Periodic inspection of CANDU nuclear power plant containment components

International Nuclear Information System (INIS)

1989-09-01

This Standard is one in a series intended to provide uniform requirements for CANDU nuclear power plants. It provides requirements for the periodic inspection of containment components including the containment pressure suppression systems

Summary of component reliability data for probabilistic safety analysis of Korean standard nuclear power plant

International Nuclear Information System (INIS)

Choi, S. Y.; Han, S. H.

2004-01-01

The reliability data of Korean NPP that reflects the plant specific characteristics is necessary for PSA of Korean nuclear power plants. We have performed a study to develop the component reliability DB and S/W for component reliability analysis. Based on the system, we had have collected the component operation data and failure/repair data during plant operation data to 1998/2000 for YGN 3,4/UCN 3,4 respectively. Recently, we have upgraded the database by collecting additional data by 2002 for Korean standard nuclear power plants and performed component reliability analysis and Bayesian analysis again. In this paper, we supply the summary of component reliability data for probabilistic safety analysis of Korean standard nuclear power plant and describe the plant specific characteristics compared to the generic data

Polyphophoinositides components of plant nuclear membranes

International Nuclear Information System (INIS)

Hendrix, K.W.; Boss, W.F.

1987-01-01

The polyphosphoinositides, phosphatidylinositol monophosphate (PIP) and phosphatidylinositol bisphosphate (PIP 2 ), have been shown to be important components in signal transduction in many animal cells. Recently, these lipids have been found to be associated with plasma membrane but not microsomal membrane isolated from fusogenic wild carrot cells; however, in that study the lipids of the nuclear membrane were not analyzed. Since polyphosphoinositides had been shown to be associated with the nuclear membranes as well as the plasma membrane in some animal cells, it was important to determine whether they were associated with plant nuclear membranes as well. Cells were labeled for 18h with [ 3 H] inositol and the nuclei were isolated by a modification of the procedure of Saxena et al. Preliminary lipid analyses indicate lower amount of PIP and PIP 2 in nuclear membranes compared to whole protoplasts. This suggests that the nuclear membranes of carrot cells are not enriched in PIP and PIP 2 ; however, the Triton X-100 used during the nuclear isolation procedure may have affected the recovery of the lipids. Experiments are in progress to determine the effects of Triton X-100 on lipid extraction

A methodology for on-line fatigue life monitoring of Indian nuclear power plant components

International Nuclear Information System (INIS)

Mukhopadhyay, N.K.; Dutta, B.K.; Kushawaha, H.S.

1992-01-01

Fatigue is one of the most important aging effects of nuclear power plant components. Information about accumulation of fatigue helps in assessing structural degradation of the components. This assists in-service inspection and maintenance and may also support future life extension program of a plant. In the present report a methodology is being proposed for monitoring on line fatigue life of nuclear power plant components using available plant instrumentations. Major factors affecting fatigue life of a nuclear power plant components are the fluctuations of temperature, pressure and flow rate. Green's function technique is used in on line fatigue monitoring as computation time is much less than finite element method. A code has been developed which computes temperature and stress Green's functions in 2-D and axisymmetric structure by finite element method due to unit change in various fluid parameters. A post processor has also been developed which computes the temperature and stress responses using corresponding Green's functions and actual fluctuation in fluid parameters. In this post processor, the multiple site problem is solved by superimposing single site Green's function technique. It is also shown that Green's function technique is best suited for on line fatigue life monitoring of nuclear power plant components. (author). 6 refs., 43 figs

Application of NUREG/CR-5999 interim fatigue curves to selected nuclear power plant components

International Nuclear Information System (INIS)

Ware, A.G.; Morton, D.K.; Nitzel, M.E.

1995-03-01

Recent test data indicate that the effects of the light water reactor (LWR) environment could significantly reduce the fatigue resistance of materials used in the reactor coolant pressure boundary components of operating nuclear power plants. Argonne National Laboratory has developed interim fatigue curves based on test data simulating LWR conditions, and published them in NUREG/CR-5999. In order to assess the significance of these interim fatigue curves, fatigue evaluations of a sample of the components in the reactor coolant pressure boundary of LWRs were performed. The sample consists of components from facilities designed by each of the four U.S. nuclear steam supply system vendors. For each facility, six locations were studied, including two locations on the reactor pressure vessel. In addition, there are older vintage plants where components of the reactor coolant pressure boundary were designed to codes that did not require an explicit fatigue analysis of the components. In order to assess the fatigue resistance of the older vintage plants, an evaluation was also conducted on selected components of three of these plants. This report discusses the insights gained from the application of the interim fatigue curves to components of seven operating nuclear power plants

Life Cycle Management Managing the Aging of Critical Nuclear Plant Components

International Nuclear Information System (INIS)

Meyer, Theodore A.; Elder, G. Gary; Llovet, Ricardo

2002-01-01

Life Cycle Management is a structured process to manage equipment aging and long-term equipment reliability for nuclear plant Systems, Structures and Components (SSCs). The process enables the identification of effective repair, replace, inspect, test and maintenance activities and the optimal timing of the activities to maximize the economic value to the nuclear plant. This paper will provide an overview of the process and some of the tools that can be used to implement the process for the SSCs deemed critical to plant safety and performance objectives. As nuclear plants strive to reduce costs, extend life and maximize revenue, the LCM process and the supporting tools summarized in this paper can enable development of a long term, cost efficient plan to manage the aging of the plant SSCs. (authors)

Estimation of component failure rates for PSA on nuclear power plants 1982-1997

International Nuclear Information System (INIS)

Kirimoto, Yukihiro; Matsuzaki, Akihiro; Sasaki, Atsushi

2001-01-01

Probabilistic safety assessment (PSA) on nuclear power plants has been studied for many years by the Japanese industry. The PSA methodology has been improved so that PSAs for all commercial LWRs were performed and used to examine for accident management.On the other hand, most data of component failure rates in these PSAs were acquired from U.S. databases. Nuclear Information Center (NIC) of Central Research Institute of Electric Power Industry (CRIEPI) serves utilities by providing safety- , and reliability-related information on operation and maintenance of the nuclear power plants, and by evaluating the plant performance and incident trends. So, NIC started a research study on estimating the major component failure rates at the request of the utilities in 1988. As a result, we estimated the hourly-failure rates of 47 component types and the demand-failure rates of 15 component types. The set of domestic component reliability data from 1982 to 1991 for 34 LWRs has been evaluated by a group of PSA experts in Japan at the Nuclear Safety Research Association (NSRA) in 1995 and 1996, and the evaluation report was issued in March 1997. This document describes the revised component failure rate calculated by our re-estimation on 49 Japanese LWRs from 1982 to 1997. (author)

Nuclear power plant systems, structures and components and their safety classification

International Nuclear Information System (INIS)

2000-01-01

The assurance of a nuclear power plant's safety is based on the reliable functioning of the plant as well as on its appropriate maintenance and operation. To ensure the reliability of operation, special attention shall be paid to the design, manufacturing, commissioning and operation of the plant and its components. To control these functions the nuclear power plant is divided into structural and functional entities, i.e. systems. A systems safety class is determined by its safety significance. Safety class specifies the procedures to be employed in plant design, construction, monitoring and operation. The classification document contains all documentation related to the classification of the nuclear power plant. The principles of safety classification and the procedures pertaining to the classification document are presented in this guide. In the Appendix of the guide, examples of systems most typical of each safety class are given to clarify the safety classification principles

Development of a web-based fatigue life evaluation system for primary components in a nuclear power plant

International Nuclear Information System (INIS)

Seo, Hyong Won; Lee, Sang Min; Choi, Jae Boong; Kim, Young Jin; Choi, Sung Nam; Jang, Ki Sang; Hong, Sung Yull

2004-01-01

A nuclear power plant is composed of a number of primary components. Maintaining the integrity of these components is one of the most critical issues in nuclear industry. In order to maintain the integrity of these primary components, a complicated procedure is required including regular in-service inspection, failure assessment, fracture mechanics analysis, etc. Also, experts in different fields have to co-operate to resolve the integrity issues on the basis of inspection results. This integrity evaluation process usually takes long, and thus, is detrimental for the plant productivity. Therefore, an effective safety evaluation system is essential to manage the integrity issues on a nuclear power plant. In this paper, a web-based fatigue life evaluation system for primary components in nuclear power plant is proposed. This system provides engineering knowledge-based information and concurrent and collaborative working environment through internet, and thus, is expected to raise the efficiency of integrity evaluation procedures on primary components of a nuclear power plant

Development of life evaluation technology for nuclear power plant components

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Jin; Kim, Yun Jae; Choi, Jae Boong [Sungkyunkwan Univ., Seoul (Korea, Republic of)] (and others)

2002-03-15

This project focuses on developing reliable life evaluation technology for nuclear power plant components, and is divided into two parts, development of a life evaluation system for nuclear pressure vessels and evaluation of applicability of emerging technology to operating plants. For the development of life evaluation system for nuclear pressure vessels, the following seven topics are covered in this project: defect assessment method for steam generator tubes, development of fatigue monitoring system, assessment of corroded pipes, domestic round robin analysis for constructing P-T limit curve for RPV, development of probabilistic integrity assessment technique, effect of aging on strength of dissimilar welds, applicability of LBB to cast stainless steel, and development of probabilistic piping fracture mechanics.

An approach to safety problems relating to ageing of nuclear power plant components

International Nuclear Information System (INIS)

Conte, M.; Deletre, G.; Henry, J.Y.; Le Meur, M.

1989-10-01

The safety of nuclear power plants, in France, is discussed. The attention is focused on the ageing phenomena, as a potential cause of the degradation of the systems functional capabilities. The allowance for ageing in design and its importance on safety, are analyzed. The understanding of phenomena relating to ageing and the components surveillance, are considered. As the effective ageing on the components of nuclear power plants is not fully understood, technical improvements and more accurate analysis are required

IR-360 nuclear power plant safety functions and component classification

International Nuclear Information System (INIS)

Yousefpour, F.; Shokri, F.; Soltani, H.

2010-01-01

The IR-360 nuclear power plant as a 2-loop PWR of 360 MWe power generation capacity is under design in MASNA Company. For design of the IR-360 structures, systems and components (SSCs), the codes and standards and their design requirements must be determined. It is a prerequisite to classify the IR-360 safety functions and safety grade of structures, systems and components correctly for selecting and adopting the suitable design codes and standards. This paper refers to the IAEA nuclear safety codes and standards as well as USNRC standard system to determine the IR-360 safety functions and to formulate the principles of the IR-360 component classification in accordance with the safety philosophy and feature of the IR-360. By implementation of defined classification procedures for the IR-360 SSCs, the appropriate design codes and standards are specified. The requirements of specific codes and standards are used in design process of IR-360 SSCs by design engineers of MASNA Company. In this paper, individual determination of the IR-360 safety functions and definition of the classification procedures and roles are presented. Implementation of this work which is described with example ensures the safety and reliability of the IR-360 nuclear power plant.

IR-360 nuclear power plant safety functions and component classification

Energy Technology Data Exchange (ETDEWEB)

Yousefpour, F., E-mail: fyousefpour@snira.co [Management of Nuclear Power Plant Construction Company (MASNA) (Iran, Islamic Republic of); Shokri, F.; Soltani, H. [Management of Nuclear Power Plant Construction Company (MASNA) (Iran, Islamic Republic of)

2010-10-15

The IR-360 nuclear power plant as a 2-loop PWR of 360 MWe power generation capacity is under design in MASNA Company. For design of the IR-360 structures, systems and components (SSCs), the codes and standards and their design requirements must be determined. It is a prerequisite to classify the IR-360 safety functions and safety grade of structures, systems and components correctly for selecting and adopting the suitable design codes and standards. This paper refers to the IAEA nuclear safety codes and standards as well as USNRC standard system to determine the IR-360 safety functions and to formulate the principles of the IR-360 component classification in accordance with the safety philosophy and feature of the IR-360. By implementation of defined classification procedures for the IR-360 SSCs, the appropriate design codes and standards are specified. The requirements of specific codes and standards are used in design process of IR-360 SSCs by design engineers of MASNA Company. In this paper, individual determination of the IR-360 safety functions and definition of the classification procedures and roles are presented. Implementation of this work which is described with example ensures the safety and reliability of the IR-360 nuclear power plant.

Age-Related Degradation of Nuclear Power Plant Structures and Components

International Nuclear Information System (INIS)

Braverman, J.; Chang, T.-Y.; Chokshi, N.; Hofmayer, C.; Morante, R.; Shteyngart, S.

1999-01-01

This paper summarizes and highlights the results of the initial phase of a research project on the assessment of aged and degraded structures and components important to the safe operation of nuclear power plants (NPPs). A review of age-related degradation of structures and passive components at NPPs was performed. Instances of age-related degradation have been collected and reviewed. Data were collected from plant generated documents such as Licensing Event Reports, NRC generic communications, NUREGs and industry reports. Applicable cases of degradation occurrences were reviewed and then entered into a computerized database. The results obtained from the review of degradation occurrences are summarized and discussed. Various trending analyses were performed to identify which structures and components are most affected, whether degradation occurrences are worsening, and what was the most common aging mechanisms. The paper also discusses potential aging issues and degradation-susceptible structures and passive components which would have the greatest impact on plant risk

The safety related aspects of pressure components in nuclear power plants

International Nuclear Information System (INIS)

Lindackers, K.H.

1979-01-01

Over the last two years the safety philosophy for nuclear power plants in the Federal Republic of Germany has changed considerably, as everyone working in the field perceives. The original and appropriate philosophy of risk minimalisation through graduated safety barriers has been more and more replaced by the utopian goal of total prevention of any damage. The reasons for this development are discussed briefly especially regarding pressure components. The very numerous pressure components of a nuclear power station are not all of equal importance with respect to safety. Although considerable efforts have been made, it has not been possible, to date, to achieve an agreement between operators, manufacturers, licensing authorities, independent experts, and other specialists about the safety related classification of the manifold pressure bearing parts in nuclear power stations. The background of this extremely regrettable situation is explained. In the last part of the paper the author suggests a simple and clear safety philosophy for pressure components in nuclear power stations. This philosophy is orientated both on Safety Regulations of the Radiation Protection Decree ('Strahlenschutzverordnung') of the 13th October 1976 and on the Safety Criteria for Nuclear Power Stations from 21st October 1977. Only a simple, clear framework can make a contribution to the further improvement of the already exceptional safety of nuclear facilities and to the removal of obstacles in the licensing procedure which, taken as a whole, tie up skilled personnel to a senseless degree, involve considerable financial expenditure, and have no relevance for the safety of nuclear power plants. (orig.) [de

Development of an integrated database management system to evaluate integrity of flawed components of nuclear power plant

International Nuclear Information System (INIS)

Mun, H. L.; Choi, S. N.; Jang, K. S.; Hong, S. Y.; Choi, J. B.; Kim, Y. J.

2001-01-01

The object of this paper is to develop an NPP-IDBMS(Integrated DataBase Management System for Nuclear Power Plants) for evaluating the integrity of components of nuclear power plant using relational data model. This paper describes the relational data model, structure and development strategy for the proposed NPP-IDBMS. The NPP-IDBMS consists of database, database management system and interface part. The database part consists of plant, shape, operating condition, material properties and stress database, which are required for the integrity evaluation of each component in nuclear power plants. For the development of stress database, an extensive finite element analysis was performed for various components considering operational transients. The developed NPP-IDBMS will provide efficient and accurate way to evaluate the integrity of flawed components

Spain's nuclear components industry

International Nuclear Information System (INIS)

Kaibel, E.

1985-01-01

Spanish industrial participation in supply of components for nuclear power plants has grown steadily over the last fifteen years. The share of Spanish companies in work for the five second generation nuclear power plants increased to 50% of total capital investments. The necessity to maintain Spanish technology and production in the nuclear field is emphasized

Development of web-based integrity evaluation system for primary components in a nuclear power plant

Energy Technology Data Exchange (ETDEWEB)

Lee, S.M.; Kim, J.C.; Choi, J.B.; Kim, Y.J. [SAFE Research Center, Sungkyunkwan Univ., Suwon (Korea); Choi, S.N.; Jang, K.S.; Hong, S.Y. [Korea Electronic Power Research Inst., Daejeon (Korea)

2004-07-01

A nuclear power plant is composed of a number of primary components. Maintaining the integrity of these components is one of the most critical issues in nuclear industry. In order to maintain the integrity of these primary components, a complicated procedure is required including periodical in-service inspection, failure assessment, fracture mechanics analysis, etc. Also, experts in different fields have to co-operate to resolve the integrity issues on the basis of inspection results. This integrity evaluation process usually takes long, and thus, is detrimental for the plant productivity. Therefore, an effective safety evaluation system is essential to manage integrity issues on a nuclear power plant. In this paper, a web-based integrity evaluation system for primary components in a nuclear power plant is proposed. The proposed system, which is named as WEBIES (web-based integrity evaluation system), has been developed in the form of 3-tier system architecture. The system consists of three servers; application program server, user interface program server and data warehouse server. The application program server includes the defect acceptance analysis module and the fracture mechanics analysis module which are programmed on the basis of ASME sec. XI, appendix A. The data warehouse server provides data for the integrity evaluation including material properties, geometry information, inspection data and stress data. The user interface program server provides information to all co- workers in the field of integrity evaluation. The developed system provides engineering knowledge-based information and concurrent and collaborative working environment through internet, and thus, is expected to raise the efficiency of integrity evaluation procedures on primary components of a nuclear power plant. (orig.)

Development of web-based integrity evaluation system for primary components in a nuclear power plant

International Nuclear Information System (INIS)

Lee, S.M.; Kim, J.C.; Choi, J.B.; Kim, Y.J.; Choi, S.N.; Jang, K.S.; Hong, S.Y.

2004-01-01

A nuclear power plant is composed of a number of primary components. Maintaining the integrity of these components is one of the most critical issues in nuclear industry. In order to maintain the integrity of these primary components, a complicated procedure is required including periodical in-service inspection, failure assessment, fracture mechanics analysis, etc. Also, experts in different fields have to co-operate to resolve the integrity issues on the basis of inspection results. This integrity evaluation process usually takes long, and thus, is detrimental for the plant productivity. Therefore, an effective safety evaluation system is essential to manage integrity issues on a nuclear power plant. In this paper, a web-based integrity evaluation system for primary components in a nuclear power plant is proposed. The proposed system, which is named as WEBIES (web-based integrity evaluation system), has been developed in the form of 3-tier system architecture. The system consists of three servers; application program server, user interface program server and data warehouse server. The application program server includes the defect acceptance analysis module and the fracture mechanics analysis module which are programmed on the basis of ASME sec. XI, appendix A. The data warehouse server provides data for the integrity evaluation including material properties, geometry information, inspection data and stress data. The user interface program server provides information to all co- workers in the field of integrity evaluation. The developed system provides engineering knowledge-based information and concurrent and collaborative working environment through internet, and thus, is expected to raise the efficiency of integrity evaluation procedures on primary components of a nuclear power plant. (orig.)

The condition monitoring system of turbine system components for nuclear power plants

International Nuclear Information System (INIS)

Ono, Shigetoshi

2013-01-01

The thermal and nuclear power plants have been imposed a stable supply of electricity. To certainly achieve this, we built the plant condition monitoring system based on the heat and mass balance calculation. If there are some performance changes on the turbine system components of their power plants, the heat and mass balance of the turbine system will change. This system has ability to detect the abnormal signs of their components by finding the changes of the heat and mass balance. Moreover we note that this system is built for steam turbine cycle operating with saturated steam conditions. (author)

Component aging and reliability trends in Loviisa Nuclear Power Plant

International Nuclear Information System (INIS)

Jankala, K.E.; Vaurio, J.K.

1989-01-01

A plant-specific reliability data collection and analysis system has been developed at the Loviisa Nuclear Power Plant to perform tests for component aging and analysis of reliability trends. The system yields both mean values an uncertainty distribution information for reliability parameters to be used in the PSA project underway and in living-PSA applications. Several different trend models are included in the reliability analysis system. Simple analytical expressions have been derived from the parameters of these models, and their variances have been obtained using the information matrix. This paper is focused on the details of the learning/aging models and the estimation of their parameters and statistical accuracies. Applications to the historical data of the Loviisa plant are presented. The results indicate both up- and down-trends in failure rates as well as individuality between nominally identical components

Some current engineering topics in nuclear power plant components

International Nuclear Information System (INIS)

Amana, M.

1977-01-01

An analysis based on the principle of fracture mechanics, is presented for several engineering problems occuring in nuclear power plant components. The specific problems covered are: underclad cracking; stress corrosion cracking; cracks in HAZ of nozzle weld; feedwater nozzle corner crack; shift of transition temperature due to neutron irradiation; LWR local-ECC thermal shock experiment; and design and material selection of RPV in terms of fracture mechanics. (B.R.H.)

Nuclear Power Plant Mechanical Component Flooding Fragility Experiments Status

Energy Technology Data Exchange (ETDEWEB)

Pope, C. L. [Idaho State Univ., Pocatello, ID (United States); Savage, B. [Idaho State Univ., Pocatello, ID (United States); Johnson, B. [Idaho State Univ., Pocatello, ID (United States); Muchmore, C. [Idaho State Univ., Pocatello, ID (United States); Nichols, L. [Idaho State Univ., Pocatello, ID (United States); Roberts, G. [Idaho State Univ., Pocatello, ID (United States); Ryan, E. [Idaho State Univ., Pocatello, ID (United States); Suresh, S. [Idaho State Univ., Pocatello, ID (United States); Tahhan, A. [Idaho State Univ., Pocatello, ID (United States); Tuladhar, R. [Idaho State Univ., Pocatello, ID (United States); Wells, A. [Idaho State Univ., Pocatello, ID (United States); Smith, C. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-07-24

This report describes progress on Nuclear Power Plant mechanical component flooding fragility experiments and supporting research. The progress includes execution of full scale fragility experiments using hollow-core doors, design of improvements to the Portal Evaluation Tank, equipment procurement and initial installation of PET improvements, designation of experiments exploiting the improved PET capabilities, fragility mathematical model development, Smoothed Particle Hydrodynamic simulations, wave impact simulation device research, and pipe rupture mechanics research.

Project of mechanical components for nuclear power plants

International Nuclear Information System (INIS)

Amaral, J.A.R. do; Farias Brito David, D. de

1984-01-01

The equipment foreseen to be part of a nuclear power plant must show high quality and safety due to the presence of radioactivity. Besides the perfect functioning during the rigid operating conditions, some postulated loadings are foreseen, like earthquake and loss of coolant accidents, which must be also considered in the design of the components. The design and calculation's concept and development, the interactions with the piping and civil designs, as well as their influences in the licensing process with the authorities are described. (Author) [pt

Ageing study of protection automation components of Olkiluoto nuclear power plant

International Nuclear Information System (INIS)

Simola, K.; Haenninen, S.

1993-07-01

A study on ageing of reactor protection system of the Olkiluoto nuclear power plant is described. The objective of the study was to present an ageing analysis approach and apply in to the automation chains of reactor protection system of the Olkiluoto nuclear power plant. The study includes the measuring instrumentation, the protection logics, and the control electronics of some pumps and valves. The analysis is based on the information collected on the structure of the system, environmental conditions and maintenance practices of components, and operating experience. Based on this information, the possible ageing effects of equipment and their safety significance are evaluated. (orig.). (15 refs., 16 figs., 12 tabs.)

Nuclear Plant Aging Research (NPAR) program plan: Components, systems, and structures

International Nuclear Information System (INIS)

1987-09-01

The nuclear plant aging research described in this plan is intended to resolve issues related to the aging and service wear of equipment and systems and major components at commercial reactor facilities and their possible impact on plant safety. Emphasis has been placed on identification and characterization of the mechanisms of material and component degradation during service and evaluation of methods of inspection, surveillance, condition monitoring, and maintenance as means of mitigating such effects. Specifically, the goals of the program are as follows: (1) to identify and characterize aging and service wear effects which, if unchecked, could cause degradation of equipment, a systems, and major components and thereby impair plant safety; (2) to identify methods of inspection, surveillance, and monitoring, or of evaluating residual life of equipment, systems, and major components, which will ensure timely detection of significant aging effects prior to loss of safety function; and (3) to evaluate the effectiveness of storage, maintenance, repair, and replacement practices in mitigating the rate and extent of degradation caused by aging and service wear

EPRI research on component aging and nuclear plant life extension

International Nuclear Information System (INIS)

Sliter, G.E.; Carey, J.J.

1985-01-01

This paper first describes several research efforts sponsored by the Electric Power Research Institute (EPRI) that examine the aging degradation of organic materials and the nuclear plant equipment in which they appear. This research includes a compendium of material properties characterizing the effects of thermal and radiation aging, shake table testing to evaluate the effects of aging on the seismic performance of electrical components, and a review of condition monitoring techniques applicable to electrical equipment. Also described is a long-term investigation of natural versus artificial aging using reactor buildings as test beds. The paper then describes how the equipment aging research fits into a broad-scoped EPRI program on nuclear plant life extension. The objective of this program is to provide required information, technology, and guidelines to enable utilities to significantly extend operating life beyond the current 40-year licensed term

Application of the Safety Classification of Structures, Systems and Components in Nuclear Power Plants

International Nuclear Information System (INIS)

2016-04-01

This publication describes how to complete tasks associated with every step of the classification methodology set out in IAEA Safety Standards Series No. SSG-30, Safety Classification of Structures, Systems and Components in Nuclear Power Plants. In particular, how to capture all the structures, systems and components (SSCs) of a nuclear power plant to be safety classified. Emphasis is placed on the SSCs that are necessary to limit radiological releases to the public and occupational doses to workers in operational conditions This publication provides information for organizations establishing a comprehensive safety classification of SSCs compliant with IAEA recommendations, and to support regulators in reviewing safety classification submitted by licensees

General requirements for pressure-retaining systems and components in CANDU nuclear power plants

International Nuclear Information System (INIS)

1991-11-01

This standard specifies the general requirements for the design, fabrication and installation of pressure-retaining systems, components, and their supports in CANDU nuclear power plants. (16 figs., 2 tabs., 25 refs.)

Study of a simplified method of evaluating the economic maintenance importance of components in nuclear power plant system

International Nuclear Information System (INIS)

Aoki, Takayuki; Takagi, Toshiyuki; Kodama, Noriko

2014-01-01

Safety risk importance of components in nuclear power plants has been evaluated based on the probabilistic risk assessment and used for the decisions in various plant managements. But economic risk importance of the components has not been discussed very much. Therefore, this paper discusses risk importance of the components from the viewpoint of plant economic efficiency and proposes a simplified evaluation method of the economic risk importance (or economic maintenance importance). As a result of consideration, the followings were obtained. (1) A unit cost of power generation is selected as a performance indicator and can be related to a failure rate of components in nuclear power plant which is a result of maintenance. (2) The economic maintenance importance has to major factors, i.e. repair cost at component failure and production loss associated with plant outage due to component failure. (3) The developed method enables easy understanding of economic impacts of plant shutdown or power reduction due to component failures on the plane which adopts the repair cost in vertical axis and the production loss in horizontal axis. (author)

Service life monitoring of the main components at the Temelin nuclear power plant

International Nuclear Information System (INIS)

Hahn, J.; Vincour, D.

2007-01-01

Knowledge and experience gained from the introduction and periodical implementation of life assessment of the major components of the Temelin nuclear power plant is summarized. The initial Soviet technical design of the plant did not incorporate lifetime monitoring and evaluation, therefore it was completed with demonstrative strength and lifetime calculations from Czech companies. Moreover, a Westinghouse primary circuit diagnosis and monitoring system, including the monitoring of temperature and pressure cycles for low-cycle fatigue evaluation, was installed at the plant. The DIALIFE code for the calculation of mainly the low-cycle fatigue of the key pressure components, was developed and installed subsequently as a superstructure to the monitoring system. (author)

Aging of concrete components and its significance relative to life extension of nuclear power plants

International Nuclear Information System (INIS)

Naus, D.J.

1987-01-01

Nuclear power currently supplies about 16% of the US electricity requirements, with the percentage expected to rise to 20% by 1990. Despite the increasing role of nuclear power in energy production, cessation of orders for new nuclear plants in combination with expiration of operating licenses for several plants in the next 15 to 20 years results in a potential loss of electrical generating capacity of 50 to 60 gigawatts during the time period 2005 to 2020. A potential timely and cost-effective solution to the problem of meeting future energy demand is available through extension of the service life of existing nuclear plants. Any consideration of plant life extension, however, must consider the concrete components in these plants, since they play a vital safety role. Under the USNRC Nuclear Plant Aging Research (NPAR) Program, a study was conducted to review operating experience and to provide background that will lead to subsequent development of a methodology for assessing and predicting the effects of aging on the performance of concrete-based structures. The approach followed was in conformance with the NPAR strategy

Developments of integrity evaluation technology for pressurized components in nuclear power plant and IT based integrity evaluation system

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Jin; Choi, Jae Boong; Shim, Do Jun [Sungkyunkwan Univ., Seoul (Korea, Republic of)] (and others)

2003-03-15

The objective of this research is to develop an efficient evaluation technology and to investigate applicability of newly-developed technology, such as internet-based cyber platform, to operating power plants. Development of efficient evaluation systems for Nuclear Power Plant components, based on structural integrity assessment techniques, are increasingly demanded for safe operation with the increasing operating period of Nuclear Power Plants. The following five topics are covered in this project: development of assessment method for wall-thinned nuclear piping based on pipe test; development of structural integrity program for steam generator tubes with cracks of various shape; development of fatigue life evaluation system for mam components of NPP; development of internet-based cyber platform and integrity program for primary components of NPP; effect of aging on strength of dissimilar welds.

Some experience from seismic check-ups of components of Mochovce nuclear power plant

International Nuclear Information System (INIS)

Masopust, R.

1987-01-01

The first Czechoslovak nuclear power plant with the so-called partial anti-seismic design will be built in Mochovce. The evaluation of seismic resistance is prescribed only for equipment and systems which secure the safe reactor shutdown, the withdrawal of residual heat and prevent uncontrolled release of radioactivity into the environment. The following variants were compared in the calculation analysis of the primary loop of the WWER-440 reactor for the Mochovce nuclear power plant: the seismically unsecured loop of a usual design for WWER-440 nuclear power plants, the loop provided with mechanical or hydraulic dampers and the loop provided with viscose shock absorbers. The tests showed that technically most suitable is the use of viscose shock absorbers which do not completely block the movement of the system during the earthquake but absorb it intensively. The viscose shock absorbers are also much cheaper than the dampers. Briefly described is experience with the experimental evaluation of the seismic resistance of components of the Mochovce nuclear power plant. Great difficulty was encountered by the non-existence in Czechoslovakia of a seismic table allowing simultaneous excitation in the vertical and horizontal directions. (Z.M.). 18 refs

Quality assurance grading criteria for plant systems and components: Results from a pilot plant project at Grand Gulf Nuclear Station. Final report

International Nuclear Information System (INIS)

Parkinson, W.J.

1995-12-01

As part of the original design of a nuclear power plant, the NSSS vendor, architect/engineer and utility identified structures, systems and components (SSCs) as safety related and assigned them to a Q-list. A Q-list is usually very large, e.g. 75,000 components, which creates large ongoing annual operating costs for the utility. Operating experience and the greater knowledge of plant systems safety accumulated during the past 20 years have suggested that many components are not truly important to safety and do not warrant the Q-classification and the associated costs. The completion of Probabilistic Safety Analyses (PSAs) for many nuclear power plants has contributed to this greater knowledge. This report describes a practical application of PSA technology to modify the existing QA program at the Grand Gulf Nuclear Station. Section 1 introduces the term, QA Safety Significant (QASS), and relates it to the existing term, ''safety related''. Section 2 describes six deterministic criteria as a basis for classifying systems as QASS or non-QASS. An expert panel reviewed 421 systems at Grand Gulf Nuclear Station and identified 42 of them as QASS. All components in non-QASS systems are classified as non-QASS. For QASS systems, Section 3 describes five deterministic criteria for classifying components as QASS or non-QASS. By using these two sets of criteria, the expert panel found that the number of components requiring full QA compliance could be reduced by 24%. These results are summarized in Section 4

Interim storage of dismantled nuclear weapon components at the U.S. Department of Energy Pantex Plant

International Nuclear Information System (INIS)

Guidice, S.J.; Inlow, R.O.

1995-01-01

Following the events of 1989 and the subsequent cessation of production of new nuclear weapons by the US, the mission of the Department of Energy (DOE) Nuclear Weapons Complex has shifted from production to dismantlement of retired weapons. The sole site in the US for accomplishing the dismantlement mission is the DOE Pantex Plant near Amarillo, Texas. Pending a national decision on the ultimate storage and disposition of nuclear components form the dismantled weapons, the storage magazines within the Pantex Plant are serving as the interim storage site for pits--the weapon plutonium-bearing component. The DOE has stipulated that Pantex will provide storage for up to 12,000 pits pending a Record of Decision on a comprehensive site-wide Environmental Impact Statement in November 1996

Countermeasure technologies against materials deterioration of nuclear power plant components

International Nuclear Information System (INIS)

2004-09-01

This report was tentative safety standard on countermeasure technologies against materials deterioration of nuclear power plant components issued in 2004 on the base of the testing data obtained until March 2004, which was to be applied for technical evaluation for lifetime management of aged plants and preventive maintenance or repair of neutron irradiated components such as core shrouds and jet pumps. In order to prevent stress corrosion cracks (SCCs) of austenitic stainless steel welds of reactor components, thermal surface modification using laser beams was used on neutron irradiated materials with laser cladding or surface melting process methods by limiting heat input according to amount of accumulated helium so as to prevent crack initiation caused by helium bubble growth and coalescence. Laser cladding method of laser welding using molten sleeve set inside pipe surface to prevent SCCs of nickel-chromium-iron alloy welds, alloy 690 cladding method using tungsten inert gas (TIG) welding to prevent SCCs of nickel-chromium-iron alloy welds for dissimilar joints of pipes, and laser surface solid solution heat treatment method of laser irradiation on surfaces to prevent SCCs of austenitic stainless steel welds were also included as repair technologies. (T. Tanaka)

Predictive based monitoring of nuclear plant component degradation using support vector regression

International Nuclear Information System (INIS)

Agarwal, Vivek; Alamaniotis, Miltiadis; Tsoukalas, Lefteri H.

2015-01-01

Nuclear power plants (NPPs) are large installations comprised of many active and passive assets. Degradation monitoring of all these assets is expensive (labor cost) and highly demanding task. In this paper a framework based on Support Vector Regression (SVR) for online surveillance of critical parameter degradation of NPP components is proposed. In this case, on time replacement or maintenance of components will prevent potential plant malfunctions, and reduce the overall operational cost. In the current work, we apply SVR equipped with a Gaussian kernel function to monitor components. Monitoring includes the one-step-ahead prediction of the component's respective operational quantity using the SVR model, while the SVR model is trained using a set of previous recorded degradation histories of similar components. Predictive capability of the model is evaluated upon arrival of a sensor measurement, which is compared to the component failure threshold. A maintenance decision is based on a fuzzy inference system that utilizes three parameters: (i) prediction evaluation in the previous steps, (ii) predicted value of the current step, (iii) and difference of current predicted value with components failure thresholds. The proposed framework will be tested on turbine blade degradation data.

Design and structural calculation of nuclear power plant mechanical components

International Nuclear Information System (INIS)

Amaral, J.A.R. do

1986-01-01

The mechanical components of a nuclear power plant must show high quality and safety due to the presence of radioactivity. Besides the perfect functioning during the rigid operating conditions, some postulated loadings are foreseen, like earthquake and loss of coolant accidents, which must be also considered in the design. In this paper, it is intended to describe the design and structural calculations concept and development, the interactions with the piping and civil designs, as well as their influences in the licensing process with the authorities. (Author) [pt

Human reliability in non-destructive inspections of nuclear power plant components: modeling and analysis

Energy Technology Data Exchange (ETDEWEB)

Vasconcelos, Vanderley de; Soares, Wellington Antonio; Marques, Raíssa Oliveira; Silva Júnior, Silvério Ferreira da; Raso, Amanda Laureano, E-mail: vasconv@cdtn.br, E-mail: soaresw@cdtn.br, E-mail: raissaomarques@gmail.com, E-mail: silvasf@cdtn.br, E-mail: amandaraso@hotmail.com [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2017-07-01

Non-destructive inspection (NDI) is one of the key elements in ensuring quality of engineering systems and their safe use. NDI is a very complex task, during which the inspectors have to rely on their sensory, perceptual, cognitive, and motor skills. It requires high vigilance once it is often carried out on large components, over a long period of time, and in hostile environments and restriction of workplace. A successful NDI requires careful planning, choice of appropriate NDI methods and inspection procedures, as well as qualified and trained inspection personnel. A failure of NDI to detect critical defects in safety-related components of nuclear power plants, for instance, may lead to catastrophic consequences for workers, public and environment. Therefore, ensuring that NDI methods are reliable and capable of detecting all critical defects is of utmost importance. Despite increased use of automation in NDI, human inspectors, and thus human factors, still play an important role in NDI reliability. Human reliability is the probability of humans conducting specific tasks with satisfactory performance. Many techniques are suitable for modeling and analyzing human reliability in NDI of nuclear power plant components. Among these can be highlighted Failure Modes and Effects Analysis (FMEA) and THERP (Technique for Human Error Rate Prediction). The application of these techniques is illustrated in an example of qualitative and quantitative studies to improve typical NDI of pipe segments of a core cooling system of a nuclear power plant, through acting on human factors issues. (author)

Human reliability in non-destructive inspections of nuclear power plant components: modeling and analysis

International Nuclear Information System (INIS)

Vasconcelos, Vanderley de; Soares, Wellington Antonio; Marques, Raíssa Oliveira; Silva Júnior, Silvério Ferreira da; Raso, Amanda Laureano

2017-01-01

Non-destructive inspection (NDI) is one of the key elements in ensuring quality of engineering systems and their safe use. NDI is a very complex task, during which the inspectors have to rely on their sensory, perceptual, cognitive, and motor skills. It requires high vigilance once it is often carried out on large components, over a long period of time, and in hostile environments and restriction of workplace. A successful NDI requires careful planning, choice of appropriate NDI methods and inspection procedures, as well as qualified and trained inspection personnel. A failure of NDI to detect critical defects in safety-related components of nuclear power plants, for instance, may lead to catastrophic consequences for workers, public and environment. Therefore, ensuring that NDI methods are reliable and capable of detecting all critical defects is of utmost importance. Despite increased use of automation in NDI, human inspectors, and thus human factors, still play an important role in NDI reliability. Human reliability is the probability of humans conducting specific tasks with satisfactory performance. Many techniques are suitable for modeling and analyzing human reliability in NDI of nuclear power plant components. Among these can be highlighted Failure Modes and Effects Analysis (FMEA) and THERP (Technique for Human Error Rate Prediction). The application of these techniques is illustrated in an example of qualitative and quantitative studies to improve typical NDI of pipe segments of a core cooling system of a nuclear power plant, through acting on human factors issues. (author)

The effects of aging on electrical and I ampersand C components: Results of US Nuclear Plant Aging Research

International Nuclear Information System (INIS)

Aggarwal, S.K.; Gunther, W.E.

1993-01-01

The US NRC's hardware oriented engineering research program for plant aging and degradation monitoring has achieved results in the area of electrical, control, and instrumentation (ECI) components used in nuclear power plants (NPPs). The principal goals of the program, known as the Nuclear Power Plant Aging Research (NPAR) Program, are to understand the effects of age-related degradation in NPPs and how to manage and mitigate them effectively. This paper describes how these goals have been achieved for key ECI components used in the safety systems of NPPs. The status of relevant on-going and planned research projects is also provided

The effects of aging on electrical and I ampersand C components: Results of US nuclear plant aging research

International Nuclear Information System (INIS)

Aggarwal, S.K.; Gunther, W.E.

1991-01-01

The US NRC's hardware oriented engineering research program for plant aging and degradation monitoring has achieved results in the area of electrical, control, and instrumentation (ECI) components used in nuclear power plants (NPPs). The principal goals of the program, known as the Nuclear Power Plant Aging Research (NPAR) Program, are to understand the effects of age-related degradation in NPPs and how to manage and mitigate them effectively. This paper describes how these goals have been achieved for key ECI components used in the safety systems of NPPs. The status of relevant on-going and planned research projects is also provided

A study on the optimal replacement periods of digital control computer's components of Wolsung nuclear power plant unit 1

International Nuclear Information System (INIS)

Mok, Jin Il; Seong, Poong Hyun

1993-01-01

Due to the failure of the instrument and control devices of nuclear power plants caused by aging, nuclear power plants occasionally trip. Even a trip of a single nuclear power plant (NPP) causes an extravagant economical loss and deteriorates public acceptance of nuclear power plants. Therefore, the replacement of the instrument and control devices with proper consideration of the aging effect is necessary in order to prevent the inadvertent trip. In this paper we investigated the optimal replacement periods of the control computer's components of Wolsung nuclear power plant Unit 1. We first derived mathematical models of optimal replacement periods to the digital control computer's components of Wolsung NPP Unit 1 and calculated the optimal replacement periods analytically. We compared the periods with the replacement periods currently used at Wolsung NPP Unit 1. The periods used at Wolsung is not based on mathematical analysis, but on empirical knowledge. As a consequence, the optimal replacement periods analytically obtained and those used in the field show a little difference. (Author)

Detection of instrument or component failures in a nuclear plant by Luenberger observers

International Nuclear Information System (INIS)

Wilburn, N.P.; Colley, R.W.; Alexandro, F.J.; Clark, R.N.

