Shot-noise-limited optical Faraday polarimetry with enhanced laser noise cancelling

International Nuclear Information System (INIS)

Li, Jiaming; Luo, Le; Carvell, Jeff; Cheng, Ruihua; Lai, Tianshu; Wang, Zixin

2014-01-01

We present a shot-noise-limited measurement of optical Faraday rotations with sub-ten-nanoradian angular sensitivity. This extremely high sensitivity is achieved by using electronic laser noise cancelling and phase sensitive detection. Specially, an electronic laser noise canceller with a common mode rejection ratio of over 100 dB was designed and built for enhanced laser noise cancelling. By measuring the Faraday rotation of ambient air, we demonstrate an angular sensitivity of up to 9.0×10 −9  rad/√(Hz), which is limited only by the shot-noise of the photocurrent of the detector. To date, this is the highest angular sensitivity ever reported for Faraday polarimeters in the absence of cavity enhancement. The measured Verdet constant of ambient air, 1.93(3)×10 −9 rad/(G cm) at 633 nm wavelength, agrees extremely well with the earlier experiments using high finesse optical cavities. Further, we demonstrate the applications of this sensitive technique in materials science by measuring the Faraday effect of an ultrathin iron film

Development of a Voice Activity Controlled Noise Canceller

Science.gov (United States)

Abid Noor, Ali O.; Samad, Salina Abdul; Hussain, Aini

2012-01-01

In this paper, a variable threshold voice activity detector (VAD) is developed to control the operation of a two-sensor adaptive noise canceller (ANC). The VAD prohibits the reference input of the ANC from containing some strength of actual speech signal during adaptation periods. The novelty of this approach resides in using the residual output from the noise canceller to control the decisions made by the VAD. Thresholds of full-band energy and zero-crossing features are adjusted according to the residual output of the adaptive filter. Performance evaluation of the proposed approach is quoted in terms of signal to noise ratio improvements as well mean square error (MSE) convergence of the ANC. The new approach showed an improved noise cancellation performance when tested under several types of environmental noise. Furthermore, the computational power of the adaptive process is reduced since the output of the adaptive filter is efficiently calculated only during non-speech periods. PMID:22778667

Development of a Voice Activity Controlled Noise Canceller

Directory of Open Access Journals (Sweden)

Aini Hussain

2012-05-01

Full Text Available In this paper, a variable threshold voice activity detector (VAD is developed to control the operation of a two-sensor adaptive noise canceller (ANC. The VAD prohibits the reference input of the ANC from containing some strength of actual speech signal during adaptation periods. The novelty of this approach resides in using the residual output from the noise canceller to control the decisions made by the VAD. Thresholds of full-band energy and zero-crossing features are adjusted according to the residual output of the adaptive filter. Performance evaluation of the proposed approach is quoted in terms of signal to noise ratio improvements as well mean square error (MSE convergence of the ANC. The new approach showed an improved noise cancellation performance when tested under several types of environmental noise. Furthermore, the computational power of the adaptive process is reduced since the output of the adaptive filter is efficiently calculated only during non-speech periods.

Active microphonic noise cancellation in radiation detectors

International Nuclear Information System (INIS)

Zimmermann, Sergio

2013-01-01

A new adaptive filtering technique to reduce microphonic noise in radiation detectors is presented. The technique is based on system identification that actively cancels the microphonic noise. A sensor is used to measures mechanical disturbances that cause vibration on the detector assembly, and the digital adaptive filtering estimates the impact of these disturbances on the microphonic noise. The noise then can be subtracted from the actual detector measurement. In this paper the technique is presented and simulations are used to support this approach. -- Highlights: •A sensor is used to measures mechanical disturbances that cause vibration on the detector assembly. •Digital adaptive filtering estimates the impact of these disturbances on the microphonic noise. •The noise is then subtracted from the actual detector measurement. •We use simulations to demonstrate the performance of this approach. •After cancellation, we recover most of the original energy resolution

Active noise canceling system for mechanically cooled germanium radiation detectors

Science.gov (United States)

Nelson, Karl Einar; Burks, Morgan T

2014-04-22

A microphonics noise cancellation system and method for improving the energy resolution for mechanically cooled high-purity Germanium (HPGe) detector systems. A classical adaptive noise canceling digital processing system using an adaptive predictor is used in an MCA to attenuate the microphonics noise source making the system more deployable.

An inductorless wideband LNA with a new noise canceling technique

OpenAIRE

MOGHADAM, POURIA PAZHOUHESH; ABRISHAMIFAR, ADIB

2017-01-01

An inductorless wideband low-noise amplifier (LNA) employing a new noise canceling technique for multistandard applications is presented. The main amplifier has a cascode common gate structure, which provides good input impedance matching and isolation. The proposed noise canceling technique not only improves the noise figure and power gain but also embeds a g$_{m}$-boosting technique in itself, which reduces the power consumption of the main amplifier. Using current-steering and ...

An improved probe noise approach for acoustic feedback cancellation

DEFF Research Database (Denmark)

Guo, Meng; Jensen, Søren Holdt; Jensen, Jesper

2012-01-01

The perhaps most challenging problem in acoustic feedback cancellation using adaptive filters is the bias problem. It is well-known that a probe noise approach can effectively prevent this problem. However, when the probe noise must be inaudible and the steady-state error of the adaptive filter...... expressions for its system behavior, and through a simulation experiment in an acoustic feedback cancellation system....

Effect of Filters on the Noise Generated by Continuous Positive Airway Pressure Delivered via a Helmet

Directory of Open Access Journals (Sweden)

Ricardo Hernández-Molina

2017-01-01

Full Text Available Introduction: One of the problems that the delivery of continuous positive airway pressure (CPAP via a helmet poses is the generation of noise. The objective of our study was to assess the effect that the use of filter has on sound pressure levels generated by the delivery of positive airway pressure at different gas flow rates. Materials and Methods: Sound pressure levels generated by neonatal helmet CPAP delivery were measured at different gas flows (20, 30, and 40 l/min with and without a breathing filter. Noise intensity was measured by installing microphones in the inner ear of dummy heads wearing helmets. Results: The sound pressure level increased by 38% at a gas flow of 40 l/min, as compared to a gas flow of 20 l/min {74 dBA [interquartile range (IQR 2,2] vs 52 dBA (IQR 5,9, respectively}. Using the breathing filter as a diffuser has a variety of effects on sound pressure levels according to the gas flow rate. Conclusion: The intensity of the noise generated by helmet delivery of positive airway pressure depends on the type of helmet used, gas flow, and use or not of a diffuser filter. Breathing filters with gas flows over 30 l/min might not be recommended since they would not attenuate but will rather amplify sound pressure.

Investigation of Diesel’s Residual Noise on Predictive Vehicles Noise Cancelling using LMS Adaptive Algorithm

Science.gov (United States)

Arttini Dwi Prasetyowati, Sri; Susanto, Adhi; Widihastuti, Ida

2017-04-01

Every noise problems require different solution. In this research, the noise that must be cancelled comes from roadway. Least Mean Square (LMS) adaptive is one of the algorithm that can be used to cancel that noise. Residual noise always appears and could not be erased completely. This research aims to know the characteristic of residual noise from vehicle’s noise and analysis so that it is no longer appearing as a problem. LMS algorithm was used to predict the vehicle’s noise and minimize the error. The distribution of the residual noise could be observed to determine the specificity of the residual noise. The statistic of the residual noise close to normal distribution with = 0,0435, = 1,13 and the autocorrelation of the residual noise forming impulse. As a conclusion the residual noise is insignificant.

A method of background noise cancellation for SQUID applications

International Nuclear Information System (INIS)

He, D F; Yoshizawa, M

2003-01-01

When superconducting quantum inference devices (SQUIDs) operate in low-cost shielding or unshielded environments, the environmental background noise should be reduced to increase the signal-to-noise ratio. In this paper we present a background noise cancellation method based on a spectral subtraction algorithm. We first measure the background noise and estimate the noise spectrum using fast Fourier transform (FFT), then we subtract the spectrum of background noise from that of the observed noisy signal and the signal can be reconstructed by inverse FFT of the subtracted spectrum. With this method, the background noise, especially stationary inferences, can be suppressed well and the signal-to-noise ratio can be increased. Using high-T C radio-frequency SQUID gradiometer and magnetometer, we have measured the magnetic field produced by a watch, which was placed 35 cm under a SQUID. After noise cancellation, the signal-to-noise ratio could be greatly increased. We also used this method to eliminate the vibration noise of a cryocooler SQUID

A study on the method for cancelling the background noise of the impact signal

International Nuclear Information System (INIS)

Kim, J. S.; Ham, C. S.; Park, J. H.

1998-01-01

In this paper, we compared the noise canceller (time domain analysis method) to the spectral subtraction (frequency domain analysis method) for cancelling background noise when the Loose Part Monitoring System's accelerometers combined the noise signal with the impact signal if the impact signal exists. In the operation of a nuclear power plant monitoring, alarm triggering occurs due to a peak signal in the background noise, an amplitude increase by component operation such as control rod movement or abrupt pump operation. This operation causes the background noise in LPMS. Thus this noise inputs to LPMS together with the impact signal. In case that this noise amplitude is very large comparing to that of the impact signal, we may not analyze the impact position and mass estimation. We analyzed two methods for cancelling background noise. First, we evaluate the signal to noise ratio utilizing the noise canceller. Second, we evaluate the signal to noise ratio utilizing the spectral subtraction. The evaluation resulted superior the noise canceller to the spectral subtraction on the signal to noise ratio

Thermal Noise Canceling in LNAs : A Review

NARCIS (Netherlands)

Nauta, Bram; Klumperink, Eric A.M.; Bruccoleri, Frederico

2004-01-01

Most wide-band amplifiers suffer from a fundamental trade-off between noise figure NF and source impedance matching, which limits NF to values typically above 3dB. Recently, a feed-forward noise canceling technique has been proposed to break this trade-off. This paper reviews the principle of the

Amplifiers Exploiting Thermal Noise Canceling: A Review

NARCIS (Netherlands)

Klumperink, Eric A.M.; Bruccoleri, F.; Stroet, P.M.; Stroet, Peter; Nauta, Bram

2004-01-01

Wide-band LNAs suffer from a fundamental trade-off between noise figure NF and source impedance matching, which limits NF to values typically above 3dB. Recently, a feed-forward noise canceling technique has been proposed to break this trade-off. This paper reviews the principle of the technique and

Analysis, Design, and Evaluation of Acoustic Feedback Cancellation Systems for Hearing Aids

DEFF Research Database (Denmark)

Guo, Meng

2013-01-01

Acoustic feedback problems occur when the output loudspeaker signal of an audio system is partly returned to the input microphone via an acoustic coupling through the air. This problem often causes significant performance degradations in applications such as public address systems and hearing aids....... In the worst case, the audio system becomes unstable and howling occurs. In this work, first we analyze a general multiple microphone audio processing system, where a cancellation system using adaptive filters is used to cancel the effect of acoustic feedback. We introduce and derive an accurate approximation...... in acoustic feedback cancellation for hearing aids. It utilizes a probe noise signal which is generated with a specific characteristic so that it can facilitate an unbiased adaptive filter estimation with fast tracking of feedback path variations/changes despite its low signal level. We show in a hearing aid...

A computer simulation of an adaptive noise canceler with a single input

Science.gov (United States)

Albert, Stuart D.

1991-06-01

A description of an adaptive noise canceler using Widrows' LMS algorithm is presented. A computer simulation of canceler performance (adaptive convergence time and frequency transfer function) was written for use as a design tool. The simulations, assumptions, and input parameters are described in detail. The simulation is used in a design example to predict the performance of an adaptive noise canceler in the simultaneous presence of both strong and weak narrow-band signals (a cosited frequency hopping radio scenario). On the basis of the simulation results, it is concluded that the simulation is suitable for use as an adaptive noise canceler design tool; i.e., it can be used to evaluate the effect of design parameter changes on canceler performance.

Multi-Stage Adaptive Noise Cancellation Technique for Synthetic Hard-α Inclusion

International Nuclear Information System (INIS)

Kim, Jae Joon

2003-01-01

Adaptive noise cancellation techniques are ideally suitable for reducing spatially varying noise due to the grain structure of material in ultrasonic nondestructive evaluation. Grain noises have an un-correlation property, while flaw echoes are correlated. Thus, adaptive filtering algorithms use the correlation properties of signals to enhance the signal-to-noise ratio (SNR) of the output signal. In this paper, a multi-stage adaptive noise cancellation (MANC) method using adaptive least mean square error (LMSE) filter for enhancing flaw detection in ultrasonic signals is proposed

Integration of Bass Enhancement and Active Noise Control System in Automobile Cabin

Directory of Open Access Journals (Sweden)

Liang Wang

2008-01-01

Full Text Available With the advancement of digital signal processing technologies, consumers are more concerned with the quality of multimedia entertainment in automobiles. In order to meet this demand, an audio enhancement system is needed to improve bass reproduction and cancel engine noise in the cabins. This paper presents an integrated active noise control system that is based on frequency-sampling filters to track and extract the bass information from the audio signal, and a multifrequency active noise equalizer to tune the low-frequency engine harmonics to enhance the bass reproduction. In the noise cancellation mode, a maximum of 3 dB bass enhancement can be achieved with significant noise suppression, while higher bass enhancement can be achieved in the bass enhance mode. The results show that the proposed system is effective for solving both the bass audio reproduction and the noise control problems in automobile cabins.

The effect on recognition memory of noise cancelling headphones in a noisy environment with native and nonnative speakers

Directory of Open Access Journals (Sweden)

Brett R C Molesworth

2014-01-01

Full Text Available Noise has the potential to impair cognitive performance. For nonnative speakers, the effect of noise on performance is more severe than their native counterparts. What remains unknown is the effectiveness of countermeasures such as noise attenuating devices in such circumstances. Therefore, the main aim of the present research was to examine the effectiveness of active noise attenuating countermeasures in the presence of simulated aircraft noise for both native and nonnative English speakers. Thirty-two participants, half native English speakers and half native German speakers completed four recognition (cued recall tasks presented in English under four different audio conditions, all in the presence of simulated aircraft noise. The results of the research indicated that in simulated aircraft noise at 65 dB(A, performance of nonnative English speakers was poorer than for native English speakers. The beneficial effects of noise cancelling headphones in improving the signal to noise ratio led to an improved performance for nonnative speakers. These results have particular importance for organizations operating in a safety-critical environment such as aviation.

A Robust Approach For Acoustic Noise Suppression In Speech Using ANFIS

Science.gov (United States)

Martinek, Radek; Kelnar, Michal; Vanus, Jan; Bilik, Petr; Zidek, Jan

2015-11-01

The authors of this article deals with the implementation of a combination of techniques of the fuzzy system and artificial intelligence in the application area of non-linear noise and interference suppression. This structure used is called an Adaptive Neuro Fuzzy Inference System (ANFIS). This system finds practical use mainly in audio telephone (mobile) communication in a noisy environment (transport, production halls, sports matches, etc). Experimental methods based on the two-input adaptive noise cancellation concept was clearly outlined. Within the experiments carried out, the authors created, based on the ANFIS structure, a comprehensive system for adaptive suppression of unwanted background interference that occurs in audio communication and degrades the audio signal. The system designed has been tested on real voice signals. This article presents the investigation and comparison amongst three distinct approaches to noise cancellation in speech; they are LMS (least mean squares) and RLS (recursive least squares) adaptive filtering and ANFIS. A careful review of literatures indicated the importance of non-linear adaptive algorithms over linear ones in noise cancellation. It was concluded that the ANFIS approach had the overall best performance as it efficiently cancelled noise even in highly noise-degraded speech. Results were drawn from the successful experimentation, subjective-based tests were used to analyse their comparative performance while objective tests were used to validate them. Implementation of algorithms was experimentally carried out in Matlab to justify the claims and determine their relative performances.

Newtonian-noise cancellation in large-scale interferometric GW detectors using seismic tiltmeters

International Nuclear Information System (INIS)

Harms, Jan; Venkateswara, Krishna

2016-01-01

The mitigation of terrestrial gravity noise, also known as Newtonian noise (NN), is one of the foremost challenges to improve low-frequency sensitivity of ground-based gravitational-wave detectors. At frequencies above 1 Hz, it is predicted that gravity noise from seismic surface Rayleigh waves is the dominant contribution to NN in surface detectors, and may still contribute significantly in future underground detectors. Noise cancellation based on a coherent estimate of NN using data from a seismometer array was proposed in the past. In this article, we propose an alternative scheme to cancel NN using a seismic tiltmeter. It is shown that even under pessimistic assumptions concerning the complexity of the seismic field, a single tiltmeter under each test mass of the detector is sufficient to achieve substantial noise cancellation. A technical tiltmeter design is presented to achieve the required sensitivity in the Newtonian-noise frequency band. (paper)

Characteristics of noise-canceling headphones to reduce the hearing hazard for MP3 users.

Science.gov (United States)

Liang, Maojin; Zhao, Fei; French, David; Zheng, Yiqing

2012-06-01

Three pairs of headphones [standard iPod ear buds and two noise-canceling headphones (NCHs)] were chosen to investigate frequency characteristics of noise reduction, together with their attenuation effects on preferred listening levels (PLLs) in the presence of various types of background noise. Twenty-six subjects with normal hearing chose their PLLs in quiet, street noise, and subway noise using the three headphones and with the noise-canceling system on/off. Both sets of NCHs reduced noise levels at mid- and high-frequencies. Further noise reductions occurred in low frequencies with the noise canceling system switched on. In street noise, both NCHs had similar noise reduction effects. In subway noise, better noise reduction effects were found in the expensive NCH and with noise-canceling on. A two way repeated measures analysis of variance showed that both listening conditions and headphone styles were significant influencing factors on the PLLs. Subjects tended to increase their PLLs as the background noise level increased. Compared with ear buds, PLLs obtained from NCHs-on in the presence of background noise were reduced up to 4 dB. Therefore, proper selection and use of NCHs appears beneficial in reducing the risk of hearing damage caused by high music listening levels in the presence of background noise.

Calibration of an audio frequency noise generator

DEFF Research Database (Denmark)

Diamond, Joseph M.

1966-01-01

a noise bandwidth Bn = π/2 × (3dB bandwidth). To apply this method to low audio frequencies, the noise bandwidth of the low Q parallel resonant circuit has been found, including the effects of both series and parallel damping. The method has been used to calibrate a General Radio 1390-B noise generator...... it is used for measurement purposes. The spectral density of a noise source may be found by measuring its rms output over a known noise bandwidth. Such a bandwidth may be provided by a passive filter using accurately known elements. For example, the parallel resonant circuit with purely parallel damping has...

Audio-visual identification of place of articulation and voicing in white and babble noise.

Science.gov (United States)

Alm, Magnus; Behne, Dawn M; Wang, Yue; Eg, Ragnhild

2009-07-01

Research shows that noise and phonetic attributes influence the degree to which auditory and visual modalities are used in audio-visual speech perception (AVSP). Research has, however, mainly focused on white noise and single phonetic attributes, thus neglecting the more common babble noise and possible interactions between phonetic attributes. This study explores whether white and babble noise differentially influence AVSP and whether these differences depend on phonetic attributes. White and babble noise of 0 and -12 dB signal-to-noise ratio were added to congruent and incongruent audio-visual stop consonant-vowel stimuli. The audio (A) and video (V) of incongruent stimuli differed either in place of articulation (POA) or voicing. Responses from 15 young adults show that, compared to white noise, babble resulted in more audio responses for POA stimuli, and fewer for voicing stimuli. Voiced syllables received more audio responses than voiceless syllables. Results can be attributed to discrepancies in the acoustic spectra of both the noise and speech target. Voiced consonants may be more auditorily salient than voiceless consonants which are more spectrally similar to white noise. Visual cues contribute to identification of voicing, but only if the POA is visually salient and auditorily susceptible to the noise type.

Study of Noise Canceling Performance of Feedforward Fuzzy-Based ANC System under Non-Causal Condition

DEFF Research Database (Denmark)

Mojallali, Hamed; Izadi-Zamanabadi, Roozbeh; Amini, Rouzbeh

of noise canceling performance of feed-forward fuzzy-based ANC systems for ducts under non-causal condition is presented. For this purpose, we use fuzzy filtered-x algorithm as an adaptive filter and the results are compared with classical filteredx algorithm which is employed under the same conditions......Feed-forward active noise control (ANC) systems act as adaptive systems to control and cancel undesired signals and noises. If the delay in the noise canceling subsystems increases more than the delays in the primary path, non-causal condition will occur in these systems. In this paper, study....... Analysis shows that ANC systems using fuzzy algorithm has better efficiency for noise cancellation in non-causal condition....

Use of active noise cancellation devices in caregivers in the intensive care unit.

Science.gov (United States)

Akhtar, S; Weigle, C G; Cheng, E Y; Toohill, R; Berens, R J

2000-04-01

Recent development of noise cancellation devices may offer relief from noise in the intensive care unit environment. This study was conducted to evaluate the effect of noise cancellation devices on subjective hearing assessment by caregivers in the intensive care units. Randomized, double-blind. Adult medical intensive care unit and pediatric intensive care unit of a teaching hospital. Caregivers of patients, including nurses, parents, respiratory therapists, and nursing assistants from a medical intensive care unit and pediatric intensive care, were enrolled in the study. Each participant was asked to wear the headphones, functional or nonfunctional noise cancellation devices, for a minimum of 30 mins. Subjective ambient noise level was assessed on a 10-point visual analog scale (VAS) before and during headphone use by each participant. Headphone comfort and the preference of the caregiver to wear the headphone were also evaluated on a 10-point VAS. Simultaneously, objective measurement of noise was done with a sound level meter using the decibel-A scale and at each of nine octave bands at each bedspace. The functional headphones significantly reduced the subjective assessment of noise by 2 (out of 10) VAS points (p noise profiles, based on decibel-A and octave band assessments. Noise cancellation devices improve subjective assessment of noise in caretakers. The benefit of these devices on hearing loss needs further evaluation in caregivers and critically ill patients.

Amplifiers Exploiting Thermal Noise Canceling: A Review

OpenAIRE

Klumperink, Eric A.M.; Bruccoleri, Federico; Stroet, Peter; Nauta, Bram

2004-01-01

Wide-band LNAs suffer from a fundamental trade-off between noise figure NF and source impedance matching, which limits NF to values typically above 3dB. Recently, a feed-forward noise canceling technique has been proposed to break this trade-off. This paper reviews the principle of the technique and its key properties. Although the technique has been applied to wideband CMOS LNAs, it can just as well be implemented exploiting transconductance elements realized with oth...

Cancelation and its simulation using Matlab according to active noise control case study of automotive noise silencer

Science.gov (United States)

Alfisyahrin; Isranuri, I.

2018-02-01

Active Noise Control is a technique to overcome noisy with noise or sound countered with sound in scientific terminology i.e signal countered with signals. This technique can be used to dampen relevant noise in accordance with the wishes of the engineering task and reducing automotive muffler noise to a minimum. Objective of this study is to develop a Active Noise Control which should cancel the noise of automotive Exhaust (Silencer) through Signal Processing Simulation methods. Noise generator of Active Noise Control is to make the opponent signal amplitude and frequency of the automotive noise. The steps are: Firstly, the noise of automotive silencer was measured to characterize the automotive noise that its amplitude and frequency which intended to be expressed. The opposed sound which having similar character with the signal source should be generated by signal function. A comparison between the data which has been completed with simulation calculations Fourier transform field data is data that has been captured on the muffler (noise silencer) Toyota Kijang Capsule assembly 2009. MATLAB is used to simulate how the signal processing noise generated by exhaust (silencer) using FFT. This opponent is inverted phase signal from the signal source 180° conducted by Instruments of Signal Noise Generators. The process of noise cancelation examined through simulation using computer software simulation. The result is obtained that attenuation of sound (noise cancellation) has a difference of 33.7%. This value is obtained from the comparison of the value of the signal source and the signal value of the opponent. So it can be concluded that the noisy signal can be attenuated by 33.7%.

Thermal Noise Canceling in LNAs: A Review

OpenAIRE

Nauta, Bram; Klumperink, Eric A.M.; Bruccoleri, Frederico

2004-01-01

Most wide-band amplifiers suffer from a fundamental trade-off between noise figure NF and source impedance matching, which limits NF to values typically above 3dB. Recently, a feed-forward noise canceling technique has been proposed to break this trade-off. This paper reviews the principle of the technique and its key properties. Although the technique has been applied to wideband CMOS LNAs, it can just as well be implemented exploiting transconductance elements realized with other types of t...

A Tunable Low Noise Active Bandpass Filter Using a Noise Canceling Technique

OpenAIRE

Soltani, N.

2016-01-01

A monolithic tunable low noise active bandpass filter is presented in this study. Biasing voltages can control the center frequency and quality factor. By keeping the gain constant, the center frequency shift is 300 MHz. The quality factor can range from 90 to 290 at the center frequency. By using a noise cancelling circuit, noise is kept lower than 2.8 dB. The proposed filter is designed using MMIC technology with a center frequency of 2.4 GHz and a power consumption of 180 mW. ED02AH techno...

A wideband Noise-Canceling CMOS LNA exploiting a transformer

NARCIS (Netherlands)

Blaakmeer, S.C.; Klumperink, Eric A.M.; Leenaerts, Domine M.W.; Nauta, Bram

2006-01-01

Abstract — A broadband LNA incorporating single-ended to differential conversion, has been successfully implemented using a noise-canceling technique and a single on-chip transformer. The LNA achieves a high voltage gain of 19dB, a wideband input match (2.5–4.0 GHz), and a Noise Figure of 4–5.4 dB,

A wideband Noise-Canceling CMOS LNA exploiting a transformer

NARCIS (Netherlands)

Blaakmeer, S.C.; Klumperink, Eric A.M.; Leenaerts, Domine M.W.; Nauta, Bram

2006-01-01

A broadband LNA incorporating single-ended to differential conversion, has been successfully implemented using a noise-canceling technique and a single on-chip transformer. The LNA achieves a high voltage gain of 19dB, a wideband input match (2.5–4.0 GHz), and a Noise Figure of 4–5.4 dB, while

Background Noise Reduction Using Adaptive Noise Cancellation Determined by the Cross-Correlation

Science.gov (United States)

Spalt, Taylor B.; Brooks, Thomas F.; Fuller, Christopher R.

2012-01-01

Background noise due to flow in wind tunnels contaminates desired data by decreasing the Signal-to-Noise Ratio. The use of Adaptive Noise Cancellation to remove background noise at measurement microphones is compromised when the reference sensor measures both background and desired noise. The technique proposed modifies the classical processing configuration based on the cross-correlation between the reference and primary microphone. Background noise attenuation is achieved using a cross-correlation sample width that encompasses only the background noise and a matched delay for the adaptive processing. A present limitation of the method is that a minimum time delay between the background noise and desired signal must exist in order for the correlated parts of the desired signal to be separated from the background noise in the crosscorrelation. A simulation yields primary signal recovery which can be predicted from the coherence of the background noise between the channels. Results are compared with two existing methods.

A Tunable Low Noise Active Bandpass Filter Using a Noise Canceling Technique

Directory of Open Access Journals (Sweden)

N. Soltani

2016-12-01

Full Text Available A monolithic tunable low noise active bandpass filter is presented in this study. Biasing voltages can control the center frequency and quality factor. By keeping the gain constant, the center frequency shift is 300 MHz. The quality factor can range from 90 to 290 at the center frequency. By using a noise cancelling circuit, noise is kept lower than 2.8 dB. The proposed filter is designed using MMIC technology with a center frequency of 2.4 GHz and a power consumption of 180 mW. ED02AH technology is used to simulate the circuit elements.

Newtonian noise cancellation in tensor gravitational wave detector

International Nuclear Information System (INIS)

Paik, Ho Jung; Harms, Jan

2016-01-01

Terrestrial gravity noise produced by ambient seismic and infrasound fields poses one of the main sensitivity limitations in low-frequency ground-based gravitational-wave (GW) detectors. This noise needs to be suppressed by 3-5 orders of magnitude in the frequency band 10 mHz to 1 Hz, which is extremely challenging. We present a new approach that greatly facilitates cancellation of gravity noise in full-tensor GW detectors. It makes explicit use of the direction of propagation of a GW, and can therefore either be implemented in directional searches for GWs or in observations of known sources. We show that suppression of the Newtonian-noise foreground is greatly facilitated using the extra strain channels in full-tensor GW detectors. Only a modest number of auxiliary, high-sensitivity environmental sensors is required to achieve noise suppression by a few orders of magnitude. (paper)

On-line adaptive line frequency noise cancellation from a nuclear power measuring channel

Directory of Open Access Journals (Sweden)

Qadir Javed

2011-01-01

Full Text Available On-line software for adaptively canceling 50 Hz line frequency noise has been designed and tested at Pakistan Research Reactor 1. Line frequency noise causes much problem in weak signals acquisition. Sometimes this noise is so dominant that original signal is totally corrupted. Although notch filter can be used for eliminating this noise, but if signal of interest is in close vicinity of 50 Hz, then original signal is also attenuated and hence overall performance is degraded. Adaptive noise removal is a technique which could be employed for removing line frequency without degrading the desired signal. In this paper line frequency noise has been eliminated on-line from a nuclear power measuring channel. The adaptive LMS algorithm has been used to cancel 50 Hz noise. The algorithm has been implemented in labVIEW with NI 6024 data acquisition card. The quality of the acquired signal has been improved much as can be seen in experimental results.

Using the effect of alcohol as a comparison to illustrate the detrimental effects of noise on performance

Directory of Open Access Journals (Sweden)

Brett R.C Molesworth

2013-01-01

Full Text Available The aim of the present research is to provide a user-friendly index of the relative impairment associated with noise in the aircraft cabin. As such, the relative effect of noise, at a level typical of an aircraft cabin was compared with varying levels of alcohol intoxication in the same subjects. Since the detrimental effect of noise is more pronounced on non-native speakers, both native English and non-native English speakers featured in the study. Noise cancelling headphones were also tested as a simple countermeasure to mitigate the effect of noise on performance. A total of 32 participants, half of which were non-native English speakers, completed a cued recall task in two alcohol conditions (blood alcohol concentration 0.05 and 0.10 and two audio conditions (audio played through the speaker and noise cancelling headphones. The results revealed that aircraft noise at 65 dB (A negatively affected performance to a level comparable to alcohol intoxication of 0.10. The results also supported previous research that reflects positively on the benefits of noise cancelling headphones in reducing the effects of noise on performance especially for non-native English speakers. These findings provide for personnel involved in the aviation industry, a user-friendly index of the relative impairment associated with noise in the aircraft cabin as compared with the effects of alcohol. They also highlight the benefits of a simple countermeasure such as noise cancelling headphones in mitigating some of the detrimental effects of noise on performance.

Investigation of LO-leakage cancellation and DC-offset influence on flicker-noise in X-band mixers

DEFF Research Database (Denmark)

Michaelsen, Rasmus; Johansen, Tom; Tamborg, Kjeld

2012-01-01

This paper describes an investigation on the influences in 1/f noise of LO-leakage and DC-offset cancellation for X-band mixers. Conditions for LO-leakage cancellation and zero DC-offset is derived. Measurements on a double balanced diode mixer shows an improvement in noise figure from 14.3dB to ...

A 115dB-DR Audio DAC with –61dBFS out-of-band noise

NARCIS (Netherlands)

Westerveld, H.J.; Schinkel, Daniel; van Tuijl, Adrianus Johannes Maria

2015-01-01

Out-of-band noise (OBN) is troublesome in analog circuits that process the output of a noise-shaping audio DAC. It causes slewing in amplifiers and aliasing in sampling circuits like ADCs and class-D amplifiers. Nonlinearity in these circuits also causes cross-modulation of the OBN into the audio

The effects of motorcycle helmets on hearing and the detection of warning signals

Science.gov (United States)

Van Moorhem, W. K.; Shepherd, K. P.; Magleby, T. D.; Torian, G. E.

1981-07-01

Measurements of the at-ear helmet-generated aerodynamic noise and helmet insertion loss were carried out for the two major types of motorcycle helmets. From these data and existing information on noise generation by flow around a bare head it was found that for quiet motorcycles at typical operating speeds a significant part of the riders at-ear noise is generated by the air flow. An assessment of the possibility of hearing damage was then carried out. It was found that only with extremely high usage would there be a significant risk of hearing damage for either the bare headed or helmeted rider. Helmets did, however, give significant protection. Detection of warning signals was then considered. It was found that under none of the conditions investigated here did the helmet put its wearer at a disadvantage compared with the bare headed rider, and at typical constant speeds the helmet gave a rider an advantage in the detection of warning signals.

Comparative study of adaptive-noise-cancellation algorithms for intrusion detection systems

International Nuclear Information System (INIS)

Claassen, J.P.; Patterson, M.M.

1981-01-01

Some intrusion detection systems are susceptible to nonstationary noise resulting in frequent nuisance alarms and poor detection when the noise is present. Adaptive inverse filtering for single channel systems and adaptive noise cancellation for two channel systems have both demonstrated good potential in removing correlated noise components prior detection. For such noise susceptible systems the suitability of a noise reduction algorithm must be established in a trade-off study weighing algorithm complexity against performance. The performance characteristics of several distinct classes of algorithms are established through comparative computer studies using real signals. The relative merits of the different algorithms are discussed in the light of the nature of intruder and noise signals

Low-noise audio amplifiers and preamplifier for use with intrinsic thermocouples

International Nuclear Information System (INIS)

Langner, G.C.; Sachs, R.D.; Stewart, F.L.

1979-03-01

Two simple, low-noise audio amplifiers and one low-noise preamplifier for use with intrinsic thermocouples were designed, built, and tested. The amplifiers and the preamplifier have different front end designs. One amplifier uses ultralow-noise operational amplifiers; the other amplifier uses a hybrid component. The preamplifier uses ultralow-noise discrete components. The amplifiers' equivalent noise inputs, at maximum gain, are 4.09 nV and 50 nV; the preamplifier's input is 4.05 μV. Their bandwidths are 15 600 Hz, 550 Hz, and 174 kHz, respectively. the amplifiers' equivalent noise inputs were measured from approx. 0 to 100 Hz, whereas the preamplifier's equivalent noise input was measured from approx. 0 to 174 kHz

Inference from the futures: ranking the noise cancelling accuracy of realized measures

DEFF Research Database (Denmark)

Mirone, Giorgio

We consider the log-linear relationship between futures contracts and their underlying assets and show that in the classical Brownian semi-martingale (BSM) framework the two series must, by no-arbitrage, have the same integrated variance. We then introduce the concept of noise cancelling...... measures in the presence of noise. Moreover, a thorough simulation analysis is employed to evaluate the estimators' sensitivity to different price and noise processes, and sampling frequencies....

Force sensing based on coherent quantum noise cancellation in a hybrid optomechanical cavity with squeezed-vacuum injection

Science.gov (United States)

Motazedifard, Ali; Bemani, F.; Naderi, M. H.; Roknizadeh, R.; Vitali, D.

2016-07-01

We propose and analyse a feasible experimental scheme for a quantum force sensor based on the elimination of backaction noise through coherent quantum noise cancellation (CQNC) in a hybrid atom-cavity optomechanical setup assisted with squeezed vacuum injection. The force detector, which allows for a continuous, broadband detection of weak forces well below the standard quantum limit (SQL), is formed by a single optical cavity simultaneously coupled to a mechanical oscillator and to an ensemble of ultracold atoms. The latter acts as a negative-mass oscillator so that atomic noise exactly cancels the backaction noise from the mechanical oscillator due to destructive quantum interference. Squeezed vacuum injection enforces this cancellation and allows sub-SQL sensitivity to be reached in a very wide frequency band, and at much lower input laser powers.

Force sensing based on coherent quantum noise cancellation in a hybrid optomechanical cavity with squeezed-vacuum injection

International Nuclear Information System (INIS)

Motazedifard, Ali; Bemani, F; Naderi, M H; Roknizadeh, R; Vitali, D

2016-01-01

We propose and analyse a feasible experimental scheme for a quantum force sensor based on the elimination of backaction noise through coherent quantum noise cancellation (CQNC) in a hybrid atom-cavity optomechanical setup assisted with squeezed vacuum injection. The force detector, which allows for a continuous, broadband detection of weak forces well below the standard quantum limit (SQL), is formed by a single optical cavity simultaneously coupled to a mechanical oscillator and to an ensemble of ultracold atoms. The latter acts as a negative-mass oscillator so that atomic noise exactly cancels the backaction noise from the mechanical oscillator due to destructive quantum interference. Squeezed vacuum injection enforces this cancellation and allows sub-SQL sensitivity to be reached in a very wide frequency band, and at much lower input laser powers. (paper)

Active control of the noise

International Nuclear Information System (INIS)

Rodriguez V, Luis Alfonso; Lopez Q, Jose German

2001-01-01

The problems of acoustic noise are more and more preponderant in the measure in that the amount of equipment and industrial machinery is increased such as fans, transformers, compressors etc. the use of devices passive mechanics for the reduction of the noise is effective and very appreciated because its effects embrace a wide range of acoustic frequency. However, to low frequencies, such devices become too big and expensive besides that present a tendency to do not effective. The control of active noise, CAN, using the electronic generation anti-noise, constitutes an interesting solution to the problem because their operation principle allows achieving an appreciable reduction of the noise by means of the use of compact devices. The traditional techniques for the control of acoustic noise like barriers and silenced to attenuate it, are classified as passive and their works has been accepted as norm as for the treatment of problems of noise it refers. Such techniques are considered in general very effective in the attenuation of noise of wide band. However, for low frequency, the required passive structures are too big and expensive; also, their effectiveness diminishes flagrantly, that which makes them impractical in many applications. The active suppression is profiled like a practical alternative for the reduction of acoustic noise. The idea in the active treatment of the noise it contemplates the use of a device electro-acoustic, like a speaker for example that it cancels to the noise by the generation of sounds of Same width and of contrary phase (anti-noise). The cancellation phenomenon is carried out when the ant-noise combines acoustically with the noise, what is in the cancellation of both sounds. The effectiveness of the cancellation of the primary source of noise depends on the precision with which the width and the phase of the generated ant-noise are controlled. The active control of noise, ANC (activates noise control), it is being investigated for

Active Control of Fan Noise: Feasibility Study. Volume 3; Active Fan Noise Cancellation in the NASA Lewis Active Noise Control Fan Facility

Science.gov (United States)

Pla, Frederic G.; Hu, Ziqiang; Sutliff, Daniel L.

1996-01-01

This report describes the Active Noise Cancellation (ANC) System designed by General Electric and tested in the NASA Lewis Research Center's (LERC) 48 inch Active Noise Control Fan (ANCF). The goal of this study is to assess the feasibility of using wall mounted secondary acoustic sources and sensors within the duct of a high bypass turbofan aircraft engine for global active noise cancellation of fan tones. The GE ANC system is based on a modal control approach. A known acoustic mode propagating in the fan duct is canceled using an array of flush-mounted compact sound sources. The canceling modal signal is generated by a modal controller. Inputs to the controller are signals from a shaft encoder and from a microphone array which senses the residual acoustic mode in the duct. The key results are that the (6,0) was completely eliminated at the 920 Hz design frequency and substantially reduced elsewhere. The total tone power was reduced 6.8 dB (out of a possible 9.8 dB). Farfield reductions of 15 dB (SPL) were obtained. The (4,0) and (4,1) modes were reduced simultaneously yielding a 15 dB PWL decrease. The results indicate that global attenuation of PWL at the target frequency was obtained in the aft quadrant using an ANC actuator and sensor system totally contained within the duct. The quality of the results depended on precise mode generation. High spillover into spurious modes generated by the ANC actuator array caused less than optimum levels of PWL reduction. The variation in spillover is believed to be due to calibration procedure, but must be confirmed in subsequent tests.

Evaluation of the Performance of Feedforward and Recurrent Neural Networks in Active Cancellation of Sound Noise

Directory of Open Access Journals (Sweden)

Mehrshad Salmasi

2012-07-01

Full Text Available Active noise control is based on the destructive interference between the primary noise and generated noise from the secondary source. An antinoise of equal amplitude and opposite phase is generated and combined with the primary noise. In this paper, performance of the neural networks is evaluated in active cancellation of sound noise. For this reason, feedforward and recurrent neural networks are designed and trained. After training, performance of the feedforwrad and recurrent networks in noise attenuation are compared. We use Elman network as a recurrent neural network. For simulations, noise signals from a SPIB database are used. In order to compare the networks appropriately, equal number of layers and neurons are considered for the networks. Moreover, training and test samples are similar. Simulation results show that feedforward and recurrent neural networks present good performance in noise cancellation. As it is seen, the ability of recurrent neural network in noise attenuation is better than feedforward network.

Design and analysis of a BLPC vocoder-based adaptive feedback cancellation with probe noise

DEFF Research Database (Denmark)

Anand, Ankita; Kar, Asutosh; Swamy, M.N.S.

2017-01-01

a BLPC vocoderbased adaptive feedback canceller with probe noise with an objective of reducing the low-frequency bias in digital hearing-aids. A step-wise mathematical analysis of the proposed feedback canceller is presented employing the recursive least square and normalized least mean square adaptive......The band-limited linear predictive coding (BLPC) vocoder-based adaptive feedback cancellation (AFC) removes the high-frequency bias, while the low frequency bias persists between the desired input signal and the loudspeaker signal in the estimate of the feedback path. In this paper, we present...... algorithms. It is observed that the optimal solution of the feedback path is unbiased for an unshaped probe noise, but is biased for a shaped probe signal; the bias term does not consist of correlation between the desired input and the loudspeaker output. The identifiability conditions are analysed...

Multireference adaptive noise canceling applied to the EEG.

Science.gov (United States)

James, C J; Hagan, M T; Jones, R D; Bones, P J; Carroll, G J

1997-08-01

The technique of multireference adaptive noise canceling (MRANC) is applied to enhance transient nonstationarities in the electroeancephalogram (EEG), with the adaptation implemented by means of a multilayer-perception artificial neural network (ANN). The method was applied to recorded EEG segments and the performance on documented nonstationarities recorded. The results show that the neural network (nonlinear) gives an improvement in performance (i.e., signal-to-noise ratio (SNR) of the nonstationarities) compared to a linear implementation of MRANC. In both cases an improvement in the SNR was obtained. The advantage of the spatial filtering aspect of MRANC is highlighted when the performance of MRANC is compared to that of the inverse auto-regressive filtering of the EEG, a purely temporal filter.

High Dynamic Range RF Front End with Noise Cancellation and Linearization for WiMAX Receivers

Directory of Open Access Journals (Sweden)

J.-M. Wu

2012-06-01

Full Text Available This research deals with verification of the high dynamic range for a heterodyne radio frequency (RF front end. A 2.6 GHz RF front end is designed and implemented in a hybrid microwave integrated circuit (HMIC for worldwide interoperability for microwave access (WiMAX receivers. The heterodyne RF front end consists of a low-noise amplifier (LNA with noise cancellation, an RF bandpass filter (BPF, a downconverter with linearization, and an intermediate frequency (IF BPF. A noise canceling technique used in the low-noise amplifier eliminates a thermal noise and then reduces the noise figure (NF of the RF front end by 0.9 dB. Use of a downconverter with diode linearizer also compensates for gain compression, which increases the input-referred third-order intercept point (IIP3 of the RF front end by 4.3 dB. The proposed method substantially increases the spurious-free dynamic range (DRf of the RF front end by 3.5 dB.

A Background Noise Reduction Technique Using Adaptive Noise Cancellation for Microphone Arrays

Science.gov (United States)

Spalt, Taylor B.; Fuller, Christopher R.; Brooks, Thomas F.; Humphreys, William M., Jr.; Brooks, Thomas F.

2011-01-01

Background noise in wind tunnel environments poses a challenge to acoustic measurements due to possible low or negative Signal to Noise Ratios (SNRs) present in the testing environment. This paper overviews the application of time domain Adaptive Noise Cancellation (ANC) to microphone array signals with an intended application of background noise reduction in wind tunnels. An experiment was conducted to simulate background noise from a wind tunnel circuit measured by an out-of-flow microphone array in the tunnel test section. A reference microphone was used to acquire a background noise signal which interfered with the desired primary noise source signal at the array. The technique s efficacy was investigated using frequency spectra from the array microphones, array beamforming of the point source region, and subsequent deconvolution using the Deconvolution Approach for the Mapping of Acoustic Sources (DAMAS) algorithm. Comparisons were made with the conventional techniques for improving SNR of spectral and Cross-Spectral Matrix subtraction. The method was seen to recover the primary signal level in SNRs as low as -29 dB and outperform the conventional methods. A second processing approach using the center array microphone as the noise reference was investigated for more general applicability of the ANC technique. It outperformed the conventional methods at the -29 dB SNR but yielded less accurate results when coherence over the array dropped. This approach could possibly improve conventional testing methodology but must be investigated further under more realistic testing conditions.

Hardware Implementation of LMS-Based Adaptive Noise Cancellation Core with Low Resource Utilization

Directory of Open Access Journals (Sweden)

Omid Sharifi Tehrani

2011-10-01

Full Text Available A hardware implementation of adaptive noise cancellation (ANC core is proposed. Adaptive filters are widely used in different applications such as adaptive noise cancellation, prediction, equalization, inverse modeling and system identification. FIR adaptive filters are mostly used because of their low computation costs and their linear phase. Least mean squared algorithm (LMS is used to train FIR adaptive filter weights. Advances in semiconductor technology especially in digital signal processors (DSP and field programmable gate arrays (FPGA with hundreds of mega hertz in speed, will allow digital designers to embed essential digital signal processing units in small chips. But designing a synthesizable core on an FPGA is not always as simple as DSP chips due to complexity and limitations of FPGAs. In this paper we design anLMS-based FIR adaptive filter for adaptive noise cancellation based on VHDL97 hardware description language (HDL and Xilinx SPARTAN3E (XC3S500E which utilizes low resources and is high performance and FPGA-brand independent so can be implemented on different FPGA brands (Xilinx, ALTERA, ACTEL. Simulations are done in MODELSIM and MATLAB and implementation is done with Xilinx ISE. Finally, result are compared with other papers for better judgment.

Noise-cancelled, cavity-enhanced saturation laser spectroscopy for laser frequency stabilisation

International Nuclear Information System (INIS)

Vine, Glenn de; McClelland, David E; Gray, Malcolm B

2006-01-01

We employ a relatively simple experimental technique enabling mechanical-noise free, cavityenhanced spectroscopic measurements of an atomic transition and its hyperfine structure. We demonstrate this technique with the 532 nm frequency doubled output from a Nd:YAG laser and an iodine vapour cell. The resulting cavity-enhanced, noise-cancelled, iodine hyperfine error signal is used as a frequency reference with which we stabilise the frequency of the 1064nm Nd:YAG laser. Preliminary frequency stabilisation results are then presented

A Hybrid Semi-Digital Transimpedance Amplifier With Noise Cancellation Technique for Nanopore-Based DNA Sequencing.

Science.gov (United States)

Hsu, Chung-Lun; Jiang, Haowei; Venkatesh, A G; Hall, Drew A

2015-10-01

Over the past two decades, nanopores have been a promising technology for next generation deoxyribonucleic acid (DNA) sequencing. Here, we present a hybrid semi-digital transimpedance amplifier (HSD-TIA) to sense the minute current signatures introduced by single-stranded DNA (ssDNA) translocating through a nanopore, while discharging the baseline current using a semi-digital feedback loop. The amplifier achieves fast settling by adaptively tuning a DC compensation current when a step input is detected. A noise cancellation technique reduces the total input-referred current noise caused by the parasitic input capacitance. Measurement results show the performance of the amplifier with 31.6 M Ω mid-band gain, 950 kHz bandwidth, and 8.5 fA/ √Hz input-referred current noise, a 2× noise reduction due to the noise cancellation technique. The settling response is demonstrated by observing the insertion of a protein nanopore in a lipid bilayer. Using the nanopore, the HSD-TIA was able to measure ssDNA translocation events.

Transient plasma estimation: a noise cancelling/identification approach

International Nuclear Information System (INIS)

Candy, J.V.; Casper, T.; Kane, R.

1985-03-01

The application of a noise cancelling technique to extract energy storage information from sensors occurring during fusion reactor experiments on the Tandem Mirror Experiment-Upgrade (TMX-U) at the Lawrence Livermore National Laboratory (LLNL) is examined. We show how this technique can be used to decrease the uncertainty in the corresponding sensor measurements used for diagnostics in both real-time and post-experimental environments. We analyze the performance of algorithm on the sensor data and discuss the various tradeoffs. The algorithm suggested is designed using SIG, an interactive signal processing package developed at LLNL

Self-Interference Cancellation Using Time-Domain Phase Noise Estimation in OFDM Full-Duplex Systems

OpenAIRE

Shehata, Heba; Khattab, Tamer

2016-01-01

In full-duplex systems, oscillator phase noise (PN) problem is considered the bottleneck challenge that may face the self-interference cancellation (SIC) stage especially when orthogonal frequency division multiplexing (OFDM) transmission scheme is deployed. Phase noise degrades the SIC performance significantly, if not mitigated before or during the SIC technique. The presence of the oscillator phase noise has different impacts on the transmitted data symbol like common phase error (CPE) and...

An OFDM Receiver with Frequency Domain Diversity Combined Impulsive Noise Canceller for Underwater Network

Science.gov (United States)

Saotome, Rie; Hai, Tran Minh; Matsuda, Yasuto; Suzuki, Taisaku; Wada, Tomohisa

2015-01-01

In order to explore marine natural resources using remote robotic sensor or to enable rapid information exchange between ROV (remotely operated vehicles), AUV (autonomous underwater vehicle), divers, and ships, ultrasonic underwater communication systems are used. However, if the communication system is applied to rich living creature marine environment such as shallow sea, it suffers from generated Impulsive Noise so-called Shrimp Noise, which is randomly generated in time domain and seriously degrades communication performance in underwater acoustic network. With the purpose of supporting high performance underwater communication, a robust digital communication method for Impulsive Noise environments is necessary. In this paper, we propose OFDM ultrasonic communication system with diversity receiver. The main feature of the receiver is a newly proposed Frequency Domain Diversity Combined Impulsive Noise Canceller. The OFDM receiver utilizes 20–28 KHz ultrasonic channel and subcarrier spacing of 46.875 Hz (MODE3) and 93.750 Hz (MODE2) OFDM modulations. In addition, the paper shows Impulsive Noise distribution data measured at a fishing port in Okinawa and at a barge in Shizuoka prefectures and then proposed diversity OFDM transceivers architecture and experimental results are described. By the proposed Impulsive Noise Canceller, frame bit error rate has been decreased by 20–30%. PMID:26351656

An OFDM Receiver with Frequency Domain Diversity Combined Impulsive Noise Canceller for Underwater Network.

