WorldWideScience

Sample records for non-selective deposit feeders

  1. Nitrogen fixed by cyanobacteria is utilized by deposit-feeders.

    Science.gov (United States)

    Karlson, Agnes M L; Gorokhova, Elena; Elmgren, Ragnar

    2014-01-01

    Benthic communities below the photic zone depend for food on allochthonous organic matter derived from seasonal phytoplankton blooms. In the Baltic Sea, the spring diatom bloom is considered the most important input of organic matter, whereas the contribution of the summer bloom dominated by diazotrophic cyanobacteria is less understood. The possible increase in cyanobacteria blooms as a consequence of eutrophication and climate change calls for evaluation of cyanobacteria effects on benthic community functioning and productivity. Here, we examine utilization of cyanobacterial nitrogen by deposit-feeding benthic macrofauna following a cyanobacteria bloom at three stations during two consecutive years and link these changes to isotopic niche and variations in body condition (assayed as C:N ratio) of the animals. Since nitrogen-fixing cyanobacteria have δ(15)N close to -2‰, we expected the δ(15)N in the deposit-feeders to decrease after the bloom if their assimilation of cyanobacteria-derived nitrogen was substantial. We also expected the settled cyanobacteria with their associated microheterotrophic community and relatively high nitrogen content to increase the isotopic niche area, trophic diversity and dietary divergence between individuals (estimated as the nearest neighbour distance) in the benthic fauna after the bloom. The three surface-feeding species (Monoporeia affinis, Macoma balthica and Marenzelleria arctia) showed significantly lower δ(15)N values after the bloom, while the sub-surface feeder Pontoporeia femorata did not. The effect of the bloom on isotopic niche varied greatly between stations; populations which increased niche area after the bloom had better body condition than populations with reduced niche, regardless of species. Thus, cyanobacterial nitrogen is efficiently integrated into the benthic food webs in the Baltic, with likely consequences for their functioning, secondary production, transfer efficiency, trophic interactions, and

  2. Nitrogen fixed by cyanobacteria is utilized by deposit-feeders.

    Directory of Open Access Journals (Sweden)

    Agnes M L Karlson

    Full Text Available Benthic communities below the photic zone depend for food on allochthonous organic matter derived from seasonal phytoplankton blooms. In the Baltic Sea, the spring diatom bloom is considered the most important input of organic matter, whereas the contribution of the summer bloom dominated by diazotrophic cyanobacteria is less understood. The possible increase in cyanobacteria blooms as a consequence of eutrophication and climate change calls for evaluation of cyanobacteria effects on benthic community functioning and productivity. Here, we examine utilization of cyanobacterial nitrogen by deposit-feeding benthic macrofauna following a cyanobacteria bloom at three stations during two consecutive years and link these changes to isotopic niche and variations in body condition (assayed as C:N ratio of the animals. Since nitrogen-fixing cyanobacteria have δ(15N close to -2‰, we expected the δ(15N in the deposit-feeders to decrease after the bloom if their assimilation of cyanobacteria-derived nitrogen was substantial. We also expected the settled cyanobacteria with their associated microheterotrophic community and relatively high nitrogen content to increase the isotopic niche area, trophic diversity and dietary divergence between individuals (estimated as the nearest neighbour distance in the benthic fauna after the bloom. The three surface-feeding species (Monoporeia affinis, Macoma balthica and Marenzelleria arctia showed significantly lower δ(15N values after the bloom, while the sub-surface feeder Pontoporeia femorata did not. The effect of the bloom on isotopic niche varied greatly between stations; populations which increased niche area after the bloom had better body condition than populations with reduced niche, regardless of species. Thus, cyanobacterial nitrogen is efficiently integrated into the benthic food webs in the Baltic, with likely consequences for their functioning, secondary production, transfer efficiency, trophic

  3. Response of deposit-feeders to exclusion of epibenthic predators in a Mediterranean intertidal flat

    NARCIS (Netherlands)

    Como, S.; Rossi, F.; Lardicci, C.

    2004-01-01

    Deposit-feeders are common components of macrofaunal assemblages in intertidal soft sediments. Predation has been considered to have a central role in affecting their distribution and population dynamics. This study investigates the effect of epibenthic predators on deposit-feeders, inhabiting the

  4. Interactions among contaminant exposure route, kinetics and toxicity in marine deposit-feeders

    DEFF Research Database (Denmark)

    Selck, Henriette

    Many of the chemicals having the greatest likelihood of causing damage in ecological systems, such as polycyclic aromatic hydrocarbons (PAHs) and metals are of persistent and/or hydrophobic character. Deposit-feeders may be important in facilitating the removal of organic contaminants from bulk...

  5. Deposition of carbon nanotubes by a marine suspension feeder revealed by chemical and isotopic tracers

    Energy Technology Data Exchange (ETDEWEB)

    Hanna, Shannon K., E-mail: hanna.shannonk@gmail.com [Bren School of Environmental Science and Management, University of California, Santa Barbara, CA 93106 (United States); Miller, Robert J. [Marine Science Institute, University of California, Santa Barbara, CA 93106 (United States); Lenihan, Hunter S. [Bren School of Environmental Science and Management, University of California, Santa Barbara, CA 93106 (United States)

    2014-08-30

    Highlights: • CNTs decrease the filtration rate of mussels by as much as 24%. • Metals in CNTs and their δ{sup 13}C can be used to quantify CNTs in biological samples. • Mussels exposed to CNTs deposit high concentrations of them in biodeposits. • CNTs accumulate mainly in gut tissue of mussels during exposure. - Abstract: Carbon nanotubes (CNTs) are one of the few truly novel nanomaterials and are being incorporated into a wide range of products, which will lead to environmental release and potential ecological impacts. We examined the toxicity of CNTs to marine mussels and the effect of mussels on CNT fate and transport by exposing mussels to 1, 2, or 3 mg CNTs l{sup −1} for four weeks and measuring mussel clearance rate, shell growth, and CNT accumulation in tissues and deposition in biodeposits. We used metal impurities and carbon stable isotope ratios of the CNTs as tracers of CNT accumulation. Mussels decreased clearance rate of phytoplankton by 24% compared with control animals when exposed to CNTs. However, mussel growth rate was unaffected by CNT concentrations up to 3 mg l{sup −1}. Based on metal concentrations and carbon stable isotope values, mussels deposited most CNTs in biodeposits, which contained >110 mg CNTs g{sup −1} dry weight, and accumulated about 1 mg CNTs g{sup −1} dry weight of tissue. We conclude that extremely high concentrations of CNTs are needed to illicit a toxic response in mussels but the ability of mussels to concentrate and deposit CNTs in feces and pseudofeces may impact infaunal organisms living in and around mussel beds.

  6. Fate and effects of fragrance material on the deposit feeder, Capitella teleta

    DEFF Research Database (Denmark)

    Dai, Lina; Selck, Henriette; Salvito, Daniel

    2010-01-01

    to deposit feeding organisms. Capitella teleta (formerly Capitella sp. I) is a common inhabitant of polluted sediment (e.g., near waste water outlets). The population density of this species is highly organic matter dependent, and more than 400,000 individuals per m2 have been observed in areas with high...... cedrene (AC) was used as a model compound in the present study because of its hydrophobic property and thus the high potential of AC to sorb to particles in the water column and subsequently accumulate in aquatic sediment to a high concentration. Sediment-associated AC may therefore pose a high risk...... organic matter content in the sediment. Therefore, We used 3 worm densities (C. teleta of the same age at 0, 44,000 and 88,000 individuals per m2), sediments with different organic matter content (4% and 2.7%) and AC spiked sediment (0, 50, 100 µg AC/g dw sed), to examine the fate of sediment...

  7. CATTLE FEEDER BEHAVIOR AND FEEDER CATTLE PLACEMENTS

    OpenAIRE

    Kastens, Terry L.; Schroeder, Ted C.

    1994-01-01

    Cattle feeders appear irrational when they place cattle on feed when projected profit is negative. Long futures positions appear to offer superior returns to cattle feeding investment. Cattle feeder behavior suggests that they believe a downward bias in live cattle futures persists and that cattle feeders use different expectations than the live cattle futures market price when making placement decisions. This study examines feeder cattle placement determinants, comparing performance of expec...

  8. Design of apron feeders

    Energy Technology Data Exchange (ETDEWEB)

    Ramos, C.M.

    1987-12-01

    This paper discusses practical aspects of apron feeder design, and includes information on how to make the first selection. Various aspects of design such as feeder speed, material depth, chain-pitch, roller loading, wheels/sprockets and chain roller friction are elaborated in detail. 8 refs., 14 figs., 12 tabs.

  9. Feederism in a woman.

    Science.gov (United States)

    Terry, Lesley L; Vasey, Paul L

    2011-06-01

    Feederism is a fat fetish subculture in which individuals eroticize weight gain and feeding. Feeders are individuals who claim to become sexually aroused by feeding their partners and encouraging them to gain weight. Conversely, Feedees are individuals who claim to become sexually aroused by eating, being fed, and the idea or act of gaining weight. Very little is known about this population. This report describes a woman who self-identified as a Feedee. It is unclear, at present, whether female Feederism represents a unique paraphilia or a thematic variation of morphophilia or sexual masochism.

  10. Dry piston coal feeder

    Science.gov (United States)

    Hathaway, Thomas J.; Bell, Jr., Harold S.

    1979-01-01

    This invention provides a solids feeder for feeding dry coal to a pressurized gasifier at elevated temperatures substantially without losing gas from the gasifier by providing a lock having a double-acting piston that feeds the coals into the gasifier, traps the gas from escaping, and expels the trapped gas back into the gasifier.

  11. Feeder replacement tooling and processes

    International Nuclear Information System (INIS)

    Mallozzi, R.; Goslin, R.; Pink, D.; Askari, A.

    2008-01-01

    Primary heat transport system feeder integrity has become a concern at some CANDU nuclear plants as a result of thinning caused by flow accelerated corrosion (FAC). Feeder inspections are indicating that life-limiting wall thinning can occur in the region between the Grayloc hub weld and second elbow of some outlet feeders. In some cases it has become necessary to replace thinned sections of affected feeders to restore feeder integrity to planned end of life. Atomic Energy of Canada Limited (AECL) and Babcock and Wilcox Canada Ltd. (B and W) have developed a new capability for replacement of single feeders at any location on the reactor face without impacting or interrupting operation of neighbouring feeders. This new capability consists of deploying trained crews with specialized tools and procedures for feeder replacements during planned outages. As may be expected, performing single feeder replacement in the congested working environment of an operational CANDU reactor face involves overcoming many challenges with respect to access to feeders, available clearances for tooling, and tooling operation and performance. This paper describes some of the challenges encountered during single feeder replacements and actions being taken by AECL and B and W to promote continuous improvement of feeder replacement tooling and processes and ensure well-executed outages. (author)

  12. Development of dry coal feeders

    Science.gov (United States)

    Bonin, J. H.; Cantey, D. E.; Daniel, A. D., Jr.; Meyer, J. W.

    1977-01-01

    Design and fabrication of equipment of feed coal into pressurized environments were investigated. Concepts were selected based on feeder system performance and economic projections. These systems include: two approaches using rotating components, a gas or steam driven ejector, and a modified standpipe feeder concept. Results of development testing of critical components, design procedures, and performance prediction techniques are reviewed.

  13. Leaky feeder: the communication backbone

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-01-01

    The need to communicate with all areas of the underground operation in monitoring the movement of men, materials and vehicles, as well as the optimum performance of conveyor systems, has been effectively met with the installation of a Flexcom leaky feeder cable network at a coliery in Mpumalanga. Installed by the South African subsidiary of Mine Radio Systems (MRS), based in Canada, Flexcom is an RF communications highway for underground mines. The system can provide up to 32 voice/data control channels and up to 16 video channels, all operating simultaneously. The system uses a series of bi-directional amplifiers (or signal boosters) spaced at 350 m intervals along the leaky feeder cable, with branching units and termination units added as required. Communication is possible within 50 m of the leaky feeder cable. MRS has 11 conveyors monitored via the SCADA program at the mine and the system produces reports as required which are accessible via cellphone from anywhere in the world. The wireless monitoring of miners and equipment contributes to mine safety. 3 figs.

  14. Non-Selective Evolution of Growing Populations.

    Directory of Open Access Journals (Sweden)

    Karl Wienand

    Full Text Available Non-selective effects, like genetic drift, are an important factor in modern conceptions of evolution, and have been extensively studied for constant population sizes (Kimura, 1955; Otto and Whitlock, 1997. Here, we consider non-selective evolution in the case of growing populations that are of small size and have varying trait compositions (e.g. after a population bottleneck. We find that, in these conditions, populations never fixate to a trait, but tend to a random limit composition, and that the distribution of compositions "freezes" to a steady state. This final state is crucially influenced by the initial conditions. We obtain these findings from a combined theoretical and experimental approach, using multiple mixed subpopulations of two Pseudomonas putida strains in non-selective growth conditions (Matthijs et al, 2009 as model system. The experimental results for the population dynamics match the theoretical predictions based on the Pólya urn model (Eggenberger and Pólya, 1923 for all analyzed parameter regimes. In summary, we show that exponential growth stops genetic drift. This result contrasts with previous theoretical analyses of non-selective evolution (e.g. genetic drift, which investigated how traits spread and eventually take over populations (fixate (Kimura, 1955; Otto and Whitlock, 1997. Moreover, our work highlights how deeply growth influences non-selective evolution, and how it plays a key role in maintaining genetic variability. Consequently, it is of particular importance in life-cycles models (Melbinger et al, 2010; Cremer et al, 2011; Cremer et al, 2012 of periodically shrinking and expanding populations.

  15. in meat production III. Feeder - breeder dimorphism

    African Journals Online (AJOL)

    Feeder- breeder dimorphism is advantageous when large offspring for slaughter is obtained from small breeding animals. The effect of feeder- breeder dimorphism on herd efficiency is evaluated for terminal crossbreeding and growth modification by biotechnological or dietary means. Selection criteria for breeds or lines in ...

  16. An RFID Based Smart Feeder for Hummingbirds.

    Science.gov (United States)

    Ibarra, Vicente; Araya-Salas, Marcelo; Tang, Yu-ping; Park, Charlie; Hyde, Anthony; Wright, Timothy F; Tang, Wei

    2015-12-16

    We present an interdisciplinary effort to record feeding behaviors and control the diet of a hummingbird species (Phaethornis longirostris, the long-billed hermit or LBH) by developing a Radio Frequency Identification (RFID) based smart feeder. The system contains an RFID reader, a microcontroller, and a servo-controlled hummingbird feeder opener; the system is presented as a tool for studying the cognitive ability of the LBH species. When equipped with glass capsule RFID tags (which are mounted on the hummingbird), the smart feeder can provide specific diets for predetermined sets of hummingbirds at the discretion of biologists. This is done by reading the unique RFID tag on the hummingbirds and comparing the ID number with the pre-programmed ID numbers stored in the smart feeder. The smart feeder records the time and ID of each hummingbird visit. The system data is stored in a readily available SD card and is powered by two 9 V batteries. The detection range of the system is approximately 9-11 cm. Using this system, biologists can assign the wild hummingbirds to different experimental groups and monitor their diets to determine if they develop a preference to any of the available nectars. During field testing, the smart feeder system has demonstrated consistent detection (when compared to detections observed by video-recordings) of RFID tags on hummingbirds and provides pre-designed nectars varying water and sugar concentrations to target individuals. The smart feeder can be applied to other biological and environmental studies in the future.

  17. Adhesion of non-selective CVD tungsten to silicon dioxide

    International Nuclear Information System (INIS)

    Woodruff, D.W.; Wilson, R.H.; Sanchez-Martinez, R.A.

    1986-01-01

    Adhesion of non-selective, CVD tungsten to silicon dioxide is a critical issue in the development of tungsten as a metalization for VLSI circuitry. Without special adhesion promoters, tungsten deposited from WF/sub 6/ and H/sub 2/ has typically failed a standard tape test over all types of silicon oxides and nitrides. The reasons for failure of thin films, and CVD tungsten in particular are explored along with standard techniques for improving adhesion of thin films. Experiments are reported which include a number of sputtered metals as adhesion promoters, as well as chemical and plasma treatment of the oxide surface. Sputtered molybdenum is clearly the superior adhesion promoting layer from these tests. Traditional adhesion layers such as chromium or titanium failed as adhesion layers for CVD tungsten possibly due to chemical reactions between the WF/sub 6/ and Cr or Ti

  18. A study of inter linkage effects on Candu feeder piping

    International Nuclear Information System (INIS)

    Li, M.; Aggarwal, M.L.; Meysner, A.

    2005-01-01

    A CANDU (Canadian Deuterium Uranium) reactor core consists of a large number of fuel channels where heat is generated. Two feeder pipes are connected to each fuel channel to transport D 2 O coolant into and out of the reactor core. The feeder piping is designed to the requirements of Class 1 piping of Section III NB of the ASME Boiler and Pressure Vessel and CSA Codes. Feeder piping stress analysis is being performed to demonstrate the code compliance check and the fitness for service of feeders. In the past, stress analyses were conducted for each individual feeder without including interaction effects among connected feeders. Interaction effects occur as a result of linkages that exist between feeders to prevent fretting and impacting damage during normal, abnormal and accident conditions. In this paper, a 'combined' approach is adopted to include all feeders connected by inter linkages into one feeder piping model. MSC/NASTRAN finite element software was used in the stress simulation, which contains up to 127 feeder pipes. The ASME Class 1 piping analysis was conducted to investigate the effects of the linkages between feeders. Both seismic time history and broadened response spectra methods were used in the seismic stress calculation. The results show that the effect of linkages is significant in dynamic stresses for all feeder configurations, as well as in static stresses for certain feeder configurations. The single feeder analysis could either underestimate or overestimate feeder stresses depending on the pipe geometry and bend wall thickness. (authors)

  19. An RFID Based Smart Feeder for Hummingbirds

    Directory of Open Access Journals (Sweden)

    Vicente Ibarra

    2015-12-01

    Full Text Available We present an interdisciplinary effort to record feeding behaviors and control the diet of a hummingbird species (Phaethornis longirostris, the long-billed hermit or LBH by developing a Radio Frequency Identification (RFID based smart feeder. The system contains an RFID reader, a microcontroller, and a servo-controlled hummingbird feeder opener; the system is presented as a tool for studying the cognitive ability of the LBH species. When equipped with glass capsule RFID tags (which are mounted on the hummingbird, the smart feeder can provide specific diets for predetermined sets of hummingbirds at the discretion of biologists. This is done by reading the unique RFID tag on the hummingbirds and comparing the ID number with the pre-programmed ID numbers stored in the smart feeder. The smart feeder records the time and ID of each hummingbird visit. The system data is stored in a readily available SD card and is powered by two 9 V batteries. The detection range of the system is approximately 9–11 cm. Using this system, biologists can assign the wild hummingbirds to different experimental groups and monitor their diets to determine if they develop a preference to any of the available nectars. During field testing, the smart feeder system has demonstrated consistent detection (when compared to detections observed by video-recordings of RFID tags on hummingbirds and provides pre-designed nectars varying water and sugar concentrations to target individuals. The smart feeder can be applied to other biological and environmental studies in the future.

  20. Economic feeder for recharging and ``topping off''

    Science.gov (United States)

    Fickett, Bryan; Mihalik, G.

    2000-04-01

    Increasing the size of the melt charge significantly increases yield and reduces costs. Siemens Solar Industries is optimizing a method to charge additional material after meltdown (top-off) using an external feeder system. A prototype feeder system was fabricated consisting of a hopper and feed delivery system. The low-cost feeder is designed for simple operation and maintenance. The system is capable of introducing up to 60 kg of granular silicon while under vacuum. An isolation valve permits refilling of the hopper while maintaining vacuum in the growth furnace. Using the feeder system in conjunction with Siemens Solar Industries' energy efficient hot zone dramatically reduces power and argon consumption. Throughput is also improved as faster pull speeds can be attained. The increased pull speeds have an even greater impact when the charge size is increased. Further cost reduction can be achieved by refilling the crucible after crystal growth and pulling a second ingot run. Siemens Solar Industries is presently testing the feeder in production.

  1. Advances in technologies for feeder pipe inspections

    Energy Technology Data Exchange (ETDEWEB)

    Ten Grotenhuis, R.; Verma, Y.; Hitchcox, T.; Sakuta, A. [Ontario Power Generation, Inspection and Maintenance Div., Toronto, Ontario (Canada)

    2014-07-15

    The successful development of the Matrix Inspection Technique (MIT) for feeder weld area applications has been followed up with a project to leverage the technology to address other aspects of feeder inspection. The goal of the project is to adapt the technology to provide full circumferential inspection of feeder pipes for FAC thinning and, potentially, for axial cracking. The project necessitated evolving a new generation of high speed, high element count data acquisition instruments. It also required the development of custom inspection arrays, innovative approaches to sealing the water column, use of inertial motion sensors to synthesize encoder inputs, real-time visual feedback for the operator, and enhanced automated analysis software capable of plotting the inspected configuration in 3D. The individual components of the system are currently being integrated into a whole. The results obtained to date demonstrate the approach to be fundamentally sound. (author)

  2. Vertical-Screw-Auger Conveyer Feeder

    Science.gov (United States)

    Walton, Otis (Inventor); Vollmer, Hubert J. (Inventor)

    2016-01-01

    A conical feeder is attached to a vertically conveying screw auger. The feeder is equipped with scoops and rotated from the surface to force-feed regolith the auger. Additional scoops are possible by adding a cylindrical section above the conical funnel section. Such then allows the unit to collect material from swaths larger in diameter than the enclosing casing pipe of the screw auger. A third element includes a flexible screw auger. All three can be used in combination in microgravity and zero atmosphere environments to drill and recover a wide area of subsurface regolith and entrained volatiles through a single access point on the surface.

  3. Counseling in the Elementary Feeder Schools.

    Science.gov (United States)

    Dunham, Virginia

    This brief paper presents the concept of transition counseling between a junior high school and its feeder school(s), designed to make the change from elementary into junior high less traumatic. Aside from routine sixth grade counseling, the counselors expanded their base of counseling to include all types of problems as well as all grade levels.…

  4. The development and manufacture of size for size feeder pipe for feeder replacement

    International Nuclear Information System (INIS)

    Legate, G.; Schreiter, D.; Townley, N.

    2008-01-01

    The recently recognised problem of feeder pipe thinning created a unique sourcing problem. Operators require relatively small quantities of nuclear class 1 seamless feeder pipe for such replacement which prior to the introduction of this product in 2006 was not available. It was desired that the pipe be produced at the exact size of the pipe currently in use at the specific reactor site (feeder pipe size varies from site to site). Secondly the pipe had to be made in conformance to the original code year of issue and to conform to the intent of the original material specifications. Finally a supply strategy had to be implemented allowing for timely manufacture of replacement piping. This presentation will report upon how replacement size for size feeder tube was developed and is currently manufactured at Nu-Tech Precision Metals. The paper will also detail the current supply strategy to ensure timely manufacture of the product.

  5. Expectations of Cattle Feeding Investors in Feeder Cattle Placements

    OpenAIRE

    Kastens, Terry L.; Schroeder, Ted C.

    1993-01-01

    Cattle feeders appear irrational when they place cattle on feed when projected profits are negative. Long futures positions appear to offer superior returns to cattle feeding investment. Cattle feeder behavior suggests that they believe a downward bias in live cattle futures persists and that cattle feeders use different information than the live cattle futures market price when making placement decisions. This paper examines feeder cattle placement determinants and compares performance of ex...

  6. A bend thickness sensitivity study of Candu feeder piping

    International Nuclear Information System (INIS)

    Li, M.; Aggarwal, M.L.; Meysner, A.; Micelotta, C.

    2005-01-01

    In CANDU reactors, feeder bends close to the connection at the fuel channel may be subjected to the highest Flow Accelerated Corrosion (FAC) and stresses. Feeder pipe stress analysis is crucial in the life extension of aging CANDU plants. Typical feeder pipes are interconnected by upper link plates and spacers. It is well known that the stresses at the bends are sensitive to the local bend thicknesses. It is also known from the authors' study (Li and et al, 2005) that feeder inter linkage effect is significant and cannot be ignored. The field measurement of feeder bend thickness is difficult and may be subjected to uncertainty in accuracy. Hence, it is desirable to know how the stress on a subject feeder could be affected by the bend thickness variation of the neighboring feeders. This effect cannot be evaluated by the traditional 'single' feeder model approach. In this paper, the 'row' and 'combined' models developed in the previous study (Li and et al, 2005), which include the feeder interactions, are used to investigate the sensitivity of bend thickness. A series of random thickness bounded by maximum and minimum measured values were applied to feeders in the model. The results show that an individual feeder is not sensitive to the bend thickness variation of the remaining feeders in the model, but depends primarily on its own bend thickness. The highest stress at a feeder always occurs when the feeder has the smallest possible bend thickness. A minimum acceptable bend thickness for individual feeders can be computed by an iterative computing process. The dependency of field thickness measurement and the amount of required analysis work can be greatly reduced. (authors)

  7. Pressurized feeder for biofuels; Paineistettu syoetin biopolttoaineille

    Energy Technology Data Exchange (ETDEWEB)

    Lundqvist, R; Makkonen, P [Foster Wheeler Energia Oy, Karhula (Finland). Karhula R and D Center

    1996-12-31

    A new type of pressurized piston feeder has been tested for further development of the IGCC concept. The project is funded by the Finnish Ministry of Trade and Industry. The objective has been to develop a substitute for lock-hopper systems, which are commercial, but far too expensive from an operational point of view, due to high inert gas consumption for pressurization. The new feeder system, which is of dual piston type, uses little inert gas, because the pressurization sequence is performed partially by the piston movement. The project comprised further development of the concept, mechanical testing under atmospheric and pressurized conditions and testing with wood chips, peat and coal at elevated pressures. The main concern has been the wear of seals and gaskets during long term operation and for this reason over 600 hours of testing has been carried out. The tests were carried out between May 1994 and January 1995 with wood chips, peat and coal mainly at 17 bar(a) pressure. During the operation, the system was fine-tuned, and generally, the testing was successful. At the early stage of the tests, the ring seal design was modified and several alternative seal constructions were tested. During the tests, the seal was developed further and improved. The present ring seal design has been proven reliable and it meets the commercial requirements. After the tests, the feeder system was inspected thoroughly and found to be in good condition. A commercially available concept of the feeder has been developed on the basis of the knowledge obtained during the test runs

  8. Pressurized feeder for biofuels; Paineistettu syoetin biopolttoaineille

    Energy Technology Data Exchange (ETDEWEB)

    Lundqvist, R.; Makkonen, P. [Foster Wheeler Energia Oy, Karhula (Finland). Karhula R and D Center

    1995-12-31

    A new type of pressurized piston feeder has been tested for further development of the IGCC concept. The project is funded by the Finnish Ministry of Trade and Industry. The objective has been to develop a substitute for lock-hopper systems, which are commercial, but far too expensive from an operational point of view, due to high inert gas consumption for pressurization. The new feeder system, which is of dual piston type, uses little inert gas, because the pressurization sequence is performed partially by the piston movement. The project comprised further development of the concept, mechanical testing under atmospheric and pressurized conditions and testing with wood chips, peat and coal at elevated pressures. The main concern has been the wear of seals and gaskets during long term operation and for this reason over 600 hours of testing has been carried out. The tests were carried out between May 1994 and January 1995 with wood chips, peat and coal mainly at 17 bar(a) pressure. During the operation, the system was fine-tuned, and generally, the testing was successful. At the early stage of the tests, the ring seal design was modified and several alternative seal constructions were tested. During the tests, the seal was developed further and improved. The present ring seal design has been proven reliable and it meets the commercial requirements. After the tests, the feeder system was inspected thoroughly and found to be in good condition. A commercially available concept of the feeder has been developed on the basis of the knowledge obtained during the test runs

  9. Improvement of automatic fish feeder machine design

    Science.gov (United States)

    Chui Wei, How; Salleh, S. M.; Ezree, Abdullah Mohd; Zaman, I.; Hatta, M. H.; Zain, B. A. Md; Mahzan, S.; Rahman, M. N. A.; Mahmud, W. A. W.

    2017-10-01

    Nation Plan of action for management of fishing is target to achieve an efficient, equitable and transparent management of fishing capacity in marine capture fisheries by 2018. However, several factors influence the fishery production and efficiency of marine system such as automatic fish feeder machine could be taken in consideration. Two latest fish feeder machines have been chosen as the reference for this study. Based on the observation, it has found that the both machine was made with heavy structure, low water and temperature resistance materials. This research’s objective is to develop the automatic feeder machine to increase the efficiency of fish feeding. The experiment has conducted to testing the new design of machine. The new machine with maximum storage of 5 kg and functioning with two DC motors. This machine able to distribute 500 grams of pellets within 90 seconds and longest distance of 4.7 meter. The higher speed could reduce time needed and increase the distance as well. The minimum speed range for both motor is 110 and 120 with same full speed range of 255.

  10. Feeder density enhances house finch disease transmission in experimental epidemics.

    Science.gov (United States)

    Moyers, Sahnzi C; Adelman, James S; Farine, Damien R; Thomason, Courtney A; Hawley, Dana M

    2018-05-05

    Anthropogenic food provisioning of wildlife can alter the frequency of contacts among hosts and between hosts and environmental sources of pathogens. Despite the popularity of garden bird feeding, few studies have addressed how feeders influence host contact rates and disease dynamics. We experimentally manipulated feeder density in replicate aviaries containing captive, pathogen-naive, groups of house finches ( Haemorhous mexicanus ) and continuously tracked behaviours at feeders using radio-frequency identification devices. We then inoculated one bird per group with Mycoplasma gallisepticum (Mg), a common bacterial pathogen for which feeders are fomites of transmission, and assessed effects of feeder density on house finch behaviour and pathogen transmission. We found that pathogen transmission was significantly higher in groups with the highest density of bird feeders, despite a significantly lower rate of intraspecific aggressive interactions relative to the low feeder density groups. Conversely, among naive group members that never showed signs of disease, we saw significantly higher concentrations of Mg-specific antibodies in low feeder density groups, suggesting that birds in low feeder density treatments had exposure to subclinical doses of Mg. We discuss ways in which the density of garden bird feeders could play an important role in mediating the intensity of Mg epidemics.This article is part of the theme issue 'Anthropogenic resource subsidies and host-parasite dynamics in wildlife'. © 2018 The Author(s).

  11. Impact of flow accelerated corrosion (FAC) on feeder refurbishment planning

    International Nuclear Information System (INIS)

    Jyrkama, M.; Pandey, M.

    2010-01-01

    Feeder wall thinning due to flow accelerated corrosion (FAC) may result in a large number of feeder replacements in the future. In this study, the process of FAC is modelled using a probabilistic approach and used to predict the expected number of degraded feeders and their replacements in the future. Because of the high cost associated with feeder replacements, it may be optimal to replace the entire feeder population during a single refurbishment outage when the unit cost of replacement is likely to be less. The results of this study demonstrate, however, that the unit cost of feeder replacement must be sufficiently lower than the standard replacement cost and the refurbishment performed at an optimal time to realize the economic benefits associated with the refurbishment. (author)

  12. A HYBRID APPROACH FOR RURAL FEEDER DESIGN

    Directory of Open Access Journals (Sweden)

    DAMANJEET KAUR

    2012-08-01

    Full Text Available In this paper, a population based approach for conductor size selection in rural radial distribution system is presented. The proposed hybrid approach implies a particle swarm optimization (PSO approach in combination with mutant property of differential evolution (DE for conductor size selection in radial distribution system. The conductor size for each feeder segment is selected such that the total cost of capital investment and capitalized cost of energy losses is minimized while constraints of voltage at each node and current carrying capacity of conductor is within the limits. The applicability and effectiveness of the proposed method is demonstrated with the help of 32-node test system.

  13. Risk-informed prediction of feeder end of life

    International Nuclear Information System (INIS)

    Jyrkama, M.; Pandey, M.

    2011-01-01

    The operating life of feeder piping is negatively impacted by flow accelerated corrosion (FAC). In this study, an assessment of a large set of inspection data reveals that FAC in feeders is a relatively stationary process, with variability only at the local scale. Given the added uncertainty from inspection coverage, a new method for estimating the thinning rate and feeder EOL is developed using a probabilistic approach. The results of the study illustrate the benefits of the methodology in supporting risk-informed decision making at the station by quantifying the present and incremental risk in the feeder system over time. (author)

  14. Determination of representative CANDU feeder dimensions for engineering simulator

    International Nuclear Information System (INIS)

    Cho, S.; Muzumdar, A.

    1996-01-01

    This paper describes a logic for selection of representative channel groups and a methodology for determination of representative CANDU feeder dimensions and the pressure drops between inlet/outlet header and fuel channel in the primary loop. A code, MEDOC, was developed based on this logic and methodology and helps perform a calculation of representative feeder dimensions for a selected channel group on the basis of feeder geometry data (fluid volume, mass flow rate, loss factor) and given property data (pressure, quality, density) at inlet/outlet header. The representative feeder dimensions calculated based on this methodology will be useful for the engineering simulator for the CANDU type reactor. (author)

  15. Risk-informed prediction of feeder end of life

    Energy Technology Data Exchange (ETDEWEB)

    Jyrkama, M.; Pandey, M. [Univ. of Waterloo, Ontario (Canada)

    2011-07-01

    The operating life of feeder piping is negatively impacted by flow accelerated corrosion (FAC). In this study, an assessment of a large set of inspection data reveals that FAC in feeders is a relatively stationary process, with variability only at the local scale. Given the added uncertainty from inspection coverage, a new method for estimating the thinning rate and feeder EOL is developed using a probabilistic approach. The results of the study illustrate the benefits of the methodology in supporting risk-informed decision making at the station by quantifying the present and incremental risk in the feeder system over time. (author)

  16. Comparative Study Of Two Non-Selective Cyclooxygenase ...

    African Journals Online (AJOL)

    The comparative study of the effects of two non-selective cyclooxygenase inhibitors ibuprofen and paracetamol on maternal and neonatal growth was conducted using 15 Sprague dawley rats, with mean body weight ranging between 165 and 179g. The rats were separated at random into three groups (A, B and C).

  17. 26 CFR 1.502-1 - Feeder organizations.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 7 2010-04-01 2010-04-01 true Feeder organizations. 1.502-1 Section 1.502-1...) INCOME TAXES (CONTINUED) Exempt Organizations § 1.502-1 Feeder organizations. (a) In the case of an organization operated for the primary purpose of carrying on a trade or business for profit, exemption is not...

  18. Colour preferences of UK garden birds at supplementary seed feeders.

    Directory of Open Access Journals (Sweden)

    Luke Rothery

    Full Text Available Supplementary feeding of garden birds generally has benefits for both bird populations and human wellbeing. Birds have excellent colour vision, and show preferences for food items of particular colours, but research into colour preferences associated with artificial feeders is limited to hummingbirds. Here, we investigated the colour preferences of common UK garden birds foraging at seed-dispensing artificial feeders containing identical food. We presented birds simultaneously with an array of eight differently coloured feeders, and recorded the number of visits made to each colour over 370 30-minute observation periods in the winter of 2014/15. In addition, we surveyed visitors to a garden centre and science festival to determine the colour preferences of likely purchasers of seed feeders. Our results suggest that silver and green feeders were visited by higher numbers of individuals of several common garden bird species, while red and yellow feeders received fewer visits. In contrast, people preferred red, yellow, blue and green feeders. We suggest that green feeders may be simultaneously marketable and attractive to foraging birds.

  19. Development of ceramic-free antenna feeder

    International Nuclear Information System (INIS)

    Moriyama, S.; Kimura, H.; Fujii, T.; Saigusa, M.; Arai, H.

    1994-01-01

    We have proposed a ceramics-free antenna feeder line employing a ridged waveguide as a local support for IC antenna of next-generation tokamaks. One fourth mock-up model of the all metal waveguide designed for the ITER ICRF system is fabricated and electrical characteristics of the model including the coaxial line - waveguide converter are measured. Power reflection coefficient of the model including the coax-waveguide converter to the input coaxial line is estimated to be less than 15% below the cut-off frequency of 107 MHz and less than 3% above the cut-off frequency. It is found that this ceramics-free antenna support employing a ridged waveguide is quite available for IC antenna of next-generation tokamaks. (author)

  20. A Dynamic and Heuristic Phase Balancing Method for LV Feeders

    Directory of Open Access Journals (Sweden)

    Samad Taghipour Boroujeni

    2016-01-01

    Full Text Available Due to the single-phase loads and their stochastic behavior, the current in the distribution feeders is not balanced. In addition, the single-phase loads are located in different positions along the LV feeders. So the amount of the unbalanced load and its location affect the feeder losses. An unbalanced load causes the feeder losses and the voltage drop. Because of time-varying behavior of the single-phase loads, phase balancing is a dynamic and combinatorial problem. In this research, a heuristic and dynamic solution for the phase balancing of the LV feeders is proposed. In this method, it is supposed that the loads’ tie could be connected to all phases through a three-phase switch. The aim of the proposed method is to make the feeder conditions as balanced as possible. The amount and the location of single-phase loads are considered in the proposed phase balancing method. Since the proposed method needs no communication interface or no remote controller, it is inexpensive, simple, practical, and robust. Applying this method provides a distributed and dynamic phase balancing control. In addition, the feasibility of reducing the used switches is investigated. The ability of the proposed method in the phase balancing of the LV feeders is approved by carrying out some simulations.

  1. Human induced pluripotent stem cells on autologous feeders.

    Directory of Open Access Journals (Sweden)

    Kazutoshi Takahashi

    Full Text Available BACKGROUND: For therapeutic usage of induced Pluripotent Stem (iPS cells, to accomplish xeno-free culture is critical. Previous reports have shown that human embryonic stem (ES cells can be maintained in feeder-free condition. However, absence of feeder cells can be a hostile environment for pluripotent cells and often results in karyotype abnormalities. Instead of animal feeders, human fibroblasts can be used as feeder cells of human ES cells. However, one still has to be concerned about the existence of unidentified pathogens, such as viruses and prions in these non-autologous feeders. METHODOLOGY/PRINCIPAL FINDINGS: This report demonstrates that human induced Pluripotent Stem (iPS cells can be established and maintained on isogenic parental feeder cells. We tested four independent human skin fibroblasts for the potential to maintain self-renewal of iPS cells. All the fibroblasts tested, as well as their conditioned medium, were capable of maintaining the undifferentiated state and normal karyotypes of iPS cells. Furthermore, human iPS cells can be generated on isogenic parental fibroblasts as feeders. These iPS cells carried on proliferation over 19 passages with undifferentiated morphologies. They expressed undifferentiated pluripotent cell markers, and could differentiate into all three germ layers via embryoid body and teratoma formation. CONCLUSIONS/SIGNIFICANCE: These results suggest that autologous fibroblasts can be not only a source for iPS cells but also be feeder layers. Our results provide a possibility to solve the dilemma by using isogenic fibroblasts as feeder layers of iPS cells. This is an important step toward the establishment of clinical grade iPS cells.

  2. A Decentralized Storage Strategy for Residential Feeders with Photovoltaics

    DEFF Research Database (Denmark)

    Marra, Francesco; Yang, Guangya; Træholt, Chresten

    2014-01-01

    . The power sizing of the ESSs is performed with linear programming (LP) method, based on voltage sensitivity analysis. A Belgian residential LV feeder with private PV systems is used as a case study to demonstrate the effectiveness of the proposed strategy. Quantification of the required energy levels...... domestic energy storage systems (ESS). The traditional way of operating a domestic ESS to increase the local consumption rate does not take into account the need of voltage support in a feeder; the proposed storage concept improves the traditional one, by mitigating voltage rise due to PV in the feeder...

  3. Automation Selection and Sequencing of Traps for Vibratory Feeders

    DEFF Research Database (Denmark)

    Mathiesen, Simon; Ellekilde, Lars-Peter

    2017-01-01

    Vibratory parts feeders with mechanical orienting devices are used extensively in the assembly automation industry. Even so, the design process is based on trial-and-error approaches and is largely manual. In this paper, a methodology is presented for automatic design of this type of feeder....... The approach uses dynamic simulation for generating the necessary data for configuring a feeder with a sequence of mechanical orienting devices called traps, with the goal of reorienting all parts from a random to fixed orientation. Then, a fast algorithm for facilitating this configuration task automatically...

  4. Damping considerations in CANDU feeder pipe design and analysis

    International Nuclear Information System (INIS)

    Usmani, S.A.; Saleem, M.A.; So, G.

    1990-01-01

    Recent developments in pipe damping indicate a trend towards more realistic and less conservative values, which result in less rigid and safer pipe designs. The CANDU-PHW (Canada deuterium uranium, pressurized heavy water) reactor feeder pipe designs have applied similar approaches which permit seismic qualifications without overly restraining these compact arrays of pipes to cater for the large creep and thermal anchor movement. This paper reviews the feeder design aspects, especially pertaining to the design provisions, experimental verification and analytical modelling for seismic qualification in the light of recent pipe dynamic developments. Using illustrative examples, comparison of seismic analysis results is provided for the ASME Code Case N-411 dampings, and those traditionally used in the feeder seismic qualification. The results confirm acceptability of the traditional approach which permit simplified analysis to demonstrate seismic qualificationqualification of CANDU feeder pipes

  5. Faecal nitrogen of browser and mixed feeder game species during ...

    African Journals Online (AJOL)

    Faecal nitrogen of browser and mixed feeder game species during different seasons. ... A practical measure of assessing periods of potential nutritional stress of game species is needed in the management of ... AJOL African Journals Online.

  6. Structural integrity investigations of feeder pipe ice plugging procedures

    International Nuclear Information System (INIS)

    Flaman, M.T.; Shah, N.N.

    1985-03-01

    A procedure involving the use of a liquid nitrogen cooled heat exchanger to form internal ice plugs in feeder pipes is routinely used in nuclear generating stations. The use of this procedure has caused concerns with regard to the safety of station maintenance personnel, and in regard to the integrity of the feeder pipes. This report describes the results of laboratory stress and pressure measurements which were performed on a feeder pipe section during ice plugging operations to investigate these concerns. From the results of this study, and from the results of previous studies of material behaviour at low temperatures, it has been determined that the ice plugging procedure can be performed on feeder pipes in a safe and effective manner

  7. SAFIRE - a robotic inspection system for CANDU feeders

    International Nuclear Information System (INIS)

    Buckingham, R.

    2011-01-01

    The condition of primary circuit feeder pipes in CANDU reactors is relevant to the commercial viability and plant life. One known wear mechanism is external fretting between feeder pipes and adjacent services or support structures, particularly within the Upper Feeder Cabinet (UFC). Fretting leads to wall thinning which must not exceed certain agreed limits. Chafe shields have been added to protect the feeder pipes. Regular inspections are required of the chafe shields, feeder pipes and other structures that may cause feeder damage. Historically, the dose received by inspectors conducting this work has been significant. For this reason Ontario Power Generation has invested in a remotely operated robot system to conduct visual inspections within the UFC. This system, called SAFIRE for 'Snake-Arm Feeder Inspection Robot Equipment' has been deployed at Pickering during 2010 and 2011 and has been used to inspect areas that are extremely difficult to inspect with existing manual techniques. The 2011 scope of work included inspection of a total of 660 feeder pipes in three UFC quadrants, in two reactors. The full scope was completed over a one-month period in Autumn 2011 in which SAFIRE was used during 23, twelve hour shifts. This included two periods each of 72 hours of continuous operation using multiple teams of operators. SAFIRE is remote controlled delivery system for multiple cameras to record still images and video. The main system elements include a snake-arm robot mounted on a mobile vehicle. It can be controlled from up to 500m away using a fibre/copper connection. The snake-arm is 2.2m long, 25mm wide and has 18 degrees of freedom. It is designed to snake between the rows of feeder pipes to inspect feeder/hanger interfaces, both above and below the feeder cabinet catwalks. Future upgrades offer the potential to add additional tools to increase functionality. This paper describes the SAFIRE development process from inception to operational experience gained

  8. SAFIRE - a robotic inspection system for CANDU feeders

    Energy Technology Data Exchange (ETDEWEB)

    Buckingham, R. [OC Robotics, Bristol (United Kingdom)

    2011-07-01

    The condition of primary circuit feeder pipes in CANDU reactors is relevant to the commercial viability and plant life. One known wear mechanism is external fretting between feeder pipes and adjacent services or support structures, particularly within the Upper Feeder Cabinet (UFC). Fretting leads to wall thinning which must not exceed certain agreed limits. Chafe shields have been added to protect the feeder pipes. Regular inspections are required of the chafe shields, feeder pipes and other structures that may cause feeder damage. Historically, the dose received by inspectors conducting this work has been significant. For this reason Ontario Power Generation has invested in a remotely operated robot system to conduct visual inspections within the UFC. This system, called SAFIRE for 'Snake-Arm Feeder Inspection Robot Equipment' has been deployed at Pickering during 2010 and 2011 and has been used to inspect areas that are extremely difficult to inspect with existing manual techniques. The 2011 scope of work included inspection of a total of 660 feeder pipes in three UFC quadrants, in two reactors. The full scope was completed over a one-month period in Autumn 2011 in which SAFIRE was used during 23, twelve hour shifts. This included two periods each of 72 hours of continuous operation using multiple teams of operators. SAFIRE is remote controlled delivery system for multiple cameras to record still images and video. The main system elements include a snake-arm robot mounted on a mobile vehicle. It can be controlled from up to 500m away using a fibre/copper connection. The snake-arm is 2.2m long, 25mm wide and has 18 degrees of freedom. It is designed to snake between the rows of feeder pipes to inspect feeder/hanger interfaces, both above and below the feeder cabinet catwalks. Future upgrades offer the potential to add additional tools to increase functionality. This paper describes the SAFIRE development process from inception to operational experience

  9. Urban Bird Feeders Dominated by a Few Species and Individuals

    Directory of Open Access Journals (Sweden)

    Josie A. Galbraith

    2017-08-01

    Full Text Available The practice of garden bird feeding is a global phenomenon, involving millions of people and vast quantities of food annually. Many people engage in the practice of feeding assuming that birds gain some benefit from the food they provide, yet recent studies have revealed the potential for detrimental impacts as well. However, there is still a paucity of information on the impacts of feeding, including the ubiquity of these impacts among and within feeder-visiting species. Consistency in feeder use among birds is likely an important determinant of this. Individual birds and species that make frequent use of feeders are more likely to experience both the benefits and detrimental impacts of supplementary food. We investigated patterns of feeder use by garden birds visiting experimental feeding stations in Auckland, New Zealand, with the specific aim of determining whether use of supplementary food was consistent or variable among individuals and species. We used camera traps as well as Radio Frequency Identification (RFID technology to examine intra- and interspecific feeder visitation patterns and to discern species associations. Eleven bird species were detected using feeding stations, however, two introduced species (house sparrow Passer domesticus and spotted dove Streptopelia chinensis dominated visitation events. These species were present at feeders most frequently, with the largest conspecific group sizes. Significant associations were detected among a number of species, suggesting interspecific interactions are important in determining feeder use. We also found within-species differences in feeder use for all focal species, with individual variation greatest in house sparrows. Furthermore, season had an important influence on most visitation parameters. The observed individual and species-specific differences in supplementary food resource use imply that the impacts of garden bird feeding are not universal. Crucially, particularly given

  10. Neural stem cells achieve and maintain pluripotency without feeder cells.

    Directory of Open Access Journals (Sweden)

    Hyun Woo Choi

    Full Text Available BACKGROUND: Differentiated cells can be reprogrammed into pluripotency by transduction of four defined transcription factors. Induced pluripotent stem cells (iPS cells are expected to be useful for regenerative medicine as well as basic research. Recently, the report showed that mouse embryonic fibroblasts (MEF cells are not essential for reprogramming. However, in using fibroblasts as donor cells for reprogramming, individual fibroblasts that had failed to reprogram could function as feeder cells. METHODOLOGY/PRINCIPAL FINDING: Here, we show that adult mouse neural stem cells (NSCs, which are not functional feeder cells, can be reprogrammed into iPS cells using defined four factors (Oct4, Sox2, Klf4, and c-Myc under feeder-free conditions. The iPS cells, generated from NSCs expressing the Oct4-GFP reporter gene, could proliferate for more than two months (passage 20. Generated and maintained without feeder cells, these iPS cells expressed pluripotency markers (Oct4 and Nanog, the promoter regions of Oct4 and Nanog were hypomethylated, could differentiated into to all three germ layers in vitro, and formed a germline chimera. These data indicate that NSCs can achieve and maintain pluripotency under feeder-free conditions. CONCLUSION/SIGNIFICANCE: This study suggested that factors secreted by feeder cells are not essential in the initial/early stages of reprogramming and for pluripotency maintenance. This technology might be useful for a human system, as a feeder-free reprogramming system may help generate iPS cells of a clinical grade for tissue or organ regeneration.

  11. Assessment of CANDU feeders subject to flow accelerated corrosion

    Energy Technology Data Exchange (ETDEWEB)

    Iyer, S. [Atomic Energy of Canada Ltd., Mississauga, Ontario (Canada); Slade, J.P. [New Brunswick Power, Point Lepreau Generating Station, Lepreau, New Brunswick (Canada)

    2003-07-01

    'Full Text:' Inspections of CANDU feeders have indicated greater than expected wall thinning of outlet feeders. This wall thinning is attributed to Flow-Accelerated Corrosion (FAC). The rate of wall loss due to FAC is highest in the close radius bends near the end fitting. The minimum allowed thickness for a feeder pipes is based on design pressure during the design stage. Extended operation of the thinned feeders beyond their design basis, i.e., operation of feeders with thickness below design pressure based minimum thickness has economic benefits for the utilities. In such cases, it is important to establish the remaining life and evaluate the adequacy of the components for safe operation. ASME Code Case N-597 provides the guidelines for acceptance for continued service of Classes 2 and 3 piping components experiencing wall thinning during operation. However, for Class 1 systems, the Code Case recommends that the owner develop the methodology and criteria for the assessment of wall thinning. Therefore, under the CANDU Owner's Group's (COG) Feeder Integrity Joint Program (FIJP), the 'Fitness for Service Guidelines (FFSG) for Feeders Affected by Wall Thinning in Operating CANDU Reactors' was developed and subsequently conditionally approved by CNSC. This paper illustrates the underlying concepts in the FFSG methodology and its benefits to utilities. Specific examples of the application and benefits of the FFSG at Point Lepreau G.S. are described in this paper. The assessment of feeders is based on the requirements of the construction Code (Section III of the ASME Boiler and Pressure Vessel Code): The following points briefly describe the assessment methodology. Satisfying the requirements of NB-3650 for design and service loadings are sufficient for continued service and extended life if the predicted minimum wall thickness of the component is greater than or equal to 90% of the pressure based thickness calculated as per NB-3641. The B

  12. Object categorization by wild ranging birds-Winter feeder experiments.

    Science.gov (United States)

    Nováková, Nela; Veselý, Petr; Fuchs, Roman

    2017-10-01

    The object categorization is only scarcely studied using untrained wild ranging animals and relevant stimuli. We tested the importance of the spatial position of features salient for categorization of a predator using wild ranging birds (titmice) visiting a winter feeder. As a relevant stimulus we used a dummy of a raptor, the European sparrowhawk (Accipiter nisus), placed at the feeding location. This dummy was designed to be dismantled into three parts and rearranged with the head in the correct position, in the middle or at the bottom of the dummy. When the birds had the option of visiting an alternative feeder with a dummy pigeon, they preferred this option to visiting the feeder with the dummy sparrowhawk with the head in any of the three positions. When the birds had the option of visiting an alternative feeder with an un-rearranged dummy sparrowhawk, they visited both feeders equally often, and very scarcely. This suggests that the titmice considered all of the sparrowhawk modifications as being dangerous, and equally dangerous as the un-rearranged sparrowhawk. The position of the head was not the most important cue for categorization. The presence of the key features was probably sufficient for categorization, and their mutual spatial position was of lower importance. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Seismic analysis of ITER fourth PF (Poloidal Field Coil) feeder

    International Nuclear Information System (INIS)

    Liu, Sumei; Chen, Wei; Song, Yuntao; Ni, Xiaojun; Wang, Zhongwei; Chen, Yonghua; Gong, Chenyu

    2014-01-01

    The ITER feeder systems connect the ITER magnet systems located inside the main cryostat to the cryo-plant, power-supply and control system interfaces outside the cryostat. The main purpose of the feeders is to convey the cryogenic supply and electrical power to the coils as well as house the instrumentation wiring. The PF busbar which carries 52 kA current will suffer from high Lorentz force due to the background magnetic field inspired by the coils and the self-field between every pair of busbars. Except their mechanical strength and thermal insulation performance must be achieved, the dynamic mechanism on PF structure should be assessed. This paper presents the simulation and seismic analysis on ITER 4th PF feeder including the Coil Terminal Box and S-bend Box (CTB and SBB), the Cryostat Feed-through (CFT), the In-Cryostat-Feeder (ICF), especially for the ground supports and main outer-tube firstly. This analysis aims to study seismic resistance on system design under local seismograms with floor response spectrum, the structural response vibration mode and response duration results of displacement, membrane stress, and bending stress on structure under different directions actuating signals were obtained by using the single-seismic spectrum analysis and Dead Weight analysis respectively. Based on the simulative and analytical results, the system seismic resistance and the integrity of the support structure in the 4th PF feeder have been studied and the detail design confirmed

  14. A Markov chain model for CANDU feeder pipe degradation

    International Nuclear Information System (INIS)

    Datla, S.; Dinnie, K.; Usmani, A.; Yuan, X.-X.

    2008-01-01

    There is need for risk based approach to manage feeder pipe degradation to ensure safe operation by minimizing the nuclear safety risk. The current lack of understanding of some fundamental degradation mechanisms will result in uncertainty in predicting the rupture frequency. There are still concerns caused by uncertainties in the inspection techniques and engineering evaluations which should be addressed in the current procedures. A probabilistic approach is therefore useful in quantifying the risk and also it provides a tool for risk based decision making. This paper discusses the application of Markov chain model for feeder pipes in order to predict and manage the risks associated with the existing and future aging-related feeder degradation mechanisms. The major challenge in the approach is the lack of service data in characterizing the transition probabilities of the Markov model. The paper also discusses various approaches in estimating plant specific degradation rates. (author)

  15. Configuration System for Simulation Based Design of Vibratory Bowl Feeders

    DEFF Research Database (Denmark)

    Hansson, Michael Natapon; Mathiesen, Simon; Ellekilde, Lars-Peter

    2017-01-01

    Vibratory bowl feeders are still among the most commonly used production equipment for automated part feeding, where parts are correctly oriented for further manipulation by being conveyed through a set of orienting devices. Designing vibratory bowl feeders involves selecting and sequencing...... a number of these devices that either reorients or rejects the part until a desirable orientation is achieved. To aid the designer in this task, this work presents a configuration system where knowledge of the behaviour for each device is acquired through dynamic simulation, and used to solve...

  16. Rapeseed with tolerance to the non selective herbicide glufosinate ammonium

    Energy Technology Data Exchange (ETDEWEB)

    Rasche, E. [Hoechst Schering AgrEvo GmbH, Frankfurt am Main (Germany)

    1998-12-31

    Weed control with herbicides is essential to grow rapeseed. Glufosinate Ammonium is used as a non selective herbicide successfully in many countries for over 10 years. It conforms well with ever increasing safety standards for human beings, animals and the environment. The tolerance of rapeseed and other crop plants was achieved by genetic modification. A resistance gene (PAT or BAR) was transfered into previously susceptible rapeseed plants. This new approach allowed the development of Glufosinate Ammonium as an almost ideal selective herbicide. In cooperation with major seed companies and by own breeding programmes new Glufosinate tolerant rapeseed varieties and hybrids are developed. Data on metabolism, toxicity, residues, efficacy etc. were generated to get registration for the selective herbicide use. In addition various studies were done for safety assessments of the PAT gene and the modified rapeseed. In spring 1995 Canadian authorities granted worldwide the first approvals for the selective use of Glufosinate Ammonium (trademark Liberty) and Glufosinate tolerant (trademark and logo Liberty Link) spring rapeseed (Canola). After a successful launch in 1995 about 150.000 ha of Liberty Link Canola were grown and treated with Liberty in 1996. The Liberty Link Canola growers were very well satisfied. In a grower survey 84% stated that they will definitely use the Liberty Link System again. In Europe registrations for Glufosinate Ammonium as a selective herbicide and for the first Glufosinate tolerant rapeseed varieties are expected in the course of 1997. The Liberty Link System will be launched in rapeseed most probably in 1998. (orig.)

  17. Microplastic in a macro filter feeder: humpback whale Megaptera novaeangliae

    NARCIS (Netherlands)

    Besseling, E.; Foekema, E.M.; Franeker, van J.A.; Leopold, M.F.; Bravo Rebolledo, E.; Kuehn, S.; Mielke, L.; Heberle-Bors, E.; Ijzer, J.; Kamminga, P.; Koelmans, A.A.

    2015-01-01

    Marine filter feeders are exposed to microplastic because of their selection of small particles as food source. Baleen whales feed by filtering small particles from large water volumes. Macroplastic was found in baleen whales before. This study is the first to show the presence of microplastic in

  18. Optimisation of Trap Design for Vibratory Bowl Feeders

    DEFF Research Database (Denmark)

    Mathiesen, Simon; Sørensen, Lars Carøe; Kraft, Dirk

    2018-01-01

    Vibratory bowl feeders (VBFs) are a widely used option for industrial part feeding, but their design is still largely manual. A subtask of VBF design is determining an optimal parameter set for the passive devices, called traps, which the VBF uses to ensure correct part orientation. This paper...

  19. Microplastic in a macro filter feeder: Humpback whale Megaptera novaeangliae.

    NARCIS (Netherlands)

    E., Besseling,; E.M., Foekema,; J.A. van, Franeker; Leopold, Mardik F; Kuhn, S.; Bravo Rebolledo, E.L.; Hese, E.; Mielke, L.; IJzer, J.|info:eu-repo/dai/nl/304839663; Kamminga, P.; Koelmans, A.A.

    2015-01-01

    Marine filter feeders are exposed to microplastic because of their selection of small particles as food source. Baleen whales feed by filtering small particles from large water volumes. Macroplastic was found in baleen whales before. This study is the first to show the presence of microplastic in

  20. A hybrid evolutionary algorithm for distribution feeder reconfiguration

    Indian Academy of Sciences (India)

    the reconfiguration of distribution networks has been proposed by .... An effective strategy to increase the loading margin of heavily loaded feeders is to ... social animals such as a flock of birds, a school of fish or a group of people that pursue.

  1. Novel Methods to Determine Feeder Locational PV Hosting Capacity and PV Impact Signatures

    Energy Technology Data Exchange (ETDEWEB)

    Reno, Matthew J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Coogan, Kyle [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Seuss, John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Broderick, Robert Joseph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-05-01

    Often PV hosting capacity analysis is performed for a limited number of distribution feeders. For medium - voltage distribution feeders, previous results generally analyze less than 20 feeders, and then the results are extrapolated out to similar types of feeders. Previous hosting capacity research has often focused on determining a single value for the hosting capacity for the entire feeder, whereas this research expands previous hosting capacity work to investigate all the regions of the feeder that may allow many different hosting capacity values wit h an idea called locational hosting capacity (LHC)to determine the largest PV size that can be interconnected at different locations (buses) on the study feeders. This report discusses novel methods for analyzing PV interconnections with advanced simulati on methods. The focus is feeder and location - specific impacts of PV that determine the locational PV hosting capacity. Feeder PV impact signature are used to more precisely determine the local maximum hosting capacity of individual areas of the feeder. T he feeder signature provides improved interconnection screening with certain zones that show the risk of impact to the distribution feeder from PV interconnections.

  2. Round-bale feeder design affects hay waste and economics during horse feeding.

    Science.gov (United States)

    Martinson, K; Wilson, J; Cleary, K; Lazarus, W; Thomas, W; Hathaway, M

    2012-03-01

    Many horse owners find round bales convenient, less labor intensive, and more affordable than other hay types, but report an inability to control horse BW gain and excessive hay waste. The objectives were to compare hay waste, hay intake, and payback of 9 round-bale feeders and a no-feeder control when used during horse feeding. Nine round-bale feeders were tested: Cinch Net, Cone, Covered Cradle, Hayhut, Hay Sleigh, Ring, Tombstone, Tombstone Saver, and Waste Less. Each feeder design was placed on the ground in a dirt paddock. Five groups of 5 horses were fed in rotation for a 4-d period with each feeder. Every fourth day, groups were rotated among paddocks and a new round bale was placed in each feeder. In the 5 paddocks used, 5 feeders were installed for d 1 through 20, and the remaining 4 feeders and no-feeder control were installed for d 21 through 40. Groups of horses were sequentially assigned to feeders using two 5 × 5 Latin squares, the first for d 1 through 20, the second for d 21 through 40. Horse groups of similar age, BW, breed, and sex were formed from 25 Quarter Horse and Thoroughbred geldings and open mares (means: 11 yr; 541 kg of BW). Hay on the ground surrounding the feeder was collected daily, dried, and weighed. The total amount of hay removed around each feeder for a 4-d period was considered waste. Dry matter intake was estimated as the difference between hay disappearance and waste. Number of months for the reduction in waste to repay feeder cost (payback) were calculated using hay valued at $110/t, and improved feeder efficiency over the control. Feeder design did not affect hay intake (P > 0.05); all feeders resulted in an estimated hay intake of 2.0 to 2.4% BW; the no-feeder control resulted in a reduced intake of 1.3% BW (P = 0.001). Mean percentage of hay waste differed among feeders (P feeder control, 57%. Feeder design also affected payback (P feeder design affected hay waste and payback, but not estimated hay intake or BW change

  3. Feeding Against Gravity with Spot Feeders in High Silicon Ductile Iron

    DEFF Research Database (Denmark)

    Vedel-Smith, Nikolaj Kjelgaard; Tiedje, Niels Skat

    2014-01-01

    and classified using X-ray imaging and ultrasound analysis. The effect of the different feeder configurations were classified in reference to defect location, sleeve material, and feeder type, modulus, and location. The analysis showed that exothermal feeder sleeves with the right configurations can feed up......-hill against gravity. This effect may contribute to the thermal expansion created by the exothermal reaction. It was also found that the optimum feeder size does not scale linearly with the casting modulus but that larger casting modulus requires relatively smaller modulus feeders. The thermal gradient created...

  4. Feederism: an exaggeration of a normative mate selection preference?

    Science.gov (United States)

    Terry, Lesley L; Suschinsky, Kelly D; Lalumière, Martin L; Vasey, Paul L

    2012-02-01

    Quinsey and Lalumière (1995) suggested that some, if not most, paraphilias are exaggerated manifestations of more normative and functional mate selection preferences. The present study tested whether Feederism, a fat fetish focused on erotic eating, feeding, and gaining weight, is an exaggeration of a sexual arousal pattern commonly seen in the general population. Thirty participants (15 men and 15 women) recruited from the general population were assessed using penile plethysmography and vaginal photoplethysmography, respectively. None of the participants were self-identified Feeders or Feedees. Participants were shown sexual, neutral, and feeding still images while listening to audio recordings of sexual, neutral, and feeding stories. Participants did not genitally respond to feeding stimuli. However, both men and women subjectively rated feeding stimuli as more sexually arousing than neutral stimuli. We discuss the discordance between physiological and self-reported sexual arousal in the context of sex differences in sexual concordance and implications for future research.

  5. Digital optical feeder links system for broadband geostationary satellite

    Science.gov (United States)

    Poulenard, Sylvain; Mège, Alexandre; Fuchs, Christian; Perlot, Nicolas; Riedi, Jerome; Perdigues, Josep

    2017-02-01

    An optical link based on a multiplex of wavelengths at 1.55μm is foreseen to be a valuable solution for the feeder link of the next generation of high-throughput geostationary satellite. The main satellite operator specifications for such link are an availability of 99.9% over the year, a capacity around 500Gbit/s and to be bent-pipe. Optical ground station networks connected to Terabit/s terrestrial fibers are proposed. The availability of the optical feeder link is simulated over 5 years based on a state-of-the-art cloud mask data bank and an atmospheric turbulence strength model. Yearly and seasonal optical feeder link availabilities are derived and discussed. On-ground and on-board terminals are designed to be compliant with 10Gbit/s per optical channel data rate taking into account adaptive optic systems to mitigate the impact of atmospheric turbulences on single-mode optical fiber receivers. The forward and return transmission chains, concept and implementation, are described. These are based on a digital transparent on-off keying optical link with digitalization of the DVB-S2 and DVB-RCS signals prior to the transmission, and a forward error correcting code. In addition, the satellite architecture is described taking into account optical and radiofrequency payloads as well as their interfaces.

  6. Some software issues in mapping of power distribution feeders

    International Nuclear Information System (INIS)

    Mufti, I.A.

    1994-01-01

    This paper is about the in-house developed software for distribution feeders mapping project. It first gives birds eye view of the project, highlight its technical complexity in management and logistics, introduced by sheer size of the project. It gives an overview of the software developed and the moves on to describe circuit tracing, circuit model, leaves isolation (for tree structured network) and backtracking in more detail among many different parts of software, description of all which is not possible because of space limitations. (author)

  7. Stress analysis of feeder bends using neutrons: new results and cumulative impacts

    Energy Technology Data Exchange (ETDEWEB)

    Banks, D.; Donaberger, R. [Canadian Neutron Beam Centre, Chalk River, ON (Canada); Leitch, B. [Atomic Energy of Canada Limited, Chalk River, ON (Canada); Rogge, R.B. [Canadian Neutron Beam Centre, Chalk River, ON (Canada)

    2014-07-01

    Neutron diffraction has played a vital role in stress analysis of bends in carbon steel pipes, known as feeder pipes, in CANDU reactors. Due to incidents of cracking of feeders, extensive R&D programs to manage feeder cracking have been implemented over about ten years. We review the cumulative impacts of this research from the view point of the stress analysis using neutrons, and present new results by examining a feeder bend with a partial crack both experimentally using neutron diffraction and theoretically using a finite element model. (author)

  8. limit loads for wall-thinning feeder pipes under combined bending and internal pressure

    International Nuclear Information System (INIS)

    Je, Jin Ho; Lee, Kuk Hee; Chung, Ha Joo; Kim, Ju Hee; Han, Jae Jun; Kim, Yun Jae

    2009-01-01

    Flow Accelerated Corrosion (FAC) during inservice conditions produces local wall-thinning in the feeder pipes of CANDU. The Wall-thinning in the feeder pipes is main degradation mechanisms affecting the integrity of piping systems. This paper discusses the integrity assessment of wall-thinned feeder pipes using limit load analysis. Based on finite element limit analyses, this paper compare limit loads for wall-thinning feeder pipes under combined bending and internal pressure with proposed limit loads. The limit loads are determined from limit analyses based on rectangular wall-thinning and elastic-perfectly-plastic materials using the large geometry change.

  9. An evaluation of the choice of feeder cell growth arrest for the production of cultured epidermis.

    Science.gov (United States)

    Chugh, Rishi Man; Chaturvedi, Madhusudan; Yerneni, Lakshmana Kumar

    2015-12-01

    Growth arrested 3T3 cells have been used as feeder cells in human epidermal keratinocyte cultures to produce cultured epidermal autografts for the treatment of burns. The feeder cells were ideally growth-arrested by gamma-irradiation. Alternatively, growth arrest by mitomycin C treatment is a cost effective option. We compared the functional efficacy of these two approaches in keratinocyte cultures by colony forming efficiency, the net growth area of colonies, BrdU labeling and histological features of cultured epidermal sheets. The growth area estimation involved a semi-automated digital technique using the Adobe Photoshop and comprised of isolation and enumeration of red pixels in Rhodamine B-stained keratinocyte colonies. A further refinement of the technique led to the identification of critical steps to increasing the degree of accuracy and enabling its application as an extension of colony formation assay. The results on feeder cell functionality revealed that the gamma irradiated feeders influenced significantly higher colony forming efficiency and larger growth area than the mitomycin C treated feeders. The BrdU labeling study indicated significant stimulation of the overall keratinocyte proliferation by the gamma irradiated feeders. The cultured epidermal sheets produced by gamma feeders were relatively thicker than those produced by mitomycin C feeders. We discussed the clinical utility of mitomycin C feeders from the viewpoint of cost-effective burn care in developing countries. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

  10. S08: investigation and repair of a cracked feeder at Point Lepreau GS

    International Nuclear Information System (INIS)

    A Celovsky, A.; Wright, M.D.; Gendron, T.S.

    1997-01-01

    Early in 1997 investigation of a low level leak in the Point Lepreau GS (PLGS) PHTS revealed that an outlet feeder, S08, was leaking. Ultrasonic inspection, and subsequent failure analysis, revealed that the leak was a consequence of a crack. Given the unusual nature of this event, and current concerns over feeder thinning, a detailed and careful removal and examination procedure was developed. The S08 outlet feeder was removed and shipped to Chalk River Laboratories for examination. The examination confirmed that the failure was a through-wall crack, most likely the consequence of stress corrosion cracking. A critical point of the analysis was to determine how the crack initiated, and subsequently propagated. High residual stresses and possible abnormal loading in conjunction with chemistry environments resulted in the Stress Corrosion Cracking (SCC) of the S08 outlet feeder bend. It is recognized that some of the causative factors implicated in the S08 failure apply to other outlet feeders. In particular, residual stresses in the non-stress-relieved, short-radius cold bent pipes will remain relatively high over the future life of the feeders. However, the risk of CANDU feeder failure by SCC is judged to be extremely low based on the evidence of the inspections carried out to date and the good performance record of feeder pipe in the CANDU industry. The channel was restored to its locked configuration, and the failed section of feeder replaced. (author)

  11. Experience of superconducting current feeders system of SST-1

    International Nuclear Information System (INIS)

    Gupta, N.C.; Garg, A.; Sonara, D.