1985-01-01

A diagnostic system, which will distinguish between instrument failures (flowmeters, etc.) and component failures (valves, filters, etc.) that show the same symptoms, has been developed for nuclear Plants using Luenberger observers. Luenberger observers are online computer based modules constructed following the technology of Clark [3]. A seventh order model of an FFTF subsystem was constructed using the Advanced Continuous Simulation Language (ACSL) and was used to show through simulation that Luenberger observers can be applied to nuclear systems

Nuclear heat source component design considerations for HTGR process heat reactor plant concept

International Nuclear Information System (INIS)

McDonald, C.F.; Kapich, D.; King, J.H.; Venkatesh, M.C.

1982-05-01

The coupling of a high-temperature gas-cooled reactor (HTGR) and a chemical process facility has the potential for long-term synthetic fuel production (i.e., oil, gasoline, aviation fuel, hydrogen, etc) using coal as the carbon source. Studies are in progress to exploit the high-temperature capability of an advanced HTGR variant for nuclear process heat. The process heat plant discussed in this paper has a 1170-MW(t) reactor as the heat source and the concept is based on indirect reforming, i.e., the high-temperature nuclear thermal energy is transported [via an intermediate heat exchanger (IHX)] to the externally located process plant by a secondary helium transport loop. Emphasis is placed on design considerations for the major nuclear heat source (NHS) components, and discussions are presented for the reactor core, prestressed concrete reactor vessel (PCRV), rotating machinery, and heat exchangers

In-plant reliability data base for nuclear plant components: a feasibility study on human error information

International Nuclear Information System (INIS)

Borkowski, R.J.; Fragola, J.R.; Schurman, D.L.; Johnson, J.W.

1984-03-01

This report documents the procedure and final results of a feasibility study which examined the usefulness of nuclear plant maintenance work requests in the IPRDS as tools for understanding human error and its influence on component failure and repair. Developed in this study were (1) a set of criteria for judging the quality of a plant maintenance record set for studying human error; (2) a scheme for identifying human errors in the maintenance records; and (3) two taxonomies (engineering-based and psychology-based) for categorizing and coding human error-related events

Procedure for the qualification of a manufacturer of ingot iron pieces for application in nuclear power plant components

International Nuclear Information System (INIS)

Rahn, K.M.M.; Jusevicius, E.; Michael, H.

1981-01-01

The process for the qualification of 'Sao Caetano do Sul (Acos Villares S/A)' Plant as manufacturers of ingot iron pieces for application in components of Angra 2 and Angra 3 Nuclear Power Plants, is presented. The qualification was executed by IBQN - Instituto Brasileiro de Qualidade Nuclear - the organ officially in charge of the execution of qualification of suppliers of materials for the nuclear industry. (E.G.) [pt

Safety aspects of nuclear power plant component aging

International Nuclear Information System (INIS)

Conte, M.; Deletre, G.; Henry, J.Y.

1988-01-01

The safety of nuclear plants depends on the capacity of the systems they are composed to perform the functions they were designed for. The identification and understanding of phenomena liable to degrade this operational capacity thus constitute one of the safety problems for which allowance must be made at the earliest stage of a project. Aging, a natural and hence unavoidable process affecting all the components of an installation, was identified at a very early stage as being one of these phenomena. The investigation and implementation of solutions to the safety problems associated to aging make it necessary to: defining the domain in which the consequences of aging are to be evaluated, identifying the parameters involved, identifying the components sensitive to these parameters, understanding the mechanisms which govern its evolution. The results of qualification tests, and of tests and checks carried out at different stages of construction and operation, as well as allowance for operating experience, constitute the necessary basis for establishing or improving the regulatory requirements. The procedures for validating components and systems of the installation are also drawn up on the basis of these tests. Finally, the actions initiated within the scope of research and development programmes supply the additional data necessary for such validation, and provide the indispensable support for knowledge improvement

Progress on Plant-Level Components for Nuclear Fuel Recycling: Commonality

International Nuclear Information System (INIS)

De Almeida, Valmor F.

2011-01-01

Progress made in developing a common mathematical modeling framework for plant-level components of a simulation toolkit for nuclear fuel recycling is summarized. This ongoing work is performed under the DOE Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, which has an element focusing on safeguards and separations (SafeSeps). One goal of this element is to develop a modeling and simulation toolkit for used nuclear fuel recycling. The primary function of the SafeSeps simulation toolkit is to enable the time-dependent coupling of separation modules and safeguards tools (either native or third-party supplied) that simulate and/or monitor the individual separation processes in a separations plant. The toolkit integration environment will offer an interface for the modules to register in the toolkit domain based on the commonality of diverse unit operations. This report discusses the source of this commonality from a combined mathematical modeling and software design perspectives, and it defines the initial basic concepts needed for development of application modules and their integrated form, that is, an application software. A unifying mathematical theory of chemical thermomechanical network transport for physicochemical systems is proposed and outlined as the basis for developing advanced modules. A program for developing this theory from the underlying first-principles continuum thermomechanics will be needed in future developments; accomplishment of this task will enable the development of a modern modeling approach for plant-level models. Rigorous, advanced modeling approaches at the plant-level can only proceed from the development of reduced (or low-order) models based on a solid continuum field theory foundation. Such development will pave the way for future programmatic activities on software verification, simulation validation, and model uncertainty quantification on a scientific basis; currently, no satisfactory foundation exists for

Progress on Plant-Level Components for Nuclear Fuel Recycling: Commonality

Energy Technology Data Exchange (ETDEWEB)

de Almeida, Valmor F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2011-08-15

Progress made in developing a common mathematical modeling framework for plant-level components of a simulation toolkit for nuclear fuel recycling is summarized. This ongoing work is performed under the DOE Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, which has an element focusing on safeguards and separations (SafeSeps). One goal of this element is to develop a modeling and simulation toolkit for used nuclear fuel recycling. The primary function of the SafeSeps simulation toolkit is to enable the time-dependent coupling of separation modules and safeguards tools (either native or third-party supplied) that simulate and/or monitor the individual separation processes in a separations plant. The toolkit integration environment will offer an interface for the modules to register in the toolkit domain based on the commonality of diverse unit operations. This report discusses the source of this commonality from a combined mathematical modeling and software design perspectives, and it defines the initial basic concepts needed for development of application modules and their integrated form, that is, an application software. A unifying mathematical theory of chemical thermomechanical network transport for physicochemical systems is proposed and outlined as the basis for developing advanced modules. A program for developing this theory from the underlying first-principles continuum thermomechanics will be needed in future developments; accomplishment of this task will enable the development of a modern modeling approach for plant-level models. Rigorous, advanced modeling approaches at the plant-level can only proceed from the development of reduced (or low-order) models based on a solid continuum field theory foundation. Such development will pave the way for future programmatic activities on software verification, simulation validation, and model uncertainty quantification on a scientific basis; currently, no satisfactory foundation exists for

Tests of qualification of national components of nuclear power plants under design basis accident

International Nuclear Information System (INIS)

Mesquita, A.Z.

1990-01-01

With the purpose of qualifying national components of nuclear power plants, whose working must be maintained during and after an accident, the Thermohydraulic Division of CDTN have done tests to check the equipment stability, under Design Basis Accident conditions. Until this moment, the following components were tested: electrical junction boxes (connectors); coating systems for wall, inside cover and steel containment; hydraulics components of personnel and equipment airlock. This work describes the test instalation, the tests performed and its results. The components tested, in a general way, fulfil the specified requirements. (author) [pt

Assessment and Management of Ageing of Major Nuclear Power Plant Components Important to Safety: Steam Generators. 2011 Update

International Nuclear Information System (INIS)

2011-11-01

At present there are over four hundred forty operational nuclear power plants (NPPs) in IAEA Member States. Ageing degradation of the systems, structures of components during their operational life must be effectively managed to ensure the availability of design functions throughout the plant service life. From the safety perspective, this means controlling, within acceptable limits, the ageing degradation and wear-out of plant components important to safety so that adequate safety margins remain, i.e. integrity and functional capability in excess of normal operating requirements. This IAEA-TECDOC is one in a series of reports on the assessment and management of ageing of the major NPP components important to safety. The reports are based on experience and practices of NPP operators, regulators, designers, manufacturers, and technical support organizations. The current practices for the assessment of safety margins (fitness for service) and the inspection, monitoring and mitigation of ageing degradation of selected components of Canada deuteriumuranium (CANDU) reactor, boiling water reactor (BWR), pressurized water reactor (PWR), and water moderated, water cooled energy reactor (WWER) plants are documented in the reports. These practices are intended to help all involved directly and indirectly in ensuring the safe operation of NPPs, and also to provide a common technical basis for dialogue between plant operators and regulators when dealing with age related licensing issues. Since the reports are written from a safety perspective, they do not address life or life cycle management of the plant components, which involves the integration of ageing management and economic planning. The target audience of the reports consists of technical experts from NPPs and from regulatory, plant design, manufacturing and technical support organizations dealing with specific plant components addressed in the reports. The component addressed in the present publication is the steam

Conceptual benefits of passive nuclear power plants and their effect on component design

International Nuclear Information System (INIS)

DeVine, J.C. Jr.

1996-01-01

Today, nearly ten years after the advanced light water reactor (ALWR) Program was conceived by US utility leaders, and a decade and a half since a new nuclear power plant was ordered in the US, the ALWR passive plant is coming into its own. This design concept, a midsized simplified light water reactor, features extremely reliable passive systems for accident prevention and mitigation and combines proven experience with state-of-the-art engineering and human factors. It is now emerging as the front runner to become the next generation reactor in the US and perhaps around the world. Although simple and straightforward in concept, the passive plant is in many respects a significant departure from previous trends in reactor engineering. Successful implementation of this concept presents numerous challenges to the designers of passive plant systems and components. This paper provides a brief history of the ALWR program, it outlines the ALWR passive plant design objectives and principles, and it summarizes with examples their implications on component design. (orig.)

Aging effects in PWR power plants components

Energy Technology Data Exchange (ETDEWEB)

Borges, Diogo da S.; Guimaraes, Antonio C.F.; Moreira, Maria de Lourdes, E-mail: diogosb@outlook.com, E-mail: tony@ien.gov.br, E-mail: malu@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

2013-07-01

This paper presents a contribution to the study of aging process of components in commercial plants of Pressurized Water Reactors (PWRs). The analysis is made through application of the Fault Trees Method, Monte Carlo Method and Fussell-Vesely Importance Measure. The approach of the study of aging in nuclear power plants, besides giving attention to the economic factors involved directly with the extent of their operational life, also provide significant data on security issues. The latest case involving process of life extension of a PWR could be seen in Angra 1 Nuclear Power Plant through investing of $27 million for the installation of a new reactor lid. The corrective action has generated an estimated operating life extension of Angra I in twenty years, offering great economy compared with building cost of a new plant and anterior decommissioning, if it had reached the time operating limit of forty years. The Extension of the operating life of a nuclear power plant must be accompanied by a special attention to the components of the systems and their aging process. After the application of the methodology (aging analysis of the injection system of the containment spray) proposed in this work, it can be seen that 'the increase in the rate of component failure, due the aging process, generates the increase in the general unavailability of the system that containing these basic components'. The final results obtained were as expected and may contribute to the maintenance policy, preventing premature aging process in Nuclear Plant Systems. (author)

Lifetime assessment and lifetime management for key components of nuclear power plants

International Nuclear Information System (INIS)

Dou Yikang; Sun Hanhong; Qu Jiadi

2000-01-01

On the bases of investigation on recent development of plant lifetime management in the world, the author gives some points of view on how to establish plant lifetime assessment (PLA) and management (PLM) systems for Chinese nuclear power plants. The main points lie in: 1) safety regulatory organizations, utilities and R and D institutes work cooperatively for PLA and PLM; 2) PLA and PLM make a interdependent cycle, which means that a good PLM system ensures authentic input for PLA, while veritable PLA provides valuable feedback for PLM improvement; 3) PLA and PLM should be initiated for some key components. The author also analyzes some important problems to be tackled in PLA and PLM from the view angle of a R and D institute

Fatigue evaluation including environmental effects for primary circuit components in nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Seichter, Johannes [Siempelkamp Pruef- und Gutachter-Gesellschaft mbH, Dresden (Germany); Reese, Sven H.; Klucke, Dietmar [E.ON Kernkraft GmbH, Hannover (Germany). Component Technology

2013-06-01

The influence of LWR coolant environment to the lifetime of materials in nuclear power plants is being discussed internationally. Environmental phenomena had been investigated in laboratory tests and published in recent years. The discussion is mainly focused both on the transition from laboratory to real plant components and on numerical calculation procedures. Since publishing of the NUREG/CR-6909 report in 2007, formulae for calculating the Fen factors have been modified several times. Various calculation procedures are discussed and recommendations are made how to avoid extremely conservative results. (orig.)

Nuclear Power Plant Lifetime Management Study (I)

Energy Technology Data Exchange (ETDEWEB)

Hong, Sung Yull; Jeong, Ill Seok; Jang, Chang Heui; Song, Taek Ho; Song, Woo Young [Korea Electric Power Research Institute, Taejon (Korea, Republic of); Jin, Tae Eun [Korea Power Engineering Company Consulting and Architecture Engineers, (Korea, Republic of); Kim, Woo Chul [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1997-12-31

As the operation-year of nuclear power plant increases and finding sites for new nuclear power plant becomes harder, a comprehensive and systematic nuclear plant lifetime management(PLIM) program including life extension has to be established for stable and safe supply of electricity. A feasibility study was conducted to systematically evaluate technical, economic and regulatory aspect of plant lifetime managements and plant life extension for Kori-1 nuclear power plant. For technical evaluation of nuclear power plant, 13 major components were selected for lifetime evaluation by screening system. structure, and components(SSCs) of the plant. It was found that except reactor pressure vessel, which needs detailed integrity analysis, and low pressure turbine, which is scheduled to be replaced, 11 out of 13 major components have sufficient service life, for more than 40 years. Because domestic rules and regulations related to license renewal has not yet been written, review on the regulatory aspect of life extensions was conducted using US NRC rules and regulations. A cooperative effort with nuclear regulatory body is needed for early completion of license renewal rules and regulations. For economic evaluation of plant lifetime extension, a computer program was developed and used. It was found that 10 to 20 year of extension operation of Kori-1 nuclear power plant was proved. Based on the results, next phase of plant lifetime management program for detailed lifetime evaluation and presenting detailed implementation schedule for plant refurbishment for lifetime extension should be followed. (author). 74 refs., figs.

Nuclear Power Plant Lifetime Management Study (I)

Energy Technology Data Exchange (ETDEWEB)

Hong, Sung Yull; Jeong, Ill Seok; Jang, Chang Heui; Song, Taek Ho; Song, Woo Young [Korea Electric Power Research Institute, Taejon (Korea, Republic of); Jin, Tae Eun [Korea Power Engineering Company Consulting and Architecture Engineers, (Korea, Republic of); Kim, Woo Chul [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1996-12-31

As the operation-year of nuclear power plant increases and finding sites for new nuclear power plant becomes harder, a comprehensive and systematic nuclear plant lifetime management(PLIM) program including life extension has to be established for stable and safe supply of electricity. A feasibility study was conducted to systematically evaluate technical, economic and regulatory aspect of plant lifetime managements and plant life extension for Kori-1 nuclear power plant. For technical evaluation of nuclear power plant, 13 major components were selected for lifetime evaluation by screening system. structure, and components(SSCs) of the plant. It was found that except reactor pressure vessel, which needs detailed integrity analysis, and low pressure turbine, which is scheduled to be replaced, 11 out of 13 major components have sufficient service life, for more than 40 years. Because domestic rules and regulations related to license renewal has not yet been written, review on the regulatory aspect of life extensions was conducted using US NRC rules and regulations. A cooperative effort with nuclear regulatory body is needed for early completion of license renewal rules and regulations. For economic evaluation of plant lifetime extension, a computer program was developed and used. It was found that 10 to 20 year of extension operation of Kori-1 nuclear power plant was proved. Based on the results, next phase of plant lifetime management program for detailed lifetime evaluation and presenting detailed implementation schedule for plant refurbishment for lifetime extension should be followed. (author). 74 refs., figs.

Experience with nonuniform damping in the seismic analysis of nuclear plant components

International Nuclear Information System (INIS)

Winkel, B.V.; Julyk, L.J.

1983-01-01

Individual components of nuclear power plants may exhibit pronounced differences in damping magnitude. Various methods for accounting for nonuniform damping in a structural model are reviewed and evaluated. The methods are compared by solving a beam/pipe model subjected to a typical seismic ground motion. A two-degree-of-freedom variable damping parameter study is also presented. Based upon the experience of evaluating and applying the available methods, application guidelines are presented

Assessment and management of ageing of major nuclear power plant components important to safety: CANDU reactor assemblies

International Nuclear Information System (INIS)

2001-02-01

At present, there are over four hundred operational nuclear power plants (NPPs) in IAEA Member States. Operating experience has shown that ineffective control of the ageing degradation of the major NPP components (e.g. caused by unanticipated phenomena and by operating, maintenance, design or manufacturing errors) can jeopardize plant safety and also plant life. Ageing in these NPPs must therefore be effectively managed to ensure the availability of design functions throughout the plant service life. From the safety perspective, this means controlling within acceptable limits the ageing degradation and wearout of plant components important to safety so that adequate safety margins remain, i.e. integrity and functional capability in excess of normal operating requirements. This TECDOC is one in a series of reports on the assessment and management of ageing of the major NPP components important to safety. The reports are based on experience and practices of NPP operators, regulators, designers, manufacturers, and technical support organizations and a widely accepted Methodology for the Management of Ageing of NPP Components Important to Safety which was issued by the IAEA in 1992. The current practices for the assessment of safety margins (fitness for service) and the inspection, monitoring, and mitigation of ageing degradation of selected components of Canada deuterium-uranium (CANDU) reactors, boiling water reactors (BWRs), pressurized water reactors (PWRs) including the Soviet designed water moderated and water cooled energy reactors (WWERs), are documented in the reports. These practices are intended to help all involved directly and indirectly in ensuring the safe operation of NPPs and also to provide a common technical basis for dialogue between plant operators and regulators when dealing with age-related licensing issues. Since the reports are written from a safety perspective, they do not address life or life-cycle management of the plant components, which

Nuclear plant aging research program

International Nuclear Information System (INIS)

Eissenberg, D.M.

1987-01-01

The U.S. Nuclear Regulatory Commission, Office of Nuclear Regulatory Research, has established the Nuclear Plant Aging Research (NPAR) program in its Division of Engineering Technology. Principal contractors for this program include Oak Ridge National Laboratory, Brookhaven National Laboratory, Idaho National Engineering Laboratory, and Pacific Northwest Laboratory. The program goals are: to identify and characterize time-dependent degradation (aging) of nuclear plant safety-related electrical and mechanical components which could lead to loss of safety function; to identify and recommend methods for detecting and trending aging effects prior to loss of safety function so that timely maintenance can be implemented; and to recommend maintenance practices for mitigating the effects of aging. Research activities include prioritization of system and component aging in nuclear plants, characterization of aging degradation of specific components including identification of functional indicators useful for trending degradation, and testing of practical methods and devices for measuring the functional indicators. Aging assessments have been completed on electric motors, snubbers, motor-operated valves, and check valves. Testing of trending methods and devices for motor-operated valves and check valves is in progress

Advancements in the design of safety-related systems and components of the MARS nuclear plant

International Nuclear Information System (INIS)

Caira, M.; Caruso, G.; Naviglio, A.; Sorabella, L.; Farello, C.E.

1992-01-01

In the paper, the advancements in the design of safety-related systems and components of the MARS nuclear plant, equipped with a 600 MW th PWR, are described. These advancements are due to the special safety features of this plant, which relies completely on inherent and passive safety. In particular, the new steps of the design of the innovative, completely passive, and with an unlimited autonomy Emergency core Cooling System are described, together with the characteristics of the last version of the steam generator, developed in a new design involving disconnecting components, for a fast erection and an easy maintenance. (author)

Lithuanian requirements for ageing management of systems and components important to safety of nuclear power plant

International Nuclear Information System (INIS)

Ramanauskiene, A.

2000-01-01

In this paper the Lithuanian requirements for ageing management of systems and components important to safety of Ignalina nuclear power plant (two RBMK-1500 water-cooled graphite moderated channel-type power reactors) are presented

Intelligent Component Monitoring for Nuclear Power Plants

International Nuclear Information System (INIS)

Tsoukalas, Lefteri

2010-01-01

Reliability and economy are two major concerns for a nuclear power generation system. Next generation nuclear power reactors are being developed to be more reliable and economic. An effective and efficient surveillance system can generously contribute toward this goal. Recent progress in computer systems and computational tools has made it necessary and possible to upgrade current surveillance/monitoring strategy for better performance. For example, intelligent computing techniques can be applied to develop algorithm that help people better understand the information collected from sensors and thus reduce human error to a new low level. Incidents incurred from human error in nuclear industry are not rare and have been proven costly. The goal of this project is to develop and test an intelligent prognostics methodology for predicting aging effects impacting long-term performance of nuclear components and systems. The approach is particularly suitable for predicting the performance of nuclear reactor systems which have low failure probabilities (e.g., less than 10 -6 year -1 ). Such components and systems are often perceived as peripheral to the reactor and are left somewhat unattended. That is, even when inspected, if they are not perceived to be causing some immediate problem, they may not be paid due attention. Attention to such systems normally involves long term monitoring and possibly reasoning with multiple features and evidence, requirements that are not best suited for humans.

Loviisa nuclear power plant analyzer

International Nuclear Information System (INIS)

Porkholm, K.; Nurmilaukas, P.; Tiihonen, O.; Haenninen, M.; Puska, E.

1992-12-01

The APROS Simulation Environment has been developed since 1986 by Imatran Voima Oy (IVO) and the Technical Research Centre of Finland (VTT). It provides tools, solution algorithms and process components for use in different simulation systems for design, analysis and training purposes. One of its main nuclear applications is the Loviisa Nuclear Power Plant Analyzer (LPA). The Loviisa Plant Analyzer includes all the important plant components both in the primary and in the secondary circuits. In addition, all the main control systems, the protection system and the high voltage electrical systems are included. (orig.)

Computer-aided stress analysis system for nuclear plant primary components

International Nuclear Information System (INIS)

Murai, Tsutomu; Tokumaru, Yoshio; Yamazaki, Junko.

1980-06-01

Generally it needs a vast quantity of calculation to make the stress analysis reports of nuclear plant primary components. In Japan, especially, stress analysis reports are under obligation to make for each plant. In Mitsubishi Heavy Industries, Ltd., We have been making great efforts to rationalize the process of analysis for about these ten years. As the result of rationalization up to now, a computer-aided stress analysis system using graphic display, graphic tablet, data file, etc. was accomplished and it needs us only the least hand work. In addition we developed a fracture safety analysis system. And we are going to develop the input generator system for 3-dimensional FEM analysis by graphics terminals in the near future. We expect that when the above-mentioned input generator system is accomplished, it will be possible for us to solve instantly any case of problem. (author)

Structural mechanics of nuclear plant components

International Nuclear Information System (INIS)

Roche, R.

1986-10-01

Sound structural analysis are needed for designing safe and reliable components, hence his play is very important in nuclear industry. This report is a provisional writing on the good practice in structural mechanics. Emphasis is put on non elastic analysis, damage appraisal, fatigue, fracture mechanics and also on elevated temperature behaviour [fr

Aging management and PLEX in Swiss nuclear power plants and prioritization of safety class 2 and 3 components

International Nuclear Information System (INIS)

Fuchs, R.; Stejskal, J.

2000-01-01

In this presentation ageing management of systems and components important to safety of the Swiss nuclear power plants are presented. Status of electrical components, status of mechanical components as well as status of civil structures are reviewed. The scheme of the high pressure core spray system is included

Development of in-service inspection plans for nuclear components at the Surry 1 nuclear power station

International Nuclear Information System (INIS)

Vo, T.V.; Simonen, F.A.; Doctor, S.R.; Smith, B.W.; Gore, B.F.

1993-01-01

As part of the nondestructive evaluation reliability program sponsored by the US Nuclear Regulatory Commission at Pacific Northwest Laboratory, a methodology has been developed for establishing in-service inspection priorities of nuclear power plant components. The method uses results of probabilistic risk assessment in conjunction with the techniques of failure modes and effects analysis to identify and prioritize the most risk-important systems and components for inspection at nuclear power plants. Surry nuclear power station unit 1 was selected for demonstrating the methodology. The specific systems selected for analysis were the reactor pressure vessel, the reactor coolant, the low pressure injection including the accumulators, and the auxiliary feedwater. The results provide a risk-based ranking of components that can be used to establish a prioritization of the components and a basis for developing improved in-service inspection plans at nuclear power plants

Seismic proving tests on the reliability for large components and equipment of nuclear power plants

International Nuclear Information System (INIS)

Ohno, Tokue; Tanaka, Nagatoshi

1988-01-01

Since Japan has destructive earthquakes frequently, the structural reliability for large components and equipment of nuclear power plants are rigorously required. They are designed using sophisticated seismic analyses and have not yet encountered a destructive earthquake. When nuclear power plants are planned, it is very important that the general public understand the structural reliability during and after an earthquake. Seismic Proving Tests have been planned by Ministry of International Trade and Industry (Miti) to comply with public requirement in Japan. A large-scale high-performance vibration table was constructed at Tasted Engineering Laboratory of Nuclear Power Engineering Test Center (NU PEC), in order to prove the structural reliability by vibrating the test model (of full scale or close to the actual size) in the condition of a destructive earthquake. As for the test models, the following four items were selected out of large components and equipment important to the safety: Reactor Containment Vessel; Primary Coolant Loop or Primary Loop Recirculation System; Reactor Pressure Vessel; and Reactor Core Internals. Here is described a brief of the vibration table, the test method and the results of the tests on PWR Reactor Containment Vessel and BWR Primary Loop Recirculation System (author)

Seismic fragility of nuclear power plant components. Phase I

International Nuclear Information System (INIS)

Bandyopadhyay, K.K.; Hofmayer, C.H.

1986-06-01

As part of the Component Fragility Research Program, sponsored by the US Nuclear Regulatory Commission, BNL is involved in establishing seismic fragility levels for various nuclear power plant equipment by identifying, collecting and analyzing existing test data from various sources. In Phase I of this program, BNL has reviewed approximately seventy test reports to collect fragility or high level test data for switchgears, motor control centers and similar electrical cabinets, valve actuators and numerous electrical devices of various manufacturers and models. This report provides an assessment and evaluation of the data collected in Phase I. The fragility data for medium voltage and low voltage switchgears and motor control centers are analyzed using the test response spectra (TRS) as a measure of the fragility level. The analysis reveals that fragility levels can best be described by a group of TRS curves corresponding to various failure modes. The lower-bound curve indicates the initiation of malfunctioning or structural damage; whereas, the upper-bound curve corresponds to overall failure of the equipment based on known failure modes. High level test data for some components are included in the report. These data indicate that some components are inherently strong and do not exhibit any failure mode even when tested at the vibration limit of a shake table. The common failure modes are identified in the report. The fragility levels determined in this report have been compared with those used in the PRA and Seismic Margin Studies. It appears that the BNL data better correlate with the HCLPF (High Confidence of a Low Probability of Failure) level used in Seismic Margin Studies and can improve this level as high as 60% for certain applications. Specific recommendations are provided for proper application of BNL fragility data to other studies

Maintenance Management Support Systems for component aging estimation at nuclear power plants

International Nuclear Information System (INIS)

Shimizu, Shunichi; Ando, Yasumasa; Morioka, Toshihiko; Okuzumi, Naoaki

1991-01-01

Maintenance Management Support Systems (MMSSs) for nuclear power plants have been developed using component aging estimation methods and decision tree analysis for maintenance planning. The former evaluates actual component reliability through statistical analysis on field maintenance data. The latter provides preventive maintenance (PM) planning guidance using heuristic expert knowledge and estimated reliability parameters. The following aspects have been investigated: (1) A systematic and effective method of managing components/parts design information and field maintenance data (2) A method for estimating component aging based on a statistical analysis of field maintenance data (3) A method for providing PM planning guidance using estimated component reliability/performance parameters and decision tree analysis. Based on these investigations, two MMSSs were developed. One deals with 'general maintenance data', which are common to all component types and are amenable to common data handling. The other system deals with 'specific maintenance data', which are specific to an individual component type. Both systems provide PM planning guidance for PM cycles propriety and the PM work priority. The function of these systems were verified using simulated maintenance data. (author)

Nuclear heat source component design considerations for HTGR process heat reactor plant concept

International Nuclear Information System (INIS)

McDonald, C.F.; Kapich, D.; King, J.H.; Venkatesh, M.C.

1982-01-01

Using alternate energy sources abundant in the U.S.A. to help curb foreign oil imports is vitally important from both national security and economic standpoints. Perhaps the most forwardlooking opportunity to realize national energy goals involves the integrated use of two energy sources that have an established technology base in the U.S.A., namely nuclear energy and coal. The coupling of a high-temperature gas-cooled reactor (HTGR) and a chemical process facility has the potential for long-term synthetic fuel production (i.e., oil, gasoline, aviation fuel, hydrogen, etc.) using coal as the carbon source. Studies are in progress to exploit the high-temperature capability of an advanced HTGR variant for nuclear process heat. The process heat plant discussed in this paper has a 1170-MW(t) reactor as the heat source and the concept is based on indirect reforming, i.e., the high-temperature nuclear thermal energy is transported (via an intermediate heat exchanger (IHX)) to the externally located process plant by a secondary helium transport loop. Emphasis is placed on design considerations for the major nuclear heat source (NHS) components, and discussions are presented for the reactor core, prestressed concrete reactor vessel (PCRV), rotating machinery, and heat exchangers

Component design considerations for gas turbine HTGR waste-heat power plant

International Nuclear Information System (INIS)

McDonald, C.F.; Vrable, D.L.

1976-01-01

Component design considerations are described for the ammonia waste-heat power conversion system of a large helium gas-turbine nuclear power plant under development by General Atomic Company. Initial component design work was done for a reference plant with a 3000-MW(t) High-Temperature Gas-Cooled Reactor (HTGR), and this is discussed. Advanced designs now being evaluated include higher core outlet temperature, higher peak system pressures, improved loop configurations, and twin 4000-MW(t) reactor units. Presented are the design considerations of the major components (turbine, condenser, heat input exchanger, and pump) for a supercritical ammonia Rankine waste heat power plant. The combined cycle (nuclear gas turbine and waste-heated plant) has a projected net plant efficiency of over 50 percent. While specifically directed towards a nuclear closed-cycle helium gas-turbine power plant (GT-HTGR), it is postulated that the bottoming waste-heat cycle component design considerations presented could apply to other low-grade-temperature power conversion systems such as geothermal plants

Identification of seismically risk-sensitive systems and components in nuclear power plants: feasibility study

International Nuclear Information System (INIS)

Azarm, M.; Boccio, J.; Farahzad, P.

1983-06-01

An approach for the identification of risk-sensitive components in a nuclear power plant during and after a seismic event is described. Application of the methodology to two hypothetical power plants - a Boiling Water Reactor and a Pressurized Water Reactor - are presented and the results are given in tabular and graphical form. Conclusions drawn and lessons learned through the course of this study, based on the relative importance of various accident scenarios and sensitivity analyses, are discussed. In addition, the areas that may need further investigation are identified

Development of a web-based aging monitoring system for an integrity evaluation of the major components in a nuclear power plant

International Nuclear Information System (INIS)

Choi, Jae-Boong; Yeum, Seung-Won; Ko, Han-Ok; Kim, Young-Jin; Kim, Hong-Key; Choi, Young-Hwan; Park, Youn-Won

2010-01-01

Structural and mechanical components in a nuclear power plant are designed to operate for its entire service life. Recently, a number of nuclear power plants are being operated beyond their design life to produce more electricity without shutting down. The critical issue in extending a lifetime is to maintain the level of safety during the extended operation period while satisfying the international regulatory standards. However, only a small portion of these components are of great importance for a significant aging degradation which would deeply affect the long-term safety and reliability of the related facilities. Therefore, it is beneficial to build a monitoring system to measure an aging status. While a number of integrity evaluation systems have been developed for NPPs, a real-time aging monitoring system has not been proposed yet . This paper proposes an expert system for the integrity evaluation of nuclear power plants based on a Web-based Reality Environment (WRE). The proposed system provides the integrity assessment for the major mechanical components of a nuclear power plant under concurrent working environments. In the WRE, it is possible for users to understand a mechanical system such as its size, geometry, coupling condition etc. In conclusion, it is anticipated that the proposed system can be used for a more efficient integrity evaluation of the major components subjected to an aging degradation.

Development of a web-based aging monitoring system for an integrity evaluation of the major components in a nuclear power plant

Energy Technology Data Exchange (ETDEWEB)

Choi, Jae-Boong, E-mail: boong33@skku.ed [SAFE Research Centre, School of Mechanical Engineering, Sungkyunkwan University, 300 Chunchun-dong, Jangan-gu, Suwon, Kyonggi-do 440-746 (Korea, Republic of); Yeum, Seung-Won; Ko, Han-Ok; Kim, Young-Jin [SAFE Research Centre, School of Mechanical Engineering, Sungkyunkwan University, 300 Chunchun-dong, Jangan-gu, Suwon, Kyonggi-do 440-746 (Korea, Republic of); Kim, Hong-Key; Choi, Young-Hwan; Park, Youn-Won [Korea Institute of Nuclear Safety, 34 Gwahak-ro, Yusong-ku, Teajon 305-338 (Korea, Republic of)

2010-01-15

Structural and mechanical components in a nuclear power plant are designed to operate for its entire service life. Recently, a number of nuclear power plants are being operated beyond their design life to produce more electricity without shutting down. The critical issue in extending a lifetime is to maintain the level of safety during the extended operation period while satisfying the international regulatory standards. However, only a small portion of these components are of great importance for a significant aging degradation which would deeply affect the long-term safety and reliability of the related facilities. Therefore, it is beneficial to build a monitoring system to measure an aging status. While a number of integrity evaluation systems have been developed for NPPs, a real-time aging monitoring system has not been proposed yet . This paper proposes an expert system for the integrity evaluation of nuclear power plants based on a Web-based Reality Environment (WRE). The proposed system provides the integrity assessment for the major mechanical components of a nuclear power plant under concurrent working environments. In the WRE, it is possible for users to understand a mechanical system such as its size, geometry, coupling condition etc. In conclusion, it is anticipated that the proposed system can be used for a more efficient integrity evaluation of the major components subjected to an aging degradation.

Safety philosophy and design principles for systems and components of nuclear power plant: external event

International Nuclear Information System (INIS)

Lopes, J.P.G.

1986-01-01

In nuclear power plants, some systems and components are designed to withstand external impacts. Such systems and components are those which have to perform their functions even during and after the occurrences of an earthquake, for example, fulfilling the safety objectives and avoiding the release of radioactive material to the environment. The aim of this report is to introduce the safety philosophy and design principles for systems/components to perform their functions during and after the occurrence of an earthquake, as applied by NUCLEN for Angra 2 and 3. (Author) [pt

Condition Based Prognostics of Passive Components - A New Era for Nuclear Power Plant Life Management

International Nuclear Information System (INIS)

Bakhtiari, S.; Mohanty, S.; Prokofiev, I.; Tregoning, R.

2012-01-01

As part of a research project sponsored by the U.S. NRC, Argonne National Laboratory (ANL) conducted scoping studies to identify viable and promising sensors and techniques for in-situ inspection and real-time monitoring of degradation in nuclear power plant (NPP) systems, structures, and components (SSC). Significant advances have been made over the past two decades toward development of online monitoring (OLM) techniques for detection, diagnostics, and prognostics of degradation in active nuclear power plant (NPP) components (e.g., pumps, valves). However, early detection of damage and degradation in safety-critical passive components, (e.g. piping, tubing pressure vessel), is challenging, and will likely remain so for the foreseeable future. Ensuring the structural integrity of the reactor pressure vessel (RPV) and piping systems in particular is a prerequisite to long term safe operation of NPPs. The current practice is to implement inservice inspection (ISI) and preventive maintenance programs. While these programs have generally been successful, they are limited in that information is only obtained during plant outages. Additionally, these inspections, often the critical path in the outage schedule, are costly, time consuming, and involve potentially high dose to nondestructive examination/evaluation (NDE) personnel. A viable plant-wide on-line structural health monitoring program for continuous and automatic monitoring of critical SSCs could be a more effective approach for guarding against unexpected failures. Specifically, OLM information about the current condition of the SSCs could be input to an online prognostics (OLP) system to forecast their remaining useful life in real time. This paper provides an overview of scoping studies performed at ANL on assessing the viability of OLM and OLP systems for real time and automated monitoring and remaining of condition and the remaining useful life of passive components in NPPs. (author)

Operating experience in cleaning sodium-wetted components at the KNK nuclear power plant

International Nuclear Information System (INIS)

Stade, K.Ch.

1978-01-01

Since 1969, components of the KNK facility, the first sodium cooled nuclear power plant in the Federal Republic of Germany, have been cleaned both by the alcohol and the wet gas techniques. This paper outlines the experience accumulated In the application of these methods, especially in cleaning steam generators and fuel elements. Some preliminary results are indicated of the attempt to clean a cold trap from the primary circuit of the KNK facility. (author)

Comparison between Japan and the United States in the frequency of events in equipment and components at nuclear power plants

International Nuclear Information System (INIS)

Shimada, Yoshio

2007-01-01

The Institute of Nuclear Safety System, Incorporated (INSS) conducted trend analyses until 2005 to compare the frequency of events in certain electrical components and instrumentation components at nuclear power plants between Japan and the United States. The results revealed that events have occurred approximately an order of magnitude less often in Japan than in the United States. This paper compared Japan and the United States in more detail in terms of how often events - events reported under the reporting standards of the Nuclear Information Archive (NUCIA) or the Institute of Nuclear Power Operations (INPO) - occurred in electrical components, instrumentation components and mechanical components at nuclear power plants. The results were as follows: (1) In regard to electrical components and instrumentation components, events have occurred one-eighth less frequently in Japan than in the United States, suggesting that the previous results were correct. (2) Events have occurred more often in mechanical components than electrical components and instrumentation components in both Japan and the United States, and there was a smaller difference in the frequency of events in mechanical components between the two countries. (3) Regarding mechanical components, it was found that events in the pipes for critical systems and equipment, such as reactor coolant systems, emergency core cooling systems, instrument and control systems, ventilating and air-conditioning systems, and turbine equipment, have occurred more often in Japan than in the United States. (4) The above observations suggest that there is little scope for reducing the frequency of events in electrical components and instrumentation components, but that mechanical components such as pipes for main systems like emergency core cooling systems and turbine equipment in the case of PWRs, could be improved by re-examining inspection methods and intervals. (author)

Probabilistic approaches to life prediction of nuclear plant structural components

International Nuclear Information System (INIS)

Villain, B.; Pitner, P.; Procaccia, H.

1996-01-01

In the last decade there has been an increasing interest at EDF in developing and applying probabilistic methods for a variety of purposes. In the field of structural integrity and reliability they are used to evaluate the effect of deterioration due to aging mechanisms, mainly on major passive structural components such as steam generators, pressure vessels and piping in nuclear plants. Because there can be numerous uncertainties involved in a assessment of the performance of these structural components, probabilistic methods. The benefits of a probabilistic approach are the clear treatment of uncertainly and the possibility to perform sensitivity studies from which it is possible to identify and quantify the effect of key factors and mitigative actions. They thus provide information to support effective decisions to optimize In-Service Inspection planning and maintenance strategies and for realistic lifetime prediction or reassessment. The purpose of the paper is to discuss and illustrate the methods available at EDF for probabilistic component life prediction. This includes a presentation of software tools in classical, Bayesian and structural reliability, and an application on two case studies (steam generator tube bundle, reactor pressure vessel). (authors)

Probabilistic approaches to life prediction of nuclear plant structural components

International Nuclear Information System (INIS)

Villain, B.; Pitner, P.; Procaccia, H.

