WorldWideScience

Sample records for multicast routing protocols

  1. A SURVEY ON MULTICAST ROUTING PROTOCOLS FOR PERFORMANCE EVALUATION IN WIRELESS SENSOR NETWORK

    Directory of Open Access Journals (Sweden)

    A. Suruliandi

    2015-03-01

    Full Text Available Multicast is a process used to transfer same message to multiple receivers at the same time. This paper presents the simulation and analysis of the performance of six different multicast routing protocols for Wireless Sensor Network (WSN. They are On Demand Multicast Routing Protocol (ODMRP, Protocol for Unified Multicasting through Announcement (PUMA, Multicast Adhoc On demand Distance Vector Protocol (MAODV, Overlay Boruvka-based Adhoc Multicast Protocol (OBAMP, Application Layer Multicast Algorithm (ALMA and enhanced version of ALMA (ALMA-H for WSN. Among them, ODMRP, MAODV and PUMA are reactive protocols while OBAMP, ALMA and ALMA-H are proactive protocols. This paper compares the performance of these protocols with common parameters such as Throughput, Reliability, End-to-End delay and Packet Delivery Ratio (PDR with increasing the numbers of nodes and increasing the speed of the nodes. The main objective of this work is to select the efficient multicast routing protocol for WSN among six multicast routing protocol based on relative strength and weakness of each protocol. The summary of above six multicast routing protocols is presented with a table of different performance characteristics. Experimental result shows that ODMRP attains higher throughput, reliability and higher packet delivery ratio than other multicast routing protocol, while incurring far less end-to-end delay.

  2. A Multicast Protocol Utilizing On-demand Routing Strategy for MPRN

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    This paper proposes a multicast protocol utilizing ondemand routing strategy for mobile packet radio network. It does not maintain permanent route tables with full topological views. Instead, multicast senders apply on-demand procedures to dynamically discover routes and build forwarding group in this protocol. The data packets are propagated by each forwarding group member via scoped flooding, so the protocol can reduce network bandwidth overhead and avoid the propagation of potentially large routing updates throughout the network.

  3. Enhancing On-Demand Multicast Routing Protocols using Mobility Prediction in Mobile Ad-hoc Network

    Directory of Open Access Journals (Sweden)

    Nermin Makhlouf

    2014-08-01

    Full Text Available A Mobile Ad hoc Network (MANET is a self-organizing wireless communication network in which mobile devices are based on no infrastructure like base stations or access points. Minimal configuration and quick deployment make ad hoc networks suitable for emergency situations like disaster recovery or military conflict. Since node mobility may cause links to be broken frequently, a very important issue for routing in MANETs is how to set reliable paths which can last as long as possible. To solve this problem, non-random behaviors for the mobility patterns that mobile users exhibit are exploited. This paper introduces a scheme to improve On-Demand Multicast Routing Protocol (ODMRP performances by using mobility prediction. 

  4. WDM Network and Multicasting Protocol Strategies

    Directory of Open Access Journals (Sweden)

    Pinar Kirci

    2014-01-01

    Full Text Available Optical technology gains extensive attention and ever increasing improvement because of the huge amount of network traffic caused by the growing number of internet users and their rising demands. However, with wavelength division multiplexing (WDM, it is easier to take the advantage of optical networks and optical burst switching (OBS and to construct WDM networks with low delay rates and better data transparency these technologies are the best choices. Furthermore, multicasting in WDM is an urgent solution for bandwidth-intensive applications. In the paper, a new multicasting protocol with OBS is proposed. The protocol depends on a leaf initiated structure. The network is composed of source, ingress switches, intermediate switches, edge switches, and client nodes. The performance of the protocol is examined with Just Enough Time (JET and Just In Time (JIT reservation protocols. Also, the paper involves most of the recent advances about WDM multicasting in optical networks. WDM multicasting in optical networks is given as three common subtitles: Broadcast and-select networks, wavelength-routed networks, and OBS networks. Also, in the paper, multicast routing protocols are briefly summarized and optical burst switched WDM networks are investigated with the proposed multicast schemes.

  5. Secure Multicast Routing Algorithm for Wireless Mesh Networks

    Directory of Open Access Journals (Sweden)

    Rakesh Matam

    2016-01-01

    Full Text Available Multicast is an indispensable communication technique in wireless mesh network (WMN. Many applications in WMN including multicast TV, audio and video conferencing, and multiplayer social gaming use multicast transmission. On the other hand, security in multicast transmissions is crucial, without which the network services are significantly disrupted. Existing secure routing protocols that address different active attacks are still vulnerable due to subtle nature of flaws in protocol design. Moreover, existing secure routing protocols assume that adversarial nodes cannot share an out-of-band communication channel which rules out the possibility of wormhole attack. In this paper, we propose SEMRAW (SEcure Multicast Routing Algorithm for Wireless mesh network that is resistant against all known active threats including wormhole attack. SEMRAW employs digital signatures to prevent a malicious node from gaining illegitimate access to the message contents. Security of SEMRAW is evaluated using the simulation paradigm approach.

  6. A high performance totally ordered multicast protocol

    Science.gov (United States)

    Montgomery, Todd; Whetten, Brian; Kaplan, Simon

    1995-01-01

    This paper presents the Reliable Multicast Protocol (RMP). RMP provides a totally ordered, reliable, atomic multicast service on top of an unreliable multicast datagram service such as IP Multicasting. RMP is fully and symmetrically distributed so that no site bears un undue portion of the communication load. RMP provides a wide range of guarantees, from unreliable delivery to totally ordered delivery, to K-resilient, majority resilient, and totally resilient atomic delivery. These QoS guarantees are selectable on a per packet basis. RMP provides many communication options, including virtual synchrony, a publisher/subscriber model of message delivery, an implicit naming service, mutually exclusive handlers for messages, and mutually exclusive locks. It has commonly been held that a large performance penalty must be paid in order to implement total ordering -- RMP discounts this. On SparcStation 10's on a 1250 KB/sec Ethernet, RMP provides totally ordered packet delivery to one destination at 842 KB/sec throughput and with 3.1 ms packet latency. The performance stays roughly constant independent of the number of destinations. For two or more destinations on a LAN, RMP provides higher throughput than any protocol that does not use multicast or broadcast.

  7. QoS Supported IPTV Service Architecture over Hybrid-Tree-Based Explicit Routed Multicast Network

    Directory of Open Access Journals (Sweden)

    Chih-Chao Wen

    2012-01-01

    Full Text Available With the rapid advance in multimedia streaming and multicast transport technology, current IP multicast protocols, especially PIM-SM, become the major channel delivery mechanism for IPTV system over Internet. The goals for IPTV service are to provide two-way interactive services for viewers to select popular program channel with high quality for watching during fast channel surfing period. However, existing IP multicast protocol cannot meet above QoS requirements for IPTV applications between media server and subscribers. Therefore, we propose a cooperative scheme of hybrid-tree based on explicit routed multicast, called as HT-ERM to combine the advantages of shared tree and source tree for QoS-supported IPTV service. To increase network utilization, the constrained shortest path first (CSPF routing algorithm is designed for construction of hybrid tree to deliver the high-quality video stream over watching channel and standard quality over surfing channel. Furthermore, the Resource Reservation Protocol- Traffic Engineering (RSVP-TE is used as signaling mechanism to set up QoS path for multicast channel admission control. Our simulation results demonstrated that the proposed HT-ERM scheme outperforms other multicast QoS-based delivery scheme in terms of channel switching delay, resource utilization, and blocking ratio for IPTV service.

  8. Fault recovery in the reliable multicast protocol

    Science.gov (United States)

    Callahan, John R.; Montgomery, Todd L.; Whetten, Brian

    1995-01-01

    The Reliable Multicast Protocol (RMP) provides a unique, group-based model for distributed programs that need to handle reconfiguration events at the application layer. This model, called membership views, provides an abstraction in which events such as site failures, network partitions, and normal join-leave events are viewed as group reformations. RMP provides access to this model through an application programming interface (API) that notifies an application when a group is reformed as the result of a some event. RMP provides applications with reliable delivery of messages using an underlying IP Multicast (12, 5) media to other group members in a distributed environment even in the case of reformations. A distributed application can use various Quality of Service (QoS) levels provided by RMP to tolerate group reformations. This paper explores the implementation details of the mechanisms in RMP that provide distributed applications with membership view information and fault recovery capabilities.

  9. Pseudo-Cycle-Based Multicast Routing in Wormhole-Routed Networks

    Institute of Scientific and Technical Information of China (English)

    SONG JianPing (宋建平); HOU ZiFeng (侯紫峰); XU Ming (许铭)

    2003-01-01

    This paper addresses the problem of fault-tolerant multicast routing in wormholerouted multicomputers. A new pseudo-cycle-based routing method is presented for constructing deadlock-free multicast routing algorithms. With at most two virtual channels this technique can be applied to any connected networks with arbitrary topologies. Simulation results show that this technique results in negligible performance degradation even in the presence of a large number of faulty nodes.

  10. Dynamic multicast routing scheme in WDM optical network

    Science.gov (United States)

    Zhu, Yonghua; Dong, Zhiling; Yao, Hong; Yang, Jianyong; Liu, Yibin

    2007-11-01

    During the information era, the Internet and the service of World Wide Web develop rapidly. Therefore, the wider and wider bandwidth is required with the lower and lower cost. The demand of operation turns out to be diversified. Data, images, videos and other special transmission demands share the challenge and opportunity with the service providers. Simultaneously, the electrical equipment has approached their limit. So the optical communication based on the wavelength division multiplexing (WDM) and the optical cross-connects (OXCs) shows great potentials and brilliant future to build an optical network based on the unique technical advantage and multi-wavelength characteristic. In this paper, we propose a multi-layered graph model with inter-path between layers to solve the problem of multicast routing wavelength assignment (RWA) contemporarily by employing an efficient graph theoretic formulation. And at the same time, an efficient dynamic multicast algorithm named Distributed Message Copying Multicast (DMCM) mechanism is also proposed. The multicast tree with minimum hops can be constructed dynamically according to this proposed scheme.

  11. An Optical Multicast Routing with Minimal Network Coding Operations in WDM Networks

    Directory of Open Access Journals (Sweden)

    Huanlin Liu

    2014-01-01

    Full Text Available Network coding can improve the optical multicast routing performance in terms of network throughput, bandwidth utilization, and traffic load balance. But network coding needs high encoding operations costs in all-optical WDM networks due to shortage of optical RAM. In the paper, the network coding operation is defined to evaluate the number of network coding operation cost in the paper. An optical multicast routing algorithm based on minimal number of network coding operations is proposed to improve the multicast capacity. Two heuristic criteria are designed to establish the multicast routing with low network coding cost and high multicast capacity. One is to select one path from the former K shortest paths with the least probability of dropping the multicast maximal capacity. The other is to select the path with lowest potential coding operations with the highest link shared degree among the multiple wavelength disjoint paths cluster from source to each destination. Comparing with the other multicast routing based on network coding, simulation results show that the proposed multicast routing algorithm can effectively reduce the times of network coding operations, can improve the probability of reaching multicast maximal capacity, and can keep the less multicast routing link cost for optical WDM networks.

  12. Multicast routing for wavelength-routed WDM networks with dynamic membership

    Science.gov (United States)

    Huang, Nen-Fu; Liu, Te-Lung; Wang, Yao-Tzung; Li, Bo

    2000-09-01

    Future broadband networks must support integrated services and offer flexible bandwidth usage. In our previous work, we explore the optical link control layer on the top of optical layer that enables the possibility of bandwidth on-demand service directly over wavelength division multiplexed (WDM) networks. Today, more and more applications and services such as video-conferencing software and Virtual LAN service require multicast support over the underlying networks. Currently, it is difficult to provide wavelength multicast over the optical switches without optical/electronic conversions although the conversion takes extra cost. In this paper, based on the proposed wavelength router architecture (equipped with ATM switches to offer O/E and E/O conversions when necessary), a dynamic multicast routing algorithm is proposed to furnish multicast services over WDM networks. The goal is to joint a new group member into the multicast tree so that the cost, including the link cost and the optical/electronic conversion cost, is kept as less as possible. The effectiveness of the proposed wavelength router architecture as well as the dynamic multicast algorithm is evaluated by simulation.

  13. Multicasting in Wireless Communications (Ad-Hoc Networks): Comparison against a Tree-Based Approach

    Science.gov (United States)

    Rizos, G. E.; Vasiliadis, D. C.

    2007-12-01

    We examine on-demand multicasting in ad hoc networks. The Core Assisted Mesh Protocol (CAMP) is a well-known protocol for multicast routing in ad-hoc networks, generalizing the notion of core-based trees employed for internet multicasting into multicast meshes that have much richer connectivity than trees. On the other hand, wireless tree-based multicast routing protocols use much simpler structures for determining route paths, using only parent-child relationships. In this work, we compare the performance of the CAMP protocol against the performance of wireless tree-based multicast routing protocols, in terms of two important factors, namely packet delay and ratio of dropped packets.

  14. Design, Implementation, and Verification of the Reliable Multicast Protocol. Thesis

    Science.gov (United States)

    Montgomery, Todd L.

    1995-01-01

    This document describes the Reliable Multicast Protocol (RMP) design, first implementation, and formal verification. RMP provides a totally ordered, reliable, atomic multicast service on top of an unreliable multicast datagram service. RMP is fully and symmetrically distributed so that no site bears an undue portion of the communications load. RMP provides a wide range of guarantees, from unreliable delivery to totally ordered delivery, to K-resilient, majority resilient, and totally resilient atomic delivery. These guarantees are selectable on a per message basis. RMP provides many communication options, including virtual synchrony, a publisher/subscriber model of message delivery, a client/server model of delivery, mutually exclusive handlers for messages, and mutually exclusive locks. It has been commonly believed that total ordering of messages can only be achieved at great performance expense. RMP discounts this. The first implementation of RMP has been shown to provide high throughput performance on Local Area Networks (LAN). For two or more destinations a single LAN, RMP provides higher throughput than any other protocol that does not use multicast or broadcast technology. The design, implementation, and verification activities of RMP have occurred concurrently. This has allowed the verification to maintain a high fidelity between design model, implementation model, and the verification model. The restrictions of implementation have influenced the design earlier than in normal sequential approaches. The protocol as a whole has matured smoother by the inclusion of several different perspectives into the product development.

  15. Connectivity-Based Reliable Multicast MAC Protocol for IEEE 802.11 Wireless LANs

    Directory of Open Access Journals (Sweden)

    Woo-Yong Choi

    2009-01-01

    Full Text Available We propose the efficient reliable multicast MAC protocol based on the connectivity information among the recipients. Enhancing the BMMM (Batch Mode Multicast MAC protocol, the reliable multicast MAC protocol significantly reduces the RAK (Request for ACK frame transmissions in a reasonable computational time and enhances the MAC performance. By the analytical performance analysis, the throughputs of the BMMM protocol and our proposed MAC protocol are derived. Numerical examples show that our proposed MAC protocol increases the reliable multicast MAC performance for IEEE 802.11 wireless LANs.

  16. Implementing Resource-aware Multicast Forwarding in Software Defined Networks

    DEFF Research Database (Denmark)

    Poderys, Justas; Sunny, Anjusha; Soler, José

    2018-01-01

    Using multicast data transmissions, data can be eciently distributed to a high number of network users. However, in order to ef-ciently stream multimedia using multicast communication, multicast routing protocols must have knowledge of all network links and their available bandwidth. In Software...

  17. A Scalable and Fault-Tolerant Architecture for Internet Multicasting Using Meshes

    National Research Council Canada - National Science Library

    Garcia-Luna-Aceves, J. J; Balasubramaniyan, Saravanan; Balakrishnan, Ramesh

    2002-01-01

    ... communication within a group. A new protocol is presented for the creation and management of multicast meshes that substitute for the traditional multicast trees as the underlying routing structure for multipoint communication within groups...

  18. Reliable Multicast MAC Protocol for IEEE 802.11 Wireless LANs with Extended Service Range

    Science.gov (United States)

    Choi, Woo-Yong

    2011-11-01

    In this paper, we propose the efficient reliable multicast MAC protocol by which the AP (Access Point) can transmit reliably its multicast data frames to the recipients in the AP's one-hop or two-hop transmission range. The AP uses the STAs (Stations) that are directly associated with itself as the relays for the data delivery to the remote recipients that cannot be reached directly from itself. Based on the connectivity information among the recipients, the reliable multicast MAC protocol optimizes the number of the RAK (Request for ACK) frame transmissions in a reasonable computational time. Numerical examples show that our proposed MAC protocol significantly enhances the MAC performance compared with the BMMM (Batch Mode Multicast MAC) protocol that is extended to support the recipients that are in the AP's one-hop or two-hop transmission range in IEEE 802.11 wireless LANs.

  19. Corrections to "Connectivity-Based Reliable Multicast MAC Protocol for IEEE 802.11 Wireless LANs"

    Directory of Open Access Journals (Sweden)

    Choi Woo-Yong

    2010-01-01

    Full Text Available We have found the errors in the throughput formulae presented in our paper "Connectivity-based reliable multicast MAC protocol for IEEE 802.11 wireless LANs". We provide the corrected formulae and numerical results.

  20. A multicast tree aggregation algorithm in wavelength-routed WDM networks

    Science.gov (United States)

    Cheng, Hsu-Chen; Kuo, Chin-Chun; Lin, Frank Y.

    2005-02-01

    Wavelength division multiplexing (WDM) has been considered a promising transmission technology in optical communication networks. With the continuous advance in optical technology, WDM network will play an important role in wide area backbone networks. Optical wavelength switching, compared with optical packet switching, is a more mature and more cost-effective choice for optical switching technologies. Besides, the technology of time division multiplexing in optical communication networks has been working smoothly for a long time. In the proposed research, the problem of multicast groups aggregation and multicast routing and wavelength assignment in wavelength-routed WDM network is studied. The optical cross connect switches in the problem are assumed to have limited optical multicast/splitting and TDM functionalities. Given the physical network topology and capacity, the objective is to maximize the total revenue by means of utmost merging multicast groups into larger macro-groups. The groups in the same macro-group will share a multicast tree to conduct data transmission. The problem is formulated as an optimization problem, where the objective function is to maximize the total revenue subject to capacity constraints of components in the optical network, wavelength continuity constraints, and tree topology constraints. The decision variables in the formulations include the merging results between groups, multicast tree routing assignment and wavelength assignment. The basic approach to the algorithm development for this model is Lagrangean relaxation in conjunction with a number of optimization techniques. In computational experiments, the proposed algorithms are evaluated on different network topologies and perform efficiently and effectively according to the experiment results.

  1. Many-to-Many Multicast Routing Schemes under a Fixed Topology

    Directory of Open Access Journals (Sweden)

    Wei Ding

    2013-01-01

    Full Text Available Many-to-many multicast routing can be extensively applied in computer or communication networks supporting various continuous multimedia applications. The paper focuses on the case where all users share a common communication channel while each user is both a sender and a receiver of messages in multicasting as well as an end user. In this case, the multicast tree appears as a terminal Steiner tree (TeST. The problem of finding a TeST with a quality-of-service (QoS optimization is frequently NP-hard. However, we discover that it is a good idea to find a many-to-many multicast tree with QoS optimization under a fixed topology. In this paper, we are concerned with three kinds of QoS optimization objectives of multicast tree, that is, the minimum cost, minimum diameter, and maximum reliability. All of three optimization problems are distributed into two types, the centralized and decentralized version. This paper uses the dynamic programming method to devise an exact algorithm, respectively, for the centralized and decentralized versions of each optimization problem.

  2. Improvement In MAODV Protocol Using Location Based Routing Protocol

    Directory of Open Access Journals (Sweden)

    Kaur Sharnjeet

    2016-01-01

    Full Text Available Energy saving is difficult in wireless sensor network (WSN due to limited resources. Each node in WSN is constrained by their limited battery power for their energy. The energy is reduced as the time goes off due to the packet transmission and reception. Energy management techniques are necessary to minimize the total power consumption of all the nodes in the network in order to maximize its life span. Our proposed protocol Location based routing (LBR aimed to find a path which utilizes the minimum energy to transmit the packets between the source and the destination. The required energy for the transmission and reception of data is evaluated in MATLAB. LBR is implemented on Multicast Ad hoc On Demand Distance Vector Routing Protocol (MAODV to manage the energy consumption in the transmission and reception of data. Simulation results of LBR show the energy consumption has been reduced.

  3. An FEC Adaptive Multicast MAC Protocol for Providing Reliability in WLANs

    Science.gov (United States)

    Basalamah, Anas; Sato, Takuro

    For wireless multicast applications like multimedia conferencing, voice over IP and video/audio streaming, a reliable transmission of packets within short delivery delay is needed. Moreover, reliability is crucial to the performance of error intolerant applications like file transfer, distributed computing, chat and whiteboard sharing. Forward Error Correction (FEC) is frequently used in wireless multicast to enhance Packet Error Rate (PER) performance, but cannot assure full reliability unless coupled with Automatic Repeat Request forming what is knows as Hybrid-ARQ. While reliable FEC can be deployed at different levels of the protocol stack, it cannot be deployed on the MAC layer of the unreliable IEEE802.11 WLAN due to its inability to exchange ACKs with multiple recipients. In this paper, we propose a Multicast MAC protocol that enhances WLAN reliability by using Adaptive FEC and study it's performance through mathematical analysis and simulation. Our results show that our protocol can deliver high reliability and throughput performance.

  4. The specification-based validation of reliable multicast protocol: Problem Report. M.S. Thesis

    Science.gov (United States)

    Wu, Yunqing

    1995-01-01

    Reliable Multicast Protocol (RMP) is a communication protocol that provides an atomic, totally ordered, reliable multicast service on top of unreliable IP multicasting. In this report, we develop formal models for RMP using existing automated verification systems, and perform validation on the formal RMP specifications. The validation analysis help identifies some minor specification and design problems. We also use the formal models of RMP to generate a test suite for conformance testing of the implementation. Throughout the process of RMP development, we follow an iterative, interactive approach that emphasizes concurrent and parallel progress of implementation and verification processes. Through this approach, we incorporate formal techniques into our development process, promote a common understanding for the protocol, increase the reliability of our software, and maintain high fidelity between the specifications of RMP and its implementation.

  5. Optimización multiobjetivo para enrutamiento multicast en overlay networks utilizando algoritmos evolutivos Multiobjective Optimization for Multicast Routing in Overlay Networks using Evolutionary Algorithms

    Directory of Open Access Journals (Sweden)

    Juan Carlos Montoya M.

    2008-06-01

    Full Text Available Multicast juega un papel muy importante para soportar una nueva generación de aplicaciones. En la actualidad y por diferentes razones, técnicas y no técnicas, multicast IP no ha sido totalmente adoptado en Internet. Durante los últimos a˜nos, un área de investigación activa es la de implementar este tipo de tráfico desde la perspectiva del nivel de aplicación, donde la funcionalidad de multicast no es responsabilidad de los enrutadores sino de los hosts, a lo que se le conoce como Multicast Overlay Network (MON. En este artículo se plantea el enrutamiento en MON como un problema de Optimización Multiobjetivo (MOP donde se optimizan dos funciones: 1 el retardo total extremo a extremo del árbol multicast, y 2 la máxima utilización de los enlaces. La optimización simultánea de estas dos funciones es un problema NP completo y para resolverlo se propone utilizar Algoritmos Evolutivos Multiobjetivos (MOEA, específicamente NSGAIMulticast plays an important role in supporting a new generation of applications. At present and for different reasons, technical and non–technical, multicast IP hasn’t yet been totally adopted for Internet. During recent years, an active area of research is that of implementing this kind of traffic in the application layer where the multicast functionality isn´t a responsibility of the routers but that of the hosts, which we know as Multicast Overlay Networks (MON. In this article, routing in an MON is put forward as a multiobjective optimization problem (MOP where two functions are optimized: 1 the total end to end delay of the multicast tree and 2 the maximum link utilization. The simultaneous optimization of these two functions is an NP–Complete problem and to solve this we suggest using Multiobjective Evolutionary Algorithms (MOEA, specifically NSGA–II.

  6. Implementing Resource-aware Multicast Forwarding in Software Defined Networks

    DEFF Research Database (Denmark)

    Poderys, Justas; Sunny, Anjusha; Soler, José

    2018-01-01

    Using multicast data transmissions, data can be eciently distributed to a high number of network users. However, in order to ef-ciently stream multimedia using multicast communication, multicast routing protocols must have knowledge of all network links and their available bandwidth. In Software......-Karp algorithm, by taking into account network topology and links load information. This paper presents the algorithm, implementation details, and an analysis of the testing results....

  7. Optical multicast system for data center networks.

    Science.gov (United States)

    Samadi, Payman; Gupta, Varun; Xu, Junjie; Wang, Howard; Zussman, Gil; Bergman, Keren

    2015-08-24

    We present the design and experimental evaluation of an Optical Multicast System for Data Center Networks, a hardware-software system architecture that uniquely integrates passive optical splitters in a hybrid network architecture for faster and simpler delivery of multicast traffic flows. An application-driven control plane manages the integrated optical and electronic switched traffic routing in the data plane layer. The control plane includes a resource allocation algorithm to optimally assign optical splitters to the flows. The hardware architecture is built on a hybrid network with both Electronic Packet Switching (EPS) and Optical Circuit Switching (OCS) networks to aggregate Top-of-Rack switches. The OCS is also the connectivity substrate of splitters to the optical network. The optical multicast system implementation requires only commodity optical components. We built a prototype and developed a simulation environment to evaluate the performance of the system for bulk multicasting. Experimental and numerical results show simultaneous delivery of multicast flows to all receivers with steady throughput. Compared to IP multicast that is the electronic counterpart, optical multicast performs with less protocol complexity and reduced energy consumption. Compared to peer-to-peer multicast methods, it achieves at minimum an order of magnitude higher throughput for flows under 250 MB with significantly less connection overheads. Furthermore, for delivering 20 TB of data containing only 15% multicast flows, it reduces the total delivery energy consumption by 50% and improves latency by 55% compared to a data center with a sole non-blocking EPS network.

  8. Energy Reduction Multipath Routing Protocol for MANET Using Recoil Technique

    Directory of Open Access Journals (Sweden)

    Rakesh Kumar Sahu

    2018-04-01

    maximization (AOMR-LM and Source routing-based multicast protocol (SRMP algorithms. Hence, the AOMDV-ER algorithm performs better than these recently developed algorithms.

  9. Specification and Design of a Fault Recovery Model for the Reliable Multicast Protocol

    Science.gov (United States)

    Montgomery, Todd; Callahan, John R.; Whetten, Brian

    1996-01-01

    The Reliable Multicast Protocol (RMP) provides a unique, group-based model for distributed programs that need to handle reconfiguration events at the application layer. This model, called membership views, provides an abstraction in which events such as site failures, network partitions, and normal join-leave events are viewed as group reformations. RMP provides access to this model through an application programming interface (API) that notifies an application when a group is reformed as the result of a some event. RMP provides applications with reliable delivery of messages using an underlying IP Multicast media to other group members in a distributed environment even in the case of reformations. A distributed application can use various Quality of Service (QoS) levels provided by RMP to tolerate group reformations. This paper explores the implementation details of the mechanisms in RMP that provide distributed applications with membership view information and fault recovery capabilities.

  10. Alcatel-Lucent Service Routing Architect (SRA) self-study guide preparing for the BGP, VPRN and Multicast exams

    CERN Document Server

    Warnock, Glenn; Shaheen, Ghassan

    2015-01-01

    A comprehensive resource for professionals preparing for Alcatel-Lucent Service Routing Architect (SRA) certification Networking professionals are taking note of Alcatel-Lucent and its quick ascent in the networking and telecom industries. IP networking professionals looking for a comprehensive guide to obtaining the Alcatel-Lucent Service Routing Architect (SRA) certification will be pleased to learn of this new publication, Alcatel-Lucent Service Routing Architect (SRA) Self-Study Guide: Preparing for the BGP, VPRN and Multicast Exams. The book comprises approximately 2,600 pages of print a

  11. MeshTree: A Delay optimised Overlay Multicast Tree Building Protocol

    OpenAIRE

    Tan, Su-Wei; Waters, A. Gill; Crawford, John

    2005-01-01

    We study decentralised low delay degree-constrained overlay multicast tree construction for single source real-time applications. This optimisation problem is NP-hard even if computed centrally. We identify two problems in traditional distributed solutions, namely the greedy problem and delay-cost trade-off. By offering solutions to these problems, we propose a new self-organising distributed tree building protocol called MeshTree. The main idea is to embed the delivery tree in a degree-bound...

  12. High Performance Computing Multicast

    Science.gov (United States)

    2012-02-01

    A History of the Virtual Synchrony Replication Model,” in Replication: Theory and Practice, Charron-Bost, B., Pedone, F., and Schiper, A. (Eds...Performance Computing IP / IPv4 Internet Protocol (version 4.0) IPMC Internet Protocol MultiCast LAN Local Area Network MCMD Dr. Multicast MPI

  13. Multi-area layered multicast scheme for MPLS networks

    Science.gov (United States)

    Ma, Yajie; Yang, Zongkai; Wang, Yuming; Chen, Jingwen

    2005-02-01

    Multi-protocol label switching (MPLS) is multiprotocols both at layer 2 and layer 3. It is suggested to overcome the shortcomings of performing complex longest prefix matching in layer 3 routing by using short, fixed length labels. The MPLS community has put more effort into the label switching of unicast IP traffic, but less in the MPLS multicast mechanism. The reasons are the higher label consumption, the dynamical mapping of L3 multicast tree to L2 LSPs and the 20-bit shim header which is much fewer than the IPv4 IP header. On the other hand, heterogeneity of node capability degrades total performance of a multicast group. In order to achieve the scalability as well as the heterogeneity in MPLS networks, a novel scheme of MPLS-based Multi-area Layered Multicast Scheme (MALM) is proposed. Unlike the existing schemes which focus on aggregating the multicast stream, we construct the multicast tree based on the virtual topology aggregation. The MPLS area is divided into different sub-areas to form the hierarchical virtual topology and the multicast group is reconstructed into multiple layers according to the node capability. At the same time, the label stack is used to save the label space. For stability of the MALM protocol, a multi-layer protection scheme is also discussed. The experiment results show that the proposed scheme saves label space and decrease the Multicast Forwarding Table in much degree.

  14. VANET Routing Protocols: Pros and Cons

    OpenAIRE

    Paul, Bijan; Ibrahim, Md.; Bikas, Md. Abu Naser

    2012-01-01

    VANET (Vehicular Ad-hoc Network) is a new technology which has taken enormous attention in the recent years. Due to rapid topology changing and frequent disconnection makes it difficult to design an efficient routing protocol for routing data among vehicles, called V2V or vehicle to vehicle communication and vehicle to road side infrastructure, called V2I. The existing routing protocols for VANET are not efficient to meet every traffic scenarios. Thus design of an efficient routing protocol h...

  15. Simulation-Based Performance Evaluation of Predictive-Hashing Based Multicast Authentication Protocol

    Directory of Open Access Journals (Sweden)

    Seonho Choi

    2012-12-01

    Full Text Available A predictive-hashing based Denial-of-Service (DoS resistant multicast authentication protocol was proposed based upon predictive-hashing, one-way key chain, erasure codes, and distillation codes techniques [4, 5]. It was claimed that this new scheme should be more resistant to various types of DoS attacks, and its worst-case resource requirements were derived in terms of coarse-level system parameters including CPU times for signature verification and erasure/distillation decoding operations, attack levels, etc. To show the effectiveness of our approach and to analyze exact resource requirements in various attack scenarios with different parameter settings, we designed and implemented an attack simulator which is platformindependent. Various attack scenarios may be created with different attack types and parameters against a receiver equipped with the predictive-hashing based protocol. The design of the simulator is explained, and the simulation results are presented with detailed resource usage statistics. In addition, resistance level to various types of DoS attacks is formulated with a newly defined resistance metric. By comparing these results to those from another approach, PRABS [8], we show that the resistance level of our protocol is greatly enhanced even in the presence of many attack streams.

  16. Design, Implementation, and Performance Evaluation of Efficient PMIPv6 Based Mobile Multicast Sender Support Schemes

    Directory of Open Access Journals (Sweden)

    Lili Wang

    2015-01-01

    Full Text Available Proxy Mobile IPv6 (PMIPv6 is proposed as a promising network-based mobility management protocol, which does not need any participation of mobile nodes. PMIPv6 does not support the multicast well and most of the current research concentrates on the mobile multicast receiver. However, the mobile multicast sender is also very important and challenging, which has not been addressed well. Therefore, in this paper we propose two efficient PMIPv6 based mobile multicast sender support schemes which are PMIP bidirectional tunneling (PMIP-BT and PMIP direct routing (PMIP-DR. In the PMIP-BT, the multicast traffic can be delivered through the PMIPv6 bidirectional tunnel, while, in the PMIP-DR, the multicast data can be transmitted via an optimized direct multicast routing. Both of them can support the multicast sender mobility transparently enabled in the PMIPv6 networks. We evaluate the performance of the proposed schemes by theoretical analysis, and the numerical results show that the proposed schemes have a better performance in terms of the signaling cost than the current schemes. Meanwhile, the proposed schemes are also implemented on the test bed, and the experimental results not only verify the validity and feasibility of our proposed schemes, but also conclude the different scenarios to which they are applicable.

  17. Generalized routing protocols for multihop relay networks

    KAUST Repository

    Khan, Fahd Ahmed

    2011-07-01

    Performance of multihop cooperative networks depends on the routing protocols employed. In this paper we propose the last-n-hop selection protocol, the dual path protocol, the forward-backward last-n-hop selection protocol and the forward-backward dual path protocol for the routing of data through multihop relay networks. The average symbol error probability performance of the schemes is analysed by simulations. It is shown that close to optimal performance can be achieved by using the last-n-hop selection protocol and its forward-backward variant. Furthermore we also compute the complexity of the protocols in terms of number of channel state information required and the number of comparisons required for routing the signal through the network. © 2011 IEEE.

  18. A Geographical Heuristic Routing Protocol for VANETs

    Science.gov (United States)

    Urquiza-Aguiar, Luis; Tripp-Barba, Carolina; Aguilar Igartua, Mónica

    2016-01-01

    Vehicular ad hoc networks (VANETs) leverage the communication system of Intelligent Transportation Systems (ITS). Recently, Delay-Tolerant Network (DTN) routing protocols have increased their popularity among the research community for being used in non-safety VANET applications and services like traffic reporting. Vehicular DTN protocols use geographical and local information to make forwarding decisions. However, current proposals only consider the selection of the best candidate based on a local-search. In this paper, we propose a generic Geographical Heuristic Routing (GHR) protocol that can be applied to any DTN geographical routing protocol that makes forwarding decisions hop by hop. GHR includes in its operation adaptations simulated annealing and Tabu-search meta-heuristics, which have largely been used to improve local-search results in discrete optimization. We include a complete performance evaluation of GHR in a multi-hop VANET simulation scenario for a reporting service. Our study analyzes all of the meaningful configurations of GHR and offers a statistical analysis of our findings by means of MANOVA tests. Our results indicate that the use of a Tabu list contributes to improving the packet delivery ratio by around 5% to 10%. Moreover, if Tabu is used, then the simulated annealing routing strategy gets a better performance than the selection of the best node used with carry and forwarding (default operation). PMID:27669254

  19. Incentive Compatible and Globally Efficient Position Based Routing for Selfish Reverse Multicast in Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Sarvesh Varatharajan

    2009-10-01

    Full Text Available We consider the problem of all-to-one selfish routing in the absence of a payment scheme in wireless sensor networks, where a natural model for cost is the power required to forward, referring to the resulting game as a Locally Minimum Cost Forwarding (LMCF. Our objective is to characterize equilibria and their global costs in terms of stretch and diameter, in particular finding incentive compatible algorithms that are also close to globally optimal. We find that although social costs for equilibria of LMCF exhibit arbitrarily bad worst-case bounds and computational infeasibility of reaching optimal equilibria, there exist greedy and local incentive compatible heuristics achieving near-optimal global costs.

  20. A Clustering Routing Protocol for Mobile Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    Jinke Huang

    2016-01-01

    Full Text Available The dynamic topology of a mobile ad hoc network poses a real challenge in the design of hierarchical routing protocol, which combines proactive with reactive routing protocols and takes advantages of both. And as an essential technique of hierarchical routing protocol, clustering of nodes provides an efficient method of establishing a hierarchical structure in mobile ad hoc networks. In this paper, we designed a novel clustering algorithm and a corresponding hierarchical routing protocol for large-scale mobile ad hoc networks. Each cluster is composed of a cluster head, several cluster gateway nodes, several cluster guest nodes, and other cluster members. The proposed routing protocol uses proactive protocol between nodes within individual clusters and reactive protocol between clusters. Simulation results show that the proposed clustering algorithm and hierarchical routing protocol provide superior performance with several advantages over existing clustering algorithm and routing protocol, respectively.

  1. Advanced routing protocols for wireless networks

    CERN Document Server

    Campista , Miguel Elias Mitre

    2014-01-01

    This text introduces the principles of routing protocols and metrics as they affect wireless networking environments, specifically in urban areas. Timely because of the recent rise in small city life, this topic includes the consideration of ad hoc, mesh, vehicular, sensor, and delay tolerant networks. These approaches are each unique, and author Miguel Mitre Campista provides a thorough, but accessible, explanation of their individual characteristics for engineers, computer scientists, IT professionals, and curious Internet users.

  2. CBHRP: A Cluster Based Routing Protocol for Wireless Sensor Network

    OpenAIRE

    Rashed, M. G.; Kabir, M. Hasnat; Rahim, M. Sajjadur; Ullah, Sk. Enayet

    2012-01-01

    A new two layer hierarchical routing protocol called Cluster Based Hierarchical Routing Protocol (CBHRP) is proposed in this paper. It is an extension of LEACH routing protocol. We introduce cluster head-set idea for cluster-based routing where several clusters are formed with the deployed sensors to collect information from target field. On rotation basis, a head-set member receives data from the neighbor nodes and transmits the aggregated results to the distance base station. This protocol ...

  3. An improved AODV routing protocol based on tower structure

    Directory of Open Access Journals (Sweden)

    Li Yong Qiang

    2016-01-01

    Full Text Available The paper proposed a new routing protocol(IAODV based on tower structure in the Ad Hoc network for the problem which Location Routing Protocol need hardware and Complex algorithm. By the simulation, The complexity of the new routing protocol is reduced without reducing the performance of the network.

  4. Sigma Routing Metric for RPL Protocol

    Directory of Open Access Journals (Sweden)

    Paul Sanmartin

    2018-04-01

    Full Text Available This paper presents the adaptation of a specific metric for the RPL protocol in the objective function MRHOF. Among the functions standardized by IETF, we find OF0, which is based on the minimum hop count, as well as MRHOF, which is based on the Expected Transmission Count (ETX. However, when the network becomes denser or the number of nodes increases, both OF0 and MRHOF introduce long hops, which can generate a bottleneck that restricts the network. The adaptation is proposed to optimize both OFs through a new routing metric. To solve the above problem, the metrics of the minimum number of hops and the ETX are combined by designing a new routing metric called SIGMA-ETX, in which the best route is calculated using the standard deviation of ETX values between each node, as opposed to working with the ETX average along the route. This method ensures a better routing performance in dense sensor networks. The simulations are done through the Cooja simulator, based on the Contiki operating system. The simulations showed that the proposed optimization outperforms at a high margin in both OF0 and MRHOF, in terms of network latency, packet delivery ratio, lifetime, and power consumption.

  5. Utilizing Joint Routing and Capacity Assignment Algorithms to Achieve Inter- and Intra-Group Delay Fairness in Multi-Rate Multicast Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Yean-Fu Wen

    2013-03-01

    Full Text Available Recent advance in wireless sensor network (WSN applications such as the Internet of Things (IoT have attracted a lot of attention. Sensor nodes have to monitor and cooperatively pass their data, such as temperature, sound, pressure, etc. through the network under constrained physical or environmental conditions. The Quality of Service (QoS is very sensitive to network delays. When resources are constrained and when the number of receivers increases rapidly, how the sensor network can provide good QoS (measured as end-to-end delay becomes a very critical problem. In this paper; a solution to the wireless sensor network multicasting problem is proposed in which a mathematical model that provides services to accommodate delay fairness for each subscriber is constructed. Granting equal consideration to both network link capacity assignment and routing strategies for each multicast group guarantees the intra-group and inter-group delay fairness of end-to-end delay. Minimizing delay and achieving fairness is ultimately achieved through the Lagrangean Relaxation method and Subgradient Optimization Technique. Test results indicate that the new system runs with greater effectiveness and efficiency.

  6. Utilizing joint routing and capacity assignment algorithms to achieve inter- and intra-group delay fairness in multi-rate multicast wireless sensor networks.

    Science.gov (United States)

    Lin, Frank Yeong-Sung; Hsiao, Chiu-Han; Lin, Leo Shih-Chang; Wen, Yean-Fu

    2013-03-14

    Recent advance in wireless sensor network (WSN) applications such as the Internet of Things (IoT) have attracted a lot of attention. Sensor nodes have to monitor and cooperatively pass their data, such as temperature, sound, pressure, etc. through the network under constrained physical or environmental conditions. The Quality of Service (QoS) is very sensitive to network delays. When resources are constrained and when the number of receivers increases rapidly, how the sensor network can provide good QoS (measured as end-to-end delay) becomes a very critical problem. In this paper; a solution to the wireless sensor network multicasting problem is proposed in which a mathematical model that provides services to accommodate delay fairness for each subscriber is constructed. Granting equal consideration to both network link capacity assignment and routing strategies for each multicast group guarantees the intra-group and inter-group delay fairness of end-to-end delay. Minimizing delay and achieving fairness is ultimately achieved through the Lagrangean Relaxation method and Subgradient Optimization Technique. Test results indicate that the new system runs with greater effectiveness and efficiency.

  7. Bellman Ford algorithm - in Routing Information Protocol (RIP)

    Science.gov (United States)

    Krianto Sulaiman, Oris; Mahmud Siregar, Amir; Nasution, Khairuddin; Haramaini, Tasliyah

    2018-04-01

    In a large scale network need a routing that can handle a lot number of users, one of the solutions to cope with large scale network is by using a routing protocol, There are 2 types of routing protocol that is static and dynamic, Static routing is manually route input based on network admin, while dynamic routing is automatically route input formed based on existing network. Dynamic routing is efficient used to network extensively because of the input of route automatic formed, Routing Information Protocol (RIP) is one of dynamic routing that uses the bellman-ford algorithm where this algorithm will search for the best path that traversed the network by leveraging the value of each link, so with the bellman-ford algorithm owned by RIP can optimize existing networks.

  8. Multicast middleware for performance and topology analysis of multimedia grids

    Directory of Open Access Journals (Sweden)

    Jerry Z. Xie

    2017-04-01

    Full Text Available Since multicast reduces bandwidth consumption in multimedia grid computing, the middleware for monitoring the performance and topology of multicast communications is important to the design and management of multimedia grid applications. However, the current middleware technologies for multicast performance monitoring are still far from attaining the level of maturity and there lacks consistent approaches to obtain the evaluation data for multicast. In this study, to serve a clear guide for the design and implementation of the multicast middleware, two algorithms are developed for organising all constituents in multicast communications and analysing the multicast performance in two topologies – ‘multicast distribution tree’ and ‘clusters distribution’, and a definitive set of corresponding metrics that are comprehensive yet viable for evaluating multicast communications are also presented. Instead of using the inference data from unicast measurements, in the proposed middleware, the measuring data of multicast traffic are obtained directly from multicast protocols in real time. Moreover, this study makes a middleware implementation which is integrated into a real access grid multicast communication infrastructure. The results of the implementation demonstrate the substantial improvements in the accuracy and real time in evaluating the performance and topology of multicast network.

  9. Intelligent routing protocol for ad hoc wireless network

    Science.gov (United States)

    Peng, Chaorong; Chen, Chang Wen

    2006-05-01

    A novel routing scheme for mobile ad hoc networks (MANETs), which combines hybrid and multi-inter-routing path properties with a distributed topology discovery route mechanism using control agents is proposed in this paper. In recent years, a variety of hybrid routing protocols for Mobile Ad hoc wireless networks (MANETs) have been developed. Which is proactively maintains routing information for a local neighborhood, while reactively acquiring routes to destinations beyond the global. The hybrid protocol reduces routing discovery latency and the end-to-end delay by providing high connectivity without requiring much of the scarce network capacity. On the other side the hybrid routing protocols in MANETs likes Zone Routing Protocol still need route "re-discover" time when a route between zones link break. Sine the topology update information needs to be broadcast routing request on local zone. Due to this delay, the routing protocol may not be applicable for real-time data and multimedia communication. We utilize the advantages of a clustering organization and multi-routing path in routing protocol to achieve several goals at the same time. Firstly, IRP efficiently saves network bandwidth and reduces route reconstruction time when a routing path fails. The IRP protocol does not require global periodic routing advertisements, local control agents will automatically monitor and repair broke links. Secondly, it efficiently reduces congestion and traffic "bottlenecks" for ClusterHeads in clustering network. Thirdly, it reduces significant overheads associated with maintaining clusters. Fourthly, it improves clusters stability due to dynamic topology changing frequently. In this paper, we present the Intelligent Routing Protocol. First, we discuss the problem of routing in ad hoc networks and the motivation of IRP. We describe the hierarchical architecture of IRP. We describe the routing process and illustrate it with an example. Further, we describe the control manage

  10. PVM and IP multicast

    Energy Technology Data Exchange (ETDEWEB)

    Dunigan, T.H.; Hall, K.A.

    1996-12-01

    This report describes a 1994 demonstration implementation of PVM that uses IP multicast. PVM`s one-to-many unicast implementation of its pvm{_}mcast() function is replaced with reliable IP multicast. Performance of PVM using IP multicast over local and wide-area networks is measured and compared with the original unicast implementation. Current limitations of IP multicast are noted.

  11. RSRP: A Robust Secure Routing Protocol in MANET

    Directory of Open Access Journals (Sweden)

    Sinha Ditipriya

    2014-05-01

    Full Text Available In this paper, we propose a novel algorithm RSRP to build a robust secure routing protocol in mobile ad-hoc networks (MANETs. This algorithm is based on some basic schemes such as RSA_CRT for encryption and decryption of messages; CRT for safety key generation, Shamir’s secret sharing principle for generation of secure routes. Those routes which are free from any malicious node and which belong to the set of disjoint routes between a source-destination pair are considered as probable routes. Shamir’s secret sharing principle is applied on those probable routes to obtain secure routes. Finally, most trustworthy and stable route is selected among those secure routes. Selection of the final route depends on some criteria of the nodes present in a route e.g.: battery power, mobility and trust value. In addition, complexity of key generation is reduced to a large extent by using RSA-CRT instead of RSA. In turn, the routing becomes less expensive and most secure and robust one. Performance of this routing protocol is then compared with non-secure routing protocols (AODV and DSR, secure routing scheme using secret sharing, security routing protocol using ZRP and SEAD depending on basic characteristics of these protocols. All such comparisons show that RSRP shows better performance in terms of computational cost, end-to-end delay and packet dropping in presence of malicious nodes in the MANET, keeping the overhead in terms of control packets same as other secure routing protocols.

  12. Multisites Coordination in Shared Multicast Trees

    National Research Council Canada - National Science Library

    Dommel, H-P; Garcia-Luna-Aceves, J. J

    1999-01-01

    .... The protocol supports Internet-wide coordination for large and highly interactive groupwork, relying on transmission of coordination directives between group members across a shared end-to-end multicast tree...

  13. Routing protocol extension for resilient GMPLS multi-domain networks

    DEFF Research Database (Denmark)

    Manolova, Anna Vasileva; Ruepp, Sarah Renée; Romeral, Ricardo

    2010-01-01

    This paper evaluates the performance of multi-domain networks under the Generalized Multi-Protocol Label Switching control framework in case of a single inter-domain link failure. We propose and evaluate a routing protocol extension for the Border Gateway Protocol, which allows domains to obtain...... two Autonomous System disjoint paths and use them efficiently under failure conditions. Three main applications for the protocol extension are illustrated: reducing traffic loss on existing connections by xploiting pre-selected backup paths derived with our proposal, applying multi-domain restoration...... as survivability mechanism in case of single link failure, and employing proper failure notification mechanisms for routing of future connection requests under routing protocol re-convergence. Via simulations we illustrate the benefits of utilizing the proposed routing protocol extension for networks employing...

  14. A Survey of Routing Protocols in Wireless Body Sensor Networks

    Science.gov (United States)

    Bangash, Javed Iqbal; Abdullah, Abdul Hanan; Anisi, Mohammad Hossein; Khan, Abdul Waheed

    2014-01-01

    Wireless Body Sensor Networks (WBSNs) constitute a subset of Wireless Sensor Networks (WSNs) responsible for monitoring vital sign-related data of patients and accordingly route this data towards a sink. In routing sensed data towards sinks, WBSNs face some of the same routing challenges as general WSNs, but the unique requirements of WBSNs impose some more constraints that need to be addressed by the routing mechanisms. This paper identifies various issues and challenges in pursuit of effective routing in WBSNs. Furthermore, it provides a detailed literature review of the various existing routing protocols used in the WBSN domain by discussing their strengths and weaknesses. PMID:24419163

  15. Analyzing the effect of routing protocols on media access control protocols in radio networks

    Energy Technology Data Exchange (ETDEWEB)

    Barrett, C. L. (Christopher L.); Drozda, M. (Martin); Marathe, A. (Achla); Marathe, M. V. (Madhav V.)

    2002-01-01

    We study the effect of routing protocols on the performance of media access control (MAC) protocols in wireless radio networks. Three well known MAC protocols: 802.11, CSMA, and MACA are considered. Similarly three recently proposed routing protocols: AODV, DSR and LAR scheme 1 are considered. The experimental analysis was carried out using GloMoSim: a tool for simulating wireless networks. The main focus of our experiments was to study how the routing protocols affect the performance of the MAC protocols when the underlying network and traffic parameters are varied. The performance of the protocols was measured w.r.t. five important parameters: (i) number of received packets, (ii) average latency of each packet, (iii) throughput (iv) long term fairness and (v) number of control packets at the MAC layer level. Our results show that combinations of routing and MAC protocols yield varying performance under varying network topology and traffic situations. The result has an important implication; no combination of routing protocol and MAC protocol is the best over all situations. Also, the performance analysis of protocols at a given level in the protocol stack needs to be studied not locally in isolation but as a part of the complete protocol stack. A novel aspect of our work is the use of statistical technique, ANOVA (Analysis of Variance) to characterize the effect of routing protocols on MAC protocols. This technique is of independent interest and can be utilized in several other simulation and empirical studies.

  16. Routing Protocols for Underwater Wireless Sensor Networks: Taxonomy, Research Challenges, Routing Strategies and Future Directions.

    Science.gov (United States)

    Khan, Anwar; Ali, Ihsan; Ghani, Abdullah; Khan, Nawsher; Alsaqer, Mohammed; Rahman, Atiq Ur; Mahmood, Hasan

    2018-05-18

    Recent research in underwater wireless sensor networks (UWSNs) has gained the attention of researchers in academia and industry for a number of applications. They include disaster and earthquake prediction, water quality and environment monitoring, leakage and mine detection, military surveillance and underwater navigation. However, the aquatic medium is associated with a number of limitations and challenges: long multipath delay, high interference and noise, harsh environment, low bandwidth and limited battery life of the sensor nodes. These challenges demand research techniques and strategies to be overcome in an efficient and effective fashion. The design of routing protocols for UWSNs is one of the promising solutions to cope with these challenges. This paper presents a survey of the routing protocols for UWSNs. For the ease of description, the addressed routing protocols are classified into two groups: localization-based and localization-free protocols. These groups are further subdivided according to the problems they address or the major parameters they consider during routing. Unlike the existing surveys, this survey considers only the latest and state-of-the-art routing protocols. In addition, every protocol is described in terms of its routing strategy and the problem it addresses and solves. The merit(s) of each protocol is (are) highlighted along with the cost. A description of the protocols in this fashion has a number of advantages for researchers, as compared to the existing surveys. Firstly, the description of the routing strategy of each protocol makes its routing operation easily understandable. Secondly, the demerit(s) of a protocol provides (provide) insight into overcoming its flaw(s) in future investigation. This, in turn, leads to the foundation of new protocols that are more intelligent, robust and efficient with respect to the desired parameters. Thirdly, a protocol can be selected for the appropriate application based on its described

  17. Perancangan dan Analisis Redistribution Routing Protocol OSPF dan EIGRP

    Directory of Open Access Journals (Sweden)

    DWI ARYANTA

    2014-07-01

    OSPF (Open Shortest Path First and EIGRP (Enhanced Interior Gateway Routing Protocol are two routing protocols are widely used in computer networks. Differences between the characteristics of routing protocols pose a problem in the delivery of data packets. Redistribution technique is the solution for communication between routing protocols. By using the software Cisco Packet Tracer 5.3 in this study were made simulating OSPF and EIGRP redistribution linked by technique, then compared its quality with a single EIGRP and OSPF routing protocols. Testing parameters in this study is the value of the time delay and trace route. Value trace route based on direct calculation of cost and metric compared with the simulation results. The result can be OSPF and EIGRP redistribution process. Value delay redistribution 1% better than OSPF and EIGRP 2-3% under traffic density dependent. In calculating the trace route redistribution is done 2 calculations, the cost for OSPF area and the area of the EIGRP metric. Making primary and alternate paths based on the packet delivery rate and the cost of the smallest metric, it is proved by calculation and simulation. Keywords: OSPF, EIGRP, Redistribution, Delay, Cost, Metric.

  18. Enhanced DSR Routing Protocol for the Short Time Disconnected MANET

    Directory of Open Access Journals (Sweden)

    PAPAJ Ján

    2013-05-01

    Full Text Available Data delivery in Mobile Ad-Hoc network (MANET is a very difficult task due to the fact the sporadic connections between mobile nodes. For this reason, we introduce the new modified routing protocol that enables the data delivery in the case that the connections are disconnected. A key aspect of the protocol is a process of finding connections between source and destination nodes that can provide low end-to-end delay and better delivery performance in a disconnected MANET. The protocol provides the concepts of opportunistic routing of the routing packets in disconnected MANETs. In this paper we present a modification of the DSR routing protocol and also some results of a simulation.

  19. Perancangan dan Analisis Redistribution Routing Protocol OSPF dan EIGRP

    Directory of Open Access Journals (Sweden)

    DWI ARYANTA

    2016-02-01

    Full Text Available Abstrak OSPF (Open Shortest Path First dan EIGRP (Enhanced Interior Gateway Routing Protocol adalah dua routing protokol yang banyak digunakan dalam jaringan komputer. Perbedaan karakteristik antar routing protokol menimbulkan masalah dalam pengiriman paket data. Teknik redistribution adalah solusi untuk melakukan komunikasi antar routing protokol. Dengan menggunakan software Cisco Packet Tracer 5.3 pada penelitian ini dibuat simulasi OSPF dan EIGRP yang dihubungkan oleh teknik redistribution, kemudian dibandingkan kualitasnya dengan single routing protokol EIGRP dan OSPF. Parameter pengujian dalam penelitian ini adalah nilai time delay dan trace route. Nilai trace route berdasarkan perhitungan langsung cost dan metric dibandingkan dengan hasil simulasi. Hasilnya dapat dilakukan proses redistribution OSPF dan EIGRP. Nilai delay redistribution lebih baik 1% dibanding OSPF dan 2-3% di bawah EIGRP tergantung kepadatan traffic. Dalam perhitungan trace route redistribution dilakukan 2 perhitungan, yaitu cost untuk area OSPF dan metric pada area EIGRP. Pengambilan jalur utama dan alternatif pengiriman paket berdasarkan nilai cost dan metric yang terkecil, hal ini terbukti berdasarkan perhitungan dan simulasi. Kata kunci: OSPF, EIGRP, Redistribution, Delay, Cost, Metric. Abstract OSPF (Open Shortest Path First and EIGRP (Enhanced Interior Gateway Routing Protocol are two routing protocols are widely used in computer networks. Differences between the characteristics of routing protocols pose a problem in the delivery of data packets. Redistribution technique is the solution for communication between routing protocols. By using the software Cisco Packet Tracer 5.3 in this study were made simulating OSPF and EIGRP redistribution linked by technique, then compared its quality with a single EIGRP and OSPF routing protocols. Testing parameters in this study is the value of the time delay and trace route. Value trace route based on direct calculation of cost

  20. Cluster Based Hierarchical Routing Protocol for Wireless Sensor Network

    OpenAIRE

    Rashed, Md. Golam; Kabir, M. Hasnat; Rahim, Muhammad Sajjadur; Ullah, Shaikh Enayet

    2012-01-01

    The efficient use of energy source in a sensor node is most desirable criteria for prolong the life time of wireless sensor network. In this paper, we propose a two layer hierarchical routing protocol called Cluster Based Hierarchical Routing Protocol (CBHRP). We introduce a new concept called head-set, consists of one active cluster head and some other associate cluster heads within a cluster. The head-set members are responsible for control and management of the network. Results show that t...

  1. A tree routing protocol for cognitive radio network

    Directory of Open Access Journals (Sweden)

    Mohammed Hashem

    2017-07-01

    Full Text Available Cognitive Radio (CR technology is an agile solution for spectrum congestion and spectrum access utilization problems that result from the legacy fixed spectrum management policies. CR technology can exploit unused licensed band to meet the increasing demand for radio frequency. The routing process faces many challenges in CR Network (CRN such as the absence of centralized infrastructure, the coordination between the routing module and spectrum management module, in addition to the frequent link failure due to the sudden appearance of PUs. In this paper we propose a Tree routing protocol for cognitive radio network (C-TRP that jointly utilizes the tree routing algorithm with a spectrum management module in routing decisions, and also we proposed a new metric used in taking the best route decisions. In addition, we enhance the traditional tree routing algorithm by using a neighbor table technique that speeds up the forwarding data packets. Moreover, we add a robust recovery module to C-TRP to resume the network in case of the link failure. The main motivation in the design of C-TRP is quick data transmission and maximization of date rates. The performance evaluation is carried out in NS2 simulator. The simulation results proved that C-TRP protocol achieves better performance in terms of average “PDR”, “end-to-end delay” and “routing overhead ratio “compared to “CTBR” and “STOD-RP” routing protocols.