    2014-01-01

    The superconducting current feeder system for SST-1 which has been installed and commissioned recently along with SST-1, felicitates to energize the SST-1. The CFS consists of ten pairs of 10,000 Ampere (A) rating helium vapor cooled conventional current leads, interconnecting Cu-SC joints, three numbers of cryo-compatible SC feeders ducts, current leads assembly chamber, hydraulic network and three numbers of joint boxes operated at different current rating to charge Toroidal Field and Poloidal Field coils separately. During the last three campaigns, it was possible to achieve a controlled cool down up to 4 K and showed its rated operational performance. Actively cooled liquid nitrogen shield showed temperature profile in the temperature range of 80-85K and the whole system was evacuated up to 6x10 -6 mbar. The measured LHe consumption rates from TF VCCL were 0.3 g/s and 0.35 g/s at zero current and 1 kA respectively. (author)

  12. DYNAMICS OF VIBRATION FEEDERS WITH A NONLINEAR ELASTIC CHARACTERISTIC

    Directory of Open Access Journals (Sweden)

    V. I. Dyrda

    2017-04-01

    Full Text Available Purpose. Subject to the smooth and efficient operation of each production line, is the use of vehicles transporting high specification. It worked well in practice for transporting construction machines, which are used during the vibration. The use of vibration machines requires optimization of their operation modes. In the form of elastic link in them are increasingly using rubber-metallic elements, which are characterized by nonlinear damping properties. So it is necessary to search for new, more modern, methods of calculation of dynamic characteristics of the vibration machines on the properties of rubber as a cushioning material. Methodology. The dynamics of vibration machine that is as elastic rubber block units and buffer shock absorbers limiting the amplitude of the vibrations of the working body. The method of determining amplitude-frequency characteristics of the vibrating feeder is based on the principle of Voltaire, who in the calculations of the damping properties of the dampers will allow for elastic-hereditary properties of rubber. When adjusting the basic dynamic stiffness of the elastic ties and vibratory buffers, using the principle of heredity rubber properties, determine the dependence of the amplitude of the working body of the machine vibrations. This method is called integro-operator using the fractional-exponential kernels of relaxation. Findings. Using the derived formula for determining the amplitude of the resonance curve is constructed one-mass nonlinear system. It is established that the use of the proposed method of calculation will provide a sufficiently complete description of the damping parameters of rubber-metallic elements and at the same time be an effective means of calculating the amplitude-frequency characteristics of nonlinear vibration systems. Originality. The authors improved method of determining damping characteristics of rubber-metallic elements and the amplitude-frequency characteristics of nonlinear

  13. harmonic load modeling: a case study of 33 kv abuja steel mill feeder

    African Journals Online (AJOL)

    HOD

    techniques are adopted. This paper studied the harmonic orders of the 33 kV Abuja Steel Feeder modeled as a ... (ETAP) software package was deployed to perform Discrete Fast Transform (DFT) while the input ... and documented in research and development articles ... network with 33kV Abuja Steel feeder as case study.

  14. Final report on the evolution of supporting conditions for the feeders of 500 MWe PHWR

    International Nuclear Information System (INIS)

    Mishra, Rajesh; Soni, R.S.; Kushawaha, H.S.; Mahajan, S.C.; Kakodkar, A.; Hariprasad, K.

    1994-01-01

    This report deals with the evolution of generic supporting conditions for the feeders of 500 MWe PHWR based on the analysis and qualification of a few representative feeders. There are 196 different feeder pipe configurations for a total of 748 feeders. The present analysis was aimed at evolving a generalised supporting criteria based on the analysis of some representative feeders. The analysis was carried out for various loadings viz. pressure, temperature, dead weight, operating basis earthquake (OBE), safe shutdown earthquake (SSE) and creep loadings. The analysis for OBE and SSE loadings were carried out using response spectrum method. The effect of spacers between various feeders was modelled using higher damping values than those prescribed in ASME code. Based on the above analyses, generic supporting arrangements for the feeders of various groups have been finalized. This report gives details about the mathematical modelling, the analysis approach, the optimised supporting criteria, finalization of grouping and fixing of boundaries between various groups of feeders. (author). 34 refs., 51 figs., 69 tabs

  15. Development of I and C system for the coal feeder of coal firing plant

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Teak Soo; Park, Chan Ho [Korea Electric Power Corp. (KEPCO), Taejon (Korea, Republic of). Research Center

    1996-12-31

    KECC(Kepco Coal Feeder Control System) receives coal weight, conveyor speed and boiler demand signals. It controls coal flow by generating speed signal of feeder which conveys coal in hopper to pulverizer, displaying measured coal quantity and providing local auto and manual manipulator (author). 33 figs.

  16. Evaluation of options for life cycle management of feeder cracking at the Point Lepreau Generating Station

    International Nuclear Information System (INIS)

    Gendron, T.S.; Slade, J.P.

    2003-01-01

    The CANDU industry has a predictive capability for most Heat Transport System (HTS) degradation issues that allows utilities to apply cost-effective maintenance programs. The standard approach for maintenance programs is focussed inspection and planned replacement. Some examples of degradation issues with deterministic failure rates are feeder thinning, and pressure tube elongation and deuterium ingress. However, the cracking observed in Point Lepreau Generating Station (PLGS) outlet feeder first bends is one notable exception to this behaviour. A predictive capability for feeder cracking does not currently exist for several reasons. First, the mechanism of feeder cracking, stress corrosion cracking (SCC), has to some degree a random nature. Second, although a probable environment causing cracking has been identified, the precise stress and environmental conditions for feeder crack initiation and propagation have not been defined. Finally, the very low incidence of feeder cracking observed to-date (four, all at PLGS) precludes a probabilistic or statistical prediction of failure rate. Generally, utilities select a Life Cycle Management Plan that ensures safe operation and has the lowest Net Present Value cost. In preparing a Feeder Life Cycle Management Plan, New Brunswick Power (NBP) has recognized that the Net Present Value cost is very sensitive to failure rate. Since the failure rate for feeder cracking is not well defined, the following three scenarios were considered to bound the probability of future failures at PLGS. (author)

  17. Feeder cells support the culture of induced pluripotent stem cells even after chemical fixation.

    Directory of Open Access Journals (Sweden)

    Xiao-Shan Yue

    Full Text Available Chemically fixed mouse embryonic fibroblasts (MEFs, instead of live feeder cells, were applied to the maintenance of mouse induced pluripotent stem (miPS cells. Formaldehyde and glutaraldehyde were used for chemical fixation. The chemically fixed MEF feeders maintained the pluripotency of miPS cells, as well as their undifferentiated state. Furthermore, the chemically fixed MEF feeders were reused several times without affecting their functions. These results indicate that chemical fixation can be applied to modify biological feeders chemically, without losing their original functions. Chemically fixed MEF feeders will be applicable to other stem cell cultures as a reusable extracellular matrix candidate that can be preserved on a long-term basis.

  18. Preliminary analysis of accident in SST-1 current feeder system

    International Nuclear Information System (INIS)

    Roy, Swati; Kanabar, Deven; Garg, Atul; Singh, Amit; Tanna, Vipul; Prasad, Upendra; Srinivasan, R.

    2017-01-01

    Steady-state Tokamak-1 (SST-1) has 16 superconducting Toroidal field (TF) and 9 superconducting poloidal field (PF) coils rated for 10kA DC. All the TF are connected in series and are operated in DC condition whereas PF coils are individually operated in pulse mode during SST-1 campaigns. SST-1 current feeder system (CFS) houses 9 pairs of PF current leads and 1 pair of TF current leads. During past SST-1 campaign, there were arcing incidents within SST-1 CFS chamber which caused significant damage to PF superconducting current leads as well as its Helium cooling lines of the current leads. This paper brings out the preliminary analysis of the mentioned arcing incident, possible reasons and its investigation thereby laying out the sequence of events. From this analysis and observations, various measures to avoid such arcing incidents have also been proposed. (author)

  19. Microplastic in a macro filter feeder: Humpback whale Megaptera novaeangliae.

    Science.gov (United States)

    Besseling, E; Foekema, E M; Van Franeker, J A; Leopold, M F; Kühn, S; Bravo Rebolledo, E L; Heße, E; Mielke, L; IJzer, J; Kamminga, P; Koelmans, A A

    2015-06-15

    Marine filter feeders are exposed to microplastic because of their selection of small particles as food source. Baleen whales feed by filtering small particles from large water volumes. Macroplastic was found in baleen whales before. This study is the first to show the presence of microplastic in intestines of a baleen whale (Megaptera novaeangliae). Contents of its gastrointestinal tract were sieved, dissolved in 10% potassium hydroxide and washed. From the remaining dried material, potential synthetic polymer particles were selected based on density and appearance, and analysed by Fourier transform infrared (FTIR) spectroscopy. Several polymer types (polyethylene, polypropylene, polyvinylchloride, polyethylene terephthalate, nylon) were found, in varying particle shapes: sheets, fragments and threads with a size of 1mm to 17cm. This diversity in polymer types and particle shapes, can be interpreted as a representation of the varying characteristics of marine plastic and the unselective way of ingestion by M. novaeangliae. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Development of an extruder-feeder biomass direct liquefaction process

    Energy Technology Data Exchange (ETDEWEB)

    White, D.H.; Wolf, D. (Arizona Univ., Tucson, AZ (United States). Dept. of Chemical Engineering)

    1991-10-01

    As an abundant, renewable, domestic energy resource, biomass could help the United States reduce its dependence on imported oil. Biomass is the only renewable energy technology capable of addressing the national need for liquid transportation fuels. Thus, there is an incentive to develop economic conversion processes for converting biomass, including wood, into liquid fuels. Through research sponsored by the US DOE's Biomass Thermochemical Conversion Program, the University of Arizona has developed a unique biomass direct liquefaction system. The system features a modified single-screw extruder capable of pumping solid slurries containing as high as 60 wt% wood flour in wood oil derived vacuum bottoms at pressures up to 3000 psi. The extruder-feeder has been integrated with a unique reactor by the University to form a system which offers potential for improving high pressure biomass direct liquefaction technology. The extruder-feeder acts simultaneously as both a feed preheater and a pumping device for injecting wood slurries into a high pressure reactor in the biomass liquefaction process. An experimental facility was constructed and following shakedown operations, wood crude oil was produced by mid-1985. By July 1988, a total of 57 experimental continuous biomass liquefaction runs were made using White Birch wood feedstock. Good operability was achieved at slurry feed rates up to 30 lb/hr, reactor pressures from 800 to 3000 psi and temperatures from 350{degree}C to 430{degree}C under conditions covering a range of carbon monoxide feed rates and sodium carbonate catalyst addition. Crude wood oils containing as little as 6--10 wt% residual oxygen were produced. 38 refs., 82 figs., 26 tabs.

  1. A Feeder-Bus Dispatch Planning Model for Emergency Evacuation in Urban Rail Transit Corridors

    Science.gov (United States)

    Wang, Yun; Yan, Xuedong; Zhou, Yu; Zhang, Wenyi

    2016-01-01

    The mobility of modern metropolises strongly relies on urban rail transit (URT) systems, and such a heavy dependence causes that even minor service interruptions would make the URT systems unsustainable. This study aims at optimally dispatching the ground feeder-bus to coordinate with the urban rails’ operation for eliminating the effect of unexpected service interruptions in URT corridors. A feeder-bus dispatch planning model was proposed for the collaborative optimization of URT and feeder-bus cooperation under emergency situations and minimizing the total evacuation cost of the feeder-buses. To solve the model, a concept of dummy feeder-bus system is proposed to transform the non-linear model into traditional linear programming (ILP) model, i.e., traditional transportation problem. The case study of Line #2 of Nanjing URT in China was adopted to illustrate the model application and sensitivity analyses of the key variables. The modeling results show that as the evacuation time window increases, the total evacuation cost as well as the number of dispatched feeder-buses decrease, and the dispatched feeder-buses need operate for more times along the feeder-bus line. The number of dispatched feeder-buses does not show an obvious change with the increase of parking spot capacity and time window, indicating that simply increasing the parking spot capacity would cause huge waste for the emergent bus utilization. When the unbalanced evacuation demand exists between stations, the more feeder-buses are needed. The method of this study will contribute to improving transportation emergency management and resource allocation for URT systems. PMID:27676179

  2. Impacting effects of seismic loading in feeder pipes of PHWR power plants

    International Nuclear Information System (INIS)

    Kumar, R.

    1996-01-01

    The core of a pressurized heavy water reactor (PHWR) consists of a large number of fuel channels. These fuel channels are connected to the feeder pipes through which the heavy water flows and transports heat from the reactor core to the steam generators. The feeder pipes are several hundreds in number. They run close to each other with small gaps and have several bends. Thus they represent a complex piping system. Under seismic loading, the adjacent feeder pipes may impact each other. In this paper a simplified procedure has been established to assess such impacting effects. The results of the proposed analysis include bending moment and impact force, which provide the stresses due to impacting effects. These results are plotted in nondimensional form so that they could be utilized for any set of feeder pipes. The procedure used for studying the impacting effects includes seismic analysis of individual feeder pipes without impacting effects, selection of pipes for impact analysis, and estimating their maximum impact velocity. Based on the static and dynamic characteristics of the selected feeder pipes, the maximum bending moment, impact force, and stresses are obtained. The results of this study are useful for quick evaluation of the impacting effects in feeder pipes

  3. Effects of Feeder Cells on Dopaminergic Differentiation of Human Embryonic Stem Cells

    Directory of Open Access Journals (Sweden)

    Zhenqiang Zhao

    2016-12-01

    Full Text Available Mouse embryonic fibroblasts (MEFs and human foreskin fibroblasts (HFFs are used for the culture of human embryonic stem cells (hESCs. MEFs and HFFs differed in their capacity to support the proliferation and pluripotency of hESCs and could affect cardiac differentiation potential of hESCs. The aim of this study was to evaluate the effect of MEFs and HFFs feeders on dopaminergic differentiation of hESCs lines. To minimize the impact of culture condition variation, two hESCs lines were cultured on mixed feeder cells (MFCs, MEFs: HFFs =1:1 and HFFs feeder respectively, and then were differentiated into DA neurons under the identical protocol. Dopaminergic differentiation was evaluated by immunocytochemistry, quantitative fluorescent real-time PCR (qRT-PCR, transmission and scanning electron microscopy, and patch clamp. Our results demonstrated that these hESCs-derived neurons were genuine and functional DA neurons. However, compared to hESCs line on MFCs feeder, hESCs line on HFFs feeder had a higher proportion of TH positive cells and expressed higher levels of FOXA2, PITX3, NURR1 and TH genes. In addition, the values of threshold intensity and threshold membrane potential of DA neurons from hESCs line on HFFs feeder were lower than those of DA neurons from hESCs line on the MFCs feeder. In conclusion, HFFs feeder not only facilitated the differentiation of hESCs cells into dopaminergic neurons, but also induced hESCs-derived DA neurons to express higher electrophysiological excitability. Therefore, feeder cells could affect not only dopaminergic differentiation potential of different hESCs lines, but also electrophysiological properties of hESCs-derived DA neurons.

  4. A novel method for decomposing electricity feeder load into elementary profiles from customer information

    International Nuclear Information System (INIS)

    Gerossier, Alexis; Barbier, Thibaut; Girard, Robin

    2017-01-01

    Highlights: •Use of aggregated electricity load profiles and customer description at feeder level. •Statistical recovery of elementary load profiles with customer categorization. •Generation of load demand profiles for unknown feeders and new local areas. •Relevancy of the different categorizations. -- Abstract: To plan a distribution grid involves making a long-term forecast of sub-hourly demand, which requires modeling the demand and its dynamics with aggregated measurement data. Distribution system operators (DSOs) have been recording electricity sub-hourly demand delivered by their medium-voltage feeders (around 1000—10,000 customers) for several years. Demand profiles differ widely among the various considered feeders. This is partly due to the varying mix of customer categories from one feeder to another. To overcome this issue, elementary demand profiles are often associated with customer categories and then combined according to a mix description. This paper presents a novel method to estimate elementary profiles that only requires several feeder demand curves and a description of customers. The method relies on a statistical blind source model and a new estimation procedure based on the augmented Lagrangian method. The use of feeders to estimate elementary profiles means that measurements are fully representative and continuously updated. We illustrate the proposed method through a case study comprising around 1000 feeder demand curves operated by the main French DSO Enedis. We propose an application o that uses the obtained profiles to evaluate the contribution of any set of new customers to a feeder peak load. We show that profiles enable a simulation of new unmeasured areas with errors of around 20%. We also show how our method can be used to evaluate the relevancy of different customer categorizations.

  5. Improvement of Local Voltage in Feeders with Photovoltaic using Electric Vehicles

    DEFF Research Database (Denmark)

    Marra, Francesco; Yang, Guangya; Fawzy, Y. T.

    2013-01-01

    In low-voltage (LV) feeders with high penetration of photovoltaic (PV), a major issue to be solved is voltage rise due to the active power injection. If no measures are taken, this may lead to generation’s interruptions and to the malfunctioning of domestic appliances due to non-standard voltage...... profiles. This paper proposes a storage strategy to alleviate voltage rise in feeders with PV, using coordinated electric vehicle (EV) load as the storage solution. The voltage support strategy is easy to implement practically and it is demonstrated on a test feeder emulating a household with roof...

  6. Diversity of selective and non-selective fishing gear and their impact ...

    African Journals Online (AJOL)

    This survey was conducted in Al-Kalakla Fishery (KF) and Jabel Awlia Dam Fishery (JADF) in the White Nile River, Khartoum state to identify the selective and non-selective fishing gear. The results showed the selective fishing gear represented by gill-nets and seine nets (beach nets) in both fisheries with clear variation in ...

  7. Non-selective beta-blockers decrease thrombotic events in patients with heart failure

    NARCIS (Netherlands)

    De Peuter, Olav R.; Souverein, Patrick C.; Klungel, Olaf H.; Lip, Gregory Y.; Buller, Harry R.; De Boer, Anthonius; Kamphuisen, Pieter W.

    2010-01-01

    Background: Beta-blockers are often prescribed to patients with heart failure (HF) without distinctions between types of beta-blockers. The 2002 COMET study showed superiority of carvedilol (a non-selective beta-blocker) over metoprolol (selective beta-blocker) on mortality and cardiovascular events

  8. Non-selective beta-blockers may reduce risk of hepatocellular carcinoma

    DEFF Research Database (Denmark)

    Thiele, Maja; Albillos, Agustín; Abazi, Rozeta

    2015-01-01

    BACKGROUND & AIMS: Non-selective beta-blockers (NSBB) are used in patients with cirrhosis and oesophageal varices. Experimental data suggest that NSBB inhibit angiogenesis and reduce bacterial translocation, which may prevent hepatocellular carcinoma (HCC). We therefore assessed the effect of NSBB...

  9. Non-Selective Lexical Access in Late Arabic-English Bilinguals: Evidence from Gating.

    Science.gov (United States)

    Boudelaa, Sami

    2018-02-07

    Previous research suggests that late bilinguals who speak typologically distant languages are the least likely to show evidence of non-selective lexical access processes. This study puts this claim to test by using the gating task to determine whether words beginning with speech sounds that are phonetically similar in Arabic and English (e.g., [b,d,m,n]) give rise to selective or non-selective lexical access processes in late Arabic-English bilinguals. The results show that an acoustic-phonetic input (e.g., [bæ]) that is consistent with words in Arabic (e.g., [bædrun] "moon") and English (e.g., [bæd] "bad") activates lexical representations in both languages of the bilingual. This non-selective activation holds equally well for mixed lists with words from both Arabic and English and blocked lists consisting only of Arabic or English words. These results suggest that non-selective lexical access processes are the default mechanism even in late bilinguals of typologically distant languages.

  10. Minimal incorporation of Deepwater Horizon oil by estuarine filter feeders

    International Nuclear Information System (INIS)

    Fry, Brian; Anderson, Laurie C.

    2014-01-01

    Highlights: • Oil from the Deepwater Horizon oil spill entered Louisiana bays in mid-2010. • Oil was used minimally (<1%) in diets of mussels and barnacles. • Also, oil did not enhance planktonic respiration rates. • Use of oil carbon was relatively small in these productive estuarine food webs. - Abstract: Natural abundance carbon isotope analyses are sensitive tracers for fates and use of oil in aquatic environments. Use of oil carbon in estuarine food webs should lead to isotope values approaching those of oil itself, −27‰ for stable carbon isotopes reflecting oil origins and −1000‰ for carbon-14 reflecting oil age. To test for transfer of oil from the 2010 Deepwater Horizon spill into estuarine food webs, filter-feeding barnacles (Balanus sp.) and marsh mussels (Geukensia demissa) were collected from Louisiana estuaries near the site of the oil spill. Carbon-14 analyses of these animals from open waters and oiled marshes showed that oil use was <1% and near detection limits estimated at 0.3% oil incorporation. Respiration studies showed no evidence for enhanced microbial activity in bay waters. Results are consistent with low dietary impacts of oil for filter feeders and little overall impact on respiration in the productive Louisiana estuarine systems

  11. Automatic feeder for small fish held in tanks

    Science.gov (United States)

    Joeris, Leonard S.

    1965-01-01

    The Northville (Michigan) Biological Station has been a center for study of the developmental morphology of coregonid fishes. This work requires the production of numerous individual series of lake herring, lake whitefish, and several species of chubs from parent fish of positively known identity. The offspring of individual pairs or groups of fish must be held in individual tanks from the time they hatch until they reach maturity. One of the important problems in this project has been the poor growth of most fish. Though some have grown well, their growth has been less than that of the same species in nature, and a few fish from each hatch have grown very slowly. Irregularity of feeding may contribute to the slow growth of laboratory fish. The hatchery caretaker feeds them several times during his 8-hour workday, but they must go without food during the remaining 16 hours. The high metabolic rate of small fish, however, appears to make them strongly inclined toward almost continual feeding. Belief that greater, more regular food consumption would result from a mechanical feeder providing a continuous supply of food over a longer period of the day led to development of the equipment described in this paper.

  12. Ecology of marine deposit feeders. Ed. by G. Lopez, C. Taghon and J. Levinton

    Digital Repository Service at National Institute of Oceanography (India)

    Royan, J

    stream_size 2 stream_content_type text/plain stream_name Indian_J_Mar_Sci_19_233.pdf.txt stream_source_info Indian_J_Mar_Sci_19_233.pdf.txt Content-Encoding ISO-8859-1 Content-Type text/plain; charset=ISO-8859-1 ...

  13. The function of alginic acid on the radioactive contamination of some marine invertebrates deposite-feeders

    International Nuclear Information System (INIS)

    Amiard-Triquet, C.

    1975-01-01

    The contamination of invertebrates by radionuclides in a sedimentary environment is a function of the mobility of radioactive ions and especially of the mode of sorption of the radionuclides on the sediment and the ion retention by the algines. Since the enzymatic system of species feeding on the sediment includes little or no alginase, there occurs no desorption of the radionuclides during the passage of the algines along the digestive tract [fr

  14. Fate and effects of fragrance material on the deposit feeder, Capitella teleta

    DEFF Research Database (Denmark)

    Dai, Lina; Selck, Henriette; Salvito, Daniel

    2010-01-01

    Fragrance materials (FMs) have been used ubiquitously at low concentrations in perfume, cosmetics, detergents etc. The primary pathway into the aquatic environment is down-the-drain on a continual basis. Most published papers about FMs are concerned with the polycyclic and nitro musks. Acetyl...... organic matter content in the sediment. Therefore, We used 3 worm densities (C. teleta of the same age at 0, 44,000 and 88,000 individuals per m2), sediments with different organic matter content (4% and 2.7%) and AC spiked sediment (0, 50, 100 µg AC/g dw sed), to examine the fate of sediment...

  15. Bioaccumulation and effect of sediment-associated silver in different forms in two marine deposit feeders

    DEFF Research Database (Denmark)

    Dai, Lina; Banta, Gary Thomas; Syberg, Kristian

    2014-01-01

    Due to wide spread applications of nanoparticles, including Ag, in our daily life, these novel particles are receiving increasing attention by risk assessors. Many studies have been performed to test the toxicity of nanoparticles at the subcellular level. Despite these findings, there is still...... limited information at the whole organism level as to whether metallo-nanoparticles differ in toxicity from the same metals added to the environment in ionic or bulk form. In the present study, two organisms (i.e., a marine polychaete, Capitella teleta and a marine bivalve, Macoma balthica) were exposed...... to sediment amended with Ag in various forms (ionic Ag(I), nano-sized Ag and micron-sized Ag), and toxic endpoints were assessed at the whole organism level. After exposure for several weeks, no significant toxic effects were detected (i.e., mortality, growth rate and condition index) at the whole organism...

  16. Bioavailability of heavy metals for the deposit feeder Macoma balthica with special emphasis on copper

    NARCIS (Netherlands)

    Absil, M.C.P.

    1993-01-01

    In coastal and estuarine regions of Western Europe, concentrations of contaminants in the sediment are often relatively high compared to the waterphase. Consequently, these contaminants might form a serious threat to animals living in and associated with the sediment.

    As a

  17. Decision Support for Optimal Repositioning of Containers in a Feeder System

    Directory of Open Access Journals (Sweden)

    Danijela Tuljak-Suban

    2008-03-01

    Full Text Available The transport of empty containers represents a seriousproblem in the fast growing sphere of maritime container transport.The most widespread type of container transport organizationin maritime transport is the hub and spoke mode, whichenables the transport of a great number of containers via largevessels between hub ports, from where feeder ships transport tosmaller ports that thus gravitate to the central hub port. The articlecontains a detailed analysis of the northern Adriatic portsand the feeder connections with the hub ports of the Mediterranean.A two-level VRPPD (Vehicle Routing Problem withPickup and Delivery problem is modelled on a graph, wherethe transport of full containers is privileged over the transport ofempty containers. This enables the simulation of the feeder systemin the n01them Adriatic, meaning that it shows the ship'soperator the movement programme with minimal transportcosts for the superfluous empty containers in the complex of theregular transports of full containers in the feeder system.

  18. Demonstration of Market-Based Real-Time Electricity Pricing on a Congested Feeder

    DEFF Research Database (Denmark)

    Larsen, Emil Mahler; Pinson, Pierre; le Ray, Guillaume

    2015-01-01

    Congestion management can delay grid reinforcements needed due to the growth of distributed technologies like photovoltaics and electric vehicles. This paper presents a method of congestion management for low voltage feeders using indirect control from the smart grid demonstration EcoGrid EU, where...... prices to 1900 houses, with a virtual feeder of 28 houses receiving congestion pricing. Simulations are used to calculate the cost from using this congestion management method, while demonstration results indicate that congestion can be managed successfully....

  19. Manufacture and test of seismic bellows for ITER magnet feeder

    International Nuclear Information System (INIS)

    Liu, Chen; Lu, Kun; Sheng, Liang; Song, Yuntao; Su, Jinjin; Su, Man; Gung, Chenyu

    2016-01-01

    Highlights: • The design of the double bellows was iterated with the results of analysis based on the Expansion Joint Manufacturers Association (EJMA) standard. • The seismic bellows was tested with cyclic pressurization of the interlayer space to 2 bars absolute pressure for 5 cycles. • 200 cycles of tensile fatigue test with 90 mm of stretching from the nominal design length. • A full tensile test with 315 mm of stretching from its nominal length was conducted. • The prototype bellows was qualified for its leak tightness (less than 1 × 10 −9 Pam 3 /s of helium) at all time during the qualification test. - Abstract: This paper presents the key manufacturing and testing processes of the prototype ITER feeder seismic bellows. The design of the double bellows was iterated with the results of analysis based on the Expansion Joint Manufacturers Association (EJMA) standard. Each inner and outer bellows was supported in dedicated molds and formed by a hydraulic pressure machine rated at 800 tons. The double bellows were constructed by welding individual collars to the end flanges. The seismic bellows was tested with cyclic pressurization of the interlayer space to 2 bars absolute pressure for 5 cycles. This was followed by 200 cycles of tensile fatigue test with 90 mm of stretching from the nominal design length. After the mechanical fatigue test, a full tensile test with 315 mm of stretching from its nominal length was conducted. Helium leak tests, with the sensitivity of the helium leak detector set to 1 × 10 −9 Pa m 3 /s of helium, were performed at different stages of pressure and mechanical tests. The prototype bellows was qualified for its leak tightness at all time during the qualification test.

  20. Manufacture and test of seismic bellows for ITER magnet feeder

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Chen, E-mail: liuchen@ipp.ac.cn [Institute of Plasma Physics Chinese Academy of Sciences, ShuShanhu Road No. 350, Hefei (China); Lu, Kun [Institute of Plasma Physics Chinese Academy of Sciences, ShuShanhu Road No. 350, Hefei (China); Sheng, Liang [AEROSUN-TOLA Expansion Joint Co., Ltd., Jiangjun Road No. 199, Nanjing (China); Song, Yuntao; Su, Jinjin [Institute of Plasma Physics Chinese Academy of Sciences, ShuShanhu Road No. 350, Hefei (China); Su, Man; Gung, Chenyu [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul-lez-Durance (France)

    2016-11-01

    Highlights: • The design of the double bellows was iterated with the results of analysis based on the Expansion Joint Manufacturers Association (EJMA) standard. • The seismic bellows was tested with cyclic pressurization of the interlayer space to 2 bars absolute pressure for 5 cycles. • 200 cycles of tensile fatigue test with 90 mm of stretching from the nominal design length. • A full tensile test with 315 mm of stretching from its nominal length was conducted. • The prototype bellows was qualified for its leak tightness (less than 1 × 10{sup −9} Pam{sup 3}/s of helium) at all time during the qualification test. - Abstract: This paper presents the key manufacturing and testing processes of the prototype ITER feeder seismic bellows. The design of the double bellows was iterated with the results of analysis based on the Expansion Joint Manufacturers Association (EJMA) standard. Each inner and outer bellows was supported in dedicated molds and formed by a hydraulic pressure machine rated at 800 tons. The double bellows were constructed by welding individual collars to the end flanges. The seismic bellows was tested with cyclic pressurization of the interlayer space to 2 bars absolute pressure for 5 cycles. This was followed by 200 cycles of tensile fatigue test with 90 mm of stretching from the nominal design length. After the mechanical fatigue test, a full tensile test with 315 mm of stretching from its nominal length was conducted. Helium leak tests, with the sensitivity of the helium leak detector set to 1 × 10{sup −9} Pa m{sup 3}/s of helium, were performed at different stages of pressure and mechanical tests. The prototype bellows was qualified for its leak tightness at all time during the qualification test.

  1. Changes in thunderstorm characteristics due to feeder cloud merging

    Science.gov (United States)

    Sinkevich, Andrei A.; Krauss, Terrence W.

    2014-06-01

    Cumulus cloud merging is a complex dynamical and microphysical process in which two convective cells merge into a single cell. Previous radar observations and numerical simulations have shown a substantial increase in the maximum area, maximum echo top and maximum reflectivity as a result of the merging process. Although the qualitative aspects of merging have been well documented, the quantitative effects on storm properties remain less defined. Therefore, a statistical assessment of changes in storm characteristics due to merging is of importance. Further investigation into the effects of cloud merging on precipitation flux (Pflux) in a statistical manner provided the motivation for this study in the Asir region of Saudi Arabia. It was confirmed that merging has a strong effect on storm development in this region. The data analysis shows that an increase in the median of the distribution of maximum reflectivity was observed just after merging and was equal to 3.9 dBZ. A detailed analysis of the individual merge cases compared the merged storm Pflux and mass to the sum of the individual Feeder and Storm portions just before merging for each case. The merged storm Pflux increased an average of 106% over the 20-min period after merging, and the mass increased on average 143%. The merged storm clearly became larger and more severe than the sum of the two parts prior to merging. One consequence of this study is that any attempts to evaluate the precipitation enhancement effects of cloud seeding must also include the issue of cloud mergers because merging can have a significant effect on the results.

  2. Differences in game reading between selected and non-selected youth soccer players.

    Science.gov (United States)

    Den Hartigh, Ruud J R; Van Der Steen, Steffie; Hakvoort, Bas; Frencken, Wouter G P; Lemmink, Koen A P M

    2018-02-01

    Applying an established theory of cognitive development-Skill Theory-the current study compares the game-reading skills of youth players selected for a soccer school of a professional soccer club (n = 49) and their non-selected peers (n = 38). Participants described the actions taking place in videos of soccer game plays, and their verbalisations were coded using Skill Theory. Compared to the non-selected players, the selected players generally demonstrated higher levels of complexity in their game-reading, and structured the information of game elements-primarily the player, teammate and field-at higher complexity levels. These results demonstrate how Skill Theory can be used to assess, and distinguish game-reading of youth players with different expertise, a skill important for soccer, but also for other sports.

  3. Celecoxib versus a non-selective NSAID plus proton-pump inhibitor: what are the considerations?.

    Science.gov (United States)

    Chen, Judy T; Pucino, Frank; Resman-Targoff, Beth H

    2006-01-01

    Nonsteroidal anti-inflammatory drugs (NSAIDs) are extensively used worldwide. However, associated adverse gastrointestinal effects (NSAID gastropathy) such as bleeding, perforation and obstruction result in considerable morbidity, mortality, and expense. Although it is essential to employ gastroprotective strategies to minimize these complications in patients at risk, controversy remains on whether celecoxib alone or a non-selective NSAID in conjunction with a proton-pump inhibitor (PPI) is a superior choice. Recent concerns regarding potential cardiovascular toxicities associated with cox-2 selective inhibitors may favor non-selective NSAID/PPI co-therapy as the preferred choice. Concomitant use of low-dose aspirin with any NSAID increases the risk of gastrointestinal complications and diminishes the improved gastrointestinal safety profile of celecoxib; whereas use of ibuprofen plus PPI regimens may negate aspirin's antiplatelet benefits. Evidence shows that concurrent use of a non-selective NSAID (such as naproxen) plus a PPI is as effective in preventing NSAID gastropathy as celecoxib, and may be more cost-effective. Patients failing or intolerant to this therapy would be candidates for celecoxib at the lowest effective dose for the shortest duration of time. Potential benefits from using low-dose celecoxib with a PPI in patients previously experiencing bleeding ulcers while taking NSAIDs remains to be proven. An evidence-based debate is presented to assist clinicians with the difficult decision-making process of preventing NSAID gastropathy while minimizing other complications.

  4. A new stalked filter-feeder from the middle Cambrian Burgess Shale, British Columbia, Canada.

    Directory of Open Access Journals (Sweden)

    Lorna J O'Brien

    Full Text Available Burgess Shale-type deposits provide invaluable insights into the early evolution of body plans and the ecological structure of Cambrian communities, but a number of species, continue to defy phylogenetic interpretations. Here we extend this list to include a new soft-bodied animal, Siphusauctum gregarium n. gen. and n. sp., from the Tulip Beds (Campsite Cliff Shale Member, Burgess Shale Formation of Mount Stephen (Yoho National Park, British Columbia. With 1,133 specimens collected, S. gregarium is clearly the most abundant animal from this locality.This stalked animal (reaching at least 20 cm in length, has a large ovoid calyx connected to a narrow bilayered stem and a small flattened or bulb-like holdfast. The calyx is enclosed by a flexible sheath with six small openings at the base, and a central terminal anus near the top encircled by indistinct openings. A prominent organ, represented by six radially symmetrical segments with comb-like elements, surrounds an internal body cavity with a large stomach, conical median gut and straight intestine. Siphusauctum gregarium was probably an active filter-feeder, with water passing through the calyx openings, capturing food particles with its comb-like elements. It often occurs in large assemblages on single bedding planes suggesting a gregarious lifestyle, with the animal living in high tier clusters. These were probably buried en masse more or less in-situ by rapid mud flow events.Siphusauctum gregarium resembles Dinomischus, another Cambrian enigmatic stalked animal. Principal points of comparison include a long stem with a calyx containing a visceral mass and bract-like elements, and a similar lifestyle albeit occupying different tiering levels. The presence in both animals of a digestive tract with a potential stomach and anus suggest a grade of organization within bilaterians, but relationships with extant phyla are not straightforward. Thus, the broader affinities of S. gregarium remain

  5. Development of a feeder device for logging residue for a drum chipper; Hakkurin syoetoen kehittaeminen energiapuulle

    Energy Technology Data Exchange (ETDEWEB)

    Leinonen, T.; Kemppainen, J P [Oulu Univ. (Finland). Dept. of Mechanical Engineering

    1997-12-01

    The aim of this project is to increase the productivity of a large drum chipper by developing a feeder device to be used especially when chipping logging residue. Logging residue from regeneration areas is the most important reserve of forest biomass for the production of renewable energy in Finland. It is possible ecologically and economically to use about 5 million m{sup 3} of logging residue yearly for energy purposes. Currently both large lorry based chippers and smaller forwarder based chippers are used for chipping logging residue. However even the latest versions of these chippers are not well equipped for chipping logging residue. The ball like shape of residue piles causes blockades, if too large amounts of residue are fed into the chipper. Keeping the material flow even is difficult. In this project a prototype of a feeder device will be designed and manufactured to exactly find out the problems, that occur when feeding logging residue to a chipper. The designed prototype is based on a tubular chassis, which supports a conveyor made of steel plates. Prototype also has a 2,5 m wide feeding table and a feeder roll, which is located above the conveyor just before the chipper opening. Both the conveyor and the feeder roll are powered by hydraulic motors. The maximum feeding force is 20 kN. For research purposes both hydraulic pressure and flow can be adjusted individually for both motors. During 1996 activities included designing and building the prototype feeder device. In 1997 the prototype will be tested to find out possible problems, which need to be cured. After problems are solved and other improvements are made, the feeder device will be installed to an existing chipper and then tested again to determine the productivity of the new feeder device compared to the old unit. (orig.)

  6. Expression and secretory profile of buffalo fetal fibroblasts and Wharton's jelly feeder layers.

    Science.gov (United States)

    Parmar, Mehtab S; Mishra, Smruti Ranjan; Somal, Anjali; Pandey, Sriti; Kumar, G Sai; Sarkar, Mihir; Chandra, Vikash; Sharma, G Taru

    2017-05-01

    The present study examined the comparative expression and secretory profile of vital signaling molecules in buffalo fetal fibroblasts (BFF) and Wharton's jelly (BWJ) feeder layers at different passages. Both feeder layers were expanded up to 8th passage. Signaling molecules viz. bone morphogenetic protein 4 (BMP4), fibroblast growth factor 2 (FGF2), leukemia inhibitory factor (LIF) and transforming growth factor beta 1 (TGFB1) and pluripotency-associated transcriptional factors (POU5F1, SOX2, NANOG, KLF4, MYC and FOXD3) were immunolocalized in the both feeder types. A clear variation in the expression pattern of key signaling molecules with passaging was registered in both feeders compared to primary culture (0 passage). The conditioned media (CM) was collected from different passages (2, 4, 6, 8) of both the feeder layers and was quantified using enzyme-linked immunosorbent assay (ELISA). Concomitant to expression profile, protein quantification also revealed differences in the concentration of signaling molecules at different time points. Conjointly, expression and secretory profile revealed that 2nd passage of BFF and 6th passage of BWJ exhibit optimal levels of key signaling molecules thus may be selected as best passages for embryonic stem cells (ESCs) propagation. Further, the effect of mitomycin-C (MMC) treatment on the expression profile of signaling molecules in the selected passages of BFF and BWJ revealed that MMC modulates the expression profile of these molecules. In conclusion, the results indicate that feeder layers vary in expression and secretory pattern of vital signaling molecules with passaging. Based on these findings, the appropriate feeder passages may be selected for the quality propagation of buffalo ESCs. Copyright © 2017 Elsevier B.V. All rights reserved.

  7. Computational fluid dynamics analysis for flow accelerated corrosion in CANDU6 feeder pipes

    International Nuclear Information System (INIS)

    Catana, A.; Pauna, E.; Ioan, M.

    2013-01-01

    CANDU6 plant management over a long time period includes various ageing and degradation mechanisms like FAC manifested mainly at first and second elbow of CANDU6 outlet feeders. FAC take place at all CANDU6 built before 2000 year with feeders made from SA106 grade B low alloy carbon-steel (with chromium at 0.02%). CFD method is used in this paper to investigate the feeder's wall thinning process taking place mainly due local flow conditions in complex 3D geometrical configurations. The 380 outlet feeders grouped in 2.5'' (320) and 2.0'' feeders (60). The objective of this paper is to help, as much as possible, to focus investigation on most probable maximum thinning rate locations through 3D distribution of some TH parameters. Application of CFD methods in CANDU6 nuclear reactors implies the knowledge of real plant operating data like: long term time averaged channel power and mass flow as well as temperature, pressure, pHa etc allowing the optimization and cost reduction of wall thinning monitoring process at CANDU6 nuclear power plants. (authors)

  8. Network Reduction Algorithm for Developing Distribution Feeders for Real-Time Simulators: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Nagarajan, Adarsh; Nelson, Austin; Prabakar, Kumaraguru; Hoke, Andy; Asano, Marc; Ueda, Reid; Nepal, Shaili

    2017-06-15

    As advanced grid-support functions (AGF) become more widely used in grid-connected photovoltaic (PV) inverters, utilities are increasingly interested in their impacts when implemented in the field. These effects can be understood by modeling feeders in real-time systems and testing PV inverters using power hardware-in-the-loop (PHIL) techniques. This paper presents a novel feeder model reduction algorithm using a Monte Carlo method that enables large feeders to be solved and operated on real-time computing platforms. Two Hawaiian Electric feeder models in Synergi Electric's load flow software were converted to reduced order models in OpenDSS, and subsequently implemented in the OPAL-RT real-time digital testing platform. Smart PV inverters were added to the real-time model with AGF responses modeled after characterizing commercially available hardware inverters. Finally, hardware inverters were tested in conjunction with the real-time model using PHIL techniques so that the effects of AGFs on the choice feeders could be analyzed.

  9. Comparing the engineering program feeders from SiF and convention models

    Science.gov (United States)

    Roongruangsri, Warawaran; Moonpa, Niwat; Vuthijumnonk, Janyawat; Sangsuwan, Kampanart

    2018-01-01

    This research aims to compare the relationship between two types of engineering program feeder models within the technical education systems of Rajamangala University of Technology Lanna (RMUTL), Chiangmai, Thailand. To illustrate, the paper refers to two typologies of feeder models, which are the convention and the school in factory (SiF) models. The new SiF model is developed through a collaborative educational process between the sectors of industry, government and academia, using work-integrated learning. The research methodology were use to compared features of the the SiF model with conventional models in terms of learning outcome, funding budget for the study, the advantages and disadvantages from the point of view of students, professors, the university, government and industrial partners. The results of this research indicate that the developed SiF feeder model is the most pertinent ones as it meet the requirements of the university, the government and the industry. The SiF feeder model showed the ability to yield positive learning outcomes with low expenditures per student for both the family and the university. In parallel, the sharing of knowledge between university and industry became increasingly important in the process, which resulted in the improvement of industrial skills for professors and an increase in industrial based research for the university. The SiF feeder model meets its demand of public policy in supporting a skilled workforce for the industry, which could be an effective tool for the triple helix educational model of Thailand.

  10. Can non-selective beta-blockers prevent hepatocellular carcinoma in patients with cirrhosis?

    Science.gov (United States)

    Thiele, Maja; Wiest, Reiner; Gluud, Lise Lotte; Albillos, Agustín; Krag, Aleksander

    2013-11-01

    Hepatocellular carcinoma is the main liver-related cause of death in patients with compensated cirrhosis. The early phases are asymptomatic and the prognosis is poor, which makes prevention essential. We propose that non-selective beta-blockers decrease the incidence and growth of hepatocellular carcinoma via a reduction of the inflammatory load from the gut to the liver and inhibition of angiogenesis. Due to their effect on the portal pressure, non-selective beta-blockers are used for prevention of esophageal variceal bleeding. Recently, non-hemodynamic effects of beta-blockers have received increasing attention. Blockage of β-adrenoceptors in the intestinal mucosa and gut lymphatic tissue together with changes in type and virulence of the intestinal microbiota lead to reduced bacterial translocation and a subsequent decrease in the portal load of pathogen-associated molecular patterns. This may reduce hepatic inflammation. Blockage of β-adrenoceptors also decrease angiogenesis by inhibition of vascular endothelial growth factors. Because gut-derived inflammation and neo-angiogenesis are important in hepatic carcinogenesis, non-selective beta-blockers can potentially reduce the development and growth of hepatocellular carcinoma. Rodent and in vitro studies support the hypothesis, but clinical verification is needed. Different study designs may be considered. The feasibility of a randomized controlled trial is limited due to the necessary large number of patients and long follow-up. Observational studies carry a high risk of bias. The meta-analytic approach may be used if the incidence and mortality of hepatocellular carcinoma can be extracted from trials on variceal bleeding and if the combined sample size and follow up is sufficient. Copyright © 2013 Elsevier Ltd. All rights reserved.

  11. EV Charging Facilities and Their Application in LV Feeders with Photovoltaics

    DEFF Research Database (Denmark)

    Marra, Francesco; Yang, Guangya; Træholt, Chresten

    2013-01-01

    Low-voltage (LV) grid feeders with high penetration of photovoltaics (PVs) are often affected by voltage magnitude problems. To solve such issues, previous research has shown that reactive power methods, active power curtailment and grid reinforcement can be used for voltage support, yet showing...... several limits. We introduce the use of electric vehicle (EV) public charging stations with energy storage system (ESS) as a solution for voltage regulation in LV feeders with PV. A novel method is proposed to determine the ESS charging load required for voltage regulation and compare the results...... for the different locations in the feeder. With time-series simulations, we quantify the energy size required for a station ESS. A Belgian LV residential grid, modeled using real PV generation and load profiles, is used as case study. The method and simulation results show the effectiveness of using public EV...

  12. Convex relaxation of Optimal Power Flow in Distribution Feeders with embedded solar power

    DEFF Research Database (Denmark)

    Hermann, Alexander Niels August; Wu, Qiuwei; Huang, Shaojun

    2016-01-01

    There is an increasing interest in using Distributed Energy Resources (DER) directly coupled to end user distribution feeders. This poses an array of challenges because most of today’s distribution feeders are designed for unidirectional power flow. Therefore when installing DERs such as solar...... panels with uncontrolled inverters, the upper limit of installable capacity is quickly reached in many of today’s distribution feeders. This problem can often be mitigated by optimally controlling the voltage angles of inverters. However, the optimal power flow problem in its standard form is a large...... scale non-convex optimization problem, and thus can’t be solved precisely and also is computationally heavy and intractable for large systems. This paper examines the use of a convex relaxation using Semi-definite programming to optimally control solar power inverters in a distribution grid in order...

  13. A probabilistic degradation model for the estimation of the remaining life distribution of feeders

    International Nuclear Information System (INIS)

    Yuan, X.-X.; Pandey, M.D.; Bickel, G.A.

    2006-01-01

    Wall thinning due to flow accelerated corrosion (FAC) is a pervasive form of degradation in the outlet feeder pipes of the primary heat transport system of CANDU reactors. The prediction of the end-of-life of a feeder from wall thickness measurement data is confounded by the sampling and temporal uncertainties associated with the FAC degradation phenomenon. Traditional regression-based statistical methods deal with only the sampling uncertainties, leaving the temporal uncertainties unresolved. This paper presents an advanced probabilistic model, which is able to integrate the temporal uncertainties into the prediction of lifetime. In particular, a random gamma process model is proposed to model the FAC process and it is calibrated with a set of wall thickness measurements using the method of maximum likelihood. This information can be used to establish an optimum strategy for inspection and replacement of feeders. (author)

  14. Impact of Distribution Feeders that do not have Voltage Regulators on the number of Charged Electric Vehicles using IEEE 34 Bus Test Feeder

    Energy Technology Data Exchange (ETDEWEB)

    Allehyani, Ahmed [University of Southern California, Department of Electrical Engineering; Beshir, Mohammed [University of Southern California, Department of Electrical Engineering

    2015-02-01

    Voltage regulators help maintain an acceptable voltage profile for the system. This paper discusses the effect of installing voltage regulators to the system to fix the voltage drop resulting from the electrical vehicles loading increase when they are being charged. The effect will be studied in the afternoon, when the peak load occurs, using the IEEE 34 bus test feeder. First, only one spot node is used to charge the electric vehicles while a voltage regulator is present. Second, five spot nodes are loaded at the same time to charge the electric vehicles while voltage regulators are installed at each node. After that, the impact of electric vehicles on distribution feeders that do not have voltage regulators will appear.

  15. Effect of artificial feeders on pollen loads of the hummingbirds of Cerro de La Muerte, Costa Rica

    Directory of Open Access Journals (Sweden)

    Gerardo Avalos

    2012-03-01

    Full Text Available Although sugar-water feeders are commonly used by enthusiasts to attract hummingbirds, little is known about how they affect hummingbird behavior and flower use. We studied the highland hummingbird assemblage of Cerro de La Muerte, Costa Rica, both at a site with permanent feeders (La Georgina Restaurant and further from it. We examined how feeder use and monopolization affected seasonal changes in pollen loads during four sampling periods, including dry and wet seasons, from 2003-2005. We expected that species monopolizing the feeders would carry little or no pollen whatsoever, and would have pollen loads characterized by low floral diversity, in contrast with species less dependent on feeders. We obtained pollen samples from 183 individuals of four hummingbird species captured around the feeders using mist nets, which were compared with a pollen reference collection of plants with a pollination syndrome by hummingbirds. The same methods were implemented at a site 3km away from the feeders. Feeder usage was quantified by counting the number of times hummingbirds drank from the feeders in periods of 4min separated by 1min. The effects of hummingbird species and season on pollen load categories were assessed using a nominal logistic regression. The alpha species at the site, the Fiery-throated Hummingbird (Panterpe insignis, dominated the feeders during the dry season. Meanwhile, in the wet season, feeder usage was more evenly distributed across species, with the exception of the Volcano Hummingbird, Selasphorus flammula, which occupies the last place in the dominance hierarchy. Pollen loads of hummingbirds captured near feeders were low in abundance (more than 50% of captured individuals had zero or low pollen loads, and low in species richness (96% of the hummingbirds with pollen from only one plant genus, Centropogon. Overall pollen loads increased during the dry season coinciding with peaks in flower availability, although the majority of

  16. Effect of artificial feeders on pollen loads of the hummingbirds of Cerro de la Muerte, Costa Rica.

    Science.gov (United States)

    Avalos, Gerardo; Soto, Alejandra; Alfaro, Willy

    2012-03-01

    Although sugar-water feeders are commonly used by enthusiasts to attract hummingbirds, little is known about how they affect hummingbird behavior and flower use. We studied the highland hummingbird assemblage of Cerro de La Muerte, Costa Rica, both at a site with permanent feeders (La Georgina Restaurant) and further from it. We examined how feeder use and monopolization affected seasonal changes in pollen loads during four sampling periods, including dry and wet seasons, from 2003-2005. We expected that species monopolizing the feeders would carry little or no pollen whatsoever, and would have pollen loads characterized by low floral diversity, in contrast with species less dependent on feeders. We obtained pollen samples from 183 individuals of four hummingbird species captured around the feeders using mist nets, which were compared with a pollen reference collection of plants with a pollination syndrome by hummingbirds. The same methods were implemented at a site 3km away from the feeders. Feeder usage was quantified by counting the number of times hummingbirds drank from the feeders in periods of 4min separated by 1min. The effects of hummingbird species and season on pollen load categories were assessed using a nominal logistic regression. The alpha species at the site, the Fiery-throated Hummingbird (Panterpe insignis), dominated the feeders during the dry season. Meanwhile, in the wet season, feeder usage was more evenly distributed across species, with the exception of the Volcano Hummingbird, Selasphorus flammula, which occupies the last place in the dominance hierarchy. Pollen loads of hummingbirds captured near feeders were low in abundance (more than 50% of captured individuals had zero or low pollen loads), and low in species richness (96% of the hummingbirds with pollen from only one plant genus, Centropogon). Overall pollen loads increased during the dry season coinciding with peaks in flower availability, although the majority of captured

  17. Reducing cardiovascular risk factors in non-selected outpatients with schizophrenia.

    Science.gov (United States)

    Hansen, Mette Vinther; Hjorth, Peter; Kristiansen, Christina Blanner; Vandborg, Kirsten; Gustafsson, Lea Nørgaard; Munk-Jørgensen, Povl

    2016-06-01

    Cardiovascular diseases are the most common causes of premature death in patients with schizophrenia. We aimed at reducing cardiovascular risk factors in non-selected outpatients with schizophrenia using methods proven effective in short-term trials. Furthermore, we examined whether any baseline characteristics were associated with positive outcomes. All outpatients treated for schizophrenia at two Danish hospitals were included in this 1-year follow-up study. The patients were offered health interventions both individually and in groups. Weight, waist circumference, blood glucose, serum lipids, and information on smoking and alcohol were obtained. On average, small significant increases in body mass index (BMI) and waist circumferences were observed while small non-significant improvements in other cardiovascular risk factors were seen. Patients with high baseline BMI and patients with duration of treated illness beyond 2 years had significantly better intervention outcomes. Our results show that it was difficult to improve physical health in a group of non-selected patients with schizophrenia as part of routine care. The patients were not easily motivated to participate in the interventions, and it was difficult to monitor the recommended metabolic risk measures in the patient group. Future research should focus on simple strategies in health promotion that can be integrated into routine care. © The Author(s) 2016.

  18. A feeder protection method against the phase-phase fault using symmetrical components

    DEFF Research Database (Denmark)

    Ciontea, Catalin-Iosif; Bak, Claus Leth; Blaabjerg, Frede

    2017-01-01

    generation and relatively reduced short-circuit currents, thus resembling the electric network on a ship. The simulation results demonstrate that the proposed method of protection provides an improved performance compared to the conventional OverCurrent relays in a radial feeder with variable short......The method of symmetrical components simplifies analysis of an electric circuit during the fault and represents an important tool for the protection engineers. In this paper, the symmetrical components of the fault current are used in a new feeder protection method for the maritime applications...

  19. The impact of small benthic passive suspension feeders in shallow marine ecosystems: the hydroids as an example

    NARCIS (Netherlands)

    Gili, J.-M.; Alvà, V.; Coma, R.; Orejas, C.; Pagès, F.; Ribes, M.; Zabala, M.; Arntz, W.; Bouillon, J.; Boero, F.; Hughes, R.G.

    1998-01-01

    Benthic suspension feeders are abundant in littoral and shallow sub-littoral ecosystems, where they feed on the plankton and on organic matter suspended in the water column. Recent studies indicate that active suspension feeders with powerful water filtration mechanisms (e.g., bivalve molluscs) may

  20. Fetal biometric parameters: Reference charts for a non-selected risk population from Uberaba, Brazil.

    Science.gov (United States)

    Peixoto, Alberto Borges; da Cunha Caldas, Taciana Mara Rodrigues; Dulgheroff, Fernando Felix; Martins, Wellington P; Araujo Júnior, Edward

    2017-03-01

    To establish reference charts for fetal biometric parameters in a non-selected risk population from Uberaba, Southeast of Brazil. A retrospective cross-sectional study was performed among 5656 non-selected risk singleton pregnant women between 14 and 41 weeks of gestation. The ultrasound exams were performed during routine visits of second and third trimesters. Biparietal diameter (BPD) was measured at the level of the thalami and cavum septi pellucidi. Head circumference (HC) was calculated by the following formula: HC = 1.62*(BPD + occipital frontal diameter, OFD). Abdominal circumference (AC) was measured using the following formula: AC = (anteroposterior diameter + transverse abdominal diameter) × 1.57. Femur diaphysis length (FDL) was obtained in the longest axis of femur without including the distal femoral epiphysis. The estimated fetal weight (EFW) was obtained by the Hadlock formula. Polynomial regressions were performed to obtain the best-fit model for each fetal biometric parameter as the function of gestational age (GA). The mean, standard deviations ( SD ), minimum and maximum of BPD (cm), HC (cm), AC (cm), FDL (cm) and EFW (g) were 6.9 ± 1.9 (2.3 - 10.5), 24.51 ± 6.61 (9.1 - 36.4), 22.8 ± 7.3 (7.5 - 41.1), 4.9 ± 1.6 (1.2 - 8.1) and 1365 ± 1019 (103 - 4777), respectively. Second-degree polynomial regressions between the evaluated parameters and GA resulted in the following formulas: BPD = -4.044 + 0.540 × GA - 0.0049 × GA 2 ( R 2 = 0.97); HC= -15.420 + 2.024 GA - 0.0199 × GA 2 ( R 2 = 0.98); AC = -9.579 + 1.329 × GA - 0.0055 × GA 2 ( R 2 = 0.97); FDL = -3.778 + 0.416 × GA - 0.0035 × GA 2 ( R 2 = 0.98) and EFW = 916 - 123 × GA + 4.70 × GA 2 ( R 2 = 0.96); respectively. Reference charts for the fetal biometric parameters in a non-selected risk population from Uberaba, Southeast of Brazil, were established.

  1. Fetal biometric parameters: Reference charts for a non-selected risk population from Uberaba, Brazil

    Directory of Open Access Journals (Sweden)

    Alberto Borges Peixoto

    2017-03-01

    Full Text Available Objective: To establish reference charts for fetal biometric parameters in a non-selected risk population from Uberaba, Southeast of Brazil. Methods: A retrospective cross-sectional study was performed among 5656 non-selected risk singleton pregnant women between 14 and 41 weeks of gestation. The ultrasound exams were performed during routine visits of second and third trimesters. Biparietal diameter (BPD was measured at the level of the thalami and cavum septi pellucidi. Head circumference (HC was calculated by the following formula: HC = 1.62*(BPD + occipital frontal diameter, OFD. Abdominal circumference (AC was measured using the following formula: AC = (anteroposterior diameter + transverse abdominal diameter × 1.57. Femur diaphysis length (FDL was obtained in the longest axis of femur without including the distal femoral epiphysis. The estimated fetal weight (EFW was obtained by the Hadlock formula. Polynomial regressions were performed to obtain the best-fit model for each fetal biometric parameter as the function of gestational age (GA. Results: The mean, standard deviations (SD, minimum and maximum of BPD (cm, HC (cm, AC (cm, FDL (cm and EFW (g were 6.9 ± 1.9 (2.3 – 10.5, 24.51 ± 6.61 (9.1 – 36.4, 22.8 ± 7.3 (7.5 – 41.1, 4.9 ± 1.6 (1.2 – 8.1 and 1365 ± 1019 (103 – 4777, respectively. Second-degree polynomial regressions between the evaluated parameters and GA resulted in the following formulas: BPD = –4.044 + 0.540 × GA – 0.0049 × GA² (R² = 0.97; HC= –15.420 + 2.024 GA – 0.0199 × GA² (R² = 0.98; AC = –9.579 + 1.329 × GA – 0.0055 × GA² (R² = 0.97; FDL = –3.778 + 0.416 × GA – 0.0035 × GA² (R² = 0.98 and EFW = 916 – 123 × GA + 4.70 × GA² (R² = 0.96; respectively. Conclusion: Reference charts for the fetal biometric parameters in a non-selected risk population from Uberaba, Southeast of Brazil, were established.

  2. BSL-3 laboratory practices in the United States: comparison of select agent and non-select agent facilities.

    Science.gov (United States)

    Richards, Stephanie L; Pompei, Victoria C; Anderson, Alice

    2014-01-01

    New construction of biosafety level 3 (BSL-3) laboratories in the United States has increased in the past decade to facilitate research on potential bioterrorism agents. The Centers for Disease Control and Prevention inspect BSL-3 facilities and review commissioning documentation, but no single agency has oversight over all BSL-3 facilities. This article explores the extent to which standard operating procedures in US BSL-3 facilities vary between laboratories with select agent or non-select agent status. Comparisons are made for the following variables: personnel training, decontamination, personal protective equipment (PPE), medical surveillance, security access, laboratory structure and maintenance, funding, and pest management. Facilities working with select agents had more complex training programs and decontamination procedures than non-select agent facilities. Personnel working in select agent laboratories were likely to use powered air purifying respirators, while non-select agent laboratories primarily used N95 respirators. More rigorous medical surveillance was carried out in select agent workers (although not required by the select agent program) and a higher level of restrictive access to laboratories was found. Most select agent and non-select agent laboratories reported adequate structural integrity in facilities; however, differences were observed in personnel perception of funding for repairs. Pest management was carried out by select agent personnel more frequently than non-select agent personnel. Our findings support the need to promote high quality biosafety training and standard operating procedures in both select agent and non-select agent laboratories to improve occupational health and safety.

  3. Can non-selective beta-blockers prevent hepatocellular carcinoma in patients with cirrhosis?

    DEFF Research Database (Denmark)

    Thiele, Maja; Wiest, Reiner; Gluud, Lise Lotte

    2013-01-01

    Hepatocellular carcinoma is the main liver-related cause of death in patients with compensated cirrhosis. The early phases are asymptomatic and the prognosis is poor, which makes prevention essential. We propose that non-selective beta-blockers decrease the incidence and growth of hepatocellular...... and growth of hepatocellular carcinoma. Rodent and in vitro studies support the hypothesis, but clinical verification is needed. Different study designs may be considered. The feasibility of a randomized controlled trial is limited due to the necessary large number of patients and long follow......-up. Observational studies carry a high risk of bias. The meta-analytic approach may be used if the incidence and mortality of hepatocellular carcinoma can be extracted from trials on variceal bleeding and if the combined sample size and follow up is sufficient....

  4. Optimalisatie performance van vleeskuikens bij mobiel voer- en drinksysteem (scanFeeder) op praktijkbedrijf

    NARCIS (Netherlands)

    Harn, van J.; Veldkamp, T.

    2007-01-01

    Het gebruik van de Ridder ScanFeeder, een mobiel voer- en drinksysteem met strooiselbeluchting voor vleeskuikens, geeft een betere strooiselkwaliteit (ruller en droger strooisel) en minder voetzoolaandoeningen. De technische resultaten bij dit systeem blijven echter achter bij die van een

  5. Hybrid RSOA and fibre raman amplified long reach feeder link for WiMAX-on-fibre

    DEFF Research Database (Denmark)

    Amaya Fernández, Ferney Orlando; Martinez, Javier; Yu, Xianbin

    2009-01-01

    A distributed fibre Raman amplified long reach optical access feeder link using a reflective semiconductor optical amplifier in the remote base station is experimentally demonstrated for supporting WiMAXover- fibre transmission. The measured values for the error vector magnitude for quadrature...

  6. Tits recognize the potential dangers of predators and harmless birds in feeder experiments

    Czech Academy of Sciences Publication Activity Database

    Tvardíková, Kateřina; Fuchs, R.

    2012-01-01

    Roč. 30, č. 1 (2012), s. 157-165 ISSN 0289-0771 Grant - others:AV ČR(CZ) IAA601410803 Institutional research plan: CEZ:AV0Z50070508 Keywords : feeders * predator recognition * risk Subject RIV: EH - Ecology, Behaviour Impact factor: 1.000, year: 2012 http://www.springerlink.com/content/2338033t30261604/fulltext.pdf

  7. Evolution of generic supporting conditions for feeders of 500 M We PHWR

    International Nuclear Information System (INIS)

    Prasad, K.H.; Gupta, K.N.; Bapat, C.N.; Sharma, V.K.; Mishra, R.; Soni, R.S.; Kushwaha, H.S.; Mahajan, S.C.; Kakodkar, A.

    1995-01-01

    Feeder piping consists of 784 number of closely spaced, inter-connected flexible pipes catering for large thermal and creep movements besides seismic and other loadings. The analytical strategy for evolving generic supporting conditions is outlined in this paper. (author). 4 refs., 7 figs

  8. Effects of an increasing filter feeder stock on larval abundance in the Oosterschelde estuary (SW Netherlands)

    NARCIS (Netherlands)

    Troost, Karin; Gelderman, Edzard; Kamermans, Pauline; Smaal, Aad C.; Wolff, Wim J.

    Predation by adult bivalves oil bivalve larvae has been suggested to reduce larval abundance in areas with high bivalve filter-feeder biomass. Although the occurrence of larviphagy is well-studied in the laboratory, its effects in the field have scarcely been studied. We studied larviphagy at

  9. Effects of an increasing filter feeder stock on larval abundance in the Oosterschelde estuary (SW Netherlands)

    NARCIS (Netherlands)

    Troost, K.; Gelderman, E.A.C.; Kamermans, P.; Smaal, A.C.; Wolff, W.

    2009-01-01

    Predation by adult bivalves on bivalve larvae has been suggested to reduce larval abundance in areas with high bivalve filter-feeder biomass. Although the occurrence of larviphagy is well-studied in the laboratory, its effects in the field have scarcely been studied. We studied larviphagy at

  10. Feeder Cell Type Affects the Growth of In Vitro Cultured Bovine Trophoblast Cells

    Directory of Open Access Journals (Sweden)

    Islam M. Saadeldin

    2017-01-01

    Full Text Available Trophectoderm cells are the foremost embryonic cells to differentiate with prospective stem-cell properties. In the current study, we aimed at improving the current approach for trophoblast culture by using granulosa cells as feeders. Porcine granulosa cells (PGCs compared to the conventional mouse embryonic fibroblasts (MEFs were used to grow trophectoderm cells from hatched bovine blastocysts. Isolated trophectoderm cells were monitored and displayed characteristic epithelial/cuboidal morphology. The isolated trophectoderm cells expressed mRNA of homeobox protein (CDX2, cytokeratin-8 (KRT8, and interferon tau (IFNT. The expression level was higher on PGCs compared to MEFs throughout the study. In addition, primary trophectoderm cell colonies grew faster on PGCs, with a doubling time of approximately 48 hrs, compared to MEFs. PGCs feeders produced a fair amount of 17β-estradiol and progesterone. We speculated that the supplementation of sex steroids and still-unknown factors during the trophoblasts coculture on PGCs have helped to have better trophectoderm cell’s growth than on MEFs. This is the first time to use PGCs as feeders to culture trophectoderm cells and it proved superior to MEFs. We propose PGCs as alternative feeders for long-term culture of bovine trophectoderm cells. This model will potentially benefit studies on the early trophoblast and embryonic development in bovines.

  11. The effect of stocking density and bin feeder space on performance ...

    African Journals Online (AJOL)

    Unknown

    The effect of stocking density and bin feeder space on performance in pigs. G.A. Lavers# and N.S. Ferguson. School of Agricultural Sciences & Agribusiness, University of Natal, P Bag X01, Scottsville 3209. #Email: lavers@agric.unp.ac.za. Introduction. Pigs housed individually have been shown to have higher feed intakes ...

  12. The effect of stocking density and bin feeder space on performance ...

    African Journals Online (AJOL)

    The effect of stocking density and bin feeder space on performance in pigs. G.A. Lavers, N.S. Ferguson. Abstract. (South African J of Animal Science, 2000, 30, Supplement 1: 70-71). Full Text: EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT.

  13. Tumor Volume Decrease via Feeder Occlusion for Treating a Large, Firm Trigone Meningioma.

    Science.gov (United States)

    Nakashima, Takuma; Hatano, Norikazu; Kanamori, Fumiaki; Muraoka, Shinsuke; Kawabata, Teppei; Takasu, Syuntaro; Watanabe, Tadashi; Kojima, Takao; Nagatani, Tetsuya; Seki, Yukio

    2018-01-01

    Trigone meningiomas are considered a surgical challenge, as they tend to be considerably large and hypervascularized at the time of presentation. We experienced a case of a large and very hard trigone meningioma that was effectively treated using initial microsurgical feeder occlusion followed by surgery in stages. A 19-year-old woman who presented with loss of consciousness was referred to our hospital for surgical treatment of a brain tumor. Radiological findings were compatible with a left ventricular trigone meningioma extending laterally in proximity to the Sylvian fissure. At initial surgery using the transsylvian approach, main feeders originating from the anterior and lateral posterior choroidal arteries were occluded at the inferior horn; however, only a small section of the tumor could initially be removed because of its firmness. Over time, feeder occlusion resulted in tumor necrosis and a 20% decrease in its diameter; the mass effect was alleviated within 1 year. The residual meningioma was then totally excised in staged surgical procedures after resection became more feasible owing to ischemia-induced partial softening of the tumor. When a trigone meningioma is large and very hard, initial microsurgical feeder occlusion in the inferior horn can be a safe and effective option, and can lead to necrosis, volume decrease, and partial softening of the residual tumor to allow for its staged surgical excision.

  14. Operation of a cell feeder for coal controlled by a frequency converter. [Czechoslovakia

    Energy Technology Data Exchange (ETDEWEB)

    Stonawski, J; Sikora, G

    1984-02-01

    Steam boiler of the Trinec coal-fired power plant with a capacity of 125 t/h, 545 C, 9.5 MPa was equipped with a screw coal feeder with the KT26A-6 Winter-Eichberg motor with a transformer. The screw fee

  15. Co-ordination of directional overcurrent protection with load current for parallel feeders

    Energy Technology Data Exchange (ETDEWEB)

    Wright, J.W.; Lloyd, G.; Hindle, P.J. [Alstom, Inc., Stafford (United Kingdom). T and D Protection and Control

    1999-11-01

    Directional phase overcurrent relays are commonly applied at the receiving ends of parallel feeders or transformer feeders. Their purpose is to ensure full discrimination of main or back-up power system overcurrent protection for a fault near the receiving end of one feeder. This paper reviews this type of relay application and highlights load current setting constraints for directional protection. Such constraints have not previously been publicized in well-known text books. A directional relay current setting constraint that is suggested in some text books is based purely on thermal rating considerations for older technology relays. This constraint may not exist with modern numerical relays. In the absence of any apparent constraint, there is a temptation to adopt lower current settings with modern directional relays in relation to reverse load current at the receiving ends of parallel feeders. This paper identifies the danger of adopting very low current settings without any special relay feature to ensure protection security with load current during power system faults. A system incident recorded by numerical relays is also offered to highlight this danger. In cases where there is a need to infringe the identified constraints an implemented and testing relaying technique is proposed.

  16. A Branch-and-Price Approach to the Feeder Network Design Problem

    DEFF Research Database (Denmark)

    Santini, Alberto; Plum, Christian Edinger Munk; Røpke, Stefan

    2017-01-01

    In this paper we consider the problem of designing a container liner shipping feeder network. The designer has to choose which port to serve during many rotations that start and end at a central hub. Many operational characteristics are considered, such as variable leg-by-leg speeds and cargo...

  17. harmonic load modeling: a case study of 33 kv abuja steel mill feeder

    African Journals Online (AJOL)

    HOD

    An in-depth study of the harmonic orders inherent in a power system network is required ... This paper studied the harmonic orders of the 33 kV Abuja Steel Feeder .... models for various industrial and household electrical ..... Malaysia, 2013.

  18. Optimal Design of the Feeder-Bus Network Based on the Transfer System

    Directory of Open Access Journals (Sweden)

    Lianbo Deng

    2013-01-01

    Full Text Available This paper studied the classic feeder-bus network design problem (FBNDP, which can be described as follows: for the passenger travel demand between rail stations and bus stops on a given urban transit network, it designs the optimal feeder bus routes and frequencies so as to minimize the passengers’ travel expense and the operator’s cost. We extended the demand pattern of M-to-1 in most existing researches to M-to-M. We comprehensively considered the passenger travel cost, which includes the waiting and riding cost on the bus, riding cost on rail, and transfer cost between these two transportation modes, and presented a new genetic algorithm that determines the optimal feeder-bus operating frequencies under strict constraint conditions. The numerical examples under different demand patterns have been experienced and analysed, which showed the robustness and efficiency of the presented algorithm. We also found that the distribution pattern of the travel demand has a significant influence on the feeder-bus network construction.

