Geochemical modeling of leaching from MSWI air-pollution control residues

NARCIS (Netherlands)

Astrup, T.; Dijkstra, J.J.; Comans, R.N.J.; Sloot, van der H.A.; Christensen, T.H.

2006-01-01

This paper provides an improved understanding of the leaching behavior of waste incineration air-pollution-control (APC) residues in a long-term perspective. Leaching was investigated by a series of batch experiments reflecting leaching conditions after initial washout of highly soluble salts from

Treatment of waste incinerator air-pollution-control residues with FeSO4: Concept and product characterization

DEFF Research Database (Denmark)

Lundtorp, Kasper; Jensen, Dorthe Lærke; Sørensen, Mette Abildgaard

2002-01-01

This paper describes a new concept for treatment of air- pollution-control (APC) residues from waste incineration and characterises the wastewater and stabilised residues generated by the process. The process involves mixing of APC-residues with a ferrous sulphate solution and subsequent oxidation...

Atividade residual de herbicidas aplicados ao solo em relação ao controle de quatro espécies de Amaranthus Residual activity of herbicides applied to the soil in relation to control of four Amaranthus Species

Directory of Open Access Journals (Sweden)

M.A. Raimondi

2010-01-01

Full Text Available Herbicidas aplicados em pré-emergência normalmente apresentam atividade residual no solo, controlando os primeiros fluxos germinativos das plantas daninhas e prevenindo a matocompetição inicial. O objetivo deste trabalho foi verificar o período de atividade residual proporcionado por doses de herbicidas suficientes para o controle pontual de 95% (C95 das espécies Amaranthus hybridus, A. lividus, A. spinosus e A. viridis, além de avaliar doses recomendadas desses herbicidas. O trabalho foi realizado em casa de vegetação, em solo de textura franco-argiloarenosa (20% de argila e 1,9 de matéria orgânica, e as doses dos herbicidas alachlor, diuron, oxyfluorfen, pendimethalin, prometryne, oxyfluorfen, S-metolachlor, trifluralin 450 e trifluralin 600 foram aplicadas aos 30, 20, 10 e 0 dias antes da semeadura das plantas daninhas. Avaliou-se o controle das plantas daninhas após a permanência dos herbicidas no solo por períodos de 0, 10, 20 e 30 dias depois da aplicação dos tratamentos (DAA. A atividade residual de alachlor e prometryne, na dose C95, não foi suficiente para o controle eficiente (>80% das espécies por períodos de até 30 DAA. Quanto ao alachlor, o emprego da dose recomendada não se refletiu em aumento considerável da atividade residual, exceto em relação a A. viridis. A dose recomendada de prometryne proporcionou controle eficiente das espécies até 30 DAA, exceto de A. hybridus. A dose recomendada de oxyfluorfen controlou eficientemente A. hybridus e A. spinosus até 30 DAA, espécies estas que não haviam sido eficientemente controladas pela dose C95. Trifluralin 450 promoveu controle residual eficiente de 30 DAA somente em relação a A. hybridus. Trifluralin 600 foi eficiente no controle de A. hybridus e A. viridis até os 30 DAA e até 29 e 28 DAA para A. lividus e A. spinosus, respectivamente. Clomazone não promoveu controle eficiente das espécies até 30 DAA, exceto de A. viridis. Diuron, pendimethalin e S

Manual of Standard Operating Procedures for Veterinary Drug Residue Analysis (Spanish Edition)

International Nuclear Information System (INIS)

2017-01-01

Laboratories are crucial to national veterinary drug residue monitoring programmes. However, one of the main challenges laboratories encounter is obtaining access to relevant methods of analysis. Thus, in addition to training, providing technical advice and transferring technology, the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture has resolved to develop clear and practical manuals to support Member State laboratories. The Coordinated Research Project (CRP) on Development of Radiometric and Allied Analytical Methods to Strengthen Residue Control Programs for Antibiotic and Anthelmintic Veterinary Drug Residues has developed a number of analytical methods as standard operating procedures (SOPs), which are now compiled here. This publication contains SOPs on chromatographic and spectrometric techniques, as well as radioimmunoassay and associated screening techniques, for various anthelmintic and antimicrobial veterinary drug residue analysis. Some analytical method validation protocols are also included. The publication is primarily aimed at food and environmental safety laboratories involved in testing veterinary drug residues, including under organized national residue monitoring programmes. It is expected to enhance laboratory capacity building and competence through the use of radiometric and complementary tools and techniques. The publication is also relevant for applied research on residues of veterinary drugs in food and environmental samples

Manual of Standard Operating Procedures for Veterinary Drug Residue Analysis (French Edition)

International Nuclear Information System (INIS)

2017-01-01

Laboratories are crucial to national veterinary drug residue monitoring programmes. However, one of the main challenges laboratories encounter is obtaining access to relevant methods of analysis. Thus, in addition to training, providing technical advice and transferring technology, the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture has resolved to develop clear and practical manuals to support Member State laboratories. The Coordinated Research Project (CRP) on Development of Radiometric and Allied Analytical Methods to Strengthen Residue Control Programs for Antibiotic and Anthelmintic Veterinary Drug Residues has developed a number of analytical methods as standard operating procedures (SOPs), which are now compiled here. This publication contains SOPs on chromatographic and spectrometric techniques, as well as radioimmunoassay and associated screening techniques, for various anthelmintic and antimicrobial veterinary drug residue analysis. Some analytical method validation protocols are also included. The publication is primarily aimed at food and environmental safety laboratories involved in testing veterinary drug residues, including under organized national residue monitoring programmes. It is expected to enhance laboratory capacity building and competence through the use of radiometric and complementary tools and techniques. The publication is also relevant for applied research on residues of veterinary drugs in food and environmental samples

Reactive control processes contributing to residual switch cost and mixing cost across the adult lifespan.

Science.gov (United States)

Whitson, Lisa R; Karayanidis, Frini; Fulham, Ross; Provost, Alexander; Michie, Patricia T; Heathcote, Andrew; Hsieh, Shulan

2014-01-01

In task-switching paradigms, performance is better when repeating the same task than when alternating between tasks (switch cost) and when repeating a task alone rather than intermixed with another task (mixing cost). These costs remain even after extensive practice and when task cues enable advanced preparation (residual costs). Moreover, residual reaction time mixing cost has been consistently shown to increase with age. Residual switch and mixing costs modulate the amplitude of the stimulus-locked P3b. This mixing effect is disproportionately larger in older adults who also prepare more for and respond more cautiously on these "mixed" repeat trials (Karayanidis et al., 2011). In this paper, we analyze stimulus-locked and response-locked P3 and lateralized readiness potentials to identify whether residual switch and mixing cost arise from the need to control interference at the level of stimulus processing or response processing. Residual mixing cost was associated with control of stimulus-level interference, whereas residual switch cost was also associated with a delay in response selection. In older adults, the disproportionate increase in mixing cost was associated with greater interference at the level of decision-response mapping and response programming for repeat trials in mixed-task blocks. These findings suggest that older adults strategically recruit greater proactive and reactive control to overcome increased susceptibility to post-stimulus interference. This interpretation is consistent with recruitment of compensatory strategies to compensate for reduced repetition benefit rather than an overall decline on cognitive flexibility.

Cover crop residue management for optimizing weed control

NARCIS (Netherlands)

Kruidhof, H.M.; Bastiaans, L.; Kropff, M.J.

2009-01-01

Although residue management seems a key factor in residue-mediated weed suppression, very few studies have systematically compared the influence of different residue management strategies on the establishment of crop and weed species. We evaluated the effect of several methods of pre-treatment and

Control levels for residual contamination in materials considered for recycle and reuse

International Nuclear Information System (INIS)

Hill, R.L.; Aaberg, R.L.; Baker, D.A.; Kennedy, W.E. Jr.

1993-09-01

Pacific Northwest Laboratory (PNL) is collecting data and conducting technical analyses to support joint efforts by the U.S. Department of Energy (DOE), Office of Environmental Guidance, Air, Water and Radiation Division (DOE/EH-232); by the U.S. Environmental Protection Agency (EPA); and by the U.S. Nuclear Regulatory Commission (NRC) to develop radiological control criteria for the recycle and reuse of scrap materials and equipment that contain residual radioactive contamination. The initial radiological control levels are the concentrations in or on materials considered for recycle or reuse that meet the individual (human) or industrial (electronics/film) dose criteria. The analysis identifies relevant radionuclides, potential mechanisms of exposure, and methods to determine possible non-health-related impacts from residual radioactive contamination in materials considered for recycle or reuse. The generic methodology and scenarios described here provide a basic framework for numerically deriving radiological control criteria for recycle or reuse. These will be adequately conservative for most situations

Reactive control processes contributing to residual switch cost and mixing cost in young and old adults

Directory of Open Access Journals (Sweden)

Lisa Rebecca Whitson

2014-04-01

Full Text Available In task-switching paradigms, performance is better when repeating the same task than when alternating between tasks (switch cost and when repeating a task alone rather than intermixed with another task (mixing cost. These costs remain even after extensive practice and when task cues enable advanced preparation (residual costs. Moreover, residual RT mixing cost has been consistently shown to increase with age. Residual switch and mixing costs modulate the amplitude of the stimulus-locked P3b. This mixing effect is disproportionately larger in older adults who also prepare more for and respond more cautiously on these ‘mixed’ repeat trials (Karayanidis et al., 2011. In this study, we examine stimulus-locked and response-locked P3 and lateralized readiness potentials to identify whether residual switch and mixing cost arise from the need to control interference at the level of stimulus processing or response processing. Residual mixing cost was associated with control of stimulus-level interference, whereas residual switch cost was also associated with a delay in response selection. In older adults, the disproportionate increase in mixing cost was associated with greater interference at the level of decision-response mapping and response programming for repeat trials in mixed-task blocks. We argue that, together with evidence of greater proactive control and more cautious responding for these trials, these findings suggest that older adults strategically recruit greater proactive and reactive control to overcome increased susceptibility to post-stimulus interference. This interpretation is consistent with recruitment of compensatory strategies to compensate for reduced repetition benefit rather than an overall decline on cognitive flexibility.

Assessment of long-term leaching from waste incineration air-pollution-control residues

DEFF Research Database (Denmark)

Astrup, Thomas; Mosbæk, Hans; Christensen, Thomas Højlund

2006-01-01

Assessment of long-term leaching from MSWI air-pollution-control (APC) residues is discussed with respect to use in environmental impact assessment, such as life-cycle assessment (LCA). A method was proposed for estimating leaching as a function of the liquid-to-solid (L/S) ratio in a long......-term perspective (L/S 5000l/kg). Data for changes in residue pH as a function of L/S was used in combination with pH dependent leaching data to predict leachate concentrations of Al, Ca, Cd, Ba, Mg, Ni, Pb, S, Pb, V and Zn as a function of L/S. Mass balance calculations were used to determine the element fractions...... leached with respect to L/S. The estimated long-term leaching from a semi-dry residue and a fly ash was compared with short-term leaching determined by batch tests at L/S 10l/kg, both carbonated and non-carbonated versions of the residues were investigated. Generally, very high L/S ratios above 2000l...

Measurement of the residual stresses in a PWR Control Rod Drive Mechanism nozzle

OpenAIRE

Coules, Harry; Smith, David

2018-01-01

Residual stress in the welds that attach Control Rod Drive Mechanism nozzles into the upper head of a PWR reactor vessel can influence the vessel's structural integrity and initiate Primary Water Stress Corrosion Cracking. PWSCC at Alloy 600 CRDM nozzles has caused primary coolant leakage in operating PWRs. We have used Deep Hole Drilling to characterise residual stresses in a PWR vessel head. Measurements of the internal cladding and nozzle attachment weld showed that although modest tensile...

Environmental insecticide residues from tsetse fly control measures in Uganda

International Nuclear Information System (INIS)

Sserunjoji-Sebalija, J.

1976-01-01

Up to June 1974 areas in Uganda totalling 8600km 2 have been successfully reclaimed from tsetse fly infestation by ground spray of 3% dieldrin water emulsions. A search for equally effective but less persistent and toxic compounds against tsetse flies has been unsuccessful. Fourteen insecticide formulations have been tested for their persistence on tree bark surfaces and, therefore, their availability and toxicity to the target tsetse flies. Only those compounds with a high immediate insecticidal activity (some higher than dieldrin) like endosulfan, Chlorfenvinphos and propoxur could merit further consideration in tsetse control. While some were toxic to tsetse as fresh deposits, they lacked sufficient persistence. A study of the environmental implication from the continued use of the highly persistent and toxic dieldrin has provided useful data on residues likely to be found both in terrestrial and aquatic fauna and flora. These are generally low. Moreover, there is evidence of degradation in some fish species (Protopterus aethiopicus and Clarias). Also, dilution factors and adsorption involving the muddy nature of water run-off, etc., and controlled burning of grasses after tsetse eradication would tend to inactivate the residual insecticide and protect aquatic systems. The general findings have indicated less risk than anticipated of the environmental contamination from tsetse control by application of persistent and toxic insecticides. (author)

Usefulness of food chain information provided by Dutch finishing pig producers to control antibiotic residues in pork.

Science.gov (United States)

van Wagenberg, Coen P A; Backus, Gé B C; van der Vorst, Jack G A J; Urlings, Bert A P

2012-11-01

The EU prescribes that food business operators must use food chain information to assist in food safety control. This study analyses usefulness of food chain information about antibiotic usage covering the 60-day period prior to delivery of pigs to slaughter in the control of antibiotic residues in pork. A dataset with 479 test results for antibiotic residues in tissue samples of finishing pigs delivered to a Dutch slaughter company was linked to information provided by pig producers about antibiotic usage in these finishing pigs. Results show that twice as many producers reported using antibiotics in the group of 82 producers with antibiotic residues (11.0%) compared to the group without antibiotic residues (5.5%) (p=0.0686). For 89% of consignments with a finishing pig with antibiotic residues, the producer reported 'did not use antibiotics'. Food chain information about antibiotic usage provided by Dutch pig producers was no guarantee for absence of antibiotic residues in delivered finishing pigs. Copyright © 2012 Elsevier B.V. All rights reserved.

On-site treatment and landfilling of MSWI air pollution control residues

DEFF Research Database (Denmark)

Lundtorp, Kasper; Jensen, Dorthe Lærke; Sørensen, Mette Abildgaard

2003-01-01

the process, collected through the drainage system, contained large concentrations of salts (Cl: 14–30 g/l, Na: 4–9 g/l, K: 5–11 g/l, Ca: 2–12 g/l) but low concentrations of trace metals (e.g. Pb: 14–100 μg/l, Cd: leaching......Air pollution control (APC) residues from municipal solid waste incineration (MSWI) are difficult to landfill due to substantial leaching of trace metals. An on-site pretreatment prior to landfilling of APC-residues was investigated in terms of bench-scale experiments with a semidry APC...... of the leaching, concentrations of trace metals were reduced by up to four orders of magnitude....

Adaptive Control Using Residual Mode Filters Applied to Wind Turbines

Science.gov (United States)

Frost, Susan A.; Balas, Mark J.

2011-01-01

Many dynamic systems containing a large number of modes can benefit from adaptive control techniques, which are well suited to applications that have unknown parameters and poorly known operating conditions. In this paper, we focus on a model reference direct adaptive control approach that has been extended to handle adaptive rejection of persistent disturbances. We extend this adaptive control theory to accommodate problematic modal subsystems of a plant that inhibit the adaptive controller by causing the open-loop plant to be non-minimum phase. We will augment the adaptive controller using a Residual Mode Filter (RMF) to compensate for problematic modal subsystems, thereby allowing the system to satisfy the requirements for the adaptive controller to have guaranteed convergence and bounded gains. We apply these theoretical results to design an adaptive collective pitch controller for a high-fidelity simulation of a utility-scale, variable-speed wind turbine that has minimum phase zeros.

Leaching Behavior of Circulating Fluidised Bed MSWI Air Pollution Control Residue in Washing Process

Directory of Open Access Journals (Sweden)

Zhiliang Chen

2016-09-01

Full Text Available In this study, air pollution control (APC residue is conducted with water washing process to reduce its chloride content. A novel electrical conductivily (EC measurement method is proposed to monitor the dynamic change of chloride concentrations in leachate as well as the chloride content of the residue. The method equally applies to various washing processes with different washing time, liquid/solid ratio and washing frequency. The results show that washing effectively extracts chloride salts from APC residues, including those from circulating fluidized bed (CFB municipal solid waste incineration (MSWI. The most appropriate liquid/solid ratio and washing time in the first washing are found to be around 4 L water per kg of APC residue and 30 min, respectively, and washing twice is required to obtain maximum dissolution. The pH value is the major controlling factor of the heavy metals speciation in leachate, while chloride concentration also affects the speciation of Cd. Water washing causes no perceptible transfer of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs from the APC residue to leachate. The chloride concentration is strongly related with electrical conductivity (EC, as well as with the concentrations of calcium, sodium and potassium of washing water. Their regression analyses specify that soluble chloride salts and EC could act as an indirect indicator to monitor the change of chloride concentration and remaining chloride content, thus, contributing to the selection of the optimal washing conditions.

Lipid residues preserved in sheltered bedrock features at Gila Cliff Dwellings National Monument, New Mexico

Directory of Open Access Journals (Sweden)

Tammy Buonasera

2016-10-01

Bedrock features represent various economic, social, and symbolic aspects of past societies, but have historically received little study, particularly in North America. Fortunately, new techniques for analyzing spatial configurations, use-wear, and organic residues are beginning to unlock more of the interpretive potential of these features. Though preliminary in nature, the present study contributes to this trend by documenting an application of lipid analysis to bedrock features in a dry rockshelter. Results of this initial application indicate that bedrock features in dry rockshelters may provide especially favorable conditions for the preservation and interpretation of ancient organic residues. Abundant lipids, comparable to concentrations present in some pottery sherds, were extracted from a bedrock grinding surface at Gila Cliff Dwellings National Monument and analyzed using gas chromatography-mass spectrometry. Though the lipids were highly oxidized, degradation products indicative of former unsaturated fatty acids were retained. Comparisons to experimentally aged residues, and absence of a known biomarker for maize, indicate that the bulk of the lipids preserved in the milling surface probably derive from processing an oily nut or seed resource, and not from processing maize. Substantially lower amounts of lipids were recovered from a small, blackened cupule. It is hypothesized that some portion of the lipids in the blackened cupule was deposited from condensed smoke of cooking and heating fires in the caves. Potential for the preservation of organic residues in similar sheltered bedrock contexts is discussed, and a practical method for sampling bedrock features in the field is described.

12 CFR 23.21 - Estimated residual value.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Estimated residual value. 23.21 Section 23.21...) Leases § 23.21 Estimated residual value. (a) Recovery of investment and costs. A national bank's estimate of the residual value of the property that the bank relies upon to satisfy the requirements of a full...

Monitoring residue in animals and primary products of animal origin

Directory of Open Access Journals (Sweden)

Janković Saša

2008-01-01

Full Text Available The objective of control and systematic monitoring of residue is to secure, by the examination of a corresponding number of samples, the efficient monitoring of the residue level in tissues and organs of animals, as well as in primary products of animal origin. This creates possibilities for the timely taking of measures toward the securing of food hygiene of animal origin and the protection of public health. Residue can be a consequence of the inadequate use of medicines in veterinary medicine and pesticides in agriculture and veterinary medicine, as well as the polluting of the environment with toxic elements, dioxins, polychlorinated biphenyls, and others. Residue is being monitored in Serbia since 1972, and in 2004, national monitoring was brought to the level of EU countries through significant investments by the Ministry of Agriculture, Forestry and Water Management. This is also evident in the EU directives which permit exports of all kinds of meat and primary products of animal origin, covered by the Residue Monitoring Program. The program of systematic examinations of residue has been coordinated with the requirements of the European Union, both according to the type of examined substance, as well as according to the number of samples and the applied analytical techniques. In addition to the development of methods and the including of new harmful substances into the monitoring programme, it is also necessary to coordinate the national regulations that define the maximum permitted quantities of certain medicines and contaminants with the EU regulations, in order to protect the health of consumers as efficiently as possible, and for the country to take equal part in international trade.

Survey of Veterinary Drug Residues in Raw Milk in Hebei Province, China.

Science.gov (United States)

Han, Rong-Wei; Yu, Zhong-Na; Zhen, Tian-Yuan; Wang, Jun

2017-10-17

The objective of this study was to investigate the occurrence of veterinary drug residues in raw milk from Hebei, the second-largest dairy production province in the People's Republic of China. A total of 192 raw milk samples were collected from 64 milk stations in seven districts. Twenty-eight veterinary drug residues were analyzed by ultraperformance liquid chromatography with tandem mass spectrometry based on a China National Standard. Raw milk samples with multiple residues of veterinary drugs were not found in the present study. Residues of four veterinary drugs, penicillin G, sulfacetamide, trimethoprim, and lincomycin, were detected in 12 (6.25%) raw milk samples, with detection ratios of 1.04, 0.52, 3.13, and 1.56%, respectively. All veterinary drug residues detected were under the maximum residue levels as regulated by China, the European Union, the United States, and the Codex Alimentarius Commission. In general, raw milk from Hebei province was considered relatively safe for human consumption because of the low prevalence of veterinary drug residues. However, stringent control measurements for veterinary drug residues in raw milk are required because some veterinary drugs were detected in milk from some areas of Hebei province.

Control system of an anaerobia reactor used in the treatment of the Industrial residual waters

International Nuclear Information System (INIS)

Duque, Mauricio; Giraldo, Eugenio; Bello Frank

1995-01-01

The technology of the anaerobia digestion, has had a wide acceptance in the Colombian means for the treatment of industrial residual waters, especially for the economic advantages that it present and the good purification results. The technology of the anaerobia digestion for the treatment of residual waters, is based in the conversion of the organic matter present in the polluted waters, in methane and carbon dioxide. These two gases are removed of the reactor by means of special structures of gathering. Microorganisms that are sensitive to the changes of the pH mediate the conversion of the organic matter to CH4 and CO2. Therefore, the control on the pH is necessary for a correct behavior of the reactor. At the moment many industries are implementing plans of contamination control, that involve treatment of residual waters for means anaerobia. The present investigation is part of a wide work program in the technology of the anaerobia digestion. It is looked for to develop a monitored system and automatic control of reactors discharge anaerobia appraises, in a combined effort among the departments of Civil and Electric Engineering of the Andes University

77 FR 24671 - Compliance Guide for Residue Prevention and Agency Testing Policy for Residues

Science.gov (United States)

2012-04-25

... Hazard Analysis and Critical Control Points (HACCP) inspection system, another important component of the NRP is to provide verification of residue control in HACCP systems. As part of the HACCP regulation... guide, and FSIS finds violative residues, the establishment's HACCP system may be inadequate under 9 CFR...

Influence of different disease control pesticide strategies on multiple pesticide residue levels in apple

DEFF Research Database (Denmark)

Poulsen, Mette Erecius; Naef, A.; Gasser, S.

2009-01-01

Seven pesticide application strategies were investigated to control apple scab (Venturia inaequalis) and powdery mildew (Podosphaera leucotricha) and, at the same time.. fulfil the new quality standards implemented by some German retailers. These demand that pesticide residues should be below 80....... The trials were conducted at two sites in Switzerland, in 2007, and all strategies and applications were in accordance with actual practice. Four replicates of apple samples from each strategy were then analysed for pesticide residues. The incidence of infection with apple scab and powdery mildew were...... monitored during the season in order to evaluate the efficacy of the different strategies. The efficacies of the different strategies against apple scab and powdery mildew were between 84% and 100% successful. In general, the level of pesticide residues found correlated with application rate and time...

Mapping allostery through computational glycine scanning and correlation analysis of residue-residue contacts.

Science.gov (United States)

Johnson, Quentin R; Lindsay, Richard J; Nellas, Ricky B; Fernandez, Elias J; Shen, Tongye

2015-02-24

Understanding allosteric mechanisms is essential for the physical control of molecular switches and downstream cellular responses. However, it is difficult to decode essential allosteric motions in a high-throughput scheme. A general two-pronged approach to performing automatic data reduction of simulation trajectories is presented here. The first step involves coarse-graining and identifying the most dynamic residue-residue contacts. The second step is performing principal component analysis of these contacts and extracting the large-scale collective motions expressed via these residue-residue contacts. We demonstrated the method using a protein complex of nuclear receptors. Using atomistic modeling and simulation, we examined the protein complex and a set of 18 glycine point mutations of residues that constitute the binding pocket of the ligand effector. The important motions that are responsible for the allostery are reported. In contrast to conventional induced-fit and lock-and-key binding mechanisms, a novel "frustrated-fit" binding mechanism of RXR for allosteric control was revealed.

Influence of postsurgical residual tumor volume on local control in radiotherapy for maxillary sinus cancer

Energy Technology Data Exchange (ETDEWEB)

Kawashima, Mitsuhiko; Ogino, Takashi; Hayashi, Ryuichi; Ishikura, Satoshi; Nihei, Keiji; Ito, Yoshinori; Ikeda, Hiroshi; Ebihara, Satoshi [National Cancer Center, Kashiwa, Chiba (Japan). Hospital East; Itai, Yuji

2001-05-01

The aim was to study the influence of postsurgical gross residual tumor volume on local control of maxillary sinus cancer treated with radiotherapy combined with debulking surgery. Forty-three patients who underwent combined surgery and radiotherapy (50-72 Gy, median 60 Gy) for squamous cell carcinoma of the maxillary sinus were reviewed. Gross residual tumor volume (GRTV) after surgery was measured on computed tomograms obtained during the radiotherapy planning. Patients were classified according to GRTV as follows: group AA, GRTV=0 (microscopic residual, n=2); group A, GRTV <10 cm{sup 3} (n=24); group B, 10-40 cm{sup 3} (n=9); and group C, {>=}40 cm{sup 3} (n=8). The relationship between local control and GRTV was analyzed using univariate and multivariate analysis. The 2-year local control rate for all patients was 62%. The differences in local control rates between groups AA, A and B were not significant (P<0.05), but the rate was significantly lower in group C than in the other groups (69% at 2 years vs 31% at 1 year, P<0.001). Multivariate analysis showed that GRTV (P=0.002) and histological differentiation (poorly differentiated histology was favorable, P=0.035) were independent prognostic factors and that intraarterial chemotherapy and administered total dose were not. Local control in groups A and B significantly depended on the total dose of radiotherapy, with 2-year control rates of patients receiving 50 Gy (n=6) and {>=}60 Gy (n=27) of 17% vs 79%, respectively (P<0.001). Our data suggest that adequate, not complete, debulking associated with a total radiotherapy dose of {>=}60 Gy can provide satisfactory local control for patients with squamous cell carcinoma of the maxillary sinus. (author)

Control criteria for residual contamination in materials considered for recycle and reuse

International Nuclear Information System (INIS)

Kennedy, W.E. Jr.; Hill, R.L.; Aaberg, R.L.

1993-11-01

Pacific Northwest Laboratory (PNL) is collecting data and conducting technical analyses to support the US Department of Energy (DOE), Office of Environmental Guidance, Air, Water, and Radiation Division (DOE/EH-232) in determining the feasibility of developing radiological control criteria for recycling or reuse of metals or equipment containing residual radioactive contamination from DOE operations. The criteria, framed as acceptable concentrations for release of materials for recycling or reuse, will be risk-based and will be developed through analysis of radiation exposure scenarios and pathways. The analysis will include evaluation of relevant radionuclides, potential mechanisms of exposure, and non-health-related impacts of residual radioactivity on electronics and film. The analyses will consider 42 key radionuclides that are generated during DOE operations and may be contained in recycled or reused metals or equipment

Automatic transfer function generation using contour tree controlled residue flow model and color harmonics.

Science.gov (United States)

Zhou, Jianlong; Takatsuka, Masahiro

2009-01-01

Transfer functions facilitate the volumetric data visualization by assigning optical properties to various data features and scalar values. Automation of transfer function specifications still remains a challenge in volume rendering. This paper presents an approach for automating transfer function generations by utilizing topological attributes derived from the contour tree of a volume. The contour tree acts as a visual index to volume segments, and captures associated topological attributes involved in volumetric data. A residue flow model based on Darcy's Law is employed to control distributions of opacity between branches of the contour tree. Topological attributes are also used to control color selection in a perceptual color space and create harmonic color transfer functions. The generated transfer functions can depict inclusion relationship between structures and maximize opacity and color differences between them. The proposed approach allows efficient automation of transfer function generations, and exploration on the data to be carried out based on controlling of opacity residue flow rate instead of complex low-level transfer function parameter adjustments. Experiments on various data sets demonstrate the practical use of our approach in transfer function generations.

Recycling of air pollution control residues from municipal solid waste incineration into lightweight aggregates.

Science.gov (United States)

Quina, Margarida J; Bordado, João M; Quinta-Ferreira, Rosa M

2014-02-01

This work focuses on the assessment of technological properties and on the leaching behavior of lightweight aggregates (LWA) produced by incorporating different quantities of air pollution control (APC) residues from municipal solid waste (MSW) incineration. Currently this hazardous waste has been mostly landfilled after stabilization/solidification. The LWA were produced by pelletizing natural clay, APC residues as-received from incineration plant, or after a washing treatment, a small amount of oil and water. The pellets were fired in a laboratory chamber furnace over calcium carbonate. The main technological properties of the LWA were evaluated, mainly concerning morphology, bulk and particle densities, compressive strength, bloating index, water adsorption and porosity. Given that APC residues do not own expansive (bloating) properties, the incorporation into LWA is only possible in moderate quantities, such as 3% as received or 5% after pre-washing treatment. The leaching behavior of heavy metals from sintered LWA using water or acid solutions was investigated, and despite the low acid neutralization capacity of the synthetic aggregates, the released quantities were low over a wide pH range. In conclusion, after a washing pre-treatment and if the percentage of incorporation is low, these residues may be incorporated into LWA. However, the recycling of APC residues from MSW incineration into LWA does not revealed any technical advantage. Copyright © 2013 Elsevier Ltd. All rights reserved.

[Internal quality control of the blood products in the Lomé National Blood Transfusion Centre].

Science.gov (United States)

Fétéké, L; Mawussi, K; Lakté, P; Kuéviakoe, I M; Haudrechy, D; Ségbéna, A Y

2008-07-01

Evaluate the conformity of blood red cells units prepared in the Lomé CNTS with European norms concerning volume, haemoglobin content and haematocrite. Measure the conservation of the haemostatic properties and the rate of haemostasis factors V and VIII in the fresh frozen plasma. Measure the rate of residual cells in the plasma. In the year 2006, from March 1st to April 15th, we analysed the quality of 135 units of whole blood, red blood cells (RBC) and plasma from blood donors in the Lomé National Blood Transfusion Centre. The quality control had concerned: the volume of whole blood units; the volume, the haemoglobin content and the haematocrite of red blood cells units; the volume, the prothrombin rate, the cephalin with activator time (TCA), the rate of haemostasis factors V and VIII and the number of residual cells (red cells, leucocytes and platelets) in the plasma. Among the 135 units of whole blood which were controlled, 50.57% were in conformity with the norms concerning the volume. The red blood cells units were in conformity with norms concerning their volume, their haemoglobin content and their haematocrite respectively in 21.48%, 80.75% and 20% of the cases. The volume of 75.56% of the plasma units controlled were conform with the norm. All of the plasma units were conform with the norm concerning the number of residual platelets while the number of residual red blood cells and leucocytes were conform respectively in 80.74% and 60%. The percentage of conformity concerning the prothrombin rate, the TCA, the coagulation factor V and the factor VIII were respectively 66.67; 97.78; 48.89 and 47.4 before freezing, and 54.81; 88.14; 64.44; 84.44 a month after freezing. To improve the quality of the new blood products of the Lomé CNTS, some correctives actions must be applied concerning the adequate volume of blood which must be collected from the donors, the position of the blood bags in during the centrifugation and the volume of plasma which must be

Ammonia volatilization from crop residues and frozen green manure crops

Science.gov (United States)

de Ruijter, F. J.; Huijsmans, J. F. M.; Rutgers, B.

2010-09-01

Agricultural systems can lose substantial amounts of nitrogen (N). To protect the environment, the European Union (EU) has adopted several directives that set goals to limit N losses. National Emission Ceilings (NEC) are prescribed in the NEC directive for nitrogen oxides and ammonia. Crop residues may contribute to ammonia volatilization, but sufficient information on their contribution to the national ammonia volatilization is lacking. Experiments were carried out with the aim to assess the ammonia volatilization of crop residues left on the soil surface or incorporated into the soil under the conditions met in practice in the Netherlands during late autumn and winter. Ammonia emission from residues of broccoli, leek, sugar beet, cut grass, fodder radish (fresh and frozen) and yellow mustard (frozen) was studied during two winter seasons using volatilization chambers. Residues were either placed on top of soil or mixed with soil. Mixing residues with soil gave insignificant ammonia volatilization, whereas volatilization was 5-16 percent of the N content of residues when placed on top of soil. Ammonia volatilization started after at least 4 days. Total ammonia volatilization was related to C/N-ratio and N concentration of the plant material. After 37 days, cumulative ammonia volatilization was negligible from plant material with N concentration below 2 percent, and was 10 percent of the N content of plant material with 4 percent N. These observations can be explained by decomposition of plant material by micro-organisms. After an initial built up of the microbial population, NH 4+ that is not needed for their own growth is released and can easily emit as NH 3 at the soil surface. The results of the experiments were used to estimate the contribution of crop residues to ammonia volatilization in the Netherlands. Crop residues of arable crops and residues of pasture topping may contribute more than 3 million kg NH 3-N to the national ammonia volatilization of the

US national material control and accounting system

International Nuclear Information System (INIS)

Smith, C.N.

1984-01-01

The State System of Accounting and Control (SSAC) for fuel cycle facilities in the licensed, commercial sector of the US nuclear community, and details of the material control and accounting measures dealing with the national safeguards program are discussed. The concept and role of the Fundamental Nuclear Material Control (FNMC) Plan is discussed. Also, the relationship between the national safeguards program and the international safeguards program of the US SSAC are described

National Drug Control Strategy, 2011

Science.gov (United States)

Office of National Drug Control Policy, 2011

2011-01-01

In May of 2010, President Obama released the Administration's inaugural "National Drug Control Strategy". Based on the premise that drug use and its consequences pose a threat not just to public safety, but also to public health, the 2010 "Strategy" represented the first comprehensive rebalancing of Federal drug control policy in the nearly 40…

Sustainable System for Residual Hazards Management

International Nuclear Information System (INIS)

Kevin M. Kostelnik; James H. Clarke; Jerry L. Harbour

2004-01-01

Hazardous, radioactive and other toxic substances have routinely been generated and subsequently disposed of in the shallow subsurface throughout the world. Many of today's waste management techniques do not eliminate the problem, but rather only concentrate or contain the hazardous contaminants. Residual hazards result from the presence of hazardous and/or contaminated material that remains on-site following active operations or the completion of remedial actions. Residual hazards pose continued risk to humans and the environment and represent a significant and chronic problem that require continuous long-term management (i.e. >1000 years). To protect human health and safeguard the natural environment, a sustainable system is required for the proper management of residual hazards. A sustainable system for the management of residual hazards will require the integration of engineered, institutional and land-use controls to isolate residual contaminants and thus minimize the associated hazards. Engineered controls are physical modifications to the natural setting and ecosystem, including the site, facility, and/or the residual materials themselves, in order to reduce or eliminate the potential for exposure to contaminants of concern (COCs). Institutional controls are processes, instruments, and mechanisms designed to influence human behavior and activity. System failure can involve hazardous material escaping from the confinement because of system degradation (i.e., chronic or acute degradation) or by external intrusion of the biosphere into the contaminated material because of the loss of institutional control. An ongoing analysis of contemporary and historic sites suggests that the significance of the loss of institutional controls is a critical pathway because decisions made during the operations/remedial action phase, as well as decisions made throughout the residual hazards management period, are key to the long-term success of the prescribed system. In fact

Metal releases from a municipal solid waste incineration air pollution control residue mixed with compost.

Science.gov (United States)

Van Praagh, M; Persson, K M

2008-08-01

The influence of 10 wt.% mature compost was tested on the heavy metal leachate emissions from a calcium-rich municipal solid waste incineration air pollution control residue (MSWI APC). Apart from elongated columns (500 and 1250 mm), an otherwise norm compliant European percolation test setup was used. More than 99% of the metals Al, As, Cd, Cr, Cu, Fe and Ni were left in the APC residue after leaching to a liquid-to-solid ratio (L/S) of 10. Apparent short-term effects of elevated leachate DOC concentrations on heavy metal releases were not detected. Zn and Pb leachate concentrations were one order of magnitude lower for L/S 5 and 10 from the pure APC residue column, which suggests a possible long-term effect of compost on the release of these elements. Prolonging the contact time between the pore water and the material resulted in elevated leachate concentrations at L/S 0.1 to L/S 1 by a factor of 2. Only Cr and Pb concentrations were at their maxima in the first leachates at L/S 0.1. Equilibrium speciation modelling with the PHREEQC code suggested portlandite (Ca(OH)2) to control Ca solubility and pH.

Properties of sintered glass-ceramics prepared from plasma vitrified air pollution control residues

International Nuclear Information System (INIS)

Roether, J.A.; Daniel, D.J.; Amutha Rani, D.; Deegan, D.E.; Cheeseman, C.R.; Boccaccini, A.R.

2010-01-01

Air pollution control (APC) residues, obtained from a major UK energy from waste (EfW) plant, processing municipal solid waste, have been blended with silica and alumina and melted using DC plasma arc technology. The glass produced was crushed, milled, uni-axially pressed and sintered at temperatures between 750 and 1150 deg. C, and the glass-ceramics formed were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Mechanical properties assessed included Vickers's hardness, flexural strength, Young's modulus and thermal shock resistance. The optimum sintering temperature was found to be 950 deg. C. This produced a glass-ceramic with high density (∼2.58 g/cm 3 ), minimum water absorption (∼2%) and relatively high mechanical strength (∼81 ± 4 MPa). Thermal shock testing showed that 950 deg. C sintered samples could withstand a 700 deg. C quench in water without micro-cracking. The research demonstrates that glass-ceramics can be readily formed from DC plasma treated APC residues and that these have comparable properties to marble and porcelain. This novel approach represents a technically and commercially viable treatment option for APC residues that allow the beneficial reuse of this problematic waste.

Strategic model of national rabies control in Korea.

Science.gov (United States)

Cheong, Yeotaek; Kim, Bongjun; Lee, Ki Joong; Park, Donghwa; Kim, Sooyeon; Kim, Hyeoncheol; Park, Eunyeon; Lee, Hyeongchan; Bae, Chaewun; Oh, Changin; Park, Seung-Yong; Song, Chang-Seon; Lee, Sang-Won; Choi, In-Soo; Lee, Joong-Bok

2014-01-01

Rabies is an important zoonosis in the public and veterinary healthy arenas. This article provides information on the situation of current rabies outbreak, analyzes the current national rabies control system, reviews the weaknesses of the national rabies control strategy, and identifies an appropriate solution to manage the current situation. Current rabies outbreak was shown to be present from rural areas to urban regions. Moreover, the situation worldwide demonstrates that each nation struggles to prevent or control rabies. Proper application and execution of the rabies control program require the overcoming of existing weaknesses. Bait vaccines and other complex programs are suggested to prevent rabies transmission or infection. Acceleration of the rabies control strategy also requires supplementation of current policy and of public information. In addition, these prevention strategies should be executed over a mid- to long-term period to control rabies.

Modeling the Influence of Diffusion-Controlled Reactions and Residual Termination and Deactivation on the Rate and Control of Bulk ATRP at High Conversions

Directory of Open Access Journals (Sweden)

Ali Mohammad Rabea

2015-04-01

Full Text Available In high-conversion atom transfer radical polymerization (ATRP, all the reactions, such as radical termination, radical deactivation, dormant chain activation, monomer propagation, etc. could become diffusion controlled sooner or later, depending on relative diffusivities of the involved reacting species. These diffusion-controlled reactions directly affect the rate of polymerization and the control of polymer molecular weight. A model is developed to investigate the influence of diffusion-controlled reactions on the high conversion ATRP kinetics. Model simulation reveals that diffusion-controlled termination slightly increases the rate, but it is the diffusion-controlled deactivation that causes auto-acceleration in the rate (“gel effect” and loss of control. At high conversions, radical chains are “trapped” because of high molecular weight. However, radical centers can still migrate through (1 radical deactivation–activation cycles and (2 monomer propagation, which introduce “residual termination” reactions. It is found that the “residual termination” does not have much influence on the polymerization kinetics. The migration of radical centers through propagation can however facilitate catalytic deactivation of radicals, which improves the control of polymer molecular weight to some extent. Dormant chain activation and monomer propagation also become diffusion controlled and finally stop the polymerization when the system approaches its glass state.

RESIDUAL RISK ASSESSMENT: ETHYLENE OXIDE ...

Science.gov (United States)

This document describes the residual risk assessment for the Ethylene Oxide Commercial Sterilization source category. For stationary sources, section 112 (f) of the Clean Air Act requires EPA to assess risks to human health and the environment following implementation of technology-based control standards. If these technology-based control standards do not provide an ample margin of safety, then EPA is required to promulgate addtional standards. This document describes the methodology and results of the residual risk assessment performed for the Ethylene Oxide Commercial Sterilization source category. The results of this analyiss will assist EPA in determining whether a residual risk rule for this source category is appropriate.

VA National Bed Control System

Data.gov (United States)

Department of Veterans Affairs — The VA National Bed Control System records the levels of operating, unavailable and authorized beds at each VAMC, and it tracks requests for changes in these levels....

Pesticide residues in locally available cereals and vegetables

International Nuclear Information System (INIS)

Cunanan, S.A.; Santos, F.L.; Bonoan, L.S.

1976-03-01

Vegetable samples (pechay, cabbage, lettuce, green beans and tomatoes) bought from public markets in the Metro Manila area were analyzed for pesticide residues using gas chromatography. The samples analyzed in 1968-69 contained high levels of chlorinated pesticides such as DDT, Aldrin, Endrin, and Thiodan, while in the samples analyzed in January 1976, no chlorinated and organophosphate pesticides were detected. Cereal samples (rice, corn and sorghum) were obtained from the National Grains Authority and analyzed for pesticide residues and bromine residues. Total bromine residues was determined by neutron activation analysis. In most of the samples analyzed, the concentrations of pesticide residues were below the tolerance levels set by the FAO/WHO Committee on Pesticide Residues in Foods. An exception was one rice sample from Thailand, the bromine residue content (110ppm) of which exceeds the tolerance level of 50ppm

Long-term leaching from MSWI air-pollution-control residues: Leaching characterization and modeling

DEFF Research Database (Denmark)

Hyks, Jiri; Astrup, Thomas; Christensen, Thomas Højlund

2009-01-01

Long-term leaching of Ca, Fe, Mg, K, Na, S, Al, As, Ba, Cd, Co, Cr, Cu, Hg, Mn, Ni, Pb, Zn, Mo, Sb, Si, Sri, Sr, Ti, V, P, Cl, and dissolved organic carbon from two different municipal solid waste incineration (MSWI) air-pollution-control residues was monitored during 24 months of column percolat......Long-term leaching of Ca, Fe, Mg, K, Na, S, Al, As, Ba, Cd, Co, Cr, Cu, Hg, Mn, Ni, Pb, Zn, Mo, Sb, Si, Sri, Sr, Ti, V, P, Cl, and dissolved organic carbon from two different municipal solid waste incineration (MSWI) air-pollution-control residues was monitored during 24 months of column...... percolation experiments; liquid-to-solid (L/S) ratios of 200-250 L/kg corresponding to more than 10,000 years in a conventional landfill were reached. Less than 2% of the initially present As, Cu, Pb, Zn, Cr, and Sb had leached during the Course of the experiments. Concentrations of Cd, Fe, Mg, Hg, Mn, Ni, Co......, Sn, Ti, and P were generally bellow 1 mu g/L; overall less than 1% of their mass leached. Column leaching data were further used in a two-step geochemical modeling in PHREEQC in order to (i) identify solubility controlling minerals and (ii) evaluate their interactions in a water-percolated column...

76 FR 23914 - National Organic Program; Periodic Residue Testing

Science.gov (United States)

2011-04-29

... NOP. Residue testing plays an important role in organic certification by providing a means for... OFPA (7 U.S.C. 6503 through 6507) from creating certification programs to certify organic farms or... State organic certification program may contain additional requirements for the production and handling...

A Promising Material by Using Residue Waste from Bisphenol A Manufacturing to Prepare Fluid-Loss-Control Additive in Oil Well Drilling Fluid

Directory of Open Access Journals (Sweden)

Zhi-Lei Zhang

2013-01-01

Full Text Available The residues mixture from Bisphenol A manufacturing process was analyzed. Fourier transform infrared (FTIR spectroscopy, gas chromatography-mass spectrometry (GC-MS, and nuclear magnetic resonance (NMR were used to characterize the residues. The results indicated that the residues were complex mixture of several molecules. 3-(2-Hydroxyphenyl-1,1,3-trimethyl-2,3-dihydro-1H-inden-5-ol and phenol were the main components of the residues. The technical feasibility of using it as phenol replacement in fluid-loss-control additive production was also investigated. The fluid-loss-control capacity of the novel additive was systematically investigated. It was discovered that the well fluid-loss performance of the prepared additive can be achieved, especially at high temperature.

Adaptive Control of Non-Minimum Phase Modal Systems Using Residual Mode Filters2. Parts 1 and 2

Science.gov (United States)

Balas, Mark J.; Frost, Susan

2011-01-01

Many dynamic systems containing a large number of modes can benefit from adaptive control techniques, which are well suited to applications that have unknown parameters and poorly known operating conditions. In this paper, we focus on a direct adaptive control approach that has been extended to handle adaptive rejection of persistent disturbances. We extend this adaptive control theory to accommodate problematic modal subsystems of a plant that inhibit the adaptive controller by causing the open-loop plant to be non-minimum phase. We will modify the adaptive controller with a Residual Mode Filter (RMF) to compensate for problematic modal subsystems, thereby allowing the system to satisfy the requirements for the adaptive controller to have guaranteed convergence and bounded gains. This paper will be divided into two parts. Here in Part I we will review the basic adaptive control approach and introduce the primary ideas. In Part II, we will present the RMF methodology and complete the proofs of all our results. Also, we will apply the above theoretical results to a simple flexible structure example to illustrate the behavior with and without the residual mode filter.

Distribution and migration of pesticide residues in mosquito control impoundments St. Lucie County, Florida, USA

Science.gov (United States)

Parkinson, R. W.; Wang, T. C.; White, J. R.; David, J. R.; Hoffman, M. E.

1993-09-01

This project was designed to: (1) document the distribution and migration of organochlorine pesticide residues within marsh substrates of 18 St. Lucie County mosquito control impoundments located along the Indian River Lagoon estuary, and (2) evaluate the impact of water management techniques on residue mobility. Our results indicate that detectible concentrations of organochlorine compounds, applied between the late 1940s and early 1950s, are present in 16 of the 18 St. Lucie County mosquito control impoundments. These compounds are primarily restricted to the surficial, organic-rich wetland sediment, which, based upon geotechnical analysis, was exposed to the atmosphere at a time when the impoundments were subjected to pesticide treatment. Contaminated sediments are present below the surficial, organic-rich layer, suggesting that some vertical migration of pesticides has occurred. It is unlikely that leaching associated with the downward percolation of impounded water was responsible for this migration as pesticide residues were never detected within the in situ pore waters. An alternative explanation is that biological processes (e.g., rooting, burrowing) facilitated the downward flux of organochlorine compounds into sediment horizons not subjected to direct treatment. Eighty-eight surface water samples obtained from two impoundments subjected to contrasting water management techniques were analyzed for pesticide content. None of the surficial water samples collected in association with these impoundments contained detectible concentrations of organochlorine compounds. These samples were unfiltered and contained as much as 25 mg/1 of particulate organic matter. This suggests that the currently preferred management technique (RIM), which is designed to maintain water quality, limit mosquito production, and provide for ecological continuity, does not hydraulically mobilize pesticide residues into the Indian River Lagoon estuary.

Tank 12H residuals sample analysis report

Energy Technology Data Exchange (ETDEWEB)

Oji, L. N. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Shine, E. P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Diprete, D. P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Coleman, C. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hay, M. S. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-06-11

The Savannah River National Laboratory (SRNL) was requested by Savannah River Remediation (SRR) to provide sample preparation and analysis of the Tank 12H final characterization samples to determine the residual tank inventory prior to grouting. Eleven Tank 12H floor and mound residual material samples and three cooling coil scrape samples were collected and delivered to SRNL between May and August of 2014.

Controlling BWR pipe cracking by residual stress modification

International Nuclear Information System (INIS)

Gilman, J.D.; Giannuzzi, A.J.; Childs, W.J.

1983-01-01

Intergranular stress corrosion cracking may occur in the weld heat-affected zone of susceptible stainless steel materials which have been used in some boiling water reactor piping systems. One of the prerequisite conditions for stress corrosion attack is a high tensile stress in the exposed, locally sensitized material near the weld root. Several processes have been developed which can deter stress corrosion attack by altering the residual stress distributions near the welds to ensure that low stresses prevail in critical locations. These residual stress modification remedies and their qualification testing are described in this paper. (author)

Landfilling of waste incineration residues

DEFF Research Database (Denmark)

Christensen, Thomas Højlund; Astrup, Thomas; Cai, Zuansi

2002-01-01

Residues from waste incineration are bottom ashes and air-pollution-control (APC) residues including fly ashes. The leaching of heavy metals and salts from the ashes is substantial and a wide spectrum of leaching tests and corresponding criteria have been introduced to regulate the landfilling...

A logging residue "yield" table for Appalachian hardwoods

Science.gov (United States)

A. Jeff Martin

1976-01-01

An equation for predicting logging-residue volume per acre for Appalachian hardwoods was developed from data collected on 20 timber sales in national forests in West Virginia and Virginia. The independent variables of type-of-cut, products removed, basal area per acre, and stand age explained 95 percent of the variation in residue volume per acre. A "yield"...

Opportunities and Barriers to Resource Recovery and Recycling from Shredder Residue in the United States

Science.gov (United States)

Nayak, Naren; Apelian, Diran

2014-11-01

Shredder residue is the by-product remaining after ferrous and nonferrous metals have been recovered from the processing of vehicles, white goods, and peddler scrap. Shredder residue consists of glass, plastics, rubber, dirt, and small amounts of metal. It is estimated that 5-7 million tons of this shredder residue are landfilled each year in the United States. Technical advancements, coupled with European Union directives and the economic climate, have transformed the recycling of shredder residue in Europe. In the United States, however, regulatory controls and the cheap cost of landfill have worked against the advancement of recycling and recovery of this resource. The Argonne National Laboratory, which is funded by the U.S. Department of Energy, has investigated the effectiveness of recycling shredder residue into polymers. Other research has examined the use of shredder residue in waste-to-energy applications. To improve our ability to process and recycle shredder residue, an investigation of the regulatory, economic, and technological challenges was undertaken. The objective was to conduct a comprehensive review of work done to date, to document the composition of typical shredder output and to identify potential recoverable items (residual metals, plastics, rubber, foam, etc.). Along with uncovering potential new markets, the research would identify the technical, regulatory, and economic barriers to developing those markets.

Control of postharvest diseases of fruit by heat and fungicides: efficacy, residue levels, and residue persistence. A review.

Science.gov (United States)

Schirra, Mario; D'Aquino, Salvatore; Cabras, Paolo; Angioni, Alberto

2011-08-24

Extensive research has been done in recent years to reduce the heavy dependence on chemical fungicides to control postharvest diseases and disorders of horticultural crops. Alternative strategies were based on improved cultural practices, biological control, plant-defense promoters, and physical treatments such as UV illumination, radiofrequency treatment, heat therapy, and storage technologies. Among these, postharvest heat treatments such as hot water dips, short hot water rinsing and brushing, and hot air conditioning have reduced rot development and enhanced fruit resistance to chilling injury in sensitive cultivars while retaining fruit quality during cold storage and shelf life. Additive or synergistic increases in effectiveness were observed by integrating heat therapy with various chemical compounds, thus leading to significant reductions in the application of active ingredients to protect produce from decay. This paper highlights the knowledge on this topic with emphasis on heat therapy effects and factors affecting the uptake, persistence, and performance of fungicide residues when they are applied in combination with hot water.

U.S. Isostatic Residual Gravity Grid

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — isores.bin - standard grid containing isostatic residual gravity map for U.S. Grid interval = 4 km. Projection is Albers (central meridian = 96 degrees West; base...

Properties of sintered glass-ceramics prepared from plasma vitrified air pollution control residues

Energy Technology Data Exchange (ETDEWEB)

Roether, J.A.; Daniel, D.J. [Department of Materials, Imperial College London, London SW7 2AZ (United Kingdom); Amutha Rani, D. [Department of Materials, Imperial College London, London SW7 2AZ (United Kingdom); Department of Civil and Environmental Engineering, Imperial College London, London SW7 2AZ (United Kingdom); Deegan, D.E. [Tetronics Ltd., Swindon, Wiltshire SN3 4DE (United Kingdom); Cheeseman, C.R., E-mail: c.cheeseman@imperial.ac.uk [Department of Civil and Environmental Engineering, Imperial College London, London SW7 2AZ (United Kingdom); Boccaccini, A.R., E-mail: a.boccaccini@imperial.ac.uk [Department of Materials, Imperial College London, London SW7 2AZ (United Kingdom)

2010-01-15

Air pollution control (APC) residues, obtained from a major UK energy from waste (EfW) plant, processing municipal solid waste, have been blended with silica and alumina and melted using DC plasma arc technology. The glass produced was crushed, milled, uni-axially pressed and sintered at temperatures between 750 and 1150 deg. C, and the glass-ceramics formed were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Mechanical properties assessed included Vickers's hardness, flexural strength, Young's modulus and thermal shock resistance. The optimum sintering temperature was found to be 950 deg. C. This produced a glass-ceramic with high density ({approx}2.58 g/cm{sup 3}), minimum water absorption ({approx}2%) and relatively high mechanical strength ({approx}81 {+-} 4 MPa). Thermal shock testing showed that 950 deg. C sintered samples could withstand a 700 deg. C quench in water without micro-cracking. The research demonstrates that glass-ceramics can be readily formed from DC plasma treated APC residues and that these have comparable properties to marble and porcelain. This novel approach represents a technically and commercially viable treatment option for APC residues that allow the beneficial reuse of this problematic waste.

Inventory of sites used to develop residual radioactivity criteria

International Nuclear Information System (INIS)

Ronca-Battista, M.; Hardeman, J.C. Jr.

1986-01-01

The US Environmental Protection Agency (EPA), in conjunction with the National Conference of Radiation Control Program Directors (CRCPD), has compiled an inventory of never licensed or otherwise poorly documented sites that may be contaminated with radioactive materials. This effort is in support of the EPA's development of radiation protection criteria for residual radioactivity at decommissioned sites. The inventory will help to establish the range of circumstances for which criteria are needed, as well as the suitability of candidate criteria for actual situations. The information will also be used to develop model sites and facilities for analyzing technical and economic feasibility of residual radioactivity criteria and to assess costs and benefits of alternate criteria. Relevant information about each site, such as radionuclides, waste forms, and quantities present will be included in the inventory when such information is available. The CRCPD has requested that each State radiation control agency furnish the information for the inventory. The inventory supplements the relatively extensive documentation of sites regulated by Federal or State agencies with information on old or unlicensed sites, such as old waste storage sites or radium ore processing facilities

Geodetic Control Points - National Geodetic Survey Benchmarks

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — This data contains a set of geodetic control stations maintained by the National Geodetic Survey. Each geodetic control station in this dataset has either a precise...

Indoor residual spraying with a mixture of clothianidin (a neonicotinoid insecticide and deltamethrin provides improved control and long residual activity against pyrethroid resistant Anopheles gambiae sl in Southern Benin.

