Radiocarbon dating of large termite mounds of the miombo woodland of Katanga, DR Congo

Science.gov (United States)

Erens, Hans; Boudin, Mathieu; Mees, Florias; Dumon, Mathijs; Mujinya, Basile; Van Strydonck, Mark; Baert, Geert; Boeckx, Pascal; Van Ranst, Eric

2015-04-01

The miombo woodlands of South Katanga (D.R. Congo) are characterized by a high spatial density of large conic termite mounds built by Macrotermes falciger (3 to 5 ha-1, ~5 m high, ~15 m in diameter). The time it takes for these mounds to attain this size is still largely unknown. In this study, the age of four of these mounds is determined by 14C-dating the acid-insoluble organic carbon fraction of samples taken along the central vertical axis of two active and two abandoned mounds. The age sequence in the active mounds is erratic, but the results for the abandoned mounds show a logical increase of 14C-age with depth. The ages measured at 50 cm above ground level were 2335 - 2119 cal yr BP for the large abandoned mound (630 cm high), and 796 - 684 cal yr BP for the small abandoned mound (320 cm high). Cold-water-extractable organic carbon (CWEOC) measurements combined with spectroscopic analysis revealed that the lower parts of the active mounds may have been contaminated with recent carbon that leached from the active nest. Nonetheless, this method appears to provide reliable age estimates of large, abandoned termite mounds, which are older than previously estimated. Furthermore, historical mound growth rates seem to correspond to past temperature changes, suggesting a relation between past environmental conditions and mound occupancy. Keywords : 14C, water-extractable carbon, low-temperature combustion

Calibration for plutonium-238 lung counting at Mound Laboratory

International Nuclear Information System (INIS)

Tomlinson, F.K.

1976-01-01

The lung counting facility at Mound Laboratory was calibrated for making plutonium-238 lung deposition assessments in the fall of 1969. Phoswich detectors have been used since that time; however, the technique of calibration has improved considerably. The current technique of calibrating the lung counter is described as well as the method of error analysis and determination of the minimum detectable activity. A Remab hybrid phantom is used along with an attenuation curve which is derived from plutonium loaded lungs and ground beef absorber measurements. The errors that are included in an analysis as well as those that are excluded are described. The method of calculating the minimum detectable activity is also included

The Bahrain Burial Mound Project

DEFF Research Database (Denmark)

Laursen, Steffen; Johansen, Kasper Lambert

2007-01-01

the majority of burial mounds have been removed to make way for roads and housing, and in this process about 8000 mounds have been excavated; of these only c. 265 have been published. In 2006 the Bahrain Directorate for Culture & National Heritage and Moesgaard Museum decided on a collaborative project...... process of linking relevant information to the mounds have been initiated in the course of which excavation data of individual monument is being fed into a relational database. Our preliminary study of the digital maps of the mound cemeteries has revealed an abundance of interesting patterns...... that immediately gave rise to puzzling new questions that will direct the future explorations of the project. Of particular interest is a distinctive new type of elite monuments situated to the south of the so-called Royal Mounds in the centre of the island. The newly discovered type of mounds apparently reflect...

Variability of soil properties within large termite mounds in South Katanga, DRC - origins and applications.

Science.gov (United States)

Erens, Hans; Bazirake Mujinya, Basile; Boeckx, Pascal; Baert, Geert; Mees, Florias; Van Ranst, Eric

2014-05-01

The miombo woodlands of South Katanga (D.R. Congo) are characterized by a high spatial density of large conic termite mounds built by Macrotermes falciger (3 to 5 ha-1). With an average height of 5.05 m and diameter of 14.88 m, these are some of the largest biogenic structures in the world. The mound material is known to differ considerably from the surrounding Ferralsols. Specifically, mound material exhibits a finer texture, higher CEC and exchangeable basic cation content, lower organic matter content, and an accumulation of phosphorous, nitrate and secondary carbonates. However, as demonstrated by the present study, these soil properties are far from uniform within the volume of the mound. The termites' nesting and foraging activity, combined with pedogenic processes over extended periods of time, generates a wide range of physical, chemical, and biological conditions in different parts of the mound. Analysis of samples taken along a cross-section of a large active mound allowed generating contour plots, thus visualizing the variability of soil properties within the mound. The central columns of three other mounds were sampled to confirm apparent trends. The contour plots show that the mounds comprise four functional zones: (i) the active nest, found at the top; (ii) an accumulation zone , in more central parts of the mound; (iii) a dense inactive zone, surrounding the accumulation zone and consisting of accumulated erosion products from former active nests; and (iv) the outer mantle, characterized by intense varied biological activity and by a well-developed soil structure. Intermittent leaching plays a key role in explaining these patterns. Using radiocarbon dating, we found that some of these mounds are at least 2000 years old. Their current size and shape is likely the result of successive stages of erosion and rebuilding, in the course of alternating periods of mound abandonment and recolonization. Over time, termite foraging combined with limited leaching

Elimination of the Mound-Building Termite, Nasutitermes exitiosus (Isoptera: Termitidae) in South-Eastern Australia Using Bistrifluron Bait.

Science.gov (United States)

Webb, Garry A; Mcclintock, Charles

2015-12-01

Bistrifluron, a benzoylphenylurea compound, was evaluated for efficacy against Nasutitermes exitiosus (Hill), a mound-building species in southern Australia. Bistrifluron bait (trade name Xterm) was delivered as containerized pellets inserted into plastic feeding stations implanted in the sides of mounds-60 g for bistrifluron bait-treated mounds and 120 g of blank bait for untreated mounds. Termites actively tunneled in the gaps between pellets and removed bait from the canisters. All five treated mounds were eventually eliminated, and all five untreated mounds remained active at the end of the trial. Four of the five treated mounds were considered dead and excavated after 26 wk, but there were earlier signs of mound distress-reduced repair of experimental casement damage and reduced activity in bait canisters by 22 wk and reduced internal mound temperature after 11 wk. One treated mound showed activity in the bait station right through until almost the end of the trial (47 wk), but excavation at 49 wk showed no further activity in the mound. The five untreated colonies removed on average 97% of blank bait offered, while the five treated colonies removed on average 39.1% of bait offered. There was a wide variation in temperature profiles of mounds (up to 15°C for both minimum and maximum internal temperatures), from the beginning of the trial and even before the effects of baiting were evident. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Soil Physical and Chemical Properties in Epigeal Termite Mounds in Pastures

Directory of Open Access Journals (Sweden)

Sandra Santana de Lima

2018-03-01

Full Text Available ABSTRACT We characterized soil physical and chemical properties and soil organic matter in epigeal termite mounds in pastures to evaluate the changes promoted by termites in comparison to an adjacent area. We selected seven active epigeal termite mounds in the municipality of Seropédica, state of Rio de Janeiro, Brazil. Soil samples were collected from top, center and base positions of each mound, at 0.50 and 1.50 m distance from the base of the mound. We identified individuals of the genus Embiratermes, Velocitermes, and Orthognathotermes. The humin fraction predominated over the humic and fulvic acid fractions both in mounds and adjacent soil. The amount of organic matter and the mineral fractions (mineral-associated organic carbon - MOC varied among builder species. The studied chemical attributes point to a higher concentration of nutrients in the mounds than in the adjacent soil.

A national biomedical tracer facility (NBTF)

International Nuclear Information System (INIS)

Erb, D.E.; Moody, D.; Peterson, E.; Mausner, L.; Atcher, R.

1991-01-01

The production, supply, and sale of isotopes and related services originating in Department of Energy production and research facilities has been a long-standing activity of DOE and predecessor organizations (AEC and ERDA). The authority for this activity is derived from the Atomic Energy Act of 1954, as amended. Stable isotopes and radioisotopes, together with related services, are now being produced in many DOE production and research facilities at several DOE installations which presently include: Argonne National Laboratory (ANL), Brookhaven National Laboratory (BNL), EG ampersand G Mound Laboratories (Mound), Idaho National Engineering Laboratory (INEL), Los Alamos National Laboratory (LANL), Oak Ridge National Laboratory (ORNL), Westinghouse Hanford Company (WHC), and the Pacific Northwest Laboratories (PNL) at Richland, Washington. The products and services are, in many instances, unique in that their production and processing can be performed only in production and research facilities owned by, and operated for, DOE. In some instances, DOE is the sole supplier of such isotope products and services in the Western World

Thermoregulation and ventilation of termite mounds

Science.gov (United States)

Korb, Judith

2003-05-01

Some of the most sophisticated of all animal-built structures are the mounds of African termites of the subfamily Macrotermitinae, the fungus-growing termites. They have long been studied as fascinating textbook examples of thermoregulation or ventilation of animal buildings. However, little research has been designed to provide critical tests of these paradigms, derived from a very small number of original papers. Here I review results from recent studies on Macrotermes bellicosus that considered the interdependence of ambient temperature, thermoregulation, ventilation and mound architecture, and that question some of the fundamental paradigms of termite mounds. M. bellicosus achieves thermal homeostasis within the mound, but ambient temperature has an influence too. In colonies in comparably cool habitats, mound architecture is adapted to reduce the loss of metabolically produced heat to the environment. While this has no negative consequences in small colonies, it produces a trade-off with gas exchange in large colonies, resulting in suboptimally low nest temperatures and increased CO2 concentrations. Along with the alteration in mound architecture, the gas exchange/ventilation mechanism also changes. While mounds in the thermally appropriate savannah have a very efficient circular ventilation during the day, the ventilation in the cooler forest is a less efficient upward movement of air, with gas exchange restricted by reduced surface exchange area. These results, together with other recent findings, question entrenched ideas such as the thermosiphon-ventilation mechanism or the assumption that mounds function to dissipate internally produced heat. Models trying to explain the proximate mechanisms of mound building, or building elements, are discussed.

Mound's decommissioning experience, tooling, and techniques

International Nuclear Information System (INIS)

Combs, A.B.; Davis, W.P.; Elswick, T.C.; Garner, J.M.; Geichman, J.R.

1982-01-01

Monsanto Research Corporation (MRC), which operates Mound for the Department of Energy (DOE), has been decommissioning radioactively contaminated facilities since 1949. We are currently decommissioning three plutonium-238 contaminated facilities (approximately 50,000 ft 2 ) that contained 1100 linear ft of gloveboxes; 900 linear ft of conveyor housing; 2650 linear ft of dual underground liquid waste lines; and associated contaminated piping, services, equipment, structures, and soil. As of June 1982, over 29,000 Ci of plutonium-238 have been removed in waste and scrap residues. As a result of the current and previous decommissioning projects, valuable experience has been gained in tooling and techniques. Special techniques have been developed in planning, exposure control, contamination control, equipment removal, structural decontamination, and waste packaging

Crater Mound Formation by Wind Erosion on Mars

Science.gov (United States)

Steele, L. J.; Kite, E. S.; Michaels, T. I.

2018-01-01

Most of Mars' ancient sedimentary rocks by volume are in wind-eroded sedimentary mounds within impact craters and canyons, but the connections between mound form and wind erosion are unclear. We perform mesoscale simulations of different crater and mound morphologies to understand the formation of sedimentary mounds. As crater depth increases, slope winds produce increased erosion near the base of the crater wall, forming mounds. Peak erosion rates occur when the crater depth is ˜2 km. Mound evolution depends on the size of the host crater. In smaller craters mounds preferentially erode at the top, becoming more squat, while in larger craters mounds become steeper sided. This agrees with observations where smaller craters tend to have proportionally shorter mounds and larger craters have mounds encircled by moats. If a large-scale sedimentary layer blankets a crater, then as the layer recedes across the crater it will erode more toward the edges of the crater, resulting in a crescent-shaped moat. When a 160 km diameter mound-hosting crater is subject to a prevailing wind, the surface wind stress is stronger on the leeward side than on the windward side. This results in the center of the mound appearing to "march upwind" over time and forming a "bat-wing" shape, as is observed for Mount Sharp in Gale crater.

IODP Expedition 307 Drills Cold-Water Coral Mound Along the Irish Continental Margin

Directory of Open Access Journals (Sweden)

Trevor Williams

2006-03-01

Full Text Available Introduction Over the past decade, oceanographic and geophysical surveys along the slope of the Porcupine Seabight off the southwestern continental margin of Ireland have identified upwards of a thousand enigmatic mound-like structures (Figs. 1 and 2. The mounds of the Porcupine Seabight rise from the seafl oor in water depths of 600–900 m and formimpressive conical bodies several kilometers wide and up to 200 m high. Although a few mounds such as Thérèse Mound and Galway Mound are covered by a thriving thicket of coldwater corals, most mound tops and fl anks are covered by dead coral rubble or are entirely buried by sediment (De Mol et al., 2002; Fig. 2, Beyer et al., 2003. Lophelia pertusa (Fig.3 and Madrepora oculata are the most prominent cold-water corals growing without photosynthetic symbionts. The widespread discovery of large and numerous coral-bearing banks and the association of these corals with the mounds have generated signifi cant interest as to the composition, origin and development of these mound structures.Challenger Mound, in the Belgica mound province, has an elongated shape oriented along a north-northeast to south-southwest axis and ispartially buried under Pleistocene drift sediments. In high-resolution seismic profiles the mounds appear to root on an erosion surface (van Rooij et al., 2003. During IODP Expedition307 the Challenger Mound in the Porcupine Seabight was drilled with the goal of unveiling the origin and depositional processes withinthese intriguing sedimentary structures. Challenger Mound, unlike its near neighbors the Thérèse and Galway mounds, has little to no livecoral coverage and, therefore, was chosen as the main target for drilling activities, so that no living ecosystem would be disturbed.

Models of formation and activity of spring mounds in the mechertate-chrita-sidi el hani system, eastern Tunisia: implications for the habitability of Mars.

Science.gov (United States)

Essefi, Elhoucine; Komatsu, Goro; Fairén, Alberto G; Chan, Marjorie A; Yaich, Chokri

2014-08-28

Spring mounds on Earth and on Mars could represent optimal niches of life development. If life ever occurred on Mars, ancient spring deposits would be excellent localities to search for morphological or chemical remnants of an ancient biosphere. In this work, we investigate models of formation and activity of well-exposed spring mounds in the Mechertate-Chrita-Sidi El Hani (MCSH) system, eastern Tunisia. We then use these models to explore possible spring mound formation on Mars. In the MCSH system, the genesis of the spring mounds is a direct consequence of groundwater upwelling, triggered by tectonics and/or hydraulics. As they are oriented preferentially along faults, they can be considered as fault spring mounds, implying a tectonic influence in their formation process. However, the hydraulic pressure generated by the convergence of aquifers towards the surface of the system also allows consideration of an origin as artesian spring mounds. In the case of the MCSH system, our geologic data presented here show that both models are valid, and we propose a combined hydro-tectonic model as the likely formation mechanism of artesian-fault spring mounds. During their evolution from the embryonic (early) to the islet ("island") stages, spring mounds are also shaped by eolian accumulations and induration processes. Similarly, spring mounds have been suggested to be relatively common in certain provinces on the Martian surface, but their mode of formation is still a matter of debate. We propose that the tectonic, hydraulic, and combined hydro-tectonic models describing the spring mounds at MCSH could be relevant as Martian analogs because: (i) the Martian subsurface may be over pressured, potentially expelling mineral-enriched waters as spring mounds on the surface; (ii) the Martian subsurface may be fractured, causing alignment of the spring mounds in preferential orientations; and (iii) indurated eolian sedimentation and erosional remnants are common features on Mars

Models of Formation and Activity of Spring Mounds in the Mechertate-Chrita-Sidi El Hani System, Eastern Tunisia: Implications for the Habitability of Mars

Directory of Open Access Journals (Sweden)

Elhoucine Essefi

2014-08-01

Full Text Available Spring mounds on Earth and on Mars could represent optimal niches of life development. If life ever occurred on Mars, ancient spring deposits would be excellent localities to search for morphological or chemical remnants of an ancient biosphere. In this work, we investigate models of formation and activity of well-exposed spring mounds in the Mechertate-Chrita-Sidi El Hani (MCSH system, eastern Tunisia. We then use these models to explore possible spring mound formation on Mars. In the MCSH system, the genesis of the spring mounds is a direct consequence of groundwater upwelling, triggered by tectonics and/or hydraulics. As they are oriented preferentially along faults, they can be considered as fault spring mounds, implying a tectonic influence in their formation process. However, the hydraulic pressure generated by the convergence of aquifers towards the surface of the system also allows consideration of an origin as artesian spring mounds. In the case of the MCSH system, our geologic data presented here show that both models are valid, and we propose a combined hydro-tectonic model as the likely formation mechanism of artesian-fault spring mounds. During their evolution from the embryonic (early to the islet (“island” stages, spring mounds are also shaped by eolian accumulations and induration processes. Similarly, spring mounds have been suggested to be relatively common in certain provinces on the Martian surface, but their mode of formation is still a matter of debate. We propose that the tectonic, hydraulic, and combined hydro-tectonic models describing the spring mounds at MCSH could be relevant as Martian analogs because: (i the Martian subsurface may be over pressured, potentially expelling mineral-enriched waters as spring mounds on the surface; (ii the Martian subsurface may be fractured, causing alignment of the spring mounds in preferential orientations; and (iii indurated eolian sedimentation and erosional remnants are common

Environmental survey preliminary report, Mound Plant, Miamisburg, Ohio

Energy Technology Data Exchange (ETDEWEB)

1987-03-01

This report presents the preliminary findings from the first phase of the Environmental Survey of the United States Department of Energy (DOE) Mound Plant, conducted August 18 through 29, 1986. The objective of the Survey is to identify environmental problems and areas of environmental risk associated with the Mound Plant. The Survey covers all environmental media and all areas of environmental regulation. It is being performed in accordance with the DOE Environmental Survey Manual. The on-site phase of the Survey involves the review of existing site environmental data, observations of the operations carried on at the Mound Plant, and interviews with site personnel. The Survey found no environmental problems at the Mound Plant that represent an immediate threat to human life. The environmental problems identified at the Mound Plant by the Survey confirm that the site is confronted with a number of environmental problems which are by and large a legacy from past practices at a time when environmental problems were less well understood. Theses problems vary in terms of their magnitude and risk, as described in this report. Although the sampling and analysis performed by the Mound Plant Survey will assist in further identifying environmental problems at the site, a complete understanding of the significance of some of the environmental problems identified requires a level of study and characterization that is beyond the scope of the Survey. Actions currently under way or planned at the site, particularly the Phase II activities of the Comprehensive Environmental Analysis and Response Program (CEARP) as developed and implemented by the Albuquerque Operations Office, will contribute toward meeting this requirement. 85 refs., 24 figs., 20 tabs.

Nutrient dynamics and plant assemblages of Macrotermes falciger mounds in a savanna ecosystem

Science.gov (United States)

Muvengwi, Justice; Ndagurwa, Hilton G. T.; Nyenda, Tatenda; Mbiba, Monicah

2016-10-01

Termites through mound construction and foraging activities contribute significantly to carbon and nutrient fluxes in nutrient-poor savannas. Despite this recognition, studies on the influence of termite mounds on carbon and nitrogen dynamics in sub-tropical savannas are limited. In this regard, we examined soil nutrient concentrations, organic carbon and nitrogen mineralization in incubation experiments in mounds of Macrotermes falciger and surrounding soils of sub-tropical savanna, northeast Zimbabwe. We also addressed whether termite mounds altered the plant community and if effects were similar across functional groups i.e. grasses, forbs or woody plants. Mound soils had significantly higher silt and clay content, pH and concentrations of calcium (Ca), magnesium (Mg), potassium (K), organic carbon (C), ammonium (NH4+) and nitrate (NO3-) than surrounding soils, with marginal differences in phosphorus (P) and sodium (Na) between mounds and matrix soils. Nutrient enrichment increased by a factor ranging from 1.5 for C, 4.9 for Mg up to 10.3 for Ca. Although C mineralization, nitrification and nitrification fraction were similar between mounds and matrix soils, nitrogen mineralization was elevated on mounds relative to surrounding matrix soils. As a result, termite mounds supported unique plant communities rich and abundant in woody species but less diverse in grasses and forbs than the surrounding savanna matrix in response to mound-induced shifts in soil parameters specifically increased clay content, drainage and water availability, nutrient status and base cation (mainly Ca, Mg and Na) concentration. In conclusion, by altering soil properties such as texture, moisture content and nutrient status, termite mounds can alter the structure and composition of sub-tropical savanna plant communities, and these results are consistent with findings in other savanna systems suggesting that increase in soil clay content, nutrient status and associated changes in the plant

Solar-powered ventilation of African termite mounds.

Science.gov (United States)

Ocko, Samuel A; King, Hunter; Andreen, David; Bardunias, Paul; Turner, J Scott; Soar, Rupert; Mahadevan, L

2017-09-15

How termite mounds function to facilitate climate control is still only partially understood. Recent experimental evidence in the mounds of a single species, the south Asian termite Odontotermes obesus , suggests that the daily oscillations of radiant heating associated with diurnal insolation patterns drive convective flow within them. How general this mechanism is remains unknown. To probe this, we consider the mounds of the African termite Macrotermes michaelseni , which thrives in a very different environment. By directly measuring air velocities and temperatures within the mound, we see that the overall mechanisms and patterns involved are similar to that in the south Asian species. However, there are also some notable differences between the physiology of these mounds associated with the temporal variations in radiant heating patterns and CO 2 dynamics. Because of the difference between direct radiant heating driven by the position of the sun in African conditions, and the more shaded south Asian environments, we see changes in the convective flows in the two types of mounds. Furthermore, we also see that the south Asian mounds show a significant overturning of stratified gases, once a day, while the African mounds have a relatively uniform concentration of CO 2 Overall, our observations show that despite these differences, termite architectures can harness periodic solar heating to drive ventilation inside them in very different environments, functioning as an external lung, with clear implications for human engineering. © 2017. Published by The Company of Biologists Ltd.

Rubble Mound Breakwater Failure Modes

DEFF Research Database (Denmark)

Burcharth, H. F.; Z., Liu

1995-01-01

The RMBFM-Project (Rubble Mound Breakwater Failure Modes) is sponsored by the Directorate General XII of the Commission of the European Communities under the Contract MAS-CT92- 0042, with the objective of contributing to the development of rational methods for the design of rubble mound breakwate...

Analysis of Rubble Mound Breakwaters

DEFF Research Database (Denmark)

Mettam, J.D.; Allsop, N.W.H.; Bonafous, P.

Working Group 12 was set up to consider the analysis of rubble mound breakwaters with a view to achieving a better understanding of safety aspects. The working group decided to develop the practical application of risk analysis in the design of rubble mound breakwaters by using partial coefficien...

Bacterial density and community structure associated with aggregate size fractions of soil-feeding termite mounds.

Science.gov (United States)

Fall, S; Nazaret, S; Chotte, J L; Brauman, A

2004-08-01

The building and foraging activities of termites are known to modify soil characteristics such as the heterogeneity. In tropical savannas the impact of the activity of soil-feeding termites ( Cubitermes niokoloensis) has been shown to affect the properties of the soil at the aggregate level by creating new soil microenvironments (aggregate size fractions) [13]. These changes were investigated in greater depth by looking at the microbial density (AODC) and the genetic structure (automated rRNA intergenic spacer analysis: ARISA) of the communities in the different aggregate size fractions (i.e., coarse sand, fine sand, coarse silt, fine silt, and dispersible clays) separated from compartments (internal and external wall) of three Cubitermes niokoloensis mounds. The bacterial density of the mounds was significantly higher (1.5 to 3 times) than that of the surrounding soil. Within the aggregate size fractions, the termite building activity resulted in a significant increase in bacterial density within the coarser fractions (>20 mum). Multivariate analysis of the ARISA profiles revealed that the bacterial genetic structures of unfractionated soil and soil aggregate size fractions of the three mounds was noticeably different from the savanna soil used as a reference. Moreover, the microbial community associated with the different microenvironments in the three termite mounds revealed three distinct clusters formed by the aggregate size fractions of each mound. Except for the 2-20 mum fraction, these results suggest that the mound microbial genetic structure is more dependent upon microbial pool affiliation (the termite mound) than on the soil location (aggregate size fraction). The causes of the specificity of the microbial community structure of termite mound aggregate size fractions are discussed.

How Termite Mounds Breath?

Science.gov (United States)

Saxena, Saurabh; Yaghoobian, Neda

2017-11-01

Fungus-cultivating termites of the subfamily Macrotermitinae that are extensively found throughout sub-Saharan Africa and south East Asia are one species of termites that collectively build massive, uninhabited, complex structures. These structures, which are much larger than the size of an individual termite, effectively use natural wind and solar energies and the energy embodied in colony's metabolic activity to maintain the necessary condition for termite survival. These mounds enclose a subterranean nest, where the termite live and cultivate fungus, as well as a complex network of tunnels consisting of a large, vertically oriented central chimney, surface conduits, and lateral connectives that connect the chimney and the surface conduits. In this study, we use computational modeling to explore the combined interaction of geometry, heterogeneous thermal mass, and porosity with the external turbulent wind and solar radiation to investigate the physical principles and fundamental aero-thermodynamics underlying the controlled and stable climate of termite mounds. Exploitation of natural resources of wind and solar energies in these natural systems for the purpose of ventilation will lead to new lessons for improving human habitats conditions.

Layered hydrothermal barite-sulfide mound field, East Diamante Caldera, Mariana volcanic arc

Science.gov (United States)

Hein, James R.; de Ronde, Cornel E. J.; Koski, Randolph A.; Ditchburn, Robert G.; Mizell, Kira; Tamura, Yoshihiko; Stern, Robert J.; Conrad, Tracey; Ishizuka, Osamu; Leybourne, Matthew I.

2014-01-01

East Diamante is a submarine volcano in the southern Mariana arc that is host to a complex caldera ~5 × 10 km (elongated ENE-WSW) that is breached along its northern and southwestern sectors. A large field of barite-sulfide mounds was discovered in June 2009 and revisited in July 2010 with the R/V Natsushima, using the ROV Hyper-Dolphin. The mound field occurs on the northeast flank of a cluster of resurgent dacite domes in the central caldera, near an active black smoker vent field. A 40Ar/39Ar age of 20,000 ± 4000 years was obtained from a dacite sample. The mound field is aligned along a series of fractures and extends for more than 180 m east-west and >120 m north-south. Individual mounds are typically 1 to 3 m tall and 0.5 to 2 m wide, with lengths from about 3 to 8 m. The mounds are dominated by barite + sphalerite layers with the margins of each layer composed of barite with disseminated sulfides. Rare, inactive spires and chimneys sit atop some mounds and also occur as clusters away from the mounds. Iron and Mn oxides are currently forming small (caldera, mineralization resulted from focused flow along small segments of linear fractures rather than from a point source, typical of hydrothermal chimney fields. Based on the mineral assemblage, the maximum fluid temperatures were ~260°C, near the boiling point for the water depths of the mound field (367–406 m). Lateral fluid flow within the mounds precipitated interstitial sphalerite, silica, and Pb minerals within a network of barite with disseminated sulfides; silica was the final phase to precipitate. The current low-temperature precipitation of Fe and Mn oxides and silica may represent rejuvenation of the system.

Formation and Control of Self-Sealing High Permeability Groundwater Mounds in Impermeable Sediment: Implications for SUDS and Sustainable Pressure Mound Management

Directory of Open Access Journals (Sweden)

David D. J. Antia

2009-10-01

Full Text Available A groundwater mound (or pressure mound is defined as a volume of fluid dominated by viscous flow contained within a sediment volume where the dominant fluid flow is by Knudsen Diffusion. High permeability self-sealing groundwater mounds can be created as part of a sustainable urban drainage scheme (SUDS using infiltration devices. This study considers how they form, and models their expansion and growth as a function of infiltration device recharge. The mounds grow through lateral macropore propagation within a Dupuit envelope. Excess pressure relief is through propagating vertical surge shafts. These surge shafts can, when they intersect the ground surface result, in high volume overland flow. The study considers that the creation of self-sealing groundwater mounds in matrix supported (clayey sediments (intrinsic permeability = 10–8 to 10–30 m3 m–2 s–1 Pa–1 is a low cost, sustainable method which can be used to dispose of large volumes of storm runoff (<20→2,000 m3/24 hr storm/infiltration device and raise groundwater levels. However, the inappropriate location of pressure mounds can result in repeated seepage and ephemeral spring formation associated with substantial volumes of uncontrolled overland flow. The flow rate and flood volume associated with each overland flow event may be substantially larger than the associated recharge to the pressure mound. In some instances, the volume discharged as overland flow in a few hours may exceed the total storm water recharge to the groundwater mound over the previous three weeks. Macropore modeling is used within the context of a pressure mound poro-elastic fluid expulsion model in order to analyze this phenomena and determine (i how this phenomena can be used to extract large volumes of stored filtered storm water (at high flow rates from within a self-sealing high permeability pressure mound and (ii how self-sealing pressure mounds (created using storm water infiltration can be used to

Mound technology for isolation of decommissioned NPPs

International Nuclear Information System (INIS)

Korovkin, S.V.; Tutunina, E.V.

2012-01-01

The problem of NPPs' decommissioning calls for immediate attention. Today the most socially acceptable solution is green lawn, but due to the difficulty of this option, alternative solutions are being developed as well. The authors believe that the option is isolation of shut-down NPPs in-situ by covering them with layers of inert materials, resulting in the formation of a mound. In this case the reactor building itself becomes a repository that holds solid radioactive wastes generated over the time of unit operation. Spent fuel is to be shipped out of the site. A layer of inert materials several meters thick guarantees secure protection against ionising radiation and unauthorised access to the structures in isolation. The structures inside the mound are also inaccessible to ground waters. The green mound concept is considered as well as the mound backfilling technology which excludes collapse under the weight of inert materials that form the mound. It is pointed out that never-completed Voronezh nuclear heating plant is the optimal object for field-testing of the suggested technology [ru

Plutonium, americium, and uranium in blow-sand mounds of safety-shot sites at the Nevada Test Site and the Tonopah Test Range

International Nuclear Information System (INIS)

Essington, E.H.; Gilbert, R.O.; Wireman, D.L.; Brady, D.N.; Fowler, E.B.

1977-01-01

Blow-sand mounds or miniature sand dunes and mounds created by burrowing activities of animals were investigated by the Nevada Applied Ecology Group (NAEG) to determine the influence of mounds on plutonium, americium, and uranium distributions and inventories in areas of the Nevada Test Site and Tonopah Test Range. Those radioactive elements were added to the environment as a result of safety experiments of nuclear devices. Two studies were conducted. The first was to estimate the vertical distribution of americium in the blow-sand mounds and in the desert pavement surrounding the mounds. The second was to estimate the amount or concentration of the radioactive materials accumulated in the mound relative to the desert pavement. Five mound types were identified in which plutonium, americium, and uranium concentrations were measured: grass, shrub, complex, animal, and diffuse. The mount top (that portion above the surrounding land surface datum), the mound bottom (that portion below the mound to a depth of 5 cm below the surrounding land surface datum), and soil from the immediate area surrounding the mound were compared separately to determine if the radioactive elements had concentrated in the mounds. Results of the studies indicate that the mounds exhibit higher concentrations of plutonium, americium, and uranium than the immediate surrounding soil. The type of mound does not appear to have influenced the amount of the radioactive material found in the mound except for the animal mounds where the burrowing activities appear to have obliterated distribution patterns

SPATIAL VARIABILITY AND VITALITY OF EPIGEOUS TERMITE MOUNDS IN PASTURES OF MATO GROSSO DO SUL, BRAZIL

Directory of Open Access Journals (Sweden)

Sandra Santana Lima

2015-02-01

Full Text Available Epigeous termite mounds are frequently observed in pasture areas, but the processes regulating their population dynamics are poorly known. This study evaluated epigeous termite mounds in cultivated grasslands used as pastures, assessing their spatial distribution by means of geostatistics and evaluating their vitality. The study was conducted in the Cerrado biome in the municipality of Rio Brilhante, Mato Grosso do Sul, Brazil. In two pasture areas (Pasture 1 and Pasture 2, epigeous mounds (nests were georeferenced and analyzed for height, circumference and vitality (inhabited or not. The area occupied by the mounds was calculated and termite specimens were collected for taxonomic identification. The spatial distribution pattern of the mounds was analyzed with geostatistical procedures. In both pasture areas, all epigeous mounds were built by the same species, Cornitermes cumulans. The mean number of mounds per hectare was 68 in Pasture 1 and 127 in Pasture 2, representing 0.4 and 1 % of the entire area, respectively. A large majority of the mounds were active (vitality, 91 % in Pasture 1 and 84 % in Pasture 2. A “pure nugget effect” was observed in the semivariograms of height and nest circumference in both pastures reflecting randomized spatial distribution and confirming that the distribution of termite mounds in pastures had a non-standard distribution.

Diurnal respiration of a termite mound

Science.gov (United States)

King, Hunter; Ocko, Samuel; Mahadevan, L.

2014-11-01

Many species of fungus-harvesting termites build largely empty, massive mound structures which protrude from the ground above their subterranean nests. It has been long proposed that the function of these mounds is to facilitate exchange of heat, humidity, and respiratory gases; this would give the colony a controlled climate in which to raise fungus and brood. However, the specific mechanism by which the mound achieves ventilation has remained a topic of debate, as direct measurement of internal air flows has remained difficult. By directly measuring these elusive, tiny flows with a custom sensor, we find that the mound architecture of the species Odontotermes obesus takes advantage of daily oscillations in ambient temperature to drive convection and gas transport. This contradicts previous theories, which point to internal metabolic heating and external wind as driving forces. Our result, a novel example of deriving useful work from a fluctuating scalar parameter, should contribute to better understanding insect swarm construction and possible development in passive human architecture, both of which have been spurred by previous research on termites. We acknowledge support from HFSP.

Shallow water mud-mounds of the Early Devonian Buchan Group, East Gippsland, Australia

Science.gov (United States)

Tosolini, A.-M. P.; Wallace, M. W.; Gallagher, S. J.

2012-12-01

The Lower Devonian Rocky Camp Member of the Murrindal Limestone, Buchan Group of southeastern Australia consists of a series of carbonate mud-mounds and smaller lagoonal bioherms. The Rocky Camp mound is the best exposed of the mud-mounds and has many characteristics in common with Waulsortian (Carboniferous) mounds. Detailed paleoecological and sedimentological studies indicate that the mound initially accumulated in the photic zone, in contrast to most of the previously recorded mud-mounds. Five facies are present in the mud-mound: a Dasycladacean Wackestone Facies at the base of the mound represents a moderate energy, shallow water bank environment within the photic zone. A Crinioidal Wackestone Facies was deposited in a laterally equivalent foreslope setting. A Poriferan-Crinoidal Mudstone Facies developed in a quiet, deeper water, lee-side mound setting associated with a minor relative sea-level rise. A Stromatoporoid-Coralline Packstone Facies in the upper part of the mound deposited in a high-energy, fair-weather wave base, mound-front environment. The crest of the mound is represented by a Crinoidal-Receptaculitid Packstone Facies indicative of a moderate-energy mound-top environment in the photic zone, sheltered by the mound-front stromatoporoid-coral communities. A mound flank facies is present on the southern side of the mound and this consists of high-energy crinoidal grainstones. Mud-mound deposition was terminated by a transgression that deposited dark gray, fossil-poor marl of the overlying Taravale Formation. The Rocky Camp mound appears to have originated in shallow water photic zone conditions and grew into a high-energy environment, with the mound being eventually colonized by corals and stromatoporoids. The indications of a high-energy environment during later mound growth (growth form of colonial metazoans and grainstones of the flanking facies) suggest that the micrite in the mound was autochthonous and implies the presence of an energy

Temporal variability in shell mound formation at Albatross Bay, northern Australia.

Directory of Open Access Journals (Sweden)

Simon J Holdaway

Full Text Available We report the results of 212 radiocarbon determinations from the archaeological excavation of 70 shell mound deposits in the Wathayn region of Albatross Bay, Australia. This is an intensive study of a closely co-located group of mounds within a geographically restricted area in a wider region where many more shell mounds have been reported. Valves from the bivalve Tegillarca granosa (Linnaeus, 1758 were dated. The dates obtained are used to calculate rates of accumulation for the shell mound deposits. These demonstrate highly variable rates of accumulation both within and between mounds. We assess these results in relation to likely mechanisms of shell deposition and show that rates of deposition are affected by time-dependent processes both during the accumulation of shell deposits and during their subsequent deformation. This complicates the interpretation of the rates at which shell mound deposits appear to have accumulated. At Wathayn, there is little temporal or spatial consistency in the rates at which mounds accumulated. Comparisons between the Wathayn results and those obtained from shell deposits elsewhere, both in the wider Albatross Bay region and worldwide, suggest the need for caution when deriving behavioural inferences from shell mound deposition rates, and the need for more comprehensive sampling of individual mounds and groups of mounds.

Termite mounds harness diurnal temperature oscillations for ventilation.

Science.gov (United States)

King, Hunter; Ocko, Samuel; Mahadevan, L

2015-09-15

Many species of millimetric fungus-harvesting termites collectively build uninhabited, massive mound structures enclosing a network of broad tunnels that protrude from the ground meters above their subterranean nests. It is widely accepted that the purpose of these mounds is to give the colony a controlled microclimate in which to raise fungus and brood by managing heat, humidity, and respiratory gas exchange. Although different hypotheses such as steady and fluctuating external wind and internal metabolic heating have been proposed for ventilating the mound, the absence of direct in situ measurement of internal air flows has precluded a definitive mechanism for this critical physiological function. By measuring diurnal variations in flow through the surface conduits of the mounds of the species Odontotermes obesus, we show that a simple combination of geometry, heterogeneous thermal mass, and porosity allows the mounds to use diurnal ambient temperature oscillations for ventilation. In particular, the thin outer flutelike conduits heat up rapidly during the day relative to the deeper chimneys, pushing air up the flutes and down the chimney in a closed convection cell, with the converse situation at night. These cyclic flows in the mound flush out CO2 from the nest and ventilate the colony, in an unusual example of deriving useful work from thermal oscillations.

A Preliminary Study on Elimination of Colonies of the Mound Building Termite Macrotermes gilvus (Hagen Using a Chlorfluazuron Termite Bait in the Philippines

Directory of Open Access Journals (Sweden)

Partho Dhang

2011-11-01

Full Text Available The effectiveness of a chlorfluazuron termite bait in eliminating colonies of the termite species Macrotermes gilvus (Hagen was evaluated under field conditions. Three active termite mounds were chosen for this study, two acted as test mounds and the other as the control. Four In-Ground Stations (IGS were installed around each mound. Interception occurred almost immediately in all the stations, which were subsequently baited. The control mound was fed a bait matrix lacking the active ingredient. Stations were re-baited every 2 weeks for 10–12 weeks until bait consumption ceased in the test mounds. The mounds were left undisturbed for four more weeks before being destructively sampled. The desiccated remains of workers, soldiers, late instars and queen were found upon sampling the treated mounds. A few live termites were located in one treated mound but were darkly pigmented indicating bait consumption. The control mound remained healthy and did not show any visible sign of negative impact. The bait successfully suppressed or eliminated both M. gilvus colonies within 16 weeks from commencement of feeding.

Geophysical Survey of Poverty Point UNESCO World Heritage Site Mound A

Science.gov (United States)

Frazer, W.; Bourke, J. R.; De Smet, T.; Nikulin, A.

2017-12-01

Poverty Point is an UNESCO World Heritage Site located in northern Louisiana, known for its six earthwork ridges and mounds of archeological significance. The largest of these earthworks and most significant feature on the site, Mound A is over 70 feet (21 m) high and 640 feet (200 m) long. To construct this mound, it would have taken about 16 million basket loads of dirt which weight approximately 50 lbs. each (23 kg). The current archeological theory describing the construction of Mound A states it was built in three months at most, with some suggesting construction times as short as a month, but beyond this not much else is known about Mound A or Poverty Point. The pace of Mound A's construction has been used as evidence to support the idea that there was a central leader directing its construction and that the population inhabiting the site was more socio-politically complex than previous hunter-gatherer populations in North America. Evidence of heterogeneity and stratigraphic layering, however, is an indication of a slow mound construction over centuries by a relatively egalitarian hunter-gather society. A greater understanding of the construction style and timeline for the construction of Mound A will lead to a greater understanding to the site, its people their lifestyles. Mound Builders have been known to cap mounds they have built if they were to be built in stages so if Mound A was built in stages it is likely capped with some more dense material than the dirt surrounding it. To better understand the construction history of Mound A we collected photogrammetry, seismic reflection, ground-penetrating radar, frequency-domain electromagnetic-induction, resistivity, and magnetometry data over the mound. The seismic data had a normal moveout correction, it was stacked and migrated. Additionally, with the application of quadcopter-based photogrammetry a three-dimensional digital model of Mound A was developed to display and assist in further understanding and

Iron microbial communities in Belgian Frasnian carbonate mounds

OpenAIRE

Boulvain, F.; De Ridder, C.; Mamet, B.; Preat, A.; Gillan, D.

2001-01-01

The Belgian Frasnian carbonate mounds occur in three stratigraphic levels in an overall backstepping succession. Petit-Mont and Arche Members form the famous red and grey “marble” exploited for ornamental stone since Roman times. The evolution and distribution of the facies in the mounds is thought to be associated with ecologic evolution and relative sea-level fluctuations. Iron oxides exist in five forms in the Frasnian mounds; four are undoubtedly endobiotic organized structures: (1) micro...

A Preliminary Study on Elimination of Colonies of the Mound Building Termite Macrotermes gilvus (Hagen) Using a Chlorfluazuron Termite Bait in the Philippines

OpenAIRE

Partho Dhang

2011-01-01

The effectiveness of a chlorfluazuron termite bait in eliminating colonies of the termite species Macrotermes gilvus (Hagen) was evaluated under field conditions. Three active termite mounds were chosen for this study, two acted as test mounds and the other as the control. Four In-Ground Stations (IGS) were installed around each mound. Interception occurred almost immediately in all the stations, which were subsequently baited. The control mound was fed a bait matrix lacking the active ingred...

Application of 5700.6B, quality assurance, to ES and H programs: Mound's approach and results

International Nuclear Information System (INIS)

Edling, D.A.

1985-01-01

Quality Assurance has always been integral to Mound's production and support operations. Weapons material and other designated material for WR programs are processed and controlled per the requirements of DOE/AL Quality Control Policy QC-1. Mound's non-WR activities, such as siting, design, construction, testing, operation, maintenance, development and production of materials, components, and systems, and acquisition of research and technology data are to be processed and controlled per the requirements of AL Order 5700.6. This paper presents an overview of the entire Quality Assurance Program at Mound and specifically addresses Mound's formal application of Quality Assurance to our comprehensive Environmental, Safety and Health (ES and H) Programs. 4 figures, 1 table

Are termite mounds biofilters for methane? - Challenges and new approaches to quantify methane oxidation in termite mounds

Science.gov (United States)

Nauer, Philipp A.; Hutley, Lindsay B.; Bristow, Mila; Arndt, Stefan K.

2015-04-01

Methane emissions from termites contribute around 3% to global methane in the atmosphere, although the total source estimate for termites is the most uncertain among all sources. In tropical regions, the relative source contribution of termites can be far higher due to the high biomass and relative importance of termites in plant decomposition. Past research focused on net emission measurements and their variability, but little is known about underlying processes governing these emissions. In particular, microbial oxidation of methane (MOX) within termite mounds has rarely been investigated. In well-studied ecosystems featuring an oxic matrix above an anoxic methane-producing habitat (e.g. landfills or sediments), the fraction of oxidized methane (fox) can reach up to 90% of gross production. However, conventional mass-balance approaches to apportion production and consumption processes can be challenging to apply in the complex-structured and almost inaccessible environment of a termite mound. In effect, all field-based data on termite-mound MOX is based on one study that measured isotopic shifts in produced and emitted methane. In this study a closed-system isotope fractionation model was applied and estimated fox ranged from 10% to almost 100%. However, it is shown here that by applying an open-system isotope-pool model, the measured isotopic shifts can also be explained by physical transport of methane alone. Different field-based methods to quantify MOX in termite mounds are proposed which do not rely on assumptions of physical gas transport. A simple approach is the use of specific inhibitors for MOX, e.g. difluoromethane (CH2F2), combined with chamber-based flux measurements before and after their application. Data is presented on the suitability of different inhibitors and first results of their application in the field. Alternatively, gas-tracer methods allow the quantification of methane oxidation and reaction kinetics without knowledge of physical gas

Facies architecture and diagenesis of Belgian Late Frasnian carbonate mounds

OpenAIRE

Boulvain, Frédéric

2001-01-01

Late Frasnian Petit-Mont Member carbonate mounds occur in the southern pail of the Dinant Synclinorium and in the Philippeville Anticline (SW Belgium). These mounds are 30 to 80 m thick and 100 to 250 m in diameter. They are embedded in shale, nodular shale and argillaceous limestone. Based on facies mapping of 14 buildups and related off-mound sediments, these mounds typically started from below the photic and storm wave base zones and builtup into shallow water environments. Above an argill...

Simulation of Groundwater Mounding Beneath Hypothetical Stormwater Infiltration Basins

Science.gov (United States)

Carleton, Glen B.

2010-01-01

Groundwater mounding occurs beneath stormwater management structures designed to infiltrate stormwater runoff. Concentrating recharge in a small area can cause groundwater mounding that affects the basements of nearby homes and other structures. Methods for quantitatively predicting the height and extent of groundwater mounding beneath and near stormwater Finite-difference groundwater-flow simulations of infiltration from hypothetical stormwater infiltration structures (which are typically constructed as basins or dry wells) were done for 10-acre and 1-acre developments. Aquifer and stormwater-runoff characteristics in the model were changed to determine which factors are most likely to have the greatest effect on simulating the maximum height and maximum extent of groundwater mounding. Aquifer characteristics that were changed include soil permeability, aquifer thickness, and specific yield. Stormwater-runoff variables that were changed include magnitude of design storm, percentage of impervious area, infiltration-structure depth (maximum depth of standing water), and infiltration-basin shape. Values used for all variables are representative of typical physical conditions and stormwater management designs in New Jersey but do not include all possible values. Results are considered to be a representative, but not all-inclusive, subset of likely results. Maximum heights of simulated groundwater mounds beneath stormwater infiltration structures are the most sensitive to (show the greatest change with changes to) soil permeability. The maximum height of the groundwater mound is higher when values of soil permeability, aquifer thickness, or specific yield are decreased or when basin depth is increased or the basin shape is square (and values of other variables are held constant). Changing soil permeability, aquifer thickness, specific yield, infiltration-structure depth, or infiltration-structure shape does not change the volume of water infiltrated, it changes the

Conductive heat flow at the TAG Active Hydrothermal Mound: Results from 1993-1995 submersible surveys

Science.gov (United States)

Becker, K.; Von Herzen, R.; Kirklin, J.; Evans, R.; Kadko, D.; Kinoshita, M.; Matsubayashi, O.; Mills, R.; Schultz, A.; Rona, P.

We report 70 measurements of conductive heat flow at the 50-m-high, 200-m-diameter TAG active hydrothermal mound, made during submersible surveys with Alvin in 1993 and 1995 and Shinkai 6500 in 1994. The stations were all measured with 5-thermistor, 0.6- or 1-m-long Alvin heat flow probes, which are capable of determining both gradient and thermal conductivity, and were transponder-navigated to an estimated accuracy of ±5-10 m relative to the 10-m-diameter central complex of black smokers. Within 20 m of this complex, conductive heat flow values are extremely variable (0.1- > 100 W/m²), which can only be due to local spatial and possible temporal variability in the immediate vicinity of the vigorous discharge sites. A similar local variability is suggested in the “Kremlin” area of white smokers to the southeast of the black smoker complex. On the south and southeast side of the mound, there is very high heat flow (3.7- > 25 W/m²) on the sedimented terraces that slope down from the Kremlin area. Heat flow is also high (0.3-3 W/m²) in the pelagic carbonate sediments on the surrounding seafloor within a few tens of meters of the southwest, northwest, and northeast sides of the mound. On the west side of the sulfide rubble plateau that surrounds the central black smoker peak, there is a coherent belt of very low heat flow (smokers, suggestive of local, shallow recharge of bottom water. The three submersible surveys spanned nearly two years, but showed no indication of any temporal variability in conductive heat flow over this time scale, whether natural or induced by ODP drilling in 1994.

