WorldWideScience

Sample records for multi hulled ships

  1. On the Global Ship Hull Bending Energy in Ship Collisions

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup; Li, Y.

    2004-01-01

    During ship collisions part of the kinetic energy of the involved vessels prior to contact is absorbed as energy dissipated by crushing of the hull structures, by friction and by elastic energy. The purpose of this report is to present an estimate of the elastic energy that can be stored in elastic...... hull vibrations during a ship collision. When a ship side is strengthened in order to improve the crashworthiness it has been argued in the scientific literature that a non trivial part of the energy released for structural deformation during the collision can be absorbed as elastic energy in global...... ship hull vibrations, such that with strong ship sides less energy has to be spent in crushing of the striking ship bow and/or the struck ship side. In normal ship-ship collision analyses both the striking and struck ship are usually considered as rigid bodies where structural crushing is confined...

  2. On the global ship hull bending energy in ship collisions

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup; Li, Yujie

    2009-01-01

    During ship collisions part of the kinetic energy of the involved vessels immediately prior to contact is absorbed as energy dissipated by crushing of the hull structures, by friction and by elastic energy. The purpose of this report is to present an estimate of the elastic energy that can...... be stored in elastic hull vibrations during a ship collision. When a ship side is strengthened in order to improve the crashworthiness it has been argued in the scientific literature that a non-trivial part of the energy released for structural deformation during the collision can be absorbed as elastic...... energy in global ship hull vibrations, such that with strong ship sides less energy has to be spent in crushing of the striking ship bow and/or the struck ship side. In normal ship–ship collision analyses both the striking and struck ship are usually considered as rigid bodies where structural crushing...

  3. Global Loads on FRP Ship Hulls

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup

    1997-01-01

    Fibre reinforced plastic (FRP) composites used for high-speed vessels have lower modulus of elasticity than the conventionally used steels.Therefore, for large fast ships the lowest natural frequencies of the global hull modes can be relatively low compared to the frequency of waveencounter....... As part of the NoKoS project it was decided to investigate the effect of hull flexibility on the wave-induced as well as accidental structural loads on high-speed ships.Especially it was decided to determine whether there is an upper size of FRP and aluminium mono-hulls caused by continuous wave action...

  4. Ultimate Strength of Ship Hulls under Torsion

    DEFF Research Database (Denmark)

    Paik, Jeom Kee; Thayamballi, Anil K.; Pedersen, Preben Terndrup

    2001-01-01

    For a ship hull with large deck openings such as container vessels and some large bulk carriers, the analysis of warping stresses and hatch opening deformations is an essential part of ship structural analyses. It is thus of importance to better understand the ultimate torsional strength characte......For a ship hull with large deck openings such as container vessels and some large bulk carriers, the analysis of warping stresses and hatch opening deformations is an essential part of ship structural analyses. It is thus of importance to better understand the ultimate torsional strength...... characteristics of ships with large hatch openings. The primary aim of the present study is to investigate the ultimate strength characteristics of ship hulls with large hatch openings under torsion. Axial (warping) as well as shear stresses are normally developed for thin-walled beams with open cross sections...... subjected to torsion. A procedure for calculating these stresses is briefly described. As an illustrative example, the distribution and magnitude of warping and shear stresses for a typical container vessel hull cross section under unit torsion is calculated by the procedure. By theoretical and numerical...

  5. Multi-purpose hull

    International Nuclear Information System (INIS)

    Taylor, W.C.; Horgan, J.B.G.; Downie, D.M.

    1982-01-01

    An 18 sided hull approximately 4 metres in diameter formed in prefabricated watertight sections from GRP has been designed for burying underground to withstand an overpressure of 12P.S.I above normal atmospheric pressure for human protection against a nuclear explosion and resultant radioactivity. The pre-fabricated sections are so designed to be stacked together prior to assembling and the assembled hulls can also be stacked together both vertically and horizontally in a honeycomb formation to form a multiple chamber. (author)

  6. Evaluation of Composite-Hull Ships Operating in Arctic Ice

    Science.gov (United States)

    2016-06-01

    COMPOSITE- HULL SHIPS OPERATING IN ARCTIC ICE by Ryan M. Tran June 2016 Thesis Advisor: Young W. Kwon Co-Advisor: Jarema M. Didoszak THIS...Master’s thesis 4. TITLE AND SUBTITLE EVALUATION OF COMPOSITE- HULL SHIPS OPERATING IN ARCTIC ICE 5. FUNDING NUMBERS 6. AUTHOR Ryan M. Tran 7...melting ice caps. Extensive research is thus being conducted to determine the interaction between ice and steel- hulls in anticipation of opening sea

  7. Diatom community structure on in-service cruise ship hulls.

    Science.gov (United States)

    Hunsucker, Kelli Zargiel; Koka, Abhishek; Lund, Geir; Swain, Geoffrey

    2014-10-01

    Diatoms are an important component of marine biofilms found on ship hulls. However, there are only a few published studies that describe the presence and abundance of diatoms on ships, and none that relate to modern ship hull coatings. This study investigated the diatom community structure on two in-service cruise ships with the same cruise cycles, one coated with an antifouling (AF) system (copper self-polishing copolymer) and the other coated with a silicone fouling-release (FR) system. Biofilm samples were collected during dry docking from representative areas of the ship and these provided information on the horizontal and vertical zonation of the hull, and intact and damaged coating and niche areas. Diatoms from the genera Achnanthes, Amphora and Navicula were the most common, regardless of horizontal ship zonation and coating type. Other genera were abundant, but their presence was more dependent on the ship zonation and coating type. Samples collected from damaged areas of the hull coating had a similar community composition to undamaged areas, but with higher diatom abundance. Diatom fouling on the niche areas differed from that of the surrounding ship hull and paralleled previous studies that investigated differences in diatom community structure on static and dynamically exposed coatings; niche areas were similar to static immersion and the hull to dynamic immersion. Additionally, diatom richness was greater on the ship with the FR coating, including the identification of several new genera to the biofouling literature, viz. Lampriscus and Thalassiophysa. These results are the first to describe diatom community composition on in-service ship hulls coated with a FR system. This class of coatings appears to have a larger diatom community compared to copper-based AF systems, with new diatom genera that have the ability to stick to ship hulls and withstand hydrodynamic forces, thus creating the potential for new problematic species in the biofilm.

  8. Ship with a double hull used to transport liquefied gases

    Energy Technology Data Exchange (ETDEWEB)

    1968-07-18

    A ship with a double hull is described which is used to transport liquefied gases in reservoirs which are held inside the inner hull by a glide support and surrounded by insulation. Troughs are situated at the bottom and along the adjacent ends of the side walls to catch leakage from the reservoirs. These catchers are made of a material which is tough when chilled. The catchers have a suction installation to remove the leaked fluid. (5 claims)

  9. Effect of stern hull shape on turning circle of ships

    Science.gov (United States)

    Jaswar, Maimun, A.; Wahid, M. A.; Priyanto, A.; Zamani, Pauzi, Saman

    2012-06-01

    Many factors such as: stern hull shape, length, draught, trim, propulsion system and external forces affecting the drift angle influence rate of turn and size of turning circle of ships. This paper discusses turning circle characteristics of U and V stern hull shape of Very Large Crude Oil Carrier (VLCC) ships. The ships have same principal dimension such as length, beam, and draught. The turning circle characteristics of the VLCC ships are simulated at 35 degree of rudder angle. In the analysis, firstly, turning circle performance of U-type VLCC ship is simulated. In the simulation, initial ship speed is determined using given power and rpm. Hydrodynamic derivatives coefficients are determined by including effect of fullness of aft run. Using the obtained, speed and hydrodynamic coefficients, force and moment acting on hull, force and moment induced by propeller, force and moment induced by rudder are determined. Finally, ship trajectory, ratio of speed, yaw angle and drift angle are determined. Results of simulation results of the VLCC ship are compared with the experimental one as validation. Using the same method, V-type VLCC is simulated and the simulation results are compared with U-type VLCC ship. Results shows the turning circle of U-type is larger than V-type due to effect stern hul results of simulation are.

  10. Wave-induced Ship Hull Vibrations in Stochastic Seaways

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher; Dogliani, M.

    1996-01-01

    A theoretical Study is undertaken on the determination of wave-induced loads in flexible ship hulls. The calculations are performed within the framework of a non-linear, quadratic strip theory formulated in the frequency domain. Included are non-linear effects due to changes in added mass......, hydrodynamic damping and water line breadth with sectional immersion in waves. The study is limited to continuous excitations from the waves and thus transient so-called whipping vibrations due to slamming loads are not considered.Because of the non-linearities the ship hull responses become non...... to the large separation between dominating wave frequencies and the lowest two-node frequency of the hull beam. Both extreme value predictions and fatigue damage are considered.For a fast container ship the rigid body and two-node (springing) vertical wave-induced bending moments amidship are calculated...

  11. Numerical Simulation of Galvanic Corrosion Caused by Shaft Grounding Systems in Steel Ship Hulls

    National Research Council Canada - National Science Library

    Wang, Y

    2005-01-01

    .... This led to the accelerated corrosion of the exposed steel ship hull on paint holidays because of the substantial difference of the electric potentials between the steel ship hull and the nickel...

  12. INTEGRATION OF SHIP HULL ASSEMBLY SEQUENCE PLANNING, SCHEDULING AND BUDGETING

    Directory of Open Access Journals (Sweden)

    Remigiusz Romuald Iwańkowicz

    2015-02-01

    Full Text Available The specificity of the yard work requires the particularly careful treatment of the issues of scheduling and budgeting in the production planning processes. The article presents the method of analysis of the assembly sequence taking into account the duration of individual activities and the demand for resources. A method of the critical path and resource budgeting were used. Modelling of the assembly was performed using the acyclic graphs. It has been shown that the assembly sequences can have very different feasible budget regions. The proposed model is applied to the assembly processes of large-scale welded structures, including the hulls of ships. The presented computational examples have a simulation character. They show the usefulness of the model and the possibility to use it in a variety of analyses.

  13. Grounding-Induced Sectional Forces and Residual Strength of Grounded Ship Hulls

    DEFF Research Database (Denmark)

    Paik, Jeom Kee; Pedersen, Preben Terndrup

    1996-01-01

    The aim of the present study is to determine the sectional forces induced by ship grounding and also to assess the residual strength of groundedship hulls. An analytical approach is used to estimate the grounding-induced sectional forces of ships. The extent and location of structural damage due...... to grounding is defined based on the ABS Safe Hull guide. The residual strength of damaged hulls is calculated by using a simple analytical formula. The method is applied to residual strength assessment of a damaged double hull tanker of 38,400 dwt due to grounding....

  14. A smart ROV solution for ship hull and harbor inspection

    Science.gov (United States)

    Reed, Scott; Wood, Jon; Vazquez, Jose; Mignotte, Pierre-Yves; Privat, Benjamin

    2010-04-01

    Hull and harbor infrastructure inspections are frequently performed manually and involve quite a bit of risk and human and monetary resources. In any kind of threat and resource constrained environment, this involves unacceptable levels of risk and cost. Modern Remotely Operated Vehicles are highly refined machines that provide features and capabilities previously unavailable. Operations once carried out by divers can now be carried out more quickly, efficiently and safely by smart enabled ROVs. ROVs are rapidly deployable and capable of continuous, reliable operations in adverse conditions. They also provide a stable platform on which multiple sensors may be mounted and utilized to meet the harbor inspection problem. Automated Control software provides ROV's and their pilots with the capability to inspect complex, constrained environments such as those found in a harbor region. This application and the user interface allow the ROV to automatically conduct complex maneuvers relative to the area being inspected and relieves the training requirements and work load for the pilot, allowing he or she to focus on the primary task of survey, inspection and looking for possible threats (such as IEDs, Limpet Mines, signs of sabotage, etc). Real-time sensor processing tools can be integrated into the smart ROV solution to assist the operator. Automatic Target Recognition (ATR) algorithms are used to search through the sensor data collected by the ROV in real time. These algorithms provide immediate feedback on possible threats and notify the operator of regions that may require manual verification. Sensor data (sonar or video) is also mosaiced, providing the operator with real-time situational awareness and a coverage map of the hull or seafloor. Detected objects may also be placed in the context of the large scale characteristics of the hull (or bottom or pilings) and localized. Within the complex areas such as the harbor pier pilings and the running gear of the ship, real

  15. Numerical Simulation of Galvanic Corrosion Caused by Shaft Grounding Systems in Steel Ship Hulls

    National Research Council Canada - National Science Library

    Wang, Y

    2005-01-01

    The shaft grounding systems used on board HMC ships have substantially reduced the shaft-to-hull resistance and, thus, improved the performance of the shipboard impressed current cathodic protection (ICCP) system...

  16. Automated Visual Inspection of Ship Hull Surfaces Using the Wavelet Transform

    Directory of Open Access Journals (Sweden)

    Carlos Fernández-Isla

    2013-01-01

    Full Text Available A new online visual inspection technique is proposed, based on a wavelet reconstruction scheme over images obtained from the hull. This type of visual inspection to detect defects in hull surfaces is commonly carried out at shipyards by human inspectors before the hull repair task starts. We propose the use of Shannon entropy for automatic selection of the band for image reconstruction which provides a low decomposition level, thus avoiding excessive degradation of the image, allowing more precise defect segmentation. The proposed method here is capable of on-line assisting to a robotic system to perform grit blasting operations over damage areas of ship hulls. This solution allows a reliable and cost-effective operation for hull grit spot blasting. A prototype of the automated blasting system has been developed and tested in the Spanish NAVANTIA shipyards.

  17. Ship hull fouling in the port of Recife, Pernambuco

    Directory of Open Access Journals (Sweden)

    Cristiane Maria Rocha Farrapeira

    2007-09-01

    Full Text Available Ports of big coastal cities are exposed to exotic species as a consequence of shipping traffic. As the Port of Recife receives an annual average of 491 ships from other regions of Brazil and from all over the world, this work was aimed at knowing which marine animals were passively transported on such vessels hulls, in order to map and monitor new bioinvasions in the area. Thus, 32 vessels of several origins were investigated between November 2005 and March 2006, samples were taken and the macrofauna identified. Sixty species of associated animals were identified, consisting of 28 sessile species, particularly the Cirripedia Balanomorpha and Lepadomorpha as dominants, 8 sedentary animals, namely Mytillidae and Dreissenidae and 23 free-living species, particularly, Caprellidae, Gammaridae, Tanaidacea, Turbellaria, Nemertea and Polychaeta. The first occurrence of Conchoderma virgatum was recorded with exact location for the Brazilian littoral, and Conchoderma auritum, Amphibalanus subalbidus and Haliplanella lineata were recorded for the first time at the littoral of Pernambuco State. The invasion pathway was confirmed for Amphibalanus reticulatus and Mytilopsis leucophaeta, invader species of the estuarine area of Recife's city. Megabalanus coccopoma was considered as a risk invader species for the region.Regiões portuárias das grandes cidades litorâneas estão sujeitas à recepção de espécies exóticas como conseqüência da movimentação dos navios. Como o Porto do Recife recebe uma média anual de 491 atracações de navios, provenientes de várias regiões do Brasil e do mundo, objetivou-se conhecer quais animais marinhos eram transportados passivamente nos cascos das embarcações para mapear e monitorar novas invasões biológicas na área. Assim, foram investigados 32 barcos de diversas origens, nos meses de novembro de 2005 a março de 2006, tendo a macrofauna sido amostrada e identificada. Foram encontradas 60 espécies de animais

  18. Drag resistance measurements for newly applied antifouling coatings and welding seams on ship hull surface

    DEFF Research Database (Denmark)

    Wang, Xueting; Olsen, S. M.; Andres, E.

    Drag resistances of newly applied antifouling coatings and welding seams on ship hull surface have been investigated using a pilot-scale rotary setup. Both conventional biocide-based antifouling (AF) coatings and silicone-based fouling release (FR) coatings have been studied and compared in their......Drag resistances of newly applied antifouling coatings and welding seams on ship hull surface have been investigated using a pilot-scale rotary setup. Both conventional biocide-based antifouling (AF) coatings and silicone-based fouling release (FR) coatings have been studied and compared...

  19. Acoustic emission localization on ship hull structures using a deep learning approach

    DEFF Research Database (Denmark)

    Georgoulas, George; Kappatos, Vassilios; Nikolakopoulos, George

    2016-01-01

    In this paper, deep belief networks were used for localization of acoustic emission events on ship hull structures. In order to avoid complex and time consuming implementations, the proposed approach uses a simple feature extraction module, which significantly reduces the extremely high dimension......In this paper, deep belief networks were used for localization of acoustic emission events on ship hull structures. In order to avoid complex and time consuming implementations, the proposed approach uses a simple feature extraction module, which significantly reduces the extremely high...

  20. The Assessment of the Ultimate Hull Girder Strength of RO-RO Ship after Damages

    Science.gov (United States)

    Zubair Muis Alie, Muhammad; Sitepu, Ganding; Izaak Latumahin, Samuel

    2018-03-01

    Many accidents of Ro-Ro ships happen in Indonesia such as collision and grounding. When the collision or grounding takes place on the Ro-Ro ship, the ultimate strength of hull structure after damage becomes decrease. Car and passenger decks are critical location since collision and/or grounding occur. In the present study, the assessment of the ultimate hull girder strength is conducted. The cross section of Ro-Ro ship is taken to be analyzed. The collision and grounding damages are assumed to be palced on the side and bottom area, respectively. The damages are created by removing the element from the side shell and bottom part. Finally, the result obtained is compared with one another.

  1. Report of the Committee on the Survey of Hull Bottom of Nuclear Ship Mutsu

    International Nuclear Information System (INIS)

    1979-01-01

    The nuclear ship Mutsu arrived the Sasebo Shipyard, Sasebo Heavy Industries Co., Ltd., in October, 1978, to repair the shielding for the reactor and to inspect generally the safety. The docking works were not carried out since 1972 for the Mutsu, therefore it was decided to admit the Mutsu in a dock to put the hull in order. To prepare for starting the output test again, it is necessary to grasp the state of the hull part below water line and take appropriate measures as occasions demand, therefore the Japan Nuclear Ship Development Agency established the Committee on the Survey of Hull Bottom of Nuclear Ship Mutsu in July, 1979. Three meetings of the committee were held from July 2 to September 19, and the draft of the report was drawn up. The Mutsu entered No. 5 dock of the Sasebo Shipyard on July 9, and left on July 23, and the survey of the hull bottom was carried out during that period. The results of the survey are reported as follows: the state of bottom shell plates, the state of aft part and the propeller, the state of sea chests, the state of the electrical corrosion protection of bottom shell plates and the state of sea valves. The problem to be specially mentioned was not found, and it was recognized that the sound maintenance has been carried out. (Kako, I.)

  2. The Effect of Hull Biofouling on Parameters Characterising Ship Propulsion System Efficiency

    Directory of Open Access Journals (Sweden)

    Tarełko Wiesła

    2015-01-01

    Full Text Available One of most important issues concerning technical objects is the increase of their operating performance. For a ship this performance mainly depends on the efficiency of its main pro-pulsion system and the resistance generated during its motion on water. The overall ship re-sistance, in turn, mainly depends on the hull friction resistance, closely related with the pres-ence of different types of roughness on the hull surface, including underwater part biofouling. The article analyses the effect of hull biofouling on selected parameters characterising the efficiency of the ship propulsion system with adjustable propeller. For this purpose a two-year research experiment was performed on a sailing vessel during its motor navigation phases. Based on the obtained results, three groups of characteristics were worked out for different combinations of engine rotational speed and adjustable propeller pitch settings. The obtained results have revealed that the phenomenon of underwater hull biofouling affects remarkably the parameters characterising propulsion system efficiency. In particular, the development of the biofouling layer leads to significant reduction of the speed of navigation.

  3. Maintained ship hull girder ultimate strength reliability considering corrosion and fatigue

    DEFF Research Database (Denmark)

    Hu, Yong; Cui, W.; Pedersen, Preben Terndrup

    2004-01-01

    The prupose of this paper is to propose a methodology to assess the time-variant ultimate strength of ship hull girder under the degradations of corrosion and fatigue. The effects of fatigue cracks on the tensile and compressive residual ultimate strength of stiffened panels and unstiffened plates......, webs and flanges, respectively. The effects of inspections and repair are taken into account. A minimum net thickness rule is used to determine repair policies. A procedure is proposed to determine the maximum allowable corrosion thickness of different parts of the hull cross section. The procedure...

  4. Effects of biofouling development on drag forces of hull coatings for ocean-going ships: a review

    DEFF Research Database (Denmark)

    Lindholdt, Asger; Dam-Johansen, Kim; Olsen, S. M.

    2015-01-01

    This review presents a systematic overview of the literature and describes the experimental methods used to quantify the drag of hull coatings. It also summarizes the findings of hull coating's drag performance and identifies the main parameters impacting it. The advantages and disadvantages...... of the reported methods listed in this review provide an assessment of the most efficient methods to quantify the drag performance of hull coatings. This review determines that drag performance of hull coating technology varies depending on whether the coating condition is newly applied, after dynamic or static...... seawater exposure. The summarized data reveal that, while several methods have attempted to quantify drag performance of hull coatings, other methods must be explored in order to accurately measure the long-term drag performance of hull coatings in conditions mimicking those that ship hulls encounter...

  5. Turbulence modeling of transverse flow on ship hulls in shallow water

    Energy Technology Data Exchange (ETDEWEB)

    Jakobsen, Ken-Robert Gjelstad

    2010-09-15

    The hydrodynamic forces acting on a ship that travels in restricted water vary greatly with water depth and the geometry of the ship hull. This will affect the ship maneuverability in terms of various flow effects like for instance squat, when the ship is sucked down towards the seabed due to a pressure drop on the hull at forward speed. It is, thus, important to gain detailed knowledge on these aspects of marine engineering. The problem is in the present work addressed through a numerical investigation of turbulent transverse flow on two-dimensional ship sections in shallow water. The numerical code is validated against traditional flow problems in the literature. Namely, the Backward-facing step (BFS) and the Smoothly-contoured ramp (SCR). 2D and 3D laminar flows and 2D low Reynolds number turbulent flows are calculated, and the results are found to be in good agreement with the previous numerical and experimental comparison data. The turbulence model used in the calculations is the one-equation Spalart-Allmaras model. The overall goal of achieving more efficient and accurate numerical schemes will always be in focus of code development. Adaptive mesh refinement (AMR) is then a very helpful tool to save both time for grid generation prior to the calculations in question and the CPU hours needed to solve the governing equations. The latter is even more evident in a parallel environment. These aspects are included in the present investigation as part of the process to adapt and investigate a CFD tool suitable to handle turbulent flows on a ship hull in shallow water. Several physical and numerical parameters are included in the present study and the Plackett-Burman screening design is utilized to efficiently analyze the results. With the latter method, a simple function for calculating the drag force on a two-dimensional ship section as function of the given parameters has been obtained. (Author)

  6. Effect of ship hull form on the resistance penalty from biofouling.

    Science.gov (United States)

    Oliveira, Dinis; Larsson, Ann I; Granhag, Lena

    2018-03-01

    Hull biofouling is a well-known problem for the shipping industry, leading to increased resistance and fuel consumption. Considering that the effects of hull form on resistance are known to be higher for a less slender hull, it is hypothesised in this paper that the effect of biofouling roughness on resistance is also dependent on the hull form. To test this hypothesis, previously reported full-scale numerical results on a containership are re-analysed. Form effects on roughness penalties, corresponding to K ΔCT  = 0.058 ± 0.025, are observed at a low speed (19 knots, Re s  = 2.29 × 10 9 ), which are however cancelled out by traditionally neglected roughness effects on wave-making resistance at a higher speed (24 knots, Re s  = 2.89 × 10 9 ). It is concluded that hull form effects on biofouling penalties can be significant at low speeds, though not generalisable for higher speeds, namely when wave-making resistance corresponds to ≥ 29% of total resistance.

  7. Experimental Study of Thermoelectric Generator as Electrical Source of Impressed Current Cathodic Protection for Ship Hull

    Directory of Open Access Journals (Sweden)

    Adi Kurniawan

    2017-06-01

    Full Text Available Impressed Current Cathodic Protection (ICCP is a method to protect metallic material such as ship hull from corrosion by using electric current. In this research, a prototype of thermoelectric generator is developed in order to supply the ICCP system. This thermoelectric generator is planned to utilize the exhaust gas from main engine of the ship. Method carried in this research is assembling the prototype of thermoelectric generator followed by conducted experiment to observe the potential energy of the prototype. After that, the required number of thermoelectric generator is calculated to supply the ICCP system to protect the ship from corrosion. The object in this research is live fish carrier “Wellboat” which has 396.08 m2 wetted area. The required voltage and current to protect the ship from corrosion for three years are 16.67 Volt and 2.66 Ampere. Based on the experiment, a prototype of thermoelectric generator can generate 0.34 Ampere and 4.43 Volt, causing the need of 8 series and 4 parallels connection. It can be concluded that the corrosion rate on the ship hull can be decelerated by using impressed current cathodic protection method without needing additional cost or fuel consumption to produce electric energy.  

  8. Experimental and Numerical Analysis of Hull Girder Vibrations and Bow Impact of a Large Ship Sailing in Waves

    Directory of Open Access Journals (Sweden)

    Jialong Jiao

    2015-01-01

    Full Text Available It is of great importance to evaluate the hull structural vibrations response of large ships in extreme seas. Studies of hydroelastic response of an ultra large ship have been conducted with comparative verification between experimental and numerical methods in order to estimate the wave loads response considering hull vibration and water impact. A segmented self-propelling model with steel backbone system was elaborately designed and the experiments were performed in a tank. Time domain numerical simulations of the ship were carried out by using three-dimensional nonlinear hydroelasticity theory. The results from the computational analyses have been correlated with those from model tests.

  9. A study on antifouling technique through seawater electrolyzing reaction on ship hull surface 【Article】

    OpenAIRE

    Huang, Yi; Saito, Kimio; Usami, Masahiro

    2003-01-01

    The antifouling technique through seawater electrolysis for ship hulls may be realized by an antifoul-ing system consisting of a power unit and the electro-conductive film. In the electric field formed bysuch an antifouling system, besides that both the electro-conductive film layer sub-region and the sea-water sub-region are included, polarization occurs on the interface between electro-conductive film layerand seawater. Therefore, based on the Interface Electro-Double Layer theory, a numeri...

  10. Lead sheathing of ship hulls in the Roman period: Archaeometallurgical characterisation

    Energy Technology Data Exchange (ETDEWEB)

    Kahanov, Yaacov, E-mail: yak@research.haifa.ac.il [Leon Recanati Institute for Maritime Studies, University of Haifa, Haifa 31905 (Israel); Ashkenazi, Dana [Faculty of Engineering, Tel Aviv University, Ramat Aviv 69978 (Israel)

    2011-08-15

    An archaeometallurgical analysis of samples of lead sheathing from five ships of the Roman period was carried out in order to determine their composition and microstructure, and to obtain a better understanding of their manufacturing processes. The examinations included optical microscopy of metallographic cross-sections, microhardness tests, scanning electron microscopy, including energy dispersive spectroscopy, and X-ray photoelectron spectroscopy. The results show that the samples were all composed of lead covered with an oxide layer. The sheet thicknesses, microhardness values and microhardness distribution, as well as the grain size distribution, led to the conclusion that all of the sheets were produced by the same technology, using hammering, and were probably used for the same purpose. The presence of antimony was observed in the sample from the Roman ship from Caesarea, which may hint at an Italian (Sardinian) origin of the material, and perhaps of the ship. - Research Highlights: {yields} During the Roman period ship hulls were sheathed with lead. {yields} Five samples have been analysed for their characteristics and manufacturing process. {yields} The process was cold-working (strain-hardening) using hammering. {yields} The lead was open-casted on a flat stone, and later hammered at room temperature. {yields} Antimony in the Caesarea shipwreck may indicate an Italian origin of construction.

  11. Static vs dynamic settlement and adhesion of diatoms to ship hull coatings.

    Science.gov (United States)

    Zargiel, Kelli A; Swain, Geoffrey W

    2014-01-01

    Many experiments utilize static immersion tests to evaluate the performance of ship hull coatings. These provide valuable data; however, they do not accurately represent the conditions both the hull and fouling organisms encounter while a ship is underway. This study investigated the effect of static and dynamic immersion on the adhesion and settlement of diatoms to one antifouling coating (BRA 640), four fouling-release coatings (Intersleek(®) 700, Intersleek(®) 900, Hempasil X3, and Dow Corning 3140) and one standard surface (Intergard(®) 240 Epoxy). Differences in community composition were observed between the static and dynamic treatments. Achnanthes longipes was present on all coatings under static immersion, but was not present under dynamic immersion. This was also found for diatoms in the genera Bacillaria and Gyrosigma. Melosira moniformis was the only diatom present under dynamic conditions, but not static conditions. Several common fouling diatom genera were present on panels regardless of treatment: Amphora, Cocconeis, Entomoneis Cylindrotheca, Licmophora, Navicula, Nitzschia, Plagiotropis, and Synedra. Biofilm adhesion, diatom abundance and diatom diversity were found to be significantly different between static and dynamic treatments; however, the difference was dependent on coating and sampling date. Several coatings (Epoxy, DC 3140 and IS 700) had significantly higher biofilm adhesion on dynamically treated panels on at least one of the four sampling dates, while all coatings had significantly higher diatom abundance on at least one sampling date. Diversity was significantly greater on static panels than dynamic panels for Epoxy, IS 700 and HX3 at least once during the sampling period. The results demonstrate how hydrodynamic stress will significantly influence the microfouling community. Dynamic immersion testing is required to fully understand how antifouling surfaces will respond to biofilm formation when subjected to the stresses experienced

  12. Residual Strength Analysisof Asymmetrically Damaged Ship Hull GirderUsing Beam Finite Element Method

    Directory of Open Access Journals (Sweden)

    Muhammad Zubair Muis Alie

    2016-04-01

    Full Text Available The objective of the present study is to analyze the residual strength of asymmetrically damaged ship hull girder under longitudinal bending. Beam Finite Element Method isused for the assessment of the residual strength of two single hull bulk carriers (Ship B1 and Ship B4 and a three-cargo-hold model of a single-side Panamax Bulk Carrierin hogging and sagging conditions. The Smith’s  method  is  adopted  and  implemented  into  Beam  Finite  Element Method. An efficient solution procedure is applied; i.e. by assuming the cross section remains plane, the vertical bending moment is applied to the  cross section  and  three-cargo-hold  model. As a fundamental  case,  the  damage is simply  created  by removing the elements from the cross section, neglecting any welding residual stress and initial imperfection. Also no crack  extension  is considered.  The  result  obtained  by  Beam  Finite  Element  Method  so-called Beam-HULLST is compared to the progressive collapse analysis obtained by HULLST for the validation of the present work. Then, for the three-hold-model, the Beam-HULLST is used to investigate the effect of the rotation of the netral axisboth intact and damage condition taking the one and five frame spaces into account. 

  13. Preliminary Investigations of Biofouling of ShipsHulls: Non-Indigenous Species Investigations in the Columbia River

    Science.gov (United States)

    2006-04-01

    around the world are numerous; they include biocontrol introductions, ornamental escapes, deliberate and accidental introductions associated with...mollusks, nematodes , protozoans and sponges (Ruiz et al., 2000; Fofonoff et al., 2003). As a sub-vector of shipping, hull fouling is known to be... biocontrol , wildlife enhancement, and individual releases (Sytsma et al., 2004). For invertebrates, the most dominant vector was shipping with 85 percent

  14. Optimum Position of Acoustic Emission Sensors for Ship Hull Structural Health Monitoring Based on Deep Machine Learning

    DEFF Research Database (Denmark)

    Kappatos, Vassilios; Karvelis, Petros; Georgoulas, George

    2018-01-01

    In this paper a method for the estimation of the optimum sensor positions for acoustic emission localization on ship hull structures is presented. The optimum sensor positions are treated as a classification (localization) problem based on a deep learning paradigm. In order to avoid complex...

  15. A new improved artificial bee colony algorithm for ship hull form optimization

    Science.gov (United States)

    Huang, Fuxin; Wang, Lijue; Yang, Chi

    2016-04-01

    The artificial bee colony (ABC) algorithm is a relatively new swarm intelligence-based optimization algorithm. Its simplicity of implementation, relatively few parameter settings and promising optimization capability make it widely used in different fields. However, it has problems of slow convergence due to its solution search equation. Here, a new solution search equation based on a combination of the elite solution pool and the block perturbation scheme is proposed to improve the performance of the algorithm. In addition, two different solution search equations are used by employed bees and onlooker bees to balance the exploration and exploitation of the algorithm. The developed algorithm is validated by a set of well-known numerical benchmark functions. It is then applied to optimize two ship hull forms with minimum resistance. The tested results show that the proposed new improved ABC algorithm can outperform the ABC algorithm in most of the tested problems.

  16. Ship

    OpenAIRE

    Keuning, J.A.

    2008-01-01

    The invention concerns a ship designed for use at high speed and heavy seas having a single long and slender hull with a narrow beam and a more or less vertical bow, whereby the front half of the hull has more or less vertical sides, minimal flare in the bow sections and towards the bow an increase in draught at its center line combined with a more or less similar increase of freeboard and whereby the aft end of the hull has a flat or slightly V-shaped bottom with one or more propellers and/o...

  17. Hull-Mounted Acoustic Doppler Current Profiler Data (SADCP) collected aboard the NOAA Ship NANCY FOSTER during cruise NF-10-01 and NF-10-02

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Upper ocean current velocity measurements collected with NOAA Ship NANCY FOSTER's Teledyne RD Instruments 150 kHz hull-mounted acoustic Doppler current profiler...

  18. CFD investigation of pentamaran ship model with chine hull form on the resistance characteristics

    Science.gov (United States)

    Yanuar; Sulistyawati, W.

    2018-03-01

    This paper presents an investigation of pentamaran hull form with chine hull form to the effects of outriggers position, asymmetry, and deadrise angles on the resistance characteristics. The investigation to the resistance characteristics by modelling pentamaran hull form using chine with symmetrical main hull and asymmetric outboard on the variation deadrise angles: 25°, 30°, 35° and Froude number 0,1 to 0,7. On calm water resistance characteristics of six pentamaran models with chine-hull form examined by variation of deadrise angles by using CFD. Comparation with Wigley hull form, the maximum resistance drag reduction of the chine hull form was reduced by 15.81% on deadrise 25°, 13.8% on deadrise 30°, and 20.38% on deadrise 35°. While the smallest value of total resistance coefficient was generated from chine 35° at R/L:1/14 and R/L:1/7. Optimum hull form for minimum resistance has been obtained, so it is interesting to continue with angle of entrance and stem angle of hull for further research.

  19. Shipping

    NARCIS (Netherlands)

    Wijnolst, N.; Wergeland, T.

    1996-01-01

    Shipping is a multi-faceted industry which is rather complex to define from an academic point of view. This book attempts to grasp these complexities and provide the reader with an overview of the main topics and terminology in shipping. The book is based on material from our courses in shipping at

  20. Acoustical characteristic predictions of a multi-layer system of a submerged vehicle hull mounted sonar simplified to an infinite planar model

    Directory of Open Access Journals (Sweden)

    Sung-Hee Kim

    2012-06-01

    Full Text Available Hull Mounted Sonar (HMS is a long range submerged vehicle's hull-mounted passive sonar system which detects low-frequency noise caused by machineries of enemy ships or submerged vehicles. The HMS needs a sound absorption /insulation multi-layer structure to shut out the self-noise from own machineries and to amplify signals from outside. Therefore, acoustic analysis of the multi-layer system should be performed when the HMS is designed. This paper simplified the HMS multi-layer system to be an infinite planar multi-layer model. Also, main excitations that influence the HMS were classified into mechanical, plane wave and turbulent flow excitation, and the investigations for each excitation were performed for various models. Stiffened multi-layer analysis for mechanical excitation and general multi-layer analysis for turbulent flow excitation were developed. The infinite planar multi-layer analysis was expected to be more useful for preliminary design stage of HMS system than the infinite cylindrical model because of short analysis time and easiness of parameter study.

  1. Convex hull ranking algorithm for multi-objective evolutionary algorithms

    NARCIS (Netherlands)

    Davoodi Monfrared, M.; Mohades, A.; Rezaei, J.

    2012-01-01

    Due to many applications of multi-objective evolutionary algorithms in real world optimization problems, several studies have been done to improve these algorithms in recent years. Since most multi-objective evolutionary algorithms are based on the non-dominated principle, and their complexity

  2. Costs and benefits to European shipping of ballast-water and hull-fouling treatment

    NARCIS (Netherlands)

    Fernandes, Jose A.; Santos, Lionel; Vance, Thomas; Fileman, Tim; Smith, David; Bishop, John D.D.; Viard, Frédérique; Queirós, Ana M.; Merino, Gorka; Buisman, Erik; Austen, Melanie C.

    2016-01-01

    Maritime transport and shipping are impacted negatively by biofouling, which can result in increased fuel consumption. Thus, costs for fouling reduction can be considered an investment to reduce fuel consumption. Anti-fouling measures also reduce the rate of introduction of non-indigenous species

  3. Safety guidelines of ultimate hull girder strength for grounded container ships

    DEFF Research Database (Denmark)

    Kim, Do Kyun; Pedersen, Preben Terndrup; Paik, Jeom Kee

    2013-01-01

    Various accidents commonly occur on operating ships. The structural damage caused by such accidents is often accompanied by casualties and serious pollution. In this regard, an accidental risk-based approach that is in line with the Goal Based Standard (GBS) of the International Maritime Organiza...

  4. Drag resistance of ship hulls: Effects of surface roughness of newly applied fouling control coatings, coating water absorption, and welding seams

    DEFF Research Database (Denmark)

    Wang, Xueting; Olsen, Stefan Møller; Andrés, Eduardo

    2018-01-01

    selected, that a so-called fouling release (FR) coating caused approximately 5.6 % less skin friction (torque) over time than traditional biocide-based antifouling (AF) coatings at a tangential speed of 12 knots. Furthermore, results of immersion experiments and supporting “standard” water absorption......Fouling control coatings (FCCs) and irregularities (e.g. welding seams) on ship hull surfaces have significant effects on the overall drag performance of ships. In this work, skin frictions of four newly applied FCCs were compared using a pilot-scale rotary setup. Particular attention was given...

  5. Experimental investigation of frictional resistance reduction with air layer on the hull bottom of a ship

    Directory of Open Access Journals (Sweden)

    Jang Jinho

    2014-06-01

    Full Text Available In an effort to cope with recent high oil price and global warming, developments of air lubricated ships have been pursued to reduce greenhouse gas emissions and to save fuel costs by reducing the frictional resistance. In this study, reduction in the frictional resistance by air lubrication with air layers generated on the lower surface of a flat plate was investigated experimentally in the large water tunnel of SSMB. The generated air layers were observed, and changes in the local frictional drag were measured at various flow rates of injected air. The results indicated that air lubrication with air layers might be useful in reducing the frictional resistance at specific conditions of air injection. Accordingly, resistance and self-propulsion tests for a 66K DWT bulk carrier were carried out in the towing tank of SSMB to estimate the expected net power savings.

  6. 46 CFR 45.129 - Hull fittings: General.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Hull fittings: General. 45.129 Section 45.129 Shipping... Assignment § 45.129 Hull fittings: General. Hull fittings must be securely mounted in the hull so as to avoid increases in hull stresses and must be protected from local damage caused by movement of equipment or cargo. ...

  7. A Fiber-Optic Tether for the Hull Search UUV System Documentation

    National Research Council Canada - National Science Library

    Buescher, J. G

    2006-01-01

    ...) conducting ship hull inspection missions, defines the required specifications that will allow the integration and installation of a FO tether system on UUVs with ship hull inspection capability...

  8. Assessment regarding the use of the computer aided analytical models in the calculus of the general strength of a ship hull

    Science.gov (United States)

    Hreniuc, V.; Hreniuc, A.; Pescaru, A.

    2017-08-01

    Solving a general strength problem of a ship hull may be done using analytical approaches which are useful to deduce the buoyancy forces distribution, the weighting forces distribution along the hull and the geometrical characteristics of the sections. These data are used to draw the free body diagrams and to compute the stresses. The general strength problems require a large amount of calculi, therefore it is interesting how a computer may be used to solve such problems. Using computer programming an engineer may conceive software instruments based on analytical approaches. However, before developing the computer code the research topic must be thoroughly analysed, in this way being reached a meta-level of understanding of the problem. The following stage is to conceive an appropriate development strategy of the original software instruments useful for the rapid development of computer aided analytical models. The geometrical characteristics of the sections may be computed using a bool algebra that operates with ‘simple’ geometrical shapes. By ‘simple’ we mean that for the according shapes we have direct calculus relations. In the set of ‘simple’ shapes we also have geometrical entities bounded by curves approximated as spline functions or as polygons. To conclude, computer programming offers the necessary support to solve general strength ship hull problems using analytical methods.

  9. Shipping

    OpenAIRE

    Wijnolst, N.; Wergeland, T.

    1996-01-01

    Shipping is a multi-faceted industry which is rather complex to define from an academic point of view. This book attempts to grasp these complexities and provide the reader with an overview of the main topics and terminology in shipping. The book is based on material from our courses in shipping at the universities in Delft and Bergen. As with our lectures, we draw upon quite a va ried material, from research studies at a high academic level to lower level student work and purely descriptive ...

  10. Uncertainty Quantification for a Sailing Yacht Hull, Using Multi-Fidelity Kriging

    NARCIS (Netherlands)

    de Baar, J.H.S.; Roberts, S; Dwight, R.P.; Mallol, B.

    2015-01-01

    Uncertainty Quantication (UQ) for CFD-based ship design can require a large number of simulations, resulting in signicant overall computational cost. Presently, we use an existing method, multi-delity Kriging, to reduce the number of simulations required for the UQ analysis of the performance of a

  11. Fast ship

    OpenAIRE

    Keuning, J.A.

    2014-01-01

    The invention concerns a ship whereby the hull and the mechanical propulsion device are designed such that the Froude number is larger than 0.5. In the aft ship the hull has a bottom with V-shaped bottom surfaces with a deadrise angle that is less than 40 degrees and the hull has substantially vertical sides. In the hull are a passenger compartment and a trim tank. The trim tank volume is such that the weight of a filled trim tank is more than 30 % of the weight of displacement of the hull wi...

  12. STUDI KOMPARASI KINERJA HULL FORM METODE SCHELTEMA DENGAN HULL FORM KAPAL IKAN TRADISIONAL TIPE DAERAH BATANG

    OpenAIRE

    A.F. Zakki; Parlindungan Manik

    2012-01-01

    This study comparation of hull form performance was analysed becaused there was suggestion that a ship was built by hull form scheming this time (Scheltema, Formdata, NPL Series) is better than a ship that was built traditionally because there is no basic erudite calculation in hull form design. So hull form design was result of natural adaptation. Such performance are ship’s resistance, stability, and ship’s navigation.This research about hull form performance is expected can giv...

  13. 46 CFR 115.802 - Hull.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull. 115.802 Section 115.802 Shipping COAST GUARD....802 Hull. (a) At each initial and subsequent inspection for certification of a vessel, the owner or managing operator shall be prepared to conduct tests and have the vessel ready for inspections of the hull...

  14. 46 CFR 176.802 - Hull.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull. 176.802 Section 176.802 Shipping COAST GUARD... CERTIFICATION Material Inspections § 176.802 Hull. (a) At each initial and subsequent inspection for... ready for inspections of the hull structure and its appurtenances, including the following: (1...

  15. 46 CFR 169.239 - Hull.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull. 169.239 Section 169.239 Shipping COAST GUARD... Certification Inspections § 169.239 Hull. At each inspection for certification and periodic inspection, the vessel must be afloat and ready for the following tests and inspections of the hull structure and its...

  16. Ship Vibrations

    DEFF Research Database (Denmark)

    Sørensen, Herman

    1997-01-01

    Methods for calculating natural frequencies for ship hulls and for plates and panels.Evaluation of the risk for inconvenient vibrations on board......Methods for calculating natural frequencies for ship hulls and for plates and panels.Evaluation of the risk for inconvenient vibrations on board...

  17. 46 CFR 151.10-20 - Hull construction.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Hull construction. 151.10-20 Section 151.10-20 Shipping... BULK LIQUID HAZARDOUS MATERIAL CARGOES Barge Hull Construction Requirements § 151.10-20 Hull construction. (a) Construction features. (1) Each barge hull shall be constructed with a suitable bow form...

  18. 46 CFR 154.174 - Transverse contiguous hull structure.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Transverse contiguous hull structure. 154.174 Section... Equipment Hull Structure § 154.174 Transverse contiguous hull structure. (a) The transverse contiguous hull...) The transverse contiguous hull structure of a vessel having cargo containment systems with secondary...

  19. 46 CFR 115.645 - Alternative Hull Examination (AHE) Procedure.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Alternative Hull Examination (AHE) Procedure. 115.645... AND CERTIFICATION Hull and Tailshaft Examinations § 115.645 Alternative Hull Examination (AHE... underwater hull plating and a detailed examination of all hull welds, propellers, tailshafts, rudders, and...

  20. Ship Detection Using Transfer Learned Single Shot Multi Box Detector

    Directory of Open Access Journals (Sweden)

    Nie Gu-Hong

    2017-01-01

    Full Text Available Ship detection in satellite images is a challenging task. In this paper, we introduce a transfer learned Single Shot MultiBox Detector (SSD for ship detection. To this end, a state-of-the-art object detection model pre-trained from a large number of natural images was transfer learned for ship detection with limited labeled satellite images. To the best of our knowledge, this could be one of the first studies which introduce SSD into ship detection on satellite images. Experiments demonstrated that our method could achieve 87.9% AP at 47 FPS using NVIDIA TITAN X. In comparison with Faster R-CNN, 6.7% AP improvement could be achieved. Effects of the observation resolution has also been studied with the changing input sizes among 300 × 300, 600 × 600 and 900 × 900. It has been noted that the detection accuracy declined sharply with the decreasing resolution that is mainly caused by the missing small ships.

  1. Measurements in a container ship of wave-induced hull girder stresses in excess of design values

    DEFF Research Database (Denmark)

    Andersen, Ingrid Marie Vincent; Jensen, Jørgen Juncher

    2014-01-01

    This paper describes full-scale measurements of the wave-induced vertical bending moment amidships a 9400 TEU container carrier and focuses on the effect of the hydro-elastic high-frequency vibration on the extreme hogging wave bending moment. One extreme event, where the vertical wave-induced ho...... is quite significant. Finally, the hydro-elastic behaviour of the hull girder is assessed by simple approximations using the measured statistical properties and closed-form expressions and the agreement with the actual measurements is found to be good. © 2014 Elsevier Ltd....