Directory of Open Access Journals (Sweden)

Corine Ngufor

Full Text Available There is an urgent need for new insecticides for indoor residual spraying (IRS which can provide improved and prolonged control of malaria vectors that have developed resistance to existing insecticides. The neonicotinoid, clothianidin represents a class of chemistry new to public health. Clothianidin acts as an agonist on nicotinic acetyl choline receptors. IRS with a mixture of Clothianidin and another WHO approved insecticide such as deltamethrin could provide improved control of insecticide resistant malaria vector populations and serve as a tool for insecticide resistance management.The efficacy and residual activity of a novel IRS mixture of deltamethrin and clothianidin was evaluated against wild pyrethroid resistant An. gambiae sl in experimental huts in Cove, Benin. Two application rates of the mixture were tested and comparison was made with clothianidin and deltamethrin applied alone. To assess the residual efficacy of the treatments on different local wall substrates, the inner walls of the experimental huts were covered with either cement, mud or plywood.Clothianidin demonstrated a clear delayed expression in mortality of wild pyrethroid resistant An. gambiae sl in the experimental huts which reached its full effect 120 hours after exposure. Overall mortality over the 12-month hut trial was 15% in the control hut and 24-29% in the deltamethrin-treated huts. The mixture of clothianidin 200mg/m2 and deltamethrin 25mg/m2 induced high overall hut mortality rates (87% on mud walls, 82% on cement walls and 61% on wooden walls largely due to the clothianidin component and high hut exiting rates (67-76% mostly due to the deltamethrin component. Mortality rates remained >80% for 8-9 months on mud and cement walls. The residual activity trend was confirmed by results from monthly in situ cone bioassays with laboratory susceptible An. gambiae Kisumu strain.IRS campaigns with the mixture of clothianidin plus deltamethrin have the potential to

Indoor residual spraying with a mixture of clothianidin (a neonicotinoid insecticide) and deltamethrin provides improved control and long residual activity against pyrethroid resistant Anopheles gambiae sl in Southern Benin.

Science.gov (United States)

Ngufor, Corine; Fongnikin, Augustin; Rowland, Mark; N'Guessan, Raphael

2017-01-01

There is an urgent need for new insecticides for indoor residual spraying (IRS) which can provide improved and prolonged control of malaria vectors that have developed resistance to existing insecticides. The neonicotinoid, clothianidin represents a class of chemistry new to public health. Clothianidin acts as an agonist on nicotinic acetyl choline receptors. IRS with a mixture of Clothianidin and another WHO approved insecticide such as deltamethrin could provide improved control of insecticide resistant malaria vector populations and serve as a tool for insecticide resistance management. The efficacy and residual activity of a novel IRS mixture of deltamethrin and clothianidin was evaluated against wild pyrethroid resistant An. gambiae sl in experimental huts in Cove, Benin. Two application rates of the mixture were tested and comparison was made with clothianidin and deltamethrin applied alone. To assess the residual efficacy of the treatments on different local wall substrates, the inner walls of the experimental huts were covered with either cement, mud or plywood. Clothianidin demonstrated a clear delayed expression in mortality of wild pyrethroid resistant An. gambiae sl in the experimental huts which reached its full effect 120 hours after exposure. Overall mortality over the 12-month hut trial was 15% in the control hut and 24-29% in the deltamethrin-treated huts. The mixture of clothianidin 200mg/m2 and deltamethrin 25mg/m2 induced high overall hut mortality rates (87% on mud walls, 82% on cement walls and 61% on wooden walls) largely due to the clothianidin component and high hut exiting rates (67-76%) mostly due to the deltamethrin component. Mortality rates remained >80% for 8-9 months on mud and cement walls. The residual activity trend was confirmed by results from monthly in situ cone bioassays with laboratory susceptible An. gambiae Kisumu strain. IRS campaigns with the mixture of clothianidin plus deltamethrin have the potential to provide

Risk-based approach to developing a national residue sampling plan for testing under European Union regulation for veterinary medicinal products and coccidiostat feed additives in domestic animal production.

Science.gov (United States)

Danaher, Martin; Shanahan, Conor; Butler, Francis; Evans, Rhodri; O'Sullivan, Dan; Glynn, Denise; Camon, Tim; Lawlor, Peadar; O'Keeffe, Michael

2016-07-01

A ranking system for veterinary medicinal products and coccidiostat feed additives has been developed as a tool to be applied in a risk-based approach to the residue testing programme for foods of animal origin in the Irish National Residue Control Plan (NRCP). Three characteristics of substances that may occur as residues in food are included in the developed risk ranking system: Potency, as measured by the acceptable daily intake assigned by the European Medicines Agency Committee for Medicinal Products for Veterinary Use, to each substance; Usage, as measured by the three factors of Number of Doses, use on Individual animals or for Group treatment, and Withdrawal Period; and Residue Occurrence, as measured by the number of Non-Compliant Samples in the NRCP. For both Number of Doses and Non-Compliant Samples, data for the 5-year period 2008-12 have been used. The risk ranking system for substances was developed for beef cattle, sheep and goats, pigs, chickens and dairy cattle using a scoring system applied to the various parameters described above to give an overall score based on the following equation: Potency × Usage (Number of Doses + Individual/Group Use + Withdrawal Period) × Residue Occurrence. Applying this risk ranking system, the following substances are ranked very highly: antimicrobials such as amoxicillin (for all species except pigs), marbofloxacillin (for beef cattle), oxytetracycline (for all species except chickens), sulfadiazine with trimethoprim (for pigs and chickens) and tilmicosin (for chickens); antiparasitic drugs, such as the benzimidazoles triclabendazole (for beef and dairy cattle), fenbendazole/oxfendazole (for sheep/goats and dairy cattle) and albendazole (for dairy cattle), the avermectin ivermectin (for beef cattle), and anti-fluke drugs closantel and rafoxanide (for sheep/goats); the anticoccidials monensin, narasin, nicarbazin and toltrazuril (for chickens). The risk ranking system described is a relatively simple system

Water-controlled wealth of nations.

Science.gov (United States)

Suweis, Samir; Rinaldo, Andrea; Maritan, Amos; D'Odorico, Paolo

2013-03-12

Population growth is in general constrained by food production, which in turn depends on the access to water resources. At a country level, some populations use more water than they control because of their ability to import food and the virtual water required for its production. Here, we investigate the dependence of demographic growth on available water resources for exporting and importing nations. By quantifying the carrying capacity of nations on the basis of calculations of the virtual water available through the food trade network, we point to the existence of a global water unbalance. We suggest that current export rates will not be maintained and consequently we question the long-term sustainability of the food trade system as a whole. Water-rich regions are likely to soon reduce the amount of virtual water they export, thus leaving import-dependent regions without enough water to sustain their populations. We also investigate the potential impact of possible scenarios that might mitigate these effects through (i) cooperative interactions among nations whereby water-rich countries maintain a tiny fraction of their food production available for export, (ii) changes in consumption patterns, and (iii) a positive feedback between demographic growth and technological innovations. We find that these strategies may indeed reduce the vulnerability of water-controlled societies.

National Nuclear Management and Control Agency (NNCA)

International Nuclear Information System (INIS)

Yoon, Wan Ki

2006-01-01

The National Nuclear Management and Control Agency (NNCA) is an independent agency for safeguards and material control for nuclear activities in the Republic of Korea. Formerly subordinate to the Korea Atomic Energy Research Institute (KAERI), it is temporarily associated with the Korea Institute of Nuclear Safety (KINS). In mid-2006 it will become fully independent. The NNCA is responsible for safeguards within the ROK, cooperates with the IAEA, and supports technical needs of the Ministry of Science and Technology (MOST). In addition, it has responsibilities in export controls and physical protection. In the future the NNCA expects to become a national 'think tank' for nuclear control and nonproliferation issues. This presentation enumerated the many responsibilities of the NNCA and explained the structure and staffing of the organization. (author)

Residual efficacy of pyriproxyfen and hydroprene applied to wood, metal and concrete for control of stored-product insects.

Science.gov (United States)

Arthur, Frank H; Liu, Siwei; Zhao, Baige; Phillips, Thomas W

2009-07-01

Pyriproxyfen and hydroprene are insect growth regulators (IGRs) that have been evaluated to control insect pests of field crops, but there are limited reports of efficacy against stored-product insects. A laboratory study was conducted to determine residual efficacy of pyriproxyfen and hydroprene on wood, metal and concrete surfaces. Pyriproxyfen was applied to the surfaces at 1.15 and 2.3 mg active ingredient [AI] m(-2), while hydroprene was applied at the label rate of 19 mg AI m(-2). Late-instar larvae of Tribolium confusum Jacqueline DuVal, T. castaneum (Herbst), Oryzaephilus surinamenis L., Lasioderma serricorne (F.) and Plodia interpunctella (Hübner) were exposed with a food source on the treated surfaces. Residual testing was conducted at 1, 28 and 56 days post-treatment. Hydroprene was least persistent on concrete and generally most persistent on metal. Pyriproxyfen gave greater residual persistence than hydroprene, and there was no consistent difference in efficacy among the three surfaces. Efficacy varied among the five insect species, but generally P. interpunctella was the most tolerant species to both IGRs. Pyriproxyfen gave effective residual control of primary stored-product insect species by inhibiting adult emergence of exposed larvae. Results show that pyriproxyfen can be a useful addition for pest management programs in mills, warehouses and food storage facilities. (c) John Wiley & Sons, Ltd.

Controle de plantas daninhas em milho em função de quantidades de palha de nabo forrageiro Weed control in corn as a function of amount of turnip crop residue

Directory of Open Access Journals (Sweden)

M.A. Rizzardi

2006-06-01

Full Text Available Objetivou-se com este experimento avaliar a influência da quantidade de palha de nabo forrageiro (Raphanus sativus var. oleiferus no controle de plantas daninhas em milho. O delineamento experimental foi o de parcelas subdivididas, em blocos casualizados, com quatro repetições. Os tratamentos constaram das quantidades de 0, 6 e 9 t ha-1 de palha de nabo forrageiro, além do pousio, dispostas na parcela principal e, ainda, de seis momentos de controle de plantas daninhas (milho com 1, 2, 4, 5, 6 e 7 folhas, mais duas testemunhas (sem a presença de plantas daninhas e sem o controle destas, dispostos nas subparcelas. Houve interação de quantidades de palha e momentos de controle em relação ao grau de controle de plantas daninhas; o melhor momento ocorreu entre os estádios de duas a quatro folhas do milho. Na ausência de controle químico, o rendimento de grãos de milho foi superior no tratamento com 9 t ha-1 de palha de nabo forrageiro. O controle químico não proporcionou aumento significativo no rendimento de grãos do milho quando a quantidade de palha de nabo forrageiro foi de 9 t ha-1.The objective of this study was to evaluate the effect of the amount of turnip (Raphanus sativus var. oleiferus crop residue on weed control in corn. The experimental design was a split-plot, in randomized blocks, with four replications. The treatments tested were 0, 6, and 9 t ha-1 of turnip crop residues, fallow period (the amount of residues was equivalent to the amount of natural vegetation residues, arranged as main plots, and six weed control periods (corn plants with 1, 2, 4, 5, 6, and 7 developed leaves, besides two controls (one without weeds and another without weed control, arranged as subplots. Interactions occurred between residue amounts and control periods in relation to the degree of weed control. The best control period was achieved when the corn plants presented from 2 to 4 developed leaves. Corn grain yield was higher in the control

Occurrence and distribution study of residues from pesticides applied under controlled conditions in the field during rice processing.

Science.gov (United States)

Pareja, Lucía; Colazzo, Marcos; Pérez-Parada, Andrés; Besil, Natalia; Heinzen, Horacio; Böcking, Bernardo; Cesio, Verónica; Fernández-Alba, Amadeo R

2012-05-09

The results of an experiment to study the occurrence and distribution of pesticide residues during rice cropping and processing are reported. Four herbicides, nine fungicides, and two insecticides (azoxystrobin, byspiribac-sodium, carbendazim, clomazone, difenoconazole, epoxiconazole, isoprothiolane, kresoxim-methyl, propanil, quinclorac, tebuconazole, thiamethoxam, tricyclazole, trifloxystrobin, λ-cyhalotrin) were applied to an isolated rice-crop plot under controlled conditions, during the 2009-2010 cropping season in Uruguay. Paddy rice was harvested and industrially processed to brown rice, white rice, and rice bran, which were analyzed for pesticide residues using the original QuEChERS methodology and its citrate variation by LC-MS/MS and GC-MS. The distribution of pesticide residues was uneven among the different matrices. Ten different pesticide residues were found in paddy rice, seven in brown rice, and eight in rice bran. The highest concentrations were detected in paddy rice. These results provide information regarding the fate of pesticides in the rice food chain and its safety for consumers.

Radioactive material in residues of health services residues

International Nuclear Information System (INIS)

Costa R, A. Jr.; Recio, J.C.

2006-01-01

The work presents the operational actions developed by the one organ responsible regulator for the control of the material use radioactive in Brazil. Starting from the appearance of coming radioactive material of hospitals and clinical with services of nuclear medicine, material that that is picked up and transported in specific trucks for the gathering of residuals of hospital origin, and guided one it manufactures of treatment of residuals of services of health, where they suffer radiological monitoring before to guide them for final deposition in sanitary embankment, in the city of Sao Paulo, Brazil. The appearance of this radioactive material exposes a possible one violation of the norms that govern the procedures and practices in that sector in the country. (Author)

Genetic control of residual variance of yearling weight in Nellore beef cattle.

Science.gov (United States)

Iung, L H S; Neves, H H R; Mulder, H A; Carvalheiro, R

2017-04-01

There is evidence for genetic variability in residual variance of livestock traits, which offers the potential for selection for increased uniformity of production. Different statistical approaches have been employed to study this topic; however, little is known about the concordance between them. The aim of our study was to investigate the genetic heterogeneity of residual variance on yearling weight (YW; 291.15 ± 46.67) in a Nellore beef cattle population; to compare the results of the statistical approaches, the two-step approach and the double hierarchical generalized linear model (DHGLM); and to evaluate the effectiveness of power transformation to accommodate scale differences. The comparison was based on genetic parameters, accuracy of EBV for residual variance, and cross-validation to assess predictive performance of both approaches. A total of 194,628 yearling weight records from 625 sires were used in the analysis. The results supported the hypothesis of genetic heterogeneity of residual variance on YW in Nellore beef cattle and the opportunity of selection, measured through the genetic coefficient of variation of residual variance (0.10 to 0.12 for the two-step approach and 0.17 for DHGLM, using an untransformed data set). However, low estimates of genetic variance associated with positive genetic correlations between mean and residual variance (about 0.20 for two-step and 0.76 for DHGLM for an untransformed data set) limit the genetic response to selection for uniformity of production while simultaneously increasing YW itself. Moreover, large sire families are needed to obtain accurate estimates of genetic merit for residual variance, as indicated by the low heritability estimates (Box-Cox transformation was able to decrease the dependence of the variance on the mean and decreased the estimates of genetic parameters for residual variance. The transformation reduced but did not eliminate all the genetic heterogeneity of residual variance, highlighting

Regulation of NORM industries and NORM residues in Belgium

Energy Technology Data Exchange (ETDEWEB)

Biermans, G.; Dehandschutter, B.; Pepin, S.; Sonck, M. [Federal Agency for Nuclear Control - FANC (Belgium)

2014-07-01

In the Belgian Royal Decree of 20 July 2001, which transposed the EU Directive 96/26/EURATOM (BSS) into national legislation regarding radiation protection regulations, a list of 'work activities involving natural radiation sources' (i.e. NORM industries) was defined based on the concept described in Article 40 of the Directive. These activities are subject to declaration to the Belgian radiation protection authority (Federal Agency for Nuclear Control - FANC). The initial list was subsequently modified by a FANC decree in 2012 to reflect the increased knowledge about NORM in other industrial sectors, most of which have also been added in the recently published New Basic Safety Standards (Directive 2013/53/EURATOM). In March 2013, an additional decree was published by FANC regulating the acceptance of NORM residues by non-radioactive waste treatment facilities. This regulation was fitted within the framework described above by introducing NORM residue treatment into the existing NORM industry list. It introduces generic exemption levels above which the processing or disposal of NORM residues will be considered as a 'work activity' and submitted to declaration according to the Belgian radiation protection regulations. On basis of this declaration, specific acceptance criteria are assigned to the disposal or processing facility. FANC has published technical and methodological guides for the operators of the concerned facilities and industries to facilitate the declaration process, and has recently organized a round-table gathering both NORM industries and waste processing industries to identify the needs, uncertainties and concerns regarding the regulatory control of NORM in Belgium. Document available in abstract form only. (authors)

Mobility of organic carbon from incineration residues

International Nuclear Information System (INIS)

Ecke, Holger; Svensson, Malin

2008-01-01

Dissolved organic carbon (DOC) may affect the transport of pollutants from incineration residues when landfilled or used in geotechnical construction. The leaching of dissolved organic carbon (DOC) from municipal solid waste incineration (MSWI) bottom ash and air pollution control residue (APC) from the incineration of waste wood was investigated. Factors affecting the mobility of DOC were studied in a reduced 2 6-1 experimental design. Controlled factors were treatment with ultrasonic radiation, full carbonation (addition of CO 2 until the pH was stable for 2.5 h), liquid-to-solid (L/S) ratio, pH, leaching temperature and time. Full carbonation, pH and the L/S ratio were the main factors controlling the mobility of DOC in the bottom ash. Approximately 60 weight-% of the total organic carbon (TOC) in the bottom ash was available for leaching in aqueous solutions. The L/S ratio and pH mainly controlled the mobilization of DOC from the APC residue. About 93 weight-% of TOC in the APC residue was, however, not mobilized at all, which might be due to a high content of elemental carbon. Using the European standard EN 13 137 for determination of total organic carbon (TOC) in MSWI residues is inappropriate. The results might be biased due to elemental carbon. It is recommended to develop a TOC method distinguishing between organic and elemental carbon

U.S. national nuclear material control and accounting system

International Nuclear Information System (INIS)

Taylor, S; Terentiev, V G

1998-01-01

Issues related to nuclear material control and accounting and illegal dealing in these materials were discussed at the April 19--20, 1996 Moscow summit meeting (G7 + Russia). The declaration from this meeting reaffirmed that governments are responsible for the safety of all nuclear materials in their possession and for the effectiveness of the national control and accounting system for these materials. The Russian delegation at this meeting stated that ''the creation of a nuclear materials accounting, control, and physical protection system has become a government priority''. Therefore, in order to create a government nuclear material control and accounting system for the Russian Federation, it is critical to study the structure, operating principles, and regulations supporting the control and accounting of nuclear materials in the national systems of nuclear powers. In particular, Russian specialists have a definite interest in learning about the National Nuclear Material Control and Accounting System of the US, which has been operating successfully as an automated system since 1968

Measurement of the fluorescence of crop residues: A tool for controlling soil erosion

Science.gov (United States)

Daughtry, C. S. T.; Mcmurtrey, J. E., III; Chappelle, E. W.; Hunter, W. J.

1994-01-01

Management of crop residues, the portion of a crop left in the field after harvest, is an important conservation practice for minimizing soil erosion and for improving water quality. Quantification of crop residue cover is required to evaluate the effectiveness of conservation tillage practices. Methods are needed to quantify residue cover that are rapid, accurate, and objective. The fluorescence of crop residue was found to be a broadband phenomenon with emission maxima at 420 to 495 nm for excitations of 350 to 420 nm. Soils had low intensity broadband emissions over the 400 to 690 nm region for excitations of 300 to 600 nm. The range of relative fluorescence intensities for the crop residues was much greater than the fluorescence observed of the soils. As the crop residues decompose their blue fluorescence values approach the fluorescence of the soil. Fluorescence techniques are concluded to be less ambiguous and better suited for discriminating crop residues and soils than reflectance methods. If properly implemented, fluorescence techniques can be used to quantify, not only crop residue cover, but also photosynthetic efficiency in the field.

Dissipation pattern of flubendiamide residues on capsicum fruit (Capsicum annuum L.) under field and controlled environmental conditions.

Science.gov (United States)

Buddidathi, Radhika; Mohapatra, Soudamini; Siddamallaiah, Lekha; Manikrao, Gourishankar; Hebbar, Shibara Shankara

2016-01-01

This investigation was undertaken to compare the dissipation pattern of flubendiamide in capsicum fruits under poly-house and open field after giving spray applications at the recommended and double doses of 48 g a.i. ha(-1) and 96 g a.i. ha(-1). Extraction and purification of capsicum fruit samples were carried out by the QuEChERS method. Residues of flubendiamide and its metabolite, des-iodo flubendiamide, were analyzed by high-performance liquid chromatography-photodiode array, and confirmed by liquid chromatography-mass spectrometry/mass spectrometry. Limit of quantification of the method was 0.05 mg kg(-1), and recovery of the insecticides was in the range of 89.6-104.3%, with relative standard deviation being 4.5-11.5%. The measurement uncertainty of the analytical method was in the range of 10.7-15.7%. Initial residue deposits of flubendiamide on capsicum fruits grown under poly-house conditions were (0.977 and 1.834 mg kg(-1)) higher than that grown in the field (0.665 and 1.545 mg kg(-1)). Flubendiamide residues persisted for 15 days in field-grown and for 25 days in poly-house-grown capsicum fruits. The residues were degraded with the half-lives of 4.3-4.7 and 5.6-6.6 days in field and poly-house respectively. Des-iodo flubendiamide was not detected in capsicum fruits or soil. The residues of flubendiamide degraded to below the maximum residue limit notified by Codex Alimentarius Commission (FAO/WHO) after 1 and 6 days in open field, and 3 and 10 days in poly-house. The results of the study indicated that flubendiamide applied to capsicum under controlled environmental conditions required longer pre-harvest interval to allow its residues to dissipate to the safe level.

An estimation of cogeneration potential by using refinery residuals in Mexico

International Nuclear Information System (INIS)

Marin-Sanchez, J.E.; Rodriguez-Toral, M.A.

2007-01-01

Electric power generation in Mexico is mainly based on fossil fuels, specifically heavy fuel oil, although the use of natural gas combined cycles (NGCC) is becoming increasingly important. This is the main destination that has promoted growing imports of natural gas, currently accounting for about 20% of the total national annual consumption. Available crude oil is becoming heavier; thus refineries should be able to process it, and to handle greater quantities of refinery residuals. If all refinery residuals are used in cogeneration plants serving petroleum refineries, the high heat/power ratio of refinery needs, leads to the availability of appreciable quantities of electricity that can be exported to the public utility. Thus, in a global perspective, Mexican imports of natural gas may be reduced by cogeneration using refinery residuals. This is not the authors' idea; in fact, PEMEX, the national oil company, has been entitled by the Mexican congress to sell its power leftovers to The Federal Electricity Commission (CFE) in order to use cogeneration in the way described for the years to come. A systematic way of determining the cogeneration potential by using refinery residuals from Mexican refineries is presented here, taking into account residual quantities and composition, from a national perspective, considering expected scenarios for Maya crude content going to local refineries in the years to come. Among different available technologies for cogeneration using refinery residuals, it is believed that the integrated gasification combined cycle (IGCC) would be the best option. Thus, considering IGCC plants supplying heat and power to refineries where it is projected to have refinery residuals for cogeneration, the expected electric power that can be sent to the public utility is quantified, along with the natural gas imports mitigation that may be attained. This in turn would contribute to a necessary fuel diversification policy balancing energy, economy and

National Drug Control Strategy. Update.

Science.gov (United States)

Office of National Drug Control Policy, Washington, DC.

President Bush's new National Drug Control Strategy for 2003 focuses on three core priorities: stopping drug use before it starts; healing America's drug users; and disrupting the market. The 2003 strategy reports progress toward meeting the President's goals of reducing drug use by 10 percent over 2 years, and 25 percent over 5 years. With regard…

Modern bioenergy from agricultural and forestry residues in Cameroon: Potential, challenges and the way forward

International Nuclear Information System (INIS)

Ackom, Emmanuel K.; Alemagi, Dieudonne; Ackom, Nana B.; Minang, Peter A.; Tchoundjeu, Zac

2013-01-01

Environmentally benign modern bioenergy is widely acknowledged as a potential substitute for fossil fuels to offset the human dependence on fossil fuels for energy. We have profiled Cameroon, a country where modern bioenergy remains largely untapped due to a lack of availability of biomass data and gaps in existing policies. This study assessed the biomass resource potential in Cameroon from sustainably extracted agricultural and forest residues. We estimated that environmentally benign residues amount to 1.11 million bone dry tons per year. This has the potential to yield 0.12–0.32 billion liters of ethanol annually to displace 18–48% of the national consumption of gasoline. Alternatively, the residues could provide 0.08–0.22 billion liters of biomass to Fischer Tropsch diesel annually to offset 17–45% of diesel fuel use. For the generation of bioelectricity, the residues could supply 0.76–2.02 TW h, which is the equivalent of 15–38% of Cameroon's current electricity consumption. This could help spread electricity throughout the country, especially in farming communities where the residues are plentiful. The residues could, however, offset only 3% of the national consumption of traditional biomass (woodfuel and charcoal). Policy recommendations that promote the wider uptake of modern bioenergy applications from residues are provided. - Highlights: • Environmentally benign residues amount to 1.11×10 6 bone dry tonnes per annum. • 0.12–0.32 billion litres of bio ethanol annually to displace 18–48% national gasoline use. • 0.08–0.22 billion litres of biomass to BTL diesel per year to offset 17–45% of diesel use. • 0.76–2.02 TW h of electricity, representing 15–38% of Cameroon's consumption. • Residues could offset only 3% of national consumption of traditional biomass

Effectiveness of control strategies against Botrytis cinerea in vineyard and evaluation of the residual fungicide concentrations.

Science.gov (United States)

Gabriolotto, Chiara; Monchiero, Matteo; Negre, Michele; Spadaro, Davide; Gullino, Maria Lodovica

2009-05-01

This investigation was undertaken to test different control strategies against Botrytis cinerea vineyards. Two commercial vineyards, "Barbera" and "Moscato," located in Piedmont (Northern Italy) were divided into seven plots and treated with different combinations of fungicides including fenhexamid, pyrimethanil, fludioxonil + cyprodinil, iprodione, and boscalid, a new carboxamide compound. An integrated strategy including a chemical (pyrimethanil) and a biocontrol agent (Trichoderma spp. t2/4ph1) was also included. At harvest, the percentage of bunches and berries attacked by B. cinerea and the concentration of the chemical fungicides were determined. All the pesticide residues at harvest were below the maximum residue level (MRL), except when two applications of pyrimethanil per season were applied. Boscalid was the most effective active ingredient against B. cinerea among the tested chemicals. When boscalid application was followed by a treatment with pyrimethanil, its efficacy was similar to that shown by two treatments of pyrimethanil. However, this second strategy was not feasible due to the risks of resistance development in the pathogen and to the residue accumulation as indicated by the analysis.

Residual nilpotence and residual solubility of groups

International Nuclear Information System (INIS)

Mikhailov, R V

2005-01-01

The properties of the residual nilpotence and the residual solubility of groups are studied. The main objects under investigation are the class of residually nilpotent groups such that each central extension of these groups is also residually nilpotent and the class of residually soluble groups such that each Abelian extension of these groups is residually soluble. Various examples of groups not belonging to these classes are constructed by homological methods and methods of the theory of modules over group rings. Several applications of the theory under consideration are presented and problems concerning the residual nilpotence of one-relator groups are considered.

A study on the production of agricultural residues in Italy

Energy Technology Data Exchange (ETDEWEB)

Di Blasi, C.; Tanzi, V.; Lanzetta, M. [Universita degli Studi di Napoli Federico II, Dip di Ingegneria Chimica, Napoli (Italy)

1997-12-01

The Italian production of agricultural residues has been evaluated with a view to energy recovery through gasification. Two main categories of residues have been identified: the first, (A) is associated with the growing and collection of products with a nutritional value, whereas the second (B) includes the residues associated with the subsequent processing in order to obtain final products for commercialization. Category A, which comprises three further sub-categories: straw (A1); woody residues (A2); and stems and leaves (residues from vegetables, tobacco, sugar beet, (A3)), results in about 16.5 mt yr. The average amount of straw (A1) is 11 mt/yr, of which about 60% is waste to be eliminated. Woody residues (A2) (mainly pruning off-cuts from vineyards and olive groves) are about 3.5 mt/yr (85% unused). Category A3 amounts to about 2 mt/yr (90% unused). Straw is available mainly in the northern part of the country, whereas the other two sub-categories are widely distributed in central and southern regions. The yields of category B are estimated at 4 mt/yr, of which more than 3 mt/yr are waste products from grape and olive processing. Other residues, such as rice, sunflower and soya-bean husks (about 0.65 mt/yr), almond and nut shells and fruit stones (about 0.2 mt/yr), although not widely available on a national scale, can be significant on a local basis. The total amount of unused agricultural residues is about 14.5 mt/yr, which, if completely exploited through gasification, can contribute as much as 7-10% to the current national electricity needs. The regions of Veneto, Puglia, Friuli, Lombardia and Emilia Romagna appear to be good candidates for electricity production, given the significant surface concentration of unused residues (105-55 t km{sup 2}). (author)

Evaluation of Residue Based Power Oscillation Damping Control of Inter-area Oscillations for Static Power Sources

DEFF Research Database (Denmark)

Adamczyk, Andrzej Grzegorz; Teodorescu, Remus; Iov, Florin

2012-01-01

Low frequency inter-area oscillations are known stability issue of large interconnected electrical grids. It was demonstrated that additional control loop can be applied for static power sources, like FACTS, HVDC or modern Wind Power Plants, to modulate their power output and successfully attenuate......, it is proposed to give more attention to additional indices like transfer function zero location and interactions between mode of interest and other system dynamics. Consequently, additional rules are proposed for residue based damping control design....

Index of tobacco control sustainability (ITCS): a tool to measure the sustainability of national tobacco control programmes.

Science.gov (United States)

Jackson-Morris, Angela; Latif, Ehsan

2017-03-01

To produce a tool to assess and guide sustainability of national tobacco control programmes. A two-stage process adapting the Delphi and Nominal group techniques. A series of indicators of tobacco control sustainability were identified in grantee/country advisor reports to The International Union Against Tuberculosis and Lung Disease under the Bloomberg Initiative to Reduce Tobacco Control (2007-2015). Focus groups and key informant interviews in seven low and middle-income countries (52 government and civil society participants) provided consensus ratings of the indicators' relative importance. Data were reviewed and the indicators were accorded relative weightings to produce the 'Index of Tobacco Control Sustainability' (ITCS). All 31 indicators were considered 'Critical' or 'Important' by the great majority of participants. There was consensus that a tool to measure progress towards tobacco control sustainability was important. The most critical indicators related to financial policies and allocations, a national law, a dedicated national tobacco control unit and civil society tobacco control network, a national policy against tobacco industry 'Corporate Social Responsibility' (CSR), national mortality and morbidity data, and national policy evaluation mechanisms. The 31 indicators were agreed to be 'critical' or 'important' factors for tobacco control sustainability. The Index comprises the weighted indicators as a tool to identify aspects of national tobacco control programmes requiring further development to augment their sustainability and to measure and compare progress over time. The next step is to apply the ITCS and produce tobacco control sustainability assessments. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Detection of antibiotic residues in food by Charm II test

International Nuclear Information System (INIS)

Addali, Mohamed

2014-01-01

Antibiotics are used in food to: -therapy and prophylaxis, -increase the productivity of the food producing animals. The presence of antimicrobial residues: -constitutes a potential human health hazard. has significant impact on international food trade. has implications on technological process in dairy industry. Detection of antibiotic residues is of great interest. It helps protect humans against the effects of such residues, the more it can support the participation of our country in international trade. Charm II test is one of the methods of detection of antimicrobial residues. The tests utilize microbial or antibody receptor assay technology. The sample is incubated with a binding agent (microbial cells with specific receptor sites or with specific antibodies attached) and a tracer (the radio-labeled version of the antibiotic to be detected). The amount of tracer on the binding agent is measured using a scintillation counter and is compared to a pre-determined cut-off or control point. If contaminating antibiotic is present, it will prevent the binding of the tracer by occupying the receptors on the binding agent. The less labeled tracer detected, the more contaminating antibiotic there is present in the sample. This work, carried out at the Radiochemical Laboratory of the National Centre of Nuclear Science and Technology, has two parts: 1/ The first is reserved to a literature review provides an overview on antibiotics and the charm II method. 2/ The second is devoted to the experimental study and presentation of results.

Residual infestation and recolonization during urban Triatoma infestans Bug Control Campaign, Peru.

Science.gov (United States)

Barbu, Corentin M; Buttenheim, Alison M; Pumahuanca, Maria-Luz Hancco; Calderón, Javier E Quintanilla; Salazar, Renzo; Carrión, Malwina; Rospigliossi, Andy Catacora; Chavez, Fernando S Malaga; Alvarez, Karina Oppe; Cornejo del Carpio, Juan; Náquira, César; Levy, Michael Z

2014-12-01

Chagas disease vector control campaigns are being conducted in Latin America, but little is known about medium-term or long-term effectiveness of these efforts, especially in urban areas. After analyzing entomologic data for 56,491 households during the treatment phase of a Triatoma infestans bug control campaign in Arequipa, Peru, during 2003-2011, we estimated that 97.1% of residual infestations are attributable to untreated households. Multivariate models for the surveillance phase of the campaign obtained during 2009-2012 confirm that nonparticipation in the initial treatment phase is a major risk factor (odds ratio [OR] 21.5, 95% CI 3.35-138). Infestation during surveillance also increased over time (OR 1.55, 95% CI 1.15-2.09 per year). In addition, we observed a negative interaction between nonparticipation and time (OR 0.73, 95% CI 0.53-0.99), suggesting that recolonization by vectors progressively dilutes risk associated with nonparticipation. Although the treatment phase was effective, recolonization in untreated households threatens the long-term success of vector control.

Indoor residual spraying with a mixture of clothianidin (a neonicotinoid insecticide) and deltamethrin provides improved control and long residual activity against pyrethroid resistant Anopheles gambiae sl in Southern Benin.

OpenAIRE

Ngufor, C; Fongnikin, A; Rowland, M; N'Guessan, R

2017-01-01

There is an urgent need for new insecticides for indoor residual spraying (IRS) which can provide improved and prolonged control of malaria vectors that have developed resistance to existing insecticides. The neonicotinoid, clothianidin represents a class of chemistry new to public health. Clothianidin acts as an agonist on nicotinic acetyl choline receptors. IRS with a mixture of Clothianidin and another WHO approved insecticide such as deltamethrin could provide improved control of insectic...

Efficacy of insecticides in fruit borer control and residues on sugar apple fruit

Directory of Open Access Journals (Sweden)

Alessandro da Silva Oliveira

Full Text Available ABSTRACT Bahia is the Brazilian state with the largest production of sugar apple fruits (Annona squamosa L., and fruit borer (Cerconota anonella, Sepp. 1830 is a key crop pest. Insecticides are the main strategy for pest control even though there are no pesticides registered for this crop. This study aimed to assess the efficacy of insecticides to control fruit borer and determine the levels of insecticide residues in sugar apple fruits aiming at requesting the extension of authorization to use insecticide products in this crop. The experiment was conducted in an eight-year-old irrigated orchard (2 × 4 m located in Anagé, Bahia, Brazil. The experimental design was a randomized block design with 10 treatments (three insecticides with three doses and a control with water and 5 replications. Each plot was composed of four plants but only the two central ones were assessed. Insecticides and doses (g a.i. 100 L−1 water were Bacillus thuringiensis: 0.8, 1.7, and 2.5; triflumuron: 2.4, 3.6, and 4.8; and imidacloprid: 4.0, 10.0, and 16.0. Nine sprayings were carried out at fortnightly intervals with a costal sprayer with constant pressure, JA-2 nozzle, and with jet directed to the fruits. Ten assessments were performed in order to observe fruit borer presence in 30 previously marked fruits per plot. Imidacloprid, at the highest studied dose, was the only effective treatment. Analyses of imidacloprid residues, at 21 and 30 days after the highest dose application, indicated levels higher than the maximum limit allowed. Insecticides under the conditions tested do not meet the norms for requesting the extension of authorization to use insecticides for citrus in sugar apple fruits.

Focus on agricultural residues: Microstructure of almond hull (abstract)

Science.gov (United States)

Agricultural residues have historically been used as animal feed or burned for disposal. These residues, therefore, have little economic value and may end up becoming disposal problems because tighter air quality control measures may limit burning of the residues. Therefore, value-added products mad...

Element composition and mineralogical characterisation of air pollution control residue from UK energy-from-waste facilities

Energy Technology Data Exchange (ETDEWEB)

Bogush, Anna [Centre for Resource Efficiency & the Environment (CREE), Department of Civil, Environmental & Geomatic Engineering (CEGE), University College London UCL, Chadwick Building, Gower Street, London WC1E 6BT (United Kingdom); Stegemann, Julia A., E-mail: j.stegemann@ucl.ac.uk [Centre for Resource Efficiency & the Environment (CREE), Department of Civil, Environmental & Geomatic Engineering (CEGE), University College London UCL, Chadwick Building, Gower Street, London WC1E 6BT (United Kingdom); Wood, Ian [Department of Earth Sciences, University College London UCL, Gower Street, London WC1E 6BT (United Kingdom); Roy, Amitava [J. Bennett Johnston, Sr., Center for Advanced Microstructures & Devices, Louisiana State University, 6980 Jefferson Hwy, Baton Rouge, LA 70806 (United States)

2015-02-15

Highlights: • 66 elements, including “critical strategic elements” were determined in UK EfW APC residues. • Metal pollutants (Zn, Pb, As, Cd, Cu, Mo, Sb, Sn, Se, Ag and In) are enriched in APC residues. • Metal pollutants were widely associated with fine deposits of highly soluble CaCl{sub x}OH{sub 2−x}. • Specific metal (Zn, Pb, Cu)-bearing minerals were also detected in APC residues. - Abstract: Air pollution control (APC) residues from energy-from-waste (EfW) are alkaline (corrosive) and contain high concentrations of metals, such as zinc and lead, and soluble salts, such as chlorides and sulphates. The EPA 3050B-extractable concentrations of 66 elements, including critical elements of strategic importance for advanced electronics and energy technologies, were determined in eight APC residues from six UK EfW facilities. The concentrations of Ag (6–15 mg/kg) and In (1–13 mg/kg), as well as potential pollutants, especially Zn (0.26–0.73 wt.%), Pb (0.05–0.2 wt.%), As, Cd, Cu, Mo, Sb, Sn and Se were found to be enriched in all APC residues compared to average crustal abundances. Results from a combination of scanning electron microscopy with energy dispersive X-ray spectroscopy and also powder X-ray diffraction, thermal analysis and Fourier transform infrared spectroscopy give an exceptionally full understanding of the mineralogy of these residues, which is discussed in the context of other results in the literature. The present work has shown that the bulk of the crystalline phases present in the investigated APC residues include Ca-based phases, such as CaCl{sub x}OH{sub 2−x}, CaCO{sub 3}, Ca(OH){sub 2}, CaSO{sub 4}, and CaO, as well as soluble salts, such as NaCl and KCl. Poorly-crystalline aragonite was identified by FTIR. Sulphur appears to have complex redox speciation, presenting as both anhydrite and hannebachite in some UK EfW APC residues. Hazardous elements (Zn and Pb) were widely associated with soluble Ca- and Cl-bearing phases

Bio-electrospraying and droplet-based microfluidics: control of cell numbers within living residues

Energy Technology Data Exchange (ETDEWEB)

Hong Jongin; DeMello, Andrew J [Nanostructured Materials and Devices Group, Department of Chemistry, Imperial College London, Exhibition Road, London SW7 2AZ (United Kingdom); Jayasinghe, Suwan N, E-mail: a.demello@imperial.ac.u, E-mail: s.jayasinghe@ucl.ac.u [BioPhysics Group, Department of Mechanical Engineering, University College London, Torrington Place, London WC1E 7JE (United Kingdom)

2010-04-15

Bio-electrospraying (BES) has demonstrated great promise as a rapidly evolving strategy for tissue engineering and regenerative biology/medicine. Since its discovery in 2005, many studies have confirmed that cells (immortalized, primary and stem cells) and whole organisms (Danio rerio, Xenopus tropicalis, Caenorhabditis elegans to Drosophila) remain viable post-bio-electrospraying. Although this bio-protocol has achieved much, it suffers from one crucial problem, namely the ability to precisely control the number of cells within droplets and or encapsulations. If overcome, BES has the potential to become a high-efficiency biotechnique for controlled cell encapsulation, a technique most useful for a wide range of applications in biology and medicine ranging from the forming of three-dimensional cultures to an approach for treating diseases such as type I diabetes. In this communication, we address this issue by demonstrating the coupling of BES with droplet-based microfluidics for controlling live cell numbers within droplets and residues. (communication)

Bio-electrospraying and droplet-based microfluidics: control of cell numbers within living residues

International Nuclear Information System (INIS)

Hong Jongin; DeMello, Andrew J; Jayasinghe, Suwan N

2010-01-01

Bio-electrospraying (BES) has demonstrated great promise as a rapidly evolving strategy for tissue engineering and regenerative biology/medicine. Since its discovery in 2005, many studies have confirmed that cells (immortalized, primary and stem cells) and whole organisms (Danio rerio, Xenopus tropicalis, Caenorhabditis elegans to Drosophila) remain viable post-bio-electrospraying. Although this bio-protocol has achieved much, it suffers from one crucial problem, namely the ability to precisely control the number of cells within droplets and or encapsulations. If overcome, BES has the potential to become a high-efficiency biotechnique for controlled cell encapsulation, a technique most useful for a wide range of applications in biology and medicine ranging from the forming of three-dimensional cultures to an approach for treating diseases such as type I diabetes. In this communication, we address this issue by demonstrating the coupling of BES with droplet-based microfluidics for controlling live cell numbers within droplets and residues. (communication)

Long-term stabilization of crop residues and soil organic carbon affected by residue quality and initial soil pH.

Science.gov (United States)

Wang, Xiaojuan; Butterly, Clayton R; Baldock, Jeff A; Tang, Caixian

2017-06-01

Residues differing in quality and carbon (C) chemistry are presumed to contribute differently to soil pH change and long-term soil organic carbon (SOC) pools. This study examined the liming effect of different crop residues (canola, chickpea and wheat) down the soil profile (0-30cm) in two sandy soils differing in initial pH as well as the long-term stability of SOC at the amended layer (0-10cm) using mid-infrared (MIR) and solid-state 13 C nuclear magnetic resonance (NMR) spectroscopy. A field column experiment was conducted for 48months. Chickpea- and canola-residue amendments increased soil pH at 0-10cm in the Podzol by up to 0.47 and 0.36units, and in the Cambisol by 0.31 and 0.18units, respectively, at 48months when compared with the non-residue-amended control. The decomposition of crop residues was greatly retarded in the Podzol with lower initial soil pH during the first 9months. The MIR-predicted particulate organic C (POC) acted as the major C sink for residue-derived C in the Podzol. In contrast, depletion of POC and recovery of residue C in MIR-predicted humic organic C (HOC) were detected in the Cambisol within 3months. Residue types showed little impact on total SOC and its chemical composition in the Cambisol at 48months, in contrast to the Podzol. The final HOC and resistant organic C (ROC) pools in the Podzol amended with canola and chickpea residues were about 25% lower than the control. This apparent priming effect might be related to the greater liming effect of these two residues in the Podzol. Copyright © 2017 Elsevier B.V. All rights reserved.

Alternative treatments for indoor residual spraying for malaria control in a village with pyrethroid- and DDT-resistant vectors in The Gambia

NARCIS (Netherlands)

Tangena, J.A.A.; Adiamoh, M.; Alessandro, D' U.; Jarju, L.; Jawara, M.; Jeffries, D.; Malik, N.; Nwakanma, D.; Kaur, H.; Takken, W.; Lindsay, S.W.; Pinder, M.

2013-01-01

Background: Malaria vector control is threatened by resistance to pyrethroids, the only class of insecticides used for treating bed nets. The second major vector control method is indoor residual spraying with pyrethroids or the organochloride DDT. However, resistance to pyrethroids frequently

The influence of electrodialytic remediation on dioxin (PCDD/PCDF) levels in fly ash and air pollution control residues.

Science.gov (United States)

Dias-Ferreira, Celia; Kirkelund, Gunvor M; Jensen, Pernille E

2016-04-01

Fly ash and Air Pollution Control (APC) residues collected from three municipal solid waste incinerators in Denmark and Greenland were treated by electrodialytic remediation at pilot scale for 8-10 h. This work presents for the first time the effect of electrodialytic treatment on polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF), and how these levels impact on the valorization options for fly ash and APC residue. PCDD/PCDF levels in the original residues ranged between 4.85 and 197 ng g(-1), being higher for the electrostatic precipitator fly ash. The toxic equivalent (TEQ) varied ten fold, ranging 0.18-2.0 ng g(-1) I-TEQ, with penta and hexa-homologs being most significant for toxicity. After the electrodialytic treatment PCDD/PCDF levels increased in the residues (between 1.4 and 2.0 times). This does not mean PCDD/PCDF were synthesized, but else that soluble materials dissolve, leaving behind the non-water soluble compounds, such as PCDD/PCDF. According to the Basel Convention, PCDD/PCDF levels in these materials is low (residue could eventually be valorized, for instance as construction material, provided end-of-waste criteria are set and that a risk assessment of individual options is carried out, including the end-of-life stage when the materials become waste again. Copyright © 2016 Elsevier Ltd. All rights reserved.

A stochastic logical system approach to model and optimal control of cyclic variation of residual gas fraction in combustion engines

International Nuclear Information System (INIS)

Wu, Yuhu; Kumar, Madan; Shen, Tielong

2016-01-01

Highlights: • An in-cylinder pressure based measuring method for the RGF is derived. • A stochastic logical dynamical model is proposed to represent the transient behavior of the RGF. • The receding horizon controller is designed to reduce the variance of the RGF. • The effectiveness of the proposed model and control approach is validated by the experimental evidence. - Abstract: In four stroke internal combustion engines, residual gas from the previous cycle is an important factor influencing the combustion quality of the current cycle, and the residual gas fraction (RGF) is a popular index to monitor the influence of residual gas. This paper investigates the cycle-to-cycle transient behavior of the RGF in the view of systems theory and proposes a multi-valued logic-based control strategy for attenuation of RGF fluctuation. First, an in-cylinder pressure sensor-based method for measuring the RGF is provided by following the physics of the in-cylinder transient state of four-stroke internal combustion engines. Then, the stochastic property of the RGF is examined based on statistical data obtained by conducting experiments on a full-scale gasoline engine test bench. Based on the observation of the examination, a stochastic logical transient model is proposed to represent the cycle-to-cycle transient behavior of the RGF, and with the model an optimal feedback control law, which targets on rejection of the RGF fluctuation, is derived in the framework of stochastic logical system theory. Finally, experimental results are demonstrated to show the effectiveness of the proposed model and the control strategy.

Determination of residual boron in thermally treated controlled-porosity glasses, by colorimetry, spectrography and isotachophoresis

International Nuclear Information System (INIS)

Dawidowicz, A.L.; Matusewicz, J.; Wysocka-Lisek, J.

1989-01-01

Controlled-porosity glasses (CPGs) are often applied as sorbents in chromatography. Besides having high thermal, chemical and mechanical resistance they are characterized by a very narrow pore-size distribution and the choice of mean pore diameter and porosity covers a wide range. In spite of these advantages, their range of use in chromatography is restricted because of their strong adsorption properties, which are connected with the presence of residual boron atoms in the porous CPG skeleton. The boron concentration on the CPG surface can be increased by proper thermal treatment. When CPGs are heated in the range 400-800 0 the residual boron atoms in the network diffuse from the bulk to the surface. The paper discusses the boron content in porous glasses of different mean pore diameters and the determination of the enrichment of boron on the GPG surface, by three independent methods: colorimetry, spectrography and isotachophoresis. (author)

Application of organic geochemistry to coastal tar residues from central California

Energy Technology Data Exchange (ETDEWEB)

Kvenvolden, K.A.; Rosenbauer, R.J.; Hostettler, F.D.; Lorenson, T.D.

2000-01-01

Tar residues are common on the Monterey Bay National Marine Sanctuary. These coastal tar residues have been washed ashore and usually occur on headlands near the high-tide line. In this study, 18 coastal tar residues were collected and analyzed to determine their carbon isotopic compositions and values of selected biomarker ratios. All of the residues have very heavy ({sup 13}C-enriched) carbon isotopic compositions spanning a narrow range ({delta}{sup 13}C = {minus}22.2 to {minus}23.4{per{underscore}thousand}), and 28,30-bisnorhopane is present in all samples. These same geochemical characteristics are found in Monterey Formation oils from which the coastal tar residues were likely derived. These coastal residues could result from natural seeps or from accidental spills. Statistically the coastal tar residues can be organized into three groups, each of which may represent different spill or seep events. Seven samples of potential local representative sources for the tar residues were examined, but none could account for the coastal tars.

Validation of a hydride generation atomic absorption spectrometry methodology for determination of mercury in fish designed for application in the Brazilian national residue control plan.

Science.gov (United States)

Damin, Isabel C F; Santo, Maria A E; Hennigen, Rosmari; Vargas, Denise M

2013-01-01

In the present study, a method for the determination of mercury (Hg) in fish was validated according to ISO/IEC 17025, INMETRO (Brazil), and more recent European recommendations (Commission Decision 2007/333/EC and 2002/657/EC) for implementation in the Brazilian Residue Control Plan (NRCP) in routine applications. The parameters evaluated in the validation were investigated in detail. The results obtained for limit of detection and quantification were respectively, 2.36 and 7.88 μg kg(-1) of Hg. While the recovery varies between 90-96%. The coefficient of variation was of 4.06-8.94% for the repeatability. Furthermore, a comparison using an external proficiency testing scheme was realized. The results of method validated for the determination of the mercury in fish by Hydride generation atomic absorption spectrometry were considered suitable for implementation in routine analysis.

Residual stresses around Vickers indents

International Nuclear Information System (INIS)

Pajares, A.; Guiberteau, F.; Steinbrech, R.W.

1995-01-01

The residual stresses generated by Vickers indentation in brittle materials and their changes due to annealing and surface removal were studied in 4 mol% yttria partially stabilized zirconia (4Y-PSZ). Three experimental methods to gain information about the residual stress field were applied: (i) crack profile measurements based on serial sectioning, (ii) controlled crack propagation in post indentation bending tests and (iii) double indentation tests with smaller secondary indents located around a larger primary impression. Three zones of different residual stress behavior are deduced from the experiments. Beneath the impression a crack free spherical zone of high hydrostatic stresses exists. This core zone is followed by a transition regime where indentation cracks develop but still experience hydrostatic stresses. Finally, in an outward third zone, the crack contour is entirely governed by the tensile residual stress intensity (elastically deformed region). Annealing and surface removal reduce this crack driving stress intensity. The specific changes of the residual stresses due to the post indentation treatments are described and discussed in detail for the three zones

Derivation of residual radioactive material guidelines for 13 radionuclides present in Operable Unit IV at Brookhaven National Laboratory, Upton, New York

International Nuclear Information System (INIS)

Faillace, E.; Nimmagadda, M.; Yu, C.

1994-12-01

Residual radioactive material guidelines for 13 radionuclides (americium-241; cobalt-60; cesium-137; europium-152, -154, and -155; plutonium-238, -239, and -240; strontium-90; and uranium-234, -235, and -238) were derived for Operable Unit (OU) IV at Brookhaven National Laboratory. This site has been identified for remedial action under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980, as amended by the Superfund Amendments and Reauthorization Act of 1986. Single-nuclide guidelines were derived on the basis of the requirement that the 50-year committed effective dose equivalent to a hypothetical individual who lives or works in the immediate vicinity of OU IV should not exceed a dose constraint of 30 mrem/yr following remedial action for the current use and plausible future use scenarios or a dose limit of 100 mrem/yr for plausible but less likely future use scenarios. The US Department of Energy (DOE) residual radioactive material guideline computer code, RESRAD, was used in this evaluation; RESRAD implements the methodology described in the DOE manual for determining residual radioactive material guidelines. Four potential scenarios were considered; each assumed that, for a period of 1,000 years following remedial action, the site would be used without radiological restrictions. The four scenarios varied with regard to the type of site use, time spent at the site, and sources of food consumed

The need to revitalize our national noise policy

Science.gov (United States)

Lang, William W.; Beranek, Leo L.

2002-05-01

At the present time, our Nation does not have a national noise policy. The Congress attempted to define one with the passage of the Noise Control Act of 1972 as follows: The Congress declares that it is the policy of the United States to promote an environment for all Americans free from noise that jeopardizes their health and welfare. The Act assigned to the Environmental Protection Agency (EPA) the role of leading Federal agency with the task of coordinating the programs of all Federal agencies relating to noise research and noise control. Ten years later (1982), all funds for noise control were withdrawn from the EPA, and today the Nation is without an effective, overall noise policy. Residual responsibility for the control of environmental and occupational noise currently rests with a dozen agencies of the Federal government, as well as State, municipal, and local authorities. But the activities of these organizations are largely uncoordinated, and the enforcement of existing noise control regulations is at best sporadic, and in some cases nonexistent. To assure our quality of life and to minimize the economic impact of potential trade barriers, a study team is recommending that a national noise policy be developed and then implemented in the immediate future.

Residual efficacy of pyriproxyfen and Hydroprene applied to wood, metal, and concrete for control of stored-product insects

Science.gov (United States)

Pyriproxyfen and hydroprene are insect growth regulators (IGRs) that have been evaluated to control insect pests of field crops, but there are limited reports of efficacy against stored-product insects. A laboratory study was conducted to determine residual efficacy of pyriproxyfen and hydroprene on...

Biofertilizer potential of residual biomass of Akk (alotropis procera (Ait.))

International Nuclear Information System (INIS)

Ahmad, N.

2016-01-01

The biofertilizer potential of residual biomass, derived from two parts that is flowers and leaves of Akk,was investigated in terms of its applications as a substrate for phyto-beneficial bacterial growth and subsequent inorganic phosphate solubilizing agent. The residual biomass was obtained after the extraction of antioxidants from the leaves and flowers of Akk using different solvent systems. The treatment with residual biomass of Akk (RBA) significantly (p<0.05) enhanced the growth of Enterobacter sp. Fs-11 and Rhizobium sp. E-11 as compared to control (without residual biomass). Maximum microbial growth in terms of optical density (0.92-1.22) was observed for residual biomass sample extracted with aqueous acetone against the control (0.58-0.68). On the other hand, maximum phosphate solubilization (589.27-611.32 mu g mL-1) was recorded for aqueous ethanol extracted residual biomass while the minimum (246.31-382.15 micro g) for aqueous acetone extracted residual biomass against the control (576.65 micro g mL-1). The present study revealed that the tested RBA can be explored as an effective bio-inoculant to supplement synthetic inorganic phosphate fertilizers. However, some appropriate in-vitro assays should be conducted to optimize and standardize the quantity and mesh size of residual biomass prior to use in biofertilizer production as carrier material. (author)

Residual stress control and design of next-generation ultra-hard gear steels

Science.gov (United States)

Qian, Yana

In high power density transmission systems, Ni-Co secondary hardening steels have shown great potential for next-generation gear applications due to their excellent strength, toughness and superior fatigue performance. Study of residual stress generation and evolution in Ferrium C61 and C67 gear steels revealed that shot peening and laser peening processes effectively produce desired beneficial residual stress in the steels for enhanced fatigue performance. Surface residual stress levels of -1.4GPa and -1.5GPa were achieved in shot peened C61 and laser peened C67, respectively, without introducing large surface roughness or defects. Higher compressive residual stress is expected in C67 according to a demonstrated correlation between attainable residual stress and material hardness. Due to the lack of appropriate shot media, dual laser peening is proposed for future peening optimization in C67. A novel non-destructive synchrotron radiation technique was implemented and applied for the first time for residual stress distribution analysis in gear steels with large composition and property gradients. Observed substantial residual stress redistribution and material microstructure change during the rolling contact fatigue screening test with extremely high 5.4GPa load indicates the unsuitability of the test as a fatigue life predictor. To exploit benefits of higher case hardness and associated residual stress, a new material and process (CryoForm70) aiming at 70Rc surface hardness was designed utilizing the systems approach based on thermodynamics and secondary hardening mechanisms. The composition design was first validated by the excellent agreement between experimental and theoretical core martensite start temperature in the prototype. A novel cryogenic deformation process was concurrently designed to increase the case martensite volume fraction from 76% to 92% for enhanced strengthening efficiency and surface hardness. High temperature vacuum carburizing was

Characterization of residual oils for biodiesel production

Directory of Open Access Journals (Sweden)

Edmilson Antonio Canesin

2014-01-01

Conclusions: The obtained results suggesting that it is possible to take advantage of these residues for biodiesel production as the obtained products were approved according to the rules established by the National Association of Petroleum (ANP; the bovine samples were the exception regarding moisture and acidity.