  2. Performance analysis of routing protocols for IoT

    Science.gov (United States)

    Manda, Sridhar; Nalini, N.

    2018-04-01

    Internet of Things (IoT) is an arrangement of advancements that are between disciplinary. It is utilized to have compelling combination of both physical and computerized things. With IoT physical things can have personal virtual identities and participate in distributed computing. Realization of IoT needs the usage of sensors based on the sector for which IoT is integrated. For instance, in healthcare domain, IoT needs to have integration with wearable sensors used by patients. As sensor devices produce huge amount of data, often called big data, there should be efficient routing protocols in place. To the extent remote systems is worried there are some current protocols, for example, OLSR, DSR and AODV. It additionally tosses light into Trust based routing protocol for low-power and lossy systems (TRPL) for IoT. These are broadly utilized remote directing protocols. As IoT is developing round the corner, it is basic to investigate routing protocols that and evaluate their execution regarding throughput, end to end delay, and directing overhead. The execution experiences can help in settling on very much educated choices while incorporating remote systems with IoT. In this paper, we analyzed different routing protocols and their performance is compared. It is found that AODV showed better performance than other routing protocols aforementioned.

  3. An Improved 6LoWPAN Hierarchical Routing Protocol

    Directory of Open Access Journals (Sweden)

    Xue Li

    2015-10-01

    Full Text Available IETF 6LoWPAN working group is engaged in the IPv6 protocol stack research work based on IEEE802.15.4 standard. In this working group, the routing protocol is one of the important research contents. In the 6LoWPAN, HiLow is a well-known layered routing protocol. This paper puts forward an improved hierarchical routing protocol GHiLow by improving HiLow parent node selection and path restoration strategy. GHiLow improves the parent node selection by increasing the choice of parameters. Simutaneously, it also improves path recovery by analysing different situations to recovery path. Therefore, GHiLow contributes to the ehancement of network performance and the decrease of network energy consumption.

  4. Evaluation of svr: a wireless sensor network routing protocol

    International Nuclear Information System (INIS)

    Baloch, J.; Khanzada, T.J.S.

    2014-01-01

    The advancement in technology has made it possible to create small in size, low cost sensor nodes. However, the small size and low cost of such nodes comesat at price that is, reduced processing power, low memory and significantly small battery energy storage. WSNs (Wireless Sensor Networks) are inherently ad hoc in nature and are assumed to work in the toughest terrain. The network lifetime plays a pivotal role in a wireless sensor network. A long network lifetime, could be achieved by either making significant changes in these low cost devices, which is not a feasible solution or by improving the means of communication throughout the network. The communication in such networks could be improved by employing energy efficient routing protocols, to route the data throughout the network. In this paper the SVR (Spatial Vector Routing) protocol is compared against the most common WSN routing protocols, and from the results it could be inferred that the SVR protocol out performs its counterparts. The protocol provides an energy efficient means of communication in the network. (author)

  5. Application Layer Multicast

    Science.gov (United States)

    Allani, Mouna; Garbinato, Benoît; Pedone, Fernando

    An increasing number of Peer-to-Peer (P2P) Internet applications rely today on data dissemination as their cornerstone, e.g., audio or video streaming, multi-party games. These applications typically depend on some support for multicast communication, where peers interested in a given data stream can join a corresponding multicast group. As a consequence, the efficiency, scalability, and reliability guarantees of these applications are tightly coupled with that of the underlying multicast mechanism.

  6. A security analysis of the 802.11s wireless mesh network routing protocol and its secure routing protocols.

    Science.gov (United States)

    Tan, Whye Kit; Lee, Sang-Gon; Lam, Jun Huy; Yoo, Seong-Moo

    2013-09-02

    Wireless mesh networks (WMNs) can act as a scalable backbone by connecting separate sensor networks and even by connecting WMNs to a wired network. The Hybrid Wireless Mesh Protocol (HWMP) is the default routing protocol for the 802.11s WMN. The routing protocol is one of the most important parts of the network, and it requires protection, especially in the wireless environment. The existing security protocols, such as the Broadcast Integrity Protocol (BIP), Counter with cipher block chaining message authentication code protocol (CCMP), Secure Hybrid Wireless Mesh Protocol (SHWMP), Identity Based Cryptography HWMP (IBC-HWMP), Elliptic Curve Digital Signature Algorithm HWMP (ECDSA-HWMP), and Watchdog-HWMP aim to protect the HWMP frames. In this paper, we have analyzed the vulnerabilities of the HWMP and developed security requirements to protect these identified vulnerabilities. We applied the security requirements to analyze the existing secure schemes for HWMP. The results of our analysis indicate that none of these protocols is able to satisfy all of the security requirements. We also present a quantitative complexity comparison among the protocols and an example of a security scheme for HWMP to demonstrate how the result of our research can be utilized. Our research results thus provide a tool for designing secure schemes for the HWMP.

  7. Analysis of Pervasive Mobile Ad Hoc Routing Protocols

    Science.gov (United States)

    Qadri, Nadia N.; Liotta, Antonio

    Mobile ad hoc networks (MANETs) are a fundamental element of pervasive networks and therefore, of pervasive systems that truly support pervasive computing, where user can communicate anywhere, anytime and on-the-fly. In fact, future advances in pervasive computing rely on advancements in mobile communication, which includes both infrastructure-based wireless networks and non-infrastructure-based MANETs. MANETs introduce a new communication paradigm, which does not require a fixed infrastructure - they rely on wireless terminals for routing and transport services. Due to highly dynamic topology, absence of established infrastructure for centralized administration, bandwidth constrained wireless links, and limited resources in MANETs, it is challenging to design an efficient and reliable routing protocol. This chapter reviews the key studies carried out so far on the performance of mobile ad hoc routing protocols. We discuss performance issues and metrics required for the evaluation of ad hoc routing protocols. This leads to a survey of existing work, which captures the performance of ad hoc routing algorithms and their behaviour from different perspectives and highlights avenues for future research.

  8. Energy Aware GPSR Routing Protocol in a Wireless Sensor Network ...

    African Journals Online (AJOL)

    Energy is the scarce resource in wireless sensor networks (WSNs), and it determines the lifetime of WSNs. For this reason, WSN algorithms and routing protocols should be selected in a manner which fulfills these energy requirements. This paper presents a solution to increase the lifetime of WSNs by decreasing their ...

  9. Reliable multicast for the Grid: a case study in experimental computer science.

    Science.gov (United States)

    Nekovee, Maziar; Barcellos, Marinho P; Daw, Michael

    2005-08-15

    In its simplest form, multicast communication is the process of sending data packets from a source to multiple destinations in the same logical multicast group. IP multicast allows the efficient transport of data through wide-area networks, and its potentially great value for the Grid has been highlighted recently by a number of research groups. In this paper, we focus on the use of IP multicast in Grid applications, which require high-throughput reliable multicast. These include Grid-enabled computational steering and collaborative visualization applications, and wide-area distributed computing. We describe the results of our extensive evaluation studies of state-of-the-art reliable-multicast protocols, which were performed on the UK's high-speed academic networks. Based on these studies, we examine the ability of current reliable multicast technology to meet the Grid's requirements and discuss future directions.

  10. Performance modeling of neighbor discovery in proactive routing protocols

    Directory of Open Access Journals (Sweden)

    Andres Medina

    2011-07-01

    Full Text Available It is well known that neighbor discovery is a critical component of proactive routing protocols in wireless ad hoc networks. However there is no formal study on the performance of proposed neighbor discovery mechanisms. This paper provides a detailed model of key performance metrics of neighbor discovery algorithms, such as node degree and the distribution of the distance to symmetric neighbors. The model accounts for the dynamics of neighbor discovery as well as node density, mobility, radio and interference. The paper demonstrates a method for applying these models to the evaluation of global network metrics. In particular, it describes a model of network connectivity. Validation of the models shows that the degree estimate agrees, within 5% error, with simulations for the considered scenarios. The work presented in this paper serves as a basis for the performance evaluation of remaining performance metrics of routing protocols, vital for large scale deployment of ad hoc networks.

  11. Congestion control for vehicular delay tolerant network routing protocols

    OpenAIRE

    Oham, Chuka Finbars

    2014-01-01

    The Vehicular Delay Tolerant Network (VDTN) is a special and challenging type of the Delay Tolerant Network because of its high mobility, frequent disconnections and nodal congestion features. These challenging features make it prone to congestion which leads to a considerable amount of message drops in the network. To minimize the impact of congestion in the network, we designed and implemented the Congestion Aware Spray and Wait (CASaW) routing protocol. We varied the buffer sizes of the no...

  12. Cluster chain based energy efficient routing protocol for moblie WSN

    Directory of Open Access Journals (Sweden)

    WU Ziyu

    2016-04-01

    Full Text Available With the ubiquitous smart devices acting as mobile sensor nodes in the wireless sensor networks(WSNs to sense and transmit physical information,routing protocols should be designed to accommodate the mobility issues,in addition to conventional considerations on energy efficiency.However,due to frequent topology change,traditional routing schemes cannot perform well.Moreover,existence of mobile nodes poses new challenges on energy dissipation and packet loss.In this paper,a novel routing scheme called cluster chain based routing protocol(CCBRP is proposed,which employs a combination of cluster and chain structure to accomplish data collection and transmission and thereafter selects qualified cluster heads as chain leaders to transmit data to the sink.Furthermore,node mobility is handled based on periodical membership update of mobile nodes.Simulation results demonstrate that CCBRP has a good performance in terms of network lifetime and packet delivery,also strikes a better balance between successful packet reception and energy consumption.

  13. Routing Protocol for Mobile Ad-hoc Wireless Networks

    Directory of Open Access Journals (Sweden)

    I. M. B. Nogales

    2007-09-01

    Full Text Available Bluetooth is a cutting-edge technology used for implementing wireless ad hoc networks. In order to provide an overall scheme for mobile ad hoc networks, this paper deals with scatternet topology formation and routing algorithm to form larger ad hoc wireless Networks. Scatternet topology starts by forming a robust network, which is less susceptible to the problems posed by node mobility. Mobile topology relies on the presence of free nodes that create multiple connections with the network and on their subsequently rejoining the network. Our routing protocol is a proactive routing protocol, which is tailor made for the Bluetooth ad hoc network. The connection establishment connects nodes in a structure that simplifies packet routing and scheduling. The design allows nodes to arrive and leave arbitrarily, incrementally building the topology and healing partitions when they occur. We present simulation results that show that the algorithm presents low formation latency and also generates an efficient topology for forwarding packets along ad-hoc wireless networks.

  14. Construction of Light-trees for WDM Multicasting under Splitting Capability Constraints

    DEFF Research Database (Denmark)

    Zsigri, Anikó; Guitton, A.; Molnár, M.

    2003-01-01

    Communication systems with all-optical multicasting have better performance than those using optical/electrical/optical conversion. Multicast protocols assume that all nodes in the network can forward the signal from one input to several outputs. Since fabrication of an optical switch with splitt......Communication systems with all-optical multicasting have better performance than those using optical/electrical/optical conversion. Multicast protocols assume that all nodes in the network can forward the signal from one input to several outputs. Since fabrication of an optical switch...

  15. Mobile Multicast in Hierarchical Proxy Mobile IPV6

    Science.gov (United States)

    Hafizah Mohd Aman, Azana; Hashim, Aisha Hassan A.; Mustafa, Amin; Abdullah, Khaizuran

    2013-12-01

    Mobile Internet Protocol Version 6 (MIPv6) environments have been developing very rapidly. Many challenges arise with the fast progress of MIPv6 technologies and its environment. Therefore the importance of improving the existing architecture and operations increases. One of the many challenges which need to be addressed is the need for performance improvement to support mobile multicast. Numerous approaches have been proposed to improve mobile multicast performance. This includes Context Transfer Protocol (CXTP), Hierarchical Mobile IPv6 (HMIPv6), Fast Mobile IPv6 (FMIPv6) and Proxy Mobile IPv6 (PMIPv6). This document describes multicast context transfer in hierarchical proxy mobile IPv6 (H-PMIPv6) to provide better multicasting performance in PMIPv6 domain.

  16. A Secure Cluster-Based Multipath Routing Protocol for WMSNs

    Directory of Open Access Journals (Sweden)

    Jamal N. Al-Karaki

    2011-04-01

    Full Text Available The new characteristics of Wireless Multimedia Sensor Network (WMSN and its design issues brought by handling different traffic classes of multimedia content (video streams, audio, and still images as well as scalar data over the network, make the proposed routing protocols for typical WSNs not directly applicable for WMSNs. Handling real-time multimedia data requires both energy efficiency and QoS assurance in order to ensure efficient utility of different capabilities of sensor resources and correct delivery of collected information. In this paper, we propose a Secure Cluster-based Multipath Routing protocol for WMSNs, SCMR, to satisfy the requirements of delivering different data types and support high data rate multimedia traffic. SCMR exploits the hierarchical structure of powerful cluster heads and the optimized multiple paths to support timeliness and reliable high data rate multimedia communication with minimum energy dissipation. Also, we present a light-weight distributed security mechanism of key management in order to secure the communication between sensor nodes and protect the network against different types of attacks. Performance evaluation from simulation results demonstrates a significant performance improvement comparing with existing protocols (which do not even provide any kind of security feature in terms of average end-to-end delay, network throughput, packet delivery ratio, and energy consumption.

  17. A SURVEY on WIRELESS MESH NETWORKS, ROUTING METRICS and PROTOCOLS

    Directory of Open Access Journals (Sweden)

    Safak DURUKAN ODABASI

    2013-01-01

    Full Text Available Today, Internet has become an indispensable part of our daily lives. It has a growing user community in many fields from banking transactions to online entertainment. It will be very efficient for users, as the next generation internet access becomes wireless like frequently used services such as cellular phones. But for providing this, a new network is needed to be designed or an existing network must be improved as well as making changes on infrastructure. At this point, mesh network infrastructure arises and offers more sophisticated internet access with less need. The most important advantage of mesh networks is the capability of working without infrastructure. Mesh networks are an additional access technology more than being a renewed one in the next generation wireless networks called 4G. In this study, wireless mesh networks and example applications are mentioned. Base architecture and design factors are emphasized, current routing protocols that are used on wireless mesh networks and routing metrics on which these protocols are based, are explained. Finally, the performance effects of these protocols and metrics on different network topologies are referred.

  18. Maximization Network Throughput Based on Improved Genetic Algorithm and Network Coding for Optical Multicast Networks

    Science.gov (United States)

    Wei, Chengying; Xiong, Cuilian; Liu, Huanlin

    2017-12-01

    Maximal multicast stream algorithm based on network coding (NC) can improve the network's throughput for wavelength-division multiplexing (WDM) networks, which however is far less than the network's maximal throughput in terms of theory. And the existing multicast stream algorithms do not give the information distribution pattern and routing in the meantime. In the paper, an improved genetic algorithm is brought forward to maximize the optical multicast throughput by NC and to determine the multicast stream distribution by hybrid chromosomes construction for multicast with single source and multiple destinations. The proposed hybrid chromosomes are constructed by the binary chromosomes and integer chromosomes, while the binary chromosomes represent optical multicast routing and the integer chromosomes indicate the multicast stream distribution. A fitness function is designed to guarantee that each destination can receive the maximum number of decoding multicast streams. The simulation results showed that the proposed method is far superior over the typical maximal multicast stream algorithms based on NC in terms of network throughput in WDM networks.

  19. Comparison of MANET Routing Protocols in Different Traffic and Mobility Models

    Directory of Open Access Journals (Sweden)

    J. Baraković

    2010-06-01

    Full Text Available Routing protocol election in MANET (Mobile Ad Hoc Network is a great challenge, because of its frequent topology changes and routing overhead. This paper compares performances of three routing protocols: Destination Sequenced Distance Vector (DSDV, Ad Hoc Ondemand Distance Vector (AODV and Dynamic Source Routing (DSR, based on results analysis obtained using simulations with different load and mobility scenarios performed with Network Simulator version 2 (NS-2. In low load and low mobility scenarios routing protocols perform in a similar manner. However, with mobility and load increasing DSR outperforms AODV and DSDV protocols.

  20. A two-hop based adaptive routing protocol for real-time wireless sensor networks.

    Science.gov (United States)

    Rachamalla, Sandhya; Kancherla, Anitha Sheela

    2016-01-01

    One of the most important and challenging issues in wireless sensor networks (WSNs) is to optimally manage the limited energy of nodes without degrading the routing efficiency. In this paper, we propose an energy-efficient adaptive routing mechanism for WSNs, which saves energy of nodes by removing the much delayed packets without degrading the real-time performance of the used routing protocol. It uses the adaptive transmission power algorithm which is based on the attenuation of the wireless link to improve the energy efficiency. The proposed routing mechanism can be associated with any geographic routing protocol and its performance is evaluated by integrating with the well known two-hop based real-time routing protocol, PATH and the resulting protocol is energy-efficient adaptive routing protocol (EE-ARP). The EE-ARP performs well in terms of energy consumption, deadline miss ratio, packet drop and end-to-end delay.

  1. Key Management for Secure Multicast over IPv6 Wireless Networks

    Directory of Open Access Journals (Sweden)

    Siddiqi Mohammad Umar

    2006-01-01

    Full Text Available Multicasting is an efficient method for transmission and routing of packets to multiple destinations using fewer network resources. Along with widespread deployment of wireless networks, secure multicast over wireless networks is an important and challenging goal. In this paper, we extend the scope of a recent new key distribution scheme to a security framework that offers a novel solution for secure multicast over IPv6 wireless networks. Our key management framework includes two scenarios for securely distributing the group key and rekey messages for joining and leaving a mobile host in secure multicast group. In addition, we perform the security analysis and provide performance comparisons between our approach and two recently published scenarios. The benefits of our proposed techniques are that they minimize the number of transmissions required to rekey the multicast group and impose minimal storage requirements on the multicast group. In addition, our proposed schemes are also very desirable from the viewpoint of transmission bandwidth savings since an efficient rekeying mechanism is provided for membership changes and they significantly reduce the required bandwidth due to key updating in mobile networks. Moreover, they achieve the security and scalability requirements in wireless networks.

  2. Performance evaluation of spatial vector routing protocol for wireless sensor networks

    International Nuclear Information System (INIS)

    Baloch, J.; Jokhio, I.

    2012-01-01

    WSNs (Wireless Sensor Networks) is an emerging area of research. Researchers worldwide are working on the issues faced by sensor nodes. Communication has been a major issue in wireless networks and the problem is manifolds in WSN s because of the limited resources. The routing protocol in such networks plays a pivotal role, as an effective routing protocol could significantly reduce the energy consumed in transmitting and receiving data packets throughout a network. In this paper the performance of SVR (Spatial Vector Routing) an energy efficient, location aware routing protocol is compared with the existing location aware protocols. The results from the simulation trials show the performance of SVR. (author)

  3. Performance Evaluation of Spatial Vector Routing Protocol for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Javed Ali Baloch

    2012-10-01

    Full Text Available WSNs (Wireless Sensor Networks is an emerging area of research. Researchers worldwide are working on the issues faced by sensor nodes. Communication has been a major issue in wireless networks and the problem is manifolds in WSNs because of the limited resources. The routing protocol in such networks plays a pivotal role, as an effective routing protocol could significantly reduce the energy consumed in transmitting and receiving data packets throughout a network. In this paper the performance of SVR (Spatial Vector Routing an energy efficient, location aware routing protocol is compared with the existing location aware protocols. The results from the simulation trials show the performance of SVR.

  4. Energy-Aware Routing Protocol for Ad Hoc Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Mann Raminder P

    2005-01-01

    Full Text Available Wireless ad hoc sensor networks differ from wireless ad hoc networks from the following perspectives: low energy, lightweight routing protocols, and adaptive communication patterns. This paper proposes an energy-aware routing protocol (EARP suitable for ad hoc wireless sensor networks and presents an analysis for its energy consumption in various phases of route discovery and maintenance. Based on the energy consumption associated with route request processing, EARP advocates the minimization of route requests by allocating dynamic route expiry times. This paper introduces a unique mechanism for estimation of route expiry time based on the probability of route validity, which is a function of time, number of hops, and mobility parameters. In contrast to AODV, EARP reduces the repeated flooding of route requests by maintaining valid routes for longer durations.

  5. Towards designing energy-efficient routing protocol for wireless mesh networks

    CSIR Research Space (South Africa)

    Dludla, AG

    2009-08-01

    Full Text Available Different studies have proposed number of routing protocols to overcome data transmission challenges. Very few of these protocols consider node energy. In this study, the state of art work from various studies is reviewed and compared based...

  6. Cost analysis of hybrid adaptive routing protocol for heterogeneous ...

    Indian Academy of Sciences (India)

    NONITA SHARMA

    Event detection; wireless sensor networks; hybrid routing; cost benefit analysis; proactive routing; reactive routing. 1. ... additional energy, high processing power, etc. are deployed to extend the .... transmit to its parent node. (2) Reactive ...

  7. Real-Time QoS Routing Protocols in Wireless Multimedia Sensor Networks: Study and Analysis.

    Science.gov (United States)

    Alanazi, Adwan; Elleithy, Khaled

    2015-09-02

    Many routing protocols have been proposed for wireless sensor networks. These routing protocols are almost always based on energy efficiency. However, recent advances in complementary metal-oxide semiconductor (CMOS) cameras and small microphones have led to the development of Wireless Multimedia Sensor Networks (WMSN) as a class of wireless sensor networks which pose additional challenges. The transmission of imaging and video data needs routing protocols with both energy efficiency and Quality of Service (QoS) characteristics in order to guarantee the efficient use of the sensor nodes and effective access to the collected data. Also, with integration of real time applications in Wireless Senor Networks (WSNs), the use of QoS routing protocols is not only becoming a significant topic, but is also gaining the attention of researchers. In designing an efficient QoS routing protocol, the reliability and guarantee of end-to-end delay are critical events while conserving energy. Thus, considerable research has been focused on designing energy efficient and robust QoS routing protocols. In this paper, we present a state of the art research work based on real-time QoS routing protocols for WMSNs that have already been proposed. This paper categorizes the real-time QoS routing protocols into probabilistic and deterministic protocols. In addition, both categories are classified into soft and hard real time protocols by highlighting the QoS issues including the limitations and features of each protocol. Furthermore, we have compared the performance of mobility-aware query based real-time QoS routing protocols from each category using Network Simulator-2 (NS2). This paper also focuses on the design challenges and future research directions as well as highlights the characteristics of each QoS routing protocol.

  8. A Family of ACO Routing Protocols for Mobile Ad Hoc Networks

    Science.gov (United States)

    Rupérez Cañas, Delfín; Sandoval Orozco, Ana Lucila; García Villalba, Luis Javier; Kim, Tai-hoon

    2017-01-01

    In this work, an ACO routing protocol for mobile ad hoc networks based on AntHocNet is specified. As its predecessor, this new protocol, called AntOR, is hybrid in the sense that it contains elements from both reactive and proactive routing. Specifically, it combines a reactive route setup process with a proactive route maintenance and improvement process. Key aspects of the AntOR protocol are the disjoint-link and disjoint-node routes, separation between the regular pheromone and the virtual pheromone in the diffusion process and the exploration of routes, taking into consideration the number of hops in the best routes. In this work, a family of ACO routing protocols based on AntOR is also specified. These protocols are based on protocol successive refinements. In this work, we also present a parallelized version of AntOR that we call PAntOR. Using programming multiprocessor architectures based on the shared memory protocol, PAntOR allows running tasks in parallel using threads. This parallelization is applicable in the route setup phase, route local repair process and link failure notification. In addition, a variant of PAntOR that consists of having more than one interface, which we call PAntOR-MI (PAntOR-Multiple Interface), is specified. This approach parallelizes the sending of broadcast messages by interface through threads. PMID:28531159

  9. A Family of ACO Routing Protocols for Mobile Ad Hoc Networks.

    Science.gov (United States)

    Rupérez Cañas, Delfín; Sandoval Orozco, Ana Lucila; García Villalba, Luis Javier; Kim, Tai-Hoon

    2017-05-22

    In this work, an ACO routing protocol for mobile ad hoc networks based on AntHocNet is specified. As its predecessor, this new protocol, called AntOR, is hybrid in the sense that it contains elements from both reactive and proactive routing. Specifically, it combines a reactive route setup process with a proactive route maintenance and improvement process. Key aspects of the AntOR protocol are the disjoint-link and disjoint-node routes, separation between the regular pheromone and the virtual pheromone in the diffusion process and the exploration of routes, taking into consideration the number of hops in the best routes. In this work, a family of ACO routing protocols based on AntOR is also specified. These protocols are based on protocol successive refinements. In this work, we also present a parallelized version of AntOR that we call PAntOR. Using programming multiprocessor architectures based on the shared memory protocol, PAntOR allows running tasks in parallel using threads. This parallelization is applicable in the route setup phase, route local repair process and link failure notification. In addition, a variant of PAntOR that consists of having more than one interface, which we call PAntOR-MI (PAntOR-Multiple Interface), is specified. This approach parallelizes the sending of broadcast messages by interface through threads.

  10. IMPLEMENTASI IP V 6 MULTICAST DALAM JARINGAN WIRELESS

    Directory of Open Access Journals (Sweden)

    Dessyanto Boedi Prasetyo

    2015-04-01

    Full Text Available Teleconferencing is a media technology to create a long-distance communication of audio data and video can also be data. With teleconferencing you can perform a communication with another person that much with a relatively low cost. At this time the use of computers in a network more complex. Some time ago has developed a new network protocol, the IPv6 is a solution to overcome the deficiencies found on previous generation protocol is IPv4 Multicast is a communication mechanism of one-to-many, or point-to-multipoint. In IPv6 technology, multicast is a basic feature and has become the standard specification of every router. In the implementation is done using IPv6 multicast teleconferencing application on the LAN network topology. At the teleconference has been observed with the amount of traffic parameters that occurred during the last teleconference. Used in this study SDR and RAT teleconferencing applications. SDR (Session Directory Tool and RAT (Robust Audio Tool used for teleconferencing, which is part of the MBone tools. Protocol MLD (Multicast Listener Directory is also used in this study for multicast signaling can run well.

  11. A Multipath Routing Protocol Based on Bloom Filter for Multihop Wireless Networks

    Directory of Open Access Journals (Sweden)

    Junwei Jin

    2016-01-01

    Full Text Available On-demand multipath routing in a wireless ad hoc network is effective in achieving load balancing over the network and in improving the degree of resilience to mobility. In this paper, the salvage capable opportunistic node-disjoint multipath routing (SNMR protocol is proposed, which forms multiple routes for data transmission and supports packet salvaging with minimum overhead. The proposed mechanism constructs a primary path and a node-disjoint backup path together with alternative paths for the intermediate nodes in the primary path. It can be achieved by considering the reverse route back to the source stored in the route cache and the primary path information compressed by a Bloom filter. Our protocol presents higher capability in packet salvaging and lower overhead in forming multiple routes. Simulation results show that SNMR outperforms the compared protocols in terms of packet delivery ratio, normalized routing load, and throughput.

  12. Energy efficient routing protocols for wireless sensor networks: comparison and future directions

    Directory of Open Access Journals (Sweden)

    Loganathan Murukesan

    2017-01-01

    Full Text Available Wireless sensor network consists of nodes with limited resources. Hence, it is important to design protocols or algorithms which increases energy efficiency in order to improve the network lifetime. In this paper, techniques used in the network layer (routing of the internet protocol stack to achieve energy efficiency are reviewed. Usually, the routing protocols are classified into four main schemes: (1 Network Structure, (2 Communication Model, (3 Topology Based, and (4 Reliable Routing. In this work, only network structure based routing protocols are reviewed due to the page constraint. Besides, this type of protocols are much popular among the researchers since they are fairly simple to implement and produce good results as presented in this paper. Also, the pros and cons of each protocols are presented. Finally, the paper concludes with possible further research directions.

  13. Routing protocols for wireless sensor networks: What the literature says?

    Directory of Open Access Journals (Sweden)

    Amit Sarkar

    2016-12-01

    Full Text Available Routing in Wireless Sensor Networks (WSNs plays a significant role in the field of environment-oriented monitoring, traffic monitoring, etc. Here, wide contributions that are made toward routing in WSN are explored. The paper mainly aims to categorize the routing problems and examines the routing-related optimization problems. For achieving the motive, 50 papers from the standard journals are collected and primarily reviewed in a chronological way. Later, various features that are related to energy, security, speed and reliability problems of routing are discussed. Subsequently, the literature is analyzed based on the simulation environment and experimental setup, awareness over the Quality of Service (QoS and the deployment against various applications. In addition, the optimization of the routing algorithms and the meta-heuristic study of routing optimization are explored. Routing is a vast area with numerous unsolved issues and hence, various research gaps along with future directions are also presented.

  14. A Performance Study of LEACH and Direct Diffusion Routing Protocols in Wireless Sensor Network

    International Nuclear Information System (INIS)

    Fakher, S.; Sharshar, K.; Moawad, M.I.; Shokair, M.

    2016-01-01

    The Wireless Sensor Network (WSN) is composed of a large number of sensor nodes with limited computation communication, and battery facilities. One of the common applications of this network is environment monitoring through sensing motion, measuring temperature, humidity and radiation. One of the basic activities in WSN is data gathering which represents a great challenge. Many routing protocols are proposed for that network to collect and aggregate the data. The most popular ones are hierarchy and data centric routing protocols. The main goal of this study is to identify the most preferable routing protocol, to be used in each mobility model. This paper studies the performance of LEACH (Low Energy Adaptive Clustering Hierarchy) from hierarchy routing protocol and direct diffusion from data centric routing protocol which is not clarified until now. Moreover, a comparison between LEACH and direct diffusion protocol using NS2 simulator will be made, and an analysis of these protocols will be conducted. The comparison includes packet delivery ratio, throughput, average energy ratio, average delay, network lifetime, and routing overhead. The performance is evaluated by varying the number of sensor nodes under three mobility models Reference Point Group Mobility Model (RPGM), Manhattan and random waypoint mobility model. Simulation results show that LEACH routing protocol has a good performance in RPGM and Manhattan than random waypoint mobility model. Direct diffusion has a good performance in random waypoint mobility model than in RPGM and Manhattan mobility model

  15. Performance Analysis of On-Demand Routing Protocols in Wireless Mesh Networks

    Directory of Open Access Journals (Sweden)

    Arafatur RAHMAN

    2009-01-01

    Full Text Available Wireless Mesh Networks (WMNs have recently gained a lot of popularity due to their rapid deployment and instant communication capabilities. WMNs are dynamically self-organizing, self-configuring and self-healing with the nodes in the network automatically establishing an adiej hoc network and preserving the mesh connectivity. Designing a routing protocol for WMNs requires several aspects to consider, such as wireless networks, fixed applications, mobile applications, scalability, better performance metrics, efficient routing within infrastructure, load balancing, throughput enhancement, interference, robustness etc. To support communication, various routing protocols are designed for various networks (e.g. ad hoc, sensor, wired etc.. However, all these protocols are not suitable for WMNs, because of the architectural differences among the networks. In this paper, a detailed simulation based performance study and analysis is performed on the reactive routing protocols to verify the suitability of these protocols over such kind of networks. Ad Hoc On-Demand Distance Vector (AODV, Dynamic Source Routing (DSR and Dynamic MANET On-demand (DYMO routing protocol are considered as the representative of reactive routing protocols. The performance differentials are investigated using varying traffic load and number of source. Based on the simulation results, how the performance of each protocol can be improved is also recommended.

  16. Ad hoc mobile wireless networks principles, protocols, and applications

    CERN Document Server

    Sarkar, Subir Kumar

    2013-01-01

    The military, the research community, emergency services, and industrial environments all rely on ad hoc mobile wireless networks because of their simple infrastructure and minimal central administration. Now in its second edition, Ad Hoc Mobile Wireless Networks: Principles, Protocols, and Applications explains the concepts, mechanism, design, and performance of these highly valued systems. Following an overview of wireless network fundamentals, the book explores MAC layer, routing, multicast, and transport layer protocols for ad hoc mobile wireless networks. Next, it examines quality of serv

  17. A MODIFIED ROUTE DISCOVERY APPROACH FOR DYNAMIC SOURCE ROUTING (DSR PROTOCOL IN MOBILE AD-HOC NETWORKS

    Directory of Open Access Journals (Sweden)

    Alaa Azmi Allahham

    2017-02-01

    Full Text Available Mobile Ad-hoc networks (MANETs involved in many applications, whether commercial or military because of their characteristics that do not depend on the infrastructure as well as the freedom movement of their elements, but in return has caused this random mobility of the nodes many of the challenges, where the routing is considered one of these challenges. There are many types of routing protocols that operate within MANET networks, which responsible for finding paths between the source and destination nodes with the modernization of these paths which are constantly changing due to the dynamic topology of the network stemming from the constant random movement of the nodes. The DSR (Dynamic Source Routing routing protocol algorithm is one of these routing protocols which consist of two main stages; route discovery and maintenance, where the route discovery algorithm operates based on blind flooding of request messages. blind flooding is considered as the most well known broadcasting mechanism, it is inefficient in terms of communication and resource utilization, which causing increasing the probability of collisions, repeating send several copies of the same message, as well as increasing the delay. Hence, a new mechanism in route discovery stage and in caching the routes in DSR algorithm according to the node's location in the network and the direction of the broadcast is proposed for better performance especially in terms of delay as well as redundant packets rate. The implementation of proposed algorithms showed positive results in terms of delay, overhead, and improve the performance of MANETs in general.

  18. A Survey on Temperature-Aware Routing Protocols in Wireless Body Sensor Networks

    Directory of Open Access Journals (Sweden)

    Sangman Moh

    2013-08-01

    Full Text Available The rapid growth of the elderly population in the world and the rising cost of healthcare impose big issues for healthcare and medical monitoring. A Wireless Body Sensor Network (WBSN is comprised of small sensor nodes attached inside, on or around a human body, the main purpose of which is to monitor the functions and surroundings of the human body. However, the heat generated by the node’s circuitry and antenna could cause damage to the human tissue. Therefore, in designing a routing protocol for WBSNs, it is important to reduce the heat by incorporating temperature into the routing metric. The main contribution of this paper is to survey existing temperature-aware routing protocols that have been proposed for WBSNs. In this paper, we present a brief overview of WBSNs, review the existing routing protocols comparatively and discuss challenging open issues in the design of routing protocols.

  19. A Novel Smart Routing Protocol for Remote Health Monitoring in Medical Wireless Networks

    Directory of Open Access Journals (Sweden)

    T. V. P. Sundararajan

    2014-01-01

    Full Text Available In a Medical Wireless Network (MWN, sensors constantly monitor patient's physiological condition and movement. Inter-MWN communications are set up between the Patient Server and one or more Centralized Coordinators. However, MWNs require protocols with little energy consumption and the self-organizing attribute perceived in ad-hoc networks. The proposed Smart Routing Protocol (SRP selects only the nodes with a higher residual energy and lower traffic density for routing. This approach enhances cooperation among the nodes of a Mobile Ad Hoc Network. Consequently, SRP produces better results than the existing protocols, namely Conditional Min-Max Battery Cost Routing, Min-Max Battery Cost Routing and AdHoc On-demand Distance Vector in terms of network parameters. The performance of the erstwhile schemes for routing protocols is evaluated using the network simulator Qualnet v 4.5.

  20. Intelligent QoS routing algorithm based on improved AODV protocol for Ad Hoc networks

    Science.gov (United States)

    Huibin, Liu; Jun, Zhang

    2016-04-01

    Mobile Ad Hoc Networks were playing an increasingly important part in disaster reliefs, military battlefields and scientific explorations. However, networks routing difficulties are more and more outstanding due to inherent structures. This paper proposed an improved cuckoo searching-based Ad hoc On-Demand Distance Vector Routing protocol (CSAODV). It elaborately designs the calculation methods of optimal routing algorithm used by protocol and transmission mechanism of communication-package. In calculation of optimal routing algorithm by CS Algorithm, by increasing QoS constraint, the found optimal routing algorithm can conform to the requirements of specified bandwidth and time delay, and a certain balance can be obtained among computation spending, bandwidth and time delay. Take advantage of NS2 simulation software to take performance test on protocol in three circumstances and validate the feasibility and validity of CSAODV protocol. In results, CSAODV routing protocol is more adapt to the change of network topological structure than AODV protocol, which improves package delivery fraction of protocol effectively, reduce the transmission time delay of network, reduce the extra burden to network brought by controlling information, and improve the routing efficiency of network.

  1. A Comparative Study of Wireless Sensor Networks and Their Routing Protocols

    Directory of Open Access Journals (Sweden)

    Subhajit Pal

    2010-11-01

    Full Text Available Recent developments in the area of micro-sensor devices have accelerated advances in the sensor networks field leading to many new protocols specifically designed for wireless sensor networks (WSNs. Wireless sensor networks with hundreds to thousands of sensor nodes can gather information from an unattended location and transmit the gathered data to a particular user, depending on the application. These sensor nodes have some constraints due to their limited energy, storage capacity and computing power. Data are routed from one node to other using different routing protocols. There are a number of routing protocols for wireless sensor networks. In this review article, we discuss the architecture of wireless sensor networks. Further, we categorize the routing protocols according to some key factors and summarize their mode of operation. Finally, we provide a comparative study on these various protocols.

  2. Model-Checking Driven Design of QoS-Based Routing Protocol for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Zhi Chen

    2015-01-01

    Full Text Available Accurate and reliable routing protocols with Quality of Service (QoS support determine the mission-critical application efficiency in WSNs. This paper proposes a model-checking design driven framework for designing the QoS-based routing protocols of WSNs, which involves the light-weight design process, the timed automata model, and the alternative QoS verification properties. The accurate feedback of continually model checking in the iterative design process effectively stimulates the parameter tuning of the protocols. We demonstrate the straightforward and modular characteristics of the proposed framework in designing a prototype QoS-based routing protocol. The prototype study shows that the model-checking design framework may complement other design methods and ensure the QoS implementation of the QoS-based routing protocol design for WSNs.

  3. A Comprehensive Survey on Hierarchical-Based Routing Protocols for Mobile Wireless Sensor Networks: Review, Taxonomy, and Future Directions

    Directory of Open Access Journals (Sweden)

    Nabil Sabor

    2017-01-01

    Full Text Available Introducing mobility to Wireless Sensor Networks (WSNs puts new challenges particularly in designing of routing protocols. Mobility can be applied to the sensor nodes and/or the sink node in the network. Many routing protocols have been developed to support the mobility of WSNs. These protocols are divided depending on the routing structure into hierarchical-based, flat-based, and location-based routing protocols. However, the hierarchical-based routing protocols outperform the other routing types in saving energy, scalability, and extending lifetime of Mobile WSNs (MWSNs. Selecting an appropriate hierarchical routing protocol for specific applications is an important and difficult task. Therefore, this paper focuses on reviewing some of the recently hierarchical-based routing protocols that are developed in the last five years for MWSNs. This survey divides the hierarchical-based routing protocols into two broad groups, namely, classical-based and optimized-based routing protocols. Also, we present a detailed classification of the reviewed protocols according to the routing approach, control manner, mobile element, mobility pattern, network architecture, clustering attributes, protocol operation, path establishment, communication paradigm, energy model, protocol objectives, and applications. Moreover, a comparison between the reviewed protocols is investigated in this survey depending on delay, network size, energy-efficiency, and scalability while mentioning the advantages and drawbacks of each protocol. Finally, we summarize and conclude the paper with future directions.

  4. The Application of RPL Routing Protocol in Low Power Wireless Sensor and Lossy Networks

    Directory of Open Access Journals (Sweden)

    Xun Yang

    2014-05-01

    Full Text Available With the continuous development of computer information technology, wireless sensor has been successfully changed the mode of human life, at the same time, as one of the technologies continues to improve the future life, how to better integration with the RPL routing protocols together become one of research focuses in the current climate. This paper start from the wireless sensor network, briefly discusses the concept, followed by systematic exposition of RPL routing protocol developed background, relevant standards, working principle, topology and related terms, and finally explore the RPL routing protocol in wireless sensor low power lossy network applications.

  5. EpSoc: Social-Based Epidemic-Based Routing Protocol in Opportunistic Mobile Social Network

    Directory of Open Access Journals (Sweden)

    Halikul Lenando

    2018-01-01

    Full Text Available In opportunistic networks, the nature of intermittent and disruptive connections degrades the efficiency of routing. Epidemic routing protocol is used as a benchmark for most of routing protocols in opportunistic mobile social networks (OMSNs due to its high message delivery and latency. However, Epidemic incurs high cost in terms of overhead and hop count. In this paper, we propose a hybrid routing protocol called EpSoc which utilizes the Epidemic routing forwarding strategy and exploits an important social feature, that is, degree centrality. Two techniques are used in EpSoc. Messages’ TTL is adjusted based on the degree centrality of nodes, and the message blocking mechanism is used to control replication. Simulation results show that EpSoc increases the delivery ratio and decreases the overhead ratio, the average latency, and the hop counts as compared to Epidemic and Bubble Rap.

  6. A Secure Routing Protocol for Wireless Sensor Networks Considering Secure Data Aggregation

    Directory of Open Access Journals (Sweden)

    Triana Mugia Rahayu

    2015-06-01

    Full Text Available The commonly unattended and hostile deployments of WSNs and their resource-constrained sensor devices have led to an increasing demand for secure energy-efficient protocols. Routing and data aggregation receive the most attention since they are among the daily network routines. With the awareness of such demand, we found that so far there has been no work that lays out a secure routing protocol as the foundation for a secure data aggregation protocol. We argue that the secure routing role would be rendered useless if the data aggregation scheme built on it is not secure. Conversely, the secure data aggregation protocol needs a secure underlying routing protocol as its foundation in order to be effectively optimal. As an attempt for the solution, we devise an energy-aware protocol based on LEACH and ESPDA that combines secure routing protocol and secure data aggregation protocol. We then evaluate its security effectiveness and its energy-efficiency aspects, knowing that there are always trade-off between both.

  7. ABORt: Acknowledgement-Based Opportunistic Routing Protocol for High Data Rate Multichannel WSNs

    Directory of Open Access Journals (Sweden)

    Hamadoun Tall

    2017-10-01

    Full Text Available The ease of deployment and the auto-configuration capabilities of Wireless Sensor Networks (WSNs make them very attractive in different domains like environmental, home automation or heath care applications. The use of multichannel communications in WSNs helps to improve the overall performance of the network. However, in heavy traffic scenarios, routing protocols should be adapted to allow load balancing and to avoid losing data packets due to congestion and queue overflow. In this paper, we present an Acknowledgement-Based Opportunistic Routing (ABORt protocol designed for high data rate multichannel WSNs. It is a low overhead protocol that does not rely on synchronization for control traffic exchange during the operational phase of the network. ABORt is an opportunistic protocol that relies on link layer acknowledgements to disseminate routing metrics, which helps to reduce overhead. The performance of ABORt is evaluated using the Cooja simulator and the obtained results show that ABORt has a high packet delivery ratio with reduced packet end-to-end delay compared to two single channel routing protocols and two multichannel routing protocols that use number of hops and expected transmission count as routing metrics.

  8. Performance Evaluation of AODV Routing Protocol in VANET with NS2

    Directory of Open Access Journals (Sweden)

    Divya Rathi

    2017-03-01

    Full Text Available In intelligent transportation systems, the collaboration between vehicles and the road side units is essential to bring these systems to realization. The emerging Vehicular Ad Hoc Network (VANET is becoming more and more important as it provides intelligent transportation application, comfort, safety, entertainment for people in vehicles. In order to provide stable routes and to get good performance in VANET, there is a need of proper routing protocols must be designed. In this paper, we are working with the very well-known ad-hoc on-demand distance vector (AODV routing protocol. The existing Routing protocol AODV-L which is based on the Link expiration time is extended to propose a more reliable AODV-AD which is based on multichannel MAC protocol. For the performance evaluation of routing protocols, a simulation tool ‘NS2’ has been used. Simulation results show that the proposed AODV-AD protocol can achieves better performances in forms of high Route stability, Packet Delivery ratio and packet loss rate than traditional AODV-L and traditional AODV.

  9. Energy neutral protocol based on hierarchical routing techniques for energy harvesting wireless sensor network

    Science.gov (United States)

    Muhammad, Umar B.; Ezugwu, Absalom E.; Ofem, Paulinus O.; Rajamäki, Jyri; Aderemi, Adewumi O.

    2017-06-01

    Recently, researchers in the field of wireless sensor networks have resorted to energy harvesting techniques that allows energy to be harvested from the ambient environment to power sensor nodes. Using such Energy harvesting techniques together with proper routing protocols, an Energy Neutral state can be achieved so that sensor nodes can run perpetually. In this paper, we propose an Energy Neutral LEACH routing protocol which is an extension to the traditional LEACH protocol. The goal of the proposed protocol is to use Gateway node in each cluster so as to reduce the data transmission ranges of cluster head nodes. Simulation results show that the proposed routing protocol achieves a higher throughput and ensure the energy neutral status of the entire network.

  10. Advanced flooding-based routing protocols for underwater sensor networks

    OpenAIRE

    Isufi, E.; Dol, H.; Leus, G.J.T.

    2016-01-01

    Flooding-based protocols are a reliable solution to deliver packets in underwater sensor networks. However, these protocols potentially involve all the nodes in the forwarding process. Thus, the performance and energy efficiency are not optimal. In this work, we propose some advances of a flooding-based protocol with the goal to improve the performance and the energy efficiency. The first idea considers the node position information in order to reduce the number of relays that may apply flood...

  11. Network Coding to Enhance Standard Routing Protocols in Wireless Mesh Networks

    DEFF Research Database (Denmark)

    Pahlevani, Peyman; Roetter, Daniel Enrique Lucani; Fitzek, Frank

    2013-01-01

    This paper introduces a design and simulation of a locally optimized network coding protocol, called PlayNCool, for wireless mesh networks. PlayN-Cool is easy to implement and compatible with existing routing protocols and devices. This allows the system to gain from network coding capabilities i...

  12. A Smart Collaborative Routing Protocol for Reliable Data Diffusion in IoT Scenarios.

    Science.gov (United States)

    Ai, Zheng-Yang; Zhou, Yu-Tong; Song, Fei

    2018-06-13

    It is knotty for current routing protocols to meet the needs of reliable data diffusion during the Internet of Things (IoT) deployments. Due to the random placement, limited resources and unattended features of existing sensor nodes, the wireless transmissions are easily exposed to unauthorized users, which becomes a vulnerable area for various malicious attacks, such as wormhole and Sybil attacks. However, the scheme based on geographic location is a suitable candidate to defend against them. This paper is inspired to propose a smart collaborative routing protocol, Geographic energy aware routing and Inspecting Node (GIN), for guaranteeing the reliability of data exchanging. The proposed protocol integrates the directed diffusion routing, Greedy Perimeter Stateless Routing (GPSR), and the inspecting node mechanism. We first discuss current wireless routing protocols from three diverse perspectives (improving transmission rate, shortening transmission range and reducing transmission consumption). Then, the details of GIN, including the model establishment and implementation processes, are presented by means of the theoretical analysis. Through leveraging the game theory, the inspecting node is elected to monitor the network behaviors. Thirdly, we evaluate the network performances, in terms of transmission delay, packet loss ratio, and throughput, between GIN and three traditional schemes (i.e., Flooding, GPSR, and GEAR). The simulation results illustrate that the proposed protocol is able to outperform the others.

  13. A Multicast Sparse-Grooming Algorithm Based on Network Coding in WDM Networks

    Science.gov (United States)

    Zhang, Shengfeng; Peng, Han; Sui, Meng; Liu, Huanlin

    2015-03-01

    To improve the limited number of wavelength utilization and decrease the traffic blocking probability in sparse-grooming wavelength-division multiplexing (WDM) networks, a multicast sparse-grooming algorithm based on network coding (MCSA-NC) is put forward to solve the routing problem for dynamic multicast requests in this paper. In the proposed algorithm, a traffic partition strategy, that the coarse-granularity multicast request with grooming capability on the source node is split into several fine-granularity multicast requests, is designed so as to increase the probability for traffic grooming successfully in MCSA-NC. Besides considering that multiple destinations should receive the data from source of the multicast request at the same time, the traditional transmission mechanism is improved by constructing edge-disjoint paths for each split multicast request. Moreover, in order to reduce the number of wavelengths required and further decrease the traffic blocking probability, a light-tree reconfiguration mechanism is presented in the MCSA-NC, which can select a minimal cost light tree from the established edge-disjoint paths for a new multicast request.

  14. Suppressing traffic-driven epidemic spreading by use of the efficient routing protocol

    International Nuclear Information System (INIS)

    Yang, Han-Xin; Wu, Zhi-Xi

    2014-01-01

    Despite extensive work on the interplay between traffic dynamics and epidemic spreading, the control of epidemic spreading by routing strategies has not received adequate attention. In this paper, we study the impact of an efficient routing protocol on epidemic spreading. In the case of infinite node-delivery capacity, where the traffic is free of congestion, we find that that there exist optimal values of routing parameter, leading to the maximal epidemic threshold. This means that epidemic spreading can be effectively controlled by fine tuning the routing scheme. Moreover, we find that an increase in the average network connectivity and the emergence of traffic congestion can suppress the epidemic outbreak. (paper)

  15. Multipath Activity Based Routing Protocol for Mobile ‎Cognitive Radio Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    Shereen Omar

    2017-01-01

    Full Text Available Cognitive radio networks improve spectrum utilization by ‎sharing licensed spectrum with cognitive radio devices. In ‎cognitive radio ad hoc networks the routing protocol is one ‎of the most challenging tasks due to the changes in ‎frequency spectrum and the interrupted connectivity ‎caused by the primary user activity. In this paper, a multi‎path activity based routing protocol for cognitive radio ‎network (MACNRP is proposed. The protocol utilizes ‎channel availability and creates multiple node-disjoint ‎routes between the source and destination nodes. The ‎proposed protocol is compared with D2CARP and FTCRP ‎protocols. The performance evaluation is conducted ‎through mathematical analysis and using OPNET ‎simulation. The performance of the proposed protocol ‎achieves an increase in network throughput; besides it ‎decreases the probability of route failure due to node ‎mobility and primary user activity. We have found that the ‎MACNRP scheme results in 50% to 75% reduction in ‎blocking probability and 33% to 78% improvement in ‎network throughput, with a reasonable additional routing ‎overhead and average packet delay. Due to the successful ‎reduction of collision between primary users and ‎cognitive users, the MACNRP scheme results in decreasing ‎the path failure rate by 50% to 87%.‎

  16. Achieving sink node anonymity in tactical wireless sensor networks using a reactive routing protocol

    Science.gov (United States)

    2017-06-01

    node anonymity, base station anonymity, Wireless Sensor Networks (WSN), Mobile Ad hoc Network (MANET), Lightweight Ad hoc On-Demand – Next Generation ... Generation (LOADng) reactive-routing protocol to achieve anonymity. This modified protocol prevents an attacker from identifying the sink node without...within the constraints of WSN communication protocols, specifically IEEE 802.15.4. We use and modify the Lightweight Ad hoc On-Demand – Next Generation

  17. Efficient Security Mechanisms for the Border Gateway Routing Protocol

    Science.gov (United States)

    1997-08-22

    Finding Algorithm for Loop- Free Routing. IEEE/ACM Transactions on Networking, 5(1):148{160, Feb. 1997. [7] International Standards Organization. ISO/IEC...Jersey 07974, Feb. 1985. ftp://netlib.att.com/netlib/att/cs/ cstr /117.ps.Z. [16] S. L. Murphy. Presentation in Panel on \\Security Architecture for the

  18. Energy- Efficient Routing Protocols For Wireless Sensor Network A Review

    Directory of Open Access Journals (Sweden)

    Pardeep Kaur

    2017-12-01

    Full Text Available There has been plenty of interest in building and deploying sensor networks. Wireless sensor network is a collection of a large number of small nodes which acts as routers also. These nodes carry very limited power source which is non-rechargeable and non-replaceable which makes energy consumption an significant issue. Energy conservation is a very important issue for prolonging the lifetime of the network. As the sensor nodes act like routers as well the determination of routing technique plays a key role in controlling the consumption of energy. This paper describes the framework of wireless sensor network and the analysis and study of various research work related to Energy Efficient Routing in Wireless Sensor Networks.

  19. Secure energy efficient routing protocol for wireless sensor network

    OpenAIRE

    Das Ayan Kumar; Chaki Rituparna; Dey Kashi Nath

    2016-01-01

    The ease of deployment of economic sensor networks has always been a boon to disaster management applications. However, their vulnerability to a number of security threats makes communication a challenging task. This paper proposes a new routing technique to prevent from both external threats and internal threats like hello flooding, eavesdropping and wormhole attack. In this approach one way hash chain is used to reduce the energy drainage. Level based event driven clustering also helps to s...

  20. A Study on IP Network Recovery through Routing Protocols

    Directory of Open Access Journals (Sweden)

    K. Karthik

    2016-09-01

    Full Text Available Internet has taken major role in our communication infrastructure. Such that requirement of internet availability and reliability has increasing accordingly. The major network failure reasons are failure of node and failure of link among the nodes. This can reduce the performance of major applications in an IP networks. The network recovery should be fast enough so that service interruption of link or node failure. The new path taken by the diverted traffic can be computed either at the time of failures or before failures. These mechanisms are known as Reactive and Proactive protocols respectively. In this paper, we surveyed reactive and proactive protocols mechanisms for IP network recovery.

  1. WDM Multicast Tree Construction Algorithms and Their Comparative Evaluations

    Science.gov (United States)

    Makabe, Tsutomu; Mikoshi, Taiju; Takenaka, Toyofumi

    We propose novel tree construction algorithms for multicast communication in photonic networks. Since multicast communications consume many more link resources than unicast communications, effective algorithms for route selection and wavelength assignment are required. We propose a novel tree construction algorithm, called the Weighted Steiner Tree (WST) algorithm and a variation of the WST algorithm, called the Composite Weighted Steiner Tree (CWST) algorithm. Because these algorithms are based on the Steiner Tree algorithm, link resources among source and destination pairs tend to be commonly used and link utilization ratios are improved. Because of this, these algorithms can accept many more multicast requests than other multicast tree construction algorithms based on the Dijkstra algorithm. However, under certain delay constraints, the blocking characteristics of the proposed Weighted Steiner Tree algorithm deteriorate since some light paths between source and destinations use many hops and cannot satisfy the delay constraint. In order to adapt the approach to the delay-sensitive environments, we have devised the Composite Weighted Steiner Tree algorithm comprising the Weighted Steiner Tree algorithm and the Dijkstra algorithm for use in a delay constrained environment such as an IPTV application. In this paper, we also give the results of simulation experiments which demonstrate the superiority of the proposed Composite Weighted Steiner Tree algorithm compared with the Distributed Minimum Hop Tree (DMHT) algorithm, from the viewpoint of the light-tree request blocking.

  2. SOME NOTES ON COST ALLOCATION IN MULTICASTING

    Directory of Open Access Journals (Sweden)

    Darko Skorin-Kapov

    2012-12-01

    Full Text Available We analyze the cost allocation strategies with the problef of broadcasting information from some source to a number of communication network users. A multicast routing chooses a minimum cost tree network that spans the source and all the receivers. The cost of such a network is distributed among its receivers who may be individuals or organizations with possibly conflicting interests. Providing network developers, users and owners with practical computable 'fair' cost allocation solution procedures is of great importance for network mamagement. Consequently, this multidisciplinary problem was extensively studied by Operational Researchers, Economists, Mathematicians and Computer Scientists. The fairness of various proposed solutions was even argued in US courts. This presentation overviews some previously published, as well as some recent results, in the development of algorithmic mechanisms to efficiently compute 'attractive' cost allocation solutions for multicast networks. Specifically, we will analyze cooperative game theory based cost allocation models that avoid cross subsidies and/or are distance and population monotonic. We will also present some related open cost allocation problems and the potential contribution that such models might make to this problem in the future.

  3. An Environment-Friendly Multipath Routing Protocol for Underwater Acoustic Sensor Network

    Directory of Open Access Journals (Sweden)

    Yun Li

    2017-01-01

    Full Text Available Underwater Acoustic Sensor Network (UASN is a promising technique by facilitating a wide range of aquatic applications. However, routing scheme in UASN is a challenging task because of the characteristics of the nodes mobility, interruption of link, and interference caused by other underwater acoustic systems such as marine mammals. In order to achieve reliable data delivery in UASN, in this work, we present a disjoint multipath disruption-tolerant routing protocol for UASN (ENMR, which incorporates the Hue, Saturation, and Value color space (HSV model to establish routing paths to greedily forward data packets to sink nodes. ENMR applies the mechanism to maintain the network topology. Simulation results show that, compared with the classic underwater routing protocols named PVBF, ENMR can improve packet delivery ratio and reduce network latency while avoiding introducing additional energy consumption.