  2. Development of the hull inspection robot (RTV-SHIP); Sentai kensayo suichu robot (RTV-SHIP) no kaihatsu (atarashii sentai kensaho no ichiteian)

    Energy Technology Data Exchange (ETDEWEB)

    Nakata, Y.; Otsuka, M.; Ozawa, H.; Konosu, M. [Mitsui Engineering and Shipbuilding Co. Ltd., Tokyo (Japan)

    1997-08-01

    A compact and lightweight underwater RTV robot (RTV-SHIP) that enables the remote sensing in the double-shell structure of a tanker and the six-freedom motion control was developed based on the technology of the conventional portable underwater robot. The motion performance test in a water tank showed that the RTV-SHIP can freely access the manhole in the double-shell structure of a tanker and completely satisfies the thrust and swing force required for movement and measurement in a tank. The in-tank function confirmation test also shows that the main measurement items such as positioning in the tank, large deflection of panels, and plate thickness have a satisfactory measurement accuracy and that the RTV-SHIP has the same tone discrimination function as for a visual check. The method of inputting the tank shape during measurement and miniaturizing the recording unit should be improved until the RTV-SHIP is put to practical use. This system can be widely used by improving the above points according to the result of a future measurement test for the actual ships. 1 ref., 9 figs.

  3. 46 CFR 45.153 - Through-hull piping: General.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Through-hull piping: General. 45.153 Section 45.153... Conditions of Assignment § 45.153 Through-hull piping: General. (a) All through-hull pipes required by this subpart must be made of steel or material equivalent to the hull in strength and fatigue resistance. (b...

  4. 46 CFR 154.176 - Longitudinal contiguous hull structure.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Longitudinal contiguous hull structure. 154.176 Section... Equipment Hull Structure § 154.176 Longitudinal contiguous hull structure. (a) The longitudinal contiguous hull structure of a vessel having cargo containment systems without secondary barriers must meet the...

  5. 46 CFR 154.178 - Contiguous hull structure: Heating system.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Contiguous hull structure: Heating system. 154.178... Equipment Hull Structure § 154.178 Contiguous hull structure: Heating system. The heating system for transverse and longitudinal contiguous hull structure must: (a) Be shown by a heat load calculation to have...

  6. 46 CFR 154.180 - Contiguous hull structure: Welding procedure.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Contiguous hull structure: Welding procedure. 154.180... Equipment Hull Structure § 154.180 Contiguous hull structure: Welding procedure. Welding procedure tests for contiguous hull structure designed for a temperature colder than −18 °C (0 °F) must meet § 54.05-15 and...

  7. 46 CFR 151.10-1 - Barge hull classifications.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Barge hull classifications. 151.10-1 Section 151.10-1... CARRYING BULK LIQUID HAZARDOUS MATERIAL CARGOES Barge Hull Construction Requirements § 151.10-1 Barge hull classifications. (a) Each barge constructed or converted in conformance with this subpart shall be assigned a hull...

  8. 46 CFR 115.655 - Hull examination reports.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull examination reports. 115.655 Section 115.655... CERTIFICATION Hull and Tailshaft Examinations § 115.655 Hull examination reports. (a) If you use only divers for the underwater survey portion of the Alternative Hull Examination (AHE), you must provide the Officer...

  9. 46 CFR 154.188 - Membrane tank: Inner hull steel.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Membrane tank: Inner hull steel. 154.188 Section 154.188... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Hull Structure § 154.188 Membrane tank: Inner hull steel. For a vessel with membrane tanks, the inner hull...

  10. 46 CFR 176.655 - Hull examination reports.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull examination reports. 176.655 Section 176.655... TONS) INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 176.655 Hull examination reports. (a) If you use only divers for the underwater survey portion of the Alternative Hull Examination (AHE...

  11. 46 CFR 185.602 - Hull markings.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull markings. 185.602 Section 185.602 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) OPERATIONS Markings Required § 185.602 Hull markings. (a) Each vessel must be marked as required by part 67...

  12. 46 CFR 122.602 - Hull markings.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull markings. 122.602 Section 122.602 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150....602 Hull markings. (a) Each vessel must be marked as required by part 67, subpart I, of this chapter...

  13. 46 CFR 172.085 - Hull type.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull type. 172.085 Section 172.085 Shipping COAST GUARD... of This Chapter § 172.085 Hull type. If a cargo listed in Table 151.05 of part 151 of this chapter is to be carried, the tank barge must be at least the hull type specified in Table 151.05 of this...

  14. Presence of the tunicate Asterocarpa humilis on ship hulls and aquaculture facilities in the coast of the Biobío Region, south central Chile

    Directory of Open Access Journals (Sweden)

    Javier Pinochet

    2017-08-01

    Full Text Available Non-native ascidians are important members of the fouling community associated with artificial substrata and man-made structures. Being efficient fouling species, they are easily spread by human-mediated transports (e.g., with aquaculture trade and maritime transports. This is exemplified by the ascidian Asterocarpa humilis which displays a wide distribution in the Southern Hemisphere and has been recently reported in the Northern Hemisphere (NW Europe. In continental Chile, its first report dates back from 2000 for the locality of Antofagasta (23°S. Although there was no evidence about the vectors of introduction and spread, nor the source, some authors suggested maritime transport by ship hulls and aquaculture devices as putative introduction pathways and vectors. In the present study, we report for the first time the presence of A. humilis on the hull of an international ship in a commercial port in Concepción bay (36°S, south central Chile. We also found one individual associated to a seashell farm, 70 km far from Concepción bay. Further individuals were subsequently identified within Concepción bay: one juvenile settled upon international harbor pilings and a dozen individuals along aquaculture seashell longlines. For the first specimens sampled, species identification was ascertained using both morphological criteria and molecular barcoding, using the mitochondrial gene cytochrome c oxidase subunit I (COI and a nuclear gene (ribosomal RNA 18S. The nuclear 18S gene and the mitochondrial gene COI clearly assigned the specimens to A. humilis, confirming our morphological identification. Two haplotypes were obtained with COI corresponding to haplotypes previously obtained with European and Northern Chilean specimens. The present study thus reports for the first time the presence of A. humilis in the Araucanian ecoregion, documenting the apparent expansion of this non-native tunicate in Chile over 2,000 km, spanning over three ecoregions

  15. Anti-fouling protection on a ship's hull: evaluation of recent developments and formulation of innovative alternatives

    OpenAIRE

    Meskens, R.

    2017-01-01

    Marine fouling, or the growth of marine organisms on fully or partly submerged structures, is an unwanted phenomenon in the marine industry. Bio fouling will increase the hydrodynamic drag of ships, causing an increased fuel consumption, promote the corrosion of the metallic structures and trigger undesired transport of invasive species (IMO and the environment 2009, 2009).The impact is economic as well as environmental. More fuel consumption is synonym for more CO2 and other detrimental emis...

  16. 46 CFR 91.25-25 - Hull equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull equipment. 91.25-25 Section 91.25-25 Shipping COAST... CERTIFICATION Inspection for Certification § 91.25-25 Hull equipment. (a) At each inspection for certification and periodic inspection, the inspectors shall conduct the following tests and inspections of hull...

  17. 46 CFR 45.107 - Strength of hull.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Strength of hull. 45.107 Section 45.107 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES GREAT LAKES LOAD LINES Conditions of Assignment § 45.107 Strength of hull. The general structural strength of the hull must be sufficient for the...

  18. 46 CFR 154.516 - Piping: Hull protection.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Piping: Hull protection. 154.516 Section 154.516 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY... and Process Piping Systems § 154.516 Piping: Hull protection. A vessel's hull must be protected from...

  19. 46 CFR 111.05-11 - Hull return.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull return. 111.05-11 Section 111.05-11 Shipping COAST... REQUIREMENTS Equipment Ground, Ground Detection, and Grounded Systems § 111.05-11 Hull return. (a) A vessel's hull must not carry current as a conductor except for the following systems: (1) Impressed current...

  20. 46 CFR 189.25-25 - Hull equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull equipment. 189.25-25 Section 189.25-25 Shipping... CERTIFICATION Inspection for Certification § 189.25-25 Hull equipment. (a) At each inspection for certification and periodic inspection the inspector shall conduct the following tests and inspections of hull...

  1. 46 CFR 71.25-25 - Hull equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Hull equipment. 71.25-25 Section 71.25-25 Shipping COAST... Inspection § 71.25-25 Hull equipment. (a) At each annual inspection, the inspector shall conduct the following tests and inspections of hull equipment: (1) All subdivision bulkheads shall be examined to...

  2. 46 CFR 308.107 - War risk hull insurance policy.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 8 2010-10-01 2010-10-01 false War risk hull insurance policy. 308.107 Section 308.107 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War Risk Hull and Disbursements Insurance § 308.107 War risk hull insurance policy. Standard Form MA-240...

  3. 46 CFR 32.75-5 - Hull requirements; general-TB/ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Hull requirements; general-TB/ALL. 32.75-5 Section 32.75..., AND HULL REQUIREMENTS Hull Requirements for Wood Hull Tank Vessels Constructed Prior to November 10, 1936 § 32.75-5 Hull requirements; general—TB/ALL. The scantlings, material, and workmanship, and the...

  4. 46 CFR 32.70-5 - Hull requirements; general-TB/ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Hull requirements; general-TB/ALL. 32.70-5 Section 32.70..., AND HULL REQUIREMENTS Hull Requirements for Steel Hull Tank Vessels Constructed Prior to November 10, 1936 § 32.70-5 Hull requirements; general—TB/ALL. The scantlings, material, and workmanship, the...

  5. Ship Domain Model for Multi-ship Collision Avoidance Decision-making with COLREGs Based on Artificial Potential Field

    Directory of Open Access Journals (Sweden)

    TengFei Wang

    2017-03-01

    Full Text Available A multi-ship collision avoidance decision-making and path planning formulation is studied in a distributed way. This paper proposes a complete set of solutions for multi-ship collision avoidance in intelligent navigation, by using a top-to-bottom organization to structure the system. The system is designed with two layers: the collision avoidance decision-making and the path planning. Under the general requirements of the International Regulations for Preventing Collisions at Sea (COLREGs, the performance of distributed path planning decision-making for anti-collision is analyzed for both give-way and stand-on ships situations, including the emergency actions taken by the stand-on ship in case of the give-way ship’s fault of collision avoidance measures. The Artificial Potential Field method(APF is used for the path planning in details. The developed APF method combined with the model of ship domain takes the target ships’ speed and course in-to account, so that it can judge the moving characteristics of obstacles more accurately. Simulation results indicate that the system proposed can work effectiveness.

  6. Multi-agent adaptive systems in dry bulk shipping

    NARCIS (Netherlands)

    Engelen, Steve; Dullaert, Wout; Vernimmen, Bert

    Investment decisions in dry bulk shipping form one of the most difficult managerial tasks due to the high degree of uncertainty and the cyclical nature of the market. Adequate information on ship prices is, therefore, crucial when justifying such decisions. This paper is the first to embed trading

  7. 46 CFR 169.231 - Definitions relating to hull examinations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Definitions relating to hull examinations. 169.231... hull examinations. As used in the part— (a) Drydock examination means hauling out a vessel or placing a... and all through-hull fittings, sea chests, sea valves, sea strainers, and valves for the emergency...

  8. 46 CFR 154.170 - Outer hull steel plating.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Outer hull steel plating. 154.170 Section 154.170... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Hull Structure § 154.170 Outer hull steel plating. (a) Except as required in paragraph (b) of this section, the...

  9. 46 CFR 71.50-29 - Hull examination reports.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Hull examination reports. 71.50-29 Section 71.50-29... CERTIFICATION Drydocking § 71.50-29 Hull examination reports. (a) If you use only divers for the underwater survey portion of the Alternative Hull Examination (AHE), you must provide the Officer in Charge, Marine...

  10. 46 CFR 154.172 - Contiguous steel hull structure.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Contiguous steel hull structure. 154.172 Section 154.172... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Hull Structure § 154.172 Contiguous steel hull structure. (a) Except as allowed in paragraphs (b) and (c) of this...

  11. 46 CFR 252.33 - Hull and machinery insurance.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 8 2010-10-01 2010-10-01 false Hull and machinery insurance. 252.33 Section 252.33... Subsidy Rates § 252.33 Hull and machinery insurance. (a) Subsidy items. The fair and reasonable net premium costs (including stamp taxes) of hull and machinery, increased value, excess general average...

  12. 46 CFR 282.23 - Hull and machinery insurance.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 8 2010-10-01 2010-10-01 false Hull and machinery insurance. 282.23 Section 282.23... COMMERCE OF THE UNITED STATES Calculation of Subsidy Rates § 282.23 Hull and machinery insurance. (a) Subsidy items. The fair and reasonable net premium costs (including stamp taxes) of hull and machinery...

  13. Inspecting the inside of underwater hull

    Science.gov (United States)

    Valkovic, Vladivoj; Sudac, Davorin

    2009-05-01

    In order to demonstrate the possibility of identifying the material within ship's underwater hull, sunken ships and other objects on the sea floor tests with the 14 MeV sealed tube neutron generator incorporated inside a small submarine submerged in the test basin filled with sea water have been performed. Results obtained for inspection of diesel fuel and explosive presence behind single and double hull constructions are presented.

  14. 46 CFR 91.15-1 - Standards in inspection of hulls, boilers, and machinery.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Standards in inspection of hulls, boilers, and machinery... hulls, boilers, and machinery. In the inspection of hulls, boilers, and machinery of vessels, the..., respecting material and inspection of hulls, boilers, and machinery, and the certificate of classification...

  15. 46 CFR 189.15-1 - Standards in inspection of hulls, boilers, and machinery.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Standards in inspection of hulls, boilers, and machinery... inspection of hulls, boilers, and machinery. In the inspection of hulls, boilers, and machinery of vessels... chapter, respecting material and construction of hulls, boilers, and machinery, and certificate of...

  16. 46 CFR 32.63-5 - Barge hull classifications-B/ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Barge hull classifications-B/ALL. 32.63-5 Section 32.63..., AND HULL REQUIREMENTS Hull and Cargo Tank Requirements for Tank Barges Constructed or Converted On or After July 1, 1964, and Carrying Certain Dangerous Bulk Cargoes § 32.63-5 Barge hull classifications—B...

  17. 46 CFR 71.50-1 - Definitions relating to hull examinations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Definitions relating to hull examinations. 71.50-1... INSPECTION AND CERTIFICATION Drydocking § 71.50-1 Definitions relating to hull examinations. As used in this part— Adequate hull protection system means a method of protecting the vessel's hull from corrosion. It...

  18. 46 CFR 115.630 - The Alternative Hull Examination (AHE) Program application.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false The Alternative Hull Examination (AHE) Program... PASSENGERS INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 115.630 The Alternative Hull... hull examination date to the Officer in Charge, Marine Inspection (OCMI) who will oversee the survey...

  19. CFD simulation on Kappel propeller with a hull wake field

    DEFF Research Database (Denmark)

    Shin, Keun Woo; Andersen, Poul; Møller Bering, Rasmus

    2013-01-01

    Marine propellers are designed not for the open-water operation, but for the operation behind a hull due to the inhomogeneous hull wake and thrust deduction. The adaptation for the hull wake is important for the propulsive efficiency and cavitation risk especially on single-screw ships. CFD...... simulations for a propeller with a hull model have showed acceptable agreement with a model test result in the thrust and torque (Larsson et al. 2010). In the current work, a measured hull wake is applied to the simulation instead of modelling a hull, because the hull geometry is mostly not available...... for propeller designers and the computational effort can be reduced by excluding the hull. The CFD simulation of a propeller flow with a hull wake is verified in order to use CFD as a propeller design tool. A Kappel propeller, which is an innovative tip-modified propeller, is handled. Kappel propellers...

  20. 46 CFR 45.143 - Hull openings above freeboard deck.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Hull openings above freeboard deck. 45.143 Section 45.143 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES GREAT LAKES LOAD LINES Conditions of Assignment § 45.143 Hull openings above freeboard deck. Closures for openings above...

  1. 46 CFR 78.50-5 - Hull markings.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Hull markings. 78.50-5 Section 78.50-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS OPERATIONS Markings on Vessels § 78.50-5 Hull markings. Vessels shall be marked as required by parts 67 and 69 of this chapter. [CGD 72...

  2. 46 CFR 196.40-5 - Hull markings.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull markings. 196.40-5 Section 196.40-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS OPERATIONS Markings on Vessels § 196.40-5 Hull markings. Vessels shall be marked as required by parts 67 and 69 of this chapter...

  3. 46 CFR 97.40-5 - Hull markings.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull markings. 97.40-5 Section 97.40-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CARGO AND MISCELLANEOUS VESSELS OPERATIONS Markings on Vessels § 97.40-5 Hull markings. Vessels shall be marked as required by parts 67 and 69 of this...

  4. 46 CFR 174.225 - Hull penetrations and shell connections.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Hull penetrations and shell connections. 174.225 Section 174.225 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SUBDIVISION AND STABILITY... § 174.225 Hull penetrations and shell connections. Each overboard discharge and shell connection except...

  5. Ship Detection and Measurement of Ship Motion by Multi-Aperture Synthetic Aperture Radar

    Science.gov (United States)

    2014-06-01

    otherwise they would break. Both transverse and torsional modes are present and are driven by the ship structure, the shape of the sea surface, bow slamming...used, the ship’s loading and the ship’s operation [11], [16]. Very large vessels are the most flexible . The schematic shown in Figure 4 [12] provides...different orientations and thin (with respect to a radar wavelength) rods and cables act as linear diffraction centers. The orientation of the

  6. 46 CFR 32.63-20 - Hull structure-B/ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Hull structure-B/ALL. 32.63-20 Section 32.63-20 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS SPECIAL EQUIPMENT, MACHINERY, AND HULL REQUIREMENTS Hull and Cargo Tank Requirements for Tank Barges Constructed or Converted On or After July 1, 1964...

  7. 46 CFR 45.135 - Hull openings at or below freeboard deck.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Hull openings at or below freeboard deck. 45.135 Section 45.135 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES GREAT LAKES LOAD LINES Conditions of Assignment § 45.135 Hull openings at or below freeboard deck. Closures for hull...

  8. 46 CFR 108.133 - Hull superstructure, structural bulkheads, decks, and deckhouses.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Hull superstructure, structural bulkheads, decks, and deckhouses. 108.133 Section 108.133 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A... Protection § 108.133 Hull superstructure, structural bulkheads, decks, and deckhouses. Each hull...

  9. 46 CFR 167.15-27 - Definitions relating to hull examinations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Definitions relating to hull examinations. 167.15-27... PUBLIC NAUTICAL SCHOOL SHIPS Inspections § 167.15-27 Definitions relating to hull examinations. As used... slipway for an examination of all accessible parts of the vessel's underwater body and all through-hull...

  10. Alpha-Concave Hull, a Generalization of Convex Hull

    OpenAIRE

    Asaeedi, Saeed; Didehvar, Farzad; Mohades, Ali

    2013-01-01

    Bounding hull, such as convex hull, concave hull, alpha shapes etc. has vast applications in different areas especially in computational geometry. Alpha shape and concave hull are generalizations of convex hull. Unlike the convex hull, they construct non-convex enclosure on a set of points. In this paper, we introduce another generalization of convex hull, named alpha-concave hull, and compare this concept with convex hull and alpha shape. We show that the alpha-concave hull is also a general...

  11. Study on practical application of a longitudinal hull strength theory considering camber in cross section; Yokodanmen no sori wo koryoshita sentai tate kyodo riron no jitsuyoka ni kansuru kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    Nose, M; Suzuki, K; Furuno, H [Nagasaki Institute of Applied Science, Nagasaki (Japan); Suzuki, K

    1997-10-01

    Discussions were given on practical application of a stress analyzing method for thin-wall deformed cross-sectional beam considering cross section camber in longitudinal bending. The non-static calculation method described in the previous report can be applied to a box-type cross section having multi-connected cells, bulk cargo transport vessels and container ships with dual hull structure, and oil tankers with dual hull structure of medium size. The calculation method was capable of achieving remarkable enhancement in efficiency over that of conventional calculation methods. The present study is intended to make the method applicable also to multi-connected cross section shapes having more than one longitudinal partitions as used in dual hull VLCC and ULCC. As a result, an expanded non-static calculation system was developed, which has introduced into the conception described in the previous report a new conception of triple point and independent start point members. As a result of applying the method to dual hull bulk cargo transport vessels, container ships, dual hull oil tankers of medium size, VLCC and ULCC, it was verified that the system operated properly. Remarkable efficiency improvement has been made possible as compared with conventional analysis methods applied to individual ships. The system is capable of automatic calculation, and makes possible the practical application of the hull strength theory considering cross section camber. 3 refs., 10 figs., 1 tab.

  12. 46 CFR 167.15-25 - Inspection standards for hulls, boilers and machinery.

    Science.gov (United States)

    2010-10-01

    ... SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Inspections § 167.15-25 Inspection standards for hulls, boilers and... 46 Shipping 7 2010-10-01 2010-10-01 false Inspection standards for hulls, boilers and machinery... inspection. These rules may be purchased from the American Bureau of Shipping (ABS), ABS Plaza, 16855...

  13. Optimizing Ship Classification in the Arctic Ocean: A Case Study of Multi-Disciplinary Problem Solving

    Directory of Open Access Journals (Sweden)

    Mark Rahmes

    2014-08-01

    Full Text Available We describe a multi-disciplinary system model for determining decision making strategies based upon the ability to perform data mining and pattern discovery utilizing open source actionable information to prepare for specific events or situations from multiple information sources. We focus on combining detection theory with game theory for classifying ships in Arctic Ocean to verify ship reporting. More specifically, detection theory is used to determine probability of deciding if a ship or certain ship class is present or not. We use game theory to fuse information for optimal decision making on ship classification. Hierarchy game theory framework enables complex modeling of data in probabilistic modeling. However, applicability to big data is complicated by the difficulties of inference in complex probabilistic models, and by computational constraints. We provide a framework for fusing sensor inputs to help compare if the information of a ship matches its AIS reporting requirements using mixed probabilities from game theory. Our method can be further applied to optimizing other choke point scenarios where a decision is needed for classification of ground assets or signals. We model impact on decision making on accuracy by adding more parameters or sensors to the decision making process as sensitivity analysis.

  14. 46 CFR 176.620 - Description of the Alternative Hull Examination (AHE) Program for certain passenger vessels.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Description of the Alternative Hull Examination (AHE... Hull and Tailshaft Examinations § 176.620 Description of the Alternative Hull Examination (AHE) Program for certain passenger vessels. The Alternative Hull Examination (AHE) Program provides you with an...

  15. 46 CFR 176.625 - Eligibility requirements for the Alternative Hull Examination (AHE) Program for certain passenger...

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Eligibility requirements for the Alternative Hull... CERTIFICATION Hull and Tailshaft Examinations § 176.625 Eligibility requirements for the Alternative Hull... if— (1) It is constructed of steel or aluminum; (2) It has an effective hull protection system; (3...

  16. Wave induced extreme hull girder loads on containerships

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher; Pedersen, Preben Terndrup; Shi, Bill

    2009-01-01

    This paper provides simple but rational procedures for prediction of extreme wave – induced sectional hull girder forces with reasonable engineering accuracy. The procedures take into account main ship hull characteristics such as: length, breadth, draught, block coefficient, bow flare coefficient......, forward speed and hull flexibility. The vertical hull girder loads are evaluated for specific operational profiles. Firstly a quadratic strip theory is presented which can give separate predictions for the hogging and sagging bending moments and shear forces and for hull girder loads. Then this procedure...... is based on rational methods it can be applied for novel single hull ship types not presently covered by the rules of the classification societies or to account for specific operational profiles....

  17. Nuclear ships and their safety

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1961-04-15

    Several aspects of nuclear ship propulsion, with special reference to nuclear safety, were discussed at an international symposium at Taormina, Italy, from 14-18 November 1960. Discussions on specific topics are conducted, grouped under the following headings: Economics and National Activities in Nuclear Ship Propulsion; International Problems and General Aspects of Safety for Nuclear Ships; Nuclear Ship Projects from the Angle of Safety; Ship Reactor Problems; Sea Motion and Hull Problems; Maintenance and Refuelling Problems; and Safety Aspects of Nuclear Ship Operation.

  18. Fluid-Structure Interaction Effects Resulting from Hull Appendage Coupling

    National Research Council Canada - National Science Library

    Avcu, Mehmet

    2005-01-01

    In previous work conducted in the modeling and simulation of ships subjected to underwater explosions, there has been some debate over the influence that hull appendages have upon the dynamic response...

  19. Estimating Hull Coating Thickness Distributions Using the EM Algorithm

    National Research Council Canada - National Science Library

    Corriere, Michael

    2000-01-01

    The underwater hull coating system on surface ships is comprised anti-corrosive (AC) and anti-fouling (AF) paint The AF layers are designed to wear away, continuously leaching cuprous oxide to inhibit marine growth...

  20. Calculation for Hull Strength Construction in Offshore Structures

    African Journals Online (AJOL)

    PROF. O. E. OSUAGWU

    2013-09-01

    Sep 1, 2013 ... of hull plating, reinforcing stiffeners, girders, and other structures. This paper therefore used the .... From these equations we derive that. Safety of. Factor. Stress ..... machineries, systems etc. of the ships or barge under design.

  1. 46 CFR 71.15-1 - Standards in inspection of hulls, boilers, and machinery.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Standards in inspection of hulls, boilers, and machinery..., boilers, and machinery. In the inspection of hulls, boilers, and machinery of vessels, the standards... and inspection of hulls, boilers, and machinery, and the certificate of classification referring...

  2. 46 CFR 115.660 - Continued participation in the Alternative Hull Examination (AHE) Program.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Continued participation in the Alternative Hull... MORE THAN 49 PASSENGERS INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 115.660 Continued participation in the Alternative Hull Examination (AHE) Program. (a) To continue to participate in...

  3. 46 CFR 71.50-31 - Continued participation in the Alternative Hull Examination (AHE) program.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Continued participation in the Alternative Hull... the Alternative Hull Examination (AHE) program. (a) To continue to participate in the AHE Program, vessel operators must conduct an annual hull condition assessment. At a minimum, vessel operators must...

  4. 46 CFR 176.660 - Continued participation in the Alternative Hull Examination (AHE) Program.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Continued participation in the Alternative Hull... (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 176.660 Continued participation in the Alternative Hull Examination (AHE) Program. (a) To...

  5. 46 CFR 42.09-30 - Additional survey requirements for steel-hull vessels.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Additional survey requirements for steel-hull vessels...-30 Additional survey requirements for steel-hull vessels. (a) In addition to the requirements in § 42...) When the vessel is in drydock, the hull plating, etc., shall be examined. (c) The holds, 'tween decks...

  6. 46 CFR 31.10-20 - Definitions relating to hull examinations-T/B ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Definitions relating to hull examinations-T/B ALL. 31.10... CERTIFICATION Inspections § 31.10-20 Definitions relating to hull examinations—T/B ALL. As used in this part— (a... examination of all accessible parts of the vessel's underwater body and all through-hull fittings. (b...

  7. 46 CFR 176.630 - The Alternative Hull Examination (AHE) Program application.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false The Alternative Hull Examination (AHE) Program... PASSENGER VESSELS (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 176.630 The Alternative Hull Examination (AHE) Program application. If your vessel meets the eligibility...

  8. 46 CFR 91.40-1 - Definitions relating to hull examinations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Definitions relating to hull examinations. 91.40-1... VESSELS INSPECTION AND CERTIFICATION Drydocking § 91.40-1 Definitions relating to hull examinations. As...-hull fittings. (b) Internal structural examination means an examination of the vessel while afloat or...

  9. 46 CFR 71.50-25 - Alternative Hull Examination (AHE) procedure.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Alternative Hull Examination (AHE) procedure. 71.50-25... INSPECTION AND CERTIFICATION Drydocking § 71.50-25 Alternative Hull Examination (AHE) procedure. (a) To complete the underwater survey you must— (1) Perform a general examination of the underwater hull plating...

  10. 46 CFR 176.650 - Alternative Hull Examination Program options: Divers or underwater ROV.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Alternative Hull Examination Program options: Divers or...) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 176.650 Alternative Hull Examination Program options: Divers or underwater ROV. To complete the...

  11. 46 CFR 71.50-19 - The Alternative Hull Examination (AHE) Program application.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false The Alternative Hull Examination (AHE) Program...) PASSENGER VESSELS INSPECTION AND CERTIFICATION Drydocking § 71.50-19 The Alternative Hull Examination (AHE... apply to the AHE Program. You must submit an application at least 90 days before the requested hull...

  12. 46 CFR 189.40-1 - Definitions relating to hull examinations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Definitions relating to hull examinations. 189.40-1... VESSELS INSPECTION AND CERTIFICATION Drydocking § 189.40-1 Definitions relating to hull examinations. As...-hull fittings. (b) Internal structural examination means an examination of the vessel while afloat or...

  13. 46 CFR 115.650 - Alternative Hull Examination (AHE) Program options: Divers or underwater ROV.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Alternative Hull Examination (AHE) Program options... MORE THAN 49 PASSENGERS INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 115.650 Alternative Hull Examination (AHE) Program options: Divers or underwater ROV. To complete your underwater...

  14. Nuclear ship engineering simulator

    International Nuclear Information System (INIS)

    Itoh, Yasuyoshi; Kusunoki, Tsuyoshi; Hashidate, Koji

    1991-01-01

    The nuclear ship engineering simulator, which analyzes overall system response of nuclear ship numerically, is now being developed by JAERI as an advanced design tool with the latest computer technology in software and hardware. The development of the nuclear ship engineering simulator aims at grasping characteristics of a reactor plant under the situation generated by the combination of ocean, a ship hull and a reactor. The data from various tests with the nuclear ship 'MUTSU' will be used for this simulator to modulate and verify its functions of reproducing realistic response of nuclear ship, and then the simulator will be utilized for the research and development of advanced marine reactors. (author)

  15. Hydrodynamics of Ship Propellers

    DEFF Research Database (Denmark)

    Breslin, John P.; Andersen, Poul

    This book deals with flows over propellers operating behind ships, and the hydrodynamic forces and moments which the propeller generates on the shaft and on the ship hull.The first part of the text is devoted to fundamentals of the flow about hydrofoil sections (with and without cavitation...... of an intermittently cavitating propeller in a wake and the pressures and forces it exerts on the shaft and on the ship hull is examined. A final chapter discusses the optimization of efficiency of compound propulsors. The authors have taken care to clearly describe physical concepts and mathematical steps. Appendices...

  16. Committee VI.1. Extreme Hull Girder Loading

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher

    2000-01-01

    Committee Mandate. Evaluate and develop direct calculation procedures for extreme wawe loads on ship hull girders. Due consideration shall be given to stochastic and non-linear effects. The procedures shall be assessed by comparison with in-service experiences, model tests and more refined...

  17. 46 CFR 154.182 - Contiguous hull structure: Production weld test.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Contiguous hull structure: Production weld test. 154.182... Equipment Hull Structure § 154.182 Contiguous hull structure: Production weld test. If a portion of the contiguous hull structure is designed for a temperature colder than −34 °C (−30 °F) and is not part of the...

  18. In-Water Hull Cleaning & Filtration System

    Science.gov (United States)

    George, Dan

    2015-04-01

    Dan George R & D Mining Technology LinkedIn GRD Franmarine have received the following prestigious awards in 2014 for their research & development of an in-water hull cleaning and filtration system "The Envirocart: Golden Gecko Award for Environmental Excellence; WA Innovator of the Year - Growth Sector; Department of Fisheries - Excellence in Marine Biosecurity Award - Innovation Category; Lloyd's List Asia Awards - Environmental Award; The Australian Innovation Challenge - Environment, Agriculture and Food Category; and Australian Shipping and Maritime Industry Award - Environmental Transport Award. The Envirocart developed and patented by GRD Franmarine is a revolutionary new fully enclosed capture and containment in-water hull cleaning technology. The Envirocart enables soft Silicon based antifouling paints and coatings containing pesticides such as Copper Oxide to be cleaned in situ using a contactless cleaning method. This fully containerised system is now capable of being deployed to remote locations or directly onto a Dive Support Vessel and is rated to offshore specifications. This is the only known method of in-water hull cleaning that complies with the Department of Agriculture Fisheries and Forestry (DAFF) and Department of Fisheries WA (DoF) Guidelines. The primary underwater cleaning tool is a hydraulically powered hull cleaning unit fitted with rotating discs. The discs can be fitted with conventional brushes for glass or epoxy based coatings or a revolutionary new patented blade system which can remove marine biofouling without damaging the antifouling paint (silicone and copper oxide). Additionally there are a patented range of fully enclosed hand cleaning tools for difficult to access niche areas such as anodes and sea chests, providing an innovative total solution that enables in-water cleaning to be conducted in a manner that causes no biological risk to the environment. In full containment mode or when AIS are present, material is pumped

  19. Morphologically intelligent underactuated robot for underwater hull cleaning

    DEFF Research Database (Denmark)

    Souto, Daniel; Faina, Andres; López-Peña, Fernando

    2015-01-01

    In this paper we discuss a new type of robot for underwater hull cleaning on ships with non-magnetic hulls. This robot is based on the concept that cleaning hulls regularly, without waiting to take them out of the water, will improve the efficiency of the ships and will permit a reduction...... in the use of the chemicals that are usually employed to prevent the growth of marine life on the hull and which are generally harmful to the environment. The robot described in this paper is an underactuated morphologically adapted robot that through an appropriate morphology and making use of the forces...... and constraints of the environment solves the most difficult problems that arise when moving along hulls. Some of these are changing planes, negotiating appendices, avoiding portholes, passing corners, and other elements. This greatly simplifies the control mechanisms that are required for its operation making...

  20. 46 CFR 42.09-35 - Additional survey requirements for wood-hull vessels.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Additional survey requirements for wood-hull vessels. 42.09-35 Section 42.09-35 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES... Additional survey requirements for wood-hull vessels. (a) In addition to the requirements in § 42.09-25, the...

  1. Hull-Propeller Interaction and Its Effect on Propeller Cavitation

    DEFF Research Database (Denmark)

    Regener, Pelle Bo

    In order to predict the required propulsion power for a ship reliably and accurately, it is not sufficient to only evaluate the resistance of the hull and the propeller performance in open water alone. Interaction effects between hull and propeller can even be a decisive factor in ship powering...... prediction and design optimization. The hull-propeller interaction coefficients of effective wake fraction, thrust deduction factor, and relative rotative efficiency are traditionally determined by model tests. Self-propulsion model tests consistently show an increase in effective wake fractions when using...... velocities. This offers an opportunity for additional insight into hull-propeller interaction and the propeller’s actual operating condition behind the ship, as the actual (effective) inflow is computed. Self-propulsion simulations at model and full scale were carried out for a bulk carrier, once...

  2. RANS simulation of cavitation and hull pressure fluctuation for marine propeller operating behind-hull condition

    Science.gov (United States)

    Paik, Kwang-Jun; Park, Hyung-Gil; Seo, Jongsoo

    2013-12-01

    Simulations of cavitation flow and hull pressure fluctuation for a marine propeller operating behind a hull using the unsteady Reynolds-Averaged Navier-Stokes equations (RANS) are presented. A full hull body submerged under the free surface is modeled in the computational domain to simulate directly the wake field of the ship at the propeller plane. Simulations are performed in design and ballast draught conditions to study the effect of cavitation number. And two propellers with slightly different geometry are simulated to validate the detectability of the numerical simulation. All simulations are performed using a commercial CFD software FLUENT. Cavitation patterns of the simulations show good agreement with the experimental results carried out in Samsung CAvitation Tunnel (SCAT). The simulation results for the hull pressure fluctuation induced by a propeller are also compared with the experimental results showing good agreement in the tendency and amplitude, especially, for the first blade frequency.

  3. RANS simulation of cavitation and hull pressure fluctuation for marine propeller operating behind-hull condition

    Directory of Open Access Journals (Sweden)

    Kwang-Jun Paik

    2013-12-01

    Full Text Available Simulations of cavitation flow and hull pressure fluctuation for a marine propeller operating behind a hull using the unsteady Reynolds-Averaged Navier-Stokes equations (RANS are presented. A full hull body submerged under the free surface is modeled in the computational domain to simulate directly the wake field of the ship at the propeller plane. Simulations are performed in design and ballast draught conditions to study the effect of cavitation number. And two propellers with slightly different geometry are simulated to validate the detectability of the numerical simulation. All simulations are performed using a commercial CFD software FLUENT. Cavitation patterns of the simulations show good agreement with the experimental results carried out in Samsung CAvitation Tunnel (SCAT. The simulation results for the hull pressure fluctuation induced by a propeller are also compared with the experimental results showing good agreement in the tendency and amplitude, especially, for the first blade frequency.

  4. Panel cutting method: new approach to generate panels on a hull in Rankine source potential approximation

    Directory of Open Access Journals (Sweden)

    Hee-Jong Choi

    2011-12-01

    Full Text Available In the present study, a new hull panel generation algorithm, namely panel cutting method, was developed to predict flow phenomena around a ship using the Rankine source potential based panel method, where the iterative method was used to satisfy the nonlinear free surface condition and the trim and sinkage of the ship was taken into account. Numerical computations were performed to investigate the validity of the proposed hull panel generation algorithm for Series 60 (CB=0.60 hull and KRISO container ship (KCS, a container ship designed by Maritime and Ocean Engineering Research Institute (MOERI. The computational results were validated by comparing with the existing experimental data.

  5. Panel cutting method: new approach to generate panels on a hull in Rankine source potential approximation

    Science.gov (United States)

    Choi, Hee-Jong; Chun, Ho-Hwan; Park, Il-Ryong; Kim, Jin

    2011-12-01

    In the present study, a new hull panel generation algorithm, namely panel cutting method, was developed to predict flow phenomena around a ship using the Rankine source potential based panel method, where the iterative method was used to satisfy the nonlinear free surface condition and the trim and sinkage of the ship was taken into account. Numerical computations were performed to investigate the validity of the proposed hull panel generation algorithm for Series 60 (CB=0.60) hull and KRISO container ship (KCS), a container ship designed by Maritime and Ocean Engineering Research Institute (MOERI). The computational results were validated by comparing with the existing experimental data.

  6. 46 CFR 71.50-27 - Alternative Hull Examination (AHE) program options: Divers or underwater remotely operated...

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Alternative Hull Examination (AHE) program options...-27 Alternative Hull Examination (AHE) program options: Divers or underwater remotely operated vehicle... operations; (2) Provide permanent hull markings, a temporary grid system of wires or cables spaced not more...

  7. 46 CFR 115.620 - Description of the Alternative Hull Examination (AHE) Program for certain passenger vessels.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Description of the Alternative Hull Examination (AHE... ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 115.620 Description of the Alternative Hull Examination (AHE) Program for certain passenger vessels. The Alternative...

  8. 46 CFR 71.50-15 - Description of the Alternative Hull Examination (AHE) Program for certain passenger vessels.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Description of the Alternative Hull Examination (AHE... Description of the Alternative Hull Examination (AHE) Program for certain passenger vessels. The Alternative Hull Examination (AHE) Program provides you with an alternative to a drydock examination by allowing...

  9. 46 CFR 71.50-3 - Drydock examination, internal structural examination, underwater survey, and alternate hull exam...

    Science.gov (United States)

    2010-10-01

    ..., underwater survey, and alternate hull exam intervals. 71.50-3 Section 71.50-3 Shipping COAST GUARD...-3 Drydock examination, internal structural examination, underwater survey, and alternate hull exam... wooden hulls must undergo two drydock and two internal structural examinations within any five year...

  10. 46 CFR 115.625 - Eligibility requirements for the Alternative Hull Examination (AHE) Program for certain passenger...

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Eligibility requirements for the Alternative Hull... OVERNIGHT ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS INSPECTION AND CERTIFICATION Hull and Tailshaft Examinations § 115.625 Eligibility requirements for the Alternative Hull Examination (AHE) Program for certain...

  11. 46 CFR 71.50-17 - Eligibility requirements for the Alternative Hull Examination (AHE) Program for certain passenger...

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Eligibility requirements for the Alternative Hull...-17 Eligibility requirements for the Alternative Hull Examination (AHE) Program for certain passenger... aluminum; (2) It has an effective hull protection system; (3) It has operated exclusively in fresh water...

  12. On Grounding of Fast Ships

    DEFF Research Database (Denmark)

    Simonsen, Bo Cerup; Pedersen, Preben Terndrup

    1997-01-01

    The paper deals with analysis of grounding of high-speed crafts. It is the purpose to present a comprehensive mathematical model for calculation of the overall dynamic ship response during grounding. This procedure is applied to derive the motions, the time varying sectional forces and the local...... loads during grounding on plane, sloping, sandy bottoms for six different designs of fast monohull ships made from steel, aluminium or GRP sandwich materials. The results show that the effect of the hull flexibility is to reduce the overall dynamic sectional loads on the hull girder. The considered...... numerical examples also indicate that, even with impact speeds of 40 knots against a 1:10 sloping bottom, the global strength of the hull girder is not exceeded by the grounding induced loads.For the local deformation of high-speed ship hulls at the point of contact with the ground, the paper presents...

  13. Structural health monitoring for ship structures

    Energy Technology Data Exchange (ETDEWEB)

    Farrar, Charles [Los Alamos National Laboratory; Park, Gyuhae [Los Alamos National Laboratory; Angel, Marian [Los Alamos National Laboratory; Bement, Matthew [Los Alamos National Laboratory; Salvino, Liming [NSWC, CADEROCK

    2009-01-01

    Currently the Office of Naval Research is supporting the development of structural health monitoring (SHM) technology for U.S. Navy ship structures. This application is particularly challenging because of the physical size of these structures, the widely varying and often extreme operational and environmental conditions associated with these ships missions, lack of data from known damage conditions, limited sensing that was not designed specifically for SHM, and the management of the vast amounts of data that can be collected during a mission. This paper will first define a statistical pattern recognition paradigm for SHM by describing the four steps of (1) Operational Evaluation, (2) Data Acquisition, (3) Feature Extraction, and (4) Statistical Classification of Features as they apply to ship structures. Note that inherent in the last three steps of this process are additional tasks of data cleansing, compression, normalization and fusion. The presentation will discuss ship structure SHM challenges in the context of applying various SHM approaches to sea trials data measured on an aluminum multi-hull high-speed ship, the HSV-2 Swift. To conclude, the paper will discuss several outstanding issues that need to be addressed before SHM can make the transition from a research topic to actual field applications on ship structures and suggest approaches for addressing these issues.

  14. Latest Trends in the Monitoring of Ships’s Hull Underwater Part and Analysis of Its Effectiveness

    OpenAIRE

    Urbahs, A; Carjova, K; Vulans, P; Straume, R

    2012-01-01

    Ship operation is not possible without regular maintenance, inspection and certification, established by international and domestic law, where one of the main goals is an effective operation of a ship. To achieve this, it is important to reduce time and costs involved in carrying out the surveys. This paper explores the law under which it’s required for ship to have inspection of underwater part; identifies problems of ship’s hull underwater part; analyze latest trends in ship's hull underwat...

  15. Mechanics of Ship Grounding

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup

    1996-01-01

    In these notes first a simplified mathematical model is presented for analysis of ship hull loading due to grounding on relatively hard and plane sand, clay or rock sea bottoms. In a second section a more rational calculation model is described for the sea bed soil reaction forces on the sea bott...

  16. Hydroelastic Vibrations of Ships

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher; Folsø, Rasmus

    2002-01-01

    A formula for the necessary hull girder bending stiffness required to avoid serious springing vibrations is derived. The expression takes into account the zero crossing period of the waves, the ship speed and main dimensions. For whipping vibrations the probability of exceedance for the combined...

  17. Polar vessel hullform design based on the multi-objective optimization NSGA II

    Directory of Open Access Journals (Sweden)

    DUAN Fei

    2017-12-01

    Full Text Available [Objectives] With the increasing exploitation of the Arctic abundant oil and gas resources, a large number of ships which meet the polar navigational requirements are needed.[Methods] In this paper, the fast elitist Non-Dominated Sorting Genetic Algorithm (NSGA Ⅱ is applied to the hull optimization, and the multi-objective optimization method of polar vessel design is proposed. With the optimization goal of resistance and icebreaking resistance, filtering hull forms through the standard of polar vessel displacement and EEDI, fast ship hull optimization that satisfy the ice-ship dead weight and EEDI requirements has been achieved. Taking a 65 000 t shuttle tanker as an example, full parametric modeling method is adopted, the hull optimization of three different bow forms is conducted through the polar vessel multi-objective optimization method.[Results] The ship hull after optimization can satisfy the IA class navigation require, where the resistance in calm water decreases up to 12.94%, and the minimum propulsion power in ice field has a 27.36% reduction.[Conclusions] The feasibility and validity of the NSGA Ⅱ applying in polar vessel design is verified.

  18. Onboard monitoring of fatigue damage rates in the hull girder

    DEFF Research Database (Denmark)

    Nielsen, Ulrik Dam; Jensen, Jørgen Juncher; Pedersen, Preben Terndrup

    2011-01-01

    Most new advanced ships have extensive data collection systems to be used for continuous monitoring of engine and hull performance, for voyage performance evaluation etc. Such systems could be expanded to include also procedures for stress monitoring and for decision support, where the most...... critical wave-induced ship extreme responses and fatigue damage accumulation can be estimated for hypothetical changes in ship course and speed in the automatically estimated wave environment.The aim of this paper is to outline a calculation procedure for fatigue damage rate prediction in hull girders...... taking into account whipping stresses. It is conceptually shown how such a method, which integrates onboard estimation of sea states, can be used to deduce decision support with respect to the accumulated fatigue damage in the hull girder.The paper firstly presents a set of measured full-scale wave...

  19. Ships in an Artificial Force Field : A Multi-agent System for Nautical Traffic and Safety

    NARCIS (Netherlands)

    Xiao, F.

    2014-01-01

    The main objective of this research is developing a simulation tool that provides information of detailed ship behavior in a specific navigational environment, on both the ship traffic level and the individual ship level, for safety analysis, decision making, planning of ports and waterways, and

  20. Ship Detection in Optical Remote Sensing Images Based on Wavelet Transform and Multi-Level False Alarm Identification

    Directory of Open Access Journals (Sweden)

    Fang Xu

    2017-09-01

    Full Text Available Ship detection by Unmanned Airborne Vehicles (UAVs and satellites plays an important role in a spectrum of related military and civil applications. To improve the detection efficiency, accuracy, and speed, a novel ship detection method from coarse to fine is presented. Ship targets are viewed as uncommon regions in the sea background caused by the differences in colors, textures, shapes, or other factors. Inspired by this fact, a global saliency model is constructed based on high-frequency coefficients of the multi-scale and multi-direction wavelet decomposition, which can characterize different feature information from edge to texture of the input image. To further reduce the false alarms, a new and effective multi-level discrimination method is designed based on the improved entropy and pixel distribution, which is robust against the interferences introduced by islands, coastlines, clouds, and shadows. The experimental results on optical remote sensing images validate that the presented saliency model outperforms the comparative models in terms of the area under the receiver operating characteristic curves core and the accuracy in the images with different sizes. After the target identification, the locations and the number of the ships in various sizes and colors can be detected accurately and fast with high robustness.