1996-01-01

In the last decade there has been an increasing interest at EDF in developing and applying probabilistic methods for a variety of purposes. In the field of structural integrity and reliability they are used to evaluate the effect of deterioration due to aging mechanisms, mainly on major passive structural components such as steam generators, pressure vessels and piping in nuclear plants. Because there can be numerous uncertainties involved in an assessment of the performance of these structural components, probabilistic methods provide an attractive alternative or supplement to more conventional deterministic methods. The benefits of a probabilistic approach are the clear treatment of uncertainty and the possibility to perform sensitivity studies from which it is possible to identify and quantify the effect of key factors and mitigative actions. They thus provide information to support effective decisions to optimize In-Service Inspection planning and maintenance strategies and for realistic lifetime prediction or reassessment. The purpose of the paper is to discuss and illustrate the methods available at EDF for probabilistic component life prediction. This includes a presentation of software tools in classical, Bayesian and structural reliability, and an application on two case studies (steam generator tube bundle, reactor pressure vessel)

Pilot studies on management of ageing of nuclear power plant components: Results of Phase 1

International Nuclear Information System (INIS)

1992-10-01

To facilitate cooperation between the IAEA Member States and thus to enhance the safety and reliability of operating nuclear plants the IAEA has initiated pilot studies on the management of ageing of four representative plant components: the primary nozzle of the reactor pressure vessel, a motor operated valve, the concrete containment building and instrumentation and control cables. Phase 1 of the studies has been completed and its results are presented in this report. The report documents current understanding of ageing and methods for monitoring and mitigation of this ageing for the above components, identifies existing knowledge and technology gaps and defines follow-up work to deal with these gaps. Refs, figs and tabs

Nuclear plant license renewal

International Nuclear Information System (INIS)

Gazda, P.A.; Bhatt, P.C.

1991-01-01

During the next 10 years, nuclear plant license renewal is expected to become a significant issue. Recent Electric Power Research Institute (EPRI) studies have shown license renewal to be technically and economically feasible. Filing an application for license renewal with the Nuclear Regulatory Commission (NRC) entails verifying that the systems, structures, and components essential for safety will continue to perform their safety functions throughout the license renewal period. This paper discusses the current proposed requirements for this verification and the current industry knowledge regarding age-related degradation of structures. Elements of a license renewal program incorporating NRC requirements and industry knowledge including a schedule are presented. Degradation mechanisms for structural components, their significance to nuclear plant structures, and industry-suggested age-related degradation management options are also reviewed

Concrete component aging and its significance relative to life extension of nuclear power plants

International Nuclear Information System (INIS)

Naus, D.J.

1986-09-01

The objectives of this study are to (1) expand upon the work that was initiated in the first two Electric Power Research Institute studies relative to longevity and life extension considerations of safety-related concrete components in light-water reactor (LWR) facilities and (2) provide background that will logically lead to subsequent development of a methodology for assessing and predicting the effects of aging on the performance of concrete-based materials and components. These objectives are consistent with Nuclear Plant Aging Research (NPAR) Program goals: (1) to identify and characterize aging and service wear effects that, if unchecked, could cause degradation of structures, components, and systems and, thereby, impair plant safety; (2) to identify methods of inspection, surveillance, and monitoring or of evaluating residual life of structures, components, and systems that will ensure timely detection of significant aging effects before loss of safety function; and (3) to evaluate the effectiveness of storage, maintenance, repair, and replacement practices in mitigating the rate and extent of degradation caused by aging and service wear

Age-dependent risk-based methodology and its application to prioritization of nuclear power plant components and to maintenance for managing aging using PRAs

International Nuclear Information System (INIS)

Levy, I.S.; Vesely, W.E.

1990-01-01

This paper is based on a study to demonstrate several important ways that the age-dependent risk-based methodology developed by the Nuclear Plant Aging Research (NPAR) Program may be applied to resolving important issues related to the aging of nuclear power plant systems, structures, and components (SSCs). The study was sponsored by the NPAR Program of the Division of Engineering, Office of Nuclear Regulatory Research of the U.S. Nuclear Regulatory Commission (NRC). Initiated on the basis of a Users Need Request, the age-dependent risk-based methodology has been under development by the NPAR Program for several years. In this methodology, the time-dependent change in a component's risk contribution is the product of two factors: (1) the risk importance of the component (e.g., the change in its risk contribution when it is assumed to be totally unavailable to perform its intended safety function) and (2) the change in its unavailability with time. This change in the component's unavailability with time is a function of the component's aging rate and plant inspection and maintenance practices. The methodology permits evaluations of the age-dependent risk contributions from both single- and multiple-components. Principal results and conclusions generated by the methodology demonstrations are discussed

Assessment and management of ageing of major nuclear power plant components important to safety: Metal components of BWR containment systems

International Nuclear Information System (INIS)

2000-10-01

At present, there are over four hundred operational nuclear power plants (NPPs) in IAEA Member States. Operating experience has shown that ineffective control of the ageing degradation of the major NPP components (e.g. caused by unanticipated phenomena and by operating, maintenance or manufacturing errors) can jeopardize plant safety and also plant life. Ageing in these NPPs must therefore be effectively managed to ensure the availability of design functions throughout the plant service life. From the safety perspective, this means controlling within acceptable limits the ageing degradation and wear-out of plant components important to safety so that adequate safety margins remain, i.e. integrity and functional capability in excess of normal operating requirements. This TECDOC is one in a series of reports on the assessment and management of ageing of the major NPP components important to safety. The reports are based on experience and practices of NPP operators, regulators, designers, manufacturers, and technical support organizations and a widely accepted Methodology for the Management of Ageing of NPP Components Important to Safety, which was issued by the IAEA in 1992. The current practices for the assessment of safety margins (fitness for service) and the inspection, monitoring and mitigation of ageing degradation of selected components of Canada deuterium-uranium (CANDU) reactors, boiling water reactors (BWRs), pressurized water reactors (PWRs), and water moderated, water cooled energy reactors (WWERs) are documented in the reports. These practices are intended to help all involved directly and indirectly in ensuring the safe operation of NPPs, and to provide a common technical basis for dialogue between plant operators and regulators when dealing with age related licensing issues. The guidance reports are directed toward technical experts from NPPs and from regulatory, plant design, manufacturing and technical support organizations dealing with specific

GERB viscous dampers in application for pipelines and other components in nuclear power plants

International Nuclear Information System (INIS)

Masopust, R.; Podrouzek, J.; Zach, J.

1993-01-01

VISCODAMPERS from GERB, Germany, are now widely used as reliable shock restraints against earthquake and other shock effects for the most important safety-related pipelines and components in several Czech and Slovak nuclear power plants. Having many technical advantages they are, at the same time, relatively inexpensive in comparison to conventionally used snubbers. Their properties are briefly described and several practical applications are explained in this paper. (author)

Seismic instrumentation for nuclear power plants

International Nuclear Information System (INIS)

Senne Junior, M.

1983-01-01

A seismic instrumentation system used in Nuclear Power Plants to monitor the design parameters of systems, structures and components, needed to provide safety to those Plants, against the action of earthquakes is described. The instrumentation described is based on the nuclear standards in force. The minimum amount of sensors and other components used, as well as their general localization, is indicated. The operation of the instrumentation system as a whole and the handling of the recovered data are dealt with accordingly. The various devices used are not covered in detail, except for the accelerometer, which is the seismic instrumentation basic component. (Author) [pt

Ageing studies on materials, components and process instruments used in nuclear power plants

International Nuclear Information System (INIS)

Bora, J.S.

1997-04-01

This report is a compilation of test results of thermal and radiation ageing tests carried out in the laboratory over a period of 25 years on diverse engineering materials, components and instruments used in nuclear power plants. Test items covered are different types of electrical cables, elastomers, surface coatings, electrical and electronics components and process instruments. Effects of thermal and radiation ageing on performance parameters are shown in tabular forms. Apart from finding the characteristics, capabilities and limitations of test items, ageing research has helped in pin-pointing sub-standard and critical parts and necessary corrective action has been taken. This report is expected to be quite useful to the manufacturers users and researchers for reference and guidance. (author)

In-service materials testing of selected components of unit 1 and 2 of V-1 nuclear power plant

International Nuclear Information System (INIS)

Cintula, J.

1982-01-01

The task of in-service nondestructive testing of nuclear installations is to confirm that the state of base material and welded joints has not changed owing to mechanical, thermal or radiation stress. Under the regulations of safe operation the first in-service inspection of all components of a WWER 440 reactor must be carried out after 15,000 to 2O,00O operating hours at the latest. Further in-service inspections are repeated after 30,000 hours (pressure vessels) and 40,000 hours (the main steam piping and the feedwater piping). Proceeding from experience gained so far, intervals are suggested for in-service checks of the other components of the V-1 nuclear power plant. Also briefly described are the main nondestructive methods used for such checks at this power plant. (Z.M.)

Seismic instrumentation for nuclear power plants

International Nuclear Information System (INIS)

Senne Junior, M.

1983-07-01

A seismic instrumentation system used in Nuclear Power Plants to monitor the design parameters of systems, structures and components, needed to provide safety to those plants, against the action of earth quarks is described. The instrumentation is based on the nuclear standards and other components used, as well as their general localization is indicated. The operation of the instrumentation system as a whole and the handling of the recovered data are dealt with accordingly. The accelerometer is described in detail. (Author) [pt

The maintenance optimization of structural components in nuclear power plants

International Nuclear Information System (INIS)

Bryla, P.; Ardorino, F.; Aufort, P.; Jacquot, J.P.; Magne, L.; Pitner, P.; Verite, B.; Villain, B.; Monnier, B.

1997-10-01

An optimization process, called 'OMF-Structures', is developed by Electricite de France (EDF) in order to extend the current 'OMF' Reliability Centered Maintenance to piping structural components. The Auxiliary Feedwater System of a 900 MW French nuclear plant has been studied in order to lay the foundations of the method. This paper presents the currently proposed principles of the process. The principles of the OMF-Structures process include 'Risk-Based Inspection' concepts within an RCM process. Two main phases are identified: The purpose of the first phase is to select the risk-significant failure modes and associated elements. This phase consists of two major steps: potential consequences evaluation and reliability performance evaluation. The second phase consists of the definition of preventive maintenance programs for piping elements that are associated with risk-significant failure modes. (author)

Dynamic Simulator for Nuclear Power Plants (DSNP)

International Nuclear Information System (INIS)

Saphier, D.

1976-01-01

A new simulation language DSNP (Dynamic Simulator for Nuclear Power Plants) is being developed. It is a simple block oriented simulation language with an extensive library of component and auxiliary modules. Each module is a self-contained unit of a part of a physical component to be found in nuclear power plants. Each module will be available in four levels of sophistication, the fourth being a user supplied model. A module can be included in the simulation by a single statement. The precompiler translates DSNP statements into FORTRAN statements, takes care of the module parameters and the intermodular communication blocks, prepares proper data files and I/0 statements and searches the various libraries for the appropriate component modules. The documentation is computerized and all the necessary information for a particular module can be retrieved by a special document generator. The DSNP will be a flexible tool which will allow dynamic simulations to be performed on a large variety of nuclear power plants or specific components of these plants

Preinspection of nuclear power plant systems

International Nuclear Information System (INIS)

1975-01-01

The general plans of the systems affecting the safety of the nuclear power plants are accepted by the Institute of Radiation Protection (IRP) on the basis of the preinspection of the systems. This is the prerequisite of the preinspection of the structures and components belonging to these systems. Exceptionally, when separately agreed, the IRP may perform the preinspection of a separate structure or component, although the preinspection documentation of the whole system, e.g. the nuclear heat generating system, has not been accepted. This guide applies to the nuclear power plant systems that have been defined to be preinspected in the classification document accepted by the IRP

Future needs for inelastic analysis in design of high-temperature nuclear plant components

International Nuclear Information System (INIS)

Corum, J.M.

1980-01-01

The role that inelastic analyses play in the design of high-temperature nuclear plant components is described. The design methodology, which explicitly accounts for nonlinear material deformation and time-dependent failure modes, requires a significant level of realism in the prediction of structural response. Thus, material deformation and failure modeling are, along with computational procedures, key parts of the methodology. Each of these is briefly discussed along with validation by comparisons with benchmark structural tests, and problem areas and needs are discussed for each

Requirements for class 1, 2, and 3 pressure-retaining systems and components in CANDU nuclear power plants

International Nuclear Information System (INIS)

1991-09-01

This third edition of CAN/CSA-N285.1 supersedes the 1981 and 1975 editions. It provides the specific requirements for design, fabrication, and installation of Class 1, 2 and 3 pressure-retaining systems and components in CANDU nuclear power plants, and over pressure protection of the heat transport system. The general requirements for pressure-retaining systems and components are given in CSA Standard CAN/CSA-N285.0, with which Class 1, 2 and 3 systems and components must also comply

Components production and assemble of the irradiation capsule of the Surveillance Program of Materials of the nuclear power plant of Laguna Verde

International Nuclear Information System (INIS)

Medrano, A.

2009-01-01

To predict the effects of the neutrons radiation and the thermal environment about the mechanical properties of the reactor vessel materials of the nuclear power plant of Laguna Verde, a surveillance program is implemented according to the outlines settled by Astm E185-02 -Standard practice for design of surveillance programs for light-water moderated nuclear power reactor vessels-. This program includes the installation of three irradiation capsules of similar materials to those of the reactor vessels, these samples are test tubes for mechanical practices of impact and tension. In the National Institute of Nuclear Research and due to the infrastructure as well as of the actual human resources of the Pilot Plant of Nuclear Fuel Assembles Production it was possible to realize the materials rebuilding extracted in 2005 of Unit 2 of nuclear power plant of Laguna Verde as well as the production, assemble and reassignment of the irradiation capsule made in 2006. At the present time the surveillance materials extracted in 2008 of Unit 1 of the nuclear power plant of Laguna Verde are reconstituting and the components are manufactured for the assembles of the irradiation capsule that will be reinstalled in the reactor vessel in 2010. The purpose of the present work is to describe the necessary components as well as its disposition during the assembles of the irradiation capsule for the surveillance program of the reactors vessel of the nuclear power plant of Laguna Verde. (Author)

Partner of nuclear power plants

International Nuclear Information System (INIS)

Gribi, M.; Lauer, F.; Pauli, W.; Ruzek, W.

1992-01-01

Sulzer, the Swiss technology group, is a supplier of components and systems for nuclear power plants. Important parts of Swiss nuclear power stations, such as containments, reactor pressure vessels, primary pipings, are made in Winterthur. Sulzer Thermtec AG and some divisions of Sulzer Innotec focus their activities on servicing and backfitting nuclear power plants. The European market enjoys priority. New types of valves or systems are developed as economic solutions meeting more stringent criteria imposed by public authorities or arising from operating conditions. (orig.) [de

Case study on the use of PSA methods: Determining safety importance of systems and components at nuclear power plants

International Nuclear Information System (INIS)

1991-04-01

This case study emphasizes the step of probabilistic safety assessment (PSA) regarding identification of systems and components important to nuclear plant safety. An importance analysis involves combining information that is both qualitative and probabilistic in nature to generate a numerical ranking to determine the system and/or component failures that dominate the risk. Such a ranking can suggest where hardware, software, human factors and component design changes can be implemented to improve plant safety. Examples of using ranking methodology are described. A qualitative ranking criteria is discussed for components and systems that are not included in a PSA. 18 refs, 7 figs, 18 tabs

Ecological impacts and damage - comparison of selected components for nuclear and conventional power plants (example of Mochovce nuclear power plant)

International Nuclear Information System (INIS)

Bucek, M.

1984-01-01

A comparison is given of ecological damage for the nuclear power plant in Mochovce and a conventional power plant with the same power. Ecological effects and damage are divided into three groups: comparable damage, ecological damage caused only by conventional power plants and ecological damage caused only by nuclear power plants. In the first group the factors compared are land requisition, consumption of utility water and air consumption. In the second group are enumerated losses of crops (cereals, sugar beet, potatoes, oleaginous plants) and losses caused by increased disease rate owing to polluted environment by conventional power plants. In the third group health hazards are assessed linked with ionizing radiation. Also considered are vent stack escapes. (E.S.)

Maintenance of nuclear power plants

International Nuclear Information System (INIS)

Lashgari, Farbod.

1995-01-01

This paper is about maintenance of nuclear power plants. In part one, the outage management of nuclear power plants has described. Meaning of the outage and objectives of outage management is given in introduction. The necessity of a long-term outage strategy is shown in chapter one. The main parts of an outage are as follows: Planning; Preparation; Execution, Each of them and also post-outage review have been explained in the followed chapters. Part two deals with technical details of main primary components of nuclear power plant type WWER. After an introduction about WWER reactors, in each chapter first the general and detailed description of main primary components has given and then their maintenance schedules and procedures. Chapter about reactor and steam generator is related to both types of WWER-440 and WWER-1000, but chapter about reactor coolant pump has specified to WWER-1000 to be more in details.(author)

Development of a simple method for classifying the degree of importance of components in nuclear power plants using probabilistic analysis technique

International Nuclear Information System (INIS)

Shimada, Yoshio; Miyazaki, Takamasa

2006-01-01

In order to analyze large amounts of trouble information of overseas nuclear power plants, it is necessary to select information that is significant in terms of both safety and reliability. In this research, a method of efficiently and simply classifying degrees of importance of components in terms of safety and reliability while paying attention to root-cause components appearing in the information was developed. Regarding safety, the reactor core damage frequency (CDF), which is used in the probabilistic analysis of a reactor, was used. Regarding reliability, the automatic plant trip probability (APTP), which is used in the probabilistic analysis of automatic reactor trips, was used. These two aspects were reflected in the development of criteria for classifying degrees of importance of components. By applying these criteria, a method of quantitatively and simply judging the significance of trouble information of overseas nuclear power plants was developed. (author)

Pilot studies of management of ageing of nuclear power plant instrumentation and control components

International Nuclear Information System (INIS)

Burnay, S.G.; Simola, K.; Kossilov, A.; Pachner, J.

1993-01-01

This paper describes pilot studies which have been implemented to study the aging behavior of safety related component parts of nuclear power plants. In 1989 the IAEA initiated work on pilot studies related to the aging of such components. Four components were identified for study. They are the primary nozzle of a reactor vessel; a motor operated isolating valve; the concrete containment building; and instrumentation and control cables within the containment facility. The study was begun with phase 1 efforts directed toward understanding the aging process, and methods for monitoring and minimizing the effects of aging. Phase 2 efforts are directed toward aging studies, documentation of the ideas put forward, and research to answer questions identified in phase 1. This paper describes progress made on two of these components, namely the motor operated isolation valves, and in-containment I ampersand C cables

Methodology of aging management in structures, systems and components of a nuclear power plant and its application to a pilot program in Laguna Verde

International Nuclear Information System (INIS)

Jarvio C, G.; Fernandez S, G.

2009-10-01

From its origin the nuclear power plants confront the effects of time and of environment, giving as result the aging of its structures, systems and components. In this document the general process is described for the establishment of Aging Management Program developed by IAEA. Following the program methodology is guaranteed that a nuclear power plant manages the aging effects appropriately and to make decisions for its solution, assuring the characteristic functions of structures, systems and components of same nuclear power plant. On the other hand, the implantation of an aging management program constitutes the base for development of a licence renovation program, like it can be the specific case of the Central Laguna Verde Units 1 and 2. (Author)

Commissioning of the nuclear power plant

International Nuclear Information System (INIS)

Furtado, P.M.; Rolf, F.

1984-01-01

Nuclear Power Plant Angra 2, located at Itaorna Beach-Angra dos Reis is the first plant of the Brazilian-German Agreement to be commissioned. The Nuclear Power Plant is a pressurized water reactor rated at 3765 Mw thermal/1325 Mw electrical. For commissioning purpose the plant is divided into 110 systems. Plant commissioning objective is to demonstrate the safe and correct operation of each plan component, system and of the whole plant in agreement with design conditions, licensing requirements and contractual obligations. This work gives a description of plant commissioning objectives, activities their time sequence, and documentation. (Author) [pt

Nuclear Power Plant Module, NPP-1: Nuclear Power Cost Analysis.

Science.gov (United States)

Whitelaw, Robert L.

The purpose of the Nuclear Power Plant Modules, NPP-1, is to determine the total cost of electricity from a nuclear power plant in terms of all the components contributing to cost. The plan of analysis is in five parts: (1) general formulation of the cost equation; (2) capital cost and fixed charges thereon; (3) operational cost for labor,…

A Procedure for Determination of Degradation Acceptance Criteria for Structures and Passive Components in Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Nie, J.; Braverman, J.; Hofmayer, C.; Choun, Y-S.; Hahm, D.; Choi, I-K.

2012-01-30

The Korea Atomic Energy Research Institute (KAERI) has been collaborating with Brookhaven National Laboratory since 2007 to develop a realistic seismic risk evaluation system which includes the consideration of aging of structures and components in nuclear power plants (NPPs). This collaboration program aims at providing technical support to a five-year KAERI research project, which includes three specific areas that are essential to seismic probabilistic risk assessment: (1) probabilistic seismic hazard analysis, (2) seismic fragility analysis including the effects of aging, and (3) a plant seismic risk analysis. The understanding and assessment of age-related degradations of structures, systems, and components and their impact on plant safety is the major goal of this KAERI-BNL collaboration. Four annual reports have been published before this report as a result of the collaboration research.

Final environmental impact statement for the continued operation of the Pantex Plant and associated storage of nuclear weapon components. Volume 1 -- Main report

International Nuclear Information System (INIS)

1996-11-01

This document assesses the potential environmental impacts over approximately 10 years of continued operation of Pantex Plant, including foreseeable projects and activities. For Pantex Plant, this document assesses the alternatives of No Action, Relocation of the storage of plutonium components (pits) resulting from nuclear weapon disassembly activities at Pantex Plant to another site, and the Proposed Action (Preferred Alternative) of continuing operations and increasing the quantity of pits in interim storage at Pantex Plant. For the Pit Storage Relocation Alternative, this document also assesses the potential environmental impacts to three DOE candidate sites and one Department of Defense candidate site that could be selected for the relocation of the nuclear component storage activities from Pantex Plant. Evaluations of site infrastructure, land resources, geology and soils, water resources, air quality, acoustics, biotic resources, cultural resources, socio-economic resources, intrasite transportation, waste management, human health, aircraft accidents, and environmental justice for Pantex Plant and the candidate sites are included in the assessment. The intersite transportation of nuclear and hazardous materials is also assessed

GERB viscous dampers in applications for pipelines and other components in Czechoslovak nuclear power plants

International Nuclear Information System (INIS)

Masopust, R.; Podrouzek, J.

1992-01-01

VISCODAMPERS from GERB, Germany, are now widely used as reliable shock restraints against earthquake and other shock effects for the most important safety-related pipelines and components in several Czechoslovak nuclear power plants. Having many technical advantages they are, at the same time, relatively inexpensive in comparison with conventional snubbers. Their properties are briefly described and several practical applications are explained. (author) 3 tabs., 9 figs., 8 refs

Feasibility study of component risk ranking for plant maintenance

International Nuclear Information System (INIS)

Ushijima, Koji; Yonebayashi, Kenji; Narumiya, Yoshiyuki; Sakata, Kaoru; Kumano, Tetsuji

1999-01-01

Nuclear power is the base load electricity source in Japan, and reduction of operation and maintenance cost maintaining or improving plant safety is one of the major issues. Recently, Risk Informed Management (RIM) is focused as a solution. In this paper, the outline regarding feasibility study of component risk ranking for plant maintenance for a typical Japanese PWR plant is described. A feasibility study of component risk raking for plant maintenance optimization is performed on check valves and motor-operated valves. Risk ranking is performed in two steps using probabilistic analysis (quantitative method) for risk ranking of components, and deterministic examination (qualitative method) for component review. In this study, plant components are ranked from the viewpoint of plant safety / reliability, and the applicability for maintenance is assessed. As a result, distribution of maintenance resources using risk ranking is considered effective. (author)

Three technical issues in fatigue damage assessment of nuclear power plant components

International Nuclear Information System (INIS)

Ware, A.G.; Shah, V.N.

1991-01-01

This paper addresses three technical issues that affect the fatigue damage assessment of nuclear power plant components: the effect of the environment on the fatigue life, the importance of the loading sequence in calculating the fatigue crack-initiation damage, and the adequacy of current inservice inspection requirements and methods to characterize fatigue cracks. The environmental parameters that affect the fatigue life of carbon and low alloy steel components are the sulphur content in the steel, the temperature, the amount of dissolved oxygen in the coolant, and the presence of oxidizing agents such as copper oxide. The occurrence of large-amplitude stress cycles early in a component's life followed by low-amplitude stress cycles may cause crack initiation at a cumulative usage factor less than 1.0. The current inservice inspection requirements include volumetric inspections of welds but not of some susceptible sites in the base metal. In addition, the conventional ultrasonic testing techniques need to be improved for reliable detection and accurate sizing of fatigue cracks. 28 refs., 4 figs., 1 tab

Lifetime management for mechanical systems, structures and components in nuclear power plants

International Nuclear Information System (INIS)

Roos, E.; Herter, K.-H.; Schuler, X.

2006-01-01

Guidelines, codes and standards contain regulations and requirements with respect to the quality of mechanical systems, structures and components (SSC) of nuclear power plants. These concern safe operation during the total lifetime (lifetime management), safety against ageing phenomena (ageing management) as well as proof of integrity (e.g. break exclusion or avoidance of fracture). Within this field the ageing management is a key element. Depending on the safety-relevance of the SSC under observation including preventive maintenance various tasks are required in particular to clarify the mechanisms which contribute system-specifically to the damage of the components and systems and to define their controlling parameters which have to be monitored and checked. Appropriate continuous or discontinuous measures are to be considered in this connection. The approach to ensure a high standard of quality in operation and the management of the technical and organisational aspects are demonstrated and explained

Quality assurance during the manufacture of nuclear power plant components

International Nuclear Information System (INIS)

Mueller, J.

1976-01-01

Apart from the special requirements of quality assurance in the production of components for the nuclear industry, in particular nuclear power stations, the author discusses special methods of quality control in the testing of welded joints. (TK) [de

In-service inspection of electronics components, circuits and nuclear radiation detectors

International Nuclear Information System (INIS)

Darbhe, M.D.

2002-01-01

A nuclear reactor is a complex process plant. Like a nuclear power plant, the research reactors also employ various nuclear and process systems, the scope and number of such systems being plant-specific. In-service inspection of these systems is an important requirement and is applied at various levels of their constituent units such as detectors, electronics components, circuits and integrated systems. The sensors used cover a wide range such as neutronic, radiation, process (pressure, temperature, flow, level) and many others. The present discussion is limited to neutronic and radiation detectors. The electronic components used normally consist of passive components like resistors, capacitors, semiconductor components like diodes, transistors, analog integrated circuits and digital integrated circuits and electromagnetic relays, to name a few. In order to have a comprehensive surveillance and ISI plan, over the entire plant life, it is necessary to understand various mechanisms, which degrade the performance of these systems. These are discussed initially and later various ISI methods that are used on component-circuit or system level, to ensure optimum system performance, are discussed. The computerised systems, because of hardware and software considerations, have to be given special attention, and the same are discussed briefly

Increasing reliability of nuclear energy equipment and at nuclear power plants

International Nuclear Information System (INIS)

Ochrana, L.

1997-01-01

The Institute of Nuclear Energy at the Technical University in Brno cooperates with nuclear power plants in increasing their reliability. The teaching programme is briefly described. The scientific research programme of the Department of Heat and Nuclear Power Energy Equipment in the field of reliability is based on a complex systematic concept securing a high level of reliability. In 1996 the Department prepared a study dealing with the evaluation of the maintenance system in a nuclear power plant. The proposed techniques make it possible to evaluate the reliability and maintenance characteristics of any individual component in a nuclear power plant, and to monitor, record and evaluate data at any given time intervals. (M.D.)

Application of large-scaled pre-cast components for the construction of water intake for a nuclear power plant

International Nuclear Information System (INIS)

Topolnicki, M.

1976-01-01

Problem of the construction of water intake for a 4000 MW nuclear power plant located at the seashore is solved. The advantages of application of large-size pre-cast components are presented,. The constructional solutions and proposed technologies are described in detail. (A.S.)

Reliability methods in nuclear power plant ageing management

International Nuclear Information System (INIS)

Simola, K.

1999-01-01

The aim of nuclear power plant ageing management is to maintain an adequate safety level throughout the lifetime of the plant. In ageing studies, the reliability of components, systems and structures is evaluated taking into account the possible time-dependent degradation. The phases of ageing analyses are generally the identification of critical components, identification and evaluation of ageing effects, and development of mitigation methods. This thesis focuses on the use of reliability methods and analyses of plant- specific operating experience in nuclear power plant ageing studies. The presented applications and method development have been related to nuclear power plants, but many of the approaches can also be applied outside the nuclear industry. The thesis consists of a summary and seven publications. The summary provides an overview of ageing management and discusses the role of reliability methods in ageing analyses. In the publications, practical applications and method development are described in more detail. The application areas at component and system level are motor-operated valves and protection automation systems, for which experience-based ageing analyses have been demonstrated. Furthermore, Bayesian ageing models for repairable components have been developed, and the management of ageing by improving maintenance practices is discussed. Recommendations for improvement of plant information management in order to facilitate ageing analyses are also given. The evaluation and mitigation of ageing effects on structural components is addressed by promoting the use of probabilistic modelling of crack growth, and developing models for evaluation of the reliability of inspection results. (orig.)

Reliability methods in nuclear power plant ageing management

Energy Technology Data Exchange (ETDEWEB)

Simola, K. [VTT Automation, Espoo (Finland). Industrial Automation

1999-07-01

The aim of nuclear power plant ageing management is to maintain an adequate safety level throughout the lifetime of the plant. In ageing studies, the reliability of components, systems and structures is evaluated taking into account the possible time-dependent degradation. The phases of ageing analyses are generally the identification of critical components, identification and evaluation of ageing effects, and development of mitigation methods. This thesis focuses on the use of reliability methods and analyses of plant- specific operating experience in nuclear power plant ageing studies. The presented applications and method development have been related to nuclear power plants, but many of the approaches can also be applied outside the nuclear industry. The thesis consists of a summary and seven publications. The summary provides an overview of ageing management and discusses the role of reliability methods in ageing analyses. In the publications, practical applications and method development are described in more detail. The application areas at component and system level are motor-operated valves and protection automation systems, for which experience-based ageing analyses have been demonstrated. Furthermore, Bayesian ageing models for repairable components have been developed, and the management of ageing by improving maintenance practices is discussed. Recommendations for improvement of plant information management in order to facilitate ageing analyses are also given. The evaluation and mitigation of ageing effects on structural components is addressed by promoting the use of probabilistic modelling of crack growth, and developing models for evaluation of the reliability of inspection results. (orig.)

Advanced Surveillance, Diagnostic and Prognostic Techniques in Monitoring Structures, Systems and Components in Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-09-15

direction of research, development and demonstration in this area. The technologies discussed in this project are intended to establish the state of the art in surveillance, diagnostics and prognostics (SDP) technologies for equipment and process health monitoring in nuclear facilities. It is also intended to identify technology gaps and research needs of the nuclear industry in the area of SDP. The report draws on the conventional SDP technologies, as well as the latest tools, algorithms and techniques that have emerged over the last few years, especially in enabling technologies including fast data acquisition, data storage, data qualification and data analysis algorithms, such as empirical and physical modelling techniques. These new tools have made it possible to identify problems earlier and with better resolution. The significance of the material presented in this report is that it contributes not only to the current needs of the nuclear industry but also to the design improvements of the next generation of reactors. For example, the nuclear industry is currently striving to operate the plants for up to 80 years or more, as the value of nuclear assets has risen in recent years, resulting partly from environmental concerns with fossil energy production, as well as increased future demand for base load electricity. This long term operation (LTO) or life extension goal of the nuclear industry has stimulated renewed interest in more frequent monitoring of equipment to guard against ageing effects, not to mention the economic benefits that SDP implementation can produce, and contributions to radiation exposure that is as low as reasonably achievable, reduction of human errors, and optimized maintenance. Together with capabilities that enhance situational awareness, the technologies described in this report will enable more holistic management of plant structures, systems and components (SSCs), maintain high capacity factor in LTO and enable higher levels of safe operation

Advanced Surveillance, Diagnostic and Prognostic Techniques in Monitoring Structures, Systems and Components in Nuclear Power Plants

International Nuclear Information System (INIS)

2013-01-01

direction of research, development and demonstration in this area. The technologies discussed in this project are intended to establish the state of the art in surveillance, diagnostics and prognostics (SDP) technologies for equipment and process health monitoring in nuclear facilities. It is also intended to identify technology gaps and research needs of the nuclear industry in the area of SDP. The report draws on the conventional SDP technologies, as well as the latest tools, algorithms and techniques that have emerged over the last few years, especially in enabling technologies including fast data acquisition, data storage, data qualification and data analysis algorithms, such as empirical and physical modelling techniques. These new tools have made it possible to identify problems earlier and with better resolution. The significance of the material presented in this report is that it contributes not only to the current needs of the nuclear industry but also to the design improvements of the next generation of reactors. For example, the nuclear industry is currently striving to operate the plants for up to 80 years or more, as the value of nuclear assets has risen in recent years, resulting partly from environmental concerns with fossil energy production, as well as increased future demand for base load electricity. This long term operation (LTO) or life extension goal of the nuclear industry has stimulated renewed interest in more frequent monitoring of equipment to guard against ageing effects, not to mention the economic benefits that SDP implementation can produce, and contributions to radiation exposure that is as low as reasonably achievable, reduction of human errors, and optimized maintenance. Together with capabilities that enhance situational awareness, the technologies described in this report will enable more holistic management of plant structures, systems and components (SSCs), maintain high capacity factor in LTO and enable higher levels of safe operation

Quality assurance for pipeline installations in nuclear power plants

International Nuclear Information System (INIS)

Anon.

1983-01-01

Approximately 25% of the cost of a nuclear power plant are caused by the pipeline system, i.e. pipes and fixtures. This is an enourmous portion, demanding of the supplier and fitter of these components a very high safety standard. Against the background of the sociopolitical discussion on the safety of nuclear power plants it was a very useful idea of Mannesmann AG, one of the most important manufacturers in this sector, to lay open its quality assurance concept. On the occasion of the symposium ''Safe components for nuclear energy'' held for the expert press it was pointed out that the share of 17% electric energy coming at present from 15 nuclear power plants will increase in future for economic and ecologic reasons. So, it was maintained, the question is not about the ''pro and the con'', but exclusively about the safety standard for nuclear power plants. Specialists from the various branches of the undertaking informed on how this safety concept for the components pipelines and control equipment is realized. (orig./RW) [de

Assessment and management of ageing of major nuclear power plant components important to safety: PWR vessel internals

International Nuclear Information System (INIS)

1999-10-01

At present, there are over four hundred operational nuclear power plants (NPPs) in IAEA Member States. Operating experience has shown that ineffective control of the ageing degradation of the major NPP components (e.g. caused by unanticipated phenomena and by operating, maintenance or manufacturing errors) can jeopardize plant safety and also plant life. Ageing in these NPPs must be therefore effectively managed to ensure the availability of design functions throughout the plant service life. From the safety perspective, this means controlling within acceptable limits the ageing degradation and wear-out of plant components important to safety so that adequate safety margins remain, i.e. integrity and functional capability in excess of normal operating requirements. This TECDOC is one in a series of reports on the assessment and management of ageing of the major NPP components important to safety. The reports are based on experience and practices of NPP operators, regulators, designers, manufacturers, and technical support organizations and a widely accepted Methodology for the Management of Ageing of NPP Components Important to Safety, which was issued by the IAEA in 1992. The current practices for the assessment of safety margins (fitness-for-service) and the inspection, monitoring and mitigation of ageing degradation of selected components of Canada deuterium-uranium (CANDU) reactors, boiling water reactors (BWRs), pressurized water reactors (PWRs), and water moderated, water cooled energy reactors (WWERs) are documented in the reports. These practices are intended to help all involved directly and indirectly in ensuring the safe operation of NPPs, and to provide a common technical basis for dialogue between plant operators and regulators when dealing with age related licensing issues. The guidance reports are directed at technical experts from NPPs and from regulatory, plant design, manufacturing and technical support organizations dealing with specific plant

Failure modes of safety-related components at fires on nuclear power plants

International Nuclear Information System (INIS)

Aaslund, A.

2000-03-01

Probabilistic assessment methods can be used to identify specific plant vulnerabilities. Application of such methods can also facilitate selection among system design alternatives available for safety enhancements. The quality of assessment results is however strongly dependent on realistic and accurate input data for modelling of system component behaviour and failure modes during conditions to be assessed. Use of conservative input data may not lead to results providing guidance on safety upgrades. Adequate input data for probabilistic assessments seems to be lacking for at least failure modes of some electrical components when exposed to a fire. This report presents an attempt to improve the situation with respect to such input data. In order to take advantage of information in existing documentation of fire incident occurrences some of the lessons learned from the fire at Browns Ferry Nuclear Power Plant on March 22, 1975 are discussed in this report. Also a summary of results from different fire tests of electrical cables presented in a fire risk analysis report is a part of the references. The failure modes used to describe fire-induced damage are 'open circuit' and 'hot short' which seems to be commonly accepted terms within the branch. Definitions of the terms are included in the report. Effects of the failure modes when occurring in some of the channels of the reactor protection system are discussed with respect to the existing design of the reactor protection system at Ringhals 2 nuclear power unit. Experiences from the Browns Ferry fire and results from fire tests of electrical cables indicate that the dominating failure mode for electrical cables is 'open circuit'. An 'open circuit' failure leads to circuit disjunction and loss of continuity. The circuit can no longer transmit its signal or power. When affecting channels of the reactor protection system an 'open circuit' failure can cause extensive inadvertent actions of safety related equipment

Assessment and Management of ageing of major nuclear power plant components important to safety: PWR pressure vessels

International Nuclear Information System (INIS)

1999-10-01

At present, there are over four hundred operational nuclear power plants (NPPs) in IAEA Member States. Operating experience has shown that ineffective control of the ageing degradation of the major NPP components (e.g., caused by unanticipated phenomena and by operating, maintenance or manufacturing errors) can jeopardize plant safety and also plant life. Ageing in these NPPs must be therefore effectively managed to ensure the availability of design functions throughout the plant service life. From the safety perspective, this means controlling within acceptable limits the ageing degradation and wear-out of plant components important to safety so that adequate safety margins remain, i.e. integrity and functional capability in excess of normal operating requirements. This TECDOC is one in a series of reports on the assessment and management of ageing of the major NPP components important to safety. The reports are based on experience and practices of NPP operators, regulators, designers, manufacturers and technical support organizations and a widely accepted Methodology for the Management of Ageing of NPP Components Important to Safety which was issued by the IAEA in 1992. The current practices for the assessment of safety margins (fitness-for-service) and the inspection, monitoring and mitigation of ageing degradation of selected components of Canada deuterium-uranium (CANDU) reactors, boiling water reactors (BWRs), pressurized water reactors (PWRs), including water moderated, water cooled energy reactors (WWERs) are documented in the reports. These practices are intended to help all involved directly and indirectly in ensuring the safe operation of NPPs; and also to provide a common technical basis for dialogue between plant operators and regulators when dealing with age related licensing issues. Since the reports are written from a safety perspective, they do not address life or life-cycle management of the plant components, which involves the integration of

Interaction of electromagnetic pulse with commercial nuclear-power-plant systems

Energy Technology Data Exchange (ETDEWEB)

Ericson, D.M. Jr.; Strawe, D.F.; Sandberg, S.J.; Jones, V.K.; Rensner, G.D.; Shoup, R.W.; Hanson, R.J.; Williams, C.B.

1983-02-01

This study examines the interaction of the electromagnetic pulse from a high altitude nuclear burst with commercial nuclear power plant systems. The potential vulnerability of systems required for safe shutdown of a specific nuclear power plant are explored. EMP signal coupling, induced plant response and component damage thresholds are established using techniques developed over several decades under Defense Nuclear Agency sponsorship. A limited test program was conducted to verify the coupling analysis technique as applied to a nuclear power plant. The results are extended, insofar as possible, to other nuclear plants.

Interaction of electromagnetic pulse with commercial nuclear-power-plant systems

International Nuclear Information System (INIS)

Ericson, D.M. Jr.; Strawe, D.F.; Sandberg, S.J.; Jones, V.K.; Rensner, G.D.; Shoup, R.W.; Hanson, R.J.; Williams, C.B.

1983-02-01

This study examines the interaction of the electromagnetic pulse from a high altitude nuclear burst with commercial nuclear power plant systems. The potential vulnerability of systems required for safe shutdown of a specific nuclear power plant are explored. EMP signal coupling, induced plant response and component damage thresholds are established using techniques developed over several decades under Defense Nuclear Agency sponsorship. A limited test program was conducted to verify the coupling analysis technique as applied to a nuclear power plant. The results are extended, insofar as possible, to other nuclear plants

Assessment and management of ageing of major nuclear power plant components important to safety: BWR pressure vessels

International Nuclear Information System (INIS)

2005-10-01

At present, there are over four hundred operational nuclear power plants (NPPs) in IAEA Member States. Operating experience has shown that ineffective control of the ageing degradation of the major NPP components (caused for instance by unanticipated phenomena and by operating, maintenance or manufacturing errors) can jeopardize plant safety and also plant life. Ageing in these NPPs must be therefore effectively managed to ensure the availability of design functions throughout the plant service life. From the safety perspective, this means controlling, within acceptable limits, the ageing degradation and wear out of plant components important to safety so that adequate safety margins remain, i.e. integrity and functional capability in excess of normal operating requirements. This TECDOC is one in a series of reports on the assessment and management of ageing of the major NPP components important to safety. The reports are based on experience and practices of NPP operators, regulators, designers, manufacturers and technical support organizations and a widely accepted Methodology for the Management of Ageing of NPP Components Important to Safety, which was issued by the IAEA in 1992. Since the reports are written from a safety perspective, they do not address life or life cycle management of plant components, which involves economic considerations. The current practices for the assessment of safety margins (fitness for service) and the inspection, monitoring and mitigation of ageing degradation of selected components of Canada deuterium-uranium (CANDU) reactors, boiling water reactors (BWRs), pressurized water reactors (PWRs), and water moderated, water cooled energy reactors (WWERs) are documented in the reports. These practices are intended to help all involved directly and indirectly in ensuring the safe operation of NPPs, and also to provide a common technical basis for dialogue between plant operators and regulators when dealing with age related licensing issues

Detection and mitigation of aging and service wear effects of nuclear power plant components in Canada

International Nuclear Information System (INIS)

Pachner, J.