Radiological surveillance of members of the public during earthmoving activities in the area of the Ciemat mound

International Nuclear Information System (INIS)

Alvarez, A.; Yague, L.; Navarro, N.; Gasco, C.; Ortiz, M. T.; Quinones, J.

2013-01-01

In the year 2012 was undertaken excavation and earthwork of the mound. The lands of this area contained remains sterile uranium mining and therefore concentrations of natural radionuclides higher than natural radioactive background activity. In order to assess the radiological impact on the public, was a theoretical evaluation of the dose inhaled that would get a person who remained in the vicinity during the making of the work. (Author)

Prey and mound disassembly, manipulation and transport by fire ant collectives

Science.gov (United States)

Dutta, Bahnisikha; Monaenkova, Daria; Goodisman, Michael A.; Goldman, Daniel

Fire ants inhabit subterranean nests covered by a hemispherical mound of soil permeated by narrow ( 1 body length diameter) tunnels. Fire ants can use their mound for long-term food storage [Gayahan &Tschinkel, J. Insect Sci.,2008]. Since mound tunnels are narrow, we expect that in addition to prey manipulation, mound reconfiguration could also be an important aspect of the food storage strategy. Ant colonies collected from wild were allowed to build nests in containers filled with clay soil in the laboratory. These colonies were offered diverse prey embedded with lead markers, including mealworms, crickets and shrimp. Ant-prey-soil interactions on the nest surface were recorded using overhead video and subsurface using x-ray imaging. Individual ants involved in prey storage exhibited three distinct behaviors: prey maneuvering, prey dissection and mound reconfiguration. Small prey (e.g. mealworms) were collectively carried intact into the mound through a tunnel, and then disassembled within the mound. Larger prey (e.g. shrimp) were dismantled into small pieces above the surface and carried to mound tunnels. The bodies of hard medium-sized prey (e.g. crickets) were buried after limb removal and then disassembled and moved into tunnels. Soil reconfiguration occurred in all cases.

Sulphur Extraction at Bryan Mound

Energy Technology Data Exchange (ETDEWEB)

Kirby, Carolyn L [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Lord, Anna C. Snider [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-08-01

The Bryan Mound caprock was subjected to extens ive sulphur mining prior to the development of the Strategic Petroleum Reserve. Undoubtedl y, the mining has modified the caprock integrity. Cavern wells at Bryan Mound have been subject to a host of well integr ity concerns with many likely compromised by the cavernous capro ck, surrounding corrosive environment (H ₂ SO ₄ ), and associated elevated residual temperatures al l of which are a product of the mining activities. The intent of this study was to understand the sulphur mining process and how the mining has affected the stability of the caprock and how the compromised caprock has influenced the integrity of the cavern wells. After an extensiv e search to collect pert inent information through state agencies, literature sear ches, and the Sandia SPR librar y, a better understanding of the caprock can be inferred from the knowledge gaine d. Specifically, the discovery of the original ore reserve map goes a long way towards modeling caprock stability. In addition the gained knowledge of sulphur mining - subs idence, superheated corrosive wa ters, and caprock collapse - helps to better predict the post mi ning effects on wellbore integrity. This page intentionally left blank

Influence of soil pedological properties on termite mound stability

OpenAIRE

Jouquet, Pascal; Guilleux, N.; Caner, L.; Chintakunta, S.; Ameline, M.; Shanbhag, R. R.

2016-01-01

This study investigated the influence of soil properties on the density and shape of epigeous fungus-growing termite nests in a dry deciduous forest in Karnataka, India. In this environment, Odontotermes obesus produces cathedral shaped mounds. Their density, shape (height and volume) and soil physicochemical properties were analyzed in ferralsol and vertisol environments. No significant difference was observed in O. obesus mound density (n = 2.7 mound ha(-1) on average in the vertisol and fe...

Formation of Burial Mounds of the Sarmatian Time in the Basin of the Esaulovsky Aksai River

Directory of Open Access Journals (Sweden)

Elena A. Korobkova

2017-09-01

Full Text Available The article deals with the features of the formation of the burial mounds in the basin of the Esaulovsky Aksai river in the Sarmatian period. Most of the burial mounds of the region begin to form in the Bronze Age and continue to function throughout the early, middle and early late-Sarmatian periods. Most of the burial mounds were located on the watersheds and above-flood terraces of different levels. All of them are characterized by same principles of planning, barrows in them are stretched in a chain in the natural form of the terrace on which the burial mound was built. The territories developed already in the Bronze Age were chosen for creating mounds in the early Sarmatian period. The main part of them is concentrated on a small section landplot of the middle course of the Esaulovsky Aksai river. During the Middle Sarmatian period, the main part of barrows were also located in the middle course of the Esaulovsky Aksai, but represented 2 plots. One of these plots continues to use large burial mounds of the previous period, and the other one undergoes the creation of small barrow groups consisting usually of two-three barrows containing the richest burials of the region with the “classical” set of Middle Sarmatian features. In the late Sarmatian period, as well as in the previous stages of the Sarmatian culture, the burial mounds of the middle course of the Esaulovsky Aksai continue to be used, which cease to function no later than at the first half of the 3rd century AD. But the territory of actively used burial mounds changes, and the main complexes of that time concentrate in the upper reaches, where new burial mounds are created and continue to function until the end of the Sarmatian era.

Mound Laboratory tritium environmental study: 1976--1977

International Nuclear Information System (INIS)

Kershner, C.J.; Rhinehammer, T.B.

1978-01-01

In the course of an extensive investigation of tritium in the aquifer underlying the Mound Facility site, an unusual behavior was noted for a beta-emitting radionuclide contaminant present in the environs of the abandoned Miami-Erie Canal adjacent to the laboratory site. The soil contaminant was determined to be tritium, of which 90% was in the form of a relatively stable or bound species that was not readily exchangeable with the free water in the soil. (Bound-to-exchangeable transfer half-time was found to be approximately 3 yr.) The contamination was found to be concentrated within two feet of the surface in the center of the canal channel and near the Facility site drainage ditch and canal confluence. In order to characterize the contaminant and to assess its potential for reaching the aquifer, an analysis program and study were initiated in September 1976. The results and findings from the first phase of this work which was completed in February 1977 are the subject of this report

The Porcupine Bank Canyon coral mounds: oceanographic and topographic steering of deep-water carbonate mound development and associated phosphatic deposition

Science.gov (United States)

Mazzini, A.; Akhmetzhanov, A.; Monteys, X.; Ivanov, M.

2012-06-01

The head of a canyon system extending along the western Porcupine Bank (west of Ireland) and which accommodates a large field of giant carbonate mounds was investigated during two cruises (INSS 2000 and TTR-13). Multibeam and sidescan sonar data (600-1,150 m water depth) suggest that the pre-existing seabed topography acts as a significant factor controlling mound distribution and shape. The mounds are concentrated along the edges of the canyon or are associated with a complex fault system traced around the canyon head, comprising escarpments up to 60 m high and several km long. The sampling for geochemical and petrographic analysis of numerous types of authigenic deposits was guided by sidescan sonar and video recordings. Calcite-cemented biogenic rubble was observed at the top and on the flanks of the carbonate mounds, being associated with both living and dead corals ( Lophelia pertusa, Madrepora oculata and occasional Desmophyllum cristagalli). This can plausibly be explained by dissolution of coral debris facilitated by strong currents along the mound tops and flanks. In turn, the dissolved carbon is recycled and precipitated as interstitial micrite. Calcite, dolomite and phosphatic hardgrounds were identified in samples from the escarpment framing the eastern part of the survey area. The laterally extensive phosphatic hardgrounds represent a novel discovery in the region, supplying hard substrata for the establishment of new coral colonies. Based on existing knowledge of regional oceanographic conditions, complemented with new CTD measurements, it is suggested that water column stratification, enhanced bottom currents, and upwelling facilitate the deposition of organic matter, followed by phosphatisation leading to the formation of phosphate-glauconite deposits. The occurrence of strong bottom currents was confirmed by means of video observations combined with acoustic and sampling data, providing circumstantial evidence of fine- to medium-grained sand

Rainfall and soil properties influence termite mound abundance and height: A case study with Odontotermes obesus (Macrotermitinae) mounds in the Indian Western Ghats forests

OpenAIRE

Kabbaj, Meyssoun; Sundararaj, Ramachandran; Jouquet, Pascal

2017-01-01

Several fungus-growing termite species build mounds, or termitaria, that are conspicuous features of African and Asian landscapes. Studies of the genus Macrotermes in Africa have established that their mounds provide an environment buffered against extremes of temperature and humidity, as well as protection from predators, and are correspondingly modified in composition. However, no studies are available in the specific context of the Asian continent where termite mounds are also abundant. He...

Rainfall and soil properties influence termite mound abundance and height : a case study with Odontotermes obesus (Macrotermitinae) mounds in the Indian Western Ghats forests

OpenAIRE

Shanbhag, R. R.; Kabbaj, M.; Sundararaj, R.; Jouquet, Pascal

2017-01-01

Several fungus-growing termite species build mounds, or termitaria, that are conspicuous features of African and Asian landscapes. Studies of the genus Macrotermes in Africa have established that their mounds provide an environment buffered against extremes of temperature and humidity, as well as protection from predators, and are correspondingly modified in composition. However, no studies are available in the specific context of the Asian continent where termite mounds are also abundant. He...

Contact area calculation between elastic solids bounded by mound rough surfaces

NARCIS (Netherlands)

Palasantzas, G

In this work, we investigate the influence of mound roughness on the contact area between elastic bodies. The mound roughness is described by the r.m.s. roughness amplitude w, the average mound separation Lambda, and the system correlation length xi. In general, the real contact area has a complex

Environmental assessment of the brine pipeline replacement for the Strategic Petroleum Reserve Bryan Mound Facility in Brazoria County, Texas

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

The Department of Energy (DOE) has prepared an environmental assessment (EA), DOE/EA-0804, for the proposed replacement of a deteriorated brine disposal pipeline from the Strategic Petroleum Reserve (SPR) Bryan Mound storage facility in Brazoria County, Texas, into the Gulf of Mexico. In addition, the ocean discharge outfall would be moved shoreward by locating the brine diffuser at the end of the pipeline 3.5 miles offshore at a minimum depth of 30 feet. The action would occur in a floodplain and wetlands; therefore, a floodplain/wetlands assessment has been prepared in conjunction with this EA. Based on the analyses in the EA, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969 (42 USC. 4321, et seg.). Therefore, the preparation of an Environmental Impact Statement (EIS) is not required, and the Department is issuing this Finding of No Significant Impact (FONSI). This FONSI also includes a Floodplain Statement of Findings in accordance with 10 CFR Part 1022.

Environmental assessment of the brine pipeline replacement for the Strategic Petroleum Reserve Bryan Mound Facility in Brazoria County, Texas

International Nuclear Information System (INIS)

1993-09-01

The Department of Energy (DOE) has prepared an environmental assessment (EA), DOE/EA-0804, for the proposed replacement of a deteriorated brine disposal pipeline from the Strategic Petroleum Reserve (SPR) Bryan Mound storage facility in Brazoria County, Texas, into the Gulf of Mexico. In addition, the ocean discharge outfall would be moved shoreward by locating the brine diffuser at the end of the pipeline 3.5 miles offshore at a minimum depth of 30 feet. The action would occur in a floodplain and wetlands; therefore, a floodplain/wetlands assessment has been prepared in conjunction with this EA. Based on the analyses in the EA, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969 (42 USC. 4321, et seg.). Therefore, the preparation of an Environmental Impact Statement (EIS) is not required, and the Department is issuing this Finding of No Significant Impact (FONSI). This FONSI also includes a Floodplain Statement of Findings in accordance with 10 CFR Part 1022

Use of termite mounds in geochemical exploration in North Ethiopia [rapid communication

Science.gov (United States)

Kebede, Fassil

2004-09-01

The geochemistry of the termite mounds was studied in lower Giba River basin, Kolla Tambien district, northern Ethiopia to show that they are useful in searching for metals. Specimens from the termite mounds and parent materials were collected to quantify gold, silver, copper, zinc, cobalt, manganese, iron and nickel. The results of the geochemical analysis of the samples indicated that these metals exist both in the termite mound and the parent material in the surrounding area. Correlation analysis shows that termite mounds and the parent materials are positively correlated for gold ( r = 0.75∗), copper ( r = 0.77∗), silver ( r = 0.56∗) and manganese ( r = 0.72). This positive correlation leads to the conclusion that there is a direct relation between the concentration of metals in termite mound and the parent rocks. Termite mounds can therefore be used as tools in exploring for these metals.

Characteristics and origin of Earth-mounds on the Eastern Snake River Plain, Idaho

International Nuclear Information System (INIS)

Tullis, J.A.

1995-09-01

Earth-mounds are common features on the Eastern Snake River Plain, Idaho. The mounds are typically round or oval in plan view, <0.5 m in height, and from 8 to 14 m in diameter. They are found on flat and sloped surfaces, and appear less frequently in lowland areas. The mounds have formed on deposits of multiple sedimentary environments. Those studied included alluvial gravel terraces along the Big Lost River (late Pleistocene/early Holocene age), alluvial fan segments on the flanks of the Lost River Range (Bull Lake and Pinedale age equivalents), and loess/slopewash sediments overlying basalt flows. Backhoe trenches were dug to allow characterization of stratigraphy and soil development. Each mound has features unique to the depositional and pedogenic history of the site; however, there are common elements to all mounds that are linked to the history of mound formation. Each mound has a open-quotes floorclose quotes of a sediment or basement rock of significantly different hydraulic conductivity than the overlying sediment. These paleosurfaces are overlain by finer-grained sediments, typically loess or flood-overbank deposits. Mounds formed in environments where a sufficient thickness of fine-grained sediment held pore water in a system open to the migration to a freezing front. Heaving of the sediment occurred by the growth of ice lenses. Mound formation occurred at the end of the Late Pleistocene or early in the Holocene, and was followed by pedogenesis. Soils in the mounds were subsequently altered by bioturbation, buried by eolian deposition, and eroded by slopewash runoff. These secondary processes played a significant role in maintaining or increasing the mound/intermound relief

Characteristics and origin of Earth-mounds on the Eastern Snake River Plain, Idaho

Energy Technology Data Exchange (ETDEWEB)

Tullis, J.A.

1995-09-01

Earth-mounds are common features on the Eastern Snake River Plain, Idaho. The mounds are typically round or oval in plan view, <0.5 m in height, and from 8 to 14 m in diameter. They are found on flat and sloped surfaces, and appear less frequently in lowland areas. The mounds have formed on deposits of multiple sedimentary environments. Those studied included alluvial gravel terraces along the Big Lost River (late Pleistocene/early Holocene age), alluvial fan segments on the flanks of the Lost River Range (Bull Lake and Pinedale age equivalents), and loess/slopewash sediments overlying basalt flows. Backhoe trenches were dug to allow characterization of stratigraphy and soil development. Each mound has features unique to the depositional and pedogenic history of the site; however, there are common elements to all mounds that are linked to the history of mound formation. Each mound has a {open_quotes}floor{close_quotes} of a sediment or basement rock of significantly different hydraulic conductivity than the overlying sediment. These paleosurfaces are overlain by finer-grained sediments, typically loess or flood-overbank deposits. Mounds formed in environments where a sufficient thickness of fine-grained sediment held pore water in a system open to the migration to a freezing front. Heaving of the sediment occurred by the growth of ice lenses. Mound formation occurred at the end of the Late Pleistocene or early in the Holocene, and was followed by pedogenesis. Soils in the mounds were subsequently altered by bioturbation, buried by eolian deposition, and eroded by slopewash runoff. These secondary processes played a significant role in maintaining or increasing the mound/intermound relief.

A Preliminary Study on Termite Mound Soil as Agricultural Soil for Crop Production in South West, Nigeria

Directory of Open Access Journals (Sweden)

O. E. Omofunmi

2017-08-01

Full Text Available It is a popular belief of the people in the Southern region of Nigeria that a land infested with termite usually brings prosperity to the land owner regardless of the type of its usage. Therefore, the present study assessed termite mounds soil properties which are important to crop production. Two soil samples were collected and their physical and chemical properties determined in accordance with American Public Health Association (APHA, 2005. Data were analyzed using descriptive statistics. The textural classes showed that the termite mound soil was sand clay loam while the surrounding soil was clay loam. This results revealed that: Termites’ activity induced significant chemical changes in the soil possible due to the materials used in building their nests. There was increase the concentrations of nitrogen, phosphorus, Potassium, calcium and magnesium higher in the termite’s mounds, while the micro-nutrients (zinc, iron and copper except sulphur and manganese lower in the soil infested by termites. There were significant differences (p ≥ 0.05 between termite mound soil and surrounding soil. It showed highly positive correlation between termite mound and surrounding soil (r= 0.92. The concentration of the soil properties around the termite mound are within the range of soil nutrients suitable for arable crop production. Termite mound soil is recommended to be used as an alternative to local farmers who cannot afford to buy expensive inorganic fertilizers.

Performance evaluation of termite-mound clay, concrete and steel silos for the storage of maize grains in the humid tropics

Science.gov (United States)

Inadequate storage facilities have contributed to severe maize postharvest losses in many developing countries. This study determined the potential of termite mound clay (TMC), a readily-available material in Nigeria, as a construction material for storage silos. The performance of the TMC silo was ...

Plant Mounds as Concentration and Stabilization Agents for Actinide Soil Contaminants in Nevada

Energy Technology Data Exchange (ETDEWEB)

D.S. Shafer; J. Gommes

2009-02-03

Plant mounds or blow-sand mounds are accumulations of soil particles and plant debris around the base of shrubs and are common features in deserts in the southwestern United States. An important factor in their formation is that shrubs create surface roughness that causes wind-suspended particles to be deposited and resist further suspension. Shrub mounds occur in some plant communities on the Nevada Test Site, the Nevada Test and Training Range (NTTR), and Tonopah Test Range (TTR), including areas of surface soil contamination from past nuclear testing. In the 1970s as part of early studies to understand properties of actinides in the environment, the Nevada Applied Ecology Group (NAEG) examined the accumulation of isotopes of Pu, 241Am, and U in plant mounds at safety experiment and storage-transportation test sites of nuclear devices. Although aerial concentrations of these contaminants were highest in the intershrub or desert pavement areas, the concentration in mounds were higher than in equal volumes of intershrub or desert pavement soil. The NAEG studies found the ratio of contaminant concentration of actinides in soil to be greater (1.6 to 2.0) in shrub mounds than in the surrounding areas of desert pavement. At Project 57 on the NTTR, 17 percent of the area was covered in mounds while at Clean Slate III on the TTR, 32 percent of the area was covered in mounds. If equivalent volumes of contaminated soil were compared between mounds and desert pavement areas at these sites, then the former might contain as much as 34 and 62 percent of the contaminant inventory, respectively. Not accounting for radionuclides associated with shrub mounds would cause the inventory of contaminants and potential exposure to be underestimated. In addition, preservation of shrub mounds could be important part of long-term stewardship if these sites are closed by fencing and posting with administrative controls.

The long term sustainability of Mound Springs in South Australia : implications for olympic dam

International Nuclear Information System (INIS)

Mudd, G.M.

1998-01-01

The Mound Springs of South Australia are unique groundwater discharge features of the Great Artesian Basin, a deep regigonal groundwater system that covers over one-fifth of the Australia continent. They are the principal sources of water in the arid and semi-arid inland heart of Australia, and have great ecological, scientific, anthropological and economic significance. Excessive development of the Great Artesian Basin over the past century by European activity has seen an overall decline in the flows from the mound springs, and recent development of the water supply borefields for the WMC Olympic Dam Operations copper-uranium mine in the midst of the most important spring groups has exacerbated this problem. A review of the history of the borefields, an analysis of the impacts on the mound springs, and future recommendations for protection of the springs is presented. (orig.)

Food preferences and mound-building behaviour of the mound-building mice Mus spicilegus

Science.gov (United States)

Hölzl, Michaela; Krištofík, Ján; Darolová, Alžbeta; Hoi, Herbert

2011-10-01

Optimal foraging strategies and food choice are influenced by various factors, e.g. availability, size and caloric content of the food type and predation risk. However, food choice criteria may change when food is not eaten immediately but has to be carried to a storage site for later use. For example, handling time in terms of harvesting and transport time should be optimized, particularly when the risk of predation is high. Thus, it is not clear whether food selected by hoarding animals reflects their food preference due to intrinsic features of the food type, e.g. size, caloric or lipid content, or whether the food type selected is a compromise that also considers the handling time required for harvesting and transport. We investigate this question in relation to food hoarding behaviour in mound-building mice. In autumn, mound-building mice Mus spicilegus collect seeds and other plant material and cover it with soil. Such above-ground storage is quite unusual for rodents. Here, we investigated whether there is a relationship between the seed species preferred as building materials and those preferred for food. We conducted a seed preference test using three most collected weed species for mound building. Controlling factors like food availability or predation risk, mice prefer Setaria spp. as food, although Amaranthus spp. and Chenopodium spp. were preferentially harvested and stored. By including the availability of the three species, our experimental results were confirmed, namely, a clear preference for Setaria spp. Also, handling time and seed size revealed to influence plant choice.

Design of radioisotope power systems facility

International Nuclear Information System (INIS)

Eschenbaum, R.C.; Wiemers, M.J.

1991-01-01

Radioisotope power systems currently produced for the U.S. Department of Energy Office of Special Applications by the Mound Laboratory at Miamisburg, Ohio, have been used in a variety of configurations by the Department of Defense and the National Aeronautics and Space Administration. A forecast of fugure radioisotope power systems requirements showed a need for an increased production rate beyond the capability of the existing Mound Laboratory. Westinghouse Hanford Company is modifying the Fuels and Materials Examination Facility on the Hanford Site near Richland, Washington, to install the new Radioisotope Power Systems Facility for assembling future radioisotope power systems. The facility is currently being prepared to assemble the radioisotope thermoelectric generators required by the National Aeronautics and Space Administration missions for Comet Rendezvous Asteroid Flyby in 1995 and Cassini, an investigation of Saturn and its moons, in 1996

Morphology and spatial patterns of Macrotermes mounds in the SE Katanga, D.R. Congo

Science.gov (United States)

Bazirake Mujinya, Basile; Mees, Florias; Erens, Hans; Baert, Geert; Van Ranst, Eric

2015-04-01

The spatial distribution patterns and morphological characteristics of Macrotermes falciger mounds were investigated in the Lubumbashi area, D.R. Congo. Examination of the spatial patterns of M. falciger mounds on high resolution satellite images reveals a mean areal number density of 2.9 ± 0.4 mounds ha-1. The high relative number of inactive mounds in the region, along with their regular distribution pattern, suggests that current termite mound occurrences are largely palaeostructures. Mound positions in the habitat are consistent with intraspecific competition rather than soil and substrate characteristics as controlling factor. Detailed morphological description of five deep termite-mound profiles (~7 m height/depth) shows that carbonate pedofeatures are present in all studied profiles, in contrast to the control soils. They mainly occur in the form of soft powdery masses, nodules and coatings on ped faces, all clearly pedogenic. Carbonate coatings occur mainly between 1 m above the soil surface and 1 m below that level in all mound profiles. Carbonate nodules do show a different distribution pattern at each site. Furthermore, when the studied profiles are considered to represent a toposequence, the stone layer occurs at greater depth in topographically low areas compared to crest and slope positions, which is mainly conditioned by erosion. The clay content of epigeal mounds increases from the summit to the toe slope, which can be largely related to differences in parent material. The Mn-Fe oxide concentrations occurring in all studied termite mound profiles reflect a seasonally high perched water table beneath the mound, which is more pronounced at the lower slope positions.

Transition and Closeout of the Former DOE Mound Plant Site: Lessons Learned

International Nuclear Information System (INIS)

Carpenter, C. P.; Marks, M. L.; Smiley, S.L.; Gallaher, D. M.

2006-01-01

The U.S. Department of Energy's (DOE's) Office of Environmental Management (EM) manages the Miamisburg Closure Project (MCP) by cleaning up the Mound site, located in Miamisburg, Ohio, to specific environmental standards, conveying all excess land parcels to the Miamisburg Mound Community Improvement Corporation, and transferring all continuing DOE post-closure responsibilities to the Office of Legacy Management (LM). Presently, the EM cleanup contract of the Mound site with CH2M Hill Mound Inc. is scheduled for completion on March 31, 2006. LM manages the Mound transition efforts and also post-closure responsibilities at other DOE sites via a contract with the S.M. Stoller Corporation. The programmatic transfer from EM to LM is scheduled to take place on October 1, 2006. The transition of the Mound site has required substantial integration and coordination between the EM and LM. Several project management principles have been implemented to help facilitate the transfer of programmatic responsibility. As a result, several lessons learned have been identified to help streamline and improve integration and coordination of the transfer process. Lessons learned from the Mound site transition project are considered a work in progress and have been summarized according to a work breakdown structure for specific functional areas in the transition schedule. The functional areas include program management, environmental, records management, information technology, property management, stakeholder and regulatory relations, procurement, worker pension and benefits, and project closeout. Specific improvements or best practices have been recognized and documented by the Mound transition team. The Mound site is one of three major cleanup sites within the EM organization scheduled for completion in 2006. EM, EM cleanup contractor, LM, and LM post-closure contractor have identified lessons learned during the transition and closure of the Mound site. The transition effort from

Geochemical prospecting for rare earth elements using termite mound materials

Science.gov (United States)

Horiuchi, Yu; Ohno, Tetsuji; Hoshino, Mihoko; Shin, Ki-Cheol; Murakami, Hiroyasu; Tsunematsu, Maiko; Watanabe, Yasushi

2014-12-01

The Blockspruit fluorite prospect, located in North West State of the Republic of South Africa, occurs within an actinolite rock zone that was emplaced into the Kenkelbos-type granite of Proterozoic age. There are a large number of termite mounds in the prospect. For geochemical prospecting for rare earth elements (REEs), in total, 200 samples of termite mound material were collected from actinolite rock and granite zones in the prospect. Geochemical analyses of these termite mound materials were conducted by two methods: portable X-ray fluorescence (XRF) spectrometry and inductively coupled plasma-mass spectrometry (ICP-MS). Comparison of the two methods broadly indicates positive correlations of REEs (La, Ce, Pr, Nd, and Y), in particular Y and La having a strong correlation. As the result of modal abundance analyses, the actinolite rock at surface mainly consists of ferro-actinolite (89.89 wt%) and includes xenotime (0.26 wt%) and monazite (0.21 wt%) grains as REE minerals. Termite mound materials from actinolite rock also contain xenotime (0.27 wt%) and monazite (0.41 wt%) grains. In addition, termite mound materials from the actinolite rock zone have high hematite and Fe silicate contents compared to those from granite zone. These relationships suggest that REE minerals in termite mound materials originate form actinolite rock. Geochemical anomaly maps of Y, La, and Fe concentrations drawn based on the result of the portable XRF analyses show that high concentrations of these elements trend from SW to NE which broadly correspond to occurrences of actinolite body. These results indicate that termite mounds are an effective tool for REE geochemical prospection in the study area for both light REEs and Y, but a more detailed survey is required to establish the distribution of the actinolite rock body.

Physiological and biogeochemical traits of bleaching and recovery in the mounding species of coral Porites lobata: implications for resilience in mounding corals.

Directory of Open Access Journals (Sweden)

Stephen J Levas

Full Text Available Mounding corals survive bleaching events in greater numbers than branching corals. However, no study to date has determined the underlying physiological and biogeochemical trait(s that are responsible for mounding coral holobiont resilience to bleaching. Furthermore, the potential of dissolved organic carbon (DOC as a source of fixed carbon to bleached corals has never been determined. Here, Porites lobata corals were experimentally bleached for 23 days and then allowed to recover for 0, 1, 5, and 11 months. At each recovery interval a suite of analyses were performed to assess their recovery (photosynthesis, respiration, chlorophyll a, energy reserves, tissue biomass, calcification, δ(13C of the skeletal, δ(13C, and δ(15N of the animal host and endosymbiont fractions. Furthermore, at 0 months of recovery, the assimilation of photosynthetically acquired and zooplankton-feeding acquired carbon into the animal host, endosymbiont, skeleton, and coral-mediated DOC were measured via (13C-pulse-chase labeling. During the first month of recovery, energy reserves and tissue biomass in bleached corals were maintained despite reductions in chlorophyll a, photosynthesis, and the assimilation of photosynthetically fixed carbon. At the same time, P. lobata corals catabolized carbon acquired from zooplankton and seemed to take up DOC as a source of fixed carbon. All variables that were negatively affected by bleaching recovered within 5 to 11 months. Thus, bleaching resilience in the mounding coral P. lobata is driven by its ability to actively catabolize zooplankton-acquired carbon and seemingly utilize DOC as a significant fixed carbon source, facilitating the maintenance of energy reserves and tissue biomass. With the frequency and intensity of bleaching events expected to increase over the next century, coral diversity on future reefs may favor not only mounding morphologies but species like P. lobata, which have the ability to utilize heterotrophic

Beads from Inhumation Rite Burials of Gnezdovo Burial Mound

Directory of Open Access Journals (Sweden)

Dobrova Olga P.

2017-12-01

Full Text Available The beads from 33 inhumation burials at Gnezdovo burial mound are examined in the article. The beads (total 367 were crafted from stretched tube (258, stretched stick (3, winding (45, press molding (2 pcs., welding (2 pcs., and mosaic beads (9 pcs.. The burial mound contains virtually no broken beads, including the settlement's most common yellow glass beads. Besides glass beads, cornelian, crystal, amber and faience beads have been registered among the burial mound material, as well as beads crafted with metal. Apart from beads, grave inventories contained a series of pendants with a bead strung on a wire ring. The considered complexes contain five pendants of this type. Besides Gnezdovo, similar pendants have been discovered in Kiev, Timerev, Pskov and Vladimir barrows. A comparison between bead sets from Gnezdovo and Kiev burial mounds allows to conclude that the general composition and occurrence frequency of beads is identical for these burials. At the same time, beads crafted with rock crystal, cornelian and metal are more frequently discovered in Kiev inhumations.

"Magnetic" termite mound surfaces are oriented to suit wind and shade conditions.

Science.gov (United States)

Jacklyn, Peter M

1992-09-01

The termites Amitermes meridionalis and A. laurensis construct remarkable meridional or "magnetic" mounds in northern Australia. These mounds vary geographically in mean orientation in a manner that suggests such variation is an adaptive response to local environmental conditions. Theoretical modelling of solar irradiance and mound rotation experiments show that maintenance of an eastern face temperature plateau during the dry season is the most likely physical basis for the mound orientation response. Subsequent heat transfer analysis shows that habitat wind speed and shading conditions also affect face temperature gradients such as the rate of eastern face temperature change. It is then demonstrated that the geographic variation in mean mound orientation follows the geographic variation in long-term wind speed and shading conditions across northern Australia such that an eastern face temperature plateau is maintained in all locations.

Safety Oversight of Decommissioning Activities at DOE Nuclear Sites

International Nuclear Information System (INIS)

Zull, Lawrence M.; Yeniscavich, William

2008-01-01

The Defense Nuclear Facilities Safety Board (Board) is an independent federal agency established by Congress in 1988 to provide nuclear safety oversight of activities at U.S. Department of Energy (DOE) defense nuclear facilities. The activities under the Board's jurisdiction include the design, construction, startup, operation, and decommissioning of defense nuclear facilities at DOE sites. This paper reviews the Board's safety oversight of decommissioning activities at DOE sites, identifies the safety problems observed, and discusses Board initiatives to improve the safety of decommissioning activities at DOE sites. The decommissioning of former defense nuclear facilities has reduced the risk of radioactive material contamination and exposure to the public and site workers. In general, efforts to perform decommissioning work at DOE defense nuclear sites have been successful, and contractors performing decommissioning work have a good safety record. Decommissioning activities have recently been completed at sites identified for closure, including the Rocky Flats Environmental Technology Site, the Fernald Closure Project, and the Miamisburg Closure Project (the Mound site). The Rocky Flats and Fernald sites, which produced plutonium parts and uranium materials for defense needs (respectively), have been turned into wildlife refuges. The Mound site, which performed R and D activities on nuclear materials, has been converted into an industrial and technology park called the Mound Advanced Technology Center. The DOE Office of Legacy Management is responsible for the long term stewardship of these former EM sites. The Board has reviewed many decommissioning activities, and noted that there are valuable lessons learned that can benefit both DOE and the contractor. As part of its ongoing safety oversight responsibilities, the Board and its staff will continue to review the safety of DOE and contractor decommissioning activities at DOE defense nuclear sites

The Surales, Self-Organized Earth-Mound Landscapes Made by Earthworms in a Seasonal Tropical Wetland.

Directory of Open Access Journals (Sweden)

Anne Zangerlé

Full Text Available The formation, functioning and emergent properties of patterned landscapes have recently drawn increased attention, notably in semi-arid ecosystems. We describe and analyze a set of similarly spectacular landforms in seasonal tropical wetlands. Surales landscapes, comprised of densely packed, regularly spaced mounds, cover large areas of the Orinoco Llanos. Although descriptions of surales date back to the 1940's, their ecology is virtually unknown. From data on soil physical and chemical properties, soil macrofauna, vegetation and aerial imagery, we provide evidence of the spatial extent of surales and how they form and develop. Mounds are largely comprised of earthworm casts. Recognizable, recently produced casts account for up to one-half of total soil mass. Locally, mounds are relatively constant in size, but vary greatly across sites in diameter (0.5-5 m and height (from 0.3 m to over 2 m. This variation appears to reflect a chronosequence of surales formation and growth. Mound shape (round to labyrinth varies across elevational gradients. Mounds are initiated when large earthworms feed in shallowly flooded soils, depositing casts that form 'towers' above water level. Using permanent galleries, each earthworm returns repeatedly to the same spot to deposit casts and to respire. Over time, the tower becomes a mound. Because each earthworm has a restricted foraging radius, there is net movement of soil to the mound from the surrounding area. As the mound grows, its basin thus becomes deeper, making initiation of a new mound nearby more difficult. When mounds already initiated are situated close together, the basin between them is filled and mounds coalesce to form larger composite mounds. Over time, this process produces mounds up to 5 m in diameter and 2 m tall. Our results suggest that one earthworm species drives self-organizing processes that produce keystone structures determining ecosystem functioning and development.

The Surales, Self-Organized Earth-Mound Landscapes Made by Earthworms in a Seasonal Tropical Wetland.

Science.gov (United States)

Zangerlé, Anne; Renard, Delphine; Iriarte, José; Suarez Jimenez, Luz Elena; Adame Montoya, Kisay Lorena; Juilleret, Jérôme; McKey, Doyle

2016-01-01

The formation, functioning and emergent properties of patterned landscapes have recently drawn increased attention, notably in semi-arid ecosystems. We describe and analyze a set of similarly spectacular landforms in seasonal tropical wetlands. Surales landscapes, comprised of densely packed, regularly spaced mounds, cover large areas of the Orinoco Llanos. Although descriptions of surales date back to the 1940's, their ecology is virtually unknown. From data on soil physical and chemical properties, soil macrofauna, vegetation and aerial imagery, we provide evidence of the spatial extent of surales and how they form and develop. Mounds are largely comprised of earthworm casts. Recognizable, recently produced casts account for up to one-half of total soil mass. Locally, mounds are relatively constant in size, but vary greatly across sites in diameter (0.5-5 m) and height (from 0.3 m to over 2 m). This variation appears to reflect a chronosequence of surales formation and growth. Mound shape (round to labyrinth) varies across elevational gradients. Mounds are initiated when large earthworms feed in shallowly flooded soils, depositing casts that form 'towers' above water level. Using permanent galleries, each earthworm returns repeatedly to the same spot to deposit casts and to respire. Over time, the tower becomes a mound. Because each earthworm has a restricted foraging radius, there is net movement of soil to the mound from the surrounding area. As the mound grows, its basin thus becomes deeper, making initiation of a new mound nearby more difficult. When mounds already initiated are situated close together, the basin between them is filled and mounds coalesce to form larger composite mounds. Over time, this process produces mounds up to 5 m in diameter and 2 m tall. Our results suggest that one earthworm species drives self-organizing processes that produce keystone structures determining ecosystem functioning and development.

The Surales, Self-Organized Earth-Mound Landscapes Made by Earthworms in a Seasonal Tropical Wetland

Science.gov (United States)

Iriarte, José; Suarez Jimenez, Luz Elena; Adame Montoya, Kisay Lorena; Juilleret, Jérôme; McKey, Doyle

2016-01-01

The formation, functioning and emergent properties of patterned landscapes have recently drawn increased attention, notably in semi-arid ecosystems. We describe and analyze a set of similarly spectacular landforms in seasonal tropical wetlands. Surales landscapes, comprised of densely packed, regularly spaced mounds, cover large areas of the Orinoco Llanos. Although descriptions of surales date back to the 1940’s, their ecology is virtually unknown. From data on soil physical and chemical properties, soil macrofauna, vegetation and aerial imagery, we provide evidence of the spatial extent of surales and how they form and develop. Mounds are largely comprised of earthworm casts. Recognizable, recently produced casts account for up to one-half of total soil mass. Locally, mounds are relatively constant in size, but vary greatly across sites in diameter (0.5–5 m) and height (from 0.3 m to over 2 m). This variation appears to reflect a chronosequence of surales formation and growth. Mound shape (round to labyrinth) varies across elevational gradients. Mounds are initiated when large earthworms feed in shallowly flooded soils, depositing casts that form ‘towers’ above water level. Using permanent galleries, each earthworm returns repeatedly to the same spot to deposit casts and to respire. Over time, the tower becomes a mound. Because each earthworm has a restricted foraging radius, there is net movement of soil to the mound from the surrounding area. As the mound grows, its basin thus becomes deeper, making initiation of a new mound nearby more difficult. When mounds already initiated are situated close together, the basin between them is filled and mounds coalesce to form larger composite mounds. Over time, this process produces mounds up to 5 m in diameter and 2 m tall. Our results suggest that one earthworm species drives self-organizing processes that produce keystone structures determining ecosystem functioning and development. PMID:27168157

Environmental assessment for commercialization of the Mound Plant

International Nuclear Information System (INIS)

1994-01-01

In November 1993 US DOE decided to phase out operations at the Mound Plant in Miamisburg, Ohio, with the goal of releasing the site for commercial use. The broad concept is to transform the plant into an advanced manufacturing center with the main focus on commercializing products and other technology. DOE proposes to lease portions of the Mound Plant to commercial enterprises. This Environmental Impact statement has a finding of no significant impact in reference to such action

Methane oxidation by termite mounds estimated by the carbon isotopic composition of methane

Science.gov (United States)

Sugimoto, Atsuko; Inoue, Tetsushi; Kirtibutr, Nit; Abe, Takuya

1998-12-01

Emission rates and carbon isotope ratios of CH4, emitted by workers of termites, and of CH4, emitted from their mounds, were observed in a dry evergreen forest in Thailand to estimate the proportion of CH4 oxidized during emission through the mound. The δ13C of CH4 emitted from a termite mound (-70.9 to -82.4‰) was higher than that of CH4 emitted by workers in the mound (-85.4 to -97. l‰). Using a fractionation factor (a = 0.987) for oxidation of CH4 which was obtained in the incubation experiment, an emission factor defined as (CH4 emitted from a termite mound/CH4 produced by termites) was calculated. The emission factor obtained in each termite mound was nearly zero for Macrotermes (fungus-growing termites), of which the nest has a thick soil wall and subterrannean termites, and 0.17 to 0.47 for Termitinae (small-mound-making termites). Global CH4 emission by termites was estimated on the basis of the CH4 emission rates by workers and termite biomass with the emission factors. The calculated result was 1.5 to 7.4 Tg/y (0.3 to 1.3% of total source), which is considerably smaller than the estimate by the IPCC [1994].

Upper Silurian reef mounds on a shallowing carbonate ramp, Devon Island, Arctic Canada

Energy Technology Data Exchange (ETDEWEB)

Dixon, O A [Ottawa Univ., ON (Canada); Graf, G C [Chevron Canada Resources, Calgary, AB (Canada)

1992-03-01

Near Gascoyne Inlet, the topmost Douro and lowermost Barlow Inlet formations record overall upward shallowing from ramp to shallow shelf conditions. This transitional sequence contains bioherms of various sizes, from small isolated reef mounds 1-2 m across to larger, compound reef mounds over 50 m thick and 60 m across, as well as distictive inter- and pre-reef mound facies. The larger reef mounds show stages intermediate in character between those in sponge-dominated reef mounds of the Douro Formation and in larger stromatoporoid-crinoid dominated reefs in the Barlow Inlet Formation. Three principal reef mounds developed in turn. An initial partly lithified lime mudstone, containing scattered corals and apparently relict sponge-cryptomicrobial fabrics, developed on sheets of oncolitic storm debris in mainly low energy conditions between storm and fairweather wave bases. With gradual shallowing and progressively higher energy conditions above fairweather wave base, a middle facies of coral- and crinoid-rich mudstone developed. An abrupt deepening restored conditions of low energy, and the ensuing upper facies of the reef mounds is more varied, comprising sparsely fossiliferous and locally fenestral lime mudstones, patchy coral bafflestone and bindstone, coarse encrinites and substantially culminating stromatoporoid bindstone. 36 refs., 14 figs., 5 tabs.

Monthly fluctuation of termite caste proportions (Isoptera) within fire ant mounds (hymenoptera: formicidae)

Science.gov (United States)

Thomas G. Shelton; J.T. Vogt; Marla J. Tanley; Arthur G. Appel

2003-01-01

Monthly abundance and caste proportions of subterranean termites (Reticulitennes spp.) inhabiting red imported fire ant (Solenopsis invicta Buren) mounds were recorded during 1999 and 2000 from a relatively undisturbed forest edge in Tuskegee, Alabama. Temperature data were also recorded at these mounds; mean air, soil, and mound temperatures followed a sine model over...

Environmental assessment of coal waste mounds in Japan using remote sensing techniques

Energy Technology Data Exchange (ETDEWEB)

Lewis, A J; Gotoh, K; Aoyama, K; Aoki, S [Louisiana State University, Baton Rouge, LA (United States). Department of Geography and Anthropology

1993-01-01

Focuses on the application of remote sensing techniques to the study of coal waste mounds. The situation at the coal waste mounds in Fukuoka, Japan is cited. Guidelines on film parameters, photographic keys and tasks required to inventory, monitor and manage coal waste mounds in Japan are addressed. Application of photogrammetry, remote sensing, aerial photography and satellite imagery techniques in monitoring spoil banks is reviewed. Applicability of the techniques is discussed. 24 refs.

The relationships between termite mound CH4/CO2 emissions and internal concentration ratios are species specific

Directory of Open Access Journals (Sweden)

H. Jamali

2013-04-01

Full Text Available We investigated the relative importance of CH4 and CO2 fluxes from soil and termite mounds at four different sites in the tropical savannas of northern Australia near Darwin and assessed different methods to indirectly predict CH4 fluxes based on CO2 fluxes and internal gas concentrations. The annual flux from termite mounds and surrounding soil was dominated by CO2 with large variations among sites. On a carbon dioxide equivalent (CO2-e basis, annual CH4 flux estimates from termite mounds were 5- to 46-fold smaller than the concurrent annual CO2 flux estimates. Differences between annual soil CO2 and soil CH4 (CO2-e fluxes were even greater, soil CO2 fluxes being almost three orders of magnitude greater than soil CH4 (CO2-e fluxes at site. The contribution of CH4 and CO2 emissions from termite mounds to the total CH4 and CO2 emissions from termite mounds and soil in CO2-e was less than 1%. There were significant relationships between mound CH4 flux and mound CO2 flux, enabling the prediction of CH4 flux from measured CO2 flux; however, these relationships were clearly termite species specific. We also observed significant relationships between mound flux and gas concentration inside mound, for both CH4 and CO2, and for all termite species, thereby enabling the prediction of flux from measured mound internal gas concentration. However, these relationships were also termite species specific. Using the relationship between mound internal gas concentration and flux from one species to predict mound fluxes from other termite species (as has been done in the past would result in errors of more than 5-fold for mound CH4 flux and 3-fold for mound CO2 flux. This study highlights that CO2 fluxes from termite mounds are generally more than one order of magnitude greater than CH4 fluxes. There are species-specific relationships between CH4 and CO2 fluxes from a mound, and between the inside mound concentration of a gas and the mound flux emission of the

The relationships between termite mound CH4/CO2 emissions and internal concentration ratios are species specific

Science.gov (United States)

Jamali, H.; Livesley, S. J.; Hutley, L. B.; Fest, B.; Arndt, S. K.