Science.gov (United States)

Saotome, Rie; Hai, Tran Minh; Matsuda, Yasuto; Suzuki, Taisaku; Wada, Tomohisa

2015-01-01

In order to explore marine natural resources using remote robotic sensor or to enable rapid information exchange between ROV (remotely operated vehicles), AUV (autonomous underwater vehicle), divers, and ships, ultrasonic underwater communication systems are used. However, if the communication system is applied to rich living creature marine environment such as shallow sea, it suffers from generated Impulsive Noise so-called Shrimp Noise, which is randomly generated in time domain and seriously degrades communication performance in underwater acoustic network. With the purpose of supporting high performance underwater communication, a robust digital communication method for Impulsive Noise environments is necessary. In this paper, we propose OFDM ultrasonic communication system with diversity receiver. The main feature of the receiver is a newly proposed Frequency Domain Diversity Combined Impulsive Noise Canceller. The OFDM receiver utilizes 20-28 KHz ultrasonic channel and subcarrier spacing of 46.875 Hz (MODE3) and 93.750 Hz (MODE2) OFDM modulations. In addition, the paper shows Impulsive Noise distribution data measured at a fishing port in Okinawa and at a barge in Shizuoka prefectures and then proposed diversity OFDM transceivers architecture and experimental results are described. By the proposed Impulsive Noise Canceller, frame bit error rate has been decreased by 20-30%.

An OFDM Receiver with Frequency Domain Diversity Combined Impulsive Noise Canceller for Underwater Network

Directory of Open Access Journals (Sweden)

Rie Saotome

2015-01-01

Full Text Available In order to explore marine natural resources using remote robotic sensor or to enable rapid information exchange between ROV (remotely operated vehicles, AUV (autonomous underwater vehicle, divers, and ships, ultrasonic underwater communication systems are used. However, if the communication system is applied to rich living creature marine environment such as shallow sea, it suffers from generated Impulsive Noise so-called Shrimp Noise, which is randomly generated in time domain and seriously degrades communication performance in underwater acoustic network. With the purpose of supporting high performance underwater communication, a robust digital communication method for Impulsive Noise environments is necessary. In this paper, we propose OFDM ultrasonic communication system with diversity receiver. The main feature of the receiver is a newly proposed Frequency Domain Diversity Combined Impulsive Noise Canceller. The OFDM receiver utilizes 20–28 KHz ultrasonic channel and subcarrier spacing of 46.875 Hz (MODE3 and 93.750 Hz (MODE2 OFDM modulations. In addition, the paper shows Impulsive Noise distribution data measured at a fishing port in Okinawa and at a barge in Shizuoka prefectures and then proposed diversity OFDM transceivers architecture and experimental results are described. By the proposed Impulsive Noise Canceller, frame bit error rate has been decreased by 20–30%.

Phase noise cancellation in polarisation-maintaining fibre links

Science.gov (United States)

Rauf, B.; Vélez López, M. C.; Thoumany, P.; Pizzocaro, M.; Calonico, D.

2018-03-01

The distribution of ultra-narrow linewidth laser radiation is an integral part of many challenging metrological applications. Changes in the optical pathlength induced by environmental disturbances compromise the stability and accuracy of optical fibre networks distributing the laser light and call for active phase noise cancellation. Here we present a laboratory scale optical (at 578 nm) fibre network featuring all polarisation maintaining fibres in a setup with low optical powers available and tracking voltage-controlled oscillators implemented. The stability and accuracy of this system reach performance levels below 1 × 10-19 after 10 000 s of averaging.

Evaluation of the Performance of Feedforward and Recurrent Neural Networks in Active Cancellation of Sound Noise

OpenAIRE

Mehrshad Salmasi; Homayoun Mahdavi-Nasab

2012-01-01

Active noise control is based on the destructive interference between the primary noise and generated noise from the secondary source. An antinoise of equal amplitude and opposite phase is generated and combined with the primary noise. In this paper, performance of the neural networks is evaluated in active cancellation of sound noise. For this reason, feedforward and recurrent neural networks are designed and trained. After training, performance of the feedforwrad and recurrent networks in n...

A wideband CMOS inductorless low noise amplifier employing noise cancellation for digital TV tuner applications

International Nuclear Information System (INIS)

Zhang Jihong; Bai Xuefei; Huang Lu

2013-01-01

A wideband inductorless low noise amplifier for digital TV tuner applications is presented. The proposed LNA scheme uses a composite NMOS/PMOS cross-coupled transistor pair to provide partial cancellation of noise generated by the input transistors. The chip is implemented in SMIC 0.18 μm CMOS technology. Measurement shows that the proposed LNA achieves 12.2–15.2 dB voltage gain from 300 to 900 MHz, the noise figure is below 3.1 dB and has a minimum value of 2.3 dB, and the best input-referred 1-dB compression point (IP1dB) is − 17 dBm at 900 MHz. The core consumes 7 mA current with a supply voltage of 1.8 V and occupies an area of 0.5 × 0.35 mm 2 . (semiconductor integrated circuits)

Towards a first design of a Newtonian-noise cancellation system for Advanced LIGO

International Nuclear Information System (INIS)

Coughlin, M; Mukund, N; Mitra, S; Harms, J; Driggers, J; Adhikari, R

2016-01-01

Newtonian gravitational noise from seismic fields is predicted to be a limiting noise source at low frequency for second generation gravitational-wave detectors. Mitigation of this noise will be achieved by Wiener filtering using arrays of seismometers deployed in the vicinity of all test masses. In this work, we present optimized configurations of seismometer arrays using a variety of simplified models of the seismic field based on seismic observations at LIGO Hanford. The model that best fits the seismic measurements leads to noise reduction limited predominantly by seismometer self-noise. A first simplified design of seismic arrays for Newtonian-noise cancellation at the LIGO sites is presented, which suggests that it will be sufficient to monitor surface displacement inside the buildings. (paper)

A single-ended CMOS sensing circuit for MEMS gyroscope with noise cancellation

KAUST Repository

Elsayed, Mohannad Yomn

2010-06-01

In this work, a complete single-ended readout circuit for capacitive MEMS gyroscope using chopper stabilization technique is presented. A novel noise cancellation technique is used to get rid of the bias noise. The circuit offers superior performance over state of the art readout circuits in terms of cost, gain, and noise for the given area and power consumption. The full circuit exhibits a gain of 58dB, a power dissipation of 1.3mW and an input referred noise of 12nV/√Hz. This would significantly improve the overall sensitivity of the gyroscope. The full circuit has been fabricated in 0.6um CMOS technology and it occupies an area of 0.4mm × 1mm. © 2010 IEEE.

A single-ended CMOS sensing circuit for MEMS gyroscope with noise cancellation

KAUST Repository

Elsayed, Mohannad Yomn; Emira, Ahmed; Sedky, Sherif M.; Habib, S. E. D.

2010-01-01

In this work, a complete single-ended readout circuit for capacitive MEMS gyroscope using chopper stabilization technique is presented. A novel noise cancellation technique is used to get rid of the bias noise. The circuit offers superior performance over state of the art readout circuits in terms of cost, gain, and noise for the given area and power consumption. The full circuit exhibits a gain of 58dB, a power dissipation of 1.3mW and an input referred noise of 12nV/√Hz. This would significantly improve the overall sensitivity of the gyroscope. The full circuit has been fabricated in 0.6um CMOS technology and it occupies an area of 0.4mm × 1mm. © 2010 IEEE.

Joint Use of Adaptive Equalization and Cyclic Noise Cancellation for Band-Limited OQAM Based Multi-Carrier Transmission in Power-Line Communication Systems

Science.gov (United States)

Kunishima, Hiromitsu; Koga, Hisao; Muta, Osamu; Akaiwa, Yoshihiko

Power-line communication (PLC) technique is one method to realize high-speed communications in a home network. In PLC channels, the transmission signal quality is degraded by colored non-Gaussian noise as well as frequency-selectivity of the channels. In this paper, we describe our investigation of the performance of a OQAM-MCT system in which a noise canceller is used jointly with a time-domain per-subcarrier adaptive equalizer. Furthermore, we propose a noise cancellation method designed for the OQAM-MCT system. The performance of the OQAM-MCT system is evaluated in PLC channels with measured impulse responses in the presence of measured noise. Computer simulation results show that the bit rate of the OQAM-MCT system is improved using both an adaptive equalizer and noise canceller, and that the OQAM-MCT system achieves better performance than an OFDM system with an insufficient length of the guard interval.

Extraction of Overt Verbal Response from the Acoustic Noise in a Functional Magnetic Resonance Imaging Scan by Use of Segmented Active Noise Cancellation

Science.gov (United States)

Jung, Kwan-Jin; Prasad, Parikshit; Qin, Yulin; Anderson, John R.

2013-01-01

A method to extract the subject's overt verbal response from the obscuring acoustic noise in an fMRI scan is developed by applying active noise cancellation with a conventional MRI microphone. Since the EPI scanning and its accompanying acoustic noise in fMRI are repetitive, the acoustic noise in one time segment was used as a reference noise in suppressing the acoustic noise in subsequent segments. However, the acoustic noise from the scanner was affected by the subject's movements, so the reference noise was adaptively adjusted as the scanner's acoustic properties varied in time. This method was successfully applied to a cognitive fMRI experiment with overt verbal responses. PMID:15723385

A flicker noise/IM3 cancellation technique for active mixer using negative impedance

NARCIS (Netherlands)

Cheng, W.; Annema, Anne J.; Wienk, Gerhardus J.M.; Nauta, Bram

2013-01-01

Abstract—This paper presents an approach to simultaneously cancel flicker noise and IM3 in Gilbert-type mixers, utilizing negative impedances. For proof of concept, two prototype double-balanced mixers in 0.16- m CMOS are fabricated. The first demonstration mixer chip was optimized for full IM3

MEMS microphone innovations towards high signal to noise ratios (Conference Presentation) (Plenary Presentation)

Science.gov (United States)

Dehé, Alfons

2017-06-01

After decades of research and more than ten years of successful production in very high volumes Silicon MEMS microphones are mature and unbeatable in form factor and robustness. Audio applications such as video, noise cancellation and speech recognition are key differentiators in smart phones. Microphones with low self-noise enable those functions. Backplate-free microphones enter the signal to noise ratios above 70dB(A). This talk will describe state of the art MEMS technology of Infineon Technologies. An outlook on future technologies such as the comb sensor microphone will be given.

A wide bandwidth fractional-N synthesizer for LTE with phase noise cancellation using a hybrid-ΔΣ-DAC and charge re-timing

NARCIS (Netherlands)

Ye, D.; Lu, Ping; Andreani, Pietro; van der Zee, Ronan A.R.

2013-01-01

This paper presents a 1MHz bandwidth, ΔΣ fractional-N PLL as the frequency synthesizer for LTE. A noise cancellation path composed of a novel hybrid ΔΣ DAC with 9 output bits is incorporated into the PLL in order to cancel the out-of-band phase noise caused by the quantization error. Further, a

Passive Attenuating Communication Earphone (PACE): Noise Attenuation and Speech Intelligibility Performance When Worn in Conjunction with the HGU-56/P and HGU-55/P Flight Helmets

Science.gov (United States)

2013-10-16

right) eartips The purpose of this study was to integrate the HGU-56/P and HGU-55/P flight helmets with PACE to measure the noise attenuation and...55/P flight helmet integrated with PACE 2.0 METHODS 2.1 Subjects Twenty paid volunteer subjects (9 male, 11 female) participated in the study ...Pan Pad Pat Path Pack Pass Buff Bus But Bug Buck Bun Sat Sag Sass Sack Sad Sap Run Sun Bun Gun Fun Nun 8 Distribution A: Approved for

System and method for bearing fault detection using stator current noise cancellation

Science.gov (United States)

Zhou, Wei; Lu, Bin; Habetler, Thomas G.; Harley, Ronald G.; Theisen, Peter J.

2010-08-17

A system and method for detecting incipient mechanical motor faults by way of current noise cancellation is disclosed. The system includes a controller configured to detect indicia of incipient mechanical motor faults. The controller further includes a processor programmed to receive a baseline set of current data from an operating motor and define a noise component in the baseline set of current data. The processor is also programmed to repeatedly receive real-time operating current data from the operating motor and remove the noise component from the operating current data in real-time to isolate any fault components present in the operating current data. The processor is then programmed to generate a fault index for the operating current data based on any isolated fault components.

Inadequate Helmet Fit Increases Concussion Severity in American High School Football Players

Science.gov (United States)

Greenhill, Dustin A.; Navo, Paul; Zhao, Huaqing; Torg, Joseph; Comstock, R. Dawn; Boden, Barry P.

2016-01-01

Background: There is limited information on the relationship between football helmet fit and concussion severity. Hypothesis: Poor helmet fit may predispose football players to a more severe concussion. Study Design: Descriptive epidemiology study. Level of Evidence: Level 3. Methods: Data from concussion injury reports were obtained from the National High School Sports-Related Injury Surveillance System over a 9-year period. Symptoms, duration, and helmet parameters (fit, interior padding) were analyzed for all first-time concussions. Results: Data from 4580 concussions were analyzed. Patients who suffered concussions with a helmet that did not fit properly (3.22%), as determined by an athletic trainer, had higher rates of drowsiness (RR, 1.46; P = 0.005), hyperexcitability (RR, 2.38; P = 0.047), and sensitivity to noise (RR, 1.88; P < 0.001); had more symptoms (5.34 vs 4.54, P = 0.004); and had longer symptom duration (P = 0.04). Athletes with helmets lined with an air bladder had greater rates of sensitivity to light (RR, 1.13; P = 0.02), sensitivity to noise (RR, 1.25; P = 0.009), and longer symptom duration (P = 0.004) compared with foam or gel liners. Conclusion: An improperly fitted football helmet is a risk factor for a concussion with more symptoms and of longer duration. Concussions of longer duration are also more common in players with an air bladder–lined helmet. Current high school football rules should mandate supervision and maintenance of helmet fit throughout the season, prior to impact. Clinical Relevance: Team physicians, athletic trainers, coaches, and high school officials should ensure proper oversight of helmet fit in high school athletes to decrease concussion severity and duration. PMID:27005467

Benign paroxysmal positional vertigo after use of noise-canceling headphones.

Science.gov (United States)

Dan-Goor, Eric; Samra, Monica

2012-01-01

Benign paroxysmal positional vertigo (BPPV) is a common cause of vertigo. We describe a case of a woman presenting acutely with a severe episode of disabling positional vertigo. Although she had no known etiologic risk factors, this attack followed 12 hours of continuously wearing digital noise-canceling headphones. This is the first such reported association between BPPV and the use of this gadget. We also provide a short review of BPPV and speculate on the possible pathogenic mechanisms involved. Copyright © 2012 Elsevier Inc. All rights reserved.

Transform Domain Robust Variable Step Size Griffiths' Adaptive Algorithm for Noise Cancellation in ECG

Science.gov (United States)

Hegde, Veena; Deekshit, Ravishankar; Satyanarayana, P. S.

2011-12-01

The electrocardiogram (ECG) is widely used for diagnosis of heart diseases. Good quality of ECG is utilized by physicians for interpretation and identification of physiological and pathological phenomena. However, in real situations, ECG recordings are often corrupted by artifacts or noise. Noise severely limits the utility of the recorded ECG and thus needs to be removed, for better clinical evaluation. In the present paper a new noise cancellation technique is proposed for removal of random noise like muscle artifact from ECG signal. A transform domain robust variable step size Griffiths' LMS algorithm (TVGLMS) is proposed for noise cancellation. For the TVGLMS, the robust variable step size has been achieved by using the Griffiths' gradient which uses cross-correlation between the desired signal contaminated with observation or random noise and the input. The algorithm is discrete cosine transform (DCT) based and uses symmetric property of the signal to represent the signal in frequency domain with lesser number of frequency coefficients when compared to that of discrete Fourier transform (DFT). The algorithm is implemented for adaptive line enhancer (ALE) filter which extracts the ECG signal in a noisy environment using LMS filter adaptation. The proposed algorithm is found to have better convergence error/misadjustment when compared to that of ordinary transform domain LMS (TLMS) algorithm, both in the presence of white/colored observation noise. The reduction in convergence error achieved by the new algorithm with desired signal decomposition is found to be lower than that obtained without decomposition. The experimental results indicate that the proposed method is better than traditional adaptive filter using LMS algorithm in the aspects of retaining geometrical characteristics of ECG signal.

System and method for motor fault detection using stator current noise cancellation

Science.gov (United States)

Zhou, Wei; Lu, Bin; Nowak, Michael P.; Dimino, Steven A.

2010-12-07

A system and method for detecting incipient mechanical motor faults by way of current noise cancellation is disclosed. The system includes a controller configured to detect indicia of incipient mechanical motor faults. The controller further includes a processor programmed to receive a baseline set of current data from an operating motor and define a noise component in the baseline set of current data. The processor is also programmed to acquire at least on additional set of real-time operating current data from the motor during operation, redefine the noise component present in each additional set of real-time operating current data, and remove the noise component from the operating current data in real-time to isolate any fault components present in the operating current data. The processor is then programmed to generate a fault index for the operating current data based on any isolated fault components.

High performance magnetic bearings suitable for noise cancellation in permanent magnet motor driven pumps

International Nuclear Information System (INIS)

Zmood, R.; Cholewka, J.; Patak, C.; Feng, G.; Zhang, C.; Maleri, T.; Pinder, B.; McDonald, R.; Homrigh, J.

1991-01-01

Conventional pumps having external drive motors experience problems due to bearing noise. In addition failure of bearings and seals can lead to limited operational reliability and impaired integrity of these pumps. Pumps using DC brushless motors and magnetic bearings offer means of overcoming these problems. A design of a pump having a DC brushless motor and magnetic bearings with a potential for Naval applications in ships and submarines is discussed. In this paper attention is given to the selection of the magnetic bearings suitable for achieving active noise cancellation

Gravitational wave searches with pulsar timing arrays: Cancellation of clock and ephemeris noises

Science.gov (United States)

Tinto, Massimo

2018-04-01

We propose a data processing technique to cancel monopole and dipole noise sources (such as clock and ephemeris noises, respectively) in pulsar timing array searches for gravitational radiation. These noises are the dominant sources of correlated timing fluctuations in the lower-part (≈10-9-10-8 Hz ) of the gravitational wave band accessible by pulsar timing experiments. After deriving the expressions that reconstruct these noises from the timing data, we estimate the gravitational wave sensitivity of our proposed processing technique to single-source signals to be at least one order of magnitude higher than that achievable by directly processing the timing data from an equal-size array. Since arrays can generate pairs of clock and ephemeris-free timing combinations that are no longer affected by correlated noises, we implement with them the cross-correlation statistic to search for an isotropic stochastic gravitational wave background. We find the resulting optimal signal-to-noise ratio to be more than one order of magnitude larger than that obtainable by correlating pairs of timing data from arrays of equal size.

A 0.18 μm biosensor front-end based on 1/f noise, distortion cancelation and chopper stabilization techniques.

Science.gov (United States)

Balasubramanian, Viswanathan; Ruedi, Pierre-Francois; Temiz, Yuksel; Ferretti, Anna; Guiducci, Carlotta; Enz

2013-10-01

This paper presents a novel sensor front-end circuit that addresses the issues of 1/f noise and distortion in a unique way by using canceling techniques. The proposed front-end is a fully differential transimpedance amplifier (TIA) targeted for current mode electrochemical biosensing applications. In this paper, we discuss the architecture of this canceling based front-end and the optimization methods followed for achieving low noise, low distortion performance at minimum current consumption are presented. To validate the employed canceling based front-end, it has been realized in a 0.18 μm CMOS process and the characterization results are presented. The front-end has also been tested as part of a complete wireless sensing system and the cyclic voltammetry (CV) test results from electrochemical sensors are provided. Overall current consumption in the front-end is 50 μA while operating on a 1.8 V supply.

FPGA implementation of ICA algorithm for blind signal separation and adaptive noise canceling.

Science.gov (United States)

Kim, Chang-Min; Park, Hyung-Min; Kim, Taesu; Choi, Yoon-Kyung; Lee, Soo-Young

2003-01-01

An field programmable gate array (FPGA) implementation of independent component analysis (ICA) algorithm is reported for blind signal separation (BSS) and adaptive noise canceling (ANC) in real time. In order to provide enormous computing power for ICA-based algorithms with multipath reverberation, a special digital processor is designed and implemented in FPGA. The chip design fully utilizes modular concept and several chips may be put together for complex applications with a large number of noise sources. Experimental results with a fabricated test board are reported for ANC only, BSS only, and simultaneous ANC/BSS, which demonstrates successful speech enhancement in real environments in real time.

Microphone Handling Noise: Measurements of Perceptual Threshold and Effects on Audio Quality.

Directory of Open Access Journals (Sweden)

Paul Kendrick

Full Text Available A psychoacoustic experiment was carried out to test the effects of microphone handling noise on perceived audio quality. Handling noise is a problem affecting both amateurs using their smartphones and cameras, as well as professionals using separate microphones and digital recorders. The noises used for the tests were measured from a variety of devices, including smartphones, laptops and handheld microphones. The signal features that characterise these noises are analysed and presented. The sounds include various types of transient, impact noises created by tapping or knocking devices, as well as more sustained sounds caused by rubbing. During the perceptual tests, listeners auditioned speech podcasts and were asked to rate the degradation of any unwanted sounds they heard. A representative design test methodology was developed that tried to encourage everyday rather than analytical listening. Signal-to-noise ratio (SNR of the handling noise events was shown to be the best predictor of quality degradation. Other factors such as noise type or background noise in the listening environment did not significantly affect quality ratings. Podcast, microphone type and reproduction equipment were found to be significant but only to a small extent. A model allowing the prediction of degradation from the SNR is presented. The SNR threshold at which 50% of subjects noticed handling noise was found to be 4.2 ± 0.6 dBA. The results from this work are important for the understanding of our perception of impact sound and resonant noises in recordings, and will inform the future development of an automated predictor of quality for handling noise.

Robust audio-visual speech recognition under noisy audio-video conditions.

Science.gov (United States)

Stewart, Darryl; Seymour, Rowan; Pass, Adrian; Ming, Ji

2014-02-01

This paper presents the maximum weighted stream posterior (MWSP) model as a robust and efficient stream integration method for audio-visual speech recognition in environments, where the audio or video streams may be subjected to unknown and time-varying corruption. A significant advantage of MWSP is that it does not require any specific measurements of the signal in either stream to calculate appropriate stream weights during recognition, and as such it is modality-independent. This also means that MWSP complements and can be used alongside many of the other approaches that have been proposed in the literature for this problem. For evaluation we used the large XM2VTS database for speaker-independent audio-visual speech recognition. The extensive tests include both clean and corrupted utterances with corruption added in either/both the video and audio streams using a variety of types (e.g., MPEG-4 video compression) and levels of noise. The experiments show that this approach gives excellent performance in comparison to another well-known dynamic stream weighting approach and also compared to any fixed-weighted integration approach in both clean conditions or when noise is added to either stream. Furthermore, our experiments show that the MWSP approach dynamically selects suitable integration weights on a frame-by-frame basis according to the level of noise in the streams and also according to the naturally fluctuating relative reliability of the modalities even in clean conditions. The MWSP approach is shown to maintain robust recognition performance in all tested conditions, while requiring no prior knowledge about the type or level of noise.

Audio-frequency noise emissions from high-voltage overhead power lines

International Nuclear Information System (INIS)

Semmler, M.; Straumann, U.; Roero, C.; Teich, T. H.

2005-01-01

This article discusses the noise-emissions caused by high-voltage overhead power lines that can occur under certain atmospheric conditions. These emissions, caused by electric discharges around the conductors, can achieve disturbing values, depending on the conditions prevailing at the time in question. The causes of the discharges are examined and the ionisation processes involved are looked at. The parameters influencing the discharges are discussed and measures that can be taken to reduce such audio-frequency emissions are looked at. The authors note that a reduction of peripheral field strengths can reduce emissions and that hydrophilic coatings can lead to faster reduction of such effects after rainfall

Inadequate Helmet Fit Increases Concussion Severity in American High School Football Players.

Science.gov (United States)

Greenhill, Dustin A; Navo, Paul; Zhao, Huaqing; Torg, Joseph; Comstock, R Dawn; Boden, Barry P

2016-05-01

There is limited information on the relationship between football helmet fit and concussion severity. Poor helmet fit may predispose football players to a more severe concussion. Descriptive epidemiology study. Level 3. Data from concussion injury reports were obtained from the National High School Sports-Related Injury Surveillance System over a 9-year period. Symptoms, duration, and helmet parameters (fit, interior padding) were analyzed for all first-time concussions. Data from 4580 concussions were analyzed. Patients who suffered concussions with a helmet that did not fit properly (3.22%), as determined by an athletic trainer, had higher rates of drowsiness (RR, 1.46; P = 0.005), hyperexcitability (RR, 2.38; P = 0.047), and sensitivity to noise (RR, 1.88; P football helmet is a risk factor for a concussion with more symptoms and of longer duration. Concussions of longer duration are also more common in players with an air bladder-lined helmet. Current high school football rules should mandate supervision and maintenance of helmet fit throughout the season, prior to impact. Team physicians, athletic trainers, coaches, and high school officials should ensure proper oversight of helmet fit in high school athletes to decrease concussion severity and duration. © 2016 The Author(s).

The effect of losses on the quantum-noise cancellation in the SU(1,1) interferometer

International Nuclear Information System (INIS)

Xin, Jun; Wang, Hailong; Jing, Jietai

2016-01-01

Quantum-noise cancellation (QNC) is an effective method to control the noise of the quantum system, which reduces or even eliminates the noise of the quantum systems by utilizing destructive interference in the quantum system. However, QNC can be extremely dependent on the losses inside the system. In this letter, we experimentally and theoretically study how the losses can affect the QNC in the SU(1,1) interferometer. We find that losses in the different arms inside the SU(1,1) interferometer can have different effects on the QNC in the output fields from the SU(1,1) interferometer. And the QNC in the SU(1,1) interferometer can almost be insensitive to the losses in some cases. Our findings may find its potential applications in the quantum noise control.

The effect of losses on the quantum-noise cancellation in the SU(1,1) interferometer

Energy Technology Data Exchange (ETDEWEB)

Xin, Jun; Wang, Hailong [State Key Laboratory of Precision Spectroscopy, School of Physics and Materials Science, East China Normal University, Shanghai 200062 (China); Jing, Jietai, E-mail: jtjing@phy.ecnu.edu.cn [State Key Laboratory of Precision Spectroscopy, School of Physics and Materials Science, East China Normal University, Shanghai 200062 (China); Collaborative Innovation Center of Extreme Optics, Shanxi University, Taiyuan, Shanxi 030006 (China)

2016-08-01

Quantum-noise cancellation (QNC) is an effective method to control the noise of the quantum system, which reduces or even eliminates the noise of the quantum systems by utilizing destructive interference in the quantum system. However, QNC can be extremely dependent on the losses inside the system. In this letter, we experimentally and theoretically study how the losses can affect the QNC in the SU(1,1) interferometer. We find that losses in the different arms inside the SU(1,1) interferometer can have different effects on the QNC in the output fields from the SU(1,1) interferometer. And the QNC in the SU(1,1) interferometer can almost be insensitive to the losses in some cases. Our findings may find its potential applications in the quantum noise control.

Fully integrated low-noise readout circuit with automatic offset cancellation loop for capacitive microsensors.

Science.gov (United States)

Song, Haryong; Park, Yunjong; Kim, Hyungseup; Cho, Dong-Il Dan; Ko, Hyoungho

2015-10-14

Capacitive sensing schemes are widely used for various microsensors; however, such microsensors suffer from severe parasitic capacitance problems. This paper presents a fully integrated low-noise readout circuit with automatic offset cancellation loop (AOCL) for capacitive microsensors. The output offsets of the capacitive sensing chain due to the parasitic capacitances and process variations are automatically removed using AOCL. The AOCL generates electrically equivalent offset capacitance and enables charge-domain fine calibration using a 10-bit R-2R digital-to-analog converter, charge-transfer switches, and a charge-storing capacitor. The AOCL cancels the unwanted offset by binary-search algorithm based on 10-bit successive approximation register (SAR) logic. The chip is implemented using 0.18 μm complementary metal-oxide-semiconductor (CMOS) process with an active area of 1.76 mm². The power consumption is 220 μW with 3.3 V supply. The input parasitic capacitances within the range of -250 fF to 250 fF can be cancelled out automatically, and the required calibration time is lower than 10 ms.

Fully Integrated Low-Noise Readout Circuit with Automatic Offset Cancellation Loop for Capacitive Microsensors

Directory of Open Access Journals (Sweden)

Haryong Song

2015-10-01

Full Text Available Capacitive sensing schemes are widely used for various microsensors; however, such microsensors suffer from severe parasitic capacitance problems. This paper presents a fully integrated low-noise readout circuit with automatic offset cancellation loop (AOCL for capacitive microsensors. The output offsets of the capacitive sensing chain due to the parasitic capacitances and process variations are automatically removed using AOCL. The AOCL generates electrically equivalent offset capacitance and enables charge-domain fine calibration using a 10-bit R-2R digital-to-analog converter, charge-transfer switches, and a charge-storing capacitor. The AOCL cancels the unwanted offset by binary-search algorithm based on 10-bit successive approximation register (SAR logic. The chip is implemented using 0.18 μm complementary metal-oxide-semiconductor (CMOS process with an active area of 1.76 mm2. The power consumption is 220 μW with 3.3 V supply. The input parasitic capacitances within the range of −250 fF to 250 fF can be cancelled out automatically, and the required calibration time is lower than 10 ms.

A 380pW Dual Mode Optical Wake-up Receiver with Ambient Noise Cancellation.

Science.gov (United States)

Lim, Wootaek; Jang, Taekwang; Lee, Inhee; Kim, Hun-Seok; Sylvester, Dennis; Blaauw, David

2016-06-01

We present a sub-nW optical wake-up receiver for wireless sensor nodes. The wake-up receiver supports dual mode operation for both ultra-low standby power and high data rates, while canceling ambient in-band noise. In 0.18µm CMOS the receiver consumes 380pW in always-on wake-up mode and 28.1µW in fast RX mode at 250kbps.

Extracting meaning from audio signals - a machine learning approach

DEFF Research Database (Denmark)

Larsen, Jan

2007-01-01

* Machine learning framework for sound search * Genre classification * Music and audio separation * Wind noise suppression......* Machine learning framework for sound search * Genre classification * Music and audio separation * Wind noise suppression...

Adaptive cancellation of motion artifact in wearable biosensors.

Science.gov (United States)

Yousefi, Rasoul; Nourani, Mehrdad; Panahi, Issa

2012-01-01

The performance of wearable biosensors is highly influenced by motion artifact. In this paper, a model is proposed for analysis of motion artifact in wearable photoplethysmography (PPG) sensors. Using this model, we proposed a robust real-time technique to estimate fundamental frequency and generate a noise reference signal. A Least Mean Square (LMS) adaptive noise canceler is then designed and validated using our synthetic noise generator. The analysis and results on proposed technique for noise cancellation shows promising performance.

A compressed sensing based method with support refinement for impulse noise cancelation in DSL

KAUST Repository

Quadeer, Ahmed Abdul

2013-06-01

This paper presents a compressed sensing based method to suppress impulse noise in digital subscriber line (DSL). The proposed algorithm exploits the sparse nature of the impulse noise and utilizes the carriers, already available in all practical DSL systems, for its estimation and cancelation. Specifically, compressed sensing is used for a coarse estimate of the impulse position, an a priori information based maximum aposteriori probability (MAP) metric for its refinement, followed by least squares (LS) or minimum mean square error (MMSE) estimation for estimating the impulse amplitudes. Simulation results show that the proposed scheme achieves higher rate as compared to other known sparse estimation algorithms in literature. The paper also demonstrates the superior performance of the proposed scheme compared to the ITU-T G992.3 standard that utilizes RS-coding for impulse noise refinement in DSL signals. © 2013 IEEE.

A Joint Audio-Visual Approach to Audio Localization

DEFF Research Database (Denmark)

Jensen, Jesper Rindom; Christensen, Mads Græsbøll

2015-01-01

Localization of audio sources is an important research problem, e.g., to facilitate noise reduction. In the recent years, the problem has been tackled using distributed microphone arrays (DMA). A common approach is to apply direction-of-arrival (DOA) estimation on each array (denoted as nodes), a...... time-of-flight cameras. Moreover, we propose an optimal method for weighting such DOA and range information for audio localization. Our experiments on both synthetic and real data show that there is a clear, potential advantage of using the joint audiovisual localization framework....

Car audio using DSP for active sound control. DSP ni yoru active seigyo wo mochiita audio

Energy Technology Data Exchange (ETDEWEB)

Yamada, K.; Asano, S.; Furukawa, N. (Mitsubishi Motor Corp., Tokyo (Japan))

1993-06-01

In the automobile cabin, there are some unique problems which spoil the quality of sound reproduction from audio equipment, such as the narrow space and/or the background noise. The audio signal processing by using DSP (digital signal processor) makes enable a solution to these problems. A car audio with a high amenity has been successfully made by the active sound control using DSP. The DSP consists of an adder, coefficient multiplier, delay unit, and connections. For the actual processing by DSP, are used functions, such as sound field correction, response and processing of noises during driving, surround reproduction, graphic equalizer processing, etc. High effectiveness of the method was confirmed through the actual driving evaluation test. The present paper describes the actual method of sound control technology using DSP. Especially, the dynamic processing of the noise during driving is discussed in detail. 1 ref., 12 figs., 1 tab.

Debugging of Class-D Audio Power Amplifiers

DEFF Research Database (Denmark)

Crone, Lasse; Pedersen, Jeppe Arnsdorf; Mønster, Jakob Døllner

2012-01-01

Determining and optimizing the performance of a Class-D audio power amplier can be very dicult without knowledge of the use of audio performance measuring equipment and of how the various noise and distortion sources in uence the audio performance. This paper gives an introduction on how to measure...

dc SQUID electronics based on adaptive noise cancellation and a high open-loop gain controller

International Nuclear Information System (INIS)

Seppae, H.

1992-01-01

A low-noise SQUID readout electronics with a high slew rate and an automatic gain control feature has been developed. Flux noise levels of 5x10 -7 Φ 0 /√Hz at 1 kHz and 2x10 -6 Φ 0 /√Hz at 1 Hz have been measured with this readout scheme. The system tolerates sinusoidal disturbances having amplitudes up to 140 Φ 0 at 1 kHz without loosing lock. The electronics utilizes a cooled GaAs FET to control the cancellation of the voltage noise of the room temperature amplifier, a PI 3/2 controller to provide a high open-loop gain at low frequencies, and a square-wave flux and offset voltage modulation to enable automatic control of the noise reduction. The cutoff frequency of the flux-locked-loop is 300 kHz and the feedback gain is more than 130 dB at 10 Hz. (orig.)

Beat Noise Cancellation in 2-D Optical Code-Division Multiple-Access Systems Using Optical Hard-Limiter Array

Science.gov (United States)

Dang, Ngoc T.; Pham, Anh T.; Cheng, Zixue

We analyze the beat noise cancellation in two-dimensional optical code-division multiple-access (2-D OCDMA) systems using an optical hard-limiter (OHL) array. The Gaussian shape of optical pulse is assumed and the impact of pulse propagation is considered. We also take into account the receiver noise and multiple access interference (MAI) in the analysis. The numerical results show that, when OHL array is employed, the system performance is greatly improved compared with the cases without OHL array. Also, parameters needed for practical system design are comprehensively analyzed.

Simulation study comparing the helmet-chin PET with a cylindrical PET of the same number of detectors

Science.gov (United States)

Ahmed, Abdella M.; Tashima, Hideaki; Yoshida, Eiji; Nishikido, Fumihiko; Yamaya, Taiga

2017-06-01

There is a growing interest in developing brain PET scanners with high sensitivity and high spatial resolution for early diagnosis of neurodegenerative diseases and studies of brain functions. Sensitivity of the PET scanner can be improved by increasing the solid angle. However, conventional PET scanners are designed based on a cylindrical geometry, which may not be the most efficient design for brain imaging in terms of the balance between sensitivity and cost. We proposed a dedicated brain PET scanner based on a hemispheric shape detector and a chin detector (referred to as the helmet-chin PET), which is designed to maximize the solid angle by increasing the number of lines-of-response in the hemisphere. The parallax error, which PET scanners with a large solid angle tend to have, can be suppressed by the use of depth-of-interaction detectors. In this study, we carry out a realistic evaluation of the helmet-chin PET using Monte Carlo simulation based on the 4-layer GSO detector which consists of a 16  ×  16  ×  4 array of crystals with dimensions of 2.8  ×  2.8  ×  7.5 mm3. The purpose of this simulation is to show the gain in imaging performance of the helmet-chin PET compared with the cylindrical PET using the same number of detectors in each configuration. The sensitivity of the helmet-chin PET evaluated with a cylindrical phantom has a significant increase, especially at the top of the (field-of-view) FOV. The peak-NECR of the helmet-chin PET is 1.4 times higher compared to the cylindrical PET. The helmet-chin PET provides relatively low noise images throughout the FOV compared to the cylindrical PET which exhibits enhanced noise at the peripheral regions. The results show the helmet-chin PET can significantly improve the sensitivity and reduce the noise in the reconstructed images.

Interpixel crosstalk cancellation on holographic memory

Science.gov (United States)

Ishii, Toshiki; Fujimura, Ryushi

2017-09-01

In holographic memory systems, there have been no practical techniques to minimize interpixel crosstalk thus far. We developed an interpixel crosstalk cancellation technique using a checkerboard phase pattern with a phase difference of π/2, which can decrease the size of the spatial filter along the Fourier plane with the signal-to-noise ratio (SNR) kept high. This interpixel crosstalk cancellation technique is simple because it requires only one phase plate in the signal beam path. We verified the effect of such a cancellation technique by simulation. The improvement of SNR is maximized to 6.5 dB when the filter size specified in the Nyquist areal ratio is approximately 1.05 in ideal optical systems with no other fixed noise. The proposed technique can improve SNR by 0.85 in an assumed monocular architecture at an actual noise intensity. This improvement of SNR is very useful for realizing high-density recording or enhancing system robustness.

A wideband LNA employing gate-inductive-peaking and noise-canceling techniques in 0.18 μm CMOS

International Nuclear Information System (INIS)

Bao Kuan; Fan Xiangning; Li Wei; Zhang Li; Wang Zhigong

2012-01-01

This paper presents a wideband low noise amplifier (LNA) for multi-standard radio applications. The low noise characteristic is achieved by the noise-canceling technique while the bandwidth is enhanced by gate-inductive-peaking technique. High-frequency noise performance is consequently improved by the flattened gain over the entire operating frequency band. Fabricated in 0.18 μm CMOS process, the LNA achieves 2.5 GHz of −3 dB bandwidth and 16 dB of gain. The gain variation is within ±0.8 dB from 300 MHz to 2.2 GHz. The measured noise figure (NF) and average IIP3 are 3.4 dB and −2 dBm, respectively. The proposed LNA occupies 0.39 mm 2 core chip area. Operating at 1.8 V, the LNA drains a current of 11.7 mA. (semiconductor integrated circuits)

A 0.18 μm CMOS inductorless complementary-noise-canceling-LNA for TV tuner applications

International Nuclear Information System (INIS)

Yuan Haiquan; Lin Fujiang; Fu Zhongqian; Huang Lu

2010-01-01

This paper presents an inductorless complementary-noise-canceling LNA (CNCLNA) for TV tuners. The CNCLNA exploits single-to-differential topology, which consists of a common gate stage and a common source stage. The complementary topology can save power and improve the noise figure. Linearity is also enhanced by employing a multiple gated transistors technique. The chip is implemented in SMIC 0.18 μm CMOS technology. Measurement shows that the proposed CNCLNA achieves 13.5-16 dB voltage gain from 50 to 860 MHz, the noise figure is below 4.5 dB and has a minimum value of 2.9 dB, and the best P 1dB is -7.5 dBm at 860 MHz. The core consumes 6 mA current with a supply voltage of 1.8 V, while the core area is only 0.2 x 0.2 mm 2 . (semiconductor integrated circuits)

Audio-Visual Speech Recognition Using MPEG-4 Compliant Visual Features

Directory of Open Access Journals (Sweden)

Petar S. Aleksic

2002-11-01

Full Text Available We describe an audio-visual automatic continuous speech recognition system, which significantly improves speech recognition performance over a wide range of acoustic noise levels, as well as under clean audio conditions. The system utilizes facial animation parameters (FAPs supported by the MPEG-4 standard for the visual representation of speech. We also describe a robust and automatic algorithm we have developed to extract FAPs from visual data, which does not require hand labeling or extensive training procedures. The principal component analysis (PCA was performed on the FAPs in order to decrease the dimensionality of the visual feature vectors, and the derived projection weights were used as visual features in the audio-visual automatic speech recognition (ASR experiments. Both single-stream and multistream hidden Markov models (HMMs were used to model the ASR system, integrate audio and visual information, and perform a relatively large vocabulary (approximately 1000 words speech recognition experiments. The experiments performed use clean audio data and audio data corrupted by stationary white Gaussian noise at various SNRs. The proposed system reduces the word error rate (WER by 20% to 23% relatively to audio-only speech recognition WERs, at various SNRs (0–30 dB with additive white Gaussian noise, and by 19% relatively to audio-only speech recognition WER under clean audio conditions.

Augmenting Environmental Interaction in Audio Feedback Systems

Directory of Open Access Journals (Sweden)

Seunghun Kim

2016-04-01

Full Text Available Audio feedback is defined as a positive feedback of acoustic signals where an audio input and output form a loop, and may be utilized artistically. This article presents new context-based controls over audio feedback, leading to the generation of desired sonic behaviors by enriching the influence of existing acoustic information such as room response and ambient noise. This ecological approach to audio feedback emphasizes mutual sonic interaction between signal processing and the acoustic environment. Mappings from analyses of the received signal to signal-processing parameters are designed to emphasize this specificity as an aesthetic goal. Our feedback system presents four types of mappings: approximate analyses of room reverberation to tempo-scale characteristics, ambient noise to amplitude and two different approximations of resonances to timbre. These mappings are validated computationally and evaluated experimentally in different acoustic conditions.

Active3 noise reduction

International Nuclear Information System (INIS)

Holzfuss, J.

1996-01-01

Noise reduction is a problem being encountered in a variety of applications, such as environmental noise cancellation, signal recovery and separation. Passive noise reduction is done with the help of absorbers. Active noise reduction includes the transmission of phase inverted signals for the cancellation. This paper is about a threefold active approach to noise reduction. It includes the separation of a combined source, which consists of both a noise and a signal part. With the help of interaction with the source by scanning it and recording its response, modeling as a nonlinear dynamical system is achieved. The analysis includes phase space analysis and global radial basis functions as tools for the prediction used in a subsequent cancellation procedure. Examples are given which include noise reduction of speech. copyright 1996 American Institute of Physics

Recognition of Voice Commands by Multisource ASR and Noise Cancellation in a Smart Home Environment

OpenAIRE

Vacher , Michel; Lecouteux , Benjamin; Portet , François

2012-01-01

International audience; In this paper, we present a multisource ASR system to detect home automation orders in various everyday listening conditions in a realistic home. The system is based on a state of the art echo cancellation stage that feeds recently introduced ASR techniques. The evaluation was conducted on a realistic noisy data set acquired in a smart home where a microphone was placed near the noise source and several other microphones were placed in different rooms. This distant spe...

Evaluation of State-of-the-Art Acoustic Feedback Cancellation Systems for Hearing Aids

DEFF Research Database (Denmark)

Guo, Meng; Jensen, Søren Holdt; Jensen, Jesper

2013-01-01

This research evaluates four state-of-the-art acoustic feedback cancellation systems in hearing aids in terms of the cancellation performance, sound quality degradation, and computational complexity. The authors compared a traditional full-band system to a system with a prediction error method...... in a full band, a subband system, a subband system with frequency shifting, and a recently proposed subband system with a novel probe noise deployment. All systems outperformed the traditional full-band system in cancellation performance, especially the subband system with probe noise is most effective...... for cancellation. However, in all cases there was a trade-off between performance and computational cost. With a 3-times increase in computation load, the probe noise based cancellation system can be realized that functions even in the most challenging feedback situation....

Reducing the Effects of Background Noise during Auditory Functional Magnetic Resonance Imaging of Speech Processing: Qualitative and Quantitative Comparisons between Two Image Acquisition Schemes and Noise Cancellation

Science.gov (United States)

Blackman, Graham A.; Hall, Deborah A.

2011-01-01

Purpose: The intense sound generated during functional magnetic resonance imaging (fMRI) complicates studies of speech and hearing. This experiment evaluated the benefits of using active noise cancellation (ANC), which attenuates the level of the scanner sound at the participant's ear by up to 35 dB around the peak at 600 Hz. Method: Speech and…

Observation of motorcycle helmet use rates in Michigan after partial repeal of the universal motorcycle helmet law.

Science.gov (United States)

Buckley, Lisa; Bingham, C Raymond; Flannagan, Carol A; Carter, Patrick M; Almani, Farideh; Cicchino, Jessica B

2016-10-01

Motorcycle crashes result in a significant health burden, including many fatal injuries and serious non-fatal head injuries. Helmets are highly effective in preventing such trauma, and jurisdictions that require helmet use of all motorcyclists have higher rates of helmet use and lower rates of head injuries among motorcyclists. The current study examines helmet use and characteristics of helmeted operators and their riding conditions in Michigan, following a weakening of the state's universal motorcycle helmet use law in April 2012. Data on police-reported crashes occurring during 2012-14 and from a stratified roadside observational survey undertaken in Southeast Michigan during May-September 2014 were used to estimate statewide helmet use rates. Observed helmet use was more common among operators of sports motorcycles, on freeways, and in the morning, and least common among operators of cruisers, on minor arterials, and in the afternoon. The rate of helmet use across the state was estimated at 75%, adjusted for roadway type, motorcycle class, and time of day. Similarly, the helmet use rate found from examination of crash records was 73%. In the observation survey, 47% of operators wore jackets, 94% wore long pants, 54% wore boots, and 80% wore gloves. Protective clothing of jackets and gloves was most often worn by sport motorcycle operators and long pants and boots most often by riders of touring motorcycles. Findings highlight the much lower rate of helmet use in Michigan compared with states that have a universal helmet use law, although the rate is higher than observed in many states with partial helmet laws. Targeted interventions aimed at specific groups of motorcyclists and situations where helmet use rates are particularly low should be considered to increase helmet use. Copyright © 2016 Elsevier Ltd. All rights reserved.

Intensity noise cancellation in solid-state laser at 1.5  μm using SHG depletion as a buffer reservoir.

Science.gov (United States)

Audo, Kevin; Alouini, Mehdi

2018-03-01

An absorption mechanism based on second-harmonic generation (SHG) is successfully implemented as a buffer reservoir in a solid-state Er,Yb:Glass laser emitting at the telecom wavelength. We show that a slight absorption mechanism based on SHG rate conversion of 0.016% using a beta barium borate crystal enables the canceling out of the excess intensity noise at the relaxation oscillation frequency, i.e., 35 dB reduction, as well as canceling the amplified spontaneous emission beating at the free spectral range resonances of the laser lying in the gigahertz range. Laser robustness is discussed.

Wiener variable step size and gradient spectral variance smoothing for double-talk-robust acoustic echo cancellation and acoustic feedback cancellation

DEFF Research Database (Denmark)

Gil-Cacho, Jose M.; Van Waterschoot, Toon; Moonen, Marc

2014-01-01

Double-talk (DT)-robust acoustic echo cancellation (AEC) and acoustic feedback cancellation (AFC) are needed in speech communication systems, e.g., in hands-free communication systems and hearing aids. In this paper, we derive a practical and computationally efficient algorithm based...... model and in colored non-stationary noise....

Analysis of Acoustic Feedback/Echo Cancellation in Multiple-Microphone and Single-Loudspeaker Systems Using a Power Transfer Function Method

DEFF Research Database (Denmark)

Guo, Meng; Bo Elmedyb, Thomas; Jensen, Søren Holdt

2011-01-01

In this work, we analyze a general multiple-microphone and single-loudspeaker audio processing system, where a multichannel adaptive system is used to cancel the effect of acoustic feedback/echo, and a beamformer processes the feedback/echo canceled signals. We introduce and derive an accurate...

A Microwave Photonic Interference Canceller: Architectures, Systems, and Integration

Science.gov (United States)

Chang, Matthew P.

This thesis is a comprehensive portfolio of work on a Microwave Photonic Self-Interference Canceller (MPC), a specialized optical system designed to eliminate interference from radio-frequency (RF) receivers. The novelty and value of the microwave photonic system lies in its ability to operate over bandwidths and frequencies that are orders of magnitude larger than what is possible using existing RF technology. The work begins, in 2012, with a discrete fiber-optic microwave photonic canceller, which prior work had demonstrated as a proof-of-concept, and culminates, in 2017, with the first ever monolithically integrated microwave photonic canceller. With an eye towards practical implementation, the thesis establishes novelty through three major project thrusts. (Fig. 1): (1) Extensive RF and system analysis to develop a full understanding of how, and through what mechanisms, MPCs affect an RF receiver. The first investigations of how a microwave photonic canceller performs in an actual wireless environment and a digital radio are also presented. (2) New architectures to improve the performance and functionality of MPCs, based on the analysis performed in Thrust 1. A novel balanced microwave photonic canceller architecture is developed and experimentally demonstrated. The balanced architecture shows significant improvements in link gain, noise figure, and dynamic range. Its main advantage is its ability to suppress common-mode noise and reduce noise figure by increasing the optical power. (3) Monolithic integration of the microwave photonic canceller into a photonic integrated circuit. This thrust presents the progression of integrating individual discrete devices into their semiconductor equivalent, as well as a full functional and RF analysis of the first ever integrated microwave photonic canceller.

Adaptive HIFU noise cancellation for simultaneous therapy and imaging using an integrated HIFU/imaging transducer.

