycopene. Therefore, under ambient storage conditions, the shelf-life of walnut oil could be extended up to 16 months by 0.005% lycopene. Moreover, 0.005% lycopene added to walnut oil had a significantly higher content of saturated fatty acid, unsaturated fatty acid, total phenol, reducing ability of the polar and non-polar components than the blank sample (walnut oil without any addition of lycopene). In conclusion, lycopene improved the quality of walnut oil because of its antioxidant effect against lipid oxidation.

Design and verification of additional filtration for the application of ecological transmission and hydraulic fluids in tractorc

Directory of Open Access Journals (Sweden)

Pavel Máchal

2013-01-01

Full Text Available This contribution presents the design and function verification of additional filtration. It is intended for the common transmission and hydraulic oil filling of tractors. The main role of this filtration concept is to ensure a high level of oil cleanness as a condition for the application of ecologic fluids in tractors. The next one is to decrease the wear of lubricated tractor components, the degradation of oil and eventually to extend the interval of oil change. The designed additional filtering is characterized by ease installation through the use of quick couplings and hoses to the external hydraulic circuit. Therefore, the filtration is suitable for various tractor types. Filter element has been designed with the filter ability 1micron and the ability to separate to 0.5 dm3 of water from oil. Function of additional filtration was verified during the 150 engine hours of tractor operation. During this time period the oil contamination was evaluated on the basis of chemical elements content such as Fe, Cu, Si, Al, Ni, Mo and Cr. The additive concentration was evaluated on the basis of chemical elements content such as Ca, P and Zn. During the test operation of tractor the concentration decrease of chemical elements reached the values 25.53 % (Fe, 23.53 % (Si, 25 % (Al and 5.5 % (Cu. The decrease of additive concentration reached only medium level (6.6 %. Therefore, the designed additional filtration doesn’t remove additives from oil. Based on the evaluation of the content of chemical elements (that representing contamination and additives, we can say that the designed filtering method is suitable for use in agricultural tractors.

Use of an additive in biofuel to evaluate emissions, engine component wear and lubrication characteristics

International Nuclear Information System (INIS)

Kalam, M.A.; Majsuki, H.H.

2003-01-01

This paper presents the results of experiments carried out to evaluate the effect of adding an anticorrosion additive to blended biofuel and lubricating oil on emissions, engine component wear and lubrication characteristics. The blended biofuels consist of 7.5 and 15 per cent palm olein (PO) with ordinary diesel oil (OD). Pure OD was used for comparison purposes. Exhaust emission gases such as NO x , CO and hydrocarbons (HCs) were measured by an exhaust emission analyser for engine operation on 50 per cent throttle at speeds of 800-3600 r/min. To measure engine component wear and lubricating oil characteristics, the engine was operated at 50 per cent throttle at a speed of 2000 r/min for a period of 100 h with each of the fuel samples. The same lubricating oil, conventional SAE 40, was used in all the fuels. A multielement oil analyser (MOA) was used to measure the increase in wear of metals (Fe, Cu, Al, Pd) and the decrease in lubricating oil additives (Zn, Ca) in the lubricating oil used. An ISL automatic Houillon viscometer (ASTM D445) and potentiometric titration (ASTM D2896) were used to measure viscosity and total base number (TBN) respectively. The results show that the addition of anticorrosion additive with biofuel and lubricating oil improves the emission and engine wear characteristics; both the exhaust emission gases (NO x , CO and HCs) and the wear of metals (Fe, Cu, Al and Pd) decrease with the blended fuels in comparison with the base fuel OD. Detailed results, including engine brake power, are discussed. (Author)

Microbial inoculants and fertilization for bioremediation of oil in wetlands

International Nuclear Information System (INIS)

Neralla, S.; Wright, A.L.; Weaver, R.W.