  1. Total Analysis System for Ship Structural Strength

    OpenAIRE

    Takuya, Yoneya; Hiroyuki, Kobayashi; Abdul M., Rahim; Yoshimichi, Sasaki; Masaki, Irisawa; Technical Investigation and Information Department, Research Center; Technical Investigation and Information Department, Research Center; Singapore Office; Technical Investigation and Information Department, Research Center; Technical Investigation and Information Department, Research Center

    2001-01-01

    This paper outlines a total analysis system for ship hull structures, which integrates a wide variety of analysis functions to realise practical applications of rational methods for assessing ship structural strength. It is based on direct calculation of wave-induced loads as well as three-dimensional structural analysis of an entire-ship or hold structure. Three major analysis functions of the total system are ship motion and wave load analysis, ship structural analysis and statistical analy...

  2. Lightweight hull surface self-design vertical parameterization method based on NURBS

    Directory of Open Access Journals (Sweden)

    ZHANG Yanru

    2017-10-01

    Full Text Available [Objectives] At present, conventional design is limited to parent ship design space, and cannot drive ship hull design using as few parameters as possible. In order to solve the above problems, [Methods] by combining the draught function with NURBS, a ship hull surface self-design method based on vertical parameterization is proposed. In this method, the waterline is designated as the basic design unit; the bottom flat end line, designed waterline, stem and stern contours, side flat end line and maximum section line are designated as the characteristic constraints of the ship hull; and the draught function values corresponding to the characteristic parameters are designated as the design objectives. In this way, a waterline approximation model is built, and an evolutionary algorithm can be used to solve the approximation model. Finally, the ship hull surface is generated on the basis of the waterline using the NURBS skinning technique.[Results] The design examples of the characteristic curves of the full-scale ship hull surface indicate the practicable and advanced nature of this method.[Conclusions] The hull surface can be designed with as little data as possible using this method, making it much more suitable for the self-design of new ship forms.

  3. Measurement of leached hulls

    International Nuclear Information System (INIS)

    Reilly, T.D.

    1979-07-01

    Leached hulls are the short lengths of fuel rod cladding and fuel element hardware which constitute a major waste product of a reprocessing plant employing a chop-and-leach head-end process. The small, undissolved fuel residue (0.1 to 1.0% of original fuel content) which is discarded with this waste must be measured for safeguards, material accountability, and process control reasons. This report gives a critical analysis of hull measurement techniques involving the analysis of fission product gamma rays, spontaneous fission neutrons from curium, and delayed neutron activation. Major emphasis is given to the measurement of 2186-keV gamma rays from 144 Ce-- 144 Pr. A detailed description of typical leached hull characteristics is presented at the beginning of the report. An extensive review of experience gained from existing hull measurement systems in the United Kingdom, France, Japan, Germany, Italy, and the United States is presented

  4. Dynamic Planar Convex Hull

    DEFF Research Database (Denmark)

    Jacob, Riko

    We determine the computational complexity of the dynamic convex hull problem in the planar case. We present a data structure that maintains a finite set of n points in the plane under insertion and deletion of points in amortized O(log n) time per operation. The space usage of the data structure...... is O(n). The data structure supports extreme point queries in a given direction, tangent queries through a given point, and queries for the neighboring points on the convex hull in O(log n) time. The extreme point queries can be used to decide whether or not a given line intersects the convex hull......, and the tangent queries to determine whether a given point is inside the convex hull. The space usage of the data structure is O(n). We give a lower bound on the amortized asymptotic time complexity that matches the performance of this data structure....

  5. Computational methods for more fuel-efficient ship

    NARCIS (Netherlands)

    Koren, B.

    2008-01-01

    The flow of water around a ship powered by a combustion engine is a key factor in the ship's fuel consumption. The simulation of flow patterns around ship hulls is therefore an important aspect of ship design. While lengthy computations are required for such simulations, research by Jeroen Wackers

  6. On Rational Design of Double Hull Tanker Structures against Collision

    DEFF Research Database (Denmark)

    Paik, Jeom Kee; Chung, Jang Young; Choe, Ich Hung

    1999-01-01

    This paper is a summary of recent research and development in areas related to the design technology for double hull tanker structures against low energy collision, jointly undertaken by the Hyundai Heavy Industries, the American Bureau of Shipping, the Technical University of Denmark and the Pusan...... in the present study were (i) developing a framework for the collision design procedure for double hull tanker structures, (ii) experimental investigation of the structural crashworthiness of the collided vessels in collision or stranding, using double skinned structural models, (iii) validation of the special...... investigation of the energy absorption capability characteristics of a collided double hull VLCC side structure in collision, and (vi) development of a new modified Minorsky method for double hull tanker side structures. The tools developed and the results and insights obtained by the present study should...

  7. Dynamic Planar Convex Hull

    DEFF Research Database (Denmark)

    Brodal, Gerth Stølfting; Jacob, Rico

    2002-01-01

    In this paper we determine the computational complexity of the dynamic convex hull problem in the planar case. We present a data structure that maintains a finite set of n points in the plane under insertion and deletion of points in amortized O(log n) time per operation. The space usage of the d......In this paper we determine the computational complexity of the dynamic convex hull problem in the planar case. We present a data structure that maintains a finite set of n points in the plane under insertion and deletion of points in amortized O(log n) time per operation. The space usage...... of the data structure is O(n). The data structure supports extreme point queries in a given direction, tangent queries through a given point, and queries for the neighboring points on the convex hull in O(log n) time. The extreme point queries can be used to decide whether or not a given line intersects...... the convex hull, and the tangent queries to determine whether a given point is inside the convex hull. We give a lower bound on the amortized asymptotic time complexity that matches the performance of this data structure....

  8. 14 CFR 23.755 - Hulls.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hulls. 23.755 Section 23.755 Aeronautics... Hulls § 23.755 Hulls. (a) The hull of a hull seaplane or amphibian of 1,500 pounds or more maximum weight must have watertight compartments designed and arranged so that the hull auxiliary floats, and...

  9. Effective Hull IMMR plan

    Energy Technology Data Exchange (ETDEWEB)

    Franco, Mireille

    2010-07-01

    The objective of the Hull Inspection, Maintenance and Repair Plan is to ensure the total integrity of the Floating Production Unit. To be efficient, the Monitoring has to be part of the Hull Inspection, Monitoring, Maintenance and Repair Plan (IMMR). The IMMR Plan should be developed during the design and project phases and take into account the interfaces between the different systems and teams' tasks in operation. The IMMR is multidisciplinary and form part of the hand-over to ensure an efficient and early implementation. Implementation of such a complex plan requires: - Cross-functionality: take advantage of the synergies - Boldness: break the mould and think outside the box - Listening: be attentive, be available, - Mutual support: during good and bad times. This paper presents the way Total believe the Hull IMMR Plan shall be developed, implemented and followed up. (Author)

  10. Basin-Wide Maritime Awareness From Multi-Source Ship Reporting Data

    Directory of Open Access Journals (Sweden)

    Harm Greidanus

    2013-06-01

    Full Text Available A system was set up to ingest automatic ship position reports (terrestrial and satellite AIS, LRIT and fuse these into a Maritime Situational Picture, tracking the ships within an ocean basin-wide area of interest in real time. Trial runs were made over several months, collecting reporting data from a number of different sources, over the Gulf of Aden and the Western Indian Ocean. Also satellite radar surveillance was carried out in order to sample the presence of non-reporting ships. The trial showed that satellite AIS is a powerful tool for basin-wide ship traffic monitoring; that multiple AIS satellites are needed for sufficient completeness and update rate; and that coastal AIS and LRIT still provide essential complements to the satellite AIS data. The radar survey showed that about half of the radar-detected ships are not seen in the reporting data. The ultimate purpose of this work is to support the countries around the Horn of Africa in the fight against piracy and to help build their capacity to deliver maritime security and safety.

  11. SAR Image Simulation of Ship Targets Based on Multi-Path Scattering

    Science.gov (United States)

    Guo, Y.; Wang, H.; Ma, H.; Li, K.; Xia, Z.; Hao, Y.; Guo, H.; Shi, H.; Liao, X.; Yue, H.

    2018-04-01

    Synthetic Aperture Radar (SAR) plays an important role in the classification and recognition of ship targets because of its all-weather working ability and fine resolution. In SAR images, besides the sea clutter, the influence of the sea surface on the radar echo is also known as the so-called multipath effect. These multipath effects will generate some extra "pseudo images", which may cause the distortion of the target image and affect the estimation of the characteristic parameters. In this paper,the multipath effect of rough sea surface and its influence on the estimation of ship characteristic parameters are studied. The imaging of the first and the secondary reflection of sea surface is presented . The artifacts not only overlap with the image of the target itself, but may also appear in the sea near the target area. It is difficult to distinguish them, and this artifact has an effect on the length and width of the ship.

  12. Numerical simulation of hydrodynamic performance of ship under oblique conditions

    Directory of Open Access Journals (Sweden)

    CHEN Zhiming

    2018-02-01

    Full Text Available [Objectives] This paper is intended to study the viscous flow field around a ship under oblique conditions and provide a research basis for ship maneuverability. [Methods] Using commercial software STRA-CCM+, the SST k-ω turbulence model is selected to predict the hydrodynamic performance of the KVLCC2 model at different drift angles, and predict the hull flow field. The pressure distribution of the ship model at different drift angles is observed and the vortex shedding of the ship's hull and constraint streamlines on the hull's surface are also observed. [Results] The results show that numerical simulation can satisfy the demands of engineering application in the prediction of the lateral force, yaw moment and hull surface pressure distribution of a ship. [Conclusions] The research results of this paper can provide valuable references for the study of the flow separation phenomenon under oblique conditions.

  13. Estimation of hull girder vertical bending moments including non-linear and flexibility effects using closed form expressions

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup; Jensen, Jørgen Juncher

    2009-01-01

    A simple but rational procedure for prediction of extreme wave-induced hull girder bending moment is presented. The procedure takes into account main ship hull characteristics such as: length, breadth, draught, block coefficient, bow flare coefficient, forward speed and hull flexibility. The wave......-linear strip theory calculations and supplemented with new closed form results for the hogging bending moment. Focus is on the extreme hull girder hogging bending moment. Due to the few input parameters this procedure can be used to estimate the wave-induced bending moments at the conceptual design phase....... Another application area is for novel single hull ship types not presently covered by the rules of the classification societies. As one application example the container ship M/S Napoli is considered....

  14. Infrared ship signature analysis and optimisation

    NARCIS (Netherlands)

    Neele, F.P.

    2005-01-01

    The last decade has seen an increase in the awareness of the infrared signature of naval ships. New ship designs show that infrared signature reduction measures are being incorporated, such as exhaust gas cooling systems, relocation of the exhausts and surface cooling systems. Hull and

  15. Performance Monitoring of Ships

    DEFF Research Database (Denmark)

    Hansen, Søren Vinther

    is used as input to the system and by comparing model and ship behaviour, an index describing the ship’s performance is generated. The work in this thesis is based on data logged through the automation system on board a PostPanmax container ship where data have been logged through a year. A routine...... in the models have been identified. The models used in this work are based on empirical relations or based on regression analyses of model tests and full-scale trials. In order to achieve valid results the conditions where performance is estimated have to be inside the boundaries of the model. Filters have been......The purpose of the research project is to establish a reliable index in the performance evaluation of ships. During operation the ship will experience added resistance due to fouling of hull and propeller. The added resistance will lead to increased fuel consumption and thus increased emissions...

  16. Review of ship slamming loads and responses

    Science.gov (United States)

    Wang, Shan; Guedes Soares, C.

    2017-12-01

    The paper presents an overview of studies of slamming on ship structures. This work focuses on the hull slamming, which is one of the most important types of slamming problems to be considered in the ship design process and the assessment of the ship safety. There are three main research aspects related to the hull slamming phenomenon, a) where and how often a slamming event occurs, b) slamming load prediction and c) structural response due to slamming loads. The approaches used in each aspect are reviewed and commented, together with the presentation of some typical results. The methodology, which combines the seakeeping analysis and slamming load prediction, is discussed for the global analysis of the hull slamming of a ship in waves. Some physical phenomena during the slamming event are discussed also. Recommendations for the future research and developments are made.

  17. Modeling Liner Shipping Service Selection and Container Flows using a Multi-layer Network

    DEFF Research Database (Denmark)

    Karsten, Christian Vad; Balakrishnan, Anant

    We introduce a new formulation for the tactical planning problem facing container shipping companies of selecting the best subset of sailing routes from a given pool of candidate routes so as to maximize profit. Since most containers are sent directly or transshipped at most twice in current liner...

  18. Free-surface flow around an appended hull

    International Nuclear Information System (INIS)

    Lungu, A; Pacuraru, F

    2010-01-01

    The prediction of the total drag experienced by an advancing ship is a complicated problem which requires a thorough understanding of the hydrodynamic forces acting on the hull, the physical processes from which these forces arise as well as their mutual interaction. A general numerical method to predict the hydrodynamic performance of a twin-propeller combatant ship is presented in the paper, which describes the solution of a RANS solver coupled with a body force method as an attempt in investigating the flow features around the ship hull equipped with rotating propellers and rudders. A special focus is made on the propeller non-symmetrical inflow field, aimed at obtaining the necessary data for the propulsive performances evaluation as well as for the propeller final design. The reported work allows not only the performance evaluation for the overall performances of a hull, but also leads to the development, implementation and validation of new concepts in modeling the turbulent vortical flows, with direct connection to the ship propulsion problem.

  19. On the collision protection of ships

    International Nuclear Information System (INIS)

    Jones, N.

    1976-01-01

    A brief survey of the literature extant on the collision protection of ships is presented herein. An examination of the characteristics of different energy-absorbing methods suggests that honeycomb structures provide an alternative to deck structures which are currently used to achieve the collision protection of ships. Various features of honeycomb panels are explored and a particular structural arrangement which utilizes both sides of a hull and incorporates honeycomb panels is proposed for the collision protection of a ship. (Auth.)

  20. The multi-element ultrasonic technology: examples of application on military naval structures

    International Nuclear Information System (INIS)

    Recolin, P.; Rivalin, S.

    2009-01-01

    DCNS is the European leader in the military ship construction and maintenance (conventional and nuclear propulsion). The potential of ultrasonic technologies with multi-element probes has been studied in its Materials laboratory since the end of the 80's, and a growing number of applications has appeared these last ten years. A series of examples is given: in-service nuclear reactor pipe welds monitoring, time-of-flight diffraction (TOFD) technique for the inspection of containment welds, coating fabrication control, detection of laminating corrosion on aluminum rings, detection of corrosion on submarine hulls in basin, inspection of hull welded joints

  1. Hull Girder Fatigue Damage Estimations of a Large Container Vessel by Spectral Analysis

    DEFF Research Database (Denmark)

    Andersen, Ingrid Marie Vincent; Jensen, Jørgen Juncher

    2013-01-01

    This paper deals with fatigue damage estimation from the analysis of full-scale stress measurements in the hull of a large container vessel (9,400 TEU) covering several months of operation. For onboard decision support and hull monitoring sys-tems, there is a need for a fast reliable method...... for esti-mation of fatigue damage in the ship hull. The objective of the study is to investigate whether the higher frequency contributions from the hydroelastic responses (springing and whipping) can satisfactory be included in the fatigue damage estimation by only a few parameters derived from the stress...

  2. 46 CFR 167.15-20 - Inspections of nautical school ships.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Inspections of nautical school ships. 167.15-20 Section... NAUTICAL SCHOOL SHIPS Inspections § 167.15-20 Inspections of nautical school ships. (a) At each annual inspection, or oftener if deemed necessary, the inspector will inspect the hull, boilers, machinery...

  3. 14 CFR 25.755 - Hulls.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hulls. 25.755 Section 25.755 Aeronautics... STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Floats and Hulls § 25.755 Hulls. (a) Each hull must have enough watertight compartments so that, with any two adjacent compartments flooded, the...

  4. 14 CFR 29.755 - Hull buoyancy.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull buoyancy. 29.755 Section 29.755... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Floats and Hulls § 29.755 Hull buoyancy. Water-based and amphibian rotorcraft. The hull and auxiliary floats, if used, must have enough...

  5. The interaction of extreme waves with hull elements

    Science.gov (United States)

    Galiev, Shamil; Flay, Richard

    2010-05-01

    the effect of the hull cavitation. The function PIC or 0, and is determined during the numerical calculations. Case PIC is valid for the case with no cavitation, and the case δ(r,t) = 0 corresponds to the case with hull cavitation. The results from these calculations allow us to draw the following conclusions. 1) The pressures generated depend greatly on the irregularity of waves. In particular, the shock pressures are affected by this irregularity, making the prediction of their magnitude almost impossible. 2) In the majority of cases, the elastic deformation of thin hull elements by a short duration water wave pressure pulse is accompanied by hull cavitation. The effect of cavitation may be important, provided that the time of loading by the water wall pressure is less than the period of the fundamental frequency of the hull element oscillations. 3) The cavitation zones can enclose practically the whole wet surface and thus completely change the water loading onto the hull element, compared to the pressures that would be developed in the absence of cavitation. 4) The hull element deformation generates surface pressure and cavitation waves. 5) Cavitation interaction of extreme water waves with structures, and hull response, are complex topics, which are not well understood and are expected to be important in the design of advanced ships in the future. 6) The existence of rogue waves makes it important to re-examine some of the ideas developed earlier which are fundamental to merchant ship design.

  6. Hospital Ship Replacement

    Science.gov (United States)

    2011-08-01

    serious contender. Although it is a proven hull design for stability, integrating the ability to quickly transfer patients aboard is challenging . The...Waste management afloat is a constant challenge for the Navy. It is even more so when designing a hospital ship. In addition to the typical waste...0.97 Optbrs: Corrmon rail fuellrijacllon,crude oil. Rated power generating sets 61:ili:ln()q;to~ 50Htl760rpm &.gne type -1801.\\ Vlc )l ~W.’/cyl SI;O k

  7. Design of high-speed planing hulls for the improvement of resistance and seakeeping performance

    Directory of Open Access Journals (Sweden)

    Dong Jin Kim

    2013-03-01

    Full Text Available High-speed vessels require good resistance and seakeeping performance for safe operations in rough seas. The resistance and seakeeping performance of high-speed vessels varies significantly depending on their hull forms. In this study, three planing hulls that have almost the same displacement and principal dimension are designed and the hydrodynamic characteristics of those hulls are estimated by high-speed model tests. All model ships are deep-V type planing hulls. The bows of no.2 and no.3 model ships are designed to be advantageous for wave-piercing in rough water. No. 2 and no. 3 model ships have concave and straight forebody cross-sections, respectively. And length-to-beam ratios of no.2 and no.3 models are larger than that of no.1 model. In calm water tests, running attitude and resistance of model ships are measured at various speeds. And motion tests in regular waves are performed to measure the heave and pitch motion responses of the model ships. The required power of no.1 (VPS model is smallest, but its vertical motion amplitudes in waves are the largest. No.2 (VWC model shows the smallest motion amplitudes in waves, but needs the greatest power at high speed. The resistance and seakeeping performance of no.3 (VWS model ship are the middle of three model ships, respectively. And in regular waves, no.1 model ship experiences ‘fly over’ phenomena around its resonant frequency. Vertical accelerations at specific locations such as F.P., center of gravity of model ships are measured at their resonant frequency. It is necessary to measure accelerations by accelerometers or other devices in model tests for the accurate prediction of vertical accelerations in real ships.

  8. Hydrodynamic design of an underwater hull cleaning robot and its evaluation

    Directory of Open Access Journals (Sweden)

    Man Hyung Lee

    2012-12-01

    Full Text Available An underwater hull cleaning robot can be a desirable choice for the cleaning of large ships. It can make the cleaning process safe and economical. This paper presents a hydrodynamic design of an underwater cleaning robot and its evaluation for an underwater ship hull cleaning robot. The hydrodynamic design process of the robot body is described in detail. Optimal body design process with compromises among conflicting design requirements is given. Experimental results on the hydrodynamic performance of the robot are given.

  9. Analysis of a ship-to-ship collision

    International Nuclear Information System (INIS)

    Porter, V.L.; Ammerman, D.J.

    1996-01-01

    Sandia National Laboratories is involved in a safety assessment for the shipment of radioactive material by sea. One part of this study is investigation of the consequences of ship-to-ship collisions. This paper describes two sets of finite element analyses performed to assess the structural response of a small freighter and the loading imparted to radioactive material (RAM) packages during several postulated collision scenarios with another ship. The first series of analyses was performed to evaluate the amount of penetration of the freighter hull by a striking ship of various masses and initial velocities. Although these analyses included a representation of a single RAM package, the package was not impacted during the collision so forces on the package could not be computed. Therefore, a second series of analyses incorporating a representation of a row of seven packages was performed to ensure direct package impact by the striking ship. Average forces on a package were evaluated for several initial velocities and masses of the striking ship. In addition to. providing insight to ship and package response during a few postulated ship collisions scenarios, these analyses will be used to benchmark simpler ship collision models used in probabilistic risk assessment analyses

  10. Observations and computations of narrow Kelvin ship wakes

    Directory of Open Access Journals (Sweden)

    Francis Noblesse

    2016-01-01

    Full Text Available Computations of far-field ship waves, based on linear potential flow theory and the Hogner approximation, are reported for monohull ships and catamarans. Specifically, far-field ship waves are computed for six monohull ships at four Froude numbers F≡V/gL=0.58, 0.68, 0.86, 1.58 and for six catamarans with nondimensional hull spacing s≡S/L=0.25 at two Froude numbers Fs≡V/gS=1 and 2.5. Here, g is the gravitational acceleration, V and L denote the ship speed and length, and S is the separation distance between the twin hulls of a catamaran. The computations show that, although the amplitudes of the waves created by a ship are strongly influenced by the shape of the ship hull, as well known, the ray angles where the largest waves are found are only weakly influenced by the hull shape and indeed are mostly a kinematic feature of the flow around a ship hull. An important practical consequence of this flow feature is that the apparent wake angle of general monohull ships or catamarans (with arbitrarily-shaped hulls can be estimated, without computations, by means of simple analytical relations; these relations, obtained elsewhere via parametric computations, are given here. Moreover, the influence of the two parameters Fs and s that largely determine the ray angles of the dominant waves created by a catamaran is illustrated via computations for three catamarans with hull spacings s=0.2, 0.35, 0.5 at four Froude numbers Fs=1, 1.5, 2, 2.5. These computations confirm that the largest waves created by wide and/or fast catamarans are found at ray angles that only depend on Fs (i.e. that do not depend on the hull spacing s in agreement with an elementary analysis of lateral interference between the dominant waves created by the bows (or sterns of the twin hulls of a catamaran. The dominant-waves ray angles predicted by the theory of wave-interference effects for monohull ships and catamarans are also compared with the observations of narrow Kelvin ship

  11. Effect of Buffer Bow Structure in Ship-Ship Collision

    DEFF Research Database (Denmark)

    Yamada, Yasuhira; Endo, Hisayoshi; Pedersen, Preben Terndrup

    2008-01-01

    tankers, the introduction of buffer bulbous bows has been proposed. Relatively soft buffer bows absorb part of the kinetic energy of the striking ship before penetrating the inner hull of the struck vessel. The purpose of the present paper is to verify the effectiveness of a prototype buffer bulbous bow......) and the forward velocity of the struck ship on the collapse mode of the bow of the striking vessel are investigated. Collapse modes, contact forces and energy absorption capabilities of the buffer bows are compared with those of conventional bows....

  12. Double hull oil tankers - how effective are they?

    International Nuclear Information System (INIS)

    Keith, V.F.

    1993-01-01

    The groundings of the Exxon Valdez on Bligh Reef in Prince William Sound, spilling more than 10 million gallons of Alaska North Slope crude, and the American Trader off Huntington Beach, spilling almost 400,000 gallons of Alaska North Slope crude, suggest that the construction of oil tankers be re-examined with respect to a design which could reduce both the number and magnitude of oil spills. This paper discusses state-of-the-art tanker technology with respect to spill prevention, effectiveness, and cost. The design features include double hulls, centralized bunker tankers, vacuum-retaining valves, cargo control systems, auxiliary thrusters, electronic charting, and the retransmission of the ship's position. Double hulls provide the highest probability of surviving damage, either from a collision or grounding, with no loss of cargo. Use of double hulls can reduce oil spill incidence by 90 percent in grounding situations and by 75 percent in collisions. The oil spill from the AmericanTrader could have been completely avoided by double hull construction. The arrangement provides spaces below the cargo tanks and on the vessel's sides solely for the carriage of ballast water when the tanker is in ballast condition. These tanks are empty when the tanker is loaded and then also act as the first line of defense in the event of structural damage to the cargo tanks. Tanker design is integrated with port safety measures, including vessel monitoring systems, in this total spill prevention analysis. All aspects of the tanker transportation system are considered

  13. Solving multi-product inventory ship routing with a heterogeneous fleet model using a hybrid cross entropy-genetic algorithm: a case study in Indonesia

    Directory of Open Access Journals (Sweden)

    Budi Santosa

    2016-01-01

    Full Text Available This paper presents a model and an algorithm for an inventory ship routing problem (ISRP. It consists of two main parts: a model development of the ship routing problem in a multi-product inventory with a heterogeneous fleet and an algorithm development to solve the problem. The problem is referred to as ISRP. ISRP considers several parameters including the deadweight tonnage (DWT, product compatibility, port setup, and compartment washing costs. Considering these parameters, the objective function is to minimize the total cost, which consists of traveling, port setup, ship charter, and compartment washing costs. From the resulting model, there are two major steps used to solve the problem. The first is to select the ships in order to satisfy the constraint that restricts the mooring rule. The second is to find the best route, product allocation, and shipped quantity. ISRP is an Non Polynomial-hard problem. Finding the solution of such problem needs a high computation time. A new hybrid metaheuristics, namely the cross entropy-genetic algorithm (CEGA, was proposed to solve ISRP. The results were then compared with those resulted from a hybrid Tabu Search to measure the hybrid CEGA performance. The results showed that CEGA provided better solutions than those produced by the hybrid Tabu Search.

  14. Development of hull compaction system for nuclear recycle facility

    International Nuclear Information System (INIS)

    Manole, A.A.; Karkhanis, P.P.; Agarwal, Kailash; Basu, Sekhar

    2013-01-01

    India has adopted closed fuel cycle strategy for efficient management of available resources to meet long term energy requirements. Nuclear Recycle Facility (NRF) provides a vital link in three-stage Indian nuclear power programme. In a NRF for PHWR fuel cycle, reprocessing of spent fuel bundles from PHWRs is carried out using a chop-leach process where the spent fuel bundles are chopped into small pieces using a spent fuel chopper and the contents inside the zircaloy clad are dissolved using concentric nitric acid. This process generates empty zircaloy shells called 'hulls'. The present practice followed for management of hulls is to transfer them into SS drums and store these drums in underground RCC tile holes at a Waste Management Facility (WMF). This waste needs to be stored in an engineered WMF for at least 30-60 years before transferred to a final repository. The storage volumes required for this hull waste will keep increasing as the reprocessing capacity is being enhanced multi-folds. Compaction of hull waste has been employed internationally to reduce the volume required for storage. Hence indigenous development of hull compaction system was initiated by NRB to meet the future requirements. This is being achieved through a set of experiments and analysis with the available resources within the country. This paper describes the process of compaction, conceptualization of the system and benefits accrued from it. (author)

  15. Wave-induced hydroelastic response of fast monohull displacement ships

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher; Wang, Zhaohui

    1998-01-01

    High-speed ships are weight sensitive structures and high strength steel, aluminium or composites are preferred building materials. It is characteristic for these materials that they result in larger hull flexibility than more conventional materials. Therefore, for large fast ships the lowest...

  16. Strength of Ship Stiffened Panels under Combined Loading

    DEFF Research Database (Denmark)

    Weicheng, Cui; Wang, Young-jun; Pedersen, Preben Terndrup

    2000-01-01

    A ship's hull is a box girder structure composed of stiffened panels and therefore, strength of stiffened panels plays a significant role for the ultimate strength analysis of ship structures. In recent years several authors have proposed simplified methods to calculate the ultimate strength of s...

  17. Engineering Hydrodynamic AUV Hulls

    Science.gov (United States)

    Allen, J.

    2016-12-01

    AUV stands for autonomous underwater vehicle. AUVs are used in oceanography and are similar to gliders. MBARIs AUVs as well as other AUVs map the ocean floor which is very important. They also measure physical characteristics of the water, such as temperature and salinity. My science fair project for 4th grade was a STEM activity in which I built and tested 3 different AUV bodies. I wanted to find out which design was the most hydrodynamic. I tested three different lengths of AUV hulls to see which AUV would glide the farthest. The first was 6 inches. The second was 12 inches and the third was 18 inches. I used clay for the nosecone and cut a ruler into two and made it the fin. Each AUV used the same nosecone and fin. I tested all three designs in a pool. I used biomimicry to create my hypothesis. When I was researching I found that long slim animals swim fastest. So, my hypothesis is the longer AUV will glide farthest. In the end I was right. The longer AUV did glide the farthest.

  18. On the Effect of Hull Girder Flexibility on the Vertical Wave Bending Moment for Ultra Large Container Vessels

    DEFF Research Database (Denmark)

    Andersen, Ingrid Marie Vincent; Jensen, Jørgen Juncher

    2012-01-01

    Currently, a number of very large container ships are being built and more are on order, and some concerns have been expressed about the importance of the reduced hull girder stiffness to the wave-induced loads. The main concern is related to the fatigue life, but also a possible increase...... in the global hull girder loads as consequence of the increased hull flexibility must be considered. This is especially so as the rules of the classification societies do not explicitly account for the effect of hull flexibility on the global loads. In the present paper an analysis has been carried out...... in the waves. Slamming forces are determined by a standard momentum formulation. The hull flexibility is modelled as a nonprismatic Timoshenko beam. Generally, good agreement with experimental results and more accurate numerical predictions has previously been obtained in a number of studies. The statistical...

  19. Simple Assessment of Post-Grounding Loads and Strength of Ships

    DEFF Research Database (Denmark)

    Paik, Jeom Kee; Pedersen, Preben Terndrup

    1997-01-01

    The aim of the present study is to determine the sectional forces induced by the ship grounding and also to assess the residual strength of grounded ship hulls. An analytical approach is used to estimate the grounding- induced sectional forces of ships. The extent and location of structural damage...

  20. Strength Tests on Hulls and Floats

    Science.gov (United States)

    Matthaes, K

    1942-01-01

    The present report deals with strength tests on hulls and floats intended in part for the collection of construction data for the design of these components and in part for the stress analysis of the finished hulls and floats.

  1. Integrating SHM and Time Variant System Performance of Naval Ship Structures For Near Real Time Decision Making Under Uncertainty: A Comprehensive Framework

    Science.gov (United States)

    2016-12-06

    performance of damaged ships. Reducing risk associated with loss of ship due to a post-accident collapse or disintegration of the hull during tow or rescue...In order to allow small regions of the hull extremities to plastify, it is assumed that the plasticized area is located within the extreme plates and...the damage is based on the percentage of plasticized area within the considered hull section. Therefore, the damage ratios associated with each

  2. Observations and computations of narrow Kelvin ship wakes

    OpenAIRE

    Francis Noblesse; Chenliang Zhang; Jiayi He; Yi Zhu; Chenjun Yang; Wei Li

    2016-01-01

    Computations of far-field ship waves, based on linear potential flow theory and the Hogner approximation, are reported for monohull ships and catamarans. Specifically, far-field ship waves are computed for six monohull ships at four Froude numbers F≡V/gL=0.58, 0.68, 0.86, 1.58 and for six catamarans with nondimensional hull spacing s≡S/L=0.25 at two Froude numbers Fs≡V/gS=1 and 2.5. Here, g is the gravitational acceleration, V and L denote the ship speed and length, and S is the separation di...

  3. Design of Crashworthy Ship Strucures

    DEFF Research Database (Denmark)

    Toernqvist, Rikard

    2003-01-01

    The main purpose of the project has been to develop a rational procedure for designing new crashworthy side structures for those ship types where it could be expected that a substantial improvement of the crashworthiness and the related safety could be achieved by careful consideration of the str......The main purpose of the project has been to develop a rational procedure for designing new crashworthy side structures for those ship types where it could be expected that a substantial improvement of the crashworthiness and the related safety could be achieved by careful consideration...... in collision and grounding analysis is the prediction of the onset of fracture and crack propagation in the shell plating. In simulations of accidental loading on ships it is crucial that fracture is determined correctly, as it will influence the global deformation mode and the amount of damage to the hull...

  4. Antifouling Effectiveness of Copolymers for Ship Hull Protection

    Science.gov (United States)

    1993-01-01

    methanol was added dropwise in dim light to the stirred tetraor- ganotin suspension (Rosenberg, Debreczeni, & Weinberg, 1959; Boue , Gielen...Nasielski, 1968; Boue et al., 1969). Upon completion of the reaction, the solvent and low-boiling side products were removed under vaccum at room temperature...organisms, the released species has a minimal impact on the environment. 13 REFERENCES Boue , S., M. Gielen, and J. Nasielski. 1968. "Organometallic

  5. Logistical Analysis of the Littoral Combat Ship

    National Research Council Canada - National Science Library

    Rudko, David

    2003-01-01

    The purpose of the Littoral Combat Ship (LCS) is to provide the Navy with an affordable, small, multi-mission ship capable of independent, interdependent, and integrated operations inside the littorals...

  6. INFLUENCE OF OPERABILITY CRITERIA LIMITING VALUES ON SHIP SPEED

    Directory of Open Access Journals (Sweden)

    Jasna Prpić-Oršić

    2016-09-01

    Full Text Available When the ship is caught in heavy seas, there are two manoeuvres that the shipmaster can undertake to avoid excessive ship motion and hull damage: changing course or voluntary speed reduction. This paper presents a study of the effect of the various voluntary speed reduction criteria to attainable speed of ship on seaway. The speed loss is calculated by taking into account wind and wave effect on ship speed, the engine and propeller performance in actual seas as well as the mass inertia of the ship. The attainable ship speed for ship in head, following and beam waves by accounting for voluntary speed reduction is estimated for various significant wave height. The criteria of slamming, deck wetness, propeller emergence, excessive accelerations and roll are taken into account. The impact of variations of the limiting values of certain criteria due to which the captain intentionally reduces the ship speed is analysed and discussed.

  7. Ship design methodologies of preliminary design

    CERN Document Server

    Papanikolaou, Apostolos

    2014-01-01

    This book deals with ship design and in particular with methodologies of the preliminary design of ships. The book is complemented by a basic bibliography and five appendices with useful updated charts for the selection of the main dimensions and other basic characteristics of different types of ships (Appendix A), the determination of hull form  from the data of systematic hull form series (Appendix B), the detailed description of the relational method for the preliminary estimation of ship weights (Appendix C), a brief review of the historical evolution of shipbuilding science and technology from the prehistoric era to date (Appendix D) and finally a historical review of regulatory developments of ship's damage stability to date (Appendix E).  The book can be used as textbook for ship design courses or as additional reading for university or college students of naval architecture courses and related disciplines; it may also serve as a reference book for naval architects, practicing engineers of rel...

  8. Decommission of nuclear ship 'MUTSU'

    International Nuclear Information System (INIS)

    Tateyama, Takeshi

    1996-01-01

    The nuclear-powered ship 'MUTSU' was decommissioned by removing the reactor room in June 1995, which was hoisted and transported by a floating crane to a shore storage room at Sekinehama, Aomori Prefecture. This work was carried out in three stages: extraction of the spent fuel assemblies and neutron sources, dismantling of the machinery in the reactor auxiliary room, and separation and transportation of the reactor together with the secondary shielding structure and surrounding hull. IHI mainly conducted the third stage work. The separation work of the reactor room structure using a semisubmersible barge is outlined. Stress analysis and design of the reactor room for lifting work is also described. (author)

  9. Static analysis of the hull plate using the finite element method

    Science.gov (United States)

    Ion, A.

    2015-11-01

    This paper aims at presenting the static analysis for two levels of a container ship's construction as follows: the first level is at the girder / hull plate and the second level is conducted at the entire strength hull of the vessel. This article will describe the work for the static analysis of a hull plate. We shall use the software package ANSYS Mechanical 14.5. The program is run on a computer with four Intel Xeon X5260 CPU processors at 3.33 GHz, 32 GB memory installed. In terms of software, the shared memory parallel version of ANSYS refers to running ANSYS across multiple cores on a SMP system. The distributed memory parallel version of ANSYS (Distributed ANSYS) refers to running ANSYS across multiple processors on SMP systems or DMP systems.

  10. 33 CFR 110.31 - Hull Bay and Allerton Harbor at Hull, Mass.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Hull Bay and Allerton Harbor at Hull, Mass. 110.31 Section 110.31 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.31 Hull Bay and Allerton Harbor at...

  11. The cost calculus model for the hull roughness; Um modelo para calculo do custo da rugosidade do casco

    Energy Technology Data Exchange (ETDEWEB)

    Marco, Antonino Di [International Paint (Akzo Nobel Ltda.), Sao Paulo, SP (Brazil)

    2004-07-01

    The economic importance of the condition of the immersed hull cannot be underestimated; any increase of the roughness may result in a significant increase in the operational costs of a ship. There are two main types of roughness, biological and physical, each one with its proper characteristics of macro and micro roughness; when an increase in the roughness of the underwater hull occurs, the frictional resistance of the ship or .drag. also increases, resulting in additional power and consequent increase of the fuel consumption to keep the speed of the ship. Keeping the power constant will result in lower speed and greater voyage times. Aiming the better understanding of the effect of the roughness in the performance, costs and operational efficiency of a ship, International Paint developed a new model called 'Hull Roughness Penalty Calculator', a program that predicts the increase of the hull roughness during in service time specified service and combines it with the fouling risk associated with different types of antifoulings. The model compares fuel consumptions and costs of different types of TBT free antifoulings to derive the potential benefit, and also can be used to compare the emissions of carbon dioxide and sulphur oxides. (author)

  12. Superconducting DC homopolar motors for ship propulsion

    Energy Technology Data Exchange (ETDEWEB)

    Heiberger, M.; Reed, M.R.; Creedon, W.P.; O' Hea, B.J. [General Atomic (United States)

    2000-07-01

    Superconducting DC homopolar motors have undergone recent advances in technology, warranting serious consideration of their use for ship propulsion. Homopolar motor propulsion is now practical because of two key technology developments: cryogen-free superconducting refrigeration and high performance motor fiber brushes. These compact motors are ideal for podded applications, where reduced drag and fuel consumption are predicted. In addition, the simple DC motor controller is more efficient and reliable compared with AC motor controllers. Military ships also benefit from increased stealth implicit in homopolar DC excitation, which also allows the option for direct hull or pod mounting. (authors)

  13. Load and Global Response of Ships

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher

    The present monograph covers wave load and global structural response for ships. It is primary written as a textbook for students with an introductionary background in naval architecture and a basic knowledge of statistics and strength of materials. The subjects are treated in details starting from...... first principles. The aim has been to derive and present the necessary theoretical framework for predicting the extreme loads and the corresponding hull girder stresses the ship may be subjected to during its operational lifetime.Although some account is given to reliabiity analysis, the present...

  14. Shipping Fairways

    Data.gov (United States)

    Department of Homeland Security — Various shipping zones delineate activities and regulations for marine vessel traffic. Traffic lanes define specific traffic flow, while traffic separation zones...

  15. 75 FR 10546 - Shipping Coordinating Committee; Notice of Committee Meeting

    Science.gov (United States)

    2010-03-08

    ... prevent explosions on oil and chemical tankers transporting low flash point cargoes --Clarification of... on evacuation analysis for new and existing passenger ships --Consideration of IACS unified interpretations --Fixed hydrocarbon gas detection systems on double-hull tankers --Harmonization of the...

  16. 14 CFR 29.757 - Hull and auxiliary float strength.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and auxiliary float strength. 29.757... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Floats and Hulls § 29.757 Hull and auxiliary float strength. The hull, and auxiliary floats if used, must withstand the...

  17. 21 CFR 573.160 - Ammoniated rice hulls.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Ammoniated rice hulls. 573.160 Section 573.160... Additive Listing § 573.160 Ammoniated rice hulls. The food additive ammoniated rice hulls may be safely... obtained by the treatment of ground rice hulls with monocalcium phosphate and anhydrous ammonia at a...

  18. Study of multi-nucleon transfer reactions in {sup 58,} {sup 64}Ni + {sup 207}Pb collisions at the velocity filter SHIP

    Energy Technology Data Exchange (ETDEWEB)

    Comas, V.F.; Heinz, S.; Ackermann, D.; Heredia, J.A.; Hessberger, F.P.; Khuyagbaatar, J.; Kindler, B.; Lommel, B.; Mann, R. [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, Darmstadt (Germany); Hofmann, S. [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, Darmstadt (Germany); Goethe-Universitaet Frankfurt, Institut fuer Physik, Frankfurt (Germany)

    2013-09-15

    We investigated multi-nucleon transfer reactions in collisions of {sup 58}Ni + {sup 207}Pb and {sup 64}Ni + {sup 207}Pb at Coulomb barrier energies. The new aspect is that we used a velocity filter (SHIP at GSI) for the separation of the heavy target-like transfer products from background events. The isotopic identification was performed via the {alpha} decay properties of the reaction products. The goal of the experiment was to study the characteristics of multi-nucleon transfer reactions in the region of heavy nuclei and the applicability of existing separation and detection techniques, which are usually used for identification of heavy fusion-evaporation residues, to heavy transfer products. This was motivated by recent theoretical results from macroscopic-microscopic models which suggest deep inelastic transfer reactions in heavy systems as a means to produce new neutron-rich isotopes in the region of N = 126 and in the region of superheavy nuclei. In this paper we present the isotopic yields, the excitation functions and the excitation energies of the heavy transfer products with Z > 82 as well as the influence of shell effects on the reaction products. The influence of the different neutron numbers of the projectiles is also discussed. (orig.)

  19. Full Scale Measurements of the Hydro-Elastic Response of Large Container Ships for Decision Support

    DEFF Research Database (Denmark)

    Andersen, Ingrid Marie Vincent

    scale measurements from four container ships of 4,400 TEU, 8,600 TEU, 9,400 TEU and 14,000 TEU Primarily, strains measured near the deck amidships are used. Furthermore, measurements of motions and the encountered sea state are available for one of the ships. The smallest ship is in operation...... frequency with the waves. Together with the relatively high design speed and often pronounced bow flare this makes large container ship more sensitive to slamming and, consequently, the effects of wave-induced hull girder vibrations. From full scale strain measurements of individual, measured hull girder......The overall topic of this thesis is decision support for operation of ships and several aspects are covered herein. However, the main focus is on the wave-induced hydro-elastic response of large container ships and its implications on the structural response. The analyses are based mainly on full...

  20. A new approach to hull consistency

    Directory of Open Access Journals (Sweden)

    Kolev Lubomir

    2016-06-01

    Full Text Available Hull consistency is a known technique to improve the efficiency of iterative interval methods for solving nonlinear systems describing steady-states in various circuits. Presently, hull consistency is checked in a scalar manner, i.e. successively for each equation of the nonlinear system with respect to a single variable. In the present poster, a new more general approach to implementing hull consistency is suggested which consists in treating simultaneously several equations with respect to the same number of variables.

  1. Test Ship

    Data.gov (United States)

    Federal Laboratory Consortium — The U. S. Navy dedicated the decommissioned Spruance Class destroyer ex-PAUL F. FOSTER (EDD 964), Test Ship, primarily for at sea demonstration of short range weapon...

  2. Ship for the cleaning of water from oil, fuel oil, and other floating objects

    Energy Technology Data Exchange (ETDEWEB)

    Nentvih, V

    1969-12-31

    The newly designed ship for the cleaning of water surface from floating pollution has its bow section built much lower than its main hull. A slanted platform leads to a channel guiding the water into a centrifuge which separates oil from water. Oil proceeds to a reservoir for reprocessing while water is discharged from the ship. A variable ballast controls the depth of submersion of the platform. The ship is equilibrated by means of a built-in air float.

  3. Numerical Study on the Effect of Buffer Bow Structure in Ship-to-ship Collisions

    DEFF Research Database (Denmark)

    Yamada, Yasuhira; Endo, Hisayoshi; Pedersen, Preben Terndrup

    2005-01-01

    tankers, the introduction of buffer bulbous bows has been proposed. Relatively soft buffer bows absorb part of the kinetic energy of the striking ship before penetrating the inner hull of the struck vessel. The purpose of the present paper is to verify the effectiveness of a prototype buffer bulbous bow......) and the forward velocity of the struck ship on the collapse mode of the bow of the striking vessel are investigated. Collapse modes, contact forces and energy absorption capabilities of the buffer bows are compared with those of conventional bows....

  4. A Fully Nonlinear, Dynamically Consistent Numerical Model for Solid-Body Ship Motion. I. Ship Motion with Fixed Heading

    Science.gov (United States)

    Lin, Ray-Quing; Kuang, Weijia

    2011-01-01

    In this paper, we describe the details of our numerical model for simulating ship solidbody motion in a given environment. In this model, the fully nonlinear dynamical equations governing the time-varying solid-body ship motion under the forces arising from ship wave interactions are solved with given initial conditions. The net force and moment (torque) on the ship body are directly calculated via integration of the hydrodynamic pressure over the wetted surface and the buoyancy effect from the underwater volume of the actual ship hull with a hybrid finite-difference/finite-element method. Neither empirical nor free parametrization is introduced in this model, i.e. no a priori experimental data are needed for modelling. This model is benchmarked with many experiments of various ship hulls for heave, roll and pitch motion. In addition to the benchmark cases, numerical experiments are also carried out for strongly nonlinear ship motion with a fixed heading. These new cases demonstrate clearly the importance of nonlinearities in ship motion modelling.

  5. Structural analysis of a ship on global aspect using ANSYS

    Science.gov (United States)

    Rahman, M. Muzibur; Kamol, Rajia Sultana; Islam, Reyana

    2017-12-01

    Ship is a complex geometry which undergoes a combination of loadings such as hydrostatic, hydrodynamic, wind, wave etc. at sea and thus adequate strength in a ship has always been one of the most challenging tasks for the ship designers. International Maritime Organization (IMO) and classification societies are providing the standards to ensure the adequacy of strength for the ship against all demands throughout its service life. Thus, structural analysis is needed to assess the overall strength of hull, and the means in this regard are based on finite element method which may be applied either local or global aspect of the ship. This paper is an attempt to carry out the structural analysis of a ship in global aspect using ANSYS software to locate the most stress concentration and deformed area, which will have ultimate effect on fatigue fracture.

  6. Modelling of the Internal Mechanics in Ship Collisions

    DEFF Research Database (Denmark)

    Paik, Jeom Kee; Pedersen, Preben Terndrup

    1996-01-01

    A method for analysis of the structural damage due to ship collisions is developed. The method is based on the idealized structural unit method (ISUM). Longitudinal/transverse webs which connect the outer and the inner hulls are modelled by rectangular plate units. The responses are determined...... on the stiffness and the strength is considered as well. In order to include the coupling effects between local and global failure of the structure, the usual non-linear finite-element technique is applied. In order to deal with the gap and contact conditions between the striking and the struck ships, gap......-skin plated structures in collision/grounding situations with the present solutions. As an illustrative example the procedure has been used for analyses of a side collision of a double-hull tanker. Several factors affecting ship collision response, namely the collision speed and the scantlings/ arrangements...