A Multi-Factor Analysis of Sustainable Agricultural Residue Removal Potential

Energy Technology Data Exchange (ETDEWEB)

Jared Abodeely; David Muth; Paul Adler; Eleanor Campbell; Kenneth Mark Bryden

2012-10-01

Agricultural residues have significant potential as a near term source of cellulosic biomass for bioenergy production, but sustainable removal of agricultural residues requires consideration of the critical roles that residues play in the agronomic system. Previous work has developed an integrated model to evaluate sustainable agricultural residue removal potential considering soil erosion, soil organic carbon, greenhouse gas emission, and long-term yield impacts of residue removal practices. The integrated model couples the environmental process models WEPS, RUSLE2, SCI, and DAYCENT. This study uses the integrated model to investigate the impact of interval removal practices in Boone County, Iowa, US. Residue removal of 4.5 Mg/ha was performed annually, bi-annually, and tri-annually and were compared to no residue removal. The study is performed at the soil type scale using a national soil survey database assuming a continuous corn rotation with reduced tillage. Results are aggregated across soil types to provide county level estimates of soil organic carbon changes and individual soil type soil organic matter content if interval residue removal were implemented. Results show interval residue removal is possible while improving soil organic matter. Implementation of interval removal practices provide greater increases in soil organic matter while still providing substantial residue for bioenergy production.

Quadratic residues and non-residues selected topics

CERN Document Server

Wright, Steve

2016-01-01

This book offers an account of the classical theory of quadratic residues and non-residues with the goal of using that theory as a lens through which to view the development of some of the fundamental methods employed in modern elementary, algebraic, and analytic number theory. The first three chapters present some basic facts and the history of quadratic residues and non-residues and discuss various proofs of the Law of Quadratic Reciprosity in depth, with an emphasis on the six proofs that Gauss published. The remaining seven chapters explore some interesting applications of the Law of Quadratic Reciprocity, prove some results concerning the distribution and arithmetic structure of quadratic residues and non-residues, provide a detailed proof of Dirichlet’s Class-Number Formula, and discuss the question of whether quadratic residues are randomly distributed. The text is a valuable resource for graduate and advanced undergraduate students as well as for mathematicians interested in number theory.

Characterization of Hospital Residuals

International Nuclear Information System (INIS)

Blanco Meza, A.; Bonilla Jimenez, S.

1997-01-01

The main objective of this investigation is the characterization of the solid residuals. A description of the handling of the liquid and gassy waste generated in hospitals is also given, identifying the source where they originate. To achieve the proposed objective the work was divided in three stages: The first one was the planning and the coordination with each hospital center, in this way, to determine the schedule of gathering of the waste can be possible. In the second stage a fieldwork was made; it consisted in gathering the quantitative and qualitative information of the general state of the handling of residuals. In the third and last stage, the information previously obtained was organized to express the results as the production rate per day by bed, generation of solid residuals for sampled services, type of solid residuals and density of the same ones. With the obtained results, approaches are settled down to either determine design parameters for final disposition whether for incineration, trituration, sanitary filler or recycling of some materials, and storage politics of the solid residuals that allow to determine the gathering frequency. The study concludes that it is necessary to improve the conditions of the residuals handling in some aspects, to provide the cleaning personnel of the equipment for gathering disposition and of security, minimum to carry out this work efficiently, and to maintain a control of all the dangerous waste, like sharp or polluted materials. In this way, an appreciable reduction is guaranteed in the impact on the atmosphere. (Author) [es

Residual Infestation and Recolonization during Urban Triatoma infestans Bug Control Campaign, Peru1

Science.gov (United States)

Buttenheim, Alison M.; Pumahuanca, Maria-Luz Hancco; Calderón, Javier E. Quintanilla; Salazar, Renzo; Carrión, Malwina; Rospigliossi, Andy Catacora; Chavez, Fernando S. Malaga; Alvarez, Karina Oppe; Cornejo del Carpio, Juan; Náquira, César; Levy, Michael Z.

2014-01-01

Chagas disease vector control campaigns are being conducted in Latin America, but little is known about medium-term or long-term effectiveness of these efforts, especially in urban areas. After analyzing entomologic data for 56,491 households during the treatment phase of a Triatoma infestans bug control campaign in Arequipa, Peru, during 2003–2011, we estimated that 97.1% of residual infestations are attributable to untreated households. Multivariate models for the surveillance phase of the campaign obtained during 2009–2012 confirm that nonparticipation in the initial treatment phase is a major risk factor (odds ratio [OR] 21.5, 95% CI 3.35–138). Infestation during surveillance also increased over time (OR 1.55, 95% CI 1.15–2.09 per year). In addition, we observed a negative interaction between nonparticipation and time (OR 0.73, 95% CI 0.53–0.99), suggesting that recolonization by vectors progressively dilutes risk associated with nonparticipation. Although the treatment phase was effective, recolonization in untreated households threatens the long-term success of vector control. PMID:25423045

Residues from waste incineration. Final report

Energy Technology Data Exchange (ETDEWEB)

Astrup, T.; Juul Pedersen, A.; Hyks, J.; Frandsen, F.J.

2009-08-15

The overall objective of the project was to improve the understanding of the formation and characteristics of residues from waste incineration. This was done focusing on the importance of the waste input and the operational conditions of the furnace. Data and results obtained from the project have been discussed in this report according to the following three overall parts: i) mass flows and element distribution, ii) flue gas/particle partitioning and corrosion/deposition aspects, and iii) residue leaching. This has been done with the intent of structuring the discussion while tacitly acknowledging that these aspects are interrelated and cannot be separated. Overall, it was found that the waste input composition had significant impact of the characteristics of the generated residues. A similar correlation between operational conditions and residue characteristics could not be observed. Consequently, the project recommend that optimization of residue quality should focus on controlling the waste input composition. The project results showed that including specific waste materials (and thereby also excluding the same materials) may have significant effects on the residue composition, residue leaching, aerosol and deposit formation.It is specifically recommended to minimize Cl in the input waste. Based on the project results, it was found that a significant potential for optimization of waste incineration exist. (author)

Fluorescence imaging to quantify crop residue cover

Science.gov (United States)

Daughtry, C. S. T.; Mcmurtrey, J. E., III; Chappelle, E. W.

1994-01-01

Crop residues, the portion of the crop left in the field after harvest, can be an important management factor in controlling soil erosion. Methods to quantify residue cover are needed that are rapid, accurate, and objective. Scenes with known amounts of crop residue were illuminated with long wave ultraviolet (UV) radiation and fluorescence images were recorded with an intensified video camera fitted with a 453 to 488 nm band pass filter. A light colored soil and a dark colored soil were used as background for the weathered soybean stems. Residue cover was determined by counting the proportion of the pixels in the image with fluorescence values greater than a threshold. Soil pixels had the lowest gray levels in the images. The values of the soybean residue pixels spanned nearly the full range of the 8-bit video data. Classification accuracies typically were within 3(absolute units) of measured cover values. Video imaging can provide an intuitive understanding of the fraction of the soil covered by residue.

National Geodetic Survey (NGS) Geodetic Control Stations, (Horizontal and/or Vertical Control), March 2009

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — This data contains a set of geodetic control stations maintained by the National Geodetic Survey. Each geodetic control station in this dataset has either a precise...

Soviet Cinema and State Control: Lenin's Nationalization Decree Reconsidered.

Science.gov (United States)

Kepley, Vance, Jr.

1990-01-01

Proposes a revisionist account of the immediate conditions and consequences of the 1919 Soviet cinema nationalization decree. Argues that nationalization was the least successful of a set of stop-gap measures; that it dispersed and diluted control; and that it actually retarded the growth of the film industry. (KEH)

New alternatives in the control of plagues and projections of the ICA in the handling of the residuals in agricultural products

International Nuclear Information System (INIS)

Clavijo Navarro, P.E.

1995-01-01

The strategies are described indicated by the ICA for the control of plagues and of toxic residuals of agro-chemicals in the agricultural products, with emphasis in the implementation of mechanisms like the integrated control of plagues. It stands out the paper of the bio-insecticides as alternative to the agro-chemicals use and enter these stable products they are mentioned with the help of Bacillus thuringiensis, Beauveria bassiana, Nomuraea rileyi, Metarhizium anisoplidae and Verticilium lecanni. Some implications of the presence of toxic residuals are mentioned in Colombian export fruits and the measures that have been adopted to avoid them, as well as some mechanisms adopted in the international environment with the same end. The effective legislation is indicated as for prohibition and restriction of plaguicides use

Electrodialytically treated MSWI APC residue as substitute for cement in mortar

DEFF Research Database (Denmark)

Kirkelund, Gunvor Marie; Geiker, Mette Rica; Jensen, Pernille Erland

2014-01-01

Air pollution control (APC) residues from municipal solid waste incineration (MSWI) are considered hazardous waste and need pretreatment prior to possible reuse. Here, two MSWI APC residues, from which the most mobile fraction of heavy metals and salts has been removed by carbonation and/or elect......Air pollution control (APC) residues from municipal solid waste incineration (MSWI) are considered hazardous waste and need pretreatment prior to possible reuse. Here, two MSWI APC residues, from which the most mobile fraction of heavy metals and salts has been removed by carbonation and....../or electrodialytic remediation, were used in Portland cement mortar. Mortar bars with 15 % weight replacement of cement by APC residues showed compressive strengths up to 40 MPa after 28/32 days. Heavy metal and salt leaching from both crushed and monolithic mortars with APC residues was generally similar...

21 CFR 1401.2 - The Office of National Drug Control Policy-organization and functions.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false The Office of National Drug Control Policy-organization and functions. 1401.2 Section 1401.2 Food and Drugs OFFICE OF NATIONAL DRUG CONTROL POLICY PUBLIC AVAILABILITY OF INFORMATION § 1401.2 The Office of National Drug Control Policy—organization and functions. (a) The Office of National Drug...

Effects of pulse-to-pulse residual species on discharges in repetitively pulsed discharges through packed bed reactors

Science.gov (United States)

Kruszelnicki, Juliusz; Engeling, Kenneth W.; Foster, John E.; Kushner, Mark J.

2016-09-01

Atmospheric pressure dielectric barrier discharges (DBDs) sustained in packed bed reactors (PBRs) are being investigated for conversion of toxic and waste gases, and CO2 removal. These discharges are repetitively pulsed having varying flow rates and internal geometries, which results in species from the prior pulse still being in the discharge zone at the time the following discharge pulse occurs. A non-negligible residual plasma density remains, which effectively acts as preionization. This residual charge changes the discharge properties of subsequent pulses, and may impact important PBR properties such as chemical selectivity. Similarly, the residual neutral reactive species produced during earlier pulses will impact the reaction rates on subsequent pulses. We report on results of a computational investigation of a 2D PBR using the plasma hydrodynamics simulator nonPDPSIM. Results will be discussed for air flowing though an array of dielectric rods at atmospheric pressure. The effects of inter-pulse residual species on PBR discharges will be quantified. Means of controlling the presence of residual species in the reactor through gas flow rate, pulse repetition, pulse width and geometry will be described. Comparisons will be made to experiments. Work supported by US DOE Office of Fusion Energy Science and the National Science Foundation.

Life-cycle assessment of selected management options for air pollution control residues from waste incineration.

Science.gov (United States)

Fruergaard, Thilde; Hyks, Jiri; Astrup, Thomas

2010-09-15

Based on available technology and emission data seven selected management options for air-pollution-control (APC) residues from waste incineration were evaluated by life-cycle assessment (LCA) using the EASEWASTE model. Scenarios were evaluated with respect to both non-toxicity impact categories (e.g. global warming) and toxicity related impact categories (e.g. ecotoxicity and human toxicity). The assessment addressed treatment and final placement of 1 tonne of APC residue in seven scenarios: 1) direct landfilling without treatment (baseline), 2) backfilling in salt mines, 3) neutralization of waste acid, 4) filler material in asphalt, 5) Ferrox stabilization, 6) vitrification, and 7) melting with automobile shredder residues (ASR). The management scenarios were selected as examples of the wide range of different technologies available worldwide while at the same time using realistic technology data. Results from the LCA were discussed with respect to importance of: energy consumption/substitution, material substitution, leaching, air emissions, time horizon aspects for the assessment, and transportation distances. The LCA modeling showed that thermal processes were associated with the highest loads in the non-toxicity categories (energy consumption), while differences between the remaining alternatives were small and generally considered insignificant. In the toxicity categories, all treatment/utilization options were significantly better than direct landfilling without treatment (lower leaching), although the thermal processes had somewhat higher impacts than the others options (air emissions). Transportation distances did not affect the overall ranking of the management alternatives. Copyright 2010 Elsevier B.V. All rights reserved.

Effect of soil-bound residues of malathion on microbial activities

International Nuclear Information System (INIS)

Hussain, A.; Iqbal, Z.; Asi, M.R.; Tahira, R.; Chudhary, J.A.

2001-01-01

The effect of soil-bound residues of malathion on CO/sub 2/ evolution, dehydrogenase activity and some nitrogen transformations in a loam soil was investigated under laboratory conditions. The soil samples containing bound residues arising from 10 mg g-1 of the applied malathion were mixed in equal quantity with fresh soil and compared with solvent extracted control soil without bound residues (extracted in the same way as soil containing bound residues). Another control comprising un extracted fresh soil without bound residues was also kept to study the effect of solvent extraction on the biological activity. Rate of Carbon mineralization (CO/sub 2/ evolution) was decreased in the presence of soil-bound residues of malathion. Bound residues also affected dehydrogenase activity of soil. Over 40% inhibition of dehydrogenase activity was observed after 4 days and the inhibition persisted at least for 12 days. Nitrogen mineralization was stimulated in soil containing bound residues of malathion and this stimulatory effect increased with time of incubation. Nitrification was partially inhibited in the presence of soil-bound residues of malathion. The inhibitory effect of the soil-bound residues on nitrification did not show much variation with time. The soil-bound residues did not affect denitrification rate (N/sub 2/O evolution). Nitrogen fixation (acetylene reduction) was partially inhibited in soil amended with bound residues of malathion and the inhibitory effect persisted for at least one week. In general, soil bound residues of malathion inhibited CO/sub 2/ evolution, dehydrogenase activity, nitrification and nitrogen fixation while mineralization of nitrogen was stimulated. Denitrification was not affected by the applied insecticide. (author)

Global Harmonization of Maximum Residue Limits for Pesticides.

Science.gov (United States)

Ambrus, Árpád; Yang, Yong Zhen

2016-01-13

International trade plays an important role in national economics. The Codex Alimentarius Commission develops harmonized international food standards, guidelines, and codes of practice to protect the health of consumers and to ensure fair practices in the food trade. The Codex maximum residue limits (MRLs) elaborated by the Codex Committee on Pesticide Residues are based on the recommendations of the FAO/WHO Joint Meeting on Pesticides (JMPR). The basic principles applied currently by the JMPR for the evaluation of experimental data and related information are described together with some of the areas in which further developments are needed.

Favorable Local Control From Consolidative Radiation Therapy in High-Risk Neuroblastoma Despite Gross Residual Disease, Positive Margins, or Nodal Involvement

Energy Technology Data Exchange (ETDEWEB)

Ferris, Matthew J., E-mail: mjferri@emory.edu [Department of Radiation Oncology, Emory University, Atlanta, Georgia (United States); Winship Cancer Institute, Emory University, Atlanta, Georgia (United States); Danish, Hasan [Department of Radiation Oncology, Emory University, Atlanta, Georgia (United States); Winship Cancer Institute, Emory University, Atlanta, Georgia (United States); Switchenko, Jeffrey M. [Winship Cancer Institute, Emory University, Atlanta, Georgia (United States); Department of Biostatistics and Bioinformatics, Emory University, Atlanta, Georgia (United States); Deng, Claudia [Department of Radiation Oncology, Emory University, Atlanta, Georgia (United States); Winship Cancer Institute, Emory University, Atlanta, Georgia (United States); George, Bradley A.; Goldsmith, Kelly C.; Wasilewski, Karen J.; Cash, W. Thomas [Aflac Cancer and Blood Disorders Center, Children' s Healthcare of Atlanta, Atlanta, Georgia (United States); Khan, Mohammad K.; Eaton, Bree R.; Esiashvili, Natia [Department of Radiation Oncology, Emory University, Atlanta, Georgia (United States); Winship Cancer Institute, Emory University, Atlanta, Georgia (United States)

2017-03-15

Purpose: To report the influence of radiation therapy (RT) dose and surgical pathology variables on disease control and overall survival (OS) in patients treated for high-risk neuroblastoma at a single institution. Methods and Materials: We conducted a retrospective study of 67 high-risk neuroblastoma patients who received RT as part of definitive management from January 2003 until May 2014. Results: At a median follow-up of 4.5 years, 26 patients (38.8%) failed distantly; 4 of these patients also failed locally. One patient progressed locally without distant failure. Local control was 92.5%, and total disease control was 59.5%. No benefit was demonstrated for RT doses over 21.6 Gy with respect to local relapse–free survival (P=.55), disease-free survival (P=.22), or OS (P=.72). With respect to local relapse–free survival, disease-free survival, and OS, no disadvantage was seen for positive lymph nodes on surgical pathology, positive surgical margins, or gross residual disease. Of the patients with gross residual disease, 75% (6 of 8) went on to have no evidence of disease at time of last follow-up, and the 2 patients who failed did so distantly. Conclusions: Patients with high-risk neuroblastoma in this series maintained excellent local control, with no benefit demonstrated for radiation doses over 21.6 Gy, and no disadvantage demonstrated for gross residual disease after surgery, positive surgical margins, or pathologic lymph node positivity. Though the limitations of a retrospective review for an uncommon disease must be kept in mind, with small numbers in some of the subgroups, it seems that dose escalation should be considered only in exceptional circumstances.

Determine metrics and set targets for soil quality on agriculture residue and energy crop pathways

Energy Technology Data Exchange (ETDEWEB)

Ian Bonner; David Muth

2013-09-01

There are three objectives for this project: 1) support OBP in meeting MYPP stated performance goals for the Sustainability Platform, 2) develop integrated feedstock production system designs that increase total productivity of the land, decrease delivered feedstock cost to the conversion facilities, and increase environmental performance of the production system, and 3) deliver to the bioenergy community robust datasets and flexible analysis tools for establishing sustainable and viable use of agricultural residues and dedicated energy crops. The key project outcome to date has been the development and deployment of a sustainable agricultural residue removal decision support framework. The modeling framework has been used to produce a revised national assessment of sustainable residue removal potential. The national assessment datasets are being used to update national resource assessment supply curves using POLYSIS. The residue removal modeling framework has also been enhanced to support high fidelity sub-field scale sustainable removal analyses. The framework has been deployed through a web application and a mobile application. The mobile application is being used extensively in the field with industry, research, and USDA NRCS partners to support and validate sustainable residue removal decisions. The results detailed in this report have set targets for increasing soil sustainability by focusing on primary soil quality indicators (total organic carbon and erosion) in two agricultural residue management pathways and a dedicated energy crop pathway. The two residue pathway targets were set to, 1) increase residue removal by 50% while maintaining soil quality, and 2) increase soil quality by 5% as measured by Soil Management Assessment Framework indicators. The energy crop pathway was set to increase soil quality by 10% using these same indicators. To demonstrate the feasibility and impact of each of these targets, seven case studies spanning the US are presented

Multi-country assessment of residual bio-efficacy of insecticides used for indoor residual spraying in malaria control on different surface types: results from program monitoring in 17 PMI/USAID-supported IRS countries.

Science.gov (United States)

Dengela, Dereje; Seyoum, Aklilu; Lucas, Bradford; Johns, Benjamin; George, Kristen; Belemvire, Allison; Caranci, Angela; Norris, Laura C; Fornadel, Christen M

2018-01-30

comparisons of mosquito mortality rates were then made to determine any significant differences when comparing insecticide formulation, country, year, surface type, and the source of the mosquitoes used in testing. The residual efficacy of alpha-cypermethrin ranged from 4 to 10 months (average = 6.4 months), with no reported incidents of underperformance when compared to the efficacy range provided in WHO guidelines. Deltamethrin residual efficacy results reported a range of 1 to 10 months (average = 4.9 months), with two instances of underperformance. The residual efficacy of bendiocarb ranged from 2 weeks to 7 months (average = 2.8 months) and failed to achieve proposed minimum efficacy on 14 occasions. Lastly, long-lasting pirimiphos-methyl efficacy ranged from 2 months to 9 months (average = 5.3 months), but reported 13 incidents of underperformance. Much of the data used to determine application rate and expected efficacy of insecticides approved for use in IRS programs are collected in controlled laboratory or pilot field studies. However, the generalizability of the results obtained under controlled conditions are limited and unlikely to account for variation in locally sourced housing materials, climate, and the myriad other factors that may influence the bio-efficacy of insecticides. Here, data are presented that confirm the variation in residual efficacy observed when monitoring household surfaces sprayed during PMI/USAID-supported IRS campaigns. All insecticides except alpha-cypermethrin showed evidence of failing to meet the minimum range of residual efficacy proposed in WHO criteria at least once. However, this initial effort in characterizing program-wide insecticide bio-efficacy indicates that some insecticides, such as bendiocarb and pirimiphos-methyl, may be vulnerable to variations in the local environment. Additionally, the comparative analysis performed in this study provides evidence that mosquito mortality rates differ with

Effects of thermal treatment on mineralogy and heavy metal behavior in iron oxide stabilized air pollution control residues

DEFF Research Database (Denmark)

Sørensen, Mette Abildgaard; Bender-Koch, C.; Starckpoole, M. M.

2000-01-01

Stabilization of air pollution control residues by coprecipitation with ferrous iron and subsequent thermal treatment (at 600 and 900 °C) has been examined as a means to reduce heavy metal leaching and to improve product stability. Changes in mineralogy and metal binding were analyzed using various...... analytical and environmental techniques. Ferrihydrite was formed initially but transformed upon thermal treatment to more stable and crystalline iron oxides (maghemite and hematite). For some metals leaching studies showed more substantial binding after thermal treatment, while other metals either....... Thermal treatment of the stabilized residues produced structures with an inherently better iron oxide stability. However, the concentration of metals in the leachate generally increased as a consequence of the decreased solubility of metals in the more stable iron oxide structure....

Treatment of waste incinerator air-pollution-control residues with FeSO4: Laboratory investigation of design parameters

DEFF Research Database (Denmark)

Jensen, Dorthe Lærke; Christensen, Thomas Højlund; Lundtorp, Kasper

2002-01-01

supplied, the liquid-to-solid ratio of the process, the separation of solids and wastewater, the sequence of material mixing, the possibilities of reuse of water, the feasibility of using secondary (brackish) water, and simple means to improve the wastewater quality. The investigation showed...... that an optimum process configuration could be obtained yielding a stabilised solid product with low leaching of heavy metals and a dischargable wastewater with high contents of salts (in order to remove salts from the solid product) and low concentrations of heavy metals. The amount of iron added to the APC......The key design parameters of a new process for treatment of air-pollution-control (APC) residues (the Ferroxprocess) were investigated in the laboratory. The optimisation involved two different APC-residues from actual incinerator plants. The design parameters considered were: amount of iron oxide...

Residual stresses due to weld repairs, cladding and electron beam welds and effect of residual stresses on fracture behavior. Annual report, September 1, 1977--November 30, 1978

International Nuclear Information System (INIS)

Rybicki, E.F.

1978-11-01

The study is divided into three tasks. Task I is concerned with predicting and understanding the effects of residual stresses due to weld repairs of pressure vessels. Task II examines residual stresses due to an electron beam weld. Task III addresses the problem of residual stresses produced by weld cladding at a nozzle vessel intersection. The objective of Task I is to develop a computational model for predicting residual stress states due to a weld repair of pressure vessel and thereby gain an understanding of the mechanisms involved in the creation of the residual stresses. Experimental data from the Heavy Section Steel Technology (HSST) program at Oak Ridge National Laboratories (ORNL) is used to validate the computational model. In Task II, the residual stress model is applied to the case of an electron beam weld of a compact tension freacture specimen. The results in the form of residual stresses near the weld are then used to explain unexpected fracture behavior which is observed in the testing of the specimen. For Task III, the residual stress model is applied to the cladding process used in nozzle regions of nuclear pressure vessels. The residual stresses obtained from this analysis are evaluated to determine their effect on the phenomena of under-clad cracking

Efeito residual de herbicidas aplicados em pré-emergência em diferentes solos Residual effect of herbicides applied in pre-emergence in different soils

Directory of Open Access Journals (Sweden)

M.H. Inoue

2011-06-01

Full Text Available O objetivo deste trabalho foi monitorar o efeito residual dos herbicidas ametryne, clomazone e diuron, aplicados em pré-emergência, utilizando amostras de um Neossolo Quartzarênico e de um Latossolo Vermelho, com texturas e composições contrastantes. Para isso, foram conduzidos seis bioensaios em casa de vegetação, com amostras de um Neossolo Quartzarênico (textura arenosa e de um Latossolo Vermelho (textura argilosa. Foi avaliado o efeito residual de ametryne (0, 1,60 e 2,40 kg ha-1, clomazone (0, 0,90 e 1,10 kg ha-1 e diuron (0, 1,60 e 3,20 kg ha-1, por meio de semeadura de bioindicador previamente selecionado (Cucumis sativus ou Brachiaria decumbens aos 0, 25, 50, 75 e 100 dias após a aplicação (DAA. Verificou-se que ametryne proporcionou 80% de controle até os 40 DAA, independentemente do solo e da dose. O clomazone apresentou efeito residual satisfatório quando aplicado na dose recomendada em solo argiloso, mantendo o controle acima de 80% até os 71 DAA. Em solo arenoso, o controle não foi satisfatório já aos 25 DAA, mesmo na dose recomendada para solo argiloso. Diuron apresentou alta estabilidade em solo argiloso, observando-se controle superior a 91% até os 100 DAA na dose recomendada e controle acima de 80% até os 54 DAA na dose recomendada para solo arenoso. No entanto, em solo arenoso não houve aumento do efeito residual, mesmo com a aplicação da dose recomendada para solo argiloso.The objective of this work was to monitor the residual effect of the herbicides ametryne, clomazone and diuron, applied in pre-emergence, using Psament and Red Latosol with contrasting texture and composition. Thus, six experiments were conducted under greenhouse conditions with samples of Psament (sandy texture and Red Latosol (clay texture. The residual effect of ametryne (0, 1.60 and 2.40 kg ha-1, clomazone (0, 0.90 and 1.10 kg ha-1 and diuron (0, 1.60 and 3.20 kg ha 1 was evaluated by sowing the test plant (Cucumis sativus or

Harvesting and handling agricultural residues for energy

Energy Technology Data Exchange (ETDEWEB)

Jenkins, B.M.; Summer, H.R.

1986-05-01

Significant progress in understanding the needs for design of agricultural residue collection and handling systems has been made but additional research is required. Recommendations are made for research to (a) integrate residue collection and handling systems into general agricultural practices through the development of multi-use equipment and total harvest systems; (b) improve methods for routine evaluation of agricultural residue resources, possibly through remote sensing and image processing; (c) analyze biomass properties to obtain detailed data relevant to engineering design and analysis; (d) evaluate long-term environmental, social, and agronomic impacts of residue collection; (e) develop improved equipment with higher capacities to reduce residue collection and handling costs, with emphasis on optimal design of complete systems including collection, transportation, processing, storage, and utilization; and (f) produce standard forms of biomass fuels or products to enhance material handling and expand biomass markets through improved reliability and automatic control of biomass conversion and other utilization systems. 118 references.

Effect of routine preoperative fasting on residual gastric volume and ...

African Journals Online (AJOL)

2016-02-10

Feb 10, 2016 ... Key words: Fasting, myomectomy, pH, residual gastric volume. Date of Acceptance: ... gastric volume and acid in patients undergoing myomectomy. Niger J Clin ..... of gastric residual volume: A simulated, controlled study.

Disposal of residues according paragraph 97 StrlSchV - Efficient self control and handling of applications for release from regulatory control; Entsorgung von Rueckstaenden nach paragraph 97 StrlSchV - effektive Selbstueberwachung und Bearbeitung von Entlassungsverfahren

Energy Technology Data Exchange (ETDEWEB)

Gellermann, R. [HGN Hydrogeologie GmbH, Braunschweig (Germany)

2005-07-01

To control residues according to paragraph 97 of the German Radiation Protection Ordinance (StrlSchV), the ordinance earmarks a self - control of involved companies in the case of very low specific activities, an authorisation of release from regulatory control to disposal in the case of higher specific activities and a balancing of disposed activities in the case of large amounts. The realisation of this regulation requires the exchange of information between owners of residues, disposing companies and authorities. In order to make this information available and controllable in an efficient way, a well structured system of documents was developed analogue to an existing system in waste management. Practical experiences with this system are discussed. (orig.)

Leaching from municipal solid waste incineration residues

Energy Technology Data Exchange (ETDEWEB)

Hyks, J.

2008-02-15

Leaching of pollutants from Municipal Solid Waste Incineration (MSWI) residues has been investigated combining a range of laboratory leaching experiments with geochemical modeling. Special attention was paid to assessing the applicability of laboratory data for subsequent modeling with respect to presumed full-scale conditions; both sample pretreatment and actual influence of leaching conditions on the results of laboratory experiments were considered. It was shown that sample pretreatment may have large impact on leaching test data. In particular, a significant fraction of Pb was shown mobile during the washing of residues with water. In addition, drying of residues (i.e. slow oxidation) prior to leaching experiments increased the leaching of Cr significantly. Significant differences regarding the leaching behavior of individual elements with respect to (non)equilibrium conditions in column percolation experiments were observed in the study. As a result, three groups of elements were identified based on the predominant leaching control and the influence of (non)equilibrium on the results of the laboratory column experiments: I. Predominantly availability-controlled elements (e.g. Na, K, Cl) II. Solubility-controlled elements (e.g. Ca, S, Si, Al, Ba, and Zn) III. Complexation-controlled elements (e.g. Cu and Ni) With respect to the above groups it was suggested that results of laboratory column experiments can, with consideration, be used to estimate full-scale leaching of elements from Group I and II. However, in order to avoid large underestimations in the assessment of leaching from Group III, it is imperative to describe the time-dependent transport of dissolved organic carbon (DOC) in the tested system or to minimize the physical non-equilibrium during laboratory experiments (e.g. bigger column, slower flow velocity). Forward geochemical modeling was applied to simulate long-term release of elements from a MSWI air-pollution-control residue. Leaching of a

[Development of residual voltage testing equipment].

Science.gov (United States)

Zeng, Xiaohui; Wu, Mingjun; Cao, Li; He, Jinyi; Deng, Zhensheng

2014-07-01

For the existing measurement methods of residual voltage which can't turn the power off at peak voltage exactly and simultaneously display waveforms, a new residual voltage detection method is put forward in this paper. First, the zero point of the power supply is detected with zero cross detection circuit and is inputted to a single-chip microcomputer in the form of pulse signal. Secend, when the zero point delays to the peak voltage, the single-chip microcomputer sends control signal to power off the relay. At last, the waveform of the residual voltage is displayed on a principal computer or oscilloscope. The experimental results show that the device designed in this paper can turn the power off at peak voltage and is able to accurately display the voltage waveform immediately after power off and the standard deviation of the residual voltage is less than 0.2 V at exactly one second and later.

Residual Stress Analysis for Engineering Applications by Means of Neutron Diffraction

International Nuclear Information System (INIS)

Gndupel-Herold, Thomas; Brand, Paul C.; Prask, Henry J.

1999-01-01

The economic and scientific importance of neutron diffraction residual stress analysis has led to an increasing number of suitable instruments worldwide. Recently, a dedicated state-of-the-art diffractometer has been installed at the National Institute of Standards and Technology reactor. It has been used for a variety of measurements on basic and engineering stress problems. Among the most prominent examples that have been investigated are residual stresses in rails, weldments, and plasma-sprayed coatings

Treatment of air pollution control residues with iron rich waste sulfuric acid: does it work for antimony (Sb)?

Science.gov (United States)

Okkenhaug, Gudny; Breedveld, Gijs D; Kirkeng, Terje; Lægreid, Marit; Mæhlum, Trond; Mulder, Jan

2013-03-15

Antimony (Sb) in air pollution control (APC) residues from municipal solid waste incineration has gained increased focus due to strict Sb leaching limits set by the EU landfill directive. Here we study the chemical speciation and solubility of Sb at the APC treatment facility NOAH Langøya (Norway), where iron (Fe)-rich sulfuric acid (∼3.6M, 2.3% Fe(II)), a waste product from the industrial extraction of ilmenite, is used for neutralization. Antimony in water extracts of untreated APC residues occurred exclusively as pentavalent antimonate, even at low pH and Eh values. The Sb solubility increased substantially at pH<10, possibly due to the dissolution of ettringite (at alkaline pH) or calcium (Ca)-antimonate. Treated APC residues, stored anoxically in the laboratory, simulating the conditions at the NOAH Langøya landfill, gave rise to decreasing concentrations of Sb in porewater, occurring exclusively as Sb(V). Concentrations of Sb decreased from 87-918μgL(-1) (day 3) to 18-69μgL(-1) (day 600). We hypothesize that an initial sorption of Sb to Fe(II)-Fe(III) hydroxides (green rust) and eventually precipitation of Ca- and Fe-antimonates (tripuhyite; FeSbO4) occurred. We conclude that Fe-rich, sulfuric acid waste is efficient to immobilize Sb in APC residues from waste incineration. Copyright © 2013 Elsevier B.V. All rights reserved.

Residual stress analysis for engineering applications by means of neutron diffraction

International Nuclear Information System (INIS)

Gnaeupel-Herold, T.; Brand, P.C.; Prask, H.J.

1999-01-01

Residual stresses originate from spatial differences in plastic deformation, temperature, or phase distribution, introduced by manufacturing processes or during service. Engineering parts and materials experience mechanical, thermal, and chemical loads during their service, and most of these loads introduce stresses that are superimposed on the already existing residual stresses. Residual stresses can therefore limit or improve life and strength of engineering parts; knowledge and understanding of these stresses is therefore critical for optimizing strength and durability. The economic and scientific importance of neutron diffraction residual stress analysis has led to an increasing number of suitable instruments worldwide. All of the major sources due in the next several years will have instruments for the sole purpose of performing residual stress and texture measurements. Recently, a dedicated, state-of-the-art diffractometer has been installed at the National Institute of Standards and Technology reactor. It has been used for a variety of measurements on basic and engineering stress problems. Among the most prominent examples that have been investigated in collaboration with industrial and academic partners are residual stresses in rails, weldments, and plasma-sprayed coatings

Influence of post-harvest treatments with fludioxonil and soy lecithin co-application in controlling blue and grey mould and fludioxonil residues in Coscia pears.

Science.gov (United States)

Schirra, M; D'Aquino, S; Migheli, Q; Pirisi, F M; Angioni, A

2009-01-01

The residue levels of fludioxonil (FLU) were determined in Coscia pear following a 1-, 2- or 4-min dip in an aqueous mixture of FLU containing 300 or 100 mg l(-1) (active ingredient, a.i.) at 20 and 50 degrees C, respectively, with or without 2% soy lecithin. The efficacy of heat treatment with water and FLU mixtures was investigated on artificially inoculated pears for the control of post-harvest decay caused by blue (Penicillium expansum Link) and grey (Botrytis cinerea Pers. ex Fr.) mould. Treatment with 300 mg l(-1) FLU at 20 degrees C increased residues significantly when treatment time rose from 1 to 2 min; no further increase was recorded when dip time raised from 2 to 4 min. FLU residue rates were unaffected by treatment time when 300 mg l(-1) a.i. was applied in combination with lecithin at 20 degrees C. While treatment with 100 mg l(-1) a.i. at 50 degrees C for 1 and 2 min resulted in similar residue levels, significantly higher residues were detected when dip time increased from 1 to 4 min. Co-application of lecithin significantly decreased FLU residues with respect to fruit treated with FLU alone. Treatments with FLU at 20 or 50 degrees C effectively controlled decay over 10 days of incubation. While co-application of lecithin did not affect the efficacy of FLU at 300 mg l(-1)and 20 degrees C, treatment efficacy decreased when lecithin was applied in combination with 100 mg l(-1) FLU and 50 degrees C for 4 min and to a greater extent when dip time was 1-2 min.

Drug and chemical residues in domestic animals.

Science.gov (United States)

Mussman, H C

1975-02-01

Given the large number of chemical substances that may find their way into the food supply, a system is needed to monitor their presence. The U. S. Department of Agriculture's Meat and Poultry Inspection Program routinely tests for chemical residues in animals coming to slaughter. Pesticides, heavy metals, growth promotants (hormones and hormonelike agents), and antibiotics are included. Samples are taken statistically so that inferences as to national incidence of residues can be drawn. When a problem is identified, a more selective sampling is designed to help follow up on the initial regulatory action. In testing for pesticides, only DDT and dieldrin are found with any frequency and their levels are decreasing; violative residues of any chlorinated hydrocarbon are generally a result of an industrial accident rather than agricultural usage. Analyses for heavy metals have revealed detectable levels of mercury, lead, and others, but none at levels that are considered a health hazard. Of the hormone or hormonelike substances, only diethylstilbestrol has been a residue problem and its future is uncertain. The most extensive monitoring for veterinary drugs is on the antimicrobials, including sulfonamides, streptomycin, and the tetracycline group of antibiotics that constitute the bulk of the violations; their simultaneous use prophylactically and therapeutically has contributed to the problem in certain cases. A strong, well-designed user education program on proper application of pesticides, chemicals, and veterinary drugs appears to be one method of reducing the incidence of unwanted residues.

Allelopathic Effect of Wheat and Barley Residues on Yield and Yield Components of Cowpea (Vigna sinensis L. and Weeds Control

Directory of Open Access Journals (Sweden)

M Shahbyki

2018-02-01

Full Text Available Introduction Weeds are a major constraint limiting crop yield in agricultural systems and in organic systems in particular. Although herbicides are efficient for weed control, continuous use has caused the development of resistance in weeds against several herbicides. Furthermore, herbicides also pollute the soil, water and aerial environments and herbicide residues in food have deteriorated food quality and enhanced the risk of diseases. Allelopathy is defined as the direct or indirect harmful or beneficial effects of one plant on another through the release of chemical compounds into the environment. Wheat (Triticum aestivum L. is known to be allelopathic against crops and weeds. The objective of this study was to investigate the allelopathic effect of wheat and barley residues on weeds control and cowpea yield. Materials and Methods An experiment was conducted as randomized complete block design with three replications at the research field (36° 25’E, 54° 58’N, 1349 m a.s.l. of Agricultural Faculty, Shahrood University of Technology in 2015. Treatments were included; weeding all season, no weeding, trifluralin according to the recommended dose (2 ton ha-1, foliar application of wheat straw extract (concentration of 50%, foliar application of wheat straw extract (concentration of 100%, the application of wheat residue mixed with the soil at a rate of 2 ton ha-1, the application of wheat residue mixed with the soil at a rate of 4 ton ha-1, the application of wheat residue mixed with the soil at a rate of 8 ton ha-1, foliar application of barley straw extract (concentration of 50%, foliar application of barley straw extract (concentration of 100%. Statistical analysis of data was performed with MSTAT-C software and means were compared with LSD test at the 5% level of probability. Results and Discussion The results showed that the effect of treatments was significant (P 0.01 on weed density and dry weight. Soil incorporation with wheat

Removal of residual particulate matter from filter media

Science.gov (United States)

Almlie, Jay C; Miller, Stanley J

2014-11-11

A method for removing residual filter cakes that remain adhered to a filter after typical particulate removal methodologies have been employed, such as pulse-jet filter element cleaning, for all cleanable filters used for air pollution control, dust control, or powder control.

Removal of residual particulate matter from filter media

Energy Technology Data Exchange (ETDEWEB)

Almlie, Jay C.; Miller, Stanley J.

2018-01-09

A method for removing residual filter cakes that remain adhered to a filter after typical particulate removal methodologies have been employed, such as pulse-jet filter element cleaning, for all cleanable filters used for air pollution control, dust control, or powder control.

Recovering recyclable materials from shredder residue

Science.gov (United States)

Jody, Bassam J.; Daniels, Edward J.; Bonsignore, Patrick V.; Brockmeier, Norman F.

1994-02-01

Each year, about 11 million tons of metals are recovered in the United States from about 10 million discarded automobiles. The recovered metals account for about 75 percent of the total weight of the discarded vehicles. The balance of the material, known as shredder residue, amounts to about three million tons annually and is currently landfilled. The residue contains a diversity of potentially recyclable materials, including polyurethane foams, iron oxides, and certain thermoplastics. This article discusses a process under development at Argonne National Laboratory to separate and recover the recyclable materials from this waste stream. The process consists essentially of two stages. First, a physical separation is used to recover the foams and the metal oxides, followed by a chemical process to extract certain thermoplastics. The status of the technology and the process economics are reviewed here.

Residual stresses

International Nuclear Information System (INIS)

Sahotra, I.M.

2006-01-01

The principal effect of unloading a material strained into the plastic range is to create a permanent set (plastic deformation), which if restricted somehow, gives rise to a system of self-balancing within the same member or reaction balanced by other members of the structure., known as residual stresses. These stresses stay there as locked-in stresses, in the body or a part of it in the absence of any external loading. Residual stresses are induced during hot-rolling and welding differential cooling, cold-forming and extruding: cold straightening and spot heating, fabrication and forced fitting of components constraining the structure to a particular geometry. The areas which cool more quickly develop residual compressive stresses, while the slower cooling areas develop residual tensile stresses, and a self-balancing or reaction balanced system of residual stresses is formed. The phenomenon of residual stresses is the most challenging in its application in surface modification techniques determining endurance mechanism against fracture and fatigue failures. This paper discusses the mechanism of residual stresses, that how the residual stresses are fanned and what their behavior is under the action of external forces. Such as in the case of a circular bar under limit torque, rectangular beam under limt moment, reclaiming of shafts welds and peening etc. (author)

Electrodialytic remediation of municipal solid waste incineration residues using different membranes

DEFF Research Database (Denmark)

Parés Viader, Raimon; Jensen, Pernille Erland; Ottosen, Lisbeth M.

2017-01-01

In the present work, three different commercial membrane brands were used in an identical electrodialytic cell setup and operating conditions, in order to reduce the leaching of metals and salt anions of two types of municipal solid waste incineration residues: air pollution control residues...... as a technology to upgrade municipal solid waste incineration residues....

National Transportation Safety Board : weak internal control impaired financial accountability

Science.gov (United States)

2001-09-28

The U. S. General Accounting Office (GAO) was asked to review the National Transportation Safety Board's (NTSB) internal controls over selected types of fiscal year expenditures. They were asked to determine whether internal control weaknesses were a...

Eggshell thinning and residues in mallards on year after DDE exposure

Science.gov (United States)

Haegele, M.A.; Hudson, R.H.

1974-01-01

A group of 16 mallard hens (Anas platyrhynchos), that had been given feed containing 40 ppm ofp,p'-DDE for 96 days, laid eggs with shells averaging about 15%?20% thinner than those of ten control birds during and up to 42 days after treatment. In eight of the treated birds killed at that time, whole-body DDE residues averaged 33.1 ppm (wet weight). The other eight treated birds and ten controls were kept through the winter with no additional DDE exposure and penned separately five days for individual egg collection about three weeks after laying began in spring. At that time (nearly 11 months after DDE feeding had stopped), the treated birds laid eggs with shells averaging 7.4% thinner than control eggshells (significant at P<0.05) and their whole-body DDE residues averaged 9.6 ppm (wet weight). Variations in eggshell thickness and DDE residues were considerable among treated birds. However, regression analysis showed moderate negative correlations (r=?0.51 to ?0.62) between eggshell thickness and DDE residues in whole bodies and eggs, and strong positive correlations (r=0.73 and 0.91) between DDE residues in whole bodies and in eggs.

Residual Stresses and Other Properties of Teardrops

Energy Technology Data Exchange (ETDEWEB)

Stroud, Mary Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Veirs, Douglas Kirk [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Berg, John M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hill, Mary Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rios, Daniel [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Duque, Juan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-07-26

The Department of Energy’s 3013 Standard for packaging plutonium-bearing materials for storage up to fifty years specifies a minimum of two individually welded, nested containers herein referred to as the 3013 outer and the 3013 inner.1 Stress corrosion cracking (SCC) is a potential failure mechanism for 3013 inner containers.2,3 The bagless transfer container (BTC), a 3013 inner container used by Hanford and Savanna River Site (SRS) made from 304L stainless steel (SS), poses the greatest concern for SCC.4,5 The Surveillance and Monitoring Program (SMP) use stressed metal samples known as teardrops as screening tools in SCC studies to evaluate factors that could result in cracks in the 3013 containers.6,7 This report provides background information on the teardrops used in the Los Alamos National Laboratory (LANL) SMP studies including method of construction, composition and variability. In addition, the report discusses measurements of residual stresses in teardrops and compares the results with residual stresses in BTCs reported previously.4 Factors affecting residual stresses, including teardrop dimensions and surface finish, are also discussed.

Thermal treatment of stabilized air pollution control residues in a waste incinerator pilot plant. Part 2: Leaching characteristics of bottom ashes.

Science.gov (United States)

Baun, Dorthe L; Christensen, Thomas H; Bergfeldt, Brita; Vehlow, Jürgen; Mogensen, Erhardt P B

2004-02-01

With the perspective of generating only one solid residue from waste incineration, co-feeding of municipal solid waste and air pollution control residues stabilized by the Ferrox process was investigated in the TAMARA pilot plant incinerator as described in Bergfeldt et al. (Waste Management Research, 22, 49-57, 2004). This paper reports on leaching from the combined bottom ashes. Batch leaching test, pH-static leaching tests, availability tests and column leaching tests were used to characterize the leaching properties. The leaching properties are key information in the context of reuse in construction or in landfilling of the combined residue. In general, the combined bottom ashes had leaching characteristics similar to the reference bottom ash, which contained no APC residue. However, As and Pb showed slightly elevated leaching from the combined bottom ashes, while Cr showed less leaching. The investigated combined bottom ashes had contents of metals comparable to what is expected at steady state after continuous co-feeding of APC residues. Only Cd and Pb were partly volatilized (30-40%) during the incineration process and thus the combined bottom ashes had lower contents of Cd and Pb than expected at steady state. Furthermore, a major loss of Hg was, not surprisingly, seen and co-feeding of Ferrox-products together with municipal solid waste will require dedicated removal of Hg in the flue gas to prevent a build up of Hg in the system. In spite of this, a combined single solid residue from waste incineration seems to be a significant environmental improvement to current technology.

Fact Sheet for Friction Materials Manufacturing Facilities Residual Risk and Technology Review

Science.gov (United States)

proposed amendments to the National Emission Standards for Hazardous Air Pollutants (NESHAP) for Friction Materials Manufacturing Facilities to address the results of the residual risk and technology review

Disposal of Rocky Flats residues as waste

International Nuclear Information System (INIS)

Dustin, D.F.; Sendelweck, V.S.

1993-01-01

Work is underway at the Rocky Flats Plant to evaluate alternatives for the removal of a large inventory of plutonium-contaminated residues from the plant. One alternative under consideration is to package the residues as transuranic wastes for ultimate shipment to the Waste Isolation Pilot Plant. Current waste acceptance criteria and transportation regulations require that approximately 1000 cubic yards of residues be repackaged to produce over 20,000 cubic yards of WIPP certified waste. The major regulatory drivers leading to this increase in waste volume are the fissile gram equivalent, surface radiation dose rate, and thermal power limits. In the interest of waste minimization, analyses have been conducted to determine, for each residue type, the controlling criterion leading to the volume increase, the impact of relaxing that criterion on subsequent waste volume, and the means by which rules changes may be implemented. The results of this study have identified the most appropriate changes to be proposed in regulatory requirements in order to minimize the costs of disposing of Rocky Flats residues as transuranic wastes

Transfer shuttle for vitrified residue canisters control of risks associated with external exposure and heat release

Energy Technology Data Exchange (ETDEWEB)

BIndel, L.; Gamess, A.; Lejeune, E.; Cellier, P.; Maillard, A. [SGN Reseau Eurisys, 78 - Saint Quentin (France)

1998-07-01

In the La Hague COGEMA's plant area, nuclear residue isolated by reprocessing are transported by means of specific transfer shuttles between the different processing and/or conditioning facilities and the storage ones. These shuttles are designed by reference to the applicable dose equivalent rate (DER) limits for transport on the site and the thermal behavior limitations of certain mechanical components which guarantee the containment of the transported waste. This paper describes and example of a study conducted on a transfer shuttle for vitrified residue canisters. Concerning the control of risks associated with external exposure and with heat releases, these were handled by the 'Shielding-Criticality-Dispersion' and 'process Modelling and Simulation' Sections of the Technical Division of SGN. The dose profiles around the shuttle, as a function of the shielding heterogeneities and possible radiation leakage, as well as the thermal fields within the shuttle, were calculated using 3D models. These design studies ultimately helped to select and validate the optimal solutions. (authors)

Field Test Kit for Gun Residue Detection; TOPICAL

International Nuclear Information System (INIS)

WALKER, PAMELA K.; RODACY, PHILIP J.

2002-01-01

One of the major needs of the law enforcement field is a product that quickly, accurately, and inexpensively identifies whether a person has recently fired a gun--even if the suspect has attempted to wash the traces of gunpowder off. The Field Test Kit for Gunshot Residue Identification based on Sandia National Laboratories technology works with a wide variety of handguns and other weaponry using gunpowder. There are several organic chemicals in small arms propellants such as nitrocellulose, nitroglycerine, dinitrotoluene, and nitrites left behind after the firing of a gun that result from the incomplete combustion of the gunpowder. Sandia has developed a colorimetric shooter identification kit for in situ detection of gunshot residue (GSR) from a suspect. The test kit is the first of its kind and is small, inexpensive, and easily transported by individual law enforcement personnel requiring minimal training for effective use. It will provide immediate information identifying gunshot residue

Residual number processing in dyscalculia.

Science.gov (United States)

Cappelletti, Marinella; Price, Cathy J

2014-01-01

Developmental dyscalculia - a congenital learning disability in understanding numerical concepts - is typically associated with parietal lobe abnormality. However, people with dyscalculia often retain some residual numerical abilities, reported in studies that otherwise focused on abnormalities in the dyscalculic brain. Here we took a different perspective by focusing on brain regions that support residual number processing in dyscalculia. All participants accurately performed semantic and categorical colour-decision tasks with numerical and non-numerical stimuli, with adults with dyscalculia performing slower than controls in the number semantic tasks only. Structural imaging showed less grey-matter volume in the right parietal cortex in people with dyscalculia relative to controls. Functional MRI showed that accurate number semantic judgements were maintained by parietal and inferior frontal activations that were common to adults with dyscalculia and controls, with higher activation for participants with dyscalculia than controls in the right superior frontal cortex and the left inferior frontal sulcus. Enhanced activation in these frontal areas was driven by people with dyscalculia who made faster rather than slower numerical decisions; however, activation could not be accounted for by response times per se, because it was greater for fast relative to slow dyscalculics but not greater for fast controls relative to slow dyscalculics. In conclusion, our results reveal two frontal brain regions that support efficient number processing in dyscalculia.

Residual number processing in dyscalculia

Directory of Open Access Journals (Sweden)

Marinella Cappelletti

2014-01-01

Full Text Available Developmental dyscalculia – a congenital learning disability in understanding numerical concepts – is typically associated with parietal lobe abnormality. However, people with dyscalculia often retain some residual numerical abilities, reported in studies that otherwise focused on abnormalities in the dyscalculic brain. Here we took a different perspective by focusing on brain regions that support residual number processing in dyscalculia. All participants accurately performed semantic and categorical colour-decision tasks with numerical and non-numerical stimuli, with adults with dyscalculia performing slower than controls in the number semantic tasks only. Structural imaging showed less grey-matter volume in the right parietal cortex in people with dyscalculia relative to controls. Functional MRI showed that accurate number semantic judgements were maintained by parietal and inferior frontal activations that were common to adults with dyscalculia and controls, with higher activation for participants with dyscalculia than controls in the right superior frontal cortex and the left inferior frontal sulcus. Enhanced activation in these frontal areas was driven by people with dyscalculia who made faster rather than slower numerical decisions; however, activation could not be accounted for by response times per se, because it was greater for fast relative to slow dyscalculics but not greater for fast controls relative to slow dyscalculics. In conclusion, our results reveal two frontal brain regions that support efficient number processing in dyscalculia.

Residual number processing in dyscalculia☆

Science.gov (United States)

Cappelletti, Marinella; Price, Cathy J.

2013-01-01

Developmental dyscalculia – a congenital learning disability in understanding numerical concepts – is typically associated with parietal lobe abnormality. However, people with dyscalculia often retain some residual numerical abilities, reported in studies that otherwise focused on abnormalities in the dyscalculic brain. Here we took a different perspective by focusing on brain regions that support residual number processing in dyscalculia. All participants accurately performed semantic and categorical colour-decision tasks with numerical and non-numerical stimuli, with adults with dyscalculia performing slower than controls in the number semantic tasks only. Structural imaging showed less grey-matter volume in the right parietal cortex in people with dyscalculia relative to controls. Functional MRI showed that accurate number semantic judgements were maintained by parietal and inferior frontal activations that were common to adults with dyscalculia and controls, with higher activation for participants with dyscalculia than controls in the right superior frontal cortex and the left inferior frontal sulcus. Enhanced activation in these frontal areas was driven by people with dyscalculia who made faster rather than slower numerical decisions; however, activation could not be accounted for by response times per se, because it was greater for fast relative to slow dyscalculics but not greater for fast controls relative to slow dyscalculics. In conclusion, our results reveal two frontal brain regions that support efficient number processing in dyscalculia. PMID:24266008

Residual stresses

International Nuclear Information System (INIS)

Macherauch, E.

1978-01-01

Residual stresses are stresses which exist in a material without the influence of external powers and moments. They come into existence when the volume of a material constantly changes its form as a consequence of mechanical, thermal, and/or chemical processes and is hindered by neighbouring volumes. Bodies with residual stress are in mechanical balance. These residual stresses can be manifested by means of all mechanical interventions disturbing this balance. Acoustical, optical, radiological, and magnetical methods involving material changes caused by residual stress can also serve for determining residual stress. Residual stresses have an ambivalent character. In technical practice, they are feared and liked at the same time. They cause trouble because they can be the cause for unexpected behaviour of construction elements. They are feared since they can cause failure, in the worst case with catastrophical consequences. They are appreciated, on the other hand, because, in many cases, they can contribute to improvements of the material behaviour under certain circumstances. But they are especially liked for their giving convenient and (this is most important) mostly uncontrollable explanations. For only in very few cases we have enough knowledge and possibilities for the objective evaluation of residual stresses. (orig.) [de

United Nations International Drug Control Programme responds

Directory of Open Access Journals (Sweden)

Michael Platzer

2002-01-01

Full Text Available [First paragraph] We would like to reply to the article written by Axel Klein entitled, "Between the Death Penalty and Decriminalization: New Directions for Drug Control in the Commonwealth Caribbean" published in NWIG 75 (3&4 2001. We have noted a number of factual inaccuracies as well as hostile comments which portray the United Nations International Drug Control Programme in a negative light. This reply is not intended to be a critique of the article, which we find unbalanced and polemical, but rather an alert to the tendentious statements about UNDCP, which we feel should be corrected.

36 CFR 1256.70 - What controls access to national security-classified information?

Science.gov (United States)

2010-07-01

... national security-classified information? 1256.70 Section 1256.70 Parks, Forests, and Public Property... HISTORICAL MATERIALS Access to Materials Containing National Security-Classified Information § 1256.70 What controls access to national security-classified information? (a) The declassification of and public access...

Evaluation of residue-residue contact predictions in CASP9

KAUST Repository

Monastyrskyy, Bohdan

2011-01-01

This work presents the results of the assessment of the intramolecular residue-residue contact predictions submitted to CASP9. The methodology for the assessment does not differ from that used in previous CASPs, with two basic evaluation measures being the precision in recognizing contacts and the difference between the distribution of distances in the subset of predicted contact pairs versus all pairs of residues in the structure. The emphasis is placed on the prediction of long-range contacts (i.e., contacts between residues separated by at least 24 residues along sequence) in target proteins that cannot be easily modeled by homology. Although there is considerable activity in the field, the current analysis reports no discernable progress since CASP8.