1995-01-01

Bioremediation is an attractive alternative to physical methods of oil spill cleanup in wetlands where the ecosystem can be easily damaged. Because populations of oil-degrading microorganisms are usually low in wetlands, there is potential for increasing bioremediation through bioaugmentation in conjunction with N and P supplementation. Eight microbial inoculant products were added to microcosms containing soil from a salt marsh. Four of these products were also used in mesocosms containing Spartina alterniflora grown in a glasshouse. In unfertilized microcosms, the extent of oil degraded as measured by carbon dioxide evolution during 90 days, was 30% higher in the product with the highest activity than was recorded in the control with oil by 36%. None of the products when added to the fertilized soil increased activity above that of the fertilized control with oil. Addition of oil to microcosms increased populations of hydrocarbon-degrading microorganisms, but bioaugmentation products did not increase populations. Neither addition of products nor fertilization enhanced the disappearance of oil in mesocosms in the glasshouse. Approximately 50% of the weathered oil disappeared in 41 d for all treatments. Because bioaugmentation did not enhance oil degradation, it seems that natural populations of hydrocarbon-degrading microorganisms were adequate in the salt marsh soil for bioremediation

Fuel properties of biodiesel from vegetable oils and oil mixtures. Influence of methyl esters distribution

International Nuclear Information System (INIS)

Martínez, G.; Sánchez, N.; Encinar, J.M.; González, J.F.

2014-01-01

In this work, the quality of biodiesel produced by basic transesterification from several vegetable oils (soybean, rapeseed, sunflower, high oleic sunflower, Cynara Cardunculus L., Brassica Carinata and Jatropha Curca) cultivated in Extremadura has been studied in detail. The influence of raw material composition on properties such as density, viscosity, cetane number, higher heating value, iodine and saponification values and cold filter plugging point has been verified. Other biodiesel properties such as acid value, water content and flash and combustion points were more dependent on characteristics of production process. Biodiesel produced by rapeseed, sunflower and high oleic sunflower oils transesterification have been biofuels with better properties according to Norm EN 14214. Finally, it has been tested that it is possible to use oils mixtures in biodiesel production in order to improve the biodiesel quality. In addition, with the same process conditions and knowing properties of biodiesel from pure oils; for biodiesel from oils mixtures, its methyl esters content, and therefore properties dependent this content can be predicted from a simple mathematical equation proposed in this work. - Highlights: • Biodiesel quality produced by basic transesterification from vegetable oils. • We examine influences of methyl esters distribution on biodiesel properties. • Biofuels from soybean, sunflower and rapeseed oils were with better properties. • Oils mixtures improve biodiesel quality to fulfill Norm EN 14214. • An equation to predict properties of biodiesel from oil mixtures is proposed

Aminodisulfides as additives to lubricants

Energy Technology Data Exchange (ETDEWEB)

Balin, A.I.; Tarasevich, V.B.; Veretenova, T.N.

1980-01-01

A study was carried out and tehcnology developed for producing sulfur-nitrogen containing additives of the type of aminodisulfide by interaction of beta, beta-dichlordialkyl (aryl) disulfides with diethanolamine in a medium of sulfur-diethanolamine. The 2,2'-bis-(diethanol)-dialkyl(aryl) disulfides obtained do not hydrolyze in aqueous soltuions of alkalis, exhibit rather high antiscoring properties and are recommended for tests as active additives of high pressure to SOZH and technological lubricants of the oil and emulsion types.

Compositional Shift in Fatty Acid Profiles of Lipids Obtained from Oleaginous Yeasts upon the Addition of Essential Oil from Citrus sinensis L.

