WorldWideScience

Sample records for nado kaihatsu shinbu

  1. Development of hot water utilizing power plants in fiscal 1999. Development of technology to collect geothermal resources in great depths/Development of technology to excavate geothermal resources in great depths (Designing whole development); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen kussaku gijutsu no kaihatsu (zentai kaihatsu sekkei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Technological development has been made on excavation of geothermal wells, which are dense, hard, and high in temperature and pressure, in developing geothermal resources in great depths. This paper summarizes the achievements in fiscal 1999. This fiscal year has performed the excavation test using an actual well to verify the reliability in practical use of the developed heat-resistant and durable bit. The test was executed by using a bit with a diameter of 8-1/2 inches in a ground bet having a maximum temperature of 300 degrees C in the Yamakawa geothermal field. As a result, good site evaluation was obtained that the wear and tear after lift-up showed no problems, and sufficient performance was verified in the drilling rate and durability. In addition, the low specific gravity cement for high temperature use that has been newly developed was given a cement mixing test to identify its workability at site and hardening properties, at a test well with a temperature of about 40 degrees C in the Okiri geothermal field. The actual well test was performed in a large-scale lost water occurred in a return well during an excavation by Nittestu-Kagoshima Geothermal Company. Effects were recognized in measures to prevent water loss. (NEDO)

  2. Development of hot water utilizing power plants in fiscal 1999. Development of technology to collect geothermal resources in great depths (Development of technology to produce geothermal resources in great depths); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to develop geothermal resources, research and development has been performed on the production technologies for the deep-seated geothermal resources, such as pressure, temperature, flow speed and density (PTSD) logging technologies. This paper summarizes the achievements in fiscal 1999. In the actual well test on the developed D-probe, it was verified that the probe operates normally under high temperature environment (342 degrees C) which exceeds the measurement limit of conductive cables (315 degrees C). In developing the PTC monitoring technology, the downhole sampler was improved, and a test was performed in the actual hole in the Hijiori area in Yamagata Prefecture. As a result, collection of hot water of about 900 mL has become possible. In developing the high-temperature tracer monitoring technology, simulation was performed keeping in mind charging the tracer into the Hijiori geothermal area, whereas specifications for charging and collecting the tracer were determined. In developing the scale monitoring technology, experiments were carried out on the fluid systems under deep geothermal conditions by using scale forming devices, by which it was indicated that silica is the important scale constituent. (NEDO)

  3. FY 1998 report on the project for development of hot water utilizing power generating plants and others, supported by New Sunshine Project. Development of extraction technologies and development of production technologies for the deep-seated geothermal resources; 1998 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Described herein are the FY 1998 results of the activities for development of extraction and production technologies for the deep-seated geothermal resources, which are expected to contribute to increased geothermal power generation capacity. The program for the PTSD logging technology connects the S probe to PT probe, to simultaneously measure temperature, pressure and volumetric flow, producing the data of good quality even in a high temperature environment over 327 degrees C. Thus, possibility of the commercial system is confirmed. The D probe also produces a density calibration curve showing very good linearity, and operates normally in a high temperature environment of 406 degrees C. The program for the PTC monitoring technology conducts the field tests at Larderello, Italy, to confirm the sampler functions in a high temperature environment. The program for the tracer monitoring technology extracts promising tracers stable at high temperature from those for the liquid, vapor and liquid/vapor mixed phases. Silica is observed to be massively dissolved at 400 to 1,000mg/kg in the fluid under deep geothermal conditions. Scale precipitation rate is minimal for the first 21 days, but increases linearly with time thereafter. The experiments are also conducted for formation and prevention of the Fe-Si-based scales during the flushing period. (NEDO)

  4. Report on New Sunshine Program-supported undertakings for fiscal 1995. Development of hot water power plant and deep-seated geothermal resources sampling/exploiting technologies; 1995 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu, shinbu chinetsu shigen seisan gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Reported are the results of researches conducted in fiscal 1995. For the formulation of a general development design, data are collected about domestic high-temperature thermal wells through questionnaires and literature probing, and are scrutinized. As for the development of logging technology, a memory type PT (Pressure, Temperature) logger is experimentally constructed, and is found to properly operate in an environment of up to 350degC in a production well. An experimentally manufactured S-probe proves to be capable of heat insulation and sealing. In the field of PT monitoring, a high-temperature optical fiber is experimentally fabricated for study, capable of measuring temperatures up to 400degC. As for the development of high-temperature tracer monitoring technology, basic experiments are conducted about the thermal characteristics of aromatic acids, and preparatory experiments about gas phase tracers. In the study of scale monitoring technology, deep-seated fluids are collected and analyzed. In the field of production control, technical problems are discussed and information is gathered centering on methods for scale prevention and removal. 31 refs., 90 figs., 40 tabs.

  5. Report on New Sunshine Program-supported undertakings for fiscal 1997. Development of hot water power plant and deep-seated geothermal resources sampling/exploiting technologies; 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu, shinbu chinetsu shigen saishu gijutsu no kaihatsu, shinbu chinetsu shigen seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Reported are the results of researches conducted in fiscal 1997. In the field of PTSD (Pressure, Temperature, Spinner flowmeter, fluid Density) well logging, the high-temperature performance of a memory type PT (Pressure, Temperature) well logger is confirmed in a demonstration test. As for the S-probe, modification is effected for the reduction of the outside diameter from 70mm to 56mm, and tests are conducted in real wells. As for the D-probe, a laboratory test is conducted and then the probe behaves as predicted. In the field of PCT (Pressure, Chemical, Temperature) monitoring, the sampler is subjected to an on-site test in Italy, when water is successfully sampled out of the well. In the field of scale monitoring technique, deep-seated fluid is collected and examined, and the scale deposition rate in the deep-seated fluid is determine. For the study of production control technology with respect to scale prevention and removal, an Mg-Si scale synthesis test is conducted in the temperature range of 100-300degC, and it is found that the solubility of scale decreases with a rise in temperature. 19 refs., 93 figs., 24 tabs.

  6. Achievement report for fiscal 1998 on business auxiliary to New Sunshine Program. Hot water-aided power generation plant development (Development of deep-seated geothermal resources exploitation technology and development of deep-seated geothermal resources excavating technology); 1998 nendo new sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu, shinbu chinetsu shigen kussaku gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the general exploitation scheme, technological information is collected about cement overseas, DHM (down hole motor), etc. In the development of heat-resistant durable bits, an improved version of the 350 degrees C real bit manufactured in fiscal 1997 undergoes a test in a real bore, and is evaluated for its general performance. In the development of high-temperature cement slurries, the ultralow specific gravity cement slurry for casing cement developed in fiscal 1997 is subjected to evaluation. It is examined by chemical analysis and powder X-ray diffraction, and its fluidity, free water, rate of dehydration, and compression strength at 250 degrees C are measured. In a real bore test, a slurry of the optimum composition is prepared and then hardened, and the hardened body is kept exposed to geothermal environments for eight weeks. It is then found that the hardened body retains a compression strength of 70kgf/cm{sup 2}. In the development of a down hole motor, a scale model, real in diameter and shortened in length, is built of the motor section, and is tested in circulating water and oil at normal and high temperatures, and its behavior and performance are evaluated. (NEDO)

  7. Fiscal 1996 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the deep geothermal resource collecting technology (development of the deep geothermal resource producing technology); 1996 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen seisan gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper reported the results of the fiscal 1996 R and D of the deep geothermal resource collecting/producing technology. In the design of the total development, characteristics of the well mouth of the deep reservoir were examined to evaluate properties of deep geothermal resource, and the necessity of the pressure design, etc. were clarified. As to PTSD logging technology, conducted were improvement of PT probe, manufacture of a sonde of which S probe was integrated with memory/battery modules, and the actual well experiment. Concerning PTC monitoring technology, an experiment was carried out on a high temperature use optical fiber GI type, and it was shown that the type was on a commercial level. Further, a prototype sampler with 300degC heat resistance was trially manufactured, and a test to confirm its work was conducted in the well in the Corn Wall area of the U.K. As to the production control technology, studied was the arrangement of the production control technology for deep geothermal resource. Moreover, an experiment was made to examine the effect of metal ions coexisting when silica in the deep fluid precipitates. 46 refs., 107 figs., 38 tabs.

  8. Fiscal 1995 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the deep geothermal resource collecting technology (development of the deep geothermal resource drilling technology); 1995 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen kussaku gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper reported the results of the fiscal 1995 R and D on the development of deep geothermal resource collecting/drilling technology. In the design of a total development, the trend of technical development was examined of bits, cement and DHM overseas. Further, the simulational prediction was conducted in deep geothermal drilling. As to the development of element technology of hard high temperature strata drilling, the R and D of seal mechanism, bearing mechanism and cutter mechanism were carried out aiming at developing heat resistant/durable bits, and a bit was trially manufactured which was integrated with element parts selected by each element technology. Concerning the development of high temperature drilling mud, studies were made of the development of drilling mud materials, a mud system, etc. Relating to the development of high temperature cement slurry, the development was conducted of high temperature cement, dewatering adjusting agents, etc. As to the development of high accuracy much inclination drilling technology, in the development of high temperature use downhole motor, tests on heat resistance/durability were carried out in the mud of 12 kinds of high heat resistant stator materials. 175 figs., 137 tabs.

  9. Fiscal 1996 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the deep geothermal resource collecting technology (development of the deep geothermal resource drilling technology); 1996 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen kussaku gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper reported the results of the fiscal 1996 R and D on the development of deep geothermal resource collecting/drilling technology. In the design of a total development, the planned adjustment of actual well tests was conducted on bits and drilling mud at the time of drilling the exploration well of the Kakkonda area. As to the trend of overseas technology, examined was the developmental trend of high temperature type downhole motor products. In the development of hard high temperature strata drilling element technology, a drilling test was carried out on trially manufactured 300degC heat resistant/durable bits. In the development of high temperature drilling mud, drilling was done in the mud of thermally stable quality in the actual well experiment using the 300degC mud system. In the development of high temperature use cement and high temperature use cement slurry, a possibility was obtained of composing a slurry which has the targeted dewatering amount, compressive strength, and water permeability. In the development of high temperature downhole motor, data on characteristics of heat resistant stator materials were arranged in a relationship among the abrasion amount, thermal expansion amount and elastic recovery amount, and the database was obtained. 166 figs., 148 tabs.

  10. Industry brief letter; Kasupikaioki sekiyu koku kaihatsu sekiyu shigen kaihatsu nado sannyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    4 companies of Petroleum Resources Development, Indonesia Petroleum, Teikoku Petroleum an Itochu Petroleum Development will sign petroleum exploration and development contract in petroleum mining property offshore of Caspian Sea with Azerbaijan National Petroleum Company, Sokar Company. In another mining property, Mitsui group reached conclusion with Sokar Company in mining right. Resource development competition between existing international petroleum majors and Japanese petroleum companies around Caspian Sea may be further intensified. (translated by NEDO)

  11. Development of production technology for deep-seated geothermal resources; Shinbu chinetsu shigen seisan gijutsu no kaihatsu gaiyo

    Energy Technology Data Exchange (ETDEWEB)

    Wada, T.; Akazawa, T. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1997-11-01

    In order to increase the geothermal power generation volume in Japan furthermore after now, it is necessary to develop the deep-seated geothermal fluid collecting technique at 3,000 to 4,000m in depth and about 350degC. In order to collect the deep-seated geothermal resources economically and effectively, there are some principally important problems on production techniques such as P (pressure)-T(temperature)-S (flow rate)-D (fluid density) logging technique, P (pressure)-T (temperature)-C (chemical composition) monitoring technique, high temperature tracer monitoring technique, scale monitoring technique, scale protection and removal technique and so on. The PTSD logging technique is a measuring technique for collecting some data necessary to conduct production management effectively. The PTC monitoring technique is a technique for collecting data on the geothermal resources essential for the resources evaluation and presumption, and tracer monitoring technique is a technique for collecting actual measurement data of fluid flow analysis in the deep-seated geothermal resources. And the sale monitoring is a technique for collecting data on various kinds of scale components of the deep-seated geothermal water and in the steam. In this paper, these techniques are summarized. 8 figs.

  12. Fiscal 1995 verification survey of geothermal exploration technology. Report on a deep geothermal resource survey; 1995 nendo chinetsu tansa gijutsu nado kensho chosa. Shinbu chinetsu shigen hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    For the purpose of reducing the risk of deep geothermal resource development, the paper investigated three factors for the formation of geothermal resource in the deep underground, that is, heat supply from heat source, supply of geothermal fluids, and the developmental status of fracture systems forming reservoir structures. The survey further clarified the status of existence of deep geothermal resource and the whole image of the geothermal system including shallow geothermal energy in order to research/study usability of deep geothermal resource. In the deep geothermal resource survey, drilling/examination were made of a deep geothermal exploration well (`WD-1,` target depth: approximately 3,000-4,000m) in the already developed area, with the aim of making rationalized promotion of the geothermal development. And the status of existence of deep geothermal resource and the whole image of the geothermal system were clarified to investigate/study usability of the geothermal system. In fiscal 1995, `WD-1` in the Kakkonda area reached a depth of 3,729m. By this, surveys were made to grasp the whole image of the shallow-deep geothermal system and to obtain basic data for researching usability of deep geothermal resource. 22 refs., 531 figs., 136 tabs.

  13. FY 2001 report on the results of the development of the hydrothermal utilization power plant, etc. Development of collecting technology for deep geothermal resources (Development of drilling technology for deep geothermal resources); 1992 - 2001 nessui riyo hatsuden plant tou kaihatsu sokatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu - Shinbu chinetsu shigen kussaku gijutsu no kaihatsu (2001 nendo seika hokokusho bessatsu shiryo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the purpose of developing deep geothermal resources, development of 'drilling technology of deep geothermal resources' was made from FY 1991 to FY 2001, and the results were summarized. As to the development of bits, the bit that can be used for 30 hours or more at a temperature of 250 degrees C was developed, and the demonstrative test was made in FY 1997. Relating to the development of the high temperature use drilling mud, the mud that can be used at a temperature of 350 degrees C was developed, and the test using the actual well was conducted in FY 1997. Concerning the development of the high temperature use cement slurry, the cement slurry with specific gravity of 1.35 or below that can be used under the environment of a temperature of 350 degrees C was developed, and the hanging test of the specimen was made in the actual well in FY 1998. About the development of the high temperature use downhole motor, a prototype of 1/12 scale was fabricated in FY 1998, and the performance test at high temperature was conducted. As to the development of the high temperature use high strength cement slurry, a cement slurry with specific gravity of 1.50 or below and compressive strength of 19.61 MPa that is used under the environment of a temperature of 300 degrees C was developed, and the test on the long-term compressive strength was made in FY 2001. (NEDO)

  14. Results of the supplementary work to the fiscal 1994 New Sunshine Project. Development of geothermal power plants, etc. (development of production, technology for deep-seated geothermal resources); 1994 nendo new sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant to kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu shinbu chinetsu shigen seisan gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The paper reports on the fiscal 1994 results of the study of the development of a technology for collecting deep-seated geothermal resources, which has been made for increasing the capacity of the geothermal power generation as a part of the New Sunshine Project. As a plan for the development, a development is made of logging equipment and its auxiliary system and then characteristics of the deep-seated geothermal well are clarified. The logging equipment is a PTSD (pressure/temperature/spinner flow-meter/fluid density) logger which stands the use at deep-seated geothermal wells of 400{degree}C and 490 kgf/cm{sup 2} and measures pressure, temperature, flow rate and fluid density under static and dynamic conditions. In this fiscal year, metal seals were developed for preventing geothermal fluids from penetrating into the PT probe. Qualities and inner/outer diameters of various kinds of structural materials used in the S probe were determined, and output necessary enough to detect the rotation number is obtained. Measuring precision of D logging by {gamma} rays was evaluated. The study was made of the monitoring technology including the borehole and ground measuring system, the borehole fluid sampling and the scale formation. Relating to the tracer widely used in monitoring of hydrothermal reservoirs, investigated was the trend of the technology from abroad. 8 refs., 60 figs., 26 tabs.

  15. FY 2001 report on the results of the development of the hydrothermal utilization power plant, etc. Development of collecting technology for deep geothermal resources (Development of production technology for deep geothermal resources); 1992 - 2001 nessui riyo hatsuden plant tou kaihatsu sokatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu - Shinbu chinetsu shigen seisan gijutsu no kaihatsu (2001 nendo seika hokokusho bessatsu shiryo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For making effective/economical collection of deep geothermal resources, development was made from FY 1991 to FY 2001 of the 'drilling technology for deep geothermal resources' and 'production technology for deep geothermal resources,' and the results were summarized. As to the development of logging technology, the PTSD logging system was developed which can measure temperature/pressure/flow velocity/fluid density in geothermal well under the environment of temperature of 400 degrees C. Concerning the development of monitoring technology, development was made of the PT monitoring system that can make the long-term continuous measuring of temperature/pressure in deep geothermal observation well under the environment of temperature of 400 degrees C and of the C monitoring system that samples geothermal fluids at regular intervals to grasp changes in chemical component. Relating to the development of high temperature tracer monitoring technology, the following were conducted: extraction of high temperature tracer agent that can be used in geothermal reservoirs under the environment of temperature of 300 degrees C, development of simulator, and establishment of how to put tracer agent into the reservoir and how to analyze tracer agent. Further, the R and D were made of scale monitoring technology and scale prevention/removal technology. (NEDO)

  16. Achievement report for fiscal 2000 on New Sunshine Project aiding program. Development of hot water utilizing power generation plant (Development of deep seated geothermal resource collection technologies - development of deep seated geothermal resource production technologies); 2000 nendo nessui riyo hatsuden plant to kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu (Shinbu chinetsu shigen seisan gijutu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Items of information about deep seated geothermal resource production technologies were collected, and tests and studies were performed using actual wells. This paper summarizes the achievements in fiscal 2000. In developing the PTDS logging technology, it was verified in the actual well tests that the measured density of a D probe is consistent with the theoretical density, and the accuracy is satisfactory. The extended time measurement at fixed points on temperatures of fluids in the wells, pressures, flow rates, and fluid densities has identified chronological change of the characteristics of the fluids in the wells, including the enthalpy, proving them to be effective in well control. In developing the PTC monitoring technology, a fluid extracting machine for the downhole fluid sampler was fabricated, which has collected hot water successfully in the actual well twice out of seven attempts. In developing the high temperature tracer monitoring technology, experiments were performed using vapor phase and liquid phase tracers, whereas re-discharge of all the tracer materials was identified. In developing the scale preventing and removing technology, a silica recovering device capable of treating hot water at 0.6 ton per hour as maximum was fabricated, and the site tests were performed by using cation-based coagulant. (NEDO)

  17. Confirmation study of the effectiveness of prospect techniques for deep geothermal resources. Deep-seated geothermal resources survey report (Fiscal year 1993); 1993 nendo chinetsu tansa gijutsu nado kensho chosa. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Drilling and survey of deep geothermal exploration wells were conducted in order to grasp the existing situation of deep geothermal resource and the whole image of geothermal systems in the area where geothermal resource was already developed. Following fiscal 1992, the well was drilled in fiscal 1993 down to depths of 605m-1505m, and a 13-3/8 inch casing was inserted down to a depth of 1500m. In the drilling, four cores including oriented cores were sampled, and microscopic observation, X-ray diffraction analysis, fluid inclusion survey, core property test, etc. were conducted. In the FMI logging, detected were 273 bedding planes, 483 fractures, etc. Further made were a velocity structure survey, a gravity survey in the area of 270 km{sup 2} including deep exploration wells, a quality survey of the Kakkonda river water, etc. As to geothermal structure models in the Kakkonda area, results of the drilling were added to prediction models before drilling deep exploration wells, but the revision was not very much. Besides, studies were made of a survey method using microearthquakes, a survey technique using resistivity, etc. 61 refs., 259 figs., 95 tabs.

  18. FY 1998 report on the verification survey of geothermal exploration technology, etc. 1/2. Survey of deep geothermal resource; 1998 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 1/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    For the purpose of commercializing deep geothermal resource, a deep exploration well of 4000m class was drilled in the existing geothermal development area to survey the situation of deep geothermal resource existence and the availability. Concretely, the deep geothermal exploration well was drilled for study in the Kakkonda area, Shizukuishi town, Iwate prefecture, to clarify the situation of deep geothermal resource existence and the whole image of geothermal system. Consideration was made of the deep geothermal exploration method, systematization of deep high temperature drilling technology, and availability of deep geothermal resource. The results of the survey were summed up as follows: 1) general remarks; 2) deep exploration well drilling work; 3) details of the study. 1) and 2) were included in this report, and 3) in the next report. In 1), the items were as follows: the study plan/gist of study execution, the details and results of the deep geothermal resource survey, the outline of the deep exploration well drilling work, and the outline of the results of the FY 1998 study. In 2), the drilling work plan/the actual results of the drilling work were summed up. As to the results of the study, summarized were the acquisition of survey data on deep exploration well, heightening of accuracy of the deep geothermal resource exploration method, etc. (NEDO)

  19. Report on fiscal 1999 survey for geothermal exploration technology verification. Survey of deep-seated geothermal resources; 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    To promote the development of deep-seated geothermal resources in a rationalized way, studies were conducted about deep-seated geothermal resource assessment techniques, development guidelines, and the like. For the development of techniques for estimating deep-seated geothermal reservoir parameters, the Uenotai district, Akita Prefecture, and the Hatchobaru district, Oita Prefecture, were designated as model fields, and a geothermal system conceptual model was fabricated. Data of the two districts were registered in a database. Using these data, verification was performed of the validity of stochastic estimation techniques, large area flow simulation, rock/water equilibrium reaction simulation, and the like. As for the technique of deep-seated resource amount estimation, a simplified reservoir model was experimentally constructed based on parameters determined by the stochastic estimation of deep-seated reservoirs and on the conceptual model, and a method was studied for TOUGH2-based production prediction. Studies were also made about deep-seated geothermal resource development guidelines, such as exploration guidelines, exploration well boring guidelines, and geothermal fluid production guidelines. (NEDO)

  20. Fiscal 1997 verification and survey of geothermal prospecting technology etc. 2/2. Survey report on deep-seated geothermal resources; 1997 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 2/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In the evaluation and study of reservoirs and the amount of resources, a reservoir simulation is conducted to grasp the characteristics of reservoirs and the amount of resources. For this purpose, the origin and history of the Kakkonda geothermal field are studied, with special attention paid to the origin of the difference in temperature between the shallow-seated and deep-seated reservoirs, the geometry of granite at Kakkonda, the region of recharge of meteoric water, the distribution of saline concentration in the natural state and the cause of the occurrence, the amount of supply of fluids and heat from the depth to the reservoirs, etc. In the evaluation and study of the economic effectiveness of the exploitation of deep-seated geothermal resources, it is learned that, if a 50MW geothermal power station is to be built at a deep level (drilled depth of 3000m on the average) with a rate of 50% attained in drilling, the steam amount required at such a deep level (presumed to be 75t/h) will be more than twice that required at a shallow level (presumed to be 35/h). (NEDO)

  1. Fiscal 1997 verification and survey of geothermal prospecting technology etc. 1/2. Survey report on deep-seated geothermal resources; 1997 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 1/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In fiscal 1997, a fumarolic gas test is conducted at the deep-seated geothermal well WD-1b which was drilled in the preceding fiscal year. In the test, chemical and isotopic characteristics are compared between the fluids of the WD-1b and the other existing deep-seated wells, and it is found that the fluids from the WD1b originates in surface water just like the fluids from the others and that the constitution of its gas is not greatly affected by magmatic fluids. A PTS (Pressure, Temperature, Spinner flowmeter) logging is performed to observe conditions in the well with the fluids being discharged and to know the inflow point and rate the fumarolic fluids, and the result is utilized to presume the 3-dimensional stress in the vicinity of the WD-1. An isotopic measurement of water included in the fluids is conducted to examine the origin of the geothermal fluids, constant observation and analysis of micro-earthquakes are carried out, and the fluid flow and fluid hydraulic characteristics are also studied. (NEDO)

  2. FY 1998 report on the verification survey of geothermal exploration technology, etc. 2/2. Survey of deep geothermal resource; 1998 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 2/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    For the purpose of commercializing deep geothermal resource, a deep exploration well of 4000m class was drilled in the existing geothermal development area to survey the situation of deep geothermal resource existence and the availability. Concretely, the deep geothermal exploration well was drilled for study in the Kakkonda area, Shizukuishi town, Iwate prefecture, to clarify the situation of deep geothermal resource existence and the whole image of geothermal system. Consideration was made of the deep geothermal exploration method, systematization of deep high temperature drilling technology, and availability of deep geothermal resource. The results of the survey were summed up as follows: 1) general remarks; 2) deep exploration well drilling work; 3) details of the study. This report contained 3). In 3), the items were as follows: heightening of accuracy of the deep geothermal resource exploration method, making of a geothermal model in the Kakkonda area, study of deep drilling technology, study of deep fluid utilization technology, and making of a guide for deep geothermal resource exploration/development in the Kakkonda area. As to the technology of high temperature deep geothermal well drilling, studies were made of the borehole cooling method, mud water cooling method, survey of deterioration of casing with age, etc. (NEDO)

  3. Report on fiscal 2000 survey for geothermal exploration technology verification. Survey of deep-seated geothermal resources; 2000 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    To promote the development of deep-seated geothermal resources in a rationalized way, studies are conducted about deep-seated geothermal resource assessment techniques, development guidelines, and the like. Data were collected at the Sumikawa-Onuma district, Ogiri district, Mori district, Yanaizu-Nishiyama district, and the Onikobe district, and compiled into a database to be open to the public. Studies were made about methods for estimating parameters for deep-seated geothermal reservoirs. The resultant findings indicate that, in the Uenotai and Sumikawa-Onuma districts where geothermal reservoirs are governed mainly by a fracture network, the relaxation method and extrapolation will be effective for deep-seated reservoir temperature estimation, and the ascending current analysis method and extrapolation for permeability estimation. The findings also indicate that the expanse of deep-seated reservoirs will be suitably estimated using a method similar to that applied to shallow-seated reservoirs. In the study of the estimation of the amount of deep-seated geothermal resources, it is concluded that the simplified model A will be effective in dealing with a geothermal district where there is a well-developed fracture network and the simplified model B in dealing with a geothermal district where supply of deep-seated fluid governed by an extensive fault prevails. (NEDO)

  4. Fiscal 1996 verification and survey of geothermal prospecting technology etc. 1/2. Survey report on deep-seated geothermal resources; 1996 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 1/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In fiscal 1996, the deep-seated exploration well WD-1a is sidetracked for penetration for a target newly assigned at the 3,000m-deep level. Carried out in a survey of well geology are the naked-eye and microscopic observation of core cuttings, X-ray powder method, examination of inclusions in fluids, chemical analysis of whole rocks, analysis of isotopes in minerals, analysis of core fracturing, etc. Also, data are collected from a survey of mud log, survey of water in the well before digging, and from well logging. Furthermore, pressure monitoring etc. are conducted in order to determine the interference in pressure between the deep-seated and shallow-seated wells that accompanies multiple outbursts from the Kakkonda No. 2 machine, to know the water permeability between the shallow-seated and deep-seated parts, and to grasp the anisotropy in permeability in shallow-seated reservoirs. (NEDO)

  5. Confirmation study of the effectiveness of prospect techniques for geothermal resources. Deep-seated geothermal resources survey report (Fiscal year 1994); 1994 nendo chinetsu tansa gijutsu nado kensho chosa. Shinbu chinetsu shigen chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Drilling and survey of deep geothermal exploration wells were conducted to grasp the existing situation of deep geothermal resource and the whole image of geothermal systems in the area where geothermal resource was already developed. In the drilling work in fiscal 1994, 4000m-class rigs and the top drive system were planned to be used for drilling of 12-1/4 inch wells, but 9-5/8 inch liners were used for drilling down to depths of 2550m or deeper since the amount of lost circulation is large and the withdrawal of devices may be very difficult. And in 8-1/2 inch wells, the well was drilled down to a depth of 2950m. As to the deep resistivity exploration technology using electromagnetic method, studies were made of a multiple-frequency array induction logging (MAIL) method, a vertical electromagnetic profiling (VEMP) method, a joint analysis method, etc. Concerning the synthetic fluid inclusion logging technology, containers were lowered into the well and a comparison was made between data of the homogenization temperature analysis of the formed fluid inclusion and those of the temperature log analysis. With relation to the making of deep geothermal structural models, revision was made according to the determination of depths of Miocene formations, Pre-tertiary formations, and the Kakkonda granite. 65 refs., 268 figs., 79 tabs.

  6. Fiscal 1996 verification and survey of geothermal prospecting technology etc. 2/2. Survey report on deep-seated geothermal resources; 1996 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 2/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In the study of deep-seated geothermal models for the Kakkonda area, a reservoir structure model, a thermal structure model, and a geothermal fluid/hydraulic structure model are deliberated. Then, after studying the relations of the said three structure models to fracture systems, the boundary between the geothermal fluid convection region and the thermal conduction region near the 3,100m-deep level, the existence of high-salinity fluids and the depth of gas inflow, the ranges of shallow-seated reservoirs and deep-seated reservoirs, the trend of reduction in reservoir pressure and the anisotropy in water permeability in shallow-seated reservoirs, etc., a latest reservoir model is constructed into which all the findings obtained so far are incorporated. As for guidelines for deep-seated thermal resources survey and development, it is so decided that deep-seated geothermal survey guidelines, deep-seated fluid production guidelines, and deep-seated well drilling guidelines be prepared and that assessment be made of their economic effectiveness. (NEDO)

  7. Desempenho em 200 m nado crawl: índice de coordenação, tempo propulsivo e cinemática de nado

    Directory of Open Access Journals (Sweden)

    Marcos Franken

    2016-07-01

    Full Text Available DOI: http://dx.doi.org/10.5007/1980-0037.2016v18n3p311   O objetivo deste estudo foi comparar índice de coordenação, tempo propulsivo, duração das fases da braçada e parâmetros cinemáticos ao longo de 200 m nado crawl. Variáveis foram comparadas entre os quatro trechos de 50 m (T1 a T4 em quinze nadadores competitivos (idade: 21,1 ± 7,1 anos; estatura: 180,1 ± 6,1 cm; envergadura: 187,3 ± 8,1 cm; massa corporal: 72,1 ± 10,1 kg; melhor desempenho na prova: 77,5 ± 4,7% do recorde mundial. Obtiveram-se os dados com duas câmeras de vídeo (60 Hz - acopladas a um carrinho sobre trilhos na lateral da piscina, para imagens simultâneas do plano sagital do nadador: abaixo da linha da água e acima da linha da água. Frequência média de ciclos, comprimento de braçada (assumida como a distância média percorrida pelo corpo a cada ciclo e velocidade média de nado foram obtidos com cronometragem manual. Ao longo dos 200 m, o índice de coordenação não se alterou (p > 0,05, mas houve incremento da frequência de ciclos (p < 0,05 e redução da distância percorrida por ciclo (p < 0,05. Entre T1 e T2, houve incremento do tempo propulsivo (p < 0,05 e entre T1 e T4, da duração da fase de puxada (p < 0,05. Velocidade de nado diminuiu apenas entre T1 e T2 (p < 0,05. Ao longo de 200 m nado crawl, nadadores bem treinados incrementam tempo propulsivo, duração da fase de puxada e frequência de ciclos de braçadas, tais mudanças podem ser devidas à tentativa de manutenção da velocidade ao longo dos 200 m.

  8. Research and development of utilization technology of solar thermal system for industrial and other use. Development of passive solar system (research and development of advanced glazing); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Passive solar system no kaihatsu (chokozai nado no kenkyu kaihatsu (advanced grazing no kenkyu kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for advanced glazing in which solar energy is efficiently utilized. The peripheral techniques are surveyed for evaluation of characteristics of large-size dimming glass, optimization of film compositions and scaling up. The dimming device, made on a trial basis, attains a target controllable rage of at least 50% for visible light transmittance. The suitable components include WO3 as the electrochromic material producing color under a reducing atmosphere, NiO as the counter electrode producing color under an oxidative atmosphere, and hydrated SbOx as the proton-conducting electrolyte. The test results indicate possibility of the dimming glass stably operable while being irradiated with a quantity of sun ray of around 10 years. The study on scaling up the dimmer glass develops, on a trial basis, a process for producing large-size glass and evaluates its characteristics, where the film parameters are investigated. It also investigates the peripheral techniques for assembling the devices for the large-size glass, and develops useful techniques, such as those for sealants and improved sealing methods. 1 fig., 1 tab.

  9. Flotabilidad y similitud del nado de Manta birostris(Elasmobranchii: Myliobatidae con el ciclo de vuelo de Columba livia(Aves: Columbidae

    Directory of Open Access Journals (Sweden)

    Iván Meza Vélez

    2013-12-01

    Full Text Available Se analizó la física de la flotación en la mantarraya Manta birostrisy se comparó el nado con el ciclo de vuelo de la paloma doméstica Columba livia, con la finalidad de encontrar similitudes y diferencias en las locomociones y las leyes físicas que intervienen. Se demostró que uno de los dos ciclos de nado estudiados de esta especie posee tres de las cuatro fases principales del ciclo de vuelo de la paloma doméstica. También se demostró un “efecto paracaídas” en M. birostris, el cual le ofrece una ventaja en su locomoción. Adicionalmente, se describió cómo el concepto físico de torque se aplica al giro de esta especie.

  10. Freestyle swimming technique variations using a parachute Variaciones en la técnica de crol durante el nado resistido con paracaídas

    Directory of Open Access Journals (Sweden)

    J.M. García

    2010-09-01

    Full Text Available

    The appearance of new assistance materials like the parachute make it necessary for coaches to know about the impact that such devices have in swimming. To study this theme 16 national and international swimmers between 19 and 24 years old have been selected. The swimmers participated in four tests that consisted in freestyle (crawl stroke swimming for 10 and 45 seconds at maximum intensity, both with and without the parachute. These tests analysed stroke frequency and stroke length. A within-subjects design has been applied and a study of the facts has been made with an AVAR with repeat measures. The results indicate that the stroke frequency decreases (p<0.05 in the parachute swim during the 10 and 45 second tests, compared with the normal swim. It was also observed that the stroke frequency is higher (p<0.01 in the 10 second test than in the 45 second test. The stroke length is higher (p<0.01 in the normal swim test than in the parachute test. With respect to the swim periods of time, the stroke length is higher (p<0.01 in the 45 second test than in the 10 second test. The parachute swim produces important changes in stroke frequency and stroke length in both the 10 and 45 second tests in subjects swimming the freestyle at maximum intensity.
    KEY WORDS: swimming, swim resistance, parachute, crawl, freestyle,. stroke frequency, stroke length.

    La aparición de nuevos materiales auxiliares, como el paracaídas, hace necesario que los entrenadores conozcan las modificaciones que estos producen durante el nado. Para conseguir este objetivo se seleccionaron a 16 nadadores de nivel nacional e internacional comprendidos entre los 19 y 24 años. Éstos realizaron cuatro pruebas que consistieron en nadar a crol durante 10 y 45 segundos a máxima intensidad, utilizando el nado normal (NN y el nado resistido con paracaídas (NRCP. En estas pruebas se analizaron las variables

  11. Efeitos comportamentais e imunológicos da fluoxetina em ratos submetidos ao nado forçado

    Directory of Open Access Journals (Sweden)

    Eduardo Vignoto Fernandes

    Full Text Available No presente trabalho, os efeitos comportamentais e imunomoduladores da fluoxetina foram avaliados num modelo animal de depressão, o nado forçado. Nesse, o comportamento de flutuar é sensível a antidepressivos e é usado como índice de desespero comportamental. Foram utilizados dois grupos experimentais, sendo um grupo controle tratado com salina e outro grupo teste tratado com a fluoxetina, ambos administrados por via intra-peritoneal. Os animais foram tratados três vezes ao dia por 12 dias. Adicionalmente, a resposta imune humoral a uma imunoestimulação (hemácias de carneiro foi avaliada. A fluoxetina provocou aumento no tempo em flutuação, queda na massa corporal e menor produção total de anticorpos. Os resultados indicam uma modulação simultânea do comportamento e do sistema imunológico pela fluoxetina.

  12. Fiscal 2000 collection of manuscripts for technology development committee on hydrogen energy and the like; 2000 nendo suiso energy nado kanren gijutsu kaihatsu iinkai yokoshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-07

    The subjects listed in the collection are (1) the research and development of international clean energy system technology utilizing hydrogen (WE-NET - World Energy Network), including the outline of the project as a whole; research on system evaluation; research and development of safety measures; development of technologies for liquid hydrogen transportation and storage; research on low-temperature materials; development of hydrogen supply station and hydrogen-driven automobile system; development of supply station for hydrogen produced by electrolysis of water; development of hydrogen fuel system; development of hydrogen production technology; development of hydrogen absorbing alloys for dispersed hydrogen transportation and storage; development of polymer electrolyte fuel cell fed with pure hydrogen; and the development of power generation technology, (2) the development of closed type high-efficiency turbine technology capable of carbon dioxide recovery, and (3) the development of frontier technology of carburation using sensible heat in coke oven gas. (NEDO)

  13. Achievement report for fiscal 2000 on development of technology to evaluate reliability of petroleum refining facilities; 2000 nendo sekiyu seisei setsubi shinraisei hyoka nado gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper reports the achievements in fiscal 2000 in development of a technology to evaluate reliability of petroleum refining facilities. The development efforts were made mainly on analyses by simulation and neural net (NN) that utilize computers. In the high-temperature system facilities, the creep damage generation is governed by different factors including impurities. The evaluation on joint life requires simultaneous use of low temperature zone long-time test. Verification was made on application of non-destructive inspection, such as use of ultrasonic waves in the accelerated creep zone. Defect detecting capability was identified when an ultrasonic wave flaw detection model is used for buried piping. In the pulse eddy current flaw detection, a coil most superb in totality was selected by means of simulation, by which corrosion and wall thickness of piping and devices were detected from outside the sheathing materials. Development was made on a technology to diagnose and evaluate corrosion of tank in operation by using the AE method. The remaining life of transformers is determined by how seriously the coil insulating paper has been deteriorated, and furfural in the oil was found effective for the parameters. Particularly, application of the NN was revealed to be effective in estimating electric motor deterioration. A high-temperature sulfide corrosion rate estimating model was developed from the operation and measurement data of the facilities by applying the NN and TCBM. (NEDO)

  14. Achievement report for fiscal 2000 on development of technologies to reduce pollutants in oil refining; 2000 nendo sekiyu seisei osen busshitsu teigen nado gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development has been made on technologies to reduce sulfur content in light oil and on optimization of light oil quality. This paper summarizes the achievements in fiscal 2000. In the study of enhancing the desulfurization rate in gas oil deep hydrodesulfurization process, it was found that NiHY zeolite having Ni introduced by using the ion exchange method shows stable activity, whereas the target of sulfur content of 50 ppm or lower was achieved by adding the third constituent and by optimizing the impregnation solution to pH3. In the study of the Ni, Mo/alumina catalyst, the desulfurization activity was enhanced by optimization of carrier pore size to 120 to 140 angstroms and by addition of phosphorus and silica, having the target of sulfur content of 50 ppm or lower achieved. In the research of manufacturing low-sulfur light oil using heavy oil desulfurization and hydrocracking, optimization was performed on the catalyst used in the latter stage of heavy oil desulfurization, and evaluation was given on the performance in combination of commercially available hydrometallation catalyst/middle part HDS catalyst/bottom part HDS catalyst. As a result, achievement of the target of sulfur content in the desulfurized light oil of 300 ppm or lower was verified. Life evaluation test is in continuation on the heavy oil hydrocracking catalyst. (NEDO)

  15. Fiscal 1998 achievement report. Research and development of simplified dioxin analyzing technology, etc.; 1998 nendo dioxin kan'i bunseki gijutsu nado kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A simplified method is developed, which measures dioxins in flue gas without using GC/MS (gas chromatography/mass spectrometry) of the double focusing type. The sampling device is built of two collecting bottles, containing water and diethylene glycol, and uses no XAD-2 (cross-linked amberlight divinyl benzene) resin. Such a design does not need time consuming Soxlet extraction in the sampling process and shortens the processing time. An HPLC (high performance liquid chromatography) system replaces the convenient column chromatography system in the cleanup process, and this enables automation and rapid treatment. For the measurement of toxicity equivalent, GC/MS is used to separate and quantify 17 kinds of toxic isomers as in the conventional method. The GC/MS is of the quadruple focusing type, however, and this reduces the device cost at the initial stage and shortens the time for operators to acquire the skills of maintenance and operation. Though the quadruple focusing type is inferior to the double focusing type in sensitivity, the shortcoming is compensated for by massive specimen injection using a PTV (programmable temperature vaporizer). The result of a JIS (Japanese Industrial Standard) method and the result of this newly developed method are found to agree excellently with each other. This method is simple and efficient, suitable for use in the analysis of small incinerator flue gas. (NEDO)

  16. FY1998 research report on the R and D on recycling technology. Part 1; 1998 nendo recycle nado kankyo gijutsu kekyu kaihatsu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project aims to develop recycling technology for reduction of environmental burden caused by waste, and promotion of recycling of wastes. As for advanced recycling technology for PET bottles, the facility was improved for improvement of a facility operability and product quality. Study was made on the effect of a raw bale quality and recycled flake colors on a product quality, the forming test with PS or PET labels, and the concentration and effect of washing liquid circulated in flake washing process. As for recycling technology of hard-to-dispose waste plastics, facility improvement and demonstration test were made for continuous operation of dry-distillation/gasification of shredder dusts and separation of nonferrous metals and glass. Study was also made on pulverizing and recycling technologies of FRP bath tubs, and such pulverization costs were estimated. As for production technology of chemical feed and fuel from wastes, study was made on removal technology of non-flammable substances, development of alkaline additives, reacting condition, development of reactors, and use technology as chemical feed. (NEDO)

  17. Report on technological trend survey in fiscal 2000. Survey on bio-technology development strategy; 2000 nendo gijutsu doko nado chosa hokokusho. Bio technology gijutsu kaihatsu senryaku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Survey and research have been performed on bio-technologies as to their seeds of technological development projects to be worked on by the government from the viewpoint of industrial utilization technologies. In the survey on the trends of research and development and technological development on human-genomes, the survey has been done on the status of execution in the Millennium Genome Project, and how the works related to human-genomes are done at the bio-related government based research organizations and the private sector research organizations. Trends related to the human-genome research in overseas countries were also surveyed. With regard to the future prospect of research and development in the post genome age, discussions were given on the result of the questionnaire survey on opinion leaders in the industrial, governmental and academic areas. In discussing the viewpoint of the industrial utilization technologies related to human genomes, candidates assumed usable in the genome related application fields were discussed, and a basic framework of a technological map was prepared. Based on the results thereof, the technological development areas anticipated to be important in the future were extracted, and the technological development themes were discussed. (NEDO)

  18. Analysis and evaluation of data to accompany the development of geothermal water use power plant, etc. Analysis and evaluation of polymeric materials exposed to geothermal heat at depths; Nessui riyo hatsuden plant nado kaiahtsu ni tomonau data no kaiseki hyoka. Shinbu chinetsuyo kobunshi zairyo no kaiseki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kenmochi, K.; Takahashi, J.; Takayanagi, H.; Tsuda, H.; Nagai, H.; Takeuchi, K. [Agency of Industrial Science and Technology, Tokyo (Japan); Nagasawa, C. [Kumamoto Prefectural Industrial Technology Center, Kumamoto (Japan); Hamada, T. [Science University of Tokyo, Tokyo (Japan). Faculty of Industrial Science and Technology

    1998-11-20

    Remaining life assessment technologies for polymeric materials for geothermal power generation and methods for improving their heat resistance are reviewed, and concepts of scale-free technologies for FRP (fiber-reinforced plastic)-sandwiched pipelines for hot water transportation are described. Materials based on PTFE (polytetrafluoroethylene) and NBR (acrylonitrile-butadiene rubber) are chosen for use as DHM (down-hole motor) sealing material and for application to the stator. With PTFE as the matrix, four candidates are prepared, which are additive-free PTFE, and GF/PTFE, GF/CF/PTFE, CF/PTFE, each containing 20w% GF (glass fiber) and/or 20w% CF (carbon fiber). With NBR serving as the matrix, two candidates are prepared, which are NBR-A containing 20w% aramid fiber and NBR-W which is a vulcanized NBR-A. External force, heat, light, and mud are named as the degradation factors, and each factor and some combinations of external force, heat, and light are repeatedly imposed on the materials. During the effort to develop an apparatus for simulating geothermal circumstances in which the factors will affect the materials in complicated ways, a life assessment technique is developed for such polymeric materials. A technology is developed for providing polymeric rubber elastomer with a heat resistant feature. A study is made to replace transportation pipelines for injection wells with FRP sandwiched pipelines. (NEDO)

  19. Comparación de los efectos del D-004, imipramina y sertralina en el modelo de nado forzado en ratones

    Directory of Open Access Journals (Sweden)

    Daisy Carbajal Quintana

    2012-09-01

    Full Text Available Introducción: La finasterida, inhibidor de la 5 a-reductasa, se emplea en el tratamiento de la hiperplasia prostática benigna, y ocasiona entre sus efectos adversos un aumento de cuadros de depresión. El D-004 es un extracto lipídico extraído a partir del fruto de la palma real (Roystonea regia, inhibe la 5 a-reductasa y previene la hiperplasia prostática benigna, y muestra un efecto antidepresivo moderado en el ensayo de nado forzado y suspensión por la cola. Objetivo: comparar el efecto del D-004 con la imipramina y la sertralina sobre la duración de las conductas de inmovilidad, nado y escalado en el ensayo de nado forzado. Métodos: se distribuyeron los ratones en ocho grupos: control (vehículo, tres tratados con D-004 (100, 250 y 500 mg/kg, dos con sertralina y dos con imipramina (30 y 50 mg/kg respectivamente. Estos se colocaron en un cilindro de cristal que contenía agua a una altura de 6 cm y se cuantificaron las conductas. Resultados: la administración oral de D-004 (100, 250 y 500 mg/kg durante 14 días redujo significativamente el tiempo de inmovilidad con respecto al grupo control (17, 22 y 25 % y aumentó significativamente la conducta de nado en 1,58, 1,68 y 1,74 veces. Este efecto resulta moderado (25 % comparado con las reducciones alcanzadas por la sertralina y la imipramina (³ 60 %. Las dosis mayores (250 y 500 mg/kg ocasionaron incrementos de la conducta de escalado, 2,79 y 3,55 veces superiores a la del grupo control, lo que mostró semejanza con la imipramina, aunque con una menor eficacia. Conclusiones: el D-004 ejerce un moderado efecto antidepresivo, lo que pudiera contribuir al manejo de los pacientes con hiperplasia prostática benigna en los cuales se informa coincidencia de cuadros depresivos.

  20. FY 1999 report on the development of technology to recycle architectural waste materials, glass, etc. Development of technology to recycle architectural waste materials; 1999 nendo kenchiku haizai glass nado recycle gijutsu kaihatsu seika hokokusho. Kenchiku haizai recycle gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    Waste wood materials in the materials discharged from architectural disassembly were regarded as a potential wood resource, and the R and D of the technology to recycle these were conducted. Studies were made on the technology to finely grind waste wood materials, technology to compress/form waste wood materials and ground wood powder, verification of strength characteristics/dimension stability of the formed wood materials, etc. As to the wood materials which were badly degraded under ultra violet rays, they were coloring-processed by the steam treatment, and a possibility of coating substitution was confirmed. In relation to the technology to produce compressed wood materials, the optimization of heat treatment conditions was experimentally conducted. About the technology to give dimensional stability, dimensional stability was improved as a result of the improvement of chemicals feeding and the development of chemically processed drugs. In the development of light formed products, the board was successfully formed which is light in weight using lignocelluloses/inorganic hydrates and has the bending strength higher than that of the plaster board. In the development of interior materials, the technology was developed in which ground wood powder and thermo-plastic resin are mixed for die molding, and the OA floor using this was commercialized. (NEDO)

  1. FY 1999 report on the results of the R and D on high performance industrial furnace, etc.; 1999 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In the development of high performance industrial furnace, initial targets were achieved such as energy saving of 30%, downsizing of 20%, and a remarkable NOx reduction. To verify the achievement, the test field project is being worked on by NEDO. In FY 1998, 23 heating furnaces, 29 heat treat furnaces and 6 melting furnaces were under the project at energy saving effect of 52,000 kl converted to crude oil. In FY 1999, 18 heating furnaces, 26 heat treat furnaces and 7 melting furnaces are now under the project at energy saving effect of 57,000 kl. The project was awarded 'The 9th Nikkei Global Environmental Technology Prize.' The themes for the R and D are as follows: high efficiency exhaust heat utilization system, self-completion type high temperature/high radiation heating technology, technology to make heat transfer in steel heating suitable under non-stationary state, high efficiency heat transfer technology, technology to optimize the shape of heating furnace, high performance atmosphere heat treat furnace, high efficiency heat transfer technology by high temperature jet flame heating, technology of high efficiency aluminum melting furnace, technology to improve soaking degree in steel heating, high performance tubular heating furnace in oil refining, optimum combustion control technology of regenerative burner furnace, and laser measuring method inside industrial furnace. (NEDO)

  2. Fiscal 1996 verification survey of geothermal exploration technology. Development of the fracture type reservoir exploration method (development of the elastic wave use exploration method); 1996 nendo chinetsu tansa gijutsu nado kensho chosa. Danretsugata choryuso tansaho kaihatsu (danseiha riyo tansaho kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of exploring accurately fracture groups greatly restricting the fluid flow of geothermal reservoirs, technical development was made for applying the elastic wave exploration technology such as the high precision reflection method, VSP, elastic wave tomography to the geothermal exploration. The Okiri area, Kagoshima prefecture was selected as a demonstrative field of a typical type where the steep and predominant fracture rules the geothermal reservoir, and experiments were conducted using the high precision reflection method and VSP. Fracture models were made, and the analysis results were studied by a survey using the array CSMT/MT method and by a comparison with existing data. Reformation of the underground receiving system used for VSP and elastic tomography is made for improvement of its viability, and was applied to the VSP experiment. The treatment/analysis system of the core analyzer was improved, and cores of the demonstrative field were analyzed/measured. Further, the exploration results, core analysis results and existing data were synthetically analyzed, and fracture models of the demonstrative field were constructed. Also, effectiveness and viability of the elastic wave use exploration method were studied. 90 refs., 418 figs., 24 tabs.

  3. Research and development of utilization technology of solar thermal energy system for industrial and other use. International joint technology development for solar energy utilization systems; Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for international joint technology development for solar energy utilization systems. The joint study with an Indonesian research institute takes a model of lumber drying plant for the design and feasibility study. All the parts it needs are technically available in Indonesia, except carbon fiber sheets and electronic devices for controlling purposes. The drying cost is higher than that of a plant which procures charge-free wood fuel, but lower than that of a plant which procures fuel at 30$/t. A cacao drying plant model is also studied. The feasibility study shows that the initial investment for the blowing-up model is much higher by 60% to 100% than that for the conventional plant. Its fuel cost is lower by 11% than that of residual oil but 27% higher than that of wood. 4 figs.

  4. Fiscal 2000 achievement report. Development of technologies for waste treatment and recycling (Development of technologies for appropriate treatment of air bags); 2000 nendo haikibutsu recycle kanren gijutsu kaihatsu seika hokokusho. Air bag tekisei shori gijutsu no kaihatsu nado

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A centralized treatment process respecting environmental protection and safety for unused air bags aboard disused automobiles is developed. In concrete terms, a heating facility owned by Daicel Chemical Industries, Ltd., is used, which includes an apparatus for examining exhaust gas dioxins and an exhaust gas treatment apparatus and, with this facility, studies are made for appropriately treating waste gas and waste water to be generated when air bag modules undergo centralized heating. Endeavors in fiscal 2000 center about (1) the development of waste gas treatment technologies, (2) development of waste water treatment technologies, (3) chemical analysis of waste water sludge, dusts and air bag residues, and (4) the study of appropriate treatment of non-azide air bag modules. As to the development of exhaust gas treatment technology, it was proved that the exhaust gas treatment system consisting of secondary incineration furnace, exhaust gas cooling tower and bag filter worked effectively. (NEDO)

  5. Fiscal 1998 research report on development of the advanced industrial furnace (R and D on the advanced industrial furnace). Volume 3; 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes the research results of the chapter 4 and 5 (experimental database) from the research report on development of the advanced industrial furnace. The chapter 4 summarizes functions of the temperature performance evaluation simulator of the advanced continuous heating furnace for the database system, and various research results obtained by the simulator. This chapter also summarizes the research result on the applicability of high-temperature air combustion to other industries, the patent research result on heat storage combustion technology, the basic technology research result, and the reaction analysis result by FLUENT. The chapter 5 summarizes the combustion experiment data collection by developing self-completion high-temperature high-radiation heating technology. As for R and D on technology optimizing the profile of heating furnaces, the following data are summarized: measurement data of heat transfer in furnaces and heat flux data at right overhead furnace temperature under cold air and preheated air combustion in conventional furnaces, and heat storage combustion. (NEDO)

  6. FY1999 technological development of wind power generation systems for islands. Development of wind power generation systems in islands; 1999 nendo ritoyo furyoku hatsuden system nado gijutsu kaihatsu. Rito ni okeru furyoku hatsuden system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective of developing wind power generation systems that suit small to medium size islands in Japan, conceptual design was made on a 100-kW class wind mill to satisfy such requirements as no need of large heavy machines, and gust resisting performance. Investigations were performed on sites suitable for demonstration tests thereof. This paper reports the achievements in fiscal 1999. In investigating the site location feasibilities, which took small to medium size islands in Okinawa Prefecture as the discussion objects, environmental investigation, wind condition forecast and investigation, and system linkage investigation were carried out, whereas one point each in three islands were extracted as the promising sites. The system discussion and design called for wind velocity resistance of 80 m/s, system linkage percentage of 40% at maximum, power generation cost of 20 yen per kWh, design life of 20 years, constructability of requiring no large heavy machines, and operation mode of diesel hybrid use. Along with these specifications, conceptual design was performed on the system constituting elements, such as wind mill blades, generators, electric power control devices, and towers. In the blade aerodynamic test, wind tunnel tests were executed by using three types of blade wings. Sample blades were fabricated for the preparation of blade material tests. (NEDO)

  7. Surveys for promoting development of overseas coals in fiscal 1999. Surveys on international coal situation; 1999 nendo kaigaitan kaihatsu kodoka nado chosa (kaigaitan kaihatsu sokushin chosa). Kokusai sekitan jijo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Detailed surveys were performed on Britain, Germany and Spain being the major coal producing countries in Europe with regard to a general view on the status of energy demand and supply, the status of demand and supply of coal, business institutions, and related policies in each country. The status of demand and supply of coal, and related policies in the three countries may be summarized as follows: In Britain, the ratio of coal accounted for in the primary energy supply is 18.0% in 1998, and the coal production amounted to 35.5 mill.TCE/year; closure of underground mining coal mines is discussed recently; the congress is deliberating re-introduction of the subsidy system which had been once discontinued; in Germany, the ratio of coals accounted for in the primary energy supply in 1997 was 14% in bituminous coal and 11% in brown coal; the quantities of production of bituminous coal and brown coal in 1998 were 41.8 and 50.6 mill.TCE/year, respectively; the number of mines has decreased because of the unification; the subsidy policy is in continuation; in Spain, the ratio of coal accounted for in the primary energy supply was 13.5% in 1997 and the quantity of coal production in 1998 was 12.5 mill.TCE/year; unification of coal operators has not been advanced as far as in Germany; and the subsidy is provided as in Germany. (NEDO)

  8. Report on research results of the development of high efficient boilers in fiscal 1996. Research development of high efficient industrial furnaces, etc; Koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Out of the developments of high efficient boilers which have been continued since fiscal 1993, the paper reported the result of the development conducted in fiscal 1996. The oxygen combustion (the oxygen enrichment combustion including 100% oxygen combustion) decreases the amount of flue gas and reduces heat loss of the flue gas, and is also effective as NOx reduction measures. The experiment was conducted using testing furnace. The boiler efficiency rapidly increased with the increasing concentration of oxygen enrichment. In the pure oxygen combustion, the overall boiler efficiency of a 106% level (low heating value standard) is expected. Since the boiler wet flue gas is decreased, the NOx emission is reduced. The boiler can raise the combustion temperature with no fear of NOx and can be reduced in size. CO2 decreases in proportion to the energy saving effect. The development of a condensation flue gas heat exchanger is aimed at recovering heat down to the low temperature. Prediction of heat transfer in the steam condensation region becomes possible, and the size reduction can be expected. Dew point corrosion resistant materials were also selected. As to the high speed combustion control, a simple type using micro-processor was developed. Obtained were high speed, compactness, electric power saving, and high controllability. 14 refs., 306 figs., 88 tabs.

  9. Verification survey of geothermal exploration technology, etc. Report on the result of the developmental research on the development of the fracture type reservoir exploration method; Chinetsu tansa gijutsu nado kensho chosa. Danretsugata choryuso tansaho kaihatsu kenkyu kaihatsu seika sokatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of grasping fracture groups forming geothermal reservoirs with accuracy, the development of the fracture type reservoir exploration method has advanced the technical development of exploration methods of seismic wave use, electromagnetic induction use, and micro-earthquake use. This paper summarized main results of the development and problems to be solved in the future. In the development of the seismic wave use exploration method, the high accuracy reflection method using seismic wave, VSP and seismic tomography were adopted to the geothermal field, and technology effective for the exploration of fracture type reservoirs was developed. In the development of the electromagnetic induction use exploration method, the array CSMT method which can measure multiple stations along the traverse line at the same time was developed with the aim of grasping effectively and accurately fracture groups forming geothermal reservoirs as changes of resistivity in the shallow-deep underground. In the fracture group forming geothermal reservoirs, micro-earthquakes are generated by movement of thermal water and pressure variations. In the development of the micro-earthquake use exploration method, developed was the micro-earthquake data processing and analysis system (MEPAS). 179 refs., 117 figs., 28 tabs.

  10. FY 1999 achievement report on the development of high performance boilers. R and D on high performance industrial furnaces, etc.; 1999 nendo koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project started in FY 1993 to survey the actual state of industrial use boilers. Based on the results of the survey, in fiscal 1995, 1996 and 1997, no improvement of the present technology which has limits, but the development was made of the oxygen combustion and element technology which are factors for heightening boiler performance with a new idea first in the world. In fiscal 1998, a target for the overall thermal efficiency of 105% was settled by testing a pilot plant where the element technology was integrated into the small once-through boiler, flue/smoke tube boiler, water tube boiler, etc. In fiscal 1999, the target of the overall thermal efficiency of boiler was reached by a pilot plant test to clarify combustion characteristics, heat transfer characteristics, environmental characteristics, etc. Further, effects of energy saving were increased by the adoption method of oxygen supply equipment. Concretely, an overall boiler efficiency of 105.73% exceeding the targeted value of 105% was achieved at a pilot plant of actual scale, by concentrating the results of each of the element technologies such as 'oxygen combustion,' 'condensation type flue gas heat exchanger,' 'high performance combustion control device,' and 'rapid rotating auxiliary machine.' (NEDO)

  11. FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on technology development of utilization of biological resources such as bioconsortia (development of analytical techniques of bioconsortia); 1997 nendo sangyo gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Bioconsortia are microbial composites composing of more than two kinds of microorganisms with special functions. To utilize their advanced functions, some techniques have been developed for analyzing their functions and interactions, and for identification, separation and incubation of the constituent microbial groups. In FY 1997, an investigation was made on technology trends, domestic researchers, and research topics related to bioconsortia. To manage and promote the progress of research at the National Institute of Bioscience and Human-Technology where the centralized management of this project is conducted, meetings are held once a month to examine the progress at the institute, in which reports are made and discussions are held on how each research item is progressing. In addition, meetings of the committee to promote research are held every other month to consider and examine measures required for promoting the research. Re-entrustment of research has been made on two subjects, i.e., `Studies on biological significance of symbiotic microorganisms` by Prof. Ishikawa of the University of Tokyo, and `Study on the relationship between the biosynthesis of useful terpenic materials of plant origin and the differentiation of plant tissues, and their effective production by plant cell cultures` by Prof. Inoue of Gifu Pharmaceutical University. 27 refs., 13 figs., 1 tab.

  12. Antidepressant behavioral effects of duloxetine and fluoxetine in the rat forced swimming test Efeitos antidepressivos da duloxetina e da fluoxetina no teste do nado forçado em ratos

    Directory of Open Access Journals (Sweden)

    Leandro Ciulla

    2007-10-01

    Full Text Available PURPOSE: To compare the effects of the antidepressant drugs duloxetine and fluoxetine on depressive behaviors in rodents. METHODS: Eighteen male Wistar rats were given systemic injections of duloxetine, fluoxetine, or saline prior to a Forced Swimming Test (FST. Immobility and number of stops were measured. RESULTS: Rats given injections of fluoxetine displayed significantly less immobility (p = 0.02 and fewer stops than the control group (p = 0.003. Duloxetine significanlty reduced the number of stops (p = 0.003, but did not effect immobility (p = 0.48. CONCLUSION: Duloxetine and fluoxetine reduced depressive behaviors in the Forced FST. However, our findings suggest that fluoxetine is more effective than duloxetine.OBJETIVO: Comparar o efeito antidepressivo da droga cloridrato de duloxetina com a fluoxetina. MÉTODOS: O teste do nado forçado, teste comportamental que avalia a atividade antidepressiva em ratos, foi utilizado em 18 ratos Wistar, machos adultos, divididos em três grupos iguais: duloxetina, fluoxetina e controle. RESULTADOS: Os dados do teste do nado forçado foram analisados pelo teste One-way ANOVA, Mann Whitney e Kruskall-Wallis.Houve diferença significativa (p = 0,003 entre o número de paradas dos grupos duloxetina e fluoxetina e o grupo controle. CONCLUSÃO: A duloxetina e a fluoxetina tiveram frequência de paradas similares. A fluoxetina mostrou ser mais efetiva que a duloxetina no teste do nado forçado em ratos.

  13. Transtorno do comportamento alimentar em atletas de elite de nado sincronizado Eating disorders in elite synchronized swimmers

    Directory of Open Access Journals (Sweden)

    Talita Adão Perini

    2009-02-01

    Full Text Available OBJETIVOS: O objetivo do presente estudo foi identificar a presença de transtorno do comportamento alimentar (TCA ou síndromes precursoras e o grau de distorção da imagem corporal em atletas de elite de nado sincronizado. Essa modalidade é considerada de risco para desenvolvimento de TCA por valorizar, além de outros aspectos, a leveza e beleza de movimentos que, de certa forma, estão associados a baixa massa corporal. MÉTODOS: Foram avaliadas 27 atletas de nado sincronizado, sendo 19 da categoria juniores (15,6 ± 0,8 anos e oito da categoria de seniores (19,0 ± 1,3 anos que compunham a seleção brasileira na época do estudo (2000. Um grupo de 32 adolescentes não-atletas (15,0 ± 1,6 anos foi usado para comparação com as atletas. Os procedimentos metodológicos adotados foram: aplicação de três instrumentos de auto-relato, validados. 1 EAT-26 - presença de comportamentos alimentares inadequados; 2 BITE - presença de atitudes sugestivas de bulimia nervosa; e 3 BSQ - insatisfação da auto-imagem corporal. RESULTADOS: Embora tanto o grupo de atletas, quanto o de não-atletas tenham apresentado parâmetros antropométricos compatíveis com padrões saudáveis para a idade e sexo, os resultados evidenciam a presença de insatisfação com a auto-imagem corporal e a adoção de práticas patológicas de controle da massa corporal, sobretudo entre atletas da categoria juniores e entre as adolescentes não-atletas. CONCLUSÕES: Os resultados encontrados no presente estudo retratam uma tendência mundial de preocupação com a aparência entre adolescentes capaz de levá-las à adoção de condutas não-saudáveis.OBJECTIVES: The aim of the present study was to identify the Eating Behavior Disorder (EBD or precursory syndromes and the level of distortion of the body image of elite synchronized swimming athletes. This sport modality is considered of risk for development of eating disorders for valuing, among other aspects, the

  14. Efeito do treino com elástico cirúrgico na melhora do desempenho de jovens nadadores na distância de 50 metros na técnica de crol : efeito da utilização de tarefas de treino de velocidade de nado resistido com elástico cirúrgico na melhora do resultado obtido num teste de 50 metros de crol em jovens nadadores

    OpenAIRE

    Rezende, Mônica dos Anjos Costa de

    2010-01-01

    Dissertação de mestrado em Biocinética, apresentada à Faculdade de Ciências do Desporto e Educação Física da Universidade de Coimbra Este estudo consiste na avaliação do efeito de treino com nado resistido, através do uso de um elástico cirúrgico (série 3x4x20” três vezes por semana), durante um período de cinco semanas sobre a força propulsiva e a velocidade de nado numa prova de 50 metros nado de crol. A amostra constou de 22 jovens atletas de dois países, 10 (5 masculino, 16,0 anos ±0,3...

  15. Advanced research and development of gas hydrate resources. R and D of exploration and others - R and D of excavation technologies and others - surveys/researches on methods of evaluating environmental effects - surveys/researches on application systems; Gas hydrate shigenka gijutsu sendo kenkyu kaihatsu. Tansa nado ni kansuru kenkyu kaihatsu / kussaku gijutsu nado ni kansuru kenkyu kaihatsu / kankyo eikyo hyokaho no chosa kenkyu / riyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Gas hydrate is a clathrate compound in a gaseous molecule as the host, stable under relatively mild environments. It is deposited in the 600m or deeper sea bottoms to form the gas hydrate deposit and massively occurring in the sea areas around Japan. This deposit has been studied viewed from natural gas resources, causes for natural hazards and contribution to the global warming. This project excavates a well in the deposit, to study possibilities of the technologies for decomposing, fluidizing and lifting the hydrate as the gas source, and for establishing the natural gas transporting/mooring systems in which its characteristics are utilized. The R and D activities are directed to the 4 areas, (1) development of the exploration technologies to determine the deposit sea area, quantity and conditions, (2) development of the stable well-excavation technologies, (3) studies on the effects of gas production on the environments, and development of the system for predicting the effects, (4) and studies on the application systems. The item (3) finds out the transportation/storage system possibly more economical than the current freezing/liquefaction technologies. The item (3) has the development themes of evaluating the geohazards caused by excavation and gas production, and their effects on the ecological systems. (NEDO)

  16. Report on the achievements in fiscal 1999. Technology to use gas hydrate as a resource (Research and development for exploration, research and development on drilling technologies, investigative research on an environment influence evaluation method, and investigative research on a utilization system); 1999 nendo gas hydrate shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansa nado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The contents of the research and development performed in the current fiscal year are as follows: (1) research and development for exploration, (2) research and development on drilling technologies, (3) investigative research on an environment influence evaluation method, and (4) investigative research on a utilization system. In Item (1), element analysis data are used to study a method to estimate production environment of hydrate ore beds by using an inorganic ion analyzer and a trace amount element analyzer, the crust thermal flow measuring method is used to discuss a method to analyze the hydrate stability zones together with the data of sea area exploration records, and conceptual design is made on a resource potential evaluation system. In Item (2), experiments and analytical discussions are performed on decomposition control of the gas hydrate solid-liquid interface according to such conditions for the drilling fluid as temperatures and flow rates. Elucidation is given on the initial process of bubble generation for behavior of decomposed gas bubbles. Observation and elucidation are made on two-phase flow behavior of non-Newtonian fluid. In Item (3), conceptual design is carried out on a system to detect elements of shape change in each bed due to fluid movement in a gas hydrate bed and an upper bed. In Item (4), discussions are given on the optimizing conditions for generation and dissociation of gas hydrates. Investigation is made also on a possibility of the transportation and storage system. (NEDO)

  17. Efeito do destreinamento sobre variáveis cinemáticas relacionadas ao desempenho do nado crawl com diferentes estratégias de respiração

    OpenAIRE

    Pereira, Bernardo Maia Farage

    2012-01-01

    Sabe-se que o destreinamento acarreta em perda das adaptações do sistema cardiorrespiratório e neuromuscular adquiridas com o treinamento físico, inclusive na natação. Apesar de diversos estudos terem investigado o efeito do destreinamento do ponto de vista fisiológico, ainda não foi encontrado na literatura estudos que tenham investigado o efeito do destreinamento em variáveis cinemáticas durante o nado. Sabendo disso esse trabalho foi desenvolvido com objetivo de verificar se há efeito do d...

