Airborne microorganisms from waste containers.

Science.gov (United States)

Jedlicka, Sabrina S; Stravitz, David M; Lyman, Charles E

2012-01-01

In physician's offices and biomedical labs, biological waste is handled every day. This waste is disposed of in waste containers designed for holding red autoclave bags. The containers used in these environments are closed hands-free containers, often with a step pedal. While these containers protect the user from surface-borne microorganisms, the containers may allow airborne microorganisms to escape via the open/close mechanism because of the air current produced upon open/close cycles. In this study, the air current was shown to be sufficient to allow airborne escape of microorganisms held in the container, including Aspergillus niger. However, bacterial cultures, such as Escherichia coli and Lactococcus lactis did not escape. This may be due to the choice of bacterial cultures and the absence of solid waste, such as dust or other particulate matter in the waste containers, that such strains of bacteria could travel on during aerosolization. We compared these results to those obtained using a re-designed receptacle, which mimimizes air currents, and detected no escaping microorganisms. This study highlights one potential source of airborne contamination in labs, hospitals, and other environments that dispose of biological waste.

Degradation of dome cutting minerals in Hanford waste-13100

International Nuclear Information System (INIS)

Reynolds, Jacob G.; Huber, Heinz J.; Cooke, Gary A.

2013-01-01

At the Hanford Tank Farms, recent changes in retrieval technology require cutting new risers in several single-shell tanks. The Hanford Tank Farm Operator is using water jet technology with abrasive silicate minerals such as garnet or olivine to cut through the concrete and rebar dome. The abrasiveness of these minerals, which become part of the high-level waste stream, may enhance the erosion of waste processing equipment. However, garnet and olivine are not thermodynamically stable in Hanford waste, slowly degrading over time. How likely these materials are to dissolve completely in the waste before the waste is processed in the Waste Treatment and Immobilization Plant can be evaluated using theoretical analysis for olivine and collected direct experimental evidence for garnet. Based on an extensive literature study, a large number of primary silicates decompose into sodalite and cancrinite when exposed to Hanford waste. Given sufficient time, the sodalite also degrades into cancrinite. Even though cancrinite has not been directly added to any Hanford tanks during process times, it is the most common silicate observed in current Hanford waste. By analogy, olivine and garnet are expected to ultimately also decompose into cancrinite. Garnet used in a concrete cutting demonstration was immersed in a simulated supernate representing the estimated composition of the liquid retrieving waste from Hanford tank 241-C-107 at both ambient and elevated temperatures. This simulant was amended with extra NaOH to determine if adding caustic would help enhance the degradation rate of garnet. The results showed that the garnet degradation rate was highest at the highest NaOH concentration and temperature. At the end of 12 weeks, however, the garnet grains were mostly intact, even when immersed in 2 molar NaOH at 80 deg C. Cancrinite was identified as the degradation product on the surface of the garnet grains. In the case of olivine, the rate of degradation in the high-pH regimes

Degradation of Dome Cutting Minerals in Hanford Waste - 13100

Energy Technology Data Exchange (ETDEWEB)

Reynolds, Jacob G.; Cooke, Gary A.; Huber, Heinz J. [Washington River Protection Solutions, LLC, P.O. Box 850, Richland, WA 99352 (United States)

2013-07-01

At the Hanford Tank Farms, recent changes in retrieval technology require cutting new risers in several single-shell tanks. The Hanford Tank Farm Operator is using water jet technology with abrasive silicate minerals such as garnet or olivine to cut through the concrete and rebar dome. The abrasiveness of these minerals, which become part of the high-level waste stream, may enhance the erosion of waste processing equipment. However, garnet and olivine are not thermodynamically stable in Hanford waste, slowly degrading over time. How likely these materials are to dissolve completely in the waste before the waste is processed in the Waste Treatment and Immobilization Plant can be evaluated using theoretical analysis for olivine and collected direct experimental evidence for garnet. Based on an extensive literature study, a large number of primary silicates decompose into sodalite and cancrinite when exposed to Hanford waste. Given sufficient time, the sodalite also degrades into cancrinite. Even though cancrinite has not been directly added to any Hanford tanks during process times, it is the most common silicate observed in current Hanford waste. By analogy, olivine and garnet are expected to ultimately also decompose into cancrinite. Garnet used in a concrete cutting demonstration was immersed in a simulated supernate representing the estimated composition of the liquid retrieving waste from Hanford tank 241-C-107 at both ambient and elevated temperatures. This simulant was amended with extra NaOH to determine if adding caustic would help enhance the degradation rate of garnet. The results showed that the garnet degradation rate was highest at the highest NaOH concentration and temperature. At the end of 12 weeks, however, the garnet grains were mostly intact, even when immersed in 2 molar NaOH at 80 deg. C. Cancrinite was identified as the degradation product on the surface of the garnet grains. In the case of olivine, the rate of degradation in the high

Reactions of metal oxides with molten NaPO3 + NaCl mixtures

International Nuclear Information System (INIS)

Kovarskaya, E.N.; Mityakhina, V.S.; Rodionov, Yu.I.; Silin, M.Yu.

1988-01-01

We consider the dissolution mechanism for iron (III), europium(III), and tin(IV) oxides in molten NaPO 3 + NaCl that are responsible for the peak solubilities. We chose Fe 2 O 3 as the basic material since this occurs in large amounts around damaged metal structures in rock salt mines in a proposed zone for storing vitrified radioactive wastes. Solubility measurement and paper chromatography show that Fe 2 O 3 dissolves in molten NaPO 3 + NaCl in air by reaction with the solvent to give double iron and sodium diphosphates and monophosphates in accordance with the initial solution-in-the-melt composition, the degree of equilibration, and the temperature. The elevated solubilities for initial NaCl contents close to 30 mole % are due to sodium triphosphates and tricyclophosphates present in these melts. Moessbauer spectroscopy confirms that double iron, europium and tin diphosphates and monophosphates containing sodium occur in these chloride-polyphosphate melts

High integrity container evaluation for solid waste disposal burial containers

International Nuclear Information System (INIS)

Josephson, W.S.

1996-01-01

In order to provide radioactive waste disposal practices with the greatest measure of public protection, Solid Waste Disposal (SWD) adopted the Nuclear Regulatory Commission (NRC) requirement to stabilize high specific activity radioactive waste prior to disposal. Under NRC guidelines, stability may be provided by several mechanisms, one of which is by placing the waste in a high integrity container (HIC). During the implementation process, SWD found that commercially-available HICs could not accommodate the varied nature of weapons complex waste, and in response developed a number of disposal containers to function as HICs. This document summarizes the evaluation of various containers that can be used for the disposal of Category 3 waste in the Low Level Burial Grounds. These containers include the VECTRA reinforced concrete HIC, reinforced concrete culvert, and the reinforced concrete vault. This evaluation provides justification for the use of these containers and identifies the conditions for use of each

1994 Solid waste forecast container volume summary

International Nuclear Information System (INIS)

Templeton, K.J.; Clary, J.L.

1994-09-01

This report describes a 30-year forecast of the solid waste volumes by container type. The volumes described are low-level mixed waste (LLMW) and transuranic/transuranic mixed (TRU/TRUM) waste. These volumes and their associated container types will be generated or received at the US Department of Energy Hanford Site for storage, treatment, and disposal at Westinghouse Hanford Company's Solid Waste Operations Complex (SWOC) during a 30-year period from FY 1994 through FY 2023. The forecast data for the 30-year period indicates that approximately 307,150 m 3 of LLMW and TRU/TRUM waste will be managed by the SWOC. The main container type for this waste is 55-gallon drums, which will be used to ship 36% of the LLMW and TRU/TRUM waste. The main waste generator forecasting the use of 55-gallon drums is Past Practice Remediation. This waste will be generated by the Environmental Restoration Program during remediation of Hanford's past practice sites. Although Past Practice Remediation is the primary generator of 55-gallon drums, most waste generators are planning to ship some percentage of their waste in 55-gallon drums. Long-length equipment containers (LECs) are forecasted to contain 32% of the LLMW and TRU/TRUM waste. The main waste generator forecasting the use of LECs is the Long-Length Equipment waste generator, which is responsible for retrieving contaminated long-length equipment from the tank farms. Boxes are forecasted to contain 21% of the waste. These containers are primarily forecasted for use by the Environmental Restoration Operations--D ampersand D of Surplus Facilities waste generator. This waste generator is responsible for the solid waste generated during decontamination and decommissioning (D ampersand D) of the facilities currently on the Surplus Facilities Program Plan. The remaining LLMW and TRU/TRUM waste volume is planned to be shipped in casks and other miscellaneous containers

Remote automatic control scheme for plasma arc cutting of contaminated waste

International Nuclear Information System (INIS)

Dudar, A.M.; Ward, C.R.; Kriikku, E.M.

1993-01-01

The Robotics Development Group at the Savannah River Technology Center has developed and implemented a scheme to perform automatic cutting of metallic contaminated waste. The scheme employs a plasma arc cutter in conjunction with a laser ranging sensor attached to a robotic manipulator called the Telerobot. A software algorithm using proportional control is then used to perturb the robot's trajectory in such a way as to regulate the plasma arc standoff and the robot's speed in order to achieve automatic plasma arc cuts. The scheme has been successfully tested on simulated waste materials and the results have been very favorable. This report details the development and testing of the scheme

Passivity of alloy C-22 in NaCl solutions

International Nuclear Information System (INIS)

Rodriguez, Martin A.; Carranza, Ricardo M.

2004-01-01

Alloy C-22 has been proposed as the corrosion resistant barrier of high-level waste nuclear containers. This alloy must be resistant to corrosion in multi-ionic solutions for a period of time as long as 10,000 years. The aim of the present work was to study the corrosion behavior of alloy C-22 in NaCl solutions. General and crevice corrosion were studied by means of electrochemical techniques. Open circuit potential was measured over the time, electrochemical impedance spectroscopy (EIS) measurements were carried out at open circuit and passivity potentials, as well as cyclic potentiodynamic polarization curves. Corrosion rates obtained by EIS measurements were acceptable for a waste nuclear container ( P ) values increased with open circuit potential and polarization time at constant potential. This was attributed to an increase in oxide film thickness and its aging respectively. The passive oxide form on alloy C-22 at the studied conditions presented a n-type semiconductor behavior in the passive potential range. Repassivation potential values (E R1 ) were determined for alloy C-22 at the studied conditions using PCA probes. (author) [es

Self-Contained Cross-Cutting Pipeline Software Architecture

OpenAIRE

Patwardhan, Amol; Patwardhan, Rahul; Vartak, Sumalini

2016-01-01

Layered software architecture contains several intra-layer and inter-layer dependencies. Each layer depends on shared components making it difficult to release a code change, bug fix or feature without exhaustive testing and having to build the entire software code base. This paper proposed self-contained, cross-cutting pipeline architecture (SCPA) that is independent of existing layers. We chose 2 open source projects and 3 internal intern projects that used n-tier architecture and applied t...

Vertical cut-off walls for the containment of contaminated ground

International Nuclear Information System (INIS)

Jessberger, H.L.; Krubasik, K.; Beine, R.A.

1997-01-01

Vertical cut-off walls are widely used for the containment of contaminated sites, where a capping system is not sufficient for the protection of groundwater. Various types of cut-off walls are introduced and new developments are prescribed. Design and testing principles are outlined. Containment techniques are the appropriate measure for old landfills and abandoned industrial sites with contaminated ground and groundwater, too, since the shortage of financial resources in many countries classifies clean-up techniques as too cost intensive in most cases

Alternative containers for low-level wastes containing large amounts of tritium

International Nuclear Information System (INIS)

Gause, E.P.; Lee, B.S.; MacKenzie, D.R.; Wiswall, R. Jr.

1984-11-01

High-activity tritiated waste generated in the United States is mainly composed of tritium gas and tritium-contaminated organic solvents sorbed onto Speedi-Dri which are packaged in small glass bulbs. Low-activity waste consists of solidified and adsorbed liquids. In this report, current packages for high-activity gaseous and low-activity adsorbed liquid wastes are emphasized with regard to containment potential. Containers for low-level radioactive waste containing large amounts of tritium need to be developed. An integrity may be threatened by: physical degradation due to soil corrosion, gas pressure build-up (due to radiolysis and/or biodegradation), rapid permeation of tritium through the container, and corrosion from container contents. Literature available on these points is summarized in this report. 136 references, 20 figures, 40 tables

Multipurpose container for low-level radioactive waste

International Nuclear Information System (INIS)

Anderson, R.T.; Pearson, S.D.

1993-01-01

A method is described for disposing of low-level radioactive waste, comprising the steps of (a) introducing the waste into a multipurpose container, the multipurpose container comprising a polymeric inner container disposed within a concrete outer shell, the shape of the inner container conforming substantially to the shape of the outer shell's inner surface, (b) transporting the waste in the same multipurpose container to a storage location, and (c) storing the container at the storage location

Inhibition of acid mine drainage and immobilization of heavy metals from copper flotation tailings using a marble cutting waste

Science.gov (United States)

Tozsin, Gulsen

2016-01-01

Acid mine drainage (AMD) with high concentrations of sulfates and metals is generated by the oxidation of sulfide bearing wastes. CaCO3-rich marble cutting waste is a residual material produced by the cutting and polishing of marble stone. In this study, the feasibility of using the marble cutting waste as an acid-neutralizing agent to inhibit AMD and immobilize heavy metals from copper flotation tailings (sulfide- bearing wastes) was investigated. Continuous-stirring shake-flask tests were conducted for 40 d, and the pH value, sulfate content, and dissolved metal content of the leachate were analyzed every 10 d to determine the effectiveness of the marble cutting waste as an acid neutralizer. For comparison, CaCO3 was also used as a neutralizing agent. The average pH value of the leachate was 2.1 at the beginning of the experiment ( t = 0). In the experiment employing the marble cutting waste, the pH value of the leachate changed from 6.5 to 7.8, and the sulfate and iron concentrations decreased from 4558 to 838 mg/L and from 536 to 0.01 mg/L, respectively, after 40 d. The marble cutting waste also removed more than 80wt% of heavy metals (Cd, Cr, Cu, Ni, Pb, and Zn) from AMD generated by copper flotation tailings.

Nuclear waste storage container with metal matrix

Science.gov (United States)

Sump, Kenneth R.

1978-01-01

The invention relates to a storage container for high-level waste having a metal matrix for the high-level waste, thereby providing greater impact strength for the waste container and increasing heat transfer properties.

Nuclear waste storage container with metal matrix

International Nuclear Information System (INIS)

Sump, K.R.

1978-01-01

The invention relates to a storage container for high-level waste having a metal matrix for the high-level waste, thereby providing greater impact strength for the waste container and increasing heat transfer properties

Network Design for Container Shipping Using Cutting Planes

DEFF Research Database (Denmark)

The network design problem in container shipping is of increasing importance in the strongly competitive markets where potential cost reductions are of the utmost importance. We combine the network design and fleet assignment problem into a mixed integer linear programming model minimizing the ov...... the fact that the route of a ship allows for subtours, we introduce the concept of pseudo-simple routes. To solve the problem we use a branch and cut solution method using clover and capacity cuts we defined for the problem.......The network design problem in container shipping is of increasing importance in the strongly competitive markets where potential cost reductions are of the utmost importance. We combine the network design and fleet assignment problem into a mixed integer linear programming model minimizing...... the overall cost. The real-life container shipping network design problem differs in several ways from the standard network design problem. Examples of these differences are the cyclic routes of vessels and the fact that a route is continuously sailed for a given forecast period. To model these real...

Method for processing radioactive wastes containing sodium

International Nuclear Information System (INIS)

Kubota, Takeshi.

1975-01-01

Object: To bake, solidify and process even radioactive wastes highly containing sodium. Structure: H and or NH 4 zeolites of more than 90g per chemical equivalent of sodium present in the waste is added to and left in radioactive wastes containing sodium, after which they are fed to a baker such as rotary cylindrical baker, spray baker and the like to bake and solidify the wastes at 350 to 800 0 C. Thereby, it is possible to bake and solidify even radioactive wastes highly containing sodium, which has been impossible to do so previously. (Kamimura, M.)

Cermets for high level waste containment

International Nuclear Information System (INIS)

Aaron, W.S.; Quinby, T.C.; Kobisk, E.H.

1978-01-01

Cermet materials are currently under investigation as an alternate for the primary containment of high level wastes. The cermet in this study is an iron--nickel base metal matrix containing uniformly dispersed, micron-size fission product oxides, aluminosilicates, and titanates. Cermets possess high thermal conductivity, and typical waste loading of 70 wt % with volume reduction factors of 2 to 200 and low processing volatility losses have been realized. Preliminary leach studies indicate a leach resistance comparable to other candidate waste forms; however, more quantitative data are required. Actual waste studies have begun on NFS Acid Thorex, SRP dried sludge and fresh, unneutralized SRP process wastes

Defense High Level Waste Disposal Container System Description Document

International Nuclear Information System (INIS)

2000-01-01

The Defense High Level Waste Disposal Container System supports the confinement and isolation of waste within the Engineered Barrier System of the Monitored Geologic Repository (MGR). Disposal containers are loaded and sealed in the surface waste handling facilities, transferred to the underground through the accesses using a rail mounted transporter, and emplaced in emplacement drifts. The defense high level waste (HLW) disposal container provides long-term confinement of the commercial HLW and defense HLW (including immobilized plutonium waste forms (IPWF)) placed within disposable canisters, and withstands the loading, transfer, emplacement, and retrieval loads and environments. U.S. Department of Energy (DOE)-owned spent nuclear fuel (SNF) in disposable canisters may also be placed in a defense HLW disposal container along with commercial HLW waste forms, which is known as 'co-disposal'. The Defense High Level Waste Disposal Container System provides containment of waste for a designated period of time, and limits radionuclide release. The disposal container/waste package maintains the waste in a designated configuration, withstands maximum handling and rockfall loads, limits the individual canister temperatures after emplacement, resists corrosion in the expected handling and repository environments, and provides containment of waste in the event of an accident. Defense HLW disposal containers for HLW disposal will hold up to five HLW canisters. Defense HLW disposal containers for co-disposal will hold up to five HLW canisters arranged in a ring and one DOE SNF canister in the ring. Defense HLW disposal containers also will hold two Multi-Canister Overpacks (MCOs) and two HLW canisters in one disposal container. The disposal container will include outer and inner cylinders, outer and inner cylinder lids, and may include a canister guide. An exterior label will provide a means by which to identify the disposal container and its contents. Different materials

Methane from waste containing paper

Energy Technology Data Exchange (ETDEWEB)

1981-12-24

Waste solids containing paper are biologically treated in a system by: fermentation with lactobacilli, separation of the solids, ion exchange of the supernatant from the separation, anaerobic digestion of the ion-exchanged liquor, separation of a liquor from the fermentation, and digestion of the liquor. Thus, a municipal waste containing paper and water was inoculated with Aspergillus niger and lactobacilli for 2 days; the mixture was anaerobically treated and centrifuged; the clear liquor was ion exchanged; and the solid waste was filter pressed. The filter cake was treated with Trichoderma nigricaus and filtered. The filtrate and the ion-exchanged liquor were digested for CH/sub 4/ production.

Evaluation on radioactive waste disposal amount of Kori Unit 1 reactor vessel considering cutting and packaging methods

International Nuclear Information System (INIS)

Choi, Yu Jong; Lee, Seong Cheol; Kim, Chang Lak

2016-01-01

Decommissioning of nuclear power plants has become a big issue in South Korea as some of the nuclear power plants in operation including Kori unit 1 and Wolsung unit 1 are getting old. Recently, Wolsung unit 1 received permission to continue operation while Kori unit 1 will shut down permanently in June 2017. With the consideration of segmentation method and disposal containers, this paper evaluated final disposal amount of radioactive waste generated from decommissioning of the reactor pressure vessel in Kori unit 1 which will be decommissioned as the first in South Korea. The evaluation results indicated that the final disposal amount from the top and bottom heads of the reactor pressure vessel with hemisphere shape decreased as they were cut in smaller more effectively than the cylindrical part of the reactor pressure vessel. It was also investigated that 200 L and 320 L radioactive waste disposal containers used in Kyung-Ju disposal facility had low payload efficiency because of loading weight limitation

Crystallographic characterization of cement pastes hydrated with NaCl; Caracterizacao cristalografica de pastas de cimento hidratadas com NaCl

Energy Technology Data Exchange (ETDEWEB)

Melo, Carina Gabriela de Melo e; Martinelli, Antonio Eduardo; Melo, Dulce Maria Araujo; Melo, Marcus Antonio de Freitas; Melo, Vitor Rodrigo de Melo e [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

2012-07-01

One of the major current challenges faced by oil companies is the exploration of pre salt basins. Salt layers deposited upon the evaporation of ocean water and continental separation are mainly formed by NaCl and isolate immense oil reservoirs. The mechanical stability and zonal isolation of oil wells that run through salt layers must be fulfilled by cement sheaths saturated with NaCl to assure chemical compatibility between cement and salt layer. The present study aimed at evaluating the effect of NaCl addition on the hydration of oil well cement slurries as well as identifying the nature of crystalline phases present in the hardened cement. To that end, cement slurries containing NaCl were mixed, hardened and characterized by X-ray diffraction. The results revealed that the presence of NaCl affects the formation of hydration products by the presence of Friedel's salt. The intensity of the corresponding peaks increase as the contents of NaCl in the slurry increase. High concentrations of NaCl in Portland slurries increase the setting time of cement and the presence of Friedel's salt decreases the strength of the hardened cement. (author)

Development of polymer concrete radioactive waste management containers

Energy Technology Data Exchange (ETDEWEB)

Chung, H.; Lee, M. S.; Ahn, D. H.; Won, H. J.; Kang, H. S.; Lee, H. S.; Lim, S.P.; Kim, Y. E.; Lee, B. O.; Lee, K. P.; Min, B. Y.; Lee, J.K.; Jang, W. S.; Sim, W. B.; Lee, J. C.; Park, M. J.; Choi, Y. J.; Shin, H. E.; Park, H. Y.; Kim, C. Y

1999-11-01

A high-integrity radioactive waste container has been developed to immobilize the spent resin wastes from nuclear power plants, protect possible future, inadvertent intruders from damaging radiation. The polymer concrete container is designed to ensure safe and reliable disposal of the radioactive waste for a minimum period of 300 years. A built-in vent system for each container will permit the release of gas. An experimental evaluation of the mechanical, chemical, and biological tests of the container was carried out. The tests showed that the polymer concrete container is adequate for safe disposal of the radioactive wastes. (author)

Defense High Level Waste Disposal Container System Description Document

International Nuclear Information System (INIS)

Pettit, N. E.

2001-01-01

The Defense High Level Waste Disposal Container System supports the confinement and isolation of waste within the Engineered Barrier System of the Monitored Geologic Repository (MGR). Disposal containers are loaded and sealed in the surface waste handling facilities, transferred to the underground through the accesses using a rail mounted transporter, and emplaced in emplacement drifts. The defense high level waste (HLW) disposal container provides long-term confinement of the commercial HLW and defense HLW (including immobilized plutonium waste forms [IPWF]) placed within disposable canisters, and withstands the loading, transfer, emplacement, and retrieval loads and environments. US Department of Energy (DOE)-owned spent nuclear fuel (SNF) in disposable canisters may also be placed in a defense HLW disposal container along with commercial HLW waste forms, which is known as co-disposal. The Defense High Level Waste Disposal Container System provides containment of waste for a designated period of time, and limits radionuclide release. The disposal container/waste package maintains the waste in a designated configuration, withstands maximum handling and rockfall loads, limits the individual canister temperatures after emplacement, resists corrosion in the expected handling and repository environments, and provides containment of waste in the event of an accident. Defense HLW disposal containers for HLW disposal will hold up to five HLW canisters. Defense HLW disposal containers for co-disposal will hold up to five HLW canisters arranged in a ring and one DOE SNF canister inserted in the center and/or one or more DOE SNF canisters displacing a HLW canister in the ring. Defense HLW disposal containers also will hold two Multi-Canister Overpacks (MCOs) and two HLW canisters in one disposal container. The disposal container will include outer and inner cylinders, outer and inner cylinder lids, and may include a canister guide. An exterior label will provide a means by

Radioactive waste processing container

International Nuclear Information System (INIS)

Ishizaki, Kanjiro; Koyanagi, Naoaki; Sakamoto, Hiroyuki; Uchida, Ikuo.

1992-01-01

A radioactive waste processing container used for processing radioactive wastes into solidification products suitable to disposal such as underground burying or ocean discarding is constituted by using cements. As the cements, calcium sulfoaluminate clinker mainly comprising calcium sulfoaluminate compound; 3CaO 3Al 2 O 3 CaSO 4 , Portland cement and aqueous blast furnace slug is used for instance. Calciumhydroxide formed from the Portland cement is consumed for hydration of the calcium sulfoaluminate clinker. According, calcium hydroxide is substantially eliminated in the cement constituent layer of the container. With such a constitution, damages such as crackings and peelings are less caused, to improve durability and safety. (I.N.)

Stem Cuttings as a Quick In Vitro Screening Method of Sodium Chloride Tolerance in Potato (Solanum) Genotypes

International Nuclear Information System (INIS)

Elhag, A. Z.; Mix-Wagnar, G.; Elbassam, N.; Horst, W.

2008-01-01

This study was conducted to find how far in vitro explants stem cuttings technique could be suitable for quick screening of NaCl tolerance solanum genotypes and to identify some aspects of their NaCl tolerance. Fifteen solanum genotypes were tested on four NaCl concentrations both in vitro and in vivo, two-node stem cuttings of in vitro produced explants were grown on Murashige and Skoog (MS) salts supplemented with four NaCl concentrations (0,40,80 and 120 mM) for six weeks in vitro. The other part of the in vitro grown explants were transplanted in Kick- Brauck- Manns pots containing sandy loam soil supplemented also with four NaCl concentration (0, 0.1, 0.2 and 0.3 NaCl, w/w) and grown further either for eight weeks or till harvest in a green house. Both experiments were in a completely randomized design with four replicates. The main stem length, shoot dry matter and tuber yield as well as mineral element (Na''+, K + , Ca''2''+ and Cl''-) were measured. The growth of all genotypes was affected by increasing of NaCl. There was a close correlation between growth response (length of explant main stem) in vitro and shoot dry matter and tuber yield in vivo (r=0.81** for dry matter and 0.72** for tuber yield. Na''+ and Cl''- concentrations in shoots wee inversely correlated with the vegetative growth (r=-0.73** for both in vitro and r=-0.89** and r=-0.88** in vivo, respectively). The genotypes showed varied ability to reduce the transport of Na''+ and Cl''- to the shoots, where by NaCl tolerant genotypes showed lower content of both elements than the sensitive ones. K''+ and Ca''2''+ concentrations were decreased with increasing NaCl concentration. The responses for mineral element (Na''+ and Cl - ) accumulation or restriction of explants in vitro and intact plants in vivo were also closely correlated (r=0.79** and 0.71**, respectively) especially at the medium NaCl concentrations (80 mM and 0.2% NaCl). The similar response of the explant and the intact plant

Assessing the disposal of wastes containing NORM in nonhazardous waste landfills

International Nuclear Information System (INIS)

Smith, K. P.; Blunt, D. L.; Williams, G. P.; Arnish, J. J.; Pfingston, M. R.; Herbert, J.

1999-01-01

In the past few years, many states have established specific regulations for the management of petroleum industry wastes containing naturally occurring radioactive material (NORM) above specified thresholds. These regulations have limited the number of disposal options available for NORM-containing wastes, thereby increasing the related waste management costs. In view of the increasing economic burden associated with NORM management, industry and regulators are interested in identifying cost-effective disposal alternatives that still provide adequate protection of human health and the environment. One such alternative being considered is the disposal of NORM-containing wastes in landfills permitted to accept only nonhazardous wastes. The disposal of petroleum industry wastes containing radium-226 and lead-210 above regulated levels in nonhazardous landfills was modeled to evaluate the potential radiological doses and associated health risks to workers and the general public. A variety of scenarios were considered to evaluate the effects associated with the operational phase (i.e., during landfill operations) and future use of the landfill property. Doses were calculated for the maximally exposed receptor for each scenario. This paper presents the results of that study and some conclusions and recommendations drawn from it

Waste classifying and separation device

International Nuclear Information System (INIS)

Kakiuchi, Hiroki.

1997-01-01

A flexible plastic bags containing solid wastes of indefinite shape is broken and the wastes are classified. The bag cutting-portion of the device has an ultrasonic-type or a heater-type cutting means, and the cutting means moves in parallel with the transferring direction of the plastic bags. A classification portion separates and discriminates the plastic bag from the contents and conducts classification while rotating a classification table. Accordingly, the plastic bag containing solids of indefinite shape can be broken and classification can be conducted efficiently and reliably. The device of the present invention has a simple structure which requires small installation space and enables easy maintenance. (T.M.)

Treatment for hydrazine-containing waste water solution

Science.gov (United States)

Yade, N.

1986-01-01

The treatment for waste solutions containing hydrazine is presented. The invention attempts oxidation and decomposition of hydrazine in waste water in a simple and effective processing. The method adds activated charcoal to waste solutions containing hydrazine while maintaining a pH value higher than 8, and adding iron salts if necessary. Then, the solution is aerated.

Growth of eucalyptus rooted cuttings in toxic organic waste compost of textile industry

Directory of Open Access Journals (Sweden)

Priscila F. de Souza

2015-09-01

Full Text Available ABSTRACTBiodegradation techniques may help contaminated organic wastes to become useful for plant production. The current study aimed to evaluate the efficiency of composting in the biodegradation of toxic residues from the textile industry and its use as substrate in saplings production. Cotton cloths contaminated with oil and grease, used in loom maintenance, were composted in a mixture with cattle manure. The composted material replaced coconut fiber in the substrate for the production of eucalyptus rooted cuttings: mixture of vermiculite, carbonized rice husk and coconut fiber in the ratio of 2:1:1 (v/v and using it as control. Thus, the amount of rice husks remained unchanged and the amount of vermiculite and compost varied. The compost proportion in the tested substrates were 0, 19, 37, 56 and 75%. The compost produced from textile wastes showed high nutrient levels and low levels of heavy metals. In general, the survival, growth and some growth indices of rooted cuttings produced on substrates with 19 and 37% compost were similar to those of rooted cuttings grown in commercial substrate. Composting is efficient and the material is useful for rooted cuttings production.

Waste container weighing data processing to create reliable information of household waste generation.

Science.gov (United States)

Korhonen, Pirjo; Kaila, Juha

2015-05-01

Household mixed waste container weighing data was processed by knowledge discovery and data mining techniques to create reliable information of household waste generation. The final data set included 27,865 weight measurements covering the whole year 2013 and it was selected from a database of Helsinki Region Environmental Services Authority, Finland. The data set contains mixed household waste arising in 6m(3) containers and it was processed identifying missing values and inconsistently low and high values as errors. The share of missing values and errors in the data set was 0.6%. This provides evidence that the waste weighing data gives reliable information of mixed waste generation at collection point level. Characteristic of mixed household waste arising at the waste collection point level is a wide variation between pickups. The seasonal variation pattern as a result of collective similarities in behaviour of households was clearly detected by smoothed medians of waste weight time series. The evaluation of the collection time series against the defined distribution range of pickup weights on the waste collection point level shows that 65% of the pickups were from collection points with optimally dimensioned container capacity and the collection points with over- and under-dimensioned container capacities were noted in 9.5% and 3.4% of all pickups, respectively. Occasional extra waste in containers occurred in 21.2% of the pickups indicating the irregular behaviour of individual households. The results of this analysis show that processing waste weighing data using knowledge discovery and data mining techniques provides trustworthy information of household waste generation and its variations. Copyright © 2015 Elsevier Ltd. All rights reserved.

Nano-sized precipitated formations in irradiated NaCl

NARCIS (Netherlands)

Sugonyako, Anton V.

2007-01-01

The interest in the formation of radiation damage in alkali halides and in particular, in NaCl, is stimulated by the fact that rock-salt in stable geological formations is a prominent candidate medium for storage of high-level waste (HLW) of nuclear power plants. Since the 1950s, scientists and

Treatment of mercury containing waste

Science.gov (United States)

Kalb, Paul D.; Melamed, Dan; Patel, Bhavesh R; Fuhrmann, Mark

2002-01-01

A process is provided for the treatment of mercury containing waste in a single reaction vessel which includes a) stabilizing the waste with sulfur polymer cement under an inert atmosphere to form a resulting mixture and b) encapsulating the resulting mixture by heating the mixture to form a molten product and casting the molten product as a monolithic final waste form. Additional sulfur polymer cement can be added in the encapsulation step if needed, and a stabilizing additive can be added in the process to improve the leaching properties of the waste form.

Earthworms as bio-indicators of chemical pollution in soils with drilling waste

Directory of Open Access Journals (Sweden)

Kujawska Justyna

2017-01-01

Full Text Available The deposited drilling waste may alter the functioning of soil ecosystems by disrupting the soil fauna. The wastes contain toxic compounds such as metals or hydrocarbons, which tend to accumulate in the living. In the research, earthworms were used u as bio-indicators of soil pollution resulting from the presence of pollution contained in drilling waste. The aim of this study is to evaluation of toxicity of the waste of spent oil and water drilling cuttings to earthworm Eisenia fetida. Oil-based and water-based drilling cuttings were added to soil, used six doses of drilling wastes (5%, 10%, 15%, 25%, 30%, 50%. The results showed that the 45 days LC50 of oil-based drilling cuttings ranged 18%, LC50 of water-based drilling cuttings ranged 33%. In general, mortality increases with increasing dosage waste.

NEW CRITERIA FOR ASSIGNING WASTE CONTAINING TECH-NOGENIC RADIONUCLIDES TO THE RADIOACTIVE WASTE

Directory of Open Access Journals (Sweden)

I. K. Romanovich

2010-01-01

Full Text Available The article contains detailed description of criteria for assigning of liquid and gaseous industrial waste containing technogenicradionuclides to the radioactive waste, presented in the new Basic Sanitary Rulesof Radiation Safety (OSPORB-99/2010. The analysisof shortcomings and discrepancies of the previously used in Russia system of criteria for assigning waste to the radioactive waste is given.

Characterization of Hanford tank wastes containing ferrocyanides

International Nuclear Information System (INIS)

Tingey, J.M.; Matheson, J.D.; McKinley, S.G.; Jones, T.E.; Pool, K.H.

1993-02-01

Currently, 17 storage tanks on the Hanford site that are believed to contain > 1,000 gram moles (465 lbs) of ferrocyanide compounds have been identified. Seven other tanks are classified as ferrocyanide containing waste tanks, but contain less than 1,000 gram moles of ferrocyanide compounds. These seven tanks are still included as Hanford Watch List Tanks. These tanks have been declared an unreviewed safety question (USQ) because of potential thermal reactivity hazards associated with the ferrocyanide compounds and nitrate and nitrite. Hanford tanks with waste containing > 1,000 gram moles of ferrocyanide have been sampled. Extensive chemical, radiothermical, and physical characterization have been performed on these waste samples. The reactivity of these wastes were also studied using Differential Scanning Calorimetry (DSC) and Thermogravimetric analysis. Actual tank waste samples were retrieved from tank 241-C-112 using a specially designed and equipped core-sampling truck. Only a small portion of the data obtained from this characterization effort will be reported in this paper. This report will deal primarily with the cyanide and carbon analyses, thermal analyses, and limited physical property measurements

Alternatives for high-level waste forms, containers, and container processing systems

International Nuclear Information System (INIS)

Crawford, T.W.

1995-01-01

This study evaluates alternatives for high-level waste forms, containers, container processing systems, and onsite interim storage. Glass waste forms considered are cullet, marbles, gems, and monolithic glass. Small and large containers configured with several combinations of overpack confinement and shield casks are evaluated for these waste forms. Onsite interim storage concepts including canister storage building, bore holes, and storage pad were configured with various glass forms and canister alternatives. All favorable options include the monolithic glass production process as the waste form. Of the favorable options the unshielded 4- and 7-canister overpack options have the greatest technical assurance associated with their design concepts due to their process packaging and storage methods. These canisters are 0.68 m and 0.54 m in diameter respectively and 4.57 m tall. Life-cycle costs are not a discriminating factor in most cases, varying typically less than 15 percent

Air-tight disposing device for solid radioactive waste

International Nuclear Information System (INIS)

Aoyama, Saburo.

1976-01-01

Object: In a construction for air-tightly connecting radioactive material handling equipment with a radioactive waste container through a vinyl bag, to use a multi-stage expansion tube to introduce the radioactive waste into the waste container in safe and positive manner. Structure: During normal operation in the radioactive material handling equipment, a multi-stage expansion cylinder is extended by operation of a remote shaft to suitably throw the waste in a state with a vinyl bag protected, whereas when the waste is disposed away from the equipment, the multi-stage expansion cylinder is contracted and received into a holder, and the vinyl bag is heated and sealed at a given position and cut, after which a cover of an outer container for disposal is closed and carried out. The vinyl bag remained on the side of the holder after sealed and cut is put into the waste container after a fresh vinyl bag, in which another waste container is received, has been secured to the holder. (Taniai, N.)

Designing Advanced Ceramic Waste Forms for Electrochemical Processing Salt Waste

International Nuclear Information System (INIS)

Ebert, W. L.; Snyder, C. T.; Frank, Steven; Riley, Brian

2016-01-01

loading from about 12% to 10% on a mass basis, but this will not significantly impact the waste loading on a volume basis. It is likely that heat output will limit the amount of waste salt that can be accommodated in a waste canister rather than the salt loading in an ACWF, and that the increase from 8 mass% to about 10 mass% salt loadings in ACWF materials will be sufficient to optimize these waste forms. Although the waste salt composition used in this study contained a moderate amount of NaCl, the test results suggest waste salts with little or no NaCl can be accommodated in ACWF materials by using the new binder glass, albeit at waste loadings lower than 8 mass%. The higher glass contents that will be required for ACWF materials made with salt wastes that do not contain NaCl are expected to result in much lower porosities in those waste forms.

Designing Advanced Ceramic Waste Forms for Electrochemical Processing Salt Waste

Energy Technology Data Exchange (ETDEWEB)

Ebert, W. L. [Argonne National Lab. (ANL), Argonne, IL (United States); Snyder, C. T. [Argonne National Lab. (ANL), Argonne, IL (United States); Frank, Steven [Argonne National Lab. (ANL), Argonne, IL (United States); Riley, Brian [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-03-01

the waste loading from about 12% to 10% on a mass basis, but this will not significantly impact the waste loading on a volume basis. It is likely that heat output will limit the amount of waste salt that can be accommodated in a waste canister rather than the salt loading in an ACWF, and that the increase from 8 mass% to about 10 mass% salt loadings in ACWF materials will be sufficient to optimize these waste forms. Although the waste salt composition used in this study contained a moderate amount of NaCl, the test results suggest waste salts with little or no NaCl can be accommodated in ACWF materials by using the new binder glass, albeit at waste loadings lower than 8 mass%. The higher glass contents that will be required for ACWF materials made with salt wastes that do not contain NaCl are expected to result in much lower porosities in those waste forms.

Iron recovery from the waste generated during the cutting of granite

International Nuclear Information System (INIS)

Junca, E.; Espinosa, D. C. R.; Tenorio, J. A. S.; De Oliveira, J. R.

2015-01-01

Metallic iron is present in the waste left when granite blocks are cut. Thus, the purpose of this study was to characterize this waste using chemical and particle size analyses. To achieve this, X-ray diffraction and scanning electron microscopy coupled with electron back-scattered diffraction were used. To find the method with the best metallic iron recovery from the waste of ornamental rock, three distinct methods were examined: magnetic separation, table concentration and cyclone processing. The first method involved three steps: (1) use of a wet high-intensity magnetic separator, where only the equipment’s remaining magnetic field was present; (2) the material from the first step was then submitted to separation again, this time using a magnet for rare earth particles; and (3) this material after two separation processes was finally submitted to ferromagnetic separation. The second method used a concentration table set at various inclinations, oscillation frequencies and wash flow rates. Meanwhile, for the third method, the cyclone tests, only the water pressure was varied. After each test, a chemical analysis was performed to determine the metallic iron present in each sample. The tests revealed that magnetic separation presents the best results. Using this technique, a ferrous concentrate with 93 % metallic iron content and a granite concentrate with only 0.6 % metallic iron were obtained. On the other hand, in the table concentrator tests, the ferrous concentrate only had a metallic concentration of 13.6 %. In separation by the cyclone processing, the product barely contained metallic iron (7.2 % maximum).

Radioactive wastes processing and disposing container

International Nuclear Information System (INIS)

Wada, Jiro; Kato, Hiroaki.

1987-01-01

Purpose: To obtain a processing and disposing container at low level radioactive wastes, excellent in corrosion and water resistance, as well as impact shock resistance for the retrieval storage over a long period of time. Constitution: The container is constituted with sands and pebbles as aggregates and glass fiber-added unsaturated polyester resins as binders. The container may entirely be formed with such material or only the entire inner surface may be formed with the material as liners. A container having excellent resistance to water, chemicals, freezing or melting, whether impact shock, etc. can be obtained, thereby enabling retrieval storage for radioactive wastes at the optimum low level. (Takahashi, M.)

Effect of temperature in domestic refrigerators on fresh-cut Iceberg salad quality and waste.

Science.gov (United States)

Manzocco, L; Alongi, M; Lagazio, C; Sillani, S; Nicoli, M C

2017-12-01

The evolution of different quality parameters (firmness, weight loss, colour changes, microbial counts, consumer rejection) of packed fresh-cut Iceberg salad was assessed at 4, 8 and 12°C to simulate domestic refrigerators running at different conditions. The increase in storage temperature did not affect salad firmness and weight loss but increased colour changes, microbial growth and consumer rejection. A survey among Italian consumers was also carried out and demonstrated that fresh-cut salad was mainly consumed within the first 5days after purchasing. Consumer rejection data were combined with data relevant to the distribution of salad consumption over the days following product purchase, to estimate salad wasting risk. When salad was stored at 4 and 8°C, estimated wasted packages within the expiration date (7days) were sustainable interventions to tackle food waste. Copyright © 2017 Elsevier Ltd. All rights reserved.

Cutting and machining energetic materials with a femtosecond laser

Energy Technology Data Exchange (ETDEWEB)

Roeske, Frank; Benterou, Jerry; Lee, Ronald; Roos, Edward [Energetic Materials Center, Lawrence Livermore National Laboratory, P. O. Box 808, Livermore, CA 94550 (United States)

2003-04-01

A femtosecond (fs) laser has been used as a tool for solving many problems involving access, machining, disassembly, inspection and avoidance of undesirable hazardous waste streams in systems containing energetic materials. Because of the unique properties of the interaction of ultrashort laser pulses with matter, the femtosecond laser can be used to safely cut these energetic materials in a precise manner without creating an unacceptable waste stream. Many types of secondary high explosives (HE) and propellants have been cut with the laser for a variety of applications ranging from disassembly of aging conventional weapons (demilitarization), inspection of energetic components of aging systems to creating unique shapes of HE for purposes of initiation and detonation physics studies. Hundreds of samples of energetic materials have been cut with the fs laser without ignition and, in most cases, without changing the surface morphology of the cut surfaces. The laser has also been useful in cutting nonenergetic components in close proximity to energetic materials. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

Beverage containers in municipal waste

Energy Technology Data Exchange (ETDEWEB)

Enhoerning, B

1979-01-01

The composition of containers (cans, glass) in Sweden's wastes is given. Recycling and reclamation of these containers are discussed. The energy demand of fabricating the containers is analyzed for recycling rates of 0 and 100%. The free forces of the market cannot be depended on to direct the containers back to the manufacturer; only a well-functioning deposit system can do this. 7 figures. (DLC)

Waste management of ENM-containing solid waste in Europe

DEFF Research Database (Denmark)

Heggelund, Laura Roverskov; Boldrin, Alessio; Hansen, Steffen Foss

2015-01-01

the Danish nanoproduct inventory (www.nanodb.dk) to get a general understanding of the fate of ENM during waste management in the European context. This was done by: 1. assigning individual products to an appropriate waste material fraction, 2. identifying the ENM in each fraction, 3. comparing identified...... waste fractions with waste treatment statistics for Europe, and 4. illustrating the general distribution of ENM into incineration, recycling and landfilling. Our results indicate that ╲plastic from used product containers╡ is the most abundant and diverse waste fraction, comprising a variety of both...... nanoproducts and materials. While differences are seen between individual EU countries/regions according to the local waste management system, results show that all waste treatment options are significantly involved in nanowaste handling, suggesting that research activities should cover different areas...

Secondary waste characteristics and ITS filtration system on laser cutting

Energy Technology Data Exchange (ETDEWEB)

Hara, Kunio; Miyao, Hidehiko [Research Association for Facility Decommissioning (RANDEC), Tokai, Ibaraki (Japan); Nakazawa, Masaharu [Tokyo Univ. (Japan); Kataoka, Shinichi; Nagura, Yasumi; Saiki, Hideo [Mitsubishi Heavy Industries Ltd., Tokyo (Japan)

2001-03-01

Technology of dismantling nuclear facilities has been developing in various fields for its evaluation and dismantling system. RANDEC has been studying remote dismantling system for highly activated equipments such as core internals with a laser using optical fiber. Recently a high power YAG laser having the advantage of application for remote dismantling on thick metallic material is the stage for practical use, and narrow kerf can bring the reduction of secondary waste as well. The present paper describes the experimental results and discussion on the laser cutting, including the secondary waste characteristics and its filtration system using the YAG laser. This study has been performed on consignment to RANDEC from the Science and Technology Agency of Japan. (author)

Mass transfer from penetrations in waste containers

International Nuclear Information System (INIS)

Pescatore, C.; Sastre, C.

1987-01-01

Recent studies have indicated that localized corrosion of a relatively small area of a waste container may impair the containment function to such an extent that larger releases may be possible than from the bare waste form. This would take place when a large number of holes coexist on the container while their concentration fields do not interact significantly with each other. After performing a steady state analysis of the release from a hole, it is shown that much fewer independent holes can coexist on a container surface than previously estimated. The calculated radionuclide release from multiple independent holes must be changed accordingly. Previous analyses did not proceed to a correct application of the linear superposition principle. This resulted in unacceptable physical conclusions and undue strain on the performance assessment necessary for a container licensing procedure. The paper also analyzes the steady state release from penetrations of finite length and whose concentration fields interact with one another. The predicted release from these penetrations is lower than the previously calculated release from holes of zero thickness. It is concluded here that the steady-state release from multiple holes on a waste container can not exceed the release from the bare waste form and that multiple perforations need not be a serious liability to container performance. 8 refs., 3 figs., 1 tab

DESIGN ANALYSIS FOR THE DEFENSE HIGH-LEVEL WASTE DISPOSAL CONTAINER

International Nuclear Information System (INIS)

Radulesscu, G.; Tang, J.S.