Sedentary behavior and residual-specific mortality

OpenAIRE

Paul D. Loprinzi; Meghan K. Edwards; Eveleen Sng; Ovuokerie Addoh

2016-01-01

Background: The purpose of this study was to examine the association of accelerometer-assessed sedentary behavior and residual-specific mortality. Methods: Data from the 2003-2006 National Health and Nutrition Examination Survey (NHANES) were used (N = 5536), with follow-up through 2011. Sedentary behavior was objectively measured over 7 days via accelerometry. Results: When expressing sedentary behavior as a 60 min/day increase, the hazard ratio across the models ranged from 1.07-1.40 (P < 0...

Air pollution control residues from waste incineration: current UK situation and assessment of alternative technologies.

Science.gov (United States)

Rani, D Amutha; Boccaccini, A R; Deegan, D; Cheeseman, C R

2008-11-01

Current disposal options for APC residues in the UK and alternative treatment technologies developed world-wide have been reviewed. APC residues are currently landfilled in the UK where they undergo in situ solidification, although the future acceptability of this option is uncertain because the EU waste acceptance criteria (WAC) introduce strict limits on leaching that are difficult to achieve. Other APC residue treatment processes have been developed which are reported to reduce leaching to below relevant regulatory limits. The Ferrox process, the VKI process, the WES-PHix process, stabilisation/solidification using cementitious binders and a range of thermal treatment processes are reviewed. Thermal treatment technologies convert APC residues combined with other wastes into inert glass or glass-ceramics that encapsulate heavy metals. The waste management industry will inevitably use the cheapest available option for treating APC residues and strict interpretation and enforcement of waste legislation is required if new, potentially more sustainable technologies are to become commercially viable.

Air pollution control residues from waste incineration: Current UK situation and assessment of alternative technologies

International Nuclear Information System (INIS)

Amutha Rani, D.; Boccaccini, A.R.; Deegan, D.; Cheeseman, C.R.

2008-01-01

Current disposal options for APC residues in the UK and alternative treatment technologies developed world-wide have been reviewed. APC residues are currently landfilled in the UK where they undergo in situ solidification, although the future acceptability of this option is uncertain because the EU waste acceptance criteria (WAC) introduce strict limits on leaching that are difficult to achieve. Other APC residue treatment processes have been developed which are reported to reduce leaching to below relevant regulatory limits. The Ferrox process, the VKI process, the WES-PHix process, stabilisation/solidification using cementitious binders and a range of thermal treatment processes are reviewed. Thermal treatment technologies convert APC residues combined with other wastes into inert glass or glass-ceramics that encapsulate heavy metals. The waste management industry will inevitably use the cheapest available option for treating APC residues and strict interpretation and enforcement of waste legislation is required if new, potentially more sustainable technologies are to become commercially viable

Effects of Bio-char on Soil Microbes in Herbicide Residual Soils

Directory of Open Access Journals (Sweden)

WANG Gen-lin

2015-10-01

Full Text Available Effects of biological carbon (bio-char on soil microbial community were studied by pot experiments simulating long residual herbicide residues in soil environment, which clarifed the improvement of biochar and its structural properties on soil microenvironment. The results showed that fungi and actinomycetes had the same effect tendency within 0~0.72 mg·kg-1 in clomazone residue which increased the role of stimulation with crop growth process prolonged, especially in high residue treatment, but strong inhibitory effect on bacteria community was occured early which returned to normal until sugar beet growth to fiftieth day. Soil fungi community decreased with bio-char adding, but had no significant difference with the control. When clomazone residue in soil was below 0.24 mg·kg-1, soil actinomycetes community was higher than control without bio-char, bacteria increased first and then reduced after adding carbon as below 0.12 mg·kg-1. Biochar was ‘deep hole’ structure containing C, O, S and other elements. The results showed that a certain concentration clomazone residue in soil would stimulate soil fungi and actinomycetes to grow. After adding the biochar, the inhibition effect of high herbicides residual on bacterial would be alleviated.

Modern bioenergy from agricultural and forestry residues in Cameroon: Potential, challenges and the way forward

DEFF Research Database (Denmark)

Ackom, Emmanuel; Alemagi, Dieudonne; Ackom, Nana B.

2013-01-01

liters of ethanol annually to displace 18–48% of the national consumption of gasoline. Alternatively, the residues could provide 0.08–0.22 billion liters of biomass to Fischer Tropsch diesel annually to offset 17–45% of diesel fuel use. For the generation of bioelectricity, the residues could supply 0...

Developments in hydroconversion processes for residues

Energy Technology Data Exchange (ETDEWEB)

Douwes, C T [Shell Res. B.V.; Wijffels, J B; Van Klinken, J; Van Zijll Langhout, W C

1979-01-01

A review of recent developments in hydrotreating processes for demetallization, desulfurization, and conversion to distillate products of residues covers catalyst developments for suppression of coke formation, maximum metals tolerance, and conversion selectivity; the effects of hydrogen pressure and temperature on catalyst deactivation and conversion; basic operating characteristics of conventional fixed-bed trickle-flow reactors, and of onstream catalyst replacement reactors, including the expanded-bed and the moving-bed reactor; a comparison of catalyst bed activity level, dirt tolerance, reactor effectiveness, temperature control, and thermal stability of the expanded-bed and moving-bed reactors; residue upgrading in slurry-bed reactors of dispersed vanadium sulfide catalyst in the oil; design and control features for safety and reliability; and a cost comparison between the indirect hydrotreating route, in which the asphalt fraction is separated prior to hydrotreating, and the as yet incompletely developed direct route.

Identification and discrimination of herbicide residues using a conducting polymer electronic nose

Science.gov (United States)

Alphus Dan Wilson

2016-01-01

The identification of herbicide residues on crop foliage is necessary to make crop-management decisions for weed pest control and to monitor pesticide residue levels on food crops. Electronic-nose (e-nose) methods were tested as a cheaper, alternative means of discriminating between herbicide residue types (compared with conventional chromatography methods), by...

Ammonia volatilization from crop residues and frozen green manure crops

NARCIS (Netherlands)

Ruijter, de F.J.; Huijsmans, J.F.M.; Rutgers, B.

2010-01-01

Agricultural systems can lose substantial amounts of nitrogen (N). To protect the environment, the European Union (EU) has adopted several directives that set goals to limit N losses. National Emission Ceilings (NEC) are prescribed in the NEC directive for nitrogen oxides and ammonia. Crop residues

Croatian National System of Nuclear Materials Control

International Nuclear Information System (INIS)

Biscan, R.

1998-01-01

In the process of economic and technological development of Croatia by using or introducing nuclear power or in the case of international co-operation in the field of peaceful nuclear activities, including international exchange of nuclear material, Croatia should establish and implement National System of Nuclear Materials Control. Croatian National System of accounting for and control of all nuclear material will be subjected to safeguards under requirements of Agreement and Additional Protocol between the Republic of Croatia and the International Atomic Energy Agency (IAEA) for the Application of Safeguards in Connection with the Treaty on the Non-Proliferation of Nuclear Weapons (NPT). The decision by NPT parties at the 1995 NPT Review and Extension Conference to endorse the Fullscope IAEA Safeguards Standard (FSS) as a necessary precondition of nuclear supply means that states are obliged to ensure that the recipient country has a FSS agreement in place before any nuclear transfer can take place (Ref. 1). The FSS standard of nuclear supply is a central element of the Nuclear Suppliers Group (NSG) Guidelines which the NSG adopted in 1992 and should be applied to members and non-members of the NSG. The FSS standard of nuclear supply in general allows for NPT parties or countries which have undertaken the same obligations through other treaty arrangements, to receive favourable treatment in nuclear supply arrangements. However, the Iraqi experience demonstrate that trade in nuclear and dual-use items, if not properly monitored, can contribute to a nuclear weapons program in countries acting contrary to their non-proliferation obligation. Multilateral nuclear export control mechanisms, including the FSS supply standard, provide the basis for co-ordination and standardisation of export control measures. (author)

Residues from waste incineration. Final report. Rev. ed.

Energy Technology Data Exchange (ETDEWEB)

Astrup, T.; Juul Pedersen, A.; Hyks, J.; Frandsen, F.J.

2010-04-15

The overall objective of the project was to improve the understanding of the formation and characteristics of residues from waste incineration. This was done focusing on the importance of the waste input and the operational conditions of the furnace. Data and results obtained from the project have been discussed in this report according to the following three overall parts: i) mass flows and element distribution, ii) flue gas/particle partitioning and corrosion/deposition aspects, and iii) residue leaching. This has been done with the intent of structuring the discussion while tacitly acknowledging that these aspects are interrelated and cannot be separated. Overall, it was found that the waste input composition had significant impact of the characteristics of the generated residues. A similar correlation between operational conditions and residue characteristics could not be observed. Consequently, the project recommend that optimization of residue quality should focus on controlling the waste input composition. The project results showed that including specific waste materials (and thereby also excluding the same materials) may have significant effects on the residue composition, residue leaching, aerosol and deposit formation.It is specifically recommended to minimize Cl in the input waste. Based on the project results, it was found that a significant potential for optimization of waste incineration exist. (Author)

Swelling kinetics of several residues from Shenhua coal extraction

Energy Technology Data Exchange (ETDEWEB)

Cao, Mei-xia; Shui, Heng-fu; Wang, Zhi-cai [Anhui University of Technology, Maanshan (China). School of Chemistry and Chemical Engineering

2008-08-15

In order to understand the mechanism of swelling and the relation between swelling behavior and solvent extraction, the swelling kinetics of residues from Shenhua coal extracted by CS{sub 2}/NMP with different mixing ratios were studied in different solvents. The result shows that the swelling rates of extraction residues increase along with swelling temperature. The swelling rate in polar solvent NMP is much higher than that in non-polar solvent THN. Solvent extraction has a great effect on the swelling of extraction residues. The swelling activation energy of extraction residues increases and the swelling rate decreases with the increase of extraction yield. The swelling activation energies of extraction residues in NMP and THN are less than 10 kJ/mol, suggesting that the swelling process is controlled by solvent molecular diffusion in coal structure. 22 refs., 2 figs., 7 tabs.

Electrodialytic removal of heavy metals and chloride from municipal solid waste incineration fly ash and air pollution control residue in suspension - test of a new two compartment experimental cell

DEFF Research Database (Denmark)

Kirkelund, Gunvor Marie; Magro, Cátia; Guedes, Paula

2015-01-01

Municipal solid waste incineration (MSWI) residues such as fly ash and air pollution control (APC) residues are classified as hazardous waste and disposed of, although they contain potential resources. The most problematic elements in MSWI residues are leachable heavy metals and salts. For reuse...... of MSWI residues in for instance concrete, the aim of remediation should be reduction of the heavy metal leaching, while at the same time keeping the alkaline pH, so the residue can replace cement. In this study a MSWI residues were subjected to electrodialytic remediation under various experimental...... heavy metal leaching except when the pH was reduced to a level below 8 for the fly ash. On the other hand, Cr leaching increased by the electrodialytic treatment. Cl leaching from the MSWI residues was less dependent on experimental conditions and was reduced in all experiments compared to the initial...

Strengthening control over radioactive sources in authorized use and regaining control over orphan sources. National strategies

International Nuclear Information System (INIS)

2004-02-01

The objective of this report is to provide practical guidance to States on the development of a national strategy for improving control over radioactive sources, particularly dangerous sources (Categories 1-3). Part of this process involves the determination of the magnitude of the potential problem with orphan and vulnerable sources and indeed, whether or not a national strategy is needed. The ultimate objective is that States will use this report to develop and then implement a plan of action that will result in all significant sources being managed in a safe and secure manner. This report attempts to provide both the background knowledge and the methodology necessary for an individual or small team of responsible persons to develop a national strategy for improving control over all radioactive sources, but especially orphan and vulnerable sources. The background knowledge given in Chapter 3 is an update of the information on practices that was given in IAEA-TECDOC-804, which focused on spent radioactive sources. After some introductory material, this report provides both the factual information and the general steps needed to develop and implement a national strategy. Part I contains background information for those who are not already familiar with the subject including the need for national strategies, the generic causes of loss of control of sources, with specific examples and the common applications of radioactive sources. Part II details the actual process for the development and implementation of a national strategy, which includes assessing the problem by first gathering specific and national information, determining the nature and magnitude of the problem, developing the national strategy by evaluating, and prioritizing possible solutions, implementing the strategy subsequent to a high level decision; and evaluating the effectiveness of the plan and making changes as a result until the desired objective is achieved. Searches for sources will be part of

Regulatory and management approaches to NORM residues in Malaysia

International Nuclear Information System (INIS)

Omar, M.; Teng, I.L.

2006-01-01

Naturally Occurring Radioactive Material (NORM) processing industries in Malaysia include oil and gas production and mineral processing plants. These industries are controlled by the Atomic Energy Licensing Board of Malaysia (AELB) through the enforcement of the Atomic Energy Licensing Act 1984 (Act 304). Related regulations have been developed in order to ensure the safety of workers and members of the public. However, more regulations are necessary for the safe handling of NORM. NORM processing generates various types of NORM residues that require proper management. As for low-level NORM residues, landfill disposal can be exempted from regulatory control if the Radiological Impact Assessment (RIA) shows that the additional dose to the members of the public is below the limit set by the authority. This paper outlines the regulatory and management approaches to NORM residues in Malaysia. (author)

Numerical and Experimental Study on the Residual Stresses in the Nitrided Steel

Science.gov (United States)

Song, X.; Zhang, Zhi-Qian; Narayanaswamy, S.; Huang, Y. Z.; Zarinejad, M.

2016-09-01

In the present work, residual stresses distribution in the gas nitrided AISI 4140 sample has been studied using finite element (FE) simulation. The nitrogen concentration profile is obtained from the diffusion-controlled compound layer growth model, and nitrogen concentration controls the material volume change through phase transformation and lattice interstitials which results in residual stresses. Such model is validated through residual stress measurement technique—micro-ring-core method, which is applied to the nitriding process to obtain the residual stresses profiles in both the compound and diffusion layer. The numerical and experimental results are in good agreement with each other; they both indicate significant stress variation in the compound layer, which was not captured in previous research works due to the resolution limit of the traditional methods.

A Study on the cooperation policy in multilateral nuclear control regimes and the advancing of national export control system

International Nuclear Information System (INIS)

Lee, Byung Wook; Oh, K. B.; Yang, M. H.; Lee, H. M.; Lee, K. S.; Ko, H. S.; Ryu, J. S.; Kim, J. S.

2004-08-01

This study carried out the analysis of trends of the multilateral nuclear control in four aspects. First, this study analyzes the past trends of the international nuclear non-proliferation regime, which includes the NPT, the IAEA safeguards system, the international nuclear export control regime and the physical protection of nuclear materials. Second, this study establishes the multilateral cooperation strategies for the effective cooperation in the process of strengthening the nuclear control regimes. Third, this study reviews the major agenda of nuclear control regimes and establishes national positions on each agenda. Fourth, this study also analyzes outstanding issues in nuclear control regimes and derives some factors to reflect national nuclear control system

Power Management Controls, Ernest Orlando Lawrence Berkeley National Laboratory; Power Management Controls, Ernest Orlando Lawrence Berkeley National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Westerberg, Emil [Dalarna Univ., Borlaenge (Sweden). Graphic Art Technology

2002-12-01

This report describes the work that is being conducted on power management controls at Berkeley National Laboratory. We can see a significant increasing amount of electronic equipment in our work places and in our every day life. Today's modern society depends on a constant energy flow. The future's increasing need of energy will burden our economy as well as our environment. The project group at Berkeley National Laboratory is working with leading manufacturers of office equipment. The goal is to agree on how interfaces for power management should be presented on office equipment. User friendliness and a more consistent power management interface is the project focus. The project group's role is to analyze data that is relevant to power management, as well as to coordinate communication and discussions among the involved parties.

On researching erosion-corrosion wear in pipelines: the rate and residual lifetime estimation

International Nuclear Information System (INIS)

Baranenko, V.I.; Yanchenko, Yu.A.; Gulina, O.M.; Dokukin, D.A.

2010-01-01

To base the normative document on calculation of pipelines erosive-corrosive wear (ECW) rate and residual lifetime this research of ECW regularities for pearlitic steel NPP pipelines was performed. The estimates of control data treatment statistical procedures efficiency were presented. The influence of the scheme of piping control on the ECW rate and residual lifetime estimation results was demonstrated. The simplified scheme is valid only in case of complete information. It's usage under data uncertainties leads to essential residual lifetime overstating [ru

Renewable energy from agro-residues in China. Solid biofuels and biomass briquetting technology

Energy Technology Data Exchange (ETDEWEB)

Chen, Longjian; Han, Lujia [Center for Biomass Resource Utilization, College of Engineering, China Agricultural University (East Campus), 17 Qing-Hua-Dong-Lu, Hai-Dian District, Beijing 100083 (China); Xing, Li [Service Center for Trading Technology Service, Chinese Academy of Agricultural Mechanization Sciences, Beijing 100083 (China)

2009-12-15

China has the abundant agro-residue resources, producing more than 630 million tons of agro-residues in 2006, and amounting to about 20% of total energy consumption in rural areas. Efficient utilization of enormous agro-residues resource is crucial for providing bioenergy, releasing risk of environmental pollution, and increasing farmers' income. The paper presented the feasibility of densified solid biofuels technology for utilizing agro-residues in China. The output and distribution of agro-residues in recent 10 years, the R and D of briquetting technology, and the market of densified solid biofuels from agro-residues in China have been analyzed. The result indicated that the abundant agro-residue resources can provide the economical and sustainable raw material for densified solid biofuels development in China. The R and D of briquetting technology at present can strongly support the large scale production of densified solid biofuels. With continued improvement and cost reduction of briquetting technology, along with the support of nation energy policy on biomass energy, the market of densified solid biofuels from agro-residues in China will be more fully deployed. Based on the above mentioned key factors, development of densified solid biofuels from agro-residues in China will be promising and feasible. (author)

Renewable energy from agro-residues in China. Solid biofuels and biomass briquetting technology

International Nuclear Information System (INIS)

Chen, Longjian; Han, Lujia; Xing, Li

2009-01-01

China has the abundant agro-residue resources, producing more than 630 million tons of agro-residues in 2006, and amounting to about 20% of total energy consumption in rural areas. Efficient utilization of enormous agro-residues resource is crucial for providing bioenergy, releasing risk of environmental pollution, and increasing farmers' income. The paper presented the feasibility of densified solid biofuels technology for utilizing agro-residues in China. The output and distribution of agro-residues in recent 10 years, the R and D of briquetting technology, and the market of densified solid biofuels from agro-residues in China have been analyzed. The result indicated that the abundant agro-residue resources can provide the economical and sustainable raw material for densified solid biofuels development in China. The R and D of briquetting technology at present can strongly support the large scale production of densified solid biofuels. With continued improvement and cost reduction of briquetting technology, along with the support of nation energy policy on biomass energy, the market of densified solid biofuels from agro-residues in China will be more fully deployed. Based on the above mentioned key factors, development of densified solid biofuels from agro-residues in China will be promising and feasible. (author)

Annatto seed residue (Bixa orellana L.: nutritional quality

Directory of Open Access Journals (Sweden)

Melissa Alessandra Valério

2015-06-01

Full Text Available Considering that annatto seeds are rich in protein, the present work aimed to evaluate the biological quality of this nutrient in the meal residue originating from annatto seed processing. We determined the general composition, mineral levels, amino acid composition and chemical scores, antinutritional factors, and protein quality using biological assays. The following values were obtained: 11.50% protein, 6.74% moisture, 5.22% ash, 2.22% lipids, 42.19% total carbohydrates and 28.45% fiber. The residue proved to be a food rich in fiber and also a protein source. Antinutritional factors were not detected. The most abundant amino acids were lysine, phenylalanine + tyrosine, leucine and isoleucine. Valine was the most limiting amino acid (chemical score 0.22. The protein quality of the seed residue and the isolated protein showed no significant differences. The biological value was lower than that of the control protein but higher than that found in other vegetables. Among the biochemical analyses, only creatinine level was decreased in the two test groups compared to the control group. Enzyme tests did not indicate liver toxicity. The results showed favorable aspects for the use of annatto seed residue in the human diet, meriting further research.

Pesticide residues in food of plant origin from Southeast Asia – A Nordic project

DEFF Research Database (Denmark)

Skretteberg, L. G.; Lyrån, B.; Holen, B.

2015-01-01

Fruits and vegetables from Souteast Asia were analysed for the presence of pesticide residues. A total of 721 samples of 63 different commodities were collected in 2011. The products were imported to Denmark, Finland, Norway and Sweden from ten countries; about 80% were imported from Thailand....... The reason for the increased control for certain food products from Southeast Asia was that the official control had revealed many products with too high levels of pesticide residues. In 60% of the samples we did not find any residues, while 28% had residues below or at the MRLs. Results above the MRLs were...

pH and Organic Carbon Dose Rates Control Microbially Driven Bioremediation Efficacy in Alkaline Bauxite Residue.

Science.gov (United States)

Santini, Talitha C; Malcolm, Laura I; Tyson, Gene W; Warren, Lesley A

2016-10-18

Bioremediation of alkaline tailings, based on fermentative microbial metabolisms, is a novel strategy for achieving rapid pH neutralization and thus improving environmental outcomes associated with mining and refining activities. Laboratory-scale bioreactors containing bauxite residue (an alkaline, saline tailings material generated as a byproduct of alumina refining), to which a diverse microbial inoculum was added, were used in this study to identify key factors (pH, salinity, organic carbon supply) controlling the rates and extent of microbially driven pH neutralization (bioremediation) in alkaline tailings. Initial tailings pH and organic carbon dose rates both significantly affected bioremediation extent and efficiency with lower minimum pHs and higher extents of pH neutralization occurring under low initial pH or high organic carbon conditions. Rates of pH neutralization (up to 0.13 mM H + produced per day with pH decreasing from 9.5 to ≤6.5 in three days) were significantly higher in low initial pH treatments. Representatives of the Bacillaceae and Enterobacteriaceae, which contain many known facultative anaerobes and fermenters, were identified as key contributors to 2,3-butanediol and/or mixed acid fermentation as the major mechanism(s) of pH neutralization. Initial pH and salinity significantly influenced microbial community successional trajectories, and microbial community structure was significantly related to markers of fermentation activity. This study provides the first experimental demonstration of bioremediation in bauxite residue, identifying pH and organic carbon dose rates as key controls on bioremediation efficacy, and will enable future development of bioreactor technologies at full field scale.

Costs and CO{sub 2} benefits of recovering, refining and transporting logging residues for fossil fuel replacement

Energy Technology Data Exchange (ETDEWEB)

Gustavsson, Leif [Ecotechnology, Department of Engineering and Sustainable Development, Mid Sweden University, 83125 Oestersund (Sweden); Linnaeus University, 35195 Vaexjoe (Sweden); Eriksson, Lisa; Sathre, Roger [Ecotechnology, Department of Engineering and Sustainable Development, Mid Sweden University, 83125 Oestersund (Sweden)

2011-01-15

There are many possible systems for recovering, refining, and transporting logging residues for use as fuel. Here we analyse costs, primary energy and CO{sub 2} benefits of various systems for using logging residues locally, nationally or internationally. The recovery systems we consider are a bundle system and a traditional chip system in a Nordic context. We also consider various transport modes and distances, refining the residues into pellets, and replacing different fossil fuels. Compressing of bundles entails costs, but the cost of chipping is greatly reduced if chipping is done on a large scale, providing an overall cost-effective system. The bundle system entails greater primary energy use, but its lower dry-matter losses mean that more biomass per hectare can be extracted from the harvest site. Thus, the potential replacement of fossil fuels per hectare of harvest area is greater with the bundle system than with the chip system. The fuel-cycle reduction of CO{sub 2} emissions per harvest area when logging residues replace fossil fuels depends more on the type of fossil fuel replaced, the logging residues recovery system used and the refining of the residues, than on whether the residues are transported to local, national or international end-users. The mode and distance of the transport system has a minor impact on the CO{sub 2} emission balance. (author)

Residual Resistance Data from Cavity Production Projects at Jefferson Lab

International Nuclear Information System (INIS)

Ciovati, Gianluigi; Geng, Rongli; Mammosser, John; Saunders, Jeffrey

2010-01-01

A fundamental limitation towards achieving high quality factors in superconducting radio-frequency cavities is the so-called residual resistance. Understanding and controlling the residual resistance has important implications towards improving the efficiency and reduce the operating cost of continuous wave superconducting linear accelerators. In this contribution we will report on the residual resistance values obtained from measurements of the quality factor of a large set of cavities, with resonant frequency between 805 MHz and 1.5 GHz, all of them processed and tested at Jefferson Lab. Surface treatments included both buffered chemical polishing and electropolishing. The results indicate an approximate value of the residual resistance of about 7-10 n Omega.

Understanding tobacco control policy at the national level: bridging the gap between public policy and tobacco control advocacy

Directory of Open Access Journals (Sweden)

Marc C. Willemsen

2018-03-01

Full Text Available Background While some countries have advanced tobacco control policies, other countries struggle to adopt and implement FCTC's measures. This presentation uncovers the main factors that explain such variations, taking insights from public policy and political science as a starting point for a case study. Methods A case study of tobacco control policy making in the Netherlands, covering the period from the 1960s until the present. The study consisted of a systematic search and analysis of documents and proceedings of parliamentary debates on tobacco policy, supplemented with 22 interviews with key informants from the government, health organisations, politicians, and the tobacco industry. In addition, documents from the Truth Tobacco Industry Documents database, pertaining to the influence of the tobacco industry on Dutch policy making, were analysed. Results The Dutch government started relatively late to regulate tobacco. The choices in tobacco control policy making at the national level and the tempo in which they are made are explained by the interaction of the five main elements of the tobacco control policy making process: Relatively stable context factors (constitutional structures, 'rules of the policy making game', national cultural values Relatively dynamic context factors (regime changes, EU regulation and FCTC guidelines, changing social norms, public support Transfer of ideas (availability and interpretation of scientific evidence Pro and anti-tobacco control networks and coalitions (their organisational and lobby strength Agenda-setting (changes in problem definition, issue framing, media advocacy Conclusions Despite worldwide convergence of tobacco control policies, accelerated by the ratification of the FCTC treaty by most nations, governments develop approaches to tobacco control in line with cultural values, ideological preferences and specific national institutional arrangements. There is no one-size-fits-all approach. The

Metallic elements fractionation in municipal solid waste incineration residues

Science.gov (United States)

Kowalski, Piotr R.; Kasina, Monika; Michalik, Marek

2016-04-01

Municipal solid waste incineration (MSWI) residues are represented by three main materials: bottom ash, fly ash and air pollution control (APC) residues. Among them ˜80 wt% is bottom ash. All of that materials are products of high temperature (>1000° C) treatment of waste. Incineration process allows to obtain significant reduction of waste mass (up to 70%) and volume (up to 90%) what is commonly used in waste management to reduce the amount need to be landfilled or managed in other way. Incineration promote accumulation non-combustible fraction of waste, which part are metallic elements. That type of concentration is object of concerns about the incineration residues impact on the environment and also gives the possibility of attempts to recover them. Metallic elements are not equally distributed among the materials. Several factors influence the process: melting points, volatility and place and forms of metallic occurrence in the incinerated waste. To investigate metallic elements distribution in MSWI residues samples from one of the biggest MSW incineration plant in Poland were collected in 2015. Chemical analysis with emphasis on the metallic elements content were performed using inductively coupled plasma optical emission (ICP-OES) and mass spectrometry (ICP-MS). The bottom ash was a SiO2-CaO-Al2O3-Fe2O3-Na2O rich material, whereas fly ash and APC residues were mostly composed of CaO and SiO2. All of the materials were rich in amorphous phase occurring together with various, mostly silicate crystalline phases. In a mass of bottom ash 11 wt% were metallic elements but also in ashes 8.5 wt% (fly ash) and ˜4.5 wt% (APC residues) of them were present. Among the metallic elements equal distribution between bottom and fly ash was observed for Al (˜3.85 wt%), Mn (770 ppm) and Ni (˜65 ppm). In bottom ash Fe (5.5 wt%), Cr (590 ppm) and Cu (1250 ppm) were concentrated. These values in comparison to fly ash were 5-fold higher for Fe, 3-fold for Cu and 1.5-fold for

Active control of residual tool marks for freeform optics functionalization by novel biaxial servo assisted fly cutting.

Science.gov (United States)

Zhu, Zhiwei; To, Suet; Zhang, Shaojian

2015-09-01

The inherent residual tool marks (RTM) with particular patterns highly affect optical functions of the generated freeform optics in fast tool servo or slow tool servo (FTS/STS) diamond turning. In the present study, a novel biaxial servo assisted fly cutting (BSFC) method is developed for flexible control of the RTM to be a functional micro/nanotexture in freeform optics generation, which is generally hard to achieve in FTS/STS diamond turning. In the BSFC system, biaxial servo motions along the z-axis and side-feeding directions are mainly adopted for primary surface generation and RTM control, respectively. Active control of the RTM from the two aspects, namely, undesired effect elimination or effective functionalization, are experimentally demonstrated by fabricating a typical F-theta freeform surface with scattering homogenization and two functional microstructures with imposition of secondary phase gratings integrating both reflective and diffractive functions.

Conformation of dehydropentapeptides containing four achiral amino acid residues – controlling the role of L-valine

Directory of Open Access Journals (Sweden)

Michał Jewgiński

2014-03-01

Full Text Available Structural studies of pentapeptides containing an achiral block, built from two dehydroamino acid residues (ΔZPhe and ΔAla and two glycines, as well as one chiral L-Val residue were performed using NMR spectroscopy. The key role of the L-Val residue in the generation of the secondary structure of peptides is discussed. The obtained results suggest that the strongest influence on the conformation of peptides arises from a valine residue inserted at the C-terminal position. The most ordered conformation was found for peptide Boc-Gly-ΔAla-Gly-ΔZPhe-Val-OMe (3, which adopts a right-handed helical conformation.

Geodetic Control Information on Passive Marks: Horizontal and Vertical Geodetic Control Data for the United States - National Geospatial Data Asset (NGDA) Geodetic Control Information on Passive Marks

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This data contains a set of geodetic control stations maintained by the National Geodetic Survey. Each geodetic control station in this dataset has either a precise...

Pesticide residues in orange fruit from citrus orchards in Nuevo Leon State, Mexico.

Science.gov (United States)

Suárez-Jacobo, Angela; Alcantar-Rosales, Victor Manuel; Alonso-Segura, Diana; Heras-Ramírez, Maria; Elizarragaz-De La Rosa, Dalau; Lugo-Melchor, Ofelia; Gaspar-Ramirez, Octavio

2017-09-01

Some international organisations established maximum residue limits (MRLs) in food to protect human health. Mexico lacks regulations in this matter, affecting national and international trade from agroindustry. The aim of this study was to diagnose pesticide residues in oranges from Nuevo Leon, México, in citrus orchards. In May 2014, 100 orange fruit samples were taken randomly from orchards and subjected to analysis for 93 pesticides at residual level by GC/QQQ-MS and LCQ-TOF-MS. Results showed the presence of 15 pesticide residues in the samples. The comparison of the residual levels of pesticides found in orange samples among the MRLs allowed by USA, EU and Japanese regulations demonstrated that all samples were below MRLs issued by USA and Japan. Some orange samples were above MRLs issued by the EU. This provides a basis to establish strategies in order to satisfy International Standards to protect human health and encourage Food Safety in Mexico.

Study on indium leaching from mechanically activated hard zinc residue

Directory of Open Access Journals (Sweden)

Yao J.H.

2011-01-01

Full Text Available In this study, changes in physicochemical properties and leachability of indium from mechanically activated hard zinc residue by planetary mill were investigated. The results showed that mechanical activation increased specific surface area, reaction activity of hard zinc residue, and decreased its particle size, which had a positive effect on indium extraction from hard zinc residue in hydrochloric acid solution. Kinetics of indium leaching from unmilled and activated hard zinc residue were also investigated, respectively. It was found that temperature had an obvious effect on indium leaching rate. Two different kinetic models corresponding to reactions which are diffusion controlled, [1-(1- x1/3]2=kt and (1-2x/3-(1-x2/3=kt were used to describe the kinetics of indium leaching from unmilled sample and activated sample, respectively. Their activation energies were determined to be 17.89 kJ/mol (umilled and 11.65 kJ/mol (activated within the temperature range of 30°C to 90°C, which is characteristic for a diffusion controlled process. The values of activation energy demonstrated that the leaching reaction of indium became less sensitive to temperature after hard zinc residue mechanically activated by planetary mill.

Construction of a risk assessment system for chemical residues in agricultural products.

Science.gov (United States)

Choi, Shinai; Hong, Jiyeon; Lee, Dayeon; Paik, Minkyoung

2014-01-01

Continuous monitoring of chemical residues in agricultural and food products has been performed by various government bodies in South Korea. These bodies have made attempts to systematically manage this information by creating a monitoring database system as well as a system based on these data with which to assess the health risk of chemical residues in agricultural products. Meanwhile, a database system is being constructed consisting of information about monitoring and, following this, a demand for convenience has led to the need for an evaluation tool to be constructed with the data processing system. Also, in order to create a systematic and effective tool for the risk assessment of chemical residues in foods and agricultural products, various evaluation models are being developed, both domestically and abroad. Overseas, systems such as Dietary Exposure Evaluation Model: Food Commodity Intake Database and Cumulative and Aggregate Risk Evaluation System are being used; these use the US Environmental Protection Agency as a focus, while the EU has developed Pesticide Residue Intake Model for assessments of pesticide exposure through food intake. Following this, the National Academy of Agricultural Science (NAAS) created the Agricultural Products Risk Assessment System (APRAS) which supports the use and storage of monitoring information and risk assessments. APRAS efficiently manages the monitoring data produced by NAAS and creates an extraction feature included in the database system. Also, the database system in APRAS consists of a monitoring database system held by the NAAS and food consumption database system. Food consumption data is based on Korea National Health and Nutrition Examination Survey. This system is aimed at exposure and risk assessments for chemical residues in agricultural products with regards to different exposure scenarios.

Proceedings of a specialist meeting on regulatory approaches for the control of environmental residues containing naturally occurring radioactive material. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-07-01

Naturally occurring radionuclides are present in most material. The most common naturally occurring radionuclides in material are those of the uranium and thorium series and potassium-40. This material is commonly referred to as Naturally Occurring Radioactive Material (NORM). In some material the levels of naturally occurring radionuclides are significantly higher, to the extent that regulatory control may be required for radiation protection purposes. Regulation of NORM presents a range of new challenges for both regulators and operators. Unlike more traditional industries dealing with radionuclides, NORM industries have generally not had any radiological oversight and, for example, are not equipped for radiological monitoring. Some consumer goods containing NORM, which have not traditionally been considered as a radiological problem (such as some fertilizers), may require regulation and this may have social and economic consequences. The transport and disposal of NORM are also a concern, particularly due to the large volumes, which may need to be considered. For the majority of NORM, disposal has been by conventional means in the same way as for non-hazardous waste with no specific attention to radiological aspects. In some cases, there may be a need for intervention into existing NORM disposal sites. The International Commission on Radiological Protection (ICRP) published ICRP No. 82, Protection of the Public in Situations of Prolonged Radiation Exposure in 2000. This document provides guidance on managing residues, such as those arising from NORM industries, with potential impact on the public. However, with NORM residual waste there may be three different situations: residual waste created as the result of a past practice, residual waste created by an ongoing practice and waste which will arise from future activities. Regulation of NORM may therefore be consistent with consideration of a practice, an intervention or a combination of both. Different regulatory

Proceedings of a specialist meeting on regulatory approaches for the control of environmental residues containing naturally occurring radioactive material. Working material

International Nuclear Information System (INIS)

2005-01-01

Naturally occurring radionuclides are present in most material. The most common naturally occurring radionuclides in material are those of the uranium and thorium series and potassium-40. This material is commonly referred to as Naturally Occurring Radioactive Material (NORM). In some material the levels of naturally occurring radionuclides are significantly higher, to the extent that regulatory control may be required for radiation protection purposes. Regulation of NORM presents a range of new challenges for both regulators and operators. Unlike more traditional industries dealing with radionuclides, NORM industries have generally not had any radiological oversight and, for example, are not equipped for radiological monitoring. Some consumer goods containing NORM, which have not traditionally been considered as a radiological problem (such as some fertilizers), may require regulation and this may have social and economic consequences. The transport and disposal of NORM are also a concern, particularly due to the large volumes, which may need to be considered. For the majority of NORM, disposal has been by conventional means in the same way as for non-hazardous waste with no specific attention to radiological aspects. In some cases, there may be a need for intervention into existing NORM disposal sites. The International Commission on Radiological Protection (ICRP) published ICRP No. 82, Protection of the Public in Situations of Prolonged Radiation Exposure in 2000. This document provides guidance on managing residues, such as those arising from NORM industries, with potential impact on the public. However, with NORM residual waste there may be three different situations: residual waste created as the result of a past practice, residual waste created by an ongoing practice and waste which will arise from future activities. Regulation of NORM may therefore be consistent with consideration of a practice, an intervention or a combination of both. Different regulatory

Forest treatment residues for thermal energy compared with disposal by onsite burning: Emissions and energy return

Science.gov (United States)

Greg Jones; Dan Loeffler; David Calkin; Woodam Chung

2010-01-01

Mill residues from forest industries are the source for most of the current wood-based energy in the US, approximately 2.1% of the nation's energy use in 2007. Forest residues from silvicultural treatments, which include limbs, tops, and small non-commercial trees removed for various forest management objectives, represent an additional source of woody biomass for...

Performance of a biogas upgrading process based on alkali absorption with regeneration using air pollution control residues.

Science.gov (United States)

Baciocchi, Renato; Carnevale, Ennio; Costa, Giulia; Gavasci, Renato; Lombardi, Lidia; Olivieri, Tommaso; Zanchi, Laura; Zingaretti, Daniela

2013-12-01

This work analyzes the performance of an innovative biogas upgrading method, Alkali absorption with Regeneration (AwR) that employs industrial residues and allows to permanently store the separated CO2. This process consists in a first stage in which CO2 is removed from the biogas by means of chemical absorption with KOH or NaOH solutions followed by a second stage in which the spent absorption solution is contacted with waste incineration Air Pollution Control (APC) residues. The latter reaction leads to the regeneration of the alkali reagent in the solution and to the precipitation of calcium carbonate and hence allows to reuse the regenerated solution in the absorption process and to permanently store the separated CO2 in solid form. In addition, the final solid product is characterized by an improved environmental behavior compared to the untreated residues. In this paper the results obtained by AwR tests carried out in purposely designed demonstrative units installed in a landfill site are presented and discussed with the aim of verifying the feasibility of this process at pilot-scale and of identifying the conditions that allow to achieve all of the goals targeted by the proposed treatment. Specifically, the CO2 removal efficiency achieved in the absorption stage, the yield of alkali regeneration and CO2 uptake resulting for the regeneration stage, as well as the leaching behavior of the solid product are analyzed as a function of the type and concentration of the alkali reagent employed for the absorption reaction. Copyright © 2013 Elsevier Ltd. All rights reserved.

National infection prevention and control programmes: Endorsing quality of care.

Science.gov (United States)

Stempliuk, Valeska; Ramon-Pardo, Pilar; Holder, Reynaldo

2014-01-01

Core components Health care-associated infections (HAIs) are a major cause of morbidity and mortality. In addition to pain and suffering, HAIs increase the cost of health care and generates indirect costs from loss of productivity for patients and society as a whole. Since 2005, the Pan American Health Organization has provided support to countries for the assessment of their capacities in infection prevention and control (IPC). More than 130 hospitals in 18 countries were found to have poor IPC programmes. However, in the midst of many competing health priorities, IPC programmes are not high on the agenda of ministries of health, and the sustainability of national programmes is not viewed as a key point in making health care systems more consistent and trustworthy. Comprehensive IPC programmes will enable countries to reduce the mobility, mortality and cost of HAIs and improve quality of care. This paper addresses the relevance of national infection prevention and control (NIPC) programmes in promoting, supporting and reinforcing IPC interventions at the level of hospitals. A strong commitment from national health authorities in support of national IPC programmes is crucial to obtaining a steady decrease of HAIs, lowering health costs due to HAIs and ensuring safer care.

Selecting RMF Controls for National Security Systems

Energy Technology Data Exchange (ETDEWEB)

Witzke, Edward L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-08-01

In 2014, the United States Department of Defense started tra nsitioning the way it performs risk management and accreditation of informatio n systems to a process entitled Risk Management Framework for DoD Information Technology or RMF for DoD IT. There are many more security and privacy contro ls (and control enhancements) from which to select in RMF, than there w ere in the previous Information Assurance process. This report is an attempt t o clarify the way security controls and enhancements are selected. After a brief overview and comparison of RMF for DoD I T with the previously used process, this report looks at the determination of systems as National Security Systems (NSS). Once deemed to be an NSS, this report addr esses the categorization of the information system with respect to impact level s of the various security objectives and the selection of an initial baseline o f controls. Next, the report describes tailoring the controls through the use of overl ays and scoping considerations. Finally, the report discusses organizatio n-defined values for tuning the security controls to the needs of the information system.

The National Implementation of Nuclear Export Controls: Developing a Best Practices Model

Energy Technology Data Exchange (ETDEWEB)

Viski, Andrea [European University Institute, Department of Law, Badia Fiesolana, S.Domenico di Fiesole, Firenze (Italy)

2011-12-15

The nuclear renaissance promises significant benefits to the international community, but also raises security challenges, particularly relating to the trade of nuclear materials and equipment. The objective of this paper is to examine how supply-side non-proliferation efforts can be strengthened by developing a best practices model for national nuclear export control implementation. In order to achieve this goal, nuclear export control measures identified by the 1540 Committee will be used as a framework from which a best practices model can be formed. Such a model concentrates specifically on national legislation and enforcement measures delineated by the Committee in order to bring countries in accordance with international law. Developing a best practices model seeks to deliver an ideal process for national export control law actualization in order to encourage the peaceful development of nuclear energy and develop the infrastructure and framework for precluding nuclear proliferation.

Embedding operational research into national disease control programme: lessons from 10 years of experience in Indonesia

Directory of Open Access Journals (Sweden)

Yodi Mahendradhata

2014-10-01

Full Text Available There is growing recognition that operational research (OR should be embedded into national disease control programmes. However, much of the current OR capacity building schemes are still predominantly driven by international agencies with limited integration into national disease control programmes. We demonstrated that it is possible to achieve a more sustainable capacity building effort across the country by establishing an OR group within the national tuberculosis (TB control programme in Indonesia. Key challenges identified include long-term financial support, limited number of scientific publications, and difficulties in documenting impact on programmatic performance. External evaluation has expressed concerns in regard to utilisation of OR in policy making. Efforts to address this concern have been introduced recently and led to indications of increased utilisation of research evidence in policy making by the national TB control programme. Embedding OR in national disease control programmes is key in establishing an evidence-based disease control programme.

Release of bound residues of atrazine from soils through autoclaving and gamma radiation sterilization

International Nuclear Information System (INIS)

Nakagawa, L.E.; Andréa, M.M.

1997-01-01

The sterilization methods are particularly important to study the influence of microorganisms on the pesticide dissipation in soils. This study, conducted in the laboratories of the Instituto Biológico of São Paulo in august 1996, tested the influence of two methods of soil sterilization - moist heat (autoclaving) and γ radiation - on the release of nonextractable or bound residues. It was studied, as example, bound residues of the herbicide atrazine in two types of soil (gley humic and dark red latosol). In the soil samples submitted to the moist heat sterilization, the recovery of the previously bound residues as reextractable residues was 5.6 and 5.9 times higher than in the control soils, not submitted to any sterilization process. Therefore, the method itself released the residues, indicating that the autoclaving is not the most appropriate method for studies on the influence of microorganisms on the release of bound residues. Otherwise, the γ radiation did not modify the residues recovery when compared to the controls. (author) [pt

Standardized Approach to Quantitatively Measure Residual Limb Skin Health in Individuals with Lower Limb Amputation.

Science.gov (United States)

Rink, Cameron L; Wernke, Matthew M; Powell, Heather M; Tornero, Mark; Gnyawali, Surya C; Schroeder, Ryan M; Kim, Jayne Y; Denune, Jeffrey A; Albury, Alexander W; Gordillo, Gayle M; Colvin, James M; Sen, Chandan K

2017-07-01

Objective: (1) Develop a standardized approach to quantitatively measure residual limb skin health. (2) Report reference residual limb skin health values in people with transtibial and transfemoral amputation. Approach: Residual limb health outcomes in individuals with transtibial ( n  = 5) and transfemoral ( n  = 5) amputation were compared to able-limb controls ( n  = 4) using noninvasive imaging (hyperspectral imaging and laser speckle flowmetry) and probe-based approaches (laser doppler flowmetry, transcutaneous oxygen, transepidermal water loss, surface electrical capacitance). Results: A standardized methodology that employs noninvasive imaging and probe-based approaches to measure residual limb skin health are described. Compared to able-limb controls, individuals with transtibial and transfemoral amputation have significantly lower transcutaneous oxygen tension, higher transepidermal water loss, and higher surface electrical capacitance in the residual limb. Innovation: Residual limb health as a critical component of prosthesis rehabilitation for individuals with lower limb amputation is understudied in part due to a lack of clinical measures. Here, we present a standardized approach to measure residual limb health in people with transtibial and transfemoral amputation. Conclusion: Technology advances in noninvasive imaging and probe-based measures are leveraged to develop a standardized approach to quantitatively measure residual limb health in individuals with lower limb loss. Compared to able-limb controls, resting residual limb physiology in people that have had transfemoral or transtibial amputation is characterized by lower transcutaneous oxygen tension and poorer skin barrier function.

Efeito residual de sulfentrazone, isoxaflutole e oxyfluorfen em três solos Residual effect of sulfentrazone, isoxaflutole and oxyfluorfen in three soils

Directory of Open Access Journals (Sweden)

C.A.D Melo

2010-12-01

Full Text Available As características físicas e químicas do solo, além das condições climáticas, influenciam o comportamento de herbicidas aplicados em pré-emergência das plantas daninhas. Dessa forma, objetivou-se avaliar o efeito residual de sulfentrazone, isoxaflutole e oxyfluorfen em três solos. O ensaio foi conduzido em ambiente protegido e o delineamento experimental foi em blocos casualizados, com quatro repetições. Os tratamentos, para cada solo, foram dispostos em esquema fatorial 3 x 5, sendo três herbicidas e cinco épocas de semeadura após aplicação dos produtos. Os herbicidas sulfentrazone, oxyfluorfen e isoxaflutole foram aplicados nas doses de 0,5, 0,72 e 0,113 kg ha-1, respectivamente, sobre potes plásticos de 250 mL previamente preenchidos com os dois solos de textura argilosa e um de textura franco-arenosa. Posteriormente, procedeu-se à semeadura da espécie bioindicadora Sorghum bicolor de forma escalonada, aos 0, 15, 30, 45 e 60 dias após a aplicação (DAA. Uma testemunha sem herbicida foi semeada nas diferentes épocas para cada solo e usada como comparação nas avaliações. Aos 21 dias após a semeadura em cada época, realizaram-se avaliações de intoxicação e crescimento das plantas através da massa seca da parte aérea. As plantas de sorgo, no solo argiloso com 9,0 dag kg-1 de matéria orgânica (MO submetido à aplicação de isoxaflutole, sulfentrazone e oxyfluorfen, produziram massa seca da parte aérea igual a 34, 20 e 40%, respectivamente, aos 60 DAA, em relação às plantas crescidas nesse solo sem aplicação do herbicida. No solo franco-arenoso, observou-se elevado efeito residual dos herbicidas sulfentrazone e oxyfluorfen e diminuição do efeito residual do isoxaflutole ao longo do tempo, com 80, 90 e 40% de controle aos 60 DAA, respectivamente. No solo argiloso com 4,4 dag kg-1 de MO, verificou-se que o herbicida isoxaflutole perdeu a eficácia de controle ao longo do tempo, diferentemente do

A survey of residual analysis and a new test of residual trend.

Science.gov (United States)

McDowell, J J; Calvin, Olivia L; Klapes, Bryan

2016-05-01

A survey of residual analysis in behavior-analytic research reveals that existing methods are problematic in one way or another. A new test for residual trends is proposed that avoids the problematic features of the existing methods. It entails fitting cubic polynomials to sets of residuals and comparing their effect sizes to those that would be expected if the sets of residuals were random. To this end, sampling distributions of effect sizes for fits of a cubic polynomial to random data were obtained by generating sets of random standardized residuals of various sizes, n. A cubic polynomial was then fitted to each set of residuals and its effect size was calculated. This yielded a sampling distribution of effect sizes for each n. To test for a residual trend in experimental data, the median effect size of cubic-polynomial fits to sets of experimental residuals can be compared to the median of the corresponding sampling distribution of effect sizes for random residuals using a sign test. An example from the literature, which entailed comparing mathematical and computational models of continuous choice, is used to illustrate the utility of the test. © 2016 Society for the Experimental Analysis of Behavior.

Identification of Key Residues in Virulent Canine Distemper Virus Hemagglutinin That Control CD150/SLAM-Binding Activity▿

Science.gov (United States)

Zipperle, Ljerka; Langedijk, Johannes P. M.; Örvell, Claes; Vandevelde, Marc; Zurbriggen, Andreas; Plattet, Philippe

2010-01-01

Morbillivirus cell entry is controlled by hemagglutinin (H), an envelope-anchored viral glycoprotein determining interaction with multiple host cell surface receptors. Subsequent to virus-receptor attachment, H is thought to transduce a signal triggering the viral fusion glycoprotein, which in turn drives virus-cell fusion activity. Cell entry through the universal morbillivirus receptor CD150/SLAM was reported to depend on two nearby microdomains located within the hemagglutinin. Here, we provide evidence that three key residues in the virulent canine distemper virus A75/17 H protein (Y525, D526, and R529), clustering at the rim of a large recessed groove created by β-propeller blades 4 and 5, control SLAM-binding activity without drastically modulating protein surface expression or SLAM-independent F triggering. PMID:20631152

Residual strength of repaired graphite/epoxy laminates after 5 years of outdoor exposure

Science.gov (United States)

Deaton, Jerry W.

1990-01-01

The NASA Langley Research Center has sponsored research to develop generic repair techniques and processes for advanced graphite/epoxy (Gr/Ep) composites applicable to secondary structures for commercial transport aircraft. The long-term durability of such repairs is being addressed in a 10-year outdoor exposure program at the Langley Research Center. Details of the program and results of residual strength tests after 5 years of outdoor exposure are presented. Four repair methods are being evaluated. These include: (1) externally bolted aluminum-plus adhesive; (2) precured, bonded external Gr/Ep; (3) cure-in-place external Gr/Ep; and (4) cure-in-place flush Gr/Ep. Repaired specimens as well as undamaged and damaged unrepaired controls are being exposed outdoors for 1, 3, 5, 7, and 10 years. The residual tensile strength of stressed, unstressed, and fatigue specimens from each group is reported and compared with the tensile strength of baseline specimens which received no outdoor exposure. Identification of the commercial products and companies is used to describe adequately the test materials. The identification of these commercial products does not constitute endorsement, expressed or implied, of such products by the National Aeronautics and Space Administration.

National pulpwood production, 2008

Science.gov (United States)

Tony G. Johnson; Ronald J. Piva; Brian F. Walters; al. et.

2011-01-01

United States’ pulpwood production amounted to 89.2 million cords in 2008. Roundwood production totaled 63.0 million cords and accounted for 71 percent of the Nation’s total pulpwood production. The use of wood residue totaled 26.2 million cords. Georgia led the Nation in total production, with 11.6 million cords. In 2008, 146 mills were operating and drawing wood from...

Monitoring of Benomyl Residue in Mushroom Marketed in Hamadan City

Directory of Open Access Journals (Sweden)

S. Abdi

2015-07-01

Full Text Available Introduction & Objective: Pesticide residues in environment and food have a negative impact on the health of living organisms. Therefore, this study was carried out for evaluation of benomyl residues in mushroom marketed in Hamadan city in 2014 using spectrophotometry. Materials & Methods: 10 specimens of mushroom were collected from greenhouses and market basket of Hamadan city. After preparation and processing the samples in the laboratory, be-nomyl residues in samples were determined using a spectrophotometric method in 3 replica-tions. All statistical analyses were performed using the SPSS statistical package. Results: The mean concentration of benomyl residues in samples were 5.90±0.75, 2.10± 0.487, 40.04±1.346, 0.32±0.044, 14.0±0.785, 1.54±0.304, 40.0±0.45, 0.87±0.055, 0.66± 0.032 and 49.60±0.303 µg kg-1 and more than the maximum residue limit (MRL provided by the World Health Organization (10 ppb. The results of the comparison of the mean concentration of pesticide residues among samples revealed significant differences in most of the samples (P<0.05. Conclusion: The results showed that mean concentrations of benomyl residues in mushroom samples were exceeding that of the MRL. Therefore, it is essential to impart proper education to the farming community about hazards involved in the overuse of toxic pesticides. Also, codification of laws and their enforcement and implementation of programs for the regular periodic monitoring of pesticide residues in foodstuffs especially in vegetables cultivated un-der greenhouse conditions at the national level to protect consumers’ health are recom-mended.(Sci J Hamadan Univ Med Sci 2015; 22 (2: 137-143

Persistence and bioaccumulation of oxyfluorfen residues in onion.

Science.gov (United States)

Sondhia, Shobha

2010-03-01

A field study was conducted to determine persistence and bioaccumulation of oxyflorfen residues in onion crop at two growth stages. Oxyfluorfen (23.5% EC) was sprayed at 250 and 500 g ai/ha on the crop (variety, N53). Mature onion and soil samples were collected at harvest. Green onion were collected at 55 days from each treated and control plot and analyzed for oxyfluorfen residues by a validated high-performance liquid chromatography method with an accepted recovery of 78-92% at the minimum detectable concentration of 0.003 microg g(-1). Analysis showed 0.015 and 0.005 microg g(-1) residues of oxyfluorfen at 250 g a.i. ha(-1) rate in green and mature onion samples, respectively; however, at 500 g a.i.ha(-1) rates, 0.025 and 0.011 microg g(-1) of oxyfluorfen residues were detected in green and mature onion samples, respectively. Soil samples collected at harvest showed 0.003 and 0.003 microg g(-1) of oxyfluorfen residues at the doses 250 and 500 g a.i. ha(-1), respectively. From the study, a pre-harvest interval of 118 days for onion crop after the herbicide application is suggested.

Effects of sugammadex on incidence of postoperative residual neuromuscular blockade: a randomized, controlled study.

Science.gov (United States)

Brueckmann, B; Sasaki, N; Grobara, P; Li, M K; Woo, T; de Bie, J; Maktabi, M; Lee, J; Kwo, J; Pino, R; Sabouri, A S; McGovern, F; Staehr-Rye, A K; Eikermann, M

2015-11-01

This study aimed to investigate whether reversal of rocuronium-induced neuromuscular blockade with sugammadex reduced the incidence of residual blockade and facilitated operating room discharge readiness. Adult patients undergoing abdominal surgery received rocuronium, followed by randomized allocation to sugammadex (2 or 4 mg kg(-1)) or usual care (neostigmine/glycopyrrolate, dosing per usual care practice) for reversal of neuromuscular blockade. Timing of reversal agent administration was based on the providers' clinical judgement. Primary endpoint was the presence of residual neuromuscular blockade at PACU admission, defined as a train-of-four (TOF) ratio sugammadex patients and 33 out of 76 (43.4%) usual care patients had TOF-Watch SX-assessed residual neuromuscular blockade at PACU admission (odds ratio 0.0, 95% CI [0-0.06], Psugammadex vs usual care (14.7 vs. 18.6 min respectively; P=0.02). After abdominal surgery, sugammadex reversal eliminated residual neuromuscular blockade in the PACU, and shortened the time from start of study medication administration to the time the patient was ready for discharge from the operating room. Clinicaltrials.gov:NCT01479764. © The Author 2015. Published by Oxford University Press on behalf of the British Journal of Anaesthesia. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Antibiotic Residues - A Global Health Hazard

Directory of Open Access Journals (Sweden)

Nisha A.R.