1987-07-01

In Canada, the operational safety management of nuclear power plants employs methods which are intended to prevent, detect, correct and mitigate system and component failures from any cause, including the effects of aging and service wear degradation. The paper gives an overview of the application of these methods in the detection and mitigation of aging effects before they impact on plant safety and production reliability. Regulatory audits of these methods, to ensure that an acceptable level of plant safety is maintained by the nuclear power plant licensees, are also described. The methods are: a preventive maintenance program, Significant Event Reporting system, and a reliability based assessment of performance of safety related systems. The above methods are discussed and illustrated by examples. The soundness of the approach has been proven by the results achieved in 163 reactor-years of operation. Present and future developments include reviews of current monitoring, testing and inspection methods to ensure that appropriate time variant parameters (capable of revealing aging degradation before loss of functional capability) are monitored, and reviews of the effectiveness of existing maintenance programs and methods in mitigating aging and service wear effects

Diagnosing component faults in a generic nuclear power plant using counterfactual and temporal reasoning

International Nuclear Information System (INIS)

Oehrstroem, P.; Nielsen, F.R.; Pedersen, S.A.

1992-01-01

The subject of main interest is the logical and epistemological aspects of diagnostic reasoning. The aim was to understand the role of conditionals and causality in this respect. A model of causal and temporal reasoning was developed and evaluated in a controlled but complex setting. The generic nuclear power plant was used as a test ground. The coherence and scope of a logical theory of diagnostic reasoning was studied in order to discover whether the theory constitutes an adequate tool for making correct diagnoses of component faults in a generic nuclear power plant. A diagnosing system based on the CIMP system was run on a computer model of a nuclear power plant, various errors were then introduced. The aim of the diagnosis is mainly explanation and only partly repair. The causal field defines a conceptual framework within which the diagnostic purpose is given and within which various diagnostic possibilities and causal relationships are given, here with regard to error detection in a control room. The causal field is tacitly given and related to the operator's training and experience. The logical aspects of the problem of the diagnosis is described. The computer model is described and the symptom language is introduced. The process of reasoning about the possible diagnosis is presented. The utilization of ideas similiar to the heuristic classification is discussed. A data base command language for manipulating lists of symptoms is described and the design of a CIMP user interface for symptom language visualization is outlined. (AB)

RIBA Project - Risk-Informed approach for In-Service Inspection of Nuclear Power Plant Components. Project summary

International Nuclear Information System (INIS)

Lidbury, D.; Smith, G.

2001-12-01

The need for a European review of a Risk-Informed Approach for In-Service Inspection of Nuclear Power Plant Components (RIBA) was identified in 1998. This was as a priority item in the programme of activities conducted in the framework of the Council Resolutions of 22 July 1975 and of 18 June 1992 on the Technological Problems of Nuclear Safety. The RIBA Project was established in November 1999 as a 24-month Study Contract funded by the European Commission within the frame of the former DG XI WGCS (Working Group on Codes and Standards). The Study Contract was subsequently managed for the EC by DG TREN. The participants in RIBA were Serco Assurance (project coordinator), Ringhals AB, EDF, Tecnatom SA and Westinghouse Electric Europe. The work is presented in a summary report with the detailed results contained in three companion reports as follows: main conclusions and recommendations, Review of Existing Risk-Informed Methodologies, A Comparative Study of Risk-Informed In-Service Inspection Applications, Conclusions and Recommendations for Risk-Informed in-service inspection methodology applied to Nuclear Power Plants in Europe. (author)

DSNP: a new approach to simulate nuclear power plants

International Nuclear Information System (INIS)

Saphier, D.

1977-01-01

The DSNP (Dynamic Simulator for Nuclear Power-plants) is a special purpose block oriented simulation language. It provides for simulations of a large variety of nuclear power plants or various parts of the power plant in a simple straightforward manner. The system is composed of five basic elements, namely, the DSNP language, the precompiler-or the DSNP language translator, the components library, the document generator, and the system data files. The DSNP library of modules includes the selfcontained models of components or physical processes found in a nuclear power plant, and various auxiliary modules such as material properties, control modules, integration schemes, various basic transfer functions etc. In its final form DSNP will have four libraries

Evaluation of Component Failure Data of the Operating Nuclear Power Plants in Korea Based on NUREG/CR-6928

International Nuclear Information System (INIS)

Jeon, Hojun; Na, Janghwan; Shin, Taeyoung

2014-01-01

This paper focuses on ensuring the quality of component failure data. When performing data analysis in PSA, we have customized the component failure data based on Bayesian analysis using plant specific experiences and the generic data of Advanced Light Water Reactor Utility Requirements Document (ALWR URD). However, ALWR URD was established by collecting US nuclear power plant (NPP) practices from mid 1980s to early 1990s. We analyzed the component failure data using the raw data of component failures in Pressurized Water Reactor (PWR) plants by 2012. This paper presents the results from analyzing the component failure data based on the new generic data and the latest specific failure data. We also compare the new component failure data to the existing data of PSA models, and evaluate the risk impacts by applying the new data to the PSA models of reference NPPs in this paper. To apply the new generic data source to PSA models, we reviewed and compared NUREG/CR-6928 and the existing generic data source, ALWR URD. In addition, we analyzed the component failure data generated from 16 PWR plants by the end of 2012, and performed the Bayesian update with these raw data based on the new generic data source of NUREG/CR-6928. Also, we reviewed the PSA models of the reference NPP, and identified some important components to CDF. The failure data of the major components decreased in general by applying the new generic data and the latest plant specific data. As a result, the CDF of the reference NPP decreased over 30% compared to the value of the existing CDF

Effect of operating conditions and environment on properties of materials of PWR type nuclear power plant components

International Nuclear Information System (INIS)

Vacek, M.

1987-01-01

Operating reliability and service life of PWR type nuclear power plants are discussed with respect to the material properties of the plant components. The effects of the operating environment on the material properties and the methods of their determination are characterized. Discussed are core materials, such as fuel, its cladding and regulating rod materials, and the materials of pipes, steam generators and condensers. The advances in the production of pressure vessel materials and their degradation during operation are treated in great detail. (Z.M.)

Requirements for class 1C, 2C, and 3C pressure-retaining components and supports in CANDU nuclear power plants

International Nuclear Information System (INIS)

1989-01-01

This Standard applies to pressure-retaining components of CANDU nuclear power plants that have a code classification of Class 1C, 2C or 3C. These are pressure-retaining components where, because of the design concept, the rules of the ASME Boiler and Pressure Vessel Code do not exist, are not applicable, or are not sufficient. The Standard provides rules for the design, fabrication, installation, examination and inspection of these components and supports. It provides rules intended to ensure the pressure-retaining integrity of components, not the operability. It also provides rules for the support of fueling machines. The Standard applies only to new construction prior to the plant being declared in service

Development of integrity evaluation technology for pressurized components in nuclear power plant and IT based integrity evaluation system

International Nuclear Information System (INIS)

Kim, Young Jin; Choi, Jae Boong; Shim, Do Jun

2004-02-01

The objective of this research is to develop on efficient integrity evaluation technology and to investigate the applicability of the newly-developed technology such as internet-based cyber platform etc. to Nuclear Power Plant(NPP) components. The development of an efficient structural integrity evaluation system is necessary for safe operation of NPP as the increase of operating periods. Moreover, material test data as well as emerging structural integrity assessment technology are also needed for the evaluation of aged components. The following five topics are covered in this project: development of the wall-thinning evaluation program for nuclear piping; development of structural integrity evaluation criteria for steam generator tubes with cracks of various shape; development of fatigue life evaluation system for major components of NPP; ingegration of internet-based cyber platform and integrity evaluation program for primary components of NPP; effects of aging on strength of dissimilar welds

Development of integrity evaluation technology for pressurized components in nuclear power plant and IT based integrity evaluation system

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Jin; Choi, Jae Boong; Shim, Do Jun [Sungkyunkwan Univ., Seoul (Korea, Republic of)] (and others)

2004-02-15

The objective of this research is to develop on efficient integrity evaluation technology and to investigate the applicability of the newly-developed technology such as internet-based cyber platform etc. to Nuclear Power Plant(NPP) components. The development of an efficient structural integrity evaluation system is necessary for safe operation of NPP as the increase of operating periods. Moreover, material test data as well as emerging structural integrity assessment technology are also needed for the evaluation of aged components. The following five topics are covered in this project: development of the wall-thinning evaluation program for nuclear piping; development of structural integrity evaluation criteria for steam generator tubes with cracks of various shape; development of fatigue life evaluation system for major components of NPP; ingegration of internet-based cyber platform and integrity evaluation program for primary components of NPP; effects of aging on strength of dissimilar welds.

Friction and wear studies of nuclear power plant components in pressurized high temperature water environments

International Nuclear Information System (INIS)

Ko, P.L.; Zbinden, M.; Taponat, M.C.; Robertson, M.F.

1997-01-01

The present paper is part of a series of papers aiming to present the friction and wear results of a collaborative study on nuclear power plant components tested in pressurized high temperature water. The high temperature test facilities and the methodology in presenting the kinetics and wear results are described in detail. The results of the same material combinations obtained from two very different high temperature test facilities (NRCC and EDF) are presented and discussed. (K.A.)

Space nuclear reactor power plants

International Nuclear Information System (INIS)

Buden, D.; Ranken, W.A.; Koenig, D.R.

1980-01-01

Requirements for electrical and propulsion power for space are expected to increase dramatically in the 1980s. Nuclear power is probably the only source for some deep space missions and a major competitor for many orbital missions, especially those at geosynchronous orbit. Because of the potential requirements, a technology program on space nuclear power plant components has been initiated by the Department of Energy. The missions that are foreseen, the current power plant concept, the technology program plan, and early key results are described

Security Hardened Cyber Components for Nuclear Power Plants: Phase I SBIR Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Franusich, Michael D. [SpiralGen, Inc., Pittsburgh, PA (United States)

2016-03-18

SpiralGen, Inc. built a proof-of-concept toolkit for enhancing the cyber security of nuclear power plants and other critical infrastructure with high-assurance instrumentation and control code. The toolkit is based on technology from the DARPA High-Assurance Cyber Military Systems (HACMS) program, which has focused on applying the science of formal methods to the formidable set of problems involved in securing cyber physical systems. The primary challenges beyond HACMS in developing this toolkit were to make the new technology usable by control system engineers and compatible with the regulatory and commercial constraints of the nuclear power industry. The toolkit, packaged as a Simulink add-on, allows a system designer to assemble a high-assurance component from formally specified and proven blocks and generate provably correct control and monitor code for that subsystem.

Nuclear power plant life management. An overview of identification of key components in relation with degradation mechanism - IAEA guidelines presentation

International Nuclear Information System (INIS)

Bezdikian, Georges

2005-01-01

Nuclear Power Plant (NPP) lifetime has a direct bearing on the cost of the electricity generated from it. The annual unit cost of electricity is dependent upon the operational time, and also annual costs and the capital cost assumptions function of Euros/kw. If the actual NPP lifetime has been underestimated then an economic penalty could be incurred. But the ageing degradation, of nuclear power plants is an important aspect that requires to be addressed to ensure: - that necessary safety margins are maintained throughout service life; - the adequate reliability and therefore the economic viability of older plants is maintained; - that unforeseen an uncontrolled degradation of critical plant components does not foreshorten the plant lifetime. Accommodating the inevitable obsolescence of some components has also to be addressed during plant life. Plant lifetime management requires the identification and life assessment of those components which not only limit the lifetime of the plant but also those which cannot be reasonably replaced. The planned replacement of major or 'key' components needs to be considered - where economic considerations will largely dictate replacement or the alternative strategy of power plant decommissioning. The necessary but timely planning for maintenance and replacements is a necessary consideration so that functions and reliability are maintained. The reasons for the current increasing attention in the area of plant life management are diverse and range from the fact that many of the older plants are approaching for the oldest plants more than 30 years in operation, and for important number of NPPs between 20 and 30 years. The impact of plant life management on the economics of generating electricity is the subject of ongoing studies and it can readily be seen that there can be both savings and additional costs associated with these activities. Not all degradation processes will be of significance in eroding safety margins and there is a

Nuclear power plants

International Nuclear Information System (INIS)

1985-01-01

Data concerning the existing nuclear power plants in the world are presented. The data was retrieved from the SIEN (Nuclear and Energetic Information System) data bank. The information are organized in table forms as follows: nuclear plants, its status and type; installed nuclear power plants by country; nuclear power plants under construction by country; planned nuclear power plants by country; cancelled nuclear power plants by country; shut-down nuclear power plants by country. (E.G.) [pt

HTGR nuclear heat source component design and experience

International Nuclear Information System (INIS)

Peinado, C.O.; Wunderlich, R.G.; Simon, W.A.

1982-05-01

The high-temperature gas-cooled reactor (HTGR) nuclear heat source components have been under design and development since the mid-1950's. Two power plants have been designed, constructed, and operated: the Peach Bottom Atomic Power Station and the Fort St. Vrain Nuclear Generating Station. Recently, development has focused on the primary system components for a 2240-MW(t) steam cycle HTGR capable of generating about 900 MW(e) electric power or alternately producing high-grade steam and cogenerating electric power. These components include the steam generators, core auxiliary heat exchangers, primary and auxiliary circulators, reactor internals, and thermal barrier system. A discussion of the design and operating experience of these components is included

Structural analysis of nuclear components

International Nuclear Information System (INIS)

Ikonen, K.; Hyppoenen, P.; Mikkola, T.; Noro, H.; Raiko, H.; Salminen, P.; Talja, H.

1983-05-01

THe report describes the activities accomplished in the project 'Structural Analysis Project of Nuclear Power Plant Components' during the years 1974-1982 in the Nuclear Engineering Laboratory at the Technical Research Centre of Finland. The objective of the project has been to develop Finnish expertise in structural mechanics related to nuclear engineering. The report describes the starting point of the research work, the organization of the project and the research activities on various subareas. Further the work done with computer codes is described and also the problems which the developed expertise has been applied to. Finally, the diploma works, publications and work reports, which are mainly in Finnish, are listed to give a view of the content of the project. (author)

Seismic fragility of nuclear power plant components (Phase II)

International Nuclear Information System (INIS)

Bandyopadhyay, K.K.; Hofmayer, C.H.; Kassir, M.K.; Pepper, S.E.

1990-02-01

As part of the Component Fragility Program which was initiated in FY 1985, three additional equipment classes have been evaluated. This report contains the fragility results and discussions on these equipment classes which are switchgear, I and C panels and relays. Both low and medium voltage switchgear assemblies have been considered and a separate fragility estimate for each type is provided. Test data on cabinets from the nuclear instrumentation/neutron monitoring system, plant/process protection system, solid state protective system and engineered safeguards test system comprise the BNL data base for I and C panels (NSSS). Fragility levels have been determined for various failure modes of switchgear and I ampersand C panels, and the deterministic results are presented in terms of test response spectra. In addition, the test data have been evaluated for estimating the respective probabilistic fragility levels which are expressed in terms of a median value, an uncertainty coefficient, a randomness coefficient and an HCLPF value. Due to a wide variation of relay design and the fragility level, a generic fragility level cannot be established for relays. 7 refs., 13 figs., 12 tabs

Nuclear power plant decommissioning

International Nuclear Information System (INIS)

Yaziz Yunus

1986-01-01

A number of issues have to be taken into account before the introduction of any nuclear power plant in any country. These issues include reactor safety (site and operational), waste disposal and, lastly, the decommissioning of the reactor inself. Because of the radioactive nature of the components, nuclear power plants require a different approach to decommission compared to other plants. Until recently, issues on reactor safety and waste disposal were the main topics discussed. As for reactor decommissioning, the debates have been academic until now. Although reactors have operated for 25 years, decommissioning of retired reactors has simply not been fully planned. But the Shippingport Atomic Power Plant in Pennysylvania, the first large scale power reactor to be retired, is now being decommissioned. The work has rekindled the debate in the light of reality. Outside the United States, decommissioning is also being confronted on a new plane. (author)

Online condition monitoring to enable extended operation of nuclear power plants

International Nuclear Information System (INIS)

Meyer, Ryan Michael; Bond, Leonard John; Ramuhalli, Pradeep

2012-01-01

Safe, secure, and economic operation of nuclear power plants will remain of strategic significance. New and improved monitoring will likely have increased significance in the post-Fukushima world. Prior to Fukushima, many activities were already underway globally to facilitate operation of nuclear power plants beyond their initial licensing periods. Decisions to shut down a nuclear power plant are mostly driven by economic considerations. Online condition monitoring is a means to improve both the safety and economics of extending the operating lifetimes of nuclear power plants, enabling adoption of proactive aging management. With regard to active components (e.g., pumps, valves, motors, etc.), significant experience in other industries has been leveraged to build the science base to support adoption of online condition-based maintenance and proactive aging management in the nuclear industry. Many of the research needs are associated with enabling proactive management of aging in passive components (e.g., pipes, vessels, cables, containment structures, etc.). This paper provides an overview of online condition monitoring for the nuclear power industry with an emphasis on passive components. Following the overview, several technology/knowledge gaps are identified, which require addressing to facilitate widespread online condition monitoring of passive components. (author)

Different aspects of safety in Nuclear Fuel Plant at Pitesti, Romania

International Nuclear Information System (INIS)

Ivana, T.; Epure, Gh.

2009-01-01

Nuclear Fuel Plant (FCN) is a facility that produces fuel bundles of CANDU-6 type for the CANDU nuclear power plant. Only natural and depleted uranium in bulk and itemized form are present as nuclear materials in this facility. Uranium and wastes from the plant are handled, processed, treated and stored throughout the entire facility. The nuclear materials with natural and depleted uranium are entirely under nuclear safeguards. The amount of uranium present in the plant in different forms and activities together with zircaloy, beryllium and other hazardous substances, wastes, explosive materials at high temperatures, etc. lead to special measures undertaken by Nuclear Safety Department (DNS) to ensure nuclear safety. Different aspects of safety are continuously monitored in the plant: operational safety, industrial safety, radiological safety, labour safety, informational safety. The emergency preparedness and response, physical protection and the security of the plant and of the transportation of radioactive materials are contributing to cover the multitude of safety aspects. The safety culture of workers built directly on the safety components completes this activity in the plant. In addition the aspects of safety, security and safeguards are in permanent synergy, parts of the three components being included in each other. In the future the policy of FCN will be focused so that any improvement of one of the safety components will be reflected in improving the other safety aspects. (authors)

Plant life management optimized utilization of existing nuclear power plants

International Nuclear Information System (INIS)

Watzinger, H.; Erve, M.

1999-01-01

For safe, reliable and economical nuclear power generation it is of central importance to understand, analyze and manage aging-related phenomena and to apply this information in the systematic utilization and as-necessary extension of the service life of components and systems. An operator's overall approach to aging and plant life management which also improves performance characteristics can help to optimize plant operating economy. In view of the deregulation of the power generation industry with its increased competition, nuclear power plants must today also increasingly provide for or maintain a high level of plant availability and low power generating costs. This is a difficult challenge even for the newest, most modern plants, and as plants age they can only remain competitive if a plant operator adopts a strategic approach which takes into account the various aging-related effects on a plant-wide basis. The significance of aging and plant life management for nuclear power plants becomes apparent when looking at their age: By the year 2000 roughly fifty of the world's 434 commercial nuclear power plants will have been in operation for thirty years or more. According to the International Atomic Energy Agency, as many as 110 plants will have reached the thirty-year service mark by the year 2005. In many countries human society does not push the construction of new nuclear power plants and presumably will not change mind within the next ten years. New construction licenses cannot be expected so that for economical and ecological reasons existing plants have to be operated unchallengeably. On the other hand the deregulation of the power production market is asking just now for analysis of plant life time to operate the plants at a high technical and economical level until new nuclear power plants can be licensed and constructed. (author)

Reduction of capital costs of nuclear power plants. NEA-report

International Nuclear Information System (INIS)

2000-01-01

Since the the mid-1980s, the declining real prices of fossil fuels and the significant improvements in thermal efficiencies of combined cycle power plants have eroded the economic competitiveness of nuclear power plants in most OECD countries. In order for nuclear power to remain a viable option for the next millennium, the cost of electricity from nuclear power plant must be greatly reduced to be competitive with alternative sources. Of the three major components of nuclear generation cost - capital, O and M and fuel - the capital cost component makes up approximately 60 per cent of the total. Therefore, identification of the means to reduce the capital costs of nuclear power plants is a high priority activity toward keeping nuclear power competitive. Among a number of capital cost reduction measures, the principal ones were agreed by the expert group as follows: Increased plant size, improved construction methods, reduced construction schedule, design improvement, improved procurement, organisation and contractual aspects, standardisation and construction in series, multiple unit construction, regulatory and policy reform. (orig.)

Nuclear plant life cycle costs

International Nuclear Information System (INIS)

Durante, R.W.

1994-01-01

Life cycle costs of nuclear power plants in the United States are discussed. The author argues that these costs have been mishandled or neglected. Decommissioning costs have escalated, e.g. from $328 per unit in 1991 to $370 in 1993 for the Sacramento Municipal Utility District, though they still only amount to less than 0.1 cent per kWh. Waste management has been complicated in the U.S. by the decision to abandon civilian reprocessing; by the year 2000, roughly 30 U.S. nuclear power units will have filled their storage pools; dry storage has been delayed, and will be an expense not originally envisaged. Some examples of costs of major component replacement are provided. No single component has caused as much operational disruption and financial penalties as the steam generator. Operation and maintenance costs have increased steadily, and now amount to more than 70% of production costs. A strategic plan by the Nuclear Power Oversight Committee (of U.S. utilities) will ensure that the ability to correctly operate and maintain a nuclear power plant is built into the original design. 6 figs

NUCLEBRAS' installations for tests of nuclear power plants components

International Nuclear Information System (INIS)

Vasconcelos Paiva, I.P. de; Horta, J.A.L.; Avelar Esteves, F. de; Pinheiro, R.B.

1983-05-01

The reasons for NUCLEBRAS' Nuclear Technology Development Center to implement a laboratory for supporting Brazilian manufacturers, giving to them the means for performing functional tests of industrial products, are presented. A brief description of the facilities under construction: the Components Test Loop and the Facility for Testing N.P.P. Components under Accident Conditions, and of other already in operation, is given, as well as its objectives and main technical characteristics. Some test results already obtained are also presented. (Author) [pt

Operation of Finnish nuclear power plants

International Nuclear Information System (INIS)

Tossavainen, K.

1993-12-01

Quarterly reports on the operation of Finnish nuclear power plants describe events and observations related to nuclear and radiation safety which the Finnish Centre for Radiation and Nuclear Safety considers safety significant. Safety-enhancing plant modifications and general matters relating to the use of nuclear energy are also reported. A summary of the radiation safety of plant personnel and the environment, and tabulated data on the plants' production and their load factors are also given. At the Loviisa 1 plant unit one of two specially-backed AC busbars was lost during the second quarter of 1993. A ca. 30 minute voltage break caused malfunctions in the plant unit's electrical equipment and rendered inoperable certain components important to safety. The event is rated on the International Nuclear Event Scale (INES) at level 1. In inspections carried out at TVO II during the annual maintenance outage, the number of cracks detected in control rod structural material was higher than usual. When cracks occur, part of boron carbide, the power regulating medium in control rods, may wash into the reactor water and control rod shutdown capability may be impaired. The event is rated on the INES at level 1. Other events in the second quarter of 1993 had no bearing on nuclear or radiation safety. (4 figs., 5 tabs.)

Assessment and management of ageing of major nuclear power plant components important to safety: BWR pressure vessel internals

International Nuclear Information System (INIS)

2005-10-01

At present, there are over four hundred operational nuclear power plants (NPPs) in IAEA Member States. Operating experience has shown that ineffective control of the ageing degradation of the major NPP components (caused for instance by unanticipated phenomena and by operating maintenance or manufacturing errors) can jeopardize plant safety and also plant life. Ageing in these NPPs must be therefore effectively managed to ensure the availability of design functions throughout the plant service life. From the safety perspective, this means controlling, within acceptable limits, the ageing degradation and ware out of components important to safety so that adequate safety margins remain, i.e. integrity and functional capability in excess of normal operating requirements. This TECDOC is one in a series of guidance reports on the assessment and management of ageing of the major NPP components important to safety. The reports are based on experience and practices of NPP operators, regulators, designers, manufacturers, and technical support organizations and a widely accepted Methodology for the Management of Ageing of NPP Components Important to Safety, which was issued by the IAEA in 1992. Since the reports are written from a safety perspective, they do not address life or life cycle management of plant components, which involves economic considerations. The current practices for the assessment of safety margins (fitness for service) and the inspection, monitoring and mitigation of ageing degradation of selected components of heavy water moderated reactors (HWRs), boiling water reactors (BWRs), pressurized water reactors (PWRs), and water moderated, water cooled energy reactors (WWERs) are documented in the reports. These practices are intended to help all involved directly and indirectly in ensuring the safe operation of NPPs, and also to provide a common technical basis for dialogue between plant operators and regulators when dealing with age related licensing issues

Availability Improvement of German Nuclear Power Plants

International Nuclear Information System (INIS)

Wilhelm, Oliver

2008-01-01

High availability is important for the safety and economical performance of Nuclear Power Plants (NPP). The strategy for availability improvement in a typical German PWR shall be discussed here. Key parameters for strategy development are plant design, availability of safety systems, component reliability, preventive maintenance and outage organization. Plant design, availability of safety systems and component reliability are to a greater extent given parameters that can hardly be influenced after the construction of the plant. But they set the frame for maintenance and outage organisation which have shown to have a large influence on the availability of the plant. (author)

Health protection and industrial safety. Nuclear power plants

International Nuclear Information System (INIS)

1987-03-01

The standard applies to components of the primary circuit including its auxiliary facilities, and of the secondary circuit of nuclear power plants with pressurized water reactors; to lifting gear and load take-ups for the transport of nuclear fuel and primary circuit components, and to elevators within the containment. Part 2 specifies testing, test periods, test methods, and documentation

The Role of Nuclear Power Plants in the Development of a Country

International Nuclear Information System (INIS)

Cintra do Prado, L.

1966-01-01

Nuclear power plants oan contribute to the economic development of a country in two ways - as generators of power and as stimuli for the growth of new national industries. Some countries build nuclear power plants because other sources of cheap power are lacking. Other countries engage in nuclear activities such as the production of nuclear components and the purification of reactor materials before there is an immediate need for nuclear power in an attempt to plan for future national requirements and to create a nuclear export industry. A country can also import all or nearly all the components needed for the construction of nuclear power plants. In this case the importing country enjoys the benefits of facilities generating power without the advantages of a national nuclear industry. Industrialised countries generally find this solution undesirable save in exceptional circumstances, for example in the initial stages of a nuclear programme or in the case of specific nuclear components. Developing countries can also aim at a phased introduction of nuclear energy and try to combine the advantages of nuclear power production and the development of a national nuclear industry. Thus, in addition to the inherent advantages of nuclear plants as sources of electricity there are various ways in which the establishment of such plants can stimulate industry, namely through the use of nuclear and other ores utilizable in reactors, the promotion of ore-exploration activities, and the development of transformation industries

The Role of Nuclear Power Plants in the Development of a Country

Energy Technology Data Exchange (ETDEWEB)

Cintra do Prado, L. [Brazilian Nuclear Energy Commission (Brazil)

1966-07-01

Nuclear power plants oan contribute to the economic development of a country in two ways - as generators of power and as stimuli for the growth of new national industries. Some countries build nuclear power plants because other sources of cheap power are lacking. Other countries engage in nuclear activities such as the production of nuclear components and the purification of reactor materials before there is an immediate need for nuclear power in an attempt to plan for future national requirements and to create a nuclear export industry. A country can also import all or nearly all the components needed for the construction of nuclear power plants. In this case the importing country enjoys the benefits of facilities generating power without the advantages of a national nuclear industry. Industrialised countries generally find this solution undesirable save in exceptional circumstances, for example in the initial stages of a nuclear programme or in the case of specific nuclear components. Developing countries can also aim at a phased introduction of nuclear energy and try to combine the advantages of nuclear power production and the development of a national nuclear industry. Thus, in addition to the inherent advantages of nuclear plants as sources of electricity there are various ways in which the establishment of such plants can stimulate industry, namely through the use of nuclear and other ores utilizable in reactors, the promotion of ore-exploration activities, and the development of transformation industries.

Knowledge management for the decommissioning of nuclear power plants

International Nuclear Information System (INIS)

Kirschnick, F.; Engelhardt, S.

2004-01-01

This paper describes background, objectives and select conceptual components of knowledge management for the decommissioning of nuclear power plants. The concept focuses on the transfer of personal practice experience within and between nuclear power plants. The conceptual insights embrace aspects of knowledge content, structure, KM processes, organization, cooperation, culture, persuasion, leadership, technology, infrastructure, business impact and resilience. Key challenges are discussed, and related advice is provided for KM practitioners with similar endeavours in the field of nuclear power plant decommissioning. (author)

Planned reliability in the transport and installation of large nuclear components

International Nuclear Information System (INIS)

Bieler, L.

1988-01-01

The transport and installation of heavy and bulky large components require detailed planning of all jobs and activities, trained and experienced personnel and corresponding technical equipment for reliable and quality-assured implementation. The correct approach to the planning and implementation of such transports and installations has been confirmed by years of successful performance of these jobs e.g. in reactor pressure vessels and steam generators for nuclear power plants. Large components for nuclear power plants are truly extreme examples but will be all the better suited for demonstrating the problems inherent in transport and installation. (orig.) [de

Seismic design of nuclear power plants - an assessment

International Nuclear Information System (INIS)

Howard, G.E.; Ibanez, P.; Smith, C.B.

1976-01-01

This paper presents a review and evaluation of the design standards and the analytical and experimental methods used in the seismic design of nuclear power plants with emphasis on United States practice. Three major areas were investigated: (a) soils, siting, and seismic ground motion specification; (b) soil-structure interaction; and (c) the response of major nuclear power plant structures and components. The purpose of this review and evaluation program was to prepare an independent assessment of the state-of-the-art of the seismic design of nuclear power plants and to identify seismic analysis and design research areas meriting support by the various organizations comprising the 'nuclear power industry'. Criteria used for evaluating the relative importance of alternative research areas included the potential research impact on nuclear power plant siting, design, construction, cost, safety, licensing, and regulation. (Auth.)

Assessment and management of ageing of major nuclear power plant components important to safety. Primary piping in PWRs

International Nuclear Information System (INIS)

2003-07-01

At present, there are over four hundred operational nuclear power plants (NPPs) in IAEA Member States. Operating experience has shown that ineffective control of the ageing degradation of the major NPP components (caused for instance by unanticipated phenomena and by operating, maintenance or manufacturing errors) can jeopardize plant safety and also plant life. Ageing in these NPPs must therefore be effectively managed to ensure the availability of design functions throughout the plant service life. From the safety perspective, this means controlling, within acceptable limits, the ageing degradation and wear out of plant components important to safety so that adequate safety margins remain, i.e. integrity and functional capability in excess of normal operating requirements. This TECDOC is one in a series of reports on the assessment and management of ageing of the major NPP components important to safety. The reports are based on experience and practices of NPP operators, regulators, designers, manufacturers, technical support organizations and a widely accepted Methodology for the Management of Ageing of NPP Components Important to Safety, which was issued by the IAEA in 1992. Since the reports are written from a safety perspective, they do not address life or life cycle management of plant components, which involves economic considerations. The current practices for the assessment of safety margins (fitness-for-service) and the inspection, monitoring and mitigation of ageing degradation of selected components of Canada deuterium-uranium (CANDU) reactors, boiling water reactors (BWRs), pressurized water reactors (PWRs), and water moderated, water cooled energy reactors (WWERs) are documented in the reports. These practices are intended to help all involved directly and indirectly in ensuring the safe operation of NPPs, and to provide a common technical basis for dialogue between plant operators and regulators when dealing with age-related licensing issues. The

Nuclear Plant Aging Research (NPAR) program plan

International Nuclear Information System (INIS)

1991-06-01

A comprehensive Nuclear Plant Aging Research (NPAR) Program was implemented by the US NRC office of Nuclear Regulatory Research in 1985 to identify and resolve technical safety issues related to the aging of systems, structures, and components in operating nuclear power plants. This is Revision 2 to the Nuclear Plant Aging Research Program Plant. This planes defines the goals of the program the current status of research, and summarizes utilization of the research results in the regulatory process. The plan also describes major milestones and schedules for coordinating research within the agency and with organizations and institutions outside the agency, both domestic and foreign. Currently the NPAR Program comprises seven major areas: (1) hardware-oriented engineering research involving components and structures; (2) system-oriented aging interaction studies; (3) development of technical bases for license renewal rulemaking; (4) determining risk significance of aging phenomena; (5) development of technical bases for resolving generic safety issues; (6) recommendations for field inspection and maintenance addressing aging concerns; (7) and residual lifetime evaluations of major LWR components and structures. The NPAR technical database comprises approximately 100 NUREG/CR reports by June 1991, plus numerous published papers and proceedings that offer regulators and industry important insights to aging characteristics and aging management of safety-related equipment. Regulatory applications include revisions to and development of regulatory guides and technical specifications; support to resolve generic safety issues; development of codes and standards; evaluation of diagnostic techniques; (e.g., for cables and valves); and technical support for development of the license renewal rule. 80 refs., 25 figs., 10 tabs

Information Technology for Nuclear Power Plant Configuration Management

International Nuclear Information System (INIS)

2010-07-01

Configuration management (CM) is an essential component of nuclear power plant design, construction and operation. The application of information technology (IT) offers a method to automate and ensure the timely and effective capture, processing and distribution of key nuclear power plant information to support CM principles and practical processes and procedures for implementation of CM at nuclear power plants. This publication reviews some of the principles established in IAEA-TECDOC-1335, 'Configuration Management in Nuclear Power Plants.' It also recaps tenets laid out in IAEA- TECDOC-1284, 'Information Technology Impact on Nuclear Power Plant Documentation' that supports CM programmes. This publication has been developed in conjunction with and designed to support these other two publications. These three publications combined provide a comprehensive discussion on configuration management, information technology and the relationship between them. An extensive discussion is also provided in this publication on the role of the design basis of the facility and its control through the CM process throughout the facility's lifetime. While this report was developed specifically for nuclear power plants, the principles discussed can be usefully applied to any high hazard nuclear facility

Fatigue analysis for analytically overloaded piping components and valves in nuclear power plants

International Nuclear Information System (INIS)

Charalambus, B.

1992-01-01

Lately, in connection with life extension aspects of power plants, an increasingly accurate determination of the lifetime of components in nuclear stations is being required. In order to assess reliably current fatigue levels in piping systems, variables such as pressure, temperature, and resultant force and moment transients as well as analytical methods which take into account the real operational history must be considered. This paper presents a method for analyzing the transient heat transfer between fluid and pipe wall in order to investigate effects which until now have been assumed conservatively to be caused by a sudden jump in temperature. Further, an example is given showing that the K e factor approach in current design codes for performing simplified elastic-plastic fatigue analyses is conservative. (orig.)

Seismic safety of nuclear power plants

International Nuclear Information System (INIS)

Guerpinar, A.; Godoy, A.

2001-01-01

This paper summarizes the work performed by the International Atomic Energy Agency in the areas of safety reviews and applied research in support of programmes for the assessment and enhancement of seismic safety in Eastern Europe and in particular WWER type nuclear power plants during the past seven years. Three major topics are discussed; engineering safety review services in relation to external events, technical guidelines for the assessment and upgrading of WWER type nuclear power plants, and the Coordinated Research Programme on 'Benchmark study for the seismic analysis and testing of WWER type nuclear power plants'. These topics are summarized in a way to provide an overview of the past and present safety situation in selected WWER type plants which are all located in Eastern European countries. Main conclusion of the paper is that although there is now a thorough understanding of the seismic safety issues in these operating nuclear power plants, the implementation of seismic upgrades to structures, systems and components are lagging behind, particularly for those cases in which the re-evaluation indicated the necessity to strengthen the safety related structures or install new safety systems. (author)

Reliability Data Handbook for Piping Components in Nordic Nuclear Power Plants - R Book, Phase 2

International Nuclear Information System (INIS)

Hedtjaern Swaling, Vidar; Olsson, Anders

2011-02-01

This report presents results of a long research and development project financed by the regulatory body Straalsaekerhetsmyndigheten (SSM) (former SKI), the Swedish nuclear power plant licensees. The report presents a harmonized method for estimating Reliability Data for Piping Components in ASME code class 1 and 2 piping components (R-Book). Data in the R-Book is measured based on 'data driven' strategy. This first version of the R-Book comprises rupture frequencies and failure rates for all systems where ASME Code Class 1 or 2 events could be found in the OECD OPDE database. Nordic and Non-Nordic data are presented separately. Worldwide experience data is used to set up the relevant calculation cases, i.e. intersections of attributes for which there are at least one event present

On-site tests on the nuclear power plants

International Nuclear Information System (INIS)

Morilhat, P.; Favennec, J.M.; Neau, P.; Preudhomme, E.

1996-01-01

On-site tests and experiments are performed by EDF Research and Development Division on the nuclear power plants to assess the behaviour of major components submitted to thermal and vibratory solicitations. On-going studies deal with the qualification of new nuclear power plant standard and with the feedback of plants under operation. The tests, particularly the investigation tests, correspond to large investments and entail an important data volume which must ensure the continuity over a long period of the order of magnitude of the in-service plant life (around 40 years). This paper addresses the on-site experimental activities, describes the means to be used, and gives an example: the qualification of SG of new 1450 MW nuclear power plants. (author)

Surveillance of items important to safety in nuclear power plants

International Nuclear Information System (INIS)

1990-01-01

The Guide was prepared as part of the IAEA's programme, referred to as the NUSS Programme, for establishing Codes and Safety Guides relating to nuclear power plants. THe Guide supplements the Code on the Safety of Nuclear Power Plants: Operation, IAEA Safety Series No. 50-C-O(Rev.1). The operating organization has overall responsibility for the safe operation of the nuclear power plant. Therefore, it shall ensure that adequate surveillance activities are carried out in order to verify that the plant is operated within the prescribed operational limits and conditions, and to detect in time any deterioration of structures, systems and components as well as any adverse trend that could lead to an unsafe condition. These activities can be classified as: Monitoring plant parameters and system status; Checking and calibrating instrumentation; Testing and inspecting structures, systems and components. This Safety Guide provides guidance and recommendations on surveillance activities to ensure that structures, systems and components important to safety are available to perform their functions in accordance with design intent and assumptions

CANDU 9 nuclear power plant simulator

International Nuclear Information System (INIS)

Kattan, M.; MacBeth, M.J.; Lam, K.

1995-01-01

Simulators are playing, an important role in the design and operations of CANDU reactors. They are used to analyze operating procedures under standard and upset conditions. The CANDU 9 nuclear power plant simulator is a low fidelity, near full scope capability simulator. It is designed to play an integral part in the design and verification of the control centre mock-up located in the AECL design office. It will also provide CANDU plant process dynamic data to the plant display system (PDS), distributed control system (DCS) and to the mock-up panel devices. The simulator model employs dynamic mathematical models of the various process and control components that make up a nuclear power plant. It provides the flexibility to add, remove or update user supplied component models. A block oriented process input is provided with the simulator. Individual blocks which represent independent algorithms of the model are linked together to generate the required overall plant model. As a design tool the simulator will be used for control strategy development, human factors studies (information access, readability, graphical display design, operability), analysis of overall plant control performance, tuning estimates for major control loops and commissioning strategy development. As a design evaluation tool, the simulator will be used to perform routine and non-routine procedures, practice 'what if' scenarios for operational strategy development, practice malfunction recovery procedures and verify human factors activities. This paper will describe the CANDU 9 plant simulator and demonstrate its implementation and proposed utility as a tool in the control system and control centre design of a CANDU 9 nuclear power plant. (author). 2 figs

Some methods of analysis and diagnostics of corroded components from nuclear power plant

International Nuclear Information System (INIS)

Mogosan, S.; Radulescu, M.; Fulger, M.; Stefanescu, D.