  19. BC Hydro's integrated approach on replacing underground feeder cables

    Energy Technology Data Exchange (ETDEWEB)

    Tarampi, D. [BC Hydro, Burnaby, BC (Canada)

    2008-07-01

    BC Hydro's integrated approach on replacing underground feeder cables was discussed. The feeder cables were all in ducts encased in concrete and splices were identified in concrete manholes. The feeder cables averaged 35 to 40 failures per year, with a large majority of failures occurring in manholes or near terminations. The age of the cables was not known. A graphical representation of a condition assessment was presented with reference to an electrical test, metallurgical test, hardness test, and dye penetrating test. Prioritization steps were also listed, including a condition index and replacement threshold. Steps in prioritizing the condition index included determining the insulation index based on electrical test results; determining the manhole condition based on metallurgical test results; determining the customer importance factor and feeder load factor; and calculating the overall condition index based on the indices. A process flowchart was also illustrated. A replacement strategy was then discussed and a cost comparison of two options was described. Option 1 was to replace only the unjacketed cables while option two involved selective replacement. tabs., figs.

  20. Effects of different feeder layers on culture of bovine embryonic stem cell-like cells in vitro.

    Science.gov (United States)

    Cong, Shan; Cao, Guifang; Liu, Dongjun

    2014-12-01

    To find a suitable feeder layer is important for successful culture conditions of bovine embryonic stem cell-like cells. In this study, expression of pluripotency-related genes OCT4, SOX2 and NANOG in bovine embryonic stem cell-like cells on mouse embryonic fibroblast feeder layers at 1-5 passages were monitored in order to identify the possible reason that bovine embryonic stem cell-like cells could not continue growth and passage. Here, we developed two novel feeder layers, mixed embryonic fibroblast feeder layers of mouse and bovine embryonic fibroblast at different ratios and sources including mouse fibroblast cell lines. The bovine embryonic stem cell-like cells generated in our study displayed typical stem cell morphology and expressed specific markers such as OCT4, stage-specific embryonic antigen 1 and 4, alkaline phosphatase, SOX2, and NANOG mRNA levels. When feeder layers and cell growth factors were removed, the bovine embryonic stem cell-like cells formed embryoid bodies in a suspension culture. Furthermore, we compared the expression of the pluripotent markers during bovine embryonic stem cell-like cell in culture on mixed embryonic fibroblast feeder layers, including mouse fibroblast cell lines feeder layers and mouse embryonic fibroblast feeder layers by real-time quantitative polymerase chain reaction. Results suggested that mixed embryonic fibroblast and sources including mouse fibroblast cell lines feeder layers were more suitable for long-term culture and growth of bovine embryonic stem cell-like cells than mouse embryonic fibroblast feeder layers. The findings may provide useful experimental data for the establishment of an appropriate culture system for bovine embryonic stem cell lines.

  1. Impact of feeder space on laying hen feeding behavior and production performance in enriched colony housing.

    Science.gov (United States)

    Oliveira, J L; Xin, H; Wu, H

    2018-05-30

    Current feeder space recommendations in laying hen welfare guidelines are inconsistent among and within countries. One determining criterion forming the recommendations (e.g. 12.0 cm/hen for the EU guideline) is that all birds can feed simultaneously. However, if there are other resources in the environment, as in enriched colony housing (ECH), it is unknown whether group-housed hens will choose to feed simultaneously. This study assesses the impact of feeder space on feeding behavior of 60 laying hens (W-36) in ECH using a ultra-high frequency radio-frequency identification-based tracking system. The feeder spaces investigated were 12.0, 9.5, 8.5 and 6.5 cm/hen, achieved by blocking portions of the overall feeder access to keep hens at the same stocking density. Each feeder space treatment, randomly assigned over the course of the experiment, lasted for 7 consecutive days. Feeding behaviors were characterized as daily time spent at the feeder (TS, min/hen-day), daily frequency of visits to the feeder (FV, #/hen-day), and maximum or average percentage of hens feeding simultaneously (MPB, APB, %). Group-average daily feed intake (FI, g/hen-day), water use (WU, g/hen-day), and hen-day egg production (HDEP, %) were also measured. The results revealed that at 12.0 cm/hen, where unoccupied feeder space was present, a maximum of 59.0±1.4% (average of 31.7±0.3%) hens fed simultaneously. No significant differences were detected among 12.0, 9.5 and 8.5 cm/hen in TS (293±10, 286±10 and 281±10 min/hen-day) and MPB (59.0±1.4, 57.3±1.4 and 53.3±1.4%) (P>0.05). The outcome of no significant differences also held true between 12.0 and 9.5 cm/hen in APB (31.7±0.3 v. 30.8±0.3%) and between 9.5 and 8.5 cm/hen in all response variables measured (P>0.05). However, there were significant differences in APB between 6.5 cm/hen and all other treatments; in TS and FV between 6.5 and 9.5 cm/hen; and in MPB between 6.5 and 12 cm/hen (P0.05). The results revealed that synchronous

  2. The Use of Filter-feeders to Manage Disease in a Changing World.

    Science.gov (United States)

    Burge, Colleen A; Closek, Collin J; Friedman, Carolyn S; Groner, Maya L; Jenkins, Cody M; Shore-Maggio, Amanda; Welsh, Jennifer E

    2016-10-01

    Rapid environmental change is linked to increases in aquatic disease heightening the need to develop strategies to manage disease. Filter-feeding species are effective biofilters and can naturally mitigate disease risk to humans and wildlife. We review the role of filter-feeders, with an emphasis on bivalves, in altering disease outcomes via augmentation and reduction. Filtration can reduce transmission by removing pathogens from the water column via degradation and release of pathogens in pseudofeces. In other cases, filtration can increase pathogen transmission and disease risk. The effect of filtration on pathogen transmission depends on the selectivity of the filter-feeder, the degree of infectivity by the pathogen, the mechanism(s) of pathogen transmission and the ability of the pathogen to resist degradation. For example, some bacteria and viruses can resist degradation and accumulate within a filter-feeder leading to disease transmission to humans and other wildlife upon ingestion. Since bivalves can concentrate microorganisms, they are also useful as sentinels for the presence of pathogenic microorganisms. While somewhat less studied, other invertebrates, including ascidians and sponges may also provide ecosystem services by altering pathogen transmission. In all scenarios, climate change may affect the potential for filter-feeders to mitigate disease risk. We conclude that an assessment including empirical data and modeling of system-wide impacts should be conducted before selection of filter-feeders to mitigate disease. Such studies should consider physiology of the host and microbe and risk factors for negative impacts including augmentation of other pathogens. © The Author 2016. Published by Oxford University Press on behalf of the Society for Integrative and Comparative Biology. All rights reserved. For permissions please email: journals.permissions@oup.com.

  3. A reliable and economical method for gaining mouse embryonic fibroblasts capable of preparing feeder layers.

    Science.gov (United States)

    Jiang, Guangming; Wan, Xiaoju; Wang, Ming; Zhou, Jianhua; Pan, Jian; Wang, Baolong

    2016-08-01

    Mouse embryonic fibroblasts (MEFs) are widely used to prepare feeder layers for culturing embryonic stem cells (ESCs) or induced pluripotent stem cells (iPSCs) in vitro. Transportation lesions and exorbitant prices make the commercially obtained MEFs unsuitable for long term research. The aim of present study is to establish a method, which enables researchers to gain MEFs from mice and establish feeder layers by themselves in ordinary laboratories. MEFs were isolated from ICR mouse embryos at 12.5-17.5 day post-coitum (DPC) and cultured in vitro. At P2-P7, the cells were inactivated with mitomycin C or by X-ray irradiation. Then they were used to prepare feeder layers. The key factors of the whole protocol were analyzed to determine the optimal conditions for the method. The results revealed MEFs isolated at 12.5-13.5 DPC, and cultured to P3 were the best choice for feeder preparation, those P2 and P4-P5 MEFs were also suitable for the purpose. The P3-P5 MEFs treated with 10 μg/ml of mitomycin C for 3 h, or irradiated with X-ray at 1.5 Gy/min for 25 Gy were the most suitable feeder cells. Treating MEFs with 10 μg/ml of mitomycin C for 2.5 h, 15 μg/ml for 2.0 h, or irradiating the cells with 20 Gy of X-ray at 2.0 Gy/min could all serve as alternative methods for P3-P4 cells. Our study provides a reliable and economical way to obtain large amount of qualified MEFs for long term research of ESCs or iPSCs.

  4. Mass transfer effects in feeder flow-accelerated corrosion wall thinning

    International Nuclear Information System (INIS)

    Pietralik, J.

    2008-01-01

    Flow conditions play a dominant role in Flow-Accelerated Corrosion (FAC) under certain conditions, e.g., in CANDU feeders. While chemistry and materials set the overall potential for FAC, flow conditions determine the local distribution of wall thinning. Recent plant data of feeders and laboratory tests confirms that there is a close relationship between local flow conditions, expressed by mass transfer coefficient, and FAC rate in CANDU feeder bends. The knowledge of local effects can be useful for minimizing the number of inspected components, predicting the location of the highest FAC rate for a given piping component, and determining what components or feeders should be replaced. A similar evaluation applies also to FAC in heat transfer equipment such as heat exchangers and steam generators. The objective of this paper is to examine the relationship between FAC rate and local mass transfer parameters. For FAC where the flow is dominant, the FAC rate is proportional to mass flux of ferrous ions. The mass flux is the product of the mass transfer coefficient and the concentration difference, or degree of saturation. The mass transfer coefficient describes the intensity of the transport of corrosion products (ferrous ions) from the oxide-water interface into the bulk water. Therefore, this parameter can be used for predicting the local distribution of FAC rate in the mass-transfer controlled FAC. The degree of saturation reduces the mass flux, thus reducing the FAC rate. This effect can be significant in long piping, e.g., in outlet feeders. The paper presents plant and laboratory evidence for the relationship between local mass transfer conditions and the FAC rate. It shows correlations for mass transfer coefficient in components that are highly susceptible to FAC and most important flow parameters that affect mass transfer coefficient. The role of surface roughness, wall shear stress, and local turbulence is also discussed. (author)

  5. Real-Time Distribution Feeder Performance Monitoring, Advisory Control, and Health Management System

    Energy Technology Data Exchange (ETDEWEB)

    Stoupis, James; Mousavi, Mirrasoul

    2014-09-30

    New data collection system equipment was installed in Xcel Energy substations and data was collected from 6 substations and 20 feeders. During Phase I, ABB collected and analyzed 793 real-time events to date from 6 Xcel Energy substations and continues today. The development and integration of several applications was completed during the course of this project, including a model-based faulted segment identification algorithm, with very positive results validated with field-gathered data discussed and included in this report. For mostly underground feeders, the success rate is 90% and the overreach rate is 90%. For mostly overhead feeders, the success rate is 74% and the overreach rate is 50%. The developed method is producing very accurate results for mostly underground feeders. For mostly overhead feeders, due to the bad OMS data quality and varying fault resistance when arcing, the developed method is producing good results but with much room for improvement. One area where the algorithm can be improved is the accuracy for sub-cycle fault events. In these cases, the accuracy of the conventional signal processing methods suffers due to most of these methods being based on a one-cycle processing window. By improving the signal processing accuracy, the accuracy of the faulted segment identification algorithm will also improve significantly. ABB intends to devote research in this area in the near future to help solve this problem. Other new applications developed during the course of the project include volt/VAR monitoring, unbalanced capacitor switching detection, unbalanced feeder loading detection, and feeder overloading detection. An important aspect of the demonstration phase of the project is to show the ability to provide adequate “heads-up” time ahead of customer calls or AMI reports so that the operators are provided with the much needed time to collect information needed to address an outage. The advance notification feature of the demonstration system

  6. [Problems of cardiovascular toxicity of coxibs and non-selective NSA].

    Science.gov (United States)

    Forejtová, S

    2006-01-01

    Non-steroidal antirheumatics (NSA) belong to the most often prescribed drugs. Certain observation studies indicate that they are used by 20 to 30% of population of developed countries. The most common NSA's adverse effects are gastrointestinal complications. Coxibs have been developed as an alternative to conventional non-selective NSA; with similar efficacy, they should reduce the risk of development of gastrointestinal complications. In the few last years, possible toxicity of coxibs and other non-steroidal antirheumatics has been widely discussed. The VIGOR study, which was performed 6 years ago, showed five times higher incidence of nonfatal myocardial infarction in patients with rofecoxib therapy as compared with naproxen. Afterwards, there was much debate about rofecoxib, and coxibs in general, whose cardiotoxicity was supported and confuted at the same time. Possible cardioprotective effect of naproxen was discussed too. Later on, results of the APPROVE study (Adenoma Polyp Prevention on Vioxx) made Merck & Co., Inc. withdraw rofecoxib from all markets voluntarily. In the end of 2004, three controversial studies on celecoxib were published. Although the first study (Adenoma Prevention with Celecoxib study, APC) showed higher cardiovascular risk of celecoxib, the second study (Prevention of Adenomatosus Polyps, PreSAP) did not verify these results. Surprisingly, the third study (Alzheimer Disease and Prevention Trial, ADAPT) proved 50% increase of the risk of cardiovascular (CV) toxicity of naproxen. In the last year, researchers have tried to decide whether CV toxicity is a class effect of coxib group or a class effect of all NSA. Many observation studies proved higher CV risk both of coxibs (particularly rofecoxib) and non-selective NSA including naproxen. These new findings moved the American FDA (Food and Drug Administration) to publish guidance concerning higher CV risk of all coxibs and NSA. For the time being, the EMEA (European Agency for Evaluation

  7. Effects of different feeder layers on culture of bovine embryonic stem cell-like cells in vitro

    OpenAIRE

    Cong, Shan; Cao, Guifang; Liu, Dongjun

    2014-01-01

    To find a suitable feeder layer is important for successful culture conditions of bovine embryonic stem cell-like cells. In this study, expression of pluripotency-related genes OCT4, SOX2 and NANOG in bovine embryonic stem cell-like cells on mouse embryonic fibroblast feeder layers at 1–5 passages were monitored in order to identify the possible reason that bovine embryonic stem cell-like cells could not continue growth and passage. Here, we developed two novel feeder layers, mixed embryonic ...

  8. A novel safety assessment strategy applied to non-selective extracts.

    Science.gov (United States)

    Koster, Sander; Leeman, Winfried; Verheij, Elwin; Dutman, Ellen; van Stee, Leo; Nielsen, Lene Munch; Ronsmans, Stefan; Noteborn, Hub; Krul, Lisette

    2015-06-01

    A main challenge in food safety research is to demonstrate that processing of foodstuffs does not lead to the formation of substances for which the safety upon consumption might be questioned. This is especially so since food is a complex matrix in which the analytical detection of substances, and consequent risk assessment thereof, is difficult to determine. Here, a pragmatic novel safety assessment strategy is applied to the production of non-selective extracts (NSEs), used for different purposes in food such as for colouring purposes, which are complex food mixtures prepared from reference juices. The Complex Mixture Safety Assessment Strategy (CoMSAS) is an exposure driven approach enabling to efficiently assess the safety of the NSE by focussing on newly formed substances or substances that may increase in exposure during the processing of the NSE. CoMSAS enables to distinguish toxicologically relevant from toxicologically less relevant substances, when related to their respective levels of exposure. This will reduce the amount of work needed for identification, characterisation and safety assessment of unknown substances detected at low concentration, without the need for toxicity testing using animal studies. In this paper, the CoMSAS approach has been applied for elderberry and pumpkin NSEs used for food colouring purposes. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. High-speed optical feeder-link system using adaptive optics

    Science.gov (United States)

    Arimoto, Yoshinori; Hayano, Yutaka; Klaus, Werner

    1997-05-01

    We propose a satellite laser communication system between a ground station and a geostationary satellite, named high- speed optical feeder link system. It is based on the application of (a) high-speed optical devices, which have been developed for ground-based high-speed fiber-optic communications, and (b) the adaptive optics which compensates wavefront distortions due to atmospheric turbulences using a real time feedback control. A link budget study shows that a system with 10-Gbps bit-rate are available assuming the state-of-the-art device performance of the Er-doped fiber amplifier. We further discuss preliminary measurement results of the atmospheric turbulence at the telescope site in Tokyo, and present current study on the design of the key components for the feeder-link laser transceiver.

  10. The effects of automated scatter feeders on captive grizzly bear activity budgets.

    Science.gov (United States)

    Andrews, Nathan L P; Ha, James C

    2014-01-01

    Although captive bears are popular zoo attractions, they are known to exhibit high levels of repetitive behaviors (RBs). These behaviors have also made them particularly popular subjects for welfare research. To date, most research on ursid welfare has focused on various feeding methods that seek to increase time spent searching for, extracting, or consuming food. Prior research indicates an average of a 50% reduction in RBs when attempts are successful and, roughly, a 50% success rate across studies. This research focused on decreasing time spent in an RB while increasing the time spent active by increasing time spent searching for, extracting, and consuming food. The utility of timed, automated scatter feeders was examined for use with captive grizzly bears (Ursis arctos horribilis). Findings include a significant decrease in time spent in RB and a significant increase in time spent active while the feeders were in use. Further, the bears exhibited a wider range of behaviors and a greater use of their enclosure.

  11. Irradiated murine fibroblasts as feeder layer used in human cell culture

    International Nuclear Information System (INIS)

    Almeida, Tiago L.; Klingbeil, Fatima G.; Yoshito, Daniele; Caproni, Priscila; Mathor, Monica B.; Herson, Marisa R.

    2007-01-01

    In 1975, Rheinwald and Green published an in vitro model for keratinocyte cell cultures in which the use of murine fibroblasts, as a feeder layer was introduced. These cells are modified fibroblasts, which presence render keratinocyte cells to remain proliferative for longer periods of time. This optimization of culture outputs has allowed for several clinical applications of confluent keratinocyte cultures as skin substitutes or wound dressings in situations such as post burn extensive skin loss, loss of oral mucosa, and other skin disorders. Nevertheless, proliferation of fibroblast in co-culture with keratinocytes must be controlled by anti-proliferative measures such as irradiation; at the same time, keratinocytes require specific nutrients in the culture medium, which may interfere with the fibroblast feeder layer viability. Therefore, the thorough understanding of the impact of different issues such as culture media composition, irradiation dose and pre-plating storage conditions of irradiated fibroblast to be used as feeder layer in these co-culture systems is important. In this work, changes as far as viability and proliferative rates of irradiated fibroblasts in culture were evaluated in relation to the type of culture medium used, dose of gamma radiation exposure, storage and timing of cell plating post irradiation. Results indicate that the type of culture medium used and time-lag between irradiation, refrigeration and plating of irradiated cells do not have significant impact in culture outcomes. However, the dose of gamma radiation administered to the cells may influence the final quality of these cells if to be used as a feeder layer. (author)

  12. Feeder use predicts both acquisition and transmission of a contagious pathogen in a North American songbird.

    Science.gov (United States)

    Adelman, James S; Moyers, Sahnzi C; Farine, Damien R; Hawley, Dana M

    2015-09-22

    Individual heterogeneity can influence the dynamics of infectious diseases in wildlife and humans alike. Thus, recent work has sought to identify behavioural characteristics that contribute disproportionately to individual variation in pathogen acquisition (super-receiving) or transmission (super-spreading). However, it remains unknown whether the same behaviours enhance both acquisition and transmission, a scenario likely to result in explosive epidemics. Here, we examined this possibility in an ecologically relevant host-pathogen system: house finches and their bacterial pathogen, Mycoplasma gallisepticum, which causes severe conjunctivitis. We examined behaviours likely to influence disease acquisition (feeder use, aggression, social network affiliations) in an observational field study, finding that the time an individual spends on bird feeders best predicted the risk of conjunctivitis. To test whether this behaviour also influences the likelihood of transmitting M. gallisepticum, we experimentally inoculated individuals based on feeding behaviour and tracked epidemics within captive flocks. As predicted, transmission was fastest when birds that spent the most time on feeders initiated the epidemic. Our results suggest that the same behaviour underlies both pathogen acquisition and transmission in this system and potentially others. Identifying individuals that exhibit such behaviours is critical for disease management. © 2015 The Author(s).

  13. Urbanization affects neophilia and risk-taking at bird-feeders

    Science.gov (United States)

    Tryjanowski, Piotr; Møller, Anders Pape; Morelli, Federico; Biaduń, Waldemar; Brauze, Tomasz; Ciach, Michał; Czechowski, Paweł; Czyż, Stanisław; Dulisz, Beata; Goławski, Artur; Hetmański, Tomasz; Indykiewicz, Piotr; Mitrus, Cezary; Myczko, Łukasz; Nowakowski, Jacek J.; Polakowski, Michał; Takacs, Viktoria; Wysocki, Dariusz; Zduniak, Piotr

    2016-06-01

    Urban environments cover vast areas with a high density of humans and their dogs and cats causing problems for exploitation of new resources by wild animals. Such resources facilitate colonization by individuals with a high level of neophilia predicting that urban animals should show more neophilia than rural conspecifics. We provided bird-feeders across urban environments in 14 Polish cities and matched nearby rural habitats, testing whether the presence of a novel item (a brightly coloured green object made out of gum with a tuft of hair) differentially delayed arrival at feeders in rural compared to urban habitats. The presence of a novel object reduced the number of great tits Parus major, but also the total number of all species of birds although differentially so in urban compared to rural areas. That was the case independent of the potentially confounding effects of temperature, population density of birds, and the abundance of cats, dogs and pedestrians. The number of great tits and the total number of birds attending feeders increased in urban compared to rural areas independent of local population density of birds. This implies that urban birds have high levels of neophilia allowing them to readily exploit unpredictable resources in urban environments.

  14. Economic Contribution of Regional Feeder Ports to The Local Economy In Indonesia

    Directory of Open Access Journals (Sweden)

    Ibnu Syabri

    2017-07-01

    Full Text Available Indonesia regional feeder ports’ main function is to serve marine transport activities between regency/city in a province in limited quantities. The intention of the government to make marine transportation as the backbone of national logistic transportation system puts these ports to an important position, as suppliers for the main and/or collector ports and as goods distribution centers for the region from the bigger ports. Not only as a provider of accessibility between regions, regional feeder ports should be seen as an investation to boost regional economy. This study aims to explain the influences of regional feeder ports on regency/city economy, based on the port types: (1 cargo ports, and (2 cargo & passengers ports. Results showed that both types of ports have positive influences on the regency/city economy, although it is not related to region’s economic base sector. Cargo ports which are mainly located on west area of Indonesia, supports the region’s economy more than cargo & passenger ports which are mainly located on the east.

  15. Resolving the architecture of monogenetic feeder systems from exposures of extinct volcanic fields

    Science.gov (United States)

    Muirhead, J.; Van Eaton, A. R.; Re, G.; White, J. D. L.; Ort, M. H.

    2016-12-01

    Monogenetic volcanic fields pose hazards to a number of major cities worldwide. During an eruption, the evolution of the intrusive feeder network modulates eruption behavior and location, as well as the warning signs of impending activity. However, historical examples of monogenetic eruptions are rare, particularly those monitored with the modern tools required to constrain the geometry and interconnectivity of subsurface intrusive feeders (e.g., InSAR, GPS). Geologic exposures in extinct fields around the Colorado Plateau provide clues to the geometry of shallow intrusions (<1000 m depth) that feed monogenetic volcanoes. We present field- and satellite-based observations of exposed intrusions in the Hopi Buttes volcanic field (Arizona), which reveal that many eruptions were fed by interconnected dike-sill systems. Results from the Hopi Buttes show that volcanic cone alignment studies are biased to the identification of dike intrusions, and thereby neglect the important contributions of sills to shallow feeder systems. For example, estimates of intruded volumes in fields exhumed by uplift and erosion in Utah and Arizona show that sills make up 30 - 92% of the shallow intruded volume within 1000 m of the paleosurface. By transporting magma toward and away from eruptive conduits, these sills likely played a role in modulating eruption styles (e.g., explosive vs effusive) and controlling lateral vent migrations. Sill transitions at Hopi Buttes would have produced detectable surface uplifts, and illustrate the importance of geological studies for informing interpretations of geodetic and seismological data during volcanic crises.

  16. Manufacture and test of prototype water pipe chase barrier in ITER Magnet Feeder system

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Kun, E-mail: lukun@ipp.ac.cn [Institute of Plasma Physics, Shushan Hu Road 350, Hefei, Anhui (China); Wen, Xinjie; Liu, Chen; Song, Yuntao [Institute of Plasma Physics, Shushan Hu Road 350, Hefei, Anhui (China); Niu, Erwu [ITER China, 15B Fuxing Road, Beijing 100862 (China); Gung, Chenyu; Su, Man [ITER Organization, Route de Vinon-sur-Verdon – CS 90046, 13067 St Paul-lez-Durance Cedex (France)

    2016-11-01

    The Magnet Feeder system in the International Thermonuclear Experimental Reactor (ITER) deploys electrical currents and supercritical helium to the superconducting magnets and the magnet diagnostic signals to the operators. In the current design, the feeders located in the upper L3 level of the Tokamak gallery penetrate the Tokamak coolant water system vault, the biological shield and the cryostat. As a secondary confinement to contain the activated coolant water in the vault in the case of water pipe burst accident, a water barrier is welded between the penetration in the water pipe chase outer wall and the mid-plane of the vacuum jacket of the Feeder Coil Terminal Box (CTB). A thin-wall stainless steel diaphragm with an omega shape profile is welded around the CTB as the water barrier to endure 2 bar hydraulic pressure. In addition, the barrier is designed as a flexible compensator to withstand a maximum of 15 mm of axial displacement of the CTB in case of helium leak accident without failure. This paper presents the detail configuration, the manufacturing and assembly processes of the water barrier. Test results of the prototype water barrier under simulated accident conditions are also reported. Successful qualification of the design and manufacturing process of the water barrier lays a good foundation for the series production of this subsystem.

  17. Identification of molecules derived from human fibroblast feeder cells that support the proliferation of human embryonic stem cells

    DEFF Research Database (Denmark)

    Anisimov, Sergey V.; Christophersen, Nicolaj S.; Correia, Ana S.

    2011-01-01

    The majority of human embryonic stem cell lines depend on a feeder cell layer for continuous growth in vitro, so that they can remain in an undifferentiated state. Limited knowledge is available concerning the molecular mechanisms that underlie the capacity of feeder cells to support both...... the proliferation and pluripotency of these cells. Importantly, feeder cells generally lose their capacity to support human embryonic stem cell proliferation in vitro following long-term culture. In this study, we performed large-scale gene expression profiles of human foreskin fibroblasts during early...... foreskin fibroblasts to serve as feeder cells for human embryonic stem cell cultures. Among these, the C-KIT, leptin and pigment epithelium-derived factor (PEDF) genes were the most interesting candidates....

  18. Single-Molecule FISH Reveals Non-selective Packaging of Rift Valley Fever Virus Genome Segments.

    Directory of Open Access Journals (Sweden)

    Paul J Wichgers Schreur

    2016-08-01

    Full Text Available The bunyavirus genome comprises a small (S, medium (M, and large (L RNA segment of negative polarity. Although genome segmentation confers evolutionary advantages by enabling genome reassortment events with related viruses, genome segmentation also complicates genome replication and packaging. Accumulating evidence suggests that genomes of viruses with eight or more genome segments are incorporated into virions by highly selective processes. Remarkably, little is known about the genome packaging process of the tri-segmented bunyaviruses. Here, we evaluated, by single-molecule RNA fluorescence in situ hybridization (FISH, the intracellular spatio-temporal distribution and replication kinetics of the Rift Valley fever virus (RVFV genome and determined the segment composition of mature virions. The results reveal that the RVFV genome segments start to replicate near the site of infection before spreading and replicating throughout the cytoplasm followed by translocation to the virion assembly site at the Golgi network. Despite the average intracellular S, M and L genome segments approached a 1:1:1 ratio, major differences in genome segment ratios were observed among cells. We also observed a significant amount of cells lacking evidence of M-segment replication. Analysis of two-segmented replicons and four-segmented viruses subsequently confirmed the previous notion that Golgi recruitment is mediated by the Gn glycoprotein. The absence of colocalization of the different segments in the cytoplasm and the successful rescue of a tri-segmented variant with a codon shuffled M-segment suggested that inter-segment interactions are unlikely to drive the copackaging of the different segments into a single virion. The latter was confirmed by direct visualization of RNPs inside mature virions which showed that the majority of virions lack one or more genome segments. Altogether, this study suggests that RVFV genome packaging is a non-selective process.

  19. Replacement of murine fibroblasts by human fibroblasts irradiated in obtaining feeder layer for the culture of human keratinocytes

    International Nuclear Information System (INIS)

    Yoshito, Daniele; Sufi, Bianca S.; Santin, Stefany P.; Mathor, Monica B.; Altran, Silvana C.; Isaac, Cesar

    2011-01-01

    Human autologous epithelia cultivated in vitro, have been used successfully in treating damage to skin integrity. The methodology allowed the cultivation of these epithelia was described by Rheinwald and Green in 1975, this methodology consisted in seeding keratinocytes onto a feeder layer composed of lineage 3T3 murine fibroblasts, the proliferation rate is controlled through the action of ionizing radiation. However, currently there is a growing concern about the possibility of transmitting prions and murine viruses to transplanted patients. Taking into account this concern, in this present work, we replaced the feeder layer originally composed of murine fibroblasts by human fibroblasts. To obtain this new feeder layer was necessary to standardize the enough irradiation dose to inhibit the replication of human fibroblasts and the verification of effectiveness of the development of keratinocytes culture on a feeder layer thus obtained. According to the obtained results we can verify that the human fibroblasts irradiated at various tested doses (60, 70, 100, 200, 250 and 300 Gy) had their mitotic activity inactivated by irradiation, allowing the use of any of these doses to confection of the feeder layer, since these fibroblasts irradiated still showed viable until fourteen days of cultivation. In the test of colony formation efficiency was observed that keratinocytes seeded on irradiated human fibroblasts were able to develop satisfactorily, preserving their clonogenic potential. Therefore it was possible the replacement of murine fibroblasts by human fibroblasts in confection of the feeder layer, in order to eliminate this xenobiotic component of the keratinocytes culture. (author)

  20. Fabrication of corneal epithelial cell sheets maintaining colony-forming cells without feeder cells by oxygen-controlled method.

    Science.gov (United States)

    Nakajima, Ryota; Takeda, Shizu

    2014-01-01

    The use of murine 3T3 feeder cells needs to be avoided when fabricating corneal epithelial cell sheets for use in treating ocular surface diseases. However, the expression level of the epithelial stem/progenitor cell marker, p63, is down-regulated in feeder-free culture systems. In this study, in order to fabricate corneal epithelial cell sheets that maintain colony-forming cells without using any feeder cells, we investigated the use of an oxygen-controlled method that was developed previously to fabricate cell sheets efficiently. Rabbit limbal epithelial cells were cultured under hypoxia (1-10% O2) and under normoxia during stratification after reaching confluence. Multilayered corneal epithelial cell sheets were fabricated using an oxygen-controlled method, and immunofluorescence analysis showed that cytokeratin 3 and p63 was expressed in appropriate localization in the cell sheets. The colony-forming efficiency of the cell sheets fabricated by the oxygen-controlled method without feeder cells was significantly higher than that of cell sheets fabricated under 20% O2 without feeder cells. These results indicate that the oxygen-controlled method has the potential to achieve a feeder-free culture system for fabricating corneal epithelial cell sheets for corneal regeneration. Copyright © 2013 Elsevier Ltd. All rights reserved.

  1. Replacement of murine fibroblasts by human fibroblasts irradiated in obtaining feeder layer for the culture of human keratinocytes

    Energy Technology Data Exchange (ETDEWEB)

    Yoshito, Daniele; Sufi, Bianca S.; Santin, Stefany P.; Mathor, Monica B. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Altran, Silvana C.; Isaac, Cesar [Universidade Sao Paulo (USP), Sao Paulo, SP (Brazil). Fac. de Medicina. Lab. de Microcirurgia Plastica; Esteves-Pedro, Natalia M. [Universidade Sao Paulo (USP), Sao Paulo, SP (Brazil). Fac. de Ciencias Farmaceuticas. Lab. de Controle Biologico; Herson, Marisa R. [DonorTissue Bank of Victoria (Australia)

    2011-07-01

    Human autologous epithelia cultivated in vitro, have been used successfully in treating damage to skin integrity. The methodology allowed the cultivation of these epithelia was described by Rheinwald and Green in 1975, this methodology consisted in seeding keratinocytes onto a feeder layer composed of lineage 3T3 murine fibroblasts, the proliferation rate is controlled through the action of ionizing radiation. However, currently there is a growing concern about the possibility of transmitting prions and murine viruses to transplanted patients. Taking into account this concern, in this present work, we replaced the feeder layer originally composed of murine fibroblasts by human fibroblasts. To obtain this new feeder layer was necessary to standardize the enough irradiation dose to inhibit the replication of human fibroblasts and the verification of effectiveness of the development of keratinocytes culture on a feeder layer thus obtained. According to the obtained results we can verify that the human fibroblasts irradiated at various tested doses (60, 70, 100, 200, 250 and 300 Gy) had their mitotic activity inactivated by irradiation, allowing the use of any of these doses to confection of the feeder layer, since these fibroblasts irradiated still showed viable until fourteen days of cultivation. In the test of colony formation efficiency was observed that keratinocytes seeded on irradiated human fibroblasts were able to develop satisfactorily, preserving their clonogenic potential. Therefore it was possible the replacement of murine fibroblasts by human fibroblasts in confection of the feeder layer, in order to eliminate this xenobiotic component of the keratinocytes culture. (author)

  2. Randomized trial of switching from prescribed non-selective non-steroidal anti-inflammatory drugs to prescribed celecoxib

    DEFF Research Database (Denmark)

    Macdonald, Thomas M; Hawkey, Chris J; Ford, Ian

    2017-01-01

    BACKGROUND: Selective cyclooxygenase-2 inhibitors and conventional non-selective non-steroidal anti-inflammatory drugs (nsNSAIDs) have been associated with adverse cardiovascular (CV) effects. We compared the CV safety of switching to celecoxib vs. continuing nsNSAID therapy in a European setting...

  3. A feeder-free culture using autogeneic conditioned medium for undifferentiated growth of human embryonic stem cells: Comparative expression profiles of mRNAs, microRNAs and proteins among different feeders and conditioned media

    Directory of Open Access Journals (Sweden)

    Chou Chi-Hsien

    2010-10-01

    Full Text Available Abstract Background Human embryonic stem (hES cell lines were derived from the inner cell mass of human blastocysts, and were cultured on mouse embryonic fibroblast (MEF feeder to maintain undifferentiated growth, extensive renewal capacity, and pluripotency. The hES-T3 cell line with normal female karyotype was previously used to differentiate into autogeneic fibroblast-like cells (T3HDF as feeder to support the undifferentiated growth of hES-T3 cells (T3/HDF for 14 passages. Results A feeder-free culture on Matrigel in hES medium conditioned by the autogeneic feeder cells (T3HDF was established to maintain the undifferentiated growth of hES-T3 cells (T3/CMHDF for 8 passages in this investigation. The gene expression profiles of mRNAs, microRNAs and proteins between the undifferentiated T3/HDF and T3/CMHDF cells were shown to be very similar, and their expression profiles were also found to be similar to those of T3/MEF and T3/CMMEF cells grown on MEF feeder and feeder-free Matrigel in MEF-conditioned medium, respectively. The undifferentiated state of T3/HDF and T3/CMHDF as well as T3/MEF andT3/CMMEF cells was evidenced by the very high expression levels of "stemness" genes and low expression levels of differentiation markers of ectoderm, mesoderm and endoderm in addition to the strong staining of OCT4 and NANOG. Conclusion The T3HDF feeder and T3HDF-conditioned medium were able to support the undifferentiated growth of hES cells, and they would be useful for drug development and toxicity testing in addition to the reduced risks of xenogeneic pathogens when used for medical applications such as cell therapies.

  4. Meta-analysis on the effects of the physical environment, animal traits, feeder and feed characteristics on the feeding behaviour and performance of growing-finishing pigs.

    Science.gov (United States)

    Averós, X; Brossard, L; Dourmad, J Y; de Greef, K H; Edwards, S A; Meunier-Salaün, M C

    2012-08-01

    A meta-analysis, using information from 45 experiments on growing-finishing pigs published in 39 manuscripts, was carried out to determine the simultaneous effects of the physical environment (space allowance, group size, flooring conditions, temperature, presence of enrichment), pig traits (initial body weight (BW) for each studied time interval, sex, genetics), feeder characteristics (water provision within the feeder, feeder design (individual/collective), feeder places/pig, presence of feeder protection) and feed characteristics (feed allowance (ad libitum/restricted), net energy content, crude protein (CP) content), as well as their potential interactions, on the feeding behaviour and performance of growing-finishing pigs. The detrimental effect of low temperature on performance was particularly evident for restricted-fed pigs (P < 0.05). At reduced feeder space allowance, a reduction in the percentage of time spent eating was predicted when increasing initial BW, whereas the opposite was predicted for larger feeder space allowances (P < 0.001). The reduction in visit duration to the feeder in higher BW groups became gradually more important with increasing feeder space allowance (P < 0.01), whereas the increase in the ingestion rate and average daily feed intake (ADFI) with increasing initial BW became smaller with increasing feeder space (P < 0.05). The model predicted a reduction in feed conversion ratio (FCR) with increasing group size (P < 0.05) and floor space allowance (P < 0.01) and on solid floors with or without bedding (P < 0.05). In comparison with other feeders, wet/dry feeders were associated with more frequent but shorter feeder visits (P < 0.05), higher ingestion rates (P < 0.001) and higher ADFI (P < 0.10). The use of protection within individual feeders increased the time spent feeding (P < 0.001), reduced the number of visits per day (P < 0.01), the ingestion rate (P < 0.001) and FCR (P < 0.01) in comparison with other feeder types. Sex

  5. Tumorigenic risk of human induced pluripotent stem cell explants cultured on mouse SNL76/7 feeder cells

    Energy Technology Data Exchange (ETDEWEB)

    Kamada, Mizuna; Mitsui, Youji, E-mail: y-mitsui8310@hb.tp1.jp; Kumazaki, Tsutomu; Kawahara, Yuta; Matsuo, Taira; Takahashi, Tomoko, E-mail: t-takahashi@kph.bunri-u.ac.jp

    2014-10-24

    Highlights: • hiPS cell explants formed malignant tumors when SNL76/7 feeder cells were used. • Multi type tumors developed by interaction of SNL76/7 feeder cells with hiPS cells. • Tumorigenic risk occurs by co-culture of hiPS cells with SNL76/7 feeder cells. - Abstract: The potential for tumor formation from transplanted human induced pluripotent stem cell (hiPSC) derivatives represents a high risk in their application to regenerative medicine. We examined the genetic origin and characteristics of tumors, that were formed when 13 hiPSC lines, established by ourselves, and 201B7 hiPSC from Kyoto University were transplanted into severe combined immune-deficient (SCID) mice. Though teratomas formed in 58% of mice, five angiosarcomas, one malignant solitary fibrous tumor and one undifferentiated pleomorphic sarcoma formed in the remaining mice. Three malignant cell lines were established from the tumors, which were derived from mitomycin C (MMC)-treated SNL76/7 (MMC-SNL) feeder cells, as tumor development from fusion cells between MMC-SNL and hiPSCs was negative by genetic analysis. While parent SNL76/7 cells produced malignant tumors, neither MMC-SNL nor MMC-treated mouse embryo fibroblast (MEF) produced malignant tumors. When MMC-SNL feeder cells were co-cultured with hiPSCs, growing cell lines were generated, that expressed genes similar to the parent SNL76/7 cells. Thus, hiPSCs grown on MMC-SNL feeder cells have a high risk of generating feeder-derived malignant tumors. The possible mechanism(s) of growth restoration and the formation of multiple tumor types are discussed with respect of the interactions between MMC-SNL and hiPSC.

  6. Differentiation of oligodendrocyte progenitor cells from dissociated monolayer and feeder-free cultured pluripotent stem cells.

    Science.gov (United States)

    Yamashita, Tomoko; Miyamoto, Yuki; Bando, Yoshio; Ono, Takashi; Kobayashi, Sakurako; Doi, Ayano; Araki, Toshihiro; Kato, Yosuke; Shirakawa, Takayuki; Suzuki, Yutaka; Yamauchi, Junji; Yoshida, Shigetaka; Sato, Naoya

    2017-01-01

    Oligodendrocytes myelinate axons and form myelin sheaths in the central nervous system. The development of therapies for demyelinating diseases, including multiple sclerosis and leukodystrophies, is a challenge because the pathogenic mechanisms of disease remain poorly understood. Primate pluripotent stem cell-derived oligodendrocytes are expected to help elucidate the molecular pathogenesis of these diseases. Oligodendrocytes have been successfully differentiated from human pluripotent stem cells. However, it is challenging to prepare large amounts of oligodendrocytes over a short amount of time because of manipulation difficulties under conventional primate pluripotent stem cell culture methods. We developed a proprietary dissociated monolayer and feeder-free culture system to handle pluripotent stem cell cultures. Because the dissociated monolayer and feeder-free culture system improves the quality and growth of primate pluripotent stem cells, these cells could potentially be differentiated into any desired functional cells and consistently cultured in large-scale conditions. In the current study, oligodendrocyte progenitor cells and mature oligodendrocytes were generated within three months from monkey embryonic stem cells. The embryonic stem cell-derived oligodendrocytes exhibited in vitro myelinogenic potency with rat dorsal root ganglion neurons. Additionally, the transplanted oligodendrocyte progenitor cells differentiated into myelin basic protein-positive mature oligodendrocytes in the mouse corpus callosum. This preparative method was used for human induced pluripotent stem cells, which were also successfully differentiated into oligodendrocyte progenitor cells and mature oligodendrocytes that were capable of myelinating rat dorsal root ganglion neurons. Moreover, it was possible to freeze, thaw, and successfully re-culture the differentiating cells. These results showed that embryonic stem cells and human induced pluripotent stem cells maintained in a

  7. Handling system for nuclear fuel cans to a fuel pellet feeder

    International Nuclear Information System (INIS)

    Vere, B.; Mathevon, P.

    1985-01-01

    The handling system comprises a first array of conveyors which takes a batch of casings from a delivery rack, alters the spacing between the casings, and delivers them to a vibrating table feeder, a second array of conveyors which readjusts the spacing between casing to its initial value and transfers the casings to a removal rack, and automatic and synchronized control means for ensuring the displacements of casings always in the same direction. The increase of spacing between casings can be used, before feeding, to allow them to be weighed one after the other, and after feeding, for cleaning the end part of fuel cans [fr

  8. Evaluation of the cryogenic mechanical properties of the insulation material for ITER Feeder superconducting joint

    Science.gov (United States)

    Wu, Zhixiong; Huang, Rongjin; Huang, ChuanJun; Yang, Yanfang; Huang, Xiongyi; Li, Laifeng

    2017-12-01

    The Glass-fiber reinforced plastic (GFRP) fabricated by the vacuum bag process was selected as the high voltage electrical insulation and mechanical support for the superconducting joints and the current leads for the ITER Feeder system. To evaluate the cryogenic mechanical properties of the GFRP, the mechanical properties such as the short beam strength (SBS), the tensile strength and the fatigue fracture strength after 30,000 cycles, were measured at 77K in this study. The results demonstrated that the GFRP met the design requirements of ITER.

  9. Research on communication system of underground safety management based on leaky feeder cable

    Institute of Scientific and Technical Information of China (English)

    CHEN Jian-hong; ZHANG Tao; CHENG Yun-cai; ZHANG Han

    2007-01-01

    According to the current working status of underground safety management and production scheduling, the importance and existed problem of underground mine radio communication were summarized, and the basic principle and classification of leaky feeder cable were introduced and the characteristics of cable were analyzed specifically in depth, and the application model of radio communication system for underground mine safety management was put forward. Meanwhile, the research explanation of the system component, function and evaluation was provided. The discussion result indicates that communication system of underground mine safety management which is integrated two-way relay amplifier and other equipment has many communication functions, and underground mine mobile communication can be achieved well.

  10. The Linehaul-Feeder Vehicle Routing Problem with Virtual Depots and Time Windows

    Directory of Open Access Journals (Sweden)

    Huey-Kuo Chen

    2011-01-01

    Full Text Available This paper addresses the linehaul-feeder vehicle routing problem with virtual depots and time windows (LFVRPTW. Small and large vehicles deliver services to customers within time constraints; small vehicles en route may reload commodities from either the physical depot or from the larger vehicle at a virtual depot before continuing onward. A two-stage solution heuristic involving Tabu search is proposed to solve this problem. The test results show that the LFVRPTW performs better than the vehicle routing problem with time windows in terms of both objective value and the number of small vehicles dispatched.

  11. A New Optimization Framework To Solve The Optimal Feeder Reconfiguration And Capacitor Placement Problems

    Directory of Open Access Journals (Sweden)

    Mohammad-Reza Askari

    2015-07-01

    Full Text Available Abstract This paper introduces a new stochastic optimization framework based bat algorithm BA to solve the optimal distribution feeder reconfiguration DFR as well as the shunt capacitor placement and sizing in the distribution systems. The objective functions to be investigated are minimization of the active power losses and minimization of the total network costs an. In order to consider the uncertainties of the active and reactive loads in the problem point estimate method PEM with 2m scheme is employed as the stochastic tool. The feasibility and good performance of the proposed method are examined on the IEEE 69-bus test system.

  12. Modeling and Control of Low Voltage Flexible Units for Enhanced Operation of Distribution Feeders

    DEFF Research Database (Denmark)

    Raboni, Pietro; Hu, Weihao; Chaudhary, Sanjay

    2013-01-01

    In some networks Distributed Generators (DGs) are phasing out conventional power plants in terms of power production but still large efforts are required for providing ancillary services. In this paper the usage of fast response units like a Micro Turbines (MT) and a stationary Electric Vehicle...... Battery (EVB) is proposed for providing primary regulation in grid connected mode and for hierarchically manage an islanded LV distribution feeder. The unit models are described and a novel EVB model directly based on manufacturer’s data is proposed and evaluated comparing its performances with Sim...

  13. "The good into the pot, the bad into the crop!"--a new technology to free stem cells from feeder cells.

    Directory of Open Access Journals (Sweden)

    Annette Schneider

    Full Text Available A variety of embryonic and adult stem cell lines require an initial co-culturing with feeder cells for non-differentiated growth, self renewal and maintenance of pluripotency. However for many downstream ES cell applications the feeder cells have to be considered contaminations that might interfere not just with the analysis of experimental data but also with clinical application and tissue engineering approaches. Here we introduce a novel technique that allows for the selection of pure feeder-freed stem cells, following stem cell proliferation on feeder cell layers. Complete and reproducible separation of feeder and embryonic stem cells was accomplished by adaptation of an automated cell selection system that resulted in the aspiration of distinct cell colonies or fraction of colonies according to predefined physical parameters. Analyzing neuronal differentiation we demonstrated feeder-freed stem cells to exhibit differentiation potentials comparable to embryonic stem cells differentiated under standard conditions. However, embryoid body growth as well as differentiation of stem cells into cardiomyocytes was significantly enhanced in feeder-freed cells, indicating a feeder cell dependent modulation of lineage differentiation during early embryoid body development. These findings underline the necessity to separate stem and feeder cells before the initiation of in vitro differentiation. The complete separation of stem and feeder cells by this new technology results in pure stem cell populations for translational approaches. Furthermore, a more detailed analysis of the effect of feeder cells on stem cell differentiation is now possible, that might facilitate the identification and development of new optimized human or genetically modified feeder cell lines.

  14. Vertical linear feeder to elliptical igneous saucer-shaped sills: evidences from structural observations, geochemistry and experimental modeling

    Science.gov (United States)

    Galerne, C. Y.; Galland, O.; Neumann, E. R.; Planke, S.

    2009-12-01

    The structural relationships between sills and their feeders are poorly documented because they are rarely observed in the field and difficult to image on seismic data. For instance, it is unclear whether sills are fed by pipes, dikes or other sills. Nevertheless, the geometrical relationships between sills and their feeders provide first-order constraints on magma emplacement mechanisms. Here, we investigate the structural and geochemical relationships between sills and potential feeder dikes in a remarkably well-preserved and exposed sill complex, the Golden Valley Sill Complex (GVSC), Karoo Basin, South Africa. The GVSC consists of five major saucer-shaped sills and six dikes. The Golden Valley sill itself is an elliptical saucer, with a N-S trend. A one meter thick dike (D4) crops out underneath the southern tip of the Golden Valley sill. The strike of this dike is parallel to the long axis of the Golden Valley sill. Detailed sampling and geochemical analyses of the GVSC show that each sill and dike exhibits a specific geochemical signature. The Golden Valley sill and its underlying dike D4 have identical signatures. Although there is no clear structural evidence, the consistent geometrical and geochemical relationships between the Golden Valley sill and the D4 dike suggest that this vertical linear structure is the feeder of the overlying saucer-shaped sill. In order to investigate the relationships between sills and feeders, we resorted to scaled laboratory experiments. The experiments consisted of a low-viscosity vegetable oil representing magma and a cohesive fine-grained silica flour representing brittle rocks. We placed a horizontal weak layer into the silica flour, just above the top of the inlet, to simulate strata. Such a weak layer controlled the formation of horizontal sill that subsequently turned into a transgressive sheet leading to the formation of a saucer geometry. We ran experiments with varying inlet shapes: 1) a point inlet representing a

  15. Differences in exam performance between pupils attending selective and non-selective schools mirror the genetic differences between them

    Science.gov (United States)

    Smith-Woolley, Emily; Pingault, Jean-Baptiste; Selzam, Saskia; Rimfeld, Kaili; Krapohl, Eva; von Stumm, Sophie; Asbury, Kathryn; Dale, Philip S.; Young, Toby; Allen, Rebecca; Kovas, Yulia; Plomin, Robert

    2018-03-01

    On average, students attending selective schools outperform their non-selective counterparts in national exams. These differences are often attributed to value added by the school, as well as factors schools use to select pupils, including ability, achievement and, in cases where schools charge tuition fees or are located in affluent areas, socioeconomic status. However, the possible role of DNA differences between students of different schools types has not yet been considered. We used a UK-representative sample of 4814 genotyped students to investigate exam performance at age 16 and genetic differences between students in three school types: state-funded, non-selective schools (`non-selective'), state-funded, selective schools (`grammar') and private schools, which are selective (`private'). We created a genome-wide polygenic score (GPS) derived from a genome-wide association study of years of education (EduYears). We found substantial mean genetic differences between students of different school types: students in non-selective schools had lower EduYears GPS compared to those in grammar (d = 0.41) and private schools (d = 0.37). Three times as many students in the top EduYears GPS decile went to a selective school compared to the bottom decile. These results were mirrored in the exam differences between school types. However, once we controlled for factors involved in pupil selection, there were no significant genetic differences between school types, and the variance in exam scores at age 16 explained by school type dropped from 7% to <1%. These results show that genetic and exam differences between school types are primarily due to the heritable characteristics involved in pupil admission.

  16. Assessing the role of benthic filter feeders on phytoplankton production in a shellfish farming site: Mont Saint Michel Bay, France

    Science.gov (United States)

    Cugier, Philippe; Struski, Caroline; Blanchard, Michel; Mazurié, Joseph; Pouvreau, Stéphane; Olivier, Frédéric; Trigui, Jihane R.; Thiébaut, Eric

    2010-07-01

    The macrobenthic community of Mont Saint Michel Bay (English Channel, France) is mainly dominated by filter feeders, including cultivated species (oysters and mussels). An ecological model of the bay was developed, coupling a 2D hydro-sedimentary model and two biological models for primary production and filter-feeder filtration. The filter-feeder model includes three cultivated species ( Mytilus edulis, Crassostrea gigas and Ostrea edulis), one invasive species ( Crepidula fornicata) and eight wild native species ( Abra alba, Cerastoderma edule, Glycymeris glycymeris, Lanice conchilega, Macoma balthica, Paphia rhomboides, Sabellaria alveolata, andSpisula ovalis). For cultivated and invasive species, the production of biodeposits was computed to assess their role in restimulating primary production. Chlorophyll a concentrations appeared to be strongly controlled by the filter feeders. When the pressure of each benthic compartment on phytoplankton was estimated separately wild species and the invasive slipper limpet C.fornicata were shown to be key elements in the control of primary production. Conversely, the role of cultivated species, particularly oysters, was weaker. Feedback due to the mineralization of biodeposits also appears to be crucial to fully evaluate the role of filter feeders in primary production.

  17. Effect of portion size and milk flow on the use of a milk feeder and the development of cross-sucking in dairy calves

    DEFF Research Database (Denmark)

    Nielsen, Per Peetz; Jensen, Margit Bak; Halekoh, Ulrich

    2018-01-01

    milk feeder in each pen, and exposed to four milk-feeding treatments in a cross-over design with four periods of 1 week. All four treatments involved a daily allowance of 8. L of whole milk, with variation in the maximum portion size and the rate at which milk entered the teat of the milk feeder......This study aimed to investigate whether reducing the milk flow and increasing the milk portion size of a computer-controlled milk feeder would lead to less cross-sucking and fewer unrewarded feeder visits in dairy calves. Five groups, each with 9 or 10 calves (n = 48), were housed in pens with one...

  18. Improvement of the auto wire feeder machine in a de-soldering process

    Directory of Open Access Journals (Sweden)

    Niramon Nonkhukhetkhong

    2016-10-01

    Full Text Available This paper presents the methodology of the de-soldering process for rework of disk drive Head Stack Assembly (HSA units. The auto wire feeder is a machine that generates Tin (Sn on the product. This machine was determined to be one of the major sources of excess Sn on the HSA. The defect rate due to excess Sn is more than 30%, which leads to increased processing time and cost to perform additional cleaning steps. From process analysis, the major causes of excess Sn are as follows: 1 The machine cannot cut the wire all the way into the flux core area; 2 The sizes and types of soldering irons are not appropriate for the unit parts; and, 3 There are variations introduced into the de-soldering process by the workforce. This paper proposes a methodology to address all three of these causes. First, the auto wire feeder machine in the de-solder process will be adjusted in order to cut wires into flux core. Second, the types of equipment and material used in de-soldering will be optimized. Finally, a new standard method for operators, which can be controlled more easily, will be developed in order to reduce defects due to workforce related variation. After these process controls and machine adjustments were implemented, the overall Sn related problems were significantly improved. Sn contamination was reduced by 41% and cycle time was reduced by an average of 15 seconds.

  19. Manufacture and testing of the CTB&SBB thermal shield for the ITER magnet feeder system

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Kun; Liu, Chen; Song, Yuntao; Feng, Hansheng; Ding, Kaizhong, E-mail: kzding@ipp.ac.cn; Wang, Tanbin; Ji, Hui

    2015-10-15

    The system of International Thermonuclear Experimental Reactor (ITER) feeders is responsible for the power, helium cooling, and instrumentation of the magnets of the coil terminal box and S-bend box (CTB&SBB) thermal shield outside the cryostat. An 80-K rectangular Al thermal shield is hung inside the CTB&SBB to reduce the thermal radiation heat loads of 4.5-K helium. The American Society of Interventional Pain Physicians (ASIPP) will supply all the 31 sets of feeders for ITER. A manufactured prototype of CTB&SBB thermal shield is first quality-tested before the commencement of the series production. First, a detailed configuration of the rectangular Al thermal shield is presented in this article. The paper also presents more information on the manufacturing process of the thermal shield, especially the welding process, the procedure for ensuring good weld quality, and the use of a specially designed tool to ensure <5-mm deformation on such a 7.3-m-long thermal shield during welding. In addition, the cold test and results, including the cooling process with 13-bar and 17.5-g/s 80-K He gas, and the temperature distribution on different panels of the thermal shield are presented. The whole process of manufacture and testing lays a good foundation for the series production of the thermal shield.

  20. Photovoltaic Hosting Capacity of Feeders with Reactive Power Control and Tap Changers

    Energy Technology Data Exchange (ETDEWEB)

    Ceylan, Oğuzhan; Paudyal, Sumit; Bhattarai, Bishnu P.; Myers, Kurt S.

    2017-06-01

    This paper proposes an algorithm to determine photovoltaic (PV) hosting capacity of power distribution networks as a function of number of PV injection nodes, reactive power support from the PVs, and the sub-station load tap changers (LTCs). In the proposed method, several minute by minute simulations are run based on randomly chosen PV injection nodes, daily PV output profiles, and daily load profiles from a pool of high-resolution realistic data set. The simulation setup is built using OpenDSS and MATLAB. The performance of the proposed method is investigated in the IEEE 123-node distribution feeder for multiple scenarios. The case studies are performed particularly for one, two, five and ten PV injection nodes, and looking at the maximum voltage deviations. Case studies show that the PV hosting capacity of the 123-node feeder greatly differs with the number of PV injection nodes. We have also observed that the PV hosting capacity increases with reactive power support and higher tap position of sub-station LTC.

  1. Stability-index based method for optimal Var planning in distribution feeders

    International Nuclear Information System (INIS)

    Hamouda, Abdellatif; Zehar, Khaled

    2011-01-01

    Research highlights: → Optimal Var planning is modelled using heuristic methods. → Capacitor sizes and location are determined by a two stage method. → Capacitor locations are determined using nodes stability-indices. → Their sizes are calculated subject to a new constraint on the branches reactive currents. → The solution is fast and leads to better results without over compensation. -- Abstract: The problem of the reactive energy optimal planning can be solved in a fast and efficient way using heuristic techniques. The latter reduce the number of the control variables to be determined and lead to a near global optimal solution. The capacitor appropriate locations are firstly determined by decisive indices then, their optimal sizes are calculated. In this paper a stability-index based method is presented. The nodes stability-indices are calculated for identifying the most sensitive nodes to be candidate for receiving near optimal standard capacitors that, reduce the feeder power losses, improve the voltage profile and maximise the economic saving (objective function). In this multi-objective optimisation problem, the commonly used voltage constraint is substituted by a new constraint on the branch reactive currents. This new constraint, allows overcoming the over compensation phenomenon by setting positive branch reactive currents. The solution is further improved by regulating the source node voltage. The proposed approach has been tested on several feeder examples and its effectiveness has been demonstrated through comparative studies. The obtained results have shown that the proposed approach leads to a promising and feasible solution.

  2. Stability-index based method for optimal Var planning in distribution feeders

    Energy Technology Data Exchange (ETDEWEB)

    Hamouda, Abdellatif, E-mail: a_hamouda1@yahoo.f [QUERE Laboratory, Optics and Mechanics Institut, University Ferhat Abbas, Setif 19000 (Algeria); Zehar, Khaled [QUERE Laboratory, Department of Electrical and Electronics Engineering, University of Bahrain, Isa Town (Bahrain)

    2011-05-15

    Research highlights: {yields} Optimal Var planning is modelled using heuristic methods. {yields} Capacitor sizes and location are determined by a two stage method. {yields} Capacitor locations are determined using nodes stability-indices. {yields} Their sizes are calculated subject to a new constraint on the branches reactive currents. {yields} The solution is fast and leads to better results without over compensation. -- Abstract: The problem of the reactive energy optimal planning can be solved in a fast and efficient way using heuristic techniques. The latter reduce the number of the control variables to be determined and lead to a near global optimal solution. The capacitor appropriate locations are firstly determined by decisive indices then, their optimal sizes are calculated. In this paper a stability-index based method is presented. The nodes stability-indices are calculated for identifying the most sensitive nodes to be candidate for receiving near optimal standard capacitors that, reduce the feeder power losses, improve the voltage profile and maximise the economic saving (objective function). In this multi-objective optimisation problem, the commonly used voltage constraint is substituted by a new constraint on the branch reactive currents. This new constraint, allows overcoming the over compensation phenomenon by setting positive branch reactive currents. The solution is further improved by regulating the source node voltage. The proposed approach has been tested on several feeder examples and its effectiveness has been demonstrated through comparative studies. The obtained results have shown that the proposed approach leads to a promising and feasible solution.

  3. Effect of Antimicrobial Dosage Regimen on Salmonella and Escherichia coli Isolates from Feeder Swine▿

    Science.gov (United States)

    Wagner, Bruce A.; Straw, Barbara E.; Fedorka-Cray, Paula J.; Dargatz, David A.

    2008-01-01

    A body of evidence exists that suggests that antimicrobial use in food animals leads to resistance in both pathogenic and commensal bacteria. This study focused on the impact of three different antimicrobial regimes (low-level continuous, pulse, and no antimicrobial) for two antimicrobials (chlortetracycline and tylosin) on the presence of Salmonella spp. and on the prevalence of antimicrobial resistance of both Salmonella spp. and nonspecific Escherichia coli in fecal samples from feeder swine. The prevalence of fecal samples positive for Salmonella spp. significantly decreased between the samples taken at feeder placement compared to samples taken when the animals were close to market weight. Differences in resistance of Salmonella spp. did not appear to be influenced by dosing treatment including the control. Analysis of antimicrobial resistance examining both susceptibility and resistance, as well as MIC outcomes, demonstrated that only resistance to cephalothin increased in E. coli under the pulse chlortetracycline treatment. These results suggest that the dosing regimes examined in this study did not lead to an increase in either the prevalence of Salmonella spp. or the prevalence of antimicrobial resistance in isolates of Salmonella spp. or E. coli. PMID:18223115

  4. Surgical management of dural arteriovenous fistulas with transosseous arterial feeders involving the jugular bulb.

    Science.gov (United States)

    Tirakotai, W; Benes, L; Kappus, C; Sure, U; Farhoud, A; Bien, S; Bertalanffy, H

    2007-01-01

    Dural arteriovenous fistulas located in the vicinity of the jugular foramen are complex vascular malformations and belong to the most challenging skull base lesions to treat. The authors comprehensively analyze multiple features in a series of dural arteriovenous fistulas with transosseous arterial feeders involving the jugular bulb. Four patients who underwent surgery via the transcondylar approach to treat dural arteriovenous fistulas around the jugular foramen were retrospectively reviewed. Previously, endovascular treatment was attempted in all patients. The success of the surgical treatment was examined with postoperative angiography. Complete obliteration of the dural arteriovenous fistulas (DAVFs) was achieved in three patients, and significant flow reduction in one individual. All patients had a good postoperative outcome, and only one experienced mild hypoglossal nerve palsy. Despite extensive bone drilling, an occipitocervical fusion was necessary in only one patient with bilateral lesions. The use of an individually tailored transcondylar approach to treat dural arteriovenous fistulas at the region of the jugular foramen is most effective. This approach allows for complete obliteration of the connecting arterial feeders, and removal of bony structures containing pathological vessels.

  5. Power Hardware-in-the-Loop Evaluation of PV Inverter Grid Support on Hawaiian Electric Feeders

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Austin A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Prabakar, Kumaraguru [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Nagarajan, Adarsh [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Nepal, Shaili [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hoke, Anderson F [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Asano, Marc [Hawaiian Electric Company; Ueda, Reid [Hawaiian Electric Company; Ifuku, Earle [Hawaiian Electric Company

    2017-10-03

    As more grid-connected photovoltaic (PV) inverters become compliant with evolving interconnections requirements, there is increased interest from utilities in understanding how to best deploy advanced grid-support functions (GSF) in the field. One efficient and cost-effective method to examine such deployment options is to leverage power hardware-in-the-loop (PHIL) testing methods, which combine the fidelity of hardware tests with the flexibility of computer simulation. This paper summarizes a study wherein two Hawaiian Electric feeder models were converted to real-time models using an OPAL-RT real-time digital testing platform, and integrated with models of GSF capable PV inverters based on characterization test data. The integrated model was subsequently used in PHIL testing to evaluate the effects of different fixed power factor and volt-watt control settings on voltage regulation of the selected feeders using physical inverters. Selected results are presented in this paper, and complete results of this study were provided as inputs for field deployment and technical interconnection requirements for grid-connected PV inverters on the Hawaiian Islands.

  6. Supervisory control and data acquisition system development for superconducting current feeder system of SST-1

    International Nuclear Information System (INIS)

    Patel, R.; Mahesuria, G.; Gupta, N.C.; Sonara, D.; Panchal, R.; Panchal, P.; Tanna, V.L.; Pradhan, S.

    2014-01-01

    The Current Feeders System (CFS) is essentially an optimized bridge between the power supply at room temperature and Super Conducting Magnet System (SCMS) of the SST-1 machine at 4.5 K.CFS is a complex electrical and cryogenic network which consists of ten pairs of 10 KA rating helium Vapor cooled Conventional Current Leads (VCCLs), superconducting (SC) current feeder and associated components. For the safe and reliable operation of CFS, it is equipped with different physical process parameters measuring instruments like flow, pressure, temperature, level, vacuum, voltage taps and final control element like control valves, heaters, vacuum pumps etc. PLC program is developed in ladder language for acquiring and controlling the process parameters. Independent SCADA applications developed in WonderwareIntouch software for data communication from PLC, front-end Graphical User Interface (GUI), auto-manual interface, real time trends, history trends, events and alarm pages. Time synchronized communication established between CFS control system and Industrial SQL server (InSQL) Historian for centralized storage of CFS process parameters which intern provides the CFS process data to SST-1 central control room. SCADA based data acquisition and data retrieval system is found to be satisfactory during the recent SST-1 cool down experiment. This paper describes the SCADA and PLC application development and their communication to InSQL server. (author)

  7. Enhanced Particle Swarm Optimization-Based Feeder Reconfiguration Considering Uncertain Large Photovoltaic Powers and Demands

    Directory of Open Access Journals (Sweden)

    Ying-Yi Hong

    2014-01-01

    Full Text Available The Kyoto protocol recommended that industrialized countries limit their green gas emissions in 2012 to 5.2% below 1990 levels. Photovoltaic (PV arrays provide clear and sustainable renewable energy to electric power systems. Solar PV arrays can be installed in distribution systems of rural and urban areas, as opposed to wind-turbine generators, which cause noise in surrounding environments. However, a large PV array (several MW may incur several operation problems, for example, low power quality and reverse power. This work presents a novel method to reconfigure the distribution feeders in order to prevent the injection of reverse power into a substation connected to the transmission level. Moreover, a two-stage algorithm is developed, in which the uncertain bus loads and PV powers are clustered by fuzzy-c-means to gain representative scenarios; optimal reconfiguration is then achieved by a novel mean-variance-based particle swarm optimization. The system loss is minimized while the operational constraints, including reverse power and voltage variation, are satisfied due to the optimal feeder reconfiguration. Simulation results obtained from a 70-bus distribution system with 4 large PV arrays validate the proposed method.

  8. A single-cell and feeder-free culture system for monkey embryonic stem cells.

    Science.gov (United States)

    Ono, Takashi; Suzuki, Yutaka; Kato, Yosuke; Fujita, Risako; Araki, Toshihiro; Yamashita, Tomoko; Kato, Hidemasa; Torii, Ryuzo; Sato, Naoya

    2014-01-01

    Primate pluripotent stem cells (PSCs), including embryonic stem cells (ESCs) and induced pluripotent stem cells (iPSCs), hold great potential for research and application in regenerative medicine and drug discovery. To maximize primate PSC potential, a practical system is required for generating desired functional cells and reproducible differentiation techniques. Much progress regarding their culture systems has been reported to date; however, better methods would still be required for their practical use, particularly in industrial and clinical fields. Here we report a new single-cell and feeder-free culture system for primate PSCs, the key feature of which is an originally formulated serum-free medium containing FGF and activin. In this culture system, cynomolgus monkey ESCs can be passaged many times by single-cell dissociation with traditional trypsin treatment and can be propagated with a high proliferation rate as a monolayer without any feeder cells; further, typical PSC properties and genomic stability can be retained. In addition, it has been demonstrated that monkey ESCs maintained in the culture system can be used for various experiments such as in vitro differentiation and gene manipulation. Thus, compared with the conventional culture system, monkey ESCs grown in the aforementioned culture system can serve as a cell source with the following practical advantages: simple, stable, and easy cell maintenance; gene manipulation; cryopreservation; and desired differentiation. We propose that this culture system can serve as a reliable platform to prepare primate PSCs useful for future research and application.

  9. Eddy current array probe for detection of surface breaking cracks in the extrados of feeder bends

    International Nuclear Information System (INIS)

    Obrutsky, L.S.; Cassidy, R.A.; Chaplin, K.; Martin, P.; Bureau, J.F.

    2006-01-01

    A new eddy current array probe has been implemented as a straightforward and promising technique for detection of outer diameter (OD) surface-breaking cracks on the extrados of feeder bends. The design is based on previous work performed at AECL, which had demonstrated that eddy current probes with laterally displaced transmit-receive coils can overcome some of the limitations of inspecting ferritic steel components for surface-breaking cracks. The Feeder Integrity Joint Program-CANDU Owners Group Inc. (FIJP-COG) Non-Destructive Evaluation (NDE) Team members commissioned AECL to work in collaboration with the probe manufacturer ZETEC, to develop a field usable eddy current array probe. The objective was to acquire a technique with the following capabilities: fast scanning non-contact inspection technique for surface breaking discontinuities; full inspection of the bend extrados OD surface in a single scan; ability to inspect first and second bends with similar settings and capabilities; permanent record for future reference; axial and circumferential crack detection in a single scan; capability to detect OD surface-breaking cracks, which can provide additional information to that provided by ultrasonic testing (UT) for flaw characterization, and detection threshold: Surface breaking cracks equivalent to a 0.5 mm deep, 10 mm long EDM notch located on the OD of the bend extrados. This paper discusses the basis for probe design, summarizes the experimental work to evaluate probe capabilities and analyzes the results from the field trial. (author)

  10. Eddy current array probe for detection of surface breaking cracks in the extrados of feeder bends

    Energy Technology Data Exchange (ETDEWEB)

    Obrutsky, L.S.; Cassidy, R.A.; Chaplin, K. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada)]. E-mail: obrutskyl@aecl.ca; Martin, P. [NB Power, Point Lepreau NGS, Point Lepreau, New Brunswick (Canada)]. E-mail: PMartin@nbpower.com; Bureau, J.F. [Zetec, Quebec, Quebec (Canada)]. E-mail: jean-francois.bureau@zetec.com

    2006-07-01

    A new eddy current array probe has been implemented as a straightforward and promising technique for detection of outer diameter (OD) surface-breaking cracks on the extrados of feeder bends. The design is based on previous work performed at AECL, which had demonstrated that eddy current probes with laterally displaced transmit-receive coils can overcome some of the limitations of inspecting ferritic steel components for surface-breaking cracks. The Feeder Integrity Joint Program-CANDU Owners Group Inc. (FIJP-COG) Non-Destructive Evaluation (NDE) Team members commissioned AECL to work in collaboration with the probe manufacturer ZETEC, to develop a field usable eddy current array probe. The objective was to acquire a technique with the following capabilities: fast scanning non-contact inspection technique for surface breaking discontinuities; full inspection of the bend extrados OD surface in a single scan; ability to inspect first and second bends with similar settings and capabilities; permanent record for future reference; axial and circumferential crack detection in a single scan; capability to detect OD surface-breaking cracks, which can provide additional information to that provided by ultrasonic testing (UT) for flaw characterization, and detection threshold: Surface breaking cracks equivalent to a 0.5 mm deep, 10 mm long EDM notch located on the OD of the bend extrados. This paper discusses the basis for probe design, summarizes the experimental work to evaluate probe capabilities and analyzes the results from the field trial. (author)

  11. Design of Two Feeder Three Phase Four Wire Distribution System Utilizing Multi Converter UPQC with Fuzzy Logic Controller

    Directory of Open Access Journals (Sweden)

    Chandra Babu Paduchuri

    2014-01-01

    Full Text Available This paper proposes the instantaneous p-q theory based fuzzy logic controller (FLC for multi converter unified power quality conditioner (MC-UPQC to mitigate power quality issues in two feeders three-phase four-wire distribution systems. The proposed system is extended system of the existing one feeder three-phase four-wire distribution system, which is operated with UPQC. This system is employed with three voltage source converters, which are connected commonly to two feeder distribution systems. The performance of this proposed system used to compensate voltage sag, neutral current mitigation and compensation of voltage and current harmonics under linear and nonlinear load conditions. The neutral current flowing in series transformers is zero in the implementation of the proposed system. The simulation performance analysis is carried out using MATLAB.