  7. Measurement of flows around modern commercial ship models

    Science.gov (United States)

    Kim, W. J.; Van, S. H.; Kim, D. H.

    To document the details of flow characteristics around modern commercial ships, global force, wave pattern, and local mean velocity components were measured in the towing tank. Three modern commercial hull models of a container ship (KRISO container ship = KCS) and of two very large crude-oil carriers (VLCCs) with the same forebody and slightly different afterbody (KVLCC and KVLCC2) having bow and stern bulbs were selected for the test. Uncertainty analysis was performed for the measured data using the procedure recommended by the ITTC. Obtained experimental data will provide a good opportunity to explore integrated flow phenomena around practical hull forms of today. Those can be also used as the validation data for the computational fluid dynamics (CFD) code of both inviscid and viscous flow calculations.

  8. Measurement of flows around modern commercial ship models

    Energy Technology Data Exchange (ETDEWEB)

    Kim, W J; Van, S H; Kim, D H [Korea Research Inst. of Ships and Ocean Engineering, KORDI, Taejon (Korea)

    2001-11-01

    To document the details of flow characteristics around modern commercial ships, global force, wave pattern, and local mean velocity components were measured in the towing tank. Three modern commercial hull models of a container ship (KRISO container ship = KCS) and of two very large crude-oil carriers (VLCCs) with the same forebody and slightly different afterbody (KVLCC and KVLCC2) having bow and stern bulbs were selected for the test. Uncertainty analysis was performed for the measured data using the procedure recommended by the ITTC. Obtained experimental data will provide a good opportunity to explore integrated flow phenomena around practical hull forms of today. Those can be also used as the validation data for the computational fluid dynamics (CFD) code of both inviscid and viscous flow calculations. (orig.)

  9. Hull's Diploma in Teaching of Adults

    Science.gov (United States)

    Styler, W. E.

    1971-01-01

    A diploma in the Teaching of Adults for part-time students was introduced in the University of Hull in 1966 as a fully recognized university diploma. Article discusses the three major parts of the course, examinations, and requirements. (RB)

  10. Simple analytical relations for ship bow waves

    Science.gov (United States)

    Noblesse, Francis; Delhommeau, G.?Rard; Guilbaud, Michel; Hendrix, Dane; Yang, Chi

    Simple analytical relations for the bow wave generated by a ship in steady motion are given. Specifically, simple expressions that define the height of a ship bow wave, the distance between the ship stem and the crest of the bow wave, the rise of water at the stem, and the bow wave profile, explicitly and without calculations, in terms of the ship speed, draught, and waterline entrance angle, are given. Another result is a simple criterion that predicts, also directly and without calculations, when a ship in steady motion cannot generate a steady bow wave. This unsteady-flow criterion predicts that a ship with a sufficiently fine waterline, specifically with waterline entrance angle 2, may generate a steady bow wave at any speed. However, a ship with a fuller waterline (25E) can only generate a steady bow wave if the ship speed is higher than a critical speed, defined in terms of αE by a simple relation. No alternative criterion for predicting when a ship in steady motion does not generate a steady bow wave appears to exist. A simple expression for the height of an unsteady ship bow wave is also given. In spite of their remarkable simplicity, the relations for ship bow waves obtained in the study (using only rudimentary physical and mathematical considerations) are consistent with experimental measurements for a number of hull forms having non-bulbous wedge-shaped bows with small flare angle, and with the authors' measurements and observations for a rectangular flat plate towed at a yaw angle.

  11. Applying Multi-Class Support Vector Machines for performance assessment of shipping operations: The case of tanker vessels

    DEFF Research Database (Denmark)

    Pagoropoulos, Aris; Møller, Anders H.; McAloone, Tim C.

    2017-01-01

    of feature selection algorithms. Afterwards, a model based on Multi- Class Support Vector Machines (SVM) was constructed and the efficacy of the approach is shown through the application of a test set. The results demonstrate the importance and benefits of machine learning algorithms in driving energy....... Identifying the potential of behavioural savings can be challenging, due to the inherent difficulty in analysing the data and operationalizing energy efficiency within the dynamic operating environment of the vessels. This article proposes a supervised learning model for identifying the presence of energy...

  12. Morphing hull implementation for unmanned underwater vehicles

    Science.gov (United States)

    Miller, Timothy F.; Gandhi, Farhan; Rufino, Russell J.

    2013-11-01

    There has been much interest and work in the area of morphing aircraft since the 1980s. Morphing could also potentially benefit unmanned underwater vehicles (UUVs). The current paper envisions a UUV with an interior pressure hull and a variable diameter outer flexible hull with fuel stored in the annulus between, and presents a mechanism to realize diameter change of the outer hull. The outer hull diameter of UUVs designed for very long endurance/range could be progressively reduced as fuel was consumed, thereby reducing drag and further increasing endurance and range capability. Diameter morphing could also be advantageous for compact storage of UUVs. A prototype is fabricated to represent an axial section of such a morphing diameter UUV. Diameter change is achieved using eight morphing trusses arranged equidistant around the circumference of the representative interior rigid hull. Each morphing truss has a lower rail (attached to the rigid hull) and an upper rail with V-linkages between, at either ends of the rail. Horizontal motion of the feet of the V-linkages (sliding in the lower rail) results in vertical motion of the upper rail which in turn produces diameter change of the outer hull. For the prototype built and tested, a 63% increase in outer diameter from 12.75″ to 20.75″ was achieved. The introduction of a stretched latex representative flexible skin around the outer rails increased actuation force requirement and led to a propensity for the wheel-in-track sliders in the morphing truss to bind. It is anticipated that this could be overcome with higher precision manufacturing. In addition to symmetric actuation of the morphing trusses resulting in diameter change, the paper also shows that with asymmetric actuation the hull cross-section shape can be changed (for example, from a circular section for underwater operation to a V-section for surface operations).

  13. Morphing hull implementation for unmanned underwater vehicles

    International Nuclear Information System (INIS)

    Miller, Timothy F; Gandhi, Farhan; Rufino, Russell J

    2013-01-01

    There has been much interest and work in the area of morphing aircraft since the 1980s. Morphing could also potentially benefit unmanned underwater vehicles (UUVs). The current paper envisions a UUV with an interior pressure hull and a variable diameter outer flexible hull with fuel stored in the annulus between, and presents a mechanism to realize diameter change of the outer hull. The outer hull diameter of UUVs designed for very long endurance/range could be progressively reduced as fuel was consumed, thereby reducing drag and further increasing endurance and range capability. Diameter morphing could also be advantageous for compact storage of UUVs. A prototype is fabricated to represent an axial section of such a morphing diameter UUV. Diameter change is achieved using eight morphing trusses arranged equidistant around the circumference of the representative interior rigid hull. Each morphing truss has a lower rail (attached to the rigid hull) and an upper rail with V-linkages between, at either ends of the rail. Horizontal motion of the feet of the V-linkages (sliding in the lower rail) results in vertical motion of the upper rail which in turn produces diameter change of the outer hull. For the prototype built and tested, a 63% increase in outer diameter from 12.75″ to 20.75″ was achieved. The introduction of a stretched latex representative flexible skin around the outer rails increased actuation force requirement and led to a propensity for the wheel-in-track sliders in the morphing truss to bind. It is anticipated that this could be overcome with higher precision manufacturing. In addition to symmetric actuation of the morphing trusses resulting in diameter change, the paper also shows that with asymmetric actuation the hull cross-section shape can be changed (for example, from a circular section for underwater operation to a V-section for surface operations). (paper)

  14. Wave-induced Hydroelastic response of fast monohull ships

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher

    1996-01-01

    High-speed ships are weight sensitive structures and high strength steel, aluminium or composites are preferred building materials. it is characteristic for these materials that they result in larger hull flexibility than more conventional materials. Therefore, for large fast ships the lowest...... of a quadratic strip theory formulated in the frequency domain. The springing response is thereby excited partly be resonance and partly by non-linear excitation. Special emphasis is given to the influence of springing on fatigue damage as the extreme responses even for very flexible ships are quite insensitive...

  15. Annual report of Japan Nuclear Ship Development Agency

    International Nuclear Information System (INIS)

    1978-01-01

    Works performed in fiscal 1977 concerning the nuclear ship 'Mutsu' are reported: safety inspection and shielding repair of the Mutsu; maintenance of the Mutsu and its port facilities; permissions by law; P.R. etc. on its prospective repair port; ship crew training; and, organization etc. Safety inspection of the Mutsu was carried out on its both hardware and software. For repair, a final basic design was started. Without ship operation, the Mutsu's hull, reactor plant, etc. and port facilities were subjected to maintenance works. P.R. works on its repair port concentrated on understanding of the local people. (Mori, K.)

  16. Study on estimating fluid force acting on a hull during maneuvering movement; Soju undoji no sentai ni sayosuru ryutairyoku no suitei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yukawa, K; Kijima, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1997-10-01

    With types of general cargo vessel and VLCC vessel as the object of discussion, a method was discussed to estimate fluid force acting theoretically on a hull during maneuvering movement, taking frame line shape into consideration. A vortex model was improved by giving consideration of time-based decay on intensity of discrete vortex lines based on the Rankine vortex. Modeling of flow fields around a hull was attempted to deal with movements in which width and draft are small as compared with the ship length, and turning angle speed and deviation angle are small. It was assumed that the ship speed is slow and effects of waves can be disregarded. Specular images of the hull were taken with regard to free surface, and handled as a double body model. Speed potential to express flow fields around a hull is required to satisfy the following five boundary conditions of Laplace, substance surface, free vortex layers, infinity and exfoliation. The potential may be handled as a two-dimensional problem in a field near the hull by using assumption of a slender and long body and conformal mapping. It was found possible to estimate hull fluid force with relatively good accuracy. Fine linear coefficients derived from the estimation were used to have performed highly accurate determination on course stabilization. 5 refs., 6 figs., 2 tabs.

  17. Automatic Generation of the Planning Tunnel High Speed Craft Hull Form

    Institute of Scientific and Technical Information of China (English)

    Morteza Ghassabzadeh; Hassan Ghassemi

    2012-01-01

    The creation of geometric model of a ship to determine the characteristics of hydrostatic and hydrodynamic,and also for structural design and equipments arrangement are so important in the ship design process.Planning tunnel high speed craft is one of the crafts in which,achievement to their top speed is more important.These crafts with the use of tunnel have the aero-hydrodynamics properties to diminish the resistance,good sea-keeping behavior,reduce slamming and avoid porpoising.Because of the existence of the tunnel,the hull form generation of these crafts is more complex and difficult.In this paper,it has attempted to provide a method based on geometry creation guidelines and with an entry of the least control and hull form adjustment parameters,to generate automatically the hull form of planning tunnel craft.At first,the equations of mathematical model are described and subsequent,three different models generated based on present method are compared and analyzed.Obviously,the generated model has more application in the early stages of design.

  18. Fluid dynamic interface between hull and hydrofoil; Sentai to suichuyoku no ryutai rikigakuteki kansho ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Kataoka, K; Ando, J; Nakatake, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1996-04-10

    For the high-speed ship with hydrofoil, it is important to grasp the mutual interference between its hydrofoil and hull. In this study, effects of the state of hydrofoils and velocity on the hull were fluid-dynamically investigated through the numerical calculation by means of Rankine source method using a Wigley model with two hydrofoils. Before considering the model with hydrofoils, the attitude change of a hull without hydrofoils during traveling in high-speed was examined. For the high-speed ship, various measuring systems have been conceived due to the large change in its attitude. The Wigley model has been used for the numerical calculation when considering the attitude change in the medium- and low-speed regions. In this study, resistance tests without constraining the sinkage and trim were conducted using a Wigley model in the high-speed region around Fn=1.0, which have not been usually conducted. The attitude changes were compared with the numerical calculation results by the Rankine source method. The wave making resistance and attitude change of the Wigley model with hydrofoils were also calculated. 12 refs., 10 figs.

  19. PIXE Analysis of Metal Hull Bolts From HMB DeBraak

    International Nuclear Information System (INIS)

    Correll, Francis D.; Cole, Lord K.; Slater, Charles J.; Vanhoy, Jeffrey R.; Fithian, Charles H.

    2009-01-01

    HMB DeBraak was a 16-gun British brig-sloop that sank in a squall on May 25, 1798 off Cape Henlopen, Delaware. Silt covered the wooden hull shortly after it sank, preserving it until DeBraak was raised in 1986. The items recovered from the ship include metal bolts that held the hull together. We used PIXE to measure the compositions of 45 of the bolts and found that they are nearly pure copper (98.3% on average), with most also containing small amounts of iron (0.87%), nickel (0.039%), arsenic (0.43%), silver (0.089%), lead (0.18%), and bismuth (0.12%). A few contain a little indium, tin, or antimony, but none contain zinc above the quantization level. The compositions are similar to those reported for 18th-century English copper, but different from several copper alloys also used to make hull bolts. We conclude that, when DeBraak was last fitted out in 1795-1797, the Royal Navy was still using bolts similar to William Forbes's mechanically hardened pure copper bolts. Forbes's process represents the successful innovation and application of new technology in Royal Navy ships during the wars of the late 18th century.

  20. PIXE Analysis of Metal Hull Bolts From HMB DeBraak

    Science.gov (United States)

    Correll, Francis D.; Cole, Lord K.; Slater, Charles J.; Vanhoy, Jeffrey R.; Fithian, Charles H.

    2009-03-01

    HMB DeBraak was a 16-gun British brig-sloop that sank in a squall on May 25, 1798 off Cape Henlopen, Delaware. Silt covered the wooden hull shortly after it sank, preserving it until DeBraak was raised in 1986. The items recovered from the ship include metal bolts that held the hull together. We used PIXE to measure the compositions of 45 of the bolts and found that they are nearly pure copper (98.3% on average), with most also containing small amounts of iron (0.87%), nickel (0.039%), arsenic (0.43%), silver (0.089%), lead (0.18%), and bismuth (0.12%). A few contain a little indium, tin, or antimony, but none contain zinc above the quantization level. The compositions are similar to those reported for 18th-century English copper, but different from several copper alloys also used to make hull bolts. We conclude that, when DeBraak was last fitted out in 1795-1797, the Royal Navy was still using bolts similar to William Forbes's mechanically hardened pure copper bolts. Forbes's process represents the successful innovation and application of new technology in Royal Navy ships during the wars of the late 18th century.

  1. Experiments on multi-nucleon transfer reactions with the systems {sup 58,64}Ni+{sup 207}Pb at SHIP

    Energy Technology Data Exchange (ETDEWEB)

    Fernandovich Comas Lijachev, Victor

    2012-07-01

    This work presents experimental results on multi-nucleon transfer reactions in the collision systems {sup 58}Ni+{sup 207}Pb and {sup 64}Ni+{sup 207}Pb which were measured at the velocity filter SHIP at GSI. The reactions were performed at beam energies below and up to 10% above the Coulomb barrier. The work was motivated by theoretical predictions to apply multi-nucleon transfer reactions in heavy systems to synthesize new neutron-rich isotopes in the region of superheavy nuclei with Z>100 and in the region of the closed neutron shell N=126. The expected cross-sections for the production of these nuclei in transfer reactions are small and reach typically nanobarn and below. Therefore, efficient separation techniques have to be applied and the detection system must allow for the identification of single nuclei. A dedicated experimental setup to study such rare transfer products does not exist presently. But already existing facilities which are used for the synthesis of superheavy fusion products meet the requirements for the detection of rare reaction products. In this context, the velocity filter SHIP offers the possibility to separate heavy target-like transfer products from projectiles and projectile-like reaction products before they reach the detection system where the particles are identified by their alpha-decay properties. At SHIP, a cross-section limit of 10 pb can be reached at usual beam intensities. In the present work on collisions of {sup 58,64}Ni+{sup 207}Pb the influence of the projectile neutron number on the cross-sections, isotopic distributions and excitation energies of the transfer products was studied. Especially with the more neutron-rich {sup 64}Ni projectiles a transfer of up to seven protons and eight neutrons to the target nucleus was observed. The largest cross-sections for the most neutron-rich isotopes were reached at the beam energies around the Coulomb barrier. The transfer was accompanied by the full dissipation of the available

  2. Collision simulations of an exclusive ship of spent nuclear fuels

    International Nuclear Information System (INIS)

    Kitamura, Ou; Endo, Hisayoshi

    2000-01-01

    Exclusive ships for sea transport of irradiated nuclear fuels operating in Japanese territorial waters are required to be built with the special hull structure against collision. To comply with the official notice 'KAISA No. 520' issued by the Ministry of Transport, the side structure of any such exclusive ship must be designed to secure the specified energy absorption capability based on Minorsky's ship collision model. The Shipbuilding Research Association of Japan (JSRA) has studied the safety in sea transport of nuclear fuels intermittently for these several decades. Recently, the adoption of finite element method has made detailed collision analyses practicable. Since 1998, the regulation research panel No. 46 of JSRA has carried out a series of finite element collision simulations in order to estimate the realistic damage to a typical exclusive ship of spent nuclear fuels. The expected structural responses, global motions and energy absorption capabilities of both colliding and struck ships during collision were investigated. The results of the investigations have shown that the ship is very likely to withstand the collision even with one of the world's largest ship. This is due mainly to her hull structure specially strengthened beyond the crushing strength of the colliding bow structures. (author)

  3. Hull Surface Information Retrieval and Optimization of High Speed Planing Craft

    International Nuclear Information System (INIS)

    Ayob, A F; Wan Nik, W B; Ray, T; Smith, W F

    2012-01-01

    Traditional approach on ship design involve the use of a method which takes a form that was earlier called the 'general design diagram' and is now known as the 'design spiral' – an iterative ship design process that allows for an increase in complexity and precision across the design cycle. Several advancements have been made towards the design spiral, however inefficient for handling complex simultaneous design changes, especially when later variable changes affect the ship's performance characteristics evaluated in earlier stages. Reviewed in this paper are several advancements in high speed planing craft design in preliminary design stage. An optimization framework for high speed planing craft is discussed which consist of surface information retrieval module, a suite of state-of-the-art optimization algorithms and standard naval architectural performance estimation tools. A summary of the implementation of the proposed hull surface information retrieval and several case studies are presented to demonstrate the capabilities of the framework.

  4. Coefficients of Propeller-hull Interaction in Propulsion System of Inland Waterway Vessels with Stern Tunnels

    Directory of Open Access Journals (Sweden)

    Jan Kulczyk

    2014-09-01

    Full Text Available Propeller-hull interaction coefficients - the wake fraction and the thrust deduction factor - play significant role in design of propulsion system of a ship. In the case of inland waterway vessels the reliable method of predicting these coefficients in early design stage is missing. Based on the outcomes from model tests and from numerical computations the present authors show that it is difficult to determine uniquely the trends in change of wake fraction and thrust deduction factor resulting from the changes of hull form or operating conditions. Nowadays the resistance and propulsion model tests of inland waterway vessels are carried out rarely because of relatively high costs. On the other hand, the degree of development of computational methods enables’ to estimate the reliable values o interaction coefficients. The computations referred to in the present paper were carried out using the authors’ own software HPSDKS and the commercial software Ansys Fluent.

  5. A Novel Approach to Turbulence Stimulation for Ship-Model Testing

    Science.gov (United States)

    2010-05-11

    a given hull form. As van Manen and van Oossanen note, ship resistance is related to “the proportions and shape… of the hull, the size and type of...propulsion plant to provide motive power, and the device or system to transform the power into effective thrust” ( van Manen and van Oossanen, 1988...what is known as the Ship-Model Tester’s Dilemma, which van Manen and van Oossanen define as “the conditions of mechanical similitude for both friction

  6. Region-of-interest volumetric visual hull refinement

    KAUST Repository

    Knoblauch, Daniel; Kuester, Falko

    2010-01-01

    This paper introduces a region-of-interest visual hull refinement technique, based on flexible voxel grids for volumetric visual hull reconstructions. Region-of-interest refinement is based on a multipass process, beginning with a focussed visual

  7. Management of cladding hulls and fuel hardware

    International Nuclear Information System (INIS)

    1985-01-01

    The reprocessing of spent fuel from power reactors based on chop-leach technology produces a solid waste product of cladding hulls and other metallic residues. This report describes the current situation in the management of fuel cladding hulls and hardware. Information is presented on the material composition of such waste together with the heating effects due to neutron-induced activation products and fuel contamination. As no country has established a final disposal route and the corresponding repository, this report also discusses possible disposal routes and various disposal options under consideration at present

  8. Obtaining high purity silica from rice hulls

    Directory of Open Access Journals (Sweden)

    José da Silva Júnior

    2010-01-01

    Full Text Available Many routes for extracting silica from rice hulls are based on direct calcining. These methods, though, often produce silica contaminated with inorganic impurities. This work presents the study of a strategy for obtaining silica from rice hulls with a purity level adequate for applications in electronics. The technique is based on two leaching steps, using respectively aqua regia and Piranha solutions, which extract the organic matrix and inorganic impurities. The material was characterized by Fourier-transform infrared spectroscopy (FTIR, powder x-ray diffraction (XRD, x-ray fluorescence (XRF, scanning electron microscopy (SEM, particle size analysis by laser diffraction (LPSA and thermal analysis.

  9. Numerical simulation of viscous flow and hydrodynamic noise in surface ship

    Directory of Open Access Journals (Sweden)

    YU Han

    2017-12-01

    Full Text Available [Objectives] The problem of noise caused by an unsteady flow field around a surface ship is a difficulty facing the stealth design of ship hulls, in which the existence of the free surface makes it different from submarine hydrodynamic noise calculation. To solve this problem,[Methods] the Volume of Fluid(VOF method and SST k-ω turbulence model are combined to simulate the unsteady flow field of the hull, and the free surface is given an air acoustic impedance to simulate the absorption boundary. The pulsating pressure of the hull surface is used as the source of the noise, and the underwater radiation noise of the surface ship is calculated with the acoustic finite element method.[Results] The results show high agreement with the experimental results and previous simulation results. The noise sources are mainly concentrated at the bow of the hull.[Conclusions] The results show that this calculation method can accurately simulate the flow field and sound field of a surface ship, and it can provides valuable reference for the acoustic stealth design of surface ships.

  10. Ship's barbers

    OpenAIRE

    Unknown

    2003-01-01

    Showing two sailors having their hair cut (? one is possibly being shaved) on board ship. Three other sailors can be seen standing on the right-hand side of the photograph. The photograph is from an album inscribed 'H.M.S. Lancaster; Mediterranean Photographic Album: Diary of Events and Important Places Visited during the Commission 1910-1912' on the cover. This album was the property of Sydney Harold Liddle.

  11. Effects of hull form parameters on seakeeping for YTU gulet series with cruiser stern

    Directory of Open Access Journals (Sweden)

    Cakici Ferdi

    2014-09-01

    Full Text Available This study aims to identify the relations between seakeeping characteristics and hull form parameters for YTU Gulet series with cruiser stern. Seakeeping analyses are carried out by means of a computer software which is based on the strip theory and statistical short term response prediction method. Multiple regression analysis is used for numerical assessment through a computer software. RMS heave-pitch motions and absolute vertical accelerations on passenger saloon for Sea State 3 at head waves are investigated for this purpose. It is well known that while ship weight and the ratios of main dimensions are the primary factors on ship motions, other hull form parameters (CP, CWP, CVP, etc. are the secondary factors. In this study, to have an idea of geometric properties on ship motions of gulets three different regression models are developed. The obtained outcomes provide practical predictions of seakeeping behavior of gulets with a high level of accuracy that would be useful during the concept design stage

  12. Effects of Common Structural Rules on hull-girder reliability of an Aframax oil tanker

    International Nuclear Information System (INIS)

    Parunov, Josko; Guedes Soares, C.

    2008-01-01

    This paper aims at quantifying the changes in notional reliability levels that result from redesigning an existing Aframax tanker to comply with the Common Structural Rules (CSR) for double-hull oil tankers. The probability of structural failure is calculated using the first-order reliability method. The evaluation of the wave-induced load effects that occur during long-term operation of the ship in the seaway is carried out in accordance with the International Association of Classification Societies (IACS)-recommended procedure, while transfer functions are calculated using the sink-source 3D linear method. The still-water loads are defined on the basis of a statistical analysis of loading conditions from the loading manual. The ultimate collapse bending moment of the midship cross section, which is used as the basis for the reliability formulation, is evaluated by progressive collapse analysis and by a single-step procedure according to CSR. The reliability assessment is performed for 'as-built' and 'corroded' states of the existing ship and a reinforced ship complying with CSR. It is shown that the hull-girder failure probability of an Aframax tanker is reduced several times due to the reinforcements according to CSR. Sensitivity analysis and a parametric study are performed to investigate the variability of results with the change of parameters of pertinent random variables within their plausible ranges. Finally, differences between load combination approaches by Ferry-Borges and Castanheta method and Turkstra's rule are investigated

  13. 33 CFR 181.25 - Hull identification number format.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Hull identification number format... (CONTINUED) BOATING SAFETY MANUFACTURER REQUIREMENTS Identification of Boats § 181.25 Hull identification number format. Each of the hull identification numbers required by § 181.23 must consist of twelve...

  14. 33 CFR 181.29 - Hull identification number display.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Hull identification number... SECURITY (CONTINUED) BOATING SAFETY MANUFACTURER REQUIREMENTS Identification of Boats § 181.29 Hull identification number display. Two identical hull identification numbers are required to be displayed on each...

  15. 33 CFR 181.23 - Hull identification numbers required.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Hull identification numbers... SECURITY (CONTINUED) BOATING SAFETY MANUFACTURER REQUIREMENTS Identification of Boats § 181.23 Hull... identify each boat produced or imported with two hull identification numbers that meet the requirements of...

  16. Flow measurement around a model ship with propeller and rudder

    Energy Technology Data Exchange (ETDEWEB)

    Van, S H; Yoon, H S; Lee, Y Y; Park, I R [Korea Research Institute of Ships and Ocean Engineering, KORDI, Marine Transportation Systems Laboratory, Daejeon (Korea); Kim, W J [Mokpo National University, Department of Naval Architecture and Marine Engineering, Jeonnam (Korea)

    2006-04-15

    For the design of hull forms with better resistance and propulsive performance, it is essential to understand flow characteristics, such as wave and wake development, around a ship. Experimental data detailing the local flow characteristics are invaluable for the validation of the physical and numerical modeling of computational fluid dynamics (CFD) codes, which are recently gaining attention as efficient tools for hull form evaluation. This paper describes velocity and wave profiles measured in the towing tank for the KRISO 138,000 m{sup 3} LNG carrier model with propeller and rudder. The effects of propeller and rudder on the wake and wave profiles in the stern region are clearly identified. The results contained in this paper can provide an opportunity to explore integrated flow phenomena around a model ship in the self-propelled condition, and can be added to the International Towing Tank Conference benchmark data for CFD validation as the previous KCS and KVLCC cases. (orig.)

  17. Flow measurement around a model ship with propeller and rudder

    Science.gov (United States)

    van, S. H.; Kim, W. J.; Yoon, H. S.; Lee, Y. Y.; Park, I. R.

    2006-04-01

    For the design of hull forms with better resistance and propulsive performance, it is essential to understand flow characteristics, such as wave and wake development, around a ship. Experimental data detailing the local flow characteristics are invaluable for the validation of the physical and numerical modeling of computational fluid dynamics (CFD) codes, which are recently gaining attention as efficient tools for hull form evaluation. This paper describes velocity and wave profiles measured in the towing tank for the KRISO 138,000 m3 LNG carrier model with propeller and rudder. The effects of propeller and rudder on the wake and wave profiles in the stern region are clearly identified. The results contained in this paper can provide an opportunity to explore integrated flow phenomena around a model ship in the self-propelled condition, and can be added to the International Towing Tank Conference benchmark data for CFD validation as the previous KCS and KVLCC cases.

  18. Rhythmical Alchemy: Village Drumming with Arthur Hull.

    Science.gov (United States)

    Hillerson, Gary R.; Hull, Arthur

    As a step toward writing a master's thesis in psychology, the connection between rhythm circles and psychotherapeutic process was explored. Arthur Hull, who experienced and preached about the healing power of rhythm for many years, was interviewed. This article recorded the interview between Arthur and the researcher. The interviewer learned that…

  19. "Keisri hull" on viimast korda laval

    Index Scriptorium Estoniae

    2010-01-01

    Neli hooaega Ugala repertuaaris olnud Jaan Krossi romaani põhjal lavastatud draama "Keisri hull" etendub viimast korda 10. veebruaril. Viimane etendus on pühendatud Jaan Krossi 90. sünniaastapäevale, mis on 19. veebruaril. Lavastajad Peeter Tammearu ja Jaak Allik. Peaosas Peeter Tammearu

  20. Convex Hull Aided Registration Method (CHARM).

    Science.gov (United States)

    Fan, Jingfan; Yang, Jian; Zhao, Yitian; Ai, Danni; Liu, Yonghuai; Wang, Ge; Wang, Yongtian

    2017-09-01

    Non-rigid registration finds many applications such as photogrammetry, motion tracking, model retrieval, and object recognition. In this paper we propose a novel convex hull aided registration method (CHARM) to match two point sets subject to a non-rigid transformation. First, two convex hulls are extracted from the source and target respectively. Then, all points of the point sets are projected onto the reference plane through each triangular facet of the hulls. From these projections, invariant features are extracted and matched optimally. The matched feature point pairs are mapped back onto the triangular facets of the convex hulls to remove outliers that are outside any relevant triangular facet. The rigid transformation from the source to the target is robustly estimated by the random sample consensus (RANSAC) scheme through minimizing the distance between the matched feature point pairs. Finally, these feature points are utilized as the control points to achieve non-rigid deformation in the form of thin-plate spline of the entire source point set towards the target one. The experimental results based on both synthetic and real data show that the proposed algorithm outperforms several state-of-the-art ones with respect to sampling, rotational angle, and data noise. In addition, the proposed CHARM algorithm also shows higher computational efficiency compared to these methods.

  1. Estimation of penetration depth of fission products in cladding Hull

    International Nuclear Information System (INIS)

    Kim, Hee Moon; Jung, Yang Hong; Yoo, Byong Ok; Choo, Yong Sun; Hong, Kwon Pyo

    2005-01-01

    A disposal and a reprocessing for spent fuel rod with high burnup need de-cladding procedure. Pellet in this rod has been separated from a cladding hull to reduce a radioactivity of hull by chemical and mechanical methods. But fission products and actinides(U,Pu) still remain inside of cladding hull by chemical bonding and fission spike, which is called as 'contamination'. More specific removal of this contamination would have been considered. In this study, the sorts of fission products and penetration depth in hull were observed by EPMA test. To analyze this behavior, SRIM 2000 code was also used as energies of fission products and an oxide thickness of hull

  2. A Multi-Polarization Study on Ship Detection over X-Band Full-Resolution COSMO SkyMed SAR Data

    Science.gov (United States)

    Migliaccio, Maurizio; Nunziata, Ferdinando; Sorrentio, Antonio; Ferrara, Giuseppe

    2011-03-01

    Ship detection over marine Synthetic Aperture Radar (SAR) images is a key application for global monitoring for environment and security. In this paper, a physically-based filter which exploits a proper combination of GK parameters is conceived to unambiguously observe ships over sea surface in HV-polarized Single Look Complex (SLC) SAR data. Experiments accomplished over a meaningful set of X-band SLC CosmoSkyMed StripMap SAR data confirm the physical soundness of the proposed approach.

  3. Mathematical Ship Modeling for Control Applications

    DEFF Research Database (Denmark)

    Perez, Tristan; Blanke, Mogens

    2002-01-01

    In this report, we review the models for describing the motion of a ship in four degrees of freedom suitable for control applications. We present the hydrodynamic models of two ships: a container and a multi-role naval vessel. The models are based on experimental results in the four degrees...

  4. Comparison of residual strength-grounding damage index diagrams for tankers produced by the ALPS/HULL ISFEM and design formula method

    Directory of Open Access Journals (Sweden)

    Do Kyun Kim

    2013-03-01

    Full Text Available This study compares the Residual ultimate longitudinal strength – grounding Damage index (R-D diagrams produced by two analysis methods: the ALPS/HULL Intelligent Supersize Finite Element Method (ISFEM and the design formula (modified Paik and Mansour method – used to assess the safety of damaged ships. The comparison includes four types of double-hull oil tankers: Panamax, Aframax, Suezmax and VLCC. The R-D diagrams were calculated for a series of 50 grounding scenarios. The diagrams were efficiently sampled using the Latin Hypercube Sampling (LHS technique and comprehensively analysed based on ship size. Finally, the two methods were compared by statistically analysing the differences between their grounding damage indices and ultimate longitudinal strength predictions. The findings provide a useful example of how to apply the ultimate longitudinal strength analysis method to grounded ships.

  5. Motions and Hull-Induced Bridging-Structure Loads for a Small Waterplane Area, Twin-Hulled, Attack Aircraft Carrier in Waves

    National Research Council Canada - National Science Library

    Jones, Harry D; Gerzina, David M

    1973-01-01

    ... small waterplane area, twin-hulled, attack aircraft carrier in waves. Motions of the model were measured, together with the forces and moments induced by the hulls on the cross structure spanning the two hulls...

  6. 9. Anti-vibration Design of a Passenger Ship

    OpenAIRE

    Kazuo, Umezaki; Mikihiro, Kobayashi; Hioshi Kohkawa, Kohkawa; Hiroyuki, Mizuno; Shin-ichi, Nishimura; Takayuki, Okayasu; Kazuhisa, Yanagi; Mitsubishi Heavy Industries. Ltd; Mitsubishi Heavy Industries, Ltd. Kobe Shipyard and Machinery Works; Mitsubishi Heavy Industries, Ltd. Kobe Shipyard and Machinery Works; Mitsubishi Heavy Industries, Ltd. Kobe Shipyard and Machinery Works; Mitsubishi Heavy Industries. Ltd; Mitsubishi Heavy Industries, Ltd. Kobe Shipyard and Machinery Works; Mitsubishi Heavy Industries, Ltd. Nagasaki Research and Development Center

    1992-01-01

    One of the most difficult tasks in designing a passenger ship is to make it vibration free while keeping the hull structure very light for stability reason. In order to accomplish this for the 23,000 GT cruise ship the particulars of which are shown in Table l, special attention was paid to the alignment of structures during layout design, and analyses and experiments of vibration were carried out through every stage of design and construction. This paper describes outlines of these tasks and...

  7. Wind Tunnel Assessment of Ship Manoeuvrability using a PMM Technique

    DEFF Research Database (Denmark)

    Agdrup, Kristian; Jensen, Andreas G.; Aage, Christian

    1999-01-01

    Tests have been performed at the Danish Maritime Institute (DMI) to investigate the applicability of a new wind tunnel Planar Motion Mechanism (PMM) for the determination of hydrodynamic coefficients of ships. The method has been tested on a tanker with known towing tank data. The wind tunnel model...... data giving reasonable results. The dependency of amplitude and frequency is evaluated, and sources of inaccuracy are discussed. It is concluded that the wind tunnel method is a promising method to achieve a fast and cost-effective estimate of the hydrodynamic coefficients of a ship hull...

  8. Modelling Analysis of Echo Signature and Target Strength of a Realistically Modelled Ship Wake for a Generic Forward Looking Active Sonar

    NARCIS (Netherlands)

    Schippers, P.

    2009-01-01

    The acoustic modelling in TNO’s ALMOST (=Acoustic Loss Model for Operational Studies and Tasks) uses a bubble migration model as realistic input for wake modelling. The modelled bubble cloud represents the actual ship wake. Ship hull, propeller and bow wave are the main generators of bubbles in the

  9. DECONTAMINATION OF ZIRCALOY SPENT FUEL CLADDING HULLS

    International Nuclear Information System (INIS)

    Rudisill, T; John Mickalonis, J

    2006-01-01

    The reprocessing of commercial spent nuclear fuel (SNF) generates a Zircaloy cladding hull waste which requires disposal as a high level waste in the geologic repository. The hulls are primarily contaminated with fission products and actinides from the fuel. During fuel irradiation, these contaminants are deposited in a thin layer of zirconium oxide (ZrO 2 ) which forms on the cladding surface at the elevated temperatures present in a nuclear reactor. Therefore, if the hulls are treated to remove the ZrO 2 layer, a majority of the contamination will be removed and the hulls could potentially meet acceptance criteria for disposal as a low level waste (LLW). Discard of the hulls as a LLW would result in significant savings due to the high costs associated with geologic disposal. To assess the feasibility of decontaminating spent fuel cladding hulls, two treatment processes developed for dissolving fuels containing zirconium (Zr) metal or alloys were evaluated. Small-scale dissolution experiments were performed using the ZIRFLEX process which employs a boiling ammonium fluoride (NH 4 F)/ammonium nitrate (NH 4 NO 3 ) solution to dissolve Zr or Zircaloy cladding and a hydrofluoric acid (HF) process developed for complete dissolution of Zr-containing fuels. The feasibility experiments were performed using Zircaloy-4 metal coupons which were electrochemically oxidized to produce a thin ZrO 2 layer on the surface. Once the oxide layer was in place, the ease of removing the layer using methods based on the two processes was evaluated. The ZIRFLEX and HF dissolution processes were both successful in removing a 0.2 mm (thick) oxide layer from Zircaloy-4 coupons. Although the ZIRFLEX process was effective in removing the oxide layer, two potential shortcomings were identified. The formation of ammonium hexafluorozirconate ((NH 4 ) 2 ZrF 6 ) on the metal surface prior to dissolution in the bulk solution could hinder the decontamination process by obstructing the removal of

  10. Indications of marine bioinvasion from network theory. An analysis of the global cargo ship network

    NARCIS (Netherlands)

    Kölzsch, A.; Blasius, B.

    2011-01-01

    The transport of huge amounts of small aquatic organisms in the ballast tanks and at the hull of large cargo ships leads to ever increasing rates of marine bioinvasion. In this study, we apply a network theoretic approach to examine the introduction of invasive species into new ports by global

  11. The simplified interaction tool for efficient and accurate underwater shock analysis of naval ships

    NARCIS (Netherlands)

    Aanhold, J.E. van; Trouwborst, W.; Vaders, J.A.A.

    2014-01-01

    In order to satisfy the need for good quality UNDEX response estimates of naval ships, TNO developed the Simplified Interaction Tool (SIT) for underwater shock analysis. The SIT is a module of user routines linked to LS-DYNA, which generates the UNDEX loading on the wet hull of a 3D finite element

  12. European single-hull regulation in force

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, Michael

    2004-07-01

    The European Union (EU)has decided that from 21 October 2003 no single-hull tanker carrying heavy grades of oil will be permitted to enter or leave ports or offshore installations or anchor in areas under the jurisdiction of the EU member states. Some of the provisions of the EU regulation will not be in force until 2010. The article looks back on what has led up to to the current regulations, beginning with the Titanic disaster of 1914.

  13. The Causes of Boat Hull Blisters

    Science.gov (United States)

    1987-05-01

    blistering. The report is divided into the following sections: Introduction; How Blisters Form; the Hull Material; Manufacturing Processes; Water Diffusion...Term Effects of Water Up-Takeo " The much more detailed and highly technical report of thia-Vsrk is entitled "The Causes of Blistering in Boat Building...Chemical Engineering, ably assisted by several graduate students, and was completed in the fall of 1986. The report itself, d List-ribution/_ Availabilit

  14. Topology Model of the Flow around a Submarine Hull Form

    Science.gov (United States)

    2015-12-01

    UNCLASSIFIED Topology Model of the Flow around a Submarine Hull Form S.-K. Lee Maritime Division Defence Science and Technology Group DST-Group–TR...3177 ABSTRACT A topology model constructed from surface-streamer visualisation describes the flow around a generic conventional submarine hull form at...pure yaw angles of 0 ◦, 10 ◦ and 18 ◦. The model is used to develop equations for sway-force and yaw-moment coefficients which relate to the hull - form

  15. Effects of Geometry on the Steady Performance of Planing Hulls

    DEFF Research Database (Denmark)

    Wagner, M. K.; Andersen, Poul

    2003-01-01

    A vortex-lattice method is applied to planing hull forms. The geometry of the jet surfaces next to the wetted hull is estimated on the basis of the hull geometry while its sidewise extent has been found numerically applying a non-linear free-surface pressure condition in the jet region. The method...... is applied to practical hull forms with chines spray rails and with varying deadrise over the length of the boat. The deadrise variation has a large influence on lift and drag. For a design situation, where the total lift and centre of effort is given, the influence on the total drag is less due to change...

  16. Rice Hulls as a Renewable Complex Material Resource

    Directory of Open Access Journals (Sweden)

    Irina Glushankova

    2018-05-01

    Full Text Available As a result of rice grain processing, a big amount of waste (up to 20% is produced. It is mainly rice hulls. The main components of rice hulls are cellulose, lignin and mineral ash. The mineral ash quantity in rice hulls varies from 15 up to 20%, by weight of the rice hulls. The mineral ash consists of amorphous silica (opal-type. Due to the high content of silica in rice hulls, the material burns with difficulty under natural conditions, and it is biodegradably destroyed only with difficulty, when composted. Utilization of rice hulls then becomes an ecological problem due to huge rice production and its continuous growth. At the same time, the annual quantity of silica content in rice hulls is comparable with the quantity of amorphous silica produced as a mineral resource. The issue of manufacturing cellular glass silica construction materials from rice hulls as a renewable resource is discussed in this paper. The utilization technology is based on an amorphous silicon oxide with the use of energy from the combustion of the organic component of rice hulls.

  17. Estimation of gamma dose rate from hulls and shield design for the hull transport cask of Fuel Reprocessing Plant (FRP)

    International Nuclear Information System (INIS)

    Chandrasekaran, S.; Rajagopal, V.; Jose, M.T.; Venkatraman, B.

    2012-01-01

    In Fuel Reprocessing Plant (FRP), un-dissolved clad of fuel pins known as hulls are the major sources of high level solid waste. Safe handling, transport and disposal require the estimation of radioactivity as a consequent of gamma dose rate from hulls in fast reactor fuel reprocessing plant in comparison with thermal reactor fuel. Due to long irradiation time and low cooling of spent fuel, the evolution of activation products 51 Cr, 58 Co, 54 Mn and 59 Fe present as impurities in the fuel clad are the major sources of gamma radiation. Gamma dose rate from hull container with hulls from Fuel Sub Assembly (FSA) and Radial Sub Assembly (RSA) of Fuel Reprocessing Plant (FRP) was estimated in order to design the hull transport cask. Shielding computations were done using point kernel code, IGSHIELD. This paper describes the details of source terms, estimation of dose rate and shielding design of hull transport cask in detail. (author)

  18. Green Shipping Practices of Shipping Firms

    Directory of Open Access Journals (Sweden)

    Young-Tae Chang

    2017-05-01

    Full Text Available The primary objective of this study is to provide an empirical research using structural equation modeling to identify the factors that motivate shipping firms to adopt green shipping practices (GSP. Furthermore, it also examines if adopting GSP can enhance the shipping firms’ environmental and productivity performance. The findings show that shipping firms are motivated to adopt GSP mostly by industrial norms set by institutionalized associations. They are also motivated by customers’ demand for environmental friendliness and their own strategy to make good image. Unlike our expectation, government regulations and international environmental laws are not significant in influencing shipping firms to adopt GSP. Moreover, adoption of green shipping practices can improve the environmental and productivity performance of the shipping firms.

  19. Technical note: In situ ruminal starch disappearance kinetics of hull-less barley, hulled barley, and corn grains.

    Science.gov (United States)

    Ferreira, G; Yang, Y; Teets, C L; Brooks, W S; Griffey, C A

    2018-07-01

    The objective of this study was to compare ruminal starch disappearance rates of hull-less barley, hulled barley, and corn grains. Five different genotypes were used for each of the 2 barley types. In addition, each of these genotypes was grown in 2 different locations and years, resulting 10 independent barley samples for each of the 2 barley grain types. Five different genotypes of corn grain were obtained from a commercial seed company. After being ground to pass through a 4-mm screen of a cutter mill, 3.6 g of each grain was placed into a porous bag, which was then incubated in the rumen of 2 ruminally cannulated cows for 0, 4, 8, 12, 24, and 48 h. Corn grains had greater instant ruminal starch disappearances than barley grains (22.4 and 8.2%, respectively). Instant ruminal starch disappearances did not differ between hulled and hull-less barley grains. Ruminal starch fractional disappearance rates were greatest for hulled barley grains, moderate for hull-less barley grains, and lowest for corn grains (15.3, 13.9, and 7.1%/h, respectively). Ruminal starch half-life was shortest for hulled and hull-less barley grains (4.4 h) and longest for corn grains (6.6 h). Ruminal starch half-life did not differ between hulled barley and hull-less barley grains. In conclusion, using a holistic experimental design and statistical analysis, this study showed that starch from hull-less barley grains has a ruminal half-life similar to that of hulled barley grains and shorter than that of corn grains. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  20. Green shipping management

    CERN Document Server

    Lun, Y H Venus; Wong, Christina W Y; Cheng, T C E

    2016-01-01

    This book presents theory-driven discussion on the link between implementing green shipping practices (GSP) and shipping firm performance. It examines the shipping industry’s challenge of supporting economic growth while enhancing environmental performance. Consisting of nine chapters, the book covers topics such as the conceptualization of green shipping practices (GSPs), measurement scales for evaluating GSP implementation, greening capability, greening and performance relativity (GPR), green management practice, green shipping network, greening capacity, and greening propensity. In view of the increasing quest for environment protection in the shipping sector, this book provides a good reference for firms to understand and evaluate their capability in carrying out green operations on their shipping activities.

  1. Time-domain Hydroelasticity Theory of Ships Responding to Waves

    DEFF Research Database (Denmark)

    Xia, Jinzhu; Wang, Zhaohui

    1997-01-01

    free surface flow. The general interface boundary condition is used in the mathematical formulation of the fluid motion around the flexible structure. The general time-domain theory is simplified to a slender-body theory for the analysis of wave-induced global responses of monohull ships. The structure...... is represented by a non-uniform beam, while the generalized hydrodynamic coefficients can be obtained from two-dimensional potential flow theory. The linear slender body theory is generalized to treat the non-linear loading effects of rigid motion and structural response of ships travelling in rough seas....... The non-linear hydrostatic restoring force and hydrodynamic momentum action are considered. A numerical solution is presented for the slender body theory. Numerical examples are given for two ship cases with different geometry features, a warship hull and the S175 containership with two different bow...