2000-01-01

The purpose of ''Design Analysis for the Defense High-Level Waste Disposal Container'' analysis is to technically define the defense high-level waste (DHLW) disposal container/waste package using the Waste Package Department's (WPD) design methods, as documented in ''Waste Package Design Methodology Report'' (CRWMS M andO [Civilian Radioactive Waste Management System Management and Operating Contractor] 2000a). The DHLW disposal container is intended for disposal of commercial high-level waste (HLW) and DHLW (including immobilized plutonium waste forms), placed within disposable canisters. The U.S. Department of Energy (DOE)-managed spent nuclear fuel (SNF) in disposable canisters may also be placed in a DHLW disposal container along with HLW forms. The objective of this analysis is to demonstrate that the DHLW disposal container/waste package satisfies the project requirements, as embodied in Defense High Level Waste Disposal Container System Description Document (SDD) (CRWMS M andO 1999a), and additional criteria, as identified in Waste Package Design Sensitivity Report (CRWMS M andQ 2000b, Table 4). The analysis briefly describes the analytical methods appropriate for the design of the DHLW disposal contained waste package, and summarizes the results of the calculations that illustrate the analytical methods. However, the analysis is limited to the calculations selected for the DHLW disposal container in support of the Site Recommendation (SR) (CRWMS M andO 2000b, Section 7). The scope of this analysis is restricted to the design of the codisposal waste package of the Savannah River Site (SRS) DHLW glass canisters and the Training, Research, Isotopes General Atomics (TRIGA) SNF loaded in a short 18-in.-outer diameter (OD) DOE standardized SNF canister. This waste package is representative of the waste packages that consist of the DHLW disposal container, the DHLW/HLW glass canisters, and the DOE-managed SNF in disposable canisters. The intended use of this

DESIGN ANALYSIS FOR THE DEFENSE HIGH-LEVEL WASTE DISPOSAL CONTAINER

Energy Technology Data Exchange (ETDEWEB)

G. Radulesscu; J.S. Tang

2000-06-07

The purpose of ''Design Analysis for the Defense High-Level Waste Disposal Container'' analysis is to technically define the defense high-level waste (DHLW) disposal container/waste package using the Waste Package Department's (WPD) design methods, as documented in ''Waste Package Design Methodology Report'' (CRWMS M&O [Civilian Radioactive Waste Management System Management and Operating Contractor] 2000a). The DHLW disposal container is intended for disposal of commercial high-level waste (HLW) and DHLW (including immobilized plutonium waste forms), placed within disposable canisters. The U.S. Department of Energy (DOE)-managed spent nuclear fuel (SNF) in disposable canisters may also be placed in a DHLW disposal container along with HLW forms. The objective of this analysis is to demonstrate that the DHLW disposal container/waste package satisfies the project requirements, as embodied in Defense High Level Waste Disposal Container System Description Document (SDD) (CRWMS M&O 1999a), and additional criteria, as identified in Waste Package Design Sensitivity Report (CRWMS M&Q 2000b, Table 4). The analysis briefly describes the analytical methods appropriate for the design of the DHLW disposal contained waste package, and summarizes the results of the calculations that illustrate the analytical methods. However, the analysis is limited to the calculations selected for the DHLW disposal container in support of the Site Recommendation (SR) (CRWMS M&O 2000b, Section 7). The scope of this analysis is restricted to the design of the codisposal waste package of the Savannah River Site (SRS) DHLW glass canisters and the Training, Research, Isotopes General Atomics (TRIGA) SNF loaded in a short 18-in.-outer diameter (OD) DOE standardized SNF canister. This waste package is representative of the waste packages that consist of the DHLW disposal container, the DHLW/HLW glass canisters, and the DOE-managed SNF in disposable

Cadmium-containing waste and recycling possibilities

International Nuclear Information System (INIS)

Wiegand, V.; Rauhut, A.

1981-01-01

To begin with, the processes of cadmium production from zinc ores in smelting plants or from intermediates of other metal works are described. A considerable amount of the cadmium is obtained in the recycling process in zinc, lead, and copper works. The way of the cadmium-containing intermediaries, processing, enrichment, and disposal of cadmium waste are described. Uses of cadmium and its compounds are mentioned, and cadmium consumption in the years 1973-1977 in West Germany is presented in a table. Further chapters discuss the production and the way of waste during production and processing of cadmium-containing products, the problem of cadmium in household refuse and waste incineration plants, and the problem of cadmium emissions. (IHOE) [de

MAVL wastes containers functional demonstration and associated tests program

International Nuclear Information System (INIS)

Templier, J.C.

2002-01-01

In the framework of studies on the MAVL wastes, the CEA develops containers for middle time wastes storage. This program aims to realize a ''B wastes containers'' demonstrator. A demonstrator is a container, parts of a container or samples which must validate the tests. This document presents the state of the study in the following three chapters: functions description, base data and design choices; presentation of the functional demonstrators; demonstration tests description. (A.L.B.)

Technology development for cutting a reactor pressure vessel using a mechanical cutting technique

International Nuclear Information System (INIS)

Watanabe, Masaaki; Miyasaka, Yasuhiko; Miyao, Hidehiko; Ooki, Arahiko; Ninomiya, Toshiaki; Koiwai, Masami

2001-01-01

On decommissioning of nuclear facilities, the thermal cutting technique such as an oxygen-acetylene gas cutting and a plasma arc cutting are generally used for cutting massive and thick steel structures in consideration with cutting speed and control performance. These techniques generate dust, smoke, aerosol and a large quantity of secondary waste. Mechanical cutting technique has an advantage of small amount of secondary waste, and the metal chips from the kerf recovered easily compared with these thermal cutting technique. The remote mechanical cutting system for highly activated RPV has been developed with the manner which achieves the safety and cost effectiveness. The development has been performed on consignment to RANDEC from the Science and Technology Agency of Japan. (author)

Equilibrium chemical transformations in NaPO3 + NaCl melts

International Nuclear Information System (INIS)

Kovarskaya, E.N.; Rodionov, Yu.I.

1988-01-01

Because of the problems of the burial of solidified radioactive wastes into different geological rock formations, in particular into massives of rock-salt, the state of molten polyphosphate-chloride mixtures (taking into account the chemical character of the interaction of their components) for a prolonged period of time. The equilibrium products of the reaction in the NaPO 3 -NaCl system were studied in melts in air in the composition range of 30-70 mole % NaCl. It was shown that with increase in the NaCl content in the mixtures, the polyphosphate gradually depolymerizes to sodium tri-, di-, and monophosphates, and the composition of the equilibrium melts is dependent only on the ratio between the components in the initial molten mixtures. The time until the equilibrium is attained is shorter, the higher is the experimental temperature

Apparatus for filling a container with radioactive solid wastes

International Nuclear Information System (INIS)

Adachi, T.; Hiratake, S.

1984-01-01

In apparatus for filling a container suitable for storage with radioactive solid wastes arising from atomic power plants or the like, a plasma arc is irradiated toward a portion of the wastes to melt the portion of the wastes; portions of the wastes are successively moved so as to be subjected to irradiation of the plasma arc to continuously melt the wastes; and the melts obtained by melting the wastes are permitted to flow down toward the bottom of the container

Test plan for buried waste containment system materials

International Nuclear Information System (INIS)

Weidner, J.; Shaw, P.

1997-03-01

The objectives of the FY 1997 barrier material work at the Idaho National Engineering and Environmental Laboratory are to (1) select a waste barrier material and verify that it is compatible with the Buried Waste Containment System Process, and (2) determine if, and how, the Buried Waste Containment System emplacement process affects the material properties and performance (on proof of principle scale). This test plan describes a set of measurements and procedures used to validate a waste barrier material for the Buried Waste Containment System. A latex modified proprietary cement manufactured by CTS Cement Manufacturing Company will be tested. Emplacement properties required for the Buried Waste Containment System process are: slump between 8 and 10 in., set time between 15 and 30 minutes, compressive strength at set of 20 psi minimum, and set temperature less than 100 degrees C. Durability properties include resistance to degradation from carbonate, sulfate, and waste-site soil leachates. A set of baseline barrier material properties will be determined to provide a data base for comparison with the barrier materials when tested in the field. The measurements include permeability, petrographic analysis to determine separation and/or segregation of mix components, and a set of mechanical properties. The measurements will be repeated on specimens from the field test material. The data will be used to determine if the Buried Waste Containment System equipment changes the material. The emplacement properties will be determined using standard laboratory procedures and instruments. Durability of the barrier material will be evaluated by determining the effect of carbonate, sulfate, and waste-site soil leachates on the compressive strength of the barrier material. The baseline properties will be determined using standard ASTM procedures. 9 refs., 1 fig., 2 tabs

Processing of nuclear power plant waste streams containing boric acid

International Nuclear Information System (INIS)

1996-10-01

Boric acid is used in PWR type reactor's primary coolant circuit to control the neutron flux. However, boric acid complicates the control of water chemistry of primary coolant and the liquid radioactive waste produced from NPP. The purpose of this report is to provide member states with up-to-date information and guidelines for the treatment and conditioning of boric acid containing wastes. It contains chapters on: (a) characteristics of waste streams; (b) options for management of boric acid containing waste; (c) treatment/decontamination of boric acid containing waste; (d) concentration and immobilization of boric acid containing waste; (e) recovery and re-use of boric acid; (f) selected industrial processes in various countries; and (g) the influence of economic factors on process selection. 72 refs, 23 figs, 5 tabs

Properties of radioactive wastes and waste containers

International Nuclear Information System (INIS)

Arora, H.S.; Dayal, R.

1984-01-01

Major tasks in this NRC-sponsored program include: (1) an evaluation of the acceptability of low-level solidified wastes with respect to minimizing radionuclide releases after burial; and (2) an assessment of the influence of pertinent environmental stresses on the performance of high-integrity radwaste container (HIC) materials. The waste form performance task involves studies on small-scale laboratory specimens to predict and extrapolate: (1) leachability for extended time periods; (2) leach behavior of full-size forms; (3) performance of waste forms under realistic leaching conditions; and (4) leachability of solidified reactor wastes. The results show that leach data derived from testing of small-scale specimens can be extrapolated to estimate leachability of a full-scale specimen and that radionuclide release data derived from testing of simulants can be employed to predict the release behavior of reactor wastes. Leaching under partially saturated conditions exhibits lower releases of radionuclides than those observed under the conventional IAEA-type or ANS 16.1 leach tests. The HIC assessment task includes the characterization of mechanical properties of Marlex CL-100, a candidate radwaste high density polyethylene material. Tensile strength and creep rupture tests have been carried out to determine the influence of specific waste constituents as well as gamma irradiation on material performance. Emphasis in ongoing tests is being placed on studying creep rupture while the specimens are in contact with a variety of chemicals including radiolytic by-products of irradiated resin wastes. 12 references 6 figures, 2 tables

Processing method and device for radioactive waste containing surfactant

International Nuclear Information System (INIS)

Yukita, Atsushi; Yoshikawa, Ryozo; Izumida, Tatsuo; Nishi, Takashi; Hattori, Yasuo.

1997-01-01

Washing liquid wastes generated in washing facilities in a nuclear power plant are collected in a liquid waste collecting tank. A suspension containing a powdery active carbon is supplied to the liquid waste collecting tank. Organic ingredients such as of a surfactant, oil ingredients and radioactive materials in the form of ions contained in the washing liquid wastes are adsorbed to the powdery active carbon. The washing liquid wastes containing the powdery active carbon and granular radioactive materials are led into an active carbon separating and drying device. The powdery active carbon and granular radioactive materials contained in the washing liquid wastes are filtered and separated by a filtering plate, and accumulated as filtered materials on the surface of the filtering plate. The purified washing liquid wastes are discharged to the outside. The filtered materials are dried by hot steams (or hot water) and dried air. The filtered materials are peeled from the filtering plate. The filtered materials, in other word, dried powdery active carbon and granular radioactive materials are transported to and burnt in an incinerator. (I.N.)

Plasma methods for metals recovery from metal-containing waste.

Science.gov (United States)

Changming, Du; Chao, Shang; Gong, Xiangjie; Ting, Wang; Xiange, Wei

2018-04-27

Metal-containing waste, a kind of new wastes, has a great potential for recycling and is also difficult to deal with. Many countries pay more and more attention to develop the metal recovery process and equipment of this kind of waste as raw material, so as to solve the environmental pollution and comprehensively utilize the discarded metal resources. Plasma processing is an efficient and environmentally friendly way for metal-containing waste. This review mainly discuss various metal-containing waste types, such as printed circuit boards (PCBs), red mud, galvanic sludge, Zircon, aluminium dross and incinerated ash, and the corresponding plasma methods, which include DC extended transferred arc plasma reactor, DC non-transferred arc plasma torch, RF thermal plasma reactor and argon and argon-hydrogen plasma jets. In addition, the plasma arc melting technology has a better purification effect on the extraction of useful metals from metal-containing wastes, a great capacity of volume reduction of waste materials, and a low leaching toxicity of solid slag, which can also be used to deal with all kinds of metal waste materials, having a wide range of applications. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effect on localized waste-container failure on radionuclide transport from an underground nuclear waste vault

International Nuclear Information System (INIS)

Cheung, S.C.H.; Chan, T.

1983-07-01

In the geological disposal of nuclear fuel waste, one option is to emplace the waste container in a borehole drilled into the floor of the underground vault. In the borehole, the waste container is surrounded by a compacted soil material known as the buffer. A finite-element simulation has been performed to study the effect of localized partial failure of the waste container on the steady-state radionuclide transport by diffusion from the container through the buffer to the surrounding rock and/or backfill. In this study, the radionuclide concentration at the buffer-backfill interface is assumed to be zero. Two cases are considered at the interface between the buffer and the rock. In case 1, a no-flux boundary condition is used to simulate intact rock. In case 2, a constant radionuclide concentration condition is used to simulate fractured rock with groundwater flow. The results show that the effect of localized partial failure of the waste container on the total flux is dependent on the boundary condition at the buffer-rock interface. For the intact rock condition, the total flux is mainly dependent on the location of the failure. The total flux increases as the location changes from the bottom to the top of the emplaced waste container. For a given localized failure of the waste container, the total flux remains unaffected by the area of failed surface below the top of the failure. For fractured rock, the total flux is directly proportional to the failed surface area of the waste container regardless of the failure location

Radioactive waste sealing container

International Nuclear Information System (INIS)

Tozawa, S.; Kitamura, T.; Sugimoto, S.

1984-01-01

A low- to medium-level radioactive waste sealing container is constructed by depositing a foundation coating consisting essentially of zinc, cadmium or a zinc-aluminum alloy over a steel base, then coating an organic synthetic resin paint containing a metal phosphate over the foundation coating, and thereafter coating an acryl resin, epoxy resin, and/or polyurethane paint. The sealing container can consist of a main container body, a lid placed over the main body, and fixing members for clamping and fixing the lid to the main body. Each fixing member may consist of a material obtained by depositing a coating consisting essentially of cadmium or a zinc-aluminum alloy over a steel base

A container for storage and disposal of low-level waste

International Nuclear Information System (INIS)

Fish, R.L.; Butler, B.D.

1989-01-01

A unique concept for corrosion-resistant containers for storing and disposing of low-level radioactive, mixed and toxic wastes has been developed. The strength and low cost of carbon steel has been combined with the corrosion and abrasion resistance of a proprietary combination of polymers to provide an inexpensive alternative to currently available waste containers. The initial development effort has focused on a 55-gallon container, the B and W ECOSAFE-55 tm . However, Babcock and Wilcox (B and W) can develop a family of ECOSAFE waste containers using this technology to accommodate user-preferred configurations and volumes. The containers will be capable of accepting a wide range of low-level radioactive (LLRW) and industrial waste forms. Basic engineering design analyses and functional tests were performed to show compliance of the container with transportation functional requirements. These tests and analyses, along with chemical resistance tests, qualify the container for use in storing a wide range of radioactive and chemical wastes. For the container to be licensed for use as a high-integrity container in shallow land, low-level radioactive waste burial facilities, the Nuclear Regulatory Commission requires certain tests and analyses to demonstrate that container gross physical properties and identity can be maintained for 300 years. This paper describes the container concept in generic terms and provides information on the initial, ECOSAFE-55 container design, testing and engineering analysis efforts

Materials for high-level waste containment

International Nuclear Information System (INIS)

Marsh, G.P.

1982-01-01

The function of the high-level radioactive waste container in storage and of a container/overpack combination in disposal is considered. The consequent properties required from potential fabrication materials are discussed. The strategy adopted in selecting containment materials and the experimental programme underway to evaluate them are described. (U.K.)

Monitoring of wastes containing plutonium. Necessity and method

International Nuclear Information System (INIS)

Sousselier, Y.; Pottier, P.

1979-01-01

Importance of problems set by wastes containing plutonium is rapidly growing. Plutonium is not a waste, recycling limits heavily the quantity of plutonium to be stored with wastes. Optimized waste management must take definitive storage and economical limits of plutonium recovery into account. Waste monitoring is a must for safety, economy and waste management. Methods used require reliability, simplicity, sensibility and accuracy particularly for threshold detection [fr

Conveyor Cultivation of the Halophytic Plant Salicornia europaea for the Recycling of NaCl from Human Liquid Waste in a Biological Life Support System.

Science.gov (United States)

Balnokin, Yurii; Myasoedov, Nikolay; Popova, Larissa; Tikhomirov, Alexander A.; Ushakova, Sofya; Tikhomirova, Natalia; Lasseur, Christophe; Gros, Jean-Bernard

One problem in designing bioregenerative life support systems (BLSS) is developing technolo-gies to include human liquid and solid waste in intrasystem recycling. A specific task is recycling of NaCl excreted in urine by humans. We showed recently that this could be achieved through inclusion of the salt accumulating halophyte Salicornia europaea in the autotrophic compart-ment of the BLSS (Balnokin et al., ASR, 2010, in press). A model of NaCl circulation in BLSS with inclusion of S. europaea was based on the NaCl turnover in the human -urine -nutrient solution -S. europaea -human cycle. Mineralized urine was used as a basis for preparation of a nutrient solution for the halophyte cultivation. The shoots of the halophyte cultivated in the mineralized urine and containing NaCl could to be used by the BLSS inhabitants in their diets. In this report we describe cultivation of S. europaea which allows turnover of NaCl and produces daily shoot biomass containing Na+ and Cl- in quantities approximately equal to those excreted in daily human urine. The plants were grown in water culture in a climatic chamber under controlled conditions. A solution simulating mineralized urine (SSMU) was used as a basis for preparation of a nutri-ent solution for S. europaea cultivation. For continuous biomass production, seedlings of S. europaea, germinated preliminary in moist sand, were being transferred to the nutrient solu-tion at regular intervals (every two days). Duration of the conveyor operation was 112 days. During the first 56 days, the seedlings were being planted in SSMU diluted by a factor of 1.5 (2/3 SSMU). The same solution was introduced into the growth vessels as volumes of growth medium decreased due to plant transpiration. Starting from the 56th day as conveyor operation was initiated, the plants were being harvested every two days; the solutions from the discharged vessels were mixed with the fresh SSMU and the mixture was introduced into all other growth vessels of

Reliability evaluation methodologies for ensuring container integrity of stored transuranic (TRU) waste

International Nuclear Information System (INIS)

Smith, K.L.

1995-06-01

This report provides methodologies for providing defensible estimates of expected transuranic waste storage container lifetimes at the Radioactive Waste Management Complex. These methodologies can be used to estimate transuranic waste container reliability (for integrity and degradation) and as an analytical tool to optimize waste container integrity. Container packaging and storage configurations, which directly affect waste container integrity, are also addressed. The methodologies presented provide a means for demonstrating Resource Conservation and Recovery Act waste storage requirements

Glass containing radioactive nuclear waste

International Nuclear Information System (INIS)

Boatner, L.A.; Sales, B.C.

1985-01-01

Lead-iron phosphate glasses containing a high level of Fe 2 O 3 for use as a storage medium for high-level-radioactive nuclear waste. By combining lead-iron phosphate glass with various types of simulated high-level nuclear waste, a highly corrosion resistant, homogeneous, easily processed glass can be formed. For corroding solutions at 90 C, with solution pH values in the range between 5 and 9, the corrosion rate of the lead-iron phosphate nuclear waste glass is at least 10 2 to 10 3 times lower than the corrosion rate of a comparable borosilicate nuclear waste glass. The presence of Fe 2 O 3 in forming the lead-iron phosphate glass is critical. Lead-iron phosphate nuclear waste glass can be prepared at temperatures as low as 800 C, since they exhibit very low melt viscosities in the 800 to 1050 C temperature range. These waste-loaded glasses do not readily devitrify at temperatures as high as 550 C and are not adversely affected by large doses of gamma radiation in H 2 O at 135 C. The lead-iron phosphate waste glasses can be prepared with minimal modification of the technology developed for processing borosilicate glass nuclear waste forms. (author)

Container for waste, identification code reading device thereof, method and system for controlling waste by using them

International Nuclear Information System (INIS)

Kikuchi, Takashi; Yoshida, Tomiji; Omote, Tatsuyuki.

1991-01-01

In the conventional method of controlling waste containers by labels attached thereto, the data relevant to wastes contained in the waste containers are limited. Further, if the label should be peeled off, there is a possibility that the wastes therein can no more be identified. Then, in the present invention, an identification plate is previously attached, to which mechanically readable codes or visually readable letters or numerical figures are written. Then, the identification codes can be read in a remote control manner at high speed and high reliability and the waste containers can be managed only by the identification codes of the containers. Further, the identification codes on the container are made so as to be free from aging degradation, thereby enabling to manage waste containers for long time storage. With such a constitution, since data can be inputted from an input terminal and a great amount of data such as concerning the source of wastes can be managed collectively on a software, the data can be managed easily. (T.M.)

Recovering low-turbidity cutting liquid from silicon slurry waste.

Science.gov (United States)

Tsai, Tzu-Hsuan; Shih, Yu-Pei

2014-04-30

In order to recover a low-turbidity polyalkylene glycol (PAG) liquid from silicon slurry waste by sedimentation, temperatures were adjusted, and acetone, ethanol or water was used as a diluent. The experimental results show that the particles in the waste would aggregate and settle readily by using water as a diluent. This is because particle surfaces had lower surface potential value and weaker steric stabilization in PAG-water than in PAG-ethanol or PAG-acetone solutions. Therefore, water is the suggested diluent for recovering a low-turbidity PAG (sedimentation. After 50 wt.% water-assisted sedimentation for 21 days, the solid content of the upper liquid reduced to 0.122 g/L, and the turbidity decreased to 44 NTU. The obtained upper liquid was then vacuum-distillated to remove water. The final recovered PAG with 0.37 NTU had similar viscosity and density to the unused PAG and could be reused in the cutting process. Copyright © 2014 Elsevier B.V. All rights reserved.

Method of processing nitrate-containing radioactive liquid wastes

International Nuclear Information System (INIS)

Ogawa, Norito; Nagase, Kiyoharu; Otsuka, Katsuyuki; Ouchi, Jin.

1983-01-01

Purpose: To efficiently concentrate nitrate-containing low level radioactive liquid wastes by electrolytically dialyzing radioactive liquid wastes to decompose the nitrate salt by using an electrolytic cell comprising three chambers having ion exchange membranes and anodes made of special materials. Method: Nitrate-containing low level radioactive liquid wastes are supplied to and electrolytically dialyzed in a central chamber of an electrolytic cell comprising three chambers having cationic exchange membranes and anionic exchange membranes made of flouro-polymer as partition membranes, whereby the nitrate is decomposed to form nitric acid in the anode chamber and alkali hydroxide compound or ammonium hydroxide in the cathode chamber, as well as concentrate the radioactive substance in the central chamber. Coated metals of at least one type of platinum metal is used as the anode for the electrolytic cell. This enables efficient industrial concentration of nitrate-containing low level radioactive liquid wastes. (Yoshihara, H.)

Development of high integrity containers for rad-waste treatment

Energy Technology Data Exchange (ETDEWEB)

Song, Yung Chul; Cho, Myung Sug; Jung, Yun Sub [Korea Electric Power Corp. (KEPCO), Taejon (Korea, Republic of). Research Center

1995-12-31

Nuclear power plants are generating rad waste such as solid wastes, concentrated liquid wastes, spent resins and spent filters, and various types of imported containers which have different specifications and material properties are employed to handle the rad wastes according to facility characteristics of the plants or the type of wastes. These containers are stored at the intermediate storage facilities at the plant site due to the construction delay of permanent disposal site, and the additional construction of storage and disposal sites become more difficult with increase of the numbers and the operation time of the plants. In order to solve these difficulties, rad wastes volume reduction facilities such as High Pressure Compression Facility or Drying Facility are being installed and use of High Integrity Containers(HIC) are increasing. Therefore, we decide quality and technology standards required for the HIC, and then develop the HIC which satisfies the standards with new composite material called Steel Fiber Polymer Impregnated Concrete(SFPIC) (author). 84 refs., 118 figs.

Development of high integrity containers for rad-waste treatment

Energy Technology Data Exchange (ETDEWEB)

Song, Yung Chul; Cho, Myung Sug; Jung, Yun Sub [Korea Electric Power Corp. (KEPCO), Taejon (Korea, Republic of). Research Center

1996-12-31

Nuclear power plants are generating rad waste such as solid wastes, concentrated liquid wastes, spent resins and spent filters, and various types of imported containers which have different specifications and material properties are employed to handle the rad wastes according to facility characteristics of the plants or the type of wastes. These containers are stored at the intermediate storage facilities at the plant site due to the construction delay of permanent disposal site, and the additional construction of storage and disposal sites become more difficult with increase of the numbers and the operation time of the plants. In order to solve these difficulties, rad wastes volume reduction facilities such as High Pressure Compression Facility or Drying Facility are being installed and use of High Integrity Containers(HIC) are increasing. Therefore, we decide quality and technology standards required for the HIC, and then develop the HIC which satisfies the standards with new composite material called Steel Fiber Polymer Impregnated Concrete(SFPIC) (author). 84 refs., 118 figs.

Potential impact of salinity on methane production from food waste anaerobic digestion.

Science.gov (United States)

Zhao, Jianwei; Liu, Yiwen; Wang, Dongbo; Chen, Fei; Li, Xiaoming; Zeng, Guangming; Yang, Qi

2017-09-01

Previous studies have demonstrated that the presence of sodium chloride (NaCl) inhibited the production of methane from food waste anaerobic digestion. However, the details of how NaCl affects methane production from food waste remain unknown by now and the efficient approach to mitigate the impact of NaCl on methane production was seldom reported. In this paper, the details of how NaCl affects methane production was first investigated via a series of batch experiments. Experimental results showed the effect of NaCl on methane production was dosage dependent. Low level of NaCl improved the hydrolysis and acidification but inhibited the process of methanogenesis whereas high level of NaCl inhibit both steps of acidification and methanogenesis. Then an efficient approach, i.e. co-digestion of food waste and waste activated sludge, to mitigate the impact of NaCl on methane production was reported. Finally, the mechanisms of how co-digestion mitigates the effect on methane production caused by NaCl in co-digestion system were revealed. These findings obtained in this work might be of great importance for the operation of methane recovery from food waste in the presence of NaCl. Copyright © 2017 Elsevier Ltd. All rights reserved.

PIC-container for containment and disposal of low and intermediate level radioactive wastes

International Nuclear Information System (INIS)

Araki, Kunio; Shinji, Yoshimasa; Maki, Yasuro; Ishizaki, Kanjiro; Minegishi, Keiichi; Sudoh, Giichi.

1981-03-01

Steel fiber reinforced polymer-impregnated concrete (SFPIC) has been investigated for low and intermediate level radioactive waste containers. The present study has been carried out by the following stages. A) Preliminary evaluation: 60 L size container for cold and hot tests. B) Evaluation of size effect: 200 L size container for cold tests. The 60 L and 200 L containers were designed as pressure-container (without equalizer) for 500 kg/cm 2 and 700 kg/cm 2 . Polymerization of impregnated methylmethacrylate monomer for stage-A and B were performed by 60 Co-γ ray radiation and thermal catalytic polymerization, respectively. Under the loading of 500 kg/cm 2 and 700 kg/cm 2 -outside hydraulic pressure, these containers were kept in their good condition. The observed maximum strains were about 1380 x 10 -6 and 3950 x 10 -6 at the outside central position of container body for circumferential direction of the 60 L and 200 L container, respectively. An accelerated leaching test was performed by charging the concentrate of the liquid radioactive waste from JMTR in JAERI into the container. Although they were immersed in deionized water for 400 days, nuclides were not leached from the container. From results of various tests, it was evaluated that the SFPIC-container was suitable for containment and disposal of low and intermediate level radioactive wastes. There was not any great difference between the two size containers for the physical and chemical properties except in their preparation process. (author)

Disposal containers for radioactive waste materials and separation systems for radioactive waste materials

International Nuclear Information System (INIS)

Rubin, L.S.

1986-01-01

A separation system for dewatering radioactive waste materials includes a disposal container, drive structure for receiving the container, and means for releasably attaching the container to the drive structure. The separation structure disposed in the container adjacent the inner surface of the side wall structure retains solids while allowing passage of liquids. The inlet port structure in the container top wall is normally closed by first valve structure that is centrifugally actuated to open the inlet port and the discharge port structure at the container periphery receives liquid that passes through the separation structure and is normally closed by a second valve structure that is centrifugally actuated to open the discharge ports. The container also includes a coupling structure for releasable engagement with the centrifugal drive structure. The centrifugal force produced when the container is driven in rotation by the drive structure opens the valve structures, and radioactive waste material introduced into the container through the open inlet port is dewatered, and the waste is compacted. The ports are automatically closed by the valves when the container drum is not subjected to centrifugal force such that containment effectiveness is enhanced and exposure of personnel to radioactive materials is minimized. (author)

Treatment of nanomaterial-containing waste in thermal waste treatment facilities; Behandlung nanomaterialhaltiger Abfaelle in thermischen Abfallbehandlungsanlagen

Energy Technology Data Exchange (ETDEWEB)

Vogel, Julia; Weiss, Volker [Umweltbundesamt, Dessau-Rosslau (Germany); Oischinger, Juergen; Meiller, Martin; Daschner, Robert [Fraunhofer Umsicht, Sulzbach-Rosenberg (Germany)

2016-09-15

There is already a multitude of products on the market, which contain synthetic nanomaterials (NM), and for the coming years an increase of such products can be expected. Consequently, it is predictable that more nanomaterial-containing waste will occur in the residual waste that is predominately disposed in thermal waste treatment plants. However, the knowledge about the behaviour and effects of nanomaterials from nanomaterial-containing waste in this disposal route is currently still low. A research project of the German Environment Agency on the ''Investigation of potential environmental impacts when disposing nanomaterial-containing waste in waste treatment plants'' will therefore dedicate itself to a detailed examination of emission pathways in the thermal waste treatment facilities. The tests carried out i.a. on an industrial waste incineration plant and a sludge incineration plant with controlled addition of titanium dioxide at the nanoscale, showed that no increase in the emissions of NM in the exhaust gas was detected. The majority of the NM was found in the combustion residues, particularly the slag.

Container for processing and disposing radioactive wastes and industrial wastes

International Nuclear Information System (INIS)

Araki, Kunio; Kasahara, Yuko; Kasai, Noboru; Sudo, Giichi; Ishizaki, Kanjiro.

1978-01-01

Purpose: To improve the performance of containers for radioactive wastes for ocean disposal and on-land disposal such as impact strength, chemical resistance, fire resistance, corrosion resistance, water impermeability and the like. Constitution: Steel fiber-reinforced concrete previously molded in a shape of a container is impregnated with polymerizable impregnating agent selected from the group consisting of a polymerizable monomer, liquid mixture of a polymerizable monomer and an oligomer, a polymer solution, a copolymer solution and the liquid mixture thereof. Then, the polymerizable impregnating agent is polymerized to solidify in the concrete by way of heat-polymerization or radiation-induced polymerization to form a waste container. The container thus obtained can be improved with the impact resistance and wear resistance and further improved with salt water resistance, acid resistance, corrosion resistance and solidity by the impregnation of the polymer, as well as can effectively be prevented from leaching out of radioactive substances. (Furukawa, Y.)

LCA comparison of container systems in municipal solid waste management

International Nuclear Information System (INIS)

Rives, Jesus; Rieradevall, Joan; Gabarrell, Xavier

2010-01-01

The planning and design of integrated municipal solid waste management (MSWM) systems requires accurate environmental impact evaluation of the systems and their components. This research assessed, quantified and compared the environmental impact of the first stage of the most used MSW container systems. The comparison was based on factors such as the volume of the containers, from small bins of 60-80 l to containers of 2400 l, and on the manufactured materials, steel and high-density polyethylene (HDPE). Also, some parameters such as frequency of collections, waste generation, filling percentage and waste container contents, were established to obtain comparable systems. The methodological framework of the analysis was the life cycle assessment (LCA), and the impact assessment method was based on CML 2 baseline 2000. Results indicated that, for the same volume, the collection systems that use HDPE waste containers had more of an impact than those using steel waste containers, in terms of abiotic depletion, global warming, ozone layer depletion, acidification, eutrophication, photochemical oxidation, human toxicity and terrestrial ecotoxicity. Besides, the collection systems using small HDPE bins (60 l or 80 l) had most impact while systems using big steel containers (2400 l) had less impact. Subsequent sensitivity analysis about the parameters established demonstrated that they could change the ultimate environmental impact of each waste container collection system, but that the comparative relationship between systems was similar.

29 CFR 1915.54 - Welding, cutting and heating of hollow metal containers and structures not covered by § 1915.12.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Welding, cutting and heating of hollow metal containers and... STANDARDS FOR SHIPYARD EMPLOYMENT Welding, Cutting and Heating § 1915.54 Welding, cutting and heating of... which have contained flammable substances shall, before welding, cutting, or heating is undertaken on...

Cast-iron containers out of low radioactive steel

International Nuclear Information System (INIS)

Deipenau, H.; Seidler, M.

1990-01-01

Low-level radioactive solid waste from the decommissioning of nuclear installations, if transported and disposed of in large containers, may cause less cutting work and therefore less radiation exposure of the work-force. The use of steel waste from decommissioning for manufacturing large transport and/or disposal containers is a promising route for recycling that waste and for saving storage volume and new resources. It has been demonstrated that it is possible to cast transport and disposal containers for radioactive wastes by using carbon steel waste originating from nuclear installations. A prototype has fulfilled all conditions to reach the qualification as a type A package according to the IAEA Regulations for Safe Transport of Radioactive Material as well as the preliminary conditions of the final repository Konrad

Corrosion electrochemical behaviors of silane coating coated magnesium alloy in NaCl solution containing cerium nitrate

Energy Technology Data Exchange (ETDEWEB)

Luo, F.; Li, Q.; Zhong, X.K.; Gao, H.; Dai, Y.; Chen, F.N. [School of Chemistry and Chemical Engineering, Southwest University Chongqing (China)

2012-02-15

Sol-gel coatings cannot provide adequate corrosion protection for metal/alloys in the corrosive environments due to their high crack-forming potential. This paper demonstrates the possibility to employ cerium nitrate as inhibitor to decrease the corrosion development of sol-gel-based silane coating on the magnesium alloy in NaCl solution. Cerium nitrate was added into the NaCl solution where the silane coating coated magnesium alloy was immersed. Scanning electron microscopy (SEM) was used to examine surface morphology of the silane coating coated magnesium alloy immersed in NaCl solutions doped and undoped with cerium nitrate. The corrosion electrochemical behaviors were investigated using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) tests. The results showed that the introduction of cerium nitrate into NaCl solution could effectively inhibit the corrosion of the silane coating coated magnesium alloy. Moreover, the influence of concentration of cerium nitrate on the corrosion inhibition and the possible inhibiting mechanism were also discussed in detail. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Assessment of gas flammability in transuranic waste container

International Nuclear Information System (INIS)

Connolly, M.J.; Loehr, C.A.; Djordjevic, S.M.; Spangler, L.R.

1995-01-01

The Safety Analysis Report for the TRUPACT-II Shipping Package [Transuranic Package Transporter-II (TRUPACT-II) SARP] set limits for gas generation rates, wattage limits, and flammable volatile organic compound (VOC) concentrations in transuranic (TRU) waste containers that would be shipped to the Waste Isolation Pilot Plant (WIPP). Based on existing headspace gas data for drums stored at the Idaho National Engineering Laboratory (INEL) and the Rocky Flats Environmental Technology Site (RFETS), over 30 percent of the contact-handled TRU waste drums contain flammable VOC concentrations greater than the limit. Additional requirements may be imposed for emplacement of waste in the WIPP facility. The conditional no-migration determination (NMD) for the test phase of the facility required that flame tests be performed if significant levels of flammable VOCs were present in TRU waste containers. This paper describes an approach for investigating the potential flammability of TRU waste drums, which would increase the allowable concentrations of flammable VOCS. A flammability assessment methodology is presented that will allow more drums to be shipped to WIPP without treatment or repackaging and reduce the need for flame testing on drums. The approach includes experimental work to determine mixture lower explosive limits (MLEL) for the types of gas mixtures observed in TRU waste, a model for predicting the MLEL for mixtures of VOCS, hydrogen, and methane, and revised screening limits for total flammable VOCs concentrations and concentrations of hydrogen and methane using existing drum headspace gas data and the model predictions

Containers for packaging of solid and intermediate level radioactive wastes

International Nuclear Information System (INIS)

1993-01-01

Low and intermediate level radioactive wastes are generated at all stages in the nuclear fuel cycle and also from the medical, industrial and research applications of radiation. These wastes can potentially present risks to health and the environment if they are not managed adequately. Their effective management will require the wastes to be safely stored, transported and ultimately disposed of. The waste container, which may be defined as any vessel, drum or box, made from metals, concrete, polymers or composite materials, in which the waste form is placed for interim storage, for transport and/or for final disposal, is an integral part of the whole package for the management of low and intermediate level wastes. It has key roles to play in several stages of the waste management process, starting from the storage of raw wastes and ending with the disposal of conditioned wastes. This report provides an overview of the various roles that a container may play and the factors that are important in each of these roles. This report has two main objectives. The first is to review the main requirements for the design of waste containers. The second is to provide advice on the design, fabrication and handling of different types of containers used in the management of low and intermediate level radioactive solid wastes. Recommendations for design and testing are given, based on the extensive experience available worldwide in waste management. This report is not intended to have any regulatory status or objectives. 56 refs, 16 figs, 10 tabs

A German research project about applicable graphite cutting techniques

International Nuclear Information System (INIS)

Holland, D.; Quade, U.; Bach, F.W.; Wilk, P.

2001-01-01

In Germany, too, quite large quantities of irradiated nuclear graphite, used in research and prototype reactors, are waiting for an environmental way of disposal. While incineration of nuclear graphite does not seem to be a publicly acceptable way, cutting and packaging into ductile cast iron containers could be a suitable way of disposal in Germany. Nevertheless, the cutting of graphite is also a very difficult technique by which a large amount of secondary waste or dust might occur. An applicable graphite cutting technique is needed. Therefore, a group of 13 German partners, consisting of one university, six research reactor operators, one technical inspection authority, three engineering companies, one industrial cutting specialist and one commercial dismantling company, decided in 1999 to start a research project to develop an applicable technique for cutting irradiated nuclear graphite. Aim of the project is to find the most suitable cutting techniques for the existing shapes of graphite blocks with a minimum of waste production rate. At the same time it will be learned how to sample the dust and collect it in a filter system. The following techniques will be tested and evaluated: thermal cutting, water jet cutting, mechanical cutting with a saw, plasma arc cutting, drilling. The subsequent evaluation will concentrate on dust production, possible irradiation of staff, time and practicability under different constraints. This research project is funded by the German Minister of Education and Research under the number 02 S 7849 for a period of two years. A brief overview about the work to be carried out in the project will be given. (author)

Waste-to-energy: Dehalogenation of plastic-containing wastes.

Science.gov (United States)

Shen, Yafei; Zhao, Rong; Wang, Junfeng; Chen, Xingming; Ge, Xinlei; Chen, Mindong

2016-03-01

The dehalogenation measurements could be carried out with the decomposition of plastic wastes simultaneously or successively. This paper reviewed the progresses in dehalogenation followed by thermochemical conversion of plastic-containing wastes for clean energy production. The pre-treatment method of MCT or HTT can eliminate the halogen in plastic wastes. The additives such as alkali-based metal oxides (e.g., CaO, NaOH), iron powders and minerals (e.g., quartz) can work as reaction mediums and accelerators with the objective of enhancing the mechanochemical reaction. The dehalogenation of waste plastics could be achieved by co-grinding with sustainable additives such as bio-wastes (e.g., rice husk), recyclable minerals (e.g., red mud) via MCT for solid fuels production. Interestingly, the solid fuel properties (e.g., particle size) could be significantly improved by HTT in addition with lignocellulosic biomass. Furthermore, the halogenated compounds in downstream thermal process could be eliminated by using catalysts and adsorbents. Most dehalogenation of plastic wastes primarily focuses on the transformation of organic halogen into inorganic halogen in terms of halogen hydrides or salts. The integrated process of MCT or HTT with the catalytic thermal decomposition is a promising way for clean energy production. The low-cost additives (e.g., red mud) used in the pre-treatment by MCT or HTT lead to a considerable synergistic effects including catalytic effect contributing to the follow-up thermal decomposition. Copyright © 2015 Elsevier Ltd. All rights reserved.

Improvement of a separation method for the reduction of secondary waste from the water-jet abrasive suspension cutting technique

International Nuclear Information System (INIS)

Brandauer, M.; Gentes, S.; Heneka, A.; Krauss, C.O.; Geckeis, H.; Plaschke, M.; Schild, D.; Tobie, W.

2017-01-01

Full text of publication follows. Disassembling the reactor pressure vessel and its built-in components is a huge challenge in the deconstruction of a nuclear power plant. After being exposed to neutron irradiation for years, the activated components need to be disassembled and packed by remote controlled techniques. Underwater disassembling systems have the advantage of the shielding effect of water against radiation. To avoid the generation of aerosols, cold cutting processes are preferred. A cutting method that meets these requirements is the water-jet abrasive suspension cutting technique (WASS). This method provides high flexibility and is immune towards mechanical stress in the components. During the cutting process, a mixture of abrasive particles and radioactive steel particles from the cut components is generated. Depending on the operational conditions, the amount of this secondary waste increases substantially. Therefore, despite of its intrinsic technical benefits, WASS has a serious disadvantage towards other cutting techniques due to the huge disposal costs of secondary waste. During our previous joint research project between KIT and AREVA GmbH called NENAWAS ('New Disposal Methods for the Secondary Waste Treatment of the Water-jet Abrasive Suspension Cutting Technique', funded by the German ministry for education and research, BMBF), a prototype separation device for WASS secondary waste was developed and tested. Using a magnetic filter, steel particles could be successfully separated from the rest of the secondary waste. The separation process is examined using elemental analysis (ICP-OES) for quantification of the separation grade. Additionally, morphologies of particles and particle aggregates before and after the separation process were examined by scanning electron microscopy (SEM). In the abrasive particle fraction after separation of the steel particles a remaining contamination by tiny steel particles could be detected by elemental and

Containment of solidified liquid hazardous waste in domal salt

International Nuclear Information System (INIS)

Domenico, P.A.; Lerman, A.

1992-01-01

In recent years, the solidification of hazardous liquid waste has become a viable option in waste management. The solidification process results in an increased volume but more stable waste form that must be disposed of or stored in a dry environment. An environment of choice in south central Texas is domal salt. The salt dome currently under investigation has a water content of 0.002 percent by weight and a permeability less than one nanodarcy. A question that must be addressed is whether a salt dome has a particular set of attributes that will prevent the release of contaminants to the environment. From a regulatory perspective, a ''no migration'' petition must be approved by the U.S.E.P.A. for the containment facility. By ''no migration'' it is implied that the waste must be contained for 10,000 years. A demonstration that this condition will be met will require model calculations and such models must be based on the physical and chemical characteristics of the waste form and the geologic environment. In particular, the models must address the rate of brine infiltration into the caverns, providing information on how fast an immobile solid waste form could convert to a more mobile liquid state. Additionally, the potential for migration by both diffusion and advection is of concern. Lastly, given a partially saturated cavern, the question of how far gaseous waste will be transported over the 10,000 year containment period must also be addressed. Results indicate that the containment capabilities of domal salt are exceptional. A nominal volume of brine will seep into the cavern and most voids between the injected solidified waste pellets will remain unsaturated. Very small quantities of hazardous constituents will be leached from the waste pellets

Vitrification of organics-containing wastes

International Nuclear Information System (INIS)

Bickford, D.F.

1997-01-01

A process is described for stabilizing organics-containing waste materials and recovering metals therefrom, and a waste glass product made according to the process is also disclosed. Vitrification of wastes such as organic ion exchange resins, electronic components and the like can be accomplished by mixing at least one transition metal oxide with the wastes, and, if needed, glass formers to compensate for a shortage of silicates or other glass formers in the wastes. The transition metal oxide increases the rate of oxidation of organic materials in the wastes to improve the composition of the glass-forming mixture: at low temperatures, the oxide catalyzes oxidation of a portion of the organics in the waste; at higher temperatures, the oxide dissolves and the resulting oxygen ions oxidize more of the organics; and at vitrification temperatures, the metal ions conduct oxygen into the melt to oxidize the remaining organics. In addition, the transition metal oxide buffers the redox potential of the glass melt so that metals such as Au, Pt, Ag, and Cu separate from the melt in the metallic state and can be recovered. After the metals are recovered, the remainder of the melt is allowed to cool and may subsequently be disposed of. The product has good leaching resistance and can be disposed of in an ordinary landfill, or, alternatively, used as a filler in materials such as concrete, asphalt, brick and tile. 1 fig

Los Alamos Transuranic Waste Size Reduction Facility

International Nuclear Information System (INIS)

Harper, J.; Warren, J.

1987-06-01

The Los Alamos Transuranic (TRU) Waste Size Reduction Facility (SRF) is a production oriented prototype. The facility is operated to remotely cut and repackage TRU contaminated metallic wastes (e.g., glove boxes, ducting and pipes) for eventual disposal at the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico. The resulting flat sections are packaged into a tested Department of Transportation Type 7A metal container. To date, the facility has successfully processed stainless steel glove boxes (with and without lead shielding construction) and retention tanks. We have found that used glove boxes generate more cutting fumes than do unused glove boxes or metal plates - possibly due to deeply embedded chemical residues from years of service. Water used as a secondary fluid with the plasma arc cutting system significantly reduces visible fume generation during the cutting of used glove boxes and lead-lined glove boxes. 2 figs., 1 tab

Process development for treatment of fluoride containing wastes

Energy Technology Data Exchange (ETDEWEB)

Singh, Mahesh; Kanvinde, V Y [Chemical Engineering Division, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

Many chemical and metallurgical industries generate liquid wastes containing high values of fluorides in association of nitrates and other metals. Due to harmful effects of fluorides these type of wastes can not be disposed off in the environment without proper treatment. Bench-scale laboratory experiments were conducted to develop a process scheme to fix the fluorides as non-leachable solid waste and fluoride free treated liquid waste for their disposal. To optimize the important parameters, simulated synthetic and actual wastes were used. For this study, three waste streams were collected from Nuclear Fuel Complex, Hyderabad. (author). 6 tabs., 1 fig.

Treatment of radioactive wastes containing plutonium

International Nuclear Information System (INIS)

Orlando, O.S.; Aparicio, G.; Greco, L.; Orosco, E.H.; Cassaniti, P.; Salguero, D.; Toubes, B.; Perez, A.E.; Menghini, J.E.; Esteban, A.; Adelfang, P.

1987-01-01

The radioactive wastes generated in the process of manufacture and control of experimental fuel rods of mixed oxides, (U,Pu)O 2 , require an specific treatment due to the plutonium content. The composition of liquid wastes, mostly arising from chemical checks, is variable. The salt content, the acidity, and the plutonium and uranium content are different, which makes necessary a chemical treatment before the inclusion in concrete. The solid waste, such as neoprene gloves, PVC sleeves, filter paper, disposable or broken laboratory material, etc. are also included in concrete. In this report the methods used to dispose of wastes at Alpha Facility are described. With regard to the liquid wastes, the glove box built to process them is detailed, as well as the applied chemical treatment, including neutralization, filtration and later solidification. As for the solid wastes, it is described the cementation method consisting in introducing them into an expanded metal matrix, of the basket type, that contains as a concentric drum of 200 liter capacity which is smaller than the matrix, and the filling with wet cement mortar. (Author)

Conditioning of uranium-containing technological radioactive waste

International Nuclear Information System (INIS)

Smodis, B.; Tavcar, G.; Stepisnik, M.; Pucelj, B.

2006-01-01

Conditioning of mostly liquid uranium containing technological radioactive waste emerging from the past research activities at the Jozef Stefan Institute is described. The waste was first thoroughly characterised, then the radionuclides present solidified by appropriate chemical treatment, and the final product separated and prepared for storage in compliance with the legislation. The activities were carried out within the recently renewed Hot Cells Facility of the Jozef Stefan Institute and the overall process resulted in substantial volume reduction of the waste initially present. (author)

Mixed Waste Integrated Program: A technology assessment for mercury-containing mixed wastes

International Nuclear Information System (INIS)

Perona, J.J.; Brown, C.H.

1993-03-01

The treatment of mixed wastes must meet US Environmental Protection Agency (EPA) standards for chemically hazardous species and also must provide adequate control of the radioactive species. The US Department of Energy (DOE) Office of Technology Development established the Mixed Waste Integrated Program (MWIP) to develop mixed-waste treatment technology in support of the Mixed Low-Level Waste Program. Many DOE mixed-waste streams contain mercury. This report is an assessment of current state-of-the-art technologies for mercury separations from solids, liquids, and gases. A total of 19 technologies were assessed. This project is funded through the Chemical-Physical Technology Support Group of the MWIP

Program for certification of waste from contained firing facility: Establishment of waste as non-reactive and discussion of potential waste generation problems

International Nuclear Information System (INIS)

Green, L.; Garza, R.; Maienschein, J.; Pruneda, C.