  4. Evaluation and development the routing protocol of a fully functional simulation environment for VANETs

    Science.gov (United States)

    Ali, Azhar Tareq; Warip, Mohd Nazri Mohd; Yaakob, Naimah; Abduljabbar, Waleed Khalid; Atta, Abdu Mohammed Ali

    2017-11-01

    Vehicular Ad-hoc Networks (VANETs) is an area of wireless technologies that is attracting a great deal of interest. There are still several areas of VANETS, such as security and routing protocols, medium access control, that lack large amounts of research. There is also a lack of freely available simulators that can quickly and accurately simulate VANETs. The main goal of this paper is to develop a freely available VANETS simulator and to evaluate popular mobile ad-hoc network routing protocols in several VANETS scenarios. The VANETS simulator consisted of a network simulator, traffic (mobility simulator) and used a client-server application to keep the two simulators in sync. The VANETS simulator also models buildings to create a more realistic wireless network environment. Ad-Hoc Distance Vector routing (AODV), Dynamic Source Routing (DSR) and Dynamic MANET On-demand (DYMO) were initially simulated in a city, country, and highway environment to provide an overall evaluation.

  5. Secure energy efficient routing protocol for wireless sensor network

    Directory of Open Access Journals (Sweden)

    Das Ayan Kumar

    2016-03-01

    Full Text Available The ease of deployment of economic sensor networks has always been a boon to disaster management applications. However, their vulnerability to a number of security threats makes communication a challenging task. This paper proposes a new routing technique to prevent from both external threats and internal threats like hello flooding, eavesdropping and wormhole attack. In this approach one way hash chain is used to reduce the energy drainage. Level based event driven clustering also helps to save energy. The simulation results show that the proposed scheme extends network lifetime even when the cluster based wireless sensor network is under attack.

  6. Application of Game Theory Approaches in Routing Protocols for Wireless Networks

    Science.gov (United States)

    Javidi, Mohammad M.; Aliahmadipour, Laya

    2011-09-01

    An important and essential issue for wireless networks is routing protocol design that is a major technical challenge due to the function of the network. Game theory is a powerful mathematical tool that analyzes the strategic interactions among multiple decision makers and the results of researches show that applied game theory in routing protocol lead to improvement the network performance through reduce overhead and motivates selfish nodes to collaborate in the network. This paper presents a review and comparison for typical representatives of routing protocols designed that applied game theory approaches for various wireless networks such as ad hoc networks, mobile ad hoc networks and sensor networks that all of them lead to improve the network performance.

  7. Design and Analysis of Secure Routing Protocol for Wireless Sensor Networks

    Science.gov (United States)

    Wang, Jiong; Zhang, Hua

    2017-09-01

    In recent years, with the development of science and technology and the progress of the times, China's wireless network technology has become increasingly prosperous and it plays an important role in social production and life. In this context, in order to further to enhance the stability of wireless network data transmission and security enhancements, the staff need to focus on routing security and carry out related work. Based on this, this paper analyzes the design of wireless sensor based on secure routing protocol.

  8. DRUG: An Energy-Efficient Data-Centric Routing Protocol for Wireless Sensor Networks

    OpenAIRE

    Sahoo, B. P. S.; Puthal, Deepak

    2014-01-01

    In general, sensor nodes are deployed in left unattended area. In such situation feeding energy to the batteries or replacing the batteries is difficult or even sometimes impossible too. Therefore, prolonging the network lifetime is an important optimization goal in this aspect. In this paper, we propose a new Energy-efficient Datacentric RoUtinG protocol called DRUG. In this paper, we propose an adaptive Data centric approach to find an optimal routing path from source to sink when the senso...

  9. A Survey on the Taxonomy of Cluster-Based Routing Protocols for Homogeneous Wireless Sensor Networks

    Science.gov (United States)

    Naeimi, Soroush; Ghafghazi, Hamidreza; Chow, Chee-Onn; Ishii, Hiroshi

    2012-01-01

    The past few years have witnessed increased interest among researchers in cluster-based protocols for homogeneous networks because of their better scalability and higher energy efficiency than other routing protocols. Given the limited capabilities of sensor nodes in terms of energy resources, processing and communication range, the cluster-based protocols should be compatible with these constraints in either the setup state or steady data transmission state. With focus on these constraints, we classify routing protocols according to their objectives and methods towards addressing the shortcomings of clustering process on each stage of cluster head selection, cluster formation, data aggregation and data communication. We summarize the techniques and methods used in these categories, while the weakness and strength of each protocol is pointed out in details. Furthermore, taxonomy of the protocols in each phase is given to provide a deeper understanding of current clustering approaches. Ultimately based on the existing research, a summary of the issues and solutions of the attributes and characteristics of clustering approaches and some open research areas in cluster-based routing protocols that can be further pursued are provided. PMID:22969350

  10. IMHRP: Improved Multi-Hop Routing Protocol for Wireless Sensor Networks

    Science.gov (United States)

    Huang, Jianhua; Ruan, Danwei; Hong, Yadong; Zhao, Ziming; Zheng, Hong

    2017-10-01

    Wireless sensor network (WSN) is a self-organizing system formed by a large number of low-cost sensor nodes through wireless communication. Sensor nodes collect environmental information and transmit it to the base station (BS). Sensor nodes usually have very limited battery energy. The batteries cannot be charged or replaced. Therefore, it is necessary to design an energy efficient routing protocol to maximize the network lifetime. This paper presents an improved multi-hop routing protocol (IMHRP) for homogeneous networks. In the IMHRP protocol, based on the distances to the BS, the CH nodes are divided into internal CH nodes and external CH nodes. The set-up phase of the protocol is based on the LEACH protocol and the minimum distance between CH nodes are limited to a special constant distance, so a more uniform distribution of CH nodes is achieved. In the steady-state phase, the routes of different CH nodes are created on the basis of the distances between the CH nodes. The energy efficiency of communication can be maximized. The simulation results show that the proposed algorithm can more effectively reduce the energy consumption of each round and prolong the network lifetime compared with LEACH protocol and MHT protocol.

  11. Cost-Effective Encryption-Based Autonomous Routing Protocol for Efficient and Secure Wireless Sensor Networks.

    Science.gov (United States)

    Saleem, Kashif; Derhab, Abdelouahid; Orgun, Mehmet A; Al-Muhtadi, Jalal; Rodrigues, Joel J P C; Khalil, Mohammed Sayim; Ali Ahmed, Adel

    2016-03-31

    The deployment of intelligent remote surveillance systems depends on wireless sensor networks (WSNs) composed of various miniature resource-constrained wireless sensor nodes. The development of routing protocols for WSNs is a major challenge because of their severe resource constraints, ad hoc topology and dynamic nature. Among those proposed routing protocols, the biology-inspired self-organized secure autonomous routing protocol (BIOSARP) involves an artificial immune system (AIS) that requires a certain amount of time to build up knowledge of neighboring nodes. The AIS algorithm uses this knowledge to distinguish between self and non-self neighboring nodes. The knowledge-building phase is a critical period in the WSN lifespan and requires active security measures. This paper proposes an enhanced BIOSARP (E-BIOSARP) that incorporates a random key encryption mechanism in a cost-effective manner to provide active security measures in WSNs. A detailed description of E-BIOSARP is presented, followed by an extensive security and performance analysis to demonstrate its efficiency. A scenario with E-BIOSARP is implemented in network simulator 2 (ns-2) and is populated with malicious nodes for analysis. Furthermore, E-BIOSARP is compared with state-of-the-art secure routing protocols in terms of processing time, delivery ratio, energy consumption, and packet overhead. The findings show that the proposed mechanism can efficiently protect WSNs from selective forwarding, brute-force or exhaustive key search, spoofing, eavesdropping, replaying or altering of routing information, cloning, acknowledgment spoofing, HELLO flood attacks, and Sybil attacks.

  12. Cost-Effective Encryption-Based Autonomous Routing Protocol for Efficient and Secure Wireless Sensor Networks

    Science.gov (United States)

    Saleem, Kashif; Derhab, Abdelouahid; Orgun, Mehmet A.; Al-Muhtadi, Jalal; Rodrigues, Joel J. P. C.; Khalil, Mohammed Sayim; Ali Ahmed, Adel

    2016-01-01

    The deployment of intelligent remote surveillance systems depends on wireless sensor networks (WSNs) composed of various miniature resource-constrained wireless sensor nodes. The development of routing protocols for WSNs is a major challenge because of their severe resource constraints, ad hoc topology and dynamic nature. Among those proposed routing protocols, the biology-inspired self-organized secure autonomous routing protocol (BIOSARP) involves an artificial immune system (AIS) that requires a certain amount of time to build up knowledge of neighboring nodes. The AIS algorithm uses this knowledge to distinguish between self and non-self neighboring nodes. The knowledge-building phase is a critical period in the WSN lifespan and requires active security measures. This paper proposes an enhanced BIOSARP (E-BIOSARP) that incorporates a random key encryption mechanism in a cost-effective manner to provide active security measures in WSNs. A detailed description of E-BIOSARP is presented, followed by an extensive security and performance analysis to demonstrate its efficiency. A scenario with E-BIOSARP is implemented in network simulator 2 (ns-2) and is populated with malicious nodes for analysis. Furthermore, E-BIOSARP is compared with state-of-the-art secure routing protocols in terms of processing time, delivery ratio, energy consumption, and packet overhead. The findings show that the proposed mechanism can efficiently protect WSNs from selective forwarding, brute-force or exhaustive key search, spoofing, eavesdropping, replaying or altering of routing information, cloning, acknowledgment spoofing, HELLO flood attacks, and Sybil attacks. PMID:27043572

  13. Receiver-Based Ad Hoc On Demand Multipath Routing Protocol for Mobile Ad Hoc Networks.

    Science.gov (United States)

    Al-Nahari, Abdulaziz; Mohamad, Mohd Murtadha

    2016-01-01

    Decreasing the route rediscovery time process in reactive routing protocols is challenging in mobile ad hoc networks. Links between nodes are continuously established and broken because of the characteristics of the network. Finding multiple routes to increase the reliability is also important but requires a fast update, especially in high traffic load and high mobility where paths can be broken as well. The sender node keeps re-establishing path discovery to find new paths, which makes for long time delay. In this paper we propose an improved multipath routing protocol, called Receiver-based ad hoc on demand multipath routing protocol (RB-AOMDV), which takes advantage of the reliability of the state of the art ad hoc on demand multipath distance vector (AOMDV) protocol with less re-established discovery time. The receiver node assumes the role of discovering paths when finding data packets that have not been received after a period of time. Simulation results show the delay and delivery ratio performances are improved compared with AOMDV.

  14. RELIABLE DYNAMIC SOURCE ROUTING PROTOCOL (RDSRP FOR ENERGY HARVESTING WIRELESS SENSOR NETWORKS

    Directory of Open Access Journals (Sweden)

    B. Narasimhan

    2015-03-01

    Full Text Available Wireless sensor networks (WSNs carry noteworthy pros over traditional communication. Though, unkind and composite environments fake great challenges in the reliability of WSN communications. It is more vital to develop a reliable unipath dynamic source routing protocol (RDSRPl for WSN to provide better quality of service (QoS in energy harvesting wireless sensor networks (EH-WSN. This paper proposes a dynamic source routing approach for attaining the most reliable route in EH-WSNs. Performance evaluation is carried out using NS-2 and throughput and packet delivery ratio are chosen as the metrics.

  15. The Comparative Study Some of Reactive and Proactive Routing Protocols in The Wireless Sensor Network

    Directory of Open Access Journals (Sweden)

    Anas Ali Hussien

    2018-02-01

    Full Text Available The wireless sensor network (WSN consists mostly of a large number of nodes in a large area where not all nodes are directly connected. The applications of comprise a wide variety of scenarios.The mobile nodes are free to move because this network has selfــstructured topology. Routing protocols are responsible for detecting and maintaining paths in the network, and it classified into reactive (OnـــDemand, proactive (Table driven, and hybrid. In this paper represents a performance study of some WSN routing protocols: the Dynamic Source Routing (DSR, Ad hoc On-Demand Distance Vector (AODV, and Destination-Sequenced Distance-Vector (DSDV. The comparison made according to important metrics like packet delivery ratio (PDR, total packets dropped, Average end-to-end delay (Avg EED, and normalized routing load under the Transmission Control Protocol (TCP and User Datagram Protocol (UDP traffic connection and with varying number of nodes, pause time; and  varying speed. In this work used (NSــ2.35 that installed on (Ubuntu 14.04 operating system to implementing the scenario. Conclude that the DSR has better performance in TCP connection; while the DSDV has better performance in UDP protocol.

  16. Prediction Schemes to Enhance the Routing Process in Geographical GPSR Ad Hoc Protocol

    Directory of Open Access Journals (Sweden)

    Raed Saqour

    2007-01-01

    Full Text Available Geographical routing protocols have received a serious attention due to more advantages they have in comparison to the conventional routing protocols. They require information about the physical position of nodes needed to be available. Commonly, each node determines its own position through the use of Global Positioning System (GPS or some other type of positioning service. Greedy Perimeter Stateless Routing (GPSR protocol, which is one of geographical routing protocols, limits the forwarding decision of the packet based on the node's own position, the destination's position and the position of the forwarding node's neighbors. Location information has some inaccuracy depending on the localization system and the environment exists in. This paper aims to study the impact of mobility metrics (beacon interval, and node speed on introducing location information error in GPSR protocol using different mobility models. The effect of these metrics is identified in GPSR as Neighbor Break Link (NBL problem. Based on simulation analysis, mobility prediction schemes are proposed to migrate the observed problem.

  17. Modelling and Initial Validation of the DYMO Routing Protocol for Mobile Ad-Hoc Networks

    DEFF Research Database (Denmark)

    Espensen, Kristian Asbjørn Leth; Kjeldsen, Mads Keblov; Kristensen, Lars Michael

    2008-01-01

    A mobile ad-hoc network (MANET) is an infrastructureless network established by a set of mobile devices using wireless communication. The Dynamic MANET On-demand (DYMO) protocol is a routing protocol for multi-hop communication in MANETs currently under development by the Internet Engineering Task...... Force (IETF). This paper presents a Coloured Petri Net (CPN) model of the mandatory parts of the DYMO protocol, and shows how scenario-based state space exploration has been used to validate key properties of the protocol. Our CPN modelling and verification work has spanned two revisions of the DYMO...... protocol specification and have had direct impact on the most recent version of the protocol specification....

  18. Scalable Multicasting over Next-Generation Internet Design, Analysis and Applications

    CERN Document Server

    Tian, Xiaohua

    2013-01-01

    Next-generation Internet providers face high expectations, as contemporary users worldwide expect high-quality multimedia functionality in a landscape of ever-expanding network applications. This volume explores the critical research issue of turning today’s greatly enhanced hardware capacity to good use in designing a scalable multicast  protocol for supporting large-scale multimedia services. Linking new hardware to improved performance in the Internet’s next incarnation is a research hot-spot in the computer communications field.   The methodical presentation deals with the key questions in turn: from the mechanics of multicast protocols to current state-of-the-art designs, and from methods of theoretical analysis of these protocols to applying them in the ns2 network simulator, known for being hard to extend. The authors’ years of research in the field inform this thorough treatment, which covers details such as applying AOM (application-oriented multicast) protocol to IPTV provision and resolving...

  19. Management of Energy Consumption on Cluster Based Routing Protocol for MANET

    Science.gov (United States)

    Hosseini-Seno, Seyed-Amin; Wan, Tat-Chee; Budiarto, Rahmat; Yamada, Masashi

    The usage of light-weight mobile devices is increasing rapidly, leading to demand for more telecommunication services. Consequently, mobile ad hoc networks and their applications have become feasible with the proliferation of light-weight mobile devices. Many protocols have been developed to handle service discovery and routing in ad hoc networks. However, the majority of them did not consider one critical aspect of this type of network, which is the limited of available energy in each node. Cluster Based Routing Protocol (CBRP) is a robust/scalable routing protocol for Mobile Ad hoc Networks (MANETs) and superior to existing protocols such as Ad hoc On-demand Distance Vector (AODV) in terms of throughput and overhead. Therefore, based on this strength, methods to increase the efficiency of energy usage are incorporated into CBRP in this work. In order to increase the stability (in term of life-time) of the network and to decrease the energy consumption of inter-cluster gateway nodes, an Enhanced Gateway Cluster Based Routing Protocol (EGCBRP) is proposed. Three methods have been introduced by EGCBRP as enhancements to the CBRP: improving the election of cluster Heads (CHs) in CBRP which is based on the maximum available energy level, implementing load balancing for inter-cluster traffic using multiple gateways, and implementing sleep state for gateway nodes to further save the energy. Furthermore, we propose an Energy Efficient Cluster Based Routing Protocol (EECBRP) which extends the EGCBRP sleep state concept into all idle member nodes, excluding the active nodes in all clusters. The experiment results show that the EGCBRP decreases the overall energy consumption of the gateway nodes up to 10% and the EECBRP reduces the energy consumption of the member nodes up to 60%, both of which in turn contribute to stabilizing the network.

  20. UMDR: Multi-Path Routing Protocol for Underwater Ad Hoc Networks with Directional Antenna

    Science.gov (United States)

    Yang, Jianmin; Liu, Songzuo; Liu, Qipei; Qiao, Gang

    2018-01-01

    This paper presents a new routing scheme for underwater ad hoc networks based on directional antennas. Ad hoc networks with directional antennas have become a hot research topic because of space reuse may increase networks capacity. At present, researchers have applied traditional self-organizing routing protocols (such as DSR, AODV) [1] [2] on this type of networks, and the routing scheme is based on the shortest path metric. However, such routing schemes often suffer from long transmission delays and frequent link fragmentation along the intermediate nodes of the selected route. This is caused by a unique feature of directional transmission, often called as “deafness”. In this paper, we take a different approach to explore the advantages of space reuse through multipath routing. This paper introduces the validity of the conventional routing scheme in underwater ad hoc networks with directional antennas, and presents a special design of multipath routing algorithm for directional transmission. The experimental results show a significant performance improvement in throughput and latency.

  1. Analysis of energy efficient routing protocols for implementation of a ubiquitous health system

    Science.gov (United States)

    Kwon, Jongwon; Park, Yongman; Koo, Sangjun; Ayurzana, Odgeral; Kim, Hiesik

    2007-12-01

    The innovative Ubiquitous-Health was born through convergence of medical service, with development of up to date information technologies and ubiquitous IT. The U-Health can be applied to a variety of special situations for managing functions of each medical center efficiently. This paper focuses on estimation of various routing protocols for implementation of U-health monitoring system. In order to facilitate wireless communication over the network, a routing protocol on the network layer is used to establish precise and efficient route between sensor nodes so that information acquired from sensors may be delivered in a timely manner. A route establishment should be considered to minimize overhead, data loss and power consumption because wireless networks for U-health are organized by a large number of sensor nodes which are small in size and have limited processing power, memory and battery life. In this paper a overview of wireless sensor network technologies commonly known is described as well as evaluation of three multi hop routing protocols which are flooding, gossiping and modified low energy adaptive clustering hierarchy(LEACH) for use with these networks using TOSSIM simulator. As a result of evaluation the integrated wireless sensor board was developed in particular. The board is embedded device based on AVR128 porting TinyOS. Also it employs bio sensor measures blood pressure, pulse frequency and ZigBee module for wireless communication. This paper accelerates the digital convergence age through continual research and development of technologies related the U-Health.

  2. SURVEY OF ENERGY COMPETENCE ROUTING PROTOCOL IN UTILIZING AODV IN MANETS (20150471)

    OpenAIRE

    TUSHAR SINGH RAJPUT; RAJ KUMAR PAUL

    2018-01-01

    In MANETs (Mobile unintentional Networks) communication at the mobile nodes will be achieved by mistreatment multihop wireless links. The aim of every protocol, in Associate in Nursing ad-hoc network, is to seek out valid routes between 2 communication nodes.

  3. Optimized energy-delay sub-network routing protocol development and implementation for wireless sensor networks

    International Nuclear Information System (INIS)

    Fonda, James W; Zawodniok, Maciej; Jagannathan, S; Watkins, Steve E

    2008-01-01

    The development and the implementation issues of a reactive optimized energy-delay sub-network routing (OEDSR) protocol for wireless sensor networks (WSN) are introduced and its performance is contrasted with the popular ad hoc on-demand distance vector (AODV) routing protocol. Analytical results illustrate the performance of the proposed OEDSR protocol, while experimental results utilizing a hardware testbed under various scenarios demonstrate improvements in energy efficiency of the OEDSR protocol. A hardware platform constructed at the University of Missouri-Rolla (UMR), now the Missouri University of Science and Technology (MST), based on the Generation 4 Smart Sensor Node (G4-SSN) prototyping platform is also described. Performance improvements are shown in terms of end-to-end (E2E) delay, throughput, route-set-up time and drop rates and energy usage is given for three topologies, including a mobile topology. Additionally, results from the hardware testbed provide valuable lessons for network deployments. Under testing OEDSR provides a factor of ten improvement in the energy used in the routing session and extends network lifetime compared to AODV. Depletion experiments show that the time until the first node failure is extended by a factor of three with the network depleting and network lifetime is extended by 6.7%

  4. An Energy Balanced and Lifetime Extended Routing Protocol for Underwater Sensor Networks.

    Science.gov (United States)

    Wang, Hao; Wang, Shilian; Zhang, Eryang; Lu, Luxi

    2018-05-17

    Energy limitation is an adverse problem in designing routing protocols for underwater sensor networks (UWSNs). To prolong the network lifetime with limited battery power, an energy balanced and efficient routing protocol, called energy balanced and lifetime extended routing protocol (EBLE), is proposed in this paper. The proposed EBLE not only balances traffic loads according to the residual energy, but also optimizes data transmissions by selecting low-cost paths. Two phases are operated in the EBLE data transmission process: (1) candidate forwarding set selection phase and (2) data transmission phase. In candidate forwarding set selection phase, nodes update candidate forwarding nodes by broadcasting the position and residual energy level information. The cost value of available nodes is calculated and stored in each sensor node. Then in data transmission phase, high residual energy and relatively low-cost paths are selected based on the cost function and residual energy level information. We also introduce detailed analysis of optimal energy consumption in UWSNs. Numerical simulation results on a variety of node distributions and data load distributions prove that EBLE outperforms other routing protocols (BTM, BEAR and direct transmission) in terms of network lifetime and energy efficiency.

  5. A Comparison of Routing Protocol for WSNs: Redundancy Based Approach A Comparison of Routing Protocol for WSNs: Redundancy Based Approach

    Directory of Open Access Journals (Sweden)

    Anand Prakash

    2014-03-01

    Full Text Available Wireless Sensor Networks (WSNs with their dynamic applications gained a tremendous attention of researchers. Constant monitoring of critical situations attracted researchers to utilize WSNs at vast platforms. The main focus in WSNs is to enhance network localization as much as one could, for efficient and optimal utilization of resources. Different approaches based upon redundancy are proposed for optimum functionality. Localization is always related with redundancy of sensor nodes deployed at remote areas for constant and fault tolerant monitoring. In this work, we propose a comparison of classic flooding and the gossip protocol for homogenous networks which enhances stability and throughput quiet significantly.  

  6. Prediction based Greedy Perimeter Stateless Routing Protocol for Vehicular Self-organizing Network

    Science.gov (United States)

    Wang, Chunlin; Fan, Quanrun; Chen, Xiaolin; Xu, Wanjin

    2018-03-01

    PGPSR (Prediction based Greedy Perimeter Stateless Routing) is based on and extended the GPSR protocol to adapt to the high speed mobility of the vehicle auto organization network (VANET) and the changes in the network topology. GPSR is used in the VANET network environment, the network loss rate and throughput are not ideal, even cannot work. Aiming at the problems of the GPSR, the proposed PGPSR routing protocol, it redefines the hello and query packet structure, in the structure of the new node speed and direction information, which received the next update before you can take advantage of its speed and direction to predict the position of node and new network topology, select the right the next hop routing and path. Secondly, the update of the outdated node information of the neighbor’s table is deleted in time. The simulation experiment shows the performance of PGPSR is better than that of GPSR.

  7. PERFORMANCE ANALYSIS OF DSR ROUTING PROTOCOL UNDER ENERGY BASED SELFISH ATTACK IN MOBILE AD HOC NETWORKS

    Directory of Open Access Journals (Sweden)

    T.V.P.Sundararajan

    2010-06-01

    Full Text Available Mobile Ad hoc Networks (MANETs rely on the cooperation of all participating nodes to provide the fundamental operations such as routing and data forwarding. However, due to the open structure and scarcely available battery-based energy, node misbehaviors may exist.[1]. One such routing misbehavior is that some selfish nodes will participate in the route discovery and maintenance processes but refuse to forward data packets. This paper pointed out Energy based selfish nodes (EBSN where these selfish nodes tend to use the network but do not cooperate, saving battery life for their own communications [2],[3]. We present a simulation study of the effects of Energy based selfish nodes (EBSN on DSR routing protocol and its impact over network performance in terms of throughput and delay of a mobile ad hoc network where a defined percentage of nodes were misbehaving.

  8. An authenticated encrypted routing protocol against attacks in mobile ad-hoc networks

    Directory of Open Access Journals (Sweden)

    C.C. Suma

    2017-01-01

    Full Text Available Mobile Ad hoc Network is stated as a cluster that contains Digital data terminals and they are furnished with the wireless transceivers which are able to communicate with each other with no need of any fixed architecture or concentrated authority. Security is one of the major issues in MANETs because of vast applications such as Military Battlefields, emergency and rescue operations[10]. In order to provide anonymous communications and to identify the malicious nodes in MANETs, many authors have proposed different secure routing protocols but each protocol have their own advantages and disadvantages. In MANTE’s each and every node in the communicating network functions like router and transmits the packets among the networking nodes for the purpose of communication[11]. Sometimes nodes may be attacked by the malicious nodes or the legitimate node will be caught by foemen there by controlling and preventing the nodes to perform the assigned task or nodes may be corrupted due to loss of energy. So, due to these drawbacks securing the network under the presence of adversaries is an important thing. The existing protocols were designed with keeping anonymity and the identification of vicious nodes in the network as the main goal. For providing better security, the anonymity factors such as Unidentifiability and Unlinkability must be fully satisfied[1]. Many anonymous routing schemes that concentrate on achieving anonymity are proposed in the past decade and they provides the security at different levels and also provides the privacy protection that is of different cost. In this paper we consider a protocol called Authenticated Secure Routing Protocol proposed which provides both security & anonymity. Anonymity is achieved in this protocol using Group signature. Over all by using this protocol performance in terms of throughput as well as the packet dropping rate is good compared to the other living protocols.

  9. A Bypass-Ring Scheme for a Fault Tolerant Multicast

    Directory of Open Access Journals (Sweden)

    V. Dynda

    2003-01-01

    Full Text Available We present a fault tolerant scheme for recovery from single or multiple node failures in multi-directional multicast trees. The scheme is based on cyclic structures providing alternative paths to eliminate faulty nodes and reroute the traffic. Our scheme is independent of message source and direction in the tree, provides a basis for on-the-fly repair and can be used as a platform for various strategies for reconnecting tree partitions. It only requires an underlying infrastructure to provide a reliable routing service. Although it is described in the context of a message multicast, the scheme can be used universally in all systems using tree-based overlay networks for communication among components.

  10. Self-Adaptive Contention Aware Routing Protocol for Intermittently Connected Mobile Networks

    KAUST Repository

    Elwhishi, Ahmed

    2013-07-01

    This paper introduces a novel multicopy routing protocol, called Self-Adaptive Utility-based Routing Protocol (SAURP), for Delay Tolerant Networks (DTNs) that are possibly composed of a vast number of devices in miniature such as smart phones of heterogeneous capacities in terms of energy resources and buffer spaces. SAURP is characterized by the ability of identifying potential opportunities for forwarding messages to their destinations via a novel utility function-based mechanism, in which a suite of environment parameters, such as wireless channel condition, nodal buffer occupancy, and encounter statistics, are jointly considered. Thus, SAURP can reroute messages around nodes experiencing high-buffer occupancy, wireless interference, and/or congestion, while taking a considerably small number of transmissions. The developed utility function in SAURP is proved to be able to achieve optimal performance, which is further analyzed via a stochastic modeling approach. Extensive simulations are conducted to verify the developed analytical model and compare the proposed SAURP with a number of recently reported encounter-based routing approaches in terms of delivery ratio, delivery delay, and the number of transmissions required for each message delivery. The simulation results show that SAURP outperforms all the counterpart multicopy encounter-based routing protocols considered in the study.

  11. Self-Adaptive Contention Aware Routing Protocol for Intermittently Connected Mobile Networks

    KAUST Repository

    Elwhishi, Ahmed; Ho, Pin-Han; Naik, K.; Shihada, Basem

    2013-01-01

    This paper introduces a novel multicopy routing protocol, called Self-Adaptive Utility-based Routing Protocol (SAURP), for Delay Tolerant Networks (DTNs) that are possibly composed of a vast number of devices in miniature such as smart phones of heterogeneous capacities in terms of energy resources and buffer spaces. SAURP is characterized by the ability of identifying potential opportunities for forwarding messages to their destinations via a novel utility function-based mechanism, in which a suite of environment parameters, such as wireless channel condition, nodal buffer occupancy, and encounter statistics, are jointly considered. Thus, SAURP can reroute messages around nodes experiencing high-buffer occupancy, wireless interference, and/or congestion, while taking a considerably small number of transmissions. The developed utility function in SAURP is proved to be able to achieve optimal performance, which is further analyzed via a stochastic modeling approach. Extensive simulations are conducted to verify the developed analytical model and compare the proposed SAURP with a number of recently reported encounter-based routing approaches in terms of delivery ratio, delivery delay, and the number of transmissions required for each message delivery. The simulation results show that SAURP outperforms all the counterpart multicopy encounter-based routing protocols considered in the study.

  12. An Improved PRoPHET Routing Protocol in Delay Tolerant Network

    Directory of Open Access Journals (Sweden)

    Seung Deok Han

    2015-01-01

    Full Text Available In delay tolerant network (DTN, an end-to-end path is not guaranteed and packets are delivered from a source node to a destination node via store-carry-forward based routing. In DTN, a source node or an intermediate node stores packets in buffer and carries them while it moves around. These packets are forwarded to other nodes based on predefined criteria and finally are delivered to a destination node via multiple hops. In this paper, we improve the dissemination speed of PRoPHET (probability routing protocol using history of encounters and transitivity protocol by employing epidemic protocol for disseminating message m, if forwarding counter and hop counter values are smaller than or equal to the threshold values. The performance of the proposed protocol was analyzed from the aspect of delivery probability, average delay, and overhead ratio. Numerical results show that the proposed protocol can improve the delivery probability, average delay, and overhead ratio of PRoPHET protocol by appropriately selecting the threshold forwarding counter and threshold hop counter values.

  13. Cost-Effective Encryption-Based Autonomous Routing Protocol for Efficient and Secure Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Kashif Saleem

    2016-03-01

    Full Text Available The deployment of intelligent remote surveillance systems depends on wireless sensor networks (WSNs composed of various miniature resource-constrained wireless sensor nodes. The development of routing protocols for WSNs is a major challenge because of their severe resource constraints, ad hoc topology and dynamic nature. Among those proposed routing protocols, the biology-inspired self-organized secure autonomous routing protocol (BIOSARP involves an artificial immune system (AIS that requires a certain amount of time to build up knowledge of neighboring nodes. The AIS algorithm uses this knowledge to distinguish between self and non-self neighboring nodes. The knowledge-building phase is a critical period in the WSN lifespan and requires active security measures. This paper proposes an enhanced BIOSARP (E-BIOSARP that incorporates a random key encryption mechanism in a cost-effective manner to provide active security measures in WSNs. A detailed description of E-BIOSARP is presented, followed by an extensive security and performance analysis to demonstrate its efficiency. A scenario with E-BIOSARP is implemented in network simulator 2 (ns-2 and is populated with malicious nodes for analysis. Furthermore, E-BIOSARP is compared with state-of-the-art secure routing protocols in terms of processing time, delivery ratio, energy consumption, and packet overhead. The findings show that the proposed mechanism can efficiently protect WSNs from selective forwarding, brute-force or exhaustive key search, spoofing, eavesdropping, replaying or altering of routing information, cloning, acknowledgment spoofing, HELLO flood attacks, and Sybil attacks.

  14. SACFIR: SDN-Based Application-Aware Centralized Adaptive Flow Iterative Reconfiguring Routing Protocol for WSNs.

    Science.gov (United States)

    Aslam, Muhammad; Hu, Xiaopeng; Wang, Fan

    2017-12-13

    Smart reconfiguration of a dynamic networking environment is offered by the central control of Software-Defined Networking (SDN). Centralized SDN-based management architectures are capable of retrieving global topology intelligence and decoupling the forwarding plane from the control plane. Routing protocols developed for conventional Wireless Sensor Networks (WSNs) utilize limited iterative reconfiguration methods to optimize environmental reporting. However, the challenging networking scenarios of WSNs involve a performance overhead due to constant periodic iterative reconfigurations. In this paper, we propose the SDN-based Application-aware Centralized adaptive Flow Iterative Reconfiguring (SACFIR) routing protocol with the centralized SDN iterative solver controller to maintain the load-balancing between flow reconfigurations and flow allocation cost. The proposed SACFIR's routing protocol offers a unique iterative path-selection algorithm, which initially computes suitable clustering based on residual resources at the control layer and then implements application-aware threshold-based multi-hop report transmissions on the forwarding plane. The operation of the SACFIR algorithm is centrally supervised by the SDN controller residing at the Base Station (BS). This paper extends SACFIR to SDN-based Application-aware Main-value Centralized adaptive Flow Iterative Reconfiguring (SAMCFIR) to establish both proactive and reactive reporting. The SAMCFIR transmission phase enables sensor nodes to trigger direct transmissions for main-value reports, while in the case of SACFIR, all reports follow computed routes. Our SDN-enabled proposed models adjust the reconfiguration period according to the traffic burden on sensor nodes, which results in heterogeneity awareness, load-balancing and application-specific reconfigurations of WSNs. Extensive experimental simulation-based results show that SACFIR and SAMCFIR yield the maximum scalability, network lifetime and stability

  15. SACFIR: SDN-Based Application-Aware Centralized Adaptive Flow Iterative Reconfiguring Routing Protocol for WSNs

    Directory of Open Access Journals (Sweden)

    Muhammad Aslam

    2017-12-01

    Full Text Available Smart reconfiguration of a dynamic networking environment is offered by the central control of Software-Defined Networking (SDN. Centralized SDN-based management architectures are capable of retrieving global topology intelligence and decoupling the forwarding plane from the control plane. Routing protocols developed for conventional Wireless Sensor Networks (WSNs utilize limited iterative reconfiguration methods to optimize environmental reporting. However, the challenging networking scenarios of WSNs involve a performance overhead due to constant periodic iterative reconfigurations. In this paper, we propose the SDN-based Application-aware Centralized adaptive Flow Iterative Reconfiguring (SACFIR routing protocol with the centralized SDN iterative solver controller to maintain the load-balancing between flow reconfigurations and flow allocation cost. The proposed SACFIR’s routing protocol offers a unique iterative path-selection algorithm, which initially computes suitable clustering based on residual resources at the control layer and then implements application-aware threshold-based multi-hop report transmissions on the forwarding plane. The operation of the SACFIR algorithm is centrally supervised by the SDN controller residing at the Base Station (BS. This paper extends SACFIR to SDN-based Application-aware Main-value Centralized adaptive Flow Iterative Reconfiguring (SAMCFIR to establish both proactive and reactive reporting. The SAMCFIR transmission phase enables sensor nodes to trigger direct transmissions for main-value reports, while in the case of SACFIR, all reports follow computed routes. Our SDN-enabled proposed models adjust the reconfiguration period according to the traffic burden on sensor nodes, which results in heterogeneity awareness, load-balancing and application-specific reconfigurations of WSNs. Extensive experimental simulation-based results show that SACFIR and SAMCFIR yield the maximum scalability, network lifetime

  16. A Novel Load Balancing Scheme for Multipath Routing Protocol in MANET

    Directory of Open Access Journals (Sweden)

    Kokilamani Mounagurusamy

    2016-09-01

    Full Text Available The recent advancements in information and communication technology create a great demand for multipath routing protocols. In MANET, nodes can be arbitrarily located and can move freely at any given time. The topology of MANET can change rapidly and unpredictably. Because wireless link capacities are usually limited, congestion is possible in MANETs. Hence, balancing the load in a MANET is important since nodes with high load will deplete their batteries quickly, thereby increasing the probability of disconnecting or partitioning the network. To overcome these, the multipath protocol should be aware of load at route discovery phase. The main objective of the proposed article is to balance the load on a node and to extend the lifetime of the node due to the congestion, energy depletion and link failures. This article describes a novel load and congestion aware scheme called Path Efficient Ad-hoc On-demand Multipath Distance Vector (PE-AOMDV protocol to increase the performance of routing process in MANET in terms of congestion, end-to-end delay and load balancing. A new threshold value and a counter variable are introduced to limit the number of communication paths passing over a node in route discovery phase. For every new request the counter variable is incremented by one and the threshold value is compared to see whether the maximum number of connections has been reached or not. The proposed method is network simulator ns-2 and it is found that there is a significant improvement in the proposed scheme. It reduces the energy consumption, average end-to-end delay and normalized routing overhead. Also the proposed scheme increases packet delivery ratio, throughput and minimizes routing overheads.

  17. Performance Analysis of AODV Routing Protocol for Wireless Sensor Network based Smart Metering

    International Nuclear Information System (INIS)

    Farooq, Hasan; Jung, Low Tang

    2013-01-01

    Today no one can deny the need for Smart Grid and it is being considered as of utmost importance to upgrade outdated electric infrastructure to cope with the ever increasing electric load demand. Wireless Sensor Network (WSN) is considered a promising candidate for internetworking of smart meters with the gateway using mesh topology. This paper investigates the performance of AODV routing protocol for WSN based smart metering deployment. Three case studies are presented to analyze its performance based on four metrics of (i) Packet Delivery Ratio, (ii) Average Energy Consumption of Nodes (iii) Average End-End Delay and (iv) Normalized Routing Load.

  18. The deployment of routing protocols in distributed control plane of SDN.

    Science.gov (United States)

    Jingjing, Zhou; Di, Cheng; Weiming, Wang; Rong, Jin; Xiaochun, Wu

    2014-01-01

    Software defined network (SDN) provides a programmable network through decoupling the data plane, control plane, and application plane from the original closed system, thus revolutionizing the existing network architecture to improve the performance and scalability. In this paper, we learned about the distributed characteristics of Kandoo architecture and, meanwhile, improved and optimized Kandoo's two levels of controllers based on ideological inspiration of RCP (routing control platform). Finally, we analyzed the deployment strategies of BGP and OSPF protocol in a distributed control plane of SDN. The simulation results show that our deployment strategies are superior to the traditional routing strategies.

  19. A comprehensive survey of energy-aware routing protocols in wireless body area sensor networks.

    Science.gov (United States)

    Effatparvar, Mehdi; Dehghan, Mehdi; Rahmani, Amir Masoud

    2016-09-01

    Wireless body area sensor network is a special purpose wireless sensor network that, employing wireless sensor nodes in, on, or around the human body, makes it possible to measure biological parameters of a person for specific applications. One of the most fundamental concerns in wireless body sensor networks is accurate routing in order to send data promptly and properly, and therefore overcome some of the challenges. Routing protocols for such networks are affected by a large number of factors including energy, topology, temperature, posture, the radio range of sensors, and appropriate quality of service in sensor nodes. Since energy is highly important in wireless body area sensor networks, and increasing the network lifetime results in benefiting greatly from sensor capabilities, improving routing performance with reduced energy consumption presents a major challenge. This paper aims to study wireless body area sensor networks and the related routing methods. It also presents a thorough, comprehensive review of routing methods in wireless body area sensor networks from the perspective of energy. Furthermore, different routing methods affecting the parameter of energy will be classified and compared according to their advantages and disadvantages. In this paper, fundamental concepts of wireless body area sensor networks are provided, and then the advantages and disadvantages of these networks are investigated. Since one of the most fundamental issues in wireless body sensor networks is to perform routing so as to transmit data precisely and promptly, we discuss the same issue. As a result, we propose a classification of the available relevant literature with respect to the key challenge of energy in the routing process. With this end in view, all important papers published between 2000 and 2015 are classified under eight categories including 'Mobility-Aware', 'Thermal-Aware', 'Restriction of Location and Number of Relays', 'Link-aware', 'Cluster- and Tree

  20. The Deployment of Routing Protocols in Distributed Control Plane of SDN

    Directory of Open Access Journals (Sweden)

    Zhou Jingjing

    2014-01-01

    Full Text Available Software defined network (SDN provides a programmable network through decoupling the data plane, control plane, and application plane from the original closed system, thus revolutionizing the existing network architecture to improve the performance and scalability. In this paper, we learned about the distributed characteristics of Kandoo architecture and, meanwhile, improved and optimized Kandoo’s two levels of controllers based on ideological inspiration of RCP (routing control platform. Finally, we analyzed the deployment strategies of BGP and OSPF protocol in a distributed control plane of SDN. The simulation results show that our deployment strategies are superior to the traditional routing strategies.

  1. Protection switching for carrier ethernet multicast

    DEFF Research Database (Denmark)

    Ruepp, Sarah Renée; Wessing, Henrik; Berger, Michael Stübert

    2010-01-01

    This paper addresses network survivability for IPTV multicast transport in Carrier Ethernet networks. The impact of link failures is investigated and suggestions for intelligent multicast resilience schemes are proposed. In particular, functions of the multicast tree are integrated with the Carri...... recovery path length, recovery time, number of branch nodes and operational complexity. The integrated approach therefore shows significant potential to increase the QoE for IPTV users in case of network failures and recovery actions.......This paper addresses network survivability for IPTV multicast transport in Carrier Ethernet networks. The impact of link failures is investigated and suggestions for intelligent multicast resilience schemes are proposed. In particular, functions of the multicast tree are integrated with the Carrier...

  2. L2-LBMT: A Layered Load Balance Routing Protocol for underwater multimedia data transmission

    Science.gov (United States)

    Lv, Ze; Tang, Ruichun; Tao, Ye; Sun, Xin; Xu, Xiaowei

    2017-12-01

    Providing highly efficient underwater transmission of mass multimedia data is challenging due to the particularities of the underwater environment. Although there are many schemes proposed to optimize the underwater acoustic network communication protocols, from physical layer, data link layer, network layer to transport layer, the existing routing protocols for underwater wireless sensor network (UWSN) still cannot well deal with the problems in transmitting multimedia data because of the difficulties involved in high energy consumption, low transmission reliability or high transmission delay. It prevents us from applying underwater multimedia data to real-time monitoring of marine environment in practical application, especially in emergency search, rescue operation and military field. Therefore, the inefficient transmission of marine multimedia data has become a serious problem that needs to be solved urgently. In this paper, A Layered Load Balance Routing Protocol (L2-LBMT) is proposed for underwater multimedia data transmission. In L2-LBMT, we use layered and load-balance Ad Hoc Network to transmit data, and adopt segmented data reliable transfer (SDRT) protocol to improve the data transport reliability. And a 3-node variant of tornado (3-VT) code is also combined with the Ad Hoc Network to transmit little emergency data more quickly. The simulation results show that the proposed protocol can balance energy consumption of each node, effectively prolong the network lifetime and reduce transmission delay of marine multimedia data.

  3. Energy-Efficient Cluster Based Routing Protocol in Mobile Ad Hoc Networks Using Network Coding

    Directory of Open Access Journals (Sweden)

    Srinivas Kanakala

    2014-01-01

    Full Text Available In mobile ad hoc networks, all nodes are energy constrained. In such situations, it is important to reduce energy consumption. In this paper, we consider the issues of energy efficient communication in MANETs using network coding. Network coding is an effective method to improve the performance of wireless networks. COPE protocol implements network coding concept to reduce number of transmissions by mixing the packets at intermediate nodes. We incorporate COPE into cluster based routing protocol to further reduce the energy consumption. The proposed energy-efficient coding-aware cluster based routing protocol (ECCRP scheme applies network coding at cluster heads to reduce number of transmissions. We also modify the queue management procedure of COPE protocol to further improve coding opportunities. We also use an energy efficient scheme while selecting the cluster head. It helps to increase the life time of the network. We evaluate the performance of proposed energy efficient cluster based protocol using simulation. Simulation results show that the proposed ECCRP algorithm reduces energy consumption and increases life time of the network.

  4. Analysis of MD5 authentication in various routing protocols using simulation tools

    Science.gov (United States)

    Dinakaran, M.; Darshan, K. N.; Patel, Harsh

    2017-11-01

    Authentication being an important paradigm of security and Computer Networks require secure paths to make the flow of the data even more secure through some security protocols. So MD-5(Message Digest 5) helps in providing data integrity to the data being sent through it and authentication to the network devices. This paper gives a brief introduction to the MD-5, simulation of the networks by including MD-5 authentication using various routing protocols like OSPF, EIGRP and RIPv2. GNS3 is being used to simulate the scenarios. Analysis of the MD-5 authentication is done in the later sections of the paper.

  5. Energy Threshold-based Cluster Head Rotation for Routing Protocol in Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Hadi Raheem Ali

    2018-05-01

    Full Text Available Energy efficiency represents a fundamental issue in WSNs, since the network lifetime period entirely depends on the energy of sensor nodes, which are usually battery-operated. In this article, an unequal clustering-based routing protocol has been suggested, where parameters of energy, distance, and density are involved in the cluster head election. Besides, the sizes of clusters are unequal according to distance, energy, and density. Furthermore, the cluster heads are not changed every round unless the residual energy reaches a specific threshold of energy. The outcomes of the conducted simulation confirmed that the performance of the suggested protocol achieves improvement in energy efficiency.

  6. Performance Analysis of Routing Protocols in Ad-hoc and Sensor Networking Environments

    Directory of Open Access Journals (Sweden)

    L. Gavrilovska

    2009-06-01

    Full Text Available Ad-hoc and sensor networks are becoming an increasingly popular wireless networking concepts lately. This paper analyzes and compares prominent routing schemes in these networking environments. The knowledge obtained can serve users to better understand short range wireless network solutions thus leading to options for implementation in various scenarios. In addition, it should aid researchers develop protocol improvements reliable for the technologies of interest.

  7. Energy-Efficient Cluster Based Routing Protocol in Mobile Ad Hoc Networks Using Network Coding

    OpenAIRE

    Srinivas Kanakala; Venugopal Reddy Ananthula; Prashanthi Vempaty

    2014-01-01

    In mobile ad hoc networks, all nodes are energy constrained. In such situations, it is important to reduce energy consumption. In this paper, we consider the issues of energy efficient communication in MANETs using network coding. Network coding is an effective method to improve the performance of wireless networks. COPE protocol implements network coding concept to reduce number of transmissions by mixing the packets at intermediate nodes. We incorporate COPE into cluster based routing proto...

  8. Performance Analysis of the Enhanced DSR Routing Protocol for the Short Time Disconnected MANET to the OPNET Modeler

    Directory of Open Access Journals (Sweden)

    PAPAJ Ján

    2013-05-01

    Full Text Available Disconnected mobile ad-hoc networks (MANET are very important areas of the research. In this article, the performance analysis of the enhanced dynamic source routing protocol (OPP_DSR is introduced. This modification enables the routing process in the case when there are no connections to other mobile nodes. It also will enable the routing mechanisms when the routes, selected by routing mechanisms, are disconnected for some time. Disconnection can be for a short time and standard routing protocol DSR cannot reflect on this situation.The main idea is based on opportunistic forwarding where the nodes not only forward data but it's stored in the cache during long time. The network parameters throughput, routing load and are analysed.

  9. A Game Theory-Based Obstacle Avoidance Routing Protocol for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Shujun Bi

    2011-09-01

    Full Text Available The obstacle avoidance problem in geographic forwarding is an important issue for location-based routing in wireless sensor networks. The presence of an obstacle leads to several geographic routing problems such as excessive energy consumption and data congestion. Obstacles are hard to avoid in realistic environments. To bypass obstacles, most routing protocols tend to forward packets along the obstacle boundaries. This leads to a situation where the nodes at the boundaries exhaust their energy rapidly and the obstacle area is diffused. In this paper, we introduce a novel routing algorithm to solve the obstacle problem in wireless sensor networks based on a game-theory model. Our algorithm forms a concave region that cannot forward packets to achieve the aim of improving the transmission success rate and decreasing packet transmission delays. We consider the residual energy, out-degree and forwarding angle to determine the forwarding probability and payoff function of forwarding candidates. This achieves the aim of load balance and reduces network energy consumption. Simulation results show that based on the average delivery delay, energy consumption and packet delivery ratio performances our protocol is superior to other traditional schemes.

  10. An Efficient Data-Gathering Routing Protocol for Underwater Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Nadeem Javaid

    2015-11-01

    Full Text Available Most applications of underwater wireless sensor networks (UWSNs demand reliable data delivery over a longer period in an efficient and timely manner. However, the harsh and unpredictable underwater environment makes routing more challenging as compared to terrestrial WSNs. Most of the existing schemes deploy mobile sensors or a mobile sink (MS to maximize data gathering. However, the relatively high deployment cost prevents their usage in most applications. Thus, this paper presents an autonomous underwater vehicle (AUV-aided efficient data-gathering (AEDG routing protocol for reliable data delivery in UWSNs. To prolong the network lifetime, AEDG employs an AUV for data collection from gateways and uses a shortest path tree (SPT algorithm while associating sensor nodes with the gateways. The AEDG protocol also limits the number of associated nodes with the gateway nodes to minimize the network energy consumption and to prevent the gateways from overloading. Moreover, gateways are rotated with the passage of time to balance the energy consumption of the network. To prevent data loss, AEDG allows dynamic data collection at the AUV depending on the limited number of member nodes that are associated with each gateway. We also develop a sub-optimal elliptical trajectory of AUV by using a connected dominating set (CDS to further facilitate network throughput maximization. The performance of the AEDG is validated via simulations, which demonstrate the effectiveness of AEDG in comparison to two existing UWSN routing protocols in terms of the selected performance metrics.

  11. An Efficient Data-Gathering Routing Protocol for Underwater Wireless Sensor Networks.

    Science.gov (United States)

    Javaid, Nadeem; Ilyas, Naveed; Ahmad, Ashfaq; Alrajeh, Nabil; Qasim, Umar; Khan, Zahoor Ali; Liaqat, Tayyaba; Khan, Majid Iqbal

    2015-11-17

    Most applications of underwater wireless sensor networks (UWSNs) demand reliable data delivery over a longer period in an efficient and timely manner. However, the harsh and unpredictable underwater environment makes routing more challenging as compared to terrestrial WSNs. Most of the existing schemes deploy mobile sensors or a mobile sink (MS) to maximize data gathering. However, the relatively high deployment cost prevents their usage in most applications. Thus, this paper presents an autonomous underwater vehicle (AUV)-aided efficient data-gathering (AEDG) routing protocol for reliable data delivery in UWSNs. To prolong the network lifetime, AEDG employs an AUV for data collection from gateways and uses a shortest path tree (SPT) algorithm while associating sensor nodes with the gateways. The AEDG protocol also limits the number of associated nodes with the gateway nodes to minimize the network energy consumption and to prevent the gateways from overloading. Moreover, gateways are rotated with the passage of time to balance the energy consumption of the network. To prevent data loss, AEDG allows dynamic data collection at the AUV depending on the limited number of member nodes that are associated with each gateway. We also develop a sub-optimal elliptical trajectory of AUV by using a connected dominating set (CDS) to further facilitate network throughput maximization. The performance of the AEDG is validated via simulations, which demonstrate the effectiveness of AEDG in comparison to two existing UWSN routing protocols in terms of the selected performance metrics.

  12. ADAPTIVE CLUSTER BASED ROUTING PROTOCOL WITH ANT COLONY OPTIMIZATION FOR MOBILE AD-HOC NETWORK IN DISASTER AREA

    Directory of Open Access Journals (Sweden)

    Enrico Budianto

    2012-07-01

    Full Text Available In post-disaster rehabilitation efforts, the availability of telecommunication facilities takes important role. However, the process to improve telecommunication facilities in disaster area is risky if it is done by humans. Therefore, a network method that can work efficiently, effectively, and capable to reach the widest possible area is needed. This research introduces a cluster-based routing protocol named Adaptive Cluster Based Routing Protocol (ACBRP equipped by Ant Colony Optimization method, and its implementation in a simulator developed by author. After data analysis and statistical tests, it can be concluded that routing protocol ACBRP performs better than AODV and DSR routing protocol. Pada upaya rehabilitasi pascabencana, ketersediaan fasilitas telekomunikasi memiliki peranan yang sangat penting. Namun, proses untuk memperbaiki fasilitas telekomunikasi di daerah bencana memiliki resiko jika dilakukan oleh manusia. Oleh karena itu, metode jaringan yang dapat bekerja secara efisien, efektif, dan mampu mencapai area seluas mungkin diperlukan. Penelitian ini memperkenalkan sebuah protokol routing berbasis klaster bernama Adaptive Cluster Based Routing Protocol (ACBRP, yang dilengkapi dengan metode Ant Colony Optimization, dan diimplementasikan pada simulator yang dikembangkan penulis. Setelah data dianalisis dan dilakukan uji statistik, disimpulkan bahwa protokol routing ACBRP beroperasi lebih baik daripada protokol routing AODV maupun DSR.

  13. A lightweight neighbor-info-based routing protocol for no-base-station taxi-call system.

    Science.gov (United States)

    Zhu, Xudong; Wang, Jinhang; Chen, Yunchao

    2014-01-01

    Since the quick topology change and short connection duration, the VANET has had unstable routing and wireless signal quality. This paper proposes a kind of lightweight routing protocol-LNIB for call system without base station, which is applicable to the urban taxis. LNIB maintains and predicts neighbor information dynamically, thus finding the reliable path between the source and the target. This paper describes the protocol in detail and evaluates the performance of this protocol by simulating under different nodes density and speed. The result of evaluation shows that the performance of LNIB is better than AODV which is a classic protocol in taxi-call scene.

  14. A routing protocol based on energy and link quality for Internet of Things applications.

    Science.gov (United States)

    Machado, Kássio; Rosário, Denis; Cerqueira, Eduardo; Loureiro, Antonio A F; Neto, Augusto; Souza, José Neuman de

    2013-02-04

    The Internet of Things (IoT) is attracting considerable attention from the universities, industries, citizens and governments for applications, such as healthcare, environmental monitoring and smart buildings. IoT enables network connectivity between smart devices at all times, everywhere, and about everything. In this context, Wireless Sensor Networks (WSNs) play an important role in increasing the ubiquity of networks with smart devices that are low-cost and easy to deploy. However, sensor nodes are restricted in terms of energy, processing and memory. Additionally, low-power radios are very sensitive to noise, interference and multipath distortions. In this context, this article proposes a routing protocol based on Routing by Energy and Link quality (REL) for IoT applications. To increase reliability and energy-efficiency, REL selects routes on the basis of a proposed end-to-end link quality estimator mechanism, residual energy and hop count. Furthermore, REL proposes an event-driven mechanism to provide load balancing and avoid the premature energy depletion of nodes/networks. Performance evaluations were carried out using simulation and testbed experiments to show the impact and benefits of REL in small and large-scale networks. The results show that REL increases the network lifetime and services availability, as well as the quality of service of IoT applications. It also provides an even distribution of scarce network resources and reduces the packet loss rate, compared with the performance of well-known protocols.

  15. A Routing Protocol Based on Energy and Link Quality for Internet of Things Applications

    Directory of Open Access Journals (Sweden)

    Antonio A. F. Loureiro

    2013-02-01

    Full Text Available The Internet of Things (IoT is attracting considerable attention from the universities, industries, citizens and governments for applications, such as healthcare, environmental monitoring and smart buildings. IoT enables network connectivity between smart devices at all times, everywhere, and about everything. In this context, Wireless Sensor Networks (WSNs play an important role in increasing the ubiquity of networks with smart devices that are low-cost and easy to deploy. However, sensor nodes are restricted in terms of energy, processing and memory. Additionally, low-power radios are very sensitive to noise, interference and multipath distortions. In this context, this article proposes a routing protocol based on Routing by Energy and Link quality (REL for IoT applications. To increase reliability and energy-efficiency, REL selects routes on the basis of a proposed end-to-end link quality estimator mechanism, residual energy and hop count. Furthermore, REL proposes an event-driven mechanism to provide load balancing and avoid the premature energy depletion of nodes/networks. Performance evaluations were carried out using simulation and testbed experiments to show the impact and benefits of REL in small and large-scale networks. The results show that REL increases the network lifetime and services availability, as well as the quality of service of IoT applications. It also provides an even distribution of scarce network resources and reduces the packet loss rate, compared with the performance of well-known protocols.

  16. A Routing Protocol Based on Energy and Link Quality for Internet of Things Applications

    Science.gov (United States)

    Machado, Kassio; Rosário, Denis; Cerqueira, Eduardo; Loureiro, Antonio A. F.; Neto, Augusto; de Souza, José Neuman

    2013-01-01

    The Internet of Things (IoT) is attracting considerable attention from the universities, industries, citizens and governments for applications, such as healthcare,environmental monitoring and smart buildings. IoT enables network connectivity between smart devices at all times, everywhere, and about everything. In this context, Wireless Sensor Networks (WSNs) play an important role in increasing the ubiquity of networks with smart devices that are low-cost and easy to deploy. However, sensor nodes are restricted in terms of energy, processing and memory. Additionally, low-power radios are very sensitive to noise, interference and multipath distortions. In this context, this article proposes a routing protocol based on Routing by Energy and Link quality (REL) for IoT applications. To increase reliability and energy-efficiency, REL selects routes on the basis of a proposed end-to-end link quality estimator mechanism, residual energy and hop count. Furthermore, REL proposes an event-driven mechanism to provide load balancing and avoid the premature energy depletion of nodes/networks. Performance evaluations were carried out using simulation and testbed experiments to show the impact and benefits of REL in small and large-scale networks. The results show that REL increases the network lifetime and services availability, as well as the quality of service of IoT applications. It also provides an even distribution of scarce network resources and reduces the packet loss rate, compared with the performance of well-known protocols. PMID:23385410

  17. Routing protocol for wireless quantum multi-hop mesh backbone network based on partially entangled GHZ state

    Science.gov (United States)

    Xiong, Pei-Ying; Yu, Xu-Tao; Zhang, Zai-Chen; Zhan, Hai-Tao; Hua, Jing-Yu

    2017-08-01

    Quantum multi-hop teleportation is important in the field of quantum communication. In this study, we propose a quantum multi-hop communication model and a quantum routing protocol with multihop teleportation for wireless mesh backbone networks. Based on an analysis of quantum multi-hop protocols, a partially entangled Greenberger-Horne-Zeilinger (GHZ) state is selected as the quantum channel for the proposed protocol. Both quantum and classical wireless channels exist between two neighboring nodes along the route. With the proposed routing protocol, quantum information can be transmitted hop by hop from the source node to the destination node. Based on multi-hop teleportation based on the partially entangled GHZ state, a quantum route established with the minimum number of hops. The difference between our routing protocol and the classical one is that in the former, the processes used to find a quantum route and establish quantum channel entanglement occur simultaneously. The Bell state measurement results of each hop are piggybacked to quantum route finding information. This method reduces the total number of packets and the magnitude of air interface delay. The deduction of the establishment of a quantum channel between source and destination is also presented here. The final success probability of quantum multi-hop teleportation in wireless mesh backbone networks was simulated and analyzed. Our research shows that quantum multi-hop teleportation in wireless mesh backbone networks through a partially entangled GHZ state is feasible.