  2. The shipping man adventures in ship finance

    CERN Document Server

    McCleery, Matthew

    2013-01-01

    When restless New York City hedge fund manager Robert Fairchild watches the Baltic Dry Cargo Index plunge 97%, registering an all-time high and a 25-year low within the span of just six months, he decides to buy a ship. Immediately fantasizing about naming a vessel after his wife, carrying a string of worry beads and being able to introduce himself as a "shipowner" at his upcoming college reunion, Fairchild immediately embarks on an odyssey into the most exclusive, glamorous and high stakes business in the world. From pirates off the coast of Somalia and on Wall Street to Greek and Norwegian shipping magnates, the education of Robert Fairchild is an expensive one. In the end, he loses his hedge fund, but he gains a life - as a Shipping Man. Part fast paced financial thriller, part ship finance text book, The Shipping Man is 310 pages of required reading for anyone with an interest in capital formation for shipping.

  3. Approximate convex hull of affine iterated function system attractors

    International Nuclear Information System (INIS)

    Mishkinis, Anton; Gentil, Christian; Lanquetin, Sandrine; Sokolov, Dmitry

    2012-01-01

    Highlights: ► We present an iterative algorithm to approximate affine IFS attractor convex hull. ► Elimination of the interior points significantly reduces the complexity. ► To optimize calculations, we merge the convex hull images at each iteration. ► Approximation by ellipses increases speed of convergence to the exact convex hull. ► We present a method of the output convex hull simplification. - Abstract: In this paper, we present an algorithm to construct an approximate convex hull of the attractors of an affine iterated function system (IFS). We construct a sequence of convex hull approximations for any required precision using the self-similarity property of the attractor in order to optimize calculations. Due to the affine properties of IFS transformations, the number of points considered in the construction is reduced. The time complexity of our algorithm is a linear function of the number of iterations and the number of points in the output approximate convex hull. The number of iterations and the execution time increases logarithmically with increasing accuracy. In addition, we introduce a method to simplify the approximate convex hull without loss of accuracy.

  4. Iron-59 absorption from soy hulls: intrinsic vs extrinsic labeling

    International Nuclear Information System (INIS)

    Lykken, G.I.; Mahalko, J.R.; Nielsen, E.J.; Dintzis, F.R.

    1986-01-01

    As part of an evaluation of the validity of the extrinsic labeling technique for measuring iron absorption, absorption from soy hulls extrinsically labeled ( 59 Fe added to bread dough) was compared with that from soy hulls intrinsically labeled ( 59 Fe incorporated into the soy plant during growth). Century soybeans were grown in a greenhouse. After pods had formed and were filling, each plant was stem injected twice, at 3 day intervals, with 22 μCi 59 Fe as FeCl 2 in 25 μl of 0.5 M HCl solution. After the plants had senesced, the soybeans were harvested, dried, shelled and the hulls removed. Standard meals containing 3.5 mg Fe/meal and up to 0.06 μCi 59 Fe in a soy hull bun were fed on 2 consecutive days to free-living volunteers in a crossover design. Absorption of 59 Fe was greater from intrinsically labeled soy hulls than from extrinsically labeled soy hulls, 20 +/- 20% vs 15 +/- 11% (n=14, p > 0.05 by paired t-test). Apparent absorption ranged from 1.3% to 77% from intrinsically labeled soy hulls and .5% to 29% from extrinsically labeled soy hulls with the highest absorption occurring in persons with low serum ferritin (S.F. < 8 ng/ml). These findings provide additional evidence that the extrinsic labeling method is a valid measure of iron bioavailability to humans

  5. 76 FR 7757 - Hull Identification Numbers for Recreational Vessels

    Science.gov (United States)

    2011-02-11

    ... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Part 181 [Docket No. USCG-2007-29236] Hull Identification Numbers for Recreational Vessels AGENCY: Coast Guard, DHS. ACTION: Follow-up to request for... expanded hull identification number (HIN). The Coast Guard's decision-making process included consideration...

  6. 77 FR 59575 - Hull Identification Numbers for Recreational Vessels

    Science.gov (United States)

    2012-09-28

    ... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Part 181 [Docket No. USCG-2012-0843] Hull Identification Numbers for Recreational Vessels AGENCY: Coast Guard, DHS. ACTION: Request for public comments... requirement to indicate a boat's model year as part of the 12-character Hull Identification Number (HIN...

  7. Determination of digestibility of almond hull in sheep | Yalchi ...

    African Journals Online (AJOL)

    Chemical compositions of almond hull and alfalfa hay were determined. The crude protein (CP), neutral detergent fiber (NDF) and acid detergent fiber (ADF) of almond hull were lower than those of alfalfa hay but the non fibrous carbohydrate (NFC) was more than that of alfalfa hay (3.5 times) (P < 0.01). The dry matter ...

  8. Feasibility of Using Rice Hulls as Bedding for Laboratory Mice.

    Science.gov (United States)

    Carbone, Elizabeth T; Kass, Philip H; Evans, Kristin D

    2016-01-01

    Factors that are considered when selecting laboratory mouse bedding include animal health and comfort, cost, effects on personnel, and bioactive properties. Corncob is economical and facilitates low intracage ammonia but has undesirable influences on some endocrine studies. Rice hulls are an economical material that has not been well characterized as a bedding substrate. In this pilot study, we compared various aspects of bedding performance of rice hulls and other materials. On a per-volume basis, rice hulls were less absorbent than was corncob bedding. Rice hulls had higher odds than did corncob or reclaimed wood pulp of having moisture present at the bedding surface. The results of the absorbency tests coupled with the results of preliminary monitoring of intracage ammonia raised concern about the ability of rice hulls to control ammonia levels sufficiently in cages with high occupancy. However, ammonia was negligible when cages contained 5 young adult female mice. The relative expression of 3 cytochrome p450 genes was compared among mice housed on rice hulls, corncob, reclaimed wood pulp, or pine shavings. The expression of Cyp1a2 was 1.7 times higher in the livers of mice housed on rice hulls than on pine shavings, but other differences were not statistically significant. This study provides information on the merits of rice hulls as laboratory mouse bedding. Their relatively poor moisture control is a major disadvantage that might preclude their widespread use.

  9. Experimental Evaluation of the Hydrodynamic Response of Crew Boat Hulls

    DEFF Research Database (Denmark)

    Pecher, Arthur; Kofoed, Jens Peter

    This report presents the results of an experimental study on 3 different hulls of crew boats intended for service to offshore wind turbines. Their hydrodynamic behaviour has been tested in various sea states representing general wave conditions that could be expected at offshore wind farms. Two...... main setups were used during the tests, corresponding to the hulls being connected to an offshore windmill and being free floating. The following aspects were the main subjects of investigation: • The Response Amplitude Operators of the hulls in two different configurations and with waves coming from 3...... different directions. • The connection forces between the hulls and the wind turbine pile. • The natural frequency of oscillation. For the study, realistic scale models of the hulls of the crew boats were supplied by the client, Hauschildt Marine. The laboratory tests were performed by Arthur Pecher under...

  10. Characterisation of the activities associated with fast reactor cladding hulls

    International Nuclear Information System (INIS)

    Biddle, P.; Rees, J.H.

    1987-01-01

    Four batches of hulls from the reprocessing of fuel from the Prototype Fast Reactor at Dounreay have been examined visually and photographically. The appearance of the hulls (shiny or black) depended on the original location in the fuel pin. The total fissile activities measured corresponded to less than 0.1% or the original fuel. The α-emitter, fission product and activation product activities have been determined from dissolution studies. Profile diagrams have been constructed for the distribution of the principal activities along lengths of seventeen hulls. The evidence obtained suggested that much of the activity on the hulls arose through deposition from the dissolver liquors. The deposits included insoluble particulate material which was thought to be responsible for the wide variations in activity across short lengths of some of the hulls. (orig.)

  11. Marine energy consumption, national economic activity, and greenhouse gas emissions from international shipping

    International Nuclear Information System (INIS)

    Chang, Ching-Chih

    2012-01-01

    The causal relationships among marine energy consumption, greenhouse gas emissions from international shipping, and economic growth for Kyoto Protocol Annex I countries for the period of 1990 to 2006 are discussed. The real gross domestic product is used as a proxy for economic activity. The United States is also discussed because it was the main global polluter before 2006. The co-integration methodology and an error-correction model are used to examine the causal relationships. The empirical results show that marine energy consumption and GDP are the main factors of increased GHG emissions in the short-run, and that economic activity significantly increased emissions in the long-run. Emissions from shipping are more closely related to marine energy consumption than to economic activity. Hence, policies for mitigating greenhouse gas emissions from marine shipping need to focus on greater energy efficiency in the design of ship engines and hulls. - Highlights: ► Energy consumption and GDP are the main causes to increased GHG emissions in the shipping industry. ► Emissions from shipping are more closely related to energy consumption than to GDP. ► Policies to mitigate GHG emissions from shipping industry should focus on the engine and hull design.

  12. Effects of ship's vibration and motion on plant parameters

    International Nuclear Information System (INIS)

    Kakuta, Tsunemi; Kitamura, Toshikatsu; Mizushima, Toshihiko; Yamazaki, Hiroshi; Nakahara, Takeshi; Kamiya, Eisei; Kudou, Takahiro; Naitoh, Akira; Tominaga, Mineo.

    1992-03-01

    Present report was written about the study of the effects of ship's vibration and motion on reactor plant performances measured and analyzed to confirm the total balance for control systems of reactor to propulsion. On July 10, 1990, or on the first day of the first voyage for the power up test, the sea trials of MUTSU, nuclear ship made first in Japan, started from the anchoring test. The trial tests had finished through the third voyage between October 30 and November 9 to the fourth voyage between 7 and 14 of December. The trial tests had been conducted over ten items or so containing in-house tests of the measurements of ship's vibration and motion in order to research the effects on reactor performance. We here call the in-house tests the plant correlation tests. In regard to the correlation with ship's vibration, we confirmed that the inherent vibrations of hull and reactor containment arisen from ship structure had precisely been measured and that the plant correlations due to the hull and local vibrations arising from propeller revolutions are very small. Concerning the correlation with ship's motion, it was shown that her rolling motion strongly had affected on the propulsion system such as shaft power and shaft revolutions. About the correlation with reactor systems it was found that her pitching motion had given effect on the water level in pressurizer, primary coolant average temperature, ε-signal of the auto-control of reactor power and primary coolant pressure etc, particularly, most-strongly on the water level in pressurizer; her rolling and pitching motions had given effect on nuclear characteristics such as reactivity and startup rate; in addition the fluctuation of 0.06 Hz, we think the response inherent in (MUTSU) reactor systems, had been observed on her reactor parameters like reactivity and startup rate, and her propulsion systems like shaft horse power. (author)

  13. Bow hull-form optimization in waves of a 66,000 DWT bulk carrier

    Directory of Open Access Journals (Sweden)

    Jin-Won Yu

    2017-09-01

    Full Text Available This paper uses optimization techniques to obtain bow hull form of a 66,000 DWT bulk carrier in calm water and in waves. Parametric modification functions of SAC and section shape of DLWL are used for hull form variation. Multi-objective functions are applied to minimize the wave-making resistance in calm water and added resistance in regular head wave of λ/L = 0.5. WAVIS version 1.3 is used to obtain wave-making resistance. The modified Fujii and Takahashi's formula is applied to obtain the added resistance in short wave. The PSO algorithm is employed for the optimization technique. The resistance and motion characteristics in calm water and regular and irregular head waves of the three hull forms are compared. It has been shown that the optimal brings 13.2% reduction in the wave-making resistance and 13.8% reduction in the added resistance at λ/L = 0.5; and the mean added resistance reduces by 9.5% at sea state 5.

  14. Optimization of ship inner shell to improve the safety of seagoing transport ship

    Directory of Open Access Journals (Sweden)

    Yan-Yun YU

    2013-09-01

    Full Text Available A practical Ship Inner Shell Optimization Method (SISOM, the purpose of which is to improve the safety of the seagoing transport ship by decreasing the maximum Still Water Bending Moment (SWBM of the hull girder under all typical loading conditions, is presented in this paper. The objective of SISOM is to make the maximum SWBM minimum, and the section areas of the inner shell are taken as optimization variables. The main requirements of the ship performances, such as cargo hold capacity, propeller and rudder immersion, bridge visibility, damage stability and prevention of pollution etc., are taken as constraints. The penalty function method is used in SISOM to change the above nonlinear constraint problem into an unconstrained one, which is then solved by applying the steepest descent method. After optimization, the optimal section area distribution of the inner shell is obtained, and the shape of inner shell is adjusted according to the optimal section area. SISOM is applied to a product oil tanker and a bulk carrier, and the maximum SWBM of the two ships is significantly decreased by changing the shape of inner shell plate slightly. The two examples prove that SISOM is highly efficient and valuable to engineering practice.

  15. Using anti-corrosive paints on ships

    Energy Technology Data Exchange (ETDEWEB)

    Smith, J

    1969-02-07

    Anit-corrosive paints on the outside of ship's hulls fall into 3 groups: the area below the water, the boot- topping area at the waterline, and the weatherwork including the hull and superstructure. Typical formulations of primer and paint are given for use in each section. Anti-corrosion paints must always be considered in conjunction with the kind and amount of surface preparation that can be given. The requirement for faster descaling techniques and higher standards of surface preparation has led to the introduction of automated centrifugal abrasive blasting machines for all new plates and sections. If it is not possible to remove old coatings by abrasive blasting, then the traditional method of chipping followed by wire brushing must be used. The removal of mill scale by abrasive blasting can produce a clean metal surface which is liable to rapid corrosion unless it is painted immediately. A pre-fabrication or shop primer is used which is normally applied by airless spray equipment synchronized with the sand blasting machinery.

  16. Identification of a novel SPLIT-HULL (SPH) gene associated with hull splitting in rice (Oryza sativa L.).

    Science.gov (United States)

    Lee, Gileung; Lee, Kang-Ie; Lee, Yunjoo; Kim, Backki; Lee, Dongryung; Seo, Jeonghwan; Jang, Su; Chin, Joong Hyoun; Koh, Hee-Jong

    2018-07-01

    The split-hull phenotype caused by reduced lemma width and low lignin content is under control of SPH encoding a type-2 13-lipoxygenase and contributes to high dehulling efficiency. Rice hulls consist of two bract-like structures, the lemma and palea. The hull is an important organ that helps to protect seeds from environmental stress, determines seed shape, and ensures grain filling. Achieving optimal hull size and morphology is beneficial for seed development. We characterized the split-hull (sph) mutant in rice, which exhibits hull splitting in the interlocking part between lemma and palea and/or the folded part of the lemma during the grain filling stage. Morphological and chemical analysis revealed that reduction in the width of the lemma and lignin content of the hull in the sph mutant might be the cause of hull splitting. Genetic analysis indicated that the mutant phenotype was controlled by a single recessive gene, sph (Os04g0447100), which encodes a type-2 13-lipoxygenase. SPH knockout and knockdown transgenic plants displayed the same split-hull phenotype as in the mutant. The sph mutant showed significantly higher linoleic and linolenic acid (substrates of lipoxygenase) contents in spikelets compared to the wild type. It is probably due to the genetic defect of SPH and subsequent decrease in lipoxygenase activity. In dehulling experiment, the sph mutant showed high dehulling efficiency even by a weak tearing force in a dehulling machine. Collectively, the results provide a basis for understanding of the functional role of lipoxygenase in structure and maintenance of hulls, and would facilitate breeding of easy-dehulling rice.

  17. Validation of Numerical Predictions of the Impact Forces and Hydrodynamics of a Deep-V Planing Hull

    Science.gov (United States)

    2012-12-01

    technique. NFA uses an implicit subgrid- scale model that is built into the treatment of the convective terms in the momentum equations [14]. A...delivered to SAIC under the Navy DASS (Dynamic Assessment of Surface Ship) 8 NSWCCD-50-TR-2012/040 project in 1998. SLAM2D has two solution methods: (1...is in knots-ft-1/2]. Model Scale Pressure [psi] -0.04 0.0 004 0.08 0.12 0.16 Figure 25. Pressures on hull for CA=0.608, L/b=4 and

  18. Guide to ship sanitation

    National Research Council Canada - National Science Library

    2011-01-01

    "The third edition of the Guide to Ship Sanitation presents the public health significance of ships in terms of disease and highlights the importance of applying appropriate control measures"--Back cover...

  19. Flaxseed hull: Chemical composition and antioxidant activity during development.

    Science.gov (United States)

    Herchi, Wahid; Al Hujaili, Abdullah D; Sakouhi, Faouzi; Sebei, Khaled; Trabelsi, Hajer; Kallel, Habib; Boukhchina, Sadok

    2014-01-01

    Changes in the chemical composition and antioxidant activity of flaxseed hull during maturation were investigated. P129 hull variety was studied at four maturation stages (St1, St2, St3, and St4). Significant variation in proximate composition and flaxseed hull oil characteristics were observed. A significant increase in the carbohydrates content of the hull was observed during development. The main methyl esters were linolenic acid (48.95 - 51.52 %), oleic acid (20.27-23.41%) and linoleic acid (15.62-17.70%). The highest polyunsaturated fatty acids (PUFA) were found to be 67.14 % at the first stage of maturity (St1). Flaxseed hull oil was of good quality, containing an abundance of omega-3 essential fatty acids. The iodine value increased, while the saponification value of oil decreased during seed development. The decrease in ascorbic acid content was steady. The maximum level of total phenolic acid content (128.3 mg/100 g oil) was reached at 7 DAF. The antioxidant activity of oilseed was assessed by means of 2, 2-diphenyl-1-picrylhydrazyl (DPPH) radical-scavenging assay. Radical scavenging activity for green hull was 52.74% and mature hull was 69.32%.

  20. Designing Indonesian Liner Shipping Network

    Directory of Open Access Journals (Sweden)

    Armand Omar Moeis

    2017-06-01

    Full Text Available As the largest archipelago nation in the world, Indonesia’s logistics system has not shown excellence according to the parameters of logistics performance index and based on logistics costs percentages from overall GDP. This is due to the imbalances of trading on the western and eastern regions in Indonesia, which impacts the transportation systems costs to and from the eastern regions. Therefore, it is imperative to improve the competitiveness of Indonesian maritime logistics through maritime logistics network design. This research will focus on three levels of decision making in logistics network design, which include type of ships in the strategic level, shipping routes in the tactical level, and container allocation in the operational level with implementing butterfly routes in Indonesia’s logistics networking problems. Furthermore, this research will analyze the impact of Pendulum Nusantara and Sea Toll routes against the company profits and percentages of containers shipped. This research will also foresee how demand uncertainties and multi-period planning should affect decision making in designing the Indonesian Liner Shipping Network.

  1. 14 CFR 23.533 - Hull and main float bottom pressures.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float bottom pressures. 23... Water Loads § 23.533 Hull and main float bottom pressures. (a) General. The hull and main float....00213; K2=hull station weighing factor, in accordance with figure 2 of appendix I of this part; VS1...

  2. 37 CFR 212.5 - Recordation of distinctive identification of vessel hull designer.

    Science.gov (United States)

    2010-07-01

    ... identification of vessel hull designer. 212.5 Section 212.5 Patents, Trademarks, and Copyrights COPYRIGHT OFFICE, LIBRARY OF CONGRESS COPYRIGHT OFFICE AND PROCEDURES PROTECTION OF VESSEL HULL DESIGNS § 212.5 Recordation of distinctive identification of vessel hull designer. (a) General. Any owner of a vessel hull may...

  3. 14 CFR 29.519 - Hull type rotorcraft: Water-based and amphibian.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull type rotorcraft: Water-based and... § 29.519 Hull type rotorcraft: Water-based and amphibian. (a) General. For hull type rotorcraft, the... along and among the hull and auxiliary floats, if used, in a rational and conservative manner, assuming...

  4. Recycling of merchant ships

    Directory of Open Access Journals (Sweden)

    Magdalena Klopott

    2013-12-01

    Full Text Available The article briefly outlines the issues concerning ship recycling. It highlights ships' high value as sources of steel scrap and non-ferrous metals, without omitting the fact that they also contain a range of hazardous substances. Moreover, the article also focuses on basic ship demolition methods and their environmental impact, as well as emphasizes the importance of “design for ship recycling” philosophy.

  5. A NUMERICAL APPLICATION TO PREDICT THE RESISTANCE AND WAVE PATTERN OF KRISO CONTAINER SHIP

    Directory of Open Access Journals (Sweden)

    Yavuz Hakan Ozdemir

    2016-06-01

    Full Text Available In this study, the computational results for KRISO Container Ship (KCS are presented. CFD analyses are performed to simulate free surface flow around KCS by using RANS approach with success. Also the complicated turbulent flow zone behind the ship is well simulated. The RANS equations and the non-linear free surface boundary conditions are discretized by means of a finite volume scheme. The numerical methodology is found to be appropriate for simulating the turbulent flow around a ship in order to estimate ship total resistance and free surface. By the numerical results, total resistance is calculated for the ship model and the result is satisfactory with regard to the experimental one. As a result of well captured free surface, the wave elevation on/around the hull is compared with the experimental results.

  6. Effect of dietary trace mineral supplementation and a multi-element trace mineral injection on shipping response and growth performance of beef cattle.

    Science.gov (United States)

    Genther, O N; Hansen, S L

    2014-06-01

    To examine the effect of trace mineral (TM) status and TM injection on growth performance and carcass characteristics in beef cattle, 40 steers were used in a growing and finishing study. Steers were stratified by weight (323 ± 14.8 kg) and assigned to 1 of 2 treatments for an 84-d depletion period: 1) a corn silage-based diet supplemented with Cu, Mn, Se, and Zn to meet or exceed NRC recommendations (CON), or 2) CON diet without supplemental Cu, Mn, Se, or Zn but supplemented with 300 mg Fe and 5 mg Mo/kg diet DM as dietary TM antagonists (DEF) to induce mild deficiencies. To mimic shipping stress, steers were shipped for 20 h on d 88 and were received back on d 89. On d 91 an equal number of steers from both dietary treatments were injected with sterilized saline (SAL) or Multimin 90 (MM; containing 15, 60, 10, and 5 mg/mL of Cu, Zn, Mn, and Se, respectively) at a dose of 1 mL/68 kg BW. Steers were fed a common finishing diet supplemented with 10 mg Cu, 20 mg Mn, 0.1 mg Se, and 30 mg Zn/kg diet DM for the 90-d repletion period. Steers were harvested 91 d postinjection and carcass data were collected. During the depletion period, diet did not affect BW, ADG, DMI, or G:F (P > 0.20). During the shipping period (defined as the time between 2-d consecutive weights on d 83 and 84 and d 90 and 91), DEF steers tended to lose more weight per day than CON steers (P = 0.06) and had lesser DMI (P = 0.03), suggesting that response to shipping stress may be modulated by TM status. During the repletion period, ADG of DEF + MM steers was greater (P = 0.03) compared with DEF + SAL and was not different (P = 0.92) among CON + MM and CON + SAL steers. There was no effect of diet or injection on HCW or dressing percentage (P > 0.20). Within the CON group, TM injection decreased yield grade (P = 0.03) but did not affect yield grade of DEF steers (P > 0.20). Steers given TM injection had a larger rib eye area (P = 0.04) regardless of previous diet. Interestingly, both diet and

  7. Preparation and characterization of rice hull silica products

    International Nuclear Information System (INIS)

    Quirit, Leni L.; Llaguno, Elma C.; Pagdanganan, Fernando C.; Hernandez, Karen N.

    2008-01-01

    Rice hull is an abundant agricultural waste material which could be a renewable energy source when combusted. The combustion residue (called rice hull ash or RHA) contains a significant amount (20% of the hull) of potentially high grade silica. Silica gels prepared from rice hull were found to have properties comparable to two commercial desiccant silica gels (Blue Merck and FNG-A) in terms of chemical and amorphous structure, surface area, desiccant characteristics, microstructure and heats of adsorption. These properties were determined from water vapor adsorption measurements, electron microscopy, and from infrared and x-ray diffraction spectra. The acid treated rice hull gels were found to have fewer elemental impurities detected by qualitative x-ray fluorescence, compared to the commercial gels. Thermogravimetric analysis (TGA) data showed that this technique can also be used to indirectly compare impurity levels in the samples, in terms of the amorphous to crystalline phase transition. Using an improved acid treatment method, a silica gel sample was prepared from rice hull and compared to three commercial chromatographic silica gels using quantitative elemental x-ray fluorescence analysis. Elemental levels in the rice hull gel were within the range of levels or close to the detection limits of corresponding elements in the chromatographic gels. Water vapor adsorption, x-ray diffraction, infrared spectroscopy and scanning electron microscopy showed that the rice hull gel was similar to the commercial chromatographic silica gel Davison 12. Zeolites are crystalline aluminosilicates used as molecular sieves for purification and catalytic purposes. Zeolites X and Y were synthesized from rice hull silica gel and aluminum hydroxide. For comparison, controls were synthesized from commercial silica gel. The samples and controls exhibited characteristics infrared peaks corresponding to the vibrations of the TO 4 (T=Si, Al) of the zeolite framework. The x

  8. Dutch Ships and Sailors

    NARCIS (Netherlands)

    de Boer, Victor; Hoekstra, F.G.; Leinenga, Jurjen; van Rossum, Matthias

    2014-01-01

    Dutch Ships and Sailors provides an infrastructure for maritime historical datasets, linking correlating data through semantic web technology. It brings together datasets related to recruitment and shipping in the East-India trade (mainly 18th century) and in the shipping of the northern provinces

  9. Reactors. Nuclear propulsion ships

    International Nuclear Information System (INIS)

    Fribourg, Ch.

    2001-01-01

    This article has for object the development of nuclear-powered ships and the conception of the nuclear-powered ship. The technology of the naval propulsion P.W.R. type reactor is described in the article B.N.3 141 'Nuclear Boilers ships'. (N.C.)

  10. Ship-to-Ship Radiocommunication Trial by Using Wireless LAN

    Directory of Open Access Journals (Sweden)

    Yasuyuki Niwa

    2015-12-01

    In a former field radiocommunication trial, omni-directional antennas were used and a few hundred kbps throughput between two ships was measured, which was not enough for our research target (over 1Mbps. In order to get faster throughput, a field radiocommunication trial was carried out again with a few types of directional antennas and RSSI (Received Signal Strength Indication and the throughput between two ships was measured simultaneously. As a result, multi-path (2-path model affected by the reflection of the sea surface was confirmed and also the characteristics of the directional antennas such as half-power angle were confirmed, but the measured throughput was fast enough to meet our expectation.

  11. The study on radioactivity reduction of spent PWR cladding hull

    International Nuclear Information System (INIS)

    Jung, I. H.; Kim, J. H.; Park, C. J.; Jung, Y. H.; Song, K. C.; Lee, J. W.; Park, J. J.; Yang, M. S.

    2003-01-01

    Hull arising from the spent PWR fuel elements is classified as a high-level radioactive waste. This report describes the radio-chemical characteristics of the hull-from PWR spent fuel of 32,000MWd/tU burn-up and 15 years cooling, discharged from Gori Unit I cycled 4-7-by examination and literature survey. On the basis of the results, a method of degradation to middle and low-level radioactive waste was proposed by dry process such as laser or plasma technique with removing the nuclides deposited on the surface of the hull

  12. Corn fiber hulls as a food additive or animal feed

    Science.gov (United States)

    Abbas, Charles; Beery, Kyle E.; Cecava, Michael J.; Doane, Perry H.

    2010-12-21

    The present invention provides a novel animal feed or food additive that may be made from thermochemically hydrolyzed, solvent-extracted corn fiber hulls. The animal feed or food additive may be made, for instance, by thermochemically treating corn fiber hulls to hydrolyze and solubilize the hemicellulose and starch present in the corn fiber hulls to oligosaccharides. The residue may be extracted with a solvent to separate the oil from the corn fiber, leaving a solid residue that may be prepared, for instance by aggolmerating, and sold as a food additive or an animal feed.

  13. Nuclear merchant ship propulsion

    International Nuclear Information System (INIS)

    Schroeder, E.; Jager, W.; Schafstall, H.G.

    1977-01-01

    The operation of about 300 nuclear naval vessels has proven the feasibility of nuclear ship propulsion. Until now six non military ships have been built or are under construction. In the Soviet Union two nuclear icebreakers are in operation, and a third one is under construction. In the western world three prototype merchant ships have been built. Of these ships only the NS OTTO HAHN is in operation and provides valuable experience for future large scale use of nuclear merchant ship propulsion. In many countries studies and plans are made for future nuclear merchant ships. Types of vessels investigated are large containerships, tankers and specialized ships like icebreakers or ice-breaking ships. The future of nuclear merchant ship propulsion depends on three interrelated items: (1) nuclear ship technology; (2) economy of nuclear ship propulsion; (3) legal questions. Nuclear merchant ship technology is based until now on standard ship technology and light water reactor technology. Except for special questions due to the non-stationary type of the plant entirely new problems do not arise. This has been proven by the recent conceptual licensing procedure for a large nuclear containership in Germany. The economics of nuclear propulsion will be under discussion until they are proven by the operation of privately owned lead ships. Unsolved legal questions e.g. in connection with port entry permissions are at present another problem for nuclear shipping. Efforts are made to solve these questions on an international basis. The future development of nuclear energy electricity production in large land based plants will stimulate the employment of smaller units. Any future development of long distance sea transport will have to take this opportunity of a reliable and economic energy supply into account

  14. "Keisri hull" kui müstiline fantasy / Siimon Prii

    Index Scriptorium Estoniae

    Prii, Siimon

    2006-01-01

    30. sept. Ugalas esietendunud Jaan Krossi "Keisri hull" (autoridramatiseering), lavastajad Jaak Allik ja Peeter Tammearu. Kunstnik on Jaanus Laagriküll ja muusikaline kujundaja Peeter Konovalov. Peaosas Peeter Tammearu

  15. Safety Evaluation for Hull Waste Treatment Process in JNC

    International Nuclear Information System (INIS)

    Kojima, H.; Kurakata, K.

    2002-01-01

    Hull wastes and some scrapped equipment are typical radioactive wastes generated from reprocessing process in Tokai Reprocessing Plant (TRP). Because hulls are the wastes remained in the fuel shearing and dissolution, they contain high radioactivity. Japan Nuclear Cycle Development Institute (JNC) has started the project of Hull Waste Treatment Facility (HWTF) to treat these solid wastes using compaction and incineration methods since 1993. It is said that Zircaloy fines generated from compaction process might burn and explode intensely. Therefore explosive conditions of the fines generated in compaction process were measured. As these results, it was concluded that the fines generated from the compaction process were not hazardous material. This paper describes the outline of the treatment process of hulls and results of safety evaluation

  16. Opvoeders se persepsies van hulle werkmotivering: 'n kwalitatiewe ...

    African Journals Online (AJOL)

    Erna Kinsey

    Individue voel dat hulle self geen beheer oor die proses het nie en dat die verandering van buite ...... treatment has a negative influence on their self-esteem and moti- vation. ... tion, especially since the abolishment of corporal punishment.

  17. Soybean hulls as an iron source for bread enrichment

    International Nuclear Information System (INIS)

    Johnson, C.D.; Berry, M.F.; Weaver, C.M.

    1985-01-01

    Soybean hulls, a concentrated source of iron, may have potential as a source of iron fortification in baked products. Retention of 59 Fe in rats from white bread containing intrinsically labeled soybean hulls did not differ significantly (p<0.05) from extrinsically labeled white bread fortified with bakery grade ferrous sulfate (70.4 and 63.1%, respectively). Physical and sensory evaluations of bread containing up to 5% soybean hulls did not differ from white bread in loaf volume, cross-sectional area, tenderness or overall acceptance. These results suggest that soybean hulls are a good source of available iron and may be added to bakery products without deleterious effects in baking performance and sensory acceptability

  18. Use of Jatropha curcas hull biomass for bioactive compost production

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, D.K. [Division of Environmental Sciences, Indian Agricultural Research Institute, New Delhi 110012 (India); Pandey, A.K.; Lata [Division of Microbiology, Indian Agricultural Research Institute, New Delhi 110012 (India)

    2009-01-15

    The paper deals with utilization of biomass of Jatropha hulls for production of bioactive compost. In the process of Jatropha oil extraction, a large amount of hull waste is generated. It has been found that the direct incorporation of hull into soil is considerably inefficient in providing value addition to soil due to its unfavorable physicochemical characteristics (high pH, EC and phenolic content). An alternative to this problem is the bioconversion of Jatropha hulls using effective lignocellulolytic fungal consortium, which can reduce the phytotoxicity of the degraded material. Inoculation with the fungal consortium resulted in better compost of jatropha hulls within 1 month, but it takes nearly 4 months for complete compost maturation as evident from the results of phytotoxicity test. Such compost can be applied to the acidic soil as a remedial organic manure to help maintaining sustainability of the agro-ecosystem. Likewise, high levels of cellulolytic enzymes observed during bioconversion indicate possible use of fungi for ethanol production from fermentation of hulls. (author)

  19. Preconditioning 2D Integer Data for Fast Convex Hull Computations.

    Science.gov (United States)

    Cadenas, José Oswaldo; Megson, Graham M; Luengo Hendriks, Cris L

    2016-01-01

    In order to accelerate computing the convex hull on a set of n points, a heuristic procedure is often applied to reduce the number of points to a set of s points, s ≤ n, which also contains the same hull. We present an algorithm to precondition 2D data with integer coordinates bounded by a box of size p × q before building a 2D convex hull, with three distinct advantages. First, we prove that under the condition min(p, q) ≤ n the algorithm executes in time within O(n); second, no explicit sorting of data is required; and third, the reduced set of s points forms a simple polygonal chain and thus can be directly pipelined into an O(n) time convex hull algorithm. This paper empirically evaluates and quantifies the speed up gained by preconditioning a set of points by a method based on the proposed algorithm before using common convex hull algorithms to build the final hull. A speedup factor of at least four is consistently found from experiments on various datasets when the condition min(p, q) ≤ n holds; the smaller the ratio min(p, q)/n is in the dataset, the greater the speedup factor achieved.

  20. Grene and Hull on types and typological thinking in biology.

    Science.gov (United States)

    Honenberger, Phillip

    2015-04-01

    Marjorie Grene (1910-2009) and David Hull (1935-2010) were among the most influential voices in late twentieth-century philosophy of biology. But, as Grene and Hull pointed out in published discussions of one another's work over the course of nearly forty years, they disagreed strongly on fundamental issues. Among these contested issues is the role of what is sometimes called "typology" and "typological thinking" in biology. In regard to taxonomy and the species problem, Hull joined Ernst Mayr's construal of typological thinking as a backward relic of pre-Darwinian science that should be overcome. Grene, however, treated the suspicion of typological thinking that characterized Hull's views, as well as those of other architects of the New Evolutionary Synthesis, as itself suspicious and even unsustainable. In this paper I review three debates between Grene and Hull bearing on the question of the validity of so-called typological thinking in biology: (1) a debate about the dispensability of concepts of "type" within evolutionary theory, paleontology, and taxonomy; (2) a debate about whether species can be adequately understood as individuals, and thereby independently of those forms of thinking Hull and Mayr had construed as "typological"; and (3) a debate about the prospects of a biologically informed theory of human nature. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Treatment of zircaloy cladding hulls by isostatic pressing

    International Nuclear Information System (INIS)

    Tegman, R.; Burstroem, M.

    1984-12-01

    A method for the treatment of Zircaloy fuel hulls is proposed. It involves hot isostatic pressing (HIP) for making large, completely densified metallic bodies of the waste. The hulls are packed into a bellows-shaped container of steel. On packing the fuel hulls give a filling factor of only 14%, which is too low for non-deformable compaction in a normal container, but by using a belloped container, a non-deformable compaction can be obtained without any pretreatment of the hulls. Fully dense and mechanically strong blocks of Zircaloy can be fabricated by holding them at temperatures of around 1000 degrees C for three hours. It is also feasible to incorporate the other metallic parts of the fuel bundle, such as top and bottom tie plates and spacers, in the pressing. The HIP-densified hulls provide an effective means of self-containment of radioactive waste due to the excellent corrosion resistance of Zircaloy. A waste loading factor of close to 100% can be realized. Futher, a volume reduction factor of 7 and a surface reduction factor of aout 250 for a 1-ton canister can be achieved. Equilibrium calculations have shown that tritium present in the hulls can quantitatively be contained in the HIPed block. A study has been made of a possible process for industrilscale use. (Author)

  2. Safety of nuclear ships

    International Nuclear Information System (INIS)

    1978-01-01

    Interest in the utilization of nuclear steam supply systems for merchant ships and icebreakers has recently increased considerably due to the sharp rise in oil prices and the continuing trend towards larger and faster merchant ships. Canada, for example, is considering construction of an icebreaker in the near future. On the other hand, an accident which could result in serious damage to or the sinking of a nuclear ship is potentially far more dangerous to the general public than a similar accident with a conventional ship. Therefore, it was very important to evaluate in an international forum the safety of nuclear ships in the light of our contemporary safety philosophy, taking into account the results of cumulative operating experience with nuclear ships in operation. The philosophy and safety requirement for land-based nuclear installations were outlined because of many common features for both land-based nuclear installations and nuclear ships. Nevertheless, essential specific safety requirements for nuclear ships must always be considered, and the work on safety problems for nuclear ships sponsored by the NEA was regarded as an important step towards developing an international code of practice by IMCO on the safety of nuclear merchant ships. One session was devoted to the quantitative assessment of nuclear ship safety. The probability technique of an accident risk assessment for nuclear power plants is well known and widely used. Its modification, to make it applicable to nuclear propelled merchant ships, was discussed in some papers. Mathematical models for describing various postulated accidents with nuclear ships were developed and reported by several speakers. Several papers discussed a loss-of-coolant accident (LOCA) with nuclear steam supply systems of nuclear ships and engineering design features to prevent a radioactive effluence after LOCA. Other types of postulated accidents with reactors and systems in static and dynamic conditions were also

  3. Regional Sediment Management Studies of Matagorda Ship Channel and Matagorda Bay System, Texas

    Science.gov (United States)

    2013-08-01

    undisturbed free water surface.” The USACE presently has no standardized method to measure the fluid mud to determine nautical depth. The Engineer Manual...structural member in the bottom of the hull and channel bottom) is used to account for parameters such as ship motion from waves, squat , safety...distance between the nautical bottom and undisturbed free water surface. To complete the definition of nautical bottom, the physical characteristic(s) on

  4. Estimating Weight and Moments for Ship Control Design Technical Assessment Team Reviews

    Science.gov (United States)

    2016-07-26

    2. Bow: The front of a ship. See Figure 1 & 2. Centerline: A vertical plane through the center of the hull. See Figure 2. Compartment Number: Often...service life allowances early in life, will be put into a critical status if the rate of consumption is too high. If a class has managed to reduce...an initially high rate of consumption to a moderate level it may be allowed to revert to a less critical status. Stability Status Definition 1 No

  5. Littoral Combat Ship: Additional Testing and Improved Weight Management Needed Prior to Further Investments

    Science.gov (United States)

    2014-07-01

    monohull design with a steel hull and aluminum superstructure, while the Austal USA Independence variant (LCS 2 and other even- Background Seaframe...including Singapore; Malaysia ; Brunei; and Indonesia. The ship also conducted some real-world operations as directed by the 7th Fleet, such as...requirements for service life allowances already fall short of the growth margins called for under Navy and industry recommended practice.21 Table 8: Navy

  6. Decommissioning plan of the nuclear-powered ship 'Mutsu'

    International Nuclear Information System (INIS)

    1992-01-01

    The nuclear-powered ship 'Mutsu' is to be decommissioned at Sekinehama Port immediately after finishing the experimental voyage based on the 'Fundamental plan on the research required for the development of nuclear ships in Japan Atomic Energy Research Institute' decided in March, 1985. The decommissioning plan which determines the methods of the works regarding the decommissioning and others is as follows. In order to utilize the ship hull of Mutsu, the reactor room including the reactor and shielding is removed in a lump, and the removal and isolation method of preserving it as it is on land is adopted. The measures for environment preservation and ensuring the safety of residents are taken, and the sufficient work control is carried out for preventing accidents and reducing the radiation exposure of workers. The ship is used as the ship with ordinary propulsion system for ocean research and the research and development of marine reactors. The utilization of Sekinehama and Ominato facilities is investigated. The reactor room removed from Mutsu is exhibited to public, being preserved safely in a building. (K.I.)

  7. Required grades of hull steel plates in consideration of fracture toughness; Hakai jinsei wo koryoshita sentaiyo koban shiyo kubun ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yajima, H; Yamamoto, M; Ogaki, Y [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1997-10-01

    This paper discusses the required grades of hull steel plates based on the steel ship rule of Nippon Kaiji Kyokai (NK). The minimum value of the allowable crack length in NK rule (critical safety crack length at 0degC just before brittle unstable crack causing fatal fracture) was estimated. In the case where the estimated crack tip exists in a matrix, the crack length was a minimum of 200-210mm, while nearly 60mm in a fusion line at high-heat-input welded joint. The allowable crack lengths estimated from a specified value in the NK rule were fairly different. The allowable crack length at 0degC was also estimated from the minimum value in V-notch Charpy impact test. The private proposal on the required grades of hull steel plates in consideration of fracture toughness was discussed. Thirty-five percent of crack lengths found in real ships is 100mm or less, however, cracks of 250-400mm long are frequently found suggesting the allowable crack length of 400mm. The required grade integrally considering required values and design conditions is demanded to secure the reliability of hull strength. 5 refs., 5 figs., 2 tabs.

  8. Evaluation of the biological activity of sunflower hull extracts

    Energy Technology Data Exchange (ETDEWEB)

    Taha, F. S.; Wagdy, S. M.; Hassanein, M. M. M.; Hamed, S. F.

    2012-11-01

    This work was planned with the aim of adding value to sunflower seed hulls, a waste product of the oil industry by preparing a sunflower hull phenolic extract rich in chlorogenic acid (CGA). In order to fulfill this goal, the optimization for the extraction of a phenolic extract from the hulls was investigated. The parameters studied were: type of solvent, solvent to water ratio and hull to solvent ratio. In addition, the solvent mixtures were also studied. The resulting phenolic extracts were evaluated for their biological activities. This included phenolic content determination, evaluation of the antioxidant and antimicrobial activities. Chlorogenic acid was determined in two chosen hull extracts using the UV spectrophotometric method and HPLC analysis. The anti carcinogenic activity of the two chosen extracts was tested on seven different cell line carcinomas. The results revealed that all the phenolic extracts of sunflower hull studied contain between 190-312.5 mg phenolics/ 100 g hulls. The highest phenolic extraction was achieved with 80% methanol (1:30, hull to solvent, w/v ratio) and methanol to ethanol to water (7:7:6 v/v/v) mixture with values of 312.5 and 306.5 mg phenolics/100 g hulls, respectively. The free radical scavenging activity and antioxidant activity of all the samples ranged from 33.6-72.6%. The highest antioxidant activity and free radical scavenging activity were achieved by the same extracts that possessed the highest phenolic content, namely methanol to ethanol to water extract and 80% methanol with values 71.8 and 72.6%, 68.2 and 70.9% respectively, compared to 77.9 and 76.9% respectively for TBHQ. All the phenolic extracts possessed antimicrobial activity but to different levels against different pathogenic bacteria. The two chosen extracts also possessed anti carcinogenic activity, which differed among varying cell line carcinomas. The HPLC analysis indicated that chlorogenic acid was the main phenolic acid in the extract. Thus it can

  9. Numerical Ship Hydrodynamics : an assessment of the Gothenburg 2010 Workshop

    CERN Document Server

    Stern, Frederick; Visonneau, Michel

    2014-01-01

    This book assesses the state-of-the-art in computational fluid dynamics (CFD) applied to ship hydrodynamics and provides guidelines for the future developments in the field based on the Gothenburg 2010 Workshop. It presents ship hull test cases, experimental data and submitted computational methods, conditions, grids and results.  Analysis is made of errors for global (resistance, sinkage and trim and self-propulsion) and local flow (wave elevations and mean velocities and turbulence) variables, including standard deviations for global variables and propeller modeling for self-propulsion. The effects of grid size and turbulence models are evaluated for both global and local flow variables. Detailed analysis is made of turbulence modeling capabilities for capturing local flow physics. Errors are also analyzed for head-wave seakeeping and forward speed diffraction, and calm-water forward speed-roll decay. Resistance submissions are used to evaluate the error and uncertainty by means of a systematic verificatio...

  10. Underwater Ship Husbandry Discharges

    Science.gov (United States)

    2011-11-01

    which entered into force in September of 2008, prohibits the use of harmful organotins such as tributyltin ( TBT ) in AFCs used on international...States. The use of TBT AFCs is explicitly prohibited under the VGP, and vessels must remove such coatings or paint over them to prevent toxic ...to hull husbandry include (1) the discharge of toxic chemicals used as biocides in AFCs and (2) biofouling as a vector for aquatic nuisance species

  11. Prediction of noise in ships by the application of “statistical energy analysis.”

    DEFF Research Database (Denmark)

    Jensen, John Ødegaard

    1979-01-01

    If it will be possible effectively to reduce the noise level in the accomodation on board ships, by introducing appropriate noise abatement measures already at an early design stage, it is quite essential that sufficiently accurate prediction methods are available for the naval architects...... or for a special noise abatement measure, e.g., increased structural damping. The paper discusses whether it might be possible to derive an alternative calculation model based on the “statistical energy analysis” approach (SEA). By considering the hull of a ship to be constructed from plate elements connected...

  12. Air Entrainment and Surface Ripples in a Turbulent Ship Hull Boundary Layer

    Science.gov (United States)

    Masnadi, Naeem; Erinin, Martin; Duncan, James H.

    2017-11-01

    The air entrainment and free-surface fluctuations caused by the interaction of a free surface and the turbulent boundary layer of a vertical surface-piercing plate is studied experimentally. In this experiment, a meter-wide stainless steel belt travels horizontally in a loop around two rollers with vertically oriented axes. This belt device is mounted inside a large water tank with the water level set just below the top edge of the belt. The belt, rollers, and supporting frame are contained within a sheet metal box to keep the device dry except for one 6-meter-long straight test section. The belt is accelerated suddenly from rest until reaching constant speed in order to create a temporally evolving boundary layer analogous to the spatially evolving boundary layer that would exist along a surface-piercing towed flat plate. Surface ripples are measured using a cinematic laser-induced fluorescence technique with the laser sheet oriented parallel or normal to the belt surface. Air entrainment events and bubble motions are recorded from underneath the water surface using a stereo imaging system. Measurements of small bubbles, that tend to stay submerged for a longer time, are planned via a high-speed digital in-line holographic system. The support of the Office of Naval Research is gratefully acknowledged.

  13. Wideband Detection and Classification of Mines in a Simulated ship Hull Scenario

    Science.gov (United States)

    2007-12-01

    Résumé …..... Ce rapport décrit une expérience au cours de laquelle nous avons placé un petit contenant de plastique contenant un mélange d’époxyde...décrit une expérience au cours de laquelle nous avons placé un petit contenant de plastique contenant un mélange d’époxyde-caoutchouc et de billes

  14. Buckling of Ship Structures

    CERN Document Server

    Shama, Mohamed

    2013-01-01

    Buckling of Ship Structures presents a comprehensive analysis of the buckling problem of ship structural members. A full analysis of the various types of loadings and stresses imposed on ship plating and primary and secondary structural members is given. The main causes and consequences of the buckling mode of failure of ship structure and the methods commonly used to control buckling failure are clarified. This book contains the main equations required to determine the critical buckling stresses for both ship plating and the primary and secondary stiffening structural members. The critical buckling stresses are given for ship plating subjected to the induced various types of loadings and having the most common boundary conditions encountered in ship structures.  The text bridges the gap existing in most books covering the subject of buckling of ship structures in the classical analytical format, by putting the emphasis on the practical methods required to ensure safety against buckling of ship structur...