2013-04-01

We investigated the relative importance of CH4 and CO2 fluxes from soil and termite mounds at four different sites in the tropical savannas of northern Australia near Darwin and assessed different methods to indirectly predict CH4 fluxes based on CO2 fluxes and internal gas concentrations. The annual flux from termite mounds and surrounding soil was dominated by CO2 with large variations among sites. On a carbon dioxide equivalent (CO2-e) basis, annual CH4 flux estimates from termite mounds were 5- to 46-fold smaller than the concurrent annual CO2 flux estimates. Differences between annual soil CO2 and soil CH4 (CO2-e) fluxes were even greater, soil CO2 fluxes being almost three orders of magnitude greater than soil CH4 (CO2-e) fluxes at site. The contribution of CH4 and CO2 emissions from termite mounds to the total CH4 and CO2 emissions from termite mounds and soil in CO2-e was less than 1%. There were significant relationships between mound CH4 flux and mound CO2 flux, enabling the prediction of CH4 flux from measured CO2 flux; however, these relationships were clearly termite species specific. We also observed significant relationships between mound flux and gas concentration inside mound, for both CH4 and CO2, and for all termite species, thereby enabling the prediction of flux from measured mound internal gas concentration. However, these relationships were also termite species specific. Using the relationship between mound internal gas concentration and flux from one species to predict mound fluxes from other termite species (as has been done in the past) would result in errors of more than 5-fold for mound CH4 flux and 3-fold for mound CO2 flux. This study highlights that CO2 fluxes from termite mounds are generally more than one order of magnitude greater than CH4 fluxes. There are species-specific relationships between CH4 and CO2 fluxes from a mound, and between the inside mound concentration of a gas and the mound flux emission of the same gas, but

Design of the Long-term Waste Management Facility for Historic LLRW Port Hope Project - 13322

International Nuclear Information System (INIS)

Campbell, Don; Barton, David; Case, Glenn

2013-01-01

The Municipality of Port Hope is located on the northern shores of Lake Ontario approximately 100 km east of Toronto, Ontario, Canada. Starting in the 1930's, radium and later uranium processing by Eldorado Gold Mines Limited (subsequently Eldorado Nuclear Limited) (Eldorado) at their refinery in Port Hope resulted in the generation of process residues and wastes that were disposed of indiscriminately throughout the Municipality until about the mid-1950's. These process residues contained radium (Ra- 226), uranium, arsenic and other contaminants. Between 1944 and 1988, Eldorado was a Federal Crown Corporation, and as such, the Canadian Federal Government has assumed responsibility for the clean-up and long-term management of the historic waste produced by Eldorado during this period. The Port Hope Project involves the construction and development of a new long-term waste management facility (LTWMF), and the remediation and transfer of the historic wastes located within the Municipality of Port Hope to the new LTWMF. The new LTWMF will consist of an engineered above-ground containment mound designed to contain and isolate the wastes from the surrounding environment for the next several hundred years. The design of the engineered containment mound consists of a primary and secondary composite base liner system and composite final cover system, made up of both natural materials (e.g., compacted clay, granular materials) and synthetic materials (e.g., geo-synthetic clay liner, geo-membrane, geo-textiles). The engineered containment mound will cover an area of approximately 13 hectares and will contain the estimated 1.2 million cubic metres of waste that will be generated from the remedial activities within Port Hope. The LTWMF will also include infrastructure and support facilities such as access roads, administrative offices, laboratory, equipment and personnel decontamination facilities, waste water treatment plant and other ancillary facilities. Preliminary

Design of the Long-term Waste Management Facility for Historic LLRW Port Hope Project - 13322

Energy Technology Data Exchange (ETDEWEB)

Campbell, Don; Barton, David [Conestoga-Rovers and Associates, 651 Colby Drive, Waterloo, Ontario N2V 1C2 (Canada); Case, Glenn [Atomic Energy of Canada Limited, 115 Toronto Road, Port Hope, Ontario L1A 3S4 (Canada)

2013-07-01

The Municipality of Port Hope is located on the northern shores of Lake Ontario approximately 100 km east of Toronto, Ontario, Canada. Starting in the 1930's, radium and later uranium processing by Eldorado Gold Mines Limited (subsequently Eldorado Nuclear Limited) (Eldorado) at their refinery in Port Hope resulted in the generation of process residues and wastes that were disposed of indiscriminately throughout the Municipality until about the mid-1950's. These process residues contained radium (Ra- 226), uranium, arsenic and other contaminants. Between 1944 and 1988, Eldorado was a Federal Crown Corporation, and as such, the Canadian Federal Government has assumed responsibility for the clean-up and long-term management of the historic waste produced by Eldorado during this period. The Port Hope Project involves the construction and development of a new long-term waste management facility (LTWMF), and the remediation and transfer of the historic wastes located within the Municipality of Port Hope to the new LTWMF. The new LTWMF will consist of an engineered above-ground containment mound designed to contain and isolate the wastes from the surrounding environment for the next several hundred years. The design of the engineered containment mound consists of a primary and secondary composite base liner system and composite final cover system, made up of both natural materials (e.g., compacted clay, granular materials) and synthetic materials (e.g., geo-synthetic clay liner, geo-membrane, geo-textiles). The engineered containment mound will cover an area of approximately 13 hectares and will contain the estimated 1.2 million cubic metres of waste that will be generated from the remedial activities within Port Hope. The LTWMF will also include infrastructure and support facilities such as access roads, administrative offices, laboratory, equipment and personnel decontamination facilities, waste water treatment plant and other ancillary facilities

The occurrence and development of peat mounds on King George Island (Maritime Antarctic

Directory of Open Access Journals (Sweden)

Jerzy Fabiszewski

2014-01-01

Full Text Available On King George Island, South Shetlands Islands, a type of peat formation has been discovered which has not previously been reported from the Antarctic. These formations are in shape of mounds up to 7x 15 m in area, with a peat layer of about I m thick. About twenty five cm below the surface there is a layer of permanently frozen peat. The mounds are covered by living mosses (Polytrichum alpinum and Drepanocladus uncinatus, Antarctic hair grass (Deschampsia antarctica and lichens. Erosion fissures occurring on the surface are evidence of contemporary drying and cessation of the mound's growth. The initial phase of the development of the mounds began with a community dominated by Calliergidium austro-stramineum and Deschampsia antarctica, and their further development has been due to peat accumulation formed almost entirely by Calliergidium. The location of the mounds is near a penguin rookery, which clearly conditioned the minerotrophic character of these formations, as compared with the "moss peat banks" formed by Chorisodontium aciphyllum and Polytrichum al-pestre. Moreover, the peat mounds differ from the latter in several ways, e.g. rate of growth and floristic composition. Radiocarbon dating of peat from the base of one mound gave an age of 4090±60 years B.P. This suggests that the age of the tundra on King George Island is about 5000-4000 years.

Stability Of Rubble Mound Breakwaters Using High Density Rock

DEFF Research Database (Denmark)

Burcharth, H. F.; Beck, J. B.

2000-01-01

The present paper discusses the effect of mass density on stability of rubble mound breakwaters. A short literature review of existing knowledge is give to establish a background for the ongoing research. Furthermore, several model tests are described in which the stability of rubble mound...... breakwaters with armour stones of different densities are investigated. The results from the model test are discussed with respect to application and further research....

The giant cold-water coral mound as a nested microbial/metazoan system: physical, chemical, biological and geological picture (ESF EuroDiversity MiCROSYSTEMS)

Science.gov (United States)

Henriet, J. P.; Microsystems Team

2009-04-01

carbonate is derived from corals and suggests a selective enrichment of the hemipelagic carbonate fraction, compared to adjacent sediment drift deposits. • The detection of allochthonous fluids, in particular brines, in the pore space of the surficial mound sediments on the Pen Duick Escarpment hints towards the presence of salt deposits deep underneath, and simultaneously provides the first direct evidence of advective fluid transfer from the deep, throughout the mound substrate and the full mound height. Potential stratigraphic pathways leading from the deeper basinal realms directly to the mound setting have been imaged in a spectacular way through high-resolution pseudo-3D seismic imaging. Geophysical signatures of free gas accumulations have been detected a few hundreds of meters below the mound base, but low concentrations of methane and the absence of lipid biomarkers from methane-dependent prokaryotes suggest low fluxes of methane-derived carbon and thus very small rates of anaerobic oxidation of methane (AOM) in the immediate mound subsurface. Local changes in the sediment biogeochemistry are most likely dictated by slow diffusive fluid transfer, operating in a heterogeneous way in the subsurface. • Cultivation experiments with sediments from microbially active mound zones have allowed to study microbially induced carbonate precipitation and provide a tool for the interpretation of carbonate mineralogy. The development and operation of a continuous high-pressure bioreactor (100 bars) allows to simulate in an ex situ mode the impact of environmental parameter changes onto the functioning of relevant microbial communities. • The detected influx of sulfate in mound sediments implies that bacterial sulfate reduction can be the dominant anaerobic carbon mineralization process. Groundwater flow modeling suggests that currents impinging on the escarpment and the flanks of an exposed mound can account for a significant influx and transport of sulfate through

An overview of plutonium-238 decontamination and decommissioning (D and D) projects at Mound

International Nuclear Information System (INIS)

Bond, W.H.; Davis, W.P.; Draper, D.G.; Geichman, J.R.; Harris, J.C.; Jaeger, R.R.; Sohn, R.L.

1987-01-01

Mound is currently decontaminating for restricted reuse and/or decommissioning for conditional release four major plutonium-238 contaminated facilities that contained 1700 linear feet of gloveboxes and associated equipment and services. Several thousand linear feet of external underground piping, associated tanks, and contaminated soil are being removed. Two of the facilities contain ongoing operations and will be reused for both radioactive and nonradioactive programs. Two others will be completely demolished and the land area will become available for future DOE building sites. An overview of the successful techniques and equipment used in the decontamination and decommissioning of individual pieces of equipment, gloveboxes, services, laboratories, sections of buildings, entire buildings, and external underground piping, tanks, and soil in a highly populated residential area is described and pictorially presented

Permanent groundwater storage in basaltic dyke fractures and termite mound viability

Science.gov (United States)

Mège, Daniel; Rango, Tewodros

2010-04-01

Many basaltic dykes of the Ethiopian flood basalt province are observed in the northwestern Ethiopian lowlands. In this area, the termites preferentially build their epigeous mounds on the top of dolerite dykes. The relationship between termite mounds and dykes is investigated from the analysis of their distribution along one of these dykes, of thickness 2-5 m, that we could follow over 2000 m. Termite mounds are periodically spaced (mean distance 63 m, R2 = 0.995), and located exclusively where the topographic relief of the dyke is not more than 2 m above the surrounding area. From these observations and from the geological context, a hydrological circuit model is proposed in which (1) dykes are preferential conduits for groundwater drainage during the rainy season due to pervasive jointing, (2) during the dry season, the portion of the dyke forming a local topographic relief area dries up more quickly than the surroundings, the elevation difference between the dyke summit and the surroundings being a factor restricting termite mound development. For dyke topographic relief >2 m, drying is an obstacle for maintaining the appropriate humidity for the termite colony life. Periodic termite mound spacing is unlikely to be related to dyke or other geological properties. It is more likely related to termite population behaviour, perhaps to clay shortage, which restricts termite population growth by limiting the quantity of building material available for mound extension, and triggers exploration for a new colonization site that will be located along the dyke at a distance from the former colony that may be controlled by the extent of the zone covered by its trail pheromones. This work brings out the importance of dykes in channelling and storing groundwater in semiarid regions, and shows that dykes can store groundwater permanently in such settings even though the dry season is half the year long. It contributes also to shedding light on water supply conditions

Sub-kilometre (intra-crater) mounds in Utopia Planitia, Mars: character, occurrence and possible formation hypotheses

Science.gov (United States)

Soare, Richard J.; Conway, Susan J.; Pearce, Geoffrey D.; Costard, François; Séjourné, Antoine

2013-08-01

At the middle latitudes of Utopia Planitia (˜35-45°N; ˜65-101°E) hundreds of small-sized mounds located in sub-kilometre impact craters dot the landscape. Their shape varies from circular to crescentic and their height ranges from ˜10 to 50 m. Often, metre to decametre pitting is observed, as is metres-thick banding or stratification. Mound albedo is relatively high, i.e. ˜0.16. The plain's terrain in the region, previously linked to the latitude-dependent mantle (LDM) of ice-dust, displays pitting and albedo similar to the small intra-crater mounds. Some workers have suggested that the mounds and the plain's terrain share a common ice-dust origin. If so, then scrutinising the mounds could provide analogical insight on the key geological characteristics and spatial distribution of the LDM itself. Other workers have hypothesised that the mounds are eroded sedimentary landforms or periglacial mounds underlain by a perennial ice-core (closed-system pingos). In this article we develop and then discuss each of the three mound-hypotheses in a much more substantial manner than has been done hitherto. Towards this end we use high-resolution images, present a detailed regional-map of mound distribution and establish a regional platform of topographical analysis using MOLA data superposed on a large-scale CTX mosaic. Although the ice-dust hypothesis is consistent with some observations and measurements, we find that a (loess-based) sedimentary hypothesis shows greater plausibility. Of the three hypotheses evaluated, the pingo or periglacial one is the weakest.

Molluskan fauna in two shell mounds in the State of Parana coast, Brazil

Directory of Open Access Journals (Sweden)

Marcos de Vasconcellos Gernet

2011-09-01

Full Text Available The shell mounds are artificial formations consisting mostly of mollusk shells used in the feeding of the prehistoric peoples which inhabited our coast. These sites are found throughout the Brazilian coast, and hundreds of them were cataloged in the State of Paraná since the 1940s. The fragility of these sites, their importance as evidences of our prehistoric period, and its abrupt disappearance, justify the need for new researches which contribute to contextualize and draw up plans to preserve this heritage. The works related to the molluskan fauna found in the shell mounds are restricted to refer to the most common species and, sometimes, just their popular names. A greater knowledge on these prehistoric inhabitants’ diet allows a better understanding of ancient natural ecosystems. The survey of mollusks was carried out in the shell mounds Guaraguaçu and Boguaçu, in the towns of Pontal do Parana and Guaratuba, respectively, and performed through visual inspection, reading of specialized bibliography and comparison to previous works on the fauna of the shell mounds in the State of Parana coast. Altogether, 29 species were observed in the shell mound Guaraguaçu and 17 species were observed in the shell mound Boguaçu, resulting in a total of 31 species.

Estimating Groundwater Mounding in Sloping Aquifers for Managed Aquifer Recharge.

Science.gov (United States)

Zlotnik, Vitaly A; Kacimov, Anvar; Al-Maktoumi, Ali

2017-11-01

Design of managed aquifer recharge (MAR) for augmentation of groundwater resources often lacks detailed data, and simple diagnostic tools for evaluation of the water table in a broad range of parameters are needed. In many large-scale MAR projects, the effect of a regional aquifer base dip cannot be ignored due to the scale of recharge sources (e.g., wadis, streams, reservoirs). However, Hantush's (1967) solution for a horizontal aquifer base is commonly used. To address sloping aquifers, a new closed-form analytical solution for water table mound accounts for the geometry and orientation of recharge sources at the land surface with respect to the aquifer base dip. The solution, based on the Dupiuit-Forchheimer approximation, Green's function method, and coordinate transformations is convenient for computing. This solution reveals important MAR traits in variance with Hantush's solution: mounding is limited in time and space; elevation of the mound is strongly affected by the dip angle; and the peak of the mound moves over time. These findings have important practical implications for assessment of various MAR scenarios, including waterlogging potential and determining proper rates of recharge. Computations are illustrated for several characteristic MAR settings. © 2017, National Ground Water Association.

The relationship between termite mound CH4/CO2 emissions and internal concentration ratios are species specific

Science.gov (United States)

Jamali, H.; Livesley, S. J.; Hutley, L. B.; Fest, B.; Arndt, S. K.

2012-12-01

1. We investigated the relative importance of CH4 and CO2 fluxes from soil and termite mounds at four different sites in the tropical savannas of Northern Australia near Darwin and assessed different methods to indirectly predict CH4 fluxes based on CO2 fluxes and internal gas concentrations. 2. The annual flux from termite mounds and surrounding soil was dominated by CO2 with large variations among sites. On a CO2-e basis, annual CH4 flux estimates from termite mounds were 5- to 46-fold smaller than the concurrent annual CO2 flux estimates. Differences between annual soil CO2 and soil CH4 (CO2-e) fluxes were even greater, soil CO2 fluxes being almost three orders of magnitude greater than soil CH4 (CO2-e) fluxes at site. 3. There were significant relationships between mound CH4 flux and mound CO2 flux, enabling the prediction of CH4 flux from measured CO2 flux, however, these relationships were clearly termite species specific. 4. We also observed significant relationships between mound flux and gas concentration inside mound, for both CH4 and CO2, and for all termite species, thereby enabling the prediction of flux from measured mound internal gas concentration. However, these relationships were also termite species specific. Using the relationship between mound internal gas concentration and flux from one species to predict mound fluxes from other termite species (as has been done in past) would result in errors of more than 5-fold for CH4 and 3-fold for CO2. 5. This study highlights that CO2 fluxes from termite mounds are generally more than one order of magnitude greater than CH4 fluxes. There are species-specific relationships between CH4 and CO2 fluxes from a~mound, and between the inside mound concentration of a gas and the mound flux emission of the same gas, but these relationships vary greatly among termite species. Consequently, there is no generic relationship that will allow for the prediction of CH4 fluxes from termite mounds of all species.

Greener management practices - ash mound reclamation

Energy Technology Data Exchange (ETDEWEB)

Kapur, S.L.; Shyam, A.K.; Soni, R. [National Thermal Power Corp. Ltd., New Delhi (India)

2002-12-01

The dry ash handling system at Dadri has been pioneered for the first time in India by the National Thermal Power Corporation (NTPC). The system is similar to that at the Drax power station in England. The paper reports the successful experimental trials carried out on vegetation of temporary ash mounds to assess the growth potential of local herbs, shrubs, trees and grasses directly on ash with no soil cover or fertiliser. These were extended to trials directly on the available (completed) mound surfaces. The grass Cynodon dactylon germinated well as did seeds of tree species including the Casurarina and Eucalyptus. It is hoped that efforts at Dadri will ultimately transform the ash into a productive and self sustaining ecosystem, as leaf fall adds additional organic material and the weathering process continues. 6 refs., 6 figs.

Stability of Monolithic Rubble Mound Breakwater Crown Walls Subjected to Impulsive Loading

DEFF Research Database (Denmark)

Nørgaard, Jørgen Harck; Andersen, Lars Vabbersgaard; Andersen, Thomas Lykke

2012-01-01

This paper evaluates the validity of a simple onedimensional dynamic analysis as well as a FEM model to determine the sliding of a rubble mound breakwater crown wall. The evaluation is based on a case example with real wave load time series and displacements measured from two-dimensional physical...... model tests. The outcome is a more reliable evaluation of the applicability of simple dynamic calculations for the estimation of sliding distances of rubble mound superstructures. This is of great practical importance since many existing rubble mound crown walls are subjected to increasing wave loads...

Indigenous utilization of termite mounds and their sustainability in a rice growing village of the central plain of Laos.

Science.gov (United States)

Miyagawa, Shuichi; Koyama, Yusaku; Kokubo, Mika; Matsushita, Yuichi; Adachi, Yoshinao; Sivilay, Sengdeaune; Kawakubo, Nobumitsu; Oba, Shinya

2011-08-18

The objective of this study was to investigate the indigenous utilization of termite mounds and termites in a rain-fed rice growing village in the central plain of Laos, where rice production is low and varies year-to-year, and to assess the possibility of sustainable termite mound utilization in the future. This research was carried out from 2007 to 2009. The termites were collected from their mounds and surrounding areas and identified. Twenty villagers were interviewed on their use of termites and their mounds in the village. Sixty-three mounds were measured to determine their dimensions in early March, early July and middle to late November, 2009. Eleven species of Termitidae were recorded during the survey period. It was found that the villagers use termite mounds as fertilizer for growing rice, vegetable beds and charcoal kilns. The villagers collected termites for food and as feed for breeding fish. Over the survey period, 81% of the mounds surveyed increased in volume; however, the volume was estimated to decrease by 0.114 m3 mound(-1) year(-1) on average due to several mounds being completely cut out. It was concluded that current mound utilization by villagers is not sustainable. To ensure sustainable termite utilization in the future, studies should be conducted to enhance factors that promote mound restoration by termites. Furthermore, it will be necessary to improve mound conservation methods used by the villagers after changes in the soil mass of mounds in paddy fields and forests has been measured accurately. The socio-economic factors that affect mound utilization should also be studied.

Indigenous utilization of termite mounds and their sustainability in a rice growing village of the central plain of Laos

Directory of Open Access Journals (Sweden)

Sivilay Sengdeaune

2011-08-01

Full Text Available Abstract Background The objective of this study was to investigate the indigenous utilization of termite mounds and termites in a rain-fed rice growing village in the central plain of Laos, where rice production is low and varies year-to-year, and to assess the possibility of sustainable termite mound utilization in the future. This research was carried out from 2007 to 2009. Methods The termites were collected from their mounds and surrounding areas and identified. Twenty villagers were interviewed on their use of termites and their mounds in the village. Sixty-three mounds were measured to determine their dimensions in early March, early July and middle to late November, 2009. Results Eleven species of Termitidae were recorded during the survey period. It was found that the villagers use termite mounds as fertilizer for growing rice, vegetable beds and charcoal kilns. The villagers collected termites for food and as feed for breeding fish. Over the survey period, 81% of the mounds surveyed increased in volume; however, the volume was estimated to decrease by 0.114 m3 mound-1 year-1 on average due to several mounds being completely cut out. Conclusion It was concluded that current mound utilization by villagers is not sustainable. To ensure sustainable termite utilization in the future, studies should be conducted to enhance factors that promote mound restoration by termites. Furthermore, it will be necessary to improve mound conservation methods used by the villagers after changes in the soil mass of mounds in paddy fields and forests has been measured accurately. The socio-economic factors that affect mound utilization should also be studied.

The hydrology and preservation condition in the flat topped burial mound Klangshøj at Vennebjerg in Vendsyssel

DEFF Research Database (Denmark)

Breuning-Madsen, Henrik; Henriksen, Peter Steen; Kristensen, Jeppe Ågård

2016-01-01

Klangshøj is a flat-topped burial mound similar to the Royal Jelling mounds, although smaller. The myths tell that a well has existed on top of the mound as at Jelling and a spring had flown at the base of the mound. In order to verify the myths and a similar hydrology in Klangshøj as found...... borings, where undecomposed plant remnants, occasionally greenish, were observed. A 14C-dating showed that the mound was built in the Viking Age. The hydrology in Klangshøj is the same as in the Jelling mounds, with a permeable bioturbation zone covering almost impermeable, distinct sod layers. This form...

Differences between bacterial communities in the gut of a soil-feeding termite (Cubitermes niokoloensis) and its mounds.

Science.gov (United States)

Fall, Saliou; Hamelin, Jérôme; Ndiaye, Farma; Assigbetse, Komi; Aragno, Michel; Chotte, Jean Luc; Brauman, Alain

2007-08-01

In tropical ecosystems, termite mound soils constitute an important soil compartment covering around 10% of African soils. Previous studies have shown (S. Fall, S. Nazaret, J. L. Chotte, and A. Brauman, Microb. Ecol. 28:191-199, 2004) that the bacterial genetic structure of the mounds of soil-feeding termites (Cubitermes niokoloensis) is different from that of their surrounding soil. The aim of this study was to characterize the specificity of bacterial communities within mounds with respect to the digestive and soil origins of the mound. We have compared the bacterial community structures of a termite mound, termite gut sections, and surrounding soil using PCR-denaturing gradient gel electrophoresis (DGGE) analysis and cloning and sequencing of PCR-amplified 16S rRNA gene fragments. DGGE analysis revealed a drastic difference between the genetic structures of the bacterial communities of the termite gut and the mound. Analysis of 266 clones, including 54 from excised bands, revealed a high level of diversity in each biota investigated. The soil-feeding termite mound was dominated by the Actinobacteria phylum, whereas the Firmicutes and Proteobacteria phyla dominate the gut sections of termites and the surrounding soil, respectively. Phylogenetic analyses revealed a distinct clustering of Actinobacteria phylotypes between the mound and the surrounding soil. The Actinobacteria clones of the termite mound were diverse, distributed among 10 distinct families, and like those in the termite gut environment lightly dominated by the Nocardioidaceae family. Our findings confirmed that the soil-feeding termite mound (C. niokoloensis) represents a specific bacterial habitat in the tropics.

Towards the Automatic Detection of Pre-Existing Termite Mounds through UAS and Hyperspectral Imagery.

Science.gov (United States)

Sandino, Juan; Wooler, Adam; Gonzalez, Felipe

2017-09-24

The increased technological developments in Unmanned Aerial Vehicles (UAVs) combined with artificial intelligence and Machine Learning (ML) approaches have opened the possibility of remote sensing of extensive areas of arid lands. In this paper, a novel approach towards the detection of termite mounds with the use of a UAV, hyperspectral imagery, ML and digital image processing is intended. A new pipeline process is proposed to detect termite mounds automatically and to reduce, consequently, detection times. For the classification stage, several ML classification algorithms' outcomes were studied, selecting support vector machines as the best approach for their role in image classification of pre-existing termite mounds. Various test conditions were applied to the proposed algorithm, obtaining an overall accuracy of 68%. Images with satisfactory mound detection proved that the method is "resolution-dependent". These mounds were detected regardless of their rotation and position in the aerial image. However, image distortion reduced the number of detected mounds due to the inclusion of a shape analysis method in the object detection phase, and image resolution is still determinant to obtain accurate results. Hyperspectral imagery demonstrated better capabilities to classify a huge set of materials than implementing traditional segmentation methods on RGB images only.

Ant and termite mound coinhabitants in the wetlands of Santo Antonio da Patrulha, Rio Grande do Sul, Brazil

Directory of Open Access Journals (Sweden)

E. Diehl

Full Text Available This paper reports on ant and termite species inhabiting the mounds (murundus found in three wetland sites in Santo Antonio da Patrulha. Ants and termites were found in 100% of the mounds of two sites and in 20% of those in the third site. Colonies of Camponotus fastigatus were found inhabiting all the mounds, while colonies of Brachymyrmex sp., Linepithema sp., Pheidole sp., and/or Solenopsis sp. were collected in less than 30% of the mounds. In the mounds of the three sites, colonies of Anoplotermes sp. and/or Aparatermes sp. termites were found together with the ant colonies. Another cohabiting termite species, Cortaritermes sp., was found only in the mounds of one site. The results suggest that C. fastigatus is the species building the mounds, with the other species, whether ants or termites, being the inquilines.

Ant and termite mound coinhabitants in the wetlands of Santo Antonio da Patrulha, Rio Grande do Sul, Brazil.

Science.gov (United States)

Diehl, E; Junqueira, L K; Berti-Filho, E

2005-08-01

This paper reports on ant and termite species inhabiting the mounds (murundus) found in three wetland sites in Santo Antonio da Patrulha. Ants and termites were found in 100% of the mounds of two sites and in 20% of those in the third site. Colonies of Camponotus fastigatus were found inhabiting all the mounds, while colonies of Brachymyrmex sp., Linepithema sp., Pheidole sp., and/or Solenopsis sp. were collected in less than 30% of the mounds. In the mounds of the three sites, colonies of Anoplotermes sp. and/or Aparatermes sp. termites were found together with the ant colonies. Another cohabiting termite species, Cortaritermes sp., was found only in the mounds of one site. The results suggest that C. fastigatus is the species building the mounds, with the other species, whether ants or termites, being the inquilines.

Stochastic Design of Rubble Mound Breakwaters

DEFF Research Database (Denmark)

Nielsen, Søren R.K.; Burcharth, Hans F.

The paper presents a level III reliability method from which the armour layer of rubble mound breakwaters can be designed, so that the total costs of construction price and expected maintaince expenses are minimized. Since the physics of the wave-structure interaction are not yet fully understood...

Three-dimensional architecture and development of Danianbryozoan mounds at Limhamn, south-west Sweden, usingground-penetrating radar

DEFF Research Database (Denmark)

Nielsen, Lars; Schack von Brockdorff, A.; Bjerager, Morten Gustav Erik

2009-01-01

in the Limhamn limestone quarry, south-west Sweden, obtained from combined reflected ground-penetrating radar signals and outcrop analysis provide new information about the architecture and growth development of such mounds. The mounds are composed of bryozoan limestone and dark-grey to black flint bands which...... outline mound geometries. Ground-penetrating radar data sections are collected over a 120 m by 60 m grid of data lines with trace spacing of 0·25 m, providing a depth penetration of 7 to 12 m and a vertical resolution of ca 0·30 m. The ground-penetrating radar images outline the geometry of the internal...... layering of the mounds which, typically, have widths and lengths of 30 to 60 m and heights of 5 to 10 m. Mound architecture and growth show great variability in the ground-penetrating radar images. Small-scale mound structures with a palaeorelief of only a few metres may constitute the basis for growth...

Dynamic environments of fungus-farming termite mounds exert growth-modulating effects on fungal crop parasites.

Science.gov (United States)

Katariya, Lakshya; Ramesh, Priya B; Borges, Renee M

2018-03-01

This study investigated for the first time the impact of the internal mound environment of fungus-growing termites on the growth of fungal crop parasites. Mounds of the termite Odontotermes obesus acted as (i) temperature and relative humidity (RH) 'stabilisers' showing dampened daily variation and (ii) 'extreme environments' exhibiting elevated RH and CO 2 levels, compared to the outside. Yet, internal temperatures exhibited seasonal dynamics as did daily and seasonal CO 2 levels. During in situ experiments under termite-excluded conditions within the mound, the growth of the crop parasite Pseudoxylaria was greater inside than outside the mound, i.e., Pseudoxylaria is 'termitariophilic'. Also, ex situ experiments on parasite isolates differing in growth rates and examined under controlled conditions in the absence of termites revealed a variable effect with fungal growth decreasing only under high CO 2 and low temperature conditions, reflecting the in situ parasite growth fluctuations. In essence, the parasite appears to be adapted to survive in the termite mound. Thus the mound microclimate does not inhibit the parasite but the dynamic environmental conditions of the mound affect its growth to varying extents. These results shed light on the impact of animal-engineered structures on parasite ecology, independent of any direct role of animal engineers. © 2017 Society for Applied Microbiology and John Wiley & Sons Ltd.

Do Mound Disturbance and Bait Placement Affect Bait Removal and Treatment Efficacy in Red Imported Fire ant (Hymenoptera: Formicidae at Different Seasons?

Directory of Open Access Journals (Sweden)

Xing P. Hu

2009-01-01

Full Text Available This study provides empirical evidence that disturbing mound immediately before application, as opposed to label recommendation, did not reduce foraging activity of the red imported fire ant, Solenopsis invicta Buren, except for about 10-min delay in foraging. Despite the delayed foraging, there was no significant difference in the amount of baits foraged between disturbed and undisturbed colonies. Eventually, >96% of the baits were foraged, with the maximum removal occurred by 2 and 3 h, respectively, in summer and spring trial. The fastest and great amount of bait removal 1 h post-treatment occurred to baits placed on mound, followed by 0.18–0.3-m from mound base, and the slowest 1.08–1.2-m from mound base. All treatment gave 100% control 1 mo later, regardless of the season, without colony relocation or new colony invasion in the test plots.

Biogeochemical study of termite mounds: a case study from Tummalapalle area of Andhra Pradesh, India.

Science.gov (United States)

Arveti, Nagaraju; Reginald, S; Kumar, K Sunil; Harinath, V; Sreedhar, Y

2012-04-01

Termite mounds are abundant components of Tummalapalle area of uranium mineralization of Cuddapah District of Andhra Pradesh, India. The systematic research has been carried out on the application of termite mound sampling to mineral exploration in this region. The distribution of chemical elements Cu, Pb, Zn, Ni, Co, Cr, Li, Rb, Sr, Ba, and U were studied both in termite soils and adjacent surface soils. Uranium accumulations were noticed in seven termite mounds ranging from 10 to 36 ppm. A biogeochemical parameter called "Biological Absorption Coefficient" of the termite mounds indicated the termite affected soils contained huge amounts of chemical elements than the adjacent soils.

Excavation and aggregation as organizing factors in de novo construction by mound-building termites.

Science.gov (United States)

Green, Ben; Bardunias, Paul; Turner, J Scott; Nagpal, Radhika; Werfel, Justin

2017-06-14

Termites construct complex mounds that are orders of magnitude larger than any individual and fulfil a variety of functional roles. Yet the processes through which these mounds are built, and by which the insects organize their efforts, remain poorly understood. The traditional understanding focuses on stigmergy, a form of indirect communication in which actions that change the environment provide cues that influence future work. Termite construction has long been thought to be organized via a putative 'cement pheromone': a chemical added to deposited soil that stimulates further deposition in the same area, thus creating a positive feedback loop whereby coherent structures are built up. To investigate the detailed mechanisms and behaviours through which termites self-organize the early stages of mound construction, we tracked the motion and behaviour of major workers from two Macrotermes species in experimental arenas. Rather than a construction process focused on accumulation of depositions, as models based on cement pheromone would suggest, our results indicated that the primary organizing mechanisms were based on excavation. Digging activity was focused on a small number of excavation sites, which in turn provided templates for soil deposition. This behaviour was mediated by a mechanism of aggregation, with termites being more likely to join in the work at an excavation site as the number of termites presently working at that site increased. Statistical analyses showed that this aggregation mechanism was a response to active digging, distinct from and unrelated to putative chemical cues that stimulate deposition. Agent-based simulations quantitatively supported the interpretation that the early stage of de novo construction is primarily organized by excavation and aggregation activity rather than by stigmergic deposition. © 2017 The Author(s).

Innovative rubble mound breakwaters for overtopping wave energy conversion

DEFF Research Database (Denmark)

Vicinanza, Diego; Contestabile, Pasquale; Nørgaard, Jørgen Quvang Harck

2014-01-01

to the sea through turbines. Wave loadings and average wave overtopping rate at the rear side of the rubble mound breakwater and in the front reservoir are discussed on the basis of physical 2-D model tests carried out at Aalborg University (DK). The experiments have been analyzed and compared with results...... from model tests and wave load design formulae by Nørgaard et al. (2013) for traditional rubble mound crown walls. The existing prediction methods seem unable to predict the hydraulic performances and loadings on the front reservoir and thus new prediction formulae are proposed based on the new...

Geochemical characteristics and early diagenesis of recent carbonate mound sediments in the Gulf of Cadiz

Science.gov (United States)

Hamaekers, Helen; Foubert, Anneleen; Wienberg, Claudia; Hebbeln, Dierk; Swennen, Rudy

2010-05-01

Cold-water coral carbonate mounds occur in patches along the continental margin of the North Atlantic Ocean, from northern Norway down to Mauretania. Recent research has been focused on carbonate mounds in the Gulf of Cadiz, especially along the Moroccan margin. The Pen Duick, the Renard and the Vernadsky carbonate mound provinces in the Gulf of Cádiz are only some of the mound provinces which have been the subject of several recent research projects (Foubert et al., 2008; Wienberg et al., 2009). No living scleractinians could be found on top of those carbonate mounds. During cruise 64PE284 of RV Pelagia, gravity cores have been taken through carbonate mounds in the Carbonate Mound Provinces (CMP) SE of Yuma mud volcano and N of Meknes mud volcano. These cores have been analysed by several methods such as Magnetic Susceptibility (MS), X-Ray Fluorescence (XRF), Inductive Coupled Plasma Optical Emission Spectroscopy (ICP-OES) and X-Ray Diffraction (XRD) to determine the geochemical characteristics of carbonate mounds, which can be used to quantify the effects of early diagenetic processes which may have altered the palaeo-environmental characteristics of the carbonate mounds. Dating has been done with 14C and U/Th methods pointing to mound growth phases being restricted to glacial periods. XRF and ICP-OES measurements give both qualitative and quantitative data of the chemical composition of the core. The main elements that have been analysed are Ca, Si, Fe, Sr, Al, K, Mg, Ti. According to the trend they follow, they can be devided in two groups, representative for the two encountered fraction types. These two fraction types (biogenic carbonate-rich fraction and terrigenous silicate-rich fraction) can be coupled to interglacial/glacial palaeo-environmental conditions. XRD measurements give an overview of the mineralogical composition of the cores. Thin sections, analysed by cathodeluminescence and classical optical petrography, and micro-CT scans are used to

Termination of the Special Metallurgical (SM) Building at Mound Laboratory: a final report

International Nuclear Information System (INIS)

Harris, W.R.; Kokenge, B.R.; Marsh, G.C.

1976-01-01

The report describes and highlights the more important factors associated with the termination of the Special Metallurgical (SM) Building at Mound Laboratory. As a result, a written record of the more important techniques and procedures is now available for reference by others involved in similar termination efforts. Included in this report is a description of the organizational units that were used in this effort along with a description of their responsibilities. A general description of the SM Building and a discussion of the more relevant procedures and equipment that were used are also presented. In addition, pertinent Health Physics information, such as personnel exposure, final wipe levels in the terminated facility, and assays of the structure, are provided. Based on the experience gained from this project, recommendations were made regarding the design of future radioactive material handling facilities so that when they are ultimately terminated the effort can be accomplished more efficiently

Mound cyclone incinerator. Volume I. Description and performance

International Nuclear Information System (INIS)

Klingler, L.M.

1981-01-01

The Mound cyclone incinerator was developed to fill a need for a simple, relaible incinerator for volume reduction of dry solid waste contaminated with plutonium-238. Although the basic design of the incinerator is for batch burning of solid combustible waste, the incinerator has also been adapted to volume reduction of other waste forms. Specialized waste feeding equipment enables continuous burning of both solid and liquid waste, including full scintillation vials. Modifications to the incinerator offgas system enable burning of waste contaminated with isotopes other than plutonium-238. This document presents the design and performance characteristics of the Mound Cyclone Incinerator for incineration of both solid and liquid waste. Suggestions are included for adaptation of the incinerator to specialized waste materials

Mound Plant Environmental Monitoring Plan

International Nuclear Information System (INIS)

Bauer, L.R.; Tullis, M.S.; Paulick, R.P.; Roush, L.L.

1994-07-01

The purpose of this Environmental Monitoring Plan (EMP) is to describe the environmental monitoring and surveillance programs in place at Mound. The Plan is required by DOE Order 5400.1 (DOE, 1990). The programs described in the EMP are required by the DOE 5400 Order series and by the Environmental Regulatory Guide for Radiological Effluent Monitoring and Environment Surveillance (DOE 1991a), referred to as the Regulatory Guide throughout this Plan

Manipulation/Extraction of Adatom on a Mound: AG(111)

International Nuclear Information System (INIS)

Yildirim, H.

2004-01-01

We present results of an extensive study of the manipulation/extraction of an atom from a small Ag mound on Ag(111) using a Ag tip. Molecular dynamics (MD) and molecular static (MS) simulations were carried out using interaction potentials from the embedded atom method. In order to evaluate the manipulation capabilities of the tip, we first examine in detail the characteristics of the energy landscape in the absence of the tip. We find that the energy barrier for the extraction of the Ag atom, either through lateral (sliding downwards) or through vertical (climbing upwards) diffusion, to be about 0.3 eV. We show that the presence of the tip lowers the energy barrier for both lateral and vertical diffusion. We find that when the tip is above the edge of the mound (at a height of 2.43 A A from the Ag atom) the barrier for diffusion drops to 0.032 eV for lateral and 0.18 eV for vertical manipulation. We discuss the effect of the tip shape and geometry on the energetics, and present a detailed explanation of how the adatom is extracted from a mound in good agreement with experimental observations

Conceptual design report for environmental, safety and health phase III FY-91 line item

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-09-01

The Mound Facility (Mound), located in Miamisburg, Ohio, is a Department of Energy (DOE) development and production facility performing support work for DOE`s weapons and energy-related programs. EG&G Mound Applied Technologies (EG&G) is the Operating Contractor (OC) for this Government-Owned, Contractor-Operated (GOCO) facility. The work performed at Mound emphasizes nuclear energy and explosives technology. Mound is currently implementing an Environmental, Safety, and Health (ES&H) Program designed to protect its employees, the public, and the environment from adverse effects caused by the facility`s activities. Design has been completed, and construction is in progress for Phase I of this multiphase program. Phase II has been submitted for fiscal year (FY) 89 funding and Phase IV is being submitted as an FY 92 line item. This Conceptual Design Report (CDR) addresses Phase III of the ES&H program.

POTENTIAL IMPACT OF BLENDING RESIDUAL SOLIDS FROM TANKS 18/19 MOUNDS WITH TANK 7 OPERATIONS

Energy Technology Data Exchange (ETDEWEB)

Eibling, R; Erich Hansen, E; Bradley Pickenheim, B

2007-03-29

High level waste tanks 18F and 19F have residual mounds of waste which may require removal before the tanks can be closed. Conventional slurry pump technology, previously used for waste removal and tank cleaning, has been incapable of removing theses mounds from tanks 18F and 19F. A mechanical cleaning method has been identified that is potentially capable of removing and transferring the mound material to tank 7F for incorporation in a sludge batch for eventual disposal in high level waste glass by the Defense Waste Processing Facility. The Savannah River National Laboratory has been requested to evaluate whether the material transferred from tanks 18F/19F by the mechanical cleaning technology can later be suspended in Tank 7F by conventional slurry pumps after mixing with high level waste sludge. The proposed mechanical cleaning process for removing the waste mounds from tanks 18 and 19 may utilize a high pressure water jet-eductor that creates a vacuum to mobilize solids. The high pressure jet is also used to transport the suspended solids. The jet-eductor system will be mounted on a mechanical crawler for movement around the bottom of tanks 18 and 19. Based on physical chemical property testing of the jet-eductor system processed IE-95 zeolite and size-reduced IE-95 zeolite, the following conclusions were made: (1) The jet-eductor system processed zeolite has a mean and median particle size (volume basis) of 115.4 and 43.3 microns in water. Preferential settling of these large particles is likely. (2) The jet-eductor system processed zeolite rapidly generates settled solid yield stresses in excess of 11,000 Pascals in caustic supernates and will not be easily retrieved from Tank 7 with the existing slurry pump technology. (3) Settled size-reduced IE-95 zeolite (less than 38 microns) in caustic supernate does not generate yield stresses in excess of 600 Pascals in less than 30 days. (4) Preferential settling of size-reduced zeolite is a function of the amount of

Zonation of Microbial Communities by a Hydrothermal Mound in the Atlantis II Deep (the Red Sea)

KAUST Repository

Wang, Yong

2015-10-20

In deep-sea geothermal rift zones, the dispersal of hydrothermal fluids of moderately-high temperatures typically forms subseafloor mounds. Major mineral components of the crust covering the mound are barite and metal sulfides. As a result of the continental rifting along the Red Sea, metalliferous sediments accumulate on the seafloor of the Atlantis II Deep. In the present study, a barite crust was identified in a sediment core from the Atlantis II Deep, indicating the formation of a hydrothermal mound at the sampling site. Here, we examined how such a dense barite crust could affect the local environment and the distribution of microbial inhabitants. Our results demonstrate distinctive features of mineral components and microbial communities in the sediment layers separated by the barite crust. Within the mound, archaea accounted for 65% of the community. In contrast, the sediments above the barite boundary were overwhelmed by bacteria. The composition of microbial communities under the mound was similar to that in the sediments of the nearby Discovery Deep and marine cold seeps. This work reveals the zonation of microbial communities after the formation of the hydrothermal mound in the subsurface sediments of the rift basin.

Zonation of Microbial Communities by a Hydrothermal Mound in the Atlantis II Deep (the Red Sea.

Directory of Open Access Journals (Sweden)

Yong Wang

Full Text Available In deep-sea geothermal rift zones, the dispersal of hydrothermal fluids of moderately-high temperatures typically forms subseafloor mounds. Major mineral components of the crust covering the mound are barite and metal sulfides. As a result of the continental rifting along the Red Sea, metalliferous sediments accumulate on the seafloor of the Atlantis II Deep. In the present study, a barite crust was identified in a sediment core from the Atlantis II Deep, indicating the formation of a hydrothermal mound at the sampling site. Here, we examined how such a dense barite crust could affect the local environment and the distribution of microbial inhabitants. Our results demonstrate distinctive features of mineral components and microbial communities in the sediment layers separated by the barite crust. Within the mound, archaea accounted for 65% of the community. In contrast, the sediments above the barite boundary were overwhelmed by bacteria. The composition of microbial communities under the mound was similar to that in the sediments of the nearby Discovery Deep and marine cold seeps. This work reveals the zonation of microbial communities after the formation of the hydrothermal mound in the subsurface sediments of the rift basin.

Zonation of Microbial Communities by a Hydrothermal Mound in the Atlantis II Deep (the Red Sea)

KAUST Repository

Wang, Yong; Li, Jiang Tao; He, Li Sheng; Yang, Bo; Gao, Zhao Ming; Cao, Hui Luo; Batang, Zenon B.; Al-Suwailem, Abdulaziz M.; Qian, Pei-Yuan

2015-01-01

In deep-sea geothermal rift zones, the dispersal of hydrothermal fluids of moderately-high temperatures typically forms subseafloor mounds. Major mineral components of the crust covering the mound are barite and metal sulfides. As a result of the continental rifting along the Red Sea, metalliferous sediments accumulate on the seafloor of the Atlantis II Deep. In the present study, a barite crust was identified in a sediment core from the Atlantis II Deep, indicating the formation of a hydrothermal mound at the sampling site. Here, we examined how such a dense barite crust could affect the local environment and the distribution of microbial inhabitants. Our results demonstrate distinctive features of mineral components and microbial communities in the sediment layers separated by the barite crust. Within the mound, archaea accounted for 65% of the community. In contrast, the sediments above the barite boundary were overwhelmed by bacteria. The composition of microbial communities under the mound was similar to that in the sediments of the nearby Discovery Deep and marine cold seeps. This work reveals the zonation of microbial communities after the formation of the hydrothermal mound in the subsurface sediments of the rift basin.

Parallel evolution of mound-building and grass-feeding in Australian nasute termites.

Science.gov (United States)

Arab, Daej A; Namyatova, Anna; Evans, Theodore A; Cameron, Stephen L; Yeates, David K; Ho, Simon Y W; Lo, Nathan

2017-02-01

Termite mounds built by representatives of the family Termitidae are among the most spectacular constructions in the animal kingdom, reaching 6-8 m in height and housing millions of individuals. Although functional aspects of these structures are well studied, their evolutionary origins remain poorly understood. Australian representatives of the termitid subfamily Nasutitermitinae display a wide variety of nesting habits, making them an ideal group for investigating the evolution of mound building. Because they feed on a variety of substrates, they also provide an opportunity to illuminate the evolution of termite diets. Here, we investigate the evolution of termitid mound building and diet, through a comprehensive molecular phylogenetic analysis of Australian Nasutitermitinae. Molecular dating analysis indicates that the subfamily has colonized Australia on three occasions over the past approximately 20 Myr. Ancestral-state reconstruction showed that mound building arose on multiple occasions and from diverse ancestral nesting habits, including arboreal and wood or soil nesting. Grass feeding appears to have evolved from wood feeding via ancestors that fed on both wood and leaf litter. Our results underscore the adaptability of termites to ancient environmental change, and provide novel examples of parallel evolution of extended phenotypes. © 2017 The Author(s).

Pre-Columbian landscape impact and agriculture in the Monumental Mound region of the Llanos de Moxos, lowland Bolivia

Science.gov (United States)

Whitney, Bronwen S.; Dickau, Ruth; Mayle, Francis E.; Soto, J. Daniel; Iriarte, José

2013-09-01

We present a multiproxy study of land use by a pre-Columbian earth mounds culture in the Bolivian Amazon. The Monumental Mounds Region (MMR) is an archaeological sub-region characterized by hundreds of pre-Columbian habitation mounds associated with a complex network of canals and causeways, and situated in the forest-savanna mosaic of the Llanos de Moxos. Pollen, phytolith, and charcoal analyses were performed on a sediment core from a large lake (14 km2), Laguna San José (14°56.97'S, 64°29.70'W). We found evidence of high levels of anthropogenic burning from AD 400 to AD 1280, corroborating dated occupation layers in two nearby excavated habitation mounds. The charcoal decline pre-dates the arrival of Europeans by at least 100 yr, and challenges the notion that the mounds culture declined because of European colonization. We show that the surrounding savanna soils were sufficiently fertile to support crops, and the presence of maize throughout the record shows that the area was continuously cultivated despite land-use change at the end of the earth mounds culture. We suggest that burning was largely confined to the savannas, rather than forests, and that pre-Columbian deforestation was localized to the vicinity of individual habitation mounds, whereas the inter-mound areas remained largely forested.

Estimating total 239240Pu in blow-sand mounds of two safety-shot sites

International Nuclear Information System (INIS)

Gilbert, R.O.; Essington, E.H.

1977-01-01

A study for estimating the total amount (inventory) of 239 240 Pu in blow-sand mounds at two safety-shot sites (Area 13-Project 57 on the Nellis Air Force Base and Clean Slate 3 on the Tonopah Test Range in Nevada) is described. The total amount in blow-sand mounds at these two sites is estimated to be 5.8 +- 1.3 (total +- standard error) and 10.6 +- 2.5 curies, respectively. The total 239 240 Pu in mounds plus desert pavement areas, both to a depth of 5 cm below desert pavement level, is estimated to be 39 +- 5.7 curies at the Project 57 site and 36 +- 4.8 curies at Clean Slate 3. These estimates are compared with the somewhat higher estimates of 46 +- 9 and 37 +- 5.4 curies reported that pertain to only the top 5 cm of mounds and desert pavement. The possibility is discussed that these differences are due to sampling variability arising from the skewed nature of plutonium concentrations, particularly near ground zero

Slumping of brine mounds : bounds on behaviour

NARCIS (Netherlands)

Philips, J.R.; Duijn, van C.J.