  18. Discrete Particle Swarm Optimization Routing Protocol for Wireless Sensor Networks with Multiple Mobile Sinks.

    Science.gov (United States)

    Yang, Jin; Liu, Fagui; Cao, Jianneng; Wang, Liangming

    2016-07-14

    Mobile sinks can achieve load-balancing and energy-consumption balancing across the wireless sensor networks (WSNs). However, the frequent change of the paths between source nodes and the sinks caused by sink mobility introduces significant overhead in terms of energy and packet delays. To enhance network performance of WSNs with mobile sinks (MWSNs), we present an efficient routing strategy, which is formulated as an optimization problem and employs the particle swarm optimization algorithm (PSO) to build the optimal routing paths. However, the conventional PSO is insufficient to solve discrete routing optimization problems. Therefore, a novel greedy discrete particle swarm optimization with memory (GMDPSO) is put forward to address this problem. In the GMDPSO, particle's position and velocity of traditional PSO are redefined under discrete MWSNs scenario. Particle updating rule is also reconsidered based on the subnetwork topology of MWSNs. Besides, by improving the greedy forwarding routing, a greedy search strategy is designed to drive particles to find a better position quickly. Furthermore, searching history is memorized to accelerate convergence. Simulation results demonstrate that our new protocol significantly improves the robustness and adapts to rapid topological changes with multiple mobile sinks, while efficiently reducing the communication overhead and the energy consumption.

  19. Multi-Gateway-Based Energy Holes Avoidance Routing Protocol for WSN

    Directory of Open Access Journals (Sweden)

    Rohini Sharma

    2016-04-01

    Full Text Available In wireless sensor networks (WSNs, efficient energy conservation is required to prolong the lifetime of the network. In this work, we have given emphasis on balanced energy consumption and energy holes avoidance. This paper proposes a multi-gateway-based approach to reduce the transmission distance between the sender and the sink node. The area to be monitored is divided into regions and gateway nodes are deployed at optimal positions. We have designed a transmission scheme, in which sensors in the sink region communicate directly to the sink, sensors in the gateway region communicate directly to the gateway, and sensors in the cluster region transmit their data directly to their respective cluster head which transmits data to the gateway in its region. If the distance between a cluster head and the sink is less than the distance between the cluster head and the gateway node, the cluster head transmits data to the sink instead of the gateway node. We have compared the proposed protocol with Low-Energy Adaptive Clustering Hierarchy (LEACH, Gateway Based Energy Aware Multi-Hop Routing (M-GEAR, and Gateway Based Stable Election Protocol (GSEP protocols. The protocol performs better than other protocols in terms of throughput, stability period, lifetime, residual energy, and the packet transmitted to the sink.

  20. Modeling and Simulation of a Novel Relay Node Based Secure Routing Protocol Using Multiple Mobile Sink for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Madhumathy Perumal

    2015-01-01

    Full Text Available Data gathering and optimal path selection for wireless sensor networks (WSN using existing protocols result in collision. Increase in collision further increases the possibility of packet drop. Thus there is a necessity to eliminate collision during data aggregation. Increasing the efficiency is the need of the hour with maximum security. This paper is an effort to come up with a reliable and energy efficient WSN routing and secure protocol with minimum delay. This technique is named as relay node based secure routing protocol for multiple mobile sink (RSRPMS. This protocol finds the rendezvous point for optimal transmission of data using a “splitting tree” technique in tree-shaped network topology and then to determine all the subsequent positions of a sink the “Biased Random Walk” model is used. In case of an event, the sink gathers the data from all sources, when they are in the sensing range of rendezvous point. Otherwise relay node is selected from its neighbor to transfer packets from rendezvous point to sink. A symmetric key cryptography is used for secure transmission. The proposed relay node based secure routing protocol for multiple mobile sink (RSRPMS is experimented and simulation results are compared with Intelligent Agent-Based Routing (IAR protocol to prove that there is increase in the network lifetime compared with other routing protocols.

  1. Improvement over the OLSR Routing Protocol in Mobile Ad Hoc Networks by Eliminating the Unnecessary Loops

    OpenAIRE

    Shahram Behzad; Reza Fotohi; Shahram Jamali

    2013-01-01

    Mobile ad hoc networks are type of wireless networks in which any kind of infrastructure is not used, i.e. there are no infrastructures such as routers or switches or anything else on the network that can be used to support the network structure and the nodes has mobility. The purpose of this paper is to provide a better quality of the package delivery rate and the throughput, that is in need of powerful routing protocol standards, which can guarantee delivering of the packages to destination...

  2. Power Management Based Grid Routing Protocol for IEEE 802.11 Based MANET

    Institute of Scientific and Technical Information of China (English)

    XU Li; ZHENG Bao-yu; YANG Zhen

    2004-01-01

    MANET ( Mobile Ad Hoc Network ) is a collection of wireless mobile nodes forming a temporary communication network without the aid of any established infrastructure or centralized administration. The lifetime of a MANET depends on the battery resources of the mobile nodes. So energy consumption may one of important design criterions for MANET. With changing the idle model to sleep model in the grid environment, this paper proposes a new energy-aware routing protocol. Performance simulation results show that the proposed strategy can dynamic balance the traffic load inside the whole network, extend the lifetime of a MANET, and without decreasing the throughput ratio.

  3. 移动Ad Hoc网络路由协议综述%A Survey of Routing Protocols for Mobile Ad Hoc Networks

    Institute of Scientific and Technical Information of China (English)

    张顺亮; 叶澄清; 李方敏

    2003-01-01

    A review of current research about routing protocols for mobile Ad Hoc networks is made. Based on classifying of them, the characteristic, the strength and the weakness of these protocols are evaluated respectively. Then some crucial strategies to improve the existing routing protocols are proposed. Besides, a frame of new routing protocol for Ad Hoc networks is put forward. Finally, open issues that still need investigation are listed.

  4. A Novel Video Data-Source Authentication Model Based on Digital Watermarking and MAC in Multicast

    Institute of Scientific and Technical Information of China (English)

    ZHAO Anjun; LU Xiangli; GUO Lei

    2006-01-01

    A novel video data authentication model based on digital video watermarking and MAC (message authentication code) in multicast protocol is proposed in this paper. The digital watermarking which composes of the MAC of the significant video content, the key and instant authentication data is embedded into the insignificant video component by the MLUT (modified look-up table) video watermarking technology. We explain a method that does not require storage of each data packet for a time, thus making receiver not vulnerable to DOS (denial of service) attack. So the video packets can be authenticated instantly without large volume buffer in the receivers. TESLA(timed efficient stream loss-tolerant authentication) does not explain how to select the suitable value for d, which is an important parameter in multicast source authentication. So we give a method to calculate the key disclosure delay (number of intervals). Simulation results show that the proposed algorithms improve the performance of data source authentication in multicast.

  5. QoS and energy aware cooperative routing protocol for wildfire monitoring wireless sensor networks.

    Science.gov (United States)

    Maalej, Mohamed; Cherif, Sofiane; Besbes, Hichem

    2013-01-01

    Wireless sensor networks (WSN) are presented as proper solution for wildfire monitoring. However, this application requires a design of WSN taking into account the network lifetime and the shadowing effect generated by the trees in the forest environment. Cooperative communication is a promising solution for WSN which uses, at each hop, the resources of multiple nodes to transmit its data. Thus, by sharing resources between nodes, the transmission quality is enhanced. In this paper, we use the technique of reinforcement learning by opponent modeling, optimizing a cooperative communication protocol based on RSSI and node energy consumption in a competitive context (RSSI/energy-CC), that is, an energy and quality-of-service aware-based cooperative communication routing protocol. Simulation results show that the proposed algorithm performs well in terms of network lifetime, packet delay, and energy consumption.

  6. A Routing Protocol Based on Received Signal Strength for Underwater Wireless Sensor Networks (UWSNs

    Directory of Open Access Journals (Sweden)

    Meiju Li

    2017-11-01

    Full Text Available Underwater wireless sensor networks (UWSNs are featured by long propagation delay, limited energy, narrow bandwidth, high BER (Bit Error Rate and variable topology structure. These features make it very difficult to design a short delay and high energy-efficiency routing protocol for UWSNs. In this paper, a routing protocol independent of location information is proposed based on received signal strength (RSS, which is called RRSS. In RRSS, a sensor node firstly establishes a vector from the node to a sink node; the length of the vector indicates the RSS of the beacon signal (RSSB from the sink node. A node selects the next-hop along the vector according to RSSB and the RSS of a hello packet (RSSH. The node nearer to the vector has higher priority to be a candidate next-hop. To avoid data packets being delivered to the neighbor nodes in a void area, a void-avoiding algorithm is introduced. In addition, residual energy is considered when selecting the next-hop. Meanwhile, we establish mathematic models to analyze the robustness and energy efficiency of RRSS. Lastly, we conduct extensive simulations, and the simulation results show RRSS can save energy consumption and decrease end-to-end delay.

  7. A Time-Slotted On-Demand Routing Protocol for Mobile Ad Hoc Unmanned Vehicle Systems

    Energy Technology Data Exchange (ETDEWEB)

    Hope Forsmann; Robert Hiromoto; John Svoboda

    2007-04-01

    The popularity of UAVs has increased dramatically because of their successful deployment in military operations, their ability to preserve human life, and the continual improvements in wireless communication that serves to increase their capabilities. We believe the usefulness of UAVs would be dramatically increased if formation flight were added to the list of capabilities. Currently, sustained formation flight with a cluster of UAVs has only been achieved with two nodes by the Multi-UAV Testbed at the Massachusetts Institute of Technology. (Park, 2004) Formation flight is a complex operation requiring the ability to adjust the flight patterns on the fly and correct for wind gusts, terrain, and differences in node equipment. All of which increases the amount of inner node communication. Since one of the problems with MANET communication is network congestion, we believe a first step towards formation flight can be made through improved inner node communication. We have investigated current communication routing protocols and developed an altered hybrid routing protocol in order to provide communication with less network congestion.

  8. Fundamental Lifetime Mechanisms in Routing Protocols for Wireless Sensor Networks: A Survey and Open Issues

    Science.gov (United States)

    Eslaminejad, Mohammadreza; Razak, Shukor Abd

    2012-01-01

    Wireless sensor networks basically consist of low cost sensor nodes which collect data from environment and relay them to a sink, where they will be subsequently processed. Since wireless nodes are severely power-constrained, the major concern is how to conserve the nodes' energy so that network lifetime can be extended significantly. Employing one static sink can rapidly exhaust the energy of sink neighbors. Furthermore, using a non-optimal single path together with a maximum transmission power level may quickly deplete the energy of individual nodes on the route. This all results in unbalanced energy consumption through the sensor field, and hence a negative effect on the network lifetime. In this paper, we present a comprehensive taxonomy of the various mechanisms applied for increasing the network lifetime. These techniques, whether in the routing or cross-layer area, fall within the following types: multi-sink, mobile sink, multi-path, power control and bio-inspired algorithms, depending on the protocol operation. In this taxonomy, special attention has been devoted to the multi-sink, power control and bio-inspired algorithms, which have not yet received much consideration in the literature. Moreover, each class covers a variety of the state-of-the-art protocols, which should provide ideas for potential future works. Finally, we compare these mechanisms and discuss open research issues. PMID:23202008

  9. Safety of adenosine stress myocardial perfusion imaging by a one-route infusion protocol

    International Nuclear Information System (INIS)

    Kawai, Yuko; Kishino, Koh

    2006-01-01

    When adenosine stress testing is performed, a vein is generally accessed in each arm. To determine whether the one-route infusion protocol, that is, infusion via one upper arm vein, is safe, myocardial perfusion imaging was performed during adenosine stress testing in patients with angina pectoris. Sixty-six consecutive patients (43 men, 68±11 years of age) with suspected coronary artery disease were enrolled in this study. For the stress test, adenosine was injected at 120 μg/kg/min for 6 minutes. Systolic blood pressure, diastolic blood pressure, and heart rate did not show any significant changes after injection of the adenosine and radioisotope (RI) tracer. Adverse events during infusion of the adenosine were seen in 42 (64%) patients and included chest discomfort/oppression in 17 (26%) and dyspnea/throat discomfort in 15 (23%). On the other hand, adverse events just after infusion of the RI tracer occurred in 5 (8%) patients and included chest oppression in 2 (3%) and dyspnea in 1 (2%). Almost all adverse events disappeared quickly without treatment. Therefore, we concluded that adenosine stress myocardial perfusion imaging using a one-route infusion protocol is safe and useful to do for patients unable to secure veins in both arms. (author)

  10. Data-Based Energy Efficient Clustered Routing Protocol for Wireless Sensors Networks – Tabuk Flood Monitoring System Case Study

    Directory of Open Access Journals (Sweden)

    Ammar Babiker

    2017-10-01

    Full Text Available Energy efficiency has been considered as the most important issue in wireless sensor networks. As in many applications, wireless sensors are scattered in a wide harsh area, where the battery replacement or charging will be quite difficult and it is the most important challenge. Therefore, the design of energy saving mechanism becomes mandatory in most recent research. In this paper, a new energy efficient clustered routing protocol is proposed: the proposed protocol is based on analyzing the data collected from the sensors in a base-station. Based on this analysis the cluster head will be selected as the one with the most useful data. Then, a variable time slot is specified to each sensor to minimize the transmission of repetitive and un-useful data. The proposed protocol Data-Based Energy Efficient Clustered Routing Protocol for Wireless Sensors Networks (DCRP was compared with the famous energy efficient LEACH protocol and also with one of the recent energy efficient routing protocols named Position Responsive Routing Protocol (PRRP. DCRP has been used in monitoring the floods in Tabuk area –Saudi Arabia. It shows comparatively better results.

  11. A Multipath Routing Protocol Based on Clustering and Ant Colony Optimization for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Jing Yang

    2010-05-01

    Full Text Available For monitoring burst events in a kind of reactive wireless sensor networks (WSNs, a multipath routing protocol (MRP based on dynamic clustering and ant colony optimization (ACO is proposed.. Such an approach can maximize the network lifetime and reduce the energy consumption. An important attribute of WSNs is their limited power supply, and therefore some metrics (such as energy consumption of communication among nodes, residual energy, path length were considered as very important criteria while designing routing in the MRP. Firstly, a cluster head (CH is selected among nodes located in the event area according to some parameters, such as residual energy. Secondly, an improved ACO algorithm is applied in the search for multiple paths between the CH and sink node. Finally, the CH dynamically chooses a route to transmit data with a probability that depends on many path metrics, such as energy consumption. The simulation results show that MRP can prolong the network lifetime, as well as balance of energy consumption among nodes and reduce the average energy consumption effectively.

  12. ENERGY EFFICIENT ROUTING PROTOCOLS FOR WIRELESS AD HOC NETWORKS – A SURVEY

    Directory of Open Access Journals (Sweden)

    K. Sankar

    2012-06-01

    Full Text Available Reducing energy consumption, primarily with the goal of extending the lifetime of battery-powered devices, has emerged as a fundamental challenge in wireless communication. The performance of the medium access control (MAC scheme not only has a fairly significant end-result on the behaviour of the routing approach employed, but also on the energy consumption of the wireless network interface card (NIC. We investigate the inadequacies of the MAC schemes designed for ad hoc wireless networks in the context of power awareness herein. The topology changes due to uncontrollable factors such as node mobility, weather, interference, noise, as well as on controllable parameters such as transmission power and antenna direction results in significant amount of energy loss. Controlling rapid topology changes by minimizing the maximum transmission power used in ad hoc wireless networks, while still maintaining networks connectivity can prolong battery life and hence network lifetime considerably. In addition, we systematically explore the potential energy consumption pitfalls of non–power-based and power based routing schemes. We suggest a thorough energy-based performance survey of energy aware routing protocols for wireless mobile ad-hoc networks. We also present the statistical performance metrics measured by our simulations.

  13. Sink-to-Sink Coordination Framework Using RPL: Routing Protocol for Low Power and Lossy Networks

    Directory of Open Access Journals (Sweden)

    Meer M. Khan

    2016-01-01

    Full Text Available RPL (Routing Protocol for low power and Lossy networks is recommended by Internet Engineering Task Force (IETF for IPv6-based LLNs (Low Power and Lossy Networks. RPL uses a proactive routing approach and each node always maintains an active path to the sink node. Sink-to-sink coordination defines syntax and semantics for the exchange of any network defined parameters among sink nodes like network size, traffic load, mobility of a sink, and so forth. The coordination allows sink to learn about the network condition of neighboring sinks. As a result, sinks can make coordinated decision to increase/decrease their network size for optimizing over all network performance in terms of load sharing, increasing network lifetime, and lowering end-to-end latency of communication. Currently, RPL does not provide any coordination framework that can define message exchange between different sink nodes for enhancing the network performance. In this paper, a sink-to-sink coordination framework is proposed which utilizes the periodic route maintenance messages issued by RPL to exchange network status observed at a sink with its neighboring sinks. The proposed framework distributes network load among sink nodes for achieving higher throughputs and longer network’s life time.

  14. CENTERA: A Centralized Trust-Based Efficient Routing Protocol with Authentication for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Ayman Tajeddine

    2015-02-01

    Full Text Available In this paper, we present CENTERA, a CENtralized Trust-based Efficient Routing protocol with an appropriate authentication scheme for wireless sensor networks (WSN. CENTERA utilizes the more powerful base station (BS to gather minimal neighbor trust information from nodes and calculate the best routes after isolating different types of “bad” nodes. By periodically accumulating these simple local observations and approximating the nodes’ battery lives, the BS draws a global view of the network, calculates three quality metrics—maliciousness, cooperation, and compatibility—and evaluates the Data Trust and Forwarding Trust values of each node. Based on these metrics, the BS isolates “bad”, “misbehaving” or malicious nodes for a certain period, and put some nodes on probation. CENTERA increases the node’s bad/probation level with repeated “bad” behavior, and decreases it otherwise. Then it uses a very efficient method to distribute the routing information to “good” nodes. Based on its target environment, and if required, CENTERA uses an authentication scheme suitable for severely constrained nodes, ranging from the symmetric RC5 for safe environments under close administration, to pairing-based cryptography (PBC for hostile environments with a strong attacker model. We simulate CENTERA using TOSSIM and verify its correctness and show some energy calculations.

  15. CENTERA: A Centralized Trust-Based Efficient Routing Protocol with Authentication for Wireless Sensor Networks †

    Science.gov (United States)

    Tajeddine, Ayman; Kayssi, Ayman; Chehab, Ali; Elhajj, Imad; Itani, Wassim

    2015-01-01

    In this paper, we present CENTERA, a CENtralized Trust-based Efficient Routing protocol with an appropriate authentication scheme for wireless sensor networks (WSN). CENTERA utilizes the more powerful base station (BS) to gather minimal neighbor trust information from nodes and calculate the best routes after isolating different types of “bad” nodes. By periodically accumulating these simple local observations and approximating the nodes' battery lives, the BS draws a global view of the network, calculates three quality metrics—maliciousness, cooperation, and compatibility—and evaluates the Data Trust and Forwarding Trust values of each node. Based on these metrics, the BS isolates “bad”, “misbehaving” or malicious nodes for a certain period, and put some nodes on probation. CENTERA increases the node's bad/probation level with repeated “bad” behavior, and decreases it otherwise. Then it uses a very efficient method to distribute the routing information to “good” nodes. Based on its target environment, and if required, CENTERA uses an authentication scheme suitable for severely constrained nodes, ranging from the symmetric RC5 for safe environments under close administration, to pairing-based cryptography (PBC) for hostile environments with a strong attacker model. We simulate CENTERA using TOSSIM and verify its correctness and show some energy calculations. PMID:25648712

  16. CENTERA: a centralized trust-based efficient routing protocol with authentication for wireless sensor networks.

    Science.gov (United States)

    Tajeddine, Ayman; Kayssi, Ayman; Chehab, Ali; Elhajj, Imad; Itani, Wassim

    2015-02-02

    In this paper, we present CENTERA, a CENtralized Trust-based Efficient Routing protocol with an appropriate authentication scheme for wireless sensor networks (WSN). CENTERA utilizes the more powerful base station (BS) to gather minimal neighbor trust information from nodes and calculate the best routes after isolating different types of "bad" nodes. By periodically accumulating these simple local observations and approximating the nodes' battery lives, the BS draws a global view of the network, calculates three quality metrics-maliciousness, cooperation, and compatibility-and evaluates the Data Trust and Forwarding Trust values of each node. Based on these metrics, the BS isolates "bad", "misbehaving" or malicious nodes for a certain period, and put some nodes on probation. CENTERA increases the node's bad/probation level with repeated "bad" behavior, and decreases it otherwise. Then it uses a very efficient method to distribute the routing information to "good" nodes. Based on its target environment, and if required, CENTERA uses an authentication scheme suitable for severely constrained nodes, ranging from the symmetric RC5 for safe environments under close administration, to pairing-based cryptography (PBC) for hostile environments with a strong attacker model. We simulate CENTERA using TOSSIM and verify its correctness and show some energy calculations.

  17. DOW-PR DOlphin and Whale Pods Routing Protocol for Underwater Wireless Sensor Networks (UWSNs).

    Science.gov (United States)

    Wadud, Zahid; Ullah, Khadem; Hussain, Sajjad; Yang, Xiaodong; Qazi, Abdul Baseer

    2018-05-12

    Underwater Wireless Sensor Networks (UWSNs) have intrinsic challenges that include long propagation delays, high mobility of sensor nodes due to water currents, Doppler spread, delay variance, multipath, attenuation and geometric spreading. The existing Weighting Depth and Forwarding Area Division Depth Based Routing (WDFAD-DBR) protocol considers the weighting depth of the two hops in order to select the next Potential Forwarding Node (PFN). To improve the performance of WDFAD-DBR, we propose DOlphin and Whale Pod Routing protocol (DOW-PR). In this scheme, we divide the transmission range into a number of transmission power levels and at the same time select the next PFNs from forwarding and suppressed zones. In contrast to WDFAD-DBR, our scheme not only considers the packet upward advancement, but also takes into account the number of suppressed nodes and number of PFNs at the first and second hops. Consequently, reasonable energy reduction is observed while receiving and transmitting packets. Moreover, our scheme also considers the hops count of the PFNs from the sink. In the absence of PFNs, the proposed scheme will select the node from the suppressed region for broadcasting and thus ensures minimum loss of data. Besides this, we also propose another routing scheme (whale pod) in which multiple sinks are placed at water surface, but one sink is embedded inside the water and is physically connected with the surface sink through high bandwidth connection. Simulation results show that the proposed scheme has high Packet Delivery Ratio (PDR), low energy tax, reduced Accumulated Propagation Distance (APD) and increased the network lifetime.

  18. LOTIR: A Routing Protocol for Multi-hop V-to-I Communication Using Local Traffic Information

    Directory of Open Access Journals (Sweden)

    Kun-chan Lan

    2012-08-01

    Full Text Available Vehicular Ad Hoc Network (VANET is an emerging technology that can be applied to safety, transport efficiency, or infotainment applications for roads and highways. However, due to its unique features, such as dynamic mobility patterns and uneven distributions of vehicles, VANET faces many challenging research issues for robust data dissemination in the network. Many routing protocols have been proposed for VANET in the past few years, and the idea of utilizing a navigation system to assist the routing protocol for selecting the next best forwarder has become increasingly popular. However, it might not be realistic to assume that every vehicle is equipped with a navigation system. In addition, due to privacy concerns, drivers might not want to reveal their planned routes to other cars. In this work, we propose a new routing protocol, called LOTIR (LOcal Traffic Information Routing, that relies on only local traffic information and does not require the assistance of a navigation system. LOTIR is a DTN-based routing protocol that utilizes the car-following theory and traffic light information to decide the next carrier to forward the data to. We implement LOTIR in NS-2, and our results show that it can achieve similar performance as prior work which depends on the availability of global network topology information.

  19. Interface Assignment-Based AODV Routing Protocol to Improve Reliability in Multi-Interface Multichannel Wireless Mesh Networks

    Directory of Open Access Journals (Sweden)

    Won-Suk Kim

    2015-01-01

    Full Text Available The utilization of wireless mesh networks (WMNs has greatly increased, and the multi-interface multichannel (MIMC technic has been widely used for the backbone network. Unfortunately, the ad hoc on-demand distance vector (AODV routing protocol defined in the IEEE 802.11s standard was designed for WMNs using the single-interface single-channel technic. So, we define a problem that happens when the legacy AODV is used in MIMC WMNs and propose an interface assignment-based AODV (IA-AODV in order to resolve that problem. IA-AODV, which is based on multitarget path request, consists of the PREQ prediction scheme, the PREQ loss recovery scheme, and the PREQ sender assignment scheme. A detailed operation according to various network conditions and services is introduced, and the routing efficiency and network reliability of a network using IA-AODV are analyzed over the presented system model. Finally, after a real-world test-bed for MIMC WMNs using the IA-AODV routing protocol is implemented, the various indicators of the network are evaluated through experiments. When the proposed routing protocol is compared with the existing AODV routing protocol, it performs the path update using only 14.33% of the management frames, completely removes the routing malfunction, and reduces the UDP packet loss ratio by 0.0012%.

  20. Enhancement of Adaptive Cluster Hierarchical Routing Protocol using Distance and Energy for Wireless Sensor Networks

    International Nuclear Information System (INIS)

    Nawar, N.M.; Soliman, S.E.; Kelash, H.M.; Ayad, N.M.

    2014-01-01

    The application of wireless networking is widely used in nuclear applications. This includes reactor control and fire dedication system. This paper is devoted to the application of this concept in the intrusion system of the Radioisotope Production Facility (RPF) of the Egyptian Atomic Energy Authority. This includes the tracking, monitoring and control components of this system. The design and implementation of wireless sensor networks has become a hot area of research due to the extensive use of sensor networks to enable applications that connect the physical world to the virtual world [1-2]. The original LEACH is named a communication protocol (clustering-based); the extended LEACH’s stochastic cluster head selection algorithm by a deterministic component. Depending on the network configuration an increase of network lifetime can be accomplished [3]. The proposed routing mechanisms after enhancement divide the nodes into clusters. A cluster head performs its task which is considerably more energy-intensive than the rest of the nodes inside sensor network. So, nodes rotate tasks at different rounds between a cluster head and other sensors throughout the lifetime of the network to balance the energy dissipation [4-5].The performance improvement when using routing protocol after enhancement of the algorithm which takes into consideration the distance and the remaining energy for choosing the cluster head by obtains from the advertise message. Network Simulator (Ns2 simulator) is used to prove that LEACH after enhancement performs better than the original LEACH protocol in terms of Average Energy, Network Life Time, Delay, Throughput and Overhead.

  1. Performance of Implementation IBR-DTN and Batman-Adv Routing Protocol in Wireless Mesh Networks

    Directory of Open Access Journals (Sweden)

    Herman Yuliandoko

    2016-03-01

    Full Text Available Wireless mesh networks is a network which has high mobility and flexibility network. In Wireless mesh networks nodes are free to move and able to automatically build a network connection with other nodes. High mobility, heterogeneous condition and intermittent network connectivity cause data packets drop during wireless communication and it becomes a problem in the wireless mesh networks. This condition can happen because wireless mesh networks use connectionless networking type such as IP protocol which it is not tolerant to delay. To solve this condition it is needed a technology to keep data packets when the network is disconnect. Delay tolerant technology is a technology that provides store and forward mechanism and it can prevent packet data dropping during communication. In our research, we proposed a test bed wireless mesh networks implementation by using proactive routing protocol and combining with delay tolerant technology. We used Batman-adv routing protocol and IBR-DTN on our research. We measured some particular performance aspect of networking such as packet loss, delay, and throughput of the network. We identified that delay tolerant could keep packet data from dropping better than current wireless mesh networks in the intermittent network condition. We also proved that IBR-DTN and Batman-adv could run together on the wireless mesh networks. In The experiment throughput test result of IBR-DTN was higher than Current TCP on the LoS (Line of Side and on environment with obstacle. Keywords: Delay Tolerant, IBR-DTN, Wireless Mesh, Batman-adv, Performance

  2. Self-Adaptive Context Aware Routing Protocol for Unicast Communication in Delay and Tolerant Network

    Directory of Open Access Journals (Sweden)

    Yunbo Chen

    2014-05-01

    Full Text Available At present, most of research works in mobile network focus on the network overhead of the known path which exists between the sender and the receiver. However, the trend of the current practical application demands is becoming increasingly distributed and decentralized. The Delay and Tolerant Network (DTN just comes out of such background of the conflicts between them. The DTN could effectively eliminate the gap between the mobile network and the practical application demands. In this paper, a Self-Adaptive Context Aware Routing Protocol (SACARP for the unicast communication in delay and tolerant networks is presented. Meanwhile, according to the real-time context information of DTN, the Kalman filter theory is introduced to predict the information state of mobility for the optional message ferrying node, and then gives the optimal selection strategy of the message ferrying nodes. The simulation experiments have shown that, compared to the familiar single- copy and multi-copy protocols, the SACARP proposed in this paper has better transmission performance and stability, especially when the network is free, the protocol would keep a good performance with fewer connections and less buffer space.

  3. Stateless multicast switching in software defined networks

    OpenAIRE

    Reed, Martin J.; Al-Naday, Mays; Thomos, Nikolaos; Trossen, Dirk; Petropoulos, George; Spirou, Spiros

    2016-01-01

    Multicast data delivery can significantly reduce traffic in operators' networks, but has been limited in deployment due to concerns such as the scalability of state management. This paper shows how multicast can be implemented in contemporary software defined networking (SDN) switches, with less state than existing unicast switching strategies, by utilising a Bloom Filter (BF) based switching technique. Furthermore, the proposed mechanism uses only proactive rule insertion, and thus, is not l...

  4. Evaluating multicast resilience in carrier ethernet

    DEFF Research Database (Denmark)

    Ruepp, Sarah Renée; Wessing, Henrik; Zhang, Jiang

    2010-01-01

    This paper gives an overview of the Carrier Ethernet technology with specific focus on resilience. In particular, we show how multicast traffic, which is essential for IPTV can be protected. We detail the ackground for resilience mechanisms and their control and e present Carrier Ethernet...... resilience methods for linear nd ring networks. By simulation we show that the vailability of a multicast connection can be significantly increased by applying protection methods....

  5. Optimal multicasting in a multi-line-rate ethernet-over-WDM network

    Science.gov (United States)

    Harve, Shruthi; Batayneh, Marwan; Mukherjee, Biswanath

    2009-11-01

    Ethernet is the dominant transport technology for Local Area Networks. Efforts are now under way to use carrier-grade Ethernet in backbone networks of different service providers. With the advent of applications such as IPTV and Videoon- Demand, there is need for techniques to route multicast traffic over the Ethernet backbone networks. Here, we address the problem of Routing and Wavelength Assignment (RWA) of a set of multicast requests in a Multi-Line-Rate Ethernet backbone network with the objective of minimizing the cost of setting up the network, in terms of the Service Provider's Capital Expenditure (CAPEX). We present an Auxiliary Graph based heuristic algorithm that routes each multicast request on a light-tree structure, and assigns minimum cost wavelengths along the route. We compare the properties of the algorithm to the optimal solution given by a mathematical model formulated as an Integer Linear Program (ILP), and show that they compare very well. We also find that the algorithm is most cost-effective when the incoming requests are processed in descending order of their bandwidth requirements.

  6. Design and Analysis of QoS Routing Framework integrated with OLSR protocol for Multimedia Traffic in Mobile Adhoc Networks

    Directory of Open Access Journals (Sweden)

    S. Soni

    2017-06-01

    Full Text Available MANETs (Mobile Ad-hoc Networks is the self organizing wireless structure of mobile hosts. Wireless media is used for communication in MANETs. Considering the developing requirements for multimedia and real-time traffic applications in real world, QoS (Quality-of-Service support is essential in MANETs. But most of the characteristics of MANETs make QoS support a difficult problem. It is challenging to support QoS routing in MANET due to dynamic behavior and mobility of the hosts. The OLSR (Optimized Link State Routing protocol can be efficiently used in MANETs to provide QoS routing because of its dynamic MPR (Multi Point Relay selection criteria and proactive nature. In this paper, a design of QoS routing framework integrated with OLSR protocol is proposed and also analyzed using network simulator. Proposed QoS framework combines a bandwidth estimation algorithm with explicit resource reservation, QoS routing and connection admission control (CAC. OLSR protocol is extended for QoS framework to solve performance issues related to node mobility using cross layer approach. Results after simulation conclude about efficiency of the proposed QoS routing framework.

  7. Optimising social information by game theory and ant colony method to enhance routing protocol in opportunistic networks

    Directory of Open Access Journals (Sweden)

    Chander Prabha

    2016-09-01

    Full Text Available The data loss and disconnection of nodes are frequent in the opportunistic networks. The social information plays an important role in reducing the data loss because it depends on the connectivity of nodes. The appropriate selection of next hop based on social information is critical for improving the performance of routing in opportunistic networks. The frequent disconnection problem is overcome by optimising the social information with Ant Colony Optimization method which depends on the topology of opportunistic network. The proposed protocol is examined thoroughly via analysis and simulation in order to assess their performance in comparison with other social based routing protocols in opportunistic network under various parameters settings.

  8. IPTV multicast with peer-assisted lossy error control

    Science.gov (United States)

    Li, Zhi; Zhu, Xiaoqing; Begen, Ali C.; Girod, Bernd

    2010-07-01

    Emerging IPTV technology uses source-specific IP multicast to deliver television programs to end-users. To provide reliable IPTV services over the error-prone DSL access networks, a combination of multicast forward error correction (FEC) and unicast retransmissions is employed to mitigate the impulse noises in DSL links. In existing systems, the retransmission function is provided by the Retransmission Servers sitting at the edge of the core network. In this work, we propose an alternative distributed solution where the burden of packet loss repair is partially shifted to the peer IP set-top boxes. Through Peer-Assisted Repair (PAR) protocol, we demonstrate how the packet repairs can be delivered in a timely, reliable and decentralized manner using the combination of server-peer coordination and redundancy of repairs. We also show that this distributed protocol can be seamlessly integrated with an application-layer source-aware error protection mechanism called forward and retransmitted Systematic Lossy Error Protection (SLEP/SLEPr). Simulations show that this joint PARSLEP/ SLEPr framework not only effectively mitigates the bottleneck experienced by the Retransmission Servers, thus greatly enhancing the scalability of the system, but also efficiently improves the resistance to the impulse noise.

  9. Multicast Performance Analysis for High-Speed Torus Networks

    National Research Council Canada - National Science Library

    Oral, S; George, A

    2002-01-01

    ... for unicast-based and path-based multicast communication on high-speed torus networks. Software-based multicast performance results of selected algorithms on a 16-node Scalable Coherent Interface (SCI) torus are given...

  10. Merging Network Coding with Feedback Management in Multicast Streaming

    DEFF Research Database (Denmark)

    Moreira, André; Almeida, Luis; Roetter, Daniel Enrique Lucani

    2015-01-01

    Reliable multicast over wireless poses interesting challenges arising from the unreliable nature of the wireless medium. Recovering lost packets is particularly challenging in multicast scenarios since different receivers lose different packets. For this reason, simply retransmitting packets does...

  11. Probabilistic Location-based Routing Protocol for Mobile Wireless Sensor Networks with Intermittent Communication

    Directory of Open Access Journals (Sweden)

    Sho KUMAGAI

    2015-02-01

    Full Text Available In a sensor network, sensor data messages reach the nearest stationary sink node connected to the Internet by wireless multihop transmissions. Recently, various mobile sensors are available due to advances of robotics technologies and communication technologies. A location based message-by-message routing protocol, such as Geographic Distance Routing (GEDIR is suitable for such mobile wireless networks; however, it is required for each mobile wireless sensor node to know the current locations of all its neighbor nodes. On the other hand, various intermittent communication methods for a low power consumption requirement have been proposed for wireless sensor networks. Intermittent Receiver-driven Data Transmission (IRDT is one of the most efficient methods; however, it is difficult to combine the location based routing and the intermittent communication. In order to solve this problem, this paper proposes a probabilistic approach IRDT-GEDIR with the help of one of the solutions of the secretaries problem. Here, each time a neighbor sensor node wakes up from its sleep mode, an intermediate sensor node determines whether it forwards its buffered sensor data messages to it or not based on an estimation of achieved pseudo speed of the messages. Simulation experiments show that IRDT-GEDIR achieves higher pseudo speed of sensor data message transmissions and shorter transmission delay than achieves shorter transmission delay than the two naive combinations of IRDT and GEDIR in sensor networks with mobile sensor nodes and a stationary sink node. In addition, the guideline of the estimated numbers of the neighbor nodes of each intermediate sensor node is provided based on the results of the simulation experiments to apply the probabilistic approach IRDT-GEDIR.

  12. GeoVanet: A Routing Protocol for Query Processing in Vehicular Networks

    Directory of Open Access Journals (Sweden)

    Thierry Delot

    2011-01-01

    Full Text Available In a vehicular ad hoc network (VANET, cars can exchange information by using short-range wireless communications. Along with the opportunities offered by vehicular networks, a number of challenges also arise. In particular, most works so far have focused on a push model, where potentially useful data are pushed towards vehicles. The use of pull models, that would allow users to send queries to a set of cars in order to find the desired information, has not been studied in depth. The main challenge for pull models is the difficulty to route the different results towards the query originator in a highly dynamic network where the nodes move very quickly. To solve this issue, we propose GeoVanet, an anonymous and non-intrusive geographic routing protocol which ensures that the sender of a query can get a consistent answer. Our goal is to ensure that the user will be able to retrieve the query results within a bounded time. To prove the effectiveness of GeoVanet, an extensive experimental evaluation has been performed, that proves the interest of the proposal for both rural and urban areas. It shows that up to 80% of the available query results are delivered to the user.

  13. An Energy Centric Cluster-Based Routing Protocol for Wireless Sensor Networks.

    Science.gov (United States)

    Hosen, A S M Sanwar; Cho, Gi Hwan

    2018-05-11

    Clustering is an effective way to prolong the lifetime of a wireless sensor network (WSN). The common approach is to elect cluster heads to take routing and controlling duty, and to periodically rotate each cluster head's role to distribute energy consumption among nodes. However, a significant amount of energy dissipates due to control messages overhead, which results in a shorter network lifetime. This paper proposes an energy-centric cluster-based routing mechanism in WSNs. To begin with, cluster heads are elected based on the higher ranks of the nodes. The rank is defined by residual energy and average distance from the member nodes. With the role of data aggregation and data forwarding, a cluster head acts as a caretaker for cluster-head election in the next round, where the ranks' information are piggybacked along with the local data sending during intra-cluster communication. This reduces the number of control messages for the cluster-head election as well as the cluster formation in detail. Simulation results show that our proposed protocol saves the energy consumption among nodes and achieves a significant improvement in the network lifetime.

  14. A Survey of Routing Issues and Associated Protocols in Underwater Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Muhammad Khalid

    2017-01-01

    Full Text Available Underwater wireless sensor networks are a newly emerging wireless technology in which small size sensors with limited energy and limited memory and bandwidth are deployed in deep sea water and various monitoring operations like tactical surveillance, environmental monitoring, and data collection are performed through these tiny sensors. Underwater wireless sensor networks are used for the exploration of underwater resources, oceanographic data collection, flood or disaster prevention, tactical surveillance systems, and unmanned underwater vehicles. Sensor nodes consist of a small memory, a central processing unit, and an antenna. Underwater networks are much different from terrestrial sensor networks as radio waves cannot be used in underwater wireless sensor networks. Acoustic channels are used for communication in deep sea water. Acoustic signals have many limitations, such as limited bandwidth, higher end-to-end delay, network path loss, higher propagation delay, and dynamic topology. Usually, these limitations result in higher energy consumption with a smaller number of packets delivered. The main aim nowadays is to operate sensor nodes having a smaller battery for a longer time in the network. This survey has discussed the state-of-the-art localization based and localization-free routing protocols. Routing associated issues in the area of underwater wireless sensor networks have also been discussed.

  15. Pithy Review on Routing Protocols in Wireless Sensor Networks and Least Routing Time Opportunistic Technique in WSN

    Science.gov (United States)

    Salman Arafath, Mohammed; Rahman Khan, Khaleel Ur; Sunitha, K. V. N.

    2018-01-01

    Nowadays due to most of the telecommunication standard development organizations focusing on using device-to-device communication so that they can provide proximity-based services and add-on services on top of the available cellular infrastructure. An Oppnets and wireless sensor network play a prominent role here. Routing in these networks plays a significant role in fields such as traffic management, packet delivery etc. Routing is a prodigious research area with diverse unresolved issues. This paper firstly focuses on the importance of Opportunistic routing and its concept then focus is shifted to prime aspect i.e. on packet reception ratio which is one of the highest QoS Awareness parameters. This paper discusses the two important functions of routing in wireless sensor networks (WSN) namely route selection using least routing time algorithm (LRTA) and data forwarding using clustering technique. Finally, the simulation result reveals that LRTA performs relatively better than the existing system in terms of average packet reception ratio and connectivity.

  16. A Dynamic Active Multicast Group Access Control Framework Based on Trust Management System

    Institute of Scientific and Technical Information of China (English)

    YANG Chang; CHEN Xiaolin; ZHANG Huanguo

    2006-01-01

    The current multicast model provides no access control mechanism. Any host can send data directly to a multicast address or join a multicast group to become a member, which brings safety problems to multicast. In this paper, we present a new active multicast group access control mechanism that is founded on trust management. This structure can solve the problem that exists in multicast members' access control and distributing authorization of traditional IP multicast.

  17. Exploiting the In-Network Capabilities of Multicast to Discover Proximate IPTV Channels

    Directory of Open Access Journals (Sweden)

    William Donnelly

    2010-09-01

    Full Text Available IPTV has become the next generation of television due, in part, to its ability to support features that have been lacking in conventional broadcasting—for example, end-user interactivity, personalisation and localisation. Providers are also searching for the most efficient delivery methods to provide the greatest amount of contents at the lowest cost. At present IPTV uses IP multicast to deliver live TV channels in an over-provisioned walled-garden network due to issues of deploying multicast and QoS challenges in the public Internet. However, IPTV is likely to shift into some parts of the public Internet in the future as a managed service. Multicast routing is performed on a per-session destination-address basis so each router maintains a table of all of the multicast addresses to which the content is being forwarded. We exploit this information to discover and join the in-progress channels of geographically proximate users and to create a new incentivised premium service in future IPTV networks called ProxyTV. This approach is expected to minimise network bandwidth requirements as it enables ISPs to optimise bandwidth on their edge networks. This becomes increasingly significant as TV content consumes more and more bandwidth, especially with the onset of HD and 3D capabilities. In this paper, we have presented in detail the concept with the results of a survey and an analysis of network traffic to justify the proposed approach.

  18. Multihopping Multilevel Clustering Heterogeneity-Sensitive Optimized Routing Protocol for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Muhammad Aslam

    2017-01-01

    Full Text Available Effective utilization of energy resources in Wireless Sensor Networks (WSNs has become challenging under uncertain distributed cluster-formation and single-hop intercluster communication capabilities. So, sensor nodes are forced to operate at expensive full rate transmission power level continuously during whole network operation. These challenging network environments experience unwanted phenomena of drastic energy consumption and packet drop. In this paper, we propose an adaptive immune Multihopping Multilevel Clustering (MHMLC protocol that executes a Hybrid Clustering Algorithm (HCA to perform optimal centralized selection of Cluster-Heads (CHs within radius of centrally located Base Station (BS and distributed CHs selection in the rest of network area. HCA of MHMLC also produces optimal intermediate CHs for intercluster multihop communications that develop heterogeneity-aware economical links. This hybrid cluster-formation facilitates the sensors to function at short range transmission power level that enhances link quality and avoids packet drop. The simulation environments produce fair comparison among proposed MHMLC and existing state-of-the-art routing protocols. Experimental results give significant evidence of better performance of the proposed model in terms of network lifetime, stability period, and data delivery ratio.

  19. Effect of variation in active route timeout and my route timeout on the performance of AODV-ETX protocol in mobile adhoc network

    Science.gov (United States)

    Purnomo, A.; Widyawan; Najib, W.; Hartono, R.; Hartatik

    2018-03-01

    Mobile adhoc network (MANET) consists of nodes that are independent. A node can communicate each other without the presence of network infrastructure. A node can act as a transmitter and receiver as well as a router. This research has been variation in active route timeout and my route timeout on the performance of AODV-ETX protocol in MANET. The AODV-ETX protocol is the AODV protocol that uses the ETX metric. Performance testing is done on the static node topology with 5 m x 5 m node grid model where the distance between nodes is 100 m and node topology that consists of 25 nodes moves randomly with a moving speed of 1.38 m/s in an area of 1500 m x 300 m. From the test result, on the static node, AODV protocol-ETX shows optimal performance at a value MRT and ART of 10 s and 15 s, but showed a stable performance in the value of MRT and ART ≥60 s, while in randomly moved node topology shows stable performance in the value of MRT and ART ≥80 s.

  20. A General Self-Organized Tree-Based Energy-Balance Routing Protocol for Wireless Sensor Network

    Science.gov (United States)

    Han, Zhao; Wu, Jie; Zhang, Jie; Liu, Liefeng; Tian, Kaiyun

    2014-04-01

    Wireless sensor network (WSN) is a system composed of a large number of low-cost micro-sensors. This network is used to collect and send various kinds of messages to a base station (BS). WSN consists of low-cost nodes with limited battery power, and the battery replacement is not easy for WSN with thousands of physically embedded nodes, which means energy efficient routing protocol should be employed to offer a long-life work time. To achieve the aim, we need not only to minimize total energy consumption but also to balance WSN load. Researchers have proposed many protocols such as LEACH, HEED, PEGASIS, TBC and PEDAP. In this paper, we propose a General Self-Organized Tree-Based Energy-Balance routing protocol (GSTEB) which builds a routing tree using a process where, for each round, BS assigns a root node and broadcasts this selection to all sensor nodes. Subsequently, each node selects its parent by considering only itself and its neighbors' information, thus making GSTEB a dynamic protocol. Simulation results show that GSTEB has a better performance than other protocols in balancing energy consumption, thus prolonging the lifetime of WSN.

  1. On using multiple routing metrics with destination sequenced distance vector protocol for MultiHop wireless ad hoc networks

    Science.gov (United States)

    Mehic, M.; Fazio, P.; Voznak, M.; Partila, P.; Komosny, D.; Tovarek, J.; Chmelikova, Z.

    2016-05-01

    A mobile ad hoc network is a collection of mobile nodes which communicate without a fixed backbone or centralized infrastructure. Due to the frequent mobility of nodes, routes connecting two distant nodes may change. Therefore, it is not possible to establish a priori fixed paths for message delivery through the network. Because of its importance, routing is the most studied problem in mobile ad hoc networks. In addition, if the Quality of Service (QoS) is demanded, one must guarantee the QoS not only over a single hop but over an entire wireless multi-hop path which may not be a trivial task. In turns, this requires the propagation of QoS information within the network. The key to the support of QoS reporting is QoS routing, which provides path QoS information at each source. To support QoS for real-time traffic one needs to know not only minimum delay on the path to the destination but also the bandwidth available on it. Therefore, throughput, end-to-end delay, and routing overhead are traditional performance metrics used to evaluate the performance of routing protocol. To obtain additional information about the link, most of quality-link metrics are based on calculation of the lost probabilities of links by broadcasting probe packets. In this paper, we address the problem of including multiple routing metrics in existing routing packets that are broadcasted through the network. We evaluate the efficiency of such approach with modified version of DSDV routing protocols in ns-3 simulator.

  2. The Impact of Packet Loss Behavior in 802.11g on the Cooperation Gain in Reliable Multicast

    DEFF Research Database (Denmark)

    Heide, Janus; Vingelmann, Peter; Pedersen, Morten Videbæk

    2012-01-01

    In group-oriented applications for wireless networks, reliable multicast strategies are important in order to efficiently distribute data, e.g. in Wireless Mesh Networks (WMNs) and Mobile Ad-hoc NETworks (MANETs). To ensure that developed protocols and systems will operate as expected when deploy...

  3. A Localization Based Cooperative Routing Protocol for Underwater Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Nadeem Javaid

    2017-01-01

    Full Text Available Localization is one of the major aspects in underwater wireless sensor networks (UWSNs. Therefore, it is important to know the accurate position of the sensor node in large scale applications like disaster prevention, tactical surveillance, and monitoring. Due to the inefficiency of the global positioning system (GPS in UWSN, it is very difficult to localize a node in underwater environment compared to terrestrial networks. To minimize the localization error and enhance the localization coverage of the network, two routing protocols are proposed; the first one is mobile autonomous underwater vehicle (MobiL-AUV and the second one is cooperative MobiL (CO-MobiL. In MobiL-AUV, AUVs are deployed and equipped with GPS and act as reference nodes. These reference nodes are used to localize all the nonlocalized ordinary sensor nodes in order to reduce the localization error and maximize the network coverage. CO-MobiL is presented in order to improve the network throughput by using the maximal ratio combining (MRC as diversity technique which combines both signals, received from the source and received from the relay at the destination. It uses amplify-and-forward (AF mechanism to improve the signal between the source and the destination. To support our claims, extensive simulations are performed.

  4. A Scalable Context-Aware Objective Function (SCAOF of Routing Protocol for Agricultural Low-Power and Lossy Networks (RPAL

    Directory of Open Access Journals (Sweden)

    Yibo Chen

    2015-08-01

    Full Text Available In recent years, IoT (Internet of Things technologies have seen great advances, particularly, the IPv6 Routing Protocol for Low-power and Lossy Networks (RPL, which provides a powerful and flexible routing framework that can be applied in a variety of application scenarios. In this context, as an important role of IoT, Wireless Sensor Networks (WSNs can utilize RPL to design efficient routing protocols for a specific application to increase the ubiquity of networks with resource-constrained WSN nodes that are low-cost and easy to deploy. In this article, our work starts with the description of Agricultural Low-power and Lossy Networks (A-LLNs complying with the LLN framework, and to clarify the requirements of this application-oriented routing solution. After a brief review of existing optimization techniques for RPL, our contribution is dedicated to a Scalable Context-Aware Objective Function (SCAOF that can adapt RPL to the environmental monitoring of A-LLNs, through combining energy-aware, reliability-aware, robustness-aware and resource-aware contexts according to the composite routing metrics approach. The correct behavior of this enhanced RPL version (RPAL was verified by performance evaluations on both simulation and field tests. The obtained experimental results confirm that SCAOF can deliver the desired advantages on network lifetime extension, and high reliability and efficiency in different simulation scenarios and hardware testbeds.

  5. A Scalable Context-Aware Objective Function (SCAOF) of Routing Protocol for Agricultural Low-Power and Lossy Networks (RPAL).

    Science.gov (United States)

    Chen, Yibo; Chanet, Jean-Pierre; Hou, Kun-Mean; Shi, Hongling; de Sousa, Gil

    2015-08-10

    In recent years, IoT (Internet of Things) technologies have seen great advances, particularly, the IPv6 Routing Protocol for Low-power and Lossy Networks (RPL), which provides a powerful and flexible routing framework that can be applied in a variety of application scenarios. In this context, as an important role of IoT, Wireless Sensor Networks (WSNs) can utilize RPL to design efficient routing protocols for a specific application to increase the ubiquity of networks with resource-constrained WSN nodes that are low-cost and easy to deploy. In this article, our work starts with the description of Agricultural Low-power and Lossy Networks (A-LLNs) complying with the LLN framework, and to clarify the requirements of this application-oriented routing solution. After a brief review of existing optimization techniques for RPL, our contribution is dedicated to a Scalable Context-Aware Objective Function (SCAOF) that can adapt RPL to the environmental monitoring of A-LLNs, through combining energy-aware, reliability-aware, robustness-aware and resource-aware contexts according to the composite routing metrics approach. The correct behavior of this enhanced RPL version (RPAL) was verified by performance evaluations on both simulation and field tests. The obtained experimental results confirm that SCAOF can deliver the desired advantages on network lifetime extension, and high reliability and efficiency in different simulation scenarios and hardware testbeds.

  6. Comparison of MANET routing protocols using a scaled indoor wireless grid

    CSIR Research Space (South Africa)

    Johnson, DL

    2008-04-01

    Full Text Available accumulation feature of Dynamic Source Routing (DSR) by adding the accumulated route, back to the source, to the Route Request packet. It retains the destination sequence number feature of AODV but HELLO packets are an optional feature and are normally left... than the inbound traffic as the routing algorithm makes a decision to rebroadcast the packet or not and Figure 20 confirms this. DYMO shows the least amount of routing traffic due to its lack of HELLO packets. This is also due to no further...

  7. Energy-efficient multicast traffic grooming strategy based on light-tree splitting for elastic optical networks

    Science.gov (United States)

    Liu, Huanlin; Yin, Yarui; Chen, Yong

    2017-07-01

    In order to address the problem of optimizing the spectrum resources and power consumption in elastic optical networks (EONs), we investigate the potential gains by jointly employing the light-tree splitting and traffic grooming for multicast requests. An energy-efficient multicast traffic grooming strategy based on light-tree splitting (EED-MTGS-LS) is proposed in this paper. Firstly, we design a traffic pre-processing mechanism to decide the multicast requests' routing order, which considers the request's bandwidth requirement and physical hops synthetically. Then, by dividing a light-tree to some sub-light-trees and grooming the request to these sub-light-trees, the light-tree sharing ratios of multicast requests can be improved. What's more, a priority scheduling vector is constructed, which aims to improve the success rate of spectrum assignment for grooming requests. Finally, a grooming strategy is designed to optimize the total power consumption by reducing the use of transponders and IP routers during routing. Simulation results show that the proposed strategy can significantly improve the spectrum utilization and save the power consumption.

  8. AR-RBFS: Aware-Routing Protocol Based on Recursive Best-First Search Algorithm for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Farzad Kiani

    2016-01-01

    Full Text Available Energy issue is one of the most important problems in wireless sensor networks. They consist of low-power sensor nodes and a few base station nodes. They must be adaptive and efficient in data transmission to sink in various areas. This paper proposes an aware-routing protocol based on clustering and recursive search approaches. The paper focuses on the energy efficiency issue with various measures such as prolonging network lifetime along with reducing energy consumption in the sensor nodes and increasing the system reliability. Our proposed protocol consists of two phases. In the first phase (network development phase, the sensors are placed into virtual layers. The second phase (data transmission is related to routes discovery and data transferring so it is based on virtual-based Classic-RBFS algorithm in the lake of energy problem environments but, in the nonchargeable environments, all nodes in each layer can be modeled as a random graph and then begin to be managed by the duty cycle method. Additionally, the protocol uses new topology control, data aggregation, and sleep/wake-up schemas for energy saving in the network. The simulation results show that the proposed protocol is optimal in the network lifetime and packet delivery parameters according to the present protocols.

  9. Providing resilience for carrier ethernet multicast traffic

    DEFF Research Database (Denmark)

    Ruepp, Sarah Renée; Wessing, Henrik; Zhang, Jiang

    2009-01-01

    This paper presents an overview of the Carrier Ethernet technology with specific focus on resilience. In particular, we detail how multicast traffic, which is essential for e.g. IPTV can be protected. We present Carrier Ethernet resilience methods for linear and ring networks and show by simulation...

  10. MQARR-AODV: A NOVEL MULTIPATH QOS AWARE RELIABLE REVERSE ON-DEMAND DISTANCE VECTOR ROUTING PROTOCOL FOR MOBILE AD-HOC NETWORKS

    Directory of Open Access Journals (Sweden)

    K.G. Santhiya

    2012-12-01

    Full Text Available MANET (Mobile Ad-hoc Network is an infra structure less wireless ad-hoc network that does not require any basic central control. The topology of the network changes drastically due to very fast mobility of nodes. So an adaptive routing protocol is needed for routing in MANET. AODV (Ad-hoc On-demand Distance Vector routing is the effective and prominent on-demand Ad-hoc routing protocols. During route establishment phase in traditional AODV, only one route reply message will be sent in the reverse path to establish routing path. The high mobility of nodes may affect the reply messages which lead to the retransmission of route request message by the sender which in turn leads to higher communication delay, power consumption and the reduction in the ratio of packets delivered. Sending multiple route reply messages and establishing multiple paths in a single path discovery will reduce the routing overhead involved in maintaining the connection between source and destination nodes. Multipath routing can render high scalability, end-to-end throughput and provide load balancing in MANET. The new proposed novel Multipath QoS aware reliable routing protocol establishes two routes of maximum node disjoint paths and the data transfer is carried out in the two paths simultaneously. To select best paths, the new proposed protocol uses three parameters Link Eminence, MAC overhead and node residual energy. The experimental values prove that the MQARR-AODV protocol achieves high reliability, stability, low latency and outperforms AODV by the less energy consumption, overhead and delay.