  15. Hull loss accident model for narrow body commercial aircraft

    Directory of Open Access Journals (Sweden)

    Somchanok Tiabtiamrat

    2010-10-01

    Full Text Available Accidents with narrow body aircraft were statistically evaluated covering six families of commercial aircraft includingBoeing B737, Airbus A320, McDonnell Douglas MD80, Tupolev TU134/TU154 and Antonov AN124. A risk indicator for eachflight phase was developed based on motion characteristics, duration time, and the presence of adverse weather conditions.The estimated risk levels based on these risk indicators then developed from the risk indicator. Regression analysis indicatedvery good agreement between the estimated risk level and the accident ratio of hull loss cases per number of delivered aircraft.The effect of time on the hull loss accident ratio per delivered aircraft was assessed for B737, A320 and MD80. Equationsrepresenting the effect of time on hull loss accident ratio per delivered aircraft were proposed for B737, A320, and MD80,while average values of hull loss accident ratio per delivered aircraft were found for TU134, TU154, and AN 124. Accidentprobability equations were then developed for each family of aircraft that the probability of an aircraft in a hull loss accidentcould be estimated for any aircraft family, flight phase, presence of adverse weather factor, hour of day, day of week, monthof year, pilot age, and pilot flight hour experience. A simplified relationship between estimated hull loss accident probabilityand unsafe acts by human was proposed. Numerical investigation of the relationship between unsafe acts by human andfatality ratio suggested that the fatality ratio in hull loss accident was dominated primarily by the flight phase media.

  16. Survival of ship biofouling assemblages during and after voyages to the Canadian Arctic.

    Science.gov (United States)

    Chan, Farrah T; MacIsaac, Hugh J; Bailey, Sarah A

    2016-01-01

    Human-mediated vectors often inadvertently translocate species assemblages to new environments. Examining the dynamics of entrained species assemblages during transport can provide insights into the introduction risk associated with these vectors. Ship biofouling is a major transport vector of nonindigenous species in coastal ecosystems globally, yet its magnitude in the Arctic is poorly understood. To determine whether biofouling organisms on ships can survive passages in Arctic waters, we examined how biofouling assemblage structure changed before, during, and after eight round-trip military voyages from temperate to Arctic ports in Canada. Species richness first decreased (~70% loss) and then recovered (~27% loss compared to the original assemblages), as ships travelled to and from the Arctic, respectively, whereas total abundance typically declined over time (~55% total loss). Biofouling community structure differed significantly before and during Arctic transits as well as between those sampled during and after voyages. Assemblage structure varied across different parts of the hull; however, temporal changes were independent of hull location, suggesting that niche areas did not provide protection for biofouling organisms against adverse conditions in the Arctic. Biofouling algae appear to be more tolerant of transport conditions during Arctic voyages than are mobile, sessile, and sedentary invertebrates. Our results suggest that biofouling assemblages on ships generally have poor survivorship during Arctic voyages. Nonetheless, some potential for transporting nonindigenous species to the Arctic via ship biofouling remains, as at least six taxa new to the Canadian Arctic, including a nonindigenous cirripede, appeared to have survived transits from temperate to Arctic ports.

  17. Investigation on coupling error characteristics in angular rate matching based ship deformation measurement approach

    Science.gov (United States)

    Yang, Shuai; Wu, Wei; Wang, Xingshu; Xu, Zhiguang

    2018-01-01

    The coupling error in the measurement of ship hull deformation can significantly influence the attitude accuracy of the shipborne weapons and equipments. It is therefore important to study the characteristics of the coupling error. In this paper, an comprehensive investigation on the coupling error is reported, which has a potential of deducting the coupling error in the future. Firstly, the causes and characteristics of the coupling error are analyzed theoretically based on the basic theory of measuring ship deformation. Then, simulations are conducted for verifying the correctness of the theoretical analysis. Simulation results show that the cross-correlation between dynamic flexure and ship angular motion leads to the coupling error in measuring ship deformation, and coupling error increases with the correlation value between them. All the simulation results coincide with the theoretical analysis.

  18. Crushing Strength of Ship Structures

    DEFF Research Database (Denmark)

    Cerup-Simonsen, Bo; Abramowicz, W.; Høstgaard-Brene, C.N.S.

    1999-01-01

    The crushing response of ship structures is of primary importance to the designers and practicing engineers concerned with accidental loading and accident reconstruction of marine vehicles. Ship to-ship collisions, ship-harbor infrastructure interaction or ship-offshore structure interaction are ...

  19. An analytical method to assess the damage and predict the residual strength of a ship in a shoal grounding accident scenario

    Directory of Open Access Journals (Sweden)

    Sun Bin

    2016-04-01

    Full Text Available In this paper, a simplified analytical method used to predict the residual ultimate strength of a ship hull after a shoal grounding accident is proposed. Shoal grounding accidents always lead to severe denting, though not tearing, of the ship bottom structure, which may threaten the global hull girder resistance and result in even worse consequences, such as hull collapse. Here, the degree of damage of the bottom structure is predicted by a series of analytical methods based on the plastic-elastic deformation mechanism. The energy dissipation of a ship bottom structure is obtained from individual components to determine the sliding distance of the seabed obstruction. Then, a new approach to assess the residual strength of the damaged ship subjected to shoal grounding is proposed based on the improved Smith's method. This analytical method is verified by comparing the results of the proposed method and those generated by numerical simulation using the software ABAQUS. The proposed analytical method can be used to assess the safety of a ship with a double bottom during its design phase and predict the residual ultimate strength of a ship after a shoal grounding accident occurs.

  20. Investigation of impact phenomena on the marine structures: Part II - Internal energy of the steel structure applied by selected materials in the ship-ship collision incidents

    Science.gov (United States)

    Prabowo, A. R.; Baek, S. J.; Lee, S. G.; Bae, D. M.; Sohn, J. M.

    2018-01-01

    Phenomena of impact loads on the marine structures has attracted attention to be predicted regarding its influences to structural damage. This part demands sustainable analysis and observation as tendency may vary from one to others since impact involves various scenario models and the structure itself experiences continuous development. Investigation of the damage extent can be conducted by observation on the energy behaviour during two entities involve in a contact. This study aimed to perform numerical investigation to predict structural damage by assessing absorbed strain energy represented by the internal energy during a series of ship collisions. The collision target in ship-ship interactions were determined on the single and double hulls part of a passenger ship. Tendency of the internal energy by the steel structures was summarized, and verification was presented by several crashworthiness criteria. It was found that steel structures applied by the material grades A and B produced different tendencies compared to the material grades D and E. Effect of the structural arrangement to structural responses in terms of strain and stress indicated that the single hull presented contour expansion mainly on the longitudinal directions.

  1. The Evaluation of Cone Capsule as an Alternative Hull form for Portable Tsunami Lifeboat to Support Evacuation System in the Coastal Regions and Small Islands

    Science.gov (United States)

    Fauzan Zakki, Ahmad; Suharto; Windyandari, Aulia

    2018-03-01

    Several attempts have been made to reduce the risk of tsunami disasters such as the development of early warning systems, evacuation procedures training, coastal protection and coastal spatial planning. Although many efforts to mitigate the impact of the tsunami in Indonesia was made, no one has developed a portable disaster rescue vehicle/shelter as well as a lifeboat on ships and offshore building, which is always available when a disaster occurs. The aim of the paper is to evaluate the performance of cone capsule shaped hull form that would be used for the portable tsunami lifeboat. The investigation of the boat resistance, intact stability, and seakeeping characteristics was made. The numerical analysis results indicate that the cone capsule is reliable as an alternative hull form for the portable tsunami lifeboat.

  2. Shipping Information Pipeline

    DEFF Research Database (Denmark)

    Jensen, Thomas; Vatrapu, Ravi

    2015-01-01

    and national borders within international shipping which is a rather complex domain. The intellectual objective is to generate and evaluate the efficacy and effectiveness of design principles for inter-organizational information infrastructures in the international shipping domain that can have positive...

  3. Liner Shipping Fleet Repositioning

    DEFF Research Database (Denmark)

    Tierney, Kevin; Jensen, Rune Møller

    2011-01-01

    Liner shipping fleet repositioning consists of moving vessels between services in a liner ship- ping network in order to better orient the overall network to the world economy, and to ensure the proper maintenance of vessels. Thus, fleet repositioning involves sailing and loading activities subject...

  4. Handbook of nuclear ships

    International Nuclear Information System (INIS)

    1981-03-01

    First, the government organs and other organizations related to nuclear ships and their tasks are described. The fundamental plan for the development of nuclear ships had been determined in July, 1963, and was revised three times thereafter. However in December, 1980, new determination to carry out the research works also was made. The course of the construction of the nuclear ship ''Mutsu'' from 1955 to 1980, the main particulars of the nuclear ship ''Mutsu'' and the drawing of the general arrangement are shown. The designated port for berthing the Mutsu was completed in 1972 in Ominato, Aomori Prefecture, but after the happening of radiation leak during the trial operation of the Mutsu in 1974, it was agreed to remove the port. The main works to be carried out at the port and the port facilities are explained. The progress of the examination of safety of the Mutsu and the result, the test of raising the power output carried out in 1974, and the course of selecting the port for making the repair works of the Mutsu are described. The law concerning Japan Nuclear Ship Research and Development Agency had been instituted in 1963, and was revised four times thereafter. The change of the budget for the tests and researches related to nuclear ships in Japan is shown. The state of development of nuclear ships in foreign countries, the international organs related to atomic energy, shipping, shipbuilding and energy, and chronological table are introduced. (Kako, I.)

  5. Effective and Safe Ships

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup; Amdahl, Jørgen; Rutgersson, Olle

    1996-01-01

    A Joint Nordic Research project "Effecive and Safe Ships" is presented. The project is aiming to develop methods and tools for quantitative evaluation fo ship safety. This report is the report of the preliminary phase where the plan for the main project is developed. The objectives of the project...

  6. Biofibres from biofuel industrial byproduct-Pongamia pinnata seed hull.

    Science.gov (United States)

    Manjula, Puttaswamy; Srinikethan, Govindan; Shetty, K Vidya

    2017-01-01

    Biodiesel production using Pongamia pinnata (P. pinnata) seeds results in large amount of unused seed hull. These seed hulls serve as a potential source for cellulose fibres which can be exploited as reinforcement in composites. These seed hulls were processed using chlorination and alkaline extraction process in order to isolate cellulose fibres. Scanning electron microscopy (SEM), dynamic light scattering (DLS), thermogravimetric analysis (TGA), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance spectroscopy (NMR) analysis demonstrated the morphological changes in the fibre structure. Cellulose microfibres of diameter 6-8 µm, hydrodynamic diameter of 58.4 nm and length of 535 nm were isolated. Thermal stability was enhanced by 70 °C and crystallinity index (CI) by 19.8% ensuring isolation of crystalline cellulose fibres. The sequential chlorination and alkaline treatment stemmed to the isolation of cellulose fibres from P. pinnata seed hull. The isolated cellulose fibres possessed enhanced morphological, thermal, and crystalline properties in comparison with P. pinnata seed hull. These cellulose microfibres may potentially find application as biofillers in biodegradable composites by augmenting their properties.

  7. Region-of-interest volumetric visual hull refinement

    KAUST Repository

    Knoblauch, Daniel

    2010-01-01

    This paper introduces a region-of-interest visual hull refinement technique, based on flexible voxel grids for volumetric visual hull reconstructions. Region-of-interest refinement is based on a multipass process, beginning with a focussed visual hull reconstruction, resulting in a first 3D approximation of the target, followed by a region-of-interest estimation, tasked with identifying features of interest, which in turn are used to locally refine the voxel grid and extract a higher-resolution surface representation for those regions. This approach is illustrated for the reconstruction of avatars for use in tele-immersion environments, where head and hand regions are of higher interest. To allow reproducability and direct comparison a publicly available data set for human visual hull reconstruction is used. This paper shows that region-of-interest reconstruction of the target is faster and visually comparable to higher resolution focused visual hull reconstructions. This approach reduces the amount of data generated through the reconstruction, allowing faster post processing, as rendering or networking of the surface voxels. Reconstruction speeds support smooth interactions between the avatar and the virtual environment, while the improved resolution of its facial region and hands creates a higher-degree of immersion and potentially impacts the perception of body language, facial expressions and eye-to-eye contact. Copyright © 2010 by the Association for Computing Machinery, Inc.

  8. Shipping Information Pipeline

    DEFF Research Database (Denmark)

    Jensen, Thomas

    to creating a more efficient shipping industry, and a number of critical issues are identified. These include that shipments depend on shipping information, that shipments often are delayed due to issues with documentation, that EDI messages account for only a minor part of the needed information......This thesis applies theoretical perspectives from the Information Systems (IS) research field to propose how Information Technology (IT) can improve containerized shipping. This question is addressed by developing a set of design principles for an information infrastructure for sharing shipping...... information named the Shipping Information Pipeline (SIP). Review of the literature revealed that IS research prescribed a set of meta-design principles, including digitalization and digital collaboration by implementation of Inter-Organizational Systems based on Electronic Data Interchange (EDI) messages...

  9. Analysis of Methods of Determining the Safe Ship Trajectory

    Directory of Open Access Journals (Sweden)

    Jozef Lisowski

    2016-07-01

    Full Text Available The paper describes six methods of optimal and game theory and artificial neural network for synthesis of safe control in collision situations at sea. The application of optimal and game control algorithms to determine the own ship safe trajectory during the passing of other encountered ships in good and restricted visibility at sea is presented. The comparison of the safe ship control in collision situation: multi-step matrix non-cooperative and cooperative games, multi-stage positional non-cooperative and cooperative games have been introduced. The considerations have been illustrated with examples of computer simulation of the algorithms to determine safe of own ship trajectories in a navigational situation during passing of eight met ships.

  10. Game Strategies of Ship in the Collision Situations

    Directory of Open Access Journals (Sweden)

    Jozef Lisowski

    2014-03-01

    Full Text Available The paper introduced the basic model of process of safe ship control in a collision situation using a game model with j objects, which includes non-linear state equations and non-linear, time varying constraints of the state variables as well as the quality game control index in the forms of the game integral payment and the final payment. Approximated model of the process control as the model of multi-step matrix game in the form of dual linear programming problem has been adopted here. The Game Ship Control GSC computer program has been designed in the Matlab/Simulink software in order to determine the own ship's safe trajectory. These considerations have been illustrated with examples of a computer simulation using an GSC program for determining the safe ship's trajectory in real navigational situation. Simulation research were passed for five sets of strategies of the own ship and met ships.

  11. The role of hull in germination and salinity tolerance in some ...

    African Journals Online (AJOL)

    hulled and dehulled) of sunflower seeds of Opal, Shelly (Confectionary) and Pactol (Oily) were tested to determine the effects of the hull on salinity tolerance during germination. Germination percentage (%), mean germination time (day), root and ...

  12. Calculation of the collision resistance of ships and its assessment for classification purposes

    International Nuclear Information System (INIS)

    Boeckenhauer, M.; Egge, E.D.

    1994-01-01

    Within the framework of a research programme ''Tanker Safety'', Germanischer Lloyd has developed a program system for the evaluation of the absorbed plastic deformation energy in a ship-ship collision. The ultimate load capacities of the ship structures in the areas affected by the collision are evaluated stepwise. The total collision energy absorbed by plastic deformations of the ship structures is evaluated on the basis of the minima of the ultimate load capacities and the corresponding penetration depths. By means of the collision energy absorbed, the collision speed necessary to cause damage can be determined.It is now possible to classify ships with regard to their resistance against collisions and to assign relevant class notations.The resistance of a ship against collision impacts is expressed by the class notation COLL with index numbers ranging from 1 to 6. The index numbers indicate that - as compared with a non-strengthened single hull reference ship - a critical situation is likely to occur only if the deformation energy absorbed in the collision exceeds that of the non-strengthened reference ship by specified values.A ''critical situation'' is defined by, for example, rupture of cargo tanks with subsequent spillage of cargo or water ingress into dry cargo holds. ((orig.))

  13. ISOLATION AND CHARACTERIZATION OF NANOFIBRILLATED CELLULOSE FROM OAT HULLS

    Directory of Open Access Journals (Sweden)

    Giovanni B. Paschoal

    2015-05-01

    Full Text Available The objectives of this work were to investigate the microstructure, crystallinity and thermal stability of nanofibrillated cellulose obtained from oat hulls using bleaching and acid hydrolysis at a mild temperature (45 ºC followed by ultrasonication. The oat hulls were bleached with peracetic acid, and after bleaching, the compact structure around the cellulosic fibers was removed, and the bundles became individualized. The extraction time (30 or 60 min did not affect the properties of the nanofibrillated cellulose, which presented a higher crystallinity index and thermal stability than the raw material (oat hulls. The nanocellulose formed interconnected webs of tiny fibers with diameters of 70-100 nm and lengths of several micrometers, producing nanofibers with a relatively high aspect ratio, thus indicating that these materials are suitable for polymer reinforcement.

  14. Yeast hulls: effect on spontaneous fermentation in different vinification conditions

    Directory of Open Access Journals (Sweden)

    Rosa López

    2000-09-01

    Full Text Available The effect of the addition of yeast hulls in vinification was investigated during three consecutive years. The study was carried out in the experimental winery of C.I.D.A in La Rioja (Spain with free running white grape juice of the Viura variety. Four different vinifications were studied. In two of these vinifications, stuck fermentations were detected. In all the studies, the addition of yeast hulls (yeast ghosts improved the fermentation kinetics, increasing the number of viable yeasts at the end of the exponential stage and decreasing the final content of reducing sugars. This work revealed a new effect of yeast hull addition which had not been identified previously; their selection effect on the wild yeast strain in spontaneous fermentation.

  15. Trends in oil spills from tanker ships 1995-2004

    International Nuclear Information System (INIS)

    Huijer, K.

    2005-01-01

    The trends in oil spills around the world over from 1995 to 2004 were examined and analyzed for possible influences on spill volumes and frequencies for incidents of 3 spill size classes. The International Tanker Owners Pollution Federation (ITOPF) has maintained a database since 1974 of all oil spills from tankers, combined carriers and barges. The number of oil spills has decreased significantly in the last 30 years despite a steady increase in maritime oil trade since the 1980s. The recent trends were identified by causes, locations, oil type, and shipping legislation. The causes include ship loading/discharging, bunkering, collisions, groundings, hull failures and fires. The types of oil spilt include bunker, crude, cargo fuel, white product and some unknowns. It was concluded that the decline in oil spills is due to a range of initiatives taken by governments and the shipping industry rather than any one factor. Some notable influences towards reduced number of spills include: the international convention for the prevention of pollution from ships of 1972, as modified by the Protocol of 1978; the international convention for the safety of life at sea of 1974; and the Oil Pollution Act of 1990. Results of investigations into the causes of spills serve the purpose of informing the international process to further prevent and reduce marine oil pollution due to tankers. 7 refs., 5 tabs., 12 figs

  16. Performance of Ships and Offshore Structures in Waves

    Directory of Open Access Journals (Sweden)

    Shukui Liu

    2012-01-01

    for predicting large amplitude motions of ships and floating structures in response to incoming waves in the frame of potential theory. The developed alternative set of time domain methods simulate the hydrodynamic forces acting on ships advancing in waves with constant speed. For motions’ simulation, the diffraction forces and radiation forces are calculated up to the mean wetted surface, while the Froude-Krylov forces and hydrostatic restoring forces are calculated up to the undisturbed incident wave surface in case of large incident wave amplitude. This enables the study of the above waterline hull form effect. Characteristic case studies on simulating the hydrodynamic forces and motions of standard type of ships have been conducted for validation purpose. Good agreement with other numerical codes and experimental data has been observed. Furthermore, the added resistance of ships in waves can be calculated by the presented methods. This capability supports the increased demand of this type of tools for the proper selection of engine/propulsion systems accounting for ship’s performance in realistic sea conditions, or when optimizing ship’s sailing route for minimum fuel consumption and toxic gas emissions.

  17. Convex Hull Abstraction in Specialisation of CLP Programs

    DEFF Research Database (Denmark)

    Peralta, J.C.; Gallagher, John Patrick

    2003-01-01

    We introduce an abstract domain consisting of atomic formulas constrained by linear arithmetic constraints (or convex hulls). This domain is used in an algorithm for specialization of constraint logic programs. The algorithm incorporates in a single phase both top-down goal directed propagation...... and bottom-up answer propagation, and uses a widening on the convex hull domain to ensure termination. We give examples to show the precision gained by this approach over other methods in the literature for specializing constraint logic programs. The specialization method can also be used for ordinary logic...

  18. Drag Reduction trough Special paints Coated on the hull

    OpenAIRE

    Izaguirre Alza, Patricia; Pérez Rojas, Luis; Núñez Basáñez, José Fernando

    2010-01-01

    The economic recession, the environmental impact as well as the continuous fossil fuel consumption encourage actions that focus on saving energy. In the vessels sector, one of the main objectives has always been to reach a hydro-dynamically optimum hull which gave the desired speed with minimum power. Hydrodynamic drag is basically divided into two parts: a) the friction between the water and the hull, and b) the wave generation due to the free-surface air-water. Presented in this paper...

  19. Heat-treated hull flour does not affect iron bioavailability in rats.

    Science.gov (United States)

    Martino, Hércia Stampini Duarte; Carvalho, Ariela Werneck de; Silva, Cassiano Oliveira da; Dantas, Maria Inês de Souza; Natal, Dorina Isabel Gomes; Ribeiro, Sônia Machado Rocha; Costa, Neuza Maria Brunoro

    2011-06-01

    In this study the chemical composition and iron bioavailability of hull and hull-less soybean flour from the new cultivar UFVTN 105AP was evaluated. The hemoglobin depletion-repletion method was used in Wistar rats. Soybean hull flour presented 37% more total dietary fiber and higher content of iron than hull-less soybean flour. The phytate:iron molar ratio, however, was 2-fold lower in the soybean hull flour in compared to the hull-less soybean flour. Animals fed soybean hull flour presented hemoglobin gains similar to those of the control diet group (p > 0.05). The Relative Biological Values of hull and hull-less soybean flour were 68.5% and 67.1%, respectively, compared to the control group. Heat-treated soybean hull flour (150 degrees C/30 minutes) showed high content of iron and low phytate, which favors the iron bioavailability. Thus, the soybean hull flour is a better source of dietary fiber and iron than hull-less soybean flour at comparable bioavailabilities.

  20. 14 CFR 25.533 - Hull and main float bottom pressures.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float bottom pressures. 25... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.533 Hull and main float bottom pressures. (a) General. The hull and main float structure, including frames and bulkheads...

  1. 14 CFR 23.529 - Hull and main float landing conditions.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float landing conditions. 23... Water Loads § 23.529 Hull and main float landing conditions. (a) Symmetrical step, bow, and stern... directed perpendicularly to the keel line. (b) Unsymmetrical landing for hull and single float seaplanes...

  2. 14 CFR 23.531 - Hull and main float takeoff condition.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float takeoff condition. 23.531 Section 23.531 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... Water Loads § 23.531 Hull and main float takeoff condition. For the wing and its attachment to the hull...

  3. Of Curriculum Conceptions, Orientations, and Cultures: A Rejoinder to John E. Hull

    Science.gov (United States)

    Van Brummelen, Harro

    2009-01-01

    In this article, the author presents a rejoinder to John E. Hull. Van Brummelen first states his appreciation of John Hull's thoughtful evaluation of his views of curriculum, views in which many Christian educators have played a part. It has been several decades since the author spelled out what Hull calls an "education for discipleship"…

  4. 33 CFR 80.135 - Hull, MA to Race Point, MA.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Hull, MA to Race Point, MA. 80... INTERNATIONAL NAVIGATION RULES COLREGS DEMARCATION LINES Atlantic Coast § 80.135 Hull, MA to Race Point, MA. (a... the east coast of Massachusetts from the easternmost radio tower at Hull, charted in approximate...

  5. 14 CFR 25.527 - Hull and main float load factors.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float load factors. 25.527... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.527 Hull and main... 1=empirical hull station weighing factor, in accordance with figure 2 of appendix B. (7) r x=ratio...

  6. 33 CFR Appendix G to Part 157 - Timetables for Application of Double Hull Requirements

    Science.gov (United States)

    2010-07-01

    ... Double Hull Requirements G Appendix G to Part 157 Navigation and Navigable Waters COAST GUARD, DEPARTMENT... Application of Double Hull Requirements 1. Source. These timetables conform to 46 U.S.C. 3703a(c). 2... double hull or with a double containment system determined by the Coast Guard to be as effective as a...

  7. 14 CFR 23.527 - Hull and main float load factors.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float load factors. 23.527... Water Loads § 23.527 Hull and main float load factors. (a) Water reaction load factors nw must be...=seaplane landing weight in pounds. (6) K1=empirical hull station weighing factor, in accordance with figure...

  8. 33 CFR 181.27 - Information displayed near hull identification number.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Information displayed near hull... displayed near hull identification number. With the exception of the characters “US-”, which constitute the... the 12-character hull identification number (HIN), that information must be separated from the HIN by...

  9. 14 CFR 25.529 - Hull and main float landing conditions.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float landing conditions. 25... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.529 Hull and main.... (b) Unsymmetrical landing for hull and single float seaplanes. Unsymmetrical step, bow, and stern...

  10. 78 FR 50335 - Double Hull Tanker Escorts on the Waters of Prince William Sound, Alaska

    Science.gov (United States)

    2013-08-19

    ...-AB96 Double Hull Tanker Escorts on the Waters of Prince William Sound, Alaska AGENCY: Coast Guard, DHS... mandates two tug escorts for double hull tankers over 5,000 gross tons transporting oil in bulk in PWS. The... tug escort requirements apply to certain double hull tankers. DATES: This interim rule is effective...

  11. 14 CFR 25.531 - Hull and main float takeoff condition.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float takeoff condition. 25... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.531 Hull and main float takeoff condition. For the wing and its attachment to the hull or main float— (a) The aerodynamic...

  12. 77 FR 29251 - Safety Zone; Carnival Fireworks Display, Nantasket Beach, Hull, MA

    Science.gov (United States)

    2012-05-17

    ...-AA00 Safety Zone; Carnival Fireworks Display, Nantasket Beach, Hull, MA AGENCY: Coast Guard, DHS... zone on the navigable waters off of Nantasket Beach in the vicinity of Hull, MA for a Carnival... spectators and vessels from the hazards associated with fireworks displays. Discussion of Proposed Rule Hull...

  13. 7 CFR 319.8-9 - Hull fiber and gin trash.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 5 2010-01-01 2010-01-01 false Hull fiber and gin trash. 319.8-9 Section 319.8-9 Agriculture Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION... Importation and Entry of Cotton and Covers § 319.8-9 Hull fiber and gin trash. (a) Entry of hull fiber will be...

  14. Management of waste cladding hulls. Part II. An assessment of zirconium pyrophoricity and recommendations for handling waste hulls

    International Nuclear Information System (INIS)

    Kullen, B.J.; Levitz, N.M.; Steindler, M.J.

    1977-11-01

    This report reviews experience and research related to the pyrophoricity of zirconium and zirconium alloys. The results of recent investigations of the behavior of Zircaloy and some observations of industrial handling and treatment of Zircaloy tubing and scrap are also discussed. A model for the management of waste Zircaloy cladding hulls from light water reactor fuel reprocessing is offered, based on an evaluation of the reviewed information. It is concluded that waste Zircaloy cladding hulls do not constitute a pyrophoric hazard if, following the model flow sheet, finely divided metal is oxidized during the management procedure. Steps alternative to the model are described which yield zirconium in deactivated form and also accomplish varying degrees of transuranic decontamination. Information collected into appendixes is (1) a collation of zirconium pyrophoricity data from the literature, (2) calculated radioactivity contents in Zircaloy cladding hulls from spent LWR fuels, and (3) results of a laboratory study on volatilization of zirconium from Zircaloy using HCl or Cl 2

  15. Designing Adaptable Ships: Modularity and Flexibility in Future Ship Designs

    Science.gov (United States)

    2016-01-01

    with motors, belts, shafts , seals, valves, hose spindles , and switches. If ship installation is not installed, the system will be status quo. Ship...Impact: the current centrifugal purifiers (Alfa-Laval) have experienced frequent failures with motor, belts, shafts , seals, valves, hose spindles ... Designing Adaptable Ships Modularity and Flexibility in Future Ship Designs John F. Schank, Scott Savitz, Ken Munson, Brian Perkinson, James

  16. Optimization in liner shipping

    DEFF Research Database (Denmark)

    Brouer, Berit Dangaard; Karsten, Christian Vad; Pisinger, David

    2017-01-01

    Seaborne trade is the lynchpin in almost every international supply chain, and about 90% of non-bulk cargo worldwide is transported by container. In this survey we give an overview of data-driven optimization problems in liner shipping. Research in liner shipping is motivated by a need for handling...... still more complex decision problems, based on big data sets and going across several organizational entities. Moreover, liner shipping optimization problems are pushing the limits of optimization methods, creating a new breeding ground for advanced modelling and solution methods. Starting from liner...... shipping network design, we consider the problem of container routing and speed optimization. Next, we consider empty container repositioning and stowage planning as well as disruption management. In addition, the problem of bunker purchasing is considered in depth. In each section we give a clear problem...

  17. Civilian nuclear ships

    International Nuclear Information System (INIS)

    Oelgaard, P.L.

    1993-03-01

    This report contains a review of the information available on nuclear powered ships, built for civilian purposes. In the introduction a short discussion is given of the reasons for the limited use of nuclear ships for these purposes. In the second section a brief review is presented of data for the three experimental/merchant ships build by the United States, Germany and Japan, i.e. NS Savannah, NS Otto Hahn and NS Mutsu. In the third section the Soviet/Russian icebreaker NS Lenin is considered. Its design, operational experience and the introduction of a new nuclear propulsion plant is reviewed. In the fourth section the newer Soviet/Russian icebreakers with nuclear propulsion are considered. Finally design of the Soviet/Russian icebreaker transport/container ship NS Sevmorput is reviewed in the fifth section. The future Russian plans for nuclear vessels for the arctic waters are briefly discussed. (au)

  18. Ship propulsion reactors technology

    International Nuclear Information System (INIS)

    Fribourg, Ch.

    2002-01-01

    This paper takes the state of the art on ship propulsion reactors technology. The french research programs with the corresponding technological stakes, the reactors specifications and advantages are detailed. (A.L.B.)

  19. Ship construction and welding

    CERN Document Server

    Mandal, Nisith R

    2017-01-01

    This book addresses various aspects of ship construction, from ship types and construction materials, to welding technologies and accuracy control. The contents of the book are logically organized and divided into twenty-one chapters. The book covers structural arrangement with longitudinal and transverse framing systems based on the service load, and explains basic structural elements like hatch side girders, hatch end beams, stringers, etc. along with structural subassemblies like floors, bulkheads, inner bottom, decks and shells. It presents in detail double bottom construction, wing tanks & duct keels, fore & aft end structures, etc., together with necessary illustrations. The midship sections of various ship types are introduced, together with structural continuity and alignment in ship structures. With regard to construction materials, the book discusses steel, aluminum alloys and fiber reinforced composites. Various methods of steel material preparation are discussed, and plate cutting and form...

  20. Nuclear ship accidents

    International Nuclear Information System (INIS)

    Oelgaard, P.L.

    1993-05-01

    In this report available information on 28 nuclear ship accident and incidents is considered. Of these 5 deals with U.S. ships and 23 with USSR ships. The ships are in almost all cases nuclear submarines. Only events that involve the nuclear propulsion plants, radiation exposures, fires/explosions and sea water leaks into the submarines are considered. Comments are made on each of the events, and at the end of the report an attempt is made to point out the weaknesses of the submarine designs which have resulted in the accidents. It is emphasized that much of the available information is of a rather dubious nature. consequently some of the assessments made may not be correct. (au)

  1. Distributed propulsion for ships

    OpenAIRE

    Nylund, Vilde

    2017-01-01

    It is anticipated that using distributed electric propulsion (DEP) on conventional ships will increase the total propulsive efficiency. This is mainly due to two reasons; firstly, because the total propeller disk area can be increased. Secondly, because each propeller can be optimised for the local wake where it is operating. In this work, the benefits of using DEP has been investigated for a 14 000 TEU container ship. Based on a literary study of the present state of propeller modelling ...

  2. SHIPPING REQUESTS ON EDH

    CERN Multimedia

    Logistics Group

    2001-01-01

    Users are informed that as from 1 September 2001 all Shipping Requests must be made on EDH using the appropriate electronic form. The submission of user requests directly into EDH will help rationalise the activities of the Shipping Service (Import & Export), with requests being automatically forwarded to hierarchical supervisors thereby improving the processing speed and facilitating the follow-up. Thank you for your collaboration.

  3. Plastic Pollution from Ships

    OpenAIRE

    Čulin, Jelena; Bielić, Toni

    2016-01-01

    The environmental impact of shipping on marine environment includes discharge of garbage. Plastic litter is of particular concern due to abundance, resistance to degradation and detrimental effect on marine biota. According to recently published studies, a further research is required to assess human health risk. Monitoring data indicate that despite banning plastic disposal at sea, shipping is still a source of plastic pollution. Some of the measures to combat the problem are discussed.

  4. Hydroelastic response of 19,000 TEU class ultra large container ship with novel mobile deckhouse for maximizing cargo capacity

    Directory of Open Access Journals (Sweden)

    Hong-Il Im

    2017-05-01

    Full Text Available This paper is related to structural design evaluation of 19,000 TEU ultra large container ship, dealing with hydroelastic response, i.e. springing and whipping. It illustrates application of direct calculation tools and methodologies to both fatigue and ultimate strength assessment, simultaneously taking into account ship motions and her elastic deformations. Methodology for springing and whipping assessment within so called WhiSp notation is elaborated in details, and in order to evaluate innovative container ship design with increased loading capacity, a series of independent hydroelastic computations for container ship with mobile deckhouse and conventional one are performed with the same calculation setup. Fully coupled 3D FEM – 3D BEM model is applied, while the ultimate bending capacity of hull girder is determined by means of MARS software. Beside comparative analysis of representative quantities for considered ships, relative influence of hydroelasticity on ship response is addressed.

  5. Analysis of ship maneuvering data from simulators

    Science.gov (United States)

    Frette, V.; Kleppe, G.; Christensen, K.

    2011-03-01

    We analyze complex manuevering histories of ships obtained from training sessions on bridge simulators. Advanced ships are used in fields like offshore oil exploration: dive support vessels, supply vessels, anchor handling vessels, tugs, cable layers, and multi-purpose vessels. Due to high demands from the operations carried out, these ships need to have very high maneuverability. This is achieved through a propulsion system with several thrusters, water jets, and rudders in addition to standard propellers. For some operations, like subsea maintenance, it is crucial that the ship accurately keeps a fixed position. Therefore, bridge systems usually incorporate equipment for Dynamic Positioning (DP). DP is a method to keep ships and semi submersible rigs in a fixed position using the propulsion systems instead of anchors. It may also be used for sailing a vessel from one position to another along a predefined route. Like an autopilot on an airplane, DP may operate without human involvement. The method relies on accurate determination of position from external reference systems like GPS, as well as a continuously adjusted mathematical model of the ship and external forces from wind, waves and currents. In a specific simulator exercise for offshore crews, a ship is to be taken up to an installation consisting of three nearby oil platforms connected by bridges (Frigg field, North Sea), where a subsea inspection is to be carried out. Due to the many degrees of freedom during maneuvering, including partly or full use of DP, the chosen routes vary significantly. In this poster we report preliminary results on representations of the complex maneuvering histories; representations that allow comparison between crew groups, and, possibly, sorting of the different strategic choices behind.

  6. The Hull Method for Selecting the Number of Common Factors

    Science.gov (United States)

    Lorenzo-Seva, Urbano; Timmerman, Marieke E.; Kiers, Henk A. L.

    2011-01-01

    A common problem in exploratory factor analysis is how many factors need to be extracted from a particular data set. We propose a new method for selecting the number of major common factors: the Hull method, which aims to find a model with an optimal balance between model fit and number of parameters. We examine the performance of the method in an…

  7. "Keisri hull" pürib taas filmiks

    Index Scriptorium Estoniae

    2008-01-01

    Eesti Filmi Sihtasutus otsustas anda arendustoetust mängufilmidele "Keisri hull" (režissöör Peeter Simm, arendaja Lege Artis Film), "Rahad ette" (režissöör Jaak Kilmi, arendaja Eetriüksus), "Öölendurid" (režissöör Peeter Urbla, arendaja Exitfilm)

  8. Water Pressure Distribution on a Flying Boat Hull

    Science.gov (United States)

    Thompson, F L

    1931-01-01

    This is the third in a series of investigations of the water pressures on seaplane floats and hulls, and completes the present program. It consisted of determining the water pressures and accelerations on a Curtiss H-16 flying boat during landing and taxiing maneuvers in smooth and rough water.

  9. Hybrid Wireless Hull Monitoring System for Naval Combat Vessels

    Science.gov (United States)

    2010-03-01

    Payload Data Acquisition System (SPDAS) is designed by the Technology Management Group, Inc. ( TMG ). In its design, the monitoring system is intended...monitoring system custom designed by TMG for the U.S. Navy. The Scientific Payload Data Acquisition System (SPDAS) is a wired hull monitoring system

  10. Leaching behavior of water-soluble carbohydrates from almond hulls

    Science.gov (United States)

    Over 58% of the dry matter content of the hulls from the commercial almond (Prunus dulcis (Miller) D.A. Webb) is soluble in warm water (50-70°C) extraction. The water-soluble extractables include useful amounts of fermentable sugars (glucose, fructose, sucrose), sugar alcohols (inositol and sorbito...

  11. PAUT-based defect detection method for submarine pressure hulls

    Directory of Open Access Journals (Sweden)

    Min-jae Jung

    2018-03-01

    Full Text Available A submarine has a pressure hull that can withstand high hydraulic pressure and therefore, requires the use of highly advanced shipbuilding technology. When producing a pressure hull, periodic inspection, repair, and maintenance are conducted to maintain its soundness. Of the maintenance methods, Non-Destructive Testing (NDT is the most effective, because it does not damage the target but sustains its original form and function while inspecting internal and external defects. The NDT process to detect defects in the welded parts of the submarine is applied through Magnetic particle Testing (MT to detect surface defects and Ultrasonic Testing (UT and Radiography Testing (RT to detect internal defects. In comparison with RT, UT encounters difficulties in distinguishing the types of defects, can yield different results depending on the skills of the inspector, and stores no inspection record. At the same time, the use of RT gives rise to issues related to worker safety due to radiation exposure. RT is also difficult to apply from the perspectives of the manufacturing of the submarine and economic feasibility. Therefore, in this study, the Phased Array Ultrasonic Testing (PAUT method was applied to propose an inspection method that can address the above disadvantages by designing a probe to enhance the precision of detection of hull defects and the reliability of calculations of defect size. Keywords: Submarine pressure hull, Non-destructive testing, Phased array ultrasonic testing

  12. Production of furfural and ethyl alcohol from cottonseed hulls

    Energy Technology Data Exchange (ETDEWEB)

    Bobovnikov, B M; Tsirlin, Yu A; Chepigo, S V; Shpuntova, M E

    1957-01-01

    Cottonseed hulls (8.3 tons per digester) and H/sub 2/SO/sub 4/ solution at temperature of 100/sup 0/ were added to the digester simultaneously. The final H/sub 2/SO/sub 4/ concentration of the charge was approximately 0.7%. The pentosans were hydrolyzed at 133/sup 0/ and 2 atmosphere for 6 hours and 15 minutes, then the temperature was raised to 179/sup 0/ at the top and to 150/sup 0/ at the bottom of the digester for 5 hours and 30 minutes. The hydrolytic products of pentosan were separated, neutralized, and transferred to a dehydration tank. The hexosans were then hydrolyzed at 179 to 187/sup 0/. Dry hulls gave 19.4% of pentose reducing sugars, of which 81.4% were fermented. One ton of dry hulls gave 74 to 79 l. of ethanol. The optimum condition for dehydration was at 165 to 175/sup 0/ for no longer than 4 to 4.5 hours. 2-Furaldehyde was produced in the following steps: the pentosan hydrolyzate was dehydrated with steam, the vapor-furaldehyde mixture was then reheated and finally distilled in a continuous column. The yield of furaldehyde was 36 to 37% of incoming pentoses (7% of dry hulls).

  13. Outer Dynamics of Ship Collisions

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup

    1996-01-01

    The purpose is to present analysis procedures for the motion of ships during ship-ship collisions and for ship collisions with offshore structures. The aim is to estimate that part of the lost kinetic energy which will have to be absorbed by rupture and plastic damage of the colliding structures....

  14. Recent situations around nuclear ships

    International Nuclear Information System (INIS)

    Mizuno, Hiroshi

    1978-01-01

    The philosophy when the safety standard for nuclear ships is drawn up and the international rules specifically for nuclear ships are summarized. As for the safety standard for nuclear ships, the safety requirements for ordinary ships, for the ships transporting nuclear reactors, for ordinary nuclear reactors, and for the reactors moving around the seas must be included. As for the international rules for nuclear ships, there are chapter 8 ''Nuclear ships'' in the International Convention on the Safety of Life at Sea, 1960 and 1974, and Safety Consideration in the Use of Ports and Approaches by Nuclear Merchant Ships. Also there are national rules and standards in Japan and foreign countries. One of the means to explore the practicality of nuclear ships is the investigation of the economy. At this time, the social merits and demerits of nuclear ships must be compared with conventional ships by taking total expenses into account without omission. When oil is depleted, the age of nuclear ships will not necessarily begin, and the will be still some competitors. The investigations concerning the economy of nuclear ships have been carried out in various countries. The present state of the development of nuclear ships in Japan and foreign countries is explained. Many conferences and symposia have been held concerning nuclear ships, and those held recently are enumerated. The realization of nuclear ship age cannot be anticipated from existing papers and shipbuilding projects. (Kako, I.)

  15. Outer Dynamics of Ship Collisions

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup

    1996-01-01

    The purpose of these notes is to present analysis procedures for the motion of ships during ship-ship collisions and for ship collisons with offshore structures. The aim is to estimate that part of the lost kinetic energy which will have to be absorbed by rupture and plastic damage of the colliding...

  16. Full scale leak test of the MEGAPIE containment hull

    Energy Technology Data Exchange (ETDEWEB)

    Samec, K

    2006-07-15

    The Full Scale Leak Test (FSLT) experiment is designed to replicate an accidental leak of Lead-Bismuth Eutectic (LBE) liquid metal from the MEGAPIE neutron spallation source. The neutron source is totally encased in an aluminum containment hull cooled by heavy water. Any liquid metal which would, in a hypothetical accident, leak into the helium-filled insulation gap between the source and the aluminum containment hull, would immediately impact the hull. Furthermore, during irradiation in the PSI SINQ facility, the LBE in the MEGAPIE Lower Liquid Metal Container (LLMC) accumulates radio-active substances which, in the event of a leak, must be cooled and contained under controlled conditions, as they may otherwise contaminate the facility. The FSLT experiment has been devised to fully test the structural integrity of the containment hull against a sudden liquid metal leak, and in addition, to resolve the peak temperature of he coolant, to validate the sensors used in detecting a leak and of proof-test the analytical methods used in predicting the consequences of a leak. The FSLT experiment has been analysed ahead of the test, and both thermal and structural aspects calculated using commercial codes. The predictions applied conservative assumptions to the analysis of the thermal shock so as to preclude the likelihood of an unforeseen failure of the hull. In this document, these initial predictions are compared to the temperature and strain data recorded in the experiment. Further analysis, to be published at a later stage, will focus on applying actual conditions realised in the experiment, as opposed to the envelope case used in the test predictions. The integrity of the containment hull under loads resulting from liquid metal-leak is therefore the focal point of the experiment described in the current document, and serves as a key reference test for the Iicensing of the facility. The data recorded during the SLT experiment shows that the MEGAPIE containment hull is

  17. Full scale leak test of the MEGAPIE containment hull

    International Nuclear Information System (INIS)

    Samec, K.

    2006-07-01

    The Full Scale Leak Test (FSLT) experiment is designed to replicate an accidental leak of Lead-Bismuth Eutectic (LBE) liquid metal from the MEGAPIE neutron spallation source. The neutron source is totally encased in an aluminum containment hull cooled by heavy water. Any liquid metal which would, in a hypothetical accident, leak into the helium-filled insulation gap between the source and the aluminum containment hull, would immediately impact the hull. Furthermore, during irradiation in the PSI SINQ facility, the LBE in the MEGAPIE Lower Liquid Metal Container (LLMC) accumulates radio-active substances which, in the event of a leak, must be cooled and contained under controlled conditions, as they may otherwise contaminate the facility. The FSLT experiment has been devised to fully test the structural integrity of the containment hull against a sudden liquid metal leak, and in addition, to resolve the peak temperature of he coolant, to validate the sensors used in detecting a leak and of proof-test the analytical methods used in predicting the consequences of a leak. The FSLT experiment has been analysed ahead of the test, and both thermal and structural aspects calculated using commercial codes. The predictions applied conservative assumptions to the analysis of the thermal shock so as to preclude the likelihood of an unforeseen failure of the hull. In this document, these initial predictions are compared to the temperature and strain data recorded in the experiment. Further analysis, to be published at a later stage, will focus on applying actual conditions realised in the experiment, as opposed to the envelope case used in the test predictions. The integrity of the containment hull under loads resulting from liquid metal-leak is therefore the focal point of the experiment described in the current document, and serves as a key reference test for the Iicensing of the facility. The data recorded during the SLT experiment shows that the MEGAPIE containment hull is

  18. Measurement of dose rate and estimation of beta activity in zircaloy hull drum

    International Nuclear Information System (INIS)

    Pandey, J.P.N.; Kumar, Pankaj; Shinde, A.M.; Purohit, R.G.; Sarkar, P.K.