  12. Non-selective vs. selective beta-blocker treatment and the risk of thrombo-embolic events in patients with heart failure

    NARCIS (Netherlands)

    de Peuter, Olav R.; Souverein, Patrick C.; Klungel, Olaf H.; Büller, Harry R.; de Boer, Anthonius; Kamphuisen, Pieter W.

    2011-01-01

    Aims Heart failure (HF) is associated with a prothrombotic state, resulting in an increased risk for thrombo-embolic events. Studies suggest a reduced prothrombotic state when non-selective beta-blockers relative to selective beta-blockers are given. We studied the influence of non-selective

  13. Applicability of ANSYS ELBOW290 element for flexibility calculation of tight radius bends on feeder pipes in CANDU reactors

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, X., E-mail: Xuan.Zhang@candu.com [Candu Energy Inc, Mississauga, ON (Canada)

    2015-07-01

    A curved pipe element, ELBOW290, became available in ANSYS 12. This element was developed based on a simplified shell theory, and maintains the ability to capture cross-sectional deformations of elbows. Numerical testing on the applicability of this element for the flexibility calculation of the tight radius bends in CANDU reactors is carried out to determine the usability of this element in completing stress analyses for feeder pipes. Comparisons are made between the ELBOW290 and the shell element for various feeder bend types found in domestic and overseas CANDU reactors. The comparisons show that the ELBOW290 element is suitable for calculating the flexibility of the tight radius bends. (author)

  14. The use of multiple imputation for the accurate measurements of individual feed intake by electronic feeders.

    Science.gov (United States)

    Jiao, S; Tiezzi, F; Huang, Y; Gray, K A; Maltecca, C

    2016-02-01

    Obtaining accurate individual feed intake records is the key first step in achieving genetic progress toward more efficient nutrient utilization in pigs. Feed intake records collected by electronic feeding systems contain errors (erroneous and abnormal values exceeding certain cutoff criteria), which are due to feeder malfunction or animal-feeder interaction. In this study, we examined the use of a novel data-editing strategy involving multiple imputation to minimize the impact of errors and missing values on the quality of feed intake data collected by an electronic feeding system. Accuracy of feed intake data adjustment obtained from the conventional linear mixed model (LMM) approach was compared with 2 alternative implementations of multiple imputation by chained equation, denoted as MI (multiple imputation) and MICE (multiple imputation by chained equation). The 3 methods were compared under 3 scenarios, where 5, 10, and 20% feed intake error rates were simulated. Each of the scenarios was replicated 5 times. Accuracy of the alternative error adjustment was measured as the correlation between the true daily feed intake (DFI; daily feed intake in the testing period) or true ADFI (the mean DFI across testing period) and the adjusted DFI or adjusted ADFI. In the editing process, error cutoff criteria are used to define if a feed intake visit contains errors. To investigate the possibility that the error cutoff criteria may affect any of the 3 methods, the simulation was repeated with 2 alternative error cutoff values. Multiple imputation methods outperformed the LMM approach in all scenarios with mean accuracies of 96.7, 93.5, and 90.2% obtained with MI and 96.8, 94.4, and 90.1% obtained with MICE compared with 91.0, 82.6, and 68.7% using LMM for DFI. Similar results were obtained for ADFI. Furthermore, multiple imputation methods consistently performed better than LMM regardless of the cutoff criteria applied to define errors. In conclusion, multiple imputation

  15. Tsunami deposits

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-08-15

    The NSC (the Nuclear Safety Commission of Japan) demand to survey on tsunami deposits by use of various technical methods (Dec. 2011), because tsunami deposits have useful information on tsunami activity, tsunami source etc. However, there are no guidelines on tsunami deposit survey in JAPAN. In order to prepare the guideline of tsunami deposits survey and evaluation and to develop the method of tsunami source estimation on the basis of tsunami deposits, JNES carried out the following issues; (1) organizing information of paleoseismological record and tsunami deposit by literature research, (2) field survey on tsunami deposit, and (3) designing the analysis code of sediment transport due to tsunami. As to (1), we organize the information gained about tsunami deposits in the database. As to (2), we consolidate methods for surveying and identifying tsunami deposits in the lake based on results of the field survey in Fukui Pref., carried out by JNES. In addition, as to (3), we design the experimental instrument for hydraulic experiment on sediment transport and sedimentation due to tsunamis. These results are reflected in the guideline on the tsunami deposits survey and evaluation. (author)

  16. Tsunami deposits

    International Nuclear Information System (INIS)

    2013-01-01

    The NSC (the Nuclear Safety Commission of Japan) demand to survey on tsunami deposits by use of various technical methods (Dec. 2011), because tsunami deposits have useful information on tsunami activity, tsunami source etc. However, there are no guidelines on tsunami deposit survey in JAPAN. In order to prepare the guideline of tsunami deposits survey and evaluation and to develop the method of tsunami source estimation on the basis of tsunami deposits, JNES carried out the following issues; (1) organizing information of paleoseismological record and tsunami deposit by literature research, (2) field survey on tsunami deposit, and (3) designing the analysis code of sediment transport due to tsunami. As to (1), we organize the information gained about tsunami deposits in the database. As to (2), we consolidate methods for surveying and identifying tsunami deposits in the lake based on results of the field survey in Fukui Pref., carried out by JNES. In addition, as to (3), we design the experimental instrument for hydraulic experiment on sediment transport and sedimentation due to tsunamis. These results are reflected in the guideline on the tsunami deposits survey and evaluation. (author)

  17. Feeders of Free-Roaming Cats: Personal Characteristics, Feeding Practices, and Data on Cat Health and Welfare in an Urban Setting of Israel.

    Science.gov (United States)

    Gunther, Idit; Raz, Tal; Even Zor, Yehonatan; Bachowski, Yuval; Klement, Eyal

    2016-01-01

    Cat feeders serve as an important source of available food for free-roaming cats (FRCs) and can play a central role in providing data on FRC distribution, welfare, and health. Data on cat feeder personalities as well as a better understanding of their feeding practices offer relevance for decision making concerning FRC population control strategies. The current study surveyed 222 FRC feeders who responded to a municipal trap-neuter-return (TNR) campaign in an Israeli central urban setting. The aim of the study was to describe their personal characteristics, feeding practices, and the FRC populations they feed. Feeders were divided into four groups according to the number of cats they claimed to feed per day (group 1: fed up to 5 cats, group 2: fed 6-10 cats, group 3: fed 11-20 cats, and group 4: fed ≥21 cats). Most feeders were women (81%), with a median age of 58 years (range 18-81). The feeders reported an overall feeding of 3337 cats in 342 different feeding locations. Feeders of group 4 comprised 15.31% (n = 34) of all feeders but fed 56% (n = 1869) of the FRC in 37.42% (n = 128) of the feeding locations. "Heavy" feeders (groups 3 and 4) reported that they traveled significantly longer distances in order to feed the cats. Commercial dry food consisted of 90% of the food they provided, with 66% of them feeding once a day, with less food per cat per day than the other feeder groups. Interestingly, "heavy" feeders were usually singles, had on average fewer siblings, a clear preference for owning cats as pets, and lived in lower income neighborhoods. According to the feeders' reports on the FRC populations they fed, 69.7% (2325/3337) cats were neutered and 11.8% (395/3337) were kittens. In addition, they reported that 1.6% (54/3337) of the cats were limping, 2% (67/3337) suffered from a systemic disease, 4% (135/3337) had skin lesions, and 3.9% (130/3337) were suffering from a chronic disability. Abundance of kittens and morbidity rate were

  18. A model for strategic selection of feeder management systems: A case study

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Hsing Hung [Faculty of Management and Administration, Macau University of Science and Technology, Avenue Wei Long, Taipa, Macau (China); Lee, Amy H.I. [Department of Industrial Management, Chung Hua University, No. 707, Sec. 2, Wu Fu Rd., Hsinchu 300 (China); Kang, He-Yau [Department of Industrial Engineering and Management, National Chin-Yi University of Technology, 35, Lane 215, Sec. 1, Chung San Rd., Taiping, Taichung 411 (China)

    2010-06-15

    The move to integrating distribution management system (DMS) and feeder management system (FMS) in China is becoming the main trend in recent years, in addition to upgrading and rebuilding existing energy management system (EMS) and DMS. However, with increasing complexity in the social environments along with rapidly changing technologies, how to select a suitable contractor and a FMS project is becoming an important issue for electric power companies. This paper first briefly introduces FMS and then lists its critical success criteria. A model that applies a multi-criteria decision-making (MCDM) method, an analytic network process (ANP) associated with benefits, opportunities, costs and risks (BOCR), is constructed to help power companies to select the most suitable FMS project. (author)

  19. Effect of feeders in 3D modeling of low impedance multilayer CPW transmission line

    Science.gov (United States)

    Zaini, R. I.; Kyabaggu, P. B. K.; Sinulingga, E. P.

    2018-02-01

    Improved characteristics with low dissipation loss MMICs are highly desirable for wireless communications. However, the current industrial MMIC design is mainly based on microstrip concept which suffered from parasitic and unwanted phenomenon especially at higher frequency (>20 GHz). On the other hand, for future wireless technology, higher frequency operation is required and on-wafer microwave characterizations as well as precise modeling of 3D Multilayer CPW components are vital. This project concerns with understanding of the microwave characteristics behavior of Multilayer CPW components in MMIC applications. Feeder effect as unwanted parts in the characteristics has been investigated to determine its relation with the half wavelength resonance of the Multilayer CPW Low Impedance Transmission Line.

  20. A Survey of Pesticide Accumulation in a Specialist Feeder, the Koala (Phascolarctos cinereus).

    Science.gov (United States)

    Marschner, Caroline; Higgins, Damien P; Krockenberger, Mark B

    2017-09-01

    To maintain profitability in Australia's agricultural and urban landscapes pesticides are used throughout the range of koala habitats. The koala is a specialist feeder, reliant on metabolic enzyme capacities to utilise a toxic diet of eucalypt leaves and is potentially prone to adverse effects when xenobiotic interactions between dietary and anthropogenic xenobiotics occur. The aim of this study was to investigate accumulation of frequently used pesticides in wild koalas in 4 areas of New South Wales and Queensland. Liver samples of 57 deceased koalas were collected from care facilities and analysed using a modified QuEChERS extraction method followed by GCMSMS, HRLCMS and LCMSMS. No accumulation of any of the 166 investigated pesticides was found. Data indicate hepatic accumulation of pesticides in this species is uncommon even with close interactions with intensive land use. Despite the lack of hepatic bioaccumulation, this study cannot exclude a direct effect on hepatocellular metabolic pathways.

  1. Complete nutrient content of four species of commercially available feeder insects fed enhanced diets during growth.

    Science.gov (United States)

    Finke, Mark D

    2015-11-01

    Commercially raised feeder insects used to feed captive insectivores are a good source of many nutrients but are deficient in several key nutrients. Current methods used to supplement insects include dusting and gut-loading. Here, we report on the nutrient composition of four species of commercially raised feeder insects fed a special diet to enhance their nutrient content. Crickets, mealworms, superworms, and waxworms were analyzed for moisture, crude protein, fat, ash, acid detergent fiber, total dietary fiber, minerals, amino acids, fatty acids, vitamins, taurine, carotenoids, inositol, and cholesterol. All four species contained enhanced levels of vitamin E and omega 3 fatty acids when compared to previously published data for these species. Crickets, superworms, and mealworms contained β-carotene although using standard conversion factors only crickets and superworms would likely contain sufficient vitamin A activity for most species of insectivores. Waxworms did not contain any detectable β-carotene but did contain zeaxanthin which they likely converted from dietary β-carotene. All four species contained significant amounts of both inositol and cholesterol. Like previous reports all insects were a poor source of calcium and only superworms contained vitamin D above the limit of detection. When compared to the nutrient requirements as established by the NRC for growing rats or poultry, these species were good sources of most other nutrients although the high fat and low moisture content of both waxworms and superworms means when corrected for energy density these two species were deficient in more nutrients than crickets or mealworms. These data show the value of modifying the diet of commercially available insects as they are growing to enhance their nutrient content. They also suggest that for most insectivores properly supplemented lower fat insects such as crickets, or smaller mealworms should form the bulk of the diet. © 2015 The Authors. Zoo Biology

  2. The impact of deprivation on youth violence: a comparison of cities and their feeder towns.

    Science.gov (United States)

    Jones, S J; Sivarajasingam, V; Shepherd, J

    2011-06-01

    66,000 children and adolescents are treated at emergency departments (EDs) in England and Wales each year for assault injury. The aim of this study was to compare adolescent assault injury rates in cities and towns and determine how assault injury varies with deprivation and gender. The study was set in three cities in Wales, UK, and their surrounding towns. Subjects were 11-17 year olds treated for assault injury at one of seven EDs from 1 October 2005 to 30 September 2006. Area of residence (electoral divisions, EDivs) was identified from patient postcode. EDivs were aggregated into deprivation fifths for males and females and cities and towns. Assault injury rates, rate ratios and 95% CIs were calculated. 1472 children and adolescents of 11-17 years old were treated for assault injury. Male city assault injury rates were 14.2/1000 11-17 year olds; and 13.1 in towns. Female city assault injury rates were 6.0; and 5.6 in towns. In the most deprived city areas males had assault injury rates 2.6 times (95% CI 1.85 to 3.59) that of the most affluent, compared with 2.0 times in towns (95% CI 1.39 to 2.86). For females, the most deprived city areas had assault injury rates 5.3 times that of the most affluent (95% CI 2.93 to 9.41), compared with 2.8 times in towns (95% CI 1.47 to 5.28). Injury in youth violence increased with increasing deprivation in cities and their feeder towns. This was true for boys and girls, though rates for boys were consistently higher. This link between assault injury and deprivation was stronger for girls in cities than in feeder towns. Strategies to prevent youth violence need to include improved safeguarding arrangements for girls living in the most deprived city areas.

  3. USULAN PERBAIKAN OPERATION POINT SHEET PADA MESIN FEEDER AIDA 1100 PT. XXX DENGAN MENGGUNAKAN METODE SMED

    Directory of Open Access Journals (Sweden)

    Ary Arvianto

    2012-02-01

    Full Text Available Single Minute Exchange of Die (SMED merupakan salah satu alat lean yang penting untuk mengurangi waste dan meningkatkan fleksibilitas dalam proses manufaktur yang memungkinkan dalam pengurangan ukuran lot dan perbaikan aliran manufaktur. SMED mengurangi waktu non-produktif dengan mempersatukan dan standardisasi operasi dalam pergantian alat, dengan menggunakan teknik sederhana dan aplikasi yang mudah. Namun proses tersebut tidak dapat memberikan hasil yang  spesifik dalam pelaksanaannya, dimana masih dapat dilakukan suatu perbaikan. Untuk mengatasi hal ini, data statistik dan alat-alat teknik industri dapat diintegrasikan dalam pendekatan SMED untuk meningkatkan hasil penerapan SMED. Penerapan pendekatan SMED yang diusulkan diuji untuk mesin feeder didalam industri otomotif PT. XXX. Implementasi ini memungkinkan adanya pengurangan waktu setup, melalui reorganisasi sumber daya internal perusahaan tanpa membutuhkan investasi yang signifikan.   Kata kunci: Lean manufacturing systems, Single Minute Exchange of Die, Quick ChangeOver.     Single Minute Exchange of Die (SMED is one of the essential lean tools to reduce waste and increase flexibility in manufacturing processes that enable the reduction of lot size and improving manufacturing flow. SMED reduces non-productive time by streamlining and standardizing operations in the turn of the tool, using simple techniques and easy application. But the process can not provide a specific result in the implementation, which can still be an improvement. To overcome this, statistical data and tools can be integrated in industrial engineering approaches to improve outcomes SMED SMED implementation. The proposed application of SMED approach was tested for the automotive industry in the feeder machine PT. XXX. This implementation allows for the reduction of setup time, through the reorganization of the company's internal resources without requiring significant investment. Keywords: Lean manufacturing

  4. Urban and rural habitats differ in number and type of bird feeders and in bird species consuming supplementary food.

    Science.gov (United States)

    Tryjanowski, Piotr; Skórka, Piotr; Sparks, Tim H; Biaduń, Waldemar; Brauze, Tomasz; Hetmański, Tomasz; Martyka, Rafał; Indykiewicz, Piotr; Myczko, Łukasz; Kunysz, Przemysław; Kawa, Piotr; Czyż, Stanisław; Czechowski, Paweł; Polakowski, Michał; Zduniak, Piotr; Jerzak, Leszek; Janiszewski, Tomasz; Goławski, Artur; Duduś, Leszek; Nowakowski, Jacek J; Wuczyński, Andrzej; Wysocki, Dariusz

    2015-10-01

    Bird feeding is one of the most widespread direct interactions between man and nature, and this has important social and environmental consequences. However, this activity can differ between rural and urban habitats, due to inter alia habitat structure, human behaviour and the composition of wintering bird communities. We counted birds in 156 squares (0.25 km(2) each) in December 2012 and again in January 2013 in locations in and around 26 towns and cities across Poland (in each urban area, we surveyed 3 squares and also 3 squares in nearby rural areas). At each count, we noted the number of bird feeders, the number of bird feeders with food, the type of feeders, additional food supplies potentially available for birds (bread offered by people, bins) and finally the birds themselves. In winter, urban and rural areas differ in the availability of food offered intentionally and unintentionally to birds by humans. Both types of food availability are higher in urban areas. Our findings suggest that different types of bird feeder support only those species specialized for that particular food type and this relationship is similar in urban and rural areas.

  5. Establishment of feeder-free culture system for human induced pluripotent stem cell on DAS nanocrystalline graphene

    Science.gov (United States)

    Lee, Hyunah; Nam, Donggyu; Choi, Jae-Kyung; Araúzo-Bravo, Marcos J.; Kwon, Soon-Yong; Zaehres, Holm; Lee, Taehee; Park, Chan Young; Kang, Hyun-Wook; Schöler, Hans R.; Kim, Jeong Beom

    2016-02-01

    The maintenance of undifferentiated human pluripotent stem cells (hPSC) under xeno-free condition requires the use of human feeder cells or extracellular matrix (ECM) coating. However, human-derived sources may cause human pathogen contamination by viral or non-viral agents to the patients. Here we demonstrate feeder-free and xeno-free culture system for hPSC expansion using diffusion assisted synthesis-grown nanocrystalline graphene (DAS-NG), a synthetic non-biological nanomaterial which completely rule out the concern of human pathogen contamination. DAS-NG exhibited advanced biocompatibilities including surface nanoroughness, oxygen containing functional groups and hydrophilicity. hPSC cultured on DAS-NG could maintain pluripotency in vitro and in vivo, and especially cell adhesion-related gene expression profile was comparable to those of cultured on feeders, while hPSC cultured without DAS-NG differentiated spontaneously with high expression of somatic cell-enriched adhesion genes. This feeder-free and xeno-free culture method using DAS-NG will facilitate the generation of clinical-grade hPSC.

  6. Feeder-cell-independent culture of the pig-embryonic-stem-cell-derived exocrine pancreatic cell line, PICM-31

    Science.gov (United States)

    The adaptation to feeder-independent growth of a pig embryonic stem cell-derived pancreatic cell line is described. The parental PICM-31 cell line, previously characterized as an exocrine pancreas cell line, was colony-cloned two times in succession resulting in the subclonal cell line, PICM-31A1. P...

  7. 47 CFR 25.147 - Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz. 25.147 Section 25.147 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Applications and Licenses Space...

  8. Flurbiprofen : A non-selective cyclooxygenase (COX) inhibitor for treatment of non-infectious, non-necrotising anterior scleritis

    Science.gov (United States)

    Agrawal, Rupesh; Lee, Cecilia; Gonzalez-Lopez, Julio J.; Khan, Sharmina; Rodrigues, Valeria; Pavesio, Carlos

    2016-01-01

    Objective To analyse the safety and efficacy of a non-selective cyclo-oxygenase (COX) inhibitor in the management of non-infectious, non-necrotising anterior scleritis. Methods Retrospective chart review of 126 patients with non-necrotising anterior scleritis treated with oral flurbiprofen (Froben®(Abbott Healthcare)) with ( group B, n=61) or without topical steroids (group A, n=65) was performed and time to remission was plotted. Results The observed incidence rate was 1.07 (95% CI: 0.57–1.99) per 1000 person-years with failure rate of 0.68 (95% CI: 0.22–2.12) per 1000 person-years in group A and 1.41 (95% CI: 0.67–2.96) per 1000 person-years in group B. The failure rate was 3.97(1.89–9.34) per 1000 person-years with hazard ratio of 10.01 ( 95% CI: 2.52–39.65; p<0.001) for patients with associated systemic disease. Conclusion To our best knowledge, this is the first and largest case series on the safety and efficacy of a non-selective COX inhibitor in the management of anterior scleritis. PMID:26308394

  9. [Non-selective and selective non-steroidal anti-inflammatory drugs, administration in pregnancy and breast feeding].

    Science.gov (United States)

    Fardet, Laurence; Nizard, Jacky; Généreau, Thierry

    2002-09-28

    THE FACTS: Non steroidal anti-inflammatory drugs (NSAI), except aspirin, are classically contraindicated during pregnancy. Nevertheless, they are widely used, in particular by the obstetricians. During pregnancy, the potential toxicity of these drugs is double, maternal and fetal. The maternal toxicity is comparable to that, already known in adults, with however, some particularities at the time of labor and delivery. The fetal toxicity is mainly renal and cardiovascular, with the NSAI responsible for oligoamniosis and premature closure of the arterial canal of the fetus. On the other hand, the use of these molecules during breast-feeding does not seem source of adverse events, notably in the newborn. THE VARIOUS MOLECULES: Among the family of non-selective non-steroidal anti-inflammatories, indications and adverse events of the various molecules differ considerably. Moreover, whereas the majority of these molecules are non-selective, i.e. inhibiting the two isoforms of cyclooxygenase, new therapeutics, specifically inhibiting cyclooxygenase-2, are now available. Few studies have been published concerning their prescription during pregnancy and breast-feeding and their maternal and fetal side effects remain ignored by most of the practitioners.

  10. Developmental Competence of Buffalo (Bubalus bubalis) Pluripotent Embryonic Stem Cells Over Different Homologous Feeder Layers and the Comparative Evaluation with Various Extracellular Matrices.

    Science.gov (United States)

    Sharma, Manjinder; Dubey, Pawan K; Kumar, Rajesh; Nath, Amar; Kumar, G Sai; Sharma, G Taru

    2013-05-01

    Use of somatic cells as a feeder layer to maintain the embryonic stem cells (ESCs) in undifferentiated state limits the stem cell research design, since experimental data may result from a combined ESCs and feeder cell response to various stimuli. Therefore, present study was designed to evaluate the developmental competence of the buffalo ESCs over different homogenous feeders and compare with various extracellular matrices using different concentrations of LIF. Inner cell masses (ICMs) of in vitro hatched blastocysts were cultured onto homologous feeders viz. fetal fibroblast, granulosa and oviductal cell feeder layers and synthetic matrices viz. fibronectin, collagen type I and matrigel in culture medium. Developmental efficiency was found higher for ESCs cultured on fetal fibroblast and granulosa layers (83.33%) followed by fibronectin (77.78%) at 30 ng LIF. Oviductal feeder was found to be the least efficient feeder showing only 11.11% undifferentiated primary ESC colonies at 30 ng LIF. However, neither feeder layer nor synthetic matrix could support the development of primary colonies at 10 ng LIF. Expression of SSEA- 4, TRA-1-60 and Oct-4 were found positive in ESC colonies from all the feeders and synthetic matrices with 20 ng and 30 ng LIF. Fetal fibroblast and granulosa cell while, amongst synthetic matrices, fibronectin were found to be equally efficient to support the growth and maintenance of ESCs pluripotency with 30 ng LIF. This well-defined culture conditions may provide an animal model for culturing human embryonic stem cells in the xeno-free or feeder-free conditions for future clinical applications.

  11. Cone-Beam Computed Tomography (CBCT) Hepatic Arteriography in Chemoembolization for Hepatocellular Carcinoma: Performance Depicting Tumors and Tumor Feeders

    Energy Technology Data Exchange (ETDEWEB)

    Lee, In Joon [National Cancer Center, Department of Radiology (Korea, Republic of); Chung, Jin Wook, E-mail: chungjw@snu.ac.kr; Yin, Yong Hu; Kim, Hyo-Cheol; Kim, Young Il; Jae, Hwan Jun; Park, Jae Hyung [Seoul National University College of Medicine, Seoul National University Hospital, Department of Radiology (Korea, Republic of)

    2015-10-15

    PurposeThis study was designed to analyze retrospectively the performance of cone-beam computed tomography (CBCT) hepatic arteriography in depicting tumors and their feeders and to investigate the related determining factors in chemoembolization for hepatocellular carcinoma (HCC).MethodsEighty-six patients with 142 tumors satisfying the imaging diagnosis criteria of HCC were included in this study. The performance of CBCT hepatic arteriography for chemoembolization per tumor and per patient was evaluated using maximum intensity projection images alone (MIP analysis) or MIP combined with multiplanar reformation images (MIP + MPR analysis) regarding the following three aspects: tumor depiction, confidence of tumor feeder detection, and trackability of tumor feeders. Tumor size, tumor enhancement, tumor location, number of feeders, diaphragmatic motion, portal vein enhancement, and hepatic artery to parenchyma enhancement ratio were regarded as potential determining factors.ResultsTumors were depicted in 125 (88.0 %) and 142 tumors (100 %) on MIP and MIP + MPR analysis, respectively. Imaging performances on MIP and MIP + MPR analysis were good enough to perform subsegmental chemoembolization without additional angiographic investigation in 88 (62.0 %) and 128 tumors (90.1 %) on per-tumor basis and in 43 (50 %) and 73 (84.9 %) on per-patient basis, respectively. Significant determining factors for performance in MIP + MPR analysis on per tumor basis were tumor size (p = 0.030), tumor enhancement (0.005), tumor location (p = 0.001), and diaphragmatic motion (p < 0.001).ConclusionsCBCT hepatic arteriography provided sufficient information for subsegmental chemoembolization by depicting tumors and their feeders in the vast majority of patients. Combined analysis of MIP and MPR images was essential to enhance the performance of CBCT hepatic arteriography.

  12. Flow visualization study of two-phase flow in a single bend outlet feeder pipe of a CANDU reactor

    International Nuclear Information System (INIS)

    Savalaxs, S.-A.; Lister, D.H.; Steward, F.R.

    2005-01-01

    In CANDU reactors, the feeder piping that is used to direct the high-temperature water coolant between the fuel channels and the steam generators is made of carbon steel. Since 1996, several CANDU stations have reported excessive corrosion of their outlet feeders. The first metre is particularity vulnerable because the piping there consists of single or double bends, which have relatively thin walls produced by the bending process. Early studies related the attack to the hydrodynamics of the coolant and verified that it was a type of flow-accelerated corrosion. In order to understand the hydrodynamics of the coolant in the outlet feeders by flow visualization, a full-scale transparent test section simulating the geometry and orientation of an outlet feeder bend with its upstream components was fabricated. The feeder consisted of a 54 mm diameter acrylic pipe with a 73 degree bend. This was connected to the upstream component with an acrylic simulation of a Grayloc flanged fitting. A test loop supplied room temperature water to the test section at flow rates up to 0.019 m3/s. Air could be injected into the water to give a mean volume fraction of up to 0.56. In this preliminary investigation, the size and velocity of air bubbles at different flow conditions and their distribution within the pipe bend were studied. Particular attention was paid to the flow pattern at the inside of the bend, where a CFD (computational fluid dynamics) code - Fluent 6.1-had failed to predict a liquid film in an earlier study. A high-speed digital video camera was used to determine the relation between bubble size and velocity. Such a relation should help to explain the discrepancy in the CFD modelling and provide the basis for accurate predictions of phase distribution in complex geometries at high flow rates. (authors)

  13. Effect of artificial feeders on pollen loads of the hummingbirds of Cerro de La Muerte, Costa Rica

    Directory of Open Access Journals (Sweden)

    Gerardo Avalos

    2012-03-01

    Full Text Available Although sugar-water feeders are commonly used by enthusiasts to attract hummingbirds, little is known about how they affect hummingbird behavior and flower use. We studied the highland hummingbird assemblage of Cerro de La Muerte, Costa Rica, both at a site with permanent feeders (La Georgina Restaurant and further from it. We examined how feeder use and monopolization affected seasonal changes in pollen loads during four sampling periods, including dry and wet seasons, from 2003-2005. We expected that species monopolizing the feeders would carry little or no pollen whatsoever, and would have pollen loads characterized by low floral diversity, in contrast with species less dependent on feeders. We obtained pollen samples from 183 individuals of four hummingbird species captured around the feeders using mist nets, which were compared with a pollen reference collection of plants with a pollination syndrome by hummingbirds. The same methods were implemented at a site 3km away from the feeders. Feeder usage was quantified by counting the number of times hummingbirds drank from the feeders in periods of 4min separated by 1min. The effects of hummingbird species and season on pollen load categories were assessed using a nominal logistic regression. The alpha species at the site, the Fiery-throated Hummingbird (Panterpe insignis, dominated the feeders during the dry season. Meanwhile, in the wet season, feeder usage was more evenly distributed across species, with the exception of the Volcano Hummingbird, Selasphorus flammula, which occupies the last place in the dominance hierarchy. Pollen loads of hummingbirds captured near feeders were low in abundance (more than 50% of captured individuals had zero or low pollen loads, and low in species richness (96% of the hummingbirds with pollen from only one plant genus, Centropogon. Overall pollen loads increased during the dry season coinciding with peaks in flower availability, although the majority of

  14. Exogenous deposits

    International Nuclear Information System (INIS)

    Khasanov, A.Kh.

    1988-01-01

    Exogenous deposits forming as a result of complex exogenous processes, passed under the influence of outside forces on the Earth surface. To them relate physical and chemical weathering, decomposition and decay of mineral masses, redistribution and transportation of material, forming and deposit of new minerals and ores steady on the earth surface conditions

  15. Broadband non-selective excitation of plutonium isotopes for isotope ratio measurements in resonance ionization mass spectrometry: a theoretical study.

    Science.gov (United States)

    Sankari, M

    2012-10-15

    Making isotope ratio measurements with minimum isotope bias has always been a challenging task to mass spectrometrists, especially for the specific case of plutonium, owing to the strategic importance of the element. In order to use resonance ionization mass spectrometry (RIMS) as a tool for isotope ratio measurements, optimization of the various laser parameters and other atomic and system parameters is critical to minimize isotopic biases. Broadband simultaneous non-selective excitation of the isotopes of plutonium in the triple resonance excitation scheme with λ(1) = 420.77 nm, λ(2) = 847.28 nm, and λ(3) = 767.53 nm based on density matrix formalism has been theoretically computed for the determination of isotope ratios. The effects of the various laser parameters and other factors such as the atomization temperature and the dimensions of the atomic beam on the estimation of isotope ratios were studied. The effects of Doppler broadening, and time-dependent excitation parameters such as Rabi frequencies, ionization rate and the effect of non-Lorenztian lineshape have all been incorporated. The average laser powers and bandwidths for the three-excitation steps were evaluated for non-selective excitation. The laser intensity required to saturate the three-excitation steps were studied. The two-dimensional lineshape contour and its features were investigated, while the reversal of peak asymmetry of two-step and two-photon excitation peaks under these conditions is discussed. Optimized powers for the non-selective ionization of the three transitions were calculated as 545 mW, 150 mW and 545 mW and the laser bandwidth for all the three steps was ~20 GHz. The isotopic bias between the resonant and off-resonant isotope under the optimized conditions was no more than 9%, which is better than an earlier reported value. These optimized laser power and bandwidth conditions are better than in the earlier experimental work since these comprehensive calculations yield

  16. Field evaluation of cutter and feeder mechanism of chickpea harvester for lentil harvesting

    Directory of Open Access Journals (Sweden)

    S Kamgar

    2016-09-01

    Full Text Available Introduction The main producers of lentil are Canada, India, Nepal and China, respectively and Iran is the ninth producer in the world. The hand pulling is the usual method of lentil harvesting. Use of conventional combine because of short leg varieties, wide combine head in dry land and grain losses by cutter bar vibrations is impossible. So a mechanism should be designed to harvest the lentil plants with minimum damage. This mechanism should be evaluated under different tests of crop and machines such as forward speed (FS, grain moisture content (GMC, different varieties and other parameters. Some researchers studied the effects of GMC (Andrews and et al., 1993; Huitink, 2005; Adisa, 2009; Abdi and Jalali, 2013 and FS on grain losses (Geng et al., 1984; Swapan et al., 2001; Mostafavand and Kamgar, 2014; Hunt, 1995. Field tests were conducted at three levels of FS 1.5, 3 and 4.5 km.h-1; three levels of cutting height (CH 4, 8 and 13 cm and two levels of GMC, 8 and 14% on two varieties of lentils including Flip and Shiraz with three replications. Materials and Methods The feeder and cutter mechanism for chickpea harvesting that was the base design of device which is notched wheel and counter shear, was used. The other components of device were dividers, slat and chain feeders, belt and pulleys, chassis, elevator conveyor and storage. Two split plot design based on a randomized complete design was used to determine the effects of above treatments on lentil losses. Results and Discussion The ANOVA results indicated that the all studied factors; FS of feeder and cutter mechanism, CH and GMC had significant effect on losses of Shiraz variety (P0.05. The ranges of losses of Flip variety at 8% GMC were 8.6 to 10% for FS of 1.5 km.h-1, 9.1 to 10.4% for FS of 3 km.h-1and 10.4 to 11.4% for FS of 4.5 km h-1. These ranges at 14% GMC were 7.9 to 8.9% for FS of 1.5 km.h-1, 8.4 to 9.2% for FS of 3 km.h-1and 8.5 to 10% for FS of 4.5 km h-1. The ranges of

  17. Post-depositional tectonic modification of VMS deposits in Iberia and its economic significance

    Science.gov (United States)

    Castroviejo, Ricardo; Quesada, Cecilio; Soler, Miguel

    2011-07-01

    The original stratigraphic relationships and structure of VMS deposits are commonly obscured by deformation. This can also affect their economic significance, as shown by several Iberian Pyrite Belt (IPB, SW Iberia) examples. The contrasting rheologic properties of the different lithologies present in an orebody (massive sulphide, feeder stockwork, alteration envelope, volcanic and sedimentary rocks) play a major role in determining its overall behaviour. Variscan thin-skinned tectonics led to stacking of the massive pyrite and stockwork bodies in duplex structures, resulting in local thickening and increased tonnage of minable mineralization. Furthermore, differential mechanical behaviour of the different sulphide minerals localised the detachments along relatively ductile sulphide-rich bands. The result was a geochemical and mineralogical reorganisation of most deposits, which now consist of barren, massive pyrite horses, bounded by base metal-rich ductile shear zones. Metal redistribution was enhanced by mobilisation of the base metal sulphides from the initially impoverished massive pyrite, through pressure-solution processes, to tensional fissures within the already ductile shear zones. In NW Iberia, VMS deposits were also strongly overprinted by the Variscan deformation during emplacement of the Cabo Ortegal and Órdenes allochthonous nappe complexes, but no stacking of the orebodies was produced. Original contacts were transposed, and the orebodies, their feeder zones and the country rock acquired pronounced laminar geometry. In lower-grade rocks (greenschist facies, Cabo Ortegal Complex), solution transfer mechanisms are common in pyrite, which remains in the brittle domain, while chalcopyrite shows ductile behaviour. In higher-grade rocks (amphibolite facies, Órdenes Complex), metamorphic recrystallisation overprints earlier deformation textures. The contrasting behaviour of the IPB and NW Iberian deposits is explained by key factors that affect their

  18. Non-selective beta-adrenergic blockade prevents reduction of the cerebral metabolic ratio during exhaustive exercise in humans

    DEFF Research Database (Denmark)

    Larsen, T.S.; Rasmussen, P.; Overgaard, M.

    2008-01-01

    Intense exercise decreases the cerebral metabolic ratio of oxygen to carbohydrates [O(2)/(glucose + (1/2)lactate)], but whether this ratio is influenced by adrenergic stimulation is not known. In eight males, incremental cycle ergometry increased arterial lactate to 15.3 +/- 4.2 mm (mean +/- s.......d.) and the arterial-jugular venous (a-v) difference from -0.02 +/- 0.03 mm at rest to 1.0 +/- 0.5 mm (P cerebral metabolic ratio decreased from 5.5 +/- 1.4 to 3.0 +/- 0.3 (P ... of a non-selective beta-adrenergic (beta(1) + beta(2)) receptor antagonist (propranolol) reduced heart rate (69 +/- 8 to 58 +/- 6 beats min(-1)) and exercise capacity (239 +/- 42 to 209 +/- 31 W; P

  19. [Effects of prefrontal ablations on the reaction of the active choice of feeder under different probability and value of the reinforcement on dog].

    Science.gov (United States)

    Preobrazhenskaia, L A; Ioffe, M E; Mats, V N

    2004-01-01

    The role of the prefrontal cortex was investigated on the reaction of the active choice of the two feeders under changes value and probability reinforcement. The experiments were performed on 2 dogs with prefrontal ablation (g. proreus). Before the lesions the dogs were taught to receive food in two different feeders to conditioned stimuli with equally probable alimentary reinforcement. After ablation in the inter-trial intervals the dogs were running from the one feeder to another. In the answer to conditioned stimuli for many times the dogs choose the same feeder. The disturbance of the behavior after some times completely restored. In the experiments with competition of probability events and values of reinforcement the dogs chose the feeder with low-probability but better quality of reinforcement. In the experiments with equal value but different probability the intact dogs chose the feeder with higher probability. In our experiments the dogs with prefrontal lesions chose the each feeder equiprobably. Thus in condition of free behavior one of different functions of the prefrontal cortex is the reactions choose with more probability of reinforcement.

  20. Utilization of human amniotic mesenchymal cells as feeder layers to sustain propagation of human embryonic stem cells in the undifferentiated state.

    Science.gov (United States)

    Zhang, Kehua; Cai, Zhe; Li, Yang; Shu, Jun; Pan, Lin; Wan, Fang; Li, Hong; Huang, Xiaojie; He, Chun; Liu, Yanqiu; Cui, Xiaohui; Xu, Yang; Gao, Yan; Wu, Liqun; Cao, Shanxia; Li, Lingsong

    2011-08-01

    Human embryonic stem (ES) cells are usually maintained in the undifferentiated state by culturing on feeder cells layers of mouse embryonic fibroblasts (MEFs). However, MEFs are not suitable to support human ES cells used for clinical purpose because of risk of zoonosis from animal cells. Therefore, human tissue-based feeder layers need to be developed for human ES cells for clinical purpose. Hereof we report that human amniotic mesenchymal cells (hAMCs) could act as feeder cells for human ES cells, because they are easily obtained and relatively exempt from ethical problem. Like MEFs, hAMCs could act as feeder cells for human ES cells to grow well on. The self-renewal rate of human ES cells cultured on hAMCs feeders was higher than that on MEFs and human amniotic epithelial cells determined by measurement of colonial diameters and growth curve as well as cell cycle analysis. Both immunofluorescence staining and immunoblotting showed that human ES cells cultured on hAMCs expressed stem cell markers such as Oct-3/4, Sox2, and NANOG. Verified by embryoid body formation in vitro and teratoma formation in vivo, we found out that after 20 passages of culture, human ES cells grown on hAMCs feeders could still retain the potency of differentiating into three germ layers. Taken together, our data suggested hAMCs may be safe feeder cells to sustain the propagation of human ES cells in undifferentiated state for future therapeutic use.

  1. Effect of selective versus non-selective cyclooxygenase inhibitors on ischemia-reperfusion-induced hepatic injury in rats.

    Science.gov (United States)

    Abdel-Gaber, Seham A; Ibrahim, Mohamed A; Amin, Entesar F; Ibrahim, Salwa A; Mohammed, Rehab K; Abdelrahman, Aly M

    2015-08-01

    Ischemia-reperfusion (IR) injury represents an important pathological process of liver injury during major hepatic surgery. The role of cyclooxygenase (COX) enzymes in the pathogenesis of ischemia-reperfusion (IR)-induced liver injury is not clear. This study investigated the effect of a selective COX-2 inhibitor, celecoxib, versus non-selective, indomethacin, on hepatic IR injury in rats. Hepatic IR was induced in adult male rats. The animals were divided into 4 groups: normal control (sham group), IR non-treated group; IR-indomethacin-treated group; and IR-celecoxib-treated group. Liver injury was evaluated by serum alanine aminotransferase (ALT) and a histopathological examination of liver tissues. Hepatic tissue content of oxidative stress parameters glutathione peroxidase (GPx), superoxide dismutase (SOD), catalase, malondialdehyde (MDA), nitric oxide (NO) and the inflammatory marker, tumor necrosis factor-alpha, (TNF-α) were measured. Moreover, the immunohistochemical detection of endothelial NO synthase (eNOS), inducible NO synthase (iNOS), and caspase-3 in the hepatic tissue was performed. Celecoxib, but not indomethacin, significantly attenuated hepatic IR injury as evidenced by reduction in serum ALT as well as by improvement in the histopathological scoring. Such effect was associated with attenuation in oxidative stress and TNF-α, along with modulation of immunohistochemical expression of eNOS, iNOS and caspase-3 in the hepatic tissue. The present study concluded that selective COX-2 inhibition (but not non-selective), is hepatoprotective against liver IR injury; indicating a differential role of COX-1 versus COX-2. Modulation of iNOS, eNOS and caspase-3 might participate in the protective effect of selective COX-2-inhibitors. Copyright © 2015 Elsevier Inc. All rights reserved.

  2. Tricarbonyldichlororuthenium (II) dimer (CORM2) activates non-selective cation current in human endothelial cells independently of carbon monoxide releasing.

    Science.gov (United States)

    Dong, De-Li; Chen, Chang; Huang, Wei; Chen, Yan; Zhang, Xiao-Lan; Li, Zhe; Li, Yue; Yang, Bao-Feng

    2008-08-20

    Tricarbonyldichlororuthenium (II) dimer (CORM2) has been developed as carbon monoxide (CO) donor. We found that CORM2 activated a type of specific current which was distinct from the big-conductance Ca(2+)-activated K(+) current activated by CO in human umbilical vein endothelial cells (HUVECs). So the aim of the present study was to characterize the CORM2-induced current and to access the relation with CO releasing. CORM2 (100 microM) activated a kind of bi-directional current in HUVECs when the ramp protocol (holding potential 0 mV, from -120 mV to +120 mV) was applied. The current was not blocked by apamin, TRAM-34 and iberiotoxin, the small, intermediate and big-conductance Ca(2+) -activated K(+) channel blockers, and it was not sensitive to the pipette solution chelated with EGTA. CORM2 still activated the current when the chloride in the pipette solution was substituted by equal mol gluconic acid. Substitution of the sodium in the bath with choline significantly reduced the current activated by CORM2. The current was regarded as the non-selective cation current. The current showed slightly inward rectifier property and was not sensitive to Gd(3+) (100 microM), La(3+) (10 microM) or 2-aminoethoxydiphenyl borate (100 microM). CO (10 microM), CORM3 (100, 200 microM) and RuCl(3) (100 microM) were used as controls and showed no effect of the current activation. In conclusion, CORM2 activated the non-selective cation current in HUVECs independently of its CO releasing.

  3. Using automated feeders to wean calves fed large amounts of milk according to their ability to eat solid feed.

    Science.gov (United States)

    de Passillé, Anne Marie; Rushen, Jeffrey

    2016-05-01

    Dairy calves weaned off milk at an early age show signs of hunger and can lose weight. We examined whether using automated feeders to wean calves according to individual voluntary solid feed intake reduced the effects of weaning. Female Holstein calves were housed in groups of 5 to 9. All calves were fed 12 L/d milk and ad libitum grain starter and hay from automated feeders immediately after grouping, and were allocated to 3 weaning strategies: (1) early-weaned (EW; n=14): weaning began on d 40, and milk allowance gradually decreased until weaning was complete on d 48; (2) late-weaned (LW; n=14): weaning began on d 80 and was completed on d 89; (3) weaned by starter intake (WSI; n=28): weaning began when calves consumed 200g/d of starter and was completed when the calves consumed 1,400g/d. Each day, the automated feeders recorded quantities of milk, starter, and hay eaten by all calves, as well as the frequency of visits to the milk feeder; we used unrewarded visit frequency as a sign of hunger. Body weights (BW) were recorded weekly. We estimated daily digestible energy (DE) intake for each calf based on the milk, hay, and starter consumed. Average daily gains (ADG) were expressed as percent of BW. For calves in WSI, weaning began at 54.7±18.9 d (mean ± SD) of age, the duration of weaning was 21.1±10.6 d, and weaning ended at 75.8±10.7 d of age. Both LW and WSI calves had better ADG from wk 3 to 13 than EW calves. Calves in the WSI group drank less milk and ate more starter than LW calves but had similar ADG. During the period of weaning, EW calves made more unrewarded visits to the milk feeder than LW and WSI calves. Three EW calves lost weight during weaning, whereas all LW and WSI calves gained weight. Calves differ greatly in when they begin to eat solid feed and how quickly they increase the intake in response to a decrease in milk allowance. An advantage of automated feeders is that calves can be weaned at variable ages depending on their ability and

  4. Challenges associated with the current processes for ultrasonic inspection of CANDU reactor feeder piping

    Energy Technology Data Exchange (ETDEWEB)

    Machowski, C. [Babcock & Wilcox Canada Ltd., Cambridge, Ontario (Canada)

    2012-07-01

    CANDU® PHT Feeder Piping is generally constructed from SA106 Grade B carbon steel, which is known to be susceptible to flow accelerated corrosion when exposed to certain environmental conditions. The configuration of the CANDU reactor promotes thinning of the inside surface of the pipe walls, predominantly at the outlet feeders. Inspection of this piping is currently conducted using ultrasonic techniques and is governed by the requirements established by the CANDU Owners Group (COG). There are many challenges associated with these inspections as a result of the complexity of the reactor piping configuration. Geometrical anomalies on the surface of the pipe and non-circular geometries at the tight radius bends hinder the performance of conventional ultrasonic techniques. This can cause lost signals in areas of interest, which in turn often results in rework in order to satisfy the inspection requirements and justify fitness for service of these components. There are also many inspection sites which have limited access due to physical restrictions on the reactor face; therefore in order to maximize the performance of an inspection campaign, it is paramount that the inspection personnel and the inspection technology be well integrated through training simulations prior to execution. These inspection challenges increase the complexity of the analysis process as ultrasonic signals get distorted and lost as a result of non-circular pipe geometries. In order to ensure a high level of integrity in the analysis results, a conservative process is utilized in which two analysts independently examine the data, and a third analyst reviews their results and submits the final call. A Data Management Software application (DMS) is used to input and store the three analysis results. Another important function of the DMS is to provide a communication link between the different work-groups associated with the inspection activities. The focus of this presentation discusses:

  5. On the preparation of fire-wood splitting machines equipped with feeder devices

    International Nuclear Information System (INIS)

    Jaeaeskelaeinen, M.

    1995-01-01

    As part of the Bionergy research programme, the TTS Institute's Department of Forestry conducted a study on firewood splitting machines manufactured by Bilke Oy and Peurala Oy. The said machines are the first of their kind in Finland to be equipped with a feeder device. The Bilke unit is fed by a conveyor belt arrangement while the Peurala unit is equipped with a feeder roll. In addition, both machine types are equipped with a conveyor belt discharging device (e.g. for discharging split wood directly into a trailer). The Bilke unit can also be operated on extraction racks in the woods as the stems due to be split are fed into it from the side and the conveyor discharges the split wood rearwards into the trailer. The trailer can be hooked onto the splitting unit's draw-hook. At the landing, the Bilke unit was used to split a total of 14.2 m 3 and the Peurala unit 8.0 m 3 of approx. 3-metrelong stems averaging 9 cm in diameter. In addition to this, the Bilke unit was used to split ca. 17 m 3 of 3.5 metre-long stems with on average diameter of ca. 6 cm; the stems were in bunches alongside the extraction racks. The person operating the machines for the purposes of this study was a 27-year- old forest worker. The mean productivity achieved at the landing when using the Bilke unit was 7.7 m 3 while that of the Peurala unit was 5.8 m 3 per effective hour. When operated in the woods, the productivity achieved with the Bilke unit (excluding felling-cross cutting-delimbing-bunching and forest haulage work) was 2.8 m 3 /h. When applying a productivity of 1.7 m 3 for felling-cross cutting- delimbing-bunching work and 5.5. m 3 for forest haulage, the entire harvesting chain's productivity was 0.9 m 3 per effective hour

  6. The effect of space allowance and cage size on laying hens housed in furnished cages, Part II: Behavior at the feeder

    Science.gov (United States)

    Widowski, T. M; Caston, L. J; Casey-Trott, T. M; Hunniford, M. E

    2017-01-01

    Abstract Standards for feeder (a.k.a. feed trough) space allowance (SA) are based primarily on studies in conventional cages where laying hens tend to eat simultaneously, limiting feeder space. Large furnished cages (FC) offer more total space and opportunities to perform a greater variety of behaviors, which may affect feeding behavior and feeder space requirements. Our objective was to determine the effects of floor/feeder SA on behavior at the feeder. LSL-Lite hens were housed in FC equipped with a nest, perches, and a scratch mat. Hens with SA of either 520 cm2 (Low; 8.9 cm feeder space/hen) or 748 cm2 (High; 12.8 cm feeder space/hen) per bird resulted in groups of 40 vs. 28 birds in small FC (SFC) and 80 vs. 55 in large FC (LFC). Chain feeders ran at 0500, 0800, 1100, 1400, and 1700 with lights on at 0500 and off at 1900 hours. Digital recordings of FC were scanned at chain feeder onset and every 15 min for one h after (5 scans × 5 feeding times × 2 d) to count the number of birds with their head in the feeder. All occurrences of aggressive pecks and displacements during 2 continuous 30-minute observations at 0800 h and 1700 h also were counted. Mixed model repeated analyses tested the effects of SA, cage size, and time on the percent of hens feeding, and the frequency of aggressive pecks and displacements. Surprisingly, the percent of birds feeding simultaneously was similar regardless of cage size (LFC: 23.0 ± 0.9%; SFC: 24.0 ± 1.0%; P = 0.44) or SA (Low: 23.8 ± 0.9%; High: 23.3 ± 1.0%; P = 0.62). More birds were observed feeding at 1700 h (35.3 ± 0.1%) than any at other time (P < 0.001). Feeder use differed by cage area (nest, middle, or scratch) over the d (P < 0.001). The frequency of aggressive pecks was low overall and not affected by SA or cage size. Frequency of displacements was also low but greater at Low SA (P = 0.001). There was little evidence of feeder competition at the Low SA in this study. PMID:29050409

  7. Feeders of free-roaming cats: personal characteristics, feeding practices and data on cat health and welfare in an urban setting of Israel

    Directory of Open Access Journals (Sweden)

    Idit eGunther

    2016-03-01

    Full Text Available Cat feeders serve as an important source of available food for free-roaming cats (FRC and can play a central role in providing data on FRC distribution, welfare, and health. Data on cat feeder personalities as well as a better understanding of their feeding practices offer relevance for decision making concerning FRC population control strategies. The current study surveyed 222 FRC feeders who responded to a municipal trap-neuter-return (TNR campaign in an Israeli central urban setting. The aim of the study was to describe their personal characteristics, feeding practices and the FRC populations they feed. Feeders were divided into four groups according to the number of cats they claimed to feed per day (group 1: fed up to five cats; group 2: fed six to 10 cats; group 3: fed 11-20 cats; group 4: fed ≥21 cats. Most feeders were women (81%, with a median age of 58 years (range 18-81. The feeders reported an overall feeding of 3,337 cats in 342 different feeding locations. Feeders of group 4 comprised of 15.31% (n=34 of all feeders, but fed 56% (n=1869 of the FRC in 37.42% (n=128 of the feeding locations. 'Heavy' feeders (groups 3 and 4 reported that they traveled significantly longer distances in order to feed the cats. Commercial dry food consisted of 90% of the food they provided, with 66% of them feeding once a day, with less food per cat per day than the other feeder groups. Interestingly, 'heavy' feeders were usually singles, had on average fewer siblings, a clear preference for owning cats as pets and lived in lower income neighborhoods. According to the feeders' reports on the FRC populations they fed, 69.7% (2325/3337 cats were neutered and 11.8% (395/3337 were kittens. In addition, they reported that 1.6% (54/3337 of the cats were limping, 2% (67/3337 suffered from a systemic disease, 4% (135/3337 had skin lesions, and 3.9% (130/3337 were suffering from a chronic disability. Abundance of kittens and morbidity rate were significantly and

  8. The effect of space allowance and cage size on laying hens housed in furnished cages, Part II: Behavior at the feeder.

    Science.gov (United States)

    Widowski, T M; Caston, L J; Casey-Trott, T M; Hunniford, M E

    2017-09-01

    Standards for feeder (a.k.a. feed trough) space allowance (SA) are based primarily on studies in conventional cages where laying hens tend to eat simultaneously, limiting feeder space. Large furnished cages (FC) offer more total space and opportunities to perform a greater variety of behaviors, which may affect feeding behavior and feeder space requirements. Our objective was to determine the effects of floor/feeder SA on behavior at the feeder. LSL-Lite hens were housed in FC equipped with a nest, perches, and a scratch mat. Hens with SA of either 520 cm2 (Low; 8.9 cm feeder space/hen) or 748 cm2 (High; 12.8 cm feeder space/hen) per bird resulted in groups of 40 vs. 28 birds in small FC (SFC) and 80 vs. 55 in large FC (LFC). Chain feeders ran at 0500, 0800, 1100, 1400, and 1700 with lights on at 0500 and off at 1900 hours. Digital recordings of FC were scanned at chain feeder onset and every 15 min for one h after (5 scans × 5 feeding times × 2 d) to count the number of birds with their head in the feeder. All occurrences of aggressive pecks and displacements during 2 continuous 30-minute observations at 0800 h and 1700 h also were counted. Mixed model repeated analyses tested the effects of SA, cage size, and time on the percent of hens feeding, and the frequency of aggressive pecks and displacements. Surprisingly, the percent of birds feeding simultaneously was similar regardless of cage size (LFC: 23.0 ± 0.9%; SFC: 24.0 ± 1.0%; P = 0.44) or SA (Low: 23.8 ± 0.9%; High: 23.3 ± 1.0%; P = 0.62). More birds were observed feeding at 1700 h (35.3 ± 0.1%) than any at other time (P Feeder use differed by cage area (nest, middle, or scratch) over the d (P feeder competition at the Low SA in this study. © The Author 2017. Published by Oxford University Press on behalf of Poultry Science Association.

  9. Advanced feeder-free generation of induced pluripotent stem cells directly from blood cells.

    Science.gov (United States)

    Trokovic, Ras; Weltner, Jere; Nishimura, Ken; Ohtaka, Manami; Nakanishi, Mahito; Salomaa, Veikko; Jalanko, Anu; Otonkoski, Timo; Kyttälä, Aija

    2014-12-01

    Generation of validated human induced pluripotent stem cells (iPSCs) for biobanking is essential for exploring the full potential of iPSCs in disease modeling and drug discovery. Peripheral blood mononuclear cells (PBMCs) are attractive targets for reprogramming, because blood is collected by a routine clinical procedure and is a commonly stored material in biobanks. Generation of iPSCs from blood cells has previously been reported using integrative retroviruses, episomal Sendai viruses, and DNA plasmids. However, most of the published protocols require expansion and/or activation of a specific cell population from PBMCs. We have recently collected a PBMC cohort from the Finnish population containing more than 2,000 subjects. Here we report efficient generation of iPSCs directly from PBMCs in feeder-free conditions in approximately 2 weeks. The produced iPSC clones are pluripotent and transgene-free. Together, these properties make this novel method a powerful tool for large-scale reprogramming of PBMCs and for iPSC biobanking. ©AlphaMed Press.

  10. Comparisons of benthic filter feeder communities before and after a large-scale capital dredging program.

    Science.gov (United States)

    Abdul Wahab, Muhammad Azmi; Fromont, Jane; Gomez, Oliver; Fisher, Rebecca; Jones, Ross

    2017-09-15

    Changes in turbidity, sedimentation and light over a two year large scale capital dredging program at Onslow, northwestern Australia, were quantified to assess their effects on filter feeder communities, in particular sponges. Community functional morphological composition was quantified using towed video surveys, while dive surveys allowed for assessments of species composition and chlorophyll content. Onslow is relatively diverse recording 150 sponge species. The area was naturally turbid (1.1 mean P 80 NTU), with inshore sites recording 6.5× higher turbidity than offshore localities, likely influenced by the Ashburton River discharge. Turbidity and sedimentation increased by up to 146% and 240% through dredging respectively, with corresponding decreases in light levels. The effects of dredging was variable, and despite existing caveats (i.e. bleaching event and passing of a cyclone), the persistence of sponges and the absence of a pronounced response post-dredging suggest environmental filtering or passive adaptation acquired pre-dredging may have benefited these communities. Copyright © 2017. Published by Elsevier Ltd.

  11. Real-time modeling and simulation of distribution feeder and distributed resources

    Science.gov (United States)

    Singh, Pawan

    The analysis of the electrical system dates back to the days when analog network analyzers were used. With the advent of digital computers, many programs were written for power-flow and short circuit analysis for the improvement of the electrical system. Real-time computer simulations can answer many what-if scenarios in the existing or the proposed power system. In this thesis, the standard IEEE 13-Node distribution feeder is developed and validated on a real-time platform OPAL-RT. The concept and the challenges of the real-time simulation are studied and addressed. Distributed energy resources include some of the commonly used distributed generation and storage devices like diesel engine, solar photovoltaic array, and battery storage system are modeled and simulated on a real-time platform. A microgrid encompasses a portion of an electric power distribution which is located downstream of the distribution substation. Normally, the microgrid operates in paralleled mode with the grid; however, scheduled or forced isolation can take place. In such conditions, the microgrid must have the ability to operate stably and autonomously. The microgrid can operate in grid connected and islanded mode, both the operating modes are studied in the last chapter. Towards the end, a simple microgrid controller modeled and simulated on the real-time platform is developed for energy management and protection for the microgrid.

  12. Feasibility assessment of optical technologies for reliable high capacity feeder links

    Science.gov (United States)

    Witternigg, Norbert; Schönhuber, Michael; Leitgeb, Erich; Plank, Thomas

    2013-08-01

    Space telecom scenarios like data relay satellite and broadband/broadcast service providers require reliable feeder links with high bandwidth/data rate for the communication between ground station and satellite. Free space optical communication (FSOC) is an attractive alternative to microwave links, improving performance by offering abundant bandwidth at small apertures of the optical terminals. At the same time Near-Earth communication by FSOC avoids interference with other services and is free of regulatory issues. The drawback however is the impairment by the laser propagation through the atmosphere at optical wavelengths. Also to be considered are questions of eye safety for ground personnel and aviation. In this paper we assess the user requirements for typical space telecom scenarios and compare these requirements with solutions using optical data links through the atmosphere. We suggest a site diversity scheme with a number of ground stations and a switching scheme using two optical terminals on-board the satellite. Considering the technology trade-offs between four different optical wavelengths we recommend the future use of 1.5 μm laser technology and calculate a link budget for an atmospheric condition of light haze on the optical path. By comparing link budgets we show an outlook to the future potential use of 10 μm laser technology.

  13. Controlling Voltage Levels of Distribution Network-Radial Feeder after Connecting Wind Turbines to the Network

    Directory of Open Access Journals (Sweden)

    Muhammad Al Badri

    2017-11-01

    Full Text Available Several factors in power generation and supply need to be taken into account such as shortages of energy supply, system stability, and energy quality and system disruption due to network losses, industrial development and population expansion. The addition of wind turbines to the distribution network is of great benefit in providing additional power and solving these problems, but this addition is accompanied by the problem of low voltage network. This research found optimal solutions to the problem of low voltage distribution network after connecting wind turbines. The main idea of this paper is to optimize the low-voltage problem as a result of connecting the wind turbines to the "far end" of the radial feeder for a distribution network and to obtain a voltage level within an acceptable and stable range. The problem of low voltage solved by using the load-drop compensation, capacitor-bank and “doubly-fed” induction generators. The results of this study were based on the operation of the entire design of the simulation system which would be compatible with the reality of the energy flow of all network components by using the PSCAD program. The present analysis program revealed an optimum solution for the low voltage profile of the distribution network after connecting the wind turbine.

  14. Utilisation of symmetrical components in a communication-based protection for loop MV feeders with variable short-circuit power

    DEFF Research Database (Denmark)

    Ciontea, Catalin-Iosif; Bak, Claus Leth; Blaabjerg, Frede

    2018-01-01

    -circuit power is presented. It relies on utilisation of symmetrical components of the short-circuit currents and on communication between the protection relays. The proposed method addresses the Single Phase to Ground (SPG) faults occurring in directly grounded distribution networks, with focus on closed......Variability of the available short-circuit power also implies variation of the fault level, which can potentially cause several protection problems in the electric networks. In this paper, a novel protection method that is insensitive to the fault level changes caused by variable short......-loop Medium Voltage (MV) feeders. Case studies are presented, which demonstrate that the proposed protection scheme is capable of effectively detecting the SPG faults in closed-loop feeders with variable short-circuit power....

  15. A Double-Resistive Active Power Filter System to Attenuate Harmonic Voltages of a Radial Power Distribution Feeder

    DEFF Research Database (Denmark)

    Sun, Xiaofeng; Han, Ruijing; Shen, Hong

    2016-01-01

    voltages. This paper proposes a double-resistive active power filter (D-RAPF) system consisting of a terminal-RAPF and an attenuation-RAPF for each individual harmonic. The terminal-RAPF operating as the characteristic impedance of the feeder is installed at the end bus to suppress harmonic propagation......Harmonic propagation between power-factor correction capacitors and system inductors seriously deteriorates power quality in a radial power distribution feeder. Installation of a resistive active power filter (RAPF) at the end bus only suppresses harmonic propagation, not attenuates harmonic...... at all harmonic frequencies. The attenuation-RAPF, whose control gain can be set according to the requirements of the harmonic voltage distortion limit, is installed at a specific position for each individual harmonic to attenuate the corresponding harmonic voltages. The D-RAPF system not only suppresses...

  16. Power Hardware-in-the-Loop Evaluation of PV Inverter Grid Support on Hawaiian Electric Feeders: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Austin; Prabakar, Kumaraguru; Nagarajan, Adarsh; Nepal, Shaili; Hoke, Anderson; Asano, Marc; Ueda, Reid; Ifuku, Earle

    2017-05-08

    As more grid-connected photovoltaic (PV) inverters become compliant with evolving interconnections requirements, there is increased interest from utilities in understanding how to best deploy advanced grid-support functions (GSF) in the field. One efficient and cost-effective method to examine such deployment options is to leverage power hardware-in-the-loop (PHIL) testing methods. Two Hawaiian Electric feeder models were converted to real-time models in the OPAL-RT real-time digital testing platform, and integrated with models of GSF capable PV inverters that were modeled from characterization test data. The integrated model was subsequently used in PHIL testing to evaluate the effects of different fixed power factor and volt-watt control settings on voltage regulation of the selected feeders. The results of this study were provided as inputs for field deployment and technical interconnection requirements for grid-connected PV inverters on the Hawaiian Islands.

  17. Derivation and characterization of the NIH registry human stem cell line NYSCF100 line under defined feeder-free conditions

    Directory of Open Access Journals (Sweden)

    Ana Sevilla

    2018-05-01

    Full Text Available The human embryonic stem cell line NYSCFe001-A was derived from a day 6 blastocyst in feeder-free and antibiotic free conditions. The blastocyst was voluntarily donated for research as surplus after in vitro fertilization treatment following informed consent. The NYSCFe001-A line, registered as NYSCF100 on the NIH registry, presents normal karyotype, is mycoplasma free, expresses all the pluripotency markers and has the potential to differentiate into all three germ layers in vitro.

  18. Effects of Home Energy Management Systems on Distribution Utilities and Feeders Under Various Market Structure; NREL (National Renewable Energy Laboratory)

    Energy Technology Data Exchange (ETDEWEB)

    Ruth, M.; Pratt, A.; Lunacek, M.; Mittal, S.; Wu, H.; Jones, W.

    2015-06-15

    The combination of distributed energy resources (DER) and retail tariff structures to provide benefits to both utility consumers and the utilities is not well understood. To improve understanding, an Integrated Energy System Model (IESM) is being developed to simulate the physical and economic aspects of DER technologies, the buildings where they reside, and feeders servicing them. The IESM was used to simulate 20 houses with home energy management systems on a single feeder under a time-of-use (TOU) tariff to estimate economic and physical impacts on both the households and the distribution utilities. Home energy management systems (HEMS) reduce consumers’ electric bills by precooling houses in the hours before peak electricity pricing. Utilization of HEMS reduce peak loads during high price hours but shifts it to hours with off-peak and shoulder prices, resulting in a higher peak load. used to simulate 20 houses with home energy management systems on a single feeder under a time-of-use (TOU) tariff to estimate economic and physical impacts on both the households and the distribution utilities. Home energy management systems (HEMS) reduce consumers’ electric bills by precooling houses in the hours before peak electricity pricing. Utilization of HEMS reduce peak loads during high price hours but shifts it to hours with off-peak and shoulder prices, resulting in a higher peak load.

  19. Differences in carotenoid accumulation among three feeder-cricket species: implications for carotenoid delivery to captive insectivores.

    Science.gov (United States)

    Ogilvy, Victoria; Fidgett, Andrea L; Preziosi, Richard F

    2012-01-01

    There are a limited number of feeder-invertebrates available to feed captive insectivores, and many are deficient in certain nutrients. Gut-loading is used to increase the diversity of nutrients present in the captive insectivore diet; however, little is known about delivery of carotenoids via gut-loading. Carotenoids may influence health and reproduction due to their roles in immune and antioxidant systems. We assessed interspecific variation in carotenoid accumulation and retention in three feeder-cricket species (Gryllus bimaculatus, Gryllodes sigillatus and Acheta domesticus) fed one of three diets (wheat-bran, fish-food based formulated diet, and fresh fruit and vegetables). Out of the three species of feeder-cricket in the fish-food-based dietary treatment group, G. bimaculatus had the greatest total carotenoid concentration. All cricket species fed the wheat-bran diet had very low carotenoid concentrations. Species on the fish-food-based diet had intermediate carotenoid concentrations, and those on the fruit and vegetable diet had the highest concentrations. Carotenoid retention was poor across all species. Overall, this study shows that, by providing captive insectivores with G. bimaculatus crickets recently fed a carotenoid-rich diet, the quantity of carotenoids in the diet can be increased. © 2011 Wiley Periodicals, Inc.

  20. Optimal distribution feeder reconfiguration for increasing the penetration of plug-in electric vehicles and minimizing network costs

    International Nuclear Information System (INIS)

    Kavousi-Fard, Abdollah; Abbasi, Alireza; Rostami, Mohammad-Amin; Khosravi, Abbas

    2015-01-01

    Appearance of PEVs (Plug-in Electric Vehicles) in future transportation sector brings forward opportunities and challenges from grid perspective. Increased utilization of PEVs will result in problems such as greater total loss, unbalanced load factor, feeder congestion and voltage drop. PEVs are mobile energy storages dispersed all over the network with benefits to both owners and utilities in case of V2G (Vehicle-to-Grid) possibility. The intelligent bidirectional power flow between grid and large number of vehicles adds complexity to the system and requires operative tools to schedule V2G energy and subdue PEV impacts. In this paper, DFR (Distribution Feeder Reconfiguration) is utilized to optimally coordinate PEV operation in a stochastic framework. Uncertainty in PEVs characteristics can be due to several sources from location and time of grid connection to driving pattern and battery SoC (State-of-Charge). The proposed stochastic problem is solved with a self-adaptive evolutionary swarm algorithm based on SSO (Social Spider Optimization) algorithm. Numerical studies verify the efficacy of the proposed DFR to improve the system performance and optimal dispatch of V2G. - Highlights: • Consideration effect of PEVS on the distribution feeder reconfiguration. • Increasing the penetration of PEVS. • Introducing a new artificial optimization algorithm. • Modeling the uncertainty in network. • Investigating the degradation cost of batteries in V2G technology.

  1. Cool Down Experiences with the SST-1 Helium Cryogenics System before and after Current Feeders System Modification

    Science.gov (United States)

    Patel, R.; Panchal, P.; Panchal, R.; Tank, J.; Mahesuriya, G.; Sonara, D.; Srikanth, G. L. N.; Garg, A.; Bairagi, N.; Christian, D.; Patel, K.; Shah, P.; Nimavat, H.; Sharma, R.; Patel, J. C.; Gupta, N. C.; Prasad, U.; Sharma, A. N.; Tanna, V. L.; Pradhan, S.

    The SST-1 machine comprises a superconducting magnet system (SCMS), which includes TF and PF magnets. In order to charge the SCMS, we need superconducting current feeders consisting of SC feeders and vapor cooled current leads (VCCLs). We have installed all 10 (+/-) pairs of VCCLs for the TF and PF systems. While conducting initial engineering validation of the SST-1 machine, our prime objective was to produce circular plasma using only the TF system. During the SST-1 campaign I to VI, we have to stop the PF magnets cooling in order to get the cryo- stable conditions for current charging of the TF magnets system. In that case, the cooling of the PF current leads is not essential. It has been also observed that after aborting the PF system cooling, there was a limited experimental window of TF operation. Therefore, in the recent SST-1 campaign-VII, we removed the PF current leads (9 pairs) and kept only single (+/-) pair of the 10,000 A rated VCCLs to realize the charging of the TF system for the extended window of operation. We have observed a better cryogenic stability in the TF magnets after modifications in the CFS. In this paper, we report the comparison of the cool down performance for the SST-1 machine operation before and after modifications of the current feeders system.