1997-01-01

Debris from explosives testing in a shot tank that contains 4 weight percent or less of explosive is shown to be non-reactive under the specified testing protocol in the Code of Federal Regulations. This debris can then be regarded as a non-hazardous waste on the basis of reactivity, when collected and packaged in a specified manner. If it is contaminated with radioactive components (e.g. depleted uranium), it can therefore be disposed of as radioactive waste or mixed waste, as appropriate (note that debris may contain other materials that render it hazardous, such as beryllium). We also discuss potential waste generation issues in contained firing operations that are applicable to the planned new Contained Firing Facility (CFF). The goal of this program is to develop and document conditions under which shot debris from the planned Contained Firing Facility (CFF) can be handled, shipped, and accepted for waste disposal as non-reactive radioactive or mixed waste. This report fulfills the following requirements as established at the outset of the program: 1. Establish through testing the maximum level of explosive that can be in a waste and still have it certified as non-reactive. 2. Develop the procedure to confirm the acceptability of radioactive-contaminated debris as non-reactive waste at radioactive waste disposal sites. 3. Outline potential disposal protocols for different CFF scenarios (e.g. misfires with scattered explosive)

Predicting the Lifetimes of Nuclear Waste Containers

Science.gov (United States)

King, Fraser

2014-03-01

As for many aspects of the disposal of nuclear waste, the greatest challenge we have in the study of container materials is the prediction of the long-term performance over periods of tens to hundreds of thousands of years. Various methods have been used for predicting the lifetime of containers for the disposal of high-level waste or spent fuel in deep geological repositories. Both mechanical and corrosion-related failure mechanisms need to be considered, although until recently the interactions of mechanical and corrosion degradation modes have not been considered in detail. Failure from mechanical degradation modes has tended to be treated through suitable container design. In comparison, the inevitable loss of container integrity due to corrosion has been treated by developing specific corrosion models. The most important aspect, however, is to be able to justify the long-term predictions by demonstrating a mechanistic understanding of the various degradation modes.

Process for treatment of detergent-containing radioactive liquid wastes

International Nuclear Information System (INIS)

Kamiya, K.; Chino, K.; Funabashi, K.; Horiuchi, S.; Motojima, K.

1984-01-01

A detergent-containing radioactive liquid waste originating from atomic power plants is concentrated to have about 10 wt. % detergent concentration, then dried in a thin film evaporator, and converted into powder. Powdered activated carbon is added to the radioactive waste in advance to prevent the liquid waste from foaming in the evaporator by the action of surface active agents contained in the detergent. The activated carbon is added in accordance with the COD concentration of the radioactive liquid waste to be treated, and usually at a concentration 2-4 times as large as the COD concentration of the liquid waste to be treated. A powdery product having a moisture content of not more than 15 wt. % is obtained from the evaporator, and pelletized and then packed into drums to be stored for a predetermined period

IMPROVEMENTS IN CONTAINER MANAGEMENT OF TRANSURANIC (TRU) AND LOW LEVEL RADIOACTIVE WASTE STORED AT THE CENTRAL WASTE COMPLEX (CWC) AT HANFORD

International Nuclear Information System (INIS)

UYTIOCO EM

2007-01-01

The Central Waste Complex (CWC) is the interim storage facility for Resource Conservation and Recovery Act (RCRA) mixed waste, transuranic waste, transuranic mixed waste, low-level and low-level mixed radioactive waste at the Department of Energy's (DOE'S) Hanford Site. The majority of the waste stored at the facility is retrieved from the low-level burial grounds in the 200 West Area at the Site, with minor quantities of newly generated waste from on-site and off-site waste generators. The CWC comprises 18 storage buildings that house 13,000 containers. Each waste container within the facility is scanned into its location by building, module, tier and position and the information is stored in a site-wide database. As waste is retrieved from the burial grounds, a preliminary non-destructive assay is performed to determine if the waste is transuranic (TRU) or low-level waste (LLW) and subsequently shipped to the CWC. In general, the TRU and LLW waste containers are stored in separate locations within the CWC, but the final disposition of each waste container is not known upon receipt. The final disposition of each waste container is determined by the appropriate program as process knowledge is applied and characterization data becomes available. Waste containers are stored within the CWC based on their physical chemical and radiological hazards. Further segregation within each building is done by container size (55-gallon, 85-gallon, Standard Waste Box) and waste stream. Due to this waste storage scheme, assembling waste containers for shipment out of the CWC has been time consuming and labor intensive. Qualitatively, the ratio of containers moved to containers in the outgoing shipment has been excessively high, which correlates to additional worker exposure, shipment delays, and operational inefficiencies. These inefficiencies impacted the LLW Program's ability to meet commitments established by the Tri-Party Agreement, an agreement between the State of Washington

Treatment of waste water miscible cutting fluids in automobile manufacturing; Jidosha kogyo ni okeru suiyosei sessakuyuzai no haieki shori

Energy Technology Data Exchange (ETDEWEB)

Ono, H. [Yushiro Chemical Industry Co. Ltd., Tokyo (Japan)

1995-09-01

Water-soluble cutting fluids are able to be used for several months to several years if the proper periodical management is carried out. However, the used solution should be treated as waste water when the function-recovery thereof becomes remarkable difficult. On this occasion, the treated solution (drainage) ought to meet the environmental standards prescribed for the purpose of protecting globe environment. Many cases in Japan are that the strict rules are set by each urban and rural prefectures addition to the government ordinance. For carrying out the treatment of waste water efficiently, it is necessary to construct the treating system by mastering the characteristics of waste water and selecting the most suitable one from numerous treating methods. In this paper, after the description on the water-polluting substances and drainage standards, the general treating method of waste water miscible cutting fluids is described. Finally, the concrete cases with respect to the treatment of waste water treatment in automobile manufacturing factories are introduced. 5 refs., 5 figs., 5 tabs.

Heat transfer effects in vertically emplaced high level nuclear waste container

International Nuclear Information System (INIS)

Moujaes, S.F.; Lei, Y.M.

1994-01-01

Modeling free convection heat transfer in an cylindrical annular enclosure is still an active area of research and an important problem to be addressed in the high level nuclear waste repository. For the vertically emplaced waste container, the air gap which is between the container shell and the rock borehole, have an important role of dissipating heat to surrounding rack. These waste containers are vertically emplaced in the borehole 300 meters below ground, and in a horizontal grid of 30 x 8 meters apart. The borehole will be capped after the container emplacement. The expected initial heat generated is between 3--4.74 kW per container depending on the type of waste. The goal of this study is to use a computer simulation model to find the borehole wall, air-gap and the container outer wall temperature distributions

The Treatment of Mixed Waste with GeoMelt In-Container Vitrification

International Nuclear Information System (INIS)

Finucane, K.G.; Campbell, B.E.

2006-01-01

AMEC's GeoMelt R In-Container Vitrification (ICV) TM has been used to treat diverse types of mixed low-level radioactive waste. ICV is effective in the treatment of mixed wastes containing polychlorinated biphenyls (PCBs) and other semi-volatile organic compounds, volatile organic compounds (VOCs) and heavy metals. The GeoMelt vitrification process destroys organic compounds and immobilizes metals and radionuclides in an extremely durable glass waste form. The process is flexible allowing for treatment of aqueous, oily, and solid mixed waste, including contaminated soil. In 2004, ICV was used to treat mixed radioactive waste sludge containing PCBs generated from a commercial cleanup project regulated by the Toxic Substances Control Act (TSCA), and to treat contaminated soil from Rocky Flats Environmental Technology Site. The Rocky Flats soil contained cadmium, PCBs, and depleted uranium. In 2005, AMEC completed a treatability demonstration of the ICV technology on Mock High Explosive from Sandia National Laboratories. This paper summarizes results from these mixed waste treatment projects. (authors)

Decontamination of organic wastes containing radionuclides

International Nuclear Information System (INIS)

Unsworth, T.J.; Pimblott, S.M.; Brown, N.W.

2015-01-01

An electrochemical oxidation treatment has been developed by Arvia Technology for organic wastes containing radionuclides, in which GIC-bisulphate is used as an adsorbent and electrode. Significant work has been carried out in the irradiation of graphite for medical and nuclear applications and in the use of carbonaceous adsorbents but knowledge of the applicability of graphite intercalation compounds (GICs) in these roles is limited. This project will attempt to fill this gap. It will investigate the suitability of GIC-bisulphate as an adsorbent in an electrochemical treatment process for radioactive organic liquids. The process was initially used to treat waste-water from non-nuclear operations and now requires technical knowledge and research to adapt the treatment for the nuclear industry. Adsorption processes involving organic wastes containing mobile radionuclides such as 137 Cs are difficult to understand. The effects of gamma radiation on the chemistry of water and organics could complicate the treatment process further. To ensure the suitability and effectiveness of the electrochemical oxidation treatment for radioactive organic wastes, the following effects are being investigated: -) radiolytic degradation of GIC-bisulphate in solution, -) leaching of intercalated ions due to gamma radiation, -) effect of gamma radiation on the adsorption of organics by GIC-bisulphate, -) changes in the sorption behaviour of radioactive contaminants, -) distribution coefficients of contaminants in organic and aqueous phases, and -) selective or competitive adsorption on graphite surface sites

Organic waste process containing at least one radioactive element

International Nuclear Information System (INIS)

Le Roy, F.

1977-01-01

The description is given of an organic waste process containing at least one element from the group comprising strontium, cesium, iodine and ruthenium. It comprises the introduction of the organic waste and gaseous oxygen in a bath of melted salt containing an alkaline carbonate, the bath being maintained at a high temperature between 400 and 1000 0 C and at a pressure of 0.5 to 10 bars, so that the organic waste is burnt and oxidised at least partly, the element selected being retained by the bath of melted salt [fr

Sulphate in Liquid Nuclear Waste: from Production to Containment

Energy Technology Data Exchange (ETDEWEB)

Lenoir, M.; Grandjean, A.; Ledieu, A.; Dussossoy, J.L.; Cau Dit Coumes, C.; Barre, Y.; Tronche, E. [CEA Marcoule, DEN/DTCD/SECM/LDMC, Batiment 208 BP17171, Bagnols sur Ceze, 30207 (France)

2009-06-15

Nuclear industry produces a wide range of low and intermediate level liquid radioactive wastes which can include different radionuclides such as {sup 90}Sr. In La Hague reprocessing plant and in the nuclear research centers of CEA (Commissariat a l'Energie Atomique), the coprecipitation of strontium with barium sulphate is the technique used to treat selectively these contaminated streams with the best efficiency. After the decontamination process, low and intermediate level activity wastes incorporating significant quantities of sulphate are obtained. The challenge is to find a matrix easy to form and with a good chemical durability which is able to confine this kind of nuclear waste. The current process used to contain sulphate-rich nuclear wastes is bituminization. However, in order to improve properties of containment matrices and simplify the process, CEA has chosen to supervise researches on other materials such as cements or glasses. Indeed, cements are widely used for the immobilization of a variety of wastes (low and intermediate level wastes) and they may be an alternative matrix to bitumen. Even if Portland cement, which is extensively used in the nuclear industry, presents some disadvantages for the containment of sulphate-rich nuclear wastes (risk of swelling and cracking due to delayed ettringite formation), other cement systems, such as calcium sulfo-aluminate binders, may be valuable candidates. Another matrix to confine sulphate-rich waste could be the glass. One of the advantages of this material is that it could also immobilize sulphate containing high level nuclear waste which is present in some countries. This waste comes from the use of ferrous sulfamate as a reducing agent for the conversion of Pu{sup 4+} to Pu{sup 3+} in the partitioning stage of the actinides during reprocessing. Sulphate solubility in borosilicate glasses has already been studied in CEA at laboratory and pilot scales. At a pilot scale, low level liquid waste has been

Concrete containers in radioactive waste management: a review

Energy Technology Data Exchange (ETDEWEB)

Tavares, Bárbara L.; Tello, Clédola Cássia O. de, E-mail: barbaralacerdat@gmail.com [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte/MG (Brazil)

2017-07-01

Nuclear power is considered a clean energy, because it does not produce the gases responsible for greenhouse effect. However, like all human activities, it is susceptible to waste generation. With increasing demand for energy in Brazil, the use of nuclear power is being expanded, as a result, the implementation of correct treatment and disposal are a necessity, in order to ensure the non-contamination of the public or environment and that exposure doses are lower than limits by legislation. Most of waste produced in Brazil are classified as low and intermediate radiation level; consequently, the national repository will be near surface, in accordance with the legislation. Considering the multi-barrier concept for the repository, the radioactive waste product is the first barrier. To have a qualified radioactive waste product, it should be solid or solidified using an inert material. With the intention of standardize the disposal process, all radioactive waste products will be placed in concrete containers. These containers will be settled in a concrete cell, the final engineered barrier of the repository. The state of the art is the first part of the study of the concrete containers and its specific criteria acceptation. Since the repository’s operational and surveillance period is 60 and 300 years, respectively, tests still need to be fulfilled in order to ensure the stability and resistance of the material. (author)

Concrete containers in radioactive waste management: a review

International Nuclear Information System (INIS)

Tavares, Bárbara L.; Tello, Clédola Cássia O. de

2017-01-01

Nuclear power is considered a clean energy, because it does not produce the gases responsible for greenhouse effect. However, like all human activities, it is susceptible to waste generation. With increasing demand for energy in Brazil, the use of nuclear power is being expanded, as a result, the implementation of correct treatment and disposal are a necessity, in order to ensure the non-contamination of the public or environment and that exposure doses are lower than limits by legislation. Most of waste produced in Brazil are classified as low and intermediate radiation level; consequently, the national repository will be near surface, in accordance with the legislation. Considering the multi-barrier concept for the repository, the radioactive waste product is the first barrier. To have a qualified radioactive waste product, it should be solid or solidified using an inert material. With the intention of standardize the disposal process, all radioactive waste products will be placed in concrete containers. These containers will be settled in a concrete cell, the final engineered barrier of the repository. The state of the art is the first part of the study of the concrete containers and its specific criteria acceptation. Since the repository’s operational and surveillance period is 60 and 300 years, respectively, tests still need to be fulfilled in order to ensure the stability and resistance of the material. (author)

User's manual for remote-handled transuranic waste container welding and inspection fixture

International Nuclear Information System (INIS)

Hauptmann, J.P.

1985-09-01

Rockwell Hanford Operations (Rockwell) has designed built, and tested a prototype remotely operated welding and inspection fixture to be used in making the closure weld on the remote-handled transuranic (RH-TRU) waste container. The RH-TRU waste container has an average TRU concentration in excess of 100 nCi/gm, and a surface radiation dose rate in excess of 200 mrem/h, but not exceeding 100 rem/h. The RH-TRU waste container is to be used by defense waste generator sites in the United States for final packaging of RH-TRU wastes and is compatible with the requirements of the Waste Isolation Pilot Plant (WIPP) and the WIPP handling system. Standard and stacked RH-TRU container designs are available. The standard container is 26 in. in dia. by 121 in. high; the stacked containers are 26 in. in dia. by 61.25 in. high. After loading, two stacked containers are fitted and welded together to form the identical measurements of the standard 121-in. container. The prototype RH-TRU waste container welding and inspection fixture was intended for test and evaluation only, and not for installation in an operating facility. The final RH-TRU waste container welding and inspection fixture drawings (see appendix) incorporate several changes made following operational testing of the original fixture. These modifications are identified in this manual. However, not all modifications have been functionally tested. The purpose of this manual is to aid waste generator sites in designing a remotely operated welding and inspection fixture that will conform to their own requirements. Modifications to the Rockwell design must be evaluated for structural and WIPP handling requirements. This manual also provides design philosophy, component vendor information, and cost estimates

Treatment of organic waste solutions containing tributyl phosphate

International Nuclear Information System (INIS)

Drobnik, S.

The two processes developed in the laboratory for treating waste solutions containing TBP, namely TBP separation with phosphoric acid and saponification were tested on a semi-industrial scale. A waste solution from the first phase of the Karlsruhe reprocessing plant was used

Containment and stabilization technologies for mixed hazardous and radioactive wastes

International Nuclear Information System (INIS)

Buelt, J.L.

1993-05-01

A prevalent approach to the cleanup of waste sites contaminated with hazardous chemicals and radionuclides is to contain and/or stabilize wastes within the site. Stabilization involves treating the wastes in some fashion, either in situ or above ground after retrieval, to reduce the leachability and release rate of waste constituents to the environment. This approach is generally reserved for radionuclide contaminants, inorganic hazardous contaminants such as heavy metals, and nonvolatile organic contaminants. This paper describes the recent developments in the technical options available for containing and stabilizing wastes. A brief description of each technology is given along with a discussion of the most recent developments and examples of useful applications

Degradation of Remazol Red in batik dye waste water by contact glow discharge electrolysis method using NaOH and NaCl electrolytes

Science.gov (United States)

Saksono, Nelson; Putri, Dita Amelia; Suminar, Dian Ratna

2017-03-01

Contact Glow Discharge Electrolysis (CGDE) method is one of Plasma Electrolysis technology which has been approved to degrade organic waste water because it is very productive in producing hydroxyl radical. This study aims to degrade Remazol Red by CGDE method and evaluate important parameters that have influent in degradation process of Remazol Red in Batik dye waste water in batch system. The kind of electrolyte (acid and base) and the addition of metal ion such as Fe2+ have affected Remazol Red degradation percentage. Ultraviolet-Visible (UV-Vis) absorption spectra were used to monitor the degradation process. The result of study showed that percentage degradation was 99.97% which obtained by using NaCl 0.02 M with addition Fe2+ 20 ppm, applied voltage 700 volt, anode depth 0.5 cm, initial concentration of Remazol Red 250 ppm and the temperature of solutions was maintained 50-60 ˚C.

Precipitation and Deposition of Aluminum-Containing Phases in Tank Wastes

International Nuclear Information System (INIS)

Dabbs, Daniel M.; Aksay, Ilhan A.

2005-01-01

Aluminum-containing phases compose the bulk of solids precipitating during the processing of radioactive tank wastes. Processes designed to minimize the volume of high-level waste through conversion to glassy phases require transporting waste solutions near-saturated with aluminum-containing species from holding tank to processing center. The uncontrolled precipitation within transfer lines results in clogged pipes and lines and fouled ion exchangers, with the potential to shut down processing operations

Plutonium waste container identification

International Nuclear Information System (INIS)

Schmierer, T.J.

1979-01-01

The purpose of this paper is to define the parameters of a method for identifying plutonium waste containers. This information will form the basis for a permanent committee to develop a complete identification program for use throughout the world. Although a large portion of the information will be on handwritten notebooks and may not be as extensive as is desired, it will all be helpful. The final information will be programmed into computer language and be available to all interested parties as well as a central control committee which will have the expertise to provide each government with advice on the packaging, storage, and measurement of the waste for which it is responsible. As time progresses, this central control committee should develop permanent storage sites and establish a system of records which will last for hundreds of years

Los Alamos Transuranic Waste Size Reduction Facility

International Nuclear Information System (INIS)

Harper, J.; Warren, J.

1987-01-01

The Los Alamos Transuranic (TRU) Waste Size Reduction Facility (SRF) is a production oriented prototype completed in 1981 and later modified during 1986 to enhance production. The facility is operated to remotely cut (with a plasma arc torch) and repackage TRU contaminated metallic wastes (e.g., glove boxes, ducting and pipes) for eventual disposal at the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico. The resulting flat sections are packaged into a tested Department of Transportation Type 7A metal container. To date, the facility has successfully processed stainless steel glove boxes (with and without lead shielding construction) and retention tanks. It was found that used glove boxes generate more cutting fumes than do unused glove boxes or metal plates - possibly due to deeply embedded chemical residues from years of service. Water used as a secondary fluid with the plasma arc cutting system significantly reduces visible fume generation during the cutting of used glove boxes and lead-lined glove boxes

Possible combustion hazards in 3013 plutonium waste container

International Nuclear Information System (INIS)

Sherman, M.P.

1999-01-01

Are there combustion hazards in plutonium-contaminated waste containers caused by combustible gas generation? Current gas generation models in which the only reaction considered is radiolysis must inevitably predict eventual complete dissociation of any water present into hydrogen and oxygen. Waste prepared for the 3013 container should be less subject to this problem because organic material and most of the absorbed water should have been removed. Depending on the waste form, moisture content, organic content, temperature, and container material, the pressure rise due to gas generation will be bounded by backreactions, recombination of the hydrogen and oxygen, absorption of the oxygen by plutonium oxide, and possibly other chemical reactions. Examination of a variety of food pack waste containers at Los Alamos National Laboratory (LANL) has shown little pressure rise, indeed often subatmospheric pressures. In a few cases large hydrogen concentrations up to 47% mole fraction were observed, but with negligible oxygen content. The only fuel seen in significant quantities was H 2 and, in one case, CO; the only oxidizer seen in significant quantities was O 2 . Considerable work on measuring gas generation is being done at Westinghouse Savannah River Company and LANL. In a mixture of H 2 , O 2 , and other diluent gases, if the hydrogen concentration is below the value at the lean flammability limit, or if the oxygen concentration is below that at the rich flammability limit, a flame will not propagate from an ignition source. Assuming H 2 is the only fuel present in significant quantities, a mixture leaner than the lean limit will get only leaner if mixed with air and is therefore no combustion hazard. However, when a mixture containing large amounts of H 2 is nonflammable because there is insufficient O 2 , there is a hazard. If the mixture should leak into a volume containing O 2 , or the container is opened into the surrounding air, the mixture will pass through the

Open site tests on corrosion of carbon steel containers for radioactive waste forms

International Nuclear Information System (INIS)

Barinov, A.S.; Ojovan, M.I.; Ojovan, N.V.; Startceva, I.V.; Chujkova, G.N.

1999-01-01

Testing of waste containers under open field conditions is a component part of the research program that is being carried out at SIA Radon for more than 20 years to understand the long-term behavior of radioactive waste forms and waste packages. This paper presents the preliminary results of these ongoing studies. The authors used a typical NPP operational waste, containing 137 Cs, 134 Cs, and 60 Co as the dominant radioactive constituents. Bituminized and vitrified waste samples with 30--50 wt.% waste loading were prepared. Combined effects of climatic factors on corrosion behavior of carbon steel containers were estimated using gravimetric and chemical analyses. The observations suggest that uniform corrosion of containers prevails under open field conditions. The upper limits for the lifetime of containers were derived from calculations based on the model of atmospheric steel corrosion. Estimated lifetime values range from 300 to 600 years for carbon steel containers with the wall thickness of 2 mm containing vitrified waste, and from 450 to 500 years for containers with the wall thickness of 2.5 mm that were used for bituminized waste. However, following the most conservative method, pitting corrosion may cause container integrity failure after 60 to 90 years of exposure

Neutralization of Hydroxide Ion in Melt-Grown NaCl Crystals

Science.gov (United States)

Otterson, Dumas A.

1961-01-01

Many recent studies of solid-state phenomena, particularly in the area of crystal imperfections, have involved the use of melt-grown NaCl single crystals. Quite often trace impurities in these materials have had a prominent effect on these phenomena. Trace amounts of hydroxide ion have been found in melt-grown NaCl crystals. This paper describes a nondestructive method of neutralizing the hydroxide ion in such crystals. Crystals of similar hydroxide content are maintained at an elevated temperature below the melting point of NaCl in a flowing atmosphere containing. dry hydrogen chloride. Heat treatment is continued until an analysis of the test specimens shows no excess hydroxide ion. A colorimetric method previously described4 is used for this analysis.

Storage container for radioactive wastes

International Nuclear Information System (INIS)

Catalayoud, L.; Gerard, M.

1990-01-01

Tightness, shock resistance and corrosion resistance of containers for storage of radioactive wastes it obtained by complete fabrication with concrete reinforced with metal fibers. This material is used for molding the cask, the cover and the joint connecting both parts. Dovetail grooves are provided on the cask and the cover for the closure [fr

Evolution of thermoelectric performance for (Bi,Sb)2Te3 alloys from cutting waste powders to bulks with high figure of merit

International Nuclear Information System (INIS)

Fan, Xi'an; Cai, Xin zhi; Han, Xue wu; Zhang, Cheng cheng

2016-01-01

Bi 2 Te 3 based cutting waste powders from cutting wafers were firstly selected as raw materials to prepare p-type Bi 2 Te 3 based thermoelectric (TE) materials. Through washing, reducing, composition correction, smelting and resistance pressing sintering (RPS) process, p-type (Bi,Sb) 2 Te 3 alloy bulks with different nominal stoichiometries were successfully obtained. The evolution of microstructure and TE performance for (Bi,Sb) 2 Te 3 alloys were investigated in detail. All evidences confirmed that most of contaminants from line cutting process such as cutting fluid and oxides of Bi, Sb or Te could be removed by washing, reducing and smelting process used in this work. The carrier content and corresponding TE properties could be adjusted effectively by appropriate composition correction treatment. At lastly, a bulk with a nominal stoichiometry of Bi 0.44 Sb 1.56 Te 3 was obtained and its' dimensionless figure of merit (ZT) was about 1.16 at 90 °C. The ZT values of Bi 0.36 Sb 1.64 Te 3 and Bi 0.4 Sb 1.6 Te 3 alloy bulks could also reach 0.98 and 1.08, respectively. Different from the conventional recycling technology such as hydrometallurgy extraction methods, the separation and extraction of beneficial elements such as Bi, Sb and Te did not need to be performed and the Bi 2 Te 3 based bulks with high TE properties could be directly obtained from the cutting waste powders. In addition, the recycling technology introduced here was green and more suitable for practical industrial application. It can improve material utilization and lower raw material costs of manufacturers. - Graphical abstract: Three kinds of typical morphologies for the fractographs: typical lamellar structure, agglomerated submicron-sized granules and dispersed cubic particles from the initial cutting waste powders. - Highlights: • Bi 2 Te 3 based wastes were directly selected as raw materials for TE alloys. • Contaminants from cutting fluid and oxides could be effectively removed. �

Generalized waste package containment model

International Nuclear Information System (INIS)

Liebetrau, A.M.; Apted, M.J.

1985-02-01

The US Department of Energy (DOE) is developing a performance assessment strategy to demonstrate compliance with standards and technical requirements of the Environmental Protection Agency (EPA) and the Nuclear Regulatory Commission (NRC) for the permanent disposal of high-level nuclear wastes in geologic repositories. One aspect of this strategy is the development of a unified performance model of the entire geologic repository system. Details of a generalized waste package containment (WPC) model and its relationship with other components of an overall repository model are presented in this paper. The WPC model provides stochastically determined estimates of the distributions of times-to-failure of the barriers of a waste package by various corrosion mechanisms and degradation processes. The model consists of a series of modules which employ various combinations of stochastic (probabilistic) and mechanistic process models, and which are individually designed to reflect the current state of knowledge. The WPC model is designed not only to take account of various site-specific conditions and processes, but also to deal with a wide range of site, repository, and waste package configurations. 11 refs., 3 figs., 2 tabs

A probabilistic approach to assessing radioactive waste container lifetimes

International Nuclear Information System (INIS)

Porter, F.M.; Naish, C.C.; Sharland, S.M.

1994-01-01

A general methodology has been developed to make assessments of the lifetime of specific radioactive waste container designs in a repository environment. The methodology employs a statistical approach, which aims to reflect uncertainty in the corrosion rates, and the evolution of the environmental conditions. In this paper, the methodology is demonstrated for an intermediate-level waste (ILW) container in the anticipated UK repository situation

How reliable does the waste package containment have to be

International Nuclear Information System (INIS)

Wick, E.A.

1985-01-01

The final rule (10 CFR Part 60) for Disposal of High-Level Radioactive Wastes in Geologic Repositories specifies that the engineered barrier system shall be designed so that, assuming anticipated processes and events, containment of high-level radioactive wastes (HLW) will be substantially complete during the period when radiation and thermal conditions in the engineered barrier system are dominated by fission product decay. This requirement leads to the Nuclear Regulatory Commission (NRC) being asked the following questions: What is meant by ''substantially complete''. How reliable does waste package containment have to be. How many waste packages can fail. Although the NRC has not defined quantitatively the term ''substantially complete'', a numerical concept for acceptable release during the containment period is discussed. The number of containment failures that could be tolerated under the rule would depend upon the acceptable release, the time at which failure occurs and the rate of release from a failed package

Mathematical models for diffusive mass transfer from waste package container with multiple perforations

International Nuclear Information System (INIS)

Lee, J.H.; Andrews, R.W.; Chambre, P.L.

1996-01-01

A robust engineered barrier system (EBS) is employed in the current design concept for the potential high-level nuclear waste repository at Yucca Mountain, Nevada, US. The primary component of the EBS is a multi-barrier waste package container. Simplifying the geometry of the cylindrical waste package container and the underlying invert into the equivalent spherical configuration, mathematical models are developed for steady-state and transient diffusive releases from the failed waste container with multiple perforations (or pit penetrations) at the boundary of the invert. Using the models the steady-state and transient diffusive release behaviors form the failed waste container are studied. The analyses show that the number of perforations, the size of perforation, the container wall thickness, the geometry of the waste container and invert, and the adsorption of radionuclide in the invert are the important parameters that control the diffusive release rate. It is emphasized that the failed (or perforated) waste package container can still perform as a potentially important barrier (or diffusion barrier) to radionuclide release

Synthesis of studies on primary containers for MLA-VL wastes

International Nuclear Information System (INIS)

Bart, F.; Delassale, F.; Rey, F.; Helie, M.; Levoy, R.; Moitrier, C.; Sicardy, O.; Tiquet, P.

2004-01-01

The aim of this study is the presentation of studies realized on primary containers of medium activity long life level. These studies are realized in the framework of the axis 3 of the law of 1991 on the radioactive waste management. The specificity of this document is the presentation of container for ''random'' wastes chemically corrosive in order to complete the range of possible packages. Thus a special program has been developed to demonstrate a conditioning solution which offers to the waste producers a possibility of conditioning these wastes without a preliminary treatment. (A.L.B.)

Lining materials for waste disposal containment and waste storage facilities. (Latest citations from the NTIS bibliographic database). Published Search

International Nuclear Information System (INIS)

1993-11-01

The bibliography contains citations concerning the design characteristics, performance, and materials used to make liners for the waste disposal and storage industry. Liners made of concrete, polymeric materials, compacted clays, asphalt, and in-situ glass are discussed. The use of these liners to contain municipal wastes, hazardous waste liquids, and both low-level and high-level radioactive wastes is presented. Liner permeability, transport, stability, construction, and design are studied. Laboratory field measurements for specific wastes are included. (Contains a minimum of 213 citations and includes a subject term index and title list.)

A Combinatorial Benders’ Cuts Algorithm for the Local Container Drayage Problem

Directory of Open Access Journals (Sweden)

Zhaojie Xue

2015-01-01

Full Text Available This paper examines the local container drayage problem under a special operation mode in which tractors and trailers can be separated; that is, tractors can be assigned to a new task at another location while trailers with containers are waiting for packing or unpacking. Meanwhile, the strategy of sharing empty containers between different customers is also considered to improve the efficiency and lower the operation cost. The problem is formulated as a vehicle routing and scheduling problem with temporal constraints. We adopt combinatorial benders’ cuts algorithm to solve this problem. Numerical experiments are performed on a group of randomly generated instances to test the performance of the proposed algorithm.

Solid waste containing method and solid waste container

International Nuclear Information System (INIS)

Sawai, Takeshi.

1997-01-01

Solid wastes are filled in a sealed vessel, and support spacers are inserted to the gap between the inner wall of a vessel main body and the solid wastes. The solid wastes comprise shorn pieces (crushed pieces) of spent fuel rod cladding tubes, radioactively contaminated metal pieces and miscellaneous solids pressed into a disk-like shape. The sealed vessel comprises, for example, a stainless steel. The solid wastes are filled while being stacked in a plurality of stages. A solidifying filler is filled into the gap between the inner wall and the solid wastes in the vessel main body by way of an upper opening, and the upper opening is closed by a closing lid to provide an entirely sealed state. Alumina particles having high heat conductivity and excellent heat durability are used for the solid filler. It is preferable to fill an inert gas such as a dried nitrogen gas in the sealed vessel. (I.N.)

Pretreatment method for radioactive iodine-containing liquid wastes and pretreatment device

International Nuclear Information System (INIS)

Wakaida, Yasuo.

1996-01-01

Heretofore, radioactive iodine-containing liquid wastes have been discharged directly to a storing and decaying storage vessel to conduct a water draining treatment. In the present invention, the radioactive iodine-containing liquid wastes to be discharged are not discharged to the storage vessel directly but injected to a filling tank, as a pretreatment, to distinguish whether proteins are mixed in the liquid wastes or not. When proteins are mixed, miscellaneous materials such as proteins are recovered and removed by a protein processing system. When proteins are not mixed, radioactive iodine is recovered and removed directly by an iodine processing system. With such procedures, water draining treatment in the storing and decaying storage vessel is mitigated, and even when the amount of the radioactive iodine-containing liquid wastes is increased, the existent maintaining and decaying storage vessel can be used as it is. Accordingly, a safe water draining treatment with good efficiency can be conducted relative to radioactive iodine-containing liquid wastes at a reduced cost. (T.M.)

Device for safe disposal of non-utilizable cuttings from depleted uranium metal

International Nuclear Information System (INIS)

Fiala, B.

1991-01-01

A device was developed for the production of U 3 O 8 from cuttings of depleted uranium metal or of uranium metal waste whose surface area is sufficiently large for combustion. The waste may contain organic impurities or other metals. The purity of the U 3 O 8 thus obtained is about 98%. Tests gave evidence that the combustion facility meets all requirements set forth by hygienic and ecological regulations. (Z.M.). 1 fig

Method for solidification of radioactive iodine-containing solid wastes

International Nuclear Information System (INIS)

Ozawa, Yoshihiro; Funabashi, Kiyomi; Uetake, Naoto.

1987-01-01

Purpose: To process radioactive iodine containing solid wastes as non-leaching solidified wastes with no risk of iodine release. Method: It has been known for the thermal stability of CuI, PbI 2 or adsorbents containing the same that they do not release iodine in an inert gas atmosphere or in a reducing atmosphere at a temperature lower than 480 deg C. In view of the above, adsorbents containing iodine in the chemical form of CuI or PbI 2 , or CuI or powdery PbI 2 per se are sealed and solidified into low melting glass at a temperature of lower than 480 deg C at which no iodine release occurs in a non-oxidative atmosphere. Since the products are vitrified wastes, they scarcely show leaching property and are excellent in durability and stability. (Takahashi, M.)

Effect of Water Content, Temperature and NaCl on CO2 Corrosion of Carbon Steel (A106B in Iraqi Crude Oil

Directory of Open Access Journals (Sweden)

Saad Ahmed Jafar

2018-01-01

Full Text Available An investigation was carried out to determine the corrosion rate of carbon steel (A 106 GradeB as flow line in crude oil production with CO2 content employing three Iraqi crude oil (Kirkuk crude oil, Halfaya crude oil, and Rumalia crude oil with identical produced water (brine [1%NaCl,2%NaCl, and 3%NaCl]. Experiments were performed in an autoclave test apparatus, crude oilproduced water mixtures, water cuts were (0, 10, 20, 30, 40, and 100%, and temperature (20, 40, 60°C. For all experiments, CO2 partial pressure was maintained at 4bar and rotational speed 500 rpm. The corrosion rates were determined by the weight loss method. The results revealed that the corrosion rate of carbon steel increased by increasing water cut and temperature, but decreased with increasing salt concentration for all types of crude oil. Rumaila crude oil exhibited the highest corrosion rate and Kirkuk crude oil exhibits the lowest corrosion rate while Halfaya crude oil exhibits a moderate corrosion rate.

Corrosion process studies in a nuclear waste container

International Nuclear Information System (INIS)

Guasp, Ruben A.; Lanzani, Liliana A.; Coronel, Pascual; Bruzzoni, Pablo; Semino, Carlos J.

1999-01-01

Latest results on corrosion behavior studies on high activity nuclear waste container are reported. Corrosion evaluation on lead base alloys and modeling to predict carbon steel external container cover generalized corrosion, are the main issues of these studies. (author)

Design criteria burial containers for non-transuranic solid radioactive waste

International Nuclear Information System (INIS)

Hammond, J.E.

1976-01-01

The criteria, replace HW-83959 and apply to containers constructed specifically for the containment of beta-gamma radioactively contaminated waste removed from an area controlled by radiation work procedures, transported across an uncontrolled area where there is risk of a radiation release to the environs, and buried in an approved radioactive waste burial ground

Final storage of radioactive waste in deep boreholes

International Nuclear Information System (INIS)

Eichmeyer, H.; Wolff, H.

1985-01-01

The plans of the Danish Atomic Energy Authority expect the storage of 4500 containers with high activity waste each weighing 15 tonnes in deep boreholes in rock salt over a period of 30 years. The Danish plans are concerned with the storage medium salt in one of the many salt mines in North Germany and Denmark with a depth of 1200 metres, because of the high plasticity, good thermal conductivity and non-permeability to liquids and gases. Eight deep boreholes with a diameter of 750 mm are provided in a circle of radius r=250 metres. With a deviation of 0 , the boreholes will be piped down to 1000 metres and after completion, will be filled with clay slurry and barium sulphate. At the start of storage of the waste in containers 6.8 metres long, the clay slurry is replaced by cement slurry with saturated NaCl solution. Another possibility is to fill the borehole volume with saturated NaCl solution, in order to let the convergence act on the annular space between the container and the borehole wall. After filling the borehole, the open borehole should be sealed over a distance of 200 metres with rock salt and over 50 metres with a concrete stopper. It is planned to provide a dense and corrosion-proof seal with bitumen above the concrete. (orig./GB) [de

The Welding Effect on Mechanical Strength of Low Level Radioactive Waste Drum Container

International Nuclear Information System (INIS)

Aisyah; Herlan Martono

2007-01-01

The treatment of compactable low level solid waste was started by compaction of 100 liter drum containing the waste using 600 kN hydraulic press in 200 liters drum. The 200 liter drum of waste container containing of compacted waste then immobilized with cement and stored in interm storage. The 200 liter drum of waste container made of carbon steel material to comply with a good mechanical strength request in order to be able to retain the waste content for long period. Welding is a one step in a waste drum container fabrication process that has an opportunity in decreasing these mechanical strength. The research is carried out by welding the waste drum container material sample by electric arc welding. Mechanical strength test carried out by measuring the tensile strength by using the tensile strength machine, hardness test by using Vickers hardness test and microstructure observation by using the optic microscope. The result shows that the welding cause the microstructure changes, its meaning of forming ferro oxide phase on welding area that leads to the brittle material, so that the mechanical strength has a decreasing slightly. Nevertheless the decreasing of mechanical strength is still in the range of safety limit. (author)

Proteins associated with adaptation of cultured tobacco cells to NaCl

International Nuclear Information System (INIS)

Singh, N.K.; Handa, A.K.; Hasegawa, P.M.; Bressan, R.A.

1985-01-01

Cultured tobacco cells (Nicotiana tabacum L. cv Wisconsin 38) adapted to grow in medium containing high levels of NaCl or polyethylene glycol (PEG) produce several new or enhanced polypeptide bands on sodium dodecyl sulfate-polyarylamide gel electrophoresis. The intensities of some of the polypeptide bands increase with increasing levels of NaCl adaptation, while the intensities of other polypeptide bands are reduced. Synthesis of 26-kilodalton polypeptide(s) occurs at two different periods during culture growth of NaCl adapted cells. Unadapted cells also incorporate 35 S into a 26-kilodalton polypeptide during the later stage of culture growth beginning at midlog phase. The 26-kilodalton polypeptides from adapted and unadapted cells have similar partial proteolysis peptide maps and are immunologically cross-reactive. During adaptation to NaCl, unadapted cells synthesize and accumulate a major 26-kilodalton polypeptide, and the beginning of synthesis corresponds to the period of osmotic adjustment and culture growth. From their results, the authors suggest an involvement of the 26-kilodalton polypeptide in the adaptation of cultured tobacco cells to NaCl and water stress. 38 references, 11 figures, 2 tables

Immobilization of INEL low-level radioactive wastes in ceramic containment materials

International Nuclear Information System (INIS)

Seymour, W.C.; Kelsey, P.V.

1978-11-01

INEL low-level radioactive wastes have an overall chemical composition that lends itself to self-containment in a ceramic-based material. Fewer chemical additives would be needed to process the wastes than to process high-level wastes or use a mixture containment method. The resulting forms of waste material could include a basalt-type glass or glass ceramic and a ceramic-type brick. Expected leach resistance is discussed in relationshp to data found in the literature for these materials and appears encouraging. An overview of possible processing steps for the ceramic materials is presented

Management of hazardous waste containers and container storage areas under the Resource Conservation and Recovery Act

International Nuclear Information System (INIS)

1993-08-01

DOE's Office of Environmental Guidance, RCRA/CERCLA Division, has prepared this guidance document to assist waste management personnel in complying with the numerous and complex regulatory requirements associated with RCRA hazardous waste and radioactive mixed waste containers and container management areas. This document is designed using a systematic graphic approach that features detailed, step-by-step guidance and extensive references to additional relevant guidance materials. Diagrams, flowcharts, reference, and overview graphics accompany the narrative descriptions to illustrate and highlight the topics being discussed. Step-by-step narrative is accompanied by flowchart graphics in an easy-to-follow, ''roadmap'' format

Management of hazardous waste containers and container storage areas under the Resource Conservation and Recovery Act

Energy Technology Data Exchange (ETDEWEB)

1993-08-01

DOE`s Office of Environmental Guidance, RCRA/CERCLA Division, has prepared this guidance document to assist waste management personnel in complying with the numerous and complex regulatory requirements associated with RCRA hazardous waste and radioactive mixed waste containers and container management areas. This document is designed using a systematic graphic approach that features detailed, step-by-step guidance and extensive references to additional relevant guidance materials. Diagrams, flowcharts, reference, and overview graphics accompany the narrative descriptions to illustrate and highlight the topics being discussed. Step-by-step narrative is accompanied by flowchart graphics in an easy-to-follow, ``roadmap`` format.

Radioactive waste containment - a literature study

International Nuclear Information System (INIS)

Mohiuddin, G.

1985-01-01

One of the basic requirements of safe radioactive waste disposal is isolation of the radioactive substances to prevent leakage into the biosphere. The multi-barrier concept has been developed to meet this requirement. Within the framework of the concept, barriers can be either natural or man-made. Natural barriers, i.e. geologic formations,have been investigated for their suitability, with host rock and their different properties being determined and compared. It has been found that the qualification of a proposed repository medium cannot be defined on the basis of physical, chemical, and mineralogical criteria alone, but that these data have to be completed by a global evaluation of the entire system consisting of waste products and waste forms, host rock, and surrounding rock. The study in hand reviews the reports and also lists the studies made on engineered barriers, as e.g. immobilisation barriers, container and package barriers, of various waste forms. A review of the studies dealing with the various waste disposal techniques shows that the sub-surface waste disposal and the deep underground disposal in mines are the best developed techniques currently. A review of ultimate disposal concepts adopted abroad shows that most countries favour the mining technology approach, with the exception of Denmark where R and D work in this field is focused on deep well disposal. (orig./HP) [de

Working towards a universal container for category B waste

International Nuclear Information System (INIS)

Tallec, M.

2002-01-01

Long-lived, intermediate-level waste, known as category 8 waste, accounts for most long lived waste (> 90%), although it only accounts for a very small fraction of radiotoxicity (< 10%). It comes in a wide variety of forms. The first step to be taken is to classify it into a few families and define a standard management mode for each one. Research teams are therefore seeking to propose a range of universal containers for existing packages and waste still to be conditioned. (author)

Salt removal from tanks containing high-level radioactive waste

International Nuclear Information System (INIS)

Kiser, D.L.

1981-01-01

At the Savannah River Plant (SRP), there are 23 waste storage tanks containing high-level radioactive wastes that are to be retired. These tanks contain about 23 million liters of salt and about 10 million liters of sludge, that are to be relocated to new Type III, fully stress-relieved tanks with complete secondary containment. About 19 million liters of salt cake are to be dissolved. Steam jet circulators were originally proposed for the salt dissolution program. However, use of steam jet circulators raised the temperature of the tank contents and caused operating problems. These included increased corrosion risk and required long cooldown periods prior to transfer. Alternative dissolution concepts were investigated. Examination of mechanisms affecting salt dissolution showed that the ability of fresh water to contact the cake surface was the most significant factor influencing dissolution rate. Density driven and mechanical agitation techniques were developed on a bench scale and then were demonstrated in an actual waste tank. Actual waste tank demonstrations were in good agreement with bench-scale experiments at 1/85 scale. The density driven method utilizes simple equipment, but leaves a cake heel in the tank and is hindered by the presence of sludge or Zeolite in the salt cake. Mechanical agitation overcomes the problems found with both steam jet circulators and the density driven technique and is the best method for future waste tank salt removal

Valorization of Waste Obtained from Oil Extraction in Moringa Oleifera Seeds: Coagulation of Reactive Dyes in Textile Effluents.

Science.gov (United States)

Vilaseca, Mercè; López-Grimau, Víctor; Gutiérrez-Bouzán, Carmen

2014-09-12

Moringa oleifera seeds contain about 40% of highly valued oil due to its wide range of applications, from nutritional issues to cosmetics or biodiesel production. The extraction of Moringa oil generates a waste (65%-75% of seeds weight) which contains a water soluble protein able to be used either in drinking water clarification or wastewater treatment. In this paper, the waste of Moringa oleifera extraction was used as coagulant to remove five reactive dyes from synthetic textile effluents. This waste constitutes a natural coagulant which was demonstrated to be effective for the treatment of industrial reactive dyestuff effluents, characterized by alkaline pH, high NaCl content and hydrolyzed dyes. The coagulation yield increased at high NaCl concentration, whereas the pH did not show any significant effect on dye removal. Moringa oleifera showed better results for dye removal than the conventional treatment of coagulation-flocculation with FeCl₃ and polyelectrolyte. Treated water can be reused in new dyeing processes of cotton fabrics with high quality results.

Valorization of Waste Obtained from Oil Extraction in Moringa Oleifera Seeds: Coagulation of Reactive Dyes in Textile Effluents

Directory of Open Access Journals (Sweden)

Mercè Vilaseca

2014-09-01

Full Text Available Moringa oleifera seeds contain about 40% of highly valued oil due to its wide range of applications, from nutritional issues to cosmetics or biodiesel production. The extraction of Moringa oil generates a waste (65%–75% of seeds weight which contains a water soluble protein able to be used either in drinking water clarification or wastewater treatment. In this paper, the waste of Moringa oleifera extraction was used as coagulant to remove five reactive dyes from synthetic textile effluents. This waste constitutes a natural coagulant which was demonstrated to be effective for the treatment of industrial reactive dyestuff effluents, characterized by alkaline pH, high NaCl content and hydrolyzed dyes. The coagulation yield increased at high NaCl concentration, whereas the pH did not show any significant effect on dye removal. Moringa oleifera showed better results for dye removal than the conventional treatment of coagulation-flocculation with FeCl3 and polyelectrolyte. Treated water can be reused in new dyeing processes of cotton fabrics with high quality results.

Simultaneous treatment of SO2 containing stack gases and waste water

Science.gov (United States)

Poradek, J. C.; Collins, D. D. (Inventor)

1978-01-01

A process for simultaneously removing sulfur dioxide from stack gases and the like and purifying waste water such as derived from domestic sewage is described. A portion of the gas stream and a portion of the waste water, the latter containing dissolved iron and having an acidic pH, are contacted in a closed loop gas-liquid scrubbing zone to effect absorption of the sulfur dioxide into the waste water. A second portion of the gas stream and a second portion of the waste water are controlled in an open loop gas-liquid scrubbing zone. The second portion of the waste water contains a lesser amount of iron than the first portion of the waste water. Contacting in the openloop scrubbing zone is sufficient to acidify the waste water which is then treated to remove solids originally present.

A possible NaCl pathway in the bioregenerative human life support system

Science.gov (United States)

Polonskiy, V. I.; Gribovskaya, I. V.