    2012-01-01

    Fuel Reprocessing Plant is designed for the processing of spent fuel from reactor for the recovery of plutonium and uranium as PuO 2 and U 3 O 8 respectively. Zircaloy is used as cladding material of natural uranium fuel pins used in the reactors. In reprocessing plants chop and leach method is used to remove the zircaloy clad from the fuel matrix during Head End Treatment. Initially spent fuel bundles are chopped into pieces and collected in perforated baskets kept in dissolvers. All chopped pieces are dissolved in HNO 3 in the dissolvers followed by heating and boiling. Dissolved solutions are transferred to Filtrate Tank (FT) leaving behind un-dissolved zircoloy hull pieces in the dissolver baskets. Un-dissolved and almost dry hull pieces are transferred in hull drum from the dissolver baskets using the Hull Tilting Facility. Hull drums are made of stainless steel having 500 litre capacity and two third of its volume is filled with zircoloy pieces. Hull drums filled with hull pieces are loaded in Hull Removal Cask (HRC) and transported to SWMF (Solid Waste Management Facility) site for interim storage/disposal in tile holes. Hull pieces are high active solid wastes which contain significant amount of fission products. Radiation levels on hull drums are in the range of few hundreds of mGy/h which has high potential of external hazards if not handled properly. Therefore hull drums are handled remotely in specially designed lead shielded cask

  19. How propeller suction is the dominant factor for ship accidents at shallow water conditions

    Science.gov (United States)

    Acar, Dursun; Alpar, Bedri; Ozeren, Sinan

    2017-04-01

    The laminar flow comes to the fore with the disappearance of the several other directions in the internal displacements in the water current. Due to the dominant speed direction during the straightforward motion of the ship, the underwater hull is associated with the continuous flow of laminar currents. The open marine environment acts as a compressible liquid medium because of the presence of many variables about water volume overflow boundaries where the ship is associated. Layers of water rising over the sea surface due to ship's body and the propeller's water push provides loss of liquid lifting force for the ship. These situations change the well-known sea-floor morphology and reliable depth limits, and lead to probable accidents. If the ship block coefficient for the front side is 0.7 or higher, the "squat" will be more on the bow, because the associated factor "displacement volume" causes to the low-pressure environment due to large and rapid turbulence. Thus, the bow sinks further, which faced with liquid's weaker lift force. The vessels Gerardus Mercator, Queen Elizabeth and Costa Concordia had accidents because of unified reasons of squat, fast water mass displacement by hull push and propeller suction interaction. In the case of water mass displacement from the bow side away, that accident occurred in 2005 by the vessel Gerardus Mercator with excessive longitudinal trim angularity in the shallow water. The vessel Costa Concordia (2012), voluminous water displaced from the rear left side was an important factor because of the sharp manoeuvre of that the captain made before the accident. Observations before the accident indicate that full-speed sharp turn provided listed position for the ship from left (port side) in the direction of travel before colliding and then strike a rock on the sloping side of the seabed. The reason why the ship drifted to the left depends mainly the water discharge occurred at the left side of the hull during left-hand rudder

  20. Accidents in nuclear ships

    Energy Technology Data Exchange (ETDEWEB)

    Oelgaard, P L [Risoe National Lab., Roskilde (Denmark); [Technical Univ. of Denmark, Lyngby (Denmark)

    1996-12-01

    This report starts with a discussion of the types of nuclear vessels accidents, in particular accidents which involve the nuclear propulsion systems. Next available information on 61 reported nuclear ship events in considered. Of these 6 deals with U.S. ships, 54 with USSR ships and 1 with a French ship. The ships are in almost all cases nuclear submarines. Only events that involve the sinking of vessels, the nuclear propulsion plants, radiation exposures, fires/explosions, sea-water leaks into the submarines and sinking of vessels are considered. For each event a summary of available information is presented, and comments are added. In some cases the available information is not credible, and these events are neglected. This reduces the number of events to 5 U.S. events, 35 USSR/Russian events and 1 French event. A comparison is made between the reported Soviet accidents and information available on dumped and damaged Soviet naval reactors. It seems possible to obtain good correlation between the two types of events. An analysis is made of the accident and estimates are made of the accident probabilities which are found to be of the order of 10{sup -3} per ship reactor years. It if finally pointed out that the consequences of nuclear ship accidents are fairly local and does in no way not approach the magnitude of the Chernobyl accident. It is emphasized that some of the information on which this report is based, may not be correct. Consequently some of the results of the assessments made may not be correct. (au).

  1. Accidents in nuclear ships

    International Nuclear Information System (INIS)

    Oelgaard, P.L.

    1996-12-01

    This report starts with a discussion of the types of nuclear vessels accidents, in particular accidents which involve the nuclear propulsion systems. Next available information on 61 reported nuclear ship events in considered. Of these 6 deals with U.S. ships, 54 with USSR ships and 1 with a French ship. The ships are in almost all cases nuclear submarines. Only events that involve the sinking of vessels, the nuclear propulsion plants, radiation exposures, fires/explosions, sea-water leaks into the submarines and sinking of vessels are considered. For each event a summary of available information is presented, and comments are added. In some cases the available information is not credible, and these events are neglected. This reduces the number of events to 5 U.S. events, 35 USSR/Russian events and 1 French event. A comparison is made between the reported Soviet accidents and information available on dumped and damaged Soviet naval reactors. It seems possible to obtain good correlation between the two types of events. An analysis is made of the accident and estimates are made of the accident probabilities which are found to be of the order of 10 -3 per ship reactor years. It if finally pointed out that the consequences of nuclear ship accidents are fairly local and does in no way not approach the magnitude of the Chernobyl accident. It is emphasized that some of the information on which this report is based, may not be correct. Consequently some of the results of the assessments made may not be correct. (au)

  2. Characteristics of plutonium, curium and uranium in hulls of FUGEN MOX spent fuel by destructive analysis

    International Nuclear Information System (INIS)

    Iijima, Shizuka; Goto, Yuichi; Samoto, Hirotaka; Shichi, Ryo; Shimizu, Takenori

    2011-01-01

    We have been developing a non-destructive assay system called hulls monitor for nuclear fuel materials retained in hulls at the Tokai Reprocessing Plant (TRP). The hulls monitor is based on a passive neutron measurement method, so its applicability should be evaluated by a destructive analysis of hulls that are recovered from the reprocessing process. In this study, hulls came from the Advanced Thermal Reactor (ATR) FUGEN were taken from the dissolution process of TRP and destructively analyzed. Two kinds of hulls from ATR-MOX spent fuel assemblies and from ATR-UO 2 spent fuel assemblies were taken and soaked with nitric acid then fused with ammonium hydrogen sulfate, followed by Pu, 244 Cm, U mass determination by alpha spectrometry and ICP-AES. The characteristics of hulls came from MOX spent fuel assemblies were revealed by comparison of ATR-MOX spent fuel with ATR-UO 2 spent fuel. (author)

  3. Prototype evaluation of transformation toughened blast resistant naval hull steels: Part II

    Science.gov (United States)

    Saha, A.; Jung, J.; Olson, G. B.

    2007-07-01

    Application of a systems approach to computational materials design led to the theoretical design of a transformation toughened ultratough high-strength plate steel for blast-resistant naval hull applications. A first prototype alloy has achieved property goals motivated by projected naval hull applications requiring extreme fracture toughness (C v > 85 ft-lbs or 115 J corresponding to K Id≥ 200 ksi.in1/2 or 220 MPa.m1/2) at strength levels of 150 180 ksi (1,030 1,240 MPa) yield strength in weldable, formable plate steels. A continuous casting process was simulated by slab casting the prototype alloy as a 1.75‧‧ (4.45 cm) plate. Consistent with predictions, compositional banding in the plate was limited to an amplitude of 6 7.5 wt% Ni and 3.5 5 wt% Cu. Examination of the oxide scale showed no evidence of hot shortness in the alloy during hot working. Isothermal transformation kinetics measurements demonstrated achievement of 50% bainite in 4 min at 360 °C. Hardness and tensile tests confirmed predicted precipitation strengthening behavior in quench and tempered material. Multi-step tempering conditions were employed to achieve the optimal austenite stability resulting in significant increase of impact toughness to 130 ft-lb (176 J) at a strength level of 160 ksi (1,100 MPa). Comparison with the baseline toughness strength combination determined by isochronal tempering studies indicates a transformation toughening increment of 65% in Charpy energy. Predicted Cu particle number densities and the heterogeneous nucleation of optimal stability high Ni 5 nm austenite on nanometer-scale copper precipitates in the multi-step tempered samples was confirmed using three-dimensional atom probe microanalysis. Charpy impact tests and fractography demonstrate ductile fracture with C v > 80 ft-lbs (108 J) down to -40 °C, with a substantial toughness peak at 25 °C consistent with designed transformation toughening behavior. The properties demonstrated in this first

  4. Development on the automatic separator of separation of residual powders from SF hulls

    International Nuclear Information System (INIS)

    Jung, Jae Hoo; Kim, Young Hwang; Kim, Ki Ho; Park, Byung Buk; Lee, Hyo Jik; Kim, Sung Hyun; Park, Hee Sung; Lee, Jong Kwang; Kim, Ho Dong

    2009-12-01

    At the previous process of auto hull separator, vol-oxidizer convert UO 2 pellets to U 3 O 8 powder, and in the next step, hulls and powders is collected into each part of two vessels. In order to enhance the recover rate, fine powders on the surface of hulls should be removed from hulls. Auto hulls separator for fine powders is a device which can separate fine powders from hulls. In order to design and manufacture this device, we analyzed fine powders which are remained on the surface of hulls for separation properties, and selected separation and operation methods. Also, the main mechanism is devised by using the design considerations. These main mechanism consists of rotation drum, parts feeder, hull conveyer, powders separator, air shower, and vessels. Design considerations for auto hulls separator as follows ; capacity : 100 kg HM/batch, rod-cut length : 50 mm, recovery rate for fine powders : 95 % and operation condition : over 12 hrs/batch. We considered connection methods of the vessel and high vacuum module which can join with the outlet of auto hulls separator. Also, by using the above results, we have manufactured auto hulls separator for fine powders, and conducted blank tests for operation condition. Here, hulls of 50 mm length for test are used with 20 kg HM/batch. We have conducted separation tests of 2 batches to collect fine powders with hulls of 10 kg HM/batch. Our goal of recovery rate was 95%, but in the test result, the recovery rate of fine powders on the surface of hulls was over 96 %

  5. Development of superconducting ship propulsion system

    International Nuclear Information System (INIS)

    Sakuraba, Junji; Mori, Hiroyuki; Hata, Fumiaki; Sotooka, Koukichi

    1991-01-01

    When we plan displacement-type monohull high speed vessels, it is difficult to get the hull form with the wave-making resistance minimum, because the stern shape is restricted by arrangement of propulsive machines and shafts. A small-sized and light-weight propulsive machines will reduce the limit to full form design. Superconducting technology will have capability of realizing the small-sized and light-weight propulsion motor. The superconducting electric propulsion system which is composed of superconducting propulsion motors and generators, seems to be an ideal propulsion system for future vehicles. We have constructed a 480 kW superconducting DC homopolar laboratory test motor for developing this propulsion system. The characteristic of this motor is that it has a superconducting field winding and a segmented armature drum. The superconducting field winding which operates in the persistent current mode, is cooled by a condensation heat exchanger and helium refigerating system built into the cryostat of the superconducting field winding. The operating parameters of this motor agreed well with the design parameters. Using the design concepts of this motor, we have conceptually designed a 150,000-200,000 PS superconducting electric propulsive system for a displacement-type monohull high speed ship. (author)

  6. Study on variation in ship's forward speed under regular waves depending on rudder controller

    Directory of Open Access Journals (Sweden)

    Sung-Soo Kim

    2015-03-01

    Full Text Available The purpose of this research is to compare and analyze the advanced speed of ships with different rudder controller in wavy condition by using a simulation. The commercial simulation tool named AQWA is used to develop the simulation of ship which has 3 degree of freedom. The nonlinear hydrodynamic force acting on hull, the propeller thrust and the rudder force are calculated by the additional subroutine which interlock with the commercial simulation tool, and the regular wave is used as the source of the external force for the simulation. Rudder rotational velocity and autopilot coefficients vary to make the different rudder controller. An advanced speed of ships depending on the rudder controller is analyzed after the autopilot simulations.

  7. The present status of Japan Nuclear Ship Development Agency in fiscal 1981

    International Nuclear Information System (INIS)

    1982-01-01

    In the nuclear ship ''Mutsu'', the repair of shielding on the ship itself was completed in March, and on the reactor plant in January, 1982. Comprehensive safety check-up on both hardware and software, started in October, 1975, has been finished within fiscal 1981, except some on hardware. On the basis of the results, repair work is in progress to raise the safety and reliability of the reactor plant. As the new home port of the n.s. Mutsu, the Sekinehama area in Aomori Prefecture has been chosen as its candidate, where site survey was carried out. The following matters are described: shielding repair work on the ship hull and reactor plant, safety check-up on reactor plant components and plant design, the analysis of reactor plant accident, the candidate home port for the n.s. Mutsu and the results of its site survey. (J.P.N.)

  8. Conclusions from collision examinations for nuclear merchant ships in the FRG

    International Nuclear Information System (INIS)

    Woisin, G.

    1978-01-01

    In Germany model tests have been performed for the utilization of a resisting type barrier instead of an energy absorbing type barrier, the latter used in nuclear merchant ships up to now only. After reviewing the model technique the results of nine tests with the new barrier are discussed. Calculations performed to the newly raised questions of the shock accelerations of the reactor plant and of possible overstressing of the hull are reported. The new design has many advantages with respect to safety and to the arrangement of a reactor plant in a ship too. Some questions partly remain unanswered at the moment concerning oblique collisions to the ends of the barrier and the possible effects of bulk cargo in holds close to the bow in striking ships of smaller size

  9. Reliability-based assessment of deteriorating ship structures operating in multiple sea loading climates

    Energy Technology Data Exchange (ETDEWEB)

    Moan, Torgeir [Centre for Ships and Ocean Structures, Norwegian University of Science and Technology, Marine Technology Centre, Tyholt, N 7491 Trondheim (Norway)], E-mail: tormo@marin.ntnu.no; Ayala-Uraga, Efren [Department of Marine Technology, Norwegian University of Science and Technology, Marine Technology Centre, Tyholt, N 7491 Trondheim (Norway)

    2008-03-15

    A reliability-based model for assessment of deteriorating ships subjected to multiple environmental conditions is established. Deterioration due to combined crack growth and corrosion in structural components of a ship hull is accounted for based on a fracture mechanics formulation. The model enables to take into account the corrosion-induced increased crack growth rate in two ways: (1) the increased stress range produced by the plate thinning (wastage) effect and (2) corrosion fatigue itself. Sensitivity studies are carried out to evaluate the effect of inspection updating on a production ship subjected to two different climate conditions. The hazard rate concept is adopted as a measure of reliability and emphasized throughout the different case studies.

  10. Shielding repair and comprehensive safety inspection of the nuclear-powered ship Mutsu

    International Nuclear Information System (INIS)

    Takada, Etsuo

    1982-01-01

    Eight years after the radiation leakage accident, the nuclear-powered ship Mutsu returned again to its home port Ominato. During the period, for four years, the n.s. Mutsu was subjected to shielding repair and comprehensive inspection at Sasebo port. In the future, the ship will start on experimental navigation after its functional and power-up tests. The works of shielding repair and the comprehensive inspection with subsequent repair are described in technical aspects. The basic policy of the repair was two points, i.e. the usage of shielding materials excellent in shielding capacity, less in radioactivation and enduring operating temperature, and structural strength resisting ship-hull acceleration, shock and vibration, enabling easy maintenance and inspection. Comprehensive inspection was made on not only machinery integrity but also the design itself. (Mori, K.)

  11. Extreme value prediction of the wave-induced vertical bending moment in large container ships

    DEFF Research Database (Denmark)

    Andersen, Ingrid Marie Vincent; Jensen, Jørgen Juncher

    2015-01-01

    increase the extreme hull girder response significantly. Focus in the present paper is on the influence of the hull girder flexibility on the extreme response amidships, namely the wave-induced vertical bending moment (VBM) in hogging, and the prediction of the extreme value of the same. The analysis...... in the present paper is based on time series of full scale measurements from three large container ships of 8600, 9400 and 14000 TEU. When carrying out the extreme value estimation the peak-over-threshold (POT) method combined with an appropriate extreme value distribution is applied. The choice of a proper...... threshold level as well as the statistical correlation between clustered peaks influence the extreme value prediction and are taken into consideration in the present paper....

  12. The future frigates of the French navy: all electric ships?

    Energy Technology Data Exchange (ETDEWEB)

    Letot, L. [Delegation Generale pour l' Armement/Direction des Systemes de forces et de la Prospective (DGA/DSP/SASF), 75 - Paris (France); Herjean, Y. [EMM/PL/EPG, France (France)

    2000-07-01

    The application of the all electric ship concept is interesting in the context of several types of warship. Although there it does not pose any major difficulties for simple ships (replenishment ships, amphibious ships) and can be implemented with off-the-shelf technology, its application to combat ships is more ambitious and risky. The renewal of a major part of our frigate fleet in 2008 offers the opportunity to apply this concept. The military and economic advantages have to be demonstrated. Having summarized the programme, the paper discusses the advantages of the all electric concept and examines several areas of technological difficulty that will need to be resolved. Finally, the paper presents work in progress, which will determine whether or not the electric solution is retained for the future multi-mission frigate. (authors)

  13. Ship operations report, 1973

    International Nuclear Information System (INIS)

    1973-01-01

    The NOAA Fleet Operations Report 1973 was developed to provide a summary of project accomplishments during calendar year 1973. The report was prepared from season, cruise and special reports submitted by ships of the fleet. Centralized management of the NOAA Fleet was finalized by changing the operational control of the National Marine Fisheries Service (NMFS) Ships DAVID STARR JORDAN (FRS 44), TOWNSEND CROMWELL (FRS 43) and MURRE II (FRV 63) from NMFS to the National Ocean Survey on July 1, 1973. Throughout the year, ships routinely collected and transmitted weather data. Similarly, as NOAA participants in the Integrated Global Ocean Station System (IGOSS) service program, XBT observations were taken and either radioed or submitted in log form via mail. In addition, particulate and radionuclide samples were taken in cooperation with the Atomic Energy Commission, sediment samples were obtained for the Smithsonian Institution and observations were made of marine mammals

  14. Ship operations report, 1975

    International Nuclear Information System (INIS)

    1976-01-01

    The NOAA Ship Operations Report 1975 was developed to provide a summary of projects undertaken during calendar year 1975. The report was prepared from season, cruise and special reports submitted by ships of the fleet. This report is promulgated for inhouse dissemination in the National Oceanic and Atmospheric Administration, for collaborating and interested agencies, and for use by members of the scientific community. Throughout the year, ships routinely collected and transmitted weather data. Similarly, as NOAA participants in the Integrated Global Ocean Station System (IGOSS) service program, XBT observations were taken and either radioed or submitted in log form via mail. In addition, particulate and radionuclide samples were taken in cooperation with the Atomic Energy Commission, sediment samples were obtained for the Smithsonian Institution and observations were made of marine mammals

  15. Internationalisation Within Liner Shipping

    DEFF Research Database (Denmark)

    Prockl, Günter; Kinra, Aseem; Kotzab, Herbert

    2018-01-01

    , the degree of internationalisation, measured on the basis of sea-oriented operations, differs from that measured according to land-oriented front-end marketing and sales activities. The purpose of this study is to further examine the internationalisation patterns of shipping lines. An examination...... of the front-end activities and the structures of leading container-shipping companies is conducted. The sales office networks of the sector’s 20 largest companies worldwide (by twenty-foot equivalent unit capacity) are analysed as key indicators. The numbers of sales offices are measured by analysing...... the websites of the sample (20 companies), as well as annual reports and other publicly available data sources. The findings show that not all shipping companies are international, by virtue of the industry. While it is difficult to observe differences in the overall patterns of the sales networks at a macro...

  16. Shipping emissions in ports

    OpenAIRE

    Merk, Olaf

    2014-01-01

    Shipping emissions in ports are substantial, accounting for 18 million tonnes of CO2 emissions, 0.4 million tonnes of NOx, 0.2 million of SOx and 0.03 million tonnes of PM10 in 2011. Around 85% of emissions come from containerships and tankers. Containerships have short port stays, but high emissions during these stays. Most of CO2 emissions in ports from shipping are in Asia and Europe (58%), but this share is low compared to their share of port calls (70%). European ports have much less emi...

  17. Are nuclear ships environmentally safer than conventionally powered ships

    International Nuclear Information System (INIS)

    Bone, C.A.; Molgaard, C.A.; Helmkamp, J.C.; Golbeck, A.L.

    1988-01-01

    An epidemiologic analysis was conducted to determine if risk of hospitalization varied by age, ship type, or occupation between nuclear and conventional powered ship crews in the U.S. Navy. Study cohorts consisted of all male enlisted personnel who served exclusively aboard conventional or nuclear powered aircraft carriers and cruisers during the years 1975-1979; cases were those men hospitalized during this period (N = 48,242). Conventional ship personnel showed significantly elevated rates of injury and disease when compared to nuclear ship personnel. The largest relative risks by age occurred for conventional ship crewmen less than 30 years old. Seaman, logistics (supply), and healthcare personnel serving aboard conventional ships comprised the occupational groups exhibiting the highest hospitalization rate differentials. The results strongly suggest that nuclear ships provide a healthier, safer working and living environment than conventional ships

  18. Characterization of spent fuel hulls and dissolution residues

    International Nuclear Information System (INIS)

    Gue, J.P.; Andriessen, H.

    1985-04-01

    The main results obtained within the framework of CEC programmes, by KFK, UKAEA and CEA, are reviewed concerning the characterization of dissolution wastes. The contents were determined of the main radioactive emitters contained in the hulls originating in a whole fuel assembly sampled at the La Hague plant, or from Dounreay PFR fuels. Radiochemical characterizations were carried out by different methods including neutron emission measurement, alpha and beta-gamma spectrometry, and mass spectrometry. Decontamination of the hulls by using rinsings and supplementary treatment were also dealt with. The ignition and explosion risks associated with the zircaloy fines formed during the shearing of LWR fuels were examined, and the ignition properties of irradiated and unirradiated zircaloy powders were determined and compared. The physical properties and compositions of the dissolution residues of PFR fuels were defined, in order to conduct tests on the immobilization of these wastes in cement

  19. Cold-crucible melting of hulls and structural materials

    International Nuclear Information System (INIS)

    Jouan, A.; Jacquet-Francillon, N.; Puyou, M.; Piccinato, R.

    1990-01-01

    The method currently implemented at the La Hague UP3 reprocessing plant for conditioning of PWR zircaloy hulls is cement embedding. Another promising method, mainly for reducing the waste volume and the available exchange surface area, is melting. A cold-crucible melting process has therefore been developed by the CEA at Marcoule (France) over the last decade. Development work first concentrated on cladding hulls from fast breeder reactors, then from pressurized water reactors. The process can be used for both types of cladding wastes. Subassembly head and foot end-caps are sheared off and should be suitable for surface storage after α decontamination by successive rinsing. If necessary because of their α activity, they could be melted in a larger furnace

  20. SHIPPING OF RADIOACTIVE ITEMS

    CERN Multimedia

    TIS/RP Group

    2001-01-01

    The TIS-RP group informs users that shipping of small radioactive items is normally guaranteed within 24 hours from the time the material is handed in at the TIS-RP service. This time is imposed by the necessary procedures (identification of the radionuclides, determination of dose rate and massive objects require a longer procedure and will therefore take longer.

  1. Ship Roll Motion Control

    DEFF Research Database (Denmark)

    Perez, Tristan; Blanke, Mogens

    2010-01-01

    . This tutorial paper presents an account of the development of various ship roll motion control systems and the challenges associated with their design. The paper discusses how to assess performance, the applicability of dierent models, and control methods that have been applied in the past....

  2. Ship Roll Damping Control

    DEFF Research Database (Denmark)

    Perez, Tristan; Blanke, Mogens

    2012-01-01

    limitations and large variations of the spectral characteristics of wave-induced roll motion. This tutorial paper presents an account of the development of various ship roll motion control systems together with the challenges associated with their design. It discusses the assessment of performance...

  3. Options of ship discharge

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2010-05-15

    Environmental performance is a key design consideration for manufacturers of bulk handling machines, not least ship unloaders, with features being introduced to minimise dust and noise pollution. The article reports on developments in grab unloaders, slewing grabcranes and mobile grabcranes by manufacturers such as Konecrane, EMS-Tech, Liebherr-Werk Nenzing and Gottwald. 2 photos.

  4. Biofouling and Design of a Biomimetic Hull-Grooming Tool

    Science.gov (United States)

    2007-09-14

    have barred the use of organotin compounds such as tributyltin ( TBT ) and copper-based paints, which are currently used by the Navy and have become...copper into the water, killing the fouling organisms. There is new research in biomimetic polymers that deter fouling, but are non- toxic . These polymers...is new research in biomimetic polymers that deter fouling, but are non- toxic . These polymers are rigidly attached to the hull surface extending

  5. Hulls and structural material waste conditioning by high pressure compaction

    International Nuclear Information System (INIS)

    Frotscher, H.

    1991-01-01

    Since 1986 KfK is developing a conditioning process. Main subjects of the investigations were the development of the production technique and the planning of the most important equipments of the process under remote conditions. The process is based on an extensive program of experiments. Inactive bulks of hulls and structural material components were compacted using maximum axial pressure load of about 300 MPa. The product density as function of press force was experimentally determinated. The mechanical loads of the press and tools were estimated for the design of these equipments. The hydraulic press consists a horizontal four-cylinder press. The maximum force of the press is 25 MN. The main advantage is the modular design of the press which is open on all sides. Especially the free accessibility from top is ensured. The report also represents relevant radiological data of the alternative product. Co-60 is the dominating activity of the product due to the effects of the heat production. An amount of 10 kg hull waste or 25 kg top and bottom pieces of the spent fuel assemblies per package is already beyond the Co-60 limit of the KONRAD regulations. The nuclear thermal power of a filled container is approximately sixty times lower compared with a vitrified HLW-container. Since the product shows thermal stability beyond 200 0 C, this it is suited for a combined disposal together with vitrified HLW-containers in salt bore holes of a geological disposal. The preliminary cost evaluation is based on a reprocessing throughput of 500 t HM per year and volume reduction factor of 5.3. Accordingly there are produced 300 waste packages with hulls only or 625 units with hulls and top and bottom pieces which require 1.6 or 2.3 millions DM respectively

  6. Classification of Ship Routing and Scheduling Problems in Liner Shipping

    DEFF Research Database (Denmark)

    Kjeldsen, Karina Hjortshøj

    2011-01-01

    This article provides a classification scheme for ship routing and scheduling problems in liner shipping in line with the current and future operational conditions of the liner shipping industry. Based on the classification, the literature is divided into groups whose main characteristics...

  7. Wallops Ship Surveillance System

    Science.gov (United States)

    Smith, Donna C.

    2011-01-01

    Approved as a Wallops control center backup system, the Wallops Ship Surveillance Software is a day-of-launch risk analysis tool for spaceport activities. The system calculates impact probabilities and displays ship locations relative to boundary lines. It enables rapid analysis of possible flight paths to preclude the need to cancel launches and allow execution of launches in a timely manner. Its design is based on low-cost, large-customer- base elements including personal computers, the Windows operating system, C/C++ object-oriented software, and network interfaces. In conformance with the NASA software safety standard, the system is designed to ensure that it does not falsely report a safe-for-launch condition. To improve the current ship surveillance method, the system is designed to prevent delay of launch under a safe-for-launch condition. A single workstation is designated the controller of the official ship information and the official risk analysis. Copies of this information are shared with other networked workstations. The program design is divided into five subsystems areas: 1. Communication Link -- threads that control the networking of workstations; 2. Contact List -- a thread that controls a list of protected item (ocean vessel) information; 3. Hazard List -- threads that control a list of hazardous item (debris) information and associated risk calculation information; 4. Display -- threads that control operator inputs and screen display outputs; and 5. Archive -- a thread that controls archive file read and write access. Currently, most of the hazard list thread and parts of other threads are being reused as part of a new ship surveillance system, under the SureTrak project.

  8. Treatment of stainless steels and zircaloy cladding hulls

    International Nuclear Information System (INIS)

    Jenkins, I.L.; Taylor, R.F.

    1978-01-01

    Results are reported on the fissile material content and the distribution of alpha and beta-gamma emitters in both types of cladding. Apart from very small amounts of residual fuel, fissile material is present as a deposit formed during the dissolution of fuel and also as material driven into the cladding by fission recoil. Alpha-emitters penetrate to depths of 1-2 μm into both S.S. and Zircaloy claddings. The surface deposits on individual hulls can be effectively removed by refluxing with nitric acid or by cleaning with nitric acid in an ultrasonic bath. The physical structural and handling behavior of hull assemblies are examined as being of key importance to the establishment of an efficient cleaning process. The reference leaching target is to extract residual fuel fragments and to remove surface deposits. Preferred routes for compaction, drumming, and encapsulation are briefly reviewed with regard to achieving a final package volume half that of the original hulls with associated hardware

  9. On the Influence of Hull Girder Flexibility on the Wave

    DEFF Research Database (Denmark)

    Seng, Sopheak; Andersen, Ingrid Marie Vincent; Jensen, Jørgen Juncher

    2012-01-01

    Numerical predictions and model test results of the wave induced bending moments in a 9,400 TEU post-Panamax container vessel are presented for two regular wave scenarios. Different numerical procedures have been applied: a linear and non-linear time-domain strip theory and a direct calculation (...... (CFD) solving the Navier-Stokes equations with the free surface captured by a volume-of-fluid (VOF) method. In all procedures the flexibility of the hull girder is modelled as a non-uniform Timoshenko beam. It is observed that the non-linear models agree well with the model tests...... and as there is no occurrence of severe slamming in the cases considered, the inexpensive non-linear strip theory is as accurate as the direct CFD calculation method. In a comparison with the results using the rigid body assumption, the increase in the vertical bending moment (VBM) amidships due to the flexibility of the hull...... girder is found to be approximately 7% (peak-to-peak amplitude) in general. The non-linear responses, however, contain over-harmonic frequencies which may coincide with the natural frequency of the two-node vertical bending mode inducing resonance. In that case the hull girder flexibility causes...

  10. Treatment of cladding hulls by the HIPOW process

    International Nuclear Information System (INIS)

    Larker, H.T.; Tegman, R.

    1981-01-01

    The conditions for densifying and bonding Zircaloy cladding hulls from spent LWR fuel to blocks by the HIPOW (hot isostatic pressing of waste) process have been studied. Fully dense and mechanically strong blocks of Zircaloy can be made without additives at temperatures around 1000 0 C. A volume reduction of about seven times and surface area reduction of more than 300 times, compared to typical loose-filled cladding hulls remaining after the chop-leach operations in a reprocessing plant, can be obtained. A study of a possible process for industrial scale has been made. Handling under water can prevent any fire hazard in the preparation sequence. The use of a special hermetically sealed double-wall metal container encasing the hulls during the densification in the hot isostatic press virtually eliminates the problem of lasting contamination of this equipment, thus greatly simplifying service and maintenance. One hot isostatic press can serve a reprocessing line with an LWR fuel capacity of 800 tons/year. Fines (residues) from fuel dissolution and alpha-contaminated ashes from incinerated organic materials in the plant may also be incorporated in the Zircaloy blocks. Tritium can quantitatively be contained in these blocks

  11. Flooding and schools: experiences in Hull in 2007.

    Science.gov (United States)

    Convery, Ian; Carroll, Bob; Balogh, Ruth

    2015-01-01

    Hull, a city in the East Riding of Yorkshire, United Kingdom, suffered severe flooding in June 2007, affecting some 8,600 households and most schools. Despite the potential for damage in such disasters, no studies of the effects of floods on teachers and schools in the UK appear to have been published previously. This study analysed the impacts of the floods on teachers in Hull in two stages: first through correspondence with Hull City Council and a mailed questionnaire to 91 head teachers of primary, secondary, and special schools; and second, through in-depth interviews with head teachers from six flooded schools, representing different degrees of flood experience, and a questionnaire completed by eight teachers from the same schools. The findings reveal the importance and the complexity of the role of the school in the wider community in a time of crisis. The study highlights issues concerning preparedness for floods, support for schools, and flood protection for schools. © 2014 The Author(s). Disasters © Overseas Development Institute, 2014.

  12. Fabrication of renewable biocomposites from soy hull and bioplastics

    Science.gov (United States)

    Nanda, Malaya Ranjan

    This is an investigation for fabrication of biocomposites from soy hull and bioplastics like polylactide (PLA) and polyhydroxy butyrate-co- valerate (PHBV). The study was divided into three parts; the first was the development of a suitable PHBV/PLA blend. The second part involved the fabrication of composites from soy hull and PHBV/PLA blend and its comparison with polypropylene (PP)/soy hull composites. The third part was the effect of compatibilizer on the performance of the composites. From tensile study, the elongation of an optimized blend was found to be improved by 148 and 250% over the virgin polymers PHBV and PLA respectively. Scanning electron microscope revealed a stronger fiber-matrix interaction in PHBV/PLA composites over PP composites. Furthermore, the compatibilizer improved the impact and flexural strength by 56 and 32% respectively over the un-compatibilized counterpart; more significantly the resulting compatibilized composites showed improved hydrophobicity by more than 22% over un-compatibilized counterpart.

  13. Mini-review: Assessing the drivers of ship biofouling management--aligning industry and biosecurity goals.

    Science.gov (United States)

    Davidson, Ian; Scianni, Christopher; Hewitt, Chad; Everett, Richard; Holm, Eric; Tamburri, Mario; Ruiz, Gregory

    2016-01-01

    Biofouling exerts a frictional and cost penalty on ships and is a direct cause of invasion by marine species. These negative consequences provide a unifying purpose for the maritime industry and biosecurity managers to prevent biofouling accumulation and transfer, but important gaps exist between these sectors. This mini-review examines the approach to assessments of ship biofouling among sectors (industry, biosecurity and marine science) and the implications for existing and emerging management of biofouling. The primary distinctions between industry and biosecurity in assessment of vessels biofouling revolve around the resolution of biological information collected and the specific wetted surface areas of primary concern to each sector. The morphological characteristics of biofouling and their effects on propulsion dynamics are of primary concern to industry, with an almost exclusive focus on the vertical sides and flat bottom of hulls and an emphasis on antifouling and operational performance. In contrast, the identity, biogeography, and ecology of translocated organisms is of highest concern to invasion researchers and biosecurity managers and policymakers, especially as it relates to species with known histories of invasion elsewhere. Current management practices often provide adequate, although not complete, provision for hull surfaces, but niche areas are well known to enhance biosecurity risk. As regulations to prevent invasions emerge in this arena, there is a growing opportunity for industry, biosecurity and academic stakeholders to collaborate and harmonize efforts to assess and manage biofouling of ships that should lead to more comprehensive biofouling solutions that promote industry goals while reducing biosecurity risk and greenhouse gas emissions.

  14. Added masses of ship structures

    CERN Document Server

    Korotkin, Alexandr I

    2008-01-01

    This essentially self-contained reference book contains data on added masses of ships and various ship and marine engineering structures. Theoretical and experimental methods for determining added masses of these objects are described.

  15. Ship Observations - VOS and Navy

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Combination of Voluntary Observing Ship (VOS) and US Navy Ship weather observations. Obs generally taken 2-4 times daily at 00, 06, 12, and 18z.

  16. Trends of shipping markets development

    Directory of Open Access Journals (Sweden)

    Tomasz Nowosielski

    2012-06-01

    Full Text Available Shipping markets are dependent on international trade transactions that generate transport needs. These needs can dynamically change depending on global natural resources and commodity markets situation. The changes affecting shipping markets can also be caused by changes to the existing cargo flows and by establishing new ones in different geographies. It is anticipated that in the future shipping markets will change, visible by a decline in shipping in North America and Europe and an increase in Asia.

  17. High cost for drilling ships

    International Nuclear Information System (INIS)

    Hooghiemstra, J.

    2007-01-01

    Prices for the rent of a drilling ship are very high. Per day the rent is 1% of the price for building such a ship, and those prices have risen as well. Still, it is attractive for oil companies to rent a drilling ship [nl

  18. The Effect of Material and Side Walls on Hull Deflection during a Blast Event

    Science.gov (United States)

    2017-12-13

    ARL-CR-0822 ● DEC 2017 US Army Research Laboratory The Effect of Material and Side Walls on Hull Deflection during a Blast Event...Army Research Laboratory The Effect of Material and Side Walls on Hull Deflection during a Blast Event prepared by Danielle Abell SURVICE...Walls on Hull Deflection during a Blast Event 5a. CONTRACT NUMBER W911QX-16-D-0014 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S

  19. Towards Real Time Simulation of Ship-Ship Interaction

    DEFF Research Database (Denmark)

    Lindberg, Ole; Bingham, Harry B.; Engsig-Karup, Allan Peter

    2012-01-01

    We present recent and preliminary work directed towards the development of a simplified, physics-based model for improved simulation of ship-ship interaction that can be used for both analysis and real-time computing (i.e. with real-time constraints due to visualization). The goal is to implement...... accurate (realistic) and much faster ship-wave and ship-ship simulations than are currently possible. The coupling of simulation with visualization should improve the visual experience such that it can be perceived as more realistic in training. Today the state-of-art in real-time ship-ship interaction...... is for efficiency reasons and time-constraints in visualization based on model experiments in towing tanks and precomputed force tables. We anticipate that the fast, and highly parallel, algorithm described by Engsig-Karup et al. [2011] for execution on affordable modern high-throughput Graphics Processing Units...

  20. Study on characteristics of response to nodal vibration in a main hull of a large-size ferry boat; Ogata feri no shusentai yodo oto tokusei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Takimoto, T; Yamamoto, A; Kasuda, T; Yanagi, K [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1996-04-10

    Demand for reduction in vibration and noise in large-size ferry boats has been severer in recent years. On the other hand, vibration exciting force in main engines and propellers is on an increasing trend in association with increase in speed and horsepower. A large-size ferry boat uses an intermediate-speed diesel engine which has high vibration exciting frequency. Therefore, discussions were given on characteristics of response to nodal vibration in a main hull induced by primary internal moment in a main engine in a large-size ferry boat mounting an intermediate speed main engine. Results of detailed vibration calculations, vibration experiments using an actual ship, and results of measurements were used for the discussions. Natural frequency for two-node vibration above and below the main hull was set for an equation of estimation such that the whole ship is hypothesized to have been structured with beams having the same cross section according to the Todd`s equation, and effect of rigidity of the long structure can be evaluated. Parameters were derived by using the minimum square method that uses the measured natural frequency of the ship A through the ship E among large-size ferry boats. The derived result may be summarized as follows: this equation of estimation has an estimation error of about 5% against the natural frequency for nodal vibration above and below the main hull; and this equation of estimation has an estimation error of about 30% against the acceleration in the vertical direction at the end of the stern. 2 refs., 11 figs., 1 tab.

  1. Calculation of Flows Over Underwater Bodies with Hull, Sail and Appendages

    International Nuclear Information System (INIS)

    Shoab, M.; Ayub, M.; Bilal, S.; Zahir, S.; Khan, M.A.

    2004-01-01

    A comprehensive study has been made for the hydrodynamic analysis of the submarine DARPA 2. The analysis was first performed for hull, then hull with sail on top and then for the complete submarine including hull, sail and appendages. A comparison of tangential velocity and pressure distribution for hull is accomplished using CFD flow solvers and published data. Further, the pressure distribution over the hull with sail is also analyzed. Finally, pressure distribution, forces and moments were calculated over the complete submarine including hull, sail and appendages. Comparison 01 pressure distribution and tangential velocity for the hull show a good agreement with published data. Pressure coefficient comparison for the hull with sail shows the good CFD-CFD agreement. Comparison of Normal force and pitching moment of complete submarine having hull, sail and appendages shows a reasonable agreement with the experimental results of DARPA 2. Both quantitative and qualitative analysis of the complete submarine estimates the required design force and moment at different angles of attack and also demonstrate the flow visualization. (author)

  2. Genetic control of a transition from black to straw-white seed hull in rice domestication.

    Science.gov (United States)

    Zhu, Bo-Feng; Si, Lizhen; Wang, Zixuan; Zhou, Yan; Zhu, Jinjie; Shangguan, Yingying; Lu, Danfeng; Fan, Danlin; Li, Canyang; Lin, Hongxuan; Qian, Qian; Sang, Tao; Zhou, Bo; Minobe, Yuzo; Han, Bin

    2011-03-01

    The genetic mechanism involved in a transition from the black-colored seed hull of the ancestral wild rice (Oryza rufipogon and Oryza nivara) to the straw-white seed hull of cultivated rice (Oryza sativa) during grain ripening remains unknown. We report that the black hull of O. rufipogon was controlled by the Black hull4 (Bh4) gene, which was fine-mapped to an 8.8-kb region on rice chromosome 4 using a cross between O. rufipogon W1943 (black hull) and O. sativa indica cv Guangluai 4 (straw-white hull). Bh4 encodes an amino acid transporter. A 22-bp deletion within exon 3 of the bh4 variant disrupted the Bh4 function, leading to the straw-white hull in cultivated rice. Transgenic study indicated that Bh4 could restore the black pigment on hulls in cv Guangluai 4 and Kasalath. Bh4 sequence alignment of all taxa with the outgroup Oryza barthii showed that the wild rice maintained comparable levels of nucleotide diversity that were about 70 times higher than those in the cultivated rice. The results from the maximum likelihood Hudson-Kreitman-Aguade test suggested that the significant reduction in nucleotide diversity in rice cultivars could be caused by artificial selection. We propose that the straw-white hull was selected as an important visual phenotype of nonshattered grains during rice domestication.

  3. Decontamination of fast reactor hulls and properties of immobilised waste forms

    International Nuclear Information System (INIS)

    Biddle, P.; Brown, P.E.; Rees, J.H.

    1986-01-01

    The studies described in this Report have been carried out on five batches of stainless steel hulls resulting from the reprocessing of fuel from the Prototype Fast Reactor at Dounreay. Direct immobilisation in cement and decontamination have been examined as possible routes for treating the hulls. A number of low temperature chemical techniques have been used to remove actinides and fission products from the hulls. The levels of α-activity could be reduced to less than 0.3 Ci/te of hulls. Thus decontamination might permit cheaper disposal than would be the case for undecontaminated hulls. 10mm sections of hulls have been immobilised in two cements in which either sand or blast furnace slag was used to extend the ordinary Portland cement. The level of Cs-137 leached from hulls immobilised in either of the cement compositions was about an order of magnitude lower than that leached from the bare hulls. For Sr-90, the BFS/OPC matrix gave a tenfold better retention than the sand/OPC. Ru-106 and Sb-125 were leached from the sand/OPC but not from the BFS/OPC samples. The preliminary studies suggested that cement was a satisfactory matrix for immobilising hulls and that the BFS/OPC was the better formulation. 30 refs, 26 tabs, 23 figs

  4. Multi-Point Hermes Acoustic Modem for High-Speed, High-Frequency Acoustic Communications with Low-Frequency Acoustic Control Loop for Real-Time Transmission of AUV-Carried High-Resolution Images and Navigation Data in Support of Ship Hulls Inspection

    Science.gov (United States)

    2013-08-31

    13.3 µs) used in the data frame. The preamble uses direct-sequence spread spectrum (DSSS) to reduce the negative impact of fading. Three bits... ifr t covers one of the allocated hops of index  h i . The received reference symbol transmitted in hop   1,2,..., Hh i N is    ( )h...are recovered based on the phase difference between the constellation points demodulated from the sub-band m of the information symbol  ( ) ifr t

  5. Estimation of Ship Long-term Wave-induced Bending Moment using Closed-Form Expressions

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher; Mansour, A. E.

    2002-01-01

    A semi-analytical approach is used to derive frequency response functions and standard deviations for the wave-induced bending moment amidships for mono-hull ships. The results are given as closed-form expressions and the required input information for the procedure is restricted to the main......-empirical closed-form expression for the skewness. The effect of whipping is included by assuming that whipping and wave-induced responses are conditionally independent given Hs. The procedure is simple and can be used to make quick estimates of the design wave bending moment at the conceptual design phase...

  6. EMP coupling to ships

    International Nuclear Information System (INIS)

    Deadrick, F.J.; Cabayan, H.S.; Kunz, K.F.; Bevensee, R.M.; Martin, L.C.; Egbert, R.W.

    1980-01-01

    Scale-model tests were conducted to establish the adequacy and limitations of model measurements as tools for predicting electromagnetic pulse (EMP) coupling voltages and currents to the critical antennas, cables, and metallic structures on ships. The scale-model predictions are compared with the results of the full-scale EMP simulation test of the Canadian ASW ship, HMCS Huron. (The EMP coupling predictions in this report were made without prior knowledge of the results of the data from the HMCS Huron tests.) This report establishes that the scale-model tests in conjunction with the data base from EMP coupling modules provides the necessary information for source model development and permits effective, low-cost study of particular system configurations. 184 figures, 9 tables

  7. SHIPPING OF RADIOACTIVE ITEMS

    CERN Multimedia

    TIS/RP Group

    2001-01-01

    The TIS-RP group informs users that shipping of small radioactive items is normally guaranteed within 24 hours from the time the material is handed in at the TIS-RP service. This time is imposed by the necessary procedures (identification of the radionuclides, determination of dose rate, preparation of the package and related paperwork). Large and massive objects require a longer procedure and will therefore take longer.

  8. Ship and Shoot

    Science.gov (United States)

    Woods, Ron

    2012-01-01

    Ron Woods shared incredibly valuable insights gained during his 28 years at the Kennedy Space Center (KSC) packaging Flight Crew Equipment for shuttle and ISS missions. In particular, Woods shared anecdotes and photos from various processing events. The moral of these stories and the main focus of this discussion were the additional processing efforts and effects related to a "ship-and-shoot" philosophy toward flight hardware.

  9. HEURISTIC METHOD OF SHIPS SELECTION FOR THE COORDINATED WORK OF WATER TRANSPORT

    Directory of Open Access Journals (Sweden)

    O. V. Shcherbina

    2018-02-01

    Full Text Available Purpose. The study aims to develop a formulation methodology for ship selection in the coordinated work of sea and river transport using a heuristic approach. Methodology. To realize the purpose set in the study, the authors carried out an analysis of domestic and foreign literature sources on the current topic, studied specifics and conditions for the effective operation of marine mono-hulled ships and composite tug/barge towing ones. Findings. The analysis results allowed formulating the heuristics methods that ensure the selection of the type sizes of tug/barge towing ships for the mixed «river-sea» navigation from the priority range of ships of the existing fleet. The proposed method makes it possible to select ships in a more appropriate manner according to the established scheme of work. Rational combinations of technical and operational characteristics of such pairs as «barges and tows», «tug/barge towing ship and sea-going ship», «tug/barge towing ship and restrictive characteristics of the area of navigation» are a prerequisite for the shipping company profit growth by increasing the capacity of ships. Originality. For the first time, the authors applied a heuristic approach to the selection of tug/barge towing ships and sea-going ones for coordinated work with the performance of cargo operations on the raid of the estuary port when transporting bulk goods. The basis of the approach is the selection of a rational mix of technical and operational characteristics of barges and tugs. The proposed approach allows determining the best combination of ship type sizes in the organization of coordinated work of sea and river transport. At the same time, the continuity of the goods transportation process from the sea ports to the river ones located in the depth of the country (and in the opposite direction is ensured. Practical value. The presented methodology is a logical continuation of the cycle of studies performed by the authors. The

  10. Advanced immobilization processes for fuel hulls and dissolver residues

    International Nuclear Information System (INIS)

    Hebel, W.; Boehme, G.; Findlay, J.R.; Sombret, C.