  18. Surface swimming behavior of the curculionid Ochetina uniformis Pascoe (Erirhininae, Stenopelmini and Ludovix fasciatus (Gyllenhal (Curculioninae, Erodiscini Comportamento de nado superficial exibido pelos Curculionidae Ochetina uniformis Pascoe (Erirhininae, Stenopelmini e Ludovix fasciatus (Gyllenhal (Curculioninae, Erodiscini

    Directory of Open Access Journals (Sweden)

    Wesley Oliveira de Sousa

    2007-03-01

    Full Text Available The swimming behavior exhibited by specimens of L. fasciatus and O. uniformis was analyzed frame-by-frame with video observation recorded with a digital camera, attached to a stereomicroscope. Adults of O. uniformis, an aquatic insect, swim with all three pairs of legs. During the process of swimming the majority of the abdomen and rostrum remain submerged, part of the fore and hind tibiae remain above the surface, while the mid tibiae remain submerged. The mesothoracic legs, during the power-stroke stage, provide the greatest thrust while the metathoracic legs provide the least forward propulsion. The prothoracic legs, extended forward, help to direct the swimming. The semi-aquatic specie L. fasciatus shows the same swimming style as O. uniformis, that is, with movement of all the three pairs of legs; the mesothoracic legs are responsible for the main propulsion. The insect body remains on the water surface during the process of swimming, while the legs remain submerged. Both species complete a swimming cycle in 0.33 and 0.32 seconds, respectively, with an average speed of 1.38 cm/s and a maximum and minimum swimming duration time of 11.15 and 5.05 minutes, respectively, for L. fasciatus. The swimming behavior exhibited by O. uniformis and L. fasciatus corresponds to the style known as a breast strokelike maneuver. This is the first record of this kind of swimming for both species here observed and increases to seven the number of genera of Curculionidae exhibiting this behavior.O comportamento de nado exibido por indivíduos de L. fasciatus e O. uniformis foi analisado quadro a quadro através de imagens obtidas com o auxílio de uma câmera fotográfica digital com opção de vídeo, acoplada a um estereomicroscópio. Foi demonstrado que O. uniformis, espécie aquática, nada com o auxílio dos três pares de pernas. Durante este processo a maior parte do abdome e rostro localizam-se abaixo da superfície da água, parte das t

  19. Fiscal 1997 report on the results of the New Sunshine Project subsidiary operation. Development of a geothermal water use power plant, etc. / technical development of the hot dry rock power generation system (development of electric technology); 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (koon gantai hatsuden system no gijutsu kaihatsu (yoso gijutsu no kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of using hot dry rock energy to power generation, the R and D was continued of element technology of the hot dry rock power generation. In fiscal 1997, the construction of ground facilities, etc. for long-term circulation experiment was proceeded with to make data analysis for study of the experimental results. As for preparation for the long-term circulation experiment, design/fabrication/construction of experimental facilities were commenced, and review/fabrication of the monitoring system were conducted to strengthen the monitoring network of microearthquakes. In relation to the analytical research, using models connecting reservoirs and wells, relationships were studied among the distance between injection well and production well, production flow rate, and long-term thermal extraction characteristics of reservoirs. Further, to study structures of shallow/deep reservoirs at the Hijiori hot dry rock experimental field, re-determined were mechanism solutions of AE in deep hydraulic fracturing experiments, three well circulation tests, and preliminary circulation tests, and at the same time stress fields were studied. Fracture models were made and the simulation program was revised. 18 refs., 82 figs.

  20. Development of hot water utilizing power plants in fiscal 1999. Development of binary cycle power plant (Development of system to detect well bottom information when geothermal hot water is excavated); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Binary cycle hatsuden plant no kaihatsu (chinetsusei kussakuji kotei joho kenchi system no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Developmental research has been performed on the MWD system to identify on the real time basis the information about well bottom when geothermal hot water is excavated (azimuth, inclination, pressure and temperature). This paper summarizes the achievements in fiscal 1999. In the developmental research on the detection device, attempts were made in improving the zonde, and enhancing its heat resisting performance. In addition, data were acquired on electronics parts as a result of the heat resistance identifying test. For the on-the-ground devices, improvement was made to add the experiment analyzing program with a program to remove the downhole motor pressure noise. The pressure noise during excavation in the actual wells was collected. In the analyzing system, use of PC, improvement, and operation check were performed on the well trace projecting and indicating system. Operation of the well trace estimating system was checked by using the actual data in order to prepare the operation manual. With regard to the well evaluation supporting system, improvement, operation check and that by using the actual data were executed on the PC version temperature analyzing system. Performance of the zonde was verified by the actual geothermal well test. (NEDO)

  1. Research and development of utilization technology of solar thermal system for industrial and other use. Development of system of advanced heat process type (chemical refrigeration and cold storage system using solar heat); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Advanced heat process gata system no kaihatsu (taiyonetsu reito reizo no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for chemical refrigeration and cold storage system using solar heat. The study on refrigeration materials are aimed at development of new hydrogen-occluding alloys which show good hydrogenation equilibrium characteristics and reactivity at temperature required for stand-alone refrigeration systems aided by solar heat, and still new hydrogen-occluding alloys operable at refrigeration temperature for lower-temperature systems. For the refrigeration materials capable of producing low-temperature heat of -10{degree}C at a regeneration temperature of 140{degree}C produced by solar heat, a La-Ni-Mn-Al alloy is selected for high-temperature use and a La-Y-Ni-Mn alloy for low-temperature use. The study on technology for refrigeration modules develops high-efficiency heat exchangers for refrigeration and regeneration, compatible with the hydrogen-occluding alloys. It also develops air-and water-cooling techniques for hydrogen-occluding alloys, where air is used as the heat source. The test apparatus is designed, installed and operated, to attain a low temperature of -10{degree}C or lower with a heat source of 140{degree}C and air heat source of 28{degree}C. 7 figs.

  2. Development of hot water utilizing power plant in fiscal 1998. Development of a binary cycle power generation plant (development of a 10-MW class plant); 1998 nendo nessui riyo hatsuden plant nado kaihatsu. Binary cycle hatsuden plant no kaihatsu (10MW kyu plant no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper summarizes the achievements in fiscal 1998 on developing a 10-MW geothermal power plant in the Hohi-Sugawara area being a representative area of middle-to-high temperature hot water resources. In designing the plant, domestic and overseas surveys were carried out on media suitable for binary cycle power plants, thermal cycle characteristics, construction cost, environmental effects, safety, operation, maintenance and control. Latest technologies were also surveyed and analyzed. The plant construction performed development construction around the testing devices, new construction of a plant control room building, constructions for installing electrical machines including the hot water system testing devices, river water intake facility construction, and cooling water intake facility installing construction. The environmental effect investigation included investigations on rain falls, river flow rates, hot springs, spring water, monitoring during the construction, and the state of transplantation of precious plants, and observation on groundwater variation. In verifying the geothermal water pumping system, factory tests were carried out on DHP3 demonstration machine which couples the pump section of a down-hole pump with the motor section, whose performance and functions were verified. (NEDO)

  3. Achievement report in fiscal 2000 on technical development to recycle waste building materials and glasses. Development of waste building material recycling technology (Research and development of wooden board manufacturing technology using demolished building lumbers); 2000 nendo kenchiku glass nado recycle gijutsu kaihatsu seika hokokusho. Kenhciku haizai recycle gijutsu kaihatsu (kenchiku kaitai mokuzai wo mochiita mokushitsu board seizo gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development has been made on a wooden board manufacturing technology re-utilizing demolished building lumbers and waste plastics with an intention of saving resources and reducing wastes. This paper summarizes the achievements in fiscal 2000. In developing the technology to re-use demolished building lumbers, a method for removing metals attached to demolished building lumbers was established by using a magnetic separator and a metal detector, with which it was verified that iron can be removed nearly 100%. With regard to waste plastics, simultaneous use of specific gravity separation utilizing centrifugal force and electrostatic separation provided a prospect that metals and plastics of high melting points can be removed from mixed resins in waste household electric appliances, and that polypropylene (PP), polystyrene (PS), and ABS can be classified at high accuracy. In manufacturing waste wood and waste plastic boards, pilot plants were built to use the 'melt spray method', 'melt blow method', and 'laminating method' as the means to spray molten resin onto wood raw materials, wherein trials were performed on mixing molten resins with wood flakes, and on board forming. (NEDO)

  4. Fiscal 1997 development of the geothermal water use power plant, etc. Development of the binary cycle power plant (10MW class plant); 1997 nendo nessui riyo hatsuden plant nado kaihatsu. Binary cycle hatsuden plant no kaihatsu (10MW kyu plant no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A R and D was conducted with the aim of using medium-/high-temperature hot water type geothermal resources. In fiscal 1997, fabrication of geothermal water system testing equipment and geothermal water production/reduction piping installation work were conducted, and an environmental effect survey and ground water variation observation were carried out. Moreover, pumps to pump up geothermal water were fabricated. In the fabrication of a pump for No. 3 demonstration plant, the following improvements were made. Concerning the inlet undersea bearing, the shapes related to it were so reformed that external water feeding in the initial run can be done. Relating to the protection of the thrust bearing half load side friction face, a spring was added to the face so that it was structured to give preload. As a method to install a casing covering board, adopted was a band installation method which is easy in handling. The number of instrumentation cables was reduced. As to cables for downhole pumps, studied were methods of connection, etc. of connection portions of the motor connector and instrumentation cable. Moreover, purifying/regeneration facilities of the downhole pump bearing oil were fabricated and tested. 85 figs., 57 tabs.

  5. Report on results concerning development of supermetal technology (FY1999-2000). Development of evaluation technology for formability of super metal (development of evaluation technology for formability of recrystallized microstructured plate); Super metal no gijutsu kaihatsu seika hokokusho (1999 - 2000 nendo). Super metal no seikeisei hyoka gijutsu nado no kaihatsu (bisai saikesshotsububan no seikeisei hyoka gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In connection with the innovative manufacturing of large base materials having a mesoscopic grain structure by means of technologies for high deformation accumulation control, recovery/recrystallization control, etc., research was conducted on evaluation technology for various characteristics such as formability, with fiscal 2000 results compiled. For the purpose of evaluating average grain size from an optical microscopic photograph of structures, it was judged reasonable to determine the average cut piece length. A device introduced to this development project was a horizontal goniometer capable of ODF (crystallite orientation distribution function)/pole figure measurement, qualitative analysis, and residual stress measurement. With warm rolling performed by controlling both material temperature of 7475 based alloys and roll temperature, thermally stable micro sub-grain structures were obtained. As a result of ODF analysis of this warm-rolled material, it was found that a {beta} orientation group existed very sharply in the area from the sheet surface to the center planar part of the thickness. The grain refinement of 5083 based alloys using a warm rolling method was also successful, with its ODF analysis revealing that the accumulation of the {beta} orientation group was very high as in the 7475 based warm-rolled materials. (NEDO)

  6. Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the technology to fix and effectively use carbon dioxide using bacteria and microalgae (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku (saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of contributing to the solution to the global environmental problem, a technology is developed in which by searching for/breeding/developing bacteria, etc. which conduct photosynthesis highly effectively, CO2 is fixed and recycled. The fiscal 1996 R and D is outlined as the utilization of bacteria, microalgae, etc. Obtained were microalgae exceeding the conventional strains in CO2 fixation ability, and bacteria/microalgae excellent in production of polysaccharides, hydrocarbon, lipid, biological active substances, etc. The fundamental study was continued of CO2 integrated enzyme function/reaction system as molecular biological breeding. In the cell fusion, a set-up of conditions for green algae was started. For the confirmation of performance of high dense/quantity culture technology using solar light, further improvement of performance and systematization, 200L scale testing equipment was manufactured. It is a collective reactor and enabled study of ventilation/agitation and control of light strength. A reactor analysis model was constructed. Also including the conversion into useful substances, energy/material balance was systematically studied. Collection of technical literature and information exchanges were made in Japan and overseas. 276 refs., 475 figs., 156 tabs.

  7. Fiscal 2000 report on financially supported geological structure survey overseas. Basic survey for coal resource exploitation (Research on underground probing technology); 2000 nendo kaigai chishitsu kozo chosahi nado hojokin (sekitan shigen kaihatsu kiso chosa) konai tansa gijutsu chosa hokokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the work of searching for coal beds, comparison is made between the geological structure of the object area, which is predicted, before actual investigation, by a close scrutiny of the result of oceanic pilot boring conducted in the past, result of geophysical exploration, and the geological features of galleries already in presence in the vicinity, and the result obtained from galleries drilled actually for the investigation. The investigation was conducted at the Ikeshima coal mine, Nagasaki Prefecture. In this fiscal year, 5 investigation galleries were drilled, totalling 1640m in length, and, in the mine, geological surveys, survey and measurement, coal quality evaluation, water emergence investigation, boring for coal, etc., were carried out. Comparison was made, and, though in the 2nd Minami No. 06 air duct there was no important difference detected between the prediction and the actual result, some faults were found to exist which had not been predicted by seismic exploration on the ocean. In the 2nd Minami No. 5 air duct, the actual geology was not different from the predicted geology, this endorsing the usefulness of boring for coal. In the 2nd Minami No. 01 gallery, direction and inclination were not greatly different from what had been predicted, but some faults which had not been predicted were discovered. These faults had escaped the scrutiny of neighboring coal beds and pilot boring. (NEDO)

  8. Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Feasibility study project on liquid fuel conversion); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Ekitai nenryo tenkan kanosei chosa nado jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This article comprises Part 1 on 'surveys of gas fields fit for a new methanol manufacturing process' and Part 2 'reports on overseas surveys of gas fields fit for a new methanol manufacturing process.' In Part 1, surveys are conducted on the existence, exploitation, and the actual utilization of natural gas resources, and on the status of natural gas industry related infrastructures in the Middle East. Proved natural gas reserves in Iran were 742tcf (trillion cubic feet) as of 1996-end, which was the largest in the world next to Russia. As for Kuwaiti natural gas resources, they all accompany oil production, with the proved reserves marking 52.4tcf as of 1996-end or the smallest in the Middle East. In Egypt, there were proved reserves of 20.4tcf as of 1996-end, and further existence of 30-40tcf is predicted. Proved reserves in Yemen are approximately 15tcf. Proved reserves in Oman were 30tcf as of 1996-end. It is expected that there will be a 1.4% increase in the demand for methanol for automobiles. The annual demand for methanol for power generation is 720,000 tons. In Part 2, on-site surveys of infrastructures and the like indispensable for methanol plant installation are reported. (NEDO)

  9. Fiscal 1999 report on results. Development item, 'development of evaluation technique for biocompatibility and the like of porous materials'; 1999 nendo takozairyo no seitai tekigosei nado hyoka gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of establishing fundamental technologies for ceramic porous materials that are excellent for artificial bone for a living body, evaluation technologies were developed for mechanical properties and biocompatibility, with fiscal 1999 results compiled. Performed for the examination of the mechanical properties were flexural test, compression test, tensile test, shearing test, torsion test, fatigue test, etc., with an evaluation testing method studied assuming that ceramic porous materials were applicable to implanting members. In the evaluation of biocompatibility, five kinds of osteoblast-like cell lines were cultured on a plastic disk and a dense hydroxyapatite disk, with adhesion and proliferation of the cells compared. Since these osteoblast-like cell lines adhere and proliferate on the surface and in the pore of hydroxyapatite, evaluation of the biocompatibility such as cell affinity was found possible with this in vitro method. With the view of obtaining principles for designing new bioactive ceramics, a method was developed for evaluating apatite-forming abilities of metal oxide gels having different compositions and structures in simulated body fluid. (NEDO)

  10. Report on evaluation of research and development of methods for producing basic chemicals from carbon monoxide and other stocks; Issanka tanso nado wo genryo to suru kiso kagakuhin no seizoho no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-08-01

    This project was aimed at developing methods for producing basic chemicals from carbon monoxide and other stocks (the so-called C1 chemistry), in order to establish the techniques that could promote stable supply of basic chemicals from the new carbon resources in place of oil. It was a 7-year national project beginning in FY 1980, jointly implemented by the government, academic and industrial circles. Described herein are the overall evaluation of the results. There are several carbon resources other than oil, e.g., coal, natural gas, oil shale and tar sand. They are abundantly occurring, although unevenly, and various countries are developing these resources. They can be advantageously utilized as stocks for chemicals, after being converted into synthesis gases. In Japan, they have been efficiently developed cooperatively by national institutes, enterprises, academic circles and chemical industry, to produce the world's results, e.g., gas separation/purification techniques and new catalysts for new synthesis methods. This project was terminated because of the relaxed oil supply/demand situations and lowered crude prices in the middle of the 80's, which made stock conversion less urgent. (NEDO)

  11. Survey on utilization of database for research and development of global environmental industry technology; Chikyu kankyo sangyo gijutsu kenkyu kaihatsu no tame no database nado no riyo ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    To optimize networks and database systems for promotion of the industry technology development contributing to the solution of the global environmental problem, studies are made on reusable information resource and its utilization methods. As reusable information resource, there are external database and network system for researchers` information exchange and for computer use. The external database includes commercial database and academic database. As commercial database, 6 agents and 13 service systems are selected. As academic database, there are NACSIS-IR and the database which is connected with INTERNET in the U.S. These are used in connection with the UNIX academic research network called INTERNET. For connection with INTERNET, a commercial UNIX network service called IIJ which starts service in April 1993 can be used. However, personal computer communication network is used for the time being. 6 figs., 4 tabs.

  12. Fiscal 1999 achievement report. Research and technology of important regional technologies (Development of combustion control system technology for rationalizing energy use); 1999 nendo energy shiyo gorika nensho nado seigyo system gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For upgrading and optimizing combustion control systems, research and development is conducted for materializing SiC devices capable of high-temperature operation. In the development of basic technologies common to various types of SiC semiconductor devices, XeCl excimer laser annealing is applied to SiC implanted with Al ions, and low-damage ion implantation is studied. In the development of techniques for forming SiC single crystals into substrates, warpage of 20{mu} or less, surface coarseness of 5{mu}m or less, etc., are achieved in 1-inch and 2-inch wafers. In the development of SiC sensor technology, techniques of heteroepitaxial growth of 3C-SiC on Si substrates and of 6H-SiC on 6H-SiC wafers are established and an optical sensor is built experimentally. A high-temperature UV sensor, switching device for control, rectification device for control, etc., are built of nitrogen ion implanted 6H-SiC. In the effort to develop combustion control system technology, the principle of system operation of the combustion control method proposed under this project is verified. (NEDO)

  13. FY 1999 report on the results of the technology development for abatement of pollutants related to oil refining; 1999 nendo sekiyu seisei osen busshitsu teigen nado gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The technologies are developed for efficiently, economically improving quality of automobile fuels by, e.g., abatement of environmental pollutants present in the oil products. For improvement of hydrodesulfurization rate of gas oil deep hydrodesulfurization process, the catalyst components high in isomerization ability of the hard-to-desulfurize compounds are investigated, and effectiveness of zeolite is confirmed. For production of low-sulfur gas oil by hydrodesulfurization and hydrocracking of heavy oil, the catalyst with small pores is preferable for desulfurization of gas oil as the co-product of the treatment of heavy oil in the presence of catalyst for heavy oil desulfurization. For hydrocracking, the catalysts are prepared, on a trial basis, for achieving the target gas oil sulfur content of 10ppm or less by optimizing the zeolite and matrix properties. For suitability of gas oil qualities, it is found that the hydrogenation step is the rate-determining step among the reaction routes involved in the hydrogenation of difficult-to-desulfurize compounds. The data of low-sulfur gas oil qualities in Europe are collected. (NEDO)

  14. Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Development of systems for marine organism resources classification and utilization (Achievement report); 1998 nendo kaiyo seibutsu nado shigen no bunrui riyo system no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Genetic resources and databases involving microbes and the like were conserved and amplified for the reinforcement of biotechnology industries. In the maintenance of marine microalga culture collection, 16S rDNA sequences were determined for 120 strains of Cyanophyceae isolated by Marine Biotechnology Institute Co., Ltd., and databases were prepared containing the results of molecule classification, history of each strain, and pictures obtained using optical microscopes. In the maintenance of marine bacterium culture collection, methods for identifying by molecule classification bacteria separated from the sea were simplified and unified, and genera were identified for 776 strains. In the development of systems for classifying and conserving subtropical microbial resources, base sequences were analyzed for 14 strains of six kinds of microbes such as Aspergillus awamori conserved at Institute of Applied Microbiology of University of Tokyo. Other efforts included the enrichment of marine microalga collections, construction of an embryo bank system, advanced classification of microbes, and development of a DNA (deoxyribonucleic acid) analyzing system. (NEDO)

  15. Achievement report for fiscal 1998. Development of control system technologies such as combustion with energy consumption rationalized; 1998 nendo seika hokokusho. Energy shiyo gorkika nensho nado seigyo system gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    To improve and optimize fuel control systems, basic technologies were studied for building SiC devices capable of high-temperature operation. The technologies involved the construction of single-crystal SiC substrates, development of element technologies such as conduction control, experimental production of SiC devices, and systems incorporating SiC devices for controlling, for example, combustion. The subjects of research and development for fiscal 1998 included the technologies related to common SiC semiconductor substrates (SiC substrate crystallinity evaluation by X-ray topography, thermal oxidation acceleration by ion irradiation, and annealing of ion-implanted SiC by excimer laser ), technologies of forming an SiC single crystal into a substrate, technologies related to SiC sensors, technologies related to SiC devices capable of operation at high temperature and high speed, technologies related to SiC devices for controlling, and technologies for controlling, for example, combustion. The subjects of basic researches at universities and research institutes included new crystal growing methods, ion beam-aided SiC synthesis, effect of irradiation of SiC with neutrons, and nuclear conversion implantation. (NEDO)

  16. FY 1999 report on the results of the R and D on the assessment of reliability of oil refining facilities; 1999 nendo sekiyu seisei setsubi shinraisei hyoka nado gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    At present, in oil refineries in Japan, the term of the continued operation in oil refining facilities is shorter than that in Europe and America because of the regulation on the open inspection period for boilers and hazardous material storage tanks. As a result, the refining cost is comparatively higher than in Europe and America due to the increase in inspection/repair cost and decrease in operational rate. Therefore, it is becoming important to effectively supply petroleum products by keeping stability in oil refining facilities of the whole Japan and prolonging the term of the continued operation of oil refining facilities, etc. In this R and D, the technical development is conducted which is needed for the long-term continued operation of oil refining facilities. The items for the R and D are as follows: assessment technology of reliability of oil refining high temperature system facilities, assessment technology of reliability of piping/storage facilities in oil refinery, assessment technology of reliability of oil refining power system facilities, technology of management support system in oil refining facilities. In this fiscal year, technical survey, data collection, and construction of the basic concept of developmental technology were mostly conducted. Also conducted were trial manufacture of various probes for non-fracture inspection use, oscillators, etc., and basic design of inspection equipment and trial manufacture of a part of them. And the data acquired were analyzed. (NEDO)

  17. Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Feasibility study project on liquid fuel conversion); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Ekitai nenryo tenkan kanosei chosa nado jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This article comprises Part 1 on 'surveys of gas fields fit for a new methanol manufacturing process' and Part 2 'reports on overseas surveys of gas fields fit for a new methanol manufacturing process.' In Part 1, surveys are conducted on the existence, exploitation, and the actual utilization of natural gas resources, and on the status of natural gas industry related infrastructures in the Middle East. Proved natural gas reserves in Iran were 742tcf (trillion cubic feet) as of 1996-end, which was the largest in the world next to Russia. As for Kuwaiti natural gas resources, they all accompany oil production, with the proved reserves marking 52.4tcf as of 1996-end or the smallest in the Middle East. In Egypt, there were proved reserves of 20.4tcf as of 1996-end, and further existence of 30-40tcf is predicted. Proved reserves in Yemen are approximately 15tcf. Proved reserves in Oman were 30tcf as of 1996-end. It is expected that there will be a 1.4% increase in the demand for methanol for automobiles. The annual demand for methanol for power generation is 720,000 tons. In Part 2, on-site surveys of infrastructures and the like indispensable for methanol plant installation are reported. (NEDO)

  18. FY 1994 Report on the results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers; 1994 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu saiteki donyu chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Described herein are the FY 1994 results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers or the like. The necessary economic conditions for introduction of a fuel cell system to be competitive with the conventional system which individually supplies electric power and heat are 250,000 yen/kW as the construction unit cost, 0.10m{sup 2}/kW as the installation area, 5 years as the cell body life, use of an inexpensive fuel gas (2 to 6 yen/Mcal). Moreover, it is an indoor system which shall have the operational characteristics to follow daily demand fluctuations while operating under the optimum conditions in the urban redevelopment area considered. A 5,000kW-class fuel cell plant burning fuel gas (2 yen/Mcal) will need a total floor area of approximately 400,000 m{sup 2} in an energy-intensive office type demand area. These conditions shall be met in order to economically introduce the 5,000kW-class plant. It is also necessary to compare the plant with the competitive cogeneration plants. The specifications for the prototype now under consideration are sufficient for the energy-saving effect, and it is premised that these specifications and characteristics are secured. (NEDO)

  19. Report on achievements in fiscal 1999 of New Sunshine Project. Development of superconductor power applied technologies. Research on total system; 1999 nendo chodendo denryoku oyo gijutsu kaihatsu gyomu seika hokokusho. Total system nado no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To deal effectively with problems being actualized in electric power systems, it is necessary to introduce superconductor technologies into power devices, and achieve higher efficiency, density and stability in the power systems. To achieve the goal, development is being made on superconductor power applied technologies, whereas investigative researches are given on the effects of introducing the superconductor power applied devices to proceed the development effectively and smoothly. This project is also given evaluations on its research achievements. In the practical application of superconductor generators, all of the verification tests have been completed, with the model generator system linkage test as the final test. Design and fabrication technologies were established on a 200,000-kW class pilot generator after having gone through analyses made after the tests. Not only having achieved the initial technical value targets, the result presented reliability required for practical use of the superconductor generator, having exceeded the expectation. The research and development of the superconductor generator technologies under this project is concluded successful. The AC superconductor devices were developed by effectively utilizing the results of the leading researches on fundamental technologies for AC superconductor power device technologies as well as other results of the world's highest levels. (NEDO)

  20. Report on evaluation of research and development of methods for producing basic chemicals from carbon monoxide and other stocks; Issanka tanso nado wo genryo to suru kiso kagakuhin no seizoho no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-08-01

    This project was aimed at developing methods for producing basic chemicals from carbon monoxide and other stocks (the so-called C1 chemistry), in order to establish the techniques that could promote stable supply of basic chemicals from the new carbon resources in place of oil. It was a 7-year national project beginning in FY 1980, jointly implemented by the government, academic and industrial circles. Described herein are the overall evaluation of the results. There are several carbon resources other than oil, e.g., coal, natural gas, oil shale and tar sand. They are abundantly occurring, although unevenly, and various countries are developing these resources. They can be advantageously utilized as stocks for chemicals, after being converted into synthesis gases. In Japan, they have been efficiently developed cooperatively by national institutes, enterprises, academic circles and chemical industry, to produce the world's results, e.g., gas separation/purification techniques and new catalysts for new synthesis methods. This project was terminated because of the relaxed oil supply/demand situations and lowered crude prices in the middle of the 80's, which made stock conversion less urgent. (NEDO)

  1. Report on the wind power development field test project in the off-shore park in Daitocho Town in fiscal 1997. System design; 1997 nendo Daitocho kaiyo koen nado ni okeru furyoku kaihatsu field test jigyo hokokusho. System sekkei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    This paper reports the wind power development field test project in the off-shore park in Daitocho Town in Shizuoka Prefecture. The annual average wind velocity was 4.2 m/s (at height of 20 m above the ground), where the facility utilization rates for 300 and 500 kW class plants were 15.1 and 16.7%, respectively. Both of the annual average wind velocity and the facility utilization rate do not meet the criteria established by NEDO. Although the location is adjacent to the Natural Park, there is no restricting condition for installation. The substation to which system linkage is to be performed is the Daito substation 3 km north of the planned location. The major load is the Daito Spa in the park facility. Ground bed at depth of 5 m will be used as the windmill foundation supporting bed. There is little electromagnetic wave hazard. The location is 380 m away from the nearest residential house, presenting no windmill noise problem. The amount of power to be generated was assumed 281,000 kWh. Specifications for nine models of 300-kW class windmills that can be introduced into Japan were discussed to select a model. The project cost was calculated to be 128.5 million yen. The construction cost will be 428,000 yen and the power generation cost 38.1 yen/kWh. Its economy is poor when the current unit price for surplus power purchase is considered, but the effect of enlightenment may be expected. (NEDO)

  2. FY 1998 report on the results of the development in recycling technology for building materials such as waste concrete; 1998 nendo hai concrete nado kenzai recycle gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For increasing fields of application of concrete rubble discharged as construction waste, the recycled aggregate is recovered by heating and rubbing/grinding. To meet the recycling demand effectively, a unit was made a transfer type. Equipment with treatment capacity of 3 tons/h was manufactured and confirmed of its motion. As to the heating equipment, the low-energy consumption structure aiming at homogeneous filling and appropriate ventilation was adopted to control uneven heating and increase in packed bed pressure loss. A tube mill type of the coarse aggregate recovery device was designed/manufactured considering the size of medium and discharge of mortal particles. An attriter type was designed/manufactured considering smooth particle discharge. As to the fine aggregate recovery system, a tube mill type was designed considering the discharge of powder and using coarse aggregate as medium. Moreover, the appropriate transportation of the generated powder and storage method are also considered. The transfer type equipment (unit frame, etc.) was designed/manufactured to make it a unit considered of layout at the time of transporting and assembling the auxiliary equipment such as supply hopper. The noise prevention device was also equipped with. (NEDO)

  3. Fiscal 1998 research report on the development trends of natural gas conversion technologies into liquefied fuel in Russia; 1998 nendo Roshia ni okeru tennen gas no ekitai nenryoka gijutsu no kaihatsu doko nado ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Russia having natural gas resources largest in the world is actively promoting the basic research on liquefaction technology of natural gas such as Fischer-Tropsch (FT) synthetic catalyst, and its research potential is extremely high. This 3-year research project surveys the R and D trends of catalyst technology for liquefaction of natural gas, and fabricates the prototype FT synthetic catalyst based on the idea of Russian researchers to evaluate its feasibility experimentally. This report summarizes the following to clarify the research background: (1) The technology system for liquefaction of natural gas, and its future R and D trend, (2) The R and D trends of liquefaction technology of natural gas in the world, (3) The R and D trends of liquefaction technology of natural gas in Russia, (4) The research system of catalyses in Russia, (5) The activities of Russian catalysis research institutes, (6) The fuel liquefaction technologies of Russian major research institutes, and (7) The proposals from Russian research institutes. (NEDO)

  4. Report on fundamental surveys for such as cases and effects in relation with development of new energy technologies in fiscal 1999; 1999 nendo shin energy gijutsu kaihatsu ni kakawaru jirei koka nado kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the fundamental surveys in fiscal 1999 on cases and effects in relation with development of new energy technologies. Among the projects having been performed by NEDO in commemoration of the 20th anniversary of the NEDO foundation, the economic and social situations in the times in which the projects have been carried out with the focus placed particularly on new energies were put into order and analyzed to make clear the positioning of the project significance in the nation's energy policies. In addition, the roles of NEDO were recognized afresh to use them as the fundamental materials to serve for the future policy development. For the past thirty years before and after the oil crises, the time division that can be used universally for the project evaluation was established, based on the trends inside and outside the country, social currents, related indexes, and the status of development execution. Work hypotheses were presented regarding the basic conception in the evaluation, specific evaluation viewpoints, and their contents. Based on the hypotheses, three subjects were taken up as representative cases, that is, photovoltaic power generation, coal liquefaction, and phosphoric acid type fuel cell technology development. Time points that are considered as the important turning points were specified to give evaluations at respective turning points. Analyses were also made on decision making factors for project planning, continuation, direction change, suspension, and completion. (NEDO)

  5. Survey on actual status of R and D fund assistance in the U.S.A.; Beikoku ni okeru kenkyu kaihatsu shikin enjo no jittai nado ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    As a basic survey to serve for establishment of science and technology policies, a survey was carried out on the actual status of R and D fund assistance in the U.S.A., roles of the government and civil sectors, and how they are interrelated. The survey was performed in detail on the following items: the assistance and cooperation measures taken by the U.S. government, and technological policies of the U.S. government; fund subsidies and policies toward technological research and development provided by the U.S. government; research and development plans and projects being the object of the subsidies given by the U.S. government; assistance and cooperation of private organizations for financing research and development activities in the U.S.A.; cooperation and joint works among industries, the government and universities (research consortiums) in the research and development activities; legal assistance policies for research and development in the U.S.A., the favorable tax system for research and development, the 1984 National Joint Research Act, and the actual status and analysis of the legal assistance policies in the U.S.A. for aiding research and development tests. (NEDO)

  6. Fiscal 1998 research report. Survey on R and D, and application technology of biotechnology; 1998 nendo chosa hokokusho. Bio technology no kenkyu kaihatsu, sangyoka gijutsu nado ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Survey was made mainly on use of biotechnology as resource saving and energy saving processes. Biotechnology is in wide use in a pharmaceutical field, while its application is on the increase in agriculture, food, chemistry, energy and environment fields. The USA is ahead of Japan and Europe. In the USA, there are more than 1000 ventures, and R and D of biotechnology, in particular, gene analysis and manipulation techniques are in progress together with acquisition of patents. In biomass energy, production of ethanol from corn, and development of biodiesel are in progress in the USA and Europe, respectively. Use of biomass should be promoted because of its global environment compatibility and sustainable productivity. In the future bio-market, genome analysis and its application are most important, however, Japan is behind in such technology in the world. The Joint approach by industry, university and government is necessary from the viewpoint of a future marketability and international competitiveness. Promotion of a public acceptance and nurture of creative talents are also important. (NEDO)

  7. Fiscal 2000 achievement report. Development of comprehensive technologies for environmental conservation including prevention of global warming by the carbonization of wood, etc.; 2000 nendo jumoku nado no tanka ni yoru ondanka boshinado fukugo kankyo taisaku gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are exerted to develop new technologies whereby carbon dioxide is absorbed by and fixed in rapidly growing trees. The trees are felled and subjected to high-efficiency carbonization, and the thus-obtained carbonized material is used for environmental purification or the like and then buried in the ground. Studies are under way to find out if the cycle (operations) may be organized into an industry. Activities are conducted in the five fields of (1) carbonized materials, (2) carbonization, (3), industrial use of charcoal, (4) stabilization of charcoal, and (5) reports on surveys (mainly overseas). In field (2), following an introduction consisting of the carbonization mechanism and the definition of terms, surveys are conducted of the existence of carbonizable resources in Japan, distribution channels of imported charcoal and activated charcoal in Japan, various carbonization apparatuses, carbonization equipment incorporated into gasifying fusion furnaces, carbonization furnace as a system, and the trends of development of pyroligneous acid and development of its use. In field (3), studies are made on its use in industries, on its application to agriculture, forestry, and livestock industry, and on the utilization of its electromagnetic properties. (NEDO)

  8. Fiscal 1999 report on results. Development item, 'development of evaluation technique for biocompatibility and the like of porous materials'; 1999 nendo takozairyo no seitai tekigosei nado hyoka gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of establishing fundamental technologies for ceramic porous materials that are excellent for artificial bone for a living body, evaluation technologies were developed for mechanical properties and biocompatibility, with fiscal 1999 results compiled. Performed for the examination of the mechanical properties were flexural test, compression test, tensile test, shearing test, torsion test, fatigue test, etc., with an evaluation testing method studied assuming that ceramic porous materials were applicable to implanting members. In the evaluation of biocompatibility, five kinds of osteoblast-like cell lines were cultured on a plastic disk and a dense hydroxyapatite disk, with adhesion and proliferation of the cells compared. Since these osteoblast-like cell lines adhere and proliferate on the surface and in the pore of hydroxyapatite, evaluation of the biocompatibility such as cell affinity was found possible with this in vitro method. With the view of obtaining principles for designing new bioactive ceramics, a method was developed for evaluating apatite-forming abilities of metal oxide gels having different compositions and structures in simulated body fluid. (NEDO)

  9. FY 1999 report on the results of the R and D of the environmental technology of recycling, etc. 1; 1999 nendo recycle nado kankyo gijutsu kenkyu kaihatsu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing environmental loads of waste and recycling waste, etc., the R and D were carried out, and the FY 1999 results were summarized. In the study of the technology for high-grade recycling of PET bottles, construction work for stabilization of the quality of drainage water was done of a demonstration plant with a treating capacity of 8,000t/y which was constructed in FY 1996, and the stability in long-term operation was examined. In the survey of fluctuations in flake quality, the verification data indicated that the plant could be stably operated. As to the alteration of the bottle cleaning process from wet method to dry method, stabilization of the label separation performance was recognized. By the above-mentioned matters, the technology to recycle/treat PET bottles was established. In the development of the technology to recycle waste plastics which are difficult to treat, assessment was made of the treatment capacity in dry distillation gasification furnace of shredder dust and gasification characteristics. As to the removal of wire harness, separation of glass from fine copper wire, etc., methods which are promising were proposed, and it was concluded that those were not valid as a treatment method in the plant scale in terms of economical efficiency. (NEDO)

  10. Reports on research achievements in developing high-performance industrial furnaces in fiscal 1998 (Research and development of high-performance industrial furnaces). Volume 1; 1998 nendo koseino kogyoro nado ni kansuru kenkyu kaihatsu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    From the reports on research achievements in developing high-performance industrial furnaces in fiscal 1998, the report volume 1 was prepared as a research achievement report of each working group, detailing fundamental researches, heating furnaces, and heat treatment furnaces. The fundamental researches have researched combustion evaluating technology, characteristics of the area in the vicinity of a combustor, characteristics of combustion of high-temperature air, heating characteristics of a furnace to investigate effect of local heat absorption, and combustion evaluation. For the heating furnaces, the following subjects were studied: development of an in-furnace combustion model, summary of an experiment for evaluating high-temperature air combustion, furnace height relative to combustion heat transfer characteristics, heat loss minimizing technology, combustion heat transfer characteristics of liquid fuels, optimal operation of the high-temperature air combustion, basic control in heating control, and steel piece heating control. Studies were performed for the heat treatment furnaces on the case of a direct firing furnace in evaluating the heat transfer characteristics, the case of a radiant tube furnace, application of thermal fluid simulation technology, furnace averaging technology, soot reducing technology, control technology, and trial design on a high-performance heat treatment furnace. (NEDO)

  11. Report on the achievements in the Sunshine Project in fiscal 1987. Collection of data from coal liquefaction processes, and development of a disposal system; 1987 nendo sekitan ekika process nado no data no shushu, shori system nado no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The present study is intended to investigate the current status of the information control system in the coal liquefaction technology development project, and structure a coal liquefaction database system to manage and utilize comprehensively the items of information provided by the system. Section 2 shows the result of epitomizing opinions on the purpose of the coal liquefaction database by means of a questionnaire survey to NEDO, and opinions of people of experience and academic standing. Section 3 depicts the basic conception of a coal database total system. Section 4 summarizes the conceptual idea of the fundamental database by washing out the data input and output, and the contents recorded in the database. Section 5 summarizes the basic sub-system required for management and utilization of the database, and different application systems for data analysis required in each stage of performing the coal liquefaction technology development, and for operation assistance. Section 6 summarizes a general technological information retrieval system, in which general information on coal liquefaction is recorded, processed, and registered and accumulated in the database, and then the information retrieval and the original information providing service are carried out. Section 7 summarizes philosophies on development and operation of the coal liquefaction database, operating institutions, and problems to be solved. (NEDO)

  12. Report on the fiscal 1993 investigational study of the environmental technology development trend in Japan. Trend survey of the introduction policy of environmentally friendly products; 1993 nendo Nippon ni okeru kankyo gijutsu kaihatsu doko nado ni kansuru chosa kenkyu hokokusho. Kankyo chowagata seihin no donyu hosaku nado doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-05-01

    An investigation was conducted into the systematical scheme for the introduction and promotion of environmentally friendly products mostly to the U.S., Europe and China. In the U.S., the introduction policy is given to one and all fields of the industry. The introduction policy of the U.S. has a characteristic that the introduction is left to the market principle by DSM or permit dealing, etc. except the preferential tax system and systematical finance in which the government is concerned. The policy of European countries is characterized by the idea preceding, standards or rules are first given, and the whole is pushed on to them. Accordingly, it seems that there is few atmosphere of expecting to receive the government side economic incentives from the corporate side. Legal regulations on the environment in China were prepared in a comparatively early time (1979), but the supervision of obeying the regulations and the appearance/spread of environmentally friendly product menus have just started. Accordingly, as the introduction policy on environmentally friendly products, there was found nothing valuable but the regulations. 12 refs., 3 figs., 15 tabs.

  13. Report on achievement in researching aids for practical application of recycling technologies in fiscal 1998. Development of a technology to treat hard-to-decompose chemical substances in incineration ash; 1998 nendo recycle gijutsu nado jitsuyoka shien kenkyu seika hokokusho. Shokyakubaichu no nanbunkaisei kagaku busshitsu nado no shori gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper describes development of a technology to decompose dioxins in incineration fly ash. Experiments were carried out during fiscal 1998 by using a bench-scale plant and a laboratory-scale plant of the installed supercritical water treatment equipment designed and fabricated in fiscal 1997. With the bench-scale plant, operation methods were discussed, whereas high temperature and pressure operation of 25 MPa and a temperature internal to the reactor of 350 degrees C were achieved. An alcohol combustion test and a preliminary slurry delivery test were also performed. With the laboratory-scale plant, operating methods were discussed, and combustion tests were carried out by using different organic matters as fuels for the supercritical water oxidation reactor. Investigations were executed on the effects of reactive operation parameters on organic matter decomposition rates, produced gas compositions, and reactor wall temperatures. The intensity of hydrogen bond between solvent and water has decreased to almost half of the normal temperature and pressure water in the vicinity of the critical point. However, strong interaction still remained in terms of per unit density. A portable equipment (650 degrees C and 25 MPa at the maximum, and standard treatment quantity of dry fly ash of 1 kg/h) was operated for demonstration. Operation methods and organic matter decomposition characteristics were identified in alcohol operation and slurry operation. (NEDO)

  14. Report on the achievements in the Sunshine Project in fiscal 1988. Development of a collection and processing system for data of the coal liquefaction process; 1988 nendo sekitan ekika process nado no data no shushu, shori system nado no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    Storing and managing comprehensively a huge amount of data acquired in developing the coal liquefaction technologies would greatly contribute to moving forward the development of the coal liquefaction technologies, and realizing a commercial plant being the ultimate goal. It is intended to investigate the current status of information management systems used for development projects being implemented or planned in developing the coal liquefaction technologies. It is also intended to structure a coal liquefaction database system to utilize comprehensively and effective the information discovered by the above investigation. The current fiscal year has performed developments on the following items to structure a coal liquefaction database system by using a computer: (1) conceptual design of the fundamental database, and (2) basic design on a general technological information retrieval system. The development during the current fiscal year established a method to classify levels of data accommodation for the fundamental database based on the investigation and analysis of the experimental data. In addition, with regard to the general technological information retrieval system, summarization was performed on the specifications of the hardware and software, the basic configuration, the input and output specifications, and the retrieval screens. (NEDO)

  15. FY 1999 report on the results of the superconductive energy application technology development/research on a total system, etc. Survey of potentiality of the commercialization of superconductive technology, effects of the introduction, etc. (Future course of the superconductive technology development in Japan); 1999 nendo chodendo denryoku oryokuyo gijutsu kaihatsu total system nado no kenkyu. Chodendo gijutsu no jitsuyoka kanosei oyobi donyu koka nado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    By the use of superconductive technology, the following are aimed at: marked reduction in power loss of electrical equipment and power transmission path, and size/weight reduction in electrical devices by high current/magnetic flux density. The superconductive technology has advantages such as great energy saving effect, CO2 reduction and global environmental preservation. As an example, concerning the superconductive generator now being developed under the New Sunshine Project, power loss can be reduced by half, and by the use of high magnetic field, size/weight can be reduced such as reduction in rotor diameter and reduction in weight by half. Further, as an innovative system, cited are the superconducting magnetic energy storage system (SMES) and flywheel energy storage system. The superconducting magnetic levitation railway, medical use MRI, etc. have also innovativity which is difficult to get in the conventional technology. Effects are also expected of introducing the process development using superconducting magnet such as magnetic separation, electromagnetic metallurgy, electromagnetic agitation and monocrytal growth convection control. Also cited is Josephson electronic device. High performance SQUID in bio-magnetic/non-destructive inspection is also expected to be developed. (NEDO)

  16. FY 2000 report on the results of the technology development of energy use reduction of machine tools, etc. Technology development of environmental load reduction related to water soluble lubricating oil, etc. (R and D of low energy coolant degradation prevention technology and waste liquid processing technology); 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Suiyosei junkatsuyu ni kakawaru kankyo fuka teigen nado gijutsu kanri (tei energy coolant fuhai boshi gijutsu oyobi haieki shori gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D were carried out on a system by which the long life of coolant of machine tools can be achieved and a system to process waste efficiently, economically and with less environmental loads, and the FY 2000 results were summed up. In the R and D of a system to prevent degradation of low energy coolant, measurement was made of effects of the degradation prevention system at a laboratory level, and it was found out that propagation of bacteria causing the degradation can be prevented with pH kept high. Further, it was admitted that the alkali effect on metal formability was not very much. As to the coolant processing, in the present situation, most of the coolant is taken back by industrial waste processing dealers. So, the development of the low energy waste liquid processing system is earnestly desired. In the R and D of the low energy waste liquid processing system, test on characteristics evaluation was conducted about each method of systems. Subjects to be improved/solved were extracted such as the point that volatile organic matters are included in condensed water after evaporation of waste liquid and there seems to be a possibility of needing the secondary processing. (NEDO)

  17. Fiscal 1998 R and D project on global environmental industrial technology. Research result report on DNA analysis and information processing technology for photosynthesis microorganisms (Development of CO{sub 2} fixation and effective use technology by using bacteria and algae); 1998 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Kogosei biseibutsu nado DNA kaiseki joho shori gijutsu no kenkyu (saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes the fiscal 1998 research result on DNA analysis and information processing technology for photosynthesis microorganisms. On the study on DNA analysis technology by triple-strand formation method, as the comparison study result of a READ method, stable triple- strand formation method and hairpin method, a READ method showed the highest triple-strand formation efficiency for target DNA. On the study on accurate separation technology of specific genes, establishment of protocols was promoted for solid-phase probe technology, subtract technology and leveling technology. On the study on DNA microarray analysis technology by high-efficiency hybridization method, the analysis technology of genes by hybridization method using DNA chips is under investigation. In addition, the high- efficiency analysis technology of specific DNA segments by using an affinity sensor, and the high-accuracy cloning technology for DNA with altered primary structure were also studied. (NEDO)

  18. Fiscal 1997 R an D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (high-efficiency and analysis and manipulation technology for DNA); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Through the observation of super spiral DNA fixed on a spermin or spermidine treated mica substrate by AFM (atomic force microscope), fixation of DNA without any deformation in solution was clarified, and visualization of the spiral structure of DNA were successfully achieved. Manipulation of Xe atoms adsorbed on an Si(111) surface was certainly possible by using STM (scanning tunneling microscope)/atom probe equipment. A nucleation mechanism in crystal growth was studied for various organic source-molecules/GaAs(001) surface systems, and formation of high-density nuclei on the GaAs surface was achieved by accelerating the translational energy of Ga material molecules up to 6eV or more. Ziegler- Natta catalysis important for industrial polymerization of olefin molecules was precisely analyzed by first-principle dynamic simulation. A large-scale simulation of zeolite catalyst is also in promotion for methanol to gasoline conversion. 51 refs., 87 figs., 7 tabs.

  19. FY 2000 research and development of fundamental technologies for AC superconducting power devices. R and D of fundamental technologies for superconducting power cables and faults current limiters, R and D of superconducting magnets for power applications, and study on the total systems and related subjects; 2000 nendo koryu chodendo denryoku kiki kiban gijutsu kenkyu kaihatsu seika hokokusho. Chodendo soden cable kiban gijutsu no kenkyu kaihatsu, chodendo genryuki kiban gijutsu no kenkyu kaihatsu, denryokuyo chodendo magnet no kenkyu kaihatsu, total system nado no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The project for research and development of fundamental technologies for AC superconducting power devices has been started, and the FY 2000 results are reported. The R and D of fundamental technologies for superconducting power cables include grasping the mechanical characteristics associated with integration necessary for fabrication of large current capacity and long cables; development of barrier cable materials by various methods; and development of short insulated tubes as cooling technology for long superconducting cables, and grasping its thermal/mechanical characteristics. The R and D of faults current limiters include introduction of the unit for superconducting film fabrication, determination of the structures and layouts for large currents, and improvement of performance of each device for high voltages. R and D of superconducting magnets for power applications include grasping the fundamental characteristics of insulation at cryogenic temperature, completion of the insulation designs for high voltage/current lead bushing, and development of prototype sub-cooled nitrogen cooling unit for cooling each AC power device. Study on the total systems and related subjects include analysis for stabilization of the group model systems, to confirm improved voltage stability when the superconducting cable is in service. (NEDO)

  20. FY 1998 annual report on the preliminary research and development of techniques for developing resources from gas-hydrate. Studies on gas-hydrate exploration, excavation techniques, methods for assessing environmental impacts, and gas hydrate handling systems; 1998 nendo gas hydrate shigenka gijutsu sendoken kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no kenkyu kaihatsu, riyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This R and D project is for the preliminary studies on development of the following 4 types of techniques for developing resources from gas-hydrates (GH): (1) gas-hydrate exploration, (2) excavation techniques, (3) methods for assessing environmental impacts, and (4) gas hydrate handling systems. The FY 1988 R and D results are described. For gas-hydrate exploration, the methods for analyzing inorganic ions and trace quantities of elements, which are necessary for accurately estimating the offshore GH around Japan, are established; and case studies are conducted for methods of predicting GH deposit forming mechanisms, and stability fields of GH, based on terrestrial heat flow and seismic data. For excavation techniques, GH decomposition rate is analyzed using a laboratory system which reproduces conditions of excavation of GH layers. For methods for assessing environmental impacts, a geo-hazard predicting model is established, to study ground displacement and gas leakage sensing systems and data transmission systems to cope with the hazards. For gas hydrate handling systems, an overall system is studied, and storage and transportation systems are outlined. (NEDO)

  1. NEDO Forum 2001. Session on development of geothermal energy (Prospect of geothermal energy); NEDO Forum 2001. Chinetsu kaihatsu session (chinetsu energy no tenbo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-20

    The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Director Noda of Institute for Geo-Resources and Environment, National Institute of Advanced Industrial Science and Technology, delivered a lecture entitled 'Future course of geothermal technology development,' and Executive Director Iikura of Tokyo Toshi Kaihatsu, Inc., a lecture entitled 'Thinking of geothermal energy.' Described in an achievement report entitled 'Present state and future trend of geothermal development' were the present state of geothermal power generation and characteristics of geothermal energy, signification of the introduction of binary cycle power generation, and the promotion of the introduction of ground heat utilizing heat pump systems. Stated in a lecture entitled 'Geothermal development promotion survey' were the geothermal development promotion survey and its result and how to implement such surveys in the future. Reported in a lecture entitled 'Verification survey of geothermal energy probing technology and the like and the development of geothermal water utilizing power plant and the like' were reservoir fluctuation probing, deep-seated thermal resource probing and collecting, 10-MW class demonstration plant, Measurement While Drilling System, and a hot rock power generation system. (NEDO)

  2. Comparación de los efectos del D-004, imipramina y sertralina en el modelo de nado forzado en ratones Comparative effects of D-004, Imipramine and Sertraline in the forced swimming test in mice

    Directory of Open Access Journals (Sweden)

    Daisy Carbajal Quintana

    2012-09-01

    Full Text Available Introducción: La finasterida, inhibidor de la 5 a-reductasa, se emplea en el tratamiento de la hiperplasia prostática benigna, y ocasiona entre sus efectos adversos un aumento de cuadros de depresión. El D-004 es un extracto lipídico extraído a partir del fruto de la palma real (Roystonea regia, inhibe la 5 a-reductasa y previene la hiperplasia prostática benigna, y muestra un efecto antidepresivo moderado en el ensayo de nado forzado y suspensión por la cola. Objetivo: comparar el efecto del D-004 con la imipramina y la sertralina sobre la duración de las conductas de inmovilidad, nado y escalado en el ensayo de nado forzado. Métodos: se distribuyeron los ratones en ocho grupos: control (vehículo, tres tratados con D-004 (100, 250 y 500 mg/kg, dos con sertralina y dos con imipramina (30 y 50 mg/kg respectivamente. Estos se colocaron en un cilindro de cristal que contenía agua a una altura de 6 cm y se cuantificaron las conductas. Resultados: la administración oral de D-004 (100, 250 y 500 mg/kg durante 14 días redujo significativamente el tiempo de inmovilidad con respecto al grupo control (17, 22 y 25 % y aumentó significativamente la conducta de nado en 1,58, 1,68 y 1,74 veces. Este efecto resulta moderado (25 % comparado con las reducciones alcanzadas por la sertralina y la imipramina (³ 60 %. Las dosis mayores (250 y 500 mg/kg ocasionaron incrementos de la conducta de escalado, 2,79 y 3,55 veces superiores a la del grupo control, lo que mostró semejanza con la imipramina, aunque con una menor eficacia. Conclusiones: el D-004 ejerce un moderado efecto antidepresivo, lo que pudiera contribuir al manejo de los pacientes con hiperplasia prostática benigna en los cuales se informa coincidencia de cuadros depresivos.Introduction: Finasteride is a 5 a-reductase inhibitor to treat benign prostatic hyperplasia (BPH and one of the adverse effects is the increase of depressive symptoms. D-004 is a lipid extract from the real palm

  3. Desempenho e pacing na prova de 200 m nado borboleta: variabilidade e relações dos tempos parciais de 50 m com o tempo final

    Directory of Open Access Journals (Sweden)

    F.A. de Souza Castro

    2017-12-01

    Full Text Available Resumo: Objetivo: Analisar o desempenho e o pacing de prova dos semifinalistas da prova de 200 m nado borboleta do 15.° Campeonato Mundial de Natação da Federação Internacional de Natação (FINA. Método: Os dados foram obtidos da página eletrônica da FINA. Os 32 tempos da etapa semifinal, masculina e feminina, foram divididos em 4 grupos: 8 homens classificados para a final (G1M, 8 homens não classificados (G2M, 8 mulheres classificadas para a final (G1F e as 8 mulheres não classificadas (G2F. A velocidade de nado, para cada parcial de 50 m, foi estimada pelo quociente entre 50 m e o respectivo tempo. Foram calculados os coeficientes de variação de tempo das 4 parciais de 50 m e comparados entre os grupos (ANOVA. Tamanho de efeito foi verificado com d de Cohen. Correlacionou‐se o desempenho (tempo total com o tempo de cada parcial de 50 m (r de Pearson. Resultados: O coeficiente de variação para as parciais de 50 m foi menor nos grupos dos finalistas de ambos os sexos (G1M e G1F e menor para as mulheres. A terceira parcial de 50 m apresentou maior correlação com o desempenho final em ambos os sexos. A velocidade média caiu ao longo da prova em ambos os grupos. Conclusão: O pacing para o melhor desempenho na prova é evitar variações de tempo ao longo dos 200 m nado borboleta e os treinamentos devem ser direcionados ao aprimoramento condicionante dessa parcial (150‐200 m. Resumen: Objetivo: Analizar el desempeño y pacing durante la prueba de semifinalistas de 200 m mariposa del 15.° Campeonato Mundial de Natación de la Federación Internacional de Natación (FINA. Método: Los datos fueron retirados de la página electrónica de la FINA. Los 32 tiempos de la semifinal masculina y femenina fueron divididos en cuatro grupos: ocho varones clasificados para el final de la prueba analizada (G1M, ocho varones no clasificados (G2

  4. Fiscal 1997 industrial technology R and D project. Research report on development of use technology of bio- resources such as complex biosystem (Development of use and production technologies of complex biosystems); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This project aims to establish production technology of functional substances, oil degradation and purification technology, and use technology of unused oil fraction through development of cultivation control technology of complex biosystems. For functional material production technology, as functional substances some specific marine bacteria inhibitors, antibreeding substances of microalgae, and UV absorption substances were isolated. The productivity of korormicin as specific inhibitor against marine bacteria was improved considerably by cultivation method. For research on molecular genetic analysis technology, a new identification technology and a simple automatic analysis system of microeucaryotes using genes were developed. For global environment purification technology such as efficient degradation of pollutants, study was made on cultivation control technology of phenol- degrading consortia, population dynamics of oil-degrading microbial consortia and a restoration method of oil pollution by complex biosystem at lower temperature, and the demonstration experiment of oil degradation were carried out. (NEDO)

  5. FY 1998 report on the verification survey of geothermal survey technology, etc./Development of the reservoir fluctuation survey method (Summary). Theme 3. Development of the electric/electromagnetic survey method; 1998 nendo chinetsu tansa gijutsu nado kensho chosa choryuso hendo tansaho kaihatsu hokokusho (yoyaku). 3. Denki denjiki tansaho kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Three observation wells were drilled in the Ogiri experimental field. The depth of drilling was 101-120m. In the self-potential observation, admitted were fluctuations, etc. caused by daily changes (tidal changes and earth current), earth current by external magnetic field induction, well drilling noise and injection well. In the resistivity structure survey, the whole area indicated a three-layer (high/low/high) structure, and the shallow high-resistivity layer was correspondent with the new unaltered volcanic rock, and the medium-depth low-resistivity layer with the clayey alteration. On the assumption that the reservoir model is improved by properties of geothermal water and 35% of the returning geothermal water goes back to the production region, pressure/chlorine concentration were satisfactorily explained. Changes in chlorine concentration by the returning geothermal water are estimated at 22% within production reservoir and at 52% in injection region, and when considering temperature changes, it was predicted that fluctuations of the resistivity underground are within 20%. The accuracy of the MT method was studied by using the MT method with the existing MT method. The accuracy was not enough to detect a resistivity of 10%, and therefore, the repeated measurement by fixed electrode or the continued MT method monitoring is needed. (NEDO)

  6. Achievement report for fiscal 1996 on the research and development of technologies for important region. Development of control system technology for combustion with energy use rationalized, etc.; 1996 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika nensho nado seigyo system gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The goal is to develop basic technologies to build an SiC device capable of service amid high-temperature surroundings for the advancement and optimization of combustion control systems. In an SiC semiconductor, the Si-C bond is broken when irradiated with ions, and this makes the occurrence of thermal oxidation easy to occur. In the study to form SiC into single-crystal substrates, a substrate with warpage of 10 micrometers or less and surface coarseness of 10 nanometers or less is realized. In the development of sensor technologies, the high-speed CVD (chemical vapor deposition) method is applied for the growth of crystals further on a 3C-SiC layer epitaxially grown by MBE (molecular beam epitaxy) surface control, which improves on layer characteristics. Element technologies are developed for the construction of a 3-terminal element (FET: field effect transistor), which is for the construction of a high-temperature, high-speed SiC device. An effort is made at achieving 3C-SiC hetero-epitaxial growth, etc., on a 3-inch Si substrate using an SiC crystal film formation experimenting apparatus, which aims at constructing a control device. Concerning the combustion control system, the relations between the air/fuel ratio and the emission spectra of radicals OH, CH, and C2 in a flame are made clear. Also referred to are the basic studies being conducted at research institutes such as universities and a survey of technological trends abroad.

  7. Fiscal 1997 research report on development of use technology of bio-resources such as complex biosystem (Development of use and production technologies of complex biosystems); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho (fukugo seibutsukei riyo seisan gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This report summarizes the fiscal 1997 research results on production technology of functional materials, and the research study result for utilizing substance production and decomposition by complex biosystem for industries. For detecting technique of microorganisms in soil, staining by CFDA-AM was suitable, and allowed visualization of sulfate- reducing bacteria during culture. For research on functional analysis technology, study was made on atomic force microscope technology to detect microorganisms in environment and observe their fine structures. For research on detection, separation and cultivation technology of difficult-to-culture microorganisms, a molecular genetic analysis method of microbial communities and a determination method of their viability were selected. For functional substance production technology, study was made on technical utilization of bioflocculant produced by microbial consortia as environment-friendly oil removal reagent, and on gene transfer control in microbial consortia. For the research study for the project, survey was made on useful substances produced by complex biosystem. (NEDO)

  8. Fiscal 1999 research and verification of geothermal energy exploring technologies and the like. Development of reservoir mass and heat flow characterization (Electrical and electromagnetic monitoring technology - Summary); 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho (yoyaku). Choryuso hendo tansaho kaihatsu (denki denjiki tansaho kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Facilities for monitoring self-potential and resistivity are installed in the Ogiri district, Kagoshima Prefecture, where the Ogiri geothermal power plant is situated, and studies are made about relations between hot water production/reinjection and potential/resistivity at the power plant for the development of a high-performance numerical simulation system for the reservoir. The activities cover the development of (1) a self-potential monitoring system, (2) the development of a resistivity monitoring system, and (3) the development of a reservoir change prediction technique using self-potential and resistivity. Under item (1), eight self-potential monitoring stations are newly installed for the monitoring effort to continue now at a total of 50 stations. Potential has risen by 20 mV in two years since the drilling of a production replenishment well in February of 1999, with the domain of change in potential also expanding. Under item (2), the 3D MT (3-dimensional magnetotelluric) technique is used for resistivity profile investigation at 80 monitoring stations and preliminary monitoring tests are conducted to deliberate positions for resistivity monitoring. Under item (3), tracer tests are conducted for constructing a high-precision reservoir model for predicting changes in temperature, etc., attributable to the return of reinjected hot water, and a natural state reservoir simulation model is fabricated. (NEDO)

  9. Fiscal 1999 achievement report. Development of technology for machine tool with energy consumption rationalized (Research and development of environment-conscious grinding system); 1999 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Kankyo taiogata kensaku kako system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A large quantity of coolant is used in the grinding process for ensuring high accuracy and quality in the work. This presents a serious problem from the viewpoint of environmental impact or energy conservation, and now environment-conscious grinding methods requiring no or less coolant are sought for. With a view to answering the demand, efforts are exerted to put to practical use, and improve, an EcoloG grinding technique. The goal is to reduce to half the energy that the grinding process is now consuming. The EcoloG technique is a grinding method under which vegetable oil mist is cooled for lubrication and a small amount of cooling water is fed to the point of grinding for removing chips. In fiscal 1999, a survey was conducted on technical literature, patents, and the like in and out of Japan for the study of the actual state of dry machining, and then the course of future studies was clearly established. Studies were also carried out aiming at the practical application and improvement of the EcoloG grinding technique, and the technique achieved a quality level as high as that of the conventional coolant-aided method in a process of grinding a shaft to have an accurate outer diameter by use of an ordinary wheel head. (NEDO)

  10. FY 1999 Report on research and development of energy utilization rationalization superhigh-technological liquid crystal technologies. Superhigh-technological electronic technology development promotion project for new functional electronic material design, control and analysis technologies; 1999 nendo energy shiyo gorika chosentan ekisho gijutsu kaihatsu seika hokokusho. Chosentan denshi gijutsu kaihatsu sokushin jigyo shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-04-01

    Described herein are the FY 1999 results of the liquid crystal technology development project. For the researches on multi-layer reflection, composite panels of flattened resins of different refractive index are developed to improve 2-layer monochromic contrast ratio. The guest/host liquid crystal compositions of high orientation order are investigated as the those useful for high contrast. Compounds are pursued for superanisotropic light absorption, and modification with a substituent is found to be effective. Molecular orientation controlling is also studied. For researches on memory-sustaining type liquid crystals, the studied items include formation of thin ferroelectric films on glass substrates, improvement of voltage-sustaining characteristics by composites (including compounds), and doping of trace quantities of ionic impurities. For development of image element colors, the studied items include multi-lattice-structured, oriented HPDLC devices, composites of high birefringence (high order light scattering), and light interference, high order light scattering type light control devices. The multi-dimensionally anisotropic structure of configuration divided into 3 parts of R, G and B is developed to create directive reflection which improves brightness of the reflection type color liquid crystal. A group of compounds are pursued to develop liquid crystal compositions of high refractive index anisotropy, and promising ones are found. The results of the comprehensive investigations are also described. (NEDO)

  11. Fiscal 2000 research achievement report on the development of super-advanced liquid crystal technology for energy use rationalization. Development promotion project for super-advanced electronic technology - Design, control, analysis, etc., of electronic materials having novel functions; 2000 nendo energy shiyo gorika chosentan ekisho gijutsu kaihatsu seika hokokusho. Chosentan denshi gijutsu kaihatsu sokushin jigyo (shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-04-01

    Efforts are focused on the verification of target devices under the respective subjects, and activities are conducted with the development system reinforced. Three newly proposed reflection type liquid crystal devices achieve the target specifications of a reflection factor of 60% or higher and a contrast ratio of 15:1 or higher. Studies are conducted involving the five fields of (1) multilayer reflection devices, (2) memory retention liquid crystal devices, (3) single pixel color devices, (4) directional reflection devices, and (5) joint research. Research and development in field (1) covers ultra-anisotropic optical materials, ultrahigh reliability host liquid crystal materials for guest-host liquid crystals - mixed system, low voltage driven/high load holding liquid crystal compound systems, and new liquid crystal molecule orientation control technology; in field (2), low temperature fabrication of ferroelectric thin film, and ultrahigh purity high reliability liquid crystal compounds; in field (3), materials capable of controlling optical interference and higher order light scattering, photoregulation devices, highly birefringent liquid crystal materials - mixed system, and ultrahigh efficiency light scattering liquid crystal compounds; and, in field (4), multi-dimensional anisotropic structure fabrication technology and ultra-anisotropic optical materials. (NEDO)

  12. Fiscal 1997 report on the survey of verification of geothermal exploration technology, etc. 1. Development of the reservoir variation exploration method (development of the fracture hydraulic exploration method); 1997 nendo chinetsu tansa gijutsu nado kensho chosa. Choryuso hendo tansaho kaihatsu (danretsu suiri tansaho kaihatsu) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the fiscal 1997 result of the fracture hydraulic exploration method as the variation exploration method of geothermal reservoirs. By elucidating hydraulic characteristics of the fracture system forming reservoir, technologies are established which are effective for the reservoir evaluation in early stages of development, maintenance of stable power after operational start-up, and extraction of peripheral reservoirs. As for the pressure transient test method, a test supporting system was basically designed to obtain high accuracy hydraulic parameters. As to the tiltmeter fracture monitoring method, a simulation was made for distribution of active fractures and evaluation of hydraulic constants without drilling wells. In relation to the two-phase flow measuring method, for stable steam production, the use of the orifice plate, the existing flow measuring method, etc. was forecast as a simple measuring method of the two-phase state of reservoir. Concerning the hydrophone VSP method, a feasibility study was made of the practical VSP for high temperature which can analyze hydraulic characteristics and geological structures around the well at the same time which the existing methods were unable to grasp, and brought the results. Moreover, to make high accuracy reservoir modeling possible, Doppler borehole televiewer was made in each reservoir. 80 refs., 147 figs., 22 tabs.

  13. Fiscal 1997 Project related to research and development of global environment industrial technologies. Report on the results of works commissioned for research and development of technology for reducing carbon dioxide emissions; 1997 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu kanren jigyo. Nisanka tanso nado haishutsu teigen gijutsu kenkyu kaihatsu itaku gyomu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    With an objective of achieving reduction in emission of carbon dioxide and fluorocarbons, the `research and development on technologies to reduce emission of carbon dioxide and other substances` consisting of eight projects were conducted. In research and development of waste water treatment technologies using submerged combustion, studies were performed on removal by combustion of such pollutants as organic compounds, nitrogen compounds, and sulfur compounds. The development targets were achieved on each item. In research and development related with thermal electric power generation elements, semiconductor single crystals were fabricated in order to acquire technical knowledge on thermal power generation elements intended of utilizing industrial waste heat, whereas a simulation technology for designing was developed. In other projects, research and development works were carried out on high-performance heat insulating materials, and a movable methanol reformer for fuel cells. Developments were conducted on a large pressure reducing valve, and a cooling and heating turbo heat pump for regional air conditioning facilities. Research and development were made on Peltier elements, all efforts having achieved results respectively. 134 figs., 65 tabs.