One of the ways to involve NaCl in the mass exchange of the bioregenerative human life support system (BLSS) is to grow some vegetables and leafy greens that can accumulate sodium chloride at high concentrations in their edible biomass. Lettuce, celery cabbage, chard, dill and radish plants were grown hydroponically in Knop's nutrient solution. In the first series of experiments, at the end of the growth period the plants were grown on solutions containing 2-14 g/L of NaCl for 1-5 days. It was found that the amount of sodium in edible biomass of the plants increased with NaCl concentration in the solution and with the time plants were irrigated with that solution. The content of NaCl in the biomass of leaves and edible roots was considerable—up to 10% dry matter. At the same time, the amount of water in the leaves decreased and productivity of the treatment plants was 14-28% lower than that of the control ones, grown on Knop's solution. The treatment plants contained less than half of the amount of nitrates recorded in the control ones. Expert evaluation showed that the taste of the vegetables and leafy greens of the treatment group were not inferior to the taste of the control plants. In the second series of experiments, prior to being grown on the NaCl solution, the plants were irrigated with water for 2, 4 or 6 days. It was found that lower salt status of the plants was not favorable for increased salt accumulation in their biomass. If a human consumes 30 g salad vegetables and follows a low-sodium diet (3 g/d of table salt), it may be feasible to recycle NaCl in the BLSS using vegetables and leafy greens.

Cement-Polymer Composite Containers for Radioactive Wastes Disposal

International Nuclear Information System (INIS)

Ghattas, N.K.; Eskander, S.B.; Bayoumi, T.A.; Saleh, H.M.

2009-01-01

Improving cement-composite containers using polymer as organic additives was studied extensively. Both unsaturated styrenated polyester (SPE) and polymethyl methacrylate (PMMA) were used to fill the pores in cement containers that used for disposal of radioactive wastes. Two different techniques were adopted for the addition of organic polymers based on their viscosity. The low density PMMA was added using impregnation technique. On the other hand high density SPE was mixed with cement paste as a premix process. Predetermined weight of dried borate radioactive powder waste simulate was introduced into the Cement-polymer composite (CPC) container and then closed before subjecting it to leaching characterization. The effect of the organic polymers on the hydration of cement matrix and on the properties of the obtained CPC container has been studied using X-ray diffraction, IR-analysis, thermal effects and weight loss. Porosity, pore parameters and rate of release were also determined. The results obtained showed that for the candidate CPC container positive effect of polymer dominates and an improvement in the retardation rate of PMMA release radionuclides was observed

Characterization of drilling waste from shale gas exploration in Central and Eastern Poland.

Science.gov (United States)

Mikos-Szymańska, Marzena; Rusek, Piotr; Borowik, Krzysztof; Rolewicz, Maciej; Bogusz, Paulina; Gluzińska, Joanna

2018-05-28

The purpose of this research was to determine and evaluate the chemical properties of drilling waste from five well sites in Central and Eastern Poland. It was found that spent drilling fluids can contain high values of nickel and mercury (270 and 8.77 mg kg -1 , respectively) and can exceed the maximum permissible limits recommended by the EC regulations for safety of soils (75 mg kg -1 for nickel and 1.5 mg kg -1 for mercury). The heavy metal concentrations in the studied drill cuttings did not exceed the maximum permissible limits recommended by the EC regulation. Drilling wastes contain macroelements (e.g., calcium, magnesium, and potassium) as well as trace elements (e.g., copper, iron, zinc, and manganese) that are essential for the plant growth. It was stated that water extracts of drilling fluids and drill cuttings, according to anions presence, had not any specific constituents of concern based on FAO irrigation guidelines, the USEPA WQC, and toxicity values. X-ray diffraction analysis was used to understand the structure and texture of waste drilling fluid solids and drill cuttings. Analysis of the mineralogical character of drilling fluid solids revealed that they contained calcite, quartz, muscovite, sylvite, barite, dolomite, and orthoclase. Drill cuttings contained calcite quartz, muscovite, barite, dolomite, and barium chloride.

Evolution of thermoelectric performance for (Bi,Sb){sub 2}Te{sub 3} alloys from cutting waste powders to bulks with high figure of merit

Energy Technology Data Exchange (ETDEWEB)

Fan, Xi' an, E-mail: groupfxa@163.com [The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan 430081 (China); Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education, Wuhan University of Science and Technology, Wuhan 430081 (China); School of Materials and Metallurgy, Wuhan University of Science and Technology, 947 Heping Road, Qingshan District, Wuhan 430081 (China); Cai, Xin zhi, E-mail: xzcwust@163.com [The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan 430081 (China); Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education, Wuhan University of Science and Technology, Wuhan 430081 (China); School of Materials and Metallurgy, Wuhan University of Science and Technology, 947 Heping Road, Qingshan District, Wuhan 430081 (China); Han, Xue wu, E-mail: hanxuewu1990@163.com [The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan 430081 (China); Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education, Wuhan University of Science and Technology, Wuhan 430081 (China); School of Materials and Metallurgy, Wuhan University of Science and Technology, 947 Heping Road, Qingshan District, Wuhan 430081 (China); Zhang, Cheng cheng, E-mail: zcc516990418@live.com [The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan 430081 (China); Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education, Wuhan University of Science and Technology, Wuhan 430081 (China); School of Materials and Metallurgy, Wuhan University of Science and Technology, 947 Heping Road, Qingshan District, Wuhan 430081 (China); and others

2016-01-15

Bi{sub 2}Te{sub 3} based cutting waste powders from cutting wafers were firstly selected as raw materials to prepare p-type Bi{sub 2}Te{sub 3} based thermoelectric (TE) materials. Through washing, reducing, composition correction, smelting and resistance pressing sintering (RPS) process, p-type (Bi,Sb){sub 2}Te{sub 3} alloy bulks with different nominal stoichiometries were successfully obtained. The evolution of microstructure and TE performance for (Bi,Sb){sub 2}Te{sub 3} alloys were investigated in detail. All evidences confirmed that most of contaminants from line cutting process such as cutting fluid and oxides of Bi, Sb or Te could be removed by washing, reducing and smelting process used in this work. The carrier content and corresponding TE properties could be adjusted effectively by appropriate composition correction treatment. At lastly, a bulk with a nominal stoichiometry of Bi{sub 0.44}Sb{sub 1.56}Te{sub 3} was obtained and its' dimensionless figure of merit (ZT) was about 1.16 at 90 °C. The ZT values of Bi{sub 0.36}Sb{sub 1.64}Te{sub 3} and Bi{sub 0.4}Sb{sub 1.6}Te{sub 3} alloy bulks could also reach 0.98 and 1.08, respectively. Different from the conventional recycling technology such as hydrometallurgy extraction methods, the separation and extraction of beneficial elements such as Bi, Sb and Te did not need to be performed and the Bi{sub 2}Te{sub 3} based bulks with high TE properties could be directly obtained from the cutting waste powders. In addition, the recycling technology introduced here was green and more suitable for practical industrial application. It can improve material utilization and lower raw material costs of manufacturers. - Graphical abstract: Three kinds of typical morphologies for the fractographs: typical lamellar structure, agglomerated submicron-sized granules and dispersed cubic particles from the initial cutting waste powders. - Highlights: • Bi{sub 2}Te{sub 3} based wastes were directly selected as raw materials

41 CFR 50-204.72 - Safe practices for welding and cutting on containers which have held combustibles.

Science.gov (United States)

2010-07-01

... combustibles. Welding or cutting, or both, on containers which have held flammable or combustible solids, liquids, or gases, or have contained substances which may produce flammable vapors or gases will not be...

Concrete as secondary containment for interior wall embedded waste lines

International Nuclear Information System (INIS)

Porter, C.L.

1993-01-01

Throughout the Department of Energy (DOE) complex are numerous facilities that handle hazardous waste solutions. Secondary containment of tank systems and their ancillary piping is a major concern for existing facilities. The Idaho Division of Environmental Quality was petitioned in 1990 for an Equivalent Device determination regarding secondary containment of waste lines embedded in interior concrete walls. The petition was granted, however it expires in 1996. To address the secondary containment issue, additional studies were undertaken. One study verified the hypothesis that an interior wall pipe leak would follow the path of least resistance through the naturally occurring void found below a rigidly supported pipe and pass into an adjacent room where detection could occur, before any significant deterioration of the concrete takes place. Other tests demonstrated that with acidic waste solutions rebar and cold joints are not an accelerated path to the environment. The results from these latest studies confirm that the subject configuration meets all the requirements of secondary containment

Development of cutting and welding methods for thick-walled stainless steel support and containment structures for ITER

International Nuclear Information System (INIS)

Jones, L.; Maisonnier, D.; Goussain, J.; Johnson, G.; Petring, D.; Wernwag, L.

1998-01-01

In ITER the containment and support structures are made from 316L(N)-IG (ITER Grade) stainless steel plate, 40 to 70 mm thick. The structures are divided into twenty sectors which have to be welded together in situ. The three areas of work described in this paper are, CO 2 laser welding, plasma cutting and CO 2 laser cutting. CO 2 laser welding offers significant advantages due to its high speed and low distortion and the most powerful commercial laser in Europe has been used to investigate single pass welding of thick plates, with strong welds up to 35 mm thick being achieved in one pass. For cutting, the space available on the back-side to collect debris and protect fragile components from damage is limited to 30 mm. A static, water-cooled backside protection plate proved unable to contain the debris from plasma cutting so a reciprocating backside protection system with dry ceramic heat shield demonstrated a solution. A 10 kW CO 2 laser system for nitrogen-assisted laser cutting, provided successful results at 40 mm thickness. This technique shows considerable promise as significant reductions in through power and rate of debris production are expected compared with plasma cutting and thicker cuts appear feasible. The results presented herein represent significant technical advances and will be strong candidates for the mix of methods which will have to be used for the assembly and maintenance of the ITER machine. (authors)

Test plan for immobilization of salt-containing surrogate mixed wastes using polyester resins

International Nuclear Information System (INIS)

Biyani, R.K.; Douglas, J.C.; Hendrickson, D.W.

1997-01-01

Past operations at many Department of Energy (DOE) sites have resulted in the generation of several waste streams with high salt content. These wastes contain listed and characteristic hazardous constituents and are radioactive. The salts contained in the wastes are primarily chloride, sulfate, nitrate, metal oxides, and hydroxides. DOE has placed these types of wastes under the purview of the Mixed Waste Focus Area (MWFA). The MWFA has been tasked with developing and facilitating the implementation of technologies to treat these wastes in support of customer needs and requirements. The MWFA has developed a Technology Development Requirements Document (TDRD), which specifies performance requirements for technology owners and developers to use as a framework in developing effective waste treatment solutions. This project will demonstrate the use of polyester resins in encapsulating and solidifying DOE's mixed wastes containing salts, as an alternative to conventional and other emerging immobilization technologies

Test plan for immobilization of salt-containing surrogate mixed wastes using polyester resins

Energy Technology Data Exchange (ETDEWEB)

Biyani, R.K.; Douglas, J.C.; Hendrickson, D.W.

1997-07-07

Past operations at many Department of Energy (DOE) sites have resulted in the generation of several waste streams with high salt content. These wastes contain listed and characteristic hazardous constituents and are radioactive. The salts contained in the wastes are primarily chloride, sulfate, nitrate, metal oxides, and hydroxides. DOE has placed these types of wastes under the purview of the Mixed Waste Focus Area (MWFA). The MWFA has been tasked with developing and facilitating the implementation of technologies to treat these wastes in support of customer needs and requirements. The MWFA has developed a Technology Development Requirements Document (TDRD), which specifies performance requirements for technology owners and developers to use as a framework in developing effective waste treatment solutions. This project will demonstrate the use of polyester resins in encapsulating and solidifying DOE`s mixed wastes containing salts, as an alternative to conventional and other emerging immobilization technologies.

Corrosion susceptibility of steel drums containing cemented intermediate level nuclear wastes

Science.gov (United States)

Duffó, Gustavo S.; Farina, Silvia B.; Schulz, Fátima M.; Marotta, Francesca

2010-10-01

Cementation processes are used as immobilization techniques for low or intermediate level radioactive waste for economical and safety reasons and for being a simple operation. In particular, ion-exchange resins commonly used for purification of radioactive liquid waste from nuclear reactors are immobilized before being stored to improve the leach resistance of the waste matrix and to maintain mechanical stability. Combustible solid radioactive waste can be incinerated and the resulting ashes can also be immobilized before storage. The immobilized resins and ashes are then contained in steel drums that may undergo corrosion depending on the presence of certain contaminants. The work described in this paper was aimed at evaluating the corrosion susceptibility of steel drums in contact with cemented ion-exchange resins and incineration ashes containing different concentrations of aggressive species (mostly chloride and sulphate ions). A special type of specimen was designed to simulate the cemented waste in the drum. The evolution of the corrosion potential and the corrosion current density of the steel, as well as the electrical resistivity of the matrix were monitored over a time period of 1 year. The results show the deleterious effect of chloride on the expected lifespan of the waste containers.

Corrosion susceptibility of steel drums containing cemented intermediate level nuclear wastes

International Nuclear Information System (INIS)

Duffo, Gustavo S.; Farina, Silvia B.; Schulz, Fatima M.; Marotta, Francesca

2010-01-01

Cementation processes are used as immobilization techniques for low or intermediate level radioactive waste for economical and safety reasons and for being a simple operation. In particular, ion-exchange resins commonly used for purification of radioactive liquid waste from nuclear reactors are immobilized before being stored to improve the leach resistance of the waste matrix and to maintain mechanical stability. Combustible solid radioactive waste can be incinerated and the resulting ashes can also be immobilized before storage. The immobilized resins and ashes are then contained in steel drums that may undergo corrosion depending on the presence of certain contaminants. The work described in this paper was aimed at evaluating the corrosion susceptibility of steel drums in contact with cemented ion-exchange resins and incineration ashes containing different concentrations of aggressive species (mostly chloride and sulphate ions). A special type of specimen was designed to simulate the cemented waste in the drum. The evolution of the corrosion potential and the corrosion current density of the steel, as well as the electrical resistivity of the matrix were monitored over a time period of 1 year. The results show the deleterious effect of chloride on the expected lifespan of the waste containers.

Mercury recovery from mercury-containing wastes using a vacuum thermal desorption system.

Science.gov (United States)

Lee, Woo Rim; Eom, Yujin; Lee, Tai Gyu

2017-02-01

Mercury (Hg)-containing waste from various industrial facilities is commonly treated by incineration or stabilization/solidification and retained in a landfill at a managed site. However, when highly concentrated Hg waste is treated using these methods, Hg is released into the atmosphere and soil environment. To eliminate these risks, Hg recovery technology using thermal treatment has been developed and commercialized to recover Hg from Hg-containing waste for safe disposal. Therefore, we developed Hg recovery equipment to treat Hg-containing waste under a vacuum of 6.67kPa (abs) at 400°C and recover the Hg. In addition, the dust generated from the waste was separated by controlling the temperature of the dust filtration unit to 230°C. Additionally, water and Hg vapors were condensed in a condensation unit. The Hg removal rate after waste treatment was 96.75%, and the Hg recovery rate as elemental Hg was 75.23%. Copyright © 2016 Elsevier Ltd. All rights reserved.

Characterization of cement and bitumen waste forms containing simulated low-level waste incinerator ash

International Nuclear Information System (INIS)

Westsik, J.H. Jr.

1984-08-01

Incinerator ash from the combustion of general trash and ion exchange resins was immobilized in cement and bitumen. Tests were conducted on the resulting waste forms to provide a data base for the acceptability of actual low-level waste forms. The testing was done in accordance with the US Nuclear Regulatory Commission Technical Position on Waste Form. Bitumen had a measured compressive strength of 130 psi and a leachability index of 13 as measured with the ANS 16.1 leach test procedure. Cement demonstrated a compressive strength of 1400 psi and a leachability index of 7. Both waste forms easily exceed the minimum compressive strength of 50 psi and leachability index of 6 specified in the Technical Position. Irradiation to 10 8 Rad and exposure to 31 thermal cycles ranging from +60 0 ) to -30 0 C did not significantly impact these properties. Neither waste form supported bacterial or fungal growth as measured with ASTM G21 and G22 procedures. However, there is some indication of biodegradation due to co-metabolic processes. Concentration of organic complexants in leachates of the ash, cement and bitumen were too low to significantly affect the release of radionuclides from the waste forms. Neither bitumen nor cement containing incinerator ash caused any corrosion or degradation of potential container materials including steel, polyethylene and fiberglass. However, moist ash did cause corrosion of the steel

Computer simulation of radiation damage in NaCl using a kinetic rate reaction model

International Nuclear Information System (INIS)

Soppe, W.J.

1993-01-01

Sodium chloride and other alkali halides are known to be very susceptible to radiation damage in the halogen sublattice when exposed to ionizing radiation. The formation of radiation damage in NaCl has generated interest because of the relevance of this damage to the disposal of radioactive waste in rock salt formations. In order to estimate the long-term behaviour of a rock salt repository, an accurate theory describing the major processes of radiation damage in NaCl is required. The model presented in this paper is an extended version of the Jain-Lidiard model; its extensions comprise the effect of impurities and the colloid nucleation stage on the formation of radiation damage. The new model has been tested against various experimental data obtained from the literature and accounts for several well known aspects of radiation damage in alkali halides which were not covered by the original Jain-Lidiard model. The new model thus may be expected to provide more reliable predictions for the build-up of radiation damage in a rock salt nuclear waste repository. (Author)

Experimental determination of the H2O + 15 wt% NaCl and H2O + 25 wt% NaCl liquidi to 1.4 GPa

Science.gov (United States)

Valenti, P.; Schmidt, C.

2009-12-01

The binary H2O+NaCl is one of the most important model systems for chloridic fluids in many geologic environments such as the Earth’s crust, upper mantle, and subducting slabs, and is also applicable to extraterrestrial icy planetary bodies (e.g., Manning 2004, Zolensky et al., 1999). The knowledge on phase equilibria and PVTx properties of this system is still fragmentary at high pressures, e.g., very little has been reported on liquidi at compositions Daniel 2008). In this study, we investigated the liquidus of 15 and 25 wt% NaCl solutions at pressures up to 1.4 GPa. The experiments were performed using a hydrothermal diamond-anvil cell (Bassett et al. 1993) modified for Raman spectroscopy and accurate temperature measurements. A quartz chip, halite, and water were loaded into the sample chamber, which also contained a small trapped air bubble (10 vol%) when it was sealed. The actual salinity was then determined from measurement of the vapor-saturated liquidus temperature. The sample chamber was then compressed until the bubble disappeared. After freezing, phase transitions occurring with increasing temperature were observed optically, and the pressure was determined from the frequency shift of the 464 cm-1 Raman line of quartz (Schmidt and Ziemann 2000). The sample chamber was then compressed further, and the experiment was repeated at various bulk densities until a pressure of ~1.4 GPa was attained. At some conditions, Raman spectra were acquired for identification of the phase assemblage. The solution always crystallized to a single phase upon cooling above ~0.15 GPa at 25 wt% NaCl and above ~1 GPa at 15 wt% NaCl. Raman spectra in the OH stretching region indicate that this phase contains or is a NaCl hydrate other than hydrohalite, probably in solid solution with ice. Melting of this phase produced liquid and hydrohalite and/or ice VI. Ice VI was the last solid that dissolved upon heating, between 1100 MPa, 3 °C and 1370 MPa, 17 °C for 15 wt% NaCl and at

Laser cutting of various materials: Kerf width size analysis and life cycle assessment of cutting process

Science.gov (United States)

Yilbas, Bekir Sami; Shaukat, Mian Mobeen; Ashraf, Farhan

2017-08-01

Laser cutting of various materials including Ti-6Al-4V alloy, steel 304, Inconel 625, and alumina is carried out to assess the kerf width size variation along the cut section. The life cycle assessment is carried out to determine the environmental impact of the laser cutting in terms of the material waste during the cutting process. The kerf width size is formulated and predicted using the lump parameter analysis and it is measured from the experiments. The influence of laser output power and laser cutting speed on the kerf width size variation is analyzed using the analytical tools including scanning electron and optical microscopes. In the experiments, high pressure nitrogen assisting gas is used to prevent oxidation reactions in the cutting section. It is found that the kerf width size predicted from the lump parameter analysis agrees well with the experimental data. The kerf width size variation increases with increasing laser output power. However, this behavior reverses with increasing laser cutting speed. The life cycle assessment reveals that material selection for laser cutting is critical for the environmental protection point of view. Inconel 625 contributes the most to the environmental damages; however, recycling of the waste of the laser cutting reduces this contribution.

Discarding processing method for radioactive waste

International Nuclear Information System (INIS)

Komura, Shiro; Kato, Hiroaki; Hatakeyama, Takao; Oura, Masato.

1992-01-01

At first, in a discrimination step, extremely low level radioactive wastes are discriminated to metals and concretes and further, the metal wastes are discriminated to those having hollow portions and those not having hollow portions, and the concrete wastes are discriminated to those having block-like shape and those having other shapes respectively. Next, in a processing step, the metal wastes having hollow portions are applied with cutting, devoluming or packing treatment and block-like concrete wastes are applied with surface solidification treatment, and concrete wastes having other shapes are applied with crushing treatment respectively. Then, the extremely low level radioactive wastes contained in a container used exclusively for transportation are taken out, in a movable burying facility with diffusion inhibiter kept at a negative pressure as required, in a field for burying operation, and buried in a state that they are isolated from the outside. Accordingly, they can be buried safely and efficiently. (T.M.)

Greater-than-Class C low-level radioactive waste shipping package/container identification and requirements study. National Low-Level Waste Management Program

Energy Technology Data Exchange (ETDEWEB)

Tyacke, M.

1993-08-01

This report identifies a variety of shipping packages (also referred to as casks) and waste containers currently available or being developed that could be used for greater-than-Class C (GTCC) low-level waste (LLW). Since GTCC LLW varies greatly in size, shape, and activity levels, the casks and waste containers that could be used range in size from small, to accommodate a single sealed radiation source, to very large-capacity casks/canisters used to transport or dry-store highly radioactive spent fuel. In some cases, the waste containers may serve directly as shipping packages, while in other cases, the containers would need to be placed in a transport cask. For the purpose of this report, it is assumed that the generator is responsible for transporting the waste to a Department of Energy (DOE) storage, treatment, or disposal facility. Unless DOE establishes specific acceptance criteria, the receiving facility would need the capability to accept any of the casks and waste containers identified in this report. In identifying potential casks and waste containers, no consideration was given to their adequacy relative to handling, storage, treatment, and disposal. Those considerations must be addressed separately as the capabilities of the receiving facility and the handling requirements and operations are better understood.

Method and apparatus for disposing a radioactive waste container to submarine bottom

International Nuclear Information System (INIS)

Shibata, Kiyoshi; Yoshida, Shoichi.

1980-01-01

Purpose: To completely eliminate a danger occurred by the rolling of a hull in the ocean in a method and apparatus for disposing radioactive waste container to submarine bottom by independently handling the radioactive waste containers when loading the container in a compartment carried on a barge and sinking the containers together with the compartment to the submarine bottom at its disposing time. Method: Radioactive waste containers are carried into a compartment loaded on a barge floating completely, and the barge is then applied with external force thereto by a ship or the like and sailed to the marine disposal area. Then, water is filled in the ballast tank of the barge to submerge the barge, the compartment is floated and separated from the containers, and water is charged into the compartment to sink the compartment. (Aizawa, K.)

Utilization of crushed radioactive concrete for mortar to fill waste container void space

International Nuclear Information System (INIS)

Ishikura, Takeshi; Ohnishi, Kazuhiko; Oguri, Daiichiro; Ueki, Hiroyuki

2004-01-01

Minimizing the volume of radioactive waste generated during dismantling of nuclear power plants is a matter of great importance. In Japan waste forms buried in a shallow burial disposal facility as low level radioactive waste must be solidified by cement or other materials with adequate strength and must provide no harmful opening. The authors have developed an improved method to minimize radioactive waste volume by utilizing radioactive concrete for fine aggregate for mortars to fill void space in waste containers. Tests were performed with pre-placed concrete waste and with filling mortar using recycled fine aggregate produced from concrete. It was estimated that the improved method substantially increases the waste fill ratio in waste containers, thereby decreasing the total volume of disposal waste. (author)

Incineration of radioactive wastes containing only C-14 and H-3

International Nuclear Information System (INIS)

Garcia, Corazon M.

1992-01-01

C-14 and H-3 arc popularly used in chemical and biological research institutions in the Philippines. Most of the solid radioactive wastes generated by these institutions consist of combustible materials such as paper and accumulated environmental samples. Liquid wastes usually contain organic substances. The method proposed for managing C-14 and H-3 wastes is incineration which is expected to provide an acceptable means of disposal for C-14 and H-3 and their hazardous organic constituent. In the incineration process) the radioactively contaminated waste will be mixed with non-radioactive combustible wastes to lower the activity concentration and to improve the efficiency of combustion which will be carried out in a locally fabricated drum incinerator. The calculations presented determines the concentration limit for the incinerable wastes and the restriction on specific activity of the particles of the incinerable wastes containing C-14 or H-3 on the basis of the accepted air concentration and on the annual dose limit for an average radiation worker in the country. In the calculations for C-14, considerations were taken on the exposure received from the deposition of radioactive particles in the lungs containing unoxidized carbon. Calculations for H-3, however, is based on the assumption that the concentration of the radionuclide in the body water is the same as that in the environment. (author)

Treatment of cyanide-contained Waste Water

International Nuclear Information System (INIS)

Scheglov, M.Y.

1999-01-01

This work contains results of theoretical and experimental investigations of possibility to apply industrial ionites of different kinds for recovering complex cyanide of some d-elements (Cu, Zn, an dso on) and free CN-ions with purpose to develop technology and unit for plating plant waste water treatment. Finally, on basis of experimental data about equilibrium kinetic and dynamic characteristic of the sorption in model solutions, strong base anionite in CN- and OH-forms was chosen. This anionite has the best values of operational sorption uptake. Recommendations of using the anionite have been developed for real cyanide-contained wastewater treatment

Heat transfer effects in vertically emplaced high level nuclear waste container

International Nuclear Information System (INIS)

Moujaes, S.F.; Lei, Y.M.

1994-01-01

Modeling free convection heat transfer in a cylindrical annular enclosure is still an active area of research and an important problem to be addressed in the high level nuclear waste repository. For the vertically emplaced waste container, the air gap which is between the container shell and the rock borehole, have an important role of dissipating heat to surrounding rock. These waste containers are vertically emplaced in the borehole 300 meters just below ground, and in a horizontal grid of 30 x 8 meters apart. The borehole will be capped after the container emplacement. The expected initial heat generated is between 3-4.74 kW per container depending on the type of waste. The goal of this study is to use a computer simulation model to find the borehole wall, air-gap and the container outer wall temperature distributions. The borehole wall temperature history has been found in the previous study, and was estimated to reach a maximum temperature of about 218 degrees C after 18 years from the emplacement. The temperature history of the rock surface is then used for the air-gap simulation. The problem includes convection and radiation heat transfer in a vertical enclosure. This paper will present the results of the convection in the air-gap over one thousand years after the containers' emplacement. During this long simulation period it was also observed that a multi-cellular air flow pattern can be generated in the air gap

Preliminary assessment of the controlled release of radionuclides from waste packages containing borosilicate waste glass

International Nuclear Information System (INIS)

Strachan, D.M.; McGrail, B.P.; Apted, M.J.; Engle, D.W.; Eslinger, P.W.

1990-06-01

The purpose of this report is to provide a preliminary assessment of the release-rate for an engineered barriers subsystem (EBS) containing waste packages of defense high-level waste borosilicate glass at geochemical and hydrological conditions similar to the those at Yucca Mountain. The relationship between the proposed Waste Acceptance Preliminary Specifications (WAPS) test of glass- dissolution rate and compliance with the NRC's release-rate criterion is also evaluated. Calculations are reported for three hierarchical levels: EBS analysis, waste-package analysis, and waste-glass analysis. The following conclusions identify those factors that most acutely affect the magnitude of, or uncertainty in, release-rate performance

Treatment of low and intermediate aqueous waste containing Cs-137 by chemical precipitation

International Nuclear Information System (INIS)

Valdezco, E.M.; Marcelo, E.A.; Alamares, A.L.; Junio, J.B.; Dela Cruz, J.M.

1996-01-01

The use of radioactive materials in various applications has been increasing since its introduction in the early sixties. The Philippine Nuclear Research Institute has established a centralized facility for treating radioactive wastes i.e. aqueous wastes with assistance from the International Atomic Energy Agency - Technical Cooperation Programme. Liquid wastes containing Cs-137 are generated from aqueous wastes containing Cs-137 by nickel ferrocyanide precipitation will be presented. The aim of this study is to investigate the efficiency treatment in removing Cs-137 from an aqueous effluent. Actual aqueous wastes known to contain Cs-137 were used in the experiments. Low cost and simple nickel ferrocyanide precipitation method with the aid of a flocculant has been selected for the separation of Cs-137 from low and intermediate aqueous waste. By varying the chemical dosage added into the aqueous waste, different decontamination factors were obtained. Hence, the optimum dosage of the chemicals that give the highest decontamination factor can be determined. (author)

Feasibility study using hypothesis testing to demonstrate containment of radionuclides within waste packages

International Nuclear Information System (INIS)

Thomas, R.E.

1986-04-01

The purpose of this report is to apply methods of statistical hypothesis testing to demonstrate the performance of containers of radioactive waste. The approach involves modeling the failure times of waste containers using Weibull distributions, making strong assumptions about the parameters. A specific objective is to apply methods of statistical hypothesis testing to determine the number of container tests that must be performed in order to control the probability of arriving at the wrong conclusions. An algorithm to determine the required number of containers to be tested with the acceptable number of failures is derived as a function of the distribution parameters, stated probabilities, and the desired waste containment life. Using a set of reference values for the input parameters, sample sizes of containers to be tested are calculated for demonstration purposes. These sample sizes are found to be excessively large, indicating that this hypothesis-testing framework does not provide a feasible approach for demonstrating satisfactory performance of waste packages for exceptionally long time periods

Enviro-geotechnical considerations in waste containment system design and analysis

International Nuclear Information System (INIS)

Fang, H.Y.; Daniels, J.L.; Inyang, H.I.

1997-01-01

The effectiveness of waste control facilities hinges on careful evaluation of the overall planning, analysis and design of the entire system prior to construction. At present, most work is focused on the waste controlling system itself, with little attention given to the local environmental factors surrounding the facility sites. Containment materials including geomembranes, geotextiles and clay amended soils have received intense scrutiny. This paper, however, focuses on three relatively important issues relating to the characterization of the surrounding geomedia. Leakage through naturally occurring low-permeability soil layers, shrinkages swelling, cracking and effects of dynamic loads on system components are often responsible for a waste containment breach. In this paper, these mechanisms and their synergistic effects are explained in terms of the particle energy field theory. It is hoped that this additional information may assist the designer to be aware or take precaution to design safer future waste control facilities

LLNL/YMP Waste Container Fabrication and Closure Project

International Nuclear Information System (INIS)

1990-10-01

The Department of Energy's Office of Civilian Radioactive Waste Management (OCRWM) Program is studying Yucca Mountain, Nevada as a suitable site for the first US high-level nuclear waste repository. Lawrence Livermore National Laboratory (LLNL) has the responsibility for designing and developing the waste package for the permanent storage of high-level nuclear waste. This report is a summary of the technical activities for the LLNL/YMP Nuclear Waste Disposal Container Fabrication and Closure Development Project. Candidate welding closure processes were identified in the Phase 1 report. This report discusses Phase 2. Phase 2 of this effort involved laboratory studies to determine the optimum fabrication and closure processes. Because of budget limitations, LLNL narrowed the materials for evaluation in Phase 2 from the original six to four: Alloy 825, CDA 715, CDA 102 (or CDA 122) and CDA 952. Phase 2 studies focused on evaluation of candidate material in conjunction with fabrication and closure processes

The market-incentive recycling system for waste packaging containers in Taiwan

International Nuclear Information System (INIS)

Bor Yunchang, Jeffrey; Chien, Y.-L.; Hsu, Esher

2004-01-01

This paper presents a new market-incentive (MI) system to recycle waste-packaging containers in Taiwan. Since most used packaging containers have no or insufficient market value, the government imposes a combined product charge and subsidy policy to provide enough economic incentive for recycling various kinds of packaging containers, such as iron, aluminum, paper, glass and plastic. Empirical results show that the new MI approach has stimulated and established the recycling market for waste-packaging containers. The new recycling system has provided 18,356 employment opportunities and generated NT$ 6.97 billion in real-production value and NT$ 3.18 billion in real GDP during the 1998 survey year. Cost-effectiveness analysis constitutes the theoretical foundation of the new scheme, whereas data used to compute empirical product charge are from two sources: marketing surveys of internal conventional costs of solid-waste collection, disposal and recycling in Taiwan, and benefit transfer of external environmental costs in the United States. The new recycling policy designed by the authors provides a reasonable solution for solid-waste management in a country with limited land resources such as Taiwan

Evaluation of doses during the handling and transport of radioactive wastes containers

International Nuclear Information System (INIS)

Kubik, I.; Kusovska, Z.; Hanusik, V.; Mrskova, A.; Kapisovsky, V.

2000-01-01

Radioactive waste products from the nuclear power plants (NPPs) must be isolated from contact with people for very long period of time. Low and intermediate-level waste will be disposed of in Slovakia in specially licensed Regional disposal facility which is located near the NPP Mochovce site. Radioactive waste accumulated in the Jaslovsk. Bohunice site, during the decommissioning process of the NPP A-1 and arising from the NPP V-1 and NPP V-2 operation, will be processed and shipped in standard concrete containers to the Mochovce Regional disposal facility. The treatment centre was build at the NPP Jaslovsk? Bohunice site which is in the trial operation now. It is supposed that radioactive waste containers will be transported by train from the treatment centre Jaslovsk? Bohunice to the site of Radioactive Waste Repository at Mochovce and by truck in the area of repository. To estimate the occupational radiation exposure during the transport the calculations of dose rates from the containers are necessary. The national regulations allow low level of radiation to emanate from the casks and containers. The maximum permissible volume radioactivity of wastes inside the container is limited in such a way that irradiation level should not exceed 2 mGy/h for the contact irradiation level and 0,1 mGy/h at 2-meter distance. MicroShield code was used to analyse shielding and assessing exposure from gamma radiation of containers to people. A radioactive source was conservatively modelled by homogenous mixture of radionuclides with concrete. Standard rectangular volume source and shield geometry is used in model calculations. The activities of the personnel during the transport and storage of containers are analysed and results of the evaluation of external dose rates and effective doses are described. (author)

PRODUCTION OF NEW BIOMASS/WASTE-CONTAINING SOLID FUELS

Energy Technology Data Exchange (ETDEWEB)

David J. Akers; Glenn A. Shirey; Zalman Zitron; Charles Q. Maney

2001-04-20

CQ Inc. and its team members (ALSTOM Power Inc., Bliss Industries, McFadden Machine Company, and industry advisors from coal-burning utilities, equipment manufacturers, and the pellet fuels industry) addressed the objectives of the Department of Energy and industry to produce economical, new solid fuels from coal, biomass, and waste materials that reduce emissions from coal-fired boilers. This project builds on the team's commercial experience in composite fuels for energy production. The electric utility industry is interested in the use of biomass and wastes as fuel to reduce both emissions and fuel costs. In addition to these benefits, utilities also recognize the business advantage of consuming the waste byproducts of customers both to retain customers and to improve the public image of the industry. Unfortunately, biomass and waste byproducts can be troublesome fuels because of low bulk density, high moisture content, variable composition, handling and feeding problems, and inadequate information about combustion and emissions characteristics. Current methods of co-firing biomass and wastes either use a separate fuel receiving, storage, and boiler feed system, or mass burn the biomass by simply mixing it with coal on the storage pile. For biomass or biomass-containing composite fuels to be extensively used in the U.S., especially in the steam market, a lower cost method of producing these fuels must be developed that includes both moisture reduction and pelletization or agglomeration for necessary fuel density and ease of handling. Further, this method of fuel production must be applicable to a variety of combinations of biomass, wastes, and coal; economically competitive with current fuels; and provide environmental benefits compared with coal. Notable accomplishments from the work performed in Phase I of this project include the development of three standard fuel formulations from mixtures of coal fines, biomass, and waste materials that can be used in

Corrosion of radioactive waste containers, case of a container made of low allow steel

International Nuclear Information System (INIS)

Bataillon, C.; Musy, C.; Roy, M.

2001-01-01

The following topics were dealt with: radioactive waste concept ANDRA, low alloy steel (XC38) container corrosion under representative storage conditions, corrosion rate and passivation effects, micrographic investigations

Corrosion kinetics of alloy Ni-22Cr-13Mo-3W as structural material in high level nuclear waste containers

International Nuclear Information System (INIS)

Rodriguez, Martin A.

2004-01-01

Alloy Ni-22Cr-13Mo-3W (also known as C-22) is one of the candidates to fabricate high level nuclear waste containers. These containers are designed to maintain isolation of the waste for a minimum of 10,000 years. In this period, the material must be resistant to corrosion. If the containers were in contact with water, it is assumed that alloy C-22 may undergo three different corrosion mechanisms: general corrosion, localized corrosion and stress corrosion cracking. This thesis discusses only the first two types of degradation. Electrochemical techniques such as amperometry, potentiometry, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) and non-electrochemical techniques such as microscopic observation, X-ray fluorescence (XRF) and X-ray photoelectron spectroscopy (XPS) were applied to study the corrosion behavior of alloy C-22 in 1 M NaCl, 25 C degrees saturated NaF (approximately 1 M) and 0,5 M NaCl + 0,5 M NaF solutions. Effects of temperature, pH and alloy thermal aging were analyzed. The corrosion rates obtained at 90 C degrees were low ranging from 0.04 μm/year to 0.48 μm /year. They increased with temperature and decreased with solution pH. Most of the impedance measurements showed a simply capacitive behavior. A second high-frequency time constant was detected in some cases. It was attributed to the formation of a nickel oxide and/or hydroxide at potentials near the reversible potential for this reaction. The active/passive transition detected in some potentiodynamic polarization curves was attributed to the same process. The corrosion potential showed an important increase after 24 hours of immersion. This increase in the corrosion potential was associated with an improvement of the passive film. The corrosion potential was always lower than the re-passivation potential for the corresponding media. The trans passive behavior of alloy C-22 was mainly influenced by temperature and solution chemistry. A clear trans passive peak

DNA scanning mechanism of T4 endonuclease V. Effect of NaCl concentration on processive nicking activity

International Nuclear Information System (INIS)

Gruskin, E.A.; Lloyd, R.S.

1986-01-01

T4 endonuclease V is a pyrimidine dimer-specific endonuclease which generates incisions in DNA at the sites of pyrimidine dimers by a processive reaction mechanism. A model is presented in which the degree of processivity is directly related to the efficacy of the one-dimensional diffusion of endonuclease V on DNA by which the enzyme locates pyrimidine dimers. The modulation of the processive nicking activity of T4 endonuclease V on superhelical covalently closed circular DNA (form I) which contains pyrimidine dimers has been investigated as a function of the ionic strength of the reaction. Agarose gel electrophoresis was used to separate the three topological forms of the DNA which were generated in time course reactions of endonuclease V with dimer-containing form I DNA in the absence of NaCl, and in 25, 50, and 100 mM NaCl. The degree of processivity was evaluated in terms of the mass fraction of form III (linear) DNA which was produced as a function of the fraction of form I DNA remaining. Processivity is maximal in the absence of NaCl and decreases as the NaCl concentration is increased. At 100 mM NaCl, processivity is abolished and endonuclease V generates incisions in DNA at the site of dimers by a distributive reaction mechanism. The change from the distributive to a processive reaction mechanism occurs at NaCl concentrations slightly below 50 mM. The high degree of processivity which is observed in the absence of NaCl is reversible to the distributive mechanism, as demonstrated by experiments in which the NaCl concentration was increased during the time course reaction. In addition, unirradiated DNA inhibited the incision of irradiated DNA only at NaCl concentrations at which processivity was observed

POLYMER COMPOSITES MODIFIED BY WASTE MATERIALS CONTAINING WOOD FIBRES

Directory of Open Access Journals (Sweden)

Bernardeta Dębska

2016-11-01

Full Text Available In recent years, the idea of sustainable development has become one of the most important require-ments of civilization. Development of sustainable construction involves the need for the introduction of innovative technologies and solutions that will combine beneficial economic effects with taking care of the health and comfort of users, reducing the negative impact of the materials on the environment. Composites obtained from the use of waste materials are part of these assumptions. These include modified epoxy mortar containing waste wood fibres, described in this article. The modification consists in the substitution of sand by crushed waste boards, previously used as underlays for panels, in quantities of 0%, 10%, 20%, 35% and 50% by weight, respectively. Composites containing up to 20% of the modifier which were characterized by low water absorption, and good mechanical properties, also retained them after the process of cyclic freezing and thawing.

Effect of NaCl on seed germination in some Centaurium Hill. Species (Gentianaceae

Directory of Open Access Journals (Sweden)

Živković S.

2007-01-01

Full Text Available The influence of high NaCl concentrations on seed germination in both light and darkness was examined in the species Centaurium pulchellum, C. erythraea, C. littorale, C. spicatum, and C. tenuiflorum. Salt tolerance was found to depend on the life history of the seeds. To be specific, seeds of all five species failed to complete germination when exposed to continuous white light if kept all the time in the presence of 100-200 mM and greater NaCl concentrations. However, when after two weeks NaCl was rinsed from the seeds and the seeds were left in distilled water under white light for an additional two weeks, all species completed germination to a certain extent. The percent of germination not only depended on NaCl concentration in the prior medium, but was also species specific. Thus, seeds of C. pulchellum, C. erythraea, and C. littorale completed germination well almost irrespective of the salt concentration previously experienced. On the other hand, seeds of C. tenuiflorum completed germination poorly if NaCl concentrations in the prior media were greater than 200 mM. When seeds after washing were transferred to darkness for an additional 14 days, they failed to complete germination if previously imbibed on media containing NaCl concentrations greater than 400 mM. However, the seeds of all species, even if previously imbibed at 800 mM NaCl, could be induced to complete germination in darkness by 1 mM gibberellic acid. .

Characterisation of concrete containers for radioactive waste in the engineering tranches system at the Yugoslav R.A waste storing center

International Nuclear Information System (INIS)

Plecas, I.; Peric, A.; Drljaca, J.; Kostadinovic, A.

1987-10-01

Low and intermediate level radioactive waste represents 90% of total R.A. waste. It is conditioned into special concrete containers. Since these concrete containers are to protect safely the radioactive waste for 300 years, the selection of materials and precise control of their physical and mechanical properties is very important. In this paper results obtained with some concrete compositions are described. (author)

ERG review of waste package container materials selection and corrosion

International Nuclear Information System (INIS)

Moak, D.P.; Perrin, J.S.

1986-07-01

The Engineering Review Group (ERG) was established by the Office of Nuclear Waste Isolation (ONWI) to help evaluate engineering-related issues in the US Department of Energy's nuclear waste repository program. The October 1984 meeting of the ERG reviewed the waste package container materials selection and corrosion. This report documents the ERG's comments and recommendations on these subjects and the ONWI response to the specific points raised by the ERG

Method of processing liquid wastes containing radioactive materials

International Nuclear Information System (INIS)

Matsumoto, Kaname; Shirai, Takamori; Nemoto, Kuniyoshi; Yoshikawa, Jun; Matsuda, Takeshi.

1983-01-01

Purpose: To reduce the number of solidification products by removing, particularly, Co-60 that is difficult to remove in a radioactive liquid wastes containing a water-soluble chelating agent, by adsorbing Co-60 to a specific chelating agent. Method: Liquid wastes containing radioactive cobalt and water-soluble chelating agent are passed through the layer of less water-soluble chelating agent that forms a complex compound with cobalt in an acidic pH region. Thus, the chelating compound of radioactive cobalt (particularly Co-60) is eliminated by adsorbing the same on a specific chelating agent layer. The chelating agent having Co-60 adsorbed thereon is discarded as it is through the cement- or asphalt-solidification process, whereby the number of solidification products to be generated can significantly be suppressed. (Moriyama, K.)

Radiolytic gas production from concrete containing Savannah River Plant waste

International Nuclear Information System (INIS)

Bibler, N.E.

1978-01-01

To determine the extent of gas production from radiolysis of concrete containing radioactive Savannah River Plant waste, samples of concrete and simulated waste were irradiated by 60 Co gamma rays and 244 Cm alpha particles. Gamma radiolysis simulated radiolysis by beta particles from fission products in the waste. Alpha radiolysis indicated the effect of alpha particles from transuranic isotopes in the waste. With gamma radiolysis, hydrogen was the only significant product; hydrogen reached a steady-state pressure that increased with increasing radiation intensity. Hydrogen was produced faster, and a higher steady-state pressure resulted when an organic set retarder was present. Oxygen that was sealed with the wastes was depleted. Gamma radiolysis also produced nitrous oxide gas when nitrate or nitrite was present in the concrete. With alpha radiolysis, hydrogen and oxygen were produced. Hydrogen did not reach a steady-state pressure at 137 Cs and 90 Sr), hydrogen will reach a steady-state pressure of 8 to 28 psi, and oxygen will be partially consumed. These predictions were confirmed by measurement of gas produced over a short time in a container of concrete and actual SRP waste. The tests with simulated waste also indicated that nitrous oxide may form, but because of the low nitrate or nitrite content of the waste, the maximum pressure of nitrous oxide after 300 years will be 238 Pu and 239 Pu will predominate; the hydrogen and oxygen pressures will increase to >200 psi

Results from simulated contact-handled transuranic waste experiments at the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Molecke, M.A.; Sorensen, N.R.; Krumhansl, J.L.

1993-01-01

We conducted in situ experiments with nonradioactive, contact-handled transuranic (CH TRU) waste drums at the Waste Isolation Pilot Plant (WIPP) facility for about four years. We performed these tests in two rooms in rock salt, at WIPP, with drums surrounded by crushed salt or 70 wt % salt/30 wt % bentonite clay backfills, or partially submerged in a NaCl brine pool. Air and brine temperatures were maintained at ∼40C. These full-scale (210-L drum) experiments provided in situ data on: backfill material moisture-sorption and physical properties in the presence of brine; waste container corrosion adequacy; and, migration of chemical tracers (nonradioactive actinide and fission product simulants) in the near-field vicinity, all as a function of time. Individual drums, backfill, and brine samples were removed periodically for laboratory evaluations. Waste container testing in the presence of brine and brine-moistened backfill materials served as a severe overtest of long-term conditions that could be anticipated in an actual salt waste repository. We also obtained relevant operational-test emplacement and retrieval experience. All test results are intended to support both the acceptance of actual TRU wastes at the WIPP and performance assessment data needs. We provide an overview and technical data summary focusing on the WIPP CH TRU envirorunental overtests involving 174 waste drums in the presence of backfill materials and the brine pool, with posttest laboratory materials analyses of backfill sorbed-moisture content, CH TRU drum corrosion, tracer migration, and associated test observations

A review of the Hanford Site soil corrosion applicable to solid waste containers

International Nuclear Information System (INIS)

Divine, J.R.

1991-05-01

The first phase of the assessment of the soil corrosion in the solid waste burial grounds of the 200 Areas at the Hanford Site is completed with this review of both existing information developed at the site and relevant offsite information. Detailed soil corrosion data are needed for several reasons: (1) the possibility of predicting the damage to the containers of the retrievable stored transuranic waste that are under soil cover, (2) the feasibility of forecasting the state of waste containers being retrieved in remedial investigation/feasibility studies, (3) the capability of predicting subsidence of the soil over the waste containers, and (4) the capability of forecasting when stored lead shielding or hazardous chemicals might be exposed to the environment. Because corrosion in soils is dependent on the soil type, site-specific data are required even though offsite data can provide guidance on the type and the approximate extent of corrosion to expect. These data permit rough estimations of the corrosion rates of a variety of materials -- including carbon steels, cast irons, stainless steels, and lead -- in the Hanford Site soils. This report attempts to compile these data to facilitate current estimates of waste container longevity. However, because of the lack of well-documented, site-specific data, it is difficult to provide a definite life expectancy for waste containers and other structures. Consequently, additional data are essential for reliable container life estimates. 36 refs., 10 figs., 7 tabs

Assessing reliability and useful life of containers for disposal of irradiated fuel waste

International Nuclear Information System (INIS)

Doubt, G.

1984-06-01

Metal containers for fuel waste isolation are to be designed to last at least 500 years to provide a redundant barrier during the decay period of the high activity components of the waste. To meet the long-life requirement, containers must have a very low failure rate during the design mission, a low incidence of 'juvenile failures' due to undetected defects, and resistance to progressive deterioration from environmental processes. This paper summarizes studies to determine: (1) precedent for low failure rates and relevance to container longevity; (b) the likelihood of initial defects perforating the container before or shortly after emplacement, and estimates of material defect distribution; (c) the utility of reliability analysis techniques for estimating reliability and life of fuel waste containers; (d) other approaches to estimating container longevity and failure versus time distribution

Buried waste containment system materials. Final Report

International Nuclear Information System (INIS)

Weidner, J.R.; Shaw, P.G.