1996-01-01

Two modifications of the approximate analysis of interface motion during two-fluid density-driven flows of De Josselin de Jong (Proc. Euromech., 143: 75–82, 1981) are applied to the slumping of finite two-dimensional and axisymmetric brine mounds. Both lead to simple similarity solutions. One

Do Epigeal Termite Mounds Increase the Diversity of Plant Habitats in a Tropical Rain Forest in Peninsular Malaysia?

Science.gov (United States)

Beaudrot, Lydia; Du, Yanjun; Rahman Kassim, Abdul; Rejmánek, Marcel; Harrison, Rhett D.

2011-01-01

The extent to which environmental heterogeneity can account for tree species coexistence in diverse ecosystems, such as tropical rainforests, is hotly debated, although the importance of spatial variability in contributing to species co-existence is well recognized. Termites contribute to the micro-topographical and nutrient spatial heterogeneity of tropical forests. We therefore investigated whether epigeal termite mounds could contribute to the coexistence of plant species within a 50 ha plot at Pasoh Forest Reserve, Malaysia. Overall, stem density was significantly higher on mounds than in their immediate surroundings, but tree species diversity was significantly lower. Canonical correspondence analysis showed that location on or off mounds significantly influenced species distribution when stems were characterized by basal area. Like studies of termite mounds in other ecosystems, our results suggest that epigeal termite mounds provide a specific microhabitat for the enhanced growth and survival of certain species in these species-rich tropical forests. However, the extent to which epigeal termite mounds facilitate species coexistence warrants further investigation. PMID:21625558

Design And Construction Of Mounds For Breakwaters And Coastal Protection

DEFF Research Database (Denmark)

Burcharth, Hans F.; Barends, F.B.J.; Brebner, A.

Design and construction of mound breakwaters has during the last 5 to 10 years entered a new era. The major reason for that is the realization of problems encountered as it became necessary to erect port structures on more exposed shores and in deeper waters. As a consequence of that the P.I.A.N....... they were exposed to. The following sections discuss the stability of mound breakwaters, reasons for failure and design principles. A number of major failures are mentioned specifically. In each case an attempt has been made to explore and explain the reason for the failure....

2014 Strategic Petroleum Reserve Bryan Mound Well Integrity Grading Report.

Energy Technology Data Exchange (ETDEWEB)

Roberts, Barry L; Lord, David; Lord, Anna C. Snider; Bettin, Giorgia; Sobolik, Steven R.; Rudeen, David Keith; Eldredge, Lisa L. (FFPO); Wynn, Karen (FFPO); Checkai, Dean (FFPO); Osborne, Gerad (FFPO); Moore, Darryl (FFPO)

2015-04-01

This report summarizes the work performed in the prioritization of cavern access wells for remediation and monitoring at the Bryan Mound Strategic Petroleum Reserve site. The grading included consideration of all 47 wells at the Bryan Mound site, with each well receiving a separate grade for remediation and monitoring. Numerous factors affecting well integrity were incorporated into the grading including casing survey results, cavern pressure history, results from geomechanical simulations, and site geologic factors. The factors and grading framework used here are the same as those used in developing similar well remediation and monitoring priorities at the Big Hill Strategic Petroleum Reserve Site.

Shrub mound formation and stability on semi-arid slopes in the Northern Negev Desert of Israel: A field and simulation study

NARCIS (Netherlands)

Buis, E.; Temme, A.J.A.M.; Veldkamp, A.; Boeken, B.; Jongmans, A.G.; Breemen, van N.; Schoorl, J.M.

2010-01-01

In semi-arid areas vegetation is scarce and often dominated by individual shrubs on raised mounds. The processes of formation of these mounds are diverse and still debated. Often, shrub mound formation is directly related to the formation of vegetation patterns, thereby assuming that shrub mound

Comparison of two carbonate mound sequences in the Lower Ordovician El Paso Formation, west Texas and southern New Mexico

Energy Technology Data Exchange (ETDEWEB)

Clemons, R.E.

1985-01-01

The El Paso Formations consists of four members, in ascending order: Hitt Canyon, Jose McKelligon and Padre. Mounds in the McKelligon Member exposed in the southern Franklin Mountains were described by Toomey (1970). Most of these mounds are small but one large one is 5.8 m thick and about 13.7 m long in outcrop. The mound rock is chiefly bioclastic wackestone with minor packstone and boundstone. The varied fauna contains echinoderms, sponges and spicules, gastropods, trilobites, digitate algae, Nuia, Girvanella, Pulchrilamina, Calathium, and minor brachiopods and cephalopods. Intraclastic, bioclastic grainstone fills channels cut in the mounds. Similar, but smaller and less spectacular mounds occur in the McKelligon Member in the Florida, Big Hatchet, and Caballo Mountains, Lone Mountain, Cooke's Range, and elsewhere in southwestern New Mexico. A second type of mound is common in the upper part of the Hitt Canyon Member in the Cooke's Range, Red Hills, Caballo and Big Hatchet Mountains. These mounds also are typically small but one in the Red Hills is 13.7 m thick and about 30 m long in outcrop. The mound complex is about 75-80% SH-C and LLH-C stromatolite boundstone and bioclastic wackestone. The remaining 20-25% is bioclastic packstone and grainstone between the SH-C stromatolites and filling channels cut in the mound complex. The limited fauna contains small fragments of echinoderms, gastropods, trilobites, spicules, and Nuia.

Elimination of Coptotermes lacteus (Froggatt) (Blattodea: Rhinotemitidae) Colonies Using Bistrifluron Bait Applied through In-Ground Bait Stations Surrounding Mounds.

Science.gov (United States)

Webb, Garry

2017-09-12

The efficacy of bistrifluron termite bait was evaluated using in-ground bait stations placed around Coptotermes lacteus mounds in south-eastern Australia during late summer and autumn (late February to late May 2012). Four in-ground bait stations containing timber billets were placed around each of twenty mounds. Once sufficient numbers of in-ground stations were infested by termites, mounds were assigned to one of four groups (one, two, three or four 120 g bait canisters or 120 to 480 g bait in total per mound) and bait canisters installed. One mound, nominally assigned treatment with two canisters ultimately had no termite interception in any of the four in-ground stations and not treated. Eighteen of the remaining 19 colonies were eliminated by 12 weeks after bait placement, irrespective of bait quantity removed (range 43 to 480 g). Measures of colony decline-mound repair capability and internal core temperature-did not accurately reflect the colony decline, as untreated colonies showed a similar pattern of decline in both repair capability and internal mound core temperature. However, during the ensuing spring-summer period, capacity to repair the mound was restored in untreated colonies and the internal core temperature profile was similar to the previous spring-summer period which indicated that these untreated colonies remained healthy.

Remediation workers' exposure assessment feasibility study at the Department of Energy's Mound Site: Phase 1

International Nuclear Information System (INIS)

Stevens, G.W.; Back, D.A.

1997-10-01

The Department of Health and Human Services (DHHS), subsequent to the implementation of a Memorandum of Understanding (MOU) between the Departments of Energy (DOE) and Health and Human Services, conducts a program of independent occupational and environmental research studies with funding from DOE. This document on the DOE Mound site represents the second background site document prepared for the development of the NIOSH project entitled: Exposure Assessment of Hazardous Waste (HW), Decontamination (De), Dismantlement (Di), and Clean Up Workers (CW). The purpose of this document is to assemble information relevant to Remediation Workers performing HW, De, Di, and CW task activities at the DOE Mound site addressing four primary objectives. The objectives are: identification of Remediation Workers performing HW, De, Di, and CW task activities anticipated or in progress from the recent past through the next five to 10 years; demographic definition of the workforce performing these activities; identification of the technologies in use or proposed to be used (including considerations regarding health and safety impact upon the workforce); and assembly of summary information for potential chemical, mixed, and radiological contaminant exposure that may be encountered during these processes

Methane fluxes from the mound-building termite species of North Australian savannas

Science.gov (United States)

Jamali, H.; Livesely, S. J.; Arndt, S. K.; Dawes-Gromadzki, T.; Cook, G. D.; Hutley, L.

2009-04-01

Termites are estimated to contribute 3-19% to the global methane emissions. These estimates have large uncertainties because of the limited number of field-based studies and species studied, as well as issues of diel and seasonal variation. We measured methane fluxes from four common mound-building termite species (Microcerotermes nervosus, n=26; M. serratus, n=4; Tumulitermes pastinator, n=5; and Amitermes darwini, n=4) in tropical savannas near Darwin in the Northern Territory, Australia. Methane fluxes from replicated termite mounds were measured in the field using manual chambers with fluxes reported on a mound volume basis. Methane flux was measured in both wet and dry seasons and diel variation was investigated by measuring methane flux every 4 hours over a 24 hour period. Mound temperature was measured concurrently with flux to examine this relationship. In addition, five M. nervosus mounds removed from the field and incubated under controlled temperature conditions over a 24 hour period to remove the effect of varying temperature. During the observation campaigns, mean monthly minimum and maximum temperatures for February (wet season) were 24.7 and 30.8°C, respectively, and were 20.1 to 31.4 °C in June (dry season). Annual rainfall in 2008 for Darwin was 1970.1 mm, with a maximum of 670 mm falling in February and no rain in May and June. Methane fluxes were greatest in the wet season for all species, ranging from 265.1±101.1 (T. pastinator) to 2256.6±757.1 (M. serratus) µg CH4-C/m3/h. In the dry season, methane fluxes were at their lowest, ranging from 10.0±5.5 (T. pastinator) to 338.0±165.9 (M. serratus) µg CH4-C/m3/h. On a diel basis, methane fluxes were smallest at the coolest time of the day (~0700 hrs) and greatest at the warmest (~1400 hrs) for all species, and for both wet and dry seasons. Typical diel variation in flux from M. serratus dominated mounds ranged from 902.6±261.9 to 1392.1±408.1 µg CH4-C/m3/h in wet season and 99.6±57.4 to

Elimination of Coptotermes lacteus (Froggatt (Blattodea: Rhinotemitidae Colonies Using Bistrifluron Bait Applied through In-Ground Bait Stations Surrounding Mounds

Directory of Open Access Journals (Sweden)

Garry Webb

2017-09-01

Full Text Available The efficacy of bistrifluron termite bait was evaluated using in-ground bait stations placed around Coptotermes lacteus mounds in south-eastern Australia during late summer and autumn (late February to late May 2012. Four in-ground bait stations containing timber billets were placed around each of twenty mounds. Once sufficient numbers of in-ground stations were infested by termites, mounds were assigned to one of four groups (one, two, three or four 120 g bait canisters or 120 to 480 g bait in total per mound and bait canisters installed. One mound, nominally assigned treatment with two canisters ultimately had no termite interception in any of the four in-ground stations and not treated. Eighteen of the remaining 19 colonies were eliminated by 12 weeks after bait placement, irrespective of bait quantity removed (range 43 to 480 g. Measures of colony decline—mound repair capability and internal core temperature—did not accurately reflect the colony decline, as untreated colonies showed a similar pattern of decline in both repair capability and internal mound core temperature. However, during the ensuing spring–summer period, capacity to repair the mound was restored in untreated colonies and the internal core temperature profile was similar to the previous spring–summer period which indicated that these untreated colonies remained healthy.

Efficiency of fipronil in the control of the mound-building termite, Nasutitermes sp. (Isoptera: Termitidae) in sugarcane

OpenAIRE

Melo Fo, Reinaldo M.; Veiga, Antônio F.S.L.

1998-01-01

The efficiency of fipronil was evaluated in field conditions at different dosages and two formulations, against Nasutitermes sp. (isopteran: Termitidae) in sugarcane (Sccharum sp.). Termite mounds were indentified, measured and drilled until cellulosic chamber to allow insecticide application. Nine treatments were tested with ten replications in a completely randomized design and each termite mound considered as an experimental unit. after 50 days the termite mounds were opened and the mortal...

A methodology for the analysis of damage progression in rubble mound breakwaters

OpenAIRE

Campos Duque, Álvaro

2016-01-01

Nowadays, risk based designs as well as reliable rehabilitation and maintenance strategies are essential when dealing with coastal structures. In this sense, the probability of failure due to instability of the armour layer is one of the main issues in rubble mound breakwaters, and so is improving the knowledge on its deterioration rate. Both stability and damage progression on rubble mound breakwaters have been studied for more than 80 years, using different approaches, under regular/irregul...

Antarctic Mirabilite Mounds as Mars Analogs: The Lewis Cliffs Ice Tongue Revisited

Science.gov (United States)

Socki, Richard A.; Sun, Tao; Niles, Paul B.; Harvey, Ralph P.; Bish, David L.; Tonui, Eric

2012-01-01

It has been proposed, based on geomorphic and geochemical arguments, that subsurface water has played an important role in the history of water on the planet Mars [1]. Subsurface water, if present, could provide a protected and long lived environment for potential life. Discovery of gullies [2] and recurring slopes [3] on Mars suggest the potential for subsurface liquid water or brines. Recent attention has also focused on small (the mid to high latitudes on the surface of Mars which may be caused by eruptions of subsurface fluids [4, 5]. We have identified massive but highly localized Na-sulfate deposits (mirabilite mounds, Na2SO4 .10H2O) that may be derived from subsurface fluids and may provide insight into the processes associated with subsurface fluids on Mars. The mounds are found on the end moraine of the Lewis Cliffs Ice Tongue (LCIT) [6] in the Transantarctic Mountains, Antarctica, and are potential terrestrial analogs for mounds observed on the martian surface. The following characteristics distinguish LCIT evaporite mounds from other evaporite mounds found in Antarctic coastal environments and/or the McMurdo Dry Valleys: (1) much greater distance from the open ocean (approx.500 km); (2) higher elevation (approx.2200 meters); and (3) colder average annual temperature (average annual temperature = -30 C for LCIT [7] vs. 20 C at sea level in the McMurdo region [8]. Furthermore, the recent detection of subsurface water ice (inferred as debris-covered glacial ice) by the Mars Reconnaissance Orbiter [9] supports the use of an Antarctic glacial environment, particularly with respect to the mirabilite deposits described in this work, as an ideal terrestrial analog for understanding the geochemistry associated with near-surface martian processes. S and O isotopic compositions.

Volume reduction of low-level, combustible, transuranic waste at Mound Facility

International Nuclear Information System (INIS)

Bond, W.H.; Doty, J.W.; Koenst, J.W. Jr.; Luthy, D.F.

Low-level combustible waste (<100 nCi per g of waste) generated during plutonium-238 processing is collected and stored in 55-gallon (200-liter) drums. The composition of this waste is approximately 32 wt % paper, 46% plastic, 16% rubber and cloth, and 6% metal. Treatment of this waste is initiated by burning in the Mound Cyclone Incinerator, which consists of a burning chamber, deluge tank, venturi scrubber and blower. During the two years of operating the Cyclone Incinerator, experiments have been performed on particle distribution throughout the system using various mixtures of feed material. Measurements were taken at the incinerator outlet, after the spray tank, and after the venturi scrubber. An average emission of 0.23 g of particles per kg of feed at the venturi outlet was determined. The distribution of chlorine from the combustion of polyvinyl chloride was studied. Analyses of the off-gas and scrubber solution show that approximately 75 wt % of the chlorine was captured by the scrubber solution and approximately 17 wt % remained in the off-gas after the venturi scrubber. Measurements of the amount of NO/sub chi/ present in the off-gas were also made during the chloride studies. An average of approximately 200 ppM NO/sub chi/ was produced during each incineration run. Immobilization of the incinerator ash is being studied with regard to long-term behavior of the product. The immobilization matrix which looks most promising is ash mixed with Portland 1A cement in a 65/35 wt % ash-to-cement ratio. This matrix exhibits good mechanical properties while maintaining a maximum volume reduction

Implementation of linear bias corrections for calorimeters at Mound

International Nuclear Information System (INIS)

Barnett, T.M.

1993-01-01

In the past, Mound has generally made relative bias corrections as part of the calibration of individual calorimeters. The correction made was the same over the entire operating range of the calorimeter, regardless of the magnitude of the range. Recently, an investigation was performed to check the relevancy of using linear bias corrections to calibrate the calorimeters. The bias is obtained by measuring calibrated plutonium and/or electrical heat standards over the operating range of the calorimeter. The bias correction is then calculated using a simple least squares fit (y = mx + b) of the bias in milliwatts over the operating range of the calorimeter in watts. The equation used is B i = B 0 + (B w * W m ), where B i is the bias at any given power in milliwatts, B 0 is the intercept (absolute bias in milliwatts), B w is the slope (relative bias in milliwatts per watt), and W m is the measured power in watts. The results of the study showed a decrease in the random error of bias corrected data for most of the calorimeters which are operated over a large wattage range (greater than an order of magnitude). The linear technique for bias correction has been fully implemented at Mound and has been included in the Technical Manual, ''A Measurement Control Program for Radiometric Calorimeters at Mound'' (MD-21900)

Modelling effects of tree population dynamics, tree throw and pit-mound formation/diffusion on microtopography over time in different forest settings

Science.gov (United States)

Martin, Y. E.; Johnson, E. A.; Gallaway, J.; Chaikina, O.

2011-12-01

Herein we conduct a followup investigation to an earlier research project in which we developed a numerical model of tree population dynamics, tree throw, and sediment transport associated with the formation of pit-mound features for Hawk Creek watershed, Canadian Rockies (Gallaway et al., 2009). We extend this earlier work by exploring the most appropriate transport relations to simulate the diffusion over time of newly-formed pit-pound features due to tree throw. We combine our earlier model with a landscape development model that can incorporate these diffusive transport relations. Using these combined models, changes in hillslope microtopography over time associated with the formation of pit-mound features and their decay will be investigated. The following ideas have motivated this particular study: (i) Rates of pit-mound degradation remain a source of almost complete speculation, as there is almost no long-term information on process rates. Therefore, we will attempt to tackle the issue of pit-mound degradation in a methodical way that can guide future field studies; (ii) The degree of visible pit-mound topography at any point in time on the landscape is a joint function of the rate of formation of new pit-mound features due to tree death/topple and their magnitude vs. the rate of decay of pit-mound features. An example of one interesting observation that arises is the following: it appears that pit-mound topography is often more pronounced in some eastern North American forests vs. field sites along the eastern slopes of the Canadian Rockies. Why is this the case? Our investigation begins by considering whether pit-mound decay might occur by linear or nonlinear diffusion. What differences might arise depending on which diffusive approach is adopted? What is the magnitude of transport rates associated with these possible forms of transport relations? We explore linear and nonlinear diffusion at varying rates and for different sizes of pit-mound pairs using a

Differences between bacterial communities in the gut of a soil-feeding termite (Cubitermes niokoloensis) and its mounds

OpenAIRE

Fall, Saliou; Hamelin, J.; Ndiaye, Farma; Assigbetse, Komi; Aragno, M.; Chotte, Jean-Luc; Brauman, Alain

2007-01-01

In tropical ecosystems, termite mound soils constitute an important soil compartment covering around 10% of African soils. Previous studies have shown (S. Fall, S. Nazaret, J. L. Chotte, and A. Brauman, Microb. Ecol. 28:191-199, 2004) that the bacterial genetic structure of the mounds of soil-feeding termites (Cubitermes niokoloensis) is different from that of their surrounding soil. The aim of this study was to characterize the specificity of bacterial communities within mounds with respect ...

Diversity And Abundance Of Deep-Water Coral Mounds In The Straits Of Florida: A Result of Adaptability To Local Environments?

Science.gov (United States)

Correa, T. B.; Grasmueck, M.; Eberli, G.; Viggiano, D. A.; Rosenberg, A.; Reed, J. K.

2007-12-01

To improve the understanding of the Florida-Bahamas deep-water coral mound ecosystem, Autonomous Underwater Vehicle (AUV) surveys were conducted on five coral mound fields throughout the Straits of Florida (three sites at the base of slope of Great Bahama Bank (GBB), one in the middle of the Straits (MS) and one at the base of the Miami Terrace (MT)) in water depths of 590 to 860 m. The AUV provides high-resolution bathymetric maps, sub-bottom profiles and oceanographic data. The AUV survey sites were subsequently groundtruthed via sample collection and video transects, using the Johnson Sealink submersible. Contrary to previous surveys, we found a high diversity in coral mound morphology between sites separated by 15 to 80 km. The MT site is characterized by sinusoidal coral mound ridges, while the MS site contains densely clustered small coral mounds. Meanwhile, mounds of the GBB region are better developed, with some individual mounds reaching up to 90 m in height. Benthic coverage of live corals also differs between sites; the GBB sites are characterized by mounds densely covered by large thickets of live corals, while small thickets of mostly dead corals dominate the MT and MS sites. Several environmental factors may explain these differences. For example, bottom current patterns change between sites. The MT and the MS sites have a unidirectional regime (southward or northward flow, respectively), whereas the GBB sites have a tidal current regime. Sedimentation patterns as depicted by sub-bottom profiles also vary between the sites; coral mounds in the GBB area appear to receive higher sediment input, which can significantly enhance mound growth rates as the reef framework baffles and traps mobile sediments. However, coral mounds that cannot keep-up with the sedimentation rate are buried. Therefore, in the high sedimentation areas of GBB, flourishing live coral mounds are limited to elevated positions (i.e. plateaus, ridges crests) where sediment accumulation

Wave Induced Loading and Stability of Rubble Mound Breakwaters

DEFF Research Database (Denmark)

Hald, Tue

conducting model tests very large variability in e.g. the degree of stability is observed. This background motivated the investigations conducted in the present study. The objective was to investigate and clarify which wave parameters are important for the hydraulic stability of the armour layer on typical...... rubble mound breakwaters. Furthermore, it was intended to quantify the influence on the stability of each parameter. Focus was put on the wave induced loading on single armour stones and the relation to the stability. Based on existing literature the state of physical understanding of the processes...... and the stability were investigated. At Aalborg University model tests with an idealized model of a rubble mound breakwater were conducted and formed the basis for a detailed parametric investigation of the wave induced loading. Based on analyses of the experimental data wave-force models were derived containing...

Slope Stability Estimation of the Kościuszko Mound in Cracow

Science.gov (United States)

Wrana, Bogumił; Pietrzak, Natalia

2015-06-01

In the paper, the slope stability problem of the Kościuszko Mound in Cracow, Poland is considered. The slope stability analysis was performed using Plaxis FEM program. The outer surface of the mound has complex geometry. The slope of the cone is not uniform in all directions, on the surface of the cone are pedestrian paths. Due to its complicated geometry it was impossible to do computing by Plaxis input pre-procesor. The initial element mesh was generated using Autodesk Autocad 3D and next it was updated by Plaxis program. The soil parameters were adopted in accordance with the detailed geological soil testing performed in 2012. Calculating model includes geogrids. The upper part was covered by MacMat geogrid, while the lower part of the Mound was reinforced using Terramesh Matt geogrid. The slope analysis was performed by successives reduction of φ /c parameters. The total multiplayer ΣMsf is used to define the value of the soil strength parameters. The article presents the results of slope stability before and after the rainfall during 33 days of precipitation in flood of 2010.

Optimized design for heavy mound venturi

Directory of Open Access Journals (Sweden)

Xing Futang

2017-01-01

Full Text Available The venturi scrubber is one of the most efficient gas cleaning devices for removal of contaminating particles in industrial flue-gas purification processes. The velocity of the gas entering the scrubber is one of the key factors influencing its dust-removal efficiency. In this study, the shapes of the heavy mound and tube wall are optimized, allowing the girth area to become linearly adjustable. The resulting uniformity of velocity distribution is verified numerically.

Spatial patterns and morphology of termite (Macrotermes falciger) mounds in the upper Katanga, D.R. Congo

NARCIS (Netherlands)

Mujinya, B.B.; Adam, M.Y.O.; Mees, F.; Bogaert, J.; Vranken, I.; Erens, H.; Baert, G.; Ngongo, M.; Ranst, van E.

2014-01-01

This study examines the spatial distribution patterns and morphological characteristics of Macrotermes falciger mounds in the peri-urban zone of Lubumbashi, D.R. Congo. Spatial patterns of mounds were assessed using high-resolution satellite images for 24 plots of variable size (3 to 27 ha). Soil

Active use of urban park facilities

DEFF Research Database (Denmark)

Lindberg, Michael; Schipperijn, Jasper

2015-01-01

groups of the facilities. Facilities that provide the opportunity for games and playing activities are more used for PA than facilities directed at individual training of strength and fitness. The opportunity for socializing and playing while being physically active seems important for many users...... was mentioned as a key factor when designing facilities. Our results provide important knowledge to architects, planners and policy makers when aiming at designing activity-promoting facilities in UGS. Future studies need to further investigate the use of facilities among specific target groups, particularly......Abstract Urban green spaces (UGS), and more specific a higher number of facilities in UGS, have been positively associated with physical activity (PA). However, more detailed studies of which facilities generate high levels of PA, for which type of users, are relevant as existing knowledge...

Effects of Erosion from Mounds of Different Termite Genera on Distinct Functional Grassland Types in an African Savannah.

Science.gov (United States)

Gosling, Cleo M; Cromsigt, Joris P G M; Mpanza, Nokukhanya; Olff, Han

A key aspect of savannah vegetation heterogeneity is mosaics formed by two functional grassland types, bunch grasslands, and grazing lawns. We investigated the role of termites, important ecosystem engineers, in creating high-nutrient patches in the form of grazing lawns. Some of the ways termites can contribute to grazing lawn development is through erosion of soil from aboveground mounds to the surrounding soil surface. This may alter the nutrient status of the surrounding soils. We hypothesize that the importance of this erosion varies with termite genera, depending on feeding strategy and mound type. To test this, we simulated erosion by applying mound soil from three termite genera ( Macrotermes , Odontotermes , and Trinervitermes ) in both a field experiment and a greenhouse experiment. In the greenhouse experiment, we found soils with the highest macro nutrient levels (formed by Trinervitermes ) promoted the quality and biomass of both a lawn ( Digitaria longiflora ) and a bunch ( Sporobolus pyramidalis ) grass species. In the field we found that soils with the highest micro nutrient levels (formed by Macrotermes ) showed the largest increase in cover of grazing lawn species. By linking the different nutrient availability of the mounds to the development of different grassland states, we conclude that the presence of termite mounds influences grassland mosaics, but that the type of mound plays a crucial role in determining the nature of the effects.

Measuring damage in physical model tests of rubble mounds

NARCIS (Netherlands)

Hofland, B.; Rosa-Santos, Paulo; Taveira-Pinto, Francisco; Lemos, Rute; Mendonça, A.; Juana Fortes, C

2017-01-01

This paper studies novel ways to evaluate armour damage in physical models of coastal structures. High-resolution damage data for reference rubble mound breakwaters obtained under the HYDRALAB+ joint-research project are analysed and discussed. These tests are used to analyse the way to describe

Origin and Formation of Giant Mounds in Lake Ladoga (Russia) from High-Resolution Seismic Reflection Data

Science.gov (United States)

Gromig, R.; Lebas, E.; Krastel, S.; Averes, T.; Wagner, B.; Melles, M.; Fedorov, G.

2017-12-01

In the framework of the German-Russian project `PLOT - Paleolimnological Transect' (for an overview of the project see Gromig et al., this meeting), a pilot seismic survey was carried out in Lake Ladoga (Russia) in late summer 2013. In total, 1500 km of seismic reflection profiles have been acquired using a mini-GI gun and a 32-channel seismic streamer. The high-resolution of the seismic data allows us to document in detail the sedimentary processes that occurred in the lake during the preglacial and postglacial history. The seismic stratigraphic architecture of the lake shows, from top to bottom, acoustically well-stratified Holocene muds overlaying rather transparent postglacial varves. These sediment successions are usually bordered by a hard reflector underneath, which may represent coarse-grained sediments or a till. The nature of the material composing the uppermost units have been tied to coring information from core Co1309, which was retrieved during the same survey. Of particular interest, are the single to composite, giant (kilometer-scale) mounds directly overlying the hard reflector. Internal architecture of the mounds reveals a complex formation history, with mound types showing significant structural deformation of different degrees; and other mound types showing a central deformation area, which strongly contrasts with the titled reflections or undisturbed stratification visible at the edges. The deepest seismic unit underlying the mounds is characterized by well-bedded, tilted reflectors in the southeastern part of the lake, while clear synclines are identified in the northwestern part of the lake. An erosional truncation separates the deepest unit from the overlying ones. In the work presented here, we focus on the understanding of the origin and the formation of the giant mounds with respect to the glacial history of Lake Ladoga.

Alternative methods for disposal of low-level radioactive wastes. Task 2c: technical requirements for earth mounded concrete bunker disposal of low-level radioactive waste. Volume 4

International Nuclear Information System (INIS)

Miller, W.O.; Bennett, R.D.

1985-10-01

The study reported herein contains the results of Task 2c (Technical Requirements for Earth Mounded Concrete Bunker Disposal of Low-Level Radioactive Waste) of a four-task study entitled ''Criteria for Evaluating Engineered Facilities''. The overall objective of this study is to ensure that the criteria needed to evaluate five alternative low-level radioactive waste (LLW) disposal methods are available to potential license applicants. The earth mounded concrete bunker disposal alternative is one of several methods that may be proposed for disposal of low-level radioactive waste. The name of this alternative is descriptive of the disposal method used in France at the Centre de la Manche. Experience gained with this method at the Centre is described, including unit operations and features and components. Some improvements to the French system are recommended herein, including the use of previous backfill around monoliths and extending the limits of a low permeability surface layer. The applicability of existing criteria developed for near-surface disposal (10 CFR Part 61 Subpart D) to the earth mounded concrete bunker disposal method, as assessed in Task 1, are reassessed herein. With minor qualifications, these criteria were found to be applicable in the reassessment. These conclusions differ slightly from the Task 1 findings

Elimination of field colonies of a mound-building termite Globitermes sulphureus (Isoptera: Termitidae) by bistrifluron bait.

Science.gov (United States)

Neoh, Kok-Boon; Jalaludin, Nur Atiqah; Lee, Chow-Yang

2011-04-01

The efficacy of Xterm, which contains 1% bistrifluron, in the form of cellulose bait pellets was evaluated for its efficacy in eradicating field colonies of the mound-building termite Globitermes sulphureus (Haviland) (Isoptera: Termitidae). The termite mounds were dissected at the end of the experiment to determine whether the colonies were eliminated. By approximately 2 mo postbaiting, the body of termite workers appeared marble white, and mites were present on the body. The soldier-worker ratio increased drastically in the colonies, and the wall surface of the mounds started to erode. Colony elimination required at least a 4-mo baiting period. Mound dissection revealed wet carton materials (food store) that were greatly consumed and overgrown by fast-growing fungi. Decaying cadavers were scattered all over the nests. On average, 84.1 +/- 16.4 g of bait matrix (68.9 +/- 13.4%, an equivalent of 841 +/- 164 mg of bistrifluron) was consumed in each colony. Moreover, we found that a mere 143 mg of bistrifluron was sufficient to eliminate a colony of C. sulphureus.

Lutz's spontaneous sedimentation technique and the paleoparasitological analysis of sambaqui (shell mound sediments

Directory of Open Access Journals (Sweden)

Morgana Camacho

2013-04-01

Full Text Available Parasite findings in sambaquis (shell mounds are scarce. Although the 121 shell mound samples were previously analysed in our laboratory, we only recently obtained the first positive results. In the sambaqui of Guapi, Rio de Janeiro, Brazil, paleoparasitological analysis was performed on sediment samples collected from various archaeological layers, including the superficial layer as a control. Eggs of Acanthocephala, Ascaridoidea and Heterakoidea were found in the archaeological layers. We applied various techniques and concluded that Lutz's spontaneous sedimentation technique is effective for concentrating parasite eggs in sambaqui soil for microscopic analysis.

Lutz's spontaneous sedimentation technique and the paleoparasitological analysis of sambaqui (shell mound) sediments

Science.gov (United States)

Camacho, Morgana; Pessanha, Thaíla; Leles, Daniela; Dutra, Juliana MF; Silva, Rosângela; de Souza, Sheila Mendonça; Araujo, Adauto

2013-01-01

Parasite findings in sambaquis (shell mounds) are scarce. Although the 121 shell mound samples were previously analysed in our laboratory, we only recently obtained the first positive results. In the sambaqui of Guapi, Rio de Janeiro, Brazil, paleoparasitological analysis was performed on sediment samples collected from various archaeological layers, including the superficial layer as a control. Eggs of Acanthocephala, Ascaridoidea and Heterakoidea were found in the archaeological layers. We applied various techniques and concluded that Lutz's spontaneous sedimentation technique is effective for concentrating parasite eggs in sambaqui soil for microscopic analysis. PMID:23579793

Nutritional and Microbial Parameters of Earthworm Cast, Termite Mound and Surrounding Bulk Soil

OpenAIRE

Kawaguchi, Sadao; Nishi, Shingo

2007-01-01

A comparative analysis of nutritional and microbial parameters was conducted on two types of biogenetic structures of earthworm cast (8.7 cm in height, 7 casts/1m×1m) formed by litter eating Pheretima sp., and mound (64 cm in height, 1.0 mounds/10m×50m) built by fungus growing termite, Macrotermes gilvus, and compared to the surrounding bulk soil as control in the tropical monsoon forest in Cu Chi National Park of Viet Nam. The proportion of the sand in the earthworm cast was higher than in t...

Origin of mounds in the Pantanal wetlands: An integrated approach between geomorphology, pedogenesis, ecology and soil micromorphology.

Directory of Open Access Journals (Sweden)

Jairo Calderari de Oliveira Junior

Full Text Available Vegetated mounds are an important geomorphological feature of the Pantanal, where the influence of floods dictates not only hydropedological processes, but also the distribution and ecology of the flora and fauna. This work aimed to identify factors and processes that influence the formation and spatial distribution of the mounds, which are commonly associated with termite activity. In order to characterize pedological processes, macro and micro morphological descriptions, satellite image interpretation, dating of the sandy sedimentary material using OSL and carbon dating using 14C AMS were carried out. This dating of the materials indicates that the sediments in which the soils were formed were deposited during the Pleistocene, while the carbonates are from the Holocene. The basin-like format of the laminar structures suggests that part of the more clayey material was deposited in lacustrine environments. The more humid climate in the Holocene intensified argilluviation, which at an advanced stage, led to a more pronounced textural gradient, reducing drainage and leading to ferrolysis and thickening of the E horizon. Besides pedogenic processes, more erosive flooding during the Holocene began reducing and rounding the landscape's more elevated structures (paleolevees. In the final stage, these structures were occupied by termites to shelter from flooding. Thereafter, the bio-cementation action of the termite nests has increased the resistance of the vegetated mounds to processes of erosion.

Origin of mounds in the Pantanal wetlands: An integrated approach between geomorphology, pedogenesis, ecology and soil micromorphology.

Science.gov (United States)

de Oliveira Junior, Jairo Calderari; Beirigo, Raphael Moreira; Chiapini, Mariane; do Nascimento, Alexandre Ferreira; Couto, Eduardo Guimarães; Vidal-Torrado, Pablo

2017-01-01

Vegetated mounds are an important geomorphological feature of the Pantanal, where the influence of floods dictates not only hydropedological processes, but also the distribution and ecology of the flora and fauna. This work aimed to identify factors and processes that influence the formation and spatial distribution of the mounds, which are commonly associated with termite activity. In order to characterize pedological processes, macro and micro morphological descriptions, satellite image interpretation, dating of the sandy sedimentary material using OSL and carbon dating using 14C AMS were carried out. This dating of the materials indicates that the sediments in which the soils were formed were deposited during the Pleistocene, while the carbonates are from the Holocene. The basin-like format of the laminar structures suggests that part of the more clayey material was deposited in lacustrine environments. The more humid climate in the Holocene intensified argilluviation, which at an advanced stage, led to a more pronounced textural gradient, reducing drainage and leading to ferrolysis and thickening of the E horizon. Besides pedogenic processes, more erosive flooding during the Holocene began reducing and rounding the landscape's more elevated structures (paleolevees). In the final stage, these structures were occupied by termites to shelter from flooding. Thereafter, the bio-cementation action of the termite nests has increased the resistance of the vegetated mounds to processes of erosion.

Giant polygons and mounds in the lowlands of Mars: signatures of an ancient ocean?

Science.gov (United States)

Oehler, Dorothy Z; Allen, Carlton C

2012-06-01

This paper presents the hypothesis that the well-known giant polygons and bright mounds of the martian lowlands may be related to a common process-a process of fluid expulsion that results from burial of fine-grained sediments beneath a body of water. Specifically, we hypothesize that giant polygons and mounds in Chryse and Acidalia Planitiae are analogous to kilometer-scale polygons and mud volcanoes in terrestrial, marine basins and that the co-occurrence of masses of these features in Chryse and Acidalia may be the signature of sedimentary processes in an ancient martian ocean. We base this hypothesis on recent data from both Earth and Mars. On Earth, 3-D seismic data illustrate kilometer-scale polygons that may be analogous to the giant polygons on Mars. The terrestrial polygons form in fine-grained sediments that have been deposited and buried in passive-margin, marine settings. These polygons are thought to result from compaction/dewatering, and they are commonly associated with fluid expulsion features, such as mud volcanoes. On Mars, in Chryse and Acidalia Planitiae, orbital data demonstrate that giant polygons and mounds have overlapping spatial distributions. There, each set of features occurs within a geological setting that is seemingly analogous to that of the terrestrial, kilometer-scale polygons (broad basin of deposition, predicted fine-grained sediments, and lack of significant horizontal stress). Regionally, the martian polygons and mounds both show a correlation to elevation, as if their formation were related to past water levels. Although these observations are based on older data with incomplete coverage, a similar correlation to elevation has been established in one local area studied in detail with newer higher-resolution data. Further mapping with the latest data sets should more clearly elucidate the relationship(s) of the polygons and mounds to elevation over the entire Chryse-Acidalia region and thereby provide more insight into this

Bryan Mound InSAR Analysis U.S. Strategic petroleum Reserve.

Energy Technology Data Exchange (ETDEWEB)

Lord, Anna C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-06-01

The U.S. Strategic Petroleum Reserve (SPR) is a stockpile of emergency crude oil to be tapped into if a disruption in the nation's oil supply occurs. The SPR is comprised of four salt dome sites. Subsidence surveys have been conducted either annually or biennially at all four sites over the life of the program. Monitoring of surface behavior is a first line defense to detecting possible subsurface cavern integrity issues. Over the life of the Bryan Mound site, subsidence rates over abandoned Cavern 3 have continuously been the highest at the site. In an effort to try and understand the subsurface dynamics, specifically over Bryan Mound Cavern 3, historic interferometric synthetic aperture radar (InSAR) data was acquired and processed by TRE Altamira. InSAR involves the processing of multiple satellite synthetic aperture radar scenes acquired across the same location of the Earth's surface at different times to map surface deformation. The analysis of the data has the ability to detect millimeters of motion spanning days, months, year and decades, across specific sites. The intent in regards to the Bryan Mound site was (1) to confirm the higher subsidence rates recorded over abandoned Cavern 3 indicated by land survey and (2) understand the regional surface behavior. This report describes the InSAR analysis results, how those results compare to the historical collection of land survey data, and what additional information the data has provided towards understanding the response recorded at the surface.

Ft-Ir Spectroscopic Analysis of Potsherds Excavated from the First Settlement Layer of Kuriki Mound, Turkey

Science.gov (United States)

Bayazit, Murat; Isik, Iskender; Cereci, Sedat; Issi, Ali; Genc, Elif

The region covering Southeastern Anatolia takes place in upper Mesopotamia, so it has numerous cultural heritages due to its witness to various social movements of different civilizations in ancient times. Kuruki Mound is located on the junction point of Tigris River and Batman Creek, near Oymatas village which is almost 15 km to Batman, Turkey. The mound is dated back to Late Chalcolithic. Archaeological excavations are carried out on two hills named as “Kuriki Mound-1” and “Kuriki Mound-2” in which 4-layer and 2-layer settlements have been revealed, respectively. This region will be left under the water by the reservoir lake of Ilısu Dam when its construction is completed. Thus, characterization of ancient materials such as potsherds, metals and skeleton ruins should be rapidly done. In this study, 12 potsherds excavated from Layer-1 (the first settlement layer after the surface) in Kuriki Mound-2 were investigated by FT-IR spectrometry. Energy dispersive X-ray fluorescence (EDXRF) and X-ray diffraction (XRD) analyses were used as complementary techniques in order to expose chemical and mineralogical/phase contents, respectively. Obtained results showed that the potteries have been produced with calcareous clays and they include moderate amounts of MgO, K2O, Na2O and Fe2O3 in this context. Additionally, high temperature phases have also been detected with XRD analyses in some samples.

Stability of termite mound populations in a variable environment ...

African Journals Online (AJOL)

Of all the climatic variables in the environment of termites in southern Kenya, only rainfall shows marked seasonality and unpredictability. But despite the great variability in rainfall patterns, the populations of termite mounds of various species in three well-separated study areas remained remarkably constant over a period ...

Mathematical Model for Prediction of Flexural Strength of Mound ...

African Journals Online (AJOL)

The mound soil-cement blended proportions were mathematically optimized by using scheffe's approach and the optimization model developed. A computer program predicting the mix proportion for the model was written. The optimal proportion by the program was used prepare beam samples measuring 150mm x 150mm ...

Functional traits of trees on and off termite mounds : Understanding the origin of biotically-driven heterogeneity in savannas

NARCIS (Netherlands)

van der Plas, F.; Howison, R.; Reinders, J.; Fokkema, W.; Olff, H.

Questions In African savannas, Macrotermes termites contribute to small-scale heterogeneity by constructing large mounds. Operating as islands of high nutrient and water availability and low fire frequency, these mounds support distinct, diverse communities of trees that have been shown to be highly

Mapping of Cold-Water Coral Carbonate Mounds Based on Geomorphometric Features: An Object-Based Approach

Directory of Open Access Journals (Sweden)

Markus Diesing

2018-01-01

Full Text Available Cold-water coral reefs are rich, yet fragile ecosystems found in colder oceanic waters. Knowledge of their spatial distribution on continental shelves, slopes, seamounts and ridge systems is vital for marine spatial planning and conservation. Cold-water corals frequently form conspicuous carbonate mounds of varying sizes, which are identifiable from multibeam echosounder bathymetry and derived geomorphometric attributes. However, the often-large number of mounds makes manual interpretation and mapping a tedious process. We present a methodology that combines image segmentation and random forest spatial prediction with the aim to derive maps of carbonate mounds and an associated measure of confidence. We demonstrate our method based on multibeam echosounder data from Iverryggen on the mid-Norwegian shelf. We identified the image-object mean planar curvature as the most important predictor. The presence and absence of carbonate mounds is mapped with high accuracy. Spatially-explicit confidence in the predictions is derived from the predicted probability and whether the predictions are within or outside the modelled range of values and is generally high. We plan to apply the showcased method to other areas of the Norwegian continental shelf and slope where multibeam echosounder data have been collected with the aim to provide crucial information for marine spatial planning.

Beaufort Sea deep-water gas hydrate recovery from a seafloor mound in a region of widespread BSR occurrence

Science.gov (United States)

Hart, Patrick E.; Pohlman, John W.; Lorenson, T.D.; Edwards, Brian D.

2011-01-01

Gas hydrate was recovered from the Alaskan Beaufort Sea slope north of Camden Bay in August 2010 during a U.S. Coast Guard Cutter Healy expedition (USCG cruise ID HLY1002) under the direction of the U.S. Geological Survey (USGS). Interpretation of multichannel seismic (MCS) reflection data collected in 1977 by the USGS across the Beaufort Sea continental margin identified a regional bottom simulating reflection (BSR), indicating that a large segment of the Beaufort Sea slope is underlain by gas hydrate. During HLY1002, gas hydrate was sampled by serendipity with a piston core targeting a steep-sided bathymetric high originally thought to be an outcrop of older, exposed strata. The feature cored is an approximately 1100m diameter, 130 m high conical mound, referred to here as the Canning Seafloor Mound (CSM), which overlies the crest of a buried anticline in a region of sub-parallel compressional folds beneath the eastern Beaufort outer slope. An MCS profile shows a prominent BSR upslope and downslope from the mound. The absence of a BSR beneath the CSM and occurrence of gas hydrate near the summit indicates that free gas has migrated via deep-rooted thrust faults or by structural focusing up the flanks of the anticline to the seafloor. Gas hydrate recovered from near the CSM summit at a subbottom depth of about 5.7 meters in a water depth of 2538 m was of nodular and vein-filling morphology. Although the hydrate was not preserved, residual gas from the core liner contained >95% methane by volume when corrected for atmospheric contamination. The presence of trace C4+hydrocarbons (extrusion contributing to the development of the mound. Blister-like inflation of the seafloor caused by formation and accumulation of shallow hydrate lenses is also a likely factor in CSM growth. Pore water analysis shows the sulfate-methane transition to be very shallow (0-1 mbsf), also supporting an active high-flux interpretation. Pore water with chloride concentrations as low as 160 m

The distribution, abundance, and the effects of fire on mound building termites (Trinervitermes and Cubitermes spp., Isoptera: Termitidae) in northern guinea savanna West Africa.

Science.gov (United States)

Benzie, John A H

1986-11-01

Termite mound densities in typical guinea savanna, Detarium, and grassland (boval) habitats in northern guinea savanna were determined by random quadratting of 2-3 sites in each habitat (100, 10x10 m quadrats per habitat). Dominant species in guinea savanna were T. geminatus (46 mounds ha -1 ) and T. oeconomus (21 mounds ha -1 ), in Detarium T. geminatus (59 mounds ha -1 ) and C. curtatus (45 mounds ha -1 ) and in boval C. curtatus (72 mounds ha -1 ) and T. geminatus (22 mounds ha -1 ). Only C. curtatus densities and total densities differed significantly between sites within habitats, but all species differed significantly in abundance between habitats. The composition of each community was related to general environment but no particular environmental variable was shown to be a major determinant of termite distribution. Evidence for the limitation of termite populations was obtained from indirect evidence of competition between colonies in Detarium, and by experimental manipulation of fire regimes in the typical guinea savanna habitat. Harvester termites increased four-five fold over two years in fire-protected plots as a result of increased food supplies. Total termite densities in the fire-protected community equilibrated to the new population density (100 mounds ha -1 ) after only two-three years.

Role of burrowing activities of the Great Basin pocket mouse (Perognathus parvus) in the dispersal of radionuclides on a decommissioned pond

International Nuclear Information System (INIS)

Landeen, D.S.; Mitchell, R.M.

1982-08-01

The intrusion of waste burial sites by animals is a common occurrence at nuclear waste facilities. This study identifies parameters associated with burrowing activities of the Great Basin Pocket Mouse at the Hanford Site in southeastern Washington. The objectives of the study were to: (1) document and compare burrow depths on a control site and a decommissioned radioactive waste pond and (2) document 137 Cs concentrations in pocket mice and the soil mounds created by their burrowing activities. Pocket mice burrowed deeper in the backfilled burial site (anti x = 72 cm) than they did in the control site (anti x = 38 cm). The small amounts of 137 Cs found in the mice were an order of magnitude below what was present in the mounds. This indicates that the burrowing habits of these mice and subsequent mound construction may be more important in terms of radionuclide dispersal than the small amounts contained within their bodies. The 137 Cs values reported in the mice and mounds are below Rockwell Hanford Operations (Rockwell) surface soil contamination limits. Information received from test plots will be used in formulating appropriate control mechanisms which may be deployed in the future. In the interim, surface stabilization efforts are being conducted on waste sites to control and deter burrowing animals

Cold-water coral mounds on the Pen Duick Escarpment, Gulf of Cadiz: The MiCROSYSTEMS project approach

NARCIS (Netherlands)

Van Rooij, D.; Blamart, D.; De Mol, L.; Mienis, F.; Pirlet, H.; Wehrmann, L. M.; Barbieri, R.; Maignien, L.; Templer, S. P.; de Haas, H.; Hebbeln, D.; Frank, N.; Larmagnat, S.; Stadnitskaia, A.; Stivaletta, N.; van Weering, T.; Zhang, Y.; Hamoumi, N.; Cnudde, V.; Duyck, P.; Henriet, J.-P.; The MiCROSYSTEMS MD 169 Shipboard Party

2011-01-01

Here we present a case study of three cold-water coral mounds in a juvenile growth stage on top of the Pen Duick Escarpment in the Gulf of Cadiz; Alpha, Beta and Gamma mounds. Although cold-water corals are a common feature on the adjacent cliffs, mud volcanoes and open slope, no actual living

Ecosystem engineering creates a direct nutritional link between 600-m deep cold-water coral mounds and surface productivity

NARCIS (Netherlands)

Soetaert, K.; Mohn, C.; Rengstorf, A.; Grehan, A.; Van Oevelen, D.