Science.gov (United States)

Jeong, Jong Seob; Cannata, Jonathan Matthew; Shung, K Kirk

2010-04-07

It was previously demonstrated that it is feasible to simultaneously perform ultrasound therapy and imaging of a coagulated lesion during treatment with an integrated transducer that is capable of high intensity focused ultrasound (HIFU) and B-mode ultrasound imaging. It was found that coded excitation and fixed notch filtering upon reception could significantly reduce interference caused by the therapeutic transducer. During HIFU sonication, the imaging signal generated with coded excitation and fixed notch filtering had a range side-lobe level of less than -40 dB, while traditional short-pulse excitation and fixed notch filtering produced a range side-lobe level of -20 dB. The shortcoming is, however, that relatively complicated electronics may be needed to utilize coded excitation in an array imaging system. It is for this reason that in this paper an adaptive noise canceling technique is proposed to improve image quality by minimizing not only the therapeutic interference, but also the remnant side-lobe 'ripples' when using the traditional short-pulse excitation. The performance of this technique was verified through simulation and experiments using a prototype integrated HIFU/imaging transducer. Although it is known that the remnant ripples are related to the notch attenuation value of the fixed notch filter, in reality, it is difficult to find the optimal notch attenuation value due to the change in targets or the media resulted from motion or different acoustic properties even during one sonication pulse. In contrast, the proposed adaptive noise canceling technique is capable of optimally minimizing both the therapeutic interference and residual ripples without such constraints. The prototype integrated HIFU/imaging transducer is composed of three rectangular elements. The 6 MHz center element is used for imaging and the outer two identical 4 MHz elements work together to transmit the HIFU beam. Two HIFU elements of 14.4 mm x 20.0 mm dimensions could

Adaptive HIFU noise cancellation for simultaneous therapy and imaging using an integrated HIFU/imaging transducer

International Nuclear Information System (INIS)

Jeong, Jong Seob; Cannata, Jonathan Matthew; Shung, K Kirk

2010-01-01

It was previously demonstrated that it is feasible to simultaneously perform ultrasound therapy and imaging of a coagulated lesion during treatment with an integrated transducer that is capable of high intensity focused ultrasound (HIFU) and B-mode ultrasound imaging. It was found that coded excitation and fixed notch filtering upon reception could significantly reduce interference caused by the therapeutic transducer. During HIFU sonication, the imaging signal generated with coded excitation and fixed notch filtering had a range side-lobe level of less than -40 dB, while traditional short-pulse excitation and fixed notch filtering produced a range side-lobe level of -20 dB. The shortcoming is, however, that relatively complicated electronics may be needed to utilize coded excitation in an array imaging system. It is for this reason that in this paper an adaptive noise canceling technique is proposed to improve image quality by minimizing not only the therapeutic interference, but also the remnant side-lobe 'ripples' when using the traditional short-pulse excitation. The performance of this technique was verified through simulation and experiments using a prototype integrated HIFU/imaging transducer. Although it is known that the remnant ripples are related to the notch attenuation value of the fixed notch filter, in reality, it is difficult to find the optimal notch attenuation value due to the change in targets or the media resulted from motion or different acoustic properties even during one sonication pulse. In contrast, the proposed adaptive noise canceling technique is capable of optimally minimizing both the therapeutic interference and residual ripples without such constraints. The prototype integrated HIFU/imaging transducer is composed of three rectangular elements. The 6 MHz center element is used for imaging and the outer two identical 4 MHz elements work together to transmit the HIFU beam. Two HIFU elements of 14.4 mm x 20.0 mm dimensions could

Build Your Own Equiluminance Helmet

OpenAIRE

Connolly, Salammbo; Connolly, Denis; Cleary, Anne; Herman, Laura; Cavanagh, Patrick

2017-01-01

A wearable ?helmet? version of the S cone isolating technique was constructed to explore vision at equiluminance. For my high school summer science project, I visited parks and streets while wearing the helmet and report that the helmet appears to have captured the main properties described for the large-scale, more cumbersome stage version.

Motorcycle helmet use laws

Science.gov (United States)

2006-01-01

The National Highway Traffic Safety Administration (NHTSA) encourages States to enact legislation that requires all motorcycle riders to wear helmets. Motorcycle helmets provide the best protection from head injury for motorcyclists involved in traff...

Wideband Low Noise Amplifiers Exploiting Thermal Noise Cancellation

NARCIS (Netherlands)

Bruccoleri, F.; Klumperink, Eric A.M.; Nauta, Bram

2005-01-01

Low Noise Amplifiers (LNAs) are commonly used to amplify signals that are too weak for direct processing for example in radio or cable receivers. Traditionally, low noise amplifiers are implemented via tuned amplifiers, exploiting inductors and capacitors in resonating LC-circuits. This can render

Audio-Visual Speech Recognition Using Lip Information Extracted from Side-Face Images

Directory of Open Access Journals (Sweden)

Koji Iwano

2007-03-01

Full Text Available This paper proposes an audio-visual speech recognition method using lip information extracted from side-face images as an attempt to increase noise robustness in mobile environments. Our proposed method assumes that lip images can be captured using a small camera installed in a handset. Two different kinds of lip features, lip-contour geometric features and lip-motion velocity features, are used individually or jointly, in combination with audio features. Phoneme HMMs modeling the audio and visual features are built based on the multistream HMM technique. Experiments conducted using Japanese connected digit speech contaminated with white noise in various SNR conditions show effectiveness of the proposed method. Recognition accuracy is improved by using the visual information in all SNR conditions. These visual features were confirmed to be effective even when the audio HMM was adapted to noise by the MLLR method.

Helmet blastometer

Energy Technology Data Exchange (ETDEWEB)

Moss, William C; King, Michael J

2015-03-24

A helmet blastometer for characterizing the direction, speed, magnitude, and duration of a blast event to determine the likelihood of blast-induced traumatic brain injury (biTBI). Time of arrival (TOA) gage sensors are mounted on a rigid outer shell of the helmet each producing a TOA signal in response to a fast rising blast induced positive pressure change above a predetermined threshold. A receiver analyzes the positive pressure changes from the gages to determine direction, speed, and magnitude of a blast. Other TOA gauge sensors can be used to produce a TOA signal in response to a negative pressure change below a predetermined threshold. The positive and negative pressure change TOA signals are used to determine blast duration. A second set of internal contact pressure sensors is connected to an inner liner of the helmet to detect contact pressure on a user's head to determine if biTBI has been sustained.

Impact of Soldier Helmet Configuration on Survivability

Science.gov (United States)

2011-03-01

helmet cannot sit too low, which is evident when the helmet covers the eyebrows and the helmet interferes with eyewear . The helmet should remain in...agencies, academia, and private industry have also aided in model development. ORCA is a high-resolution computerized personnel casualty model that can

Federally mandating motorcycle helmets in the United States.

Science.gov (United States)

Eltorai, Adam E M; Simon, Chad; Choi, Ariel; Hsia, Katie; Born, Christopher T; Daniels, Alan H

2016-03-09

Motorcycle helmets reduce both motorcycle-related fatalities and head injuries. Motorcycle crashes are a major public health concern which place economic stress on the U.S. healthcare system. Although statewide universal motorcycle helmet laws effectively increase helmet use, most state helmet laws do not require every motorcycle rider to wear a helmet. Herein, we propose and outline the solution of implementing federal motorcycle helmet law, while addressing potential counterarguments. The decision to ride a motorcycle without a helmet has consequences that affect more than just the motorcyclist. In an effort to prevent unnecessary healthcare costs, injuries, and deaths, public health efforts to increase helmet use through education and legislation should be strongly considered. Helmet use on motorcycles fits squarely within the purview of the federal government public health and economic considerations.

On The Use of A Phase Modulation Method for Decorrelation in Acoustic Feedback Cancellation

DEFF Research Database (Denmark)

Guo, Meng; Jensen, Søren Holdt; Jensen, Jesper

2012-01-01

A major problem in using an adaptive filter in acoustic feedback cancellation systems is that the loudspeaker signal is correlated with the signals entering the microphones of the audio system, leading to biased filter estimates. One possible solution for reducing this problem is by means...... of decorrelation. In this work, we study a subband phase modulation method, which was originally proposed for decorrelation in multichannel acoustic echo cancellation systems. We determine if this method is effective for decorrelation in acoustic feedback cancellation systems by comparing it to a structurally...... similar frequency shifting decorrelation method. We show that the phase modulation method is suitable for decorrelation in a hearing aid acoustic feedback cancellation system, although the frequency shifting method is in general slightly more effective....

Optimized Audio Classification and Segmentation Algorithm by Using Ensemble Methods

Directory of Open Access Journals (Sweden)

Saadia Zahid

2015-01-01

Full Text Available Audio segmentation is a basis for multimedia content analysis which is the most important and widely used application nowadays. An optimized audio classification and segmentation algorithm is presented in this paper that segments a superimposed audio stream on the basis of its content into four main audio types: pure-speech, music, environment sound, and silence. An algorithm is proposed that preserves important audio content and reduces the misclassification rate without using large amount of training data, which handles noise and is suitable for use for real-time applications. Noise in an audio stream is segmented out as environment sound. A hybrid classification approach is used, bagged support vector machines (SVMs with artificial neural networks (ANNs. Audio stream is classified, firstly, into speech and nonspeech segment by using bagged support vector machines; nonspeech segment is further classified into music and environment sound by using artificial neural networks and lastly, speech segment is classified into silence and pure-speech segments on the basis of rule-based classifier. Minimum data is used for training classifier; ensemble methods are used for minimizing misclassification rate and approximately 98% accurate segments are obtained. A fast and efficient algorithm is designed that can be used with real-time multimedia applications.

An Embedded, Eight Channel, Noise Canceling, Wireless, Wearable sEMG Data Acquisition System With Adaptive Muscle Contraction Detection.

Science.gov (United States)

Ergeneci, Mert; Gokcesu, Kaan; Ertan, Erhan; Kosmas, Panagiotis

2018-02-01

Wearable technology has gained increasing popularity in the applications of healthcare, sports science, and biomedical engineering in recent years. Because of its convenient nature, the wearable technology is particularly useful in the acquisition of the physiological signals. Specifically, the (surface electromyography) sEMG systems, which measure the muscle activation potentials, greatly benefit from this technology in both clinical and industrial applications. However, the current wearable sEMG systems have several drawbacks including inefficient noise cancellation, insufficient measurement quality, and difficult integration to customized applications. Additionally, none of these sEMG data acquisition systems can detect sEMG signals (i.e., contractions), which provides a valuable environment for further studies such as human machine interaction, gesture recognition, and fatigue tracking. To this end, we introduce an embedded, eight channel, noise canceling, wireless, wearable sEMG data acquisition system with adaptive muscle contraction detection. Our design consists of two stages, which are the sEMG sensors and the multichannel data acquisition unit. For the first stage, we propose a low cost, dry, and active sEMG sensor that captures the muscle activation potentials, a data acquisition unit that evaluates these captured multichannel sEMG signals and transmits them to a user interface. In the data acquisition unit, the sEMG signals are processed through embedded, adaptive methods in order to reject the power line noise and detect the muscle contractions. Through extensive experiments, we demonstrate that our sEMG sensor outperforms a widely used commercially available product and our data acquisition system achieves 4.583 dB SNR gain with accuracy in the detection of the contractions.

The implementation of a municipal indoor ice skating helmet policy: effects on helmet use, participation and attitudes.

Science.gov (United States)

O'Mahony-Menton, Colleen; Willmore, Jacqueline; Russell, Katherine

2015-12-01

In Ottawa, between 2005 and 2009 there was an annual average of 47.2 head injuries due to ice skating in children and youth (1-19 years of age) requiring a visit to the emergency department, with the highest rates among those aged 5-14 years. Between 2002 and 2007, only 6% of children were wearing a helmet during ice skating when the head injury occurred. During indoor public skating sessions, 93% of children (skating helmet policy coupled with education and promotional activities on helmet use, participation and attitudes towards helmet use. An ice skating helmet policy for children (skating experience at indoor rinks during public skating sessions was developed, implemented and evaluated. Supportive activities such as discount coupons, promotional materials, a media launch, social marketing and staff training are described. The helmet policy was associated with increased helmet use for young children and for older children, youth and adults not included in the policy, without decreasing attendance to public skating sessions. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Investigation of signal models and methods for evaluating structures of processing telecommunication information exchange systems under acoustic noise conditions

Science.gov (United States)

Kropotov, Y. A.; Belov, A. A.; Proskuryakov, A. Y.; Kolpakov, A. A.

2018-05-01

The paper considers models and methods for estimating signals during the transmission of information messages in telecommunication systems of audio exchange. One-dimensional probability distribution functions that can be used to isolate useful signals, and acoustic noise interference are presented. An approach to the estimation of the correlation and spectral functions of the parameters of acoustic signals is proposed, based on the parametric representation of acoustic signals and the components of the noise components. The paper suggests an approach to improving the efficiency of interference cancellation and highlighting the necessary information when processing signals from telecommunications systems. In this case, the suppression of acoustic noise is based on the methods of adaptive filtering and adaptive compensation. The work also describes the models of echo signals and the structure of subscriber devices in operational command telecommunications systems.

Audio watermarking robust against D/A and A/D conversions

Directory of Open Access Journals (Sweden)

Xiang Shijun

2011-01-01

Full Text Available Abstract Digital audio watermarking robust against digital-to-analog (D/A and analog-to-digital (A/D conversions is an important issue. In a number of watermark application scenarios, D/A and A/D conversions are involved. In this article, we first investigate the degradation due to DA/AD conversions via sound cards, which can be decomposed into volume change, additional noise, and time-scale modification (TSM. Then, we propose a solution for DA/AD conversions by considering the effect of the volume change, additional noise and TSM. For the volume change, we introduce relation-based watermarking method by modifying groups of the energy relation of three adjacent DWT coefficient sections. For the additional noise, we pick up the lowest-frequency coefficients for watermarking. For the TSM, the synchronization technique (with synchronization codes and an interpolation processing operation is exploited. Simulation tests show the proposed audio watermarking algorithm provides a satisfactory performance to DA/AD conversions and those common audio processing manipulations.

Assessment of rural soundscapes with high-speed train noise.

Science.gov (United States)

Lee, Pyoung Jik; Hong, Joo Young; Jeon, Jin Yong

2014-06-01

In the present study, rural soundscapes with high-speed train noise were assessed through laboratory experiments. A total of ten sites with varying landscape metrics were chosen for audio-visual recording. The acoustical characteristics of the high-speed train noise were analyzed using various noise level indices. Landscape metrics such as the percentage of natural features (NF) and Shannon's diversity index (SHDI) were adopted to evaluate the landscape features of the ten sites. Laboratory experiments were then performed with 20 well-trained listeners to investigate the perception of high-speed train noise in rural areas. The experiments consisted of three parts: 1) visual-only condition, 2) audio-only condition, and 3) combined audio-visual condition. The results showed that subjects' preference for visual images was significantly related to NF, the number of land types, and the A-weighted equivalent sound pressure level (LAeq). In addition, the visual images significantly influenced the noise annoyance, and LAeq and NF were the dominant factors affecting the annoyance from high-speed train noise in the combined audio-visual condition. In addition, Zwicker's loudness (N) was highly correlated with the annoyance from high-speed train noise in both the audio-only and audio-visual conditions. © 2013.

Effects of repealing the motorcycle helmet law in Michigan.

Science.gov (United States)

Hothem, Zachary; Simon, Robert; Barnes, Wesley; Mohammad, Azmath; Sevak, Shruti; Ziegler, Kathryn; Iacco, Anthony; Janczyk, Randy

2017-09-01

In 2012, Michigan repealed its universal helmet law. Our study assessed the clinical impact of this repeal. Our trauma database was queried retrospectively for 2 motorcycle riding seasons before and 3 seasons after repeal. On-scene death data was obtained from the Medical Examiner. Helmet use in hospitalized patients decreased after the helmet law repeal. Non-helmeted patients had a significant increased rate of head injury. Non-helmeted patients were more likely to die during hospitalization. While, helmet use and drugs/alcohol status significantly affected the risk for head injury, only drug/alcohol had a significant effect on overall mortality. Following helmet law repeal, helmet use has decreased. Helmet status and drug/alcohol use was found to significantly increase risk of head injury. Although overall mortality was only affected by drug/alcohol use, non-helmeted patients did have a higher inpatient mortality. These findings deserve furthermore study and may provide a basis for reinstating the universal helmet law. Copyright © 2016 Elsevier Inc. All rights reserved.

Time Delay Mechanical-noise Cancellation (TDMC) to Provide Order of Magnitude Improvements in Radio Science Observations

Science.gov (United States)

Atkinson, D. H.; Babuscia, A.; Lazio, J.; Asmar, S.

2017-12-01

Many Radio Science investigations, including the determinations of planetary masses, measurements of planetary atmospheres, studies of the solar wind, and solar system tests of relativistic gravity, rely heavily on precision Doppler tracking. Recent and currently proposed missions such as VERITAS, Bepi Colombo, Juno have shown that the largest error source in the precision Doppler tracking data is noise in the Doppler system. This noise is attributed to un-modeled motions of the ground antenna's phase center and is commonly referred to as "antenna mechanical noise." Attempting to reduce this mechanical noise has proven difficult since the deep space communications antennas utilize large steel structures that are already optimized for mechanical stability. Armstrong et al. (2008) have demonstrated the Time Delay Mechanical-noise Cancellation (TDMC) concept using Goldstone DSN antennas (70 m & 34 m) and the Cassinispacecraft to show that the mechanical noise of the 70 m antenna could be suppressed when two-way Doppler tracking from the 70 m antenna and the receive-only Doppler data from the smaller, stiffer 34 m antenna were combined with suitable delays. The proof-of-concept confirmed that the mechanical noise in the final Doppler observable was reduced to that of the stiffer, more stable antenna. Caltech's Owens Valley Radio Observatory (OVRO) near Bishop, CA now has six 10.4 m diameter antennas, a consequence of the closure of Combined Array for Research in Millimeter Astronomy (CARMA). In principle, a 10 m antenna can lead to an order-of-magnitude improvement for the mechanical noise correction, as the smaller dish offers better mechanical stability compared to a DSN 34-m antenna. These antennas also have existing Ka-band receiving systems, and preliminary discussions with the OVRO staff suggest that much of the existing signal path could be used for Radio Science observations.

[Intermodal timing cues for audio-visual speech recognition].

Science.gov (United States)

Hashimoto, Masahiro; Kumashiro, Masaharu

2004-06-01

The purpose of this study was to investigate the limitations of lip-reading advantages for Japanese young adults by desynchronizing visual and auditory information in speech. In the experiment, audio-visual speech stimuli were presented under the six test conditions: audio-alone, and audio-visually with either 0, 60, 120, 240 or 480 ms of audio delay. The stimuli were the video recordings of a face of a female Japanese speaking long and short Japanese sentences. The intelligibility of the audio-visual stimuli was measured as a function of audio delays in sixteen untrained young subjects. Speech intelligibility under the audio-delay condition of less than 120 ms was significantly better than that under the audio-alone condition. On the other hand, the delay of 120 ms corresponded to the mean mora duration measured for the audio stimuli. The results implied that audio delays of up to 120 ms would not disrupt lip-reading advantage, because visual and auditory information in speech seemed to be integrated on a syllabic time scale. Potential applications of this research include noisy workplace in which a worker must extract relevant speech from all the other competing noises.

Motorcycle helmets in Vietnam: ownership, quality, purchase price, and affordability.

Science.gov (United States)

Hung, Dang Viet; Stevenson, Mark R; Ivers, Rebecca Q

2008-06-01

This study investigated motorcycle helmet ownership, quality, purchase price, and affordability in Vietnam. A random sample of motorcyclists was interviewed to investigate aspects of helmet ownership, the purchase price, and affordability of a motorcycle helmet. Multivariate modeling conducted to determine factors associated with the purchase price and affordability of motorcycle helmets. Helmet quality was assessed based on current legal requirements in Vietnam. The prevalence of helmet use in Vietnam remains low (23.3%) despite a high level of helmet ownership (94%), indicating that this is an important area for public health intervention. Overall the quality of helmets appeared to be good; however, few helmets displayed legally required information. Motorcyclists with a high income purchase more helmets for their household rather than more expensive helmets. To ensure that helmets are accessible to the community, policy-makers need to consider pricing motorcycle helmets at a price indicated by the results of this study. Prior to universal motorcycle helmet legislation, the government will also need to ensure that standard helmets are available and that enforcement is at a level to ensure that motorcycle helmets are actually used.

SAFETY ALERT: Electrical insulation defect on safety helmets

CERN Multimedia

HSE Unit

2013-01-01

Contrarily to the information provided until 31 May 2013, some “Euro Protection” safety helmets do not respect any of the requirements for electrical insulation.   This alert concerns the safety helmets identified under the following SCEM numbers: 50.43.30.050.4 white 50.43.30.060.2 yellow 50.43.30.070.0 blue This amounts up to several hundreds of helmets on the CERN site. People who need to wear an electrically insulated safety helmet for their activities, must from now on acquire a duly insulated item to be found on the CERN store under the following SCEM numbers: 50.43.30.210.6: Petzl Vertex ST Helmet (without vent) 50.43.30.300.1: IDRA Helmet with a visor for electrical work As for the people who do not need to wear an electrically insulated helmet for their activities, they can continue working with the aforementioned helmets. For your information, please take note of the maximum use limit of each helmet: “Euro Protection” Safety Helme...

A Small-Area Self-Biased Wideband CMOS Balun LNA with Noise Cancelling and Gain Enhancement

DEFF Research Database (Denmark)

Bruun, Erik; Andreani, Pietro; Custódio, J. R.

2010-01-01

In this paper we present a low-power and small-area balun LNA. The proposed inverter-based topology uses selfbiasing and noise cancelling, yielding a very robust LNA with a low NF. Comparing this circuit with a conventional inverterbased circuit, we obtain a ∼3 dB enhancement in voltage gain......, with improved robustness against PVT variations. Simulations results in a 130 nm CMOS technology show a 17.7dB voltage gain, nearly flat over a wide bandwidth (200MHz-1GHz), and an NF of approximately 4dB. The total power consumption is below 7.5 mW, with a very small die area of 0.007 mm2. All data...

Helmet-based physiological signal monitoring system.

Science.gov (United States)

Kim, Youn Sung; Baek, Hyun Jae; Kim, Jung Soo; Lee, Haet Bit; Choi, Jong Min; Park, Kwang Suk

2009-02-01

A helmet-based system that was able to monitor the drowsiness of a soldier was developed. The helmet system monitored the electrocardiogram, electrooculogram and electroencephalogram (alpha waves) without constraints. Six dry electrodes were mounted at five locations on the helmet: both temporal sides, forehead region and upper and lower jaw strips. The electrodes were connected to an amplifier that transferred signals to a laptop computer via Bluetooth wireless communication. The system was validated by comparing the signal quality with conventional recording methods. Data were acquired from three healthy male volunteers for 12 min twice a day whilst they were sitting in a chair wearing the sensor-installed helmet. Experimental results showed that physiological signals for the helmet user were measured with acceptable quality without any intrusions on physical activities. The helmet system discriminated between the alert and drowsiness states by detecting blinking and heart rate variability (HRV) parameters extracted from ECG. Blinking duration and eye reopening time were increased during the sleepiness state compared to the alert state. Also, positive peak values of the sleepiness state were much higher, and the negative peaks were much lower than that of the alert state. The LF/HF ratio also decreased during drowsiness. This study shows the feasibility for using this helmet system: the subjects' health status and mental states could be monitored without constraints whilst they were working.

Helmet Use and Head Injury in Homer's Iliad.

Science.gov (United States)

Swinney, Christian

2016-06-01

Homer's detailed descriptions of head injuries inflicted during the Trojan War are of particular interest to individuals in the medical community. Although studies have examined the prevalence of such injuries, none have examined the preventive measures taken to avoid them. An in-depth review of helmet use in Homer's Iliad was conducted to address this previously unexplored facet of the epic. An English translation of Homer's text was reviewed for all references to helmet use. The number of helmet references in each book was recorded, along with other pertinent details for each reference. There were 87 references to helmets (40 combat, 47 noncombat). The helmet belonged to a Greek warrior in 41 cases (47.1%), a Trojan warrior in 38 cases (43.6%), a divinity in 5 cases (5.7%), and a general group of warriors in 3 cases (3.4%). Helmet use provided protective benefit to Greek warriors at a rate of 30.0% (3 of 10) and Trojan warriors at a rate of 11.1% (2 of 18). This difference was not statistically significant (P = 0.23). The overall combined protective benefit of helmet use in the text was 17.9% (5 of 28). Helmets belonging to 15 specific Greek warriors and 18 specific Trojan warriors were referenced in the text. Helmets belonging to Hector (n = 12) and Achilles (n = 8) were most frequently mentioned. Helmet use and head injury both play a prominent role in Homer's Iliad. Helmets are frequently used in combat settings but with relatively little success. Helmets are also used in various noncombat settings. Copyright © 2016 Elsevier Inc. All rights reserved.

Linewidth-tolerant 10-Gbit/s 16-QAM transmission using a pilot-carrier based phase-noise cancelling technique.

Science.gov (United States)

Nakamura, Moriya; Kamio, Yukiyoshi; Miyazaki, Tetsuya

2008-07-07

We experimentally demonstrated linewidth-tolerant 10-Gbit/s (2.5-Gsymbol/s) 16-quadrature amplitude modulation (QAM) by using a distributed-feedback laser diode (DFB-LD) with a linewidth of 30 MHz. Error-free operation, a bit-error rate (BER) of noise canceling capability provided by a pilot-carrier and standard electronic pre-equalization to suppress inter-symbol interference (ISI) gave clear 16-QAM constellations and floor-less BER characteristics. We evaluated the BER characteristics by real-time measurement of six (three different thresholds for each I- and Q-component) symbol error rates (SERs) with simultaneous constellation observation.

Near-field Localization of Audio

DEFF Research Database (Denmark)

Jensen, Jesper Rindom; Christensen, Mads Græsbøll

2014-01-01

Localization of audio sources using microphone arrays has been an important research problem for more than two decades. Many traditional methods for solving the problem are based on a two-stage procedure: first, information about the audio source, such as time differences-of-arrival (TDOAs......) and gain ratios-of-arrival (GROAs) between microphones is estimated, and, second, this knowledge is used to localize the audio source. These methods often have a low computational complexity, but this comes at the cost of a limited estimation accuracy. Therefore, we propose a new localization approach......, where the desired signal is modeled using TDOAs and GROAs, which are determined by the source location. This facilitates the derivation of one-stage, maximum likelihood methods under a white Gaussian noise assumption that is applicable in both near- and far-field scenarios. Simulations show...

Motorcycle helmets: What about their coating?

Science.gov (United States)

Schnegg, Michaël; Massonnet, Geneviève; Gueissaz, Line

2015-07-01

In traffic accidents involving motorcycles, paint traces can be transferred from the rider's helmet or smeared onto its surface. These traces are usually in the form of chips or smears and are frequently collected for comparison purposes. This research investigates the physical and chemical characteristics of the coatings found on motorcycles helmets. An evaluation of the similarities between helmet and automotive coating systems was also performed.Twenty-seven helmet coatings from 15 different brands and 22 models were considered. One sample per helmet was collected and observed using optical microscopy. FTIR spectroscopy was then used and seven replicate measurements per layer were carried out to study the variability of each coating system (intravariability). Principal Component Analysis (PCA) and Hierarchical Cluster Analysis (HCA) were also performed on the infrared spectra of the clearcoats and basecoats of the data set. The most common systems were composed of two or three layers, consistently involving a clearcoat and basecoat. The coating systems of helmets with composite shells systematically contained a minimum of three layers. FTIR spectroscopy results showed that acrylic urethane and alkyd urethane were the most frequent binders used for clearcoats and basecoats. A high proportion of the coatings were differentiated (more than 95%) based on microscopic examinations. The chemical and physical characteristics of the coatings allowed the differentiation of all but one pair of helmets of the same brand, model and color. Chemometrics (PCA and HCA) corroborated classification based on visual comparisons of the spectra and allowed the study of the whole data set at once (i.e., all spectra of the same layer). Thus, the intravariability of each helmet and its proximity to the others (intervariability) could be more readily assessed. It was also possible to determine the most discriminative chemical variables based on the study of the PCA loadings. Chemometrics

An adaptive noise cancelling system used for beam control at the Stanford Linear Accelerator Center

International Nuclear Information System (INIS)

Himel, T.; Allison, S.; Grossberg, P.; Hendrickson, L.; Sass, R.; Shoaee, H.

1993-06-01

The SLAC Linear Collider now has a total of twenty-four beam-steering feedback loops used to keep the electron and positron beams on their desired trajectories. Seven of these loops measure and control the same beam as it proceeds down the linac through the arcs to the final focus. Ideally by each loop should correct only for disturbances that occur between it and the immediate upstream loop. In fact, in the original system each loop corrected for all upstream disturbances. This resulted in undesirable over-correction and ringing. We added MIMO (Multiple Input Multiple Output) adaptive noise cancellers to separate the signal we wish to correct from disturbances further upstream. This adaptive control improved performance in the 1992 run

Children and cycle helmets -- the case against.

Science.gov (United States)

McCarthy, M

1996-03-01

Much of the literature on child cycling accidents appears to blame the child as a victim, as though children's activities of playing and travelling were somehow wrong and that children are at fault when an adult drives a car over them. This adult-centred approach then leads to the idea that children should protect themselves with helmets, and that they are to blame if they are injured. However, adults who continue to hold the fantasy that helmets might be of value should know that the British Standard for cycle helmets protects only in a vertical fall of 1 m -- certainly not motor vehicle crashes. Thicker motor cycle helmets would give better protection but, of course, are heavier (and therefore unsaleable). Yet even with compulsory wearing helmets, more motor cyclists still die of head injuries than pedal cyclists. In the Newcastle study, five times as many child pedestrians died of road accidents as child cyclists. Convinced helmeteers should recommend all children playing or travelling in the streets to wear helmets (presumably heavy motor-cycle helmets). Slightly more sceptical proponents might prefer half of them -- in a randomized controlled trial. Car driving appears to have as serious health consequences as tobacco, alcohol and drugs, and to be as addictive (McCarthy 1992). Helmets are similar to filters in cigarettes -- they give the illusion of safety to both consumer and producer of the product, but the illusion is fatal. Yet, for their cardiovascular and mental health, children should have the freedom to cycle in safety around where they live. A profound change in the habits of adults is needed, rather than suits of armour for children.

Audio segmentation using Flattened Local Trimmed Range for ecological acoustic space analysis

Directory of Open Access Journals (Sweden)

Giovany Vega

2016-06-01

Full Text Available The acoustic space in a given environment is filled with footprints arising from three processes: biophony, geophony and anthrophony. Bioacoustic research using passive acoustic sensors can result in thousands of recordings. An important component of processing these recordings is to automate signal detection. In this paper, we describe a new spectrogram-based approach for extracting individual audio events. Spectrogram-based audio event detection (AED relies on separating the spectrogram into background (i.e., noise and foreground (i.e., signal classes using a threshold such as a global threshold, a per-band threshold, or one given by a classifier. These methods are either too sensitive to noise, designed for an individual species, or require prior training data. Our goal is to develop an algorithm that is not sensitive to noise, does not need any prior training data and works with any type of audio event. To do this, we propose: (1 a spectrogram filtering method, the Flattened Local Trimmed Range (FLTR method, which models the spectrogram as a mixture of stationary and non-stationary energy processes and mitigates the effect of the stationary processes, and (2 an unsupervised algorithm that uses the filter to detect audio events. We measured the performance of the algorithm using a set of six thoroughly validated audio recordings and obtained a sensitivity of 94% and a positive predictive value of 89%. These sensitivity and positive predictive values are very high, given that the validated recordings are diverse and obtained from field conditions. The algorithm was then used to extract audio events in three datasets. Features of these audio events were plotted and showed the unique aspects of the three acoustic communities.

Advanced Extravehicular Helmet Assembly, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — The current NASA spacesuit community is focusing on utilizing a 13" hemispherical helmet for the next generation of extravehicular activity spacesuits. This helmet...

Correlates and Barriers Associated with Motorcycle Helmet Use in Wa, Ghana.

Science.gov (United States)

Akaateba, Millicent Awialie; Yakubu, Ibrahim; Akanbang, Bernard Afiik Akanpabadai

2015-01-01

This study was conducted to investigate the correlates and barriers to helmet use among motorcycle riders in Wa, a motorcycle-predominant town in Ghana. An additional objective was to determine the association between helmet use and riders' knowledge, attitudes, and beliefs toward helmets. Cross-sectional surveys including both observation of helmet use and interviews were conducted among motorcycle riders at 6 randomly selected fuel stations and 4 motorcycle service centers within and outside the Central Business District of Wa. Questions covered riders' sociodemographic and riding characteristics, helmet use, reasons for use or nonuse of helmets, and knowledge, attitudes, and beliefs about helmets. Analyses were based on frequencies and testing of strength of association using adjusted odds ratios (with 95% confidence intervals) in binary logistic regression. The prevalence of helmet use among the 271 sampled riders was 46% (95% confidence interval [CI], 40.2-52.0). Gender, age, marital status, and occupation were significant sociodemographic correlates of helmet use in Wa. Compared to currently married riders, unmarried riders were 5 times less likely to use a helmet. No significant association existed between riders' educational attainment and helmet use. Helmet use was also positively correlated with helmet ownership and license holding. The leading reasons stated for helmet nonuse among nonusers were not traveling a long distance and helmets block vision and hearing. Protection from injury, legal requirement, and coping with the police for fear of being accosted for helmet nonuse were identified as common reasons for helmet use. Positive attitudes and beliefs were also significantly correlated with helmet use. Despite the existence of a legislation mandating the use of helmets on all roads as well as the high level of awareness among riders on this legislation and the benefits of helmets, the incidence of helmet use among motorists continue to be low in Wa

The mystery of the missing Viking helmets.

Science.gov (United States)

Wester, K

2000-11-01

Based on archaeological finds and old Norse literature, this study describes the Scandinavian helmet tradition from the Bronze Age to the Viking Age, as well as the Viking culture, with special emphasis on weaponry and head protection. Contrary to what is commonly believed, the study shows that metal helmets must have been used very infrequently by the Vikings. In fact, only one Viking helmet has been retrieved in Scandinavia. Possible reasons for the widespread misconception that the Vikings wore helmets are discussed, and the responsibility for not correcting this misunderstanding is placed with the archaeological profession.

Simulation-based assessment for construction helmets.

Science.gov (United States)

Long, James; Yang, James; Lei, Zhipeng; Liang, Daan

2015-01-01

In recent years, there has been a concerted effort for greater job safety in all industries. Personnel protective equipment (PPE) has been developed to help mitigate the risk of injury to humans that might be exposed to hazardous situations. The human head is the most vulnerable to impact as a moderate magnitude can cause serious injury or death. That is why industries have required the use of an industrial hard hat or helmet. There have only been a few articles published to date that are focused on the risk of head injury when wearing an industrial helmet. A full understanding of the effectiveness of construction helmets on reducing injury is lacking. This paper presents a simulation-based method to determine the threshold at which a human will sustain injury when wearing a construction helmet and assesses the risk of injury for wearers of construction helmets or hard hats. Advanced finite element, or FE, models were developed to study the impact on construction helmets. The FE model consists of two parts: the helmet and the human models. The human model consists of a brain, enclosed by a skull and an outer layer of skin. The level and probability of injury to the head was determined using both the head injury criterion (HIC) and tolerance limits set by Deck and Willinger. The HIC has been widely used to assess the likelihood of head injury in vehicles. The tolerance levels proposed by Deck and Willinger are more suited for finite element models but lack wide-scale validation. Different cases of impact were studied using LSTC's LS-DYNA.

Active noise cancellation of low frequency noise propagating in a duct

Directory of Open Access Journals (Sweden)

Farhad Forouharmajd

2012-01-01

Conclusions: With regard to the wide range of frequencies of different noise sources, having optimized circumstances in the duct, microphone location on the duct body or even the distance of the speakers may be important in signal processing, noise sampling and anti noise production.

Noise Depression of Parasitic Capacitance for Frequency Detection of Micromechanical Bulk Disk Resonator

DEFF Research Database (Denmark)

Tang, Meng; Cagliani, Alberto; Escouflaire, Marie

2010-01-01

the frequency noise of the system. A capacitor cancellation circuit is used to subtract the parasitic capacitor. Measurements are conducted before and after the cancellation, and results show that after cancellation, the anti resonance is suppressed and the frequency noise is decreased, thus decreasing...

Application of Auxetic Foam in Sports Helmets

Directory of Open Access Journals (Sweden)

Leon Foster

2018-03-01

Full Text Available This investigation explored the viability of using open cell polyurethane auxetic foams to augment the conformable layer in a sports helmet and improve its linear impact acceleration attenuation. Foam types were compared by examining the impact severity on an instrumented anthropomorphic headform within a helmet consisting of three layers: a rigid shell, a stiff closed cell foam, and an open cell foam as a conformable layer. Auxetic and conventional foams were interchanged to act as the helmet’s conformable component. Attenuation of linear acceleration was examined by dropping the combined helmet and headform on the front and the side. The helmet with auxetic foam reduced peak linear accelerations (p < 0.05 relative to its conventional counterpart at the highest impact energy in both orientations. Gadd Severity Index reduced by 11% for frontal impacts (38.9 J and 44% for side impacts (24.3 J. The conformable layer within a helmet can influence the overall impact attenuating properties. The helmet fitted with auxetic foam can attenuate impact severity more than when fitted with conventional foam, and warrants further investigation for its potential to reduce the risk of traumatic brain injuries in sport specific impacts.

Applications of digital processing for noise removal from plasma diagnostics

International Nuclear Information System (INIS)

Kane, R.J.; Candy, J.V.; Casper, T.A.

1985-01-01

The use of digital signal techniques for removal of noise components present in plasma diagnostic signals is discussed, particularly with reference to diamagnetic loop signals. These signals contain noise due to power supply ripple in addition to plasma characteristics. The application of noise canceling techniques, such as adaptive noise canceling and model-based estimation, will be discussed. The use of computer codes such as SIG is described. 19 refs., 5 figs

Injury outcome among helmeted and non-helmeted motorcycle ...

African Journals Online (AJOL)

users are vulnerable on the road and are at high risk of death resulting from head ..... time of injury sustained head injury reflecting its importance in prevention of head .... WHO (2006) Helmets: A Road Safety Manual for Decision-makers and ...

A study of emergency American football helmet removal techniques.

Science.gov (United States)

Swartz, Erik E; Mihalik, Jason P; Decoster, Laura C; Hernandez, Adam E

2012-09-01

The purpose was to compare head kinematics between the Eject Helmet Removal System and manual football helmet removal. This quasi-experimental study was conducted in a controlled laboratory setting. Thirty-two certified athletic trainers (sex, 19 male and 13 female; age, 33 ± 10 years; height, 175 ± 12 cm; mass, 86 ± 20 kg) removed a football helmet from a healthy model under 2 conditions: manual helmet removal and Eject system helmet removal. A 6-camera motion capture system recorded 3-dimensional head position. Our outcome measures consisted of the average angular velocity and acceleration of the head in each movement plane (sagittal, frontal, and transverse), the resultant angular velocity and acceleration, and total motion. Paired-samples t tests compared each variable across the 2 techniques. Manual helmet removal elicited greater average angular velocity in the sagittal and transverse planes and greater resultant angular velocity compared with the Eject system. No differences were observed in average angular acceleration in any single plane of movement; however, the resultant angular acceleration was greater during manual helmet removal. The Eject Helmet Removal System induced greater total head motion. Although the Eject system created more motion at the head, removing a helmet manually resulted in more sudden perturbations as identified by resultant velocity and acceleration of the head. The implications of these findings relate to the care of all cervical spine-injured patients in emergency medical settings, particularly in scenarios where helmet removal is necessary. Copyright © 2012 Elsevier Inc. All rights reserved.

Non-linear signal response functions and their effects on the statistical and noise cancellation properties of isotope ratio measurements by multi-collector plasma mass spectrometry

International Nuclear Information System (INIS)

Doherty, W.

2013-01-01

A nebulizer-centric response function model of the analytical inductively coupled argon plasma ion source was used to investigate the statistical frequency distributions and noise reduction factors of simultaneously measured flicker noise limited isotope ion signals and their ratios. The response function model was extended by assuming i) a single gaussian distributed random noise source (nebulizer gas pressure fluctuations) and ii) the isotope ion signal response is a parabolic function of the nebulizer gas pressure. Model calculations of ion signal and signal ratio histograms were obtained by applying the statistical method of translation to the non-linear response function model of the plasma. Histograms of Ni, Cu, Pr, Tl and Pb isotope ion signals measured using a multi-collector plasma mass spectrometer were, without exception, negative skew. Histograms of the corresponding isotope ratios of Ni, Cu, Tl and Pb were either positive or negative skew. There was a complete agreement between the measured and model calculated histogram skew properties. The nebulizer-centric response function model was also used to investigate the effect of non-linear response functions on the effectiveness of noise cancellation by signal division. An alternative noise correction procedure suitable for parabolic signal response functions was derived and applied to measurements of isotope ratios of Cu, Ni, Pb and Tl. The largest noise reduction factors were always obtained when the non-linearity of the response functions was taken into account by the isotope ratio calculation. Possible applications of the nebulizer-centric response function model to other types of analytical instrumentation, large amplitude signal noise sources (e.g., lasers, pumped nebulizers) and analytical error in isotope ratio measurements by multi-collector plasma mass spectrometry are discussed. - Highlights: ► Isotope ion signal noise is modelled as a parabolic transform of a gaussian variable. ► Flicker

77 FR 48105 - Federal Motor Vehicle Safety Standards; Motorcycle Helmets

Science.gov (United States)

2012-08-13

... [Docket No. NHTSA-2012-0112] Federal Motor Vehicle Safety Standards; Motorcycle Helmets AGENCY: National... Vehicle Safety Standard for motorcycle helmets. Specifically, the final rule amended the helmet labeling... compliance test procedures of FMVSS No. 218, Motorcycle helmets, in order to make it more difficult to...

Controlling kilometre-scale interferometric detectors for gravitational wave astronomy: Active phase noise cancellation using EOMs

International Nuclear Information System (INIS)

Arnaud, N.; Balembois, L.; Bizouard, M.A.; Brisson, V.; Casanueva, J.; Cavalier, F.; Davier, M.; Frey, V.; Hello, P.; Huet, D.; Leroy, N.; Loriette, V.; Maksimovic, I.; Robinet, F.

2017-01-01

The second generation of Gravitational waves detectors are kilometric Michelson interferometers with additional recycling Fabry–Perot cavities on the arms and ​the addition of two more recycling cavities to enhance their sensitivity, with the particularity that all the mirrors are suspended. In order to control them a new technique, based on the use of auxiliary lasers, has been developed to bring the interferometer to its working point, with all the cavities on their resonance, in an adiabatic way. The implementation of this technique in Advanced Virgo is under preparation and the propagation of a stable laser through a 3-km optical fibre is one of the most problematic issues. A new technique of active phase noise cancellation based on the use of Electro Optical Modulators has been developed, and a first prototype has been successfully tested.

Controlling kilometre-scale interferometric detectors for gravitational wave astronomy: Active phase noise cancellation using EOMs

Science.gov (United States)

Arnaud, N.; Balembois, L.; Bizouard, M. A.; Brisson, V.; Casanueva, J.; Cavalier, F.; Davier, M.; Frey, V.; Hello, P.; Huet, D.; Leroy, N.; Loriette, V.; Maksimovic, I.; Robinet, F.

2017-02-01

The second generation of Gravitational waves detectors are kilometric Michelson interferometers with additional recycling Fabry-Perot cavities on the arms and ​the addition of two more recycling cavities to enhance their sensitivity, with the particularity that all the mirrors are suspended. In order to control them a new technique, based on the use of auxiliary lasers, has been developed to bring the interferometer to its working point, with all the cavities on their resonance, in an adiabatic way. The implementation of this technique in Advanced Virgo is under preparation and the propagation of a stable laser through a 3-km optical fibre is one of the most problematic issues. A new technique of active phase noise cancellation based on the use of Electro Optical Modulators has been developed, and a first prototype has been successfully tested.

Controlling kilometre-scale interferometric detectors for gravitational wave astronomy: Active phase noise cancellation using EOMs

Energy Technology Data Exchange (ETDEWEB)

Arnaud, N.; Balembois, L.; Bizouard, M.A.; Brisson, V. [LAL, Univ. Paris-Sud, IN2P3/CNRS, Univ. Paris-Saclay, Orsay (France); Casanueva, J., E-mail: casanuev@lal.in2p3.fr [LAL, Univ. Paris-Sud, IN2P3/CNRS, Univ. Paris-Saclay, Orsay (France); Cavalier, F.; Davier, M.; Frey, V.; Hello, P.; Huet, D.; Leroy, N. [LAL, Univ. Paris-Sud, IN2P3/CNRS, Univ. Paris-Saclay, Orsay (France); Loriette, V.; Maksimovic, I. [ESPCI, CNRS, F-75005 Paris (France); Robinet, F. [LAL, Univ. Paris-Sud, IN2P3/CNRS, Univ. Paris-Saclay, Orsay (France)

2017-02-11

The second generation of Gravitational waves detectors are kilometric Michelson interferometers with additional recycling Fabry–Perot cavities on the arms and ​the addition of two more recycling cavities to enhance their sensitivity, with the particularity that all the mirrors are suspended. In order to control them a new technique, based on the use of auxiliary lasers, has been developed to bring the interferometer to its working point, with all the cavities on their resonance, in an adiabatic way. The implementation of this technique in Advanced Virgo is under preparation and the propagation of a stable laser through a 3-km optical fibre is one of the most problematic issues. A new technique of active phase noise cancellation based on the use of Electro Optical Modulators has been developed, and a first prototype has been successfully tested.

Ballistic Characterization Of A Typical Military Steel Helmet

Directory of Open Access Journals (Sweden)

Mohamed Ali Maher

2017-08-01

Full Text Available In this study the ballistic limit of a steel helmet against a FMJ 919 mm caliber bullet is estimated. The helmet model is the typical polish helmet wz.31.The helmet material showed high strength low alloy steel material of 0.28 carbon content and 9.125 kgm2 areal density. The tensile test according to ASTM E8 showed a tensile strength of 1236.4 MPa .The average hardness value was about HV550. First shooting experiment has been executed using a 9 mm pistol based on 350 ms muzzle velocity at 5m against the simply supported helmet complete penetrations rose in this test were in the form of cracks on the helmet surface and partial penetrations were in the form of craters on the surface whose largest diameter and depth were 43 mm and 20.2 mm consequently .The second experiment was on a rifled gun arrangement 13 bullets of 919 mm caliber were shot on the examined simply supported steel helmet at a zero obliquity angle at different velocities to determine the ballistic limit velocity V50 according to MIL-STD-662F. Three major outcomes were revealed 1 the value V50 which found to be about 390 ms is higher than the one found in literature 360 ms German steel helmet model 1A1. 2 The smallest the standard deviation of the mixed results zone data the most accurate the ballistic limit is. 3Similar to the performance of blunt-ended projectiles impacting overmatching targets tD near 11 or larger It was found that the dominating failure mode of the steel helmet stuck by a hemispherical-nose projectile was plugging mode despite of having tD ratio of about 19 undermatching.

Detection Of Alterations In Audio Files Using Spectrograph Analysis

Directory of Open Access Journals (Sweden)

Anandha Krishnan G

2015-08-01

Full Text Available The corresponding study was carried out to detect changes in audio file using spectrograph. An audio file format is a file format for storing digital audio data on a computer system. A sound spectrograph is a laboratory instrument that displays a graphical representation of the strengths of the various component frequencies of a sound as time passes. The objectives of the study were to find the changes in spectrograph of audio after altering them to compare altering changes with spectrograph of original files and to check for similarity and difference in mp3 and wav. Five different alterations were carried out on each audio file to analyze the differences between the original and the altered file. For altering the audio file MP3 or WAV by cutcopy the file was opened in Audacity. A different audio was then pasted to the audio file. This new file was analyzed to view the differences. By adjusting the necessary parameters the noise was reduced. The differences between the new file and the original file were analyzed. By adjusting the parameters from the dialog box the necessary changes were made. The edited audio file was opened in the software named spek where after analyzing a graph is obtained of that particular file which is saved for further analysis. The original audio graph received was combined with the edited audio file graph to see the alterations.

Applications of adaptive filters in active noise control

Science.gov (United States)

Darlington, Paul

The active reduction of acoustic noise is achieved by the addition of a cancelling acoustic signal to the unwanted sound. Successful definition of the cancelling signal amounts to a system identification problem. Recent advances in adaptive signal processing have allowed this problem to be tackled using adaptive filters, which offer significant advantages over conventional solutions. The extension of adaptive noise cancelling techniques, which were developed in the electrical signal conditioning context, to the control of acoustic systems is studied. An analysis is presented of the behavior of the Widrow-Hoff LMS adaptive noise canceller with a linear filter in its control loop. The active control of plane waves propagating axially in a hardwalled duct is used as a motivating model problem. The model problem also motivates the study of the effects of feedback around an LMS adaptive filter. An alternative stochastic gradient algorithm for controlling adaptive filters in the presence of feedback is presented.

Multiple-energy tissue-cancellation applications of a digital beam attenuator to chest radiography

International Nuclear Information System (INIS)

Dobbins, J.T. III.

1985-01-01

The digitally-formed primary beam attenuator (DBA) spatially modulates the x-ray fluence incident upon the patient to selectively attenuate regions of interest. The DBA attenuating mask is constructed from CeO 2 powder by a modified printing technique and uses image information from an initial low-dose exposure. Two tissue-cancellation imaging techniques are investigated with the DBA: (1) energy-dependent information is used to form a beam attenuator that attenuates specific tissues in the primary x-ray beam for tissue-cancelled film radiography; (2) the beam attenuator is used to improve image signal-to-noise and scattered radiation properties in traditional energy-subtraction tissue-cancellation imaging with digital detectors. The tissue-cancellation techniques in the primary x-ray beam were capable of adequately removing either soft-tissue or bone from the final compensated film radiograph when using a phantom with well defined soft-tissue and bone sections. However, when tried on an anthropomorphic chest phantom the results were adequate for cancellation of large soft tissue structures, but unsatisfactory for cancellation of bony structures such as the ribs, because of the limited spatial frequency content of the attenuating mask. The second technique (with digital detectors) showed improved uniformity of image signal-to-noise and a two-fold increase in soft-tissue nodule contrast due to improved scattered radiation properties. The tissue-cancelled images contained residual image contributions from the presence of the attenuating mask, but this residual may be correctable by future algorithms

Investigation on the applicability of dust protection helmets in the mining industry. Untersuchungen ueber die Einsatzmoeglichkeiten von Staubschutzhelmen im Bergbau

Energy Technology Data Exchange (ETDEWEB)

Bauer, H.D.; Werner, W.; Fuerst, E.

1984-10-01

In case of static ambient air, leakages for volumes of 25 x 1,5 l/min and air supplies >= 120 l/min or 25 x 2,0 l/min and >= 160 l/min do not occur. The increasing flow rate of moving ambient air leads to an increase of leakages. They show their largest extensions in case of lateral flow. In addition, they expand together with increasing physiological load. Therefore, the inherent air supply should not be below 160 l/min. The comparison of the dust protection helmet 'Airstream AH 1' with two respirators revealed the lowest additional physiological load for the dust protection helmet. Applicability tests in situ resulted in the following principal objections: contamination and scratches on the visor leading to visibility restriction of the wearer, bad fit, weight distribution and helmet dimensions, pressure sores and chafes of sealing parts and edges, lamp installation. Air supply and movement were felt as too high in case of low ambient temperatures, and in case of high temperatures and physiological strain it was considered as too low. There were only few objections against fan noise, weight and impediment by cable and battery. Based on the results, a specification including monitoring and maintenance of the helmet was made and additional tests for DIN design 58 645, item 7, were induced. Furthermore, a proposal regarding helmet optimisation was made.

Design and implementation of efficient low complexity biomedical artifact canceller for nano devices

Directory of Open Access Journals (Sweden)

Md Zia Ur RAHMAN

2016-07-01

Full Text Available In the current day scenario, with the rapid development of communication technology remote health care monitoring becomes as an intense research area. In remote health care monitoring, the primary aim is to facilitate the doctor with high resolution biomedical data. In order to cancel various artifacts in clinical environment in this paper we propose some efficient adaptive noise cancellation techniques. To obtain low computational complexity we combine clipping the data or error with Least Mean Square (LMS algorithm. This results sign regressor LMS (SRLMS, sign LMS (SLMS and sign LMS (SSLMS algorithms. Using these algorithms, we design Very-large-scale integration (VLSI architectures of various Biomedical Noise Cancellers (BNCs. In addition, the filtering capabilities of the proposed implementations are measured using real biomedical signals. Among the various BNCs tested, SRLMS based BNC is found to be better with reference to convergence speed, filtering capability and computational complexity. The main advantage of this technique is it needs only one multiplication to compute next weight. In this manner SRLMS based BNC is independent of filter length with reference to its computations. Whereas, the average signal to noise ratio achieved in the noise cancellation experiments are recorded as 7.1059dBs, 7.1776dBs, 6.2795dBs and 5.8847dBs for various BNCs based on LMS, SRLMS, SLMS and SSSLMS algorithms respectively. Based on the filtering characteristics, convergence and computational complexity, the proposed SRLMS based BNC architecture is well suited for nanotechnology applications.