1997-10-01

This report describes the results of a test program to validate the application of a latex-modified cement formulation for use with the Buried Waste Containment System (BWCS) process during a proof of principle (POP) demonstration. The test program included three objectives. One objective was to validate the barrier material mix formulation to be used with the BWCS equipment. A basic mix formula for initial trials was supplied by the cement and latex vendors. The suitability of the material for BWCS application was verified by laboratory testing at the Idaho National Engineering and Environmental Laboratory (INEEL). A second objective was to determine if the POP BWCS material emplacement process adversely affected the barrier material properties. This objective was met by measuring and comparing properties of material prepared in the INEEL Materials Testing Laboratory (MTL) with identical properties of material produced by the BWCS field tests. These measurements included hydraulic conductivity to determine if the material met the US Environmental Protection Agency (EPA) requirements for barriers used for hazardous waste sites, petrographic analysis to allow an assessment of barrier material separation and segregation during emplacement, and a set of mechanical property tests typical of concrete characterization. The third objective was to measure the hydraulic properties of barrier material containing a stop-start joint to determine if such a feature would meet the EPA requirements for hazardous waste site barriers

Metal Cutting for Large Component Removal

International Nuclear Information System (INIS)

Hulick, Robert M.

2008-01-01

Decommissioning of commercial nuclear power plants presents technological challenges. One major challenge is the removal of large components mainly consisting of the reactor vessel, steam generators and pressurizer. In order to remove and package these large components nozzles must be cut from the reactor vessel to precise tolerances. In some cases steam generators must be segmented for size and weight reduction. One innovative technology that has been used successfully at several commercial nuclear plant decommissioning is diamond wire sawing. Diamond wire sawing is performed by rotating a cable with diamond segments attached using a flywheel approximately 24 inches in diameter driven remotely by a hydraulic pump. Tension is provided using a gear rack drive which also takes up the slack in the wire. The wire is guided through the use of pulleys keeps the wire in a precise location. The diamond wire consists of 1/4 inch aircraft cable with diamond beads strung over the cable separated by springs and brass crimps. Standard wire contains 40 diamond beads per meter and can be made to any length. Cooling the wire and controlling the spread of contamination presents significant challenges. Under normal circumstances the wire is cooled and the cutting kerf cleaned by using water. In some cases of reactor nozzle cuts the use of water is prohibited because it cannot be controlled. This challenge was solved by using liquid Carbon Dioxide as the cooling agent. The liquid CO 2 is passed through a special nozzle which atomizes the liquid into snowflakes which is introduced under pressure to the wire. The snowflakes attach to the wire keeping it cool and to the metal shavings. As the CO 2 and metal shavings are released from the wire due to its fast rotation, the snowflakes evaporate leaving only the fine metal shavings as waste. Secondary waste produced is simply the small volume of fine metal shavings removed from the cut surface. Diamond wire sawing using CO 2 cooling has

Selectivity of NF membrane for treatment of liquid waste containing uranium

International Nuclear Information System (INIS)

Oliveira, Elizabeth E.M.; Barbosa, Celina C.R.; Afonso, Julio C.

2013-01-01

The performance of two nanofiltration membranes were investigated for treatment of liquid waste containing uranium through two conditions permeation: permeation test and concentration test of the waste. In the permeation test solution permeated returned to the feed tank after collected samples each 3 hours. In the test of concentration the permeated was collected continuously until 90% reduction of the feed volume. The liquid waste ('carbonated water') was obtained during conversion of UF 6 to UO 2 in the cycle of nuclear fuel. This waste contains uranium concentration on average 7.0 mg L -1 , and not be eliminated to the environmental. The waste was permeated using a cross-flow membrane cell in the pressure of the 1.5 MPa. The selectivity of the membranes for separation of uranium was between 83% and 90% for both tests. In the concentration tests the waste was concentrated around for 5 times. The surface layer of the membranes was evaluated before and after the tests by infrared spectroscopy (ATR-FTIR), field emission microscopy (FESEM) and atomic force spectroscopy (AFM). The membrane separation process is a technique feasible to and very satisfactory for treatment the liquid waste. (author)

Migration rates of brine inclusions in single crystals of NaCl

International Nuclear Information System (INIS)

Chou, I.M.

1982-01-01

Rock-salt deposits have been considered as a possible medium for the permanent storage of high-level radioactive wastes and spent fuel. Brine inclusions present in natural salt can migrate toward the waste if the temperature and the temperature gradients in the vicinity of the radioactive waste are large enough. This migration is due to the dissolution of salt at the hot side of the salt-brine interface, ion diffusion through the brine droplet, and the precipitation of salt at the cold side of the salt brine interface. In order to quantify the problem, the migration rate of these brine inclusions must be estimated under various repository conditions. This paper estimates migration rates for all-liquid brine inclusions in single crystals of NaCl by utilizing recent data for brines and the model of Anthony and Cline [T.R. Anthony and H.E. Cline, J. Appl. Phys., 42, pp. 3380-387 (1971)]. The predictions are compared with experimentally measured migration rates. 4 figures, 6 tables

Gas flow in and out of a nuclear waste container

International Nuclear Information System (INIS)

Zwahlen, E.D.; Pigford, T.H.; Chambre, P.L.; Lee, W.W.L.

1989-05-01

We analyze the flow of gases out of and into a high-level-waste container in the unsaturated tuff of Yucca Mountain. Containers are expected to fail eventually by localized cracks and penetrations. Even though the penetrations may be small, argon gas initially in the hot container can leak out. As the waste package cools, the pressure inside the container can become less than atmospheric, and air can leak in. 14 C released from the hot fuel-cladding surface can leak out of penetrations, and air inleakage can mobilize additional 14 C and other volatile radioactive species as it oxidizes the fuel cladding and the spent fuel. In an earlier paper we studied the gas flow through container penetrations occurring at the time of emplacement. Here we analyze the flow of gas for various penetration sizes occurring at 300 years. 3 refs., 2 figs

Characteristics of solidified products containing radioactive molten salt waste.

Science.gov (United States)

Park, Hwan-Seo; Kim, In-Tae; Cho, Yong-Zun; Eun, Hee-Chul; Kim, Joon-Hyung

2007-11-01

The molten salt waste from a pyroprocess to recover uranium and transuranic elements is one of the problematic radioactive wastes to be solidified into a durable wasteform for its final disposal. By using a novel method, named as the GRSS (gel-route stabilization/solidification) method, a molten salt waste was treated to produce a unique wasteform. A borosilicate glass as a chemical binder dissolves the silicate compounds in the gel products to produce one amorphous phase while most of the phosphates are encapsulated by the vitrified phase. Also, Cs in the gel product is preferentially situated in the silicate phase, and it is vitrified into a glassy phase after a heat treatment. The Sr-containing phase is mainly phosphate compounds and encapsulated by the glassy phase. These phenomena could be identified by the static and dynamic leaching test that revealed a high leach resistance of radionuclides. The leach rates were about 10(-3) - 10(-2) g/m2 x day for Cs and 10(-4) - 10(-3) g/m2 x day for Sr, and the leached fractions of them were predicted to be 0.89% and 0.39% at 900 days, respectively. This paper describes the characteristics of a unique wasteform containing a molten salt waste and provides important information on a newly developed immobilization technology for salt wastes, the GRSS method.

Test procedures for polyester immobilized salt-containing surrogate mixed wastes

International Nuclear Information System (INIS)

Biyani, R.K.; Hendrickson, D.W.

1997-01-01

These test procedures are written to meet the procedural needs of the Test Plan for immobilization of salt containing surrogate mixed waste using polymer resins, HNF-SD-RE-TP-026 and to ensure adequacy of conduct and collection of samples and data. This testing will demonstrate the use of four different polyester vinyl ester resins in the solidification of surrogate liquid and dry wastes, similar to some mixed wastes generated by DOE operations

Wool-waste as organic nutrient source for container-grown plants

Energy Technology Data Exchange (ETDEWEB)

Zheljazkov, Valtcho D. [Mississippi State University, North Mississippi Research and Extension Center, Verona, MS 38879 (United States)], E-mail: vj40@pss.msstate.edu; Stratton, Glenn W [Department of Plant and Animal Sciences and Department of Environmental Sciences, Nova Scotia Agricultural College, Truro, NS, B2N 5E3 (Canada); Pincock, James [Department of Chemistry, Dalhousie University, Halifax, NS, B3H 4J3 (Canada); Butler, Stephanie [Department of Plant and Animal Sciences and Department of Environmental Sciences, Nova Scotia Agricultural College, Truro, NS, B2N 5E3 (Canada); Jeliazkova, Ekaterina A [Mississippi State University, Department of Plant and Soil Sciences, Mississippi State, MS 39762 (United States); Nedkov, Nedko K [Research Institute for Roses and Aromatic Crops, 49 Osvobojdenie Blv., Kazanluk (Bulgaria); Gerard, Patrick D [Department of Applied Economics and Statistics, Clemson University, Clemson, SC 29634 (United States)

2009-07-15

A container experiment was conducted to test the hypothesis that uncomposted wool wastes could be used as nutrient source and growth medium constituent for container-grown plants. The treatments were: (1) rate of wool-waste application (0 or unamended control, 20, 40, 80, and 120 g of wool per 8-in. pot), (2) growth medium constituents [(2.1) wool plus perlite, (2.2) wool plus peat, and (2.3) wool plus peat plus perlite], and (3) plant species (basil and Swiss chard). A single addition of 20, 40, 80, or 120 g of wool-waste to Swiss chard (Beta vulgaris L.) and basil (Ocimum basilicum L.) in pots with growth medium provided four harvests of Swiss chard and five harvests of basil. Total basil yield from the five harvests was 1.6-5 times greater than the total yield from the unamended control, while total Swiss chard yield from the four harvests was 2-5 times greater relative to the respective unamended control. The addition of wool-waste to the growth medium increased Swiss chard and basil tissue N, and NO{sub 3}-N and NH{sub 4}-N in growth medium relative to the unamended control. Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) microanalysis of wool fibers sampled at the end of the experiments indicated various levels of decomposition, with some fibers retaining their original surface structure. Furthermore, most of the wool fibers' surfaces contained significant concentrations of S and much less N, P, or K. SEM/EDX revealed that some plant roots grow directly on wool-waste fibers suggesting either (1) root directional growth towards sites with greater nutrient concentration and/or (2) a possible role for roots or root exudates in wool decomposition. Results from this study suggest that uncomposted wool wastes can be used as soil amendment, growth medium constituent, and nutrient source for container-grown plants.

Wool-waste as organic nutrient source for container-grown plants

International Nuclear Information System (INIS)

Zheljazkov, Valtcho D.; Stratton, Glenn W.; Pincock, James; Butler, Stephanie; Jeliazkova, Ekaterina A.; Nedkov, Nedko K.; Gerard, Patrick D.

2009-01-01

A container experiment was conducted to test the hypothesis that uncomposted wool wastes could be used as nutrient source and growth medium constituent for container-grown plants. The treatments were: (1) rate of wool-waste application (0 or unamended control, 20, 40, 80, and 120 g of wool per 8-in. pot), (2) growth medium constituents [(2.1) wool plus perlite, (2.2) wool plus peat, and (2.3) wool plus peat plus perlite], and (3) plant species (basil and Swiss chard). A single addition of 20, 40, 80, or 120 g of wool-waste to Swiss chard (Beta vulgaris L.) and basil (Ocimum basilicum L.) in pots with growth medium provided four harvests of Swiss chard and five harvests of basil. Total basil yield from the five harvests was 1.6-5 times greater than the total yield from the unamended control, while total Swiss chard yield from the four harvests was 2-5 times greater relative to the respective unamended control. The addition of wool-waste to the growth medium increased Swiss chard and basil tissue N, and NO 3 -N and NH 4 -N in growth medium relative to the unamended control. Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) microanalysis of wool fibers sampled at the end of the experiments indicated various levels of decomposition, with some fibers retaining their original surface structure. Furthermore, most of the wool fibers' surfaces contained significant concentrations of S and much less N, P, or K. SEM/EDX revealed that some plant roots grow directly on wool-waste fibers suggesting either (1) root directional growth towards sites with greater nutrient concentration and/or (2) a possible role for roots or root exudates in wool decomposition. Results from this study suggest that uncomposted wool wastes can be used as soil amendment, growth medium constituent, and nutrient source for container-grown plants.

Method of processing liquid waste containing fission product

International Nuclear Information System (INIS)

Funabashi, Kiyomi; Kawamura, Fumio; Matsuda, Masami; Komori, Itaru; Miura, Eiichi.

1988-01-01

Purpose: To prepare solidification products of low surface dose by removing cesium which is main radioactive nuclides from re-processing plants. Method: Liquid wastes containing a great amount of fission products are generated accompanying the reprocessing for spent nuclear fuels. After pH adjustment, the liquid wastes are sent to a concentrator to concentrate the dissolved ingredients. The concentrated liquid wastes are pumped to an adsorption tower in which radioactive cesium contributing much to the surface dose is removed. Then, the liquid wastes are sent by way of a surge tank to a mixing tank, in which they are mixed under stirring with solidifying agents such as cements. Then, the mixture is filled in a drum-can and solidified. According to this invention, since radioactive cesium is removed before solidification, it is possible to prepare solidification products at low surface dose and facilitate the handling of the solidification products. (Horiuchi, T.)

Risks attached to container- and bunker-storage of nuclear waste

International Nuclear Information System (INIS)

Jager, D. de

1987-12-01

The results are presented of a literature study into the risks attached to the two dry-storage options selected by the Dutch Central Organization For Radioactive Waste (COVRA): the container- and the bunker-storage for irradiated nuclear-fuel elements and nuclear waste. Since the COVRA does not make it clear how these concepts should have to be realized, the experiences abroad with dry interim-storage are considered. In particular the Castor-container-storage and the bunker storage proposed in the committee MINSK (Possibilities of Interim-storage in the Netherlands of Irradiated nuclear-fuel elements and Nuclear waste) are studied further in depth. The committee MINSK has performed a study into the technical realizability of various interim-storage facilities, among which a storage in bunkers. (author). 75 refs.; 14 figs.; 16 tabs

Cutting system for burnable poison rod

International Nuclear Information System (INIS)

Shiina, Atsushi; Toyama, Norihide; Koshino, Yasuo; Fujii, Toshio

1989-01-01

Burnable poison rods attached to spent fuels are contained in a containing box and transported to a receiving pool. The burnable poison rod-containing box is provisionally situated by the operation to a handling device to a provisional setting rack in a cutting pool and attached to a cutting guide of a cutting device upon cutting. The burnable poison rod is cut only in a cutting pool water and tritium generated upon cutting is dissolved into the cutting pool water. Diffusion of tritium is thus restricted. Further, the cutting pool is isolated by a partition device from the receiving pool during cutting of the burnable poison rod. Accordingly, water in which tritium is dissolved is inhibited from moving to the receiving pool and prevail of tritium contamination can be avoided. (T.M.)

Social life and sanitary risks: evolutionary and current ecological conditions determine waste management in leaf-cutting ants.

Science.gov (United States)

Farji-Brener, Alejandro G; Elizalde, Luciana; Fernández-Marín, Hermógenes; Amador-Vargas, Sabrina

2016-05-25

Adequate waste management is vital for the success of social life, because waste accumulation increases sanitary risks in dense societies. We explored why different leaf-cutting ants (LCA) species locate their waste in internal nest chambers or external piles, including ecological context and accounting for phylogenetic relations. We propose that waste location depends on whether the environmental conditions enhance or reduce the risk of infection. We obtained the geographical range, habitat and refuse location of LCA from published literature, and experimentally determined whether pathogens on ant waste survived to the high soil temperatures typical of xeric habitats. The habitat of the LCA determined waste location after phylogenetic correction: species with external waste piles mainly occur in xeric environments, whereas those with internal waste chambers mainly inhabit more humid habitats. The ancestral reconstruction suggests that dumping waste externally is less derived than digging waste nest chambers. Empirical results showed that high soil surface temperatures reduce pathogen prevalence from LCA waste. We proposed that LCA living in environments unfavourable for pathogens (i.e. xeric habitats) avoid digging costs by dumping the refuse above ground. Conversely, in environments suitable for pathogens, LCA species prevent the spread of diseases by storing waste underground, presumably, a behaviour that contributed to the colonization of humid habitats. These results highlight the adaptation of organisms to the hygienic challenges of social living, and illustrate how sanitary behaviours can result from a combination of evolutionary history and current environmental conditions. © 2016 The Author(s).

Under Water Thermal Cutting of the Moderator Vessel and Thermal Shield

International Nuclear Information System (INIS)

Loeb, A.; Sokcic-Kostic, M.; Eisenmann, B.; Prechtl, E.

2007-01-01

This paper presents the segmentation of the in 8 meter depth of water and for cutting through super alloyed moderator vessel and of the thermal shield of the MZFR stainless steel up to 130 mm wall thickness. Depending on the research reactor by means of under water plasma and contact arc metal cutting. The moderator vessel and the thermal shield are the most essential parts of the MZFR reactor vessel internals. These components have been segmented in 2005 by means of remotely controlled under water cutting utilizing a special manipulator system, a plasma torch and CAMC (Contact Arc Metal Cutting) as cutting tools. The engineered equipment used is a highly advanced design developed in a two years R and D program. It was qualified to cut through steel walls of more than 100 mm thickness in 8 meters water depth. Both the moderator vessel and the thermal shield had to be cut into such size that the segments could afterwards be packed into shielded waste containers each with a volume of roughly 1 m 3 . Segmentation of the moderator vessel and of the thermal shield was performed within 15 months. (author)

Process for denitrating waste solutions containing nitric acid actinides simultaneously separating the actinides

International Nuclear Information System (INIS)

Gompper, K.

1984-01-01

The invention should reduce the acid and nitrate content of waste solutions containing nitric acid as much as possible, should reduce the total salt content of the waste solution, remove the actinides contained in it by precipitation and reduce the α radio-activity in the remaining solution, without having to worry about strong reactions or an increase in the volume of the waste solution. The invention achieves this by mixing the waste solution with diethyl oxalate at room temperature and heating the mixture to at least 80 0 C. (orig.) [de

Phase formation during corrosion experiments with two simulated borosilicate nuclear waste glasses

International Nuclear Information System (INIS)

Haaker, R.F.

1985-10-01

Corrosion products resulting from the reaction of simulated high-level radioactive waste glasses with various solutions have been identified. At 200degC, in saturated NaCl, a degree of reaction of 10 g C31-3 glass or 2.6 g SON 68 glass per liter of solution was obtained. Analcime, vermiculite (a phyllosilicate) and a 2:1 zinc silicate are the major silica containing alteration products for the C31-3 glass. Analcime was the only silicate alteration product which could be identified for SON 68 glass. C31-3 glass appeared to be less reactive with a quinary brine containing Mg ++ than with NaCl. With the quinary brine, montmorillonite (a phyllosilicate) was the predominant silica containing alteration product. Hydrotalcite (a Mg-Al hydroxysulfate) and montmorillonite were the major Al-containing phases. A phyllosilicate, probably montmorillonite, was observed to form during the reaction of SON 68 glass with quinary brine. With either glass, modified NaCl brines which contained small amounts of MgCl 2 seem to have the effect of decreasing the amount of analcime and increasing the amount of phyllosilicate which is formed. In the case of C31-3 glass, there is approximately enough Mg, Al and Zn to precipitate most of the leached Si; measured Si concentrations remain well below that expected for amorphous silica. SON 68 glass has less Zn, Al and Mg than C31-3 glass and much higher Si concentrations of the leachates. (orig./RB)

Evaluation of potential mixed wastes containing lead, chromium, or used oil

International Nuclear Information System (INIS)

Siskind, B.; MacKenzie, D.R.; Bowerman, B.S.; Kempf, C.R.; Piciulo, P.L.

1987-01-01

This paper presents the results of follow-on studies conducted by Brookhaven National Laboratory (BNL) for the Nuclear Regulatory Commission (NRC) on certain kinds of low-level waste (LLW) which could also be classified as hazardous waste subject to regulation by the Environmental Protection Agency (EPA). Such LLW is termed ''mixed waste.'' Additional data have been collected and evaluated on two categories of potential mixed waste, namely LLW containing metallic lead and LLW containing chromium. Additionally, LLW with organic liquids, especially liquid scintillation wastes, are reviewed. In light of a proposed EPA rule to list used oil as hazardous waste, the potential mixed waste hazard of used oil contaminated with radionuclides is discussed. It is concluded that the EPA test for determining whether a solid waste exhibits the hazardous characteristic of extraction procedure toxicity does not adequately simulate the burial environment at LLW disposal sites, and in particular, does not adequately assess the potential for dissolution and transport of buried metallic lead. Also, although chromates are, in general, not a normal or routine constitutent in commercial LLW (with the possible exception of chemical decontamination wastes), light water reactors which do use chromates might find it beneficial to consider alternative corrosion inhibitors. In addition, it is noted that if used oil is listed by the EPA as hazardous waste, LLW oil may be managed by a scheme including one or more of the following processes: incineration, immobilization, sorption, aqueous extraction and glass furnace processing

Precipitation and Deposition of Aluminum-Containing Species in Tank Wastes

International Nuclear Information System (INIS)

Mattigod, Shas V.; Hobbs, David T.; Wang, Li-Qiong; Dabbs, Daniel M.; Aksay, Ilhan A.

2002-01-01

Aluminum-containing phases represent the most prevalent solids that can appear or disappear during the processing of radioactive tank wastes. Processes such as sludge washing and leaching are designed to dissolve Al-containing phases and thereby minimize the volume of high-level waste glass required to encapsulate radioactive sludges. Unfortunately, waste-processing steps that include evaporation can involve solutions that are supersaturated with respect to cementitious aluminosilicates that result in unwanted precipitation and scale formation. Of all the constituents of tank waste, limited solubility cementitious aluminosilicates have the greatest potential for clogging pipes and transfer lines, fouling highly radioactive components such as ion exchangers, and completely shutting down processing operations. For instance, deposit buildup and clogged drain lines experienced during the tank waste volume-reduction process at the Savannah River Site (SRS) required an evaporator to be shut down in October 1999. The Waste Processing Technology Section of Westinghouse Savannah River Company at SRS now is collaborating with team members from Pacific Northwest National Laboratory (PNNL) to verify the thermodynamic stability of aluminosilicate compounds under waste tank conditions in an attempt to solve the deposition and clogging problems. The primary objectives of this study are (1) to understand the major factors controlling precipitation, heterogeneous nucleation, and growth phenomena of relatively insoluble aluminosilicates; (2) to determine the role of organics for inhibiting aluminosilicate formation, and (3) to develop a predictive tool to control precipitation, scale formation, and cementation under tank waste processing conditions. The results of this work will provide crucial information for (1) avoiding problematical sludge processing steps and (2) identifying and developing effective technologies to process retrieved sludges and supernatants before ultimate

Containment of Solid Wastes in some Large Scandinavian Cities

DEFF Research Database (Denmark)

Du-Thinh, Kien

1998-01-01

to the geological-geotechnical characteristics of the subsoil of the waste sites which determine to a large extent the risks of infiltration and transport of leachates. The role of the barrier, its design and construction or the consequences arising from the lack of abarrier are dealt with herein. The monitoring......Two kinds of containment of solid wastes - one in the vicinity of Copenhagen, the capital of Denmark, another on the outskirts of Gothenburg, the second largest city of sweden - are reviewed in this article. They represent two different approaches to waste management. Special attention is given...

Treatment and minimization of heavy metal-containing wastes 1995

International Nuclear Information System (INIS)

Hager, J.P.; Mishra, B.; Litz, J.L.

1995-01-01

This symposium was held in conjunction with the 1995 Annual Meeting of the Minerals, Metals and Materials Society in Las Vegas, Nevada, February 12--16, 1995. The purpose of this meeting was to provide a forum for exchange of state-of-the-art information on treating and minimizing heavy metal-containing wastes. Papers were categorized under the following broad headings: aqueous processing; waste water treatment; thermal processing and stabilization; processing of fly ash, flue dusts, and slags; and processing of lead, mercury, and battery wastes. Individual papers have been processed separately for inclusion in the appropriate data bases

Direct releases to the surface and associated complementary cumulative distribution functions in the 1996 performance assessment for the Waste Isolation Pilot Plant: cuttings, cavings and spallings

International Nuclear Information System (INIS)

Berglund, J.W.; Garner, J.W.; Helton, J.C.; Johnson, J.D.; Smith, L.N.

2000-01-01

The following topics related to the treatment of cuttings, cavings and spallings releases to the surface environment in the 1996 performance assessment for the Waste Isolation Pilot Plant (WIPP) are presented: (i) mathematical description of models; (ii) uncertainty and sensitivity analysis results arising from subjective (i.e. epistemic) uncertainty for individual releases; (iii) construction of complementary cumulative distribution functions (CCDFs) arising from stochastic (i.e. aleatory) uncertainty; and (iv) uncertainty and sensitivity analysis results for CCDFs. The presented results indicate that direct releases due to cuttings, cavings and spallings do not constitute a serious threat to the effectiveness of the WIPP as a disposal facility for transuranic waste. Even when the effects of uncertain analysis inputs are taken into account, the CCDFs for cuttings, cavings and spallings releases fall substantially to the left of the boundary line specified in the US Environmental Protection Agency's standard for the geologic disposal of radioactive waste (40 CFR 191, 40 CFR 194)

Direct releases to the surface and associated complementary cumulative distribution functions in the 1996 performance assessment for the Waste Isolation Pilot Plant: Cuttings, cavings and spallings

International Nuclear Information System (INIS)

Berglund, J.W.; Garner, J.W.; Helton, Jon Craig; Johnson, J.D.; Smith, L.N.; Anderson, R.P.

2000-01-01

The following topics related to the treatment of cuttings, cavings and spallings releases to the surface environment in the 1996 performance assessment for the Waste Isolation Pilot Plant (WIPP) are presented: (1) mathematical description of models. (2) uncertainty and sensitivity analysis results arising from subjective (i.e., epistemic) uncertainty for individual releases, (3) construction of complementary cumulative distribution functions (CCDFs) arising from stochastic (i.e., aleatory) uncertainty, and (4) uncertainty and sensitivity analysis results for CCDFs. The presented results indicate that direct releases due to cuttings, cavings and spallings do not constitute a serious threat to the effectiveness of the WIPP as a disposal facility for transuranic waste. Even when the effects of uncertain analysis inputs are taken into account, the CCDFs for cuttings, cavings and spallings releases fall substantially to the left of the boundary line specified in the US Environmental Protection Agency standard for the geologic disposal of radioactive waste (40 CFR 191, 40 CFR 194)

Greater-than-Class C low-level radioactive waste shipping package/container identification and requirements study

International Nuclear Information System (INIS)

Tyacke, M.

1993-08-01

This report identifies a variety of shipping packages (also referred to as casks) and waste containers currently available or being developed that could be used for greater-than-Class C (GTCC) low-level waste (LLW). Since GTCC LLW varies greatly in size, shape, and activity levels, the casks and waste containers that could be used range in size from small, to accommodate a single sealed radiation source, to very large-capacity casks/canisters used to transport or dry-store highly radioactive spent fuel. In some cases, the waste containers may serve directly as shipping packages, while in other cases, the containers would need to be placed in a transport cask. For the purpose of this report, it is assumed that the generator is responsible for transporting the waste to a Department of Energy (DOE) storage, treatment, or disposal facility. Unless DOE establishes specific acceptance criteria, the receiving facility would need the capability to accept any of the casks and waste containers identified in this report. In identifying potential casks and waste containers, no consideration was given to their adequacy relative to handling, storage, treatment, and disposal. Those considerations must be addressed separately as the capabilities of the receiving facility and the handling requirements and operations are better understood

Lime treatment of liquid waste containing heavy metals, radionuclides and organics

International Nuclear Information System (INIS)

DuPont, A.

1990-01-01

This paper reports on lime treatment of liquid waste containing heavy metals, radio nuclides and organics. Lime is wellknown for its use in softening drinking water the treatment of municipal wastewaters. It is becoming important in the treatment of industrial wastewater and liquid inorganic hazardous waste; however, there are many questions regarding the use of lime for the treatment of liquid hazardous waste

Origin and evolution of cup-shaped structures on leached nuclear waste containment glass surfaces

International Nuclear Information System (INIS)

Dubois, C.; Villa, F.; Chambaudet, A.; Vernaz, E.

1994-01-01

A three-dimensional surface microanalysis system equipped with a sensitive topographical probe was used to quantify the evolution of cup-shaped structures formed by aqueous leaching of nuclear waste containment glass. A model of the dissolution phenomenon provides satisfactory correlation between calculated and measured cup radius and depth. Dissolution cups form from cracks on the initially cut glass surface. Large cracks control the phenomenon by forming the largest cups, which gradually absorb smaller ones. The evolution of the size and shape of the dissolution cups was described by a model that assumes a constant dissolution rate on the surface, diminishing with crack depth. The best fit with the experimental data was obtained with a dissolution rate one hundred times lower at the bottom of the crack than at the surface. Moreover, it is predictable that all the cups will gradually disappear as they grow larger and flatter over a leaching period of some 2 years, for the glass composition and experimental leaching procedures used in this work

Nanoporous Glasses for Nuclear Waste Containment

OpenAIRE

Woignier, Thierry; Primera, Juan; Reynes, Jerôme

2016-01-01

Research is in progress to incorporate nuclear waste in new matrices with high structural stability, resistance to thermal shock, and high chemical durability. Interactions with water are important for materials used as a containment matrix for the radio nuclides. It is indispensable to improve their chemical durability to limit the possible release of radioactive chemical species, if the glass structure is attacked by corrosion. By associating high structural stability and high chemical dura...

Design and testing of wood containers for radioactive waste

International Nuclear Information System (INIS)

Roberts, R.S.; Barry, P.E.

1981-01-01

A wood container for shipping and storing radioactive waste was designed to eliminate the problems caused by the weight, cost, and shape of the steel containers previously used. Tests specified by federal regulations (compression, free-drop, penetration, and vibration) were conducted on two of the containers, one loaded to 2500 lb and one loaded to 5000 lb. The 5000-lb container failed the free-drop test, but the 2500-lb container easily passed the tests and therefore qualifies as a Type A container. Its simplicity of design, low weight, and ease in handling have proved to be time-saving and cost-effective

Passive 3D imaging of nuclear waste containers with Muon Scattering Tomography

Science.gov (United States)

Thomay, C.; Velthuis, J.; Poffley, T.; Baesso, P.; Cussans, D.; Frazão, L.

2016-03-01

The non-invasive imaging of dense objects is of particular interest in the context of nuclear waste management, where it is important to know the contents of waste containers without opening them. Using Muon Scattering Tomography (MST), it is possible to obtain a detailed 3D image of the contents of a waste container on reasonable timescales, showing both the high and low density materials inside. We show the performance of such a method on a Monte Carlo simulation of a dummy waste drum object containing objects of different shapes and materials. The simulation has been tuned with our MST prototype detector performance. In particular, we show that both a tungsten penny of 2 cm radius and 1 cm thickness, and a uranium sheet of 0.5 cm thickness can be clearly identified. We also show the performance of a novel edge finding technique, by which the edges of embedded objects can be identified more precisely than by solely using the imaging method.

Structural optimization of reinforced concrete container for radioactive wastes

International Nuclear Information System (INIS)

Tamura, M.

1984-01-01

A structural optimization study of reinforced concrete container for transportation and disposal of the low level radioactive waste generated in Brazilian nuclear power plants. The code requires the structural integrity of these containers when subjected to fall from specified height, avoiding environmental contamination. The structural optimization allows material and transportation cost reduction by container wall thickness reduction. The structural analysis is performed by tridimensional mathematical model using finite element method. (Author) [pt

Design compliance matrix waste sample container filling system for nested, fixed-depth sampling system

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

This design compliance matrix document provides specific design related functional characteristics, constraints, and requirements for the container filling system that is part of the nested, fixed-depth sampling system. This document addresses performance, external interfaces, ALARA, Authorization Basis, environmental and design code requirements for the container filling system. The container filling system will interface with the waste stream from the fluidic pumping channels of the nested, fixed-depth sampling system and will fill containers with waste that meet the Resource Conservation and Recovery Act (RCRA) criteria for waste that contains volatile and semi-volatile organic materials. The specifications for the nested, fixed-depth sampling system are described in a Level 2 Specification document (HNF-3483, Rev. 1). The basis for this design compliance matrix document is the Tank Waste Remediation System (TWRS) desk instructions for design Compliance matrix documents (PI-CP-008-00, Rev. 0)

40 CFR 264.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

Science.gov (United States)

2010-07-01

... HAZARDOUS WASTE TREATMENT, STORAGE, AND DISPOSAL FACILITIES Landfills § 264.316 Disposal of small containers of hazardous waste in overpacked drums (lab packs). Small containers of hazardous waste in overpacked... hazardous waste in overpacked drums (lab packs). 264.316 Section 264.316 Protection of Environment...

40 CFR 265.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

Science.gov (United States)

2010-07-01

... OPERATORS OF HAZARDOUS WASTE TREATMENT, STORAGE, AND DISPOSAL FACILITIES Landfills § 265.316 Disposal of small containers of hazardous waste in overpacked drums (lab packs). Small containers of hazardous waste... hazardous waste in overpacked drums (lab packs). 265.316 Section 265.316 Protection of Environment...

Microbial control on decomposition of radionuclides-containing oily waste in soil

Science.gov (United States)

Selivanovskaya, Svetlana; Galitskaya, Polina

2014-05-01

The oily wastes are formed annually during extraction, refinement, and transportation of the oil and may cause pollution of the environment. These wastes contain different concentrations of waste oil (40-60%), waste water (30-90%), and mineral particles (5-40%). Some oily wastes also contain naturally occurring radionuclides which were incorporated by water that was pumped up with the oil. For assessment of the hazard level of waste treated soil, not only measurements of contaminants content are needed, because bioavailability of oily components varies with hydrocarbon type, and soil properties. As far as namely microbial communities control the decomposition of organic contaminants, biological indicators have become increasingly important in hazard assessment and the efficiency of remediation process. In this study the decomposition of radionuclides-containing oily waste by soil microbial communities were estimated. Waste samples collected at the Tikchonovskii petroleum production yard (Tatarstan, Russia) were mixed with Haplic greyzem soil at ratio 1:4 and incubated for 120 days. During incubation period, the total hydrocarbon content of the soil mixed with the waste reduced from 156 ± 48 g kg-1 to 54 ± 8 g kg-1 of soil. The concentrations of 226Ra and 232Th were found to be 643 ± 127, 254 ± 56 Bq kg-1 and not changed significantly during incubation. Waste application led to a soil microbial biomass carbon decrease in comparison to control (1.9 times after 1 day and 1.3 times after 120 days of incubation). Microbial respiration increased in the first month of incubation (up to 120% and 160% of control after 1 and 30 days, correspondingly) and decreased to the end of incubation period (74% of control after 120 days). Structure of bacterial community in soil and soil/waste mixture was estimated after 120 days of incubation using SSCP method. The band number decreased in contaminated soil in comparison to untreated soil. Besides, several new dominant DNA

Cellulose-containing Waste and Bituminized Salts

International Nuclear Information System (INIS)

Valcke, E.

2005-01-01

In Belgium, Medium-Level radioactive Waste (MLW) would be eventually disposed off in an underground repository in a geological formation such as the Boom Clay, which is studied as a reference host rock formation. MLW contains large quantities of non-radioactive chemicals that are released upon contact with pore water. It could be the case, for instance, for plutonium bearing cellulosic waste - such as paper tissues used to clean alpha glove boxes - issued from nuclear fuel fabrication (Belgonucleaire). At high pH, as in a disposal gallery backfilled with cement, the chemical degradation of cellulose will generate water-soluble products that may form strong complexes with actinides such as Am, Pu, Np, and U. This could lower the sorption of these elements onto the clay minerals, and hence increase their migration through the clay barrier. Another chemical perturbation could occur from the 3000 m 3 of so-called Eurobitum bituminised MLW, with precipitation sludges from the chemical treatment of spent nuclear fuel, and containing about 750 tons of NaNO 3 . The presence of NaNO 3 in this waste will give rise to several processes susceptible to affect the safety of the disposal system. Amongst others, it is necessary to verify that the swelling pressure of bitumen on the gallery wall and the osmotic pressure within the near-field are not too high to induce a fissuration of the host rock, leading to the formation of preferential migration pathways. The major objective of our work is to obtain a broad understanding of the different processes induced by the release of non-radioactive chemicals in the clay formation, to assess the chemical compatibility of different MLW forms with the clay

Preliminary selection criteria for the Yucca Mountain Project waste package container material

International Nuclear Information System (INIS)

Halsey, W.G.

1991-01-01

The Department of Energy's Yucca Mountain Project (YMP) is evaluating a site at Yucca Mountain in Nevada for construction of a geologic repository for the storage of high-level nuclear waste. Lawrence Livermore National Laboratory's (LLNL) Nuclear Waste Management Project (NWMP) has the responsibility for design, testing, and performance analysis of the waste packages. The design is performed in an iterative manner in three sequential phases (conceptual design, advanced conceptual design, and license application design). An important input to the start of the advanced conceptual design is the selection of the material for the waste containers. The container material is referred to as the 'metal barrier' portion of the waste package, and is the responsibility of the Metal Barrier Selection and Testing task at LLNL. The selection will consist of several steps. First, preliminary, material-independent selection criteria will be established based on the performance goals for the container. Second, a variety of engineering materials will be evaluated against these criteria in a screening process to identify candidate materials. Third, information will be obtained on the performance of the candidate materials, and final selection criteria and quantitative weighting factors will be established based on the waste package design requirements. Finally, the candidate materials will be ranked against these criteria to determine whether they meet the mandated performance requirements, and to provide a comparative score to choose the material for advanced conceptual design activities. This document sets forth the preliminary container material selection criteria to be used in screening candidate materials. 5 refs

Abrasive water jet cutting technique for biological shield concrete dismantlement

International Nuclear Information System (INIS)

Konno, T.; Narazaki, T.; Yokota, M.; Yoshida, H.; Miura, M.; Miyazaki, Y.

1987-01-01

The Japan Atomic Energy Research Institute (JAERI) is developing the abrasive-water jet cutting system to be applied to dismantling the biological shield walls of the JPDR as a part of the reactor dismantling technology development project. This is a total system for dismantling highly activated concrete. The concrete biological shield wall is cut into blocks by driving the abrasive-water jet nozzle, which is operated with a remote, automated control system. In this system, the concrete blocks are removed to a container, while the slurry and dust/mist which are generated during cutting are collected and treated, both automatically. It is a very practical method and will quite probably by used for actual dismantling of commercial power reactors in the future because it can minimize workers' exposure to radioactivity during dismantling, contributes to preventing diffusion of radiation, and reduces the volume of contaminated secondary waste

Hydrothermal waste package interactions with methane-containing basalt groundwater

International Nuclear Information System (INIS)

McGrail, B.P.

1984-01-01

Hydrothermal waste package interaction tests were conducted with a mixture of crushed glass, basalt, and steel in methane-containing synthetic basalt groundwater. In the absence of gamma radiolysis, methane was found to have little influence on the corrosion behavior of the waste package constituents. Under gamma radiolysis, methane was found to significantly lower the solution oxidation potential when compared to identical tests without methane. In addition, colloidal hydrocarbon polymers that have been produced under the irradiation conditions of these experiments were not formed. The presence of the waste package constituents apparently inhibited the formation of the polymers. However, the mechanism which prevented their formation was not determined

Stabilization/solidification of synthetic Nigerian drill cuttings | Opete ...

African Journals Online (AJOL)

Stabilization/solidification of synthetic Nigerian drill cuttings. SEO Opete, IA Mangibo, ET Iyagba. Abstract. In the Nigerian oil and gas industry, large quantities of oily and synthetic drill cuttings are produced annually. These drill cuttings are heterogeneous wastes which comprises of hydrocarbons, heavy metals and ...

Application of fuel cell for pyrite and heavy metal containing mining waste

Science.gov (United States)

Keum, H.; Ju, W. J.; Jho, E. H.; Nam, K.

2015-12-01

Once pyrite and heavy metal containing mining waste reacts with water and air it produces acid mine drainage (AMD) and leads to the other environmental problems such as contamination of surrounding soils. Pyrite is the major source of AMD and it can be controlled using a biological-electrochemical dissolution method. By enhancing the dissolution of pyrite using fuel cell technology, not only mining waste be beneficially utilized but also be treated at the same time by. As pyrite-containing mining waste is oxidized in the anode of the fuel cell, electrons and protons are generated, and electrons moves through an external load to cathode reducing oxygen to water while protons migrate to cathode through a proton exchange membrane. Iron-oxidizing bacteria such as Acidithiobacillus ferrooxidans, which can utilize Fe as an electron donor promotes pyrite dissolution and hence enhances electrochemical dissolution of pyrite from mining waste. In this study mining waste from a zinc mine in Korea containing 17 wt% pyrite and 9% As was utilized as a fuel for the fuel cell inoculated with A. ferrooxidans. Electrochemically dissolved As content and chemically dissolved As content was compared. With the initial pH of 3.5 at 23℃, the dissolved As concentration increased (from 4.0 to 13 mg/L after 20 d) in the fuel cell, while it kept decreased in the chemical reactor (from 12 to 0.43 mg/L after 20 d). The fuel cell produced 0.09 V of open circuit voltage with the maximum power density of 0.84 mW/m2. Dissolution of As from mining waste was enhanced through electrochemical reaction. Application of fuel cell technology is a novel treatment method for pyrite and heavy metals containing mining waste, and this method is beneficial for mining environment as well as local community of mining areas.

French processes for waste embedding. The use of epoxy resin for waste containment

International Nuclear Information System (INIS)

Augustin, X.; Gauthey, J.C.

1993-01-01

The low- and medium-level wastes generated by nuclear facilities when operating as well as during their decommissioning (dismantling, decontamination, etc.) are embedded for the purpose of obtaining a product suitable for disposal. Due to the varieties of waste produced, it was necessary to resort to multi-purpose techniques to solve problems relating to their embedding. The process for waste embedding in thermosetting polymer (polyester, epoxy) developed by the French Atomic Energy Commission (CEA) and its subsidiary TECHNICATOME is easy to operate and yields excellent results having regard to volume reduction and containment of radioisotopes (particularly caesium). The industrial development of this process has led to the design of small, flexible, fixed or mobile, embedding stations. Examples illustrating the increasing use of this process during facility dismantling are described

Processing method and processing device for liquid waste containing surface active agent and radioactive material

International Nuclear Information System (INIS)

Nishi, Takashi; Matsuda, Masami; Baba, Tsutomu; Yoshikawa, Ryozo; Yukita, Atsushi.

1998-01-01

Washing liquid wastes containing surface active agents and radioactive materials are sent to a deaerating vessel. Ozone is blown into the deaerating vessel. The washing liquid wastes dissolved with ozone are introduced to a UV ray irradiation vessel. UV rays are irradiated to the washing liquid wastes, and hydroxy radicals generated by photodecomposition of dissolved ozone oxidatively decompose surface active agents contained in the washing liquid wastes. The washing liquid wastes discharged from the UV ray irradiation vessel are sent to an activated carbon mixing vessel and mixed with powdery activated carbon. The surface active agents not decomposed in the UV ray irradiation vessel are adsorbed to the activated carbon. Then, the activated carbon and washing liquid wastes are separated by an activated carbon separating/drying device. Radioactive materials (iron oxide and the like) contained in the washing liquid wastes are mostly granular, and they are separated and removed from the washing liquid wastes in the activated carbon separating/drying device. (I.N.)

Russian Containers for Transportation of Solid Radioactive Waste

International Nuclear Information System (INIS)

Petrushenko, V. G.; Baal, E. P.; Tsvetkov, D. Y.; Korb, V. R.; Nikitin, V. S.; Mikheev, A. A.; Griffith, A.; Schwab, P.; Nazarian, A.

2002-01-01

The Russian Shipyard ''Zvyozdochka'' has designed a new container for transportation and storage of solid radioactive wastes. The PST1A-6 container is cylindrical shaped and it can hold seven standard 200-liter (55-gallon) drums. The steel wall thickness is 6 mm, which is much greater than standard U.S. containers. These containers are fully certified to the Russian GOST requirements, which are basically identical to U.S. and IAEA standards for Type A containers. They can be transported by truck, rail, barge, ship, or aircraft and they can be stacked in 6 layers in storage facilities. The first user of the PST1A-6 containers is the Northern Fleet of the Russian Navy, under a program sponsored jointly by the U.S. DoD and DOE. This paper will describe the container design and show how the first 400 containers were fabricated and certified

Decontamination flowsheet development for a waste oil containing mixed radioactive contaminants

International Nuclear Information System (INIS)

Vijayan, S.; Buckley, L.P.

1993-01-01

The majority of waste oils contaminated with both radioactive and hazardous components are generated in nuclear power plant, research lab. and uranium-refinery operations. The waste oils are complex, requiring a detailed examination of the waste management strategies and technology options. It may appear that incineration offers a total solution, but this may not be true in all cases. An alternative approach is to decontaminate the waste oils to very low contaminant levels, so that the treated oils can be reused, burned as fuel in boilers, or disposed of by commercial incineration. This paper presents selected experimental data and evaluation results gathered during the development of a decontamination flowsheet for a specific waste oil stores at Chalk River Labs. (CRL). The waste oil contains varying amounts of lube oils, grease, paint, water, particulates, sludge, light chloro- and fluoro-solvents, polychlorinated biphenyls (PCB), complexing chemicals, uranium, chromium, iron, arsenic and manganese. To achieve safe management of this radioactive and hazardous waste, several treatment and disposal methods were screened. Key experiments were performed at the laboratory-scale to confirm and select the most appropriate waste-management scheme based on technical, environmental and economic criteria. The waste-oil-decontamination flowsheet uses a combination of unit operations, including prefiltration, acid scrubbing, and aqueous-leachage treatment by precipitation, microfiltration, filter pressing and carbon adsorption. The decontaminated oil containing open-quotes de minimisclose quotes levels of contaminants will undergo chemical destruction of PCBs and final disposal by incineration. The recovered uranium will be recycled to a uranium milling process

Method for ultimate disposition of borate containing radioactive wastes by vitrification

International Nuclear Information System (INIS)

Bege, D.; Faust, H.J.; Puthawala, A.; Stunkel, H.

1984-01-01

Method for the ultimate disposition of radioactive wastes by vitrification, in which weak to medium radioactive waste concentrates from borate-containing radioactive liquids are mixed with added glass-forming materials, maximally in a ratio of 1:3, and the mixture heated to obtain a glass-forming melt

Radiolysis effects on fuel corrosion within a failed nuclear waste container

International Nuclear Information System (INIS)

Sunder, S.; Shoeshmith, D.W.; Christensen, H.C.

2003-01-01

The concept of geological disposal of used nuclear fuel in corrosion resistant containers is being investigated in several countries. In the Canadian Nuclear Fuel Waste Management Program (CNFWMP), it is assumed that the used fuel will be disposed of in copper containers. Since the predicted lifetimes of these containers are very long (>106 years), only those containers emplaced with an undetected defect will fail within the period for which radionuclide release from the fuel must be considered. Early failure could lead to the entry of water into the container and subsequent release of radionuclides. The release rate of radionuclides from the used fuel will depend upon its dissolution rate. The primary mechanism for release will be the corrosion of the fuel driven by radiolytically-produced oxidants. The studies carried out to determine the effects of water radiolysis on fuel corrosion are reviewed, and some of the procedures used to predict corrosion rates of used fuel in failed nuclear waste containers described. (author)

Destruction of high explosives and wastes containing high explosives using the molten salt destruction process

International Nuclear Information System (INIS)

Upadhye, R.S.; Brummond, W.A.; Pruneda, C.O.