2016-01-01

Cold-water corals (CWCs) form large mounds on the seafloor that are hotspots of biodiversity in the deep sea, but it remains enigmatic how CWCs can thrive in this food-limited environment. Here, we infer from model simulations that the interaction between tidal currents and CWC-formed mounds induces

Post Earthquack Slope Stability Analysis of Rubble Mound Breakwater

OpenAIRE

Amin Moradi; Amir Mahmoudzadeh; Yahya Rahim Safavi

2017-01-01

Rubble mound breakwaters are structures built mainly of quarried rock. Generally armourstone or artificial concrete armour units are used for the outer armour layer,which should protect the structure againist wave attack. Armour stones and concrete armoure unites in this outer layer are usually placed with care to obtain effective interlocking and consequently better stability .

Phylogeography of an Australian termite, Amitermes laurensis (Isoptera, Termitidae), with special reference to the variety of mound shapes.

Science.gov (United States)

Ozeki, Masato; Isagi, Yuji; Tsubota, Hiromi; Jacklyn, Peter; Bowman, David M J S

2007-01-01

In northern Australia, the debris-feeding termite Amitermes laurensis builds tall, wedge-shaped mounds in the northern part of Cape York Peninsula and Arnhem Land, where their habitats are seasonally flooded, and small dome shaped mounds in the southeastern part of Cape York Peninsula, where their habitats are well-drained. Phylogeographic analyses were conducted in 238 individuals from 30 populations using the mitochondrial cytochrome oxidase II (COII) gene. DNA sequences of 50 haplotypes were used to construct NJ, MP and ML trees. Phylogenetic trees for 16 Amitermes species showed monophyly of A. laurensis and the variation of A. laurensis mounds did not strongly correspond to the intraspecific phylogeny. It was observed that mounds with the same shape were constructed by phylogenetically different groups under similar environmental conditions and different mounds shapes were built by phylogenetically closely related groups under the different environmental conditions. Thus, phylogenetically close groups of A. laurensis, in different habitats, may adapt to environmental conditions by constructing different mound shapes. We also investigated the phylogeographic structure of A. laurensis. The significant positive correlation between genetic and geographic distances indicated isolation by distance, reflecting restricted dispersal ability of alates. Although the overall genetic structure of A. laurensis showed isolation by distance, we also identified two exceptions: (i) secondary contacts of genetically divergent lineages in southern Cape York Peninsula, and (ii) low genetic differences between geographically separated populations of Cape York Peninsula and Arnhem Land. Therefore, the phylogeography of A. laurensis may reflect continuous gene flow restricted to short distances and past changes of gene flow associated with the fluctuation of environmental conditions accompanying the changing sea levels in the Quaternary.

Feasibility of a Mound-designed transportable calorimeter

International Nuclear Information System (INIS)

Duff, M.F.; Fellers, C.L.

1979-01-01

The feasibility of operating a Mound twin resistance bridge calorimeter outside a temperature-controlled water bath was demonstrated. An existing calorimeter was retrofit with two additional jackets through which water was transferred from an external reservoir. Comparison of test results collected before and after the retrofit indicated that the calorimeter performance was not degraded by this modification. Similarly designed calorimeters have potential applications in laboratories where equipment space is limited for inspectors who are required to transport their assay instrumentation

Hydraulic Response of Rubble Mound Breakwaters

DEFF Research Database (Denmark)

Andersen, Thomas Lykke

, which was not actually identifed as a white spot, but still there was room for big improvements. Rear slope stability and wave re ection has been discussed brie y. The conventional rubble mound breakwater has been investigated for many decades. Anyhow, there is still room for improvements in some areas...... experimental test programme with berm breakwaters, has not only resulted in an enormous amount of overtopping data, but also establishment of a design formula to calculate average overtopping discharges. Further, the test programme led to an improved design rule for front side stability of berm breakwaters...

2011 Mound Site Groundwater Plume Rebound Exercise and Follow-Up - 13440

Energy Technology Data Exchange (ETDEWEB)

Hooten, Gwendolyn [Mound Site Manager, U.S. Department of Energy Office of Legacy Management, Harrison, Ohio (United States); Cato, Rebecca; Lupton, Greg [S.M. Stoller Company, contractor to the U.S. Department of Energy Office of Legacy Management (United States)

2013-07-01

The Mound Site facility near Miamisburg, Ohio, opened in 1948 to support early atomic weapons programs. It grew into a research, development, and production facility performing work in support of the U.S. Department of Energy (DOE) weapons and energy programs. The plant was in operation until 1995. During the course of operation, an onsite landfill was created. The landfill was located over a finger of a buried valley aquifer, which is a sole drinking water source for much of the Miami Valley. In the 1980's, volatile organic compounds (VOCs) were discovered in groundwater at the Mound site. The site was placed on the National Priorities List on November 21, 1989. DOE signed a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) Federal Facility Agreement with the U.S. Environmental Protection Agency (EPA) and the Ohio Environmental Protection Agency. The agreement became effective in October 1990. The area that included the landfill was designated Operational Unit 1 (OU-1). In 1995, a Record of Decision was signed that called for the installation and operation of a pump and treatment (P and T) system in order to prevent the VOCs in OU-1 groundwater from being captured by the onsite water production wells. In addition to the P and T system, a soil vapor extraction (SVE) system was installed in 1997 to accelerate removal of VOCs from groundwater in the OU-1 area. The SVE system was successful in removing large amounts of VOCs and continued to operate until 2007, when the amount of VOCs removed became minimal. A rebound study was started in February 2003 to determine how the groundwater system and contaminants would respond to shutting down the P and T system. The rebound test was stopped in February 2004 because predetermined VOC threshold concentrations were exceeded down-gradient of the landfill. The P and T and SVE systems were restarted after the termination of the rebound test. In 2006, the remediation of the Mound site was

Wave Run-up on the Zeebrugge Rubble Mound Breakwater

DEFF Research Database (Denmark)

De Rouck, Julien; de Walle, Bjorn Van; Troch, Peter

2007-01-01

Full-scale wave run-up measurements have been carried out on the Zeebrugge rubble mound breakwater in the frame of the EU-funded OPTICREST project. Wave run-up has been measured by a run-up gauge and by a so-called spiderweb system. The dimensionless wave run-up value Ru2%Hm0 measured in Zeebrugg...

Actinobacteria from Termite Mounds Show Antiviral Activity against Bovine Viral Diarrhea Virus, a Surrogate Model for Hepatitis C Virus

Directory of Open Access Journals (Sweden)

Marina Aiello Padilla

2015-01-01

Full Text Available Extracts from termite-associated bacteria were evaluated for in vitro antiviral activity against bovine viral diarrhea virus (BVDV. Two bacterial strains were identified as active, with percentages of inhibition (IP equal to 98%. Both strains were subjected to functional analysis via the addition of virus and extract at different time points in cell culture; the results showed that they were effective as posttreatments. Moreover, we performed MTT colorimetric assays to identify the CC50, IC50, and SI values of these strains, and strain CDPA27 was considered the most promising. In parallel, the isolates were identified as Streptomyces through 16S rRNA gene sequencing analysis. Specifically, CDPA27 was identified as S. chartreusis. The CDPA27 extract was fractionated on a C18-E SPE cartridge, and the fractions were reevaluated. A 100% methanol fraction was identified to contain the compound(s responsible for antiviral activity, which had an SI of 262.41. GC-MS analysis showed that this activity was likely associated with the compound(s that had a peak retention time of 5 min. Taken together, the results of the present study provide new information for antiviral research using natural sources, demonstrate the antiviral potential of Streptomyces chartreusis compounds isolated from termite mounds against BVDV, and lay the foundation for further studies on the treatment of HCV infection.

Some recent changes in tritium handling and control at Mound Laboratory

International Nuclear Information System (INIS)

Rhinehammer, T.B.

1976-01-01

Significant reductions in tritium effluents and personnel exposures at Mound Laboratory have been made during the past 5 yr. Yearly effluents are less than 3 percent of former levels and personnel exposures have been reduced by a factor of 300. Several recent changes which have contributed to these reductions include lowered tritium levels in gloveboxes, and the efficiency and capacity of Mound's new effluent removal system. Personnel exposures have been reduced dramatically by changing to precious metal catalytic converters or oxidizers for use with the glovebox gas purification system. Unlike some former systems using hot copper or proprietary reactants for oxygen removal, a catalyst provides very effective removal of both oxygen and tritium. Both oxygen and tritium can be monitored and, if necessary, increments of hydrogen in argon can be added until the oxygen level is brought down to the desired value

Litter-forager termite mounds enhance the ectomycorrhizal symbiosis between Acacia holosericea A. Cunn. Ex G. Don and Scleroderma dictyosporum isolates.

Science.gov (United States)

Duponnois, Robin; Assikbetse, Komi; Ramanankierana, Heriniaina; Kisa, Marija; Thioulouse, Jean; Lepage, Michel

2006-05-01

The hypothesis of the present study was that the termite mounds of Macrotermes subhyalinus (MS) (a litter-forager termite) were inhabited by a specific microflora that could enhance with the ectomycorrhizal fungal development. We tested the effect of this feeding group mound material on (i) the ectomycorrhization symbiosis between Acacia holosericea (an Australian Acacia introduced in the sahelian areas) and two ectomycorrhizal fungal isolates of Scleroderma dictyosporum (IR408 and IR412) in greenhouse conditions, (ii) the functional diversity of soil microflora and (iii) the diversity of fluorescent pseudomonads. The results showed that the termite mound amendment significantly increased the ectomycorrhizal expansion. MS mound amendment and ectomycorrhizal inoculation induced strong modifications of the soil functional microbial diversity by promoting the multiplication of carboxylic acid catabolizing microorganisms. The phylogenetic analysis showed that fluorescent pseudomonads mostly belong to the Pseudomonads monteillii species. One of these, P. monteillii isolate KR9, increased the ectomycorrhizal development between S. dictyosporum IR412 and A. holosericea. The occurrence of MS termite mounds could be involved in the expansion of ectomycorrhizal symbiosis and could be implicated in nutrient flow and local diversity.

High-capacity neutron activation analysis facility

International Nuclear Information System (INIS)

Hochel, R.C.

1979-01-01

A high-capacity neutron activation analysis facility, the Reactor Activation Facility, was designed and built and has been in operation for about a year at one of the Savannah River Plant's production reactors. The facility determines uranium and about 19 other trace elements in hydrogeochemical samples collected in the National Uranium Resource Evaluation program. The facility has a demonstrated average analysis rate of over 10,000 samples per month, and a peak rate of over 16,000 samples per month. Uranium is determined by cyclic activation and delayed neutron counting of the U-235 fission products; other elements are determined from gamma-ray spectra recorded in subsequent irradiation, decay, and counting steps. The method relies on the absolute activation technique and is highly automated for round-the-clock unattended operation

Grainstones and cementstone mounds: The Trogkofel summit section (Lower Permian, Carnic Alps, Austria).

Science.gov (United States)

Schaffhauser, M.; Sanders, D.; Krainer, K.

2009-04-01

In the Carnic Alps, Austria, an Artinskian succession 400 m thick of shallow-water bioclastic limestones and of mounds composed of ?Archaeolithophyllum, Archaeolithoporella and abundant fibrous cementstone (after former aragonite) records deposition along a "grainstone-dominated" platform margin. The section was taken along the route through the east-facing cliff of Trogkofel. The Trogkofel Limestone (Artinskian pro parte) is excellently exposed and preserved the most complete along this route, but no section has hitherto been logged. The total thickness of the Trogkofel Limestone probably is about 550 meters; the summit section comprises its upper 400 meters. The section consists mainly of shallow-water bioclastic limestones (grainstones, packstones, rudstones) intercalated with cementstone mounds. Both the bioclastic limestones and the mounds typically are thick-bedded to, more commonly, unbedded. Throughout the section, intervals a few tens of meters in thickness dominated by bioclastic limestones change vertically with intervals dominated by cementstone mounds. Up-section, no clear-cut trend with respect to prevalent facies, mean depositional water depth, and energy index is obvious. Furthermore, no lime-muddy, meter-scale peritidal cycles, and no teepee structures and no pisolite levels were identified; thin intervals of fenestral lime mudstones and/or of cryptmicrobially-laminated limestones are very rare. The bioclastic limestones commonly weather out unstratified, or show subhorizontal stratification or, more rarely, low-angle cross-stratification. In the upper 100 meters of section, grainstones to fine-grained rudstones rich in keystone vugs are prevalent. The cementstone mounds comprise intervals up to a few meters in thickness; the biogenic component is characterized by foliose crusts pertaining to ?Archaeolithophyllum hidensis and Archaeolithoporella, overgrown by Tubiphytes and fenestrate bryozoans. The ?Archaeolithophyllum-Archaeolithoporella crusts

Subsurface Interim Measures/Interim Remedial Action Plan and Decision Document for the 903 Pad, Mound, and East Trenches Areas (Operable Unit No. 2)

International Nuclear Information System (INIS)

1992-01-01

The Department of Energy (DOE) is pursuing an Interim Measure/Interim Remedial Action (IM/IRA) at the 903 Pad, Mound, and East Trenches Areas (Operable Unit No. 2) at the Rocky Flats Plant (RFP). This MIRA is to be conducted to provide information that will aid in the selection and design of final remedial actions at OU2 that will address removal of suspected free-phase volatile organic compound (VOC) contamination. The Plan involves investigating the removal of residual free-phase VOCs by in situ vacuum-enhanced vapor extraction technology at 3 suspected VOC source areas within OU2. VOC-contaminated vapors extracted from the subsurface would be treated by granular activated carbon (GAC) adsorption and discharged. The Plan also includes water table depression, when applicable at the test sites, to investigate the performance of vapor extraction technology in the saturated zone. The Plan provides for treatment of any contaminated ground water recovered during the IM/IRA at existing RFP treatment facilities. The proposed MVIRA Plan is presented in the document entitled ''Proposed Subsurface Interim Measures/Interim Remedial Action Plan/Environmental Assessment and Decision Document, 903 Pad, Mound, and East Trenches Areas, Operable Unit No. 2, '' dated 20 March 1992. Information concerning the proposed Subsurface IM/IRA was presented during a DOE Quarterly Review meeting held on 07 April 1992 and a public meeting held on 07 May 1992, at the Marriott Hotel in Golden, Colorado. The Responsiveness Summary presents DOE's response to all comments received at the public meeting, as well as those mailed to date to DOE during the public comment period

Behavior of plutonium-238 solutions in the soil and hydrology system at Mound Laboratory

International Nuclear Information System (INIS)

Rodgers, D.R.

1976-01-01

Because plutonium is a potentially hazardous material, extensive precautions have been exercised since Pu operations began at Mound Laboratory to carefully maintain strict control of the Pu and to prevent significant amounts from entering the environment. These precautions include elaborate facility and equipment design criteria, scientific expertise, experience, personnel training, management and operational control systems, and environmental monitoring. In spite of these precautions, in early 1974, core samples from area waterways collected and analyzed showed that 238 Pu concentrations in the sediment of certain waterways adjacent to the site were above the baseline levels expected ( 238 Pu deposits presented no immediate hazard to the general population in the area as indicated by the air and water concentrations which were well within accepted Radioactivity Concentration Guides (RCG) for 238 Pu. Data are presented from an investigation of the extent of the contamination, the source of Pu, how it was transported and deposited in waterways, and potential hazards of these deposits to the general public

The nest growth of the neotropical mound-building termite, Cornitermes cumulans: a micromorphological analysis.

Science.gov (United States)

Cosarinsky, Marcela I

2011-01-01

The nests of Cornitermes cumulans K. (Isoptera: Termitidae), a very common termite in South American grasslands, display notable morphological transformations during the development of the colony. Young colonies inhabit small subterranean nests that develop into large, conspicuous, epigean mounds, inhabited by very populous colonies. Those macromorphological transformations are accompanied by micromorphological changes occurring gradually in the nest walls. The micromorphological changes during nest development described in the present study expand on previous macromorphological descriptions by explaining the re-organization of the soil components during nest growth. In subterranean nests, walls are composed of piles of lensshaped aggregates of soil material, each one surrounded by a thin organic coating. As the nest grows, mound walls are constructed by disassembling this first lenticular structure and rearranging the materials in a new fabric, where sand grains are loosely distributed among soil microaggregates of organic matter and clay. This is also a temporary construction, because the walls of large nests are composed of a porous mass of sands densely cemented with organic matter and clay in the mound, and a compact mass of the same components in the floor.

High-capacity neutron activation analysis facility

International Nuclear Information System (INIS)

Hochel, R.C.; Bowman, W.W.; Zeh, C.W.

1980-01-01

A high-capacity neutron activation analysis facility, the Reactor Activation Facility, was designed and built and has been in operation for about a year at one of the Savannah River Plant's production reactors. The facility determines uranium and about 19 other elements in hydrogeochemical samples collected in the National Uranium Resource Evaluation program, which is sponsored and funded by the United States Department of Energy, Grand Junction Office. The facility has a demonstrated average analysis rate of over 10,000 samples per month, and a peak rate of over 16,000 samples per month. Uranium is determined by cyclic activation and delayed neutron counting of the U-235 fission products; other elements are determined from gamma-ray spectra recorded in subsequent irradiation, decay, and counting steps. The method relies on the absolute activation technique and is highly automated for round-the-clock unattended operation

Effects of vertical wall and tetrapod weights on wave overtopping in rubble mound breakwaters under irregular wave conditions

Directory of Open Access Journals (Sweden)

Park Sang Kil

2014-12-01

Full Text Available Rubble mound breakwaters protect the coastal line against severe erosion caused by wave action. This study examined the performance of different sizes and properties (i.e. height of vertical wall and tetrapod size of rubble mound breakwaters on reducing the overtopping discharge. The physical model used in this study was derived based on an actual rubble mound in Busan Yacht Harbor. This research attempts to fill the gap in practical knowledge on the combined effect of the armor roughness and vertical wall on wave overtopping in rubble mound breakwaters. The main governing parameters used in this study were the vertical wall height, variation of the tetrapod weights, initial water level elevation, and the volume of overtopping under constant wave properties. The experimental results showed that the roughness factor differed according to the tetrapod size. Furthermore, the overtopping discharge with no vertical wall was similar to that with relatively short vertical walls ( 1 γv = 1. Therefore, the experimental results highlight the importance of the height of the vertical wall in reducing overtopping discharge. Moreover, a large tetrapod size may allow coastal engineers to choose a shorter vertical wall to save cost, while obtaining better performance.

Effects of vertical wall and tetrapod weights on wave overtopping in rubble mound breakwaters under irregular wave conditions

Directory of Open Access Journals (Sweden)

Sang Kil Park

2014-12-01

Full Text Available Rubble mound breakwaters protect the coastal line against severe erosion caused by wave action. This study examined the performance of different sizes and properties (i.e. height of vertical wall and tetrapod size of rubble mound breakwaters on reducing the overtopping discharge. The physical model used in this study was derived based on an actual rubble mound in Busan Yacht Harbor. This research attempts to fill the gap in practical knowledge on the combined effect of the armor roughness and vertical wall on wave overtopping in rubble mound breakwaters. The main governing parameters used in this study were the vertical wall height, variation of the tetrapod weights, initial water level elevation, and the volume of overtopping under constant wave properties. The experimental results showed that the roughness factor differed according to the tetrapod size. Furthermore, the overtopping discharge with no vertical wall was similar to that with relatively short vertical walls (γν = 1. Therefore, the experimental results highlight the importance of the height of the vertical wall in reducing overtopping discharge. Moreover, a large tetrapod size may allow coastal engineers to choose a shorter vertical wall to save cost, while obtaining better performance.

Mound-ACT*DE*CONSM feasibility study. Phase 2: Final report

International Nuclear Information System (INIS)

1994-12-01

A portion of the abandoned Miami-Erie Canal paralleling the Greater Miami River receives the runoff and storm-water discharge from Mound Laboratory. In 1969, a low-level plutonium leak contaminated sediment as far away as 1.5 mi from the Mound site along the old canal system. An estimated one million cubic feet of sediment requires remediation. The technology being evaluated for the remediation of the low-level plutonium-238 contamination of the sediment involves two processes: washing the sediments with ACT*DE*CON SM solution to dissolve the contaminant, followed by extraction of the solution and processing with the MAG*SEP SM process to concentrate the contaminant and allow reuse of the ACT*DE*CON SM solution. The processes are being optimized for pilot-scale and field demonstration. Phase 2 of the project primarily involved identification at the laboratory scale of the optimal ACT*DE*CON SM formulation, identification of the ion-exchanger and MAG*SEP SM particles, verification of the plutonium mobility in the treated soil, and evaluation of other process parameters according to a series of tasks

Groundwater monitoring plan for the Hanford Site 200 Area Treated Effluent Disposal Facility

International Nuclear Information System (INIS)

DB Barnett

2000-01-01

Seven years of groundwater monitoring at the 200 Area Treated Effluent Disposal Facility (TEDF) have shown that the uppermost aquifer beneath the facility is unaffected by TEDF effluent. Effluent discharges have been well below permitted and expected volumes. Groundwater mounding from TEDF operations predicted by various models has not been observed, and waterlevels in TEDF wells have continued declining with the dissipation of the nearby B Pond System groundwater mound. Analytical results for constituents with enforcement limits indicate that concentrations of all these are below Practical Quantitation Limits, and some have produced no detections. Likewise, other constituents on the permit-required list have produced results that are mostly below sitewide background. Comprehensive geochemical analyses of groundwater from TEDF wells has shown that most constituents are below background levels as calculated by two Hanford Site-wide studies. Additionally, major ion proportions and anomalously low tritium activities suggest that groundwater in the aquifer beneath the TEDF has been sequestered from influences of adjoining portions of the aquifer and any discharge activities. This inference is supported by recent hydrogeologic investigations which indicate an extremely slow rate of groundwater movement beneath the TEDF. Detailed evaluation of TEDF-area hydrogeology and groundwater geochemistry indicate that additional points of compliance for groundwater monitoring would be ineffective for this facility, and would produce ambiguous results. Therefore, the current groundwater monitoring well network is retained for continued monitoring. A quarterly frequency of sampling and analysis is continued for all three TEDF wells. The constituents list is refined to include only those parameters key to discerning subtle changes in groundwater chemistry, those useful in detecting general groundwater quality changes from upgradient sources, or those retained for comparison with end

LBA-ECO ND-04 Termite Mound and Soil Characterization, Amazonas, Brazil: 1999-2001

Data.gov (United States)

National Aeronautics and Space Administration — ABSTRACT: This data set reports the results of a comprehensive study of mound building termites at the Embrapa research station in the Distrito Agropecuario da...

LBA-ECO ND-04 Termite Mound and Soil Characterization, Amazonas, Brazil: 1999-2001

Data.gov (United States)

National Aeronautics and Space Administration — This data set reports the results of a comprehensive study of mound building termites at the Embrapa research station in the Distrito Agropecuario da SUFRAMA,...

Comparison ecological characteristics of mound-building mouse (mus spicilegus in two natural hotbeds of tularemia at North-West coast of the Black sea

Directory of Open Access Journals (Sweden)

І. T. Rusev

2011-03-01

Full Text Available The analysis of ecology-epizootic monitoring of North-West coast of the Black sea carried out in wintering seasons of 2004, 2005 and 2011 testifies the basic role of the Mound-building mouse (Mus spicilegus Petenyi, 1882 as a carrier of Francisella tularensis. Spatial distribution of the Mound-building mouse strongly dependson a biotope, geographical region and weather conditions of a specific season. Mice nests in the storage mounds are located normally at a depth of 20–40 cm under the food storage chamber. Average number of the mice in storage mounds is 3.08 ± 1.54 in the south of investigated region and 3.88 ± 2.63 – in the NE of the region.

Cold-seep-driven carbonate deposits at the Central American forearc: contrasting evolution and timing in escarpment and mound settings

Science.gov (United States)

Liebetrau, V.; Augustin, N.; Kutterolf, S.; Schmidt, M.; Eisenhauer, A.; Garbe-Schönberg, D.; Weinrebe, W.

2014-10-01

Continuous surface cores of cold-seep carbonates were recovered offshore Pacific Nicaragua and Costa Rica from 800 to 1,500-m water depths (Meteor 66/3) in order to decipher their evolution and methane enriched fluid emanation in contrasting geological settings. Cores from the mounds Iguana, Perezoso, Baula V and from the Jaco Scarp escarpment were used for a multi-method approach. For both settings aragonite was revealed as dominant authigenic carbonate phase in vein fillings and matrix cementation, followed by Mg-calcite as second most abundant. This common precipitation process of CaCO3 polymorphs could be ascribed as indirectly driven by chemical changes of the advecting pore water due to anaerobic oxidation of methane. A more direct influence of seep-related microbial activity on the authigenic mineral assemblage in both settings is probably reflected by the observed minor amounts of dolomite and a dolomite-like CaMg carbonate (MgCO3 ~ 42 %). δ13C data of Jaco Scarp samples are significantly lower (-43 to -56 ‰ PDB) than for mound samples (-22 to -36 ‰ PDB), indicating differences in fluid composition and origin. Noteworthy, δ18O values of Scarp samples correlate most closely with the ocean signature at their time of formation. Documenting the archive potential, a high resolution case study of a mound core implies at least 40 changes in fluid supply within a time interval of approximately 14 ky. As most striking difference, the age data indicate a late-stage downward-progressing cementation front for all three mound cap structures (approx. 2-5 cm/ky), but a significantly faster upward carbonate buildup in the bulging sediments on top of the scarp environment (approx. 120 cm/ky). The latter data set leads to the hypothesis of chemoherm carbonate emplacement in accord with reported sedimentation rates until decompression of the advective fluid system, probably caused by the Jaco Scarp landslide and dating this to approximately 13,000 years ago.

On the Origin of the Dragon Image on the Plate from Shilovka Burial Mound

Directory of Open Access Journals (Sweden)

Liphanov Nicolay А.

2017-07-01

Full Text Available The author of the article analyzes an unique image of two opposed dragons engraved on a bone plate discovered in 1992 at barrow No.1 of Shilovka burial mound located on the right bank of the Volga river in Ulyanovsk Oblast (the excavations were conducted by R.S. Bagautdinov. The burial mound is related to the cattle breeding population of late 7th century. The article considers different hypotheses concerning the origin of these dragon images in the artistic traditions of various regions: China (A.V. Komar, D.G. Savinov, B. Totev, Pelevina, Central Asia (V.G. Kotov, V.E. Flyorova, India (N.A. Fonyakova. According to the author, this image has no apparent iconographic parallels in the traditions of these regions. Such analogues are found in the art of the Mediterranean where the ancient images of various mythological creatures exist alongside the image of the sea dragon “ketos” which later became part of the Christian tradition. The appearance of this monster in the images of the first half – middle of the 1st millennium A.D. is practically identical to the dragons from Shilovka burial mound. According to the author, certain impact on the formation of the considered dragon image was made by Iranian art.

Behaviour and Ecological Impacts of Termites: Fecundity Investigations in Mounds

Directory of Open Access Journals (Sweden)

Wako Sutuma Edessa

2015-03-01

Full Text Available A radical study was conducted on the behaviour and ecological impacts of termites in Haru District of Western Oromia, Ethiopia. It was aimed at investigating the natural behaviour, fecundity in mounds, ecological impacts and recommending possible solutions to termite problems. Four mounds in different sites were vertically dug down to display the profile of the queen, soldiers, workers, number of laid eggs, nymphs and colonies of termites. On an average, termite queens of the study site may lay about 25 eggs per minute, 36, 000 eggs per day and 13, 140, 000 eggs annually. The fourth queen was unearthed to study the structure, size, number of ovaries and fecundity. It was examined that the death of a queen does not affect the colony, because four small queens are formed and one of them becomes the queen of queens and replaced the dead queen promptly. Accordingly, termites are found to be one of the most destructive agents of our ecosystems and their management requests careful and biological control methods. As a result, the negative effect of termites outweighs the positive effect of termites so that minimising the population size is important for human beings.

Focused risk assessment: Mound Plant, Miami-Erie Canal Operable Unit 4

International Nuclear Information System (INIS)

Rogers, D.R.; Dunning, D.F.

1994-01-01

In 1969, an underground waste line at Mound Plant ruptured and released plutonium-238 in a dilute nitric acid solution to the surrounding soils. Most of the acid was neutralized by the native soils. The plutonium, which in a neutral solution is tightly sorbed onto clay particles, remained within the spill area. During remediation, a severe storm eroded some of the contaminated soil. Fine grained plutonium-contaminated clay particles were carried away through the natural drainage courses to the remnants of the Miami-Erie Canal adjacent to Mound Plant, and then into the Great Miami River. This focused risk assessment considers exposure pathways relevant to site conditions, including incidental ingestion of contaminated soils, ingestion of drinking water and fish, and inhalation of resuspended soils and sediments. For each potential exposure pathway, a simplified conceptual model and exposure scenarios have been used to develop conservative estimates of potential radiation dose equivalents and health risks. The conservatism of the dose and risk estimates provides a substantive margin of safety in assuring that the public health is protected

Prospects of Coir Fibre as Reinforcement in Termite Mound Clay Bricks

Directory of Open Access Journals (Sweden)

Akinyemi Banjo A.

2016-09-01

Full Text Available The study is to develop an appropriate environmental friendly building material that would be sourced, obtained locally and used for construction of structures at a low cost by using termite mound soil, reinforced with 0%, 1%, 2%, 3%. and 4% coir fibres. Physical and mechanical tests were conducted on the different composition samples after curing. The particle size distribution showed that clay had the largest percentage with a moisture content of 3.53%, specific gravity of 2.0, liquid limit of 30.5% and plastic limit value of 25.4. The compressive strength test showed a decrease with increase in fibre content from 1% upward, modulus of rupture test showed that increase in fibre content leads to a corresponding increase in rupture while the modulus of elasticity test showed that from 3% to 4% fibre content, a decrease in the elasticity occurred. It can be concluded that low fibre inclusion into compressed termite mound brick is feasible if fibre content do not exceed 2% and thus can be used for both load and non-loading bearing structures.

Geoarchaeological research on Bronze Age settlement mounds in the Kolkheti lowlands at the Black Sea coast of Georgia

Science.gov (United States)

Laermanns, Hannes; Heisterkamp, Arne; Kirkitadze, Giorgi; Elashvili, Mikheil; Verheul, Jan; Kelterbaum, Daniel; Helmut, Brückner

2016-04-01

0.0.1 Situated between the Rivers Enguri in the north and Khobistsqali in the south, more than 20 settlement mounds (local name Dikhagudzuba), identified by field survey and remote sensing techniques, give evidence of a densely populated landscape in the coastal lowlands of eastern Georgia during the Bronze Age. While the existing chronology of these mounds is based on ceramic evidence obtained during a previous archaeological research, only limited information is available on their internal architecture and their palaeoenvironmental context, and the chronology of the different layers is as yet lacking. 0.0.2 Within the framework of a geoarchaeological research project, we carried out eleven vibracores on and in direct vicinity of three of the most prominent mounds, situated close to the villages of Orulu and Ergeta. Based on these sediment cores, our study aims at (i) establishing a chronostratigraphical framework for the settlements based on radiocarbon dating; (ii) reconstructing possible phases and gaps of occupation; and (iii) identifying the environmental conditions during the time of their existence. Geochemical and sedimentological analyses were carried out to decipher element contents (XRF), granulometry, and organic contents (LOI, C/N) of sediment samples, supporting the interpretation of the mounds' stratigraphical evolution and related human occupation. The three investigated settlement mounds are similar in dimension and stratigraphy, and different settlement layers could be identified in each of them. The 14C age estimates indicate that their formation occurred during the second half of the 3rd and the first half of the 2nd millennium BC, thus confirming the archaeological interpretation of their Bronze Age origin. Based on the granulometric and geochemical data, palaeoenvironmental conditions in the vicinity of the settlements were dominated by fluvial processes.

Spatial variability of soil electrical conductivity under the mole rats (Spalax microphthalmus digging activity at the different scales

Directory of Open Access Journals (Sweden)

A. V. Zhukov

2012-07-01

Full Text Available The soil mounds emerged owing to the mole rats’ digging activity have been shown to be characterised by less electrical conductivity than surrounded soil. This effect is due to the changes of the mounds bulk’s density and moisture. The effect of the mole rats’ digging activity on the soil electrical conductivity has been found not to be restricted by the geometrical border of the mounds. The mounds are surrounded by 1–1.5 m halo of increased soil electrical conductivity. The halo size is increased with the aging of the mound and with the compacting of their aggregation.

Stable isotope sales: Mound Laboratory customer and shipment summaries, FY-1975

International Nuclear Information System (INIS)

Eck, C.F.

1976-01-01

A listing is given of Mound Laboratory's sales of stable isotopes of noble gases, carbon, oxygen, nitrogen, and sulfur for Fiscal Year 1975. Purchasers are listed alphabetically and are divided into domestic and foreign groups. A cross reference index by location is included for domestic customers. Cross reference listings by isotope purchased are included for all customers

Diagenesis of silica-rich mounded chalk, the Coniacian Arnager Limestone, Denmark

DEFF Research Database (Denmark)

Buus Madsen, Heine; Stemmerik, Lars; Surlyk, Finn

2010-01-01

The Coniacian Arnager Limestone Formation is exposed on the Danish island of Bornholm in the Baltic Sea. It is composed of mound-bedded siliceous chalk, and X-ray diffraction and scanning electron microscopy indicate a content of 30-70% insoluble minerals, including authigenic opal-CT, quartz......, clinoptilolite, feldspars, calcite, dolomite, and barite. Opal-CT and clinoptilolite are the most common and constitute 16-53% and 2-9%, respectively. The content of insoluble minerals varies laterally bothwithinthemounds and inplanar beds, and the opal-CT content varies by up to 10% vertically. Themounds...... precipitation of opal-CT. The opal-CT formed at temperatures around 17°C, the precipitation lowered the silica activity and the Si/Al ratio of the pore water, resulting in precipitation of clinoptilolite, feldspar and smectite. Calcite formed synchronouslywith the latest clinoptilolite.Minoramounts of quartz...

On the Choice of Structure and Layout of Rubble Mound Breakwater Heads

DEFF Research Database (Denmark)

Maciñeira, Enrique; Burcharth, Hans F.

2006-01-01

 The paper discusses the various functional, environmental and structural conditions to consider related to the choice of breakwater head type. Results from hydraulic model tests of rubble mound and caisson head solutions for the new deep water port at Punto Langosteira, La Coruña, Spain, are pre...

The Influence of Slope and Shelf Contour Currents On The Growth Pattern of A Cold-water Coral Mound Population Along The Margins of The Rockall Trough

Science.gov (United States)

Readman, P. W.; O'Reilly, B. M.; Shannon, P. M.; Jacob, A. W. B.

The importance of bottom currents along the shelf and slope regions of northeast At- lantic basin margins in controlling sediment transport patterns and the development of carbonate mound ecosystems is now well recognised. The detailed structure of one such large carbonate mound population has been resolved along the western margin of the Porupine Bank west of Ireland with deep-tow (TOBI) sidescan. The mounds which comprise the population are circular to elliptical in shape, 50 - 850 m across and up to about 200 m high. Large scale sedimentary bedforms at 800 m water depth are inferred from backscatter zonation produced by strong NE-flowing contour currents. Streamlining effects control the shape of the mounds as they become more elliptical as their size increases. The frequency distribution follows a general power law which is determined by the biological growth rate of the mounds and the rate at which they colonise the substrate. At first bottom currents aid mound growth until they become so large that hydraulic drag forces retard their growth. In the recent past (late Pleistocene to present) if the number of mounds colonising the slope has increased exponentially with time while their growth rate slowed in response to fluid form drag forces, the observed population curve can be recovered. A model for evolution of the population predicts that these increased forces slow biological growth and cause a sharp fall-off in the number of mounds, also in agreement with observation. Correlation with late Pleistocene and Holocene climatic change suggests that the population is either very robust and relatively insensitive to major environmental change along the continental slope such as a change in current regime, or that the factors controlling its develop- ment were stable over large time intervals. This project was undertaken on behalf of the Irish Petroleum Infrastructure Programme.

Ecosystem engineering creates a direct nutritional link between 600-m deep cold-water coral mounds and surface productivity

Science.gov (United States)

Soetaert, Karline; Mohn, Christian; Rengstorf, Anna; Grehan, Anthony; van Oevelen, Dick

2016-10-01

Cold-water corals (CWCs) form large mounds on the seafloor that are hotspots of biodiversity in the deep sea, but it remains enigmatic how CWCs can thrive in this food-limited environment. Here, we infer from model simulations that the interaction between tidal currents and CWC-formed mounds induces downwelling events of surface water that brings organic matter to 600-m deep CWCs. This positive feedback between CWC growth on carbonate mounds and enhanced food supply is essential for their sustenance in the deep sea and represents an example of ecosystem engineering of unparalleled magnitude. This ’topographically-enhanced carbon pump’ leaks organic matter that settles at greater depths. The ubiquitous presence of biogenic and geological topographies along ocean margins suggests that carbon sequestration through this pump is of global importance. These results indicate that enhanced stratification and lower surface productivity, both expected consequences of climate change, may negatively impact the energy balance of CWCs.

Landward Distribution of Wave Overtopping for Rubble Mound Breakwaters

DEFF Research Database (Denmark)

Andersen, Thomas Lykke; Burcharth, Hans F.

2006-01-01

Overtopping data from seven model test projects has been analyzed with respect to the landward spatial distribution of the overtopping discharge. In total more than 1000 overtopping tests have been analysed and a formula derived for prediction of the landward distribution of overtopping behind...... rubble mound structures with a super structure. The analysis led to the conclusion that although the overtopping discharge, for identical wave heights, decreases with increasing wave steepness, then the maximum travel distance increases with increasing wave steepness....

Construction, Maintenance and Repair as Elements in Rubble Mound Breakwater Design

DEFF Research Database (Denmark)

Burcharth, Hans F.; Rietveld, C.F.W.

Very often rubble mound breakwater designs seem to be a result only of stability considerations corresponding to design wave conditions. Designers tend to put too little emphasis on practical problems related to construction, maintenance and repair. As is discussed in the paper due consideration...... of these problems Ieeds to a more economical design in terms of lower total costs during the structural lifetime....

Long-term baited lander experiments at a cold-water coral community on Galway Mound (Belgica Mound Province, NE Atlantic)

Science.gov (United States)

Lavaleye, Marc; Duineveld, Gerard; Bergman, Magda; van den Beld, Inge

2017-11-01

A long-term lander employing a baited camera system was developed to study temporal variation in the presence of scavenging fish and invertebrates at a cold-water coral community on Galway Mound (Belgica Mound Province, NE Atlantic). The camera system was tested during two successful long-term deployments for periods of 6 and 12 months respectively. The baited system, consisting of two separate video cameras with infrared lights and a bait dispenser with 24 bait positions, recorded more than 15,500 clips of 17 s, regularly spread over both periods. New bait, consisting of sardines in oil, was offered at regular time intervals, and attracted scavengers over the whole period of deployment, and especially the crab Chaceon affinis did still eat from it till the end of the deployments. However, the attractiveness for some scavengers, i.e. amphipods, diminished quite quickly. In addition to invertebrate scavengers, namely C. affinis, two other crab species, amphipods, a shrimp and a starfish, also 7 species of fish were recorded near the bait, of which Lepidion eques was by far the most common. Though there was no concrete evidence for seasonal patterns, the observations showed substantial temporal variation in the abundance of several species, especially the crabs C. affinis and Bathynectes maravigna and the fish Phycis blennoides. It is concluded that long-term deployments of such a baited camera system can produce novel data. For instance such a system could be employed for monitoring impacts of disturbances on the deep-sea floor (e.g. mining), as we infer that mobile scavengers will be among the first organisms to show a visible reaction to any chemically and physically (noise, vibrations) alteration of the environment similar to a mine canary.

EPA Facility Registry Service (FRS): RCRA_ACTIVE

Data.gov (United States)

U.S. Environmental Protection Agency — This web feature service contains location and facility identification information from EPA's Facility Registry Service (FRS) for the subset of active hazardous...

Struvite for composting of agricultural wastes with termite mound: Utilizing the unutilized.

Science.gov (United States)

Karak, Tanmoy; Sonar, Indira; Nath, Jyoti Rani; Paul, Ranjit Kumar; Das, Sampa; Boruah, Romesh Kumar; Dutta, Amrit Kumar; Das, Kuntal

2015-01-01

Although, compost is the store house of different plant nutrients, there is a concern for low amount of major nutrients especially nitrogen content in prepared compost. The present study deals with preparation of compost by using agricultural wastes with struvite (MgNH4PO4·6H2O) along with termite mound. Among four composting mixtures, 50kg termite mound and 2.5kg struvite with crop residues (stover of ground nut: 361.65kg; soybean: 354.59kg; potato: 357.67kg and mustard: 373.19kg) and cow dung (84.90kg) formed a good quality compost within 70days of composting having nitrogen, phosphorus and potassium as 21.59, 3.98 and 34.6gkg(-1), respectively. Multivariate analysis of variance revealed significant differences among the composts. The four composts formed two (pit 1, pit 2 and pit 3, pit 4) different groups. Two principal components expressed more than 97% of the total variability. Hierarchical cluster analysis resulted two homogeneous groups of composts. Copyright © 2015 Elsevier Ltd. All rights reserved.

Critiques of the seismic hypothesis and the vegetation stabilization hypothesis for the formation of Mima mounds along the western coast of the U.S.

Science.gov (United States)

Gabet, Emmanuel J.; Burnham, Jennifer L. Horwath; Perron, J. Taylor

2016-09-01

A recent paper published in Geomorphology by Gabet et al. (2014) presents the results of a numerical model supporting the hypothesis that burrowing mammals build Mima mounds - small, densely packed hillocks found primarily in the western United States. The model is based on field observations and produces realistic-looking mounds with spatial distributions similar to real moundfields. Alternative explanations have been proposed for these Mima mounds, including formation by seismic shaking and vegetation-controlled erosion and deposition. In this short communication, we present observations from moundfields in the coastal states of the western U.S. that are incompatible with these alternative theories.

Composting of cow dung and crop residues using termite mounds as bulking agent.

Science.gov (United States)

Karak, Tanmoy; Sonar, Indira; Paul, Ranjit K; Das, Sampa; Boruah, R K; Dutta, Amrit K; Das, Dilip K

2014-10-01

The present study reports the suitability of termite mounds as a bulking agent for composting with crop residues and cow dung in pit method. Use of 50 kg termite mound with the crop residues (stover of ground nut: 361.65 kg; soybean: 354.59 kg; potato: 357.67 kg and mustard: 373.19 kg) and cow dung (84.90 kg) formed a good quality compost within 70 days of composting having nitrogen, phosphorus and potassium as 20.19, 3.78 and 32.77 g kg(-1) respectively with a bulk density of 0.85 g cm(-3). Other physico-chemical and germination parameters of the compost were within Indian standard, which had been confirmed by the application of multivariate analysis of variance and multivariate contrast analysis. Principal component analysis was applied in order to gain insight into the characteristic variables. Four composting treatments formed two different groups when hierarchical cluster analysis was applied. Copyright © 2014 Elsevier Ltd. All rights reserved.

Markers of Soil Organic Matter Transformation in Permafrost Peat Mounds of Northeastern Europe

Science.gov (United States)

Pastukhov, A. V.; Knoblauch, C.; Yakovleva, E. V.; Kaverin, D. A.

2018-01-01

For the paleoreconstruction of permafrost peat mounds and the identification of plant communities participating in the formation of peat, the contents of n-alkanes (C20-C33) have been determined, and relative changes in the stable isotope compositions of carbon and nitrogen and the C/N ratio have been analysed. Several indices ( CPI alkanes, P aq, P wax) have been calculated to assess the degree of decomposition of the peats studied and the contributions of different plant species to their formation. It has been found that shortand long-chain n-alkanes are concentrated in high-moor peat, while medium-chain alkanes are typical for transitional peat. Integrated analysis of the studied markers has shown that the botanical and material composition of peat, anaerobic conditions of bog formation, and permafrost play an important role in the preservation of organic carbon in permafrost peat mounds. Alternation of plant associations is the main reason for changes in n-alkane concentrations, C/N ratios, and δ13C values.

Termite mounds as hot spots of nitrous oxide emissions in South-Sudanian savanna of Burkina Faso (West Africa)

Science.gov (United States)

Brümmer, Christian; Papen, Hans; Wassmann, Reiner; Brüggemann, Nicolas

2009-05-01

Despite a considerable knowledge of the significant role of termites in the global methane budget, very little is known about their contribution to the global nitrous oxide (N2O) budget. Release of N2O from termite (Cubitermes fungifaber) mounds was measured at a natural savanna site in the southwest of Burkina Faso from May to September 2006. Termite N2O emissions were around 20 μg N2O-N m-2 h-1 at the end of the dry season, and up to two orders of magnitude higher than N2O emissions from the surrounding termite-free soil after the onset of the rainy season. The average N2O emission rate from termite mounds during the observation period was 204 μg N2O-N m-2 h-1, and termite mounds contributed 3.0% to total N2O emissions from this savanna ecosystem. However, in other tropical terrestrial ecosystems with other termite species and/or higher termite density this share might be significantly higher.

The LAM space active optics facility

Science.gov (United States)

Engel, C.; Ferrari, M.; Hugot, E.; Escolle, C.; Bonnefois, A.; Bernot, M.; Bret-Dibat, T.; Carlavan, M.; Falzon, F.; Fusco, T.; Laubier, D.; Liotard, A.; Michau, V.; Mugnier, L.

2017-11-01

The next generation of large lightweight space telescopes will require the use of active optics systems to enhance the performance and increase the spatial resolution. Since almost 10 years now, LAM, CNES, THALES and ONERA conjugate their experience and efforts for the development of space active optics through the validation of key technological building blocks: correcting devices, metrology components and control strategies. This article presents the work done so far on active correcting mirrors and wave front sensing, as well as all the facilities implemented. The last part of this paper focuses on the merging of the MADRAS and RASCASSE test-set up. This unique combination will provide to the active optics community an automated, flexible and versatile facility able to feed and characterise space active optics components.

Cultural Symbolism behind the Architectural Design of Mounds Park All-Nations Magnet School.

Science.gov (United States)

Pewewardy, Cornell; May, Paul G.

1992-01-01

The architectural design of Mounds Park All-Nations Magnet School (St. Paul, Minnesota) incorporates cultural symbols representing the Native American worldview and Medicine Wheel Circle beliefs, as well as design elements from aboriginal housing styles, and colors and sculptured elements that reinforce the relationship of nature to building. (SV)

Termite activity in relation to natural grassland soil attributes

NARCIS (Netherlands)

Kaschuk, G.; Pires Santos, J.C.; Almeida, J.A.; Sinhorati, D.S.; Berton-Junior, J.F.