2010-01-01

In Nuclear Power Plants (NPP) it is necessary to ensure a longer and safe operation as difficult and expensive it is the maintenance of these very complex installations and equipment. In this regard, The Analysis and Diagnostic Laboratory Corroded Metal Components in Nuclear Facilities-LADICON; was authorized RENAR and CNCAN (National Commission for Nuclear Activities Control) notified as a testing laboratory for nuclear-grade materials. As part of the investigation and evaluation of corrosion behavior for these materials two types of test methods are used i.e. longer corrosion tests such as: autoclaving at high temperature and pressure in different chemical media-specific patterns in NPP and accelerated methods like: electrochemical techniques, accelerated chemical tests, etc. This paper presents some methods of analysis for materials corrosion; methods of assessment of corrosion of structural materials exposed to specific operating conditions and environment in NPPs. The electrochemical measurements show the following advantages: a) Allowing a direct method to accelerate the corrosion processes without altering the environment, b) It can be used as an nondestructive tool for assessing the rate of corrosion and c) Offers the possibility of conducting such investigations in - situ and ex- situ. Corroborating the environmental chemistry that was born on samples movies investigation results obtained by the methods above, it is possible to identify the types of corrosion of the materials and sometimes even those processes and mechanisms of corrosion. (authors)

A Study on the Organizational Components Affecting the Communication-Related Events in Nuclear Power Plant

International Nuclear Information System (INIS)

Lee, Seung Min; Jang, In Seok; Seong, Poong Hyun

2009-01-01

It is important to communicate clearly and effectively in order to achieve and improve team performance, also in the view point of safety, in nuclear power plant (NPP). Researchers have studied on lots of accidents and incidents related to communication and analyzed the elements affecting communication fail in the side of sender-receiver communication process so that they have found which process was failed to communicate each other. But we cannot disregard on human cognition, level of understanding, and individual or team characteristic on the communication process, so we need to analyze the elements of communication-related events in the side of human and team components that we will find why operators could not avoid failing their communication. In this paper we enumerate key organizational components, collect events related to communication in NPP and count the total number of components affecting communication fail. Finally we perform the pairwise-comparison using those values and understand major factors affecting communication-related events

Natural versus artificial aging of nuclear power plant components

International Nuclear Information System (INIS)

Shaw, M.T.

1992-01-01

This program seeks to understand the aging of polymeric materials, in cables and other components in nuclear reactor containment, by comparing aging processes for a variety of materials under natural conditions with those under the accelerated laboratory conditions used in qualification. The first five-year phase has been completed in what is planned as a long-term study of up to 40 years. Data from the program can be used as a basis of forecasting more realistic lifetimes in reactor service. The program is of critical importance for utilities both for the safe operation of plants and for minimizing the cost of periodic replacements upon expiration of originally predicted qualified life. The first five-year period has involved the selection and acquisition of test specimens, their preparation for placement in the containment, the selection of plants and locations for the specimens, the establishment of methods for monitoring radiation and temperature levels at each site, development of plans for scheduled removals, test method development, and testing of the specimens by physical and mechanical methods. Specimens have been subjected to short-term accelerated aging, as well as to reactor containment aging for up to five years. They consist of many types of polymers in products of several different manufacturers. Environmental conditions cover a wide range of temperature and radiation levels at 17 locations in 9 reactors of participating utilities. Initial results, which include tests of special cases subject to 8 years of reactor aging at Northeast Utilities, indicate several instances of changes having statistical significance in density or tensile properties due to containment service, but none of these changes are large enough to be of any concern. 12 refs., 19 figs., 21 tabs

Detection and Sizing of Defects in Structural Components of a Nuclear Power Plant by ECT

International Nuclear Information System (INIS)

Chen Zhenmao; Miya, Kenzo

2005-01-01

In this paper, progress of ECT technique for inspection of stress corrosion cracks in a structural component of a nuclear power plant is reported. Access and scanning vehicle (robot), advanced probes for SG tube inspection, development and evaluation of new probes for welding joint, and ECT based crack sizing technique are described respectively. Based on these new techniques, it is clarified that ECT can play as a supplement of UT for the welding zone inspection. It is also proved in this work that new ECT sensors are efficient even for a stainless plate as thick as 15mm

Cost benefit justification of nuclear plant reliability improvement

International Nuclear Information System (INIS)

El-Sayed, M.A.H.; Abdelmonem, N.M.

1985-01-01

The design of the secondary steam loop of the nuclear power plant has a significant effect on the reliability of the plant. Moreover, the necessity to cool a reactor safely has increased the reliability demanded from the system. The rapidly rising construction costs and fuel prices in recent years have stimulated a great deal in optimizing the productivity of a nuclear power plant through reliability improvement of the secondary steamloop and the reactor cooling system. A method for evaluating the reliability of steam loop and cooling system of a nuclear power plant is presented. The method utilizes the cut-set technique. The developed method can be easily used to show to what extent the overall reliability of the nuclear plant is affected by the possible failures in the steam and cooling subsystem. A model for calculating the increase in the nuclear plant productivity resulting from a proposed improvement in the two subsystems reliability is discussed. The model takes into account the capital cost of spare parts for several components, replacement energy, operating and maintenance costs

Feasibility of risk-informed technology for japanese nuclear power plants

International Nuclear Information System (INIS)

Yoshida, Tomoo; Fujioka, Terutaka; Kirimoto, Yorihiro; Ueda, Nobuyuki; Kinoshita, Izumi; Kashima, Koichi

2000-01-01

Risk-informed technology utilizes Probabilistic Safety Assessment for streamlining the maintenance of nuclear power plants. With this technology, plant components are categorized as either high or low-safety-significant components. The Maintenance requirements focuses on high safety-significant components and are relieved for low safety significant ones. This is expected to reduce plant cost while maintaining safety. We investigated especially risk-informed inservice inspection of piping in U.S. nuclear power plants in the interest of determining its feasibility for Japanese plants. Quantitative and qualitative RI-ISI methods were developed by the ASME/Westinghouse Owners Group and EPRI, respectively. These methods have been incorporated in the ASME Section 11 Code Cases and endorsed by the U.S. Nuclear Regulatory Commission. The quantitative method evaluates component segment risks in terms of pipe failure probability calculated with a probabilistic fracture mechanics(PFM) model and pipe failure impact categorization on core damage frequency(CDF) calculated with PSA. The qualitative method uses pipe failure potential categorization derived from the plant service experiences and pipe failure impact on CDF derived from the PSA insight. The PFM model is applicable only to failures from initial welding defects and stress corrosion cracking, therefore it does not cover such significant failure mechanisms found in nuclear power plants as corrosion or high-cycle fatigue, etc.. Thus, a qualitative failure potential categorization method was developed on the basis of the service experiences of the U.S. nuclear power plants, so that appropriate categorization rules must be developed on the service experiences in Japanese plants. Accordingly, we have devised a software framework with a computer-aided system for the selection of risk significant elements. This system consists of a piping failure database module, a piping failure analysis module, and a piping failure potential

Cooperation of nuclear, thermal and hydroelectric power plants in the power system

International Nuclear Information System (INIS)

1984-01-01

The conference heard 36 papers of which 23 were incorporated in INIS. The subjects discussed were: the development of power industry in Czechoslovakia, methods of statistical analysis of data regarding nuclear power plant operation, the incorporation of WWER nuclear power plants in the power supply system, the standardization of nuclear power plants, the service life of components, use of nuclear energy sources, performance of the reactor accident protection system, the use of nuclear power and heating plants in Hungary, risk analysis, optimization of nuclear power plants, accidents caused by leakage of the primary and secondary circuit. (J.P.)

Nuclear Power Plant Control and Instrumentation activities in Finland

International Nuclear Information System (INIS)

Haapanen, P.; Wahlstroem, B.

1990-01-01

Finland has achieved some remarkable achievements in nuclear power production. Existing four plants have some of the best operating records in the world - high capacity factors, low occupational doses and short refuelling outages. Although public opinion was strongly turned against nuclear power after Chernobyl accident, and no decisions for new nuclear plants can be made before next elections in 1991, the nuclear option is still open. Utility companies are maintaining readiness to start new construction immediately after a positive political decision is made. One important component of the good operation history of the Finnish nuclear power plants is connected to the continuous research, development, modification and upgrading work, which is proceeding in Finland. In the following a short description is given on recent activities related to the I and C-systems of the nuclear power plants. (author). 2 tabs

Major plant retrofits at Monticello nuclear generating plant

International Nuclear Information System (INIS)

Larsen, D.E.; Hogg, C.B.

1986-01-01

For the past several years, Northern States Power (NSP) has been making major plant retrofits to Monticello Nuclear generating Station in order to improve plant availability and upgrade the plant components for the potential extension of the operating license (life extension). This paper discusses in detail three major retrofits that have been completed or in the process of completion; recirculation loop piping replacement, reactor pressure vessel (RPV) water level-instrumentation modification, core spray piping replacement, the authors will address the scope of work, design and installation concerns, and life extension considerations during the design and procurement process for these three projects

Code on the safety of nuclear power plants: Design

International Nuclear Information System (INIS)

1988-01-01

This Code is a compilation of nuclear safety principles aimed at defining the essential requirements necessary to ensure nuclear safety. These requirements are applicable to structures, systems and components, and procedures important to safety in nuclear power plants embodying thermal neutron reactors, with emphasis on what safety requirements shall be met rather than on specifying how these requirements can be met. It forms part of the Agency's programme for establishing Codes and Safety Guides relating to land based stationary thermal neutron power plants. The document should be used by organizations designing, manufacturing, constructing and operating nuclear power plants as well as by regulatory bodies

Monitoring ageing of components in nuclear plants

International Nuclear Information System (INIS)

Fritz, M.R.

1992-01-01

There are several mechanisms of ageing or damage in nuclear components, of which the best known can be classified into three categories: generalized damage mechanisms (wear, corrosion, erosion,...), local damage phenomena (fatigue, corrosion,...) and material property degradations. For ageing evaluation, the first requirement is a good understanding of the damage mechanisms and the determination of the kinetic laws and major influencing factors. When these factors are measurable physical parameters, ageing monitoring and periodic evaluation of damage level become possible. From the set of tools available for ageing evaluation, four are presented here in more detail: the transient logging procedure, the defect injuriousness analysis, the fatigue meter, the probabilistic approach to structural integrity. (author)

Monitoring ageing of components in nuclear plants

Energy Technology Data Exchange (ETDEWEB)

Fritz, M R [FRAMATOME, Paris (France)

1992-07-01

There are several mechanisms of ageing or damage in nuclear components, of which the best known can be classified into three categories: generalized damage mechanisms (wear, corrosion, erosion,...), local damage phenomena (fatigue, corrosion,...) and material property degradations. For ageing evaluation, the first requirement is a good understanding of the damage mechanisms and the determination of the kinetic laws and major influencing factors. When these factors are measurable physical parameters, ageing monitoring and periodic evaluation of damage level become possible. From the set of tools available for ageing evaluation, four are presented here in more detail: the transient logging procedure, the defect injuriousness analysis, the fatigue meter, the probabilistic approach to structural integrity. (author)

Nuclebras' installations for performance tests of nuclear power plants components

International Nuclear Information System (INIS)

Vasconcelos Paiva, I.P. de; Avelar Esteves, F. de; Horta, J.A.L.; Resende, M.F.R.; Pinheiro, R.B.

1984-01-01

The reasons for Nuclebras' Nuclear Technology Development Center to implement a laboratory for supporting Brazilian manufactures, giving to them the means for performing functional tests of industrial products, are presented. A brief description of facilities under construction: the components Test Loop and Facility for Testing N.P.P. components under Accident conditions, and other already in operation, as well as its objectives and main technical characteristics. Some test results had already obtained are also presented. (Author) [pt

Coupling technology for dual-purpose nuclear-desalting plants

International Nuclear Information System (INIS)

Jones, J.E. Jr.; Anderson, T.D.; Reed, S.A.

1976-11-01

Although the basic technology for the various components of nuclear dual-purpose plants is reasonably well developed, the techniques of coupling the elements together to form a reliable, economical system that will satisfy the diverse operating requirements are not well established. The purpose of the study reported is to examine the technical, economic, and safety considerations in coupling nuclear power plants with distillation units to form a dual-purpose power and water distillation plant. The basic coupling arrangement required to provide a large-scale dual-purpose water plant is to supply steam to the water plant from the exhaust of a back-pressure turbine. The principal component at the interface that may require major research and development is the back-pressure turbine. To satisfy the operational requirements, two major auxiliary systems will be needed. These are: (1) a prime-steam bypass system, and (2) auxiliary condensers. These systems will provide a degree of independence between water and power production and can be justified economically

Seismic analysis of nuclear power plants

International Nuclear Information System (INIS)

Halbritter, A.L.

1984-01-01

Nuclear Power Plants require exceptional safety guarantees which are reflected in a rigorous control of the employed materials, advanced construction technology, sophisticated methods of analysis and consideration of non conventional load cases such as the earthquake loading. In this paper, the current procedures used in the seismic analysis of Nuclear Power Plants are presented. The seismic analysis of the structures has two objectives: the determination of forces in the structure in order to design it against earthquakes and the generation of floor response spectra to be used in the design of mechanical and electrical components and piping systems. (Author) [pt

Health protection and industrial safety. Nuclear power plants

International Nuclear Information System (INIS)

1987-03-01

The standard applies to components of the primary circuit including its auxiliary facilities, and of the secondary circuit of nuclear power plants with pressurized water reactors; to lifting gear and load take-ups for the transport of nuclear fuel and primary circuit components; to elevators within the containment, electrical installations, and piping and valves of radiation protection monitoring equipment. Part 1 defines the terms and specifies engineered safety requirements

Nuclear plant-aging research on reactor protection systems

International Nuclear Information System (INIS)

Meyer, L.C.

1988-01-01

This report presents the rsults of a review of the Reactor Trip System (RTS) and the Engineered Safety Feature Actuating System (ESFAS) operating experiences reported in Licensee Event Reports (LER)s, the Nuclear Power Experience data base, Nuclear Plant Reliability Data System, and plant maintenance records. Our purpose is to evaluate the potential significance of aging, including cycling, trips, and testing as contributors to degradation of the RTS and ESFAS. Tables are presented that show the percentage of events for RTS and ESFAS classified by cause, components, and subcomponents for each of the Nuclear Steam Supply System vendors. A representative Babcock and Wilcox plant was selected for detailed study. The US Nuclear Regulatory Commission's Nuclear Plant Aging Research guidelines were followed in performing the detailed study that identified materials susceptible to aging, stressors, environmental factors, and failure modes for the RTS and ESFAS as generic instrumentation and control systems. Functional indicators of degradation are listed, testing requirements evaluated, and regulatory issues discussed

Study of wet blasting of components in nuclear power stations

International Nuclear Information System (INIS)

Hall, J.

1999-12-01

This report looks at the method of wet blasting radioactive components in nuclear power stations. The wet blaster uses pearl shaped glass beads with the dimensions of 150-250 μm mixed with water as blasting media. The improved design, providing outer operator's positions with proper radiation protection and more efficient blasting equipment has resulted in a lesser dose taken by the operators. The main reason to decontaminate components in nuclear power plants is to enable service on these components. On components like valves, pump shafts, pipes etc. oxides form and bind radiation. These components are normally situated at some distance from the reactor core and will mainly suffer from radiation from so called activation products. When a component is to be decontaminated it can be decontaminated to a radioactive level where it will be declassified. This report has found levels ranging from 150-1000 Bq/kg allowing declassification of radioactive materials. This difference is found between different countries and different organisations. The report also looks at the levels of waste generated using wet blasting. This is done by tracking the contamination to determine where it collects. It is either collected in the water treatment plant or collected in the blasting media. At Barsebaeck the waste levels, from de-contaminating nearly 800 components in one year, results in a waste volume of about 0,250 m 3 . This waste consists of low and medium level waste and will cost about 3 600 EURO to store. The conclusions of the report are that wet blasting is an indispensable way to treat contaminated components in modern nuclear power plants. The wet blasting equipment can be improved by using a robot enabling the operators to remotely treat components from the outer operator's positions. There they will benefit from better radiation protection thus further reduce their taken dose. The wet blasting equipment could also be used to better control the levels of radioactivity on

Study of wet blasting of components in nuclear power stations

Energy Technology Data Exchange (ETDEWEB)

Hall, J

1999-12-01

This report looks at the method of wet blasting radioactive components in nuclear power stations. The wet blaster uses pearl shaped glass beads with the dimensions of 150-250 {mu}m mixed with water as blasting media. The improved design, providing outer operator's positions with proper radiation protection and more efficient blasting equipment has resulted in a lesser dose taken by the operators. The main reason to decontaminate components in nuclear power plants is to enable service on these components. On components like valves, pump shafts, pipes etc. oxides form and bind radiation. These components are normally situated at some distance from the reactor core and will mainly suffer from radiation from so called activation products. When a component is to be decontaminated it can be decontaminated to a radioactive level where it will be declassified. This report has found levels ranging from 150-1000 Bq/kg allowing declassification of radioactive materials.This difference is found between different countries and different organisations. The report also looks at the levels of waste generated using wet blasting. This is done by tracking the contamination to determine where it collects. It is either collected in the water treatment plant or collected in the blasting media. At Barsebaeck the waste levels, from de-contaminating nearly 800 components in one year, results in a waste volume of about 0,250 m{sup 3}. This waste consists of low and medium level waste and will cost about 3 600 EURO to store. The conclusions of the report are that wet blasting is an indispensable way to treat contaminated components in modern nuclear power plants. The wet blasting equipment can be improved by using a robot enabling the operators to remotely treat components from the outer operator's positions. There they will benefit from better radiation protection thus further reduce their taken dose. The wet blasting equipment could also be used to better control the levels of

AP1000 plant construction in China: Ansaldo Nucleare contribution

International Nuclear Information System (INIS)

Frogheri, Monica; Saiu, Gianfranco

2009-01-01

On 24th of July 2007 Westinghouse Electric Co. signed landmark contracts with China's State Nuclear Power Technology Corporation (SNPTC), to provide four AP1000 nuclear power plants in China. The AP1000 is a two-loop 1117 MWe Pressurized Water Reactor (PWR). It is based on proven technology, but with an emphasis on safety features that rely on natural driving forces, such as pressurized gas, gravity flow, natural circulation flow and convection. Ansaldo Nucleare has provided a significant support to the passive plant technology development and, starting from 2000, is cooperating with Westinghouse to development of the AP1000 Plant. In the frame of the AP1000 Chinese agreement, Ansaldo Nucleare, in Joint Venture with Mangiarotti Nuclear, has signed a contract with Westinghouse for the design and the supply of innovative components to be installed in the first AP1000 unit to be constructed at the Sanmen site. The contract includes: the design of the steel containment vessel, preparation of construction and fabrication, specifications, design and supply of SCV mechanical penetrations, air locks and equipment hatches. Moreover, Ansaldo Nucleare is in charge of the final design of the AP1000 PRHR-HX and together with Mangiarotti Nuclear will supply the component for the Sanmen Unit 1 NPP. The paper presents an overview of the design and manufacturing activities performed by Ansaldo Nucleare and its partners for the AP1000 plant in China. (authors)

PWR reactors for BBR nuclear power plants

International Nuclear Information System (INIS)

Structure and functioning of the nuclear steam generator system developed by BBR and its components are described. Auxiliary systems, control and load following behaviour and fuel management are discussed and the main data of PWR given. The brochure closes with a perspective of the future of the Muelheim-Kaerlich nuclear power plant. (GL) [de

Detection and sizing of defects in structural components of a nuclear power plant by ECT

International Nuclear Information System (INIS)

Chen, Z.; Miya, K.

2004-01-01

In this paper, progress of ECT (eddy current testing) technique for inspection of stress corrosion cracks in a structural component of a nuclear power plant is reported. Access and scanning vehicle (robot), advanced probes for steam generator tube inspection, development and evaluation of new probes for welding joint, and ECT based crack sizing technique are described respectively. Based on these new techniques, it is clarified that ECT can play as a supplement of ultrasonic techniques for the welding zone inspection. It is also proved in this work that new ECT sensors are efficient even for a stainless plate as thick as 15 mm. (authors)

RATU - Nuclear power plant structural safety research programme

International Nuclear Information System (INIS)

Rintamaa, R.

1992-07-01

Studies on the structural materials in nuclear power plants create the experimental data and background information necessary for the structural integrity assessments of mechanical components. The research is carried out by developing experimental fracture mechanics methods including statistical analysis methods of materials property data, and by studying material ageing and, in particular, mechanisms of material deterioration due to neutron irradiation, corrosion and water chemistry. Besides material studies, new testing methods and sensors for measurement of loading and water chemistry parameters have been developed. The monitoring data obtained in real power plants has been used to simulate more precisely the real environment during laboratory tests. The research on structural analysis has focused on extending and verifying the analysis capabilities for structural assessments of nuclear power plants. A widely applicable system including various computational fracture assessment methods has been created with which different structural problems can be solved reliably and effectively. Research on reliability assessment of maintenance in nuclear power plants is directed to practical case studies on components and structures of safety importance, and to the development of models for maintenance related decision support. A systematic analysis of motor-operated valve has been performed

Nuclear power plants

International Nuclear Information System (INIS)

Margulova, T.Ch.

1976-01-01

The textbook focuses on the technology and the operating characteristics of nuclear power plants equiped with pressurized water or boiling water reactors, which are in operation all over the world at present. The following topics are dealt with in relation to the complete plant and to economics: distribution and consumption of electric and thermal energy, types and equipment of nuclear power plants, chemical processes and material balance, economical characteristics concerning heat and energy, regenerative preheating of feed water, degassing and condenser systems, water supply, evaporators, district heating systems, steam generating systems and turbines, coolant loops and pipes, plant siting, ventilation and decontamination systems, reactor operation and management, heat transfer including its calculation, design of reactor buildings, and nuclear power plants with gas or sodium cooled reactors. Numerous technical data of modern Soviet nuclear power plants are included. The book is of interest to graduate and post-graduate students in the field of nuclear engineering as well as to nuclear engineers

A survival analysis on critical components of nuclear power plants

International Nuclear Information System (INIS)

Durbec, V.; Pitner, P.; Riffard, T.

1995-06-01

Some tubes of heat exchangers of nuclear power plants may be affected by Primary Water Stress Corrosion Cracking (PWSCC) in highly stressed areas. These defects can shorten the lifetime of the component and lead to its replacement. In order to reduce the risk of cracking, a preventive remedial operation called shot peening was applied on the French reactors between 1985 and 1988. To assess and investigate the effects of shot peening, a statistical analysis was carried on the tube degradation results obtained from in service inspection that are regularly conducted using non destructive tests. The statistical method used is based on the Cox proportional hazards model, a powerful tool in the analysis of survival data, implemented in PROC PHRED recently available in SAS/STAT. This technique has a number of major advantages including the ability to deal with censored failure times data and with the complication of time-dependant co-variables. The paper focus on the modelling and a presentation of the results given by SAS. They provide estimate of how the relative risk of degradation changes after peening and indicate for which values of the prognostic factors analyzed the treatment is likely to be most beneficial. (authors). 2 refs., 3 figs., 6 tabs

Test to prove the resistance to incidents of components of electric and control systems in the safety containment of nuclear power plants

International Nuclear Information System (INIS)

1982-01-01

The marginal program for proving the suitability of safety-relevant components of electric and control systems in the safety containment during a loss-of-coolant incident is described. Variant test conditions are established in the component-specific test program. Special attention has been paid to the representation of the course of pressure and temperature for the performance test of the valve room of the Nuclear Power Plant Philippsburg 2. (DG) [de

Fracture mechanics and fatigue evaluation of nuclear reactor components

International Nuclear Information System (INIS)

Mattar Neto, Miguel; Andrade, Arnaldo H.P. de; Maneschy, Eduardo

1995-01-01

This paper presents a theoretical study available in the available literature for evaluation the environmental effects on the lifetime of nuclear power plant components. The author's motivation is to provide some technical tools to identify what research development could be done in this area

Current status and future prospects of Korean standardized nuclear power plant design

International Nuclear Information System (INIS)

Rieh, C.-H.; Park, S.-K.; Lee, B.-R.

1992-01-01

The authors reviewed a brief history of Korean nuclear industry since the first Kori-1 plant operation in 1978 with special emphasis on the NSSS and BOP design and engineering, and the design approaches for nuclear power plants in the future. Continued effort to enhance plant economy and operational safety has been made by increasing plant size, and improving safety features, systems and component reliability in various design aspects. Korean nuclear industry is now trying to be one of the major contributors to the world nuclear field in sharing nuclear technology gained from past experience and developed through internation technical cooperation programs

Final environmental impact statement for the continued operation of the Pantex Plant and associated storage of nuclear weapon components. Volume 3 -- Comment response

International Nuclear Information System (INIS)

1996-11-01

The Draft Environmental Impact Statement (EIS) for the continued operation of Pantex Plant was published in March 1996. The document assessed the alternatives of no action, relocation of the storage of plutonium components resulting from nuclear weapon disassemble activities at Pantex Plant to another site, and the proposed action (preferred alternative) of continuing operations and increasing the quantity of pits in interim storage at Pantex Plant. This report contains the comments and responses received on the Draft EIS

Safety of nuclear power plants: Design. Safety requirements

International Nuclear Information System (INIS)

2000-01-01

The present publication supersedes the Code on the Safety of Nuclear Power Plants: Design (Safety Series No. 50-C-D (Rev. 1), issued in 1988). It takes account of developments relating to the safety of nuclear power plants since the Code on Design was last revised. These developments include the issuing of the Safety Fundamentals publication, The Safety of Nuclear Installations, and the present revision of various safety standards and other publications relating to safety. Requirements for nuclear safety are intended to ensure adequate protection of site personnel, the public and the environment from the effects of ionizing radiation arising from nuclear power plants. It is recognized that technology and scientific knowledge advance, and nuclear safety and what is considered adequate protection are not static entities. Safety requirements change with these developments and this publication reflects the present consensus. This Safety Requirements publication takes account of the developments in safety requirements by, for example, including the consideration of severe accidents in the design process. Other topics that have been given more detailed attention include management of safety, design management, plant ageing and wearing out effects, computer based safety systems, external and internal hazards, human factors, feedback of operational experience, and safety assessment and verification. This publication establishes safety requirements that define the elements necessary to ensure nuclear safety. These requirements are applicable to safety functions and the associated structures, systems and components, as well as to procedures important to safety in nuclear power plants. It is expected that this publication will be used primarily for land based stationary nuclear power plants with water cooled reactors designed for electricity generation or for other heat production applications (such as district heating or desalination). It is recognized that in the case of

Safety of nuclear power plants: Design. Safety requirements

International Nuclear Information System (INIS)

2004-01-01

The present publication supersedes the Code on the Safety of Nuclear Power Plants: Design (Safety Series No. 50-C-D (Rev. 1), issued in 1988). It takes account of developments relating to the safety of nuclear power plants since the Code on Design was last revised. These developments include the issuing of the Safety Fundamentals publication, The Safety of Nuclear Installations, and the present revision of various safety standards and other publications relating to safety. Requirements for nuclear safety are intended to ensure adequate protection of site personnel, the public and the environment from the effects of ionizing radiation arising from nuclear power plants. It is recognized that technology and scientific knowledge advance, and nuclear safety and what is considered adequate protection are not static entities. Safety requirements change with these developments and this publication reflects the present consensus. This Safety Requirements publication takes account of the developments in safety requirements by, for example, including the consideration of severe accidents in the design process. Other topics that have been given more detailed attention include management of safety, design management, plant ageing and wearing out effects, computer based safety systems, external and internal hazards, human factors, feedback of operational experience, and safety assessment and verification. This publication establishes safety requirements that define the elements necessary to ensure nuclear safety. These requirements are applicable to safety functions and the associated structures, systems and components, as well as to procedures important to safety in nuclear power plants. It is expected that this publication will be used primarily for land based stationary nuclear power plants with water cooled reactors designed for electricity generation or for other heat production applications (such as district heating or desalination). It is recognized that in the case of

Modernization of turbines in nuclear power plants

International Nuclear Information System (INIS)

Harig, T.

2005-01-01

An ongoing goal in the power generation industry is to maximize the output of currently installed assets. This is most important at nuclear power plants due to the large capital investments that went into these plants and their base loaded service demands. Recent trends in the United States show a majority of nuclear plants are either obtaining, or are in the process of obtaining NRC approvals for operating license extensions and power uprates. This trend is evident in other countries as well. For example, all Swedish nuclear power plants are currently working on projects to extend their service life and maximize capacity through thermal uprate and turbine-generator upgrade with newest technology. The replacement of key components with improved ones is a means of optimizing the service life and availability of power plants. Economic advantages result from increased efficiency, higher output, shorter startup and shutdown times as well as reduced outage times and service costs. The rapid advances over recent years in the development of calculation programs enables adaptation of the latest blading technology to the special requirements imposed by steam turbine upgrading. This results in significant potential for generating additional output with the implementation of new technology, even without increased thermal power. In contrast to maintenance and investment in pure replacement or repair of a component with the primary goal of maintaining operability and reliability, the additional output gained by upgrading enables a return on investment to be reaped. (orig.)

Storage, handling and movement of fuel and related components at nuclear power plants

International Nuclear Information System (INIS)

1979-01-01

The report describes in general terms the various operations involved in the handling of fresh fuel, irradiated fuel, and core components such as control rods, neutron sources, burnable poisons and removable instruments. It outlines the principal safety problems in these operations and provides the broad safety criteria which must be observed in the design, operation and maintenance of equipment and facilities for handling, transferring, and storing nuclear fuel and core components at nuclear power reactor sites

Method for treatment of wastewater of nuclear power plants

International Nuclear Information System (INIS)

Ito, Kazutoshi; Suzuki, Katsumi; Suzuki, Mamoru; Minato, Akira.

1984-01-01

A method for treatment of wastewater of nuclear power plants is characterized by the fact that concentration and volume reduction are performed after Ca and Mg as components for the formation of an adhering scale is converted to an 8-oxyquinoline complex, which is hardly soluble in water, and does not precipitate out as an adhering scale, by the addition of 8-oxyquinoline into nuclear power plant wastewater

Nuclear power plant maintenance optimisation SENUF network activity

International Nuclear Information System (INIS)

Ahlstrand, R.; Bieth, M.; Pla, P.; Rieg, C.; Trampus, P.

2004-01-01

During providing scientific and technical support to TACIS and PHARE nuclear safety programs a large amount of knowledge related to Russian design reactor systems has accumulated and led to creation of a new Network concerning Nuclear Safety in Central and Eastern Europe called ''Safety of Eastern European type Nuclear Facilities'' (SENUF). SENUF contributes to bring together all stakeholders of TACIS and PHARE: beneficiaries, end users, Eastern und Western nuclear industries, and thus, to favour fruitful technical exchanges and feedback of experience. At present the main focus of SENUF is the nuclear power plant maintenance as substantial element of plant operational safety as well as life management. A Working Group has been established on plant maintenance. One of its major tasks in 2004 is to prepare a status report on advanced strategies to optimise maintenance. Optimisation projects have an interface with the plant's overall life management program. Today, almost all plants involved in SENUF network have an explicit policy to extend their service life, thus, component ageing management, modernization and refurbishment actions became much more important. A database is also under development, which intends to help sharing the available knowledge and specific equipment and tools. (orig.)

Glossary of nuclear power plant ageing

International Nuclear Information System (INIS)

1999-01-01

A glossary is presented of the terminology for understanding and managing the ageing of nuclear power plant systems, structures and components. This glossary has been published by NEA, in cooperation with CEC and IAEA, as a handy reference to facilitate and encourage use of common ageing terminology. The main benefits are improved reporting and interpretation of plant data on SSC degradation and failure, and improved interpretation and compliance with codes, regulations and standards related to nuclear plant ageing. The goal is to provide plant personnel with a common set of terms that have uniform, industry-wide meanings, and to facilitate discussion between experts from different countries. The glossary is in five languages: English, French, German, Spanish and Russian. In each language section terms are listed alphabetically, with sequential members which are repeated in the English section thus allowing cross-reference between al languages. (R.P.)

Application of fatigue monitoring system in PWR nuclear power plant

International Nuclear Information System (INIS)

Piao Lei

2014-01-01

Fatigue failure is one form of equipment failure of nuclear power plant, influencing equipment lifetime and lifetime extension. Fatigue monitoring system can track real thermal transient at fatigue sensitive components, establish a basis for fatigue analyses based on realistic operating loads, identify unexpected operational transients, optimize the plant behavior by improved operating modes, provide supporting data for lifetime management, enhance security of plant and reduce economical loss. Fatigue monitoring system has been applied in many plants and is required to be applied in Generation-III nuclear power plant. It is necessary to develop the fatigue monitoring system with independent intellectual property rights and improve the competitiveness of domestic Generation-III nuclear power technology. (author)

Operational characteristics of nuclear power plants - modelling of operational safety

International Nuclear Information System (INIS)

Studovic, M.

1984-01-01

By operational experience of nuclear power plants and realize dlevel of availability of plant, systems and componenst reliabiliuty, operational safety and public protection, as a source on nature of distrurbances in power plant systems and lessons drawn by the TMI-2, in th epaper are discussed: examination of design safety for ultimate ensuring of safe operational conditions of the nuclear power plant; significance of the adequate action for keeping proess parameters in prescribed limits and reactor cooling rquirements; developed systems for measurements detection and monitoring all critical parameters in the nuclear steam supply system; contents of theoretical investigation and mathematical modeling of the physical phenomena and process in nuclear power plant system and components as software, supporting for ensuring of operational safety and new access in staff education process; program and progress of the investigation of some physical phenomena and mathematical modeling of nuclear plant transients, prepared at faculty of mechanical Engineering in Belgrade. (author)

Some power uprate issues in nuclear power plants

International Nuclear Information System (INIS)

Tipping, Philip

2008-01-01

Issues and themes concerned with nuclear power plant uprating are examined. Attention is brought to the fact that many candidate nuclear power plants for uprating have anyway been operated below their rated power for a significant part of their operating life. The key issues remain safety and reliability in operation at all times, irrespective of the nuclear power plant's chronological or design age or power rating. The effects of power uprates are discussed in terms of material aspects and expected demands on the systems, structures and components. The impact on operation and maintenance methods is indicated in terms of changes to the ageing surveillance programmes. Attention is brought to the necessity checking or revising operator actions after power up-rating has been implemented

Materials for Nuclear Plants From Safe Design to Residual Life Assessments

CERN Document Server

Hoffelner, Wolfgang

2013-01-01

The clamor for non-carbon dioxide emitting energy production has directly  impacted on the development of nuclear energy. As new nuclear plants are built, plans and designs are continually being developed to manage the range of challenging requirement and problems that nuclear plants face especially when managing the greatly increased operating temperatures, irradiation doses and extended design life spans. Materials for Nuclear Plants: From Safe Design to Residual Life Assessments  provides a comprehensive treatment of the structural materials for nuclear power plants with emphasis on advanced design concepts.   Materials for Nuclear Plants: From Safe Design to Residual Life Assessments approaches structural materials with a systemic approach. Important components and materials currently in use as well as those which can be considered in future designs are detailed, whilst the damage mechanisms responsible for plant ageing are discussed and explained. Methodologies for materials characterization, material...

Dynamic interaction of components, structure, and foundation of nuclear power facilities

International Nuclear Information System (INIS)

Pajuhesh, J.; Hadjian, A.H.

1977-01-01

A solution is formulated for the dynamic analysis of structures and components with different stiffness and damping characteristics, including the consideration of soil-structure interaction effects. Composite structures are often analysed approximately, in particular with regards to damping. For example, the reactor and other equipment in nuclear power plant structures are often analysed by assuming them uncoupled from the supporting structures. To achieve a better accuracy, the coupled system is hereby analysed as a composite component-structure-soil system. To demonstrate the assembly technique, two examples are considered: (a) a steel structure sitting on a concrete stem and linked by a steel bridge to another concrete structure, and (b) an actual model of a nuclear power plant containment structure. (Auth.)

A nuclear power plant status monitor

International Nuclear Information System (INIS)

Chu, B.B.; Conradi, L.L.; Weinzimmer, F.

1986-01-01

Power plant operation requires decisions that can affect both the availability of the plant and its compliance with operating guidelines. Taking equipment out of service may affect the ability of the plant to produce power at a certain power level and may also affect the status of the plant with regard to technical specifications. Keeping the plant at a high as possible production level and remaining in compliance with the limiting conditions for operation (LCOs) can dictate a variety of plant operation and maintenance actions and responses. Required actions and responses depend on the actual operational status of a nuclear plant and its attendant systems, trains, and components which is a dynamic situation. This paper discusses an Electric Power Research Institute (EPRI) Research Project, RP 2508, the objective of which is to combine the key features of plant information management systems with systems reliability analysis techniques in order to assist nuclear power plant personnel to perform their functions more efficiently and effectively. An overview of the EPRI Research Project is provided along with a detailed discussion of the design and operation of the PSM portion of the project

Studies on the effectiveness of measures to maintain the integrity of pressurized components in German nuclear power plants. Final report

International Nuclear Information System (INIS)

Elmas, M.; Jendrich, U.; Michel, F.; Reck, H.; Schimpfke, T.; Walter, M.; Wenke, R.

2013-03-01

The overall objective of the project was to investigate the effectiveness of measures to maintain the as-built quality of the pressure-retaining components in German nuclear power plants. In particular, investigations were performed on the application of the break preclusion concept, existing monitoring systems and the significance of the pressure test as part of the inspection concept. Moreover, the KompInt knowledge base has been updated. Break preclusion for pipes was applied in all German plants already during planning or after commissioning to a varying extent. The basic features of the required assessments were considered in the German nuclear regulations for the first time by inclusion in the safety requirements for nuclear power plants of 2012. The requirements for assessments, differing in their degree of detail, in the interpretations of these safety requirements and in the safety standard KTA 3206 are still in the draft stage. For the first time, the vessels as well as housings of valves and pumps are also included in the concept. Through the use of advanced monitoring systems it was possible in German plants at an early stage to establish modes of operation that minimise the load on components, to carry out appropriate technical backfitting measures, and to identify damages. In plant areas where local water chemistry parameters may result that deviate from the specification, the effectiveness of water chemistry monitoring is limited. In this case, other operational measures must be taken. The results of the simulations performed with the help of the GRS-developed PROST computer code to determine the significance of pressure tests lead - in accordance with the results of operating experience evaluation - to the conclusion that pressure tests carried out within the pressure-retaining boundary contribute to safeguarding the integrity. The user-friendliness of the KompInt knowledge base has been increased by changing over to a new hardware, a software

10 CFR Appendix S to Part 50 - Earthquake Engineering Criteria for Nuclear Power Plants

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Earthquake Engineering Criteria for Nuclear Power Plants S... FACILITIES Pt. 50, App. S Appendix S to Part 50—Earthquake Engineering Criteria for Nuclear Power Plants... nuclear power plant structures, systems, and components important to safety to withstand the effects of...

Directory of nuclear power plants in the world, 1985

International Nuclear Information System (INIS)

Fujii, Haruo

1985-01-01

This book presents technical information and estimates trends of load factors and construction costs of nuclear power plants. Particularly road maps indicating plants are drawn in, which would be practical in visiting them. The data used here are directly confirmed by operators in every part of the world. Therefore, they reflect up-to-date nuclear power developments and its future. This allows wide and exact understanding of world's nuclear power. Chapter 1 presents nuclear power growth around the world and estimates forecasts based on information from electric power companies: nuclear power growths and the growths in the number of reactors around the world, in WOCA (World outside the Centrally Planned Economies Area), in CPEA (Centrally Planned Economies Area) are analyzed in detail. Chapter 2 presents nuclear power plants on maps by country. The maps show exact locations of nuclear power plants with local cities around them, rivers and lakes. For convenience, symbols are given to aid in identifying the types of reactors. Chapter 3 presents general information of nuclear power plants. Also the addresses of operators, all segments of nuclear power supply industries and nuclear organizations are included. For convenience, the index of nuclear power plants is added. Chapter 4 presents technical information, road maps in large scales and photographs of nuclear power plants in the world. The road maps show exact locations of plants. Chapter 5 presents operating experiences, load factors, refuelling and maintenance outages. The trends of data are analyzed both regionally (WOCA, CPEA) and world-widely. Chapter 6 presents trends of construction costs, component costs as percent of total construction costs and direct costs, and construction durations. (J.P.N.)

Ageing management of nuclear power plant - the Tarapur experience

International Nuclear Information System (INIS)

Anilkumar, K.R.; Das, P.K.; Bhattacharjee, S.; Ramamurty, U.