Science.gov (United States)

Uprety, Bijaya K; Rakshit, Sudip K

2017-12-01

Tailoring lipids from oleaginous yeasts to contain specific types of fatty acid is of considerable interest to food, fuel, and pharmaceutical industries. In this study, the essential oil obtained from Citrus sinesus L. has been used to alter the fatty acid composition of two common oleaginous yeasts, Rhodosporidium toruloides and Cryptococcus curvatus. With increasing levels of essential oil in the medium, the metabolic flux of the fatty acid biosynthesis pathway shifted towards saturated fatty acid production. Essential oil reduced the activities of elongase and ∆9 desaturase. This made the lipid obtained from both these yeasts rich in saturated fatty acids. At certain specific concentrations of the essential oil in the medium, the lipid obtained from R. toruloides and C. curvatus cultures was similar to mahuwa butter and palm oil, respectively. Limonene is the major constituents of orange essential oil. Its effect on one of the oleaginous yeasts, R. toruloides, was also studied separately. Effects similar to orange essential oil were obtained with limonene. Thus, we can conclude that limonene in orange essential oil brings about compositional change of microbial lipid produced in this organism.

Developing new markets for oil sands products

International Nuclear Information System (INIS)

Crandall, G.

2004-01-01

This paper presents a review by Purvin and Gertz of western Canadian crude oil supply. This energy consulting firm provides advise to the energy sector. It suggests that oil sands production will surpass declining conventional production. Oil sands supply includes bitumen, synthetic crude oil (SCO), and diluent. It is forecasted that oil sands will increase from 42 per cent of western supply in 2002 to 78 per cent in 2015. The potential of Alberta's oil sands was discussed along with a recent study of refined products and petrochemicals from bitumen. Upgrading, refining and petrochemical case studies were presented. The author examined if a Canadian oil sands upgrading project with high capital costs can be competitive with competing projects in the United States and internationally. In addition to supply and demand issues, the presentation examined infrastructure capability and market potential in the United States. The economic potential and risks of preferred business cases compared to upgrading to SCO were also evaluated. 15 figs

Extracting oils

Energy Technology Data Exchange (ETDEWEB)

Patart, G

1926-03-15

In the hydrogenation or extraction of by-products from organic substances at high temperatures and pressures, the gases or liquids, or both, used are those which are already heated and compressed during industrial operations such as exothermic synthesizing reactions such as the production of methanol from hydrogen and carbon monoxide in a catalytic process. Gases from this reaction may be passed upwardly through a digester packed with pine wood while liquid from the same catalytic process is passed downwardly through the material. The issuing liquid contains methanol, pine oil, acetone, isopropyl alcohol, and acetic acid. The gases contain additional hydrogen, carbon monoxide, methane, ethylene, and its homologs which are condensed upon the catalyser to liquid hydrocarbons. Petroleum oils and coal may be treated similarly.

Analysis of ZDDP Content and Thermal Decomposition in Motor Oils Using NAA and NMR

Science.gov (United States)

Ferguson, S.; Johnson, J.; Gonzales, D.; Hobbs, C.; Allen, C.; Williams, S.

Zinc dialkyldithiophosphates (ZDDPs) are one of the most common anti-wear additives present in commercially-available motor oils. The ZDDP concentrations of motor oils are most commonly determined using inductively coupled plasma atomic emission spectroscopy (ICP-AES). As part of an undergraduate research project, we have determined the Zn concentrations of eight commercially-available motor oils and one oil additive using neutron activation analysis (NAA), which has potential for greater accuracy and less sensitivity to matrix effects as compared to ICP-AES. The 31P nuclear magnetic resonance (31P-NMR) spectra were also obtained for several oil additive samples which have been heated to various temperatures in order to study the thermal decomposition of ZDDPs.

Offshore oil exploration and impact assessment in Greenland

DEFF Research Database (Denmark)

Hansen, Anne Merrild

2016-01-01

Greenland needs development. Oil and mineral extraction is pursued as a means to achieve economical growth. Fisheries, hunting and tourism are the main pillars in the Greenland economy in 2015. These businesses are however sensitive to potential negative impacts from oil and gas development. Local...... regulation system in relation to oil and gas projects to promote sustainable development. Additional Impact Benefit Agreements (IBA) have to be negotiated between the communities potentially affected, the Government and the oil companies to assure that social investments are made to secure long-term benefits...