Full Text Available Use of Antibiotic that might result in deposition of residues in meat, milk and eggs must not be permitted in food intended for human consumption. If use of antibiotics is necessary as in prevention and treatment of animal diseases, a withholding period must be observed until the residues are negligible or no longer detected. The use of antibiotics to bring about improved performance in growth and feed efficiency, to synchronize or control of reproductive cycle and breeding performance also often lead to harmful residual effects. Concern over antibiotic residues in food of animal origin occurs in two times; one which produces potential threat to direct toxicity in human, second is whether the low levels of antibiotic exposure would result in alteration of microflora, cause disease and the possible development of resistant strains which cause failure of antibiotic therapy in clinical situations. A withdrawal period is established to safeguard human from exposure of antibiotic added food. The withdrawal time is the time required for the residue of toxicological concern to reach safe concentration as defined by tolerance. It is the interval from the time an animal is removed from medication until permitted time of slaughter. Heavy responsibility is placed on the veterinarian and livestock producer to observe the period for a withdrawal of a drug prior to slaughter to assure that illegal concentration of drug residue in meat, milk and egg do not occur. Use of food additives may improve feed efficiency 17% in beef cattle, 10% in lambs, 15% in poultry and 15% in swine. But their indiscriminate use will produce toxicity in consumers. WHO and FAO establish tolerances for a drug, pesticide or other chemical in the relevant tissues of food producing animals. The tolerance is the tissue concentration below, which a marker residue for the drug or chemical must fall in the target tissue before that animal edible tissues are considered safe for human

Influx of CO2 from Soil Incubated Organic Residues at Constant Temperature

Directory of Open Access Journals (Sweden)

Shoukat Ali Abro

2016-06-01

Full Text Available Temperature induced CO2 from genotypic residue substances is still less understood. Two types of organic residues (wheat- maize were incubated at a constant temperature (25°C to determine the rate and cumulative influx of CO2 in laboratory experiment for 40 days. Further, the effect of surface and incorporated crop residues with and without phosphorus addition was also studied. Results revealed that mixing of crop residues increased CO2-C evolution significantly & emission rare was 37% higher than that of control. At constant temperature, soil mixed residues, had higher emission rates CO2-C than the residues superimposed. There was linear correlation of CO2-C influxed for phosphorus levels and residue application ways with entire incubation at constant temperature. The mixing of organic residues to soil enhanced SOC levels and biomass of microbially bound N; however to little degree ammonium (NH4-N and nitrate NO3-N nitrogen were decreased.

Circulating microRNA levels predict residual beta cell function and glycaemic control in children with type 1 diabetes mellitus

DEFF Research Database (Denmark)

Samandari, Nasim; Mirza, Aashiq H; Nielsen, Lotte B

2017-01-01

AIMS/HYPOTHESIS: We aimed to identify circulating microRNA (miRNA) that predicts clinical progression in a cohort of 123 children with new-onset type 1 diabetes mellitus. METHODS: Plasma samples were prospectively obtained at 1, 3, 6, 12 and 60 months after diagnosis from a subset of 40 children......RNAs revealed significant enrichment for pathways related to gonadotropin-releasing hormone receptor and angiogenesis pathways. CONCLUSIONS/INTERPRETATION: The miRNA hsa-miR-197-3p at 3 months was the strongest predictor of residual beta cell function 1 year after diagnosis in children with type 1 diabetes...... from the Danish Remission Phase Cohort, and profiled for miRNAs. At the same time points, meal-stimulated C-peptide and HbA1c levels were measured and insulin-dose adjusted HbA1c (IDAA1c) calculated. miRNAs that at 3 months after diagnosis predicted residual beta cell function and glycaemic control...

Cavity pressure/residual stress measurements from the Non-Proliferation Experiment

Energy Technology Data Exchange (ETDEWEB)

Heinle, R.A.; Hudson, B.C. [Lawrence Livermore National Lab., CA (United States); Hatch, M.A. Jr.

1994-12-31

The Lawrence Livermore National Laboratory planned and conducted experiments on the Non-Proliferation Experiment to determine post-detonation gas pressure inside the explosive cavity and the residual rock stress in the region immediately outside the cavity. Before detonation there was significant concern that steam and detonation products would create very high temperatures and pressure in the blast cavity that would exist for weeks and months after firing. This could constitute a safety hazard to personnel re-entering the tunnel. Consequently the Lawrence Livermore National Laboratory was asked to field its Cavity Pressure/Residual stress monitor system on the Non-Proliferation Experiment. We obtained experimental data for the first 600 ms after the explosion and again several weeks after detonation upon tunnel re-entry. We recorded early-time cavity pressure of about 8.3 MPa. In addition we believe that the ends of our sensor hoses were subjected to an ambient driving pressure of about 0.5 MPa (absolute) that persisted until at least three weeks after zero time.

An extension of command shaping methods for controlling residual vibration using frequency sampling

Science.gov (United States)

Singer, Neil C.; Seering, Warren P.

1992-01-01

The authors present an extension to the impulse shaping technique for commanding machines to move with reduced residual vibration. The extension, called frequency sampling, is a method for generating constraints that are used to obtain shaping sequences which minimize residual vibration in systems such as robots whose resonant frequencies change during motion. The authors present a review of impulse shaping methods, a development of the proposed extension, and a comparison of results of tests conducted on a simple model of the space shuttle robot arm. Frequency shaping provides a method for minimizing the impulse sequence duration required to give the desired insensitivity.

Basic components of a national control system for nuclear materials

International Nuclear Information System (INIS)

Rabot, G.

1986-01-01

The paper presents the different aspects related to the organization and the functioning of a national control and accounting system for nuclear materials. The legal aspects and the relations with the IAEA are included

Control of pyrethroid and DDT-resistant Anopheles gambiae by application of indoor residual spraying or mosquito nets treated with a long-lasting organophosphate insecticide, chlorpyrifos-methyl

Directory of Open Access Journals (Sweden)

Chabi Joseph

2010-02-01

Full Text Available Abstract Background Scaling up of long-lasting insecticidal nets (LLINs and indoor residual spraying (IRS with support from the Global Fund and President's Malaria Initiative is providing increased opportunities for malaria control in Africa. The most cost-effective and longest-lasting residual insecticide DDT is also the most environmentally persistent. Alternative residual insecticides exist, but are too short-lived or too expensive to sustain. Dow Agrosciences have developed a microencapsulated formulation (CS of the organophosphate chlorpyrifos methyl as a cost-effective, long-lasting alternative to DDT. Methods Chlorpyrifos methyl CS was tested as an IRS or ITN treatment in experimental huts in an area of Benin where Anopheles gambiae and Culex quinquefasiactus are resistant to pyrethroids, but susceptible to organophosphates. Efficacy and residual activity was compared to that of DDT and the pyrethroid lambdacyalothrin. Results IRS with chlorpyrifos methyl killed 95% of An. gambiae that entered the hut as compared to 31% with lambdacyhalothrin and 50% with DDT. Control of Cx. quinquefasciatus showed a similar trend; although the level of mortality with chlorpyrifos methyl was lower (66% it was still much higher than for DDT (14% or pyrethroid (15% treatments. Nets impregnated with lambdacyhalothrin were compromized by resistance, killing only 30% of An. gambiae and 8% of Cx. quinquefasciatus. Nets impregnated with chlorpyrifos methyl killed more (45% of An gambiae and 15% of Cx. quinquefasciatus, but its activity on netting was of short duration. Contact bioassays on the sprayed cement-sand walls over the nine months of monitoring showed no loss of activity of chlorpyrifos methyl, whereas lambdacyhalothrin and DDT lost activity within a few months of spraying. Conclusion As an IRS treatment against pyrethroid resistant mosquitoes chlorpyrifos methyl CS outperformed DDT and lambdacyhalothrin. In IRS campaigns, chlorpyrifos methyl CS should

Effect of residual stress induced by cold expansion on fatigue crack ...

African Journals Online (AJOL)

Fatigue life and fatigue crack growth rate are controlled by stress ratio, stress level, orientation of crack, temper-ature, residual stress, corrosion, etc. The effects of residual stress on fatigue crack growth in aluminium (Al) alloy 2024-T351 by Mode I crack were investigated by applying constant amplitude cycles based on ...

Surveillance of veterinary drug residues in pork meat in Madagascar

Directory of Open Access Journals (Sweden)

M. V. Rakotoharinome

2015-06-01

Table I presents the results of the percentage of positive samples in the various regions of Madagascar. On average 37.2% sam­ples were contaminated by antimicrobial residues. A significant increase from 32 to 39% was observed between 2010 and 2011, respectively. No significant differences were found between samples according to sex, breed or age class in individual ani­mals. No differences between pig farm origins were found either (Figure 1. However, Amoron’i Mania Region, and particularly suburban Ambositra, was the most contaminated area in 2010 (67%; n = 9 and Melaky region (Western Madagascar in 2011. Pork meat samples originating from the same production area were less contaminated by drug residues when the animals were slaughtered in urban abattoirs compared to provincial abat­toirs. In this first step toward a national surveillance system, we confirm that drug residues in animal products are a serious public health concern for Madagascar.

Evaluation of Crops Sensitivity to Atrazine Soil Residual

Directory of Open Access Journals (Sweden)

E Izadi

2012-02-01

Full Text Available Abstract In order to study the sensitivity of 9 crops to atrazine soil residual, two separate experiments were conducted in field and greenhouse conditions. First experiment was conducted in a field with treated soil by atrazine based on split plot and the results evaluated in greenhouse conditions. Treatments in the field experiment included two organic manure application rates (0 and 50 t/ha as main plots and 2 atrazine application rates (2 and 4 kg/ha atrazine a.i. as sob plots. After corn harvesting soil was sampled at 0-15 cm surface layer in each plots in 15 points, after mixing the samples. Wheat, barley, sugar beet, pea, lens and colza planted in pots at greenhouse. Second experiment conducted in greenhouse conditions for evaluation of atrazine soil residual in completely randomized design. Treatments included atrazine soil residual concentrations (0, 0.2, 0.5, 1, 5, 10 and 15 mg/kg soil and crops included wheat, barley, sugar beet, pea, lens, rape, bean and tomato. Results showed that atrazine residue had no effect on crops growth in field experiment treated with atrazine. It seems that atrazine residue in filed soil is lower that its damage threshold for crops or maybe for its fast removal in field than in control conditions. But in bioassay experiment (greenhouse experiment crops response to atrazine residues were different. Results showed that onion and pea were most susceptible ant tolerant crops between studied species and based of ED50 parameter the other crops tolerance to total residue ranked as: pea< bean< lentil< sugar beet< tomato< barley< wheat< rape< onion. Keywords: Atrazine residue, Pea, Bean, Lentil, Sugar beet, Barley, Wheat, Rape, Tomato

Verification and Validation of Residual Stresses in Bi-Material Composite Rings

Energy Technology Data Exchange (ETDEWEB)

Nelson, Stacy Michelle [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Hanson, Alexander Anthony [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Briggs, Timothy [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Werner, Brian T. [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

2017-07-01

Process-induced residual stresses commonly occur in composite structures composed of dissimilar materials. These residual stresses form due to differences in the composite materials’ coefficients of thermal expansion and the shrinkage upon cure exhibited by polymer matrix materials. Depending upon the specific geometric details of the composite structure and the materials’ curing parameters, it is possible that these residual stresses could result in interlaminar delamination or fracture within the composite. Therefore, the consideration of potential residual stresses is important when designing composite parts and their manufacturing processes. However, the experimental determination of residual stresses in prototype parts can be time and cost prohibitive. As an alternative to physical measurement, it is possible for computational tools to be used to quantify potential residual stresses in composite prototype parts. Therefore, the objectives of the presented work are to demonstrate a simplistic method for simulating residual stresses in composite parts, as well as the potential value of sensitivity and uncertainty quantification techniques during analyses for which material property parameters are unknown. Specifically, a simplified residual stress modeling approach, which accounts for coefficient of thermal expansion mismatch and polymer shrinkage, is implemented within the Sandia National Laboratories’ developed SIERRA/SolidMechanics code. Concurrent with the model development, two simple, bi-material structures composed of a carbon fiber/epoxy composite and aluminum, a flat plate and a cylinder, are fabricated and the residual stresses are quantified through the measurement of deformation. Then, in the process of validating the developed modeling approach with the experimental residual stress data, manufacturing process simulations of the two simple structures are developed and undergo a formal verification and validation process, including a mesh

Disposal of residue from uranium ore processing in France

International Nuclear Information System (INIS)

Crochon, Ph.

2011-01-01

Between 1949 and 2001, French mines produced 76, 000 metric tons of uranium and 50 million metric tons of ore, processing residues are stored at 17 sites (in ponds enclosed by dykes or in former open-cast mines) subject to ICPE (classified facility for environment protection) regulation. These disposal sites cover surface areas of between one and several tens of hectares and several thousands to several millions of metric tons of waste are stored at them. When uranium mining stopped in France, these sites were redeveloped, with caps placed over the residue to provide mechanical and radiological protection. All these sites are still monitored by AREVA. In the last fifteen years, these sites have been the subject of a number of studies, especially regarding the long-term evolution and impact of the residue. These studies are now being pursued within the framework of the national plan for the management of nuclear materials and waste (PNGMDR). A regulatory and institutional framework regarding long-term management of these disposal sites needs to be defined. (author)

Effect of water-washing on the co-removal of chlorine and heavy metals in air pollution control residue from MSW incineration.

Science.gov (United States)

Yang, Zhenzhou; Tian, Sicong; Ji, Ru; Liu, Lili; Wang, Xidong; Zhang, Zuotai

2017-10-01

The present study systemically investigated the effect of a water-washing process on the removal of harmful chlorides, sulfates, and heavy metals in the air pollution control (APC) residue from municipal solid wastes incineration (MSWI), for sake of a better reuse and disposal of this kind of waste. In addition, the kinetic study was conducted to reveal the releasing mechanism of relevant element in the residue. The results show that, over 70wt.% of chlorides and nearly 25wt.% of sulfates in the residue could be removed by water washing. Based on an economical consideration, the optimal operation conditions for water washing of APC residue was at liquid/solid (L/S) ratio of 3mL:1g and extracting time of 5min. As expected, the concentrations of Co, Cr, Fe, Ni, V and Cu in the washing effluent increased with time during the washing process. However, the extracting regime differs among different heavy metals. The concentrations of Ba and Mn increased firstly but declined afterwards, and concentrations of Pb and Zn gradually declined while Cd and As kept constant with the increase of extracting time. It is worth mentioning that the bubbling of CO 2 into the washing effluent is promisingly effective for a further removal of Pb, Cu and Zn. Furthermore, kinetic study of the water washing process reveals that the extracting of heavy metals during water washing follows a second-order model. Copyright © 2017 Elsevier Ltd. All rights reserved.

Four weeks of treatment with liraglutide reduces insulin dose without loss of glycemic control in type 1 diabetic patients with and without residual beta-cell function

DEFF Research Database (Denmark)

Kielgast, Urd; Krarup, Thure; Holst, Jens Juul

2011-01-01

OBJECTIVE To investigate the effect of 4 weeks of treatment with liraglutide on insulin dose and glycemic control in type 1 diabetic patients with and without residual ß-cell function. RESEARCH DESIGN AND METHODS Ten type 1 diabetic patients with residual ß-cell function (C-peptide positive) and 19.......1]; P Treatment with liraglutide in type 1 diabetic patients reduces insulin dose with improved or unaltered glycemic control....... activity was performed before (week 0) and during (week 4) treatment. Differences in insulin dose; HbA(1c); time spent with blood glucose 10, and 3.9-9.9 mmol/L; and body weight were evaluated. RESULTS Insulin dose decreased from 0.50 ± 0.06 to 0.31 ± 0.08 units/kg per day (P

Evaluation of residue-residue contact predictions in CASP9

KAUST Repository

Monastyrskyy, Bohdan; Fidelis, Krzysztof; Tramontano, Anna; Kryshtafovych, Andriy

2011-01-01

This work presents the results of the assessment of the intramolecular residue-residue contact predictions submitted to CASP9. The methodology for the assessment does not differ from that used in previous CASPs, with two basic evaluation measures

Stabilization of Rocky Flats combustible residues contaminated with plutonium metal and organic solvents

International Nuclear Information System (INIS)

Bowen, S.M.; Cisneros, M.R.; Jacobson, L.L.; Schroeder, N.C.; Ames, R.L.

1998-01-01

This report describes tests on a proposed flowsheet designed to stabilize combustible residues that were generated at the Rocky Flats Environmental Technology Site (RFETS) during the machining of plutonium metal. Combustible residues are essentially laboratory trash contaminated with halogenated organic solvents and plutonium metal. The proposed flowsheet, designed by RFETS, follows a glovebox procedure that includes (1) the sorting and shredding of materials, (2) a low temperature thermal desorption of solvents from the combustible materials, (3) an oxidation of plutonium metal with steam, and (4) packaging of the stabilized residues. The role of Los Alamos National Laboratory (LANL) in this study was to determine parameters for the low temperature thermal desorption and steam oxidation steps. Thermal desorption of carbon tetrachloride (CCl 4 ) was examined using a heated air stream on a Rocky Flats combustible residue surrogate contaminated with CCl 4 . Three types of plutonium metal were oxidized with steam in a LANL glovebox to determine the effectiveness of this procedure for residue stabilization. The results from these LANL experiments are used to recommend parameters for the proposed RFETS stabilization flowsheet

Decree No. 208 On National Accounting and Control System of the Nuclear Materials

International Nuclear Information System (INIS)

1996-01-01

The present Decree establishes the arrangements to formalize the National Accounting and Control System of the Nuclear Materials, the which one has the objectives of contributing to an efficient and economic management of the nuclear materials in the national territory; to establish the arrangements directed to detect any employment, lost or unauthorized movement of the nuclear material; and to establish the measures of necessary control to give fulfillment to the international commitments assumed by the Cuban State in relationship to the nuclear materials, important components, or both. It also establishes the following responsibilities: The Ministry of Science Technology and Environment is the Organism of the Central Administration of the State responsible for the supervision and control of the dispositions and it delegates in the National Center of Nuclear Security the execution of the functions assigned to this Ministry

The importance of antibiotic residues presence detection in milk

Directory of Open Access Journals (Sweden)

Dubravka Samaržija

2002-01-01

Full Text Available Antibiotic residues are the most present inhibitory substances in milkhaving undesirable effect on human health, technological characteristics and the quality of milk and dairy products. In order to protect consumer's health and to ensure high quality milk production, European Union (EU regulation 2377/90 sets a maximum permitted levels for antibiotic residues in milk. Although the presence of antibiotic residues in milk can be due to animal diseases treatment, and in the case of milking animals, they are mostly present after mastitis treatment. The aim of this work is to stress the importance of the continuous control on antibiotic residues presence in milk, due to the role that milk and dairy products have in human nutrition. In this paper, different groups of antibiotics, mechanisms of theirs action, mistakes occurring in dairy products manufacture as well as the methods for theirs detection are described.

Preferency of soil macrofauna to crops residue at different light intensity

Directory of Open Access Journals (Sweden)

SUGIYARTO

2007-10-01

Full Text Available Every species of soil macrofauna prefer specific food and environment to be establish in it's habitat. Their diversity depend on variation of food and environmental condition. The aim of this research was to study the effect of different crop residue and light intensity on population of several soil macrofauna specieses. Mycrocosmos experiment was arranged in split-plot design with two treatments factor, i.e.: (1 crop residue (albizia, papaya, elephant grass, maize, sweet potato and without crop residue input, and (2 light intensities (0, 5, 15 and 25 Watt/day. The soil macrofauna were earthworms, millipedes, scarabids larvae and cocroachs. Results of the study showed that: (1 crop residues apllication increased soil macrofauna population, especially maize residue ( by 113%, respectively, compare to control tretment, (2 on higher light intensity, population of earthworms, scarabids larvae and cocroach decreased, but population of millipedes increased, (3 the highest macrofauna population was on maize residue and 5 Watt/day light intensity treatment.

Sub-lethal effects of pesticide residues in brood comb on worker honey bee (Apis mellifera development and longevity.

Directory of Open Access Journals (Sweden)

Judy Y Wu

Full Text Available BACKGROUND: Numerous surveys reveal high levels of pesticide residue contamination in honey bee comb. We conducted studies to examine possible direct and indirect effects of pesticide exposure from contaminated brood comb on developing worker bees and adult worker lifespan. METHODOLOGY/PRINCIPAL FINDINGS: Worker bees were reared in brood comb containing high levels of known pesticide residues (treatment or in relatively uncontaminated brood comb (control. Delayed development was observed in bees reared in treatment combs containing high levels of pesticides particularly in the early stages (day 4 and 8 of worker bee development. Adult longevity was reduced by 4 days in bees exposed to pesticide residues in contaminated brood comb during development. Pesticide residue migration from comb containing high pesticide residues caused contamination of control comb after multiple brood cycles and provided insight on how quickly residues move through wax. Higher brood mortality and delayed adult emergence occurred after multiple brood cycles in contaminated control combs. In contrast, survivability increased in bees reared in treatment comb after multiple brood cycles when pesticide residues had been reduced in treatment combs due to residue migration into uncontaminated control combs, supporting comb replacement efforts. Chemical analysis after the experiment confirmed the migration of pesticide residues from treatment combs into previously uncontaminated control comb. CONCLUSIONS/SIGNIFICANCE: This study is the first to demonstrate sub-lethal effects on worker honey bees from pesticide residue exposure from contaminated brood comb. Sub-lethal effects, including delayed larval development and adult emergence or shortened adult longevity, can have indirect effects on the colony such as premature shifts in hive roles and foraging activity. In addition, longer development time for bees may provide a reproductive advantage for parasitic Varroa destructor

Ranking system for national regulatory jurisdictions based on pesticide standard values in major exposures

Directory of Open Access Journals (Sweden)

Zijian Li

2017-07-01

Full Text Available To control the risk of human exposure to pesticides, about 50 nations have promulgated pesticide soil regulatory guidance values (RGVs, and 104 nations have provided pesticide drinking water maximum concentration levels (MCLs. In addition, 90 nations have regulated pesticide agricultural commodity maximum residue limits (MRLs. Pesticide standard values (PSVs for one single pesticide varied in a range of six, seven, or even eight orders of magnitude. Some PSVs are too large to prevent the impact of pesticides on human health. Many nations have not provided PSVs for some commonly used pesticides until now. This research has introduced several completeness values and numerical values methods to evaluate the national jurisdiction’s performance on PSVs on a nation base. The national jurisdiction ranking system developed by these methods will be beneficial to the environmental regulation makers in the management of PSVs. Results also indicate that European countries perform better in the regulation of pesticide soil RGVs, drinking water MCLs, and agricultural commodity MRLs.

Quality-control design for surface-water sampling in the National Water-Quality Network

Science.gov (United States)

Riskin, Melissa L.; Reutter, David C.; Martin, Jeffrey D.; Mueller, David K.

2018-04-10

The data-quality objectives for samples collected at surface-water sites in the National Water-Quality Network include estimating the extent to which contamination, matrix effects, and measurement variability affect interpretation of environmental conditions. Quality-control samples provide insight into how well the samples collected at surface-water sites represent the true environmental conditions. Quality-control samples used in this program include field blanks, replicates, and field matrix spikes. This report describes the design for collection of these quality-control samples and the data management needed to properly identify these samples in the U.S. Geological Survey’s national database.

76 FR 67790 - National Express Acquisition Corporation-Control-Petermann Partners, Inc.

Science.gov (United States)

2011-11-02

... application under 49 U.S.C. 14303 for NEAC's acquisition of control of Petermann Partners, Inc. (PPI), a... oppose the application must follow the rules under 49 CFR 1182.5 and 1182.8. DATES: Comments must be... Corporation, National Express Group, PLC, controls NEC and NEAC, both of which are noncarrier holding...

Influence of organic waste and residue mud additions on chemical, physical and microbial properties of bauxite residue sand.

Science.gov (United States)

Jones, Benjamin E H; Haynes, Richard J; Phillips, Ian R

2011-02-01

wet sieving, was greatest where poultry manure was applied. Although total organic C and soluble organic C were greater in biosolids than poultry manure treatments, the reverse was the case for microbial biomass C and basal respiration. In the biosolids and poultry manure treatments, increasing residue mud additions tended to increase soluble C, microbial biomass C and basal respiration. Germination index of watercress was highest in control samples and reduced by additions of biosolids and poultry manure which was attributed to the high EC and possibly high extractable P and NH (4) (+) . The concurrent addition of residue mud and organic wastes can improve chemical, microbial and particularly physical properties of residue sand. Future research should include neutralisation of the mud (e.g. with gypsum) and subsequent leaching to remove salts originating from both the mud and organic wastes.

Agricultural Residues and Biomass Energy Crops

Energy Technology Data Exchange (ETDEWEB)

None

2016-06-01

There are many opportunities to leverage agricultural resources on existing lands without interfering with production of food, feed, fiber, or forest products. In the recently developed advanced biomass feedstock commercialization vision, estimates of potentially available biomass supply from agriculture are built upon the U.S. Department of Agriculture’s (USDA’s) Long-Term Forecast, ensuring that existing product demands are met before biomass crops are planted. Dedicated biomass energy crops and agricultural crop residues are abundant, diverse, and widely distributed across the United States. These potential biomass supplies can play an important role in a national biofuels commercialization strategy.

The Ising model for prediction of disordered residues from protein sequence alone

International Nuclear Information System (INIS)

Lobanov, Michail Yu; Galzitskaya, Oxana V

2011-01-01

Intrinsically disordered regions serve as molecular recognition elements, which play an important role in the control of many cellular processes and signaling pathways. It is useful to be able to predict positions of disordered residues and disordered regions in protein chains using protein sequence alone. A new method (IsUnstruct) based on the Ising model for prediction of disordered residues from protein sequence alone has been developed. According to this model, each residue can be in one of two states: ordered or disordered. The model is an approximation of the Ising model in which the interaction term between neighbors has been replaced by a penalty for changing between states (the energy of border). The IsUnstruct has been compared with other available methods and found to perform well. The method correctly finds 77% of disordered residues as well as 87% of ordered residues in the CASP8 database, and 72% of disordered residues as well as 85% of ordered residues in the DisProt database

Location of external state financial control in national control system of Ukraine

Directory of Open Access Journals (Sweden)

N.G. Vygovska

2016-12-01

Full Text Available The article estimates the theoretical basis of the external state financial control in Ukraine in the context of defining its place in the formation of the functional areas of internal and external controls in order to eliminate duplication of a single national control system. The authors have investigated the scientific approaches to the interpretation of the concept of «external state financial control», «internal financial control», «public audit» in order to eliminate terminological confusion. It were found the differences between the external and internal financial control on the basis of comparative characteristics of such features as the entity controlling entities, controlled objects, object methods, and direction control. The concept of internal and external controls are considered to expedient to communicate with the system in which this control is identified. «Internal» in this case is identical intra-control, that is located within the executive branch, while an external control is not included in it and is external to the executive bodies of the controlled institution, and is not related to them and, as a consequence, independent. The authors suggest to form a unified system of state financial control, a clear distinction between internal and external powers of species. The authors consider that appropriate in this context will be the adoption of a single legislative act «About State Financial Control», the proposed structure is introduced in the article. Implementation of this law will contribute to the clear division of functional areas of the state control (internal and external, the elimination of departmental conflicts, and promote the formation of a single integrated control system in Ukraine, able to counteract abuses and prevent the possible loss of budgetary funds.

[Is it necessary to control the population growth of national minorities].

Science.gov (United States)

Tian, X Y

1981-02-01

In the process of Socialist construction and modernization, the development of the population of national minorities deserves our attention because it is directly related to the economic and cultural development in the areas inhabited by such national minorities, and it has a great impact on the welfare and future of those people. Moreover, the population growth of the minorities is a key factor in the national population control strategy. A rapid population growth among the minorities has caused serious problems in distribution of farm land and food supply, low personal income, a rise in the unemployment rate, and a rise in the illiteracy rate. This has prevented a rise in the living standard among the minority population. In order to prevent and solve population problems among the minorities, we must take appropriate measures according to local conditions to control population increases. Through popularization of education, population growth may be put under control. For those people who volunteer to practice family planning, the government should provide all kinds of assistance. At the same time, an effort is needed to introduce the necessity of improving birth quality, to popularize new methods of child birth, and to develop health and medical care for the general public, so that the quality of the minority population may be gradually improved.

Presence of pesticide residues on produce cultivated in Suriname.

Science.gov (United States)

Abdoel Wahid, F; Wickliffe, J; Wilson, M; Van Sauers, A; Bond, N; Hawkins, W; Mans, D; Lichtveld, M

2017-06-01

Agricultural pesticides are widely used in Suriname, an upper middle-income Caribbean country located in South America. Suriname imported 1.8 million kg of agricultural pesticides in 2015. So far, however, national monitoring of pesticides in crops is absent. Reports from the Netherlands on imported Surinamese produce from 2010 to 2015 consistently showed that samples exceeded plant-specific pesticide maximum residue limits (MRLs) of the European Union (EU). Consumption of produce containing unsafe levels of pesticide residues can cause neurological disorders, and particularly, pregnant women and children may be vulnerable. This pilot study assessed the presence of pesticide residues in commonly consumed produce items cultivated in Suriname. Thirty-two insecticides (organophosphates, organochlorines, carbamates, and pyrethroids) and 12 fungicides were evaluated for their levels in nine types of produce. Pesticide residue levels exceeding MRLs in this study regarded cypermethrin (0.32 μg/g) in tomatoes (USA MRL 0.20 μg/g), lambda-cyhalothrin (1.08 μg/g) in Chinese cabbage (USA MRL 0.40 μg/g), endosulfan (0.07 μg/g) in tannia (EU MRL 0.05 μg/g), and lindane (0.02 and 0.03 μg/g, respectively) in tannia (EU MRL 0.01 μg/g). While only a few pesticide residues were detected in this small pilot study, these residues included two widely banned pesticides (endosulfan and lindane). There is a need to address environmental policy gaps. A more comprehensive sampling and analysis of produce from Suriname is warranted to better understand the scope of the problem. Preliminary assessments, using intake rate, hazard quotient, and level of concern showed that it is unlikely that daily consumption of tannia leads to adverse health effects.

Residual life management. Maintenance improvement

International Nuclear Information System (INIS)

Sainero Garcia, J.; Hevia Ruperez, F.

1995-01-01

The terms Residual Life Management, Life Cycle Management and Long-Term Management are synonymous with a concept which aims to establish efficient maintenance for the profitable and safe operation of a power plant for as long as possible. A Residual Life Management programme comprises a number of stages, of which Maintenance Evaluation focuses on how power plant maintenance practices allow the mitigation and control of component ageing. with this objective in mind, a methodology has been developed for the analysis of potential degradative phenomena acting on critical components in terms of normal power plant maintenance practices. This methodology applied to maintenance evaluation enables the setting out of a maintenance programme based on the Life Management concept, and the programme's subsequent up-dating to allow for new techniques and methods. Initial applications have shown that although, in general terms, power plant maintenance is efficient, the way in which Residual Life Management is approached requires changes in maintenance practices. These changes range from modifications to existing inspection and surveillance methods or the establishment of new ones, to the monitoring of trends or the performance of additional studies, the purpose of which is to provide an accurate evaluation of the condition of the installations and the possibility of life extension. (Author)

Residue and bio-efficacy evaluation of controlled release formulations of imidacloprid against pests in soybean (Glycine max).

Science.gov (United States)

Adak, Totan; Kumar, Jitendra; Dey, Debjani; Shakil, N A; Walia, S

2012-01-01

Controlled release (CR) formulations of imidacloprid (1-(6 chloro-3-pyridinyl methyl)-N- nitro imidazolidin-2- ylideneamine) were prepared using novel amphiphilic polymers synthesized from polyethylene glycol and aliphatic diacids employing encapsulation technique. The bioefficacy of the prepared CR formulations was evaluated against major pests of soybean, namely stem fly, Melanagromyza sojae Zehntmer and white fly, Bemisia tabaci Gennadius along with a commercial formulation at the experimental farm of Indian Agricultural Research Institute (IARI), New Delhi during kharif 2009 and 2010. Most of the CR formulations of imidacloprid gave significantly better control of the pests compare to its commercial formulations, however the CR formulations, Poly [poly (oxyethylene-1000)-oxy suberoyl] amphiphilic polymer based formulation performed better over others for controlling of both stem fly incidence and Yellow Mosaic Virus (YMV) infestation transmitted by white fly. Some of the developed CR formulations recorded higher yield over commercial formulation and control. Nodulation pattern of soybean was not affected due to treatment of CR and commercial formulations of imidacloprid. Also the residues of imidacloprid in seed and soil at harvest were not detectable for both CR and commercial formulations.

Bulging of cans containing plutonium residues. Summary report

International Nuclear Information System (INIS)

Van Konynenburg, R.A.; Wood, D.H.; Condit, R.H.; Shikany, S.D.

1996-03-01

In 1994, two cans in the Lawrence Livermore National Laboratory Plutonium Facility were found to be bulging as a result of the generation of gases form the plutonium ash residues contained in the cans. This report describes the chronology of this discovery, the response actions that revealed other pressurized cans, the analysis of the causes, the short-term remedial action, a followup inspection of the short-term storage packages, and a review of proposed long-term remedial options

Rigid Residue Scan Simulations Systematically Reveal Residue Entropic Roles in Protein Allostery.

Directory of Open Access Journals (Sweden)

Robert Kalescky

2016-04-01

Full Text Available Intra-protein information is transmitted over distances via allosteric processes. This ubiquitous protein process allows for protein function changes due to ligand binding events. Understanding protein allostery is essential to understanding protein functions. In this study, allostery in the second PDZ domain (PDZ2 in the human PTP1E protein is examined as model system to advance a recently developed rigid residue scan method combining with configurational entropy calculation and principal component analysis. The contributions from individual residues to whole-protein dynamics and allostery were systematically assessed via rigid body simulations of both unbound and ligand-bound states of the protein. The entropic contributions of individual residues to whole-protein dynamics were evaluated based on covariance-based correlation analysis of all simulations. The changes of overall protein entropy when individual residues being held rigid support that the rigidity/flexibility equilibrium in protein structure is governed by the La Châtelier's principle of chemical equilibrium. Key residues of PDZ2 allostery were identified with good agreement with NMR studies of the same protein bound to the same peptide. On the other hand, the change of entropic contribution from each residue upon perturbation revealed intrinsic differences among all the residues. The quasi-harmonic and principal component analyses of simulations without rigid residue perturbation showed a coherent allosteric mode from unbound and bound states, respectively. The projection of simulations with rigid residue perturbation onto coherent allosteric modes demonstrated the intrinsic shifting of ensemble distributions supporting the population-shift theory of protein allostery. Overall, the study presented here provides a robust and systematic approach to estimate the contribution of individual residue internal motion to overall protein dynamics and allostery.

DEFECT MONITORING IN IRON CASTING USING RESIDUES OF AUTOREGRESSIVE MODELS

Directory of Open Access Journals (Sweden)

Vanusa Andrea Casarin

2013-06-01

Full Text Available The purpose of this study is to monitor the index of general waste irons forecasting nodular and gray using the residues originated from the methodology Box & Jenkins by means of X-bar and R control charts. Search is to find a general class of model ARIMA (p, d, q but as data have autocorrelation is found to the number of residues which allowed the application of charts. The found model was the model SARIMA (0,1,1(0,1,1 . In step of checking the stability of the model was found that some comments are out of control due to temperature and chemical composition.

Food toxicology. Residues and contaminants: Risks and consumer protection; Lebensmitteltoxikologie. Rueckstaende und Kontaminanten: Risiken und Verbraucherschutz

Energy Technology Data Exchange (ETDEWEB)

Nau, H. [Tieraerztliche Hochschule Hannover, ZA Lebensmitteltoxikologie (Germany); Steinberg, P. [Potsdam Univ., Inst. fuer Ernaehrungswissenschaft (Germany); Kietzmann, M. (eds.) [Tieraerztliche Hochschule Hannover, Inst. fuer Pharmakologie, Toxikologie/Pharmazie (Germany)

2003-07-01

In a detailed introduction, the basic methods of risk assessment for potentially toxic food constituents are presented as well as the analytical methods applied for measuring even very small concentrations of contaminants. The main classes of substances relevant in foods ar represented, i.e. animal drugs, fungicides and herbicides, natural toxins, contaminants, prions from BSE-infested animals and residues of 'new' proteins and 'new' DNA from genetically modified foods. New legislation in Germany and Europe is presented including the National Residue Monitoring Plant which is to enable annual monitoring of residue concentrations in foods derived from animals. (orig.)

Detection of residues antibiotics in food using a microbiological method

International Nuclear Information System (INIS)

Ben Ali, Ahmed

2007-01-01

Antibiotics are effective therapeutic agents because of their property of selective bacterial toxicity which helps controlling infections. Animals, just like humans, can be treated with antibiotics. This use of antibiotics can lead to the development of resistance. Resistant strains may cause severe infections in humans and animals. In addition, antibiotic residues might represent a problem for human health. Our objective is to develop a microbiological method for the detection of antibiotic residues in poultry(muscle, liver,...). For this purpose, antibiotic sensitive bacteria and selective agar media were used. An inhibition growth zone surrounds each of the food samples containing antibiotic residues after a prescribed incubation time. (Author). 23 refs

Effects of relative density and accumulated shear strain on post-liquefaction residual deformation

Directory of Open Access Journals (Sweden)

J. Kim

2013-10-01

Full Text Available The damage caused by liquefaction, which occurs following an earthquake, is usually because of settlement and lateral spreading. Generally, the evaluation of liquefaction has been centered on settlement, that is, residual volumetric strain. However, in actual soil, residual shear and residual volumetric deformations occur simultaneously after an earthquake. Therefore, the simultaneous evaluation of the two phenomena and the clarification of their relationship are likely to evaluate post-liquefaction soil behaviors more accurately. Hence, a quantitative evaluation of post-liquefaction damage will also be possible. In this study, the effects of relative density and accumulated shear strain on post-liquefaction residual deformations were reviewed through a series of lateral constrained-control hollow cylindrical torsion tests under undrained conditions. In order to identify the relationship between residual shear and residual volumetric strains, this study proposed a new test method that integrates monotonic loading after cyclic loading, and K0-drain after cyclic loading – in other words, the combination of cyclic loading, monotonic loading, and the K0 drain. In addition, a control that maintained the lateral constrained condition across all the processes of consolidation, cyclic loading, monotonic loading, and drainage was used to reproduce the anisotropy of in situ ground. This lateral constrain control was performed by controlling the axial strain, based on the assumption that under undrained conditions, axial and lateral strains occur simultaneously, and unless axial strain occurs, lateral strain does not occur. The test results confirmed that the recovery of effective stresses, which occur during monotonic loading and drainage after cyclic loading, respectively, result from mutually different structural restoration characteristics. In addition, in the ranges of 40–60% relative density and 50–100% accumulated shear strain, relative

Toxicity and residual control of Plutella xylostella L. (Lepidoptera: Plutellidae with Bacillus thuringiensis Berliner and insecticides Toxicidade e controle residual de Plutella xylostella L. (Lepidoptera: Plutellidae com Bacillus thuringiensis Berliner e inseticidas

Directory of Open Access Journals (Sweden)

Carla Pedroso de Moraes

2012-08-01

Full Text Available Plutella xylostella L. is the most important worldwide pest of cruciferous plants and indiscriminate use of insecticides has led to the resistance of the species to different groups. This research was conducted to compare the toxicity and persistence of two strains of Bacillus thuringiensis to P. xylostella larvae. Concentrations between 125 and 500g 100L-1 of water of the commercial products were evaluated and compared to the insect growth inhibitor diflubenzuron and to the neurotoxic pyrethroid deltamethrin. The efficacy of the insecticides was compared between treated plants kept indoor greenhouse and outdoor. Third instar larvae were more susceptible to B. thuringiensis than first instar ones. Agree and Dipel showed similar control rates of third instars until 10 days after treatment, but on the 15th day, Agree was significantly more efficient than Dipel. Both B. thuringiensis formulations showed a reduction in mortality after 10 days when the treated plants were exposed to natural weather conditions in comparison to the same treatments kept inside greenhouse. Dimilin (100g 100L-1 of water and deltamethrin (30ml of commercial product 100L-1 of water were not efficient to control third instar larvae of P. xylostella. This inefficiency cannot be attributed to a resistant population of P. xylostella since the larval population used in the experiments was not subjected to insecticide pressure, once the crop was organically cultivated all year round. The results showed that both formulations of B. thuringiensis are sound alternatives for the control of the diamondback moth in organically conducted cruciferous crops, considering the high residual control provided under subtropical weather conditions.Larvas de Plutella xylostella L. são as principais pragas de crucíferas cultivadas e o uso excessivo e indiscriminado de inseticidas tem levado a resistência da espécie para diferentes grupos de inseticidas. Este trabalho foi conduzido para

Measurement of edge residual stresses in glass by the phase-shifting method

Science.gov (United States)

Ajovalasit, A.; Petrucci, G.; Scafidi, M.

2011-05-01

Control and measurement of residual stress in glass is of great importance in the industrial field. Since glass is a birefringent material, the residual stress analysis is based mainly on the photoelastic method. This paper considers two methods of automated analysis of membrane residual stress in glass sheets, based on the phase-shifting concept in monochromatic light. In particular these methods are the automated versions of goniometric compensation methods of Tardy and Sénarmont. The proposed methods can effectively replace manual methods of compensation (goniometric compensation of Tardy and Sénarmont, Babinet and Babinet-Soleil compensators) provided by current standards on the analysis of residual stresses in glasses.

Thermal treatment system of hazardous residuals in three heating zones based on a microprocessor

International Nuclear Information System (INIS)

Luna H, C.L.

1997-01-01

Thermal treatment system consists of a high power electric oven of three heating zones where each zone works up to 1200 Centigrades; it has the capacity of rising the central zone temperature up to 1000 Centigrades in 58 minutes approximately. This configuration of three zones could be programmed to different temperatures and they will be digitally controlled by a control microprocessor, which has been controlled by its own assembler language, in function of the PID control. There are also other important controls based on this microprocessor, as a signal amplification, starting and shutdown of high power step relays, activation and deactivation of both analogic/digital and digital/analogic convertors, port activation and basic data storage of the system. Two main characteristics were looked for this oven design; the first was the possibility of controlling the three zone temperature and the second was to reduce the rising and stabilization operation time and its digitized control. The principal function of the three zone oven is to accelerate the degradation of hazardous residuals by an oxidation instead combustion, through relatively high temperatures (minimum 800 Centigrades and maximum 1200 Centigrades); this process reduces the ash and volatile particulate production. The hazardous residuals will be pumped into the degradation system and after atomized through a packaged column; this step will avoid the direct contact of the residuals with the oven cores. These features make this system as closed process, which means that the residuals can not leak to the working area, reducing the exposure risk to the personnel. This three step oven system is the first stage of the complete hazardous residuals degradation system; after this, the flow will go into a cold plasma region where the process is completed, making a closed system. (Author)

THE CYBERSECURITY OF AUTOMATED CONTROL SYSTEMS AS A KEY COMPONENT OF NATIONAL SECURITY

Directory of Open Access Journals (Sweden)

Galin R. Ivanov

2016-10-01

Full Text Available This article focuses on the current problems raised by the necessity to provide and ensure national cybersecurity. Moreover, it suggests measures for adequate counteraction to present-day cyber threats to automated control systems employed in the sector of national security.

Aging assessment of Residual Heat Removal systems in Boiling Water Reactors

International Nuclear Information System (INIS)

Lofaro, R.J.; Aggarwal, S.

1992-01-01

The effects of aging on Residual Heat Removal systems in Boiling Water Reactors have been studied as part of the Nuclear Plant Aging Research Program. The aging phenomena has been characterized by analyzing operating experience from various national data bases. In addition, actual plant data was obtained to supplement and validate the data base findings

Pesticide residues in birds and mammals

Science.gov (United States)

Stickel, L.F.; Edwards, C.A.

1973-01-01

SUMMARY: Residues of organochlorine pesticides and their breakdown products are present in the tissues of essentially all wild birds throughout the world. These chemicals accumulate in fat from a relatively small environmental exposure. DDE and dieldrin are most prevalent. Others, such as heptachlor epoxide, chlordane, endrin, and benzene hexachloride also occur, the quantities and kinds generally reflecting local or regional use. Accumulation may be sufficient to kill animals following applications for pest control. This has occurred in several large-scale programmes in the United States. Mortality has also resulted from unintentional leakage of chemical from commercial establishments. Residues may persist in the environment for many years, exposing successive generations of animals. In general, birds that eat other birds, or fish, have higher residues than those that eat seeds and vegetation. The kinetic processes of absorption, metabolism, storage, and output differ according to both kind of chemical and species of animal. When exposure is low and continuous, a balance between intake and excretion may be achieved. Residues reach a balance at an approximate animal body equilibrium or plateau; the storage is generally proportional to dose. Experiments with chickens show that dieldrin and heptachlor epoxide have the greatest propensity for storage, endrin next, then DDT, then lindane. The storage of DDT was complicated by its metabolism to DDE and DDD, but other studies show that DDE has a much greater propensity for storage than either DDD or DDT. Methoxychlor has little cumulative capacity in birds. Residues in eggs reflect and parallel those in the parent bird during accumulation, equilibrium, and decline when dosage is discontinued. Residues with the greatest propensity for storage are also lost most slowly. Rate of loss of residues can be modified by dietary components and is speeded by weight loss of the animal. Under sublethal conditions of continuous

Benchmarking residual dose rates in a NuMI-like environment

Energy Technology Data Exchange (ETDEWEB)

Igor L. Rakhno et al.

2001-11-02

Activation of various structural and shielding materials is an important issue for many applications. A model developed recently to calculate residual activity of arbitrary composite materials for arbitrary irradiation and cooling times is presented in the paper. Measurements have been performed at the Fermi National Accelerator Laboratory using a 120 GeV proton beam to study induced radioactivation of materials used for beam line components and shielding. The calculated residual dose rates for the samples studied behind the target and outside of the thick shielding are presented and compared with the measured ones. Effects of energy spectra, sample material and dimensions, their distance from the shielding, and gaps between the shielding modules and walls as well as between the modules themselves were studied in detail.

Genetic control of residual variance of yearling weight in nellore beef cattle

NARCIS (Netherlands)

Iung, L.H.S.; Neves, H.H.R.; Mulder, H.A.; Carvalheiro, R.

2017-01-01

There is evidence for genetic variability in residual variance of livestock traits, which offers the potential for selection for increased uniformity of production. Different statistical approaches have been employed to study this topic; however, little is known about the concordance between

The National System for quality control and the European experience

International Nuclear Information System (INIS)

Dimov, A.; Vassileva, J.; Ingilizova, K.; Slavchev, A. and others

2003-01-01

Objective: The aim of the work is to present the structure and functions of the National System for quality control (NSQC) in the medical irradiation, created to guarantee the safety and the safe use of the radiological equipment. Material and method: The approaches are studies in the development of the NSQC, applied in Bulgaria and some European Union members - such as Germany and Great Britain - and the specifics of the way in which the Directive for medical irradiation EURATOM 97/43 is implemented in national legislations. Results: The advantages and disadvantages of Bulgarian NSQC are analysed and some ideas for tis improvement are suggested. Conclusions: The developed draft NSQC for medical irradiation is in compliance with the requirement of the European Directive. The real advantages and disadvantages of the NSQC will show after its implementation in the practical radiation protection and control in the country

Characteristics and metal leachability of incinerated sewage sludge ash and air pollution control residues from Hong Kong evaluated by different methods.

Science.gov (United States)

Li, Jiang-Shan; Xue, Qiang; Fang, Le; Poon, Chi Sun

2017-06-01

The improper disposal of incinerated sewage sludge ash (ISSA) and air pollution control residues (APCR) from sewage sludge incinerators has become an environmental concern. The physicochemical, morphological and mineralogical characteristics of ISSA and APCR from Hong Kong, and the leachability and risk of heavy metals, are presented in this paper. The results showed that a low hydraulic and pozzolanic potential was associated with the ISSA and APCR due to the presence of low contents of SiO 2 , Al 2 O 3 and CaO and high contents of P, S and Cl (especially for APCR). Although high concentrations of Zn and Cu (especially for ISSA) followed by Ni, Pb and As, Se were detected, a low leaching rate of these metals (especially at neutral and alkaline pH) rendered them classifiable as non-hazardous according to the U.S. EPA and Chinese national regulatory limits. The leached metals concentrations from ISSA and APCR were mainly pH dependent, and metals solubilization occurred mainly at low pH. Different leaching tests should be adopted based on the simulated different environmental conditions and exposure scenarios for assessing the leachability as contrasting results could be obtained due to the differences in complexing abilities and final pH of the leaching solutions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Boron and Coumaphos Residues in Hive Materials Following Treatments for the Control of Aethina tumida Murray.

Directory of Open Access Journals (Sweden)

Cesar Valdovinos-Flores

Full Text Available In the search of alternatives for controlling Aethina tumida Murray, we recently proposed the BAA trap which uses boric acid and an attractant which mimics the process of fermentation caused by Kodamaea ohmeri in the hive. This yeast is excreted in the feces of A. tumida causing the fermentation of pollen and honey of infested hives and releasing compounds that function as aggregation pheromones to A. tumida. Since the boron is the toxic element in boric acid, the aim of this article is to assess the amount of boron residues in honey and beeswax from hives treated with the BAA trap. For this aim, the amount of bioaccumulated boron in products of untreated hives was first determined and then compared with the amount of boron of products from hives treated with the BAA trap in two distinct climatic and soil conditions. The study was conducted in the cities of Padilla, Tamaulipas, and Valladolid, Yucatan (Mexico from August 2014 to March 2015. The quantity of boron in honey was significantly less in Yucatan than in Tamaulipas; this agrees with the boron deficiency among Luvisol and Leptosol soils found in Yucatan compared to the Vertisol soil found in Tamaulipas. In fact, the honey from Yucatan has lower boron levels than those reported in the literature. The BAA treatment was applied for four months, results show that the BAA trap does not have any residual effect in either honey or wax; i.e., there is no significant difference in boron content before and after treatment. On the other hand, the organophosphate pesticide coumaphos was found in 100% of wax samples and in 64% of honey samples collected from Yucatan. The concentration of coumaphos in honey ranges from 0.005 to 0.040 mg/kg, which are below Maximum Residue Limit (MRL allowed in the European Union (0.1 mg/kg but 7.14% of samples exceeded the MRL allowed in Canada (0.02 mg/kg.

Boron and Coumaphos Residues in Hive Materials Following Treatments for the Control of Aethina tumida Murray

Science.gov (United States)

Valdovinos-Flores, Cesar; Gaspar-Ramírez, Octavio; Heras–Ramírez, María Elena; Dorantes-Ugalde, José Antonio; Saldaña-Loza, Luz María

2016-01-01

In the search of alternatives for controlling Aethina tumida Murray, we recently proposed the BAA trap which uses boric acid and an attractant which mimics the process of fermentation caused by Kodamaea ohmeri in the hive. This yeast is excreted in the feces of A. tumida causing the fermentation of pollen and honey of infested hives and releasing compounds that function as aggregation pheromones to A. tumida. Since the boron is the toxic element in boric acid, the aim of this article is to assess the amount of boron residues in honey and beeswax from hives treated with the BAA trap. For this aim, the amount of bioaccumulated boron in products of untreated hives was first determined and then compared with the amount of boron of products from hives treated with the BAA trap in two distinct climatic and soil conditions. The study was conducted in the cities of Padilla, Tamaulipas, and Valladolid, Yucatan (Mexico) from August 2014 to March 2015. The quantity of boron in honey was significantly less in Yucatan than in Tamaulipas; this agrees with the boron deficiency among Luvisol and Leptosol soils found in Yucatan compared to the Vertisol soil found in Tamaulipas. In fact, the honey from Yucatan has lower boron levels than those reported in the literature. The BAA treatment was applied for four months, results show that the BAA trap does not have any residual effect in either honey or wax; i.e., there is no significant difference in boron content before and after treatment. On the other hand, the organophosphate pesticide coumaphos was found in 100% of wax samples and in 64% of honey samples collected from Yucatan. The concentration of coumaphos in honey ranges from 0.005 to 0.040 mg/kg, which are below Maximum Residue Limit (MRL) allowed in the European Union (0.1 mg/kg) but 7.14% of samples exceeded the MRL allowed in Canada (0.02 mg/kg). PMID:27092938

Residual gas analysis

International Nuclear Information System (INIS)

Berecz, I.

1982-01-01

Determination of the residual gas composition in vacuum systems by a special mass spectrometric method was presented. The quadrupole mass spectrometer (QMS) and its application in thin film technology was discussed. Results, partial pressure versus time curves as well as the line spectra of the residual gases in case of the vaporization of a Ti-Pd-Au alloy were demonstrated together with the possible construction schemes of QMS residual gas analysers. (Sz.J.)

National Ignition Facility Control and Information System Operational Tools

International Nuclear Information System (INIS)

Marshall, C.D.; Beeler, R.G.; Bowers, G.A.; Carey, R.W.; Fisher, J.M.; Foxworthy, C.B.; Frazier, T.M.; Mathisen, D.G.; Lagin, L.J.; Rhodes, J.J.; Shaw, M.J.

2009-01-01

The National Ignition Facility (NIF) in Livermore, California, is the world's highest-energy laser fusion system and one of the premier large scale scientific projects in the United States. The system is designed to setup and fire a laser shot to a fusion ignition or high energy density target at rates up to a shot every 4 hours. NIF has 192 laser beams delivering up to 1.8 MJ of energy to a ∼2 mm target that is planned to produce >100 billion atm of pressure and temperatures of >100 million degrees centigrade. NIF is housed in a ten-story building footprint the size of three football fields as shown in Fig. 1. Commissioning was recently completed and NIF will be formally dedicated at Lawrence Livermore National Laboratory on May 29, 2009. The control system has 60,000 hardware controls points and employs 2 million lines of control system code. The control room has highly automated equipment setup prior to firing laser system shots. This automation has a data driven implementation that is conducive to dynamic modification and optimization depending on the shot goals defined by the end user experimenters. NIF has extensive facility machine history and infrastructure maintenance workflow tools both under development and deployed. An extensive operational tools suite has been developed to support facility operations including experimental shot setup, machine readiness, machine health and safety, and machine history. The following paragraphs discuss the current state and future upgrades to these four categories of operational tools.

Assessing the Availability of Wood Residues and Residue Markets in Virginia

OpenAIRE

Alderman, Delton R. Jr.

1998-01-01

A statewide mail survey of primary and secondary wood product manufacturers was undertaken to quantify the production and consumption of wood residues in Virginia. Two hundred and sixty-six wood product manufacturers responded to the study and they provided information on the production, consumption, markets, income or disposal costs, and disposal methods of wood residues. Hardwood and pine sawmills produce approximately 66 percent of Virginia's wood residues. Virginia's wood product man...

A national programme for mastitis control in Australia: Countdown Downunder

Directory of Open Access Journals (Sweden)

Brightling PB

2009-04-01

Full Text Available Abstract In 1998, Countdown Downunder, Australia's national mastitis and cell count control programme, was created. With funding from the country's leading dairy organisation, Dairy Australia, this programme was originally intended to run for three years but is now in its tenth year. As it was the first time Australia had attempted a national approach to mastitis control on the farm, the first three years of the programme were largely concerned with the development of resources to be used by farmers and service providers. The second three years were devoted to training with both groups. Since that time, Countdown Downunder has entered into a second resource development phase. The goal of the programme was to achieve a reduction in the bulk milk somatic cell count from the Australian dairy herd. To achieve this, the programme had to develop resources with clear and consistent messages around mastitis and somatic cell count control on farms. It was determined that progress toward the goals would be made more rapidly if service providers were trained in the use of these resources prior to farmers. This paper reviews the Countdown Downunder programme from 1998 to 2007.

Emission of Carbon Dioxide Influenced by Different Water Levels from Soil Incubated Organic Residues

Science.gov (United States)

Hossain, M. B.; Puteh, A. B.