2006-01-01

Tarapur Atomic Power Station, the longest serving Nuclear Power Plant in the Asian continent has completed 36 years of successful operation and generated more than 70,000 million units of electric power. Built in late sixties, with the state-of-the-art safety features prevailing then, TAPS through the process of evolution has become safer plant due to efforts of upgradation, renovation and refurbishment prompted by the station's operating experience, feed back from overseas reactors, lessons learnt from nuclear incidents, accidents and fresh review of design basis and safety analysis of the plant. All components of a Nuclear power plant experience some degradation with time. The Reactor Pressure Vessels (RPV) designed for 40 effective full power years (EFPY) of operation have operated for less than 20 EFPY and the material condition is assessed to be fit for some more years of service. The condition of the containment and main plant buildings was assessed to be satisfactory. The Ageing Management Programme (AMP) involved identification of key systems, structures and components (SSCs) that may experience degradation due to ageing, and take corrective measures through maintenance, repair and/or replacement. The identified components were classified as major critical components, important systems and other critical components. For each component mode of degradation was identified, ageing assessment was done and action plan was finalized. Replacement of some important equipment like 3 x 50 % capacity Emergency Diesel Generators (EDG) with 3 x 100 % capacity EDG, Salt Service Water (SSW) pumps, Control rod drive (CRD) pumps, Emergency Condenser tube bundles, Station battery has been done on the basis of condition monitoring and to obviate common cause failure and enhance the system reliability. Samples of Safety related cables were subjected to residual life assessment (RLA) and replacement action firmed up on the basis of the RLA findings. Condition survey of Main

Study on application of operating experience to new nuclear power plant

International Nuclear Information System (INIS)

Hong, Nam Pyo

1991-01-01

From the standpoint of designing the nuclear power plant, nine operating units have been designed and constructed as turn-key base by foreign Nuclear Steam Supply System (NSSS) Suppliers or as component base by foreign Architect/Engineer companies. In case of the component base project, the owner of electric company generally has merits that owner's operational experiences can be effectively incorporated from the beginning stage of design by A/E. Even though six nuclear units, Kori Units 3 and 4, Yonggwang Units 1 and 2, and Ulchin Units 1 and 2, were designed as component base by foreign A/E's, operational experience feedback from Kori Unit 1, such as design improvement and system upgrade, could not be reflected, because the design process of the following units started well ahead before Kori Unit 1 operating experience is obtained enough to reflect on future nuclear power plant design. It can be stated that foreign A/E's used their experience in designing nuclear projects on very limited basis

Manufacture of piping components for nuclear power plants

International Nuclear Information System (INIS)

Bartecek, R.

1983-01-01

Hammer forging of hollow forging ingots, extrusion and elestroslag remelting may be used for the manufacture of large pipes. Technologies have been developed for the manufacture of elbows based on various types of forming. These procedures mainly include the hydraulic pressing of elbows from tubes and the pressing of symmetrical halves of elbows with subsequent welding. The hammer forging of valves, cross pieces, etc., has been replaced by forging and pressing. In order to prevent failures from occurring in the pipes during operation of nuclear power plants, pipes are being made of larger forgings, which reduces the number of welds. This improves the quality of the pipes, reduces production and assembly costs and is metal-saving. (E.S.)

Indigenous procurement of nuclear components at Tarapur (Paper No. 013)

International Nuclear Information System (INIS)

Verma, D.K.; Moss, V.J.

1987-02-01

The Tarapur Atomic Power Station (TAPS) was the first nuclear power station in developing countries and the first twin BWR units in the world. The Station has two units of boiling water reactor of very early design; along with its turbo-generator and supporting systems; constructed by M/s. I.G.E. on turnkey basis. Based on vendor recommendations initial operating spares for 5 years of operation were purchased from original equipment manufacturers. This does not call for the participation of the ultimate user; in the design, development, manufacture and quality control and user's participation remained confined to assemble the acceptable component(s) procured from original source in the assembly. As early as 1972, Plant initiated indigenising the nuclear components by gradually increasing the contribution of indigenous industry with due participation of the departmental agencies. Procurement of nuclear components requires development of engineering to an extent; where interphase communication between TAPS and counterpart indigenous industry is practicable to motivate them. Feedback from operation and maintenance practices is also utilised effectively. For some of the components initial sample were developed at TAPS and subsequently bulk fabrication was taken by industry. This paper describes manufacture, quality control during the process of manufacture and procurement of indigenous nuclear components relevant to Tarapur Atomic Power Station. (author)

Specific safety aspects of the water-steam cycle important to nuclear power plant project

International Nuclear Information System (INIS)

Lobo, C.G.

1986-01-01

The water-steam cycle in a nuclear power plant is similar to that used in conventional power plants. Some systems and components are required for the safe nuclear power plant operation and therefore are designed according to the safety criteria, rules and regulations applied in nuclear installations. The aim of this report is to present the safety characteristics of the water-steam cycle of a nuclear power plant with pressurized water reactor, as applied for the design of the nuclear power plants Angra 2 and Angra 3. (Author) [pt

Application of 3-dimensional CAD modeling system in nuclear plants

International Nuclear Information System (INIS)

Suwa, Minoru; Saito, Shunji; Nobuhiro, Minoru

1990-01-01

Until now, the preliminary work for mutual components in nuclear plant were readied by using plastic models. Recently with the development of computer graphic techniques, we can display the components on the graphics terminal, better than with use of plastic model and actual plants. The computer model can be handled, both telescopically and microscopically. A computer technique called 3-dimensional CAD modeling system was used as the preliminary work and design system. Through application of this system, database for nuclear plants was completed in arrangement step. The data can be used for piping design, stress analysis, shop production, testing and site construction, in all steps. In addition, the data can be used for various planning works, even after starting operation of plant. This paper describes the outline of the 3-dimensional CAD modeling system. (author)

Technical specifications review of nuclear power plants: a risk-informed evaluation

International Nuclear Information System (INIS)

Saldanha, Pedro Luiz da Cruz; Sousa, Anna Leticia; Frutuoso e Melo, Paulo Fernando Ferreira; Duarte, Juliana Pacheco

2012-01-01

The use of risk information by a regulatory body as part of an integrated decision making process addresses the way in which risk information is being used as part of an integrated process in making decisions about safety issues at nuclear plants – commonly referred to as risk-informed decision making. The risk-informed approach aims to integrate in a systematic manner quantitative and qualitative, deterministic and probabilistic safety considerations to obtain a balanced decision. Probabilistic Safety Assessment (PSA) is a methodology that can be applied to provide a structured analysis process to evaluate the frequency and consequences of accidents scenarios in nuclear power plants. Technical Specifications (TS) are specifications regarding the characteristics of nuclear power plants (variables, systems or components) of overriding importance to nuclear safety and radiation protection, which is an integral part of plant operation authorization. Limiting Conditions of Operation (LCO) are the minimum levels of performance or capacity or operating system components required for the safe operation of nuclear plants, as defined in technical specifications. The Maintenance Rule (MR) is a requirement established by the U. S. Nuclear Regulatory Commission (NRC) to check the effectiveness of maintenance carried out in nuclear plants, and plant configuration control. The control of plant configuration is necessary to verify the impact of the maintenance of a safety device out of service on plant safety. The Electric Power Research Institute (EPRI) has assessed the role of probabilistic safety analysis in the regulation of nuclear power plants with the following objectives: a) to provide utilities with an approach for developing and implementing nuclear power station risk-managed technical specification programs; and b) to complement and supplement existing successful configuration risk management applications such as MR. This paper focuses on the evaluation of EPRI

Aging of concrete structures in nuclear power plants

International Nuclear Information System (INIS)

Naus, D.J.; Pland, C.B.; Arndt, E.G.

1991-01-01

The Structural Aging (SAG) Program, sponsored by the US Nuclear Regulatory Commission (USNRC) and conducted by the Oak Ridge National Laboratory (ORNL), had the overall objective of providing the USNRC with an improved basis for evaluating nuclear power plant structures for continued service. The program consists of three technical tasks: materials property data base, structural component assessment/repair technology, and quantitative methodology for continued service determinations. Major accomplishments under the SAG Program during the first two years of its planned five-year duration have included: development of a Structural Materials Information Center and formulation of a Structural Aging Assessment Methodology for Concrete Structures in Nuclear Power Plants. 9 refs

Westinghouse AP600 advanced nuclear plant design

International Nuclear Information System (INIS)

Gangloff, W.

1999-01-01

As part of the cooperative US Department of Energy (DOE) Advanced Light Water Reactor (ALWR) Program and the Electric Power Research Institute (EPRI), the Westinghouse AP600 team has developed a simplified, safe, and economic 600-megawatt plant to enter into a new era of nuclear power generation. Designed to satisfy the standards set by DOE and defined in the ALWR Utility Requirements Document (URD), the Westinghouse AP600 is an elegant combination of innovative safety systems that rely on dependable natural forces and proven technologies. The Westinghouse AP600 design simplifies plant systems and significant operation, inspections, maintenance, and quality assurance requirements by greatly reducing the amount of valves, pumps, piping, HVAC ducting, and other complex components. The AP600 safety systems are predominantly passive, depending on the reliable natural forces of gravity, circulation, convection, evaporation, and condensation, instead of AC power supplies and motor-driven components. The AP600 provides a high degree of public safety and licensing certainty. It draws upon 40 years of experience in light water reactor components and technology, so no demonstration plant is required. During the AP600 design program, a comprehensive test program was carried out to verify plant components, passive safety systems components, and containment behavior. When the test program was completed at the end of 1994, the AP600 became the most thoroughly tested advanced reactor design ever reviewed by the US Nuclear Regulatory Commission (NRC). The test results confirmed the exceptional behavior of the passive systems and have been instrumental in facilitating code validations. Westinghouse received Final Design Approval from the NRC in September 1998. (author)

The commissioning of nuclear power plants

International Nuclear Information System (INIS)

1989-09-01

The objectives and requirements to be met in commissioning nuclear power plants are presented. The objective of commissioning is to ensure that each component, subsystem, system, or structure in a plant will be capable of fulfilling its design requirements throughout its design life. The requirements for commissioning are: the preparation of a detailed, comprehensive, documented program to demonstrate that all components, systems and structures relevant to safety meet design intent; documented evidence that safety systems are fully operable and can meet design requirements; and, appropriate documentation of the actual state or behaviour of all components, systems and structures relevant to safety. All systems must be included in the commissioning program. Whenever possible, full safety system test should be performed. If a full system in situ test is not possible, alternative means are suggested. (8 refs.)

Current USAEC seismic requirements for nuclear power plants

International Nuclear Information System (INIS)

Mehta, D.S.

1975-01-01

The principal seismic and geologic considerations which guide the USAEC in its evaluation of the suitability of proposed sites for nuclear power plants and plant design bases are set forth as design criteria in the AEC regulatory guides. The basic requirements of seismic design and analysis for seismic Category I structures, components, and systems important to public safety have been established in the USAEC regulatory guides and Code of Federal Regulations. It is pointed out that the current state-of-art techniques, best available technology, and additional studies in the field of earthquake engineering can be utilized to resolve seismic concerns. The seismic design requirements for nuclear plants to withstand postulated earthquakes can be standardized and this will be a significant milestone in the continuation of the Nuclear Standardization Program. (author)

The licensing practice on nuclear power plants in Korea

International Nuclear Information System (INIS)

Moon, S. P.

1994-01-01

The evolution of Korean regulatory system has tightly coupled with development ot Korean nuclear power program. The nuclear power plant licensing has become a major regulatory function of the government when the construction of the Kori NPP Unit 1 started in early 1970s. During this period, domestic laws and regulations applicable to the licensing of NPP were not yet fully developed. Therefore the vendor countries' laws and regulations were applied as mandatory requirement. Beginning in the early 19808, component approach was used and contracts were awarded separately for major components of the plants, thus enabling more domestic industries to participate in the projects. The two-step licensing system was incorporated into the law. In the third phase from 1987, major efforts have been concentrated on the maximum participation of local industries. The overriding priority for selecting suppliers was the condition of higher nuclear technology transfer to Korea. The Korea Institute of Nuclear Safety (KINS) was established in 1990 as an independent regulatory expert organization

Survey of artificial intelligence methods for detection and identification of component faults in nuclear power plants

International Nuclear Information System (INIS)

Reifman, J.

1997-01-01

A comprehensive survey of computer-based systems that apply artificial intelligence methods to detect and identify component faults in nuclear power plants is presented. Classification criteria are established that categorize artificial intelligence diagnostic systems according to the types of computing approaches used (e.g., computing tools, computer languages, and shell and simulation programs), the types of methodologies employed (e.g., types of knowledge, reasoning and inference mechanisms, and diagnostic approach), and the scope of the system. The major issues of process diagnostics and computer-based diagnostic systems are identified and cross-correlated with the various categories used for classification. Ninety-five publications are reviewed

Structural health monitoring of power plant components based on a local temperature measurement concept

International Nuclear Information System (INIS)

Rudolph, Juergen; Bergholz, S.; Hilpert, R.; Jouan, B.; Goetz, A.

2012-01-01

The fatigue assessment of power plant components based on fatigue monitoring approaches is an essential part of the integrity concept and modern lifetime management. It is comparable to structural health monitoring approaches in other engineering fields. The methods of fatigue evaluation of nuclear power plant components based on realistic thermal load data measured on the plant are addressed. In this context the Fast Fatigue Evaluation (FFE) and Detailed Fatigue Calculation (DFC) of nuclear power plant components are parts of the three staged approach to lifetime assessment and lifetime management of the AREVA Fatigue Concept (AFC). The three stages Simplified Fatigue Estimation (SFE), Fast Fatigue Evaluation (FFE) and Detailed Fatigue Calculation (DFC) are characterized by increasing calculation effort and decreasing degree of conservatism. Their application is case dependent. The quality of the fatigue lifetime assessment essentially depends on one hand on the fatigue model assumptions and on the other hand on the load data as the basic input. In the case of nuclear power plant components thermal transient loading is most fatigue relevant. Usual global fatigue monitoring approaches rely on measured data from plant instrumentation. As an extension, the application of a local fatigue monitoring strategy (to be described in detail within the scope of this paper) paves the way of delivering continuously (nowadays at a frequency of 1 Hz) realistic load data at the fatigue relevant locations. Methods of qualified processing of these data are discussed in detail. Particularly, the processing of arbitrary operational load sequences and the derivation of representative model transients is discussed. This approach related to realistic load-time histories is principally applicable for all fatigue relevant components and ensures a realistic fatigue evaluation. (orig.)

Design of nuclear power plants

International Nuclear Information System (INIS)

Lobo, C.G.

1987-01-01

The criteria of design and safety, applied internationally to systems and components of PWR type reactors, are described. The main criteria of the design analysed are: thermohydraulic optimization; optimized arrangement of buildings and components; low costs of energy generation; high level of standardization; application of specific safety criteria for nuclear power plants. The safety criteria aim to: assure the safe reactor shutdown; remove the residual heat and; avoid the release of radioactive elements for environment. Some exemples of safety criteria are given for Angra-2 and Angra-3 reactors. (M.C.K.) [pt

Advanced nuclear plant control complex

International Nuclear Information System (INIS)

Scarola, K.; Jamison, S.; Manazir, R.M.; Rescorl, R.L.; Harmon, D.L.

1991-01-01

An advanced control room complex for a nuclear power plant, including a discrete indicator and alarm system which is nuclear qualified for rapid response to changes in plant parameters and a component control system which together provide a discrete monitoring and control capability at a panel in the control room. A separate data processing system, which need not be nuclear qualified, provides integrated and overview information to the control room and to each panel, through CRTs and a large, overhead integrated process status overview board. The discrete indicator and alarm system and the data processing system receive inputs from common plant sensors and validate the sensor outputs to arrive at a representative value of the parameter for use by the operator during both normal and accidental conditions, thereby avoiding the need for him to assimilate data from each sensor individually. The integrated process status board is at the apex of an information hierarchy that extends through four levels and provides access at each panel to the full display hierarchy. The control room panels are preferably of a modular construction, permitting the definition of inputs and outputs, the man machine interface, and the plant specific algorithms, to proceed in parallel with the fabrication of the panels, the installation of the equipment and the generic testing thereof. (author)

Aging management guideline for commercial nuclear power plants - tanks and pools

International Nuclear Information System (INIS)

Blocker, E.; Smith, S.; Philpot, L.; Conley, J.

1996-02-01

Continued operation of nuclear power plants for periods that extend beyond their original 40-year license period is a desirable option for many U.S. utilities. U.S. Nuclear Regulatory Commission (NRC) approval of operating license renewals is necessary before continued operation becomes a reality. Effective aging management for plant components is important to reliability and safety, regardless of current plant age or extended life expectations. However, the NRC requires that aging evaluations be performed and the effectiveness of aging management programs be demonstrated for components considered within the scope of license renewal before granting approval for operation beyond 40 years. Both the NRC and the utility want assurance that plant components will be highly reliable during both the current license term and throughout the extended operating period. In addition, effective aging management must be demonstrated to support Maintenance Rule (10 CFR 50.65) activities

Aging management guideline for commercial nuclear power plants - tanks and pools

Energy Technology Data Exchange (ETDEWEB)

Blocker, E.; Smith, S.; Philpot, L.; Conley, J.

1996-02-01

Continued operation of nuclear power plants for periods that extend beyond their original 40-year license period is a desirable option for many U.S. utilities. U.S. Nuclear Regulatory Commission (NRC) approval of operating license renewals is necessary before continued operation becomes a reality. Effective aging management for plant components is important to reliability and safety, regardless of current plant age or extended life expectations. However, the NRC requires that aging evaluations be performed and the effectiveness of aging management programs be demonstrated for components considered within the scope of license renewal before granting approval for operation beyond 40 years. Both the NRC and the utility want assurance that plant components will be highly reliable during both the current license term and throughout the extended operating period. In addition, effective aging management must be demonstrated to support Maintenance Rule (10 CFR 50.65) activities.

Understanding and managing corrosion in nuclear power plants

International Nuclear Information System (INIS)

Johnson, A.B. Jr.; Jarrell, D.B.; Sinha, U.P.; Shah, V.N.

1991-03-01

The main theme of this paper is a concept: understanding and managing corrosion in nuclear power plants. The concept is not new--in various forms the concept has been applied throughout the development and maturing of nuclear technology. However, the concept has frequently not been well conceived and applied. Too often, understanding corrosion has been based on reaction rather than on anticipation. Regulatory and utility industry initiatives are creating a climate and framework for more effective application of the concept. This paper characterizes the framework and provides some illustrations of how the concept is being applied, drawing from work conducted under the Nuclear Plant Aging Research (NPAR) Program, sponsored by the Nuclear Regulatory Commission's (NRCs) Office of Research. Nuclear plants are becoming an increasingly important factor in the national electrical grid. Initiatives are currently underway to extend the operating licenses beyond the current 40-year period and to evaluate advanced reactor designs the feature higher safety factors. Corrosion has not caused a major nuclear accident, but numerous corrosion mechanisms, have degraded nuclear systems and components. New corrosion phenomena continue to appear, and occasionally corrosion phenomena cause reactor shutdowns. Effective application of understanding and managing corrosion is important to safe and economic operation of the nuclear plants and also to public perception of a soundly operated technology. 53 refs., 11 figs., 5 tabs

Nuclear power plant maintenance optimisation SENUF network activity

Energy Technology Data Exchange (ETDEWEB)

Ahlstrand, R.; Bieth, M.; Pla, P.; Rieg, C.; Trampus, P. [Inst. for Energy, EC DG Joint Research Centre, Petten (Netherlands)

2004-07-01

During providing scientific and technical support to TACIS and PHARE nuclear safety programs a large amount of knowledge related to Russian design reactor systems has accumulated and led to creation of a new Network concerning Nuclear Safety in Central and Eastern Europe called ''Safety of Eastern European type Nuclear Facilities'' (SENUF). SENUF contributes to bring together all stakeholders of TACIS and PHARE: beneficiaries, end users, Eastern und Western nuclear industries, and thus, to favour fruitful technical exchanges and feedback of experience. At present the main focus of SENUF is the nuclear power plant maintenance as substantial element of plant operational safety as well as life management. A Working Group has been established on plant maintenance. One of its major tasks in 2004 is to prepare a status report on advanced strategies to optimise maintenance. Optimisation projects have an interface with the plant's overall life management program. Today, almost all plants involved in SENUF network have an explicit policy to extend their service life, thus, component ageing management, modernization and refurbishment actions became much more important. A database is also under development, which intends to help sharing the available knowledge and specific equipment and tools. (orig.)

EDF ageing management program of nuclear components: a safety and economical issue

International Nuclear Information System (INIS)

Faidy, C.

2005-01-01

Ageing management of Nuclear Power Plants is an essential issue for utilities, in term of safety and availability and corresponding economical consequences. Practically all nuclear countries have developed a systematic program to deal with ageing of components on their plants. This paper presents the ageing management program developed by EDF and that are compared with different other approaches in other countries (IAEA guidelines and GALL report). The paper presents a general overview of the programs, the major results, recommendations and conclusions. (author)

ETGAR - Information system for abnormal occurrences in nuclear power plants

International Nuclear Information System (INIS)

Baram, J.; Nagar, M.; Pultorak, G.

1975-01-01

The need for extensive information on systems and components arises early in the planning stage of a nuclear power plant. This information is equally necessary during the building of the plant and during the licensing process. Another type of information helps preventive maintenance during the operating life of the plant. In the case of abnormal occurrences additional information on their possible consequences and on possible ways of handling them, is essential. To cover these four needs, the ETGAR system, which at present covers mostly PWR and BWR type nuclear power plants, collects and evaluates information on abnormal occurrences in nuclear power plants. The information is coded, using a three-level coding scheme for systems and components, and put on magnetic tape. A search program enables the retrieval of any pertinent information from the data base. The sources for the ETGAR data base are reports on abnormal occurrences in nuclear power plants. Most of them are USAEC dockets, originated at U.S.A. power plants. The relevant documents are accessible through a standard query run for ETGAR in the INIS data base which is maintained by the INIS centre in Israel. This query retrieves every two weeks all the documents which come under the ETGAR scope and these are handed as microfiches to the ETGAR evaluators after each INIS run. The evaluation and coding of the documents, the ETGAR coding scheme and the computer programs are described. (B.G.)

Recommendations for managing equipment aging in nuclear power plants

International Nuclear Information System (INIS)

Gunther, W.E.; Subudhi, M.; Aggarwal, S.K.

1992-01-01

Research conducted under the auspices of the US NRC's Nuclear Plant Aging Research (NPAR) Program has resulted in a large database of component and system operating, maintenance, and testing information. This database has been used to determine the susceptibility to aging of selected components, and the potential for equipment aging to impact plant safety and availability. it has also identified methods for detecting and mitigating component and system aging. This paper describes the research recommendations on electrical components which could be applied to maintenance, testing, and inspection activities to detect and mitigate the effects of aging prior to equipment failures

Actions concerning nuclear power plant life evaluation

International Nuclear Information System (INIS)

Chocron, M.; Fabbri, S.; Mizrahi, R.; Savino, E.J.; Versaci, R.A.

1998-01-01

One of the main activities to be undertaken by CNEA will be to provide technological assistance to NASA in problems concerning NPP operation. Works on life extensions of NPP are included in these activities. To fulfill these requirements the Atomic Energy National Commission (CNEA) has constituted a technical committee for Nuclear Power Plants Support (CAPCEN). CAPCEN should be the knowledge reservoir of those issues concerning the performance, safety and life extension of Nuclear Power Plants. One of CAPCEN's most important activities is to promote research work connected with such issues. The main technical areas are: Pressure Vessel and Piping, Heat Exchanges and Fuel Channels and Reactor Inner Components. Efforts are focused on the identification of the main components susceptible of ageing, the study of their ageing mechanisms, the follow-up of their behaviour during operation, and the measures taken to extend their life. (author)

Nuclear power plant ageing and life extension: Safety aspects

International Nuclear Information System (INIS)

Novak, S.; Podest, M.

1987-01-01

Experience with large fossil-fired electrical generating units, as well as in all process industries, shows that plants begin to deteriorate with age after approximately 10 years of operation. Similar phenomena will prevail for nuclear plants, and it is reasonable to postulate that their availability will be affected, as will their safety, if appropriate measures are not taken. It is evident that the average age of power reactors in the IAEA's Member States is increasing. By 2000, more than 50 nuclear plants will have been providing electricity for 25 years or longer. Most nuclear power plants have operating lifetimes of between 20 and 40 years. Ageing is defined as a continuing time-dependent degradation of material due to service conditions, including normal operation and transient conditions. It is common experience that over long periods of time, there is a gradual change in the properties of materials. These changes can affect the capability of engineered components, systems, or structures to perform their required function. Not all changes are deleterious, but it is commonly observed that ageing processes normally involve a gradual reduction in performance capability. All materials in a nuclear power plant can suffer from ageing and can partially or totally lose their designed function. Ageing is not only of concern for active components (for which the probability of malfunction increases with time) but also for passive ones, since the safety margin is being reduced towards the lowest allowable level

Fuel handling and storage systems in nuclear power plants

International Nuclear Information System (INIS)

1984-01-01

The scope of this Guide includes the design of handling and storage facilities for fuel assemblies from the receipt of fuel into the nuclear power plant until the fuel departs from that plant. The unirradiated fuel considered in this Guide is assumed not to exhibit any significant level of radiation so that it can be handled without shielding or cooling. This Guide also gives limited consideration to the handling and storage of certain core components. While the general design and safety principles are discussed in Section 2 of this Guide, more specific design requirements for the handling and storage of fuel are given in detailed sections which follow the general design and safety principles. Further useful information is to be found in the IAEA Technical Reports Series No. 189 ''Storage, Handling and Movement of Fuel and Related Components at Nuclear Power Plants'' and No. 198 ''Guide to the Safe Handling of Radioactive Wastes at Nuclear Power Plants''. However, the scope of the Guide does not include consideration of the following: (1) The various reactor physics questions associated with fuel and absorber loading and unloading into the core; (2) The design aspects of preparation of the reactor for fuel loading (such as the removal of the pressure vessel head for a light water reactor) and restoration after loading; (3) The design of shipping casks; (4) Fuel storage of a long-term nature exceeding the design lifetime of the nuclear power plant; (5) Unirradiated fuel containing plutonium

The use of hardfacing alloys in nuclear power plants

International Nuclear Information System (INIS)

Saarinen, K.; Aaltonen, P.

1987-08-01

In this report the structure and applications of cobalt-, nickel- and iron-based hardfacing alloys are reviewed. Cobalt-based hardfacing alloys are widely used in nuclear power plant components due to their good wear and corrosion resistance. However, the wear and corrosion products of the cobalt-containing alloys are released into the primary cooling water and transported to the reactor core where cobalt (Co-59) is transmuted to the radioactive isotope Co-60. It has been estimated that cobalt-based hardfacing alloys are responsible for up to 90% of the total cobalt released to the primary water circuit. The cobalt based hardfacing alloys are used in such components as valves, control blade pins and pumps, etc. In the Finnish nuclear power plants they are not used in in-core components. The replacement of cobalt-containing alloys in primary cooling system components is studied in many laboratories, but substitutes for the cobalt-based alloys in the complete range of nuclear hardfacing applications have so far not been found. However, the modified austenitic stainless steels have showed good resistance to galling wear and are therefore considered substitutes for cobalt-based alloys

Experience on environmental qualification of safety-related components for Darlington Nuclear Generating Station

International Nuclear Information System (INIS)

Yu, A.S.; Kukreti, B.M.

1987-01-01

The proliferation of Nuclear Power Plant safety concerns has lead to increasing attention over the Environmental Qualification (EQ) of Nuclear Power Plant Safety-Related Components to provide the assurance that the safety related equipment will meet their intended functions during normal operation and postulated accident conditions. The environmental qualification of these components is also a Licensing requirement for Darlington Nuclear Generating Station. This paper provides an overview of EQ and the experience of a pilot project, in the qualification of the Main Moderator System safety-related functions for the Darlington Nuclear Generating Station currently under construction. It addresses the various phases of qualification from the identification of the EQ Safety-Related Components List, definition of location specific service conditions (normal, adbnormal and accident), safety-related functions, Environmental Qualification Assessments and finally, an EQ system summary report for the Main Moderator System. The results of the pilot project are discussed and the methodology reviewed. The paper concludes that the EQ Program developed for Darlington Nuclear Generating Station, as applied to the qualification of the Main Moderator System, contained all the elements necessary in the qualification of safety-related equipment. The approach taken in the qualification of the Moderator safety-related equipment proves to provide a sound framework for the qualification of other safety-related components in the station

Aging of concrete containment structures in nuclear power plants

International Nuclear Information System (INIS)

Naus, D.J.; Oland, C.B.; Ellingwood, B.; Mori, Yasuhiro; Arndt, E.G.

1992-01-01

Concrete structures play a vital role in the safe operation of all light-water reactor plants in the US Pertinent concrete structures are described in terms of their importance design, considerations, and materials of construction. Degradation factors which can potentially impact the ability of these structures to meet their functional and performance requirements are identified. Current inservice inspection requirements for concrete containments are summarized. A review of the performance history of the concrete components in nuclear power plants is provided. A summary is presented. A summary is presented of the Structural Aging (SAG) Program being conducted at the Oak Ridge National Laboratory for the US Nuclear Regulatory Commission. The SAG Program is addressing the aging management of safety-related concrete structures in nuclear power plants for the purpose of providing improved bases for their continued service. The program consists of a management task and three technical tasks: materials property data base, structural component assessment/repair technologies, and quantitiative methodology for continued service conditions. Objectives and a summary of accomplishments under each of these tasks are presented

General description of the Three Mile Island nuclear power plant

International Nuclear Information System (INIS)

Figueras, J.M.

1980-01-01

A general description of systems and components of the Three Mile Island-2 nuclear power plant is presented, for the primary system (NSSS), the secondary system (BOP), the energy generation system and for other auxiliaries in the plant. (author)

Overview of plant life management for long term operation in nuclear power plants

International Nuclear Information System (INIS)

Kang, K.S.; Vincze, P.; Bychkov, A.

2014-01-01

Many IAEA member states have given high priority to licensing their nuclear power plants to operate for terms longer than the time frame originally anticipated (generally 40 years). The task of managing plant ageing is assigned in most member states to an engineering specialty called 'plant life management' (PLiM) applying a systematic analysis methodology to System Structure Components (SSCs) ageing. In many countries, the safety performance of nuclear power plants is periodically assessed and characterized via the periodic safety review (PSR) process. Regulatory review and acceptance of PSRs constitutes for these countries the licensing requirement for continued operation of the plant to the following PSR cycle (usually 10 years). In the USA and in other countries operating US designed plants, instead of PSR process, a license renewal application (LRA) process is followed, which requires certain prerequisites such as ageing management programs, particularly for passive irreplaceable SSCs. Active components are normally addressed via the maintenance rule (MR) requirements and other established regulatory processes. A third group of member states have adopted a combined approach that incorporates elements of both the PSR process and selected LRA specific requirements, such as time limited ageing analysis. The article ends with some IAEA recommendations for the implementation of national PLiM programs

Operator training simulator for nuclear power plant

International Nuclear Information System (INIS)

Shiozuka, Hiromi

1977-01-01

In nuclear power plants, training of the operators is important. In Japan, presently there are two training centers, one is BWR operation training center at Okuma-cho, Fukushima Prefecture, and another the nuclear power generation training center in Tsuruga City, Fukui Prefecture, where the operators of PWR nuclear power plants are trained. This report describes the BWR operation training center briefly. Operation of a nuclear power plant is divided into three stages of start-up, steady state operation, and shut down. Start-up is divided into the cold-state start-up after the shut down for prolonged period due to periodical inspection or others and the hot-state start-up from stand-by condition after the shut down for a short time. In the cold-state start-up, the correction of reactivity change and the heating-up control to avoid excessive thermal stress to the primary system components are important. The BWR operation training center offers the next three courses, namely beginner's course, retraining course and specific training course. The training period is 12 weeks and the number of trainees is eight/course in the beginner's course. The simulator was manufactured by modeling No. 3 plant of Fukushima First Nuclear Power Station, Tokyo Electric Power Co. The simulator is composed of the mimic central control panel and the digital computer. The software system comprises the monitor to supervise the whole program execution, the logic model simulating the plant interlock system and the dynamic model simulating the plant physical phenomena. (Wakatsuki, Y.)

Virtual environments for nuclear power plant design

International Nuclear Information System (INIS)

Brown-VanHoozer, S.A.; Singleterry, R.C. Jr.; King, R.W.

1996-01-01

In the design and operation of nuclear power plants, the visualization process inherent in virtual environments (VE) allows for abstract design concepts to be made concrete and simulated without using a physical mock-up. This helps reduce the time and effort required to design and understand the system, thus providing the design team with a less complicated arrangement. Also, the outcome of human interactions with the components and system can be minimized through various testing of scenarios in real-time without the threat of injury to the user or damage to the equipment. If implemented, this will lead to a minimal total design and construction effort for nuclear power plants (NPP)

Health protection and industrial safety. Nuclear power plants

International Nuclear Information System (INIS)

1987-03-01

The standard applies to primary circuit components including its auxiliary facilities, and of the secondary circuit of nuclear power plants with pressurized water reactors; to lifting gear and load take-ups for the transport of nuclear fuel and primary circuit components; to elevators within the containment, and to electrical installations. Part 3 specifies the behaviour of workers in conformity with safety provisions during operation, inspection, lifetime surveillance, functional testing, and maintenance. Special demands are made on the water regime and on elevators, lifting gear, and load take-ups

Detection and mitigation of aging effects of nuclear power plant components

International Nuclear Information System (INIS)

Pachner, J.

1988-09-01

This paper describes the general principles of the methods for timely detection and mitigation of aging effects. These methods include condition monitoring, failure trending, system reliability monitoring, predictive maintenance and scheduled maintenance. In addition, developments of existing detection and mitigation methods needed to improve the capability for effective managing of nuclear power plant aging are discussed

PWR heavy equipments manufacture for nuclear power plants

International Nuclear Information System (INIS)

Boury, C.; Terrien, J.F.

1983-10-01

The manufacture of boilers has been imported by the French nuclear program to the societe FRAMATOME. FRAMATOME, because of the size of this market, has constructed two special plants for manufacturing of nuclear components (vapor generators, reactor tanks, pressurizers); these two high technical facilities are presented: production, staff training, technical overseas assistance, and technical and economical repercussions on the industrial vicinity [fr

Nuclear power plant safety, the merits of separation

International Nuclear Information System (INIS)

Helander, L.I.; Tiren, L.I.

1977-01-01

The United States AEC General Design Criteria for Nuclear Power Plants are used worldwide as a basis for the assessment of nuclear plant safety. Several of these criteria require redundancy of safety systems, separation of protection and control systems, consideration of natural phenomena, etc. All these criteria point in one particular direction: the necessity for physically separating the various safety-related systems of a nuclear power plant, particularly with regard to single occurrences that may yield a multiple failure. Requirements in this regard have been amplified by the United States NRC Regulatory Guides and by IEEE Standards. The single occurrence that yields a multiple failure may be, for example, fire, pipe whip, missiles, flooding, hurricanes, or lightning. The paper discusses protection, against the quoted events and others, obtained through applying criteria regarding redundancy and separation of safety-related structures, systems and components. Such criteria affect nuclear plant design in many areas, such as building lay-out, arrangements for fire protection and ventilation, separation of mechanical systems and components, in particular emergency cooling systems, and separation of electric equipment and cables. Implementation of the ensuing design criteria for a BWR power plant is described. This design involves the separation of Emergency Cooling Systems into four 50% Capacity Systems which are independent and separated, including the distribution network for electric power from on-site standby diesel generators and the circuitry for the reactor protection system. The plant is subdivided into a number of fire zones each with its own independent ventilation system. The fire zones are further subdivided into a multitude of fire cells such that redundant subsystems are housed in separate cells. These design precautions with regard to fire are complemented by extensive fire fighting systems

IAEA guidance on ageing management for nuclear power plants. Guidance on effective management of the physical ageing of systems, structures and components important to safety for nuclear power plants. Overview. Programmatic guidelines. Component specific guidelines. Review guidelines. Version 1, 2002

International Nuclear Information System (INIS)

2002-01-01

Operational experience shows that excellent plant safety and excellent performance go hand in hand, and that they are achieved by effective leadership and management that includes a unified approach to safety and production. This is also applicable to ageing management. Effective ageing management leads to both enhanced plant safety and enhanced performance and is a prerequisite for long service life. The IAEA project on Safety Aspects of NPP Ageing has produced since 1990 a comprehensive set of programmatic and component specific guidelines on managing ageing, while providing an interactive environment for information exchange and co-operation among practitioners, and has assisted Member States in the application of the guidelines through the provision of training and advice. The objective of the CD-ROM is to preserve the IAEA's guidance on ageing management and to facilitate its retrieval, updating, extension and dissemination in order to help increase the effectiveness of ageing management at nuclear power plants

Technology Trend in the Maintenance of Nuclear Power Plants

International Nuclear Information System (INIS)

Yoon, Kyungsup; Lee, Unjang

2014-01-01

In this paper, overall technology evolution is reviewed and the improvements in the plant safety, reliability and productivity are described. And the issue and some recommendation for better maintenance of Korean nuclear power plants are presented as the interim study results on the 'Management and Regulatory Policy for the Nuclear Power Plant Maintenance and Equipment Reliability' under the agreement with the Nuclear Safety and Security Commission. The future trend in the maintenance technologies is also covered. Maintenance is the essential element for the enhancement of plant safety, reliability and economics and also for public safety. Therefore the regulator's involvements and the utility's active participation is inevitable for the better maintenance. For the better sustainability of our nuclear power plants the followings are recommended. ·Establishment of the good maintenance program and continuous improvement. ·Application of OLM on the safety related and non-safety related components by step-by-step approach. ·Improvement PRA technology for the accurate and reliable risk analysis. ·Continuous training and cultivation for the qualified maintenance personnel

Technology Trend in the Maintenance of Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Yoon, Kyungsup; Lee, Unjang [CTO and CEO, Seoul (Korea, Republic of)

2014-05-15

In this paper, overall technology evolution is reviewed and the improvements in the plant safety, reliability and productivity are described. And the issue and some recommendation for better maintenance of Korean nuclear power plants are presented as the interim study results on the 'Management and Regulatory Policy for the Nuclear Power Plant Maintenance and Equipment Reliability' under the agreement with the Nuclear Safety and Security Commission. The future trend in the maintenance technologies is also covered. Maintenance is the essential element for the enhancement of plant safety, reliability and economics and also for public safety. Therefore the regulator's involvements and the utility's active participation is inevitable for the better maintenance. For the better sustainability of our nuclear power plants the followings are recommended. ·Establishment of the good maintenance program and continuous improvement. ·Application of OLM on the safety related and non-safety related components by step-by-step approach. ·Improvement PRA technology for the accurate and reliable risk analysis. ·Continuous training and cultivation for the qualified maintenance personnel.

General model for Pc-based simulation of PWR and BWR plant components

Energy Technology Data Exchange (ETDEWEB)

Ratemi, W M; Abomustafa, A M [Faculty of enginnering, alfateh univerity Tripoli, (Libyan Arab Jamahiriya)

1995-10-01

In this paper, we present a basic mathematical model derived from physical principles to suit the simulation of PWR-components such as pressurizer, intact steam generator, ruptured steam generator, and the reactor component of a BWR-plant. In our development, we produced an NMMS-package for nuclear modular modelling simulation. Such package is installed on a personal computer and it is designed to be user friendly through color graphics windows interfacing. The package works under three environments, namely, pre-processor, simulation, and post-processor. Our analysis of results using cross graphing technique for steam generator tube rupture (SGTR) accident, yielded a new proposal for on-line monitoring of control strategy of SGTR-accident for nuclear or conventional power plant. 4 figs.

Nuclear power. Volume 1. Nuclear power plant design

International Nuclear Information System (INIS)

Pedersen, E.S.

1978-01-01

NUCLEAR POWER PLANT DESIGN is intended to be used as a working reference book for management, engineers and designers, and as a graduate-level text for engineering students. The book is designed to combine theory with practical nuclear power engineering and design experience, and to give the reader an up-to-date view of the status of nuclear power and a basic understanding of how nuclear power plants function. Volume 1 contains the following chapters; (1) nuclear reactor theory; (2) nuclear reactor design; (3) types of nuclear power plants; (4) licensing requirements; (5) shielding and personnel exposure; (6) containment and structural design; (7) main steam and turbine cycles; (8) plant electrical system; (9) plant instrumentation and control systems; (10) radioactive waste disposal (waste management) and (11) conclusion

Seismic fragilities for nuclear power plant risk studies

International Nuclear Information System (INIS)

Kennedy, R.P.; Ravindra, M.K.