2006-01-01

Soil-feeding termites transport soil for mound building, and this process can affect soil characteristics. To verify the influence of soil termite activity on soil characteristics, samples were collected from top, bottom and center of termite mounds, and of the adjacent area, to assess chemical and

The role of fire on soil mounds and surface roughness in the Mojave Desert

Science.gov (United States)

Soulard, Christopher E.; Esque, Todd C.; Bedford, David R.; Bond, Sandra

2013-01-01

A fundamental question in arid land management centers on understanding the long-term effects of fire on desert ecosystems. To assess the effects of fire on surface topography, soil roughness, and vegetation, we used terrestrial (ground-based) LiDAR to quantify the differences between burned and unburned surfaces by creating a series of high-resolution vegetation structure and bare-earth surface models for six sample plots in the Grand Canyon-Parashant National Monument, Arizona. We find that 11 years following prescribed burns, mound volumes, plant heights, and soil-surface roughness were significantly lower on burned relative to unburned plots. Results also suggest a linkage between vegetation and soil mounds, either through accretion or erosion mechanisms such as wind and/or water erosion. The biogeomorphic implications of fire-induced changes are significant. Reduced plant cover and altered soil surfaces from fire likely influence seed residence times, inhibit seed germination and plant establishment, and affect other ecohydrological processes.

High-Resolution Topographic Analyses of Mounds in Southern Acidalia Planitia, Mars: Implications for Possible Mud Volcanism in Submarine and Subaerial Environments

Directory of Open Access Journals (Sweden)

Ryodo Hemmi

2018-04-01

Full Text Available A northern ocean of Mars is still debated and, if it existed, it may have accompanied valley networks and/or outflow channels, which may have led to the emplacement of a large amount of water to the northern lowlands during the Noachian and/or Hesperian times. However, it is unclear how and under what conditions (submarine or subaerial geologic features such as mounds and giant polygons formed in the northern lowlands. The densely-distributed mounds in Chryse and Acidalia Planitia, >1000 km-wide basins of the northern plains, were suggested to be ancient mud volcanoes formed in an aqueous setting, which is controversial (i.e., mud vs. igneous and submarine vs. subaerial. However, these mounds have not been quantitatively well characterized, particularly with respect to their detailed topography. Here we generated forty digital elevation models (DEMs with resolution of up to 1 m/pixel from High Resolution Imaging Science Experiment (HiRISE stereo image pairs, and we accurately measured the morphometric parameters of ~1300 mounds within the southern part of the Acidalia basin. Their heights and diameters resulted in good accordance with those of mud and igneous volcanoes in submarine/subaerial settings on Earth. Maximum depths of their source reservoirs vary from ~30 to ~450 m for a subaqueous setting and from ~110 to ~860 m for a subaerial setting, both of which are consistent with fluid expulsion from the ~100–4500 m-thick flood deposits (Vastitas Borealis Formation, VBF. On the basis of the morphometric values, we estimated rheological properties of materials forming the mounds and found them consistent with a mud flow origin, which does not rule out an igneous origin. The conditions of possible submarine mud or igneous volcanoes may have harbored less hazardous environments for past life on Mars than those on an ocean-free surface.

303-K Storage Facility: Report on FY98 closure activities

International Nuclear Information System (INIS)

Adler, J.G.

1998-01-01

This report summarizes and evaluates the decontamination activities, sampling activities, and sample analysis performed in support of the closure of the 303-K Storage Facility. The evaluation is based on the validated data included in the data validation package (98-EAP-346) for the 303-K Storage Facility. The results of this evaluation will be used for assessing contamination for the purpose of closing the 303-K Storage Facility as described in the 303-K Storage Facility Closure Plan, DOE/RL-90-04. The closure strategy for the 303-K Storage Facility is to decontaminate the interior of the north half of the 303-K Building to remove known or suspected dangerous waste contamination, to sample the interior concrete and exterior soils for the constituents of concern, and then to perform data analysis, with an evaluation to determine if the closure activities and data meet the closure criteria. The closure criteria for the 303-K Storage Facility is that the concentrations of constituents of concern are not present above the cleanup levels. Based on the evaluation of the decontamination activities, sampling activities, and sample data, determination has been made that the soils at the 303-K Storage Facility meet the cleanup performance standards (WMH 1997) and can be clean closed. The evaluation determined that the 303-K Building cannot be clean closed without additional closure activities. An additional evaluation will be needed to determine the specific activities required to clean close the 303-K Storage Facility. The radiological contamination at the 303-K Storage Facility is not addressed by the closure strategy

The relationship between termite mound CH₄/CO₂ emissions and internal concentration ratios are species specific

OpenAIRE

B. Fest; S. K. Arndt; L. B. Hutley; S. J. Livesley; H. Jamali

2012-01-01

We investigated the relative importance of CH4 and CO2 fluxes from soil and termite mounds at four different sites in the tropical savannas of northern Australia near Darwin and assessed different methods to indirectly predict CH4 fluxes based on CO2 fluxes and internal gas concentrations. The annual flux from termite mounds and surrounding soil was dominated by CO2 with large variations among sites. On a carbon dioxide equivalent (CO2-e) basis, annual CH4 flux estimate...

An Alternative Stability Equation For Rock Armoured Rubble Mound Breakwaters

DEFF Research Database (Denmark)

Hald, Tue; Burcharth, H. F.

2000-01-01

Rubble mound breakwaters are by far the most common type of breakwater, the importance of which is clearly reflected in the vast amount of published research. Especially, the hydraulic stability of the main armour layer has been studied in order to obtain reliable design equations. It should...... equations and model test results still exists. When turning toward prototype the situation is even worse. With the objective to reduce some of the variability an alternative approach based on force considerations is presented. The paper will describe a new stability equation for rock armoured slopes derived...

Scour at the round head of a rubble-mound breakwater

DEFF Research Database (Denmark)

Fredsøe, Jørgen; Sumer, B. Mutlu

1997-01-01

This study complements the investigation on scour around the head of a breakwater, reported in the companion paper where the case of vertical-wall breakwater was considered, The present study deals with the case of rubble-mound breakwater. Two key mechanisms with regard to the scour processes......, and the acceleration due to gravity, g, appears to be the main governing parameter regarding the breaker-induced scour. The scour depth increases with increasing values of these parameters. The conventional stone protection is investigated in the study. An empirical formula is developed for the extent...

HYFLUX: Satellite Exploration of Natural Hydrocarbon Seeps and Discovery of a Methane Hydrate Mound at GC600

Science.gov (United States)

Garcia-Pineda, O. G.; MacDonald, I. R.; Shedd, W.; Zimmer, B.

2009-12-01

Analysis of natural hydrocarbon seeps is important to improve our understanding of methane flux from deeper sediments to the water column. In order to quantify natural hydrocarbon seep formations in the Northern Gulf of Mexico, a set of 686 Synthetic Aperture Radar (SAR) images was analyzed using the Texture Classifying Neural Network Algorithm (TCNNA), which processes SAR data to delineate oil slicks. This analysis resulted in a characterization of 396 natural seep sites distributed in the northern GOM. Within these sites, a maximum of 1248 individual vents where identified. Oil reaching the sea-surface is deflected from its source during transit through the water column. This presentation describes a method for estimating locations of active oil vents based on repeated slick detection in SAR. One of the most active seep formations was detected in MMS lease block GC600. A total of 82 SAR scenes (collected by RADARSAT-1 from 1995 to 2007) was processed covering this region. Using TCNNA the area covered by each slick was computed and Oil Slicks Origins (OSO) were selected as single points within detected oil slicks. At this site, oil slick signatures had lengths up to 74 km and up to 27 km^2 of area. Using SAR and TCNNA, four active vents were identified in this seep formation. The geostatistical mean centroid among all detections indicated a location along a ridge-line at ~1200m. Sea truth observations with an ROV, confirmed that the estimated location of vents had a maximum offset of ~30 m from their actual locations on the seafloor. At the largest vent, a 3-m high, 12-m long mound of oil-saturated gas hydrate was observed. The outcrop contained thousands of ice worms and numerous semi-rigid chimneys from where oily bubbles were escaping in a continuous stream. Three additional vents were found along the ridge; these had lower apparent flow, but were also plugged with gas hydrate mounds. These results support use of SAR data for precise delineation of active seep

Safety assessment for facilities and activities. General safety requirements. Pt. 4

International Nuclear Information System (INIS)

2009-01-01

The Safety Fundamentals publication, Fundamental Safety Principles, establishes principles for ensuring the protection of workers, the public and the environment, now and in the future, from harmful effects of ionizing radiation. The objective of this Safety Requirements publication is to establish the generally applicable requirements to be fulfilled in safety assessment for facilities and activities, with special attention paid to defence in depth, quantitative analyses and the application of a graded approach to the ranges of facilities and of activities that are addressed. The publication also addresses the independent verification of the safety assessment that needs to be carried out by the originators and users of the safety assessment. This publication is intended to provide a consistent and coherent basis for safety assessment across all facilities and activities, which will facilitate the transfer of good practices between organizations conducting safety assessments and will assist in enhancing the confidence of all interested parties that an adequate level of safety has been achieved for facilities and activities. The requirements, which are derived from the Fundamental Safety Principles, relate to any human activity that may cause people to be exposed to radiation risks arising from facilities and activities, as follows: Facilities includes: (a) Nuclear power plants; (b) Other reactors (such as research reactors and critical assemblies); (c) Enrichment facilities and fuel fabrication facilities; (d) Conversion facilities used to generate UF 6 ; (e) Storage and reprocessing plants for irradiated fuel; (f) Facilities for radioactive waste management where radioactive waste is treated, conditioned, stored or disposed of; (g) Any other places where radioactive materials are produced, processed, used, handled or stored; (h) Irradiation facilities for medical, industrial, research and other purposes, and any places where radiation generators are installed; (i

Safety Assessment for Facilities and Activities. General Safety Requirements. Pt. 4

International Nuclear Information System (INIS)

2009-01-01

The Safety Fundamentals publication, Fundamental Safety Principles, establishes principles for ensuring the protection of workers, the public and the environment, now and in the future, from harmful effects of ionizing radiation. The objective of this Safety Requirements publication is to establish the generally applicable requirements to be fulfilled in safety assessment for facilities and activities, with special attention paid to defence in depth, quantitative analyses and the application of a graded approach to the ranges of facilities and of activities that are addressed. The publication also addresses the independent verification of the safety assessment that needs to be carried out by the originators and users of the safety assessment. This publication is intended to provide a consistent and coherent basis for safety assessment across all facilities and activities, which will facilitate the transfer of good practices between organizations conducting safety assessments and will assist in enhancing the confidence of all interested parties that an adequate level of safety has been achieved for facilities and activities. The requirements, which are derived from the Fundamental Safety Principles, relate to any human activity that may cause people to be exposed to radiation risks arising from facilities and activities, as follows: Facilities includes: (a) Nuclear power plants; (b) Other reactors (such as research reactors and critical assemblies); (c) Enrichment facilities and fuel fabrication facilities; (d) Conversion facilities used to generate UF6; (e) Storage and reprocessing plants for irradiated fuel; (f) Facilities for radioactive waste management where radioactive waste is treated, conditioned, stored or disposed of; (g) Any other places where radioactive materials are produced, processed, used, handled or stored; (h) Irradiation facilities for medical, industrial, research and other purposes, and any places where radiation generators are installed; (i

Safety Assessment for Facilities and Activities. General Safety Requirements. Pt. 4

International Nuclear Information System (INIS)

2010-01-01

The Safety Fundamentals publication, Fundamental Safety Principles, establishes principles for ensuring the protection of workers, the public and the environment, now and in the future, from harmful effects of ionizing radiation. The objective of this Safety Requirements publication is to establish the generally applicable requirements to be fulfilled in safety assessment for facilities and activities, with special attention paid to defence in depth, quantitative analyses and the application of a graded approach to the ranges of facilities and of activities that are addressed. The publication also addresses the independent verification of the safety assessment that needs to be carried out by the originators and users of the safety assessment. This publication is intended to provide a consistent and coherent basis for safety assessment across all facilities and activities, which will facilitate the transfer of good practices between organizations conducting safety assessments and will assist in enhancing the confidence of all interested parties that an adequate level of safety has been achieved for facilities and activities. The requirements, which are derived from the Fundamental Safety Principles, relate to any human activity that may cause people to be exposed to radiation risks arising from facilities and activities, as follows: Facilities includes: (a) Nuclear power plants; (b) Other reactors (such as research reactors and critical assemblies); (c) Enrichment facilities and fuel fabrication facilities; (d) Conversion facilities used to generate UF6; (e) Storage and reprocessing plants for irradiated fuel; (f) Facilities for radioactive waste management where radioactive waste is treated, conditioned, stored or disposed of; (g) Any other places where radioactive materials are produced, processed, used, handled or stored; (h) Irradiation facilities for medical, industrial, research and other purposes, and any places where radiation generators are installed; (i

Safety Assessment for Facilities and Activities. General Safety Requirements. Pt. 4

International Nuclear Information System (INIS)

2009-01-01

The Safety Fundamentals publication, Fundamental Safety Principles, establishes principles for ensuring the protection of workers, the public and the environment, now and in the future, from harmful effects of ionizing radiation.? read more The objective of this Safety Requirements publication is to establish the generally applicable requirements to be fulfilled in safety assessment for facilities and activities, with special attention paid to defence in depth, quantitative analyses and the application of a graded approach to the ranges of facilities and of activities that are addressed. The publication also addresses the independent verification of the safety assessment that needs to be carried out by the originators and users of the safety assessment. This publication is intended to provide a consistent and coherent basis for safety assessment across all facilities and activities, which will facilitate the transfer of good practices between organizations conducting safety assessments and will assist in enhancing the confidence of all interested parties that an adequate level of safety has been achieved for facilities and activities. The requirements, which are derived from the Fundamental Safety Principles, relate to any human activity that may cause people to be exposed to radiation risks arising from facilities and activities, as follows: Facilities includes: (a) Nuclear power plants; (b) Other reactors (such as research reactors and critical assemblies); (c) Enrichment facilities and fuel fabrication facilities; (d) Conversion facilities used to generate UF6; (e) Storage and reprocessing plants for irradiated fuel; (f) Facilities for radioactive waste management where radioactive waste is treated, conditioned, stored or disposed of; (g) Any other places where radioactive materials are produced, processed, used, handled or stored; (h) Irradiation facilities for medical, industrial, research and other purposes, and any places where radiation generators are

A prototype on-line work procedure system for radioisotope thermoelectric generator production

International Nuclear Information System (INIS)

Kiebel, G.R.

1991-09-01

An on-line system to manage work procedures is being developed to support radioisotope thermoelectric generator (RTG) assembly and testing in a new production facility. This system implements production work procedures as interactive electronic documents executed at the work site with no intermediate printed form. It provides good control of the creation and application of work procedures and provides active assistance to the worker in performing them and in documenting the results. An extensive prototype of this system is being evaluated to ensure that it will have all the necessary features and that it will fit the user's needs and expectations. This effort has involved the Radioisotope Power Systems Facility (RPSF) operations organization and technology transfer between Westinghouse Hanford Company (Westinghouse Hanford) and EG ampersand G Mound Applied Technologies Inc. (Mound) at the US Department of Energy (DOE) Mound Site. 1 ref

Annual environmental monitoring report: calender year 1977

International Nuclear Information System (INIS)

Farmer, B.M.; Carfagno, D.G.

1978-01-01

The local environment surrounding Mound Facility was monitored for tritium and plutonium-238. The results are reported for calendar year 1977. The environmental parameters analyzed included air, water, foodstuffs, soil and silt. The average concentrations of plutonium-238 and tritium were within the applicable stringent standards for radioactive species adopted by the U.S. DOE. Mound Facility drinking water has been brought into compliance with the new EPA standard for tritium in community drinking water systems, and Mound has undertaken a program to achieve compliance for nine private wells adjacent to the Facility site. The program has partially achieved its objective by bringing Mound wells and some of the nine affected private wells in the vicinity of Mound Facility into compliance with the U.S. EPA standard and significantly reducing tritium concentration in the remaining wells. Data concerning nonradioactive species in air and water are also presented and compared to federal, state, and local standards, where applicable

Innovative rubble mound breakwaters for wave energy conversion

International Nuclear Information System (INIS)

Contestabile, Pasquale; Vicinanza, Diego; Iuppa, Claudio; Cavallaro, Luca; Foti, Enrico

2015-01-01

This paper presents a new Wave Energy Converter named Overtopping BReakwater for Energy Conversion (OBREC) which consists of a rubble mound breakwater with a front reservoir designed with the aim of capturing the wave overtopping in order to produce electricity. The energy is extracted via low head turbines, using the difference in water levels between the reservoir and the mean sea water level. The new design should be capable of adding a revenue generation function to a breakwater while adding cost sharing benefits due to integration. The design can be applied to harbour expansions, existing breakwater maintenance or upgrades due to climate change for a relatively low cost, considering the breakwater would be built regardless of the inclusion of a WEC [it

Preparation of substituting seaweed field mounds accompanying site preparation for No.3 plant in Ikata Nuclear Power Station

International Nuclear Information System (INIS)

Ishihara, Hisashi; Oshima, Teruhiko; Fujisaki, Yuichi; Saeki, Taketoshi

1987-01-01

Shikoku Electric Power Co., Inc. is constructing No.3 plant adjacently to No.1 and No.2 plants in operation in Ikata Nuclear Power Station. In the coastal area of Iyo-nada, many seaweed fields are distributed, which are important biologically and for fishery. In the works of site preparation for No.3 plant, a part of the site is created by reclamation of sea area, therefore the natural seaweed fields in the area disappear. From the viewpoint of various circumstances and environment preservation, it was decided to create about 60,000 m 2 of seaweed field mounds on the seabed around the site as the substitute for disappearing natural seaweed fields. The Seaweed Field Study Group composed of the men of learning and experience was organized to obtain the guidance on the possibility of creating artificial seaweed fields, the techniques for creation and the effect on environment accompanying the creation of mounds. The creation works were started in October, 1985, and are in progress smoothly utilizing effectively the stones and rocks cut in the site preparation works. The topographic and geological features, sea conditions, the present state of seaweed fields, the experiment on creating artificial seaweed fields, the design and construction of mounds and others are reported. (Kako, I.)

School playground facilities as a determinant of children's daily activity

DEFF Research Database (Denmark)

Nielsen, Glen; Bugge, Anna; Hermansen, Bianca

2012-01-01

This study investigates the influence of school playground facilities on children's daily physical activity.......This study investigates the influence of school playground facilities on children's daily physical activity....

Interactive effects of soil-dwelling ants, ant mounds and simulated grazing on local plant community composition

NARCIS (Netherlands)

Veen, G.F.; Olff, H.

2011-01-01

Interactions between aboveground vertebrate herbivores and subterranean yellow meadow ants (Lasius flavus) can drive plant community patterns in grassland ecosystems. Here, we study the relative importance of the presence of ants (L. flavus) and ant mounds under different simulated grazing regimes

Partial Safety Factors for Rubble Mound Breakwaters

DEFF Research Database (Denmark)

Sørensen, John Dalsgaard; Burcharth, H. F.; Christiani, E.

1995-01-01

On the basis of the failure modes formulated in the various subtasks calibration of partial safety factors are described in this paper. The partial safety factors can be used to design breakwaters under quite different design conditions, namely probabilities of failure from 0.01 to 0.4, design...... lifetimes from 20 to 100 years and different qualities of wave data. A code of practice where safety is taken into account using partial safety factors is called a level I code. The partial safety factors are calibrated using First Order Reliability Methods (FORM, see Madsen et al. [1]) where...... in section 3. First Order Reliability Methods are described in section 4, and in section 5 it is shown how partial safety factors can be introduced and calibrated. The format of a code for design and analysis of rubble mound breakwaters is discussed in section 6. The mathematical formulation of the limit...

Quality Assurance Project Plan for Facility Effluent Monitoring Plan activities

International Nuclear Information System (INIS)

Frazier, T.P.

1994-01-01

This Quality Assurance Project Plan addresses the quality assurance requirements for the activities associated with the Facility Effluent Monitoring Plans, which are part of the overall Hanford Site Environmental Protection Plan. This plan specifically applies to the sampling and analysis activities and continuous monitoring performed for all Facility Effluent Monitoring Plan activities conducted by Westinghouse Hanford Company. It is generic in approach and will be implemented in conjunction with the specific requirements of the individual Facility Effluent Monitoring Plans

Mound Facility activities in chemical and physical research: July--December 1977

International Nuclear Information System (INIS)

1978-01-01

Isotope separation of Ar, C, 3 He, Kr, Ne, O, and Xe isotopes is reported. TiFeH/sub x/, TiCoH/sub x/, TiCuH/sub x/, and VH/sub x/ were studied using NMR (proton relaxation times). VD/sub x/ and VT/sub x/ were synthesized. The problem of calculating the valence state of Pu is discussed. A series solution to the plutonium (N,H) characteristic equation is suggested. Shipments of 231 Pa, 230 Th, and 229 Th are reported. Separation and processing of 234 U are also reported. Theoretical methods were developed to calculate temperature distributions as functions of water flow rate in liquid thermal diffusion columns. Diffusion coefficients were measured from 300 to 1200 0 K for Kr-Xe and Kr-Ar. New thermal diffusion factors are submitted for Ne-Ar

Mound Facility activities in chemical and physical research: July-December 1979

International Nuclear Information System (INIS)

1980-01-01

Research is reported in the following fields: isotope separation (Ar, C, He, Kr, Ne, O, Xe), low-temperature research (H intermolecular potential functions, gas analysis in trennschaukel), separation chemistry ( 229 Th, 231 Pa, 230 Th, 234 U), separation research (liquid thermal diffusion, Ca isotope separation, molecular beam scattering, mutual diffusion of noble gas mixtures, lithium chemical exchange with cryptands), and calculations in plutonium chemistry (algorithms, valence in natural water)

Perceptions of Important Characteristics of Physical Activity Facilities: Implications for Engagement in Walking, Moderate and Vigorous Physical Activity.

Science.gov (United States)

Heinrich, Katie M; Haddock, Christopher K; Jitnarin, Natinee; Hughey, Joseph; Berkel, LaVerne A; Poston, Walker S C

2017-01-01

Although few United States adults meet physical activity recommendations, those that do are more likely to access to physical activity facilities. Additionally, vigorous exercisers may be more likely to utilize a nearby physical activity facility, while light-to-moderate exercisers are less likely to do so. However, it is unclear what characteristics of those facilities are most important as well as how those characteristics are related to activity intensity. This study examined relationships between self-reported leisure-time physical activities and the use of and perceived characteristics of physical activity facilities. Data were from a cross-sectional study in a major metropolitan area. Participants ( N  = 582; ages 18-74, mean age = 45 ± 14.7 years) were more likely to be female (69.9%), Caucasian (65.6%), married (51.7%), and have some college education (72.8%). Household surveys queried leisure-time physical activity, regular physical activity facility use, and importance ratings for key facility characteristics. Leisure-time physical activity recommendations were met by 41.0% of participants and 50.9% regularly used a physical activity facility. Regular facility use was positively associated with meeting walking ( p  = 0.036), moderate ( p  importance on facility quality ( p  = 0.022), variety of physical activity options offered ( p  = 0.003), and availability of special equipment and resources ( p  = 0.01). The facility characteristics of low or free cost ( p  = 0.02) and offering childcare ( p  = 0.028) were barriers for walking, and being where friends and family like to go were barriers for moderate leisure-time physical activity ( p  = 0.013). Findings offer insights for structuring interventions using the social ecological model as well as for improving existing physical activity facilities.

Quality Assurance Project Plan for Facility Effluent Monitoring Plan activities

International Nuclear Information System (INIS)

Nickels, J.M.

1991-06-01

This Quality Assurance Project Plan addresses the quality assurance requirements for the Facility Monitoring Plans of the overall site-wide environmental monitoring plan. This plan specifically applies to the sampling and analysis activities and continuous monitoring performed for all Facility Effluent Monitoring Plan activities conducted by Westinghouse Hanford Company. It is generic in approach and will be implemented in conjunction with the specific requirements of individual Facility Effluent Monitoring Plans. This document is intended to be a basic road map to the Facility Effluent Monitoring Plan documents (i.e., the guidance document for preparing Facility Effluent Monitoring Plans, Facility Effluent Monitoring Plan determinations, management plan, and Facility Effluent Monitoring Plans). The implementing procedures, plans, and instructions are appropriate for the control of effluent monitoring plans requiring compliance with US Department of Energy, US Environmental Protection Agency, state, and local requirements. This Quality Assurance Project Plan contains a matrix of organizational responsibilities, procedural resources from facility or site manuals used in the Facility Effluent Monitoring Plans, and a list of the analytes of interest and analytical methods for each facility preparing a Facility Effluent Monitoring Plan. 44 refs., 1 figs., 2 tabs

Dig-face monitoring during excavation of a radioactive plume at Mound Laboratory, Ohio

International Nuclear Information System (INIS)

Josten, N.E.; Gehrke, R.J.; Carpenter, M.V.

1995-12-01

A dig-face monitoring system consists of onsite hardware for collecting information on changing chemical, radiological, and physical conditions in the subsurface soil during the hazardous site excavation. A prototype dig-face system was take to Mount Laboratory for a first trial. Mound Area 7 was the site of historical disposals of 232 Th, 227 Ac, and assorted debris. The system was used to monitor a deep excavation aimed at removing 227 Ac-contaminated soils. Radiological, geophysical, and topographic sensors were used to scan across the excavation dig-face at four successive depths as soil was removed. A 3-D image of the contamination plumes was developed; the radiation sensor data indicated that only a small portion of the excavated soil volume was contaminated. The spatial information produced by the dig-face system was used to direct the excavation activities into the area containing the 227 Ac and to evaluate options for handling the separate 232 Th plume

Perceptions of Important Characteristics of Physical Activity Facilities: Implications for Engagement in Walking, Moderate and Vigorous Physical Activity

Directory of Open Access Journals (Sweden)

Katie M. Heinrich

2017-11-01

Full Text Available BackgroundAlthough few United States adults meet physical activity recommendations, those that do are more likely to access to physical activity facilities. Additionally, vigorous exercisers may be more likely to utilize a nearby physical activity facility, while light-to-moderate exercisers are less likely to do so. However, it is unclear what characteristics of those facilities are most important as well as how those characteristics are related to activity intensity.PurposeThis study examined relationships between self-reported leisure-time physical activities and the use of and perceived characteristics of physical activity facilities.MethodsData were from a cross-sectional study in a major metropolitan area. Participants (N = 582; ages 18–74, mean age = 45 ± 14.7 years were more likely to be female (69.9%, Caucasian (65.6%, married (51.7%, and have some college education (72.8%. Household surveys queried leisure-time physical activity, regular physical activity facility use, and importance ratings for key facility characteristics.ResultsLeisure-time physical activity recommendations were met by 41.0% of participants and 50.9% regularly used a physical activity facility. Regular facility use was positively associated with meeting walking (p = 0.036, moderate (p < 0.001, and vigorous (p < 0.001 recommendations. Vigorous exercisers were more likely to use a gym/fitness center (p = 0.006 and to place higher importance on facility quality (p = 0.022, variety of physical activity options offered (p = 0.003, and availability of special equipment and resources (p = 0.01. The facility characteristics of low or free cost (p = 0.02 and offering childcare (p = 0.028 were barriers for walking, and being where friends and family like to go were barriers for moderate leisure-time physical activity (p = 0.013.ConclusionFindings offer insights for structuring interventions using the social ecological

List of DOE radioisotope customers with summary of radioisotope shipments FY 1978

International Nuclear Information System (INIS)

Burlison, J.S.; Laidler, R.I.

1979-05-01

The purpose of the document is to list DOE's radioisotopes production and distribution activities by its facilities at Argonne National Laboratory; Pacific Northwest Laboratory; Brookhaven National Laboratory; Hanford Engineering Development Laboratory; Idaho Operations Office; Los Alamos Scientific Laboratory; Mound Facility; Oak Ridge National Laboratory; Savannah River Laboratory; and UNC Nuclear Industries, Inc

Activation analysis for the IFF system in RAON facility

International Nuclear Information System (INIS)

LEE, Cheol Woo; LEE, Young-Ouk; KIM, Jong Won; KIM, Mijung

2014-01-01

A heavy-ion accelerator facility is under a development in Korea to use in the basic science research and various application areas. In this facility, the In-Flight Fragment (IFF) target and isotope separator has been designed to produce various isotopes and transport the interesting isotopes into the experimental rooms. In this work, activation analysis for the pre-separator was performed in the IFF target room. In this work, activation analysis for the pre-separator was performed for the IFF target system in RAON heavy-ion accelerator facility. At first, radiation source terms were evaluated with the primary beams and target conditions. Using the evaluated source terms, induced activities in all component of pre-separator were calculated. The decay gamma-rays produced after a shutdown was estimated based on the activation analysis and gamma-ray dose rate according to the cooling time was evaluated

The beneficial role of rubble mound coastal structures on seawater oxygenation

Directory of Open Access Journals (Sweden)

E. I. Daniil

2000-10-01

Full Text Available The beneficial role of rubble mound coastal structures on oxygenation under the effect of waves is discussed, based on analytical considerations and experimental data from laboratory experiments with permeable and impermeable structures. Significant oxygenation of the wave-protected area was observed as a result of horizontal transport through the permeable structure. A two-cell model describing the transport of dissolved oxygen (DO near a rubble mound breakwater structure was developed and used for the determination of the oxygen transfer coefficients from the experimental data. Oxygen transfer through the air–water interface is considered a source term in the transport equation and the oxygen flux through the structure is taken into account. The mass transport equations for both sides of the structure are solved analytically in terms of time evolution of DO concentration. The behaviour of the solution is illustrated for three different characteristic cases of initial conditions. The oxygen transfer through the air-water interface in the wave-influenced area increases the DO content in the area; the resulting oxygen flux through the structure is discussed. The analytical results depend on the initial conditions, the oxygen transfer coefficient and the exchange flow rate through the structure. Experiments with impermeable structures show that air water oxygen transfer in the harbour area is negligible in the absence of waves. In addition the ratio of the horizontal DO flux to the vertical flux into the seaward side tends towards a constant value, independent of the initial conditions.Key words: Oceanography: physical (air-sea interactions; surface waves and tides

Classification of burial rituals of the cemeteries without burial mounds in regions of the Tsarevskoe ancient settlement

Directory of Open Access Journals (Sweden)

Nedashkovsky Leonard F.

2015-09-01

Full Text Available Article is dedicated to analysis of burial rituals of the Golden Horde cemeteries without burial mounds in surroundings of the Tsarevskoe ancient settlement. 51 burials (19.9% of total number in mausoleums or in crypts can be attributed as burials of the Golden Horde aristocracy. In the graves found without burial mounds the most wide-spread were of western, south-western and north-western (which could be considered as azimuth deviation from western orientations (they comprise 94.9% of all burials, which are peculiar to the majority of the urban Muslim population of the Golden Horde. However it must be considered that 56 from these burials (21.9% of total number are burials of necropolis of the population of Old Russian settlement of the Vodyanskoe site. Comparing the aristocratic (in mausoleums and crypts burials without burial mounds in the Lower Volga, it is possible conclude that their percentage was significantly higher in the region of the Tsarevskoe settlement, than in other regions; these data allow to assume here the greatest density of residence of settled elite of the Golden Horde. The smallest share of Muslim burials in coffins in the Lower Volga (44.9% and the maximal one of burials with grave goods (13.6% recorded in the region of the Tsarevskoe site. Burial grounds in the region of the Tsarevskoe ancient settlement were in vicinity of the settlements, that is clearly testified about the degree of territorial closeness of cemeteries of settled population of the Golden Horde with urban and rural settlements of the considered period.

Microfossils, a Key to Unravel Cold-Water Carbonate Mound Evolution through Time: Evidence from the Eastern Alboran Sea.

Directory of Open Access Journals (Sweden)

Claudio Stalder

Full Text Available Cold-water coral (CWC ecosystems occur worldwide and play a major role in the ocean's carbonate budget and atmospheric CO2 balance since the Danian (~65 m.y. ago. However their temporal and spatial evolution against climatic and oceanographic variability is still unclear. For the first time, we combine the main macrofaunal components of a sediment core from a CWC mound of the Melilla Mounds Field in the Eastern Alboran Sea with the associated microfauna and we highlight the importance of foraminifera and ostracods as indicators of CWC mound evolution in the paleorecord. Abundances of macrofauna along the core reveal alternating periods dominated by distinct CWC taxa (mostly Lophelia pertusa, Madrepora oculata that correspond to major shifts in foraminiferal and ostracod assemblages. The period dominated by M. oculata coincides with a period characterized by increased export of refractory organic matter to the seafloor and rather unstable oceanographic conditions at the benthic boundary layer with periodically decreased water energy and oxygenation, variable bottom water temperature/density and increased sediment flow. The microfaunal and geochemical data strongly suggest that M. oculata and in particular Dendrophylliidae show a higher tolerance to environmental changes than L. pertusa. Finally, we show evidence for sustained CWC growth during the Alleröd-Younger-Dryas in the Eastern Alboran Sea and that this period corresponds to stable benthic conditions with cold/dense and well oxygenated bottom waters, high fluxes of labile organic matter and relatively strong bottom currents.

GeoBioScience: Red Wood Ants as Bioindicators for Active Tectonic Fault Systems in the West Eifel (Germany

Directory of Open Access Journals (Sweden)

Ulrich Schreiber

2013-05-01

Full Text Available In a 1.140 km² study area of the volcanic West Eifel, a comprehensive investigation established the correlation between red wood ant mound (RWA; Formica rufa-group sites and active tectonic faults. The current stress field with a NW-SE-trending main stress direction opens pathways for geogenic gases and potential magmas following the same orientation. At the same time, Variscan and Mesozoic fault zones are reactivated. The results showed linear alignments and clusters of approx. 3,000 RWA mounds. While linear mound distribution correlate with strike-slip fault systems documented by quartz and ore veins and fault planes with slickensides, the clusters represent crosscut zones of dominant fault systems. Latter can be correlated with voids caused by crustal block rotation. Gas analyses from soil air, mineral springs and mofettes (CO2, Helium, Radon and H2S reveal limiting concentrations for the spatial distribution of mounds and colonization. Striking is further the almost complete absence of RWA mounds in the core area of the Quaternary volcanic field. A possible cause can be found in occasionally occurring H2S in the fault systems, which is toxic at miniscule concentrations to the ants. Viewed overall, there is a strong relationship between RWA mounds and active tectonics in the West Eifel.

Optimal reproduction strategies in two species of mound-building termites.

Science.gov (United States)

Cameron, David A; Ivers, David J; Evans, Theodore A; Myerscough, Mary R

2008-01-01

We formulate a mathematical model for food collection and production of workers and nymphs in 2 species of mound building termites. We maximise the number of nymphs (reproductives) produced by each colony over its lifetime with respect to the proportion of eggs that hatch as nymphs as opposed to workers. The results predict that food storage has a very important influence on the pattern of nymph and worker production. Food storage affects the part of the year that nymph production dominates, whether nymphs and workers are produced at the same time or not, and the existence of a final phase in the colony's life when a very large number of nymphs but no workers are produced.

Research activities by INS cyclotron facility

International Nuclear Information System (INIS)

1992-06-01

Research activities made by the cyclotron facility and the related apparatuses at Institute for Nuclear Study (INS), University of Tokyo, have been reviewed in terms of the associated scientific publications. This publication list, which is to be read as a continuation of INS-Rep.-608 (October, 1986), includes experimental works on low-energy nuclear physics, accelerator technology, instrumental developments, radiation physics and other applications in interdisciplinary fields. The publications are classified into the following four categories. (A) : Internal reports published in INS. (B) : Publications in international scientific journals on experimental research works done by the cyclotron facility and the related apparatuses at INS. Those made by outside users are also included. (C) : Publications in international scientific journals on experimental low-energy nuclear physics, which have been done by the staff of INS Nuclear Physics Division using facilities outside INS. (D) : Contributions to international conferences. (author)

Timing of mounding for bambara groundnut affects crop development and yield in a rainfed tropical environment

DEFF Research Database (Denmark)

Ouedrago, Mahama; M'bi, Bertin Zagre; Liu, Fulai

2013-01-01

-ecological zone of Burkina Faso were conducted. Yield data confirm the findings from a drier part of Burkina Faso; i.e., mounding of bambara groundnut should not be carried out around the time of flowering. In a semi-arid area, such as Sudan–Sahel agro-ecological zone and with germplasm maturing within 90 days...

The relationship between sports facility accessibility and physical activity among Korean adults

Directory of Open Access Journals (Sweden)

Sang Ah Lee

2016-08-01

Full Text Available Abstract Background The benefits of physical activity on physical and mental health are well known. The accessibility of sports facilities is reported to have considerable association with the amount of physical activity a person participates in. Therefore, we investigated the association between subjectively assessed accessibility of sports facilities and physical activity among Korean adults. Methods We obtained data from the 2012 Community Health Survey. Physical activity was measured based on weekly metabolic equivalent task (MET hours according to the International Physical Activity Questionnaire (IPAQ. Sociodemographic, economic, and health variables were used as covariates in a logistic regression model. Results A total 201,723 participants were included in this study. Participants with easy access to sports facilities participated in physical activity more often than those without easy access (OR = 1.16, 95 % CI 1.13–1.20. More physical activity was generally observed if participants had a history of depression or if participants were among the white-collar or urban subgroups. Conclusion Our results showed that the accessibility of sports facilities is associated with physical activity. Therefore, it is crucial to consider the accessibility of sports facilities when promoting an environment conducive to physical activity or designing programs for enhancing physical activity.

Impact of termite activity on soil environment: A perspective from their soluble chemical components

International Nuclear Information System (INIS)

Semhi, K.; Chaudhuri, S.; Clauer, N.; Boeglin, J. L.

2008-01-01

An investigation on varied types of termite mounds relative to the nearby soils that are not inhabited by the termites in different places of Cameroon show that the activity of the termites is increasing the contents of most major and some trace elements in the termite mounds, except for Si and sometimes Fe, Mn, Na and K. These released elements are relocated into newly formed mineral phases that are dissolved by either H 2 O dilute HCl leaching. The Ca and Mn released by the termite activity testify for crystallization of Ca-Mg carbonates and phosphates as well as of Fe oxy-hydroxides and/or Mn hydroxides. Termite activity also induces an increase in the lanthanide contents, the mound materials being especially enriched in light lanthanides relative to the corresponding soils without termite activity. The shapes of the patterns support precipitation of Mn-Fe oxy-hydroxides and Ca carbonates-phosphates. The increased amounts of Eu and Ce linked to termite activity seem to relate to the occurrence of reducing agents that are released by the termites, modifying Eu +3 into Eu +2 and Ce +4 into Ce +3 , favoring in turn selective incorporation of Eu +2 and Ce +3 in the new phases of the termite mounds. Another consequence of the termite activity is the precipitation of H 2 O and HCl extractable phases having low Sr/Ca ratios. Even if the K/Rb values of the termite mounds are typical for common soil-forming silicate minerals, their relocation by an inorganic process alone does not explain an abnormally high ratio in the H 2 O leachable mineral phases. It was also shown that the main source for K and Rb of the dissolved phases is not only the interlayer site of clay particles, but also nutrients immobilized in and by the termites

Contributions of gopher mound and casting disturbances to plant community structure in a Cascade Range meadow complex

Science.gov (United States)

M. Case; C.B. Halpern; S.A. Levin

2013-01-01

Pocket gophers (Geomyidae) are major agents of disturbance in North American grasslands. Gopher mounds bury existing plants and influence community structure through various mechanisms. However, in mountain meadows that experience winter snowpack, gophers also create winter castings, smaller tube-shaped deposits, previously ignored in studies of plant–gopher...

Neutron dosimetry program at Mound - problems and solutions

International Nuclear Information System (INIS)

Winegardner, M.K.

1991-01-01

The Mound personnel neutron dosimetry program utilizes TLD albedo technology. The neutron dosimeter design incorporates a two-element spectrometer for site-specific neutron quality determination and empirical application of field neutron calibration factors. Design elements feature two Li(6)F (TLD- 600) chips for neutron detection and one Li(7)F (TLD-700) chip for gamma compensation of the TLD- 600 chips. One TLD-600 chip is Cadmium shielded on the front side of the dosimeter, the other is Cadmium shielded from the back side. Tin filters are placed opposite of the Cadmium shield on each of the TLD-600 chips and on both sides of the TLD-700 chip for symmetrically equivalent gamma absorption characteristics. Neutron quality determination is accomplished by the albedo neutron-to- incident thermal neutron response ratio above the Cadmium cutoff. This front Cadmium shielded-to-back Cadmium shielded response ratio, compensated for the presence of gamma radiation, provides the basis for neutron energy calibration via the albedo response curve

Fluid-chemical evidence for one billion years of fluid flow through Mesoproterozoic deep-water carbonate mounds (Nanisivik zinc district, Nunavut)

Science.gov (United States)

Hahn, K. E.; Turner, E. C.; Kontak, D. J.; Fayek, M.

2018-02-01

Ancient carbonate rocks commonly contain numerous post-depositional phases (carbonate minerals; quartz) recording successive diagenetic events that can be deciphered and tied to known or inferred geological events using a multi-pronged in situ analytical protocol. The framework voids of large, deep-water microbial carbonate seep-mounds in Arctic Canada (Mesoproterozoic Ikpiarjuk Formation) contain multiple generations of synsedimentary and late cement. An in situ analytical study of the post-seafloor cements used optical and cathodoluminescence petrography, SEM-EDS analysis, fluid inclusion (FI) microthermometry and evaporate mound analysis, LA-ICP-MS analysis, and SIMS δ18O to decipher the mounds' long-term diagenetic history. The six void-filling late cements include, in paragenetic order: inclusion-rich euhedral dolomite (ED), finely crystalline clear dolomite (FCD), hematite-bearing dolomite (HD), coarsely crystalline clear dolomite (CCD), quartz (Q), replacive calcite (RC) and late calcite (LC). Based on the combined analytical results, the following fluid-flow history is defined: (1) ED precipitation by autocementation during shallow burial (fluid 1; Mesoproterozoic); (2) progressive mixing of Ca-rich hydrothermal fluid with the connate fluid, resulting in precipitation of FCD followed by HD (fluid 2; also Mesoproterozoic); (3) precipitation of hydrothermal dolomite (CCD) from high-Ca and K-rich fluids (fluid 3; possibly Mesoproterozoic, but timing unclear); (4) hydrothermal Q precipitation (fluid 4; timing unclear), and (5) RC and LC precipitation from a meteoric-derived water (fluid 5) in or since the Mesozoic. Fluids associated with FCD, HD, and CCD may have been mobilised during deposition of the upper Bylot Supergroup; this time interval was the most tectonically active episode in the region's Mesoproterozoic to Recent history. The entire history of intermittent fluid migration and cement precipitation recorded in seemingly unimportant void

SEM facility for examination of reactive and radioactive materials

International Nuclear Information System (INIS)

Downs, G.L.; Tucker, P.A.

1977-01-01

A scanning electron microscope (SEM) facility for the examination of tritium-containing materials is operational at Mound Laboratory. The SEM is installed with the sample chamber incorporated as an integral part of an inert gas glovebox facility to enable easy handling of radioactive and pyrophoric materials. A standard SEM (ETEC Model B-1) was modified to meet dimensional, operational, and safety-related requirements. a glovebox was designed and fabricated which permitted access with the gloves to all parts of the SEM sample chamber to facilitate director and accessory replacement and repairs. A separate console combining the electron optical column and specimen chamber was interfaced to the glovebox by a custom-made, neoprene bellows so that the vibrations normally associated with the blowers and pumps were damped. Photomicrographs of tritiated pyrophoric materials show the usefulness of this facility. Some of the difficulties involved in the investigation of these materials are also discussed. The SEM is also equipped with an energy dispersive x-ray detector (ORTEC) and a Secondary Ion Mass Spectrometer (3M) attachments. This latter attachment allows analysis of secondary ions with masses ranging from 1-300 amu. (Auth.)

Discernibility of Burial Mounds in High-Resolution X-Band SAR Images for Archaeological Prospections in the Altai Mountains

Directory of Open Access Journals (Sweden)

Timo Balz

2016-09-01

Full Text Available The Altai Mountains are a heritage-rich archaeological landscape with monuments in almost every valley. Modern nation state borders dissect the region and limit archaeological landscape analysis to intra-national areas of interest. Remote sensing can help to overcome these limitations. Due to its high precision, Synthetic Aperture Radar (SAR data can be a very useful tool for supporting archaeological prospections, but compared to optical imagery, the detectability of sites of archaeological interest is limited. We analyzed the limitations of SAR using TerraSAR-X images in different modes. Based on ground truth, the discernibility of burial mounds was analyzed in different SAR acquisition modes. We show that very-high-resolution TerraSAR-X staring spotlight images are very well suited for the task, with >75% of the larger mounds being discernible, while in images with a lower spatial resolution only a few large sites can be detected, at rates below 50%.

Stable isotope sales: Mound Laboratory customer and shipment summaries, FY 1976 and FY 1976A

International Nuclear Information System (INIS)

Ruwe, A.H. Jr.

1977-01-01

A listing is given of Mound Laboratory's sales of stable isotopes of noble gases, carbon, oxygen, nitrogen, chlorine, and sulfur for fiscal years 1976 and 1976A (the period July 1, 1975 through September 30, 1976). Purchasers are listed alphabetically and are divided into domestic and foreign groups. A cross-reference index by location is included for domestic customers. Cross-reference listings by isotope purchased are included for all customers

Computer aided optimum design of rubble-mound breakwater cross-sections : Manual of the RUMBA computer package, release 1

NARCIS (Netherlands)

De Haan, W.

1989-01-01

The computation of the optimum rubble-mound breakwater crosssection is executed on a micro-computer. The RUMBA computer package consists of two main parts: the optimization process is executed by a Turbo Pascal programme, the second part consists of editing functions written in AutoLISP. AutoLISP is

Quantifying Detection Probabilities for Proliferation Activities in Undeclared Facilities

International Nuclear Information System (INIS)

Listner, C.; Canty, M.; Niemeyer, I.; Rezniczek, A.; Stein, G.

2015-01-01

International Safeguards is currently in an evolutionary process to increase effectiveness and efficiency of the verification system. This is an obvious consequence of the inability to detect the Iraq's clandestine nuclear weapons programme in the early 90s. By the adoption of the Programme 93+2, this has led to the development of Integrated Safeguards and the State-level concept. Moreover, the IAEA's focus was extended onto proliferation activities outside the State's declared facilities. The effectiveness of safeguards activities within declared facilities can and have been quantified with respect to costs and detection probabilities. In contrast, when verifying the absence of undeclared facilities this quantification has been avoided in the past because it has been considered to be impossible. However, when balancing the allocation of budget between the declared and the undeclared field, explicit reasoning is needed why safeguards effort is distributed in a given way. Such reasoning can be given by a holistic, information and risk-driven approach to Acquisition Path Analysis comprising declared and undeclared facilities. Regarding the input, this approach relies on the quantification of several factors, i.e., costs of attractiveness values for specific proliferation activities, potential safeguards measures and detection probabilities for these measures also for the undeclared field. In order to overcome the lack of quantification for detection probabilities in undeclared facilities, the authors of this paper propose a general verification error model. Based on this model, four different approaches are explained and assessed with respect to their advantages and disadvantages: the analogy approach, the Bayes approach, the frequentist approach and the process approach. The paper concludes with a summary and an outlook on potential future research activities. (author)

Experimental Study of Wave Field Around the Outer Part of a Rubble Mound Roundhead Solution for the new Port of La Coruña at Punto Langosteira

DEFF Research Database (Denmark)

Burcharth, Hans F.; Pedersen, Thomas Schmidt

The wave agitation in the port and at the entrance to the port depends on the length of the outer part of the breakwater (west of the spur breakwater) and on the type of structure, e.g. caissons or rubble mound. In the present study is investigated the wave field around a rubble mound head armoured...... port basin and berths. The calibrated numerical model can then be used for the study of the optimum length and type of the outer breakwater structure....