Forecasting ability of the investor sentiment endurance index: The case of oil service stock returns and crude oil prices

International Nuclear Information System (INIS)

He, Ling T.; Casey, K.M.

2015-01-01

Using a binomial probability distribution model this paper creates an endurance index of oil service investor sentiment. The index reflects the probability of the high or low stock price being the close price for the PHLX Oil Service Sector Index. Results of this study reveal the substantial forecasting ability of the sentiment endurance index. Monthly and quarterly rolling forecasts of returns of oil service stocks have an overall accuracy as high as 52% to 57%. In addition, the index shows decent forecasting ability on changes in crude oil prices, especially, WTI prices. The accuracy of 6-quarter rolling forecasts is 55%. The sentiment endurance index, along with the procedure of true forecasting and accuracy ratio, applied in this study provides investors and analysts of oil service sector stocks and crude oil prices as well as energy policy-makers with effective analytical tools

The Security Impact of Oil Nationalization: Alternate Futures Scenarios

Directory of Open Access Journals (Sweden)

Peter Johnston

2010-01-01

Full Text Available This article highlights the security impact of oil nationalization, develops and analyzes four energy security scenarios, and suggests options to reduce the potential negative impact of oil nationalization. In addition to the use of oil as a weapon, nationalization of oil can also lead to competition for scarce resources among states, facilitate the funding of terrorists or insurgents, contribute to destabilizing regional arms races, influence intra-state conflict, and sustain antagonistic political agendas.

Oil Price Forecasting Using Crack Spread Futures and Oil Exchange Traded Funds

Directory of Open Access Journals (Sweden)

Hankyeung Choi

2015-04-01

Full Text Available Given the emerging consensus from previous studies that crude oil and refined product (as well as crack spread prices are cointegrated, this study examines the link between the crude oil spot and crack spread derivatives markets. Specifically, the usefulness of the two crack spread derivatives products (namely, crack spread futures and the ETF crack spread for modeling and forecasting daily OPEC crude oil spot prices is evaluated. Based on the results of a structural break test, the sample is divided into pre-crisis, crisis, and post-crisis periods. We find a unidirectional relationship from the two crack spread derivatives markets to the crude oil spot market during the post-crisis period. In terms of forecasting performance, the forecasting models based on crack spread futures and the ETF crack spread outperform the Random Walk Model (RWM, both in-sample and out-of-sample. In addition, on average, the results suggest that information from the ETF crack spread market contributes more to the forecasting models than information from the crack spread futures market.

Cryo-FIB SEM for Characterization of the Structure of Fish Oil Emulsions

DEFF Research Database (Denmark)

Jensen, Louise Helene Søgaard; Horn, Anna Frisenfeldt; Jacobsen, Charlotte

2011-01-01

Addition of fish oil to food products to improve nutritional quality by the addition of omega-3 fatty acids is attractive both to the consumers and the food industry for reasons such as health benefits and added product value. The long chain omega-3 fatty acids contain a large number of double...... bonds which causes the fish oil to be susceptible to oxidation. The shelf lives of fish oil enriched products are thus limited by fast oxidation rates of the fish oil which causes development of off flavours as well as degeneration of the beneficial health effects of the fish oil. At the present moment...... this is a barrier for their access to the market and it is necessary to develop techniques to protect the oil against oxidation. Emulsification of the oil has been put forward as a strategy for protection against oxidation, but whether that is beneficial seems to depend on the food matrix to which the oil is added...