  14. Research achievement report for fiscal 1998 on the development of high-performance industrial furnaces. Research and development of high-performance industrial furnaces and the like (2); 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu (2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Volume 2 named above contains part of research achievement reports and individual research achievement reports. The aluminum melting furnace working group research achievement report covers aluminum melting furnace operating patterns, concentrated impinging flame mode and dispersed impinging flame mode, and honeycomb and ball structures in heat storing bodies. The tubular heater working group report mentions the application of this facility to oil heating furnaces, studies and investigations for the embodiment of real systems using the tubular heater, and tests conducted in a furnace with plural heating tube lines. The individual research achievement reports elaborate on the development of technologies of heat transfer optimization under unsteady conditions in the steel material heating process, research and development of high-efficiency heat transfer technologies, development of heating furnace geometry optimization technologies, research and development of a high-performance controlled atmosphere heat treatment furnace, development of high-efficiency heat transfer technologies in high-temperature jet flame heating, development of heat uniformity improvement technologies for example for the steel material heating process, construction of optimum combustion control technologies for the regenerative burner furnace, research concerning laser-aided measurement in industrial furnaces, etc. (NEDO)

  15. Achievement report for fiscal 1997 on the development of technologies for utilizing biological resources such as complex biosystems. Development of complex biosystem analyzing technology; 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei kaiseki gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The aim is to utilize the sophisticated functions of complex biosystems. In the research and development of technologies for effectively utilizing unexploited resources and substances such as seeweeds and algae, seaweeds are added to seawater to turn into a microbial suspension after the passage of two weeks, the suspension is next scattered on a carageenan culture medium, and then carageenan decomposing microbes are obtained. In the research and development of technologies for utilizing microbe/fauna-flora complex systems, technologies for exploring and analyzing microbes are studied. For this purpose, 48 kinds of sponges and 300 kinds of bacteria symbiotic with the sponges are sampled in Malaysia. Out of them, 15 exhibit enzyme inhibition and Artemia salina lethality activities. In the development of technologies for analyzing the functions of microbes engaged in the production of useful resources and substances for animals and plants, 150 kinds of micro-algae are subjected to screening using protease and chitinase inhibiting activities as the indexes, and it is found that an extract of Isochrysis galbana displays an intense inhibitory activity. The alga is cultured in quantities, the active component is isolated from 20g of dried alga, and its constitution is determined. (NEDO)

  16. Development in fiscal 1998 of technology to put solar systems for industrial use into practical use. International joint technology development for solar energy utilization systems; 1998 nendo sangyoyo nado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The solar energy utilizing technologies having been developed under the Sunshine Project were used to have executed the international joint technology development on the 'solar heat utilizing drying system' in the Republic of Indonesia. This paper summarizes the achievements in fiscal 1998. In operating the pilot plant, three operational experiments out of seven experiments were carried out only by Indonesian engineers. As a result of the drying experiments, the heat collecting characteristics of the collector were as about half at 19 to 30% as the efficiency assumed in the design of 50%. The reason for this can be attributed to the fact that the cover glass used in the demonstration test in Japan had light permeability of about 87%, but the cover glass used in the test plant was made of frosted glass whose light permeability was about 37%. This glass is the only glass available for a heat collector in the solar heat hot water device in Indonesia, but is unsuitable for the heat collector. Another cause was that the insolation at the site was lower by about 30% than the one used at the design stage. (NEDO)

  17. Hydrogen utilization international clean energy system technology (WE-NET). Subtask 8. Development of hydrogen combustion turbines (development of the main component devices such as turbine blades and rotors); Suiso riyo kokusai clean energy system gijutsu (WE-NET). Subtask 8. Suiso nensho turbine no kaihatsu (turbine yoku, rotor nado shuyo kosei kiki no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper described the result of the fiscal 1996 development relating to hydrogen combustion turbines, as one of the hydrogen utilization technologies, which have excellent environmentality and are expected of remarkably high efficiency. In the film cooling system of first-stage moving/stationary blades, the smaller the pitch of film pore is, the higher the mean cooling efficiency becomes, indicating 0.7 at maximum. As compared with the conventional shower head type, the metal temperature can be reduced 30-40degC. In the recovery type inner (convection) cooling system, by reducing the blade number, the consumption amount of coolant can be reduced 6% in stationary blade and 13% in moving blade, as compared with the result of the preceding year. In the element test of the hybrid cooling system, film cooling efficiency was actually measured by the porous module test equipment, and the result well agreed with the calculation result. In the water cooling system, studied were water (stationary blade) and vapor (moving blade) of the closed cooling structure for realization of a cycle efficiency of 60%. In rotor/disk cooling, analyses were made of seal characteristic grasp tests and characteristics of the rotor. The effect of deflection in the mainstream was small. Besides, proper value of the seal overlapping amount could be obtained. 6 refs., 368 figs., 55 tabs.

  18. FY 2000 report on the results of the technology development of energy use reduced machine tools, etc. Development of the linear motor system for realization of energy conservation and commercialization; 2000 nendo energy shiyo gorika kosaku kiki nado gijutsu kaihatsu seika hokokusho. Shoeneka to jitsuyoka wo jitsugensuru linear motor system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In relation to the drive system of machine tools widely used as production facilities for automobiles, home electric appliances, etc., the R and D were made of a high efficiency linear motor system of which attention was paid to energy rationalization and environmental loads, and the FY 2000 results were summed up. In the study of the development of the system, studies were made not only on the lowering of heating, cost reduction and heightening of speed, but on the mechanism and control by which machine natural vibration can relatively be cut off, technology of damping for cutting vibration, technology to meet the deformation, etc. by cutting loads, sliding loads, and acceleration of accelerating/decelerating, technology to reduce the machine weight, etc. In the study of the basic technology of linear motor, the finite element method analysis was conducted on the typical linear motor. Concerning the control system, specs were studied which can deal with natural vibration and cutting vibration of the machine system. As to the development of the steel scale type linear encoder, scale sample for evaluation of basic characteristics was designed/trially manufactured. In the study of the detection optical system, the design/trial manufacture of photodiode array were made. (NEDO)

  19. Fiscal 1994 report on technological results. Development of fuel cell technology such as urban energy center (Survey for practical development of optical system of decentralized power source for residential use); 1994 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu seika hokokusho. Minseiyo bunsangata dengen saiteki system jitsuyoka kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Feasibility study was conducted on the technology for practical application of a several kW class fuel cell for the people's livelihood, particularly, for residential use. The study was made in six areas consisting of study on the present state of technology, conceptual design of a small fuel cell, survey on a promising market, basic concept of cell for residential use, feasibility study on application and on introduction. There is no record of development of the several kW class; while the fuel cell excels in the efficiency of energy utilization and the environmental conservation, its performance greatly deteriorates by start and stop under the present technology. Accordingly, it is a prerequisite that the equipment is for an electric heat combined type and for system interconnection. Also, while it is proper that the cell is phosphate type and that the fuel is natural gas, an innovation is necessary in the technology for reforming the cell and the fuel. The conceptual design revealed the possibility of a power generation system having a generating efficiency of 32%, exhaust heat recovery rate of 30%, and dimension of 75x65x150 cm. On the basis of a feasibility study on the application to the combination of a house and a beauty parlor, an advantage was recognized in the fuel unit cost of 5 yen/meal and the equipment cost of 200-250 thousand yen/kW, with demand estimated for 2.5 million installations nationwide including 950 thousand in natural gas supply districts. (NEDO)

  20. Report on achievements in fiscal 1998. Development of a waste disposal and recycle related technology. (Development of a technology to dispose of air bags adequately); 1998 nendo haikibutsu shori recycle kanren gijutsu kaihatsu air bag tekisei shori gijutsu no kaihatsu nado seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    This technological development is intended to develop a process technology to dispose adequately of air bags convergently when they are removed from waste cars, with consideration paid on environmental and safety aspects. This technology that can dispose of air bags remaining as air bag modules (ABM) in large quantity and adequately can solve the problems of maloperation in opening them in cars and noise in conventional disposal methods. The recovery and disposal system using an inflator can be expected of reducing work load on dismantling contractors and enhancing the work safety. Furthermore, the energy saving process utilizing combustion of plastics can save resources. However, this technology has not elucidated how dioxins, dust, smoke, sulfides, and nitrogen oxides are generated and how the generation can be prevented. Therefore, an exhaust gas dioxin testing facility and an exhaust gas treating facility were installed additionally to the existing heating treatment facility to develop a disposal technology to treat adequately the exhaust gases generated when ABMs are disposed conveergently in large quantity, and treat the waste water discharged from the facilities. Fiscal 1998 has performed preliminary tests to accumulate fundamental data, and design and installation of the above two facilities. (NEDO)

  1. Development in fiscal 1998 of technology to put solar systems for industrial use into practical use. International joint technology development for solar energy utilization systems; 1998 nendo sangyoyo nado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The solar energy utilizing technologies having been developed under the Sunshine Project were used to have executed the international joint technology development on the 'solar heat utilizing drying system' in the Republic of Indonesia. This paper summarizes the achievements in fiscal 1998. In operating the pilot plant, three operational experiments out of seven experiments were carried out only by Indonesian engineers. As a result of the drying experiments, the heat collecting characteristics of the collector were as about half at 19 to 30% as the efficiency assumed in the design of 50%. The reason for this can be attributed to the fact that the cover glass used in the demonstration test in Japan had light permeability of about 87%, but the cover glass used in the test plant was made of frosted glass whose light permeability was about 37%. This glass is the only glass available for a heat collector in the solar heat hot water device in Indonesia, but is unsuitable for the heat collector. Another cause was that the insolation at the site was lower by about 30% than the one used at the design stage. (NEDO)

  2. Report on achievements in fiscal 1999. Development of technology to utilize biological resources such as composite organism systems (development of technology to utilize and produce composite organism systems); 1999 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    It is intended to achieve the following objectives in terms of the technologies to utilize such functions as material production and material decomposition by using composite organism systems: develop a technology to handle the composite organism systems; establish a composite microorganism cultivation control technology, and a composite microorganism system function strengthening technology; develop a technology to separate and cultivate organism groups constituting them, and develop industrial utilization technologies. The fiscal 1999 has discussed developing the elementary technologies for the technology to utilize functions of the composite organism systems on the following research items: 1. a functional material production technology; and 2. comprehensive investigations and researches. In Item 1, development was made on a technology to detect, separate and cultivate microorganisms in soil as the histochemical analytical technology. Development was made on an in situ detection, separation and function analyzing technology for particular composite microorganisms as the function analyzing technology. In the separation and cultivation technology, development was made on a technology to detect, separate and cultivate difficult-to-cultivate microorganisms. In the functional material production technology, development was made on a technology to utilize microbial consortia producing environmentally harmonizing oil-water separating polymers, and a method to execute artificially the gene exchange in the microbial consortia. (NEDO)

  3. FY 1998 report on the results of the development of utilization technology of biological resources such as bioconsortia. Development of the bioconsortia system utilization/production technology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of developing the industrial utilization technology, analysis was made of functions and interactions of the specified functional biological groups, and at the same time the developmental study was made of the technology to isolate/culture the constitutive biological groups. The FY 1998 results were summed up. As to the technology to detect microorganisms in soil, the SFDA method was improved and the new dyeing method was developed. And, there almost was hope for the development. Concerning the functional analysis technology, the functional substances peculiarly manifested only in the complex system in the ocean environment are searched. Several kinds of compounds were found out, and at the same time the test to confirm the biological activity is under way. Relating to the isolation/culture technology, study was made on rotten fruit, and the existence in the sample of the microorganisms which are difficult in isolation/culture was newly confirmed. In regard to the culture of the microorganisms which are difficult in isolation/culture, availability of the replica method was found out. As to the technology to produce functional substances, studies were made on the following: utilization technology of the environmental harmony type oil/water separation polymer producing microbial consortia, method to artificially make gene exchanges in the microbial consortia, etc. (NEDO)

  4. Fiscal 1999 research and verification of geothermal energy exploring technologies and the like. Development of reservoir mass and heat flow characterization (Development of fracture hydrological properties characterization technology - Summary); 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho (yoyaku). Choryuso hendo tansaho kaihatsu (danretsu suiri tansaho kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts are under way to develop reservoir change evaluation technologies to be effective in evaluating reservoirs at their initial stage of development, in stabilizing the output of power stations after their commencement of service operation, and in probing into reservoirs in already-developed areas. One of them concerns the characterization of the hydrological properties of fractures. The development efforts involve (1) a pressure transient test method (measurement of the response of reservoirs to changes in borehole internal pressure), (2) a tiltmeter observation method (ground surface deformation measurement), and (3) a 2-phase flow metering method (metering of spurting fluids). Under item (1), a computer-aided borehole hydrology test system is built and field-tested to isolate problems. Also, a pressure transient test system is built by way of trial by use of which compressor-aided control is performed over air pressure in the borehole. Under item (2), it is made clear that changes, several MPa in scale, in the pressure in a borehole is detected by simulation and that a sufficiently capable system is realized using a tiltmeter available on the market. Under item (3), a device is fabricated which is a combination of a laser flowmeter and a void fraction meter, and a field test is conducted to assess its feasibility and to identify problems. (NEDO)

  5. FY 1999 report on the results of the development of recycling technology of waste architectural materials, glass, etc. Development of the simple glass coloring/decoloring technology; 1999 nendo kenchiku haizai glass nado recycle gijutsu kaihatsu seika hokokusho. Kan'igata glass chakudasshoku gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of increasing the ratio of recycling of waste architectural materials, glass, etc., the development was proceeded with of easy coloring of colorless glass by light irradiation and decoloring of it by heat treatment. The important point for technical development is to develop glass materials which are colored by light and decolored by heat at a level of technique with practicality and to develop coloring/decoloring device. Studies were made in the following three fields: 1) optimization of coloring/decoloring conditions for coloring/decoloring occurring from defects (color centers) under light irradiation; 2) optimization of coloring/decoloring conditions occurring from colorless ions and particulate formation under light irradiation; 3) development of a visible drawing device. In 1), bottle, sheet glass, and soda-lime silicate glass are colored brown by X-ray/UV radiation, but the coloring is bad in stability. However, it was found that the addition of silver oxide improved stability. In 2), it was recognized that when the glass containing a trace of Mn was melted in the reducing atmosphere, it became colorless, and when radiated by X-ray and heat-treated at approximately 200 degrees C, it was colored bluish violet which was vivid and stable. (NEDO)

  6. FY 1998 research result report. Ultra-high liquid crystal technology development for energy use rationalization (Technology of design/control/analysis of new functional electronic materials of the ultra-high electronic technology development promotion project); 1998 nendo kenkyu seika hokokusho. Energy shiyo gorika chosentan ekisho gijutsu kaihatsu (chosentan denshi gijutsu kaihatsu sokushin jigyo shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Element technology is studied to realize a reflective-type, full-color, and high-resolution liquid crystal display for super-low power consumption data display. As to the functional compound microstructure formation technology, a 4-inch panel was trially fabricated using two-layer guest-host liquid crystal technology to achieve the desired display performance by control of molecular orientation. Further, holographic PDLC elements were favorably test-fabricated. A ferroelectric PZT thin layer was formed by forming layer at low temperature at which a glass substrate can be used. Optical interference/optical dispersion type optical control materials were studied by liquid crystal/polymer composition. Also studied were super-pure/super-reliable liquid crystal compound/liquid crystal composite systems and super-anisotropic liquid crystal compound by modeling ionic impurities and liquid crystal molecular interaction. In relation to the control technology of optical reflection characteristics, effects of liquid crystal molecular structures (derivative effect and copolymer composition) on orientation were elucidated. As to the technology to form multi-dimensional anisotropic structures, efforts were made for the heightening of formation technology of simple RGB (red, green, blue) directional reflection layers using acrylate materials. The paper also outlined the comprehensive survey. (NEDO)

  7. FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the consortium based analysis technology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei kaiseki gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made to look for the consortium based analysis technology by which the consortium base can be analyzed as it is using the molecular biological method. Studies were made in the following four fields: 1) new identification technology of eucaryote using II DNA topoisomerase genes (PCR amplification method of II DNA topoisomerase genes); 2) method to detect new recognition peptide activated microorganism (adjustment of cortical antigen); 3) technology to elucidate detection/response mechanism of the specific environment and adaptation/resistance mechanism of the specific environment; 4) incubation method inside 3D matrices. In 3), studies were made of the analysis of inhibition mechanism of korormicin and separation of solvent-resistant oil degradable bacteria. In 4), for the settlement and dynamic analysis of microorganism consortium by studying incubation conditions, conducted was the molecular system analysis of bacteria and eumycetes inhabiting in sponge. (NEDO)

  8. FY 1998 report on the verification survey of geothermal survey technology, etc./Development of the reservoir fluctuation survey method (Summary). Theme 1. Development of the fracture hydraulic survey method; 1998 nendo chinetsu tansa gijutsu nado kensho chosa choryuso hendo tansaho kaihatsu hokokusho (Yoyaku). 1. Danretsu suiri tansaho kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The paper reported the results of the development of the fracture hydraulic method. As to the geothermal well hydraulic test method, the following were studied. Relating to the pressure transient test method, the detailed design of a system was conducted on a prototype hydraulic test system through the manufacture of element parts and feed back control mechanism and experiments to evaluate performance/operation characteristics of fields. Concerning the tiltmeter use measurement method, the field experiment by tiltmeter measurement was carried out in the Hijiori area where existing data and the wells used exist. With respect to the two-phase flow rate measuring method, by a combination of the existing vortex flow meter, vapor quality meter and tracer method, conducted were a field experiment on comparison/calibration of the existing flow meter and tracer method and a numerical simulation of change in vapor liquid in association with temperature/pressure changes in two-phase flow pipe, and the semi-quantitative calibration method was studied. About the water permeable logging method, study was made on the following items. In regard to the hydrophone VSP method, data analysis of the method was conducted. As to the development of individual feed zone flow meter measuring device, the evaluation was conducted of accuracy of Doppler shift rates for flow rate, pressure, flow velocity, well diameter and change in concentration and characteristics of acoustic unit. As a result, the flow rate was unable to be detected with satisfactory accuracy. (NEDO)

  9. Survey report for fiscal 1999 on advanced exploitation of coal overseas. Survey of coal exploitation enhancement overseas (Coal industry's measures for persistent low coal price); 1999 nendo kaigaitan kaihatsu kodoka nado chosa. Kaigaitan kaihatsu sokushin chosa (sekitan kakaku teimeika ni okeru sekitan sangyo no taiosaku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Surveys were conducted of the trends of coal companies in the U.S. and Australia and of the lookout for new coal field development in Australia for the purpose of contributing to the stable supply of coal in the future. In the U.S., the coal industry has experienced serious changes in these ten years, and various corporations, such as Peabody, Arch Coal, CONSOL, and Kennecott have come to resort to drastic measures for their survival. In Australia, coal price is lower and contract terms are shorter with less demand for coal supply thanks to the economic crisis in Asia. As for demand for coal in Asia, on the other hand, it is deemed that in 2010 there will be a 41% increase over the 1995 level and that, therefore, coal field preservation and new field exploitation are necessary. Since production by strip mining in New South Wales State is to decrease in 2012 and after, it is expected that new projects will start only after 2012. Comprehensive development projects are going to be launched in the areas surrounding the Surat district, Queensland State, and therefore new projects will be easier to start in this region. Since the Surat coal is to be collected after a little stripping, it is expected that it will be able to compete with the Indonesian coal. (NEDO)

  10. Achievement report for fiscal 1997 on the development of technologies for utilizing biological resources such as complex biosystems. Development of technologies for producing substitute fuel for petroleum by utilizing organisms; 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Technologies of producing useful substances using the substance decomposing/producing functions of complex biosystems and methods of their handling are developed. In the utilization of microbes in the digestive tracts of termites and longicorns, it is made clear that several kinds of termites cleave the {beta}-O-4 ether linkage. In relation to technologies for wood decomposing complex microbial system construction and complex vector system development, a screening system is constructed in which strains that exhibit complex actions are combined. Concerning the advanced utilization of tropical oil plants, conditions are determined for inducing callus out of oil palm tissues. Out of oil palm sarcocarp tissues, mRNA (messenger ribonucleic acid) is isolated for the construction of a cDNA (complementary deoxyribonucleic acid) library. For the purpose of isolating a powerful promoter, a partial base sequence is determined for ubiquitin that frequently expresses itself in cells. A pathogenic bacterium ailing the oil palm is sampled for identification, and it is inferred that the bacterium is a kind of Ganoderma boninense. (NEDO)

  11. FY 2000 report on the results of the technology development of energy use reduction of machine tools. Development of dry cutting use abrasion resistant/lubricous coated tools; 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Dry sessakuyo taimamo junkatsusei hifuku kogu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of energy conservation and reduction of environmental loads of machine tools, study was conducted on the dry cutting which is the cutting with no use of cutting oil, and the FY 2000 results were summed up. The study was made on dry cutting use abrasion resistance/lubricous coated tools coated with the composite membrane of which the cutting life become little lower than that of existing tools using coolant. In the survey of abrasion resistant/lubricous films, it was found out that in the adhesion to ultra-hard substrates, the DLC single-layer film consisting only of carbon indicated the same excellent adhesion as intermediate-layer inserts. As to the synthesis of abrasion resistant/lubricous films, the synthesis of the composite membrane (WC/C membrane) consisting of tungsten carbide (WC) and carbon (C) was made using arc ion plating device. The WC/C membrane is composed of W and C and has the structure in which at nm levels the layer with much W and the layer with less W were alternately piled. Study was made of devices necessary for the development of abrasion resistant/lubricous films and the film formation for drill. (NEDO)

  12. Fiscal 1997 report on the verification survey of geothermal exploration technology. 2. Development of the reservoir variation survey method (development of the gravity survey method); 1997 nendo chinetsu tansa gijutsu nado kensho chosa. Choryuso hendo tansaho kaihatsu (juryoku tansaho kaihatsu) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Among technology developments such as the reservoir evaluation at initial developmental stage and stabilization/maintenance of power after the start of operation, the fiscal 1997 result was described of the development of the gravity survey method. The paper conducted the installation of gravity measuring points outside the existing monitoring range, introduction of CG-3M gravimeter/GPS measuring system, drilling of ground water level monitoring well, etc. for the setup of a system for new gravity monitoring. Moreover, regular measurement of gravity was made for the first fiscal year, and at the same time the continued observation of ground water level, precipitation, atmospheric pressure, and temperature was started. It is necessary to study the effects on gravity variation such as gravity gradient and tidal correction. Conducted were collection/arrangement of the existing data and database construction for history matching/variation prediction in the Yanaizu Nishiyama area. The paper made surveys of the trends/literature. In the future, needed are the computation using density models of geothermal reservoirs and test use of EDCON`s downhole gravimeter. 44 refs., 30 figs., 17 tabs.

  13. Fiscal 1999 research and verification of geothermal energy exploring technologies and the like. Development of reservoir mass and heat flow characterization (Development of gravity monitoring technology - Summary); 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho (yoyaku). Choryuso hendo tansaho kaihatsu (Juryoku tansaho kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For developing a natural state simulation system to enable the seizure of reservoir characteristics from gravity changes, a gravity measuring network system is about to be constructed in the Nishiyama district, Yanaizu-machi, Kawanuma-gun, Fukushima Prefecture, where a geothermal power station is situated. The work centers about (1) the construction of a gravity measuring network system, (2) the development of a borehole gravimeter utilization technology, and (3) the development of analysis/evaluation technologies. Under item (1), 138 gravity measuring stations and 10 groundwater measuring stations are completed, and continuous and periodic measurements of gravity and groundwater levels are carried out. Furthermore, gravimeters are calibrated, and the elevation, latitude, and longitude are precisely determined for each of the measuring stations. Under item (2), model calculations are conducted for the Nishiyama district boreholes, as a step preparatory to borehole gravity measuring, by investigating the records of actual operation of equipment and by operating a reservoir simulation system. Under item (3), measures to deal with factors that impede precise measurement and conditions to meet for the analysis of gravity changes are studied, and efforts are started to construct the said natural state simulation system. (NEDO)

  14. FY 1997 report on the results of the industrial technology R and D project. Development of technology to use biological resources such as the complex biological system (Development of biological use petroleum substitution fuel production technology); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Experimental researches were conducted and the FY 1997 results were reported with the aim of establishing analytical technology for the complex biological system by which the complex biological system can be analyzed in such a state as it is using the molecular biological method. In the study of the molecular genetic analytical technology, PCR primers used for amplification of topoisomerase II genes of the whole eukaryote was designed. As to the histochemical analytical technology, a study was made on the new constitution microorganism detection method by the hybridization method and the antibody specific dyeing method, and the following were conducted: manifestation in quantity of colibacillus and the recovery, refining, and construction of peptide library by fuzzy display method. Concerning the functional analytical technology, technological researches were made such as the environmental adaptation mechanism of high thermophile and the information transfer mechanism among bacteria through cell membranes for elucidation of the special environment detection/response mechanism and the special environment adaptation/resistance mechanism. As to the separation/culture technology, various anaerobic microorganisms were separated from marine sponge for the development of a method of culturing in 3D matrices. (NEDO)

  15. Fiscal 1999 industrial science and technology R and D (industrial-academic) project report. R and D on technologies for creating bioaffinity molecules using submicron beads (Development of practical technologies for energy saving); 1999 nendo biryushi riyogata seimeitai ketsugo busshitsu nado sosei gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 R and D result on technologies for creating bioaffinity molecules using submicron beads. By improving particle production, favorable SGNEGDE particles for drug fixation were produced on a scale 10 times as large as previous one. Various functional groups were obtained for particles immobilizing ligands. Magnetic purification was attempted by using new magnetic polymer particles. Synthesis of particle unsusceptible to non- specific bonds, and analysis of its modified surface properties were attempted. Reversible attachable-detachable surface coat was obtained by immobilizing boric acid to glycol group on affinity latex SG particles. The experiment result on affinity latex for detecting one-point mismatched DNAs showed the dependence of DNA hybridization on shearing resistance. To construct the library of new substances reacting with bio-receptors, solid phase synthesis of anti- tumor heterocyclic compounds was analyzed. The library of the pharmacology of new lead compound such as sugar moiety was also constructed. Study was made on attachment of alkaloid to a solid phase, synthetic reaction on a solid phase and library construction. (NEDO)

  16. FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the petroleum substituting fuel production technology using biology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made. As a part of the study, the establishment was aimed at of the high-grade utilization technology of seaweed/algae using the degradation/conversion functions of the consortium base and the useful substance production technology by interaction of the consortium base of organism and flora/fauna. Studies for the establishment of the technology were made in the following two fields: technology to use unused resources such as lignocellulose and technology to produce petroleum substituting useful resources. As to the technology to use unused resources, the establishment was proceeded with of the technology to degrade/convert the seaweed-origin acidic polysaccharide into the useful substance using the consortium system. In FY 1998, in search of the excellent microorganism consortia which can degrade/solubilize carageenan, samples were picked up from the underwater of the Republic of Palau and incubated in the flat culture medium. Thirty-eight kinds of the degraded bacterium group were acquired. Using the degraded bacterium group, {kappa}-carrageenan was degraded and analyzed of the products. (NEDO)

  17. Report on research achievement in relation with developing fundamental combustion control technologies in fiscal 1998. Research and development of high-performance industrial furnaces; 1998 nendo nensho seigyo kiban gijutsu no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Development is intended to be made on fundamental combustion control technologies applicable to high-performance industrial furnaces that can reduce energy consumption and respond to environment preservation requirements. With an intention to achieve reduction in combustion exhaust gases such as carbon dioxide and nitrogen oxides, fundamental studies will be made on factors to decide flame shapes as represented by high-temperature combustion and flame shape control by utilizing microgravity environment, and researches will be made on combustion systems. Devices required for the experiments were fabricated to evaluate critical combustion characteristics of flames in furnaces including industrial furnaces, analyze and evaluate flame control parameters, and study low-pollution combustion technologies. Experimental methods acquired by 1997 were used for the experiments under the microgravity environment. Evaluation experiments were performed on flame shape control technologies and flame radiation characteristics, and basic experiments on the low-pollution combustion technologies. With these experiments, elucidation of the combustion mechanisms was launched by analyzing and evaluating the acquired data. A flame experimenting device for high-temperature preheated air completed by fiscal 1997 was used to acquire such combustion characteristics data as NOx discharge characteristics when the high-temperature preheated air is used. Based on the result thereof, verification was carried out on simulation models. (NEDO)

  18. FY 1998 annual summary report on manipulation of atomic and molecular extremes. Development of technologies for high-efficiency analysis/manipulation of DNA and the like; 1998 nendo genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho. DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The objectives are set to establish the techniques for observation/manipulation of atoms and molecules, as the common basic techniques for various industrial areas, e.g., new materials, electronics, biotechnology and chemical. Development of atomic field and scanning tunneling microscopes working under extreme conditions has been pursued, in order to manipulate complex systems, such as living body. For identification of molecular species, laser-excited fluorescence is combined with scanning mechanical probing to further refine the single molecule detection/identification techniques, and the objectives are set to develop a new method for evaluating molecules in a living body using a scanning probe microscope, and also to develop a novel scanning probe microscope for molecules in a living body. The other efforts were directed to R and D of the techniques for observing structures of organic molecules and the like through the measurements of adsorption process of organic molecules and clusters on semiconductor substrates and their surface reactions, and precision measurements of vibrational conditions of adsorbed molecular species reacting in the solid-liquid interfaces by high-sensitivity Raman spectroscopy to elucidate the catalysis mechanisms at the molecular level. (NEDO)

  19. Report on the achievements in fiscal 1998. Hydrogen utilizing international clean energy system technology (WE-NET). Subtask 8. Development of hydrogen combustion turbine (development of major components such as turbine blades and rotors); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 8. Suiso nensho turbine no kaihatsu (turbine yoku, rotor nado shuyo kosei kiki no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The present research and development is intended to establish the fundamental technologies required to develop a pilot plant, by investigating development of such major component devices as turbine blades and rotors in a hydrogen combustion turbine. In the turbine moving and stator blade cooling technology, it is intended to achieve the power plant efficiency of 60% (based on HHV) as established in the interim evaluation performed in fiscal 1996. Therefore, the necessary element tests, detailed blade design, and partial fabrication were moved forward on the three kinds of the selected blade cooling systems as the cooling systems that can deal with the steam temperature condition as high as 1,700 degrees C. Fiscal 1998 will execute the design and fabrication of test blades and testing devices for blade cooling evaluation tests to be performed at Tashiro Township in Akita Prefecture. At the same time, evaluation and selection will be made on the three kinds of the cooling blades. In the rotor cooling technology, for the purpose of analyzing the rolling-in phenomenon of steam in the main turbine flow, a method will be developed to analyze rotor disk cavity temperatures based on CFD, the basic sealing conditions based thereon will be discussed, and generalization will be made on the rotor cooling technology. (NEDO)

  20. Fiscal 1999 research and verification of geothermal energy exploring technologies and the like. Development of reservoir mass and heat flow characterization (Development of seismic monitoring technology - Summary); 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho (yoyaku). Choryuso hendo tansaho kaihatsu (jishinha tansaho kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Development is under way of a reservoir mass and heat flow characterization method using seismic wave analysis. Specifics of the endeavor cover detailed studies of techniques for monitoring and analyzing seismic wave changes due to changes in the reservoir that accompanies production and reinjection of geothermal fluids, which are carried out through preliminary monitoring accomplished at the test field. For the construction of a microearthquake monitoring network, a monitoring network design is prepared, a data processing/analyzing system is improved and tested for serviceability, analysis programs for 3-dimensional velocity structure analysis technology are improved, and methods for analyzing changes in the reservoir are deliberated, all these based on the results of microearthquake preliminary monitoring and simulation carried out at the Akinomiya district, Akita Prefecture. For the research of elastic wave velocity structure change, short-duration reflection events and waveform changes due to geothermal power plant periodic inspections are extracted, and studies are conducted about the applicability of the diffraction stacking method to the exploration of geothermal energy. (NEDO)

  1. Fiscal 1997 report on the results of the research on the development of high-performance industrial furnaces. R and D of high-performance industrial furnaces, etc; 1997 nendo seika hokokusho (koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho). Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A R and D was conducted for the purpose of developing remarkable energy conservation/CO2 reduction technologies. In fiscal 1997, the five working groups about the following were formed to have animated discussions: the basic research, heating furnace, heat treatment furnace, melting furnace, and tubular heating furnace. The research subjects are the pursuit/deepening of the base study on flame structures in high temperature air combustion, critical heat recovery of the system in high temperature air combustion, examination of the basic common technology on the ultimate optimization of the material heat transfer, construction of general-purpose experimental database, setting-up of design standards for general-purpose high-performance industrial furnaces, presentation of examples of the actual trial design based on the design standards and feasibility study of the practical application, preparatory support of the field test project on high-performance industrial furnaces for commercialization/diffusion/spread, etc. Further, how to arrange the developmental results was studied to make the results of the project useful for study of the prompt commercialization. 442 refs., 1444 figs., 311 tabs.

  2. FY 1998 report on the verification survey of geothermal survey technology, etc./Development of the reservoir fluctuation survey method (Summary). Theme 2. Development of the gravity survey method; 1998 nendo chinetsu tansa gijutsu nado kensho chosa choryuso hendo tansaho kaihatsu hokokusho (yoyaku). 2. Juryoku tansaho kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As to the construction of a network system for gravity measurement, the continued observation of groundwater level was carried out as a 24-hour observation by setting water-level gauges at 10 wells. At one of the wells (No. 5), the 24-hour continued measurement was conducted for gravity as well as groundwater level. At the 9 wells except No. 5 well, the traveling measurement of gravity was made. In relation to the gravity measurement, the periodic measurement of three times a year was conducted at 138 measuring points. And at the same time, the elevation at measuring point was asked by a combination of GPS measuring and level measuring. Concerning the borehole gravity meter, the existing gravity calculation program was revised, and the model calculation of borehole gravity values was made. In the analysis/evaluation, as to the gravity fluctuation analysis, relations were studied between the groundwater level fluctuation and gravity fluctuation. Also conducted were study of effects of the unsaturated zone density fluctuation on gravity and selection of a measuring method of the soil water content saturation degree. In regard to the study of the precise gravity measuring method, the vertical gravity gradient was measured, and the correction method was studied. Further, the development was made of tidal models which are adaptable to the Yanaizu-Nishiyama area. (NEDO)

  3. FY 1998 annual report on the compilation of database of experts for development of welfare equipment. Surveys for collecting information of institutes supporting, e.g., welfare equipment research and development; 1998 nendo fukushi yogu no kaihatsu ni kakawaru senmonteki chiken wo yushita jinzai database no kochiku chosa hokokusho. Fukushi yogu kenkyu kaihatsu nado shien kikan joho seibi chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to promote supply of high-quality, inexpensive welfare equipment, the data about public testing and research institutes throughout Japan are collected for their organizations, research themes, expertized areas, relations with welfare equipment, future activity guidelines and the like, and expert employees, so that enterprises can have adequate advises from them, when they plan to start researches on and development of related equipment. Information was obtained by means of questionnaires returned back from a total of 127 institutes related to industrial testing and researches, and 61 institutes, e.g., rehabilitation centers, deeply related to welfare equipment. This reports compiles information on 48 institutes which are conducting researches or the like on welfare equipment. The compiled lists of the local institutes supporting welfare equipment research and development activities describe, e.g., their total expenses, numbers of technical experts, conditions of windows responsible for welfare equipment or the like, percentages of expenses related to welfare equipment on total expenses, percentages of numbers of technical experts responsible for welfare equipment on total numbers of technical experts, and major research themes on welfare equipment. (NEDO)

  4. Technological development of machine tools using less energy in fiscal 2000. Achievement report on research and development of cutting process replacing electric discharge processing; 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Hoden kako wo chikansuru sessaku kakoho no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development has been made with an objective to replace the electric discharge processing consuming a large amount of energy and having environmental load, with the cutting process consuming less energy while maintaining the equivalent processing precision. This paper summarizes the achievements in fiscal 2000. Development of cutting tools has made three times or more as many multi-aspect utilization as compared to conventional tools possible by researching the tip shapes. In addition, ultra hard end mill suitable for cutting very hard materials using an ultrasonic cutting head was fabricated on the trial basis, and its cutting capability was verified. In developing the cutting processing heard, a vibration mode possible of cutting with the ultra hard tool was generated, ATC has become possible, and the possibility of cutting hard-to-cut materials was verified. For processing a narrow and deep part, an improved type tool was developed, whereas the practical cutting performance suppressing wear of the blade tip was obtained. To deal with the environment, development and prototype fabrication were performed on a unit having a grease lubricated high-speed main shaft that is considered to be the mainstream in the future. In the operation test at 20,000 min-L, know-how was acquired in relation with the basic performance, manufacture and use of the unit. (NEDO)

  5. FY 2000 report on the results of the technology development of energy use reduced machine tools, etc. R and D of the environment-friendly grinding machine system; 2000 nendo energy shiyo gorika kosaku kiki nado gijutsu kaihatsu seika hokokusho. Kankyo taiogata kensaku kako system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D were conducted of a grinding machine system of an environmental-friendly type in which no coolant is used or the amount of coolant is reduced, and the FY 2000 results were summed up. As to the ECOLOG grinding newly thought up, the roles were divided: the lubrication into a trace of the vegetable oil supplied onto the grindstone surface, cooling into a trace of the cooling water supplied to the structure, discharge of chips to the cooling water for bed table cleaning. By this, the amount of the cooling water becomes approximately 1/3 of that in the conventional grinding. Concerning the ECOLOG grinding using the usual grindstone, the grinding performance equal to that in the conventional grinding was confirmed. In the study for making the cooling water non-pollutant, the chlorine/sulfur free coolant was developed which includes no chemical substances designated by the PRTR law at all. It was confirmed that the grinding performance was almost the same level as the existing coolant which includes sulfur. In the study of the supply of coolant applied with ultrasonic waves, the result was obtained that in the optical glass grinding, the number of scratches decreased and the surface roughness improved even at the flow rate of coolant which is less than in the conventional grinding. (NEDO)

  6. FY 1998 report on the results of the development of utilization technology of biological resources such as bioconsortia. Development of the bioconsortia system utilization/production technology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of establishing the technology to use high grade functions of the bioconsortia system, the R and D were conducted, and the FY 1998 results were summed up. As to the study of functional material producing technology, screening of the 2400 strains owned by Marine Biotechnology Institute was conducted using reporter strain, and about 400 strains of homoserine lactone producing bacteria which are interbiological information convey substances were obtained. Concerning the effective decomposing/purifying technology of petroleum products, study of petroleum decomposition analysis technology was finished in the development of culture/control technology of petroleum decomposition microbial consortia constitutive bacteria. Relating to the analysis of the petroleum decomposition microbial consortia, changes in the bacteria population at the site of the heavy oil pollution accident on the Sea of Japan were investigated for the past one year by the PCR/DGGE method. It was found out that levels of the oil pollution in ocean could be assessed by measuring the concentration of Alcanivorax. As to the technology for highly utilizing unused petroleum fractions, conducted were the chemical analysis of photolytic crude oil, selection of the decomposition microbial consortia, etc. (NEDO)

  7. Fiscal 1996 report on the results of the R and D under a consignment from NEDO of environmental technology such as recycling (for public). 1; 1996 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Recycle nado kankyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo). 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This R and D is aimed at promoting reduction in environmental loads by waste, etc. and reutilization of waste, etc., and at developing environmental technology such as recycling contributing to reducing road traffic noise. Studies were made on operation conditions of material separation in the bottle state and flake state, color separation, washing process, etc. Moreover, tests were conducted on comparisons of performance of shredders with different functions. Running tests of 100,000 times were conducted to confirm effectiveness of durability of the paved road with used papers. Measurement of hardness of the resin using the sol-gel method and coating experiment using organic dye were carried out to study the membrane effect speed and flaw resistance of coating of coloring bottles. Gasification of shredder dust and separation of nonferrous metal and glass were conducted to get the basic data. As to FRP bath tubs, the ratio of glass fiber and plastics was studied and western tiles were trially manufactured. Further studies were made of removal conditions of noncombustibles, chlorine and sulfur content, and reaction conditions of alkali additives including kind, quantity and addition method. 166 figs., 132 tabs.

  8. Fiscal 1999 project for research and development of industrial and scientific technologies. Report on the achievements on the 'research and development of an ultimate atom and molecule manipulation technology' (Development of a technology to analyze and manipulate DNAs at high efficiency); 1999 nendo genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho. DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In the 'research and development of an ultimate atom and molecule manipulation technology', research has been made on an organic atom and molecule identification and manipulation technology and a dynamic organic molecule simulation technology. This paper summarizes the achievements in fiscal 1999. In the magnetic force controlling AFM for the force spectroscopy aimed at non-destructive atom and molecule identification, a prototype cantilever was fabricated that can excite and detect displacement in lateral direction and is suitable for friction measurement. The SrO surface and TiO2 surface of SrTiO{sub 3}. A carbon nano-tube was employed as a probe. In addition, the molecule inserting SAM technology was used to have developed a technology to measure electric conductivity inside and between molecules. With an aim at realizing a high-speed DNA base arrangement analyzing method, research is being performed upon noticing the single molecule method based on the light measuring method using the single molecule imaging as the base and the scanning probe microscope method. For the dynamic organic molecule simulation technology, theoretical analysis was advanced on synthesis of methanol on copper surface. (NEDO)

  9. Fiscal 1996 global environmental industry technology research related project. Report on the results of the consignment project of research and development of technology for reducing carbon dioxide emissions; 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu kanren jigyo. Nisanka tanso nado haishutsu teigen gijutsu kenkyu kaihatsu itaku gyomu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of reducing emissions of carbon dioxide, freon, etc., a research project was carried out of `Research and development of technology for reducing carbon dioxide emissions` which consists of 8 projects. The paper reported the results of the projects. The projects are: (1) Development of waste water treatment of submerged combustion system, (2) Development of thermoelectric generating devices, (3) Development of high performance heat insulation materials, (4) Development of methanol reformer for transportable fuel cell, (5) Development of large pressure reducing valves, (6) Development of large-scale turbo heat pump for district heating and cooling plants, (7) Development of heat pumps for transportation equipment, and (8) Development of thermoelectric cooling devices. In (1), the waste water treatment test was conducted and reached the target. In (2), the thermoelectric device using powder sintering element obtained performance twice the performance level of the existing device. In (3), (4), (5) and (6), the target was all reached. In (7), the results well agreed in a comparison between structural analysis and experiment. The cooling unit by the SPS sintering method using Bi-Te system sintered material element obtained the cooling efficiency almost the same as that by the freon compressor method. 8 refs., 161 figs., 63 tabs.

  10. FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the petroleum substituting fuel production technology using biology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made. As a part of the study, the establishment was aimed at of the high-grade utilization technology of seaweed/algae using the degradation/conversion functions of the consortium base and the useful substance production technology by interaction of the consortium base of organism and flora/fauna. Studies for the establishment of the technology were made in the following two fields: technology to use unused resources such as lignocellulose and technology to produce petroleum substituting useful resources. As to the technology to use unused resources, the establishment was proceeded with of the technology to degrade/convert the seaweed-origin acidic polysaccharide into the useful substance using the consortium system. In FY 1998, in search of the excellent microorganism consortia which can degrade/solubilize carageenan, samples were picked up from the underwater of the Republic of Palau and incubated in the flat culture medium. Thirty-eight kinds of the degraded bacterium group were acquired. Using the degraded bacterium group, {kappa}-carrageenan was degraded and analyzed of the products. (NEDO)

  11. Análise dos parâmetros cinemáticos determinantes do desempenho na prova de 200 m nado livre Analysis of the determinant kinematical parameters for performance in the 200-m freestyle swimming event

    Directory of Open Access Journals (Sweden)

    Maria Inês Ferreira

    2012-06-01

    Full Text Available Os objetivos deste estudo foram: i caracterizar o nado submáximo e máximo do ponto de vista cinemático; ii verificar a influência das variáveis cinemáticas na prova máxima de 200 metros crawl. Nove nadadores de elite nacionais realizaram dois testes: um submáximo, descontínuo de intensidade progressiva; outro máximo, que consistiu em uma simulação de uma prova de 200 m crawl. Foram estudados os parâmetros cinemáticos gerais da mecânica da braçada, a duração de cada fase do ciclo gestual, a velocidade do centro de massa e a variação intracíclica da velocidade horizontal. Verificaram-se diferenças cinemáticas significativas da frequência gestual, velocidade de deslocamento do centro de massa, duração total do ciclo gestual, duração da ação subaquática propulsora e da velocidade do centro de massa na fase de recuperação entre os testes. Identificou-se associações significativas entre o teste máximo e algumas variáveis cinemáticas como a velocidade do centro de massa e índice de nado.The main aims of this study were i to perform a kinematic characterization of sub and maximal swimming speed; ii to investigate the associations between the kinematic profiles and the 200 m front crawl style. Nine national level male swimmers performed two speed tests: a submaximal discontinuous speed trial of progressive speed intensity, and a maximal one, simulating a 200 m front crawl style. The stroke general kinematic parameters, the phases duration of the stroke cycle, the velocity of the centre of mass and the intra cyclic variation of the horizontal velocity were herein studied. Significant kinematic differences in relation to stroke rate, horizontal velocity of the centre of mass, total cycle duration, absolute and relative duration of the propulsive sub aquatic action and the velocity of the centre of mass during the arms recovery were compared between the speed tests. Significant correlations between the performance in

  12. Fiscal 1997 report on the results of the New Sunshine Project subsidiary operation. Development of the geothermal water use power plant, etc. (development of the binary cycle power plant / development of the geothermal well MWD system); 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (binary cycle hatsuden plant no kaihatsu (chinetsusei kussakuji kotei joho kenchi system no kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of improving efficiency and accuracy in geothermal well drilling, the development was conducted of an MWD (measuring while drilling) which detects borehole information in real time. In fiscal 1997, the following R and D were carried out. As to the downhole equipment, the actual well experiment on the sonde was conducted to confirm the basic performance. The design improvement, trial fabrication and experiment were conducted on mud pulse generating valve driving control equipment, bore hole signal processing unit and temperature correction circuit portion in the sonde. Concerning electronic parts, a heat resistance confirming test was conducted for data collection/assessment. Further, jigs were fabricated for tests to confirm working of each equipment. Relating to the ground equipment, conducted were improvement of the decoded program and betterment of the analytical system and interface. As to the development of the analytical system, data on depth were added to the azimuth/inclination obtained from MWD, which enabled indication of a well drilling tracing chart while drilling. 92 figs., 43 tabs.

  13. Fiscal 1995 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the binary cycle power plant (development of the measurement while drilling system for geothermal wells); 1995 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (binary cycle hatsuden plant no kaihatsu (chinetsusei kussakuji kotei joho kenchi system no kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The R and D were conducted of a detection system for measurement of data on the bottom hole of geothermal well, data transmission and signal processing, and an analysis system for well drilling trajectory control and well assessment while drilling of geothermal wells based on the data obtained by the detection system, and the results were reported of the technical development in fiscal 1995. In the development of the downhole detection unit, the following developments were conducted: mud pulse generator, bottomhole signal processor, mode switches, inclination information sensor, power source, measures against vibration/shock, sonde external equipment, tests to confirm heat resistance of electronic parts, and design/manufacture of testing devices. In the development of the surface detection unit, the development was made of experimental analysis program, interface program, and simulation. In the development of the analysis system, as a well trajectory control support system, made were a trajectory planning/display system and a trajectory prediction system. As a downhole assessment support system, made were a temperature analysis system and a pressure analysis system. 4 refs., 298 figs., 88 tabs.

  14. Achievement report in fiscal 2000 on technological development to recycle waste building materials and glasses. Development of waste building material recycling technology (Research and development of recycling technology corresponding to grades of demolished building lumbers); 2000 nendo kenchiku haizai glass nado recycle gijutsu kaihatsu seika hokokusho. Kenchiku haizai recycle gijutsu kaihatsu (kenchiku kaitai mokuzai no hin'i ni taioshita recycle gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to reduce wastes, and promote effective utilization of wood resources, research and development has been made on a demolished building material recycling technology. This paper summarizes the achievements in fiscal 2000. In developing the technology to manufacture high water resistant wood boards, discussions were given on resor type phenolic resin as an adhesive, and on the medium density fiberboard (MDF) being a substitute material for plywood as the wooden board. As a result, a highly water resistant MDF that can clear JIS E0 has been developed. In the research of a technology to enhance durability of wooden boards, the in-liquid roll press method was devised to perform impregnation of chemicals into board raw materials continually and simply, whose device was fabricated on a trial basis. With regard to recycling of medium to low grade wood-based wastes, researches were performed on pulverization of the wastes, fabrication of liquefied woods, and effective utilization of the liquefied woods. Both of a hammer mill and a chip saw crusher fabricated wood powder with nearly uniform grain size regardless of types of the wood-based wastes. Liquefaction of plywood and PB boards required more stringent reaction conditions than liquefaction of such ordinary members as pillar materials and laminated lumbers. (NEDO)

  15. Fiscal 1996 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the binary cycle power plant (development of the measurement while drilling system for geothermal wells); 1996 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (binary cycle hatsuden plant no kaihatsu (chinetsusei kussakuji kotei joho kenchi system no kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The R and D were carried out of a detecting system for measurement of data on the bottom of geothermal well, data transmission and signal processing, and an analysis system for well drilling trajectory control and well assessment while geothermal well drilling based on the data obtained by the detecting system. The paper reported the results of the technology development in fiscal 1996. In the development of the detecting system, improvement/design were conducted on a mud pulse generator constituting sonde, well bottom signal processing equipment, mode switch and inclined information sensor, and the system equivalent to the actual one was manufactured to conduct a running test at high temperature/pressure. Moreover, a test to confirm heat resistance of electronic parts was made for further improvement in heat resistance of the sonde, in order to obtain the data. In the development of an analysis system, conducted were enhancement of operability of the planning/indication portions of the well drilling trajectory supporting system, improvement of the data intake system, etc. In relation to the well assessment supporting system, carried out were heightening of operability of the temperature analysis portion and confirmation of accuracy increase. 5 refs., 253 figs., 72 tabs.

  16. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. First year report. Development of the production technology of clean hydrogen, etc. by direct methane reforming method; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Methane chokusetsu kaishitsuho ni yoru clean suiso nado no seizo gijutsu kaihatsu (dai 1 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The development was proceeded with of the hydrogen production method using the zeolite-base methane dehydrogenation cyclization catalyst with the specific porous structure. In this production method, there is no emission of process CO2, and hydrogen can be produced by supply of energy of 1/10 of that in the conventional technology. In FY 2000, the following were conducted: 1) conceptual design of a demonstrative experiment plant; 2) development of catalyst processing technology; 3) development of element technology such as improvement of catalyst performance. In 1), design/specifications for demonstrative experiment use plant were fixed by design estimation and process analysis using the mid-term fluidized bed experiment device. It was decided that the mid-term fluidized bed experiment device will be constructed to evaluate the methane reforming performance of catalyst and that the reaction tower should be the stationary fluidized bed type. In 2), a catalyst activity experimental device 100 times as large as the laboratory was fabricated to evaluate the catalyst performance. By optimization of reaction conditions and preparation of the catalyst composition, the targeted catalyst system was obtained. (NEDO)

  17. Antidepressant behavioral effects of duloxetine and amitriptyline in the rat forced swimming test Efeitos antidepressivos da duloxetina e da amitriptilina no teste do nado forçado em ratos

    Directory of Open Access Journals (Sweden)

    Honório Sampaio Menezes

    2008-10-01

    Full Text Available PURPOSE: To compare the effects of the antidepressant drugs duloxetine and amitriptyline on depressive behaviors in rats. METHODS: Fifteen male Wistar rats were given systemic injections of duloxetine, amitriptyline or saline prior to a Forced Swimming Test (FST. Immobility and number of stops were measured. Data were analyzed by one-way ANOVA and Kruskall-Wallis. RESULTS: Rats given injections of duloxetine displayed fewer stops than the amitriptyline and control group (pOBJETIVO: Comparar o efeito antidepressivo da droga cloridrato de duloxetina com a amitriptilina. MÉTODOS: O teste do nado forçado, teste comportamental que avalia a atividade antidepressiva em ratos, foi utilizado em 15 ratos Wistar, machos adultos, divididos em três grupos iguais: duloxetina, amitriptilina e controle. Os dados foram analisados pelo teste One-way ANOVA e Kruskall-Wallis. RESULTADOS: Houve diferença significativa entre o número de paradas (p <0,05 entre os grupos duloxetina e amitriptilina e o grupo controle. Grupo amitriptilina e controle não apresentaram diferença (p=0,8. CONCLUSÃO: A duloxetina reduziu o comportamento depressivo sendo mais efetiva do que a amitriptilina.

  18. Report on a survey in fiscal 1999. Supplementary survey on research and development of carbon dioxide fixation and effective utilization technologies utilizing bacteria and algae (the survey on feasibility of bio-technologies to create economic effects, such as the biological CO2 fixation technology); 1999 nendo saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu futai chosa. Keizaiteki koka wo soshutsusuru seibutsuteki CO{sub 2} koteigijutsu nado no biotechnology no kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Bio-technologies including the biological CO2 fixation technology, or the green bio-technologies (GBT) are the technologies indispensable in realizing the change to a resource circulating and environment harmonizing society that accompanies economical growth, or in other words, the 'sustainable development'. In quantifying the feasibility of these technologies, the GBTs that contribute to creating Japan's international competitive power and employment were specified, and an approach to establish the realization target in 2010 was adopted, upon identifying the general condition of the related markets inside and outside the country. The GBT is the technology that makes the best use of Japan's independent strength created by combining the enzyme engineering and fermentation engineering with the 'genome science' (HEART). The targets are to substitute four million kiloliters of petroleum with a resource circulation type energy generated by the bio-technology; apply the bio-technology to about 30% of products and processes produced or used in Japan's chemical industries; and aim at creating markets by using environmental measurement and analysis, treatment of hard-to-decompose substances, and supports on tree planting as the three pillars. A simulation on return on investment in GBT business suggests the effect of promoting PFI. (NEDO)

  19. Report on a survey in fiscal 1999. Supplementary survey on research and development of carbon dioxide fixation and effective utilization technologies utilizing bacteria and algae (the survey on feasibility of bio-technologies to create economic effects, such as the biological CO2 fixation technology); 1999 nendo saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu futai chosa. Keizaiteki koka wo soshutsusuru seibutsuteki CO{sub 2} koteigijutsu nado no biotechnology no kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Bio-technologies including the biological CO2 fixation technology, or the green bio-technologies (GBT) are the technologies indispensable in realizing the change to a resource circulating and environment harmonizing society that accompanies economical growth, or in other words, the 'sustainable development'. In quantifying the feasibility of these technologies, the GBTs that contribute to creating Japan's international competitive power and employment were specified, and an approach to establish the realization target in 2010 was adopted, upon identifying the general condition of the related markets inside and outside the country. The GBT is the technology that makes the best use of Japan's independent strength created by combining the enzyme engineering and fermentation engineering with the 'genome science' (HEART). The targets are to substitute four million kiloliters of petroleum with a resource circulation type energy generated by the bio-technology; apply the bio-technology to about 30% of products and processes produced or used in Japan's chemical industries; and aim at creating markets by using environmental measurement and analysis, treatment of hard-to-decompose substances, and supports on tree planting as the three pillars. A simulation on return on investment in GBT business suggests the effect of promoting PFI. (NEDO)

  20. Report on survey for possibility of applying bio-technologies to biomass in fiscal 1999. Aiming at developing a kitchen refuse and waste water treatment and energy production system that can be installed as an ancillary facility of buildings; 1999 nendo biomass eno bio technology oyo kanosei chosa hokokusho. Biru nado no futai setsubi to shite secchi kanona, chukai, haisui nado no shori narabi ni energy seisan system no kaihatsu wo mezashite

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the survey and discussion on a system to treat microorganisms generated from organic wastes and recover bio-gas energy as an ancillary facility of buildings. The roof of a building is the most suitable location in terms of open space and odor problem, and because the waste liquid after energy recovery can be flown into the city sewage system. Suitable processes for energy recovery are the primary fermentation, followed further by second stage fermentation purposed of reducing BOD. Since rapid enhancement of the efficiency cannot be expected from the present methane fermentation technologies, it is worth discussing to convert the first step from methane fermentation to hydrogen fermentation, for which technological development is indispensable. Permission by the national or local government would be an important condition. Organic wastes treatment systems with different scales may be considered from wastes treatment in each house to treatment of wastes after collection on the whole city basis. Treating wastes with high water content, such as kitchen refuses and human waste is beneficial among organic wastes being collected and treated by local governments. It is beneficial because sorted collection for that purpose can be carried out, and existing incineration systems can be operated more efficiently. (NEDO)

  1. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO (book on the handling / gas lift system). Report on the results of the R and D of the overall base technology of ocean resources (R and D of submarine oil drilling technology, etc.); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shine Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (kaitei sekiyu kussaku gijutsu nado kenkyu kaihatsu) seika hokokusho (handling / gas lift system hen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper conducted a R and D on the handling of drilling equipment in drilling/collecting of submarine oil and the gas lift of artificial oil extraction technology. As to each equipment of a barge style handling system, conducted were assembly/adjustment/trial run on land and pipe handling experiments on sea. In the experiment, confirmed were pipe transfer function, lifting function, fitting function, grasping function, etc. In the ocean experiment, studied were pipe bending stress, Karman vortex control effects, etc. Relating to the gas lift system, experiments were made on confirmation of fabrication/performance of air compressor. Moreover, a technique of air transportation to the blowing inlet of the gas lift pipe was established by developing an air blowing system and fabricating a long-distance flexible pipe. Concerning the gas/liquid/solid three-phase separator, a cyclone separator was developed, and improvement in lifting efficiency was confirmed. Helped by these, the problems of the gas lift system were almost solved, and a possibility of the commercial-base production system was obtained. 2 refs., 182 figs., 47 tabs.

  2. Neonatal treatment with fluoxetine reduces depressive behavior induced by forced swim in adult rats Tratamento neonatal com fluoxetina reduz o comportameto depressivo induzido pelo nado forçado em ratos adultos

    Directory of Open Access Journals (Sweden)

    Cristiano Mendes-da-Silva

    2002-12-01

    Full Text Available Serotonin plays a role at the pathophysiology of depression in humans and in experimental models. The present study investigated the depressive behavior and the weigh evolution in adult rats (60 days treated from the 1st to the 21st postnatal day with fluoxetine, a selective serotonin reuptake inhibitor (10 mg/kg, sc, daily. The depressive behavior was induced by the forced swim test (FST. The animals were submitted to two sessions of FST: 1st session for 15 min and the 2nd session 24h later, for 5 min. During the 2nd session the Latency of the Attempt of Escape (LAE and Behavioral Immobility (BI were appraised. The Fluoxetine group when compared to the Control group, showed an increase in LAE and a decrease in BI. The neonatal administration of fluoxetine reduced the depressive behavior in adult rats, possibly by increase in the brain serotonergic activity. This alteration can be associated to process of neuroadaptation.Estudos em humanos e em modelos experimentais demonstram que a serotonina (5-HT participa da fisiopatologia da depressão. O presente estudo investigou o comportamento depressivo e a evolução ponderal de ratos adultos jovens (60 dias tratados do 1º ao 21º dia pós-natal com fluoxetina, um inibidor seletivo de recaptação da serotonina, (10 mg/kg, sc, diariamente. A depressão experimental foi induzida através do teste de nado forçado (NF. Os animais foram submetidos a duas sessões de NF, a primeira por 15 min e a segunda após 24 h, por 5 min. Durante os 5 min de NF a latência da tentativa de fuga (LTF e o tempo de imobilidade (TI foram avaliados. O grupo tratado com fluoxetina apresentou aumento da LTF e redução do TI comparado ao controle. A administração neonatal de fluoxetina reduziu o comportamento depressivo em ratos adultos, possivelmente em função do aumento da atividade serotoninérgica cerebral. Esta alteração poderá estar relacionada a processos neuroadaptativos.

  3. FY 2000 report on the results of the development of the program system CO2 fixation/effective utilization technology. Development of the technology to assess global warming gas recovery/emission control by restoring/preserving the tropical mangrove coastal ecosystem; 2000 nendo program hoshiki nisanka tanso koteika yuko riyo gijutsu kaihatsu seika hokokusho. Mangrove nado nettai engan seitaikei no shufuku hozen ni yoru chikyu ondanka gas kaishu hoshutsu yokusei hyoka gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of developing the technology to assess the CO2 storage amount using the tropical mangrove coastal ecosystem, survey was conducted in the mangrove tree area in Ishigaki island, Japan and in Trat province, Thailand, and a draft of the assessment method was worked out. As to the assessment of the CO2 existence amount by analysis of satellite pictures, the regression equation between the mangrove existence amount and Landsat satellite data was determined to study a method for assessment of the CO2 storage amount in the whole area for survey. Further, using the relational equation between NDVI and LAI, vegetation indices reflecting vegetation conditions, methods to estimate the CO2 absorption amount by photosynthesis of mangrove tree community, the CO2 emission amount by respiration and the net production amount. Concerning the technology to assess the terrestrial area photosynthesis CO2 absorption amount, methods were studied for direct measurement of the amount of photosynthesis/respiration of the leaf area of mangrove tree community and the respiration amount by area such as trunk, branch and root and for assessment of CO2 absorption amount. Besides, studies were made on a variety of items such as the CO2 absorption/emission amount by underwater photosynthesis/respiration and decomposition of organic substances, the seawater exchange amount, and the rate of decomposition of organic substances. (NEDO)

  4. FY 1998 result report. Study of a total system for the development of superconductor power application technology (Feasibility study of commercialization of superconductivity technology and study of the introductory effect. Future superconductivity technology development in Japan); 1998 nendo seika hokokusho. Chodendo denryoku oyo gijutsu kaihatsu total system nado no kenkyu chodendo gijutsu no jitsuyoka kanosei oyobi donyu kokanado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    As a part of the New Sunshine Project, 'an R and D project on superconductor power application technology,' an examinational study was made as a mini project to clarify the developmental course for commercialization of superconductor technology. The superconductor technology is being watched with interest as a technology in the 21st century. In the application to the electric power/energy field, in particular, expected are the energy saving effect by high operation efficiency, excellent environmentality, developmental potentiality of new equipment/system by the application of ferromagnetism, etc. Accordingly, the paper analytically arranged the needs of superconductor devices in Japan and abroad and the technology seeds corresponding to the needs, and prepared the developmental subjects of superconductor technology. These developmental steps and the mutual relationship were expressed in an R and D framework. At the same time, as to the superconductivity, a survey outlined the projects carried out in each government office in Japan. The future developmental course was indicated, and proposals were made on the equipment/system as object which are the subjects for urgent development for commercialization. (NEDO)

  5. FY 1998 result report. Study of a total system for the development of superconductor power application technology (Feasibility study of commercialization of superconductivity technology and study of the introductory effect. Future superconductivity technology development in Japan); 1998 nendo seika hokokusho. Chodendo denryoku oyo gijutsu kaihatsu total system nado no kenkyu chodendo gijutsu no jitsuyoka kanosei oyobi donyu kokanado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    As a part of the New Sunshine Project, 'an R and D project on superconductor power application technology,' an examinational study was made as a mini project to clarify the developmental course for commercialization of superconductor technology. The superconductor technology is being watched with interest as a technology in the 21st century. In the application to the electric power/energy field, in particular, expected are the energy saving effect by high operation efficiency, excellent environmentality, developmental potentiality of new equipment/system by the application of ferromagnetism, etc. Accordingly, the paper analytically arranged the needs of superconductor devices in Japan and abroad and the technology seeds corresponding to the needs, and prepared the developmental subjects of superconductor technology. These developmental steps and the mutual relationship were expressed in an R and D framework. At the same time, as to the superconductivity, a survey outlined the projects carried out in each government office in Japan. The future developmental course was indicated, and proposals were made on the equipment/system as object which are the subjects for urgent development for commercialization. (NEDO)

  6. Achievement report for fiscal 2000 on development of technology related to new recycled products. Research and development of simultaneous recovery of chlorine contained in waste plastics and alkali contained in waste glass bottles; 2000 nendo shinki recycle seihin nado kanren gijutsu kaihatsu seika hokokusho. Hai plastic gan'yu enso to hai glass bin gan'yu alkali no doji kaishu ni kakawaru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Researches have been made on a technology to have alkali contained in waste glass bottles reacted with chlorine contained in waste plastics to separate and remove salt, and reuse the residues as a resource for cement raw material. This paper summarizes the achievements in fiscal 2000. In the research, glass powder pulverized to 5 to 10 {mu} m, calcium carbonate, iron oxide, and alumina were used to prepare raw material for the ordinary Portland cement. Vinyl chloride pulverized to 3 mm was added into this cement raw material so that chlorine-alkali equivalent ration will be 1.0, and the material was sintered in a rotary kiln at 800 to 1,400 degrees C. As a result, it was discovered that salt is produced from the alkali in glass and the chlorine in vinyl chloride, whereas the produced salt volatilizes when heated to 1,200 degrees C or higher, and clinker containing low chlorine and alkali can be produced. The test result reveals that the control range of the chlorine and alkali ratio is from 1.0 to 1.1. The remaining problems are measures against carbon monoxide and dioxin contained in the exhaust gas, and treatment of dust containing salt. (NEDO)

  7. Estudio preliminar de la expresión proteómica cerebral de la región hipocampal de ratas expuestas a diferentes niveles de estrés inducido por el nado forzado Preliminary study of cerebral proteomics expression of hippocampal region from rats exposed to different stress levels induced by forced swimming

    Directory of Open Access Journals (Sweden)

    Guerrero Nasser

    2012-04-01

    Full Text Available Introducción: en general, los estímulos estresores pueden inducir respuestas adaptativas o mal adaptativas dependiendo, entre otras cosas, de su intensidad y la duración. Sin embargo, no se han llevado a cabo estudios que relacionen cuantitativa y cualitativamente la intensidad de estrés al que es expuesto un animal y la expresión de proteínas del hipocampo. Objetivo: evaluar la expresión diferencial de proteínas hipocampales en ratas Wistar-UIS, expuestas a diferentes niveles de estrés inducido por el nado forzado. Materiales y métodos: se utilizaron 30 ratas Wistar-UIS machos distribuidas aleatoriamente en 3 grupos según el tiempo de exposición al nado forzado como estímulo estresor (0, 5 y 15 minutos. Después de 24 horas se extrajeron los hipocampos dorsales y se realizó electroforesis bidimensional de las proteínas extraídas. A continuación, se llevó a cabo el procesamiento de las imágenes de los geles obtenidos utilizando el software PDQUEST 2D. Aquellas proteínas en las se detectaron intensidades asociadas a los tiempos de exposición al estímulo, se identificaron de manera presuntiva utilizando la base de datos bioinformática Export Protein Analysis System (EXPASY. Resultados: de acuerdo con el análisis proteómico y bioinformático se identificaron 60 proteínas, de las cuales, 38 eran comunes al hipocampo derecho e izquierdo; 13 del hipocampo derecho y 9 del izquierdo. Conclusión: se encontraron diferencias en la expresión de proteínas entre el hipocampo derecho e izquierdo del tipo dosis dependientes decrecientes después de haber sometido a los animales a diferentes niveles de estrés inducido por la prueba de nado forzado. Salud UIS 2012; 44 (1: 17-27Introduction: in general stressful stimuli can induce adaptive maladaptive responses, depending among other things, of their intensity and duration. However, no studies were found in the literature that link quantitatively and qualitatively the intensity of

  8. Optimization of sustaining swimming speed of matrinxã Brycon amazonicus: performance and adaptive aspects Otimização da velocidade de nado sustentado em matrinxã Brycon amazonicus: rendimento e aspectos adaptativos

    Directory of Open Access Journals (Sweden)

    Gustavo Arbeláez-Rojas

    2010-01-01

    ,5 comprimentos corporais - BL por segundo. As melhores velocidades de nadado estiveram entre 1,0 e 1,5 BL s–1, nas quais o crescimento dos peixes foi 20% maior que nas outras. A hemoglobina e as células vermelhas do sangue em 1,5 BL s–1 aumentaram 24% e 18% respectivamente; o hematócrito foi 17 % maior em todos os peixes exercitados; o conteúdo de proteína do músculo branco em 1,0 BL s–1 foi 2% maior; a deposição de lipídio no músculo vermelho em 1,0 BL s–1 foi 22% maior e a retenção de água foi 3% menor. Os níveis de energia bruta aumentaram 10% em todos os peixes exercitados; a retenção de água no fígado foi 6 % menor em 1,0 BL s–1; a composição de lipídio no fígado foi 29% maior do que o controle e 34% maior do que a 1,5 BL s–1; a energia bruta no fígado aumentou em 1.0 BL s–1 comparada com o controle e 2,5 BL s–1. A deposição de lipídio no músculo ventral foi 9% maior em 2,0 BL s–1. Embora alta deposição de lipídio em matrinxã tenha sido obtida em velocidades moderadas de nado, os lipídios podem ser a fonte de combustível principal para manter as exigências metabólicas de matrinxã em exercício. A melhor velocidade de nado para obter o melhor crescimento em matrinxã está entre 1,0 e 1,5 BL s–1.