  11. Compromises Between Quality of Service Metrics and Energy Consumption of Hierarchical and Flat Routing Protocols for Wireless Sensors Network

    Directory of Open Access Journals (Sweden)

    Abdelbari BEN YAGOUTA

    2016-11-01

    Full Text Available Wireless Sensor Network (WSN is wireless network composed of spatially distributed and tiny autonomous nodes, which cooperatively monitor physical or environmental conditions. Among the concerns of these networks is prolonging the lifetime by saving nodes energy. There are several protocols specially designed for WSNs based on energy conservation. However, many WSNs applications require QoS (Quality of Service criteria, such as latency, reliability and throughput. In this paper, we will compare three routing protocols for wireless sensors network LEACH (Low Energy Adaptive Clustering Hierarchy, AODV (Ad hoc on demand Distance Vector and LABILE (Link Quality-Based Lexical Routing using Castalia simulator in terms of energy consumption, throughput, reliability and latency time of packets received by sink under different conditions to determinate the best configurations that offers the most suitable compromises between energy conservation and all QoS metrics for each routing protocols. The results show that, the best configurations that offer the suitable compromises between energy conservation and all QoS metrics is a large number of deployed nodes with low packet rate for LEACH (300 nodes and 1 packet/s, a medium number of deployed nodes with low packet rate For AODV (100 nodes and 1 packet/s and a very low nodes density with low packet rate for LABILE (50 nodes and 1 packet/s.

  12. On the Performance of the Current MANET Routing Protocols for VoIP, HTTP, and FTP Applications

    Directory of Open Access Journals (Sweden)

    Waheb A. Jabbar

    2014-01-01

    Full Text Available The recent advances of ensemble mobile environment of smart devices with embedded sensors have enabled the MANET to play a key role in the smart cities as well as WSN and WMN. However, these smart devices are still limited in terms of energy, processor, and memory. Moreover, the efficient routing for reliable network connectivity at anytime, anywhere, and about everything is still a challenge in multihop wireless networks. This paper evaluates the QoS and energy efficiency of three active routing protocols: (i OLSRv2, a successor to OLSR, (ii DYMO, a successor to both DSR and AODV, and (iii MP-OLSR multipath extension to OLSRv2. In contrast to the related previous works which focused only on CBR traffic without considering the influence of specific traffic types on the performance of routing protocols, this work focused on this area from a different perspective. It evaluates the performance of three internet-based traffic types that can be used in the smart city applications: VoIP, HTTP, and FTP using different simulation models. The impact of the network density, load traffic, and nodes mobility on the considered protocols was evaluated by considering particular performance metrics for each traffic application. Based on the results, the study concludes by presenting useful recommendations for future work.

  13. Simulation of Routing Protocol with CoS/QoS Enhancements in Heterogeneous Communication Network

    National Research Council Canada - National Science Library

    Kubera, Emil; Sliwa, Joanna; Zubel, Krzysztof; Mroczko, Adrian

    2006-01-01

    The article describes the subject of QoS routing mechanism in tactical heterogeneous communication network consisting of network elements built in different technologies and connected following rules...

  14. Overview of the Meraka wireless grid test bed for evaluation of ad-hoc routing protocols

    CSIR Research Space (South Africa)

    Johnson, D

    2007-09-01

    Full Text Available to the source, to the Route Request packet. It retains the destination sequence number feature of AODV but HELLO packets are an optional feature and are normally left out by default. It also does away with the gratuitous RREP feature of AODV. Routing... spiral algorithm makes a decision to rebroadcast the packet or not and Fig. 5. confirms this. DYMO shows the least amount of routing traffic due to its lack of HELLO packets. This is also due to no further routing packets being transmitted once...

  15. Cross-Layer Optimal Rate Allocation for Heterogeneous Wireless Multicast

    Directory of Open Access Journals (Sweden)

    Amr Mohamed

    2009-01-01

    Full Text Available Heterogeneous multicast is an efficient communication scheme especially for multimedia applications running over multihop networks. The term heterogeneous refers to the phenomenon when multicast receivers in the same session require service at different rates commensurate with their capabilities. In this paper, we address the problem of resource allocation for a set of heterogeneous multicast sessions over multihop wireless networks. We propose an iterative algorithm that achieves the optimal rates for a set of heterogeneous multicast sessions such that the aggregate utility for all sessions is maximized. We present the formulation of the multicast resource allocation problem as a nonlinear optimization model and highlight the cross-layer framework that can solve this problem in a distributed ad hoc network environment with asynchronous computations. Our simulations show that the algorithm achieves optimal resource utilization, guarantees fairness among multicast sessions, provides flexibility in allocating rates over different parts of the multicast sessions, and adapts to changing conditions such as dynamic channel capacity and node mobility. Our results show that the proposed algorithm not only provides flexibility in allocating resources across multicast sessions, but also increases the aggregate system utility and improves the overall system throughput by almost 30% compared to homogeneous multicast.

  16. A Comparative Study of Novel Opportunistic Routing Protocols in Mobile Ad Hoc Networks

    OpenAIRE

    R. Poonkuzhali; M. Y. Sanavullah; M. R. Gurupriya

    2014-01-01

    Opportunistic routing is used, where the network has the features like dynamic topology changes and intermittent network connectivity. In Delay tolerant network or Disruption tolerant network opportunistic forwarding technique is widely used. The key idea of opportunistic routing is selecting forwarding nodes to forward data packets and coordination among these nodes to avoid duplicate transmissions. This paper gives the analysis of pros and cons of various opportunistic ...

  17. The Architecture of WiFi-Based WSN for AMR System and E-HWMP Routing Protocol

    Directory of Open Access Journals (Sweden)

    Li LI

    2014-02-01

    Full Text Available With the development of SoC technology in recent years, the ultra-low power WiFi System on SoC Chip has emerged. As a result, WiFi-based Wireless Sensor Networks come into use, especially used in Automatic Meter Reading. While because the nodes of Wireless Sensor Networks have limited energy supply, smaller storage capability and slower calculation ability, the current WiFi technology cannot be directly applied to WiFi-based Wireless Sensor Networks. The protocols should be upgraded and the security algorithms should be improved to meet the new requests. Firstly, this article describes the network architecture of WiFi-based WSN for AMR system and discusses the reason for using this analogous Mesh architecture. Secondly, the new Hardware architecture of WiFi-based WSN node is designed to realize the AMR system and verify the research work. The node can collect the data of power meter by WiFi and can be powered by a Lithium Battery. Thirdly, on the basis of study work of WiFi original routing protocol HWMP, a new method on improving the energy saving ability of HWMP to adapt the new features of WiFi-based WSN is proposed. And the simulation work on the new routing protocol E-HWMP has been done with NS2 and the simulation results show that the life cycle of the network has been extended to some degree.

  18. Design of controllable multicast for IPTV over EPON

    Science.gov (United States)

    Zhang, Chuanhao; Liu, Deming; Zhang, Li; Wu, Guangsheng

    2007-11-01

    The character of 1Gbps bandwidth and tree-based structure make EPON very suitable for broadcast or multicast services such as IPTV. In this paper we focus on security mechanisms that should be available to groups that specifically request it, and therefore are willing to pay the extra cost of implementing those mechanisms. We concentrate on two issues: how unauthorized multicast traffic can be prevented by means of multicast transit traffic control; how a group's susceptibility is likely to be reduced by means of multicast group access control. We have proposed a novel scheme that should be available to multicast groups that desire precautionary measures be taken to avert the threats of Invalid source and unauthorized access.

  19. SIMULATION AND ANALYSIS OF GREEDY ROUTING PROTOCOL IN VIEW OF ENERGY CONSUMPTION AND NETWORK LIFETIME IN THREE DIMENSIONAL UNDERWATER WIRELESS SENSOR NETWORK

    Directory of Open Access Journals (Sweden)

    SHEENA KOHLI

    2017-11-01

    Full Text Available Underwater Wireless Sensor Network (UWSN comprises of a number of miniature sized sensing devices deployed in the sea or ocean, connected by dint of acoustic links to each other. The sensors trap the ambient conditions and transmit the data from one end to another. For transmission of data in any medium, routing protocols play a crucial role. Moreover, being battery limited, an unavoidable parameter to be considered in operation and analysis of protocols is the network energy and the network lifetime. The paper discusses the greedy routing protocol for underwater wireless sensor networks. The simulation of this routing protocol also takes into consideration the characteristics of acoustic communication like attenuation, transmission loss, signal to noise ratio, noise, propagation delay. The results from these observations may be used to construct an accurate underwater communication model.

  20. Genetic based optimization for multicast routing algorithm for MANET

    Indian Academy of Sciences (India)

    three main principles of natural evolution: reproduction, natural selection and species .... For example, figure 3 shows a six-node network with node reachability shown by ... sion range of each node is 220 m using an Omni directional antenna.

  1. A Decentralized Fuzzy C-Means-Based Energy-Efficient Routing Protocol for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Osama Moh’d Alia

    2014-01-01

    Full Text Available Energy conservation in wireless sensor networks (WSNs is a vital consideration when designing wireless networking protocols. In this paper, we propose a Decentralized Fuzzy Clustering Protocol, named DCFP, which minimizes total network energy dissipation to promote maximum network lifetime. The process of constructing the infrastructure for a given WSN is performed only once at the beginning of the protocol at a base station, which remains unchanged throughout the network’s lifetime. In this initial construction step, a fuzzy C-means algorithm is adopted to allocate sensor nodes into their most appropriate clusters. Subsequently, the protocol runs its rounds where each round is divided into a CH-Election phase and a Data Transmission phase. In the CH-Election phase, the election of new cluster heads is done locally in each cluster where a new multicriteria objective function is proposed to enhance the quality of elected cluster heads. In the Data Transmission phase, the sensing and data transmission from each sensor node to their respective cluster head is performed and cluster heads in turn aggregate and send the sensed data to the base station. Simulation results demonstrate that the proposed protocol improves network lifetime, data delivery, and energy consumption compared to other well-known energy-efficient protocols.

  2. A decentralized fuzzy C-means-based energy-efficient routing protocol for wireless sensor networks.

    Science.gov (United States)

    Alia, Osama Moh'd

    2014-01-01

    Energy conservation in wireless sensor networks (WSNs) is a vital consideration when designing wireless networking protocols. In this paper, we propose a Decentralized Fuzzy Clustering Protocol, named DCFP, which minimizes total network energy dissipation to promote maximum network lifetime. The process of constructing the infrastructure for a given WSN is performed only once at the beginning of the protocol at a base station, which remains unchanged throughout the network's lifetime. In this initial construction step, a fuzzy C-means algorithm is adopted to allocate sensor nodes into their most appropriate clusters. Subsequently, the protocol runs its rounds where each round is divided into a CH-Election phase and a Data Transmission phase. In the CH-Election phase, the election of new cluster heads is done locally in each cluster where a new multicriteria objective function is proposed to enhance the quality of elected cluster heads. In the Data Transmission phase, the sensing and data transmission from each sensor node to their respective cluster head is performed and cluster heads in turn aggregate and send the sensed data to the base station. Simulation results demonstrate that the proposed protocol improves network lifetime, data delivery, and energy consumption compared to other well-known energy-efficient protocols.

  3. A Decentralized Fuzzy C-Means-Based Energy-Efficient Routing Protocol for Wireless Sensor Networks

    Science.gov (United States)

    2014-01-01

    Energy conservation in wireless sensor networks (WSNs) is a vital consideration when designing wireless networking protocols. In this paper, we propose a Decentralized Fuzzy Clustering Protocol, named DCFP, which minimizes total network energy dissipation to promote maximum network lifetime. The process of constructing the infrastructure for a given WSN is performed only once at the beginning of the protocol at a base station, which remains unchanged throughout the network's lifetime. In this initial construction step, a fuzzy C-means algorithm is adopted to allocate sensor nodes into their most appropriate clusters. Subsequently, the protocol runs its rounds where each round is divided into a CH-Election phase and a Data Transmission phase. In the CH-Election phase, the election of new cluster heads is done locally in each cluster where a new multicriteria objective function is proposed to enhance the quality of elected cluster heads. In the Data Transmission phase, the sensing and data transmission from each sensor node to their respective cluster head is performed and cluster heads in turn aggregate and send the sensed data to the base station. Simulation results demonstrate that the proposed protocol improves network lifetime, data delivery, and energy consumption compared to other well-known energy-efficient protocols. PMID:25162060

  4. Class network routing

    Science.gov (United States)

    Bhanot, Gyan [Princeton, NJ; Blumrich, Matthias A [Ridgefield, CT; Chen, Dong [Croton On Hudson, NY; Coteus, Paul W [Yorktown Heights, NY; Gara, Alan G [Mount Kisco, NY; Giampapa, Mark E [Irvington, NY; Heidelberger, Philip [Cortlandt Manor, NY; Steinmacher-Burow, Burkhard D [Mount Kisco, NY; Takken, Todd E [Mount Kisco, NY; Vranas, Pavlos M [Bedford Hills, NY

    2009-09-08

    Class network routing is implemented in a network such as a computer network comprising a plurality of parallel compute processors at nodes thereof. Class network routing allows a compute processor to broadcast a message to a range (one or more) of other compute processors in the computer network, such as processors in a column or a row. Normally this type of operation requires a separate message to be sent to each processor. With class network routing pursuant to the invention, a single message is sufficient, which generally reduces the total number of messages in the network as well as the latency to do a broadcast. Class network routing is also applied to dense matrix inversion algorithms on distributed memory parallel supercomputers with hardware class function (multicast) capability. This is achieved by exploiting the fact that the communication patterns of dense matrix inversion can be served by hardware class functions, which results in faster execution times.

  5. Multicast Delayed Authentication For Streaming Synchrophasor Data in the Smart Grid.

    Science.gov (United States)

    Câmara, Sérgio; Anand, Dhananjay; Pillitteri, Victoria; Carmo, Luiz

    2016-01-01

    Multicast authentication of synchrophasor data is challenging due to the design requirements of Smart Grid monitoring systems such as low security overhead, tolerance of lossy networks, time-criticality and high data rates. In this work, we propose inf -TESLA, Infinite Timed Efficient Stream Loss-tolerant Authentication, a multicast delayed authentication protocol for communication links used to stream synchrophasor data for wide area control of electric power networks. Our approach is based on the authentication protocol TESLA but is augmented to accommodate high frequency transmissions of unbounded length. inf TESLA protocol utilizes the Dual Offset Key Chains mechanism to reduce authentication delay and computational cost associated with key chain commitment. We provide a description of the mechanism using two different modes for disclosing keys and demonstrate its security against a man-in-the-middle attack attempt. We compare our approach against the TESLA protocol in a 2-day simulation scenario, showing a reduction of 15.82% and 47.29% in computational cost, sender and receiver respectively, and a cumulative reduction in the communication overhead.

  6. Experimental Evaluation of Unicast and Multicast CoAP Group Communication

    Directory of Open Access Journals (Sweden)

    Isam Ishaq

    2016-07-01

    Full Text Available The Internet of Things (IoT is expanding rapidly to new domains in which embedded devices play a key role and gradually outnumber traditionally-connected devices. These devices are often constrained in their resources and are thus unable to run standard Internet protocols. The Constrained Application Protocol (CoAP is a new alternative standard protocol that implements the same principals as the Hypertext Transfer Protocol (HTTP, but is tailored towards constrained devices. In many IoT application domains, devices need to be addressed in groups in addition to being addressable individually. Two main approaches are currently being proposed in the IoT community for CoAP-based group communication. The main difference between the two approaches lies in the underlying communication type: multicast versus unicast. In this article, we experimentally evaluate those two approaches using two wireless sensor testbeds and under different test conditions. We highlight the pros and cons of each of them and propose combining these approaches in a hybrid solution to better suit certain use case requirements. Additionally, we provide a solution for multicast-based group membership management using CoAP.

  7. An Economic Case for End System Multicast

    Science.gov (United States)

    Analoui, Morteza; Rezvani, Mohammad Hossein

    This paper presents a non-strategic model for the end-system multicast networks based on the concept of replica exchange economy. We believe that microeconomics is a good candidate to investigate the problem of selfishness of the end-users (peers) in order to maximize the aggregate throughput. In this solution concept, the decisions that a peer might make, does not affect the actions of the other peers at all. The proposed mechanism tunes the price of the service in such a way that general equilibrium holds.

  8. Intelligent Broadcasting in Mobile Ad Hoc Networks: Three Classes of Adaptive Protocols

    Directory of Open Access Journals (Sweden)

    Michael D. Colagrosso

    2006-11-01

    Full Text Available Because adaptability greatly improves the performance of a broadcast protocol, we identify three ways in which machine learning can be applied to broadcasting in a mobile ad hoc network (MANET. We chose broadcasting because it functions as a foundation of MANET communication. Unicast, multicast, and geocast protocols utilize broadcasting as a building block, providing important control and route establishment functionality. Therefore, any improvements to the process of broadcasting can be immediately realized by higher-level MANET functionality and applications. While efficient broadcast protocols have been proposed, no single broadcasting protocol works well in all possible MANET conditions. Furthermore, protocols tend to fail catastrophically in severe network environments. Our three classes of adaptive protocols are pure machine learning, intra-protocol learning, and inter-protocol learning. In the pure machine learning approach, we exhibit a new approach to the design of a broadcast protocol: the decision of whether to rebroadcast a packet is cast as a classification problem. Each mobile node (MN builds a classifier and trains it on data collected from the network environment. Using intra-protocol learning, each MN consults a simple machine model for the optimal value of one of its free parameters. Lastly, in inter-protocol learning, MNs learn to switch between different broadcasting protocols based on network conditions. For each class of learning method, we create a prototypical protocol and examine its performance in simulation.

  9. Intelligent Broadcasting in Mobile Ad Hoc Networks: Three Classes of Adaptive Protocols

    Directory of Open Access Journals (Sweden)

    Colagrosso Michael D

    2007-01-01

    Full Text Available Because adaptability greatly improves the performance of a broadcast protocol, we identify three ways in which machine learning can be applied to broadcasting in a mobile ad hoc network (MANET. We chose broadcasting because it functions as a foundation of MANET communication. Unicast, multicast, and geocast protocols utilize broadcasting as a building block, providing important control and route establishment functionality. Therefore, any improvements to the process of broadcasting can be immediately realized by higher-level MANET functionality and applications. While efficient broadcast protocols have been proposed, no single broadcasting protocol works well in all possible MANET conditions. Furthermore, protocols tend to fail catastrophically in severe network environments. Our three classes of adaptive protocols are pure machine learning, intra-protocol learning, and inter-protocol learning. In the pure machine learning approach, we exhibit a new approach to the design of a broadcast protocol: the decision of whether to rebroadcast a packet is cast as a classification problem. Each mobile node (MN builds a classifier and trains it on data collected from the network environment. Using intra-protocol learning, each MN consults a simple machine model for the optimal value of one of its free parameters. Lastly, in inter-protocol learning, MNs learn to switch between different broadcasting protocols based on network conditions. For each class of learning method, we create a prototypical protocol and examine its performance in simulation.

  10. Multicast traffic grooming in flexible optical WDM networks

    Science.gov (United States)

    Patel, Ankitkumar N.; Ji, Philip N.; Jue, Jason P.; Wang, Ting

    2012-12-01

    In Metropolitan Area Networks (MANs), point-to-multipoint applications, such as IPTV, video-on-demand, distance learning, and content distribution, can be efficiently supported through light-tree-based multicastcommunications instead of lightpath-based unicast-communications. The application of multicasting for such traffic is justified by its inherent benefits of reduced control and management overhead and elimination of redundant resource provisioning. Supporting such multicast traffic in Flexible optical WDM (FWDM) networks that can provision light-trees using optimum amount of spectrum within flexible channel spacing leads to higher wavelength and spectral efficiencies compared to the conventional ITU-T fixed grid networks. However, in spite of such flexibility, the residual channel capacity of stranded channels may not be utilized if the network does not offer channels with arbitrary line rates. Additionally, the spectrum allocated to guard bands used to isolate finer granularity channels remains unutilized. These limitations can be addressed by using traffic grooming in which low-rate multicast connections are aggregated and switched over high capacity light-trees. In this paper, we address the multicast traffic grooming problem in FWDM networks, and propose a novel auxiliary graph-based algorithm for the first time. The performance of multicast traffic grooming is evaluated in terms of spectral, cost, and energy efficiencies compared to lightpath-based transparent FWDM networks, lightpathbased traffic grooming-capable FWDM networks, multicast-enabled transparent FWDM networks, and multicast traffic grooming-capable fixed grid networks. Simulation results demonstrate that multicast traffic grooming in FWDM networks not only improves spectral efficiency, but also cost, and energy efficiencies compared to other multicast traffic provisioning approaches of FWDM and fixed grid networks.

  11. Cooperative relay-based multicasting for energy and delay minimization

    KAUST Repository

    Atat, Rachad

    2012-08-01

    Relay-based multicasting for the purpose of cooperative content distribution is studied. Optimized relay selection is performed with the objective of minimizing the energy consumption or the content distribution delay within a cluster of cooperating mobiles. Two schemes are investigated. The first consists of the BS sending the data only to the relay, and the second scheme considers the scenario of threshold-based multicasting by the BS, where a relay is selected to transmit the data to the mobiles that were not able to receive the multicast data. Both schemes show significant superiority compared to the non-cooperative scenarios, in terms of energy consumption and delay reduction. © 2012 IEEE.

  12. A Comparative Study of Wireless Sensor Networks and Their Routing Protocols

    OpenAIRE

    Subhajit Pal; Debnath Bhattacharyya; Tai-hoon Kim

    2010-01-01

    Recent developments in the area of micro-sensor devices have accelerated advances in the sensor networks field leading to many new protocols specifically designed for wireless sensor networks (WSNs). Wireless sensor networks with hundreds to thousands of sensor nodes can gather information from an unattended location and transmit the gathered data to a particular user, depending on the application. These sensor nodes have some constraints due to their limited energy, storage capacity and comp...

  13. An Improved MOEA/D for QoS Oriented Multimedia Multicasting with Network Coding

    Directory of Open Access Journals (Sweden)

    Zhaoyuan Wang

    2015-08-01

    Full Text Available Recent years witness a significant growth in multimedia applications. Among them, a stream of applications is real-time and requires one-to-many fast data transmission with stringent quality-of-service (QoS requirements, where multicast is an important supporting technology. In particular, with more and more mobile end users requesting real-time broadband multimedia applications, it is of vital importance to provide them with satisfied quality of experience. As network coding can offer higher bandwidth to users and accommodate more flows for networks than traditional routing, this paper studies the multicast routing problem with network coding and formulates it as a multi-objective optimization problem. As delay and packet loss ratio (PLR are two important performance indicators for QoS, we consider them as the two objectives for minimization. To address the problem above, we present a multi-objective evolutionary algorithm based on decomposition (MOEA/D, where an all population updating rule is devised to address the problem of lacking feasible solutions in the search space. Experimental results demonstrate the effectiveness of the proposed algorithm and it outperforms a number of state-of-the-art algorithms.

  14. An efficient mechanism for dynamic multicast traffic grooming in overlay IP/MPLS over WDM networks

    Science.gov (United States)

    Yu, Xiaojun; Xiao, Gaoxi; Cheng, Tee Hiang

    2014-08-01

    This paper proposes an efficient overlay multicast provisioning (OMP) mechanism for dynamic multicast traffic grooming in overlay IP/MPLS over WDM networks. To facilitate request provisioning, OMP jointly utilizes a data learning (DL) scheme on the IP/MPLS layer for logical link cost estimation, and a lightpath fragmentation (LPF) based method on the WDM layer for improving resource sharing in grooming process. Extensive simulations are carried out to evaluate the performance of OMP mechanism under different traffic loads, with either limited or unlimited port resources. Simulation results demonstrate that OMP significantly outperforms the existing methods. To evaluate the respective influences of the DL scheme and the LPF method on OMP performance, provisioning mechanisms only utilizing either the IP/MPLS layer DL scheme or the WDM layer LPF method are also devised. Comparison results show that both DL and LPF methods help improve OMP blocking performance, and contribution from the DL scheme is more significant when the fixed routing and first-fit wavelength assignment (RWA) strategy is adopted on the WDM layer. Effects of a few other factors, including definition of connection cost to be reported by the WDM layer to the IP/MPLS layer and WDM-layer routing method, on OMP performance are also evaluated.

  15. Fingerprint multicast in secure video streaming.

    Science.gov (United States)

    Zhao, H Vicky; Liu, K J Ray

    2006-01-01

    Digital fingerprinting is an emerging technology to protect multimedia content from illegal redistribution, where each distributed copy is labeled with unique identification information. In video streaming, huge amount of data have to be transmitted to a large number of users under stringent latency constraints, so the bandwidth-efficient distribution of uniquely fingerprinted copies is crucial. This paper investigates the secure multicast of anticollusion fingerprinted video in streaming applications and analyzes their performance. We first propose a general fingerprint multicast scheme that can be used with most spread spectrum embedding-based multimedia fingerprinting systems. To further improve the bandwidth efficiency, we explore the special structure of the fingerprint design and propose a joint fingerprint design and distribution scheme. From our simulations, the two proposed schemes can reduce the bandwidth requirement by 48% to 87%, depending on the number of users, the characteristics of video sequences, and the network and computation constraints. We also show that under the constraint that all colluders have the same probability of detection, the embedded fingerprints in the two schemes have approximately the same collusion resistance. Finally, we propose a fingerprint drift compensation scheme to improve the quality of the reconstructed sequences at the decoder's side without introducing extra communication overhead.

  16. Enhancing Network Communication in NPSNET-V Virtual Environments Using XML-Described Dynamic Behavior (DBP) Protocols

    National Research Council Canada - National Science Library

    Fischer, William

    2001-01-01

    .... Specifically, it describes design of the NPS Dynamic-Behavior-Protocol (DBP) protocols, which are multicast / unicast capable and can be added at runtime to the distributed operating environment...

  17. Error Control Techniques for Efficient Multicast Streaming in UMTS Networks: Proposals andPerformance Evaluation

    Directory of Open Access Journals (Sweden)

    Michele Rossi

    2004-06-01

    Full Text Available In this paper we introduce techniques for efficient multicast video streaming in UMTS networks where a video content has to be conveyed to multiple users in the same cell. Efficient multicast data delivery in UMTS is still an open issue. In particular, suitable solutions have to be found to cope with wireless channel errors, while maintaining both an acceptable channel utilization and a controlled delivery delay over the wireless link between the serving base station and the mobile terminals. Here, we first highlight that standard solutions such as unequal error protection (UEP of the video flow are ineffective in the UMTS systems due to its inherent large feedback delay at the link layer (Radio Link Control, RLC. Subsequently, we propose a local approach to solve errors directly at the UMTS link layer while keeping a reasonably high channel efficiency and saving, as much as possible, system resources. The solution that we propose in this paper is based on the usage of the common channel to serve all the interested users in a cell. In this way, we can save resources with respect to the case where multiple dedicated channels are allocated for every user. In addition to that, we present a hybrid ARQ (HARQ proactive protocol that, at the cost of some redundancy (added to the link layer flow, is able to consistently improve the channel efficiency with respect to the plain ARQ case, by therefore making the use of a single common channel for multicast data delivery feasible. In the last part of the paper we give some hints for future research, by envisioning the usage of the aforementioned error control protocols with suitably encoded video streams.

  18. Design alternatives for process group membership and multicast

    Science.gov (United States)

    Birman, Kenneth P.; Cooper, Robert; Gleeson, Barry

    1991-01-01

    Process groups are a natural tool for distributed programming, and are increasingly important in distributed computing environments. However, there is little agreement on the most appropriate semantics for process group membership and group communication. These issues are of special importance in the Isis system, a toolkit for distributed programming. Isis supports several styles of process group, and a collection of group communication protocols spanning a range of atomicity and ordering properties. This flexibility makes Isis adaptable to a variety of applications, but is also a source of complexity that limits performance. This paper reports on a new architecture that arose from an effort to simplify Isis process group semantics. Our findings include a refined notion of how the clients of a group should be treated, what the properties of a multicast primitive should be when systems contain large numbers of overlapping groups, and a new construct called the casuality domain. As an illustration, we apply the architecture to the problem of converting processes into fault-tolerant process groups in a manner that is 'transparent' to other processes in the system.

  19. Empirical Evaluation of Superposition Coded Multicasting for Scalable Video

    KAUST Repository

    Chun Pong Lau; Shihada, Basem; Pin-Han Ho

    2013-01-01

    In this paper we investigate cross-layer superposition coded multicast (SCM). Previous studies have proven its effectiveness in exploiting better channel capacity and service granularities via both analytical and simulation approaches. However

  20. Transmission techniques for emergent multicast and broadcast systems

    CERN Document Server

    da Silva, Mario Marques; Dinis, Rui; Souto, Nuno; Silva, Joao Carlos

    2010-01-01

    Describing efficient transmission schemes for broadband wireless systems, Transmission Techniques for Emergent Multicast and Broadcast Systems examines advances in transmission techniques and receiver designs capable of supporting the emergent wireless needs for multimedia broadcast and multicast service (MBMS) requirements. It summarizes the research and development taking place in wireless communications for multimedia MBMS and addresses the means to improved spectral efficiency to allow for increased user bit rate, as well as increased capacity of the digital cellular radio network.The text

  1. Secure Group Communications for Large Dynamic Multicast Group

    Institute of Scientific and Technical Information of China (English)

    Liu Jing; Zhou Mingtian

    2003-01-01

    As the major problem in multicast security, the group key management has been the focus of research But few results are satisfactory. In this paper, the problems of group key management and access control for large dynamic multicast group have been researched and a solution based on SubGroup Secure Controllers (SGSCs) is presented, which solves many problems in IOLUS system and WGL scheme.

  2. Using IGMP V3 for controllable multicast over EPON

    Science.gov (United States)

    Zhang, Chuanhao; Liu, Deming; Zhang, Li; Wu, Guangsheng

    2008-11-01

    The character of 1Gbps bandwidth and tree-based structure make EPON very suitable for broadcast or multicast services such as IPTV. The document proposed a novel scheme, based on the former research for controllable multicast over EPON system, mainly considering system security and maintainability. It can both control the IPTV program source's and the receiver's validity, improving the efficiency and precision. The processing of the two configurations mode is given in detail.

  3. Authenticated IGMP for Controlling Access to Multicast Distribution Tree

    Science.gov (United States)

    Park, Chang-Seop; Kang, Hyun-Sun

    A receiver access control scheme is proposed to protect the multicast distribution tree from DoS attack induced by unauthorized use of IGMP, by extending the security-related functionality of IGMP. Based on a specific network and business model adopted for commercial deployment of IP multicast applications, a key management scheme is also presented for bootstrapping the proposed access control as well as accounting and billing for CP (Content Provider), NSP (Network Service Provider), and group members.

  4. Network coding for multi-resolution multicast

    DEFF Research Database (Denmark)

    2013-01-01

    A method, apparatus and computer program product for utilizing network coding for multi-resolution multicast is presented. A network source partitions source content into a base layer and one or more refinement layers. The network source receives a respective one or more push-back messages from one...... or more network destination receivers, the push-back messages identifying the one or more refinement layers suited for each one of the one or more network destination receivers. The network source computes a network code involving the base layer and the one or more refinement layers for at least one...... of the one or more network destination receivers, and transmits the network code to the one or more network destination receivers in accordance with the push-back messages....

  5. Tunable Sparse Network Coding for Multicast Networks

    DEFF Research Database (Denmark)

    Feizi, Soheil; Roetter, Daniel Enrique Lucani; Sørensen, Chres Wiant

    2014-01-01

    This paper shows the potential and key enabling mechanisms for tunable sparse network coding, a scheme in which the density of network coded packets varies during a transmission session. At the beginning of a transmission session, sparsely coded packets are transmitted, which benefits decoding...... complexity. At the end of a transmission, when receivers have accumulated degrees of freedom, coding density is increased. We propose a family of tunable sparse network codes (TSNCs) for multicast erasure networks with a controllable trade-off between completion time performance to decoding complexity...... a mechanism to perform efficient Gaussian elimination over sparse matrices going beyond belief propagation but maintaining low decoding complexity. Supporting simulation results are provided showing the trade-off between decoding complexity and completion time....

  6. Experimental characterization of a new multicasting node architecture based on space splitters and wavelength converters

    Science.gov (United States)

    He, Hao; Su, Yikai; Hu, Peigang; Hu, Weisheng

    2005-11-01

    IPTV-based broadband services such as interactive multimedia and video conferencing are considered as promising revenue-adding services, and multicast is proven to be a good supplier to support these applications for its reduced consumption of network bandwidth. Generally there are two approaches to implement optical layer multicast. One is space-domain multicast using space-splitter which is low cost but has wavelength continuity constraint, the other is frequency-domain multicast using wavelength converter which resolves the wavelength continuity but with high costs. A new multicasting node which adopts both space-domain multicast and frequency-domain multicast is recently discussed. In this paper we present an experimental demonstration of the new multicasting node architecture based on space splitters and wavelength converters, measurements to characterize such a node are provided.

  7. Wavelength Tuning Free Transceiver Module in OLT Downstream Multicasting 4λ × 10 Gb/s TWDM-PON System

    OpenAIRE

    M. S. Salleh; A. S. M. Supa’at; S. M. Idrus; S. Yaakob; Z. M. Yusof

    2014-01-01

    We propose a new architecture of dynamic time-wavelength division multiplexing-passive optical network (TWDM-PON) system that employs integrated all-optical packet routing (AOPR) module using 4λ×10 Gbps downstream signal to support 20 km fiber transmission. This module has been designed to support high speed L2 aggregation and routing in the physical layer PON system by using multicasting cross-gain modulation (XGM) to route packet from any PON port to multiple PON links. Meanwhile, the fixed...

  8. IP over optical multicasting for large-scale video delivery

    Science.gov (United States)

    Jin, Yaohui; Hu, Weisheng; Sun, Weiqiang; Guo, Wei

    2007-11-01

    In the IPTV systems, multicasting will play a crucial role in the delivery of high-quality video services, which can significantly improve bandwidth efficiency. However, the scalability and the signal quality of current IPTV can barely compete with the existing broadcast digital TV systems since it is difficult to implement large-scale multicasting with end-to-end guaranteed quality of service (QoS) in packet-switched IP network. China 3TNet project aimed to build a high performance broadband trial network to support large-scale concurrent streaming media and interactive multimedia services. The innovative idea of 3TNet is that an automatic switched optical networks (ASON) with the capability of dynamic point-to-multipoint (P2MP) connections replaces the conventional IP multicasting network in the transport core, while the edge remains an IP multicasting network. In this paper, we will introduce the network architecture and discuss challenges in such IP over Optical multicasting for video delivery.

  9. Improvement of the Response Time in an Open Source Audioconference Architecture Based on SIP Multicast Implemented with JainSIP, JainSDP and JGAP Libraries

    Directory of Open Access Journals (Sweden)

    Carlos M. Moreno

    2014-06-01

    Full Text Available Group services like the audioconference require a minimum level of quality of service for multicast sessions. This work proposes a new overlay multicast architecture based on SIP extensions and a genetic algorithm. The architecture consists of a SIP Extender client (SE, a Multicast Gateway Agent (MGA and a Multicast Manager (MM. The SE receives information about the most adequate MGA for it determined by a genetic algorithm inside the MM, then connects the chosen MGA and maintains connection with the MM itself. The genetic algorithm is implemented with JGAP(Java Genetic Algorithm Package libraries. The SE and MGA are programmed with JainSIP and JainSDP libraries which contain Java structures associated with the SIP protocol and session description. Some experiments over UTP wired and WiFi IEEE802.11n network were performed. Partial results with static and dynamic MGA selection show that, if we compare the joining and leaving time measured inside a station containing SE client programmed with JainSIP and JainSDP libraries versus SJphone proprietary client, the software engineering may have more influence than the medium access method in the response time for a potential group member. Even more, the genetic algorithm at the MM minimizes the response time at great scale.

  10. Study of QoS control and reliable routing method for utility communication network. Application of differentiated service to the network and alternative route establishment by the IP routing protocol; Denryokuyo IP network no QoS seigyo to shinraisei kakuho no hoho. DiffServ ni yoru QoS seigyo no koka to IP ni yoru fuku root ka no kento

    Energy Technology Data Exchange (ETDEWEB)

    Oba, E.

    2000-05-01

    QoS control method which satisfies utilities communication network requirement and alternative route establishment method which is for sustaining communication during a failure are studied. Applicability of DiffServ (Differentiated Service), one of the most promising QoS control method on IP network and studying energetically in IETF WG, is studied and it is found most application used in the utility communication network except for relaying system information could he accommodated to the DiffServ network. An example of the napping of the utility communication applications to the DiffServ PHB (Per Hop Behavior) is shown in this paper. Regarding to the alternative route, usual IP routing protocol cannot establish alternative route which doesn't have common links and nodes in their paths for a destination. IP address duplication with some modification of routing protocol enables such alternative route establishment. MPLS, distance vector algorithm and link state algorithm are evaluated qualitatively, and as a result, we found MPLS is promising way to establish the route. Quantitative evaluation will be future work. (author)

  11. A Novel OBDD-Based Reliability Evaluation Algorithm for Wireless Sensor Networks on the Multicast Model

    Directory of Open Access Journals (Sweden)

    Zongshuai Yan

    2015-01-01

    Full Text Available The two-terminal reliability calculation for wireless sensor networks (WSNs is a #P-hard problem. The reliability calculation of WSNs on the multicast model provides an even worse combinatorial explosion of node states with respect to the calculation of WSNs on the unicast model; many real WSNs require the multicast model to deliver information. This research first provides a formal definition for the WSN on the multicast model. Next, a symbolic OBDD_Multicast algorithm is proposed to evaluate the reliability of WSNs on the multicast model. Furthermore, our research on OBDD_Multicast construction avoids the problem of invalid expansion, which reduces the number of subnetworks by identifying the redundant paths of two adjacent nodes and s-t unconnected paths. Experiments show that the OBDD_Multicast both reduces the complexity of the WSN reliability analysis and has a lower running time than Xing’s OBDD- (ordered binary decision diagram- based algorithm.

  12. Decentralized Cloud Method For Multicasting Media Stream

    Directory of Open Access Journals (Sweden)

    D M B N Bandara

    2015-08-01

    Full Text Available With the advancement of Information technology the concept of idea sharing has advanced. Mostly on presentations personal computer and projector have become essentials. But on most occasions for connecting these equipment cables and physical devices are used. This is inefficient and time consuming. If a problem occurs someone with technical knowledge is necessary to solve the situation. The objective of this research is to use the wireless technology to reduce the manual configuration and build up a platform where one can easily share files a visuals media and feedback. A system has been developed to detect all the devices over a network and upon granted permission will share video audio and access controls. Final outcome of the research was a collaborative software bundle which work together on a network. One part of the system is a Desktop Network Software. And other is a Mobile Application. Desktop application can detect all other devices in the network which provides the same facility and if required can allocate a group and share its screen files and have a message stream to each device using multicasting. Mobile application can act as a mobile remote to the host computer of the group which can detect any input from user and pass it to the system.

  13. Optimization of multicast optical networks with genetic algorithm

    Science.gov (United States)

    Lv, Bo; Mao, Xiangqiao; Zhang, Feng; Qin, Xi; Lu, Dan; Chen, Ming; Chen, Yong; Cao, Jihong; Jian, Shuisheng

    2007-11-01

    In this letter, aiming to obtain the best multicast performance of optical network in which the video conference information is carried by specified wavelength, we extend the solutions of matrix games with the network coding theory and devise a new method to solve the complex problems of multicast network switching. In addition, an experimental optical network has been testified with best switching strategies by employing the novel numerical solution designed with an effective way of genetic algorithm. The result shows that optimal solutions with genetic algorithm are accordance with the ones with the traditional fictitious play method.

  14. Empirical Evaluation of Superposition Coded Multicasting for Scalable Video

    KAUST Repository

    Chun Pong Lau

    2013-03-01

    In this paper we investigate cross-layer superposition coded multicast (SCM). Previous studies have proven its effectiveness in exploiting better channel capacity and service granularities via both analytical and simulation approaches. However, it has never been practically implemented using a commercial 4G system. This paper demonstrates our prototype in achieving the SCM using a standard 802.16 based testbed for scalable video transmissions. In particular, to implement the superposition coded (SPC) modulation, we take advantage a novel software approach, namely logical SPC (L-SPC), which aims to mimic the physical layer superposition coded modulation. The emulation results show improved throughput comparing with generic multicast method.

  15. Deploying Next Generation Multicast-enabled Applications Label Switched Multicast for MPLS VPNs, VPLS, and Wholesale Ethernet

    CERN Document Server

    Joseph, Vinod

    2011-01-01

    The growth, scale, and prominence of video applications over the years have placed emphasis on the most scalable and efficient way to deliver multi-play content (voice, video and data) to the end user. Multicast is the most effective and efficient carrier of video applications from a network standpoint. Financial organizations deploy large-scale multicast infrastructures to enable trading and e-commerce. The introduction of 4G and beyond makes this technology even more indispensible since mobile operators need an efficient mechanism to deliver repetitive content to many a handset, and multicas

  16. VMCast: A VM-Assisted Stability Enhancing Solution for Tree-Based Overlay Multicast.

    Directory of Open Access Journals (Sweden)

    Weidong Gu

    Full Text Available Tree-based overlay multicast is an effective group communication method for media streaming applications. However, a group member's departure causes all of its descendants to be disconnected from the multicast tree for some time, which results in poor performance. The above problem is difficult to be addressed because overlay multicast tree is intrinsically instable. In this paper, we proposed a novel stability enhancing solution, VMCast, for tree-based overlay multicast. This solution uses two types of on-demand cloud virtual machines (VMs, i.e., multicast VMs (MVMs and compensation VMs (CVMs. MVMs are used to disseminate the multicast data, whereas CVMs are used to offer streaming compensation. The used VMs in the same cloud datacenter constitute a VM cluster. Each VM cluster is responsible for a service domain (VMSD, and each group member belongs to a specific VMSD. The data source delivers the multicast data to MVMs through a reliable path, and MVMs further disseminate the data to group members along domain overlay multicast trees. The above approach structurally improves the stability of the overlay multicast tree. We further utilized CVM-based streaming compensation to enhance the stability of the data distribution in the VMSDs. VMCast can be used as an extension to existing tree-based overlay multicast solutions, to provide better services for media streaming applications. We applied VMCast to two application instances (i.e., HMTP and HCcast. The results show that it can obviously enhance the stability of the data distribution.

  17. Lossless Multicast Handovers in Proxy Fast Mobile IPv6 Networks

    NARCIS (Netherlands)

    Meijerink, Berend Jan; Heijenk, Geert

    2015-01-01

    There is a demand in the Public Protection and Disaster Relief (PPDR) community for high bandwidth services on mobile devices. Group communication is an important aspect of PPDR networks. In IP based networks multicast is the preferred method to efficiently transmit data to more than one receiver

  18. An efficient mechanism for dynamic survivable multicast traffic grooming

    Science.gov (United States)

    Yu, Xiaojun; Xiao, Gaoxi; Cheng, Tee Hiang

    2015-06-01

    Recent advances in wavelength division multiplexing (WDM) networks have helped enhance the popularity of multicasting services. However, as a single network failure may disrupt the information transmission to multiple end-users, protecting multicast requests against network failures becomes an important issue in network operation. This paper investigates the sub-wavelength level protection for dynamic multicast traffic grooming. A new method named lightpath-fragmentation based segment shared protection (LF-SSP) scheme is proposed. By carefully splitting primary/backup lightpaths into segments to improve resource sharing for both traffic grooming and protection, LF-SSP aims to minimize the network resources allocated for request protection. Extensive simulations are carried out to compare the performance of LF-SSP to some existing approaches, on sub-wavelength-level as well as wavelength-level multicast protections in different cases. Results show that LF-SSP steadily outperforms these existing methods as long as the network resources are not too limited. Influences of the add/drop port resources and the average number of destinations per connection request on the LF-SSP performance are also evaluated.

  19. Cooperative relay-based multicasting for energy and delay minimization

    KAUST Repository

    Atat, Rachad; Yaacoub, Elias E.; Alouini, Mohamed-Slim; Abu-Dayya, Adnan A.

    2012-01-01

    mobiles. Two schemes are investigated. The first consists of the BS sending the data only to the relay, and the second scheme considers the scenario of threshold-based multicasting by the BS, where a relay is selected to transmit the data to the mobiles

  20. Cooperative Optimization QoS Cloud Routing Protocol Based on Bacterial Opportunistic Foraging and Chemotaxis Perception for Mobile Internet

    Directory of Open Access Journals (Sweden)

    Shujuan Wang

    2015-01-01

    Full Text Available In order to strengthen the mobile Internet mobility management and cloud platform resources utilization, optimizing the cloud routing efficiency is established, based on opportunistic bacterial foraging bionics, and puts forward a chemotaxis perception of collaborative optimization QoS (Quality of Services cloud routing mechanism. The cloud routing mechanism is based on bacterial opportunity to feed and bacterial motility and to establish the data transmission and forwarding of the bacterial population behavior characteristics. This mechanism is based on the characteristics of drug resistance of bacteria and the structure of the field, and through many iterations of the individual behavior and population behavior the bacteria can be spread to the food gathering area with a certain probability. Finally, QoS cloud routing path would be selected and optimized based on bacterial bionic optimization and hedge mapping relationship between mobile Internet node and bacterial population evolution iterations. Experimental results show that, compared with the standard dynamic routing schemes, the proposed scheme has shorter transmission delay, lower packet error ratio, QoS cloud routing loading, and QoS cloud route request overhead.

  1. A Secure and Stable Multicast Overlay Network with Load Balancing for Scalable IPTV Services

    Directory of Open Access Journals (Sweden)

    Tsao-Ta Wei

    2012-01-01

    Full Text Available The emerging multimedia Internet application IPTV over P2P network preserves significant advantages in scalability. IPTV media content delivered in P2P networks over public Internet still preserves the issues of privacy and intellectual property rights. In this paper, we use SIP protocol to construct a secure application-layer multicast overlay network for IPTV, called SIPTVMON. SIPTVMON can secure all the IPTV media delivery paths against eavesdroppers via elliptic-curve Diffie-Hellman (ECDH key exchange on SIP signaling and AES encryption. Its load-balancing overlay tree is also optimized from peer heterogeneity and churn of peer joining and leaving to minimize both service degradation and latency. The performance results from large-scale simulations and experiments on different optimization criteria demonstrate SIPTVMON's cost effectiveness in quality of privacy protection, stability from user churn, and good perceptual quality of objective PSNR values for scalable IPTV services over Internet.

  2. A Link Quality and Geographical-aware Routing Protocol for Video Transmission in Mobile IoT

    OpenAIRE

    Rosário, Denis; Zhao, Zhongliang; Cerqueira, Eduardo; Braun, Torsten; Santos, Aldri

    2013-01-01

    Wireless mobile sensor networks are enlarging the Internet of Things (IoT) portfolio with a huge number of multimedia services for smart cities. Safety and environmental monitoring multimedia applications will be part of the Smart IoT systems, which aim to reduce emergency response time, while also predicting hazardous events. In these mobile and dynamic (possible disaster) scenarios, opportunistic routing allows routing decisions in a completely distributed manner, by using a hop- by-hop rou...

  3. Increase in Multicast OFDM Data Rate in PLC Network using Adaptive LP-OFDM

    OpenAIRE

    Maiga , Ali; Baudais , Jean-Yves; Hélard , Jean-François

    2009-01-01

    ISBN: 978-1-4244-3523-4; International audience; Linear precoding (LP) technique applied to OFDM systems has already proved its ability to significantly increase the system throughput in a powerline communication (PLC) context. In this paper, we propose resource allocation algorithms based on the LP technique to increase the multicast OFDM systems bit rate. The conventional multicast capacity is limited by the user which experiences the worst channel conditions. To increase the multicast bit ...

  4. A Multi-User Game-Theoretical Multipath Routing Protocol to Send Video-Warning Messages over Mobile Ad Hoc Networks.

    Science.gov (United States)

    Mezher, Ahmad Mohamad; Igartua, Mónica Aguilar; de la Cruz Llopis, Luis J; Pallarès Segarra, Esteve; Tripp-Barba, Carolina; Urquiza-Aguiar, Luis; Forné, Jordi; Sanvicente Gargallo, Emilio

    2015-04-17

    The prevention of accidents is one of the most important goals of ad hoc networks in smart cities. When an accident happens, dynamic sensors (e.g., citizens with smart phones or tablets, smart vehicles and buses, etc.) could shoot a video clip of the accident and send it through the ad hoc network. With a video message, the level of seriousness of the accident could be much better evaluated by the authorities (e.g., health care units, police and ambulance drivers) rather than with just a simple text message. Besides, other citizens would be rapidly aware of the incident. In this way, smart dynamic sensors could participate in reporting a situation in the city using the ad hoc network so it would be possible to have a quick reaction warning citizens and emergency units. The deployment of an efficient routing protocol to manage video-warning messages in mobile Ad hoc Networks (MANETs) has important benefits by allowing a fast warning of the incident, which potentially can save lives. To contribute with this goal, we propose a multipath routing protocol to provide video-warning messages in MANETs using a novel game-theoretical approach. As a base for our work, we start from our previous work, where a 2-players game-theoretical routing protocol was proposed to provide video-streaming services over MANETs. In this article, we further generalize the analysis made for a general number of N players in the MANET. Simulations have been carried out to show the benefits of our proposal, taking into account the mobility of the nodes and the presence of interfering traffic. Finally, we also have tested our approach in a vehicular ad hoc network as an incipient start point to develop a novel proposal specifically designed for VANETs.

  5. A Multi-User Game-Theoretical Multipath Routing Protocol to Send Video-Warning Messages over Mobile Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    Ahmad Mohamad Mezher

    2015-04-01

    Full Text Available The prevention of accidents is one of the most important goals of ad hoc networks in smart cities. When an accident happens, dynamic sensors (e.g., citizens with smart phones or tablets, smart vehicles and buses, etc. could shoot a video clip of the accident and send it through the ad hoc network. With a video message, the level of seriousness of the accident could be much better evaluated by the authorities (e.g., health care units, police and ambulance drivers rather than with just a simple text message. Besides, other citizens would be rapidly aware of the incident. In this way, smart dynamic sensors could participate in reporting a situation in the city using the ad hoc network so it would be possible to have a quick reaction warning citizens and emergency units. The deployment of an efficient routing protocol to manage video-warning messages in mobile Ad hoc Networks (MANETs has important benefits by allowing a fast warning of the incident, which potentially can save lives. To contribute with this goal, we propose a multipath routing protocol to provide video-warning messages in MANETs using a novel game-theoretical approach. As a base for our work, we start from our previous work, where a 2-players game-theoretical routing protocol was proposed to provide video-streaming services over MANETs. In this article, we further generalize the analysis made for a general number of N players in the MANET. Simulations have been carried out to show the benefits of our proposal, taking into account the mobility of the nodes and the presence of interfering traffic. Finally, we also have tested our approach in a vehicular ad hoc network as an incipient start point to develop a novel proposal specifically designed for VANETs.

  6. Performance analysis and implementation of proposed mechanism for detection and prevention of security attacks in routing protocols of vehicular ad-hoc network (VANET

    Directory of Open Access Journals (Sweden)

    Parul Tyagi

    2017-07-01

    Full Text Available Next-generation communication networks have become widely popular as ad-hoc networks, broadly categorized as the mobile nodes based on mobile ad-hoc networks (MANET and the vehicular nodes based vehicular ad-hoc networks (VANET. VANET is aimed at maintaining safety to vehicle drivers by begin autonomous communication with the nearby vehicles. Each vehicle in the ad-hoc network performs as an intelligent mobile node characterized by high mobility and formation of dynamic networks. The ad-hoc networks are decentralized dynamic networks that need efficient and secure communication requirements due to the vehicles being persistently in motion. These networks are more susceptible to various attacks like Warm Hole attacks, denial of service attacks and Black Hole Attacks. The paper is a novel attempt to examine and investigate the security features of the routing protocols in VANET, applicability of AODV (Ad hoc On Demand protocol to detect and tackle a particular category of network attacks, known as the Black Hole Attacks. A new algorithm is proposed to enhance the security mechanism of AODV protocol and to introduce a mechanism to detect Black Hole Attacks and to prevent the network from such attacks in which source node stores all route replies in a look up table. This table stores the sequences of all route reply, arranged in ascending order using PUSH and POP operations. The priority is calculated based on sequence number and discard the RREP having presumably very high destination sequence number. The result show that proposed algorithm for detection and prevention of Black Hole Attack increases security in Intelligent Transportation System (ITS and reduces the effect of malicious node in the VANET. NCTUNs simulator is used in this research work.

  7. On Designing Thermal-Aware Localized QoS Routing Protocol for in-vivo Sensor Nodes in Wireless Body Area Networks

    OpenAIRE

    Monowar, Muhammad Mostafa; Bajaber, Fuad

    2015-01-01

    In this paper, we address the thermal rise and Quality-of-Service (QoS) provisioning issue for an intra-body Wireless Body Area Network (WBAN) having in-vivo sensor nodes. We propose a thermal-aware QoS routing protocol, called TLQoS, that facilitates the system in achieving desired QoS in terms of delay and reliability for diverse traffic types, as well as avoids the formation of highly heated nodes known as hotspot(s), and keeps the temperature rise along the network to an acceptable level....

  8. Integration of look-ahead multicast and unicast scheduling for input-queued cell switches

    DEFF Research Database (Denmark)

    Yu, Hao; Ruepp, Sarah Renée; Berger, Michael Stübert

    2012-01-01

    This paper presents an integration of multicast and unicast traffic scheduling algorithms for input-queued cell switches. The multi-level round-robin multicast scheduling (ML-RRMS) algorithm with the look-ahead (LA) mechanism provides a highly scalable architecture and is able to reduce the head...... module that filters out the conflicting requests to ensure fairness. Simulation results show that comparing with the scheme using WBA for the multicast scheduling, the scheme proposed in this paper reduces the HOL blocking problem for multicast traffic and provides a significant improvement in terms...

  9. Simultaneous Wireless Power Transfer and Secure Multicasting in Cooperative Decode-and-Forward Relay Networks.

    Science.gov (United States)

    Lee, Jong-Ho; Sohn, Illsoo; Kim, Yong-Hwa

    2017-05-16

    In this paper, we investigate simultaneous wireless power transfer and secure multicasting via cooperative decode-and-forward (DF) relays in the presence of multiple energy receivers and eavesdroppers. Two scenarios are considered under a total power budget: maximizing the minimum harvested energy among the energy receivers under a multicast secrecy rate constraint; and maximizing the multicast secrecy rate under a minimum harvested energy constraint. For both scenarios, we solve the transmit power allocation and relay beamformer design problems by using semidefinite relaxation and bisection technique. We present numerical results to analyze the energy harvesting and secure multicasting performances in cooperative DF relay networks.

  10. A novel WDM passive optical network architecture supporting two independent multicast data streams

    Science.gov (United States)

    Qiu, Yang; Chan, Chun-Kit

    2012-01-01

    We propose a novel scheme to perform optical multicast overlay of two independent multicast data streams on a wavelength-division-multiplexed (WDM) passive optical network. By controlling a sinusoidal clock signal and shifting the wavelength at the optical line terminal (OLT), the delivery of the two multicast data, being carried by the generated optical tones, can be independently and flexibly controlled. Simultaneous transmission of 10-Gb/s unicast downstream and upstream data as well as two independent 10-Gb/s multicast data was successfully demonstrated.

  11. Simultaneous Wireless Power Transfer and Secure Multicasting in Cooperative Decode-and-Forward Relay Networks

    Science.gov (United States)

    Lee, Jong-Ho; Sohn, Illsoo; Kim, Yong-Hwa

    2017-01-01

    In this paper, we investigate simultaneous wireless power transfer and secure multicasting via cooperative decode-and-forward (DF) relays in the presence of multiple energy receivers and eavesdroppers. Two scenarios are considered under a total power budget: maximizing the minimum harvested energy among the energy receivers under a multicast secrecy rate constraint; and maximizing the multicast secrecy rate under a minimum harvested energy constraint. For both scenarios, we solve the transmit power allocation and relay beamformer design problems by using semidefinite relaxation and bisection technique. We present numerical results to analyze the energy harvesting and secure multicasting performances in cooperative DF relay networks. PMID:28509841

  12. Simultaneous Wireless Power Transfer and Secure Multicasting in Cooperative Decode-and-Forward Relay Networks

    Directory of Open Access Journals (Sweden)

    Jong-Ho Lee

    2017-05-01

    Full Text Available In this paper, we investigate simultaneous wireless power transfer and secure multicasting via cooperative decode-and-forward (DF relays in the presence of multiple energy receivers and eavesdroppers. Two scenarios are considered under a total power budget: maximizing the minimum harvested energy among the energy receivers under a multicast secrecy rate constraint; and maximizing the multicast secrecy rate under a minimum harvested energy constraint. For both scenarios, we solve the transmit power allocation and relay beamformer design problems by using semidefinite relaxation and bisection technique. We present numerical results to analyze the energy harvesting and secure multicasting performances in cooperative DF relay networks.