Metal working oils. Cutting oils, rolling oils, quenching oils, rust preventive oils; Kinzoku kakoyu. Sessakuyu, atsuenyu, yakiireyu, boseiyu

Energy Technology Data Exchange (ETDEWEB)

Koyama, S. [Idemitsu Kosan Co. Ltd., Tokyo (Japan)

1996-04-01

With the demand against complicating working techniques for a background, foundations of the consideration for each of the lubricants in future are outlined. 1. Cutting oils: From the standpoint of speeding up and fireproofing, share of water-soluble type has come up to 30-40%. In this type, emulsifying dispersants and preservatives are combined. 2. Rolling oils: According to thinning of the standard thickness of steel plates, pressure of contacting surfaces has come up to 300 kg/mm{sup 2}(max.) and slip speed has increased too. In stainless steel plates, in order to get rid of the heat-streak (baking streak originated from wearing-out of oil film) shifting from neat oil to emulsion type is required. 3. Quenching oils: Following two systems are recent tendencies, the mineral oil system having excellent thermostability or the water system containing polyalkylneglycol etc., but the latter is expected from the viewpoint of fireproofing. 4. Rust preventive oils: As this oils do not aim at the rust prevention for long term, degreasing property is required. 20 refs., 5 figs., 1 tab.

Report of the work-group on oil price volatility

International Nuclear Information System (INIS)

2010-01-01

This report proposes a detailed analysis of the past and possible evolution of oil markets in terms of price volatility, financial strategies and pricing. It discusses current reflections and actions aiming at improving oil market operation: the Joint Oil Data Initiative or JODI for oil data transparency, the works of the International Energy Forum (IEF), and the conceivable reforms of the oil financial markets. Then, it proposes and discusses four main strategic orientations for a better knowledge of oil markets by France and the improvement of their operation and transparency: to support IEF initiatives, to apply to oil financial markets the global orientations defined by the G20, to set additional specific rules, and to propose a true oil strategy for the European Union. These orientations are then broken up in 22 propositions

Oil analysis in machine diagnostics

Energy Technology Data Exchange (ETDEWEB)

Vaehaeoja, P.

2006-07-01

This study concentrates on developing and tuning various oil analysis methods to meet the requirements of modern industry and environmental analytics. Oil analysis methods form a vital part of techniques used to monitor the condition of machines and may help to improve the overall equipment effectiveness value of a factory in a significant manner. Worm gears are used in various production machines, and their breakdowns may cause significant production losses. Wearing of these gears is relatively difficult to monitor with vibration analysis. Analysis of two indicator metals, copper and iron, may reveal wearing phenomena of worm gears effectively, and savings can be significant. Effective wear metal analysis requires good tools. ICP-OES with kerosene dilution is widely used in wear metal analysis, but purchasing and using of ICP-OES is expensive. A cheaper FAAS technique with similar pre-treatment of oil samples was tested and it proved to be useful especially in analyzing small amounts of samples. The accuracy of FAAS was sufficient for quantitative work in machine diagnostics and waste oil characterization. Solid debris analyses are useful in oil contamination control as well as in detection of wearing mechanisms. Membrane filtration, optical microscopy, SEM and automatic particle counting were applied in analysis of rolling and gear oils. Particle counting is an effective way to detect oil contamination, but in the studied cases even larger particles than those detected in normal ISO classes would be informative. However, membrane filtration and optical microscopy may reveal the wearing machine element exactly. Additives provide oils with desired properties thus they should be monitored intensively. A FTIR method for quantitative analysis of fatty alcohols and fatty acid esters in machinery oils was developed during this work. It has already been used successfully in quantitative and qualitative analysis of machinery oil samples. Various kinds of oils may be

Impact of Expanded North Slope of Alaska Crude Oil Production on Crude Oil Flows in the Contiguous United States

Energy Technology Data Exchange (ETDEWEB)

DeRosa, Sean E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Flanagan, Tatiana Paz [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-05-01

The National Transportation Fuels Model was used to simulate a hypothetical increase in North Slope of Alaska crude oil production. The results show that the magnitude of production utilized depends in part on the ability of crude oil and refined products infrastructure in the contiguous United States to absorb and adjust to the additional supply. Decisions about expanding North Slope production can use the National Transportation Fuels Model take into account the effects on crude oil flows in the contiguous United States.