  9. FY 2000 report on the verification survey of geothermal exploration technology, etc. Development of the reservoir fluctuation exploration method - Phase 2 (Feasibility survey); 2000 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. Choryuso hendo tansaho kaihatsu phase 2 F/S chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of developing the technology to grasp the behavior of geothermal fluids flowing inside the deep-seated reservoir, study of subjects was made for the reservoir fluctuation exploration method - Phase 2. In the overview of the reservoir fluctuation exploration method - Phase 1, various element technologies being developed in Phase 1 were arranged in terms of the overview of technology, results concretely obtained, present subjects, achievement of technical development, etc. In the overview of geothermal fields, domestic geothermal fields and overseas geothermal fields were outlined of which demonstrative tests in Phase 2 can be made. In the survey, data on characteristics of reservoirs at the sites proposed, existing data usable for the project and information of the existing facilities were covered in terms of the those that can be collected being based on the public data. In the study of demonstrative testing fields, to make selection of demonstrative testing fields in Phase 2, selection of conditions was made from the two points of view: 'necessary conditions for demonstrative testing field' and 'comparison in adaptability of geothermal fields by method.' (NEDO)

  10. Achievement report for fiscal 1997 on joint research to develop fuel cell technologies for urban energy centers. Research on evaluating life of phosphoric acid fuel cells; 1997 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu kyodo kenkyu seika hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    This paper discusses life evaluation on phosphoric acid fuel cells of urban energy center type for regional energy supply and on-site type to be installed in buildings. Operation characteristics tests and disassembly checks allow to identify factors for voltage decrease, and estimate the life therefrom particularly if the voltage decrease is caused from catalyst activity. The time before 10% decrease value is reached is now about 40,000 hours. The creep analysis method that has been developed recently can predict deformation in full-size reformers nearly exactly, and is effective in operating the reformer and evaluating the life at the design stage. Creep buckling is the critical value, which is caused by ecliptic deformation of internal tubes in the second catalyst layer. In a heat exchanger for fuel gas preheating, carbon in the reformed gas is carbonized and deposited due to catalytic action of nickel in the brazing material that bonds plates and fins in the heat exchanger. Iron also has a possibility of performing catalytic action. In the on-site type 1,000-kW class fuel cells, no structural problems have been presented even after the operation has been stopped. In order to extend time interval between phosphoric acid supply into the cells, it is necessary to reduce difference in the remaining phosphoric acid amounts in the stack lamination direction and in the cell flat surface. (NEDO)

  11. Project in fiscal 2000 of developing international standards for supporting new industries. Standardization of communication interface for open robots in production system; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Seisan system nado ni okeru open robot yo tsushin interface no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to realize the open use between robot controllers and personal computers on the communication level, R and D has been performed on the standard API required for structuring the applications to use robot information on the personal computers. A draft of the international standard was prepared. This paper summarizes the achievements in fiscal 2000. The current fiscal year has executed improvements on the standard API software, as well as the demonstration tests. The following achievements were obtained: problems in practical use based on the demonstration tests of RAO ver. 0.5 were extracted and rectified; the standard API (Ver0.9) given additional functions including file transfer was developed; the specifications for the standard API (Ver1.0) were compiled based on the result of discussions on the major application functions; as a result of the demonstration test on reliability of the standard API (Ver0.9), performances were verified when the API is connected under different structural and using conditions; and a resolution was made at the ISO/TC184/SC2 international conference that 'continuation is encouraged on the present R and D expected as a proposal for the new work items'. (NEDO)

  12. FY 1999 project on the development of new industry support type international standards. Standardization of a method to evaluate the performance of open robot use communication interface in production system, etc.; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Seisan system nado ni okeru open robot yo tsushin interface no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of standardizing the communication interface system between personal computers and robots, the R and D were conducted on ORiN (Open Robot Interface for the Network), and the FY 1999 results were summed up. ORiN is composed of the provider part, kernel part and application logic part. The provider absorbs differences in expression and protocols of robot controller data of each company and conveys them to the kernel part. The kernel part is composed of RAO and RDF. RAO adopts the disperse object model DCOM technology and supplies the network transparency and common access method to robot. RDF supplies files with expansion of robot structure models using XML. By this, ORiN was made adoptable for future, permitting differences in each robot. In the International Robot Exhibition held in October 26-29, 1999, the prototype of ORiN was jointly demonstrated by each company. (NEDO)

  13. FY 1996 report on the results of the development of superconductor power application technology. Study of a total system, etc. (Investigational study of the introductory effect); 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Total system nado no kenkyu (donyu koka no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Under the secondary interim assessment made in FY 1995 between the assessment committee of the energy/environment technology development sectional meeting of the Industrial Technology Deliberation Council and NEDO, in this project, the following were conducted in FY 1996: study of trial manufacture of superconductor motor model machine and R and D of element technology (conductor technology/refrigerator technology). The study was proceeded mainly with Super-GM, and as to the motor, the preparation for test on a part of the model machines was finished. Considering FY 1998 which is the final year of this project, the investigational study in FY 1996 aims at accumulating/arranging/analyzing the data which help judge how to proceed with the future R and D of superconductor power application technology continuously based on the secondary interim assessment. For superconductor motor and various superconductor power appliance, economical/technical feasibilities and methods of R and D and surveys of trends in Japan and abroad for the R and D were made important items. Further, 'R and D of the basement of superconductor power application' proposed in the secondary interim assessment (R and D of the combination of elements which become the basement of equipment technology over a stage of parallel R and D of element technology of conductor, etc.) targeted the presentation of concrete details. (NEDO)

  14. Fiscal 1998 New Sunshine Project research report. Development of separation technology of hetero-compounds from coal-derived oil, and use methods of them; 1998 nendo sekitan ekikayuchu no tetero kagobutsu nado no bunri gijutsu to yoto no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project develops the efficient separation technology of compounds including hetero-atoms such as O and N from coal- derived oil, and researches effective use methods of them. Study is made on the concrete applications and problems of the following separation technologies of hetero-compounds: Distillation/refrigeration, extraction, supercritical gas extraction, pressurized crystallization, crystallization, adsorption, and membrane separation technologies. Based on the study result, the applicability of such various separation technologies of hetero-compounds from coal-derived oil fractions is confirmed experimentally. By using the newly developed bench-scale test equipment of an optimum separation process, the process performance is confirmed, and various engineering data are collected. Study is also made on the effective use method of the hetero-compounds separated by the above equipment. In fiscal 1998, as the electric membrane dialysis experiment result on phenolates derived from phenols in Kashima pilot naphtha and atmospheric light oil, the existence of substances (Ca, Fe, SO{sub 4}) deteriorating membranes was confirmed. Preventive measures against contamination of these bivalent cations and anions are one of future issues. (NEDO)

  15. FY 1998 report on the waste processing/recycling related technology, 'The R and D of lead-free solder standardization'; 1998 nendo haikibutsu shori recycle kanren gijutsu seika hokokusho. Namari free handa kikakuka nado kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To reduce the environmental pollution caused by lead eluted from the electronic equipment waste, the R and D on lead-free solder were conducted and the results were summarized. As to the basic characteristics, the evaluation test method was studied in terms of the range of melting temperature, mechanical strength, wettability and joint strength, to select a uniform test method. As the lead-free solder, Sn-Ag alloys were mainly used and mixed in a combination of Cu, Bi and In. Changes in characteristics were made clear by adding trace elements such as Ge, Mn and P. Relating to the applied characteristics, in selection of solder materials, materials were selected for which evaluation of the commercialization is proceeded with from a viewpoint of promotion of commercialization. Concerning the experimental evaluation of characteristics of lead-free solder in mounted substrates, it was indicated that basically lead-free solder can be practically used. Further, it was indicated that the Sn-Ag-Cu-Bi system depends not on solder composition but on active force, printing accuracy and flux characteristic of solder paste, that improvement of solder paste has an effect on mounting characteristics. (NEDO)

  16. General report on the results of the development of fuel cell technology such as urban energy center. Evaluation study of life of phosphoric acid fuel cells (fiscal 1995 and 1996); Toshi energy center nado nenryo denchi gijutsu kaihatsu kenkyu seika sogo hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu (1995 kara 1996 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Receiving subsidies from MITI, NEDO carried out this project in fiscal 1995 and 1996 as a joint research with Technology Research Association for Phosphoric Acid Fuel Cell Power Generation System and others. The project aimed at developing the accelerated test method which can evaluate in a short time the cell life of phosphoric acid fuel cells (PAFC) and the lowering of characteristics. The accelerated test method of PAFC life is thought to be a tool indispensable for the promotion of commercialization, but the accelerated test method like the usual material evaluation has not yet been established. To solve this problem, procedures were developed to rationally plan the accelerated test on short stacks of full scale based on the small cell test data. Here, to rationally estimate the operational state under actual conditions based on the data on the accelerated test, it is necessary to fully understand the mechanism of deterioration of PAFC. By conducting in parallel the element study for the basic elucidation of cell deterioration phenomena, obtained was the useful information/knowledge which back up the results of the accelerated test scientifically. 168 figs., 33 tabs.

  17. FY 1999 Industrial science and technology research and development project. Report on the results of research and development of the technologies for genome informatics (Acceleration of analysis of green mold transcription control information); 1999 nendo genome infomatics gijutsu kenkyu kaihatsu seika hokokusho. Koji kabi no tensha seigyo joho no kaiseki kasokuka nado

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A total of 49 budding yeast transcription factor disruptants and one conditional transcription over expression strain are produced, to elucidate the gene regulation networks using the gene expression profile data, and to measure the systematic and high-quality gene expression profiles using the Affymetrix's GeneChip system. The program is also developed for accurately predicting the base sequences which regulate expression of given gene groups, based on the uniqueness of the upstream sequences. The analysis with the aid of the program predicts 8 gene expression regulation sequences, which are considered to be novel, from the gene groups of retarded expression by the transcription factor disruptants. The time course gene expression data are produced from the transcription factor SW14 conditional over expression strain. The analysis of the data indicates that the analysis of the subtracted genes using the gene expression profiles from the wild type strain is useful for clarifying the effects of the derived transcription factor over expression. (NEDO)

  18. FY 1998 report on the verification survey of geothermal survey technology, etc./Development of the reservoir fluctuation survey method (Summary). Theme 5-1. Technology to predict reservoir fluctuations; 1998 nendo chinetsu tansa gijutsu nado kensho chosa choryuso hendo tanhsaho kaihatsu hokokusho (yoyaku ). 5-1. Choryuso hendo (choryuso hendo yooku gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The existing gravity post processor was improved and a feasibility study of downhole gravity profile measurement was conducted. As compared with the earth surface, great fluctuations could be observed in the downhole, indicating a possibility of acquiring the useful information on underground steam zones. The existing self-potential post processor was improved, which made the history matching analysis easy. A geochemical post processor was developed which can analyze geochemical fluctuations. Changes in resistivity in reservoir associated with production/injection of geothermal fluids were calculated, and a feasibility was shown of developing the resistivity post processor into which the existing MT forward calculation method was efficiently integrated. From the data on effects of changes in temperature/fluid phase on seismic wave velocity and damping, usability of the seismic wave post processor was made clear. From the reservoir fluctuation analysis using gravity/self-potential post processor, it was found out that gravity fluctuations at Onikobe had already finished and presently there are less fluctuations. Self-potential is still in fluctuations and becomes indices of reservoir fluctuations. Study was made also on Sumikawa where steam is dominant. (NEDO)

  19. Fiscal 1997 report on the verification survey of geothermal exploration technology. 5-1. Development of the reservoir variation survey method (technology of prediction of reservoir variation); 1997 nendo chinetsu tansa gijutsu nado kensho chosa. Choryuso hendo tansaho kaihatsu (choryuso hendo yosoku gijutsu) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the reservoir evaluation at an initial developmental stage and stabilization/maintenance of power after the start of operation, the fiscal 1997 result was described of the study of technology of prediction of reservoir variation. Using the conventional post processor, feasibilities were computed of reservoir models and behavior after the development, and gravity/self potential/resistivity variation. Variation in the seismic wave speed structure was large in travel time change distribution. The measuring accuracy of 1m sec is required to get enough detection resolving power. A conceptual design of the post processor development was conducted to study a system operated on Windows. Based on the reservoir numerical simulation technology, by taking in variation parameters such as gravity and self potentials as new model constraint conditions, the reservoir modeling technology which increased in accuracy by history matching was trially developed. Using the conventional reservoir model in the Oguni area, predictably computed were reservoir behaviors during 50 years which simulated a 20 MW development. Effectiveness of the post processor were able to be shown though influenced by characteristics such as permeability and resistivity. 74 refs., 95 refs., 12 tabs.

  20. FY 1998 result report. Report on the results of the examinational research on the trend of technology development in the iron/steel industry; 1998 nendo seika hokokusho. Tekko sangyo no gijutsu kaihatsu doko nado ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The trend of the technology development in the Japanese iron/steel industry was compared with those in foreign countries and surveyed to increase the international competitive strength. From the viewpoints of technology, industry and goods, the iron/steel field was characterized based on the statistic data, and especially automobile use steel materials were selected such as cold rolling high tension steel sheet, surface treated steel sheet, and bearing sheet. The analysis of factors of competitive superiority was conducted, and the following were presented: measures for process continuation, and measures taken from the age of equipment and cost indexes. The paper also surveyed the trend of pig iron making/steel making technology in Asia. The present international technical competitiveness in the iron/steel industry in Japan, especially of automobile use steel sheet, is very high. This is because of the well-functioned demand-oriented development, and also as a result of the mutually influentially conducted equipment development such as process continuation and development of new goods, supposing the iron/steel continuous process and reduction in impurities. However, fears are the stagnation in the recent technical development strength and the saturation of new equipment. Moreover, the further heightening is needed of the international cost competitive strength of general-purpose products. (NEDO)

  1. FY 2000 report on the R and D of the particulate utilization type creation technology of biological connective substances. Survey of the technical trend overseas; 2000 nendo biryushi riyogata seitai ketsugo busshitsu nado sosei gijutsu no kenkyu kaihatsu seika hokokusho. Kaigai gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper summarized the reports on the results of Japanese engineers' participating in the related scientific meetings held overseas as a survey report on the trend of the overseas technology. The scientific meetings they participated in were: 1) Impact of Genomics on Medicine and Pharmacogenomics Europe (Amsterdam; May 15-26, 2000), 2) Drug Discovery Technology 2000 (Boston; August 10-20, 2000), 3) Biotechnology 2000 (Berlin; September 3-12, 2000), 4) PacificChem 2000 (Hawaii; December 14-21, 2000), 5) 4th Winter Conference on Medicinal and Bioorganic Chemistry (Seattle; January 27 - February 4, 2001). Impact of Genomics on Medicine was composed of the following five fields: microarrays, proteomics, functional genomics and target validation, genetic variation technology, and applications of SNP analysis (joint session). Pharmacogenomics Europe was composed of the following four fields: applications of SNP analysis (joint session), SNP assays, targets and compounds, and clinical applications. (NEDO)

  2. Fiscal 1998 achievement report. Venture business raising type regional consortium - Small business creation base type (Development of nursery tray pickup robot and transport system for rice or vegetable growing); 1998 nendo suito oyobi yasai nado no hako ikubyo no robot naetori hanso system no kaihatsu (dai 2 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The project aims to develop energy conservation technologies through robotizing the processes of uprooting and conveying rice or vegetable seedlings. In fiscal 1998, the task covered root cutting and seedling uprooting, and a method was designed in which seedlings were uprooted through the intermediary of strings placed to run under the nursery trays. An effort was started to build an experimental root-cutting/seedling-pickup device. Systems for housing and conveying seedling trays were built simultaneously with a seedling tray loading system. In fiscal 1999, the root-cutting/seedling-pickup device was tested repeatedly for its seedling-pickup performance, and was modified. The nursery tray housing and conveying system accommodates a total of 84 trays in a 2-line 7-stage arrangement with 6 trays mounted on each stage. The conveyance speed was set at 0.4m/s-0.5m/s, and the trays travelled with stability in the system house. As for tray loading, an experimental device was built in which the mechanism for replacing empty trays with full trays had been changed from the turn table mechanism to a lateral movement type. Tests were conducted and it was demonstrated that the experimental device operated smoothly. A commercialization survey was conducted, and a conclusion was reached that a quarter of the target farmers in Hokkaido would positively accept the new technologies and adopt this system. (NEDO)

  3. Research and development of utilization technology of solar thermal energy system for industrial and other use. Research and development of solar system (investigation of popular type snow melting systems); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Solar system no chosa kenkyu (fukyugata yusetsu system no kenkyu chosa)

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for investigation for popular type snow melting systems using solar energy. Two types of technologies are proposed to utilize solar energy for snow melting in winter and create comfortable environments. One is combined (active plus passive) type, which transfers solar heat it collects by the whole wall surfaces to an attic to heat it totally, and makes the whole roof as a radiator to melt snow. However, heat radiated from the roof is insufficient to melt all snow on the roof, allowing it to remain to an extent that it works as an insulator. The other is active type, which transfers heat it collects by the collector to the heat storage tank, from which heat is extracted in winter for various purposes, including snow melting. Such a system must store heat for an extended period, for which a highly insulating heat storage tank is proposed to balance capacity of heat storage between seasons and building size.

  4. Research and development of utilization technology of solar thermal system for industrial and other use. Research and development of key technology (energy conversion on technology using chemical reactions); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Yoso gijutsu no kenkyu (kagaku energy henkan gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for energy conversion technology using chemical reactions by the aid of solar energy. The demonstration runs were conducted by a bench-scale unit, which was operated stably for 100h, to produce promising results. The catalyst exhibits stable performance, without showing a sign of deactivation. It is found that the heat pump system works well, without being interfered with accumulated by-products. A heat of approximately 2,100kcal/h is recovered. It is confirmed that steam of 150{degree}C and 200{degree}C is generated from hot water of 80{degree}C and 95{degree}C, respectively. The bench-scale runs show a thermal efficiency of around 10%, which is lower than the target level. However, the runs with hydrogen-occluding alloy attain a process thermal efficiency of 30%. The system in which solar collector and chemical heat pump units are combined is evaluated with respect to its economic efficiency and operability for its eventual commercialization. 6 figs., 2 tabs.

  5. Research and development of utilization technology of solar thermal system for industrial and other use. Research and development of solar system (research for solar/energy-conservation technology retrofitted to existing buildings); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Solar system no chosa kenkyu (solar toshi muke gijutsu ni kansuru chosa)

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for solar/energy-conversion technologies retrofitted to existing buildings. The estimated effects and economic viability of retrofitting technologies show that they bring very high energy-saving effects when applied to heating and hot water supply, which consume a large portion of energy, but relatively low energy-saving effects when applied to cooling, solar walls, glazed balconies and transparent insulators. The study on applicability of these technologies in Japan indicates that the technologies which can recover cost within an average life time are those applied to windows, solar collector systems for hot water supply and heating, and transparent insulators. Although these technologies are low in applicability to cooling viewed from the angle of cost recovery, retrofitted radiation type cooling systems improve not only cooling and energy-saving effects but also comfortableness.

  6. FY 2000 report on the results of the R and D of the technology for rationalization of energy utilization and for CO2 fixation using recycled paper; 2000 nendo energy shiyo gorika koshi nado yuko riyo nisanka tanso koteika gijutsu kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In this R and D, the recycled paper, etc. composed mainly of cellulose are degraded (saccharified) up to saccharides in a biological method. The saccharides and CO2 obtained are converted into useful substances such as organic acid using the bacterium function. The aim of the R and D is to develop this conversion (bioconversion) technology and to establish the technology to make an effective use of the recycled paper, etc. as useful chemical raw materials/substances and energy. In FY 2000, study was made mostly of the saccharification and bioconversion. As to the saccharification, conducted were the collection of the bacteria for cellulose degrading enzyme production which have been found so far and the evaluation of degradation of the recycled paper. And, as to the bioconversion, conducted were the survey and isolation of enzyme proteins and genes which are concerned in it in the process toward the formation to organic acid from saccharides and CO2, and the analysis of part of them. In this report, introductory remarks were described in Chapter 1. In Chapter 2, the results were summarized of the study on saccharification of the recycled paper. In Chapter 3, the results were outlined of the study on the bioconversion technology. This technology development was aimed at establishing new high efficiency bio-processes. (NEDO)

  7. Achievement report for fiscal 1997 (New Sunshine Project) on the development of superconductor power application technology. Research on a total system / investigative research on introduction effects; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu (New Sunshine keikaku) seika hokokusho. Total system nado no kenkyu / donyu koka no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes investigation and discussion on effects of introducing a superconductor power application technology. The generator sub-committee has compared features, technical problems and development expenses in the first and second proposals, but has not reached the final conclusion. The first proposal is targeted for early realization of 200-300 MW class generators with development cost of six to seven billion yen and a development term of seven years. These developments raise largely towards practical application the levels of material technologies, fabrication and processing technologies, and analysis and design technologies. The second proposal is intended of developing 200-300 MW class generators targeted for increased diameter, as a reduced size machine of a 600-MW generator being a future generator. It will take development cost of eight to nine billion yen with the period of nine years for the development. Majority of the technologies required for developing the future 600-MW class generator can be demonstrated. The AC superconductor device sub-committee has investigated design examples, clarified the specification requirements, and investigated and studied the development measures. The oxide superconductor sub-committee has investigated and studied making wires and conductors, and device application feasibility, but has not reached the stage of presenting specific research and development methods. The practical application strategy sub-committee has also not been able to present a collective measure because of difficulty of making future prospect on the electric power business. (NEDO)

  8. Fiscal 1999 research and verification of geothermal energy exploring technologies and the like. Development of reservoir mass and heat flow characterization (Development of reservoir change prediction technology - Summary); 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho (yoyaku). Choryuso hendo tansaho kaihatsu (choryuso hendo yosoku gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts are exerted to develop technologies for accurately predicting reservoir expansion or other changes through a comprehensive analysis of the fracture hydrology method, gravity monitoring method, electrical and magnetic monitoring method, seismic monitoring method, and their associated technologies. The endeavors cover the development of a post processor system which involves gravity, self-potential, geochemistry, resistivity, etc., and is related to a reservoir simulator, and the development of a reservoir modelling technology. For the development of a post processor system, efforts continue (1) to develop a processor to deal with gravity, self-potential, resistivity, and geochemistry, (2) to carry out basic studies of changes in seismic propagation characteristics, (3) to develop databases, and (4) to develop a simulator interface. Under item (1), development involving gravity, self-potential, and geochemistry is complete, and now manuals are being prepared. A prototype design is complete for resistivity. For the development of a reservoir modelling technology, modelling is under way for the Onikobe and Sumikawa districts. Existing data are taken care of, and productivity predicting simulation is carried out. (NEDO)

  9. Report on a survey in fiscal 1999. Survey on trends in developing innovative technologies related to reducing CO2 emission in departments consuming great quantity of energy, such as petrochemical industry; 1999 nendo sekiyu kagaku kogyo nado energy tashohi bumon ni okeru CO{sub 2} sakugen ni kansuru kakushinteki gijutsu kaihatsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A survey was performed on the state of developing energy saving and CO2 emission reducing technologies in the following fields: (1) distillation technologies, (2) combustion technologies, (3) heat transfer and conduction technologies, and (4) technologies to convert and fix generated CO2. While the technologies in the field (1) are of the matured domain, technologies providing 20 to 60% energy saving effect have been developed. In the field (2), gas turbine combustion can achieve an overall plant thermal efficiency of 50% or more, whereas a trial calculation indicates that CO2 emission can be reduced by 22%. Catalytic combustion is noticed as a measure to make low NOx emission possible. A composite type catalytic combustor for gas turbines demonstrated that NOx emission of less than 5 ppm can be achieved. In the field (3), energy saving effect higher by 52% than in the warm wind room heating system has been obtained. Development has been made on heat storing materials that have phase change temperature of higher than 80 degrees C and large latent heat storage quantity. In the field (4), researches are advanced in a TiO{sub 2} catalyst that uses sunlight. A catalyst that is methanated at high speed with CO2 conversion rate at nearly 100% has been developed. In methanol synthesis, a catalyst that has high selectivity even at low temperatures has been developed. (NEDO)

  10. FY 1999 Report on the technical results. Research and development project for quick-effect type international standards for creating new industries (Standardization of quality and testing methods of automobile fuels and lubricants); 1999 nendo sokkogata kokusai hyojun sosei kenkyu kaihatsu jigyo seika hokokusho. Jidoshayo nenryo nado no seihin hinshitsu shiken hoho no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The research and development project is conducted for the method of evaluating the effects of fuel oils on automobile engines (combustion chamber deposit), testing of valve trains of diesel engines, and testing the effects of gasoline engine oil on oil seal rubber (oil seal compatibility), with the objective to propose the international standards. In the study of the combustion chamber deposit, the combustion chamber deposit method is applied to the road running mode, to clarify that this method is well correlated with the market conditions. In the study of wear of the valve train of diesel engines, the two diesel engine oils, now adopted by the European valve train wear testing method, are applied to the JASO testing method, to clarify that the JASO method is internationally applicable. It is concluded that these two methods can contribute to the international standardization. In the study of the oil seal compatibility, the effects of testing period and engine oil type are investigated, to clarify that this method should be further developed to serve as the international standard. (NEDO)

  11. Report on surveys in fiscal 1999 on technological trends in overseas countries in research and development of the technology to create biological bonding substances utilizing particulates under the industrial and scientific technology research and development theme (university collaborated type); 1999 nendo biryushi riyogata seitai ketsugo busshitsu nado sosei gijutsu no kenkyu kaihatsu kaigai gijutsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the surveys in fiscal 1999 on technological trends in overseas countries in research and development of the technology to create biological bonding substances utilizing particulates. Attendance was made at the U.S. Biochemistry and Molecular Biology '99 to survey signal transmission in cells, new molecules related to gene transcription control, and the mechanisms thereof. A visit was made to the U.S.A. to collect the chromatin research information. In order to analyze efficiently specific biological receptors relative chemical substances, and structure an activity evaluation system, attendance was made at a society meeting in Britain to incorporate the high throughput screening technology. Attendance was made at a publication meeting in the U.S.A. to understand the current status of the DNA micro-array process. Visits were made to American business entities and societies to survey information that contributes to efficient separation and analysis of biological receptors. American business entities and universities were visited to survey the cDNA manifestation library system, technological trends, and researches on intra-living organism systems by using molecular biology. Visits were made to research institutes and societies in the U.S.A. to survey the method for carrying ligands onto latex beads, combinatorial chemistry, and solid phase synthesis. (NEDO)

  12. FY 1998 report on the development of technology for reservoir mass and heat flow characterization. Theme 5-2. Monitoring and modeling of reservoir mass and heat flows (Integrated reservoir modeling and simulation techniques/Modeling support technique); 1998 nendo chinetsu tansa gijutsu nado kensho chosa choryuso hendo tansaho kaihatsu hokokusho (yoyaku). 5-2. Choryuso hendo yosoku gijutsu (modeling shien gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This R and D are aimed at establishing technology to support the reservoir modeling work required for predicting the reservoir variation from the geological/geochemical side. The contents of the development are (1) establishment of the practical measuring system for core fracture system, and (2) establishment of new modeling support technology. In (1), as the core fraction system measuring system, the measurement of fluid inclusion homogenization temperature and melting point and laser Raman spectroscopy were applied to the Wasabizawa area to obtain the results. In (2), the R and D were conducted of a rapid age measuring method for altered rock/unaltered rock and an analytical method for fluid flow using trace chemical components of hydrothermal minerals. In the former, 3-D thermoluminescent intensity of the age-known quartz was measured. The TL age of weak altered rock of Kijiyama dacite in the Wasabizawa area was 320Ka, almost the same result as 320Ka already reported. In the latter, trace components of quartz were measured at each well, and changes in the depth direction were made clear. It was made clear that the variation of Na/K ratio is large around the lost circulation stratum. The geothermal fluid flow was made clear by the analysis of similarity of the intensity ratio. (NEDO)

  13. Fiscal 1999 research and verification of geothermal energy exploring technologies and the like. Development of reservoir change prediction technology (Development of modelling support technology); 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho (yoyaku). Choryuso hendo tansaho kaihatsu (choryuso hendo yosoku gijutsu (modeling shien gijutsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The aim is to develop and popularize techniques relating to geological information such as thermal history. The efforts center about the application of a now-available core fracture measuring system to developed geothermal fields and about the development of new technologies. The measuring system is applied to some core cuttings collected from five boreholes in the Akinomiya district, Akita Prefecture, and the system is used for (1) the evaluation of homogenization temperatures of inclusions in the fluid, (2) the measurement of the points of melting from ice of inclusions in the fluid, and (3) the implementation of laser Raman spectroscopy. Under item (1), it is found that the minimum homogenization temperature of quartz phenocryst in the mother rock or of low-salinity fluid inclusion in a quartz vein is near the current subsurface temperature and that subsurface and reservoir temperatures may be known by evaluating their homogenization temperature. Under item (2), it is found that the NaCl equivalent salinity is distributed in the range of 0.0 to 25wt% and that, in this connection, there is difference between a fluid in a fluid flow and a fluid spurting as thermal water in the Akinomiya district. Under item (3), CO2, N{sub 2}, and CH{sub 4} are detected in most of the boreholes. Efforts are exerted to develop a hydrothermal fluid analyzing technique using a rapid rock dating method and traces of chemical ingredients in hydrothermal minerals. (NEDO)

  14. Fiscal 1997 report of the verification research on geothermal prospecting technology. Theme 5-2. Development of a reservoir change prospecting method (reservoir change prediction technique (modeling support technique)); 1997 nendo chinetsu tansa gijutsu nado kensho chosa. 5-2. Choryuso hendo tansaho kaihatsu (choryuso hendo yosoku gijutsu (modeling shien gijutsu)) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To evaluate geothermal reservoirs in the initial stage of development, to keep stable output in service operation, and to develop a technology effective for extraction from peripheral reservoirs, study was made on a reservoir variation prediction technique, in particular, a modeling support technique. This paper describes the result in fiscal 1997. Underground temperature estimation technique using homogenization temperatures of fluid inclusions among core fault system measurement systems was applied to Wasabizawa field. The effect of stretching is important to estimate reservoir temperatures, and use of a minimum homogenization temperature of fluid inclusions in quartz was suitable. Even in the case of no quartz in hydrothermal veins, measured data of quartz (secondary fluid inclusion) in parent rocks adjacent to hydrothermal veins well agreed with measured temperature data. The developmental possibility of a new modeling support technique was confirmed enough through collection of documents and information. Based on the result, measurement equipment suitable for R and D was selected, and a measurement system was established through preliminary experiments. 39 refs., 35 figs., 6 tabs.

  15. Fiscal 1999 technical achievement report. Research and development project on the quickly effective international standards creation (Standardization of safety of light emitting diode or the like); 1999 nendo sokkogata kokusai hyojun sosei kenkyu kaihatsu jigyo seika hokokusho. Hakko diode nado no anzensei ni kansuru hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Since radiation of a laser diode (LD) is quite different from that of a light emitting diode (LED), evaluating their safety under one and the same standard (criterion) is questionable. The International Electrotechnical Commission (IEC), however, treats them in the same way. For the remedy of such contradiction and for the clarification of difference between the two devices in terms of radiation characteristics, they were quantitatively measured for spatial coherence and further measured for coherence dependency of their beam diameters. Well-supported threshold levels were prepared and biological tests were conducted for proposing a revision of the LED safety standard (IEC). As for the safety of equipment with built-in infrared devices, a measurement method was prepared as IEC61913 and devices are already at the CVD (chemical vapor deposition) stage. The result will be placed before the IEC/TC76 committee for deliberation of IEC60825-1 revision. Furthermore, to establish alignment between IEC and ISO (International Standardization Organization) in terms of laser-aided measurement which is the foundation for such committee deliberation, an ISO/IEC international joint group was created, and a technical recommendation was compiled and presented to the two standardizing organizations. (NEDO)

  16. FY 1999 survey report on the survey on the role and course of the development of technology such as CO2 recovery, fixation and effective use in the industrial policy; 1999 nendo CO{sub 2} kaishu koteika yuko riyo nado gijutsu kaihatsu no sangyo seisakujo no ichizuke oyobi hokosei ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper aims at arranging and assessing the role of themes of the technology development such as CO2 recovery, fixation and effective use in the industrial policy and the results of the development. It also aims at analyzing factors to hinder technology development in comparison with the developmental trend of technology and the role in the industrial policy in foreign countries and at considering the future role in the industrial policy and the course to be taken. Judging from the number of projects and a variety of fields of technology, it could be said that the development of the related technology in Japan is at a top level the same as that in the U.S. In the present conditions, however, most of the technologies are at the stage of the basic research. In many of the research fields except a part like EOR, it is difficult to promote the research only by economical principles, and the government as core needs to promote it. As viewed from an international point, the development/commercialization of technology such as CO2 recovery, fixation and effective use are extremely important from an aspect of not only the heightening of competitiveness in the domestic industry, but Japan's international contribution in the 21st century. (NEDO)

  17. FY 2000 report on the trend survey of technical development of high speed/high function electronic devices such as quantum functional devices in association with the rationalization of energy utilization; 2000 nendo energy shiyo gorika ni kakawaru ryoshika kino soshi nado kosoku kokino denshi device no gijutsu kaihatsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Concerning the results of the R and D made by NEDO of superlattice devices (FY 1981-1990) and quantum functional devices (QFD) (FY 1991-2000) as high speed/high function electronic devices, this survey was aimed at investigating the trend of the newest technology to grasp the technical effects, the state of commercialization/product-making, and the future. The effects, technical subjects, etc. in the R and D of superlattice devices were succeeded to the R and D of QFD as the succeeding project. Here, therefore, the paper arranged the outlook of the commercialization/product-making in relation to the R and D of QFD and the future R and D subjects. In the R and D, features of QFD as target were made clear. The commercialization is limited to Motorola's QMMIC, Fujitsu's RHET, etc. As to the other R and D items, subjects of the technical development to be implemented toward the commercialization just became clear. The subject is the heightening of micro (nano meter) processing technology. The important subject, in particular, is compatibility of the heightening of micro processing and the improvement of throughput. (NEDO)

  18. Report on survey in fiscal 1999 for promotion of geothermal development. Supplementary survey on data processing (fluid inclusion test) for Tsujinodake Area No. B-6; 1998 nendo chinetsu kaihatsu sokushin chosa hokokusho. Data shori ni kakawaru hosoku chosa (ryutai gan'yubutsu shiken nado) No.B-6 Tsujinodake chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-10-01

    This paper reports the fluid inclusion test in the Tsujinodake area in fiscal 1998 for the survey on promotion of geothermal development. The fluid inclusions were classified into three types: those with the maximum value or the average value of the homogenizing temperature agreeing nearly with the saturated boiling curve, those with the homogenizing temperature showing the interim temperature between the present well temperature and the saturated boiling curve, and those agreeing nearly with the present well temperature. It is presumed that the bed temperatures in depths of 1,125.30 m and 1,427.50 m have changed very little since after formation of the present circulating and flowing systems of geothermal waters until now. In contrast at the depth of 1,691.75 m, the bed temperature was estimated to have fallen slightly from that in the most active period of the geothermal water activities. As a result of the rock age measurement, it is estimated that, in the Nansatsu bed groups distributing around the N10-TD-1 well, the temperature has fallen gradually after having been subjected to hot water alteration actions at higher than 200 degrees C, and cooling has taken place down to 200 to 250 degrees C as the fission track date temperature of zircon in the relatively late period (about several hundred thousand years before). There should have been no thermal change that affects the age measurement up to now since then. (NEDO)

  19. FY 2000 report on the R and D of the particulate utilization type creation technology of biological connective substances. Survey of the technical trend overseas; 2000 nendo biryushi riyogata seitai ketsugo busshitsu nado sosei gijutsu no kenkyu kaihatsu seika hokokusho. Kaigai gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper summarized the reports on the results of Japanese engineers' participating in the related scientific meetings held overseas as a survey report on the trend of the overseas technology. The scientific meetings they participated in were: 1) Impact of Genomics on Medicine and Pharmacogenomics Europe (Amsterdam; May 15-26, 2000), 2) Drug Discovery Technology 2000 (Boston; August 10-20, 2000), 3) Biotechnology 2000 (Berlin; September 3-12, 2000), 4) PacificChem 2000 (Hawaii; December 14-21, 2000), 5) 4th Winter Conference on Medicinal and Bioorganic Chemistry (Seattle; January 27 - February 4, 2001). Impact of Genomics on Medicine was composed of the following five fields: microarrays, proteomics, functional genomics and target validation, genetic variation technology, and applications of SNP analysis (joint session). Pharmacogenomics Europe was composed of the following four fields: applications of SNP analysis (joint session), SNP assays, targets and compounds, and clinical applications. (NEDO)

  20. FY 1999 report on the results of the study to support the commercialization of recycling technology, etc. 4. R and D for enhancement of automobile fuel consumption/exhaust gas technology; 1999 nendo recycle gijutsu nado jitsuyoka shien kenkyu seika hokokusho. 4. Jidosha nenpi hai gas gijutsu kodoka kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of clarifying measures for reducing fuel consumption and exhaust gas of automobiles, survey was made of effects of environmental temperatures and fuel properties on exhaust gas. In the survey of effects of environmental temperatures, experiment on exhaust gas was carried out by changing the laboratory temperature from 5 degrees C to 35 degrees C using direct injection gasoline engine. As a result, it was found out that environmental temperatures have effects exhaust gas according to changes in purification rate by rise in catalytic temperature, changes in air/fuel ratio by changes in air density, control methods to secure starting-up/drivability, etc. In the survey of effects of gasoline properties, study was made on effects of distillation properties, especially, 90% distillation temperature (T90) on exhaust gas. As a result, in 10(center dot)15 mode, CO and THC decreased with a decrease in T90 both in three-way catalytic car and direct injection car. Especially, CO decreased to about 1/4 when decreasing T90 from 151 degrees C to 116 degrees C. NOx increased in three-way catalytic car and decreased in direct injection car with a decrease in T90. (NEDO)

  1. Report for fiscal 2000. Part 4. Research on assistance to put recycling technologies into practical use (Research and development of elevating automotive fuel consumption and exhaust gas technologies); 2000 nendo recycle gijutsu nado jitsuyoka shien kenkyu hokokusho. 4. Jidosha nenpi hai gas gijutsu kodoka kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Discussions have been given on identification of actual status of exhaust gas emission during driving, starting, and idling of automobiles, on technologies to enhance fuel consumption and reduce exhaust gas emission, and on technologies to measure harmful substances. In the investigation of effects of environmental temperatures on evaporation gas, it was shown that fuel evaporation generated from the fuel tank increases as the average ambient temperature rises. In the investigation of effects of environmental temperatures on exhaust gas and fuel consumption, it was discovered that the effects of environmental temperatures on 10{center_dot}15 mode regulated exhaust gas differ depending on vehicles, and no definite difference due to combustion systems was recognized. Carbon monoxide and THC under the 11 mode regulation showed a trend to increase when the environmental temperature falls down. In the investigation of effects of fuel properties on exhaust gas, no definite difference due to combustion systems was recognized as a result of measurements using various types of gasoline having different distillation properties. In the investigation of analysis methods for harmful substances, development has been made on an analysis method mainly for 1-3 butadiene. (NEDO)

  2. FY 1999 report on the results of the R and D of the global environmental industry technology. R and D of the CO2 fixation/effective use technology using bacteria/algae; 1999 nendo saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing the technology to fix CO2 and recycle it as resource in higher efficiency than that in photosynthesis in the nature world, study of bacteria, etc. was made in terms of the search, breeding, and artificial realization of the growth environment, etc. The FY 1999 results were summed up. As to high efficiency photosynthetic bacteria/microalgae, conditions for sampling/breeding/optimum culture of bacteria were established and made database. From conditions for the optimum CO2 fixation by photosynthetic bacteria, oxygen injury prevention culture method, continuous culture experiment, etc., it was found out that the carbyne cycle was a main route of the carbon fixation also in photosynthetic bacteria. As to the cell fusion, established were the technology of electric fusion of interspecific fusion strains and the technology of evaluation of growth characteristics. Also studied was a method to transfect genes into Chlorella sp. which fixes CO2. Concerning the light collecting reactor of 200L scale, a high concentration culture experiment was carried out using Chlorella sp. UK001 as the strain tested, and the engineering data on the behavior in culture tank, multiplication speed, etc. were collected. (NEDO)

  3. Industrial technology research and development project for global environment in fiscal 1998. Report on achievements in research and development of technologies for fixation and effective utilization of carbon dioxide by utilizing bacteria and algae; 1998 nendo saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Microorganisms are cultivated industrially in a great quantity to fix CO2 at efficiency higher than that of photosynthesis in natural world to develop technologies to re-utilize them as resources. This paper describes achievements in fiscal 1998. Existing strain samples of photosynthesized bacteria and micro-algae were screened to continue discussions on optimal culture conditions, and evaluation on properties. Genes that provide Chlorella with antibiotic resistance were introduced to have performed evaluation on function manifestation, and acquired enzymatic genes of unsaturated {omega} 3. Using green algae as the object, reduction in the processing time has resulted in acquiring a large number of fused cell colonies. Discussions were given on conditions to breed photosynthesized bacteria and fix CO2. Structural analyses were performed on CA protein as an enzyme related to take CO2 into living organisms, and on genes. Developments were carried out on a photosynthesizing bio-reactor and useful substance producing technologies on a continual basis. A 200-liter scale light collection type bio-reactor improved the fixing capacity by 30% in Chlorellas by changing the culture medium. The direct light receiving panel type bio-reactor can utilize even scattered light, with its fixing capacity per installation area exceeding the target. Fundamental data were acquired with Chlorellas on utilizing feeds, fertilizers and building materials. (NEDO)

  4. Report on achievements in fiscal 1999 on research and development of the technology to create biological bonding substances utilizing particulates under the industrial and scientific technology research and development theme [university collaborated type]. Research and development of the technology to create biological bonding substances utilizing particulates; 1999 nendo biryushi riyogata seitai ketsugo busshitsu nado sosei gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the achievements in fiscal 1999 on development of the technology to create biological bonding substances utilizing particulates. In fixing ligands onto particulates, it is necessary that various compounds be fixed with their receptor bonding specificity maintained. Therefore, carboxylic acid, thiol and bromoacetyl groups were introduced into the particulates. Capping them by using methoxyacetyl was found capable of suppressing non-specific adsorption. Opioid compounds were synthesized for their fixation onto particulates for selection and separation. Carrying particulate bonding precursors in latex beads was realized. Synthesis will continue on opiod compounds in which amide groups are introduced into different positions to provide the particulate carrying ligands with diversity. Biological receptors for different compounds were obtained and refined by using compound fixing particulates. Refinement and acquisition were possible on FK506 bonded protein in a short time from cell extraction liquid by using the fixing particulates for the FK506 bonded protein. The paper also describes analysis of bonded domains, and position-specific fixation of the biological receptors. (NEDO)

  5. Achievement report for fiscal 1999 on research and development of technologies for medical welfare equipment. Surgery support system for brain tumors and other conditions (Rationalization for energy profit); 1999 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu seika hokokusho. Noshuyo nado shujutsu shien system (energy shiyo gorika)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    In the second phase of experimental micro-manipulator fabrication, insertion parts equipped with three manipulators and operation input units are built and evaluated. The system comprises three input units and a console with a built-in controller etc., and the console is checked for shape and operability. A high resolution and high brightness stereoscopic viewer is developed for clinical use by surgical operators, and is examined for practicality. The positioning system for the intraoperative vision instrument are improved relative to its attachment method, accuracy, and sterilization tolerance. The result is evaluated, and then further improvement is made. Some functions are added to the surgical planning software program. Software programs are constructed for the real-time control and operation of the viewing system. For the micro-manipulator system to serve as a total system, the forceps are extended, tips are developed for the suction device and incision device, and their functions as members of the system are evaluated. (NEDO)

  6. FY 1999 achievement report on the supporting project to form energy/environmental technology verification project - International joint verification research project. Development of the mean wind velocity prediction method and the related matters in developing countries; 1999 nendo hatten tojokoku ni oikeru heikin fusoku yosoku shuho nado no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Developing countries have no sufficient basic data for the analysis of meteorological conditions including wind characteristics, and there are problems in adopting simulation models there. Accordingly, the revision/development of simulation models were conducted, considering characteristics of models to predict wind characteristics from topographical/geographical aspects and widely meteorological aspect in Myanmar. At the same time, the mean wind velocity distribution chart for Myanmar was drawn up by observing wind characteristics domestically in Myanmar, by comparing the predicted results using the above-mentioned models and the measured data, and by verifying the simulation results. The items for development are as follows: (1) To make simulation models for wind characteristics in the whole Myanmar based on the information obtained from the meteorological observation system for prediction of the mean wind velocity. Also to verify the simulational results using the measured data on wind characteristics at specified points. (2) To conduct the developmental work under a research system jointly with the counterpart and to produce favorable results as an international joint research. (3) To acquire the basic data to find the relation between the photovoltaic power generation and wind characteristics for studying hybrid type power systems for renewable energy in the future. (NEDO)

  7. Basic investigation on promotion of joint implementation in fiscal 2000. Investigations on development of technology to utilize heat of deep earth pressure type hot water in Hungary; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Hungary koku shinso chiatsugata onsui no netsuriyo gijutsu kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Investigations and discussions were given on a project to implement district heating, greenhouse heating, and binary power generation by utilizing geothermal resources in Hungary. Hungary has deep earth pressure type hot water areas distributed, that flow hot water of about 90 to 180 degrees C by the bed pressure. The areas that can utilize the hot water were extracted and investigated by using literatures and data. The project plans district heating of about 15,000 households using the geothermal water, heating of greenhouses equivalent to 100,000 m{sup 2}, gas engine power generation by using the flowing fluid pressure and combustion of the generated methane gas, and binary power generation by using the geothermal water. As a result of the discussions, it was revealed that the energy saving effect would save 5,008 Ktoe in 20 years as converted to crude oil, and the greenhouse effect gas reducing effect would reduce 14.2 million t-CO2 in 20 years. The total project cost would be about 16.62 billion yen. The internal profit rate of this project is 11.34%, largely exceeding the opportunity cost, and indicating the financial effect possibility. (NEDO)

  8. FY 1996 report on the results of the development of superconductor power application technology. Study of a total system, etc. (Investigational study of the introductory effect); 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Total system nado no kenkyu (donyu koka no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Under the secondary interim assessment made in FY 1995 between the assessment committee of the energy/environment technology development sectional meeting of the Industrial Technology Deliberation Council and NEDO, in this project, the following were conducted in FY 1996: study of trial manufacture of superconductor motor model machine and R and D of element technology (conductor technology/refrigerator technology). The study was proceeded mainly with Super-GM, and as to the motor, the preparation for test on a part of the model machines was finished. Considering FY 1998 which is the final year of this project, the investigational study in FY 1996 aims at accumulating/arranging/analyzing the data which help judge how to proceed with the future R and D of superconductor power application technology continuously based on the secondary interim assessment. For superconductor motor and various superconductor power appliance, economical/technical feasibilities and methods of R and D and surveys of trends in Japan and abroad for the R and D were made important items. Further, 'R and D of the basement of superconductor power application' proposed in the secondary interim assessment (R and D of the combination of elements which become the basement of equipment technology over a stage of parallel R and D of element technology of conductor, etc.) targeted the presentation of concrete details. (NEDO)

  9. Fiscal 1998 industrial science and technology R and D theme (University coordination type). Research report on R and D of technologies for creating new bioaffinity molecules using submicron beads; 1998 nendo biryushi riyogata seitai ketsugo busshitsu nado sosei gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes the fiscal 1998 result on the entrusted research 'R and D of technologies for creating new bioaffinity molecules using submicron beads' based on 'Industrial science and technology R and D system.' As for development of technologies for analyzing chemical- biomolecule complexes using submicron affinity beads, for molecule design of DNA to be connected with cisplatin, telomere DNA was employed as a target DNA of cisplatin, and cisplatin-modified DNA (Pt-DNA) was synthesized. Reaction condition for Pt-DNA connected beads was established, and affinity beads with Pt-DNA were prepared. As for development of organic receptor refining technology, proteins bound to cisplatin-DNA were preliminarily analyzed, showing that the Pt-DNA is a proper target chemical substance. It is the first evidence that certain proteins recognize cisplatin-damaged telomere DNA. In addition, introduction of the equipment for developing analysis technology of binding domains, development of technology to create organic receptors with new functions, and general research on the titled technologies were carried out. (NEDO)

  10. Research and development of technologies for CO{sub 2} fixation and effective utilization thereof, etc., in fiscal 1998. Report on research and development of technologies for the effective use of CO{sub 2} by virtue of contact hydrogenation (CO{sub 2} separation and recovery system of the next-generation type); 1998 nendo nisanka tanso koteika yuko riyo gijutsu nado kenkyu kaihatsu jigyo. Sesshoku suisoka hanno riyo nisanka tanso yuko riyo gijutsu kenkyu kaihatsu jigyo kenkyu kaihatsu jigyo (jisedaigata shoene CO{sub 2} bunri kaishu system ni kansuru chosa kenkyu hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researches were conducted for the goal of proposing a totally new process enhanced in efficiency and energy saving, and capable of CO2 separation. In fiscal 1997, hydrocarbon materials were reformed by oxygen separated within a system allowing fuel cells to generate power efficiently, when all the emitted CO2 was separated and recovered within the system. Furthermore, cold heat was utilized for the acquisition of liquefied CO2 gas products. A part of oxygen separated at the fuel cell cathode was recycled into the combustion section external to the tubular reaction reformer, and CO2 was separated by mere cooling from the combustion products for the simultaneous production of by-products such as high-purity nitrogen gas and liquefied CO2 for a great improvement in economy. In fiscal 1998, the system was improved. Proposed then was a new system in which an oxygen partial oxidation type reformer assumed the nuclear role, separating all the oxygen at the cathode, reusing part thereof for oxygen enrichment, and feeding the rest thereof into the reformer. The design realized the recycling of the whole of the products of the two cell electrodes into the reformer for the maximum reuse of the products of the hydrogen/oxygen separation function. (NEDO)

  11. Aplicación de volúmenes de nado para las categorías 11 - 12 y 13 -14 años de los atletas de la escuela de natación de Pinar del Río

    Directory of Open Access Journals (Sweden)

    Zaylen Serralta Hernández

    2011-12-01

    Full Text Available La presente investigación es un estudio realizado con los atletas de las categorías 11-12 y 13-14 años de La Escuela de Natación de Pinar de Río, tomando como muestra a todos los alumnos de estas categorías a partir del curso 2007-2008. Se analiza detalladamente los volúmenes de nado propuestos por el Programa de Preparación del Deportista (PPD, donde se aprecia que los atletas de la provincia no logran cumplir lo indicado por el mismo, siendo el inicio tardío en la práctica del deporte, la carencia de piscinas con un funcionamiento estable y las bajas temperaturas en el periodo invernal, los que más afectan el proceso. Provocando esto que no se alcancen resultados satisfactorios y con ello desmotivación y deserción por parte de los alumnos. La aplicación de los nuevos volúmenes inferiores a los PPD nos permitió obtener una mejor progresión y resultados satisfactorios en los eventos que se participa en las distintas competencias.

  12. Efecto del D-004, un extracto del fruto de Roystonea regia y omega-3 en el modelo de nado forzado en ratones Effect of D-004, a fruit extact from Roystonea regia and Omega-3 in a model of forced swimming in mice

    Directory of Open Access Journals (Sweden)

    Daisy Carbajal Quintana

    2010-03-01

    Full Text Available La depresión se encuentra entre las principales causas de morbilidad y mortalidad de la población adulta y su manejo farmacológico incluye, entre otras opciones alternativas, el uso de la medicina complementaria, como es el caso del aceite de pescado rico en ácidos grasos omega-3 (AGw3. El D-004, extracto lipídico de los frutos de la palma real (Roystonea regia que consiste en una mezcla de ácidos grasos, ha mostrado poseer una moderada acción antidepresiva. El objetivo de este trabajo consistió en comparar los efectos del tratamiento oral con D-004, con los AGw3 y con su terapia combinada en el modelo del nado forzado en ratones. Para ello, ratones machos se distribuyeron en 8 grupos: uno control tratado con el vehículo, dos con D-004 (250 y 500 mg/kg , dos con AGw3 (250 y 500 mg/kg, dos con la combinación y uno con imipramina (10 mg/kg i.p.. Todos los tratamientos disminuyeron significativamente el tiempo de inmovilidad con respecto al control, sin diferencias entre dosis similares de los respectivos tratamientos. En conclusión, el D-004, los AGw3 y su terapia combinada resultaron igualmente efectivos en reducir el tiempo de inmovilidad de los ratones, sin manifestarse efectos aditivos o sinérgicos con la administración conjunta de ambas sustancias.Depression is among the major causes of morbidity and mortality of adult population and its pharmacologic management includes among other alternative options, the use of the complementary medicine, e.g. the fish oil rich in Omega-3 fatty acids (AGw3. The D-004, a lipid extract of Real Palm fruits (Roystonea regia consisting of a fatty acid mixture, has a moderate antidepressant action. The aim of present paper was to compare the effects of oral treatment using D-004 with the AGw3 and with its combined therapy in forces swimming in mice. Thus, the male mice were distributed into 8 groups: one as control treated with vehicle, two with D-004 (250 and 500 mg.kg, two with AGw3 (250 and 500

  13. Ne nado obizhatsja na Karzaja / Sven Mikser

    Index Scriptorium Estoniae

    Mikser, Sven, 1973-

    2008-01-01

    Afganistani presidendi Hamid Karzai arvates on liitlasvägede Helmandi provintsis viibimise ajal olukord provintsis halvenenud. Autori arvates on Eesti rahukaitseväed teinud oma tööd Afganistani olukorra stabiliseerimisel hästi, ja seda jätkatakse

  14. Troihh nado ubrat, reshil komissar / Boris Tuch

    Index Scriptorium Estoniae

    Tuch, Boris, 1946-

    2004-01-01

    4. märtsil esilinastus mängufilm "Täna öösel me ei maga" : stsenaristid Kristian Taska, Jaan Tätte : režissöör Ilmar Taska : operaator Istvan Borbas : produtsent Kristian Taska : peaosades Carmen Kass, Peter Franzen; Maria Avdjushko, Priit Võigemast : Taska Productions

  15. FY 1999 Report on the results of technological development of machine tools for rationalization of energy utilization. Development of a lathe with high precision and conservation of energy using natural phenomenon (Thermal countermeasure using self compulsory cooling and thermal insensitive structure - results of the first year); 1999 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Shizen gensho wo takumi ni oyoshita sho energy koseido senban no kaihatsu (self kyosei reikyaku to netsufukan gijutsu wo mochiita netsuhenkei yokusei taisaku - dai 1 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A lathe, which is a central tool in a factory of automobiles or home electric appliances, tends to suffer decreased machining precision resulting from thermal deformation. This project is aimed at development of the energy-saving, high-precision lathe technologies using self compulsory cooling and thermal insensitive technologies as the countermeasures against the thermal deformation. The self compulsory cooling is a method of cooling by evaporation of water with an evaporative, water-absorptive cloth being bonded to a machine tool surface around the major axis. The thermal insensitive technologies include the three-dimensionally zero-center design technologies which help design a lathe in such a way to set the processing point (tool working point) at the base of thermal deformation in the X, Y and Z axis directions; material combination technologies to control thermal deformation; and coloring technologies to control thermal deformation. The development target is the high-precision lathe fabrication technologies, which realize a temporal precision change of 1 to 2 {mu}m or less per work dimension of 100mm. The activities cover 5 areas, including development of elementary technologies for each item and construction/evaluation of the full-size test unit. (NEDO)

  16. FY1995 formation of a global database of color-related sensory values such as color cognition and color emotions and the research and development of a multimedia system for feedback of such values onto the color design of products and living environments; 1995 nendo shikisai ninchi ya shikisai kanjo nado, shikisai ni taisuru kannochi no kokusaiteki database no kochiku to, sore wo seihin oyobi seikatsu kankyo no shikisai sekkei ni han'eisaseru multimedia system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Research was conducted with the aim of provide small and medium enterprises as well as consumers with (1) information concerning color on a global scale and (2) technical support for the color planning of homes and apparel. (1) In 20 major countries (23 regions), color-related sensory evaluations were carried out and simultaneous fact-finding studies to investigate the use of colors in homes and apparel were conducted, after which a database was built containing color information according to country (region). (2) Using the above data together with data from color evaluation experiments, a model formula was obtained for measuring the amenity of colors. (3) This formula was employed to develop software for evaluating the amenity of colors by computer. (4) A multimedia system was built that permits shared use of the results of (1) through (3) above. (NEDO)

  17. Fiscal 1998 achievement report on regional consortium research and development project. Research and development for developing basic technologies of composite laser-aided metal machining into highly advanced system (Technology of machining process systematization for furnishing titanium and titanium alloys with advanced functions - 2nd year); 1998 nendo fukugo laser nado ni yoru kinzoku kako kiban gijutsu no kodo system ka no kenkyu kaihatsu seika hokokusho. 2. Chitan oyobi chitan gokin eno kokino fuyo kako system ka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the creation of new industries and for their expansion to the consumer market, efforts are made to develop laser-aided technology of bonding titanium with other metals and CAD/CAM (computer-aided design/computer-aided manufacture)-aided technology of high-precision multidimensional laser machining for titanium. In the development of technology for bonding titanium and other metals, combinations of titanium and stainless steel and titanium and copper are examined, and a dissimilar metal joint is successfully manufactured, free of cracks at a tension shear strength level of approximately 4200N/40mm and shear stress of 200MPa or higher. In the study of the mechanism of bonding, it is found that a sound weld metal is created with the formation of intermetallic compounds well inhibited by allowing titanium to be on the upper surface. In the study of laser-aided titanium cutting, a dross-free cutting process is realized by optimizing cutting conditions such as those involving laser excitation and assist gas application. Three-dimensional laser-aided cutting is carried out in compliance with a 3-dimensional laser cutting program incorporating metal pattern data, and the process is found to reduce the number of necessary dies to 1/4 to shorten and simplify the process. (NEDO)

  18. FY1995 formation of a global database of color-related sensory values such as color cognition and color emotions and the research and development of a multimedia system for feedback of such values onto the color design of products and living environments; 1995 nendo shikisai ninchi ya shikisai kanjo nado, shikisai ni taisuru kannochi no kokusaiteki database no kochiku to, sore wo seihin oyobi seikatsu kankyo no shikisai sekkei ni han'eisaseru multimedia system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Research was conducted with the aim of provide small and medium enterprises as well as consumers with (1) information concerning color on a global scale and (2) technical support for the color planning of homes and apparel. (1) In 20 major countries (23 regions), color-related sensory evaluations were carried out and simultaneous fact-finding studies to investigate the use of colors in homes and apparel were conducted, after which a database was built containing color information according to country (region). (2) Using the above data together with data from color evaluation experiments, a model formula was obtained for measuring the amenity of colors. (3) This formula was employed to develop software for evaluating the amenity of colors by computer. (4) A multimedia system was built that permits shared use of the results of (1) through (3) above. (NEDO)

  19. Comportamento de variáveis fisiológicas em atletas de nado sincronizado durante uma sessão de treinamento na fase de preparação para as Olimpíadas de Atenas 2004 Comportamiento de variábles fisiológicas en atletas de nado sincronizado durante una sesion de entrenamiento en la fase de preparación para las Olimpíadas de Atenas 2004 Behavior of physiological variables in synchronized swimming athletes during a training session preparing for the Athens 2004 Olympic Games

    Directory of Open Access Journals (Sweden)

    Marina Guimarães Antunes Pazikas

    2005-12-01

    Full Text Available O objetivo do presente estudo foi avaliar o comportamento de variáveis fisiológicas durante uma sessão de treino de nado sincronizado realizada na fase de preparação para as Olimpíadas de Atenas 2004. MATERIAIS E MÉTODOS: A amostra utilizada foi constituída pelo dueto (24 ± 0 anos representante do Brasil em Atenas 2004. A coleta de dados foi realizada durante uma sessão de treinamento com duração de 198 minutos. O treino se iniciou com a parte física, seguida da parte técnica. Para a determinação da glicemia e da concentração de beta-hidroxibutirato foi utilizado o monitor Optium® com suas respectivas tiras. As concentrações de cortisol e das enzimas lactato desidrogenase (LDH e creatina quinase (CK foram determinadas por radioimunoensaio (DPC© e kits comerciais (CELM®, respectivamente. O acompanhamento da freqüência cardíaca (FC foi realizado com o freqüêncimetro Advantage Polar®. RESULTADOS: Foi observada redução (~2% do peso corporal. A glicemia também apresentou queda (~30% em comparação ao valor obtido no início do treino. Em contrapartida, foi observada elevação na concentração de cortisol (salivar 22% e plasmática 29% e de beta-hidroxibutirato (~340%. Não foi observada alteração significativa na concentração plasmática de CK e de LDH. O acompanhamento da FC demonstrou que dos 198 minutos que constituíram a sessão de treino, 36,5 ± 0,7 minutos foram realizados em intensidade leve; 103,5 ± 0,7 minutos em intensidade moderada, 54,0 ± 2,1 minutos em intensidade alta e 4,0 ± 0,0 minutos em intensidade muito alta. CONCLUSÕES: A perda de peso indica que a reposição hídrica não foi adequada. A redução na glicemia e o aumento na concentração de corpos cetônicos e de cortisol reforçam a importância da suplementação de carboidrato durante o treino de longa duração. O comportamento da FC demonstra que a sessão de treinamento foi realizada em uma intensidade moderada, porém com

  20. Proposta de teste incremental baseado na percepção subjetiva de esforço para determinação de limiares metabólicos e parâmetros mecânicos do nado livre Propuesta de un test adicional basado en la percepción subjetiva del esfuerzo para determinar los límites metabólicos y los parámetros mecánicos del nado libre Incremental test proposal based on the rating of perceived exertion to determine metabolic thresholds and mechanical parameters of free style

    Directory of Open Access Journals (Sweden)

    Manoel Carlos Spiguel Lima

    2006-10-01

    Full Text Available A percepção subjetiva de esforço (PSE é determinada de forma não invasiva e utilizada juntamente com a resposta lactacidêmica como indicadores de intensidade durante teste incremental. Em campo, especialmente na natação, há dificuldades nas coletas sanguíneas; por isso, utilizam-se protocolos alternativos para estimar o limiar anaeróbio. Assim, os objetivos do estudo foram: prescrever um teste incremental baseado na PSE (Borg 6-20 visando estimar os limiares metabólicos determinados por métodos lactacidêmicos [ajuste bi-segmentado (V LL, concentração fixa-3,5mM (V3,5mM e distância máxima (V Dmáx]; relacionar a PSE atribuída em cada estágio com a freqüência cardíaca (FC e com parâmetros mecânicos de nado [freqüência (FB e amplitude de braçada (AB], analisar a utilização da escala 6-20 na regularidade do incremento das velocidades no teste e correlacionar os limiares metabólicos com a velocidade crítica (VC. Para isso, 12 nadadores (16,4 ± 1,3 anos realizaram dois esforços máximos (200 e 400m; os dados foram utilizados para determinar a VC, velocidade de 400m (V400m e a freqüência crítica de braçada (FCb; e um teste incremental com intensidade inicial baseada na PSE, respectivamente, 9, 11, 13, 15 e 17; sendo monitorados em todos os estágios a FC, lactacidêmia e os tempos de quatro ciclos de braçadas e das distâncias de 20m (parte central da piscina e 50m. Posteriormente, foram calculadas as velocidades dos estágios, FB, AB, V LL, V3,5mM e V Dmáx. Utilizaram-se ANOVA e correlação de Pearson para análise dos resultados. Não foram encontradas diferenças entre VC, V Dmáx e V LL, porém a V3,5mM foi inferior às demais velocidades (P La Percepción Subjetiva del Esfuerzo (PSE es determinada de forma no invasiva y utilizada juntamente con la respuesta lactacidémica como indicadores de intensidad durante un test de incremento. En campo, especialmente en la natación, hay dificultades en las colectas

  1. Subsurface displacement of the Tachikawa fault; Tachikawa danso no chika shinbu ni okeru danso hen`i

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, K; Kano, N; Kiguchi, T; Tanaka, A [Geological Survey of Japan, Tsukuba (Japan); Sato, H [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute

    1997-10-22

    Seismic exploration using the reflection method was carried out at the central section of the Tachikawa fault located in the western part of the Musashino high plain spreading over Tokyo and Saitama Prefectures. The course of traverse was set on a road running in the east to west direction, which crosses the running direction of the Tachikawa fault in Sunagawa, Tachikawa City by about 65 degrees. The area near the course of traverse is a terraced alluvial fan, with the nature of its surface soil consisted of a gravelly bed of the Quaternary period. In order to identify the fault structure in detail, the focal point interval was set to 5 m, being half of the vibration receiving point interval of 10 m. The CMP was defined at a 2.5-m interval rather than a 5-m interval. The S/N ratio of the derived data was found not good. This is because of scattering of seismic energy into the gravelly bed with a thickness of about 100m in the shallow portion and because of noise from passing vehicles. The data processing was applied with correlation, geometry, static correction, velocity analysis and CMP polymerization to have prepared a preliminary CMP polymerization time cross section. As a result, it was elucidated that the Tachikawa fault forms a bend zone or a crush zone under the ground, and continues down to a great depth at a high angle. 9 refs., 3 figs.

  2. Deep sedimentary structure model beneath the Osaka plain; Osaka heiya ni okeru shinbu chika kozo no model ka

    Energy Technology Data Exchange (ETDEWEB)

    Miyakoshi, K; Kagawa, T; Echigo, T [Osaka Soil Test, Osaka (Japan)

    1997-05-27

    Restructuring was carried out on a sedimentary basin structure model of the Osaka plain including Osaka Bay by using newly obtained underground structural data. After the Hygoken-nanbu Earthquake of 1995, a large number of underground structure investigations have been performed in Osaka Bay and urban areas of Kobe and Osaka. However, very few surveys have been done in areas peripheral to Osaka Prefecture, such as the Ikoma area. Therefore, an attempt has been made to increase the number of measuring points to acquire underground structural data of these areas. Estimation of basic rock depths has utilized the dominant cycles in H/V spectra obtained from micro vibration survey, and good correlation of the base rock depths derived by a refraction exploration and a deep-bed boring investigation. With regard to bed division and P- and S- wave velocities in sedimentary beds in the Osaka sedimentary basin, an underground structure model was prepared, which was divided into four beds according to the refraction exploration and the micro vibration investigation. Data obtained by using this model agreed well with depth data acquired from physical exploration and other types of investigations. However, no good agreement was recognized in the data for such areas where the basic depth changes abruptly as the Rokko fault and the Osaka bay fault. 6 refs., 8 figs., 2 tabs.

  3. Deep geological strucure of a volcano verified by seismic wave. Jishinha de mita kazan no shinbu kozo

    Energy Technology Data Exchange (ETDEWEB)

    Hasegawa, A. (Tohoku University, Sendai (Japan). Faculty of Science)

    1991-09-01

    Three dimensional structure of seismic wave velocity for the crest and upper mantle under the North East Japan is determined by the seismic tomography which is prepared by the natural earthquakes confirmed by the observation network for micro earthquakes, indicating that the low velocity region exists just under the corresponding volcano to the upper mantle. Further, the following contents can be verified: Any micro earthquakes which are verified by the above observation network and occur at the depth of 25-40km show the lower generation rate less than 1% and the low dominant frequency compared with the conventional inland earthquake(lower limit of depth is 15km) in the same region and occur around volcanos. The existence of the remarkable reflection surface for S wave which is found at the depth of 10-20km seems to be caused by the melting mass. The above mentioned low velocity region is estimated to correspond to the lifting region of high temperature magma, micro earthquakes of low frequency to the magma activity around that magma and the reflection surface for S wave to the part of the magma. 8 refs., 4 figs.