  2. Busbar arcs at large fusion magnets: Conductor to feeder tube arcing model experiments with the LONGARC device

    Energy Technology Data Exchange (ETDEWEB)

    Klimenko, Dmitry, E-mail: dmitry.klimenko@kit.edu; Pasler, Volker

    2014-10-15

    Highlights: •The LONGARC device was successfully implemented for busbar to feeder tubes arcing model experiments. •Arcing at an ITER busbar inside its feeder tube was simulated in scaled model experiments. •The narrower half tubes imply a slight increase of the arc propagation speed in compare to full tube experiments. •All simulated half tubes experiments show severe damage indicating that the ITER inner feeder tube will not withstand a busbar arc. -- Abstract: Electric arcs moving along the power cables (the so-called busbars) of the toroidal field (TF) coils of ITER may reach and penetrate the cryostat wall. Model experiments with the new LONGARC device continue the VACARC (VACuum ARC) experiments that were initiated to investigate the propagation and destruction mechanisms of busbar arcs in small scale [1]. The experiments are intended to support the development and validation of a numerical model. LONGARC overcomes the space limitations inside VACARC and allows also for advanced 1:3 (vs. ITER full scale) model setups. The LONGARC device and first results are presented below.

  3. Water quality in Pearl Harbor and feeder streams during 1971 - 2001 collected primarily by oceanography students from Leeward Community College (NODC Accession 0000590)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Water quality data were collected in Pearl Harbor and surrounding feeder streams from 30 December 1971 to 24 August 2001. Data were collected by Leeward Community...

  4. Forward selection for multiple resistance across the non-selective glyphosate, glufosinate and oxyfluorfen herbicides in Lolium weed species.

    Science.gov (United States)

    Fernández, Pablo; Alcántara, Ricardo; Osuna, María D; Vila-Aiub, Martin M; Prado, Rafael De

    2017-05-01

    In the Mediterranean area, Lolium species have evolved resistance to glyphosate after decades of continual use without other alternative chemicals in perennial crops (olive, citrus and vineyards). In recent years, oxyfluorfen alone or mixed with glyphosate and glufosinate has been introduced as a chemical option to control dicot and grass weeds. Dose-response studies confirmed that three glyphosate-resistant Lolium weed species (L. rigidum, L. perenne, L. multiflorum) collected from perennial crops in the Iberian Peninsula have also evolved resistance to glufosinate and oxyfluorfen herbicides, despite their recent introduction. Based on the LD 50 resistance parameter, the resistance factor was similar among Lolium species and ranged from 14- to 21-fold and from ten- to 12-fold for oxyfluorfen and glufosinate respectively. Similarly, about 14-fold resistance to both oxyfluorfen and glufosinate was estimated on average for the three Lolium species when growth reduction (GR 50 ) was assessed. This study identified oxyfluorfen resistance in a grass species for the first time. A major threat to sustainability of perennial crops in the Iberian Peninsula is evident, as multiple resistance to non-selective glyphosate, glufosinate and oxyfluorfen herbicides has evolved in L. rigidum, L. perenne and L. multiflorum weeds. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  5. Cardiac protein expression patterns are associated with distinct inborn exercise capacity in non-selectively bred rats

    Directory of Open Access Journals (Sweden)

    L.P. Ribeiro

    2018-01-01

    Full Text Available In the present study, we successfully demonstrated for the first time the existence of cardiac proteomic differences between non-selectively bred rats with distinct intrinsic exercise capacities. A proteomic approach based on two-dimensional gel electrophoresis coupled to mass spectrometry was used to study the left ventricle (LV tissue proteome of rats with distinct intrinsic exercise capacity. Low running performance (LRP and high running performance (HRP rats were categorized by a treadmill exercise test, according to distance run to exhaustion. The running capacity of HRPs was 3.5-fold greater than LRPs. Protein profiling revealed 29 differences between HRP and LRP rats (15 proteins were identified. We detected alterations in components involved in metabolism, antioxidant and stress response, microfibrillar and cytoskeletal proteins. Contractile proteins were upregulated in the LVs of HRP rats (α-myosin heavy chain-6, myosin light chain-1 and creatine kinase, whereas the LVs of LRP rats exhibited upregulation in proteins associated with stress response (aldehyde dehydrogenase 2, α-crystallin B chain and HSPβ-2. In addition, the cytoskeletal proteins desmin and α-actin were upregulated in LRPs. Taken together, our results suggest that the increased contractile protein levels in HRP rats partly accounted for their improved exercise capacity, and that proteins considered risk factors to the development of cardiovascular disease were expressed in higher amounts in LRP animals.

  6. Changes in food intake and abnormal behavior using a puzzle feeder in newly acquired sub-adult rhesus monkeys (Macaca mulatta): a short term study.

    Science.gov (United States)

    Lee, Jae-Il; Lee, Chi-Woo; Kwon, Hyouk-Sang; Kim, Young-Tae; Park, Chung-Gyu; Kim, Sang-Joon; Kang, Byeong-Cheol

    2008-10-01

    The majority of newly acquired nonhuman primates encounter serious problems adapting themselves to new environments or facilities. In particular, loss of appetite and abnormal behavior can occur in response to environmental stresses. These adaptation abnormalities can ultimately have an affect on the animal's growth and well-being. In this study, we evaluated the affects of a puzzle feeder on the food intake and abnormal behavior of newly acquired rhesus monkeys for a short period. The puzzle feeder was applied to 47- to 58-month-old animals that had never previously encountered one. We found that there was no difference in the change of food intake between the bucket condition and the puzzle feeder condition. In contrast, the time spent for consumption of food was three times longer in the puzzle feeder condition than in the bucket condition. Two monkeys initially exhibited stereotypic behavior. One showed a decreasing, and the other an increasing pattern of abnormal behavior after introduction of the puzzle feeder. In conclusion, this result suggests that over a short period, the puzzle feeder can only affect the time for food consumption since it failed to affect the food intake and did not consistently influence stereotypic behaviors in newly acquired rhesus monkeys.

  7. Adjusting the weaning age of calves fed by automated feeders according to individual intakes of solid feed.

    Science.gov (United States)

    de Passillé, A M; Rushen, J

    2012-09-01

    When weaned at the ages typical of commercial dairy production, dairy calves usually show reduced growth rates, lowered energy intake, and increased behavioral signs of hunger, reflecting their difficulty in switching from a milk diet to solid feed. However, large differences exist between calves in their ability to adapt to solid feed, and automated feeders allow the age of weaning to be adjusted to an individual calf's intake of solid feed. We examined the effects of weaning according to solid feed intake on age at weaning, feed intake, and behavioral signs of hunger. In a 2×2 factorial design, 60 female Holstein calves in groups of 8 and fed milk, grain starter, and hay from automated feeders began to be weaned when their voluntary intake of grain starter was either 400 g/d (high start) or 200 g/d (low start), with weaning completed when their voluntary intakes of starter were either 1,600 g/d (high end) or 800 g/d (low end). Digestible energy intakes were calculated from milk, starter and hay intakes, corrected for body weights, calves were weighed, and the frequency of visits to the milk feeders were measured each day. The main effects and interactions between treatments were tested with ANOVA. Large differences were observed between calves in the age at which weaning was complete, with weaning completed earlier for low-end calves compared with high-end calves. No treatment effects (either of start amount or end amount) on intakes of milk, starter, or hay or on weight gains occurred. However, the calves that began weaning earlier had longer durations of weaning, greater growth rates from d 20 to 87, and were heavier on d 87, and had lower milk intakes, higher starter intakes, higher hay intakes, and a greater digestible energy intake, but showed more unrewarded visits to the milk feeder. Adjusting the age at which individual calves are weaned off milk according to their ability to eat solid feed can reduce the age at which weaning occurs while reducing the

  8. The filter feeder Dreissena polymorpha affects nutrient, silicon, and metal(loid) mobilization from freshwater sediments.

    Science.gov (United States)

    Schaller, Jörg; Planer-Friedrich, Britta

    2017-05-01

    Organic sediments in aquatic ecosystems are well known sinks for nutrients, silicon, and metal(loid)s. Organic matter-consuming organisms like invertebrate shredders, grazers, and bioturbators significantly affect element fixation or remobilization by changing redox conditions or binding properties of organic sediments. Little is known about the effect of filter feeders, like the zebra mussel Dreissena polymorpha, an invasive organism in North American and European freshwater ecosystems. A laboratory batch experiment exposing D. polymorpha (∼1200 organisms per m 2 ) to organic sediment from a site contaminated with arsenic, copper, lead, and uranium revealed a significant uptake and accumulation of arsenic, copper, iron, and especially uranium both into the soft body tissues and the seashell. This is in line with previous observations of metal(loid) accumulation from biomonitoring studies. Regarding its environmental impact, D. polymorpha significantly contributed to mobilization of silicon, iron, phosphorus, arsenic, and copper and to immobilization of uranium (p < 0.001), probably driven by redox conditions, microbial activity within the gut system, or active control of element homeostasis. No net mobilization or immobilization was observed for zinc and lead, because of their low mobility at the prevailing pH of 7.5-8.5. The present results suggest that D. polymorpha can both ameliorate (nutrient mobilization, immobilization of toxicants mobile under oxic conditions) or aggravate negative effects (mobilization of toxicants mobile under reducing conditions) in ecosystems. Relating the results of the present study to observed population densities in natural freshwater ecosystems suggests a significant influence of D. polymorpha on element cycling and needs to be considered in future studies. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. Uptake, accumulation, and biotransformation of metal oxide nanoparticles by a marine suspension-feeder

    International Nuclear Information System (INIS)

    Montes, Milka O.; Hanna, Shannon K.; Lenihan, Hunter S.; Keller, Arturo A.

    2012-01-01

    Highlights: ► Suspension-feeding by mussels can greatly alter mobility and fate of metal oxide nanoparticles. ► Bioprocessing of metal oxide nanoparticles by mussels removes large fraction from water column. ► Mussels repackage metal oxide nanoparticles in highly concentrated pseudofeces. ► Novel biological pathway between major compartments in marine systems. ► Very different outcome for ZnO and CeO 2 nanoparticles based on their solubility. - Abstract: A growing body of evidence indicates that some engineered nanoparticles (ENPs) are toxic to organisms that perform important ecosystem services in terrestrial and aquatic ecosystems. However, toxicity can be influenced by the biotransformation of contaminants, including ENPs, as it may alter the fate and transport of these substances. In turn, fate and transport can influence their bioavailability. To understand how biotransformation influences the fate and transport of ENPs in marine ecosystems, we exposed suspension-feeding mussels, Mytilus galloprovincialis, to two common nano-metal oxides, CeO 2 and ZnO, over a range of concentrations from 1 mg L −1 to 10 mg L −1 , in a laboratory experiment. Mussels exposed to 10 mg L −1 accumulated 62 μg g −1 of Ce and 880 μg g −1 of Zn on a dry tissue basis but rejected 21,000 μg g −1 for Ce and 63,000 μg g −1 for Zn in pseudofeces. Scanning electron microscope evidence indicates CeO 2 remained as ENPs but ZnO did not after being rejected by the mussels. Mussels filtered most of the CeO 2 from the aqueous media, while a significant fraction of Zn remained in solution. Differences in ENP solubility affect ENP uptake, excretion, and accumulation in mussels. Our study highlights the potential role of marine suspension feeders in biotransformation of ENPs.

  10. Does proximity to urban centres affect the dietary regime of marine benthic filter feeders?

    Science.gov (United States)

    Puccinelli, Eleonora; Noyon, Margaux; McQuaid, Christopher D.

    2016-02-01

    Threats to marine ecosystems include habitat destruction and degradation of water quality, resulting from land- and ocean-based human activities. Anthropogenic input causing modification of water quality, can affect primary productivity and thus food availability and quality for higher trophic levels. This is especially important for sedentary benthic intertidal communities, which rely on local food availability. We investigated the effect of urbanization on the dietary regime of four species of intertidal filter feeders (three barnacles and one mussel) at sites close to high-density cities and at sites far from heavily urbanized areas using fatty acid and stable isotope techniques. δ15N was significantly higher at urbanized sites compared to their corresponding control sites for all species with few exceptions, while no effect on δ13C was recorded. Barnacle fatty acid profiles were not affected by cities, while mussels from sites close to cities had fatty acid signatures with a higher proportion of polyunsaturated fatty acids (PUFA). We suggest that the enrichment in δ15N at urbanised sites reflects the influence of anthropogenically derived nitrogen directly linked to wastewater input from domestic and industrial sewage. Linked to this, the high proportion of PUFA in mussels at urbanized sites may reflect the influence of increased nitrogen concentrations on primary production and enhanced growth of large phytoplankton cells. The results indicate that anthropogenic effects can strongly influence the diets of benthic organisms, but these effects differ among taxa. Changes in the diet of such habitat forming species can affect their fitness and survival with potential effects on the populations associated with them.

  11. Non-selective regulation of peroxide and superoxide resistance genes by PerR in Campylobacter jejuni

    Directory of Open Access Journals (Sweden)

    Jong-Chul eKim

    2015-02-01

    Full Text Available Campylobacter jejuni is an important foodborne pathogen. The molecular mechanisms for the regulation of oxidative stress resistance have not yet been understood fully in this bacterium. In this study, we investigated how PerR (peroxide stress regulator modulates the transcriptional regulation of both peroxide and superoxide resistance genes in C. jejuni, particularly under oxidative stress conditions. The transcriptional levels of ahpC, katA, and sodB were substantially increased by aeration and oxidant exposure. Interestingly, a perR mutation completely abrogated the transcriptional response of ahpC, katA and sodB to oxidants. Furthermore, we demonstrated that perR transcription was reduced by aeration and oxidant exposure. In contrast to the unique role of PerR homologs in peroxide stress regulation in other bacteria, interestingly, C. jejuni PerR directly regulates the transcription of sodB, the most important gene in superoxide defense, as evidenced by the alteration of sodB transcription by the perR mutation and direct binding of rPerR to the sodB promoter. In addition, we also observed notable morphological changes in C. jejuni from spiral rods to coccoid morphology under aerobic conditions. Based on the intracellular ATP levels, C. jejuni entered a viable-but-non-culturable state under aerobic conditions. These findings clearly demonstrate that C. jejuni possesses a unique regulatory mechanism of oxidative stress defense that does not specifically distinguish between peroxide and superoxide defense, and PerR plays a pivotal role in this non-selective regulation of oxidative stress resistance in C. jejuni.

  12. The incentive amplifying effects of nicotine are reduced by selective and non-selective dopamine antagonists in rats.

    Science.gov (United States)

    Palmatier, Matthew I; Kellicut, Marissa R; Brianna Sheppard, A; Brown, Russell W; Robinson, Donita L

    2014-11-01

    Nicotine is a psychomotor stimulant with 'reinforcement enhancing' effects--the actions of nicotine in the brain increase responding for non-nicotine rewards. We hypothesized that this latter effect of nicotine depends on increased incentive properties of anticipatory cues; consistent with this hypothesis, multiple laboratories have reported that nicotine increases sign tracking, i.e. approach to a conditioned stimulus (CS), in Pavlovian conditioned-approach tasks. Incentive motivation and sign tracking are mediated by mesolimbic dopamine (DA) transmission and nicotine facilitates mesolimbic DA release. Therefore, we hypothesized that the incentive-promoting effects of nicotine would be impaired by DA antagonists. To test this hypothesis, separate groups of rats were injected with nicotine (0.4mg/kg base) or saline prior to Pavlovian conditioning sessions in which a CS (30s illumination of a light or presentation of a lever) was immediately followed by a sweet reward delivered in an adjacent location. Both saline and nicotine pretreated rats exhibited similar levels of conditioned approach to the reward location (goal tracking), but nicotine pretreatment significantly increased approach to the CS (sign tracking), regardless of type (lever or light). The DAD1 antagonist SCH-23390 and the DAD2/3 antagonist eticlopride reduced conditioned approach in all rats, but specifically reduced goal tracking in the saline pretreated rats and sign tracking in the nicotine pretreated rats. The non-selective DA antagonist flupenthixol reduced sign-tracking in nicotine rats at all doses tested; however, only the highest dose of flupenthixol reduced goal tracking in both nicotine and saline groups. The reductions in conditioned approach behavior, especially those by SCH-23390, were dissociated from simple motor suppressant effects of the antagonists. These experiments are the first to investigate the effects of dopaminergic drugs on the facilitation of sign-tracking engendered by

  13. Bioaccumulation, toxicokinetics, and effects of copper from sediment spiked with aqueous Cu, nano-CuO, or micro-CuO in the deposit-feeding snail, Potamopyrgus antipodarum

    DEFF Research Database (Denmark)

    Pang, Chengfang; Selck, Henriette; Banta, Gary Thomas

    2013-01-01

    The present study examined the relative importance of copper (aqueous Cu and CuO particles of different sizes) added to sediment to determine the bioaccumulation, toxicokinetics, and effects in the deposit feeder Potamopyrgus antipodarum. In experiment 1, the bioaccumulation of Cu (240 mg Cu/g dr...

  14. Effect of concentrate feeder design on performance, eating and animal behavior, welfare, ruminal health, and carcass quality in Holstein bulls fed high-concentrate diets.

    Science.gov (United States)

    Verdú, M; Bach, A; Devant, M

    2015-06-01

    A total of 240 Holstein bulls (121 ± 2.0 kg initial BW; 99 ± 1.0 d of age), from 2 consecutive fattening cycles, were randomly allocated in 1 of 6 pens and assigned to 1 of the 3 treatments consisting of different concentrate feeder designs: a control feeder with 4 feeding spaces (CF), a feeder with less concentrate capacity (CFL), and a single-space feeder with lateral protections (SF). Each pen had a straw feeder and a drinker. All animals were fed a high-concentrate diet for ad libitum intake. Concentrate consumption was recorded daily using a computerized feeder, straw consumption was recorded weekly, and BW was recorded every 14 d. Animal behavior was registered on d 1, 3, 5, 8, and 14 and every 28 d by scan sampling. Eating behavior at concentrate feeders was filmed on d 12, 125, and 206. On d 7, 120, and 204, samples of rumen contents were collected for measurement of pH and VFA and blood samples were obtained to analyze NEFA, haptoglobin, glucose, and insulin. Animals were slaughtered after 223 d, and HCW and lesions of the rumen wall and liver were recorded. The accumulative concentrate consumption per animal tended (P = 0.09) to be greater with CF than with CFL and SF. Also, CV of concentrate consumption was greater (P carcass data. Also, no differences among treatments in rumen wall evaluation and liver abscesses were observed. At 7 and 204 d of study, SF bulls had greater (P animal welfare in Holstein bulls fed high-concentrate diets. However, at the beginning, there was evidence that animals fed using SF had problems with adaptation.

  15. Uptake, accumulation, and biotransformation of metal oxide nanoparticles by a marine suspension-feeder

    Energy Technology Data Exchange (ETDEWEB)

    Montes, Milka O. [University of California Center for Environmental Implications of Nanotechnology, Bren School of Environmental Science and Management, University of California, Santa Barbara, CA 93106 (United States); University of Texas of the Permian Basin, 4901 E. University, Odessa, TX 79762 (United States); Hanna, Shannon K.; Lenihan, Hunter S. [University of California Center for Environmental Implications of Nanotechnology, Bren School of Environmental Science and Management, University of California, Santa Barbara, CA 93106 (United States); Keller, Arturo A., E-mail: keller@bren.ucsb.edu [University of California Center for Environmental Implications of Nanotechnology, Bren School of Environmental Science and Management, University of California, Santa Barbara, CA 93106 (United States)

    2012-07-30

    Highlights: Black-Right-Pointing-Pointer Suspension-feeding by mussels can greatly alter mobility and fate of metal oxide nanoparticles. Black-Right-Pointing-Pointer Bioprocessing of metal oxide nanoparticles by mussels removes large fraction from water column. Black-Right-Pointing-Pointer Mussels repackage metal oxide nanoparticles in highly concentrated pseudofeces. Black-Right-Pointing-Pointer Novel biological pathway between major compartments in marine systems. Black-Right-Pointing-Pointer Very different outcome for ZnO and CeO{sub 2} nanoparticles based on their solubility. - Abstract: A growing body of evidence indicates that some engineered nanoparticles (ENPs) are toxic to organisms that perform important ecosystem services in terrestrial and aquatic ecosystems. However, toxicity can be influenced by the biotransformation of contaminants, including ENPs, as it may alter the fate and transport of these substances. In turn, fate and transport can influence their bioavailability. To understand how biotransformation influences the fate and transport of ENPs in marine ecosystems, we exposed suspension-feeding mussels, Mytilus galloprovincialis, to two common nano-metal oxides, CeO{sub 2} and ZnO, over a range of concentrations from 1 mg L{sup -1} to 10 mg L{sup -1}, in a laboratory experiment. Mussels exposed to 10 mg L{sup -1} accumulated 62 {mu}g g{sup -1} of Ce and 880 {mu}g g{sup -1} of Zn on a dry tissue basis but rejected 21,000 {mu}g g{sup -1} for Ce and 63,000 {mu}g g{sup -1} for Zn in pseudofeces. Scanning electron microscope evidence indicates CeO{sub 2} remained as ENPs but ZnO did not after being rejected by the mussels. Mussels filtered most of the CeO{sub 2} from the aqueous media, while a significant fraction of Zn remained in solution. Differences in ENP solubility affect ENP uptake, excretion, and accumulation in mussels. Our study highlights the potential role of marine suspension feeders in biotransformation of ENPs.

  16. Lake Bacterial Assemblage Composition Is Sensitive to Biological Disturbance Caused by an Invasive Filter Feeder.

    Science.gov (United States)

    Denef, Vincent J; Carrick, Hunter J; Cavaletto, Joann; Chiang, Edna; Johengen, Thomas H; Vanderploeg, Henry A

    2017-01-01

    One approach to improve forecasts of how global change will affect ecosystem processes is to better understand how anthropogenic disturbances alter bacterial assemblages that drive biogeochemical cycles. Species invasions are important contributors to global change, but their impacts on bacterial community ecology are rarely investigated. Here, we studied direct impacts of invasive dreissenid mussels (IDMs), one of many invasive filter feeders, on freshwater lake bacterioplankton. We demonstrated that direct effects of IDMs reduced bacterial abundance and altered assemblage composition by preferentially removing larger and particle-associated bacteria. While this increased the relative abundances of many free-living bacterial taxa, some were susceptible to filter feeding, in line with efficient removal of phytoplankton cells of <2 μm. This selective removal of particle-associated and larger bacteria by IDMs altered inferred bacterial functional group representation, defined by carbon and energy source utilization. Specifically, we inferred an increased relative abundance of chemoorganoheterotrophs predicted to be capable of rhodopsin-dependent energy generation. In contrast to the few previous studies that have focused on the longer-term combined direct and indirect effects of IDMs on bacterioplankton, our study showed that IDMs act directly as a biological disturbance to which freshwater bacterial assemblages are sensitive. The negative impacts on particle-associated bacteria, which have been shown to be more active than free-living bacteria, and the inferred shifts in functional group representation raise the possibility that IDMs may directly alter bacterially mediated ecosystem functions. IMPORTANCE Freshwater bacteria play fundamental roles in global elemental cycling and are an intrinsic part of local food webs. Human activities are altering freshwater environments, and much has been learned regarding the sensitivity of bacterial assemblages to a variety of

  17. A new hybrid evolutionary algorithm based on new fuzzy adaptive PSO and NM algorithms for Distribution Feeder Reconfiguration

    International Nuclear Information System (INIS)

    Niknam, Taher; Azadfarsani, Ehsan; Jabbari, Masoud

    2012-01-01

    Highlights: ► Network reconfiguration is a very important way to save the electrical energy. ► This paper proposes a new algorithm to solve the DFR. ► The algorithm combines NFAPSO with NM. ► The proposed algorithm is tested on two distribution test feeders. - Abstract: Network reconfiguration for loss reduction in distribution system is a very important way to save the electrical energy. This paper proposes a new hybrid evolutionary algorithm to solve the Distribution Feeder Reconfiguration problem (DFR). The algorithm is based on combination of a New Fuzzy Adaptive Particle Swarm Optimization (NFAPSO) and Nelder–Mead simplex search method (NM) called NFAPSO–NM. In the proposed algorithm, a new fuzzy adaptive particle swarm optimization includes two parts. The first part is Fuzzy Adaptive Binary Particle Swarm Optimization (FABPSO) that determines the status of tie switches (open or close) and second part is Fuzzy Adaptive Discrete Particle Swarm Optimization (FADPSO) that determines the sectionalizing switch number. In other side, due to the results of binary PSO(BPSO) and discrete PSO(DPSO) algorithms highly depends on the values of their parameters such as the inertia weight and learning factors, a fuzzy system is employed to adaptively adjust the parameters during the search process. Moreover, the Nelder–Mead simplex search method is combined with the NFAPSO algorithm to improve its performance. Finally, the proposed algorithm is tested on two distribution test feeders. The results of simulation show that the proposed method is very powerful and guarantees to obtain the global optimization.

  18. Index-Based Assessment of Voltage Rise and Reverse Power Flow Phenomena in a Distribution Feeder Under High PV Penetration

    DEFF Research Database (Denmark)

    Hasheminamin, Maryam; Agelidis, Vassilios G.; Salehi, Vahid

    2015-01-01

    -based methodology for assessing the impact of high solar PV generation, considering the reverse power flow and voltage rise phenomena. Indices are defined that link these two phenomena and their impact on the voltage profile across the feeder. This assessment relies on detailed modeling of the network and the solar......The proliferation of photovoltaic (PV) generation in low- and medium-voltage distribution networks is expected to continue. Qualified studies can quantify adverse impacts of high PV penetration on distribution networks and assist utilities in decision making. This paper proposes an index...

  19. Overview of improvements in work practices and instrumentation for CANDU primary heat transport feeders in-service inspections

    Energy Technology Data Exchange (ETDEWEB)

    Marcotte, O., E-mail: olivier@nucleom.ca [Nucleom Inc., Quebec, Quebec (Canada); Rousseau, G., E-mail: rousseau.gilles.a@hydro.qc.ca [Hydro Quebec, Becancour, Quebec (Canada); Rochefort, E., E-mail: erochfort@zetec.com [Zetec Canada, Quebec, Quebec (Canada)

    2013-01-15

    The Canadian nuclear industry has developed many advanced non-destructive inspection techniques to be applied safely in hazardous environments in recent years. Automated systems, manual tooling and specialized software modules have been designed since early 2000s to provide complete and very efficient fitness for service inspection of primary heat transport system carbon steel feeder pipes. These techniques deal with complex geometries, difficult access and, radioactive environment. Complementary NDE techniques, namely Ultrasounds, eddy current, phased-array UT and automated scanners are used. This presentation describes the improvements in inspection practices and the advanced data analysis features. (author)

  20. Immunoflourescence and mRNA analysis of human embryonic stem cells (hESCs) grown under feeder-free conditions

    DEFF Research Database (Denmark)

    Awan, Aashir; Oliveri, Roberto S; Jensen, Pernille L

    2010-01-01

    onto 16-well glass chambers, and continuing with the general IF and qPCR steps will be provided. The techniques will be illustrated with new results on cellular localization of transcriptional factors and components of the Hedgehog, Wnt, and PDGF signaling pathways to primary cilia in stem cell......This chapter describes the procedures in order to do immunofluorescence (IF) microscopy and quantitative PCR (qPCR) analysis of human embryonic stem cells (hESCs) grown specifically under feeder-free conditions. A detailed protocol outlining the steps from initially growing the cells, passaging...

  1. Implementation of the resonant vibratory feeders control algorithm on Simatic S7-1200 from MATLAB Simulink enviroment

    Directory of Open Access Journals (Sweden)

    Mitrović Radomir B.

    2016-01-01

    Full Text Available Simulink is an important tool for modeling and simulation of process and control algorithms. It's expansion, PLC Coder, enables direct conversion of model subsystem into SCL, structured text code, which is then used by PLC IDE to create function blocks. This shortens developing time of algorithms for PLC controller. Also, this reduces possibility for a coding error. This paper describes Simulink PLC Coder and workflow for developing PID control algorithm for Siemens Simatic S7-1200 PLC. Control object used here is resonant vibratory feeder having electromagnetic drive.

  2. Using Human Gestures and Generic Skills to Instruct a Mobile Robot Arm in a Feeder Filling Scenario

    DEFF Research Database (Denmark)

    Pedersen, Mikkel Rath; Høilund, Carsten; Krüger, Volker

    2012-01-01

    Mobile robots that have the ability to cooperate with humans are able to provide new possibilities to manufac- turing industries. In this paper, we discuss our mobile robot arm that a) can provide assistance at different locations in a factory and b) that can be programmed using complex human...... actions such as pointing in Take this object. In this paper, we discuss the use of the mobile robot for a feeding scenario where a human operator specifies the parts and the feeders through pointing gestures. The system is partially built using generic robotic skills. Through extensive experiments, we...

  3. EXPERIENCE OF USING A NON-SELECTIVE BETA-BLOCKER IN COMPLEX THERAPY OF REPOLARIZATION DISORDERS IN YOUNG ATHLETES

    Directory of Open Access Journals (Sweden)

    A. Yu. Tikhomirov

    2017-01-01

    Full Text Available Purpose. To study the effectiveness of various schemes of correction of repolarization disorder syndrome, including with the use of beta-blockers, in young athletes of the initial training group.Materials and methods. At the first stage, 410 children involved in sports sections were examined. The average age of the examined was 12.22 ± 3.11 years. At the second stage, the athletes (boys of the initial training group were selected from the surveyed contingent, engaged in martial arts. The groups were formed: A – people with violation of myocardial repolarization processes (72 patients, the average age 10,50 ± 0,35 years, the control group – people without changes in an electrocardiogram (33 people, the average age 10.36 ± 0, 62 years old. All underwent an electrocardiographic study at rest and after physical activity on the Innomed HS80GL apparatus with analysis of the main indicators. The vegetative status and the state of adaptation were estimated by Kerdo index and adaptive potential by Baevsky. After the examination, the subgroup A1 (40 people was prescribed metabolic and antioxidant drugs. Additionally, in the subgroup A2 (32 people, a non-selective beta-blocker was included in the treatment regimen. The course of treatment is 10 days. The analysis of indicators was carried out in 10 days and in a month after the initiation treatment. Statistical processing was carried out in the program Statistica.Results. An earlier disappearance of cardialgia was determined in the subgroup A2 (p < 0.05, whereas in the subgroup A1, 5% of patients had complaints not only at the end of the course, but also a month later after the initiation treatment. The more rapid positive dynamics of the electrocardiographic pattern with a more stable result was observed with the prescription of a beta-blocker.Conclusion. It was proved the advisability of prescribing of beta-blockers in the treatment of beginning athletes with violation of myocardial repolarization

  4. Introducing tool-based feeders to zoo-housed chimpanzees as a cognitive challenge: spontaneous acquisition of new types of tool use and effects on behaviours and use of space.

    OpenAIRE

    Yamanashi, Yumi; Matsunaga, Masayuki; Shimada, Kanae; Kado, Ryuichiro; Tanaka, Masayuki

    2016-01-01

    Cognitively challenging environments are vital to the welfare of captive animals. However, practical enrichment devices that can facilitate animals’ natural behaviours and accommodate individual variation are still limited. We created two types of feeders to facilitate tool-using behaviour in captive chimpanzees: pounding and dipping feeders. The pounding feeder was inspired by pestle-pounding behaviour observed in wild chimpanzees, and we expected that chimpanzees would pound soft foods. The...

  5. Testing the FOODBANCS hypothesis: Seasonal variations in near-bottom particle flux, bioturbation intensity, and deposit feeding based on 234Th measurements

    Science.gov (United States)

    McClintic, Mark A.; DeMaster, David J.; Thomas, Carrie J.; Smith, Craig R.

    2008-11-01

    Naturally occurring 234Th (24-d half-life) was used on the West Antarctic continental shelf to evaluate temporal variations in the flux of particulate material reaching the seabed, bioturbation intensity, the seasonal continuity of feeding by benthic fauna, and trends in particle selection during ingestion for six common detritivores (four surface deposit feeders and two subsurface deposit feeders). These measurements were made at three stations during the five FOODBANCS cruises (December 1999, March, June, and October 2000, and March 2001) to assess the nature of pelagic-benthic coupling on the shelf and to evaluate the seabed as a potential food bank for deposit feeders when surface primary production is minimal. Two summer regimes were sampled (March 2000 and March 2001) with the latter exhibiting a distinct 1-2-cm-thick phytodetritus layer in nearly all sediment core samples. At site B, the 234Th fluxes into the near-bottom (150/170 mab) sediment traps were indistinguishable for the December-March 2000, March-June 2000, and June-October 2000 sampling intervals (fluxes ranging from 170 to 280 dpm m -2 d -1). However, the sediment-trap 234Th flux measured for the October 2000-March 2001 interval (1000 dpm m -2 d -1) was ˜5-fold greater than during the other three sampling periods, consistent with the deposition of a phytodetritus layer. The steady-state 234Th fluxes derived from seabed inventories at site B were 2.4-2.7 times greater than the sediment-trap 234Th fluxes, indicating substantial scavenging of this particle-reactive radiotracer in the bottom 150 m of the water column and/or lateral transport near the seabed. The seabed 234Th inventories at the three stations showed no variation during the first four cruises, but were significantly greater during cruise FB-V (March 2001), when the phytodetritus layer occurred. Based on 234Th distributions in the seabed, bioturbation intensities (quantified using the diffusive mixing coefficient, Db) varied from 0

  6. Evaluation of the effect of radiation levels and dose rates in irradiation of murine fibroblasts used as a feeder layer in the culture of human keratinocytes

    International Nuclear Information System (INIS)

    Yoshito, Daniele; Almeida, Tiago L.; Santin, Stefany Plumeri; Somessari, Elizabeth S.R.; Silveira, Carlos G. da; Mathor, Monica B.; Altran, Silvana C.; Isaac, Cesar

    2009-01-01

    In 1975, Rheinwald and Green published an effective methodology for obtaining and cultivating human keratinocytes. This methodology consisted of seeding keratinocytes onto a feeder layer composed of lineage 3T3 murine fibroblasts, the proliferation rate of which is then controlled through the action of ionizing radiation. The presence of the feeder layer encourages the development of keratinocyte colonies and their propagation in similar cultures, becoming possible several clinical applications as skin substitutes or wound dressings in situations such as post burn extensive skin loss and other skin disorders. However, good development of these keratinocytes depends on a high quality feeder layer among other factors. In the present work, we evaluated the relationship between radiation levels and dose rates applied to fibroblasts used in construction of feeder layers and the radiation effect on keratinocytes colonies forming efficiency. Results indicate 3T3 lineage murine fibroblasts irradiated with doses varying between 60 and 100 Gy can be used as a feeder layer immediately after irradiation or storage of the irradiated cells in suspension at 4 g C for 24 hours with similar results. The exception is when the irradiation dose rate is 2.75 Gyh -1 ; in this case, results suggested that the fibroblasts should be used immediately after irradiation. (author)

  7. An efficient hybrid evolutionary algorithm based on PSO and HBMO algorithms for multi-objective Distribution Feeder Reconfiguration

    Energy Technology Data Exchange (ETDEWEB)

    Niknam, Taher [Electronic and Electrical Engineering Department, Shiraz University of Technology, Shiraz (Iran)

    2009-08-15

    This paper introduces a robust searching hybrid evolutionary algorithm to solve the multi-objective Distribution Feeder Reconfiguration (DFR). The main objective of the DFR is to minimize the real power loss, deviation of the nodes' voltage, the number of switching operations, and balance the loads on the feeders. Because of the fact that the objectives are different and no commensurable, it is difficult to solve the problem by conventional approaches that may optimize a single objective. This paper presents a new approach based on norm3 for the DFR problem. In the proposed method, the objective functions are considered as a vector and the aim is to maximize the distance (norm2) between the objective function vector and the worst objective function vector while the constraints are met. Since the proposed DFR is a multi objective and non-differentiable optimization problem, a new hybrid evolutionary algorithm (EA) based on the combination of the Honey Bee Mating Optimization (HBMO) and the Discrete Particle Swarm Optimization (DPSO), called DPSO-HBMO, is implied to solve it. The results of the proposed reconfiguration method are compared with the solutions obtained by other approaches, the original DPSO and HBMO over different distribution test systems. (author)

  8. A look at one of the world`s largest apron feeder drives - Alberta Oil Sands Project

    Energy Technology Data Exchange (ETDEWEB)

    Persson, O. [Hagglunds Drives Canada Inc., Vancouver, BC (Canada)

    1999-10-01

    Various types of equipment to transport tar sands to processing plants are discussed, with special attention to the advantages of hydraulic direct drives over conventional electro-mechanical drives. A hydraulic direct drive such as the Hagglund Drive has exceptional starting torque capacity due to the high torque capability of the hydraulic motor. As such, it can be particularly useful in applications where shock loads occur with some frequency, or where many starts and stops are needed. Application of the Hagglund drive to power one of the world`s largest apron feeders in the Alberta Oil Sands is described as an illustration of the exceptional reliability, productivity and performance of this equipment. It has about one five-hundredth of the inertia of an equivalent high speed drive with gear reducer, a feature which is particularly significant in the case of feeders which are known to suffer much downtime due to chain related problems. These types of drives have also been used to great advantage in the process industries like pulp and paper, chemical, rubber and plastics, recycling and steel. 1 tab., 1 fig.

  9. A look at one of the world's largest apron feeder drives - Alberta Oil Sands Project

    Energy Technology Data Exchange (ETDEWEB)

    Persson, O. (Hagglunds Drives Canada Inc., Vancouver, BC (Canada))

    1999-01-01

    Various types of equipment to transport tar sands to processing plants are discussed, with special attention to the advantages of hydraulic direct drives over conventional electro-mechanical drives. A hydraulic direct drive such as the Hagglund Drive has exceptional starting torque capacity due to the high torque capability of the hydraulic motor. As such, it can be particularly useful in applications where shock loads occur with some frequency, or where many starts and stops are needed. Application of the Hagglund drive to power one of the world's largest apron feeders in the Alberta Oil Sands is described as an illustration of the exceptional reliability, productivity and performance of this equipment. It has about one five-hundredth of the inertia of an equivalent high speed drive with gear reducer, a feature which is particularly significant in the case of feeders which are known to suffer much downtime due to chain related problems. These types of drives have also been used to great advantage in the process industries like pulp and paper, chemical, rubber and plastics, recycling and steel. 1 tab., 1 fig.

  10. A feeder-free, human plasma-derived hydrogel for maintenance of a human embryonic stem cell phenotype in vitro

    Directory of Open Access Journals (Sweden)

    Lewis Fiona C

    2012-08-01

    Full Text Available Abstract Background Human embryonic stem cells (hESCs represent a tremendous resource for cell therapies and the study of human development; however to maintain their undifferentiated state in vitro they routinely require the use of mouse embryonic fibroblast (MEF feeder-layers and exogenous protein media supplementation. Results These well established requirements can be overcome and in this study, it will be demonstrated that phenotypic stability of hESCs can be maintained using a novel, human plasma protein-based hydrogel as an extracellular culture matrix without the use of feeder cell co-culture. hESCs were resuspended in human platelet poor plasma (PPP, which was gelled by the addition of calcium containing DMEM-based hESC culture medium. Phenotypic and genomic expression of the pluripotency markers OCT4, NANOG and SOX2 were measured using immunohistochemistry and qRT-PCR respectively. Typical hESC morphology was demonstrated throughout in vitro culture and both viability and phenotypic stability were maintained throughout extended culture, up to 25 passages. Conclusions PPP-derived hydrogel has demonstrated to be an efficacious alternative to MEF co-culture with its hydrophilicity allowing for this substrate to be delivered via minimally invasive procedures in a liquid phase with polymerization ensuing in situ. Together this provides a novel technique for the study of this unique group of stem cells in either 2D or 3D both in vitro and in vivo.

  11. Establishment of rat embryonic stem-like cells from the morula using a combination of feeder layers.

    Science.gov (United States)

    Sano, Chiaki; Matsumoto, Asako; Sato, Eimei; Fukui, Emiko; Yoshizawa, Midori; Matsumoto, Hiromichi

    2009-08-01

    Embryonic stem (ES) cells are characterized by pluripotency, in particular the ability to form a germline on injection into blastocysts. Despite numerous attempts, ES cell lines derived from rat embryos have not yet been established. The reason for this is unclear, although certain intrinsic biological differences among species and/or strains have been reported. Herein, using Wistar-Imamichi rats, specific characteristics of preimplantation embryos are described. At the blastocyst stage, Oct4 (also called Pou5f1) was expressed in both the inner cell mass (ICM) and the trophectoderm (TE), whereas expression of Cdx2 was localized to the TE. In contrast, at an earlier stage, expression of Oct4 was detected in all the nuclei in the morula. These stages were examined using a combination of feeder layers (rat embryonic fibroblast [REF] for primary outgrowth and SIM mouse embryo-derived thioguanine- and ouabain-resistant [STO] cells for passaging) to establish rat ES-like cell lines. The rat ES-like cell lines obtained from the morula maintained expression of Oct4 over long-term culture, whereas cell lines derived from blastocysts lost pluripotency during early passage. The morula-derived ES-like cell lines showed Oct4 expression in a long-term culture, even after cryogenic preservation, thawing and EGFP transfection. These results indicate that rat ES-like cell lines with long-term Oct4 expression can be established from the morula of Wistar-Imamichi rats using a combination of feeder layers.

  12. A Review of Power Distribution Test Feeders in the United States and the Need for Synthetic Representative Networks

    Directory of Open Access Journals (Sweden)

    Fernando E. Postigo Marcos

    2017-11-01

    Full Text Available Under the increasing penetration of distributed energy resources and new smart network technologies, distribution utilities face new challenges and opportunities to ensure reliable operations, manage service quality, and reduce operational and investment costs. Simultaneously, the research community is developing algorithms for advanced controls and distribution automation that can help to address some of these challenges. However, there is a shortage of realistic test systems that are publically available for development, testing, and evaluation of such new algorithms. Concerns around revealing critical infrastructure details and customer privacy have severely limited the number of actual networks published and that are available for testing. In recent decades, several distribution test feeders and US-featured representative networks have been published, but the scale, complexity, and control data vary widely. This paper presents a first-of-a-kind structured literature review of published distribution test networks with a special emphasis on classifying their main characteristics and identifying the types of studies for which they have been used. This both aids researchers in choosing suitable test networks for their needs and highlights the opportunities and directions for further test system development. In particular, we highlight the need for building large-scale synthetic networks to overcome the identified drawbacks of current distribution test feeders.

  13. Short communication: Milk meal pattern of dairy calves is affected by computer-controlled milk feeder set-up

    DEFF Research Database (Denmark)

    Jensen, Margit Bak

    2009-01-01

    for a minimum of 2 and 4 portions, respectively, whereas low-fed calves ingested their milk in 2.4 and 4.4 meals for a minimum of 2 and 4 portions, respectively. Calves on a high milk allowance had fewer milk meals over time, whereas calves on a low milk allowance had the same number of milk meals throughout...... milk portions, whereas the other half could ingest the milk in 4 or more daily portions. Data were collected during 3 successive 14-d periods, the first period starting the day after introduction to the feeder at minimum 12 d of age. High-fed calves ingested their milk in 4.0 and 4.9 meals....... Thus, the development from small and frequent milk meals to fewer and larger meals reported by studies of natural suckling was also found among high-fed calves on a computer-controlled milk feeder. Irrespectively of minimum number of milk portions, the low-fed calves had more unrewarded visits...

  14. Comparative abundance and distribution of major filter-feeders in the Antarctic pelagic zone

    Science.gov (United States)

    Voronina, N. M.

    1998-11-01

    published P/B coefficients. For the copepods its value was taken as 4.4 and for krill as 0.79. The total annual production of copepods was estimated as 2534 10 6 t and that of krill as 215 10 6 t (fresh mass). Salp production could not be evaluated, for lack of a sufficient database. In terms of fresh mass, the main share of filter-feeder biomass on the entire Antarctic scale belongs to salps, due to their local maxima; the second place belongs to copepods and krill comes in the third position. But after recalculation in terms of dry mass, copepods shift to the first place and salps to the last. The annual production of copepods significantly exceeds that of krill.

  15. Infraordinary Deposits

    DEFF Research Database (Denmark)

    2016-01-01

    The exhibition Infraordinary Deposits presents three works in progress by PhD Fellow Espen Lunde Nielsen from the on-going PhD project Architectural Probes of the Infraordinary: Social Coexistence through Everyday Spaces. The infraordinary is understood as the opposite of the extraordinary...... and as that which is ‘worn half-invisible’ by use. Nevertheless, these unregarded spaces play a vital role to the social dimension of the city. The selected projects (‘urban biopsies’) on display explore how people coexist through these spaces and within the city itself, either through events in real......, daily 8.45 – 15.00 Where: Aarhus School of Architecture, The Canteen, Nørreport 18, 8000 Aarhus C...

  16. Chronic Periprosthetic Hip Joint Infection. A Retrospective, Observational Study on the Treatment Strategy and Prognosis in 130 Non-Selected Patients

    DEFF Research Database (Denmark)

    Lange, Jeppe; Troelsen, Anders; Søballe, Kjeld

    2016-01-01

    INTRODUCTION: Limited information is available regarding the treatment strategy and prognosis of non-selected patients treated for chronic periprosthetic hip joint infection. Such information is important as no head-to-head studies on treatment strategies are available. The purpose of this study...... is to report on the treatment strategy and prognosis of a non-selected, consecutive patient population. METHODS: We identified 130 patients in the National Patient Registry, consecutively treated for a chronic periprosthetic hip joint infection between 2003-2008 at 11 departments of orthopaedic surgery. We...... extracted information regarding patient demographics, treatment and outcome. 82 patients were re-implanted in a two-stage revision (national standard), the remaining 48 were not re-implanted in a two-stage revision. We were able to collect up-to-date information on all patients to date of death or medical...

  17. CANDU fuel deposits and chemistry optimizations. Recent regulatory experience in Canadian Nuclear Power Plants

    International Nuclear Information System (INIS)

    Kameswaran, Ram

    2014-01-01

    Water chemistry of the Primary Heat Transport System (PHT) of CANDU – Pressurised Heavy Water Reactors profoundly influences the transport of corrosion products around the Heat Transport System (HTS), where they can be deposited as crud on steam generators, feeder pipes and on the fuel. Fuel cladding can be covered with deposits which have precipitated from the coolant as a result of temperature changes or non-optimal coolant pH. Precipitation of deposits in-core must be avoided as far as possible, as it leads to fouling of the fuel, loss of heat transfer efficiency, and increased radiation fields. In the recent years a Canadian NPP experienced increased instances of black deposits being observed on fuel bundles discharged from one of the units. The black deposits were initially observed in 2008 during in-bay fuel inspections. Since then it has been determined that all the discharged fuel bundles have black deposits on them and that observed deposits have been increasing in size (thickness and surface area). This negative trend has persisted through to 2012, when one of fuel bundles was observed with significantly larger deposit than previously seen. Initial analysis of the deposit indicated it to be iron oxide (magnetite). Flow Accelerated Corrosion (FAC) of carbon steel feeder pipes is the primary source of iron, which deposits as magnetite on HTS surfaces. The black deposits have predominantly been located immediately downstream of the bearing pads of the fuel bundle. Deposits have also tended to form on the bottom-downstream quadrant of the fuel bundles. The deposits were most prevalent in low power channels, but some deposits have been observed on high power channels. It was reported by the utility that the PHT system chemistry has been maintained in specification for most of the time during normal operation but the chemistry control during outages was inadequate. Due to design constraints, purification circuit was not available during outages and ion

  18. The Stingless Bee Melipona solani Deposits a Signature Mixture and Methyl Oleate to Mark Valuable Food Sources.

    Science.gov (United States)

    Alavez-Rosas, David; Malo, Edi A; Guzmán, Miguel A; Sánchez-Guillén, Daniel; Villanueva-Gutiérrez, Rogel; Cruz-López, Leopoldo

    2017-10-01

    Stingless bees foraging for food improve recruitment by depositing chemical cues on valuable food sites or pheromone marks on vegetation. Using gas chromatography/mass spectrometry and bioassays, we showed that Melipona solani foragers leave a mixture composed mostly of long chain hydrocarbons from their abdominal cuticle plus methyl oleate from the labial gland as a scent mark on rich food sites. The composition of hydrocarbons was highly variable among individuals and varied in proportions, depending on the body part. A wide ratio of compounds present in different body parts of the bees elicited electroantennogram responses from foragers and these responses were dose dependent. Generally, in bioassays, these bees prefer to visit previously visited feeders and feeders marked with extracts from any body part of conspecifics. The mean number of visits to a feeder was enhanced when synthetic methyl oleate was added. We propose that this could be a case of multi-source odor marking, in which hydrocarbons, found in large abundance, act as a signature mixture with attraction enhanced through deposition of methyl oleate, which may indicate a rich food source.

  19. Simulasi Dinamika untuk Menentukan Stabilitas Sistem Tenaga Listrik Menggunakan Thyristor Controlled Braking Resistor pada Sistem IEEE 34 Node Test Feeder

    Directory of Open Access Journals (Sweden)

    Andi Taufiq

    2012-09-01

    Full Text Available Terdapat berbagai macam metode untuk meningkatkan stabilitas sistem  tenaga listrik. Salah satunya adalah dengan menggunakan metode pengereman dinamis (dynamic braking. Generator sinkron sebagai distributed generator yang digerakkan oleh mesin diesel. Pada saat terjadi gangguan pada sistem, digunakan sebuah Thyristor Controlled Braking Resistor (TCBR untuk meredam osilasi yang terjadi. Sistem yang hendak dianalisis dinamika dan stabilitasnnya adalah IEEE 34 node test feeder. Dengan sistem ini diilustrasikan karakteristik dan keefektifan TCBR untuk meredam osilasi frekuensi rendah dan mencegah terjadinya ketidakstabilan transien sistem. Dari hasil analisis diperoleh bahwa dengan adanya penambahan TCBR (Thyristor Controlled Braking Resistor maka respon transien sistem akan menjadi lebih baik. Hal ini ditunjukkan dengan adanya penurunan overshoot dan settling timenya. Dengan demikian sistem akan menuju kondisi stabil dengan lebih cepat setelah terjadi gangguan.

  20. Growth factor expression pattern of homologous feeder layer for culturing buffalo embryonic stem cell-like cells.

    Science.gov (United States)

    Sharma, Ruchi; George, Aman; Kamble, Nitin M; Chauhan, Manmohan S; Singla, Suresh; Manik, Radhey S; Palta, Prabhat

    2012-01-01

    The present study examined the expression profile of buffalo fetal fibroblasts (BFF) used as a feeder layer for embryonic stem (ES) cell-like cells. The expression of important growth factors was detected in cells at different passages. Mitomycin-C inactivation increased relative expression levels of ACTIVIN-A, TGF-β1, BMP-4 and GREMLIN but not of fibroblast growth factor-2 (FGF-2). The expression level of ACTIVIN-A, transforming growth factor-β1 (TGF-β1), bone morphogenetic protein-4 (BMP-4) and FGF-2 was similar in buffalo fetal fibroblast (BFF) cultured in stem cell medium (SCM), SCM+1000IU mL(-1) leukemia inhibitory factor (LIF), SCM+5 ngmL(-1) FGF-2 or SCM+LIF+FGF-2 for 24 h whereas GREMLIN expression was higher in FGF-2-supplemented groups. In spent medium, the concentration of ACTIVIN-A was higher in FGF-2-supplemented groups whereas that of TGF-β1 was similar in SCM and LIF+FGF-2, which was higher than when either LIF or FGF-2 was used alone. Following culture of ES cell-like cells on a feeder layer for 24 h, the TGF-β1 concentration was higher with LIF+FGF-2 than with LIF or FGF-2 alone which, in turn, was higher than that in SCM. In the LIF+FGF-2 group, the concentration of TGF-β1 was lower and that of ACTIVIN-A was higher in spent medium at 24 h than at 48 h of culture. These results suggest that BFF produce signalling molecules that may help in self-renewal of buffalo ES cell-like cells.

  1. Development of an extruder-feeder biomass direct liquefaction process. Volume 2, Parts 4--8: Final report

    Energy Technology Data Exchange (ETDEWEB)

    White, D.H.; Wolf, D. [Arizona Univ., Tucson, AZ (United States). Dept. of Chemical Engineering

    1991-10-01

    As an abundant, renewable, domestic energy resource, biomass could help the United States reduce its dependence on imported oil. Biomass is the only renewable energy technology capable of addressing the national need for liquid transportation fuels. Thus, there is an incentive to develop economic conversion processes for converting biomass, including wood, into liquid fuels. Through research sponsored by the US DOE`s Biomass Thermochemical Conversion Program, the University of Arizona has developed a unique biomass direct liquefaction system. The system features a modified single-screw extruder capable of pumping solid slurries containing as high as 60 wt% wood flour in wood oil derived vacuum bottoms at pressures up to 3000 psi. The extruder-feeder has been integrated with a unique reactor by the University to form a system which offers potential for improving high pressure biomass direct liquefaction technology. The extruder-feeder acts simultaneously as both a feed preheater and a pumping device for injecting wood slurries into a high pressure reactor in the biomass liquefaction process. An experimental facility was constructed and following shakedown operations, wood crude oil was produced by mid-1985. By July 1988, a total of 57 experimental continuous biomass liquefaction runs were made using White Birch wood feedstock. Good operability was achieved at slurry feed rates up to 30 lb/hr, reactor pressures from 800 to 3000 psi and temperatures from 350{degree}C to 430{degree}C under conditions covering a range of carbon monoxide feed rates and sodium carbonate catalyst addition. Crude wood oils containing as little as 6--10 wt% residual oxygen were produced. 38 refs., 82 figs., 26 tabs.

  2. Keratinocytes propagated in serum-free, feeder-free culture conditions fail to form stratified epidermis in a reconstituted skin model.

    Directory of Open Access Journals (Sweden)

    Rebecca Lamb

    Full Text Available Primary human epidermal stem cells isolated from skin tissues and subsequently expanded in tissue culture are used for human therapeutic use to reconstitute skin on patients and to generate artificial skin in culture for academic and commercial research. Classically, epidermal cells, known as keratinocytes, required fibroblast feeder support and serum-containing media for serial propagation. In alignment with global efforts to remove potential animal contaminants, many serum-free, feeder-free culture methods have been developed that support derivation and growth of these cells in 2-dimensional culture. Here we show that keratinocytes grown continually in serum-free and feeder-free conditions were unable to form into a stratified, mature epidermis in a skin equivalent model. This is not due to loss of cell potential as keratinocytes propagated in serum-free, feeder-free conditions retain their ability to form stratified epidermis when re-introduced to classic serum-containing media. Extracellular calcium supplementation failed to improve epidermis development. In contrast, the addition of serum to commercial, growth media developed for serum-free expansion of keratinocytes facilitated 3-dimensional stratification in our skin equivalent model. Moreover, the addition of heat-inactivated serum improved the epidermis structure and thickness, suggesting that serum contains factors that both aid and inhibit stratification.

  3. Feeding current characteristics of three morphologically different bivalve suspension feeders, Crassostrea gigas, Mytilus edulis and Cerastoderma edule, in relation to food competition

    NARCIS (Netherlands)

    Troost, K.; Stamhuis, E.J.; van Duren, L.A; Wolff, W.J.

    Introduced Pacific oysters (Crassostrea gigas) have shown rapid expansion in the Oosterschelde estuary, while stocks of native bivalves declined slightly or remained stable. This indicates that they might have an advantage over native bivalve filter feeders. Hence, at the scale of individual

  4. 47 CFR 25.223 - Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS. 25.223 Section 25.223 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Technical Standards § 25...

  5. 47 CFR 25.258 - Sharing between NGSO MSS Feeder links Stations and GSO FSS services in the 29.25-29.5 GHz Bands.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Sharing between NGSO MSS Feeder links Stations and GSO FSS services in the 29.25-29.5 GHz Bands. 25.258 Section 25.258 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Technical Standards § 25...

  6. Network integration modelling of feeder and BRT(bus rapid transit) to reduce the usage of private vehicles in Palembang’s suburban area

    Science.gov (United States)

    Nur'afalia, D.; Afifa, F.; Rubianto, L.; Handayeni, K. D. M. E.

    2018-01-01

    The aim of this research is to determine the optimal feeder network route that integrates with BRT (Bus Rapid Transit). Palembang, a high growing population city with unresolved transportation demand sector. BRT as main public transportation could not fulfill people’s demand in transportation, especially in Alang-Alang Lebar sub-district. As an impact, the usage of private vehicles increases along the movement toward the city center. The concept of Network Integration that integrates feeder network with BRT is expected to be a solution to suppress the rate of private vehicles’ usage and to improve public transportation service, so that the use of BRT will be increased in the suburban area of Palembang. The method used to identifying the optimal route using Route Analysis method is route analysis using Tranetsim 0.4. The best route is obtained based on 156 movement samples. The result is 58,7% from 199 mobility’s potency of private vehicle usage’s can be reduced if there is a feeder network’s route in Alang-Alang Lebar’s sub-district. From the result, the existance of integration between feeder network and BRT is potential enough to reduce the usage of private vehicles and supports the sustainability of transportation mobility in Palembang City.

  7. Cultivation and irradiation of human fibroblasts in a medium enriched with platelet lysate for obtaining feeder layer in epidermal cell culture

    International Nuclear Information System (INIS)

    Yoshito, Daniele

    2011-01-01

    For over 30 years, the use of culture medium, enriched with bovine serum, and murines fibroblasts, with the rate of proliferation controlled by irradiation or by share anticarcinogenic drugs, has been playing successfully its role in assisting in the development of keratinocytes in culture, for clinical purposes. However, currently there is a growing concern about the possibility of transmitting prions and animals viruses to transplanted patients. Taking into account this concern, the present work aims to cultivate human fibroblasts in a medium enriched with human platelets lysate and determine the irradiation dose of these cells, for obtaining feeder layer in epidermal cell culture. For carrying out the proposed objective, platelets lysis has standardized, this lysate was used for human fibroblasts cultivation and the irradiation dose enough to inhibit its duplication was evaluated. Human keratinocytes were cultivated in these feeder layers, in culture medium enriched with the lysate. With these results we conclude that the 10% platelets lysate promoted a better adhesion and proliferation of human fibroblasts and in all dose levels tested (60 to 300 Gy), these had their mitotic activity inactivated by ionizing irradiation, being that the feeder layers obtained with doses from 70 to 150 Gy were those that provided the best development of keratinocytes in medium containing 2.5% of human platelet lysate. Therefore, it was possible to standardize both the cultivation of human fibroblasts as its inactivation for use as feeder layer in culture of keratinocytes, so as to eliminate xenobiotics components. (author)

  8. Feeding current characteristics of three morphologically different bivalve suspension feeders, Crassostrea gigas Mytilus edulis and Cerastoderma edule , in relation to food competition

    NARCIS (Netherlands)

    Troost, K.; Stamhuis, E.J.; Duren, L.A.; Wolff, W.

    2009-01-01

    Introduced Pacific oysters (Crassostrea gigas) have shown rapid expansion in the Oosterschelde estuary, while stocks of native bivalves declined slightly or remained stable. This indicates that they might have an advantage over native bivalve filter feeders. Hence, at the scale of individual

  9. Effect of stall design on dairy calf transition to voluntary feeding on an automatic milk feeder after introduction to group housing.

    Science.gov (United States)

    Wilson, Tanya R; LeBlanc, Stephen J; DeVries, Trevor J; Haley, Derek B

    2018-06-01

    Automatic milk feeders (AMF) for young dairy calves are widely used in the dairy industry. These feeders are thought to have benefits for calf health and welfare and may reduce labor required for feeding; however, little is known about how calves adapt to feeding with AMF. The objective of this study was to observe the effects of feeding stall design on calves learning to use the AMF. The hypothesis was that solid side stalls, compared with steel bar stalls, would result in a longer latency to approach and feed from the AMF without assistance. A total of 147 Holstein calves (80 male and 67 female) were enrolled at 4 d of age, introduced to a group pen, and, at the same time, trained on an AMF. For training, calves were allowed to suck on the trainer's fingers and guided to the teat. Calves were allocated to 1 of 2 stall designs at the pen level, depending on which treatment cohort they were born into, either with steel bar stall walls (n = 46 male, 34 female calves) or with solid side stall walls (n = 34 male, 33 female calves). For 72 h after introductory training on the AMF, data from the feeders were collected and calf behavior was monitored by video. Outcomes measured included latency to first voluntary visit to the feeder and to first feeding, time spent in the feeder, amount of milk consumed over 72 h, number of retraining sessions required (retrained if linear regression models or a Poisson model for the outcome of retraining. For certain outcomes the effects of stall design interacted with difficulty of training (willingness to enter feeder and drink); for the 38% of calves that were scored as moderately difficult to train on a scale of easy, moderate, or difficult, treatment (stall design) differences were detected. These calves took 2× longer to lick or bite toward the nipple, 2× longer to first voluntarily feeding, and consumed less milk over 72 h following training when trained on the steel bar stall design. These results suggest simple features of a

  10. Measurements of local mass transfer coefficient of Flow Accelerated Corrosion at feeder outlet pipes in CANDU using Plaster of Paris method

    International Nuclear Information System (INIS)

    Hyuk Kwon; Dong Un Seo; Goon-Cherl Park

    2005-01-01

    Full text of publication follows: Flow Accelerated Corrosion (FAC) is a corrosion mechanism that results in wall thinning in piping systems and components. FAC on carbon steels in pure water has occurred in a number of industry and power plant. A pipe wall thinning due to the FAC at nuclear power plant is just reported in confined to carbon steel pipe on the secondary system which does not equip a radioactive component. Recently, at Canadian Deuterium Uranium type reactor, it is reported that the feeder lines suffer the wall thinning on the primary system to equip 380 feeder pipes. Differently from the fast FAC rate of the secondary system on PWR, FAC rate of feeder pipes on CANDU is not more than the 0.2 mm/year. Although the FAC rate of feeder pipe is relatively slow, the narrow thickness margin of 2.6089 mm is endangered sufficiently by only the slow FAC rate. The FAC is governed by the mass transfer coefficient which is determined by the flow field. To well predict the FAC rate, mass transfer coefficient should be well measured or calculated. New measurement method of mass transfer coefficient is developed to obtain the coefficient for the complex shape like feeder pipe. The method evaluated the naphthalene sublimation method to apply it under the water flow. The naphthalene sublimation method can be used to study mass and heat transfer with confidence for a variety of applications, but with certain restrictions. At present, Plaster of paris method can modified the sublimation method to overcome the restrictions. This method is particularly useful in complex flows on geometries and for flows with large gradients in wall transport rate. The test specimen can be easily prepared by several methods, including dipping, machining, spraying, and casting. The local transfer coefficients can be determined with high accuracy and in detail by automated measurement systems that eliminate most human errors during the measurement process. To evaluate the method, the

  11. Flow visualization study of two phase flow in a single bend outlet feeder pipe and horizontal annulus of outlet end-fitting of a CANDU reactor

    International Nuclear Information System (INIS)

    Supa-Amornkul, S.; Lister, D.H.; Steward, F.R.

    2005-01-01

    'Full text:' In CANDU-6 reactors, the pressurized high-temperature coolant flows through 380 fuel channels passing horizontally through the core. Each end of a fuel channel has a stainless steel annular end-fitting connected to a carbon steel feeder pipe. The outlet coolant, which is at 310 o C with up to 0.30 steam voidage, turns through 90 o as it passes from flow in the annular end-fitting to pipe flow in the feeder via a Grayloc connector. Since 1996, several CANDU stations have reported excessive corrosion of their outlet feeder pipes; especially between the first metre, which consisted of single or double bends. Early studies related the attack to the hydrodynamics of the coolant and verified that it was a type of flow accelerated corrosion. In order to understand the hydrodynamics of the coolant in the outlet feeders by flow-visualization, a full-scale transparent test section simulating the geometry and orientation of an outlet feeder bend with its upstream annular end-fitting were fabricated. The feeder consisted of a 54 mm inside diameter acrylic pipe with a 73 o bend, connecting to an acrylic simulation of a Grayloc flanged fitting and annular end-fitting. The annular end-fitting consisted of an inner pipe, 110 mm outer diameter, and an outer pipe, 150 mm inner diameter, both 190.7 cm long in length. The tests were performed with water and air at atmospheric pressure and room temperature. The maximum water volumetric flow rate was 19 L/s and the volume fraction of air varied from 0.05 to 0.56. The phase distributions within the feeder pipe and along the length of the annulus were investigated with a digital video recorder. Size, concentration and velocity of the air bubbles at particular locations were studied with a high-speed digital still camera and a high-speed digital video camera. Phase distributions and variations in bubble size with velocity were determined. Particular attention was paid to the flow pattern at the inside of the bend, where a CFD

  12. Flow visualization study of two phase flow in a single bend outlet feeder pipe and horizontal annulus of outlet end-fitting of a CANDU reactor

    Energy Technology Data Exchange (ETDEWEB)

    Supa-Amornkul, S.; Lister, D.H.; Steward, F.R. [Univ. of New Brunswick, Fredericton, New Brunswick (Canada)]. E-mail: h796e@unb.ca; dlister@unb.ca; fsteward@unb.ca

    2005-07-01

    'Full text:' In CANDU-6 reactors, the pressurized high-temperature coolant flows through 380 fuel channels passing horizontally through the core. Each end of a fuel channel has a stainless steel annular end-fitting connected to a carbon steel feeder pipe. The outlet coolant, which is at 310{sup o}C with up to 0.30 steam voidage, turns through 90{sup o} as it passes from flow in the annular end-fitting to pipe flow in the feeder via a Grayloc connector. Since 1996, several CANDU stations have reported excessive corrosion of their outlet feeder pipes; especially between the first metre, which consisted of single or double bends. Early studies related the attack to the hydrodynamics of the coolant and verified that it was a type of flow accelerated corrosion. In order to understand the hydrodynamics of the coolant in the outlet feeders by flow-visualization, a full-scale transparent test section simulating the geometry and orientation of an outlet feeder bend with its upstream annular end-fitting were fabricated. The feeder consisted of a 54 mm inside diameter acrylic pipe with a 73{sup o} bend, connecting to an acrylic simulation of a Grayloc flanged fitting and annular end-fitting. The annular end-fitting consisted of an inner pipe, 110 mm outer diameter, and an outer pipe, 150 mm inner diameter, both 190.7 cm long in length. The tests were performed with water and air at atmospheric pressure and room temperature. The maximum water volumetric flow rate was 19 L/s and the volume fraction of air varied from 0.05 to 0.56. The phase distributions within the feeder pipe and along the length of the annulus were investigated with a digital video recorder. Size, concentration and velocity of the air bubbles at particular locations were studied with a high-speed digital still camera and a high-speed digital video camera. Phase distributions and variations in bubble size with velocity were determined. Particular attention was paid to the flow pattern at the inside

  13. Effect of feeder space during the growing and laying periods and the rate of feed increase at the onset of lay on broiler breeder female reproductive function.

    Science.gov (United States)

    Leksrisompong, N; Romero-Sanchez, H; Oviedo-Rondón, E O; Brake, J

    2014-07-01

    A study was conducted to examine how 2 feeder space allocations during the rearing period followed by 2 feeder space allocations after photostimulation and 2 female feeding to peak programs (fast or slow) affected female broiler breeder reproductive performance and mortality. Sixteen pens of 76 breeder females each were equipped with either 4 tube feeders with a 132 cm circumference pan (7.0 cm/female) or 6 feeders (10.4 cm/female) to 21 wk of age. Thereafter, 64 females were moved to breeding pens, photostimulated, and fed sex-separate from either 3 (6.2 cm/female) or 5 (10.3 cm/female) feeders with either fast or slow feeding to peak feeding programs applied to complete a 2 × 2 × 2 factorial design. Seven males that were separately reared in a similar manner were added per pen. Individual female BW was determined at 6, 20, and 32 wk of age and BW uniformity assessed. Greater feeder space during rearing increased BW at 32 wk of age, whereas greater feeder space during lay or slow feeding to peak decreased BW at 32 wk. There were no differences in BW uniformity. Hens from the 10.4 to 10.3 cm/female combination produced a significantly greater number of eggs as compared with the 7.0 to 10.3 cm/female and 10.4 to 6.2 cm/female combinations with the 7.0 to 6.2 cm/female combination intermediate. Percentage hen-day egg production of the 10.4 to 10.3 cm/female combination hens was significantly greater than all other combinations. Livability was improved in the 10.4 to 10.3 cm/female combination relative to the 7.0 to 10.3 cm/female combination with the others intermediate. The fast feeding to peak program increased yolk weight as well as yolk:albumen ratio at 28 and 30 wk of age, but egg weight did not differ. These data indicated that increased or decreased feeder space between the growing and laying periods did not affect broiler breeder female BW, uniformity, egg weight, fertility, or hatchability. The 10.3 cm/female laying feeder space exhibited the best hen

  14. The effect of a hay grid feeder on feed consumption and measurement of the gastric pH using an intragastric electrode device in horses: a preliminary report.

    Science.gov (United States)

    Aristizabal, F; Nieto, J; Yamout, S; Snyder, J

    2014-07-01

    Obesity and gastric ulceration are highly prevalent in horses. Management modifications for preventing squamous gastric ulceration include frequent feeding and free access to pasture; however, these practices may predispose horses to obesity. To compare the percentage of hay consumed, intragastric pH and horse activity between feeding from the ground and a hay grid feeder. Crossover experimental study. A pH electrode was inserted into the stomach to record the intragastric pH for 48 h. Horses received 1% of their body weight in grass hay twice a day. Horses were assigned to be fed from the ground or a commercial hay grid feeder for 24 h and then switched to the opposite protocol for an additional 24 h. Horses were continuously video-recorded and the percentage of time spent eating or drinking, walking or standing, and lying down were calculated. Two point data were compared by paired t test and pH over time was compared by repeated measures ANOVA. Horses consumed significantly greater amounts of grass hay when fed on the ground compared with a hay grid feeder (n = 9; PpH values (n = 6; P = 0.97), mean intragastric pH over time (n = 6; P = 0.45) the length of time the pH was below 4.0 (n = 6; P = 0.54), and the percentage of time horses spent eating or drinking (n = 9; P = 0.52), walking or standing (n = 9; P = 0.3), or lying down (n = 9; P = 0.4). Within each group horses spent more time eating during the day compared with the night (n = 9; hay grid feeder P = 0.003; ground feeding P = 0.007). The hay grid feeder studied may be used to reduce the amount of hay ingested by horses without reducing the time horses spend eating. © 2013 EVJ Ltd.