  13. Ad Hoc on-Demand Distance Vector (AODV Routing Protocol Performance Evaluation on Hybrid Ad Hoc Network: Comparison of Result of Ns-2 Simulation and Implementation on Testbed using PDA

    Directory of Open Access Journals (Sweden)

    Riri Sari

    2010-10-01

    Full Text Available In Mobile Ad hoc NETwork (MANET, node supplemented with wireless equipment has the capacity to manage and organise autonomously, without the presence of network infrastructures. Hybrid ad hoc network, enable several nodes to move freely (mobile to create instant communication. Independent from infrastructure. They could access the Local Area Network (LAN or the Internet. Functionalities of ad hoc network very much dependent on the routing protocol that determines the routing around node. Ad hoc On-demand Distance Vector (AODV is one of routing protocols in ad hoc network which has a reactive characteristic. This protocol is the most common protocol being researched and used. In this Research, AODV protocol investigation was conducted by developing a testbed using Personal Computer, several Laptops (the Linux Red Hat operation system 9.0 and Fedora Core 2, and Personal Digital Assistant (PDA. This research also made a complete package by mean of cross compilation for PDA iPAQ. In general, results obtained from the simulation of AODV protocol using Network Simulator NS-2 are packet delivery ratio 99.89%, end-to-end delay of 0.14 seconds and routing overhead of 1,756.61 byte per second. Afterwards results from simulation were compared to results from testbed. Results obtained from testbed are as follows: the packet delivery ratio is 99.57%, the end-to-end delay is 1.004 seconds and the routing overhead is 1,360.36 byte per second.

  14. Multicasting based optical inverse multiplexing in elastic optical network.

    Science.gov (United States)

    Guo, Bingli; Xu, Yingying; Zhu, Paikun; Zhong, Yucheng; Chen, Yuanxiang; Li, Juhao; Chen, Zhangyuan; He, Yongqi

    2014-06-16

    Optical multicasting based inverse multiplexing (IM) is introduced in spectrum allocation of elastic optical network to resolve the spectrum fragmentation problem, where superchannels could be split and fit into several discrete spectrum blocks in the intermediate node. We experimentally demonstrate it with a 1-to-7 optical superchannel multicasting module and selecting/coupling components. Also, simulation results show that, comparing with several emerging spectrum defragmentation solutions (e.g., spectrum conversion, split spectrum), IM could reduce blocking performance significantly but without adding too much system complexity as split spectrum. On the other hand, service fairness for traffic with different granularity of these schemes is investigated for the first time and it shows that IM performs better than spectrum conversion and almost as well as split spectrum, especially for smaller size traffic under light traffic intensity.

  15. On Designing Thermal-Aware Localized QoS Routing Protocol for in-vivo Sensor Nodes in Wireless Body Area Networks

    Directory of Open Access Journals (Sweden)

    Muhammad Mostafa Monowar

    2015-06-01

    Full Text Available In this paper, we address the thermal rise and Quality-of-Service (QoS provisioning issue for an intra-body Wireless Body Area Network (WBAN having in-vivo sensor nodes. We propose a thermal-aware QoS routing protocol, called TLQoS, that facilitates the system in achieving desired QoS in terms of delay and reliability for diverse traffic types, as well as avoids the formation of highly heated nodes known as hotspot(s, and keeps the temperature rise along the network to an acceptable level. TLQoS exploits modular architecture wherein different modules perform integrated operations in providing multiple QoS service with lower temperature rise. To address the challenges of highly dynamic wireless environment inside the human body. TLQoS implements potential-based localized routing that requires only local neighborhood information. TLQoS avoids routing loop formation as well as reduces the number of hop traversal exploiting hybrid potential, and tuning a configurable parameter. We perform extensive simulations of TLQoS, and the results show that TLQoS has significant performance improvements over state-of-the-art approaches.

  16. On Designing Thermal-Aware Localized QoS Routing Protocol for in-vivo Sensor Nodes in Wireless Body Area Networks.

    Science.gov (United States)

    Monowar, Muhammad Mostafa; Bajaber, Fuad

    2015-06-15

    In this paper, we address the thermal rise and Quality-of-Service (QoS) provisioning issue for an intra-body Wireless Body Area Network (WBAN) having in-vivo sensor nodes. We propose a thermal-aware QoS routing protocol, called TLQoS, that facilitates the system in achieving desired QoS in terms of delay and reliability for diverse traffic types, as well as avoids the formation of highly heated nodes known as hotspot(s), and keeps the temperature rise along the network to an acceptable level. TLQoS exploits modular architecture wherein different modules perform integrated operations in providing multiple QoS service with lower temperature rise. To address the challenges of highly dynamic wireless environment inside the human body. TLQoS implements potential-based localized routing that requires only local neighborhood information. TLQoS avoids routing loop formation as well as reduces the number of hop traversal exploiting hybrid potential, and tuning a configurable parameter. We perform extensive simulations of TLQoS, and the results show that TLQoS has significant performance improvements over state-of-the-art approaches.

  17. Design of an IPTV Multicast System for Internet Backbone Networks

    Directory of Open Access Journals (Sweden)

    T. H. Szymanski

    2010-01-01

    Full Text Available The design of an IPTV multicast system for the Internet backbone network is presented and explored through extensive simulations. In the proposed system, a resource reservation algorithm such as RSVP, IntServ, or DiffServ is used to reserve resources (i.e., bandwidth and buffer space in each router in an IP multicast tree. Each router uses an Input-Queued, Output-Queued, or Crosspoint-Queued switch architecture with unity speedup. A recently proposed Recursive Fair Stochastic Matrix Decomposition algorithm used to compute near-perfect transmission schedules for each IP router. The IPTV traffic is shaped at the sources using Application-Specific Token Bucker Traffic Shapers, to limit the burstiness of incoming network traffic. The IPTV traffic is shaped at the destinations using Application-Specific Playback Queues, to remove residual network jitter and reconstruct the original bursty IPTV video streams at each destination. All IPTV traffic flows are regenerated at the destinations with essentially zero delay jitter and essentially-perfect QoS. The destination nodes deliver the IPTV streams to the ultimate end users using the same IPTV multicast system over a regional Metropolitan Area Network. It is shown that all IPTV traffic is delivered with essentially-perfect end-to-end QoS, with deterministic bounds on the maximum delay and jitter on each video frame. Detailed simulations of an IPTV distribution system, multicasting several hundred high-definition IPTV video streams over several essentially saturated IP backbone networks are presented.

  18. Adaptive Modulation for a Downlink Multicast Channel in OFDMA Systems

    DEFF Research Database (Denmark)

    Wang, Haibo; Schwefel, Hans-Peter; Toftegaard, Thomas Skjødeberg

    2007-01-01

    In this paper we focus on adaptive modulation strategies for multicast service in orthogonal frequency division multiple access systems. A reward function has been defined as the optimization target, which includes both the average user throughput and bit error rate. We also developed an adaptive...... modulation strategy, namely local best reward strategy, to maximize this reward function. The performance of different modulation strategies are compared in different SNR distribution scenarios, and the optimum strategy in each scenario is suggested....

  19. Out-of-Sequence Preventative Cell Dispatching for Multicast Input-Queued Space-Memory-Memory Clos-Network

    DEFF Research Database (Denmark)

    Yu, Hao; Ruepp, Sarah Renée; Berger, Michael Stübert

    2011-01-01

    This paper proposes two out-of-sequence (OOS) preventative cell dispatching algorithms for the multicast input-queued space-memory-memory (IQ-SMM) Clos-network switch architecture, i.e. the multicast flow-based DSRR (MF-DSRR) and the multicast flow-based round-robin (MFRR). Treating each cell...

  20. Adaptive live multicast video streaming of SVC with UEP FEC

    Science.gov (United States)

    Lev, Avram; Lasry, Amir; Loants, Maoz; Hadar, Ofer

    2014-09-01

    Ideally, video streaming systems should provide the best quality video a user's device can handle without compromising on downloading speed. In this article, an improved video transmission system is presented which dynamically enhances the video quality based on a user's current network state and repairs errors from data lost in the video transmission. The system incorporates three main components: Scalable Video Coding (SVC) with three layers, multicast based on Receiver Layered Multicast (RLM) and an UnEqual Forward Error Correction (FEC) algorithm. The SVC provides an efficient method for providing different levels of video quality, stored as enhancement layers. In the presented system, a proportional-integral-derivative (PID) controller was implemented to dynamically adjust the video quality, adding or subtracting quality layers as appropriate. In addition, an FEC algorithm was added to compensate for data lost in transmission. A two dimensional FEC was used. The FEC algorithm came from the Pro MPEG code of practice #3 release 2. Several bit errors scenarios were tested (step function, cosine wave) with different bandwidth size and error values were simulated. The suggested scheme which includes SVC video encoding with 3 layers over IP Multicast with Unequal FEC algorithm was investigated under different channel conditions, variable bandwidths and different bit error rates. The results indicate improvement of the video quality in terms of PSNR over previous transmission schemes.

  1. Simultaneous multichannel wavelength multicasting and XOR logic gate multicasting for three DPSK signals based on four-wave mixing in quantum-dot semiconductor optical amplifier.

    Science.gov (United States)

    Qin, Jun; Lu, Guo-Wei; Sakamoto, Takahide; Akahane, Kouichi; Yamamoto, Naokatsu; Wang, Danshi; Wang, Cheng; Wang, Hongxiang; Zhang, Min; Kawanishi, Tetsuya; Ji, Yuefeng

    2014-12-01

    In this paper, we experimentally demonstrate simultaneous multichannel wavelength multicasting (MWM) and exclusive-OR logic gate multicasting (XOR-LGM) for three 10Gbps non-return-to-zero differential phase-shift-keying (NRZ-DPSK) signals in quantum-dot semiconductor optical amplifier (QD-SOA) by exploiting the four-wave mixing (FWM) process. No additional pump is needed in the scheme. Through the interaction of the input three 10Gbps DPSK signal lights in QD-SOA, each channel is successfully multicasted to three wavelengths (1-to-3 for each), totally 3-to-9 MWM, and at the same time, three-output XOR-LGM is obtained at three different wavelengths. All the new generated channels are with a power penalty less than 1.2dB at a BER of 10(-9). Degenerate and non-degenerate FWM components are fully used in the experiment for data and logic multicasting.

  2. OPTIMASI OLSR ROUTING PROTOCOL PADA JARINGAN WIRELESS MESH DENGAN ADAPTIVE REFRESHING TIME INTERVAL DAN ENHANCE MULTI POINT RELAY SELECTING ALGORITHM

    Directory of Open Access Journals (Sweden)

    Faosan Mapa

    2014-01-01

    Full Text Available Normal 0 false false false IN X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Wireless Mesh Network (WMN adalah suatu konektivitas jaringan yang self-organized, self-configured dan multi-hop. Tujuan dari WMN adalah menawarkan pengguna suatu bentuk jaringan nirkabel yang dapat dengan mudah berkomunikasi dengan jaringan konvensional dengan kecepatan tinggi dan dengan cakupan yang lebih luas serta biaya awal yang minimal. Diperlukan suatu desain protokol routing yang efisien untuk WMN yang secara adaptif dapat mendukung mesh routers dan mesh clients. Dalam tulisan ini, diusulkan untuk mengoptimalkan protokol OLSR, yang merupakan protokol routing proaktif. Digunakan heuristik yang meningkatkan protokol OLSR melalui adaptive refreshing time interval dan memperbaiki metode MPR selecting algorithm. Suatu analisa dalam meningkatkan protokol OLSR melalui adaptive refreshing time interval dan memperbaiki algoritma pemilihan MPR menunjukkan kinerja yang signifikan dalam hal throughput jika dibandingkan dengan protokol OLSR yang asli. Akan tetapi, terdapat kenaikan dalam hal delay. Pada simulasi yang dilakukan dapat disimpulkan bahwa OLSR dapat dioptimalkan dengan memodifikasi pemilihan node MPR berdasarkan cost effective dan penyesuaian waktu interval refreshing hello message sesuai dengan keadaan

  3. An Efficient SDN Multicast Architecture for Dynamic Industrial IoT Environments

    Directory of Open Access Journals (Sweden)

    Hyeong-Su Kim

    2018-01-01

    Full Text Available Large-scale industrial IoT services appear in smart factory domains such as factory clouds which integrate distributed small factories into a large virtual factory with dynamic combination based on orders of consumers. A smart factory has so many industrial elements including various sensors/actuators, gateways, controllers, application servers, and IoT clouds. Since there are complex connections and relations, it is hard to handle them in point-to-point manner. In addition, many duplicated traffics are exchanged between them through the Internet. Multicast is believed as an effective many-to-many communication mechanism by establishing multicast trees between sources and receivers. There are, however, some issues for adopting multicast to large-scale industrial IoT services in terms of QoS. In this paper, we propose a novel software-defined network multicast based on group shared tree which includes near-receiver rendezvous point selection algorithm and group shared tree switching mechanism. As a result, the proposed multicast mechanism can reduce the packet loss by 90% compared to the legacy methods under severe congestion condition. GST switching method obtains to decreased packet delay effect, respectively, 2%, 20% better than the previously studied multicast and the legacy SDN multicast.

  4. Minimum Interference Channel Assignment Algorithm for Multicast in a Wireless Mesh Network

    Directory of Open Access Journals (Sweden)

    Sangil Choi

    2016-12-01

    Full Text Available Wireless mesh networks (WMNs have been considered as one of the key technologies for the configuration of wireless machines since they emerged. In a WMN, wireless routers provide multi-hop wireless connectivity between hosts in the network and also allow them to access the Internet via gateway devices. Wireless routers are typically equipped with multiple radios operating on different channels to increase network throughput. Multicast is a form of communication that delivers data from a source to a set of destinations simultaneously. It is used in a number of applications, such as distributed games, distance education, and video conferencing. In this study, we address a channel assignment problem for multicast in multi-radio multi-channel WMNs. In a multi-radio multi-channel WMN, two nearby nodes will interfere with each other and cause a throughput decrease when they transmit on the same channel. Thus, an important goal for multicast channel assignment is to reduce the interference among networked devices. We have developed a minimum interference channel assignment (MICA algorithm for multicast that accurately models the interference relationship between pairs of multicast tree nodes using the concept of the interference factor and assigns channels to tree nodes to minimize interference within the multicast tree. Simulation results show that MICA achieves higher throughput and lower end-to-end packet delay compared with an existing channel assignment algorithm named multi-channel multicast (MCM. In addition, MICA achieves much lower throughput variation among the destination nodes than MCM.

  5. The MIM web gateway to IP multicast e-meetings

    Science.gov (United States)

    Parviainen, Roland; Parnes, Peter

    2003-12-01

    As video conferencing and e-meeting systems are used more and more on the Internet and in businesses it becomes increasingly important to be able to participate from any computer at any location. Often this is impossible, since these systems requires often special software that are not available everywhere or impossible to install for administrative reasons. Many locations also lack the necessary network infrastructure such as IP multicast. This paper presents a WWW gateway system that enables users to participate using only a standard web browser. The design and architecture of the system are described and performance tests that show the scalability of the system are also presented.

  6. Ruteo multicast mediante algoritmos genéticos

    OpenAIRE

    Klenzi, Raúl O.; Sánchez Tores, Héctor A.; Ortega, Manuel Oscar; Naranjo, Viviana; Espósito, Gabriela

    2000-01-01

    Los sistemas o redes de comunicación construidos teniendo en cuenta el modelo de referencia OSI (Open Systems lnterconection) o la arquitectura de Internet, fueron diseñados para soportar servicios o comunicaciones punto a punto, donde la información fluye entre dos usuarios únicamente. Uno de los tópicos en el cual las redes de computadoras actuales están poniendo mucho énfasis, proviene de las aplicaciones multicast o de grupo. Estas involucran más de dos usuarios (estos usuarios definen...

  7. Resource Allocation Management for Broadcast/Multicast Services

    OpenAIRE

    Fuente Iglesias, Alejandro de la; Pérez Leal, Raquel; García-Armada, Ana

    2015-01-01

    Ponencia presentada en: XXX Simposium Nacional de la Unión Científica Internacional de Radio, los dias 2 y 4 septiembre 2015, en Pamplona (españa). Video services are expected to become more than 70% of the mobile traffic in 2020. Broadcast and multicast service is the most efficient mechanism to deliver the same content to many users. Not only focusing on venue casting, but also distributing many other media such as software updates and breaking news, 5G broadcasting is a key driver to a...

  8. Network connectivity enhancement by exploiting all optical multicast in semiconductor ring laser

    Science.gov (United States)

    Siraj, M.; Memon, M. I.; Shoaib, M.; Alshebeili, S.

    2015-03-01

    The use of smart phone and tablet applications will provide the troops for executing, controlling and analyzing sophisticated operations with the commanders providing crucial documents directly to troops wherever and whenever needed. Wireless mesh networks (WMNs) is a cutting edge networking technology which is capable of supporting Joint Tactical radio System (JTRS).WMNs are capable of providing the much needed bandwidth for applications like hand held radios and communication for airborne and ground vehicles. Routing management tasks can be efficiently handled through WMNs through a central command control center. As the spectrum space is congested, cognitive radios are a much welcome technology that will provide much needed bandwidth. They can self-configure themselves, can adapt themselves to the user requirement, provide dynamic spectrum access for minimizing interference and also deliver optimal power output. Sometimes in the indoor environment, there are poor signal issues and reduced coverage. In this paper, a solution utilizing (CR WMNs) over optical network is presented by creating nanocells (PCs) inside the indoor environment. The phenomenon of four-wave mixing (FWM) is exploited to generate all-optical multicast using semiconductor ring laser (SRL). As a result same signal is transmitted at different wavelengths. Every PC is assigned a unique wavelength. By using CR technology in conjunction with PC will not only solve network coverage issue but will provide a good bandwidth to the secondary users.

  9. Predicting Catastrophic BGP Routing Instabilities

    National Research Council Canada - National Science Library

    Nguyen, Lien

    2004-01-01

    .... Currently, this critical function is performed by the Border Gateway Protocol (BGP) version 4 RF01771. Like all routing protocols, BGP is vulnerable to instabilities that reduce its effectiveness...

  10. Multihop Wireless Networks Opportunistic Routing

    CERN Document Server

    Zeng, Kai; Li, Ming

    2011-01-01

    This book provides an introduction to opportunistic routing an emerging technology designed to improve the packet forwarding reliability, network capacity and energy efficiency of multihop wireless networks This book presents a comprehensive background to the technological challenges lying behind opportunistic routing. The authors cover many fundamental research issues for this new concept, including the basic principles, performance limit and performance improvement of opportunistic routing compared to traditional routing, energy efficiency and distributed opportunistic routing protocol desig

  11. Throughput, Energy and Overhead of Multicast Device-to-Device Communications with Network Coded Cooperation

    DEFF Research Database (Denmark)

    Hernandez, Nestor; Heide, Janus; Roetter, Daniel Enrique Lucani

    2017-01-01

    , this assumes that the throughput gains and energy savings in multicasting are much larger between devices than the base station to the receivers. However, current mobile networks suffer from many different issues varying the performance in data rates, which calls into question these assumptions. Therefore......, a first objective of this work is to assess the operating regions where employing cooperation results in higher throughput and/or energy savings. We consider multicast scenarios with network coded mechanisms employing Random Linear Network Coding (RLNC). However, although RLNC is good for low amount...... of transmissions in multicast, it has an inherent overhead from extreme high or low field related caveats. Thus, as a second objective, we review and propose the application of new network codes that posses low overhead for multicasting, by having a short representation and low dependence probability. We provide...

  12. Dynamic segment shared protection for multicast traffic in meshed wavelength-division-multiplexing optical networks

    Science.gov (United States)

    Liao, Luhua; Li, Lemin; Wang, Sheng

    2006-12-01

    We investigate the protection approach for dynamic multicast traffic under shared risk link group (SRLG) constraints in meshed wavelength-division-multiplexing optical networks. We present a shared protection algorithm called dynamic segment shared protection for multicast traffic (DSSPM), which can dynamically adjust the link cost according to the current network state and can establish a primary light-tree as well as corresponding SRLG-disjoint backup segments for a dependable multicast connection. A backup segment can efficiently share the wavelength capacity of its working tree and the common resources of other backup segments based on SRLG-disjoint constraints. The simulation results show that DSSPM not only can protect the multicast sessions against a single-SRLG breakdown, but can make better use of the wavelength resources and also lower the network blocking probability.

  13. Efficient round-robin multicast scheduling for input-queued switches

    DEFF Research Database (Denmark)

    Rasmussen, Anders; Yu, Hao; Ruepp, Sarah Renée

    2014-01-01

    The input-queued (IQ) switch architecture is favoured for designing multicast high-speed switches because of its scalability and low implementation complexity. However, using the first-in-first-out (FIFO) queueing discipline at each input of the switch may cause the head-of-line (HOL) blocking...... problem. Using a separate queue for each output port at an input to reduce the HOL blocking, that is, the virtual output queuing discipline, increases the implementation complexity, which limits the scalability. Given the increasing link speed and network capacity, a low-complexity yet efficient multicast...... by means of queue look-ahead. Simulation results demonstrate that this FIFO-based IQ multicast architecture is able to achieve significant improvements in terms of multicast latency requirements by searching through a small number of cells beyond the HOL cells in the input queues. Furthermore, hardware...

  14. Ancestors protocol for scalable key management

    Directory of Open Access Journals (Sweden)

    Dieter Gollmann

    2010-06-01

    Full Text Available Group key management is an important functional building block for secure multicast architecture. Thereby, it has been extensively studied in the literature. The main proposed protocol is Adaptive Clustering for Scalable Group Key Management (ASGK. According to ASGK protocol, the multicast group is divided into clusters, where each cluster consists of areas of members. Each cluster uses its own Traffic Encryption Key (TEK. These clusters are updated periodically depending on the dynamism of the members during the secure session. The modified protocol has been proposed based on ASGK with some modifications to balance the number of affected members and the encryption/decryption overhead with any number of the areas when a member joins or leaves the group. This modified protocol is called Ancestors protocol. According to Ancestors protocol, every area receives the dynamism of the members from its parents. The main objective of the modified protocol is to reduce the number of affected members during the leaving and joining members, then 1 affects n overhead would be reduced. A comparative study has been done between ASGK protocol and the modified protocol. According to the comparative results, it found that the modified protocol is always outperforming the ASGK protocol.

  15. Bit rate maximization for multicast LP-OFDM systems in PLC context

    OpenAIRE

    Maiga , Ali; Baudais , Jean-Yves; Hélard , Jean-François

    2009-01-01

    ISBN: 978-88-900984-8-2.; International audience; In this paper, we propose a new resource allocation algorithm based on linear precoding technique for multicast OFDM systems. Linear precoding technique applied to OFDM systems has already proved its ability to significantly increase the system throughput in a powerline communication (PLC) context. Simulations through PLC channels show that this algorithm outperforms the classical multicast method (up to 7.3% bit rate gain) and gives better pe...

  16. History-based Adaptive Modulation for a Downlink Multicast Channel in OFDMA systems

    DEFF Research Database (Denmark)

    Wang, Haibo; Schwefel, Hans-Peter; Toftegaard, Thomas Skjødeberg

    2008-01-01

    In this paper we investigated the adaptive modulation strategies for Multicast service in orthogonal frequency division multiple access systems. We defined a Reward function as the performance optimization target and developed adaptive modulation strategies to maximize this Reward function....... The proposed optimization algorithm varied the instantaneous BER constraint of each mobile Multicast receiver according to its individual cumulated BER, which resulted in a significant Reward gain....

  17. Polarization Insensitive One-to-Six WDM Multicasting in a Silicon Nanowire

    DEFF Research Database (Denmark)

    Pu, Minhao; Hu, Hao; Peucheret, Christophe

    2012-01-01

    We present polarization insensitive one-to-six WDM multicasting based on nondegenerate four-wave mixing in a silicon nanowire with angled-pump scheme. Bit-error rate measurements are performed and error-free operation is achieved.......We present polarization insensitive one-to-six WDM multicasting based on nondegenerate four-wave mixing in a silicon nanowire with angled-pump scheme. Bit-error rate measurements are performed and error-free operation is achieved....

  18. Beyond Traditional DTN Routing: Social Networks for Opportunistic Communication

    OpenAIRE

    Schurgot, Mary R.; Comaniciu, Cristina; Jaffrès-Runser, Katia

    2011-01-01

    This article examines the evolution of routing protocols for intermittently connected ad hoc networks and discusses the trend toward social-based routing protocols. A survey of current routing solutions is presented, where routing protocols for opportunistic networks are classified based on the network graph employed. The need to capture performance tradeoffs from a multi-objective perspective is highlighted.

  19. Preventing Out-of-Sequence for Multicast Input-Queued Space-Memory-Memory Clos-Network

    DEFF Research Database (Denmark)

    Yu, Hao; Ruepp, Sarah Renée; Berger, Michael Stübert

    2011-01-01

    This paper proposes an out-of-sequence (OOS) preventative cell dispatching algorithm, the multicast flow-based round robin (MFRR), for multicast input-queued space-memory-memory (IQ-SMM) Clos-network architecture. Independently treating each incoming cell, such as the desynchronized static round...

  20. Symmetric cryptographic protocols

    CERN Document Server

    Ramkumar, Mahalingam

    2014-01-01

    This book focuses on protocols and constructions that make good use of symmetric pseudo random functions (PRF) like block ciphers and hash functions - the building blocks for symmetric cryptography. Readers will benefit from detailed discussion of several strategies for utilizing symmetric PRFs. Coverage includes various key distribution strategies for unicast, broadcast and multicast security, and strategies for constructing efficient digests of dynamic databases using binary hash trees.   •        Provides detailed coverage of symmetric key protocols •        Describes various applications of symmetric building blocks •        Includes strategies for constructing compact and efficient digests of dynamic databases

  1. Mobility Based Key Management Technique for Multicast Security in Mobile Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    B. Madhusudhanan

    2015-01-01

    Full Text Available In MANET multicasting, forward and backward secrecy result in increased packet drop rate owing to mobility. Frequent rekeying causes large message overhead which increases energy consumption and end-to-end delay. Particularly, the prevailing group key management techniques cause frequent mobility and disconnections. So there is a need to design a multicast key management technique to overcome these problems. In this paper, we propose the mobility based key management technique for multicast security in MANET. Initially, the nodes are categorized according to their stability index which is estimated based on the link availability and mobility. A multicast tree is constructed such that for every weak node, there is a strong parent node. A session key-based encryption technique is utilized to transmit a multicast data. The rekeying process is performed periodically by the initiator node. The rekeying interval is fixed depending on the node category so that this technique greatly minimizes the rekeying overhead. By simulation results, we show that our proposed approach reduces the packet drop rate and improves the data confidentiality.

  2. Security Enhancement for Multicast over Internet of Things by Dynamically Constructed Fountain Codes

    Directory of Open Access Journals (Sweden)

    Qinghe Du

    2018-01-01

    Full Text Available The Internet of Things (IoT is expected to accommodate every object which exists in this world or likely to exist in the near future. The enormous scale of the objects is challenged by big security concerns, especially for common information dissemination via multicast services, where the reliability assurance for multiple multicast users at the cost of increasing redundancy and/or retransmissions also benefits eavesdroppers in successfully decoding the overheard signals. The objective of this work is to address the security challenge present in IoT multicast applications. Specifically, with the presence of the eavesdropper, an adaptive fountain code design is proposed in this paper to enhance the security for multicast in IoT. The main novel features of the proposed scheme include two folds: (i dynamical encoding scheme which can effectively decrease intercept probability at the eavesdropper; (ii increasing the transmission efficiency compared with the conventional nondynamical design. The analysis and simulation results show that the proposed scheme can effectively enhance information security while achieving higher transmission efficiency with a little accredited complexity, thus facilitating the secured wireless multicast transmissions over IoT.

  3. Link importance incorporated failure probability measuring solution for multicast light-trees in elastic optical networks

    Science.gov (United States)

    Li, Xin; Zhang, Lu; Tang, Ying; Huang, Shanguo

    2018-03-01

    The light-tree-based optical multicasting (LT-OM) scheme provides a spectrum- and energy-efficient method to accommodate emerging multicast services. Some studies focus on the survivability technologies for LTs against a fixed number of link failures, such as single-link failure. However, a few studies involve failure probability constraints when building LTs. It is worth noting that each link of an LT plays different important roles under failure scenarios. When calculating the failure probability of an LT, the importance of its every link should be considered. We design a link importance incorporated failure probability measuring solution (LIFPMS) for multicast LTs under independent failure model and shared risk link group failure model. Based on the LIFPMS, we put forward the minimum failure probability (MFP) problem for the LT-OM scheme. Heuristic approaches are developed to address the MFP problem in elastic optical networks. Numerical results show that the LIFPMS provides an accurate metric for calculating the failure probability of multicast LTs and enhances the reliability of the LT-OM scheme while accommodating multicast services.

  4. Enhanced first-in-first-out-based round-robin multicast scheduling algorithm for input-queued switches

    DEFF Research Database (Denmark)

    Yu, Hao; Ruepp, Sarah Renée; Berger, Michael Stübert

    2011-01-01

    This study focuses on the multicast scheduling for M × N input-queued switches. An enhanced first-in-first-out -based round-robin multicast scheduling algorithm is proposed with a function of searching deeper into queues to reduce the head-of-line (HOL) blocking problem and thereby the multicast...... out on the decision matrix to reduce the number of transmission for each cell. To reduce the HOL blocking problem, a complement matrix is constructed based on the traffic matrix and the decision matrix, and a process of searching deeper into the queues is carried out to find cells that can be sent...... to the idle outputs. Simulation results show that the proposed function of searching deeper into the queues can alleviate the HOL blocking and as a result reduce the multicast latency significantly. Under both balanced and unbalanced multicast traffic, the proposed algorithm is able to maintain a stable...

  5. Adaptive Demand-Driven Multicast Routing in Multi-Hop Wireless Ad Hoc Networks

    National Research Council Canada - National Science Library

    Jetcheva, Jorjeta G

    2004-01-01

    ...) nodes that wish to communicate. Each node in the ad hoc network acts as a router and forwards packets on behalf of other nodes, allowing nodes that are not within wireless range of each other to communicate over multi-hop paths...

  6. On-Chip SDM Switching for Unicast, Multicast and Traffic Grooming in Data Center Networks

    DEFF Research Database (Denmark)

    Kamchevska, Valerija; Ding, Yunhong; Dalgaard, Kjeld

    2017-01-01

    This paper reports on the use of a novel photonic integrated circuit that facilitates multicast and grooming in an optical data center architecture. The circuit allows for on-chip spatial multiplexing and demultiplexing as well as fiber core switching. Using this device, we experimentally verify...... that multicast and/or grooming can be successfully performed along the full range of output ports, for different group size and different power ratio. Moreover, we experimentally demonstrate SDM transmission and 5 Tbit/s switching using the on-chip fiber switch with integrated fan-in/fan-out devices and achieve...... errorfree performance (BER≤10-9) for a network scenario including simultaneous unicast/multicast switching and traffic grooming....

  7. A Grooming Nodes Optimal Allocation Method for Multicast in WDM Networks

    Directory of Open Access Journals (Sweden)

    Chengying Wei

    2016-01-01

    Full Text Available The grooming node has the capability of grooming multicast traffic with the small granularity into established light at high cost of complexity and node architecture. In the paper, a grooming nodes optimal allocation (GNOA method is proposed to optimize the allocation of the grooming nodes constraint by the blocking probability for multicast traffic in sparse WDM networks. In the proposed GNOA method, the location of each grooming node is determined by the SCLD strategy. The improved smallest cost largest degree (SCLD strategy is designed to select the nongrooming nodes in the proposed GNOA method. The simulation results show that the proposed GNOA method can reduce the required number of grooming nodes and decrease the cost of constructing a network to guarantee a certain request blocking probability when the wavelengths per fiber and transmitter/receiver ports per node are sufficient for the optical multicast in WDM networks.

  8. Multicast backup reprovisioning problem for Hamiltonian cycle-based protection on WDM networks

    Science.gov (United States)

    Din, Der-Rong; Huang, Jen-Shen

    2014-03-01

    As networks grow in size and complexity, the chance and the impact of failures increase dramatically. The pre-allocated backup resources cannot provide 100% protection guarantee when continuous failures occur in a network. In this paper, the multicast backup re-provisioning problem (MBRP) for Hamiltonian cycle (HC)-based protection on WDM networks for the link-failure case is studied. We focus on how to recover the protecting capabilities of Hamiltonian cycle against the subsequent link-failures on WDM networks for multicast transmissions, after recovering the multicast trees affected by the previous link-failure. Since this problem is a hard problem, an algorithm, which consists of several heuristics and a genetic algorithm (GA), is proposed to solve it. The simulation results of the proposed method are also given. Experimental results indicate that the proposed algorithm can solve this problem efficiently.

  9. Analysis and Optimization of Sparse Random Linear Network Coding for Reliable Multicast Services

    DEFF Research Database (Denmark)

    Tassi, Andrea; Chatzigeorgiou, Ioannis; Roetter, Daniel Enrique Lucani

    2016-01-01

    Point-to-multipoint communications are expected to play a pivotal role in next-generation networks. This paper refers to a cellular system transmitting layered multicast services to a multicast group of users. Reliability of communications is ensured via different random linear network coding (RLNC......) techniques. We deal with a fundamental problem: the computational complexity of the RLNC decoder. The higher the number of decoding operations is, the more the user's computational overhead grows and, consequently, the faster the battery of mobile devices drains. By referring to several sparse RLNC...... techniques, and without any assumption on the implementation of the RLNC decoder in use, we provide an efficient way to characterize the performance of users targeted by ultra-reliable layered multicast services. The proposed modeling allows to efficiently derive the average number of coded packet...

  10. Opportunistic Relay Selection in Multicast Relay Networks using Compressive Sensing

    KAUST Repository

    Elkhalil, Khalil

    2014-12-01

    Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. However, for relay selection algorithms to make a selection decision, channel state information (CSI) from all cooperating relays is usually required at a central node. This requirement poses two important challenges. Firstly, CSI acquisition generates a great deal of feedback overhead (air-time) that could result in significant transmission delays. Secondly, the fed back channel information is usually corrupted by additive noise. This could lead to transmission outages if the central node selects the set of cooperating relays based on inaccurate feedback information. In this paper, we introduce a limited feedback relay selection algorithm for a multicast relay network. The proposed algorithm exploits the theory of compressive sensing to first obtain the identity of the “strong” relays with limited feedback. Following that, the CSI of the selected relays is estimated using linear minimum mean square error estimation. To minimize the effect of noise on the fed back CSI, we introduce a back-off strategy that optimally backs-off on the noisy estimated CSI. For a fixed group size, we provide closed form expressions for the scaling law of the maximum equivalent SNR for both Decode and Forward (DF) and Amplify and Forward (AF) cases. Numerical results show that the proposed algorithm drastically reduces the feedback air-time and achieves a rate close to that obtained by selection algorithms with dedicated error-free feedback channels.

  11. Multicast in Femtocell Networks: A Successive Interference Cancellation Approach

    Directory of Open Access Journals (Sweden)

    Donglin Hu

    2014-09-01

    Full Text Available A femtocell is a small cellular base station (BS, typically used for serving approved users within a small coverage. In this paper, we investigate the problem of data multicast in femtocell networks that incorporates superposition coding (SC and successive interference cancellation (SIC. The problem is to decide the transmission schedule for each BS, as well as the power allocation for the SC layers, to achieve a sufficiently large SNR for each layer to be decodable with SIC at each user. Minimizing the total BS power consumption achieves the goal of “green” communications. We formulate a Mixed Integer Nonlinear Programming (MINLP problem, and then reformulate the problem into a simpler form. Upper and lower performance bounds on the total BS power consumption are derived. Finally, we consider three typical connection scenarios, and develop optimal and nearoptimal algorithms for the three scenarios. The proposed algorithms have low computational complexity, and outperform a heuristic scheme with considerable gains in our simulation study.

  12. Linear and non-linear video and TV applications using IPv6 and IPv6 multicast

    CERN Document Server

    Minoli, Daniel

    2012-01-01

    Provides options for implementing IPv6 and IPv6 multicast in service provider networks New technologies, viewing paradigms, and content distribution approaches are taking the TV/video services industry by storm. Linear and Nonlinear Video and TV Applications: Using IPv6 and IPv6 Multicast identifies five emerging trends in next-generation delivery of entertainment-quality video. These trends are observable and can be capitalized upon by progressive service providers, telcos, cable operators, and ISPs. This comprehensive guide explores these evolving directions in the TV/v

  13. QoS and QoE Aware N-Screen Multicast Service

    Directory of Open Access Journals (Sweden)

    Ghulam Sarwar

    2016-01-01

    Full Text Available The paper focuses on ensuring the quality-of-service (QoS and quality-of-experience (QoE requirements of users having heterogeneous devices in a multicast session. QoS parameters such as bit rate, delays, and packet losses are good indicators for optimizing network services but fall short in characterizing user perception (QoE. In N-Screen service, the users have different devices with heterogeneous attributes like screen size, resolution, and access network interface, and the users have different QoE on N-Screen devices with the same QoS parameters. We formulate the objective function of the N-Screen multicast grouping to ensure the minimum user’s QoE with smaller bandwidth requirement. We propose a dynamic user reassignment scheme to maintain and satisfy the QoE by adapting the user’s membership to the varying network conditions. The proposed schemes combine the available bandwidth and multimedia visual quality to ensure the QoS and QoE. In the network architecture, we introduce the functions of the QoS and QoE aware multicast group management and the estimation schemes for the QoS and QoE parameters. The simulation results show that the proposed multicast service ensures the network QoS and guarantees the QoE of users in the varying network conditions.

  14. Joint NC-ARQ and AMC for QoS-Guaranteed Mobile Multicast

    DEFF Research Database (Denmark)

    Toftegaard, Thomas Skjødeberg; Wang, Haibo; Schwefel, Hans-Peter

    2010-01-01

    the scalability problem of applying ARQ in multicast. Then we propose two joint NC-ARQ-AMC schemes, namely, the Average PER-based AMC (AvgPER-AMC) with Opt-ARQ and AvgPER-AMC with SubOpt-ARQ in a cross-layer design framework to maximize the average spectral efficiency per receiver under specific QoS constraints...

  15. Almost optimal distributed M2M multicasting in wireless mesh networks

    DEFF Research Database (Denmark)

    Xin, Qin; Manne, Fredrik; Zhang, Yan

    2012-01-01

    Wireless Mesh Networking (WMN) is an emerging communication paradigm to enable resilient, cost-efficient and reliable services for the future-generation wireless networks. In this paper, we study the problem of multipoint-to- multipoint (M2M) multicasting in a WMN which aims to use the minimum nu...

  16. Delay Bounded Multi-Source Multicast in Software-Defined Networking

    Directory of Open Access Journals (Sweden)

    Thabo Semong

    2018-01-01

    Full Text Available Software-Defined Networking (SDN is the next generation network architecture with exciting application prospects. The control function in SDN is decoupled from the data forwarding plane, hence it provides a new centralized architecture with flexible network resource management. Although SDN is attracting much attention from both industry and research, its advantage over the traditional networks has not been fully utilized. Multicast is designed to deliver content to multiple destinations. The current traffic engineering in SDN focuses mainly on unicast, however, multicast can effectively reduce network resource consumption by serving multiple clients. This paper studies a novel delay-bounded multi-source multicast SDN problem, in which among the set of potential sources, we select a source to build the multicast-tree, under the constraint that the transmission delay for every destination is bounded. This problem is more difficult than the traditional Steiner minimum tree (SMT problem, since it needs to find a source from the set of all potential sources. We model the problem as a mixed-integer linear programming (MILP and prove its NP-Hardness. To solve the problem, a delay bounded multi-source (DBMS scheme is proposed, which includes a DBMS algorithm to build a minimum delay cost DBMS-Forest. Through a MATLAB experiment, we demonstrate that DBMS is significantly more efficient and outperforms other existing algorithms in the literature.

  17. All-optical broadcast and multicast technologies based on PPLN waveguide

    DEFF Research Database (Denmark)

    Ye, Lingyun; Wang, Ju; Hu, Hao

    2013-01-01

    All-optical 1×4 broadcast and 1×3 multicast experiments of a 40-Gb/s return-to-zero on-off keying (RZ-OOK) signal based on a periodically poled lithium niobate (PPLN) waveguide are demonstrated in this letter. Clear opened eye diagrams and error-free performance are achieved for the broadcast...

  18. Energy-minimized design in all-optical networks using unicast/multicast traffic grooming

    Science.gov (United States)

    Puche, William S.; Amaya, Ferney O.; Sierra, Javier E.

    2013-09-01

    The increased bandwidth required by applications, tends to raise the amount of optical equipment, for this reason, it is essential to maintain a balance between the wavelength allocation, available capacity and number of optical devices to achieve the lowest power consumption. You could say that we propose a model that minimizes energy consumption, using unicast / multicast traffic grooming in optical networks.

  19. Demonstration of flexible multicasting and aggregation functionality for TWDM-PON

    Science.gov (United States)

    Chen, Yuanxiang; Li, Juhao; Zhu, Paikun; Zhu, Jinglong; Tian, Yu; Wu, Zhongying; Peng, Huangfa; Xu, Yongchi; Chen, Jingbiao; He, Yongqi; Chen, Zhangyuan

    2017-06-01

    The time- and wavelength-division multiplexed passive optical network (TWDM-PON) has been recognized as an attractive solution to provide broadband access for the next-generation networks. In this paper, we propose flexible service multicasting and aggregation functionality for TWDM-PON utilizing multiple-pump four-wave-mixing (FWM) and cyclic arrayed waveguide grating (AWG). With the proposed scheme, multiple TWDM-PON links share a single optical line terminal (OLT), which can greatly reduce the network deployment expense and achieve efficient network resource utilization by load balancing among different optical distribution networks (ODNs). The proposed scheme is compatible with existing TDM-PON infrastructure with fixed-wavelength OLT transmitter, thus smooth service upgrade can be achieved. Utilizing the proposed scheme, we demonstrate a proof-of-concept experiment with 10-Gb/s OOK and 10-Gb/s QPSK orthogonal frequency division multiplexing (OFDM) signal multicasting and aggregating to seven PON links. Compared with back-to-back (BTB) channel, the newly generated multicasting OOK signal and OFDM signal have power penalty of 1.6 dB and 2 dB at the BER of 10-3, respectively. For the aggregation of multiple channels, no obvious power penalty is observed. What is more, to verify the flexibility of the proposed scheme, we reconfigure the wavelength selective switch (WSS) and adjust the number of pumps to realize flexible multicasting functionality. One to three, one to seven, one to thirteen and one to twenty-one multicasting are achieved without modifying OLT structure.

  20. Resource management in energy-limited, bandwidth-limited, transceiver-limited wireless networks for session-based multicasting

    National Research Council Canada - National Science Library

    Wieselthier, Jeffrey E; Nguyen, Gam D; Ephremides, Anthony

    2001-01-01

    In this paper we consider source-initiated multicast session traffic in an ad hoc wireless network, operating under hard constraints on the available transmission energy as well as on bandwidth and transceiver resources...

  1. Near-field self-interference cancellation and quality of service multicast beamforming in full-duplex

    Science.gov (United States)

    Wu, Fei; Shao, Shihai; Tang, Youxi

    2016-10-01

    To enable simultaneous multicast downlink transmit and receive operations on the same frequency band, also known as full-duplex links between an access point and mobile users. The problem of minimizing the total power of multicast transmit beamforming is considered from the viewpoint of ensuring the suppression amount of near-field line-of-sight self-interference and guaranteeing prescribed minimum signal-to-interference-plus-noise-ratio (SINR) at each receiver of the multicast groups. Based on earlier results for multicast groups beamforming, the joint problem is easily shown to be NP-hard. A semidefinite relaxation (SDR) technique with linear program power adjust method is proposed to solve the NP-hard problem. Simulation shows that the proposed method is feasible even when the local receive antenna in nearfield and the mobile user in far-filed are in the same direction.

  2. Source Authentication for Multicast in Mobile Ad Hoc Networks

    National Research Council Canada - National Science Library

    Ramachandran, Prabha

    2003-01-01

    Recent emergence and popularity of mobile ad hoc networks in a host of current-day applications has instigated a suite of research challenges, primarily in routing and security issues for such networks...

  3. Energy Efficient Routing in Nomadic Networks

    DEFF Research Database (Denmark)

    Kristensen, Mads Darø; Bouvin, Niels Olof

    2007-01-01

    We present an evaluation of a novel energy-efficient routing protocol for mobile ad-hoc networks. We combine two techniques for optimizing energy levels with a well-known routing protocol. We examine the behavior of this combination in a nomadic network setting, where some nodes are stationary...

  4. Energy-Efficient Multicast Transmission for Underlay Device-to-Device Communications: A Social-Aware Perspective

    Directory of Open Access Journals (Sweden)

    Fan Jiang

    2017-01-01

    Full Text Available In this paper, by utilizing the social relationships among mobile users, we present a framework of energy-efficient cluster formation and resource allocation for multicast D2D transmission. In particular, we first deal with D2D multicast cluster/group formation strategy from both physical distance and social trust level. Then we aim to maximize the overall energy-efficiency of D2D multicast groups through resource allocation and power control scheme, which considers the quality-of-service (QoS requirements of both cellular user equipment and D2D groups. A heuristic algorithm is proposed to solve above energy-efficiency problem with less complexity. After that, considering the limited battery capacity of mobile users, we propose an energy and social aware cluster head update algorithm, which incorporates both the energy constraint and social centrality measurement. Numerical results indicate that the proposed social-tie based D2D multicast group formation and update algorithm form a multicast group in an energy efficient way. Moreover, the proposed resource and power allocation scheme achieves better energy efficiency in terms of throughput per energy consumption. These results show that, by exploiting social domain information, underlay D2D multicast transmission has high practical potential in saving the source on wireless links and in the backhaul.

  5. A reliable transmission protocol for ZigBee-based wireless patient monitoring.

    Science.gov (United States)

    Chen, Shyr-Kuen; Kao, Tsair; Chan, Chia-Tai; Huang, Chih-Ning; Chiang, Chih-Yen; Lai, Chin-Yu; Tung, Tse-Hua; Wang, Pi-Chung

    2012-01-01

    Patient monitoring systems are gaining their importance as the fast-growing global elderly population increases demands for caretaking. These systems use wireless technologies to transmit vital signs for medical evaluation. In a multihop ZigBee network, the existing systems usually use broadcast or multicast schemes to increase the reliability of signals transmission; however, both the schemes lead to significantly higher network traffic and end-to-end transmission delay. In this paper, we present a reliable transmission protocol based on anycast routing for wireless patient monitoring. Our scheme automatically selects the closest data receiver in an anycast group as a destination to reduce the transmission latency as well as the control overhead. The new protocol also shortens the latency of path recovery by initiating route recovery from the intermediate routers of the original path. On the basis of a reliable transmission scheme, we implement a ZigBee device for fall monitoring, which integrates fall detection, indoor positioning, and ECG monitoring. When the triaxial accelerometer of the device detects a fall, the current position of the patient is transmitted to an emergency center through a ZigBee network. In order to clarify the situation of the fallen patient, 4-s ECG signals are also transmitted. Our transmission scheme ensures the successful transmission of these critical messages. The experimental results show that our scheme is fast and reliable. We also demonstrate that our devices can seamlessly integrate with the next generation technology of wireless wide area network, worldwide interoperability for microwave access, to achieve real-time patient monitoring.

  6. Whirlpool routing for mobility

    KAUST Repository

    Lee, Jung Woo

    2010-01-01

    We present the Whirlpool Routing Protocol (WARP), which efficiently routes data to a node moving within a static mesh. The key insight in WARP\\'s design is that data traffic can use an existing routing gradient to efficiently probe the topology, repair the routing gradient, and communicate these repairs to nearby nodes. Using simulation, controlled testbeds, and real mobility experiments, we find that using the data plane for topology maintenance is highly effective due to the incremental nature of mobility updates. WARP leverages the fact that converging flows at a destination make the destination have the region of highest traffic. We provide a theoretical basis for WARP\\'s behavior, defining an "update area" in which the topology must adjust when a destination moves. As long as packets arrive at a destination before it moves outside of the update area, WARP can repair the topology using the data plane. Compared to existing protocols, such as DYMO and HYPER, WARP\\'s packet drop rate is up to 90% lower while sending up to 90% fewer packets.

  7. Routing Data Authentication in Wireless Networks; TOPICAL

    International Nuclear Information System (INIS)

    TORGERSON, MARK D.; VAN LEEUWEN, BRIAN P.

    2001-01-01

    In this paper, we discuss several specific threats directed at the routing data of an ad hoc network. We address security issues that arise from wrapping authentication mechanisms around ad hoc routing data. We show that this bolt-on approach to security may make certain attacks more difficult, but still leaves the network routing data vulnerable. We also show that under a certain adversarial model, most existing routing protocols cannot be secured with the aid of digital signatures

  8. Command and Control Data Dissemination Using IP Multicast

    National Research Council Canada - National Science Library

    Barrera, Raymond

    1999-01-01

    Tools have been developed which allow tactical data to be exchanged over Internet Protocol networks, but the quality of service necessary to operate these tools is not available for most Naval vessels at this time...

  9. Energy-Efficient Resource and Power Allocation for Underlay Multicast Device-to-Device Transmission

    Directory of Open Access Journals (Sweden)

    Fan Jiang

    2017-11-01

    Full Text Available In this paper, we present an energy-efficient resource allocation and power control scheme for D2D (Device-to-Device multicasting transmission. The objective is to maximize the overall energy-efficiency of D2D multicast clusters through effective resource allocation and power control schemes, while considering the quality of service (QoS requirements of both cellular users (CUs and D2D clusters. We first build the optimization model and a heuristic resource and power allocation algorithm is then proposed to solve the energy-efficiency problem with less computational complexity. Numerical results indicate that the proposed algorithm outperforms existing schemes in terms of throughput per energy consumption.

  10. Optimizing Energy and Modulation Selection in Multi-Resolution Modulation For Wireless Video Broadcast/Multicast

    KAUST Repository

    She, James

    2009-11-01

    Emerging technologies in Broadband Wireless Access (BWA) networks and video coding have enabled high-quality wireless video broadcast/multicast services in metropolitan areas. Joint source-channel coded wireless transmission, especially using hierarchical/superposition coded modulation at the channel, is recognized as an effective and scalable approach to increase the system scalability while tackling the multi-user channel diversity problem. The power allocation and modulation selection problem, however, is subject to a high computational complexity due to the nonlinear formulation and huge solution space. This paper introduces a dynamic programming framework with conditioned parsing, which significantly reduces the search space. The optimized result is further verified with experiments using real video content. The proposed approach effectively serves as a generalized and practical optimization framework that can gauge and optimize a scalable wireless video broadcast/multicast based on multi-resolution modulation in any BWA network.

  11. Optimizing Energy and Modulation Selection in Multi-Resolution Modulation For Wireless Video Broadcast/Multicast

    KAUST Repository

    She, James; Ho, Pin-Han; Shihada, Basem

    2009-01-01

    Emerging technologies in Broadband Wireless Access (BWA) networks and video coding have enabled high-quality wireless video broadcast/multicast services in metropolitan areas. Joint source-channel coded wireless transmission, especially using hierarchical/superposition coded modulation at the channel, is recognized as an effective and scalable approach to increase the system scalability while tackling the multi-user channel diversity problem. The power allocation and modulation selection problem, however, is subject to a high computational complexity due to the nonlinear formulation and huge solution space. This paper introduces a dynamic programming framework with conditioned parsing, which significantly reduces the search space. The optimized result is further verified with experiments using real video content. The proposed approach effectively serves as a generalized and practical optimization framework that can gauge and optimize a scalable wireless video broadcast/multicast based on multi-resolution modulation in any BWA network.

  12. End-to-End Mechanisms for Rate-Adaptive Multicast Streaming over the Internet

    OpenAIRE

    Rimac, Ivica

    2005-01-01

    Continuous media applications over packet-switched networks are becoming more and more popular. Radio stations, for example, already use streaming technology to disseminate their content to users on the Internet, and video streaming services are expected to experience similar popularity. In contrast to traditional television and radio broadcast systems, however, prevalent Internet streaming solutions are based on unicast communication and raise scalability and efficiency issues. Multicast com...

  13. Route Flap Damping Made Usable

    Science.gov (United States)

    Pelsser, Cristel; Maennel, Olaf; Mohapatra, Pradosh; Bush, Randy; Patel, Keyur

    The Border Gateway Protocol (BGP), the de facto inter-domain routing protocol of the Internet, is known to be noisy. The protocol has two main mechanisms to ameliorate this, MinRouteAdvertisementInterval (MRAI), and Route Flap Damping (RFD). MRAI deals with very short bursts on the order of a few to 30 seconds. RFD deals with longer bursts, minutes to hours. Unfortunately, RFD was found to severely penalize sites for being well-connected because topological richness amplifies the number of update messages exchanged. So most operators have disabled it. Through measurement, this paper explores the avenue of absolutely minimal change to code, and shows that a few RFD algorithmic constants and limits can be trivially modified, with the result being damping a non-trivial amount of long term churn without penalizing well-behaved prefixes' normal convergence process.

  14. One-to-six WDM multicasting of DPSK signals based on dual-pump four-wave mixing in a silicon waveguide

    DEFF Research Database (Denmark)

    Pu, Minhao; Hu, Hao; Ji, Hua

    2011-01-01

    We present WDM multicasting based on dual-pump four-wave mixing in a 3-mm long dispersion engineered silicon waveguide. One-to-six phase-preserving WDM multicasting of 10-Gb/s differential phase-shiftkeying (DPSK) data is experimentally demonstrated with bit-error rate measurements. All the six...

  15. Tunable Photonic RF Generator for Dynamic Allocation and Multicast of 1.25 Gbps Channels in the 60 GHz Unlicensed Band

    DEFF Research Database (Denmark)

    Lebedev, Alexander; Pang, Xiaodan; Vegas Olmos, Juan José

    2013-01-01

    ) or in the central office (CO). At the RN, we perform the replication of the original channel suitable for closely spaced multicast applications such as high definition (HD) video delivery where RN serves as a photonic radio frequency (RF) generator for both channel allocation and multicast. Experimental...

  16. Research on Innovating, Applying Multiple Paths Routing Technique Based on Fuzzy Logic and Genetic Algorithm for Routing Messages in Service - Oriented Routing

    Directory of Open Access Journals (Sweden)

    Nguyen Thanh Long

    2015-02-01

    Full Text Available MANET (short for Mobile Ad-Hoc Network consists of a set of mobile network nodes, network configuration changes very fast. In content based routing, data is transferred from source node to request nodes is not based on destination addresses. Therefore, it is very flexible and reliable, because source node does not need to know destination nodes. If We can find multiple paths that satisfies bandwidth requirement, split the original message into multiple smaller messages to transmit concurrently on these paths. On destination nodes, combine separated messages into the original message. Hence it can utilize better network resources, causes data transfer rate to be higher, load balancing, failover. Service Oriented Routing is inherited from the model of content based routing (CBR, combined with several advanced techniques such as Multicast, multiple path routing, Genetic algorithm to increase the data rate, and data encryption to ensure information security. Fuzzy logic is a logical field study evaluating the accuracy of the results based on the approximation of the components involved, make decisions based on many factors relative accuracy based on experimental or mathematical proof. This article presents some techniques to support multiple path routing from one network node to a set of nodes with guaranteed quality of service. By using these techniques can decrease the network load, congestion, use network resources efficiently.

  17. DESIGN OF ENERGY EFFICIENT ROUTING ALGORITHM FOR WIRELESS SENSOR NETWORK (WSN) USING PASCAL GRAPH

    OpenAIRE

    Deepali Panwar; Subhrendu Guha Neogi

    2013-01-01

    Development of energy efficient Wireless Sensor Network (WSN) routing protocol is nowadays main area of interest amongst researchers. This research is an effort in designing energy efficient Wireless Sensor Network (WSN) routing protocol under certain parameters consideration. Research report discusses various existing WSN routing protocols and propose a new WSN energy efficient routing protocol. Results show a significant improvement in life cycle of the nodes and enhancement ...

  18. Evaluación de ancho de banda en transmisiones multicast sparse mode implementadas en redes IPV6

    OpenAIRE

    Pineda Ancco, Ferdinand; Directora Asociada de Investigación, Universidad Peruana Unión. Lima; Cruz de la Cruz, José; Mamani Pari, David

    2017-01-01

    En el trabajo de investigación se describió el diseño e implementación del protocolo multicast de tipo Sparsemode con el objetivo de mejorar el tráfico de datos en redes que transporten información unidireccional. Eldiseño se realiza sobre una red que implementa IPV6 como protocolo de capa 3 del modelo de referencia OSI.Para validar el método, la evaluación del tráfico se realizó analizando el ancho de banda, retardos y cantidad debits enviados por el protocolo multicast Sparse mode cursado e...

  19. Scripted Mobile Network Routing in a Contested Environment

    National Research Council Canada - National Science Library

    Otto, Anthony R

    2008-01-01

    Mobile wireless network protocols currently run on optimistic routing algorithms, adjusting node connectivity only when the chosen connectivity metrics, such as signal strength, pass beyond minimum thresholds...

  20. Comparison of routing metrics for wireless mesh networks

    CSIR Research Space (South Africa)

    Nxumalo, SL

    2011-09-01

    Full Text Available in each and every relay node so as to find the next hop for the packet. A routing metric is simply a measure used for selecting the best path, used by a routing protocol. Figure 2 shows the relationship between a routing protocol and the routing... on its QoS-awareness level. The routing metrics that considered QoS the most were selected from each group. This section discusses the four routing metrics that were compared in this paper, which are: hop count (HOP), expected transmission count (ETX...