Review of the rescue, rehabilitation and restoration of oiled seabirds ...

African Journals Online (AJOL)

Review of the rescue, rehabilitation and restoration of oiled seabirds in South Africa, especially African penguins Spheniscus demersus and Cape gannets Morus capensis , 1983–2005. ... In addition, oiling has a long-term negative impact on the breeding productivity and cost of reproduction in de-oiled birds. The primary ...

Mining for oil in Japan. Report No. 89. [Higashiyama

Energy Technology Data Exchange (ETDEWEB)

1947-09-03

Mining for petroleum by underground methods was undertaken in 1940 by the Japanese in the Higashiyama oil field, Niigata Prefecture, as a means of obtaining additional oil from the sands unrecoverable by wells from the surface. The oil is obtained by gravitational drainage through mine openings and is transported through a gathering system, collected in a sump at the bottom of the main shaft and pumped to the surface. Total production of crude oil for the first six years of operation of the Higashiyama mine was 24,914 kiloliters (156,710 barrels). Average production per meter of gallery for the period 1941-46 was 2.69 kiloliters, equivalent to five barrels per foot. Operations were undertaken without careful studies of the residual oil content of the reservoir sands, or a correct understanding of the producing possibilities of the property. Recoveries leave much to be desired for profitable operation. The results achieved, however, appear to have been successful in view of limited natural oil resources and the great need for petroleum products. The work accomplished in pioneering oil-mining in Japan has provided a background of valuable knowledge and experience which will be beneficial in carrying out future mining projects. Other shallow fields, such as Niitsu, Hibiki, and the Takeishi structure present possibilities of applying underground mining methods to recover additional oil.

Influence of Oil on Refrigerant Evaporator Performance

Science.gov (United States)

Kim, Jong-Soo; Nagata, Karsuya; Katsuta, Masafumi; Tomosugi, Hiroyuki; Kikuchi, Kouichiro; Horichi, Toshiaki

In vapor compression refrigeration system using oil-lubricated compressors, some amount of oil is always circulated through the system. Oil circulation can have a significant influence on the evaporator performance of automotive air conditioner which is especially required to cool quickly the car interior after a period standing in the sun. An experimental investigation was carried out an electrically heated horizontal tube to measure local heat transfer coefficients for various flow rates and heat fluxes during forced convection boiling of pure refrigerant R12 and refrigerant-oil mixtures (0-11% oil concentration by weight) and the results were compared with oil free performance. Local heat transfer coefficients increased at the region of low vapor quality by the addition of oil. On the other hand, because the oil-rich liquid film was formed on the heat transfer surface, heat transfer coefficients gradually decreased as the vapor quality became higher. Average heat transfer coefficient reached a maximum at about 4% oil concentration and this trend agreed well with the results of Green and Furse. Previous correlations, using the properties of the refrigerant-oil mixture, could not predict satisfactorily the local heat transfer coefficients data. New correlation modified by oil concentration factor was developed for predicting the corresponding heat transfer coefficient for refrigerant-oil mixture convection boiling. The maximum percent deviation between predicted and measured heat transfer coefficient was within ±30%.

Enhanced biological degradation of crude oil in a Spitsbergen tundra site

International Nuclear Information System (INIS)

Sveum, P.; Faksness, L.-G.

1993-01-01

A series of oil-contaminated tundra plots on Spitsbergen was treated with combinations of five different fertilizer additives. Both organic and mineral nutrient sources were used, alone or in combination. Biological degradation of oil was recorded in all of the plots. The extent of degradation depended on the type of fertilizer added. The local conditions influence oil degradation significantly, as well as the effect of the fertilizer. Urea, SkogAN (a slow releasing fertilizer), and a blend of fish meals all give high degrees of oil degradation. Both the microbial parameters and the total heterotrophic respiration are influenced by the addition of fertilizers. 6 refs., 13 figs., 3 tabs

Effect of peppermint and citronella essential oils on properties of fish skin gelatin edible films

Science.gov (United States)

Yanwong, S.; Threepopnatkul, P.