  15. Assessment of Fuel Analysis Methodology and Fission Product Release for 37-Element Fuel by Using the Latest IST Codes during Stagnation Feeder Break in CANDU

    International Nuclear Information System (INIS)

    Park, Joo Hwan; Jung, Jong Yeob

    2009-09-01

    Feeder break accident is regarded as one of the design basis accident in CANDU reactor which results in a fuel failure. For a particular range of inlet feeder break sizes, the flow in the channel is reduced sufficiently that the fuel and fuel channel integrity can be significantly affected to have damage in the affected channel, while the remainder of the core remains adequately cooled. The flow in the downstream channel can be more or less stagnated due to a balance between pressure at the break on the upstream side and the reverse driving pressure between the break and the downstream end. In the extreme, this can lead to rapid fuel heatup and fuel damage and failure of the fuel channel similar to that associated with a severe channel flow blockage. Such an inlet feeder break scenario is called a stagnation break. In this report, the fuel analysis methodology and the assessment results of fission product inventory and release during the stagnation feeder break are described for conservatively assumed limiting channel. The accident was assumed to be occurred in the refurbished Wolsong unit 1 and the latest safety codes were used in the analysis. Fission product inventories during the steady state were calculated by using ELESTRES-IST 1.2 code. The whole analysis process was carried out by a script file which was programmed by Perl language. The perl script file was programmed to make all ELESTRES input files for each bundle and each ring based on the given power-burnup history and thermal-hydraulic conditions of the limiting channel and to perform the fuel analysis automatically. The fission product release during the transient period of stagnation feeder break was evaluated by applying Gehl model. The amounts of each isotope's release are conservatively evaluated for additional 2 seconds after channel failure. The calculated fission product releases are provided to the following dose assessment as a source term

  16. Characterisation of PDO olive oil Chianti Classico by non-selective (UV–visible, NIR and MIR spectroscopy) and selective (fatty acid composition) analytical techniques

    International Nuclear Information System (INIS)

    Casale, M.; Oliveri, P.; Casolino, C.; Sinelli, N.; Zunin, P.; Armanino, C.; Forina, M.; Lanteri, S.

    2012-01-01

    Highlights: ► Characterisation of the Italian PDO extra virgin olive oil Chianti Classico. ► Comparison between non-selective (UV–vis, NIR and MIR spectroscopy) and selective (fatty acid composition) analytical techniques. ► Synergy among spectroscopic techniques, by the fusion of the respective spectra. ► Prediction of the content of oleic and linoleic acids in the olive oils. - Abstract: An authentication study of the Italian PDO (protected designation of origin) extra virgin olive oil Chianti Classico was performed; UV–visible (UV–vis), Near-Infrared (NIR) and Mid-Infrared (MIR) spectroscopies were applied to a set of samples representative of the whole Chianti Classico production area. The non-selective signals (fingerprints) provided by the three spectroscopic techniques were utilised both individually and jointly, after fusion of the respective profile vectors, in order to build a model for the Chianti Classico PDO olive oil. Moreover, these results were compared with those obtained by the gas chromatographic determination of the fatty acids composition. In order to characterise the olive oils produced in the Chianti Classico PDO area, UNEQ (unequal class models) and SIMCA (soft independent modelling of class analogy) were employed both on the MIR, NIR and UV–vis spectra, individually and jointly, and on the fatty acid composition. Finally, PLS (partial least square) regression was applied on the UV–vis, NIR and MIR spectra, in order to predict the content of oleic and linoleic acids in the extra virgin olive oils. UNEQ, SIMCA and PLS were performed after selection of the relevant predictors, in order to increase the efficiency of both classification and regression models. The non-selective information obtained from UV–vis, NIR and MIR spectroscopy allowed to build reliable models for checking the authenticity of the Italian PDO extra virgin olive oil Chianti Classico.

  17. Characterisation of PDO olive oil Chianti Classico by non-selective (UV-visible, NIR and MIR spectroscopy) and selective (fatty acid composition) analytical techniques

    Energy Technology Data Exchange (ETDEWEB)

    Casale, M., E-mail: monica@dictfa.unige.it [Universita degli Studi di Genova, Department of Chemistry and Food and Pharmaceutical Technologies, Via Brigata Salerno 13, I-16147, Genoa (Italy); Oliveri, P.; Casolino, C. [Universita degli Studi di Genova, Department of Chemistry and Food and Pharmaceutical Technologies, Via Brigata Salerno 13, I-16147, Genoa (Italy); Sinelli, N. [Universita degli Studi di Milano, Department of Food Science and Technology, Via Celoria, 2 - I-20133 Milan (Italy); Zunin, P.; Armanino, C.; Forina, M.; Lanteri, S. [Universita degli Studi di Genova, Department of Chemistry and Food and Pharmaceutical Technologies, Via Brigata Salerno 13, I-16147, Genoa (Italy)

    2012-01-27

    Highlights: Black-Right-Pointing-Pointer Characterisation of the Italian PDO extra virgin olive oil Chianti Classico. Black-Right-Pointing-Pointer Comparison between non-selective (UV-vis, NIR and MIR spectroscopy) and selective (fatty acid composition) analytical techniques. Black-Right-Pointing-Pointer Synergy among spectroscopic techniques, by the fusion of the respective spectra. Black-Right-Pointing-Pointer Prediction of the content of oleic and linoleic acids in the olive oils. - Abstract: An authentication study of the Italian PDO (protected designation of origin) extra virgin olive oil Chianti Classico was performed; UV-visible (UV-vis), Near-Infrared (NIR) and Mid-Infrared (MIR) spectroscopies were applied to a set of samples representative of the whole Chianti Classico production area. The non-selective signals (fingerprints) provided by the three spectroscopic techniques were utilised both individually and jointly, after fusion of the respective profile vectors, in order to build a model for the Chianti Classico PDO olive oil. Moreover, these results were compared with those obtained by the gas chromatographic determination of the fatty acids composition. In order to characterise the olive oils produced in the Chianti Classico PDO area, UNEQ (unequal class models) and SIMCA (soft independent modelling of class analogy) were employed both on the MIR, NIR and UV-vis spectra, individually and jointly, and on the fatty acid composition. Finally, PLS (partial least square) regression was applied on the UV-vis, NIR and MIR spectra, in order to predict the content of oleic and linoleic acids in the extra virgin olive oils. UNEQ, SIMCA and PLS were performed after selection of the relevant predictors, in order to increase the efficiency of both classification and regression models. The non-selective information obtained from UV-vis, NIR and MIR spectroscopy allowed to build reliable models for checking the authenticity of the Italian PDO extra virgin olive oil

  18. [Cost-effectiveness analysis of celecoxib versus non-selective non-steroidal anti-inflammatory drug therapy for the treatment of osteoarthritis in Spain: A current perspective].

    Science.gov (United States)

    De Lossada, A; Oteo-Álvaro, Á; Giménez, S; Oyagüez, I; Rejas, J

    2016-01-01

    To assess the cost-effectiveness of celecoxib and non-selective non-steroidal anti-inflammatory drugs for the treatment of osteoarthritis in clinical practice in Spain. A decision-tree model using distribution, doses, treatment duration and incidence of GI and CV events observed in the pragmatic PROBE-designed «GI-Reasons» trial was used for cost-effectiveness. Effectiveness was expressed in terms of event averted and quality-adjusted life-years (QALY) gained. QALY were calculated based on utility decrement in case of any adverse events reported in GI-Reasons trial. The National Health System perspective in Spain was applied; cost calculations included current prices of drugs plus cost of adverse events occurred. The analysis was expressed as an incremental cost-effectiveness ratio per QALY gained and per event averted. One-way and probabilistic analyses were performed. Compared with non-selective non-steroidal anti-inflammatory drugs, at current prices, celecoxib treatment had higher overall treatment costs €201 and €157, respectively. However, celecoxib was associated with a slight increase in QALY gain and significantly lower incidence of gastrointestinal events (pcost-effectiveness ratio of €13,286 per QALY gained and €4,471 per event averted. Sensitivity analyses were robust, and confirmed the results of the base case. Celecoxib at current price may be considered as a cost-effective alternative vs. non-selective non-steroidal anti-inflammatory drugs in the treatment of osteoarthritis in daily practice in the Spanish NHS. Copyright © 2015 Sociedad Española de Médicos de Atención Primaria (SEMERGEN). Publicado por Elsevier España, S.L.U. All rights reserved.

  19. Effects, Uptake, and Depuration Kinetics of Silver Oxide and Copper Oxide Nanoparticles in a Marine Deposit Feeder, Macoma balthica

    DEFF Research Database (Denmark)

    Dai, Lina; Syberg, Kristian; Banta, Gary Thomas

    2013-01-01

    for any of the metal forms at measured sediment concentrations (150−200 μg/g) during 35 d of exposure. No genotoxicity was observed following exposure, measured as DNA damage with the single-cell gel electrophoresis assay (comet assay). Bioaccumulation of both Ag and Cu in the clams was form dependent...

  20. Investigation of the role of non-selective calcium channel blocker (flunarizine) on cerebral ischemic-reperfusion associated cognitive dysfunction in aged mice.

    Science.gov (United States)

    Gulati, Puja; Muthuraman, Arunachalam; Kaur, Parneet

    2015-04-01

    The present study was designed to investigate the role of flunarizine (a non-selective calcium channel blocker) on cerebral ischemic-reperfusion associated cognitive dysfunction in aged mice. Bilateral carotid artery occlusion of 12min followed by reperfusion for 24h was given to induce cerebral injury in male Swiss mice. The assessment of learning & memory was performed by Morris water maze test; motor in-coordination was evaluated by rota rod, lateral push and inclined beam walking tests; cerebral infarct size was quantified by triphenyltetrazolium chloride staining. In addition, reduced glutathione (GSH), total calcium and acetylcholinesterase (AChE) activity were also estimated in aged brain tissue. Donepezil treated group served as a positive control in this study. Ischemia reperfusion (I/R) injury produced significant increase in cerebral infarct size. A significant loss of memory along with impairment of motor performance was also noted. Further, I/R injury also produced significant increase in levels of total calcium, AChE activity and decrease in GSH levels. Pretreatment of flunarizine significantly attenuated I/R induced infarct size, behavioral and biochemical changes. Hence, it may be concluded that, a non-selective calcium channel blocker can be useful in I/R associated cognitive dysfunction due to its anti-oxidant, anti-infarct and modulatory actions of neurotransmitters & calcium channels. Copyright © 2015 Elsevier Inc. All rights reserved.

  1. Prevalence of latent and manifest hyperthyroidism in an iodine-deficient area: non-selected patient population admitted for CT studies with iodine-containing contrast agents

    International Nuclear Information System (INIS)

    Saam, T.; Hess, T.; Kasperk, C.; Kauffmann, G.W.; Duex, M.

    2005-01-01

    Purpose: to evaluate the prevalence of latent and manifest hyperthyroidism in a non-selected group of patients admitted for contrast enhanced CT studies blood samples were tested for the levels of thyroid-stimulating hormone (TSH). Material and methods: TSH blood levels were obtained in 548 consecutive patients who were scheduled for contrast-enhanced (Iopromide; 300 mg iodine/ml) CT scanning. In case of TSH levels registered (sodium perchlorate) was commenced before scanning. In case of TSH levels < 0.1 mU/l, CT scanning was not performed but further evaluation of the thyroid function was initiated. Results: TSH blood levels ranged from 0.4 to 7.5 mU/l in 512 patients, and 36 patients (6.6%) had TSH blood levels < 0.4 mU/l and 9 patients blood levels < 0.1 mU/l, with 32 of those patients (5.8%) having regular T3 and T4 blood levels consistent with latent hyperthyroidism. In 4 patients (0.8%), T3 or T4 blood levels were increased consistent with manifest hyperthyroidism. Conclusion: in South Germany, the prevalence of latent or manifest hyperthyroidism in a non-selected patient group is high. Therefore TSH blood levels should be obtained prior to contrast-enhanced CT studies. (orig.)

  2. Characterisation of PDO olive oil Chianti Classico by non-selective (UV-visible, NIR and MIR spectroscopy) and selective (fatty acid composition) analytical techniques.

    Science.gov (United States)

    Casale, M; Oliveri, P; Casolino, C; Sinelli, N; Zunin, P; Armanino, C; Forina, M; Lanteri, S

    2012-01-27

    An authentication study of the Italian PDO (protected designation of origin) extra virgin olive oil Chianti Classico was performed; UV-visible (UV-vis), Near-Infrared (NIR) and Mid-Infrared (MIR) spectroscopies were applied to a set of samples representative of the whole Chianti Classico production area. The non-selective signals (fingerprints) provided by the three spectroscopic techniques were utilised both individually and jointly, after fusion of the respective profile vectors, in order to build a model for the Chianti Classico PDO olive oil. Moreover, these results were compared with those obtained by the gas chromatographic determination of the fatty acids composition. In order to characterise the olive oils produced in the Chianti Classico PDO area, UNEQ (unequal class models) and SIMCA (soft independent modelling of class analogy) were employed both on the MIR, NIR and UV-vis spectra, individually and jointly, and on the fatty acid composition. Finally, PLS (partial least square) regression was applied on the UV-vis, NIR and MIR spectra, in order to predict the content of oleic and linoleic acids in the extra virgin olive oils. UNEQ, SIMCA and PLS were performed after selection of the relevant predictors, in order to increase the efficiency of both classification and regression models. The non-selective information obtained from UV-vis, NIR and MIR spectroscopy allowed to build reliable models for checking the authenticity of the Italian PDO extra virgin olive oil Chianti Classico. Copyright © 2011 Elsevier B.V. All rights reserved.

  3. Selective versus non-selective culture medium for group B streptococcus detection in pregnancies complicated by preterm labor or preterm-premature rupture of membranes

    Directory of Open Access Journals (Sweden)

    Marcelo Luís Nomura

    Full Text Available The objective of this study was to identify group B streptococcus (GBS colonization rates and compare detection efficiency of selective versus non-selective culture media and anorectal versus vaginal cultures in women with preterm labor and preterm-premature rupture of membranes (PROM. A prospective cohort study of 203 women was performed. Two vaginal and two anorectal samples from each woman were collected using sterile swabs. Two swabs (one anorectal and one vaginal were placed separately in Stuart transport media and cultured in blood-agar plates for 48 hours; the other two swabs were inoculated separately in Todd-Hewitt selective media for 24 hours and then subcultured in blood-agar plates. Final GBS identification was made by the CAMP test. A hundred thrity-two cultures out of 812 were positive. The maternal colonization rate was 27.6%. Colonization rates were 30% for preterm PROM and 25.2% for preterm labor. Todd-Hewitt selective medium detected 87.5% and non-selective medium 60.7% GBS-positive women. Vaginal samples and anorectal samples had the same detection rate of 80.3%. Anorectal selective cultures detected 75% of carriers; 39% of GBS-positive women were detected only in selective medium. A combined vaginal-anorectal selective culture is appropriate for GBS screening in this population, minimizing laboratory costs.

  4. Economical Atomic Layer Deposition

    Science.gov (United States)

    Wyman, Richard; Davis, Robert; Linford, Matthew

    2010-10-01

    Atomic Layer Deposition is a self limiting deposition process that can produce films at a user specified height. At BYU we have designed a low cost and automated atomic layer deposition system. We have used the system to deposit silicon dioxide at room temperature using silicon tetrachloride and tetramethyl orthosilicate. Basics of atomic layer deposition, the system set up, automation techniques and our system's characterization are discussed.

  5. Optimation of Operation System Integration between Main and Feeder Public Transport (Case Study: Trans Jakarta-Kopaja Bus Services)

    Science.gov (United States)

    Miharja, M.; Priadi, Y. N.

    2018-05-01

    Promoting a better public transport is a key strategy to cope with urban transport problems which are mostly caused by a huge private vehicle usage. A better public transport service quality not only focuses on one type of public transport mode, but also concerns on inter modes service integration. Fragmented inter mode public transport service leads to a longer trip chain as well as average travel time which would result in its failure to compete with a private vehicle. This paper examines the optimation process of operation system integration between Trans Jakarta Bus as the main public transport mode and Kopaja Bus as feeder public transport service in Jakarta. Using scoring-interview method combined with standard parameters in operation system integration, this paper identifies the key factors that determine the success of the two public transport operation system integrations. The study found that some key integration parameters, such as the cancellation of “system setoran”, passenger get in-get out at official stop points, and systematic payment, positively contribute to a better service integration. However, some parameters such as fine system, time and changing point reliability, and information system reliability are among those which need improvement. These findings are very useful for the authority to set the right strategy to improve operation system integration between Trans Jakarta and Kopaja Bus services.

  6. From steep feeders to tabular plutons - Emplacement controls of syntectonic granitoid plutons in the Damara Belt, Namibia

    Science.gov (United States)

    Hall, Duncan; Kisters, Alexander

    2016-01-01

    Granitoid plutons in the deeply eroded south Central Zone of the Damara Belt in Namibia commonly show tabular geometries and pronounced stratigraphic controls on their emplacement. Subhorizontal, sheet-like pluton geometries record emplacement during regional subhorizontal shortening, but the intrusion of spatially and temporally closely-related granitoid plutons at different structural levels and in distinct structural settings suggests independent controls on their levels of emplacement. We describe and evaluate the controls on the loci of the dyke-to-sill transition that initiated the emplacement of three syntectonic (560-530 Ma) plutons in the basement-cover stratigraphy of the Erongo region. Intrusive relationships highlight the significance of (1) rigidity anisotropies associated with competent sedimentary packages or pre-existing subhorizontal granite sheets and (2) rheological anisotropies associated with the presence of thick ductile marble horizons. These mechanical anisotropies may lead to the initial deflection of steep feeder conduits as well as subsequent pluton assembly by the repeated underaccretion of later magma batches. The upward displacement of regional isotherms due to the heat advection associated with granite emplacement is likely to have a profound effect on the mechanical stratification of the upper crust and, consequently, on the level at which granitoid pluton emplacement is initiated. In this way, pluton emplacement at progressively shallower crustal depths may have resulted in the unusually high apparent geothermal gradients recorded in the upper crustal levels of the Damara Belt during its later evolution.

  7. Bacterial Feeders, the Nematode Caenorhabditis elegans and the Flagellate Cercomonas longicauda, have different Effects on Outcome of Competition among the Pseudomonas Biocontrol Strains CHA0 and DSS73

    DEFF Research Database (Denmark)

    Pedersen, Annette; Nybroe, Ole; Winding, Anne

    2009-01-01

    How bacterial feeding fauna affects colonization and survival of bacteria in soil is not well understood, which constrains the applicability of bacterial inoculants in agriculture. This study aimed to unravel how food quality of bacteria and bacterial feeders with different feeding habits (the......50090 or one of two biocontrol strains P. fluorescens CHA0 or Pseudomonas sp. DSS73) or combinations of two bacterial strains. DSM50090 is a suitable food bacterium, DSS73 is of intermediate food quality, and CHA0 is inedible to the bacterial feeders. Bacterial and protozoan cell numbers were measured...... predation pressure. Hence, the results suggested that the outcome of competition among bacteria depended on their ability to cope with the prevailing bacterial predator....

  8. THE METHOD OF SELECTION OF THE SETPOINT HIGH SPEED FEEDER SWITCH OF 3,3KV DC WITH MICROPROCESSOR-BASED PROTECTION SYSTEMS

    Directory of Open Access Journals (Sweden)

    P. Ye. Mykhalichenko

    2009-10-01

    Full Text Available In the article a new procedure of choice of minimum current jump for action of fast-acting switches of 3.3 kV DC traction substations intended for the use in the microprocessor protection system of feeders is described. This procedure is more perfect than existing one on the current increment and uses the results of mathematical simulation of the traction electric supply system.

  9. Differentiation of monkey embryonic stem cells to hepatocytes by feeder-free dispersion culture and expression analyses of cytochrome p450 enzymes responsible for drug metabolism.

    Science.gov (United States)

    Maruyama, Junya; Matsunaga, Tamihide; Yamaori, Satoshi; Sakamoto, Sakae; Kamada, Noboru; Nakamura, Katsunori; Kikuchi, Shinji; Ohmori, Shigeru

    2013-01-01

    We reported previously that monkey embryonic stem cells (ESCs) were differentiated into hepatocytes by formation of embryoid bodies (EBs). However, this EB formation method is not always efficient for assays using a large number of samples simultaneously. A dispersion culture system, one of the differentiation methods without EB formation, is able to more efficiently provide a large number of feeder-free undifferentiated cells. A previous study demonstrated the effectiveness of the Rho-associated kinase inhibitor Y-27632 for feeder-free dispersion culture and induction of differentiation of monkey ESCs into neural cells. In the present study, the induction of differentiation of cynomolgus monkey ESCs (cmESCs) into hepatocytes was performed by the dispersion culture method, and the expression and drug inducibility of cytochrome P450 (CYP) enzymes in these hepatocytes were examined. The cmESCs were successfully differentiated into hepatocytes under feeder-free dispersion culture conditions supplemented with Y-27632. The hepatocytes differentiated from cmESCs expressed the mRNAs for three hepatocyte marker genes (α-fetoprotein, albumin, CYP7A1) and several CYP enzymes, as measured by real-time polymerase chain reaction. In particular, the basal expression of cmCYP3A4 (3A8) in these hepatocytes was detected at mRNA and enzyme activity (testosterone 6β-hydroxylation) levels. Furthermore, the expression and activity of cmCYP3A4 (3A8) were significantly upregulated by rifampicin. These results indicated the effectiveness of Y-27632 supplementation for feeder-free dispersed culture and induction of differentiation into hepatocytes, and the expression of functional CYP enzyme(s) in cmESC-derived hepatic cells.

  10. Treatment with non-selective beta blockers is associated with reduced severity of systemic inflammation and improved survival of patients with acute-on-chronic liver failure

    DEFF Research Database (Denmark)

    Mookerjee, Rajeshwar P; Pavesi, Marco; Thomsen, Karen Louise

    2016-01-01

    BACKGROUND & AIMS: Non-selective beta blockers (NSBBs) have been shown to have deleterious outcomes in patients with refractory ascites, alcoholic hepatitis and spontaneous bacterial peritonitis leading many physicians to stop the drug in these cases. Acute-on-chronic liver failure (ACLF......) is characterized by systemic inflammation and high mortality. As NSBBs may have beneficial effects on gut motility and permeability and, systemic inflammation, the aims of this prospective, observational study were to determine whether ongoing use of NSBBs reduced 28-day mortality in ACLF patients. METHODS...... at enrollment significantly associated with treatment and mortality were taken into account as potential confounders to adjust for treatment effect. A logistic regression model was fitted. RESULTS: 164 (47%) ACLF patients received NSBBs whereas 185 patients did not. Although the CLIF-C ACLF scores were similar...

  11. A Frequency-Based Assignment Model under Day-to-Day Information Evolution of Oversaturated Conditions on a Feeder Bus Service

    Directory of Open Access Journals (Sweden)

    Silin Zhang

    2017-02-01

    Full Text Available Day-to-day information is increasingly being implemented in transit networks worldwide. Feeder bus service (FBS plays a vital role in a public transit network by providing feeder access to hubs and rails. As a feeder service, a space-time path for frequent passengers is decided by its dynamic strategy procedure, in which a day-to-day information self-learning mechanism is identified and analyzed from our survey data. We formulate a frequency-based assignment model considering day-to-day evolution under oversaturated conditions, which takes into account the residual capacity of bus and the comfort feelings of sitting or standing. The core of our proposed model is to allocate the passengers on each segment belonging to their own paths according to multi-utilities transformed from the time values and parametric demands, such as frequency, bus capacity, seat comfort, and stop layout. The assignment method, albeit general, allows us to formulate an equivalent optimization problem in terms of interaction between the FBS’ operation and frequent passengers’ rational behaviors. Finally, a real application case is generated to test the ability of the modeling framework capturing the theoretical consequents, serving the passengers’ dynamic externalities.

  12. Electro-Deposition Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The electro-deposition laboratory can electro-deposit various coatings onto small test samples and bench level prototypes. This facility provides the foundation for...

  13. Atmospheric Deposition Modeling Results

    Data.gov (United States)

    U.S. Environmental Protection Agency — This asset provides data on model results for dry and total deposition of sulfur, nitrogen and base cation species. Components include deposition velocities, dry...

  14. Calcium Pyrophosphate Deposition (CPPD)

    Science.gov (United States)

    ... Patient / Caregiver Diseases & Conditions Calcium Pyrophosphate Deposition (CPPD) Calcium Pyrophosphate Deposition (CPPD) Fast Facts The risk of ... young people, too. Proper diagnosis depends on detecting calcium pyrophosphate crystals in the fluid of an affected ...

  15. Efficient Generation and Editing of Feeder-free IPSCs from Human Pancreatic Cells Using the CRISPR-Cas9 System.

    Science.gov (United States)

    Nandal, Anjali; Mallon, Barbara; Telugu, Bhanu P

    2017-11-08

    Embryonic and induced pluripotent stem cells can self-renew and differentiate into multiple cell types of the body. The pluripotent cells are thus coveted for research in regenerative medicine and are currently in clinical trials for eye diseases, diabetes, heart diseases, and other disorders. The potential to differentiate into specialized cell types coupled with the recent advances in genome editing technologies including the CRISPR/Cas system have provided additional opportunities for tailoring the genome of iPSC for varied applications including disease modeling, gene therapy, and biasing pathways of differentiation, to name a few. Among the available editing technologies, the CRISPR/Cas9 from Streptococcus pyogenes has emerged as a tool of choice for site-specific editing of the eukaryotic genome. The CRISPRs are easily accessible, inexpensive, and highly efficient in engineering targeted edits. The system requires a Cas9 nuclease and a guide sequence (20-mer) specific to the genomic target abutting a 3-nucleotide "NGG" protospacer-adjacent-motif (PAM) for targeting Cas9 to the desired genomic locus, alongside a universal Cas9 binding tracer RNA (together called single guide RNA or sgRNA). Here we present a step-by-step protocol for efficient generation of feeder-independent and footprint-free iPSC and describe methodologies for genome editing of iPSC using the Cas9 ribonucleoprotein (RNP) complexes. The genome editing protocol is effective and can be easily multiplexed by pre-complexing sgRNAs for more than one target with the Cas9 protein and simultaneously delivering into the cells. Finally, we describe a simplified approach for identification and characterization of iPSCs with desired edits. Taken together, the outlined strategies are expected to streamline generation and editing of iPSC for manifold applications.

  16. Mixed xylem and phloem sap ingestion in sheath-feeders as normal dietary behavior: Evidence from the leafhopper Scaphoideus titanus.

    Science.gov (United States)

    Chuche, Julien; Sauvion, Nicolas; Thiéry, Denis

    2017-10-01

    In phytophagous piercing-sucking insects, salivary sheath-feeding species are often described as xylem- or phloem-sap feeding specialists. Because these two food sources have very different characteristics, two feeding tactics are often associated with this supposed specialization. Studying the feeding behavior of insects provides substantial information on their biology, ecology, and evolution. Furthermore, study of feeding behavior is of primary importance to elucidate the transmission ability of insects that act as vectors of plant pathogens. In this study, we compared the durations of ingestion performed in xylem versus phloem by a leafhopper species, Scaphoideus titanus Ball, 1932. This was done by characterizing and statistically analyzing electrical signals recorded using the electropenetrography technique, derived from the feeding behaviors of males and females. We identified three groups of S. titanus based on their feeding behavior: 1) a group that reached the phloem quickly and probed for a longer time in phloem tissue than the other groups, 2) a group that reached the xylem quickly and probed for a longer time in xylem tissue than the other groups, and 3) a group where individuals did not ingest much sap. In addition, the numbers and durations of waveforms representing ingestion of xylem and phloem saps differed significantly depending on the sex of the leafhopper, indicating that the two sexes exhibit different feeding behaviors. Males had longer phloem ingestion events than did females, which indicates that males are greater phloem feeders than females. These differences are discussed, specifically in relation to hypotheses about evolution of sap feeding and phytoplasma transmission from plant to plant. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. BODY SIZE AND HAREM SIZE IN MALE RED-WINGED BLACKBIRDS: MANIPULATING SELECTION WITH SEX-SPECIFIC FEEDERS.

    Science.gov (United States)

    Rohwer, Sievert; Langston, Nancy; Gori, Dave

    1996-10-01

    We experimentally manipulated the strength of selection in the field on red-winged blackbirds (Agelaius phoeniceus) to test hypotheses about contrasting selective forces that favor either large or small males in sexually size dimorphic birds. Selander (1972) argued that sexual selection favors larger males, while survival selection eventually stabilizes male size because larger males do not survive as well as smaller males during harsh winters. Searcy (1979a) proposed instead that sexual selection may be self limiting: male size might be stabilized not by overwinter mortality, but by breeding-season sexual selection that favors smaller males. Under conditions of energetic stress, smaller males should be able to display more and thus achieve higher reproductive success. Using feeders that provisioned males or females but not both, we produced conditions that mimicked the extremes of natural conditions. We found experimental support for the hypothesis that when food is abundant, sexual selection favors larger males. But even under conditions of severe energetic stress, smaller males did not gain larger harems, as the self-limiting hypothesis predicted. Larger males were more energetically stressed than smaller males, but in ways that affected their future reproductive output rather than their current reproductive performance. Stressed males that returned had smaller wings and tails than those that did not return; among returning stressed males, relative harem sizes were inversely related to wing and tail length. Thus, male body size may be stabilized not by survival costs during the non-breeding season, nor by energetic costs during the breeding season, but by costs of future reproduction that larger males pay for their increased breeding-season effort. © 1996 The Society for the Study of Evolution.

  18. Application of a computer model to predict optimum slaughter end points for different biological types of feeder cattle.

    Science.gov (United States)

    Williams, C B; Bennett, G L

    1995-10-01

    A bioeconomic model was developed to predict slaughter end points of different genotypes of feeder cattle, where profit/rotation and profit/day were maximized. Growth, feed intake, and carcass weight and composition were simulated for 17 biological types of steers. Distribution of carcass weight and proportion in four USDA quality and five USDA yield grades were obtained from predicted carcass weights and composition. Average carcass value for each genotype was calculated from these distributions under four carcass pricing systems that varied from value determined on quality grade alone to value determined on yield grade alone. Under profitable market conditions, rotation length was shorter and carcass weights lighter when the producer's goal was maximum profit/day, compared with maximum profit/rotation. A carcass value system based on yield grade alone resulted in greater profit/rotation and in lighter and leaner carcasses than a system based on quality grade alone. High correlations ( > .97) were obtained between breed profits obtained with different sets of input/output prices and carcass price discount weight ranges. This suggests that breed rankings on the basis of breed profits may not be sensitive to changes in input/output market prices. Steers that were on a grower-stocker system had leaner carcasses, heavier optimum carcass weight, greater profits, and less variation in optimum carcass weights between genotypes than steers that were started on a high-energy finishing diet at weaning. Overall results suggest that breed choices may change with different carcass grading and value systems and postweaning production systems. This model has potential to provide decision support in marketing fed cattle.

  19. Wean-to-finish feeder space availability effects on nursery and finishing pig performance and total tract digestibility in a commercial setting when feeding dried distillers grains with solubles.

    Science.gov (United States)

    Weber, E K; Stalder, K J; Patience, J F

    2015-04-01

    The study objectives were to determine nursery phase feeder space allowance effects on pig performance when double stocked and, second, to determine feeder space allowance and dried distillers grains with solubles (DDGS) inclusion level effects on pig performance and nutrient digestibility during the growing-finishing phase. This study was performed on the same group of pigs within a commercial wean-finish system. For the nursery phase, a completely randomized design was used to compare 3 feeder space allowance treatments (2.1, 2.5, and 2.9 cm/pig). A total of 3,720 pigs were randomly allotted to same-sex pens (10 feeders/treatment) housing 62 pigs/pen. Thirty 7-hole, double-sided feeders were utilized in the study. Differing linear feeder space treatments were established by blocking off sections for the nursery and grow-finish portions of this experiment. All pigs were provided equal floor space (0.26 m2/pig). In the grow-finish phase, a total of 1,860 pigs (n = 60 pens) were utilized in a 2 × 3 factorial design with 3 feeder space allowances (4.1, 4.9, or 5.7 cm/pig) and 2 dietary DDGS treatments (30% [D30] or 60% [D60]). Fecal and diet samples were collected and analyzed to estimate apparent total tract digestibility percentage (ATTD %). In the nursery portion of the trial, there was no feeder space treatment effect on ADG, ADFI, or feed efficiency (P > 0.10) from weaning to d 56 postweaning or during any weigh period. In the grow-finish portion of the trial, feeder space allowance and DDGS inclusion level did not affect ADG, ADFI, or feed efficiency (P > 0.05) from d 57 postweaning to market. Pigs fed the D30 diet had greater HCW, percent yield, and loin depth than those on the D60 diet (P feeder space allowance did not impact pig performance during the nursery or grow-finish production phases. Inclusion of DDGS at higher levels will decrease ADFI but not ADG or efficiency when isocaloric diets are fed. The inclusion level of DDGS does impact HCW and percent

  20. Acid Deposition Phenomena

    International Nuclear Information System (INIS)

    Ramadan, A.E.K.

    2004-01-01

    Acid deposition, commonly known as acid rain, occurs when emissions from the combustion of fossil fuels and other industrial processes undergo complex chemical reactions in the atmosphere and fall to the earth as wet deposition (rain, snow, cloud, fog) or dry deposition (dry particles, gas). Rain and snow are already naturally acidic, but are only considered problematic when less than a ph of 5.0 The main chemical precursors leading to acidic conditions are atmospheric concentrations of sulfur dioxide (SO 2 ) and nitrogen oxides (NO x ). When these two compounds react with water, oxygen, and sunlight in the atmosphere, the result is sulfuric (H 2 SO 4 ) and nitric acids (HNO 3 ), the primary agents of acid deposition which mainly produced from the combustion of fossil fuel and from petroleum refinery. Airborne chemicals can travel long distances from their sources and can therefore affect ecosystems over broad regional scales and in locations far from the sources of emissions. According to the concern of petroleum ministry with the environment and occupational health, in this paper we will discussed the acid deposition phenomena through the following: Types of acidic deposition and its components in the atmosphere Natural and man-made sources of compounds causing the acidic deposition. Chemical reactions causing the acidic deposition phenomenon in the atmosphere. Factors affecting level of acidic deposition in the atmosphere. Impact of acid deposition. Procedures for acidic deposition control in petroleum industry

  1. The role of Homer 1a in increasing locomotor activity and non-selective attention, and impairing learning and memory abilities.

    Science.gov (United States)

    Yang, Lei; Hong, Qin; Zhang, Min; Liu, Xiao; Pan, Xiao-Qin; Guo, Mei; Fei, Li; Guo, Xi-Rong; Tong, Mei-Ling; Chi, Xia

    2013-06-17

    The current study aimed to investigate the possible role of Homer 1a in the etiology and pathogenesis of attention deficit hyperactivity disorder (ADHD). We divided 32 rats into four groups. The rats in the RNAi-MPH group were given the lentiviral vector containing Homer 1a-specific miRNA (Homer 1a-RNAi-LV) by intracerebroventricular injection, and 7 days later they were given three daily doses of methylphenidate (MPH) by intragastric gavage. The RNAi-SAL group was given Homer 1a-RNAi-LV and saline later. The NC-MPH group was given the negative control lentiviral vector (NC-LV) and MPH later. The NC-SAL group was given NC-LV and saline later. Rats that were given Homer 1a RNAi exhibited increased locomotor activity and non-selective attention, and impaired learning and memory abilities, which is in line with the behavioral findings of animal models of ADHD. However, MPH ameliorated these abnormal behaviors. All findings indicated that Homer 1a may play an important role in the etiology and pathogenesis of ADHD. Copyright © 2013 Elsevier B.V. All rights reserved.

  2. Gastric and renal effects of COX-2 selective and non-selective NSAIDs in rats receiving low-dose aspirin therapy

    Directory of Open Access Journals (Sweden)

    Marcella Goetz MORO

    Full Text Available Abstract The consumption of low-dose aspirin (LDA to prevent cardiovascular disease continues to increase worldwide. Consequently, the number of chronic LDA users seeking dental procedures that require complementary acute anti-inflammatory medication has also grown. Considering the lack of literature evaluating this interaction, we analyzed the gastric and renal effects caused by a selective COX-2 inhibitor (etoricoxib and a non-selective COX-2 inhibitor (ibuprofen nonsteroidal anti-inflammatory drug (NSAID in rats receiving chronic LDA therapy. Male Wistar rats were divided into six experimental groups (carboxymethylcellulose (CMC - vehicle; LDA; LDA + ibuprofen; ibuprofen; LDA + etoricoxib; and etoricoxib and submitted to long-term LDA therapy with a subsequent NSAID administration for three days by gavage. After the experimental period, we analyzed gastric and renal tissues and quantified serum creatinine levels. The concomitant use of LDA with either NSAID induced the highest levels of gastric damage when compared to the CMC group (F = 20.26, p 0.05. These results suggest that even the acute use of an NSAID (regardless of COX-2 selectivity can induce gastric damage when combined with the long-term use of low-dose aspirin in an animal model. Additional studies, including clinical assessments, are thus needed to clarify this interaction, and clinicians should be careful of prescribing NSAIDs to patients using LDA.

  3. Impact of non-selective fungicides on the growth and production of ochratoxin A by Aspergillus ochraceus and A. carbonarius in barley-based medium.

    Science.gov (United States)

    Mateo, Eva M; Valle-Algarra, F M; Mateo-Castro, R; Jimenez, M

    2011-01-01

    The aim of this study was to assess the influence of the non-selective fungicides mancozeb, copper oxychloride, and sulfur on the growth and capability for producing ochratoxin A (OTA) of ochratoxigenic isolates of Aspergillus carbonarius and A. ochraceus in barley-based medium. Lag phases and growth rates were determined for each fungicide at different doses, at 15°C and 25°C and at 0.97 a(w). Mancozeb at 40 mg l(-1 )inhibited fungal growth and provided lag phases >24 days at 10-20 mg l(-1) and 15°C. OTA was observed only at 25°C and doses Sulfur was inhibitory or provided large lag phases at 5-8 g l(-1) (at 15°C) while at 25°C growth took place even at 8 g l(-1), although OTA levels were low or undetectable. The antifungal activity decreased in the order mancozeb > copper oxychloride > sulfur, and was lower at 25°C than at 15°C. OTA accumulation was affected by the type of fungicide, dose, temperature and time. The efficacy of these fungicides on the growth of A. carbonarius and A. ochraceus and OTA production in barley-based medium is assessed for the first time.

  4. Generation of megakaryocytic progenitors from human embryonic stem cells in a feeder- and serum-free medium.

    Directory of Open Access Journals (Sweden)

    Marjorie Pick

    Full Text Available BACKGROUND: The production of human platelets from embryonic stem cells in a defined culture system is a prerequisite for the generation of platelets for therapeutic use. As an important step towards this goal, we report the differentiation of human embryonic stem cells (hESCs towards the megakaryocyte (Mk lineage using a 'spin embryoid body' method in serum-free differentiation medium. METHODOLOGY AND PRINCIPAL FINDINGS: Immunophenotypic analyses of differentiating hESC identified a subpopulation of cells expressing high levels of CD41a that expressed other markers associated with the Mk lineage, including CD110, CD42b and CD61. Differentiated cells were sorted on the basis of their expression of CD41a, CD34 and CD45 and assessed for Mk colony formation, expression of myeloid and Mk genes and ability to endoreplicate DNA. In a collagen-based colony assay, the CD41a⁺ cells sorted from these differentiation cultures produced 100-800 Mk progenitors at day 13 and 25-160 Mk progenitors at day 20 of differentiation per 100,000 cells assayed. Differentiated Mk cells produced platelet-like particles which expressed CD42b and were activated by ADP, similar to platelets generated from precursors in cord blood. These studies were complemented by real time PCR analyses showing that subsets of cells enriched for CD41a⁺ Mk precursors expressed high levels of Mk associated genes such as PF4 and MPL. Conversely, high levels of myeloid and erythroid related transcripts, such as GATA1, TAL1/SCL and PU.1, were detected in sorted fractions containing CD34⁺ and CD45⁺ cells. CONCLUSIONS: We describe a serum- and feeder-free culture system that enabled the generation of Mk progenitors from human embryonic stem cells. These cells formed colonies that included differentiated Mks that fragmented to form platelet-like particles. This protocol represents an important step towards the generation of human platelets for therapeutic use.

  5. A simple and efficient feeder-free culture system to up-scale iPSCs on polymeric material surface for use in 3D bioprinting.

    Science.gov (United States)

    Wong, Chui-Wei; Chen, You-Tzung; Chien, Chung-Liang; Yu, Tien-Yu; Rwei, Syang-Peng; Hsu, Shan-Hui

    2018-01-01

    The 3D bioprinting and cell/tissue printing techniques open new possibilities for future applications. To facilitate the 3D bioprinting process, a large amount of living cells are required. Induced pluripotent stem cells (iPSCs) represent a promising cell source for bioprinting. However, the maintenance and expansion of undifferentiated iPSCs are expensive and time consuming. Therefore, in this study a culture method to obtain a sufficient amount of healthy and undifferentiated iPSCs in a short-term period was established. The iPSCs could be passaged for twice on tissue culture polystyrene (TCPS) dish with the conditional medium and could adapt to the feeder-free environment. Feeder-free dishes were further prepared from chitosan, chitosan-hyaluronan, silk fibroin, and polyurethane (PU1 and PU2) two-dimensional substrates. The iPSCs cultured on the chitosan substrates showed a higher proliferation rate without losing the stemness feature. Among the different materials, PU2 could be prepared as a thermoresponsive hydrogel, which was a potential ink for 3D bioprinting. The iPSCs cultured on PU2 substrates well survived when further embedded in PU2 hydrogel. Moreover, PU2 hydrogel printed with iPSCs remained structural integrity. The use of PU2 hydrogel to embed iPSCs reduced the injury to iPSCs by shear stress. These results indicate that iPSCs could be expanded on chitosan or PU2 membranes without the feeder layer and then printed in PU2 hydrogel. The combination of these steps could offer a new possibility for future applications of iPSC-based 3D bioprinting in tissue engineering. Copyright © 2017 Elsevier B.V. All rights reserved.

  6. Deposition Measurements in NSTX

    Science.gov (United States)

    Skinner, C. H.; Kugel, H. W.; Hogan, J. T.; Wampler, W. R.

    2004-11-01

    Two quartz microbalances have been used to record deposition on the National Spherical Torus Experiment. The experimental configuration mimics a typical diagnostic window or mirror. An RS232 link was used to acquire the quartz crystal frequency and the deposited thickness was recorded continuously with 0.01 nm resolution. Nuclear Reaction Analysis of the deposit was consistent with the measurement of the total deposited mass from the change in crystal frequency. We will present measurements of the variation of deposition with plasma conditions. The transport of carbon impurities in NSTX has been modelled with the BBQ code. Preliminary calculations indicated a negligible fraction of carbon generated at the divertor plates in quiescent discharges directly reaches the outer wall, and that transient events are responsible for the deposition.

  7. Shedding of ash deposits

    DEFF Research Database (Denmark)

    Zbogar, Ana; Frandsen, Flemming; Jensen, Peter Arendt

    2009-01-01

    Ash deposits formed during fuel thermal conversion and located on furnace walls and on convective pass tubes, may seriously inhibit the transfer of heat to the working fluid and hence reduce the overall process efficiency. Combustion of biomass causes formation of large quantities of troublesome...... ash deposits which contain significant concentrations of alkali, and earth-alkali metals. The specific composition of biomass deposits give different characteristics as compared to coal ash deposits, i.e. different physical significance of the deposition mechanisms, lower melting temperatures, etc....... Low melting temperatures make straw ashes especially troublesome, since their stickiness is higher at lower temperatures, compared to coal ashes. Increased stickiness will eventually lead to a higher collection efficiency of incoming ash particles, meaning that the deposit may grow even faster...

  8. Trophodynamics of inorganic pollutants in a wide-range feeder: The relevance of dietary inputs and biomagnification in the Yellow-legged gull (Larus michahellis)

    International Nuclear Information System (INIS)

    Ramos, Raül; Ramírez, Francisco; Jover, Lluís

    2013-01-01

    The suitability of sentinel species to monitor environmental pollution is often hampered by an insufficient knowledge on pollutant trophodynamics. We simultaneously evaluated the influence of individuals' trophic position (as revealed by δ 15 N values) and dietary exploitation of particular systems (using δ 13 C and δ 34 S as proxies) on inorganic pollutant concentrations measured on fledglings' feathers of a wide-range feeder, the Yellow-legged Gull (Larus michahellis), sampled at four locations throughout the Western Mediterranean. Concentrations of total Hg and Se in fledgling feathers (2.43 ± 1.30 and 1.16 ± 0.43 μg/g, respectively) were under the threshold points for deleterious effects on seabirds. On the contrary, alarming Pb concentrations were found in one colony (mean: 1.57 ± 2.46 μg/g, range: 0.16–12.13). With the exception of Pb, pollutant concentrations were positively influenced by consumption of marine resources (as suggested by the positive relationship with δ 34 S values), whereas trophic position played a minor role in determining pollutant body burdens. - Graphical abstract: Individual feeding behaviours in wide-range feeders may represent unavoidable knowledge for an appropriate understanding of contaminant acquisition, adding complexity to the study of the dynamic of contaminants throughout food chains. In this case study, pollutant body burden of Yellow-legged gull (Larus michahellis) chicks was highly influenced by dietary exposure, whereas the influence of trophic position was relatively low. Display Omitted Highlights: ► Diet origin (δ 34 S) and trophic position (δ 15 N) were tested relative to Hg, Se, and Pb levels. ► Hg and Se concentrations in gull feathers were highly influenced by δ 34 S signatures. ► Exploited habitat influenced pollutant levels to a greater extent than trophic position. ► Biomagnification processes contribute less to contamination exposure in wide-range feeders. - Pollutant body burden of a wide

  9. Human amniotic epithelial cell feeder layers maintain human iPS cell pluripotency via inhibited endogenous microRNA-145 and increased Sox2 expression

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Te, E-mail: liute79@yahoo.com [School of Environmental Science and Engineering, Donghua University, Shanghai 201620 (China); Shanghai Geriatric Institute of Chinese Medicine, Shanghai 200031 (China); Cheng, Weiwei [International Peace Maternity and Child Health Hospital, Shanghai Jiaotong University, Shanghai 200030 (China); Huang, Yongyi [Laboratoire PROTEE, Batiment R, Universite du Sud Toulon-Var, 83957 LA GARDE Cedex (France); Huang, Qin; Jiang, Lizhen [Institute of Biochemistry and Cell Biology, Shanghai Institute for Biological Sciences, Chinese Academy of Sciences, Shanghai 200031 (China); Guo, Lihe, E-mail: liute79@yahoo.com [Institute of Biochemistry and Cell Biology, Shanghai Institute for Biological Sciences, Chinese Academy of Sciences, Shanghai 200031 (China)

    2012-02-15

    Currently, human induced pluripotent stem (iPS) cells were generated from patient or disease-specific sources and share the same key properties as embryonic stem cells. This makes them attractive for personalized medicine, drug screens or cellular therapy. Long-term cultivation and maintenance of normal iPS cells in an undifferentiated self-renewing state are a major challenge. Our previous studies have shown that human amniotic epithelial cells (HuAECs) could provide a good source of feeder cells for mouse and human embryonic stem cells, or spermatogonial stem cells, but the mechanism for this is unknown. Here, we examined the effect of endogenous microRNA-145 regulation on Sox2 expression in human iPS cells by HuAECs feeder cells regulation, and in turn on human iPS cells pluripotency. We found that human IPS cells transfected with a microRNA-145 mutant expressed Sox2 at high levels, allowing iPS to maintain a high level of AP activity in long-term culture and form teratomas in SCID mice. Expression of stem cell markers was increased in iPS transfected with the microRNA-145 mutant, compared with iPS was transfected with microRNA-145. Besides, the expression of Drosha proteins of the microRNA-processor complex, required for the generation of precursor pre-miRNA, was significantly increased in human iPS cells cultured on MEF but not on HuAECs. Taken together, these results suggest that endogenous Sox2 expression may be regulated by microRNA-145 in human iPS cells with HuAECs feeder cells, and Sox2 is a crucial component required for maintenance of them in an undifferentiated, proliferative state capable of self-renewal. Highlights: Black-Right-Pointing-Pointer microRNA-145 inhibits Sox2 expression in human iPS cells. Black-Right-Pointing-Pointer microRNA-145 suppresses the self-renewal and pluripotency of human iPS cells. Black-Right-Pointing-Pointer HuAECs regulate expression of microRNA-145 and Sox2 in human iPS cells. Black-Right-Pointing-Pointer HuAECs feeder

  10. Human amniotic epithelial cell feeder layers maintain human iPS cell pluripotency via inhibited endogenous microRNA-145 and increased Sox2 expression

    International Nuclear Information System (INIS)

    Liu, Te; Cheng, Weiwei; Huang, Yongyi; Huang, Qin; Jiang, Lizhen; Guo, Lihe

    2012-01-01

    Currently, human induced pluripotent stem (iPS) cells were generated from patient or disease-specific sources and share the same key properties as embryonic stem cells. This makes them attractive for personalized medicine, drug screens or cellular therapy. Long-term cultivation and maintenance of normal iPS cells in an undifferentiated self-renewing state are a major challenge. Our previous studies have shown that human amniotic epithelial cells (HuAECs) could provide a good source of feeder cells for mouse and human embryonic stem cells, or spermatogonial stem cells, but the mechanism for this is unknown. Here, we examined the effect of endogenous microRNA-145 regulation on Sox2 expression in human iPS cells by HuAECs feeder cells regulation, and in turn on human iPS cells pluripotency. We found that human IPS cells transfected with a microRNA-145 mutant expressed Sox2 at high levels, allowing iPS to maintain a high level of AP activity in long-term culture and form teratomas in SCID mice. Expression of stem cell markers was increased in iPS transfected with the microRNA-145 mutant, compared with iPS was transfected with microRNA-145. Besides, the expression of Drosha proteins of the microRNA-processor complex, required for the generation of precursor pre-miRNA, was significantly increased in human iPS cells cultured on MEF but not on HuAECs. Taken together, these results suggest that endogenous Sox2 expression may be regulated by microRNA-145 in human iPS cells with HuAECs feeder cells, and Sox2 is a crucial component required for maintenance of them in an undifferentiated, proliferative state capable of self-renewal. Highlights: ► microRNA-145 inhibits Sox2 expression in human iPS cells. ► microRNA-145 suppresses the self-renewal and pluripotency of human iPS cells. ► HuAECs regulate expression of microRNA-145 and Sox2 in human iPS cells. ► HuAECs feeder layers maintain human iPS cells pluripotency. ► HuAECs negatively regulates the synthesis of

  11. Belt deviation and its solution of belt weighing feeder machine%皮带称重绐料机皮带跑偏问题殁对策

    Institute of Scientific and Technical Information of China (English)

    张荣轩

    2012-01-01

    This article analyzes the reasons of common belt deviation problems during the using of belt weighing feeder machine, and combining practical work experience, proposed its solutions.%本文就皮带称重给料机在使用过程中常见的皮带跑偏问题进行了原因分析,并结合本人多年的工作实践经验,提出其相应的解决办法。

  12. Quantitative control of belt weighing feeder quick loading system%定量控制皮带称重式给料机快速装车系统

    Institute of Scientific and Technical Information of China (English)

    张荣轩

    2012-01-01

    This paper introduces a kind of belt weighing feeder quantitative control technology, which realizes the bulk material rapid loading design and widely used in coal metallurgy, chemical industry, building materials industry.%本文介绍了一种对皮带称重式给料机进行定量控制技术,实现散状物料快速装车的设计方案,广泛适用于煤炭、冶金、化工和建材等行业。

  13. Weaning age of calves fed a high milk allowance by automated feeders: effects on feed, water, and energy intake, behavioral signs of hunger, and weight gains.

    Science.gov (United States)

    de Passillé, A M; Borderas, T F; Rushen, J

    2011-03-01

    Dairy calves are increasingly fed large volumes of milk, which reduces feeding motivation and improves weight gain. However, calves often show signs of hunger and lose weight when weaned off milk due to low starter intake. We examined whether delaying the age at weaning would reduce responses to weaning. Calves were raised in groups of 9 and fed milk, starter, hay, and water with automated feeders. In each group, 3 calves were randomly assigned to 1 of 3 treatments: (1) low-milk, early-weaned: fed 6 L/d of milk and weaned at 47 d of age; (2) high-milk early-weaned: fed 12 L/d of milk and weaned at 47 d; (3) high-milk later-weaned: fed 12 L/d of milk and weaned at 89 d of age. Milk, starter, and hay intakes were recorded daily and digestible energy (DE) intake estimated. Feeder visits were recorded. Before weaning, the high-milk calves drank more milk, ate less starter and hay, but had higher DE intakes, gained more weight, and made fewer visits to the milk feeder than the low-milk, early-weaned calves. During and immediately after weaning, the high-fed, early-weaned calves ate less starter and hay, had lower DE intakes, and gained less weight than the low-milk, early-weaned calves and lost their body weight advantage 7 d after weaning. During and immediately after weaning, the high-milk, later-weaned calves ate more starter and hay and had higher DE intakes, higher weight gains, and made fewer visits to the milk feeder than the high-milk, early-weaned calves. They were still heavier than the low-milk, early-weaned calves 18 d after weaning. Delaying the age at which calves are weaned off milk reduces the drop in energy intake and behavioral signs of hunger that result from weaning. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  14. The Cost of Distribution System Upgrades to Accommodate Increasing Penetrations of Distributed Photovoltaic Systems on Real Feeders in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Horowitz, Kelsey A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Ding, Fei [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Mather, Barry A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Palmintier, Bryan S [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2018-04-05

    The increasing deployment of distributed photovoltaic systems (DPV) can impact operations at the distribution level and the transmission level of the electric grid. It is important to develop and implement forward-looking approaches for calculating distribution upgrade costs that can be used to inform system planning, market and tariff design, cost allocation, and other policymaking as penetration levels of DPV increase. Using a bottom-up approach that involves iterative hosting capacity analysis, this report calculates distribution upgrade costs as a function of DPV penetration on three real feeders - two in California and one in the Northeastern United States.

  15. Uraniferous surficial deposits

    International Nuclear Information System (INIS)

    Toens, P.D.; Hambleton-Jones, B.B.

    1980-10-01

    As a result of the discovery of uranium in surficial deposits of Tertiary to Recent age, in Australia and Southern Africa, increasing attention is being paid to the location and understanding of the genesis of these deposits. The paper discusses the definitions and terminology currently in use and a classification of these deposits is presented. It is concluded that in order to obtain a measure of clarity, the terms calcrete, gypcrete and dolocrete should not be used to describe the uraniferous valley-fill deposits of Southern Africa and Australia [af

  16. Bioecology of the conifer swift moth, Korscheltellus gracilis, a root feeder associated with spruce-fir decline

    Science.gov (United States)

    William E. Wallner; David L. Wagner; Bruce L. Parker; Donald L. Tobi

    1991-01-01

    During the past two decades, the decline of red spruce, Picea rubens Sargent, and balsam fir, Abies balsamea (L), at high elevations (900-1200 m) in eastern North America has evoked concern about the effects of anthropogenic deposition upon terrestrial ecosystems. In many high-elevation forests across New England, as many as 50...

  17. Deposition of organic material in a coral reef lagoon, One Tree Island, Great Barrier Reef

    Science.gov (United States)

    Koop, K.; Larkum, A. W. D.

    1987-07-01

    Deposition of organic material was measured at four sites on One Tree Island coral reef using fixed sediment traps. Although no reliable data were obtained for the reef crest area because of problems of resuspension, mean deposition in the backreef area amounted to some 4 g organic C m -2 day -1 whereas in the lagoon it was about 1·5 g C m -2 day -1. This amounted to mean nitrogen deposition rates of 160 and 95 mg N m -2 day -1, respectively. As primary production by turf algae, the principal producers at One Tree Island, has been estimated at about 2·3 g C m -2 day -1 for the whole reef system and the weighted mean carbon deposition is estimated at 2·2 g C m -2 day -1, it is clear that the carbon produced by plants is largely retained in the system. Nitrogen deposition, on the other hand, amounted to only about 60% of that produced by turf algae and it must be assumed that much of this leached into the water during sedimentation. Losses of nitrogen may be minimized by incorporation of dissolved nitrogen by pelagic microheterotrophs which may in turn be consumed by filter feeders before they leave the reef.

  18. COMPARISON OF SELECTIVE AND NON SELECTIVE CYCLO-OXYGENASE 2 INHIBITORS IN EXPERIMENTAL COLITIS EXACERBATION: role of leukotriene B4 and superoxide dismutase

    Directory of Open Access Journals (Sweden)

    José Wander BREGANÓ

    2014-09-01

    Full Text Available Context Nonsteroidal anti-inflammatory drugs are considered one of the most important causes of reactivation of inflammatory bowel disease. With regard to selective cyclo-oxygenase 2 inhibitors, the results are controversial in experimental colitis as well as in human studies. Objectives The aim this study is to compare nonsteroidal anti-inflammatory drugs effects, selective and non selective cyclo-oxygenase 2 inhibitors, in experimental colitis and contribute to the understanding of the mechanisms which nonsteroidal anti-inflammatory drugs provoke colitis exacerbation. Methods Six groups of rats: without colitis, with colitis, and colitis treated with celecoxib, ketoprofen, indometacin or diclofenac. Survival rates, hemoglobin, plasmatic albumin, colonic tissue of interleukin-1ß, interleukin-6, tumor necrosis factor alpha, prostaglandin E2, catalase, superoxide dismutase, thiobarbituric acid-reactive substances, chemiluminescence induced by tert-butil hydroperoxides, and tissue and plasmatic leukotriene B4 were determined. Results The groups treated with diclofenac or indometacin presented lower survival rates, hemoglobin and albumin, higher tissue and plasmatic leukotriene B4 and tissue superoxide dismutase than the group treated with celecoxib. Ketoprofen presented an intermediary behavior between diclofenac/indometacin and celecoxib, concerning to survival rate and albumin. The groups without colitis, with colitis and with colitis treated with celecoxib showed leukotriene B4 and superoxide dismutase lower levels than the groups treated with nonselective cyclo-oxygenase 2 inhibitors. Conclusions Diclofenac and indometacin presented the highest degree of induced colitis exacerbation with nonsteroidal anti-inflammatory drugs, celecoxib did not show colitis exacerbation, and ketoprofen presented an intermediary behavior between diclofenac/indometacin and celecoxib. These results suggest that leukotriene B4 and superoxide dismutase can be

  19. The selective and non-selective cyclooxygenase inhibitors valdecoxib and piroxicam induce the same postoperative analgesia and control of trismus and swelling after lower third molar removal

    Directory of Open Access Journals (Sweden)

    V. Benetello

    2007-08-01

    Full Text Available We compared the clinical efficacy of orally administered valdecoxib and piroxicam for the prevention of pain, trismus and swelling after removal of horizontally and totally intrabony impacted lower third molars. Twenty-five patients were scheduled to undergo removal of symmetrically positioned lower third molars in two separate appointments. Valdecoxib (40 mg or piroxicam (20 mg was administered in a double-blind, randomized and crossed manner for 4 days after the surgical procedures. Objective and subjective parameters were recorded for comparison of postoperative courses. Both agents were effective for postoperative pain relief (N = 19. There was a similar mouth opening at suture removal compared with the preoperative values (86.14 ± 4.36 and 93.12 ± 3.70% of the initial measure for valdecoxib and piroxicam, respectively; ANOVA. There was no significant difference regarding the total amount of rescue medication taken by the patients treated with valdecoxib or piroxicam (173.08 ± 91.21 and 461.54 ± 199.85 mg, respectively; Wilcoxon test. There were no significant differences concerning the swelling observed on the second postoperative day compared to baseline measures (6.15 ± 1.84 and 8.46 ± 2.04 mm for valdecoxib and piroxicam, respectively; ANOVA or on the seventh postoperative day (1.69 ± 1.61 and 2.23 ± 2.09 mm for valdecoxib and piroxicam, respectively; ANOVA. The cyclooxygenase-2 selective inhibitor valdecoxib is as effective as the non-selective cyclooxygenase inhibitor piroxicam for pain, trismus and swelling control after removal of horizontally and totally intrabony impacted lower third molars.

  20. Non-enhanced 3D MR angiography of the lower extremity using ECG-gated TSE imaging with non-selective refocusing pulses. Initial experience

    International Nuclear Information System (INIS)

    Lanzman, R.S.; Blondin, D.; Orzechowski, D.; Scherer, A.; Moedder, U.; Kroepil, P.; Godehardt, E.

    2010-01-01

    Purpose: To evaluate non-enhanced 3D MR angiography using turbo spin echo (TSE) imaging with non-selective refocusing pulses (NATIVE SPACE MRA) for the visualization of the arteries of the lower extremity. Materials and Methods: Three-station imaging (iliac arteries, femoral arteries, arteries of the lower leg) was performed in 8 healthy volunteers and 3 patients with peripheral artery disease (PAD) using a 1.5 T MR scanner. In 8 healthy volunteers, 4 different acquisition schemes were performed with the following imaging parameters: S 1: acquisition with every heartbeat (RR = 1), spoiler gradient of 25 % (SG = 25 %); S 2: RR = 1, SG = 0 %; S 3: RR = 2, SG = 25 %; S 4: RR = 2, SG = 0 %. The subjective image quality on a 4-point-scale (4 = excellent to 1 = not diagnostic) and relative SNR were assessed. In 3 patients with peripheral artery disease (PAD), SPACE MRA was performed for assessment of stenosis. Results: The mean subjective image quality was significantly lower for the iliac arteries compared to the femoral arteries and arteries of the lower leg (p < 0.0001). The subjective image quality for acquisition scheme S 1 was significantly lower than the image quality for S 3 and S 4 for the iliac arteries (p < 0.01), while the subjective image quality for acquisition scheme S 2 was significantly lower than S 3 and S 4 for the femoral arteries and the arteries of the lower leg (p < 0.01). The relative SNR was significantly higher for acquisition schemes S 3 and S 4 as compared to S 1 and S 2 (p < 0.0001) for all regions. SPACE MRA disclosed 7 significant stenoses in 3 PAD patients. Conclusion: ECG-gated SPACE MRA is a promising imaging technique for non-enhanced assessment of the arteries of the lower extremity. (orig.)

  1. Reducing the Risk of Cardiovascular Diseases in Non-selected Outpatients With Schizophrenia: A 30-Month Program Conducted in a Real-life Setting.

    Science.gov (United States)

    Hjorth, Peter; Juel, Anette; Hansen, Mette Vinther; Madsen, Nikolaj Juul; Viuff, Anne Grethe; Munk-Jørgensen, Povl

    2017-12-01

    The most common cause of premature death in people with schizophrenia is cardiovascular disease, partially explained by an unhealthy lifestyle, smoking, poor diet and sedentary behavior. We aimed to reduce cardiovascular risk factors. Naturalistic follow-up study with 54 long-term-treated non-selected outpatients with schizophrenia. The 30-month program consisted of individual guidance, group sessions and normal treatment and care offered in our clinic. On average, the participating women reduced their waist circumference by 11.4cm (P=0.037), whereas the participating men increased their waist circumference by 3.3cm (P=0.590). Patients' consumption of fast food was reduced from 1.2 to 0.8 times/week (P=0.016), just as their consumption of soft drinks was reduced from 0.7 to 0.1l/day (P=0.006). Their consumption of coffee increased from 1.6 to 2.5 cups/day (P=0.086). The time women spent on light physical activity increased from 134 to 469min/week (P=0.055). The number of daily cigarettes smoked was reduced by 25.7% for all smokers. Our program showed that it is possible for women but not for men to reduce their risk factors for developing cardiovascular disease. The program is manageable in most outpatient clinics and can be performed by nursing staff interested in physical health with support from and in cooperation with medical doctors, psychiatrist and leaders/managers. Copyright © 2017 Elsevier Inc. All rights reserved.

  2. MAPLE deposition of nanomaterials

    International Nuclear Information System (INIS)

    Caricato, A.P.; Arima, V.; Catalano, M.; Cesaria, M.; Cozzoli, P.D.; Martino, M.; Taurino, A.; Rella, R.; Scarfiello, R.; Tunno, T.; Zacheo, A.

    2014-01-01

    The matrix-assisted pulsed laser evaporation (MAPLE) has been recently exploited for depositing films of nanomaterials by combining the advantages of colloidal inorganic nanoparticles and laser-based techniques. MAPLE-deposition of nanomaterials meeting applicative purposes demands their peculiar properties to be taken into account while planning depositions to guarantee a congruent transfer (in terms of crystal structure and geometric features) and explain the deposition outcome. In particular, since nanofluids can enhance thermal conductivity with respect to conventional fluids, laser-induced heating can induce different ablation thermal regimes as compared to the MAPLE-treatment of soft materials. Moreover, nanoparticles exhibit lower melting temperatures and can experience pre-melting phenomena as compared to their bulk counterparts, which could easily induce shape and or crystal phase modification of the material to be deposited even at very low fluences. In this complex scenario, this review paper focuses on examples of MAPLE-depositions of size and shape controlled nanoparticles for different applications highlights advantages and challenges of the MAPLE-technique. The influence of the deposition parameters on the physical mechanisms which govern the deposition process is discussed.

  3. MAPLE deposition of nanomaterials

    Energy Technology Data Exchange (ETDEWEB)

    Caricato, A.P., E-mail: annapaola.caricato@le.infn.it [Department of Mathematics and Physics “E. De Giorgi”, University of Salento, Via Arnesano, I-73100 Lecce (Italy); Arima, V.; Catalano, M. [National Nanotechnology Laboratory (NNL), CNR Istituto Nanoscienze, c/o Distretto Tecnologico, Via Arnesano n. 16, I-73100 Lecce (Italy); Cesaria, M. [Department of Mathematics and Physics “E. De Giorgi”, University of Salento, Via Arnesano, I-73100 Lecce (Italy); Cozzoli, P.D. [Department of Mathematics and Physics “E. De Giorgi”, University of Salento, Via Arnesano, I-73100 Lecce (Italy); National Nanotechnology Laboratory (NNL), CNR Istituto Nanoscienze, c/o Distretto Tecnologico, Via Arnesano n. 16, I-73100 Lecce (Italy); Martino, M. [Department of Mathematics and Physics “E. De Giorgi”, University of Salento, Via Arnesano, I-73100 Lecce (Italy); Taurino, A.; Rella, R. [Institute for Microelectronics and Microsystems, IMM-CNR, Via Monteroni, I-73100 Lecce (Italy); Scarfiello, R. [National Nanotechnology Laboratory (NNL), CNR Istituto Nanoscienze, c/o Distretto Tecnologico, Via Arnesano n. 16, I-73100 Lecce (Italy); Tunno, T. [Department of Mathematics and Physics “E. De Giorgi”, University of Salento, Via Arnesano, I-73100 Lecce (Italy); Zacheo, A. [Department of Mathematics and Physics “E. De Giorgi”, University of Salento, Via Arnesano, I-73100 Lecce (Italy); National Nanotechnology Laboratory (NNL), CNR Istituto Nanoscienze, c/o Distretto Tecnologico, Via Arnesano n. 16, I-73100 Lecce (Italy)

    2014-05-01

    The matrix-assisted pulsed laser evaporation (MAPLE) has been recently exploited for depositing films of nanomaterials by combining the advantages of colloidal inorganic nanoparticles and laser-based techniques. MAPLE-deposition of nanomaterials meeting applicative purposes demands their peculiar properties to be taken into account while planning depositions to guarantee a congruent transfer (in terms of crystal structure and geometric features) and explain the deposition outcome. In particular, since nanofluids can enhance thermal conductivity with respect to conventional fluids, laser-induced heating can induce different ablation thermal regimes as compared to the MAPLE-treatment of soft materials. Moreover, nanoparticles exhibit lower melting temperatures and can experience pre-melting phenomena as compared to their bulk counterparts, which could easily induce shape and or crystal phase modification of the material to be deposited even at very low fluences. In this complex scenario, this review paper focuses on examples of MAPLE-depositions of size and shape controlled nanoparticles for different applications highlights advantages and challenges of the MAPLE-technique. The influence of the deposition parameters on the physical mechanisms which govern the deposition process is discussed.

  4. Robust and highly-efficient differentiation of functional monocytic cells from human pluripotent stem cells under serum- and feeder cell-free conditions.

    Directory of Open Access Journals (Sweden)

    Masakatsu D Yanagimachi

    Full Text Available Monocytic lineage cells (monocytes, macrophages and dendritic cells play important roles in immune responses and are involved in various pathological conditions. The development of monocytic cells from human embryonic stem cells (ESCs and induced pluripotent stem cells (iPSCs is of particular interest because it provides an unlimited cell source for clinical application and basic research on disease pathology. Although the methods for monocytic cell differentiation from ESCs/iPSCs using embryonic body or feeder co-culture systems have already been established, these methods depend on the use of xenogeneic materials and, therefore, have a relatively poor-reproducibility. Here, we established a robust and highly-efficient method to differentiate functional monocytic cells from ESCs/iPSCs under serum- and feeder cell-free conditions. This method produced 1.3 × 10(6 ± 0.3 × 10(6 floating monocytes from approximately 30 clusters of ESCs/iPSCs 5-6 times per course of differentiation. Such monocytes could be differentiated into functional macrophages and dendritic cells. This method should be useful for regenerative medicine, disease-specific iPSC studies and drug discovery.

  5. Identification of pectenotoxins in plankton, filter feeders, and isolated cells of a Dinophysis acuminata with an atypical toxin profile, from Chile.

    Science.gov (United States)

    Blanco, Juan; Alvarez, Gonzalo; Uribe, Eduardo

    2007-04-01

    A bloom of Dinophysis acuminata produced, in autumn of 2005, a closure of the scallop harvesting in Bahía Inglesa, in the Chilean III region. Isolated cells of this Dinophysis species were shown to contain 180 pg cell(-1) of pectenotoxin 2 but neither okadaic acid nor any of its analogs or derivatives (at least at a detectable level). Examination of plankton and filter-feeder samples covering an area of ca. 350 km, from the location where the toxicity was recorded to Bahía Tongoy, showed that the unique toxin profile found in the first bloom was widespread over that part of Chile and persisted for months. The analysis were carried out by HPLC-ESI-MS using positive ionization mode, with a detection limit below 2 ng of OA mL(-1) of methanolic extract. This is the first report of the presence of pectenotoxins in the plankton of the Pacific coast of America and in the studied filter feeders. This is also the first report of a Dinophysis species containing pectenotoxins and not any toxin of the okadaic acid group.