Head and Helmet Biodynamics and Tracking Performance in Vibration Environments

National Research Council Canada - National Science Library

Smith, Suzanne D; Smith, Jeanne A

2006-01-01

...) and Up (40" elevation, 0" azimuth)], and three helmet CCs were tested. The overall head, helmet, and helmet slippage displacement rotations, and rms tracking error and percent time-on-target were evaluated...

Helmet Sensor - Transfer Function and Model Development

Science.gov (United States)

2010-09-01

that helmets be examined forensically when estimating the impact direction and location and the electronic HMSS data not be used in that determination... forensic analysis of the helmet itself is therefore recommended to determine the direction and severity of the ballistic impact 5. The helmet shell does...ot83 HTI l ot 8J HT1 lot S ,HTt IOt S , HTI l otiH HTt lotSS HTt l vt85 HTI l o)t 85 HT1 Front Level Acceleration ~~,--~----~--,30’p~g

Associations between drug use and motorcycle helmet use in fatal crashes.

Science.gov (United States)

Rossheim, Matthew E; Wilson, Fernando; Suzuki, Sumihiro; Rodriguez, Mayra; Walters, Scott; Thombs, Dennis L

2014-01-01

Helmet use reduces mortality risk for motorcyclists, regardless of drug and alcohol use. However, the association between drug use and motorcycle helmet utilization is not well known. This study examines the relationship between drug use and motorcycle helmet use among fatally injured motorcycle riders. Using data from the 2005-2009 Fatality Analysis Reporting System (FARS), we examined the association between drug use and motorcycle helmet use in a multivariable logistic regression analysis of 9861 fatally injured motorcycle riders in the United States. For fatally injured motorcycle riders, use of alcohol, marijuana, or other drugs was associated with increased odds of not wearing a motorcycle helmet, controlling for the effects of state motorcycle helmet laws and other confounding variables. Predicted probabilities indicate that helmet use substantially decreases among fatally injured riders mixing alcohol with marijuana and other drugs. Furthermore, the likelihood of helmet use between marijuana-only users and other drug users is virtually the same across all blood alcohol content (BAC) levels. This study provides evidence that alcohol, marijuana, and other drug use is associated with not wearing a motorcycle helmet in fatal motorcycle crashes. There is a clear need for additional prevention and intervention efforts that seek to change helmet and drug use norms among motorcycle riders.

Adaptive Beamforming Algorithms for Tow Ship Noise Canceling

NARCIS (Netherlands)

Robert, M.K.; Beerens, S.P.

2002-01-01

In towed array sonar, the directional noise originating from the tow ship, mainly machinery and hydrodynamic noise, often limits the sonar performance. When processed with classical beamforming techniques, loud tow ship noise induces high sidelobes that may hide detection of quiet targets in forward

Helmet wearing in Kenya: prevalence, knowledge, attitude, practice and implications.

Science.gov (United States)

Bachani, A M; Hung, Y W; Mogere, S; Akunga, D; Nyamari, J; Hyder, A A

2017-03-01

In light of the increasing prevalence of motorcycles on Kenyan roads, there is a need to address the safety of individuals using this mode of transport. Helmet use has been proven to be effective in preventing head injuries and fatalities in the event of a crash. This study aims to understand the prevalence of helmet use as well as knowledge, attitudes, and practices in two districts in Kenya over a 5-year period (2010-2014). Observational studies on helmet use at randomly selected locations throughout each district were done every quarter to estimate the prevalence of helmet use. Roadside knowledge, attitude, and practice (KAP) surveys were done two times a year in each district. Helmet use among motorcycle drivers and passengers in Thika and Naivasha was assessed through systematic observations at randomly selected locations in the two districts between August 2010 and December 2014. Roadside KAP surveys were administered in both sites to motorcyclists in areas where they stopped, including motorcycle bays, petrol stations and rest areas near the helmet observation sites. Secondary analysis of trauma registries was also used. Negative binomial regressions were used to assess trends of helmet wearing among motorcyclists over time, and logistic regressions were used to analyze associated risk factors as well as association with health outcomes among those admitted to the four hospitals. A total of 256,851 motorcycles were observed in the two target districts during the study period. Overall, prevalence of helmet use among motorcycle drivers in Thika and Naivasha across all periods was 35.12% (95% confidence interval [CI]: 34.87%-35.38%) and 37.42% (95% CI: 37.15%-37.69%) respectively. Prevalence of helmet wearing remained similar after the passage of a traffic amendment bill. These results were not statistically significant in either Thika or in Naivasha. Data from the KAP survey showed that respondents recognized the life-saving effect of wearing a helmet, but

How Satisfied are Soldiers with their Ballistic Helmets? A Comparison of Soldiers' Opinions about the Advanced Combat Helmet and the Personal Armor System for Ground Troops

National Research Council Canada - National Science Library

Ivins, Brian J; Schwab, Karen; Crowley, John S; McEntire, B. J; Trumble, Christopher C; Brown, Fred H; Warden, Deborah L

2008-01-01

.... These factors affect Soldiers' decisions about helmet use; therefore, rigorous research about Soldiers' real-life experiences with helmets is critical to assessing a helmet's overall protective efficacy...

What do we know about bicycle helmets?

NARCIS (Netherlands)

Bogerd, C.P. Halldin, P. Houtenbos, M. Otte, D. Rossi, R.M. Walker, L. Willinger, R. & Shinar, D.

2012-01-01

Cycling is an excellent sustainable alternative to driving for many journeys. But cyclists have fewer safety options than car-users, with a helmet being the main safety device that is available. However, there are indications that increasing bicycle helmet usage through legislation causes

Differential protective effects of motorcycle helmets against head injury.

Science.gov (United States)

Singleton, Michael D

2017-05-19

Although numerous observational studies have demonstrated a protective effect of motorcycle helmets against head injury, the degree of protection against specific head injury types remains unclear. Experimental biomechanics studies involving cadavers, animals, and computer models have established that head injuries have varying etiologies. This retrospective cross-sectional study compared helmet protection against skull fracture, cerebral contusion, intracranial hemorrhage, and cerebral concussion in a consecutive series of motorcycle operators involved in recent traffic crashes in Kentucky. Police collision reports linked to hospital inpatient and emergency department (ED) claims were analyzed for the period 2008 to 2012. Motorcycle operators with known helmet use who were not killed at the crash scene were included in the study. Helmet use was ascertained from the police report. Skull fracture, cerebral contusion, intracranial hemorrhage, and cerebral concussion were identified from International Classification of Diseases, Ninth Revision, Clinical Modification (ICD-9-CM) codes on the claims records. The relative risks of each type of head injury for helmeted versus unprotected operators were estimated using generalized estimating equations. Helmets offer substantial protection against skull fracture (relative risk [RR] = 0.31, 95% confidence interval [CI], 0.23, 0.34), cerebral contusion (RR = 0.29, 95% CI, 0.16, 0.53), and intracranial hemorrhage (RR = 0.47, 95% CI, 0.35, 0.63). The findings pertaining to uncomplicated concussion (RR = 0.80, 95% CI, 0.64, 1.01) were inconclusive. A modest protective effect (20% risk reduction) was suggested by the relative risk estimate, but the 95% confidence interval included the null value. Motorcycle helmets were associated with a 69% reduction in skull fractures, 71% reduction in cerebral contusion, and 53% reduction in intracranial hemorrhage. This study finds that current motorcycle helmets do not protect equally against

Helmet-induced headache among Danish military personnel.

Science.gov (United States)

Rahmani, Zakia; Kochanek, Aneta; Astrup, Jesper Johnsen; Poulsen, Jeppe Nørgaard; Gazerani, Parisa

2017-12-01

External compression headache is defined as a headache caused by an external physical compression applied on the head. It affects about 4% of the general population; however, certain populations (e.g. construction workers and military personnel) with particular needs of headwear or helmet are at higher risk of developing this type of headache. External compression headache is poorly studied in relation to specific populations. This study aimed to investigate the prevalence and pattern of helmet-induced external compression headache among Danish military personnel of the Northern Jutland region in Denmark. Data acquisition was based on a custom-made questionnaire delivered to volunteers who used helmets in the Danish military service and who agreed to participate in this study. The military of the Northern Jutland region of Denmark facilitated recruitment of the participants. The questionnaires were delivered on paper and the collected (anonymous) answers (total 279) were used for further analysis. About 30% of the study participants reported headache in relation to wearing a military helmet. Headache was defined as a pressing pain predominantly in the front of the head with an average intensity of 4 on a visual analogue scale of 0 (no pain) to 10 (worst pain imaginable). It was also found that helmets with different designs influenced both the occurrence of headache and its characteristics. This study is the first to demonstrate the prevalence and pattern of compression headache among military personnel in North Jutland, Denmark. The findings of this study call for further attention to helmet-induced external compression headache and strategies to minimize the burden.

The Effects of Motorcycle Helmet Legislation on Craniomaxillofacial Injuries.

Science.gov (United States)

Adams, Nicholas S; Newbury, Patrick A; Eichhorn, Mitchell G; Davis, Alan T; Mann, Robert J; Polley, John W; Girotto, John A

2017-06-01

Motorcycle helmet legislation has been a contentious topic for over a half-century. Benefits of helmet use in motorcycle trauma patients are well documented. In 2012, Michigan repealed its universal motorcycle helmet law in favor of a partial helmet law. The authors describe the early clinical effects on facial injuries throughout Michigan. Retrospective data from the Michigan Trauma Quality Improvement Program trauma database were evaluated. Included were 4643 motorcycle trauma patients presenting to 29 Level I and II trauma centers throughout Michigan 3 years before and after the law repeal (2009 to 2014). Demographics, external cause of injury codes, International Classification of Diseases, Ninth Revision diagnosis codes, and injury details were gathered. The proportion of unhelmeted trauma patients increased from 20 percent to 44 percent. Compared with helmeted trauma patients, unhelmeted patients were nearly twice as likely to sustain craniomaxillofacial injuries (relative risk, 1.90), including fractures (relative risk, 2.02) and soft-tissue injuries (relative risk, 1.94). Unhelmeted patients had a lower Glasgow Coma Scale score and higher Injury Severity Scores. Patients presenting after helmet law repeal were more likely to sustain craniomaxillofacial injuries (relative risk, 1.46), including fractures (relative risk, 1.28) and soft-tissue injuries (relative risk, 1.56). No significant differences were observed for age, sex, Injury Severity Score, or Glasgow Coma Scale score (p > 0.05). This study highlights the significant negative impact of relaxed motorcycle helmet laws leading to an increase in craniomaxillofacial injuries. The authors urge state and national legislators to reestablish universal motorcycle helmet laws.

Universal Motorcycle Helmet Laws to Reduce Injuries: A Community Guide Systematic Review.

Science.gov (United States)

Peng, Yinan; Vaidya, Namita; Finnie, Ramona; Reynolds, Jeffrey; Dumitru, Cristian; Njie, Gibril; Elder, Randy; Ivers, Rebecca; Sakashita, Chika; Shults, Ruth A; Sleet, David A; Compton, Richard P

2017-06-01

Motorcycle crashes account for a disproportionate number of motor vehicle deaths and injuries in the U.S. Motorcycle helmet use can lead to an estimated 42% reduction in risk for fatal injuries and a 69% reduction in risk for head injuries. However, helmet use in the U.S. has been declining and was at 60% in 2013. The current review examines the effectiveness of motorcycle helmet laws in increasing helmet use and reducing motorcycle-related deaths and injuries. Databases relevant to health or transportation were searched from database inception to August 2012. Reference lists of reviews, reports, and gray literature were also searched. Analysis of the data was completed in 2014. A total of 60 U.S. studies qualified for inclusion in the review. Implementing universal helmet laws increased helmet use (median, 47 percentage points); reduced total deaths (median, -32%) and deaths per registered motorcycle (median, -29%); and reduced total injuries (median, -32%) and injuries per registered motorcycle (median, -24%). Repealing universal helmet laws decreased helmet use (median, -39 percentage points); increased total deaths (median, 42%) and deaths per registered motorcycle (median, 24%); and increased total injuries (median, 41%) and injuries per registered motorcycle (median, 8%). Universal helmet laws are effective in increasing motorcycle helmet use and reducing deaths and injuries. These laws are effective for motorcyclists of all ages, including younger operators and passengers who would have already been covered by partial helmet laws. Repealing universal helmet laws decreased helmet use and increased deaths and injuries. Published by Elsevier Inc.

An inverter-based capacitive trans-impedance amplifier readout with offset cancellation and temporal noise reduction for IR focal plane array

Science.gov (United States)

Chen, Hsin-Han; Hsieh, Chih-Cheng

2013-09-01

This paper presents a readout integrated circuit (ROIC) with inverter-based capacitive trans-impedance amplifier (CTIA) and pseudo-multiple sampling technique for infrared focal plane array (IRFPA). The proposed inverter-based CTIA with a coupling capacitor [1], executing auto-zeroing technique to cancel out the varied offset voltage from process variation, is used to substitute differential amplifier in conventional CTIA. The tunable detector bias is applied from a global external bias before exposure. This scheme not only retains stable detector bias voltage and signal injection efficiency, but also reduces the pixel area as well. Pseudo-multiple sampling technique [2] is adopted to reduce the temporal noise of readout circuit. The noise reduction performance is comparable to the conventional multiple sampling operation without need of longer readout time proportional to the number of samples. A CMOS image sensor chip with 55×65 pixel array has been fabricated in 0.18um CMOS technology. It achieves a 12um×12um pixel size, a frame rate of 72 fps, a power-per-pixel of 0.66uW/pixel, and a readout temporal noise of 1.06mVrms (16 times of pseudo-multiple sampling), respectively.

Measurement of Gamma Knife registered helmet factors using MOSFETs

International Nuclear Information System (INIS)

Kurjewicz, Laryssa; Berndt, Anita

2007-01-01

The relative dose rate for the different Gamma Knife registered helmets (4, 8, 14, and 18 mm) is characterized by their respective helmet factors. Since the plateau of the dose profile for the 4 mm helmet is at most 1 mm wide, detector choices are limited. Traditionally helmet factors have been measured using 1x1x1 mm 3 thermoluminescent dosimeters (TLDs). However, these are time-consuming, cumbersome measurements. This article investigates the use of metal-oxide-semiconductor field effect transistors (MOSFETs) (active area of 0.2x0.2 mm 2 ) as a more accurate and convenient dosimeter. Their suitability for these measurements was confirmed by basic characterization measurements. Helmet factors were measured using both MOSFETs and the established TLD approach. A custom MOSFET cassette was designed in analogy to the Elekta TLD cassette (Elekta Instruments AB) for use with the Elekta dosimetry sphere. Although both dosimeters provided values within 3% of the manufacturer's suggestion, MOSFETs provided superior accuracy and precision, in a fraction of the time required for the TLD measurements. Thus, MOSFETs proved to be a reasonable alternative to TLDs for performing helmet factor measurements

Elimination of noise peak for signal processing in Johnson noise thermometry development

International Nuclear Information System (INIS)

Hwang, I. G.; Moon, B. S.; Jeong, J. E.; Jeo, Y. H.; Kisner, Roger A.

2003-01-01

The internal and external noise is the most considering obstacle in development of Johnson Noise Thermometry system. This paper addresses an external noise elimination issue of the Johnson Noise Thermometry system which is underway of development in collaboration between KAERI and ORNL. Although internal random noise is canceled by Cross Power Spectral Density function, a continuous wave penetrating into the electronic circuit is eliminated by the difference of peaks between Johnson signal and external noise. The elimination logic using standard deviation of CPSD and energy leakage problem in discrete CPSD function are discussed in this paper

Passengers' attitudes and behaviour towards motorcycle helmet use ...

African Journals Online (AJOL)

Passengers' attitudes and behaviour towards motorcycle helmet use in Ilorin, ... Remember me ... The purpose of this study was to examine the attitudes, knowledge, and behavior of motorcycle passengers to helmet use in Ilorin metropolis, ...

High phase noise tolerant pilot-tone-aided DP-QPSK optical communication systems

DEFF Research Database (Denmark)

Zhang, Xu; Pang, Xiaodan; Deng, Lei

2012-01-01

In this paper we experimentally demonstrate a novel, high phase-noise tolerant, optical dual polarization (DP) quadrature phase-shift keying (QPSK) communication system based on pilot-tone-aided phase noise cancellation (PNC) algorithm. Vertical cavity surface emitting lasers (VCSELs) with approx......In this paper we experimentally demonstrate a novel, high phase-noise tolerant, optical dual polarization (DP) quadrature phase-shift keying (QPSK) communication system based on pilot-tone-aided phase noise cancellation (PNC) algorithm. Vertical cavity surface emitting lasers (VCSELs...

A comparative evaluation of adaptive noise cancellation algorithms for minimizing motion artifacts in a forehead-mounted wearable pulse oximeter.

Science.gov (United States)

Comtois, Gary; Mendelson, Yitzhak; Ramuka, Piyush

2007-01-01

Wearable physiological monitoring using a pulse oximeter would enable field medics to monitor multiple injuries simultaneously, thereby prioritizing medical intervention when resources are limited. However, a primary factor limiting the accuracy of pulse oximetry is poor signal-to-noise ratio since photoplethysmographic (PPG) signals, from which arterial oxygen saturation (SpO2) and heart rate (HR) measurements are derived, are compromised by movement artifacts. This study was undertaken to quantify SpO2 and HR errors induced by certain motion artifacts utilizing accelerometry-based adaptive noise cancellation (ANC). Since the fingers are generally more vulnerable to motion artifacts, measurements were performed using a custom forehead-mounted wearable pulse oximeter developed for real-time remote physiological monitoring and triage applications. This study revealed that processing motion-corrupted PPG signals by least mean squares (LMS) and recursive least squares (RLS) algorithms can be effective to reduce SpO2 and HR errors during jogging, but the degree of improvement depends on filter order. Although both algorithms produced similar improvements, implementing the adaptive LMS algorithm is advantageous since it requires significantly less operations.

How motorcycle helmets affect trauma mortality: Clinical and policy implications.

Science.gov (United States)

Lee, Jwo-Leun; Chen, Tzu-Chun; Huang, Hung-Chang; Chen, Ray-Jade

2017-08-18

Motorcycles are the most popular vehicles in Taiwan, where more than 14.8 million motorcycles (1 motorcycle per 1.6 people) are in service. Despite the mandatory helmet law passed in 1997, less than 80% of motorcyclists in Taiwan wear helmets. The objective of this study was to analyze the effect of using motorcycle helmets on fatality rates. A clinical data set including 2,868 trauma patients was analyzed; the cross-sectional registration database was administered by a university medical center in Central Taiwan. A path analysis framework and multiple logistic regressions were used to estimate the marginal effect of helmet use on mortality. Using a helmet did not directly reduce the mortality rate but rather indirectly reduced the mortality rate through intervening variables such as the severity of head injuries, number of craniotomies, and complications during therapeutic processes. Wearing a helmet can reduce the fatality rate by 1.3%, the rate of severe head injury by 34.5%, the craniotomy rate by 7.8%, and the rate of complications during therapeutic processes by 1.5%. These rates comprise 33.3% of the mortality rate for people who do not wear helmets, 67.3% of the severe head injury rate, 60.0% of the craniotomy rate, and 12.2% of the rate of complications during therapeutic processes. Wearing a helmet and trauma system designation are crucial factors that reduce the fatality rate.

Does law enforcement awareness affect motorcycle helmet use? evidence from urban cities in Thailand.

Science.gov (United States)

Jiwattanakulpaisarn, Piyapong; Kanitpong, Kunnawee; Ponboon, Sattrawut; Boontob, Nuttapong; Aniwattakulchai, Pakorn; Samranjit, Supattra

2013-09-01

Although helmet use has been compulsory for motorcycle drivers and passengers in Thailand since the enactment of the Helmet Act in 1994, recent surveys show that the prevalence of helmet usage remains low, particularly among passengers. This paper has sought to explore motorcyclists' awareness of helmet law enforcement in Thailand and examine whether it affects their helmet use behaviour. A total of 2,429 drivers and 1,328 passengers in urban cities nationwide were interviewed in 2009, and the data were analysed using a multivariate ordered logit regression technique. About 60% of the drivers and only 28% of the passengers reported that they always wore a motorcycle helmet. Apart from basic demographics (i.e. age and gender) and riding frequency, our analysis reveals that the awareness of helmet law enforcement was among the contributing factors influencing the use of motorcycle helmets in Thailand. Regardless of riding position, the prevalence of helmet use tended to be greater among those frequently observing the police's checkpoints for helmet wearing and those perceiving the high risk of being caught for non-helmet use. However, the use of helmets appeared to be lower among drivers who perceived the checkpoints to take place at the same times and locations, which were likely predicted. For motorcycle passengers, it was found that the low prevalence of helmet use was potentially attributable to the absence of knowledge on the compulsory helmet law for passengers and the perception that the law was not enforced by the police. Thus, if motorcycle helmet use in Thailand is to be increased, considerable efforts need to be given to increasing the perceived risk of apprehension for non-helmet use (e.g. more police presence and random scheduling of enforcement activities), improving the awareness of the existing helmet law for passengers, and ensuring that helmet wearing by passengers is more strictly enforced.

Beamforming design with proactive interference cancelation in MISO interference channels

Science.gov (United States)

Li, Yang; Tian, Yafei; Yang, Chenyang

2015-12-01

In this paper, we design coordinated beamforming at base stations (BSs) to facilitate interference cancelation at users in interference networks, where each BS is equipped with multiple antennas and each user is with a single antenna. By assuming that each user can select the best decoding strategy to mitigate the interference, either canceling the interference after decoding when it is strong or treating it as noise when it is weak, we optimize the beamforming vectors that maximize the sum rate for the networks under different interference scenarios and find the solutions of beamforming with closed-form expressions. The inherent design principles are then analyzed, and the performance gain over passive interference cancelation is demonstrated through simulations in heterogeneous cellular networks.

Reduction of environmental MHz noise for SQUID application

Energy Technology Data Exchange (ETDEWEB)

Araya, T. [Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531 (Japan)]. E-mail: araya@sup.ee.es.osaka-u.ac.jp; Kitamura, Y. [Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531 (Japan); Kamishiro, M. [Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531 (Japan); Sakuta, K. [Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531 (Japan); Itozaki, H. [Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531 (Japan)]. E-mail: itozaki@ee.es.osaka-u.ac.jp

2006-10-01

It is important to remove large environmental noise in measurement using SQUIDs without magnetic shielding. Active noise control (ANC) is an effective method to remove the environmental noise. The environmental noise has been reduced by the ANC system in the radio frequency region around MHz. The anti-phase waves of the environmental noise should be generated by this system. The ANC system including the phase and amplitude control circuit was developed to make the anti-phase waves in the MHz region. In this paper, sinusoidal waves with a MHz frequency were used as the environmental noise. When a coil antenna was used for a receiver antenna, this ANC system suppressed these sinusoidal waves to the white noise level about 40 dB. When we used a SQUID as a receiver antenna, we also cancelled sinusoidal waves to the white noise level by this system. This shows that the ANC system is useful to reduce an environmental noise when this ANC system is developed to cancel multi-frequency noise.

Reduction of environmental MHz noise for SQUID application

International Nuclear Information System (INIS)

Araya, T.; Kitamura, Y.; Kamishiro, M.; Sakuta, K.; Itozaki, H.

2006-01-01

It is important to remove large environmental noise in measurement using SQUIDs without magnetic shielding. Active noise control (ANC) is an effective method to remove the environmental noise. The environmental noise has been reduced by the ANC system in the radio frequency region around MHz. The anti-phase waves of the environmental noise should be generated by this system. The ANC system including the phase and amplitude control circuit was developed to make the anti-phase waves in the MHz region. In this paper, sinusoidal waves with a MHz frequency were used as the environmental noise. When a coil antenna was used for a receiver antenna, this ANC system suppressed these sinusoidal waves to the white noise level about 40 dB. When we used a SQUID as a receiver antenna, we also cancelled sinusoidal waves to the white noise level by this system. This shows that the ANC system is useful to reduce an environmental noise when this ANC system is developed to cancel multi-frequency noise

Small signal audio design

CERN Document Server

Self, Douglas

2014-01-01

Learn to use inexpensive and readily available parts to obtain state-of-the-art performance in all the vital parameters of noise, distortion, crosstalk and so on. With ample coverage of preamplifiers and mixers and a new chapter on headphone amplifiers, this practical handbook provides an extensive repertoire of circuits that can be put together to make almost any type of audio system.A resource packed full of valuable information, with virtually every page revealing nuggets of specialized knowledge not found elsewhere. Essential points of theory that bear on practical performance are lucidly

Helmet Ownership and Use among Skateboarders: Utilisation of the Health Belief Model

Science.gov (United States)

Peachey, Andrew A.; Sutton, Debra L.; Cathorall, Michelle L.

2016-01-01

Introduction: The purpose of this study was to determine the proportion of skateboarders who owned and who wore a helmet and which constructs from the Health Belief Model predicted helmet ownership and helmet use among undergraduate skateboarders. Methods: From March 2013 through March 2014, 83 skateboarders completed a helmet attitude and use…

Camouflage design and head measurement characteristic of Indonesian armoured vehicle helmet

Science.gov (United States)

Sya'bana, Yukhi Mustaqim Kusuma; Sanjaya, K. H.

2017-01-01

In this paper discussed camouflage design helmet for armored vehicles with comparing head measurement of Indonesian anthropometric. Design process conduct with considering of design aspects involves function, materials, operational, technology, user, and appearance (camouflage). As an application of Indonesian National Army that qualifies factors needs: safety, comfort, practical and service. MIL-H-44099A Military Specification: Helmet, Ground Troops And Parachutists is minimum limitation standard of military helmet production. Head measurement for product design process guide is presented. Model simulation and helmet measurement using the design for ego and design for more types ergonomics concept. Appearance shape concept is engaging camouflage towards background and environment to deceive enemy viewpoint. Helmet prototype has tested ergonomically to an Indonesian National Army soldier and stated that the helmet size is a comfort and fitted on the head when in use.

''1/f noise'' in music: Music from 1/f noise

Energy Technology Data Exchange (ETDEWEB)

Voss, R.F.; Clarke, J.

1978-01-01

The spectral density of fluctuations in the audio power of many musical selections and of English speech varies approximately as 1/f (f is the frequency) down to a frequency of 5 x 10/sup -4/ Hz. This result implies that the audio-power fluctuations are correlated over all times in the same manner as ''1/f noise'' in electronic components. The frequency fluctuations of music also have a 1/f spectral density at frequencies down to the inverse of the length of the piece of music. The frequency fluctuations of English speech have a quite different behavior, with a single characteristic time of about 0.1 s, the average length of a syllable. The observations on music suggest that 1/f noise is a good choice for stochastic composition. Compositions in which the frequency and duration of each note were determined by 1/f noise sources sounded pleasing. Those generated by white-noise sources sounded too random, while those generated by 1/f/sup 2/ noise sounded too correlated.

Active cancellation of probing in linear dipole phased array

CERN Document Server

Singh, Hema; Jha, Rakesh Mohan

2015-01-01

In this book, a modified improved LMS algorithm is employed for weight adaptation of dipole array for the generation of beam pattern in multiple signal environments. In phased arrays, the generation of adapted pattern according to the signal scenario requires an efficient adaptive algorithm. The antenna array is expected to maintain sufficient gain towards each of the desired source while at the same time suppress the probing sources. This cancels the signal transmission towards each of the hostile probing sources leading to active cancellation. In the book, the performance of dipole phased array is demonstrated in terms of fast convergence, output noise power and output signal-to-interference-and noise ratio. The mutual coupling effect and role of edge elements are taken into account. It is established that dipole array along with an efficient algorithm is able to maintain multilobe beamforming with accurate and deep nulls towards each probing source. This work has application to the active radar cross secti...

Wavelet-based audio embedding and audio/video compression

Science.gov (United States)

Mendenhall, Michael J.; Claypoole, Roger L., Jr.

2001-12-01

Watermarking, traditionally used for copyright protection, is used in a new and exciting way. An efficient wavelet-based watermarking technique embeds audio information into a video signal. Several effective compression techniques are applied to compress the resulting audio/video signal in an embedded fashion. This wavelet-based compression algorithm incorporates bit-plane coding, index coding, and Huffman coding. To demonstrate the potential of this audio embedding and audio/video compression algorithm, we embed an audio signal into a video signal and then compress. Results show that overall compression rates of 15:1 can be achieved. The video signal is reconstructed with a median PSNR of nearly 33 dB. Finally, the audio signal is extracted from the compressed audio/video signal without error.

Harmonic Enhancement in Low Bitrate Audio Coding Using an Efficient Long-Term Predictor

Directory of Open Access Journals (Sweden)

Song Jeongook

2010-01-01

Full Text Available This paper proposes audio coding using an efficient long-term prediction method to enhance the perceptual quality of audio codecs to speech input signals at low bit-rates. The MPEG-4 AAC-LTP exploited a similar concept, but its improvement was not significant because of small prediction gain due to long prediction lags and aliased components caused by the transformation with a time-domain aliasing cancelation (TDAC technique. The proposed algorithm increases the prediction gain by employing a deharmonizing predictor and a long-term compensation filter. The look-back memory elements are first constructed by applying the de-harmonizing predictor to the input signal, then the prediction residual is encoded and decoded by transform audio coding. Finally, the long-term compensation filter is applied to the updated look-back memory of the decoded prediction residual to obtain synthesized signals. Experimental results show that the proposed algorithm has much lower spectral distortion and higher perceptual quality than conventional approaches especially for harmonic signals, such as voiced speech.

Increased resistance to sudden noise by audio stimulation during early ontogeny in German shepherd puppies.

Directory of Open Access Journals (Sweden)

Helena Chaloupková

Full Text Available The period of early ontogeny constitutes a time when the physical immaturity of an organism is highly susceptible to external stimuli. Thus, early development plays a major role in shaping later adult behavior. The aim of the study was to check whether stimulating puppies at this early stage in life with sound would improve their responsiveness towards unfamiliar noises during the selection process of the police behavioral test for puppies. The cohort comprised 37 puppies from the litters of three mothers. At the commencement of the experiment the dogs were aged 16 days, rising to the age of 32 days at its close. The mothers and litters of the treatment group were either exposed to radio broadcasts, (see below; three litters totaling 19 puppies, while the control group was not exposed to any radio programs (eight litters totaling 18 puppies. All three mothers had previously experienced both auditory circumstances, as described herein. Ordinary radio broadcasts were played to the puppies in the treatment group three times a day for 20 minute periods, always during feeding time. The cohort was subjected to the so-called Puppy Test, i.e. analysis of the potential of each animal, once the dogs had reached the age of 7 weeks. Such tests included exposure to a sudden noise caused by a shovel (100 dB, noise when alone in a room, and response to loud distracting stimuli (the latter two at 70 dB. Said tasks were rated by the same analyst on a scale of 0-5 points; the better the response of the dog, the higher the score given. The differences between the treatment and control groups were analyzed via Mixed Models (PROC MIXED in SAS. The animals comprising the treatment group responded with a higher score to the sudden noise caused by the shovel than the control dogs (P<0.01. Interestingly, gender was seen to affect response, with the males scoring more than the females (P<0.1. In conclusion, the results suggested that audio stimulation early in life

Imperfect generalized transmit beamforming with co-channel interference cancelation

KAUST Repository

Radaydeh, Redha Mahmoud Mesleh

2010-10-01

The performance of a generalized single-stream transmit beamforming scheme employing receive co-channel interference -steering algorithms in slowly varying and flat fading channels is analyzed. The impact of imperfect prediction of channel state information (CSI) for the desired user spatially uncorrelated transmit channels is considered. Both dominant interference cancelation and adaptive arbitrary interference cancelation algorithms for closely spaced receive antennas are used. The impact of outdated statistical ordering of the interferers instantaneous powers on the effectiveness of dominant interference cancelation is investigated against the less complex adaptive arbitrary cancelation scheme. For the system models described above, new exact formulas for the statistics of combined signal-to-interference-plus-noise ratio (SINR) are derived, from which results for conventional maximum ratio transmission (MRT) and best transmit channel selection schemes can be deduced as limiting cases. The results presented herein can be used to obtain quantitative measure for various performance metrics, and in addition to investigate the performance-complexity tradeoff for different multiple-antenna system models. © 2010 IEEE.

Long-term use of neonatal helmet-CPAP: a case report.

Science.gov (United States)

Doglioni, N; Micaglio, M; Zanardo, V; Trevisanuto, D

2009-12-01

In a recent short-term physiological study, we demonstrated a new continuous positive airway pressure (CPAP) system (neonatal helmet-CPAP) that could be a feasible device for managing preterm infants needing continuous distending pressure with better tolerability than nasal-CPAP. However, its application for a long-term period has never been reported in neonates. Here, we describe the use of neonatal helmet-CPAP in a neonate with persistent pulmonary hypertension of the newborn. Twenty minutes after neonatal helmet-CPAP placement, the baseline post-ductal tcSaO2 (66%) and alveolar-arterial gradient O2 improved from 66% and 648 mmHg to 100% and 465 mmHg, respectively. The neonatal helmet-CPAP was applied for 48 hours and was well-tolerated by the patient without complications. Long-term use of neonatal helmet-CPAP appears feasible and well-tolerated. Comparative trials are needed.

Paternalism & Its Discontents: Motorcycle Helmet Laws, Libertarian Values, and Public Health

Science.gov (United States)

Jones, Marian Moser; Bayer, Ronald

2007-01-01

The history of motorcycle helmet legislation in the United States reflects the extent to which concerns about individual liberties have shaped the public health debate. Despite overwhelming epidemiological evidence that motorcycle helmet laws reduce fatalities and serious injuries, only 20 states currently require all riders to wear helmets. During the past 3 decades, federal government efforts to push states toward enactment of universal helmet laws have faltered, and motorcyclists’ advocacy groups have been successful at repealing state helmet laws. This history raises questions about the possibilities for articulating an ethics of public health that would call upon government to protect citizens from their own choices that result in needless morbidity and suffering. PMID:17194856

Adaptive Noise Canceling Menggunakan Algoritma Least Mean Square (Lms)

OpenAIRE

Nardiana, Anita; Sumaryono, Sari Sujoko

2011-01-01

Noise is inevitable in communication system. In some cases, noise can disturb signal. It is veryannoying as the received signal is jumbled with the noise itself. To reduce or remove noise, filter lowpass,highpass or bandpass can solve the problems, but this method cannot reach a maximum standard. One ofthe alternatives to solve the problem is by using adaptive filter. Adaptive algorithm frequently used is LeastMean Square (LMS) Algorithm which is compatible to Finite Impulse Response (FIR). T...

Helmet use and associated factors among motorcyclists in the ...

African Journals Online (AJOL)

opperwjj

in Malaysia and the highest (10) in Brunei Duressalam. Stricter .... in line with the global findings that the introduction and enforcement of legislation on helmet .... Motorcycle helmet wearing behavior among Naresuan university students.

Prehospital emergency removal of football helmets using two techniques.

Science.gov (United States)

Swartz, Erik E; Hernandez, Adam E; Decoster, Laura C; Mihalik, Jason P; Burns, Matthew F; Reynolds, Cathryn

2011-01-01

To compare the Eject Helmet Removal (EHR) System with manual football helmet removal. This quasiexperimental counterbalanced study was conducted in a controlled laboratory setting. Thirty certified athletic trainers (17 men and 13 women; mean ± standard deviation age: 33.03 ± 10.02 years; height: 174.53 ± 12.04 cm; mass: 85.19 ± 19.84 kg) participated after providing informed consent. Participants removed a Riddell Revolution IQ football helmet from a healthy model two times each under two conditions: manual helmet removal (MHR) and removal with the EHR system. A six-camera, three-dimensional motion capture system was used to record range of motion (ROM) of the head. A digital stopwatch was used to time trials and to record a split time associated with EHR system bladder insertion. A modified Borg CR10 scale was used to measure the rating of perceived exertion (RPE). Mean values were created for each variable. Three pairwise t-tests with Bonferroni-corrected alpha levels tested for differences between time for removal, split time, and RPE. A 2 x 3 (condition x plane) totally within-subjects repeated-measures design analysis of variance (ANOVA) tested for differences in head ROM between the sagittal, frontal, and transverse planes. Analyses were performed using SPSS (version 18.0) (alpha = 0.05). There was no statistically significant difference in perceived difficulty between EHR (RPE = 2.73) and MHR (RPE = 2.55) (t(29) = 0.76; p = 0.45; d = 0.20). Manual helmet removal was, on average, 28.95 seconds faster than EHR (t(29) = 11.44; p football helmets and in helmets used in other sports such as lacrosse, motorsports, and ice hockey.

Aircrew helmet design and manufacturing enhancements through the use of advanced technologies

Science.gov (United States)

Cadogan, David P.; George, Alan E.; Winkler, Edward R.

1993-12-01

With the development of helmet mounted displays (HMD) and night vision systems (NVS) for use in military and civil aviation roles, new methods of helmet development need to be explored. The helmet must be designed to provide the user with the most lightweight, form fitting system, while meeting other system performance requirements. This can be achieved through a complete analysis of the system requirements. One such technique for systems analysis, a quality function deployment (QFD) matrix, is explored for this purpose. The advanced helmet development process for developing aircrew helmets includes the utilization of several emerging technologies such as laser scanning, computer aided design (CAD), computer generated patterns from 3-D surfaces, laser cutting of patterns and components, and rapid prototyping (stereolithography). Advanced anthropometry methods for helmet development are also available for use. Besides the application of advanced technologies to be used in the development of helmet assemblies, methods of mass reduction are also discussed. The use of these advanced technologies will minimize errors in the development cycle of the helmet and molds, and should enhance system performance while reducing development time and cost.

Nano-Composite Foam Sensor System in Football Helmets.

Science.gov (United States)

Merrell, A Jake; Christensen, William F; Seeley, Matthew K; Bowden, Anton E; Fullwood, David T

2017-12-01

American football has both the highest rate of concussion incidences as well as the highest number of concussions of all contact sports due to both the number of athletes and nature of the sport. Recent research has linked concussions with long term health complications such as chronic traumatic encephalopathy and early onset Alzheimer's. Understanding the mechanical characteristics of concussive impacts is critical to help protect athletes from these debilitating diseases and is now possible using helmet-based sensor systems. To date, real time on-field measurement of head impacts has been almost exclusively measured by devices that rely on accelerometers or gyroscopes attached to the player's helmet, or embedded in a mouth guard. These systems monitor motion of the head or helmet, but do not directly measure impact energy. This paper evaluates the accuracy of a novel, multifunctional foam-based sensor that replaces a portion of the helmet foam to measure impact. All modified helmets were tested using a National Operating Committee Standards for Athletic Equipment-style drop tower with a total of 24 drop tests (4 locations with 6 impact energies). The impacts were evaluated using a headform, instrumented with a tri-axial accelerometer, mounted to a Hybrid III neck assembly. The resultant accelerations were evaluated for both the peak acceleration and the severity indices. These data were then compared to the voltage response from multiple Nano Composite Foam sensors located throughout the helmet. The foam sensor system proved to be accurate in measuring both the HIC and Gadd severity index, as well as peak acceleration while also providing additional details that were previously difficult to obtain, such as impact energy.

Active Control of Fan Noise-Feasibility Study. Volume 2: Canceling Noise Source-Design of an Acoustic Plate Radiator Using Piezoceramic Actuators

Science.gov (United States)

Pla, F. G.; Rajiyah, H.

1995-01-01

The feasibility of using acoustic plate radiators powered by piezoceramic thin sheets as canceling sources for active control of aircraft engine fan noise is demonstrated. Analytical and numerical models of actuated beams and plates are developed and validated. An optimization study is performed to identify the optimum combination of design parameters that maximizes the plate volume velocity for a given resonance frequency. Fifteen plates with various plate and actuator sizes, thicknesses, and bonding layers were fabricated and tested using results from the optimization study. A maximum equivalent piston displacement of 0.39 mm was achieved with the optimized plate samples tested with only one actuator powered, corresponding to a plate deflection at the center of over 1 millimeter. This is very close to the deflection required for a full size engine application and represents a 160-fold improvement over previous work. Experimental results further show that performance is limited by the critical stress of the piezoceramic actuator and bonding layer rather than by the maximum moment available from the actuator. Design enhancements are described in detail that will lead to a flight-worthy acoustic plate radiator by minimizing actuator tensile stresses and reducing nonlinear effects. Finally, several adaptive tuning methods designed to increase the bandwidth of acoustic plate radiators are analyzed including passive, active, and semi-active approaches. The back chamber pressurization and volume variation methods are investigated experimentally and shown to be simple and effective ways to obtain substantial control over the resonance frequency of a plate radiator. This study shows that piezoceramic-based plate radiators can be a viable acoustic source for active control of aircraft engine fan noise.

Capabilities of Helmets for Preventing Head Injuries Induced by Ballistic Impacts

Directory of Open Access Journals (Sweden)

D.V. Balandin

2004-01-01

Full Text Available The limiting performance of ballistically loaded helmets designed to reduce head injuries is studied analytically. The projectile does not penetrate the helmet. This analysis evaluates the absolute minimum of the peak displacement of the helmet shell relative to the head, provided that criteria measuring the severity of head injuries lie within prescribed limits. Rather than optimize a specific design configuration, e.g. a viscoelastic foam liner, characteristics of a time-dependent force representing the helmet liner are calculated. The formulation reduces the limiting performance analysis to an optimal control problem.

Viet Nam’s mandatory motorcycle helmet law and its impact on children

Science.gov (United States)

Pervin, Aaron; Sidik, Mirjam; McKinley, Tyler; Tu, Nguyen Thi Hong; Nam, Nguyen Phuong

2009-01-01

Abstract Objective To measure the use of motorcycle helmets in children and to determine the reasons why children wear helmets less often than adults. Methods The frequency of helmet wearing among adults and children was ascertained by trained roadside observers, and randomized road user surveys were completed in four major centres in Viet Nam: Hanoi, Ho Chi Minh City, Can Tho and Da Nang. Survey data on key questions were cross tabulated, and χ² was calculated for significant differences between parents and non-parents (0.05). Findings The frequency of helmet use in the four study locations ranged from 90–99% among adults, from 15–53% among children ≤ 7 years of age, and from 38–53% among children > 7 but ≤ 14. Of the parents surveyed, 67% said the fear of neck injury was the most important reason their children did not wear a helmet. Conclusion Children wear motorcycle helmets much less often than adults. Legislation to penalize adults whose children do not wear motorcycle helmets has been proposed in Viet Nam. Furthermore, ongoing advocacy and social marketing efforts are being made to disseminate information about the safety benefits of helmets to combat erroneous public perceptions. PMID:19551255

In defence of mandatory bicycle helmet legislation: response to Hooper and Spicer.

Science.gov (United States)

Biegler, Paul; Johnson, Marilyn

2015-08-01

We invoke a triple rationale to rebut Hooper and Spicer's argument against mandatory helmet laws. First, we use the laws of physics and empirical studies to show how bicycle helmets afford substantial protection to the user. We show that Hooper and Spicer erroneously downplay helmet utility and that, as a result, their attack on the utilitarian argument for mandatory helmet laws is weakened. Next, we refute their claim that helmet legislation comprises unjustified paternalism. We show the healthcare costs of bareheaded riding to pose significant third party harms. It follows, we argue, that a utilitarian case for helmet laws can be sustained by appeal to Mill's Harm Principle. Finally, we reject Hooper and Spicer's claim that helmet laws unjustly penalise cyclists for their own health-affecting behaviour. Rather, we show their argument to suffer by disanalogy with medical cases where injustice may be more evident, for example, denial of bypass surgery to smokers. We conclude that mandatory helmet laws offer substantial utility and are entirely defensible within the framework of a liberal democracy. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Power Measurements for Microvision, Inc., Aircrew Integrated Helmet System Scanning Laser Helmet-Mounted Display

National Research Council Canada - National Science Library

Rash, Clarence

2002-01-01

...) technology based on scanning lasers. Under this program, Microvision, Inc., Bothell, Washington, has developed a scanning laser HMD prototype for use with the Aircrew Integrated Helmet System (AIHS...

Audio-Visual and Meaningful Semantic Context Enhancements in Older and Younger Adults.

Directory of Open Access Journals (Sweden)

Kirsten E Smayda

Full Text Available Speech perception is critical to everyday life. Oftentimes noise can degrade a speech signal; however, because of the cues available to the listener, such as visual and semantic cues, noise rarely prevents conversations from continuing. The interaction of visual and semantic cues in aiding speech perception has been studied in young adults, but the extent to which these two cues interact for older adults has not been studied. To investigate the effect of visual and semantic cues on speech perception in older and younger adults, we recruited forty-five young adults (ages 18-35 and thirty-three older adults (ages 60-90 to participate in a speech perception task. Participants were presented with semantically meaningful and anomalous sentences in audio-only and audio-visual conditions. We hypothesized that young adults would outperform older adults across SNRs, modalities, and semantic contexts. In addition, we hypothesized that both young and older adults would receive a greater benefit from a semantically meaningful context in the audio-visual relative to audio-only modality. We predicted that young adults would receive greater visual benefit in semantically meaningful contexts relative to anomalous contexts. However, we predicted that older adults could receive a greater visual benefit in either semantically meaningful or anomalous contexts. Results suggested that in the most supportive context, that is, semantically meaningful sentences presented in the audiovisual modality, older adults performed similarly to young adults. In addition, both groups received the same amount of visual and meaningful benefit. Lastly, across groups, a semantically meaningful context provided more benefit in the audio-visual modality relative to the audio-only modality, and the presence of visual cues provided more benefit in semantically meaningful contexts relative to anomalous contexts. These results suggest that older adults can perceive speech as well as younger

Finite element modelling of helmeted head impact under frontal ...

Indian Academy of Sciences (India)

helmets in direct impact are well documented and helmets have been found to ... conditions during a drop test and studied the influence of shell stiffness and liner ... the latter authors use a SI (Structural Intensity) approach to study power flow ...

Audio Papers

DEFF Research Database (Denmark)

Groth, Sanne Krogh; Samson, Kristine

2016-01-01

With this special issue of Seismograf we are happy to present a new format of articles: Audio Papers. Audio papers resemble the regular essay or the academic text in that they deal with a certain topic of interest, but presented in the form of an audio production. The audio paper is an extension...

The problem of the pillion rider: India's helmet law and New Delhi's exemption.

Science.gov (United States)

Swaroop, Mamta; Marie Siddiqui, Selma; Sagar, Sushma; Crandall, Marie L

2014-05-01

In India, motorized two-wheeler (MTW) road traffic accidents injure or kill 72,000 women annually. Before the Motor Vehicle Act of 1988, which required mandatory helmet use for MTW riders, a study found 0.6% of all MTW pillions (backseat passengers) were helmeted. Citing religious protests to the legislation, Delhi's high court exempted the city's 12 million women from the law. We hypothesize that currently male pillions use helmets more frequently than females, and that overall pillion helmet usage has increased over the last 20 y. Continuous video was recorded in half-hour blocks at four locations in Delhi on separate days, totaling 8 hours of high- and low-volume traffic. Videos were reviewed with at least two reviewers extracting the number of MTW pillions, as well as their gender, approximate age, and helmet usage. Of 4010 pillions identified, 63.8% were male, 32.4% female, and 3.3% children. Among males, there were significantly more helmeted pillions (88.4%, P < 0.001); among females, there were significantly more unhelmeted pillions (99.4%, P < 0.001). Among unhelmeted pillions, significantly more were female (81.4%) than male (P < 0.001). Current overall pillion helmet use is significantly higher than historical rate (P < 0.001). The significantly higher male pillion helmet usage compared with females indicates Delhi's helmet law is associated with increased compliance among those who fall under its jurisdiction. This augments the growing body of evidence that mandatory helmet laws are efficacious, thus repealing the exemption of women is an important step in increasing female pillion helmet usage. Copyright © 2014 Elsevier Inc. All rights reserved.

Speech Intelligibility with Helicopter Noise: Tests of Three Helmet-Mounted Communication Systems

National Research Council Canada - National Science Library

Ribera, John

2004-01-01

...) in background noise and reduce exposure to harmful levels of noise. Some aviators, over the course of their aviation career, develop noise-induced hearing loss that may affect their ability to perform required tasks...

Neck Muscle Fatigue Resulting from Prolonged Wear of Weighted Helmets

National Research Council Canada - National Science Library

Gallagher, Hilary L; Caldwell, Erin; ALbery, Christopher B

2008-01-01

.... While these systems undoubtedly increase a pilot's capabilities, one obvious drawback to putting all this equipment on the pilot's helmet is the increase in helmet weight that shifts the combined...

Paternalism and its discontents: motorcycle helmet laws, libertarian values, and public health.

Science.gov (United States)

Jones, Marian Moser; Bayer, Ronald

2007-02-01

The history of motorcycle helmet legislation in the United States reflects the extent to which concerns about individual liberties have shaped the public health debate. Despite overwhelming epidemiological evidence that motorcycle helmet laws reduce fatalities and serious injuries, only 20 states currently require all riders to wear helmets. During the past 3 decades, federal government efforts to push states toward enactment of universal helmet laws have faltered, and motorcyclists' advocacy groups have been successful at repealing state helmet laws. This history raises questions about the possibilities for articulating an ethics of public health that would call upon government to protect citizens from their own choices that result in needless morbidity and suffering.

Characteristics of helmet or knit cap use in head injury of snowboarders.

Science.gov (United States)

Fukuda, Osamu; Hirashima, Yutaka; Origasa, Hideki; Endo, Shunro

2007-11-01

The rate of head injury is 1.86-6 times higher for snowboarding than for skiing. Detailed data about the usefulness of a helmet or knit cap for protecting against serious head injuries have not been reported. The present study evaluated the use of a helmet or knit cap for preventing head injuries. Questionnaire data were collected from 1,190 consecutive patients in a hospital during the 1999/2000-2002/2003 winter seasons at Uonuma ski resort, Niigata, Japan. Patients were divided into the helmet, knit cap, and no cap groups. Upper technical level was highest and jumping as the cause of injury was most frequent in the helmet group. After adjustment for other confounders, there was a significant negative association between the occurrence of serious head injury during snowboarding and female sex (adjusted odds ratio 0.55, 95% confidence interval 0.421-0.718, p jumping (adjusted odds ratio 2.25, 95% confidence interval 1.48-3.43, p = 0.0001). Among snowboarding maneuvers, only jumping showed a significant negative association between wearing of a helmet or knit cap and the occurrence of serious head injury (p = 0.036). Snowboarders who wear helmets might attempt dangerous maneuvers causing injuries. Wearing of a helmet or knit cap protected against serious head injuries on jumping. Every snowboarder should wear a helmet or knit cap on jumping to prevent head injury.

High School Football Players Use Their Helmets to Tackle Other Players Despite Knowing the Risks.