2013-01-01

We studied the influence of different organic residues and water levels on decomposition rate and carbon sequestration in soil. Organic residues (rice straw, rice root, cow dung, and poultry litter) including control were tested under moistened and flooding systems. An experiment was laid out as a complete randomized design at 25°C for 120 days. Higher CO2-C (265.45 mg) emission was observed in moistened condition than in flooding condition from 7 to 120 days. Among the organic residues, poultry litter produced the highest CO2-C emission. Poultry litter with soil mixture increased 121% cumulative CO2-C compared to control. On average, about 38% of added poultry litter C was mineralized to CO2-C. Maximum CO2-C was found in 7 days after incubation and thereafter CO2-C emission was decreased with the increase of time. Control produced the lowest CO2-C (158.23 mg). Poultry litter produced maximum cumulative CO2-C (349.91 mg). Maximum organic carbon was obtained in cow dung which followed by other organic residues. Organic residues along with flooding condition decreased cumulative CO2-C, k value and increased organic C in soil. Maximum k value was found in poultry litter and control. Incorpored rice straw increased organic carbon and decreased k value (0.003 g d−1) in soil. In conclusion, rice straw and poultry litter were suitable for improving soil carbon. PMID:24163626

Mutational properties of amino acid residues: implications for evolvability of phosphorylatable residues

DEFF Research Database (Denmark)

Creixell, Pau; Schoof, Erwin M.; Tan, Chris Soon Heng

2012-01-01

in terms of their mutational activity. Moreover, we highlight the importance of the genetic code and physico-chemical properties of the amino acid residues as likely causes of these inequalities and uncover serine as a mutational hot spot. Finally, we explore the consequences that these different......; it is typically assumed that all amino acid residues are equally likely to mutate or to result from a mutation. Here, by reconstructing ancestral sequences and computing mutational probabilities for all the amino acid residues, we refute this assumption and show extensive inequalities between different residues...... mutational properties have on phosphorylation site evolution, showing that a higher degree of evolvability exists for phosphorylated threonine and, to a lesser extent, serine in comparison with tyrosine residues. As exemplified by the suppression of serine's mutational activity in phosphorylation sites, our...

Heating oil, distillates and residuals outlook

International Nuclear Information System (INIS)

Ervin, M.J.

2004-01-01

M.J. Ervin and Associates offers strategic planning support to the downstream petroleum industry in terms of price market monitoring, market analysis, media commentary and benchmarking of marketing operations. This presentation included graphs depicting supply and demand for heating oil distillates and residuals from the mid 1990s to 2004. It was noted that the long-term decline in residuals demand in the United States and Canada are due to environmental issues, the use of natural gas as an alternative, and the increasing complexity of refineries. Graphs depicting market impacts of refinery utilization and inventory trends showed that middle distillate production will increase at the expense of gasoline production. Middle distillates and gasoline markets will be more sensitive to supply disruptions, resulting in more frequent price spikes. Inventory trends indicate a greater reliance on product imports. The demand for heating fuel has stabilized due to the continued penetration of natural gas in eastern states and provinces. The demand for diesel fuel has growth 1.5 to 2 per cent while the demand for jet fuel has remained relatively flat and depends greatly on the growth of the gross national product (GNP). tabs., figs

Stabilization of APC residues from waste incineration with ferrous sulfate on a semi-industrial scale

DEFF Research Database (Denmark)

Lundtorp, Kasper; Jensen, Dorthe Lærke; Christensen, Thomas Højlund

2002-01-01

A stabilization method for air pollution control (APC) residues from municipal solid waste incineration (MSWI) involving mixing of the residue with water and FeSO4 has been demonstrated on a semi-industrial scale on three types of APC residues: a semidy (SD) APC residue, a fly ash (FA), and an FA...... mixed with sludge (FAS) from a wet flue gas cleaning system. The process was performed in batches of 165-175 kg residue. It generates a wastewater that is highly saline but has a low content of heavy metals such as Cd, Cr, and Pb. The stabilized and raw residues have been subject to a range of leaching...

Evaluation of the Argonne National Laboratory servo-controlled calorimeter system

International Nuclear Information System (INIS)

Foster, L.A.

1997-01-01

The control system of a replacement mode, twin-bridge, water-bath calorimeter originally built by Mound EG ampersand G Applied Technologies was modified by Argonne National Laboratory. The calorimeter was upgraded with a PC-based computer control and data acquisition system. The system was redesigned to operate in a servo-control mode, and a preheater was constructed to allow pre-equilibration of samples. The instrument was sent to the Plutonium Facility at Los Alamos National Laboratory for testing and evaluation of its performance in the field using heat source standards and plutonium process materials. The important parameters for calorimeter operation necessary to satisfy the nuclear materials control and accountability requirements of the Plutonium Facility were evaluated over a period of several months. These parameters include calorimeter stability, measurement precision and accuracy, and average measurement time. The observed measurement precision and accuracy were found to be acceptable for most accountability measurements, although they were slightly larger than the values for calorimeters in routine use at the Plutonium Facility. Average measurement times were significantly shorter than measurement times for identical items in the Plutonium Facility calorimeters. Unexplained shifts in the baseline measurements were observed on numerous occasions. These shifts could lead to substantial measurement errors if they are not very carefully monitored by the operating facility. Detailed results of the experimental evaluation are presented in this report

The national system of nuclear material control development and challenges. Vol. 3

International Nuclear Information System (INIS)

Badawy, I.

1996-01-01

This paper presents the major factors which may affect the implementation of the National System of Nuclear Material Accounting and Safeguards in Egypt. Developments of this National System-being a division of the Nuclear Regulatory Body in the country-are discussed. Also, recent requirements of the International Atomic Energy Agency within the policy of strengthening its regime of international nuclear control are reviewed. The challenges facing the National System are indicated taking in consideration the anticipated growth in the nuclear field in Egypt by the year 2000 and after. 2 figs

The national system of nuclear material control development and challenges. Vol. 3

Energy Technology Data Exchange (ETDEWEB)

Badawy, I [National Centre for Nuclear Safety and Radiation Control, Atomic Energy Authority, Cairo (Egypt)

1996-03-01

This paper presents the major factors which may affect the implementation of the National System of Nuclear Material Accounting and Safeguards in Egypt. Developments of this National System-being a division of the Nuclear Regulatory Body in the country-are discussed. Also, recent requirements of the International Atomic Energy Agency within the policy of strengthening its regime of international nuclear control are reviewed. The challenges facing the National System are indicated taking in consideration the anticipated growth in the nuclear field in Egypt by the year 2000 and after. 2 figs.

Nevada National Security Site Radiological Control Manual

International Nuclear Information System (INIS)

2012-01-01

This document supersedes DOE/NV/25946--801, 'Nevada Test Site Radiological Control Manual,' Revision 1 issued in February 2010. Brief Description of Revision: A complete revision to reflect a recent change in name for the NTS; changes in name for some tenant organizations; and to update references to current DOE policies, orders, and guidance documents. Article 237.2 was deleted. Appendix 3B was updated. Article 411.2 was modified. Article 422 was re-written to reflect the wording of DOE O 458.1. Article 431.6.d was modified. The glossary was updated. This manual contains the radiological control requirements to be used for all radiological activities conducted by programs under the purview of the U.S. Department of Energy (DOE) and the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO). Compliance with these requirements will ensure compliance with Title 10 Code of Federal Regulations (CFR) Part 835, 'Occupational Radiation Protection.' Programs covered by this manual are located at the Nevada National Security Site (NNSS); Nellis Air Force Base and North Las Vegas, Nevada; Santa Barbara and Livermore, California; and Andrews Air Force Base, Maryland. In addition, fieldwork by NNSA/NSO at other locations is covered by this manual. Current activities at NNSS include operating low-level radioactive and mixed waste disposal facilities for United States defense-generated waste, assembly and execution of subcritical experiments, assembly/disassembly of special experiments, the storage and use of special nuclear materials, performing criticality experiments, emergency responder training, surface cleanup and site characterization of contaminated land areas, environmental activity by the University system, and nonnuclear test operations, such as controlled spills of hazardous materials at the Hazardous Materials Spill Center. Currently, the major potential for occupational radiation exposure is associated with the burial of

Nevada National Security Site Radiological Control Manual

Energy Technology Data Exchange (ETDEWEB)

Radiological Control Managers’ Council

2012-03-26

This document supersedes DOE/NV/25946--801, 'Nevada Test Site Radiological Control Manual,' Revision 1 issued in February 2010. Brief Description of Revision: A complete revision to reflect a recent change in name for the NTS; changes in name for some tenant organizations; and to update references to current DOE policies, orders, and guidance documents. Article 237.2 was deleted. Appendix 3B was updated. Article 411.2 was modified. Article 422 was re-written to reflect the wording of DOE O 458.1. Article 431.6.d was modified. The glossary was updated. This manual contains the radiological control requirements to be used for all radiological activities conducted by programs under the purview of the U.S. Department of Energy (DOE) and the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO). Compliance with these requirements will ensure compliance with Title 10 Code of Federal Regulations (CFR) Part 835, 'Occupational Radiation Protection.' Programs covered by this manual are located at the Nevada National Security Site (NNSS); Nellis Air Force Base and North Las Vegas, Nevada; Santa Barbara and Livermore, California; and Andrews Air Force Base, Maryland. In addition, fieldwork by NNSA/NSO at other locations is covered by this manual. Current activities at NNSS include operating low-level radioactive and mixed waste disposal facilities for United States defense-generated waste, assembly and execution of subcritical experiments, assembly/disassembly of special experiments, the storage and use of special nuclear materials, performing criticality experiments, emergency responder training, surface cleanup and site characterization of contaminated land areas, environmental activity by the University system, and nonnuclear test operations, such as controlled spills of hazardous materials at the Hazardous Materials Spill Center. Currently, the major potential for occupational radiation exposure is associated with the burial of

Unit costs for house spraying and bednet impregnation with residual insecticides in Colombia: a management tool for the control of vector-borne disease.

Science.gov (United States)

Kroeger, A; Ayala, C; Medina Lara, A

2002-06-01

A study of unit costs and cost components of two malaria-control strategies (house spraying and bednet impregnation with residual insecticides) was undertaken in 11 malaria-endemic states (departamentos) of Colombia, using data provided by control staff on self-administered questionnaires. The accuracy of the data was verified by personal visits, telephone conversations and complementary information from 10 other states. Allthe financial-cost components of the malaria-control operations carried out in the previous 6 months and the results of the control operations themselves (including the numbers of houses sprayed and numbers of bednets impregnated/day) were recorded. The information was stratified according to whether the target communities were 'near' or 'far away' from an operational base, the far-away communities being those that needed overnight stays by the control staff. The main variables analysed were unit costs/house treated, and annual cost/person protected. The results show that house spraying was generally more expensive for the health services than bednet impregnation. This is particularly the case in 'nearby' communities, where most of those at-risk live. In such communities, spraying one house was 7.2 times more expensive than impregnating one bednet. Even if only those sleeping under an impregnated net were assumed to be protected, the unit costs/person protected in a 'nearby' community were twice as high for house spraying than for bednet impregnation. In 'nearby' communities, where technicians could return to the operational base each evening, insecticides made up 80% of the total spraying costs and 42% of the costs of bednet impregnation. In 'far-away' communities, however, salaries and 'per diems' were the most important cost components, representing, respectively, 23% and 22% of the costs of spraying, and 34% plus 27% of the costs of impregnation. Insecticide wastage and non-use of discounts on insecticide prices (available through the

Residues of 14C-paclobutrazol in mangoes

International Nuclear Information System (INIS)

Costa, Maria A.; Tornisielo, Valdemar L.; Castanho, Giuliane M.

2009-01-01

Paclobutrazol (PBZ) is a growth regulator used in agricultural systems whose purpose is the control of vegetative growth, stimulating the reproductive capacity of plants. This growth regulator remains active in soil for a long time and its half-life varies with the type of soil and climatic conditions, can severely affect the development of crops. This work aimed to study the residues / metabolites of 14 C-PBZ in mango pulp Tommy Atkins. The tests were performed with mangoes grown in pots stainless steel and application of 14 C-PBZ was performed by the soil projection of the crown, and the mangoes tested in two periods, one year and two years after application. To evaluate the levels of residues of 14 C-PBZ was realize the burning of 200 mg of pulp on biological oxidized and detached 14 CO 2 was detected by liquid scintillation spectrophotometer. The results were 1.65 % of residue of PBZ on fruit collected after two years of application and 4.30 % of residue of PBZ collected on fruit after a year of application and also can see that the product remained in the soil for more than one year, is translocated to the plant and reach the edible part, the pulp fruit. The identification of residual 14 C- PBZ/metabolites by thin-layer chromatography did not reveal any pattern of PBZ / metabolites due to the low activity detected in the samples. Therefore, another procedure was performed for extraction and then analyzed by high performance liquid chromatography (HPLC) for detection of metabolites in the PBZ of mango pulp. (author)

Design electronic of manual control for cobalt unit Alcyon II of the National Center of Radiotherapy

International Nuclear Information System (INIS)

Morraz V, E.; Campos, X.

2002-01-01

A manual control for the cobalt unit, of French production, it was designed by the team of electronic of the national center of radiotherapy with materials found in the national trade. The control has the same characteristics that the original one and it is also adapted a switch from which you can control the lights of the room of the cobalt

Residual concentrations of micropollutants in benthic mussels in the coastal areas of Bohai Sea, North China

International Nuclear Information System (INIS)

Liu Wenxin; Chen Jianglin; Lin Xiumei; Fan Yongsheng; Tao Shu

2007-01-01

Studies of heavy metals and organic pollutants in different benthic mussel species from Bohai Sea show that concentrations of Cd in mussels commonly exceed national biological quality standards. In addition, a site located in Laizhou Bay exhibits higher average concentrations of As, Hg and Pb with respect to the other sites. Residual levels of petroleum hydrocarbons at several sites in Liaodong Bay also exceed quality guidelines. Contents and compositional characteristics of DDT and its metabolites in mussels suggest the probability of recent inputs and potential ecological risks to the local benthic environment. - Residual Cd contents of mussels at many sites in Bohai Sea exceed national marine biological quality standard and compositions of DDT metabolites indicate recent inputs and potential risk

Evaluation of residue-residue contact prediction in CASP10

KAUST Repository

Monastyrskyy, Bohdan

2013-08-31

We present the results of the assessment of the intramolecular residue-residue contact predictions from 26 prediction groups participating in the 10th round of the CASP experiment. The most recently developed direct coupling analysis methods did not take part in the experiment likely because they require a very deep sequence alignment not available for any of the 114 CASP10 targets. The performance of contact prediction methods was evaluated with the measures used in previous CASPs (i.e., prediction accuracy and the difference between the distribution of the predicted contacts and that of all pairs of residues in the target protein), as well as new measures, such as the Matthews correlation coefficient, the area under the precision-recall curve and the ranks of the first correctly and incorrectly predicted contact. We also evaluated the ability to detect interdomain contacts and tested whether the difficulty of predicting contacts depends upon the protein length and the depth of the family sequence alignment. The analyses were carried out on the target domains for which structural homologs did not exist or were difficult to identify. The evaluation was performed for all types of contacts (short, medium, and long-range), with emphasis placed on long-range contacts, i.e. those involving residues separated by at least 24 residues along the sequence. The assessment suggests that the best CASP10 contact prediction methods perform at approximately the same level, and comparably to those participating in CASP9.

Overlapping Residual Herbicides for Control of Photosystem (PS) II- and 4-Hydroxyphenylpyruvate Dioxygenase (HPPD)-Inhibitor-Resistant Palmer amaranth (Amaranthus palmeri S. Watson) in Glyphosate-Resistant Maize

Science.gov (United States)

Chahal, Parminder S.; Ganie, Zahoor A.; Jhala, Amit J.

2018-01-01

A Palmer amaranth (Amaranthus palmeri S. Watson) biotype has evolved resistance to photosystem (PS) II- (atrazine) and 4-hydroxyphenylpyruvate dioxygenase (HPPD)-inhibiting herbicides (mesotrione, tembotrione, and topramezone) in maize seed production field in Nebraska, USA. The objectives of this study were to determine the effect of soil residual pre-emergence (PRE) herbicides followed by (fb) tank-mixture of residual and foliar active post-emergence (POST) herbicides on PS-II- and HPPD-inhibitor-resistant Palmer amaranth control, maize yield, and net economic returns. Field experiments were conducted in a grower's field infested with PS II- and HPPD-inhibitor-resistant Palmer amaranth near Shickley in Fillmore County, Nebraska, USA in 2015 and 2016. The contrast analysis suggested that saflufenacil plus dimethenamid-P or pyroxasulfone plus saflufenacil applied PRE provided 80–82% Palmer amaranth control compared to 65 and 39% control with saflufenacil and pyroxasulfone applied alone at 3 weeks after PRE (WAPRE), respectively. Among the PRE fb POST herbicide programs, 95–98% Palmer amaranth control was achieved with pyroxasulfone plus safluefenacil, or saflufenacil plus dimethenamid-P applied PRE, fb glyphosate plus topramezone plus dimethenamid-P plus atrazine, glyphosate plus diflufenzopyr plus dicamba plus pyroxasulfone, glyphosate plus diflufenzopyr plus pendimethalin, or glyphosate plus diflufenzopyr plus dicamba plus atrazine applied POST at 3 weeks after POST (WAPOST) through maize harvest. Based on contrast analysis, PRE fb POST programs provided 77–83% Palmer amaranth control at 3 WAPOST through maize harvest compared to 12–15% control with PRE-only and 66–84% control with POST-only programs. Similarly, PRE fb POST programs provided 99% biomass reduction at 6 WAPOST compared to PRE-only (28%) and POST-only (87%) programs. PRE fb POST programs provided higher maize yield (13,617 kg ha−1) and net return (US $1,724 ha−1) compared to the PRE

Effect of Residue Nitrogen Concentration and Time Duration on Carbon Mineralization Rate of Alfalfa Residues in Regions with Different Climatic Conditions

Directory of Open Access Journals (Sweden)

saeid shafiei

2017-08-01

-arid (Sardouiyeh. The most suitable temperatures occurred from April to October in arid and semiarid climates and soil moisture is probably the key contributor to the rate of decomposition. The highest carbon loss in alfalfa in the cold, semiarid climate for a period of 8 months was 32.64%. The highest carbon decomposition rate constant was observed in the first 2 months of the incubation time. These results indicate that higher nitrogen residue resulted in greater decomposition of plant residue and lower carbon remaining in all tested climates. The higher nitrogen content of plant residue potentially increases the concentration of nitrogen in crop residue and may increase the decomposition rate. The strong relation between decomposition and climate has led to the belief that favorable climatic conditions can increase the decomposition rate on a global scale and positively decrease and distribute greenhouse gases in the atmosphere. In arid and semi-arid ecosystems, it is difficult to assess the decomposition rate based on climatic data; it seems to be related to temperature and available humidity. Furthermore, Austin & Vivanco (2006 reported that, in semi-arid climates, the litter decomposition rate decreased by 60 % when solar radiation was attenuated; they concluded that photodegradation exerts dominant control over litter decomposition in a dry ecosystem. Conclusions The results showed that, precipitation of the study area and soil moisture played a key role in the plant residue decomposition rate. In the cold semi-arid climate which moisture was available for decomposition of plant residues for a longer period of time, OC loss and decomposition rate constant were higher than those obtained for warm-arid and temperate-arid climatic conditions. It may be concluded that crop fertilization, which increases P and N concentrations of plant residue, increases decomposition rate of plant residue but decrease its mean residence time in soils.

Morphing of geometric composites via residual swelling.

Science.gov (United States)

Pezzulla, Matteo; Shillig, Steven A; Nardinocchi, Paola; Holmes, Douglas P

2015-08-07

Understanding and controlling the shape of thin, soft objects has been the focus of significant research efforts among physicists, biologists, and engineers in the last decade. These studies aim to utilize advanced materials in novel, adaptive ways such as fabricating smart actuators or mimicking living tissues. Here, we present the controlled growth-like morphing of 2D sheets into 3D shapes by preparing geometric composite structures that deform by residual swelling. The morphing of these geometric composites is dictated by both swelling and geometry, with diffusion controlling the swelling-induced actuation, and geometric confinement dictating the structure's deformed shape. Building on a simple mechanical analog, we present an analytical model that quantitatively describes how the Gaussian and mean curvatures of a thin disk are affected by the interplay among geometry, mechanics, and swelling. This model is in excellent agreement with our experiments and numerics. We show that the dynamics of residual swelling is dictated by a competition between two characteristic diffusive length scales governed by geometry. Our results provide the first 2D analog of Timoshenko's classical formula for the thermal bending of bimetallic beams - our generalization explains how the Gaussian curvature of a 2D geometric composite is affected by geometry and elasticity. The understanding conferred by these results suggests that the controlled shaping of geometric composites may provide a simple complement to traditional manufacturing techniques.

Proceedings of the 7. biennial residue-to-revenue residual wood conference 2007

International Nuclear Information System (INIS)

Raulin, J.

2007-01-01

This conference provided information on the highest and best use of residual wood, which is quickly becoming a valuable commodity. Issues concerning forest residues, sawmill wastes, agricultural residues and urban organic materials were discussed along with trends in Canadian surplus mill waste production. The evolving nature and technologies of the biomass business were highlighted with particular focus on how to generate energy and save money through the use of residual wood. Residual wood energy projects and developments in Canada, North America and Europe were outlined along with biomass development in relation to forest fires and insect disturbances. Cogeneration technologies using wood wastes for thermal heat, steam and electricity were also presented, along with transportation fuel technologies for the production of ethanol. It was noted that with the rising cost of energy, the forest industry is seeking energy solutions based on the use of residual wood. The range of economically practical residual wood solutions continues to grow as energy prices increase. The conference was attended by more than 200 delegates from the forest industry, suppliers and government representatives, to discuss policies and procedures currently in place. Industry investment is being stimulated by the potential for biofuels and biochemicals, as well as the co-operation between the forest and energy sectors. The conference featured 23 presentations, of which 12 have been catalogued separately for inclusion in this database. refs., tabs., figs

Prevalence of antimicrobial residues in eggs, tissue and feed samples in the State of Kuwait

International Nuclear Information System (INIS)

Alomirah, H.; Al-Mazeedi, H.; Al-Zenki, S.; Al-Faili, B.; Al-Foudary, M.; Abuzid, A.; Al-Sayed, I.; Sidhu, J.

2007-01-01

A total of 238 locally produced and imported eggs, tissue (meat, poultry and aquacultured fish) and feed and feedstuffs samples were collected at different seasonal periods from different farms and retail outlets in Kuwait and screened for presence of beta-lactams, tetracyclines, sulfonamides, streptomycin, macrolides and chloramphenicol (799 tests) using Charm II system. The results indicated that all of the 222 tests performed on table egg samples were negative for the analyzed antimicrobial residues indicating adherence to the guidelines for microbial use and withdrawal. Similarly, all of the 268 tests performed on tissue samples were negative for the analyzed antimicrobial residues except for chloramphenicol. These chloramphenicol positive samples, all of the 66 tests performed were negative for beta-lactams residues. Out of the 79 feed and feedstuff samples analyzed for teracyclines residues, broiler diet and concentrate samples (5%) were above the tetracyclines MRL (100 ppb.). On the other hands, results have revealed a widespread of sulfonamide residues and to a less extent chloramphenicol in tested feed and feedstuff samples. The Charm II system was reliable for rapid screening of antimicrobial residues. In general, results obtained in our study necessitate more effective and well planned national antimicrobial residues surveillance programs focusing particularly on samples imported from highly risk sources. (author)

The allelopathic effects of three crop residues on the germination ...

African Journals Online (AJOL)

... maize inflorescences showed significant differences when compared to the control. No growth was recorded in the radicle until 96 hrs of the experiment in all the extract – treated seeds from the three crop residues while the control germinated at 72 hours. Keywords: Allelopathy, allelochemical, biomolecules, Sphenostylis ...

Development of technologies for national control of and accountancy for nuclear materials

International Nuclear Information System (INIS)

Choi, Young Myung; Kwack, E. H.; Kim, B. K.

2002-03-01

The aim of this project is to establish a rigid foundation of national safeguards and to develop the new technologies for the nuclear control. This project is composed of four different technologies; 1. Monitoring technology for nuclear materials, 2. Detection technology for a single particle, 3. Safeguards information management technology, 4. Physical protection technology. Various studies such as a remote verification system for CANDU spent fuel in dry storage canister, a spent fuel verification system using an optical fiber scintillator, and development of softwares for safeguards and physical protection were performed in the frist phase('99-'01). As a result of this research, it has been identified that the developed technologies could be a crucial means of the control for the nuclear material and facilities related. We are planing to accomplish a steady national safeguard system in the second phase('02-'06). This research will help to elevate the transparency and credibility in national nuclear activities by improving the relative technologies

Persistent free radicals, heavy metals and PAHs generated in particulate soot emissions and residue ash from controlled combustion of common types of plastic

International Nuclear Information System (INIS)

Valavanidis, Athanasios; Iliopoulos, Nikiforos; Gotsis, George; Fiotakis, Konstantinos

2008-01-01

The production and use of polymeric materials worldwide has reached levels of 150 million tonnes per year, and the majority of plastic materials are discarded in waste landfills where are burned generating toxic emissions. In the present study we conducted laboratory experiments for batch combustion/burning of commercial polymeric materials, simulating conditions of open fire combustion, with the purpose to analyze their emissions for chemical characteristics of toxicological importance. We used common types of plastic materials: poly(vinyl chloride) (PVC), low and high density poly(ethylene) (LDPE, HDPE), poly(styrene) (PS), poly(propylene) (PP) and poly(ethylene terephthalate) (PET). Samples of particulate smoke (soot) collected on filters and residue solid ash produced by controlled burning conditions at 600-750 deg. C are used for analysis. Emissions of particulate matter, persistent free radicals embedded in the carbonaceous polymeric matrix, heavy metals, other elements and PAHs were determined in both types of samples. Results showed that all plastics burned easily generating charred residue solid ash and black airborne particulate smoke. Persistent carbon- and oxygen-centered radicals, known for their toxic effects in inhalable airborne particles, were detected in both particulate smoke emissions and residue solid ash. Concentrations of heavy metals and other elements (determined by Inductively Coupled Plasma Emission Spectrometry, ICP, method) were measured in the airborne soot and residue ash. Toxic heavy metals, such as Pb, Zn, Cr, Ni, and Cd were relatively at were found at low concentrations. High concentrations were found for some lithophilic elements, such as Na, Ca, Mg, Si and Al in particulate soot and residue solid ash. Measurements of PAHs showed that low molecular weight PAHs were at higher concentrations in the airborne particulate soot than in the residue solid ash for all types of plastic. Higher-ringed PAHs were detected at higher

Persistent free radicals, heavy metals and PAHs generated in particulate soot emissions and residue ash from controlled combustion of common types of plastic.

Science.gov (United States)

Valavanidis, Athanasios; Iliopoulos, Nikiforos; Gotsis, George; Fiotakis, Konstantinos

2008-08-15

The production and use of polymeric materials worldwide has reached levels of 150 million tonnes per year, and the majority of plastic materials are discarded in waste landfills where are burned generating toxic emissions. In the present study we conducted laboratory experiments for batch combustion/burning of commercial polymeric materials, simulating conditions of open fire combustion, with the purpose to analyze their emissions for chemical characteristics of toxicological importance. We used common types of plastic materials: poly(vinyl chloride) (PVC), low and high density poly(ethylene) (LDPE, HDPE), poly(styrene) (PS), poly(propylene) (PP) and poly(ethylene terephthalate) (PET). Samples of particulate smoke (soot) collected on filters and residue solid ash produced by controlled burning conditions at 600-750 degrees C are used for analysis. Emissions of particulate matter, persistent free radicals embedded in the carbonaceous polymeric matrix, heavy metals, other elements and PAHs were determined in both types of samples. Results showed that all plastics burned easily generating charred residue solid ash and black airborne particulate smoke. Persistent carbon- and oxygen-centered radicals, known for their toxic effects in inhalable airborne particles, were detected in both particulate smoke emissions and residue solid ash. Concentrations of heavy metals and other elements (determined by Inductively Coupled Plasma Emission Spectrometry, ICP, method) were measured in the airborne soot and residue ash. Toxic heavy metals, such as Pb, Zn, Cr, Ni, and Cd were relatively at were found at low concentrations. High concentrations were found for some lithophilic elements, such as Na, Ca, Mg, Si and Al in particulate soot and residue solid ash. Measurements of PAHs showed that low molecular weight PAHs were at higher concentrations in the airborne particulate soot than in the residue solid ash for all types of plastic. Higher-ringed PAHs were detected at higher

Effect of drying on leaching testing of treated municipal solid waste incineration APC-residues

DEFF Research Database (Denmark)

Hu, Y.; Hyks, Jiri; Astrup, Thomas

2008-01-01

Air-pollution-control (APC) residues from waste incinerators are hazardous waste according to European legislation and must be treated prior to landfilling. Batch and column leaching data determine which type of landfill can receive the treated APC-residues. CEN standards are prescribed...

Assessing the residual risk for transfusion-transmitted infections in the Philippine blood supply.

Science.gov (United States)

Lam, Hilton Y; Belizario, Vicente Y; Juban, Noel R; Alejandria, Marissa M; Castillo-Carandang, Nina; Arcellana-Nuqui, Elizabeth; Mirasol, Ma Angelina; Cordero, Cynthia P; Sison, Olivia T; Rivera, Adovich S

2014-09-01

Due to a USAID-funded study on blood banks, a national policy was instituted in 1994 that set standards for Philippine blood services, promoted voluntary donation, and led to a ban on commercial blood banks. In this follow-up study, we assess the safety of the supply by determining the residual risk for transfusion-transmitted infections (syphilis, hepatitis B and C, HIV). We also identified unsafe facility practices and generated policy recommendations. A 1992 study found that transfusion-ready blood was not safe using the LQAS method (P > 0.05). We found that the 2012 residual risk became 0 to 0.9 percent attributable to the national policy. We noted poor to fair adherence to this policy. We identified unsafe practices such as use of rapid tests and lack of random blood retesting. Training and use of regional networks may improve safety. Despite improvement in safety, facilities complain of funding and logistical issues regarding compliance with the policy.

Robust fault detection of turbofan engines subject to adaptive controllers via a Total Measurable Fault Information Residual (ToMFIR) technique.

Science.gov (United States)

Chen, Wen; Chowdhury, Fahmida N; Djuric, Ana; Yeh, Chih-Ping

2014-09-01

This paper provides a new design of robust fault detection for turbofan engines with adaptive controllers. The critical issue is that the adaptive controllers can depress the faulty effects such that the actual system outputs remain the pre-specified values, making it difficult to detect faults/failures. To solve this problem, a Total Measurable Fault Information Residual (ToMFIR) technique with the aid of system transformation is adopted to detect faults in turbofan engines with adaptive controllers. This design is a ToMFIR-redundancy-based robust fault detection. The ToMFIR is first introduced and existing results are also summarized. The Detailed design process of the ToMFIRs is presented and a turbofan engine model is simulated to verify the effectiveness of the proposed ToMFIR-based fault-detection strategy. Copyright © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

MICROBIOLOGICAL EVALUATION OF ANTIBIOTIC RESIDUES IN MEAT, MILK AND EGGS

Directory of Open Access Journals (Sweden)

Abdul Jabbar

2013-04-01

Full Text Available Microbiological tests are widely used to detect antibiotic residues in the meat, milk and eggs for better care of the quality and health safety. In the present study microbiological inhibition test i.e. Swab Test on Animal Food (STAF was developed indigenously for screening of animal foods for presence of antibiotic residues. In this test local isolated culture of Bacillus subtilis was used as a test microorganism due to its high sensitivity to detect a wide range of antibiotics commonly used in animal disorders. The concentration of spore suspension of Bacillus subtilis JS2004 used in the formation of STAF plate was optimized at 2x107 spores/ ml. At this concentration, inhibition zone around Neomycin control disc was 10-16 mm. Nutrient agar was used as a medium in spore suspension and 0.4% dextrose was added as a constituent of medium. Zones of inhibition around swab samples and Neomycin control disc were observed and the diameter was measured. All swab samples showing a minimum of 2 mm wide inhibition zone around them were considered as positive for presence of antibiotic residues. The swab samples showing no zone of inhibition or a zone measuring less than 2 mm were considered as negative. Results of application of STAF test was on animal food samples revealed the high incidence of antibiotic residues.

Modelling the Effects of Surface Residual Stresses on Fatigue Behavior of PM Disk Alloys, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — A finite element based model will be developed and validated to capture the evolution of residual stresses and cold work at machined features of compressor and...

Solid residues

International Nuclear Information System (INIS)

Mulder, E.; Duin, P.J. van; Grootenboer, G.J.

1995-01-01

A summary is presented of the many investigations that have been done on solid residues of atmospheric fluid bed combustion (AFBC). These residues are bed ash, cyclone ash and bag filter ash. Physical and chemical properties are discussed and then the various uses of residues (in fillers, bricks, gravel, and for recovery of aluminium) are summarised. Toxicological properties of fly ash and stack ash are discussed as are risks of pneumoconiosis for workers handling fly ash, and contamination of water by ashes. On the basis of present information it is concluded that risks to public health from exposure to emissions of coal fly ash from AFBC appear small or negligible as are health risk to workers in the coal fly ash processing industry. 35 refs., 5 figs., 12 tabs

Chemical Control of Black Flies in Large Rivers as an Impact in Agrochemical Residue-Biota Interactions in Water Ecosystems

International Nuclear Information System (INIS)

Haufe, W.O.

1981-01-01

Livestock losses have been an obstacle to economic development of the farming and livestock industry in more northerly areas of Canada until two species of black fly, Simulium arcticum and S. luggeri, outbreaks are controlled effectively. The problem is complicated by its association with an abundance of large rivers and streams. Since effective control of black flies is presently limited to reduction of their breeding sources in flowing water, the managers of Canadian inland waters have been concerned about any major practice of using pesticides as black fly larvicides. Consequently, Canadian inland waters have been subject to continuous monitoring of major drainage systems with special attention to the chlorinated hydrocarbon insecticides. The latest status of residues was published from a Canadian Survey of 333 sampling locations between 1972 and 1975

Exposure of the Public from Large Deposits of Mineral Residues

International Nuclear Information System (INIS)

2011-06-01

All minerals and raw materials contain radionuclides of natural origin. In most situations, the exposure of humans to such radionuclides is considered to be part of the normal natural radiation background and is not generally of concern. In some cases, however, the radionuclide concentrations are elevated above normal levels or become elevated as a result of mineral processing activities, and measures for protecting against exposure to the material involved may need to be considered. The mineral or raw material is then treated as radioactive material for the purposes of radiation protection and falls within the definition of naturally occurring radioactive material (NORM). The IAEA has developed criteria for determining which materials need to be considered for regulatory control. For materials containing only radionuclides of natural origin, the criteria are an activity concentration of 1 Bq/g for 238 U, 235 U, 232 Th and their decay progeny and an activity concentration of 10 Bq/g for 40 K. These values were determined on the basis of the activity concentrations of these radionuclides in normal rocks and soil, and represent the (rounded) upper bounds of the ranges of such concentrations as determined by the United Nations Scientific Committee on the Effects of Atomic Radiation (UNSCEAR). The values are intended to apply to all solid materials except foodstuffs, material in transport and radioactive residues in the environment (for which separate criteria apply) and 40 K in the body (which is excluded entirely from regulatory requirements). While the radiation dose was not a consideration in the determination of the above-mentioned regulatory criteria, the IAEA has noted that doses received by individuals as a consequence of the use of these criteria are unlikely to exceed about 1 mSv in a year, excluding the emanation of radon. However, in the case of bulk volumes of material contaminating water pathways, such as large deposits of NORM residues from mining and

Vibration control for precision manufacturing at Sandia National Laboratories

International Nuclear Information System (INIS)

Hinnerichs, T.; Martinez, D.

1995-01-01

Sandia National Laboratories performs R and D in structural dynamics and vibration suppression for precision applications in weapon systems, space, underwater, transportation and civil structures. Over the last decade these efforts have expanded into the areas of active vibration control and ''smart'' structures and material systems. In addition, Sandia has focused major resources towards technology to support weapon product development and agile manufacturing capability for defense and industrial applications. This paper will briefly describe the structural dynamics modeling and verification process currently in place at Sandia that supports vibration control and some specific applications of these techniques to manufacturing in the areas of lithography, machine tools and flexible robotics

Vibration control for precision manufacturing at Sandia National Laboratories

Energy Technology Data Exchange (ETDEWEB)

Hinnerichs, T.; Martinez, D. [Sandia National Labs., Albuquerque, NM (United States). Structural Dynamics and Vibration Control Dept.

1995-04-01

Sandia National Laboratories performs R and D in structural dynamics and vibration suppression for precision applications in weapon systems, space, underwater, transportation and civil structures. Over the last decade these efforts have expanded into the areas of active vibration control and ``smart`` structures and material systems. In addition, Sandia has focused major resources towards technology to support weapon product development and agile manufacturing capability for defense and industrial applications. This paper will briefly describe the structural dynamics modeling and verification process currently in place at Sandia that supports vibration control and some specific applications of these techniques to manufacturing in the areas of lithography, machine tools and flexible robotics.

The advanced controls program at Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Knee, H.E.; White, J.D.

1990-01-01

The Oak Ridge National Laboratory (ORNL), under sponsorship of the US Department of Energy (DOE), is conducting research that will lead to advanced, automated control of new liquid-metal-reactor (LMR) nuclear power plants. Although this program of research (entitled the ''Advanced Controls Program'') is focused on LMR technology, it will be capable of providing control design, test, and qualification capability for other advanced reactor designs (e.g., the advanced light water reactor [ALWR] and high temperature gas-cooled reactor [HTGR] designs), while also benefiting existing nuclear plants. The Program will also have applicability to complex, non-nuclear process control environments (e.g., petrochemical, aerospace, etc.). The Advanced Controls Program will support capabilities throughout the entire plant design life cycle, i.e., from the initial interactive first-principle dynamic model development for the process, systems, components, and instruments through advanced control room qualification. The current program involves five principal areas of research activities: (1) demonstrations of advanced control system designs, (2) development of an advanced controls design environment, (3) development of advanced control strategies, (4) research and development (R ampersand D) in human-system integration for advanced control system designs, and (5) testing and validation of advanced control system designs. Discussion of the research in these five areas forms the basis of this paper. Also included is a description of the research directions of the program. 8 refs

Arroz tolerante a imidazolinonas: controle do arroz-vermelho, fluxo gênico e efeito residual do herbicida em culturas sucessoras não-tolerantes

OpenAIRE

Villa,S.C.C.; Marchezan,E.; Avila,L.A.; Massoni,P.F.S.; Telo,G.M.; Machado,S.L.O.; Camargo,E.R.

2006-01-01

Após várias décadas de busca de alternativas para controle do arroz-vermelho, desenvolveram-se genótipos de arroz tolerantes a herbicida do grupo químico das imidazolinonas, o qual controla eficientemente esta planta daninha no Sistema Clearfield. O experimento teve como objetivo avaliar: a eficiência do controle de arroz-vermelho com a mistura formulada dos herbicidas imazethapyr (75 g L-1) + imazapic (25 g L-1) (produto comercial Only®); o residual do herbicida no solo através dos danos cau...

Fuel gas production from animal and agricultural residues and biomass

Energy Technology Data Exchange (ETDEWEB)

Wise, D. L; Wentworth, R. L

1978-05-30

Progress was reported by all contractors. Topics presented include: solid waste to methane gas; pipeline fuel gas from an environmental cattle feed lot; heat treatment of organics for increasing anaerobic biodegradability; promoting faster anaerobic digestion; permselective membrane control of algae and wood digesters for increased production and chemicals recovery; anaerobic fermentation of agricultural residues; pilot plant demonstration of an anaerobic, fixed-film bioreactor for wastewater treatment; enhancement of methane production in the anaerobic diegestion of sewage; evaluation of agitation concepts for biogasification of sewage sludge; operation of a 50,000 gallon anaerobic digester; biological conversion of biomass to methane; dirt feedlot residue experiments; anaerobic fermentation of livestock and crop residues; current research on methanogenesis in Europe; and summary of EPA programs in digestion technology. (DC)

Overall and class-specific scores of pesticide residues from fruits and vegetables as a tool to rank intake of pesticide residues in United States: A validation study.

Science.gov (United States)

Hu, Yang; Chiu, Yu-Han; Hauser, Russ; Chavarro, Jorge; Sun, Qi

2016-01-01

Pesticide residues in fruits and vegetables are among the primary sources of pesticide exposure through diet, but the lack of adequate measurements hinder the research on health effects of pesticide residues. Pesticide Residue Burden Score (PRBS) for estimating overall dietary pesticide intake, organochlorine pesticide score (OC-PRBS) and organophosphate pesticide score (OP-PRBS) for estimating organochlorine and organophosphate pesticides-specific intake, respectively, were derived using U.S. Department of Agriculture Pesticide Data Program data and National Health and Nutrition Examination Survey (NHANES) food frequency questionnaire data. We evaluated the performance of these scores by validating the scores against pesticide metabolites measured in urine or serum among 3,679 participants in NHANES using generalized linear regression. The PRBS was positively associated with a score summarizing the ranks of all pesticide metabolites in a linear fashion (p for linear trend trend trend 0.07) for the OC-PRBS. The PRBS and OP-PRBS had similar performance when they were derived from fruits and vegetables with high vs. low pesticide residues, respectively (p for trend trend 0.07) than from less contaminated Fruits and vegetables (p for trend 0.63), although neither of the associations achieved statistical significance. The PRBS and the class-specific scores for two major types of pesticides were significantly associated with pesticide biomarkers. These scores can reasonably rank study participants by their pesticide residue exposures from fruits and vegetables in large-scale environmental epidemiological studies. Copyright © 2016 Elsevier Ltd. All rights reserved.

Establishment of 2000 National Geodetic Control Network of China and It’s Technological Progress

Directory of Open Access Journals (Sweden)

CHEN Junyong

2007-02-01

Full Text Available Objectives: 2000’ National Geodetic Control Network of China is an important fundamental scientific engineering project in China. It consists of three parts which are establishment of 2000 National GPS Geodetic Network, its combination adjustment with national astro-geodetic network and 2000 National Gravity Fundamental network. It provides the high precise coordinate reference and gravity reference for three dimensional geo-center national coordinates system and gravity system, respectively. Additionally, it provides precise unified geometric and physical geodesy information for the economic construction, the national defense and the scientific research. Methods: 1. The larger number of data are processed in triple networks adjustment of 2000 National GPS Geodetic Network, which are chosen from the GPS monitoring stations, such as grade A, B of national GPS network , grade 1st and 2nd of national GPS network, crustal movement observation network of China, and others crustal deformation monitoring stations. Finally, the data of 2666 GPS stations are used in the data processing of 2000 National GPS Geodetic Network, including 124 external stations and 2542 internal stations. In order to the results of triple networks adjustment are corresponding to that of three dimensional geo-center coordinates system, ITRF 97 and epoch 2000.0 are chosen as the coordinate reference frame and epoch reference, respectively. The methods of “strong reference” and “weak reference” are combined used in the control data selection of triple networks adjustment. The scale and rotation scales are adopted for each sub network. The least square adjustment is firstly adopted in each sub network adjustment. The data of obvious abnormal baselines are found and rejected firstly. And the method of double factor robust estimation is adopted in the data processing. 2. The combined adjustment of 2000 National GPS Geodetic Network and national astro-geodetic network is

Thermal inertializing of solid incinerator residues

International Nuclear Information System (INIS)

Proelss, J.

2003-01-01

Inertialization of residues is a key task of incinerators. Residues of conventional incineration processes may contain high levels of inorganic or organic pollutants and must be treated prior to recycling. the most effective process is thermal treatment above the melting point. This will destroy organic pollutants like dioxins/furans and pathogenic compounds, while the heavy metals will be partly volatilized. The glassy slag obtained as end product is low in heavy metals and more or less resistant to leaching. The The author describes a method for calculating activity coefficients of volatile components of diluted, liquid multicomponent systems. With these data, the data base for thermodynamic description of fluid mixtures was updated, and a set of characteristic data was established for describing transport in an inflatable module. Once the activity coefficients of interesting constituents of the slag are known along with the transport conditions in the volatilization process, it is possible to optimize the thermal treatment of critical ashes and dusts with a view to energy consumption and process control. In two different exemplary process concepts, the energy consumption for residue treatment is estimated. The processes proposed are compared with published process proposals, and their energy consumption is assessed in a comoparative study [de

Viscoelastic finite element analysis of residual stresses in porcelain-veneered zirconia dental crowns.

Science.gov (United States)

Kim, Jeongho; Dhital, Sukirti; Zhivago, Paul; Kaizer, Marina R; Zhang, Yu

2018-06-01

The main problem of porcelain-veneered zirconia (PVZ) dental restorations is chipping and delamination of veneering porcelain owing to the development of deleterious residual stresses during the cooling phase of veneer firing. The aim of this study is to elucidate the effects of cooling rate, thermal contraction coefficient and elastic modulus on residual stresses developed in PVZ dental crowns using viscoelastic finite element methods (VFEM). A three-dimensional VFEM model has been developed to predict residual stresses in PVZ structures using ABAQUS finite element software and user subroutines. First, the newly established model was validated with experimentally measured residual stress profiles using Vickers indentation on flat PVZ specimens. An excellent agreement between the model prediction and experimental data was found. Then, the model was used to predict residual stresses in more complex anatomically-correct crown systems. Two PVZ crown systems with different thermal contraction coefficients and porcelain moduli were studied: VM9/Y-TZP and LAVA/Y-TZP. A sequential dual-step finite element analysis was performed: heat transfer analysis and viscoelastic stress analysis. Controlled and bench convection cooling rates were simulated by applying different convective heat transfer coefficients 1.7E-5 W/mm 2 °C (controlled cooling) and 0.6E-4 W/mm 2 °C (bench cooling) on the crown surfaces exposed to the air. Rigorous viscoelastic finite element analysis revealed that controlled cooling results in lower maximum stresses in both veneer and core layers for the two PVZ systems relative to bench cooling. Better compatibility of thermal contraction coefficients between porcelain and zirconia and a lower porcelain modulus reduce residual stresses in both layers. Copyright © 2018 Elsevier Ltd. All rights reserved.

Thermally induced transformations of iron oxide stabilised APC residues from waste incineration

DEFF Research Database (Denmark)

Sørensen, Mette Abildgaard; Koch, C.B.

2001-01-01

Air pollution control (APC) facilities at waste incinerator plants produce large quantities of solid residues rich in salts and heavy metals. Heavy metals are readily released to water from the residues and it has, therefore, been found suitable to apply a rapid co-precipitation/adsorption process...... as a means to immobilize the toxic elements. In the 'Ferrox process', this immobilization is based on co-precipitation with an Fe(III) oxide formed by oxidation of Fe(II) by air in an aqueous slurry with the APC residue at alkaline pH. In this work we have undertaken a Mossbauer spectroscopy study of the Fe...

Handling of Solid Residues

International Nuclear Information System (INIS)

Medina Bermudez, Clara Ines

1999-01-01

The topic of solid residues is specifically of great interest and concern for the authorities, institutions and community that identify in them a true threat against the human health and the atmosphere in the related with the aesthetic deterioration of the urban centers and of the natural landscape; in the proliferation of vectorial transmitters of illnesses and the effect on the biodiversity. Inside the wide spectrum of topics that they keep relationship with the environmental protection, the inadequate handling of solid residues and residues dangerous squatter an important line in the definition of political and practical environmentally sustainable. The industrial development and the population's growth have originated a continuous increase in the production of solid residues; of equal it forms, their composition day after day is more heterogeneous. The base for the good handling includes the appropriate intervention of the different stages of an integral administration of residues, which include the separation in the source, the gathering, the handling, the use, treatment, final disposition and the institutional organization of the administration. The topic of the dangerous residues generates more expectation. These residues understand from those of pathogen type that are generated in the establishments of health that of hospital attention, until those of combustible, inflammable type, explosive, radio-active, volatile, corrosive, reagent or toxic, associated to numerous industrial processes, common in our countries in development

Workshop on agricultural and agro-industrial residue utilization in the ESCAP region

Energy Technology Data Exchange (ETDEWEB)

Vimal, O P

1980-02-01

A summary of the workshop held at Pattaya, Thailand is given at which the present status of both technological and non-technical aspects of utilization of agricultural and industrial residues in the ESCAP region are reviewed. A course of action was recommended whereby national programmes could develop and international assistance be focussed through follow up activities.

Good performances but short lasting efficacy of Actellic 50 EC Indoor Residual Spraying (IRS) on malaria transmission in Benin, West Africa.

Science.gov (United States)

Aïkpon, Rock; Sèzonlin, Michel; Tokponon, Filémon; Okè, Mariam; Oussou, Olivier; Oké-Agbo, Frédéric; Beach, Raymond; Akogbéto, Martin

2014-05-30

The National Malaria Control Program (NMCP) has been using pirimiphos methyl for the first time for indoor residual spraying (IRS) in Benin. The first round was a success with a significant decrease of entomological indicators of malaria transmission in the treated districts. We present the results of the entomological impact on malaria transmission. Entomologic parameters in the control area were compared with those in intervention sites. Mosquito collections were carried out in three districts in the Atacora-Dongo region of which two were treated with pirimiphos methyl (Actellic 50EC) (Tanguiéta and Kouandé) and the untreated (Copargo) served as control. Anopheles gambiae s.l. populations were sampled monthly by human landing catch. In addition, window exit traps and pyrethrum spray catches were performed to assess exophagic behavior of Anopheles vectors. In the three districts, mosquito collections were organized to follow the impact of pirimiphos methyl IRS on malaria transmission and possible changes in the behavior of mosquitoes. The residual activity of pirimiphos methyl in the treated walls was also assessed using WHO bioassay test. A significant reduction (94.25%) in human biting rate was recorded in treated districts where an inhabitant received less than 1 bite of An. gambiae per night. During this same time, the entomological inoculation rate (EIR) dramatically declined in the treated area (99.24% reduction). We also noted a significant reduction in longevity of the vectors and an increase in exophily induced by pirimiphos methyl on An. gambiae. However, no significant impact was found on the blood feeding rate. Otherwise, the low residual activity of Actellic 50 EC, which is three months, is a disadvantage. Pirimiphos methyl was found to be effective for IRS in Benin. However, because of the low persistence of Actellic 50EC used in this study on the treated walls, the recourse to another more residual formulation of pirimiphos methyl is required.

Assessment of long-term pH developments in leachate from waste incineration residues

DEFF Research Database (Denmark)

Astrup, Thomas; Jakobsen, Rasmus; Christensen, Thomas Højlund

2006-01-01

influenced by changes in pH over time. The paper presents an approach for assessing pH changes in leachate from municipal solid waste incineration (MSWI) air-pollution-control (APC) residues. Residue samples were subjected to a stepwise batch extraction method in order to obtain residue samples at a range...... of pH Values (similar to common pH-dependence tests), and then on these samples to determine leaching of alkalinity as well as remaining solid phase alkalinity. On a range of APC residues covering various pretreatment and disposal options, this procedure was used to determine leachable and residual...... alkalinity as a function of pH. Mass balance calculations for typical disposal scenarios were used to provide data on pH as a function of the liquid-to-solid (L/S) ratio in the leaching system. Regardless of residue type and pretreatment, pH was found to stay above 7 for L/S ratios up to about 2000 L kg(-1...

Effects of processing treatment on pesticide residues in fruits and their products

International Nuclear Information System (INIS)

Mao Xuefei; Jiao Bining; Fu Chenmei; Qian Yongzhong; Wang Jing

2008-01-01

The influence of processing treatments on pesticide residues in fruits and their products was reviewed. The effects on pesticide residues and relative control treatments for each processing step, including peeling, washing, sterilization, juicing, clarification, filtration, drying and fermentation, were discussed, respectively. Meanwhile we analyzed the future development prospectin of this field, in order to provide some suggestions for commercial fruit industry and consumers' health. (authors)

Concentration-Response and Residual Activity of Insecticides to Control Herpetogramma phaeopteralis (Lepidoptera: Crambidae) in St. Augustinegrass.

Science.gov (United States)

Tofangsazi, Nastaran; Cherry, Ron H; Beeson, Richard C; Arthurs, Steven P

2015-04-01

Tropical sod webworm, Herpetogramma phaeopteralis Guenée, is an important pest of warm-season turfgrass in the Gulf Coast states of the United States, the Caribbean Islands, and Central America. Current control recommendations rely on topical application of insecticides against caterpillars. The objective of this study was to generate resistance baseline data of H. phaeopteralis to six insecticide classes. Residual activity of clothianidin, chlorantraniliprole, and bifenthrin was also compared under field conditions in Central Florida. Chlorantraniliprole was the most toxic compound tested (LC50 value of 4.5 ppm), followed by acephate (8.6 ppm), spinosad (31.1 ppm), clothianidin (46.6 ppm), bifenthrin (283 ppm) and Bacillus thuringiensis kurstaki, (342 ppm). In field tests, all compounds at label rates were effective (≥94% mortality of larvae exposed to fresh residues). However, a more rapid decline in activity of clothianidin and bifenthrin was observed compared with chlorantraniliprole. Clothianidin had no statistically detectable activity after 4 wk post-application in spring and the fall, and bifenthrin had no detectable activity after 3 wk in the spring and the fall. However, chlorantraniliprole maintained significant activity (≥84% mortality) compared with other treatments throughout the 5-wk study period. This study provides new information regarding the relative toxicities and persistence of current insecticides used for H. phaeopteralis and other turfgrass caterpillars. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Gynecologic Cancer Prevention and Control in the National Comprehensive Cancer Control Program: Progress, Current Activities, and Future Directions

OpenAIRE

Stewart, Sherri L.; Lakhani, Naheed; Brown, Phaeydra M.; Larkin, O. Ann; Moore, Angela R.; Hayes, Nikki S.

2013-01-01

Gynecologic cancer confers a large burden among women in the United States. Several evidence-based interventions are available to reduce the incidence, morbidity, and mortality from these cancers. The National Comprehensive Cancer Control Program (NCCCP) is uniquely positioned to implement these interventions in the US population. This review discusses progress and future directions for the NCCCP in preventing and controlling gynecologic cancer.

Gynecologic cancer prevention and control in the National Comprehensive Cancer Control Program: progress, current activities, and future directions.

Science.gov (United States)

Stewart, Sherri L; Lakhani, Naheed; Brown, Phaeydra M; Larkin, O Ann; Moore, Angela R; Hayes, Nikki S

2013-08-01

Gynecologic cancer confers a large burden among women in the United States. Several evidence-based interventions are available to reduce the incidence, morbidity, and mortality from these cancers. The National Comprehensive Cancer Control Program (NCCCP) is uniquely positioned to implement these interventions in the US population. This review discusses progress and future directions for the NCCCP in preventing and controlling gynecologic cancer.

Measurement of residual stress in quenched 1045 steel by the nanoindentation method

International Nuclear Information System (INIS)

Zhu Lina; Xu Binshi; Wang Haidou; Wang Chengbiao

2010-01-01

In this paper, the residual stress in quenched AISI 1045 steel was measured by a recently developed nanoindentation technique. Depth control mode was adopted to measure the residual stress. It was found that residual compressive stress was generated in the quenched steel. The material around nanoindents exhibits significant pile-up deformation. A new method was proposed to determine the real contact area for pile-up material on the basis of invariant pile-up morphology of the loaded or unloaded states. The results obtained by the new method were in good agreement with the residual stresses measured by the classical X-ray diffraction (XRD) method. - Research Highlights: → A new method was proposed to measure the real contact area for pile-up materials. → The real contact depth is defined as the sum of h max and the pile-up height h p . → The value of residual stress measured by the nanoindentation method was in good agreement with that by the XRD method.

National Case-Control Study of Homicide Offending and Methamphetamine Use

Science.gov (United States)

Stretesky, Paul B.

2009-01-01

The purpose of this study is to examine the relationship between methamphetamine use and homicide. To carry out this study, data from the National Household Survey on Drug Abuse and Survey of Inmates in State and Federal Correctional Facilities were combined to create a case-control design. The main exposure measure is methamphetamine use and the…

Encouraging tobacco control using national multisectoral ministerial mandate and priorities in Indonesia

Directory of Open Access Journals (Sweden)

Farrukh Qureshi

2018-03-01

In countries having strong tobacco industry influence, tobacco control issue needs to be brought forward within larger policy mandates of non-health sector ministries, using their national priorities. Intergovernmental organizations as well as other partners and organizations working on tobacco control should expand reach out to sectors beyond health, establish and encourage dialogue; and help develop ownership of these sectors on specific policy interventions that directly or indirectly support implementation of key policy measures for tobacco control.