  4. Research and development of a color-related global database of sensory values concerning color cognition, color emotions, etc. and the multimedia system to feedback it into products and living environment. FY 1995 data book 3 (2) 'Color cognition of the world's youth' analysis and mapping; 1995 nendo shikisai ninchi ya shikisai kanjo nado, shikisai ni taisuru kannochi no kokusaiteki database no kochiku to, sore wo seihin oyobi seikatsu kankyo no shikisai sekkei ni han'eisaseru multimedia system no kenkyu kaihatsu. Shiryoshu dai 3 kan (2) 'sekai no seinen no shikisai ninchi chosa' shiryohen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    An investigational study was conducted for the youth of main 20 cities of the world including Japan, aiming at clarifying characteristics of the color sense and at constructing a color-related global database and studying how to use it. This data is the results of the analyses and mapping. The following were included as data: calculational results of the mapping by country (all items), calculational results of the similarity analysis of countries (regions), regional clusters of color taste and characteristics of each cluster, international comparison of memory color in the natural world, analysis of regional difference in warm-cold/light-heavy/loud-quiet images, analysis of color association data by language, analysis of image maps by factor analysis, regional difference in color association concerning 15 languages, analysis of regional difference in color association data by language, analysis of regional difference in colors which have been most enjoyed/colors peculiar to cities, international comparison of evaluation of 2-color coloring matching degrees, and international comparison of evaluation of coloring matching degrees. (NEDO)

  5. Research and development of a color-related global database of sensory values concerning color cognition, color emotions, etc. and the multimedia system to feedback it into products and living environment. FY 1995 data book 7 Color amenity calculating system; 1995 nendo shikisai ninchi ya shikisai kanjo nado, shikisai ni taisuru kannochi no kokusaiteki database no kochiku to, sore wo seihin oyobi seikatsu kankyo no shikisai sekkei ni han'eisaseru multimedia system no kenkyu kaihatsu. Shiryoshu dai 7 kan shikisai kaitekido keisan system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    A color amenity calculating system was developed. The paper described the details, calculating method, verification, etc. of the system. This calculating system automatically calculates the score of amenity for color of the specified image, and the application field is 'exterior/appearance of building and streets,' 'interior,' and 'fashion.' Elements composing color amenity are the matching degree, familiarity, lightness, brightness and unity of colors. The weighed average value of these becomes general color amenity. Based on 'the survey of the world's youth,' color amenity is calculated by area, assuming that people in 23 areas of 20 countries in the world have different amenity by male/by female. In the system, objects are called up by 'input of stimulus,' and color information of images is numerated by 'measurement of color distribution.' In 'selection of parameters,' it is clarified whom the amenity is for (by country/by sex). The calculation is made instantaneously, indicating the result on the screen. (NEDO)

  6. Research and development of a color-related global database of sensory values concerning color cognition, color emotions, etc. and the multimedia system to feedback it into products and living environment. FY 1995 data book 7 Color amenity calculating system; 1995 nendo shikisai ninchi ya shikisai kanjo nado, shikisai ni taisuru kannochi no kokusaiteki database no kochiku to, sore wo seihin oyobi seikatsu kankyo no shikisai sekkei ni han'eisaseru multimedia system no kenkyu kaihatsu. Shiryoshu dai 7 kan shikisai kaitekido keisan system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    A color amenity calculating system was developed. The paper described the details, calculating method, verification, etc. of the system. This calculating system automatically calculates the score of amenity for color of the specified image, and the application field is 'exterior/appearance of building and streets,' 'interior,' and 'fashion.' Elements composing color amenity are the matching degree, familiarity, lightness, brightness and unity of colors. The weighed average value of these becomes general color amenity. Based on 'the survey of the world's youth,' color amenity is calculated by area, assuming that people in 23 areas of 20 countries in the world have different amenity by male/by female. In the system, objects are called up by 'input of stimulus,' and color information of images is numerated by 'measurement of color distribution.' In 'selection of parameters,' it is clarified whom the amenity is for (by country/by sex). The calculation is made instantaneously, indicating the result on the screen. (NEDO)

  7. Research and development of a color-related global database of sensory values concerning color cognition, color emotions, etc. and the multimedia system to feedback it into products and living environment. FY 1995 data book 3 (1) 'Color cognition of the world's youth' analysis and mapping; 1995 nendo shikisai ninchi ya shikisai kanjo nado, shikisai ni taisuru kannochi no kokusaiteki database no kochiku to, sore wo seihin oyobi seikatsu kankyo no shikisai sekkei ni han'eisaseru multimedia system no kenkyu kaihatsu. Shiryoshu dai 3 kan (1) 'sekai no seinen no shikisai ninchi chosa' bunseki kekka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    An investigational study was conducted for the youth of main 20 cities of the world including Japan, aiming at clarifying characteristics of the color sense and at constructing a color-related global database and studying how to use it. This data is the results of the analyses. In the analysis of all items, the following were indicated: color mapping by country, analysis of similarity of countries, relations between 'the survey of the world's youth' and the internet survey, etc. In the analysis of each item, the following were shown: regional difference in color of hair/color of pupil/color taste, analysis of life color, analysis of memory color in the natural world, warm-cold/light-heavy/loud-quiet images and color taste, analysis of color association data by language, regional difference in colors which have been most enjoyed/regional difference in colors peculiar to cities, and analysis of regional difference in evaluation of coloring matching degrees. (NEDO)

  8. Research and development of a color-related global database of sensory values concerning color cognition, color emotions, etc. and the multimedia system to feedback it into products and living environment. FY 1995 data book 3 (1) 'Color cognition of the world's youth' analysis and mapping; 1995 nendo shikisai ninchi ya shikisai kanjo nado, shikisai ni taisuru kannochi no kokusaiteki database no kochiku to, sore wo seihin oyobi seikatsu kankyo no shikisai sekkei ni han'eisaseru multimedia system no kenkyu kaihatsu. Shiryoshu dai 3 kan (1) 'sekai no seinen no shikisai ninchi chosa' bunseki kekka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    An investigational study was conducted for the youth of main 20 cities of the world including Japan, aiming at clarifying characteristics of the color sense and at constructing a color-related global database and studying how to use it. This data is the results of the analyses. In the analysis of all items, the following were indicated: color mapping by country, analysis of similarity of countries, relations between 'the survey of the world's youth' and the internet survey, etc. In the analysis of each item, the following were shown: regional difference in color of hair/color of pupil/color taste, analysis of life color, analysis of memory color in the natural world, warm-cold/light-heavy/loud-quiet images and color taste, analysis of color association data by language, regional difference in colors which have been most enjoyed/regional difference in colors peculiar to cities, and analysis of regional difference in evaluation of coloring matching degrees. (NEDO)

  9. Increased dialogue between NADOs and academics – challenges and possibilities

    DEFF Research Database (Denmark)

    Gleaves, John; Christiansen, Ask Vest

    2015-01-01

    More than just repositories of knowledge, academics have an obligation to also forge new paths of discovery. As the boundary between what we know and what we still do not know expands, academics are not required to ask “what applied value does this discovery have.” Galileo’s curiosity in the time...... it took a chandelier to swing, measured only by his heartbeat, was not intended to help create modern timepieces, though it did through the discovery of the tautochrone nature of a pendulum. It was simple curiosity driven by unanswered questions and the human desire to know. We should pursue truth...

  10. Vallo Reimaa : "Statussu regionalnogo tsentra nado sootvetstvovat i za nego nado borotsja" / Vallo Reimaa ; interv. Aleksei Starkov

    Index Scriptorium Estoniae

    Reimaa, Vallo

    2007-01-01

    Regionaalminister vastab küsimustele, mis puudutavad Jõhvi gümnaasiumi juurdeehituse rajamist ja riigilt selleks toetuse taotlemist, linnade konkurentsi regionaalkeskuse staatuse saamiseks, Ida-Viru maavanema kandidaate. Minister on seisukohal, et tuleb toetada kõike, mis tugevdab Jõhvi kui regionaalkeskuse staatust, ja regionaalne gümnaasium on just selline objekt

  11. Flow characteristics of Hijiori HDR reservoir form circulation test in 1995; Koon tantai Hijiori jikkenjo ni okeru shinbu choryuso yobi junkan shiken (1995 nendo) kekka to ryudo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Fukushima, N; Hyodo, M; Shinohara, N; Takasugi, S [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan)

    1996-05-01

    This paper reports the result of a preliminary circulation test conducted in fiscal 1995 on a deep reservoir (at a depth of about 2200 m) in the Hijiori hot dry rock experimental field. One water injection well and two production wells were drilled to constitute a circulation loop, to which the circulation test was performed to investigate the flow characteristics thereof. The result revealed the following matters: total amount of injected water of 51500 m{sup 3} resulted in a total fluid recovery rate of about 40%; as a result of well stimulation given twice during the initial stage of the water injection, the continuity impedance in the vicinity of the injection well decreased largely (however, the continuity improvement upon the second attempt was considerably inferior to that from the first attempt); and increase in the water injection amount does not necessarily lead to increase in the production amount. The paper describes additionally that it is extremely difficult to interpret non-linearity between the injection and production amounts by using a model prepared previously with a main objective to analyze the Hijiori HDR circulation system. 1 ref., 9 figs., 1 tab.

  12. A influência de palmares e parachute na coordenação dos nados

    OpenAIRE

    Thiago Telles

    2012-01-01

    Resumo: A natação é uma modalidade esportiva que, ao longo dos anos, sofreu modificações, atingindo um alto nível de exigência, o que é refletido nas sessões de treinamentos e nas pesquisas sobre a modalidade. Sendo assim, para otimizar o deslocamento nos nadadores pode-se otimizar a força propulsora. Para isso, pode-se utilizar palmares e parachute. Os palmares tem como função promover o aumento artificial da área da mão, desta maneira, aumenta-se a área frontal da mão do sujeito em contato ...

  13. Vladimir Panov : obvinenija nado dokazõvat / Vladimir Panov ; interv. Jana Toom

    Index Scriptorium Estoniae

    Panov, Vladimir, 1941-

    2008-01-01

    Pistisevõtmises süüdistatud Tallinna endine abilinnapea Vladimir Panov vastab küsimustele, mis puudutavad viieaastast kohtuprotsessi ning Äripäeva ja meedia suhtumist talle esitatud süüdistusse. Kommenteerivad: Tarmu Tammerk, Andrus Saar, Edgar Savisaar

  14. "Estoniju v JeS zashtshishtshat ne nado!" / Signe Ratso ; interv. Eteri Kekelidze

    Index Scriptorium Estoniae

    Ratso, Signe, 1960-

    2004-01-01

    Majandus- ja kommunikatsiooniministeeriumi asekantsleri Signe Ratso sõnul ei too Eesti liitumine Euroopa Liiduga mingeid ootamatusi, Eesti ja EL muutuvad üheks majandusruumiks koos sellest tulenevate tagajärgedega. Tabel: Import kolmandatest riikidest 2003. a. 11 kuu jooksul

  15. 77 FR 42465 - Special Local Regulations, Cruce a Nado Internacional, Ponce Harbor; Ponce, PR

    Science.gov (United States)

    2012-07-19

    ... effect on the human environment. This proposed rule involves special local regulations issued in.... Dated: June 7, 2012. D.W. Pearson, Captain, U.S. Coast Guard, Captain of the Port San Juan. [FR Doc...

  16. Fjodor Berman : "Nado umet terjat dengi" / Fjodor Berman ; interv. Liana Turpakova

    Index Scriptorium Estoniae

    Berman, Fjodor, 1951-

    2006-01-01

    BLRT Grupp ühendab 61 firmat kuues riigis, aktsionärid on aastate jooksul kogu teenitud raha suunanud kontserni arengusse. BLRT Grupi arengust, probleemidest kvalifitseeritud tööjõuga, majandus- ja kommunikatsiooniministeeriumi suhtumisest. Juhatuse esimehe Fjodor Bermani karjäärist Eestis, puhkusest ja vaba aja veetmisest, perekonnast

  17. Samozvantsev nam ne nado, komandirom budu ja / Maksim Shmeljov, Aleksandr Tshaplõgin, Leivi Sher

    Index Scriptorium Estoniae

    Shmeljov, Maksim

    2007-01-01

    Kas Konstitutsioonipartei nimekirjas parlamendivalimistel kandideeriv Dmitri Linter ja tema kaaslased võivad kasutada liikumise Notshnoi dozor brändi ND omakasupüüdlikel eesmärkidel, küsivad autorid

  18. Report on achievements in fiscal 1975 in Sunshine Project. Studies on wide area existence of geothermal resources in great depth; 1975 nendo koiki shinbu chinetsu shigen fuson ni kansuru kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-03-01

    This paper reports the achievements in the following study items: (1) studies on the AFMT method, (2) observation of heat dissipation by using infrared thermal images, (3) evaluation on the annular topographic pattern in the Hachimantai area identified from the Landsat satellite images, (4) studies on the Tamagawa welded pyroclastic rocks, (5) studies on minerals transformed from the Tamagawa welded pyroclastic rocks, and (6) a method to analyze ground temperature data by using graphic display. Items 2 and 6 in the studies are on the heat balance method, and Item 3 is on remote sensing. Items 4 and 5 were performed as the study on geologic thermometry. In Item 1, a prototype AFMT method exploration device was fabricated, and field experiments were performed in the Onuma area in the Hachimantai wide-area geothermal experiment field. The experiment placed importance on finding problems in transmission and reception of signals from an artificially fluctuating magnetic field, whose result was found greatly contributive to understanding the physical phenomena. However, it was not possible to reach a level to analyze geological structures from the data. In Item 2, simple meteorological observation was performed on ground surface temperature distribution by using an infrared radiation thermometer of remote sensing type. Development was made on a method to measure natural heat dissipation amount from heat balance on the ground surface. (NEDO)

  19. Study on deep crustal resistivity structure using wideband magnetotellurics. In the case of eastern part of Hokkaido, Japan; Kotaiiki MT ho wo mochiita shinbu chikakuhi teiko kozo no kenkyu. Hokkaido Tobu chiiki ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Sato, H; Tanimoto, K; Maeda, T; Nishida, Y [Hokkaido University, Sapporo (Japan); Takada, M; Tamura, M [Hokkaido University, Sapporo (Japan). Research Center of Earthquake Prediction; Ogawa, Y [Geological Survey of Japan, Tsukuba (Japan); Nagao, T [Tokai Univ., Tokyo (Japan)

    1997-10-22

    Wide-range MT (magnetotelluric) observation is conducted to collect knowledge of the middle and lower parts of the crust of the above-named region, about which but a little information is available, for comparison with information about Kurile islands arc tectonics. Three traverse lines crossing the Kurile islands roughly in the north-south direction and two lines running from east to west are used, with the observation stations totalling 48. The distance between observation stations is 7-8km on the Nijibetsu line, and approximately 15km on the Nakashibetsu and Akan lines. A very wide frequency range of 320-0.0005Hz is used for measuring, and these results in detection with success of resistivity structure details from shallow to deep layers in the crust. The collected data are analyzed, and it is estimated that the northern and central parts have a high-low-high three-layer structure while the southern part has a low-high two-layer structure. Since the data obtained at observation stations at the middle of the lines, in particular, have an extremely low apparent value of several ohm/m at about 1Kz in the absence of splits in the TM (transverse magnetic) and TE (transverse electric) modes, it is inferred that the low-resistivity layer is considerably thick and is distributed rather uniformly. 13 refs., 5 figs.

  20. Experiment for deep seismic reflections in Hidaka, Hokkaido. Comparison between Vibroseis and explosive data; Hidaka chiiki ni okeru shinbu hanno data no shutoku jikken. Vibroseis to dynamite no hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, N; Ikawa, T [Japex Jeoscience Institute, Tokyo (Japan); Ito, T; Tsumura, N; Shinohara, M; Ikawa, T. Ikawa, H.; Asano, Y; Tanaka, Y; Miyazono, N [Chiba University, Chiba (Japan); Arita, K; Moriya, T; Otsuka, K; Omura, T [Hokkaido University, Sapporo (Japan); Kimura, M [Osaka Prefectural University, Osaka (Japan); Hirata, N [The University of Tokyo, Tokyo (Japan); Okuike, S

    1997-05-27

    This is a prompt report. These days the importance of acquiring knowledge about the structure from the lower crust down to the upper mantle is often discussed with reference taken to Hyogo-ken Nanbu Earthquake. The Hidaka collision belt where the lower crust is exposed on the surface is a rare phenomenon in the world and has been the subject of seismic survey. As a part of the survey, experiments are conducted by the use of vibrations produced by Vibroseis and dynamite sources. Every one of the shot records (20-second record) from the two types of vibration sources contains a clear echo in the vicinity of 16 seconds supposedly from a level deeper than 40 kilometers, not to mention reflections from shallow levels. Although some studies have to be conducted before the reflecting geological boundary (possibly the upper mantle) of the echo near the 16-second point can be identified, yet this is probably the reflection from the deepest level ever obtained in the seismic reflection survey conducted in Japan`s land area. It is proved by this experiment that vibration from a vibrator can reach as far as that from explosion if the vibrator specifications are rightly chosen. 4 refs., 3 figs.

  1. Report on the results of the Sunshine Project - Verification survey for geothermal exploration technology, etc. Summary. Survey of deep geothermal resource; Chinetsu tansa gijutsu tou kensho chosa. Shinbu chinetsu shigen chosa sokatsu seika hokokusho (Yoyaku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    As to the development of deep geothermal resource which is expected to contribute to increasing the capacity of future power generation in Japan, investigational study was made from FY 1992 to FY 2000, and the results were summed up. The investigational study was conducted for the hydrothermal convection type deep geothermal resource with a thermal conducting heating mechanism, of which Kakkonda is typical, including the drilling of deep exploration well using the existing technology. As a result, new information/knowledge were acquired about the thermal structure, reservoir structure and hydrothermal supply structure of the depths, and a deep geothermal model was made. Based on the model, a detailed simulation was made possible, and a whole image of the hydrothermal convection type deep geothermal resource with the thermal conducting heating mechanism was made clear. In the surface survey, observation of microearthquakes, high-accuracy MT method, etc. were carried out, and a grasp of the shape of a new granite body from the surface was made possible. Concerning the drilling technology, the geologic stratum with a temperature over 500 degrees C was successfully drilled down to a depth of 3,729m by prolonging the life of bit at the time of drilling by introducing the top drive system, the closed mud cooling device, etc. (NEDO)

  2. FY 2000 survey on technical trends. Survey of technical trends on materials for heightening of performance for power generation facility use; 2000 nendo gijutsu doko nado chosa. Hatsuden shisetsuyo koseinoka zairyo ni kakawaru gijutsu doko nado chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to high performance/high function plastic materials used in power generation facilities, technical trends were surveyed on the recycle situation and recycle R and D to study the subjects to be solved. For wire covering materials, vinyl chloride, polyethylene, rubber, etc. are used, and the recycle of resin has not been advanced. Concerning the generation of waste plastic, the existence of a lot of plastics different in characteristics makes the recycle difficult. As to the use of waste plastic as resource, the material recycle and recovery of combustion energy are being made, but only a part of the plastic is reused as chemical raw materials. Relating to the R and D of the chemical recycle technology, there are sample studies on the pyrolysis of polyolefine, dechlorination of chlorine base resins, etc. Recently, the following have been made public: proposal of depolymerization monomer based on the cyclic monomer, study of liquefaction of approximately 100% of the thermosetting resin, approach to the solvolysis by supercritical solvent. (NEDO)

  3. FY 1999 report on the study of the future course, etc. of 'the basic survey for promotion of Joint Implementation, etc.'; 1999 nendo 'kyodo jisshi nado suishin kiso chosa' no kongo no hokosei nado ni kansuru kento chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper conducted the demonstration of the multiplier effect of 'the model project for heightening of the international energy consumption efficiency, etc.' carried out by NEDO and its subsidiary project, 'the project on the basic survey for promotion of Joint Implementation (JI),' and the comparative study between these projects and the JI/CDM projects proposed in the world. In the quantitative evaluation of the multiplier effect, in the case of making the demonstration of the same technology in the same area both in the model project and the basic survey for promotion of JI, it becomes possible to grasp the CO2 reduction effect with high accuracy, but the CO2 reducible amount is small. Inversely, as to the technology for which the basic survey for promotion of JI is studied, but the model project is not carried out, it becomes possible to grasp the CO2 reduction effect with low accuracy, the CO2 reducible amount is large. In the comparison with the JI/CDM projects proposed in the world, the CO2 reduction amount was approximately $2.7 billion, 250 million tons, in the UNFCCC project, and approximately $5.0 billion, 500 million tons, in the IJ project. There was no very big difference in the cost effect. (NEDO)

  4. Basic tests of a rotation seismograph; Kaiten jishinkei no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Matsubayashi, H; Kawamura, S; Watanabe, F; Hirai, Y; Kasahara, K [Nippon Geophysical Prospecting Co. Ltd., Tokyo (Japan)

    1996-05-01

    For the purpose of developing a rotational seismograph capable of measuring the rotational component of seismic waves, vibratory gyroscopes were installed in the ground for the measurement of vibration of the ground, and the measurements were compared with the values obtained from tests using conventional velocity type seismographs. In the experiment, the plank was hammered on the east side and west side. The seismographs were arranged in two ways: one wherein they were installed at 7 spots at intervals of 1m toward the south beginning at a position 3m south of the vibration source with their rotation axes oriented vertical, with velocity type seismographs provided at the same spots; and the other wherein three rotational seismographs were installed 3m south of the vibration source with their rotation axes respectively oriented vertical, in the direction of N-S, and in the direction of E-W, with a velocity type seismograph provided at the same spot. It was found as the result that the rotational seismograph has a flat band on the lower frequency side and that it may be applied to elastic wave observation across a wide band. Accordingly, it is expected that it will be applied to exploration that uses the SH wave, to structural assessment that uses the Love wave, and to collecting knowledge about the features of natural earthquakes. 2 refs., 8 figs.

  5. Development of aluminium pleasure boats; Arumisei pleasure boat no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tsuzuki, A. [Toyota Motor Corp., Aichi (Japan)

    1999-10-01

    In February 1997, Toyota entered the marine business, a new business sector for it, by marketing a 28-foot cabin cruiser PONAM-28, developed by utilizing its automotive technologies. When Toyota began studying the possibility of entering the marine vessel industry in 1990, its main focus was on the environment. Therefore, in terms of materials procurement for the designs, Toyota refrained from using thermosetting resins, as much as possible. Instead, the decision was made to use an easily recyclable aluminum alloy for the hull which amounts to one-fourth of the vessel's total weight. (author)

  6. Development of artificial soft rock. Jinko nangan zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kishi, K.; Nishioka, T. (The Tokyo Electric Power Co. Inc., Tokyo (Japan)); Nojiri, Y.; Kurihara, H.; Fukazawa, E. (Kajima Corp., Tokyo (Japan))

    1990-09-15

    When a part of the ground is replaced with artificial materials in the construction of important structures on soft rock foundations, it is desirable for the artificial materials to have the rigidity equivalent to that of the surrounding ground and to be stable in the long term. The article reports a success in the development and utilization of artificial soft rocks satisfying the above conditions by using a raw material produced locally at the construction site. The soft rock aimed at was mudstone belonging to the Neocene period, and the artificial material of soil-mortal system is selected as the equivalent having the same physical properties. Improvements in selection of solidification agents and cohesive soil were especially contrived: taht is, a new material for solidification was developed by mixing blast-furnace cement and gypsum; and the mudstone on the site was used as the cohesive soil by slurrying it to adjust its grain size to homogeneous composition. The artificial soft rock resulting from the above contrivance showed excellent flow, self-leveling, and filling properties at the stage of fresh mortar, and the physical properties after hardning was very similar to those of the natural ground. The long-term stability was also confirmed by the tests on hydration reaction and environmental factors. 2 figs., 1 tab.

  7. Development of field navigation system; Field navigation system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ibara, S; Minode, M; Nishioka, K [Daihatsu Motor Co. Ltd., Osaka (Japan)

    1995-04-20

    This paper describes the following matters on a field navigation system developed for the purpose of covering a field of several kilometer square. This system consists of a center system and a vehicle system, and the center system comprises a map information computer and a communication data controlling computer; since the accuracy for a vehicle position detected by a GPS is not sufficient, an attempt of increasing the accuracy of vehicle position detection is made by means of a hybrid system; the hybrid system uses a satellite navigation method of differential system in which the error components in the GPS are transmitted from the center, and also uses a self-contained navigation method which performs an auxiliary function when the accuracy in the GPS has dropped; corrected GPS values, emergency messages to all of the vehicles and data of each vehicle position are communicated by wireless transmission in two ways between the center and vehicles; and accommodation of the map data adopted a system that can respond quickly to any change in roads and facilities. 3 refs., 13 figs., 1 tab.

  8. Development of new catalytic materials; Shinshokubai zairyo no kaihatsu doko

    Energy Technology Data Exchange (ETDEWEB)

    Tatsumi, Takashi [Yokohama National Univ., Kanagawa (Japan)

    1999-04-05

    The catalyst fulfils large role for the solution of environmental problem, resources problem, and energy problem. It is popular to carry out the research, which intends to realize the new process of which the environmental loading is low by the new catalyst. And, the development of catalyst material, which demonstrates the function under the ultimate condition like the environmental catalyst, is required. The interest has leaned in also using the solid catalyst for the synthesis of fine chemical such as intermediate and perfume of the medical supply synthesis. In this paper, the following are described as a new catalyst material: Zeolite and development trend of meso porous molecular sieve explosively studied recently. The application to the reaction is also simply touched. (NEDO)

  9. Development of mechanical brake assist; Mechanical brake assist no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Konishi, M; Shingyoji, S; Nakamura, I; Tagawa, T; Saito, Y; Ishihara, T; Kobayashi, S; Yoshida, M [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    We have recognized that there are drivers who cannot apply strong brake pedal force , in spite of the necessity of hard braking in emergencies. We have developed a `mechanical brake assist system` which assists drivers appropriately, according to the drivers` characteristics based on studying the characteristic`s of conditions of drivers applying the brake pedal force in emergency conditions. 2 refs., 7 figs., 1 tab.

  10. Developments of space station; Uchu station no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hashimoto, H. [National Space Development Agency of Japan, Tokyo (Japan)

    1996-03-05

    This paper introduces the Japanese experiment module (JEM) in developing a space station. The JEM consists of systems of a pressurizing section, an exposure section, a pressurizing portion of a supply section, a manipulator and an exposure portion of the supply section. The pressurizing section circulates and controls air so that crews can perform experiments under pressurized environment. The exposure section is a part in which experiments are carried out under exposure environment. The supply section runs between a station and the ground, with required devices loaded on it. The manipulator performs attaching a payload for the exposure section and replaces experimental samples. The JEM undergoes a schedule of fabricating an engineering model, testing for a certification a prototype flight model, and putting the model on a flight. The pressurizing section, exposure section and manipulator are at the stage of system tests. Surveillance of the JEM and control of the experiments are carried out at the Tsukuba Space Center. The Center is composed of a space experiment building, a zero-gravity environment testing building, an astronaut training building, a space station operating building, and a space station testing building. 7 figs., 2 tabs.

  11. Report on the present situation of the FY 1998 technical literature database; 1998 nendo gijutsu bunken database nado genjo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    To study database which contributes to the future scientific technology information distribution, survey/analysis were conducted of the present status of the service supply side. In the survey on the database trend, the trend of relations between DB producers and distributors was investigated. As a result, there were seen the increase in DB producers, expansion of internet/distribution/service, etc., and there were no changes in the U.S.-centered structure. Further, it was recognized that the DB service in the internet age now faces the time of change as seen in existing producers' response to internet, on-line service of primary information source, creation of new on-line service, etc. By the internet impact, the following are predicted for the future DB service: slump of producers without strong points and gateway type distributors, appearance of new types of DB service, etc. (NEDO)

  12. Efeitos antidepressivos da duloxetina e da fluoxetina no teste do nado forçado em ratos

    OpenAIRE

    Ciulla, Leandro; Menezes, Honório Sampaio; Bueno, Bárbara Beatriz Moreira; Schuh, Alexandre; Alves, Rafael José Vargas; Abegg, Milena Pacheco

    2007-01-01

    PURPOSE: To compare the effects of the antidepressant drugs duloxetine and fluoxetine on depressive behaviors in rodents. METHODS: Eighteen male Wistar rats were given systemic injections of duloxetine, fluoxetine, or saline prior to a Forced Swimming Test (FST). Immobility and number of stops were measured. RESULTS: Rats given injections of fluoxetine displayed significantly less immobility (p = 0.02) and fewer stops than the control group (p = 0.003). Duloxetine significanlty reduced the nu...

  13. Report on the present situation of the FY 1998 technical literature database; 1998 nendo gijutsu bunken database nado genjo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    To study database which contributes to the future scientific technology information distribution, survey/analysis were conducted of the present status of the service supply side. In the survey on the database trend, the trend of relations between DB producers and distributors was investigated. As a result, there were seen the increase in DB producers, expansion of internet/distribution/service, etc., and there were no changes in the U.S.-centered structure. Further, it was recognized that the DB service in the internet age now faces the time of change as seen in existing producers' response to internet, on-line service of primary information source, creation of new on-line service, etc. By the internet impact, the following are predicted for the future DB service: slump of producers without strong points and gateway type distributors, appearance of new types of DB service, etc. (NEDO)

  14. 78 FR 28167 - Special Local Regulation, Cruce a Nado Internacional de la Bahia de Ponce Puerto Rico, Bahia de...

    Science.gov (United States)

    2013-05-14

    ... individually or cumulatively have a significant effect on the human environment. This proposed rule involves..., 2013. D.W. Pearson, Captain, U.S. Coast Guard, Captain of the Port San Juan. [FR Doc. 2013-11360 Filed...

  15. El proceso del parpadeo ocular como indicador de emoción en la prueba de nado forzado

    Directory of Open Access Journals (Sweden)

    Samuel Bautista Peña

    2012-11-01

    Full Text Available The relaxed posture of the eyelids keeps the eyes closed, the eyes open is part of the active behavior in living organisms, the activity gives rise to the blinking eye, that for the majority goes unnoticed. You can classify several types of eyeblink, blinking is a response that participates in the facial expression of the emotions. The muscle of the eyelid is essentially involved in emotional responses, as shown during the surprise, fear, or startle. We have studied the eyeblinking linked to aversive events of short duration. We need to know what is happening with the blinking eye to aversive stimuli with longer duration. The forced swimming test (PNF, stimulation provides a sharp, intense and prolonged by 15 minutes. Then we assess the response of eye blinking under the effect of the aversive stimulation provided by the PNF. We used 10 type Wistar male rats experimentally naive, with a weight next to the 300 g were housed with boxes-individual room and free access to food and water. The response of blinking eye was defined as: the behavior of closing and opening in a short period that the eyelids cover the eyes of the rat. We used a modified procedure of the PNF in establishing as a criterion of time 15 minutes for each of the two trials. The first assay began to put the rat in the cylinder with water. The second assay was performed 24 hours after the first assay. The sessions were videotaped, of which the recordings were obtained. The graph shows us a process of change in the blinkin eye, this suggests to us that this is a eyeblinking emotional, which passes through: the surprise; anxiety; and something like depression. It is a complex of processes in which they are involved a variety of mechanisms. We compare our results with other researches of blinking. The descriptors process involved in the anxiety-depression, are at different levels and can go from its link with physiological states until the mechanisms at the biochemical level responsible for that behavior.

  16. Production of ethanol, fat and oil and methane gas from several crops. Sushu sakumotsu nado no energygen toshite no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Uehara, Tsuyoshi; Suganuma, Hirotoshi

    1988-05-01

    Aiming at production of ethanol, fat and oil and so on, ten kinds of miscellaneous cereal crops such as pearl-millet, soybean and so on were grown, and comparative investigation of the production rate which was considered utilization of whole plants were carried out. The suitability of vegetable wastes as methane fermentation materials for the methane gas production was investigated by the constituent analyses and methane fermentation experiments. Nine kinds of the grasses and vegetable wastes such as tomatoe buds, broccoli leaves were used for the investigation. As the results, the estimated yield of ethanol per 10 are from pearl-millet was 690 liter, the estimated yield of fat and oil per 10 are was 70 liter from soybean, The results of the analyses of nine kinds of the farm residues were as follows: (1) carbon content of about 40 %, (2) C/N ratio of 13 av., (3) C/P ratio of 91 av., and (4) the content of C,N and P was roughly appropriate. 680 to 760 milliliter of methane gas was produced from one gram of the dry matter of tomatoe bods, and in case of broccoli leaves, 424 milliliter of methane gas was produced, it was found that these values were not inferior to animal dung. (4 figs, 15 tabs, 6 refs)

  17. Report on evaluation/selection surveys on coal species, processes and others; Tanshu process nado hyoka sentei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This program analyzes the applicable coal species centered by Australia's Victoria brown coal and Chinese coal, which are promising alternative fuel sources for Japan for their reserves, prices, availability, suitability for liquefaction, etc, in order to clarify the possible problems, and commercialize the liquefaction techniques in the early stage. This report consists of 6 chapters. Chapter 1 describes development situations of brown coal, specifically for Australia's Victoria brown coal and Chinese coal. Chapter 2 describes characteristics of the reactions involved in the brown coal liquefaction. Chapter 3 describes current status of various liquefaction processes (solvolysis, solvent extraction, direct hydrogenation and C-SRC) under development in Japan, and problems involved in their future developments. Chapter 4 describes current status of the elementary techniques, e.g., those for slurry pretreatment (e.g., dehydration and crushing), solid/liquid separation, secondary hydrogenation, product upgrading and gasification. Chapter 5 describes the related techniques, and Chapter 6 discusses the demonstration survey results of de-ashing, primary/secondary hydrogenation, and dehydration of brown coal. (NEDO)

  18. Report on evaluation/selection surveys on coal species, processes and others; Tanshu process nado hyoka sentei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This program analyzes the applicable coal species centered by Australia's Victoria brown coal and Chinese coal, which are promising alternative fuel sources for Japan for their reserves, prices, availability, suitability for liquefaction, etc, in order to clarify the possible problems, and commercialize the liquefaction techniques in the early stage. This report consists of 6 chapters. Chapter 1 describes development situations of brown coal, specifically for Australia's Victoria brown coal and Chinese coal. Chapter 2 describes characteristics of the reactions involved in the brown coal liquefaction. Chapter 3 describes current status of various liquefaction processes (solvolysis, solvent extraction, direct hydrogenation and C-SRC) under development in Japan, and problems involved in their future developments. Chapter 4 describes current status of the elementary techniques, e.g., those for slurry pretreatment (e.g., dehydration and crushing), solid/liquid separation, secondary hydrogenation, product upgrading and gasification. Chapter 5 describes the related techniques, and Chapter 6 discusses the demonstration survey results of de-ashing, primary/secondary hydrogenation, and dehydration of brown coal. (NEDO)

  19. Avaliação da resposta imune humoral e análise comportamental de ratos Wistar submetidos a natação forçada e tratados com fluoxetina

    OpenAIRE

    Eduardo Vignoto Fernandes

    2012-01-01

    A fluoxetina é amplamente utilizada para tratamento de transtornos comportamentais. O teste do nado forçado é um modelo experimental de estudo da depressão em ratos, no qual drogas antidepressivas revertem o comportamento passivo de flutuação em repetidas imersões em água. O objetivo deste estudo foi verificar os efeitos da fluoxetina no comportamento do teste do nado forçado e sobre a imunidade. Primeiramente, foi investigado o efeito do teste de nado forçado em relação ao tratamento com flu...

  20. FY 1999 report on the survey of the basic cooperation project of enhancement of the international energy consumption efficiency. Project on promotion of exchanges with the persons concerned with government agencies, etc.; 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo, kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo chosa hokokusho. Seifu kikan nado kankeisha koryu sokushin jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of promoting the understanding of effective energy utilization and constructing corporative relations between countries, the persons concerned with government agencies of India, China, Indonesia, Vietnam, Myanmar and Thailand were invited to Japan, and exchanges of opinions were made on policies, technical development, the state of the introduction, etc. The persons concerned with governments of India, China and Indonesia participate in NEDO Forum 2001 to give lectures on the energy policy of their own. The persons sent from the Vietnamese government paid visits for survey to NEDO, Obayashi Corp., Kawasaki Heavy Industries, Ltd., Mitsubishi Materials Corp. and Taiheiyo Cement Corp. as reference of the model project on cement sintering plant power reduction. The persons sent from the Myanmar government paid visits for survey to NEDO, ECCJ, Chiyoda Corp., Yokogawa Electric Corp. and Cosmo Oil Co. as reference of the model project on energy conservation at fertilizer plant. The persons concerned with the Thai government paid visits for survey to the plants concerned with the model project on residue combustion waste heat recovery facilities at paper mills and the model project on waste heat recovery at steel material heating furnace. (NEDO)

  1. Exploration for petroleum and natural gas in Sonai Plain

    Energy Technology Data Exchange (ETDEWEB)

    Konishi, K

    1965-09-01

    Exploration in the Sonai Plain by Sekyu Shigen Kaihatsu Kabushiki Kaisha (Oil Resources Development Corporation) since 1955 is described. The development tasks are made difficult due to the presence of permeability traps. However, 41 out of 65 wells drilled up to late March of 1965 have been successful. Quantities of crude oil and natural gas produced in 1963 were, respectively, 5 and 6 times those of 1958. The Sonai Plain is a relatively new area, and there are still many unknown factors, yet the rate of development has increased greatly. More and deeper wells are expected to be drilled with even better results.

  2. Current srate and problems in Japanese petroleum development. ; International trends in petroleum development and problems in Japanese devepment business. Waga kuni sekiyu kaihatsu no genjyo to mondai ten. ; Sekiyu kaihatsu no kokusai doko to waga kuni kaihatsu jigyo no kasai

    Energy Technology Data Exchange (ETDEWEB)

    1991-11-05

    Petroleum production and its supply and demand require ever closer coordinations among the countries involved. On the other hand, however, there a large number of difficult questions as the problems of global environmental pollution and greenhouse effects increase their seriousness and the economic resources in the petroleum business become scarcer. This paper describes the current state of the Japanese petroleum development, the necessity of spontaneous petroleum development, the international trends in the petroleum development business, and the tasks for Japan in the petroleum development business. Japan is a late comer in the petroleum development business. There are such difficulties as sizes of oil fields being discoverd are becoming smaller, the natural conditions in development target areas are getting severer, and the economic effects are inferior. Japan, whose petroleum self-supply rate is about 0.3%, whose petroleum dependency is heightening as a result of increase in nuclear power generation, and who is the third largest petroleum consuming country next to the U.S.A and Soviet, must use efficiently her financial and technical powers to vitalize her spontaneous petroleum development. Japan has a duty to contribute to the world {prime}s future stabilized supply of oil. The Japanese Government has launched the five-year fund development plan to perform basic surveys for ail in the north-east part of the Japan Sea and the pacific Ocean.

  3. Development in fiscal 1999 of technology to put photovoltaic power generation system into practical use. Management of research and development (System development committee working group); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri (system kaihatsu bukai)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    This paper reports activities carried out in fiscal 1999 by the system development committee working group, a subordinate organization of the committee for development of the photovoltaic power generation technology. The items of implementation laid with emphasis in the current fiscal year included deliberations on the research achievements of the projects completed in fiscal 1999, on the research achievements of the new projects during fiscal 1999, and on pre-final evaluation of the development of a technology to put photovoltaic power generation system into practical use. The themes on the progresses in fiscal 1999 reported in March 2000 consisted of the followings: research and development of a system evaluation technology, investigation and research on supply capability evaluation on the photovoltaic power generation system, researches on peripheral devices for AC modules, investigation and research on electric safety of the photovoltaic power generation system, investigation and research on long-term reliability of inverters, investigation and research on meteorological data for optimal design, investigation and research on evaluation of the photovoltaic power generation, research on a photovoltaic power generating multi-hybrid system, research on a high-density linkage technology, and demonstrative research on a solar beam micro-hydraulic hybrid system. (NEDO)

  4. Fiscal 1996 comprehensive report on R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu sokatsu hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    R and D was conducted on technology for composite thin film formation such as laser MOCVD, for thin film lamination, and for synthesis reaction and characterization in compounded fields where temperature/pressure/magnetic field/electrical field, etc., are compounded, for the purpose of creating materials with functions newly added or reinforced by regulating compositions and structures through atomic/molecular orders. The R and D was conducted on 24 themes, which were rearranged into four categories. Examples of the themes are as follows; development of super hard permanent magnets by crystallization process control of Nd-Fe-B amorphous alloys, as for structural control technology; research on high functional thin film sensors (PbLaTiO{sub 3}) using laser MOCVD, and research on ultra thin film by multi-ion-beam sputtering with ion/photo irradiation, as for thin film technology; R and D on highly ordered structure control technology in electrode surface compounded reaction fields, as for compounded fields; and, research on diagnostic technique for compounded reaction fields by laser-ionization method, as for supporting technologies. (NEDO)

  5. Overview of FY1997 human media technology R and D; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido Shin energy Sangyo Gijutsu sogo Kaihatsu Kiko itaku jigyo. Human media no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports a summary of results in fiscal 1997 of research and development of human media technology. Fiscal 1997 launched design and trial fabrication of the following items: interface to improve efficiency and safety of plant operators, accommodation of multimedia contents to aid Kansei design, city development design aiding technologies using contents retrieval and presentation technologies and virtual reality, and empirical evaluation technologies for safety, comfort and convenience. Specific study assignments were extracted on a virtual media technology, a Kansei media technology and a knowledge media technology being three elementary technologies for human media to make clear the research and development approaches to be taken in the coming fiscal years. In addition, a human media technology committee, a research and development working group, and an investigation working group were established. Also launched were investigations on research trends in the human media technology, and investigative researches on contacts of information needs in industries with human media. 59 refs., 114 figs., 24 tabs.

  6. Basic survey on the residence using hybrid energy in snowy cold regions; Sekisetsu kanreichi ni okeru hybrid energy katsuyogata jutaku nado ni kansuru kiso chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The conceptual model and feasibility of the hybrid energy system for residences and public facilities in snowy cold regions were studied. Based on the existing data, the existing and available amounts of natural energy and unused energy in the target area, Sapporo were estimated. Based on the predicted energy demands of 4 kinds of building models, the energy systems for such models were studied. The use of the following energies was considered: photovoltaic power generation and solar heat for all the models, household sewage energy for the multiple-dwelling house model, and wind power generation for the public facility model. The annual energy balance was calculated to evaluate it. The use of additional commercial electricity was necessary, while surplus solar heat energy was found in summer which can push up the self-sufficiency rates of the residence and public facility models to 70% and 44%, respectively. The multiple- dwelling house model which can use a large amount of household sewage energy could utilize 80% of new energy, while the other 3 models utilized only 60-70% of that. 81 figs., 42 tabs.

  7. Research report for fiscal 1998. Study of utilization of biomass including foods in energy industry; 1998 nendo shokubutsu nado no biomass no energy riyo ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Rice being produced as food is taken up out of various types of biomass, and a feasibility study from the viewpoints of technology and economy is conducted as to its use in the energy industry. The production of ethanol from rice, though it has no past record worth discussion, is similar to the production of ethanol from other biomass resources in terms of technology and economy. The problem is that the production cost of rice is far higher than those of other materials. It is expected, however, that there will a large-scale production cost reduction and an increase in the yield when novel cultivation techniques are introduced in the future. It is also expected that alcohol from rice will be sufficiently competitive with alcohol from molasses or the like when the exploitation of cellulose-family by-products such as husks becomes feasible. The study on this occasion deals solely with the effective use of farmland and the surplus rice. A confrontation between rice as a biomass resource and rice as a food has to be avoided as much as possible in the long term because it may cause a price rise and compromise the security of food supply. That is, in discussing this matter, it is mandatory to draw a very definite line between rice as a food and rice as an alcohol production material. (NEDO)

  8. Survey of the waste-fueled power generation introducing technology. Case study 1 (fiscal 1996); Haikibutsu hatsuden donyu gijutsu chosa nado. Case study no jisshi 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A case study on A city was conducted aiming at making a detailed manual for introducing the waste-fueled power generation. The study was made in terms of a large-capacity waste-fueled power plant, estimation of the waste amount considering wide-area processing, size of facilities, comparison of four types of combustion furnace, steam condition/seawater cooling/power generating efficiency, etc. As a result, the following were proposed: As to the size of facilities, a capacity as large as possible is recommended in the light of the scale merit of costs of the waste-fueled power plant and final disposal site and the environmental preservation. Concerning the high efficient power generation, recommended are 450degC and 60-80 ata which are steam conditions for coping with high temperature corrosion. In respect to seawater cooling, the adoption is recommended making good use of locational conditions since the output energy increases by approximately 16%. Any furnace types including the fluidized bed furnace are equal. The amount of dioxin becomes below 0.1ng/Nm{sup 3} because of the control of furnace combustion temperature, residence time, catalytic desulfurization facilities, blowing of activated coal into the flue, etc. 172 figs., 78 tabs.

  9. Fiscal 2000 survey report on regional new energy vision formulation for Kawanabe town, Kagoshima Prefecture; 2000 nendo Kawabecho chiiki shin energy vision sakutei nado chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A regional new energy vision has been formulated for Kawanabe town, Kagoshima Prefecture, to be participated in by inhabitants and beneficial to both natural environment protection and inhabitants. The results of the survey are described in six chapter which involve (1) the basic philosophy of vision formulation, (2) outline of new energy, (3) environmental characteristics and townspeople's awareness, (4) energy situation and the amount of new energy existing in Kawanabe town, (5) regional new energy vision for Kawanabe town region, and (6) future tasks. After a study of the existing amount of new energy, energy demand, and people's requests, it is concluded that photovoltaic power generation, wind power generation, hot spring heat utilization, small scale water energy, and refuse-derived energy be the types to be preferably introduced into the town. Projects are established and concrete plans are prepared thereunder, which concern the reinforcement of public relations and enlightening activities, installation of a wind power system as one of enlightening activities, study of Kawanabe town's own subsidy system for encouraging the introduction of photovoltaic power systems and solar heaters for domestic use, and the introduction of photovoltaic power systems into public facilities such as school houses. In conclusion, it is hoped that, since financial difficulties will be a strong factor to impede new energy introduction, the subsidy system will be a solid one. (NEDO)

  10. Fiscal 1999 survey report. Fiscal 1998 basic survey for promotion of joint implementation, etc. (Analysis of results); 1998 nendo kyodo jisshi nado suishin kiso chosa kekka no bunseki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The 40 'Surveys for promotion of joint implementation, etc.' conducted by NEDO (New Energy and Industrial Technology Development Organization) in fiscal 1998 aimed to pick out projects that would positively utilize the flexible measures (three Kyoto mechanisms) for the achievement of greenhouse gas reduction targets defined at COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change). In this paper, concerning these 40 surveys, studies are conducted for reaching conclusions about setting baselines for the future, execution of similar feasibility studies in the future, application of flexible measures, and opinions towards project implementation. The 40 surveys were, concretely speaking, conducted not to work out policies for actualization of given projects but to consider philosophies of project actualization and baseline formation for the future. In this paper, project outlines, environmental impact assessment, and economic assessment (investment assessment) are put in order for each of the surveys, and relations between amounts of global warming gas reduced and project costs, and project profitability, are analyzed for each of the surveys. (NEDO)

  11. Report on new energy vision establishment project in Higashi Naruse Village area; Higashinarusemura chiiki shin energy vision sakutei nado jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A new energy vision was established in the Higashi Naruse Village in Akita Prefecture. The population of the village is continuing the decreasing trend since 1950 to 3,390 persons as of 2000. The annual energy demand in this village is about 320,000 GJ, accounted for by the consumer department at about 40%, the transportation department at about 36% and the industrial department at about 24%. The carbon dioxide emission amount therefrom is estimated 6,300 t-C annually. The expected usable quantity of new energies in the village would be available, in the decreasing order, in the wind power as the most promising source, forestry bio-mass, snow cold heat energy, agricultural bio-mass, and solar beam (heat). The total quantity would be 514,330 GJ annually in heat utilization, and 85,305 MWh in electric power. The new energy introducing project includes introduction of photovoltaic and wind power generation into Kurikoma Mountain Villa, introduction of wind power generation into the Junes skiing area and Oyanagi Natural Park, introduction of photovoltaic power generation and heat utilization into primary and middle schools, introduction of clean energy fueled automobiles into the village office, and introduction of photovoltaic power generation into general houses. (NEDO)

  12. Report on evaluation/selection surveys on coal species, processes and others. Appendix; Tanshu process nado hyoka sentei chosa hokokusho. Furoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This report, consisting of 7 chapters, summarizes literature related to liquefaction of coal. Chapter 1 describes the results of the (Project Lignite), i.e., development of the concept of two-stage liquefaction of lignite. Chapter 2 describes the COSTEAM process, which uses synthesis gas (CO-H{sub 2}) as the reducing agent and coal moisture as the hydrogen source for liquefaction of coal of low degree of carbonization, e.g., brown coal. Chapter 3 describes solubilization of coal with alcohol, where coal is reacted with ethanol and NaOH at 300 to 420 degrees C. Chapter 4 describes liquefaction of coal and production of lighter products with tetrahydroquinoline as the hydrogen donor. Chapter 5 describes low-temperature carbonization as the process for liquefying coal, in particular brown coal. Chapter 6 describes possibility of development of new liquefaction techniques for brown coal, including solvolysis for liquefaction, role, recovery and reuse of catalysts, short contact time processes, and coal pretreatment. Chapter 7 describes economic viability of the secondary hydrogenation. (NEDO)

  13. Fiscal 2000 survey report on regional new energy vision formulation for Kito village; 2000 nendo Kitoson chiiki shin energy vision sakutei nado chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A regional new energy vision has been formulated for Kito village, Tokushima Prefecture, in the hope that it will trigger off an effort to build a mentally affluent community. Kito village is a 2,000-strong village situated in a mountainous region, and consumed 1.3 times 10{sup 5} GJ in energy in fiscal 1999. The results of activities conducted in this connection are summarized in four chapters which are (1) the outline of survey, (2) local characteristics, (3) existing amount of new energy, and (4) plans for promoting new energy introduction and energy conservation. Discussed as plans for promoting new energy introduction and energy conservation are a business of commercialization feasibility survey, plot to construct a natural energy operated school building, and a plan for promoting energy conservation. Discussed in relation to commercialization feasibility survey are a small scale hydroelectric power generation utilizing a sand-trap dam, small scale hydroelectric power generation utilizing waste water from a fish farm, regional heat supply business utilizing ligneous biomass, manufacture of ligneous pellet fuel, and so forth. In relation to the promotion of energy conservation, a drive will be launched to positively bring photovoltaic power generation into daily life. (NEDO)

  14. Research report for fiscal 1998. Promotion of activities implemented jointly etc. in China; 1998 nendo Chugoku ni okeru kyodo jisshi katsudo nado suishin chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The Kyoto Protocol allows some flexibility in the implementation of methods for achieving the goal, such as emission trading, activities implemented jointly (AIJ) among advanced countries, construction of clean development mechanisms (CDM) with developing countries, etc., and Japan intends to positively make use of them for the achievement of the goal. For China, who holds second place in the list of greenhouse gas emitting countries in the world, the promotion of CDM is quite important. With the situation taken into consideration, interaction was effected with Chinese officers and scientists of government agencies and academic institutes involved in environmental matters, and researches were conducted. Views and information were exchanged regarding environmental problems and, after on-site investigations, researches were conducted and suggestions were presented as to how AIJ and CDM should be. The suggestions covered Chinese policies toward AIJ and CDM, current state of AIJ projects in China and systems for their promotion, means for enhancing such projects, and discovery of candidates for AIJ and CDM project application. (NEDO)

  15. Fiscal 1998 joint promotion basic research report. Energy saving project for Achinsk refinery in Russia; 1998 nendo kyodo jisshi nado suishin kiso chosa. Roshia Achinsuku seiyujo shoene project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For prevention of global warming by greenhouse effect gas, study was made on energy saving measures for Achinsk refinery in Russia. Achinsk refinery is a relatively new plant put into operation in 1983, however, because of no various equipment for use combustion heat effectively, its average thermal efficiency is as low as 60%-70%, resulting in fuel consumption more than necessary one. Based on the study result, the following remodeling designs were made: Improvement of a heat exchange efficiency by relocation of heat exchangers to reduce fuel consumption of a heating furnace as much as possible, conversion of an existing heating furnace based on an old design concept to an advanced one, installation of a waste heat recovery system including a preheating convection unit and air preheater, reinforcement of heating furnace wall insulator, installation of an optimum control system for furnace operation, and improvement of a fuel supply system efficiency. This design showed possible reduction of heating furnace load, and possible furnace thermal efficiency of 90%. (NEDO)

  16. Survey on Pacific area energy policies by information collection. Laos and Myanmar; Taiheiyo energy seisaku joho nado genchi shushu chosa. Laos, Myanmar

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For planning the Pacific area energy policy of Japan, the field survey on energy situations was carried out in Laos and Myanmar. Since Laos is rich in hydraulic resources, the future electric power development is expected. Development of oil and coal resources is yet in a planning stage. Electricite du Laos (EdL) is in charge of electricity business, and its power generation capacity amounts to 220MW (including hydroelectric one of 93%), and a half of it is exported. Based on the predicted growth rate of 9%/y for domestic power demand, development of the capacity to 440MW by fiscal 2002 is scheduled. Myanmar has natural gas and various mineral resources, and is rich in hydroelectric resources. Myanmar Electric Power Enterprise (MEPE) is in charge of electricity business. The power generation capacity amounts to 1.34GW (including private one of 26%). The power generation facility is composed of gas turbine one of 53% and hydroelectric one of 33%. Based on the predicted growth rate of 11.5%/y for domestic power demand, development of the capacity to 1.6GW by 2001 is scheduled. For the present, conversion of previous gas-firing power plants to efficient combined cycle ones is a main issue. 21 figs., 43 tabs.

  17. Project report on drawing district energy-saving visions for Town of Nishi Senboku; Nishi Senboku machi sho energy vision sakutei nado jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Studied in this project are concrete energy-saving procedures, and potentially saved energy and abated CO2 emissions in Town of Nishi Senboku, to promote energy saving and abatement of gas emissions which cause global warming. The energy-saving procedures studied include co-generation, utilization of waste heat, wind power generation, utilization of low-temperature heat by snow, fuel-efficient vehicles, use of insulators for houses, energy-saving type electric appliances, energy-saving activities, and eco-driving. The results indicate that the energy-saving activities and eco-driving can potentially more contribute to energy saving than the others. The study on introduction of energy-saving facilities in the 'Nukumori Hot Spring/Umeria' project indicates that the heat pump plus co-generation case is the most advantageous, because it can potentially reduce primary energy by 2,845,215MJ/y and CO2 emissions by 22,688kg-C/y. Introduction of energy-saving facilities is also studied for an information center in the Nishi-Senboku service area for the Akita Highway. The results indicate that the introduction can potentially reduce primary energy and CO2 emissions by 25 and 13%, respectively. (NEDO)

  18. Fiscal 2000 survey report on regional new energy vision formulation for Oki town; 2000 nendo Okicho chiiki shin energy vision sakutei nado chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    Efforts are in progress to build a resource circulation type town symbiotic with natural environments at Oki town, Fukuoka Prefecture, which is an agricultural community where creeks run in every direction. A new energy vision has been worked out for the town, which centers about a plan for building a resource circulation type community. The survey results are summarized in six chapters dealing with (1) the survey outline, (2) local conditions relative to energy, (3) energy supply/demand structure, (4) amount of new energy in existence, (5) records and analysis of inhabitants' approach to energy conservation, and (6) a new energy introduction plan. The new energy introduction plan consists of four items involving a short term plan or a key project, a project for medium/long term surveys or feasibility study for the commercialization of new energy, plans for reducing energy consumption, and so forth. Discussed in relation to the short term plan are the introduction of photovoltaic power generation into public facilities, installation of a photovoltaic power station to be jointly utilized by the inhabitants, establishment of a grant system for the installation of solar water heaters for domestic use, creation of an additional subsidy system for domestic photovoltaic power generation, and the like. (NEDO)

  19. Fiscal 2000 report on regional new energy vision formulation project for Yunomae town, Kumamoto prefecture; 2000 nendo Yunomaecho chiiki shin energy vision sakutei nado jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A regional new energy vision has been formulated for Yunomae town, Kumamoto Prefecture, from the standpoint that local autonomies are required to work out measures compatible with Government energy policies and thereby to wrestle with environmental measures being undertaken across the world. The results of activities conducted for this purposed are stated in six chapters, which cover (1) the meaning of regional new energy vision formulation and its position, (2) outline of Yunomae town, (3) energy and environments, (4) energy situation in Yunomae town, (5) Yunomae town's regional new energy vision, and (6) plans for promoting the embodiment of the vision. In chapter (5), basic policies toward new energy utilization, overall plan, leading projects, and energy conservation measures are stated. The types of new energy taken up for discussion are photovoltaic power, wind power, biomass power, refuse-derived energy, and hydraulic energy. Projects are subjected to study, which relate to photovoltaic power generation, solar heat utilization, small scale hydroelectric power, small scale wind power, and the introduction of clean energy vehicles. It is expected that these projects when carried out will cover approximately 10% of the current energy consumption of the town. (NEDO)

  20. Driver`s behavior and the motion of motorized wheelchair when driving over rough surfaces; Dansa nado fuseichi sokoji no dendo kurumaisu no undo to join no kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Enomoto, A; Yokomori, M; Yamaguchi, S [Meijo University, Aichi (Japan)

    1997-10-01

    We analyzed about the motion of motorized wheelchairs and the driver`s behavior when passing over the small obstacles in place of the rough surface road or the gateway of house and road by experiment. The tested two type wheelchairs are the front wheel drive and the rear wheel drive. The lean angle of head and the pulse rate of driver, the feeling for stability and the yaw angle and the roll angle of the wheelchair bodies, and the deflection angle of front wheels of rear drive. 4 refs., 11 figs., 1 tab.

  1. FY 1997 report on the field survey on country situations including efficient energy consumption. Vietnam; 1997 nendo chosa hokokusho (energy shohi koritsuka nado chiiki josei genchi chosa). Vietnam

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Field survey was made on the current state of and issues on energy in Vietnam. In Vietnam, firewood is in wide use as non-commercial energy, and sums to a half of total energy consumption. Other energies such as hydroelectric power, petroleum, natural gas and coal are self-sustainable. Commercial energy consumption in 1995 is estimated at 10,070,000t in oil equivalent, which is broken down into 23% for coal, 42% in oil, 5% for natural gas and 30% for electricity. Abundant water resources will form the mainstay of future electric power supply. Commercial production of oil started in 1986 becoming an oil exporting country. Several promising natural gas fields were discovered as the result of the exploration by foreign capital. Coal deposits are estimated to be nearly 3.5 billion tons, and most of them are anthracite. Electric power demand is growing at a higher rate than the economic growth of Vietnam. The growth rate of electric power demand is set to be 1.3 times that of GDP. Since construction funds for new plants cannot be satisfied with the national budget and domestic investment alone, the country is expecting foreign capitals. 21 figs., 36 tabs.

  2. Report on `Survey of commercialization of intellectual ownership such as patent rights`; `Tokkyoken nado chiteki shoyuken no jitsuyoka ni kansuru chosa` hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A survey was conducted on research results in industrial circles, universities, etc. in the U.S., Europe and Japan, especially the state of how intellectual ownership such as patent rights is handled and the present situation of the commercialization of intellectual ownership, proposing problems and measures to be taken for promotion of practical use of excellent research results in Japan. The most important thing obtained from the survey is that study jointly by industrial circles and universities in the U.S. and Europe is much more advancing than that in Japan and is firmly established not only in industrial circles, universities and national research institutes, but in the whole society, actually producing a lot of favorable results. For Japan to catch up with the U.S. and Europe, needed is not only accumulation of the ideas in the past, but drastic measures to be taken from a new point of view. Concretely, it was proposed that by belonging intellectual properties such as patent rights to universities/research institutes and transferring their disposal rights to them, royalties of licenses are given back to inventors as incentives, and that as a body promoting the transfer to the industrial circle, `management organization` to which private vitality is introduced is established in universities/research institutes in order to promote interconnection between the industrial circle and universities. 15 refs., 35 figs., 36 tabs.

  3. FY1998 report on the research on support for practical recycling technologies. Part 1; 1998 nendo recyle gijutsu nado jitsuyoka shien kenkyu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project aims at development, demonstration and utilization of waste recycling technologies. This report summarizes the fiscal 1998 results. The test/demonstration plant for separation and removal of foreign materials was constructed for effective use of waste building wood, and its optimum operation condition was studied. Although some foreign materials exists, 90% of waste building wood chips were separated and recovered through some improvements for the plant. An advanced separation technology is expected. As for fibering technology, fibers with target compression strength were obtained from cedar chips through a disintegration experiment using a newly developed refiner plate. Although the compression strength of fibers obtained from waste building wood chips was slightly poor, it is attained by increasing the target specific gravity of light- weight wooden materials by nearly 10% from 0.1. As for fiber orientation technology, as the tension of a forming belt was adjusted to achieve sufficient width compression, nearly 90% of the target compression strength was attained. A width compression method remains to be solved. (NEDO)

  4. FY 2000 report on the survey of the stabilization of wind power generation power system, etc.; 2000 nendo furyoku hatsuden denryoku keito anteika nado chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of elucidating effects of output fluctuations at the time of quantity introduction of wind power generation, conducted were observation of wind characteristics in Hokkaido and analysis of the characteristics, estimation of fluctuations in wind power output, analysis of fluctuations in system frequency, etc. In the observation of wind characteristics, wind velocity/wind direction were measured at observation posts of 30 wind turbines installed at 16 sites in Hokkaido. Concerning the conversion into wind power output, 10 cases were selected such as the case of passage of low atmospheric pressure, etc., and the generator unit and wind firm were simulated in detail. In the estimation of wind power output, good agreement with the results estimated was confirmed at points very near to posts of observation of wind characteristics. As to the evaluation of effects of wind power generation to the system, power system frequencies were simulated using the models constructed and using capacity and kinds of frequency adjusted power source as parameter. As a result, it was indicated that there was a possibility of frequency's sharply fluctuating in case the surplus energy in frequency adjustment is reduced by fluctuations in demand and further in case wind power output is fluctuated. (NEDO)

  5. Fiscal 2000 report on regional new energy vision formulation project for Yoron town; 2000 nendo Yoroncho chiiki shin energy vision sakutei nado jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A regional new energy vision has been formulated for Yoron town, Kagoshima Prefecture, which will serve as guidelines for building an Environmentally Friendly Island. Yoron town is a town of approximately 6,000 inhabitants as of fiscal 2000, its energy consumption is equivalent to 61,427 drums in terms of crude oil, and it receives electric power from Yoron Power Plant of Kyushu Electric Power Co., Inc. The results of activities conducted in this connection are summarized in seven chapters, which are (1) coping with new energy vision formulation (2), energy supply and demand, (3) estimation of existing amount of new energy, (4) basic policy toward new energy introduction, (5) projects for introducing new energy, (6) existing energy systems, and (7) reference materials. Named as projects are the construction of a water supply power source (for storage pump) for the Furusato district; power source for farmland irrigation pumps; power sources for the integrated sports park and municipal library; power source for a farmyard compost center; wind power, photovoltaic power, and combined power generation facilities for streetlights; and the utilization of bagasse. (NEDO)

  6. Report for fiscal 2000 on establishment of new energy vision in Fujino Town; 2000 nendo Fujino chiiki shin energy vision sakutei nado hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to show specifically the efforts of working on new energies in Fujino Town in Kanagawa Prefecture, the existence quantity of new energies centering on the sun and woods was made clear to discuss the possibilities of utilizing them. Furthermore, investigations were performed on the energy demand and supply structure and possibilities of introducing new energies, and the specific new energy introduction plan was established. The activity achievements were put into order by the following six items: 1) the basic conception of the new energy vision, 2) various conditions of Fujino Town related to new energies, 3) energy demand and supply structure, 4) utilizable quantity of new energies, 5) toward the introduction of new energies, and 6) specific new energy facilities to discuss the introduction. Item 6 includes facilities to be built by defining model areas, facilities to discuss the full-swing introduction into facilities managed by the township, facilities to be discussed of full-swing introduction and to be composed in relation with the overall plan including large size hot water supply devices used at the spa, firewood boilers, a heat recovery system, and a large-scale photovoltaic power generation system. (NEDO)

  7. Report on regional new energy vision formulation project for Kahoku town, Kumamoto Prefecture; Kahokucho chiiki shin energy vision sakutei nado jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A regional new energy vision has been formulated for Kahoku town, Kumamoto Prefecture, for the realization of an energy resource circulation type regional community in which people earnestly strive to be symbiotic with nature. The results of related activities are shown in six chapters, which are (1) the prerequisites to the plan, (2) outline of the Kahoku town region, (3) surveys of the existing amount and expectedly available amount of new energy, (4) feasibility of new energy introduction, (5) assessment of new energy introduction plans and their effect, and (6) tasks to discharge, and policies to follow, for new energy introduction. In chapter (5), new energy introduction plans and introduction policies are shown. Plans are made for the incorporation of photovoltaic power facilities, small hydroelectric power facilities, and bamboo chip boilers into public facilities; the installation of 750 kW class wind power facilities; and the adoption of hybrid vehicles to serve as official special vehicles. It is expected that these plans when implemented will bring about a 1,400 t-c/year reduction in CO2 emissions. As for the introduction of wind power generation, the dimensions are determined by taking into consideration the prerequisites to a NEDO (New Energy and Industrial Technology Development Organization) grant. (NEDO)

  8. Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

  9. Research and development of photovoltaic power system. Research on low temperature deposition of polycrystalline thin films; Taiyoko hatsuden system no kenkyu kaihatsu. Teion seimaku gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sato, K [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan). Faculty of Technology

    1994-12-01

    This paper reports the result obtained during fiscal 1994 on research on a technology of low temperature deposition of polycrystalline thin films for solar cells. This research used ITO coated glass substrates, on which CdS was accumulated to a thickness of about 100 nm by using the CBD process, and over this deposition a CuInSe2 film was formed at 300{degree}C by using the ion cluster beam (ICB) process. The manufactured solar cells with a glass/ITO/CdS/CuInSe2/Au structure had an efficiency of 2%. In manufacturing a CuGaSe2 thin film by using the ICB process, effects of acceleration voltage relative to cluster beams and ionization current were investigated. It was found that the film morphology, the result of analysis by using X-ray diffraction, and the electric conductivity are sensitive to the ionization current. From these findings, an optimum film forming condition was derived. A CuGaSe2 thin film was manufactured by using the ICB process over a Cds thin film deposited by using the CDB process. Both of the surface morphology and X-ray diffraction patterns of the film did not show a large change, indicating a possibility of manufacturing cells with a reverse structure. Effects of heat treatment on CuInSe2 monocrystals were evaluated by using ESR and FTIR. 6 figs., 1 tab.

  10. Development of large scale wind energy conservation system. Development of large scale wind energy conversion system; Ogata furyoku hatsuden system no kaihatsu. Ogata furyoku hatsuden system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for development of large scale wind energy conversion system. The study on technological development of key components evaluates performance of, and confirms reliability and applicability of, hydraulic systems centered by those equipped with variable pitch mechanisms and electrohydraulic servo valves that control them. The study on blade conducts fatigue and crack-propagation tests, which show that the blades developed have high strength. The study on speed-increasing gear conducts load tests, confirming the effects of reducing vibration and noise by modification of the gear teeth. The study on NACELLE cover conducts vibration tests to confirm its vibration characteristics, and analyzes three-dimensional vibration by the finite element method. Some components for a 500kW commercial wind mill are fabricated, including rotor heads, variable pitch mechanisms, speed-increasing gears, YAW systems, and hydraulic control systems. The others fabricated include a remote supervisory control system for maintenance, system to integrate the wind mill into a power system, and electrical control devices in which site conditions, such as atmospheric temperature and lightening, are taken into consideration.

  11. Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

  12. Development of small-size transmission tower erection method; Kogata tetto kumitate koho no kaihatsu kenkyu (gaibushiki crane ni yoru kogata tetto kumitate koho no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Matsuishi, S.; Asano, J.; Koji, Y. [Kansai Electric Power Co. Inc., Osaka (Japan); Tsujimura, I.; Teramoto, A. [The Kanden Kogyo Incorporated, Osaka (Japan); Sasaki, T.; Mito, K. [AG Ajikawa Corp., Osaka (Japan); Tsuji, M.; Fukumoto, T.; Yamaguchi, N.