  6. Human amniotic epithelial cell feeder layers maintain mouse embryonic stem cell pluripotency via epigenetic regulation of the c-Myc promoter.

    Science.gov (United States)

    Liu, Te; Cheng, Weiwei; Liu, Tianjin; Guo, Lihe; Huang, Qin; Jiang, Lizhen; Du, Xiling; Xu, Fuhui; Liu, Zhixue; Lai, Dongmei

    2010-02-01

    Mouse embryonic stem cells (ESCs) are typically cultured on a feeder layer of mouse embryonic fibroblasts (MEFs), with leukemia inhibitory factor (LIF) added to maintain them in an undifferentiated state. We have previously shown that human amniotic epithelial cells (hAECs) can be used as feeder cells to maintain mouse ESC pluripotency, but the mechanism for this is unknown. In the present study, we found that CpG islands 5' of the c-Myc gene remain hypomethylated in mouse ESCs cultured on hAECs. In addition, levels of acetylation of histone H3 and trimethylation of histone H3K4 in the c-Myc gene promoter were higher in ES cells cultured on hAECs than those in ES cells cultured on MEFs. These data suggested that hAECs can alter mouse ESC gene expression via epigenetic modification of c-Myc, providing a possible mechanism for the hAEC-induced maintenance of ESCs in an undifferentiated state.

  7. Research, Development and Demonstration of Peak Load Reduction on Distribution Feeders Using Distributed Energy Resources for the City of Fort Collins

    Energy Technology Data Exchange (ETDEWEB)

    Sumner, Dennis [City of Fort Collins Utilities, CO (United States); Vosburg, Tom [City of Fort Collins Utilities, CO (United States); Brunner, Steve [Brendle Group, Fort Collins, CO (United States); Gates, Judy [Woodward, Inc., Fort Collins, CO (United States); Howard, Nathan [Spirae, Inc., Fort Collins, CO (United States); Merton, Andrew [Spirae, Inc., Fort Collins, CO (United States); Wright, Don [Spirae, Inc., Fort Collins, CO (United States); Birlingmair, Doug [Spirae, Inc., Fort Collins, CO (United States)

    2015-10-01

    This project titled “Research, Development and Demonstration of Peak Load Reduction on Distribution Feeders Using Distributed Energy Resources for the City of Fort Collins” evolved in response to the Department of Energy’s (DOE) Funding Opportunity Announcement (FOA) Number DE-PS26-07NT43119. Also referred to as the Fort Collins Renewable and Distributed System Integration (RDSI) Project, the effort was undertaken by a diverse group of local government, higher education and business organizations; and was driven by three overarching goals: I. Fulfill the requirements of the DOE FOA’s Area of Interest 2: Renewable and Distributed System Integration; most notably, to demonstrate the ability to reduce electric system distribution feeder peak load by 15% or more through the coordinated use of Distributed Energy Resources (DER). II. Advance the expertise, technologies and infrastructure necessary to support the long term vision of the Fort Collins Zero Energy District (FortZED) and move towards creating a zero energy district in the Fort Collins “Old Town” area. III. Further the goals of the City of Fort Collins Energy Policy, including the development of a Smart Grid-enabled distribution system in Fort Collins, expanded use of renewable energy, increased energy conservation, and peak load reduction. Through the collaborative efforts of the partner organizations, the Fort Collins RDSI project was successful in achieving all three of these goals. This report is organized into two distinct sections corresponding to the two phases of the project: • Part 1: Feeder Peak Load Reduction and the FortZED Initiative. • Part 2: Forming and Operating Utility Microgrids and Managing Load and Production Variability The original project scope addressed the Part 1 feeder peak load reduction. That work took place from 2009 through 2011 and was largely complete when the project scope was amended to include a demonstration of microgrid operations. While leveraging the

  8. Differential effects of selective frankincense (Ru Xiang) essential oil versus non-selective sandalwood (Tan Xiang) essential oil on cultured bladder cancer cells: a microarray and bioinformatics study

    Science.gov (United States)

    2014-01-01

    cancer cell death. While frankincense essential oil elicited selective cancer cell death via NRF-2-mediated oxidative stress, sandalwood essential oil induced non-selective cell death via DNA damage and cell cycle arrest. PMID:25006348

  9. Urban acid deposition

    Energy Technology Data Exchange (ETDEWEB)

    Conlan, D.E.; Longhurst, J.W.S.; Gee, D.R.; Hare, S.E.

    1991-07-01

    In this document results from the Greater Manchester Acid Deposition Survey (GMADS), an urban precipitation chemistry network, for 1990 are presented. Full analytical methods are described along with the precision and accuracy of the methods used. The spatial variability of precipitation chemistry and deposition over this urban region was investigated using a network of twenty collectors. Concentrations of non marine sulphate, ammonium, calcium and hydrogen, and nitrogen dioxide gas concentrations all show significant spatial variability. The spatial variability of the deposition rates of non marine sulphate, nitrate, ammonium, hydrogen and calcium were significant. (Author).

  10. Electroless atomic layer deposition

    Science.gov (United States)

    Robinson, David Bruce; Cappillino, Patrick J.; Sheridan, Leah B.; Stickney, John L.; Benson, David M.

    2017-10-31

    A method of electroless atomic layer deposition is described. The method electrolessly generates a layer of sacrificial material on a surface of a first material. The method adds doses of a solution of a second material to the substrate. The method performs a galvanic exchange reaction to oxidize away the layer of the sacrificial material and deposit a layer of the second material on the surface of the first material. The method can be repeated for a plurality of iterations in order to deposit a desired thickness of the second material on the surface of the first material.

  11. Alluvial Deposits in Iowa

    Data.gov (United States)

    Iowa State University GIS Support and Research Facility — This coverage maps alluvial deposits throughout Iowa. This generally would include areas of alluvial soils associated with modern streams that are identified on...

  12. 75 FR 20041 - Deposits

    Science.gov (United States)

    2010-04-16

    ... transmission to (202) 906- 6518; or send an e-mail to [email protected] . OTS will post... DD implements the Truth in Savings Act, part of the Federal Deposit Insurance Corporation Improvement...

  13. Modeled Wet Nitrate Deposition

    Data.gov (United States)

    U.S. Environmental Protection Agency — Modeled data on nitrate wet deposition was obtained from Dr. Jeff Grimm at Penn State Univ. Nitrate wet depostion causes acidification and eutrophication of surface...

  14. Uranium deposit research, 1983

    International Nuclear Information System (INIS)

    Ruzicka, V.; LeCheminant, G.M.

    1984-01-01

    Research on uranium deposits in Canada, conducted as a prerequisite for assessment of the Estimated Additional Resources of uranium, revealed that (a) the uranium-gold association in rudites of the Huronian Supergroup preferably occurs in the carbon layers; (b) chloritized ore at the Panel mine, Elliot Lake, Ontario, occurs locally in tectonically disturbed areas in the vicinity of diabase dykes; (c) mineralization in the Black Sturgeon Lake area, Ontario, formed from solutions in structural and lithological traps; (d) the Cigar Lake deposit, Saskatchewan, has two phases of mineralization: monomineralic and polymetallic; (e) mineralization of the JEB (Canoxy Ltd.) deposit is similar to that at McClean Lake; (f) the uranium-carbon assemblage was identified in the Claude deposit, Carswell Structure; and (g) the Otish Mountains area, Quebec, should be considered as a significant uranium-polymetallic metallogenic province

  15. Automatic Payroll Deposit System.

    Science.gov (United States)

    Davidson, D. B.

    1979-01-01

    The Automatic Payroll Deposit System in Yakima, Washington's Public School District No. 7, directly transmits each employee's salary amount for each pay period to a bank or other financial institution. (Author/MLF)

  16. Deposition of acidifying compounds

    International Nuclear Information System (INIS)

    Fowler, D.; Cape, J.N.; Sutton, M.A.; Mourne, R.; Hargreaves, K.J.; Duyzer, J.H.; Gallagher, M.W.

    1992-01-01

    Inputs of acidifying compounds to terrestrial ecosystems include deposition of the gases NO 2 , NO, HNO 2 , HNO 3 , NH 3 and SO 2 and the ions NO 3- , NH 4+ , SO 4 2- and H + in precipitation, cloud droplets and particles. Recent research has identified particular ecosystems and regions in which terrestrial effects are closely linked with specific deposition processes. This review paper identifies areas in which important developments have occurred during the last five years and attempts to show which aspects of the subject are most important for policy makers. Amongst the conclusions drawn, the authors advise that current uncertainties in estimates of S and N inputs by dry deposition should be incorporated in critical load calculations, and that, in regions dominated by wet deposition, spatial resolution of total inputs should be improved to match the current scales of information on landscape sensitivity to acidic inputs. 44 refs., 9 figs

  17. Speleothem (Cave Deposit) Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Records of past temperature, precipitation, and other aspects of climate derived from mineral deposits found in caves. Parameter keywords describe what was measured...

  18. Gemstone deposits of Serbia

    Directory of Open Access Journals (Sweden)

    Miladinović Zoran

    2016-06-01

    Full Text Available Gemstone minerals in Serbia have never been regarded as an interesting and significant resource. Nevertheless, more than 150 deposits and occurrences have been recorded and some of them preliminarily explored in the last 50 years. The majority of deposits and occurrences are located within the Serbo-Macedonian metallogenic province and the most significant metallogenic units at the existing level of knowledge are the Fruska Gora ore district, Cer ore district, Sumadija metallogenic zone, Kopaonik metallogenic zone and Lece-Halkidiki metallogenic zone. The most important genetic type of deposits is hydrothermal, particularly in case of serpentinite/peridotite as host/parent rock. Placer deposits are also economically important. The dominant gemstones are silica minerals: chalcedony (Chrysoprase, carnelian, bluish chalcedony etc., jasper (picture, landscape, red etc., common opal (dendritic, green, milky white etc., silica masses (undivided, and quartz (rock crystal, amethyst etc.. Beside silica minerals significant gemstones in Serbia include also beryl (aquamarine, garnet (almandine and pyrope, tourmaline, fluorite, rhodochrosite, carbonate-silica breccia, carbonate-silica onyx, silicified wood, howlite, serpentinite, marble onyx, and kyanite. This paper aims to present an overview of Serbian gemstone deposits and occurrences and their position based on a simplified gemstone metallogenic map of Serbia, as well as genetic-industrial classification of gemstone deposits and gemstone varieties.

  19. Uranium deposits in Africa

    International Nuclear Information System (INIS)

    Wilpolt, R.H.; Simov, S.D.

    1979-01-01

    Africa is not only known for its spectacular diamond, gold, copper, chromium, platinum and phosphorus deposits but also for its uranium deposits. At least two uranium provinces can be distinguished - the southern, with the equatorial sub-province; and the south Saharan province. Uranium deposits are distributed either in cratons or in mobile belts, the first of sandstone and quartz-pebble conglomerate type, while those located in mobile belts are predominantly of vein and similar (disseminated) type. Uranium deposits occur within Precambrian rocks or in younger platform sediments, but close to the exposed Precambrian basement. The Proterozoic host rocks consist of sediments, metamorphics or granitoids. In contrast to Phanerozoic continental uranium-bearing sediments, those in the Precambrian are in marginal marine facies but they do contain organic material. The geology of Africa is briefly reviewed with the emphasis on those features which might control the distribution of uranium. The evolution of the African Platform is considered as a progressive reduction of its craton area which has been affected by three major Precambrian tectonic events. A short survey on the geology of known uranium deposits is made. However, some deposits and occurrences for which little published material is available are treated in more detail. (author)

  20. Gemstone deposits of Serbia

    Science.gov (United States)

    Miladinović, Zoran; Simić, Vladimir; Jelenković, Rade; Ilić, Miloje

    2016-06-01

    Gemstone minerals in Serbia have never been regarded as an interesting and significant resource. Nevertheless, more than 150 deposits and occurrences have been recorded and some of them preliminarily explored in the last 50 years. The majority of deposits and occurrences are located within the Serbo-Macedonian metallogenic province and the most significant metallogenic units at the existing level of knowledge are the Fruska Gora ore district, Cer ore district, Sumadija metallogenic zone, Kopaonik metallogenic zone and Lece-Halkidiki metallogenic zone. The most important genetic type of deposits is hydrothermal, particularly in case of serpentinite/peridotite as host/parent rock. Placer deposits are also economically important. The dominant gemstones are silica minerals: chalcedony (Chrysoprase, carnelian, bluish chalcedony etc.), jasper (picture, landscape, red etc.), common opal (dendritic, green, milky white etc.), silica masses (undivided), and quartz (rock crystal, amethyst etc.). Beside silica minerals significant gemstones in Serbia include also beryl (aquamarine), garnet (almandine and pyrope), tourmaline, fluorite, rhodochrosite, carbonate-silica breccia, carbonate-silica onyx, silicified wood, howlite, serpentinite, marble onyx, and kyanite. This paper aims to present an overview of Serbian gemstone deposits and occurrences and their position based on a simplified gemstone metallogenic map of Serbia, as well as genetic-industrial classification of gemstone deposits and gemstone varieties.

  1. A feeder- and xeno-free human induced pluripotent stem cell line obtained from primary human dermal fibroblasts with epigenetic repression of reprogramming factors expression: GPCCi001-A

    Directory of Open Access Journals (Sweden)

    Michał Stefan Lach

    2017-04-01

    Full Text Available The primary human dermal fibroblasts (PHDFs from breast cancer patient were obtained to generate the human induced pluripotent stem cell line GPCCi001-A via lentiviral transfection. Thus, a modified EF1a-hSTEMCCA-loxP with tetO operator which regulates transgene expression was used. This method takes advantage of epigenetic regulation of transcription and allows for stable silencing of the reprogramming factors in obtained hiPS cells. To increase the potential utility of hiPSCs for clinical applications, they were adapted to feeder- and xeno-free conditions. The pluripotency of GPCCi001-A cell line and ability to differentiate into three germ layers was confirmed.

  2. A defined, feeder-free, serum-free system to generate in vitro hematopoietic progenitors and differentiated blood cells from hESCs and hiPSCs.

    Directory of Open Access Journals (Sweden)

    Giorgia Salvagiotto

    2011-03-01

    Full Text Available Human ESC and iPSC are an attractive source of cells of high quantity and purity to be used to elucidate early human development processes, for drug discovery, and in clinical cell therapy applications. To efficiently differentiate pluripotent cells into a pure population of hematopoietic progenitors we have developed a new 2-dimensional, defined and highly efficient protocol that avoids the use of feeder cells, serum or embryoid body formation. Here we showed that a single matrix protein in combination with growth factors and a hypoxic environment is sufficient to generate from pluripotent cells hematopoietic progenitors capable of differentiating further in mature cell types of different lineages of the blood system. We tested the differentiation method using hESCs and 9 iPSC lines generated from different tissues. These data indicate the robustness of the protocol providing a valuable tool for the generation of clinical-grade hematopoietic cells from pluripotent cells.

  3. Comparative bioaccumulation of trace metals using six filter feeder organisms in a coastal lagoon ecosystem (of the central-east Gulf of California).

    Science.gov (United States)

    Jara-Marini, M E; Tapia-Alcaraz, J N; Dumer-Gutiérrez, J A; García-Rico, L; García-Hernández, J; Páez-Osuna, F

    2013-02-01

    The Tobari Lagoon, located in the central-east coast of the Gulf of California, receives effluents from the Yaqui Valley, one of the most extensive agricultural areas of México. The Tobari Lagoon also receives effluents from nearby shrimp farms and untreated municipal sewage. Surface sediment samples and six different species of filter feeders (Crassostrea corteziensis, Crassostrea gigas, Chione gnidia, Anadara tuberculosa, Chione fluctifraga, and Fistulobalanus dentivarians) were collected during the dry and the rainy seasons and analyzed to determine concentrations of cadmium (Cd), copper (Cu), mercury (Hg), lead (Pb), and zinc (Zn). Seasonal variations in metal concentrations in sediment were evident, especially for Cd, Cu, Hg, and Zn. The total and bioavailable concentrations of the five metals are not elevated in comparison to other areas around the world. The percentages of bioavailable respect to total concentrations of the metals varied from 0.6 % in Hg to 50.2 % for Cu. In the organisms, Hg showed the lowest concentrations (ranged from 0.22 to 0.65 μg/g) while Zn showed the highest (ranged from 36.6 to 1,702 μg/g). Linear correlations between the levels of Cu, Pb, and Zn in the soft tissues of C. fluctifraga and C. gnidia, and A. tuberculosa and C. gnidia were found. Seasonal and interspecies variations in the metal levels in filter feeders were found; F. dentivarians, C. corteziensis, and C. gigas exhibited the highest levels, could be used as biomonitors of metals contamination in this area.

  4. Easy xeno-free and feeder-free method for isolating and growing limbal stromal and epithelial stem cells of the human cornea.

    Directory of Open Access Journals (Sweden)

    Djida Ghoubay-Benallaoua

    Full Text Available Epithelial and stromal stem cells are required to maintain corneal transparency. The aim of the study was to develop a new method to isolate and grow both corneal stromal (SSC and epithelial limbal (LSC stem cells from small human limbal biopsies under culture conditions in accordance with safety requirements mandatory for clinical use in humans. Superficial limbal explants were retrieved from human donor corneo-scleral rims. Human limbal cells were dissociated by digestion with collagenase A, either after epithelial scraping or with no scraping. Isolated cells were cultured with Essential 8 medium (E8, E8 supplemented with EGF (E8+ or Green's medium with 3T3 feeder-layers. Cells were characterized by immunostaining, RT-qPCR, colony forming efficiency, sphere formation, population doubling, second harmonic generation microscopy and differentiation potentials. LSC were obtained from unscraped explants in E8, E8+ and Green's media and were characterized by colony formation and expression of PAX6, ΔNP63α, Bmi1, ABCG2, SOX9, CK14, CK15 and vimentin, with a few cells positive for CK3. LSC underwent 28 population doublings still forming colonies. SSC were obtained from both scraped and unscraped explants in E8 and E8+ media and were characterized by sphere formation, expression of PAX6, SOX2, BMI1, NESTIN, ABCG2, KERATOCAN, VIMENTIN, SOX9, SOX10 and HNK1, production of collagen fibrils and differentiation into keratocytes, fibroblasts, myofibroblasts, neurons, adipocytes, chondrocytes and osteocytes. SSC underwent 48 population doublings still forming spheres, Thus, this new method allows both SSC and LSC to be isolated from small superficial limbal biopsies and to be primary cultured in feeder-free and xeno-free conditions, which will be useful for clinical purposes.

  5. Comparison of the Ex Vivo Expansion of UCB-Derived CD34+ in 3D DBM/MBA Scaffolds with USSC as a Feeder Layer.

    Science.gov (United States)

    Sadat Hashemi, Zahra; Forouzandeh Moghadam, Mahdi; Soleimani, Masoud

    2013-10-01

    Ex vivo expansion of hematopoitic stem cells is an alternative way to increase umbilical cord blood (UCB)-CD34+ cells for bone marrow transplantation. For this purpose demineralized bone matrix (DBM) and mineralized bone allograft (MBA) as two scaffolds based on bone matrix and stem cell niche, were simultaneously used to enhance the effect of human mesenchymal progenitor cells (MPCs) - unrestricted somatic stem cells (USSCs) - as a feeder layer. USSCs were isolated and characterized by morphological and immunological analysis then seeded on both scaffolds as a feeder layer. UCB-CD34(+) were isolated by MACS method and were co-culture expanded by USSC in 3D and 2D environments. After 3 weeks expansion, cells were counted and were assessed by karyotype, flow cytometry, clonogenic activity, and long-term culture-initiating cells (LTC-IC). Co-culture expansion in DBM and MBA was 29.22-fold and 27.77-fold, no significant differences in colony and LTC-IC were obtained. Maximum number of colonies belonged to the day 14 with the 73% CFU-GM (Colony Forming Unit- Granulocyte/Macrophage) in contrast to the day 0 which was BFU-E/CFU-E (Burst/Colony Forming Unit-Erythroid). Flow cytometry indicated that the percentage of CD34+ marker was decreased in USSC co-culture and the highest percentage was observed in simple 2D culture. Because of acid extraction in the DBM production process, mineral materials were removed and the protein background that was more flexible was presented. Therefore these results suggest that USSC-DBM can be a suitable ex vivo mimicry niche by intensifying of surface/volume ratio and supporting the stem cell differentiation and expansion.

  6. 47 CFR 25.250 - Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands. 25.250 Section 25.250 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Technical Standards § 25...

  7. Practice on Protection and Improvement of Withstand Voltage Weighing Belt Coal Feeder%耐压称重式皮带给煤机保护改进实践

    Institute of Scientific and Technical Information of China (English)

    王良

    2016-01-01

    This paper introduces the traits of withstand voltage weighing belt coal feeder. According to the modification and practice of parameters of the frequency converter, when there is a malfunction, the automatic recovery of the frequency converter of coal feeder can be achieved. The reliability of the coal feeder ’s operation will be improved, and the effects of the accident power supply perturbation on the coal feeder can be eliminated. Eventually, the safety and stability of the boilers can be guaranteed.%文章介绍了耐压称重式皮带给煤机的特性,通过对变频器参数修改实践,实现给煤机变频器故障保护自动恢复,提高给煤机运行的可靠性,消除电源意外扰动对给煤机的影响,保障锅炉安全持续稳定运行。

  8. Comparison between paricalcitol and active non-selective vitamin D receptor activator for secondary hyperparathyroidism in chronic kidney disease: a systematic review and meta-analysis of randomized controlled trials.

    Science.gov (United States)

    Cai, Panpan; Tang, Xiaohong; Qin, Wei; Ji, Ling; Li, Zi

    2016-04-01

    The goal of this systematic review is to evaluate the efficacy and safety of paricalcitol versus active non-selective vitamin D receptor activators (VDRAs) for secondary hyperparathyroidism (SHPT) management in chronic kidney disease (CKD) patients. PubMed, EMBASE, Cochrane Central Register of Controlled Trials (CENTRAL), clinicaltrials.gov (inception to September 2015), and ASN Web site were searched for relevant studies. A meta-analysis of randomized controlled trials (RCTs) and quasi-RCTs that assessed the effects and adverse events of paricalcitol and active non-selective VDRA in adult CKD patients with SHPT was performed using Review Manager 5.2. A total of 10 trials involving 734 patients were identified for this review. The quality of included trials was limited, and very few trials reported all-cause mortality or cardiovascular calcification without any differences between two groups. Compared with active non-selective VDRAs, paricalcitol showed no significant difference in both PTH reduction (MD -7.78, 95% CI -28.59-13.03, P = 0.46) and the proportion of patients who achieved the target reduction of PTH (OR 1.27, 95% CI 0.87-1.85, P = 0.22). In addition, no statistical differences were found in terms of serum calcium, episodes of hypercalcemia, serum phosphorus, calcium × phosphorus products, and bone metabolism index. Current evidence is insufficient, showing paricalcitol is superior to active non-selective VDRAs in lowering PTH or reducing the burden of mineral loading. Further trials are required to prove the tissue-selective effect of paricalcitol and to overcome the limitation of current research.

  9. Vein type uranium deposits

    International Nuclear Information System (INIS)

    1986-01-01

    Veins are tabular- or sheet-like masses of minerals occupying or following a fracture or a set of fractures in the enclosing rock. They have been formed later than the country rock and fractures, either by filling of the open spaces or by partial or complete replacement of the adjoining rock or most commonly by both of these processes combined. This volume begins with the occurrences and deposits known from old shield areas and the sedimentary belts surrounding them. They are followed by papers describing the European deposits mostly of Variscan age, and by similar deposits known from China being of Jurassic age. The volume is completed by two papers which do not fit exactly in the given scheme. A separate abstract was prepared for each of the 25 papers in this report

  10. Optical thin film deposition

    International Nuclear Information System (INIS)

    Macleod, H.A.

    1979-01-01

    The potential usefulness in the production of optical thin-film coatings of some of the processes for thin film deposition which can be classified under the heading of ion-assisted techniques is examined. Thermal evaporation is the process which is virtually universally used for this purpose and which has been developed to a stage where performance is in almost all respects high. Areas where further improvements would be of value, and the possibility that ion-assisted deposition might lead to such improvements, are discussed. (author)

  11. Radionuclide deposition control

    International Nuclear Information System (INIS)

    1980-01-01

    A method is described for controlling the deposition, on to the surfaces of reactor components, of the radionuclides manganese-54, cobalt-58 and cobalt-60 from a liquid stream containing the radionuclides. The method consists of disposing a getter material (nickel) in the liquid stream, and a non-getter material (tantalum, tungsten or molybdenum) as a coating on the surfaces where deposition is not desired. The process is described with special reference to its use in the coolant circuit in sodium cooled fast breeder reactors. (U.K.)

  12. Deposition potential of polonium

    Energy Technology Data Exchange (ETDEWEB)

    Heal, H. G.

    1948-11-23

    The cathodic deposition potential for polonium in concentrations of 10{sup -13} normal and 8 x 10{sup -13} normal, the former being 100-fold smaller than the smallest concentrations previously studied, has been determined. The value is 0.64 volt on the hydrogen scale. Considering the various ways in which the graphs can reasonably be drawn, we consider the maximum possible error to be of the order of +- 0.03 volt. There is apparently no shift of deposition potential between concentrations of 10{sup -8} and 10{sup -13} normal, indicating that the Nernst equation is not applicable in these circumstances.

  13. Reactive polymer fused deposition manufacturing

    Science.gov (United States)

    Kunc, Vlastimil; Rios, Orlando; Love, Lonnie J.; Duty, Chad E.; Johs, Alexander

    2017-05-16

    Methods and compositions for additive manufacturing that include reactive or thermosetting polymers, such as urethanes and epoxies. The polymers are melted, partially cross-linked prior to the depositing, deposited to form a component object, solidified, and fully cross-linked. These polymers form networks of chemical bonds that span the deposited layers. Application of a directional electromagnetic field can be applied to aromatic polymers after deposition to align the polymers for improved bonding between the deposited layers.

  14. Deposition of porous cathodes using plasma spray technique for reduced-temperature SOFCs

    Energy Technology Data Exchange (ETDEWEB)

    Jankovic, J.; Hui, S.; Roller, J.; Kesler, O.; Xie, Y.; Maric, R.; Ghosh, D. [National Research Council of Canada, Vancouver, BC (Canada). Inst. for Fuel Cell Innovation

    2005-07-01

    Current techniques for Solid Oxide Fuel Cell (SOFC) materials deposition are often expensive and time-consuming. Plasma-spraying techniques provide higher deposition rates, short processing times and control over porosity and composition during deposition. Optimum plasma spraying for lanthanum based cathode materials were discussed. Plasma-spraying was used to deposit cathode materials onto ceramic and stainless steel substrates to obtain highly porous structures. Lanthanum cathode materials with composition of La{sub 0.6}Sr{sub 0.4}C{sub 0.2}Fe{sub 0.8}O{sub 3} were employed in the powder form. The powder was prepared from powder precursors with different power formers and binder levels, or from produced single-phase lanthanum powders. The (La{sub 0.8}Sr{sub 0.2}){sub 0.98}MnO{sub 3} cathode material was also processed for comparison purposes. The deposition process was developed to obtain coatings with good bond strength, porosity, film thickness and residual stresses. The phase and microstructure of deposited materials were characterized using X-Ray Diffraction and Scanning Electron Microscopy (SEM). It was concluded that good flow of the powder precursors is achieved by spraying 50-100 um particle size powders and using vibrating feeders. Further processing of the spraying powders was recommended. It was noted that oxide precursors showed greater reactivity among the precursors. The best precursor reactivity and coating morphology was obtained using 40 volume per cent of graphite pore former, incorporated into the precursor mixture during wet ball milling. It was concluded that higher power levels and larger distances between the plasma gun and the substrate result in coatings with the highest porosities and best phase compositions. 5 refs., 1 tab., 6 figs.

  15. Ion Deposited Carbon Coatings.

    Science.gov (United States)

    1983-07-01

    PAGE ("’hen Dita t,,I,, efl TABLE OF CONTENTS Section No. Title Page No. 1.0 OBJECTIVE 1 2.0 SCOPE 2 3.0 BACKGROUND 3 4.0 COATINGS DEPOSITION 4 4.1...scientific, ards of measure. The Committee, and Confer- technical, practical, and teaching purposes.ence voting members, are leading professional On the

  16. Plasma deposition of refractories

    International Nuclear Information System (INIS)

    Kudinov, V.V.; Ivanov, V.M.

    1981-01-01

    The problems of deposition, testing and application of plasma coating of refractory metals and oxides are considered. The process fundamentals, various manufacturing procedures and equipment for their realization are described in detail. Coating materials are given (Al, Mg, Al 2 O 3 , ZrO 2 , MgAlO 4 ) which are used in reactor engineering and their designated purposes are shown [ru

  17. 75 FR 34533 - Deposits

    Science.gov (United States)

    2010-06-17

    ... collection request (ICR) described below has been submitted to the Office of Management and Budget (OMB) for..., Attention: Desk Officer for OTS, U.S. Office of Management and Budget, 725 17th Street, NW., Room 10235... statement the institution sends to the consumer. Regulation DD contains rules for advertisements of deposit...

  18. The first pterosaur 3-D egg: Implications for Pterodaustro guinazui nesting strategies, an Albian filter feeder pterosaur from central Argentina

    Directory of Open Access Journals (Sweden)

    Gerald Grellet-Tinner

    2014-11-01

    Full Text Available The increasing number of fossil pterosaur eggs sheds light on nesting environments and breeding behaviors of these extinct flying reptiles. Here we report the first partial three-dimensional egg of the pterosaur, Pterodaustro guinazui, from central Argentina. The specimen was discovered from the same Albian deposits as the exceptional P. guinazui embryo described in 2004. Microscopic characterizations indicate a pristine preservation of the 50 μm thick calcium carbonate, which differs significantly from the soft shell of Chinese pterosaur eggs. Estimate of the eggshell conductance implies that the nest had a minimum moisture content of 75%. This moisture estimate, combined with geological and taphonomical data, suggests that P. guinazui may have adopted a nesting strategy similar to those of grebes and flamingos rather than being buried on land, as previously hypothesized. Moreover, our results demonstrate that the nesting paleoenvironment of this pterosaur species was closely linked to a mesohaline lacustrine ecosystem in a basin governed by regional tectonic subsidence, a setting characteristic for the feeding and reproduction of modern flamingos.

  19. Critical evaluation of gamma-irradiated serum used as feeder in the culture and demonstration of putative nanobacteria and calcifying nanoparticles.

    Directory of Open Access Journals (Sweden)

    Jan Martel

    used as feeder. Thus, the NB/CNP described in the literature clearly bear hybrid protein compositions belonging to different species. We conclude that there is no basis to justify the use of gamma-FBS as a feeder for the growth and demonstration of NB/CNP or any NB-like particles in culture. Moreover, our results call into question the validity of the entire body of literature accumulated to date on NB and CNP.

  20. Effects of temperament and acclimation to handling on feedlot performance of Bos taurus feeder cattle originated from a rangeland-based cow-calf system.

    Science.gov (United States)

    Francisco, C L; Cooke, R F; Marques, R S; Mills, R R; Bohnert, D W

    2012-12-01

    Two experiments evaluated the effects of temperament and acclimation to handling on performance of Angus × Hereford feeder cattle reared in extensive rangeland systems until weaning. In Exp. 1, 200 calves (n = 97 for yr 1; n = 103 for yr 2) were evaluated for temperament at weaning (average age ± SE = 152 ± 1 d) by chute score and exit velocity. Chute score was assessed on a 5-point scale according to behavior during chute restraining. Exit score was calculated by dividing exit velocity into quintiles and assigning calves a score from 1 (slowest) to 5 (fastest). A temperament score was calculated for each calf by averaging chute and exit scores. Calf temperament was classified according to temperament score as adequate (≤3) or excitable (>3). After weaning, calves were assigned to a 40-d preconditioning followed by growing (139 d) and finishing (117 d) phases until slaughter. Weaning BW was decreased (P = 0.04) in excitable calves compared with adequate calves. No differences were detected (P ≥ 0.21) for ADG during preconditioning, growing, and finishing phases; hence, excitable calves tended (P = 0.09) to have decreased HCW compared with adequate calves. In Exp. 2, 60 steers (initial age ± SE = 198 ± 2 d) were weighed and evaluated for temperament score 35 d after weaning (d -29). On d -28, steers were ranked by these variables and assigned to receive an acclimation treatment or not (control). Acclimated steers were processed through a handling facility twice weekly for 4 wk (d -28 to -1) whereas control steers remained undisturbed on pasture. On d 0, all steers were transported for 24 h and returned to the research facility (d 1). On arrival, steers were ranked by BW within treatment and randomly assigned to 20 feedlot pens for a 28-d feedlot receiving period. Acclimated steers had decreased temperament score and plasma cortisol compared with controls on d 0 (P = 0.02). During feedlot receiving, acclimated steers had decreased ADG (P < 0.01) and G:F (P

  1. 78 FR 56583 - Deposit Insurance Regulations; Definition of Insured Deposit

    Science.gov (United States)

    2013-09-13

    ... as a potential global deposit insurer, preserve confidence in the FDIC deposit insurance system, and... the United States.\\2\\ The FDIC generally pays out deposit insurance on the next business day after a... since 2001 and total approximately $1 trillion today. In many cases, these branches do not engage in...

  2. Uranium deposits of Zaire

    International Nuclear Information System (INIS)

    Kitmut, D.; Malu wa Kalenga

    1979-01-01

    Since April 1960, following the closing of the Shinkolobwe mine, the Republic of Zaire has ceased to be a producer of uranium. Nevertheless, Gecamines (Generale des carrieres et mines du Zaire), a wholly state-owned company, is continuing its research on uranium occurrences which have been discovered in its concession in the course of aerial radiometric prospecting. The most recent campaign was the one carried out in 1969 and 1972 by Hunting Company. On-the-ground verification of these shows has not yet resulted in the discovery of a workable deposit. There are other sectors cutting across Zaire which might well contain uranium deposits: this is true of the sedimentary phosphates of the region of Lower Zaire as well as of the frontier region between Zaire and the Central African Empire. However, no detailed exploration work has yet been carried out. (author)

  3. 20 CFR 703.306 - Kinds of negotiable securities that may be deposited; conditions of deposit; acceptance of deposits.

    Science.gov (United States)

    2010-04-01

    ... the Act in the amount fixed by the Office under the regulations in this part shall deposit any... deposited; conditions of deposit; acceptance of deposits. 703.306 Section 703.306 Employees' Benefits... negotiable securities that may be deposited; conditions of deposit; acceptance of deposits. A self-insurer or...

  4. Thorium ore deposits

    International Nuclear Information System (INIS)

    Angelelli, Victorio.

    1984-01-01

    The main occurences of the thorium minerals of the Argentine Republic which have not been exploited, due to their reduced volume, are described. The thoriferous deposits have three genetic types: pegmatitic, hydrothermal and detritic, being the most common minerals: monazite, thorite and thorogummite. The most important thorium accumulations are located in Salta, being of less importance those of Cordoba, Jujuy and San Juan. (M.E.L.) [es

  5. Electrophoretic deposition of biomaterials

    Science.gov (United States)

    Boccaccini, A. R.; Keim, S.; Ma, R.; Li, Y.; Zhitomirsky, I.

    2010-01-01

    Electrophoretic deposition (EPD) is attracting increasing attention as an effective technique for the processing of biomaterials, specifically bioactive coatings and biomedical nanostructures. The well-known advantages of EPD for the production of a wide range of microstructures and nanostructures as well as unique and complex material combinations are being exploited, starting from well-dispersed suspensions of biomaterials in particulate form (microsized and nanoscale particles, nanotubes, nanoplatelets). EPD of biological entities such as enzymes, bacteria and cells is also being investigated. The review presents a comprehensive summary and discussion of relevant recent work on EPD describing the specific application of the technique in the processing of several biomaterials, focusing on (i) conventional bioactive (inorganic) coatings, e.g. hydroxyapatite or bioactive glass coatings on orthopaedic implants, and (ii) biomedical nanostructures, including biopolymer–ceramic nanocomposites, carbon nanotube coatings, tissue engineering scaffolds, deposition of proteins and other biological entities for sensors and advanced functional coatings. It is the intention to inform the reader on how EPD has become an important tool in advanced biomaterials processing, as a convenient alternative to conventional methods, and to present the potential of the technique to manipulate and control the deposition of a range of nanomaterials of interest in the biomedical and biotechnology fields. PMID:20504802

  6. Radionuclides deposition over Antarctica

    International Nuclear Information System (INIS)

    Pourchet, M.; Magand, O.; Frezzotti, M.; Ekaykin, A.; Winther, J.-G.

    2003-01-01

    A detailed and comprehensive map of the distribution patterns for both natural and artificial radionuclides over Antarctica has been established. This work integrates the results of several decades of international programs focusing on the analysis of natural and artificial radionuclides in snow and ice cores from this polar region. The mean value (37±20 Bq m -2 ) of 241 Pu total deposition over 28 stations is determined from the gamma emissions of its daughter 241 Am, presenting a long half-life (432.7 yrs). Detailed profiles and distributions of 241 Pu in ice cores make it possible to clearly distinguish between the atmospheric thermonuclear tests of the fifties and sixties. Strong relationships are also found between radionuclide data ( 137 Cs with respect to 241 Pu and 210 Pb with respect to 137 Cs), make it possible to estimate the total deposition or natural fluxes of these radionuclides. Total deposition of 137 Cs over Antarctica is estimated at 760 TBq, based on results from the 90-180 deg. East sector. Given the irregular distribution of sampling sites, more ice cores and snow samples must be analyzed in other sectors of Antarctica to check the validity of this figure

  7. Deposition and Resuspension of Particles

    DEFF Research Database (Denmark)

    Lengweiler, P.; Nielsen, Peter V.; Moser, A.

    A new experimental set-up to investigate the physical process of dust deposition and resuspension on and from surfaces is introduced. Dust deposition can reduce the airBorne dust concentration considerably. As a basis for developing methods to eliminate dust related problems in rooms......, there is a need for better understanding of the mechanism of dust deposition and resuspension....

  8. A Micrometeorological Perspective on Deposition

    DEFF Research Database (Denmark)

    Jensen, Niels Otto

    1981-01-01

    An expression for the dry deposition velocity is given in terms of constant flux layer scaling. Numerical values of upper bounds on the deposition velocity is given for a typical situation. Some remarks are then offered on the relative merits of various ways in which the combined diffusion-deposition...

  9. Market Discipline and Deposit Insurance

    OpenAIRE

    Peresetsky, Anatoly

    2008-01-01

    The paper examines Russian banks’ household deposit interest rates for the transition period of setting up the deposit insurance system. Monthly observations of Russian banks’ interest rates and balance sheets are used in a fixed effects panel data model. It is shown market discipline has been significantly diminished after switching to the deposit insurance.

  10. Electrophoretic Deposition of Gallium with High Deposition Rate

    Directory of Open Access Journals (Sweden)

    Hanfei Zhang

    2014-12-01

    Full Text Available In this work, electrophoretic deposition (EPD is reported to form gallium thin film with high deposition rate and low cost while avoiding the highly toxic chemicals typically used in electroplating. A maximum deposition rate of ~0.6 μm/min, almost one order of magnitude higher than the typical value reported for electroplating, is obtained when employing a set of proper deposition parameters. The thickness of the film is shown to increase with deposition time when sequential deposition is employed. The concentration of Mg(NO32, the charging salt, is also found to be a critical factor to control the deposition rate. Various gallium micropatterns are obtained by masking the substrate during the process, demonstrating process compatibility with microfabrication. The reported novel approach can potentially be employed in a broad range of applications with Ga as a raw material, including microelectronics, photovoltaic cells, and flexible liquid metal microelectrodes.

  11. Feeder and post Deccan Trap dyke activities in the northern slope of the Satpura Mountain: Evidence from new 40Ar-39Ar ages

    Directory of Open Access Journals (Sweden)

    J.P. Shrivastava

    2017-05-01

    Full Text Available We present new 40Ar-39Ar plagioclase crystallization ages from the dykes exposed at the northern slope of the Satpura Mountain range near Betul-Jabalpur-Pachmarhi area, ∼800 km NE of the Western Ghats escarpment. Among the two plateau ages, the first age of 66.56 ± 0.42 Ma from a dyke near Mohpani village represents its crystallization age which is either slightly older or contemporaneous with the nearby Mandla lava flows (63–65 Ma. We suggest that the Mohpani dyke might be one of the feeders for the surrounding lava flows as these lavas are significantly younger than the majority of the main Deccan lavas of the Western Ghats (66.38–65.54 Ma. The second age of 56.95 ± 1.08 Ma comes from a younger dyke near Olini village which cuts across the lava flows of the area. The age correlates well with the Mandla lavas which are chemically similar to the uppermost Poladpur, Ambenali and Mahabaleshwar Formation lavas of SW Deccan. Our study shows that the dyke activities occurred in two phases, with the second one representing the terminal stage.

  12. Feeder Voltage Regulation with High-Penetration PV Using Advanced Inverters and a Distribution Management System: A Duke Energy Case Study

    Energy Technology Data Exchange (ETDEWEB)

    Palmintier, Bryan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Giraldez, Julieta [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gruchalla, Kenny [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gotseff, Peter [National Renewable Energy Lab. (NREL), Golden, CO (United States); Nagarajan, Adarsh [National Renewable Energy Lab. (NREL), Golden, CO (United States); Harris, Tom [National Renewable Energy Lab. (NREL), Golden, CO (United States); Bugbee, Bruce [National Renewable Energy Lab. (NREL), Golden, CO (United States); Baggu, Murali [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gantz, Jesse [GE Grid Solutions, Fairfield, CT (United States); Boardman, Ethan [GE Grid Solutions, Fairfield, CT (United States)

    2016-11-01

    Duke Energy, Alstom Grid, and the National Renewable Energy Laboratory teamed up to better understand the impacts of solar photovoltaics (PV) on distribution system operations. The core goal of the project is to compare the operational - specifically, voltage regulation - impacts of three classes of PV inverter operations: 1.) Active power only (Baseline); 2.) Local inverter control (e.g., PF...not equal...1, Q(V), etc.); and 3.) Integrated volt-VAR control (centralized through the distribution management system). These comparisons were made using multiple approaches, each of which represents an important research-and-development effort on its own: a) Quasi-steady-state time-series modeling for approximately 1 year of operations using the Alstom eTerra (DOTS) system as a simulation engine, augmented by Python scripting for scenario and time-series control and using external models for an advanced inverter; b) Power-hardware-in-the-loop (PHIL) testing of a 500-kVA-class advanced inverter and traditional voltage regulating equipment. This PHIL testing used cosimulation to link full-scale feeder simulation using DOTS in real time to hardware testing; c) Advanced visualization to provide improved insights into time-series results and other PV operational impacts; and d) Cost-benefit analysis to compare the financial and business-model impacts of each integration approach.

  13. Stepwise Differentiation of Pluripotent Stem Cells into Osteoblasts Using Four Small Molecules under Serum-free and Feeder-free Conditions

    Directory of Open Access Journals (Sweden)

    Kosuke Kanke

    2014-06-01

    Full Text Available Pluripotent stem cells are a promising tool for mechanistic studies of tissue development, drug screening, and cell-based therapies. Here, we report an effective and mass-producing strategy for the stepwise differentiation of mouse embryonic stem cells (mESCs and mouse and human induced pluripotent stem cells (miPSCs and hiPSCs, respectively into osteoblasts using four small molecules (CHIR99021 [CHIR], cyclopamine [Cyc], smoothened agonist [SAG], and a helioxanthin-derivative 4-(4-methoxyphenylpyrido[4′,3′:4,5]thieno[2,3-b]pyridine-2-carboxamide [TH] under serum-free and feeder-free conditions. The strategy, which consists of mesoderm induction, osteoblast induction, and osteoblast maturation phases, significantly induced expressions of osteoblast-related genes and proteins in mESCs, miPSCs, and hiPSCs. In addition, when mESCs defective in runt-related transcription factor 2 (Runx2, a master regulator of osteogenesis, were cultured by the strategy, they molecularly recapitulated osteoblast phenotypes of Runx2 null mice. The present strategy will be a platform for biological and pathological studies of osteoblast development, screening of bone-augmentation drugs, and skeletal regeneration.

  14. Efficient generation of transgene- and feeder-free induced pluripotent stem cells from human dental mesenchymal stem cells and their chemically defined differentiation into cardiomyocytes.

    Science.gov (United States)

    Tan, Xiaobing; Dai, Qingli; Guo, Tao; Xu, Jingshu; Dai, Qingyuan

    2018-01-22

    Advance in stem cell research resulted in several processes to generate induced pluripotent stem cells (iPSCs) from adult somatic cells. In our previous study, the reprogramming of iPSCs from human dental mesenchymal stem cells (MSCs) including SCAP and DPSCs, has been reported. Herein, safe iPSCs were reprogrammed from SCAP and DPSCs using non-integrating RNA virus vector, which is an RNA virus carrying no risk of altering host genome. DPSCs- and SCAP-derived iPSCs exhibited the characteristics of the classical morphology with human embryonic stem cells (hESCs) without integration of foreign genes, indicating the potential of their clinical application. Moreover, induced PSCs showed the capacity of self-renewal and differentiation into cardiac myocytes. We have achieved the differentiation of hiPSCs to cardiomyocytes lineage under serum and feeder-free conditions, using a chemically defined medium CDM3. In CDM3, hiPSCs differentiation is highly generating cardiomyocytes. The results showed this protocol produced contractile sheets of up to 97.2% TNNT2 cardiomyocytes after purification. Furthermore, derived hiPSCs differentiated to mature cells of the three embryonic germ layers in vivo and in vitro of beating cardiomyocytes. The above whole protocol enables the generation of large scale of highly pure cardiomyocytes as needed for cellular therapy. Copyright © 2017. Published by Elsevier Inc.

  15. Induced pluripotent stem cells generated from human adipose-derived stem cells using a non-viral polycistronic plasmid in feeder-free conditions.

    Directory of Open Access Journals (Sweden)

    Xinjian Qu

    Full Text Available Induced pluripotent stem cells (iPSCs can be generated from somatic cells by ectopic expression of defined transcription factors (TFs. However, the optimal cell type and the easy reprogramming approaches that minimize genetic aberrations of parent cells must be considered before generating the iPSCs. This paper reports a method to generate iPSCs from adult human adipose-derived stem cells (hADSCs without the use of a feeder layer, by ectopic expression of the defined transcription factors OCT4, SOX2, KLF4 and C-MYC using a polycistronic plasmid. The results, based on the expression of pluripotent marker, demonstrated that the iPSCs have the characteristics similar to those of embryonic stem cells (ESCs. The iPSCs differentiated into three embryonic germ layers both in vitro by embryoid body generation and in vivo by teratoma formation after being injected into immunodeficient mice. More importantly, the plasmid DNA does not integrate into the genome of human iPSCs as revealed by Southern blotting experiments. Karyotypic analysis also demonstrated that the reprogramming of hADSCs by the defined factors did not induce chromosomal abnormalities. Therefore, this technology provides a platform for studying the biology of iPSCs without viral vectors, and can hopefully overcome immune rejection and ethical concerns, which are the two important barriers of ESC applications.

  16. Simulating Global AeroMACS Airport Ground Station Antenna Power Transmission Limits to Avoid Interference With Mobile Satellite Service Feeder Uplinks

    Science.gov (United States)

    Wilson, Jeffrey D.

    2013-01-01

    The Aeronautical Mobile Airport Communications System (AeroMACS), which is based upon the IEEE 802.16e mobile wireless standard, is expected to be implemented in the 5091 to 5150 MHz frequency band. As this band is also occupied by Mobile Satellite Service feeder uplinks, AeroMACS must be designed to avoid interference with this incumbent service. The aspects of AeroMACS operation that present potential interference are under analysis in order to enable the definition of standards that assure that such interference will be avoided. In this study, the cumulative interference power distribution at low Earth orbit from transmitters at global airports was simulated with the Visualyse Professional software. The dependence of the interference power on antenna distribution, gain patterns, duty cycle, and antenna tilt was simulated. As a function of these parameters, the simulation results are presented in terms of the limitations on transmitter power from global airports required to maintain the cumulative interference power under the established threshold.

  17. The influence of interleukin-2, feeder cells, and timing of irradiation on the radiosensitivity of human T lymphocytes assessed by the colony-forming assay

    International Nuclear Information System (INIS)

    Gerber, M.; Guichard, M.; Pioch, Y.; Dubois, J.B.

    1989-01-01

    The radiosensitivity of human lymphocytes was investigated by the method of colony formation in the absence of interleukin-2 (IL2) and feeder cells, both of which enhance growth of T-cell colonies. The shape of the survival curve and the radiosensitivity was shown to depend upon the ability of lymphocytes to produce IL2: the survival curve for lymphocytes that were the most competent producers of IL2 is the closest to linearity; the lymphocytes that were poor producers show biphasic survival curves. The radiosensitivity of the lymphocytes from the first group is less than that of the latter, when the comparison is based on the first part of the biphasic survival curve. This is more easily seen when cultures are irradiated 24 h after stimulation by phytohemagglutinin (the time of the peak IL2 production) than when cultures are irradiated 2 h before stimulation. This study demonstrates that growth conditions influence the response of lymphocytes to irradiation and that optimal growth conditions result in a linear survival curve

  18. Constant DC-Capacitor Voltage-Control-Based Harmonics Compensation Strategy of Smart Charger for Electric Vehicles in Single-Phase Three-Wire Distribution Feeders

    Directory of Open Access Journals (Sweden)

    Fuka Ikeda

    2017-06-01

    Full Text Available This paper discusses harmonic current compensation of the constant DC-capacitor voltage-control (CDCVC-based strategy of smart chargers for electric vehicles (EVs in single-phase three-wire distribution feeders (SPTWDFs under nonlinear load conditions. The basic principle of the CDCVC-based harmonics compensation strategy under nonlinear load conditions is discussed in detail. The instantaneous power flowing into the three-leg pulse-width modulated (PWM rectifier, which performs as a smart charger, shows that the CDCVC-based strategy achieves balanced and sinusoidal source currents with a unity power factor. The CDCVC-based harmonics compensation strategy does not require any calculation blocks of fundamental reactive, unbalanced active, and harmonic currents. Thus, the authors propose a simplified algorithm to compensate for reactive, unbalanced active, and harmonic currents. A digital computer simulation is implemented to confirm the validity and high practicability of the CDCVC-based harmonics compensation strategy using PSIM software. Simulation results demonstrate that balanced and sinusoidal source currents with a unity power factor in SPTWDFs are obtained on the secondary side of the pole-mounted distribution transformer (PMDT during both the battery-charging and discharging operations in EVs, compensating for the reactive, unbalanced active, and harmonic currents.

  19. Dry deposition on urban surfaces

    International Nuclear Information System (INIS)

    Roed, J.

    1985-01-01

    In order to facilitate developing a model for deposition in urban areas, beryllium-7, created by cosmic radiation and fall-out cesium-137, have been used as tracers in measurements designed to find the dry deposition velocity on building surfaces. A literature review has revealed that very little work has been done on deposition in urban areas; therefore, a major effort on meausring the deposition parameter is needed to construct reliable models in this field. Deposition velocities in the range from 0.001-0.04 cm/s have been found. (author)

  20. Thermal plasma chemical vapor deposition

    International Nuclear Information System (INIS)

    Heberlein, J.; Pfender, E.

    1993-01-01

    Thermal plasmas, with temperatures up to and even exceeding 10 4 K, are capable of producing high density vapor phase precursors for the deposition of relatively thick films. Although this technology is still in its infancy, it will fill the void between the relatively slow deposition processes such as physical vapor deposition and the high rate thermal spray deposition processes. In this chapter, the present state-of-the-art of this field is reviewed with emphasis on the various types of reactors proposed for this emerging technology. Only applications which attracted particular attention, namely diamond and high T c superconducting film deposition, are discussed in greater detail. (orig.)

  1. Uranium ore deposits

    International Nuclear Information System (INIS)

    Angelelli, Victorio.

    1984-01-01

    The main uranium deposits and occurrences in the Argentine Republic are described, considering, in principle, their geologic setting, the kind of 'model' of the mineralization and its possible origin, and describing the ore species present in each case. The main uraniferous accumulations of the country include the models of 'sandstong type', veintype and impregnation type. There are also other kinds of accumulations, as in calcrete, etc. The main uranium production has been registered in the provinces of Mendoza, Salta, La Rioja, Chubut, Cordoba and San Luis. In each case, the minerals present are mentioned, having been recognized 37 different species all over the country (M.E.L.) [es

  2. Deposition of carbon dioxide

    International Nuclear Information System (INIS)

    2001-01-01

    In Norway, there is currently a debate about whether or not to build gas power stations. To meet the possibility of reduced emission quotas for carbon dioxide in the future, current interest focuses on the incorporation of large-scale separation and deposition of carbon dioxide when such plants are planned. A group of experts concludes that this technology will become self-financing by means of environmental taxes. From the environmental point of view, taxes upon production are to be preferred over taxes on consumption

  3. Stratigraphic implications of uranium deposits

    International Nuclear Information System (INIS)

    Langford, F.F.

    1980-01-01

    One of the most consistent characteristics of economic uranium deposits is their restricted stratigraphic distribution. Uraninite deposited with direct igneous affiliation contains thorium, whereas chemical precipitates in sedimentary rocks are characterized by thorium-free primary uranium minerals with vanadium and selenium. In marine sediments, these minerals form low-grade disseminations; but in terrestrial sediments, chiefly fluvial sandstones, the concentration of uranium varies widely, with the high-grade portions constituting ore. Pitchblende vein deposits not only exhibit the same chemical characteristics as the Colorado-type sandstone deposits, but they have a stratigraphically consistent position at unconformities covered by fluvial sandstones. If deposits in such diverse situations have critical features in common, they are likely to have had many features of their origin in common. Thus, vein deposits in Saskatchewan and Australia may have analogues in areas that contain Colorado-type sandstone deposits. In New Mexico, the presence of continental sandstones with peneconformable uranium deposits should also indicate good prospecting ground for unconformity-type vein deposits. All unconformities within the periods of continental deposition ranging from Permian to Cretaceous should have uranium potential. Some situations, such as the onlap of the Abo Formation onto Precambrian basement in the Zuni Mountains, may be directly comparable to Saskatchewan deposition. However, uranium occurrences in the upper part of the Entrada Sandstone suggest that unconformities underlain by sedimentary rocks may also be exploration targets

  4. Sandstone-type uranium deposits

    International Nuclear Information System (INIS)

    Austin, S.R.; D'Andrea, R.F. Jr.

    1978-01-01

    Three overall factors are necessary for formation of uranium deposits in sandstone: a source of uranium, host rocks capable of transmitting uranium-bearing solutions, and a precipitant. Possible sources of uranium in sandstone-type deposits include groundwaters emanating from granitic highlands, arkosic sediments, tuffaceous material within or overlying the host rocks, connate fluids, and overlying black shales. The first three sources are considered the most likely. Host rocks are generally immature sandstones deposited in alluvial-fan, intermontane-basin or marginal-marine environments, but uranium deposits do occur in well-winnowed barrier-bar or eolian sands. Host rocks for uranium deposits generally show coefficients of permeability on the order of 1 to 100 gal/day/ft 2 . Precipitants are normally agents capable of reducing uranium from the uranyl to the uranous state. The association of uranium with organic matter is unequivocal; H 2 S, a powerful reductant, may have been present at the time of formation of some deposits but may go unnoticed today. Vanadium can serve to preserve the tabular characteristics of some deposits in the near-surface environment, but is considered an unlikely primary precipitant for uranium. Uranium deposits in sandstone are divided into two overall types: peneconcordant deposits, which occur in locally reducing environments in otherwise oxidized sandstones; and roll-type deposits, which occur at the margin of an area where an oxidized groundwater has permeated an otherwise reduced sandstone. Uranium deposits are further broken down into four subclasses; these are described

  5. Geological factors of deposit formation

    International Nuclear Information System (INIS)

    Grushevoj, G.V.

    1980-01-01

    Geologic factors of hydrogenic uranium deposit formation are considered. Structural, formation and lithological-facies factors of deposit formation, connected with zones of stratal oxidation, are characterized. Peculiarities of deposit localization, connected with orogenic structures of Mesozoic and lenozoic age, are described. It is noted that deposits of anagenous group are widely spread in Paleozoic formations, infiltration uranium deposits are localized mainly in Cenozoic sediments, while uranium mineralization both anagenous and infiltration groups are widely developed in Mesozoic sediments. Anagenous deposits were formed in non-oxygen situation, their age varies from 200 to 55 mln years. Infiltration deposit formation is determined by asymmetric oxidation zonation, their age varies from 10 - 40 mln years to dozens of thousand years [ru

  6. FDIC Summary of Deposits (SOD) Download File

    Data.gov (United States)

    Federal Deposit Insurance Corporation — The FDIC's Summary of Deposits (SOD) download file contains deposit data for branches and offices of all FDIC-insured institutions. The Federal Deposit Insurance...

  7. Plutonium in uranium deposits

    International Nuclear Information System (INIS)

    Curtis, D.; Fabryka-Martin, J.; Aguilar, R.; Attrep, M. Jr.; Roensch, F.

    1992-01-01

    Plutonium-239 (t 1/2 , 24,100 yr) is one of the most persistent radioactive constituents of high-level wastes from nuclear fission power reactors. Effective containment of such a long-lived constituent will rely heavily upon its containment by the geologic environment of a repository. Uranium ore deposits offer a means to evaluate the geochemical properties of plutonium under natural conditions. In this paper, analyses of natural plutonium in several ores are compared to calculated plutonium production rates in order to evaluate the degree of retention of plutonium by the ore. The authors find that current methods for estimating production rates are neither sufficiently accurate nor precise to provide unambiguous measures of plutonium retention. However, alternative methods for evaluating plutonium mobility are being investigated, including its measurement in natural ground waters. Preliminary results are reported and establish the foundation for a comprehensive characterization of plutonium geochemistry in other natural environments

  8. Classification of Uranium deposits

    International Nuclear Information System (INIS)

    Dahlkamp, F.J.

    1978-01-01

    A listing of the recognized types of uranium mineralization shows nineteen determinable types out of which only six can be classified as of economic significance at present: Oligomiitic quartz pebble conglomerates, sandstone types, calcretes, intra-intrusive types, hydrothermal veins, veinlike types. The different types can be genetically related to prevalent geological environments, i.e. 1. the primary uranium occurrences formed by endogenic processes, 2. the secondary derived from the primary by subsequent exogenic processes, 3. the tertiary occurrences are assumed to be formed by endogenic metamorphic processes, although little is known about the behaviour of the uranium during the metamorphosis and therefore the metallogenesis of this tertiary uranium generation is still vague. A metallotectonic-geochronologic correlation of the uranium deposits shows a distinct affinity of the uranium to certain geological epochs: The Upper Archean, Lower Proterozoic, the Hercynian and, in a less established stage, the Upper Proterozoic. (orig.) 891 HP/orig. 892 MKO [de

  9. Locating underground uranium deposits

    International Nuclear Information System (INIS)

    Felice, P.E.

    1979-01-01

    Underground uranium deposits are located by placing wires of dosimeters each about 5 to 18 mg/cm 2 thick underground in a grid pattern. Each dosimeter contains a phosphor which is capable of storing the energy of alpha particles. In each pair one dosimeter is shielded from alpha particles with more than 18 mg/cm 2 thick opaque material but not gamma and beta rays and the other dosimeter is shielded with less than 1 mg/cm 2 thick opaque material to exclude dust. After a period underground the dosimeters are heated which releases the stored energy as light. The amount of light produced from the heavily shielded dosimeter is subtracted from the amount of light produced from the thinly shielded dosimeter to give an indication of the location and quantity of uranium underground

  10. Generation of functional cardiomyocytes from rat embryonic and induced pluripotent stem cells using feeder-free expansion and differentiation in suspension culture.

    Science.gov (United States)

    Dahlmann, Julia; Awad, George; Dolny, Carsten; Weinert, Sönke; Richter, Karin; Fischer, Klaus-Dieter; Munsch, Thomas; Leßmann, Volkmar; Volleth, Marianne; Zenker, Martin; Chen, Yaoyao; Merkl, Claudia; Schnieke, Angelika; Baraki, Hassina; Kutschka, Ingo; Kensah, George

    2018-01-01

    The possibility to generate cardiomyocytes from pluripotent stem cells in vitro has enormous significance for basic research, disease modeling, drug development and heart repair. The concept of heart muscle reconstruction has been studied and optimized in the rat model using rat primary cardiovascular cells or xenogeneic pluripotent stem cell derived-cardiomyocytes for years. However, the lack of rat pluripotent stem cells (rPSCs) and their cardiovascular derivatives prevented the establishment of an authentic clinically relevant syngeneic or allogeneic rat heart regeneration model. In this study, we comparatively explored the potential of recently available rat embryonic stem cells (rESCs) and induced pluripotent stem cells (riPSCs) as a source for cardiomyocytes (CMs). We developed feeder cell-free culture conditions facilitating the expansion of undifferentiated rPSCs and initiated cardiac differentiation by embryoid body (EB)-formation in agarose microwell arrays, which substituted the robust but labor-intensive hanging drop (HD) method. Ascorbic acid was identified as an efficient enhancer of cardiac differentiation in both rPSC types by significantly increasing the number of beating EBs (3.6 ± 1.6-fold for rESCs and 17.6 ± 3.2-fold for riPSCs). These optimizations resulted in a differentiation efficiency of up to 20% cTnTpos rPSC-derived CMs. CMs showed spontaneous contractions, expressed cardiac markers and had typical morphological features. Electrophysiology of riPSC-CMs revealed different cardiac subtypes and physiological responses to cardio-active drugs. In conclusion, we describe rPSCs as a robust source of CMs, which is a prerequisite for detailed preclinical studies of myocardial reconstruction in a physiologically and immunologically relevant small animal model.

  11. Spatio-Temporal Variation in Effects of Upwelling on the Fatty Acid Composition of Benthic Filter Feeders in the Southern Benguela Ecosystem: Not All Upwelling Is Equal.

    Directory of Open Access Journals (Sweden)

    Eleonora Puccinelli

    Full Text Available Variability in mesoscale nearshore oceanographic conditions plays an important role in the distribution of primary production and food availability for intertidal consumers. Advection of nutrient rich waters by upwelling usually allows the proliferation of diatoms, later replaced by dinoflagellates. We examined upwelling effects on the fatty acid (FA signature of a benthic intertidal filter feeder to identify its response to pulsed variability in food availability. The study took place in two contrasting seasons and at two upwelling and two non-upwelling sites interspersed within the southern Benguela upwelling system of South Africa. We investigated the FA composition of the adductor muscles and gonads of the mussel Mytilus galloprovincialis to assess how FA are apportioned to the different tissues and whether this changes between upwelling and non-upwelling conditions. In situ temperature loggers used to identify upwelling conditions at the four sites indicated that such events occurred only at the upwelling centres and only in summer. Tissues differed strongly, with gonads presenting a higher proportion of essential FAs. This could reflect the faster turnover rate of gonad tissue or preferential retention of specific FA for reproductive purposes. FA composition did not vary as a direct function of upwelling, but there were strong dissimilarities among sites. Upwelling influenced mussel diets at one upwelling site while at the other, the expected signature of upwelling was displaced downstream of the core of upwelling. Condition Index (CI and Gonad Index (GI differed among sites and were not influenced by upwelling, with GI being comparable among sites. In addition, FA proportions were consistent among sites, indicating similar food quality and quantity over time and under upwelling and non-upwelling conditions. This suggests that the influence of upwelling on the west coast of South Africa is pervasive and diffuse, rather than discrete; while

  12. Global deposition of airborne dioxin.

    Science.gov (United States)

    Booth, Shawn; Hui, Joe; Alojado, Zoraida; Lam, Vicky; Cheung, William; Zeller, Dirk; Steyn, Douw; Pauly, Daniel

    2013-10-15

    We present a global dioxin model that simulates one year of atmospheric emissions, transport processes, and depositions to the earth's terrestrial and marine habitats. We map starting emission levels for each land area, and we also map the resulting deposits to terrestrial and marine environments. This model confirms that 'hot spots' of deposition are likely to be in northern Europe, eastern North America, and in parts of Asia with the highest marine dioxin depositions being the northeast and northwest Atlantic, western Pacific, northern Indian Ocean and the Mediterranean. It also reveals that approximately 40% of airborne dioxin emissions are deposited to marine environments and that many countries in Africa receive more dioxin than they produce, which results in these countries being disproportionately impacted. Since human exposure to dioxin is largely through diet, this work highlights food producing areas that receive higher atmospheric deposits of dioxin than others. Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. A remote coal deposit revisited

    DEFF Research Database (Denmark)

    Bojesen-Kofoed, Jørgen A.; Kalkreuth, Wolfgang; Petersen, Henrik I.

    2012-01-01

    discovery. The outcrops found in 2009 amount to approximately 8 m of sediment including a coal seam of 2 m thickness. More outcrops and additional coal deposits most certainly are to be found, pending further fieldwork. The deposits are Middle Jurassic, Callovian, in age and were deposited in a floodplain...... environment related to meandering river channels. Spores and pollen in the lower fluvial deposits reflect abundant vegetation of ferns along the river banks. In contrast, a sparse spore and pollen flora in the coals show a mixed vegetation of ferns and gymnosperms. Based on proximate and petrographic analyses...

  14. 76 FR 41392 - Interest on Deposits; Deposit Insurance Coverage

    Science.gov (United States)

    2011-07-14

    ... banks' funding costs and also allow them to plan business growth more dependably and rigorously... of business deposits by offering continually higher rates of interest. Three of the four contended... deposits. They reasoned that large banks will offer high rates of interest and lure away business...

  15. Uranium deposits in granitic rocks

    International Nuclear Information System (INIS)

    Nishimori, R.K.; Ragland, P.C.; Rogers, J.J.W.; Greenberg, J.K.

    1977-01-01

    This report is a review of published data bearing on the geology and origin of uranium deposits in granitic, pegmatitic and migmatitic rocks with the aim of assisting in the development of predictive criteria for the search for similar deposits in the U.S. Efforts were concentrated on the so-called ''porphyry'' uranium deposits. Two types of uranium deposits are primarily considered: deposits in pegmatites and alaskites in gneiss terrains, and disseminations of uranium in high-level granites. In Chapter 1 of this report, the general data on the distribution of uranium in igneous and metamorphic rocks are reviewed. Chapter 2 contains some comments on the classification of uranium deposits associated with igneous rocks and a summary of the main features of the geology of uranium deposits in granites. General concepts of the behavior of uranium in granites during crustal evolution are reviewed in Chapter 3. Also included is a discussion of the relationship of uranium mineralization in granites to the general evolution of mobile belts, plus the influence of magmatic and post-magmatic processes on the distribution of uranium in igneous rocks and related ore deposits. Chapter 4 relates the results of experimental studies on the crystallization of granites to some of the geologic features of uranium deposits in pegmatites and alaskites in high-grade metamorphic terrains. Potential or favorable areas for igneous uranium deposits in the U.S.A. are delineated in Chapter 5. Data on the geology of specific uranium deposits in granitic rocks are contained in Appendix 1. A compilation of igneous rock formations containing greater than 10 ppM uranium is included in Appendix 2. Appendix 3 is a report on the results of a visit to the Roessing area. Appendix 4 is a report on a field excursion to eastern Canada

  16. Enhanced nitrogen deposition over China

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Xuejun; Zhang, Ying; Han, Wenxuan; Tang, Aohan; Shen, Jianlin; Cui, Zhenling; Christie, Peter; Zhang, Fusuo [College of Resources and Environmental Sciences, China Agricultural University, Beijing 100193 (China); Vitousek, Peter [Department of Biology, Stanford University, Stanford, California 94305 (United States); Erisman, Jan Willem [VU University Amsterdam, 1081 HV Amsterdam (Netherlands); Goulding, Keith [The Sustainable Soils and Grassland Systems Department, Rothamsted Research, Harpenden AL5 2JQ (United Kingdom); Fangmeier, Andreas [Institute of Landscape and Plant Ecology, University of Hohenheim, 70593 Stuttgart (Germany)

    2013-02-28

    China is experiencing intense air pollution caused in large part by anthropogenic emissions of reactive nitrogen. These emissions result in the deposition of atmospheric nitrogen (N) in terrestrial and aquatic ecosystems, with implications for human and ecosystem health, greenhouse gas balances and biological diversity. However, information on the magnitude and environmental impact of N deposition in China is limited. Here we use nationwide data sets on bulk N deposition, plant foliar N and crop N uptake (from long-term unfertilized soils) to evaluate N deposition dynamics and their effect on ecosystems across China between 1980 and 2010. We find that the average annual bulk deposition of N increased by approximately 8 kilograms of nitrogen per hectare (P < 0.001) between the 1980s (13.2 kilograms of nitrogen per hectare) and the 2000s (21.1 kilograms of nitrogen per hectare). Nitrogen deposition rates in the industrialized and agriculturally intensified regions of China are as high as the peak levels of deposition in northwestern Europe in the 1980s, before the introduction of mitigation measures. Nitrogen from ammonium (NH4+) is the dominant form of N in bulk deposition, but the rate of increase is largest for deposition of N from nitrate (NO3-), in agreement with decreased ratios of NH3 to NOx emissions since 1980. We also find that the impact of N deposition on Chinese ecosystems includes significantly increased plant foliar N concentrations in natural and semi-natural (that is, non-agricultural) ecosystems and increased crop N uptake from long-term-unfertilized croplands. China and other economies are facing a continuing challenge to reduce emissions of reactive nitrogen, N deposition and their negative effects on human health and the environment.

  17. Non-selective photoionization of Rubidium

    International Nuclear Information System (INIS)

    1987-01-01

    Effusive atomic beam of Rubidium have been generated through an effusive source. An oriel uv-light source was focused to irradiate and interact with atomic beam of Rb. The energy of the uv-lamp was enough to raise the Rb atom by 4.17 eV to the ionization continuum level of Rb

  18. Liquefier Dynamics in Fused Deposition

    DEFF Research Database (Denmark)

    Bellini, Anna; Guceri, Selcuk; Bertoldi, Maurizio

    2004-01-01

    Layered manufacturing (LM) is an evolution of rapid prototyping (RP) technology whereby a part is built in layers. Fused deposition modeling (FDM) is a particular LM technique in which each section is fabricated through vector style deposition of building blocks, called roads, which...

  19. NURE uranium deposit model studies

    International Nuclear Information System (INIS)

    Crew, M.E.