Repeat Brachytherapy for Patients With Residual or Recurrent Tumors of Oral Cavity

Energy Technology Data Exchange (ETDEWEB)

Yoshimura, Ryo-ichi, E-mail: ysmrmrad@tmd.ac.jp [Department of Diagnostic Radiology and Oncology, Tokyo Medical and Dental University, Tokyo (Japan); Shibuya, Hitoshi; Hayashi, Keiji; Nakagawa, Keiko; Toda, Kazuma [Department of Diagnostic Radiology and Oncology, Tokyo Medical and Dental University, Tokyo (Japan); Watanabe, Hiroshi [Department of Oral and Maxillofacial Radiology, Tokyo Medical and Dental University, Tokyo (Japan); Kaida, Atushi; Miura, Masahiko [Department of Oral Radiation Oncology, Tokyo Medical and Dental University, Tokyo (Japan)

2012-07-15

Purpose: To analyze data from patients receiving repeat brachytherapy (re-BT) for the treatment of residual or recurrent tumor in the oral cavity. Methods and Materials: Between January 2003 and December 2007, 62 patients who had undergone definitive BT as an initial treatment of oral cancer subsequently underwent re-BT for the treatment of residual or recurrent tumors at the diagnostic radiology and oncology department (Tokyo Medical and Dental University Hospital). Re-BT was performed 0.9-73 months (median, 5.7) after the initial BT. Au-198 grains were used as the re-BT source in all 62 patients, and an area of 0.8-6.3 cm{sup 2} (median, 3.1) was permanently irradiated with 60-110 Gy (median, 83) according to the system of Paterson-Parker. Results: The 2-year local control and overall survival rate was 53% and 66%, respectively, and local control significantly affected overall survival. Both local control and overall survival were affected by the initial tumor characteristics and the macroscopic appearance of the residual or recurrent tumor. Grade 3 or 4 complications were seen in 5 patients. The incidence of mandibular and mucosal complications was significantly related to a biologic effective dose of {alpha}/{beta} of 3 Gy to the surface of the gingiva and mucosa, respectively. Conclusion: Re-BT using Au-198 grains for the treatment of residual or recurrent tumor after definitive BT in the oral cavity is effective and well tolerated.

Anaerobia Treatments of the domestic residual waters. Limitations potentialities

International Nuclear Information System (INIS)

Giraldo Gomez, Eugenio

1993-01-01

The quick growth of the Latin American cities has prevented that an appropriate covering of public services is achieved for the whole population, One of the undesirable consequences of this situation is the indiscriminate discharge from the domestic and industrial residual waters to the nearest bodies of water with its consequent deterioration and with disastrous consequences about the ecology and the public health. The developed countries have controlled this situation using systems of purification of the residual waters previously to their discharge in the receptor source. The same as the technology of the evacuation of the served waters, they have become numerous efforts for the application of the purification systems used in the countries developed to the socioeconomic, climatic and cultural conditions of our means. One of the results obtained in these efforts is the economic inability of the municipalities to pay the high investment costs and of operation of the traditional systems for the treatment of the residual waters. Contrary to another type of public services, the treatment of the residual waters needs of appropriate technological solutions for the Climatic and socioeconomic means of the developing countries, One of the technological alternatives for the purification of the residual waters that has had a great development in the last decades has been that of the biological treatments in t anaerobia ambient. The objective of this contribution is to present, to author's trial, the limitations and potentialities of this technology type with special emphasis in the case of the domestic residual waters

Establishment and development of the National Tuberculosis Control Programme in Vietnam

NARCIS (Netherlands)

Huong, N. T.; Duong, B. D.; Co, N. V.; Quy, H. T.; Tung, L. B.; Bosman, M.; Gebhardt, A.; Velema, J. P.; Broekmans, J. F.; Borgdorff, M. W.

2005-01-01

OBJECTIVE: To describe the establishment and development of the National Tuberculosis Control Programme (NTP) of Vietnam. METHODS: Data were obtained from the surveillance system established by the new NTP in 1986 and based on the principles now described as the WHO DOTS strategy. RESULTS: The

Knowledge and perceptions about indoor residual spray for malaria ...

African Journals Online (AJOL)

Background: Malaria control and intervention tools usage and coverage in community depend on community acceptability and compliance. Indoor residual spray (IRS) and long lasting insecticide treated nets (LLINs) are the preferred and recommended intervention tools. This study assessed the knowledge and perceptions ...

PENETAPAN RESIDU DAN PERKIRAAN PENETAPAN BATAS MAKSIMUM RESIDU (BMR ORGANOKLORIN PADA SIMPLISIA

Directory of Open Access Journals (Sweden)

Ani Isnawati

2012-10-01

Full Text Available Penggunaaan bahan obat tradisional (simplisia untuk skala industri dan peningkatan produksi tanaman obat dalam skala besar menjadi tidak ekonomis tanpa pestisida. Disatu sisi penggunaan pestisida dapat menguntungkan yaitu menyebabkan toksis pada hama namun disisi lain toksisitas dapat terjadi juga pada manusia, sehingga residu pestisida dalam tanaman obat yang dikonsumsi dalam jangka panjang akan merugikan kesehatan. Batas maksimum Residu (BMR pestisida dalam simplisia baik di Indonesia maupun di negara lain belum ditetapkan. Sehingga untuk itu untuk mengetahui adanya residu pestisida jenis organoklorin yang telah dilarang penggunaannya melalui Permentan No.434.1/kpts/TP.270/7/2001 dan untuk mengetahui batas keamanannya, maka perlu dilakukan penetapan residu organoklorin dalam simplisia dan menetapkan batas keamanan berdasarkan perhitungan secara teoritis. Pengujian residu dilakukan terhadap golongan pestisida organoklorin pada 4 jenis simplisia (daun wungu (Graptophyllum pictum (L Grifl, daun sambiloto Andrographis paniculata Ness, herba pegagan (Centella  asiatica (L Urban, daun tempuyung (Sonchus arvensis (L yang berasal dari 3 lokasi penanaman, yaitu : perkebunan Tanaman Obat Manako (Jawa Barat, Balai Penelitian Tanaman Obat Tawangmangu (BPTO di Jawa Tengah dan Perkebunan Tanaman Obat Purwodadi (Jawa Timur. Pemeriksaan residu pestisida organoklorin menggunakan kromatografi gas dan perhitungan batas keamanan dihitung dengan adanya nilai ADI (Acceptable daily intake yang telah ditetapkan bersama antara JAO dan WHO serta perkiraan banyaknya konsumsi simplisia. Hasil Pengujian residu pestisida organoklorin diperoleh bahwa simplisia daun Wungu (Tawangmangu mengandung residu lindan dengan kadar 0,24 mg/kg, pegagan (Purwodadi, mengandung lindan 0,36 mg/kg dan aldrin 0,31 mg/kg serta pegagan (Manako mengandung heptaklor 0,15 mg/kg dan op-DDE 0,11 mg/kg. Adapun penghitungan BMR heptaklor dan lindan secara teoritis dengan asumsi rata

Standard Test Method for Gravimetric Determination of Nonvolatile Residue (NVR) in Environmentally Controlled Areas for Spacecraft

CERN Document Server

American Society for Testing and Materials. Philadelphia

2008-01-01

1.1 This test method covers the determination of nonvolatile residue (NVR) fallout in environmentally controlled areas used for the assembly, testing, and processing of spacecraft. 1.2 The NVR of interest is that which is deposited on sampling plate surfaces at room temperature: it is left to the user to infer the relationship between the NVR found on the sampling plate surface and that found on any other surfaces. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

Residual magnetic field in rotary machines; Campo magnetico residual en maquinas rotatorias

Energy Technology Data Exchange (ETDEWEB)

Gonzalez V, Esteban A; Apanco R, Marcelino [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2007-07-01

The residual magnetism is a phenomenon in which the magnetic dipoles of a substance are oriented in a certain degree. On the other hand, when internal forces exist capable of aligning elementary magnetic dipoles of a material, a permanent magnet is obtained. Just as in a conductor or in a material, in the elements of a rotary electrical machine magnetic fields can be induced that produce a residual magnetism or magnetization. In the rotary electrical machines, the magnetization phenomenon causes serious problems, such as the generation of induced currents that propitiate the mechanical wear in bearings, collars, trunnions and inclusive in the shaft, by effects known as pitting, frosting and spark tracks, as well as erroneous readings in vibration and temperature sensors, that in some cases can cause the shut down of the machine. In this article are presented the general concepts on the residual magnetism in rotary electrical machines, the causes that originate it and the problems that arises, as well as the demagnetization of the components that have residual magnetic field. The results obtained by the area of Electrical Equipment of the Instituto de Investigaciones Electricas are revised, during the execution of activities related to the measurement and elimination of the residual magnetic field in rotary electrical machines. [Spanish] El magnetismo residual es un fenomeno en el que los dipolos magneticos de una sustancia se encuentran orientados en un grado determinado. Por otro lado, cuando existen fuerzas internas capaces de alinear los dipolos magneticos elementales de un material, se tiene un iman permanente. Al igual que en un conductor o un material, en los elementos de una maquina electrica rotatoria se pueden inducir campos magneticos que producen un magnetismo residual o magnetizacion. En las maquinas electricas rotatorias, el fenomeno de magnetizacion causa graves problemas, como la generacion de corrientes inducidas que propician el desgaste mecanico

Computer Simulations Reveal Multiple Functions for Aromatic Residues in Cellulase Enzymes (Fact Sheet)

Energy Technology Data Exchange (ETDEWEB)

2012-07-01

NREL researchers use high-performance computing to demonstrate fundamental roles of aromatic residues in cellulase enzyme tunnels. National Renewable Energy Laboratory (NREL) computer simulations of a key industrial enzyme, the Trichoderma reesei Family 6 cellulase (Cel6A), predict that aromatic residues near the enzyme's active site and at the entrance and exit tunnel perform different functions in substrate binding and catalysis, depending on their location in the enzyme. These results suggest that nature employs aromatic-carbohydrate interactions with a wide variety of binding affinities for diverse functions. Outcomes also suggest that protein engineering strategies in which mutations are made around the binding sites may require tailoring specific to the enzyme family. Cellulase enzymes ubiquitously exhibit tunnels or clefts lined with aromatic residues for processing carbohydrate polymers to monomers, but the molecular-level role of these aromatic residues remains unknown. In silico mutation of the aromatic residues near the catalytic site of Cel6A has little impact on the binding affinity, but simulation suggests that these residues play a major role in the glucopyranose ring distortion necessary for cleaving glycosidic bonds to produce fermentable sugars. Removal of aromatic residues at the entrance and exit of the cellulase tunnel, however, dramatically impacts the binding affinity. This suggests that these residues play a role in acquiring cellulose chains from the cellulose crystal and stabilizing the reaction product, respectively. These results illustrate that the role of aromatic-carbohydrate interactions varies dramatically depending on the position in the enzyme tunnel. As aromatic-carbohydrate interactions are present in all carbohydrate-active enzymes, the results have implications for understanding protein structure-function relationships in carbohydrate metabolism and recognition, carbon turnover in nature, and protein engineering

Non-Destructive Measurement of Residual Strain in Connecting Rods Using Neutrons

Energy Technology Data Exchange (ETDEWEB)

Ikeda, Tomohiro [Honda R& D; Bunn, Jeffrey R. [ORNL; Fancher, Christopher M. [ORNL; Seid, Alan [Honda R& D; Motani, Ryuta [Honda R& D; Matsuda, Hideki [Honda R& D; Okayama, Tatsuya [Honda R& D

2018-04-01

Increasing the strength of materials is effective in reducing weight and boosting structural part performance, but there are cases in where the residual strain generated during the process of manufacturing of high-strength materials results in a decline of durability. It is therefore important to understand how the residual strain in a manufactured component changes due to processing conditions. In the case of a connecting rod, because the strain load on the connecting rod rib sections is high, it is necessary to clearly understand the distribution of strain in the ribs. However, because residual strain is generally measured by using X-ray diffractometers or strain gauges, measurements are limited to the surface layer of the parts. Neutron beams, however, have a higher penetration depth than X-rays, allowing for strain measurement in the bulk material. The research discussed within this paper consists of non-destructive residual strain measurements in the interior of connecting rods using the 2nd Generation Neutron Residual Stress Mapping Facility (NRSF2) at Oak Ridge National Laboratory, measuring the Fe (211) diffraction peak position of the ferrite phase. The interior strain distribution of connecting rod, which prepared under different manufacturing processes, was revealed. By the visualization of interior strains, clear understandings of differences in various processing conditions were obtained. In addition, it is known that the peak width, which is also obtained during measurement, is suggestive of the size of crystallites in the structure; however the peak width can additionally be caused by microstresses and material dislocations.

Role of grain boundary nature and residual strain in controlling sensitisation of type 304 stainless steel

International Nuclear Information System (INIS)

Ahmedabadi, Parag M.; Kain, Vivekanand; Dangi, Bhupinder Kumar; Samajdar, I.

2013-01-01

Highlights: ► Low-level of residual strain improved resistance to sensitisation. ► High fraction of special boundaries did not always reduce sensitisation. ► Area attacked during the EPR test correlated well with degree of sensitisation. ► Volume loss during the EPR test also correlated well with degree of sensitisation. - Abstract: The effects of residual strain and grain boundary character distribution on sensitisation of type 304 stainless steel at 525 °C were evaluated using electrochemical potentiokinetic reactivation (EPR) technique. The results indicated that a very low level of residual strain and a high fraction of annealing twins significantly improved the resistance to sensitisation. Image analysis indicated that the fraction of area attacked during the EPR test correlated well with the EPR data. The volume loss, calculated using atomic force microscopic examinations, during the EPR tests also correlated well with the EPR results.

Entropy Transfer between Residue Pairs and Allostery in Proteins: Quantifying Allosteric Communication in Ubiquitin.

Directory of Open Access Journals (Sweden)

Aysima Hacisuleyman

2017-01-01

Full Text Available It has recently been proposed by Gunasakaran et al. that allostery may be an intrinsic property of all proteins. Here, we develop a computational method that can determine and quantify allosteric activity in any given protein. Based on Schreiber's transfer entropy formulation, our approach leads to an information transfer landscape for the protein that shows the presence of entropy sinks and sources and explains how pairs of residues communicate with each other using entropy transfer. The model can identify the residues that drive the fluctuations of others. We apply the model to Ubiquitin, whose allosteric activity has not been emphasized until recently, and show that there are indeed systematic pathways of entropy and information transfer between residues that correlate well with the activities of the protein. We use 600 nanosecond molecular dynamics trajectories for Ubiquitin and its complex with human polymerase iota and evaluate entropy transfer between all pairs of residues of Ubiquitin and quantify the binding susceptibility changes upon complex formation. We explain the complex formation propensities of Ubiquitin in terms of entropy transfer. Important residues taking part in allosteric communication in Ubiquitin predicted by our approach are in agreement with results of NMR relaxation dispersion experiments. Finally, we show that time delayed correlation of fluctuations of two interacting residues possesses an intrinsic causality that tells which residue controls the interaction and which one is controlled. Our work shows that time delayed correlations, entropy transfer and causality are the required new concepts for explaining allosteric communication in proteins.

Entropy Transfer between Residue Pairs and Allostery in Proteins: Quantifying Allosteric Communication in Ubiquitin.

Science.gov (United States)

Hacisuleyman, Aysima; Erman, Burak

2017-01-01

It has recently been proposed by Gunasakaran et al. that allostery may be an intrinsic property of all proteins. Here, we develop a computational method that can determine and quantify allosteric activity in any given protein. Based on Schreiber's transfer entropy formulation, our approach leads to an information transfer landscape for the protein that shows the presence of entropy sinks and sources and explains how pairs of residues communicate with each other using entropy transfer. The model can identify the residues that drive the fluctuations of others. We apply the model to Ubiquitin, whose allosteric activity has not been emphasized until recently, and show that there are indeed systematic pathways of entropy and information transfer between residues that correlate well with the activities of the protein. We use 600 nanosecond molecular dynamics trajectories for Ubiquitin and its complex with human polymerase iota and evaluate entropy transfer between all pairs of residues of Ubiquitin and quantify the binding susceptibility changes upon complex formation. We explain the complex formation propensities of Ubiquitin in terms of entropy transfer. Important residues taking part in allosteric communication in Ubiquitin predicted by our approach are in agreement with results of NMR relaxation dispersion experiments. Finally, we show that time delayed correlation of fluctuations of two interacting residues possesses an intrinsic causality that tells which residue controls the interaction and which one is controlled. Our work shows that time delayed correlations, entropy transfer and causality are the required new concepts for explaining allosteric communication in proteins.

Sliding Mode Control of a Slewing Flexible Beam

Science.gov (United States)

Wilson, David G.; Parker, Gordon G.; Starr, Gregory P.; Robinett, Rush D., III

1997-01-01

An output feedback sliding mode controller (SMC) is proposed to minimize the effects of vibrations of slewing flexible manipulators. A spline trajectory is used to generate ideal position and velocity commands. Constrained nonlinear optimization techniques are used to both calibrate nonlinear models and determine optimized gains to produce a rest-to-rest, residual vibration-free maneuver. Vibration-free maneuvers are important for current and future NASA space missions. This study required the development of the nonlinear dynamic system equations of motion; robust control law design; numerical implementation; system identification; and verification using the Sandia National Laboratories flexible robot testbed. Results are shown for a slewing flexible beam.

Health, social and economic consequences of hypersomnia: a controlled national study from a national registry evaluating the societal effect on patients and their partners.

Science.gov (United States)

Jennum, Poul; Ibsen, Rikke; Avlund, Kirsten; Kjellberg, Jakob

2014-04-01

Hypersomnia causes significant socioeconomic burden, but there is insufficient information about the time course and the effect on the partner. The aim of this study was to estimate the factual direct and productivity costs of hypersomnia in a controlled study including all national patients and their partners. Using records from the Danish National Patient Registry (1997-2009), we identified all patients with a diagnosis of hypersomnia and compared these patients and their partners with randomly chosen controls matched for age, gender, geographic area and marital status. Direct and productivity costs, including frequencies of primary and sector contacts and procedures, medication, labour supply and social transfer payments were extracted from the national databases. A total of 2,855 national patients was compared to 11,382 controls. About 70 % of patients and controls were married or cohabiting. Patients with hypersomnia had significantly higher rates of health-related contact, medication use and socioeconomic cost. Furthermore, they had slightly lower employment rates, and those in employment had a lower income level than control subjects. The annual mean excess health-related cost including social transfers was 3,498 for patients with hypersomnia and 3,851 for their partners. The social and health-related consequences could be identified up to 11 years before the first diagnosis among both the patients and their partners and became more pronounced as the disease advanced. The health effects were present in all age groups and in both genders. On the basis of this retrospective controlled study in the Danish population, symptoms and findings of hypersomnia are associated with major socioeconomic consequences for patients, their partners and society.

Characterization Report on Sand, Slag, and Crucible Residues and on Fluoride Residues

International Nuclear Information System (INIS)

Murray, A.M.

1999-01-01

This paper reports on the chemical characterization of the sand, slag, and crucible (SS and C) residues and the fluoride residues that may be shipped from the Rocky Flats Environmental Technology Site (RFETS) to Savannah River Site (SRS)

Interfacing solvent extraction in the recovery of pyrochemical residues at the Savannah River Plant

International Nuclear Information System (INIS)

Gray, L.W.; Holcomb, H.P.

1986-01-01

The traditional feedstock for plutonium recovery at the Savannah River Plant (SRP) has been spent reactor fuel elements and irradiated targets. Feed sources have included both onsite reactors and a wide variety of domestic and foreign reactors. For the past few years, a growing and increasingly varied mix of unirradiated plutonium residues has been purified through SRP aqueous-based processes. Recently, plutonium residues generated in various chloride salt melts have become a significant offsite source of feed for SRP recovery operations. Impure plutonium metal and plutonium alloys have also been processed. A broader range of molten salt and other high temperature residues is anticipated for the future. The major advantage of solvent extraction for scrap purification is the versatility of the solvent extraction system which allows numerous contaminants to be removed by routine operations. Major concerns are nuclear safety control, corrosion of equipment, and control of releases to the environment. SRP's past, present, and future interfacing of solvent extraction in processing pyrochemical and other plutonium-containing residues is reviewed

Residual stress by repair welds

International Nuclear Information System (INIS)

Mochizuki, Masahito; Toyoda, Masao

2003-01-01

Residual stress by repair welds is computed using the thermal elastic-plastic analysis with phase-transformation effect. Coupling phenomena of temperature, microstructure, and stress-strain fields are simulated in the finite-element analysis. Weld bond of a plate butt-welded joint is gouged and then deposited by weld metal in repair process. Heat source is synchronously moved with the deposition of the finite-element as the weld deposition. Microstructure is considered by using CCT diagram and the transformation behavior in the repair weld is also simulated. The effects of initial stress, heat input, and weld length on residual stress distribution are studied from the organic results of numerical analysis. Initial residual stress before repair weld has no influence on the residual stress after repair treatment near weld metal, because the initial stress near weld metal releases due to high temperature of repair weld and then stress by repair weld regenerates. Heat input has an effect for residual stress distribution, for not its magnitude but distribution zone. Weld length should be considered reducing the magnitude of residual stress in the edge of weld bead; short bead induces high tensile residual stress. (author)

ESTIMATION OF THE BURDEN OF PESTICIDE RESIDUES IN SLOVAK POPULATION

Directory of Open Access Journals (Sweden)

Jozef Sokol

2010-07-01

Full Text Available Pesticides used in the agriculture have to be applied according to the requirements of good agricultural practice and appropriate law. Pesticides leave detectable residues in agricultural crops, raw materials and ecosystem components. Pesticides reach the human population through the food chain. Information on the type and concentration of pesticide residues in food is in Slovakia collected trough the monitoring programs. Health risks associated with pesticides contaminants in human nutrition are very important and are recently studied by several expert groups. Prerequisite programs are necessary to protect public health. Risk analysis and monitoring of the population burden by pesticide contaminants have to be performed in expert level. The general strategy for assessment of toxicity of pesticides is listed by the World health Organisation. Scientific risk assessment is the basis for taking action and making the legislation at national and European community level.doi:10.5219/69

Influência do período de restrição hídrica na atividade residual de isoxaflutole no solo Influence of drought periods on the residual activity of isoxaflutole in soil

Directory of Open Access Journals (Sweden)

R.S. Oliveira Jr.

2006-12-01

Full Text Available O objetivo deste trabalho foi estudar a atividade residual do isoxaflutole (IFT no controle de Brachiaria decumbens sob diferentes períodos de seca, após a aplicação do herbicida, em dois solos. Para isso, foram realizados seis ensaios simultâneos, sendo utilizadas doses de 0, 230 e 270 g ha-1 de isoxaflutole em amostras de Latossolo Vermelho Distroférrico nitossólico (textura argilosa e doses de 0, 180 e 200 g ha-1 em amostras de Latossolo Vermelho distrófico (textura franco-argilo-arenosa. Em cada ensaio, foram combinados em esquema fatorial doses e períodos de seca após as aplicações do herbicida, utilizando-se B. decumbens como bioindicador da atividade residual do herbicida no solo. As avaliações de controle foram feitas aos 15, 30, 45 e 60 dias após a semeadura do bioindicador. O IFT apresentou alta estabilidade no solo de textura argilosa mesmo após três chuvas simuladas de 20 mm, espaçadas de 30 dias e seguidas de 120 dias de seca após sua aplicação. No solo de textura franco-arenosa a estabilidade foi menor, e o efeito residual (80% de controle persistiu entre 0 e 110 dias para B. decumbens, conforme dose, períodos de seca e data de avaliação após a semeadura. Esse fato evidenciou que, à medida que aumenta o tempo e o número de irrigações entre a aplicação do herbicida e a semeadura do bioindicador, há redução no potencial efetivo de controle de IFT no Latossolo Vermelho distrófico.This work was carried out to evaluate the residual activity of isoxaflutole (IFT in Brachiaria decumbens control after different simulated drought conditions following herbicide application in two soils. Six simultaneous experiments were performed, using rates of 0, 230 and 270 g ha-1 of IFT in samples of a heavy clay soil and of 0, 180 and 200 g ha-1 in samples of a sandy clay loam soil. In each experiment, rates of IFT were combined in a factorial scheme with drought periods after herbicide application. B. decumbens was

A Residual Approach for Balanced Truncation Model Reduction (BTMR of Compartmental Systems

Directory of Open Access Journals (Sweden)

William La Cruz

2014-05-01

Full Text Available This paper presents a residual approach of the square root balanced truncation algorithm for model order reduction of continuous, linear and time-invariante compartmental systems. Specifically, the new approach uses a residual method to approximate the controllability and observability gramians, whose resolution is an essential step of the square root balanced truncation algorithm, that requires a great computational cost. Numerical experiences are included to highlight the efficacy of the proposed approach.

Multi-Residue studies of pesticides in fermented dried cocoa beans and selected cocoa products produced in Ghana

International Nuclear Information System (INIS)

Frimpong, S. K

2011-01-01

the organochlorine, organophosphorous and synthetic pyrethroids pesticides respectively. Multivariate analysis on the residue data obtained from fermented dried cocoa beans in R-mode and Q-mode grouped the detected pesticides into currently used, previously used and drift from neighbouring crops pesticides applications. It also grouped sampled cocoa beans into four major clusters based on similarities in crop storage and farm practices. Beta-HCH (18.7 μg/kg), Gamma-chlordane (152.0 μg/kg), Methamidophos (18.5 μg/kg), Profenofos (31.8 μg/kg), Allethrin (10.5 μg/kg), Cypermethrin (32.0 μg/kg) and Fenvalerate (14.6 μg/kg) were the average residues concentrations of pesticides that exceeded the Japanese maximum residue levels (MRLs). However, all the detected pesticides with exception of Allethrin were below the MRLs for European Union. From results recorded in semi-finished and finished cocoa beans products produced in Ghana, de-shelling and roasting temperatures drastically reduced the residue levels in the cocoa products, but these were not enough solution for pesticide residues in cocoa beans. And thus raises concern about the health implication of these chemicals for domestic consumption of these products. It is highly recommended that a national quality control laboratory be established to continually monitor pesticides efficacy in order to avoid overdose of pesticides application.[au

Application of preservatives for residual fuels

International Nuclear Information System (INIS)

Gorozpe y Munoz, Tomas

2000-01-01

Due to the high costs of the combust oils (fuel oil 6) used in generators of vapor and in other treatments, makes important consider the use of preservatives that improve the operation of the units from the operative point of view and of environmental control. The author enumerates several of the problems of corrosion, of efficiency in the combustion and of thermal efficiency; in a same way it enumerates several useful preservatives, to be used in residual fuel

Measurement of residual radioactivity in cooper exposed to high energy heavy ion beam

Energy Technology Data Exchange (ETDEWEB)

Kim, Eunjoo; Nakamura, Takashi [Tohoku Univ., Sendai (Japan). Cyclotron and Radioisotope Center; Uwamino, Yoshitomo; Ito, Sachiko; Fukumura, Akifumi

1999-03-01

The residual radioactivities produced by high energy heavy ions have been measured using the heavy ion beams of the Heavy Ion Medical Accelerator (HIMAC) at National Institute of Radiological Sciences. The spatial distribution of residual radioactivities in 3.5 cm, 5.5 cm and 10 cm thick copper targets of 10 cm x 10 cm size bombarded by 290 MeV/u, 400 MeV/u-{sup 12}C ion beams and 400 MeV/u-{sup 20}Ne ion beam, respectively, were obtained by measuring the gamma-ray activities of 0.5 mm thick copper foil inserted in the target with a high purity Ge detector after about 1 hour to 6 hours irradiation. (author)

Efficacy of residual bifenthrin applied to landscape vegetation against Aedes albopictus.

Science.gov (United States)

Doyle, Melissa A; Kline, Daniel L; Allan, Sandra A; Kaufman, Phillip E

2009-06-01

The daytime biting mosquito Aedes albopictus is a nuisance pest commonly found in suburban yards. The recommended course of treatment for Ae. albopictus is to keep yards free of water-holding containers; however, infestations may require additional control methods such as residual pesticide applications to vegetation. Five plants commonly found in yards or in uncultivated areas in Gainesville, FL were chosen as substrates for evaluation of the effectiveness of residual bifenthrin against 5-7-day-old female Ae. albopictus. Knockdown of mosquitoes after 1 h of exposure was highest the day of and 7 days after treatment. Plant species clearly impacted the effectiveness of residual bifenthrin. One-hour knockdown 7 days after treatment remained high (>62%) only on azalea and holly bush vegetation. Knockdown counts 24 h after exposure demonstrated that residual efficacy of bifenthrin was highest on azalea, with >77% mortality for up to 35 days. Additional bioassays revealed significant differences in the knockdown rates of male, female, gravid, and blood-fed Ae. albopictus exposed to residual bifenthrin treatments, with the highest knockdown observed on the day of and 7 days after treatment.

Well-directed inclusion of hematology in African national cancer control plans.

Science.gov (United States)

Weaver, Meaghann; Yao, Atteby J J; Renner, Lorna; Harif, Mhamed; Lam, Catherine G

2017-07-01

In the context of a convergent call for noncommunicable disease integration in the global agenda, recognizing cross-cutting needs and opportunities in national strategies across disease fields with shared priorities in low- and middle-income settings can enhance sustainable development approaches. We reviewed publicly available cancer control plans in Africa to evaluate for inclusion of hematology needs and shared service priorities. Pediatric data remain sparse in cancer control plans. While continental Africa represents incredible diversity, recognizing shared priorities and opportunity for collaboration between oncology and hematology services and across age groups may guide prioritized cancer control efforts and reduce programmatic redundancies in resource-limited settings. © 2017 Wiley Periodicals, Inc.

The Effect of Crop Residue Application to Soil Fauna Community and Mungbean Growth (Vigna radata

Directory of Open Access Journals (Sweden)

SUGIYARTO

2000-01-01

Full Text Available Litterbag experiment was carried out to determine the effect of crop residue application to soil fauna community and mungbean growth. The experiment arranged in randomized complete design with triplicate. The four treatment application of crotalarian, rice straw and banana’s aerial stem residues as well as without residue application as control. Soil fauna community and mungbean growth measured at 8 weeks after mungbean sown. Soil fauna extracted by modified Barless-Tullgren extractor apparatus. Height and dry weight of mungbean measured as crop growth parameters. The results indicated that the soil fauna densities and diversities as well as the growth of mungbean tended to increase by the application of crop residues. The effect of the treatment decreasing in the following order: banana’s aerial stem residue > crotalarian residue > rice straw > without residue application. There were high correlation between mungbean growth and soil fauna diversities.© 2001 Jurusan Biologi FMIPA UNS SurakartaKey words:

The role of research and development work on the production costs of logging residue chips

International Nuclear Information System (INIS)

Nousiainen, I.

1998-01-01

Purchase of logging residue chips in the early 80s was mainly based on production chains in which the residues were collected with load-carrying tractors at the road-side storage, from which it was chipped or crushed directly into the trailer of a waiting lorry. Six new production chains were developed in the national Bioenergy Research Programme. Three of these are now commercial. Kotimaiset Energiat Pekka Lahti Ky has developed, on the basis of a traditional logging residue production chain, a high-efficiency EVOLUTION intermediate storage chipper, suitable for chipping of logging residues. Oy Logset Ab has developed a new type of lot-chipping chip-harvester, the LOGSET 536C. Nested containers have also been developed for the lot-chipping method. MOHA multi-purpose chipper, in which the chipping and lorry-transportation of chips have been integrated, has also been developed as a part of the research programme. In addition to these, a chipper-container lorry combination, transportation of complete logging residues, and whole- tree skidding have been developed in the project for production of logging residue chips. In the beginning of the 80s the production costs of logging residues at the place of utilization were about 52 FIM/MWh, and the average transportation distance 50 km. In 1992 the production costs, 64 FIM/MWh at the distance of 100 km, was significantly higher than the price of alternative fuels. The lowest production cost level, obtainable by the developed methods is 46 FIM/MWh

National infrastructure for detecting, controlling and monitoring radioactive materials

International Nuclear Information System (INIS)

Othman, I.

2001-01-01

Full text: The Atomic Energy Commission of Syria (AECS) has the direct responsibility to assure proper safety for handling, accounting for and controlling of nuclear materials and radioactive sources which based on a solid regulatory infrastructure , its elements contains the following items: preventing, responding, training, exchanging of information. Based on the National Law for AECS's Establishment no. 12/1976, a Ministerial Decree for Radiation Safety no. 6514 dated 8.12.1997, issued by the Prime Minister. This Decree authorizes the Syrian Atomic Energy Commission to regulate all kinds of radiation sources. It fulfills the basic requirements of radiation protection and enforce the rules and regulations. The Radiation and Nuclear Regulatory Office (RNRO) is responsible for preparing all the draft regulations. In 1999 the General Regulations for Radiation Protection was issued by the Director General of the AECS, under Decision no. 112/99 dated 3.2.1999. It is based on an IAEA publication, Safety Series no. 115 (1996), and adopted to meet the national requirements. Syria has nine Boarding Centers seeking to prevent unauthorized movement of nuclear material and radioactive sources in and out side the country. They are related to the Atomic Energy Commission (AECS), and are located at the main entrances of the country. Each is provided with the practical tools and equipment in order to assist Radiation Protection Officers (RPO) in fulfilling their commitments, by promoting greater transparency in legal transfers of radioactive materials and devices. They apply complete procedures for the safe import, export and transit of radioactive sources. The RPOs provide authorizations by issuing an entry approval document, after making sure that each concerned shipments has an authorized license from the Syrian Regulatory Body (RNRO) before permitting shipments to leave, arrive or transit across their territory, enabling law enforcement to track the legal movement of

Reactivity of Athabasca residue and of its SARA fractions during residue hydroconversion

Energy Technology Data Exchange (ETDEWEB)

Verstraete, J.; Danial-Fortain, P.; Gauthier, T.; Merdrignac, I. [IFP-Lyon, Vermaison (France); Budzinski, H. [Bordeaux Univ. (France). ISM-LPTC, UMR CNRS

2009-07-01

Residue conversion processes are becoming increasingly important because of the declining market for residual fuel oil and a greater demand for middle distillates. Ebullated-bed hydroconversion is a commercially proven technology for converting heavy feedstocks with high amounts of impurities. The process enables the conversion of atmospheric or vacuum residues at temperatures up to 440 degrees C, and at liquid hourly space velocity (LHSV) conditions in the range of 0.15 to 0.5 per hour. A 540 degrees C conversion of up to 80 weight per cent can be achieved under these conditions. This paper reported on a research study conducted at IFP Lyon in which the residue hydroconversion in a large-scale ebullated bed bench unit was investigated to determine the impact of operating conditions and feed properties on yield and product qualities. Hydrogen was added to the feed in the bench units to keep a high hydrogen partial pressure and favour the catalytic hydroconversion reactions. In a typical test, the reactor was fed with 50 g of feedstock and 0.45 g of crushed equilibrium industrial NiMo catalyst, pressurized hydrogen and quickly heated at the reaction temperature. This paper also discussed the conversion of Athabasca bitumen residue in the large-scale pilot plant and also in the small scale batch reactor. The effect of operating temperature and space velocity was examined. The reactivity of the saturates, aromatics, resins and asphaltenes (SARA) fractions of the bitumen was studied separately in order to better understand the conversion mechanisms and reactivities. The Athabasca bitumen feed and SARA fractions were also analyzed in terms of standard petroleum analysis, SARA fractionation, elemental analysis, size exclusion chromatography (SEC) and 13C NMR. Hydroconversion experiments were conducted in the batch unit at different reaction temperatures and reaction times. A comparison of small-scale batch results with those obtained with the continuous large-scale bench

Hanford Tank 241-C-106: Impact of Cement Reactions on Release of Contaminants from Residual Waste

International Nuclear Information System (INIS)

Deutsch, William J.; Krupka, Kenneth M.; Lindberg, Michael J.; Cantrell, Kirk J.; Brown, Christopher F.; Schaef, Herbert T.

2006-01-01

The CH2M HILL Hanford Group, Inc. (CH2M HILL) is producing risk/performance assessments to support the closure of single-shell tanks at the U.S. Department of Energy's Hanford Site. As part of this effort, staff at Pacific Northwest National Laboratory were asked to develop release models for contaminants of concern that are present in residual sludge remaining in tank 241-C-106 (C-106) after final retrieval of waste from the tank. Initial work to produce release models was conducted on residual tank sludge using pure water as the leaching agent. The results were reported in an earlier report. The decision has now been made to close the tanks after waste retrieval with a cementitious grout to minimize infiltration and maintain the physical integrity of the tanks. This report describes testing of the residual waste with a leaching solution that simulates the composition of water passing through the grout and contacting the residual waste at the bottom of the tank.

National Geodetic Control Stations, Geographic NAD83, NGS (2004) [geodetic_ctrl_point_la_NGS_2004

Data.gov (United States)

Louisiana Geographic Information Center — This data contains a set of geodetic control stations maintained by the National Geodetic Survey. Each geodetic control station in this dataset has either a precise...

Evaluation of resource recovery from waste incineration residues--the case of zinc.

Science.gov (United States)

Fellner, J; Lederer, J; Purgar, A; Winterstetter, A; Rechberger, H; Winter, F; Laner, D

2015-03-01

Solid residues generated at European Waste to Energy plants contain altogether about 69,000 t/a of Zn, of which more than 50% accumulates in air pollution control residues, mainly boiler and filter ashes. Intensive research activities aiming at Zn recovery from such residues recently resulted in a technical scale Zn recovery plant at a Swiss waste incinerator. By acidic leaching and subsequent electrolysis this technology (FLUREC) allows generating metallic Zn of purity>99.9%. In the present paper the economic viability of the FLUREC technology with respect to Zn recovery from different solid residues of waste incineration has been investigated and subsequently been categorised according to the mineral resource classification scheme of McKelvey. The results of the analysis demonstrate that recovery costs for Zn are highly dependent on the costs for current fly ash disposal (e.g. cost for subsurface landfilling). Assuming current disposal practice costs of 220€/ton fly ash, resulting recovery costs for Zn are generally higher than its current market price of 1.6€/kg Zn. With respect to the resource classification this outcome indicates that none of the identified Zn resources present in incineration residues can be economically extracted and thus cannot be classified as a reserve. Only for about 4800 t/a of Zn an extraction would be marginally economic, meaning that recovery costs are only slightly (less than 20%) higher than the current market price for Zn. For the remaining Zn resources production costs are between 1.5 and 4 times (7900 t/a Zn) and 10-80 times (55,300 t/a Zn) higher than the current market value. The economic potential for Zn recovery from waste incineration residues is highest for filter ashes generated at grate incinerators equipped with wet air pollution control. Copyright © 2014 Elsevier Ltd. All rights reserved.

Mapping residual stresses in PbWO4 crystals using photo-elastic analysis

International Nuclear Information System (INIS)

Lebeau, M.; Gobbi, L.; Majni, G.; Paone, N.; Pietroni, P.; Rinaldi, D.

2005-01-01

Large scintillating crystals are affected by internal stresses induced by the crystal growth temperature gradient remanence. Cutting boules (ingots) into finished crystal shapes allows for a partial tension relaxation but residual stresses remain the main cause of breaking. Quality control of residual stresses is essential in the application of Scintillating Crystals to high-energy physics calorimeters (e.g. CMS ECAL at CERN LHC). In this context the industrial process optimisation towards stress reduction is mandatory. We propose a fast technique for testing samples during the production process in order to evaluate the residual stress distribution after the first phases of mechanical processing. We mapped the stress distribution in PbWO 4 slabs cut from the same production boule. The analysis technique is based on the stress intensity determination using the photo-elastic properties of the samples. The stress distribution is mapped in each sample. The analysis shows that there are regions of high residual tension close to the seed position and at the boule periphery. These results should allow for adapting the industrial process to producing crystals with lower residual stresses

21 CFR 1405.400 - What are my responsibilities as a(n) Office of National Drug Control Policy awarding official?

Science.gov (United States)

2010-04-01

...) Responsibilities of Office of National Drug Control Policy Awarding Officials § 1405.400 What are my... 21 Food and Drugs 9 2010-04-01 2010-04-01 false What are my responsibilities as a(n) Office of National Drug Control Policy awarding official? 1405.400 Section 1405.400 Food and Drugs OFFICE OF NATIONAL...

National Spill Control School. A pilot program in environmental training. Final report

Energy Technology Data Exchange (ETDEWEB)

Oberholtzer, G.R.; Acuff, J.T.

1980-01-01

Increased environmental awareness and the amended Federal Water Pollution Control Act of 1972 required an increased level of expertise by the American Public in the field of oil spill prevention and control. The National Spill Control School was created at Corpus Christi State University to help meet this need. Drawing on the talents of a nationwide sample of experts in this field, the project team created a unique management oriented course. A review of the origination and experiences of two years of classes of this pilot program is provided in this report.

Effects of the magnesium oxide thin films' microstructures on the residual stresses

Energy Technology Data Exchange (ETDEWEB)

He, Li-jun, E-mail: helijun4@126.com [The School of Optoelectronic Engineering, Chongqing University of Posts and Telecommunications, Chongqing 400065 (China); The State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Microelectronics and Solid-State Electronics, University of Electronic Science and Technology of China, Chengdu 610054 (China); Wang, Li-yan [Electronic Information and Networking Research Institute, Collaborative Innovation Center for Information Communication Technology, Chongqing University of Posts and Telecommunications, Chongqing 400065 (China); Chen, Wei-Zhong [The School of Optoelectronic Engineering, Chongqing University of Posts and Telecommunications, Chongqing 400065 (China); Liu, Xing-zhao [The State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Microelectronics and Solid-State Electronics, University of Electronic Science and Technology of China, Chengdu 610054 (China)

2016-09-15

The MgO thin films are deposited at various inclined angles. The morphology investigated by scanning electron microscope (SEM) shows the MgO thin films deposited at high inclined angles have columnar grain. The relationships between full width high maximum (FWHM) of ω-scan, residual stresses and the inclined angles are studied. The results show the smallest FWHM of MgO (002) is 4.968°, the residual stress of MgO thin films is compressive stress, and the residual stress of MgO thin films deposited at the inclined angle of 55° is the smallest. So the microstructures of MgO thin films fabricated by the oblique angle deposition (OAD) technique effectively control the residual stresses. - Highlights: • MgO thin films are deposited by oblique angle deposition technique. • The FWHMs of MgO is the smallest at the inclined angle of 55°. • Residual stress of MgO is the smallest at the inclined angle of 55°.

Residues of {sup 14}C-paclobutrazol in mangoes

Energy Technology Data Exchange (ETDEWEB)

Costa, Maria A.; Tornisielo, Valdemar L.; Castanho, Giuliane M., E-mail: macosta@cena.usp.b [Centro de Energia Nuclear na Agricultura (CENA/USP), Piracicaba, SP (Brazil). Lab. de Ecotoxicologia

2009-07-01

Paclobutrazol (PBZ) is a growth regulator used in agricultural systems whose purpose is the control of vegetative growth, stimulating the reproductive capacity of plants. This growth regulator remains active in soil for a long time and its half-life varies with the type of soil and climatic conditions, can severely affect the development of crops. This work aimed to study the residues / metabolites of {sup 14}C-PBZ in mango pulp Tommy Atkins. The tests were performed with mangoes grown in pots stainless steel and application of {sup 14}C-PBZ was performed by the soil projection of the crown, and the mangoes tested in two periods, one year and two years after application. To evaluate the levels of residues of {sup 14}C-PBZ was realize the burning of 200 mg of pulp on biological oxidized and detached {sup 14}CO{sub 2} was detected by liquid scintillation spectrophotometer. The results were 1.65 % of residue of PBZ on fruit collected after two years of application and 4.30 % of residue of PBZ collected on fruit after a year of application and also can see that the product remained in the soil for more than one year, is translocated to the plant and reach the edible part, the pulp fruit. The identification of residual {sup 14}C- PBZ/metabolites by thin-layer chromatography did not reveal any pattern of PBZ / metabolites due to the low activity detected in the samples. Therefore, another procedure was performed for extraction and then analyzed by high performance liquid chromatography (HPLC) for detection of metabolites in the PBZ of mango pulp. (author)

The influence of electrodialytic remediation on dioxin (PCDD/PCDF) levels in fly ash and air pollution control residues

DEFF Research Database (Denmark)

Dias-Ferreira, Celia; Kirkelund, Gunvor Marie; Jensen, Pernille Erland

2016-01-01

dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF), and how these levels impact on the valorization options for fly ash and APC residue.PCDD/PCDF levels in the original residues ranged between 4.85 and 197 ng g-1, being higher for the electrostatic precipitator fly ash. The toxic equivalent...

Residual herbicide study on selected Hanford Site roadsides

Energy Technology Data Exchange (ETDEWEB)

Smith, J.L.; Kemp, C.J.; Sackschewsky, M.R.

1993-08-01

Westinghouse Hanford Company routinely treats roadsides with herbicides to control undesirable plant growth. An experiment was conducted to test perennial grass germination in soils adjacent to roadways of the Hanford Site. The primary variable was the distance from the roadside. A simple germination test was executed in a controlled-environment chamber to determine the residual effects of these applications. As expected, the greatest herbicide activity was found directly adjacent to the roadway, approximately 0 to 20 ft (0 to 6.3 m) from the roadway.

78 FR 32235 - Availability of Compliance Guide for Residue Prevention and Response to Comments

Science.gov (United States)

2013-05-29

... discrimination in all its programs and activities on the basis of race, color, national origin, gender, religion... residue during the past 12 months, and asked for comment on recent revisions to the list. FSIS also... at 202-720-2600 (voice and TTY). To file a written complaint of discrimination, write USDA, Office of...

High-Reynolds Number Circulation Control Testing in the National Transonic Facility

Science.gov (United States)

Milholen, William E., II; Jones, Gregory S.; Chan, David T.; Goodliff, Scott L.

2012-01-01

A new capability to test active flow control concepts and propulsion simulations at high Reynolds numbers in the National Transonic Facility at the NASA Langley Research Center is being developed. The first active flow control experiment was completed using the new FAST-MAC semi-span model to study Reynolds number scaling effects for several circulation control concepts. Testing was conducted over a wide range of Mach numbers, up to chord Reynolds numbers of 30 million. The model was equipped with four onboard flow control valves allowing independent control of the circulation control plenums, which were directed over a 15% chord simple-hinged flap. Preliminary analysis of the uncorrected lift data showed that the circulation control increased the low-speed maximum lift coefficient by 33%. At transonic speeds, the circulation control was capable of positively altering the shockwave pattern on the upper wing surface and reducing flow separation. Furthermore, application of the technique to only the outboard portion of the wing demonstrated the feasibility of a pneumatic based roll control capability.

Effectiveness of the compound chlorpyrifos+ cypermethrin+citronellal against Alphitobius diaperinus: laboratory analysis and residue determination in carcasses

Directory of Open Access Journals (Sweden)

GS Silva

2007-09-01

Full Text Available Effectiveness, biological security and the absence of residues in meat and/or eggs must be considered when recommending options for the control Alphitobius diaperinus in poultry production environments. This research study evaluated the effectiveness of cypermethrin+ chlorpyrifos+citronellal in the control of A. diaperinus, including analysis for the presence of residues of this compound in poultry carcasses (experimental farm. Two studies were carried out under laboratory conditions. One used paper filters a four dilutions of the compound, and the other used a container including with pulverized broiler litter and the compound. The analysis of carcasses for residues was conducted in broilers that raised in a broiler house treated (floor and/or litter with the compound at a dilution of 1:800. Birds were regularly sacrificed, submitted to necropsy, and liver, muscle and fat fragments were collected. Gas chromatography was used to identify the possible presence of any chemical residue in these samples. High effectiveness rates against A.diaperinus were observed in the two laboratory studies, as well as the absence of residues in the carcasses. This compound, used in the studied concentrations, can be recommended as a valuable alternative for the control and treatment of A. diaperinus.

78 FR 66107 - National Emissions Standards for Hazardous Air Pollutants Residual Risk and Technology Review for...

Science.gov (United States)

2013-11-04

... estimate VCS voluntary consensus standards WWW world wide web Organization of this Document. The... oxidizer RTR residual risk and technology review SAB Science Advisory Board SBA Small Business... acceptable in the world in which we live'' (Risk Report at 178, quoting NRDC v. EPA, 824 F.2d 1146, 1165 (D.C...

Identification of residue pairing in interacting β-strands from a predicted residue contact map.

Science.gov (United States)

Mao, Wenzhi; Wang, Tong; Zhang, Wenxuan; Gong, Haipeng

2018-04-19

Despite the rapid progress of protein residue contact prediction, predicted residue contact maps frequently contain many errors. However, information of residue pairing in β strands could be extracted from a noisy contact map, due to the presence of characteristic contact patterns in β-β interactions. This information may benefit the tertiary structure prediction of mainly β proteins. In this work, we propose a novel ridge-detection-based β-β contact predictor to identify residue pairing in β strands from any predicted residue contact map. Our algorithm RDb 2 C adopts ridge detection, a well-developed technique in computer image processing, to capture consecutive residue contacts, and then utilizes a novel multi-stage random forest framework to integrate the ridge information and additional features for prediction. Starting from the predicted contact map of CCMpred, RDb 2 C remarkably outperforms all state-of-the-art methods on two conventional test sets of β proteins (BetaSheet916 and BetaSheet1452), and achieves F1-scores of ~ 62% and ~ 76% at the residue level and strand level, respectively. Taking the prediction of the more advanced RaptorX-Contact as input, RDb 2 C achieves impressively higher performance, with F1-scores reaching ~ 76% and ~ 86% at the residue level and strand level, respectively. In a test of structural modeling using the top 1 L predicted contacts as constraints, for 61 mainly β proteins, the average TM-score achieves 0.442 when using the raw RaptorX-Contact prediction, but increases to 0.506 when using the improved prediction by RDb 2 C. Our method can significantly improve the prediction of β-β contacts from any predicted residue contact maps. Prediction results of our algorithm could be directly applied to effectively facilitate the practical structure prediction of mainly β proteins. All source data and codes are available at http://166.111.152.91/Downloads.html or the GitHub address of https://github.com/wzmao/RDb2C .

Residuals and the Residual-Based Statistic for Testing Goodness of Fit of Structural Equation Models

Science.gov (United States)

Foldnes, Njal; Foss, Tron; Olsson, Ulf Henning

2012-01-01

The residuals obtained from fitting a structural equation model are crucial ingredients in obtaining chi-square goodness-of-fit statistics for the model. The authors present a didactic discussion of the residuals, obtaining a geometrical interpretation by recognizing the residuals as the result of oblique projections. This sheds light on the…

Changes in chlamydia control activities in Europe between 2007 and 2012: A cross-national survey

DEFF Research Database (Denmark)

van den Broek, I; Andersen, Berit; Herrmann, B

2015-01-01

Background: In 2012, the levels of chlamydia control activities including primary prevention, effective case management with partner management and surveillance were assessed in 2012 across countries in the European Union and European Economic Area (EU/EEA), on initiative of the European Centre...... indicators of chlamydia prevention and control activities; countries were assigned to one of five categories of chlamydia control. Results: In 2012, more countries than in 2007 reported availability of national chlamydia case management guidelines (80% vs. 68%), opportunistic chlamydia testing (68% vs. 44......%) and consistent use of nucleic acid amplification tests (64% vs. 36%). The number of countries reporting having a national sexually transmitted infection control strategy or a surveillance system for chlamydia did not change notably. In 2012, most countries (18/25, 72%) had implemented primary prevention...

Machine for compacting solid residues

International Nuclear Information System (INIS)

Herzog, J.

1981-11-01

Machine for compacting solid residues, particularly bulky radioactive residues, constituted of a horizontally actuated punch and a fixed compression anvil, in which the residues are first compacted horizontally and then vertically. Its salient characteristic is that the punch and the compression anvil have embossments on the compression side and interpenetrating plates in the compression position [fr

Identification of key residues for protein conformational transition using elastic network model.

Science.gov (United States)

Su, Ji Guo; Xu, Xian Jin; Li, Chun Hua; Chen, Wei Zu; Wang, Cun Xin

2011-11-07

Proteins usually undergo conformational transitions between structurally disparate states to fulfill their functions. The large-scale allosteric conformational transitions are believed to involve some key residues that mediate the conformational movements between different regions of the protein. In the present work, a thermodynamic method based on the elastic network model is proposed to predict the key residues involved in protein conformational transitions. In our method, the key functional sites are identified as the residues whose perturbations largely influence the free energy difference between the protein states before and after transition. Two proteins, nucleotide binding domain of the heat shock protein 70 and human/rat DNA polymerase β, are used as case studies to identify the critical residues responsible for their open-closed conformational transitions. The results show that the functionally important residues mainly locate at the following regions for these two proteins: (1) the bridging point at the interface between the subdomains that control the opening and closure of the binding cleft; (2) the hinge region between different subdomains, which mediates the cooperative motions between the corresponding subdomains; and (3) the substrate binding sites. The similarity in the positions of the key residues for these two proteins may indicate a common mechanism in their conformational transitions.

Residue Levels and Risk Assessment of Pesticides in Pistachio Nuts in Iran

Directory of Open Access Journals (Sweden)

Azadeh Emami

2017-02-01

Full Text Available Background: Pistachio is one of the main nutrients, not only as a strategic crop but also as a main type of nut, in Iranians’ food cycle. The aim of this study was to measure the relative safety of Iranian pistachio based on the standard pesticide’s residue limits, which should be monitored and assessed in the cultivation of pistachio in order to confirm its public health. Methods: Fifty samples of pistachios of different brands were collected from Tehran markets in 2015. QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe sampling method was used in order to determine the pesticide’s residue in the pistachio nuts by Gas chromatography/Mass spectrometry (GC/MS.The method was validated with related parameters. Recovery took place at five concentration rates (n=3 ranging from 81.40% to 93.08% with the majority of RelativeStandard Deviation being lower than 20%. Limits of detection and quantification for all the pesticides were 2µg/kg and10µg/kg, respectively. The validated method seemed to be appropriate for the analysis of pesticide’s residue in pistachio nuts. Results: Identified pesticides included Fenitrothion, Carbaryl and Diazinon. Detectable pesticide’s residue existed in 10% (5 samples of the samples. Conclusion: All the results were compared with the Iran’s National Standards and the European Maximum Residue Limits. As compared to the acceptable daily intake, the calculated daily intake of each pesticide was much lower than the standard level, which could not cause any public health problem.

Incremental cost of implementing residual insecticide treatment with delthametrine on top of intensive routine Aedes aegypti control.

Science.gov (United States)

Baly, Alberto; Gonzalez, Karelia; Cabrera, Pedro; Popa, Julio C; Toledo, Maria E; Hernandez, Claudia; Montada, Domingo; Vanlerberghe, Veerle; Van der Stuyft, Patrick

2016-05-01

Information on the cost of implementing residual insecticide treatment (RIT) for Aedes control is scarce. We evaluated the incremental cost on top of intensive conventional routine activities of the Aedes control programme (ACP) in the city of Santiago de Cuba, Cuba. We conducted the cost analysis study in 2011-2012, from the perspective of the ACP. Data sources were bookkeeping records, activity registers of the Provincial ACP Centre and the accounts of an RIT implementation study in 21 clusters of on average four house blocks comprising 5180 premises. The annual cost of the routine ACP activities was 19.66 US$ per household. RIT applications in rounds at 4-month intervals covering, on average, 97.2% and using 8.5 g of delthametrine annually per household, cost 3.06 US$ per household per year. Delthametrine comprised 66.5% of this cost; the additional cost for deploying RIT comprised 15.6% of the total ACP routine cost and 27% of the cost related to routine adult stage Aedes control. The incremental cost of implementing RIT is high. It should be weighed against the incremental effect on the burden caused by the array of pathogens transmitted by Aedes. The cost could be reduced if the insecticide became cheaper, by limiting the number of yearly applications or by targeting transmission hot spots. © 2016 John Wiley & Sons Ltd.

Inventories of woody residues and solid wood waste in the United States, 2002

Science.gov (United States)

David B. McKeever

2004-01-01

Large amounts of woody residues and wood waste are generated annually in the United States. In 2002, an estimated 240 million metric tons was generated during the extraction of timber from the Nation’s forests, from forestry cultural operations, in the conversion of forest land to nonforest uses, in the initial processing of roundwood timber into usable products, in...