1983-01-01

Seismic fragilities of critical structures and equipment are developed as families of conditional failure frequency curves plotted against peak ground acceleration. The procedure is based on available data combined with judicious extrapolation of design information on plant structures and equipment. Representative values of fragility parameters for typical modern nuclear power plants are provided. Based on the fragility evaluation for about a dozen nuclear power plants, it is proposed that unnecessary conservatism existing in current seismic design practice could be removed by properly accounting for inelastic energy absorption capabilities of structures. The paper discusses the key contributors to seismic risk and the significance of possible correlation between component failures and potential design and construction errors

Nuclear power plants - Quality assurance

International Nuclear Information System (INIS)

1980-01-01

This International Standard defines principles for the establishment and implementation of quality assurance programmes during all phases of design, procurement, fabrication, construction, commissioning, operation, maintenance and decommissioning of structures, systems and components of nuclear power plants. These principles apply to activities affecting the quality of items, such as designing, purchasing, fabricating, handling, shipping, storing, cleaning, erecting, installing, testing, commissioning, operating, inspecting, maintaining, repairing, refuelling and modifying and eventually decommissioning. The manner in which the principles described in this document will be implemented in different organizations involved in a specific nuclear power project will depend on regulatory and contractual requirements, the form of management applied to a nuclear power project, and the nature and scope of the work to be performed by different organizations

Balance of Plant Requirements for a Nuclear Hydrogen Plant

Energy Technology Data Exchange (ETDEWEB)

Bradley Ward

2006-04-01

This document describes the requirements for the components and systems that support the hydrogen production portion of a 600 megawatt thermal (MWt) Next Generation Nuclear Plant (NGNP). These systems, defined as the "balance-of-plant" (BOP), are essential to operate an effective hydrogen production plant. Examples of BOP items are: heat recovery and heat rejection equipment, process material transport systems (pumps, valves, piping, etc.), control systems, safety systems, waste collection and disposal systems, maintenance and repair equipment, heating, ventilation, and air conditioning (HVAC), electrical supply and distribution, and others. The requirements in this document are applicable to the two hydrogen production processes currently under consideration in the DOE Nuclear Hydrogen Initiative. These processes are the sulfur iodide (S-I) process and the high temperature electrolysis (HTE) process. At present, the other two hydrogen production process - the hybrid sulfur-iodide electrolytic process (SE) and the calcium-bromide process (Ca-Br) -are under flow sheet development and not included in this report. While some features of the balance-of-plant requirements are common to all hydrogen production processes, some details will apply only to the specific needs of individual processes.

Nuclear regulation. License renewal questions for nuclear plants need to be resolved

International Nuclear Information System (INIS)

Fultz, Keith O.; Kruslicky, Mary Ann; McDowell, William D. Jr.; Coleman, Robert L.

1989-04-01

need to be resolved, it has made little progress in reaching definitive regulatory conclusions. NRC expects to do so sometime in the early 1990s. Four utilities are studying aging effects on critical systems and components at their nuclear plants. Although the studies have not identified any generic technical obstacles to preclude continued operation, NRC and the utilities are aware of some conditions that could adversely affect the integrity of a reactor. On the basis of its research, NRC has identified 12 plants that may be affected. Alternatives, such as changing the fuel location within the reactor, are available to forestall these conditions. Some utilities have implemented these measures and believe their plants can operate safely for at least 60 years. DOE and the industry are also working to develop and submit the first application to NRC for extended plant operations

ASME Section XI philosophy related to operating nuclear plant fatigue damage protection

International Nuclear Information System (INIS)

Gosselin, S.R.

1995-01-01

When faced with operating fatigue concerns, nuclear plants traditionally look to the requirements contained in the original construction design code, ASME Section 3, as a basis for component operability. These rules constitute the requirements for nuclear power plant vessel and component construction and, when combined with the Owner's Design Specification, provide reasonable assurance of reliable operation. However, once construction is complete and operation begins, the purpose of any subsequent evaluations shifts from component ''design qualification'' to component ''fitness for service.'' This is a role that has been assumed for ASME Section 11. This paper presents a philosophy, recently endorsed by the ASME Section 11 Executive Committee, intended to guide future Code activities regarding fatigue and its impact on component serviceability

Regulatory control of maintenance activities in Argentine nuclear power plants

International Nuclear Information System (INIS)

Calvo, J.C.; Caruso, G.

2000-01-01

The main maintenance objective is to assure that the safety features of structures, components and systems of nuclear power plants are kept as designed. Therefore, there is a direct relationship between safety and maintenance. Owing to the above mentioned, maintenance activities are considered a relevant regulatory issue for the Argentine Nuclear Regulatory Authority (ARN). This paper describes the regulatory control to maintenance activities of Argentine nuclear power plants. It also addresses essential elements for maintenance control, routine inspections, special inspections during planned outages, audits and license conditions and requirements. (author)

Advanced chemistry management system for nuclear power plants

International Nuclear Information System (INIS)

Maeda, Katsuji; Kobayashi, Yasuhiro; Nagasawa, Katsumi

2000-01-01

Chemistry control in a boiling water reactor (BWR) plant has a close relationship with radiation field buildup, fuel reliability, integrity of plant components and materials, performance of the water treatment systems and radioactive waste generation. Chemistry management in BWR plants has become more important in order to maintain and enhance plant reliability. Adequate chemistry control and management are also essential to establish, maintain, and enhance plant availability. For these reasons, we have developed the advanced chemistry management system for nuclear power plants in order to effectively collect and evaluate a large number of plant operating and chemistry data. (author)

Stochastic models and reliability parameter estimation applicable to nuclear power plant safety

International Nuclear Information System (INIS)

Mitra, S.P.

1979-01-01

A set of stochastic models and related estimation schemes for reliability parameters are developed. The models are applicable for evaluating reliability of nuclear power plant systems. Reliability information is extracted from model parameters which are estimated from the type and nature of failure data that is generally available or could be compiled in nuclear power plants. Principally, two aspects of nuclear power plant reliability have been investigated: (1) The statistical treatment of inplant component and system failure data; (2) The analysis and evaluation of common mode failures. The model inputs are failure data which have been classified as either the time type of failure data or the demand type of failure data. Failures of components and systems in nuclear power plant are, in general, rare events.This gives rise to sparse failure data. Estimation schemes for treating sparse data, whenever necessary, have been considered. The following five problems have been studied: 1) Distribution of sparse failure rate component data. 2) Failure rate inference and reliability prediction from time type of failure data. 3) Analyses of demand type of failure data. 4) Common mode failure model applicable to time type of failure data. 5) Estimation of common mode failures from 'near-miss' demand type of failure data

Nuclear power plant ageing management programmes in foreign countries

International Nuclear Information System (INIS)

Simola, K.; Laakso, K.; Pekkonen, A.

1992-09-01

The report describes ageing studies of nuclear power plants and research programmes on plant life extension in foreign countries. Ageing studies are aimed to ascertain that the availability and safety of components and structures can be maintained throughout the plant lifetime. In life extension programmes the purpose is to evaluate the technical and economical possibilities to extend the plant lifetime beyond the originally planned operation period, without reducing the plant safety. The main emphasis of the report is put on the ageing and life extension programmes in the United States. Besides the U.S. studies, research on plant life extension possibilities conducted in France and Japan are also described. Examples of studies performed in other nuclear energy producing countries are given. These examples are mainly related to the development of maintenance programmes and techniques

Large airplane crash on a nuclear plant: Design study against excessive shaking of components

International Nuclear Information System (INIS)

Petrangeli, Gianni

2010-01-01

The problem of the strong shaking of structures and of components in case of an aircraft impact is the subject of this study. This problem is solved in some designs by protecting the external Nuclear Island block (N.I.) by an external thick wall, capable to withstand the aircraft impact. This wall is connected to the rest of the N.I. by the common foundation slab only. The first part of this study consists of the evaluation of the order of magnitude of the vibration attenuation which can be obtained by this design scheme. Should the attenuation obtained be not sufficient for some parts of the internal structures, some additional design provision could be adopted. In order to solve this problem, a specific design solution is here suggested. It essentially consists in connecting critical parts of structures to the common foundation slab with restraints having an adequate degree of deformability, so that the transmission of high frequency impact forces from other parts of the whole structure is minimized. In a previous paper, the structural protection of the reactor dome and of connected structures of a modern nuclear plant is dealt with. In the present paper, the protection of internal parts of the plant (the internal containment is chosen) in case of strong impact on lateral walls is studied. The indicative result of this study is that the enhancement of attenuation in the transmission of acceleration from the impact point to some representative point in the inner structure is of the order of 75. This result cannot be generalized, as it depends on many parameters of the structure and of the soil.

Large airplane crash on a nuclear plant: Design study against excessive shaking of components

Energy Technology Data Exchange (ETDEWEB)

Petrangeli, Gianni, E-mail: g.petrangeli@gmail.i [University of Pisa, Via C. Maes 53, 00162 Roma (Italy)

2010-12-15

The problem of the strong shaking of structures and of components in case of an aircraft impact is the subject of this study. This problem is solved in some designs by protecting the external Nuclear Island block (N.I.) by an external thick wall, capable to withstand the aircraft impact. This wall is connected to the rest of the N.I. by the common foundation slab only. The first part of this study consists of the evaluation of the order of magnitude of the vibration attenuation which can be obtained by this design scheme. Should the attenuation obtained be not sufficient for some parts of the internal structures, some additional design provision could be adopted. In order to solve this problem, a specific design solution is here suggested. It essentially consists in connecting critical parts of structures to the common foundation slab with restraints having an adequate degree of deformability, so that the transmission of high frequency impact forces from other parts of the whole structure is minimized. In a previous paper, the structural protection of the reactor dome and of connected structures of a modern nuclear plant is dealt with. In the present paper, the protection of internal parts of the plant (the internal containment is chosen) in case of strong impact on lateral walls is studied. The indicative result of this study is that the enhancement of attenuation in the transmission of acceleration from the impact point to some representative point in the inner structure is of the order of 75. This result cannot be generalized, as it depends on many parameters of the structure and of the soil.

Fatigue evaluation including environmental effects for primary circuit components in nuclear power plants

International Nuclear Information System (INIS)

Seichter, Johannes; Reese, Sven H.; Klucke, Dietmar

2013-01-01

The influence of LWR coolant environment to the lifetime of materials in Nuclear Power Plants is in discussion internationally. Environmental phenomena were investigated in laboratory tests and published in recent years. The discussion is mainly focused both on the transition from laboratory to real plant components and on numerical calculation procedures. Since publishing of the NUREG/CR-6909 report in 2007, formulae for calculating the Fen factors have been modified several times. Various calculation procedures like the so called 'Strain-integrated Method' and 'Simplified Approach' have been published while each approach yields to different results. The recent revision of the calculation procedure, proposed by ANL in 2012, is presented and discussed with regard to possible variations in the results depending on the assumptions made. In German KTA Rules the effect of environmentally assisted fatigue (EAF) is taken into account by means of so called attention thresholds. If the threshold value is exceeded, further measures like NDT, in-service inspections including fracture mechanical evaluations or detailed assessment procedures have to be performed. One way to handle those measures is to apply sophisticated procedures and to show that the calculated CUF is below the defined attention thresholds. On the basis of a practical example, methods and approaches will be discussed and recommendations in terms of avoiding over-conservatism and misinterpretation will be presented.

Fatigue evaluation including environmental effects for primary circuit components in nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Seichter, Johannes [Siempelkamp Pruef- und Gutachter-Gesellschaft mbH, Dresden (Germany); Reese, Sven H.; Klucke, Dietmar [Component Technology Global Unit Generation, E.ON Kernkraft GmbH, Hannover (Germany)

2013-05-15

The influence of LWR coolant environment to the lifetime of materials in Nuclear Power Plants is in discussion internationally. Environmental phenomena were investigated in laboratory tests and published in recent years. The discussion is mainly focused both on the transition from laboratory to real plant components and on numerical calculation procedures. Since publishing of the NUREG/CR-6909 report in 2007, formulae for calculating the Fen factors have been modified several times. Various calculation procedures like the so called 'Strain-integrated Method' and 'Simplified Approach' have been published while each approach yields to different results. The recent revision of the calculation procedure, proposed by ANL in 2012, is presented and discussed with regard to possible variations in the results depending on the assumptions made. In German KTA Rules the effect of environmentally assisted fatigue (EAF) is taken into account by means of so called attention thresholds. If the threshold value is exceeded, further measures like NDT, in-service inspections including fracture mechanical evaluations or detailed assessment procedures have to be performed. One way to handle those measures is to apply sophisticated procedures and to show that the calculated CUF is below the defined attention thresholds. On the basis of a practical example, methods and approaches will be discussed and recommendations in terms of avoiding over-conservatism and misinterpretation will be presented.

Bayesian methodology for generic seismic fragility evaluation of components in nuclear power plants

International Nuclear Information System (INIS)

Yamaguchi, Akira; Campbell, R.D.; Ravindra, M.K.

1991-01-01

Bayesian methodology for updating the seismic fragility of components in nuclear power plants is presented. The generic fragility data which have been evaluated based on the past SPSAs are combined with the seismic experience data. Although the seismic experience is limited to the acceleration range below the median capacity of the components, it has been found that the evidence is effective to update the fragility tail. In other words, the uncertainty of the fragility is reduced although the median capacity itself is not modified to a great extent. The annual frequency of failure is also reduced as a result of the updating of the fragility tail. The PDF of the seismic capacity is handled in discrete form, which enables the use of arbitrary type of prior distribution. Accordingly, the Log-N prior can be used which is consistent with the widely used fragility model. For evaluating posterior fragility parameters (A m and B U ), two methods have been proposed. Furthermore, it has been found that the importance of evidence used in the Bayesian methodology can be quantified by the entropy of the evidence. Only the events with high entropy need to be considered in the Bayesian updating of the fragility. The currently available seismic experience database for typical components can be utilized to develop the fragility tail which is contributive to the seismically-induced failure frequency. The combined use of generic fragility and seismic experience data, with the aid of Bayesian methodology, provides refined generic fragility curves which are useful for SPSA studies. (author)

Structural experiences at the Kewaunee Nuclear Power Plant

International Nuclear Information System (INIS)

Setlur, A.V.

1983-01-01

This paper discusses the original structural and geotechnical design and subsequent structural experience at the Kewaunee Nuclear Power Plant. The original design of the 535 MWe Westinghouse two loop PWR nuclear plant operated by Wisconsin Public Service Corporation, was started in 1967 and was completed in 1974 when the unit was put into commercial operation. Since 1974 a number of changes in the regulations and additional requirements have been imposed on operating reactors. The paper traces the influence of the original plant criteria on the backfit evaluations and the minimal physical changes required in the plant's structures and components to comply with the new requirements. In addition, the unique design features and construction challenges of the original design are discussed. Kewaunee Nuclear Power Plant has had one of the best operating performance records in the world. Also, the exposure to radiation for plant personnel and radioactive waste generation has been significantly lower than the average. This has been achieved by a conscientious team effort of all parties involved. Some of the more significant structural design features contributing to the excellent performance is detailed in this paper. (orig.)

The licensing practice on nuclear power plants in Korea

Energy Technology Data Exchange (ETDEWEB)

Moon, S P

1994-12-31

The evolution of Korean regulatory system has tightly coupled with development ot Korean nuclear power program. The nuclear power plant licensing has become a major regulatory function of the government when the construction of the Kori NPP Unit 1 started in early 1970s. During this period, domestic laws and regulations applicable to the licensing of NPP were not yet fully developed. Therefore the vendor countries` laws and regulations were applied as mandatory requirement. Beginning in the early 19808, component approach was used and contracts were awarded separately for major components of the plants, thus enabling more domestic industries to participate in the projects. The two-step licensing system was incorporated into the law. In the third phase from 1987, major efforts have been concentrated on the maximum participation of local industries. The overriding priority for selecting suppliers was the condition of higher nuclear technology transfer to Korea. The Korea Institute of Nuclear Safety (KINS) was established in 1990 as an independent regulatory expert organization. 1 tab., 4 figs.

Integrated Nuclear Recycle Plant

International Nuclear Information System (INIS)

Patodi, Anuj; Parashar, Abhishek; Samadhiya, Akshay K.; Ray, Saheli; Dey, Mitun; Singh, K.K.

2017-01-01

Nuclear Recycle Board (NRB), Tarapur proposes to set up an 'Integrated Nuclear Recycle Plant' at Tarapur. This will be located in the premises of BARC facilities. The project location is at coastal town of Tarapur, 130 Km north of Mumbai. Project area cover of INRP is around 80 hectares. The plant will be designed to process spent fuel received from Pressurized Heavy Water Reactors (PHWRs). This is the first large scale integrated plant of the country. INRP will process spent fuel obtained from indigenous nuclear power plants and perform left over nuclear waste disposal

Nuclear power plant safety. The merits of separation

International Nuclear Information System (INIS)

Helander, L.I.; Tiren, L.I.

1977-01-01

The paper illustrates how the physical separation of safety-related structures, systems and components can improve the protection of a nuclear power plant against multiple failures that may be caused by events such as fire, pipe-whip, missiles, flooding, hurricanes, lightning etc. Criteria for redundancy and separation requirements affect nuclear plant design in many areas such as building layout, arrangements for fire protection and ventilation, separation of mechanical systems and components, in particular emergency cooling systems, separation of electric equipment and cables. The implementation of the ensuing design criteria for a BWR power plant is described. This design involves the separation of emergency cooling systems into four 50% capacity systems, which are independent and separated, including the distribution network for electric power from on-site standby diesel generators and the circuitry for the reactor protection system. The plant is subdivided into a number of fire zones, each with its own independent ventilation system. The fire zones are further subdivided into a multitude of fire cells such that redundant subsystems are housed in separate cells. These design precautions with regard to fire are complemented by extensive fire fighting systems. (author)

Qualification of quality assurance program audit personnel for nuclear power plants - August 1980

International Nuclear Information System (INIS)

Anon.

1981-01-01

Appendix B, Quality Assurance Criteria for Nuclear Power Plants and Fuel Reprocessing Plants, to 10 CFR Part 50, Domestic Licensing of Production and Utilization Facilities, establishes overall quality assurance requirements for the design, construction, and operation of safety-related structures, and components of nuclear power plants. Criterion XVIII, Audits, of Appendix B establishes requirements for conducting audits of the quality assurance program. This guide describes a method acceptable to the NRC staff for complying with the Commission's regulations with regard to qualification of quality assurance program audit personnel for nuclear power plants

Safety and operation of the Stade nuclear power plant

International Nuclear Information System (INIS)

Salcher, H.

1991-01-01

The concept of PreussenElektra is to continuously increase the existing safety standard of the Stade nuclear power station using experience gained from faults and operation in nuclear power stations and the progressive state of the art. Modifications to achieve the most gentle operation of the plant have been completed and other are on-going. To do so instruments were attached to those components which are susceptible to fatigue to record the transients and extensive calculatory records were kept. Although the plant has almost 20 years successful operation behind it, it can still stand up well to comparisons with more recent plants as far as safety aspects are concerned. 6 figs

Experience in monitoring ageing phenomena for improving nuclear power plant availability. Proceedings of a specialists' meeting. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-07-01

For more than thirty years nuclear power plants have been supplying electricity to national grids. Today, the nuclear power community is facing great challenges. The safe, reliable operation of existing nuclear power plants (NPPs) must continue to be ensured. From an economic viewpoint, because of the long lead times associated with bringing new plants into service, securing the continued operation of existing plants for their planned lifetimes and possible life extension will be very important in the near term for meeting electrical power demands. The IAEA programmes in nuclear power plant ageing and life extension and in control and instrumentation promote technical information exchange between Member States with new programmes, offers assistance to Member States with an interest in reliability of NPP components, in-service inspection methods and programmes using on-line techniques, component monitoring and special technological topics of nuclear reactors. Significant experience already exists in the nuclear industry in developing and applying the monitoring techniques for different nuclear power plant applications, especially in monitoring of ageing phenomena for improving NPP availability. The purpose of this Specialists' Meeting was to bring together experts from operations, design, research and development and licensing to share their experience in: ageing mechanics of key structural components, methods of monitoring such ageing, tools for cost-effective implementation of the methods and methodologies, life management approaches and examples from current reactors, future direction for monitoring of key structural components in nuclear power plants. The meeting was organized by the IAEA International Working Groups on Life Management of Nuclear Power Plants (IWG-LMNPP) and Nuclear Power Plant Control and Instrumentation (TWG-NPPCI) in co-operation with the Czechoslovak Atomic Energy Commission and Skoda concern. Around 40 participants from 10 countries.

Experience in monitoring ageing phenomena for improving nuclear power plant availability. Proceedings of a specialists' meeting. Working material

International Nuclear Information System (INIS)

1992-01-01

For more than thirty years nuclear power plants have been supplying electricity to national grids. Today, the nuclear power community is facing great challenges. The safe, reliable operation of existing nuclear power plants (NPPs) must continue to be ensured. From an economic viewpoint, because of the long lead times associated with bringing new plants into service, securing the continued operation of existing plants for their planned lifetimes and possible life extension will be very important in the near term for meeting electrical power demands. The IAEA programmes in nuclear power plant ageing and life extension and in control and instrumentation promote technical information exchange between Member States with new programmes, offers assistance to Member States with an interest in reliability of NPP components, in-service inspection methods and programmes using on-line techniques, component monitoring and special technological topics of nuclear reactors. Significant experience already exists in the nuclear industry in developing and applying the monitoring techniques for different nuclear power plant applications, especially in monitoring of ageing phenomena for improving NPP availability. The purpose of this Specialists' Meeting was to bring together experts from operations, design, research and development and licensing to share their experience in: ageing mechanics of key structural components, methods of monitoring such ageing, tools for cost-effective implementation of the methods and methodologies, life management approaches and examples from current reactors, future direction for monitoring of key structural components in nuclear power plants. The meeting was organized by the IAEA International Working Groups on Life Management of Nuclear Power Plants (IWG-LMNPP) and Nuclear Power Plant Control and Instrumentation (TWG-NPPCI) in co-operation with the Czechoslovak Atomic Energy Commission and Skoda concern. Around 40 participants from 10 countries

Anlagen- und Kraftwerksrohrleitungsbau Greifswald GmbH plan and build wet decontamination plant for disposal of components of Russian nuclear submarines

International Nuclear Information System (INIS)

Schneider, Jan; Konitzer, Arnold; Luedeke, Michael

2010-01-01

Anlagen- und Kraftwerksrohrleitungsbau Greifswald, on behalf of Energiewerke Nord GmbH, Lubmin, plan and build a wet decontamination facility for the waste management center at Saida Bay, Russia (EZS). The plant is part of a large project with a total volume on the order of 3-digit millions funded by the German Federal Ministry for Economics and Technology. This project involves construction at Saida Bay near the port city of Murmansk of a complete waste management center and a long-term interim store for radioactively contaminated components. These components are mainly parts of decommissioned nuclear vessels and submarines whose metals, after decontamination, can be returned to economic use. The basis of the wet decontamination plant is a former AKB project for disposal and re-use of contaminated metal components of Energiewerke Nord GmbH at Lubmin, which is being adapted and developed further. The plant is to allow unrestricted re-use of the metals after surface cleaning and surface abrasion, respectively. For this purpose, the contaminated layer is removed far enough for the clearance limits under the Radiation Protection Ordinance to be met. A large fraction of the metals can be re-used after cleaning and do not have to be stored in a financially and logistically expensive process. The contract gives AKB an excellent opportunity to demonstrate its capabilities in plant construction, especially in the very sensitive area of disposal of radioactively contaminated objects. (orig.)

Quality assurance program manual for nuclear power plants. Volume I. Policies

International Nuclear Information System (INIS)

1976-01-01

The Consumers Power Company Quality Assurance Program Manual for Nuclear Power Plants consists of policies and procedures which comply with current NRC regulatory requirements and industry codes and standards in effect during the design, procurement, construction, testing, operation, refueling, maintenance, repair and modification activities associated with nuclear power plants. Specific NRC and industry documents that contain the requirements, including the issue dates in effect, are identified in each nuclear power plant's Safety Analysis Report. The requirements established by these documents form the basis for the Consumer Power Quality Assurance Program, which is implemented to control those structures, systems, components and operational safety actions listed in each nuclear power plant's Quality List (Q-List). As additional and revised requirements are issued by the NRC and professional organizations involved in nuclear activities, they will be reviewed for their impact on this manual, and changes will be made where considered necessary. CP Co 1--Consumers Power Company QA Program Topical Report is Volume I of this manual and contains Quality Assurance Program Policies applicable during all phases of nuclear power plant design, construction and operation

Treatment of core components from nuclear power plants with PWR and BWR reactors - 16043

International Nuclear Information System (INIS)

Viermann, Joerg; Friske, Andreas; Radzuweit, Joerg

2009-01-01

During operation of a Nuclear Power Plant components inside the RPV get irradiated. Irradiation has an effect on physical properties of these components. Some components have to be replaced after certain neutron doses or respectively after a certain operating time of the plant. Such components are for instance water channels and control rods from Boiling Water Reactors (BWR) or control elements, poisoning elements and flow restrictors from Pressurized Water Reactors (PWR). Most of these components are stored in the fuel pool for a certain time after replacement. Then they have to be packaged for further treatment or for disposal. More than 25 years ago GNS developed a system for disposal of irradiated core components which was based on a waste container suitable for transport, storage and disposal of Intermediate Level Waste (ILW), the so-called MOSAIK R cask. The MOSAIK R family of casks is subject of a separate presentation at the ICEM 09 conference. Besides the MOSAIK R cask the treatment system developed by GNS comprised underwater shears to cut the components to size as well as different types of equipment to handle the components, the shears and the MOSAIK R casks in the fuel pool. Over a decade of experience it showed that this system although effective needed improvement for BWR plants where many water channels and control rods had to be replaced after a certain operating time. Because of the large numbers of components the time period needed to cut the components in the pool had a too big influence on other operational work like rearranging of fuel assemblies in the pool. The system was therefore further developed and again a suitable cask was the heart of the solution. GNS developed the type MOSAIK R 80 T, a cask that is capable to ship the unsegmented components with a length of approx. 4.5 m from the Power plants to an external treatment centre. This treatment centre consisting of a hot cell installation with a scrap shear, super-compactor and a heavy

Nuclear Plant Aging Research (NPAR) program plan

International Nuclear Information System (INIS)

1985-07-01

The nuclear plant aging research described in this plan is intended to resolve issues related to the aging and service wear of equipment and systems at commercial reactor facilities and their possible impact on plant safety. Emphasis has been placed on identification and characterization of the mechansims of material and component degradation during service and evaluation of methods of inspection, surveillance, condition monitoring and maintenance as means of mitigating such effects. Specifically the goals of the program are as follows: (1) to identify and characterize aging and service wear effects which, if unchecked, could cause degradation of structures, components, and systems and thereby impair plant safety; (2) to identify methods of inspection, surveillance and monitoring, or of evaluating residual life of structures, components, and systems, which will assure timely detection of significant aging effects prior to loss of safety function; and (3) to evaluate the effectiveness of storage, maintenance, repair and replacement practices in mitigating the rate and extent of degradation caused by aging and service wear

Nuclear plant simulation using the Nuclear Plant Analyzer

International Nuclear Information System (INIS)

Beelman, R.J.; Laats, E.T.; Wagner, R.J.

1984-01-01

The Nuclear Plant Analyzer (NPA), a state-of-the-art computerized safety analysis and engineering tool, was employed to simulate nuclear plant response to an abnormal transient during a training exercise at the US Nuclear Regulatory Commission (USNRC) in Washington, DC. Information relative to plant status was taken from a computer animated color graphics display depicting the course of the transient and was transmitted to the NRC Operations Center in a manner identical to that employed during an actual event. Recommendations from the Operations Center were implemented during on-line, interactive execution of the RELAP5 reactor systems code through the NPA allowing a degree of flexibility in training exercises not realized previously. When the debriefing was conducted, the RELAP5 calculations were replayed by way of the color graphics display, adding a new dimension to the debriefing and greatly enhancing the critique of the exercise

Design, maintenance and lifetime of nuclear components

International Nuclear Information System (INIS)

Noel, R.L.; Eisenhut, D.G.; Carey, J.J.; Reynes, L.J.

1989-01-01

Division D of SMiRT deals with experience feedback relating to the in-service behavior of nuclear components, the design and construction of this equipment, its maintenance and the evaluation and management of its lifetime. The nuclear industry now having reached maturity, with more than 300 units in service worldwide, these problems are now of predominant importance to the activity of the industry and in its development programs. This applies particularly to the problems relating to the lifetime of nuclear plants, problems which are rightly of such concern both to the utilities, in view of the enormous investments involved, and also to the safety authorities. These contributions have been reviewed for the purpose of analyzing the essential points. This analysis highlights the considerable advances achieved during the recent decades in design and maintenance methods and practices. It also identifies the areas in which progress still remains to be made

Automatic acoustic and vibration monitoring system for nuclear power plants

International Nuclear Information System (INIS)

Tothmatyas, Istvan; Illenyi, Andras; Kiss, Jozsef; Komaromi, Tibor; Nagy, Istvan; Olchvary, Geza

1990-01-01

A diagnostic system for nuclear power plant monitoring is described. Acoustic and vibration diagnostics can be applied to monitor various reactor components and auxiliary equipment including primary circuit machinery, leak detection, integrity of reactor vessel, loose parts monitoring. A noise diagnostic system has been developed for the Paks Nuclear Power Plant, to supervise the vibration state of primary circuit machinery. An automatic data acquisition and processing system is described for digitalizing and analysing diagnostic signals. (R.P.) 3 figs

A pilot application of risk-based methods to establish in-service inspection priorities for nuclear components at Surry Unit 1 Nuclear Power Station

International Nuclear Information System (INIS)

Vo, T.; Gore, B.; Simonen, F.; Doctor, S.

1994-08-01

As part of the Nondestructive Evaluation Reliability Program sponsored by the US Nuclear Regulatory Commission, the Pacific Northwest Laboratory is developing a method that uses risk-based approaches to establish in-service inspection plans for nuclear power plant components. This method uses probabilistic risk assessment (PRA) results and Failure Modes and Effects Analysis (FEMA) techniques to identify and prioritize the most risk-important systems and components for inspection. The Surry Nuclear Power Station Unit 1 was selected for pilot applications of this method. The specific systems addressed in this report are the reactor pressure vessel, the reactor coolant, the low-pressure injection, and the auxiliary feedwater. The results provide a risk-based ranking of components within these systems and relate the target risk to target failure probability values for individual components. These results will be used to guide the development of improved inspection plans for nuclear power plants. To develop inspection plans, the acceptable level of risk from structural failure for important systems and components will be apportioned as a small fraction (i.e., 5%) of the total PRA-estimated risk for core damage. This process will determine target (acceptable) risk and target failure probability values for individual components. Inspection requirements will be set at levels to assure that acceptable failure probabilistics are maintained

Economics of Nuclear Power Plant and the development of nuclear power in Viet Nam

International Nuclear Information System (INIS)

Thanh, Thuy Nguyen Thi; Song, JinHo; Ha, Kwang Soon

2015-01-01

There are many factors affecting the capital costs like: increased plant size, multiple unit construction, improved construct methods, increase the lifetime of plant and so on, and beside is technical to enhancing the safety for NPPs. For the question that whether building a NPP is really economic than other energy resources or not, we will find the answer by comparing the USD per kWh of different energy sources as: nuclear power, coal, oil, hydro natural energy sources. The situation of energy in Vietnam was also mentioned in this paper. Vietnam has an abundant natural resources likes: coal, gas, hydro power etc, but from year 2013 to now Vietnam facing of electricity shortage and to solve the problem, Vietnam Government has chosen nuclear power energy to achieve energy balance between the rate of energy consumption and the ability to energy supply. Eight units will be built in Vietnam and in October 2014 Vietnamese officials have chosen Rosatom's AES-2006 design with VVER-1200/v-491 reactors for country's first nuclear power plant at Ninh Thuan and a second plant should follow based on a partnership with Japan. In this paper, the breakdown of NPP costs is considered. All the costs for building a NPP includes: the investment costs are the largest components (about 60%), fuel costs (15%), O and M costs (25%) and external costs are lower than 1% of the kWh costs. The situation for energy in Vietnam was mentioned with increase annually by 5.5 %, and now the shortage electricity is the big problem in power section. The purpose of this report is to give a general picture to consider the cost of nuclear power. It includes all the costs for building a nuclear power plant like total capital investment costs, production costs, external costs in which the capital investment costs is the largest component of the kWh cost. Nuclear energy Power was chosen to deal with situation of diminishing resources shortages

Economics of Nuclear Power Plant and the development of nuclear power in Viet Nam

Energy Technology Data Exchange (ETDEWEB)

Thanh, Thuy Nguyen Thi; Song, JinHo [University of Science and Technology, Daejeon (Korea, Republic of); Ha, Kwang Soon [KAERI, Daejeon (Korea, Republic of)

2015-05-15

There are many factors affecting the capital costs like: increased plant size, multiple unit construction, improved construct methods, increase the lifetime of plant and so on, and beside is technical to enhancing the safety for NPPs. For the question that whether building a NPP is really economic than other energy resources or not, we will find the answer by comparing the USD per kWh of different energy sources as: nuclear power, coal, oil, hydro natural energy sources. The situation of energy in Vietnam was also mentioned in this paper. Vietnam has an abundant natural resources likes: coal, gas, hydro power etc, but from year 2013 to now Vietnam facing of electricity shortage and to solve the problem, Vietnam Government has chosen nuclear power energy to achieve energy balance between the rate of energy consumption and the ability to energy supply. Eight units will be built in Vietnam and in October 2014 Vietnamese officials have chosen Rosatom's AES-2006 design with VVER-1200/v-491 reactors for country's first nuclear power plant at Ninh Thuan and a second plant should follow based on a partnership with Japan. In this paper, the breakdown of NPP costs is considered. All the costs for building a NPP includes: the investment costs are the largest components (about 60%), fuel costs (15%), O and M costs (25%) and external costs are lower than 1% of the kWh costs. The situation for energy in Vietnam was mentioned with increase annually by 5.5 %, and now the shortage electricity is the big problem in power section. The purpose of this report is to give a general picture to consider the cost of nuclear power. It includes all the costs for building a nuclear power plant like total capital investment costs, production costs, external costs in which the capital investment costs is the largest component of the kWh cost. Nuclear energy Power was chosen to deal with situation of diminishing resources shortages.

Study on the Operating Strategy of HVAC Systems for Nuclear Decommissioning Plant

Energy Technology Data Exchange (ETDEWEB)

Kim, Sung-hwan; Han, Sung-heum; Lee, Jae-gon [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

According as Kori nuclear power plant unit 1 was determined to be defueled in 2017, various studies on nuclear plant decommissioning have been performed. In nuclear decommissioning plant, HVAC systems with large fan and electric coil have to be operated for long periods of time to support various types of work from defueled phase to final dismantling phase. So, in view of safety and utility costs, their overall operating strategy need to be established prior to defueled phase. This study presents HVAC system operating strategy at each decommissioning phase, that is, defueled plant operating phase, SSCs(systems, structures, components) decontamination and dismantling phases. In defueled plant operating phase, all fuel assemblies in reactor vessel are transferred to spent fuel pool(SFP) permanently. In defueled plant operation phase, reduction of the operating system trains is more practicable than the introduction of new HVAC components with reduced capacity. And, based on the result of the accident analyses for this phase, HVAC design bases such as MCR habitability requirement can be mitigated. According to these results, associated SSCs also can be downgraded. In similar approach, at each phase of plant decommissioning, proper inside design conditions and operating strategies should be re-established.

Modifications to nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2004-01-01

control and that the modified configuration conforms to the approved basis for granting a nuclear power plant operating licence. The main purpose of the recommendations concerning changes of management is to give general guidance on performing those changes in such a way that the safety of the plant is not compromised. This Safety Guide deals with the intended modification of structures, systems and components, operational limits and conditions, procedures and software, and the management systems and tools for the operation of a nuclear power plant. The recommendations made cover the whole modification process, from conception to completion. The justification for undertaking modifications is outside the scope of this Safety Guide. The modification and/or refurbishment of nuclear power plants for the purpose of extending the design lifetime could necessitate many major design modifications and special re-evaluation of plant safety (see Ref. [2]), and is therefore outside the scope of this publication. Section 2 gives guidance on general methods for modifications that could be implemented at nuclear power plants. Section 3 identifies the roles and responsibilities of various organizations involved in the modification process. Sections 4 and 5 give guidance on the different types of modification and their assessment in respect of safety aspects, and Section 4 provides guidelines on subsequent categorization. Section 6 deals with aspects of temporary modifications. Sections 7 and 8 give guidance on implementation of different types of modifications. Sections 9, 10 and 11 give basic recommendations on quality assurance, training and management of documentation. Comprehensive guidance on these matters can be found in the appropriate Safety Guides

Modifications to nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2007-01-01

control and that the modified configuration conforms to the approved basis for granting a nuclear power plant operating licence. The main purpose of the recommendations concerning changes of management is to give general guidance on performing those changes in such a way that the safety of the plant is not compromised. This Safety Guide deals with the intended modification of structures, systems and components, operational limits and conditions, procedures and software, and the management systems and tools for the operation of a nuclear power plant. The recommendations made cover the whole modification process, from conception to completion. The justification for undertaking modifications is outside the scope of this Safety Guide. The modification and/or refurbishment of nuclear power plants for the purpose of extending the design lifetime could necessitate many major design modifications and special re-evaluation of plant safety, and is therefore outside the scope of this publication. Section 2 gives guidance on general methods for modifications that could be implemented at nuclear power plants. Section 3 identifies the roles and responsibilities of various organizations involved in the modification process. Sections 4 and 5 give guidance on the different types of modification and their assessment in respect of safety aspects, and Section 4 provides guidelines on subsequent categorization. Section 6 deals with aspects of temporary modifications. Sections 7 and 8 give guidance on implementation of different types of modifications. Sections 9, 10 and 11 give basic recommendations on quality assurance, training and management of documentation. Comprehensive guidance on these matters can be found in the appropriate Safety Guides

Nuclear power plant outages

International Nuclear Information System (INIS)

1998-01-01

The Finnish Radiation and Nuclear Safety Authority (STUK) controls nuclear power plant safety in Finland. In addition to controlling the design, construction and operation of nuclear power plants, STUK also controls refuelling and repair outages at the plants. According to section 9 of the Nuclear Energy Act (990/87), it shall be the licence-holder's obligation to ensure the safety of the use of nuclear energy. Requirements applicable to the licence-holder as regards the assurance of outage safety are presented in this guide. STUK's regulatory control activities pertaining to outages are also described

NPAR [Nuclear Plant Aging Research] approach to managing aging in nuclear power plants

International Nuclear Information System (INIS)

Christensen, J.A.

1989-01-01

Over the past 5 years, the Nuclear Plant Aging Research program (NPAR) has been devoted to developing technical understanding of the time dependent processes that, through deterioration of components, systems, or structures (C/S/S), can reduce safety margins in nuclear power plants. A major and necessary element of the program involves the application of this basic knowledge in defining functional approaches to managing aging by anticipating and mitigating important deterioration processes. Fundamental understanding and characterization of aging processes are being accomplished through NPAR-sponsored research projects, review and analysis of aging related information, integration of NPAR results with those from industry and other aging studies, and interfacing of all of these with the existing body of codes, standards and regulatory instruments that convey aging-related guidance to NPP licensees. Products of these efforts are applied to structuring and providing aging-related technical recommendations in forms that are useful in: (1) developing and implementing good aging management practices, (2) developing regulatory guidance and requirements for understanding and managing aging during normal plant operations and in support of license renewal, and (3) planning and implementing other regulatory actions and initiatives in which aging-related concerns have a bearing on scope or priority

Nuclear power plant control and instrumentation activities in Finland

International Nuclear Information System (INIS)

Haapanen, P.; Wahlstroem, B.

1992-01-01

Finland has remarkable achievements in nuclear power. The existing four plants have some of the best operating records in the world - high capacity factors, low occupational doses and short refuelling outages. Public opinion was strongly turned against nuclear power after Chernobyl accident, and the previous government decided not to allow for the construction of a fifth nuclear unit during its period of reign. The opposition has however slowly been diminishing. According to the latest polls the opinion is almost balanced. Finnish power companies are going to file an application for a decision-in-principle to build a new plant to the new government appointed in April 1991. A readiness to start new construction project immediately after a positive political decision is made has been maintained during the intermediate period. Continuous research, development, modification and upgrading work provide important components of the good operational history of the Finnish nuclear power plants. Efforts have also been devoted to identifying possible new problems arising from the use of distributed digital C and I technology. The following a short description is summarizing recent activities related to the C and I-systems of the nuclear power plants. (author). 3 tab

Risk-benefit evaluation of nuclear power plant siting

International Nuclear Information System (INIS)

Miettinen, J.; Savolainen, I.; Silvennoinen, P.

1976-01-01

An assessment scheme is described for the risk-benefit analyses of nuclear power versus conventional alternatives. Given the siting parameters for the proposed nuclear plant an economic comparison is made with the most advantageous competitive conventional production scenario. The economic benefit is determined from the differential discounted annual energy procurement cost as a function of the real interest rate and amortization time. The risk analysis encompasses the following factors: radiation risks in normal operation, reactor accident hazards and economic risks, atmospheric pollutants from the conventional power plants, and fuel transportation. The hazards are first considered in terms of probabilistic dose distributions. In the second stage risk components are converted to a compatible form where excess mortality is used as the risk indicator. Practical calculations are performed for the power production alternatives of Helsinki where district heat would be extracted from the nuclear power plant. At the real interest rate of 10% and amortization time of 20 yr the 1000 MW(e) nuclear option is found to be Pound9.1 m per yr more economic than the optimal conventional scenario. Simultaneously the nuclear alternative is estimated to reduce excess mortality by 2 to 5 fatal injuries annually. (author)

Nuclear power plant operation experience - a feedback programme

International Nuclear Information System (INIS)

Banica, I.; Sociu, F.; Margaritescu, C.