  1. Social-Aware Relay Selection for Cooperative Multicast Device-to-Device Communications

    Directory of Open Access Journals (Sweden)

    Francesco Chiti

    2017-12-01

    Full Text Available The increasing use of social networks such as Facebook, Twitter, and Instagram to share photos, video streaming, and music among friends has generated a huge increase in the amount of data traffic over wireless networks. This social behavior has triggered new communication paradigms such as device-to-device (D2D and relaying communication schemes, which are both considered as strong drivers for the next fifth-generation (5G cellular systems. Recently, the social-aware layer and its relationship to and influence on the physical communications layer have gained great attention as emerging focus points. We focus here on the case of relaying communications to pursue the multicast data dissemination to a group of users forming a social community through a relay node, according to the extension of the D2D mode to the case of device-to-many devices. Moreover, in our case, the source selects the device to act as the relay among different users of the multicast group by taking into account both the propagation link conditions and the relay social-trust level with the constraint of minimizing the end-to-end content delivery delay. An optimization procedure is also proposed in order to achieve the best performance. Finally, numerical results are provided to highlight the advantages of considering the impact of social level on the end-to-end delivery delay in the integrated social–physical network in comparison with the classical relay-assisted multicast communications for which the relay social-trust level is not considered.

  2. Real-time video streaming system for LHD experiment using IP multicast

    International Nuclear Information System (INIS)

    Emoto, Masahiko; Yamamoto, Takashi; Yoshida, Masanobu; Nagayama, Yoshio; Hasegawa, Makoto

    2009-01-01

    In order to accomplish smooth cooperation research, remote participation plays an important role. For this purpose, the authors have been developing various applications for remote participation for the LHD (Large Helical Device) experiments, such as Web interface for visualization of acquired data. The video streaming system is one of them. It is useful to grasp the status of the ongoing experiment remotely, and we provide the video images displayed in the control room to the remote users. However, usual streaming servers cannot send video images without delay. The delay changes depending on how to send the images, but even a little delay might become critical if the researchers use the images to adjust the diagnostic devices. One of the main causes of delay is the procedure of compressing and decompressing the images. Furthermore, commonly used video compression method is lossy; it removes less important information to reduce the size. However, lossy images cannot be used for physical analysis because the original information is lost. Therefore, video images for remote participation should be sent without compression in order to minimize the delay and to supply high quality images durable for physical analysis. However, sending uncompressed video images requires large network bandwidth. For example, sending 5 frames of 16bit color SXGA images a second requires 100Mbps. Furthermore, the video images must be sent to several remote sites simultaneously. It is hard for a server PC to handle such a large data. To cope with this problem, the authors adopted IP multicast to send video images to several remote sites at once. Because IP multicast packets are sent only to the network on which the clients want the data; the load of the server does not depend on the number of clients and the network load is reduced. In this paper, the authors discuss the feasibility of high bandwidth video streaming system using IP multicast. (author)

  3. Performance Evaluation of Multicast Video Distribution using LTE-A in Vehicular Environments

    OpenAIRE

    Thota, Jayashree; Bulut, Berna; Doufexi, Angela; Armour, Simon; Nix, Andrew

    2017-01-01

    Application Layer Forward Error Correction (AL-FEC) based on Raptor codes has been employed in Multimedia Broadcast/Multicast Services (MBMS) to improve reliability. This paper considers a cross-layer system based on the latest Raptor Q codes for transmitting high data rate video. Multiple Input Multiple Output (MIMO) channels in a realistic outdoor environment for a user moving at 50kmph in an LTE-A system is considered. A link adaptation model with optimized cross-layer parameters is propos...

  4. Hybrid ARQ Scheme with Autonomous Retransmission for Multicasting in Wireless Sensor Networks.

    Science.gov (United States)

    Jung, Young-Ho; Choi, Jihoon

    2017-02-25

    A new hybrid automatic repeat request (HARQ) scheme for multicast service for wireless sensor networks is proposed in this study. In the proposed algorithm, the HARQ operation is combined with an autonomous retransmission method that ensure a data packet is transmitted irrespective of whether or not the packet is successfully decoded at the receivers. The optimal number of autonomous retransmissions is determined to ensure maximum spectral efficiency, and a practical method that adjusts the number of autonomous retransmissions for realistic conditions is developed. Simulation results show that the proposed method achieves higher spectral efficiency than existing HARQ techniques.

  5. Hybrid ARQ Scheme with Autonomous Retransmission for Multicasting in Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Young-Ho Jung

    2017-02-01

    Full Text Available A new hybrid automatic repeat request (HARQ scheme for multicast service for wireless sensor networks is proposed in this study. In the proposed algorithm, the HARQ operation is combined with an autonomous retransmission method that ensure a data packet is transmitted irrespective of whether or not the packet is successfully decoded at the receivers. The optimal number of autonomous retransmissions is determined to ensure maximum spectral efficiency, and a practical method that adjusts the number of autonomous retransmissions for realistic conditions is developed. Simulation results show that the proposed method achieves higher spectral efficiency than existing HARQ techniques.

  6. Sinkhole Avoidance Routing in Wireless Sensor Networks

    Science.gov (United States)

    2011-05-09

    COVERED (From- To) 09-05-2011 4. TITLE AND SUBTITLE 5a. CONTRACT NUMBER Sinkhole Avoidance Routing in Wireless Sensor Networks 5b . GRANT NUMBER . 5c...reliability of wireless sensor networks. 15. SUBJECT TERMS wireless sensor networks, sinkhole attack, routing protocol 16. SECURITY CLASSIFICATION...Include area code) Standard Form 298 (Rev. 8/98) Prescribed by ANSI Std . Z39.18 1 Sinkhole Avoidance Routing in Wireless Sensor Networks MIDN 1/C

  7. Routing in Wireless Multimedia Home Networks

    NARCIS (Netherlands)

    Scholten, Johan; Jansen, P.G.; Hop, Laurens

    This paper describes an adapted version of the destination sequenced distance vector routing protocol (DSDV) which is suitable to calculate routes in a wireless real-time home network. The home network is based on a IEEE 802.11b ad hoc network and uses a scheduled token to enforce real-time

  8. Routing in Wireless Multimedia Home Networks

    NARCIS (Netherlands)

    Scholten, Johan; Jansen, P.G.; Hop, Laurens

    This paper describes an adapted version of the destination sequenced distance vector routing protocol (DSDV) which is suitable to calculate routes in a wireless ¿real-time¿ home network. The home network is based on a IEEE 802.11b ad hoc network and uses a scheduled token to enforce real-time

  9. Out-of-Sequence Prevention for Multicast Input-Queuing Space-Memory-Memory Clos-Network

    DEFF Research Database (Denmark)

    Yu, Hao; Ruepp, Sarah; Berger, Michael Stübert

    2011-01-01

    This paper proposes two cell dispatching algorithms for the input-queuing space-memory-memory (IQ-SMM) Closnetwork to reduce out-of-sequence (OOS) for multicast traffic. The frequent connection pattern change of DSRR results in a severe OOS problem. Based on the principle of DSRR, MFDSRR is able ...

  10. Energy Efficient MANET Routing Using a Combination of Span and BECA/AFECA

    DEFF Research Database (Denmark)

    Kristensen, Mads Darø; Bouvin, Niels Olof

    2008-01-01

    This paper presents some novel approaches for energy efficient routing in mobile ad-hoc networks. Two known energy preserving techniques, Span and BECA/AFECA, are combined with a well-known re-active routing protocol, AODV, to create a new energy efficient routing protocol. Furthermore, the proto......This paper presents some novel approaches for energy efficient routing in mobile ad-hoc networks. Two known energy preserving techniques, Span and BECA/AFECA, are combined with a well-known re-active routing protocol, AODV, to create a new energy efficient routing protocol. Furthermore...

  11. Load Balancing Routing with Bounded Stretch

    Directory of Open Access Journals (Sweden)

    Chen Siyuan

    2010-01-01

    Full Text Available Routing in wireless networks has been heavily studied in the last decade. Many routing protocols are based on classic shortest path algorithms. However, shortest path-based routing protocols suffer from uneven load distribution in the network, such as crowed center effect where the center nodes have more load than the nodes in the periphery. Aiming to balance the load, we propose a novel routing method, called Circular Sailing Routing (CSR, which can distribute the traffic more evenly in the network. The proposed method first maps the network onto a sphere via a simple stereographic projection, and then the route decision is made by a newly defined "circular distance" on the sphere instead of the Euclidean distance in the plane. We theoretically prove that for a network, the distance traveled by the packets using CSR is no more than a small constant factor of the minimum (the distance of the shortest path. We also extend CSR to a localized version, Localized CSR, by modifying greedy routing without any additional communication overhead. In addition, we investigate how to design CSR routing for 3D networks. For all proposed methods, we conduct extensive simulations to study their performances and compare them with global shortest path routing or greedy routing in 2D and 3D wireless networks.

  12. The intergroup protocols: Scalable group communication for the internet

    Energy Technology Data Exchange (ETDEWEB)

    Berket, Karlo [Univ. of California, Santa Barbara, CA (United States)

    2000-12-04

    Reliable group ordered delivery of multicast messages in a distributed system is a useful service that simplifies the programming of distributed applications. Such a service helps to maintain the consistency of replicated information and to coordinate the activities of the various processes. With the increasing popularity of the Internet, there is an increasing interest in scaling the protocols that provide this service to the environment of the Internet. The InterGroup protocol suite, described in this dissertation, provides such a service, and is intended for the environment of the Internet with scalability to large numbers of nodes and high latency links. The InterGroup protocols approach the scalability problem from various directions. They redefine the meaning of group membership, allow voluntary membership changes, add a receiver-oriented selection of delivery guarantees that permits heterogeneity of the receiver set, and provide a scalable reliability service. The InterGroup system comprises several components, executing at various sites within the system. Each component provides part of the services necessary to implement a group communication system for the wide-area. The components can be categorized as: (1) control hierarchy, (2) reliable multicast, (3) message distribution and delivery, and (4) process group membership. We have implemented a prototype of the InterGroup protocols in Java, and have tested the system performance in both local-area and wide-area networks.

  13. Robust against route failure using power proficient reliable routing in MANET

    Directory of Open Access Journals (Sweden)

    M. Malathi

    2018-03-01

    Full Text Available The aim of this paper was to propose a novel routing protocol for Mobile Adhoc Network communication which reduces the route failure during transmission. The proposed routing protocol uses 3 salient parameters to discover the path which ensure the reliable communication. The quality of the channel, link quality and energy level of the node are the major reasons for unintentional node failure in mobile Adhoc network. So the proposed routing protocol considers these three parameters to select the best forwarder node in the path. The reliable data communication is achieved by transmitting data via path selected by the proposed routing scheme has been proven using network simulator (NS2. Keywords: Channel quality, Link quality, Mobile Adhoc Network (MANET, Residual energy

  14. Adaptive Probabilistic Routing in Wireless Ad Hoc Networks

    OpenAIRE

    Hasan, Affaf; Liaqat, Ismail

    2013-01-01

    The goal of this thesis work is to analyze how design elements and wireless attributes affect opportunistic routing, and in this context develop a new protocol. The algorithm developed aims to improve opportunistic elements in comparison to a well-known opportunistic protocol Simple Opportunistic Adaptive Routing (SOAR).

  15. A Machine Learning Concept for DTN Routing

    Science.gov (United States)

    Dudukovich, Rachel; Hylton, Alan; Papachristou, Christos

    2017-01-01

    This paper discusses the concept and architecture of a machine learning based router for delay tolerant space networks. The techniques of reinforcement learning and Bayesian learning are used to supplement the routing decisions of the popular Contact Graph Routing algorithm. An introduction to the concepts of Contact Graph Routing, Q-routing and Naive Bayes classification are given. The development of an architecture for a cross-layer feedback framework for DTN (Delay-Tolerant Networking) protocols is discussed. Finally, initial simulation setup and results are given.

  16. Design and simulation analysis of non-receiver aware and receiver ...

    African Journals Online (AJOL)

    We present multicast extensions to our recently proposed Location Prediction Based Routing (LPBR) protocol, referred to as NR-MLPBR and R-MLPBR, to simultaneously reduce the number of multicast tree discoveries and number of links per tree and/or the hop count per source-receiver path in mobile ad hoc networks ...

  17. Next Generation Network Routing and Control Plane

    DEFF Research Database (Denmark)

    Fu, Rong

    proved, the dominating Border Gateway Protocol (BGP) cannot address all the issues that in inter-domain QoS routing. Thus a new protocol or network architecture has to be developed to be able to carry the inter-domain traffic with the QoS and TE consideration. Moreover, the current network control also...... lacks the ability to cooperate between different domains and operators. The emergence of label switching transport technology such as of Multi-Protocol Label Switching (MPLS) or Generalized MPLS (GMPLS) supports the traffic transport in a finer granularity and more dedicated end-to-end Quality...... (RACF) provides the platform that enables cooperation and ubiquitous integration between networks. In this paper, we investigate in the network architecture, protocols and algorithms for inter-domain QoS routing and traffic engineering. The PCE based inter-domain routing architecture is enhanced...

  18. ASSESSMENT OF RIP-V1 AND OSPF-V2 PROTOCOL WITH CONSIDERATION OF CONVERGENCE CRITERIA AND SENDING PROTOCOLS TRAFFIC

    Directory of Open Access Journals (Sweden)

    Hamed Jelodar

    2014-03-01

    Full Text Available Routing Protocols are underlying principles in networks like internet, transport and mobile. Routing Protocols include a series of rules and algorithms that consider routing metric and select the best way for sending healthy data packets from origin to destination. Dynamic routing protocol compatible to topology has a changeable state. RIP and OSPF are dynamic routing protocol that we consider criteria like convergence and sending protocols traffic assessment RIP first version and OSPF second version. By the test we have done on OPNET stimulation we understood that the OSPF protocol was more efficient than RIP protocol.

  19. Satellite Communications Using Commercial Protocols

    Science.gov (United States)

    Ivancic, William D.; Griner, James H.; Dimond, Robert; Frantz, Brian D.; Kachmar, Brian; Shell, Dan

    2000-01-01

    NASA Glenn Research Center has been working with industry, academia, and other government agencies in assessing commercial communications protocols for satellite and space-based applications. In addition, NASA Glenn has been developing and advocating new satellite-friendly modifications to existing communications protocol standards. This paper summarizes recent research into the applicability of various commercial standard protocols for use over satellite and space- based communications networks as well as expectations for future protocol development. It serves as a reference point from which the detailed work can be readily accessed. Areas that will be addressed include asynchronous-transfer-mode quality of service; completed and ongoing work of the Internet Engineering Task Force; data-link-layer protocol development for unidirectional link routing; and protocols for aeronautical applications, including mobile Internet protocol routing for wireless/mobile hosts and the aeronautical telecommunications network protocol.

  20. Multicast Services of QoS-Aware Active Queue Management over IP Multimedia Applications

    Science.gov (United States)

    Hwang, I.-Shyan; Hwang, Bor-Jiunn; Chang, Pen-Ming

    2010-10-01

    Recently, the multimedia services such as IPTV, video conference emerges to be the main traffic source. When UDP coexists with TCP, it induces not only congestion collapse but also unfairness problem. In this paper, a new Active Queue Management (AQM) algorithm, called Traffic Sensitive Active Queue Management (TSAQM), is proposed for providing multimedia services. The TSAQM comprise Dynamic Weight Allocate Scheme (DWAS) and Service Guarantee Scheme (SGS), the purpose of DWAS is to allocate resource with fairness and high end-user utility, and the purpose of SGS is to determine the satisfactory threshold (TH) and threshold region (TR). Several objectives of this proposed scheme include achieving high end-user utility for video service, considering the multicast as well as unicast proprieties to meet inter-class fairness and achieving the QoS requirement by adjusting the thresholds adaptively based on traffic situations.

  1. Dynamic Programming Optimization of Multi-rate Multicast Video-Streaming Services

    Directory of Open Access Journals (Sweden)

    Nestor Michael Caños Tiglao

    2010-06-01

    Full Text Available In large scale IP Television (IPTV and Mobile TV distributions, the video signal is typically encoded and transmitted using several quality streams, over IP Multicast channels, to several groups of receivers, which are classified in terms of their reception rate. As the number of video streams is usually constrained by both the number of TV channels and the maximum capacity of the content distribution network, it is necessary to find the selection of video stream transmission rates that maximizes the overall user satisfaction. In order to efficiently solve this problem, this paper proposes the Dynamic Programming Multi-rate Optimization (DPMO algorithm. The latter was comparatively evaluated considering several user distributions, featuring different access rate patterns. The experimental results reveal that DPMO is significantly more efficient than exhaustive search, while presenting slightly higher execution times than the non-optimal Multi-rate Step Search (MSS algorithm.

  2. Admission and Preventive Load Control for Delivery of Multicast and Broadcast Services via S-UMTS

    Science.gov (United States)

    Angelou, E.; Koutsokeras, N.; Andrikopoulos, I.; Mertzanis, I.; Karaliopoulos, M.; Henrio, P.

    2003-07-01

    An Admission Control strategy is proposed for unidirectional satellite systems delivering multicast and broadcast services to mobile users. In such systems, both the radio interface and the targeted services impose particular requirements on the RRM task. We briefly discuss the RRM requirements that stem from the services point of view and from the features of the SATIN access scheme that differentiate it from the conventional T-UMTS radio interface. The main functional entities of RRM and the alternative modes of operation are outlined and the proposed Admission Control algorithm is described in detail. The results from the simulation study that demonstrate its performance for a number of different scenarios are finally presented and conclusions derived.

  3. Energy Effective Congestion Control for Multicast with Network Coding in Wireless Ad Hoc Network

    Directory of Open Access Journals (Sweden)

    Chuanxin Zhao

    2014-01-01

    Full Text Available In order to improve network throughput and reduce energy consumption, we propose in this paper a cross-layer optimization design that is able to achieve multicast utility maximization and energy consumption minimization. The joint optimization of congestion control and power allocation is formulated to be a nonlinear nonconvex problem. Using dual decomposition, a distributed optimization algorithm is proposed to avoid the congestion by control flow rate at the source node and eliminate the bottleneck by allocating the power at the intermediate node. Simulation results show that the cross-layer algorithm can increase network performance, reduce the energy consumption of wireless nodes and prolong the network lifetime, while keeping network throughput basically unchanged.

  4. Joint Power Allocation for Multicast Systems with Physical-Layer Network Coding

    Directory of Open Access Journals (Sweden)

    Zhu Wei-Ping

    2010-01-01

    Full Text Available This paper addresses the joint power allocation issue in physical-layer network coding (PLNC of multicast systems with two sources and two destinations communicating via a large number of distributed relays. By maximizing the achievable system rate, a constrained optimization problem is first formulated to jointly allocate powers for the source and relay terminals. Due to the nonconvex nature of the cost function, an iterative algorithm with guaranteed convergence is developed to solve the joint power allocation problem. As an alternative, an upper bound of the achievable rate is also derived to modify the original cost function in order to obtain a convex optimization solution. This approximation is shown to be asymptotically optimal in the sense of maximizing the achievable rate. It is confirmed through Monte Carlo simulations that the proposed joint power allocation schemes are superior to the existing schemes in terms of achievable rate and cumulative distribution function (CDF.

  5. Network-topology-adaptive quantum conference protocols

    International Nuclear Information System (INIS)

    Zhang Sheng; Wang Jian; Tang Chao-Jing; Zhang Quan

    2011-01-01

    As an important application of the quantum network communication, quantum multiparty conference has made multiparty secret communication possible. Previous quantum multiparty conference schemes based on quantum data encryption are insensitive to network topology. However, the topology of the quantum network significantly affects the communication efficiency, e.g., parallel transmission in a channel with limited bandwidth. We have proposed two distinctive protocols, which work in two basic network topologies with efficiency higher than the existing ones. We first present a protocol which works in the reticulate network using Greeberger—Horne—Zeilinger states and entanglement swapping. Another protocol, based on quantum multicasting with quantum data compression, which can improve the efficiency of the network, works in the star-like network. The security of our protocols is guaranteed by quantum key distribution and one-time-pad encryption. In general, the two protocols can be applied to any quantum network where the topology can be equivalently transformed to one of the two structures we propose in our protocols. (general)

  6. Efficiency Intra-Cluster Device-to-Device Relay Selection for Multicast Services Based on Combinatorial Auction

    Directory of Open Access Journals (Sweden)

    Yong Zhang

    2015-12-01

    Full Text Available In Long Term Evolution-Advanced (LTE-A networks, Device-to-device (D2D communications can be utilized to enhance the performance of multicast services by leveraging D2D relays to serve nodes with worse channel conditions within a cluster. For traditional D2D relay schemes, D2D links with poor channel condition may be the bottleneck of system sum data rate. In this paper, to optimize the throughput of D2D communications, we introduce an iterative combinatorial auction algorithm for efficient D2D relay selection. In combinatorial auctions, the User Equipments (UEs that fails to correctly receive multicast data from eNodeB (eNB are viewed as bidders that compete for D2D relays, while the eNB is treated as the auctioneer. We also give properties of convergency and low-complexity and present numerical simulations to verify the efficiency of the proposed algorithm.

  7. A Low-Complexity Subgroup Formation with QoS-Aware for Enhancing Multicast Services in LTE Networks

    Science.gov (United States)

    Algharem, M.; Omar, M. H.; Rahmat, R. F.; Budiarto, R.

    2018-03-01

    The high demand of Multimedia services on in Long Term Evolution (LTE) and beyond networks forces the networks operators to find a solution that can handle the huge traffic. Along with this, subgroup formation techniques are introduced to overcome the limitations of the Conventional Multicast Scheme (CMS) by splitting the multicast users into several subgroups based on the users’ channels quality signal. However, finding the best subgroup configuration with low complexity is need more investigations. In this paper, an efficient and simple subgroup formation mechanisms are proposed. The proposed mechanisms take the transmitter MAC queue in account. The effectiveness of the proposed mechanisms is evaluated and compared with CMS in terms of throughput, fairness, delay, Block Error Rate (BLER).

  8. Hurricane Evacuation Routes

    Data.gov (United States)

    Department of Homeland Security — Hurricane Evacuation Routes in the United States A hurricane evacuation route is a designated route used to direct traffic inland in case of a hurricane threat. This...

  9. A Preemptive Link State Spanning Tree Source Routing Scheme for Opportunistic Data Forwarding in MANET

    OpenAIRE

    R. Poonkuzhali; M. Y. Sanavullah; A. Sabari

    2014-01-01

    Opportunistic Data Forwarding (ODF) has drawn much attention in mobile adhoc networking research in recent years. The effectiveness of ODF in MANET depends on a suitable routing protocol which provides a powerful source routing services. PLSR is featured by source routing, loop free and small routing overhead. The update messages in PLSR are integrated into a tree structure and no need to time stamp routing updates which reduces the routing overhead.

  10. Multi-Objective Resource Allocation Scheme for D2D Multicast with QoS Guarantees in Cellular Networks

    Directory of Open Access Journals (Sweden)

    Fangmin Li

    2016-09-01

    Full Text Available Device-to-device (D2D multicast communication can greatly improve the spectrum utilization in a content delivery scenario. However, the co-channel interference and power consumption brought by D2D bring new challenges. All the D2D multicast groups expect to achieve a higher system capacity with less extra energy cost. In this paper, we investigate the uplink resource allocation issue when D2D multicast groups share the resources with other cellular uses (CUs, while guaranteeing a certain level of quality of service (QoS to CUs and D2D users. Firstly we address a flexible tradeoff framework in which the system power consumption and the system capacity (i.e., the number of admitted D2D links are assigned with different weight factors so that these two objectives are jointly considered. Then we propose an efficient resource optimization scheme, which comprises sub-channel allocation and signal-to-interference- plus-noise ratio (SINR assignment. Numerical results validate the effectiveness of the proposed framework, and demonstrate the advantages in dealing with the proposed multi-objective optimization problem.

  11. Hybrid digital-analog video transmission in wireless multicast and multiple-input multiple-output system

    Science.gov (United States)

    Liu, Yu; Lin, Xiaocheng; Fan, Nianfei; Zhang, Lin

    2016-01-01

    Wireless video multicast has become one of the key technologies in wireless applications. But the main challenge of conventional wireless video multicast, i.e., the cliff effect, remains unsolved. To overcome the cliff effect, a hybrid digital-analog (HDA) video transmission framework based on SoftCast, which transmits the digital bitstream with the quantization residuals, is proposed. With an effective power allocation algorithm and appropriate parameter settings, the residual gains can be maximized; meanwhile, the digital bitstream can assure transmission of a basic video to the multicast receiver group. In the multiple-input multiple-output (MIMO) system, since nonuniform noise interference on different antennas can be regarded as the cliff effect problem, ParCast, which is a variation of SoftCast, is also applied to video transmission to solve it. The HDA scheme with corresponding power allocation algorithms is also applied to improve video performance. Simulations show that the proposed HDA scheme can overcome the cliff effect completely with the transmission of residuals. What is more, it outperforms the compared WSVC scheme by more than 2 dB when transmitting under the same bandwidth, and it can further improve performance by nearly 8 dB in MIMO when compared with the ParCast scheme.

  12. A Lightweight Protocol for Secure Video Streaming.

    Science.gov (United States)

    Venčkauskas, Algimantas; Morkevicius, Nerijus; Bagdonas, Kazimieras; Damaševičius, Robertas; Maskeliūnas, Rytis

    2018-05-14

    The Internet of Things (IoT) introduces many new challenges which cannot be solved using traditional cloud and host computing models. A new architecture known as fog computing is emerging to address these technological and security gaps. Traditional security paradigms focused on providing perimeter-based protections and client/server point to point protocols (e.g., Transport Layer Security (TLS)) are no longer the best choices for addressing new security challenges in fog computing end devices, where energy and computational resources are limited. In this paper, we present a lightweight secure streaming protocol for the fog computing "Fog Node-End Device" layer. This protocol is lightweight, connectionless, supports broadcast and multicast operations, and is able to provide data source authentication, data integrity, and confidentiality. The protocol is based on simple and energy efficient cryptographic methods, such as Hash Message Authentication Codes (HMAC) and symmetrical ciphers, and uses modified User Datagram Protocol (UDP) packets to embed authentication data into streaming data. Data redundancy could be added to improve reliability in lossy networks. The experimental results summarized in this paper confirm that the proposed method efficiently uses energy and computational resources and at the same time provides security properties on par with the Datagram TLS (DTLS) standard.

  13. An Application of Path Sharing To Routing For Mobile Sinks In ...

    African Journals Online (AJOL)

    CODEXT protocol for optimizing routing to multiple sinks through reinforcement learning. Such a routing situation arises in WSNs with multiple, possibly mobile sinks, such as WSNs with actuators deployed in parallel to sensors. This protocol is based on GAF protocol and grid structure to reduce energy consumed.

  14. Applied Multiprotocol Routing in IP Telephony

    Directory of Open Access Journals (Sweden)

    Miroslav Voznak

    2010-01-01

    Full Text Available The aim of the project was to create a multi-protocol system using SIP, H.323 and MGCP standards, which would ensure routing to various types of VoIP networks. The priority was to provide multi-protocol support to SIP and H.323 signalling and the support of the routing using the ENUM standard which has recently passed from the trial phase into full operation in the Czech Republic. The document describes the system's architecture and the components used. It also briefly describes ENUM.

  15. OSPF-TE Extensions for Green Routing in Optical Networks

    DEFF Research Database (Denmark)

    Wang, Jiayuan; Ricciardi, S.; Fagertun, Anna Manolova

    2012-01-01

    This paper proposes extensions to the OSPF-TE protocol to enable green routing in GMPLS-controlled optical networks. Simulation results show a remarkable reduction in CO2 emissions by preferring network elements powered by green energy sources in the connection routing.......This paper proposes extensions to the OSPF-TE protocol to enable green routing in GMPLS-controlled optical networks. Simulation results show a remarkable reduction in CO2 emissions by preferring network elements powered by green energy sources in the connection routing....

  16. Routing architecture and security for airborne networks

    Science.gov (United States)

    Deng, Hongmei; Xie, Peng; Li, Jason; Xu, Roger; Levy, Renato

    2009-05-01

    Airborne networks are envisioned to provide interconnectivity for terrestial and space networks by interconnecting highly mobile airborne platforms. A number of military applications are expected to be used by the operator, and all these applications require proper routing security support to establish correct route between communicating platforms in a timely manner. As airborne networks somewhat different from traditional wired and wireless networks (e.g., Internet, LAN, WLAN, MANET, etc), security aspects valid in these networks are not fully applicable to airborne networks. Designing an efficient security scheme to protect airborne networks is confronted with new requirements. In this paper, we first identify a candidate routing architecture, which works as an underlying structure for our proposed security scheme. And then we investigate the vulnerabilities and attack models against routing protocols in airborne networks. Based on these studies, we propose an integrated security solution to address routing security issues in airborne networks.

  17. Research on routing algorithm based on the VANET

    Directory of Open Access Journals (Sweden)

    AN Li

    2016-01-01

    Full Text Available For the characteristics of high speed mobility of nodes, frequent changes of dynamic topology and frequent interrupts of the communication links in the VANET, this paper analyzed the defect of the current mobile ad-hoc network routing protocol, and carried on the simulation analysis on the adaptability of AODV, DSR and DSDV routing protocols in VANET applications in the VANET. Through the above research, this paper obtained the conclusion that the AODV routing protocol is more suitable for vehicular ad hoc network environment

  18. Link reliability based hybrid routing for tactical mobile ad hoc network

    Institute of Scientific and Technical Information of China (English)

    Xie Xiaochuan; Wei Gang; Wu Keping; Wang Gang; Jia Shilou

    2008-01-01

    Tactical mobile ad hoc network (MANET) is a collection of mobile nodes forming a temporary network,without the aid of pre-established network infrastructure. The routing protocol has a crucial impact on the networkperformance in battlefields. Link reliability based hybrid routing (LRHR) is proposed, which is a novel hybrid routing protocol, for tactical MANET. Contrary to the traditional single path routing strategy, multiple paths are established between a pair of source-destination nodes. In the hybrid routing strategy, the rate of topological change provides a natural mechanism for switching dynamically between table-driven and on-demand routing. The simulation results indicate that the performances of the protocol in packet delivery ratio, routing overhead, and average end-to-end delay are better than the conventional routing protocol.

  19. VINE ROUTES IN BULGARIA

    Directory of Open Access Journals (Sweden)

    Lyuben Hristov

    2015-03-01

    Full Text Available The article deals with a scheme for the modern vine route in Bulgaria. Five basic vine routes and one international, between Bulgaria, Macedonia and Greece are defined. All routes consider characteristic varieties of grapes and kinds of vine products. Vine tourist products combined with visits of important natural and anthropological object are in the bases of the defined routes. The described routes are an important contribution to development of alternative tourist products in the country.

  20. Mobility Tolerant Firework Routing for Improving Reachability in MANETs

    Directory of Open Access Journals (Sweden)

    Gen Motoyoshi

    2014-03-01

    Full Text Available In this paper, we investigate our mobility-assisted and adaptive broadcast routing mechanism, called Mobility Tolerant Firework Routing (MTFR, which utilizes the concept of potentials for routing and improves node reachability, especially in situations with high mobility, by including a broadcast mechanism. We perform detailed evaluations by simulations in a mobile environment and demonstrate the advantages of MTFR over conventional potential-based routing. In particular, we show that MTFR produces better reachability in many aspects at the expense of a small additional transmission delay and intermediate traffic overhead, making MTFR a promising routing protocol and feasible for future mobile Internet infrastructures.

  1. Routing in opportunistic networks

    CERN Document Server

    Dhurandher, Sanjay; Anpalagan, Alagan; Vasilakos, Athanasios

    2013-01-01

    This book provides a comprehensive guide to selected topics, both ongoing and emerging, in routing in OppNets. The book is edited by worldwide technical leaders, prolific researchers and outstanding academics, Dr. Isaac Woungang and co-editors, Dr. Sanjay Kumar Dhurandher, Prof. Alagan Anpalagan and Prof. Athanasios Vasilakos. Consisting of contributions from well known and high profile researchers and scientists in their respective specialties, the main topics that are covered in this book include mobility and routing, social-aware routing, context-based routing, energy-aware routing, incentive-aware routing, stochastic routing, modeling of intermittent connectivity, in both infrastructure and infrastructure-less OppNets. Key Features: Discusses existing and emerging techniques for routing in infrastructure and infrastructure-less OppNets. Provides a unified covering of otherwise disperse selected topics on routing in infrastructure and infrastructure-less OppNets.  Includes a set of PowerPoint slides and g...

  2. Optimal Caching in Multicast 5G Networks with Opportunistic Spectrum Access

    KAUST Repository

    Emara, Mostafa

    2018-01-15

    Cache-enabled small base station (SBS) densification is foreseen as a key component of 5G cellular networks. This architecture enables storing popular files at the network edge (i.e., SBS caches), which empowers local communication and alleviates traffic congestions at the core/backhaul network. This paper develops a mathematical framework, based on stochastic geometry, to characterize the hit probability of a cache-enabled multicast 5G network with SBS multi-channel capabilities and opportunistic spectrum access. To this end, we first derive the hit probability by characterizing opportunistic spectrum access success probabilities, service distance distributions, and coverage probabilities. The optimal caching distribution to maximize the hit probability is then computed. The performance and trade-offs of the derived optimal caching distributions are then assessed and compared with two widely employed caching distribution schemes, namely uniform and Zipf caching, through numerical results and extensive simulations. It is shown that the Zipf caching almost optimal only in scenarios with large number of available channels and large cache sizes.

  3. Simulation and Evaluation of CTP and Secure-CTP Protocols

    Directory of Open Access Journals (Sweden)

    P. Pecho

    2010-04-01

    Full Text Available The paper discusses characteristics and qualities of two routing protocols – Collection Tree Protocol and its secure modification. The original protocol, as well as other protocols for wireless sensors, solves only problems of ra- dio communication and limited resources. Our design of the secure protocol tries to solve also the essential security ob- jectives. For the evaluation of properties of our protocol in large networks, a TOSSIM simulator was used. Our effort was to show the influence of the modification of the routing protocol to its behavior and quality of routing trees. We have proved that adding security into protocol design does not necessarily mean higher demands for data transfer, power consumption or worse protocol efficiency. In the paper, we manifest that security in the protocol may be achieved with low cost and may offer similar performance as the original protocol.

  4. The QKD network: model and routing scheme

    Science.gov (United States)

    Yang, Chao; Zhang, Hongqi; Su, Jinhai

    2017-11-01

    Quantum key distribution (QKD) technology can establish unconditional secure keys between two communicating parties. Although this technology has some inherent constraints, such as the distance and point-to-point mode limits, building a QKD network with multiple point-to-point QKD devices can overcome these constraints. Considering the development level of current technology, the trust relaying QKD network is the first choice to build a practical QKD network. However, the previous research didn't address a routing method on the trust relaying QKD network in detail. This paper focuses on the routing issues, builds a model of the trust relaying QKD network for easily analysing and understanding this network, and proposes a dynamical routing scheme for this network. From the viewpoint of designing a dynamical routing scheme in classical network, the proposed scheme consists of three components: a Hello protocol helping share the network topology information, a routing algorithm to select a set of suitable paths and establish the routing table and a link state update mechanism helping keep the routing table newly. Experiments and evaluation demonstrates the validity and effectiveness of the proposed routing scheme.

  5. A novel insight into beaconless geo-routing

    KAUST Repository

    Bader, Ahmed; Abed-Meraim, Karim; Alouini, Mohamed-Slim

    2012-01-01

    Beaconless geo-routing protocols have been traditionally analyzed assuming equal communication ranges for the data and control packets. This is not true in reality, since the communication range is in practice function of the packet length. As a

  6. Analisa Perbandingan Quality Of Service (QoS) pada Jaringan Backbone Non-MPLS dengan Jaringan Backbone MPLS Menggunakan Routing Protocol OSPF di PT. Telekomunikasi Indonesia, Tbk. Witel Ridar Riau

    OpenAIRE

    Silaban, Nestor Hasudungan; Sari, Linna Oktaviana; Anhar, Anhar

    2015-01-01

    The development of telecommunications technology based on Internet Protocol (IP) is now growing with the competitiveness of the telecommunications company to improve the quality of service to consumers. It can be obtained by increasing the quality backbone network using Multi Protocol Label Switching (MPLS). MPLS is a new technology to forward the packet to the backbone network without changing the existing network structure. The main idea is to construct a replacement MPLS paths using label ...

  7. Efficient Routing in Wireless Sensor Networks with Multiple Sessions

    OpenAIRE

    Dianjie Lu; Guijuan Zhang; Ren Han; Xiangwei Zheng; Hong Liu

    2014-01-01

    Wireless Sensor Networks (WSNs) are subject to node failures because of limited energy and link unreliability which makes the design of routing protocols in such networks a challenging task. The multipath routing scheme is an optimal alternative to address this problem which splits the traffic across multiple paths instead of routing all the traffic along a single path. However, using more paths introduces more contentions which degrade energy efficiency. The problem becomes even more difficu...

  8. Efficient File Sharing by Multicast - P2P Protocol Using Network Coding and Rank Based Peer Selection

    Science.gov (United States)

    Stoenescu, Tudor M.; Woo, Simon S.

    2009-01-01

    In this work, we consider information dissemination and sharing in a distributed peer-to-peer (P2P highly dynamic communication network. In particular, we explore a network coding technique for transmission and a rank based peer selection method for network formation. The combined approach has been shown to improve information sharing and delivery to all users when considering the challenges imposed by the space network environments.

  9. Hazmat Routes (National)

    Data.gov (United States)

    Department of Transportation — The Federal Motor Carrier Safety Administration (FMCSA) Hazardous Material Routes (NTAD) were developed using the 2004 First Edition TIGER/Line files. The routes are...

  10. State alternative route designations

    International Nuclear Information System (INIS)

    1989-07-01

    Pursuant to the Hazardous Materials Transportation Act (HMTA), the Department of Transportation (DOT) has promulgated a comprehensive set of regulations regarding the highway transportation of high-level radioactive materials. These regulations, under HM-164 and HM-164A, establish interstate highways as the preferred routes for the transportation of radioactive materials within and through the states. The regulations also provide a methodology by which a state may select alternative routes. First,the state must establish a ''state routing agency,'' defined as an entity authorized to use the state legal process to impose routing requirements on carriers of radioactive material (49 CFR 171.8). Once identified, the state routing agency must select routes in accordance with Large Quantity Shipments of Radioactive Materials or an equivalent routing analysis. Adjoining states and localities should be consulted on the impact of proposed alternative routes as a prerequisite of final route selection. Lastly, the states must provide written notice of DOT of any alternative route designation before the routes are deemed effective

  11. All-optical multi-wavelength conversion with negative power penalty by a commercial SOA-MZI for WDM wavelength multicast

    NARCIS (Netherlands)

    Yan, N.; Jung, H.D.; Tafur Monroy, I.; Waardt, de H.; Koonen, A.M.J.

    2007-01-01

    WDM wavelength multicast is demonstrated by all-optical multi-wavelength conversion at 10 Gb/s using a commercial SOA-MZI. We report for the first time simultaneous one-to-four conversion with negative power penalty of 1.84 dB.

  12. Development of a real-time monitoring system and integration of different computer system in LHD experiments using IP multicast

    International Nuclear Information System (INIS)

    Emoto, Masahiko; Nakamura, Yukio; Teramachi, Yasuaki; Okumura, Haruhiko; Yamaguchi, Satarou

    2002-01-01

    There are several different computer systems in LHD (Large Helical Device) experiment, and therefore the coalition of these computers is a key to perform the experiment. Real-time monitoring system is also important because the long discharge is needed in the LHD experiment. In order to achieve these two requirements, the technique of IP multicast is adopted. The authors have developed three new systems, the first one is the real-time monitoring system, the next one is the delivery system of the shot number and the last one is the real-time notification system of the plasma data registration. The first system can deliver the real-time monitoring data to the LHD experimental LAN through the firewall of the LHD control LAN in NIFS. The other two systems are used to realize high coalition of the different computers in the LHD plasma experiment. We can conclude that IP multicast is very useful both in the LHD experiment and a future large plasma experiment from various experiences. (author)

  13. Hybrid monitoring scheme for end-to-end performance enhancement of multicast-based real-time media

    Science.gov (United States)

    Park, Ju-Won; Kim, JongWon

    2004-10-01

    As real-time media applications based on IP multicast networks spread widely, end-to-end QoS (quality of service) provisioning for these applications have become very important. To guarantee the end-to-end QoS of multi-party media applications, it is essential to monitor the time-varying status of both network metrics (i.e., delay, jitter and loss) and system metrics (i.e., CPU and memory utilization). In this paper, targeting the multicast-enabled AG (Access Grid) a next-generation group collaboration tool based on multi-party media services, the applicability of hybrid monitoring scheme that combines active and passive monitoring is investigated. The active monitoring measures network-layer metrics (i.e., network condition) with probe packets while the passive monitoring checks both application-layer metrics (i.e., user traffic condition by analyzing RTCP packets) and system metrics. By comparing these hybrid results, we attempt to pinpoint the causes of performance degradation and explore corresponding reactions to improve the end-to-end performance. The experimental results show that the proposed hybrid monitoring can provide useful information to coordinate the performance improvement of multi-party real-time media applications.

  14. ZERO: Probabilistic Routing for Deploy and Forget Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Jose Carlos Pacho

    2010-09-01

    Full Text Available As Wireless Sensor Networks are being adopted by industry and agriculture for large-scale and unattended deployments, the need for reliable and energy-conservative protocols become critical. Physical and Link layer efforts for energy conservation are not mostly considered by routing protocols that put their efforts on maintaining reliability and throughput. Gradient-based routing protocols route data through most reliable links aiming to ensure 99% packet delivery. However, they suffer from the so-called ”hot spot” problem. Most reliable routes waste their energy fast, thus partitioning the network and reducing the area monitored. To cope with this ”hot spot” problem we propose ZERO a combined approach at Network and Link layers to increase network lifespan while conserving reliability levels by means of probabilistic load balancing techniques.

  15. Eco-sustainable routing in optical networks

    DEFF Research Database (Denmark)

    Ricciardi, Sergio; Wang, Jiayuan; Palmieri, Francesco

    2013-01-01

    infrastructures are now widely recognized to play a fundamental role in the emission of green-house gases (GHG) in the at- mosphere, signicantly aecting the environmental sustainability of new evolutions in network architectures as well as technological developments in communication devices. In this paper......, a novel eco-sustainable Routing and Wavelength Assignment (RWA) algorithm, based on shortest-path routing with an adaptive link weighting function relying on an extension of the OSPF-TE protocol to convey carbon footprint information, has been proposed to decrease the network ecological impact while...

  16. Using Sphinx to Improve Onion Routing Circuit Construction

    Science.gov (United States)

    Kate, Aniket; Goldberg, Ian

    This paper presents compact message formats for onion routing circuit construction using the Sphinx methodology developed for mixes. We significantly compress the circuit construction messages for three onion routing protocols that have emerged as enhancements to the Tor anonymizing network; namely, Tor with predistributed Diffie-Hellman values, pairing-based onion routing, and certificateless onion routing. Our new circuit constructions are also secure in the universal composability framework, a property that was missing from the original constructions. Further, we compare the performance of our schemes with their older counterparts as well as with each other.

  17. RFID-WSN integrated architecture for energy and delay- aware routing a simulation approach

    CERN Document Server

    Ahmed, Jameel; Tayyab, Muhammad; Nawaz, Menaa

    2015-01-01

    The book identifies the performance challenges concerning Wireless Sensor Networks (WSN) and Radio Frequency Identification (RFID) and analyzes their impact on the performance of routing protocols. It presents a thorough literature survey to identify the issues affecting routing protocol performance, as well as a mathematical model for calculating the end-to-end delays of the routing protocol ACQUIRE; a comparison of two routing protocols (ACQUIRE and DIRECTED DIFFUSION) is also provided for evaluation purposes. On the basis of the results and literature review, recommendations are made for better selection of protocols regarding the nature of the respective application and related challenges. In addition, this book covers a proposed simulator that integrates both RFID and WSN technologies. Therefore, the manuscript is divided in two major parts: an integrated architecture of smart nodes, and a power-optimized protocol for query and information interchange.

  18. Multipath Routing in Wireless Sensor Networks: Survey and Research Challenges

    Science.gov (United States)

    Radi, Marjan; Dezfouli, Behnam; Bakar, Kamalrulnizam Abu; Lee, Malrey

    2012-01-01

    A wireless sensor network is a large collection of sensor nodes with limited power supply and constrained computational capability. Due to the restricted communication range and high density of sensor nodes, packet forwarding in sensor networks is usually performed through multi-hop data transmission. Therefore, routing in wireless sensor networks has been considered an important field of research over the past decade. Nowadays, multipath routing approach is widely used in wireless sensor networks to improve network performance through efficient utilization of available network resources. Accordingly, the main aim of this survey is to present the concept of the multipath routing approach and its fundamental challenges, as well as the basic motivations for utilizing this technique in wireless sensor networks. In addition, we present a comprehensive taxonomy on the existing multipath routing protocols, which are especially designed for wireless sensor networks. We highlight the primary motivation behind the development of each protocol category and explain the operation of different protocols in detail, with emphasis on their advantages and disadvantages. Furthermore, this paper compares and summarizes the state-of-the-art multipath routing techniques from the network application point of view. Finally, we identify open issues for further research in the development of multipath routing protocols for wireless sensor networks. PMID:22368490

  19. Multipath routing in wireless sensor networks: survey and research challenges.

    Science.gov (United States)

    Radi, Marjan; Dezfouli, Behnam; Abu Bakar, Kamalrulnizam; Lee, Malrey

    2012-01-01

    A wireless sensor network is a large collection of sensor nodes with limited power supply and constrained computational capability. Due to the restricted communication range and high density of sensor nodes, packet forwarding in sensor networks is usually performed through multi-hop data transmission. Therefore, routing in wireless sensor networks has been considered an important field of research over the past decade. Nowadays, multipath routing approach is widely used in wireless sensor networks to improve network performance through efficient utilization of available network resources. Accordingly, the main aim of this survey is to present the concept of the multipath routing approach and its fundamental challenges, as well as the basic motivations for utilizing this technique in wireless sensor networks. In addition, we present a comprehensive taxonomy on the existing multipath routing protocols, which are especially designed for wireless sensor networks. We highlight the primary motivation behind the development of each protocol category and explain the operation of different protocols in detail, with emphasis on their advantages and disadvantages. Furthermore, this paper compares and summarizes the state-of-the-art multipath routing techniques from the network application point of view. Finally, we identify open issues for further research in the development of multipath routing protocols for wireless sensor networks.

  20. DIRECTIONAL OPPORTUNISTIC MECHANISM IN CLUSTER MESSAGE CRITICALITY LEVEL BASED ZIGBEE ROUTING

    OpenAIRE

    B.Rajeshkanna *1, Dr.M.Anitha 2

    2018-01-01

    The cluster message criticality level based zigbee routing(CMCLZOR) has been proposed for routing the cluster messages in wireless smart energy home area networks. It employs zigbee opportunistic shortcut tree routing(ZOSTR) and AODV individually for routing normal messages and highly critical messages respectively. ZOSTR allows the receiving nodes to compete for forwarding a packet with the priority of left-over hops rather than stating single next hop node like unicast protocols. Since it h...

  1. Energy Efficient Routing in Wireless Sensor Networks Through Balanced Clustering

    Directory of Open Access Journals (Sweden)

    Christos Douligeris

    2013-01-01

    Full Text Available The wide utilization of Wireless Sensor Networks (WSNs is obstructed by the severely limited energy constraints of the individual sensor nodes. This is the reason why a large part of the research in WSNs focuses on the development of energy efficient routing protocols. In this paper, a new protocol called Equalized Cluster Head Election Routing Protocol (ECHERP, which pursues energy conservation through balanced clustering, is proposed. ECHERP models the network as a linear system and, using the Gaussian elimination algorithm, calculates the combinations of nodes that can be chosen as cluster heads in order to extend the network lifetime. The performance evaluation of ECHERP is carried out through simulation tests, which evince the effectiveness of this protocol in terms of network energy efficiency when compared against other well-known protocols.

  2. Understanding individual routing behaviour.

    Science.gov (United States)

    Lima, Antonio; Stanojevic, Rade; Papagiannaki, Dina; Rodriguez, Pablo; González, Marta C

    2016-03-01

    Knowing how individuals move between places is fundamental to advance our understanding of human mobility (González et al. 2008 Nature 453, 779-782. (doi:10.1038/nature06958)), improve our urban infrastructure (Prato 2009 J. Choice Model. 2, 65-100. (doi:10.1016/S1755-5345(13)70005-8)) and drive the development of transportation systems. Current route-choice models that are used in transportation planning are based on the widely accepted assumption that people follow the minimum cost path (Wardrop 1952 Proc. Inst. Civ. Eng. 1, 325-362. (doi:10.1680/ipeds.1952.11362)), despite little empirical support. Fine-grained location traces collected by smart devices give us today an unprecedented opportunity to learn how citizens organize their travel plans into a set of routes, and how similar behaviour patterns emerge among distinct individual choices. Here we study 92 419 anonymized GPS trajectories describing the movement of personal cars over an 18-month period. We group user trips by origin-destination and we find that most drivers use a small number of routes for their routine journeys, and tend to have a preferred route for frequent trips. In contrast to the cost minimization assumption, we also find that a significant fraction of drivers' routes are not optimal. We present a spatial probability distribution that bounds the route selection space within an ellipse, having the origin and the destination as focal points, characterized by high eccentricity independent of the scale. While individual routing choices are not captured by path optimization, their spatial bounds are similar, even for trips performed by distinct individuals and at various scales. These basic discoveries can inform realistic route-choice models that are not based on optimization, having an impact on several applications, such as infrastructure planning, routing recommendation systems and new mobility solutions. © 2016 The Author(s).

  3. Path Diversity Improved Opportunistic Routing for Underwater Sensor Networks.

    Science.gov (United States)

    Bai, Weigang; Wang, Haiyan; He, Ke; Zhao, Ruiqin

    2018-04-23

    The packets carried along a pre-defined route in underwater sensor networks are very vulnerble. Node mobility or intermittent channel availability easily leads to unreachable routing. Opportunistic routing has been proven to be a promising paradigm to design routing protocols for underwater sensor networks. It takes advantage of the broadcast nature of the wireless medium to combat packet losses and selects potential paths on the fly. Finding an appropriate forwarding candidate set is a key issue in opportunistic routing. Many existing solutions ignore the impact of candidates location distribution on packet forwarding. In this paper, a path diversity improved candidate selection strategy is applied in opportunistic routing to improve packet forwarding efficiency. It not only maximizes the packet forwarding advancements but also takes the candidate’s location distribution into account. Based on this strategy, we propose two effective routing protocols: position improved candidates selection (PICS) and position random candidates selection (PRCS). PICS employs two-hop neighbor information to make routing decisions. PRCS only uses one-hop neighbor information. Simulation results show that both PICS and PRCS can significantly improve network performance when compared with the previous solutions, in terms of packet delivery ratio, average energy consumption and end-to-end delay.

  4. Path Diversity Improved Opportunistic Routing for Underwater Sensor Networks

    Directory of Open Access Journals (Sweden)

    Weigang Bai

    2018-04-01

    Full Text Available The packets carried along a pre-defined route in underwater sensor networks are very vulnerble. Node mobility or intermittent channel availability easily leads to unreachable routing. Opportunistic routing has been proven to be a promising paradigm to design routing protocols for underwater sensor networks. It takes advantage of the broadcast nature of the wireless medium to combat packet losses and selects potential paths on the fly. Finding an appropriate forwarding candidate set is a key issue in opportunistic routing. Many existing solutions ignore the impact of candidates location distribution on packet forwarding. In this paper, a path diversity improved candidate selection strategy is applied in opportunistic routing to improve packet forwarding efficiency. It not only maximizes the packet forwarding advancements but also takes the candidate’s location distribution into account. Based on this strategy, we propose two effective routing protocols: position improved candidates selection (PICS and position random candidates selection (PRCS. PICS employs two-hop neighbor information to make routing decisions. PRCS only uses one-hop neighbor information. Simulation results show that both PICS and PRCS can significantly improve network performance when compared with the previous solutions, in terms of packet delivery ratio, average energy consumption and end-to-end delay.

  5. Delay Tolerance in Underwater Wireless Communications: A Routing Perspective

    Directory of Open Access Journals (Sweden)

    Safdar Hussain Bouk

    2016-01-01

    Full Text Available Similar to terrestrial networks, underwater wireless networks (UWNs also aid several critical tasks including coastal surveillance, underwater pollution detection, and other maritime applications. Currently, once underwater sensor nodes are deployed at different levels of the sea, it is nearly impossible or very expensive to reconfigure the hardware, for example, battery. Taking this issue into account, considerable amount of research has been carried out to ensure minimum energy costs and reliable communication between underwater nodes and base stations. As a result, several different network protocols were proposed for UWN, including MAC, PHY, transport, and routing. Recently, a new paradigm was introduced claiming that the intermittent nature of acoustic channel and signal resulted in designing delay tolerant routing schemes for the UWN, known as an underwater delay tolerant network. In this paper, we provide a comprehensive survey of underwater routing protocols with emphasis on the limitations, challenges, and future open issues in the context of delay tolerant network routing.

  6. Multi-hop routing in wireless sensor networks an overview, taxonomy, and research challenges

    CERN Document Server

    Rani, Shalli

    2016-01-01

    This brief provides an overview of recent developments in multi-hop routing protocols for Wireless Sensor Networks (WSNs). It introduces the various classifications of routing protocols and lists the pros and cons of each category, going beyond the conceptual overview of routing classifications offered in other books. Recently many researchers have proposed numerous multi-hop routing protocols and thereby created a need for a book that provides its readers with an up-to-date road map of this research paradigm.   The authors present some of the most relevant results achieved by applying an algorithmic approach to the research on multi-hop routing protocols. The book covers measurements, experiences and lessons learned from the implementation of multi-hop communication prototypes. Furthermore, it describes future research challenges and as such serves as a useful guide for students and researchers alike.

  7. Routing and scheduling problems

    DEFF Research Database (Denmark)

    Reinhardt, Line Blander

    couple of decades. To deliver competitive service and price, transportation today needs to be cost effective. A company requiring for things to be shipped will aim at having the freight shipped as cheaply as possible while often satisfying certain time constraints. For the transportation company......, the effectiveness of the network is of importance aiming at satisfying as many costumer demands as possible at a low cost. Routing represent a path between locations such as an origin and destination for the object routed. Sometimes routing has a time dimension as well as the physical paths. This may...... set cost making the cost of the individual vehicle routes inter-dependant. Depending on the problem type, the size of the problems and time available for solving, different solution methods can be applicable. In this thesis both heuristic methods and several exact methods are investigated depending...

  8. Proxies for Anonymous Routing

    National Research Council Canada - National Science Library

    Reed, Michael G; Syverson, Paul F; Goldschlag, David M

    1996-01-01

    ...), and file transfers (FTP) have been implemented. Onion routing provides application independent, real-time, and bi-directional anonymous connections that are resistant to both eavesdropping and traffic analysis...

  9. Routes and Stations

    Data.gov (United States)

    Department of Homeland Security — he Routes_Stations table is composed of fixed rail transit systems within the Continental United States, Alaska, Hawaii, the District of Columbia, and Puerto Rico....

  10. Contention aware mobility prediction routing for intermittently connected mobile networks

    KAUST Repository

    Elwhishi, Ahmed; Ho, Pin-Han; Shihada, Basem

    2013-01-01

    This paper introduces a novel multi-copy routing protocol, called predict and forward (PF), for delay tolerant networks, which aims to explore the possibility of using mobile nodes as message carriers for end-to-end delivery of the messages. With PF, the message forwarding decision is made by manipulating the probability distribution of future inter-contact and contact durations based on the network status, including wireless link condition and nodal buffer availability. In particular, PF is based on the observations that the node mobility behavior is semi-deterministic and could be predicted once there is sufficient mobility history information. We implemented the proposed protocol and compared it with a number of existing encounter-based routing approaches in terms of delivery delay, delivery ratio, and the number of transmissions required for message delivery. The simulation results show that PF outperforms all the counterpart multi-copy encounter-based routing protocols considered in the study.

  11. Contention aware mobility prediction routing for intermittently connected mobile networks

    KAUST Repository

    Elwhishi, Ahmed

    2013-04-26

    This paper introduces a novel multi-copy routing protocol, called predict and forward (PF), for delay tolerant networks, which aims to explore the possibility of using mobile nodes as message carriers for end-to-end delivery of the messages. With PF, the message forwarding decision is made by manipulating the probability distribution of future inter-contact and contact durations based on the network status, including wireless link condition and nodal buffer availability. In particular, PF is based on the observations that the node mobility behavior is semi-deterministic and could be predicted once there is sufficient mobility history information. We implemented the proposed protocol and compared it with a number of existing encounter-based routing approaches in terms of delivery delay, delivery ratio, and the number of transmissions required for message delivery. The simulation results show that PF outperforms all the counterpart multi-copy encounter-based routing protocols considered in the study.

  12. Bioremediation protocols

    National Research Council Canada - National Science Library

    Sheehan, David

    1997-01-01

    ..., .. . . . . .. ,. . . .. . . . . . . . .. . . . . .. . . .. . .. 3 2 Granular Nina Sludge Christiansen, Consortia lndra for Bioremediation, M. Mathrani, and Birgitte K. Ahring . 23 PART II PROTOCOLS...

  13. Routed planar networks

    Directory of Open Access Journals (Sweden)

    David J. Aldous

    2016-04-01

    Full Text Available Modeling a road network as a planar graph seems very natural. However, in studying continuum limits of such networks it is useful to take {\\em routes} rather than {\\em edges} as primitives. This article is intended to introduce the relevant (discrete setting notion of {\\em routed network} to graph theorists. We give a naive classification of all 71 topologically different such networks on 4 leaves, and pose a variety of challenging research questions.

  14. Enhanced Contact Graph Routing (ECGR) MACHETE Simulation Model

    Science.gov (United States)

    Segui, John S.; Jennings, Esther H.; Clare, Loren P.