2015-07-01

Fish skin gelatin films incorporated with peppermint and citronella essential oils at difference concentrations (10, 20 and 30% w/w) were prepared by solution casting. Addition of peppermint oil contributed to a significant decrease of tensile strength and Young's modulus, while the percent elongation at break showed an obvious increase except at 30% w/w. On the other hand, addition of citronella oils promoted a great increase of tensile strength and young's modulus, but an intense decrease of the percent elongation at break. At the predetermined content, the film incorporated with citronella oils outperformed the one with peppermint oils in term of water vapor transmission and solubility in water. Thermal properties of gelatin films with citronella oils exhibited an enhancement in heat stability, while the one with peppermint oils showed slight decrease in heat stability. The additions with both of essential oils exhibited excellent antibacterial properties against both Staphylococcus aureus and Escherichia coli.

Jojoba oil: A state of the art review and future prospects

International Nuclear Information System (INIS)

Sánchez, Marcos; Avhad, Mangesh R.; Marchetti, Jorge M.; Martínez, Mercedes; Aracil, José

2016-01-01

Highlights: • Jojoba oil is a unique oil formed by long esters instead of triglycerides. • Jojoba cake is gaining interest because of the extraction of valuable chemicals. • Jojoba oil heterogeneous-catalyzed methanolysis makes the process more profitable. - Abstract: Jojoba oil, which is derived from the extraction of Jojoba seed, has a peculiar molecular structure in comparison with the rest of conventional oils. Jojoba oil is formed by long monounsaturated esters whereas the rest of the oils are usually composed by triglycerides. This unconventional structure confers to Jojoba oil unique properties and characteristics that are very valuable for fine chemical industry and for the production of pharmaceuticals. In addition, Jojoba oil can be an excellent source of fatty acid alkyl esters or biodiesel after the transesterification process and the purification steps. This review presents general information about the production of Jojoba oil and its derivatives, its composition, oil extraction process and the applications of this oil when it is used directly or after chemical transformation as well as the possible purposes of Jojoba meal after extraction. In addition, this paper contemplates the advantages and disadvantages of the use of homogeneous and heterogeneous catalysts for the Jojoba oil transesterification as well as different methods to obtain long monounsaturated alcohols, which have pharmaceutical applications, after being separated from biodiesel. The properties of the products derived from the transesterification of Jojoba oil are broadly discussed. Moreover, this review suggests future research opportunities such as a possible biorefinery using Jojoba oil as main raw material, supercritical methods and simultaneous extraction/reaction process which are fully discussed.

Diversification of Oil and Gas Companies’ Activities in the Condition of Oil Prices Reduction and Economic Sanctions

Directory of Open Access Journals (Sweden)

Anastasia V. Sheveleva

2016-01-01

Full Text Available This article analyzes the influence of the economic sanctions imposed from the USA and the EU and oil prices reduction on the oil and gas companies and the directions of diversification of their activity as a method of management of price risks are considered. In the modern dynamic and quickly developing world, in the conditions of globalization and market economy, the oil and gas companies are affected by various risks which can exert negative impact on production and financial results. Risks can arise in absolutely various spheres, beginning from natural and technological hazards, and finishing with price risks. Sharp reduction of oil prices and decrease in demand for energy resources in the world markets, first of all in the European countries, input of financial or technological sanctions from the USA and Europe against Russia in 2014 has caused necessity of search a new more effective methods of price risks management of the oil and gas company. The methods of price risk management include the creation of commodity reserves, the establishment of a reserve fund, long-term contracts, subsidies from the state and the diversification of activities. The most effective it is possible to offer diversification of oil and gas companies' activity. It is expedient to carry out diversification of oil and gas companies' activity in such directions as geographical diversification of the oil, oil products and gas realization directions, geographical diversification of oil and gas companies' purchasing activity, diversification of oil, oil products and gas transportation ways, diversification of oil and gas companies' business. This approach allows to expand the activities of the oil and gas companies and create additional ways to generate revenue and enhance efficiency of oil and gas companies.