1992-01-01

This paper reports the Molten Salt Destruction (MSD) Process which has been demonstrated for the destruction of HE and HE-containing wastes. MSD has been used by Rockwell International and by Anti-Pollution Systems to destroy hazardous wastes. MSD converts the organic constituents (including the HE) of the waste into non-hazardous substances such as carbon dioxide, nitrogen and water. In the case of HE-containing mixed wastes, any actinides in the waste are retained in the molten salt, thus converting the mixed wastes into low-level wastes. (Even though the MSD process is applicable to mixed wastes, this paper will emphasize HE-treatment.) The destruction of HE is accomplished by introducing it, together with oxidant gases, into a crucible containing a molten salt, such as sodium carbonate, or a suitable mixture of the carbonates of sodium, potassium, lithium and calcium. The temperature of the molten salt can be between 400 to 900 degrees C. The combustible organic components of the waste react with oxygen to produce carbon dioxide, nitrogen and steam

Detection of free liquid in containers of solidified radioactive waste

Science.gov (United States)

Greenhalgh, Wilbur O.

1985-01-01

A method of nondestructively detecting the presence of free liquid within a sealed enclosure containing solidified waste by measuring the levels of waste at two diametrically opposite locations while slowly tilting the enclosure toward one of said locations. When the measured level remains constant at the other location, the measured level at said one location is noted and any measured difference of levels indicates the presence of liquid on the surface of the solidified waste. The absence of liquid in the enclosure is verified when the measured levels at both locations are equal.

Detection of free liquid in containers of solidified radioactive waste

Science.gov (United States)

Greenhalgh, W.O.

Nondestructive detection of the presence of free liquid within a sealed enclosure containing solidified waste is accomplished by measuring the levels of waste at two diametrically opposite locations while slowly tilting the enclosure toward one of said locations. When the measured level remains constant at the other location, the measured level at said one location is noted and any measured difference of levels indicates the presence of liquid on the surface of the solifified waste. The absence of liquid in the enclosure is verified when the measured levels at both locations are equal.

Investigation of Properties of Asphalt Concrete Containing Boron Waste as Mineral Filler

Directory of Open Access Journals (Sweden)

Cahit GÜRER

2016-05-01

Full Text Available During the manufacture of compounds in the boron mining industry a large quantity of waste boron is produced which has detrimental effects on the environment. Large areas have to be allocated for the disposal of this waste. Today with an increase in infrastructure construction, more efficient use of the existing sources of raw materials has become an obligation and this involves the recycling of various waste materials. Road construction requires a significant amount of raw materials and it is possible that substantial amounts of boron-containing waste materials can be recycled in these applications. This study investigates the usability of boron wastes as filler in asphalt concrete. For this purpose, asphalt concrete samples were produced using mineral fillers containing 4%, 5%, 6%, 7% and 8% boron waste as well as a 6% limestone filler (6%L as the control sample. The Marshall Design, mechanical immersion and Marshall Stability test after a freeze-thaw cycle and indirect tensile stiffness modulus (ITSM test were performed for each of the series. The results of this experimental study showed that boron waste can be used in medium and low trafficked asphalt concrete pavements wearing courses as filler.

Cost savings associated with landfilling wastes containing very low levels of uranium

International Nuclear Information System (INIS)

Boggs, C.J.; Shaddoan, W.T.

1996-01-01

The Paducah Gaseous Diffusion Plant (PGDP) has operated captive landfills (both residential and construction/demolition debris) in accordance with the Commonwealth of Kentucky regulations since the early 1980s. Typical waste streams allowed in these landfills include nonhazardous industrial and municipal solid waste (such as paper, plastic, cardboard, cafeteria waste, clothing, wood, asbestos, fly ash, metals, and construction debris). In July 1992, the U.S. Environmental Protection Agency issued new requirements for the disposal of sanitary wastes in a open-quotes contained landfill.close quotes These requirements were promulgated in the 401 Kentucky Administrative Record Chapters 47 and 48 that became effective 30 June 1995. The requirements for a new contained landfill include a synthetic liner made of high-density polyethylene in addition to the traditional 1-meter (3-foot) clay liner and a leachate collection system. A new landfill at Paducah would accept waste streams similar to those that have been accepted in the past. The permit for the previously existing landfills did not include radioactivity limits; instead, these levels were administratively controlled. Typically, if radioactivity was detected above background levels, the waste was classified as low-level waste (LLW), which would be sent off-site for disposal

Diffusion of calcium in pure and doped NaCl; Diffusion du calcium dans NaCl pur et dope

Energy Technology Data Exchange (ETDEWEB)

Slifkin, L; Brebec, G [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1969-07-01

We have determined, by diffusion experiments of Ca in pure and doped NaCl, the activation energy for the calcium jumps and the binding energy between calcium ion and vacancy. (authors) [French] Nous avons determine, par des mesures de diffusion du Ca dans NaCl pur et NaCl dope avec CaCl{sub 2}, l'energie d'activation relative aux sauts du calcium et l'energie de liaison lacune-calcium. (auteurs)

Effects of a potential drop of a shipping cask, a waste container, and a bare fuel assembly during waste-handling operations

International Nuclear Information System (INIS)

Wu, C.L.; Lee, J.; Lu, D.L.; Jardine, L.J.

1991-12-01

This study investigates the effects of potential drops of a typical shipping cask, waste container, and bare fuel assembly during waste-handling operations at the prospective Yucca Mountain Repository. The waste-handling process (one stage, no consolidation configuration) is examined to estimate the maximum loads imposed on typical casks and containers as they are handled by various pieces of equipment during waste-handling operations. Maximum potential drop heights for casks and containers are also evaluated for different operations. A nonlinear finite-element model is employed to represent a hybrid spent fuel container subject to drop heights of up to 30 ft onto a reinforced concrete floor. The impact stress, strain, and deformation are calculated, and compared to the failure criteria to estimate the limiting (maximum permissible) drop height for the waste container. A typical Westinghouse 17 x 17 PWR fuel assembly is analyzed by a simplified model to estimate the energy absorption by various parts of the fuel assembly during a 30 ft drop, and to determine the amount of kinetic energy in a fuel pin at impact. A nonlinear finite-element analysis of an individual fuel pin is also performed to estimate the amount of fuel pellet fracture due to impact. This work was completed on May 1990

Self-consolidating concretes containing waste PET bottles as sand replacement

Science.gov (United States)

Khalid, Faisal Sheikh; Azmi, Nurul Bazilah; Mazenan, Puteri Natasya; Shahidan, Shahiron; Othman, Nor hazurina; Guntor, Nickholas Anting Anak

2018-02-01

This study evaluates the effect of self-consolidating concrete (SCC) containing waste polyethylene terephthalate (PET) granules on the fresh, mechanical and water absorption properties. Fine aggregates were replaced from 0% to 8% by PET granules. The fresh properties of SCC containing PET granules were determined using slump flow and V-funnel flow time tests. The compressive and splitting tensile strength were evaluated. The results indicated that utilization of waste PET granules in production of SCC could be an effective way for recycling purpose. The maximum amount of PET replacement should be limited to 5%. Exceeding 5% of PET content may result in an increase of V-funnel flow time to overpass the limiting value, decrease in strength. The production of high performance SCC containing 5% PET granules satisfies all the requirements for SCC with satisfactory outputs.

Buffer lining manufacturing method for radioactive waste container

International Nuclear Information System (INIS)

Kawakami, Susumu; Sugino, Hiroyuki

1998-01-01

A recessed portion is formed on an upper surface of a filler layer made of a buffer powder filled into a container main body, the upper portion of the vessel main body is closed by a shrinkable liquid tight film. It is placed in a pressurizing container and pressed to mold a buffer lining base material integrated with the vessel main body. A flat upper surface and a containing space are formed by shaving to form a buffer lining. A disposing vessel containing radioactive wastes is inserted into the containing space, and the containing space is closed by a buffer block. The upper surface is sealed by a lid. With such a constitution, since a buffer lining integrated with the vessel main body can be formed easily inside the vessel main body, the disposing vessel can be contained in the containing vessel in a state surrounded by the buffer easily and stably without laying or piling over a large quantity of buffer blocks. (T.M.)

Assembly procedure for column cutting platform

International Nuclear Information System (INIS)

Routh, R.D.

1995-01-01

This supporting document describes the assembly procedure for the Column Cutting Platform and Elevation Support. The Column Cutting Platform is a component of the 241-SY-101 Equipment Removal System. It is set up on the deck of the Strongback Trailer to provide work access to cut off the upper portion of the Mitigation Pump Assembly (MPA). The Elevation Support provides support for the front of the Storage Container with the Strongback at an inclined position. The upper portion of the MPA must be cut off to install the Containment Caps on the Storage Container. The storage Container must be maintained in an inclined position until the Containment Caps are installed to prevent any residual liquids from migrating forward in the Storage Container

Disposal of nuclear wastes

International Nuclear Information System (INIS)

Albrecht, E.; Kuehn, K.

1977-01-01

Final storage of nuclear wastes in the salt mine at Asse is described. Until the end of 1976, all in all 73,000 containers with slightly radioactive wastes were deposited there within the framework of a test programme - the Asse pit is a pilot plant. Final storage of medium active waste was started in 1972. So far, about 1,150 barrels with medium active waste were deposited. Storage techniques applied, radiation exposure of the personnel and experience gained so far are reported on in this context. Final storage at Asse of highly active wastes developing decay heat is still in a preparatory stage, as here radiation as well as heat problems have to be mastered. Technical mining activities for the recoverable storage of highly-active, heat-developing wastes in the form of ceramic glasses are still in a planning phase, whereas advance work, e.g. cutting storage chambers out of seams 775 m thick have already begun. (HPH) [de

Impact of NaCl reduction in Danish semi-hard Samsoe cheeses on development and autolysis of DL-starter cultures

DEFF Research Database (Denmark)

Søndergaard, Lise; Ryssel, Mia; Svendsen, Carina

2015-01-01

of two commercial DL-starter cultures (C1 and C2) used in the production of Danish semi-hard Samsoe cheeses were affected by reduced NaCl levels. Cheeses containing .... Lactic acid bacteria (LAB), distribution of bacteria as single cells or microcolonies, their viability in the cheeses and cell autolysis were monitored during ripening, as well as the impact of NaCl content and autolysis on the formation of free amino acids (FAA). Reduction of NaCl resulted in higher LAB...

Process for treating waste water containing hydrazine from power stations

International Nuclear Information System (INIS)

Hoffmann, W.

1982-01-01

A process for treating waste water containing hydrazine from nuclear power stations is proposed, characterized by the fact that the water is taken continuously through a water decomposition cell. If the water does not have sufficient conductivity itself, a substance raising the electrical conductivity is added to the water to be treated. The electrolysis is situated in the waste water tank. (orig./RB) [de

Data acquisition testing in supercritical water oxidation using machine cutting oils and metals

International Nuclear Information System (INIS)

Garcia, K.M.

1996-01-01

The Department of Energy, the Navy, and SERDP provided funding for an extensive series of testing of a Supercritical Water Oxidation (SCWO) system. The goal of the testing was to create performance data on the process when dealing with highly chlorinated wastes containing heavy metals, and radionuclides. The testing was performed in a MODAR vessel oxidizer. Performance was measured by the ability of the process to achieve greater than 99.99% destruction of the organic content, to partition the metals and radionuclide surrogates for mass balance, and survive the highly corrosive species in the effluent. The test data has shown that these goals were accomplished. 30 gal/day of highly chlorinated machine cutting oil was treated for 130 hrs. There were no significant corrosion or solids handling problems. This machine cutting oil, TRIM reg-sign SOL was chosen by DOE for its complex nature and has proven to be one of the more refractory organic feeds encountered by MODAR. The Navy provided 8 waste streams collected from their shore facilities operation. These paints varied in solids content with wastes such as paint chips, and adhesives. The ninth test run was with all 8 series of wastes combined. The MODAR system successfully treated all of these waste streams providing performance data on the ability of SCWO to treat difficult sludges

In situ vitrification of buried waste: Containment issues and suppression systems

International Nuclear Information System (INIS)

Luey, J.; Powell, T.D.

1992-03-01

Pacific Northwest Laboratory (PNL) and Idaho National Engineering Laboratory (INEL) are developing a remedial action technology for buried waste through the adaptation of the in situ vitrification (ISV) process. The ISV process is a thermal treatment process originally developed for the US Department of Energy (DOE) to stabilize soils contaminated with transuranic waste. ISV tests with buried waste forms have demonstrated that the processing of buried waste is more dynamic than the processing of soils. This paper will focus on the issue of containment of the gases released during the processing of buried waste and on engineered suppression systems to alleviate transient events associated with dynamic off-gassing from the ISV melt

In situ vitrification of buried waste: Containment issues and suppression systems

International Nuclear Information System (INIS)

Luey, J.; Powell, T.D.

1992-01-01

Pacific Northwest Laboratory (PNL) and Idaho National Engineering Laboratory (INEL) are developing a remedial action technology for buried waste through the adaptation of the in situ vitrification (ISV) process. The ISV process is a thermal treatment process originally developed for the U.S. Department of Energy (DOE) to stabilize soils contaminated with transuranic waste. ISV tests with buried waste forms have demonstrated that the processing of buried waste is more dynamic than the processing of soils. This paper will focus on the issue of containment of the gases released during the processing of buried waste and on engineered suppression systems to alleviate transient events associated with dynamic off-gassing from the ISV melt. (author)

A batch assay to measure microbial hydrogen sulfide production from sulfur-containing solid wastes

International Nuclear Information System (INIS)

Sun, Mei; Sun, Wenjie; Barlaz, Morton A.

2016-01-01

Large volumes of sulfur-containing wastes enter municipal solid waste landfills each year. Under the anaerobic conditions that prevail in landfills, oxidized forms of sulfur, primarily sulfate, are converted to sulfide. Hydrogen sulfide (H 2 S) is corrosive to landfill gas collection and treatment systems, and its presence in landfill gas often necessitates the installation of expensive removal systems. For landfill operators to understand the cost of managing sulfur-containing wastes, an estimate of the H 2 S production potential is needed. The objective of this study was to develop and demonstrate a biochemical sulfide potential (BSP) test to measure the amount of H 2 S produced by different types of sulfur-containing wastes in a relatively fast (30 days) and inexpensive (125 mL serum bottles) batch assay. This study confirmed the toxic effect of H 2 S on both sulfate reduction and methane production in batch systems, and demonstrated that removing accumulated H 2 S by base adsorption was effective for mitigating inhibition. H 2 S production potentials of coal combustion fly ash, flue gas desulfurization residual, municipal solid waste combustion ash, and construction and demolition waste were determined in BSP assays. After 30 days of incubation, most of the sulfate in the wastes was converted to gaseous or aqueous phase sulfide, with BSPs ranging from 0.8 to 58.8 mL H 2 S/g waste, depending on the chemical composition of the samples. Selected samples contained solid phase sulfide which contributed to the measured H 2 S yield. A 60 day incubation in selected samples resulted in 39–86% additional sulfide production. H 2 S production measured in BSP assays was compared with that measured in simulated landfill reactors and that calculated from chemical analyses. H 2 S production in BSP assays and in reactors was lower than the stoichiometric values calculated from chemical composition for all wastes tested, demonstrating the importance of assays to estimate the

Recovery Of Chromium Metal (VI) Using Supported Liquid Membrane (SLM) Method, A study of Influence of NaCl and pH in Receiving Phase on Transport

Science.gov (United States)

Cholid Djunaidi, Muhammad; Lusiana, Retno A.; Rahayu, Maya D.

2017-06-01

Chromium metal(VI) is a valuable metal but in contrary has high toxicity, so the separation and recovery from waste are very important. One method that can be used for the separation and recovery of chromium (VI) is a Supported Liquid Membrane (SLM). SLM system contains of three main components: a supporting membrane, organic solvents and carrier compounds. The supported Membrane used in this research is Polytetrafluoroethylene (PTFE), organic solvent is kerosene, and the carrier compound used is aliquat 336. The supported liquid membrane is placed between two phases, namely, feed phase as the source of analyte (Cr(VI)) and the receiving phase as the result of separation. Feed phase is the electroplating waste which contains of chromium metal with pH variation about 4, 6 and 9. Whereas the receiving phase are the solution of HCl, NaOH, HCl-NaCl and NaOH-NaCl with pH variation about 1, 3, 5 and 7. The efficiency separation is determined by measurement of chromium in the feed and the receiving phase using AAS (Atomic Absorption Spectrophotometry). The experiment results show that transport of Chrom (VI) by Supported Liquid membrane (SLM) is influenced by pH solution in feed phase and receiving phase as well as NaCl in receiving phase. The highest chromium metal is transported from feed phase about 97,78%, whereas in receiving phase shows about 58,09%. The highest chromium metal transport happens on pH 6 in feed phase, pH 7 in receiving phase with the mixture of NaOH and NaCl using carrier compound aliquat 336.

Criticality Potential of Waste Packages Containing DOE SNF Affected by Igneous Intrusion

International Nuclear Information System (INIS)

D.S. Kimball; C.E. Sanders

2006-01-01

The Department of Energy (DOE) is currently preparing an application to submit to the U.S. Nuclear Regulatory Commission for a construction authorization for a monitored geologic repository. The repository will contain spent nuclear fuel (SNF) and defense high-level waste (DHLW) in waste packages placed in underground tunnels, or drifts. The primary objective of this paper is to perform a criticality analysis for waste packages containing DOE SNF affected by a disruptive igneous intrusion event in the emplacement drifts. The waste packages feature one DOE SNF canister placed in the center and surrounded by five High-Level Waste (HLW) glass canisters. The effective neutron multiplication factor (k eff ) is determined for potential configurations of the waste package during and after an intrusive igneous event. Due to the complexity of the potential scenarios following an igneous intrusion, finding conservative and bounding configurations with respect to criticality requires some additional considerations. In particular, the geometry of a slumped and damaged waste package must be examined, drift conditions must be modeled over a range of parameters, and the chemical degradation of DOE SNF and waste package materials must be considered for the expected high temperatures. The secondary intent of this calculation is to present a method for selecting conservative and bounding configurations for a wide range of end conditions

Properties of concrete containing foamed concrete block waste as fine aggregate replacement

Science.gov (United States)

Muthusamy, K.; Budiea, A. M. A.; Zaidan, A. L. F.; Rasid, M. H.; Hazimmah, D. S.

2017-11-01

Environmental degradation due to excessive sand mining dumping at certain places and disposal of foamed concrete block waste from lightweight concrete producing industry are issues that should be resolved for a better and cleaner environment of the community. Thus, the main intention of this study is to investigate the potential of foamed concrete block waste as partial sand replacement in concrete production. The foamed concrete waste (FCW) used in this research that were supplied by a local lightweight concrete producing industry. The workability and compressive strength of concrete containing various percentage of foamed concrete waste as partial sand replacement has been investigated. Prior to the use, the foamed concrete waste were crushed to produce finer particles. Six concrete mixes containing various content of crushed foamed concrete waste that are 0%, 10%, 20%, 30%, 40% and 50% were used in this experimental work. Then the prepared specimens were placed in water curing until the testing age. Compressive strength test and flexural strength tests were conducted at 7, 14 and 28 days. The result shows that integration of crushed foamed concrete waste as partial sand replacement in concrete reduces the mix workability. It is interesting to note that both compressive strength and flexural strength of concrete improves when 30% crushed foamed concrete waste is added as partial sand replacement.

Problems of comprehensive use of waste hydrogen-containing gas in petrochemistry

Energy Technology Data Exchange (ETDEWEB)

Kulikov, V M; Grabovskiy, O G; Yevplanov, A I

1979-01-01

At enterprises of the Ministry of the Petrochemical Industry, gas wastes, containing 60-70% CH/sub 4/ and 25-30% H/sub 2/, are practically completely used as boiler and furnace fuel. The situation is different with gases with a high H/sub 2/ content. Gases containing 70-90% H/sub 2/ are not used, and are emitted into the atmosphere. The gases are not detoxified by burning in torches, and the air basin is polluted by organic compounds contained in these gases that are harmful to people's health. Emitting combustible gases into the atmosphere is the result of fears of burning gases with a high H/sub 2/ content in burners designed to burn gases at a slower flame propagation speed, as well as a low gas pressure and their uneven exit. At the Kuybyshev synthetic alcohol plant, waste gases of the following composition (rounded) are formed: H2, 76; CH4, 8; C2H4, 7; C3H8, 1; CO2, 8%. The gas also contains fractions of a percent of ethane, propane, butylene and butadiene. The lowest combustion heat of 1 cubic meter of gas under normal conditions is 3875 kcal. The gas pressure is 0.2 kg-force/square cm. About 1500 cubic meters of gas form per hour. A hearth fantail burner developed by the Kuybyshev Polytechnical Institute is suggested for burning waste gas. Using waste gases in the petrochemical industry will enable a savings of less than or equal to 60,000 tons of equivalent fuel per year.

Hydrothermal waste package interactions with methane-containing basalt groundwater

International Nuclear Information System (INIS)

McGrail, B.P.

1984-11-01

Hydrothermal waste package interaction tests with methane-containing synthetic basalt groundwater have shown that in the absence of gamma radiolysis, methane has little influence on the glass dissolution rate. Gamma radiolysis tests at fluxes of 5.5 x 10 5 and 4.4 x 10 4 R/hr showed that methane-saturated groundwater was more reducing than identical experiments where Ar was substituted for CH 4 . Dissolved methane, therefore, may be beneficial to the waste package in limiting the solubility of redox sensitive radionuclides such a 99 Tc. Hydrocarbon polymers known to form under the irradiation conditions of these tests were not produced. The presence of the waste package constituents apparently inhibited the formation of the polymers, however, the mechanism which prevented their formation was not determined

An assessment of the feasibility of indefinite containment of Canadian nuclear fuel wastes

International Nuclear Information System (INIS)

Shoesmith, D.W.; King, F.; Ikeda, B.M.

1995-05-01

This report presents an analysis of the expected corrosion behaviour of nuclear fuel waste containers in a conceptual Canadian disposal vault. The container materials considered are dilute Ti alloys (Grades-2, -12 and -16) and oxygen-free copper. The corrosive conditions within the disposal vault change with time as the initially trapped oxygen is consumed and as the heat and γ-radiation produced by the waste decays. This evolution of the vault environment is broadly classified into an early, warm and oxidizing period followed by a period of long-term, stable, cool and non-oxidizing conditions. The corrosion behaviour of both types of material during these two periods is discussed, and various models that have been developed to predict the lifetimes of the containers are presented. The conclusion is that indefinite containment of the waste is feasible with both copper and titanium alloys under Canadian disposal conditions. (author). refs., tabs., figs

Asia/Pacific moves to address mountainous waste problem

International Nuclear Information System (INIS)

Chynoweth, E.

1993-01-01

There is a serious lack of chemical waste treatment units in the Asia/Pacific region. In many countries a lack of infrastructure, coupled with scant or no legislation or enforcement, results in significant amounts of chemical waste being dumped without proper treatment. The exception is Japan, which has substantial incineration, treatment, and landfill capabilities. Japan's chemical industry generates more than 14 million m.t./year of waste, which is reduced to 2.51 million m.t./year after treatment and recycling. Chemical companies operating in Asia/Pacific countries that do not have authorized waste contractors and disposal plants have few options. They can treat wastes inhouse, increase recycling, ship wastes outside for treatment, or store wastes onsite. Some companies, such as Monsanto (St. Louis), claim to have managed to avoid producing any final wastes. The company's farm chemicals plant in Malaysia is one example - even the drums used to transport raw materials to the site have been replaced with returnable containers. Chiba (Basel) also has invested in cutting waste. The Swiss firm's dyestuffs plant at Candra Sari, Indonesia cut primary pollution by 90%, while product output rose 12% - a result of changing operations procedures and capital investment of only $6,500. A number of countries have started to address the industrial waste problem - foremost is Hong Kong, which is currently commissioning one of the first chemical waste treatment centers in the region. Other countries planning integrated waste treatment facilities include Indonesia, Malaysia, Australia, Thailand, Singapore, and China

Development of underwater laser cutting technology

International Nuclear Information System (INIS)

Sato, Seiichi; Inaba, Takanori; Inose, Koutarou; Matsumoto, Naoyuki; Sakakibara, Yuji

2015-01-01

In is desirable to use remote underwater device for the decommissioning work of highly radioactive components such as the nuclear internals from a view point of reducing the ranitidine exposure to the worker. Underwater laser cutting technology has advantages. First advantage in underwater laser cutting technology is that low reaction force during cutting, namely, remote operability is superior. Second point is that underwater laser cutting generates a little amount of secondary waste, because cutting kerf size is very small. Third point is that underwater laser cutting has low risk of the process delay, because device trouble is hard to happen. While underwater laser cutting has many advantages, the careful consideration in the safe treatment of the offgas which underwater laser cutting generates is necessary. This paper describes outline of underwater laser cutting technology developed by IHI Corporation (IHI) and that this technology is effective in various dismantling works in water. (author)

Design report for the interim waste containment facility at the Niagara Falls Storage Site

International Nuclear Information System (INIS)

1986-05-01

Low-level radioactive residues from pitchblende processing and thorium- and radium-contaminated sand, soil, and building rubble are presently stored at the Niagara Falls Storage Site (NFSS) in Lewiston, New York. These residues and wastes derive from past NFSS operations and from similar operations at other sites in the United States conducted during the 1940s by the Manhattan Engineer District (MED) and subsequently by the Atomic Energy Commission (AEC). The US Department of Energy (DOE), successor to MED/AEC, is conducting remedial action at the NFSS under two programs: on-site work under the Surplus Facilities Managemnt Program and off-site cleanup of vicinity properties under the Formerly Utilized Sites Remedial Action Program. On-site remedial action consists of consolidating the residues and wastes within a designated waste containment area and constructing a waste containment facility to prevent contaminant migration. The service life of the system is 25 to 50 years. Near-term remedial action construction activities will not jeopardize or preclude implementation of any other remedial action alternative at a later date. Should DOE decide to extend the service life of the system, the waste containment area would be upgraded to provide a minimum service life of 200 years. This report describes the design for the containment system. Pertinent information on site geology and hydrology and on regional seismicity and meteorology is also provided. Engineering calculations and validated computer modeling studies based on site-specific and conservative parameters confirm the adequacy of the design for its intended purposes of waste containment and environmental protection

Parametric Criticality Safety Calculations for Arrays of TRU Waste Containers

Energy Technology Data Exchange (ETDEWEB)

Gough, Sean T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-10-26

The Nuclear Criticality Safety Division (NCSD) has performed criticality safety calculations for finite and infinite arrays of transuranic (TRU) waste containers. The results of these analyses may be applied in any technical area onsite (e.g., TA-54, TA-55, etc.), as long as the assumptions herein are met. These calculations are designed to update the existing reference calculations for waste arrays documented in Reference 1, in order to meet current guidance on calculational methodology.

Differential lead retention in zircons: implications for nuclear waste containment.

Science.gov (United States)

Gentry, R V; Sworski, T J; McKown, H S; Smith, D H; Eby, R E; Christie, W H

1982-04-16

An innovative ultrasensitive technique was used for lead isotopic analysis of individual zircons extracted from granite core samples at depths of 960, 2170, 2900, 3930, and 4310 meters. The results show that lead, a relatively mobile element compared to the nuclear waste-related actinides uranium and thorium, has been highly retained at elevated temperatures (105 degrees to 313 degrees C) under conditions relevant to the burial of synthetic rock waste containers in deep granite holes.

Transuranic contaminated waste container characterization and data base. Revision I

International Nuclear Information System (INIS)

Kniazewycz, B.G.

1980-05-01

The Nuclear Regulatory Commission (NRC) is developing regulations governing the management, handling and disposal of transuranium (TRU) radioisotope contaminated wastes as part of the NRC's overall waste management program. In the development of such regulations, numerous subtasks have been identified which require completion before meaningful regulations can be proposed, their impact evaluated and the regulations implemented. This report was prepared to assist in the development of the technical data base necessary to support rule-making actions dealing with TRU-contaminated wastes. An earlier report presented the waste sources, characteristics and inventory of both Department of Energy (DOE) generated and commercially generated TRU waste. In this report a wide variety of waste sources as well as a large TRU inventory were identified. The purpose of this report is to identify the different packaging systems used and proposed for TRU waste and to document their characteristics. This document then serves as part of the data base necessary to complete preparation and initiate implementation of TRU waste container and packaging standards and criteria suitable for inclusion in the present TRU waste management program. It is the purpose of this report to serve as a working document which will be used as appropriate in the TRU Waste Management Program. This report, and those following, will be compatible not only in format, but also in reference material and direction

Hospital wastes management containing in radioactive refusals

International Nuclear Information System (INIS)

Campi, F.

1999-01-01

In large hospitals, featuring a nuclear medicine department, diagnostic examinations and metabolic therapies are performed using an amount of radio drugs per day averaging around some hundreds mCi. Part of these drugs are disposed in the conventional patient related waste and collected within the hospital itself. Before directing the wastes to the disposal, it is necessary verify that they do not contain radioactive materials. This article refers a study on the possibility to perform this verification by means of an automatic radio-metric system, in order to improve the efficiency, the speed and the safety of the control. Measures devoted to determined the minimum detectable activities for the main radionuclides used in the hospitals have been executed, and it has been designed a comprehensive device able to operate automatically, and unattended by any operator, the selection of radioactive refusals [it

In-situ containment and stabilization of buried waste

International Nuclear Information System (INIS)

Allan, M.L.; Kukacka, L.E.

1993-10-01

In FY 1993 research continued on development and testing of grout materials for in-situ containment and stabilization of buried waste. Specifically, the work was aimed at remediation of the Chemical Waste Landfill (CWL) at Sandia National Laboratories (SNL) in Albuquerque, New Mexico as part of the Mixed Waste Landfill Integrated Demonstration (MWLID). The work on grouting materials was initiated in FY 1992 and the accomplishments for that year are documented in the previous annual report (Allan, Kukacka and Heiser, 1992). The remediation plan involves stabilization of the chromium plume, placement of impermeable vertical and horizontal barriers to isolate the landfill and installation of a surface cap. The required depth of subsurface barriers is approximately 33 m (100 ft). The work concentrated on optimization of grout formulations for use as grout and soil cement barriers and caps. The durability of such materials was investigated, in addition to shrinkage cracking resistance, compressive and flexural strength and permeability. The potential for using fibers in grouts to control cracking was studied. Small scale field trials were conducted to test the practicality of using the identified formulations and to measure the long term performance. Large scale trials were conducted at Sandia as part of the Subsurface Barrier Emplacement Technology Program. Since it was already determined in FY 1992 that cementitious grouts could effectively stabilize the chromium plume at the CWL after pre-treatment is performed, the majority of the work was devoted to the containment aspect

Lead corrosion evaluation in high activity nuclear waste container (Argentina)

International Nuclear Information System (INIS)

Guasp, R.; Lanzani, L.; Bruzzoni, P.; Cufre, W.; Semino, C.J.

2000-01-01

This report describes a study of high activity nuclear waste canister corrosion in a deep geological disposal. In this canister design, the vitrified nuclear waste stainless steel container is shielded by a 100 mm thick lead wall. For mechanical resistance, the canister will also have a thin carbon steel external liner. Experimental and mathematical modeling studies are aimed to asses the corrosion kinetics of the carbon steel liner in first instance and then, once this liner has been corroded away, the corrosion kinetics of the main lead barrier. Being that oxygen reduction is the main cathodic reaction that supports the anodic oxidation of iron, a model is described predicting the rate of oxygen consumption in a sealed deep nuclear waste disposal vault as a result of the canister corrosion. Oxidation processes other than container corrosion, and that can account also for oxygen depletion, are not taken into consideration. Corrosion experimental studies on lead and its alloys in groundwater are also reported. These experiments are aimed to improve the corrosion resistance of commercial lead in groundwater. (author)

A batch assay to measure microbial hydrogen sulfide production from sulfur-containing solid wastes

Energy Technology Data Exchange (ETDEWEB)

Sun, Mei, E-mail: msun8@uncc.edu [Department of Civil, Construction, and Environmental Engineering, North Carolina State University, Campus Box 7908, Raleigh, NC (United States); Sun, Wenjie, E-mail: wsun@smu.edu [Department of Civil, Construction, and Environmental Engineering, North Carolina State University, Campus Box 7908, Raleigh, NC (United States); Department of Civil and Environmental Engineering, Southern Methodist University, PO Box 750340, Dallas, TX (United States); Barlaz, Morton A., E-mail: barlaz@ncsu.edu [Department of Civil, Construction, and Environmental Engineering, North Carolina State University, Campus Box 7908, Raleigh, NC (United States)

2016-05-01

Large volumes of sulfur-containing wastes enter municipal solid waste landfills each year. Under the anaerobic conditions that prevail in landfills, oxidized forms of sulfur, primarily sulfate, are converted to sulfide. Hydrogen sulfide (H{sub 2}S) is corrosive to landfill gas collection and treatment systems, and its presence in landfill gas often necessitates the installation of expensive removal systems. For landfill operators to understand the cost of managing sulfur-containing wastes, an estimate of the H{sub 2}S production potential is needed. The objective of this study was to develop and demonstrate a biochemical sulfide potential (BSP) test to measure the amount of H{sub 2}S produced by different types of sulfur-containing wastes in a relatively fast (30 days) and inexpensive (125 mL serum bottles) batch assay. This study confirmed the toxic effect of H{sub 2}S on both sulfate reduction and methane production in batch systems, and demonstrated that removing accumulated H{sub 2}S by base adsorption was effective for mitigating inhibition. H{sub 2}S production potentials of coal combustion fly ash, flue gas desulfurization residual, municipal solid waste combustion ash, and construction and demolition waste were determined in BSP assays. After 30 days of incubation, most of the sulfate in the wastes was converted to gaseous or aqueous phase sulfide, with BSPs ranging from 0.8 to 58.8 mL H{sub 2}S/g waste, depending on the chemical composition of the samples. Selected samples contained solid phase sulfide which contributed to the measured H{sub 2}S yield. A 60 day incubation in selected samples resulted in 39–86% additional sulfide production. H{sub 2}S production measured in BSP assays was compared with that measured in simulated landfill reactors and that calculated from chemical analyses. H{sub 2}S production in BSP assays and in reactors was lower than the stoichiometric values calculated from chemical composition for all wastes tested, demonstrating

Demonstration of close-coupled barriers for subsurface containment of buried waste

International Nuclear Information System (INIS)

Dwyer, B.P.; Heiser, J.; Stewart, W.

1996-01-01

The primary objective of this project is to develop and demonstrate a close-coupled barrier for the containment of subsurface waste or contaminant migration. A close-coupled barrier is produced by first installing a conventional cement grout curtain followed by a thin inner lining of a polymer grout. The resultant barrier is a cement polymer composite that has economic benefits derived from the cement and performance benefits from the durable and resistant polymer layer. Close-coupled barrier technology is applicable for final, interim, or emergency containment of subsurface waste forms. Consequently, when considering the diversity of technology application, the construction emplacement and material technology maturity, general site operational requirements, and regulatory compliance incentives, the close-coupled barrier system provides an alternative for any hazardous or mixed waste remediation plan. This paper discusses the installation of a close-coupled barrier and the subsequent integrity verification

Poisoning of bees with fluorine-containing industrial waste gases in Switzerland

Energy Technology Data Exchange (ETDEWEB)

Maurizio, A; Staub, M

1956-01-01

Mass poisoning of bees in the vicinity of Swiss Al factories was traced to high quantities of F in the waste gases. Plants and pollen in the vicinity contained 10-214 and 0.9-2.8 mg. % F resp., and collected rain water contained 0.1-10.4 mg. F/sg. dm. The dead bees each contained an av. of 15 ..gamma.. F.

Kinetin Reversal of NaCl Effects

Science.gov (United States)

Katz, Adriana; Dehan, Klara; Itai, Chanan

1978-01-01

Leaf discs of Nicotiana rustica L. were floated on NaCl in the presence of kinetin or abscisic acid. On the 5th day 14CO2 fixation, [3H]leucine incorporation, stomatal conductance, and chlorophyll content were determined. Kinetin either partially or completely reversed the inhibitory effects of NaCl while ABA had no effect. PMID:16660618

Effect of controlled potential on SCC of nuclear waste package container materials

International Nuclear Information System (INIS)

Lum, B. Y.; Roy, A. K.; Spragge, M. K.

1999-01-01

The slow-strain-rate (SSR) test technique was used to evaluate the susceptibility of Titanium (Ti) Gr-7 (UNS R52400) and Ti Gr-12 (UNS R53400) to stress corrosion cracking (SCC). Ti Gr-7 and Ti Gr-12 are two candidate container materials for the multi-barrier package for nuclear waste. The tests were done in a deaerated 90 C acidic brine (pH ∼ 2.7) containing 5 weight percent (wt%) sodium chloride (NaCl) using a strain rate of 3.3 x 10 -6 sec -1 . Before being tested in the acidic brine, specimens of each alloy were pulled inside the test chamber in the dry condition at ambient temperature. Then while in the test solution, specimens were strained under different cathodic (negative) controlled electrochemical potentials. These controlled potentials were selected based on the corrosion potential measured in the test solution before the specimens were strained. Results indicate that the times to failure (TTF) for Ti Gr-12 were much shorter than those for Ti Gr-7. Furthermore, as the applied potential became more cathodic, Ti Gr-12 showed reduced ductility in terms of percent reduction in area (%RA) and true fracture stress (σ f ). In addition, TTF and percent elongation (%El) reached the minimum values when Ti Gr-12 was tested under an impressed potential of -1162 mV. However, for Ti Gr-7, all these ductility parameters were not significantly influenced by the changes in applied potential. In general, the results of hydrogen analysis by secondary ion mass spectrometry (SIMS) showed increased hydrogen concentration at more cathodic controlled potentials. Optical microscopy and scanning electron microscopy (SEM) were used to evaluate the morphology of cracking both at the primary fracture face and the secondary cracks along the gage section of the broken tensile specimen. Transgranular secondary cracks were observed in both alloys possibly resulting from the formation of brittle titanium hydrides due to cathodic charging. The primary fracture face was characterized

Flexible process options for the immobilisation of residues and wastes containing plutonium

International Nuclear Information System (INIS)

Stewart, M.W.A.; Moricca, S.A.; Day, R. A.; Begg, B. D.; Scales, C. R.; Maddrell, E. R.; Eilbeck, A. B.

2007-01-01

Residues and waste streams containing plutonium present unique technical, safety, regulatory, security, and socio-political challenges. In the UK these streams range from lightly plutonium contaminated materials (PCM) through to residue s resulting directly from Pu processing operations. In addition there are potentially stocks of Pu oxide powders whose future designation may be either a waste or an asset, due to their levels of contamination making their reuse uneconomic, or to changes in nuclear policy. While waste management routes exist for PCM, an immobilisation process is required for streams containing higher levels of Pu. Such a process is being developed by Nexia Solutions and ANSTO to treat and immobilise Pu waste and residues currently stored on the Sellafield site. The characteristics of these Pu waste streams are highly variable. The physical form of the Pu waste ranges from liquids, sludges, powders/granules, to solid components (e.g., test fuels), with the Pu present as an ion in solution, as a salt, metal, oxide or other compound. The chemistry of the Pu waste streams also varies considerably with a variety of impurities present in many waste streams. Furthermore, with fissile isotopes present, criticality is an issue during operations and in the store or repository. Safeguards and security concerns must be assessed and controlled. The process under development, by using a combination of tailored waste form chemistry combined with flexible process technology aims to develop a process line to handle a broad range of Pu waste streams. It aims to be capable of dealing with not only current arisings but those anticipated to arise as a result of future operations or policy changes. (authors)

STABILIZATION OF A MIXED WASTE SLUDGE SURROGATE CONTAINING MORE THAN 260 PPM MERCURY

International Nuclear Information System (INIS)

Smith, W. J.; Feizollahi, F.; Brimley, R.

2002-01-01

In an earlier demonstration of an innovative mercury stabilization technology for the Department of Energy, ATG's full-scale process stabilized mercury in soils that initially contained more than 260 ppm of mercury of unknown speciation. The treated waste satisfied the leaching standards for mercury that qualify wastes containing less than 260 ppm for land disposal. This paper describes the extension of that work to demonstrate a full-scale process for the stabilization of a representative sludge that contained more than 260 ppm of Hg of several mercury species. RCRA (Resource Conservation and Recovery Act) regulations now require the recovery of mercury from any waste containing more than 260 ppm of mercury, usually with thermal retorts. The results of this work with a surrogate sludge, and of the previous work with an actual soil, support a proposal now before the U.S. EPA (Environmental Protection Agency) to allow such wastes to be stabilized without retorting. The full-scale demonstration with a sulfide reagent reduced the mercury concentrations in extracts of treated sludge below the relevant leaching standard, a Universal Treatment Standard (UTS) limit of 0.025 mg mercury per liter of leachate generated by the Toxicity Characteristic Leaching Procedure (TCLP). The sulfide formulation reduced the concentration to about onehalf the UTS limit

Corrosion of inconel in high-temperature borosilicate glass melts containing simulant nuclear waste

Science.gov (United States)

Mao, Xianhe; Yuan, Xiaoning; Brigden, Clive T.; Tao, Jun; Hyatt, Neil C.; Miekina, Michal

2017-10-01

The corrosion behaviors of Inconel 601 in the borosilicate glass (MW glass) containing 25 wt.% of simulant Magnox waste, and in ZnO, Mn2O3 and Fe2O3 modified Mg/Ca borosilicate glasses (MZMF and CZMF glasses) containing 15 wt.% of simulant POCO waste, were evaluated by dimensional changes, the formation of internal defects and changes in alloy composition near corrosion surfaces. In all three kinds of glass melts, Cr at the inconel surface forms a protective Cr2O3 scale between the metal surface and the glass, and alumina precipitates penetrate from the metal surface or formed in-situ. The corrosion depths of inconel 601 in MW waste glass melt are greater than those in the other two glass melts. In MW glass, the Cr2O3 layer between inconel and glass is fragmented because of the reaction between MgO and Cr2O3, which forms the crystal phase MgCr2O4. In MZMF and CZMF waste glasses the layers are continuous and a thin (Zn, Fe, Ni, B)-containing layer forms on the surface of the chromium oxide layer and prevents Cr2O3 from reacting with MgO or other constituents. MgCr2O4 was observed in the XRD analysis of the bulk MW waste glass after the corrosion test, and ZrSiO4 in the MZMF waste glass, and ZrSiO4 and CaMoO4 in the CZMF waste glass.

Electrochemical probing of high-level radioactive waste tanks containing washed sludge and precipitates

International Nuclear Information System (INIS)

Bickford, D.F.; Congdon, J.W.; Oblath, S.B.

1986-12-01

At the US Department of Energy's Savannah River Plant, corrosion of carbon steel storage tanks containing alkaline, high-level radioactive waste is controlled by specification of limits on waste composition and temperature. Processes for the preparation of waste for final disposal will result in waste with low corrosion inhibitor concentrations and, in some cases, high aromatic organic concentrations, neither of which are characteristic of previous operations. Laboratory tests, conducted to determine minimum corrosion inhibitor levels indicated pitting of carbon steel near the waterline for proposed storage conditions. In situ electrochemical measurements of full-scale radioactive process demonstrations have been conducted to assess the validity of laboratory tests. Probes included pH, Eh (potential relative to a standard hydrogen electrode), tank potential, and alloy coupons. In situ results are compared to those of the laboratory tests, with particular regard given to simulated solution composition. Transition metal hydroxide sludge contains strong passivating species for carbon steel. Washed precipitate contains organic species that lower solution pH and tend to reduce passivating films, requiring higher inhibitor concentrations than the 0.01 molar nitrite required for reactor fuel reprocessing wastes. Periodic agitation, to keep the organic phase suspended, or cathodic protection are possible alternatives to higher nitrite inhibitor concentrations

Combined Effects of Boron and NaCl on Wheat Seedlings

Directory of Open Access Journals (Sweden)

ZHEN Mei-nan

2015-08-01

Full Text Available To investigate the combined effects of boron(Band NaCl on the growth of wheat, a pot experiment was conducted using wheat (Triticum aestivum Linn.seedlings. Boron concentrations of culture medium were set as 0, 50 mg·kg-1 and 100 mg·kg-1, and NaCl concentrations were 0, 1 g·kg-1 and 2 g·kg-1. The results showed that both boron and NaCl could significantly inhibit wheat growth. At 50 mg B·kg-1, NaCl aggravated growth inhibition caused by boron. At 100 mg B·kg-1, however, NaCl alleviated the inhibition caused by boron. The combined stress of boron and NaCl significantly increased the root to shoot ratio of wheat. NaCl inhibited the uptake of boron by wheat. It suggests that under severe boron stress, NaCl is able to alleviate boron toxicity in wheat by increasing root to shoot ratio and reducing boron uptake.

Preliminary study for treatment methodology establishment of liquid waste containing uranium in refining facility lagoon

Energy Technology Data Exchange (ETDEWEB)

Lee, Byung Jik; Lee, Kune Woo; Won, Hui Jun; Ahn, Byung Gil; Shim, Joon Bo

1999-12-01

The preliminary study which establishes the treatment methodology of the sludge waste containing uranium in the conversion facility lagoon was performed. The property of lagoon liquid waste such as the initial water content, the density including radiochemical analysis results were obtained using the samples taken from the lagoon. The objective of this study is to provide some basically needed materials for selection of the most proper lagoon waste treatment methodology by reviewing the effective processes and methods for minimizing the secondary waste resulting from the treatment and disposition of large amount of radioactive liquid waste according to the facility closing. The lagoon waste can be classified into two sorts, such as supernatant and precipitate. The supernatants contain uranium less than 5 ppm and their water content are about 35 percent. Therefore, supernatants are solutions composed of mainly salt components. However, the precipitates have lots of uranium compound contained in the coagulation matrix, and are formed as two kinds of crystalline structures. The most proper method minimizing the secondary waste would be direct drying and solidification of the supernatants and precipitates after separation of them by filtering. (author)

Candidate container materials for Yucca Mountain waste package designs

International Nuclear Information System (INIS)

McCright, R.D.; Halsey, W.G.; Gdowski, G.E.; Clarke, W.L.

1991-09-01

Materials considered as candidates for fabricating nuclear waste containers are reviewed in the context of the Conceptual Design phase of a potential repository located at Yucca Mountain. A selection criteria has been written for evaluation of candidate materials for the next phase -- Advanced Conceptual Design. The selection criteria is based on the conceptual design of a thin-walled container fabricated from a single metal or alloy; the criteria consider the performance requirements on the container and the service environment in which the containers will be emplaced. A long list of candidate materials is evaluated against the criteria, and a short list of materials is proposed for advanced characterization in the next design phase

Survey of degradation modes of candidate materials for high-level radioactive-waste disposal containers

International Nuclear Information System (INIS)

Bullen, D.B.; Gdowski, G.E.; Weiss, H.

1988-06-01

Three copper-based alloys, CDA 102 (oxygen-free copper), CDA 613 (Cu-7Al), and CDA 715 (Cu-30Ni), are being considered along with three austenitic candidates as possible materials for fabrication of containers for disposal of high-level radioactive waste. The waste will include spent fuel assemblies from reactors as well as high-level reprocessing wastes in borosilicate glass and will be sent to the prospective repository at Yucca Mountain, Nevada, for disposal. The containers must maintain mechanical integrity for 50 yr after emplacement to allow for retrieval of waste during the preclosure phase of repository operation. Containment is required to be substantially complete for up to 300 to 1000 yr. During the early period, the containers will be exposed to high temperatures and high gamma radiation fields from the decay of high-level waste. The final closure joint will be critical to the integrity of the containers. This volume surveys the available data on the metallurgy of the copper-based candidate alloys and the welding techniques employed to join these materials. The focus of this volume is on the methods applicable to remote-handling procedures in a hot-cell environment with limited possibility of postweld heat treatment. The three copper-based candidates are ranked on the basis of the various closure techniques. On the basis of considerations regarding welding, the following ranking is proposed for the copper-based alloys: CDA 715 (best) > CDA 102 > CDA 613 (worst). 49 refs., 15 figs., 1 tab

The TN-GEMINI: experience on a versatile alpha waste transport container

International Nuclear Information System (INIS)

Roland, V.; Chanzy, Y.

2001-01-01

The present paper discusses experience gained in moving alpha wastes and its teachings regarding transport aspects of D and D. Alpha wastes are generated in fuel cycle facilities such as those involved in reprocessing, in manufacture of mixed oxide fuel, and by research laboratories. If a significant amount of wastes has to be transported, then a Type B packaging is required. Developed by Transnucleaire and COGEMA, the TN GEMINI container enables nuclear facilities operators to optimise their alpha waste transport management, and more generally contribute to their D and D projects. After describing succinctly the design of the TN GEMINI, the paper will explain how the packaging is being operated. Teachings from experience will be shared. (orig.)