The Guaymas Basin hiking guide to hydrothermal mounds, chimneys and microbial mats: complex seafloor expressions of subsurface hydrothermal circulation

Directory of Open Access Journals (Sweden)

Andreas eTeske

2016-02-01

Full Text Available The hydrothermal mats, mounds and chimneys of the southern Guaymas Basin are the surface expression of complex subsurface hydrothermal circulation patterns. In this overview we document the most frequently visited features of this hydrothermal area with photographs, temperature measurements, and selected geochemical data; many of these distinct habitats await characterization of their microbial communities and activities. Microprofiler deployments on microbial mats and hydrothermal sediments show their steep geochemical and thermal gradients at millimeter-scale vertical resolution. Mapping these hydrothermal features and sampling locations within the southern Guaymas Basin suggest linkages to underlying shallow sills and heatflow gradients. Recognizing the inherent spatial limitations of much current Guaymas Basin sampling calls for a wider survey of the entire spreading region.

Effect of termite activity on soil under different land management strategies

Directory of Open Access Journals (Sweden)

Liane Barreto Alves Pinheiro

2017-03-01

Full Text Available Mound-building termites are important agents of soil bioperturbation, but these species have not been extensively studied thus far. The present study aimed to evaluate the soil particle-size and the chemical attributes of termite mounds and the surrounding soil under different land use strategies. A one-hectare plot was defined for an unmanaged degraded pasture, planted pasture, and for a eucalyptus Corymbia citriodora plantation. In each plot, the top, center, and base sections of five Cornitermes cumulans mounds, and the surrounding soil at the depths of 0-5; 5-10; 10-20 cm, were sampled in the Pinheiral, Rio de Janeiro state. In the three areas, the center of the mounds contained higher clay content, organic carbon, phosphorous, calcium and magnesium, total bases, and cation exchangeable capacity, when compared to the top, base, and the surrounding soils. However, the center had lower values of exchangeable acidity and potassium, of the three areas. In the eucalyptus plantation, the values of pH, total bases, calcium, and magnesium were lower, whereas aluminum, exchangeable acidity, sodium, and cation exchange capacity were higher both in the mounds and in the surrounding soil, in relation to the pastures. There were no differences among the three areas in terms of organic carbon, potassium, phosphorous, and total bases, in the mounds and adjacent soil. Thus, the termite activity altered the clay content and most of the soil chemical properties in all of the studied areas, but only for the center of the mounds. However, the effect of these organisms was different in the eucalyptus plantation in relation to the pasture areas.

Duff mound consumption and cambium injury for centuries-old western larch from prescribed burning in western Montana

Science.gov (United States)

Michael G. Harrington

2012-01-01

Western larch is one of the most fire-adapted conifers in western North America. Its historical perpetuation depended upon regular fire disturbances, which creates open stand conditions and mineral seedbeds. A stand of 200- to 500-year-old larch in western Montana with deep duff mounds resulting from an unusually long 150-year fire-free period was mechanically thinned...

DESIGN OF FILL AND FINISH FACILITY FOR ACTIVE PHARMACEUTICAL INGREDIENTS (API

Directory of Open Access Journals (Sweden)

NUUR LAILA KHAIRUDDIN

2016-08-01

Full Text Available Fill and finish operations continue to be one of the most heavily outsourced activities in the biopharmaceutical manufacturing market today. There are a few aspects that need to be consider in outsource activities like logistic, storage condition, facility certification and audit as regulations and standards which the manufacturer should adhere. Risk would be greater and extra care should be taken when outsource from foreign fill and finish facility. Thus, the internal aseptic fill and finish facility with audit checklist will help to minimize the risk during logistic and storage and also minimize the cost for outsource fill and finish facility. The data collections are through survey and conceptual design with simulation as the execution part.

Associations between Moderate-to-Vigorous Physical Activity and Neighbourhood Recreational Facilities: The Features of the Facilities Matter

Directory of Open Access Journals (Sweden)

Ka Yiu Lee

2014-12-01

Full Text Available Objectives: To examine the associations between objectively-assessed moderate-to-vigorous physical activity (MVPA and perceived/objective measures of neighbourhood recreational facilities categorized into indoor or outdoor, public, residential or commercial facilities. The associations between facility perceptions and objectively-assessed numbers of recreational facilities were also examined. Method: A questionnaire was used on 480 adults to measure local facility perceptions, with 154 participants wearing ActiGraph accelerometers for ≥4 days. The objectively-assessed number of neighbourhood recreational facilities were examined using direct observations and Geographical Information System data. Results: Both positive and negative associations were found between MVPA and perceived/objective measures of recreational facilities. Some associations depended on whether the recreational facilities were indoor or outdoor, public or residential facilities. The objectively-assessed number of most public recreational facilities was associated with the corresponding facility perceptions, but the size of effect was generally lower than for residential recreational facilities. Conclusions: The objectively-assessed number of residential outdoor table tennis courts and public indoor swimming pools, the objectively-assessed presence of tennis courts and swimming pools, and the perceived presence of bike lanes and swimming pools were positive determinants of MVPA. It is suggested to categorize the recreational facilities into smaller divisions in order to identify unique associations with MVPA.

PRELIMINARY BIOGEOCHEMICAL DATA ON MICROBIAL CARBONATOGENESIS IN ANCIENT EXTREME ENVIRONMENTS (KESS-KESS MOUNDS, MOROCCO

Directory of Open Access Journals (Sweden)

ADRIANO GUIDO

2013-03-01

Full Text Available The Devonian Kess-Kess mounds, cropping out in the Hamar Laghdad Ridge (SE Morocco, provide a useful case-study for understanding the relationships between the microbial metabolic activities and micrite precipitation in an extreme environment. Very fine dark and white wrinkled laminae record microbial activity and the geochemistry of the organic matter allows the  characterization of the source organisms. The biogeochemical characterization of extracted organic matter was performed through the functional group analyses by FT-IR Spectroscopy. FT-IR parameters indicate a marine origin and low thermal evolution for the organic material. The organic matter is characterized by the presence of stretching ?C=C vibrations attributable to alkene and/or unsaturated carboxylic acids. Preliminary analysis with GC-MS provides evidence for an autochthonous (

Stable isotope sales: Mound Laboratory customer and shipment summaries, FY 1976 and FY 1976A

Energy Technology Data Exchange (ETDEWEB)

Ruwe, A.H. Jr. (comp.)

1977-06-06

A listing is given of Mound Laboratory's sales of stable isotopes of noble gases, carbon, oxygen, nitrogen, chlorine, and sulfur for fiscal years 1976 and 1976A (the period July 1, 1975 through September 30, 1976). Purchasers are listed alphabetically and are divided into domestic and foreign groups. A cross-reference index by location is included for domestic customers. Cross-reference listings by isotope purchased are included for all customers.

An electric and electromagnetic geophysical approach for subsurface investigation of anthropogenic mounds in an urban environment

Science.gov (United States)

Pazzi, Veronica; Tapete, Deodato; Cappuccini, Luca; Fanti, Riccardo

2016-11-01

Scientific interest in mounds as geomorphological features that currently represent topographic anomalies in flat urban landscapes mainly lies on the understanding of their origin, either purely natural or anthropogenic. In this second circumstance, another question is whether traces of lost buildings are preserved within the mound subsurface and can be mapped as remnants testifying past settlement. When these landforms have been modified in centuries for civilian use, structural stability is a further element of concern. To address these issues we applied a geophysical approach based on a very low frequency electromagnetic (VLF-EM) technique and two-dimensional electrical resistivity tomography (2D-ERT) and integrated it with well-established surface survey methods within a diagnostic workflow of structural assessment. We demonstrate the practical benefits of this method in the English Cemetery of Florence, Italy, whose mixed nature and history of morphological changes are suggested by archival records. The combination of the two selected geophysical techniques allowed us to overcome the physical obstacles caused by tomb density and to prevent interference from the urban vehicular traffic on the geophysical signals. Eighty-two VLF-EM profiles and five 2D-ERTs were collected to maximise the spatial coverage of the subsurface prospection, while surface indicators of instability (e.g., tomb tilt, location, and direction of ground fractures and wall cracks) were mapped by standard metric survey. High resistive anomalies (> 300 and 400 Ωm) observed in VLF-EM tomographies are attributed to remnants of the ancient perimeter wall that are still buried along the southern side of the mound. While no apparent correlation is found between the causes of tomb and ground movements, the crack pattern map supplements the overall structural assessment. The main outcome is that the northern portion of the retaining wall is classed with the highest hazard rate. The impact of this

49 CFR 37.61 - Public transportation programs and activities in existing facilities.

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false Public transportation programs and activities in... TRANSPORTATION SERVICES FOR INDIVIDUALS WITH DISABILITIES (ADA) Transportation Facilities § 37.61 Public transportation programs and activities in existing facilities. (a) A public entity shall operate a designated...

Adolescents' physical activity: competition between perceived neighborhood sport facilities and home media resources.

Science.gov (United States)

Wong, Bonny Yee-Man; Cerin, Ester; Ho, Sai-Yin; Mak, Kwok-Kei; Lo, Wing-Sze; Lam, Tai-Hing

2010-04-01

To examine the independent, competing, and interactive effects of perceived availability of specific types of media in the home and neighborhood sport facilities on adolescents' leisure-time physical activity (PA). Survey data from 34 369 students in 42 Hong Kong secondary schools were collected (2006-07). Respondents reported moderate-to-vigorous leisure-time PA, presence of sport facilities in the neighborhood and of media equipment in the home. Being sufficiently physically active was defined as engaging in at least 30 minutes of non-school leisure-time PA on a daily basis. Logistic regression and post-estimation linear combinations of regression coefficients were used to examine the independent and competing effects of sport facilities and media equipment on leisure-time PA. Perceived availability of sport facilities was positively (OR(boys) = 1.17; OR(girls) = 1.26), and that of computer/Internet negatively (OR(boys) = 0.48; OR(girls) = 0.41), associated with being sufficiently active. A significant positive association between video game console and being sufficiently active was found in girls (OR(girls) = 1.19) but not in boys. Compared with adolescents without sport facilities and media equipment, those who reported sport facilities only were more likely to be physically active (OR(boys) = 1.26; OR(girls) = 1.34), while those who additionally reported computer/Internet were less likely to be physically active (OR(boys) = 0.60; OR(girls) = 0.54). Perceived availability of sport facilities in the neighborhood may positively impact on adolescents' level of physical activity. However, having computer/Internet may cancel out the effects of active opportunities in the neighborhood. This suggests that physical activity programs for adolescents need to consider limiting the access to computer-mediated communication as an important intervention component.

Evaluation of groundwater monitoring results at the Hanford Site 200 Area Treated Effluent Disposal Facility

International Nuclear Information System (INIS)

Barnett, D.B.

1998-09-01

The Hanford Site 200 Area Treated Effluent Disposal Facility (TEDF) has operated since June 1995. Groundwater monitoring has been conducted quarterly in the three wells surrounding the facility since 1992, with contributing data from nearby B Pond System wells. Cumulative hydrologic and geochemical information from the TEDF well network and other surrounding wells indicate no discernable effects of TEDF operations on the uppermost aquifer in the vicinity of the TEDF. The lateral consistency and impermeable nature of the Ringold Formation lower mud unit, and the contrasts in hydraulic conductivity between this unit and the vadose zone sediments of the Hanford formation suggest that TEDF effluent is spreading laterally with negligible mounding or downward movement into the uppermost aquifer. Hydrographs of TEDF wells show that TEDF operations have had no detectable effects on hydraulic heads in the uppermost aquifer, but show a continuing decay of the hydraulic mound generated by past operations at the B Pond System. Comparison of groundwater geochemistry from TEDF wells and other, nearby RCRA wells suggests that groundwater beneath TEDF is unique; different from both effluent entering TEDF and groundwater in the B Pond area. Tritium concentrations, major ionic proportions, and lower-than-background concentrations of other species suggest that groundwater in the uppermost aquifer beneath the TEDF bears characteristics of water in the upper basalt confined aquifer system. This report recommends retaining the current groundwater well network at the TEDF, but with a reduction of sampling/analysis frequency and some modifications to the list of constituents sought

Application of the management system for facilities and activities. Safety guide

International Nuclear Information System (INIS)

2006-01-01

This Safety Guide supports the Safety Requirements publication on The Management System for Facilities and Activities. It provides generic guidance to aid in establishing, implementing, assessing and continually improving a management system that complies with the requirements established. In addition to this Safety Guide, there are a number of Safety Guides for specific technical areas. Together these provide all the guidance necessary for implementing these requirements. This publication supersedes Safety Series No. 50-SG-Q1-Q7 (1996). The guidance provided here may be used by organizations in the following ways: - To assist in the development of the management systems of organizations directly responsible for operating facilities and activities and providing services for: Nuclear facilities; Activities using sources of ionizing radiation; Radioactive waste management; The transport of radioactive material; Radiation protection activities; Any other practices or circumstances in which people may be exposed to radiation from naturally occurring or artificial sources; The regulation of such facilities and activities; - To assist in the development of the management systems of the relevant regulatory bodies; - By the operator, to specify to a supplier, via contractual documentation, any guidance of this Safety Guide that should be included in the supplier's management system for the supply and delivery of products

Technical note: Rapid image-based field methods improve the quantification of termite mound structures and greenhouse-gas fluxes

Directory of Open Access Journals (Sweden)

P. A. Nauer

2018-06-01

Full Text Available Termite mounds (TMs mediate biogeochemical processes with global relevance, such as turnover of the important greenhouse gas methane (CH4. However, the complex internal and external morphology of TMs impede an accurate quantitative description. Here we present two novel field methods, photogrammetry (PG and cross-sectional image analysis, to quantify TM external and internal mound structure of 29 TMs of three termite species. Photogrammetry was used to measure epigeal volume (VE, surface area (AE and mound basal area (AB by reconstructing 3-D models from digital photographs, and compared against a water-displacement method and the conventional approach of approximating TMs by simple geometric shapes. To describe TM internal structure, we introduce TM macro- and micro-porosity (θM and θμ, the volume fractions of macroscopic chambers, and microscopic pores in the wall material, respectively. Macro-porosity was estimated using image analysis of single TM cross sections, and compared against full X-ray computer tomography (CT scans of 17 TMs. For these TMs we present complete pore fractions to assess species-specific differences in internal structure. The PG method yielded VE nearly identical to a water-displacement method, while approximation of TMs by simple geometric shapes led to errors of 4–200 %. Likewise, using PG substantially improved the accuracy of CH4 emission estimates by 10–50 %. Comprehensive CT scanning revealed that investigated TMs have species-specific ranges of θM and θμ, but similar total porosity. Image analysis of single TM cross sections produced good estimates of θM for species with thick walls and evenly distributed chambers. The new image-based methods allow rapid and accurate quantitative characterisation of TMs to answer ecological, physiological and biogeochemical questions. The PG method should be applied when measuring greenhouse-gas emissions from TMs to avoid large errors from inadequate shape

The environment and urban adolescents' use of recreational facilities for physical activity: a qualitative study.

Science.gov (United States)

Ries, Amy V; Gittelsohn, Joel; Voorhees, Carolyn C; Roche, Kathleen M; Clifton, Kelly J; Astone, Nan M

2008-01-01

Investigate environmental factors influencing the use of recreational facilities for physical activity by urban African-American adolescents. Qualitative in-depth interviews and direct observation. Two public high schools and 24 public recreational facilities in Baltimore, Maryland. Forty-eight African-American adolescents aged 14 to 18 years. Data from 48 in-depth interviews and 26 observations were coded using NVivo software and analyzed using the constant comparative method. Facility use is influenced by characteristics of the physical, social, organizational, and economic environments. Adolescents are attracted to low-cost, well-maintained facilities that offer preferred activities and that are within close proximity to home. Adolescents with limited access to facilities use alternative play spaces, like the streets or vacant lots, where they risk injury from falling or being hit by a car. They are drawn to facilities where they find active adolescents, and they avoid those where young people are engaged in drug or gang activity. Concerns about facility safety largely determine use, particularly for adolescent girls. Previous research points to the importance of increasing facility availability as a means of promoting physical activity, particularly in minority communities in which availability is disproportionately limited. This study shows that, while availability is important, additional facility characteristics should be considered when using environmental change to promote facility use for physical activity.

Photogrammetric analysis of rubble mound breakwaters scale model tests

Directory of Open Access Journals (Sweden)

João Rodrigues

2016-09-01

Full Text Available The main goal of this paper is to develop a photogrammetric method in order to obtain arobust tool for damage assessment and quantification of rubble-mound armour layers during physicalscale model tests. With the present work, an innovative approach based on a reduced number ofdigital photos is proposed to support the identification of affected areas. This work considers twosimple digital photographs recording the instants before and after the completion of the physicaltest. Mathematical techniques were considered in the development of the procedures, enabling thetracking of image differences between photos. The procedures were developed using an open-sourceapplication, Scilab, nevertheless they are not platform dependent. The procedures developed enablethe location and identity of eroded areas in the breakwater armour layer, as well as the possibilityof quantifying them. This ability is confirmed through the calculation of correlation coefficients ineach step of the search for the more damaged area. It is also possible to make an assessment of themovement of armour layer units.

Wave Run-up on the Zeebrugge Rubble Mound Breakwater

DEFF Research Database (Denmark)

De Rouck, Julien; Van de Walle, Björn; Troch, Peter

2007-01-01

A clear difference between full-scale wave run-up measurements and small-scale model test results had been noticed during a MAST II project. This finding initiated a thorough study of wave run-up through the European MAST III OPTICREST project. Full-scale measurement have been carried out...... on the Zeebrugge rubble mound breakwater. This breakwater has been modeled in three laboratories: two 2D models at a scale of 1:30 and one 3D model at a scale of 1:40 have been buildt at Flanders Hydraulics (Belgium), at Universidad Politécnica de Valencia (Spain), and at Aalborg University (Denmark). Wave run......-up has been measured by a digital run-up gauge. This gauge has proven to measure wave run-up more accurately than the traditional wire gauge. Wave spectra measured in Zeebrugge have been reproduced in the laboratories. Results of small-scale model tests and full-scale measurements results have been...

Mesopotamian ceramics from the burial mounds of Bahrain, c.2250–1750 BC

DEFF Research Database (Denmark)

Laursen, Steffen

2011-01-01

in Mesopotamia’s interaction with the populations of the ‘Lower Sea’. The first import horizon is comprised of a vessel type found exclusively in the scattered mounds of Early Type which pre-date the rise of the Dilmun ‘state’ proper. The distribution of these vessels outside their areas of production...... demonstrates how they circulated widely in a network elsewhere considered to reflect the orbit of Mesopotamia’s late third-millennium ‘Magan trade’. Here it is consequently concluded that this particular type represents an important fossile directeur of the ‘Magan trade’ and pre-Dilmun florescence. The vessels...

Evaluation of brine disposal from the Bryan Mound site of the strategic petroleum reserve program. Final report

Energy Technology Data Exchange (ETDEWEB)

Case, Robert J.; Chittenden, Jr, Mark E.; Harper, Jr, Donald E.; Kelly, Jr, Francis J.; Loeblich, Laurel A.; McKinney, Larry D.; Minello, Thomas J.; Park, E. Taisoo; Randall, Robert E.; Slowey, J. Frank

1981-01-01

On March 10, 1980, the Department of Energy's Strategic Petroleum Reserve Program began leaching the Bryan Mound salt dome and discharging the resulting brine into the coastal waters off Freeport, Texas. During the months of March and April, a team of scientists and engineers from Texas A and M University conducted an intensive environmental study of the area surrounding the diffuser site. A pipeline has been laid from the Bryan Mound site to a location 12.5 statute miles (20 km) offshore. The last 3060 ft (933 m) of this pipeline is a 52-port diffuser through which brine can be discharged at a maximum rate of 680,000 barrels per day. Initially, 16 ports were open which permitted a maximum discharge rate of 350,000 barrels per day and a continuous brine discharge was achieved on March 13, 1980. The purpose of this report is to describe the findings of the project team during the intensive postdisposal study period of March and April, 1980. The major areas of investigation are physical oceanography, analysis of the discharge plume, water and sediment quality, nekton, benthos, phytoplankton, zooplankton, and data management.

Temporal Characterization of Hydrates System Dynamics beneath Seafloor Mounds. Integrating Time-Lapse Electrical Resistivity Methods and In Situ Observations of Multiple Oceanographic Parameters

Energy Technology Data Exchange (ETDEWEB)

Lutken, Carol [Univ. of Mississippi, Oxford, MS (United States); Macelloni, Leonardo [Univ. of Mississippi, Oxford, MS (United States); D' Emidio, Marco [Univ. of Mississippi, Oxford, MS (United States); Dunbar, John [Univ. of Mississippi, Oxford, MS (United States); Higley, Paul [Univ. of Mississippi, Oxford, MS (United States)

2015-01-31

This study was designed to investigate temporal variations in hydrate system dynamics by measuring changes in volumes of hydrate beneath hydrate-bearing mounds on the continental slope of the northern Gulf of Mexico, the landward extreme of hydrate occurrence in this region. Direct Current Resistivity (DCR) measurements were made contemporaneously with measurements of oceanographic parameters at Woolsey Mound, a carbonate-hydrate complex on the mid-continental slope, where formation and dissociation of hydrates are most vulnerable to variations in oceanographic parameters affected by climate change, and where changes in hydrate stability can readily translate to loss of seafloor stability, impacts to benthic ecosystems, and venting of greenhouse gases to the water-column, and eventually, the atmosphere. We focused our study on hydrate within seafloor mounds because the structurally-focused methane flux at these sites likely causes hydrate formation and dissociation processes to occur at higher rates than at sites where the methane flux is less concentrated and we wanted to maximize our chances of witnessing association/dissociation of hydrates. We selected a particularly well-studied hydrate-bearing seafloor mound near the landward extent of the hydrate stability zone, Woolsey Mound (MC118). This mid-slope site has been studied extensively and the project was able to leverage considerable resources from the team’s research experience at MC118. The site exhibits seafloor features associated with gas expulsion, hydrates have been documented at the seafloor, and changes in the outcropping hydrates have been documented, photographically, to have occurred over a period of months. We conducted observatory-based, in situ measurements to 1) characterize, geophysically, the sub-bottom distribution of hydrate and its temporal variability, and 2) contemporaneously record relevant environmental parameters (temperature, pressure, salinity, turbidity, bottom currents) to

Including the influence of waves in the overall slope stability analysis of rubble mound breakwaters

OpenAIRE

Mollaert, J.; Tavallali, A.

2016-01-01

An offshore breakwater is designed for the construction of a LNG-terminal. For the slope stability analysis of the rubble mound breakwater the existing and the extreme wave climate are considered. Pore water pressure variations exist in the breakwater and its permeable foundation. A wave trough combined with the moment of maximum wave run-up results in a decrease and increase of the pore water pressure, respectively. Therefore, the wave actions have on overall effect on the slope stability of...

Distribution of physical activity facilities in Scotland by small area measures of deprivation and urbanicity

Directory of Open Access Journals (Sweden)

Ogilvie David

2010-10-01

Full Text Available Abstract Background The aim of this study was to examine the distribution of physical activity facilities by area-level deprivation in Scotland, adjusting for differences in urbanicity, and exploring differences between and within the four largest Scottish cities. Methods We obtained a list of all recreational physical activity facilities in Scotland. These were mapped and assigned to datazones. Poisson and negative binomial regression models were used to investigate associations between the number of physical activity facilities relative to population size and quintile of area-level deprivation. Results The results showed that prior to adjustment for urbanicity, the density of all facilities lessened with increasing deprivation from quintiles 2 to 5. After adjustment for urbanicity and local authority, the effect of deprivation remained significant but the pattern altered, with datazones in quintile 3 having the highest estimated mean density of facilities. Within-city associations were identified between the number of physical activity facilities and area-level deprivation in Aberdeen and Dundee, but not in Edinburgh or Glasgow. Conclusions In conclusion, area-level deprivation appears to have a significant association with the density of physical activity facilities and although overall no clear pattern was observed, affluent areas had fewer publicly owned facilities than more deprived areas but a greater number of privately owned facilities.

Buildings, fields of activity, testing facilities

International Nuclear Information System (INIS)

1974-01-01

Since 1969 the activities of the Materialpruefungsanstalt Stuttgart (MPA) have grown quickly as planned, especially in the field of reactor safety research, which made it necessary to increase the staff to approximately 165 members, to supplement the machines and equipment and to extend the fields of activities occasioning a further departmental reorganization. At present the MPA has the following departments: 1. Teaching (materials testing, materials science and strength of materials) 2. Materials and Welding Technology 3. Materials Science and General Materials Testing with Tribology 4. Design and Strength 5. Creep and Fatigue Testing 6. Central Facilities 7. Vessel and Component Testing. (orig./RW) [de

Fluxes of CH4 and CO2 from soil and termite mounds in south Sudanian savanna of Burkina Faso (West Africa)

Science.gov (United States)

Brümmer, Christian; Papen, Hans; Wassmann, Reiner; Brüggemann, Nicolas

2009-03-01

The contribution of West African savanna ecosystems to global greenhouse gas budgets is highly uncertain. In this study we quantified soil-atmosphere CH4 and CO2 fluxes in the southwest of Burkina Faso from June to September 2005 and from April to September 2006 at four different agricultural fields planted with sorghum (n = 2), cotton, and peanut and at a natural savanna site with termite (Cubitermes fungifaber) mounds. During the rainy season both CH4 uptake and CH4 emission were observed in the savanna, which was on average a CH4 source of 2.79 and 2.28 kg CH4-C ha-1 a-1 in 2005 and 2006, respectively. The crop sites were an average CH4 sink of -0.67 and -0.70 kg CH4-C ha-1 a-1 in the 2 years, without significant seasonal variation. Mean annual soil respiration ranged between 3.86 and 5.82 t CO2-C ha-1 a-1 in the savanna and between 2.50 and 4.51 t CO2-C ha-1 a-1 at the crop sites. CH4 emission from termite mounds was 2 orders of magnitude higher than soil CH4 emissions, whereas termite CO2 emissions were of the same order of magnitude as soil CO2 emissions. Termite CH4 and CO2 release in the savanna contributed 8.8% and 0.4% to the total soil CH4 and CO2 emissions, respectively. At the crop sites, where termite mounds had been almost completely removed because of land use change, termite fluxes were insignificant. Mound density-based upscaling of termite CH4 fluxes resulted in a global termite CH4 source of 0.9 Tg a-1, which corresponds to 0.15% of the total global CH4 budget of 582 Tg a-1, hence significantly lower than those obtained previously by biomass-based calculations. This study emphasizes that land use change, which is of high relevance in this region, has particularly affected soil CH4 fluxes in the past and might still do so in the future.

The hill forts and castle mounds in Lithuania: interaction between geodiversity and human-shaped landscape

Science.gov (United States)

Skridlaite, Grazina; Guobyte, Rimante; Satkunas, Jonas

2015-04-01

Lithuania is famous for its abundant, picturesque hill forts and castle mounds of natural origin. In Lithuania as well as in whole Europe the fortified hills were used as the society dwelling place since the beginning of the Late Bronze Age. Their importance increased when Livonian and Teutonic Orders directed a series of military campaigns against Lithuania with the aim of expansion of Christianity in the region at the end of 1st millennium AD, and they were intensively used till the beginning of the 15th c. when most of them were burned down during fights with the Orders or just abandoned due to the changing political and economical situation. What types of the geodiversity were used for fortified dwellings? The choice in a particular area depended on a variety of geomorphology left behind the retreating ice sheets. High spots dominating their surroundings were of prime interest. In E and SE Lithuania, the Baltic Upland hills marking the eastern margin of the last Weichselian glacier hosted numerous fortified settlements from the end of 2nd millennium BC to the Medieval Ages (Narkunai, Velikuskes etc). In W Lithuania, plateau-like hills of the insular Samogitian Upland had been repeatedly fortified from the beginning of 1st millennium AD to the 14th century (Satrija, Medvegalis etc). Chains of hill forts and castle mounds feature the slopes of glaciofluvial valleys of Nemunas, Neris and other rivers where the slopes were dissected by affluent rivulets and ravines and transformed into isolated, well protected hills (Kernave, Punia, Veliuona etc). Peninsulas and headlands formed by the erosion of fluvial and lacustrine deposits were used in the lowlands, e.g. in central and N Lithuania (Paberze, Mezotne etc). How much the landscape was modified for defense purposes? Long-term erosion and overgrowing vegetation damaged the former fortified sites, however some remains and the archeological excavations allowed their reconstruction. The fortified Bronze Age settlements

DESIGN OF FILL AND FINISH FACILITY FOR ACTIVE PHARMACEUTICAL INGREDIENTS (API)

OpenAIRE

NUUR LAILA KHAIRUDDIN; NORLIZA ABD. RAHMAN; NUR SYAFIQAH KAMARUDIN

2016-01-01

Fill and finish operations continue to be one of the most heavily outsourced activities in the biopharmaceutical manufacturing market today. There are a few aspects that need to be consider in outsource activities like logistic, storage condition, facility certification and audit as regulations and standards which the manufacturer should adhere. Risk would be greater and extra care should be taken when outsource from foreign fill and finish facility. Thus, the internal aseptic fill and fin...

Plutonium working group report on environmental, safety and health vulnerabilities associated with the Department's plutonium storage. Volume II, part 7: Mound working group assessment team report

International Nuclear Information System (INIS)

1994-09-01

This is the report of a visit to the Mound site by the Working Group Assessment Team (WGAT) to assess plutonium vulnerabilities. Purposes of the visit were: to review results of the site's self assessment of current practices for handling and storing plutonium; to conduct an independent assessment of these practices; to reconcile differences and assemble a final list of vulnerabilities; to calculate consequences and probability for each vulnerability; and to issue a report to the Working Group. This report, representing completion of the Mound visit, will be compiled along with those from all other sites with plutonium inventories as part of a final report to the Secretary of Energy

Geology and biology of the "Sticky Grounds," shelf-margin carbonate mounds, and mesophotic ecosystem in the eastern Gulf of Mexico

Science.gov (United States)

Locker, Stanley D.; Reed, John K.; Farrington, Stephanie; Harter, Stacey; Hine, Albert C.; Dunn, Shane

2016-01-01

Shelf-margin carbonate mounds in water depths of 116–135 m in the eastern Gulf of Mexico along the central west Florida shelf were investigated using swath bathymetry, side-scan sonar, sub-bottom imaging, rock dredging, and submersible dives. These enigmatic structures, known to fisherman as the “Sticky Grounds”, trend along slope, are 5–15 m in relief with base diameters of 5–30 m, and suggest widespread potential for mesophotic reef habitat along the west Florida outer continental shelf. Possible origins are sea-level lowstand coral patch reefs, oyster reefs, or perhaps more recent post-lowstand biohermal development. Rock dredging recovered bioeroded carbonate-rock facies comprised of bored and cemented bioclastics. Rock sample components included calcified worm tubes, pelagic sediment, and oysters normally restricted to brackish nearshore areas. Several reef sites were surveyed at the Sticky Grounds during a cruise in August 2010 with the R/V Seward Johnson using the Johnson-Sea-Link II submersible to ground truth the swath-sonar maps and to quantify and characterize the benthic habitats, benthic macrofauna, fish populations, and coral/sponge cover. This study characterizes for the first time this mesophotic reef ecosystem and associated fish populations, and analyzes the interrelationships of the fish assemblages, benthic habitats and invertebrate biota. These highly eroded rock mounds provide extensive hard-bottom habitat for reef invertebrate species as well as essential fish habitat for reef fish and commercially/recreationally important fish species. The extent and significance of associated living resources with these bottom types is particularly important in light of the 2010 Deepwater Horizon oil spill in the northeastern Gulf and the proximity of the Loop Current. Mapping the distribution of these mesophotic-depth ecosystems is important for quantifying essential fish habitat and describing benthic resources. These activities can improve

Decommissioning of nuclear facilities: a growing activity in the world

International Nuclear Information System (INIS)

Anasco, Raul

2001-01-01

Nuclear power plants and nuclear facilities are no different from normal buildings and factories. Eventually, they become worn-out or old fashioned, too expensive to maintain or remodel. Decommissioning a nuclear facility is different from retiring other types because of the radioactivity involved. The most important consideration in nuclear decommissioning is to protect workers and the public from exposure to harmful levels of radiation. General criteria and strategies for the decommissioning of nuclear facilities are described as well as the present decommissioning activities of the Argentine CNEA (author)

Inventory of activation analysis facilities available in the European Community to Industrial users

International Nuclear Information System (INIS)

Pauwels, J.

1975-01-01

This inventory includes lists of activation equipment produced in the European Community, facilities available for industrial users and activation laboratories existing in the European companies. The aim of this inventory is to provide all information that may be useful, to companies interested in activation analysis, as well as to give an idea on existing routine applications and on the European market in facilities

Restoration activities in uranium mining and milling facilities in Spain

International Nuclear Information System (INIS)

Garcia Quiros, J.M.

1997-01-01

From the end of the 80's up to now, several tasks have been carried out in Spain on restoration in the field of uranium mining and milling, significant among them being Andujar Uranium Mill (FUA) closure and La Haba closure. Also, a study has been carried out on restoration of inoperative and abandoned uranium mine sites. At present, detailed plans are being worked out for the project on the closure of the Elefante plant. All activities have been developed in the common framework of national standards and regulations which are generally in compliance with the standards, regulations and recommendations of international organizations. This paper describes briefly the standards and the criteria applied to the restoration tasks at various sites of the uranium mining and milling facilities in Spain. The restoration activities have different characteristics La Haba facility is an isolated and conventional facility to produce uranium concentrate; in the case of old and abandoned uranium mines the intervention criteria is more relevant than the activities to be carried out; the closure (the first phase of licensing) and restoration activities of Elefante plant have to be developed taking into account that it is sited within the area of Quercus plant which is currently in operation. (author)

An examination of recharge mound decay and fossil gradients in arid regional sedimentary basins

International Nuclear Information System (INIS)

Lloyd, J.W.

1980-01-01

In many of the vast arid sedimentary basins of the world, groundwater gradients exist that appear to be anomalous in the context of the probable modern recharge potential. The possibility that such gradients are in fact remnant fossil conditions representing the decay of ancient recharge mounds is examined. An example of decay condition is represented using a resistor-network analogue model in which the time control is based on 14 C ages. The decay hypothesis is found to be plausible with realistic aquifer characteristics but a non-homogeneous flow is indicated from the 14 C data. (author)

Implementation of Enhanced Attenuation at the DOE Mound Site OU-1 Landfill: Accelerating Progress and Reducing Costs

Energy Technology Data Exchange (ETDEWEB)

Hooten, Gwendolyn [U.S. Department of Energy, Office of Legacy Management; Cato, Rebecca [Navarro Research and Engineering; Looney, Brian [Savannah River National Laboratory, Aiken, SC

2016-03-06

At the US Department of Energy (DOE), Office of Legacy Management, Mound, Ohio, Site, chlorinated organic contaminants (cVOCs) originating from the former solid-waste landfill have impacted groundwater in Operable Unit 1 (OU-1). The baseline groundwater remedy was groundwater pump and treat (P&T). Since the source materials have been removed from the landfill, the Mound core team, which consists of DOE, US Environmental Protection Agency (US EPA), Ohio EPA, and other stakeholders, is assessing the feasibility of switching from the active P&T remedy to a passive attenuation-based remedy. Toward this end, an enhanced attenuation (EA) strategy based on the creation of structured geochemical zones was developed. This EA strategy addresses the residual areas of elevated cVOCs in soil and groundwater while minimizing the rebound of groundwater concentrations above regulatory targets (e.g., maximum contaminant levels [MCLs]) and avoiding plume expansion while the P&T system is turned off. The EA strategy has improved confidence and reduced risk on the OU-1 groundwater transition path to monitored natural attenuation (MNA). To better evaluate the EA strategy, DOE is conducting a field demonstration to evaluate the use of edible oils to enhance the natural attenuation processes. The field demonstration is designed to determine whether structured geochemical zones can be established that expedite the attenuation of cVOCs in the OU-1 groundwater. The EA approach at OU-1 was designed based on “structured geochemical zones” and relies on groundwater flow through a succession of anaerobic and aerobic zones. The anaerobic zones stimulate relatively rapid degradation of the original solvent source compounds (e.g., cVOCs such as tetrachloroethene [PCE] and trichloroethene [TCE]). The surrounding aerobic areas encourage relatively rapid degradation of daughter products (such as dichloroethene [DCE] and vinyl chloride [VC]) as well as enhanced cometabolism of TCE resulting from

Release of radioisotopes and activated materials from nuclear installations and facilities

International Nuclear Information System (INIS)

Manfredi, P.F.; Millaud, J. E.

2001-01-01

This report discusses the problems of release of items from facilities and installations where radiation-based activities have been carried out. Several situations are reviewed and their release problems are discussed in detail. Particular attention is devoted to the assessment of the activity of the items to be released. A correct assessment of the activity will help the decision about the final use of the items removed from the radiation-related facility, either re-use, entering the public market, recycling, disposal and storage under different procedures. Even the final destination of the building which hosted the facility needs to be decided on the basis of an accurate assessment of the residual activity. The assessment of the activity, besides being fundamental in guaranteeing a safe approach to the procedures related to the release may result in a substantial profit. This is the case of items whose level of activity is so low that they can be put on the public market, reused or recycled for final product subject to very stringent radiation safety requirements. It will be shown that detector techniques play a fundamental role in the release process. In particular, the low-level counting techniques are fundamental in establishing whether or not the unrestrained release is feasible or not

Stable isotope and 14C study of biogenic calcrete in a termite mound, Western Cape, South Africa, and its palaeoenvironmental significance

Science.gov (United States)

Potts, Alastair J.; Midgley, Jeremy J.; Harris, Chris

2009-09-01

Late Quaternary terrestrial climate records from the semi-arid zone of the Western Cape of South Africa are rare. However, palaeoenvironmental information may be inferred from ancient termite mounds of the region. Calcrete lenses in these mounds have δ 13C and δ 18O values that show systematic changes with radiocarbon dates, which range from 33,629-36,709 to 21,676-23,256 cal yr BP. These dates confirm that these heuweltjies had been present in the landscape since the last glacial period. The decrease in δ 13C and δ 18O from 33,629-36,709 to 21,676-23,256 cal yr BP indicates that climate information is recorded by the calcretes. It is suggested that a progressive decline in air temperature and an increase in moisture availability, and a decline in abundance of C 4 or CAM plants, occurred in the region during the time heuweltjie calcite precipitated.

In vivo neutron activation facility at Brookhaven National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Ma, R.; Yasumura, Seiichi; Dilmanian, F.A.

1997-11-01

Seven important body elements, C, N, Ca, P, K, Na, and Cl, can be measured with great precision and accuracy in the in vivo neutron activation facilities at Brookhaven National Laboratory. The facilities include the delayed-gamma neutron activation, the prompt-gamma neutron activation, and the inelastic neutron scattering systems. In conjunction with measurements of total body water by the tritiated-water dilution method several body compartments can be defined from the contents of these elements, also with high precision. In particular, body fat mass is derived from total body carbon together with total body calcium and nitrogen; body protein mass is derived from total body nitrogen; extracellular fluid volume is derived from total body sodium and chlorine; lean body mass and body cell mass are derived from total body potassium; and, skeletal mass is derived from total body calcium. Thus, we suggest that neutron activation analysis may be valuable for calibrating some of the instruments routinely used in clinical studies of body composition. The instruments that would benefit from absolute calibration against neutron activation analysis are bioelectric impedance analysis, infrared interactance, transmission ultrasound, and dual energy x-ray/photon absorptiometry.

Rubble-mound breakwater armour units displacement analysis by means of digital images processing methods in scale models

OpenAIRE

Courela, J.M.; Carvalho, R.; Lemos, R.; Fortes, C. J. E. M.; Leandro, J.

2015-01-01

Rubble-mound structures are commonly used for coastal and port protection and needs a properly design as well as inspection and maintenance during its lifetime. The design of such breakwaters usually requires a physical scale model to be tested under different irregular incident wave and tide conditions in order to evaluate its hydraulic and structural behaviour, namely the stability of the proposed design. Armour units displacement and fall analysis in physical models are then a ...

Neutron transport calculation for Activation Evaluation for Decommissioning of PET cyclotron Facility

Science.gov (United States)

Nobuhara, Fumiyoshi; Kuroyanagi, Makoto; Masumoto, Kazuyoshi; Nakamura, Hajime; Toyoda, Akihiro; Takahashi, Katsuhiko

2017-09-01

In order to evaluate the state of activation in a cyclotron facility used for the radioisotope production of PET diagnostics, we measured the neutron flux by using gold foils and TLDs. Then, the spatial distribution of neutrons and induced activity inside the cyclotron vault were simulated with the Monte Calro calculation code for neutron transport and DCHAIN-SP for activation calculation. The calculated results are in good agreement with measured values within factor 3. Therefore, the adaption of the advanced evaluation procedure for activation level is proved to be important for the planning of decommissioning of these facilities.

Growth of gas hydrate mounds and gas chimneys of the eastern margin of Japan Sea as revealed by MBES, SSS and SBP of AUV

Science.gov (United States)

Matsumoto, R.; Satoh, M.; Hiromatsu, M.; Tomaru, H.; Machiyama, H.

2010-12-01

A series of PC, ROV and SCS surveys to study the origin and evolution of gas hydrate systems along the eastern margin of Japan Sea have identified a number of shallow GH accumulations on the mounds, 300m to 500m in diameter and 30m to 40m high, on the Umitaka spur and Joetsu knoll in Joetsu basin with the WD of 880m to 1200m (Matsumoto et al., 2005; 2009). All of the hydrate mounds develop on gas chimneys as recognized by seismic profiles, and some are associated with gigantic methane plumes, 600m to 700m high. Multi Beam Echo Sounder (MBES), Side Scan Sonar (SSS) and Sub-Bottom Profiler (SBP) of AUV Urashima have revealed ultra-high resolution topographic features and subsurface structures of the mounds and adjacent areas during the JAMSTEC YK10-08 cruise, July 2010. AUV Urashima ran over the spur and knoll at 50m to 80m above seafloor at a cruising speed of 2.4 knots. MBES and SSS mosaics demonstrate two types of mounds. One is a low swell with smooth surface and weak reflectance, while the other is characterized by rough and uneven topographic features with strong SSS images due to incrustation by methane-induced carbonate concretions and gas hydrates. SBP provides clear stratigraphic and structural relations down to 50mbsf to 80mbsf and recognizes three stratigraphic units as I: upper massive unit (5-10m thick), II: middle evenly bedded unit (15-25m thick) and III: lower slightly bedded unit (> 15-25m thick). Gas chimneys grow up toward the seafloor through Units III, II, and I. When the ceiling of gas chimney stays within Unit III or II, the mound above the chimney is either low swell or nearly flat, while the swell grows up higher when the ceiling reaches to Unit I or the seafloor. Eventually, the ceiling breaks through the seafloor and protrudes to form GH mound up to 40m to 50m high, and then start to decay probably due to mechanical collapse and chemical dissolution of gas hydrates. The ceiling of gas chimneys is often represented by high amplitude, uneven

Pre-title I safety evaluation for the retrieval operations of transuranic waste drums in the Solid Waste Disposal Facility. Revision 2

International Nuclear Information System (INIS)

Rabin, M.S.

1992-08-01

Phase I of the Transuranic (TRU) Waste Facility Line Item Project includes the retrieval and safe storage of the pad drums that are stored on TRU pads 2-6 in the Solid Waste Disposal Facility (SWDF). Drums containing TRU waste were placed on these pads as early as 1974. The pads, once filled, were mounded with soil. The retrieval activities will include the excavation of the soil, retrieval of the pad drums, placing the drums in overpacks (if necessary) and venting and purging the retrieved drums. Once the drums have been vented and purged, they will be transported to other pads within the SWDF or in a designated area until they are eventually treated as necessary for ultimate shipment to the Waste Isolation Pilot Plant in Carlsbad, New Mexico. This safety evaluation provides a bounding assessment of the radiological risk involved with the drum retrieval activities to the maximally exposed offsite individual and the co-located worker. The results of the analysis indicate that the risk to the maximally exposed offsite individual and the co-located worker using maximum frequencies and maximum consequences are within the acceptance criteria defined in WSRC Procedural Manual 9Q. The purpose of this evaluation is to demonstrate the incremental risk from the SWDF due to the retrieval activities for use as design input only. As design information becomes available, this evaluation can be revised to satisfy the safety analysis requirements of DOE Orders 4700 and 5480.23

Reliability Evaluation of a Concrete Crown Wall on a Rubble Mound Breakwater considering Sliding Failure, Overturning and Rupture Failure of the Foundation

DEFF Research Database (Denmark)

Christiani, E.; Sørensen, Jørgen S.; Burcharth, Hans F.

1994-01-01

and rupture failure in the rubble mound are taken into account. The method of probabilistic foundation stability analysis is presented by the example of a translation slip failure involving kinematically correct slip surfaces and failure zones in friction based soil. A conventional static quasi-static...

Maize Storage in Termite Mound Clay, Concrete, and Steel Silos in the Humid Tropics: Comparison and Effect on Bacterial and Fungal Counts

Science.gov (United States)

This study investigated the functional suitability of using the readily-available termite mound clay (TMC) for grain silo construction in comparison to conventional reinforced concrete (RC) and galvanized steel (GS) silos for maize storage in the humid tropics. The extent to which temperature and r...

Pilot-scale reactor activation facility at SRL

International Nuclear Information System (INIS)

Bowman, W.W.

1976-01-01

The Hydrogeocemical and Stream Sediment Reconnaissance portion of the National Uranium Resource Evaluation program requires an analytical technique for uranium and other elements. Based on an automated absolute activation analysis technique using 252 Cf, a pilt-scale facility installed in a production reactor has provided analyses for 2800 samples. Key features include: an automated sample transport system, a delayed neutron detector, two GeLi detectors, a loader, and an unloader, with all components controlled by a microprocessor; a dedicated PDP-9 computer and pulse height analyzer; and correlation and reduction of acquired data by a series of programs using an IBM 360/195 computer. The facility was calibrated with elemental and isotopic standards. Results of analyses of standard reference materials and operational detection limits for typical sediment samples are presented. Plans to increase sample throughput are discussed briefly

A Preliminary Study on Termite Mound Soil as Agricultural Soil for Crop Production in South West, Nigeria

OpenAIRE

Omofunmi, O. E.; Kolo, J. G.; Alli, A. A.; Ojo, A. S.

2017-01-01

It is a popular belief of the people in the Southern region of Nigeria that a land infested with termite usually brings prosperity to the land owner regardless of the type of its usage.  Therefore, the present study assessed termite mounds soil properties which are important to crop production. Two soil samples were collected and their physical and chemical properties determined in accordance with American Public Health Association (APHA, 2005). Data were analyzed using descriptive stati...