Down-hole catalytic upgrading of heavy crude oil

Energy Technology Data Exchange (ETDEWEB)

Weissman, J.G.; Kessler, R.V.; Sawicki, R.A.; Belgrave, J.D.M.; Laureshen, C.J.; Mehta, S.A.; Moore, R.G.; Ursenbach, M.G. [University of Calgary, Calgary, AB (Canada). Dept. of Chemical and Petroleum Engineering

1996-07-01

Several processing options have been developed to accomplish near-well bore in-situ upgrading of heavy crude oils. These processes are designed to pass oil over a fixed bed of catalyst prior to entering the production well, the catalyst being placed by conventional gravel pack methods. The presence of brine and the need to provide heat and reactant gases in a down-hole environment provide challenges not present in conventional processing. These issues were addressed and the processes demonstrated by use of a modified combustion tube apparatus. Middle-Eastern heavy crude oil and the corresponding brine were used at the appropriate reservoir conditions. In-situ combustion was used to generate reactive gases and to drive fluids over a heated sand or catalysts bed, simulating the catalyst contacting portion of the proposed processes. The heavy crude oil was found to be amenable to in-situ combustion at anticipated reservoir conditions, with a relatively low air requirement. Forcing the oil to flow over a heated zone prior to production results in some upgrading of the oil, as compared to the original oil, due to thermal effects. Passing the oil over a hydroprocessing catalyst located in the heated zone results in a product that is significantly upgraded as compared to either the original oil or thermally processed oil. Catalytic upgrading is due to hydrogenation and the results in about a 50% sulfur removal and an 8{degree} API gravity increase. Additionally, the heated catalyst was found to be efficient at converting CO to additional H{sub 2}. While all of the technologies needed for a successful field trial of in-situ catalytic upgrading exist, a demonstration has yet to be undertaken. 27 refs., 5 figs., 5 tabs.

Formation of the oil composition of the Yu0 Bazhenov formation, Salym oil field

Directory of Open Access Journals (Sweden)

E.V. Soboleva

2017-05-01

Full Text Available The Bazhenov horizon of Western Siberia has been studied in considerable detail from different perspectives and different methods, a large number of studies have been devoted to a wide range of issues related to the lithological composition of rocks, their reservoir properties, the study of organic matter, properties and composition of oil at various analytical levels, and many others. This work is devoted to restoring conditions for the formation of oil properties and composition of the Yu0 Salym oil field, based mainly on the geochemical aspects of the study of oil changes both in area and in the section within the productive layer of Salym structure, using some geological data, such as structural plan for the reflecting horizon B (the roof of the Bazhenov formation, having a complex configuration, reservoir temperatures and pressure, well flow rates, and others. There is no single reservoir at the Salym field in the Yu0 formation. For the conclusions of the geological-geochemical interpretation, a sampling of 61 samples of oil from exploration, appraisal and production wells of the initial stages of production was used, since in the future when oil is extracted, the ecology in the deposits changes, and 21 samples of oil from other fields in the West Siberian oil and gas basin. Conventionally, three types of oils are distinguished, differing in their physicochemical parameters, group hydrocarbon and molecular composition. It was suggested that in addition to the own organic matter of the Bazhenov formation, hydrocarbon fluids of the Vasyugan, Tyumen formations and possibly Paleozoic rocks were involved in the formation of the oil composition. The flow of light liquid hydrocarbons and gases occurred along the zones of faults of different genesis and duration of existence.