    1997-09-30

    To reduce the construction period and cost and to enhance the safety during 77 kV-class transmission tower election, a new method of small steel transmission tower erection using an external type crane has been developed. For the selection of cranes, a commercially available self-climbing crane was employed which has an operating radius of 11 m, a lifting load capacity of 1.5 t, and a lift of up to 60 m. For the space analysis using a model tower, various supporting methods with horizontal supporting members, stress analysis for each tower stub, and apparatuses were examined. For the demonstration tests of election using the model tower, strain gages were attached at each point of steel tower, crane and horizontal supporting members, to measure the stress of members at each stage of the election. It was confirmed that there were no problems. For the election of actual steel tower, the practicality of this method was compared with that of conventional methods. The construction period was reduced in 20%, and the cost was reduced in 4%. The safety of this method was drastically enhanced due to the lack of moving on the tower and less manual operation. 9 figs., 1 tab.

  13. Fiscal 1992 report on geothermal development promotion survey (Development of geothermal reservoir assessment technique); 1989 nendo chinetsu kaihatsu sokushin chosa (Chinetsu choryusou hyoka shuho kaihatsu hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Efforts were exerted in fiscal 1984-1992 to develop techniques for appropriately assessing a geothermal reservoir for its productivity for duly predicting the optimum scale of power generation to be provided thereby. In the development of simulators, geothermal reservoir simulators (SING-1, -2, -3) and a geothermal well 2-phase flow simulator (WENG) were developed. As for the treatment of fractures in a reservoir and of substances soluble in the hot water, the methods for dealing with them were improved and augmented. In a model field study in a Hokkaido forest, reservoir pressure continuous observation and monitoring, temperature logging and pressure logging for existing wells, and geothermal fluid chemical analysis were performed for reservoir analysis, in which both natural state simulation and history mapping excellently reproduced the temperature and pressure distributions. The temperature and pressure distributions in a natural state simulation, out of the results of an analysis of the Oguni district model field, Kumamoto Prefecture, agreed not only with those in the natural state but also with the pressure transition data in the observation well. (NEDO)

  14. FY1997 geothermal development promotion survey. Development feasibility study 'Ashiro area'; 1997 nendo chinetsu kaihatsu sokushin chosa. Kaihatsu kanosei chosa (Ashiro chiiki) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-01

    With regard to the Ashiro Town area in Iwate Prefecture, this paper reports the result of evaluations based on temperature and pressure logging after a lapse of an extended period of time (well No.2) and a steam jet test (well No.1). These activities were performed as the survey on promotion of geothermal development and survey on development feasibility in fiscal 1997. As a result of the overall analysis based on the present survey and ones in the past, the geothermal system model in the surveyed area may be conceived as follows: in both of the N7-AR-1 and N7-AR-2 wells drilled in the southern part of the surveyed area, temperature as high as 250 degrees C or higher was confirmed; the underground temperature is 200 degrees C or higher at an altitude level of zero meter and 250 degrees C at around -500 m, leading to a belief that the high temperature area spreads to south; as a fracture system holding geothermal fluid, a fault was identified at the N7-AR-1 well drilling depth of 1710 m; in the steam jet test, a geothermal reservoir (a shallow geothermal reservoir) was confirmed to exist; the geothermal fluid that has jetted out shows alkaline Na-SO{sub 4} type; and the deep geothermal reservoir has high temperature and is presumed to be in the two-phase condition, presenting promising factors as the geothermal resources. (NEDO)

  15. FY 1998 annual report on the project of basic survey for improving energy consumption efficiency in developing countries and programs of international conferences including IPCC. Report on CDM workshop; Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo / IPCC nado kokusai kaigi jigyo (CDM workshop hokokusho) 1998 nendo jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    It is decided in the COP4 that the concrete schemes for the (Kyoto Mechanism) should be boiled down towards the end of 2000. Of the many outstanding issues concerned, those related to the clean development mechanism (CDM) involve a number of problems awaiting solution. In particular, setting the baselines for amounts of the greenhouse effect gas emissions in projects not existing, which are essential for identifying reduced amounts of emissions (or credits), poses serious difficulty because of wide arbitrariness involved in the methodology. Therefore, (standardization) of the procedures is demanded for the accurate identification. In actuality, however, no methodology has been established as to what methods will be possibly applicable to widely diversified types of projects. This workshop, therefore, has focused the discussions on the (baseline problems), expecting to serve as a trigger for the future directions by presenting international researches and promoting the discussions thereon to deepen recognition of these problems, where the AIJ experiences have served as one of the bases. (NEDO)

  16. Report on achievement in the preceding research related to global industry technologies for the global industry technology research and development project. Research on gas systems substituting global warming gases such as PFC used in manufacturing semiconductors; 1998 nendo chikyu kankyo sangyo gijutsu ni kakawaru sendo kenkyu. Handotai seizo nado ni shiyosuru PFC nado no chikyu ondanka gas no daitai gas system no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The present semiconductor manufacturing process uses a great amount of PFC having large global warming coefficients and extremely long atmospheric life. A research was made particularly on reduction of its emission from etching processes. After introducing how the semiconductor industry has been working conventionally on protection of the global environment, this paper makes clear the purpose and positioning of this preceding research, as well as how it is moved forward. The paper also reports the results of analyzing and discussing the exhaust gases from etching devices using several kinds of substitute PFC gases. Survey results are reported on the possibilities of new substitute gases, plasma decomposition and treatment of exhaust gases, reaction process simulation, and in-situ analyzing and evaluating technologies. Investigations were made on the possibility of using no PFC in wiring processes which consume greater amount of PFC, as well as on wiring techniques using inter-layer insulation film with low dielectric rate, a new wiring structure forming technology, new functional elements, circuits and systems in a wide range. Proposals were given on specific research and development themes and plans that begin in fiscal 1999. (NEDO)

  17. FY 1999 report on the study of the future course, etc. of 'the basic survey for promotion of Joint Implementation, etc.'; 1999 nendo 'kyodo jisshi nado suishin kiso chosa' no kongo no hokosei nado ni kansuru kento chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper conducted the demonstration of the multiplier effect of 'the model project for heightening of the international energy consumption efficiency, etc.' carried out by NEDO and its subsidiary project, 'the project on the basic survey for promotion of Joint Implementation (JI),' and the comparative study between these projects and the JI/CDM projects proposed in the world. In the quantitative evaluation of the multiplier effect, in the case of making the demonstration of the same technology in the same area both in the model project and the basic survey for promotion of JI, it becomes possible to grasp the CO2 reduction effect with high accuracy, but the CO2 reducible amount is small. Inversely, as to the technology for which the basic survey for promotion of JI is studied, but the model project is not carried out, it becomes possible to grasp the CO2 reduction effect with low accuracy, the CO2 reducible amount is large. In the comparison with the JI/CDM projects proposed in the world, the CO2 reduction amount was approximately $2.7 billion, 250 million tons, in the UNFCCC project, and approximately $5.0 billion, 500 million tons, in the IJ project. There was no very big difference in the cost effect. (NEDO)

  18. FY 2000 International energy use rationalization project. International technology dissemination project for improving energy consumption efficiency (Green helmet project for steel heating furnaces in Thailand); 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Kokusai energy shohi koritsuka nado gijutsu fukyu jigyo (Green helmet jigyo (Tai: kozai kanetsuro))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The project for energy saving dissemination activities and technological assistance for Thailand is carried out, and the FY 2000 results are reported. For Siam Iron and Steel (SISCO), the experts are dispatched for reviewing the operating conditions of the facilities constructed by the model project, their maintenance and examination, time series diagnosis of the recuperator performance, and providing technical assistance for fuel consumption and high-load combustion of the downstream unit. Furthermore, the site survey and technical assistance are provided for two newly selected Thai steel enterprises, Sahaviriya Steel Industries Public Co. (SSI) and the Bangkok Iron and Steel Works Co. (BISW). For SSI, it is predicted that energy of approximately 50Mcal/ton can be saved by, e.g., enhancement of waste heat recovery, enhancement of heat insulation of skid pipes, introduction of steel discharging temperature prediction system, and combustion control. For BISW, it is predicted that energy of approximately 25Mcal/ton can be saved by, e.g., enhancement of waste heat recovery and reduction of heat loss in the waste gas. (NEDO)

  19. Fiscal 2000 survey report on rationalization project for international energy conservation, technological dissemination project for international energy conservation, and Green Helmet Project. Japan-China alternative energy seminar/waste disposal; 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo, kokusai energy shohi koritsuka nado gijutsu fukyu jigyo, green helmet jigyo chosa hokokusho. Nicchu sekiyu daitai energy seminar haikibutsu shori

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper explains the Japan-China alternative energy seminar (February 28 and March 1, 2001, at Beijing). The purpose of the seminar is to introduce systematic and three-dimensional or land/sea/air measures for waste disposal including recycling in Japan, to provide guidance of measures in improving recognition and methods for waste disposal in China, and also to contribute to the dissemination and promotion of a model project for effectively utilizing waste heat from rubbish incineration, a project being implemented in Harbin City now. The activities of NEDO were introduced, with emphasis placed on a model program, called Green Aid Project, for managing heat from waste incineration. On the subjects of sustainable development, urban environment, and energy, the policy of China's tenth five-year plan was demonstrated, and the treatment of wastes in China was also explained. The present state of waste processing in Japan was introduced, as was its maintenance of the facilities. Concerning Japan's waste processing technologies and characteristics of the equipment, there were presented non-incineration processing including crushing/separating, RDF, compost, methane fermentation, etc.; incineration plants; and each of the technologies such as combustion, exhaust gas, ash treatment, use of remaining heat, and gasification melting. (NEDO)

  20. Fiscal 2000 report on cooperative basic project on international energy consumption improvement/International conference project such as IPCC. International Symposium on the Kyoto Mechanisms; 2000 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / IPCC nado kokusai kaigi jigyo Kyoto mechanism ni kansuru symposium hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    The above-named symposium was held at United Nations University in the period April 12-13, 2001, and the conference is outlined in this report. The symposium aimed to contribute to the progress of international rule making and to the enhancement of mutual understanding through the exchange of views and opinions by negotiators representing their countries over the Kyoto mechanisms, the rule of emissions trading in particular, and through the analysis of negotiators' options; to discuss how international rules should be from a practical viewpoint with the participation of people related to the market or industries and engaged actively in the implementation of the mechanisms; to enrich Japanese people's knowledge about the mechanisms and to enhance their understanding of greenhouse gas emissions reduction techniques making use of the mechanism of the market; and so forth. The conference included Session 1: Current status of international negotiations and views from parties, Session 2: Toward credible and workable scheme of the mechanisms (Parts 1 and 2), and Session 3: Emissions trading - Outstanding issues and options. (NEDO)

  1. FY 1999 survey report on the survey of destruction technology of HFC, etc. for rationalization of energy use. Survey of the actual state of use/recovery/emissions of HFC, etc.; 1999 nendo energy shiyo gorika HFC nado hakai shori gijutsu chosa hokokusho. HFC nado shiyo kaishu haishutsu jittai chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This survey was aimed at collecting the basic data for studying a possibility of conversion of the recovery system of refrigerant freons, mostly DFC, into HFC, etc., which has been proceeded with in Japan. Of HFCs, PFCs and SF{sub 6} used for survey, only SF{sub 6} is now being recovered and processed. As to HFCs, HFC-134a was arranged, and the recovery/destruction to meet users' handling methods are requested because of the diverse usage and users. The points of the control of emissions of chemical substances into the atmosphere are the decrease in number of times of transport/filling-up at the time of materials handling and the closed system in plants and installation. If considering the heightening of efficiency of materials flow, requested are the decrease in number of times of transport/filling-up, the increase in quantity received by users, and measures to be taken for leakage at the time of receiving. In relation to the conversion of the recovery system of refrigerant freons, mainly CFC, into HFC, etc., all the industries concerned with the generation of the used substances to the materials flow have to promote the technical development for the structure and recovery in cooperation with each other. (NEDO)

  2. Fiscal 2000 report on cooperative basic project on international energy consumption improvement/International conference project such as IPCC. International Symposium on the Kyoto Mechanisms; 2000 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / IPCC nado kokusai kaigi jigyo Kyoto mechanism ni kansuru symposium hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    The above-named symposium was held at United Nations University in the period April 12-13, 2001, and the conference is outlined in this report. The symposium aimed to contribute to the progress of international rule making and to the enhancement of mutual understanding through the exchange of views and opinions by negotiators representing their countries over the Kyoto mechanisms, the rule of emissions trading in particular, and through the analysis of negotiators' options; to discuss how international rules should be from a practical viewpoint with the participation of people related to the market or industries and engaged actively in the implementation of the mechanisms; to enrich Japanese people's knowledge about the mechanisms and to enhance their understanding of greenhouse gas emissions reduction techniques making use of the mechanism of the market; and so forth. The conference included Session 1: Current status of international negotiations and views from parties, Session 2: Toward credible and workable scheme of the mechanisms (Parts 1 and 2), and Session 3: Emissions trading - Outstanding issues and options. (NEDO)

  3. Fiscal 1999 technical survey report. Basic project on international cooperation on energy consumption improvement, etc. (Japan International Cooperation Center project on promotion of exchange of specialists); 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo chosa hokokusho. Kokusai kyoryoku center jigyo suishin senmonka koryu sokushin jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    Specialist related to the governments of Thailand, Malaysia, and Indonesia where NEDO (New Energy and Industrial Technology Development Organization) implements its model projects were invited. They exchanged opinions with officials of the Japanese Government and affiliated organizations over measures for effective energy utilization. Opinions were also exchanged over the response of energy-consuming industries, development of technologies, and the status of their adoption. Activities of government-related participants are described below. Under a Model Project for Utilization of Waste Heat from Incineration of Industrial Waste at Industrial Estate, five Thai people with Industrial Estate of Thailand visited Ministry of International Trade and Industry, NEDO, NKK Corporation, Toyota Motor Corporation, and Keiyo Food Industrial Park. Under a model project on the recovery of waste heat from paper sludge incineration, four Malaysian people with Ministry of Energy, Communications and Multimedia or with Energy Center visited Ministry of International Trade and Industry, NEDO, NKK Corporation, Toyota Motor Corporation, and Japan Paperboard Industries Co., Ltd. Under a model project on the utilization of paper sludge and solid waste, four Indonesian people with Ministry of Industry and Trade or with Ministry of Mines and Energy visited Ministry of International Trade and Industry, NEDO, Babcock-Hitachi K.K., and Oji Paper Co., Ltd. (NEDO)

  4. Report for fiscal 1999 on the international and fundamental cooperation project for energy consumption efficiency improvement and the international conference project such as IPCC. The meetings of IPCC specialists and IPCC symposiums; 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / IPCC nado kokusai kaigi jigyo. IPCC senmonka kaigo oyobi IPCC symposium hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-10-01

    This paper reports the meetings of specialists and the symposiums by the inter-governmental panels for climate change (IPCC) in fiscal 1999. Three working groups were established for evaluation on climate change from scientific aspects, evaluation on effects and countermeasures from socio-economic aspects, and evaluation on mitigation measures from socio-economic aspects. The working groups have started preparing the third evaluation reports. Common problems are handled in a unified framework as the traversable problems. Specialist meetings are held for several important themes. Especially for the cost problems, preparation of a guidance paper has started, that include the costs and benefits by territories and departments. The themes for the specialist meetings include: cost problems related to effects and countermeasures for climate change and mitigation measures; the IPCC activities for the cost evaluation in the past and an outline of the traversable problems; problems in effects, applicable measures, and mitigation measures; and unification of the cost evaluations. The themes for the symposiums are the frontier line of the climate change problems, and include the outline of IPCC, the current status and issues in the working groups and the special reports for each group. (NEDO)

  5. FY 2000 report on the basic survey to promote Joint Implementation, etc. Prevention of emissions of gasoline vapor from oil depots in Indonesia; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Indonesia sekiyu kichi nado kara no gasoline joki hoshutsu no boshi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A field survey was conducted of oil shipment depots in Java and Bali islands owned by Indonesia's state-run oil company to study measures for reduction in greenhouse effect gas emissions. Studies were made on the grasp of the amount of the hydrocarbon vapor emitted into the air, the amount of the gasoline recovered in case of adopting the vapor emission preventive technology, equipment cost/operational cost, etc. Concretely, the following three were studied: change of the gasoline storage tank to the inner floating roof type, and prevention of evaporation loss at the time of receiving and breathing loss caused by temperature changes; replacement with the vapor recovery type loading arm to recover gasoline vapor generated at the time of shipment/filling, and installation of the vapor recovery unit to recover vapor as gasoline; vapor balance system to recover in underground tank the gasoline vapor generated at the time of filling gasoline at gas station. As a result of the study, the recovered gasoline amount was 66,393 Kl/y and the CO2 reduction amount was 14,474 t/y at oil shipment depots and approximately 650 gasoline stations in Jakarta and Surabaya. (NEDO)

  6. FY 1999 report on the results of the investigation of feasibility of joint implementation promotion through plant-related technology transfer to Central/Eastern European countries; 1999 nendo Chu Too nado chiiki ni okeru plant yushutsugata gijutsu iten wo tsujita kyodo jisshi nado suishin kanosei ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Feasibility of joint implementation promotion through plant-related technology transfer is investigated for 15 Central and Eastern European countries. Emissions of the greenhouse effect gases can be relatively easily abated in these countries by improving energy utilization efficiency, because they have more advanced infrastructures than developing countries, and are behind the developed countries in modernization of the facilities. Therefore, European and North American countries have been positively promoting the AIJ programs in these countries, and there are fierce competitions for promising projects. It will be necessary for Japan to provide public loans, e.g., environmental yen loans, to promote the plant-related JI/CDM projects in these countries. Many of these countries have not drawn plans for reducing emissions of the greenhouse effect gases, and expect establishment of the international cooperation systems for exchanging information related to global warming problems, and introducing the Japanese technologies and policies. (NEDO)

  7. Project for rationalization measures for international energy conservation. Model project concerning efficient consumption of energy for international energy conservation (Model project of waste heat recovery on billet reheating furnace); 1999 nendo kokusai energy shiyo gorika nado taisaku jigyo seika hokokusho. Kokusai energy shohi koritsuka nado model jigyo (kozai kanetsuro hainetsu kaishu model jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of curtailing energy consumption in the steel industry, a heavy energy consuming industry in Thailand, a model project was carried out for waste heat recovery on a billet reheating furnace, with the fiscal 1999 results compiled. This model project is to install a high efficiency recuperator and the latest combustion control system in the existing furnace in a SISCO (The Siam Iron and Steel Co., Ltd.) plant in Thailand. This year, following the preceding year, the construction manual was prepared, as were the test run manual, performance verification manual, operation and maintenance manual, etc. Supervisors were also dispatched to the site, giving guidance of the installation work, test run and the demonstrative operation, on the basis of these documents. Operation for verifying performance of the equipment was implemented on November 17, 1999, with the intended results obtained. Subsequently, operation maintenance instructors were dispatched, with energy saving effect proved through the collection/analysis of operation data and monitoring, for example. Further, as the dissemination activities, pamphlets and videos were prepared, and seminars were held, among others. (NEDO)

  8. Feasibility study of Copahue geothermal development project, Argentina; Aruzenchin kyowakoku Copahue chiiki no chinetsu kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    Abe, M.; Yamada, M.; Nakanishi, S.; Todaka, N. [Electric Power Development Co. Ltd., Tokyo (Japan); Fujita, T.

    1996-03-15

    Geothermal resources have been evaluated in the Copahue district. For this survey administrated by JICA, drilling of a deep test well with a small bore (COP-3) and blowout tests were conducted. This district is located at the east side of the Andes elongated in the N-S direction. Volcanoes with similar active periods and active states are distributed in the N-S direction, which forms a divide with the Pacific Ocean side. The Copahue-Caviahue composite volcano in the surveyed area is located nearly in the central part of the volcanic zone, which forms a special ring topography. Geology of the Copahue district consists of volcanic effusive rocks during the Tertiary and Quaternary periods. There are five prospecting fields with geothermal indications in the surveyed area. From the survey, an area of about 13 km{sup 2} was evaluated as a geothermal resource field. Especially, in the area of about 4 km{sup 2} including COP-1, 2 and 3 wells, the steam predominant type reservoirs were found out. As a result of estimation of the geothermal resource potential by the volumetric method, a highly prospective power generation potential of 30 MW was evaluated in the field where the steam predominant type reservoirs were confirmed by the boring wells. 7 refs., 13 figs., 1 tab.

  9. Development of measurement apparatus for high resolution electrical surveys; Komitsudo denki tansa sokuteiki no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Moriuchi, H; Matsuda, Y; Shiokawa, Y [Sumiko Consultants Co. Ltd., Tokyo (Japan); Uchino, Y [Cosmic Co. Ltd., Tokyo (Japan)

    1996-05-01

    For the enforcement of the {rho}a-{rho}u survey method which is a type of high-density electrical survey, a multichannel resistivity measuring instrument has been developed. This instrument, in addition to the above, conducts resistivity tomography and various other kinds of high-density electrical survey. A potential produced by a low frequency rectangular current of 1Hz or lower outputted by the transmitter of this instrument is received and measured by the receiver connected to electrodes positioned at 100 or less locations. The receiver comprises a scanner that automatically switches from electrode to electrode, conditioner that processes signals, and controller. A transmitter of the standard design outputs a maximum voltage of 800V and maximum current of 2A, making a device suitable for probing 50 to several 100m-deep levels. The receiver is operated by a personal computer that the controller is provided with. The newly-developed apparatus succeeded in presenting high-precision images of the result of a {rho}a-{rho}u analysis for an apparent resistivity section and of the underground structure, verifying the high quality of the data collected by this apparatus. 10 refs., 5 figs., 1 tab.

  10. Development of S-wave portable vibrator; S ha potable vibrator shingen no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kaida, Y; Matsubara, Y [OYO Corp., Tokyo (Japan); Nijhof, V; Brouwer, J

    1996-05-01

    An S-wave portable vibrator to serve as a seismic source has been developed for the purpose of applying the shallow-layer reflection method to the study of the soil ground. The author, et al., who previously developed a P-wave portable vibrator has now developed an S-wave version, considering the advantage of the S-wave over the P-wave in that, for example, the S-wave velocity may be directly compared with the N-value representing ground strength and that the S-wave travels more slowly than the P-wave through sticky soil promising a higher-resolution exploration. The experimentally constructed S-wave vibrator consists of a conventional P-wave vibrator and an L-type wooden base plate combined therewith. Serving as the monitor for vibration is a conventional accelerometer without any modification. The applicability test was carried out at a location where a plank hammering test was once conducted for reflection aided exploration, and the result was compared with that of the plank hammering test. As the result, it was found that after some preliminary treatment the results of the two tests were roughly the same but that both reflected waves were a little sharper in the S-wave vibrator test than in the plank hammering test. 4 refs., 9 figs., 1 tab.

  11. Development of new-concept superconducting power equipment; Shinkino chodendo denryoku kiki no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hamajima, T.; Tsurunaga, K.; Urata, M. [Toshiba Corp., Tokyo (Japan)

    1998-01-01

    The superconducting magnet energy storage (SMES) system has a function by which magnetic energy is stored in a superconducting coil without loss and discharged very rapidly into the power line when needed. The fault current limiter has a function by which transport current is passed without impedance and excessive fault current is restricted by generating large impedance in an emergency. These are the functions of new power equipment, which can not be realized by the conventional equipment. In the small-scale SMES project, Toshiba has fabricated 100 kWh-class element coils and 1 kWh/1 MW modules as the first step of practical application for power system control. For the superconducting fault current limiter, Toshiba has developed a 6.6 kV-1 kA class fault current limiter without supplying cooling medium such as helium, and limiting tests of fault current have been successfully conducted. Through the long-term tests of element coils for SMES and the system interconnection tests of module-type SMES, it is expected that the technological development for practical application is accelerated. 4 refs., 7 figs., 3 tabs.

  12. Development of a water hydraulic servovalve; Suiatsu servo ben no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Urata, E.; Nakao, Y. [Kanagawa University, Kanagawa (Japan). Faculty of Engineering; Yamashina, C.; Miyagawa, S.; Usami, Y.; Shinoda, M. [Ebara Research Co. Ltd., Kanagawa (Japan)

    1997-06-25

    An electrohydraulic servovalve that uses clear water as a pressure medium (water hydraulic servovalve) is developed. A conventional electrohydraulic servovalve cannot work with this hostile fluid. This paper explains the structure and functions of components, and the relationship between them, as well as development procedure of the water hydraulic servovalve. The basic idea for the development is to support the spool of the valve with hydrostatic bearings and to lead the water from the bearings to the flapper-nozzle system, which, in this valve contains a laminar restriction upstream from the nozzle instead of the turbulent restriction in the conventional flapper-nozzle system. This paper also explains the design procedure of the hydrostatic bearing in the valve and the connection of electromagnetic elements and the fluidic elements. The manufactured water hydraulic servovalves show good characteristics in their smooth motion, endurance and controllability, including dynamic characteristics. 25 refs., 12 figs.

  13. Development and utilization of liquid quartz light modulating film. Ekisho choko film no kaihatsu to riyo

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, M. (Ajinomoto Co. Inc., Tokyo (Japan))

    1992-03-01

    This paper introduces the polymer dispersed liquid crystal (PDLC) ACT'' sheet, a liquid quartz light modulating film, developed by the Ajinomoto Company in Japan. A mixture of liquid crystal and polymer precursor is sandwiched between polyethylene terephthalate films imparted with transparency conductor made of indium tin oxide (ITO), which is then polymerized by heating or irradiating ultraviolet rays to obtain a PDLC. The film has a thickness as thin as about 0.3 mm, and good processibility. The sheet uses light modulating elements functioning on scatter and permeation of light. Clarification was made on the voltage dependence of cloudiness, total light permeability, straight and parallel light permeability, the response, and the operating voltage. The system consumes small amount of power with a threshold value of about 35V, and is suitable to operate large areas when working on the utility power supply. An incident light having a high diffusion capability when the electric field is turned off exhibits a high clouding function. The system gives an excellent feel of colorlessness and transparency when the electric field is turned on. The performances in heat insulation, infrared reflection capability and noise resistance are expected to be compounded for a functional versatility. 4 refs., 6 figs., 2 tabs.

  14. How to proceed R and D effectively; Gijutsu kaihatsu no koritsutekina susumekata

    Energy Technology Data Exchange (ETDEWEB)

    Kawakita, Tetsuya [Ajinomoto Corp., Tokyo (Japan)

    1999-07-05

    They greatly divide R and D into next three in the enterprise, it is considered. (1) The goal-oriented basic research. (2) The applied research. (3) Technology development. Here, they try to want to consider the measure for efficient result sending out in technology development. It always considers that the largest effect is raised in research personnel who was limited in advancing technology development, it is observed in the standpoint for the operation management. The thought of Concurrent Engineering has already been taken in daily management, and it is had thing sure. In large wave of the internationalization, the high competition superiority is ensured in respect of the cost competitiveness, while the goal is clarified, and while it lectures on the means for overcoming the bottleneck. Responding to the expectation of the management by the further improvement in the technology development force believes not differing role of the engineer in the enterprise. (NEDO)

  15. Research and development project plans for FY 1995; 1995 nendo kenkyu kaihatsu jigyo keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-04-01

    The present research and development project plans for FY 1995 administrated by NEDO consist of research and development of new energy, and research and development of industrial technology. Are illustrated further enhancement of new energy introduction promotion measures, new stage of international projects, promotion of new energy and new energy technology development, further enhancement of industrial and scientific technology research and development, integrated measures against global and urban environment problems, and budget of NEDO projects in FY 1995. The research and development of new energy includes coal conversion technology, solar energy technology, geothermal energy technology, energy conversion and storage technology, hydrogen, alcohol and biomass energy technology, geothermal energy resources, coal resources development, new energy promotion department activities, NEDO information center activities, and so on. On the other hand, the research and development of industrial technology includes research and development of industrial technology, and global environment technology. The research and development of industrial technology consists of superconductivity, new materials, biotechnology, electronics, information and communications, machinery and aerospace, natural resources, humanity, life and society, and various leading researches.

  16. R and D of remote reading system. Remote reading system no kaihatsu kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nakano, H.; Hamada, T.; Nakamura, O. (The Kansai Electric Power Co. Inc., Osaka (Japan)); Imai, Y.; Akiyama, K.

    1992-03-25

    As measures for the spots difficult in metering within a framework to integrally automate the power distribution, a remote reading system was prototypically tested and evaluated in reliability on the actual field. The system methodically selected the signal {prime}s line injection, high frequency wave signal and voltage detection, while the signal frequency, transmission rate and highest transmission output were set at approx. 3.5KHz, 7.5bps and 50dBm, respectively from the test result. The demonstration test on reliability of the system locatively selected a vicinity of high voltage consumer, high harmonic wave-generating consumer, transforming station, etc. The total ratio of success in reception was comparatively high in Kuzuno and Yamazaki areas, but low in Kamojyo and Ichinomiya areas, The badness in reception was caused by the fluctuation in noise and strongness in damping which was influenced by the condenser in the high voltage consumer. The locative relation between the parent and child stations of system, and high voltage consumer being classified into four patters, an application table of remote reading system was prepared by simulation. 14 figs., 6 tabs.

  17. Development of sound absorption measuring system with acoustic chamber; Kogata kyuon koka sokutei sochi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takahira, M.; Noba, M. [Toyota Motor Corp., Aichi (Japan); Matsuoka, H. [Nippon Soken, Inc., Tokyo (Japan)

    1998-05-01

    In order to measure sound absorption performance necessary to develop sound absorption materials, development was made on a device consisting of a small sound box capable of measurement inexpensively and easily, as a measure against the reverberation chamber method. In order to obtain stabilized diffusion sound internally, the sound box has a shape of asymmetric seven-side body in which sides do not face squarely with each other. The box was so sized that a large number of resonant vibration postures can be constituted at the targeted frequency simultaneously in the box. The box has a commercially available cone speaker with good acoustic output characteristics in frequency range of higher than 500 Hz installed on an inner side of the box. The sound source uses a method to derive sound absorption rate from difference of sound pressure levels. In order to eliminate need of averaging treatment by using a multi-point measurement inside the box, a discussion was given to provide an opening on part of the box to place the sound receiving point outside the opening. A square test piece is placed on the floor 0.5 meter or more away from the speaker in the box. As a result of the experiment, it was verified that the sound absorption rate obtained by this device corresponds well with that by the reverberation chamber method. The size of the test piece was also found adequate. 2 refs., 11 figs., 1 tab.

  18. Research report of FY 1997 on the industrial science and technology development. Technology development of super-metal (technology development of nano-amorphous structural control materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (nano-amorphous kozo seigyo zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development of the innovative metals have been conducted, by which the weight reduction of members can be done by drastically improving the strength compared with conventional metals. For the high-rate cluster deposition and super plastic forming technologies, research and development of aluminum-based light-weight materials have been conducted, which provides excellent strength, toughness, and super plastic formability at room temperature. For the high-density energy utilization and control technology (amorphous-A), super-metals have been investigated as high dew point and corrosion resistance materials used for waste incinerators operated under the very severe conditions. These are expected to be applied to the apparatuses and equipment due to their excellent properties. For the controlled cooling technology (amorphous-B), super-metals with excellent soft magnetic characteristics and degree of shape freedom have been investigated for high performance and high efficiency devices including electric/electronic/communication devices, power transmission devices, and various industrial devices and parts. These are expected to contribute to the creation of new markets and the improvement of international competitive force. 123 refs., 160 figs., 33 tabs.

  19. Development of hydraulic brake actuator for active brake control; Active brake seigyoyo yuatsu booster no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Konishi, Y; Hattori, M. Sugisawa, M.; Nishii, M [Aisin Seiki Co. Ltd., Aichi (Japan)

    1997-10-01

    Recently, application of active brake control systems of the vehicle are increasing. (Vehicle stability control, Panic brake assist ) We have developed a new hydraulic brake actuator for active brake control systems. New hydraulic brake actuator is composed of the three parts. (Hydraulic booster unit, Power supply unit, Control valve unit) This report describes the construction of the new hydraulic booster unit. 2 refs., 10 figs.

  20. Development of crankshaft dynamic stress prediction; Jitsudoji crankshaft oryoku yosoku shuho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, S; Iwamoto, A; Miyazawa, H; Sato, K; Ozaki, H [Honda R and D Co. Ltd., Tokyo (Japan)

    1997-10-01

    In this paper, the development of the simulation model which predicts the stress of the crankshaft under running condition precisely is described. This simulation model considers about the nonlinearity of the oil film stiffness in the main bearing, the dynamic characteristic of the crankshaft system including resonance and the cylinder block stiffness. By the development of this stress analysis simulation, the stress m each part of the crankshaft during durability testing could be precisely predicted. 1 ref., 10 figs.

  1. Development of friction welding method by electric servo motors; Dendo servo shiki masatsu assetsuho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H; Onuma, M; Hasegawa, T; Sakamoto, T [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    The standard friction welding has two methods; the brake method and the inertia method. We have developed a new friction welding method with the electric servo motor system. The forming of plastic fluidity layers of interface is evaluated quantitatively with the feedback control characteristics. The new method has enabled to reduce the heat effect and the burr of friction welding. In the method, we could reduce the getting heat energy, from one-third to half less than the previous methods. 6 refs., 16 figs.

  2. Development of a platoon driving AHS; AHS jikkensha ni okeru gunsoko seigyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Seto, Y; Inoue, H [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    Nissan and the Public Work Research Institute of the Ministry of Construction are developing an Automated Highway System. We are investigating a longitudinal control system in AHS. In this paper, a vehicle control method using two actuators an engine and a brake, is described. Experimental and simulated results are shown. A Platoon driving control method using road-to-vehicle and vehicle-to-vehicle communication is described. And the influence of the communication on the control performance is shown by experiments and simulation. The effects of the communication device and control device mentioned above are verified by experimental results in an AHS field test conducted in September 1996 on a dosed highway. 5 refs., 8 figs.

  3. Hierarchical functional model for automobile development; Jidosha kaihatsu no tame no kaisogata kino model

    Energy Technology Data Exchange (ETDEWEB)

    Sumida, S [U-shin Ltd., Tokyo (Japan); Nagamatsu, M; Maruyama, K [Hokkaido Institute of Technology, Sapporo (Japan); Hiramatsu, S [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    A new approach on modeling is put forward in order to compose the virtual prototype which is indispensable for fully computer integrated concurrent development of automobile product. A basic concept of the hierarchical functional model is proposed as the concrete form of this new modeling technology. This model is used mainly for explaining and simulating functions and efficiencies of both the parts and the total product of automobile. All engineers who engage themselves in design and development of automobile can collaborate with one another using this model. Some application examples are shown, and usefulness of this model is demonstrated. 5 refs., 5 figs.

  4. Development of catalyst for diesel engine; Diesel engine yo shokubai no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ueno, H; Furutani, T; Nagami, T [Toyota Motor Corp., Aichi (Japan); Aono, N; Goshima, H; Kasahara, K [Cataler Industrial Co. Ltd., Shizuoka (Japan)

    1997-10-01

    The new concept catalyst for diesel engine has been developed. When the exhaust temperature is low, SOF and HC are temporarily adsorbed by the adsorbent within the catalyst and are oxidized as the temperature rise. The process of this development have manifested as follows. (1) The coating material is important factor to govern the oxidation activity. (2) SOF is reduced by the coating material in low temperature less than 200degC. (3) The coating material, which has low SO2 adsorbing rate suppress the sulfate formation at high temperature. 2 refs., 11 figs., 1 tab.

  5. Development of super thin foil metal supported catalyst; Chousuhaku metal tantai shokubai no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sanji, F; Takada, T [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    In order to improve warm-up performance, high heat resistance and long life durability of catalysts, the reduction of the metal support heat capacity has been focused. The effects of both reducing foil thickness and lowering cell density on low heat capacity have been investigated. As a result of engine bench and vehicle test, it was apparent that the reduction of foil thickness has greater effects. Newly developed 30 {mu} m foil thickness metal supported catalyst has quicker warm-up performance, and its structural durability up to 950degC is confirmed. 3 refs., 11 figs., 1 tab.

  6. Development of low light-off catalyst; Teion kassei ni sugureta shokubai no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takemoto, T; Ichikawa, S; Koda, Y; Yamamoto, E; Sumida, H; Yamada, H; Shigetsu, M; Komatsu, K [Mazda Motor Corp., Tokyo (Japan)

    1997-10-01

    A new type of three way catalyst was developed in order to reduce HC, CO and NOx in cold exhaust gas. This catalyst consists of double layer, and has a base support material of alumina and oxygen storage components (OSC) loaded with active metals including platinum. palladium and rhodium. It has good light-off performance and high catalytic activity. This catalyst includes two types of OSC. One is CeO2, and the other is CePrO2 that makes possible to improve NOx conversion at high exhaust gas temperature. 8 refs., 13 figs., 2 tabs.

  7. Development of an automatic emergency reporting system; Jiko jido tsuho system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kawai, A; Sekine, M; Kodama, R; Matsumura, K [Nissan Motor Co. Ltd., Tokyo (Japan)

    1995-06-30

    This paper proposes an automatic emergency reporting system as an ASV technology for preventing secondary damage. In the event a vehicle is involved in an accident or other emergency situation, this system automatically reports the vehicle`s present position along with information on the vehicle and owner to an operations center via radio signals. This makes it possible to dispatch an ambulance or other emergency vehicle more quickly. A prototype simulation system has been built consisting of a custom designed control unit for in-vehicle use and a personal computer that simulates an operations center. The interface between the control unit and the personal computer is a wireless modem. The navigation system offered in the Cedric was modified for use as the vehicle location sensor and map database of the operations center. In experiments conducted on the system, information was transmitted from the control unit and shown on a digital map display on the personal computer screen in about ten seconds following activation of an emergency signal. 5 figs.

  8. Both hydrogen and electricity chargeable battery; Suiso to denki de juden kanona denchi kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-01

    Kuriyama group of the Osaka Industrial Research Institute developed a new air-metallic hydride battery that is chargeable by both electricity and hydrogen gas. The battery uses a hydrogen storage alloy as the negative pole and uses active carbon coated with platinum as the positive pole. Potassium hydroxide aqueous solution is used as the electrolyte, and a space is arranged in the negative pole for contacting and absorbing the hydrogen with a good efficiency. The key point is the development of the hydride for energy storage that can well absorbs the hydrogen gas even it is dampened by the electrolyte. And the pole is prepared by pulverized the particles of rare earth hydrogen storage alloy having the particle size smaller than 150 micron meter, forming a Ni layer for a catalyst to absorb hydrogen, adding fluorinated resin dispersant for the sake of repellency and forming a sheet. In a test running, a half of hydrogen storage capacity is realized by charging for 30 minutes. And, 0.6 V electricity of 10 mA per unit pole area of 1cm{sup 2} is continuously obtained for 17 hours during discharging. While a third electrode is formed by nickel hydroxide, the battery is chargeable and dischargeable as the same as nickel hydrogen battery. Low cost and small size can be expected by a combination of respectively prepared fuel battery with nickel hydrogen battery. (translated by NEDO)

  9. Hydrogen battery car developed in Matsuda; Matsuda suiso nenryo denchisha wo kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-01

    Matsuda announced that the hydrogen battery car 'Demio FCEV' was developed by the company. This new type car not only does not need an air humidifying machine, but also supplies the necessary electricity with an ultra capacitor of a large scale condenser. Its maximum output is 40 kw, the highest speed is 90 km per hour, and the accelerating time from the stop state to 40 m is about 5 seconds, the same level as a gasoline car. One time of hydrogen charging serves for 170 km running. As a hydrogen battery car, it is the third one in the world, following the DAIMURA in Germany and TOYOTA. (translated by NEDO)

  10. Study on the current status of biomass energy development; Bio mass energy no kaihatsu jokyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    A survey was conducted on the present status of biomass energy in Japan and abroad and the developmental trend of the latest biomass energy technology. Brazil and the U.S. are most advancing in the biomass energy utilization. Brazil uses sugar cane which is plenty in supply as a raw material, and the U.S. does corn which is the surplus crop. Both countries use the conventional ethanol fermentation technology and produce the petroleum substitution liquid fuel which is in greatest need. As to the technology to convert biomass resource into energy, attention has so far been paid to the development of the production process of the liquid fuel. The latest technology for ethanol fermentation using saccharin and starch as raw materials has already been established in Japan, and the energy-saving type alcohol recovery technology has also reached the stage of practical application. Moreover, as to the ethanol conversion technology with cellulose substrate, the development of the saccharification process will be needed in future. 15 figs., 10 tabs.

  11. Development of position measuring technology by GPS; GPS ni yoru sokui gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ishizaki, T [Ministry of Transportation, Tokyo (Japan)

    1994-07-25

    With regard to the GPS (global positioning system) which uses the satellites launched and administered by the U.S.A. and has been utilized worldwide for ships, automobiles and geodetic surveys in recent years, Ministry of Transport started investigation and research on the application of its position measuring system from FY 1989. In this fiscal year, a study on position measuring methods and selection of the position measuring system to be developed were made, in FY 1991, the real-time functioning and track display were developed, in FY 1992, the initialization aboard the ship, the measure to prevent cycle slip, and the radio data communication technology were developed, and in FY 1993, a long term demonstration experiment presuming its practical use was conducted attaining the expected purpose. In this article, the developed real-time kinematic position measuring system is introduced. Regarding the position measuring methods by the GPS, there are the one point position measuring method and the relative position measuring method. Regarding this newly developed position measuring device, its application to work ships and structures can be considered in various ways. 4 figs.

  12. Development of a new automotive navigation system; Shingata navigation system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sone, M; Nakano, H; Nakayama, O; Tanemura, E; Yoshitsugu, N; Watanabe, M [Nissan Motor Co. Ltd., Tokyo (Japan)

    1996-01-31

    An automotive navigation system was outlined. Features of this system are described below: map display called `Bird View` extending up to the horizon was commercialized; accuracy of determining the vehicle`s present position was realized using new algorithm; and automatic route selection was adopted. Human machine interface of this system also was completely reviewed. `Bird View` was realized by reading plane map data out from CD-ROM and converting them onto the coordinate on the virtual screen in front of the view point. Automatic selection which depends mostly on self-contained navigation adopts the certain way in comparison of the computation position in GPS. To assume vehicle advancing direction, employed were optical fiber gyroscope, geomagnetic sensor, and Karman filter making a good use of advantages of GPS, for the improvement of accuracy. For the automatic distance correction, a function of correcting pulse-distance conversion coefficient was employed, and the free maintenance was realized. 5 figs.

  13. Development of a method to maintain vigilance level; Kakusei teika keigen shuho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Okamoto, Y.; Horiguchi, A.; Ishida, K.; Hata, S. [Mazda Motor Corp., Hiroshima (Japan)

    1995-04-20

    As a part of measures to prevent accidents caused by reduced vigilance and drowsiness of drivers, this paper reports the result of experiments that presents effectiveness of a method to give drivers intermittent auditory stimuli as environmental stimulation. It was found that vigilance decline can be reduced by intermittent auditory stimuli under a laboratory condition using a selective reaction time in monotonous selective reaction works as a parameter; and the effective interval in the intermittence is 30 seconds. A driving simulator was used to prove that the vigilance decline reducing effect by the intermittent auditory stimuli has the same level of effect as chewing gums even under the environment composed of driving operation, vehicle motions, and background noise. However, a number of questions remain yet to be discussed, such as the effect when the ratio of sound presentation time and no presentation time was varied. Furthermore, a number of other physical stimuli in addition to auditory stimulation may be assumed that has effective possibility as vigilance decline reducing stimuli, including hot heat and vibration. It was verified, however, that vigilance decline can be reduced by properly varying the environmental stimulation. 6 refs., 15 figs., 1 tab.

  14. Development and environment of new electric automobile, `Ecovehicle`; Shingata denki jidosha eko vehicle kaihatsu to kankyo

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, H [National Inst. for Environmental Studies, Tsukuba (Japan)

    1996-10-27

    This paper introduces history of the development of an electric automobile, `Ecovehicle`. It is provided with a high overall energy efficiency compared with an engine vehicle. The Ecovihicle is 1.2m in width, 3.3m in length, 2 seating capacities and 910kg in overall weight with serially connected 56 batteries of each 4V, 40Ah and having the total weight of 269kg. Its travel distance per charging is 130km at a speed of 80 k.p.h. This vehicle is capable of running with an energy of approximately one third as much as that of a light car. In addition, the vehicle is provided with polycrystal solar batteries placed on 0.6m{sup 2} area on the roof and spoiler generating 60W maximum. Assuming the annual duration of sunshine is 1,800 hours, charging is possible for 63kWh annually. Assuming the charging efficiency is 83%, charging is possible about seven times, which is an equivalent of travelling about 1,000km annually. The characteristics for example are the employment of brushless DC motor, use of energy saving switching element IGBT in order to realize a low level of loss in the inverter, in-wheel motor system, and storage of storage batteries in a hollow aluminum frame installed under the floor. 2 refs., 5 figs., 1 tab.

  15. Development of RaRaII solar car. Solar car RaRaII no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ohashi, M [Toyota Motor Corp., Aichi (Japan)

    1991-05-31

    A solar car was developed to be able to travel, by utilizing solar energy, as a guiding car for the marathon race in the public road. That car is 210kg in weight, 1 in number of riding persons and 4.8m in smallest rotating radius. Its traveling performance is 44km h in highest speed, 10{degree} in hill-climbing ability and 0.6m s{sup 2} in acceleration. Those principal particulars satisfied the required condition of guiding car for the marathon race. That car was equipped with a polycrystalline silicon type solar cell, 6m{sup 2} in area to generate 870Wp power. A silver oxide-zinc battery, used as a secondary battery to secure traveling in case of rain, is of a performance to travel twice the marathon race road through. To satisfy the public road traveling in safety standard, that car was equipped with head lamps, wiper, direction winkers, rear-view mirrors, etc. As material of the body, aramid fiber and carbon fiber were adopted for securing the rigidity to cover the lightening in weight. That car, as used at an opportunity of intercollegiate marathon relay race, traveled a distance of about 30km which was its entire public road portion of course. 2 figs., 2 tabs.

  16. Development and demonstration of optical polarization controller; Hikari henpa seigyo sochi no kaihatsu to jissho

    Energy Technology Data Exchange (ETDEWEB)

    Kurono, M. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-04-01

    If fiber transmission light can be controlled in a stabilized polarization state, realization of coherent optical communication is anticipated. In the case of adopting it to OPGW, however, it is necessary to compensate high speed polarization variation caused by lightning strike. But this was difficult in the conventional method. Accordingly, a high speed polarization control method was proposed which uses an electric effect of lithium niobate (LN) crystals. In the study, a polarization control unit was manufactured based on the method proposed and the performance was demonstrated. As a result of measuring output light with input light changed in every state of polarization, the object horizontal polarization component obtained a stabilized light intensity at {+-}0.1dB, and a light intensity of the component slipped out of the horizontal polarization was suppressed under -20dB. To cope with the polarization variation by lightning strike, it is necessary to make the control delay 10{mu}sec or below, and improvement in processing unit, etc. may make it possible since LN crystals respond below 1{mu}sec. High speed control of the infinitely continuing arbitrary polarization variation became possible. 14 refs., 19 figs.

  17. Development of MCFC and PEFC technologies; Jisedai nenryo denchi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hori, M; Ozu, H; Sonai, A [Toshiba Corp. Tokyo (Japan)

    1996-06-01

    Next-generation fuel cells under development by Toshiba Corporation are outlined. The molten carbonate fuel cell (MCFC) has become stable in performance, which results from the conversion of the matrix group from the {gamma}-type to {alpha}-type LiAlO2. The cathode material is expected to withstand the elution of electrolyte for 20000 hours. The soft structure separator developed for stack constitution is expected to improve electrical contact and reduce the cost of stack. An appliance has been completed to tentatively produce every element concerned. During an actual operation, the structural soundness of the 2-cell stack was confirmed by thermal load tests. As for the polymer electrolyte fuel cell (PEFC), an interior humidification method has been developed using a porous material for supplying water to the polymer film. The amount of moisture can be controlled, which will enable a larger-area cell. A 1kW-class stack with a world-record-level 1200cm{sup 2} electrode area has been developed, which stack has shown that the target output has been attained. Furthermore, the power generation efficiency of the system including fuel treatment has been examined. 10 figs.

  18. Development of the Nissan hydraulic active suspension. Nissan yuatsu active suspension no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kawarasaki, y.; Fukunaga, Y.; Hasegawa, S.; Okuyama, Y.; Omura, I.; Takahashi, K.; Abe, S.; Tsuruta, E. (Nissan Motor Co. Ltd., Tokyo (Japan))

    1989-12-25

    A hydraulic active suspension system, Nissan original product, was developed and mass produced for the first time in the world. The system incorporates a sufficient power source, a high accuracy sensor and a high response device for continuous and intended vehicle control and at the same time delivers high levels of ride comfort and driving performance. The suspension system has four innovative features: skyhook damping, active roll and pitching control, a frequency-dependent damping mechanism, and active steering characteristics control. Under all road and operating conditions, the system actively suppresses vehicle attitude changes and unnecessary movement, and also gently absorbs inputs from the road. This epoch-making system provides a dramatic improvement in vehicle performance, and has been adopted in the Infiniti Q45 luxury sedan. 2 refs., 20 figs., 4 tabs.

  19. Radar system for non-excavation flowmole drilling; Flowmole koho zenpo kanshi sensor no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nakauchi, T; Hayakawa, H; Tsunasaki, M; Kishi, M [Osaka Gas Co. Ltd., Osaka (Japan)

    1997-10-22

    Technology is discussed of detecting structures buried in the ground by use of a forward-looking sensor mounted on the drill head for the avoidance of collision with such structures during application of the flowmole method in urban districts. In this detection system, pulsating radio signals are emitted from a transmission antenna and the received signals are converted into low-frequency signals in a sampling circuit for eventual display on a B-scope. Since the drill head for flowmole technology is as small as approximately 50-60mm in diameter, experiment is conducted to know the detectability of a very small antenna directed at a buried pipe. The basic phase of the experiment using the very small antenna includes a soil-filled tank test and field test. It is then found that the very small antenna is capable of detecting the steel pipe buried 50cm away from the antenna with the antenna directed at the said pipe. In a test wherein a very small antenna is allowed to rotate on the drill propelling shaft, the design simulating a revolving drill head, it is learned that the detecting system under study will identify the direction in which a buried structure exists. 1 ref., 9 figs.

  20. Development of the sex quality of the material for high; Kotaiyosei suritto puragu zaishitsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Egashira, R. [TYK Corp., Gifu (Japan)

    1999-02-01

    When it works for the stable durability of the gas business slit flag, a spooling is made a problem like heat, and the improvement of the quality of the material is being done. It is formed, and a thermostability spooling causes curving, and the existence of that gap is being improved by substituting some of the bone materials for the special alumina bone material during the bone material and the matrix by being connected with the resistance of the crack development the gap when a crack develops, it branches off .A stable durability is confirmed even in an actual opportunity, and heat shock crack resistance Rst is placed on the effective method as an evaluation of the thermostability spooling. (translated by NEDO)

  1. Research and development of turbofan engine for supersonic aircraft. Choonsokukiyo turbofan engine no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yashima, S [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1992-01-01

    This paper described the researched results of the demonstrator of a turbofan engine for supersonic aircraft (IHI-17). A turbofan engine with an afterburner was experimentally fabricated and various engine tests have been carried out since 1988. Although the engine size is small, the fighter engine specifications were applied to its design and the prior or simultaneous research on each component was carried out. As a result, the system integration technique by which an engine was assembled by integrating each component could be established. New materials and new manufacturing techniques such as turbine blades of single crystal, turbine disks of powder metallurgy and deep chemical milling for a duct were developed to use for the long term engine test and the prospect to commercialization could be obtained. The following techniques have been established and the results satisfying target specifications could be achieved: the three dimensional aerodynamic design of compressor and turbine, the adoption of air blast fuel atomizer to suppress the smoke generation, an afterburner of spray bar system and the mounting type FADEC (full authority digital electronic control) to control the engine with the afterburner. 4 refs., 15 figs., 4 tabs.

  2. Development of GE90 engine with largest thrust. GE90 engine no kaihatsu jokyo

    Energy Technology Data Exchange (ETDEWEB)

    Aono, H [Ishikawajima-Harima Heavy Industries, Co. Ltd., Tokyo (Japan)

    1994-05-01

    The present paper explained the turbofan engine GE90 which is being developed by General Electric Co., USA. That engine is to meet the thrust (takeoff thrust) of 300 to 530kN as required for the new-generation wide-fuselage civil transport plane which is being designed for its planned operation in the 1990's. In April, 1991, the world's strongest thrust of 480kN was achieved with engine elements also confirmed through element test. Thereafter, the engine underwent a flying test on board of Boeing 747 to materialize the planned operation in 1995. Made to be 9 in by-pass ratio and about 40 in overall pressure ratio, the GE90 was given the concept that advantage could be secured in both propulsive efficiency and thermal efficiency. That concept could be materialized by the development of composite fan blade technology and energy-efficient technology which were both demonstrated with an unducted fan. In spite of its pressure ratio of 22, the GE90's high pressure compressor demonstrates its polytropic efficiency which is equal to that of the low pressure ratio compressor. 3 refs., 19 figs., 1 tab.

  3. Development of high reliability dual redundant FADEC. Koshinraisei nijukei FADEC no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Endo, M [Ishikawajima-Harima Heavy Industries, Co. Ltd., Tokyo (Japan)

    1994-05-01

    The control unit of gas turbine for the aircraft jet engine use must draw overall performance in compliance with the thrust commanded by the pilot under all flying conditions of the engine. High reliability is required in flight safety. The present paper explains a developed unit of dual redundant FADEC (full authority digital electronic control) and high-density mounting technology for the electronic devices required by the FADEC. The FADEC unit is composed of two hardware systems with their respective microprocessors of the same structure. Each of both systems can solely control the engine, while they are both commanded by a necessary signal for the dual system operation and connected through a digital by-pass which can exchange the input/output data between them. For the operational confirmation of FADEC unit, its control characteristics were inspected by intentionally putting it out of order at the time of engine acceleration/deceleration and other transient operations. The control system could be switched without control characteristics lost of the engine. 9 figs., 2 tabs.

  4. Quiet STOL research aircraft development program. Teisoon STOL jikkenki kitai kaihatsu sogo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    The airframe development program of the quiet STOL research aircraft (ASKA) promoted by National Aerospace Laboratory, Japan is reported in detail. ASKA was developed based on a C-1 medium-sized troop and freight transport aircraft for the Air Self-Defence Force, and four turbofan- jet engines were substituted for two previous engines. Its first flight was conducted successfully on Oct. 28, 1985 after 8 year development from 1977 to 1985. The ASKA was developed separately on its airframe, engine and flight, and this report includes every related matter to its airframe. The promotion system, budget and executive system are reported in the second chapter, and the design requirements, safety standard and basic design in the third chapter. Several related tests such as wind tunnel test and flight simulation test are reported in the 4th chapter, and the structure and equipment of ASKA are outlined in the final chapter. The appendix includes the line-up of and discussions in the technical committee, the list of newly developed functional parts, the list of design reports and the list of related tests. 50 refs., 8 figs., 23 tabs.

  5. Present developmental conditions petroleum substituting energies in the EU; Sekiyu daitai energy kaihatsu no genjo (EU)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report outlines the policy of development and introduction of petroleum substituting energies, and its diffusion situation in the EU. On the policy, development, introduction and diffusion of petroleum substituting energies in the EU, based on the new EU energy white paper issued in fiscal 1996, the policy of energy and environment in every EU country is first outlined. The policy of and practical approach to petroleum substituting energies in every EU country are next described. In particular, since ALTENER which has been continuously promoted by the EU for 3 years as main control measures against CO2 is newly moving toward the second plan, the trend of ALTENER and the new SAVE2 plan are presented. The content of JOULE-THERMIE is also precisely presented which is the new energy program of the 4th framework R & D program. In relation to the developmental trend of alternative energies to oil in the EU until 2020, its prediction result is presented on the basis of the latest study promoted by EC committee in the ALTENER plan. 10 tabs.

  6. Present developmental conditions of petroleum substituting energies in France; Sekiyu daitai energy kaihatsu no genjo (France)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The French Government most enthusiastically promotes development of bio-gasoline in renewable energy field. EU makes pressure to remove the French Government`s fiscal advantages for bio-gasoline which only benefit French farmers, and the IEA (International Energy Agency) report also estimates no benefit corresponding to the fiscal support cost. Start of the `Eolien 2005` project is attractive in renewable energy field which aims at construction of wind power generation stations of 250-500MW by 2005. The `Eolien 2005` project is mainly supported by Electricite de France (EDF) who guarantees the purchase of produced electric power at a submitted price. In addition to this subsidy activity, EDF decided to positively tackle renewable energy. On R and D efforts for renewable energy, France belongs to the most poor countries among IEA countries, and in addition, the effort is considerably concentrated onto the study on reduction of production cost for bio-gasoline. There were no changes in this situation in 1996. 7 refs., 5 figs., 31 tabs.

  7. Development of plastic pulley by injection molding; Shashutsu keisei ni yoru jushi pulley no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshizumi, F; Funatsu, A; Yazawa, H [Sumitomo Bakelite Co. Ltd., Tokyo (Japan)

    1997-10-01

    We developed plastic pulley for automobile manufactured by injection molding which will reduce manufacturing cost. We have developed product design, injection molding technology especially to improve mechanical strength and phenolic molding compound with good wear resistance and high mechanical strength. We have established `Injection Compression molding` technology to improve mechanical strength of weld portion. We also developed phenolic molding compound which is composed of one step resin and long organic fiber to obtain good wear resistance and high mechanical strength. Manufacturing cost will be reduced by using injection molding combined with lower material cost of the newly developed compound. 12 figs., 2 tabs.

  8. Development of puncture resistance tire tube; Nirinsha no taipankusei kojo cube no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamagiwa, T; Nakayama, K; Kiyota, S; Tanaka, A [Honda R and D Co. Ltd., Tokyo (Japan); Makisaka, N

    1997-10-01

    A new tire tube with a puncture resistance function was developed. The tube is a two-chamber structure having an air chamber and a liquid chamber, and the liquid chamber at the crown-side half of the tube is filled with an anti-puncture sealant during a manufacturing process. In a market test, it was confirmed that the number of puncture cases were reduced by 90 % in comparison with conventional tire tubes by using the newly developed tube. This paper describes the structure of the tube and the characteristics of the tube rubber, and the manufacturing process and durability of the tube. 3 refs., 17 figs.

  9. Advanced soft coverpad made of non-woven fabric; Soft fushokufu coverpad no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hayakawa, t; Kamezaki, K; Tokita, T [Takashimaya Nippatsu Kogyo, Aichi (Japan); Yamada, Y; Ono, H; Araki, O [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    At the present expected to enhance the product-value of automobile, it can be considered that advancement of touching and fitting feeling of seat would be important factors. For the purpose of materializing of these factors, We have noted softening of seat cover and carried out development of cover pad made of non-woven fablic. As a result of pursuing compatibility of soft feeling and durability of the cover pad, we could achieve to ensure the quality required for the material as the seat cover pad. 3 refs., 15 figs., 4 tabs.

  10. Development of air fuel ratio sensor; A/F sensor no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sakawa, T; Hori, M [Denso Corp., Aichi (Japan); Nakamura, Y [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    The Air Fuel Ratio Sensor (A/F sensor), which is applied to a 1997 model year Low Emission Vehicle (LEV) was developed. This sensor enables the detection of the exhaust gas air fuel ratio, both lean and rich of stoichiometric. It has an effective air fuel ratio range from 12 to 18 as required for LEV regulation. It has the fast light off, - within 20 seconds - to minimize exhaust hydrocarbon content. Further, it has fast response time, less than 200 msec, to improve the air fuel ratio controllability. 3 refs., 7 figs.

  11. Advanced slab polyurethane foam with feather touch; Soft feather urethane foam no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, Y; Ono, H [Toyota Motor Corp., Aichi (Japan); Mori, A; Yamaguchi, N; Nakamura, T [Bridgestone Corp., Tokyo (Japan)

    1997-10-01

    Automotive seat plays an important part, which are not only retention of sitting position, but also comfort and high-class feeling. Wadding, which is a part of the seat, is a key component for the sitting comfortableness. This paper is concerned with advanced slab polyurethane foam with feather touch feeling. The compounding of formation, foaming process and reliability of mass production is studied. 2 refs., 10 figs., 3 tabs.

  12. Development of multiplexing network for air conditioner systems; Eakon yo LAN system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Matsumoto, T; Nakazawa, Y; Nakase, M; Sato, Y [Nissan Motor Co. Ltd., Tokyo (Japan); Nomura, M; Okasato, Y; Sunaga, H [Calsonic Corp., Tokyo (Japan)

    1997-10-01

    Plural air flap actuators of the air conditioner system in a vehicle have been integrated into a single-type actuator using two newly developed technologies: super-low-cost multiplexing network technology and digital motor control technology with a 1-bit A/D converter. The number of harnesses and connectors and the handling load of the air conditioner control microcomputer are reduced, so that we succeeded in sharply reducing the cost of the air conditioner system. 9 figs., 2 tabs.

  13. Development of hybrid system for mass productive passenger car; Joyoshayo ryosangata hybrid system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Abe, S; Sasaki, S; Matsui, H; Kubo, K [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    The Toyota Hybrid System has two power sources which engage depending on driving conditions. An improved efficiency gasoline engine provides the main power to drive the wheels, as in conventional automobiles. Drive power can also be supplied by an electric motor, which derives its electricity from a battery and a Generator. Fuel efficiency is further boosted by other measures, such as automatically cutting the engine when the vehicle is at a stop and regenerating the energy accumulate during deceleration. Compared with conventional vehicles with a 1.5-liter engine running in 10 {center_dot} 15 mode, the CO2 emissions are reduced by half. Moreover, with the use of a motor to reduce engine load during acceleration, HC, CO, and NOx emissions are cut significantly low levels. 13 figs.

  14. Development of Toyota new 1GZ-FE engine; Shingata V12 gasoline engine no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, H; Asahi, T; Goto, M; Endo, K; Terada, M [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    The first V-12 cylinder engine for passenger car in Japan, the 1GZ-FE, which is the status of high luxury vehicles has been developed. In order to proceed the merit of V-12 cylinder engine, Intelligent Variable Valve Timing (VVT-i) system, Slant squish combustion chamber, Iridium pole spark plug and Intelligent electronic throttle control system were introduced. Through these features this new 1GZ-FE has achieved an overwhelming smoothness and quietness and yet highest torque among the same displacement engine at low and medium engine speed. Additionally the 1GZ-FE achieved good fuel economy and high reliability which exceed any other competitors. 14 refs., 4 figs.

  15. Development of roller type side slip tester; Roller shiki side slip tester no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nishiyama, S [Hiroshima City Industrial Technology Institute, Hiroshima (Japan); Harada, S; Harada, K

    1997-10-01

    This paper presents a new development of roller type side slip tester (RTSSI). The test equipment consists of four parts, which are developed in this research. These are a roller part, a control part, a remote control part and a CRT part. In this study, we especially investigated the mechanism and performance between tire and roller. We analyzed the amount of side slip with various toe angles. The developed tester is examined under the conditions that is considered in industrial applications. We investigated the influences of toe angle, size of tire, pressure of tire, coefficient of friction between tire and roller, pushing force of tire, revolution velocity of roller, axle load and so on. The validity of the developed RTSST is confirmed under these conditions. It was found that the RTSST can be used in practical use. Some measurement results are presented in the form of parametric plots. And we also compared measurements data between the RTSST and that of flat type using several automobiles. 4 refs., 8 figs., 4 tabs.

  16. Development of refrigerator insulation with reduced CFC-11. Reizokoyo flon sakugen uretan dannetsuzai no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kai, H.; Fukuda, K.; Yoshioka, M. (Sharp Corp., Osaka (Japan))

    1992-11-10

    Polyurethane thermal insulator in which the usage of CFC-11 is 50% reduced by increasing the percentage of water has been developed for the purpose of reducing polyurethane-foaming CFC-11 used as thermal insulator of refrigerators. In this new water-intensive feedstock system, the overall OH-value in polyol was lowered; the usage of aromatic amines was curtailed; and the amount of sorbits was increased so as to secure adhesiveness at the foaming jig temperature of 35[degree]C. As for the improvement of fluidity, a combination of four kinds of polyols offered viscosity in the same level as in the conventional ones. Thermal conductivity was worsened, but the rate of its drop could be controlled below 3% by some measures such as homogenization of stock materials, choice of a suface-active agent which makes foam bubbles minute, etc. Concerning curing property which has a large effect on productivity, a reaction type amine-based catalyst delaying thickening behaviour at the time of foaming was selected and a gelling promotive tertiary amine-based catalyst which can develop foam curing promptly was combinedly used to reduce curing property from five minutes in the past to four minutes. 2 refs., 6 figs., 14 tabs.

  17. Development of practical solar-electric vehicle; Jitsuyo fukyugata solar denki jidosha no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Saito, S; Fujinaka, M [Tokyo Denki University, Tokyo (Japan)

    1997-11-25

    The paper reported on a Tokyo-Nagoya travel test on a practical spread type solar-electric vehicle, Solar-EV. A comparative study was made running the same type gasoline vehicle, GV. The measured power consumption amount of Solar-EV is 57.6 kWh. By converting it into Mcal unit, an energy consumption amount of 49.5 Mcal was obtained. Further, as to GV, the energy consumption amount of 316 Mcal was obtained using the amount of supply of gasoline (mean heating value: 8.4 Mcal/h) of 37.6 l and the fuel consumption of 16.2 km/l. Accordingly, the energy consumption amount of Solar-EV became a sixth of that of GV. In the cost comparison, the cost of Solar-EV was 1,440 yen (power source price: 25 yen/kWh), which is about a third of that of GV, 3760 yen (gasoline unit price: 100 yen/l). Monocrystal Si solar cells, 270W, installed on hood/roof are connected to the main 288V system (the auxiliary 12V system is amorphous Si), and generate power 4.4 kWh during travel. A total power consumption amount of Solar-EV in the total travel (Tokyo-Nagoya) is 79.9 kWh including the auxiliary system, approximately 6% of which was to be supplied from solar cells. 1 ref., 6 figs., 3 tabs.

  18. Development of solar power generator system; Taiyoko netsufukugo hatsuden system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kisara, K; Kumagai, T; Niino, M; Chen, L; Eguchi, K [National Aerospace Laboratory, Tokyo (Japan)

    1997-11-25

    Described herein is a new hybrid solar power generator system, in which solar energy is separated into the light and heat components by a wavelength-selective filter before being directly converted into electric power, the former for the amorphous solar cell (ASC) unit and the latter for the thermoelectric unit. These units complement with each other to enhance overall efficiency. The ASC unit should have a higher efficiency when it works on the light component, because the heat (infrared) component increases cell temperature and decreases its output. For the ASC unit, the effects of the filter have been tested. The thermoelectric unit, generating power by the Seebeck effect, should have a higher efficiency, if heat flux passing through the unit can be increased, because of increased temperature differential, to which voltage produced increases proportionally. For the thermoelectric unit, heat is collected by a parabolic mirror unit from sunbeams received by a heliostat. Characteristics of these units are grasped almost as expected by the tests. 4 refs., 11 figs., 1 tab.

  19. Development of automatic high-concentration boron measurement technique; Konodo hoso jido sokutei gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Maeda, T.; Honda, S.; Ito, A. [Kyushu Electric Power Co. Inc., Fukuoka (Japan)

    1997-03-01

    The technology that can automatically measure the boron concentration in boric acid water was developed. A high-concentration boric acid solution must be held at a high temperature to prevent the deposition. Skill and precision ({plus_minus}0.2 to 0.3% for 10 to 2500 ppm as boron concentration, and {plus_minus}2 to 3% for 2500 to 25,000 ppm) are required to analyze the boric acid solution manually. In theory, the boron concentration in a wide range can be measured, and boron has a constant-temperature function. A density hydrometer method that facilitates the treatment and calibration in high precision and at low cost was chosen. The vibration period generated when vibration is given to the solution specimen put in a U-tube is higher as the density is lower. On the basis of this theory, the density of a specimen can be obtained according to the relation with the same data of the known-concentration boric acid water. The high-concentration boric acid water that cannot be measured by the existing boron densitometer can be measured directly. It can also be measured in a low-concentration area. The technique can be used in a laboratory as the simplified method that is replaced by the current manual analysis. The reduction effect of analytical chemical`s waste liquid can also be expected. In the electric power industry, automated equipment is required for high efficiency and labor saving. 13 figs., 3 tabs.