    1984-08-01

    Various research and development projects for the conditioning of cladding scraps and dissolver residues are pursued within the scope of the R and D programme on nuclear waste Management of the European Community. They include the characterization of the waste materials arising from industrial fuel reprocessing and the development of different waste immobilization techniques. These concern the embedment of scraps and residues into inert matrices like cement, metal alloys, compacted graphite and sintered ceramics as well as the treatment of the fuel hulls by melting or chemical conversion. The conditioned waste forms are tested as to their relevant properties for activity enclosure

  11. Advanced immobilization processes for fuel hulls and dissolver residues

    International Nuclear Information System (INIS)

    Hebel, W.; Boehme, G.; Findlay, J.R.; Sombert, C.

    1984-01-01

    Various research and development projects for the conditioning of cladding scraps and dissolver residues are pursued within the scope of the R and D programme on nuclear waste Management of the European Community. They include the characterization of the waste materials arising from industrial fuel reprocessing and the development of different waste immobilization techniques. These concern the embedment of the scraps and residues into inert matrices like cement, metal alloys, compacted graphite and sintered ceramics as well as the treatment of the fuel hulls by melting or chemical conversion. The conditioned waste forms are tested as to their relevant properties for activity enclosure

  12. Study on the preparation of furfural from rice hull

    Energy Technology Data Exchange (ETDEWEB)

    Lu, M.F; Li, P.H.

    1980-01-01

    Furfural (I) was prepared from rice hull by digestion with HCl, H/sub 2/SO4, or H/sub 3/PO4. I formation in the presence of 5N HCl (the optimum concentration) increased with increasing time of digestion up to 5 hours and then decreased. The optimum concentration and time with H/sub 2/SO4 were the same, but digestion with H/sub 3/PO4 was neither concentration nor time dependent. Under optimal conditions, I formation was highest in digestion with HCl.

  13. AN ENHANCED EQUATION FOR VIBRATION PREDICTION OF NEW TYPES OF SHIPS

    Directory of Open Access Journals (Sweden)

    Valer Cergol

    2015-09-01

    Full Text Available AA simplified approach developed to evaluate the vibration levels of complex structures such as passenger and similar ships with large shell and deck openings and extended superstructures is here presented. The final objective is to give an useful tool to ship designers, to establish since the first design stage the dynamic response of the ship with sufficient precision. This approach is based on the assumption that the ship hull can be represented as a non uniform section beam. The propeller excitations in terms of pressure pulses and shaft line moments and forces are introduced. To take into account this exciting source in the early design stage a statistical formula for dynamic excitation of propeller was developed. Furthermore the superimposition of local effects has been performed with the use of an analytical formula. The local effect due to the different space topologies such as cabins, public spaces, technical and machinery areas has been taken into account. The transversal beams, longitudinal girders, stiffeners and pillars as supported structural elements are considered in the vibration local response. The reliability of the results obtained using the formula has been improved with more precise results obtained by FEM analysis. The calculated vibration response has been verified and compared to vibration measurements performed on board of ships.

  14. maar vandag in 2015 kan hulle gelees word as stories oor mense ...

    African Journals Online (AJOL)

    8 Apr 2016 ... maar vandag in 2015 kan hulle gelees word as stories oor mense wat leef teen die agtergrond van politieke opstand en sosiale chaos binne 'n groter universele verband. Die verbeeldingspel wat geïn- spireer word deur die teater, bied in die dramatekste van Uys 'n legio visuele moontlikhede van hoe hulle ...

  15. Distributed Topological Convex Hull Estimation of Event Region in Wireless Sensor Networks without Location Information

    NARCIS (Netherlands)

    Guo, Peng; Cao, Jiannong; Zhang, Kui

    2015-01-01

    In critical event (e.g., fire or gas) monitoring applications of wireless sensor networks (WSNs), convex hull of the event region is an efficient tool in handling the usual tasks like event report, routes reconstruction and human motion planning. Existing works on estimating convex hull of event

  16. Effects of quinoa hull meal on piglet performance and intestinal epithelial physiology

    DEFF Research Database (Denmark)

    Carlson, Dorthe; Fernandez, J.A.; Poulsen, H.D.

    2012-01-01

    Saponin-containing feed additives have shown positive effects on pig performance. Quinoa hull has high saponin content and may be of interest as a feed additive. This study aimed to evaluate quinoa hull meal (QHM) as a feed additive in a pig diet. The effects of QHM were assessed for three dosages...

  17. 33 CFR 187.321 - What are the hull identification number (HIN) provisions?

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false What are the hull identification number (HIN) provisions? 187.321 Section 187.321 Navigation and Navigable Waters COAST GUARD, DEPARTMENT... Vessel Titling Systems § 187.321 What are the hull identification number (HIN) provisions? A State must...

  18. Gamma radiation effects on phenolics, antioxidants activity and in vitro digestion of pistachio (Pistachia vera) hull

    International Nuclear Information System (INIS)

    Behgar, M.; Ghasemi, S.; Naserian, A.; Borzoie, A.; Fatollahi, H.

    2011-01-01

    The effect of gamma radiation (10, 20, 30, 40, 50 and 60 kGy) on tannin, total phenolics, antioxidants activity and in vitro digestion of pistachio hulls has been investigated in this study. The possibility of using the radial diffusion method based on software measurement of the rings area has also been investigated in this study. The software based method in radial diffusion method showed a higher r 2 (0.995) value when compared to the traditional method. Irradiation reduced the tannin content (P<0.01) and activity of antioxidants (P<0.05) of pistachio hull extracts but increased the total phenolic content (P<0.05). There was no effect of gamma irradiation on the in vitro digestion of the pistachio hull. Irradiation decreased the digestion rate of the pistachio hull at the dose of 40 kGy when compared to the control. This study showed that gamma irradiation decreased tannin and antioxidants activity of pistachio hull. - Highlights: → we investigate the effects of gamma irradiation on pistachio hull. → We examine changes in phenolics, antioxidant and digestion of pistachio hull. → Computerized radial diffusion method gives precise regression for standard curve. → Gamma irradiation will decrease tannin and antioxidants of pistachio hull extracts.

  19. Effect of rice hull mulch on nutrient concentration of fertilized irrigation water

    Science.gov (United States)

    Parboiled rice hulls are an effective mulch for controlling weeds in nursery containers. A layer of rice hulls between 1.25 and 2.5 cm deep has been shown to provide effective control of liverwort (Marchantia polymorpha), bittercress (Cardamine flexuosa), and creeping woodsorrel (Oxalis corniculata...

  20. Refined universal laws for hull volumes and perimeters in large planar maps

    International Nuclear Information System (INIS)

    Guitter, Emmanuel

    2017-01-01

    We consider ensembles of planar maps with two marked vertices at distance k from each other, and look at the closed line separating these vertices and lying at distance d from the first one ( d   <   k ). This line divides the map into two components, the hull at distance d which corresponds to the part of the map lying on the same side as the first vertex and its complementary. The number of faces within the hull is called the hull volume, and the length of the separating line the hull perimeter. We study the statistics of the hull volume and perimeter for arbitrary d and k in the limit of infinitely large planar quadrangulations, triangulations and Eulerian triangulations. We consider more precisely situations where both d and k become large with the ratio d / k remaining finite. For infinitely large maps, two regimes may be encountered: either the hull has a finite volume and its complementary is infinitely large, or the hull itself has an infinite volume and its complementary is of finite size. We compute the probability for the map to be in either regime as a function of d / k as well as a number of universal statistical laws for the hull perimeter and volume when maps are conditioned to be in one regime or the other. (paper)

  1. Gamma radiation effects on phenolics, antioxidants activity and in vitro digestion of pistachio (Pistachia vera) hull

    Energy Technology Data Exchange (ETDEWEB)

    Behgar, M [Agricultural, Medical and Industrial Research School, P.O. Box 31485498, Karaj (Iran, Islamic Republic of); Ghasemi, S; Naserian, A [Faculty of Agriculture, Excellence Center in Animal Science, Ferdowsi University of Mashhad, P.O. Box 917751163, Mashhad (Iran, Islamic Republic of); Borzoie, A; Fatollahi, H [Agricultural, Medical and Industrial Research School, P.O. Box 31485498, Karaj (Iran, Islamic Republic of)

    2011-09-15

    The effect of gamma radiation (10, 20, 30, 40, 50 and 60 kGy) on tannin, total phenolics, antioxidants activity and in vitro digestion of pistachio hulls has been investigated in this study. The possibility of using the radial diffusion method based on software measurement of the rings area has also been investigated in this study. The software based method in radial diffusion method showed a higher r{sup 2} (0.995) value when compared to the traditional method. Irradiation reduced the tannin content (P<0.01) and activity of antioxidants (P<0.05) of pistachio hull extracts but increased the total phenolic content (P<0.05). There was no effect of gamma irradiation on the in vitro digestion of the pistachio hull. Irradiation decreased the digestion rate of the pistachio hull at the dose of 40 kGy when compared to the control. This study showed that gamma irradiation decreased tannin and antioxidants activity of pistachio hull. - Highlights: > we investigate the effects of gamma irradiation on pistachio hull. > We examine changes in phenolics, antioxidant and digestion of pistachio hull. > Computerized radial diffusion method gives precise regression for standard curve. > Gamma irradiation will decrease tannin and antioxidants of pistachio hull extracts.

  2. A comparison of methods for evaluating structure during ship collisions

    International Nuclear Information System (INIS)

    Ammerman, D.J.; Daidola, J.C.

    1996-01-01

    A comparison is provided of the results of various methods for evaluating structure during a ship-to-ship collision. The baseline vessel utilized in the analyses is a 67.4 meter in length displacement hull struck by an identical vessel traveling at speeds ranging from 10 to 30 knots. The structural response of the struck vessel and motion of both the struck and striking vessels are assessed by finite element analysis. These same results are then compared to predictions utilizing the open-quotes Tanker Structural Analysis for Minor Collisionsclose quotes (TSAMC) Method, the Minorsky Method, the Haywood Collision Process, and comparison to full-scale tests. Consideration is given to the nature of structural deformation, absorbed energy, penetration, rigid body motion, and virtual mass affecting the hydrodynamic response. Insights are provided with regard to the calibration of the finite element model which was achievable through utilizing the more empirical analyses and the extent to which the finite element analysis is able to simulate the entire collision event. 7 refs., 8 figs., 4 tabs

  3. The salvaging of the Mont Louis cargo ship

    International Nuclear Information System (INIS)

    Vastel, D.

    1985-01-01

    On Saturday the 25th of August 1984, at 2:20 P.M., the German car ferry Olau Britannia with 800 passengers aboard rammed the rear starboard side of the French cargo ship Mont Louis. The collision occurred in the English Channel at a point 18 kilometers north of Ostend. At 7:00 P.M. the Mont Louis sank to a depth of 15 meters at a distance of several miles by rail from Antwerp. Half the ship's hull lay uncovered at low tide. The cargo included 30 type 48-Y containers, each filled with 12 tons of UF 6 , and 22 empty type 30-B containers for return of the enriched uranium. The UF 6 was to be enriched to 4% in the Soviet Union for use as fuel in nuclear power plants. The table below details the nature of the UF 6 . After salvaging operation the containers have been inspected and no damage or leaks have been detected. The accident involved no risk of radioactive or chemical contamination of the sea water. The systematic misinformation campaign by Greenpeace and news media is briefly described. (orig./HP)

  4. Systems design of transformation toughened blast-resistant naval hull steels

    Science.gov (United States)

    Saha, Arup

    A systems approach to computational materials design has demonstrated a new class of ultratough, weldable secondary hardened plate steels combining new levels of strength and toughness while meeting processability requirements. A first prototype alloy has achieved property goals motivated by projected naval hull applications requiring extreme fracture toughness (Cv > 85 ft-lbs (115 J) corresponding to KId > 200 ksi.in1/2 (220 MPa.m1/2)) at strength levels of 150--180 ksi (1034--1241 MPa) yield strength in weldable, formable plate steels. A theoretical design concept was explored integrating the mechanism of precipitated nickel-stabilized dispersed austenite for transformation toughening in an alloy strengthened by combined precipitation of M2C carbides and BCC copper both at an optimal ˜3nm particle size for efficient strengthening. This concept was adapted to plate steel design by employing a mixed bainitic/martensitic matrix microstructure produced by air-cooling after solution-treatment and constraining the composition to low carbon content for weldability. With optimized levels of copper and M2C carbide formers based on a quantitative strength model, a required alloy nickel content of 6.5 wt% was predicted for optimal austenite stability for transformation toughening at the desired strength level of 160 ksi (1100 MPa) yield strength. A relatively high Cu level of 3.65 wt% was employed to allow a carbon limit of 0.05 wt% for good weldability. Hardness and tensile tests conducted on the designed prototype confirmed predicted precipitation strengthening behavior in quench and tempered material. Multi-step tempering conditions were employed to achieve the optimal austenite stability resulting in significant increase of impact toughness to 130 ft-lb (176 J) at a strength level of 160 ksi (1100 MPa). Comparison with the baseline toughness-strength combination determined by isochronal tempering studies indicates a transformation toughening increment of 60% in Charpy

  5. DES Prediction of Cavitation Erosion and Its Validation for a Ship Scale Propeller

    Science.gov (United States)

    Ponkratov, Dmitriy, Dr

    2015-12-01

    Lloyd's Register Technical Investigation Department (LR TID) have developed numerical functions for the prediction of cavitation erosion aggressiveness within Computational Fluid Dynamics (CFD) simulations. These functions were previously validated for a model scale hydrofoil and ship scale rudder [1]. For the current study the functions were applied to a cargo ship's full scale propeller, on which the severe cavitation erosion was reported. The performed Detach Eddy Simulation (DES) required a fine computational mesh (approximately 22 million cells), together with a very small time step (2.0E-4 s). As the cavitation for this type of vessel is primarily caused by a highly non-uniform wake, the hull was also included in the simulation. The applied method under predicted the cavitation extent and did not fully resolve the tip vortex; however, the areas of cavitation collapse were captured successfully. Consequently, the developed functions showed a very good prediction of erosion areas, as confirmed by comparison with underwater propeller inspection results.

  6. Development and application of α-hull and Voronoi diagrams in the assessment of roundness error

    International Nuclear Information System (INIS)

    Li, Xiuming; Liu, Hongqi; Li, Wei

    2011-01-01

    Computational geometry has been used to select effective data points from the measured data points for evaluating the roundness error to improve the computational complexity. However, for precision parts most of the measured points are on the vertices of the convex hull; it cannot have any effect on improving the computational complexity with the Voronoi diagrams. In this paper the roundness error is evaluated with α-hull and the Voronoi diagram instead of convex hull. An approach for constructing α-hull with the minimum radius separation is presented to determine the vertices of the Voronoi diagram. The experimental results showed that the roundness error of the minimum zone circle could be solved efficiently with α-hull and the Voronoi diagram

  7. Gamma radiation effects on phenolics, antioxidants activity and in vitro digestion of pistachio ( Pistachia vera) hull

    Science.gov (United States)

    Behgar, M.; Ghasemi, S.; Naserian, A.; Borzoie, A.; Fatollahi, H.

    2011-09-01

    The effect of gamma radiation (10, 20, 30, 40, 50 and 60 kGy) on tannin, total phenolics, antioxidants activity and in vitro digestion of pistachio hulls has been investigated in this study. The possibility of using the radial diffusion method based on software measurement of the rings area has also been investigated in this study. The software based method in radial diffusion method showed a higher r2 (0.995) value when compared to the traditional method. Irradiation reduced the tannin content ( Ppistachio hull extracts but increased the total phenolic content ( Ppistachio hull. Irradiation decreased the digestion rate of the pistachio hull at the dose of 40 kGy when compared to the control. This study showed that gamma irradiation decreased tannin and antioxidants activity of pistachio hull.

  8. Ship Creek bioassessment investigations

    Energy Technology Data Exchange (ETDEWEB)

    Cushing, C.E.; Mueller, R.P.; Murphy, M.T.

    1995-06-01

    Pacific Northwest Laboratory (PNL) was asked by Elmendorf Air Force Base (EAFB) personnel to conduct a series of collections of macroinvertebrates and sediments from Ship Creek to (1) establish baseline data on these populations for reference in evaluating possible impacts from Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) activities at two operable units, (2) compare current population indices with those found by previous investigations in Ship Creek, and (3) determine baseline levels of concentrations of any contaminants in the sediments associated with the macroinvertebrates. A specific suite of indices established by the US Environmental Protection Agency (EPA) was requested for the macroinvertebrate analyses; these follow the Rapid Bioassessment Protocol developed by Plafkin et al. (1989) and will be described. Sediment sample analyses included a Microtox bioassay and chemical analysis for contaminants of concern. These analyses included, volatile organic compounds, total gasoline and diesel hydrocarbons (EPA method 8015, CA modified), total organic carbon, and an inductive-coupled plasma/mass spectrometry (ICP/MS) metals scan. Appendix A reports on the sediment analyses. The Work Plan is attached as Appendix B.

  9. ERDC Ship/Tow Simulator

    Data.gov (United States)

    Federal Laboratory Consortium — Performing Advanced Hydrodynamic ModelingEngineers and ship pilots can now overcome the challenges of evaluating navigation channel designs, modifications and safety...

  10. CYTOTOXIC AND ANTIOXIDANT ACTIVITY OF BUCKWHEAT HULL EXTRACTS

    Directory of Open Access Journals (Sweden)

    Martina Danihelová

    2013-02-01

    Full Text Available Buckwheat contains many prophylactic compounds that are concentrated mainly in outer layers of buckwheat grain. The aim of this study was to prepare buckwheat hull extracts. Ten buckwheat cultivars were screened for their antioxidant and anticancer properties. Total polyphenol content was determined using Folin-Ciocalteau's reagent. Antioxidant activity was established by the method of binding free radical DPPH. Cytotoxic properties were measured on human cervical cancer cells HeLa using mitochondrial cytotoxic test (MTT. Total polyphenol content ranged from 166.67 to 635.31 mg GAE/100 g DW. The highest content displayed tartary buckwheat cultivar Madawaska (0.64% of hulls weight. Among common buckwheat the richest in polyphenols were cultivars Bamby and KASHO-2. The best free radical binding antioxidant activity was found for cultivars with highest polyphenol content. This relationship was not observed for cytotoxic action on human cervical cancer cells. The best growth inhibitory activity on HeLa cancer cells displayed common buckwheat cultivars Bamby and KASHO-2 (up to 50%, extract concentration 100 µg/ml. This was not found for tartary buckwheat cultivar Madawaska.

  11. Methylene blue adsorption from aqueous solution by dehydrated peanut hull

    Energy Technology Data Exchange (ETDEWEB)

    Ozer, Dursun [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey); Dursun, Guelbeyi [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey)]. E-mail: gdursun@firat.edu.tr; Ozer, Ahmet [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey)

    2007-06-01

    Dyes are colour organic compounds which can colorize the other substances. These substances usually presents in the effluent water of many industries, such as textiles, leather, paper, printing and cosmetics. To observe the potential feasibility of removing colour, peanut hull as an agricultural by-product was dehydrated with sulphuric acid (DPH) and used for adsorption of methylene blue (MB) from aqueous solution. The effects of various parameters such as initial methylene blue concentrations, temperatures and particle sizes were examined and optimal experimental conditions were determined. Adsorption data were well described by the Langmuir model, although they could be modelled by the Freundlich model as well. The adsorption process followed the pseudo-second order kinetic model. The mass transfer model as intraparticle diffusion was applied to the experimental data to examine the mechanisms of rate controlling step. It was found that at the higher initial MB concentration, intraparticle diffusion is becoming significant controlling step. The thermodynamic constants of the adsorption process were also evaluated by using the Langmuir constants related to the equilibrium of adsorption at different temperatures. The results in this study indicated that dehydrated peanut hull was a good adsorbent for removing methylene blue.

  12. The role of Bh4 in parallel evolution of hull colour in domesticated and weedy rice.

    Science.gov (United States)

    Vigueira, C C; Li, W; Olsen, K M

    2013-08-01

    The two independent domestication events in the genus Oryza that led to African and Asian rice offer an extremely useful system for studying the genetic basis of parallel evolution. This system is also characterized by parallel de-domestication events, with two genetically distinct weedy rice biotypes in the US derived from the Asian domesticate. One important trait that has been altered by rice domestication and de-domestication is hull colour. The wild progenitors of the two cultivated rice species have predominantly black-coloured hulls, as does one of the two U.S. weed biotypes; both cultivated species and one of the US weedy biotypes are characterized by straw-coloured hulls. Using Black hull 4 (Bh4) as a hull colour candidate gene, we examined DNA sequence variation at this locus to study the parallel evolution of hull colour variation in the domesticated and weedy rice system. We find that independent Bh4-coding mutations have arisen in African and Asian rice that are correlated with the straw hull phenotype, suggesting that the same gene is responsible for parallel trait evolution. For the U.S. weeds, Bh4 haplotype sequences support current hypotheses on the phylogenetic relationship between the two biotypes and domesticated Asian rice; straw hull weeds are most similar to indica crops, and black hull weeds are most similar to aus crops. Tests for selection indicate that Asian crops and straw hull weeds deviate from neutrality at this gene, suggesting possible selection on Bh4 during both rice domestication and de-domestication. © 2013 The Authors. Journal of Evolutionary Biology © 2013 European Society For Evolutionary Biology.

  13. Non-destructive assay of leached hulls in a nuclear fuel reprocessing plant

    International Nuclear Information System (INIS)

    Hofstetter, K.J.; Henderson, B.C.; Gray, J.H.; Huff, G.A.

    1978-01-01

    The hull monitor at the Barnwell Nuclear Fuels Plant (BNFP) will be a remotely controlled, fully automated system designed to quantitatively assay leached hulls for undissolved U and Pu. The hull monitor will assay the hulls from one metric ton of fuel per dissolver basket with the design goal of detecting 0.1% undissolved fuel and yet remain within the framework of the BNFP materials flow of five hull baskets per day. The non-destructive assay will be accomplished using a computer-based gamma-ray pulse height analysis system employing a 5 x 5 inch NaI(Tl) scintillation detector. The intense radiations from the fission product isotopes and the activation product isotopes produced in the reactor prevent direct assay of the undissolved fuel left in the hulls. The measurement will be made indirectly by demonstrating a correlation between the amount of 144 Ce undissolved and the remaining U. The isotope 144 Ce is a direct fission product with high cumulative yield. The daughter isotope 144 Pr has a gamma ray at 2.18 MeV well above other predominant radiations in the spectrum from the major interferences 60 Co, 58 Co, 95 Zr( 95 Nb), 137 Cs and 106 Ru( 106 Rh). Segmented scanning operation of the hull monitor is accomplished by rotation and vertical transversal of the hulls container past the detector station. Proper collimation and absorbers are required to maximize the 144 Ce( 144 Pr) to background ratio. A basket indexer is provided which monitors the scanning rate and ensures repositioning. The leached hull monitor system will be interfaced to a computer-based multichannel analyzer for ease of operation and data handling. A calibration basket has been fabricated to accomodate radioactive sources and inactive Zircaloy hulls

  14. DETERMINATION OF RELEVANT FEATURES OF A SCALE MODEL FOR A 55 000 DWT BULK CARRIER NECESSARY TO STUDY THE SHIP MANEUVERABILITY

    Directory of Open Access Journals (Sweden)

    ALECU TOMA

    2016-06-01

    Full Text Available The study method of a ship behavior based on practical tests on scale models is widely used both leading scientists and engineers, architects and researchers in the naval field. In this paper we propose to determine the parameters of a ship handling characteristics relevant to study the 55,000 dwt bulk carrier using a scale model. Scientific background for practical experimentation of this techniques necessary to built a scale model ship consists in applying the principles of similarity or "similitude". The scale model achieved by applying the laws of similarity must allow, through approximations available in certain circumstances, finding relevant parameters needed to simplify and solve the Navier-Stokes equations. These parameters are necessary for modeling the interaction between hull of the real ship and the fluid motion.

  15. Sensors Systems for the Automation of Operations in the Ship Repair Industry

    Science.gov (United States)

    Navarro, Pedro Javier; Muro, Juan Suardíaz; Alcover, Pedro María; Fernández-Isla, Carlos

    2013-01-01

    Hull cleaning before repainting is a key operation in the maintenance of ships. For years, a method to improve such operation has been sought by means of the robotization of techniques such as grit blasting and ultra high pressure water jetting. Despite this, it continues to be standard practice in shipyards that this process is carried out manually because the developed robotized systems are too expensive to be widely accepted by shipyards. We have chosen to apply a more conservative and realistic approach to this problem, which has resulted in the development of several solutions that have been designed with different automation and operation range degrees. These solutions are fitted with most of the elements already available in many shipyards, so the installation of additional machinery in the workplace would not be necessary. This paper describes the evolutionary development of sensor systems for the automation of the preparation process of ship hull surfaces before the painting process is performed. Such evolution has given rise to the development of new technologies for coating removal. PMID:24064601

  16. On Impact Mechanics in Ship Collisions

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup; Zhang, Shengming

    1998-01-01

    The purpose of this paper is to present analytical, closed-form expressions for the energy released for crushing and the impact impulse during ship collisions. Ship-ship collisions, ship collisions with rigid walls and ship collisions with flexible offshore structures are considered. The derived ...

  17. Luggage and shipped goods

    International Nuclear Information System (INIS)

    Vogel, H.; Haller, D.

    2007-01-01

    Summary: Purpose: Control of luggage and shipped goods are frequently carried out. The possibilities of X-ray technology shall be demonstrated. Materials and methods: There are different imaging techniques. The main concepts are transmission imaging, backscatter imaging, computed tomography, and dual energy imaging and the combination of different methods The images come from manufacturers and personal collections. Results: The search concerns mainly, weapons, explosives, and drugs; furthermore animals, and stolen goods, Special problems offer the control of letters and the detection of Improvised Explosive Devices (IED). Conclusion: One has to expect that controls will increase and that imaging with X-rays will have their part. Pattern recognition software will be used for analysis enforced by economy and by demand for higher efficiency - man and computer will produce more security than man alone

  18. Global Shipping Game

    Science.gov (United States)

    2011-01-28

    information please contact the Chairman, War Gaming Department, Naval War College, 686 Cushing Road, Newport, RI 02841 or via electronic mail at... Game ……………………………………………...9 c. Overarching Research Question……………………………………………..…10 d. Subsidiary Questions…………………………………………………………...10 e ...An e -SLOC is the “cyber network that supports the global maritime trade network.” Industry Global Shipping Game Report 27 experts felt that

  19. Single liner shipping service design

    DEFF Research Database (Denmark)

    Plum, Christian Edinger Munk; Pisinger, David; Salazar-González, Juan-José

    2014-01-01

    The design of container shipping networks is an important logistics problem, involving assets and operational costs measured in billions of dollars. To guide the optimal deployment of the ships, a single vessel round trip is considered by minimizing operational costs and flowing the best paying...

  20. Towards a nuclear merchant ship

    International Nuclear Information System (INIS)

    Nicholson, R.L.R.; Llewelyn, G.I.W.; Farmer, A.A.

    1976-01-01

    The operation of nuclear merchant ships is likely to be attended by a number of constraints and requirements. Not all of these can be fully resolved until such ships come into use and the necessary experience and confidence have been acquired. But the timing of commercial introduction, if it comes about, will depend on the relative economics of nuclear versus fossil fuel propulsion, and the differences in turn depend in part on the operating costs particular to nuclear ships. A review of operation aspects is essential not only to commercial appraisal; each country whose trade may be carried in nuclear ships - whether it will build such ships or not - will have occasion to give some attention to the problems. It is an international problem and is, as noted later, being considered internationally. This paper; i) reviews some of the operational aspects as seen in the U.K.; ii) summarizes views received by the Nuclear Merchant Ship Unit (NMSU) from U.K. shipping, shipbuilding and nuclear industries on the prospects of a U.K. nuclear merchant ship. (author)

  1. Ship exhaust gas plume cooling

    NARCIS (Netherlands)

    Schleijpen, H.M.A.; Neele, P.P.

    2004-01-01

    The exhaust gas plume is an important and sometimes dominating contributor to the infrared signature of ships. Suppression of the infrared ship signatures has been studied by TNO for the Royal Netherlands Navy over considerable time. This study deals with the suppression effects, which can be

  2. Navy Hospital ships in history

    Directory of Open Access Journals (Sweden)

    Sougat Ray

    2017-01-01

    Full Text Available Hospital ships are operated by the Naval forces in or near war zones to provide medical assistance to the wounded personnel of all nationalities and not be used for any military purpose. Hospital ships possibly existed in ancient times and the Athenian Navy had a ship named Therapia. However, it was only during the 17th century that it became a common practice for the naval squadrons to be accompanied by large ships with the facilities of carrying the wounded after each engagement. In 1860, the steamships HMS Melbourne and HMS Mauritius were equipped with genuine medical facilities. They were manned by the Medical Staff Corps and provided services to the British expedition to China. During the World War I and World War II, passenger ships were converted for use as hospital ships and were started to be used on a massive scale. RMS Aquitania and HMHS Britannic were two famous examples of hospital ships used extensively. Modern US hospital ships USNS Mercy and USNS Comfort are operated by Military Sealift Command of the US Navy. Their primary mission is to provide emergency on-site care for US combatant forces deployed in war or other operations.

  3. Identification of Dynamically Positioned Ships

    Directory of Open Access Journals (Sweden)

    Thor I. Fossen

    1996-04-01

    Full Text Available Todays model-based dynamic positioning (DP systems require that the ship and thruster dynamics are known with some accuracy in order to use linear quadratic optical control theory. However, it is difficult to identify the mathematical model of a dynamically posititmed (DP ship since the ship is not persistently excited under DP. In addition the ship parameter estimation problem is nonlinear and multivariable with only position and thruster state measurements available for parameter estimation. The process and measurement noise must also be modeled in order to avoid parameter drift due to environmental disturbances and sensor failure. This article discusses an off-line parallel extended Kalman filter (EKF algorithm utilizing two measurement series in parallel to estimate the parameters in the DP ship model. Full-scale experiments with a supply vessel are used to demonstrate the convergence and robustness of the proposed parameter estimator.

  4. A Study on the Radioactivity Reduction Method for the Decladding Hull

    International Nuclear Information System (INIS)

    Kim, Jong Ho; Jung, In Ha; Park, Jang Jin; Shin, Jin Myeong; Lee, Ho Hee; Yang, Myung Seung

    1994-01-01

    The cladding materials remaining after reprocessing process of the nuclear fuel, generally called as hulls, are classified as a high-level radioactive waste. They are usually packaged in the container for disposal after being compacted, melted, or solidified into the matrix. The efforts to fabricated a better ingot for a more favorable disposal to the environment have failed due to the technical difficulties encountered in the chemical decontamination method. In the early 1990s, the accumulation of radio-chemical data on hulls and the advent of new technology such as a laser or plasma have made the pre-treatment of the hulls mere efficient. This paper summarizes the information regarding the radio-chemical analysis of the hull through a literature survey and determines the characteristics of the hull and depth profile of the radio-nuclides within the hull thickness. The feasibility study was carried out to evaluate the reduction of the radioactivity by peeling off the surface of the hull with the application of laser technology

  5. Solid-state fermentation of Mortierella isabellina for lipid production from soybean hull.

    Science.gov (United States)

    Zhang, Jianguo; Hu, Bo

    2012-02-01

    Soybean hull, generated from soybean processing, is a lignocellulosic material with limited industrial applications and little market value. This research is exploring a new application of soybean hull to be converted to fungal lipids for biodiesel production through solid-state fermentation. Mortierella isabellina was selected as the oil producer because of its high lipid content at low C/N ratio. Several cultivation factors were investigated, including moisture content, inoculums size, fungal spore age, and nutrient supplements, in an attempt to enhance the lipid production of the solid-state fermentation process. The results showed that lipid production with the increase of the moisture content and the spore age, while decreased as the size of inoculums increased. Nutrients addition (KH₂PO₄ 1.2 mg and MgSO₄ 0.6 mg/g soybean hull) improved the lipid production. The total final lipid reached 47.9 mg lipid from 1 g soybean hull after the conversion, 3.3-fold higher than initial lipid reserve in the soybean hull. The fatty acid profile analysis indicated that fatty acid content consisted of 30.0% of total lipid, and 80.4% of total fatty acid was C16 and C18. Therefore, lipid production from soybean hull is a possible option to enable soybean hull as a new resource for biodiesel production and to enhance the overall oil production from soybeans.

  6. Antioxidant constituents of almond [Prunus dulcis (Mill.) D.A. Webb] hulls.

    Science.gov (United States)

    Takeoka, Gary R; Dao, Lan T

    2003-01-15

    Almond hulls (Nonpareil variety) were extracted with methanol and analyzed by reversed phase HPLC with diode array detection. The extract contained 5-O-caffeoylquinic acid (chlorogenic acid), 4-O-caffeoylquinic acid (cryptochlorogenic acid), and 3-O-caffeoylquinic acid (neochlorogenic acid) in the ratio 79.5:14.8:5.7. The chlorogenic acid concentration of almond hulls was 42.52 +/- 4.50 mg/100 g of fresh weight (n = 4; moisture content = 11.39%). Extracts were tested for their ability to inhibit the oxidation of methyl linoleate at 40 degrees C. At an equivalent concentration (10 microg/1 g of methyl linoleate) almond hull extracts had higher antioxidant activity than alpha-tocopherol. At higher concentrations (50 microg/1 g of methyl linoleate) almond hull extracts showed increased antioxidant activity that was similar to chlorogenic acid and morin [2-(2,4-dihydroxyphenyl)-3,5,7-trihydroxy-4H-1-benzopyran-4-one] standards (at the same concentrations). These data indicate that almond hulls are a potential source of these dietary antioxidants. The sterols (3beta,22E)-stigmasta-5,22-dien-3-ol (stigmasterol) and (3beta)-stigmast-5-en-3-ol (beta-sitosterol) (18.9 mg and 16.0 mg/100 g of almond hull, respectively) were identified by GC-MS of the silylated almond hull extract.

  7. Co-combustion of peanut hull and coal blends: Artificial neural networks modeling, particle swarm optimization and Monte Carlo simulation.

    Science.gov (United States)

    Buyukada, Musa

    2016-09-01

    Co-combustion of coal and peanut hull (PH) were investigated using artificial neural networks (ANN), particle swarm optimization, and Monte Carlo simulation as a function of blend ratio, heating rate, and temperature. The best prediction was reached by ANN61 multi-layer perception model with a R(2) of 0.99994. Blend ratio of 90 to 10 (PH to coal, wt%), temperature of 305°C, and heating rate of 49°Cmin(-1) were determined as the optimum input values and yield of 87.4% was obtained under PSO optimized conditions. The validation experiments resulted in yields of 87.5%±0.2 after three replications. Monte Carlo simulations were used for the probabilistic assessments of stochastic variability and uncertainty associated with explanatory variables of co-combustion process. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Combustion kinetics of hydrochar produced from hydrothermal carbonisation of Karanj (Pongamia pinnata) fruit hulls via thermogravimetric analysis.

    Science.gov (United States)

    Islam, Md Azharul; Kabir, G; Asif, M; Hameed, B H

    2015-10-01

    This study examined the combustion profile and kinetics of hydrochar produced from hydrothermal carbonisation (HTC) of Karanj fruit hulls (KFH). The HTC-KFH hydrochar combustion kinetics was investigated at 5, 10, and 20°C/min by thermogravimetric analysis. The kinetics model, Kissinger-Akahira-Sunose revealed the combustion kinetics parameters for the extent of conversion from 0.1 to 0.8; the activation energy varies from 114 to 67 kJ/mol respectively. The hydrochar combustion followed multi-steps kinetics; the Coats-Redfern models predicted the activation energies and pre-exponential constants for the hydrochar combustion zones. The diffusion models are the effective mechanism in the second and third zone. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Classification of Fusarium-Infected Korean Hulled Barley Using Near-Infrared Reflectance Spectroscopy and Partial Least Squares Discriminant Analysis

    Directory of Open Access Journals (Sweden)

    Jongguk Lim

    2017-09-01

    Full Text Available The purpose of this study is to use near-infrared reflectance (NIR spectroscopy equipment to nondestructively and rapidly discriminate Fusarium-infected hulled barley. Both normal hulled barley and Fusarium-infected hulled barley were scanned by using a NIR spectrometer with a wavelength range of 1175 to 2170 nm. Multiple mathematical pretreatments were applied to the reflectance spectra obtained for Fusarium discrimination and the multivariate analysis method of partial least squares discriminant analysis (PLS-DA was used for discriminant prediction. The PLS-DA prediction model developed by applying the second-order derivative pretreatment to the reflectance spectra obtained from the side of hulled barley without crease achieved 100% accuracy in discriminating the normal hulled barley and the Fusarium-infected hulled barley. These results demonstrated the feasibility of rapid discrimination of the Fusarium-infected hulled barley by combining multivariate analysis with the NIR spectroscopic technique, which is utilized as a nondestructive detection method.

  10. Evaluation of management alternatives for LWR hulls and caps

    International Nuclear Information System (INIS)

    Chaudon, L.; Mehling, O.; Cecille, L.; Thiels, G.; Kowa, S.

    1993-01-01

    Hulls and caps resulting from the reprocessing of LWR spent fuels represent one of the major sources of alpha-bearing solid waste generated during the nuclear fuel cycle. The Commission of the European Communities has undertaken considerable R and D efforts on the development of advanced treatment and conditioning methods for this type of waste. In view of the encouraging results achieved, the Commission launched a theoretical assessment study on cladding waste management. Six practical or potential schemes were identified and elaborated: direct cementation, decontamination prior to cementation, rolling before cementation, rolling followed by embedding in graphite, compaction, and melting in a cold crucible. The economic aspects of each management option were also investigated. This included the assessment of the plant (treatment, conditioning and interim storage), transport and disposal costs. Further consideration will be required to define the best management option for 'cap' wastes. Transport and disposal costs will also require further analysis from an industrial standpoint

  11. Conversion of rice hull ash into soluble sodium silicate

    Directory of Open Access Journals (Sweden)

    Edson Luiz Foletto

    2006-09-01

    Full Text Available Sodium silicate is used as raw material for several purposes: silica gel production, preparation of catalysts, inks, load for medicines, concrete hardening accelerator, component of detergents and soaps, refractory constituent and deflocculant in clay slurries. In this work sodium silicate was produced by reacting rice hull ash (RHA and aqueous sodium hydroxide, in open and closed reaction systems. The studied process variables were time, temperature of reaction and composition of the reaction mixture (expressed in terms of molar ratios NaOH/SiO2 and H2O/SiO2. About 90% silica conversion contained in the RHA into sodium silicate was achieved in closed system at 200 °C. The results showed that sodium silicate production from RHA can generate aggregate value to this residue.

  12. Methods of conditioning waste fuel decladding hulls and dissolver residues

    International Nuclear Information System (INIS)

    De Regge, P.; Loida, A.; Schmidt-Hansberg, T.; Sombret, C.

    1985-01-01

    Several methods for conditioning spent fuel decladding hulls or dissolver residues have been considered in various countries of the European Community. Five of these methods used embedding technique with or without prior compaction: they are based on incorporation in metallic alloys, glass, ceramics, cements and metals or graphite compounds. A sixth one consists in melting the decladding materials. The corresponding research programmes have been pursued to varying states of progress with regard to demonstrating their feasibility on an industrial scale and the use of genuine wastes in bench scale experiments. The properties of the conditioned wastes have been investigated. Special attention has been paid to the corrosion resistance to various aqueous media as tap water, brine or clayey water. Although no categorical conclusion can be drawn from the initial results, the available findings provide a basis for assessing the different processes

  13. Consideration on longitudinal bending moment in waves of a large high-speed ship; Ogata kosokutei no haro tatemage moment ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Deguchi, M; Takimoto, T; Kasuda, T; Tozawa, S [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1996-04-10

    While high-speed ships are on a trend of increased speed, size and diversity, one of the most important items is a discussion on large high-speed ships with a total length of 100 m class on their longitudinal strength in waves. With such a background, a model ship intended of realizing a large high-speed was assumed, and verification of reliability in structural strength and establishment of a design method for this ship were intended. Therefore, oceanographic condition setting, design load setting, FEM analysis, and strength assessment were carried out. This paper reports the results of comparison with and consideration on conventional criteria and linear calculations, mainly the results of simulated calculations on non-linear hull movement/wave load which have been performed in discussing the loads. The result of the non-linear simulation is thought to have well simulated non-linearity characteristic to the ship. Conventional criteria which have been arranged on the record of use for small ships are considered impossible to be applied to large high-speed ships. Under such a situation, the simplified equations by Kaneko et al are judged effective in making an initial plan for this type of ship. 6 refs., 7 figs., 2 tabs.

  14. Optimization of the ship type using waveform by means of Rankine source method; Rankine source ho ni yoru hakei wo mochiita funagata saitekika ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Hirayama, A; Eguchi, T [Mitsui Engineering and Shipbuilding Co. Ltd., Tokyo (Japan)

    1996-04-10

    Among the numerical calculation methods for steady-state wave-making problems, the panel shift Rankine source (PSRS) method has the advantages of rather precise determination of wave pattern of practical ship types, and short calculation period. The wave pattern around the hull was calculated by means of the PSRS method. The waveform analysis was carried out for the wave, to obtain an amplitude function of the original ship type. Based on the amplitude function, a ship type improvement method aiming at the optimization of ship type was provided using a conditional calculus of variation. A Series 60 (Cb=0.6) ship type was selected for the ship type improvement, to apply this technique. It was suggested that optimum design can be made for reducing the wave making resistance by means of this method. For the improvement of Series 60 ship type using this method, a great degree of reduction in the wave making resistance was recognized from the results of numerical waveform analysis. It was suggested that the ship type improvement aiming at the reduction of wave-making resistance can be made in shorter period and by smaller labor compared with the method using a waveform analysis of cistern tests. 5 refs., 9 figs.

  15. Immobilization of Saccharomyces Cerevisiae in Rice Hulls for Ethanol Production

    Directory of Open Access Journals (Sweden)

    Edita Martini

    2011-05-01

    Full Text Available The whole cell immobilization in ethanol fermentation can be done by using natural carriers or through synthetic carriers. All of these methods have the same purpose of retaining high cell concentrations within a certain defined region of space which leads to higher ethanol productivity. Lignocellulosic plant substance represents one of highly potential sources in ethanol production. Some studies have found that cellulosic substances substances can also be used as a natural carrier in cell immobilization by re-circulating pre-culture medium into a reactor. In this experiment, rice hulls without any treatment were used to immobilize Saccharomyces cerevisiae through semi solid state incubation combined with re-circulating pre-culture medium. The scanning electron microscopy (SEM pictures of the carrier show that the yeast cells are absorbed and embedded to the rice hull pore. In liquid batch fermentation system with an initial sugar concentration of 50 g/L, nearly 100% total sugar was consumed after 48 hours. This resulted in an ethanol yield of 0.32 g ethanol/g glucose, which is 62.7% of the theoretical value. Ethanol productivity of 0.59 g/(L.h is 2.3 fold higher than that of free cells which is 0.26 g/(L.h. An effort to reuse the immobilized cells in liquid fermentation system showed poor results due to cell desorption in the first batch which led to high sugar concentration inhibitory effect in the second batch fermentation. This might be solved by using semi solid fermentation process in the future work.

  16. Decontamination of fast reactor hulls and properties of immobilised waste forms

    International Nuclear Information System (INIS)

    Biddle, P.; Brown, P.E.; Rees, J.H.

    1984-01-01

    The objectives of this contract are threefold: (i) to characterise the activities associated with genuine hulls generated in reprocessing fuel from the Prototype Fast Reactor; (ii) to examine the feasibility of decontaminating the hulls by the use of simple low-temperature techniques; and (iii) to immobilise the hulls in cement and evaluate the products. Over the last year, work has concentrated in areas (i) and (ii), but the balance of the programme is now shifting more towards topic (iii). Progress is reported. (author)

  17. Cybersecurity Framework for Ship Industrial Control System

    OpenAIRE

    Maule, R. William; Hake, Joseph

    2016-01-01

    Ship mechanical and electrical control systems, and the communications grid through which these devices operate, are a high priority concern for Navy leadership. Ship systems use microprocessor-based controls to interface with physical objects, and Programmable Logic Controllers (PLCs) to automate ship electromechanical processes. Ship operations are completely dependent on these devices. The commercial security products upon which ships depend do not work on ICS, leaving ships vulnerable. Th...

  18. Risk-informed optimal routing of ships considering different damage scenarios and operational conditions

    International Nuclear Information System (INIS)

    Decò, Alberto; Frangopol, Dan M.

    2013-01-01

    The aim of this paper is the development of a risk-informed decision tool for the optimal mission-oriented routing of ships. The strength of the hull is investigated by modeling the midship section with finite elements and by analyzing different damage levels depending on the propagation of plastification throughout the section. Vertical and horizontal flexural interaction is investigated. Uncertainties associated with geometry and material properties are accounted for by means of the implementation of the response surface method. Load effects are evaluated using strip theory. Reliability analysis is performed for several ship operational conditions and considering four different limit states. Then, risk is assessed by including the direct losses associated with five investigated damage states. The effects of corrosion on aged ships are included in the proposed approach. Polar representation of load effects, reliability, and direct risk are presented for a large spectrum of operational conditions. Finally, the optimal routing of ships is obtained by minimizing both the estimated time of arrival and the expected direct risk, which are clearly conflicting objectives. The optimization process provides feasible solutions belonging to the Pareto front. The proposed approach is applied to a Joint High Speed Sealift

  19. Containment of spills from ships

    International Nuclear Information System (INIS)

    Engerer, M.J.

    1992-01-01

    Oil escaping from a ship is contained within a limited area surrounding the ship by means of a flexible ring structure. The ring structure is stored in a collapsed state in a compartment extending around the ship. In response to an oil spill, the ring structure is dropped from the compartment and immediately surrounds the ship. A circular inflatable flotation section of the ring structure is charged with gas under pressure. The gas is supplied from a bottle cascade aboard the ship, through lines preconnected to the flotation section and paid out from free-wheeling reels. The flotation section supports a thin circumferential wall of predetermined height that submerges and assumes a vertical cylinder-like shape surrounding the escaping oil. The oil floats within the confines of the ring structure, and the ring structure is progressively expanded to a predetermined size selected to accommodate the total volume of oil carried by the ship. When the ring structure achieves its expanded state, pressure in the flotation section is raised to render the structure relatively rigid and resistant to collapse in response to wave action. Oil can be removed from the interior of the ring structure by recovery ships using suction lines or other conventional recovery methods. 12 figs

  20. Ships and the Sailors Inside Them

    National Research Council Canada - National Science Library

    Sims, Philip

    2004-01-01

    .... Iron shipbuilding allowed safer and healthier ships but their internal compartmentation created communication problems which were gradually solved with mechanical systems Ships developed their own...