Science.gov (United States)

Kuriyama, Andrew M; Nakatsuka, Austin S; Yamamoto, Loren G

2017-03-01

There is greater attention to head-related injuries and concussions in American football. The helmet's structural safety and the way that football players use their helmets are important in preventing head injuries. Current strategies include penalizing players for high-risk behavior such as leading with their helmet or hitting an opposing player above the shoulder. Passive strategies include helmet modification to better protect the head of the players or to change the playing style of the players. Hawai'i high school varsity football players were surveyed to determine how they use their helmets and how a new helmet design would affect their style of play. One hundred seventy-seven surveys were completed; 79% said that they used their helmet to hit an opposing player during a tackle and 46% said they made this contact intentionally. When asked about modifying helmets with a soft material on the outside, 48% said they thought putting a soft cover over a regular helmet would protect their head better. However, many participants said that putting a soft cover over their regular helmet was a bad idea for various reasons. Most young football players use their helmets to block or tackle despite being taught they would be penalized or potentially injured if they did so. By gaining a better understanding of why and how players use their helmets and how they would respond to new helmet designs, steps can be taken to reduce head injuries for all levels of play.

Wide-band CMOS low-noise amplifier exploiting thermal noise canceling

NARCIS (Netherlands)

Bruccoleri, F.; Klumperink, Eric A.M.; Nauta, Bram

Known elementary wide-band amplifiers suffer from a fundamental tradeoff between noise figure (NF) and source impedance matching, which limits the NF to values typically above 3 dB. Global negative feedback can be used to break this tradeoff, however, at the price of potential instability. In

The Influence of Friction Between Football Helmet and Jersey Materials on Force: A Consideration for Sport Safety.

Science.gov (United States)

Rossi, Anthony M; Claiborne, Tina L; Thompson, Gregory B; Todaro, Stacey

2016-09-01

The pocketing effect of helmet padding helps to dissipate forces experienced by the head, but if the player's helmet remains stationary in an opponent's shoulder pads, the compressive force on the cervical spine may increase. To (1) measure the coefficient of static friction between different football helmet finishes and football jersey fabrics and (2) calculate the potential amount of force on a player's helmet due to the amount of friction present. Cross-sectional study. Laboratory. Helmets with different finishes and different football jersey fabrics. The coefficient of friction was determined for 2 helmet samples (glossy and matte), 3 football jerseys (collegiate, high school, and youth), and 3 types of jersey numbers (silkscreened, sublimated, and stitched on) using the TAPPI T 815 standard method. These measurements determined which helmet-to-helmet, helmet-to-jersey number, and helmet-to-jersey material combination resulted in the least amount of static friction. The glossy helmet versus glossy helmet combination produced a greater amount of static friction than the other 2 helmet combinations (P = .013). The glossy helmet versus collegiate jersey combination produced a greater amount of static friction than the other helmet-to-jersey material combinations (P < .01). The glossy helmet versus silkscreened numbers combination produced a greater amount of static friction than the other helmet-to-jersey number combinations (P < .01). The force of static friction experienced during collisions can be clinically relevant. Conditions with higher coefficients of static friction result in greater forces. In this study, the highest coefficient of friction (glossy helmet versus silkscreened number) could increase the forces on the player's helmet by 3553.88 N when compared with other helmet-to-jersey combinations. Our results indicate that the makeup of helmet and uniform materials may affect sport safety.

Brain tissue analysis of impacts to American football helmets.

Science.gov (United States)

Post, Andrew; Kendall, Marshall; Cournoyer, Janie; Karton, Clara; Oeur, R Anna; Dawson, Lauren; Hoshizaki, T Blaine

2018-02-01

Concussion in American football is a prevalent concern. Research has been conducted examining frequencies, location, and thresholds for concussion from impacts. Little work has been done examining how impact location may affect risk of concussive injury. The purpose of this research was to examine how impact site on the helmet and type of impact, affects the risk of concussive injury as quantified using finite element modelling of the human head and brain. A linear impactor was used to impact a helmeted Hybrid III headform in several locations and using centric and non-centric impact vectors. The resulting dynamic response was used as input for the Wayne State Brain Injury Model to determine the risk of concussive injury by utilizing maximum principal strain as the predictive variable. The results demonstrated that impacts that occur primarily to the side of the head resulted in higher magnitudes of strain in the grey and white matter, as well as the brain stem. Finally, commonly worn American football helmets were used in this research and significant risk of injury was incurred for all impacts. These results suggest that improvements in American football helmets are warranted, in particular for impacts to the side of the helmet.

Local Control of Audio Environment: A Review of Methods and Applications

Directory of Open Access Journals (Sweden)

Jussi Kuutti

2014-02-01

Full Text Available The concept of a local audio environment is to have sound playback locally restricted such that, ideally, adjacent regions of an indoor or outdoor space could exhibit their own individual audio content without interfering with each other. This would enable people to listen to their content of choice without disturbing others next to them, yet, without any headphones to block conversation. In practice, perfect sound containment in free air cannot be attained, but a local audio environment can still be satisfactorily approximated using directional speakers. Directional speakers may be based on regular audible frequencies or they may employ modulated ultrasound. Planar, parabolic, and array form factors are commonly used. The directivity of a speaker improves as its surface area and sound frequency increases, making these the main design factors for directional audio systems. Even directional speakers radiate some sound outside the main beam, and sound can also reflect from objects. Therefore, directional speaker systems perform best when there is enough ambient noise to mask the leaking sound. Possible areas of application for local audio include information and advertisement audio feed in commercial facilities, guiding and narration in museums and exhibitions, office space personalization, control room messaging, rehabilitation environments, and entertainment audio systems.

Implementation of an all-ages mandatory helmet policy for ice skating.

Science.gov (United States)

Thibault-Halman, Ginette; Fenerty, Lynne; Wheadon-Hore, Kathie; Walling, Simon; Cusimano, Michael D; Clarke, David B

2015-12-01

Ice skaters sustain a significant number of head injuries each winter. We are the first to implement an all-ages helmet policy at a university-based Canadian arena. We report our experience from a cross-sectional observational study as well as the policy's consequences on helmet use and skating participation. Educational programming was provided prior to policy implementation. Observations of helmet use, falls and skater demographics were conducted prior to education/implementation and after policy implementation. The number of skaters observed was essentially unchanged by the policy; 361 skaters were observed pre-implementation, while 358 were observed post-implementation during the same number of observation-hours. Pre-implementation, helmet use ranged from 97% among children under 12 to 10% among adults; post-implementation use in all skaters was 99%. Falls were observed among all age groups, with preponderance among those aged 4-12. An all-ages helmet policy was successful both in achieving helmet use among all skaters and in maintaining participation rates. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Helmet Use and Associated Factors among Thai Motorcyclists during Songkran Festival

Science.gov (United States)

Siviroj, Penprapa; Peltzer, Karl; Pengpid, Supa; Morarit, Sompong

2012-01-01

The aim of this study was to assess helmet use and associated factors among motorcycle riders during Songkran festival in Thailand. A cross-sectional survey was conducted to determine the prevalence of helmet use among Thai motorcycle riders (sample size = 18,998) during four days of the Songkran festival. For this sample, the population of motorcycle riders was consecutively selected using quota sampling from 12 petrol stations in four provinces from each of the four main geographical regions of Thailand. The study was conducted at petrol stations at roads in town, outside town and highway at different time intervals when trained field staff administered a structured questionnaire and performed an observation checklist. Results indicate that 44.2% of the motorcycle riders and 72.5% of the motorcycle passengers had not been using a helmet. In multivariable analysis demographics, environmental factors, helmet use experiences and attitudes and recalling a lower exposure to road safety awareness (RSA) campaign were associated with non-helmet use among motorcyclists. It appears that the RSA campaign may have some positive effect on reducing non-helmet use among motorcycle riders during the Songkran festival. PMID:23202686

DETECTION OF MOTORCYCLISTS WITHOUT HELMET AND FINEPAYMENT USING OPEN CV

OpenAIRE

Stemy Simon, Divya Kumaran A.K.

2018-01-01

The helmet is the main safety equipment of motorcyclists, but many drivers do not use it. The main aim of this project is to construct an automatic detection of the motorcyclist without helmet from video using OpenCV library tools. If they are not wearing the helmet, the license plate of the motorcycle is focused automatically. By using Computer Vision technique we can detect and recognize the license plate number. We make the training set of different characters of different sizes. Based on ...

Proceedings of the 1986 international conference on noise control engineering. Volume 1

International Nuclear Information System (INIS)

Lotz, R.

1986-01-01

These proceedings collect papers on noise pollution. Topics include: noise sources, noise of chain conveyors in mining, control of noise sources in power plants, noise control elements, vibration, a method of noise control in a nuclear power plant, biological effects of noise, statistical audio dosimetry, and power house noise control

Tensorial dynamic time warping with articulation index representation for efficient audio-template learning.

Science.gov (United States)

Le, Long N; Jones, Douglas L

2018-03-01

Audio classification techniques often depend on the availability of a large labeled training dataset for successful performance. However, in many application domains of audio classification (e.g., wildlife monitoring), obtaining labeled data is still a costly and laborious process. Motivated by this observation, a technique is proposed to efficiently learn a clean template from a few labeled, but likely corrupted (by noise and interferences), data samples. This learning can be done efficiently via tensorial dynamic time warping on the articulation index-based time-frequency representations of audio data. The learned template can then be used in audio classification following the standard template-based approach. Experimental results show that the proposed approach outperforms both (1) the recurrent neural network approach and (2) the state-of-the-art in the template-based approach on a wildlife detection application with few training samples.

Psychological models for development of motorcycle helmet use among students in Vietnam

Science.gov (United States)

Kumphong, J.; Satiennam, T.; Satiennam, W.; Trinh, Tu Anh

2018-04-01

A helmet can reduce head accident severity. The aim of this research study was to study the intention for helmet use of students who ride motorcycles in Vietnam, by Structural Equation Modeling (SEM). Questionnaires developed by several traffic psychology modules, including the Theory of Planned Behaviour (TPB), Traffic Locus of Control (T-LOC), and Health Belief Model (HBM), were distributed to students at Ton Thang University and University of Architecture, Ho Chi Minh City. SEM was used to explain helmet use behaviour. The results indicate that TPB, T-LOC and HBM could explain the variance in helmet use behaviour. However, TPB can explain behaviour (helmet use intention) better than T-LOC and HBM. The outcome of this study is useful for the agencies responsible to improve motorcycle safety.

Methodologies for Blunt Trauma Assessment in Military Helmets

Science.gov (United States)

2010-09-13

Assessment; Monorail Drop Tower 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU 18. NUMBER OF PAGES 10 19a. NAME OF RESPONSIBLE...Laboratory Test Procedure for Motorcycle Helmets (TP-218-06) [8]. TP-218-06 specifies a guided monorail drop and provides requirements for how helmets...a hemispherical anvil. The monorail restricts movement to control the impact location, and acceleration is measured using a uniaxial accelerometer

Analysing Self Interference Cancellation in Full Duplex Radios

DEFF Research Database (Denmark)

Mahmood, Nurul Huda; Shafique Ansari, Imran; Berardinelli, Gilberto

2016-01-01

Full duplex communication promises a theoretical $100\\%$ throughput gain by doubling the number of simultaneous transmissions. Such compelling gains are conditioned on perfect cancellation of the self interference power resulting from simultaneous transmission and reception. Generally, self...... interference power is modelled as a noise-like constant level interference floor. However, experimental validations have shown that the self interference power is in practice a random variable depending on a number of factors such as the surrounding wireless environment and the degree of interference...... cancellation. In this study, we derive an analytical model for the residual self interference power, and demonstrate various applications of the derived model in analysing the performance of a Full Duplex radio. In general, full duplex communication is found to provide only modest throughput gains over half...

GPK helmets protecting from gas and dusts

Energy Technology Data Exchange (ETDEWEB)

Il' inskii, Eh.G.; Kogan, Yu.A.; Mazanenko, V.P.

1983-08-01

The GPK protective helmet with an integrated respirator system protecting a miner's respiratory system and eyes from gases and dusts is described. The system uses compressed air from the mine compressed air system. Air is supplied to the respirator by an elastic rubber pipe to 30 m long. The air cools the miner's head under the helmet and passes between a protective shield and the miner's face protecting eyes and the respiratory system. Air supply ranges from 100 to 150 l/min. The air supplied to the respirator is cleaned by a filter. The GPK system weighs 1.2 kg. The system has been tested under laboratory conditions and in two coal mines under operational conditions at longwall faces and during mine drivage. Tests showed that the GPK guarantees efficient cooling and protection from dust. Design of the GPK helmet with a respirator is shown in two schemes. Technical specifications of the system are given.

Intelligent audio analysis

CERN Document Server

Schuller, Björn W

2013-01-01

This book provides the reader with the knowledge necessary for comprehension of the field of Intelligent Audio Analysis. It firstly introduces standard methods and discusses the typical Intelligent Audio Analysis chain going from audio data to audio features to audio recognition.  Further, an introduction to audio source separation, and enhancement and robustness are given. After the introductory parts, the book shows several applications for the three types of audio: speech, music, and general sound. Each task is shortly introduced, followed by a description of the specific data and methods applied, experiments and results, and a conclusion for this specific task. The books provides benchmark results and standardized test-beds for a broader range of audio analysis tasks. The main focus thereby lies on the parallel advancement of realism in audio analysis, as too often today’s results are overly optimistic owing to idealized testing conditions, and it serves to stimulate synergies arising from transfer of ...

Modular liquid-cooled helmet liner for thermal comfort

Science.gov (United States)

Williams, B. A.; Shitzer, A.

1974-01-01

A modular liquid-cooled helmet liner made of eight form-fitting neoprene patches was constructed. The liner was integrated into the sweatband of an Army SPH-4 helicopter aircrew helmet. This assembly was tested on four subjects seated in a hot (47 C), humid (40%) environment. Results indicate a marked reduction in the rate of increase of physiological body functions. Rectal temperature, weight loss, heart rate, and strain indices are all reduced to approximately 50% of uncooled levels. The cooling liner removed from 10% to 30% of total metabolic heat produced. This study also demonstrated the technical feasilibity of using a cooling liner in conjunction with a standard hard helmet. Potential applications of the cooling liner in thermally stressful environments are numerous, notably for helicopter and other aircrews.

Wideband Balun-LNA with Simultaneous Output Balancing, Noise-Canceling and Distortion-Canceling

NARCIS (Netherlands)

Blaakmeer, S.C.; Klumperink, Eric A.M.; Leenaerts, D.M.W.; Nauta, Bram

2008-01-01

An inductorless low-noise amplifier (LNA) with active balun is proposed for multi-standard radio applications between 100 MHz and 6 GHz. It exploits a combination of a common-gate (CGH) stage and an admittance-scaled common-source (CS) stage with replica biasing to maximize balanced operation, while

Partial Cancellation

Indian Academy of Sciences (India)

First page Back Continue Last page Overview Graphics. Partial Cancellation. Full Cancellation is desirable. But complexity requirements are enormous. 4000 tones, 100 Users billions of flops !!! Main Idea: Challenge: To determine which cross-talker to cancel on what “tone” for a given victim. Constraint: Total complexity is ...

A cross-sectional observational study of helmet use among motorcyclists in Wa, Ghana.

Science.gov (United States)

Akaateba, Millicent Awialie; Amoh-Gyimah, Richard; Yakubu, Ibrahim

2014-03-01

Motorcyclists' injuries and fatalities are a major public health concern in many developing countries including Ghana. This study therefore aimed to investigate the prevalence of helmet use among motorcyclists in Wa, Ghana. The method used involved a cross-sectional roadside observation at 12 randomly selected sites within and outside the CBD of Wa. A total of 14,467 motorcyclists made up of 11,360 riders and 3107 pillion riders were observed during the study period. Most observed riders (86.5%) and pillion riders (61.7%) were males. The overall prevalence of helmet use among the observed motorcyclists was 36.9% (95% CI: 36.1-37.7). Helmet use for riders was 45.8% (95% CI: 44.8-46.7) whilst that for pillion riders was 3.7% (95 CI: 3.0-4.4). Based on logistic regression analysis, higher helmet wearing rates were found to be significantly associated with female gender, weekdays, morning periods and at locations within the CBD. Riders at locations outside the CBD were about 7 times less likely to wear a helmet than riders within the CBD (48.9% compared to 42.3%; χ(2)(1)=49.526; plegislation that mandates the use of helmets by both riders and pillion riders on all roads in Ghana, helmet use is generally low in Wa. This suggests that all stakeholders in road safety should jointly intensify education on helmet use and pursue rigorous enforcement on all road types especially at locations outside the CBD to improve helmet use in Wa. Copyright © 2013 Elsevier Ltd. All rights reserved.

Neck muscle strain when wearing helmet and NVG during acceleration on a trampoline.

Science.gov (United States)

Sovelius, Roope; Oksa, Juha; Rintala, Harri; Huhtala, Heini; Siitonen, Simo

2008-02-01

The helmet-mounted equipment worn by military pilots increases the weight of the helmet system and shifts its center of gravity, increasing the loads on neck structures, especially during acceleration. The aim of this study was to determine neck muscle strain with different head-loads during trampoline-induced G loads (0 to +4 G). Under three conditions [no helmet, helmet, helmet with night vision goggles (NVG)], 14 subjects performed trampoline exercises including basic, hand-and-knee, and back bouncing. EMG activity was measured for the sternocleidomastoid (SCM), cervical erector spinae (CES), trapezoid (TRA), and thoracic erector spinae (TES) muscles. Muscle strain was determined as a percentage of maximal voluntary contraction (%MVC). For the three exercises combined, the following significant changes were found: compared to control, the helmet increased muscle strain by 18%, 28%, and 18% in the SCM, CES, and TRA, respectively; NVG produced a further increase of 11% in the SCM and 6% in the CES. During back bouncing, the helmet increased muscle strain by 14% in the SCM and 19% in the CES, and NVG further increased this strain by 14% in the SCM. Hand-and-knee bouncing loaded extensors: the helmet caused increases of 46% in the CES and 29% in the TES, while NVG produced a further 13% increase in CES activation. Helmet weight alone had a large effect on muscular workload. The additional frontal weight of the NVG caused a further increase in the activity of cervical muscles that were already subjected to high strain.

Noise pollution effect in flour factory on workers' hearing in Lamerd City.

Science.gov (United States)

Mohammadizadeh, M; Ahmadi, S H; Sekhavati, E; Ahani-Jegar, K

2015-01-01

Introduction: Noise pollution is one of the most important problems in industry that has an effect on the auditory system and other physiological parameters, as well as persons in noise exposure situations. While noise-induced hearing loss is preventable, once acquired, hearing loss is permanent and irreversible. Methodology: In the current study, noise in various sections of Flour Company in Lamerd estimated via the audio recorder, which revealed that the operators' expression remained larger than the state criterion; hence, the perception experiment (audio recorder) was performed on the operators and its outcomes were examined via utilizing SPSS 16 of version. Findings: Overall, Pearson relationship r = 0.453 discovered among job reports and the performance decline between all operators by significant stage p≤0.05. Moreover, T-test applied to examine noise impact on operators included in boisterous rooms (mean more than 85 dB) also average=26. 71 and regular deviation=11.72 got (p≤0.05) that was greater than 25db (as the standard hearing threshold). Conclusion: The outcomes of audio measuring and T-test revealed that the noise corruption has an impact on the hearing of bodies operating in noisy rooms.

pyAudioAnalysis: An Open-Source Python Library for Audio Signal Analysis.

Science.gov (United States)

Giannakopoulos, Theodoros

2015-01-01

Audio information plays a rather important role in the increasing digital content that is available today, resulting in a need for methodologies that automatically analyze such content: audio event recognition for home automations and surveillance systems, speech recognition, music information retrieval, multimodal analysis (e.g. audio-visual analysis of online videos for content-based recommendation), etc. This paper presents pyAudioAnalysis, an open-source Python library that provides a wide range of audio analysis procedures including: feature extraction, classification of audio signals, supervised and unsupervised segmentation and content visualization. pyAudioAnalysis is licensed under the Apache License and is available at GitHub (https://github.com/tyiannak/pyAudioAnalysis/). Here we present the theoretical background behind the wide range of the implemented methodologies, along with evaluation metrics for some of the methods. pyAudioAnalysis has been already used in several audio analysis research applications: smart-home functionalities through audio event detection, speech emotion recognition, depression classification based on audio-visual features, music segmentation, multimodal content-based movie recommendation and health applications (e.g. monitoring eating habits). The feedback provided from all these particular audio applications has led to practical enhancement of the library.

Injuries of the head from backface deformation of ballistic protective helmets under ballistic impact.

Science.gov (United States)

Rafaels, Karin A; Cutcliffe, Hattie C; Salzar, Robert S; Davis, Martin; Boggess, Brian; Bush, Bryan; Harris, Robert; Rountree, Mark Steve; Sanderson, Ellory; Campman, Steven; Koch, Spencer; Dale Bass, Cameron R

2015-01-01

Modern ballistic helmets defeat penetrating bullets by energy transfer from the projectile to the helmet, producing helmet deformation. This deformation may cause severe injuries without completely perforating the helmet, termed "behind armor blunt trauma" (BABT). As helmets become lighter, the likelihood of larger helmet backface deformation under ballistic impact increases. To characterize the potential for BABT, seven postmortem human head/neck specimens wearing a ballistic protective helmet were exposed to nonperforating impact, using a 9 mm, full metal jacket, 124 grain bullet with velocities of 400-460 m/s. An increasing trend of injury severity was observed, ranging from simple linear fractures to combinations of linear and depressed fractures. Overall, the ability to identify skull fractures resulting from BABT can be used in forensic investigations. Our results demonstrate a high risk of skull fracture due to BABT and necessitate the prevention of BABT as a design factor in future generations of protective gear. © 2014 American Academy of Forensic Sciences.

Noise measurements on proximity effect bridges

International Nuclear Information System (INIS)

Decker, S.K.; Mercereau, J.E.

1975-01-01

Audio frequency noise density measurements were performed on weakly superconducting proximity effect bridges on using a cooled transformer and room temperature low noise preamplifier. The noise temperature of the measuring system is approximately 4 0 K for a 0.9 Ω resistor. Noise density was measured as a function of bias current and temperature for the bridges. Excess noise above that expected from Johnson noise for a resistor equal to the dynamic resistance of the bridges was observed in the region near the critical current of the device. At high currents compared to the critical current, the noise density closely approaches that given by Johnson noise

Intelligent coil drum with electromagnetic force cancellation for MRI equipment

International Nuclear Information System (INIS)

Qiu, Jinhao; Tani, Junji; Ohtomo, Kikuo

1995-01-01

High-level noise induced in MRI equipment has been a main obstacle for their wide application in medical diagnosis. The noise is caused by the vibration of the cylindrical shell used to support the gradient magnetic field coils in MRI. In this study, a reduced-size model of the coil drum is constructed using polymer films and piezoelectric films. The piezoelectric films are divided into several patches and two patches of them are used as integrated bending actuators in the control of the shell vibration so that no external actuators are needed. The disturbance cancellation method is used since the shell is excited by predetermined forces. The relationships between the size, position and output magnitude of the actuators and control effect are also discussed. Experiment and simulation were carried out for the cases where the shell was excited at resonance frequencies of three main modes. The results show that the disturbance cancellation method in combination with the piezoelectric film actuators can successfully suppress the forced vibration of the shell and that the minimum amplitude of controlled vibration varies with the resonance mode. (author)

A New Probe Noise Approach For Acoustic Feedback Cancellation In Hearing Aids

DEFF Research Database (Denmark)

Guo, Meng; Jensen, Søren Holdt; Jensen, Jesper

Acoustic feedback is a big challenge in hearing aids. If not appropriately treated, the feedback limits the maximum possible amplification and may lead to significant sound distortions. In a state-of-the-art hearing aid, an acoustic feedback cancellation (AFC) system is used to compensate...

Helmets or not? Use science correctly.

Science.gov (United States)

Trégouët, Paul

2015-08-01

In a recent article, Hooper and Spicer make several arguments against legislation that would mandate the use of bicycle helmets. While they present reasonable objections to the utilitarian as well as the justice defence of such legislation, their review of the empirical evidence contains inaccuracies, omissions and a bias in the selection of empirical data. While there are legitimate reasons to argue against mandating helmet legislation, these arguments should still be based on clinically and scientifically sound evidence. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Audio segmentation of broadcast news in the Albayzin-2010 evaluation: overview, results, and discussion

Directory of Open Access Journals (Sweden)

Butko Taras

2011-01-01

Full Text Available Abstract Recently, audio segmentation has attracted research interest because of its usefulness in several applications like audio indexing and retrieval, subtitling, monitoring of acoustic scenes, etc. Moreover, a previous audio segmentation stage may be useful to improve the robustness of speech technologies like automatic speech recognition and speaker diarization. In this article, we present the evaluation of broadcast news audio segmentation systems carried out in the context of the Albayzín-2010 evaluation campaign. That evaluation consisted of segmenting audio from the 3/24 Catalan TV channel into five acoustic classes: music, speech, speech over music, speech over noise, and the other. The evaluation results displayed the difficulty of this segmentation task. In this article, after presenting the database and metric, as well as the feature extraction methods and segmentation techniques used by the submitted systems, the experimental results are analyzed and compared, with the aim of gaining an insight into the proposed solutions, and looking for directions which are promising.

The influence of ski helmets on sound perception and sound localisation on the ski slope

Directory of Open Access Journals (Sweden)

Lana Ružić

2015-04-01

Full Text Available Objectives: The aim of the study was to investigate whether a ski helmet interferes with the sound localization and the time of sound perception in the frontal plane. Material and Methods: Twenty-three participants (age 30.7±10.2 were tested on the slope in 2 conditions, with and without wearing the ski helmet, by 6 different spatially distributed sound stimuli per each condition. Each of the subjects had to react when hearing the sound as soon as possible and to signalize the correct side of the sound arrival. Results: The results showed a significant difference in the ability to localize the specific ski sounds; 72.5±15.6% of correct answers without a helmet vs. 61.3±16.2% with a helmet (p < 0.01. However, the performance on this test did not depend on whether they were used to wearing a helmet (p = 0.89. In identifying the timing, at which the sound was firstly perceived, the results were also in favor of the subjects not wearing a helmet. The subjects reported hearing the ski sound clues at 73.4±5.56 m without a helmet vs. 60.29±6.34 m with a helmet (p < 0.001. In that case the results did depend on previously used helmets (p < 0.05, meaning that that regular usage of helmets might help to diminish the attenuation of the sound identification that occurs because of the helmets. Conclusions: Ski helmets might limit the ability of a skier to localize the direction of the sounds of danger and might interfere with the moment, in which the sound is firstly heard.

Achieving all-age helmet use compliance for snow sports: strategic use of education, legislation and enforcement.

Science.gov (United States)

Fenerty, Lynne; Heatley, Jennifer; Young, Julian; Thibault-Halman, Ginette; Kureshi, Nelofar; Bruce, Beth S; Walling, Simon; Clarke, David B

2016-06-01

Nova Scotia is the first jurisdiction in the world to mandate ski and snowboard helmet use for all ages at ski hills in the province. This study represents a longitudinal examination of the effects of social marketing, educational campaigns and the introduction of helmet legislation on all-age snow sport helmet use in Nova Scotia. A baseline observational study was conducted to establish the threshold of ski and snowboarding helmet use. Based on focus groups and interviews, a social marketing campaign was designed and implemented to address factors influencing helmet use. A prelegislation observational study assessed the effects of social marketing and educational promotion on helmet use. After all-age snow sport helmet legislation was enacted and enforced, a postlegislation observational study was conducted to determine helmet use prevalence. Baseline data revealed that 74% of skiers and snowboarders were using helmets, of which 80% were females and 70% were males. Helmet use was high in children (96%), but decreased with increasing age. Following educational and social marketing campaigns, overall helmet use increased to 90%. After helmet legislation was enacted, 100% compliance was observed at ski hills in Nova Scotia. Results from this study demonstrate that a multifaceted approach, including education, legislation and enforcement, was effective in achieving full helmet compliance among all ages of skiers and snowboarders. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Helmet-Induced Occipital Neuralgia in a Military Aviator.

Science.gov (United States)

Chalela, Julio A

2018-04-01

Headaches among military personnel are very common and headgear wear is a frequently identified culprit. Helmet wear may cause migrainous headaches, external compression headache, other primary cranial neuralgias, and occipital neuralgia. The clinical features and the response to treatment allow distinction between the different types of headaches. Headaches among aviators are particularly concerning as they may act as distractors while flying and the treatment options are often incompatible with flying status. A 24-yr-old door gunner presented with suboccipital pain associated with the wear of his helmet. He described the pain as a paroxysmal stabbing sensation coming in waves. The physical exam and history supported the diagnosis of primary occipital neuralgia. Systemic pharmacological options were discussed with the soldier, but rejected due to his need to remain in flying status. An occipital nerve block was performed with good clinical results, supporting the diagnosis of occipital neuralgia and allowing him to continue as mission qualified. Occipital neuralgia can be induced by helmet wear in military personnel. Occipital nerve block can be performed in the deployed setting, allowing the service member to remain mission capable and sparing him/her from systemic side effects.Chalela JA. Helmet-induced occipital neuralgia in a military aviator. Aerosp Med Hum Perform. 2018; 89(4):409-410.

The audio expert everything you need to know about audio

CERN Document Server

Winer, Ethan

2012-01-01

The Audio Expert is a comprehensive reference that covers all aspects of audio, with many practical, as well as theoretical, explanations. Providing in-depth descriptions of how audio really works, using common sense plain-English explanations and mechanical analogies with minimal math, the book is written for people who want to understand audio at the deepest, most technical level, without needing an engineering degree. It's presented in an easy-to-read, conversational tone, and includes more than 400 figures and photos augmenting the text.The Audio Expert takes th

Reduced Pain and Anxiety with Music and Noise-Canceling Headphones During Shockwave Lithotripsy.

Science.gov (United States)

Karalar, Mustafa; Keles, Ibrahim; Doğantekin, Engin; Kahveci, Orhan Kemal; Sarici, Hasmet

2016-06-01

We assessed the effects of music and noise-canceling headphones (NCHs) on perceived patient pain and anxiety from extracorporeal shockwave lithotripsy (SWL). Patients with renal calculi scheduled for SWL were prospectively enrolled. All 89 patients between the ages of 19 and 80 years were informed about this study and then randomized into three groups: Group 1 (controls), no headphones and music; Group 2, music with NCHs (patients listened to Turkish classical music with NCHs during SWL); and Group 3, music with non-NCHs (patients listened to Turkish classical music with non-NCHs during SWL). Hemodynamic and respiratory parameters were recorded before and just after the SWL session. All patient visual analog scale (VAS) and State-Trait Anxiety Inventory (STAI) scores were recorded just after the SWL procedure. There were significant differences in VAS scores among the groups (5.1, 3.6, and 4.5, respectively, p < 0.001), including between Groups 2 and 3 (p = 0.018). There were also significant differences in STAI-State anxiety scores among the groups (43.1, 33.5, and 38.9, respectively, p = 0.001), including between Groups 2 and 3 (p = 0.04). Music therapy during SWL reduced pain and anxiety. Music therapy with NCHs was more effective for pain and anxiety reduction. To reduce pain and anxiety, nonpharmacologic therapies such as music therapy with NCHs during SWL should be investigated further and used routinely.

Quiet comfort: noise, otherness, and the mobile production of personal space.

Science.gov (United States)

Hagood, Mack

2011-01-01

Marketing, news reports, and reviews of Bose QuietComfort noise-canceling headphones position them as essential gear for the mobile rational actor of the neoliberal market—the business traveler. This article concerns noise-canceling headphones’ utility as soundscaping devices, which render a sense of personal space by mediating sound. The airplane and airport are paradoxical spaces in which the pursuit of freedom impedes its own enjoyment. Rather than fight the discomforts of air travel as a systemic problem, travelers use the tactic of soundscaping to suppress the perceived presence of others. Attention to soundscaping enables the scholar to explore relationships between media, space, freedom, otherness, and selfhood in an era characterized by neoliberalism and increased mobility. Air travel is a moment in which people with diverse backgrounds, beliefs, and bodies crowd together in unusually close proximity. Noise is the sound of individualism and difference in conflict. Noise is othered sound, and like any type of othering, the perception of noise is socially constructed and situated in hierarchies of race, class, age, and gender. The normative QuietComfort user in media representations is white, male, rational, monied, and mobile; women, children, and “chatty” passengers are cast as noisemakers. Moreover, in putting on noise-canceling headphones, diverse selves put on the historically Western subjectivity that has been built into their technology, one that suppresses the noise of difference in favor of the smooth circulation of people, information, and commodities.

Electrocardiogram de-noising based on forward wavelet transform ...

Indian Academy of Sciences (India)

Ratio (SNR) and Mean Square Error (MSE) computations showed that our proposed ... This technique permits to cancel noises and retain the informa- tion of the ... Wavelet analysis is used for transforming the signal under investigation into joined temporal and ... introduced the BWT in our proposed ECG de-noising system.

Dynamic Response and Residual Helmet Liner Crush Using Cadaver Heads and Standard Headforms.

Science.gov (United States)

Bonin, S J; Luck, J F; Bass, C R; Gardiner, J C; Onar-Thomas, A; Asfour, S S; Siegmund, G P

2017-03-01

Biomechanical headforms are used for helmet certification testing and reconstructing helmeted head impacts; however, their biofidelity and direct applicability to human head and helmet responses remain unclear. Dynamic responses of cadaver heads and three headforms and residual foam liner deformations were compared during motorcycle helmet impacts. Instrumented, helmeted heads/headforms were dropped onto the forehead region against an instrumented flat anvil at 75, 150, and 195 J. Helmets were CT scanned to quantify maximum liner crush depth and crush volume. General linear models were used to quantify the effect of head type and impact energy on linear acceleration, head injury criterion (HIC), force, maximum liner crush depth, and liner crush volume and regression models were used to quantify the relationship between acceleration and both maximum crush depth and crush volume. The cadaver heads generated larger peak accelerations than all three headforms, larger HICs than the International Organization for Standardization (ISO), larger forces than the Hybrid III and ISO, larger maximum crush depth than the ISO, and larger crush volumes than the DOT. These significant differences between the cadaver heads and headforms need to be accounted for when attempting to estimate an impact exposure using a helmet's residual crush depth or volume.

[Prevalence of helmet use in children and adolescents in Germany and preventable bicycle-related head injuries].

Science.gov (United States)

Gutsche, J; Hintzpeter, B; Neuhauser, H; Schlaud, M

2011-08-01

Head injuries are the main cause of death in bicycle-related accidents among children and adolescents. According to a Cochrane Review, the risk of head injury (OR 0.31; 95% CI 0.26-0.37) or brain injury (OR 0.31; 95% CI 0.23-0.42) decreases by 69% if a helmet is worn. This study presents the prevalence of helmet use in cycling children and adolescents in Germany and the proportion of head injuries that could be prevented by wearing helmets. The potential effects of increased helmet wearing rates on the population attributable risk percentage for head injuries (PAR%) are demonstrated. The prevalence of helmet use in children aged 3-17 years was analysed using data from the German Health Interview and Examination Survey for Children and Adolescents (KiGGS). The percentage of head injuries preventable by helmet use in this group is estimated by calculating PAR%. Prevalence rates of helmet use and odds ratios from a Cochrane Review about the effectiveness of bicycle helmets for the prevention of head injuries were used for analysis. The potential effect of increased helmet use is shown in 3 scenarios by means of differences of PAR% values in the most relevant age groups. The older the children, the less likely they are to wear a helmet: 89.5% (95% CI 88.0%-90.8%) of the 3- to 6-year-old children wear a helmet when cycling but only 11.0% (95% CI 9.3%-12.9%) of 14- to 17-year-old adolescents do. In the youngest group (3-6 years) 19% of bicycle-related head injuries are attributable to the non-use of helmets, but this proportion rises to 67% in the oldest group (14-17 years). The PAR% of head injuries associated with not wearing a helmet may be reduced by more than a third by increasing the helmet wearing rate to 67% (2 out of 3) among adolescents, and may be reduced to half if 75% of adolescents wore a helmet. Particularly older children and adolescents hardly use bicycle helmets, hence the rate of preventable head injury is high. Efforts towards increasing helmet use

Preventive Effects of Safety Helmets on Traumatic Brain Injury after Work-Related Falls

Directory of Open Access Journals (Sweden)

Sang Chul Kim

2016-10-01

Full Text Available Introduction: Work-related traumatic brain injury (TBI caused by falls is a catastrophic event that leads to disabilities and high socio-medical costs. This study aimed to measure the magnitude of the preventive effect of safety helmets on clinical outcomes and to compare the effect across different heights of fall. Methods: We collected a nationwide, prospective database of work-related injury patients who visited the 10 emergency departments between July 2010 and October 2012. All of the adult patients who experienced work-related fall injuries were eligible, excluding cases with unknown safety helmet use and height of fall. Primary and secondary endpoints were intracranial injury and in-hospital mortality. We calculated adjusted odds ratios (AORs of safety helmet use and height of fall for study outcomes, and adjusted for any potential confounders. Results: A total of 1298 patients who suffered from work-related fall injuries were enrolled. The industrial or construction area was the most common place of fall injury occurrence, and 45.0% were wearing safety helmets at the time of fall injuries. The safety helmet group was less likely to have intracranial injury comparing with the no safety helmet group (the adjusted odds ratios (ORs (95% confidence interval (CI: 0.42 (0.24–0.73, however, there was no statistical difference of in-hospital mortality between two groups (the adjusted ORs (95% CI: 0.83 (0.34–2.03. In the interaction analysis, preventive effects of safety helmet on intracranial injury were significant within 4 m height of fall. Conclusions: A safety helmet is associated with prevention of intracranial injury resulting from work-related fall and the effect is preserved within 4 m height of fall. Therefore, wearing a safety helmet can be an intervention for protecting fall-related intracranial injury in the workplace.

A Thermal Test System for Helmet Cooling Studies

Directory of Open Access Journals (Sweden)

Shaun Fitzgerald

2018-02-01

Full Text Available One of the primary causes of discomfort to both irregular and elite cyclists is heat entrapment by a helmet resulting in overheating and excessive sweating of the head. To accurately assess the cooling effectiveness of bicycle helmets, a heated plastic thermal headform has been developed. The construction consists of a 3D-printed headform of low thermal conductivity with an internal layer of high thermal mass that is heated to a constant uniform temperature by an electrical heating element. Testing is conducted in a wind tunnel where the heater power remains constant and the resulting surface temperature distribution is directly measured by 36 K-type thermocouples embedded within the surface of the head in conjunction with a thermal imaging camera. Using this new test system, four bicycle helmets were studied in order to measure their cooling abilities and to identify ‘hot spots’ where cooling performance is poor.

An Integrated Real-Time Beamforming and Postfiltering System for Nonstationary Noise Environments

Directory of Open Access Journals (Sweden)

Gannot Sharon

2003-01-01

Full Text Available We present a novel approach for real-time multichannel speech enhancement in environments of nonstationary noise and time-varying acoustical transfer functions (ATFs. The proposed system integrates adaptive beamforming, ATF identification, soft signal detection, and multichannel postfiltering. The noise canceller branch of the beamformer and the ATF identification are adaptively updated online, based on hypothesis test results. The noise canceller is updated only during stationary noise frames, and the ATF identification is carried out only when desired source components have been detected. The hypothesis testing is based on the nonstationarity of the signals and the transient power ratio between the beamformer primary output and its reference noise signals. Following the beamforming and the hypothesis testing, estimates for the signal presence probability and for the noise power spectral density are derived. Subsequently, an optimal spectral gain function that minimizes the mean square error of the log-spectral amplitude (LSA is applied. Experimental results demonstrate the usefulness of the proposed system in nonstationary noise environments.

Evaluation of a promotional strategy to increase bicycle helmet use by children.

Science.gov (United States)

Parkin, P C; Spence, L J; Hu, X; Kranz, K E; Shortt, L G; Wesson, D E

1993-04-01

Bicycle-related head injuries are an important cause of death and disability, despite the availability of helmets. The objective of this study was to evaluate the effectiveness of a school-based bicycle helmet promotion program in increasing helmet use by children while controlling for secular trends. Two high-income and two low-income schools in an urban Canadian community were selected to receive a bicycle helmet promotion intervention, with the remaining 18 schools serving as controls. Approximately 1800 observations of bicycling children were made at randomly selected observational sites 2 to 5 months after the intervention to assess changes in behavior. Helmet use at all observation sites tripled from 3.4% (1990, preintervention) to 16% (1991, postintervention). In the high-income intervention area, observed helmet use rose dramatically from 4% to 36% in contrast to the more modest increase in the high-income control area from 4% to 15%. In the low-income intervention area, there was a modest increase from 1% to 7%, but it did not differ from the increase in the low-income control area from 3% to 13%. The program was highly successful in children of high-income families but not in children of low-income families. Developing strategies for low-income families remains a priority.

Description of Anomalous Noise Events for Reliable Dynamic Traffic Noise Mapping in Real-Life Urban and Suburban Soundscapes

Directory of Open Access Journals (Sweden)

Francesc Alías

2017-02-01

Full Text Available Traffic noise is one of the main pollutants in urban and suburban areas. European authorities have driven several initiatives to study, prevent and reduce the effects of exposure of population to traffic. Recent technological advances have allowed the dynamic computation of noise levels by means of Wireless Acoustic Sensor Networks (WASN such as that developed within the European LIFE DYNAMAP project. Those WASN should be capable of detecting and discarding non-desired sound sources from road traffic noise, denoted as anomalous noise events (ANE, in order to generate reliable noise level maps. Due to the local, occasional and diverse nature of ANE, some works have opted to artificially build ANE databases at the cost of misrepresentation. This work presents the production and analysis of a real-life environmental audio database in two urban and suburban areas specifically conceived for anomalous noise events’ collection. A total of 9 h 8 min of labelled audio data is obtained differentiating among road traffic noise, background city noise and ANE. After delimiting their boundaries manually, the acoustic salience of the ANE samples is automatically computed as a contextual signal-to-noise ratio (SNR. The analysis of the real-life environmental database shows high diversity of ANEs in terms of occurrences, durations and SNRs, as well as confirming both the expected differences between the urban and suburban soundscapes in terms of occurrences and SNRs, and the rare nature of ANE.

The evaluation of speed skating helmet performance through peak linear and rotational accelerations.

Science.gov (United States)

Karton, Clara; Rousseau, Philippe; Vassilyadi, Michael; Hoshizaki, Thomas Blaine

2014-01-01

Like many sports involving high speeds and body contact, head injuries are a concern for short track speed skating athletes and coaches. While the mandatory use of helmets has managed to nearly eliminate catastrophic head injuries such as skull fractures and cerebral haemorrhages, they may not be as effective at reducing the risk of a concussion. The purpose of this study was to evaluate the performance characteristics of speed skating helmets with respect to managing peak linear and peak rotational acceleration, and to compare their performance against other types of helmets commonly worn within the speed skating sport. Commercially available speed skating, bicycle and ice hockey helmets were evaluated using a three-impact condition test protocol at an impact velocity of 4 m/s. Two speed skating helmet models yielded mean peak linear accelerations at a low-estimated probability range for sustaining a concussion for all three impact conditions. Conversely, the resulting mean peak rotational acceleration values were all found close to the high end of a probability range for sustaining a concussion. A similar tendency was observed for the bicycle and ice hockey helmets under the same impact conditions. Speed skating helmets may not be as effective at managing rotational acceleration and therefore may not successfully protect the user against risks associated with concussion injuries.

Improved Noise Minimum Statistics Estimation Algorithm for Using in a Speech-Passing Noise-Rejecting Headset

Directory of Open Access Journals (Sweden)

Seyedtabaee Saeed

2010-01-01

Full Text Available This paper deals with configuration of an algorithm to be used in a speech-passing angle grinder noise-canceling headset. Angle grinder noise is annoying and interrupts ordinary oral communication. Meaning that, low SNR noisy condition is ahead. Since variation in angle grinder working condition changes noise statistics, the noise will be nonstationary with possible jumps in its power. Studies are conducted for picking an appropriate algorithm. A modified version of the well-known spectral subtraction shows superior performance against alternate methods. Noise estimation is calculated through a multi-band fast adapting scheme. The algorithm is adapted very quickly to the non-stationary noise environment while inflecting minimum musical noise and speech distortion on the processed signal. Objective and subjective measures illustrating the performance of the proposed method are introduced.

Analysis of Individual Preferences for Tuning Noise-Reduction Algorithms

NARCIS (Netherlands)

Houben, Rolph; Dijkstra, Tjeerd M. H.; Dreschler, Wouter A.

2012-01-01

There is little research on user preference for different settings of noise reduction, especially for individual users. We therefore measured individual preferences for pairs of audio streams differing in the trade-off between noise reduction and speech distortion. A logistic probability model was

Face mask removal is safer than helmet removal for emergent airway access in American football.

Science.gov (United States)

Swartz, Erik E; Mihalik, Jason P; Beltz, Nora M; Day, Molly A; Decoster, Laura C

2014-06-01

In cases of possible cervical spine injury, medical professionals must be prepared to achieve rapid airway access while concurrently restricting cervical spine motion. Face mask removal (FMR), rather than helmet removal (HR), is recommended to achieve this. However, no studies have been reported that compare FMR directly with HR. The purpose of this study was to compare motion, time, and perceived difficulty in two commonly used American football helmets between FMR and HR techniques, and when helmet air bladders were deflated before HR compared with inflated scenarios. The study incorporated a repeated measures design and was performed in a controlled laboratory setting. Participants included 22 certified athletic trainers (15 men and seven women; mean age, 33.9±10.5 years; mean experience, 11.4±10.0 years; mean height, 172±9.4 cm; mean mass, 76.7±14.9 kg). All participants were free from upper extremity or central nervous system pathology for 6 months and provided informed consent. Dependent variables included head excursion in degrees (computed by subtracting the minimum position from the maximum position) in each of the three planes (sagittal, frontal, transverse), time to complete the required task, and ratings of perceived exertion. To address our study purposes, we used two-by-two repeated-measures analysis of variance (removal technique×helmet type, helmet type×deflation status) for each dependent variable. Independent variables consisted of removal technique (FMR and HR), helmet type (Riddell Revolution IQ [RIQ] and VSR4), and helmet deflation status (deflated [D], inflated, [I]). After familiarization, participants conducted two successful trials for each of six conditions in random order (RIQ-FMR, VSR4-FMR, RIQ-HR-D, VSR4-HR-D, RIQ-HR-I, and VSR4-HR-I). Face masks, helmets, and shoulder pads were removed from a live model wearing a properly fitted helmet and shoulder pads. The participant and an investigator stabilized the model's head. A six

Noise Reduction Efforts for Special Operations C-130 Aircraft Using Active Synchrophaser Control

National Research Council Canada - National Science Library

Hammond, Daryl; McKinley, Richard; Hale, Bill

1998-01-01

.... A more complicated approach uses an active noise cancellation (ANC) system, which offers improved performance that can augment passive methods to significantly reduce both internal and external aircraft noise...

Adaptive Nonlinear RF Cancellation for Improved Isolation in Simultaneous Transmit–Receive Systems

Science.gov (United States)

Kiayani, Adnan; Waheed, Muhammad Zeeshan; Anttila, Lauri; Abdelaziz, Mahmoud; Korpi, Dani; Syrjala, Ville; Kosunen, Marko; Stadius, Kari; Ryynanen, Jussi; Valkama, Mikko

2018-05-01

This paper proposes an active radio frequency (RF) cancellation solution to suppress the transmitter (TX) passband leakage signal in radio transceivers supporting simultaneous transmission and reception. The proposed technique is based on creating an opposite-phase baseband equivalent replica of the TX leakage signal in the transceiver digital front-end through adaptive nonlinear filtering of the known transmit data, to facilitate highly accurate cancellation under a nonlinear TX power amplifier (PA). The active RF cancellation is then accomplished by employing an auxiliary transmitter chain, to generate the actual RF cancellation signal, and combining it with the received signal at the receiver (RX) low noise amplifier (LNA) input. A closed-loop parameter learning approach, based on the decorrelation principle, is also developed to efficiently estimate the coefficients of the nonlinear cancellation filter in the presence of a nonlinear TX PA with memory, finite passive isolation, and a nonlinear RX LNA. The performance of the proposed cancellation technique is evaluated through comprehensive RF measurements adopting commercial LTE-Advanced transceiver hardware components. The results show that the proposed technique can provide an additional suppression of up to 54 dB for the TX passband leakage signal at the RX LNA input, even at considerably high transmit power levels and with wide transmission bandwidths. Such novel cancellation solution can therefore substantially improve the TX-RX isolation, hence reducing the requirements on passive isolation and RF component linearity, as well as increasing the efficiency and flexibility of the RF spectrum use in the emerging 5G radio networks.

Combat Helmet-Headform Coupling Characterized from Blunt Impact Events

Science.gov (United States)

2011-11-01

Testing was completed on a monorail drop tower to analyze the effect of helmet/headform coupling on the blunt impact behavior of ACH helmets using FMVSS...designates its own methods and test equipment: a drop tower ( monorail or twin- wire), headform (DOT, ISO, NOCSAE), headform CG accelerometer (single or...the more anthropomorphic International Standard Organization (ISO) half headform. Testing was completed on a monorail drop tower to analyze the effect

Performance analysis of power-efficient adaptive interference cancelation in fading channels

KAUST Repository

Radaydeh, Redha Mahmoud Mesleh; Alouini, Mohamed-Slim

2010-01-01

This paper analyzes the performance of a -steering scheme for highly correlated receive antennas in the presence of statistically unordered co-channel interferers over multipath fading channels. An adaptive activation of receive antennas according to the interfering signals fading conditions is considered in the analysis. Analytical expressions for various system performance measures, including the outage probability, average error probability of different signaling schemes, and raw moments of the combined signal-to-interference-plus-noise ratio (SINR) are obtained in exact forms. Numerical and simulation results for the performance-complexity tradeoff of this scheme is presented and then compared with that of full-size arbitrary interference cancelation and no cancelation scenarios. ©2010 IEEE.

Performance analysis of power-efficient adaptive interference cancelation in fading channels

KAUST Repository

Radaydeh, Redha Mahmoud Mesleh

2010-12-01

This paper analyzes the performance of a -steering scheme for highly correlated receive antennas in the presence of statistically unordered co-channel interferers over multipath fading channels. An adaptive activation of receive antennas according to the interfering signals fading conditions is considered in the analysis. Analytical expressions for various system performance measures, including the outage probability, average error probability of different signaling schemes, and raw moments of the combined signal-to-interference-plus-noise ratio (SINR) are obtained in exact forms. Numerical and simulation results for the performance-complexity tradeoff of this scheme is presented and then compared with that of full-size arbitrary interference cancelation and no cancelation scenarios. ©2010 IEEE.

A single antenna interference cancellation and adaptive technique based on ALOE

Directory of Open Access Journals (Sweden)

Xu Han

2017-02-01

Full Text Available A new type of single antenna interference cancellation (SAIC algorithm based on ALOE filtering module is introduced for co-channel interference cancellation in GSM/GPRS/EDGE downlink without changing the link structure of traditional receiver.Meanwhile,an adjacent frequency adaptive detection based on power spectrum estimation method is introduced to solve adjacent frequency interference and complex interference.Compared with traditional energy noise estimation method,the new method has simpler structure,less complexity,and can effectively improve the adaptability for various scenarios.The simulation results show that it can raise the resistance to co-channel frequency interference and adjacent frequency interference in multimode chips with low complexity,which improves the quality of 2G voice communication.