  20. Development of advanced coal cleaning process; Kodo sekitan kaishitsu gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Osaka, S [Center for Coal Utilization, Japan, Tokyo (Japan); Akimoto, A; Yamashita, T [Idemitsu Kosan Co. Ltd., Tokyo (Japan)

    1996-09-01

    This paper aims to develop a clean coal production process which excellently removes environmental pollutant, is low-costed, and need no particular systems for distribution of products. The result of the development was described paying attention to column flotation which is a technology to high-efficiently select particulate regions, particulate heavy media cyclone, magnetic separation, and the basic design of the process into which those above were integrated. The two-stage selection process, which is an integration of column flotation and particulate heavy media cyclone into the conventional coal preparation equipment, can produce low-ash clean coal at high separation efficiency and also suppress the rise in processing cost. This process was also effective for removal of sulfur content and trace metal elements. The use of clean coal at power plant can be effective for not only the reduction in ash treatment amount, but the aspect of boiler operation characteristics such as heat transfer efficiency of boiler furnace wall, ash related troubles, loads of electrostatic precipitator, loads of flue gas desulfurization facilities. 17 figs., 5 tabs.

  1. Development of pressurized coal partial combustor; Kaatsu sekitan bubun nenshoro gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Kawamura, K [Kawasaki Heavy Industries, Ltd., Kobe (Japan); Tanaka, T [Chubu Electric Power Co. Inc., Nagoya (Japan); Muramatsu, T [Electric Power Development Co. Ltd., Tokyo (Japan)

    1996-09-01

    The coal partial combustor (CPC) uses a combustion technology with which coal is burned at elevated temperatures and under revolution, the constituents are captured on the furnace wall and removed as molten slag from the furnace. This is a combustion technology to reduce load of ash on subsequent devices. To generate a molten condition, it is necessary to raise the combustion temperature as high as possible (to about 1600 degC in the furnace), but this is effective for a gas turbine composite power generation system. An efficiency of higher than 45% may be expected at the power transmission terminal. As an operation on subsidy from the Agency of Natural Resources and Energy, the normal-pressure CPC technology has already been established, and a research on pressurized CPC is being progressed since fiscal 1991. The research is in progress with a schedule that elemental tests for 7 tons per day production are conducted until fiscal 1995, a 25 tons per day pilot plant will be completed by November 1997, and verification tests for long-term continuous operation will be implemented until 1998. The 7 tons per day elemental tests have identified gasification performance and slag extraction performance using five types of coal having different properties. 7 refs., 10 figs., 4 tabs.

  2. Development of pressurized internally circulating fluidized bed combustion technology; Kaatsu naibu junkan ryudosho boiler no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ishihara, I [Center for Coal Utilization, Japan, Tokyo (Japan); Nagato, S; Toyoda, S [Ebara Corp., Tokyo (Japan)

    1996-09-01

    The paper introduced support research on element technology needed for the design of hot models of the pressurized internally circulating fluidized bed combustion boiler in fiscal 1995 and specifications for testing facilities of 4MWt hot models after finishing the basic plan. The support research was conduced as follows: (a) In the test for analysis of cold model fluidization, it was confirmed that each characteristic value of hot models is higher than the target value. Further, calculation parameters required for computer simulation were measured and data on the design of air diffusion nozzle for 1 chamber wind box were sampled. (b) In the CWP conveyance characteristic survey, it was confirmed that it is possible to produce CWP having favorable properties. It was also confirmed that favorable conveyability can be maintained even if the piping size was reduced down to 25A. (c) In the gas pressure reducing test, basic data required for the design of gas pressure reducing equipment were sampled. Specifications for the fluidized bed combustion boiler of hot models are as follows: evaporation amount: 3070kg/h, steam pressure: 1.77MPa, fuel supply amount: 600kg-coal/h, boiler body: cylinder shape water tube internally circulating fluidized bed combustion boiler. 4 refs., 4 figs.

  3. Development of a robot system for converter relining; Tenro chikuro robot system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ito, Y; Kurahashi, M [Nissan Motor Co. Ltd., Tokyo (Japan)

    1995-09-12

    In steelmaking plants, the relining work of converters requires plenty of manpower and time. Recently, the number of expert brick workers has decreased, and it has been difficult to get together the necessary number of workers for the converter relining. To solve these problems, a robot system has been developed and realized for the converter relining. The system consists of two intelligent robots and an automatic brick conveying machine. With visual function and flexibly controlled hands, the robot enables to heap up bricks in the same manner as expert workers do. The automatic brick conveying machine consists of roller conveyers and a cage lifter that convey bricks on palettes to the suitable position for the robot to easily handle. This robot system has enabled to save much labor for the converter relining. 8 figs.

  4. Development of a downhole seismic source with controlled waveform; Hakei seigyogata kochu shingen no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kuroda, T; Ikawa, T [Japex Jeoscience Institute, Tokyo (Japan); Sato, T [Meiho Engineering Co. Ltd., Tokyo (Japan); Kakuma, H [Akashi Corp., Tokyo (Japan); Onuma, H [Engineering Advancement Association of Japan, Tokyo (Japan)

    1997-05-27

    A downhole seismic source which can output continuous waves having arbitrary waveforms was developed. The development was targeted to make tomographic exploration purposed to evaluate geological properties of a ground bed before and after constructing a building in a ground several hundred meters deep from the ground surface. The source is considered to be used in an environment consisting of soft rocks or more robust rocks and having no casing. It can be used in a well hole having a diameter of 100 mm, is capable of measuring P and S waves in a distance between well holes of up to 100 m, can be used at a depth of up to 500 m, and can output waveforms having seismic source spectra of up to 1000 Hz. An oscillation actuator using laminated piezo-electric elements was used for the oscillation element. The seismic source consists of a hydraulic device to clamp the equipment onto hole walls, piezo-electric elements as the oscillation element, and an inertia weight for applying vibration from above and below. To make an oscillation, the main body is first clamped on the hole wall. For horizontal oscillation, the piezo-electric elements contained in a clamping device provide the horizontal oscillation. For vertical oscillation, the piezo-electric elements placed below the main body oscillates the inertia weight. The initially targeted specifications have been achieved. 3 refs., 4 figs., 1 tab.

  5. Fiscal 1997 report on the R and D result of industrial science and technology. R and D on super metal (R and D on innovative raw metal materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Study was made on the applicability of mechanical milling (MM) and mechanical alloying (MA) to Fe system alloys. Metastable austenitic stainless steels such as SUS316L and SUS304L form {alpha} phases by strain induced transformation due to MM, and are subjected to further plastic deformation. Nano-size fine structure was obtained through inverse transformation into austenite({gamma}) by heat treatment or high-temperature sintering of MM powder. Fine microduplex structure of 620nm in average crystal grain size was obtained for SUS316L. This material showed nearly 3.3 times higher 0.2% tensile proof stress, nearly 1.8 times higher tensile strength, and 35% higher elongation than conventional ingot steels. Solid solution powder of 12Cr-Mo-W ferritic steel was sintered by hot isostatic pressing (HIP) under low- temperature and ultrahigh-pressure conditions of 650degC and 588MPa. The as-HIP`ed sample and sample annealed at 800degC showed average {alpha} grain sizes of 33 and 50nm, respectively, and a strength twice as high as that of 12Cr steel. 97 refs., 60 figs., 18 tabs.

  6. PV glass curtain walls; Kenzai ittaigata taiyo denchi gaiheki no kaihatsu (glass curtain wall eno tekiyo)

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, T.; Iwai, T.; Ouchi, T.; Ito, T.; Nagai, T.; Shu, I. [Kajima Corp., Tokyo (Japan); Arai, T. [Showa Shell Sekiyu K.K., Tokyo (Japan); Ishikawa, N.; Tazawa, K.

    1997-12-20

    Reported in this article are PV (photovoltaic) modules now under development for integration into building walls. First of all, the power generating capability of PV modules and appropriate use of the generated power are studied, and the performance (resistance to fire or incombustibility, strength and durability, appearance and design, and dimensional standardization) that such outer wall materials are to be equipped with are determined. Next, module development, installation technique, computer graphics-aided facade designing, and real size module-using proof test are studied before installability, the power to be generated, and designs are finalized. In the development of modules, design evaluation involves the combining of various kinds of glass, solar cells, back sheets, and fillers, and the importance is confirmed of the prevention of insulation degradation around the modules. As for the methods of installation, the gasket method and aluminum sash method, etc., are tested. In the study of facade design, it is found that various expressions are possible by properly choosing gasket colors, module types, and kinds of glass to cover the openings. 1 ref., 6 figs., 3 tabs.

  7. FY 2000 report on the results of the regional consortium R and D project - Regional new technology creation R and D. First year report. R and D of medicine toxicity assessment use hepatocyte chip; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium kenkyu kaihatsu / chiiki shingijutsu soshutsu kenkyu kaihatsu. Dokubutsu dokusei hyokayo kansaibo chip no kenkyu kaihatsu (dai 1 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Judging that in the beginning of the toxicity test, the necessary information/knowledge are acquired not by using animal itself but only by using liver system (hepatocyte), the development was proceeded with of the hepatocyte chip substituting for the animal experiment. Studies were made in the following five fields: 1) design of functional matrices; 2) development of the pharmacological assessment technology; 3) development of cell sensing technology/biosensor fabrication; 4) study of a possibility and the limit of cell patterning technology; 5) survey of the market scale. In 1), studies were made of the establishment of the 3D culture method for hepatocyte and the construction of hepatocyte models for medicine assessment using pieces of liver. In the latter, by including capsule using the sugar introduced with galactose residue which is special sugar of hepatocyte to alginic acid and chitosan which are natural polymer and also hepatocyte isolated into sponge, aggregate was formed, and its use as a medicine assessment use liver model was tried to be made. (NEDO)

  8. FY 1996 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (Keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    Organosilicon polymers are highly innovative materials having high performance and novel functions, and they can be widely applied. The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis of highly conjugated polymers is investigated. In (2), novel organosilicon polymeric materials have been developed, which would be applicable to direct lithography of electronic circuits, and which could contribute to simplification of the circuit formation process. In (3), the research aims at development of new silicon-based polymer materials with luminescent function which can be applied to the large size electro-luminescent display devices. In (4), new materials with visible light absorption have been synthesized through the molecular design and synthesis. The photo-carrier generation was observed. 107 refs., 86 figs., 23 tabs.

  9. Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A phenomenon of excess heat generation through the electrolysis of heavy water using palladium metals as electrode can be recognized as new hydrogen energy. Its mechanism has been investigated for four years since FY 1993. In FY 1993, the New Hydrogen Energy Demonstration Research Center and the New Hydrogen Energy Demonstration Laboratory were organized, and the research was initiated. For the excess heat generation demonstration model tests, two types of electrolysis experimental units were constructed, and the Pd/D-based electrolysis experiments were initiated. For the measurements of excess heat using an open type electrolysis cell, there were rather large errors ranging from -13% to +7%. It is necessary to improve the accuracy. For the measurements using a fuel cell type electrolysis cell, generation of the excess heat ranging from 0% to 6% was observed. For the validity of this, it is required to confirm the long-term stability of calibration and cell components. For the correlation between the increase in absorbing rate and the generation of excess heat, results of 2 to 3% lower were obtained. 28 refs., 89 figs., 26 tabs.

  10. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). The R and D aims at establishment of observation/manipulation technology of atoms and molecules as common basic technology in various industrial fields such as new material, electronics, bio-technology and chemistry. The R and D thus aims at establishment of observation/manipulation of solid surfaces and DNA organic molecules, formation of fine structures of atomic surface arrangement, and calculation/ simulation for predicting a reaction theorem of atom and molecule surfaces. In fiscal 1997, research was made on improvement and development of computer simulation environment, and description of an excited state of electrons by Green function. Establishment of a construction method and computation code is under investigation for pseudo- potential dependent on excitation energy. Survey was made on research trends of the atom technology by visiting overseas academic societies and institutions. International Symposium on Atom Technology was also held in Tokyo in Nov. 1997

  11. Development of Fresnel lens for improvement of rear visibility; Shikai kojo Fresnel lens no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Iwamoto, K; Sanada, C; Tsukino, M [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    Fresnel lenses have been widely used to increase the visual field around vehicles for drivers. However, internal reflection in these lenses has been an obstacle in producing dear images. This internal glow is generated by incident light from an unexpected direction reflecting on the non-lens surface or radiating from the non-lens surface of the Fresnel lens. The cause of internal glow has been made dear combining louver film with the lens. The newly developed technology removes obstacles in producing dear images by reducing internal glow. 7 figs.

  12. Development of film antenna for diversity reception; Diversity taio film antenna no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Shigeta, K; Taniguchi, T; Kubota, K [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    Based on the principle of capacitance-loaded window antennas, a new film antenna construction pasting an antenna element on a defogger element printed on a rear window was found. The film antennas show high reception performance, and can be used as television diversity antennas or a VICS-FM multiplex antenna. This paper describes the antenna design concept, the antenna construction and the application to a recreational vehicle which styling is 1.3-Box wagon for the electric accessory. 2 refs., 11 figs.

  13. Development of lane change aid system; Lane change aid system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Uemura, H; Yoshida, T; Butsuen, T [Mazda Motor Corp., Hiroshima (Japan); Sakai, N; Nakano, T; Nakamoto, T

    1997-10-01

    We have developed a lane change aid system, which detects vehicles behind in adjacent lanes with CCD images, shows the driver the information of vehicle location with a head-up display, and warns him/her if necessary. By comparing the brightness on two CCD images, distance distribution along several CCD lines is measured. To assure the effective vehicle detection on public roads, we have developed a detection algorithm which distinguishes vehicles and guard-rails by observing the patterns of measured distances. We will show the system configuration, detection logic, and the system evaluation on public road. 5 refs., 12 figs.

  14. Development of application technology of ultrasonic wave sensor; Choonpa sensor oyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hosoya, H; Hikita, N; Sasaki, H; Kore, H [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    We have developed parking assist system, which informs a driver the closing point and distance to the objects such as other vehicle, wall and pole around the own vehicle at parking area and makes parking maneuverability easy. This system is based on the range detection technology using ultrasonic wave sensor. We have improved the detecting ability in short range of about 20cm by reducing the reverberation of transmitting wave signal and controlling sensitivities of signal intensity and threshold line. We will show mainly the improvement of short range detection of ultrasonic wave sensor, and briefly the performance of parking assist system. 1 ref., 14 figs., 1 tab.

  15. Development of mechanical shield docking method; MSD (mekanikaru/shirudo/dokkingu) koho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yokota, I. [Tokyo Metroplitan Government Water Supply Bureau, Tokyo (Japan); Watanabe, T.; Hagiwara, H. [Shimizu Corp., Tokyo (Japan); Nishitake, S. [Mitsubishi Heavy Industries Ltd., Tokyo (Japan); Endo, M. [Obayashi Corp., Osaka (Japan)

    1993-09-20

    For the construction works of underground tunnels, mainly the shield method has so far been adopted, but in order to make underground junction of shield machines, the method of utilizing a shaft or the method of improving the earth by the auxiliary methods such as chemical feeding have been adopted. However, either method has restriction for its practical application. The MSD method uses no auxiliary method at all, can join directly two shield machines mechanically underground, has high water stoppability at its junction, is applicable for either of shield machines of slush type or mud pressure type, and is the method to solve totally various problems in the existing joining methods. This method is the one that two shield machines, one on the out-pushing side and another on the in-receiving side, progress from both sides and face each other, then the both are joined mechanically for unification by pushing a steel penetration ring built-in the out-pushing shield machine to the rubber ring built-in the penetration chamber of the in-receiving shield machine. After joining, the shield machines are disassembled for removal leaving the junction only, and the secondary lining is done with concrete. 6 figs.

  16. Development of remote controlled blasting system for tunnels; Tunnel yo enkaku seigyo happa system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, S.; Kawamura, M.; Hirosaki, Y. [NOF Corp., Aichi (Japan)

    1997-06-30

    A downsized wireless blasting system has been developed for tunnel construction in the mountainous districts. This system consists of an oscillator, loop antenna, and initiator. The ac magnetic field is generated in the loop antenna using 550 Hz ac generated by the oscillator, to induce the electro motive force between both ends of receiver coil in the initiator. It is stored in the capacitor after rectification, to initiate the detonator by discharging with the firing signal. This system has been developed by downsizing the conventional RCB (remote controlled blasting system) for underwater blasting, and unmanned operation is planned in future. An oscillation frequency, 550 Hz with an actual result has been adopted. The arm length of loop antenna is 3 m, which can be installed in the tunnel. Various receiver initiators were fabricated as a trial. A convex type was adopted due to its excellent receiving performance. The receiving performance was improved by increasing the magnetic induction and decreasing the power loss. After receiving voltage of the receiver initiator was confirmed, field initiation tests were conducted. Initiating and blasting were successfully carried out. 5 refs., 15 figs., 3 tabs.

  17. Power conditioner without isolation transformer; Toransuresu power conditioner no shohin kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Okado, C; Itami, T; Kimoto, K [Toshiba Corp., Tokyo (Japan)

    1996-10-27

    A light-weight downsized and high efficiency transformer-less type 4 kW power conditioner (inverter) has been developed. This power conditioner insures the system interconnection protection by monitoring the voltage of two single-phase three-line circuits. The power conditioner has weight of 17.5 kg and efficiency of 94%. Potential fluctuation of photovoltaic cells due to the switching of power devices at the inverter was reduced. Output capacity was reduced in the low input voltage range. Outflow of DC component was prevented in high accuracy by usually correcting the zero point drift of detector, and by using the current detector with excellent linearity. To detect the DC ground fault, and to trip the output side breaker locating at the ground fault current pass, a zero phase converter detection circuit has been developed, by which the DC component can be detected at the DC input side. As a result of performance verification, the efficiency, power factor, EMI level, protection of outflow of DC component, protection of ground fault, protection of single operation detection, and noise level were satisfied. This system is prospective for the diffusion of photovoltaic power generation in the future. 3 refs., 8 figs., 1 tab.

  18. FY 1998 result report on development of superconductive power application technologies. Pt. 1. Research and development of superconductive wire materials / Research of a total system / Research and development of a freezing system / Demonstration tests; 1998 nendo chodendo denryoku oyo gijutsu kaihatsu. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Superconductive technologies are introduced into electric power devices for attempts of achieving higher stabilization, density and efficiency, as well as size and weight reduction and improvement in performance of the devices. The project has been worked on since fiscal 1998 as part of the New Sunshine Project. Fiscal 1998 being the eleventh year has taken the following subjects as the research promotion policies: establishment of plans targeted at accomplishment of the goals of the project; adequate and reliable implementation of verification of technological assignments; and steady and efficient demonstration tests. Subsequent to the previous year during which site demonstration tests were completed on a low-speed responsive model machine, the site demonstration test has begun on the ultra high-speed responsive model machine as the final stage of the project. The ultra high-speed responsive model machine was coupled with a freezing system and a load synchronizing machine, and different kinds of test were carried out where good results were obtained. Researches were conducted on characteristics improvement and device element technologies aimed at achieving the practical application level by utilizing the respective features of AC metal-based wires and oxide-based wires, where sound results were obtained. Also in an improved freezing system, valuable data were attained as part of establishing the basic technologies for a superconductive power generation system. (NEDO)

  19. Achievement report for fiscal 1996 on the research and development of superconductor technology to power generation. Pt. 1. Research and development of superconducting wire, generator, total system, and refrigeration system; and verification test; 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    In the research and development of superconducting wires, studies are conducted to increase the current capacity of NbTi and Nb{sub 3}Sn metal wires and to improve their properties, and to increase the current capacity of oxide materials and improve their performance making full use of the features of each manufacturing method. In the development of superconducting generators, a slow excitation response type is tested for verification, and a good result is attained; and a quick excitation response type is tested for field winding static excitation, and good performance is exhibited. Using the results so far achieved, the 200,000kW class pilot machine concept design is reviewed. In the study of total systems, feasibility is studied of a quench test for the 70,000kW class machine through simulation analyses, etc. In the development of refrigeration systems, efforts are exerted to improve on the conventional type in terms of reliability and to further improve on the improved version in terms of performance and space-saving feature. One of the endeavors involves the development of a He Brayton cycle turbine driven compressor. A multilayer cylindrical rotor is verified in terms of functions, characteristics, reliability and durability, and various data are collected toward the development of a pilot machine. (NEDO)

  20. Synthesis of new erodable polymers response to environmental stimuli; Atarashii kankyo chowagata bunkaisei plastic no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kato, M; Nagasaki, Y [Science University of Tokyo, Tokyo (Japan). Faculty of Industrial Science and Technology

    1997-02-01

    This report relates to the designing of functional materials that decompose in response to various signals. A derivative of {alpha}-bromomethylstyrene is caused to act on the living anions of {alpha}-methylstyrene for the synthesis of a pyrolytic polymer having unsaturated groups at its terminals. The terminal double combinations of this polymer split under the influence of heat, acid, or base for depolymerization which is quantative, and the decomposition temperature may be controlled by replacing terminal phenylallylic groups with methyl groups or phloro-groups. Furthermore, a novel polythyramine polymer is synthesized with its principal chain constituted of NCH2CH2Si, the principal chain easy to disintegrate when exposed to an electron beam. The polymer is signal-responsive and may be patterned by use of an electron beam. As a temperature-responsive polymer with the hydrolytic feature controlled, poly(thyroxy ethylene glycol) is obtained from a derivative of diaminosiloxane and oligo-oxyethylene. This is a high-mobility, temperature-responsive material whose hydrolysis may be controlled. 3 refs., 2 figs.

  1. Development of practical diet for aquaculture of Japanese flounder; Gyofun wo sakutenshita hirameyo shiryo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kikuchi, K.; Furuta, T.

    2000-07-01

    Feeding experiments were conducted to examine the potential use of defatted soybean meal (SBM) in combinations with blood meal (BM), corn gluten meal (CGM) and freeze dried meat of blue mussel (BMM) as a partial replacement of fish meal (FM) in the diet of Japanese flounder. Availability of CGM in combinations with BM and/or BMM was also examined. Juvenile fish of about 4 g in initial body weight were fed diets to satiation twice daily, 6 days per week for 8 weeks at 20 degree C in both feeding experiments. Weight gain of fish fed diet replacing 45% FM protein with SBM was not different from that of fish fed the control diet containing FM as a protein source, however, feed efficiency (FE) in fish fed the SBM diet was significantly lower. Growth and feed performance of fish fed diet replacing 45% FM protein with SBM and BM were comparable to those of fish the control diet. Inclusion of 5% BMM for equal amount of SBM in the SBM-BM diet improved the growth and FE of the flounder remarkably and both values were significantly higher than those in the control. Replacing 55% of FM protein with SBM and CGM or SBM and BM resulted in poor growth performance. There were not marked differences in hematological characteristics together with proximate composition of the whole body of cultured fish fed the dietary treatments. Weight gain and FE of fish fed diet replacing 40% FM protein with CGM were inferior to those of fish fed the control diet containing FM as a protein source. Replacement of 40% FM protein with CGM and BM made those parameters worse. Inclusion of BMM in CGM-BM diet did not improve the growth of fish. Adverse effects of replacing FM protein with CGM and/or CGM and BM were stronger with increasing replacement level. These results indicate that SBM is highly available as alternative protein source for fish meal in the diet of Japanese flounder. SBM in combination with BM successfully replace about 45% of FM protein in the diet without supplemental amino acids. Furthermore, it is suggested that more replacement can be attained with inclusion of 5% BMM in the SBM diet. CGM is not considered to be useful ingredient on practical bases. (author)

  2. Jet engine R and D and I; Watashi to jet engine kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Murashima, K. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1998-06-10

    My efforts towards at the development of aeroengines since the end of the war are described. The J3-7 engine propelled the T1 trainer plane, and was installed as booster aboard the P2J antisubmarine patrol aircraft. It was the first jet engine that Japan produced after the end of the war, and had been in use until quite recently. I took part in the construction of a prototype of the JR100 series designed to serve as VTOL (vertical take-off and landing) aircraft lift engines, and in the test thereof. As the shift from turbojet to turbofan proceeded, I participated in the development of the FJR710 engine under the guidance of National Aerospace Laboratory, and the product was installed aboard an experimental STOL (short take-off and landing) aircraft Asuka. I next joined a Defense Agency initiative for a reheat turbofan to replace the J3 aboard trainer plane, and the result was the low bypass ratio/high output F3 engine. In 1989, Ministry of International Trade and Industry decided for a large-scale project of developing an engine for a next-generation supersonic transport, and the HYPR (Super/Hypersonic Transport Propulsion System) project was started. The project was participated in by manufacturers from overseas, which were GE, P and W, RR, and SNECMA. The foreign corporations worked on an equal footing with the Japanese parties, and collaboration between the participants was smooth, with each party endeavoring in the field they were good at. The project will be concluded as scheduled in fiscal 1998. (NEDO)

  3. Assessment report on the development of functionally inclined material; Keisha kinosei zairyo no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Concerning a project whose aim is to develop heat resistant engine members through the application of the concept of functionally inclined materials, deliberation and assessment are made of the meaning of its implementation, validity of the research program, research achievement, etc. The project deals with a specimen, diameter 150mm or more and thickness 5mm or more, built of a zirconia/stainless steel-based functionally inclined material, and its goal is to develop technologies for optimizing the baking process for the said specimen, baking system and related devices, assessment technique, tribological assessment technique, etc., and it is inferred that these targets are reasonable. As the result of this research, an energy-efficient (power consumption reduced to 1/3 to 1/5) practical rapid sintering system is constructed. Basic data are collected relative to the tribology of the functionally inclined material, and it is proved that it is feasible to use the material for engine members. The process technology, assessment technology, and devices developed under this project are the first in the world, and are highly evaluated. (NEDO)

  4. Study on development of adsorbent of acetaldehyde; Acetaldehyde yo kyuchakuzai no kaihatsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Noda, T. [Nippon Steel Corp., Tokyo (Japan); Suzuki, M. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science

    1997-07-10

    The adsorption of acetaldehyde by porous ceramics impregnated with hydrazinium aluminum sulfate (HAS) is studied. Silicagel, activated alumina, activated clay, and activated carbon are compared, and it is found that silicagel and activated clay are suitable as a substrate for HAS impregnated adsorbent. The adsorption mechanism of acetaldehyde by the adsorbent is believed to be one in which acetaldehyde reacts with hydrazinium and yields acetaldazine. The adsorption capacity of the adsorbent at low acetaldehyde concentration of 0.1 ppm was as large as 1.36 mol/kg. This adsorption capacity at 0.1 ppm acetaldehyde concentration is remarkably larger than that of conventional activated carbon. Hydrazinium decomposes easily in the air because it is a strong reducing agent and reacts with oxygen or carbon dioxide. But hydrazinium impregnated on porous ceramics with HAS becomes more stable and maintains reactivity with acetaldehyde for longer than six months. An adsorbent made of porous ceramics impregnated with HAS is useful as a deodorant for acetaldehyde. 8 refs., 6 figs., 6 tabs.

  5. Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This report describes results of the study on the excess heat generation phenomenon during the electrolysis of heavy water using palladium metals as electrode in FY 1995. For the measurements of excess heat using an open type electrolysis cell during the excess heat generation demonstration model tests, significant excess heat beyond the range of input was not measured both for ICARUS-1 and for ICARUS-2. For the measurements using a fuel cell, high absorbing rate more than 0.85 was stably achieved for highly pure Pd electrode material by heat treatment and surface treatment. The excess heat could be reproduced for plural tests. The heat recovery rate more than 98% was obtained using the NHE type flow calorimetric system. The excess heat measurements using this are examined. For the reactive palladium materials, various materials ranging from single crystal to cold working polycrystal materials were systematically used for the absorbing experiments. Benchmark tests were also conducted through the cooperation with related researchers. 18 refs., 135 figs., 28 tabs.

  6. Current status and future of space development; Uchu kaihatsu no genjo to shorai

    Energy Technology Data Exchange (ETDEWEB)

    Matokawa, Y. [Institute of the Space and Astronautical Science, Tokyo (Japan)

    1998-05-01

    Space development has an aspect of contributing to livelihoods. Various types of satellites, such as those for weather forecasting, TV broadcasting, international communication (telephone and internet systems), and GPS-aided car navigation, have been already launched. Space science of the 20th century roughly tells the history of some 15 billion years from the big bang to birth of mankind as a spectacular story. The international space station, construction of which is to be started in 1998, should drastically enlarge man`s experiences in the universe. The space activity plans for the future draw various dreams, such as spaceplane, lunar base, solar generator satellite, Mars base, space colony, skyhook, and so on. Dreams of mankind have been eventually realized in the past history. It is time to deliberately assess what are meant by the space development of the 20th century, and to review ideal directions of the space development for the next 100 or 1000 years. 6 figs.

  7. FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis method of regular polymers with a 3-D structure was developed. Non-volatile dopants were developed, and structures of polymer-dopant composites could be controlled. In (2), precise control of conductivity was examined. Material processing and evaluation techniques were also examined through stabilization of polysilane thin films, optimization of pattern forming conditions, and precision of patterns. In (3), new silicon-based polymers have been synthesized. In (4), two kinds of polymers have been synthesized for development of materials with high photo-carrier generation efficiency and high mobility. 72 refs., 71 figs., 22 tabs.

  8. NEDO Forum 2000. Industrial technology development session; Sangyo gijutsu kenkyu kaihatsu session

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    This session presented the following subjects: I. IT innovation, II. Bio-seminar, III. Nano-technology, IV. Machine technology seminar, and V. 'Development subsidy project to put industrial technologies into practical use'. The theme in I relates to (1) influence of IT innovation on the society, (2) the theory of semiconductor evolution, (3) the theory of liquid crystal evolution, and (4) the theory of disk evolution. The theme II searches (1) how far have bio-technologies come?, (2) search of human evolution from genes, (3) can human being live up to 150 years by bio-technologies?, and (4) what is a DNA array (chip)?. The theme III covers (1) product innovation in polymers (new polymeric materials brought about by polymer nano-technology, taking polyolefin as an example), and (2) creation of ceramics materials by using nano-technologies. The theme IV relates to (1) ITS changes the car society into this way, (2) the current status and outlook on research and development of micro-machine technologies, and (3) the futuristic society and new industries opened by the Humanoid project. The theme V describes (1) practical application of ultra-small medical device production technologies, (2) development of next generation semiconductor manufacturing resists, (3) development for practical application of an optical brain function imaging device, and (4) development for practical application of new screening technologies toward creation of medicines using genome. (NEDO)

  9. Development of ultra-low pressure reverse osmosis membranes; Choteiatsu gyakushintomaku no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hirose, M.; Ito, H.; Ohara, T. [Nitto Denko Corp., Osaka (Japan)

    1998-06-05

    Described herein is development of ultra-low pressure reverse osmosis (RO) membranes. The composite RO membrane, which is now widely used, has a cross-sectional structure consisting of an ultrafilter membrane as the support and a very thin skin layer responsible for filtration. It is confirmed that the skin layer is of a pleated structure. Growing this structure can greatly accelerate permeation of water without damaging arresting and durability characteristics of the membrane, and hence is a desired approach. Utilization of molecular structure simulation of the skin layer materials is investigated by the molecular dynamics. The results show that the stable structure of the material for the skin layer in the RO membrane is a network structure with regularly arranged honeycombs, when it should arrest at least 99% of salt. These techniques serve as the bases for development of the ultra-low pressure RO membranes (ES Series), where the skin layer is made of cross-linked, totally aromatic polyamide. The membrane passes twice as large a quantity of water as the conventional one, is highly resistant to chemicals, and arrests 99.7% of salt. 3 refs., 4 figs.

  10. CAE for the development of two-wheeled vehicles. Nirinsha kaihatsu no tame no CAE

    Energy Technology Data Exchange (ETDEWEB)

    Hirose, T. (Suzuki Motor Co. Ltd., Shizuoka (Japan))

    1992-11-01

    Applications of CAE to the development of two-wheeled vehicles were outlined. The performance estimation program for 4-cycle engines featured by its easy execution was presented illustrating an estimation model and estimated results, and the FEM generator for strength/rigidity analysis CAE indicating analytical examples of a piston and frame which is featured by easy formation of models and easy execution of advanced analyses by beginners. The vibration analysis system to estimate exciting forces from engine specifications and to estimate vibration levels of bodies with FEM models was also presented together with the estimation system of rider's vibration sensitivity. Furthermore, the noise suppression/ exhaust pressure calculation program to support muffler designs by simultaneous calculation was presented together with the thermal flow analysis program featured by easy calculation with more suitable models illustrating the analytical example of thermal flow in a large luggage box. 7 refs., 15 figs.

  11. Development of lowdrag aerodynamically stable with indented processing; Indento kako wo hodokoshita seishin keburu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hojo, T.; Yamazaki, S.; Okada, H.

    1998-10-29

    A wind-resistant design of cables for large cable-stayed bridges is required as a measure against rain-wind induced vibration. In such bridges, many cables are arranged in a short pitch, which causes a large drag force on the cables. Therefore, reduction of drag force on cables is essential for rationalizing bridge design, as well as restraint of vibration. This paper describes studies on a new cable having both a low drag co-efficient force and rain-vibration suppressing effects. Through many investigations using wind tunnel tests, an indented cable was developed as a countermeasure against rain-wind induced vibration, and finally it was applied to the Tatara Bridge which is the largest cable-stayed bridge in the world. (author)

  12. Technical research and development of long-spanned bridges; Chodai kyoryo no gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sakai, F.; Yamanaka, M.; Ogawa, K.; Mizukami, Y.; Kano, J.; Watanabe, K. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1996-10-15

    Outlined herein is technical development of long-spanned bridges represented by suspension and cable-stayed bridges. The design of long-spanned bridges requires theoretical analysis of flexibility in which balance after they are deformed by load is taken into consideration. The matrix finite displacement analysis program is developed for optimizing cable-stayed bridge designs and determining suspension bridge shapes as the new major functions. The analysis program, named KASTAN, is also developed for stress analysis of the structure details. A wind tunnel for structure designs is installed to analyze resistance to wind. A number of experiments have been carried out by the tunnel for the designs of segment, main tower and overall bridge models. The means of controlling wind-caused vibration include hydraulic dampers, mass dampers, and combination of high damping rubber and spacer. Cable-stayed bridges are highly flexible, their types being selected by tower height and shape, span ratio and shape of the main beam, and cable position. These bridges constructed by the company include the S-shaped ones whose main beams are supported by cables suspended by two towers of different height, and the others with H-shape towers of high columns which are connected to each other by horizontal beams. 11 refs., 15 figs.

  13. Fiscal 1996 result reports of the researches under consignment from NEDO. Developments of fuel cell technology, polymer electrolyte fuel cell, fuel cell power generation system technology, and high-voltage type several tens kW class distributed power source system; Shin energy sangyo gijutsu sogo kaihatsu kiko itaku gyomu 1996 nendo seika hokokusho. Nenryo denchi gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, koden`atsugata suju kW kyu bunsan dengen system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper precisely reports the research result on development of fuel cell technology in fiscal 1996. On verification of cell durability, the cell test result in hydrogen including CO of 100ppm using Pt-Ru catalyst as CO resistant catalyst showed that the loss percent of cell voltage decreases with an increase in Ru content. On development of stack technology, the carbon humidification plate superior in chemical stability was developed as one of the parts for layered stacks. The separator with a water- permeable carbon plate and serpentine flow fields was fabricated for highly layered stacks, and achieved the target performance in single cell power generation test. On establishment of design basis for compact fuel processor, the bench-scale test was conducted of Ru/{gamma}-Al2O3 and Pt-Ru/{gamma}-Al2O3 catalysts as advanced CO selective oxidation catalyst for CO reducers. On demonstration test for the several tens kW class stationary power plant, the system configuration of power generation plants using natural gas as fuel was studied. 106 figs., 38 tabs.

  14. ¿Alcoholismo en Galicia: un camiño sen esperanza?

    OpenAIRE

    Folgar de la Calle, José María; Martín Sánchez, Rita

    2012-01-01

    O alcoholismo en Galicia é un mal endémico, polo que os enfermos non son considerados marxi­ nados. Os dous filmes que comentamos tentan chamar a atención e concienciar á sociedade sobre o carácter atípico deste problema.

  15. "It's not the size of the ship…"

    DEFF Research Database (Denmark)

    Christiansen, Ask Vest; Gleaves, John

    2013-01-01

    the challenge and reflected upon the conference theme "What do we (really) know about doping?" in their presentations. Not only as regards to the reliability of official statistics and the information that flows from organisations, NADOs and other stakeholders in sport, but also the more demanding task...

  16. Simulation of the Tornado Event of 22 March, 2013 over ...

    Indian Academy of Sciences (India)

    2013-03-22

    Mar 22, 2013 ... nagar and Akhaura upazila of Brahmanbaria district (DMIC 2013). Other damages of this tor- nado event were the damages and/or collapses of electric lines and poles, boundary wall, entrance gate, communication systems, breaking down of numerous trees, etc. The location of Brahmanbaria. (23.95.

  17. School Principals and Racism: Responding to Aveling

    Science.gov (United States)

    Charles, Claire; Mahoney, Caroline; Fox, Brandi; Halse, Christine

    2016-01-01

    This study responds to Nado Aveling's call in "Anti-racism in Schools: A question of leadership?" ("Discourse: Studies in the Cultural Politics of Education," 2007, 28(1), 69-85) for further investigation into racism in Australian schools. Aveling's interview study concluded that an overwhelming number of school principals…

  18. FY 1999 report on the survey of the overseas geological structure, etc. Japan-Indonesia joint Tanjung Enim coal exploration project; 1999 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Indonesia sekitan kyodo tansa Tanjung Enim project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper summed up the FY 1999 results of the survey conducted based on the agreement on the Tanjung Enim IV coal exploration project which was concluded between NEDO and Indonesia's Ministry of Mining Energy. The survey was made for an area of approximately 40km{sup 2} which is a north block of the south Arahan region, Tanjung Enim, South Sumatra, Indonesia. To grasp the succession of strata/rock facies/geological structure and the state of existence of the coal seams to be drilled, surveys were conducted on ground surface and boreholes. A total of 10 holes was test-drilled, and all the boreholes were physically logged. As a result of the survey, each of A1, A2, B, C and E coal seams was confirmed as main seams. A1, A2 and B seams are low in ash and sulfur contents with heating values of approximately 4,800 kcal/kg, C seam is high in sulfur content, and E seam is high in heating value, 6,000 kcal/kg. As coal seams for open pit mining, existence of A, B and C seams is expected which lay in the shallow part from ground surface to sea level of 0m and in the range of depth of approximately 100m. The proved coal reserves of these coals were estimated at 189 million tons. (NEDO)

  19. Fiscal 1997 report on the cooperative research on the preservation and sustainable utilization of biological diversification; Seibutsu tayosei hozen to jizokuteki riyo nado ni kansuru kenkyu kyoryoku (1997 nendo hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Cooperative researches were conducted between Japan and Thailand, Indonesia and Malaysia for the purpose of the technology development to make developing countries themselves preserve bioresources existing in tropical forests and use those sustainably. The research subjects for Thailand are a strategical study on eating of the primates, improvement of a microorganism culture collection system, preservation of biological diversification using an artificial ecosystem, bioresource utilization, etc. The subjects for Indonesia are a study of a microorganism culture collection system, study of plant preservation technology, study of microorganism utilization technology, study of plant utilization technology, promotion of the founding of the Indonesia tropical bioresource information center, etc. The subjects for Malaysia are biological diversification database and gene bank, assessment/monitoring of the ocean ecosystem, assessment and inventory of the ecosystem using hi-tech technology, search/separation of bioactive substances originated from microorganism/plant, etc. 26 refs., 24 figs., 81 tabs.

  20. Fiscal 1998 research report. Popularization project of the proper treatment technology of industrial wastes in Asian regions; 1998 nendo chosa hokokusho. Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Study was made on popularization of the proper treatment technology of industrial wastes in Asian regions. In principle, industrial wastes should be recycled in a country concerned, however, because of a difference in technology and industrial location, treatment of all industrial wastes in a country concerned is impossible. International cooperation is thus indispensable to promote proper efficient practical measures for environment. For studying the possibility of the international cooperation between Japan and Asian countries concerned for further recognition and solution of industrial waste problems, 'International Symposium on the Asian Industrial Waste Issue' have been held in Tokyo since 1997 for governmental staffs. In fiscal 1998, Malaysia was invited in addition to China, Philippines and Thailand for popularization of the proper treatment and recycling of industrial wastes in Asian regions. In every Asian countries, poor collection of discharge, treatment and disposal data is an obstacle to effective treatment. Technical cooperation and financial support by developed countries are demanded. (NEDO)

  1. Report for fiscal 1998 on industrial waste optimized treatment technologies dissemination and promotion business for asian region. Holding a symposium; 1998 nendo chosa hokokusho. Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo (symposium kaisai)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    An International Symposium on the Asian Industrial Waste Issue was held in Tokyo on 4 February 1999, where lectures were delivered by participants representing China, the Philippines, Thailand, Malaysia, and Japan. More 150 people attended the event, with questions and answered animatedly exchanged between the lecturers and the audience. The progress of urbanization is quite rapid in China, with the quantity of waste increasing every years to justify the anticipation that there will be a very sharp increase in refuse incineration in the near future. Raising a serious problem in China these days is the plastic waste. In the Philippines, there are no private-sector waste treatment/disposal facilities and corporations are not obliged to take care of their waste. Consequently, very little treatment or recycling is being undertaken. In Thailand, although waste treatment/disposal centers are in operation financed by the Government and private sectors, the cost is very high, and the Government policy is that private investment will be encouraged and supported in future. In Malaysia, privatization is in progress of the business of managing waste in the solidified form. A comprehensive waste treatment/disposal plant was completed in 1998 by the endeavors of a Denmark-Malaysia consortium, and is in operation since then. (NEDO)

  2. Basic investigation on promotion of joint implementation in fiscal 2000. Survey on energy saving and CO2 emission reduction in Cilacap Refinery; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Cilacap seiyusho ni okeru shoene CO2 sakugen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of saving energy and reducing greenhouse gas emission, a basic survey has been performed on the atmospheric crude oil distillation units and the high vacuum distillation units at Cilacap Refinery in Indonesia. The first site survey in September 2000 has carried out a survey on the situation of the facilities and operation upon obtaining the facility data and operation information from Pertamina. As a result, it was revealed that there is a room of improvement in the heat recovery, whereas a modification design was executed on the improvement proposals on the heat exchanger system. However, the second site survey in November 2000 has revealed that Pertamina had executed in 1998 through 1999 the de-bottlenecking project on the crude oil atmospheric distillation units (two units) and the high vacuum distillation units (two units), by which the capability has been expanded, and the heat recovery rate has been increased. It is not possible to look for extremely large enhancement of the heat recovery rate beyond that point, and the reduction of CO2 emission would also be small. As a result of discussions, the present project was found capable of reducing annually the CO2 emission by 36,500 tons. (NEDO)

  3. FY 1998 report on the results of R and D projects by local consortiums for immediate effects. Development of woody ceramics and application to building parts; 1998 nendo woody ceramics no sosei to kenchiku buzai nado eno oyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D project has been implemented for developing materials for, e.g., light, highly heat-insulating and energy-saving type building parts (e.g., roofing tiles and tiles), and light tableware having warmness of wood. The stock materials for china and porcelain, roofing tile clay, tiles and cement are dispersed with hollow microcapsules as the filler, which are of glassy balloons thermally treated to be highly functional, in order to develop superlight, highly heat insulating and high-strength materials. For development of the woody ceramic materials, the microcapsules are investigated for size, thickness, thermal shrinkage, fusibility, compressive stress, reinforcing mechanisms, and monodispersibility. Also investigated are optimization of material formability, development of commercial ceramics and evaluation of their marketability, decoration techniques, antimicrobial membrane materials and their immobilization techniques, development of antimicrobial ceramic tiles, evaluation of the antimicrobial membranes, evaluation of resistance to microwaves, and so on. The efforts are also directed to researches on fundamental techniques for woody tile clay, and R and D of the application techniques and products of the woody cement. (NEDO)

  4. Report for fiscal 1994 on commissioned operation for research cooperation related to simplified purification system for industrial waste water; 1994 nendo sangyo haisui nado no kan'i joka system ni kansuru kenkyu kyoryoku hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    With an objective to serve for environmental preservation in developing countries, joint researches have been performed on anaerobic waste water treatment systems utilizing bio-technology. This paper summarizes the achievements in fiscal 1994. In the research cooperation with Thailand, a reactor applicability test was performed by using a pilot plant to determine the operating conditions, and necessary data were obtained. The pilot plant was completed of installation in November. In the research cooperation with Indonesia, Tofu manufacturing waste water was selected as the object of pilot plant research. In the detailed design the Tofu manufacturing waste water shall be treated anaerobically, and the kitchen waste water shall be treated aerobically to acquire the intended water quality. In the research cooperation with Malaysia, as a result of visiting six industries and 22 factories for investigation, waste waters from chemical and foodstuff factories were selected as the object waste waters for the research. Three researchers from Thailand and Indonesia respectively were received in Japan to provide education including experimental training and visits to waste water treatment facilities. (NEDO)

  5. Basic investigation on promotion of joint implementation in fiscal 2000. Efficiency improvement and energy conservation at Uong Bi power plant; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Uong Bi hatsudensho no koritsuka to sho energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Discussions have been given on energy conservation, and reduction in greenhouse gas emission through efficiency improvement at the Uong Bi coal burning power plant in Vietnam. The Uong Bi power plant, which has become using coal of lower quality than the design value, has had incomplete combustion, resulting in increase of unburned components in ash, and decrease of the boiler efficiency to 65 to 70%. Clinker hopper troubles have been occurring frequently, causing plant shutdown at a number of times. The turbine efficiency also shows as very low value as 26 to 27%. The plan has envisaged replacement of combustion parts of the boilers, withdrawal and replacement of the turbine generation systems, new installation of electric dust collectors, modification of the ash treatment system, additional installation of the re-circulation system, new installation of waste water treatment facilities, and modification of the waste water treatment equipment in the plant premises. As a result of the discussions, the annual energy saving quantity was found to be 62,936 tons of crude oil equivalent for the case where only one turbine is renewed, and 93,298 tons for the case where both of the two turbines are renewed. The annual reduction quantity of the greenhouse gas emission was found to be 251,215 tons and 372,402 t-CO2, respectively. (NEDO)

  6. FY 2000 survey of the geological structure overseas, etc. Japan-China joint coal exploration - Yu Xian project; 2000 nendo kaigai chishitsu kozo nado chosa - futai shiryoshu. Nippon Chugoku sekitan kyodo tansa Yu Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This data book summarized the proceedings and the technical report of the management committee on the Japan-China geological structure survey based on the consultation concluded between NEDO and China's bureau of coal field geology and a report meeting on the Yu Xian project. In the exploration, conducted were the boring survey of 10 boreholes, seismic survey of 2D (71 traverse lines, 180.105km) and 3D (1.5km{sup 2}), VSP (6 holes (345 shots)) and the low velocity band survey (2,072 shots). The geological structure of the area presented the syncline structure with a gentle line associated with foldings and a number of faults and was classified into the medium class or the class of a little complication in the Chinese standard. The number of the faults confirmed in this exploration totaled 57. Coal reserves by coal seam were 157.22 million tons at No. 5 seam and 102.57 million tons at No. 1 seam. The total amount of the two seams was 79.1% of the total coal amount in all area. The coal quality of Nos. 1 and 5 was brown coal - flame coal in the Chinese classification, and subbituminous coal B - subbituminous coal C in the ASTM classification. The coal, however, cannot be used for process raw coal. There is a technical potentiality of the fixed bed pressurized gasification. (NEDO)

  7. Fiscal 2000 survey report. On-site survey of local state of affairs such as energy efficiency enhancement (Mongolia); 2000 nendo energy shohi koritsuka nado chiiki josei genchi chosa hokokusho. Mongoru

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Information was collected and surveys were conducted in Mongolia in an effort to acquire information necessary for energy related technical cooperation. The results were arranged in four fields which are (1) the current state of economy and the future trend, (2) current state of energy production/consumption and the future trend, (3) current state of power supply/demand and power facilities and the future trend, and (4) the current state of energy efficiency enhancement and the future trend. Mongolia has a population of 2.45 million at a density of 1.57/km{sup 2}, with Ulan Bator the capital inhabited by 0.69-million people. The mean air temperature is -10 degrees C in the period November through March, which makes heating indispensable. Power stations are of the heat and power cogeneration type. Power is supplied by the Eastern, Central, and Western systems, with the Central system producing 80% or more and independent power sources 10%. Its economy has already recovered from the confusion that followed the change of its national constitution. Mongolia's demand for power lingers low, however, and its facilities can produce more electricity than what is now wanted. Energy efficiency enhancing activities should start with the upgrading, reinforcement, and maintenance of the existing facilities and with independent power sources. (NEDO)

  8. New energy vision for Ginoza village. Fiscal 2000 survey report on new energy vision formulation project for Ginoza village; Ginozason shin energy vision. 2000 nendo Ginozason shin energy vision sakutei nado jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A new energy vision has been formulated for Ginoza village, Okinawa Prefecture, for the realization of symbiosis with nature. It is a 5,000-strong entirely farming village situated along the eastern coast at the middle of the main island of the Ryukyus, with energy consumption of 9,982 kl in terms of crude oil in fiscal 1999. The results of activities in this connection are summarized in six chapters, which are (1) the state of the village and new energy, (2) current state of energy supply/demand and outlook for the future, (3) existing amount of new energy, (4) trends of types of new energy under study, (5) feasibility of new energy introduction, and (6) Ginoza village's new energy vision. Chapter (6) is constituted of the general principles of new energy introduction into Ginoza village and a long-term vision of new energy introduction for each field, and discusses the introducible types which are photovoltaic power generation, wind power generation, small scale hybrid power source systems, fuel cells, natural gas fired cogeneration, refuse fueled power generation, and clean energy vehicles. (NEDO)

  9. FY 1999 research cooperation project - the research cooperation on the protection of biodiversity and sustainable use, etc. Follow-up; 1999 nendo seibutsu tayosei hozen to jizokuteki riyo nado ni kansuru kenkyu kyoryoku. Follow up

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The follow-up for the research cooperation for Indonesia, Malaysia and Thailand was conducted to make it possible that developing countries themselves protect biological resources in the tropical area, etc. and make the sustainable use of biological resources using bio-technology. In Indonesia, the follow-up was to be made for proceeding with the joint study for 'The study on the plant utilization technology - search for useful plant ingredients' reported by Professor Koshimizu, Kinki University. In Malaysia, considering that equipment is enough installed there and research leaders are very excellent, it is considered that the country is suitable for the partner of future joint research on microorganisms with Japan. Moreover, the merit in joint study is the cooperation in study of information system and culture collection. In Thailand, Japan told them that the study theme has to be made smaller toward the culture collection rich in content and the search for useful plants/bacteria. (NEDO)

  10. Research report for fiscal 1998. Basic research for the promotion of joint implementation etc. (Ryazanskaya thermal power station modification program); 1998 nendo kyodo jisshi nado suishin kiso chosa Ryazanskaya karyoku hatsudensho kaishu keikaku chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Under study is the modification of the four antiquated 300MW brown coal-fired power plants of the Ryanzanskaya thermal power station. Under the modification program, the plants will be burning a mixture of 60% coal and 40% natural gas for an increase in efficiency and for a great decrease in greenhouse gas emission. The amount of greenhouse gas emission of 6,858,592 tons/year before the modification will be reduced by 19.4% to 5,532,198 ton/year. The budget for the modification will call for 719,731,700 US dollars. EIRR (economical internal rate of return) is calculated based on the figures provided by the Russian office concerned about the current fuel cost and the current rates for the supply of electricity and heat. It is found that EIRR fluctuates depending on the ruble/dollar exchange rate. Although it does not pay at the current exchange rate, yet, when a US dollar is worth 13.0 rubles, an EIRR of 15% will realize at an availability factor of 70%. The same result is obtained when the availability factor is 80% and a US dollar is worth 14.8 rubles. There is a plan to fire the plants with 100% natural gas in the future. If the plan is implemented, a modification to incorporate gas turbine combined cycle will become feasible. (NEDO)

  11. Report on the site surveys in fiscal 1999 on the regional situations such as energy consumption efficiency improvement. The north-western part of China; 1999 nendo energy shohi koritsuka nado chiiki josei genchi chosa hokokusho. Chugoku seihokubu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper reports the site surveys in fiscal 1999 on the energy consumption efficiency improvement in the north-western part of China. Although blessed with affluent natural resources, the regional development is delayed because of geographical restrictions and harsh climate conditions. Power generation facilities include hydroelectric power plants with output of 7.81 million kW, thermal power plants with 13.89 million kW, and power wind power plants with 70 thousand kW. The demand is estimated to increase by 4.6% annually in average. Thermal power plants are those made by the former Soviet Union, having poor power generation efficiency, which is scheduled to be improved by facility modification. Automation is also behind the times. These situations have brought about low reliability, delay in building electric power network in agricultural districts, and transmission wire loss (reducing 8.1% loss to 6% is planned). The electric power charge systems also have various problems. Environmental measures are also an issue. Dissolution of energy shortage as a result of developing the north-western area can be said a key to the future development of China. Xinjiang Electric Power Company is considering wind power generation as the center of new energy utilization. Representative facilities utilize affluent wind power available in the topography of the Tenzan mountain range in the suburb of Urumqi, the facilities being made of Denmark. Photovoltaic power generation is exiguous in realizability for the time being in terms of cost. Expectation is placed on fuel cells. (NEDO)

  12. Fiscal 1999 international energy conservation model project. Report on result of demonstrative research concerning cement clinker cooling system; 1999 nendo kokusai energy shohi koritsuka nado model jigyo seika hokokusho. Cement clinker reikyaku sochi ni kakawaru jissho kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing energy consumption and CO2 discharge in a cement plant in Indonesia, R and D was conducted on new clinker cooling system, high performance kiln combustion system, and technology for steady kiln operation and control, with the fiscal 1999 results reported. In the research on the optimum clinker cooling system, a new type clinker cooling system (CCS) was developed in which air beams are applied only to stationary grate rows, in an air beam type clinker cooling system where cooling air is fed to each block, with grate plates used as the air duct. This year, in an actual machine testing equipment (capacity 2,500 t/d), the whole heat recuperation area was modified for the CCS, with the operation started since February, 1999, aiming at the optimal clinker cooling effect and high heat recovery efficiency. The heat quantity for the entire system showed a decrease of 60 kcal/kg in the heat consumption rate through CCS modification, kiln burner adjustment, etc. So long as the demonstration plant is concerned, design of a new type burner and study/design for the kiln stabilization were nearly completed. (NEDO)

  13. Basic investigation on promotion of joint implementation in fiscal 2000. Energy conservation and modernization plan for Chhatak Cement Co., Ltd.; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Chhatak Cement sha shoene, kindaika keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of saving energies and reducing greenhouse gas emission, discussions were given on a modernization plan for the Chhatak cement factory in The People's Republic of Bangladesh. The Chhatak cement factory having a nominal production capability of 267,000 tons a year uses mainly wet-type long kilns of old type, consuming a great amount of natural gas. The present plan has discussed adoption of the Japanese energy saving technologies. The technologies use a vertical roller mill for raw material pulverization, a suspension preheater and a short kiln for clinker sintering, a grate cooler for clinker cooling, and the pre-crushing system. The result of the discussions provided the prospects of reduction in the natural gas consumption at 50%, and reduction of electric power consumption at 16%. This will mean the annual reduction of about 22,000 tons as converted to crude oil. The CO2 reduction amount would reach 51,800 tons a year. The total investment amount would be US$37,327,000. The result of the financial analysis according to the case studies appears severe, wherein reduction of the various expenses is desired possibly by the finance from Japan with generous conditions.(NEDO)

  14. Report on investigations in fiscal 2000 on the basic investigation on promotion of joint implementation. Effective utilization of associated gas as CNG; 2000 nendo kyodo jisshi nado kiso chosa hokokusho. Zuihan gas no CNG to shite no yuko riyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The Back Ho oilfield is the largest oilfield in Vietnam and at the same time is producing the largest amount of natural gas (associated gas) in Vietnam. Although the majority of the associated gas has been used in the power generation plant, a large amount of surplus gas is not effectively used because of shortage of fund and technologies. Accordingly, a feasibility study has been executed for a project to compress 20% of the associated gas into CNG, and use it effectively as automobile and factory fuel. As a result of the site survey, it was found that, although Vietnam consumes less amount of energy and emits less amount of CO2, the nation has a strong interest and a large amount of knowledge about global warming and CDM because the country is subjected to large effect of warming. Furthermore, it has been reconfirmed that introducing CNG into this territory is highly effective. Discussions have been made on places of installing the facilities, effective surplus gas utilization systems, facility specifications, utilities, and number of workers. Calculations were made on approximate cost of the facilities and the running cost. As a result of the surveys and discussions, it was determined that technological support from Japan and the Yen loan for environment with low interest rate are necessary. (NEDO)

  15. Basic investigation project for energy consumption efficiency improvement in developing countries. Invitation of engineers from developing countries (Vietnam, Philippines, and India); Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo. Hatten tojokoku gijutsusha shohei jigyo (Betonamu, Philippines, Indo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The International Center of Environmental Technology Transfer has invited seven engineers from Vietnam, eight from Philippines and two from India for human resource education project for environmental preservation in developing countries. Those who were invited are administrative officials and engineers who work at administrative agents, research institutes and corporations related to energy conservation and environment preservation. In this invitation program, lecturers were invited from governmental offices, universities and corporations according to their expertise fields to carry out lectures and site training. With respect to energy conservation, lectures were given on a `summary of energy saving methods` by a lecturer invited from the Chubu Governmental Department of Trade and Industry, and on an `introduction to new energies` by Prof. Shimizu at the Engineering Faculty of the Mie University. Both lecturers emphasized the necessity of energy conservation, and importance of new energies as clean energies. The trainees showed strong interest when they visited a `cement factory` and a `coal burning thermal power plant` as the key industries. Their experience would be reflected strongly on guiding operations of factories in their own countries. 56 figs., 15 tabs.

  16. FY 2000 report on the basic survey to promote the joint implementation. Conversion of raw materials in fertilizer plants and energy conservation in India; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Indo hiryo plant genryo tenkan to shoene

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As a project contributing to reduction in greenhouse effect gas emissions by introducing energy conservation technology of Japan to India and to sustainable economic development in India, study of 'conversion of raw materials in fertilizer plants in India' was made, and the results were reported. The Indian government has been controlling the retail price of fertilizer by the subsidy policy for the protection of the domestic fertilizer production. Therefore, plants, which use coal/heavy oil/naphtha with much greenhouse gas emission as raw materials, have been behind improvement and now have no competitive force in the international market. In this project, concerning ZIL's fertilizer plant, the ammonia production capacity was set at 750 t/d and the urea production capacity at 1,300 t/d, and the energy conservation technology and the conversion of raw materials from naphtha to natural gas were studied. As a result, the amount of energy conservation was 55,705 toe/y, and the amount of CO2 reduction was 245,139 t-CO2/y. Further, this project indicated that profits were expected to increase and the cash flow would change for the better. (NEDO)

  17. Basic project on the cooperation in enhancement of the international energy consumption efficiency. Survey of energy conservation potential by industry; 2000 nendo kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo hokokusho. Gyoshubetsu sho energy potential chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of looking for measures to promote the effective energy conservation in China, the potential energy conservation amount in general plants was surveyed and analyzed by industry. Activities were made in the following fields: 1) survey of the actual state of energy in main industries; 2) energy conservation potential in the cement industry in China; 3) energy conservation potential in thermal power plants in China. In 1), survey was made on 8 industries including the iron/steel industry and oil refining industry. In 2), survey was made of the actual state of the Liulihe cement plant and Shitou cement plant. The subjects extracted were the arrangement of instrumentation equipment such as the exhaust gas analyzer needed for combustion management, improvement of the air/fuel ratio of kiln, enhancement of cooling efficiency of clinker cooler, etc. In 3), the actual state of the Qinling power plant was surveyed, and it was made clear that high efficiency of 38% or more can be maintained if the appropriate use/maintenance management is made (coal unit consumption: 383g/kWh in Qinling and 309g/kWh). (NEDO)

  18. Report on the FY 1992 basic survey for industrialization related to the survey of overseas geological structure (Embalut West area, Indonesia); 1996 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa hokokusho (Indonesia Embalut nishi chiku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    The paper reported the FY 1992 basic survey for the coal mine development/industrialization in the Embalut West area of Indonesia. The geological structure in the survey area is under the Loa Haur Syncline which lies approximately north and south to the west of the area, and is regarded as the stabilized structure having no faults. The three beams from the upper part, S14, S13 and S12, are assumed to be the coal seams to be drilled. The average seam thickness is 1.17, 2.35 and 3.09m, respectively, and the continuity is good. In S14 beam, which is thin, it is difficult to mine coal using equipment. The theoretical minable reserve of the three coal seams is 18,859,000 tons. The recoverable coal reserve is 12,258,000 tons at a mining recovery of 65%. In case of annual production of 0.4 million tons, it is possible to mine more than 30 years. The coal is classified into a subbituminous coal-brown coal rank of the JIS coal classification. It is high in water content and medium in heating value, but is an environmental protection type with low ash and low sulfur content. In the case of mines in the Mahakam River basin, barge transport is indispensable. For sea transportation, the following should be studied in the light of the international price competition: reinforcement of shipping facilities on Mahakam River, increase in barge size, joint use of Balikpapan Coal Center, etc. (NEDO)

  19. FY 2000 report on the basic survey to promote Joint Implementation, etc. Survey on the energy conservation of the Lianyuan Iron and Steel Group Complex, China; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Lianyuan tekko sho energy chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of conserving energy and reducing greenhouse effect gas emission, a feasibility study was carried out of the installation of energy conservation facilities at the steelworks of Lianyuan Iron and Steel Group Complex, Loudi City, Hunan Province, China. The installation of the following facilities was studied: coke dry quenching (CDQ) equipment, coal moisture control (CMC) equipment, sintering ignition furnace equipment, cooler exhaust heat recovery equipment, top pressure recovery turbine (TRT), and hot stove exhaust heat recovery equipment. As a result of the study, the energy conservation amount was 20,000 toe/y by CDQ, 2,530 toe/y by CMC, 900 toe/y by improvement of ignition furnace in the sintering process, 12,300 toe/y by sintering cooler, 13,200 toe/y by TRT, and 10,300 toe/y by hot stove exhaust heat recovery equipment. Further, the amount of greenhouse effect gas reduction was 61,022 t-CO2/y, 7,843 t-CO2/y, 2,896 t-CO2/y, 38,060 t-CO2/y, 55,295 t-CO2/y, and 40,621 t-CO2/y, respectively. In the estimation of effects vs. expenses, the sintering ignition furnace, sintering cooler exhaust heat recovery, and hot stove exhaust heat recovery indicated the comparatively favorable values. (NEDO)

  20. Fiscal 2000 survey report. Basic survey of promotion of joint implementation, etc. Rehabilitation of KESC gas turbine power plant; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. KESC/gas turbine hatsudensho rihabiri

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    KESC (Karachi Electric Power Supply Corporation) facilities supplying electricity to Karachi, Pakistan, were examined for rehabilitation aiming at energy conservation and greenhouse gas reduction. The rehabilitation program covered power generation facilities, fuel supply facilities, instrument control systems, and their layout. Discussed were a schedule for the production, transportation, and installation of facilities, sharing of burdens between KESC and Japan, and the economic and environmental merits expected to ensue from energy conservation and greenhouse gas reduction. The results are mentioned below. Project implementation will take approximately 18 months, and Japan will be responsible only for dispatching specialists to elaborate on CDM (clean development mechanism) and engineers. In Case 1, the amount of initial investment is estimated at 84-million US dollars, the economical efficiency of energy conservation at 107t/year/million yen, and the economical efficiency of greenhouse gas reduction at 330t-CO2/year/million yen. It is found in the study of profitability that the loan will be collected in 10 years after project implementation and the initial investment in 22 years. (NEDO)

  1. Report for fiscal 1998 on basic commercialization survey related to geological structure surveys in overseas countries (Manguerra, the Philippines); 1998 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Philippines Manguerra) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Commercialization survey was performed on the mines in the Manguerra district in the Philippines by means of geological structure surveys. The site surveys included geological and test drilling surveys, and those on conditions for developing underground mining mines, and infrastructures. The geological survey area spread out about 5 km{sup 2}, two test wells were drilled (to depths of 330 m and 290 m), trench survey was performed on 58 locations, and coal sample collection and analysis were carried out on eight locations. Furthermore, surveys were extended to the Manguerra mine operating status, on-the-ground facilities, roads for transportation, marketing, and related laws and regulations. As a result of the surveys, the Manguerra district was suggested of frequent sea water inundation into the coal field, leading to a view that the district is unstable from the viewpoint of development of coal beds. However, samples collected from the existing mining area indicated to have less water content and ash and high calorific power. The coal has high product value. The result of coal quantity calculation indicated 320122 tons as the total of defined and estimated quantity. The great depth mining plan was prepared from the viewpoints of actual yield, productivity, safety aspects, technological enhancement, and suppression of additional investments to minimum. (NEDO)

  2. Basic investigation on promotion of joint implementation in fiscal 2000. Modernization project for North Bangkok Thermal Power Plant in Thailand; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Tai North Bangkok karyoku hatsusensho kindaika jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of saving energy and reducing greenhouse gas emission, a modernization project has been discussed on the North Bangkok heavy oil burning thermal power plant owned by Electricity Generating Authority of Thailand (EGAT). The present project plans to withdraw the existing units No. 1, 2 and 3, and install two new generating facilities with the rated output of 358.3 MW using natural gas as fuel. The present feasibility survey has performed detailed comparative discussions on four cases, whereas a proposal was selected to withdraw all of the boilers, steam turbines, and generators, and install two single axis combined cycle systems whose output has been increased by using the existing fuel tank area. The energy saving effect by this project can reduce fuel consumption annually by 514 kt of crude oil equivalent. The greenhouse gas can be reduced annually by 2,680 kt-CO2. The project will require a total fund of about 57 billion yen. The profitability assessment calls for the internal profitability of 8.413% and the investment fund efficiency of 1.69%. The economic investment payback effect of this project is determined sufficient. (NEDO)

  3. Survey report on project for drawing district energy-saving visions for Town of Aizu Wakamatsu. Preliminary survey; 2000 nendo Aizu Wakamatsu shi chiiki sho energy vision sakutei nado jigyo (shoki dankai chosa) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    The feasibility study is conducted for introduction of the district energy-saving measures in City of Aizu Wakamatsu, for which the actual situations of energy consumption and promising energy-saving measures are surveyed. The city has a typical basinal weather, cold in winter and very hot and humid in summer, and tends to have a longer air-condition period in a year. It is considered that there are many wasteful energy consumption items to be studied for reduction. In the area of moving means, dependence on public transportation systems is considered to be relatively low, suggesting that there are much space of reducing transportation energy by the measures such as self-imposed control on use of private cars, promotion of utilizing public transportation systems and fuel-saving type driving throughout the city. The promising energy-saving measures studied to verify the effects include introduction of PVM analyzers for establishing better cost/effect relationship between power consumed by air-conditioners and pleasantness; introduction of garbage power generation, co-generation and high-efficiency illuminators; improvement of power-factor; and demand control for air conditioning, rationalization of power-receiving facilities, introduction of systems for saving flushing water and improvement of air conditioners' outdoor facilities. (NEDO)

  4. New energy vision for Nomura town. Fiscal 2000 survey report on regional new energy vision formulation project for Nomura town, Ehime Prefecture; Nomuracho shin energy vision. 2000 nendo Nomuracho chiiki shin energy vision sakutei nado jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    An effort is being exerted to build a town which will generate but a little environmental impact, with symbiosis with nature established as the highest priority target of the town administrative activities. Under the Nomura town new energy vision, a basic policy and measures are established toward the promotion of new energy introduction, with local features, existence of new energy resources, and the feasibility of new energy adoption taken into consideration. Surveys were made and the results are compiled into seven chapters, which involve (1) the trend of new energy, (2) local features, (3) existing amount and available amount of new energy, (4) basic policy toward the introduction of new energy, (5) main projects for the introduction of new energy, (6) details of the basic policy toward the introduction of new energy, and (7) the Nomura Town Deliberation Committee on New Energy Vision Formulation. Chapter (6) covers the assessment of new energy introduction feasibility, promotion of concretized introduction projects, public relations/enlightening/popularizing activities, and assistance for new energy introduction. Studied for introduction are photovoltaic power generation, solar heat utilization, wind power generation, biomass power generation, and the like. (NEDO)