Stability and Volumetric Properties of Asphalt Mixture Containing Waste Plastic

Directory of Open Access Journals (Sweden)

Abd Kader Siti Aminah

2017-01-01

Full Text Available The objectives of this study are to determine the optimum bitumen content (OBC for every percentage added of waste plastics in asphalt mixtures and to investigate the stability properties of the asphalt mixtures containing waste plastic. Marshall stability and flow values along with density, air voids in total mix, voids in mineral aggregate, and voids filled with bitumen were determined to obtain OBC at different percentages of waste plastic, i.e., 4%, 6%, 8%, and 10% by weight of bitumen as additive. Results showed that the OBC for the plastic-modified asphalt mixtures at 4%, 6%, 8%, and 10% are 4.98, 5.44, 5.48, and 5.14, respectively. On the other hand, the controlled specimen’s shows better volumetric properties compared to plastic mixes. However, 4% additional of waste plastic indicated better stability than controlled specimen.

Evolution of thermoelectric performance for (Bi,Sb)2Te3 alloys from cutting waste powders to bulks with high figure of merit

Science.gov (United States)

Fan, Xi‧an; Cai, Xin zhi; Han, Xue wu; Zhang, Cheng cheng; Rong, Zhen zhou; Yang, Fan; Li, Guang qiang

2016-01-01

Bi2Te3 based cutting waste powders from cutting wafers were firstly selected as raw materials to prepare p-type Bi2Te3 based thermoelectric (TE) materials. Through washing, reducing, composition correction, smelting and resistance pressing sintering (RPS) process, p-type (Bi,Sb)2Te3 alloy bulks with different nominal stoichiometries were successfully obtained. The evolution of microstructure and TE performance for (Bi,Sb)2Te3 alloys were investigated in detail. All evidences confirmed that most of contaminants from line cutting process such as cutting fluid and oxides of Bi, Sb or Te could be removed by washing, reducing and smelting process used in this work. The carrier content and corresponding TE properties could be adjusted effectively by appropriate composition correction treatment. At lastly, a bulk with a nominal stoichiometry of Bi0.44Sb1.56Te3 was obtained and its' dimensionless figure of merit (ZT) was about 1.16 at 90 °C. The ZT values of Bi0.36Sb1.64Te3 and Bi0.4Sb1.6Te3 alloy bulks could also reach 0.98 and 1.08, respectively. Different from the conventional recycling technology such as hydrometallurgy extraction methods, the separation and extraction of beneficial elements such as Bi, Sb and Te did not need to be performed and the Bi2Te3 based bulks with high TE properties could be directly obtained from the cutting waste powders. In addition, the recycling technology introduced here was green and more suitable for practical industrial application. It can improve material utilization and lower raw material costs of manufacturers.

Waste collection in developing countries - Tackling occupational safety and health hazards at their source

Energy Technology Data Exchange (ETDEWEB)

Bleck, Daniela, E-mail: bleck.daniela@baua.bund.de [Federal Institute for Occupational Safety and Health, Germany (BAuA), Friedrich Henkel Weg 1-25, 44149 Dortmund (Germany); Wettberg, Wieland, E-mail: wettberg.wieland@baua.bund.de [Federal Institute for Occupational Safety and Health, Germany (BAuA), Friedrich Henkel Weg 1-25, 44149 Dortmund (Germany)

2012-11-15

Waste management procedures in developing countries are associated with occupational safety and health risks. Gastro-intestinal infections, respiratory and skin diseases as well as muscular-skeletal problems and cutting injuries are commonly found among waste workers around the globe. In order to find efficient, sustainable solutions to reduce occupational risks of waste workers, a methodological risk assessment has to be performed and counteractive measures have to be developed according to an internationally acknowledged hierarchy. From a case study in Addis Ababa, Ethiopia suggestions for the transferral of collected household waste into roadside containers are given. With construction of ramps to dump collected household waste straight into roadside containers and an adaptation of pushcarts and collection procedures, the risk is tackled at the source.

The conceptual design of waste repository for radioactive waste from medical, industrial and research facilities containing comparatively high radioactivity

International Nuclear Information System (INIS)

Yamamoto, Masayuki; Hashimoto, Naro

2002-02-01

Advisory Committee on Nuclear Fuel Cycle Backend Policy reported the basic approach to the RI and Institute etc. wastes on March 2002. According to it, radioactive waste form medical, industrial and research facilities should be classified by their radioactivity properties and physical and chemical properties, and should be disposed in the appropriate types of repository with that classification. For the radioactive waste containing comparatively high radioactivity generated from reactors, NSC has established the Concentration limit for disposal. NSC is now discussing about the limit for the radioactive waste from medical, industrial and research facilities containing comparatively high radioactivity. Japan Nuclear Cycle Development Institute (JNC) preliminary studied about the repository for radioactive waste from medical, industrial and research facilities and discussed about the problems for design on H12. This study was started to consider those problems, and to develop the conceptual design of the repository for radioactive waste from medical, industrial and research facilities. Safety assessment for that repository is also performed. The result of this study showed that radioactive waste from medical, industrial and research facilities of high activity should be disposed in the repository that has higher performance of barrier system comparing with the vault type near surface facility. If the conditions of the natural barrier and the engineering barrier are clearer, optimization of the design will be possible. (author)

Experiences in the emptying of waste silos containing solid nuclear waste from graphite- moderated reactors

International Nuclear Information System (INIS)

Wall, S.; Schwarz, T.

2003-01-01

Before reactor sites can be handed over for ultimate decommissioning, at some sites silos containing waste from operations need to be emptied. The form and physical condition of the waste demands sophisticated retrieval technologies taking into account the onsite situation in terms of infrastructure and silo geometry. Furthermore, in the case of graphite moderated reactors, this waste usually includes several tonnes of graphite waste requiring special HVAC and dust handling measures. RWE NUKEM Group has already performed several contracts dealing with such emptying tasks. Of particular interest for the upcoming decommissioning projects in France might be the activities at Vandellos, Spain and Trawsfynnyd, UK. Retrieval System for Vandellos NPP is discussed. Following an international competitive tender exercise, RWE NUKEM won the contract to provide a turn-key retrieval system. This involved the design, manufacture and installation of a system built around the modules of a 200 kg capacity version of the ARTISAN manipulator system. The ARTISAN 200 manipulator, with remote slave arm detach facility, was deployed on a telescopic mast inserted into the silos through the roof penetrations. The manipulator deployed a range of tools to gather the waste and load it into a transfer basket, deployed through an adjacent penetration. After commissioning, the system cleared the vaults in less than the scheduled period with no failures. At the Trawsfynnyd Magnox plants two types of intermediate level waste (ILW) accumulated on site; namely Miscellaneous Activated Components (MAC) and Fuel Element Debris (FED). MAC is predominantly components that have been activated by the reactor core and then discharged. FED mainly consists of fuel cladding produced when fuel elements were prepared for dispatch to the reprocessing facility. RWE NUKEM Ltd. was awarded a contract to design, supply, commission and operate equipment to retrieve, pack and immobilize the two waste streams. Major

Discharge of water containing waste emanating from land to the ...

African Journals Online (AJOL)

containing waste (wastewater), which emanates from land-based sources and which directly impact on the marine environment. These sources include sea outfalls, storm water drains, canals, rivers and diffuse sources of pollution. To date ...

DEMONSTRATiON OF A SUBSURFACE CONTAINMENT SYSTEM FOR INSTALLATION AT DOE WASTE SITES

Energy Technology Data Exchange (ETDEWEB)

Thomas J. Crocker; Verna M. Carpenter

2003-05-21

Between 1952 and 1970, DOE buried mixed waste in pits and trenches that now have special cleanup needs. The disposal practices used decades ago left these landfills and other trenches, pits, and disposal sites filled with three million cubic meters of buried waste. This waste is becoming harmful to human safety and health. Today's cleanup and waste removal is time-consuming and expensive with some sites scheduled to complete cleanup by 2006 or later. An interim solution to the DOE buried waste problem is to encapsulate and hydraulically isolate the waste with a geomembrane barrier and monitor the performance of the barrier over its 50-yr lifetime. The installed containment barriers would isolate the buried waste and protect groundwater from pollutants until final remediations are completed. The DOE has awarded a contract to RAHCO International, Inc.; of Spokane, Washington; to design, develop, and test a novel subsurface barrier installation system, referred to as a Subsurface Containment System (SCS). The installed containment barrier consists of commercially available geomembrane materials that isolates the underground waste, similar to the way a swimming pools hold water, without disrupting hazardous material that was buried decades ago. The barrier protects soil and groundwater from contamination and effectively meets environmental cleanup standards while reducing risks, schedules, and costs. Constructing the subsurface containment barrier uses a combination of conventional and specialized equipment and a unique continuous construction process. This innovative equipment and construction method can construct a 1000-ft-long X 34-ft-wide X 30-ft-deep barrier at construction rates to 12 Wday (8 hr/day operation). Life cycle costs including RCRA cover and long-term monitoring range from approximately $380 to $590/cu yd of waste contained or $100 to $160/sq ft of placed barrier based upon the subsurface geology surrounding the waste. Project objectives for Phase

Demonstration of close-coupled barriers for subsurface containment of buried waste

International Nuclear Information System (INIS)

Heiser, J.; Dwyer, B.

1995-01-01

The primary objective of this project is to develop and demonstrate a close-coupled barrier for the containment of subsurface waste or contaminant migration. A close-coupled barrier is produced by first installing a conventional cement grout curtain followed by a thin lining of a polymer grout. The resultant barrier is a cement polymer composite that has economic benefits derived from the cement and performance benefits from the durable and resistant polymer layer. Close-coupled barrier technology is applicable for final, interim, or emergency containment of subsurface waste forms. Consequently, when considering the diversity of technology application, the construction emplacement and material technology maturity, general site operational requirements, and regulatory compliance incentives, the close-coupled barrier system provides an alternative for any hazardous or mixed waste remediation plan. This paper will discuss the installation of a close-coupled barrier and the subsequent integrity verification. The demonstration will take place at a cold site at the Hanford Geotechnical Test Facility, 400 Area, Hanford, Washington

In situ testing of titanium and mild steel nuclear waste containers at the WIPP site

International Nuclear Information System (INIS)

Molecke, M.A.

1990-01-01

An overview of the Waste Isolation Pilot Plant (WIPP) in situ tests on the corrosion of titanium and mild steel for high level waste containers is presented. The tests at Sandia have moved out of the laboratory into a test underground facility in order to evaluate the performance of the waste package material. The tests are being performed under both near-reference and accelerated salt repository conditions. Some containers are filled with high level waste glass (non-radioactive); others contain electric heaters. Backfill material is either bentonite/sand or crushed salt. In other tests metals and glasses are exposed directly to brine. The tests are designed to study the corrosion and metallurgy of the canister and overpack materials; the feasibility and performance of backfill materials; and near-field effects such as brine migration

Electron scattering in graphene with adsorbed NaCl nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Drabińska, Aneta, E-mail: Aneta.Drabinska@fuw.edu.pl; Kaźmierczak, Piotr; Bożek, Rafał; Karpierz, Ewelina; Wysmołek, Andrzej; Kamińska, Maria [Faculty of Physics, University of Warsaw, Pasteura 5, 02-093 Warsaw (Poland); Wołoś, Agnieszka [Faculty of Physics, University of Warsaw, Pasteura 5, 02-093 Warsaw (Poland); Institute of Physics, Polish Academy of Sciences, Al. Lotników 32/46, 02-668 Warsaw (Poland); Pasternak, Iwona; Strupiński, Włodek [Institute of Electronic Materials Technology, Wólczyńska 133, 01-919 Warsaw (Poland); Krajewska, Aleksandra [Institute of Electronic Materials Technology, Wólczyńska 133, 01-919 Warsaw (Poland); Institute of Optoelectronics, Military University of Technology, Kaliskiego 2, 00-908 Warsaw (Poland)

2015-01-07

In this work, the results of contactless magnetoconductance and Raman spectroscopy measurements performed for a graphene sample after its immersion in NaCl solution were presented. The properties of the immersed sample were compared with those of a non-immersed reference sample. Atomic force microscopy and electron spin resonance experiments confirmed the deposition of NaCl nanoparticles on the graphene surface. A weak localization signal observed using contactless magnetoconductance showed the reduction of the coherence length after NaCl treatment of graphene. Temperature dependence of the coherence length indicated a change from ballistic to diffusive regime in electron transport after NaCl treatment. The main inelastic scattering process was of the electron-electron type but the major reason for the reduction of the coherence length at low temperatures was additional, temperature independent, inelastic scattering. We associate it with spin flip scattering, caused by NaCl nanoparticles present on the graphene surface. Raman spectroscopy showed an increase in the D and D′ bands intensities for graphene after its immersion in NaCl solution. An analysis of the D, D′, and G bands intensities proved that this additional scattering is related to the decoration of vacancies and grain boundaries with NaCl nanoparticles, as well as generation of new on-site defects as a result of the decoration of the graphene surface with NaCl nanoparticles. The observed energy shifts of 2D and G bands indicated that NaCl deposition on the graphene surface did not change carrier concentration, but reduced compressive biaxial strain in the graphene layer.

Electron scattering in graphene with adsorbed NaCl nanoparticles

International Nuclear Information System (INIS)

Drabińska, Aneta; Kaźmierczak, Piotr; Bożek, Rafał; Karpierz, Ewelina; Wysmołek, Andrzej; Kamińska, Maria; Wołoś, Agnieszka; Pasternak, Iwona; Strupiński, Włodek; Krajewska, Aleksandra

2015-01-01

In this work, the results of contactless magnetoconductance and Raman spectroscopy measurements performed for a graphene sample after its immersion in NaCl solution were presented. The properties of the immersed sample were compared with those of a non-immersed reference sample. Atomic force microscopy and electron spin resonance experiments confirmed the deposition of NaCl nanoparticles on the graphene surface. A weak localization signal observed using contactless magnetoconductance showed the reduction of the coherence length after NaCl treatment of graphene. Temperature dependence of the coherence length indicated a change from ballistic to diffusive regime in electron transport after NaCl treatment. The main inelastic scattering process was of the electron-electron type but the major reason for the reduction of the coherence length at low temperatures was additional, temperature independent, inelastic scattering. We associate it with spin flip scattering, caused by NaCl nanoparticles present on the graphene surface. Raman spectroscopy showed an increase in the D and D′ bands intensities for graphene after its immersion in NaCl solution. An analysis of the D, D′, and G bands intensities proved that this additional scattering is related to the decoration of vacancies and grain boundaries with NaCl nanoparticles, as well as generation of new on-site defects as a result of the decoration of the graphene surface with NaCl nanoparticles. The observed energy shifts of 2D and G bands indicated that NaCl deposition on the graphene surface did not change carrier concentration, but reduced compressive biaxial strain in the graphene layer

Position for determining gas-phase volatile organic compound concentrations in transuranic waste containers. Revision 2

Energy Technology Data Exchange (ETDEWEB)

Connolly, M.J.; Liekhus, K.J. [Lockheed Martin Idaho Technologies Co., Idaho Falls, ID (United States). Idaho National Engineering and Environmental Lab.; Djordjevic, S.M.; Loehr, C.A.; Spangler, L.R. [Benchmark Environmental Corp. (United States)

1998-06-01

In the conditional no-migration determination (NMD) for the test phase of the Waste Isolation Pilot Plant (WIPP), the US Environmental Protection Agency (EPA) imposed certain conditions on the US Department of Energy (DOE) regarding gas phase volatile organic compound (VOC) concentrations in the void space of transuranic (TRU) waste containers. Specifically, the EPA required the DOE to ensure that each waste container has no layer of confinement that contains flammable mixtures of gases or mixtures of gases that could become flammable when mixed with air. The EPA also required that sampling of the headspace of waste containers outside inner layers of confinement be representative of the entire void space of the container. The EPA stated that all layers of confinement in a container would have to be sampled until DOE can demonstrate to the EPA that sampling of all layers is either unnecessary or can be safely reduced. A test program was conducted at the Idaho National Engineering and Environmental Laboratory (INEEL) to demonstrate that the gas phase VOC concentration in the void space of each layer of confinement in vented drums can be estimated from measured drum headspace using a theoretical transport model and that sampling of each layer of confinement is unnecessary. This report summarizes the studies performed in the INEEL test program and extends them for the purpose of developing a methodology for determining gas phase VOC concentrations in both vented and unvented TRU waste containers. The methodology specifies conditions under which waste drum headspace gases can be said to be representative of drum gases as a whole and describes a method for predicting drum concentrations in situations where the headspace concentration is not representative. The methodology addresses the approach for determining the drum VOC gas content for two purposes: operational period drum handling and operational period no-migration calculations.

Position for determining gas phase volatile organic compound concentrations in transuranic waste containers. Revision 1

International Nuclear Information System (INIS)

Connolly, M.J.; Liekhus, K.J.; Djordjevic, S.M.; Loehr, C.A.; Spangler, L.R.

1995-08-01

In the conditional no-migration determination (NMD) for the test phase of the Waste Isolation Pilot Plant (WIPP), the US Environmental Protection Agency (EPA) imposed certain conditions on the US Department of Energy (DOE) regarding gas phase volatile organic compound (VOC) concentrations in the void space of transuranic (TRU) waste containers. Specifically, the EPA required the DOE to ensure that each waste container has no layer of confinement that contains flammable mixtures of gases or mixtures of gases that could become flammable when mixed with air. The EPA also required that sampling of the headspace of waste containers outside inner layers of confinement be representative of the entire void space of the container. The EPA stated that all layers of confinement in a container would have to be sampled until DOE can demonstrate to the EPA that sampling of all layers is either unnecessary or can be safely reduced. A test program was conducted at the Idaho National Engineering Laboratory (INEL) to demonstrate that the gas phase VOC concentration in the void space of each layer of confinement in vented drums can be estimated from measured drum headspace using a theoretical transport model and that sampling of each layer of confinement is unnecessary. This report summarizes the studies performed in the INEL test program and extends them for the purpose of developing a methodology for determining gas phase VOC concentrations in both vented and unvented TRU waste containers. The methodology specifies conditions under which waste drum headspace gases can be said to be representative of drum gases as a whole and describes a method for predicting drum concentrations in situations where the headspace concentration is not representative. The methodology addresses the approach for determining the drum VOC gas content for two purposes: operational period drum handling and operational period no-migration calculations

Position for determining gas-phase volatile organic compound concentrations in transuranic waste containers. Revision 2

International Nuclear Information System (INIS)

Connolly, M.J.; Liekhus, K.J.

1998-06-01

In the conditional no-migration determination (NMD) for the test phase of the Waste Isolation Pilot Plant (WIPP), the US Environmental Protection Agency (EPA) imposed certain conditions on the US Department of Energy (DOE) regarding gas phase volatile organic compound (VOC) concentrations in the void space of transuranic (TRU) waste containers. Specifically, the EPA required the DOE to ensure that each waste container has no layer of confinement that contains flammable mixtures of gases or mixtures of gases that could become flammable when mixed with air. The EPA also required that sampling of the headspace of waste containers outside inner layers of confinement be representative of the entire void space of the container. The EPA stated that all layers of confinement in a container would have to be sampled until DOE can demonstrate to the EPA that sampling of all layers is either unnecessary or can be safely reduced. A test program was conducted at the Idaho National Engineering and Environmental Laboratory (INEEL) to demonstrate that the gas phase VOC concentration in the void space of each layer of confinement in vented drums can be estimated from measured drum headspace using a theoretical transport model and that sampling of each layer of confinement is unnecessary. This report summarizes the studies performed in the INEEL test program and extends them for the purpose of developing a methodology for determining gas phase VOC concentrations in both vented and unvented TRU waste containers. The methodology specifies conditions under which waste drum headspace gases can be said to be representative of drum gases as a whole and describes a method for predicting drum concentrations in situations where the headspace concentration is not representative. The methodology addresses the approach for determining the drum VOC gas content for two purposes: operational period drum handling and operational period no-migration calculations

Technical considerations for evaluating substantially complete containment of high-level waste within the waste package

Energy Technology Data Exchange (ETDEWEB)

Manaktala, H.K. (Southwest Research Inst., San Antonio, TX (USA). Center for Nuclear Waste Regulatory Analyses); Interrante, C.G. (Nuclear Regulatory Commission, Washington, DC (USA). Div. of High-Level Waste Management)

1990-12-01

This report deals with technical information that is considered essential for demonstrating the ability of the high-level radioactive waste package to provide substantially complete containment'' of its contents (vitrified waste form or spent light-water reactor fuel) for a period of 300 to 1000 years in a geological repository environment. The discussion is centered around technical considerations of the repository environment, materials and fabrication processes for the waste package components, various degradation modes of the materials of construction of the waste packages, and inspection and monitoring of the waste package during the preclosure and retrievability period, which could begin up to 50 years after initiation of waste emplacement. The emphasis in this report is on metallic materials. However, brief references have been made to other materials such as ceramics, graphite, bonded ceramic-metal systems, and other types of composites. The content of this report was presented to an external peer review panel of nine members at a workshop held at the Center for Nuclear Waste Regulatory Analyses (CNWRA), Southwest Research Institute, San Antonio, Texas, April 2--4, 1990. The recommendations of the peer review panel have been incorporated in this report. There are two companion reports; the second report in the series provides state-of-the-art techniques for uncertainty evaluations. 97 refs., 1 fig.

Technical considerations for evaluating substantially complete containment of high-level waste within the waste package

International Nuclear Information System (INIS)

Manaktala, H.K.; Interrante, C.G.

1990-12-01

This report deals with technical information that is considered essential for demonstrating the ability of the high-level radioactive waste package to provide ''substantially complete containment'' of its contents (vitrified waste form or spent light-water reactor fuel) for a period of 300 to 1000 years in a geological repository environment. The discussion is centered around technical considerations of the repository environment, materials and fabrication processes for the waste package components, various degradation modes of the materials of construction of the waste packages, and inspection and monitoring of the waste package during the preclosure and retrievability period, which could begin up to 50 years after initiation of waste emplacement. The emphasis in this report is on metallic materials. However, brief references have been made to other materials such as ceramics, graphite, bonded ceramic-metal systems, and other types of composites. The content of this report was presented to an external peer review panel of nine members at a workshop held at the Center for Nuclear Waste Regulatory Analyses (CNWRA), Southwest Research Institute, San Antonio, Texas, April 2--4, 1990. The recommendations of the peer review panel have been incorporated in this report. There are two companion reports; the second report in the series provides state-of-the-art techniques for uncertainty evaluations. 97 refs., 1 fig

Buckling design criteria for waste package disposal containers in mined salt repositories: Technical report

International Nuclear Information System (INIS)

Mallett, R.H.

1986-12-01

This report documents analytical and experimental results from a survey of the technical literature on buckling of thick-walled cylinders under external pressure. Based upon these results, a load factor is suggested for the design of waste package containers for disposal of high-level radioactive waste in repositories mined in salt formations. The load factor is defined as a ratio of buckling pressure to allowable pressure. Specifically, a load factor which ranges from 1.5 for plastic buckling to 3.0 for elastic buckling is included in a set of proposed buckling design criteria for waste disposal containers. Formulas are given for buckling design under axisymmetric conditions. Guidelines are given for detailed inelastic buckling analyses which are generally required for design of disposal containers

Secretory NaCl and volume flow in renal tubules.

Science.gov (United States)

Beyenbach, K W

1986-05-01

This review attempts to give a retrospective survey of the available evidence concerning the secretion of NaCl and fluid in renal tubules of the vertebrate kidney. In the absence of glomerular filtration, epithelial secretory mechanisms, which to this date have not been elucidated, are responsible for the renal excretion of NaCl and water in aglomerular fish. However, proximal tubules isolated from glomerular fish kidneys of the flounder, killifish, and the shark also have the capacity to secrete NaCl and fluid. In shark proximal tubules, fluid secretion appears to be driven via secondary active transport of Cl. In another marine vertebrate, the sea snake, secretion of Na (presumably NaCl) and fluid is observed in freshwater-adapted and water-loaded animals. Proximal tubules of mammals can be made to secrete NaCl in vitro together with secretion of aryl acids. An epithelial cell line derived from dog kidney exhibits secondary active secretion of Cl when stimulated with catecholamines. Tubular secretion of NaCl and fluid may serve a variety of renal functions, all of which are considered here. The occurrence of NaCl and fluid secretion in glomerular proximal tubules of teleosts, elasmobranchs, and reptiles and in mammalian renal tissue cultures suggests that the genetic potential for NaCl secretion is present in every vertebrate kidney.

Laser-induced breakdown spectroscopy for the real-time analysis of mixed waste samples containing Sr

International Nuclear Information System (INIS)

Barefield, J.E. II; Koskelo, A.C.; Multari, R.A.; Cremers, D.A.; Gamble, T.K.; Han, C.Y.

1995-01-01

In this report, the use of Laser-induced breakdown spectroscopy to analyze mixed waste samples containing Sr is discussed. The mixed waste samples investigated include vitrified waste glass and contaminated soil. Compared to traditional analysis techniques, the laser-based method is fast (i.e., analysis times on the order of minutes) and essentially waste free since little or no sample preparation is required. Detection limits on the order of pmm Sr were determined. Detection limits obtained using a fiber optic cable to deliver laser pulses to soil samples containing Cr, Zr, Pb, Be, Cu, and Ni will also be discussed

The Effects of IBA and NAA, and Rooting Media on Propagation of Miniature Rose Cuttings (Rosa hybrida

Directory of Open Access Journals (Sweden)

azam ranjbar

2017-09-01

miniature rose stem cutting, this research was carried out as a factorial on the basis of randomized complete design (RCD with three replications. Plant growth regulators including IBA at concentrations of 0, 1000, 2000 and 3000 mgl-1, concentrations of NAA at 0, 500, 1000, 1500 and 2000 mgl-1 were applied together with two types of rooting media. Media including mixing volume of perlite, tea waste compost and sand in a ratio of 1: 2: 2, and perlite, peat and sand in a ratio of 1:2:2 were mixed and applied in this experiment. Using SAS software, data was analyzed based on a generalized linear model (GLM analysis and tested by least significant difference (LSD at (P-value< 0.05. Results and Discussion: Results showed that the highest rooting percentage of cuttings was obtained with 2000 mgl-1 of IBA, while no significant effect of NAA treatment and different rooting media on percentage of rooting was revealed. The two-fold and three-fold interaction of treatments on other measured traits such as primary and secondary root number and root diameter were significant. The two-fold interaction of NAA treatments and rooting media on the trait of primary root number were no significant. The highest root number and root diameter measured in medium containing perlite, tea waste compost and sand in a ratio of 1:2:2 for cutting received combined plant growth regulators. Conclusions: Compost, the final product of organic residues degradation, improves soil physical characteristics such as soil aggregate formation and stability, water penetration, porosity, compressing resistance and nutrients availability. As well, it improves soil biological characteristics and in result, integration of compost with soil can increase growth, yield and quality of crop. There are also some evidences that in contrast of peat, compost contains plant growth regulators improved plant growth and development. Totally, considering our obtained results, in order to accelerate rooting formation in miniature rose

Model for analyzing demand for low-level waste transport containers - regionalized and non-regionalized scenarios

International Nuclear Information System (INIS)

Nelson, A.J.; Rose, K.

1982-01-01

Certain types of low-level radioactive waste (LLW) must be shipped in expensive special containers. It is therefore desirable to keep container utilization high. There must be a stock of containers sufficient to ship waste in a timely fashion, but one does not want to have containers sitting idle a significant fraction of the time. A computerized discrete event network model has been developed and is described in this report. The model allows an analyst to determine the effects of varying the increase in LLW, establishment of regional disposal, etc. on requirements for shipping containers

Hazardous waste dislodging and conveyance: The confined sluicing method

International Nuclear Information System (INIS)

Summers, D.A.; Fossey, R.D.; Mann, M.D.; Blaine, J.G.

1994-09-01

This report describes an investigation of a means for dislodging and conveying waste currently stored in underground storage tanks. A series of experiments have been carried out to evaluate the potential of a medium pressure, medium flow rate cutting system as a means of dislodging the waste. It has been found that waterjets at a pressure of 10,000 psi can effectively cut the material which has been chosen to simulate the hardened saltcake within the storage tanks. Based on a parameterization test it has thus been calculated that an inlet flow volume of approximately 30 gallons per minute will be sufficient to excavate 30 gallons per minute of waste from a tank. In order to transport the resulting slurry from the tank, a modified jet pump has been developed and has demonstrated its capability of conveying fluid and waste particles, up to one inch in diameter, to a height of more than 60 feet. Experiments were conducted to examine different configurations to achieve the production levels required for waste removal and to clean the walls of residual material. It was found more effective to clean the walls using an inclined angle of impact rather than a perpendicular angle of impact in order to provide a safeguard against driving the water through any cracks in the containment. It was demonstrated that excavation can take place with almost total immediate extraction of the water and debris from the cutting process. The results have qualitatively shown the potential of a medium pressure waterjet system for achieving the required results for underground storage tank waste retrieval

Radionuclide transport through perforations in nuclear waste containers

International Nuclear Information System (INIS)

Aidun, C.K.; Bloom, S.G.; Raines, G.E.

1987-11-01

Previous analytical models for the steady-state radionuclide release rate through perforations in nuclear waste containers into the surrounding medium are based on a zero wall thickness assumption. In this paper we investigate the effect of the wall thickness on the mass transfer rate through isolated cylindrical holes. We solve the steady-state diffusion equation for the concentration field and derive a model based on the analytical solution. By direct comparison, we show that the zero wall thickness model overpredicts the mass transfer rate by about 1300 percent for a circular hole with 1-cm radius and a wall thickness of 10 cm. As expected, the zero-thickness model becomes even less accurate as the hole radius decreases; it predicts a greater release rate from a large number of small holes than the mass transfer rate from an uncontained waste form cylinder. In contrast, the results predicted by our model remain bounded for isolated holes and never exceed the mass transfer from an uncontained waste form. 6 refs., 9 figs., 3 tabs

Treatment technology analysis for mixed waste containers and debris

International Nuclear Information System (INIS)

Gehrke, R.J.; Brown, C.H.; Langton, C.A.; Askew, N.M.; Kan, T.; Schwinkendorf, W.E.

1994-03-01

A team was assembled to develop technology needs and strategies for treatment of mixed waste debris and empty containers in the Department of Energy (DOE) complex, and to determine the advantages and disadvantages of applying the Debris and Empty Container Rules to these wastes. These rules issued by the Environmental Protection Agency (EPA) apply only to the hazardous component of mixed debris. Hazardous debris that is subjected to regulations under the Atomic Energy Act because of its radioactivity (i.e., mixed debris) is also subject to the debris treatment standards. The issue of treating debris per the Resource Conservation and Recovery Act (RCRA) at the same time or in conjunction with decontamination of the radioactive contamination was also addressed. Resolution of this issue requires policy development by DOE Headquarters of de minimis concentrations for radioactivity and release of material to Subtitle D landfills or into the commercial sector. The task team recommends that, since alternate treatment technologies (for the hazardous component) are Best Demonstrated Available Technology (BDAT): (1) funding should focus on demonstration, testing, and evaluation of BDAT on mixed debris, (2) funding should also consider verification of alternative treatments for the decontamination of radioactive debris, and (3) DOE should establish criteria for the recycle/reuse or disposal of treated and decontaminated mixed debris as municipal waste

Microwave assisted leaching and electrochemical recovery of copper from printed circuit boards of computer waste

Science.gov (United States)

Ivǎnuş, R. C.; ǎnuş, D., IV; Cǎlmuc, F.

2010-06-01

Due to the rapid technological progress, the replacement of electronic equipment is very often necessary, leading to huge amounts that end up as waste. In addition, waste electrical and electronic equipment (WEEE) contains metals of high commercial value and others that are supposed to be hazardous for the environment. Consequently, WEEE could be considered as a significant source for recovery of nonferrous metals. Among these wastes, computers appear to be distinctive, as far as further exploitation is concerned. The most ″useful″ parts of the computers are the printed circuit boards that contain many metals of interest. A study on microwave assisted electronic scrap (printed circuit boards of computer waste - PCBs) leaching was carried out with a microwave hydrothermal reactor. The leaching was conducted with thick slurries (50-100 g/L). The leaching media is a mixed solution of CuCl2 and NaCl. Preliminary electrolysis from leaching solution has investigated the feasibility of electrodeposition of copper. The results were discussed and compared with the conventional leaching method and demonstrated the potential for selective extraction of copper from PCBs.

Corrosion aspects of steel radioactive waste containers in cementitious materials

International Nuclear Information System (INIS)

Smart, Nick

2012-01-01

Nick Smart from Serco, UK, gave an overview of the effects of cementitious materials on the corrosion of steel during storage and disposal of various low- and intermediate-level radioactive wastes. Steel containers are often used as an overpack for the containment of radioactive wastes and are routinely stored in an open atmosphere. Since this is an aerobic and typically humid environment, the steel containers can start to corrode whilst in storage. Steel containers often come into contact with cementitious materials (e.g. grout encapsulants, backfill). An extensive account of different steel container designs and of steel corrosion mechanisms was provided. Steel corrosion rates under conditions buffered by cementitious materials have been evaluated experimentally. The main conclusion was that the cementitious environment generally facilitates the passivation of steel materials. Several general and localised corrosion mechanisms need to be considered when evaluating the performance of steel containers in cementitious environments, and environmental thresholds can be defined and used with this aim. In addition, the consequences of the generation of gaseous hydrogen by the corrosion of carbon steel under anoxic conditions must be taken into account. Discussion of the paper included: Is crevice corrosion really significant in cementitious systems? Crevice corrosion is unlikely in the cementitious backfill considered because it will tend to neutralise any acidic conditions in the crevice. What is the role of microbially-induced corrosion (MIC) in cementitious systems? Microbes are likely to be present in a disposal facility but their effect on corrosion is uncertain

Waste collection in developing countries – Tackling occupational safety and health hazards at their source

International Nuclear Information System (INIS)

Bleck, Daniela; Wettberg, Wieland

2012-01-01

Waste management procedures in developing countries are associated with occupational safety and health risks. Gastro-intestinal infections, respiratory and skin diseases as well as muscular-skeletal problems and cutting injuries are commonly found among waste workers around the globe. In order to find efficient, sustainable solutions to reduce occupational risks of waste workers, a methodological risk assessment has to be performed and counteractive measures have to be developed according to an internationally acknowledged hierarchy. From a case study in Addis Ababa, Ethiopia suggestions for the transferral of collected household waste into roadside containers are given. With construction of ramps to dump collected household waste straight into roadside containers and an adaptation of pushcarts and collection procedures, the risk is tackled at the source.

Effect of Recycled Waste Polymers, Natural Bitumen and HVS Cut on the Properties of Vacuum Bottom

Directory of Open Access Journals (Sweden)

Y. Rasoulzadeh

2013-01-01

Full Text Available The neat bitumen, an oil refining by-product, has its own inherent weakness under long-time loading at low and high temperatures. These performance limitations of neat bitumen have led researchers to modify its physical andmechanical properties. According to several studies, polymers can be used to modify the properties of bitumen. Due to much lower production costs and aiming to reduce environmental impacts, recycled waste polymers are preferred as compared with virgin polymers. In this study, the effect of recycled waste polymers including crumb rubber modifier (CRM, polyethylene and latex and non-polymeric materials such as natural bitumen (NB and heavy vacuum slops (HVS cut on physical and mechanical properties of vacuum bottom residue (VB of crude oil distillation was investigat-ed. Based on the results, recycled waste polyethylene and NB can improve the performance grade of VB at high temperatures and CRM, latex and HVS can improve the performance grade of VB at low temperatures. Thus, by designing various blends of these additives with VB, different modified bitumens can be directly obtained from VB without any need to air-blowing process.

DETERMINATION OF THE MINIMUM INTACT DIMENSIONS AVAILABLE IN PRACTICAL APPLICATIONS OF LASER CUTTING

Directory of Open Access Journals (Sweden)

Peter Gyorgy HORVATH

2016-06-01

Full Text Available The reuse of wastes is one of the main requirements of sustainable wood processing. Technologies available for waste management however are currently suited to the reuse of large quantities. This study investigates the utilisation of individual pieces of sawn wood and veneer wastes by laser cutting, with special emphasis on the search for the practical minimum intact dimension that can be produced by laser cutting

40 CFR 61.155 - Standard for operations that convert asbestos-containing waste material into nonasbestos...

Science.gov (United States)

2010-07-01

... to the information requirements of § 61.07(b)(3), a (i) Description of waste feed handling and...) Disposed of as asbestos-containing waste material according to § 61.150, or (ii) Recycled as waste feed... waste feed to the process. (2) Collect and analyze monthly composite samples (one 200-gram (7-ounce...

Comparison of Composting and Vermicomposting Processes in Refining Drill Cutting Mud from Ahvaz Oil Field in the Presence of Biosolids

Directory of Open Access Journals (Sweden)

afshin takdastan

2017-11-01

Full Text Available Cutting and drilling mud contains significant amounts of petroleum hydrocarbons that are detrimental to both the environment and public health. The objective of this study was to remove the hazardous components of drill cutting mud using the two biological processes of sewage sludge vermicomposting and biocomposting. In an experimental laboratory research, two pilot composting and vermicomposting processes, each over a period of two months with 2 repetitions, were conducted using the the same biological sludge mixed with drill cuttings contaminated with total petroleum hydrocarbon (TPH along with sawdust and yard waste. The GC-FID unit was used to determine the residual total petroleum hydrocarbon concentrations. Results showed that the vermicomposting pilot had a higher TPH removal efficiency than did the composting one so that TPH concentration in the mixed waste mass declined after 60 days from its original value of 42.004 g/kg to 11.316 g/kg. In other words, TPH removal in the pilots A (vermicomposting and B (biocomposting were 73/06% and 55/3%, respectively. Moreover, the TPH levels in the two composting and vermicomposting pilots on the 45th and 60th days showed significant differences (p < 0.05. The study showed that the vermicomposting process enjoys a higher capability than the composting one in removing TPH from oil-based drill cutting waste.

Explosive phenomena in heavily irradiated NaCl

NARCIS (Netherlands)

denHartog, HW; Vainshtein, DI; Matthews, GE; Williams, RT

1997-01-01

In heavily irradiated NaCl crystals explosive phenomena can be initiated during irradiation or afterwards when samples are heated to temperatures between 100 and 250 degrees C. During irradiation of NaCl Na and Cl-2 precipitates and void structures are produced along with the accumulation of stored

Container material and design considerations for storage of low-level radioactive waste

International Nuclear Information System (INIS)

Temus, C.J.

1987-01-01

With the threat of increased burial site restrictions and increased surcharges; the ease with which waste is sent to the burial site has been reduced. For many generators of waste the only alternative after maximizing volume reduction efforts is to store the waste. Even after working through the difficult decision of deciding what type of storage facility to have, the decision of what type of container to store the waste in has to still be made. This paper explores the many parameters that affect not only the material selection but also the design. The proper selection of materials affect the ability of the container to survive the storage period. The material selection also directly affects the design and utilization of the storage facility. The impacts to the facility include the functional aspects as well as its operational cost and liability as related to such things as fire insurance and active environmental control systems. The advantages and disadvantages of many of the common systems such as carbon steel, various coatings, polyethylene, stainless steel, composites and concrete will be discussed and evaluated. Recognizing that the waste is to be disposed of in the future differentiates it from waste that is shipped directly to the disposal site. The stored waste has to have the capability to be handled not only once like the disposal site waste but potentially several times before ultimate disposal. This handling may be by several different systems both at the storage facility and the burial site. Some of these systems due to ALARA considerations are usually remote requiring various interfaces, while not interfering with handling, transportation or disposal operations

Separation of uranium and common impurities from solid analytical waste containing plutonium

International Nuclear Information System (INIS)

Pathak, Nimai; Kumar, Mithlesh; Thulasidas, S.K.; Hon, N.S.; Kulkarni, M.J.; Mhatre, Amol; Natarajan, V.

2014-07-01

The report describes separation of uranium (U) and common impurities from solid analytical waste containing plutonium (Pu). This will be useful in recovery of Pu from nuclear waste. This is an important activity of any nuclear program in view of the strategic importance of Pu. In Radiochemistry Division, the trace metal analysis of Pu bearing fuel materials such as PuO 2 , (U,Pu)O 2 and (U,Pu)C are being carried out using the DC arc-Carrier Distillation technique. During these analyses, solid analytical waste containing Pu and 241 Am is generated. This comprises of left-over of samples and prepared charges. The main constituents of this waste are uranium oxide, plutonium oxide and silver chloride used as carrier. This report describes the entire work carried out to separate gram quantities of Pu from large amounts of U and mg quantities of 241 Am and the effect of leaching of the waste with nitric acid as a function of batch size. The effect of leaching the solid analytical waste of (U,Pu)O 2 and AgCl with concentrated nitric acid for different time intervals was also studied. Later keeping the time constant, the effect of nitric acid molarity on the leaching of U and Pu was investigated. Four different lots of the waste having different amounts were subjected to multiple leaching with 8 M nitric acid, each for 15 minutes duration. In all the experiments the amount of Uranium, Plutonium and other impurities leached were determined using ICP as an excitation source. The results are discussed in this report. (author)

Application of PINS and GNAT to the assay of 55-gal containers of radioactive waste

International Nuclear Information System (INIS)

Gehrke, R.J.; Aryaeinejad, R.; Watts, K.D.; Staples, D.R.; Akers, D.W.

1994-03-01

The Portable Isotropic Neutron Spectroscopy (PINS) and Gamma Neutron Assay Technique (GNAT) assay systems that were developed with funding from the office of Research and Development (NN20), were taken to the Stored Waste Examination Pilot Plant (SWEPP) facility at the Radioactive Waste Management Complex (RWMC) and applied to the assay of surrogate and Rocky Flats Plant waste contained in 55-gal drums. PINS, a portable prompt γ neutron activation analysis technique, was able to identify key elements in both the surrogate and real waste so that three-main waste categories: metal, combustible material, and cemented chlorinated sludge wastes could be identified. GNAT, a γ, neutron assay technique for the identification and quantification of fissioning isotopes, was able to identify 240 Pu in surrogate waste in which nine 1-g nuclear accident dosimeters were inserted. GNAT was also able to identify 24O Pu in real 55-gal waste drums containing 15- and 40-g of plutonium even in the presence of high activity concentrations of 241 Am

Mechanical and toxicological evaluation of concrete artifacts containing waste foundry sand.

Science.gov (United States)

Mastella, Miguel Angelo; Gislon, Edivelton Soratto; Pelisser, Fernando; Ricken, Cláudio; da Silva, Luciano; Angioletto, Elídio; Montedo, Oscar Rubem Klegues

2014-08-01

The creation of metal parts via casting uses molds that are generally made from sand and phenolic resin. The waste generated after the casting process is called waste foundry sand (WFS). Depending on the mold composition and the casting process, WFS can contain substances that prevent its direct emission to the environment. In Brazil, this waste is classified according to the Standard ABNT NBR 10004:2004 as a waste Class II (Non-Inert). The recycling of this waste is limited because its characteristics change significantly after use. Although the use (or reuse) of this byproduct in civil construction is a technically feasible alternative, its effects must be evaluated, especially from mechanical and environmental points of view. Thus, the objective of this study is to investigate the effect of the use of WFS in the manufacture of cement artifacts, such as masonry blocks for walls, structural masonry blocks, and paving blocks. Blocks containing different concentrations of WFS (up to 75% by weight) were produced and evaluated using compressive strength tests (35 MPa at 28 days) and toxicity tests on Daphnia magna, Allium cepa (onion root), and Eisenia foetida (earthworm). The results showed that there was not a considerable reduction in the compressive strength, with values of 35 ± 2 MPa at 28 days. The toxicity study with the material obtained from leaching did not significantly interfere with the development of D. magna and E. foetida, but the growth of the A. cepa species was reduced. The study showed that the use of this waste in the production of concrete blocks is feasible from both mechanical and environmental points of view. Copyright © 2014 Elsevier Ltd. All rights reserved.

Ocean disposal option for bulk wastes containing naturally occurring radionuclides: an assessment case history

International Nuclear Information System (INIS)

Stull, E.A.; Merry-Libby, P.

1985-01-01

There are 180,000 m 3 of slightly contaminated radioactive wastes (36 pCi/g radium-226) currently stored at the US Department of Energy's Niagara Falls Storage Site (NFSS), near Lewiston, New York. These wastes resulted from the cleanup of soils that were contaminated above the guidelines for unrestricted use of property. An alternative to long-term management of these wastes on land is dispersal in the ocean. A scenario for ocean disposal is presented for excavation, transport, and emplacement of these wastes in an ocean disposal site. The potential fate of the wastes and impacts on the ocean environment are analyzed, and uncertainties in the development of two worst-case scenarios for dispersion and pathway analyses are discussed. Based on analysis of a worst-case pathway back to man, the incremental dose from ingesting fish containing naturally occurring radionuclides from ocean disposal of the NFSS wastes is insignificant. Ocean disposal of this type of waste appears to be a technically promising alternative to the long-term maintenance costs and eventual loss of containment associated with management in a near-surface land burial facility

Waste management plan for the remedial investigation/feasibility study of Waste Area Grouping 5 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1992-12-01

This plan defines the criteria and methods to be used for managing waste generated during activities associated with Waste Area Grouping (WAG) 5 at Oak Ridge National Laboratory (ORNL). WAG 5 is located in Melton Valley, south of the main ORNL plant area. It contains 17 solid waste management units (SWMUs) to be evaluated during the remedial investigation. The SWMUs include three burial areas, two hydrofracture facilities, two settling ponds, eight tanks, and two low-level liquid waste leak sites. These locations are all considered to be within the WAG 5 area of contamination (AOC). The plan contains provisions for safely and effectively managing soils, rock cuttings, development and sampling water, decontamination fluids, and disposable personal protective equipment (PPE) consistent with the Environmental Protection Agency (EPA) guidance of May 1991 (EPA 1991). Consistent with EPA guidance, this plan is designed to protect the environment and the health and safety of workers and the public

Towards a safety case for the use of laser cutting in nuclear decommissioning

International Nuclear Information System (INIS)

Hilton, P.A.

2014-01-01

Some of the requirements in nuclear decommissioning include size reduction of contaminated containers, pipework and other structures manufactured from stainless and other steels. Size reduction is generally performed using mechanical saws or shears, with drawbacks of quick wear, significant applied force, difficult remote operation and addition to contaminated waste mass. The use of lasers for cutting within the context of nuclear decommissioning has been recently demonstrated by TWI and others. In this paper, aspects of drawing together a safety case for using laser beams for cutting in a nuclear decommissioning cell are discussed, via analysis of relevant purpose designed experimental data. Data presented includes assessment of the use of different focal length lenses and the power densities anticipated at distances of up to 3 m from the focal point, as well as beam effects on material behind the cutting zone. An assessment of anticipated material damage from stray beams or unintended exposure to laser light of surrounding items is also presented. Finally materials for effective screening against stray beams during the cutting process have been tested for effectiveness. (authors)

Corrosion of metal containers containing cemented radioactive wastes

International Nuclear Information System (INIS)

Duffo, G.S.; Farina, S.B.; Schulz, F.M.; Marotta, F

2010-01-01

Nuclear activities generate different kinds of radioactive wastes. In the case of Argentina, wastes classified as low and medium level are conditioned in metal drums for final disposal in a repository whose design is based on the use of multiple and independent barriers. Nuclear energy plants generate a large volume of mid-level radioactive wastes, consisting mainly of ion-exchange resins contaminated by fission products. Other contaminated products such as gloves, papers, clothing, rubber and plastic tubing, can be incinerated and the ashes from the combustion also constitute wastes that must be disposed of. These wastes (resins and ashes) must be immobilized in order to avoid the release of radionuclides into the environment. The wastes usually undergo a process of cementing to immobilize them. This work aims to systematically study the process of degradation by corrosion of the steel drums in contact with the cemented resins and with the ashes cemented with the addition of different types and concentrations of aggressive compounds (chloride and sulfate). The specimens are configured so that the parameters of interest for the steel in contact with the cemented materials can be measured. The variables of corrosion potential, electric resistivity of the matrix and polarization resistance (PR) were monitored and show that the presence of chloride increases the susceptibility to corrosion of the drum steel that is in contact with the cement resin matrix

Safety of systems for the retention of wastes containing radionuclides

International Nuclear Information System (INIS)

1980-11-01

Information and minimal requirements demanded by CNEN for the emission of the Approval Certificate of the Safety Analysis Report related to system for the retention of wastes containing radionuclide, are established, aiming to assure low radioactivity levels to the environment. (E.G.) [pt

Recovery of Proteins and Chromium Complexes from Chromium – Containing Leather Waste (CCLW

Directory of Open Access Journals (Sweden)

B. Gutti

2010-08-01

Full Text Available Chromium – Containing Leather Waste (CCLW constitutes an environmental pollution problem to leather industries disposing the waste by landfill. The waste mainly consists of collagen and chromium III complexes. This work is a design of reactors to recover gelatin, polypeptides and chromium from CCLW. The results of the experiment shows that 68% of protein, based on dry weight of leather scraps, could be recovered. Three reactors with a total volume of 18 m3 was designed to handle 10,431 kg of waste generated from the tanning industries.