Head position in the MEG helmet affects the sensitivity to anterior sources.

Science.gov (United States)

Marinkovic, K; Cox, B; Reid, K; Halgren, E

2004-11-30

Current MEG instruments derive the whole-head coverage by utilizing a helmet-shaped opening at the bottom of the dewar. These helmets, however, are quite a bit larger than most people's heads so subjects commonly lean against the back wall of the helmet in order to maintain a steady position. In such cases the anterior brain sources may be too distant to be picked up by the sensors reliably. Potential "invisibility" of the frontal and anterior temporal sources may be particularly troublesome for the studies of cognition and language, as they are subserved significantly by these areas. We examined the sensitivity of the distributed anatomically-constrained MEG (aMEG) approach to the head position ("front" vs. "back") secured within a helmet with custom-tailored bite-bars during a lexical decision task. The anterior head position indeed resulted in much greater sensitivity to language-related activity in frontal and anterior temporal locations. These results emphasize the need to adjust the head position in the helmet in order to maximize the "visibility" of the sources in the anterior brain regions in cognitive and language tasks.

Audio Conferencing Enhancements

OpenAIRE

VESTERINEN, LEENA

2006-01-01

Audio conferencing allows multiple people in distant locations to interact in a single voice call. Whilst it can be very useful service it also has several key disadvantages. This thesis study investigated the options for improving the user experience of the mobile teleconferencing applications. In particular, the use of 3D, spatial audio and visualinteractive functionality was investigated as the means of improving the intelligibility and audio perception during the audio...

Clinical review: Helmet and non-invasive mechanical ventilation in critically ill patients.

Science.gov (United States)

Esquinas Rodriguez, Antonio M; Papadakos, Peter J; Carron, Michele; Cosentini, Roberto; Chiumello, Davide

2013-04-25

Non-invasive mechanical ventilation (NIV) has proved to be an excellent technique in selected critically ill patients with different forms of acute respiratory failure. However, NIV can fail on account of the severity of the disease and technical problems, particularly at the interface. The helmet could be an alternative interface compared to face mask to improve NIV success. We performed a clinical review to investigate the main physiological and clinical studies assessing the efficacy and related issues of NIV delivered with a helmet. A computerized search strategy of MEDLINE/PubMed (January 2000 to May 2012) and EMBASE (January 2000 to May 2012) was conducted limiting the search to retrospective, prospective, nonrandomized and randomized trials. We analyzed 152 studies from which 33 were selected, 12 physiological and 21 clinical (879 patients). The physiological studies showed that NIV with helmet could predispose to CO₂ rebreathing and increase the patients' ventilator asynchrony. The main indications for NIV were acute cardiogenic pulmonary edema, hypoxemic acute respiratory failure (community-acquired pneumonia, postoperative and immunocompromised patients) and hypercapnic acute respiratory failure. In 9 of the 21 studies the helmet was compared to a face mask during either continous positive airway pressure or pressure support ventilation. In eight studies oxygenation was similar in the two groups, while the intubation rate was similar in four and lower in three studies for the helmet group compared to face mask group. The outcome was similar in six studies. The tolerance was better with the helmet in six of the studies. Although these data are limited, NIV delivered by helmet could be a safe alternative to the face mask in patients with acute respiratory failure.

A Discussion of the Issue of Football Helmet Removal in Suspected Cervical Spine Injuries

Science.gov (United States)

Segan, Ross D.; Cassidy, Christine; Bentkowski, Jamie

1993-01-01

In some areas, it is a commonly accepted emergency medical technician protocol to remove a helmet during the initial management of suspected cervical spine injures. After a comprehensive survey of relevant literature, four primary reasons why Emergency Medical Services professionals would desire to remove a helmet emerge. Sources suggest that the presence of a helmet might: 1) interfere with immobilization of the athlete; 2) interfere with the ability to visualize injuries; 3) cause hyperflexion of the cervical spine; and 4) prevent proper airway management during a cardiorespiratory emergency. Many available protocols are designed for the removal of closed chamber motorcycle helmets that do not have removable face masks. There are a great number of differing viewpoints regarding this issue. The varying viewpoints are results of the failure of many emergency medical technician management protocols to address the unique situation presented by a football helmet. We: 1) demonstrate that football helmet removal is potentially dangerous and unnecessary, 2) suggest that cardiorespiratory emergencies can be effectively managed without removing the helmet, and 3) provide sports medicine professional with information that may be used to establish a joint Emergency Medical Services/Sports Medicine emergency action plan. ImagesFig. 1.Fig 2.Fig 3.Fig 4.Fig 5.Fig 6. PMID:16558244

40° image intensifier tubes in an integrated helmet system

Science.gov (United States)

Schreyer, Herbert; Boehm, Hans-Dieter V.; Svedevall, B.

1993-12-01

EUROCOPTER has been under contract to the French and German ministries of defence for five years to develop the TIGER, a second generation anti-tank helicopter. A piloting thermal imager has been installed on a steerable platform in the helicopter nose in order to achieve the possibility of flying round the clock. In addition to this sensor, which is sensitive at a wavelength of 10 micrometers , the German side has proposed using an Integrated Helmet System in the PAH 2. This helmet, manufactured by GEC-Marconi Avionics, incorporates two cathode ray tubes (CRT) and two image intensifier tubes which allow the pilot to use an additional sensor in the visible and near infrared spectrum. The electronic part will be built by Teldix. EUROCOPTER DEUTSCHLAND has received the first demonstrator of this helmet for testing in the EUROCOPTER Visionics Laboratory. Later, the C-prototype will be integrated into a BK 117 helicopter (AVT Avionik Versuchstrager). This new helmet has a field of view of 40 degree(s), and exit pupil of 15 mm and improved possibilities of adjusting the optical part. Laboratory tests have been carried out to test important parameters like optical resolution under low light level conditions, field of view, eye relief or exit pupil. The CRT channels have been tested for resolution, distortion, vignetting and homogeneity. The requirements and the properties of the helmet, test procedures and the results of these tests are presented in the paper.

Signal processing method for Johnson noise thermometry

International Nuclear Information System (INIS)

Hwang, I. G.; Moon, B. S.; Kinser, Rpger

2003-01-01

The development of Johnson Noise Thermometry requires a high sensitive preamplifier circuit to pick up the temperature-related noise on the sensing element. However, the random noise generated in this amplification circuit causes a significant erroneous influence to the measurement. This paper describes signal processing mechanism of the Johnson Noise Thermometry system which is underway of development in collaboration between KAERI and ORNL. It adopts two identical amplifier channels and utilizes a digital signal processing technique to remove the independent noise of each channel. The CPSD(Cross Power Spectral Density) function is used to cancel the independent noise and the differentiation of narrow or single frequency peak from the CPSD data separates the common mode electromagnetic interference noise

Prevalence and determinants of non-standard motorcycle safety helmets amongst food delivery workers in Selangor and Kuala Lumpur.

Science.gov (United States)

Kulanthayan, S; See, Lai Git; Kaviyarasu, Y; Nor Afiah, M Z

2012-05-01

Almost half of the global traffic crashes involve vulnerable groups such as pedestrian, cyclists and two-wheeler users. The main objective of this study was to determine the factors that influence standard of the safety helmets used amongst food delivery workers by presence of Standard and Industrial Research Institute of Malaysia (SIRIM) certification label. A cross sectional study was conducted amongst 150 food delivery workers from fast food outlets in the vicinity of Selangor and Kuala Lumpur. During observation, safety helmets were classified as standard safety helmet in the presence of SIRIM label and non-standard in the absence of the label. They were approached for questionnaire participation once consent was obtained and were requested to exchange their safety helmet voluntarily with a new one after the interview. Data analysis was carried out using SPSS. Chi square and logistic regression analysis was applied to determine the significance and odds ratio of the variables studied, respectively (penetration test, age, education level, knowledge, crash history, types of safety helmet, marital status and years of riding experience) against the presence of SIRIM label. The response rate for this study was 85.2%. The prevalence of non-standard helmets use amongst fast food delivery workers was 55.3%. Safety helmets that failed the penetration test had higher odds of being non-standard helmets compared with safety helmets passing the test. Types of safety helmet indicated half-shell safety helmets had higher odds to be non-standard safety helmets compared to full-shell safety helmets. Riders with more years of riding experience were in high odds of wearing non-standard safety helmets compared to riders with less riding experience. Non-standard (non-SIRIM approved) helmets were more likely to be half-shell helmets, were more likely to fail the standards penetration test, and were more likely to be worn by older, more experienced riders. The implications of these

Doubling the spectrum of time-domain induced polarization: removal of non-linear self-potential drift, harmonic noise and spikes, tapered gating, and uncertainty estimation

DEFF Research Database (Denmark)

Olsson, Per-Ivar; Fiandaca, Gianluca; Larsen, Jakob Juul

, a logarithmic gate width distribution for optimizing IP data quality and an estimate of gating uncertainty. Additional steps include modelling and cancelling of non-linear background drift and harmonic noise and a technique for efficiently identifying and removing spikes. The cancelling of non-linear background...... drift is based on a Cole-Cole model which effectively handles current induced electrode polarization drift. The model-based cancelling of harmonic noise reconstructs the harmonic noise as a sum of harmonic signals with a common fundamental frequency. After segmentation of the signal and determining....... The processing steps is successfully applied on full field profile data sets. With the model-based cancelling of harmonic noise, the first usable IP gate is moved one decade closer to time zero. Furthermore, with a Cole-Cole background drift model the shape of the response at late times is accurately retrieved...

BICYCLE HELMET DESIGN AND THE VIRTUAL VALIDATION OF THE IMPACT, AERODYNAMICS AND PRODUCTION PROCESS

Directory of Open Access Journals (Sweden)

Bojan Boshevski

2017-12-01

Full Text Available This paper presents the development process of a bicycle helmet through individual research, creation, presentation and analysis of the results of the most important product development stages. The quality of the development and manufacturing process of the protective equipment for extreme sports is an imperative for a successful product and its flawless function. The design of the bicycle helmet is made following the rules of the design in order to create a well-founded and functional product. After creating design sketches, a virtual prototype was developed in "SolidWorks" using the required ergonomic dimensions. 3D printed model of the human head with adapted ergonomic dimensions and the designed bicycle helmet was developed in order to verify the applied ergonomic measures. The virtual model will be used as an input in the finite element analysis of the helmet impact test based on the EN1078 standard and the aerodynamic simulations executed in "SolidWorks Simulation and Flow Simulation", for verification of the impact and aerodynamic properties. Virtual testing of aerodynamic features and the ability of the bicycle helmet to allow ventilation of the user's head indicate that the helmet performs its function in the desired way. Also, the virtual prototype will be used for the production process simulation in "SolidWorks Plastics" in order to analyze the production of the bicycle helmet. The polycarbonate helmet outer shell is subject to a number of simulations for the sake of analyzing the production process in order to obtain the desired characteristics of the polycarbonate outer shell and to avoid the disadvantages that occur in the manufacturing process. The main goal of this paper is to develop a safety bicycle helmet with improved ergonomic, validation of impact, aerodynamic characteristics and production process in order to produce a high quality product for mass use.

Auditory and visual reaction time and peripheral field of vision in helmet users

Directory of Open Access Journals (Sweden)

Abbupillai Adhilakshmi

2016-12-01

Full Text Available Background: The incidence of fatal accidents are more in two wheeler drivers compared to four wheeler drivers. Head injury is of serious concern when recovery and prognosis of the patients are warranted, helmets are being used for safety purposes by moped, scooters and motorcycle drivers. Although, helmets are designed with cushioning effect to prevent head injuries but there are evidences of increase risk of neck injuries and reduced peripheral vision and hearing in helmet users. A complete full coverage helmets provide about less than 3 percent restrictions in horizontal peripheral visual field compared to rider without helmet. The standard company patented ergonomically designed helmets which does not affect the peripheral vision neither auditory reaction time. Objective: This pilot study aimed to evaluate the peripheral field of vision and auditory and visual reaction time in a hypertensive, diabetic and healthy male and female in order to have a better insight of protective characteristics of helmet in health and disease. Method: This pilot study carried out on age matched male of one healthy, one hypertensive and one diabetic and female subject of one healthy, one hypertensive and one diabetics. The field of vision was assessed by Lister’s perimeter whereas auditory and visual reaction time was recorded with response analyser. Result : Gender difference was not noted in peripheral field of vision but mild difference was found in auditory reaction time for high frequency and visual reaction time for both red and green colour in healthy control. But lateral and downward peripheral visual field was found reduced whereas auditory and visual reaction time was found increased in both hypertensive and diabetic subject in both sexes. Conclusion: Peripheral vision, auditory reaction time and visual reaction time in hypertensive and diabetics may lead to vulnerable accident. Helmet use has proven to reduce extent of injury in motorcyclist and

Do helmets worn for hurling fail to protect the ear? Identification of an emerging injury pattern.

LENUS (Irish Health Repository)

Martin-Smith, James D

2012-12-01

Hurling is an Irish national game of stick and ball known for its ferocity, played by 190 000 players. Facial injuries were common but have been significantly reduced by legislation enforcing compulsory helmet wearing. Current standard helmets worn by hurlers do not offer protection to the external ear. Here we describe an emerging pattern of ear injuries and demonstrate the risk of external ear injuries in hurlers complying with current helmet safety standards. A 6-month retrospective analysis was carried out of patients attending Cork University Hospital (CUH) with ear lacerations sustained while hurling. Patient notes were reviewed and helmet manufacturers were interviewed. Seven patients were identified, all of whom sustained complex through ear lacerations while wearing helmets complying with current safety standards. Current helmet design fails to protect the external ear placing it at an increased risk of injury, a potential solution is to include ear protection in the helmet design.

Reactor noise monitoring device

International Nuclear Information System (INIS)

Yamanaka, Hiroto.

1990-01-01

The present invention concerns a reactor noise monitoring device by detecting abnormal sounds in background noises. Vibration sounds detected by accelerometers are applied to a loose parts detector. The detector generates high alarm if there are sudden impact sounds in the background noises and applies output signals to an accumulation device. If there is slight impact sounds in the vicinity of any of the accelerometers, the accumulation device accumulates the abnormal sounds assumed to be generated from an identical site while synchronizing the waveforms for all of the channels. Then, the device outputs signals in which the background noises are cancelled, as detection signals. Therefore, S/N ratio can be improved and the abnormal sounds contained in the background noises can be detected, to thereby improve the accuracy for estimating the position where the abnormal sounds are generated. (I.S.)

Bikes, helmets, and public health: decision-making when goods collide.

Science.gov (United States)

Bateman-House, Alison

2014-06-01

How ought public officials address policy choices that entail trade-offs between desirable public health goods? Increasing cycling improves public health both by promoting physical activity and by decreasing vehicle use, thus reducing vehicular emissions. Proponents of bicycle helmets argue that, used properly, they protect individual cyclists; however, there is concern that mandating helmet use may result in a decrease in cycling. In 2012, New York City Mayor Michael Bloomberg opposed a bicycle helmet mandate, concerned that it would have a negative impact on the city's cycling rate, which he had sought to increase. The mayor did not explain his rationale, leaving constituents unsure why he opposed the proposal. This case study underscores the challenge of creating public policy in the context of competing public health goods.

The Theory of Planned Behavior and Helmet Use among College Students

Science.gov (United States)

Ross, Lisa Thomson; Ross, Thomas P.; Farber, Sarah; Davidson, Caroline; Trevino, Meredith; Hawkins, Ashley

2011-01-01

Objectives: To assess undergraduate helmet use attitudes and behaviors in accordance with the theory of planned behavior (TPB). We predicted helmet wearers and nonwearers would differ on our subscales. Methods: Participants (N = 414, 69% female, 84% white) completed a survey. Results: Principal component analysis and reliability analysis guided…

The experimental plan of displacement- and frequency-noise free laser interferometer

International Nuclear Information System (INIS)

Kokeyama, K; Sato, S; Kawamura, S; Nishizawa, A; Chen, Y; Pai, A; Somiya, K; Ward, R; Sugamoto, A

2008-01-01

We present the partial demonstration of displacement- and laser-noise free interferometer (DFI) and the next experimental plan to examine the complete configuration. A part of the full implementation of DFI has been demonstrated to confirm the cancellation of beamsplitter displacements. The displacements were suppressed by about two orders of magnitude. The aim of the next experiment is to operate the system and to confirm the cancellation of all displacement noises, while the gravitational wave (GW) signals survive. The optical displacements will be simulated by electro-optic modulators (EOM). To simulate the GW contribution to laser lights, we will use multiple EOMs

Comparison of Linear Prediction Models for Audio Signals

Directory of Open Access Journals (Sweden)

2009-03-01

Full Text Available While linear prediction (LP has become immensely popular in speech modeling, it does not seem to provide a good approach for modeling audio signals. This is somewhat surprising, since a tonal signal consisting of a number of sinusoids can be perfectly predicted based on an (all-pole LP model with a model order that is twice the number of sinusoids. We provide an explanation why this result cannot simply be extrapolated to LP of audio signals. If noise is taken into account in the tonal signal model, a low-order all-pole model appears to be only appropriate when the tonal components are uniformly distributed in the Nyquist interval. Based on this observation, different alternatives to the conventional LP model can be suggested. Either the model should be changed to a pole-zero, a high-order all-pole, or a pitch prediction model, or the conventional LP model should be preceded by an appropriate frequency transform, such as a frequency warping or downsampling. By comparing these alternative LP models to the conventional LP model in terms of frequency estimation accuracy, residual spectral flatness, and perceptual frequency resolution, we obtain several new and promising approaches to LP-based audio modeling.

A Novel Robust Audio Watermarking Algorithm by Modifying the Average Amplitude in Transform Domain

Directory of Open Access Journals (Sweden)

Qiuling Wu

2018-05-01

Full Text Available In order to improve the robustness and imperceptibility in practical application, a novel audio watermarking algorithm with strong robustness is proposed by exploring the multi-resolution characteristic of discrete wavelet transform (DWT and the energy compaction capability of discrete cosine transform (DCT. The human auditory system is insensitive to the minor changes in the frequency components of the audio signal, so the watermarks can be embedded by slightly modifying the frequency components of the audio signal. The audio fragments segmented from the cover audio signal are decomposed by DWT to obtain several groups of wavelet coefficients with different frequency bands, and then the fourth level detail coefficient is selected to be divided into the former packet and the latter packet, which are executed for DCT to get two sets of transform domain coefficients (TDC respectively. Finally, the average amplitudes of the two sets of TDC are modified to embed the binary image watermark according to the special embedding rule. The watermark extraction is blind without the carrier audio signal. Experimental results confirm that the proposed algorithm has good imperceptibility, large payload capacity and strong robustness when resisting against various attacks such as MP3 compression, low-pass filtering, re-sampling, re-quantization, amplitude scaling, echo addition and noise corruption.

Offsetting or Enhancing Behavior: An Empirical Analysis of Motorcycle Helmet Safety Legislation.

Science.gov (United States)

Lee, Jonathan M

2015-10-01

This study uses state-level panel data from a 33-year period to test the hypotheses of offsetting and enhancing behavior with regards to motorcycle helmet legislation. Results presented in this article find no evidence of offsetting behavior and are consistent with the presence of enhancing behavior. State motorcycle helmet laws are estimated to reduce motorcycle crashes by 18.4% to 31.9%. In the absence of any behavioral adaptations among motorcyclists mandatory helmet laws are not expected to have any significant impact on motorcycle crash rates. The estimated motorcycle crash reductions do not appear to be driven by omitted variable bias or nonclassical measurement error in reported crashes. Overall, the results strongly suggest that mandatory helmet laws yield significant changes in motorcycle mobility in the form of reduced risk taking and/or decreased utilization. © 2015 Society for Risk Analysis.

Comparative Outcomes of Traumatic Brain Injury from Biking Accidents With or Without Helmet Use.

Science.gov (United States)

Dagher, Jehane H; Costa, Camille; Lamoureux, Julie; de Guise, Elaine; Feyz, Mitra

2016-01-01

To determine if health outcomes and demographics differ according to helmet status between persons with cycling-related traumatic brain injuries (TBI). This is a retrospective study of 128 patients admitted to the Montreal General Hospital following a TBI that occurred while cycling from 2007-2011. Information was collected from the Quebec trauma registry and the coroner's office in cases of death from cycling accidents. The independent variables collected were socio-demographic, helmet status, clinical and neurological patient information. The dependent variables evaluated were length of stay (LOS), extended Glasgow outcome scale (GOS-E), injury severity scale (ISS), discharge destination and death. 25% of cyclists wore a helmet. The helmet group was older, more likely to be university educated, married and retired. Unemployment, longer intensive care unit (ICU) stay, severe intracranial bleeding and neurosurgical interventions were more common in the no helmet group. There was no significant association between the severity of the TBI, ISS scores, GOS-E or death and helmet wearing. The median age of the subjects who died was higher than those who survived. Cyclists without helmets were younger, less educated, single and unemployed. They had more severe TBIs on imaging, longer LOS in ICU and more neurosurgical interventions. Elderly cyclists admitted to the hospital appear to be at higher risk of dying in the event of a TBI.

Injuries and helmet use related to non-motorized wheeled activities among pediatric patients.

Science.gov (United States)

Lindsay, H; Brussoni, M

2014-07-01

Patients presenting to emergency departments (ED) for injuries resulting from recreational activities represent a unique source of information on important directions for injury prevention efforts. We describe the epidemiology of non-motorized wheeled activity-related injury in pediatric patients presenting to Canadian EDs as well as patients' helmet use. Data for the years 2004 to 2009 were abstracted from the Canadian Hospitals Injury Reporting and Prevention Program (CHIRPP), a national ED injury surveillance program in fifteen hospitals. Most of the 28 618 children aged 1 to 16 years injured during non-motorized wheeled activities were injured while cycling, followed by skateboarding. Most injuries occurred among boys. Children injured on scooters tended to be younger whereas skateboarders were the oldest. On average, the number of all injuries decreased by 6% over the time period. Falls were the most common mechanism of injury; 8.3% of patients had head injuries, which were seen more often among cyclists than other wheeled-activity users. Helmet use was greatest among cyclists (62.2%) and lowest among skateboarders (32.9%). Injured patients presenting to EDs in jurisdictions with legislation mandating helmet use had 2.12 greater odds of helmet use and 0.86 lesser odds of head injury compared with those presenting in jurisdictions without helmet laws. These results provide further evidence that legislation mandating helmet use may be an effective way of reducing injury among all wheeled-activity users. The small number of patients who presented with helmet use and protective gear (59.4% overall) suggests that this remains an area for intervention.

Robustness against parametric noise of nonideal holonomic gates

International Nuclear Information System (INIS)

Lupo, Cosmo; Aniello, Paolo; Napolitano, Mario; Florio, Giuseppe

2007-01-01

Holonomic gates for quantum computation are commonly considered to be robust against certain kinds of parametric noise, the cause of this robustness being the geometric character of the transformation achieved in the adiabatic limit. On the other hand, the effects of decoherence are expected to become more and more relevant when the adiabatic limit is approached. Starting from the system described by Florio et al. [Phys. Rev. A 73, 022327 (2006)], here we discuss the behavior of nonideal holonomic gates at finite operational time, i.e., long before the adiabatic limit is reached. We have considered several models of parametric noise and studied the robustness of finite-time gates. The results obtained suggest that the finite-time gates present some effects of cancellation of the perturbations introduced by the noise which mimic the geometrical cancellation effect of standard holonomic gates. Nevertheless, a careful analysis of the results leads to the conclusion that these effects are related to a dynamical instead of a geometrical feature

Robustness against parametric noise of nonideal holonomic gates

Science.gov (United States)

Lupo, Cosmo; Aniello, Paolo; Napolitano, Mario; Florio, Giuseppe

2007-07-01

Holonomic gates for quantum computation are commonly considered to be robust against certain kinds of parametric noise, the cause of this robustness being the geometric character of the transformation achieved in the adiabatic limit. On the other hand, the effects of decoherence are expected to become more and more relevant when the adiabatic limit is approached. Starting from the system described by Florio [Phys. Rev. A 73, 022327 (2006)], here we discuss the behavior of nonideal holonomic gates at finite operational time, i.e., long before the adiabatic limit is reached. We have considered several models of parametric noise and studied the robustness of finite-time gates. The results obtained suggest that the finite-time gates present some effects of cancellation of the perturbations introduced by the noise which mimic the geometrical cancellation effect of standard holonomic gates. Nevertheless, a careful analysis of the results leads to the conclusion that these effects are related to a dynamical instead of a geometrical feature.

Improved Iterative Parallel Interference Cancellation Receiver for Future Wireless DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Andrea Bernacchioni

2005-04-01

Full Text Available We present a new turbo multiuser detector for turbo-coded direct sequence code division multiple access (DS-CDMA systems. The proposed detector is based on the utilization of a parallel interference cancellation (PIC and a bank of turbo decoders. The PIC is broken up in order to perform interference cancellation after each constituent decoder of the turbo decoding scheme. Moreover, in the paper we propose a new enhanced algorithm that provides a more accurate estimation of the signal-to-noise-plus-interference-ratio used in the tentative decision device and in the MAP decoding algorithm. The performance of the proposed receiver is evaluated by means of computer simulations for medium to very high system loads, in AWGN and multipath fading channel, and compared to recently proposed interference cancellation-based iterative MUD, by taking into account the number of iterations and the complexity involved. We will see that the proposed receiver outperforms the others especially for highly loaded systems.

Rates of motorcycle helmet use and reasons for non-use among adults and children in Luang Prabang, Lao People's Democratic Republic.

Science.gov (United States)

Fong, Michelle C; Measelle, Jeffrey R; Dwyer, Jessica L; Taylor, Yvonne K; Mobasser, Arian; Strong, Theresa M; Werner, Susanne; Ouansavanh, Siamphone; Mounmingkham, Amphone; Kasuavang, Mai; Sittiphone, Dalika; Phoumesy, Khamhak; Sysaythong, Keo; Khantysavath, Khauphan; Bounnaphone, Somchit; Vilaysom, Amphone; Touvachao, Sengchanh; Mounmeuangxam, Siviengxam; Souralay, Somchittana; Lianosay, Baoher; Lia, Thongher; Spector, Jonathan M

2015-09-28

Motorcycles make up 81 % of the total vehicle population and 74 % of road traffic deaths in Lao PDR. Helmets reduce the risk and severity of injuries resulting from motorcycle accidents by 72 %. Although Lao law mandates motorcycle helmet use among drivers and passengers, the prevalence of helmet use in Luang Prabang, Lao PDR is unknown. This project aimed to measure the prevalence of motorcycle helmet use among riders (i.e., drivers and passengers) in Luang Prabang. An observational survey in Luang Prabang was conducted in February 2015 to measure the prevalence of motorcycle helmet use among drivers and passengers. Additionally, non-helmet wearing riders were surveyed to identify the reasons for helmet non-use. Of 1632 motorcycle riders observed, only 16.2 % wore helmets. Approximately 29 % of adults wore helmets while less than 1 % of all children wore helmets. When surveyed about attitudes towards helmet use, the majority of adult drivers indicated that they did not like how adult helmets feel or made them look. Additionally, almost half of motorcyclists who did not own child helmets reported that their child was too young to wear a helmet. Our finding that children wear helmets at significantly lower rates compared to adults is consistent with findings from neighboring countries in Southeast Asia. Results of this study have implications for public health campaigns targeting helmet use, especially among children.

Factors Influencing Helmet Use, Head Injury, and Hospitalization Among Children Involved in Skateboarding and Snowboarding Accidents.

Science.gov (United States)

Sadeghian, Homa; Nguyen, Brian; Huynh, Nhan; Rouch, Joshua; Lee, Steven L; Bazargan-Hejazi, Shahrzad

2017-01-01

Up to 75% of skateboarders and snowboarders admitted to the hospital sustain head injuries. It is unclear why not all children and teenagers wear helmets while snowboarding and skateboarding given the protection they afford. To report on the prevalence of, and factors associated with, skateboarding and snowboarding in injured children and to explore factors that influence helmet use, head injury, and hospitalization in this sample. A cross-sectional study of skateboard- and snowboard-associated injuries from 2003 to 2012 among individuals younger than age 18 years using National Electronic Injury Surveillance System (NEISS) data from approximately 100 hospitals. Helmet use, head injury, and hospitalization. Of 1742 patients in the study, 852 (48.9%) and 890 (51.1%) were skateboarders and snowboarders, respectively. Overall, 907 (52.1%) did not use helmets, and 704 (40.4%) sustained head injuries. Multiple logistic regression analysis showed that age, race/ethnicity, location of boarding, and engaging in skateboarding influenced helmet use. Sex, race/ethnicity, helmet use, and skateboarding predicted head injury. Age, sex, skateboarding, and head injury predicted hospital admission. Statistically significant differences exist in helmet use, head injury, and hospitalization rates between skateboarders and snowboarders. Our findings suggest that injury prevention and outreach programs are needed to increase helmet use and reduce the risk of head injury and hospitalization in skateboarders and other at-risk groups. Further studies are needed to clarify the association between race/ethnicity and helmet use among skateboarders and snowboarders.

Maintaining neutral sagittal cervical alignment after football helmet removal during emergency spine injury management.

Science.gov (United States)

Decoster, Laura C; Burns, Matthew F; Swartz, Erik E; Murthi, Dinakar S; Hernandez, Adam E; Vailas, James C; Isham, Linda L

2012-04-15

Descriptive laboratory study. To determine whether the placement of padding beneath the occiput after helmet removal is an effective intervention to maintain neutral sagittal cervical spine alignment in a position comparable with the helmeted condition. Current on-field recommendations for managing football athletes with suspected cervical spine injuries call for face mask removal, rather than helmet removal, because the combination of helmet and shoulder pads has been shown to maintain neutral cervical alignment. Therefore, in cases when helmet removal is required, recommendations also call for shoulder pad removal. Because removal of equipment causes motion, any technique that postpones the need to remove the shoulder pads would reduce prehospital motion. Four lateral radiographs of 20 male participants were obtained (age = 23.6 ± 2.7 years). Radiographs of participants wearing shoulder pads and helmet were first obtained. The helmet was removed and radiographs of participants with occipital padding were obtained immediately and 20 minutes later and finally without occipital padding. Cobb angle measurements for C2-C6 vertebral segments were determined by an orthopedic spine surgeon blinded to the study's purpose. Intraobserver reliability was determined using intraclass coefficient analysis. Measurements were analyzed using a 1×4 repeated-measures analysis of variance and post hoc pairwise comparisons with Bonferroni correction. Intraobserver analysis showed excellent reliability (intraclass correlation = 1.0; 95% confidence interval [CI], 0.999-1.0). Repeated-measures analysis of variance detected significant differences (F(3,17) = 13.34; P football helmet in the field, occipital padding (along with full body/head immobilization techniques) may be used to limit cervical lordosis, allowing safe delay of shoulder pad removal.

Combined Effect of Random Transmit Power Control and Inter-Path Interference Cancellation on DS-CDMA Packet Mobile Communications

Science.gov (United States)

Kudoh, Eisuke; Ito, Haruki; Wang, Zhisen; Adachi, Fumiyuki

In mobile communication systems, high speed packet data services are demanded. In the high speed data transmission, throughput degrades severely due to severe inter-path interference (IPI). Recently, we proposed a random transmit power control (TPC) to increase the uplink throughput of DS-CDMA packet mobile communications. In this paper, we apply IPI cancellation in addition to the random TPC. We derive the numerical expression of the received signal-to-interference plus noise power ratio (SINR) and introduce IPI cancellation factor. We also derive the numerical expression of system throughput when IPI is cancelled ideally to compare with the Monte Carlo numerically evaluated system throughput. Then we evaluate, by Monte-Carlo numerical computation method, the combined effect of random TPC and IPI cancellation on the uplink throughput of DS-CDMA packet mobile communications.

Infra-sound cancellation and mitigation in wind turbines

Science.gov (United States)

Boretti, Albert; Ordys, Andrew; Al Zubaidy, Sarim

2018-03-01

The infra-sound spectra recorded inside homes located even several kilometres far from wind turbine installations is characterized by large pressure fluctuation in the low frequency range. There is a significant body of literature suggesting inaudible sounds at low frequency are sensed by humans and affect the wellbeing through different mechanisms. These mechanisms include amplitude modulation of heard sounds, stimulating subconscious pathways, causing endolymphatic hydrops, and possibly potentiating noise-induced hearing loss. We suggest the study of infra-sound active cancellation and mitigation to address the low frequency noise issues. Loudspeakers generate pressure wave components of same amplitude and frequency but opposite phase of the recorded infra sound. They also produce pressure wave components within the audible range reducing the perception of the infra-sound to minimize the sensing of the residual infra sound.

Experimental investigations on the cooling of a motorcycle helmet with phase change material (PCM

Directory of Open Access Journals (Sweden)

Fok S.C.

2011-01-01

Full Text Available The thermal comfort of motorcycle helmet during hot weather is important as it can affect the physiological and psychological condition of the rider. This paper examines the use of phase change material (PCM to cool a motorcycle helmet and presents the experimental investigations on the influences of the simulated solar radiation, wind speed, and heat generation rate on the cooling system. The result shows that the PCM-cooled helmet is able to prolong the thermal comfort period compared to a normal helmet. The findings also indicate that the heat generation from the head is the predominant factor that will affect the PCM melting time. Simulated solar radiation and ram-air due to vehicle motion under adiabatic condition can have very little influences on the PCM melting time. The results suggested that the helmet usage time would be influenced by the amount of heat generated from the head. Some major design considerations based on these findings have been included. Although this investigation focuses on the cooling of a motorcyclist helmet, the findings would also be useful for the development of PCM-cooling systems in other applications.

Neuromorphic Audio-Visual Sensor Fusion on a Sound-Localising Robot

Directory of Open Access Journals (Sweden)

Vincent Yue-Sek Chan

2012-02-01

Full Text Available This paper presents the first robotic system featuring audio-visual sensor fusion with neuromorphic sensors. We combine a pair of silicon cochleae and a silicon retina on a robotic platform to allow the robot to learn sound localisation through self-motion and visual feedback, using an adaptive ITD-based sound localisation algorithm. After training, the robot can localise sound sources (white or pink noise in a reverberant environment with an RMS error of 4 to 5 degrees in azimuth. In the second part of the paper, we investigate the source binding problem. An experiment is conducted to test the effectiveness of matching an audio event with a corresponding visual event based on their onset time. The results show that this technique can be quite effective, despite its simplicity.

Investigation of the reasons for not using helmet among motorcyclists in Kerman, Iran.

Science.gov (United States)

Maghsoudi, Aliasghar; Boostani, Dariush; Rafeiee, Manoochehr

2018-03-01

This study was carried out to investigate reasoning and interpretation of motorcyclists for not using helmet utilizing qualitative methodology of 'grounded theory'. The field of the study was Kerman, a cultural-historical city at the south-east of Iran. Participants were 21 young male motorcyclists. Two sampling strategies were used: maximum variation and snowball sampling. To collect data, in-depth, open-ended interviews were conducted. Data analysis yielded seven categories: fatalism; a barrier to social relationships; peer group pressure and negative labelling; messing up the appearance; disturbance in hearing and vision; barrier to normal breathing; and heaviness and superfluity of helmet. Based on the findings of the current study, it could be concluded that socio-cultural contexts, motorcyclists' worldview and partly helmet-related problems are of the main factors which affect motorcycling. Therefore, the studies, policy-makings, and intervening programmes to control injury and to promote safety among motorcyclists should be focused on socio-cultural barriers to helmet use in general and changing the motorcyclists' standpoints toward fatalism in particular. Helmet-related problems should be considered, too.

Aerodynamic study of time-trial helmets in cycling racing using CFD analysis.

Science.gov (United States)

Beaumont, F; Taiar, R; Polidori, G; Trenchard, H; Grappe, F

2018-01-23

The aerodynamic drag of three different time-trial cycling helmets was analyzed numerically for two different cyclist head positions. Computational Fluid Dynamics (CFD) methods were used to investigate the detailed airflow patterns around the cyclist for a constant velocity of 15 m/s without wind. The CFD simulations have focused on the aerodynamic drag effects in terms of wall shear stress maps and pressure coefficient distributions on the cyclist/helmet system. For a given head position, the helmet shape, by itself, obtained a weak effect on a cyclist's aerodynamic performance (CFD results have also shown that both helmet shape and head position significantly influence drag forces, pressure and wall shear stress distributions on the whole cyclist's body due to the change in the near-wake behavior and in location of corresponding separation and attachment areas around the cyclist. Copyright © 2017 Elsevier Ltd. All rights reserved.

Audio-Visual Speech in Noise Perception in Dyslexia

Science.gov (United States)

van Laarhoven, Thijs; Keetels, Mirjam; Schakel, Lemmy; Vroomen, Jean

2018-01-01

Individuals with developmental dyslexia (DD) may experience, besides reading problems, other speech-related processing deficits. Here, we examined the influence of visual articulatory information (lip-read speech) at various levels of background noise on auditory word recognition in children and adults with DD. We found that children with a…

Audio Twister

DEFF Research Database (Denmark)

Cermak, Daniel; Moreno Garcia, Rodrigo; Monastiridis, Stefanos

2015-01-01

Daniel Cermak-Sassenrath, Rodrigo Moreno Garcia, Stefanos Monastiridis. Audio Twister. Installation. P-Hack Copenhagen 2015, Copenhagen, DK, Apr 24, 2015.......Daniel Cermak-Sassenrath, Rodrigo Moreno Garcia, Stefanos Monastiridis. Audio Twister. Installation. P-Hack Copenhagen 2015, Copenhagen, DK, Apr 24, 2015....

Robust and Reversible Audio Watermarking by Modifying Statistical Features in Time Domain

Directory of Open Access Journals (Sweden)

Shijun Xiang

2017-01-01

Full Text Available Robust and reversible watermarking is a potential technique in many sensitive applications, such as lossless audio or medical image systems. This paper presents a novel robust reversible audio watermarking method by modifying the statistic features in time domain in the way that the histogram of these statistical values is shifted for data hiding. Firstly, the original audio is divided into nonoverlapped equal-sized frames. In each frame, the use of three samples as a group generates a prediction error and a statistical feature value is calculated as the sum of all the prediction errors in the frame. The watermark bits are embedded into the frames by shifting the histogram of the statistical features. The watermark is reversible and robust to common signal processing operations. Experimental results have shown that the proposed method not only is reversible but also achieves satisfactory robustness to MP3 compression of 64 kbps and additive Gaussian noise of 35 dB.

Back to basics audio

CERN Document Server

Nathan, Julian

1998-01-01

Back to Basics Audio is a thorough, yet approachable handbook on audio electronics theory and equipment. The first part of the book discusses electrical and audio principles. Those principles form a basis for understanding the operation of equipment and systems, covered in the second section. Finally, the author addresses planning and installation of a home audio system.Julian Nathan joined the audio service and manufacturing industry in 1954 and moved into motion picture engineering and production in 1960. He installed and operated recording theaters in Sydney, Austra

Astronauts Parise and Jernigan check helmets prior to training session

Science.gov (United States)

1994-01-01

Attired in training versions of the Shuttle partial-pressure launch and entry suits, payload specialist Dr. Ronald A Parise (left) and astronaut Tamara E. Jernigan, payload commander, check over their helmets prior to a training session. Holding the helmets is suit expert Alan M. Rochford, of NASA. The two were about to join their crew mates in a session of emergency bailout training at JSC's Weightless Environment Training Facility (WETF).

An Efficient Method for Image and Audio Steganography using Least Significant Bit (LSB) Substitution

Science.gov (United States)

Chadha, Ankit; Satam, Neha; Sood, Rakshak; Bade, Dattatray

2013-09-01

In order to improve the data hiding in all types of multimedia data formats such as image and audio and to make hidden message imperceptible, a novel method for steganography is introduced in this paper. It is based on Least Significant Bit (LSB) manipulation and inclusion of redundant noise as secret key in the message. This method is applied to data hiding in images. For data hiding in audio, Discrete Cosine Transform (DCT) and Discrete Wavelet Transform (DWT) both are used. All the results displayed prove to be time-efficient and effective. Also the algorithm is tested for various numbers of bits. For those values of bits, Mean Square Error (MSE) and Peak-Signal-to-Noise-Ratio (PSNR) are calculated and plotted. Experimental results show that the stego-image is visually indistinguishable from the original cover-image when nsteganography process does not reveal presence of any hidden message, thus qualifying the criteria of imperceptible message.

Methods of estimating the effect of integral motorcycle helmets on physiological and psychological performance.

Science.gov (United States)

Bogdan, Anna; Sudoł-Szopińska, Iwona; Luczak, Anna; Konarska, Maria; Pietrowski, Piotr

2012-01-01

This article proposes a method for a comprehensive assessment of the effect of integral motorcycle helmets on physiological and cognitive responses of motorcyclists. To verify the reliability of commonly used tests, we conducted experiments with 5 motorcyclists. We recorded changes in physiological parameters (heart rate, local skin temperature, core temperature, air temperature, relative humidity in the space between the helmet and the surface of the head, and the concentration of O(2) and CO(2) under the helmet) and in psychological parameters (motorcyclists' reflexes, fatigue, perceptiveness and mood). We also studied changes in the motorcyclists' subjective sensation of thermal comfort. The results made it possible to identify reliable parameters for assessing the effect of integral helmets on performance, i.e., physiological factors (head skin temperature, internal temperature and concentration of O(2) and CO(2) under the helmet) and on psychomotor factors (reaction time, attention and vigilance, work performance, concentration and a subjective feeling of mood and fatigue).

The effect of motorcycle helmet fit on estimating head impact kinematics from residual liner crush.

Science.gov (United States)

Bonin, Stephanie J; Gardiner, John C; Onar-Thomas, Arzu; Asfour, Shihab S; Siegmund, Gunter P

2017-09-01

Proper helmet fit is important for optimizing head protection during an impact, yet many motorcyclists wear helmets that do not properly fit their heads. The goals of this study are i) to quantify how a mismatch in headform size and motorcycle helmet size affects headform peak acceleration and head injury criteria (HIC), and ii) to determine if peak acceleration, HIC, and impact speed can be estimated from the foam liner's maximum residual crush depth or residual crush volume. Shorty-style helmets (4 sizes of a single model) were tested on instrumented headforms (4 sizes) during linear impacts between 2.0 and 10.5m/s to the forehead region. Helmets were CT scanned to quantify residual crush depth and volume. Separate linear regression models were used to quantify how the response variables (peak acceleration (g), HIC, and impact speed (m/s)) were related to the predictor variables (maximum crush depth (mm), crush volume (cm 3 ), and the difference in circumference between the helmet and headform (cm)). Overall, we found that increasingly oversized helmets reduced peak headform acceleration and HIC for a given impact speed for maximum residual crush depths less than 7.9mm and residual crush volume less than 40cm 3 . Below these levels of residual crush, we found that peak headform acceleration, HIC, and impact speed can be estimated from a helmet's residual crush. Above these crush thresholds, large variations in headform kinematics are present, possibly related to densification of the foam liner during the impact. Copyright © 2017 Elsevier Ltd. All rights reserved.

The effects of dynamic friction in oblique motorcycle helmet impacts

Science.gov (United States)

Bonugli, Enrique

The purpose of this study was to determine the frictional properties between the exterior surface of a motorcycle helmet and 'typical' roadway surfaces. These values were compared to abrasive papers currently recommended by government helmet safety standards and widely used by researchers in the field of oblique motorcycle helmet impacts. A guided freefall test fixture was utilized to obtain nominal impact velocities of 5, 7 and 9 m/s. The impacting surfaces were mounted to an angled anvil to simulate off-centered oblique collision. Head accelerations and impact forces were measured for each test. Analysis of the normal and tangential forces imparted to the contact surface indicated that the frictional properties of abrasive papers differ from asphalt and cement in magnitude, duration and onset. Reduction in head acceleration, both linear and angular, were observed when asphalt and cement were used as the impacting surface. Roofing shingle was determined to be a more suitable material to simulate 'typical' roadway surfaces however, this may not be ideal for use in a controlled laboratory setting. In a laboratory setting, the author recommends cement as a best-fit material to simulate roadway surface for use in oblique motorcycle helmet impacts since this material displayed characteristics that closely resemble asphalt and is currently used as a roadway construction material.

A digital input class-D audio amplifier with sixth-order PWM

International Nuclear Information System (INIS)

Luo Shumeng; Li Dongmei

2013-01-01

A digital input class-D audio amplifier with a sixth-order pulse-width modulation (PWM) modulator is presented. This modulator moves the PWM generator into the closed sigma—delta modulator loop. The noise and distortions generated at the PWM generator module are suppressed by the high gain of the forward loop of the sigma—delta modulator. Therefore, at the output of the modulator, a very clean PWM signal is acquired for driving the power stage of the class-D amplifier. A sixth-order modulator is designed to balance the performance and the system clock speed. Fabricated in standard 0.18 μm CMOS technology, this class-D amplifier achieves 110 dB dynamic range, 100 dB signal-to-noise rate, and 0.0056% total harmonic distortion plus noise. (semiconductor integrated circuits)

A Review on Successive Interference Cancellation Scheme Based on Optical CDMA Network

Science.gov (United States)

Alsowaidi, N.; Eltaif, T.; Mokhtar, M. R.

2014-12-01

Due to various desirable features of optical code division multiple access (OCDMA), it is believed this technique once developed and commercially available will be an integral part of optical access networks. Optical CDMA system suffers from a problem called multiple access interference (MAI) which limits the number of active users, it occurs when number of active users share the same carriers. The aim of this paper is to review successive interference cancellation (SIC) scheme based on optical CDMA system. The paper also reviews the system performance in presence of shot noise, thermal noise, and phase-induced intensity noise (PIIN). A comprehensive review on the mathematical model of SIC scheme using direct detection (DS) and spectral amplitude coding (SAC) were presented in this article.

Facial asymmetry correction with moulded helmet therapy in infants with deformational skull base plagiocephaly.

Science.gov (United States)

Kreutz, Matthias; Fitze, Brigitte; Blecher, Christoph; Marcello, Augello; Simon, Ruben; Cremer, Rebecca; Zeilhofer, Hans-Florian; Kunz, Christoph; Mayr, Johannes

2018-01-01

The recommendation issued by the American Academy of Pediatrics in the early 1990s to position infants on their back during sleep to prevent sudden infant death syndrome (SIDS) has dramatically reduced the number of deaths due to SIDS but has also markedly increased the prevalence of positional skull deformation in infants. Deformation of the base of the skull occurs predominantly in very severe deformational plagiocephaly and is accompanied by facial asymmetry, as well as an altered ear position, called ear shift. Moulded helmet therapy has become an accepted treatment strategy for infants with deformational plagiocephaly. The aim of this study was to determine whether facial asymmetry could be corrected by moulded helmet therapy. In this retrospective, single-centre study, we analysed facial asymmetry of 71 infants with severe deformational plagiocephaly with or without deformational brachycephaly who were undergoing moulded helmet therapy between 2009 and 2013. Computer-assisted, three-dimensional, soft-tissue photographic scanning was used to record the head shape before and after moulded helmet therapy. The distance between two landmarks in the midline of the face (i.e., root of the nose and nasal septum) and the right and left tragus were measured on computer-generated indirect and objective 3D photogrammetry images. A quotient was calculated between the two right- and left-sided distances to the midline. Quotients were compared before and after moulded helmet therapy. Infants without any therapy served as a control group. The median age of the infants before onset of moulded helmet therapy was 5 months (range 3-16 months). The median duration of moulded helmet therapy was 5 months (range 1-16 months). Comparison of the pre- and post-treatment quotients of the left vs. right distances measured between the tragus and root of the nose (n = 71) and nasal septum (n = 71) revealed a significant reduction of the asymmetry (Tragus-Nasion-Line Quotient: 0

1-Gb/s zero-pole cancellation CMOS transimpedance amplifier for Gigabit Ethernet applications

International Nuclear Information System (INIS)

Huang Beiju; Zhang Xu; Chen Hongda

2009-01-01

A zero-pole cancellation transimpedance amplifier (TIA) has been realized in 0.35 μm RF CMOS technology for Gigabit Ethernet applications. The TIA exploits a zero-pole cancellation configuration to isolate the input parasitic capacitance including photodiode capacitance from bandwidth deterioration. Simulation results show that the proposed TIA has a bandwidth of 1.9 GHz and a transimpedance gain of 65 dB·Ω for 1.5 pF photodiode capacitance, with a gain-bandwidth product of 3.4 THz·Ω. Even with 2 pF photodiode capacitance, the bandwidth exhibits a decline of only 300 MHz, confirming the mechanism of the zero-pole cancellation configuration. The input resistance is 50 Ω, and the average input noise current spectral density is 9.7 pA/√Hz. Testing results shows that the eye diagram at 1 Gb/s is wide open. The chip dissipates 17 mW under a single 3.3 V supply.

1-Gb/s zero-pole cancellation CMOS transimpedance amplifier for Gigabit Ethernet applications

Energy Technology Data Exchange (ETDEWEB)

Huang Beiju; Zhang Xu; Chen Hongda, E-mail: bjhuang@semi.ac.c [State Key Laboratory of Integrated Optoelectronics, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China)

2009-10-15

A zero-pole cancellation transimpedance amplifier (TIA) has been realized in 0.35 {mu}m RF CMOS technology for Gigabit Ethernet applications. The TIA exploits a zero-pole cancellation configuration to isolate the input parasitic capacitance including photodiode capacitance from bandwidth deterioration. Simulation results show that the proposed TIA has a bandwidth of 1.9 GHz and a transimpedance gain of 65 dB{center_dot}{Omega} for 1.5 pF photodiode capacitance, with a gain-bandwidth product of 3.4 THz{center_dot}{Omega}. Even with 2 pF photodiode capacitance, the bandwidth exhibits a decline of only 300 MHz, confirming the mechanism of the zero-pole cancellation configuration. The input resistance is 50 {Omega}, and the average input noise current spectral density is 9.7 pA/{radical}Hz. Testing results shows that the eye diagram at 1 Gb/s is wide open. The chip dissipates 17 mW under a single 3.3 V supply.

Iterative Soft Decision Interference Cancellation for DS-CDMA Employing the Distribution of Interference

Directory of Open Access Journals (Sweden)

Gerstacker WolfgangH

2010-01-01

Full Text Available A well-known receiver strategy for direct-sequence code-division multiple-access (DS-CDMA transmission is iterative soft decision interference cancellation. For calculation of soft estimates used for cancellation, the distribution of residual interference is commonly assumed to be Gaussian. In this paper, we analyze matched filter-based iterative soft decision interference cancellation (MF ISDIC when utilizing an approximation of the actual probability density function (pdf of residual interference. In addition, a hybrid scheme is proposed, which reduces computational complexity by considering the strongest residual interferers according to their pdf while the Gaussian assumption is applied to the weak residual interferers. It turns out that the bit error ratio decreases already noticeably when only a small number of residual interferers is regarded according to their pdf. For the considered DS-CDMA transmission the bit error ratio decreases by 80% for high signal-to-noise ratios when modeling all residual interferers but the strongest three to be Gaussian distributed.