Analytical solutions for peak and residual uplift resistance of pipelines

Energy Technology Data Exchange (ETDEWEB)

Nixon, J.F. [Nixon Geotech Ltd., Calgary, AB (Canada); Oswell, J.M. [Naviq Consulting Inc., Calgary, AB (Canada)

2010-07-01

Frost heave can occur on cold pipelines that traverse unfrozen, non permafrost terrain. The stresses experienced by the pipeline are partly a function of the strength of the soil on the non heaving side of the frozen-unfrozen interface. This paper proposed three analytical solutions to estimate the soil uplift resistance by considering the pipeline and soil to act similar to a strip footing, a punching shear failure, and by considering the formation of horizontal crack emanating from the spring line of the pipe. Peak uplift resistance and residual uplift resistance were discussed. Results for full scale pipe and for laboratory scale model pipes were presented, with particular reference to cover depth, temperature and crack width; and limits to residual uplift resistance. It was concluded that the peak uplift resistance and the residual uplift resistance are generally independent and controlled by different factors. The peak resistance is related directly to pipe diameter, and less strongly dependent on springline depth. It is also strongly dependent on soil temperature. However, the residual uplift resistance is strongly dependent on burial depth, weakly dependent on pipe displacement rate and also on soil temperature. 15 refs., 19 figs.

Proceedings of the Second National Science and Technology Forum

International Nuclear Information System (INIS)

2005-01-01

In Zambia, a lot of research work has been carried out in Science and Technology without a matching public awareness of the achievements and potential benefits. It is for this reason the National Science and Technology Council hosted the Second National Science and Technology Forum to publicise and promote broad national prioties in Science and Technology research. Highlights included the presentation of papers on residue effect of partially acidulated phosphate rock,the fluorencenceand absortion of white and dyed cotton fabricsand the intergation of indigenious knowledge and technologies in national development among others

Protein-protein docking with dynamic residue protonation states.

Directory of Open Access Journals (Sweden)

Krishna Praneeth Kilambi

2014-12-01

Full Text Available Protein-protein interactions depend on a host of environmental factors. Local pH conditions influence the interactions through the protonation states of the ionizable residues that can change upon binding. In this work, we present a pH-sensitive docking approach, pHDock, that can sample side-chain protonation states of five ionizable residues (Asp, Glu, His, Tyr, Lys on-the-fly during the docking simulation. pHDock produces successful local docking funnels in approximately half (79/161 the protein complexes, including 19 cases where standard RosettaDock fails. pHDock also performs better than the two control cases comprising docking at pH 7.0 or using fixed, predetermined protonation states. On average, the top-ranked pHDock structures have lower interface RMSDs and recover more native interface residue-residue contacts and hydrogen bonds compared to RosettaDock. Addition of backbone flexibility using a computationally-generated conformational ensemble further improves native contact and hydrogen bond recovery in the top-ranked structures. Although pHDock is designed to improve docking, it also successfully predicts a large pH-dependent binding affinity change in the Fc-FcRn complex, suggesting that it can be exploited to improve affinity predictions. The approaches in the study contribute to the goal of structural simulations of whole-cell protein-protein interactions including all the environmental factors, and they can be further expanded for pH-sensitive protein design.

Residual stress concerns in containment analysis

International Nuclear Information System (INIS)

Costantini, F.; Kulak, R. F.; Pfeiffer, P. A.

1997-01-01

The manufacturing of steel containment vessels starts with the forming of flat plates into curved plates. A steel containment structure is made by welding individual plates together to form the sections that make up the complex shaped vessels. The metal forming and welding process leaves residual stresses in the vessel walls. Generally, the effect of metal forming residual stresses can be reduced or virtually eliminated by thermally stress relieving the vesseL In large containment vessels this may not be practical and thus the residual stresses due to manufacturing may become important. The residual stresses could possibly tiect the response of the vessel to internal pressurization. When the level of residual stresses is significant it will affect the vessel's response, for instance the yielding pressure and possibly the failure pressure. The paper will address the effect of metal forming residual stresses on the response of a generic pressure vessel to internal pressurization. A scoping analysis investigated the effect of residual forming stresses on the response of an internally pressurized vessel. A simple model was developed to gain understanding of the mechanics of the problem. Residual stresses due to the welding process were not considered in this investigation

End-of-life vehicle recycling : state of the art of resource recovery from shredder residue.

Energy Technology Data Exchange (ETDEWEB)

Jody, B. J.; Daniels, E. J.; Energy Systems

2007-03-21

Each year, more than 50 million vehicles reach the end of their service life throughout the world. More than 95% of these vehicles enter a comprehensive recycling infrastructure that includes auto parts recyclers/dismantlers, remanufacturers, and material recyclers (shredders). Today, about 75% of automotive materials are profitably recycled via (1) parts reuse and parts and components remanufacturing and (2) ultimately by the scrap processing (shredding) industry. The process by which the scrap processors recover metal scrap from automobiles involves shredding the obsolete automobiles, along with other obsolete metal-containing products (such as white goods, industrial scrap, and demolition debris), and recovering the metals from the shredded material. The single largest source of recycled ferrous scrap for the iron and steel industry is obsolete automobiles. The non-metallic fraction that remains after the metals are recovered from the shredded materials (about 25% of the weight of the vehicle)--commonly called shredder residue--is disposed of in landfills. Over the past 10 to 15 years, a significant amount of research and development has been undertaken to enhance the recycle rate of end-of-life vehicles (ELVs), including enhancing dismantling techniques and improving remanufacturing operations. However, most of the effort has focused on developing technology to recover materials, such as polymers, from shredder residue. To make future vehicles more energy efficient, more lighter-weight materials--primarily polymers and polymer composites--will be used in manufacturing these vehicles. These materials increase the percentage of shredder residue that must be disposed of, compared with the percentage of metals. Therefore, as the complexity of automotive materials and systems increases, new technologies will be required to sustain and maximize the ultimate recycling of these materials and systems at end-of-life. Argonne National Laboratory (Argonne), in cooperation

Residual Negative Symptoms Differentiate Cognitive Performance in Clinically Stable Patients with Schizophrenia and Bipolar Disorder

Directory of Open Access Journals (Sweden)

Rajeev Krishnadas

2014-01-01

Full Text Available Cognitive deficits in various domains have been shown in patients with bipolar disorder and schizophrenia. The purpose of the present study was to examine if residual psychopathology explained the difference in cognitive function between clinically stable patients with schizophrenia and bipolar disorder. We compared the performance on tests of attention, visual and verbal memory, and executive function of 25 patients with schizophrenia in remission and 25 euthymic bipolar disorder patients with that of 25 healthy controls. Mediation analysis was used to see if residual psychopathology could explain the difference in cognitive function between the patient groups. Both patient groups performed significantly worse than healthy controls on most cognitive tests. Patients with bipolar disorder displayed cognitive deficits that were milder but qualitatively similar to those of patients with schizophrenia. Residual negative symptoms mediated the difference in performance on cognitive tests between the two groups. Neither residual general psychotic symptoms nor greater antipsychotic doses explained this relationship. The shared variance explained by the residual negative and cognitive deficits that the difference between patient groups may be explained by greater frontal cortical neurophysiological deficits in patients with schizophrenia, compared to bipolar disorder. Further longitudinal work may provide insight into pathophysiological mechanisms that underlie these deficits.

National control and eradication program of bovine tuberculosis in Chile.

Science.gov (United States)

Max, Vanessa; Paredes, Luis; Rivera, Alejandro; Ternicier, Claudio

2011-07-05

There have been reports of the presence of bovine tuberculosis (TB) in Chile for more than 100 years. Several prevalence studies have revealed that there is a wide spectrum of disease across the country with certain geographic areas where the disease is endemic through to other geographic areas where infection is sporadic and at very low prevalence. In 2009, this information was used to divide Chile into different geographic zones based on prevalence rates. This will enable the correct actions to be undertaken to reduce the prevalence of TB. Thus the northern part of Chile which has a medium to high prevalence of TB will be categorized as a control zone. In contrast, the southern part of Chile which has a high proportion of the bovine population, has a low prevalence of TB and will be classified as an eradication zone (Paredes, 2008). Although there have been several past attempts to create a national control and eradication program in Chile, none has been successful. A national program is proposed, and outlined in this paper. Progress toward program initiation in 2009 has been difficult, mostly because of the global economic crisis, difficulties in the milk and meat industry, and social and political issues. Copyright © 2011 Elsevier B.V. All rights reserved.

Thermal treatment of solid residues from WtE units: a review.

Science.gov (United States)

Lindberg, Daniel; Molin, Camilla; Hupa, Mikko

2015-03-01

Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field. Copyright © 2015 Elsevier Ltd. All rights reserved.

Applications of bauxite residue: A mini-review.

Science.gov (United States)

Verma, Ajay S; Suri, Narendra M; Kant, Suman

2017-10-01

Bauxite residue is the waste generated during alumina production by Bayer's process. The amount of bauxite residue (40-50 wt%) generated depends on the quality of bauxite ore used for the processing. High alkalinity and high caustic content in bauxite residue causes environmental risk for fertile soil and ground water contamination. The caustic (NaOH) content in bauxite residue leads to human health risks, like dermal problems and irritation to eyes. Moreover, disposal of bauxite residue requires a large area; such problems can only be minimised by utilising bauxite residue effectively. For two decades, bauxite residue has been used as a binder in cement industries and filler/reinforcement for composite materials in the automobile industry. Valuable metals and oxides, like alumina (Al 2 O 3 ), titanium oxide (TiO 2 ) and iron oxide Fe 2 O 3 , were extracted from bauxite residue to reduce waste. Bauxite residue was utilised in construction and structure industries to make geopolymers. It was also used in the making of glass-ceramics and a coating material. Recently bauxite residue has been utilised to extract rare earth elements like scandium (Sc), yttrium (Y), lanthanum (La), cerium (Ce), neodymium (Nd) and dysprosium (Dy). In this review article, the mineralogical characteristics of bauxite residue are summarised and current progresses on utilisation of bauxite residue in different fields of science and engineering are presented in detail.

Management of NORM Residues

International Nuclear Information System (INIS)

2013-06-01

The IAEA attaches great importance to the dissemination of information that can assist Member States in the development, implementation, maintenance and continuous improvement of systems, programmes and activities that support the nuclear fuel cycle and nuclear applications, and that address the legacy of past practices and accidents. However, radioactive residues are found not only in nuclear fuel cycle activities, but also in a range of other industrial activities, including: - Mining and milling of metalliferous and non-metallic ores; - Production of non-nuclear fuels, including coal, oil and gas; - Extraction and purification of water (e.g. in the generation of geothermal energy, as drinking and industrial process water; in paper and pulp manufacturing processes); - Production of industrial minerals, including phosphate, clay and building materials; - Use of radionuclides, such as thorium, for properties other than their radioactivity. Naturally occurring radioactive material (NORM) may lead to exposures at some stage of these processes and in the use or reuse of products, residues or wastes. Several IAEA publications address NORM issues with a special focus on some of the more relevant industrial operations. This publication attempts to provide guidance on managing residues arising from different NORM type industries, and on pertinent residue management strategies and technologies, to help Member States gain perspectives on the management of NORM residues

Immobilization of acid digestion residue

International Nuclear Information System (INIS)

Greenhalgh, W.O.; Allen, C.R.

1983-01-01

Acid digestion treatment of nuclear waste is similar to incineration processes and results in the bulk of the waste being reduced in volume and weight to some residual solids termed residue. The residue is composed of various dispersible solid materials and typically contains the resultant radioactivity from the waste. This report describes the immobilization of the residue in portland cement, borosilicate glass, and some other waste forms. Diagrams showing the cement and glass virtification parameters are included in the report as well as process steps and candidate waste product forms. Cement immobilization is simplest and probably least expensive; glass vitrification exhibits the best overall volume reduction ratio

Biotransformación del pelo residual de curtiembres

Directory of Open Access Journals (Sweden)

Ruth Viviana Numpaque

2016-12-01

Full Text Available La industria de curtiembres genera una alta carga contaminante representada por residuos líquidos, sólidos y gaseosos. Entre los residuos sólidos, el pelo residual es vertido directamente al río Bogotá y/o en rellenos sanitarios, desencadenando serios conflictos de orden ambiental, social y económico. El objetivo de esta investigación fue evaluar la capacidad de los microorganismos del EM y Agroplux en la transformación del pelo residual en compost. Se evaluaron tres tratamientos con pelo residual y materiales orgánicos de plaza en diferentes porcentajes y dos controles, utilizando el diseño completamente al azar, con tres repeticiones. Durante el compostaje se determinaron las variables temperatura, formación de agregados, pH y conductividad eléctrica. El desarrollo de la temperatura ocurrió en ciclos que concordaron con los volteos y re-inoculaciones. En el tercer ciclo el mayor incremento de temperatura fue obtenido en los tres tratamientos, cuando ya se había agotado la mayor parte de los residuos orgánicos. La formación de agregados indicó que el proceso se llevó a efecto principalmente en el tratamiento con 20% de pelo residual más 80% de residuos orgánicos. Además de su color oscuro y la ausencia de olor y fragmentos, el compost producido mediante dicho tratamiento mostró la conductividad eléctrica más baja y un pH casi neutro. Se concluye que los microorganismos del EM y Agroplux tienen capacidad para transformar el pelo residual en compost y por lo tanto representan una alternativa viable para la continuación del funcionamiento de la industria de curtiembres en Villapinzón (Cundinamarca y en otras regiones de Colombia.

Lavandula angustifolia Mill. Oil and Its Active Constituent Linalyl Acetate Alleviate Pain and Urinary Residual Sense after Colorectal Cancer Surgery: A Randomised Controlled Trial

Directory of Open Access Journals (Sweden)

So Hyun Yu

2017-01-01

Full Text Available Pain and urinary symptoms following colorectal cancer (CRC surgery are frequent and carry a poor recovery. This study tested the effects of inhalation of Lavandula angustifolia Mill. (lavender oil or linalyl acetate on pain relief and lower urinary tract symptoms (LUTS following the removal of indwelling urinary catheters from patients after CRC surgery. This randomised control study recruited 66 subjects with indwelling urinary catheters after undergoing CRC surgery who later underwent catheter removal. Patients inhaled 1% lavender, 1% linalyl acetate, or vehicle (control group for 20 minutes. Systolic and diastolic blood pressure (BP, heart rate, LUTS, and visual analog scales of pain magnitude and quality of life (QoL regarding urinary symptoms were measured before and after inhalation. Systolic BP, diastolic BP, heart rate, LUTS, and QoL satisfaction with urinary symptoms were similar in the three groups. Significant differences in pain magnitude and urinary residual sense of indwelling catheters were observed among the three groups, with inhalation of linalyl acetate being significantly more effective than inhalation of lavender or vehicle. Inhalation of linalyl acetate is an effective nursing intervention to relieve pain and urinary residual sense of indwelling urinary catheters following their removal from patients who underwent CRC surgery.

Lavandula angustifolia Mill. Oil and Its Active Constituent Linalyl Acetate Alleviate Pain and Urinary Residual Sense after Colorectal Cancer Surgery: A Randomised Controlled Trial

Science.gov (United States)

Yu, So Hyun

2017-01-01

Pain and urinary symptoms following colorectal cancer (CRC) surgery are frequent and carry a poor recovery. This study tested the effects of inhalation of Lavandula angustifolia Mill. (lavender) oil or linalyl acetate on pain relief and lower urinary tract symptoms (LUTS) following the removal of indwelling urinary catheters from patients after CRC surgery. This randomised control study recruited 66 subjects with indwelling urinary catheters after undergoing CRC surgery who later underwent catheter removal. Patients inhaled 1% lavender, 1% linalyl acetate, or vehicle (control group) for 20 minutes. Systolic and diastolic blood pressure (BP), heart rate, LUTS, and visual analog scales of pain magnitude and quality of life (QoL) regarding urinary symptoms were measured before and after inhalation. Systolic BP, diastolic BP, heart rate, LUTS, and QoL satisfaction with urinary symptoms were similar in the three groups. Significant differences in pain magnitude and urinary residual sense of indwelling catheters were observed among the three groups, with inhalation of linalyl acetate being significantly more effective than inhalation of lavender or vehicle. Inhalation of linalyl acetate is an effective nursing intervention to relieve pain and urinary residual sense of indwelling urinary catheters following their removal from patients who underwent CRC surgery. PMID:28154606

Integrated vector management for malaria control

Directory of Open Access Journals (Sweden)

Impoinvil Daniel E

2008-12-01

Full Text Available Abstract Integrated vector management (IVM is defined as "a rational decision-making process for the optimal use of resources for vector control" and includes five key elements: 1 evidence-based decision-making, 2 integrated approaches 3, collaboration within the health sector and with other sectors, 4 advocacy, social mobilization, and legislation, and 5 capacity-building. In 2004, the WHO adopted IVM globally for the control of all vector-borne diseases. Important recent progress has been made in developing and promoting IVM for national malaria control programmes in Africa at a time when successful malaria control programmes are scaling-up with insecticide-treated nets (ITN and/or indoor residual spraying (IRS coverage. While interventions using only ITNs and/or IRS successfully reduce transmission intensity and the burden of malaria in many situations, it is not clear if these interventions alone will achieve those critical low levels that result in malaria elimination. Despite the successful employment of comprehensive integrated malaria control programmes, further strengthening of vector control components through IVM is relevant, especially during the "end-game" where control is successful and further efforts are required to go from low transmission situations to sustained local and country-wide malaria elimination. To meet this need and to ensure sustainability of control efforts, malaria control programmes should strengthen their capacity to use data for decision-making with respect to evaluation of current vector control programmes, employment of additional vector control tools in conjunction with ITN/IRS tactics, case-detection and treatment strategies, and determine how much and what types of vector control and interdisciplinary input are required to achieve malaria elimination. Similarly, on a global scale, there is a need for continued research to identify and evaluate new tools for vector control that can be integrated with

Drugs’ maximal residual limits determination methodology and waiting period’s establishing, in the light of E.U. regulations

Directory of Open Access Journals (Sweden)

Cristina , T. Romeo

2008-12-01

Full Text Available Communitary concept’s related to the drug residues assumption is essential to Romania’s full integration amongst the countries where alimentary security and human consumer’s security have had become national policy. In this respect a concise enumeration of E.U. basic legislative notions, with the specific terminology and of technicalpremises presentation, it is proposed in the aim of Communitary veterinary medicinal product’s residues evaluation as well the MRL’s determination phases in the light of 2377/90 EU Regulation’s understanding.

Improving bovine udder health: A national mastitis control program in the Netherlands

NARCIS (Netherlands)

Lam, T.J.G.M.; Borne, van den B.H.P.; Jansen, J.; Huijps, K.; Veersen, J.C.L.; Schaick, van G.; Hogeveen, H.

2013-01-01

Because of increasing bulk milk somatic cell counts and continuous clinical mastitis problems in a substantial number of herds, a national mastitis control program was started in 2005 to improve udder health in the Netherlands. The program started with founding the Dutch Udder Health Centre (UGCN),

Residual stress characterization of steel TIG welds by neutron diffraction and by residual magnetic stray field mappings

Science.gov (United States)

Stegemann, Robert; Cabeza, Sandra; Lyamkin, Viktor; Bruno, Giovanni; Pittner, Andreas; Wimpory, Robert; Boin, Mirko; Kreutzbruck, Marc

2017-03-01

The residual stress distribution of tungsten inert gas welded S235JRC+C plates was determined by means of neutron diffraction (ND). Large longitudinal residual stresses with maxima around 600 MPa were found. With these results as reference, the evaluation of residual stress with high spatial resolution GMR (giant magneto resistance) sensors was discussed. The experiments performed indicate a correlation between changes in residual stresses (ND) and the normal component of local residual magnetic stray fields (GMR). Spatial variations in the magnetic field strength perpendicular to the welds are in the order of the magnetic field of the earth.

Quantitative analysis of residual protein contamination of podiatry instruments reprocessed through local and central decontamination units.

Science.gov (United States)

Smith, Gordon Wg; Goldie, Frank; Long, Steven; Lappin, David F; Ramage, Gordon; Smith, Andrew J

2011-01-10

The cleaning stage of the instrument decontamination process has come under increased scrutiny due to the increasing complexity of surgical instruments and the adverse affects of residual protein contamination on surgical instruments. Instruments used in the podiatry field have a complex surface topography and are exposed to a wide range of biological contamination. Currently, podiatry instruments are reprocessed locally within surgeries while national strategies are favouring a move toward reprocessing in central facilities. The aim of this study was to determine the efficacy of local and central reprocessing on podiatry instruments by measuring residual protein contamination of instruments reprocessed by both methods. The residual protein of 189 instruments reprocessed centrally and 189 instruments reprocessed locally was determined using a fluorescent assay based on the reaction of proteins with o-phthaldialdehyde/sodium 2-mercaptoethanesulfonate. Residual protein was detected on 72% (n = 136) of instruments reprocessed centrally and 90% (n = 170) of instruments reprocessed locally. Significantly less protein (p podiatry instruments when protein contamination is considered, though no significant difference was found in residual protein between local decontamination unit and central decontamination unit processes for Blacks files. Further research is needed to undertake qualitative identification of protein contamination to identify any cross contamination risks and a standard for acceptable residual protein contamination applicable to different instruments and specialities should be considered as a matter of urgency.

National Ignition Facility TestController for automated and manual testing

Energy Technology Data Exchange (ETDEWEB)

Zielinski, Jason, E-mail: fishler2@llnl.gov [Lawrence Livermore National Laboratory, Livermore, CA 94551 (United States)

2012-12-15

The Controls and Information Systems (CIS) organization for the National Ignition Facility (NIF) has developed controls, configuration and analysis software applications that combine for several million lines of code. The team delivers updates throughout the year, from major releases containing hundreds of changes to patch releases containing a small number of focused updates. To ensure the quality of each delivery, manual and automated tests are performed using the NIF TestController test infrastructure. The TestController system provides test inventory management, test planning, automated and manual test execution, release testing summaries and results search, all through a web browser interface. As part of the three-stage software testing strategy, the NIF TestController system helps plan, evaluate and track the readiness of each release to the NIF production environment. After several years of use in testing NIF software applications, the TestController's manual testing features have been leveraged for verifying the installation and operation of NIF Target Diagnostic hardware. The TestController recorded its first test results in 2004. Today, the system has recorded the execution of more than 160,000 tests and continues to play a central role in ensuring that NIF hardware and software meet the requirements of a high reliability facility. This paper describes the TestController system and discusses its use in assuring the quality of software delivered to the NIF.

National Ignition Facility TestController for automated and manual testing

International Nuclear Information System (INIS)

Zielinski, Jason

2012-01-01

The Controls and Information Systems (CIS) organization for the National Ignition Facility (NIF) has developed controls, configuration and analysis software applications that combine for several million lines of code. The team delivers updates throughout the year, from major releases containing hundreds of changes to patch releases containing a small number of focused updates. To ensure the quality of each delivery, manual and automated tests are performed using the NIF TestController test infrastructure. The TestController system provides test inventory management, test planning, automated and manual test execution, release testing summaries and results search, all through a web browser interface. As part of the three-stage software testing strategy, the NIF TestController system helps plan, evaluate and track the readiness of each release to the NIF production environment. After several years of use in testing NIF software applications, the TestController's manual testing features have been leveraged for verifying the installation and operation of NIF Target Diagnostic hardware. The TestController recorded its first test results in 2004. Today, the system has recorded the execution of more than 160,000 tests and continues to play a central role in ensuring that NIF hardware and software meet the requirements of a high reliability facility. This paper describes the TestController system and discusses its use in assuring the quality of software delivered to the NIF.

Implementing preventive chemotherapy through an integrated National Neglected Tropical Disease Control Program in Mali.

Directory of Open Access Journals (Sweden)

Massitan Dembélé

Full Text Available BACKGROUND: Mali is endemic for all five targeted major neglected tropical diseases (NTDs. As one of the five 'fast-track' countries supported with the United States Agency for International Development (USAID funds, Mali started to integrate the activities of existing disease-specific national control programs on these diseases in 2007. The ultimate objectives are to eliminate lymphatic filariasis, onchocerciasis and trachoma as public health problems and to reduce morbidity caused by schistosomiasis and soil-transmitted helminthiasis through regular treatment to eligible populations, and the specific objectives were to achieve 80% program coverage and 100% geographical coverage yearly. The paper reports on the implementation of the integrated mass drug administration and the lessons learned. METHODOLOGY/PRINCIPAL FINDINGS: The integrated control program was led by the Ministry of Health and coordinated by the national NTD Control Program. The drug packages were designed according to the disease endemicity in each district and delivered through various platforms to eligible populations involving the primary health care system. Treatment data were recorded and reported by the community drug distributors. After a pilot implementation of integrated drug delivery in three regions in 2007, the treatment for all five targeted NTDs was steadily scaled up to 100% geographical coverage by 2009, and program coverage has since been maintained at a high level: over 85% for lymphatic filariasis, over 90% for onchocerciasis and soil-transmitted helminthiasis, around 90% in school-age children for schistosomiasis, and 76-97% for trachoma. Around 10 million people have received one or more drug packages each year since 2009. No severe cases of adverse effects were reported. CONCLUSIONS/SIGNIFICANCE: Mali has scaled up the drug treatment to national coverage through integrated drug delivery involving the primary health care system. The successes and lessons

National Guidelines for Prevention and Control of Iron Deficiency Anemia in India

Directory of Open Access Journals (Sweden)

Asha Bellad

2018-04-01

Full Text Available Anaemia is a serious public health challenge in India with more than 50% prevalence across vulnerable groups such as pregnant women, infants, young children and adolescents. It has adverse effects on health, physical and mental productivity affecting quality of life. Guideline is any document containing recommendations about health interventions, whether these are clinical, public health or policy recommendations. The National Anemia Prevention and control guidelines have been developed taking cognizance of the current scientific evidence. The National Iron+ Initiative guidelines have been developed by the Adolescent Division of the Ministry of Health and Family Welfare (MoHFW, Government of India.  Prevention and control of anaemia is one of the key strategies of the Health, Nutrition and Population Sector Programmes for reducing maternal, neonatal and childhood mortality and improving maternal, adolescent and childhood health status. It is estimated that anaemia causes 20 per cent of maternal deaths in India.

Improved crop residue cover estimates by coupling spectral indices for residue and moisture

Science.gov (United States)

Remote sensing assessment of soil residue cover (fR) and tillage intensity will improve our predictions of the impact of agricultural practices and promote sustainable management. Spectral indices for estimating fR are sensitive to soil and residue water content, therefore, the uncertainty of estima...

77 FR 58847 - Board of Scientific Counselors, National Center for Injury Prevention and Control (BSC, NCIPC)

Science.gov (United States)

2012-09-24

... the causes, diagnosis, treatment, control, and prevention of physical and mental diseases, and other... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, National Center for Injury Prevention and Control (BSC, NCIPC) In accordance with...

78 FR 29754 - Board of Scientific Counselors, National Center for Injury Prevention and Control, (BSC, NCIPC)

Science.gov (United States)

2013-05-21

... relating to the causes, diagnosis, treatment, control, and prevention of physical and mental diseases, and... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Board of Scientific Counselors, National Center for Injury Prevention and Control, (BSC, NCIPC) In accordance with...

Statistical inference on residual life

CERN Document Server

Jeong, Jong-Hyeon

2014-01-01

This is a monograph on the concept of residual life, which is an alternative summary measure of time-to-event data, or survival data. The mean residual life has been used for many years under the name of life expectancy, so it is a natural concept for summarizing survival or reliability data. It is also more interpretable than the popular hazard function, especially for communications between patients and physicians regarding the efficacy of a new drug in the medical field. This book reviews existing statistical methods to infer the residual life distribution. The review and comparison includes existing inference methods for mean and median, or quantile, residual life analysis through medical data examples. The concept of the residual life is also extended to competing risks analysis. The targeted audience includes biostatisticians, graduate students, and PhD (bio)statisticians. Knowledge in survival analysis at an introductory graduate level is advisable prior to reading this book.

Sample-based reporting of official national control of veterinary drug residues

DEFF Research Database (Denmark)

Andersen, Jens Hinge; Jensen, Louise Grønhøj Hørbye; Madsen, Helle L.

assessment as well as risk management. The European Food Safety Authority has been assigned with the task to set up a system for data collection based on individual analytical results. A pilot project has been launched with participants from eleven Member States for parallel reporting of monitoring results...... from 2015 in aggregated form as well as individual analytical results using a standardised data model. The challenges that face the pilot participants include provisions for categorised sample information, specific method performance data, result evaluation and follow-up actions. Experience gained...

Quality control and quality assurance philosophy introduced in national personnel dosimetry service

International Nuclear Information System (INIS)

Trousil, J.; Zelenka, Z.; Kvasnicka, O.

2008-01-01

There in National Personnel Dosimetry Service (NPDS) the implementation of the control system to guarantee the credibility of the measured personal dose equivalents results was given on the basis of the international recommendations published by the European Commission and the IAEA and in particular of the decree of the SUJB No. 132/2008 Coll. The quality control and the quality assurance are carried out in all three personal dosimetry services introduced in NPDS: in the film badge, thermoluminescent (TL) and neutron dosimetry. (authors)

Pesticides residue levels in selected fruits from some Ghanaian markets

International Nuclear Information System (INIS)

Bempah, K.C.

2009-02-01

The amount of some pesticide residues in fruits was monitored at five (5) Accra Metropolis markets. Locally produced fruits (pawpaw and tomato) and imported apples were purchased from two supermarkets and three urban markets in Accra metropolis and analyzed by gas chromatography equipped with electron capture detector for pesticide residues. A total of 220 samples of fruits were extracted and analyzed for pesticide residues, mainly organochlorines (γ-HCH, δ-HCH, aldrin, heptachlor, γ-chlordane, heptachlor epoxide, α-endosulfan, p,p'-DDE, endrin, β-endosulfan, o,p'-DDT, endrin aldehyde, p,p'- DDT, endrin ketone and methoxychlor). The data showed that most of the fruit samples analyzed contain residues of the monitored pesticides above the accepted maximum residue limit (MRL) as adopted by the FAO/WHO Codex Alimentarius Commission (CAC). The results obtained showed that 38.6 % fruit samples showed results above the MRL, 48.7 % were below the MRL and 12.7 % contained no detectable level of the monitored pesticides. Data analysis of health risk estimates indicated that, particularly γ-HCH, δ-HCH, o,p'-DDT, p,p'-DDE or p,p'-DDT do not pose a direct hazard to human health, although present in the three fruits (pawpaw, tomato and apple). However, heptachlor, heptachlor epoxide, endrin aldehyde, and endrin ketone levels exceeded the reference dose, indicating a great potential for systemic toxicity, especially in children who are considered to be the most vulnerable population subgroup. Lastly, the public is aware of pesticide residues in fruits and advocates for the curtailing of pesticide use on horticulture produce or strong educational programmes for farmers on control and safer use of pesticides. (au)

National Ignition Facility (NIF) Control Network Design and Analysis

International Nuclear Information System (INIS)

Bryant, R M; Carey, R W; Claybourn, R V; Pavel, G; Schaefer, W J

2001-01-01

The control network for the National Ignition Facility (NIF) is designed to meet the needs for common object request broker architecture (CORBA) inter-process communication, multicast video transport, device triggering, and general TCP/IP communication within the NIF facility. The network will interconnect approximately 650 systems, including the embedded controllers, front-end processors (FEPs), supervisory systems, and centralized servers involved in operation of the NIF. All systems are networked with Ethernet to serve the majority of communication needs, and asynchronous transfer mode (ATM) is used to transport multicast video and synchronization triggers. CORBA software infra-structure provides location-independent communication services over TCP/IP between the application processes in the 15 supervisory and 300 FEP systems. Video images sampled from 500 video cameras at a 10-Hz frame rate will be multicast using direct ATM Application Programming Interface (API) communication from video FEPs to any selected operator console. The Ethernet and ATM control networks are used to broadcast two types of device triggers for last-second functions in a large number of FEPs, thus eliminating the need for a separate infrastructure for these functions. Analysis, design, modeling, and testing of the NIF network has been performed to provide confidence that the network design will meet NIF control requirements

Effects of logging residue management on the growth and nutriend distribution of a pinus taeda plantation in central Louisiana, USA

Science.gov (United States)

A. Tiarks; M. Elliot-Smith; R. Stagg

2004-01-01

A 37-year-old pine plantation was harvested. An experiment was established at the site with three levels of logging residue retention and two levels of weed control. By age 10 years retaining harvest residue increased pine volumes by 10 m3 ha-land weed control increased production by another 20 m3 ha

Residual diesel measurement in sand columns after surfactant/alcohol washing

International Nuclear Information System (INIS)

Martel, R.; Gelinas, P.J.

1996-01-01

A new simple gravimetric technique has been designed to determine residual oil saturation of complex hydrocarbon mixtures (e.g., diesel) in sand column experiments because reliable methods are lacking. The He/N 2 technique is based on drying of sand columns by circulating helium gas to drag oil droplets in a cold trap (liquid nitrogen). With this technique, residual diesel measurement can be performed easily immediately after alcohol/surfactant washing and in the same lab. For high residual diesel content in Ottawa sand (25 to 30 g/kg), the technique is much more accurate (± 2% or 600 mg/kg) than the standard analytical methods for the determination of mineral oil and grease. The average relative error on partial diesel dissolution in sand column estimated after alcohol/surfactant flooding (residual saturation of 10 to 15 g/kg) is as low as 5%. The precision of the He/N 2 technique is adequate to compare relative efficiency of washing solutions when partial extraction of residual oil in Ottawa sand columns is performed. However, this technique is not adapted for determination of traces of oil in sediment or for environmental control of contaminated soils. Each diesel determination by the He/N 2 technique costs less than $8 in chemical products (helium and liquid nitrogen). A simple laboratory drying setup can be built for less than $400 which makes this technique valuable for diesel analyses when a large number of tests are required

Minimal Residual Disease in Acute Myeloid Leukemia: Still a Work in Progress?

Directory of Open Access Journals (Sweden)

Federico Mosna

2017-06-01

Full Text Available Minimal residual disease evaluation refers to a series of molecular and immunophenotypical techniques aimed at detecting submicroscopic disease after therapy. As such, its application in acute myeloid leukemia has greatly increased our ability to quantify treatment response, and to determine the chemosensitivity of the disease, as the final product of the drug schedule, dose intensity, biodistribution, and the pharmakogenetic profile of the patient. There is now consistent evidence for the prognostic power of minimal residual disease evaluation in acute myeloid leukemia, which is complementary to the baseline prognostic assessment of the disease. The focus for its use is therefore shifting to individualize treatment based on a deeper evaluation of chemosensitivity and residual tumor burden. In this review, we will summarize the results of the major clinical studies evaluating minimal residual disease in acute myeloid leukemia in adults in recent years and address the technical and practical issues still hampering the spread of these techniques outside controlled clinical trials. We will also briefly speculate on future developments and offer our point of view, and a word of caution, on the present use of minimal residual disease measurements in “real-life” practice. Still, as final standardization and diffusion of the methods are sorted out, we believe that minimal residual disease will soon become the new standard for evaluating response in the treatment of acute myeloid leukemia.

Residual stress measurements by means of neutron diffraction

International Nuclear Information System (INIS)

Pintschovius, L.; Jung, V.; Macherauch, E.; Voehringer, O.

1983-01-01

A new method for the analysis of multiaxial residual stress states is presented, which is based on high resolution neutron diffraction. It is analogous to X-ray stress analysis, but the use of neutrons instead of X-rays allows the analysis of the stress distributions also in the interior of technical components in a non-destructive way. To prove the feasibility of the method, investigations of the loading stress distributions of an aluminium bar subjected to purely elastic bending were performed. Limiting factors due to the volume of the internal probe region and the sample thickness are discussed. Complete neutron residual stress analyses were carried out for a plastically deformed bending bar and a transformation-free water-quenched steel cylinder. The results are in fairly good agreement with theoretical expectations and with X-ray control measurements at the surface of the objects. (Auth.)

Effect of controlling recrystallization from the melt on the residual stress and structural properties of the Silica-clad Ge core fiber

Science.gov (United States)

Zhao, Ziwen; Cheng, Xueli; He, Ting; Xue, Fei; Zhang, Wei; Chen, Na; Wen, Jianxiang; Zeng, Xianglong; Wang, Tingyun

2017-09-01

Effect of controlling recrystallization from the melt (1000 °C) on the residual stress and structural properties of a Ge core fiber via molten core drawing (MCD) method is investigated. Ge core fibers is investigated using Raman spectroscopy, scanning electron microscope (SEM), and X-ray diffraction (XRD). Compared with the as-drawn Ge fiber, the Raman peak of the recrystallized Ge fiber shift from 300 cm-1 to 300.6 cm-1 and full width at half maximum (FWHM) decreased from 5.36 cm-1 to 4.48 cm-1. The Ge crystal grains which sizes are of 200-600 nm were formed during the process of recrystallization; the XRD peak of (1 1 1) plane is observed after recrystallization. These results show that controlling recrystallization allows the release of the thermal stress, and improvement of the crystal quality of Ge core.

Residual Structures in Latent Growth Curve Modeling

Science.gov (United States)

Grimm, Kevin J.; Widaman, Keith F.

2010-01-01

Several alternatives are available for specifying the residual structure in latent growth curve modeling. Two specifications involve uncorrelated residuals and represent the most commonly used residual structures. The first, building on repeated measures analysis of variance and common specifications in multilevel models, forces residual variances…

21 CFR 1404.635 - May the Office of National Drug Control Policy settle a debarment or suspension action?

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false May the Office of National Drug Control Policy settle a debarment or suspension action? 1404.635 Section 1404.635 Food and Drugs OFFICE OF NATIONAL DRUG CONTROL POLICY GOVERNMENTWIDE DEBARMENT AND SUSPENSION (NONPROCUREMENT) General Principles Relating to Suspension and Debarment Actions § 1404.635...

Responses of Pea (Pisum sativum Growth and Yield to Residual Effects of Organic and Urea Fertilizers from Previous Crop

Directory of Open Access Journals (Sweden)

S. Fallah

2016-07-01

Full Text Available Application of organic manure in organic farming and long-term mineralization may lead to residual effects on the succeeding crop. So, residual effects of combined cattle manure and urea fertilizer of previous crop (black cumin on growth and yield of pea were examined in a randomized complete block design. Treatments included of  cattle manure (CM, urea (U, three ratios of CM+U full dose application (2:1; 1:1; 1:2 and three ratios of CM+U split application (2:1; 1:1; 1:2, and unfertilized control to previous crop (black cumin in 2012. Pea planted without any fertilizer in 2013. There was no significant difference between control and residual of urea treatment for some parameters including dry matter in flowering stage, plant nitrogen and phosphorus concentration, plant height, yield components, grain yield and biological yield of pea. Biological and grain yields were greater under both residual of cattle manure treatment and integrated treatments compared to residual of urea treatment. The highest grain yield (4000 kg ha-1 was observed in residual of CM:U full dosed application treatment, to the extent that grain yield in this treatment indicated a 1.5-fold increase in comparison with residual of urea treatment. The highest biological yield (8325 kg ha-1 was obtained in residual of CM treatment, though it was not significant different from that of residual of CM:U (1:2 treatments. In general, although residual of urea fertilizer did not leave a notable effect on pea production, but production of this crop relying on residual of cattle manure deems effective to lowering of fertilization cost and ameliorating environmental contaminations.

Anaerobic digestion of onion residuals using a mesophilic Anaerobic Phased Solids Digester

International Nuclear Information System (INIS)

Romano, Rowena T.; Zhang, Ruihong

2011-01-01

The anaerobic digestion of onion residual from an onion processing plant was studied under batch-fed and continuously-fed mesophilic (35 ± 2 o C) conditions in an Anaerobic Phased Solids (APS) Digester. The batch digestion tests were performed at an initial loading of 2.8 gVS L -1 and retention time of 14 days. The biogas and methane yields, and volatile solids reduction from the onion residual were determined to be 0.69 ± 0.06 L gVS -1 , 0.38 ± 0.05 L CH 4 gVS -1 , and 64 ± 17%, respectively. Continuous digestion tests were carried out at organic loading rates (OLRs) of 0.5-2.0 gVS L -1 d -1 . Hydrated lime (Ca(OH) 2 ) was added to the APS-Digester along with the onion residual at 16 mg Ca(OH) 2 gVS -1 to control the pH of the biogasification reactor above 7.0. At steady state the average biogas yields were 0.51, 0.56, and 0.62 L gVS -1 for the OLRs of 0.5, 1.0, and 2.0 gVS L -1 d -1 respectively. The methane yields at steady state were 0.29, 0.32, and 0.31 L CH 4 gVS -1 for the OLRs of 0.5, 1.0, and 2.0 gVS L -1 d -1 respectively. The study shows that the digestion of onion residual required proper alkalinity and pH control, which was possible through the use of caustic chemicals. However, such chemicals will begin to have an inhibitory effect on the microbial population at high loading rates, and therefore alternative operational parameters are needed. -- Highlights: → An APS-Digester was used to study biogas production from onion solid residues. → Biogas and methane yields from onion solids were determined. → Study showed substantial findings for treating onion solid residues.

Development of irradiation technique on degradation residue of pesticide veterinary drugs and mycotoxins in food

International Nuclear Information System (INIS)

He Jiang; Huang Min; Chen Hao; Wu Ling; Gao Peng; Wang Yan; Lei Qing

2011-01-01

Irradiation technology is a new processing technology, It was widely used in food, medicines and medical supplies, chemical and other industries. In this paper, illustrated their applications in the degradation of pesticides, veterinary drugs and mycotoxins aspects residual pollution in food. Analysis of residual contaminants in food irradiation control study limitations and look forward to the prospect of food irradiation technology. (authors)

A single amino acid residue controls Ca2+ signaling by an octopamine receptor from Drosophila melanogaster.

Science.gov (United States)

Hoff, Max; Balfanz, Sabine; Ehling, Petra; Gensch, Thomas; Baumann, Arnd

2011-07-01

Rhythmic activity of cells and cellular networks plays an important role in physiology. In the nervous system oscillations of electrical activity and/or second messenger concentrations are important to synchronize neuronal activity. At the molecular level, rhythmic activity can be initiated by different routes. We have recently shown that an octopamine-activated G-protein-coupled receptor (GPCR; DmOctα1Rb, CG3856) from Drosophila initiates Ca(2+) oscillations. Here, we have unraveled the molecular basis of cellular Ca(2+) signaling controlled by the DmOctα1Rb receptor using a combination of pharmacological intervention, site-directed mutagenesis, and functional cellular Ca(2+) imaging on heterologously expressed receptors. Phosphorylation of a single amino acid residue in the third intracellular loop of the GPCR by PKC is necessary and sufficient to desensitize the receptor. From its desensitized state, DmOctα1Rb is resensitized by dephosphorylation, and a new Ca(2+) signal occurs on octopamine stimulation. Our findings show that transient changes of the receptor's surface profile have a strong effect on its physiological signaling properties. We expect that the detailed knowledge of DmOctα1Rb-dependent signal transduction fosters the identification of specific drugs that can be used for GPCR-mediated pest control, since octopamine serves important physiological and behavioral functions in arthropods.

The inertial damping of the VIRGO superattenuator and the residual motion of the mirror

Energy Technology Data Exchange (ETDEWEB)

Losurdo, Giovanni [Istituto Nazionale di Fisica Nucleare - Sezione di Firenze, Lgo E Fermi, 2, Florence (Italy)

2002-04-07

The VIRGO superattenuator (SA) is effective in suppressing seismic noise below the expected thermal noise level above 4 Hz. However, the residual mirror motion associated with the SA normal modes can saturate the interferometer control system. This motion is reduced by implementing a wideband (DC-5 Hz) multidimensional active control (the so-called inertial damping) which makes use of both accelerometers and position sensors and of a digital signal processing (DSP) system. Feedback forces are exerted by coil-magnet actuators on the top of an inverted pendulum pre-isolator stage. The residual root mean square motion of the mirror in 10 s is less than 0.1 {mu}m.

Computing Decoupled Residuals for Compact Disc Players

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Stoustrup, Jakob; Andersen, Palle

2006-01-01

a pair of residuals generated by Compact Disc Player. However, these residuals depend on the performance of position servos in the Compact Disc Player. In other publications of the same authors a pair of decoupled residuals is derived. However, the computation of these alternative residuals has been...

Controlling hepatitis C in Rwanda: a framework for a national response.

Science.gov (United States)

Mbituyumuremyi, Aimable; Van Nuil, Jennifer Ilo; Umuhire, Jeanne; Mugabo, Jules; Mwumvaneza, Mutagoma; Makuza, Jean Damascene; Umutesi, Justine; Nsanzimana, Sabin; Gupta, Neil

2018-01-01

With the introduction of direct-acting antiviral drugs, treatment of hepatitis C is both highly effective and tolerable. Access to treatment for patients, however, remains limited in low- and middle-income countries due to the lack of supportive health infrastructure and the high cost of treatment. Poorer countries are being encouraged by international bodies to organize public health responses that would facilitate the roll-out of care and treatment on a national scale. Yet few countries have documented formal plans and policies. Here, we outline the approach taken in Rwanda to a public health framework for hepatitis C control and care within the World Health Organization hepatitis health sector strategy. This includes the development and implementation of policies and programmes, prevention efforts, screening capacity, treatment services and strategic information systems. We highlight key successes by the national programme for the control and management of hepatitis C: establishment of national governance and planning; development of diagnostic capacity; approval and introduction of direct-acting antiviral treatments; training of key personnel; generation of political will and leadership; and fostering of key strategic partnerships. Existing challenges and next steps for the programme include developing a detailed monitoring and evaluation framework and tools for monitoring of viral hepatitis. The government needs to further decentralize care and integrate hepatitis C management into routine clinical services to provide better access to diagnosis and treatment for patients. Introducing rapid diagnostic tests to public health-care facilities would help to increase case-finding. Increased public and private financing is essential to support care and treatment services.

Characterisation and management of concrete grinding residuals.

Science.gov (United States)

Kluge, Matt; Gupta, Nautasha; Watts, Ben; Chadik, Paul A; Ferraro, Christopher; Townsend, Timothy G

2018-02-01

Concrete grinding residue is the waste product resulting from the grinding, cutting, and resurfacing of concrete pavement. Potential beneficial applications for concrete grinding residue include use as a soil amendment and as a construction material, including as an additive to Portland cement concrete. Concrete grinding residue exhibits a high pH, and though not hazardous, it is sufficiently elevated that precautions need to be taken around aquatic ecosystems. Best management practices and state regulations focus on reducing the impact on such aquatic environment. Heavy metals are present in concrete grinding residue, but concentrations are of the same magnitude as typically recycled concrete residuals. The chemical composition of concrete grinding residue makes it a useful product for some soil amendment purposes at appropriate land application rates. The presence of unreacted concrete in concrete grinding residue was examined for potential use as partial replacement of cement in new concrete. Testing of Florida concrete grinding residue revealed no dramatic reactivity or improvement in mortar strength.

Growth and Productivity of Response of Hybrid Rice to Application of Animal Manures, Plant Residues and Phosphorus

Directory of Open Access Journals (Sweden)

Dr. Amanullah

2016-10-01

Full Text Available The objective of this research was to evaluate the impact of organic sources (animal manures vs. plant residues at the rate of 10 t ha-1 each on the productivity profitability of small land rice (Oryza sativa L. grower under different levels of phosphorus (0, 30, 60 and 90 kg P ha-1 fertilization. Two separate field experiments were conducted. In experiment (1, impact of three animal manures sources (cattle, sheep & poultry manures and P levels was studied along with one control plot (no animal manure and P applied as check was investigated. In experiment (2, three plant residues sources (peach leaves, garlic residues & wheat straw and P levels was studied along with one control plot (no plant residues and P applied as check. Both the experiments were carried out on small land farmer field at District Swabi, Khyber Pakhtunkhwa Province (Northwest Pakistan during summer 2015. The results revealed that in both experiments the control plot had significantly (p≤0.05 less productivity than the average of all treated plots with organic sources and P level. The increase in P levels in both experiments (animal manure vs. plant residues had resulted in higher rice productivity (90 = 60 > 30 > 0 kg P ha-1. In the experiment under animal manures, application of poultry manure increased rice productivity as compared with sheep and cattle manures (poultry > sheep > cattle manures. In the experiment under plant residues, application of peach leaves or garlic resides had higher rice productivity over wheat straw (peach leaves = garlic residues > wheat straw. On the average, the rice grown under animal manures produced about 20% higher grain yield than the rice grown under crop residues. We concluded from this study that application of 90 kg P ha-1 along with combined application of animal manures especially poultry manure could increase rice productivity. We conclude from this study that application of 90 kg P ha-1 along with combined application of animal

Characterization of ferric arsenate-sulfate compounds: Implications for arsenic control in refractory gold processing residues

Czech Academy of Sciences Publication Activity Database

Paktunc, D.; Majzlan, J.; Palatinus, Lukáš; Dutrizac, J.; Klementová, Mariana; Poirier, G.

2013-01-01

Roč. 98, č. 4 (2013), s. 554-565 ISSN 0003-004X Institutional support: RVO:68378271 Keywords : arsenic * ferric arsenate sulfate * autoclave residue * hydrometallurgy Subject RIV: DB - Geology ; Mineralogy Impact factor: 2.059, year: 2013

Forecasting the effects of fertility control on overabundant ungulates: White-tailed deer in the National Capital Region

Science.gov (United States)

Raiho, Ann M.; Hooten, Mevin B.; Bates, Scott; Hobbs, N. Thompson

2015-01-01

Overabundant populations of ungulates have caused environmental degradation and loss of biological diversity in ecosystems throughout the world. Culling or regulated harvest is often used to control overabundant species. These methods are difficult to implement in national parks, other types of conservation reserves, or in residential areas where public hunting may be forbidden by policy. As a result, fertility control has been recommended as a non-lethal alternative for regulating ungulate populations. We evaluate this alternative using white-tailed deer in national parks in the vicinity of Washington, D.C., USA as a model system. Managers seek to reduce densities of white-tailed deer from the current average (50 deer per km2) to decrease harm to native plant communities caused by deer. We present a Bayesian hierarchical model using 13 years of population estimates from 8 national parks in the National Capital Region Network. We offer a novel way to evaluate management actions relative to goals using short term forecasts. Our approach confirms past analyses that fertility control is incapable of rapidly reducing deer abundance. Fertility control can be combined with culling to maintain a population below carrying capacity with a high probability of success. This gives managers confronted with problematic overabundance a framework for implementing management actions with a realistic assessment of uncertainty.

Residual symptoms and functioning in depression, does the type of residual symptom matter? A post-hoc analysis

Directory of Open Access Journals (Sweden)

Romera Irene

2013-02-01

Full Text Available Abstract Background The degrees to which residual symptoms in major depressive disorder (MDD adversely affect patient functioning is not known. This post-hoc analysis explored the association between different residual symptoms and patient functioning. Methods Patients with MDD who responded (≥50% on the 17-item Hamilton Rating Scale for Depression; HAMD-17 after 3 months of treatment (624/930 were included. Residual core mood-symptoms (HAMD-17 core symptom subscale ≥1, residual insomnia-symptoms (HAMD-17 sleep subscale ≥1, residual anxiety-symptoms (HAMD-17-anxiety subscale ≥1, residual somatic-symptoms (HAMD-17 Item 13 ≥1, pain (Visual Analogue Scale ≥30, and functioning were assessed after 3 months treatment. A stepwise logistic regression model with normal functioning (Social and Occupational Functioning Assessment Scale ≥80 as the dependent variable was used. Results After 3 months, 59.5% of patients (371/624 achieved normal functioning and 66.0% (412/624 were in remission. Residual symptom prevalence was: core mood symptoms 72%; insomnia 63%; anxiety 78%; and somatic symptoms 41%. Pain reported in 18%. Factors associated with normal functioning were absence of core mood symptoms (odds ratio [OR] 8.7; 95% confidence interval [CI], 4.6–16.7, absence of insomnia symptoms (OR 1.8; 95% CI, 1.2–2.7, episode length (4–24 weeks vs. ≥24 weeks [OR 2.0; 95% CI, 1.1–3.6] and better baseline functioning (OR 1.0; 95% CI, 1.0–1.1. A significant interaction between residual anxiety symptoms and pain was found (p = 0.0080. Conclusions Different residual symptoms are associated to different degrees with patient functioning. To achieve normal functioning, specific residual symptoms domains might be targeted for treatment.

Nitrogen availability of biogas residues

Energy Technology Data Exchange (ETDEWEB)

El-Sayed Fouda, Sara

2011-09-07

The objectives of this study were to characterize biogas residues either unseparated or separated into a liquid and a solid phase from the fermentation of different substrates with respect to their N and C content. In addition, short and long term effects of the application of these biogas residues on the N availability and N utilization by ryegrass was investigated. It is concluded that unseparated or liquid separated biogas residues provide N at least corresponding to their ammonium content and that after the first fertilizer application the C{sub org}:N{sub org} ratio of the biogas residues was a crucial factor for the N availability. After long term application, the organic N accumulated in the soil leads to an increased release of N.

Health Risk Assessment of Pesticide Residues via Dietary Intake of Market Vegetables from Dhaka, Bangladesh

Directory of Open Access Journals (Sweden)

Md. Shakhaoat Hossain

2013-02-01

Full Text Available The present study was designed to assess the health risk of pesticide residues via dietary intake of vegetables collected from four top agro-based markets of Dhaka, Bangladesh. High performance liquid chromatography with a photo diode array detector (HPLC-PDA was used to determine six organophosphorus (chlorpyrifos, fenitrothion, parathion, ethion, acephate, fenthion, two carbamate (carbaryl and carbofuran and one pyrethroid (cypermethrin pesticide residues in twelve samples of three common vegetables (tomato, lady’s finger and brinjal. Pesticide residues ranged from below detectable limit (<0.01 to 0.36 mg/kg. Acephate, chlorpyrifos, ethion, carbaryl and cypermethrin were detected in only one sample, while co-occurrence occurred twice for fenitrothion and parathion. Apart from chlorpyrifos in tomato and cypermethrin in brinjal, all pesticide residues exceeded the maximum residue limit (MRL. Hazard risk index (HRI for ethion (10.12 and carbaryl (1.09 was found in lady’s finger and tomato, respectively. Rest of the pesticide residues were classified as not a health risk. A continuous monitoring and strict regulation should be enforced regarding control of pesticide residues in vegetables and other food commodities.

Thermal treatment of solid residues from WtE units: A review

International Nuclear Information System (INIS)

Lindberg, Daniel; Molin, Camilla; Hupa, Mikko

2015-01-01

Highlights: • We review the thermal treatment methods for ashes and residues from WtE plants. • We review the results from extensive laboratory work on vitrification, melting and vaporization of ash. • We analyze the results from the extensive patent literature on thermal treatment. • We review industrial concepts for thermal treatment of ash. - Abstract: Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field

Thermal treatment of solid residues from WtE units: A review

Energy Technology Data Exchange (ETDEWEB)

Lindberg, Daniel, E-mail: daniel.lindberg@abo.fi; Molin, Camilla, E-mail: camilla.molin@abo.fi; Hupa, Mikko, E-mail: mikko.hupa@abo.fi

2015-03-15

Highlights: • We review the thermal treatment methods for ashes and residues from WtE plants. • We review the results from extensive laboratory work on vitrification, melting and vaporization of ash. • We analyze the results from the extensive patent literature on thermal treatment. • We review industrial concepts for thermal treatment of ash. - Abstract: Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field.

Fate of kelthane residues on apple pomace exposed to drying in the dark, sunlight, and ultraviolet light irradiation

International Nuclear Information System (INIS)

Archer, T.E.; Toscano, R.A.

1972-01-01

The present investigations were undertaken to determine the fate of Kelthane residues intentionally applied to apples under controlled laboratory conditions and the reduction of these residues in the pomace by exposure to drying in the dark, in sunlight, and ultraviolet light irradiation

Minimization of zirconium chlorinator residues

International Nuclear Information System (INIS)

Green, G.K.; Harbuck, D.D.

1995-01-01

Zirconium chlorinator residues contain an array of rare earths, scandium, unreacted coke, and radioactive thorium and radium. Because of the radioactivity, the residues must be disposed in special waste containment facilities. As these sites become more congested, and with stricter environmental regulations, disposal of large volumes of wastes may become more difficult. To reduce the mass of disposed material, the US Bureau of Mines (USBM) developed technology to recover rare earths, thorium and radium, and unreacted coke from these residues. This technology employs an HCl leach to solubilize over 99% of the scandium and thorium, and over 90% of the rare earths. The leach liquor is processed through several solvent extraction stages to selectively recover scandium, thorium, and rare earths. The leach residue is further leached with an organic acid to solubilize radium, thus allowing unreacted coke to be recycled to the chlorinator. The thorium and radium waste products, which comprise only 2.1% of the original residue mass, can then be sent to the radioactive waste facility