Effect of applied voltage and initial concentration to desalting NaCl solution using electrodialysis

International Nuclear Information System (INIS)

Boubakri, Ali; Gzara, Lassaad; Dhahbi, Mahmoud; Bouguecha, Salah

2009-01-01

The desalination process of electrodialysis is one of membrane separation that competes with reverse osmosis for desalination of brackish water and seawater. In this work water desalination using a laboratory electrodialysis was performed and evaluated to desalting aqueous solutions containing 5000, 10000 and 20000 mg/L NaCl at different applied potential (10, 15 and 20 V) and at a constant flow rate of 3 L/min. Nine electrodialysis runs were performed. The results showed that the increasing of applied potential and decreasing of NaCl concentration have an important effect to enhance the electrodialysis performance. The efficiencies of each experiment were evaluated as function of specific power consumption with the electrical energy consumed in electrodialysis stack. It was obtained that the specific power consumption increased when the salt concentration and applied voltage increased. A laboratory electrodialysis stack containing fifteen cation exchange membranes and fifteen anion exchange membranes of 0,716 m 2 total effective area was used.

Characterization of Mechanical and Bactericidal Properties of Cement Mortars Containing Waste Glass Aggregate and Nanomaterials

Science.gov (United States)

Sikora, Pawel; Augustyniak, Adrian; Cendrowski, Krzysztof; Horszczaruk, Elzbieta; Rucinska, Teresa; Nawrotek, Pawel; Mijowska, Ewa

2016-01-01

The recycling of waste glass is a major problem for municipalities worldwide. The problem concerns especially colored waste glass which, due to its low recycling rate as result of high level of impurity, has mostly been dumped into landfills. In recent years, a new use was found for it: instead of creating waste, it can be recycled as an additive in building materials. The aim of the study was to evaluate the possibility of manufacturing sustainable and self-cleaning cement mortars with use of commercially available nanomaterials and brown soda-lime waste glass. Mechanical and bactericidal properties of cement mortars containing brown soda-lime waste glass and commercially available nanomaterials (amorphous nanosilica and cement containing nanocrystalline titanium dioxide) were analyzed in terms of waste glass content and the effectiveness of nanomaterials. Quartz sand is replaced with brown waste glass at ratios of 25%, 50%, 75% and 100% by weight. Study has shown that waste glass can act as a successful replacement for sand (up to 100%) to produce cement mortars while nanosilica is incorporated. Additionally, a positive effect of waste glass aggregate for bactericidal properties of cement mortars was observed. PMID:28773823

Characterization of Mechanical and Bactericidal Properties of Cement Mortars Containing Waste Glass Aggregate and Nanomaterials

Directory of Open Access Journals (Sweden)

Pawel Sikora

2016-08-01

Full Text Available The recycling of waste glass is a major problem for municipalities worldwide. The problem concerns especially colored waste glass which, due to its low recycling rate as result of high level of impurity, has mostly been dumped into landfills. In recent years, a new use was found for it: instead of creating waste, it can be recycled as an additive in building materials. The aim of the study was to evaluate the possibility of manufacturing sustainable and self-cleaning cement mortars with use of commercially available nanomaterials and brown soda-lime waste glass. Mechanical and bactericidal properties of cement mortars containing brown soda-lime waste glass and commercially available nanomaterials (amorphous nanosilica and cement containing nanocrystalline titanium dioxide were analyzed in terms of waste glass content and the effectiveness of nanomaterials. Quartz sand is replaced with brown waste glass at ratios of 25%, 50%, 75% and 100% by weight. Study has shown that waste glass can act as a successful replacement for sand (up to 100% to produce cement mortars while nanosilica is incorporated. Additionally, a positive effect of waste glass aggregate for bactericidal properties of cement mortars was observed.

Method of treating the waste liquid of a washing containing a radioactive substance

International Nuclear Information System (INIS)

Sawaguchi, Yusuke; Tsuyuki, Takashi; Kaneko, Masato; Sato, Yasuhiko; Yamaguchi, Takashi.

1975-01-01

Object: To separate waste liquid resulting from washing and which contains a radioactive substance and surface active agent into high purity water and a solid waste substance containing a small quantity of surface active agent. Structure: To waste liquid from a waste liquid tank is added a pH adjusting agent for adjusting the pH to 5.5, and the resultant liquid is sent to an agglomeration reaction tank, in which an inorganic agglomerating agent is added to the waste liquid to cause a major proportion of the radioactive substance and surface active agent to form flocks produced through agglomeration. Then, the waste liquid is sent from the agglomeration reaction tank to a froth separation tank, to which air is supplied through a perforated plate to cause frothing. The over-flowing liquid is de-frothed, and then the insoluble matter is separated as sludge, followed by hydroextraction and drying for solidification. The treated liquid extracted from a froth separation tank is sent to an agglomerating agent recovery tank for separation of the agglomeration agent, and then the residual surface active agent is removed by adsorption in an active carbon adsorption tower, followed by concentration by evaporation in an evaporating can. The concentrated liquid is extracted and then solidified with cement or asphalt. (Kamimura, M.)

Corrosion behaviour of groundnut shell ash and silicon carbide hybrid reinforced Al-Mg-Si alloy matrix composites in 3.5% NaCl and 0.3M H2SO4 solutions

Directory of Open Access Journals (Sweden)

Kenneth Kanayo ALANEME

2015-05-01

Full Text Available The corrosion behaviour of Al-Mg-Si alloy based composites reinforced with groundnut shell ash (GSA and silicon carbide (SiC was investigated. The aim is to assess the corrosion properties of Al-Mg-Si alloy based hybrid reinforced composites developed using different mix ratios of GSA (a cheaply processed agro waste derivative which served as partial replacement for SiC and SiC as reinforcing materials. GSA and SiC mixed in weight ratios 0:1, 1:3, 1:1, 3:1, and 1:0 were utilized to prepare 6 and 10 wt% of the reinforcing phase with Al‐Mg‐Si alloy as matrix using two‐step stir casting method. Mass loss and corrosion rate measurement was used to study the corrosion behaviour of the produced composites in 3.5% NaCl and 0.3M H2SO4 solutions. The results show that the Al-Mg-Si alloy based composites containing 6 and 10 wt% GSA and SiC in varied weight ratios were resistant to corrosion in 3.5% NaCl solution. The composites were however more susceptible to corrosion in 0.3M H2SO4 solution (in comparison with the 3.5% NaCl solution. It was noted that the Al-Mg-Si/6 wt% GSA-SiC hybrid composite grades containing GSA and SiC in weight ratio 1:3 and 3:1 respectively exhibited superior corrosion resistance in the 0.3M H2SO4 solution compared to other composites produced for this series. In the case of the Al-Mg-Si/10 wt% GSA-SiC hybrid composite grades, the corrosion resistance was relatively superior for the composites containing a greater weight ratio of GSA (75% and 100% in 0.3M H2SO4 solution.

Control of stress corrosion cracking in storage tanks containing radioactive waste

International Nuclear Information System (INIS)

Ondrejcin, R.S.; Rideout, S.P.; Donovan, J.A.

1978-01-01

Stress corrosion of carbon steel storage tanks containing alkaline nitrate radioactive waste, at the Savannah River Plant is controlled by specification of limits on waste composition and temperature. Cases of cracking have been observed in the primary steel shell of tanks designed and built before 1960 that were attributed to a combination of high residual stresses from fabrication welding and aggressiveness of fresh wastes from the reactor fuel reprocessing plants. The fresh wastes have the highest concentration of nitrate, which has been shown to be the cracking agent. Also as the waste solutions age and are reduced in volume by evaporation of water, nitrite and hydroxide ions become more concentrated and inhibit stress corrosion. Thus, by providing a heel of aged evaporated waste in tanks that receive fresh waste, concentrations of the inhibitor ions are maintained within specified ranges to protect against nitrate cracking. Tanks designed and built since 1960 have been made of steels with greater resistance to stress corrosion; these tanks have also been heat treated after fabrication to relieve residual stresses from construction operations. Temperature limits are also specified to protect against stress corrosion at elevated temperatures

Effect of halide salts on development of surface browning on fresh-cut 'Granny Smith' (Malus × domestica Borkh) apple slices during storage at low temperature.

Science.gov (United States)

Li, Yongxin; Wills, Ron B H; Golding, John B; Huque, Roksana

2015-03-30

The postharvest life of fresh-cut apple slices is limited by browning on cut surfaces. Dipping in halide salt solutions was examined for their inhibition of surface browning on 'Granny Smith' apple slices and the effects on biochemical factors associated with browning. Delay in browning by salts was greatest with chloride = phosphate > sulfate > nitrate with no difference between sodium, potassium and calcium ions. The effectiveness of sodium halides on browning was fluoride > chloride = bromide > iodide = control. Polyphenol oxidase (PPO) activity of tissue extracted from chloride- and fluoride-treated slices was not different to control but when added into the assay solution, NaF > NaCl both showed lower PPO activity at pH 3-5 compared to control buffer. The level of polyphenols in treated slices was NaF > NaCl > control. Addition of chlorogenic acid to slices enhanced browning but NaCl and NaF counteracted this effect. There was no effect of either halide salt on respiration, ethylene production, ion leakage, and antioxidant activity. Dipping apple slices in NaCl is a low cost treatment with few impediments to commercial use and could be a replacement for other anti-browning additives. The mode of action of NaCl and NaF is through decreasing PPO activity resulting in reduced oxidation of polyphenols. © 2014 Society of Chemical Industry.

New system for the container conditioning of liquid waste in the German future finale repository 'Schacht Konrad'

International Nuclear Information System (INIS)

Starke, H.

2012-01-01

The full text of publication follows. On-site the NPP Gundremmingen liquid radioactive waste from the NPP water treatment plant is stored in resin or concentrate collecting tanks. These liquid wastes are cemented in containers in order to temporarily store them in the Bavarian interim storage Mitterteich until they are transported into final repository in 'Schacht Konrad'. With this new system liquid radioactive waste is for the first time conditioned directly into containers destined for final repository in 'Schacht Konrad'. Thus, a very secure and sustainable procedure was developed which also provides high profitability. The conditioning plant for resins and concentrate extracts the liquid waste from the respective collecting tank and transports the waste to the separation tank. This separation tank is dimensioned to ensure complete filling of a Konrad container with only one batch. Within the tank there is the option to adjust the suspensions solids content by either extracting supernatant water or by adding de-ionised water. The specific activity is analysed and after the radiologic data and the solids content are available, the containers are cemented. The required amount of cement is based on the solids content and is automatically added. In the mixer, cement and primary waste suspension are mixed. This mixture is filled into the Konrad container via the allocator. The allocator is a funnel-shaped inlet equipped with a movable tube which makes sure the mixture is evenly spread and also ensures optimal filling of the Konrad container. While filling is ongoing, the container is covered by a lowerable splash guard to avoid contamination. The room situation in Gundremmingen and the specific activities of the primary waste suspension make it necessary to disperse the plant to several rooms. Main components such as separation tanks and pumps are installed in shielded rooms. All activities are conducted remotely controlled and are supervised from the central

Essays of leaching in cemented products containing simulated waste from evaporator concentrated of PWR reactor

International Nuclear Information System (INIS)

Haucz, Maria Judite A.; Calabria, Jaqueline A. Almeida; Tello, Cledola Cassia O.; Candido, Francisco Donizete; Seles, Sandro Rogerio Novaes

2011-01-01

This paper evaluated the results from leaching resistance essays of cemented products, prepared from three distinct formulations, containing simulated waste of concentrated from the PWR reactor evaporator. The leaching rate is a parameter of qualification of solidified products containing radioactive waste and is determined in accordance with regulation ISO 6961. This procedure evaluates the capacity of transfer organic and inorganic substances presents in the waste through dissolution in the extractor medium. For the case of radioactive waste it is reached the more retention of contaminants in the cemented product, i.e.the lesser value of lixiviation rate. Therefore, this work evaluated among the proposed formulation that one which attend the criterion established in the regulation CNEN-NN-6.09

Chemical alteration of calcium silicate hydrates in saline groundwater. Mechanism of sorption of Na on C-S-H and effect of NaCl on leaching of Ca from C-S-H

International Nuclear Information System (INIS)

Sugiyama, Daisuke; Fujita, Tomonari

2004-01-01

In the concept for TRU waste disposal in Japan, cement is a potential waste packaging and backfilling material and is expected to provide chemical containment. In the presence of some reactive ions in a saline groundwater, the chemical properties of cement materials should be affected. In this study, the mechanism of sorption of sodium (Na) on C-S-H and the effect of sodium chloride (NaCl) concentration on dissolution of Calcium Silicate Hydrate (C-S-H) are discussed by measuring the sorption isotherm of sodium onto C-S-H gel (Ca/Si = 0.65-1.2). Based on the experimental results, it is showed that sodium sorbs by substitution for Ca in C-S-H phases and leaching of Ca from C-S-H is enhanced in NaCl solution ( -1 mol dm -3 ). The results of sorption experiments are reasonably well modelled by the ion-exchange model assuming some calcium sites with different ion-exchange log K values. It is also suggested that the dissolution of C-S-H can be modelled reasonably well by considering the effect of ionic strength on activity coefficients of aqueous species for high Ca/Si ratio of C-S-H, and the effect of exchange of sodium with calcium of C-S-H on leaching of Ca becomes obvious for lower Ca/Si ratio of C-S-H. (author)

Fabrication and closure development of nuclear waste containers for storage at the Yucca Mountain, Nevada repository

International Nuclear Information System (INIS)

Russell, E.W.; Nelson, T.A.; Domian, H.A.; LaCount, D.F.; Robitz, E.S.; Stein, K.O.

1989-04-01

US Congress and the President have determined that the Yucca Mountain site in Nevada is to be characterized to determine its suitability for construction of the first US high-level nuclear waste repository. Work in connection with this site is carried out within the Yucca Mountain Project (YMP). Lawrence Livermore National Laboratory (LLNL) has the responsibility for designing, developing, and projecting the performance of the waste package for the permanent storage of high-level nuclear waste. Babcock ampersand Wilcox (B ampersand W) is involved with the YMP as a subcontractor to LLNL. B ampersand W's role is to recommend and demonstrate a method for fabricating the metallic waste container and a method for performing the final closure of the container after it has been filled with waste. Various fabrication and closure methods are under consideration for the production of containers. This paper presents progress to date in identifying and evaluating the candidate manufacturing processes. 2 refs., 1 fig., 7 tabs

Feasibility Study of Cryogenic Cutting Technology by Using a Computer Simulation and Manufacture of Main Components for Cryogenic Cutting System

International Nuclear Information System (INIS)

Kim, Sung Kyun; Lee, Dong Gyu; Lee, Kune Woo; Song, Oh Seop

2009-01-01

Cryogenic cutting technology is one of the most suitable technologies for dismantling nuclear facilities due to the fact that a secondary waste is not generated during the cutting process. In this paper, the feasibility of cryogenic cutting technology was investigated by using a computer simulation. In the computer simulation, a hybrid method combined with the SPH (smoothed particle hydrodynamics) method and the FE (finite element) method was used. And also, a penetration depth equation, for the design of the cryogenic cutting system, was used and the design variables and operation conditions to cut a 10 mm thickness for steel were determined. Finally, the main components of the cryogenic cutting system were manufactures on the basis of the obtained design variables and operation conditions.

Long time storage containers for spent fuels and vitrified wastes: synthesis of the studies

International Nuclear Information System (INIS)

Beziat, A.

2004-01-01

This report presents a synthesis of the studies relatives to the containers devoted to the long time spent fuels storage and vitrified wastes packages. These studies were realized in the framework of the axis 3 of the law of 1991 on the radioactive wastes management. The first part is devoted to the presentation of the studies. The container sizing studies which constitute the first containment barrier are then presented. The material choice and the closed system are also detailed. The studies were validate by the realization of containers models and an associated demonstration program is proposed. A synthesis of the technical and economical studies allowed to determine the components and operation costs. (A.L.B.)

A concept for a station for the encapsulation of vitrified highly radioactive waste into containers for final disposal

International Nuclear Information System (INIS)

Anon

1984-09-01

The report presents a concept and plans for a station for the encapsulation of vitrified highly radioactive waste into containers for final disposal. The process steps, the layout of the station, the main components of equipment and the sequence of operations under normal conditions are described. The station is designed for vitrified waste from reprocessing. The volume of the waste packages is 150 l, and each package contains the equivalent of 1.33 tonne HM of fuel. The radionuclide activity of the waste corresponds to spent fuel with a decay time of 40 years from discharge from the reactor. It is assumed that after transport under normal conditions the steel shell enclosing the waste is gastight and its surface is free of contamination. The containers for final disposal are made of cast steel and have the form of hollow cylinders with hemispherical ends; their overall length is 2 m and their overall diameter 0.94 m. The station is so designed that the whole procedure, from supply of the transport containers containing the waste to the delivery of the full final disposal containers, is carried out by remote control behind radiation screens in an area isolated from the environment. Containers that do not fulfill the quality control requirements can be improved or repaired in a special rework cell without interfering with the further normal operation of the plant. (author)

Characterizing the biotransformation of sulfur-containing wastes in simulated landfill reactors.

Science.gov (United States)

Sun, Wenjie; Sun, Mei; Barlaz, Morton A

2016-07-01

Landfills that accept municipal solid waste (MSW) in the U.S. may also accept a number of sulfur-containing wastes including residues from coal or MSW combustion, and construction and demolition (C&D) waste. Under anaerobic conditions that dominate landfills, microbially mediated processes can convert sulfate to hydrogen sulfide (H2S). The presence of H2S in landfill gas is problematic for several reasons including its low odor threshold, human toxicity, and corrosive nature. The objective of this study was to develop and demonstrate a laboratory-scale reactor method to measure the H2S production potential of a range of sulfur-containing wastes. The H2S production potential was measured in 8-L reactors that were filled with a mixture of the target waste, newsprint as a source of organic carbon required for microbial sulfate reduction, and leachate from decomposed residential MSW as an inoculum. Reactors were operated with and without N2 sparging through the reactors, which was designed to reduce H2S accumulation and toxicity. Both H2S and CH4 yields were consistently higher in reactors that were sparged with N2 although the magnitude of the effect varied. The laboratory-measured first order decay rate constants for H2S and CH4 production were used to estimate constants that were applicable in landfills. The estimated constants ranged from 0.11yr(-1) for C&D fines to 0.38yr(-1) for a mixed fly ash and bottom ash from MSW combustion. Copyright © 2016 Elsevier Ltd. All rights reserved.

Preliminary sensitivity analyses of corrosion models for BWIP [Basalt Waste Isolation Project] container materials

International Nuclear Information System (INIS)

Anantatmula, R.P.

1984-01-01

A preliminary sensitivity analysis was performed for the corrosion models developed for Basalt Waste Isolation Project container materials. The models describe corrosion behavior of the candidate container materials (low carbon steel and Fe9Cr1Mo), in various environments that are expected in the vicinity of the waste package, by separate equations. The present sensitivity analysis yields an uncertainty in total uniform corrosion on the basis of assumed uncertainties in the parameters comprising the corrosion equations. Based on the sample scenario and the preliminary corrosion models, the uncertainty in total uniform corrosion of low carbon steel and Fe9Cr1Mo for the 1000 yr containment period are 20% and 15%, respectively. For containment periods ≥ 1000 yr, the uncertainty in corrosion during the post-closure aqueous periods controls the uncertainty in total uniform corrosion for both low carbon steel and Fe9Cr1Mo. The key parameters controlling the corrosion behavior of candidate container materials are temperature, radiation, groundwater species, etc. Tests are planned in the Basalt Waste Isolation Project containment materials test program to determine in detail the sensitivity of corrosion to these parameters. We also plan to expand the sensitivity analysis to include sensitivity coefficients and other parameters in future studies. 6 refs., 3 figs., 9 tabs

Diamond wire cutting of heat exchangers

International Nuclear Information System (INIS)

Beckman, T.R.; Bjerler, J.

1991-01-01

With the change-out of equipment at nuclear power plants comes large quantities of low level contaminated metallic waste. Of particular concern are large heat exchangers, preheaters and steam generators. These bulky items consume huge volumes of burial space. The need for volume reduction and recycling of these metals has created new demands for 'how' to cut heat exchangers into useful sizes for decontamination, melting or compaction. This paper reviews the cutting solution provided by a diamond wire system, with particular regard for cutting of a Ringhals Preheater Bundle at Studsvik Nuclear in 1989. The background of diamond wire sawing is discussed and basic components of wire sawing are explained. Other examples of wire cutting decommissioned components are also given. (author)

NaCl stress-induced changes in the essential oil quality and abietane diterpene yield and composition in common sage

Directory of Open Access Journals (Sweden)

Taieb Tounekti

2015-09-01

Full Text Available Aim: The purpose of this study was to evaluate how increasing NaCl salinity in the medium can affects the essential oils (EOs composition and phenolic diterpene content and yield in leaves of Salvia officinalis L. The protective role of such compounds against NaCl stress was also argued with regard to some physiological characteristics of the plant (water and ionic relations as well as the leaf gas exchanges. Materials and Methods: Potted plants were exposed to increasing NaCl concentrations (0, 50, 75 and 100 mM for 4 weeks during July 2012. Replicates from each treatment were harvested after 0, 2, 3 and 4 weeks of adding salt to perform physiological measurements and biochemical analysis. Results: Sage EOs were rich in manool, viridiflorol, camphor, and borneol. Irrigation with a solution containing 100 mM NaCl for 4 weeks increased considerably 1.8-cineole, camphor and beta-thujone concentrations, whereas lower concentrations (50 and 75 mM had no effects. On the contrary, borneol and viridiflorol concentrations decreased significantly under the former treatment, while manool and total fatty acid concentrations were not affected. Leaf extracts contained also several diterpenes such as carnosic acid (CA, carnosol (CAR and 12- and #1054;-methoxy carnosic acid (MCA. The concentrations and total contents of CA and MCA increased after 3 weeks of irrigation with 75 or 100 mM NaCl. The 50 mM NaCl had no effect on these diterpenes. Our results suggest a protective role for CA against salinity stress. Conclusion: This study may provide ways to manipulate the concentration and yield of some phenolic diterpenes and EOs in sage. In fact soil salinity may favour a directional production of particular components of interest. [J Intercult Ethnopharmacol 2015; 4(3.000: 208-216

Nanoporous Glasses for Nuclear Waste Containment

Directory of Open Access Journals (Sweden)

Thierry Woignier

2016-01-01

Full Text Available Research is in progress to incorporate nuclear waste in new matrices with high structural stability, resistance to thermal shock, and high chemical durability. Interactions with water are important for materials used as a containment matrix for the radio nuclides. It is indispensable to improve their chemical durability to limit the possible release of radioactive chemical species, if the glass structure is attacked by corrosion. By associating high structural stability and high chemical durability, silica glass optimizes the properties of a suitable host matrix. According to an easy sintering stage, nanoporous glasses such as xerogels, aerogels, and composite gels are alternative ways to synthesize silica glass at relatively low temperatures (≈1,000–1,200°C. Nuclear wastes exist as aqueous salt solutions and we propose using the open pore structure of the nanoporous glass to enable migration of the solution throughout the solid volume. The loaded material is then sintered, thereby trapping the radioactive chemical species. The structure of the sintered materials (glass ceramics is that of nanocomposites: actinide phases (~100 nm embedded in a vitreous silica matrix. Our results showed a large improvement in the chemical durability of glass ceramic over conventional nuclear glass.

Electromagnetic mixed waste processing system for asbestos decontamination

Energy Technology Data Exchange (ETDEWEB)

Kasevich, R.S. [KAI Technologies, Inc., Portsmouth, NH (United States); Vaux, W.G. [Westinghouse Electric Corp., Pittsburgh, PA (United States); Nocito, T. [Ohio DSI Corp., New York (United States)

1995-10-01

DOE sites contain a broad spectrum of asbestos materials (cloth, pipe lagging, sprayed insulation and other substances) which are contaminated with a combination of hazardous and radioactive wastes due to its use during the development of the U.S. nuclear weapons complex. These wastes consist of cutting oils, lubricants, solvents, PCB`s, heavy metals and radioactive contaminants. The radioactive contaminants are the activation, decay and fission products of DOE operations. The asbestos must be converted by removing and separating the hazardous and radioactive materials to prevent the formation of mixed wastes and to allow for both sanitary disposal and effective decontamination. Currently, no technology exists that can meet these sanitary and other objectives.

Electromagnetic mixed waste processing system for asbestos decontamination

International Nuclear Information System (INIS)

Kasevich, R.S.; Vaux, W.G.; Nocito, T.

1995-01-01

DOE sites contain a broad spectrum of asbestos materials (cloth, pipe lagging, sprayed insulation and other substances) which are contaminated with a combination of hazardous and radioactive wastes due to its use during the development of the U.S. nuclear weapons complex. These wastes consist of cutting oils, lubricants, solvents, PCB's, heavy metals and radioactive contaminants. The radioactive contaminants are the activation, decay and fission products of DOE operations. The asbestos must be converted by removing and separating the hazardous and radioactive materials to prevent the formation of mixed wastes and to allow for both sanitary disposal and effective decontamination. Currently, no technology exists that can meet these sanitary and other objectives

Biochemical process of low level radioactive liquid simulation waste containing detergent

International Nuclear Information System (INIS)

Kundari, Noor Anis; Putra, Sugili; Mukaromah, Umi

2015-01-01

Research of biochemical process of low level radioactive liquid waste containing detergent has been done. Thse organic liquid wastes are generated in nuclear facilities such as from laundry. The wastes that are cotegorized as hazard and poison materials are also radioactive. It must be treated properly by detoxification of the hazard and decontamination of the radionuclides to ensure that the disposal of the waste meets the requirement of standard quality of water. This research was intended to determine decontamination factor and separation efficiensies, its kinetics law, and to produce a supernatant that ensured the environmental quality standard. The radioactive element in the waste was thorium with activity of 5.10 −5 Ci/m 3 . The radioactive liquid waste which were generated in simulation plant contains detergents that was further processed by aerobic biochemical process using SGB 103 bacteria in a batch reactor equipped with aerators. Two different concentration of samples were processed and analyzed for 212 hours and 183 hours respectively at a room temperature. The product of this process is a liquid phase called as supernatant and solid phase material called sludge. The chemical oxygen demand (COD), biological oxygen demand (BOD), suspended solid (SS), and its alpha activity were analyzed. The results show that the decontamination factor and the separation efficiency of the lower concentration samples are higher compared to the samples with high concentration. Regarding the decontamination factor, the result for 212 hours processing of waste with detergent concentration of 1.496 g/L was 3.496 times, whereas at the detergent concentration of 0.748 g/L was 15.305 times for 183 hours processing. In case of the separation efficiency, the results for both samples were 71.396% and 93.465% respectively. The Bacterial growth kinetics equation follow Monod’s model and the decreasing of COD and BOD were first order with the rate constant of 0.01 hour −1

Biochemical process of low level radioactive liquid simulation waste containing detergent

Energy Technology Data Exchange (ETDEWEB)

Kundari, Noor Anis, E-mail: nooranis@batan.go.id; Putra, Sugili; Mukaromah, Umi [Sekolah Tinggi Teknologi Nuklir – Badan Tenaga Nuklir Nasional Jl. Babarsari P.O. BOX 6101 YKBB Yogyakarta 55281 Telp : (0274) 48085, 489716, Fax : (0274) 489715 (Indonesia)

2015-12-29

Research of biochemical process of low level radioactive liquid waste containing detergent has been done. Thse organic liquid wastes are generated in nuclear facilities such as from laundry. The wastes that are cotegorized as hazard and poison materials are also radioactive. It must be treated properly by detoxification of the hazard and decontamination of the radionuclides to ensure that the disposal of the waste meets the requirement of standard quality of water. This research was intended to determine decontamination factor and separation efficiensies, its kinetics law, and to produce a supernatant that ensured the environmental quality standard. The radioactive element in the waste was thorium with activity of 5.10{sup −5} Ci/m{sup 3}. The radioactive liquid waste which were generated in simulation plant contains detergents that was further processed by aerobic biochemical process using SGB 103 bacteria in a batch reactor equipped with aerators. Two different concentration of samples were processed and analyzed for 212 hours and 183 hours respectively at a room temperature. The product of this process is a liquid phase called as supernatant and solid phase material called sludge. The chemical oxygen demand (COD), biological oxygen demand (BOD), suspended solid (SS), and its alpha activity were analyzed. The results show that the decontamination factor and the separation efficiency of the lower concentration samples are higher compared to the samples with high concentration. Regarding the decontamination factor, the result for 212 hours processing of waste with detergent concentration of 1.496 g/L was 3.496 times, whereas at the detergent concentration of 0.748 g/L was 15.305 times for 183 hours processing. In case of the separation efficiency, the results for both samples were 71.396% and 93.465% respectively. The Bacterial growth kinetics equation follow Monod’s model and the decreasing of COD and BOD were first order with the rate constant of 0

Biochemical process of low level radioactive liquid simulation waste containing detergent

Science.gov (United States)

Kundari, Noor Anis; Putra, Sugili; Mukaromah, Umi

2015-12-01

Research of biochemical process of low level radioactive liquid waste containing detergent has been done. Thse organic liquid wastes are generated in nuclear facilities such as from laundry. The wastes that are cotegorized as hazard and poison materials are also radioactive. It must be treated properly by detoxification of the hazard and decontamination of the radionuclides to ensure that the disposal of the waste meets the requirement of standard quality of water. This research was intended to determine decontamination factor and separation efficiensies, its kinetics law, and to produce a supernatant that ensured the environmental quality standard. The radioactive element in the waste was thorium with activity of 5.10-5 Ci/m3. The radioactive liquid waste which were generated in simulation plant contains detergents that was further processed by aerobic biochemical process using SGB 103 bacteria in a batch reactor equipped with aerators. Two different concentration of samples were processed and analyzed for 212 hours and 183 hours respectively at a room temperature. The product of this process is a liquid phase called as supernatant and solid phase material called sludge. The chemical oxygen demand (COD), biological oxygen demand (BOD), suspended solid (SS), and its alpha activity were analyzed. The results show that the decontamination factor and the separation efficiency of the lower concentration samples are higher compared to the samples with high concentration. Regarding the decontamination factor, the result for 212 hours processing of waste with detergent concentration of 1.496 g/L was 3.496 times, whereas at the detergent concentration of 0.748 g/L was 15.305 times for 183 hours processing. In case of the separation efficiency, the results for both samples were 71.396% and 93.465% respectively. The Bacterial growth kinetics equation follow Monod's model and the decreasing of COD and BOD were first order with the rate constant of 0.01 hour-1.

Limiting nutrient emission from a cut rose closed system by high-flux irrigation and low nutrient concentrations?

NARCIS (Netherlands)

Baas, R.; Berg, van der D.

2004-01-01

A two-year project was aimed at decreasing nutrient emission from closed nutrient systems by using high irrigation rates in order to allow lower EC levels in the presence of accumulated Na and Cl. Experimental variables were growing media, irrigation frequencies, EC and NaCl concentrations for cut

Method to prepare essentially organic waste liquids containing radioactive or toxic materials

International Nuclear Information System (INIS)

Baehr, W.; Drobnik, S.H.; Hild, W.; Kroebel, R.; Meyer, A.; Naumann, G.

1976-01-01

Waste solutions occuring in nuclear technology containing radioactive or toxic materials can be solidified by mixing with a polymerisable mixture with subsequent polymerization. An improvement of this method, especially for liquids in which the radioactive components are present as organic compounds is achieved by adding a mixture of at least one monomeric vinyl compound, at least one polyvinyl compound and appropriate catalysts and by polymerizing at temperatures between 15 and 150 0 C. Should the waste liquid contain mineral acid, this is first neutralized by the addition of CaO or MgO. In processing oils or soaps, the addition of swelling agent for polystyrol resins is advantageous. 16 examples illustrate the invention. (UWI) [de

Selection criteria for container materials at the proposed Yucca Mountain high level nuclear waste repository

International Nuclear Information System (INIS)

Halsey, W.G.

1989-11-01

A geological repository has been proposed for the permanent disposal of the nation's high level nuclear waste at Yucca Mountain in the Nevada desert. The containers for this waste must remain intact for the unprecedented service lifetime of 1000 years. A combination of engineering, regulatory, and licensing requirements complicate the container material selection. In parallel to gathering information regarding the Yucca Mountain service environment and material performance data, a set of selection criteria have been established which compare candidate materials to the performance requirements, and allow a quantitative comparison of candidates. These criteria assign relative weighting to varied topic areas such as mechanical properties, corrosion resistance, fabricability, and cost. Considering the long service life of the waste containers, it is not surprising that the corrosion behavior of the material is a dominant factor. 7 refs

Nonradioactive Air Emissions Notice of Construction (NOC) Application for the Central Waste Complex (CSC) for Storage of Vented Waste Containers

International Nuclear Information System (INIS)

KAMBERG, L.D.

2000-01-01

This Notice of Construction (NOC) application is submitted for the storage and management of waste containers at the Central Waste Complex (CWC) stationary source. The CWC stationary source consists of multiple sources of diffuse and fugitive emissions, as described herein. This NOC is submitted in accordance with the requirements of Washington Administrative Code (WAC) 173-400-110 (criteria pollutants) and 173-460-040 (toxic air pollutants), and pursuant to guidance provided by the Washington State Department of Ecology (Ecology). Transuranic (TRU) mixed waste containers at CWC are vented to preclude the build up of hydrogen produced as a result of radionuclide decay, not as safety pressure releases. The following activities are conducted within the CWC stationary source: Storage and inspection; Transfer and staging; Packaging; Treatment; and Sampling. This NOC application is intended to cover all existing storage structures within the current CWC treatment, storage, and/or disposal (TSD) boundary, as well as any storage structures, including waste storage pads and staging areas, that might be constructed in the future within the existing CWC boundary

Experiments on container materials for Swiss high-level waste disposal projects. Part IV

International Nuclear Information System (INIS)

Simpson, J.P.

1989-12-01

One concept for final disposal of high-level waste in switzerland consists of a repository at a depth of 1000 to 1500 m in the crystalline bedrock of Northern Switzerland. The waste will be placed in a container which will be required to function as a high integrity barrier for at least 100 years. This report is the fourth and last in the current series dealing with the evaluation of potential materials for such containers. Four materials were identified for further evaluation in the first of these reports: cast steel, nodular cast iron, copper and Ti-Code 12. This report deals with the problem of demonstrating that cast steel containers will not fail by stress corrosion cracking and with the problem of hydrogen produced by the reduction of water. The experimental results on pre-cracked specimens revealed no susceptibility of cast steel to stress corrosion cracking under model repository conditions. No crack growth was detected on compact DCB specimens exposed in aerobic and anaerobic groundwaters at 80 and 140 o C for 16-24 months. Cast steel remains a candidate material for high-level waste containers. As expected from thermodynamic considerations no hydrogen could be detected from copper immersed in model groundwaters at 50 o C. Hydrogen is evolved from corroding steel under anaerobic conditions. Hydrogen evolution due to corrosion of iron or steel in waste repositories has to be considered in any safety analysis; the amounts produced can be significant. Evidence todate suggests that both cast steel and copper are suitable container materials. Because the corrosion behaviour of both materials is sensitive to service conditions, in particular length of the aerobic phase, groundwater chemistry and temperature, further testing should be undertaken when a specific site has been identified. (author) 9 tabs., 11 figs., 25 refs

Treatment alternatives of liquid radioactive waste containing uranium in phosphoric acid

International Nuclear Information System (INIS)

Bustamante Escobedo, Mauricio

2003-01-01

The UGDR, receives annually 100 [l] of liquid radioactive waste containing, highly acid (pH=0) uranium in phosphoric acid from the Laboratory of Chemical Analysis. This waste must be chemically and radiologically decontaminated before it can be discharged in accordance with local environmental standards. Chemical precipitation and evaporation test were carried out to define the operating conditions for the radiological decontamination of this radioactive waste and to obtain a solid waste that can be conditioned in a cement matrix. The evaporation process generates excellent rates of volume reduction, over 80%, but generates a pulp that is hard handle when submitted to a drying process. Chemical precipitation generates good results for decontaminating these solutions and reducing volume (above 50%) to obtain a uranium free effluent. The treatment with calcium carbonate generated an effluent with a low concentration of polluting agents. A preliminary test was carried out condition these solids in a cement matrix, using ratios of 0.45 waste/cement and 2 of water/cement. The mix prepared with waste from the sodium hydroxide treatment had low mechanical resistance resulting from the saline incrustations. The waste from the calcium carbonate treatment was very porous due to the water evaporation from the highly exothermic reaction between the waste and the cement. The mix of the calcium carbonate generated waste and the cement matrix needs to be optimized, since it generates favorable conditions for adhering with the cement matrix (au)

Properties of slag concrete for low-level waste containment

International Nuclear Information System (INIS)

Langton, C.A.; Wong, P.B.

1991-01-01

Ground granulated blast furnace slag was incorporated in the concrete mix used for construction of low-level radioactive waste disposal vaults. The vaults were constructed as six 100 x 100 x 25 ft cells with each cell sharing internal walls with the two adjacent cells. The vaults were designed to contain a low-level radioactive wasteform called saltstone and to isolate the saltstone from the environment until the landfill is closed. Closure involves backfilling with native soil, installation of clay cap, and run-off control. The design criteria for the slag-substituted concrete included compressive strength, 4000 psi after 28 days; slump, 6 inch; permeability, less than 10 -7 cm/sec; and effective nitrate, chromium and technetium diffusivities of 10 -8 , 10 -12 and 10 -12 cm 2 /sec, respectively. The reducing capacity of the slag resulted in chemically reducing Cr +6 to Cr +3 and Tc +7 to Tc +4 and subsequent precipitation of the respective hydroxides in the alkaline pore solution. Consequently, the concrete vault enhances containment of otherwise mobile waste ions and contributes to the overall protection of the groundwater at the disposal site

Stabilization Using Phosphate Bonded Ceramics. Salt Containing Mixed Waste Treatment. Mixed Waste Focus Area. OST Reference No. 117

International Nuclear Information System (INIS)

1999-01-01

Throughout the Department of Energy (DOE) complex there are large inventories of homogeneous mixed waste solids, such as wastewater treatment residues, fly ashes, and sludges that contain relatively high concentrations (greater than 15% by weight) of salts. The inherent solubility of salts (e.g., nitrates, chlorides, and sulfates) makes traditional treatment of these waste streams difficult, expensive, and challenging. One alternative is low-temperature stabilization by chemically bonded phosphate ceramics (CBPCs). The process involves reacting magnesium oxide with monopotassium phosphate with the salt waste to produce a dense monolith. The ceramic makes a strong environmental barrier, and the metals are converted to insoluble, low-leaching phosphate salts. The process has been tested on a variety of surrogates and actual mixed waste streams, including soils, wastewater, flyashes, and crushed debris. It has also been demonstrated at scales ranging from 5 to 55 gallons. In some applications, the CBPC technology provides higher waste loadings and a more durable salt waste form than the baseline method of cementitious grouting. Waste form test specimens were subjected to a variety of performance tests. Results of waste form performance testing concluded that CBPC forms made with salt wastes meet or exceed both RCRA and recommended Nuclear Regulatory Commission (NRC) low-level waste (LLW) disposal criteria. Application of a polymer coating to the CBPC may decrease the leaching of salt anions, but continued waste form evaluations are needed to fully assess the deteriorating effects of this leaching, if any, over time.

Ceramic waste forms for fuel-containing masses at Chernobyl

International Nuclear Information System (INIS)

Oversby, V.M.

1994-05-01

The fuel materials originally in the core of the Chernobyl Unit 4 reactor are now present within the Ukrytie in three major forms: (1) very fine particles of fuel dispersed as dust (about 10 tonnes), (2) fragments of the destroyed core, and (3) lavas containing fuel, cladding, and other materials. All of these materials will need to be immobilized into waste forms suitable for final disposal. We propose a ceramic waste form system that could accommodate all three waste types with a single set of processing equipment. The waste form would include the mineral zirconolite for immobilization of actinide materials (including uranium), perovskite, nepheline, spinel, and other phases as dictated by the chemistry of the lava masses. Waste loadings as high as 50% U can be achieved if pyrochlore, a close relative of zirconolite, is used as the U host. The ceramic immobilization could be achieved with low additions of inert chemicals to minimize the final disposal volume while ensuring a durable product. The sequence of processing would be to collect and immobilize the fuel dust first. This material will require minimal preprocessing and will provide experience in the handling of the fuel materials. Core fragments would be processed next, using a cryogenic crushing stage to reduce the size prior to adding ceramic additives. The lavas would be processed last, which is compatible with the likely sequence of availability of materials and with the complexity of the operations. The lavas will require more adjustment of chemical additive composition than the other streams to ensure that the desired phases are produced in the waste form

Disposal of oil cuttings by downhole fracturing injections : slurry product specifications issues

International Nuclear Information System (INIS)

Radzuan Junin

1994-01-01

The technique of using on-site injection of oil contaminated drill cuttings is attracting considerable attention as a cost effective means of complying with environmental legislation concerning discharges of drilling wastes. The slurrification and injection of oil based cuttings into a casing annulus, a process developed in 1989 by a major oil and gas producer/ operator, has proven to be a significant step toward reduction of such environmental waste. This paper discusses the development of the cuttings reinjection, slurrification, slurry properties and benefits of quality slurry, and behaviour of solid laden slurries in a fracture in conjunction with down-hole disposal operations

Effect of NaCl induced floc disruption on biological disintegration of sludge for enhanced biogas production.

Science.gov (United States)

Kavitha, S; Kaliappan, S; Adish Kumar, S; Yeom, Ick Tae; Rajesh Banu, J

2015-09-01

In the present study, the influence of NaCl mediated bacterial disintegration of waste activated sludge (WAS) was evaluated in terms of disintegration and biodegradability of WAS. Floc disruption was efficient at 0.03 g/g SS of NaCl, promoting the shifts of extracellular proteins and carbohydrates from inner layers to extractable--soluble layers (90 mg/L), respectively. Outcomes of sludge disintegration reveal that the maximum solubilization achieved was found to be 23%, respectively. The model elucidating the parameter evaluation, explicates that floc disrupted--bacterially disintegrated sludge (S3) showed superior biodegradability of about 0.23 (gCOD/gCOD) than the bacterially disintegrated (S2) and control (S3) sludges of about 0.13 (gCOD/gCOD) and 0.05 (gCOD/gCOD), respectively. Cost evaluation of the present study affords net profits of approximately 2.5 USD and -21.5 USD in S3 and S2 sludge. Copyright © 2015 Elsevier Ltd. All rights reserved.

Survey of degradation modes of candidate materials for high-level radioactive-waste disposal containers

International Nuclear Information System (INIS)

Bullen, D.B.; Gdowski, G.E.

1988-08-01

Three copper-based alloys and three iron- to nickel-based austenitic alloys are being considered as possible materials for fabrication of high-level radioactive-waste disposal containers. The waste will include spent fuel assemblies from reactors as well as high-level waste in borosilicate glass and will be sent to the prospective site at Yucca Mountain, Nevada, for disposal. The copper-based alloy materials are CDA 102 (oxygen-free copper), CDA 613 (Cu-7Al), and CDA 715 (Cu-30Ni). The austenitic materials are Types 304L and 316L stainless steels and Alloy 825. The waste-package containers must maintain substantially complete containment for at least 300 yr and perhaps as long as 1000 yr, and they must be retrievable from the disposal site during the first 50 yr after emplacement. The containers will be exposed to high temperatures and high gamma radiation fields from the decay of high-level waste. This volume surveys the available data on the phase stability of both groups of candidate alloys. The austenitic alloys are reviewed in terms of the physical metallurgy of the iron-chromium-nickel system, martensite transformations, carbide formation, and intermetallic-phase precipitation. The copper-based alloys are reviewed in terms of their phase equilibria and the possibility of precipitation of the minor alloying constituents. For the austenitic materials, the ranking based on phase stability is: Alloy 825 (best), Type 316L stainless steel, and then Type 304L stainless steel (worst). For the copper-based materials, the ranking is: CDA 102 (oxygen-free copper) (best), and then both CDA 715 and CDA 613. 75 refs., 24 figs., 6 tabs

International feedback experience on the cutting of reactor internal components

International Nuclear Information System (INIS)

Boucau, J.

2014-01-01

Westinghouse capitalizes more than 30 years of experience in the cutting of internal components of reactor and their packaging in view of their storage. Westinghouse has developed and validated different methods for cutting: plasma torch cutting, high pressure abrasive water jet cutting, electric discharge cutting and mechanical cutting. A long feedback experience has enabled Westinghouse to list the pros and cons of each cutting technology. The plasma torch cutting is fast but rises dosimetry concerns linked to the control of the cuttings and the clarity of water. Abrasive water jet cutting requires the installation of costly safety devices and of an equipment for filtering water but this technology allows accurate cuttings in hard-to-reach zones. Mechanical cutting is the most favourable technology in terms of wastes generation and of the clarity of water but the cutting speed is low. (A.C.)

Recycling stabilised/solidified drill cuttings for forage production in acidic soils.

Science.gov (United States)

Kogbara, Reginald B; Dumkhana, Bernard B; Ayotamuno, Josiah M; Okparanma, Reuben N

2017-10-01

Stabilisation/solidification (S/S), which involves fixation and immobilisation of contaminants using cementitious materials, is one method of treating drill cuttings before final fate. This work considers reuse of stabilised/solidified drill cuttings for forage production in acidic soils. It sought to improve the sustainability of S/S technique through supplementation with the phytoremediation potential of plants, eliminate the need for landfill disposal and reduce soil acidity for better plant growth. Drill cuttings with an initial total petroleum hydrocarbon (TPH) concentration of 17,125 mg kg -1 and low concentrations of metals were treated with 5%, 10%, and 20% cement dosages. The treated drill cuttings were reused in granular form for growing a forage, elephant grass (Pennisetum purpureum), after mixing with uncontaminated soil. The grasses were also grown in uncontaminated soil. The phytoremediation and growth potential of the plants was assessed over a 12-week period. A mix ratio of one part drill cuttings to three parts uncontaminated soil was required for active plant growth. The phytoremediation ability of elephant grass (alongside abiotic losses) reduced the TPH level (up to 8795 mg kg -1 ) in the soil-treated-drill cuttings mixtures below regulatory (1000 mg kg -1 ) levels. There were also decreased concentrations of metals. The grass showed better heights and leaf lengths in soil containing drill cuttings treated with 5% cement dosage than in uncontaminated soil. The results suggest that recycling S/S treated drill cuttings for forage production may be a potential end use of the treated waste. Copyright © 2017 Elsevier Ltd. All rights reserved.

Properties of radioactive wastes and waste containers

International Nuclear Information System (INIS)

Morcos, N.; Dayal, R.

1982-01-01

This program is sponsored by the Nuclear Regulatory Commission to address basic concerns in assessing the performance of solidified radwaste. Experiments were initiated to address these concerns. In particular, leachability of solidified radwastes and the physical stability of the ensuing waste forms were evaluated. In addition, leaching experiments designed to address the effects of alternating wet/dry cycles and of varying the length of these cycles on the leach behavior of waste forms were initiated

Demonstration of close-coupled barriers for subsurface containment of buried waste. Conceptual test plan

Energy Technology Data Exchange (ETDEWEB)

Heiser, J. [Brookhaven National Laboratory, Upton, NY (United States); Dwyer, B. [Sandia National Laboratory, Albuquerque, NM (United States)

1995-07-01

Over the past five decades, the US Department of Energy (DOE) Complex sites have experienced numerous loss of confinement failures from underground storage tanks (USTs), piping systems, vaults, landfills, and other structures containing hazardous and mixed wastes. Consequently, efforts are being made to devise technologies that provide interim containment of waste sites while final remediation alternatives are developed. Barrier materials consisting of cement and polymer which will be emplaced beneath a 7500 liter tank. The stresses around the tank shall be evaluated during barrier construction.