Joint Service Aircrew Mask (JSAM) Rotary Wing (RW): MPU-5 Noise Attenuation Performance

Science.gov (United States)

2016-06-09

Flight helmets have been required to protect the pilot from potentially hazardous noise exposure and provide effective speech communication...hearing loss and hearing related disabilities and provide effective speech communication capabilities. Chemical/biological (CB) protective equipment has...distribution unlimited. 88ABW Cleared 08/24/2016; 88ABW-2016-4122. earcups attached to the retention with Velcro for adjustability

INTER LABORATORY COMBAT HELMET BLUNT IMPACT TEST METHOD COMPARISON

Science.gov (United States)

2018-03-26

data by Instrumentation for Impact  Test , SAE standard J211‐1 [4]. Although the entire curve is collected, the interest of this  project  team  solely...HELMET BLUNT IMPACT TEST METHOD COMPARISON by Tony J. Kayhart Charles A. Hewitt and Jonathan Cyganik March 2018 Final...INTER-LABORATORY COMBAT HELMET BLUNT IMPACT TEST METHOD COMPARISON 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR

Mitigation of MIMO Co-Channel Interference using robust interference cancellation receiver

DEFF Research Database (Denmark)

Rahman, Muhammad Imadur; De Carvalho, Elisabeth; Prasad, Ramjee

2007-01-01

(STBC) link may become equivalent to an interfering Spatial Multiplexing (SM) link. Using this knowledge and understanding, we propose an interference cancellation receiver robust to different types of MIMO interferers at cell edge for the Downlink (DL) of cellular systems. The receiver systematically...... performs a multiple symbol processing: this is the appropriate processing when the signal of interest or the signal of interferer is correlated across symbols, which is the case for STBC transmission. We evaluated different link combinations in terms of Signal to Interference and Noise Ratio (SINR......) statistics and Bit Error Rate (BER) performance in cellular Orthogonal Frequency Division Multiple Access (OFDMA) systems. We have found that the proposed multiple-symbol linear interference cancellation receiver performs satisfactorily when any kind of single 'logical' stream MIMO scheme is present...

Balanced homodyne detection of optical quantum states at audio-band frequencies and below

International Nuclear Information System (INIS)

Stefszky, M S; Mow-Lowry, C M; Chua, S S Y; Shaddock, D A; Buchler, B C; Lam, P K; McClelland, D E; Vahlbruch, H; Khalaidovski, A; Schnabel, R

2012-01-01

The advent of stable, highly squeezed states of light has generated great interest in the gravitational wave community as a means for improving the quantum-noise-limited performance of advanced interferometric detectors. To confidently measure these squeezed states, it is first necessary to measure the shot-noise across the frequency band of interest. Technical noise, such as non-stationary events, beam pointing, and parasitic interference, can corrupt shot-noise measurements at low Fourier frequencies, below tens of kilo-hertz. In this paper we present a qualitative investigation into all of the relevant noise sources and the methods by which they can be identified and mitigated in order to achieve quantum noise limited balanced homodyne detection. Using these techniques, flat shot-noise down to Fourier frequencies below 0.5 Hz is produced. This enables the direct observation of large magnitudes of squeezing across the entire audio-band, of particular interest for ground-based interferometric gravitational wave detectors. 11.6 dB of shot-noise suppression is directly observed, with more than 10 dB down to 10 Hz. (paper)

Classroom Audio Distribution in the Postsecondary Setting: A Story of Universal Design for Learning

Science.gov (United States)

Flagg-Williams, Joan B.; Bokhorst-Heng, Wendy D.

2016-01-01

Classroom Audio Distribution Systems (CADS) consist of amplification technology that enhances the teacher's, or sometimes the student's, vocal signal above the background noise in a classroom. Much research has supported the benefits of CADS for student learning, but most of it has focused on elementary school classrooms. This study investigated…

Spatio-Temporal Audio Enhancement Based on IAA Noise Covariance Matrix Estimates

DEFF Research Database (Denmark)

Nørholm, Sidsel Marie; Jensen, Jesper Rindom; Christensen, Mads Græsbøll

2014-01-01

A method for estimating the noise covariance matrix in a mul- tichannel setup is proposed. The method is based on the iter- ative adaptive approach (IAA), which only needs short seg- ments of data to estimate the covariance matrix. Therefore, the method can be used for fast varying signals....... The method is based on an assumption of the desired signal being harmonic, which is used for estimating the noise covariance matrix from the covariance matrix of the observed signal. The noise co- variance estimate is used in the linearly constrained minimum variance (LCMV) filter and compared...

Noise cancellation in magnetoencephalography and electroencephalography with isolated reference sensors

Science.gov (United States)

Kraus, Jr., Robert H.; Espy, Michelle A.; Matlachov, Andrei; Volegov, Petr

2010-06-01

An apparatus measures electromagnetic signals from a weak signal source. A plurality of primary sensors is placed in functional proximity to the weak signal source with an electromagnetic field isolation surface arranged adjacent the primary sensors and between the weak signal source and sources of ambient noise. A plurality of reference sensors is placed adjacent the electromagnetic field isolation surface and arranged between the electromagnetic isolation surface and sources of ambient noise.

The impact of mandatory helmet law on the outcome of maxillo facial trauma: a comparative study in kerala.

Science.gov (United States)

Usha, M; Ravindran, V; Soumithran, C S; Ravindran Nair, K S

2014-06-01

Motorcyclists comprise the majority of road-traffic victims in low and middle income countries,and consequently, the majority of the road-traffic victims globally. Simple measures can be taken to make safer on the roads, which include enforcement of safety measures like seat belt and helmets. The compulsory Helmet law was enforced in Kerala on 18/06/07. Resistance to legislation on motorcycle helmets still coexists world wide with debate on the effectiveness of helmets. In an attempt to analyze the protective effect of helmets on facial injuries a comparative study was conducted in Government Dental College, Calicut, which is a major trauma centre in northern Kerala. Data for the present study was obtained from the patients who have reported to the Emergency Department of Oral and Maxillofacial Surgery, Government Dental College, Calicut, for a period of 6 months immediately after the implementation of strict helmet rule in Kerala. For the study all patients with a history of nonfatal motor cycle accident sustaining facial injuries were included. The results were compared with the study conducted in the same institution in the pre law period. The study demonstrates the protective effect of motorcycle helmets in decreasing the morbidity of maxillofacial trauma.There was a marked decrease in incidence of motorcycle-related injuries, remarkable increase in helmet usage and better outcome in helmeted individuals in the post law period. Road traffic injury control is a public health problem. Health and medical professionals have an ethical responsibility to educate and arrange for the safety of individuals. Helmets are effective in preventing or reducing the severity of motorcycle-related injuries and in a developing country like India, enforced mandatory motor cycle helmet law is potentially one of the most cost effective interventions available.

A DESCRIPTIVE STUDY OF PATTERN OF FATAL HEAD INJURY IN HELMETED AND NONHELMETED VICTIMS OF TWO WHEELER ACCIDENTS

Directory of Open Access Journals (Sweden)

P. A. Sheeju

2016-07-01

Full Text Available BACKGROUND Motor vehicle crashes are a major cause of fatality all over the world. By 2020, motor vehicle injury is projected to become the third leading contributor to the global burden of disease in the world. Motor cyclists are about 25 times more likely than car occupants to die in Road Traffic Accidents. Data on the incidence and types of crashes is required to guide safety policy. Knowledge of how injuries are caused and of what type they are of valuable instrument for identifying interventions and monitoring the effectiveness of intervention. The present study was done to find out the factors that contribute for motor cycle crashes and to study the injury pattern seen in helmeted and non-helmeted victims. MATERIAL AND METHODS Victims of two wheeler accidents brought for autopsy in a Govt. Medical College were studied from October 2010 to August 2011. Two wheelers include motor cycles, scooters and mopeds. Bicycles were excluded from the study. Accidents include all types; against all types of vehicles running on the road, collision with any object, surface or any animal or fall from vehicle. The details of the accident were collected in a printed proforma from relative/witnesses and from police officials. The injuries were entered in the specific columns of proforma. Data was analysed with MS Excel. RESULTS Death due to head injury is more in non-helmeted (52.5% compared to helmeted drivers (43.8 % whereas injury to chest and abdomen and limbs are more in helmeted. Combination of injuries (Head+Chest+Abdomen predominated in helmeted drivers (18.8% compared to 5% in non-helmeted drivers. Spinal injuries were more in helmeted than in non-helmeted. CONCLUSION The pattern of head injury was analysed in detail in helmeted and non-helmeted drivers. This will help in detailing of pattern of head injury in both groups.

The Association Between Risk-taking Behavior and Helmet Use Among Motorcyclist

Science.gov (United States)

Trinh, Tu Anh; Phuong Linh Le, Thi

2018-04-01

The central aim of the research was to examine speeding behavior without helmet wearing among motorcycle riders in Ho Chi Minh City. The research model expanded the Theory of Planned Behavior by both psychological flow theory and sensation-seeking. 268 motorcyclists were involved in the research. A Confirmatory factor analysis and a Structural equation modeling were employed for model specification. The findings indicated a significant effect between predictors and the intention of speeding without helmet wearing. In addition, there was direct relation between intention and actual behavior. Also, sensation-seeking proved to be important in moderating predictors between the low-sensation-seeking motorcyclists and high-sensation-seeking ones. A deeper understanding of why motorcycle riders exceed the speed limit without wearing helmet played key role in changing their behavior.

Noise considerations for vital signs CW radar sensors

DEFF Research Database (Denmark)

Jensen, Brian Sveistrup; Jensen, Thomas; Zhurbenko, Vitaliy

2011-01-01

and the underlying signal theory for such sensors. Then to point out and especially clarify one of the most important effects aiding the design of vital signs radars (VSR), a more detailed discussion concerning phase noise cancellation (or filtering) by range correlation is given. This discussion leads to some...... general conclusions about which system components are the most critical concerning noise contribution and thus detection accuracy and dynamic range....

Audio-visual biofeedback for respiratory-gated radiotherapy: Impact of audio instruction and audio-visual biofeedback on respiratory-gated radiotherapy

International Nuclear Information System (INIS)

George, Rohini; Chung, Theodore D.; Vedam, Sastry S.; Ramakrishnan, Viswanathan; Mohan, Radhe; Weiss, Elisabeth; Keall, Paul J.

2006-01-01

Purpose: Respiratory gating is a commercially available technology for reducing the deleterious effects of motion during imaging and treatment. The efficacy of gating is dependent on the reproducibility within and between respiratory cycles during imaging and treatment. The aim of this study was to determine whether audio-visual biofeedback can improve respiratory reproducibility by decreasing residual motion and therefore increasing the accuracy of gated radiotherapy. Methods and Materials: A total of 331 respiratory traces were collected from 24 lung cancer patients. The protocol consisted of five breathing training sessions spaced about a week apart. Within each session the patients initially breathed without any instruction (free breathing), with audio instructions and with audio-visual biofeedback. Residual motion was quantified by the standard deviation of the respiratory signal within the gating window. Results: Audio-visual biofeedback significantly reduced residual motion compared with free breathing and audio instruction. Displacement-based gating has lower residual motion than phase-based gating. Little reduction in residual motion was found for duty cycles less than 30%; for duty cycles above 50% there was a sharp increase in residual motion. Conclusions: The efficiency and reproducibility of gating can be improved by: incorporating audio-visual biofeedback, using a 30-50% duty cycle, gating during exhalation, and using displacement-based gating

Foundations of Active Control - Active Noise Reduction Helmets

DEFF Research Database (Denmark)

Elmkjær, Torsten Haaber Leth

2008-01-01

rate is increased which in turn most likely also will lead to an increased ANR bandwidth. The hybrid system is also constituted from a continuous-time feedback system (FBS) and a discrete-time FBS. The continuous-time FBS is primarily responsible for additional broadband noise reduction, whereas...... the discrete-time FBS primarily is responsible for the attenuation of periodic signals. Owing to the requirement on causal operation of a physical AC system time delays will also to a large extent determine the achievable performance in FFS design and in particular in FBS design. A quantity referred...... on a head and torso simulator (HATS), is exposed to diffuse sound field illumination. By applying the JCRSA method the spatially-weighted-averaged acquisition lead times provided by the reference sensors relative to the performance sensors are estimated to be as much as 800-900μs. The thesis also includes...

Adaptive EMG noise reduction in ECG signals using noise level approximation

Science.gov (United States)

Marouf, Mohamed; Saranovac, Lazar

2017-12-01

In this paper the usage of noise level approximation for adaptive Electromyogram (EMG) noise reduction in the Electrocardiogram (ECG) signals is introduced. To achieve the adequate adaptiveness, a translation-invariant noise level approximation is employed. The approximation is done in the form of a guiding signal extracted as an estimation of the signal quality vs. EMG noise. The noise reduction framework is based on a bank of low pass filters. So, the adaptive noise reduction is achieved by selecting the appropriate filter with respect to the guiding signal aiming to obtain the best trade-off between the signal distortion caused by filtering and the signal readability. For the evaluation purposes; both real EMG and artificial noises are used. The tested ECG signals are from the MIT-BIH Arrhythmia Database Directory, while both real and artificial records of EMG noise are added and used in the evaluation process. Firstly, comparison with state of the art methods is conducted to verify the performance of the proposed approach in terms of noise cancellation while preserving the QRS complex waves. Additionally, the signal to noise ratio improvement after the adaptive noise reduction is computed and presented for the proposed method. Finally, the impact of adaptive noise reduction method on QRS complexes detection was studied. The tested signals are delineated using a state of the art method, and the QRS detection improvement for different SNR is presented.

Automatic helmet-wearing detection for law enforcement using CCTV cameras

Science.gov (United States)

Wonghabut, P.; Kumphong, J.; Satiennam, T.; Ung-arunyawee, R.; Leelapatra, W.

2018-04-01

The objective of this research is to develop an application for enforcing helmet wearing using CCTV cameras. The developed application aims to help law enforcement by police, and eventually resulting in changing risk behaviours and consequently reducing the number of accidents and its severity. Conceptually, the application software implemented using C++ language and OpenCV library uses two different angle of view CCTV cameras. Video frames recorded by the wide-angle CCTV camera are used to detect motorcyclists. If any motorcyclist without helmet is found, then the zoomed (narrow-angle) CCTV is activated to capture image of the violating motorcyclist and the motorcycle license plate in real time. Captured images are managed by database implemented using MySQL for ticket issuing. The results show that the developed program is able to detect 81% of motorcyclists on various motorcycle types during daytime and night-time. The validation results reveal that the program achieves 74% accuracy in detecting the motorcyclist without helmet.

Possibilities of an efficient noise damping in the large gas-fueled boilers

International Nuclear Information System (INIS)

1994-01-01

This report describes a series of tests with the objective to develop a technique for active control, and suppression of unstable conditions of combustion in gas-fired boiler systems. The primary target group for this report are persons within the energy sector, including especially users of natural gas. Focus has been given more to the practical possibilities and limitations than to complicated acoustical theory. The technical background for this work is constituted by the latest innovations within active noise cancelling methods for low frequent noise in channel- and pipe shaped systems, such as heating-, air-and exhaust systems. The fundamental idea has been to implement already functioning and commercial available systems for active noise cancellation in an modified setup to a gasfired boiler system. A few examples of similar attempts are given. Latest a relatively successful example of actively controlling an unstable combustion in a channel shaped burner system (CNRS Paris 1993). The conclusion of the project is anyway, that unstable combustion in larger gasfired boilers can not be controlled by the active methods and systems known today. The reasons for this are: the flame and thus the noise source are distributed in space, the acoustical wave-propagation in the combustion chamber is complex and with low damping, several loops for unstable combustion are possible. Within this project special sensors for high temperatures are developed, e.g.: probe microphones, high temperature turbulence screens and a system for measuring of the variations in UV-light emission form the flame. These systems are applicable also for more 'traditional active noise cancellation' of low-frequent noise in exhaust pipes and chimneys. (au)

[Research on electrocardiogram de-noising algorithm based on wavelet neural networks].

Science.gov (United States)

Wan, Xiangkui; Zhang, Jun

2010-12-01

In this paper, the ECG de-noising technology based on wavelet neural networks (WNN) is used to deal with the noises in Electrocardiogram (ECG) signal. The structure of WNN, which has the outstanding nonlinear mapping capability, is designed as a nonlinear filter used for ECG to cancel the baseline wander, electromyo-graphical interference and powerline interference. The network training algorithm and de-noising experiments results are presented, and some key points of the WNN filter using ECG de-noising are discussed.

Influence of humidification on comfort during noninvasive ventilation with a helmet.

Science.gov (United States)

Ueta, Kazuyoshi; Tomita, Toshiji; Uchiyama, Akinori; Ohta, Noriyuki; Iguchi, Naoya; Goto, Yukiko; Fujino, Yuji

2013-05-01

To evaluate optimal humidifier water temperature when using a helmet for noninvasive ventilation. Twenty-eight healthy individuals underwent 8 cm H2O CPAP ventilation with FIO2 of 0.21 and 0.5. Each was sequentially tested in the following order: using the helmet without humidification at ambient temperature; with humidification with unheated chamber water; and with humidification with the chamber water at 31°C, 34°C, and 37°C. At each setting, after a 20 min stabilization period, measurements were taken. Comfort level at each setting was evaluated using a visual analog scale rated zero (least comfortable) to 10 (most comfortable). Temperature and relative and absolute humidity inside the helmet increased; however, the comfort scores significantly decreased as the humidification chamber water temperature increased. Regardless of the FIO2, statistically significantly highest comfort scores were obtained when humidification water, with and without active humidification, was at ambient temperature. Unacceptable absolute humidity was obtained only without humidification at room temperature when FIO2 was 0.5. With the clinical use of a helmet, for patient comfort and mucosal humidification during CPAP, the most desirable conditions are likely to be obtained by humidifying without heating, that is by leaving the water in the humidifier chamber at room temperature.

Development of a helmet-mounted PLZT thermal/flash protection system

International Nuclear Information System (INIS)

Harris, J.O. Jr.; Cutchen, J.T.; Pfoff, B.J.

1976-01-01

Sandia Laboratories is developing PLZT thermal/flash protective devices (TFPD's) goggles to prevent exposure and resultant eye damage from nuclear weapon detonations. The primary emphasis of the present program is to transfer technology and establish production capability for helmet-mounted PLZT/TFPD goggles for USAF flight crews, with a non-helmet-mounted configuration to follow. The first production units are anticipated in the fall of 1977. The operating principles of the PLZT/TFPD goggle device are briefly outlined, and the device configuration and operational characteristics are described

Scientific journal cancellations

CERN Multimedia

The Library

2001-01-01

Earlier this year the Scientific Information Policy Board (SIPB) requested the Library and the Working Group for Acquisitions to revise the current printed journal collection in order to cancel those titles that are less required. Savings could then be used for the development of other collections and particularly electronic resources needed to support CERN current research activities. A list of proposed cancellations was drawn and posted on the Library web pages: http://library.cern.ch/library_general/cancel.html The SIPB invites every one to check if any of the titles are of importance to their work, in which case you are invited to inform the Library before the 25th of September by sending an e-mail to: eliane.chaney@cern.ch Titles not reconsidered by the users will be cancelled by the end of the year. Thank you, The Library

Estimation of inhalation flow profile using audio-based methods to assess inhaler medication adherence

Science.gov (United States)

Lacalle Muls, Helena; Costello, Richard W.; Reilly, Richard B.

2018-01-01

Asthma and chronic obstructive pulmonary disease (COPD) patients are required to inhale forcefully and deeply to receive medication when using a dry powder inhaler (DPI). There is a clinical need to objectively monitor the inhalation flow profile of DPIs in order to remotely monitor patient inhalation technique. Audio-based methods have been previously employed to accurately estimate flow parameters such as the peak inspiratory flow rate of inhalations, however, these methods required multiple calibration inhalation audio recordings. In this study, an audio-based method is presented that accurately estimates inhalation flow profile using only one calibration inhalation audio recording. Twenty healthy participants were asked to perform 15 inhalations through a placebo Ellipta™ DPI at a range of inspiratory flow rates. Inhalation flow signals were recorded using a pneumotachograph spirometer while inhalation audio signals were recorded simultaneously using the Inhaler Compliance Assessment device attached to the inhaler. The acoustic (amplitude) envelope was estimated from each inhalation audio signal. Using only one recording, linear and power law regression models were employed to determine which model best described the relationship between the inhalation acoustic envelope and flow signal. Each model was then employed to estimate the flow signals of the remaining 14 inhalation audio recordings. This process repeated until each of the 15 recordings were employed to calibrate single models while testing on the remaining 14 recordings. It was observed that power law models generated the highest average flow estimation accuracy across all participants (90.89±0.9% for power law models and 76.63±2.38% for linear models). The method also generated sufficient accuracy in estimating inhalation parameters such as peak inspiratory flow rate and inspiratory capacity within the presence of noise. Estimating inhaler inhalation flow profiles using audio based methods may be

Analysis of power tiller noise using diesel-biodiesel fuel blends

OpenAIRE

N Keramat Siavash; Gh Najafi; S. R Hassan Beigi Bidgoli; B Ghobadian

2015-01-01

Introduction: There are several sources of noise in an industrial and agriculture environment. Machines with rotating or reciprocating engines are sound-producing sources. Also, the audio signal can be analyzed to discover how well a machine operates. Diesel engines complex noise SPL and sound frequency content both strongly depend on fuel combustion, which produces the so-called combustion noise. Actually, the unpleasant sound signature of diesel engines is due to the harsh and irregular sel...

Design of a Helmet Liner for Improved Low Velocity Impact Protection

Science.gov (United States)

2013-05-01

FIGURE 14. MONORAIL DROP TEST WITH DOT-SIZE C HEADFORM AND HEMISPHERICAL ANVIL ........................... 14  FIGURE 15. ACH PAD CONFIGURATION. LEFT...materials. In this project, the monorail drop test device, used for the helmeted headform drop test, was modified for material testing as shown in Figure...a guided free fall drop test using a monorail drop test apparatus as shown in Figure 14. All helmets tested in this study were ACH-Size Large and

Examination of factors associated with use rates after transition from a universal to partial motorcycle helmet use law.

Science.gov (United States)

Russo, Brendan J; Barrette, Timothy P; Morden, Jeffery; Savolainen, Peter T; Gates, Timothy J

2017-01-02

Motorcycle riders account for a disproportionately high number of traffic injuries and fatalities compared to occupants of other vehicle types. Though research has demonstrated the benefits of helmet use in preventing serious and fatal injuries in the event of a crash, helmet use has remained relatively stable in the United States, where the most recent national estimates show a 64% use rate. Use rates have been markedly lower among those states that do not have a universal helmet law for all riders. In 2012, the state of Michigan repealed its longstanding mandatory helmet use law. In order to gain insights as to the effects of this legislative change, a study was conducted to examine short-term changes in helmet use and identify factors associated with use rates. A statewide direct observation survey was conducted 1 year after the transition from a universal helmet law to a partial helmet law. A random parameters logistic regression model was estimated to identify motorcyclist, roadway, and environmental characteristics associated with helmet use. This modeling framework accounts for both intravehicle correlation (between riders and passengers on the same motorcycle) as well as unobserved heterogeneity across riders due to important unobserved factors. Helmet use was shown to vary across demographic segments of the motorcyclist population. Use rates were higher among Caucasian riders, as well as among those age 60 and above. No significant difference was observed between male and female riders. Use was also found to vary geographically, temporally, and with respect to various environmental characteristics. Geographically, helmet use rates tended to be correlated with historical restraint use trends, which may be reflective of riding environment and general differences in the riding population. To this end, rates were also highly variable based upon the type of motorcycle and whether the motorcyclist was wearing high-visibility gear. The study results demonstrate

HElmet therapy Assessment in infants with Deformed Skulls (HEADS: protocol for a randomised controlled trial

Directory of Open Access Journals (Sweden)

van Wijk Renske M

2012-07-01

Full Text Available Abstract Background In The Netherlands, helmet therapy is a commonly used treatment in infants with skull deformation (deformational plagiocephaly or deformational brachycephaly. However, evidence of the effectiveness of this treatment remains lacking. The HEADS study (HElmet therapy Assessment in Deformed Skulls aims to determine the effects and costs of helmet therapy compared to no helmet therapy in infants with moderate to severe skull deformation. Methods/design Pragmatic randomised controlled trial (RCT nested in a cohort study. The cohort study included infants with a positional preference and/or skull deformation at two to four months (first assessment. At 5 months of age, all children were assessed again and infants meeting the criteria for helmet therapy were asked to participate in the RCT. Participants were randomly allocated to either helmet therapy or no helmet therapy. Parents of eligible infants that do not agree with enrolment in the RCT were invited to stay enrolled for follow up in a non-randomisedrandomised controlled trial (nRCT; they were then free to make the decision to start helmet therapy or not. Follow-up assessments took place at 8, 12 and 24 months of age. The main outcome will be head shape at 24 months that is measured using plagiocephalometry. Secondary outcomes will be satisfaction of parents and professionals with the appearance of the child, parental concerns about the future, anxiety level and satisfaction with the treatment, motor development and quality of life of the infant. Finally, compliance and costs will also be determined. Discussion HEADS will be the first study presenting data from an RCT on the effectiveness of helmet therapy. Outcomes will be important for affected children and their parents, health care professionals and future treatment policies. Our findings are likely to influence the reimbursement policies of health insurance companies. Besides these health outcomes, we will be able to

Impulse Noise Cancellation of Medical Images Using Wavelet Networks and Median Filters

Science.gov (United States)

Sadri, Amir Reza; Zekri, Maryam; Sadri, Saeid; Gheissari, Niloofar

2012-01-01

This paper presents a new two-stage approach to impulse noise removal for medical images based on wavelet network (WN). The first step is noise detection, in which the so-called gray-level difference and average background difference are considered as the inputs of a WN. Wavelet Network is used as a preprocessing for the second stage. The second step is removing impulse noise with a median filter. The wavelet network presented here is a fixed one without learning. Experimental results show that our method acts on impulse noise effectively, and at the same time preserves chromaticity and image details very well. PMID:23493998

Digital signal processor for silicon audio playback devices; Silicon audio saisei kikiyo digital signal processor

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The digital audio signal processor (DSP) TC9446F series has been developed silicon audio playback devices with a memory medium of, e.g., flash memory, DVD players, and AV devices, e.g., TV sets. It corresponds to AAC (advanced audio coding) (2ch) and MP3 (MPEG1 Layer3), as the audio compressing techniques being used for transmitting music through an internet. It also corresponds to compressed types, e.g., Dolby Digital, DTS (digital theater system) and MPEG2 audio, being adopted for, e.g., DVDs. It can carry a built-in audio signal processing program, e.g., Dolby ProLogic, equalizer, sound field controlling, and 3D sound. TC9446XB has been lined up anew. It adopts an FBGA (fine pitch ball grid array) package for portable audio devices. (translated by NEDO)

Determinants of helmet use behaviour among employed motorcycle riders in Yazd, Iran based on theory of planned behaviour.

Science.gov (United States)

Ali, Mehri; Saeed, Mazloomy Mahmoodabad Seyed; Ali, Morowatisharifabad Mohammad; Haidar, Nadrian

2011-09-01

This paper reports on predictors of helmet use behaviour, using variables based on the theory of planned behaviour model among the employed motorcycle riders in Yazd-Iran, in an attempt to identify influential factors that may be addressed through intervention efforts. In 2007, a cluster random sample of 130 employed motorcycle riders in the city of Yazd in central Iran, participated in the study. Appropriate instruments were designed to measure the variables of interest (attitude, subjective norms, perceived behaviour control, intention along with helmet use behaviour). Reliability and validity of the instruments were examined and approved. The statistical analysis of the data included descriptive statistics, bivariate correlations, and multiple regression. Based on the results, 56 out of all the respondents (43.1%) had history of accident by motorcycle. Of these motorcycle riders only 10.7% were wearing their helmet at the time of their accident. Intention and perceived behavioural control showed a significant relationship with helmet use behaviour and perceived behaviour control was the strongest predictor of helmet use intention, followed by subjective norms, and attitude. It was found that that helmet use rate among motorcycle riders was very low. The findings of present study provide a preliminary support for the TPB model as an effective framework for examining helmet use in motorcycle riders. Understanding motorcycle rider's thoughts, feelings and beliefs about helmet use behaviour can assist intervention specialists to develop and implement effective programs in order to promote helmet use among motorcycle riders. Copyright © 2010 Elsevier Ltd. All rights reserved.

Motorcycle helmet use and the risk of head, neck, and fatal injury: Revisiting the Hurt Study.

Science.gov (United States)

Rice, Thomas M; Troszak, Lara; Ouellet, James V; Erhardt, Taryn; Smith, Gordon S; Tsai, Bor-Wen

2016-06-01

Most studies find strong evidence that motorcycle helmets protect against injury, but a small number of controversial studies have reported a positive association between helmet use and neck injury. The most commonly cited paper is that of Goldstein (1986). Goldstein obtained and reanalyzed data from the Hurt Study, a prospective, on-scene investigation of 900 motorcycle collisions in the city of Los Angeles. The Goldstein results have been adopted by the anti-helmet community to justify resistance to compulsory motorcycle helmet use on the grounds that helmets may cause neck injuries due to their mass. In the current study, we replicated Goldstein's models to understand how he obtained his unexpected results, and we then applied modern statistical methods to estimate the association of motorcycle helmet use with head injury, fatal injury, and neck injury among collision-involved motorcyclists. We found Goldstein's analysis to be critically flawed due to improper data imputation, modeling of extremely sparse data, and misinterpretation of model coefficients. Our new analysis showed that motorcycle helmets were associated with markedly lower risk of head injury (RR 0.40, 95% CI 0.31-0.52) and fatal injury (RR 0.44, 95% CI 0.26-0.74) and with moderately lower but statistically significant risk of neck injury (RR 0.63, 95% CI 0.40-0.99), after controlling for multiple potential confounders. Copyright © 2016 Elsevier Ltd. All rights reserved.

Motorcycle helmet type and the risk of head injury and neck injury during motorcycle collisions in California.

Science.gov (United States)

Erhardt, Taryn; Rice, Thomas; Troszak, Lara; Zhu, Motao

2016-01-01

The use of novelty motorcycle helmets is often prompted by beliefs that wearing a standard helmet can contribute to neck injury during traffic collisions. The goal of this analysis was to examine the association between helmet type and neck injury risk and the association between helmet type and head injury. Data were collected during the investigation of motorcycle collisions of any injury severity by the California Highway Patrol (CHP) and 83 local law enforcement agencies in California between June 2012 and July 2013. We estimated head injury and neck injury risk ratios from data on 7051 collision-involved motorcyclists using log-binomial regression. Helmet type was strongly associated with head injury occurrence but was not associated with the occurrence of neck injury. Rider age, rider alcohol use, and motorcycle speed were strong, positive predictors of both head and neck injury. Interventions to improve motorcycle helmet choice and to counteract misplaced concerns surrounding neck injury risk are likely to lead to reductions in head injury, brain injury, and death. Copyright © 2015 Elsevier Ltd. All rights reserved.

Influence of socioeconomic status on the effectiveness of bicycle helmet legislation for children: a prospective observational study.

Science.gov (United States)

Parkin, Patricia C; Khambalia, Amina; Kmet, Leanne; Macarthur, Colin

2003-09-01

To evaluate the influence of average family income in a geographic area on the effectiveness of helmet legislation on observed helmet use by children (5-14 years). The study was conducted in East York, a health district of Metropolitan Toronto, in collaboration with the East York Health Unit. In 1996, the total population was 107 822, 11 340 of which were children 5 to 14 years. Census data were used to group the 21 census tracts in East York into 7 geographically distinct areas. The boundaries of these areas are natural barriers to travel, such as expressways, ravines, railway tracks, and hydroelectric power lines. The areas were also ranked according to average family income (based on Statistics Canada data). For analytical purposes, areas were defined as low-, mid-, and high-income areas. Census data profiles of the areas have been previously described. For each consecutive year from 1990 to 1997 inclusive, direct observations of children riding bicycles in East York during the months of April through October were made. In 1995, observations were completed before the introduction of the law on October 1, 1995. Only children who were between 5 and 14 years of age and riding a 2-wheeled bicycle were included in the study. In total, 111 sites across all 7 areas were selected for observation. Observational sites included school yards of all elementary and middle schools (kindergarten to grade 8) and all parks in East York. In addition, 5 major intersections and 5 residential streets from each area were randomly selected. Observers were trained and used a standardized data collection form. A pilot study showed that the data collected by observers were reliable and valid. Observers remained at each site for 1 hour and collected data on helmet use and sex. Ethical approval for the study was obtained from the Hospital for Sick Children Research Ethics Board, the East York Board of Education, and the Metropolitan Separate School Board. The proportion of children who were

Design of low noise transimpedance amplifier for intravascular ultrasound

KAUST Repository

Reda, Dina

2009-11-01

In this paper, we study transimpedance amplifiers for capacitive sensing applications with a focus on Intravascular Ultra Sound (IVUS). We employ RF noise cancellation technique on capacitive feedback based transimpedance amplifiers. This technique eliminates the input-referred noise of TIAs completely and enhances the dynamic range of front-end electronics. Simulation results verify the proposed technique used in two different TIA topologies employing shunt-shunt feedback. ©2009 IEEE.

Helmet "tang" from the Metropolitan Museum of Art (New York City, United States. Features of Construction, Design and Operational Use

Directory of Open Access Journals (Sweden)

Leonid A. Bobrov

2016-12-01

Full Text Available The article discusses iron helmet (No. 36.25.115, which is stored in the Metropolitan Museum of art (New York City, United States. For the first time this helmet was published and analyzed by American scientists G. C. Stone and D.G. Alexander. The analysis showed that the Bowl was made by Turkish masters of the XVII century and backplate and the hoop is added to the helmet in 1781–1782 D.G. Alexander speculated that the helmet belonged to the Warrior of the Crimean Khanate. Dating the helmet does not raise objections. However, the attribution of a helmet requires some clarification. Analysis of the design of the helmet and decoration revealed that backplate, hoop and Aventail from iron rings added to Bowl in 1781–1782, were manufactured by Circassian craftsmen living in the Northern Caucasus or in Crimea. For the decoration of the helmet has been used typical Circassian ornaments: "sieve", cherkessian floral pattern, geometric shapes, triangular in shape, "gear", etc. During Assembly of the helmet were applied characteristic of Circassian gunsmiths technological solutions: using as a basis the bowl old-style helmet, tapered Finial with a ring for a decorative plume, hoop with four plates, ringed with aventail lip to protect the forehead, etc. In Circassia similar headgear worn were known as tang (from the Arabic. "Taj", i.e., the "Crown". In the XVII–XVIII centuries. they willingly purchased representatives of Crimean Tatar nobility. Similar in design and system design helmets Circassian production belonged to the highest aristocracy of the Crimean Khanate, are stored in Museum and private collections in Poland, Turkey and the United States. The inscription "Bekmurun" on the hoop from the Metropolitan helmet suggests that it was manufactured on request of Kabardian Bekmur princely heir (Bekmurziny, which moved from Circassia in Crimea, 1737. The popularity of tang type helmets among the aristocracy of North Caucasus and Crimea were due not

Behavioural and biochemical stress responses of Palinurus elephas after exposure to boat noise pollution in tank.

Science.gov (United States)

Filiciotto, Francesco; Vazzana, Mirella; Celi, Monica; Maccarrone, Vincenzo; Ceraulo, Maria; Buffa, Gaspare; Di Stefano, Vincenzo; Mazzola, Salvatore; Buscaino, Giuseppa

2014-07-15

This study examined the effects of boat noise on the behavioural and biochemical parameters of the Mediterranean spiny lobster (Palinurus elephas). The experiment was conducted in a tank equipped with a video and audio recording system. 18 experimental trials, assigned to boat noise and control conditions, were performed using lobsters in single and group of 4 specimens. After a 1h habituation period, we audio- and video-recorded the lobsters for 1h. During the experimental phase, the animals assigned to the boat groups were exposed to boat noise pollution (a random sequence of boat noises). Exposure to the noise produced significant variations in locomotor behaviours and haemolymphatic parameters. Our results indicate that the lobsters exposed to boat noises increased significantly their locomotor activities and haemolymphatic bioindicator of stressful conditions such as glucose, total proteins, Hsp70 expression and THC when tested both singly and in groups. Copyright © 2014 Elsevier Ltd. All rights reserved.

Feasibility of nitric oxide administration by neonatal helmet-CPAP: a bench study.

Science.gov (United States)

Trevisanuto, Daniele; Doglioni, Nicoletta; Micaglio, Massimo; Zanardo, Vincenzo

2007-09-01

Inhaled nitric oxide (NO) may have a role in the treatment of preterm infants with respiratory failure. We evaluated the feasibility of administering NO therapy by a new continuous positive airway pressure (CPAP) system (neonatal helmet-CPAP). While maintaining a constant total flow of 8, 10, and 12 l.min(-1), NO concentrations were progressively increased to 5, 10, 20, and 40 p.p.m. in the neonatal helmet-CPAP pressure chamber (5 cmH2O). NO, NO2, and O2 concentrations were measured in the pressure chamber and the immediate external environment. In the chamber, NO2 levels remained low (neonatal helmet-CPAP system. This method allows the delivery of accurate NO levels and high O2 concentrations avoiding NO2 accumulation. Further experimental and clinical studies are needed.

Adaptive cancellation of geomagnetic background noise for magnetic anomaly detection using coherence

International Nuclear Information System (INIS)

Liu, Dunge; Xu, Xin; Huang, Chao; Zhu, Wanhua; Liu, Xiaojun; Fang, Guangyou; Yu, Gang

2015-01-01

Magnetic anomaly detection (MAD) is an effective method for the detection of ferromagnetic targets against background magnetic fields. Currently, the performance of MAD systems is mainly limited by the background geomagnetic noise. Several techniques have been developed to detect target signatures, such as the synchronous reference subtraction (SRS) method. In this paper, we propose an adaptive coherent noise suppression (ACNS) method. The proposed method is capable of evaluating and detecting weak anomaly signals buried in background geomagnetic noise. Tests with real-world recorded magnetic signals show that the ACNS method can excellently remove the background geomagnetic noise by about 21 dB or more in high background geomagnetic field environments. Additionally, as a general form of the SRS method, the ACNS method offers appreciable advantages over the existing algorithms. Compared to the SRS method, the ACNS algorithm can eliminate the false target signals and represents a noise suppressing capability improvement of 6.4 dB. The positive outcomes in terms of intelligibility make this method a potential candidate for application in MAD systems. (paper)

Categorizing Video Game Audio

DEFF Research Database (Denmark)

Westerberg, Andreas Rytter; Schoenau-Fog, Henrik

2015-01-01

they can use audio in video games. The conclusion of this study is that the current models' view of the diegetic spaces, used to categorize video game audio, is not t to categorize all sounds. This can however possibly be changed though a rethinking of how the player interprets audio.......This paper dives into the subject of video game audio and how it can be categorized in order to deliver a message to a player in the most precise way. A new categorization, with a new take on the diegetic spaces, can be used a tool of inspiration for sound- and game-designers to rethink how...

Signal shaping and tail cancellation for gas proportional detectors at high counting rates

International Nuclear Information System (INIS)

Boie, R.A.; Hrisoho, A.T.; Rehak, P.

1982-01-01

A low noise, wide bandwidth preamplifier and signal processing filter were developed for high counting rate proportional counters. The filter consists of a seven pole Gaussian integrator with symmetrical weighting function and continuously variable shaping time, tausub(s), of 8-50 ns (fwhm) preceded by a second order pole/zero circuit which cancels the long (1/t) tails of the chamber signals. The preamplifier is an optimized common base input design with 2 ns rise time and an equivalent noise input charge < 2000 r.m.s. electrons, when connected to a chamber with 10 pF capacitance and at a filtering time, tausub(s), of 10 ns. (orig.)

Implementation and Analysis Audio Steganography Used Parity Coding for Symmetric Cryptography Key Delivery

Directory of Open Access Journals (Sweden)

Afany Zeinata Firdaus

2013-12-01

Full Text Available In today's era of communication, online data transactions is increasing. Various information even more accessible, both upload and download. Because it takes a capable security system. Blowfish cryptographic equipped with Audio Steganography is one way to secure the data so that the data can not be accessed by unauthorized parties. In this study Audio Steganography technique is implemented using parity coding method that is used to send the key cryptography blowfish in e-commerce applications based on Android. The results obtained for the average computation time on stage insertion (embedding the secret message is shorter than the average computation time making phase (extracting the secret message. From the test results can also be seen that the more the number of characters pasted the greater the noise received, where the highest SNR is obtained when a character is inserted as many as 506 characters is equal to 11.9905 dB, while the lowest SNR obtained when a character is inserted as many as 2006 characters at 5,6897 dB . Keywords: audio steganograph, parity coding, embedding, extractin, cryptography blowfih.

High-Fidelity Piezoelectric Audio Device

Science.gov (United States)

Woodward, Stanley E.; Fox, Robert L.; Bryant, Robert G.

2003-01-01

ModalMax is a very innovative means of harnessing the vibration of a piezoelectric actuator to produce an energy efficient low-profile device with high-bandwidth high-fidelity audio response. The piezoelectric audio device outperforms many commercially available speakers made using speaker cones. The piezoelectric device weighs substantially less (4 g) than the speaker cones which use magnets (10 g). ModalMax devices have extreme fabrication simplicity. The entire audio device is fabricated by lamination. The simplicity of the design lends itself to lower cost. The piezoelectric audio device can be used without its acoustic chambers and thereby resulting in a very low thickness of 0.023 in. (0.58 mm). The piezoelectric audio device can be completely encapsulated, which makes it very attractive for use in wet environments. Encapsulation does not significantly alter the audio response. Its small size (see Figure 1) is applicable to many consumer electronic products, such as pagers, portable radios, headphones, laptop computers, computer monitors, toys, and electronic games. The audio device can also be used in automobile or aircraft sound systems.

30 CFR 250.181 - When may the Secretary cancel my lease and when am I compensated for cancellation?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false When may the Secretary cancel my lease and when... may the Secretary cancel my lease and when am I compensated for cancellation? If the Secretary cancels.... Section 250.185 states conditions under which you will receive no compensation. The Secretary may cancel a...

Societal cost of traumatic brain injury: A comparison of cost-of-injuries related to biking with and without helmet use.

Science.gov (United States)

Costa, Camille K; Dagher, Jehane H; Lamoureux, Julie; de Guise, Elaine; Feyz, Mitra

2015-01-01

The goal of this study is to determine if a difference in societal costs exists from traumatic brain injuries (TBI) in patients who wear helmets compared to non-wearers. This is a retrospective cost-of-injury study of 128 patients admitted to the Montreal General Hospital (MGH) following a TBI that occurred while cycling between 2007-2011. Information was collected from Quebec Trauma Registry. The independent variables collected were socio-demographic, helmet status, clinical and neurological patient information. The dependent variables evaluated societal costs. The median costs of hospitalization were significantly higher (p = 0.037) in the no helmet group ($7246.67 vs. $4328.17). No differences in costs were found for inpatient rehabilitation (p = 0.525), outpatient rehabilitation (p = 0.192), loss of productivity (p = 0.108) or death (p = 1.000). Overall, the differences in total societal costs between the helmet and no helmet group were not significantly different (p = 0.065). However, the median total costs for patients with isolated TBI in the non-helmet group ($22, 232.82) was significantly higher (p = 0.045) compared to the helmet group ($13, 920.15). Cyclists sustaining TBIs who did not wear helmets in this study were found to cost society nearly double that of helmeted cyclists.

The effect of helmet use on injury severity and crash circumstances in skiers and snowboarders.

Science.gov (United States)

Hagel, Brent; Pless, I Barry; Goulet, Claude; Platt, Robert; Robitaille, Yvonne

2005-01-01

The aim of this study was to examine the effect of helmet use on non-head-neck injury severity and crash circumstances in skiers and snowboarders. We used a matched case-control study over the November 2001 to April 2002 winter season. 3295 of 4667 injured skiers and snowboarders reporting to the ski patrol at 19 areas in Quebec with non-head, non-neck injuries agreed to participate. Cases included those evacuated by ambulance, admitted to hospital, with restriction of normal daily activities (NDAs) >6 days, with non-helmet equipment damage, fast self-reported speed, participating on a more difficult run than usual, and jumping-related injury. Controls were injured participants without severe injuries or high-energy crash circumstances and were matched to cases on ski area, activity, day, age, and sex. Conditional logistic regression was used to relate each outcome to helmet use. There was no evidence that helmet use increased the risk of severe injury or high-energy crash circumstances. The results suggest that helmet use in skiing and snowboarding is not associated with riskier activities that lead to non-head-neck injuries.

Impact of helmet use on traumatic brain injury from road traffic accidents in Cambodia.

Science.gov (United States)

Gupta, Saksham; Klaric, Katherine; Sam, Nang; Din, Vuthy; Juschkewitz, Tina; Iv, Vycheth; Shrime, Mark G; Park, Kee B

2018-01-02

Rapid urbanization and motorization without corresponding increases in helmet usage have made traumatic brain injury due to road traffic accidents a major public health crisis in Cambodia. This analysis was conducted to quantify the impact of helmets on severity of injury, neurosurgical indication, and functional outcomes at discharge for motorcycle operators who required hospitalization for a traumatic brain injury following a road traffic accident in Cambodia. The medical records of 491 motorcycle operators who presented to a major tertiary care center in Cambodia with traumatic brain injury were retrospectively analyzed using multivariate logistic regression. The most common injuries at presentation were contusions (47.0%), epidural hematomas (30.1%), subdural hematomas (27.9%), subarachnoid hemorrhages (12.4%), skull fractures (21.4%), and facial fractures (18.5%). Moderate-to-severe loss of consciousness was present in 36.3% of patients. Not wearing a helmet was associated with an odds ratio of 2.20 (95% confidence interval [CI], 1.15-4.22) for presenting with moderate to severe loss of consciousness compared to helmeted patients. Craniotomy or craniectomy was indicated for evacuation of hematoma in 20.0% of cases, and nonhelmeted patients had 3.21-fold higher odds of requiring neurosurgical intervention (95% CI, 1.25-8.27). Furthermore, lack of helmet usage was associated with 2.72-fold higher odds of discharge with functional deficits (95% CI, 1.14-6.49). In total, 30.1% of patients were discharged with severe functional deficits. Helmets demonstrate a protective effect and may be an effective public health intervention to significantly reduce the burden of traumatic brain injury in Cambodia and other developing countries with increasing rates of motorization across the world.

Detection and characterization of lightning-based sources using continuous wavelet transform: application to audio-magnetotellurics

Science.gov (United States)

Larnier, H.; Sailhac, P.; Chambodut, A.

2018-01-01

Atmospheric electromagnetic waves created by global lightning activity contain information about electrical processes of the inner and the outer Earth. Large signal-to-noise ratio events are particularly interesting because they convey information about electromagnetic properties along their path. We introduce a new methodology to automatically detect and characterize lightning-based waves using a time-frequency decomposition obtained through the application of continuous wavelet transform. We focus specifically on three types of sources, namely, atmospherics, slow tails and whistlers, that cover the frequency range 10 Hz to 10 kHz. Each wave has distinguishable characteristics in the time-frequency domain due to source shape and dispersion processes. Our methodology allows automatic detection of each type of event in the time-frequency decomposition thanks to their specific signature. Horizontal polarization attributes are also recovered in the time-frequency domain. This procedure is first applied to synthetic extremely low frequency time-series with different signal-to-noise ratios to test for robustness. We then apply it on real data: three stations of audio-magnetotelluric data acquired in Guadeloupe, oversea French territories. Most of analysed atmospherics and slow tails display linear polarization, whereas analysed whistlers are elliptically polarized. The diversity of lightning activity is finally analysed in an audio-magnetotelluric data processing framework, as used in subsurface prospecting, through estimation of the impedance response functions. We show that audio-magnetotelluric processing results depend mainly on the frequency content of electromagnetic waves observed in processed time-series, with an emphasis on the difference between morning and afternoon acquisition. Our new methodology based on the time-frequency signature of lightning-induced electromagnetic waves allows automatic detection and characterization of events in audio

Study of Cancelled Elective Surgical Operations

Directory of Open Access Journals (Sweden)

M Amrollahi

2004-07-01

Full Text Available Introduction: Cancellation of an elective operation is a very important problem, which is the cause for different types of stresses for patients and their families and results in loss of significant amount of time, money and hospital resources. Therefore, finding the main causes of operation postponement may help us to understand and reduce these problems. Material & Method: A special questionnaire was designed to gather information about different causes of operation cancellation and filled from October 23rd (Aban 1st till November 21st (Azar 30 th, 2001 (1380 in all of the teaching hospitals of Yazd university. (S.Dr Rahnemoon, Afshar, Rah Ahan, Bahman and Savaneg Sukhteghy Results were statistically evaluated.. Results: 180 of the 31437 scheduled operations had been cancelled (12.52% Majority of cases (33.3% had been cancelled due to the absence of the surgeons. This group ((Surgeons absent was the most common cause for the postponement of operations (36.7%. The secondary cause of cancellations was related to anesthetic team and operating room problems (25%, the patient’s reasons for cancellation was 16.2% and the most minimal cause of cancellation was insufficient hospital revenue (0.5%. The basis of disease or high risk patients for operation were the main causes of dysfunction of the anesthetic team (68.9% and also the first cause of cancellation. The rate of cancellation was the most in the "older than 60 years" age group. (15.4% The cancellation in women was 12.6% and in males 12.5%. Conclusion: Surgeons schedule more patients keeping in mind cancellations which occur regularly due to patients, hospital, anesthesia, and operating room problems. This over scheduling is a problem itself, so preadmission evaluation clinics are recommended to decrease the rate of cancellations thereby saving the socioeconomic resources and decreasing patient’s stress.

Tissue Cancellation in Dual Energy Mammography Using a Calibration Phantom Customized for Direct Mapping.

Science.gov (United States)

Han, Seokmin; Kang, Dong-Goo

2014-01-01

An easily implementable tissue cancellation method for dual energy mammography is proposed to reduce anatomical noise and enhance lesion visibility. For dual energy calibration, the images of an imaging object are directly mapped onto the images of a customized calibration phantom. Each pixel pair of the low and high energy images of the imaging object was compared to pixel pairs of the low and high energy images of the calibration phantom. The correspondence was measured by absolute difference between the pixel values of imaged object and those of the calibration phantom. Then the closest pixel pair of the calibration phantom images is marked and selected. After the calibration using direct mapping, the regions with lesion yielded different thickness from the background tissues. Taking advantage of the different thickness, the visibility of cancerous lesions was enhanced with increased contrast-to-noise ratio, depending on the size of lesion and breast thickness. However, some tissues near the edge of imaged object still remained after tissue cancellation. These remaining residuals seem to occur due to the heel effect, scattering, nonparallel X-ray beam geometry and Poisson distribution of photons. To improve its performance further, scattering and the heel effect should be compensated.

Public bike sharing in New York City: helmet use behavior patterns at 25 Citi Bike™ stations.