    1981-01-01

    The National Uranium Resource Evaluation (NURE) Program has sponsored uranium deposit model studies by Bendix Field Engineering Corporation (Bendix), the US Geological Survey (USGS), and numerous subcontractors. This paper deals only with models from the following six reports prepared by Samuel S. Adams and Associates: GJBX-1(81) - Geology and Recognition Criteria for Roll-Type Uranium Deposits in Continental Sandstones; GJBX-2(81) - Geology and Recognition Criteria for Uraniferous Humate Deposits, Grants Uranium Region, New Mexico; GJBX-3(81) - Geology and Recognition Criteria for Uranium Deposits of the Quartz-Pebble Conglomerate Type; GJBX-4(81) - Geology and Recognition Criteria for Sandstone Uranium Deposits in Mixed Fluvial-Shallow Marine Sedimentary Sequences, South Texas; GJBX-5(81) - Geology and Recognition Criteria for Veinlike Uranium Deposits of the Lower to Middle Proterozoic Unconformity and Strata-Related Types; GJBX-6(81) - Geology and Recognition Criteria for Sandstone Uranium Deposits of the Salt Wash Type, Colorado Plateau Province. A unique feature of these models is the development of recognition criteria in a systematic fashion, with a method for quantifying the various items. The recognition-criteria networks are used in this paper to illustrate the various types of deposits

  20. Sandstone-type uranium deposits

    International Nuclear Information System (INIS)

    Finch, W.I.; Davis, J.F.

    1985-01-01

    World-class sandstone-type uranium deposits are defined as epigenetic concentrations of uranium minerals occurring as uneven impregnations and minor massive replacements primarily in fluvial, lacustrine, and deltaic sandstone formations. The main purpose of this introductory paper is to define, classify, and introduce to the general geologic setting for sandstone-type uranium deposits

  1. Laser deposition of HTSC films

    International Nuclear Information System (INIS)

    Sobol', Eh.N.; Bagratashvili, V.N.; Zherikhin, A.N.; Sviridov, A.P.

    1990-01-01

    Studies of the high-temperature superconducting (HTSC) films fabrication by the laser deposition are reviewed. Physical and chemical processes taking place during laser deposition are considered, such as the target evaporation, the material transport from the target to the substrate, the film growth on the substrate, thermochemical reactions and mass transfer within the HTSC films and their stability. The experimental results on the laser deposition of different HTSC ceramics and their properties investigations are given. The major technological issues are discussed including the deposition schemes, the oxygen supply, the target compositions and structure, the substrates and interface layers selection, the deposition regimes and their impact on the HTSC films properties. 169 refs.; 6 figs.; 2 tabs

  2. Polymer deposition morphology by electrospray deposition - Modifications through distance variation

    International Nuclear Information System (INIS)

    Altmann, K.; Schulze, R.-D.; Friedrich, J.

    2014-01-01

    Electrospray deposition (ESD) of highly diluted polymers was examined with regard to the deposited surface structure. Only the flight distance (flight time) onto the resulting deposited surface was varied from 20 to 200 mm. An apparatus without any additional heating or gas flows was used. Polyacrylic acid (PAA) and polyallylamine (PAAm) in methanol were deposited on Si wafers. The polymer layers were characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, derivatization reactions and Fourier transform infrared spectroscopy using a grazing incidence unit. SEM images illustrated the changing structures of PAA and PAAm. For PAA the deposited structure changed from a smooth film (20 mm) to a film with individual droplets on the coated surface (100 mm and 200 mm), while for PAAm individual droplets can be seen at all distances. The ESD process with cascades of splitting droplets slows down for PAA after distances greater than 40 mm. In contrast, the ESD process for PAAm is nearly stopped within the first flight distance of 20 mm. Residual solvent analysis showed that most of the solvent evaporated within the first 20 mm capillary-sample distance. - Highlights: • We deposited polyacrylic acid and polyallylamine by electrospray ionization (ESI). • The morphology in dependence of flight distance (20 mm to 200 mm) was analyzed. • The amount of residual solvent after deposition was determined. • ESI-process slows down for polyacrylic acid after 40 mm flight distance. • ESI-Process is complete for polyallylamine within the first 20 mm

  3. 20 CFR 703.207 - Kinds of negotiable securities that may be deposited; conditions of deposit; acceptance of deposits.

    Science.gov (United States)

    2010-04-01

    ... amount fixed by the Office under the regulations in this part shall deposit any negotiable securities... deposited; conditions of deposit; acceptance of deposits. 703.207 Section 703.207 Employees' Benefits... AND RELATED STATUTES INSURANCE REGULATIONS Insurance Carrier Security Deposit Requirements § 703.207...

  4. Geometric design of part feeders

    NARCIS (Netherlands)

    Berretty, R.-P.M.

    2000-01-01

    This thesis presents solutions for problems derived from industrial assembly and robotic manipulation. The basic tasks in a factory are manufacturing the parts, and combining them into the desired product. In automating these tasks, we want to use robot manipulators that require little or no

  5. Quasi-static time-series simulation using OpenDSS in IEEE distribution feeder model with high PV penetration and its impact on solar forecasting

    Science.gov (United States)

    Mohammed, Touseef Ahmed Faisal

    Distribution System Simulator developed by Electric Power Research Institute, to simulate grid voltage profile with a large scale PV system under quasi-static time series considering variations of PV output in seconds, minutes, and the average daily load variations. A 13 bus IEEE distribution feeder model is utilized with distributed residential and commercial scale PV at different buses for simulation studies. Time series simulations are discussed for various modes of operation considering dynamic PV penetration at different time periods in a day. In addition, this thesis demonstrates simulations taking into account the presence of moving cloud for solar forecasting studies.

  6. How to insure measurement accuracy of belt feeder machine weighing installment%如何保证皮带绐料机称重装置的计量精度

    Institute of Scientific and Technical Information of China (English)

    李双; 吴江; 陈以振

    2012-01-01

    本文从皮带给料机这一称重产品的结构、校准原理、计量精度等几个主要方面,以图文结合的形式着重阐述了怎样保证皮带给料机称重装置的计量精度。%In the form of a graphic combination, according to structure, calibration principle, measurement accuracy and some other factors, this article elaborates how to insure measurement accuracy of belt feeder machine weighing installmenL

  7. Surface deposition from radioactive plumes

    International Nuclear Information System (INIS)

    Garland, J.A.

    1980-01-01

    Accidents involving nuclear plants may release radioactive particles and gases to the atmosphere. Dry deposition of particles has been investigated mainly in the laboratory and a general understanding of the transfer mechanisms has been established. However there is apparently a substantial discrepancy between the few field observations of dry deposition of particles and laboratory measurements, particularly for 0.1 - 1 μm particles for which laboratory work shows very small deposition rates. In addition there are few estimates of deposition rates for forest and some other kinds of terrain. The most important gas in the context of a nuclear accident is I-131 and the behaviour of this gas at grass surfaces has received much attention. However smaller quantities of other gases and vapours may be released and the surface absorption of these species may require further investigation. In addition there is little knowledge of the behaviour of gases over many types of surface. The rate of deposition of particles and gases is influenced by many parameters including wind speed and the temperature stratification of the lower atmosphere. Conditions which give poor atmospheric dispersion usually give lower deposition velocities. Transfer to man depends on the availability of deposited materials on crops and grass. A wide range of isotopes including iodine and several metallic fission products are lost with a half life for residence on grass ranging from a few days to a few tens days, depending on climatic conditions

  8. ITO thin films deposited by advanced pulsed laser deposition

    International Nuclear Information System (INIS)

    Viespe, Cristian; Nicolae, Ionut; Sima, Cornelia; Grigoriu, Constantin; Medianu, Rares

    2007-01-01

    Indium tin oxide thin films were deposited by computer assisted advanced PLD method in order to obtain transparent, conductive and homogeneous films on a large area. The films were deposited on glass substrates. We studied the influence of the temperature (room temperature (RT)-180 deg. C), pressure (1-6 x 10 -2 Torr), laser fluence (1-4 J/cm 2 ) and wavelength (266-355 nm) on the film properties. The deposition rate, roughness, film structure, optical transmission, electrical conductivity measurements were done. We deposited uniform ITO thin films (thickness 100-600 nm, roughness 5-10 nm) between RT and 180 deg. C on a large area (5 x 5 cm 2 ). The films have electrical resistivity of 8 x 10 -4 Ω cm at RT, 5 x 10 -4 Ω cm at 180 deg. C and an optical transmission in the visible range, around 89%

  9. Atmospheric deposition 2000. NOVA 2003; Atmosfaerisk deposition 2000. NOVA 2003

    Energy Technology Data Exchange (ETDEWEB)

    Ellermann, T.; Hertel, O.; Hovmand, M.F.; Kemp, K.; Skjoeth, C.A.

    2001-11-01

    This report presents measurements and calculations from the atmospheric part of NOVA 2003 and covers results for 2000. It summarises the main results concerning concentrations and depositions of nitrogen, phosphorus and sulphur compounds related to eutrophication and acidification. Depositions of atmospheric compounds to Danish marine waters as well as land surface are presented. Measurements: In 2000 the monitoring program consisted of eight stations where wet deposition of ammonium, nitrate, phosphate (semi quantitatively) and sulphate were measured using bulk precipitation samplers. Six of the stations had in addition measurements of atmospheric content of A, nitrogen, phosphorus, and sulphur compounds in gas and particulate phase carried out by use of filter pack samplers. Filters were analysed at the National Environmental Research Institute. Furthermore nitrogen dioxide were measured using nitrogen dioxide filter samplers and monitors. Model calculations: The measurements in the monitoring program were supplemented with model calculations of concentrations and depositions of nitrogen and sulphur compounds to Danish land surface, marine waters, fjords and bays using the ACDEP model (Atmospheric Chemistry and Deposition). The model is a so-called trajectory model and simulates the physical and chemical processes in the atmosphere using meteorological and emission data as input. The advantage of combining measurements with model calculations is that the strengths of both methods is obtained. Conclusions concerning: 1) actual concentration levels at the monitoring stations, 2) deposition at the monitoring stations, 3) seasonal variations and 4) long term trends in concentrations and depositions are mainly based on the direct measurements. These are furthermore used to validate the results of the model calculations. Calculations and conclusions concerning: 1) depositions to land surface and to the individual marine water, 2) contributions from different emission

  10. Particle deposition in ventilation ducts

    Energy Technology Data Exchange (ETDEWEB)

    Sippola, Mark Raymond [Univ. of California, Berkeley, CA (United States)

    2002-09-01

    Exposure to airborne particles is detrimental to human health and indoor exposures dominate total exposures for most people. The accidental or intentional release of aerosolized chemical and biological agents within or near a building can lead to exposures of building occupants to hazardous agents and costly building remediation. Particle deposition in heating, ventilation and air-conditioning (HVAC) systems may significantly influence exposures to particles indoors, diminish HVAC performance and lead to secondary pollutant release within buildings. This dissertation advances the understanding of particle behavior in HVAC systems and the fates of indoor particles by means of experiments and modeling. Laboratory experiments were conducted to quantify particle deposition rates in horizontal ventilation ducts using real HVAC materials. Particle deposition experiments were conducted in steel and internally insulated ducts at air speeds typically found in ventilation ducts, 2-9 m/s. Behaviors of monodisperse particles with diameters in the size range 1-16 μm were investigated. Deposition rates were measured in straight ducts with a fully developed turbulent flow profile, straight ducts with a developing turbulent flow profile, in duct bends and at S-connector pieces located at duct junctions. In straight ducts with fully developed turbulence, experiments showed deposition rates to be highest at duct floors, intermediate at duct walls, and lowest at duct ceilings. Deposition rates to a given surface increased with an increase in particle size or air speed. Deposition was much higher in internally insulated ducts than in uninsulated steel ducts. In most cases, deposition in straight ducts with developing turbulence, in duct bends and at S-connectors at duct junctions was higher than in straight ducts with fully developed turbulence. Measured deposition rates were generally higher than predicted by published models. A model incorporating empirical equations based on the

  11. Acid Deposition Maps in Spain

    International Nuclear Information System (INIS)

    Artinano, B.; Cabal, H.; Garcia, C.

    1998-01-01

    Animal and monthly deposition velocity and total sulfur deposition maps have been performed for the peninsular Spain for 1992 by using the inferential method. To do this, updated databases with high space and time resolution, for land uses (CORINE) and meteorological information from analysis modelling for the same year, have been utilized. The final result are deposition maps in a 5x5 Km 2 grid which allow to assess the methodology used in Europe to obtain the maps of excedances over the critical loads of pollutants. (Author) 32 refs

  12. The anthracite of Nazar-Aylok Deposit

    International Nuclear Information System (INIS)

    Pachadzhanov, D.N.; Valiev, Yu.Ya.

    2013-01-01

    Present article is devoted to anthracite of Nazar-Aylok Deposit. The ash content, composition of coals of Nazar-Aylok Deposit and thickness of deposit were considered. The coal samples were studied by means of neutron activation analysis.

  13. Deposition of Boron in Possible Evaporite Deposits in Gale Crate

    Science.gov (United States)

    Gasda, P. J.; Peets, E.; Lamm, S. N.; Rapin, W.; Lanza, N.; Frydenvang, J.; Clark, B. C.; Herkenhoff, K. E.; Bridges, J.; Schwenzer, S. P.; Haldeman, E. B.; Wiens, R. C.; Maurice, S.; Clegg, S. M.; Delapp, D.; Sanford, V.; Bodine, M. R.; McInroy, R.

    2017-12-01

    Boron has been previously detected in Gale crater using the ChemCam instrument on board the NASA Curiosity rover within calcium sulfate fracture fill hosted by lacustrine mudstone and eolian sandstone units. Recent results show that up to 300 ppm B is present in the upper sections of the lacustrine unit. Boron has been detected in both the groundwater-emplaced calcium sulfate fracture fill materials and bedding-parallel calcium sulfate layers. The widespread bedding-parallel calcium sulfate layers within the upper strata of the lacustrine bedrock that Curiosity has encountered recently could be interpreted as primary evaporite deposits. We have two hypotheses for the history of boron in Gale crater. In both hypotheses, borates were first deposited as lake water evaporated, depositing primary evaporates that were later re-dissolved by groundwater, which redistributed the boron into secondary evaporitic calcium sulfate fracture fill deposits. In the first scenario, Gale crater may have undergone a period of perennial lake formation during a drier period of martian history, depositing layers of evaporitic minerals (including borates) among lacustrine mudstone layers. In the second scenario, lake margins could have become periodically exposed during cyclic drops in lake level and subsequently desiccated. Evaporites were deposited and desiccation features were formed in lowstand deposits. Either hypothetical scenario of evaporite deposition would promote prebiotic chemical reactions via wet-dry cycles. Boron may be an important prebiotic element, and as such, its presence in ancient martian surface and groundwater provides evidence that important prebiotic chemical reactions could occur on Mars if organics were present. The presence of boron in ancient Gale crater groundwater also provides additional evidence that a habitable environment existed in the martian subsurface well after the expected disappearance of liquid water on the surface of Mars. We will report on the

  14. Atomic layer deposition for semiconductors

    CERN Document Server

    Hwang, Cheol Seong

    2014-01-01

    This edited volume discusses atomic layer deposition (ALD) for all modern semiconductor devices, moving from the basic chemistry of ALD and modeling of ALD processes to sections on ALD for memories, logic devices, and machines.

  15. Gasoline from Kumkol deposit petroleum

    International Nuclear Information System (INIS)

    Nadirov, A.N.; Zhizhin, N.I.; Musaeva, Z.G.

    1997-01-01

    Samples of gasoline from petroleum of Kumkol deposit are investigated by chromatographic analysis. It is found, that gasoline is characterizing by increased content of iso-paraffin hydrocarbons. (author)

  16. Temporal stability and rates of post-depositional change in geochemical signatures of brown trout Salmo trutta scales.

    Science.gov (United States)

    Ryan, D; Shephard, S; Kelly, F L

    2016-09-01

    This study investigates temporal stability in the scale microchemistry of brown trout Salmo trutta in feeder streams of a large heterogeneous lake catchment and rates of change after migration into the lake. Laser-ablation inductively coupled plasma mass spectrometry was used to quantify the elemental concentrations of Na, Mg, Mn, Cu, Zn, Ba and Sr in archived (1997-2002) scales of juvenile S. trutta collected from six major feeder streams of Lough Mask, County Mayo, Ireland. Water-element Ca ratios within these streams were determined for the fish sampling period and for a later period (2013-2015). Salmo trutta scale Sr and Ba concentrations were significantly (P < 0·05) correlated with stream water sample Sr:Ca and Ba:Ca ratios respectively from both periods, indicating multi-annual stability in scale and water-elemental signatures. Discriminant analysis of scale chemistries correctly classified 91% of sampled juvenile S. trutta to their stream of origin using a cross-validated classification model. This model was used to test whether assumed post-depositional change in scale element concentrations reduced correct natal stream classification of S. trutta in successive years after migration into Lough Mask. Fish residing in the lake for 1-3 years could be reliably classified to their most likely natal stream, but the probability of correct classification diminished strongly with longer lake residence. Use of scale chemistry to identify natal streams of lake S. trutta should focus on recent migrants, but may not require contemporary water chemistry data. © 2016 The Fisheries Society of the British Isles.

  17. Electrospark deposition for die repair

    Directory of Open Access Journals (Sweden)

    J. Tušek

    2012-01-01

    Full Text Available The electrospark deposition is a process for surfacing of hard metal alloys, e.g. carbides and stellites, on the surfaces of new or old machine elements. In this process, a high current is conducted through an oscillating electrode and a substrate for a very short period of time. In the paper, the process is described and the thickness of deposited layer, chemical composition, dilution rate and the layer roughness are determined.

  18. A radon progeny deposition model

    International Nuclear Information System (INIS)

    Rielage, Keith; Elliott, Steven R.; Hime, Andrew; Guiseppe, Vincent E.; Westerdale, S.

    2010-01-01

    The next generation low-background detectors operating underground aim for unprecedented low levels of radioactive backgrounds. Although the radioactive decays of airborne radon (particularly 222 Rn) and its subsequent progeny present in an experiment are potential backgrounds, also problematic is the deposition of radon progeny on detector materials. Exposure to radon at any stage of assembly of an experiment can result in surface contamination by progeny supported by the long half life (22 y) of 210 Pb on sensitive locations of a detector. An understanding of the potential surface contamination from deposition will enable requirements of radon-reduced air and clean room environments for the assembly of low background experiments. It is known that there are a number of environmental factors that govern the deposition of progeny onto surfaces. However, existing models have not explored the impact of some environmental factors important for low background experiments. A test stand has been constructed to deposit radon progeny on various surfaces under a controlled environment in order to develop a deposition model. Results from this test stand and the resulting deposition model are presented.

  19. A Radon Progeny Deposition Model

    International Nuclear Information System (INIS)

    Guiseppe, V. E.; Elliott, S. R.; Hime, A.; Rielage, K.; Westerdale, S.

    2011-01-01

    The next generation low-background detectors operating underground aim for unprecedented low levels of radioactive backgrounds. Although the radioactive decays of airborne radon (particularly 222 Rn) and its subsequent progeny present in an experiment are potential backgrounds, also problematic is the deposition of radon progeny on detector materials. Exposure to radon at any stage of assembly of an experiment can result in surface contamination by progeny supported by the long half life (22 y) of 210 Pb on sensitive locations of a detector. An understanding of the potential surface contamination from deposition will enable requirements of radon-reduced air and clean room environments for the assembly of low background experiments. It is known that there are a number of environmental factors that govern the deposition of progeny onto surfaces. However, existing models have not explored the impact of some environmental factors important for low background experiments. A test stand has been constructed to deposit radon progeny on various surfaces under a controlled environment in order to develop a deposition model. Results from this test stand and the resulting deposition model are presented.

  20. Legal Deposit of Electronic Publications

    Directory of Open Access Journals (Sweden)

    Burcu Umut Zan

    2009-06-01

    Full Text Available The most important and basic role of the deposition studies, which are the greatest contributions to the knowledge sharing, is to gather the artistic and philosophical works of a country and provide them for the use of future researchers. However, since early deposition studies were limited with printed publications, they do not involve the electronic publication types appearing with the development of information technology. This stems from the fact that the electronic publications require procedures different from those of the printed publications in terms of deposition steps because of their structures. Today, in order to guarantee that all registered cultural products, which are mostly produced and used in the electronic environment could be fully collected, electronic publications should also be covered by and regulated under legal deposit. This study analyzes the deposition of electronic publications, within the framework of their storage and protection, being put in the use of the users as well as the common approaches to deposition practices in the world parallel to the developments in the information technology. The related situation in Turkey was also evaluated.

  1. The SYOEKSY research project. Electrically-powered vehicles in ring rail line feeder traffic and short-distance travel; Saehkoeiset ajoneuvot kehaeradan syoettoe- ja asiointiliikenteessae. SYOEKSY-tutkimushankkeen loppuraportti 21.9.2011

    Energy Technology Data Exchange (ETDEWEB)

    2011-07-01

    The research report is divided into three sections: a general description of the project, separate reports on each of the themes investigated and a summary of the research results and recommendations. Section 2 deals with themes such as: Low-emissions-technology solutions for traffic and their technical prerequisites in an urban environment and the results obtained from pilot projects. New service models based on electrically-powered traffic technology with an assessment of their feasibility and their effect on urban infrastructure and levels of CO{sub 2} emissions. User needs in new feeder traffic, short-distance travel and other journeys on personal business together with proposals for planning measures which will promote sustainable mobility in new residential areas. The prerequisites for electrically-powered feeder traffic and short-distance travel are therefore handled in a wide-ranging manner. A condensed version of the project conclusions and recommendations is provided in Section 3. A list of the data sources and publications resulting from project work can be found at the end of the report

  2. Spatial variations of wet deposition rates in an extended region of complex topography deduced from measurements of 210Pb soil inventories

    International Nuclear Information System (INIS)

    Branford, D.; Mourne, R.W.; Fowler, D.

    1998-01-01

    The radionuclide 210 Pb derived from gaseous 222 Rn present in the atmosphere becomes attached to the same aerosols as the bulk of the main pollutants sulphur and nitrogen. When scavenged from the atmosphere by precipitation, the 210 Pb is readily attached to organic matter in the surface horizons of the soil. Inventories of 210 Pb in soil can thus be used to measure the spatial variations in wet (or cloud) deposition due to orography averaged over many precipitation events (half-life of 210 Pb is 22·3 year). Measurements of soil 210 Pb inventories were made along a transect through complex terrain in the Scottish Highlands to quantify the orographic enhancement of wet deposition near the summits of the three mountains Ben Cruachan, Beinn Dorain and Ben Lawers, which, respectively, lie at distances of approximately 30, 55 and 80 km from the coast in the direction of the prevailing wind. The inventory of 210 Pb on the wind-facing slopes of Ben Cruachan shows an increase with altitude that rises faster than the precipitation rate, which is indicative of seeder-feeder scavenging of orographic cloud occurring around the summit. Results for Beinn Dorain show a smaller rise with altitude whereas those for Ben Lawers give no indication of a rise. It is concluded that the seeder-feeder mechanism in regions of complex topology decreases in effectiveness as a function of distance inland along the direction of the prevailing wind. (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

  3. Closed-Loop Process Control for Electron Beam Freeform Fabrication and Deposition Processes

    Science.gov (United States)

    Taminger, Karen M. (Inventor); Hafley, Robert A. (Inventor); Martin, Richard E. (Inventor); Hofmeister, William H. (Inventor)

    2013-01-01

    A closed-loop control method for an electron beam freeform fabrication (EBF(sup 3)) process includes detecting a feature of interest during the process using a sensor(s), continuously evaluating the feature of interest to determine, in real time, a change occurring therein, and automatically modifying control parameters to control the EBF(sup 3) process. An apparatus provides closed-loop control method of the process, and includes an electron gun for generating an electron beam, a wire feeder for feeding a wire toward a substrate, wherein the wire is melted and progressively deposited in layers onto the substrate, a sensor(s), and a host machine. The sensor(s) measure the feature of interest during the process, and the host machine continuously evaluates the feature of interest to determine, in real time, a change occurring therein. The host machine automatically modifies control parameters to the EBF(sup 3) apparatus to control the EBF(sup 3) process in a closed-loop manner.

  4. Felsic magmatism and uranium deposits

    International Nuclear Information System (INIS)

    Cuney, Michel

    2014-01-01

    The strongly incompatible behaviour of uranium in silicate magmas results in its concentration in the most felsic melts and a prevalence of granites and rhyolites as primary U sources for the formation of U deposits. Despite its incompatible behavior, U deposits resulting directly from magmatic processes are quite rare. In most deposits, U is mobilized by hydrothermal fluids or ground water well after the emplacement of the igneous rocks. Of the broad range of granite types, only a few have U contents and physico-chemical properties that permit the crystallization of accessory minerals from which uranium can be leached for the formation of U deposits. The first granites on Earth, which crystallized uraninite, dated at 3.1 Ga, are the potassic granites from the Kaapval craton (South Africa) which were also the source of the detrital uraninite for the Dominion Reef and Witwatersrand quartz pebble conglomerate deposits. Four types of granites or rhyolites can be sufficiently enriched in U to represent a significant source for the genesis of U deposits: per-alkaline, high-K met-aluminous calc-alkaline, L-type peraluminous and anatectic pegmatoids. L-type peraluminous plutonic rocks in which U is dominantly hosted in uraninite or in the glass of their volcanic equivalents represent the best U source. Per-alkaline granites or syenites are associated with the only magmatic U-deposits formed by extreme fractional crystallization. The refractory character of the U-bearing minerals does not permit their extraction under the present economic conditions and make them unfavorable U sources for other deposit types. By contrast, felsic per-alkaline volcanic rocks, in which U is dominantly hosted in the glassy matrix, represent an excellent source for many deposit types. High-K calc-alkaline plutonic rocks only represent a significant U source when the U-bearing accessory minerals (U-thorite, allanite, Nb oxides) become metamict. The volcanic rocks of the same geochemistry may be

  5. Felsic magmatism and uranium deposits

    International Nuclear Information System (INIS)

    Cuney, M.

    2014-01-01

    Uranium strongly incompatible behaviour in silicate magmas results in its concentration in the most felsic melts and a prevalence of granites and rhyolites as primary U sources for the formation of U deposits. Despite its incompatible behaviour, U deposits resulting directly from magmatic processes are quite rare. In most deposits, U is mobilized by hydrothermal fluids or ground water well after the emplacement of the igneous rocks. Of the broad range of granite types, only a few have have U contents and physico-chemical properties that permit the crystallization of accessory minerals from which uranium can be leached for the formation of U deposits. The first granites on Earth which crystallized uraninite appeared at 3.1 Ga, are the potassic granites from the Kaapval craton (South Africa) which were also the source of the detrital uraninite for the Dominion Reef and Witwatersrand quartz pebble conglomerate deposits. Four types of granites or rhyolites can be sufficiently enriched in U to represent a significant source for the genesis of U deposits: peralkaline, high-K metaluminous calc-alkaline, L-type peraluminous ones and anatectic pegmatoids. L-type peraluminous plutonic rocks in which U is dominantly hosted in uraninite or in the glass in their volcanic equivalents represent the best U source. Peralkaline granites or syenites represent the only magmatic U-deposits formed by extreme fractional crystallization. The refractory character of the U-bearing minerals does not permit their extraction at the present economic conditions and make them unfavourable U sources for other deposit types. By contrast, felsic peralkaline volcanic rocks, in which U is dominantly hosted in the glassy matrix, represent an excellent source for many deposit types. High-K calc-alkaline plutonic rocks only represent a significant U source when the U-bearing accessory minerals [U-thorite, allanite, Nb oxides] become metamict. The volcanic rocks of the same geochemistry may be also a

  6. Vein-type uranium deposits

    International Nuclear Information System (INIS)

    Rich, R.A.; Holland, H.D.; Petersen, U.

    1975-01-01

    A critical review is presented of published data bearing on the mineralogy, paragenesis, geochemistry, and origin of veiw-type uranium deposits. Its aim is to serve as a starting point for new research and as a basis for the development of new exploration strategies. During the formation of both vein and sandstone types of deposits uranium seems to have been dissolved by and transported in rather oxidized solutions, and deposited where these solutions encountered reducing agents such as carbon, sulfides, ferrous minerals and hydrocarbons. Granitic rocks abnormally enriched in uranium have apparently been the most common source for uranium in vein-type deposits. Oxidizing solutions have been derived either from the surface or from depth. Surface solutions saturated with atmospheric oxygen have frequently passed through red bed or clean sandstone conduits on their way to and from uranium source rocks. Deep solutions of non-surface origin have apparently become sufficiently oxidizing by passage through and equilibration with red beds. The common association of clean sandstones or red beds with uranium-rich granites in the vicinity of vein-type uranium deposits is probably not fortuitous, and areas where these rock types are found together are considered particularly favorable targets for uranium exploration

  7. Restoration of uranium solution mining deposits

    International Nuclear Information System (INIS)

    Devries, F.W.; Lawes, B.C.

    1982-01-01

    A process is provided for restoring an ore deposit after uranium solution mining using ammonium carbonate leaching solutions has ceased. The process involves flushing the deposit with an aqueous solution of a potassium salt during which potassium ions exchange with ammonium ions remaining in the deposit. The ammonium containing flushing solution is withdrawn from the deposit for disposal

  8. Understanding the spectrum of diesel injector deposits

    Energy Technology Data Exchange (ETDEWEB)

    Quigley, Robert; Barbour, Robert [Lubrizol Limited, Derby (United Kingdom); Arters, David; Bush, Jim [Lubrizol Corporation, Wickliffe, OH (United States)

    2013-06-01

    Understanding the origin of diesel fuel injector deposits used to be relatively simple; for the most part they were caused by the decomposition of fuel during the combustion process, were generally organic in nature and typically only affected the nozzle orifices. However, modem fuel injector designs appear to be both more severe in terms of generating conditions conducive to creating new and different types of deposits and more likely to have their operation affected by those deposits. Changes to fuel composition and type have in some cases increased the potential pool of reactive species or provided new potential deposit precursors. As a result, the universe of diesel injector deposits now range from the traditional organic to partially or fully inorganic in nature and from nozzle coking deposits to deposits which can seize the internal components of the injector; so called internal diesel injector deposits. Frequently, combinations of inorganic and organic deposits are found. While power loss is one well known issue associated with nozzle deposits, other field problems resulting from these new deposits include severe issues with drivability, emissions, fuel consumption and even engine failure. Conventional deposit control additive chemistries were developed to be effective against organic nozzle coking deposits. These conventional additives in many cases may prove ineffective against this wide range of deposit types. This paper discusses the range of deposits that have been found to adversely impact modem diesel fuel injectors and compares the performance of conventional and new, advanced deposit control additives against these various challenges to proper fuel injector functioning. (orig.)

  9. Restoration of uranium solution mining deposits

    Energy Technology Data Exchange (ETDEWEB)

    Devries, F.W.; Lawes, B.C.

    1982-01-19

    A process is provided for restoring an ore deposit after uranium solution mining using ammonium carbonate leaching solutions has ceased. The process involves flushing the deposit with an aqueous solution of a potassium salt during which potassium ions exchange with ammonium ions remaining in the deposit. The ammonium containing flushing solution is withdrawn from the deposit for disposal.

  10. Analysing the Cenozoic depositional record

    DEFF Research Database (Denmark)

    Goledowski, Bartosz; Clausen, O.R.; Nielsen, S.B.

    2008-01-01

    It is well known that sediment deposition in the North Sea and on the Norwegian Shelf varied significantly during the Cenozoic as a consequence of varying erosion rate mainly in Western Scandinavia, in Scotland and in the Alps. Recent results have demonstrated that a causal relationship exists...... of variations in erosion rates. Here we present the rationale behind the project, the data available and some preliminary results. The dense seismic and well coverage in the area makes it possible to estimate the rate of deposition of matrix mass. Assuming that sediment storage is not important, this provides...... models. The matrix mass deposition history will be compared with the paleoclimate record (e.g. oxygen isotope curves) to see if the previously observed correlation in the eastern North Sea can be extended to other ages and locations.  ...

  11. Surficial uranium deposits in Algeria

    International Nuclear Information System (INIS)

    Mokaddem, M.; Fuchs, Y.

    1984-01-01

    Along southern border of the Hoggar (Algeria) Precambrian shield, Lower Palaeozoic sediments lie unconformably on weathered metamorphic rocks. Along the eastern border of the Tin Seririne basin some good examples of the weathered rocks underneath the unconformity are exposed. The palaeosurface is a peneplain with only minor topographical reliefs from one to a few metres high. The nature and intensity of the weathering process was controlled by the topography, and the existence of badly drained areas is particularly important. At one such area the Tahaggart uranium ore deposit was discovered. The uranium ore consists mainly of torbernite and autunite. The deposit is present in the weathered gneiss underneath the palaeosurface. Mineralogical and geochemical observations indicated that the ore deposit was formed during the period of weathering which was controlled by climatological and palaeotopographical factors. (author)

  12. Sub-aerial tailings deposition

    International Nuclear Information System (INIS)

    Knight, R.B.; Haile, J.P.

    1984-01-01

    The sub-aerial technique involves the systematic deposition of tailings in thin layers and allowing each layer to settle, drain and partially air dry prior to covering with a further layer. Underdrainage produces densities in excess of those achieved by sub-aqueous deposition and any air-drying serves to preconsolidate each layer with a resulting further increase in density. The low permeability of the tailings surface resulting from this deposition technique results in high runoff coefficients and, by decanting the runoff component of direct precipitation, a net evaporation condition can be achieved even in high rainfall areas. An underdrainage system prevents the build-up of excess pore-pressures within the tailings mass and at decommissioning the tailings are fully consolidated and drained thereby eliminating the possibility of any long term seepage. This paper presents a general description of these design concepts, and details of two projects where the concepts have been applied

  13. Clinical variables serve as prognostic factors in a model for survival from glioblastoma multiforme: an observational study of a cohort of consecutive non-selected patients from a single institution

    International Nuclear Information System (INIS)

    Michaelsen, Signe Regner; Christensen, Ib Jarle; Grunnet, Kirsten; Stockhausen, Marie-Thérése; Broholm, Helle; Kosteljanetz, Michael; Poulsen, Hans Skovgaard

    2013-01-01

    Although implementation of temozolomide (TMZ) as a part of primary therapy for glioblastoma multiforme (GBM) has resulted in improved patient survival, the disease is still incurable. Previous studies have correlated various parameters to survival, although no single parameter has yet been identified. More studies and new approaches to identify the best and worst performing patients are therefore in great demand. This study examined 225 consecutive, non-selected GBM patients with performance status (PS) 0–2 receiving postoperative radiotherapy with concomitant and adjuvant TMZ as primary therapy. At relapse, patients with PS 0–2 were mostly treated by reoperation and/or combination with bevacizumab/irinotecan (BEV/IRI), while a few received TMZ therapy if the recurrence-free period was >6 months. Median overall survival and time to progression were 14.3 and 8.0 months, respectively. Second-line therapy indicated that reoperation and/or BEV/IRI increased patient survival compared with untreated patients and that BEV/IRI was more effective than reoperation alone. Patient age, ECOG PS, and use of corticosteroid therapy were significantly correlated with patient survival and disease progression on univariate analysis, whereas p53, epidermal growth factor receptor, and O 6 -methylguanine-DNA methyltransferase expression (all detected by immunohistochemistry), tumor size or multifocality, and extent of primary operation were not. A model based on age, ECOG PS, and corticosteroids use was able to predict survival probability for an individual patient. The survival of RT/TMZ-treated GBM patients can be predicted based on patient age, ECOG PS, and corticosteroid therapy status

  14. TULSA UNIVERSITY PARAFFIN DEPOSITION PROJECTS

    Energy Technology Data Exchange (ETDEWEB)

    Cem Sarica; Michael Volk

    2004-06-01

    As oil and gas production moves to deeper and colder water, subsea multiphase production systems become critical for economic feasibility. It will also become increasingly imperative to adequately identify the conditions for paraffin precipitation and predict paraffin deposition rates to optimize the design and operation of these multi-phase production systems. Although several oil companies have paraffin deposition predictive capabilities for single-phase oil flow, these predictive capabilities are not suitable for the multiphase flow conditions encountered in most flowlines and wellbores. For deepwater applications in the Gulf of Mexico, it is likely that multiphase production streams consisting of crude oil, produced water and gas will be transported in a single multiphase pipeline to minimize capital cost and complexity at the mudline. Existing single-phase (crude oil) paraffin deposition predictive tools are clearly inadequate to accurately design these pipelines, because they do not account for the second and third phases, namely, produced water and gas. The objective of this program is to utilize the current test facilities at The University of Tulsa, as well as member company expertise, to accomplish the following: enhance our understanding of paraffin deposition in single and two-phase (gas-oil) flows; conduct focused experiments to better understand various aspects of deposition physics; and, utilize knowledge gained from experimental modeling studies to enhance the computer programs developed in the previous JIP for predicting paraffin deposition in single and two-phase flow environments. These refined computer models will then be tested against field data from member company pipelines.

  15. Hereditary iron and copper deposition

    DEFF Research Database (Denmark)

    Aaseth, Jan; Flaten, Trond Peder; Andersen, Ole

    2007-01-01

    Hereditary deposition of iron (primary haemochromatosis) or copper (Wilson's disease) are autosomal recessive metabolic disease characterized by progressive liver pathology and subsequent involvement of various other organs. The prevalence of primary haemochromatosis is approximately 0.5%, about......, they may be inadequate in patients diagnosed so late that extensive body deposits of metal have been developed. The main research needs in this field are to further clarify molecular mechanisms of disease progression and to develop new chelators that are more effective and less toxic than those presently...

  16. Investigation on radioactivity of deposition

    International Nuclear Information System (INIS)

    Vaas, L.H.; Smetsers, R.C.G.M.; Mattern, F.C.M.; Drost, R.M.S. van; Ockhuizen, A.; Glastra, P.; Koolwijk, A.C.

    1990-04-01

    This report of the Dutch National Institute of Public Health and Environmental Protection (RIVM) summarizes the results of measurements of radionuclides deposited in the Netherlands in 1988. The samples of deposition were taken at Bilthoven, located near the center of the country. In 1988 measurements were carried out to determine the activities of γ-emitters, where 7 Be, 40 K, 134 Cs and 137 Cs were identified, and those of 3 H, 210 Pb and 210 Po. Also the gross α-, gross β- and gross γ-activities were determined. (author). 10 refs.; 7 figs.; 6 tabs

  17. Mathematical geology studies of deposit prospect types

    International Nuclear Information System (INIS)

    Liu Guangping

    1998-08-01

    Exact certainty prospect type of uranium deposit, not only can assure the quality of deposit prospects, but also increase economic benefits. Based on the standard of geological prospect of uranium deposit, the author introduces a method of Fuzzy Synthetical Comment for dividing prospect type of uranium deposit. The practical applications demonstrate that the regression accuracy, discriminated by Zadeh operator, of 15 known deposits is 100%

  18. Bank deposits, notions and features of accounting

    Directory of Open Access Journals (Sweden)

    Georgeta MELNIC

    2016-06-01

    Full Text Available Bank deposits are the main method of raising capital and short-term available savings. The opening and using of the bank deposits is the main function of banks. In 2004 the Deposit Guarantee Fund was set up in the Republic of Moldova of Deposit Guarantee Fund and for the first time there was established a guaranteed bank minimum in case of bank insolvency which is currently 6,000 lei for the deposit of each natural person.

  19. Características de las fallas en alimentadores de 13,8 kV del sistema soterrado de La Habana;Characteristic of 13,8 kV feeders faults of the Havana underground system

    Directory of Open Access Journals (Sweden)

    Boris Alba - Valle

    2011-06-01

    Full Text Available El sistema soterrado de La Habana enfrenta problemas de continuas fallas en sus alimentadores de 13,8 kV. En este trabajo se determinan las características de estas averías, en el período comprendido entre los años 2007 y 2009, y se proponen algunas medidas objetivas con el fin de contribuir a su disminución. La investigación se basó fundamentalmente en el estudio de la base de datos de los alimentadores de 13,8 kV proporcionada por el departamento técnico de la Unidad Empresarial Básica (UEB Soterrada y en el uso de herramientas estadísticas digitales. Como resultado se pudo constatar que las fallas son más frecuentes en los alimentadores de la subestación de Tallapiedra producto de la humedad en cables y empalmes con aislamiento de PILC (papel impregnado en aceite y con cubierta de plomo, dispuestos por tierra muerta. Finalmente, las medidas propuestas tuvieron un impacto positivo en la disminución de estas fallas, en un período inferior a un año.The Havana underground system has problems of continuous faults in their 13,8 kV feeders. In this article the characteristics of these mishaps in the period of 2007 to 2009 are determined and purpose some objective measurements with the end of contributing to their decrease. The investigation was fundamentally based on the study of the 13,8 kV feeders database proportioned by the technical department of the Underground Basic Managerial Unit (UEB and the use of digital statistical tools. As a result, it was verified that the faults occur with more frequency in the Tallapiedra substation feeders, due to the humidity in cables and connections with PILC isolation (impregnated in oil and lead covered paper, prepared for undergrounding directly in the earth. Finally, the proposed measures had a positive impact in the decrease of these faults, in a period less than to a year.

  20. Advanced deposition model for thermal activated chemical vapor deposition

    Science.gov (United States)

    Cai, Dang

    Thermal Activated Chemical Vapor Deposition (TACVD) is defined as the formation of a stable solid product on a heated substrate surface from chemical reactions and/or dissociation of gaseous reactants in an activated environment. It has become an essential process for producing solid film, bulk material, coating, fibers, powders and monolithic components. Global market of CVD products has reached multi billions dollars for each year. In the recent years CVD process has been extensively used to manufacture semiconductors and other electronic components such as polysilicon, AlN and GaN. Extensive research effort has been directed to improve deposition quality and throughput. To obtain fast and high quality deposition, operational conditions such as temperature, pressure, fluid velocity and species concentration and geometry conditions such as source-substrate distance need to be well controlled in a CVD system. This thesis will focus on design of CVD processes through understanding the transport and reaction phenomena in the growth reactor. Since the in situ monitor is almost impossible for CVD reactor, many industrial resources have been expended to determine the optimum design by semi-empirical methods and trial-and-error procedures. This approach has allowed the achievement of improvements in the deposition sequence, but begins to show its limitations, as this method cannot always fulfill the more and more stringent specifications of the industry. To resolve this problem, numerical simulation is widely used in studying the growth techniques. The difficulty of numerical simulation of TACVD crystal growth process lies in the simulation of gas phase and surface reactions, especially the latter one, due to the fact that very limited kinetic information is available in the open literature. In this thesis, an advanced deposition model was developed to study the multi-component fluid flow, homogeneous gas phase reactions inside the reactor chamber, heterogeneous surface

  1. Deposition and Resuspension of Particles

    DEFF Research Database (Denmark)

    Lengweiler, P.; Nielsen, Peter V.; Moser, A.

    To investigate the physical process of deposition and resuspension of particles in the indoor environment, scale experiments are used and a sampling method is established. The influences of surface orientation and turbulence and velocity of the air on the dust load on a surface are analysed....

  2. Cluster Implantation and Deposition Apparatus

    DEFF Research Database (Denmark)

    Hanif, Muhammad; Popok, Vladimir

    2015-01-01

    In the current report, a design and capabilities of a cluster implantation and deposition apparatus (CIDA) involving two different cluster sources are described. The clusters produced from gas precursors (Ar, N etc.) by PuCluS-2 can be used to study cluster ion implantation in order to develop...

  3. Deposition gradients across mangrove fringes

    NARCIS (Netherlands)

    Horstman, Erik Martijn; Mullarney, Julia C.; Bryan, K.R.; Sandwell, Dean R.; Aagaard, Troels; Deigaard, Rolf; Fuhrman, David

    2017-01-01

    Observations in a mangrove in the Whangapoua Harbour, New Zealand, have shown that deposition rates are greatest in the fringing zone between the tidal flats and the mangrove forest, where the vegetation is dominated by a cover of pneumatophores (i.e. pencil roots). Current speeds and suspended

  4. Uranium extraction from underground deposits

    International Nuclear Information System (INIS)

    Wolfe, C.R.

    1982-01-01

    Uranium is extracted from underground deposits by passing an aqueous oxidizing solution of carbon dioxide over the ore in the presence of calcium ions. Complex uranium carbonate or bicarbonate ions are formed which enter the solution. The solution is forced to the surface and the uranium removed from it

  5. Electrolytic nickel deposits upon uranium

    International Nuclear Information System (INIS)

    Baudin, G.; Chauvin, G.; Coriou, H.; Hure, J.

    1958-01-01

    The authors present a new possibility to protect uranium by very adherent nickel deposits got by aqueous medium electrolysis. Surface treatment of uranium is based upon the chemical etching method from Lietazke. After thermal treatments at 600, 700 and 800 deg. C, under vacuum, a good intermetallic U-Ni diffusion is observed for each case. (author) [fr

  6. IAEA Classification of Uranium Deposits

    International Nuclear Information System (INIS)

    Bruneton, Patrice

    2014-01-01

    Classifications of uranium deposits follow two general approaches, focusing on: • descriptive features such as the geotectonic position, the host rock type, the orebody morphology, …… : « geologic classification »; • or on genetic aspects: « genetic classification »

  7. Advances in energy deposition theory

    International Nuclear Information System (INIS)

    Paretzke, H.G.

    1980-01-01

    In light of the fields of radiation protection and dosimetric problems in medicine, advances in the area of microscopic target related studies are discussed. Energy deposition is discussed with emphasis upon track structures of electrons and heavy charged particles and track computer calculations

  8. Unconformity-related uranium deposits

    International Nuclear Information System (INIS)

    Ewers, G.R.; Ferguson, J.

    1985-01-01

    Documentation of ore deposit characterisation is being undertaken to assess the controls of uranium mineralisation associated with Proterozoic unconformities. The Turee Creek uranium prospect in Western Australia is associated with a faulted contact between the Middle Proterozoic Kunderong Sandstone and the Lower Proterozoic Wyloo Group

  9. Nitrogen deposition and terrestrial biodiversity

    Science.gov (United States)

    Christopher M. Clark; Yongfei Bai; William D. Bowman; Jane M. Cowles; Mark E. Fenn; Frank S. Gilliam; Gareth K. Phoenix; Ilyas Siddique; Carly J. Stevens; Harald U. Sverdrup; Heather L. Throop

    2013-01-01

    Nitrogen deposition, along with habitat losses and climate change, has been identified as a primary threat to biodiversity worldwide (Butchart et al., 2010; MEA, 2005; Sala et al., 2000). The source of this stressor to natural systems is generally twofold: burning of fossil fuels and the use of fertilizers in modern intensive agriculture. Each of these human...

  10. Electro-spark deposition technology

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, R.N. [Pacific Northwest National Lab., Richland, WA (United States)

    1997-12-01

    Electro-Spark Deposition (ESD) is a micro-welding process that uses short duration, high-current electrical pulses to deposit or alloy a consumable electrode material onto a metallic substrate. The ESD process was developed to produce coatings for use in severe environments where most other coatings fail. Because of the exceptional damage resistance of these coatings, and the versatility of the process to apply a wide variety of alloys, intermetallics, and cermets to metal surfaces, the ESD process has been designated critical to the life and economy of the advanced fossil energy systems as the higher temperatures and corrosive environments exceed the limits of known structural materials to accommodate the service conditions. Developments include producing iron aluminide-based coatings with triple the corrosion resistance of the best previous Fe{sub 3}Al coatings, coatings with refractory metal diffusion barriers and multi layer coatings for achieving functionally gradient properties between the substrate and the surface. A new development is the demonstration of advanced aluminide-based ESD coatings for erosion and wear applications. One of the most significant breakthroughs to occur in the last dozen years is the discovery of a process regime that yields an order of magnitude increase in deposition rates and achievable coating thicknesses. Achieving this regime has required the development of advanced ESD electronic capabilities. Development is now focused on further improvements in deposition rates, system reliability when operating at process extremes, and economic competitiveness.

  11. World distribution of uranium deposits

    Science.gov (United States)

    Fairclough, M. C.; Irvine, J. A.; Katona, L. F.; Simmon, W. L.; Bruneton, P.; Mihalasky, Mark J.; Cuney, M.; Aranha, M.; Pylypenko, O.; Poliakovska, K.

    2018-01-01

    Deposit data derived from IAEA UDEPO (http://infcis.iaea.org/UDEPO/About.cshtml) database with assistance from P. Bruneton (France) and M. Mihalasky (U.S.A.). The map is an updated companion to "World Distribution of Uranium Deposits (UDEPO) with Uranium Deposit Classification, IAEA Tech-Doc-1629". Geology was derived from L.B. Chorlton, Generalized Geology of the World, Geological Survey of Canada, Open File 5529 , 2007. Map production by M.C. Fairclough (IAEA), J.A. Irvine (Austrailia), L.F. Katona (Australia) and W.L. Slimmon (Canada). World Distribution of Uranium Deposits, International Atomic Energy Agency, Vienna, Austria. Cartographic Assistance was supplied by the Geological Survey of South Australia, the Saskatchewan Geological Survey and United States Geological Survey to the IAEA. Coastlines, drainage, and country boundaries were obtained from ArcMap, 1:25 000 000 scale, and are copyrighted data containing the intellectual property of Environmental Systems Research Institute (ESRI). The use of particular designations of countries or territories does not imply any judgment by the publisher, the IAEA, as to the legal status of such countries or territories, of their authorities and institutions or of the delimitation of their boundaries. Any revisions or additional geological information known to the user would be welcomed by the International Atomic Energy Agency and the Geological Survey of Canada.

  12. Deposit competition and loan markets

    NARCIS (Netherlands)

    Arping, S.

    Less-intense competition for deposits, by mitigating banks’ incentive to take excessive risks, is traditionally believed to lead to lower non-performing loan (NPL) ratios and more-stable banks. This paper revisits this proposition in a model with borrower moral hazard in which banks’ NPL ratios

  13. The uranium deposits of Ontario

    International Nuclear Information System (INIS)

    Robertson, J.A.

    1981-01-01

    The principal types of uranium deposits in Ontario are carbonatites and fenites, alkalic volcanic rocks, pegiatites, calc-silicate rocks, pyritic quartz-pebble conglomerates, polymictic conglomerates and some pelitic rocks, and various 'pitchblende' deposits including late Precambrian unconformities, possibly late Precambrian diabase dikes, and other unconformities: carbonates, sandstones, lignites, and semi-pelitic rocks of middle and upper Precambrian age. Only red unzoned pegmatite and the pyritic quartz-pebble conglomerate have supported production. Ontario reasonably assured and estimated resources in the economic and subeconomic categories in 1977 amounted to 553 000 tonnes U, and 1977 production was 4000 tonnes U. Measured, indicated, and inferred resources in the Elliot Lake - Agnew Lake area are at least 400 000 tonnes U. The latter deposits are also a significant thorium resource. Geological features reflecting major changes in physics and chemistry are prime controls on distribution of uranium deposits. Geological province and subprovince boundaries, major faults, higher metamorphic grades, domain boundaries related to quartz monzonite batholiths, alkalic complexes, and the distribution of carbonate rocks are examples of such geological features

  14. Persisting roughness when deposition stops.

    Science.gov (United States)

    Schwartz, Moshe; Edwards, S F

    2004-12-01

    Useful theories for growth of surfaces under random deposition of material have been developed by several authors. The simplest theory is that introduced by Edwards and Wilkinson (EW), which is linear and soluble. Its nonlinear generalization by Kardar, Parisi, and Zhang (KPZ) resulted in many subsequent studies. Yet both EW and KPZ theories contain an unphysical feature. When deposition of material is stopped, both theories predict that as time tends to infinity, the surface becomes flat. In fact, of course, the final surface is not flat, but simply has no gradients larger than the gradient related to the angle of repose. We modify the EW and KPZ theories to accommodate this feature and study the consequences for the simpler system which is a modification of the EW equation. In spite of the fact that the equation describing the evolution of the surface is not linear, we find that the steady state in the presence of noise is not very different in the long-wavelength limit from that of the linear EW equation. The situation is quite different from that of EW when deposition stops. Initially there is still some rearrangement of the surface, but that stops as everywhere on the surface the gradient is less than that related to the angle of repose. The most interesting feature observed after deposition stops is the emergence of history-dependent steady-state distributions.

  15. Discharge cleaning of carbon deposits

    International Nuclear Information System (INIS)

    Mozetic, M.; Vesel, A.; Drenik, A.

    2006-01-01

    Experimental results of discharge cleaning of carbon deposits are presented. Deposits were prepared by creating plasma in pure methane. The methane was cracked in RF discharge at the output power of 250 W. The resultant radicals were bonded to the wall of discharge vessel forming a thin film of hydrogenated black carbon with the thickness of about 200nm. The film was then cleaned in situ by oxygen plasma with the density of about 1x10 16 m -3 , electron temperature of 5 eV, neutral gas kinetic temperature of about 100 0 C and neutral atom density of 6x10 21 m -3 . The treatment time was 30 minutes. The efficiency of plasma cleaning was monitored by optical emission spectroscopy. As long as the wall was contaminated with carbon deposit, substantial emission of the CO molecules was detected. As the cleaning was in progress, the CO emission was decreasing and vanished after 30 minutes when the discharge vessel became free of any carbon. The results are explained by interaction of plasma radicals with carbon deposits. (author)

  16. Improving deposition tester to study adherent deposits in papermaking

    OpenAIRE

    Monte Lara, Concepción; Sánchez, Mónica; Blanco Suárez, Ángeles; Negro Álvarez, Carlos; Tijero Miquel, Julio

    2012-01-01

    Conventional methods used for the quantification of adherent material contained in a pulp suspension propose either filtration of the sample, which may lead to loss of sticky material in the filtrate, or dilution of the pulp, which may cause destabilization of the dissolved and colloidal material; thus, leading to unreliable results. In 1998, the Cellulose and Paper Group of University Complutense of Madrid developed a deposition tester which aimed to quantify the adherence of material (micro...

  17. Constructing deposition chronologies for peat deposits using radiocarbon dating

    Directory of Open Access Journals (Sweden)

    N. Piotrowska

    2011-06-01

    Full Text Available Radiocarbon dating is one of the main methods used to establish peat chronologies. This article reviews the basis of the method and its application to dating of peat deposits. Important steps in the radiocarbon dating procedure are described, including selection and extraction of material (and fractions for dating, chemical and physical preparation of media suitable for measurements, measurements of 14C activity or concentration, calculations, calibration of results and age-depth modelling.

  18. Cultivation and irradiation of human fibroblasts in a medium enriched with platelet lysate for obtaining feeder layer in epidermal cell culture; Cultivo e irradiacao de fibroblastos humanos em meio enriquecido com lisado de plaquetas para obtencao de camada de sustentacao em culturas de celulas da epiderme

    Energy Technology Data Exchange (ETDEWEB)

    Yoshito, Daniele

    2011-07-01

    For over 30 years, the use of culture medium, enriched with bovine serum, and murines fibroblasts, with the rate of proliferation controlled by irradiation or by share anticarcinogenic drugs, has been playing successfully its role in assisting in the development of keratinocytes in culture, for clinical purposes. However, currently there is a growing concern about the possibility of transmitting prions and animals viruses to transplanted patients. Taking into account this concern, the present work aims to cultivate human fibroblasts in a medium enriched with human platelets lysate and determine the irradiation dose of these cells, for obtaining feeder layer in epidermal cell culture. For carrying out the proposed objective, platelets lysis has standardized, this lysate was used for human fibroblasts cultivation and the irradiation dose enough to inhibit its duplication was evaluated. Human keratinocytes were cultivated in these feeder layers, in culture medium enriched with the lysate. With these results we conclude that the 10% platelets lysate promoted a better adhesion and proliferation of human fibroblasts and in all dose levels tested (60 to 300 Gy), these had their mitotic activity inactivated by ionizing irradiation, being that the feeder layers obtained with doses from 70 to 150 Gy were those that provided the best development of keratinocytes in medium containing 2.5% of human platelet lysate. Therefore, it was possible to standardize both the cultivation of human fibroblasts as its inactivation for use as feeder layer in culture of keratinocytes, so as to eliminate xenobiotics components. (author)

  19. Vapor deposition of tantalum and tantalum compounds

    International Nuclear Information System (INIS)

    Trkula, M.

    1996-01-01

    Tantalum, and many of its compounds, can be deposited as coatings with techniques ranging from pure, thermal chemical vapor deposition to pure physical vapor deposition. This review concentrates on chemical vapor deposition techniques. The paper takes a historical approach. The authors review classical, metal halide-based techniques and current techniques for tantalum chemical vapor deposition. The advantages and limitations of the techniques will be compared. The need for new lower temperature processes and hence new precursor chemicals will be examined and explained. In the last section, they add some speculation as to possible new, low-temperature precursors for tantalum chemical vapor deposition

  20. Adhesion Strength of Biomass Ash Deposits

    DEFF Research Database (Denmark)

    Laxminarayan, Yashasvi; Jensen, Peter Arendt; Wu, Hao

    2016-01-01

    . Therefore, timely removal of ash deposits is essential for optimal boiler operation. In order to improve the qualitative and quantitative understanding of deposit shedding in boilers, this study investigates the shear adhesion strength of biomass ash deposits on superheater tubes. Artificial biomass ash...... deposits were prepared on superheater tubes and sintered in an oven at temperatures up to 1000 °C. Subsequently, the deposits were sheared off by an electrically controlled arm, and the corresponding adhesion strength was measured. The results reveal the effect of temperature, ash/deposit composition......, sintering duration, and steel type on the adhesion strength....

  1. Mitogenomes of Giant-Skipper Butterflies reveal an ancient split between deep and shallow root feeders [version 1; referees: 2 approved

    Directory of Open Access Journals (Sweden)

    Jing Zhang

    2017-03-01

    Full Text Available Background: Giant-Skipper butterflies from the genus Megathymus are North American endemics. These large and thick-bodied Skippers resemble moths and are unique in their life cycles. Grub-like at the later stages of development, caterpillars of these species feed and live inside yucca roots. Adults do not feed and are mostly local, not straying far from the patches of yucca plants. Methods: Pieces of muscle were dissected from the thorax of specimens and genomic DNA was extracted (also from the abdomen of a specimen collected nearly 60 years ago. Paired-end libraries were prepared and sequenced for 150bp from both ends. The mitogenomes were assembled from the reads followed by a manual gap-closing procedure and a phylogenetic tree was constructed using a maximum likelihood method from an alignment of the mitogenomes. Results: We determined mitogenome sequences of nominal subspecies of all five known species of Megathymus and Agathymus mariae to confidently root the phylogenetic tree. Pairwise sequence identity indicates the high similarity, ranging from 88-96% among coding regions for 13 proteins, 22 tRNAs and 2 rRNA, with a gene order typical for mitogenomes of Lepidoptera. Phylogenetic analysis confirms that Giant-Skippers (Megathymini originate within the subfamily Hesperiinae and do not warrant a subfamily rank. Genus Megathymus is monophyletic and splits into two species groups. M. streckeri and M. cofaqui caterpillars feed deep in the main root system of yucca plants and deposit frass underground. M. ursus, M. beulahae and M. yuccae feed in the yucca caudex and roots near the ground, and deposit frass outside through a "tent" (a silk tube projecting from the center of yucca plant. M. yuccae and M. beulahae are sister species consistently with morphological similarities between them. Conclusions: We constructed the first DNA-based phylogeny of the genus Megathymus from their mitogenomes. The phylogeny agrees with morphological

  2. Dust deposit in recirculation regions

    International Nuclear Information System (INIS)

    Griemert, R.

    1985-03-01

    The present report shows investigations, which have been carried out in a closed duct at forward and backward facing steps. Distribution of fluid velocity and fluid fluctuations in and normal to main flow direction as well as the distribution of Reynolds shear stress have been measured. The mass transfer downstream of a backward facing step has been investigated as well. By using graphite-, copper-, tin- and rubber dust, conditions of deposition have been defined experimentally. A serie of photos shows the filling of a recirculation region downstream of a backward facing step with graphite dust. The present investigations allow to avoid deposition of dust in recirculation regions by selecting the fluid numbers in an appropriate way. (orig.) [de

  3. High throughput semiconductor deposition system

    Science.gov (United States)

    Young, David L.; Ptak, Aaron Joseph; Kuech, Thomas F.; Schulte, Kevin; Simon, John D.

    2017-11-21

    A reactor for growing or depositing semiconductor films or devices. The reactor may be designed for inline production of III-V materials grown by hydride vapor phase epitaxy (HVPE). The operating principles of the HVPE reactor can be used to provide a completely or partially inline reactor for many different materials. An exemplary design of the reactor is shown in the attached drawings. In some instances, all or many of the pieces of the reactor formed of quartz, such as welded quartz tubing, while other reactors are made from metal with appropriate corrosion resistant coatings such as quartz or other materials, e.g., corrosion resistant material, or stainless steel tubing or pipes may be used with a corrosion resistant material useful with HVPE-type reactants and gases. Using HVPE in the reactor allows use of lower-cost precursors at higher deposition rates such as in the range of 1 to 5 .mu.m/minute.

  4. The unending deposit insurance mess.

    Science.gov (United States)

    Kane, E J

    1989-10-27

    The thrift institution deposit insurance mess is rooted in defects in political and bureaucratic accountability. Under existing incentives, covering up evidence of poor regulatory performance and relaxing binding capital requirements are rational governmental responses to widespread industry insolvency. Similarly, aggressive industry risk taking is a rational response by thrift managers to regulatory forbearances. Far from acknowledging these incentive defects, the Bush plan for cleaning up the mess adopts theories that spotlight other causes: specifically, poor thrift management and the deregulation of thrift institution activities and of deposit interest rates. To end the mess, politicians and regulators must jettison these comfortable theories and surrender discretion that permits them to finesse the need to budget for governmental financial commitments.

  5. Geological aspects of acid deposition

    International Nuclear Information System (INIS)

    Bricker, O.P.

    1984-01-01

    The general pattern of rain falling on the earth and reacting with the materials of the lithosphere (the weathering reactions so familiar to every beginning geology student) began soon after the earth was formed and has continued to the present. Anthropogenic additions to the natural acidic components of the atmosphere have increased since the time of the industrial revolution until they now rival or exceed those of the natural system. The severity of the environmental perturbations caused by these anthropogenic additions to the atmosphere has become a hotly debated topic in scientific forums and in the political arena. The six chapters in this book address various aspects of the acid deposition phenomenon from a geological perspective. It is hoped that the geological approach will be useful in bringing the problem more clearly into focus and may shed light on the geochemical processes that modify the chemical composition of acid deposition after it encounters and reacts with the materials of the lithosphere

  6. Local deposition of high-purity Pt nanostructures by combining electron beam induced deposition and atomic layer deposition

    NARCIS (Netherlands)

    Mackus, A.J.M.; Mulders, J.J.L.; Sanden, van de M.C.M.; Kessels, W.M.M.

    2010-01-01

    An approach for direct-write fabrication of high-purity platinum nanostructures has been developed by combining nanoscale lateral patterning by electron beam induced deposition (EBID) with area-selective deposition of high quality material by atomic layer deposition (ALD). Because virtually pure,

  7. Pele Plume Deposit on Io

    Science.gov (United States)

    1997-01-01

    The varied effects of Ionian volcanism can be seen in this false color infrared composite image of Io's trailing hemisphere. Low resolution color data from Galileo's first orbit (June, 1996) have been combined with a higher resolution clear filter picture taken on the third orbit (November, 1996) of the spacecraft around Jupiter.A diffuse ring of bright red material encircles Pele, the site of an ongoing, high velocity volcanic eruption. Pele's plume is nearly invisible, except in back-lit photographs, but its deposits indicate energetic ejection of sulfurous materials out to distances more than 600 kilometers from the central vent. Another bright red deposit lies adjacent to Marduk, also a currently active ediface. High temperature hot spots have been detected at both these locations, due to the eruption of molten material in lava flows or lava lakes. Bright red deposits on Io darken and disappear within years or decades of deposition, so the presence of bright red materials marks the sites of recent volcanism.This composite was created from data obtained by the Solid State Imaging (CCD) system aboard NASA's Galileo spacecraft. The region imaged is centered on 15 degrees South, 224 degrees West, and is almost 2400 kilometers across. The finest details that can be discerned in this picture are about 3 kilometers across. North is towards the top of the picture and the sun illuminates the surface from the west.The Jet Propulsion Laboratory, Pasadena, CA manages the mission for NASA's Office of Space Science, Washington, DC.This image and other images and data received from Galileo are posted on the World Wide Web, on the Galileo mission home page at URL http://galileo.jpl.nasa.gov. Background information and educational context for the images can be found at URL http://www.jpl.nasa.gov/galileo/sepo

  8. Complexing and hydrothermal ore deposition

    CERN Document Server

    Helgeson, Harold C

    1964-01-01

    Complexing and Hydrothermal Ore Deposition provides a synthesis of fact, theory, and interpretative speculation on hydrothermal ore-forming solutions. This book summarizes information and theory of the internal chemistry of aqueous electrolyte solutions accumulated in previous years. The scope of the discussion is limited to those aspects of particular interest to the geologist working on the problem of hydrothermal ore genesis. Wherever feasible, fundamental principles are reviewed. Portions of this text are devoted to calculations of specific hydrothermal equilibriums in multicompone

  9. Modular plants for small deposits

    International Nuclear Information System (INIS)

    Josa, J.M.; Moral, A.; Otero, J.L.; Suarez, E.

    1985-01-01

    The large investment required to recover uranium from small deposits is the greatest obstacle to their economic development. Various concepts (caravan mill, pure mill or semimobile mill) have been elaborated in different countries. Studies have also been made in Spain to develop a simple and economic flowsheet suitable for the beneficiation of small uranium deposits. An acid heap-leaching and solvent extraction process was chosen because there is already a great deal of experience of it in Spain. Modifications were necessary to make the equipment easy to transport and also to have a low and reusable investment when this flowsheet is used for small deposits. The aim was to develop a modular plant with all the elements fitted in compact units that needs little site preparation and little time and effort to connect the units. A standard small portable crushing plant can be borrowed and the mining operation and heap construction can be put to contract. There is a solvent extraction unit (150 m 3 /d) in continuous operation (24 h/d) and concentrate precipitation and handling facilities. The whole of the equipment is standard and as light as possible. Little civil engineering is required and the erection of the plant only needs a few months. The uranium capacity of these modular plants is between 35 and 50 t U 3 O 8 /a. Special consideration has been paid to regulations and the environmental aspects. (author)

  10. Uranium deposits obtention for fission chambers

    International Nuclear Information System (INIS)

    Artacho Saviron, E.

    1972-01-01

    The obtention of uranium deposits of the required quality for small cylindrical fission chambers presents some difficulties. With the method of electroplating here described the uniformity, reproducibility and adherence of the obtained deposits were satisfactory. (Author) 6 refs

  11. Federal Deposit Insurance Corporation (FDIC) Insured Banks

    Data.gov (United States)

    Department of Homeland Security — The Summary of Deposits (SOD) is the annual survey of branch office deposits for all FDIC-insured institutions including insured U.S. branches of foreign banks. Data...

  12. Acidic deposition and global climate change

    International Nuclear Information System (INIS)

    Nikolaidis, N.P.; Ecsedy, C.; Olem, H.; Nikolaidis, V.S.

    1990-01-01

    A literature is presented which examines the research published on understanding ecosystem acidification and the effects of acidic deposition on freshwaters. Topics of discussion include the following: acidic deposition; regional assessments; atmospheric deposition and transport; aquatic effects; mathematical modeling; liming acidic waters; global climate change; atmospheric changes; climate feedbacks; and aquatic effects

  13. 42 CFR 422.388 - Deposits.

    Science.gov (United States)

    2010-10-01

    ... to CMS. (2) The deposit must at all times have a fair market value of an amount that is 120 percent... is made; (2) The fair market value exceeds the amount of the required deposit; or (3) The required... PROGRAM MEDICARE ADVANTAGE PROGRAM Provider-Sponsored Organizations § 422.388 Deposits. (a) Insolvency...

  14. 19 CFR 210.28 - Depositions.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Depositions. 210.28 Section 210.28 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Discovery and Compulsory Process § 210.28 Depositions. (a) When depositions may be...

  15. 47 CFR 32.4040 - Customers' deposits.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Customers' deposits. 32.4040 Section 32.4040... FOR TELECOMMUNICATIONS COMPANIES Instructions for Balance Sheet Accounts § 32.4040 Customers' deposits. (a) This account shall include the amount of cash deposited with the company by customers as security...

  16. Dry deposition of particles to ocean surfaces

    NARCIS (Netherlands)

    Larsen, S.E.; Edson, J.B.; Hummelshoj, P.; Jensen, N.O.; Leeuw, G. de; Mestayer, P.G.

    1995-01-01

    Dry deposition of atmospheric particles mainly depends on wind speed and particle diameter. The dry deposition velocity, Vd, is found to vary by a factor of 100-1,000 with diameter in a likely diameter range, adding uncertainty to deposition estimates, because the diameter distribution for many

  17. European wet deposition maps based on measurements

    NARCIS (Netherlands)

    Leeuwen EP van; Erisman JW; Draaijers GPJ; Potma CJM; Pul WAJ van; LLO

    1995-01-01

    To date, wet deposition maps on a European scale have been based on long-range transport model results. For most components wet deposition maps based on measurements are only available on national scales. Wet deposition maps of acidifying components and base cations based on measurements are needed

  18. Low-pressure chemical vapor deposition as a tool for deposition of thin film battery materials

    NARCIS (Netherlands)

    Oudenhoven, J.F.M.; Dongen, van T.; Niessen, R.A.H.; Croon, de M.H.J.M.; Notten, P.H.L.

    2009-01-01

    Low Pressure Chemical Vapor Deposition was utilized for the deposition of LiCoO2 cathode materials for all-solid-state thin-film micro-batteries. To obtain insight in the deposition process, the most important process parameters were optimized for the deposition of crystalline electrode films on

  19. Dual Nitrate Isotopes in Dry Deposition: Utility for Partitioning Nox Source Contributions to Landscape Nitrogen Deposition

    Science.gov (United States)

    Dry deposition is a major component of total nitrogen deposition and thus an important source of bioavailable nitrogen to ecosystems. However, relative to wet deposition, less is known regarding the sources and spatial variability of dry deposition. This is in part due to diffi...

  20. Towards a genetic classification of uranium deposits

    International Nuclear Information System (INIS)

    Cuney, M.

    2009-01-01

    As the IAEA's uranium deposit classification is based on the deposit nature and morphology, some deposits which have been formed by very different genetic processes and located in very different geological environments, are grouped according to this classification. In order to build up a reliable genetic classification based on the mechanism at the origin of the formation of the deposit, the author presents the five main categories according to which uranium deposits can be classified: magmatic, hydrothermal, evapotranspiration, syn-sedimentary, and infiltration of meteoric water