  5. Fiscal 2000 report of investigation. Project for promoting international cooperation for global environment/Project for assessment on effect of climate change; 2000 nendo chikyu kankyo kokusai kyoryoku suishin jigyo / kiko hendo eikyo hyoka nado jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Assessment and examination were conducted on the scientific/technological aspect, environmental aspect and economic/social aspect concerning measures for mitigating climate change, as a part of international cooperation in global warming issues. In the development of assessment methods for cost analysis, it revealed that, in the activities for mitigating emission of greenhouse effect gases (GHG) or for increasing carbon sequestration, benefits of the mitigation sometimes surpassed their cost, allowing the society to benefit from the mitigation. In the examination of problems in technology transfer and their solutions, it was found that, in order to attain successful transfer, partnership among the parties interested was essential and that each government was capable of promoting such partnership. In the assessment of various policy options, the situation in the U.S. is such that the market aspect of GHG emission permit and credit trading is rather weak because of immaturity in a legal framework on GHG emission trading and because of undefinedness in the systems of the Kyoto Protocol and in the possibility of its validation. However, the reason enterprises are actively participating in the early market is that they plan a risk-hedge for example in anticipation of tighter regulations in the future. (NEDO)

  6. 1998 Annual Study Report. Surveys on seeds for global environmental technologies, including those for energy saving; 1998 nendo chosa hokokusho. Sho energy nado chikyu kankyo taisaku gijutsu no seeds ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The energy-saving and other global environmental technologies are surveyed by collecting relevant information from various institutes, both abroad and domestic, to contribute to development of ceramic gas turbines. USA has announced a climate change plan, based on the five principles, to promote utilization of high-efficiency technologies and development of new clean technologies. UK is promoting to improve energy efficiency, along with liberalization of its energy markets. Germany concentrates its efforts in the 'Program for Energy Research and Energy Technologies.' France places emphasis on prevention of air pollution and rational use of energy. The R and D trends at public institutes, e.g., universities, for global environmental technologies are surveyed, from which a total of 14 themes are extracted as the seed technologies. At the same time, a total of 9 techniques potentially applicable to the seeds are extracted by mainly reviewing JICST and patent information, and assessed. The R&D trends of the IPCC-related researchers are also surveyed, but provide no theme directly applicable to the seeds. Most of the related themes at the private and public institutes surveyed, both domestic and abroad, are concentrated on carbon dioxide. (NEDO)

  7. Fiscal 1999 survey report. Project of promoting international cooperation on global environments/Project of assessing climate change impacts; 1999 nendo chikyu kankyo kokusai kyoryoku suishin jigyo chosa hokokusho. Kiko hendo eikyo hyoka nado jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    As part of international cooperation concerning global warming, an assessment is conducted of climate change mitigating measures, from the viewpoints of technology, environment, economy, and community, in coordination with the IPCC (Intergovernmental Panel on Climate Change) 3rd working group responsible for energy policy and technological development. It aims to contribute to the preparation of a 3rd assessment report, and covers (1) the development of an assessment technique relating to cost analysis, (2) problems in the transfer of technology and solutions for them, and (3) the assessment of various policy options. Under item (1), studies are made about modelling techniques, common parameters and their values, potentials for effect, control of warming, etc. Under item (2), factors impeding the transfer and diffusion of technology are extracted and solutions therefor and the establishment of new incentives are deliberated, with analysis and investigation focused on tasks and solutions for furthering global transfer of technology with attention paid to various specific cases. Under item (3), concrete and feasible policy options are discussed on the basis of the outcome of the above-named endeavors, in view of characteristics of each of the regions, departments, and techniques. (NEDO)

  8. Fiscal 1999 research report. Survey on development trends of natural gas conversion technologies into liquefied fuel in Russia; 1999 nendo Roshia ni okeru tennen gas no ekitai nenryoka gijutsu no kaihtsu doko nado ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Russia having world-largest natural gas resources is promoting the forefront basic research on liquefaction technology of natural gas, in particular, Fischer-Tropsch (FT) synthetic process positively. For 3 years from fiscal 1998, this project surveys the trend of R and D on catalytic technology for liquefaction of natural gas in Russia, and fabricates the prototype FT catalyst effective for liquefaction of natural gas at a Russian research institute to evaluate its practical applicability experimentally. In fiscal 1999, based on the research result in fiscal 1998, the project carried out continuous survey on the research activity of research institutes in Russia, the research trend of liquefaction technology and the concrete results of contract researches on catalyst, and summarized the evaluation result of research results. In addition, continuous world-wide document survey on FT synthetic process was made to confirm R and D trends based on the trend of liquefaction research projects in the world, and to collect basic information on catalytic reactors for FT synthetic process by document survey. (NEDO)

  9. FY 2000 report on the basic survey to promote Joint Implementation, etc. Project for the modernization of the Tashkent cogeneration plant; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Tashkent netsuheikyu hatsudensho kindaika keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigational study was carried out of the project for energy conservation and greenhouse effect gas emission reduction by introducing the newest and most powerful gas turbine cogeneration facilities to the Tashkent cogeneration plant in Uzbekistan. At the Tashkent cogeneration plant, each of the facilities is being superannuated, which leads to lowering of operational reliability and increase in cost of repairs. In the project, studied was the introduction of the newest and most powerful gas turbine cogeneration facilities with heat output of 100 Gcal/h equivalent to that of one can of the existing hot water boiler and with generated output of 80MW. As a result of the study, obtained were the energy conservation amount of 83.9 ktoe/y and the greenhouse effect gas reduction amount of 179.7 kt-CO2/y. The initial investment amount was 10.003 billion yen. Expenses vs. effects were 8.39 toe/y-million yen in energy conservation amount and 18.0 t-CO2/y-million yen in greenhouse effect gas reduction amount. In the study of profitability, the internal earning rate was 9.24% after tax, the return yield of capital was 41.26%, and the period of ROI was 16.9 years. (NEDO)

  10. FY 1999 Report on overseas geological structure surveys. Joint Japan-China Yu Xian exploitation project (Attachments); 1999 nendo kaigai chishitsu kozo nado chosa futai shiryo. Nippon Chugoku sekitan kyodo tansa Yu Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This reports provides the attachments for the report JN0041264. The contents include (1) minutes of the fourth steering committee, (2) technical reports presented to the fourth steering committee (I: report on FY 1998 joint exploitation works, and II: report on FY 1999 joint exploitation works), (3) minutes of the fifth steering committee, and (4) technical reports presented to the fifth steering committee (I: report on FY 1999 joint exploitation works, and II: report on planned FY 2000 joint exploitation works). The item (1) includes approval of the reports on FY 1998 and 1999 joint exploitation works. The item (2)-I report includes seismic exploitation test works, observation work results and quality evaluation thereof; drilling exploitation work results, quality evaluation thereof, exploitation results and evaluation thereof; exploitation results and evaluation thereof; and proposals. The item (2)-II report includes seismic exploitation, drilling exploitation, and man-hours of the workers from the both countries. The item (3) includes approval of the reports on FY 1999 joint exploitation works and planned FY 2000 joint exploitation works. The (4)-I report includes seismic exploitation work results and evaluation thereof, seismic exploitation test works, drilling exploitation work results, quality evaluation thereof, exploitation results and evaluation thereof, and proposals for the future works. The (4)-II report includes seismic and drilling exploitation plans, and numbers and periods of the workers from the both countries. (NEDO)

  11. Report on the FY 1993 basic survey for industrialization related to the survey of overseas geological structure (Tebulan East area, Malaysia); 1993 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Malaysia Tebulan higashi chiku) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The survey was conducted based on 'Scope of work for detailed coal exploration in the Tebulan East block of the Merit Pila coal field, Sarawak, Malaysia' concluded on June 19, 1993 between NEDO and Global Mineral which owns the mining right. The field survey was for the geological survey, survey of conditions of open pit mining, and infrastructure survey. The confirmed/estimated coal amount totaled 22,65 million tons in 4 coal seams. The all sulfur content is low, approximately 0.12%. The heating value is 5,820 kcal/kg. As to the infrastructure, various conditions are good for transportation, shipping facilities, etc. from mine site to truck transport/barge transport/external route shipping. The drilling was planned to be made by open pit mining by the truck and shovel system, and the scale of the planned production was 0.3 million tons. The ash is low in amount, and there was no coal preparation. Clean coal is produced by crushing, sieving and washing. Attached were the borehole log (JN9940782), route map, and trench sketch (JN9940783). (NEDO)

  12. Fiscal 1997 research report on the data collection, evaluation and analysis in the PV power generation field test project for public facilities; 1997 nendo kokyo shisetsu nado yo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As a part of the field test project for diffusing PV power generation into public facilities generally, evaluation and analysis were made on the collected data from 105 sites installed during fiscal 1993-1996. Analysis of operation characteristics was made by using parameters obtained by developing a basic equation for every component. 94% of all the sites fell under the total solar irradiation of 3.0- 4.5kWh/m{sup 2}/D. 83% of those fell under the equivalent array operation time of 2.5-4.0h/D. 70% of those fell under the equivalent system operation time of 2.5-3.5h/D. 72% of those fell under the system operation time of 9.0-12.0h/D. 78% of those fell under the effective inverter efficiency of 0.84- 0.96. 68% of those fell under the inverter load factor of 0.25-0.35. 85% of those fell under the array performance ratio of 0.7-1.0. 83% of those fell under the system performance ratio of 0.6-0.9. The generation cost decreased from 270yen/kWh in 1993 to 100yen/kWh in 1996 because reduction of an installation cost largely contributed to reduction of the total cost. (NEDO)

  13. Report on FY 2000 project for drawing district energy-saving visions for Village of Satomi; 2000 nendo Satomi-mura chiiki sho energy vision sakutei nado jigy hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The district energy-saving visions are drawn for Village of Satomi, aimed at construction of an energy-saving, resources-recycling type farming village in mountains, friendly to the environments, and the implementation organization is established. The activities include (1) questionnaire survey for energy saving, with the questionnaires sent to the citizens and enterprises, (2) actual situations of energy consumption, (3) setting the hardware and software targets achievable in 5 years, (4) setting the projects for introducing energy-saving facilities, and (5) establishment of the energy-saving spreading committee, and drawing the action programs. Insufficient practices are pointed out, and necessity for the spread/enlightenment activities are clarified. At the same time, it is estimated that the energy consumption can be potentially reduced by 8% in 5 years. It is decided to introduce a co-generation system in the biomass recycling center, systems for photovoltaic power generation and production of hot water by solar heat in the integrated day-care center, and wind power system in Plateau Satomi. (NEDO)

  14. FY 2000 Project report on survey for drawing district energy-saving visions for City of Oguchi; 2000 nendo Oguchi-shi chiiki sho energy vision sakutei nado jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    The energy-saving visions are drawn for City of Oguchi to help spread the energy-saving practices through the citizens, based on the studies on more efficient and realizable energy-saving measures, including effective utilization of district energy. The energy-saving activities cover the following 6 areas: (1) energy demand trends and current status of energy-saving measures, (2) basic environmental conditions related to energy saving in the district, (3) prediction of energy demands, (4) basic conception of the district energy saving, and introduction methodology, (5) energy-saving implementation plans, and (6) promotion of and problems involved in introduction of the energy-saving measures. The energy-saving implementation plans cover the public facilities, household, schools and private enterprises, and the energy-saving measures studied for the public facilities include introduction of microhydroelectric power generation systems for service water and sewer systems, revolving doors for libraries, high-efficiency illumination systems, and various types of solar systems. Those for household include economic utilization of home electric appliances and automobiles, and those for cooperation by the administration and citizens include thorough separation of garbage. (NEDO)

  15. New Sunshine Project for fiscal 1997 on the international cooperation project. Cooperation in solar energy technologies among Japan, Australia and other countries; 1997 nendo new sunshine keikaku kokusai kyoryoku jigyo. Nichigo nado taiyo energy gijutsu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes the state of progress in the cooperation in solar energy technologies among Japan, Australia and other country, the memorandum concluded for the new project, and the activity report on the NEDO/MUERI project. The progress in the cooperation in solar energy technologies among Japan, Australia and other country is divided into that of the new project and that of the continued project. The former relates to the start of the long-term endurance test project for photovoltaic solar modules in Oman. The location of the endurance test is the Sultan Qaboos University in the suburb of Muscat. Modules subjected to the endurance test consist of ten modules of five types. The test will be performed on air temperature, humidity, wind directions, insolation on horizontal surface, insolation on slanted surface, ultraviolet ray intensity, module temperatures, and electric characteristics of the modules. The continued project is an outdoor endurance test for the photovoltaic solar modules begun in fiscal 1996, which is executed by the Murdock University Energy Research Institute (MUERI). The endurance test locations were selected at Darwin, Alice Springs and Perth. This paper reports the photovoltaic solar module endurance test and investigation, as well as the periodical consultations as the activity report of the NEDO/MUERI project. (NEDO)

  16. FY 1999 survey report on the survey to grasp new technologies for destruction of freons, etc. in Japan; 1999 nendo Nippon no atarashii freon nado hakai gijutsu no haaku chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    At the end of 1995, a total abolition of the production of the specified freons (CFC) was achieved. In future, it will be important to proceed with the appropriate recovery/destruction of the CFC, etc. which has been used so far, not only for the protection of ozone layer, but for the prevention of global warming. For the international study of facilities (technology) for destruction CFC, etc., the Technical Assessment Committee (TAC) was installed for destruction technology of ozone layer depletion substances (ODS) under the United Nations Environment Programme (UNEP), and the destruction efficiency (DE) of ODS was set up. In Japan, more than 30 facilities are already handling the destruction of CFC on a commercial basis. The number is expected to increase by the promotion of protection of ozone layer and prevention of global warming. This survey indicated quantitatively and qualitatively based on the TAC DE what the facilities for destruction of CFC should be which were considered of domestic laws in Japan, and was made a guide for existing facilities and ones to be newly installed. (NEDO)

  17. Study of immersed heat exchange surface for high efficiency heat recovery from wire rim tires in a fluidized bed boiler; Hai tire nado kara no kokoritsu netsukaishuyo ryudosho boiler no sonai dennetsukan no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Oshita, T; Nagato, S; Miyoshi, N; Hosoda, S [Ebara Corp., Tokyo (Japan)

    1996-07-10

    In an ICFB boiler, the fluidized bed is separated by a partition into the main combustion and the heat recovery chambers. The flows in these chambers are generated by using silica sand as the fluidizing medium. To determine the overall heat transfer coefficient (HTC) of the boiler`s panel type immersed heat transfer tulles, combustion tests were performed with wire rim tires. The overall HTC of a panel tube array was lower than that of a zigzag tube arrangement. In practice, the heat absorbed by the fins makes the coefficients of either type of tube array almost identical. The air flow rate in the circulating bed at the loot Tom of the heat recovery chamber can be changed to control the overall HTC to a value virtually identical with that of a zigzag tube array. The combustion of wire rim tires leads to a buildup of wires in the zigzag array hampering the transfer of heat. Yet, the panel type array showed no buildup so that it was possible to maintain steady operation with this type of tube arrangement. 8 refs., 10 figs., 2 tabs.

  18. Fiscal 1997 research report. International energy use rationalization project (Analytical tool research project for energy consumption efficiency improvement in Asia); 1997 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo (honpen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    Efforts have been under way to prepare inter-industry relations tables and energy data for four Asian countries, namely, China, Taiwan, Singapore and Malaysia, and a tool for energy consumption efficiency analysis has been developed and improved. In Chapter 1, energy supply and demand in the above-named four countries is reviewed on the basis of recent economic situations in these countries. In Chapter 2, bilateral inter-industry relations tables usable under the project are employed for the analysis of the economic status of each of the countries and energy transactions between them, and a method is described of converting the tables into one-nation inter-industry relations tables which meet the need of this project. In Chapter 3, national characteristics reflected on the respective energy input tables are described, and a method is shown of converting a nationally characterized unit energy table into a common unit energy input table for registration with a database. In Chapter 4, the constitution of the Asian energy consumption efficiency improvement analyzing tool and a system using the tool are explained. In Chapter 5, some examples of analyses conducted by use of the analyzing tool are shown, in which the energy saving effect and CO2 emission reduction effect are estimated for Indonesia by use of the analyzing tool. (NEDO)

  19. Report for fiscal 1999 on the fundamental survey on promotion of joint implementation. Modernization of Bakabad Cement Factory; 1999 nendo kyodo jisshi nado suishin kiso chosa Bekbad cement kojo kindaika chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the result in fiscal 1999 of the feasibility study applied with the COP3 clean development mechanism for Bekabad Cement Factory in the Republic of Uzbekistan. One of the existing three old type kilns were diverted and converted into a dry NSP type kiln (having the same production capacity as the present of 726,000 tons a year). This arrangement was intended to enhance the productivity, save the energy, and reduce emission of greenhouse gases and different pollutants by renewing the upper and lower stream facilities and installing such environmental devices as electric dust collectors and bag filters. The total construction cost is US$84,432,000. Reducible energy consumption and reduction quantity of greenhouse gases would be 73,232 toe/year and 176,528 toe/year, respectively, in the single fiscal 2006. The cumulative quantity over twenty-year period until 2025 would be 1,464,640 toe and 3,530,560 toe, respectively. The energy saving effect per US$1,000 would be 17.87 toe, and the greenhouse gas reduction effect would be 43.08 t. In the case of using a soft loan such as the special yen loan for environment application, the internal profit rate after tax would be 7.63%, which is not high as the business enterprise profitability. However, the profit and loss statement indicates creation of profit after two years of operation, hence there is a relative realization possibility. (NEDO)

  20. Fiscal 1998 overseas geological structure survey. Japan-China joint coal survey Mei-Xian project; 1998 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Chugoku sekitan kyodo tansa Mei-Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Japan-China joint coal survey was made through seismic prospecting by Japanese group and drilling prospecting by Chinese group. Mei-Xian mine property includes coal seams of the Jurassic period, and is covered with the quaternary period stratum without any coal seam. The base of the quaternary period stratum exists at depth of 50-400m, while the coal seams at depth of 300-700m. Among 11 existing seams, the 1st and 5th seams are main objects for prospecting. The 5th seam of 0.2-8.96m (2.95m in average) thick is the most expected important one, distributing all over the mine property. The 5th seam also has branch seams spreading over 2.5km from east to west and 1.2km from south to north in the center part of the mine property. The 1st seam of 0-8.62m (2.90m in average) thick is most thick in the south part of the mine property. The theoretical amount of coal deposits in the whole coal seam is estimated to be nearly 290,000,000t by Chinese group (nearly 50% of it in the 5th seam). That is also estimated to be nearly 346,000,000t by Japanese group (155,000,000t in the 5th seam). Both 1st and 5th seams are composed of sub-bituminous coal. (NEDO)

  1. Research report for fiscal 1988. Basic research for the promotion of joint implementation etc. (plan for using combined cycle at Konakovo Power Station, Russia); 1998 nendo kyodo jisshi nado suishin kiso chosa. Roshia renpo KONAKOVO hatsudensho combined cycle ka keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    On the basis of Kyoto Protocol-provided flexible measures such as joint implementation and clean development mechanisms, a study is conducted for introducing combined cycle into Konakovo Power Plant of Russia currently equipped with antiquated eight 300MW power plants constructed in the 1960's for which early renovation is necessary. The power station is an important power source connecting to the Moscow-Petersburg main. The gas turbine combined facilities to be newly installed will comprise 250MW-class state-of-the-art gas turbines arranged in four blocks, capable of a total output of 1600MW at a thermal efficiency of 58% (with simultaneous supply of heat). Four units capable of 1200MW out of the existing units will stay in operation for load adjusting. Since the price of power is set low under government control, the accounting capital/internal return rate is as low as 2.3%. The rate recalculated under the financing conditions of special yen credit for environmental protection, however, is as high as 19%, so high as to make the renovation an economically feasible project. It is expected that there will be an annual CO2 reduction of 2.3-million tons or a reduction of 57.50-million tons in 25 years (the life span of the new facilities). The renovation may be a joint implementation project to which both Japan and Russia will attach the highest priority. (NEDO)

  2. Report for fiscal 1998 on commissioned operation for research cooperation related to simplified purification system for industrial waste water; 1998 nendo sangyo haisui nado no kan'i joka system ni kansuru kenkyu kyoryoku hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With an objective to serve for environmental preservation in developing countries, joint researches have been performed on anaerobic waste water treatment systems utilizing bio-technology. This paper summarizes the achievements in fiscal 1998. This fiscal year has performed the bench scale test and the operation research of an anaerobic waste water treatment pilot plant jointly with the Standards and Industrial Research Institute in Malaysia on waste waters from the vegetable fat and oil chemical industry. In the bench scale test, data were collected on the oil removing effect of the pressurization and flotation treatment, and the characteristics of the anaerobic treatment. Operation research was performed in the pilot plant by using the anaerobic waste water treatment plant and the aerobic treatment facility. In addition, a feasibility study was carried out to evaluate an optimal treatment system. Furthermore, three researchers were received from Malaysia to whom lectures were given on the Japanese anaerobic treatment technologies, and visits and operation training on the waste water treatment facilities. (NEDO)

  3. Research report for fiscal 1998. Survey on the researchers and research institutes for the effects of global warming and its countermeasures; 1998 nendo onshitsu koka gas ni yoru kankyo eikyo nado ni kansuru kenkyusha kenkyu kikan chosa chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researchers and research institutes across the world (except those in Japan), engaged in the study of global warming and measures to deal with the phenomenon, are extracted in compliance with certain specified standards, and the latest information on them is appropriately arranged and listed. It is further developed into an electronic database for the convenience of users. The collected information includes more than 230 research institutes and more than 1,000 researchers. The endeavor is exerted by extracting essays and institutes mainly out of the on-line databases. More than 1,000 essays and 130 institutes are covered. Visits are made to five institutes in the U.S. and four in Europe who are most actively engaged in the study of global warming, and detailed researches are conducted and information is exchanged. The Argonne National Institute copes with all energy problems related to global warming. Descriptions are given about environmental impact surveys and CO2 isolation in the ocean at the Center for Global Science of the Massachusetts Institute of Technology. At the Oak Ridge National Laboratory, the visitors heard explanations of technologies related to renewable energies and so forth. Researches are made into ecosystems at the University of California, and into natural energies at the University of Hawaii. Also visited are research institutes in Australia, Germany, Netherlands, and Britain. (NEDO)

  4. FY 2000 report on the basic survey to promote Joint Implementation, etc. Survey of gas-fired cogeneration in Samarkand City; 2000 nendo kyodo jisshii nado suishin kiso chosa hokokusho. Samarkand shi gas daki cogeneration chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In the existing heat supply plant in Samarkand City in Uzbekistan, feasibility study was conducted of the project aimed at energy conservation and reduction in greenhouse effect gas emission by introducing the repair/cogeneration system of the regional pipes superannuated. In the project, the following were planned: introduction of two units of 6MW class gas turbine cogeneration, introduction of boiler which can realize 90% of the thermal efficiency, replacement of the existing regional pipes with pre-insulated pipes with less water leak/heat loss, etc. As a result of the study, the energy conservation amount was 21,006 toe, and the amount of greenhouse effect gas reduction was 64,998 t-CO2/y. As to the effects vs. expenses, the energy conservation was 2.80 toe/million yen, and the greenhouse effect gas reduction was 8.66 t-CO2-y/million yen. The initial investment amount was 7.51 billion yen, the business profit was 468 million yen/y, and the internal earning rate was 1.133%. It was judged that great profitability was not expected for the project, but the profit was returnable on investment. (NEDO)

  5. Basic investigation on promotion of joint implementation in fiscal 2000. Project for modification of Pridneprovskaya power plant in Ukraine; 2000 nendo kyodo jisshi nado kiso chosa hokokusho. Ukraine Pridneprovskaya hatsudensho kaishu jigyo keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With objectives of saving energy and reducing greenhouse gas emission at the Pridneprovskaya power plant in Ukraine, a scrap and build project has been discussed. This project will abolish the unit No.12 among the eight units in the existing coal burning power generation facilities, and install a natural gas burning combined cycle plant comprising of three units each with an output of 100 MW. The new plant facilities will consist of gas turbines, steam turbines, HRSG and auxiliary devices, and an air-cooled synchronous power generator with a capacity of 119 MVA. Use of natural gas as fuel reduces generation of soot, sulfur oxides, nitrogen oxides, and CO. In addition, the hot effluent and waste liquor effluent will decrease from those at the present plant. The required fund will be 30,107 million yen. The energy saving effect of this project is reduction of about 7.5 million tons of crude oil equivalent as a total in 40 years. The greenhouse effect gas will decrease by about 39 million tons as a total in 40 years. The profitability estimation calls for the number of investment recovery year of 16 years, and internal profit rate of 7.32%, wherein the implementation of the project cannot be expected as a project to be carried out by private funds. (NEDO)

  6. Fiscal 2000 survey of geological structures overseas. Exchange of engineers with Indonesia (Coal mining technology); 2000 nendo kaigai chishitsu kozo nado chosa hokokusho. Gijutsusha koryu jigyo (tanko gijutsu bun'ya) Indonesia

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Indonesia rich in coal resources consumed 70-million tons of coal in 1999, which covered 17% of its total energy demand. It is estimated that as much as 120-million tons will be produced in 2005, and it is expected that underground mining will increase. Under such circumstances, Indonesia strongly desires that Japan's underground mining technologies be transferred to Indonesia. For the transfer of technologies especially involving production control and management out of Japan's underground mining technologies, Japan dispatched engineers to Indonesia under a mining engineer exchange project, and received and trained Indonesian engineers. Under the engineer exchange project, five engineers were dispatched to Indonesia and gave lectures and on-site training in the period July 9 through August 5, 2000. Japan received seven engineers, who were given lectures and training at the Ikeshima mining field of Matsushima Coal Mining Company in the period November 12 through December 12, 2000. (NEDO)

  7. FY 2000 report on the survey of the overseas geological structure. Japan-China joint coal exploration - Yu Xian project; 2000 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Chugoku sekitan kyodo tansa Yu Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The geological survey was carried out which is needed for coal mine design in the Yu Xian coal mine area, Yu Xian coal field, Hebei province, China. The term of survey was 5 years from 1996 to 2000. Activities are mainly for seismic survey and boring survey. Japan was in charge of the seismic survey, and China in charge of the boring survey. Both attained the goal. The results of the activities were summed up in the following 7 items: 1) outline of the survey; 2) general investigation; 3) state of the exploration related materials/machinery; 4) field survey; 5) items of survey; 6) results of the survey; 7) conclusion. In 6), the geological analysis, coal quality survey and coal amount survey were conducted. In the geological analysis, analyzed were the succession of strata, geological structure, and the situation of existence of coal seams. In 7), the following were made clear: geological structure of the survey area, coal seam, coal quality, hydrological geology, other conditions of drilling technology, and coal amount. The coal amount was 328.34 million tons in a total of A/B/C class coals. The total coal amount of Nos. 1 and 5 coal seams was 259.79 million tons, which was 79.1% of the total coal amount in all area. The average thickness of Nos. 1 and 5 coal seams, which are the main minable coal seams, was 3.10m and 2.66m, respectively. (NEDO)

  8. Report on investigations in fiscal 2000 on the basic investigation on promotion of joint implementation. Rehabilitation of ICE/SAN ANTONIO power plant; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. ICE/SAN ANTONIO hatsudensho rihabiri

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Costa Rica takes a power generation system using hydro power generation as the main source, and possesses medium-capacity gas turbines to supplement needs in the dry season and the peak load. However, a problem has come up that, in addition to the cost rise in gas turbine fuel, the power generation efficiency has been aggravating due to aged deterioration of the generators being used. In association therewith, the problem is now a factor to increase CO2 emission, which is a worldwide problem. Keeping in mind to link it to the clean development mechanism (CDM), the present project is, taking up the SAN ANTONIO power plant as the investigation object, intended to perform a comprehensive discussion on the CO2 emission reducing effect, profitability, and proliferation effect, by executing the conceptual plant design. The up-grading plan for thermal power generation systems in Costa Rica consists of replacement of the gas turbines, handling of phase modifiers, and achievement of the combined cycle. The plan agrees with the present feasibility study intended of CO2 emission reduction, consisting of the modification plan of the SAN ANTONIO power plant, that is the plan to replace the over-aged gas turbines at the power plant. Its necessity has been identified. It was disclosed that the project has the effects of reducing CO2 of 82,000 tons annually, and the investment can be recovered in nine years. (NEDO)

  9. Fiscal 1998 research cooperation project. Research cooperation on diversity preservation and sustainable use for living organisms; 1998 nendo seibutsu tayosei hozen to jizokuteki riyo nado ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report describes the titled research cooperation. Joint R and D with Thailand, Indonesia and Malaysia was made on collection and preservation of bio-resources such as tropical rain forest, and sustainable use of them by developing countries themselves. The project includes the simple identification and preservation technology of biospecies such as microorganism, assessment and monitoring technology of ecosystem, search of useful functions of biospecies, and construction of a bio-resource information network. This project promotes conversion of excessive hunting into resource conservation in agriculture, forestry and fisheries industries, and establishment of the basis of new product development in chemical and pharmaceutical industries. This project also contributes to preparation of the basic scheme of developed countries including Japan to countries holding bio-resources in addition to industrial basis preparation of every country. Until 1997, basis establishment has been made such as training of researchers, preparation of equipment and technical guidance, and in the final 1998, various results such as extraction of promising samples from microorganisms were obtained. (NEDO)

  10. FY 1998 basic survey to promote the joint execution, etc. Plan for repair of Schekinskaya thermal power plant; 1998 nendo kyodo jisshi nado suishin kiso chosa. Schekinskaya karyoku hatsudensho kaishu keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project is a feasibility study to get effects of reducing greenhouse effect gas by repairing Units 8, 9, and 10 (330MW in total) of Schekinskaya thermal power plant and Units 1-7 (450MW in total) of Novomoskovskaya thermal power plant. Both are very old brown coal fired thermal power plants which were constructed during 1947-1967. At present, they are run fired by natural gas. Being very superannuated, they need repair of the facilities. In the adjustment of opinions with Russia, the plan was aimed at substantial reduction of greenhouse effect gas by increasing thermal efficiency of power plant. For it, a 800MW class gas turbine combined cycle power plant is constructed at Novomoskovskaya power plant where there are existing buildings and space for equipment and where gas fuel can be used. As a result of the study, it was indicated that the reduction amount of greenhouse effect gas after the repair becomes 1,853,966 tons/yr as against 3,590,514 tons/yr before the repair. (NEDO)

  11. Fiscal 2000 survey report on technological trends. Survey on trend of high-density energy beam technology concerning conservation of energy; 2000 nendo gijutsu doko nado chosa hokokusho. Energy shiyo gorika ni kakawaru komitsudo energy beam technology no doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    There is a possibility that machining technology using high-density energy beam will bring an epoch-making change to micro-nano area processing. In particular, a laser beam having high controllability is indispensable. This is a report of the fiscal 2000 survey. The survey was conducted on laser beam generation, control and nano-diagnostic techniques, micro-nano optics technologies and machining technologies, with the development problems and targets summarized. Laser beam generation/control technologies, which become the basic tools for micro-nano manufacturing, were investigated, as were inspection technologies for the purpose of checking the functions of nano structures created. Particularly, the investigation elucidated the significance of development of a femtosecond solid state laser based on a semiconductor laser and the control techniques of their phase. Further, necessity was emphasized in developing X-ray probing, infrared and terahertz spectroscopy which are essential for nano-diagnostic techniques. In optics technologies, the paper described the importance of photonic crystals which enable less-than-wavelength machining or electrical beam control using interference effect. The possibility of fabricating photocatalysts with nano-particles was also mentioned, as was the manufacturing of nano-functional structures. (NEDO)

  12. Fiscal 1999 research report. Basic research on joint implementations promotion (Feasibility study of modification for Tehran Cement Co., Ltd., Iran); 1999 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Iran koku Teheran cement sha kaizo F/S

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The feasibility study was started upon a request made by the Iranian Ministry of Energy involving the No. 7 kiln of the above said company. It was then concluded, after assessing the degree of urgency of supply and demand and the magnitude of loss due to reduced production because of the on-site modification work, that it was not practical to begin the project immediately. Under the circumstances, various studies were made about the feasibility of modification of the whole production process of the No. 1 kiln through No. 7 kiln, and a procedure was presented, to be described below. The procedure will consist of Phase I wherein the No. 3 wet kiln is converted into an NSP (new suspension preheater) dry kiln, Phase II wherein the No. 7 SP (suspension preheater) dry kiln is converted in to an NSP kiln, and Phase III wherein the No. 4 SP dry kiln is converted into a clinker cooler. Under this procedure, the modernization of the Tehran Cement Co., Ltd., facilities will be accomplished without causing production loss. After the completion of the project, an annual yield of 3.6-million tons will be achieved, with productivity to be improved by 26.4% over the current theoretical capacity or by 54.8% over the actual average for the past 5 years. There will be a sustained conservation of 25,356 tons/year in terms of oil. Application of CDM (clean development mechanism) to this project will be extremely effective in reducing greenhouse gas and in improving profitability. (NEDO)

  13. Report on a commercialization fundamental investigation (in Batulicin Area, Indonesia) in relation to FY 1997 investigations on geological structures in overseas countries; 1997 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Indonesia Batulicin chiku) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A fundamental coal mine development investigation was carried out in Batulicin Area, Kalimantan, the Republic of Indonesia. The investigation included ground surface surveys, preparation of topographical maps and geological maps, trial drilling investigation, physical logging, chemical analysis, and infrastructure investigation. The trial drilling investigation was intended to identify the existence conditions of coal beds and coal quality, and was performed by forming grids with about 500-meter interval, and using 21 trial drillings to depths of 104 to 240 meters for a total drilling length of 3463 meters. The physical logging included electric logging, radioactivity logging and pore size logging, and the trial drilling cores were subjected to chemical analysis. For infrastructures, investigations were carried out on necessity of modifying existing roads, privilege relationship, the current status of barge loading points, water depths, and land acquisition. The result of the investigation revealed that minable coal quantity in underground mining of the coal bed B would be 13.189 million tons, and that annual production of original coal at 733,000 tons would be possible by adopting a long-wall type mechanized coal mining system. 14 refs., 99 figs., 25 tabs.

  14. Report on the survey in fiscal 1998. Basic survey on promotion of joint project implementation (Khabarovsk thermal power plant modification plan); 1998 nendo chosa hokokusho. Kyodo jisshi nado suishin kiso chosa (Khabarovsk karyoku hatsudensho kaishu keikaku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Discussions were given on the modification plan for Khabarovsk Thermal Power Plant as part of the basic survey on promotion of joint project implementation based on the COP3. The plan calls for shutting down the overaged power plant No. 1 (462.5 MW) and newly building the power plant No. 4 with high efficiency to reduce CO2 emission. The plant will use coal, which is mined extensively in the region. The plant will be a combined heat and power plant with a total power generation output of 576 MW and a total thermal output of 1140 Gcal/h. Effect of reducing CO2 emission as the result of this modification plan will be as much as about 1.2 million tons annually. The plant will use coal as fuel in the beginning, but if it uses natural gas in the future, for which pipeline construction from Sakhalin has been planned recently, the CO2 emission reducing effect will reach 2.4 million tons. Internal profitability was calculated with the CO2 price set at zero US dollars and with the foreign exchange rate varied, for a case of firing coal for 30 years. The profitability may vary largely according to the foreign exchange level, such as profit rate of 5.47% at 20 roubles to a US dollar, 11.04% at 12 roubles, and 21.22% at 6 roubles. The profitability should be judged somewhat low under the current exchange rate of 20 roubles to a dollar. Financial provision with a favorable condition is strongly desired. (NEDO)

  15. Basic investigation on promotion of joint implementation in fiscal 2000. Efficiency improvement project for gas turbine power plant in Iran; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Iran gas turbine hatsuden plant no koritsu kaizen project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Investigations and discussions have been given on measures to improve energy conservation and efficiency at a power plant of Kish Water and Power Company (KWPC) in Iran. The site has high ambient temperature throughout a year, making the gas turbine power plant capable of generating power only at about 70% of the rated output, with the power generation efficiency decreasing. The project has analyzed the current situation at the plant, and evaluated different means that appear effective in improving the efficiency, including the gas turbine absorbed air cooling system, the steam injection system, and the combined cycle. As a result of the discussions, it was revealed that energy saving effect can be obtained at 145 TJ with the gas turbine absorbed air cooling system, 224 TJ with the steam injection system, and 1017 TJ with the combined cycle. The annual reduction of greenhouse gas emission due to the above energy conservation would be about 11 thousand tons, 16.5 thousand tons, and 75 thousand tons, respectively. However, the investment payback period would be about 2.45 years, 8.31 years, and 14.21 years, respectively. Therefore, the profitability does not appear very attractive because of low fuel unit cost. (NEDO)

  16. Fiscal 1998 geological survey overseas. Report on Tanjung Enim project for Japan-Indonesia joint coal exploration; 1998 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Indonesia sekitan kyodo tansa Tanjung Enim project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For disclosing stratigraphy and lithofacies and for clarifying the status of coal beds in the southern Arahan area (55km{sup 2}), South Sumatra, ground surface exploration, borehole drilling, borehole geophysical logging, and seismic reflection monitoring were carried out. The survey covered a rectangular area, 11km from east to west and 5km from north to south and 60m to 130m in elevation. In the ground surface exploration effort, trenching was performed at three spots in coal bed outcrops in an quasi-accurate survey with route gaps of roughly 1,200m. Ten boreholes were drilled. The deepest one was 282.20m deep and the shallowest one 117.80m deep, with the total drilled length measuring 1,643.70m. Seismic reflection monitoring was implemented using three traverse lines (two running north to south and one running from east to west), with the three lines measuring 10.92km in total. VSP (vertical seismic profiling) was carried for borehole ASN17 only. The findings are that there are four kinds of coal beds, that is, A2, B, C, and E spreading all over the area, that their thicknesses are estimated to be 12m, 18m, 7m, and 6-8m, respectively, and that coal beds A2, B, and C are packed into between 80m-deep and 150m-deep levels. (NEDO)

  17. International measures project for rational energy use (Survey project of the analysis tool of Asian energy consumption efficiency). List of errata; 1998 nendo kokusai energy shiyo gorika nado taisaku jigyo seigohyo. Asia energy shohi koritsuka bunseki tool chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The list of errata was prepared for the data book of the international measures project for rational energy use (Survey project of the analysis tool of Asian energy consumption efficiency). Corrected pages of the data book 1 (1990) are as follows: 187-190, 223-226, 259-262, 295- 298, 369-370, 387-388 and 405-406 on Malaysian data. Corrected pages of the data book 2 (1985) are as follows: 102-105 on Chinese data, 154 on common data, and 187-190, 223-226, 259-262, 295-298, 369-370, 387-388 and 405-406 on Malaysian data. (NEDO)

  18. Fiscal 1998 research report on information structuring technology for advanced use of NEDO research reports; 1998 nendo NEDO seika hokokusho nado no kodo riyo ni hitsuyona joho kozoka gijutsu no chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research was made on electronic NEDO research reports corresponding to the recent extending trend of Internet. The logical structure and electronic format of NEDO research reports as document were first studied considering document disclosure and reuse of technical information. HTML as electronic format for Internet is unfortunately insufficient to describe the logical structure of NEDO research reports because of HTML's restricted description. Thus, XML which is being watched because of its possible definition of original tags was studied in place of HTML. As a result, because at present preparation of standards on XML and a compatibility for implementation of standards are insufficient, it was concluded that construction of the electronic document system for NEDO research reports is still too early. However, since adoption of XML as document format is important from the viewpoint of a property succession on Internet, preparation of the XML format file of NEDO research reports is essential. (NEDO)

  19. FY 2000 report on the basic survey to promote the joint implementation. Project on the repair of the Bobovdol thermal power plant, Bulgaria; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Bobovdol karyoku hatsudensho kaishu jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to the Bobovdol thermal power plant, Bulgaria, a plan for repair of power plant was worked out with the aim of energy conservation and greenhouse effect gas emissions, and the results of the feasibility study were reported. The existing power plant, 3 x 210MW unit, totals 630MW, approximately 130,000 hours in cumulative operation hour. In the repair plan, the plant is replaced with high efficiency gas combined cycle power generation facilities based on gas turbines by scrap and build. In the plan, the repair of existing units Nos. 1 and 2 for life elongation is urgently conducted, and new facilities are to be built every 5 years. As a result of the study, the energy conservation effect will be reduced by 16.37 million toe tons in 41 years after the repair, and the CO2 emission will be reduced by 105.18 million tons in 41 years after the repair. As to the profitability, the internal economical profitability is 5.66% in case of setting the CO2 emission trade at zero. This is the level on which the project is barely profitable by soft loans raised by Japan Bank for International Cooperation (JBIC), etc. (NEDO)

  20. Report for fiscal 1994 on commissioned operation for research cooperation related to simplified purification system for industrial waste water; 1994 nendo sangyo haisui nado no kan'i joka system ni kansuru kenkyu kyoryoku hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    With an objective to serve for environmental preservation in developing countries, joint researches have been performed on anaerobic waste water treatment systems utilizing bio-technology. This paper summarizes the achievements in fiscal 1994. In the research cooperation with Thailand, a reactor applicability test was performed by using a pilot plant to determine the operating conditions, and necessary data were obtained. The pilot plant was completed of installation in November. In the research cooperation with Indonesia, Tofu manufacturing waste water was selected as the object of pilot plant research. In the detailed design the Tofu manufacturing waste water shall be treated anaerobically, and the kitchen waste water shall be treated aerobically to acquire the intended water quality. In the research cooperation with Malaysia, as a result of visiting six industries and 22 factories for investigation, waste waters from chemical and foodstuff factories were selected as the object waste waters for the research. Three researchers from Thailand and Indonesia respectively were received in Japan to provide education including experimental training and visits to waste water treatment facilities. (NEDO)

  1. FY 1999 research cooperation project - the research cooperation on the protection of biodiversity and sustainable use, etc. Follow-up; 1999 nendo seibutsu tayosei hozen to jizokuteki riyo nado ni kansuru kenkyu kyoryoku. Follow up

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The follow-up for the research cooperation for Indonesia, Malaysia and Thailand was conducted to make it possible that developing countries themselves protect biological resources in the tropical area, etc. and make the sustainable use of biological resources using bio-technology. In Indonesia, the follow-up was to be made for proceeding with the joint study for 'The study on the plant utilization technology - search for useful plant ingredients' reported by Professor Koshimizu, Kinki University. In Malaysia, considering that equipment is enough installed there and research leaders are very excellent, it is considered that the country is suitable for the partner of future joint research on microorganisms with Japan. Moreover, the merit in joint study is the cooperation in study of information system and culture collection. In Thailand, Japan told them that the study theme has to be made smaller toward the culture collection rich in content and the search for useful plants/bacteria. (NEDO)

  2. FY 2000 report on the basic survey to promote Joint Implementation, etc. Survey on the repair plan for Fenchugangi fertilizer plant in Bangladesh; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Bangladesh koku Fenchugangi hiryo kojo kaishu keikaku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of conserving energy and reducing greenhouse effect gas emission, survey was conducted for the repair plan for Fenchugangi fertilizer plant in Bangladesh. In the survey, studied were measures to increase production, measures to prolong the plant life, energy conservation measures and environmental measures. As a result of the study, it was confirmed that if the production amount targeted at first is recovered and the consumption amount of natural gas can be reduced down to the original target by rehabilitating the superannuated equipment/machines and by supplying/preparing the spare parts in shortage, the reduction in greenhouse effect gas emission is achieved and the production cost of urea fertilizer is lowered. Further, it was found that by carrying out this, energy efficiency can be heightened at the parts which can be replaced with the newest processes. The energy conservation amount calculated was 25,890 toe/y, and the amount of greenhouse effect gas reduction 60,448 t-CO2/y. The investment amount was approximately $19,106,000. The total interest is to be raised by soft loan, and the internal earning rate was 9.04% with the present prices of natural gas and urea. (NEDO)

  3. FY 1998 basic survey to promote the joint execution, etc. Overall repair plan of thermal power plants in Maritime Province of Russia; 1998 nendo kyodo jisshi nado suishin kiso chosa. Roshia Enkaishu ni okeru karyoku hatsudensho sogo kaishu keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For thermal power plants in Maritime Province of Russia, a repair plan for effective reduction of emission of greenhouse effect gas was worked out as a draft plan for the joint execution. The project is to be implemented for the additional installation/replacement of boilers at Vladivostok No. 2 power plant, construction of a power plant as a substitute for Partizansk power plant, and new construction of Ussuriisk power plant. The draft plan includes the new installation of two gas-fired boilers/replacement of existing boilers at Vladivostok No. 2 power plant, construction of 200MW cogeneration facility at Partizansk power plant, construction of 180MW cogeneration facility at Ussuriisk power plant, abolition of small-sized boiler station, etc. The reduction amount of the greenhouse effect gas emission based on this repair plan totaled 338 million tons in project. The effect against cost is US$ 4.75 per 1 CO2 ton at Vladivostok. (NEDO)

  4. FY1998 survey report on the site surveys on regional situations in improvement in energy consumption (Cambodia and Bangladesh); 1998 nendo energy shohi koritsuka nado chiiki josei genchi chosa hokokusho (Cambodia, Bangladesh) chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to promote technical cooperation of Japan with Asia in the energy aspect, site surveys were carried out on improvement in energy consumption efficiency. Electric power supply in Cambodia is made mostly from EDC, whose power generation amount in 1997 was 310 million kwh, while the power sold was 230 million kwh, with 26.1% of the total generation amount, or 80 million kwh being wasted as the loss. Existing power generation facilities are old and small in scale, made by the former Soviet Union making the repair difficult. The loss is enormous because of aging in power distribution facilities, overload operation, and power stealing. The efficiency is extremely poor, whereas improvement in efficiency of the existing facilities is indispensable to cope with the anticipated increase in the demand. In Bangladesh, 90% of the power is generated by using natural gas produced in the eastern part of the country. Many power plants are experiencing decreased efficiency due to the facility aging and insufficient and improper maintenance. The power transmission and distribution departments have had a large loss in power, which has become one of the most important issues. The loss exceeds 30%. The government is trying to achieve efficiency improvement in the electric power business through introducing the principle of competition by establishing new private companies. However, this approach is facing severe objection from the governmental and public labor unions, making the future development opaque. (NEDO)

  5. Basic survey project for joint implementation. Feasibility study for the diffusion of fluidized bed cement kiln system in China; 1998 nendo kyodo jisshi nado suishin kiso chosa. Chugoku ni okeru ryudosho cement kirun fukyu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Discussions were given on conversion of shaft kilns mainly used at Tianjin Cement and Huaxin Cement to the fluidized bed cement kiln of the most advanced type. Possibility of energy conservation in China, that is reduction of carbon dioxide emission, was evaluated. This system has been developed by the Center for Coal Utilization, Japan. The system is characterized by reduction of greenhouse effect gas emission, elimination of the problem of dust scattering from sintering facilities, stabilized production of high-quality clinker, capability of using low-grade coal and anthracite, and reduction of cement production cost. As a result of the discussions, the reduction rate of greenhouse effect gases was found about 17 to 33%. The cost effect may be calculated as 2 to 5 thousand yen per ton of CO2 reduction amount assuming the system life of 20 years. If this process has been diffused into China, the quantity of CO2 to be reduced will reach about four million tons annually assuming a diffusion rate of 10%. This project shows as high profitability as about 20% at IRR, and the system is more advantageous economically than the shaft kiln. (NEDO)

  6. FY 1998 annual report on the survey on overseas geological structures. Project for exchanging engineers (coal mining technology area) (Vietnam); 1998 nendo kaigai chishitsu kozo nado chosaa. Gijutsusha koryu jigyo (tanko gijutsu bun'ya) (Vietnam)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The project for exchanging engineers has been implemented, in order to improve production and managemental techniques of coal mining engineers in the Asia-Pacific region, promote smooth and efficient projects for surveying overseas geological structures, and facilitate stable supply of overseas coal to Japan. The FY 1998 project was concentrated on Vietnam, to which Japanese coal mining engineers were sent, and from which production management engineers were invited to Japan as trainees. The Japanese engineers sent to Vietnam educated the underground coal mining techniques. The Vietnamese management engineers invited were trained for, e.g., production management techniques (e.g., those for workplaces and organizations) in the Japanese mines, administrative management techniques, and techniques to improve safety and productivity in the mines. Coal Energy Center and Taiheiyo Mining's Kushiro Mine provided training facilities. (NEDO)

  7. FY 2000 report on the basic survey to promote Joint Implementation, etc. Upgrading of energy utilization in the cement production process; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Cement seizo kotei ni okeru energy kodoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigational study was conducted of a project for energy conservation and greenhouse effect gas reduction by introducing the steam injection gas turbine generator to production facilities of the Siam Cement Industry Corporation (SCI) in Thailand. In the project, studies were made on the following: no purchases of electric power by introduction of the steam injection gas turbine generator; additional heating by gas turbine exhaust gas by introduction of the kiln combustion air heater; remodeling of the preheater of raw materials, and the partial calcination before kiln sintering by introduction of the calcination furnace. As a result of the study, the energy conservation amount was 1,200 toe/y, and the greenhouse effect gas reduction amount was approximately 8,000 t-CO2/y, which led to the reserve power for increased production of clinker by about 18%. The size of investment was 314.5 million Baht in total. As to the evaluation of economical efficiency of the investment, the actual period of ROI was a little less than 5 years, and the internal earning rate was 17.7%, which substantially met with SCI's standards for equipment investment. However, there are problems on the gas supply infrastructure, recovery of the white cement demand, etc. (NEDO)

  8. Fiscal 2000 report on entrusted follow-up project for research cooperation on simplified industrial wastewater purification system; 2000 nendo sangyo haisui nado no kan'i joka system ni kansuru kenkyu kyoryoku follow up gyomu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The Research Cooperation Project on Simplified Industrial Wastewater Purification System carried out in cooperation with Indonesia and Malaysia was terminated in fiscal 1998. A follow-up check was conducted for spreading the fruits of the project. In concrete terms, for the study of problems to solve for the dissemination across Malaysia of the results of the project implemented in that country, technical guidance was provided relative to the study of operation performed by the counterpart operating their own pilot plant and the like. International Meeting for Technical Exchange was participated in, convened in Thailand in the period March 6-8, 2001. The contents of research activities included the two fields of (1) the selection of coagulants and (2) the study of pilot plant operation. In field (1), PAC (poly-aluminum chloride) and aluminum sulfate were compared with each other in terms of performance and cost in case they were used as coagulants, and then it was made clear that PAC was superior. In field (2), operation was studied using UASB (upflow anaerobic sludge blanket) type facilities of Southern Acid Plant. (NEDO)

  9. Study on ease of handling automobile secondary controls. Part 1. Procedure to seek numbers on radio station selecting buttons; Radio, eakon nado no sosasei. 1. Radio senkyoku button no shikibetsu

    Energy Technology Data Exchange (ETDEWEB)

    Ikemura, S [Meijo University, Nagoya (Japan); Noda, K [Ryowa Sheet Metal Processing Co. Ltd., Aichi (Japan); Nozaki, H

    1997-10-01

    Times to recognize the numbers on the radio station selecting buttons about horizontal straight 6 layout were measured using electro-oculogram. There are two kinds of basic pattern to seek numbers. One is that recognition times of both end numbers are shorter than those of central numbers. The other is that recognition times of all numbers are nearly same. How the subjects seek the numbers was studied using the amount of information and entropy. 6 refs., 8 figs., 5 tabs.

  10. FY 1999 Report on overseas geological structure surveys. Joint Japan-China Yu Xian exploitation project; 1999 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Chugoku sekitan kyodo tansa Yu Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project is based on the (agreement of the joint exploitation project for Yu Xian block in Yu Xian coal mine, Province of Hepei by Japan's NEDO and China's Coal Geological Bureau), signed on October 4, 1996. The joint project mainly comprises seismic exploitation and test drilling, Japan being mainly responsible for the former and China for the latter. The final report will be drawn jointly for the geological survey results necessary for designing coal mines. The Yu Xian block contains the Jurassic coal seams, which are covered by the Quaternary bed and not exposed to the surface. The Quaternary bed base is 50 to 400 m deep from the surface, and coal seams are 300 to 700 m deep also from the surface. A total of 11 coal seams are located in the Xiahuayuan strata as the coal-bearing strata. The first and fifth seams are most promising ones. In particular, the fifth seam is thick (0.2 to 6.91 m thick) and distributed throughout the block. It is estimated that 8 coal seams have a total coal quantity of approximately 346 million tons. (NEDO)

  11. Fiscal 1998 research report. Popularization project of the proper treatment technology of industrial wastes in Asian regions; 1998 nendo chosa hokokusho. Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Study was made on popularization of the proper treatment technology of industrial wastes in Asian regions. In principle, industrial wastes should be recycled in a country concerned, however, because of a difference in technology and industrial location, treatment of all industrial wastes in a country concerned is impossible. International cooperation is thus indispensable to promote proper efficient practical measures for environment. For studying the possibility of the international cooperation between Japan and Asian countries concerned for further recognition and solution of industrial waste problems, 'International Symposium on the Asian Industrial Waste Issue' have been held in Tokyo since 1997 for governmental staffs. In fiscal 1998, Malaysia was invited in addition to China, Philippines and Thailand for popularization of the proper treatment and recycling of industrial wastes in Asian regions. In every Asian countries, poor collection of discharge, treatment and disposal data is an obstacle to effective treatment. Technical cooperation and financial support by developed countries are demanded. (NEDO)

  12. Fiscal 1998 overseas geological structure survey report on the engineer interchange project (coal mine technology field), Indonesia; 1998 nendo kaigai chishitsu kozo nado chosa gijutsusha koryu jigyo (tanko gijutsu bun'ya), Indonesia hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project aims at improvement of coal mining technology and productivity in Indonesia by Japanese production control technology and business management technology for underground coal mining, through interchange of coal engineers between Japan and Indonesia. This project is composed of the short- term and long-term dispatch project of engineers to Indonesia, and the training project of Indonesian engineers in Japan. In fiscal 1998, the short-term dispatch was made for the training in Indonesia on underground coal mine development (development planning, pit mouth selection, main gallery design, mining system selection, transport planning, ventilation planning, under-river mining, mine water proofing, drainage). The long-term dispatch was made for contact and negotiation with concerned Indonesian organizations, support of the training project, and collection of information on the trend of Indonesian economy and energy, and the present and trend of the coal industry for conducting smooth and effective engineer interchange. (NEDO)

  13. Fiscal 2000 report on entrusted follow-up project for research cooperation on simplified industrial wastewater purification system; 2000 nendo sangyo haisui nado no kan'i joka system ni kansuru kenkyu kyoryoku follow up gyomu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The Research Cooperation Project on Simplified Industrial Wastewater Purification System carried out in cooperation with Indonesia and Malaysia was terminated in fiscal 1998. A follow-up check was conducted for spreading the fruits of the project. In concrete terms, for the study of problems to solve for the dissemination across Malaysia of the results of the project implemented in that country, technical guidance was provided relative to the study of operation performed by the counterpart operating their own pilot plant and the like. International Meeting for Technical Exchange was participated in, convened in Thailand in the period March 6-8, 2001. The contents of research activities included the two fields of (1) the selection of coagulants and (2) the study of pilot plant operation. In field (1), PAC (poly-aluminum chloride) and aluminum sulfate were compared with each other in terms of performance and cost in case they were used as coagulants, and then it was made clear that PAC was superior. In field (2), operation was studied using UASB (upflow anaerobic sludge blanket) type facilities of Southern Acid Plant. (NEDO)

  14. Report for fiscal 1999 on basic commercialization survey related to geological structure surveys in overseas countries (Kalewa area, Myanmar); 1999 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa (Myanmar Kalewa chiku) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Commercialization survey was performed on the coal beds in the Kalewa area in the Union of Myanmar by means of geological structure surveys. The site surveys included on-the-ground survey, test drilling survey, sample collection and analysis, and infrastructure survey. The on-the-ground survey area spread out about 5.5 km{sup 2}, wherein nine test wells were drilled (for total distance of 2,046.74 m), and coal and rock sample collection and analysis were carried out on six samples. The infrastructure survey was performed on coal transporting roads, and barge loading planned points and facilities. As a result of the test drilling survey, existence of coal beds with thickness of 4 ft, 9 ft and 6ft was identified. Since the 9-ft bed in particular exists stably with inclination of 40 to 42 degrees over the whole subject area, it was made clear that the bed can be the object of mining as the main coal bed. The coal is the ordinary coal with such good qualities as ash content of 4.72%, total sulfur content of 0.22%, and total calorific power of 6,500 to 6,570 kcal/kg. The defined coal quantity for the 9-ft bed is four million tons, or 7.7 million tons in total if the estimated coal quantity is added. The quantity will amount to 15.3 million tons when those of the 4-ft and 6-ft beds are added. (NEDO)

  15. Survey report 1998. Survey on actual condition of science parks and similar facilities in Asian countries; 1998 nendo chosa hokokusho. Asia shokoku chiiki ni okeru science park nado no jittai chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Implemented at NEDO, on such technical development issues peculiar to developing nations as are difficult to solve by their research and development ability alone, has been a consistent research cooperation with countries in question, such as installation of plants and research facilities, joint research operation, and training of researchers, while Japanese technological skill and research and development know how are utilized, as the international cooperation projects. In this survey, an actual condition was investigated including potential of science parks and similar facilities in Asian countries (Thailand, Indonesia, Malaysia and India), for the purpose of unearthing the needs, seeds, etc., of the future international research cooperation projects. The parks and facilities selected for the survey are as follows. The Thai technology/science parks are the Thai Science Park and four other parks; the Indonesian technology parks are Bukit Indah Industrial City and eleven other parks; the major Malaysian technology parks are Technology Park Malaysia and fourteen other parks; the major Indian technology parks are Electronics City and fifteen other parks. (NEDO)

  16. Report on the project for spread/promotion of technology for the industrial waste optimized treatment in the Asian region; Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The International Symposium `98 on the industrial waste problem in the Asian region was held in Tokyo on February 18, 1998. MITI commented on the present situation of the industrial waste problem in Japan and Japan`s environmental tackling toward the Asian region, and also Asian countries (China, the Philippines, Thailand and Korea) made reports. Japan reported on environmental preservation measures taken in the industrial circle, the industrial waste problem at companies which advanced into Asian countries, effects of the Basel Convention (which restricts border-crossing movement of harmful wastes) on recycle activities, Japan`s role in Asia, etc. In the panel discussion, discussions were made on human interchange in the informatization, recycling technology, shortage of personnel concerned with environmental protection, construction of a network in the Asian region and Japan` s role, etc. As to the treatment system for waste, the necessity was recognized of studying systems which meet with actual states of each country. It is also necessary to go on with discussing how the system should be for cooperation between governments and private companies. Importance of the recycle and information exchange was emphasized. 10 refs., 14 figs., 27 tabs.

  17. Report on the project for spread/promotion of technology for the industrial waste optimized treatment in the Asian region (International Symposium `98); Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo (symposium kaisai) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In Japan and Asian countries, the optimized treatment of industrial waste is the problem with the economic growth. Border-crossing movement of the waste for promotion of the renewable use is also a problem. Therefore, the International Symposium `98 on the industrial waste problem in the Asian region was held. China, Thailand, the Philippines and Korea were invited to Japan to give lectures. MITI of Japan reported on the present situation of Japan and the cooperation with Asian countries. The industrial circle reported on efforts for environmental protection measures to be taken, the industrial waste problem at companies which advanced into Asian countries, effects of the Basel Convention on recycling activities, Japan`s role in Asia, etc. In the panel discussion, promotion of cooperation for recycling technology and Japan`s support for formulating strategy on the industrial waste were requested to Japan, and the construction of an Asian area network was proposed. Concerning the cooperative system between governments and private companies, it was concluded that it was necessary to discuss it considering the actual state of each country. Importance of recycle and information exchange was realized again. 10 refs., 15 figs., 27 tabs.

  18. FY 1980 Report on results of Sunshine Project. Development of coal liquefaction techniques (Development of materials for the coal liquefaction plant); 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sekitan ekika plant zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    A 1 T/D solvent-extraction type coal liquefaction test plant was constructed and operated to obtain the technical data for the design of, and establish the techniques for, an efficient coal liquefaction plant. The FY 1980 program includes surveys on the materials for coal liquefaction plants, covering those already developed and under development, to clarify the problematical points; drafting the test schedules; and conceptual designs of the material testing facilities. The major problems involved in the materials for coal liquefaction plants include erosion by fluidizing coal slurry, hydrogen embrittlement of the reactor materials, and corrosion by the liquefaction products (e.g., stress-corrosion cracking of austenitic steel, and corrosion by organic acids). The surveys on materials research trends suggest that USA seems to concentrate their research efforts on the reactor materials. The corrosion tests are mostly of in-plant tests, but the stress corrosion and slurry erosion tests are conducted on a laboratory scale. The conceptual designs are drawn for some testing units, e.g., the loop type material testing unit and basic testing unit for jet-spray type slurry erosion. (NEDO)

  19. Ultimate evaluation report on research and development of basic technologies for next-generation industry. Conductive polymeric materials; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saishu kenkyu kaihatsu hyoka. Dodensei kobunshi zairyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-01

    Basic technologies are established that equip polymeric materials (insulators in general) with conductivity similar to that of metals for the realization of novel conducting materials characterized by light weight, high resistance to corrosion, and ease of machining, and for the manufacture of novel electrical/electronic materials having new functions different from those of conventionally used metals. The aims are to realize a conductivity of 10{sup 5}S/cm or more, to manufacture materials sufficiently stable when left in the ordinary or inert atmosphere, and to manufacture materials which may be machined into proper shapes as required in the industry. The results of the 10-year-long development endeavor greatly contribute to the creation of high-level materials, the systematization of technologies, and the elucidation of the conducting mechanism. In relation to polymeric materials, in particular, a new technology is developed that equips, with high reproducibility, polymeric materials with conductivity similar to that of silver or copper; a graphitic material is created for the first time provided with conductivity superior to that of metals; and conducting polymeric materials are equipped with an easy-to-machine feature. A great contribution is accomplished to the production of superconductivity in organic charge-transfer complex crystals and to the elucidation of the conducting mechanism. (NEDO)

  20. R and D project for large industrial technologies in fiscal 1989. Report on achievements in R and D of robots for critical works; 1989 nendo seika hokokusho. Ogata kogyo gijutsu kenkyu kaihatsu jigyo. Kyokugen sagyo robot no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    Research and development have been performed on basic technologies common to different types of robots to carry out works in critical conditions. This paper summarizes the achievements in fiscal 1989. In the R and D of sensor technologies, a prototype tri-axial one-millimeter sensor array and a signal processing device were produced and evaluations were given. A prototype production and evaluations were made on a system that can recognize comprehensively the slip, hardness, and moment as the tri-axial tactile information. In the R and D of motive force technologies, discussions were given on improvement of sensitivity of the torque sensor in the actuator for force control. Design and prototype fabrication were carried out on a speed reducer integrated actuator having a torque sensor for the manipulator's elbow joint. In addition, a force controlled controller was fabricated on a trial basis, which compensates the non-linearity of the force controlled actuator by means of software control. In the R and D of the robot languages, an application program was prepared on a representative work related to movements of a critical work robot. Verification was also conducted on the reasonability of the grammar specifications. (NEDO)

  1. Research and development of basic technologies for the next generation industries, 'environment resistance strengthened elements'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'Taikankyo kyoka soshi'. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-31

    In the research and development of the environment resistance strengthened elements with emphasis placed respectively on radiation resistance, heat resistance, and integration degree according to specific requirements in the using environments, the second term has developed an integration technology and its evaluation technology based on the achievements in the first term. In developing the heat resistant element technology, the technology to grow {beta}-SiC crystals was expanded to obtaining thin film crystals with high migratory performance by using higher temperatures. At the same time, development was performed on a technology to manufacture multiple number of transistors on one substrate, such as the doping technology and etching technology. Using this technology, schottky diodes and p-n junction elements being the basic structures of MES-FET and bipolar transistors were fabricated. In the evaluation and testing technology, the {gamma} dose measuring method using TLD was improved, the traceability of {gamma} ray irradiation amount was assured, the simplified irradiation testing method using X-ray was established, and the heat resistance testing technology for electronic parts was established. Furthermore, attempts were made on enhancing radiation resistance of the elements, such as in MOS silicon integrated circuit, bipolar silicon integrated circuit, and compound semiconductor integrated circuit. (NEDO)

  2. Research and development of basic technologies for next-generation industry. Evaluation of 1st-phase research and development of 3-dimensional circuit devices; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Sanjigen kairo soshi daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The aim is to develop basic technologies relating to 3-dimensional circuit devices with an ultrahigh-density accumulation of functions therein for the embodiment of ultra-small high-performance data processing devices or artificial brain-like multiple-function data processing devices. To be developed are laminate-structure devices which have an ultrahigh-density accumulation of logic and memory functions or a complex accumulation of functions including signal and sensor functions. In the 1st phase, importance is attached to the development of a multilayer crystalline structure, which is the most elementary in the development of 3-dimensional circuit devices, and of processing technologies for them. Propositions are made and analyses are conducted relating to the enlargement of exposure region in synchrotron radiation lithography, development of a maskless beam process of a resolution of 0.1{mu}m, development of a focused ion beam device, etc. Recrystallization methods using a laser beam or a linear electron beam are developed for the growth of multilayer crystals, and are proved to be effective. The application feasibility of a flat deposition dry process etc. to laminate processing technologies is demonstrated. Concerning integration technologies, some laminated circuit devices are experimentally fabricated, and their behavior is determined. The goals of the 1st phase are found achieved. (NEDO)

  3. Industrial science and technology research and development institutions in fiscal 1999. Report on achievements in research and development of human media; 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido. Human media no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to give the society with the full picture of human media at an early time, actual problems in industries were taken up. This paper summarizes the sensitivity agent to support sensitivity of individuals, the human media database, the urban environment human media aiming at symbiosis of nature with artificial environment, and the achievements of comprehensive investigations and researches in fiscals 1999 and 2000. Activities were taken in the following four areas: 1) research and development of the sensitivity agent and human media database, 2) research and development of the urban environment human media, 3) comprehensive investigations and researches, and 4) investigations on technological trends in foreign countries. In Item 1), discussions were given on the technology to present full-color images at high accuracy, the image sensitivity retrieval technology, and the multi-dimensional interface technology for the human media database. In studying the basic human media technology, discussions were given on the basic sensitivity modeling technology, and the sensitivity agent mechanism. (NEDO)

  4. Fiscal 1994 entrusted task report. Surveys of advanced natural gas development and efficient utilization (Survey of coal hydrogasification technology development); 1994 nendo tennen gas kodo kaihatsu yuko riyo chosa tou itaku gyomu hokokusho. Sekitan suiten gaska gijutsu kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    For the establishment of a practical process for substitute natural gas (SNG) production, technological and economical assessments were made, and tasks to discharge for the development were discussed. In this fiscal year, the results of surveys conducted in the past five-year period were compiled, and studies were made to prepare for a smooth transition to the element research stage. Findings obtained are described below. SNG producing technologies need to be developed, with the demand for SNG increasing sharply, to further stabilize the base for SNG supply; coal which is abundantly available should be used as the material for SNG; and coal hydrogasification, among various methods for producing SNG from coal, is the most suitable in view of efficiency and cost performance. It was also found after a prolonged study for the improvement of efficiency and cost performance that probabilities were high that the yield of BTX (benzene, toluene, xylene) would increase and cost performance would improve. Besides, a basic plan and an element technology research plan were prepared for the development of the ARCH (advanced rapid coal hydrogasification) process. (NEDO)

  5. Research and development of basic technologies for the next generation industries, 'three-dimensional circuit elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'sanjigen kairo soshi'. Kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-04-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to three-dimensional circuit elements that integrate functions at ultra-high density. For the basic technology of lamination, the SOI technology suitable for the three-dimensional circuit elements was developed, and it has become possible to manufacture high-quality multi-layered crystalline structure by means of annealing that uses laser and electron beam. In addition, a lateral epitaxial technology for solid phase was developed, and the base to be applied to the three-dimensional circuit elements was established. Furthermore, the technology to put thin film circuits together would be useful for high-density integration in the future. The three-dimensional circuit makes parallel processing in each segment possible, whereas a possibility was shown that the processing can be performed at much higher speed than before. Actually a prototype three-dimensional circuit equipped with functions for parallel processing and judgment processing was fabricated. The image pre-processing which has been impossible on the real time basis in the conventional two-dimensional integrated circuit was realized in a speed as fast as milli-second order. These achievements lead to a belief that the targets for the present research and development have been achieved. (NEDO)