Science.gov (United States)

Basch, Corey H; Ethan, Danna; Zybert, Patricia; Afzaal, Sarah; Spillane, Michael; Basch, Charles E

2015-06-01

Urban public bicycle sharing programs are on the rise in the United States. Launched in 2013, NYC's public bicycle share program, Citi Bike™ is the fastest growing program of its kind in the nation, with nearly 100,000 members and more than 330 docking stations across Manhattan and Brooklyn. The purpose of this study was to assess helmet use behavior among Citi Bike™ riders at 25 of the busiest docking stations. The 25 Citi Bike™ Stations varied greatly in terms of usage: total number of cyclists (N = 96-342), commute versus recreation (22.9-79.5% commute time riders), weekday versus weekend (6.0-49.0% weekend riders). Helmet use ranged between 2.9 and 29.2% across sites (median = 7.5 %). A total of 4,919 cyclists were observed, of whom 545 (11.1%) were wearing helmets. Incoming cyclists were more likely to wear helmets than outgoing cyclists (11.0 vs 5.9%, p = .000). NYC's bike share program endorses helmet use, but relies on education to encourage it. Our data confirm that, to date, this strategy has not been successful.

Surgery cancellations at a public hospital

Directory of Open Access Journals (Sweden)

Erika Pittelkow

2008-12-01

Full Text Available Objective: To determine the frequency of cancellation of scheduledsurgeries at a public hospital in the city of São Paulo, and to identifythe reasons of cancellation. Methods: A descriptive, exploratory,retrospective study, with quantitative analysis, of records ofprocedures cancelled and medical charts of patients whose surgerieswere cancelled, between January 2006 and July 2007. Results: Ofthe 6,149 (100% surgeries scheduled for the period surveyed, 701(11.4% were canceled and 5,448 (88.6% conducted; among thesurgeries cancelled, most were general surgeries (237/33.8% andorthopedic surgery (200/28.5%; surgeons or assistant surgeons(518/73.9% and anesthesiologists (183/26.1% were responsible forcancellations. The primary reasons for cancellation were unfavorableclinical status of patients (225/32.1%, no show up of patients(119/17.0%, change in medical management (79/11.3%, patientnot appropriately prepared (53/7.5% and lack of material (52/7.4%.Conclusions: This study enabled identifying the frequency and causesof surgical cancellations at a public hospital, so as to contribute toimproving professional performance in this area.

Modeling Audio Fingerprints : Structure, Distortion, Capacity

NARCIS (Netherlands)

Doets, P.J.O.

2010-01-01

An audio fingerprint is a compact low-level representation of a multimedia signal. An audio fingerprint can be used to identify audio files or fragments in a reliable way. The use of audio fingerprints for identification consists of two phases. In the enrollment phase known content is fingerprinted,

Towards reducing impact-induced brain injury: lessons from a computational study of army and football helmet pads.

Science.gov (United States)

Moss, William C; King, Michael J; Blackman, Eric G

2014-01-01

We use computational simulations to compare the impact response of different football and U.S. Army helmet pad materials. We conduct experiments to characterise the material response of different helmet pads. We simulate experimental helmet impact tests performed by the U.S. Army to validate our methods. We then simulate a cylindrical impactor striking different pads. The acceleration history of the impactor is used to calculate the head injury criterion for each pad. We conduct sensitivity studies exploring the effects of pad composition, geometry and material stiffness. We find that (1) the football pad materials do not outperform the currently used military pad material in militarily relevant impact scenarios; (2) optimal material properties for a pad depend on impact energy and (3) thicker pads perform better at all velocities. Although we considered only the isolated response of pad materials, not entire helmet systems, our analysis suggests that by using larger helmet shells with correspondingly thicker pads, impact-induced traumatic brain injury may be reduced.

20 CFR 217.27 - Effect of cancellation.

Science.gov (United States)

2010-04-01

... ANNUITY OR LUMP SUM Cancellation of Application § 217.27 Effect of cancellation. When a person cancels an application the effect is the same as though an application was never filed. When an employee cancels his or her application, any application filed by the employee's spouse is also cancelled. However, a request...

Applying the health action process approach to bicycle helmet use and evaluating a social marketing campaign.

Science.gov (United States)

Karl, Florian M; Smith, Jennifer; Piedt, Shannon; Turcotte, Kate; Pike, Ian

2017-08-05

Bicycle injuries are of concern in Canada. Since helmet use was mandated in 1996 in the province of British Columbia, Canada, use has increased and head injuries have decreased. Despite the law, many cyclists do not wear a helmet. Health action process approach (HAPA) model explains intention and behaviour with self-efficacy, risk perception, outcome expectancies and planning constructs. The present study examines the impact of a social marketing campaign on HAPA constructs in the context of bicycle helmet use. A questionnaire was administered to identify factors determining helmet use. Intention to obey the law, and perceived risk of being caught if not obeying the law were included as additional constructs. Path analysis was used to extract the strongest influences on intention and behaviour. The social marketing campaign was evaluated through t-test comparisons after propensity score matching and generalised linear modelling (GLM) were applied to adjust for the same covariates. 400 cyclists aged 25-54 years completed the questionnaire. Self-efficacy and Intention were most predictive of intention to wear a helmet, which, moderated by planning, strongly predicted behaviour. Perceived risk and outcome expectancies had no significant impact on intention. GLM showed that exposure to the campaign was significantly associated with higher values in self-efficacy, intention and bicycle helmet use. Self-efficacy and planning are important points of action for promoting helmet use. Social marketing campaigns that remind people of appropriate preventive action have an impact on behaviour. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Laminated helmet materials characterization by terahertz kinetics spectroscopy

Science.gov (United States)

Rahman, Anis; Rahman, Aunik K.

2015-05-01

High speed acquisition of reflected terahertz energy constitutes a kinetics spectrum that is an effective tool for layered materials' deformation characterization under ballistic impact. Here we describe utilizing the kinetics spectrum for quantifying a deformation event due to impact in material used for Soldier's helmet. The same technique may be utilized for real-time assessment of trauma by measuring the helmet wore by athletes. The deformation of a laminated material (e.g., a helmet) is dependent on the nature of impact and projectile; thus can uniquely characterize the impact condition leading to a diagnostic procedure based on the energy received by an athlete during an impact. We outline the calibration process for a given material under ballistic impact and then utilize the calibration for extracting physical parameters from the measured kinetics spectrum. Measured kinetics spectra are used to outline the method and rationale for extending the concept to a diagnosis tool. In particular, captured kinetics spectra from multilayered plates subjected to ballistic hit under experimental conditions by high speed digital acquisition system. An algorithm was devised to extract deformation and deformation velocity from which the energy received on the skull was estimated via laws of nonrelativistic motion. This energy is assumed to be related to actual injury conditions, thus forming a basis for determining whether the hit would cause concussion, trauma, or stigma. Such quantification may be used for diagnosing a Soldier's trauma condition in the field or that of an athlete's.

Introduction to audio analysis a MATLAB approach

CERN Document Server

Giannakopoulos, Theodoros

2014-01-01

Introduction to Audio Analysis serves as a standalone introduction to audio analysis, providing theoretical background to many state-of-the-art techniques. It covers the essential theory necessary to develop audio engineering applications, but also uses programming techniques, notably MATLAB®, to take a more applied approach to the topic. Basic theory and reproducible experiments are combined to demonstrate theoretical concepts from a practical point of view and provide a solid foundation in the field of audio analysis. Audio feature extraction, audio classification, audio segmentation, au

A new Monte Carlo method for neutron noise calculations in the frequency domain

International Nuclear Information System (INIS)

Rouchon, Amélie; Zoia, Andrea; Sanchez, Richard

2017-01-01

Neutron noise equations, which are obtained by assuming small perturbations of macroscopic cross sections around a steady-state neutron field and by subsequently taking the Fourier transform in the frequency domain, have been usually solved by analytical techniques or by resorting to diffusion theory. A stochastic approach has been recently proposed in the literature by using particles with complex-valued weights and by applying a weight cancellation technique. We develop a new Monte Carlo algorithm that solves the transport neutron noise equations in the frequency domain. The stochastic method presented here relies on a modified collision operator and does not need any weight cancellation technique. In this paper, both Monte Carlo methods are compared with deterministic methods (diffusion in a slab geometry and transport in a simplified rod model) for several noise frequencies and for isotropic and anisotropic noise sources. Our stochastic method shows better performances in the frequency region of interest and is easier to implement because it relies upon the conventional algorithm for fixed-source problems.

Advances in audio source seperation and multisource audio content retrieval

Science.gov (United States)

Vincent, Emmanuel

2012-06-01

Audio source separation aims to extract the signals of individual sound sources from a given recording. In this paper, we review three recent advances which improve the robustness of source separation in real-world challenging scenarios and enable its use for multisource content retrieval tasks, such as automatic speech recognition (ASR) or acoustic event detection (AED) in noisy environments. We present a Flexible Audio Source Separation Toolkit (FASST) and discuss its advantages compared to earlier approaches such as independent component analysis (ICA) and sparse component analysis (SCA). We explain how cues as diverse as harmonicity, spectral envelope, temporal fine structure or spatial location can be jointly exploited by this toolkit. We subsequently present the uncertainty decoding (UD) framework for the integration of audio source separation and audio content retrieval. We show how the uncertainty about the separated source signals can be accurately estimated and propagated to the features. Finally, we explain how this uncertainty can be efficiently exploited by a classifier, both at the training and the decoding stage. We illustrate the resulting performance improvements in terms of speech separation quality and speaker recognition accuracy.

The formulation and implementation of a national helmet law: a case study from Viet Nam.

Science.gov (United States)

Passmore, Jonathon W; Nguyen, Lan Huong; Nguyen, Nam Phuong; Olivé, Jean-Marc

2010-10-01

Road traffic injuries are a leading cause of death and disability in Viet Nam. In 2008, official data reported 11 243 deaths and 7771 serious injuries on the roads, of which an estimated 60% of fatalities occur in motorcycle riders and passengers. In recognition of this problem, Viet Nam has had partial motorcycle helmet legislation since 1995. However, for a variety of reasons, implementation and enforcement have been limited. On 15 December 2007, Viet Nam's first comprehensive mandatory helmet law came into effect, covering all riders and passengers on all roads nationwide. Penalties increased ten-fold and cohorts of police were mobilized for enforcement. The Viet Nam national helmet legislation was developed and implemented by the National Traffic Safety Committee. Despite past barriers to enforcement, increased policing in 2008 led to 680 000 infringements being issued for non-helmet wearing. While changes in helmet wearing were not nationally observed, significant increases were documented in selected provinces in the first six months of the law's introduction. In Da Nang, helmet wearing increased from 27 to 99%. In the first three months after the law took effect, surveillance data from 20 urban and rural hospitals, found the risk of road traffic head injuries and deaths decreased by 16% and 18% respectively. Political leadership, intensive advanced public education and stringent enforcement have contributed to the successful implementation of the new law. Through continual monitoring of the legislation, loopholes detrimental to the effectiveness of the law have been identified and addressed.

An Adaptive Filter for the Removal of Drifting Sinusoidal Noise Without a Reference.

Science.gov (United States)

Kelly, John W; Siewiorek, Daniel P; Smailagic, Asim; Wang, Wei

2016-01-01

This paper presents a method for filtering sinusoidal noise with a variable bandwidth filter that is capable of tracking a sinusoid's drifting frequency. The method, which is based on the adaptive noise canceling (ANC) technique, will be referred to here as the adaptive sinusoid canceler (ASC). The ASC eliminates sinusoidal contamination by tracking its frequency and achieving a narrower bandwidth than typical notch filters. The detected frequency is used to digitally generate an internal reference instead of relying on an external one as ANC filters typically do. The filter's bandwidth adjusts to achieve faster and more accurate convergence. In this paper, the focus of the discussion and the data is physiological signals, specifically electrocorticographic (ECoG) neural data contaminated with power line noise, but the presented technique could be applicable to other recordings as well. On simulated data, the ASC was able to reliably track the noise's frequency, properly adjust its bandwidth, and outperform comparative methods including standard notch filters and an adaptive line enhancer. These results were reinforced by visual results obtained from real ECoG data. The ASC showed that it could be an effective method for increasing signal to noise ratio in the presence of drifting sinusoidal noise, which is of significant interest for biomedical applications.

An Adaptive Noise Cancellation System Based on Linear and Widely Linear Complex Valued Least Mean Square Algorithms for Removing Electrooculography Artifacts from Electroencephalography Signals

Directory of Open Access Journals (Sweden)

Engin Cemal MENGÜÇ

2018-03-01

Full Text Available In this study, an adaptive noise cancellation (ANC system based on linear and widely linear (WL complex valued least mean square (LMS algorithms is designed for removing electrooculography (EOG artifacts from electroencephalography (EEG signals. The real valued EOG and EEG signals (Fp1 and Fp2 given in dataset are primarily expressed as a complex valued signal in the complex domain. Then, using the proposed ANC system, the EOG artifacts are eliminated in the complex domain from the EEG signals. Expression of these signals in the complex domain allows us to remove EOG artifacts from two EEG channels simultaneously. Moreover, in this study, it has been shown that the complex valued EEG signal exhibits noncircular behavior, and in the case, the WL-CLMS algorithm enhances the performance of the ANC system compared to real-valued LMS and CLMS algorithms. Simulation results support the proposed approach.

Regression of environmental noise in LIGO data

International Nuclear Information System (INIS)

Tiwari, V; Klimenko, S; Mitselmakher, G; Necula, V; Drago, M; Prodi, G; Frolov, V; Yakushin, I; Re, V; Salemi, F; Vedovato, G

2015-01-01

We address the problem of noise regression in the output of gravitational-wave (GW) interferometers, using data from the physical environmental monitors (PEM). The objective of the regression analysis is to predict environmental noise in the GW channel from the PEM measurements. One of the most promising regression methods is based on the construction of Wiener–Kolmogorov (WK) filters. Using this method, the seismic noise cancellation from the LIGO GW channel has already been performed. In the presented approach the WK method has been extended, incorporating banks of Wiener filters in the time–frequency domain, multi-channel analysis and regulation schemes, which greatly enhance the versatility of the regression analysis. Also we present the first results on regression of the bi-coherent noise in the LIGO data. (paper)

48 CFR 552.238-73 - Cancellation.

Science.gov (United States)

2010-10-01

... may cancel this contract in whole or in part by providing written notice. The cancellation will take... elects to cancel this contract, the Government will not reimburse the minimum guarantee. (End of clause) ...

Roundtable Audio Discussion

Directory of Open Access Journals (Sweden)

Chris Bigum

2007-01-01

Full Text Available RoundTable on Technology, Teaching and Tools. This is a roundtable audio interview conducted by James Farmer, founder of Edublogs, with Anne Bartlett-Bragg (University of Technology Sydney and Chris Bigum (Deakin University. Skype was used to make and record the audio conference and the resulting sound file was edited by Andrew McLauchlan.

The Influence of Various Factors on High School Football Helmet Face Mask Removal: A Retrospective, Cross-Sectional Analysis

Science.gov (United States)

Swartz, Erik E; Decoster, Laura C; Norkus, Susan A; Cappaert, Thomas A

2007-01-01

Context: Most research on face mask removal has been performed on unused equipment. Objective: To identify and compare factors that influence the condition of helmet components and their relationship to face mask removal. Design: A cross-sectional, retrospective study. Setting: Five athletic equipment reconditioning/recertification facilities. Participants: 2584 helmets from 46 high school football teams representing 5 geographic regions. Intervention(s): Helmet characteristics (brand, model, hardware components) were recorded. Helmets were mounted and face mask removal was attempted using a cordless screwdriver. The 2004 season profiles and weather histories were obtained for each high school. Main Outcome Measure(s): Success and failure (including reason) for removal of 4 screws from the face mask were noted. Failure rates among regions, teams, reconditioning year, and screw color (type) were compared. Weather histories were compared. We conducted a discriminant analysis to determine if weather variables, region, helmet brand and model, reconditioning year, and screw color could predict successful face mask removal. Metallurgic analysis of screw samples was performed. Results: All screws were successfully removed from 2165 (84%) helmets. At least 1 screw could not be removed from 419 (16%) helmets. Significant differences were found for mean screw failure per helmet among the 5 regions, with the Midwest having the lowest failure rate (0.08 ± 0.38) and the Southern (0.33 ± 0.72), the highest. Differences were found in screw failure rates among the 46 teams (F1,45 = 9.4, P < .01). Helmets with the longest interval since last reconditioning (3 years) had the highest failure rate, 0.47 ± 0.93. Differences in success rates were found among 4 screw types (χ21,4 = 647, P < .01), with silver screws having the lowest percentage of failures (3.4%). A discriminant analysis (Λ = .932, χ214,n=2584 = 175.34, P < .001) revealed screw type to be the strongest predictor of

Elevated Extravascular Lung Water Index (ELWI) as a Predictor of Failure of Continuous Positive Airway Pressure Via Helmet (Helmet-CPAP) in Patients With Acute Respiratory Failure After Major Surgery.

Science.gov (United States)

Redondo Calvo, Francisco Javier; Bejarano Ramirez, Natalia; Uña Orejon, Rafael; Villazala Garcia, Ruben; Yuste Peña, Ana Sofia; Belda, Francisco Javier

2015-11-01

NIV is increasingly used for prevention and treatment of respiratory complications and failure. Some of them are admitted to the PACU with advanced hemodynamic monitors which allow quantification of Extravascular Lung Water (EVLW) by transpulmonary thermodilution technique (TPTD) and Pulmonary Vascular Permeability (PVP) providing information on lung edema. The objective of this study was to ascertain if EVLW Index and PVP Index may predict failure (intubation) or success (non-intubation) in patients developing acute respiratory failure (ARF) in the postoperative period following major abdominal surgery, where the first line of treatment was non-invasive continuous positive airway pressure via a helmet. Hemodynamic variables, EVLWI and PVPI were monitored with a transpulmonary thermodilution hemodynamic monitor device (PiCCO™) before and after the application of CPAP. Avoidance of intubation was observed in 66% of patients with Helmet-CPAP. In these patients after the first hour of application of CPAP, PaO2/FiO2 ratio significantly increased (303.33±65.2 vs. 141.6±14.6, P<.01). Before starting Helmet-CPAP values of EVLWI and PVPI were significantly lower in non-intubated patients (EVLWI 8.6±1.08 vs. 11.8±0.99ml/kg IBW, P<.01 and PVPI 1.7±0.56 vs. 3.0±0.88, P<.01). An optimal cut-off value for EVLWI was established at 9.5, and at 2.45 for PVPI (sensitivity of 0.7; specificity of 0.9, P<.01). In this type of patient the physiological parameters that predict the failure of Helmet-CPAP with the greatest accuracy were the value of the EVLWI and PVPI before Helmet-CPAP institution and the PaO2/FiO2 ratio and the respiratory rate after one hour of CPAP. Copyright © 2014 SEPAR. Published by Elsevier Espana. All rights reserved.

Brain response to primary blast wave using validated finite element models of human head and advanced combat helmet

Directory of Open Access Journals (Sweden)

Liying eZhang

2013-08-01

Full Text Available Blast-induced traumatic brain injury has emerged as a signature injury in combat casualty care. Present combat helmets are designed primarily to protect against ballistic and blunt impacts, but the current issue with helmets is protection concerning blasts. In order to delineate the blast wave attenuating capability of the Advanced Combat Helmet (ACH, a finite element (FE study was undertaken to evaluate the head response against blast loadings with and without helmet using a partially validated FE model of the human head and ACH. Four levels of overpressures (0.27-0.66 MPa from the Bowen’s lung iso-damage threshold curves were used to simulate blast insults. Effectiveness of the helmet with respect to head orientation was also investigated. The resulting biomechanical responses of the brain to blast threats were compared for human head with and without the helmet. For all Bowen’s cases, the peak intracranial pressures (ICP in the head ranged from 0.68-1.8 MPa in the coup cortical region. ACH was found to mitigate ICP in the head by 10-35%. Helmeted head resulted in 30% lower average peak brain strains and product of strain and strain rate. Among three blast loading directions with ACH, highest reduction in peak ICP (44% was due to backward blasts whereas the lowest reduction in peak ICP and brain strains was due to forward blast (27%. The biomechanical responses of a human head to primary blast insult exhibited directional sensitivity owing to the different geometry contours and coverage of the helmet construction and asymmetric anatomy of the head. Thus, direction-specific tolerances are needed in helmet design in order to offer omni-directional protection for the human head. The blasts of varying peak overpressures and durations that are believed to produce the same level of lung injury produce different levels of mechanical responses in the brain, and hence "iso-damage" curves for brain injury are likely different than the Bowen curves

Beamspace Adaptive Beamforming for Hydrodynamic Towed Array Self-Noise Cancellation

National Research Council Canada - National Science Library

Premus, Vincent

2001-01-01

... against signal self-nulling associated with steering vector mismatch. Particular attention is paid to the definition of white noise gain as the metric that reflects the level of mainlobe adaptive nulling for an adaptive beamformer...

Beamspace Adaptive Beamforming for Hydrodynamic Towed Array Self-Noise Cancellation

National Research Council Canada - National Science Library

Premus, Vincent

2000-01-01

... against signal self-nulling associated with steering vector mismatch. Particular attention is paid to the definition of white noise gain as the metric that reflects the level of mainlobe adaptive nulling for an adaptive beamformer...

Impact of Helmet Use on Severity of Epidural Hematomas in Cambodia.

Science.gov (United States)

Gupta, Saksham; Iv, Vycheth; Sam, Nang; Vuthy, Din; Klaric, Katherine; Shrime, Mark G; Park, Kee B

2017-04-01

Traumatic brain injury is a major cause of morbidity and mortality worldwide, often necessitating neurosurgical intervention to evacuate intracranial bleeding. Since the early 2000s, Cambodia has been undergoing a rapid increase in motorcycle transit and in road traffic accidents, but the prevalence of helmet usage remains low. Epidural hematomas are severe traumatic brain injuries that can necessitate neurosurgical intervention. This is a retrospective cohort study of patients with epidural hematoma secondary to motorcycle accidents who presented to a major national tertiary care center in Phnom Penh, Cambodia, between November 2013 and March 2016. All patients were diagnosed with computed tomography of the head. In this cohort, 21.6% of patients in motorcycle accidents presented with epidural hematoma and 89.1% of patients were men, 47.6% were intoxicated, and were 87.8% were not wearing helmets at the moment of impact. Not wearing a helmet was associated with a 6.90-fold increase in odds of presenting with a moderate-to-severe Glasgow coma scale score and a 3.76-fold increase in odds of requiring craniotomy or craniectomy for evacuation of hematoma. Male sex was also associated with increased odds of higher clinical severity at presentation and indication for craniotomy or craniectomy, and alcohol intoxication at the time of accident was not associated with either. Helmet usage is protective in reducing the severity of presentation and need for neurosurgical intervention for patients with epidural hematoma secondary to motorcycle accidents. Copyright © 2016 Elsevier Inc. All rights reserved.

The physiological demands of horseback mustering when wearing an equestrian helmet.

Science.gov (United States)

Taylor, Nigel A S; Caldwell, Joanne N; Dyer, Rodd

2008-09-01

The hottest months on northern Australian cattle stations are from September to November, and it is during these months that horseback cattle mustering occurs. Stockmen wear clothing that restricts heat loss, and protective helmets have recently been introduced. Anecdotal evidence points to the possibility that helmets may increase the probability of developing heat illness, or reducing workplace performance. In this project, we quantified the working (thermal) environment on such cattle stations, and measured the metabolic demands on, and concurrent physiological strain in stockmen during mustering, whilst wearing an equestrian helmet. During horseback work, the average heart rate was 102.0 beats min(-1) (SD 14.0), with almost 90% of the time (238 min) spent working at intensities <50% of the heart rate reserve. The projected metabolic heat production during mustering ranged between 178 and 333 W (women), and between 212 and 542 W (men). The average core temperature was 37.6 degrees C, while the mean skin temperature averaged 34.1 degrees C. It was concluded that the working environment is, on average, thermally uncompensable during the mustering season. However, horseback mustering per se is a relatively low-intensity activity, interspersed with short periods of high-intensity work. This activity level was reflected within core temperatures, which rarely climbed above values associated with light-moderate exercise. Thus, whilst the climatic state was uncompensable, stockmen used behavioural strategies to minimise the risk of heat illness. Finally, it was observed that the helmet, though unpleasant to wear, did not appear to increase thermal strain in a manner that would disadvantage stockmen.

IIR digital filter design for powerline noise cancellation of ECG signal using arduino platform

Science.gov (United States)

Rahmatillah, Akif; Ataulkarim

2017-05-01

Powerline noise has been one of significant noises of Electrocardiogram (ECG) signal measurement. This noise is characterized by a sinusoidal signal which has 50 Hz of noise and 0.3 mV of maximum amplitude. This paper describes the design of IIR Notch filter design to reject a 50 Hz power line noise. IIR filter coefficients were calculated using pole placement method with three variations of band stop cut off frequencies of (49-51)Hz, (48 - 52)Hz, and (47 - 53)Hz. The algorithm and coefficients of filter were embedded to Arduino DUE (ARM 32 bit microcontroller). IIR notch filter designed has been able to reject power line noise with average square of error value of 0.225 on (49-51) Hz filter design and 0.2831 on (48 - 52)Hz filter design.

The burden of motorcycle-related neuro-trauma in Ireland and associated helmet usage.

LENUS (Irish Health Repository)

Murphy, R K J

2009-04-01

Motorcycles represent less than 2% of the licensed vehicles but motorcyclists account for 12% of road deaths in Ireland. The British Road Safety Authority has introduced the Sharp programme, which hopes to save 50 lives in the U.K. each year alone by helping riders to choose the best-fitting and safest helmets. We evaluated the pattern of head injuries sustained by motorcyclists referred to the two neurosurgical centres Beaumont Hospital and Cork University Hospital in Ireland and ascertained if the new SHARP guidelines could be of benefit in reducing the burden of motorcycle related neurotrauma and disability in Ireland. Despite Ireland having mandatory helmet laws almost a quarter of our motorcyclists with traumatic brain injury were unhelmeted. A significant reduction in mortality and morbidity is predicted if all motorcyclists in Ireland were to wear helmets that satisfied the SHARP criteria.

Could Audio-Described Films Benefit from Audio Introductions? An Audience Response Study

Science.gov (United States)

Romero-Fresco, Pablo; Fryer, Louise

2013-01-01

Introduction: Time constraints limit the quantity and type of information conveyed in audio description (AD) for films, in particular the cinematic aspects. Inspired by introductory notes for theatre AD, this study developed audio introductions (AIs) for "Slumdog Millionaire" and "Man on Wire." Each AI comprised 10 minutes of…

A Method to Detect AAC Audio Forgery

Directory of Open Access Journals (Sweden)

Qingzhong Liu

2015-08-01

Full Text Available Advanced Audio Coding (AAC, a standardized lossy compression scheme for digital audio, which was designed to be the successor of the MP3 format, generally achieves better sound quality than MP3 at similar bit rates. While AAC is also the default or standard audio format for many devices and AAC audio files may be presented as important digital evidences, the authentication of the audio files is highly needed but relatively missing. In this paper, we propose a scheme to expose tampered AAC audio streams that are encoded at the same encoding bit-rate. Specifically, we design a shift-recompression based method to retrieve the differential features between the re-encoded audio stream at each shifting and original audio stream, learning classifier is employed to recognize different patterns of differential features of the doctored forgery files and original (untouched audio files. Experimental results show that our approach is very promising and effective to detect the forgery of the same encoding bit-rate on AAC audio streams. Our study also shows that shift recompression-based differential analysis is very effective for detection of the MP3 forgery at the same bit rate.

Wideband CMOS low noise amplifier including an active balun

NARCIS (Netherlands)

Blaakmeer, S.C.; Klumperink, Eric A.M.; Leenaerts, D.M.W.; Nauta, Bram

2007-01-01

An inductorless LNA with active balun is proposed for multi-standard radio applications between 100MHz and 6GHz [1]. It exploits a combination of a common-gate (CG) stage and an common-source (CS) stage with replica biasing to maximize balanced operation, while simultaneously canceling the noise and

Location audio simplified capturing your audio and your audience

CERN Document Server

Miles, Dean

2014-01-01

From the basics of using camera, handheld, lavalier, and shotgun microphones to camera calibration and mixer set-ups, Location Audio Simplified unlocks the secrets to clean and clear broadcast quality audio no matter what challenges you face. Author Dean Miles applies his twenty-plus years of experience as a professional location operator to teach the skills, techniques, tips, and secrets needed to produce high-quality production sound on location. Humorous and thoroughly practical, the book covers a wide array of topics, such as:* location selection* field mixing* boo

Smartphone audio port data collection cookbook

Directory of Open Access Journals (Sweden)

Kyle Forinash

2018-06-01

Full Text Available The audio port of a smartphone is designed to send and receive audio but can be harnessed for portable, economical, and accurate data collection from a variety of sources. While smartphones have internal sensors to measure a number of physical phenomena such as acceleration, magnetism and illumination levels, measurement of other phenomena such as voltage, external temperature, or accurate timing of moving objects are excluded. The audio port cannot be only employed to sense external phenomena. It has the additional advantage of timing precision; because audio is recorded or played at a controlled rate separated from other smartphone activities, timings based on audio can be highly accurate. The following outlines unpublished details of the audio port technical elements for data collection, a general data collection recipe and an example timing application for Android devices.

Self-Powered Safety Helmet Based on Hybridized Nanogenerator for Emergency.

Science.gov (United States)

Jin, Long; Chen, Jun; Zhang, Binbin; Deng, Weili; Zhang, Lei; Zhang, Haitao; Huang, Xi; Zhu, Minhao; Yang, Weiqing; Wang, Zhong Lin

2016-08-23

The rapid development of Internet of Things and the related sensor technology requires sustainable power sources for their continuous operation. Scavenging and utilizing the ambient environmental energy could be a superior solution. Here, we report a self-powered helmet for emergency, which was powered by the energy converted from ambient mechanical vibration via a hybridized nanogenerator that consists of a triboelectric nanogenerator (TENG) and an electromagnetic generator (EMG). Integrating with transformers and rectifiers, the hybridized nanogenerator can deliver a power density up to 167.22 W/m(3), which was demonstrated to light up 1000 commercial light-emitting diodes (LEDs) instantaneously. By wearing the developed safety helmet, equipped with rationally designed hybridized nanogenerator, the harvested vibration energy from natural human motion is also capable of powering a wireless pedometer for real-time transmitting data reporting to a personal cell phone. Without adding much extra weight to a commercial one, the developed wearing helmet can be a superior sustainable power source for explorers, engineers, mine-workers under well, as well as and disaster-relief workers, especially in remote areas. This work not only presents a significant step toward energy harvesting from human biomechanical movement, but also greatly expands the applicability of TENGs as power sources for self-sustained electronics.

Continuous positive airway pressure with helmet versus mask in infants with bronchiolitis: an RCT.

Science.gov (United States)

Chidini, Giovanna; Piastra, Marco; Marchesi, Tiziana; De Luca, Daniele; Napolitano, Luisa; Salvo, Ida; Wolfler, Andrea; Pelosi, Paolo; Damasco, Mirco; Conti, Giorgio; Calderini, Edoardo

2015-04-01

Noninvasive continuous positive airway pressure (CPAP) is usually applied with a nasal or facial mask to treat mild acute respiratory failure (ARF) in infants. A pediatric helmet has now been introduced in clinical practice to deliver CPAP. This study compared treatment failure rates during CPAP delivered by helmet or facial mask in infants with respiratory syncytial virus-induced ARF. In this multicenter randomized controlled trial, 30 infants with respiratory syncytial virus-induced ARF were randomized to receive CPAP by helmet (n = 17) or facial mask (n = 13). The primary endpoint was treatment failure rate (defined as due to intolerance or need for intubation). Secondary outcomes were CPAP application time, number of patients requiring sedation, and complications with each interface. Compared with the facial mask, CPAP by helmet had a lower treatment failure rate due to intolerance (3/17 [17%] vs 7/13 [54%], P = .009), and fewer infants required sedation (6/17 [35%] vs 13/13 [100%], P = .023); the intubation rates were similar. In successfully treated patients, CPAP resulted in better gas exchange and breathing pattern with both interfaces. No major complications due to the interfaces occurred, but CPAP by mask had higher rates of cutaneous sores and leaks. These findings confirm that CPAP delivered by helmet is better tolerated than CPAP delivered by facial mask and requires less sedation. In addition, it is safe to use and free from adverse events, even in a prolonged clinical setting. Copyright © 2015 by the American Academy of Pediatrics.

Structure Learning in Audio

DEFF Research Database (Denmark)

Nielsen, Andreas Brinch

By having information about the setting a user is in, a computer is able to make decisions proactively to facilitate tasks for the user. Two approaches are taken in this thesis to achieve more information about an audio environment. One approach is that of classifying audio, and a new approach...... investigated. A fast and computationally simple approach that compares recordings and classifies if they are from the same audio environment have been developed, and shows very high accuracy and the ability to synchronize recordings in the case of recording devices which are not connected. A more general model...

The Ability of American Football Helmets to Manage Linear Acceleration With Repeated High-Energy Impacts.

Science.gov (United States)

Cournoyer, Janie; Post, Andrew; Rousseau, Philippe; Hoshizaki, Blaine

2016-03-01

Football players can receive up to 1400 head impacts per season, averaging 6.3 impacts per practice and 14.3 impacts per game. A decrease in the capacity of a helmet to manage linear acceleration with multiple impacts could increase the risk of traumatic brain injury. To investigate the ability of football helmets to manage linear acceleration with multiple high-energy impacts. Descriptive laboratory study. Laboratory. We collected linear-acceleration data for 100 impacts at 6 locations on 4 helmets of different models currently used in football. Impacts 11 to 20 were compared with impacts 91 to 100 for each of the 6 locations. Linear acceleration was greater after multiple impacts (91-100) than after the first few impacts (11-20) for the front, front-boss, rear, and top locations. However, these differences are not clinically relevant as they do not affect the risk for head injury. American football helmet performance deteriorated with multiple impacts, but this is unlikely to be a factor in head-injury causation during a game or over a season.

The Cyclists Helmet Study in Juba, Southern Sudan, 2006

African Journals Online (AJOL)

Ann Burgess

Juba has a poor road network and few public transport options, with an increasing number of people riding ... The conclusion is that cyclists need information on the importance of wearing a helmet. ... Leading safety advocates recommend the.

A multichannel nonlinear adaptive noise canceller based on generalized FLANN for fetal ECG extraction

International Nuclear Information System (INIS)

Ma, Yaping; Wei, Guo; Sun, Jinwei; Xiao, Yegui

2016-01-01

In this paper, a multichannel nonlinear adaptive noise canceller (ANC) based on the generalized functional link artificial neural network (FLANN, GFLANN) is proposed for fetal electrocardiogram (FECG) extraction. A FIR filter and a GFLANN are equipped in parallel in each reference channel to respectively approximate the linearity and nonlinearity between the maternal ECG (MECG) and the composite abdominal ECG (AECG). A fast scheme is also introduced to reduce the computational cost of the FLANN and the GFLANN. Two (2) sets of ECG time sequences, one synthetic and one real, are utilized to demonstrate the improved effectiveness of the proposed nonlinear ANC. The real dataset is derived from the Physionet non-invasive FECG database (PNIFECGDB) including 55 multichannel recordings taken from a pregnant woman. It contains two subdatasets that consist of 14 and 8 recordings, respectively, with each recording being 90 s long. Simulation results based on these two datasets reveal, on the whole, that the proposed ANC does enjoy higher capability to deal with nonlinearity between MECG and AECG as compared with previous ANCs in terms of fetal QRS (FQRS)-related statistics and morphology of the extracted FECG waveforms. In particular, for the second real subdataset, the F1-measure results produced by the PCA-based template subtraction (TS pca ) technique and six (6) single-reference channel ANCs using LMS- and RLS-based FIR filters, Volterra filter, FLANN, GFLANN, and adaptive echo state neural network (ESN a ) are 92.47%, 93.70%, 94.07%, 94.22%, 94.90%, 94.90%, and 95.46%, respectively. The same F1-measure statistical results from five (5) multi-reference channel ANCs (LMS- and RLS-based FIR filters, Volterra filter, FLANN, and GFLANN) for the second real subdataset turn out to be 94.08%, 94.29%, 94.68%, 94.91%, and 94.96%, respectively. These results indicate that the ESN a and GFLANN perform best, with the ESN a being slightly better than the GFLANN but about four times

34 CFR 674.59 - Cancellation for military service.

Science.gov (United States)

2010-07-01

... 34 Education 3 2010-07-01 2010-07-01 false Cancellation for military service. 674.59 Section 674... Cancellation for military service. (a) Cancellation on a Defense loan. (1) An institution must cancel up to 50... cancellation rate is 121/2 percent of the original loan principal, plus the interest on the unpaid balance...

First Test of Fan Active Noise Control (ANC) Completed

Science.gov (United States)

2005-01-01

With the advent of ultrahigh-bypass engines, the space available for passive acoustic treatment is becoming more limited, whereas noise regulations are becoming more stringent. Active noise control (ANC) holds promise as a solution to this problem. It uses secondary (added) noise sources to reduce or eliminate the offending noise radiation. The first active noise control test on the low-speed fan test bed was a General Electric Company system designed to control either the exhaust or inlet fan tone. This system consists of a "ring source," an induct array of error microphones, and a control computer. Fan tone noise propagates in a duct in the form of spinning waves. These waves are detected by the microphone array, and the computer identifies their spinning structure. The computer then controls the "ring source" to generate waves that have the same spinning structure and amplitude, but 180 out of phase with the fan noise. This computer generated tone cancels the fan tone before it radiates from the duct and is heard in the far field. The "ring source" used in these tests is a cylindrical array of 16 flat-plate acoustic radiators that are driven by thin piezoceramic sheets bonded to their back surfaces. The resulting source can produce spinning waves up to mode 7 at levels high enough to cancel the fan tone. The control software is flexible enough to work on spinning mode orders from -6 to 6. In this test, the fan was configured to produce a tone of order 6. The complete modal (spinning and radial) structure of the tones was measured with two builtin sets of rotating microphone rakes. These rakes provide a measurement of the system performance independent from the control system error microphones. In addition, the far-field noise was measured with a semicircular array of 28 microphones. This test represents the first in a series of tests that demonstrate different active noise control concepts, each on a progressively more complicated modal structure. The tests are

A centralized audio presentation manager

Energy Technology Data Exchange (ETDEWEB)

Papp, A.L. III; Blattner, M.M.

1994-05-16

The centralized audio presentation manager addresses the problems which occur when multiple programs running simultaneously attempt to use the audio output of a computer system. Time dependence of sound means that certain auditory messages must be scheduled simultaneously, which can lead to perceptual problems due to psychoacoustic phenomena. Furthermore, the combination of speech and nonspeech audio is examined; each presents its own problems of perceptibility in an acoustic environment composed of multiple auditory streams. The centralized audio presentation manager receives abstract parameterized message requests from the currently running programs, and attempts to create and present a sonic representation in the most perceptible manner through the use of a theoretically and empirically designed rule set.

Instrumental Landing Using Audio Indication

Science.gov (United States)

Burlak, E. A.; Nabatchikov, A. M.; Korsun, O. N.

2018-02-01

The paper proposes an audio indication method for presenting to a pilot the information regarding the relative positions of an aircraft in the tasks of precision piloting. The implementation of the method is presented, the use of such parameters of audio signal as loudness, frequency and modulation are discussed. To confirm the operability of the audio indication channel the experiments using modern aircraft simulation facility were carried out. The simulated performed the instrument landing using the proposed audio method to indicate the aircraft deviations in relation to the slide path. The results proved compatible with the simulated instrumental landings using the traditional glidescope pointers. It inspires to develop the method in order to solve other precision piloting tasks.

Bit rates in audio source coding

NARCIS (Netherlands)

Veldhuis, Raymond N.J.

1992-01-01

The goal is to introduce and solve the audio coding optimization problem. Psychoacoustic results such as masking and excitation pattern models are combined with results from rate distortion theory to formulate the audio coding optimization problem. The solution of the audio optimization problem is a

Feasibility of Johnson Noise Thermometry based on Digital Signal Processing Techniques

International Nuclear Information System (INIS)

Hwang, In Koo; Kim, Yang Mo

2014-01-01

This paper presents an implementation strategy of noise thermometry based on a digital signal processing technique and demonstrates its feasibilities. A key factor in its development is how to extract the small thermal noise signal from other noises, for example, random noise from amplifiers and continuous electromagnetic interference from the environment. The proposed system consists of two identical amplifiers and uses a cross correlation function to cancel the random noise of the amplifiers. Then, the external interference noises are eliminated by discriminating the difference in the peaks between the thermal signal and external noise. The gain of the amplifiers is estimated by injecting an already known pilot signal. The experimental simulation results of signal processing methods have demonstrated that the proposed approach is an effective method in eliminating an external noise signal and performing gain correction for development of the thermometry

Implementing Audio-CASI on Windows’ Platforms

Science.gov (United States)

Cooley, Philip C.; Turner, Charles F.

2011-01-01

Audio computer-assisted self interviewing (Audio-CASI) technologies have recently been shown to provide important and sometimes dramatic improvements in the quality of survey measurements. This is particularly true for measurements requiring respondents to divulge highly sensitive information such as their sexual, drug use, or other sensitive behaviors. However, DOS-based Audio-CASI systems that were designed and adopted in the early 1990s have important limitations. Most salient is the poor control they provide for manipulating the video presentation of survey questions. This article reports our experiences adapting Audio-CASI to Microsoft Windows 3.1 and Windows 95 platforms. Overall, our Windows-based system provided the desired control over video presentation and afforded other advantages including compatibility with a much wider array of audio devices than our DOS-based Audio-CASI technologies. These advantages came at the cost of increased system requirements --including the need for both more RAM and larger hard disks. While these costs will be an issue for organizations converting large inventories of PCS to Windows Audio-CASI today, this will not be a serious constraint for organizations and individuals with small inventories of machines to upgrade or those purchasing new machines today. PMID:22081743

Lateralization of noise bursts in interaurally correlated or uncorrelated background noise using interaural level differences.

Science.gov (United States)

Reed, Darrin K; van de Par, Steven

2015-10-01

The interaural level difference (ILD) of a lateralized target source may be effectively reduced when the target is presented together with background noise containing zero ILD. It is not certain whether listeners perceive a position congruent with the reduced ILD or the actual target ILD in a lateralization task. Two sets of behavioral experiments revealed that many listeners perceived a position at or even larger than that corresponding to the presented target ILD when a temporal onset/offset asynchrony between the broadband target and the broadband background noise was present. When no temporal asynchrony was present, however, the perceived lateral position indicated a dependency on the coherence of the background noise for several listeners. With interaurally correlated background noise, listeners reported a reduced ILD resulting from the combined target and background noise stimulus. In contrast, several of the listeners made a reasonable estimate of the position corresponding to the target ILD for interaurally uncorrelated, broadband, background noise. No obvious difference in performance was seen between low- or high-frequency stimuli. Extension of a weighting template to the output of a standard equalization-cancellation model was shown to remove a lateral bias on the predicted target ILD resulting from the presence of background noise. Provided that an appropriate weighting template is applied based on knowledge of the background noise coherence, good prediction of the behavioral data is possible.

Structural Equation Modelling in Behavioral Intention to Use Safety Helmet Reminder System

Directory of Open Access Journals (Sweden)

Rosli Naida

2016-01-01

Full Text Available Motorcycle is one of private transportation which has been widely used in many countries including Malaysia. However, motorcycles are the most dangerous form of motorized transport. Royal Malaysian Police (PDRM statistics recorded that motorcycle is the highest vehicle (45.9% involved in traffic accident compared to other vehicles. The potential cause of the death to the motorcyclist was due to the head injury. One of strategy to mitigate this problem is through proper usage of safety helmet. Therefore, this paper was introduce a new approach on motorcyclist safety by using the Technology Acceptance Model (TAM with additional determinants that contribute to behavioral intention and to increase the proper usage of safety helmets among Malaysian motorcyclists. The Structural Equation Modelling (SEM was used to test the structural TAM proposed. The evaluation for structural model showed the goodness of fit indices are excellent fit. This study found that perceived ease of use, perceived usefulness and social norm are significant towards behavioral intention to use Safety Helmet Reminder System (SHR.

The protective effect of helmet use in motorcycle and bicycle accidents: a propensity score-matched study based on a trauma registry system.

Science.gov (United States)

Kuo, Spencer C H; Kuo, Pao-Jen; Rau, Cheng-Shyuan; Chen, Yi-Chun; Hsieh, Hsiao-Yun; Hsieh, Ching-Hua

2017-08-07

Transportation by motorcycle and bicycle has become popular in Taiwan, this study was designed to investigate the protective effect of helmet use during motorcycle and bicycle accidents by using a propensity score-matched study based on trauma registry system data. Data of adult patients hospitalized for motorcycle or bicycle accidents between January 1, 2009 and December 31, 2015 were retrieved from the Trauma Registry System. These included 7735 motorcyclists with helmet use, 863 motorcyclists without helmet use, 76 bicyclists with helmet use, and 647 bicyclists without helmet use. The primary outcome measurement was in-hospital mortality. Secondary outcomes were the hospital length of stay (LOS), intensive care unit (ICU) admission rate, and ICU LOS. Normally distributed continuous data were analyzed by the unpaired Student t-test, and non-normally distributed data were compared using the Mann-Whitney U-test. Two-sided Fisher exact or Pearson chi-square tests were used to compare categorical data. Propensity score matching (1:1 ratio using optimal method with a 0.2 caliper width) was performed using NCSS software, adjusting for the following covariates: sex, age, and comorbidities. Further logistic regression was used to evaluate the effect of helmet use on mortality rates of motorcyclists and bicyclists, respectively. The mortality rate for motorcyclists with helmet use (1.1%) was significantly lower than for motorcyclists without helmet use (4.2%; odds ratio [OR] 0.2; 95% confidence interval [CI]: 0.17-0.37; p Motorcycle helmets provide protection to adult motorcyclists involved in traffic accidents and their use is associated with a decrease in mortality rates and the risk of head injuries. However, no such protective effect of helmet use was observed for bicyclists involved in collisions.

Virtual Acoustics, Aeronautics and Communications

Science.gov (United States)

Begault, Durand R.; Null, Cynthia H. (Technical Monitor)

1996-01-01

An optimal approach to auditory display design for commercial aircraft would utilize both spatialized ("3-D") audio techniques and active noise cancellation for safer operations. Results from several aircraft simulator studies conducted at NASA Ames Research Center are reviewed, including Traffic alert and Collision Avoidance System (TCAS) warnings, spoken orientation "beacons" for gate identification and collision avoidance on the ground, and hardware for improved speech intelligibility. The implications of hearing loss amongst pilots is also considered.

Noise in position measurement by centroid calculation

International Nuclear Information System (INIS)

Volkov, P.

1996-01-01

The position of a particle trajectory in a gaseous (or semiconductor) detector can be measured by calculating the centroid of the induced charge on the cathode plane. The charge amplifiers attached to each cathode strip introduce noise which is added to the signal. This noise broadens the position resolution line. Our article gives an analytical tool to estimate the resolution broadening due to the noise per strip and the number of strips involved in the centroid calculation. It is shown that the position resolution increases faster than the square root of the number of strips involved. We also consider the consequence of added interstrip capacitors, intended to diminish the differential nonlinearity. It is shown that the position error increases slower than linearly with the interstrip capacities, due to the cancellation of correlated noise. The estimation we give, can be applied to calculations of position broadening other than the centroid finding. (orig.)

Application of Adaptive Noise Cancellation for Anti-Vibration in Yield Monitor

Directory of Open Access Journals (Sweden)

Yan LI

2014-04-01

Full Text Available In the process of grain harvest, yield monitor system acquires real-time spatial distribution information of crop yield to provide important basis of decision-making for subsequent assignments of precision agriculture. The measurement accuracy has been seriously affected by Combine working vibration. Based on an innovative test platform of wheat combine harvester for yield monitor, well simulate the working vibration at the field situation; impact-based grain flow sensor with the structure of dual-parallel-beams as test terminals and using the NI (National Instrument data acquisition card to acquire signals; grain impacted frequency as fundamental frequency to process harmonic extraction, and for extracted signals, applied the improved LMS adaptive algorithm to interference cancellation, aim to eliminate interference cased by working vibration. The comparative experiment show that the maximum relative error less than 2 % under the proposed method and proved that the proposed algorithm in this paper is effective.

An Analysis/Synthesis System of Audio Signal with Utilization of an SN Model

Directory of Open Access Journals (Sweden)

G. Rozinaj

2004-12-01

Full Text Available An SN (sinusoids plus noise model is a spectral model, in which theperiodic components of the sound are represented by sinusoids withtime-varying frequencies, amplitudes and phases. The remainingnon-periodic components are represented by a filtered noise. Thesinusoidal model utilizes physical properties of musical instrumentsand the noise model utilizes the human inability to perceive the exactspectral shape or the phase of stochastic signals. SN modeling can beapplied in a compression, transformation, separation of sounds, etc.The designed system is based on methods used in the SN modeling. Wehave proposed a model that achieves good results in audio perception.Although many systems do not save phases of the sinusoids, they areimportant for better modelling of transients, for the computation ofresidual and last but not least for stereo signals, too. One of thefundamental properties of the proposed system is the ability of thesignal reconstruction not only from the amplitude but from the phasepoint of view, as well.

Audio wiring guide how to wire the most popular audio and video connectors

CERN Document Server

Hechtman, John

2012-01-01

Whether you're a pro or an amateur, a musician or into multimedia, you can't afford to guess about audio wiring. The Audio Wiring Guide is a comprehensive, easy-to-use guide that explains exactly what you need to know. No matter the size of your wiring project or installation, this handy tool provides you with the essential information you need and the techniques to use it. Using The Audio Wiring Guide is like having an expert at your side. By following the clear, step-by-step directions, you can do professional-level work at a fraction of the cost.

A novel approach to background subtraction in contrast-enhanced dual-energy digital mammography with commercially available mammography devices: Noise minimization

International Nuclear Information System (INIS)

Contillo, Adriano; Di Domenico, Giovanni; Cardarelli, Paolo; Gambaccini, Mauro; Taibi, Angelo

2016-01-01

Purpose: Dual-energy image subtraction represents a useful tool to improve the detectability of small lesions, especially in dense breasts. A feature it shares with all x-ray imaging techniques is the appearance of fluctuations in the texture of the background, which can obscure the visibility of interesting details. The aim of the work is to investigate the main noise sources, in order to create a better performing subtraction mechanism. In particular, the structural noise cancellation was achieved by means of a suitable extension of the dual-energy algorithm. Methods: The effect of the cancellation procedure was tested on an analytical simulation of a target with varying structural composition. Subsequently, the subtraction algorithm was also applied to a set of actual radiographs of a breast phantom exhibiting a nonuniform background pattern. The background power spectra of the outcomes were computed and compared to the ones obtained from a standard subtraction algorithm. Results: The comparison between the standard and the proposed cancellations showed an overall suppression of the magnitudes of the spectra, as well as a flattening of the frequency dependence of the structural component of the noise. Conclusions: The proposed subtraction procedure provides an effective cancellation of the residual background fluctuations. When combined with the polychromatic correction already described in a companion publication, it results in a high performing dual-energy subtraction scheme for commercial mammography units.