    2013-01-01

    Contact Graph Routing (CGR) for Delay/Disruption Tolerant Networking (DTN) space-based networks makes use of the predictable nature of node contacts to make real-time routing decisions given unpredictable traffic patterns. The contact graph will have been disseminated to all nodes before the start of route computation. CGR was designed for space-based networking environments where future contact plans are known or are independently computable (e.g., using known orbital dynamics). For each data item (known as a bundle in DTN), a node independently performs route selection by examining possible paths to the destination. Route computation could conceivably run thousands of times a second, so computational load is important. This work refers to the simulation software model of Enhanced Contact Graph Routing (ECGR) for DTN Bundle Protocol in JPL's MACHETE simulation tool. The simulation model was used for performance analysis of CGR and led to several performance enhancements. The simulation model was used to demonstrate the improvements of ECGR over CGR as well as other routing methods in space network scenarios. ECGR moved to using earliest arrival time because it is a global monotonically increasing metric that guarantees the safety properties needed for the solution's correctness since route re-computation occurs at each node to accommodate unpredicted changes (e.g., traffic pattern, link quality). Furthermore, using earliest arrival time enabled the use of the standard Dijkstra algorithm for path selection. The Dijkstra algorithm for path selection has a well-known inexpensive computational cost. These enhancements have been integrated into the open source CGR implementation. The ECGR model is also useful for route metric experimentation and comparisons with other DTN routing protocols particularly when combined with MACHETE's space networking models and Delay Tolerant Link State Routing (DTLSR) model.

  15. A Performance Evaluation of NACK-Oriented Protocols as the Foundation of Reliable Delay- Tolerant Networking Convergence Layers

    Science.gov (United States)

    Iannicca, Dennis; Hylton, Alan; Ishac, Joseph

    2012-01-01

    Delay-Tolerant Networking (DTN) is an active area of research in the space communications community. DTN uses a standard layered approach with the Bundle Protocol operating on top of transport layer protocols known as convergence layers that actually transmit the data between nodes. Several different common transport layer protocols have been implemented as convergence layers in DTN implementations including User Datagram Protocol (UDP), Transmission Control Protocol (TCP), and Licklider Transmission Protocol (LTP). The purpose of this paper is to evaluate several stand-alone implementations of negative-acknowledgment based transport layer protocols to determine how they perform in a variety of different link conditions. The transport protocols chosen for this evaluation include Consultative Committee for Space Data Systems (CCSDS) File Delivery Protocol (CFDP), Licklider Transmission Protocol (LTP), NACK-Oriented Reliable Multicast (NORM), and Saratoga. The test parameters that the protocols were subjected to are characteristic of common communications links ranging from terrestrial to cis-lunar and apply different levels of delay, line rate, and error.

  16. Improved AODV route recovery in mobile ad-hoc networks using a genetic algorithm

    Directory of Open Access Journals (Sweden)

    Ahmad Maleki

    2014-09-01

    Full Text Available An important issue in ad-hoc on-demand distance vector (AODV routing protocols is route failure caused by node mobility in the MANETs. The AODV requires a new route discovery procedure whenever a route breaks and these frequent route discoveries increase transmission delays and routing overhead. The present study proposes a new method for AODVs using a genetic algorithm to improve the route recovery mechanism. When failure occurs in a route, the proposed method (GAAODV makes decisions regarding the QOS parameter to select source or local repair. The task of the genetic algorithm is to find an appropriate combination of weights to optimize end-to-end delay. This paper evaluates the metrics of routing overhead, average end-to-end delay, and packet delivery ratio. Comparison of the new algorithm and AODV (RFC 3561 using a NS-2 simulator shows that GAAODV obtains better results for the QOS parameters.

  17. Wavelength conversion, time demultiplexing and multicasting based on cross-phase modulation and four-wave mixing in dispersion-flattened highly nonlinear photonic crystal fiber

    International Nuclear Information System (INIS)

    Hui, Zhan-Qiang; Zhang, Jian-Guo

    2012-01-01

    We propose the use of cross-phase modulation (XPM) and four-wave mixing (FWM) in dispersion-flattened highly nonlinear photonic crystal fibers (HNL-PCFs) to implement the functionalities of wavelength conversion, simultaneous time demultiplexing and wavelength multicasting in optical time-division multiplexing (OTDM) systems. The experiments on wavelength conversion at 80 Gbit s −1 and OTDM demultiplexing from 80 to 10 Gbit s −1 with wavelength multicasting of two channels are successfully demonstrated to validate the proposed scheme, which are carried out by using two segments of dispersion-flattened HNL-PCFs with lengths of 100 and 50 m, respectively. Moreover, the bit error rate (BER) performance is also measured. The results show that our designed system can achieve a power penalty of less than 4.6 dB for two multicasting channels with a 24 nm wavelength span at the BER of 10 −9 when compared with the 10 Gbit/s back-to-back measurement. The proposed system is transparent to bit rate since only an ultrafast third-order nonlinear effect is used. The resulting configuration is compact, robust and reliable, benefiting from the use of dispersion-flattened HNL-PCFs with short lengths. This also makes the proposed system more flexible in the operational wavelengths than those based on dispersion-shifted fibers and traditional highly nonlinear fibers. (paper)

  18. DTN routing in body sensor networks with dynamic postural partitioning.

    Science.gov (United States)

    Quwaider, Muhannad; Biswas, Subir

    2010-11-01

    This paper presents novel store-and-forward packet routing algorithms for Wireless Body Area Networks ( WBAN ) with frequent postural partitioning. A prototype WBAN has been constructed for experimentally characterizing on-body topology disconnections in the presence of ultra short range radio links, unpredictable RF attenuation, and human postural mobility. On-body DTN routing protocols are then developed using a stochastic link cost formulation, capturing multi-scale topological localities in human postural movements. Performance of the proposed protocols are evaluated experimentally and via simulation, and are compared with a number of existing single-copy DTN routing protocols and an on-body packet flooding mechanism that serves as a performance benchmark with delay lower-bound. It is shown that via multi-scale modeling of the spatio-temporal locality of on-body link disconnection patterns, the proposed algorithms can provide better routing performance compared to a number of existing probabilistic, opportunistic, and utility-based DTN routing protocols in the literature.

  19. Study protocol for a prospective cohort study examining the predictive potential of dynamic symptom networks for the onset and progression of psychosis: the Mapping Individual Routes of Risk and Resilience (Mirorr) study.

    Science.gov (United States)

    Booij, Sanne H; Wichers, Marieke; de Jonge, Peter; Sytema, Sjoerd; van Os, Jim; Wunderink, Lex; Wigman, Johanna T W

    2018-01-21

    Our current ability to predict the course and outcome of early psychotic symptoms is limited, hampering timely treatment. To improve our understanding of the development of psychosis, a different approach to psychopathology may be productive. We propose to reconceptualise psychopathology from a network perspective, according to which symptoms act as a dynamic, interconnected system, impacting on each other over time and across diagnostic boundaries to form symptom networks. Adopting this network approach, the Mapping Individual Routes of Risk and Resilience study aims to determine whether characteristics of symptom networks can predict illness course and outcome of early psychotic symptoms. The sample consists of n=100 participants aged 18-35 years, divided into four subgroups (n=4×25) with increasing levels of severity of psychopathology, representing successive stages of clinical progression. Individuals representing the initial stage have a relatively low expression of psychotic experiences (general population), whereas individuals representing the end stage are help seeking and display a psychometric expression of psychosis, putting them at ultra-high risk for transition to psychotic disorder. At baseline and 1-year follow-up, participants report their symptoms, affective states and experiences for three consecutive months in short, daily questionnaires on their smartphone, which will be used to map individual networks. Network parameters, including the strength and directionality of symptom connections and centrality indices, will be estimated and associated to individual differences in and within-individual progression through stages of clinical severity and functioning over the next 3 years. The study has been approved by the local medical ethical committee (ABR no. NL52974.042.15). The results of the study will be published in (inter)national peer-reviewed journals, presented at research, clinical and general public conferences. The results will assist

  20. Transmission Scheduling and Routing Algorithms for Delay Tolerant Networks

    Science.gov (United States)

    Dudukovich, Rachel; Raible, Daniel E.

    2016-01-01

    The challenges of data processing, transmission scheduling and routing within a space network present a multi-criteria optimization problem. Long delays, intermittent connectivity, asymmetric data rates and potentially high error rates make traditional networking approaches unsuitable. The delay tolerant networking architecture and protocols attempt to mitigate many of these issues, yet transmission scheduling is largely manually configured and routes are determined by a static contact routing graph. A high level of variability exists among the requirements and environmental characteristics of different missions, some of which may allow for the use of more opportunistic routing methods. In all cases, resource allocation and constraints must be balanced with the optimization of data throughput and quality of service. Much work has been done researching routing techniques for terrestrial-based challenged networks in an attempt to optimize contact opportunities and resource usage. This paper examines several popular methods to determine their potential applicability to space networks.

  1. Routing in Mobile Wireless Sensor Networks: A Leader-Based Approach.

    Science.gov (United States)

    Burgos, Unai; Amozarrain, Ugaitz; Gómez-Calzado, Carlos; Lafuente, Alberto

    2017-07-07

    This paper presents a leader-based approach to routing in Mobile Wireless Sensor Networks (MWSN). Using local information from neighbour nodes, a leader election mechanism maintains a spanning tree in order to provide the necessary adaptations for efficient routing upon the connectivity changes resulting from the mobility of sensors or sink nodes. We present two protocols following the leader election approach, which have been implemented using Castalia and OMNeT++. The protocols have been evaluated, besides other reference MWSN routing protocols, to analyse the impact of network size and node velocity on performance, which has demonstrated the validity of our approach.

  2. Neighboring and Connectivity-Aware Routing in VANETs

    Directory of Open Access Journals (Sweden)

    Huma Ghafoor

    2014-01-01

    Full Text Available A novel position-based routing protocol anchor-based connectivity-aware routing (ACAR for vehicular ad hoc networks (VANETs is proposed in this paper to ensure connectivity of routes with more successfully delivered packets. Both buses and cars are considered as vehicular nodes running in both clockwise and anticlockwise directions in a city scenario. Both directions are taken into account for faster communication. ACAR is a hybrid protocol, using both the greedy forwarding approach and the store-carry-and-forward approach to minimize the packet drop rate on the basis of certain assumptions. Our solution to situations that occur when the network is sparse and when any (source or intermediate node has left its initial position makes this protocol different from those existing in the literature. We consider only vehicle-to-vehicle (V2V communication in which both the source and destination nodes are moving vehicles. Also, no road-side units are considered. Finally, we compare our protocol with A-STAR (a plausible connectivity-aware routing protocol for city environments, and simulation results in NS-2 show improvement in the number of packets delivered to the destination using fewer hops. Also, we show that ACAR has more successfully-delivered long-distance packets with reasonable packet delay than A-STAR.

  3. ARBR: Adaptive reinforcement-based routing for DTN

    KAUST Repository

    Elwhishi, Ahmed

    2010-10-01

    This paper introduces a novel routing protocol in Delay Tolerant Networks (DTNs), aiming to solve the online distributed routing problem. By manipulating a collaborative reinforcement learning technique, a group of nodes can cooperate with each other and make a forwarding decision for the stored messages based on a cost function at each contact with another node. The proposed protocol is characterized by not only considering the contact time statistics under a novel contact model, but also looks into the feedback on user behavior and network conditions, such as congestion and buffer occupancy sampled during each previous contact with any other node. Therefore, the proposed protocol can achieve high efficiency via an adaptive and intelligent routing mechanism according to network conditions. Extensive simulation is conducted to verify the proposed protocol, where a comparison is made with a number of existing encounter-based routing protocols in term of the number of transmissions of each message, message delivery delay, and delivery ratio. The results of the simulation demonstrate the effectiveness of the proposed technique.

  4. Location-Aided Reliable Routing for Opportunistic Networks

    Institute of Scientific and Technical Information of China (English)

    Yong Yang; Zhi Ren; Jibi Li

    2012-01-01

    In our study, we investigate the problem of location-based routing in opportunistic networks. Due to the uncertainty of end-to-end paths between sources and destinations, the classical location-based ad hoc routing protocols cannot adapt to the environment of opportunistic networks, which leads to the decrease of the delivery rate of data. To address it, we propose in this paper a novel location-aided routing protocol which is suitable for opportunistic networks. In our protocol, a node can send location information on demand by using prediction mechanism, and when sending a data packet, the node chooses multiple neighbors which are closer to the destination as next hops. If the candidate neighbors do not exist, the node carries the data till it meets a proper neighbor or the destination. Theoretical analysis and simulation results show that our proposed protocol outperforms DREAM (Distance Routing Effect Protocol Mobility) and one of its improved versions, BFDREAM (Boundary Forwarding DREAM), in terms of the delivery rate and overhead.

  5. Routing in IPv6 over Low-Power Wireless Personal Area Networks (6LoWPAN: A Survey

    Directory of Open Access Journals (Sweden)

    Vinay Kumar

    2012-01-01

    Full Text Available 6LoWPANs (IPv6-based Low-Power Personal Area Networks are formulated by devices that are compatible with the IEEE 802.15.4 standard. To moderate the effects of network mobility, the Internet Protocol (IP does not calculate routes; it is left to a routing protocol, which maintains routing tables in the routers. 6LowPAN uses an adaptation layer between the network (IPv6 and data link layer (IEEE802.15.4 MAC to fragment and reassemble IPv6 packets. The routing in 6LoWPAN is primarily divided on the basis of routing decision taken on adaptation or network layer. The objective of this paper is to present a state-of-the-art survey of existing routing protocols: LOAD, M-LOAD, DYMO-Low, Hi-Low, Extended Hi-Low, and S-AODV. These routing protocols have compared on the basis of different metric like energy consumption, memory uses, mobility, scalability, routing delay, an RERR message, a Hello message, and local repair. We have also presented the taxonomy of routing requirement; parameter for evaluating routing algorithm, and it was found that the routing protocol has its own advantages depending upon the application where it is used.

  6. Flexible and re-configurable optical three-input XOR logic gate of phase-modulated signals with multicast functionality for potential application in optical physical-layer network coding.

    Science.gov (United States)

    Lu, Guo-Wei; Qin, Jun; Wang, Hongxiang; Ji, XuYuefeng; Sharif, Gazi Mohammad; Yamaguchi, Shigeru

    2016-02-08

    Optical logic gate, especially exclusive-or (XOR) gate, plays important role in accomplishing photonic computing and various network functionalities in future optical networks. On the other hand, optical multicast is another indispensable functionality to efficiently deliver information in optical networks. In this paper, for the first time, we propose and experimentally demonstrate a flexible optical three-input XOR gate scheme for multiple input phase-modulated signals with a 1-to-2 multicast functionality for each XOR operation using four-wave mixing (FWM) effect in single piece of highly-nonlinear fiber (HNLF). Through FWM in HNLF, all of the possible XOR operations among input signals could be simultaneously realized by sharing a single piece of HNLF. By selecting the obtained XOR components using a followed wavelength selective component, the number of XOR gates and the participant light in XOR operations could be flexibly configured. The re-configurability of the proposed XOR gate and the function integration of the optical logic gate and multicast in single device offer the flexibility in network design and improve the network efficiency. We experimentally demonstrate flexible 3-input XOR gate for four 10-Gbaud binary phase-shift keying signals with a multicast scale of 2. Error-free operations for the obtained XOR results are achieved. Potential application of the integrated XOR and multicast function in network coding is also discussed.

  7. Collective network routing

    Science.gov (United States)

    Hoenicke, Dirk

    2014-12-02

    Disclosed are a unified method and apparatus to classify, route, and process injected data packets into a network so as to belong to a plurality of logical networks, each implementing a specific flow of data on top of a common physical network. The method allows to locally identify collectives of packets for local processing, such as the computation of the sum, difference, maximum, minimum, or other logical operations among the identified packet collective. Packets are injected together with a class-attribute and an opcode attribute. Network routers, employing the described method, use the packet attributes to look-up the class-specific route information from a local route table, which contains the local incoming and outgoing directions as part of the specifically implemented global data flow of the particular virtual network.

  8. Optimizing well intervention routes

    Energy Technology Data Exchange (ETDEWEB)

    Paiva, Ronaldo O. [PETROBRAS S.A., Vitoria, ES (Brazil); Schiozer, Denis J.; Bordalo, Sergio N. [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia Mecanica. Centro de Estudo do Petroleo (CEPETRO)]. E-mail: denis@dep.fem.unicamp.br; bordalo@dep.fem.unicamp.br

    2000-07-01

    This work presents a method for optimizing the itinerary of work over rigs, i.e., the search for the route of minimum total cost, and demonstrates the importance of the dynamics of reservoir behaviour. The total cost of a route includes the rig expenses (transport, assembly and operation), which are functions of time and distances, plus the losses of revenue in wells waiting for the rig, which are also dependent of time. A reservoir simulator is used to evaluate the monetary influence of the well shutdown on the present value of the production curve. Finally, search algorithms are employed to determine the route of minimal cost. The Simulated Annealing algorithm was also successful in optimizing the distribution of a list of wells among different work over rigs. The rational approach presented here is recommended for management teams as a standard procedure to define the priority of wells scheduled for work over. (author)

  9. LKHW: A Directed Diffusion-Based Secure Multicast Scheme for Wireless Sensor Networks

    NARCIS (Netherlands)

    Di Pietro, Roberto; Mancini, Luigi V.; Law, Y.W.; Etalle, Sandro; Havinga, Paul J.M.; Huang, C.H; Ramanujam, J.

    2003-01-01

    We present a mechanism for securing group communications in Wireless Sensor Networks (WSN). First, we derive an extension of Logical Key Hierarchy (LKH). Then we merge the extension with Directed Diffusion (DD). The resulting protocol, LKHW, combines the advantages of both LKH and DD. In particular,

  10. LKHW: A Directed Diffusion-Based Secure Multicast Scheme for Wireless Sensor Networks

    NARCIS (Netherlands)

    Di Pietro, Roberto; Mancini, Luigi V.; Law, Y.W.; Etalle, Sandro; Havinga, Paul J.M.

    In this paper, we present a mechanism for securing group communications in Wireless Sensor Networks (WSN). First, we derive an extension of Logical Key Hierarchy (LKH). Then we merge the extension with directed diffusion. The resulting protocol, LKHW, combines the advantages of both LKH and directed

  11. SET-Routes programme

    CERN Multimedia

    Marietta Schupp, EMBL Photolab

    2008-01-01

    Dr Sabine Hentze, specialist in human genetics, giving an Insight Lecture entitled "Human Genetics – Diagnostics, Indications and Ethical Issues" on 23 September 2008 at EMBL Heidelberg. Activities in a achool in Budapest during a visit of Angela Bekesi, Ambassadors for the SET-Routes programme.

  12. Design alternatives for wavelength routing networks

    Science.gov (United States)

    Miliotis, K.; Papadimitriou, G. I.; Pomportsis, A. S.

    2003-03-01

    This paper attempts to provide a high level overview of many of the technologies employed in optical networks with a focus on wavelength-routing networks. Optical networks involve a number of technologies from the physics of light through protocols and networks architectures. In fact there is so much technology and know-how that most people involved with optical networks only have a full understanding of the narrow area they deal with. We start first examining the principles that govern light and its use as a wave guide, and then turn our focus to the various components that constitute an optical network and conclude with the description of all optical networks and wavelength-routed networks in greater detail.

  13. An Emergency-Adaptive Routing Scheme for Wireless Sensor Networks for Building Fire Hazard Monitoring

    Directory of Open Access Journals (Sweden)

    Guilin Zheng

    2011-03-01

    Full Text Available Fire hazard monitoring and evacuation for building environments is a novel application area for the deployment of wireless sensor networks. In this context, adaptive routing is essential in order to ensure safe and timely data delivery in building evacuation and fire fighting resource applications. Existing routing mechanisms for wireless sensor networks are not well suited for building fires, especially as they do not consider critical and dynamic network scenarios. In this paper, an emergency-adaptive, real-time and robust routing protocol is presented for emergency situations such as building fire hazard applications. The protocol adapts to handle dynamic emergency scenarios and works well with the routing hole problem. Theoretical analysis and simulation results indicate that our protocol provides a real-time routing mechanism that is well suited for dynamic emergency scenarios in building fires when compared with other related work.

  14. The Prohibitive Link between Position-based Routing and Planarity

    Directory of Open Access Journals (Sweden)

    David Cairns

    2013-12-01

    Full Text Available Position-based routing is touted as an ideal routing strategy for resource-constrained wireless networks. One persistent barrier to adoption is due to its recovery phase, where messages are forwarded according to leftor right-hand rule (LHR. This is often referred to as face-routing. In this paper we investigate the limits of LHR with respect to planarity.We show that the gap between non-planarity and successful delivery is a single link within a single configuration. Our work begins with an analysis to enumerate all node configurations that cause intersections in the unit-disc graph. We find that left-hand rule is able to recover from all but a single case, the ‘umbrella’ configuration so named for its appearance. We use this information to propose the Prohibitive Link Detection Protocol (PLDP that can guarantee delivery over non-planar graphs using standard face-routing techniques. As the name implies, the protocol detects and circumvents the ‘bad’ links that hamper LHR. The goal of this work is to maintain routing guarantees while disturbing the network graph as little as possible. In doing so, a new starting point emerges from which to build rich distributed protocols in the spirit of CLDP and GDSTR.

  15. Privacy-Preserving Interdomain Routing at Internet Scale

    Directory of Open Access Journals (Sweden)

    Asharov Gilad

    2017-07-01

    Full Text Available The Border Gateway Protocol (BGP computes routes between the organizational networks that make up today’s Internet. Unfortunately, BGP suffers from deficiencies, including slow convergence, security problems, a lack of innovation, and the leakage of sensitive information about domains’ routing preferences. To overcome some of these problems, we revisit the idea of centralizing and using secure multi-party computation (MPC for interdomain routing which was proposed by Gupta et al. (ACM HotNets’12. We implement two algorithms for interdomain routing with state-of-the-art MPC protocols. On an empirically derived dataset that approximates the topology of today’s Internet (55 809 nodes, our protocols take as little as 6 s of topology-independent precomputation and only 3 s of online time. We show, moreover, that when our MPC approach is applied at country/region-level scale, runtimes can be as low as 0.17 s online time and 0.20 s pre-computation time. Our results motivate the MPC approach for interdomain routing and furthermore demonstrate that current MPC techniques are capable of efficiently tackling real-world problems at a large scale.

  16. Distributed Fault-Tolerant Quality Of Service Routing in Hybrid Directional Wireless Networks

    National Research Council Canada - National Science Library

    Llewellyn, II, Larry C

    2007-01-01

    This thesis presents a distributed fault-tolerant routing protocol (EFDCB) for QoS supporting hybrid mobile ad hoc networks with the aim of mitigating QoS disruption time when network failures occur...

  17. On-Demand Routing in Multi-hop Wireless Mobile Ad Hoc Networks

    National Research Council Canada - National Science Library

    Maltz, David A

    2001-01-01

    .... Routing protocols used in ad hoc networks must automatically adjust to environments that can vary between the extremes of high mobility with low bandwidth, and low mobility with high bandwidth...

  18. Integer-linear-programing optimization in scalable video multicast with adaptive modulation and coding in wireless networks.

    Science.gov (United States)

    Lee, Dongyul; Lee, Chaewoo

    2014-01-01

    The advancement in wideband wireless network supports real time services such as IPTV and live video streaming. However, because of the sharing nature of the wireless medium, efficient resource allocation has been studied to achieve a high level of acceptability and proliferation of wireless multimedia. Scalable video coding (SVC) with adaptive modulation and coding (AMC) provides an excellent solution for wireless video streaming. By assigning different modulation and coding schemes (MCSs) to video layers, SVC can provide good video quality to users in good channel conditions and also basic video quality to users in bad channel conditions. For optimal resource allocation, a key issue in applying SVC in the wireless multicast service is how to assign MCSs and the time resources to each SVC layer in the heterogeneous channel condition. We formulate this problem with integer linear programming (ILP) and provide numerical results to show the performance under 802.16 m environment. The result shows that our methodology enhances the overall system throughput compared to an existing algorithm.

  19. Integer-Linear-Programing Optimization in Scalable Video Multicast with Adaptive Modulation and Coding in Wireless Networks

    Directory of Open Access Journals (Sweden)

    Dongyul Lee

    2014-01-01

    Full Text Available The advancement in wideband wireless network supports real time services such as IPTV and live video streaming. However, because of the sharing nature of the wireless medium, efficient resource allocation has been studied to achieve a high level of acceptability and proliferation of wireless multimedia. Scalable video coding (SVC with adaptive modulation and coding (AMC provides an excellent solution for wireless video streaming. By assigning different modulation and coding schemes (MCSs to video layers, SVC can provide good video quality to users in good channel conditions and also basic video quality to users in bad channel conditions. For optimal resource allocation, a key issue in applying SVC in the wireless multicast service is how to assign MCSs and the time resources to each SVC layer in the heterogeneous channel condition. We formulate this problem with integer linear programming (ILP and provide numerical results to show the performance under 802.16 m environment. The result shows that our methodology enhances the overall system throughput compared to an existing algorithm.

  20. Trust-Based Route Selection in Dynamic Source Routin

    DEFF Research Database (Denmark)

    Jensen, Christian D.; Connell, Paul O

    2006-01-01

    in the mobile wireless network. However, blindly trusting all other nodes to respect the routing protocol exposes the local node to a wide variety of vulnerabilities. Traditional security mechanisms rely on either the authenticated identity of the requesting principal or some form of credentials that authorise...

  1. A novel insight into beaconless geo-routing

    KAUST Repository

    Bader, Ahmed

    2012-12-01

    Beaconless geo-routing protocols have been traditionally analyzed assuming equal communication ranges for the data and control packets. This is not true in reality, since the communication range is in practice function of the packet length. As a consequence, a substantial discrepancy may exist between analytical and empirical results offered in beaconless geo-routing literature. Furthermore, performance of beaconless geo-routing protocols has typically considered using single-hop metrics only. End-to-end performance is considered in literature only occasionally and mainly in terms of simulation only. In this paper, we re-examine this class of protocols. We first incorporate practical packet detection models in order to capture the dependency of the communication range on the packet\\'s length. We then develop a detailed analytical framework for the end-to-end delay and energy performance of beaconless geo-routing protocols. Finally, we present two different application scenarios and study various tradeoffs in light of the framework developed. © 2012 IEEE.

  2. Deflection routing scheme for GMPLS-based OBS networks

    DEFF Research Database (Denmark)

    Eid, Arafat; Mahmood, Waqar; Alomar, Anwar

    2010-01-01

    Integrating the Generalized Multi-Protocol Label Switching (GMPLS) framework into an Optical Burst Switching (OBS) Control Plane is a promising solution to alleviating most of OBS performance and design issues. However, implementing the already proposed OBS deflection routing schemes is not appli...

  3. Contention Aware Routing for Intermittently Connected Mobile Networks

    KAUST Repository

    Elwhishi, Ahmed; Ho, Pin Han; Naik, Sagar; Shihada, Basem

    2011-01-01

    This paper introduces a novel multi-copy routing protocol, called Self Adaptive Utility-based Routing Protocol (SAURP), for Delay Tolerant Networks (DTNs) that are possibly composed of a vast number of miniature devices such as smart phones, hand-held devices, and sensors mounted in fixed or mobile objects. SAURP aims to explore the possibility of taking mobile nodes as message carriers in order for end-to-end delivery of the messages. The best carrier for a message is determined by the prediction result using a novel contact model, where the network status, including wireless link condition and nodal buffer availability, are jointly considered. The paper argues and proves that the nodal movement and the predicted collocation with the message recipient can serve as meaningful information to achieve an intelligent message forwarding decision at each node. The proposed protocol has been implemented and compared with a number of existing encounter-based routing approaches in terms of delivery delay, and the number of transmissions required for message delivery. The simulation results show that the proposed SAURP outperforms all the counterpart multi-copy encounter-based routing protocols considered in the study.

  4. Contention Aware Routing for Intermittently Connected Mobile Networks

    KAUST Repository

    Elwhishi, Ahmed

    2011-08-21

    This paper introduces a novel multi-copy routing protocol, called Self Adaptive Utility-based Routing Protocol (SAURP), for Delay Tolerant Networks (DTNs) that are possibly composed of a vast number of miniature devices such as smart phones, hand-held devices, and sensors mounted in fixed or mobile objects. SAURP aims to explore the possibility of taking mobile nodes as message carriers in order for end-to-end delivery of the messages. The best carrier for a message is determined by the prediction result using a novel contact model, where the network status, including wireless link condition and nodal buffer availability, are jointly considered. The paper argues and proves that the nodal movement and the predicted collocation with the message recipient can serve as meaningful information to achieve an intelligent message forwarding decision at each node. The proposed protocol has been implemented and compared with a number of existing encounter-based routing approaches in terms of delivery delay, and the number of transmissions required for message delivery. The simulation results show that the proposed SAURP outperforms all the counterpart multi-copy encounter-based routing protocols considered in the study.

  5. DRO: domain-based route optimization scheme for nested mobile networks

    Directory of Open Access Journals (Sweden)

    Chuang Ming-Chin

    2011-01-01

    Full Text Available Abstract The network mobility (NEMO basic support protocol is designed to support NEMO management, and to ensure communication continuity between nodes in mobile networks. However, in nested mobile networks, NEMO suffers from the pinball routing problem, which results in long packet transmission delays. To solve the problem, we propose a domain-based route optimization (DRO scheme that incorporates a domain-based network architecture and ad hoc routing protocols for route optimization. DRO also improves the intra-domain handoff performance, reduces the convergence time during route optimization, and avoids the out-of-sequence packet problem. A detailed performance analysis and simulations were conducted to evaluate the scheme. The results demonstrate that DRO outperforms existing mechanisms in terms of packet transmission delay (i.e., better route-optimization, intra-domain handoff latency, convergence time, and packet tunneling overhead.

  6. Effective ANT based Routing Algorithm for Data Replication in MANETs

    Directory of Open Access Journals (Sweden)

    N.J. Nithya Nandhini

    2013-12-01

    Full Text Available In mobile ad hoc network, the nodes often move and keep on change its topology. Data packets can be forwarded from one node to another on demand. To increase the data accessibility data are replicated at nodes and made as sharable to other nodes. Assuming that all mobile host cooperative to share their memory and allow forwarding the data packets. But in reality, all nodes do not share the resources for the benefits of others. These nodes may act selfishly to share memory and to forward the data packets. This paper focuses on selfishness of mobile nodes in replica allocation and routing protocol based on Ant colony algorithm to improve the efficiency. The Ant colony algorithm is used to reduce the overhead in the mobile network, so that it is more efficient to access the data than with other routing protocols. This result shows the efficiency of ant based routing algorithm in the replication allocation.

  7. Congestion control and routing over satellite networks

    Science.gov (United States)

    Cao, Jinhua

    Satellite networks and transmissions find their application in fields of computer communications, telephone communications, television broadcasting, transportation, space situational awareness systems and so on. This thesis mainly focuses on two networking issues affecting satellite networking: network congestion control and network routing optimization. Congestion, which leads to long queueing delays, packet losses or both, is a networking problem that has drawn the attention of many researchers. The goal of congestion control mechanisms is to ensure high bandwidth utilization while avoiding network congestion by regulating the rate at which traffic sources inject packets into a network. In this thesis, we propose a stable congestion controller using data-driven, safe switching control theory to improve the dynamic performance of satellite Transmission Control Protocol/Active Queue Management (TCP/AQM) networks. First, the stable region of the Proportional-Integral (PI) parameters for a nominal model is explored. Then, a PI controller, whose parameters are adaptively tuned by switching among members of a given candidate set, using observed plant data, is presented and compared with some classical AQM policy examples, such as Random Early Detection (RED) and fixed PI control. A new cost detectable switching law with an interval cost function switching algorithm, which improves the performance and also saves the computational cost, is developed and compared with a law commonly used in the switching control literature. Finite-gain stability of the system is proved. A fuzzy logic PI controller is incorporated as a special candidate to achieve good performance at all nominal points with the available set of candidate controllers. Simulations are presented to validate the theory. An effocient routing algorithm plays a key role in optimizing network resources. In this thesis, we briefly analyze Low Earth Orbit (LEO) satellite networks, review the Cross Entropy (CE

  8. Energy Efficient Link Aware Routing with Power Control in Wireless Ad Hoc Networks.

    Science.gov (United States)

    Katiravan, Jeevaa; Sylvia, D; Rao, D Srinivasa

    2015-01-01

    In wireless ad hoc networks, the traditional routing protocols make the route selection based on minimum distance between the nodes and the minimum number of hop counts. Most of the routing decisions do not consider the condition of the network such as link quality and residual energy of the nodes. Also, when a link failure occurs, a route discovery mechanism is initiated which incurs high routing overhead. If the broadcast nature and the spatial diversity of the wireless communication are utilized efficiently it becomes possible to achieve improvement in the performance of the wireless networks. In contrast to the traditional routing scheme which makes use of a predetermined route for packet transmission, such an opportunistic routing scheme defines a predefined forwarding candidate list formed by using single network metrics. In this paper, a protocol is proposed which uses multiple metrics such as residual energy and link quality for route selection and also includes a monitoring mechanism which initiates a route discovery for a poor link, thereby reducing the overhead involved and improving the throughput of the network while maintaining network connectivity. Power control is also implemented not only to save energy but also to improve the network performance. Using simulations, we show the performance improvement attained in the network in terms of packet delivery ratio, routing overhead, and residual energy of the network.

  9. Energy Efficient Link Aware Routing with Power Control in Wireless Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    Jeevaa Katiravan

    2015-01-01

    Full Text Available In wireless ad hoc networks, the traditional routing protocols make the route selection based on minimum distance between the nodes and the minimum number of hop counts. Most of the routing decisions do not consider the condition of the network such as link quality and residual energy of the nodes. Also, when a link failure occurs, a route discovery mechanism is initiated which incurs high routing overhead. If the broadcast nature and the spatial diversity of the wireless communication are utilized efficiently it becomes possible to achieve improvement in the performance of the wireless networks. In contrast to the traditional routing scheme which makes use of a predetermined route for packet transmission, such an opportunistic routing scheme defines a predefined forwarding candidate list formed by using single network metrics. In this paper, a protocol is proposed which uses multiple metrics such as residual energy and link quality for route selection and also includes a monitoring mechanism which initiates a route discovery for a poor link, thereby reducing the overhead involved and improving the throughput of the network while maintaining network connectivity. Power control is also implemented not only to save energy but also to improve the network performance. Using simulations, we show the performance improvement attained in the network in terms of packet delivery ratio, routing overhead, and residual energy of the network.

  10. Provisioning of adaptability to variable topologies for routing schemes in MANETs

    DEFF Research Database (Denmark)

    Jiang, Shengming; Liu, Yaoda; Jiang, Yuming

    2004-01-01

    .g., low, medium, and high mobility) have been proposed in the,literature. However, since a mobile node should not be limited to operate in a particular MANET assumed by-a routing scheme, an important issue is how to enable, a mobile node to achieve routing performance as high as possible when it roams...... in the dynamic source routing protocol to provide the adaptability to variable topologies caused by mobility through computer simulation in NS-2....

  11. Modeling and Performance Analysis of Route-Over and Mesh-Under Routing Schemes in 6LoWPAN under Error-Prone Channel Condition

    Directory of Open Access Journals (Sweden)

    Tsung-Han Lee

    2013-01-01

    Full Text Available 6LoWPAN technology has attracted extensive attention recently. It is because 6LoWPAN is one of Internet of Things standard and it adapts to IPv6 protocol stack over low-rate wireless personal area network, such as IEEE 802.15.4. One view is that IP architecture is not suitable for low-rate wireless personal area network. It is a challenge to implement the IPv6 protocol stack into IEEE 802.15.4 devices due to that the size of IPv6 packet is much larger than the maximum packet size of IEEE 802.15.4 in data link layer. In order to solve this problem, 6LoWPAN provides header compression to reduce the transmission overhead for IP packets. In addition, two selected routing schemes, mesh-under and route-over routing schemes, are also proposed in 6LoWPAN to forward IP fragmentations under IEEE 802.15.4 radio link. The distinction is based on which layer of the 6LoWPAN protocol stack is in charge of routing decisions. In route-over routing scheme, the routing distinction is taken at the network layer and, in mesh-under, is taken by the adaptation layer. Thus, the goal of this research is to understand the performance of two routing schemes in 6LoWPAN under error-prone channel condition.

  12. British Dance: Black Routes

    OpenAIRE

    Adair, C.; Burt, Ramsay, 1953-

    2016-01-01

    British Dance: Black Routes re-examines the distinctive contributions made to British dance by dancers who are Black. Covering the period 1946 to the present, it presents a radical re-reading of dancers and their companies, placing their achievements within a broader historical, cultural and artistic context. The result of a two year research project, British Dance and the African Diaspora, led by editors Christy Adair and Ramsay Burt, the collection looks at artists working with contempor...

  13. A model to improve the routing performance of Cognitive Radio Wireless Mesh Networks

    Directory of Open Access Journals (Sweden)

    Lesiba Morries Kola

    2017-12-01

    Full Text Available The increasing demand for broadband wireless technologies has led to the scarcity, inefficient utilization, and underutilization of the spectrum. The Cognitive Radio (CR technology has emerged as the promising solution which improves the utilization of the spectrum. However, routing is a challenge due to the dynamic nature of the CR networks. The link quality varies in space and time as nodes join and leave the network. The network connectivity is intermittent due to node mobility and the activities of the primary user. The spectrum aware, spectrum agile, and interference aware routing protocols are vital for the sturdiness of the network and efficient utilization of the resources. We propose an interference aware, spectrum aware, and agile extended Weighted Cumulative Expected Transmission Time (xWCETT routing protocol. The protocol integrates the features of the Ad-hoc On-demand Distance Vector (AODV and the weighted cumulative expected transmission time (WCETT routing protocols. The xWCETT was simulated using the Network Simulator 2 and its performance compared with the AODV and the WCETT routing protocols. The xWCETT was evaluated with respect to quality of service related metrics and the results show that it outperformed the AODV and WCETT routing protocols.

  14. Selective Route Based on SNR with Cross-Layer Scheme in Wireless Ad Hoc Network

    Directory of Open Access Journals (Sweden)

    Istikmal

    2017-01-01

    Full Text Available In this study, we developed network and throughput formulation models and proposed new method of the routing protocol algorithm with a cross-layer scheme based on signal-to-noise ratio (SNR. This method is an enhancement of routing protocol ad hoc on-demand distance vector (AODV. This proposed scheme uses selective route based on the SNR threshold in the reverse route mechanism. We developed AODV SNR-selective route (AODV SNR-SR for a mechanism better than AODV SNR, that is, the routing protocol that used average or sum of path SNR, and also better than AODV which is hop-count-based. We also used selective reverse route based on SNR mechanism, replacing the earlier method to avoid routing overhead. The simulation results show that AODV SNR-SR outperforms AODV SNR and AODV in terms of throughput, end-to-end delay, and routing overhead. This proposed method is expected to support Device-to-Device (D2D communications that are concerned with the quality of the channel awareness in the development of the future Fifth Generation (5G.

  15. Evaluación del punto de conmutación unicast- multicast para ahorro de potencia de transmisión en redes MBMS

    Directory of Open Access Journals (Sweden)

    Raúl Tamayo Fernández

    2014-01-01

    Full Text Available La oferta de aplicaciones y servicios multimedia para terminales móviles se hace principalmente a través de las redes celulares de tercera y cuarta generación (3G/4G existentes. El envío de los datos en este tipo de redes se realiza en modo unicast, es decir, a cada usuario se le dedican recursos de radio (ancho de banda y potencia de transmisión durante toda la sesión. Esto presenta algunos inconvenientes, tales como agotamiento rápido del ancho de banda del operador móvil, alto consumo de potencia de transmisión, incremento de la interferencia, y costos altos del servicio. Los operadores móviles requieren de nuevas tecnologías que optimicen el uso de sus recursos de radio y así lograr un mayor índice de penetración de los servicios. De ahí la necesidad de cambiar de paradigma hacia un modo de transmisión en multicast o broadcast, en el que una misma señal pueda recibirse por varios usuarios simultáneamente, de tal forma que los recursos de radio se puedan compartir. Para ello, la solución técnica sobre redes celulares LTE (Long Term Evolution se dio en la especificación 3GPP Release 6, llamada Servicio Multimedia por Broadcast/Multicast (MBMS, Multimedia Broadcast Multicast Service. La especificación de MBMS permite que una transmisión cambie de modo unicast a modo multicast a partir de un “punto de conmutación”, que determina el momento de hacer el cambio para obtener un ahorro tanto en ancho de banda como en potencia de transmisión. Este artículo presenta una evaluación para determinar los puntos de conmutación de modo de transmisión óptimos en el estándar MBMS para diferentes ambientes de propagación inalámbrica. Además, dado que MBMS se puede utilizar en topologías de Red de Frecuencia Única (SFN, Single Frequency Networks, que tienen la propiedad de “ganancia de red”, también se determina el ahorro de potencia de transmisión adicional que se obtiene en esta configuración.

  16. Analysis of pervasive mobile ad hoc routing protocols

    NARCIS (Netherlands)

    Qadri, N.N.; Liotta, A.; Hassanien, A.E.; Abawajy, J.H.; Abraham, A.; Hagras, H.

    2009-01-01

    Pervasive computing (also referred to as ubiquitous computing or ambient intelligence) aims to create environments where computers are invisibly and seamlessly integrated and connected into our everyday environment. Pervasive computing and intelligent multimedia technologies are becoming

  17. Performance Evaluation of a Routing Protocol in Wireless Sensor Network

    National Research Council Canada - National Science Library

    Cheng Kiat Amos, Teo

    2005-01-01

    ... and have topologies engineered. As such, recent research into wireless sensor networks has attracted great interest due to its diversity of applications, ranging in areas such as home, health, environmental and military applications...

  18. ING: INDOOR ROUTING PROTOCOL FOR GREEN HOME NETWORKS

    OpenAIRE

    Kaouthar Sethom; Nozha Al- Ibrahimi; Guy Pujolle

    2011-01-01

    Because of all the innovations in computer communications and digital consumer device technologies,people have had great interest in researching home networking systems. The home is evolving rapidlyinto a smart Mesh networked environment.Moreover, the energy consumption of wireless devices and networks gradually increases to represent asignificant portion of the operational cost, naturally also causing increased equivalent carbonemissions to the environment. Therefore, reducing the energy con...

  19. Reliable Internet Routing

    Science.gov (United States)

    2011-09-01

    global coordination. IEEE/ACM Trans. Netw., 9(6):681–692, 2001. [39] S. Goldberg, D. Xiao, E. Tromer, B. Barak , and J. Rexford. Path-quality monitoring...RFC 4271). [81] Y. Rekhter, T. Li, and S. Hares. A border gateway protocol 4 (BGP-4), 2006. IETF RFC 4271. [82] E. Rosen , A. Viswanathan, and R. Callon

  20. Robustness of airline route networks

    Science.gov (United States)

    Lordan, Oriol; Sallan, Jose M.; Escorihuela, Nuria; Gonzalez-Prieto, David

    2016-03-01

    Airlines shape their route network by defining their routes through supply and demand considerations, paying little attention to network performance indicators, such as network robustness. However, the collapse of an airline network can produce high financial costs for the airline and all its geographical area of influence. The aim of this study is to analyze the topology and robustness of the network route of airlines following Low Cost Carriers (LCCs) and Full Service Carriers (FSCs) business models. Results show that FSC hubs are more central than LCC bases in their route network. As a result, LCC route networks are more robust than FSC networks.

  1. In-memory interconnect protocol configuration registers

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Kevin Y.; Roberts, David A.

    2017-09-19

    Systems, apparatuses, and methods for moving the interconnect protocol configuration registers into the main memory space of a node. The region of memory used for storing the interconnect protocol configuration registers may also be made cacheable to reduce the latency of accesses to the interconnect protocol configuration registers. Interconnect protocol configuration registers which are used during a startup routine may be prefetched into the host's cache to make the startup routine more efficient. The interconnect protocol configuration registers for various interconnect protocols may include one or more of device capability tables, memory-side statistics (e.g., to support two-level memory data mapping decisions), advanced memory and interconnect features such as repair resources and routing tables, prefetching hints, error correcting code (ECC) bits, lists of device capabilities, set and store base address, capability, device ID, status, configuration, capabilities, and other settings.

  2. In-memory interconnect protocol configuration registers

    Science.gov (United States)

    Cheng, Kevin Y.; Roberts, David A.

    2017-09-19

    Systems, apparatuses, and methods for moving the interconnect protocol configuration registers into the main memory space of a node. The region of memory used for storing the interconnect protocol configuration registers may also be made cacheable to reduce the latency of accesses to the interconnect protocol configuration registers. Interconnect protocol configuration registers which are used during a startup routine may be prefetched into the host's cache to make the startup routine more efficient. The interconnect protocol configuration registers for various interconnect protocols may include one or more of device capability tables, memory-side statistics (e.g., to support two-level memory data mapping decisions), advanced memory and interconnect features such as repair resources and routing tables, prefetching hints, error correcting code (ECC) bits, lists of device capabilities, set and store base address, capability, device ID, status, configuration, capabilities, and other settings.

  3. Personal continuous route pattern mining

    Institute of Scientific and Technical Information of China (English)

    Qian YE; Ling CHEN; Gen-cai CHEN

    2009-01-01

    In the daily life, people often repeat regular routes in certain periods. In this paper, a mining system is developed to find the continuous route patterns of personal past trips. In order to count the diversity of personal moving status, the mining system employs the adaptive GPS data recording and five data filters to guarantee the clean trips data. The mining system uses a client/server architecture to protect personal privacy and to reduce the computational load. The server conducts the main mining procedure but with insufficient information to recover real personal routes. In order to improve the scalability of sequential pattern mining, a novel pattern mining algorithm, continuous route pattern mining (CRPM), is proposed. This algorithm can tolerate the different disturbances in real routes and extract the frequent patterns. Experimental results based on nine persons' trips show that CRPM can extract more than two times longer route patterns than the traditional route pattern mining algorithms.

  4. The extended TRIP supporting VoIP routing reservation with distributed QoS

    Science.gov (United States)

    Wang, Furong; Wu, Ye

    2004-04-01

    In this paper, an existing protocol, i.e. TRIP (Telephony Routing over IP) is developed to provide distributed QoS when making resource reservations for VoIP services such as H.323, SIP. Enhanced LSs (location servers) are deployed in ITADs (IP Telephony Administrative Domains) to take in charge of intra-domain routing policy because of small propagation price. It is an easy way to find an IP telephone route for intra-domain VoIP media association and simultaneously possess intra-domain load balancing features. For those routing reservations bridging domains, inter-domain routing policy is responsible for finding the shortest inter-domain route with enough resources. I propose the routing preference policy based on QoS price when the session traffic is shaped by a token bucket, related QoS messages, and message cooperation.

  5. Elisabeth Badinter, Fausse route

    OpenAIRE

    Martin-Juchat, Fabienne

    2013-01-01

    Elisabeth Badinter, philosophe de formation, est l’auteure de nombreux ouvrages sur la condition féminine et les rapports hommes/femmes dans la société. Avec Fausse route, elle signe une vision polémique du féminisme occidental. Son ouvrage a suscité de nombreuses critiques de femmes dans diverses revues destinées au grand public. Hélène Strohl, recenseur de la revue Culture en mouvement, conclut que cet ouvrage est peu scientifique, sujet à caution : « Argument contre argument, amalgame cont...

  6. An energy-aware engineered control plane for wavelength-routed networks

    DEFF Research Database (Denmark)

    Ricciardi, Sergio; Wang, Jiayuan; Palmieri, Francesco

    2015-01-01

    ' operational expenditures. To face this problem, we propose a single-stage routing and wavelength assignment scheme, based on several network engineering extensions to the Generalised Multi-Protocol Label Switching (GMPLS) control plane protocols, mainly Open Shortest Path First, with new composed metrics...

  7. PlayNCool: Opportunistic Network Coding for Local Optimization of Routing in Wireless Mesh Networks

    DEFF Research Database (Denmark)

    Pahlevani, Peyman; Roetter, Daniel Enrique Lucani; Pedersen, Morten Videbæk

    2013-01-01

    This paper introduces PlayNCool, an opportunistic protocol with local optimization based on network coding to increase the throughput of a wireless mesh network (WMN). PlayNCool aims to enhance current routing protocols by (i) allowing random linear network coding transmissions end-to-end, (ii) r...

  8. Routing Service Quality—Local Driver Behavior Versus Routing Services

    DEFF Research Database (Denmark)

    Ceikute, Vaida; Jensen, Christian S.

    2013-01-01

    of the quality of one kind of location-based service, namely routing services. Specifically, the paper presents a framework that enables the comparison of the routes provided by routing services with the actual driving behaviors of local drivers. Comparisons include route length, travel time, and also route...... popularity, which are enabled by common driving behaviors found in available trajectory data. The ability to evaluate the quality of routing services enables service providers to improve the quality of their services and enables users to identify the services that best serve their needs. The paper covers......Mobile location-based services is a very successful class of services that are being used frequently by users with GPS-enabled mobile devices such as smartphones. This paper presents a study of how to exploit GPS trajectory data, which is available in increasing volumes, for the assessment...

  9. Cryptographic Protocols:

    DEFF Research Database (Denmark)

    Geisler, Martin Joakim Bittel

    cryptography was thus concerned with message confidentiality and integrity. Modern cryptography cover a much wider range of subjects including the area of secure multiparty computation, which will be the main topic of this dissertation. Our first contribution is a new protocol for secure comparison, presented...... implemented the comparison protocol in Java and benchmarks show that is it highly competitive and practical. The biggest contribution of this dissertation is a general framework for secure multiparty computation. Instead of making new ad hoc implementations for each protocol, we want a single and extensible...... in Chapter 2. Comparisons play a key role in many systems such as online auctions and benchmarks — it is not unreasonable to say that when parties come together for a multiparty computation, it is because they want to make decisions that depend on private information. Decisions depend on comparisons. We have...

  10. 4 × 10 Gb s−1 wavelength multicasting with tunable NRZ-to-RZ format conversion using nonlinear polarization rotation in an SOA

    International Nuclear Information System (INIS)

    Liu, S; Fu, S; Tang, M; Shum, P; Liu, D

    2013-01-01

    We experimentally demonstrate simultaneous 4 × 10 Gb s −1 all-optical wavelength multicasting and non-return-to-zero (NRZ)-on-off-keying (OOK) to return-to-zero (RZ)-OOK format conversion with a tunable duty cycle using nonlinear polarization rotation in a semiconductor optical amplifier (SOA). The experimental results show that the duty cycle of four converted RZ-OOK signals can be tuned by adjusting the orientation of a polarizer placed at the SOA output. Four-channel NRZ-OOK-to-RZ-OOK conversion with a full width at half maximum of 33–67 ps can be simultaneously obtained with an extinction ratio over 10 dB. Moreover, it is experimentally verified that such a wavelength multicasting scheme with simultaneous NRZ-OOK-to-RZ-OOK conversion is insensitive to the wavelength of the input signal, indicating that such a scheme can be operated in the whole C-band with less than 0.18 dB power penalty at a bit error ratio level of 10 −9 . The device can facilitate the cross-connection between optical transmission networks employing different modulation formats. (paper)

  11. An Opportunistic Routing for Data Forwarding Based on Vehicle Mobility Association in Vehicular Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    Leilei Wang

    2017-11-01

    Full Text Available Vehicular ad hoc networks (VANETs have emerged as a new powerful technology for data transmission between vehicles. Efficient data transmission accompanied with low data delay plays an important role in selecting the ideal data forwarding path in VANETs. This paper proposes a new opportunity routing protocol for data forwarding based on vehicle mobility association (OVMA. With assistance from the vehicle mobility association, data can be forwarded without passing through many extra intermediate nodes. Besides, each vehicle carries the only replica information to record its associated vehicle information, so the routing decision can adapt to the vehicle densities. Simulation results show that the OVMA protocol can extend the network lifetime, improve the performance of data delivery ratio, and reduce the data delay and routing overhead when compared to the other well-known routing protocols.

  12. An overview of smart grid routing algorithms

    Science.gov (United States)

    Wang, Junsheng; OU, Qinghai; Shen, Haijuan

    2017-08-01

    This paper summarizes the typical routing algorithm in smart grid by analyzing the communication business and communication requirements of intelligent grid. Mainly from the two kinds of routing algorithm is analyzed, namely clustering routing algorithm and routing algorithm, analyzed the advantages and disadvantages of two kinds of typical routing algorithm in routing algorithm and applicability.

  13. Evaluation of RPL-compliant routing solutions in real-life WSNs

    Directory of Open Access Journals (Sweden)

    Zahariadis Theodore

    2016-01-01

    Full Text Available Wireless Sensor Networks (WSN applications continue to expand and already cover almost all our daily activities improving from security and environmental efficiency to gaming experience. The diverse applications running on top of WSNs have led to the design of an immense number of routing protocols. Few years ago, the IETF standardized the IPv6 routing protocol for low-power and lossy networks (RPL which is based on routing metrics to build communication paths between a source and the destination node. While significant efforts have focused on the design of routing metrics that satisfy the various applications, limited work has been reported on validating their performance using real-life motes. In this paper, we focus on validating the simulation results (obtained through the JSim simulator using TelosB motes for a set of routing metrics that have been proposed in our previous articles.

  14. Adaptive Relay Activation in the Network Coding Protocols

    DEFF Research Database (Denmark)

    Pahlevani, Peyman; Roetter, Daniel Enrique Lucani; Fitzek, Frank

    2015-01-01

    State-of-the-art Network coding based routing protocols exploit the link quality information to compute the transmission rate in the intermediate nodes. However, the link quality discovery protocols are usually inaccurate, and introduce overhead in wireless mesh networks. In this paper, we presen...

  15. Immunochemical protocols

    National Research Council Canada - National Science Library

    Pound, John D

    1998-01-01

    ... easy and important refinements often are not published. This much anticipated 2nd edition of Immunochemzcal Protocols therefore aims to provide a user-friendly up-to-date handbook of reliable techniques selected to suit the needs of molecular biologists. It covers the full breadth of the relevant established immunochemical methods, from protein blotting and immunoa...

  16. Vertex routing models

    International Nuclear Information System (INIS)

    Markovic, D; Gros, C

    2009-01-01

    A class of models describing the flow of information within networks via routing processes is proposed and investigated, concentrating on the effects of memory traces on the global properties. The long-term flow of information is governed by cyclic attractors, allowing to define a measure for the information centrality of a vertex given by the number of attractors passing through this vertex. We find the number of vertices having a nonzero information centrality to be extensive/subextensive for models with/without a memory trace in the thermodynamic limit. We evaluate the distribution of the number of cycles, of the cycle length and of the maximal basins of attraction, finding a complete scaling collapse in the thermodynamic limit for the latter. Possible implications of our results for the information flow in social networks are discussed.

  17. Southern states' routing agency report

    International Nuclear Information System (INIS)

    1989-02-01

    The Southern states' routing agency report is a compendium of 16-southern states' routing programs relative to the transportation of high-level radioactive materials. The report identifies the state-designated routing agencies as defined under 49 Code of Federal Regulations (CFR) Part 171 and provides a reference to the source ad scope of the agencies' rulemaking authority. Additionally, the state agency and contact designated by the state's governor to receive advance notification and shipment routing information under 10 CFR Parts 71 and 73 are also listed

  18. Southern States' Routing Agency Report

    International Nuclear Information System (INIS)

    1990-03-01

    The Southern States' Routing Agency Report is a compendium of 16-southern states' routing program for the transportation of high-level radioactive materials. The report identifies the state-designated routing agencies as defined under 49 Code of Federal Regulations (CFR) Part 171 and provides a reference to the source and scope of the agencies' rulemaking authority. Additionally, the state agency and contact designated by the state's governor to receive advance notification and shipment routing information under 10 CFR Parts 71 and 73 are also listed

  19. Secure Trust Based Key Management Routing Framework for Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Jugminder Kaur

    2016-01-01

    Full Text Available Security is always a major concern in wireless sensor networks (WSNs. Several trust based routing protocols are designed that play an important role in enhancing the performance of a wireless network. However they still have some disadvantages like limited energy resources, susceptibility to physical capture, and little protection against various attacks due to insecure wireless communication channels. This paper presents a secure trust based key management (STKF routing framework that establishes a secure trustworthy route depending upon the present and past node to node interactions. This route is then updated by isolating the malicious or compromised nodes from the route, if any, and a dedicated link is created between every pair of nodes in the selected route with the help of “q” composite random key predistribution scheme (RKPS to ensure data delivery from source to destination. The performance of trust aware secure routing framework (TSRF is compared with the proposed routing scheme. The results indicate that STKF provides an effective mechanism for finding out a secure route with better trustworthiness than TSRF which avoids the data dropping, thereby increasing the data delivery ratio. Also the distance required to reach the destination in the proposed protocol is less hence effectively utilizing the resources.

  20. A Cross-Layer Route Discovery Framework for Mobile Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    Wu Jieyi

    2005-01-01

    Full Text Available Most reactive routing protocols in MANETs employ a random delay between rebroadcasting route requests (RREQ in order to avoid "broadcast storms." However this can lead to problems such as "next hop racing" and "rebroadcast redundancy." In addition to this, existing routing protocols for MANETs usually take a single routing strategy for all flows. This may lead to inefficient use of resources. In this paper we propose a cross-layer route discovery framework (CRDF to address these problems by exploiting the cross-layer information. CRDF solves the above problems efficiently and enables a new technique: routing strategy automation (RoSAuto. RoSAuto refers to the technique that each source node automatically decides the routing strategy based on the application requirements and each intermediate node further adapts the routing strategy so that the network resource usage can be optimized. To demonstrate the effectiveness and the efficiency of CRDF, we design and evaluate a macrobian route discovery strategy under CRDF.