1994-01-01

An effective high quality maintenance programme is required for the safe reliable operation of a nuclear power plant. To achieve the objectives of such a programme, both plant management and staff must be highly dedicated and motivated to perform high quality work at all levels. Operating and maintenance experience data collections and analysis are necessary in order to enhance the safety of the plant and reliability of the structures systems and components throughout their operating life. Significant events, but also minor incident, may reveal important deficiencies or negative trends adverse to safety. Therefore, a computer processing system for collecting, classifying and evaluating abnormal events or findings concerning operating-maintenance and for feeding back the results of the lessons learned from experience into the design and the operation of our nuclear power plant is considered to be of paramount importance. (Author)

Seismic safety of nuclear power plants in Eastern Europe

International Nuclear Information System (INIS)

Gurpinar, A.; Godoy, A.

1995-01-01

This paper summarizes the work performed by the International Atomic Energy Agency in the areas of safety reviews and applied research in support of programmes for the assessment and enhancement of seismic safety in WWER type nuclear power plants during the past five years. Three major topics are discussed; engineering safety review services in relation to external events, technical guidelines for the assessment and upgrading of WWER type nuclear power plants, and the Coordinated Research Programme on B enchmark study for the seismic analysis and testing of WWER type nuclear power plants . These topics are summarized in a way to provide an overview of the past and present safety situation in selected WWER type plants which are all located in Eastern European countries. Main conclusion of the paper is that although there is now a thorough understanding of the seismic safety issues in these operating nuclear power plants, the implementation of seismic upgrades to structures, systems and components are lagging behind, particularly for those cases in which the re-evaluation indicated the necessity to strengthen the safety related structures or install new safety systems. (author)

Operation of Finnish nuclear power plants. Quarterly report 3rd, quarter 1995

International Nuclear Information System (INIS)

Sillanpaeae, T.

1996-05-01

Quarterly Reports on the operation of Finnish nuclear power plants describe events and observations relating to nuclear and radiation safety which the Finnish Centre for Radiation and Nuclear Safety (STUK) considers safety significant. Safety improvements at the plants are also described. The Report includes a summary of the radiation safety of plant personnel and of the environment and tabulated data on the plants' production and load factors. Except for the annual maintenance outages of Loviisa plant units and for TVO II's brief outage to repair a failed component, Finnish nuclear power plant units were in power operation in the third quarter of 1995. The load factor average of all plant units was 90.4 %. Events in this quarter were level 0 on the INES scale. Occupational doses and radioactive releases off-site were below authorised limits. Radioactive substances were measurable in samples collected around the plants in such quantities only as have no bearing on the radiation exposure of the population. (orig.) (4 figs., 4 tabs.)

Operation of Finnish nuclear power plants. Quarterly report 3rd, quarter 1995

Energy Technology Data Exchange (ETDEWEB)

Sillanpaeae, T [ed.

1996-05-01

Quarterly Reports on the operation of Finnish nuclear power plants describe events and observations relating to nuclear and radiation safety which the Finnish Centre for Radiation and Nuclear Safety (STUK) considers safety significant. Safety improvements at the plants are also described. The Report includes a summary of the radiation safety of plant personnel and of the environment and tabulated data on the plants` production and load factors. Except for the annual maintenance outages of Loviisa plant units and for TVO II`s brief outage to repair a failed component, Finnish nuclear power plant units were in power operation in the third quarter of 1995. The load factor average of all plant units was 90.4 %. Events in this quarter were level 0 on the INES scale. Occupational doses and radioactive releases off-site were below authorised limits. Radioactive substances were measurable in samples collected around the plants in such quantities only as have no bearing on the radiation exposure of the population. (orig.) (4 figs., 4 tabs.).

[Risk communication in construction of new nuclear power plant].

Science.gov (United States)

He, Gui-Zhen; Lü, Yong-Long

2013-03-01

Accompanied by construction of new nuclear power plants in the coming decades in China, risk management has become increasingly politicized and contentious. Nuclear risk communication is a critical component in helping individuals prepare for, respond to, and recover from nuclear power emergencies. It was discussed that awareness of trust and public attitudes are important determinants in nuclear power risk communication and management. However, there is limited knowledge about how to best communicate with at-risk populations around nuclear power plant in China. To bridge this gap, this study presented the attitudinal data from a field survey in under-building Haiyang nuclear power plant, Shandong Province to measure public support for and opposition to the local construction of nuclear power plant. The paper discussed the structure of the communication process from a descriptive point of view, recognizing the importance of trust and understanding the information openness. The results showed that decision-making on nuclear power was dominated by a closed "iron nuclear triangle" of national governmental agencies, state-owned nuclear enterprises and scientific experts. Public participation and public access to information on nuclear constructions and assessments have been marginal and media was a key information source. As information on nuclear power and related risks is very restricted in China, Chinese citizens (51%) tend to choose the government as the most trustworthy source. More respondents took the negative attitudes toward nuclear power plant construction around home. It drew on studies about risk communication to develop some guidelines for successful risk communication. The conclusions have vast implications for how we approach risk management in the future. The findings should be of interest to state and local emergency managers, community-based organizations, public health researchers, and policy makers.

Automatic scheduling of maintenance work in nuclear power plants

International Nuclear Information System (INIS)

Kasahara, T.; Nishizawa, Y.; Kato, K.; Kiguchi, T.

1987-01-01

An automatic scheduling method for maintenance work in nuclear power plants has been developed using an AI technique. The purpose of this method is to help plant operators by adjusting the time schedule of various kinds of maintenance work so that incorrect ordering or timing of plant manipulations does not cause undersirable results, such as a plant trip. The functions of the method were tested by off-line simulations. The results show that the method can produce a satisfactory schedule of plant component manipulations without interference between the tasks and plant conditions

The effects of age on nuclear power plant containment cooling systems

Energy Technology Data Exchange (ETDEWEB)

Lofaro, R.; Subudhi, M.; Travis, R.; DiBiasio, A.; Azarm, A. [Brookhaven National Lab., Upton, NY (United States); Davis, J. [Science Applications International Corp., New York, NY (United States)

1994-04-01

A study was performed to assess the effects of aging on the performance and availability of containment cooling systems in US commercial nuclear power plants. This study is part of the Nuclear Plant Aging Research (NPAR) program sponsored by the US Nuclear Regulatory Commission. The objectives of this program are to provide an understanding of the aging process and how it affects plant safety so that it can be properly managed. This is one of a number of studies performed under the NPAR program which provide a technical basis for the identification and evaluation of degradation caused by age. The effects of age were characterized for the containment cooling system by reviewing and analyzing failure data from national databases, as well as plant-specific data. The predominant failure causes and aging mechanisms were identified, along with the components that failed most frequently. Current inspection, surveillance, and monitoring practices were also examined. A containment cooling system unavailability analysis was performed to examine the potential effects of aging by increasing failure rates for selected components. A commonly found containment spray system design and a commonly found fan cooler system design were modeled. Parametric failure rates for those components in each system that could be subject to aging were accounted for in the model to simulate the time-dependent effects of aging degradation, assuming no provisions are made to properly manage it. System unavailability as a function of increasing component failure rates was then calculated.

The effects of age on nuclear power plant containment cooling systems

International Nuclear Information System (INIS)

Lofaro, R.; Subudhi, M.; Travis, R.; DiBiasio, A.; Azarm, A.; Davis, J.

1994-04-01

A study was performed to assess the effects of aging on the performance and availability of containment cooling systems in US commercial nuclear power plants. This study is part of the Nuclear Plant Aging Research (NPAR) program sponsored by the US Nuclear Regulatory Commission. The objectives of this program are to provide an understanding of the aging process and how it affects plant safety so that it can be properly managed. This is one of a number of studies performed under the NPAR program which provide a technical basis for the identification and evaluation of degradation caused by age. The effects of age were characterized for the containment cooling system by reviewing and analyzing failure data from national databases, as well as plant-specific data. The predominant failure causes and aging mechanisms were identified, along with the components that failed most frequently. Current inspection, surveillance, and monitoring practices were also examined. A containment cooling system unavailability analysis was performed to examine the potential effects of aging by increasing failure rates for selected components. A commonly found containment spray system design and a commonly found fan cooler system design were modeled. Parametric failure rates for those components in each system that could be subject to aging were accounted for in the model to simulate the time-dependent effects of aging degradation, assuming no provisions are made to properly manage it. System unavailability as a function of increasing component failure rates was then calculated

Progress of nuclear safety for symbiosis and sustainability advanced digital instrumentation, control and information systems for nuclear power plants

CERN Document Server

Yoshikawa, Hidekazu

2014-01-01

This book introduces advanced methods of computational and information systems allowing readers to better understand the state-of-the-art design and implementation technology needed to maintain and enhance the safe operation of nuclear power plants. The subjects dealt with in the book are (i) Full digital instrumentation and control systems and human?machine interface technologies (ii) Risk? monitoring methods for large and? complex? plants (iii) Condition monitors for plant components (iv) Virtual and augmented reality for nuclear power plants and (v) Software reliability verification and val

Distributed Control Systems in New Nuclear Power Plants

International Nuclear Information System (INIS)

Doerfler, Joseph

2008-01-01

With the growing demand for energy many countries have expressed interest in constructing new plants over the next 15 to 20 years. These expectations have presented a challenge to the nuclear industry to provide a high volume of construction. A key strategy to meet this challenge is developing an advanced nuclear power plant design that allows for a modular construction, a high level of standardization, passive safety features, reduced number of components, and a short bid-to-build time. In addition, the implementation of the plant control system has evolved as new technologies emerge to support these goals. The purpose of this paper is to discuss the ways that the distributed control and information systems in the new generation of nuclear power plants will differ from those currently in service. The new designs provide opportunities to improve overall performance through the use of bus technology, a video display driven Human System Interface, enhanced diagnostics and improved maintenance features. However, the new technologies must fully address requirements for cyber security and high reliability. This paper will give an overview of new technology, improvements, as well as emerging issues in new plant design. (authors)

Distributed Control Systems in New Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Doerfler, Joseph [Westinghouse Electric Company, 4350 Northern Pike, Monroeville, PA 15146 (United States)

2008-07-01

With the growing demand for energy many countries have expressed interest in constructing new plants over the next 15 to 20 years. These expectations have presented a challenge to the nuclear industry to provide a high volume of construction. A key strategy to meet this challenge is developing an advanced nuclear power plant design that allows for a modular construction, a high level of standardization, passive safety features, reduced number of components, and a short bid-to-build time. In addition, the implementation of the plant control system has evolved as new technologies emerge to support these goals. The purpose of this paper is to discuss the ways that the distributed control and information systems in the new generation of nuclear power plants will differ from those currently in service. The new designs provide opportunities to improve overall performance through the use of bus technology, a video display driven Human System Interface, enhanced diagnostics and improved maintenance features. However, the new technologies must fully address requirements for cyber security and high reliability. This paper will give an overview of new technology, improvements, as well as emerging issues in new plant design. (authors)

Trend analyses of the emergency diesel generator problem events in Japanese and U.S. nuclear power plants

International Nuclear Information System (INIS)

Shimada, Yoshio

2011-01-01

Up to 2009, the author and a colleague conducted trend analyses of problem events related to main generators, emergency diesel generators, breakers, motors and transformers which are more likely to cause problems than other electric components in nuclear power plants. Among the electric components with high frequency of defect occurrence, i.e., emergency diesel generators, several years have passed since the last analyses. These are very important components needed to stop a nuclear reactor safely and to cool it down during external power supply loses. Then trend analyses were conducted for the second time. The trend analyses were performed on 80 problem events with emergency diesel generators which had occurred in U.S. nuclear power plants in the five years from 2005 through 2009 among events reported in the Licensee Event Reports (LERs: event reports submitted to NRC by U.S. nuclear power plants) which have been registered in the nuclear information database of the Institute of Nuclear Safety System, Inc. (INSS) , as well as 40 events registered in the Nuclear Information Archives (NUCIA), which occurred in Japanese nuclear power plants in the same time period. It was learned from the trend analyses of the problem events with emergency diesel generators that frequency of defect occurrence are high in both Japanese and US plants during plant operations and functional tests (that is, defects can be discovered effectively in advance), so that implementation of periodical functional tests under plant operation is an important task for the future. (author)

Report on aging of nuclear power plant reinforced concrete structures

International Nuclear Information System (INIS)

Naus, D.J.; Oland, C.B.; Ellingwood, B.R.

1996-03-01

The Structural Aging Program provides the US Nuclear Regulatory Commission with potential structural safety issues and acceptance criteria for use in continued service assessments of nuclear power plant safety-related concrete structures. The program was organized under four task areas: Program Management, Materials Property Data Base, Structural Component Assessment/Repair Technology, and Quantitative Methodology for Continued Service Determinations. Under these tasks, over 90 papers and reports were prepared addressing pertinent aspects associated with aging management of nuclear power plant reinforced concrete structures. Contained in this report is a summary of program results in the form of information related to longevity of nuclear power plant reinforced concrete structures, a Structural Materials Information Center presenting data and information on the time variation of concrete materials under the influence of environmental stressors and aging factors, in-service inspection and condition assessments techniques, repair materials and methods, evaluation of nuclear power plant reinforced concrete structures, and a reliability-based methodology for current and future condition assessments. Recommendations for future activities are also provided. 308 refs., 61 figs., 50 tabs

Report on aging of nuclear power plant reinforced concrete structures

Energy Technology Data Exchange (ETDEWEB)

Naus, D.J.; Oland, C.B. [Oak Ridge National Lab., TN (United States); Ellingwood, B.R. [Johns Hopkins Univ., Baltimore, MD (United States). Dept. of Civil Engineering

1996-03-01

The Structural Aging Program provides the US Nuclear Regulatory Commission with potential structural safety issues and acceptance criteria for use in continued service assessments of nuclear power plant safety-related concrete structures. The program was organized under four task areas: Program Management, Materials Property Data Base, Structural Component Assessment/Repair Technology, and Quantitative Methodology for Continued Service Determinations. Under these tasks, over 90 papers and reports were prepared addressing pertinent aspects associated with aging management of nuclear power plant reinforced concrete structures. Contained in this report is a summary of program results in the form of information related to longevity of nuclear power plant reinforced concrete structures, a Structural Materials Information Center presenting data and information on the time variation of concrete materials under the influence of environmental stressors and aging factors, in-service inspection and condition assessments techniques, repair materials and methods, evaluation of nuclear power plant reinforced concrete structures, and a reliability-based methodology for current and future condition assessments. Recommendations for future activities are also provided. 308 refs., 61 figs., 50 tabs.

Safety prediction technique for nuclear power plants

International Nuclear Information System (INIS)

Henry, C.D. III; Anderson, R.T.

1985-01-01

This paper presents a safety prediction technique (SPT) developed by Reliability Technology Associates (RTA) for nuclear power plants. It is based on a technique applied by RTA to assess the flight safety of US Air Force aircraft. The purpose of SPT is to provide a computerized technique for objective measurement of the effect on nuclear plant safety of component failure or procedural, software, or human error. A quantification is determined, called criticality, which is proportional to the probability that a given component or procedural-human action will cause the plant to operate in a hazardous mode. A hazardous mode is characterized by the fact that there has been a failure/error and the plant, its operating crew, and the public are exposed to danger. Whether the event results in an accident, an incident, or merely the exposure to danger is dependent on the skill and reaction of the operating crew as well as external influences. There are three major uses of SPT: (a) to predict unsafe situations so that corrective action can be taken before accidents occur, (b) to quantify the impact of equipment malfunction or procedural, software, or human error on safety and thereby establish priorities for proposed modifications, and (c) to provide a means of evaluating proposed changes for their impact on safety prior to implementation and to provide a method of tracking implemented changes

Risk monitor riskangel for risk-informed applications in nuclear power plants

International Nuclear Information System (INIS)

Wang, Fang; Wang, Jiaqun; Wang, Jin; Li, Yazhou; Hu, Liqin; Wu, Yican

2016-01-01

Highlights: • A general risk monitor riskangel with high-speed cutsets generator engine. • Benchmarks of actual nuclear power plant (NPP) instantaneous risk models. • Applications in daily operation, maintenance plan and component out of service. - Abstract: This paper studied the requirements of risk monitor software and its applications as a plant specific risk monitor, which supports risk-informed configuration risk management for the two CANDU 6 units at the Third Qinshan nuclear power plant (TQNPP) in China. It also describes the regulatory prospective on risk-informed Probabilistic Safety Assessment (PSA) applications and the use of risk monitor at operating nuclear power plants, high level technical and functional requirements for the development of CANDU specific risk monitor software, and future development trends.

Nuclear power plant life management

International Nuclear Information System (INIS)

Rorive, P.; Berthe, J.; Lafaille, J.P.; Eussen, G.

1998-01-01

Several definitions can be given to the design life of a nuclear power plant just as they can be attributed to the design life of an industrial installation: the book-keeping life which is the duration of the provision for depreciation of the plant, the licensed life which corresponds to the duration for which the plant license has been granted and beyond which a new license should be granted by the safety authorities, the design life which corresponds to the duration specified for ageing and fatigue calculations in the design of some selected components during the plant design phase, the technical life which is the duration of effective technical operation and finally the economic life corresponding to the duration of profitable operation of the plant compared with other means of electricity production. Plant life management refers to the measures taken to cope with the combination of licensed, design, technical and economical life. They can include repairs and replacements of components which have arrived to the end of their life due to known degradation processes such as fatigue, embrittlement, corrosion, wear, erosion, thermal ageing. In all cases however, it is of great importance to plan the intervention so as to minimise the economic impact. Predictive maintenance is used together with in-service inspection programs to fulfil this goal. The paper will go over the methodologies adopted in Belgium in all aspects of electrical, mechanical and civil equipment for managing plant life. (author)

Managing aging in nuclear power plants: Insights from NRC's maintenance team inspection reports

International Nuclear Information System (INIS)

Fresco, A.; Subudhi, M.

1994-01-01

Age-related degradation is managed through the maintenance program of a nuclear plant. From 1988 to 1991, the Nuclear Regulatory Commission (NRC) evaluated the maintenance program of every nuclear power plant in the United States. The authors reviewed 44 out of a total of 67 of the reports issued by the NRC on these in-depth team inspections. The reports were reviewed for insights into the strengths and weaknesses of the programs as related to the need to understand and manage the effects of aging on nuclear plant structures, systems, and components. The authors' conclusions are presented. 6 refs

Nuclear power plant fire protection: philosophy and analysis

International Nuclear Information System (INIS)

Berry, D.L.

1980-05-01

This report combines a fire severity analysis technique with a fault tree methodology for assessing the importance to nuclear power plant safety of certain combinations of components and systems. Characteristics unique to fire, such as propagation induced by the failure of barriers, have been incorporated into the methodology. By applying the resulting fire analysis technique to actual conditions found in a representative nuclear power plant, it is found that some safety and nonsafety areas are both highly vulnerable to fire spread and impotant to overall safety, while other areas prove to be of marginal importance. Suggestions are made for further experimental and analytical work to supplement the fire analysis method

French nuclear plant safeguard pump qualification testing: EPEC test loop

International Nuclear Information System (INIS)

Guesnon, H.

1985-01-01

This paper reviews the specifications to which nuclear power plant safeguard pumps must be qualified, and surveys the qualification methods and program used in France to verify operability of the pump assembly and major pump components. The EPEC test loop is described along with loop capabilities and acheivements up to now. This paper shows, through an example, the Medium Pressure Safety Injection Pump designed for service in 1300 MW nuclear power plants, and the interesting possibilities offered by qualification testing

Failure data collection from a Swedish nuclear power plant

International Nuclear Information System (INIS)

Andersson, B.; Bhattacharyya, A.; Hilding, S.

1975-01-01

The Swedish nuclear utilities have formed a joint working group in the field of reliability data of thermal power plants, nuclear and fossil fuelled. The primary task of the working group is to create a standard procedure of collecting failure data from the Swedish nuclear power plants in operation. The failure data will be stored in a joint data bank. A first test collection of such data has been implemented on Oskarshamn I, and the experience with this work is discussed in this report. Reliability analysis of an engineering system is based on the availability of pertinent information on the system components. Right from the beginning within the Swedish nuclear industry the consensus has been that such data can be suitably obtained by monitoring the operating power stations. This has led to a co-operative arrangement between the vendor, ASEA-ATOM and a utility, Oskarshamnsverkets Kraftgrupp AB (OKG) to utilize information from component malfunctions in the reliability analysis. The utility prepares component failure reports which are sent to the vendor for further treatment. Experience gathered to date indicates that this arrangement is effective although many persons are involved in this process of information transmittal. The present set-up is flexible enough to accommodate necessary changes in view of problems which arise now and then in monitoring a complex system like a nuclear power station. This report briefly describes the structure of the failure data collection system. The way in which the raw data collection is done in the station by the owner and the subsequent data processing by the vendor is discussed. A brief status report of the information collected since 1971 is given. It can be concluded that valuable reliability data can be obtained by monitoring component failure reports from an operating power plant. Two requirements are, however, that all the parties involved in the arrangement follow given instructions carefully and that the assumed

Air-conditioning and ventilation systems and components of nuclear facilities

International Nuclear Information System (INIS)

2006-01-01

The Guide defines the requirements for the design, implementation and operation of the air-conditioning and ventilation systems of nuclear facilities belonging to safety classes 3 and 4, and for the related documents to be submitted to STUK (Radiation and Nuclear Safety Authority, Finland). Furthermore, the Guide describes the inspections of air-conditioning and ventilation systems to be conducted by STUK during construction and operation of the facilities. As far as systems and components belonging to safety class 2 are concerned, STUK sets additional requirements case by case. In general, air-conditioning systems refer to systems designed to manage the indoor air cleanness, temperature, humidity and movement. In some rooms of a nuclear power plant, ventilation systems are also used to prevent radioactive materials from spreading outside the rooms. Guide YVL1.0 defines the safety principles concerning the air-conditioning and ventilation of nuclear power plants. Guide YVL2.0 gives the requirements for the design of nuclear power plant systems. In addition, YVLGuide groups 3, 4, 5 and 7 deal with the requirements for air-conditioning and ventilation systems with regard to the mechanical equipment, fire prevention, electrical systems, instrumentation and control technology, and the restriction of releases. The rules and regulations issued by the Ministry of the Environment and the Ministry of the Interior (RakMK, the Finnish building code) concerning the design and operation of air-conditioning and ventilation systems and the related fire protection design bases also apply to nuclear facilities. Exhaust gas treatment systems, condenser vacuum systems of boiling water reactor plants and leak collection systems are excluded from the scope of this Guide

General criteria for the project of nuclear fuel reprocessing plants

International Nuclear Information System (INIS)

1979-01-01

Recommendations are presented establishing the general criteria for the project of nuclear fuel reprocessing plants to be licensed according to the legislation in effect. They apply to all the plant's systems, components and structures which are important to operation safety and to the public's health and safety. (F.E.) [pt

People detection in nuclear plants by video processing for safety purpose

Energy Technology Data Exchange (ETDEWEB)

Jorge, Carlos Alexandre F.; Mol, Antonio Carlos A., E-mail: calexandre@ien.gov.b, E-mail: mol@ien.gov.b [Instituto de Engenharia Nuclear (IEN/CNEN), Rio de Janeiro, RJ (Brazil); Seixas, Jose M.; Silva, Eduardo Antonio B., E-mail: seixas@lps.ufrj.b, E-mail: eduardo@lps.ufrj.b [Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Eletrica; Cota, Raphael E.; Ramos, Bruno L., E-mail: brunolange@poli.ufrj.b [Universidade Federal do Rio de Janeiro (EP/UFRJ), RJ (Brazil). Dept. de Engenharia Eletronica e de Computacao

2011-07-01

This work describes the development of a surveillance system for safety purposes in nuclear plants. The final objective is to track people online in videos, in order to estimate the dose received by personnel, during the execution of working tasks in nuclear plants. The estimation will be based on their tracked positions and on dose rate mapping in a real nuclear plant at Instituto de Engenharia Nuclear, Argonauta nuclear research reactor. Cameras have been installed within Argonauta's room, supplying the data needed. Both video processing and statistical signal processing techniques may be used for detection, segmentation and tracking people in video. This first paper reports people segmentation in video using background subtraction, by two different approaches, namely frame differences, and blind signal separation based on the independent component analysis method. Results are commented, along with perspectives for further work. (author)

People detection in nuclear plants by video processing for safety purpose

International Nuclear Information System (INIS)

Jorge, Carlos Alexandre F.; Mol, Antonio Carlos A.; Seixas, Jose M.; Silva, Eduardo Antonio B.; Cota, Raphael E.; Ramos, Bruno L.

2011-01-01

This work describes the development of a surveillance system for safety purposes in nuclear plants. The final objective is to track people online in videos, in order to estimate the dose received by personnel, during the execution of working tasks in nuclear plants. The estimation will be based on their tracked positions and on dose rate mapping in a real nuclear plant at Instituto de Engenharia Nuclear, Argonauta nuclear research reactor. Cameras have been installed within Argonauta's room, supplying the data needed. Both video processing and statistical signal processing techniques may be used for detection, segmentation and tracking people in video. This first paper reports people segmentation in video using background subtraction, by two different approaches, namely frame differences, and blind signal separation based on the independent component analysis method. Results are commented, along with perspectives for further work. (author)

Wireless online position monitoring of manual valve types for plant configuration management in nuclear power plants

International Nuclear Information System (INIS)

Agarwal, Vivek; Buttles, John W.; Beaty, Lawrence H.; Naser, Joseph; Hallbert, Bruce P.

2016-01-01

In the current competitive energy market, the nuclear industry is committed to lower the operations and maintenance cost; increase productivity and efficiency while maintaining safe and reliable operation. The present operating model of nuclear power plants is dependent on large technical staffs that put the nuclear industry at long-term economic disadvantage. Technology can play a key role in nuclear power plant configuration management in offsetting labor costs by automating manually performed plant activities. The technology being developed, tested, and demonstrated in this paper will enable the continued safe operation of today’s fleet of light water reactors by providing the technical means to monitor components in plants today that are only routinely monitored through manual activities. The wireless enabled valve position indicators that are the subject of this paper are able to provide a valid position indication available continuously, rather than only periodically. As a result, a real-time (online) availability of valve positions using an affordable technologies are vital to plant configuration when compared with long-term labor rates, and provide information that can be used for a variety of plant engineering, maintenance, and management applications.

Nuclear power plant siting

International Nuclear Information System (INIS)

Sulkiewicz, M.; Navratil, J.

The construction of a nuclear power plant is conditioned on territorial requirements and is accompanied by the disturbance of the environment, land occupation, population migration, the emission of radioactive wastes, thermal pollution, etc. On the other hand, a nuclear power plant makes possible the introduction of district heating and increases the economic and civilization activity of the population. Due to the construction of a nuclear power plant the set limits of negative impacts must not be exceeded. The locality should be selected such as to reduce the unfavourable effects of the plant and to fully use its benefits. The decision on the siting of the nuclear power plant is preceded by the processing of a number of surveys and a wide range of documentation to which the given criteria are strictly applied. (B.H.)

The human contribution to nuclear power plant emergencies

International Nuclear Information System (INIS)

Reason, J.

1987-01-01

The safety of present and future nuclear power plants is considered, with particular reference to the human components of these plants. The approach by the United Kingdom Nuclear Installations Inspectorate is particularly criticised. In particular, objections are made to the use of event and fault tree analyses. The UK NII have also decided that comprehensive quantification of human reliability is not feasible. However, figures presented show that the human contribution to monitored power plant emergencies is high, by far the greatest proportion of root causes of emergencies were attributable to human performance. The origins of, and problems with, 'principle 124' are discussed. Automatic safety systems are also distrusted. Current probabilistic risk assessment and probabilistic safety analysis is seen as an unsatisfactory basis for the setting of safety targets. (UK)

Mechanization devices for maintenance of technological components of nuclear power plant primary circuit

International Nuclear Information System (INIS)

Palicka, L.; Blazek, J.

1987-01-01

Selected mechanization devices are described, developed for assembly and repair jobs and for decontamination of the steam generator, the main closing valve and the main circulating pump of a WWER-440 nuclear power plant. (author). 8 figs., 3 tabs., 10 refs

IAEA activity on operator support systems in nuclear power plants

International Nuclear Information System (INIS)

Dounaev, V.; Fujita, Y.; Juslin, K.; Haugset, K.; Lux, I.; Naser, J.

1994-01-01

Various operator support systems for nuclear power plants are already operational or under development in the IAEA Member States. Operator support systems are based on intelligent data processing and, in addition to plant operation, they are also becoming more important for safety. A key feature of operator support systems is their availability to restructure data to increase its relevance for a given situation. This can improve the user's ability to identify plant mode, system state, and component state and to identify and diagnose faults. Operator support systems can also assist the user in planning and implementing corrective actions to improve the nuclear power plant's availability and safety. In September 1991, the IAEA Committee for Contractual Scientific Services approved the Co-ordinated Research Programme (CRP) on ''Operator Support Systems in Nuclear Power Plants'' in the framework of the Project ''Man-Machine Interface Studies''. The main objective of this programme is to provide guidance and technology transfer for the development and implementation of operator support systems. This includes the experience with human-machine interfaces and closely related issues such as instrumentation and control, the use of computers in nuclear power plants, and operator qualification. (author)

Maintenance risk management in Dayabay nuclear power plant

International Nuclear Information System (INIS)

He Xuhong; Tong Jiejuan

2005-01-01

The importance of proper maintenance to safe and reliable nuclear plant operation has long been recognized by the nuclear utility and regulatory body. This paper presents a process of maintenance risk management developed for a Chinese Nuclear Power Plant (NPP). The process includes three phases: (I) long term maintenance plan risk management, (II) monthly maintenance plan risk management, and (III) detailed risk management for high risk configuration. A risk matrix is developed for phase I whose purpose is to provide a rough guide for risk management in the making of the annual maintenance plan. For Phase II and Phase III, a software tool named Maintenance- Risk-Monitor is developed based on the internal initiating event, level 1 PSA model. The results of Phase II are the risk information of the all plant configurations caused by the unavailability of the components included the monthly maintenance plan. When the increase of core damage frequency (CDF) or the incremental core damage probability (ICDP) of a configuration is higher than the corresponding thresholds, Phase III is needed for this high risk configuration to get the useful information such as risk-importance components, human actions and initial events, from which appropriate preventive measurements could be derived. It is hoped that the provided process of maintenance risk management, together with the developed software tool, could facilitate the maintenance activities in the NPPs of China. (authors)

A review of procedures available to seismically requalify operating nuclear plant structures, equipment and distribution systems

International Nuclear Information System (INIS)

Stevenson, J.D.

1985-01-01

It is well known that the loads and procedures used to seismically qualify nuclear power plant structures and components have changed dramatically during the past 15 to 20 years. In this paper, the various methods available to seismically qualify or requalify structures and components in operating nuclear power plants are identified and the advantages and disadvantages of each briefly summarized. (orig.)

Requirements for advanced simulation of nuclear reactor and chemicalseparation plants.

Energy Technology Data Exchange (ETDEWEB)

Palmiotti, G.; Cahalan, J.; Pfeiffer, P.; Sofu, T.; Taiwo, T.; Wei,T.; Yacout, A.; Yang, W.; Siegel, A.; Insepov, Z.; Anitescu, M.; Hovland,P.; Pereira, C.; Regalbuto, M.; Copple, J.; Willamson, M.

2006-12-11

This report presents requirements for advanced simulation of nuclear reactor and chemical processing plants that are of interest to the Global Nuclear Energy Partnership (GNEP) initiative. Justification for advanced simulation and some examples of grand challenges that will benefit from it are provided. An integrated software tool that has its main components, whenever possible based on first principles, is proposed as possible future approach for dealing with the complex problems linked to the simulation of nuclear reactor and chemical processing plants. The main benefits that are associated with a better integrated simulation have been identified as: a reduction of design margins, a decrease of the number of experiments in support of the design process, a shortening of the developmental design cycle, and a better understanding of the physical phenomena and the related underlying fundamental processes. For each component of the proposed integrated software tool, background information, functional requirements, current tools and approach, and proposed future approaches have been provided. Whenever possible, current uncertainties have been quoted and existing limitations have been presented. Desired target accuracies with associated benefits to the different aspects of the nuclear reactor and chemical processing plants were also given. In many cases the possible gains associated with a better simulation have been identified, quantified, and translated into economical benefits.

Development of a SPV management program for nuclear power plants

International Nuclear Information System (INIS)

Lee, Eun-Chan; Na, Jang-Hwan; Lee, Doo-Young; Oh, Seong-Jong; Jerng, Dong-Wook

2009-01-01

The Single Point Vulnerability (SPV) is a characteristic of a component whose failure results in plant transients. KHNP (Korea Hydro and Nuclear Power Co.) has evaluated major systems with critical components and developed a SPV management program to reduce the trip frequency and to raise plant's availability. This study includes a comprehensive methodology for SPV evaluation and its results. This methodology consists of the qualitative evaluation focused on the SPV component list preparation and the quantitative evaluation through FMEA (Failure Mode Effect Analyses) and FTA (Fault Tree Analyses) of critical systems. The qualitative evaluation reduced differences of the SPV lists between the identically designed plants and established strategies for the improvement of the SPV component reliability. The quantitative evaluation identified additional SPV components and developed the fault tree model for a Trip Monitor which showed logic relationships of channel components in the trip-related systems. (author)

Nuclear power plant decommissioning. The nature of problems

Energy Technology Data Exchange (ETDEWEB)

Yunus, Yaziz

1986-04-01

A number of issues have to be taken into account before the introduction of any nuclear power plant in any country. These issues include reactor safety (site and operational), waste disposal and, lastly, the decommissioning of the reactor inself. Because of the radioactive nature of the components, nuclear power plants require a different approach to decommission compared to other plants. Until recently, issues on reactor safety and waste disposal were the main topics discussed. As for reactor decommissioning, the debates have been academic until now. Although reactors have operated for 25 years, decommissioning of retired reactors has simply not been fully planned. But the Shippingport Atomic Power Plant in Pennysylvania, the first large-scale power reactor to be retired, is now being decommissioned. The work has rekindled the debate in the light of reality. Outside the United States, decommissioning is also being confronted on a new plane.

Safety related terms for advanced nuclear plants

International Nuclear Information System (INIS)

1995-12-01

The terms considered in this document are in widespread current use without a universal consensus as to their meaning. Other safety related terms are already defined in national or international codes and standards as well as in IAEA's Nuclear Safety Standards Series. Most of the terms in those codes and standards have been defined and used for regulatory purposes, generally for application to present reactor designs. There is no intention to duplicate the description of such regulatory terms here, but only to clarify the terms used for advanced nuclear plants. The following terms are described in this paper: Inherent safety characteristics, passive component, active component, passive systems, active system, fail-safe, grace period, foolproof, fault-/error-tolerant, simplified safety system, transparent safety

Safety related terms for advanced nuclear plants

International Nuclear Information System (INIS)

1991-09-01

The terms considered in this document are in widespread current use without a universal consensus as to their meaning. Other safety related terms are already defined in national or international codes and standards as well as in IAEA's Nuclear Safety Standards Series. Most of the terms in those codes and standards have been defined and used for regulatory purposes, generally for application to present reactor designs. There is no intention to duplicate the description of such regulatory terms here, but only to clarify the terms used for advanced nuclear plants. The following terms are described in this paper: Inherent safety characteristics, passive component, active component, passive systems, active system, fail-safe, grace period, foolproof, fault-/error-tolerant, simplified safety system, transparent safety

Application of Advanced Technology to Improve Plant Performance in Nuclear Power Plants

International Nuclear Information System (INIS)

Hashemian, H.M.

2011-01-01

Advances in computer technologies, signal processing, analytical modeling, and the advent of wireless sensors have provided the nuclear industry with ample means to automate and optimize maintenance activities and improve safety, efficiency, and availability, while reducing costs and radiation exposure to maintenance personnel. This paper provides a review of these developments and presents examples of their use in the nuclear power industry and the financial and safety benefits that they have produced. As the current generation of nuclear power plants have passed their mid-life, increased monitoring of their health is critical to their safe operation. This is especially true now that license renewal of nuclear power plants has accelerated, allowing some plants to operate up to 60 years or more. Furthermore, many utilities are maximizing their power output through uprating projects and retrofits. This puts additional demand and more stress on the plant equipment such as the instrumentation and control (I and C) systems and the reactor internal components making them more vulnerable to the effects of aging, degradation, and failure. In the meantime, the nuclear power industry is working to reduce generation costs by adopting condition-based maintenance strategies and automation of testing activities. These developments have stimulated great interest in on-line monitoring (OLM) technologies and new diagnostic and prognostic methods to anticipate, identify, and resolve equipment and process problems and ensure plant safety, efficiency, and immunity to accidents. The foundation for much of the required technologies has already been established through 40 years of research and development (R and D) efforts performed by numerous organizations, scientists, and engineers around the world including the author. This paper provides examples of these technologies and demonstrates how the gap between some of the more important R and D efforts and end users have been filled

Images of nuclear power plants

International Nuclear Information System (INIS)

Hashiguchi, Katsuhisa; Misumi, Jyuji; Yamada, Akira; Sakurai, Yukihiro; Seki, Fumiyasu; Shinohara, Hirofumi; Misumi, Emiko; Kinjou, Akira; Kubo, Tomonori.

1995-01-01

This study was conducted to check and see, using Hayashi's quantification method III, whether or not the respondents differed in their images of a nuclear power plant, depending on their demographic variables particularly occupations. In our simple tabulation, we compared subject groups of nuclear power plant employees with general citizens, nurses and students in terms of their images of a nuclear power plant. The results were that while the nuclear power plant employees were high in their evaluations of facts about a nuclear power plant and in their positive images of a nuclear power plant, general citizens, nurses and students were overwhelmingly high in their negative images of a nuclear power plant. In our analysis on category score by means of the quantification method III, the first correlation axis was the dimension of 'safety'-'danger' and the second correlation axis was the dimension of 'subjectivity'-'objectivity', and that the first quadrant was the area of 'safety-subjectivity', the second quadrant was the area of 'danger-subjectivity', the third quadrant as the area of 'danger-objectivity', and the forth quadrant was the area of 'safety-objectivity'. In our analysis of sample score, 16 occupation groups was compared. As a result, it was found that the 16 occupation groups' images of a nuclear power plant were, in the order of favorableness, (1) section chiefs in charge, maintenance subsection chiefs, maintenance foremen, (2) field leaders from subcontractors, (3) maintenance section members, operation section members, (4) employees of those subcontractors, (5) general citizens, nurses and students. On the 'safety-danger' dimension, nuclear power plant workers on the one hand and general citizens, nurses and students on the other were clearly divided in terms of their images of a nuclear power plant. Nuclear power plant workers were concentrated in the area of 'safety' and general citizens, nurses and students in the area of 'danger'. (J.P.N.)

Safety aspects of nuclear power plant ageing

International Nuclear Information System (INIS)

1990-01-01

The nuclear community is facing new challenges as commercial nuclear power plants (NPPs) of the first generation get older. At present, some of the plants are approaching or have even exceeded the end of their nominal design life. Experience with fossil fired power plants and in other industries shows that reliability of NPP components, and consequently general plant safety and reliability, may decline in the middle and later years of plant life. Thus, the task of maintaining operational safety and reliability during the entire plant life and especially, in its later years, is of growing importance. Recognizing the potential impact of ageing on plant safety, the IAEA convened a Working Group in 1985 to draft a report to stimulate relevant activities in the Member States. This report provided the basis for the preparation of the present document, which included a review in 1986 by a Technical Committee and the incorporation of relevant results presented at the 1987 IAEA Symposium on the Safety Aspects of the Ageing and Maintenance of NPPs and in available literature. The purpose of the present document is to increase awareness and understanding of the potential impact of ageing on plant safety; of ageing processes; and of the approach and actions needed to manage the ageing of NPP components effectively. Despite the continuing growth in knowledge on the subject during the preparation of this report it nevertheless contains much that will be of interest to a wide technical and managerial audience. Furthermore, more specific technical publications on the evaluation and management of NPP ageing and service life are being developed under the Agency's programme, which is based on the recommendations of its 1988 Advisory Group on NPP ageing. Refs, figs and tabs

Design of comprehensive plant information system considering maintenance indicators in nuclear power plant

International Nuclear Information System (INIS)

Takata, Takashi; Yamaguchi, Akira; Yamamoto, Akio

2013-01-01

A safety of a nuclear power plant must be ensured and maintained through its entire plant life. For this plant life cycle safety (PLCS), a comprehensive plant information system, in which an each maintenance record of the plant is taken into consideration, is of importance. In this paper, a development of a plant chart, which is a part of the information system, has been developed based on a defense-in-depth concept that is one of the most important concept to ensure the plant safety. In the chart, an updated probability of loss of a component or function is used as a maintenance indicator and a probabilistic risk assessment (PRA) method is applied to quantify the plant status in the chart. (author)