MULTICOMPONENT SEISMIC ANALYSIS AND CALIBRATION TO IMPROVE RECOVERY FROM ALGAL MOUNDS: APPLICATION TO THE ROADRUNNER/TOWAOC AREA OF THE PARADOX BASIN, UTE MOUNTAIN UTE RESERVATION, COLORADO

International Nuclear Information System (INIS)

Paul La Pointe; Claudia Rebne; Steve Dobbs

2003-01-01

This report describes the results made in fulfillment of contract DE-FG26-02NT15451, ''Multicomponent Seismic Analysis and Calibration to Improve Recovery from Algal Mounds: Application to the Roadrunner/Towaoc Area of the Paradox Basin, Ute Mountain Ute Reservation, Colorado''. Optimizing development of highly heterogeneous reservoirs where porosity and permeability vary in unpredictable ways due to facies variations can be challenging. An important example of this is in the algal mounds of the Lower and Upper Ismay reservoirs of the Paradox Basin in Utah and Colorado. It is nearly impossible to develop a forward predictive model to delineate regions of better reservoir development, and so enhanced recovery processes must be selected and designed based upon data that can quantitatively or qualitatively distinguish regions of good or bad reservoir permeability and porosity between existing well control. Recent advances in seismic acquisition and processing offer new ways to see smaller features with more confidence, and to characterize the internal structure of reservoirs such as algal mounds. However, these methods have not been tested. This project will acquire cutting edge, three-dimensional, nine-component (3D9C) seismic data and utilize recently-developed processing algorithms, including the mapping of azimuthal velocity changes in amplitude variation with offset, to extract attributes that relate to variations in reservoir permeability and porosity. In order to apply advanced seismic methods a detailed reservoir study is needed to calibrate the seismic data to reservoir permeability, porosity and lithofacies. This will be done by developing a petrological and geological characterization of the mounds from well data; acquiring and processing the 3D9C data; and comparing the two using advanced pattern recognition tools such as neural nets. In addition, should the correlation prove successful, the resulting data will be evaluated from the perspective of

105-DR Large Sodium Fire Facility closure activities evaluation report

International Nuclear Information System (INIS)

Adler, J.G.

1996-01-01

This report evaluates the closure activities at the 105-DR Large Sodium Fire Facility. The closure activities discussed include: the closure activities for the structures, equipment, soil, and gravel scrubber; decontamination methods; materials made available for recycling or reuse; and waste management. The evaluation compares these activities to the regulatory requirements and closure plan requirements. The report concludes that the areas identified in the closure plan can be clean closed

Immobilized low-activity waste interim storage facility, Project W-465 conceptual design report

International Nuclear Information System (INIS)

Pickett, W.W.

1997-01-01

This report outlines the design and Total Estimated Cost to modify the four unused grout vaults for the remote handling and interim storage of immobilized low-activity waste (ILAW). The grout vault facilities in the 200 East Area of the Hanford Site were constructed in the 1980s to support Tank Waste disposal activities. The facilities were to serve project B-714 which was intended to store grouted low-activity waste. The existing 4 unused grout vaults, with modifications for remote handling capability, will provide sufficient capacity for approximately three years of immobilized low activity waste (ILAW) production from the Tank Waste Remediation System-Privatization Vendors (TWRS-PV). These retrofit modifications to the grout vaults will result in an ILAW interim storage facility (Project W465) that will comply with applicable DOE directives, and state and federal regulations

Immobilized low-activity waste interim storage facility, Project W-465 conceptual design report

Energy Technology Data Exchange (ETDEWEB)

Pickett, W.W.

1997-12-30

This report outlines the design and Total Estimated Cost to modify the four unused grout vaults for the remote handling and interim storage of immobilized low-activity waste (ILAW). The grout vault facilities in the 200 East Area of the Hanford Site were constructed in the 1980s to support Tank Waste disposal activities. The facilities were to serve project B-714 which was intended to store grouted low-activity waste. The existing 4 unused grout vaults, with modifications for remote handling capability, will provide sufficient capacity for approximately three years of immobilized low activity waste (ILAW) production from the Tank Waste Remediation System-Privatization Vendors (TWRS-PV). These retrofit modifications to the grout vaults will result in an ILAW interim storage facility (Project W465) that will comply with applicable DOE directives, and state and federal regulations.

Total body-calcium measurements: comparison of two delayed-gamma neutron activation facilities

International Nuclear Information System (INIS)

Ma, R.; Ellis, K.J.; Shypailo, R.J.; Pierson, R.N. Jr.

1999-01-01

This study compares two independently calibrated delayed-gamma neutron activation (DGNA) facilities, one at the Brookhaven National Laboratory (BNL), Upton, New York, and the other at the Children's Nutrition Research Center (CNRC), Houston, Texas that measure total body calcium (TBCa). A set of BNL phantoms was sent to CNRC for neutron activation analysis, and a set of CNRC phantoms was measured at BNL. Both facilities showed high precision (<2%), and the results were in good agreement, within 5%. (author)

A novel use of LIMS for surveillance activities at the Savannah River Site

International Nuclear Information System (INIS)

Rogier, W.J.

2000-01-01

The current mission of the Savannah River Site is focused primarily on cleanup and disposal of waste associated with more than 40 years of nuclear material production. However, SRS continues to provide tritium processing for the Department of Energy. Tritium, a radioactive isotope of hydrogen gas, is used to boost the explosive power of nuclear weapons. The tritium container, processed by SRS, is known as a reservoir. Part of the SRS tritium mission is to assure the safety and reliability of tritium reservoirs by conducting a series of thorough surveillance tests on a sampling of fielded reservoirs. Data from these tests have historically been stored in a database archive and reporting system known as QUADSTAR. This system was developed at the Mound Facility in the mid-1980s when Mound performed the reservoir surveillance mission for DOE. The surveillance mission and the QUADSTAR database were transferred to SRS during the downsizing of the Nuclear Weapon Complex in the mid-1990s

Automatic Modelling of Rubble Mound Breakwaters from LIDAR Data

Science.gov (United States)

Bueno, M.; Díaz-Vilariño, L.; González-Jorge, H.; Martínez-Sánchez, J.; Arias, P.

2015-08-01

Rubble mound breakwaters maintenance is critical to the protection of beaches and ports. LiDAR systems provide accurate point clouds from the emerged part of the structure that can be modelled to make it more useful and easy to handle. This work introduces a methodology for the automatic modelling of breakwaters with armour units of cube shape. The algorithm is divided in three main steps: normal vector computation, plane segmentation, and cube reconstruction. Plane segmentation uses the normal orientation of the points and the edge length of the cube. Cube reconstruction uses the intersection of three perpendicular planes and the edge length. Three point clouds cropped from the main point cloud of the structure are used for the tests. The number of cubes detected is around 56 % for two of the point clouds and 32 % for the third one over the total physical cubes. Accuracy assessment is done by comparison with manually drawn cubes calculating the differences between the vertexes. It ranges between 6.4 cm and 15 cm. Computing time ranges between 578.5 s and 8018.2 s. The computing time increases with the number of cubes and the requirements of collision detection.

Monsanto Mound Laboratory tritium waste control technology development program

International Nuclear Information System (INIS)

Bixel, J.C.; Kershner, C.J.; Rhinehammer, T.B.

1975-01-01

Over the past four years, implementation of tritium waste control programs has resulted in a 30-fold reduction in the gaseous tritium effluents from Mound Laboratory. However, to reduce tritium waste levels to the ''as low as practicable'' guideline poses problems that are beyond ready solution with state-of-the-art tritium control technology. To meet this advanced technology need, a tritium waste control technology program was initiated. Although the initial thrust of the work under this program was oriented toward development of gaseous effluent treatment systems, its natural evolution has been toward the liquid waste problem. It is thought that, of all the possible approaches to disposal of tritiated liquid wastes, recovery offers the greatest advantages. End products of the recovery processes would be water detritiated to a level below the Radioactivity Concentration Guide (RCG) or detritiated to a level that would permit safe recycle in a closed loop operation and enriched tritium. The detritiated water effluent could be either recycled in a closed loop operation such as in a fuel reprocessing plant or safely released to the biosphere, and the recovered tritium could be recycled for use in fusion reactor studies or other applications

The Remote Handled Immobilization Low Activity Waste Disposal Facility Environmental Permits & Approval Plan

Energy Technology Data Exchange (ETDEWEB)

DEFFENBAUGH, M.L.

2000-08-01

The purpose of this document is to revise Document HNF-SD-ENV-EE-003, ''Permitting Plan for the Immobilized Low-Activity Waste Project, which was submitted on September 4, 1997. That plan accounted for the interim storage and disposal of Immobilized-Low Activity Waste at the existing Grout Treatment Facility Vaults (Project W-465) and within a newly constructed facility (Project W-520). Project W-520 was to have contained a combination of concrete vaults and trenches. This document supersedes that plan because of two subsequent items: (1) A disposal authorization that was received on October 25, 1999, in a U. S. Department of Energy-Headquarters, memorandum, ''Disposal Authorization Statement for the Department of Energy Hanford site Low-Level Waste Disposal facilities'' and (2) ''Breakthrough Initiative Immobilized Low-Activity Waste (ILAW) Disposal Alternative,'' August 1999, from Lucas Incorporated, Richland, Washington. The direction within the U. S. Department of Energy-Headquarters memorandum was given as follows: ''The DOE Radioactive Waste Management Order requires that a Disposal authorization statement be obtained prior to construction of new low-level waste disposal facility. Field elements with the existing low-level waste disposal facilities shall obtain a disposal authorization statement in accordance with the schedule in the complex-wide Low-Level Waste Management Program Plan. The disposal authorization statement shall be issued based on a review of the facility's performance assessment and composite analysis or appropriate CERCLA documentation. The disposal authorization shall specify the limits and conditions on construction, design, operations, and closure of the low-level waste facility based on these reviews. A disposal authorization statement is a part of the required radioactive waste management basis for a disposal facility. Failure to obtain a disposal authorization statement

Correlates of distances traveled to use recreational facilities for physical activity behaviors

Directory of Open Access Journals (Sweden)

Bulsara Max

2006-07-01

Full Text Available Abstract Background Information regarding how far people are willing to travel to use destinations for different types of recreational physical activity behaviors is limited. This study examines the demographic characteristics, neighborhood opportunity and specific-physical activity behaviors associated with distances traveled to destinations used for recreational physical activity. Methods A secondary analysis was undertaken of data (n = 1006 from a survey of Western Australian adults. Road network distances between respondents' homes and 1 formal recreational facilities; 2 beaches and rivers; and 3 parks and ovals used for physical activity were determined. Associations between distances to destinations and demographic characteristics, neighborhood opportunity (number of destinations within 1600 meters of household, and physical activity behaviors were examined. Results Overall, 56.3% of respondents had used a formal recreational facility, 39.9% a beach or river, and 38.7% a park or oval. The mean distance traveled to all destinations used for physical activity was 5463 ± 5232 meters (m. Distances traveled to formal recreational facilities, beaches and rivers, and parks and ovals differed depending on the physical activity undertaken. Younger adults traveled further than older adults (7311.8 vs. 6012.6 m, p = 0.03 to use beaches and rivers as did residents of socio-economically disadvantaged areas compared with those in advantaged areas (8118.0 vs. 7311.8 m, p = 0.02. Club members traveled further than non-members to use parks and ovals (4156.3 vs. 3351.6 meters, p = 0.02. The type of physical activity undertaken at a destination and number of neighborhood opportunities were also associated with distance traveled for all destination types. Conclusion The distances adults travel to a recreational facility depends on the demographic characteristics, destination type, physical activity behavior undertaken at that destination, and number of

A new facility for rapid neutron activation analysis

International Nuclear Information System (INIS)

Zeisler, R.; Makarewicz, M.; Grass, F.; Casta, J.

1996-01-01

Many research groups have undertaken efforts on the utilization of short-lived nuclides in a broad spectrum of neutron activation analysis (NAA) applications. The advantages of these approaches are obvious because the information on the sample can be extracted more rapidly. In addition to its other advantages, NAA can become extremely competitive in price and analysis time. Nevertheless, NAA with short-lived nuclides has not gained broad popularity, perhaps because of some difficulties in accuracy and the availability of suitable irradiation facilities. This report discusses the ASTRA reactor for neutron activation analysis capabilities

Nuclear Rocket Facility Decommissioning Project: Controlled Explosive Demolition of Neutron-Activated Shield Wall

International Nuclear Information System (INIS)

Michael R. Kruzic

2007-01-01

Located in Area 25 of the Nevada Test Site (NTS), the Test Cell A (TCA) Facility was used in the early to mid-1960s for the testing of nuclear rocket engines, as part of the Nuclear Rocket Development Program, to further space travel. Nuclear rocket testing resulted in the activation of materials around the reactors and the release of fission products and fuel particles in the immediate area. Identified as Corrective Action Unit 115, the TCA facility was decontaminated and decommissioned (D and D) from December 2004 to July 2005 using the Streamlined Approach for Environmental Restoration (SAFER) process, under the ''Federal Facility Agreement and Consent Order''. The SAFER process allows environmental remediation and facility closure activities (i.e., decommissioning) to occur simultaneously provided technical decisions are made by an experienced decision maker within the site conceptual site model, identified in the Data Quality Objective process. Facility closure involved a seven-step decommissioning strategy. Key lessons learned from the project included: (1) Targeted preliminary investigation activities provided a more solid technical approach, reduced surprises and scope creep, and made the working environment safer for the D and D worker. (2) Early identification of risks and uncertainties provided opportunities for risk management and mitigation planning to address challenges and unanticipated conditions. (3) Team reviews provided an excellent mechanism to consider all aspects of the task, integrated safety into activity performance, increase team unity and ''buy-in'' and promoted innovative and time saving ideas. (4) Development of CED protocols ensured safety and control. (5) The same proven D and D strategy is now being employed on the larger ''sister'' facility, Test Cell C

The Remote Handled Immobilization Low-Activity Waste Disposal Facility Environmental Permits and Approval Plan

International Nuclear Information System (INIS)

DEFFENBAUGH, M.L.

2000-01-01

The purpose of this document is to revise Document HNF-SD-ENV-EE-003, ''Permitting Plan for the Immobilized Low-Activity Waste Project, which was submitted on September 4, 1997. That plan accounted for the interim storage and disposal of Immobilized-Low Activity Waste at the existing Grout Treatment Facility Vaults (Project W-465) and within a newly constructed facility (Project W-520). Project W-520 was to have contained a combination of concrete vaults and trenches. This document supersedes that plan because of two subsequent items: (1) A disposal authorization that was received on October 25, 1999, in a U. S. Department of Energy-Headquarters, memorandum, ''Disposal Authorization Statement for the Department of Energy Hanford site Low-Level Waste Disposal facilities'' and (2) ''Breakthrough Initiative Immobilized Low-Activity Waste (ILAW) Disposal Alternative,'' August 1999, from Lucas Incorporated, Richland, Washington. The direction within the U. S. Department of Energy-Headquarters memorandum was given as follows: ''The DOE Radioactive Waste Management Order requires that a Disposal authorization statement be obtained prior to construction of new low-level waste disposal facility. Field elements with the existing low-level waste disposal facilities shall obtain a disposal authorization statement in accordance with the schedule in the complex-wide Low-Level Waste Management Program Plan. The disposal authorization statement shall be issued based on a review of the facility's performance assessment and composite analysis or appropriate CERCLA documentation. The disposal authorization shall specify the limits and conditions on construction, design, operations, and closure of the low-level waste facility based on these reviews. A disposal authorization statement is a part of the required radioactive waste management basis for a disposal facility. Failure to obtain a disposal authorization statement or record of decision shall result in shutdown of an operational

IAEA safety requirements for safety assessment of fuel cycle facilities and activities

International Nuclear Information System (INIS)

Jones, G.

2013-01-01

The IAEA's Statute authorises the Agency to establish standards of safety for protection of health and minimisation of danger to life and property. In that respect, the IAEA has established a Safety Fundamentals publication which contains ten safety principles for ensuring the protection of workers, the public and the environment from the harmful effects of ionising radiation. A number of these principles require safety assessments to be carried out as a means of evaluating compliance with safety requirements for all nuclear facilities and activities and to determine the measures that need to be taken to ensure safety. The safety assessments are required to be carried out and documented by the organisation responsible for operating the facility or conducting the activity, are to be independently verified and are to be submitted to the regulatory body as part of the licensing or authorisation process. In addition to the principles of the Safety Fundamentals, the IAEA establishes requirements that must be met to ensure the protection of people and the environment and which are governed by the principles in the Safety Fundamentals. The IAEA's Safety Requirements publication 'Safety Assessment for Facilities and Activities', establishes the safety requirements that need to be fulfilled in conducting and maintaining safety assessments for the lifetime of facilities and activities, with specific attention to defence in depth and the requirement for a graded approach to the application of these safety requirements across the wide range of fuel cycle facilities and activities. Requirements for independent verification of the safety assessment that needs to be carried out by the operating organisation, including the requirement for the safety assessment to be periodically reviewed and updated are also covered. For many fuel cycle facilities and activities, environmental impact assessments and non-radiological risk assessments will be required. The

OCORRÊNCIA DE ESPÉCIES DE CUPINS DE MONTÍCULO EM PASTAGENS NO ESTADO DE GOIÁS THE OCCURRENCE OF MOUND-BUILDING TERMITE SPECIES IN PASTURES, IN GOIÁS, BRAZIL

Directory of Open Access Journals (Sweden)

Edinon Aguiar de Araújo

2007-09-01

Full Text Available

Este trabalho teve por objetivo identificar as espécies e as áreas ocupadas por cupins de montículos nas pastagens, visando estabelecer estratégias de controle para cada região do Estado de Goiás. Foram realizados levantamentos em 133 municípios que apresentaram, em média, 72,68 cupinzeiros/ha, com um diâmetro médio de 83,02 cm. Foram identificados dezenove gêneros do inseto, sendo 58% das amostras representadas por Cornitermes snyderi, 13,85% por C. cumulans, 6,35% por Procornitermes araujoi, 3,77% por espécies do gênero Syntermes e o restante (15,74% por outras espécies de menor importância.

PALAVRAS-CHAVE: Insecta; cupins; distribuição; pastagens.

This study had the purpose of identifying species and occurrence areas of mound termites in Goiás, Brazil, in order to establish control strategies. The survey was done in 133 municipalities evaluating the number of mounds/ha and mean diameter of mounds. We found an average of 72.68 mound/ha with a mean diameter of 83.02 cm. Nineteen insect genera were identified. Of these, 58% were identified as Cornitermes snyderi, 13.85% as C. cumulans, 6.35% as Procornitermes araujoi, 3.77% as species of Syntermes, and 15.74% were considered of minor importance.

KEY-WORDS: Insecta; termites; distribution; pastures.

Research and development activities of a neutron generator facility

International Nuclear Information System (INIS)

Darsono Sudjatmoko; Pramudita Anggraita; Sukarman Aminjoyo

2000-01-01

The neutron generator facility at YNRC is used for elemental analysis, nuclear data measurement and education. In nuclear data measurement the focus is on re-evaluating the existing scattered nuclear activation cross-section to obtain systematic data for nuclear reactions such as (n,p), (n,α), and (n,2n). In elemental analysis it is used for analyzing the Nitrogen (N), Phosphor (P) and Potassium (K) contents in chemical and natural fertilizers (compost), protein in rice, soybean, and corn and pollution level in rivers. The neutron generator is also used for education and training of BATAN staff and university students. The facility can also produce neutron generator components. (author)

Department of Defense Facilities Sustainment, Restoration, & Modernization Program Plan

Science.gov (United States)

2009-05-15

09 Jul-09 Sep-09 Jan-11 1639 Fort Shafter HI Structural Termite Repairs, Palm Circle B102 $2,750 O 38431 Jul-09 Sep-09 Oct-09 Dec-09 Apr-11 1640...09 Dec-10 1891 Detroit Arsenal MI Mound Rd Improvements at Mound Rd Access Control Point $380 P 35285 May-09 Jul-09 Aug-09 Oct-09 Feb-11 1892...VLSB090070 N/A N/A Jul-09 Aug-09 Aug-10 1526 Shaw AFB SC Repr Termite /Structural Damage Family Housing $500 F VLSB090071 N/A N/A Jul-09 Aug-09 Apr-10 1527

Mortality among workers exposed to external ionizing radiation at a nuclear facility in Ohio

International Nuclear Information System (INIS)

Wiggs, L.D.; Cox-DeVore, C.A.; Wilkinson, G.S.; Reyes, M.

1991-01-01

In a cohort mortality study of white men employed by the Mound Facility (1947 through 1979), observed deaths did not exceed those expected based on US death rates for the overall cohort or for the subcohort monitored for external ionizing radiation. Among the radiation-monitored subcohort, mortality for workers with cumulative radiation doses of at least 10 mSv was not significantly increased when compared with mortality for coworkers with cumulative doses of less than 10 mSv. A significant dose-response based on a Mantel-Haenszel test of trend was observed for all leukemias. However, when a death from chronic lymphatic leukemia, a type of leukemia generally not regarded as radiogenic, was removed from the analyses, the strength of the dose-response was reduced

Bioaerosol releases from compost facilities: Evaluating passive and active source terms at a green waste facility for improved risk assessments

Science.gov (United States)

Taha, M. P. M.; Drew, G. H.; Longhurst, P. J.; Smith, R.; Pollard, S. J. T.

The passive and active release of bioaerosols during green waste composting, measured at source is reported for a commercial composting facility in South East (SE) England as part of a research programme focused on improving risk assessments at composting facilities. Aspergillus fumigatus and actinomycetes concentrations of 9.8-36.8×10 6 and 18.9-36.0×10 6 cfu m -3, respectively, measured during the active turning of green waste compost, were typically 3-log higher than previously reported concentrations from static compost windrows. Source depletion curves constructed for A. fumigatus during compost turning and modelled using SCREEN3 suggest that bioaerosol concentrations could reduce to background concentrations of 10 3 cfu m -3 within 100 m of this site. Authentic source term data produced from this study will help to refine the risk assessment methodologies that support improved permitting of compost facilities.

Stanford Synchrotron Radiation Laboratory 1991 activity report. Facility developments January 1991--March 1992

International Nuclear Information System (INIS)

Cantwell, K.; St. Pierre, M.

1992-01-01

SSRL is a national facility supported primarily by the Department of Energy for the utilization of synchrotron radiation for basic and applied research in the natural sciences and engineering. It is a user-oriented facility which welcomes proposals for experiments from all researchers. The synchrotron radiation is produced by the 3.5 GeV storage ring, SPEAR, located at the Stanford Linear Accelerator Center (SLAC). SPEAR is a fully dedicated synchrotron radiation facility which operates for user experiments 7 to 9 months per year. SSRL currently has 24 experimental stations on the SPEAR storage ring. There are 145 active proposals for experimental work from 81 institutions involving approximately 500 scientists. There is normally no charge for use of beam time by experimenters. This report summarizes the activity at SSRL for the period January 1, 1991 to December 31, 1991 for research. Facility development through March 1992 is included

Stanford Synchrotron Radiation Laboratory 1991 activity report. Facility developments January 1991--March 1992

Energy Technology Data Exchange (ETDEWEB)

Cantwell, K.; St. Pierre, M. [eds.

1992-12-31

SSRL is a national facility supported primarily by the Department of Energy for the utilization of synchrotron radiation for basic and applied research in the natural sciences and engineering. It is a user-oriented facility which welcomes proposals for experiments from all researchers. The synchrotron radiation is produced by the 3.5 GeV storage ring, SPEAR, located at the Stanford Linear Accelerator Center (SLAC). SPEAR is a fully dedicated synchrotron radiation facility which operates for user experiments 7 to 9 months per year. SSRL currently has 24 experimental stations on the SPEAR storage ring. There are 145 active proposals for experimental work from 81 institutions involving approximately 500 scientists. There is normally no charge for use of beam time by experimenters. This report summarizes the activity at SSRL for the period January 1, 1991 to December 31, 1991 for research. Facility development through March 1992 is included.

NIREX transport activities since rejection of the rock characterisation facility planning application

International Nuclear Information System (INIS)

Barlow, S.; Carr, N.; Sievwright, R.W.T.

2000-01-01

The application by Nirex to build an underground Rock Characterisation Facility, was rejected by the Secretary of State on 17 March 1997. This decision has caused Nirex to reconsider its forward programme for the development of an underground disposal facility for intermediate level waste. This paper describes the transport related activities being undertaken by Nirex since that date. (author)

Summary of the last step of active test at separation facility and purification facility in Rokkasho Reprocessing Plant

International Nuclear Information System (INIS)

Kuroishi, Yuuki; Iseki, Tadahiro; Mitani, Akira; Takahashi, Naoki; Tsujimura, Akino; Sato, Nobuharu; Inaba, Makoto; Itagaki, Takashi

2008-01-01

During the last step of Active Test (AT) at Rokkasho Reprocessing Plant (RRP), the performance of the Separation Facility, mainly for pulsed columns and mixer-settlers were tested; Diluent washing efficiency, Plutonium extraction and stripping efficiency, Decontamination factors of fission products and Uranium and plutonium losses into wastes. Also, those of the Plutonium purification unit in the Purification Facility have been checked; Diluent washing efficiency, Plutonium extraction and stripping efficiency and Plutonium losses into wastes. Test results were equivalent to or better than expected values. (author)

Wave Overtopping over Crown Walls and Run-up on Rubble Mound Breakwaters with Kolos Armour under Random Waves

OpenAIRE

A. Arunjith; S.A. Sannasiraj; V. Sundar

2013-01-01

The design of rubble mound structures like breakwaters and seawalls are influenced by the wave run-up and overtopping over them. The above phenomena largely depend on the type of the armour units as they directly interact with the incident waves. The hydrodynamic characteristics of various concrete armour units have been established by several researchers. A new armour block, ‘Kolos’, a modified version of Dolos, is considered in this study for a detailed investigation. An attempt is made to ...

Flow and Turbulence at Rubble-Mound Breakwater Armor Layers under Solitary Wave

DEFF Research Database (Denmark)

Jensen, Bjarne; Christensen, Erik Damgaard; Sumer, B. Mutlu

2015-01-01

This paper presents the results of an experimental investigation of the flow and turbulence at the armor layer of rubble-mound breakwaters during wave action. The study focused on the details of the flow and turbulence in the armor layer and on the effect of the porous core on flow and stability....... To isolate the processes involved with the flow in the porous core, experiments were conducted with increasing complexity. Specifically, three parallel experiments were performed including (1) an impermeable smooth breakwater slope, (2) an impermeable breakwater slope with large roughness elements added...... to the breakwater, and (3) a porous breakwater where the porous core was added below the breakwater front. One breakwater slope of 1:1.5 was applied. In this paper the focus is on the details of a single sequence of wave approach, run-up, and rundown. To isolate this sequence the experiments were performed applying...

Safety assessment of outdoor live fire range

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-05-01

The following Safety Assessment (SA) pertains to the outdoor live fire range facility (LFR). The purpose of this facility is to supplement the indoor LFR. In particular it provides capacity for exercises that would be inappropriate on the indoor range. This SA examines the risks that are attendant to the training on the outdoor LFR. The outdoor LFR used by EG&G Mound is privately owned. It is identified as the Miami Valley Shooting Grounds. Mondays are leased for the exclusive use of EG&G Mound.

Tritium emissions reduction facility (TERF)

International Nuclear Information System (INIS)

Lamberger, P.H.; Hedley, W.H.

1993-01-01

Tritium handling operations at Mound include production of tritium-containing devices, evaluation of the stability of tritium devices, tritium recovery and enrichment, tritium process development, and research. In doing this work, gaseous process effluents containing 400,000 to 1,000,000 curies per year of tritium are generated. These gases must be decontaminated before they can be discharged to the atmosphere. They contain tritium as elemental hydrogen, as tritium oxide, and as tritium-containing organic compounds at low concentrations (typically near one ppm). The rate at which these gases is generated is highly variable. Some tritium-containing gas is generated at all times. The systems used at Mound for capturing tritium from process effluents have always been based on the open-quotes oxidize and dryclose quotes concept. They have had the ability to remove tritium, regardless of the form it was in. The current system, with a capacity of 1.0 cubic meter of gas per minute, can effectively remove tritium down to part-per-billion levels

Multicomponent Seismic Analysis and Calibration to Improve Recovery from Algal Mounds: Application to the Roadrunner/Towaoc area of the Paradox Basin, UTE Mountain UTE Reservation, Colorado

International Nuclear Information System (INIS)

Joe Hachey

2007-01-01

The goals of this project were: (1) To enhance recovery of oil contained within algal mounds on the Ute Mountain Ute tribal lands. (2) To promote the use of advanced technology and expand the technical capability of the Native American Oil production corporations by direct assistance in the current project and dissemination of technology to other Tribes. (3) To develop an understanding of multicomponent seismic data as it relates to the variations in permeability and porosity of algal mounds, as well as lateral facies variations, for use in both reservoir development and exploration. (4) To identify any undiscovered algal mounds for field-extension within the area of seismic coverage. (5) To evaluate the potential for applying CO 2 floods, steam floods, water floods or other secondary or tertiary recovery processes to increase production. The technical work scope was carried out by: (1) Acquiring multicomponent seismic data over the project area; (2) Processing and reprocessing the multicomponent data to extract as much geological and engineering data as possible within the budget and time-frame of the project; (3) Preparing maps and data volumes of geological and engineering data based on the multicomponent seismic and well data; (4) Selecting drilling targets if warranted by the seismic interpretation; (5) Constructing a static reservoir model of the project area; and (6) Constructing a dynamic history-matched simulation model from the static model. The original project scope covered a 6 mi 2 (15.6 km 2 ) area encompassing two algal mound fields (Towaoc and Roadrunner). 3D3C seismic data was to acquired over this area to delineate mound complexes and image internal reservoir properties such as porosity and fluid saturations. After the project began, the Red Willow Production Company, a project partner and fully-owned company of the Southern Ute Tribe, contributed additional money to upgrade the survey to a nine-component (3D9C) survey. The purpose of this upgrade

Multicomponent Seismic Analysis and Calibration to Improve Recovery from Algal Mounds: Application to the Roadrunner/Towaoc area of the Paradox Basin, UTE Mountain UTE Reservation, Colorado

Energy Technology Data Exchange (ETDEWEB)

Joe Hachey

2007-09-30

The goals of this project were: (1) To enhance recovery of oil contained within algal mounds on the Ute Mountain Ute tribal lands. (2) To promote the use of advanced technology and expand the technical capability of the Native American Oil production corporations by direct assistance in the current project and dissemination of technology to other Tribes. (3) To develop an understanding of multicomponent seismic data as it relates to the variations in permeability and porosity of algal mounds, as well as lateral facies variations, for use in both reservoir development and exploration. (4) To identify any undiscovered algal mounds for field-extension within the area of seismic coverage. (5) To evaluate the potential for applying CO{sub 2} floods, steam floods, water floods or other secondary or tertiary recovery processes to increase production. The technical work scope was carried out by: (1) Acquiring multicomponent seismic data over the project area; (2) Processing and reprocessing the multicomponent data to extract as much geological and engineering data as possible within the budget and time-frame of the project; (3) Preparing maps and data volumes of geological and engineering data based on the multicomponent seismic and well data; (4) Selecting drilling targets if warranted by the seismic interpretation; (5) Constructing a static reservoir model of the project area; and (6) Constructing a dynamic history-matched simulation model from the static model. The original project scope covered a 6 mi{sup 2} (15.6 km{sup 2}) area encompassing two algal mound fields (Towaoc and Roadrunner). 3D3C seismic data was to acquired over this area to delineate mound complexes and image internal reservoir properties such as porosity and fluid saturations. After the project began, the Red Willow Production Company, a project partner and fully-owned company of the Southern Ute Tribe, contributed additional money to upgrade the survey to a nine-component (3D9C) survey. The purpose

Compilation of historical information of 300 Area facilities and activities

International Nuclear Information System (INIS)

Gerber, M.S.

1992-12-01

This document is a compilation of historical information of the 300 Area activities and facilities since the beginning. The 300 Area is shown as it looked in 1945, and also a more recent (1985) look at the 300 Area is provided

Compilation of historical information of 300 Area facilities and activities

Energy Technology Data Exchange (ETDEWEB)

Gerber, M.S.

1992-12-01

This document is a compilation of historical information of the 300 Area activities and facilities since the beginning. The 300 Area is shown as it looked in 1945, and also a more recent (1985) look at the 300 Area is provided.

Restoration of Lighthouse Facilities and their Valorisation through Commercial Activities

Directory of Open Access Journals (Sweden)

Mate Perišić

2010-07-01

Full Text Available There have not been many studies on the role of lighthouses throughout history. Since the lighthouse has become a prototypical example of a good market solution for the public goods problem, there is a high demand for these studies. The authors develop a concept of study in which the problem of lighthouse maintenance becomes a business problem by including restored lighthouse facilities in the tourist offer. They justify this kind of approach with concrete examples of valorising lighthouse facilities through commercial activities. In the period of globalization and that of striving for constant economic development and product optimization, lighthouses are becoming an inevitable part of the tourist offer of the Republic of Croatia. The restoration and commercialization of lighthouse facilities are very important in gaining a competitive advantage over other tourist destinations in Europe.

Utilization and facility of neutron activation analysis in HANARO research reactor

International Nuclear Information System (INIS)

Chung, Y.S.; Chung, Y.J.; Moon, J.H.

1998-01-01

The facilities of neutron activation analysis within a multi-purpose research reactor (HANARO) are described and the main applications of Neutron activation analysis (NAA) in Korea are reviewed. The sample irradiation tube, automatic and manual pneumatic transfer system, are installed at three irradiation holes. One irradiation hole is lined with a cadmium tube for epithermal-nal NAA. The performance of the NAA facility was examined to identify the characteristics of tube transfer system, irradiation sites and polyethylene irradiation capsule. The available thermal neutron flux with each irradiation site are in the range of 3.9x10 13 -1.6x10 14 n/cm 2 ·s and cadmium ratios are 15-250. Neutron activation analysis has been applied in the trace component analysis of nuclear, geological, biological, environmental and high purity materials and various polymers for research and development. Analytical services and the latest analytical results are summarized. (author)

Development of tritium technology for the United States magnetic fusion energy program

International Nuclear Information System (INIS)

Anderson, J.L.; Wilkes, W.R.

1980-01-01

Tritium technology development for the DOE fusion program is taking place principally at three laboratories, Mound Facility, Argonne National Laboratory and the Los Alamos Scientific Laboratory. This paper will review the major aspects of each of the three programs and look at aspects of the tritium technology being developed at other laboratories within the United States. Facilities and experiments to be discussed include the Tritium Effluent Control Laboratory and the Tritium Storage and Delivery System for the Tokamak Fusion Test Reactor at Mound Facility; the Lithium Processing Test Loop and the solid breeder blanket studies at Argonne; and the Tritium Systems Test Assembly at Los Alamos

The upgrading of the cyclic neutron activation analysis facility at the Dalat research reactor

International Nuclear Information System (INIS)

Van Doanh Ho; Manh Dung Ho; Quang Thien Tran; Dong Vu Cao; Thanh Viet Ha

2018-01-01

The cyclic neutron activation analysis (CNAA) facility based on a pneumatic transfer system for short irradiation and rapid counting has recently been upgraded at the Dalat research reactor. The original facility was only designed for single irradiation. Therefore, this work has aimed to upgrade both hardware and software for the cyclic irradiation. In this paper, the upgrading of the facility for CNAA was described. Irradiation time of the facility were calibrated, thereby reducing irradiation time to seconds with precision. The accuracy and sensitivity of CNAA based-on the upgraded facility were assessed by determination of some short-lived nuclides. (author)

CHANGE OF CONTRACTOR FOR THE FACILITIES MANAGEMENT ACTIVITIES AT CERN

CERN Document Server

2003-01-01

The Facilities Management contract at CERN, under the responsibility of ST Division, Group FM, is in charge of the maintenance and minor works on tertiary installations (i.e. all structures and installations that have no direct relation to the running of the accelerators) for the following trades: - Technical: heating, ventilation, air conditioning, plumbing, electricity, civil engineering (painting, roofing, glazing, blinds, fencing, masonry etc.), cleansing, passenger and goods lifts, automatic and powered doors, kitchen equipment, roads, signs, keys and locks, office furniture, - Services: waste collection, security, green areas, cleaning and sanitary supplies, disinfection, rodent control and insect control. Starting from the 1st June the present contractor will stop some activities that will be taken under its responsibility by the new one, INGEST Facility. Others activities will be moved on the 1st July. Minor perturbation in the service might occur. The contact number will not change and will be opera...

CHANGE OF CONTRACTOR FOR THE FACILITIES MANAGEMENT ACTIVITIES AT CERN

CERN Document Server

2003-01-01

The Facilities Management contract at CERN, under the responsibility of ST Division, Group FM, is in charge of the maintenance and minor works on tertiary installations (i.e. all structures and installations that have no direct relation to the running of the accelerators) for the following trades: - Technical: heating, ventilation, air conditioning, plumbing, electricity, civil engineering (painting, roofing, glazing, blinds, fencing, masonry etc.), cleansing, passenger and goods lifts, automatic and powered doors, kitchen equipment, roads, signs, keys and locks, office furniture, - Services: waste collection, security, green areas, cleaning and sanitary supplies, disinfection, rodent control and insect control. Starting from the 1st June the present contractor will stop some activities that will be taken under its responsibility by the new one, INGEST Facility. The remaining activities (including cleaning) will be moved on the 1st July. Minor perturbation in the service might occur. The contact number will ...

Sorptive removal of arsenate using termite mound.

Science.gov (United States)

Fufa, Fekadu; Alemayehu, Esayas; Lennartz, Bernd

2014-01-01

Long-term consumption of arsenic results in severe and permanent health damages. The aim of the study was to investigate arsenate (As(V)) sorption capacity of termite mound (TM), containing mainly silicon, aluminum, iron and titanium oxides, under batch adsorption setup. The pattern of As(V) removal with varying contact time, solution pH, adsorbent dose, As(V) concentration and competing anions was investigated. Dissolution of the adsorbent was insignificant under the equilibrium conditions. Equilibrium was achieved within 40 min of agitation time. Kinetic data of As(V) adsorption followed well the pseudo-second order equation (R(2) > 0.99). High As(V) removal efficiency (∼ 99%) was observed over a pH range ∼ 3-∼ 10, which is of great importance in the practical application. The Freundlich and Dubinin-Radushkevich isotherms well described (R(2) > 0.99, χ(2) ∼ 0.05) the equilibrium As(V) adsorption, giving a coefficient of adsorption 1.48 mg(1-1/n)L(1/n)/g and a saturation capacity 13.50 mg/g respectively. The obtained value of mean sorption energy (EDR = 13.32 kJ/mol) suggested the chemisorption mechanism of As(V) adsorption on TM. The removal of As(V) was significantly decreased in the presence of phosphate ions. The As(V) loaded adsorbent was successfully regenerated using NaOH solution with insignificant loss of metals. Therefore, the results of the study demonstrated that TM could be considered as a promising adsorbent for the treatment of As(V) in drinking water. Copyright © 2013 Elsevier Ltd. All rights reserved.

Sonar atlas of caverns comprising the U.S. Strategic Petroleum Reserve. Volume 3, Bryan Mound Site, Texas.

Energy Technology Data Exchange (ETDEWEB)

Rautman, Christopher Arthur; Lord, Anna Snider

2007-09-01

Downhole sonar surveys from the four active U.S. Strategic Petroleum Reserve sites have been modeled and used to generate a four-volume sonar atlas, showing the three-dimensional geometry of each cavern. This volume 3 focuses on the Bryan Mound SPR site, located in southeastern Texas. Volumes 1, 2, and 4, respectively, present images for the Bayou Choctaw SPR site, Louisiana, the Big Hill SPR site, Texas, and the West Hackberry SPR site, Louisiana. The atlas uses a consistent presentation format throughout. The basic geometric measurements provided by the down-cavern surveys have also been used to generate a number of geometric attributes, the values of which have been mapped onto the geometric form of each cavern using a color-shading scheme. The intent of the various geometrical attributes is to highlight deviations of the cavern shape from the idealized cylindrical form of a carefully leached underground storage cavern in salt. The atlas format does not allow interpretation of such geometric deviations and anomalies. However, significant geometric anomalies, not directly related to the leaching history of the cavern, may provide insight into the internal structure of the relevant salt dome.

Utilization and facility of neutron activation analysis in HANARO research reactor

Energy Technology Data Exchange (ETDEWEB)

Chung, Y S; Chung, Y J; Moon, J H [Korea Atomic Energy Research Institute, P.O.Box 105 Yusong, 305-600, Taejon (Korea, Republic of)

1998-07-01

The facilities of neutron activation analysis within a multi-purpose research reactor (HANARO) are described and the main applications of Neutron activation analysis (NAA) in Korea are reviewed. The sample irradiation tube, automatic and manual pneumatic transfer system, are installed at three irradiation holes. One irradiation hole is lined with a cadmium tube for epithermal-nal NAA. The performance of the NAA facility was examined to identify the characteristics of tube transfer system, irradiation sites and polyethylene irradiation capsule. The available thermal neutron flux with each irradiation site are in the range of 3.9x10{sup 13}-1.6x10{sup 14} n/cm{sup 2}{center_dot}s and cadmium ratios are 15-250. Neutron activation analysis has been applied in the trace component analysis of nuclear, geological, biological, environmental and high purity materials and various polymers for research and development. Analytical services and the latest analytical results are summarized. (author)

On the anomalous concentrations of uranium in sediments from hydrothermal mounds. A geochemical roll-type mechanism

International Nuclear Information System (INIS)

Bernat, M.; Benhassaine, A.

1987-01-01

Sediments close to the nontronite formations of hydrothermal mounds often show anomalously high concentrations of uranium. This is frequently interpreted as being due to seeping of low temperature U bearing hydrothermal water through the basal basalt and into the overlying sediments. But we think that this phenomenon is the consequence of leaching of the sediment by hydrothermal water initially depleted in uranium. The migration of U is favoured by the pH of these water which dissolve the iron oxides and hydroxides giving Fe +++ ions in solution. The location and strength of the formed U anomalies are controlled by geochemical and hydrodynamicals factors. 22 refs [fr

Streamlined Approach for Environmental Restoration Plan for Corrective Action Unit 116: Area 25 Test Cell C Facility, Nevada Test Site, Nevada, Revision 1

International Nuclear Information System (INIS)

2008-01-01

This Streamlined Approach for Environmental Restoration (SAFER) Plan identifies the activities required for the closure of Corrective Action Unit (CAU) 116, Area 25 Test Cell C Facility. The Test Cell C (TCC) Facility is located in Area 25 of the Nevada Test Site (NTS) approximately 25 miles northwest of Mercury, Nevada (Figure 1). CAU 116 is currently listed in Appendix III of the Federal Facility Agreement and Consent Order (FFACO) of 1996 (as amended February 2008) and consists of two Corrective Action Sites (CASs): (1) CAS 25-23-20, Nuclear Furnace Piping; and (2) CAS 25-41-05, Test Cell C Facility. CAS 25-41-05 is described in the FFACO as the TCC Facility but actually includes Building 3210 and attached concrete shield wall only. CAU 116 will be closed by demolishing Building 3210, the attached concrete shield wall, and the nuclear furnace piping. In addition, as a best management practice (BMP), Building 3211 (moveable shed) will be demolished due to its close proximity to Building 3210. This will aid in demolition and disposal operations. Radiological surveys will be performed on the demolition debris to determine the proper disposal pathway. As much of the demolition debris as space allows will be placed into the Building 3210 basement structure. After filling to capacity with demolition debris, the basement structure will be mounded or capped and closed with administrative controls. Prior to beginning demolition activities and according to an approved Sampling and Analysis Plan (SAP), representative sampling of surface areas that are known, suspected, or have the potential to contain hazardous constituents such as lead or polychlorinated biphenyls (PCBs) will be performed throughout all buildings and structures. Sections 2.3.2, 4.2.2.2, 4.2.2.3, 4.3, and 6.2.6.1 address the methodologies employed that assure the solid debris placed in the basement structure will not contain contaminants of concern (COCs) above hazardous waste levels. The anticipated post

Linde FUSRAP Site Remediation: Engineering Challenges and Solutions of Remedial Activities on an Active Industrial Facility - 13506

International Nuclear Information System (INIS)

Beres, Christopher M.; Fort, E. Joseph; Boyle, James D.

2013-01-01

The Linde FUSRAP Site (Linde) is located in Tonawanda, New York at a major research and development facility for Praxair, Inc. (Praxair). Successful remediation activities at Linde combines meeting cleanup objectives of radiological contamination while minimizing impacts to Praxair business operations. The unique use of Praxair's property coupled with an array of active and abandoned utilities poses many engineering and operational challenges; each of which has been overcome during the remedial action at Linde. The U.S. Army Corps of Engineers - Buffalo District (USACE) and CABRERA SERVICES, INC. (CABRERA) have successfully faced engineering challenges such as relocation of an aboveground structure, structural protection of an active water line, and installation of active mechanical, electrical, and communication utilities to perform remediation. As remediation nears completion, continued success of engineering challenges is critical as remaining activities exist in the vicinity of infrastructure essential to business operations; an electrical substation and duct bank providing power throughout the Praxair facility. Emphasis on engineering and operations through final remediation and into site restoration will allow for the safe and successful completion of the project. (authors)

Linde FUSRAP Site Remediation: Engineering Challenges and Solutions of Remedial Activities on an Active Industrial Facility - 13506

Energy Technology Data Exchange (ETDEWEB)

Beres, Christopher M.; Fort, E. Joseph [Cabrera Services, Inc., 473 Silver Lane, East Hartford, CT 06118 (United States); Boyle, James D. [United States Army Corps of Engineers - Buffalo, 1776 Niagara Street, Buffalo, NY 14207 (United States)

2013-07-01

The Linde FUSRAP Site (Linde) is located in Tonawanda, New York at a major research and development facility for Praxair, Inc. (Praxair). Successful remediation activities at Linde combines meeting cleanup objectives of radiological contamination while minimizing impacts to Praxair business operations. The unique use of Praxair's property coupled with an array of active and abandoned utilities poses many engineering and operational challenges; each of which has been overcome during the remedial action at Linde. The U.S. Army Corps of Engineers - Buffalo District (USACE) and CABRERA SERVICES, INC. (CABRERA) have successfully faced engineering challenges such as relocation of an aboveground structure, structural protection of an active water line, and installation of active mechanical, electrical, and communication utilities to perform remediation. As remediation nears completion, continued success of engineering challenges is critical as remaining activities exist in the vicinity of infrastructure essential to business operations; an electrical substation and duct bank providing power throughout the Praxair facility. Emphasis on engineering and operations through final remediation and into site restoration will allow for the safe and successful completion of the project. (authors)

Strategic petroleum reserve, Byran Mound Salt Dome, Brazoria County, Texas. Final environmental impact statement (final supplement to FEA FES 76/77-6)

Energy Technology Data Exchange (ETDEWEB)

1977-12-01

On January 7, 1977, the Federal Energy Administration issued a Final Environmental Impact Statement (EIS) for the development of the Bryan Mound salt dome as a storage site for the Strategic Petroleum Reserve (FES 76/77-6). On October 1, 1977, the U.S. Department of Energy was created and the programs of the Federal Energy Administration were transferred to the new Department. As such, this final supplement is being issued by the Department of Energy. The salt dome is located in Brazoria County, Texas. Since the EIS was published, it has been determined that this arrangement would be inadequate to meet the long term requirements for filling and withdrawing oil at the site, although the disposal of brine to Dow Chemical would be utilized to the maximum extent possible. Therefore, on July 15, 1977, a Draft Supplement to FES 76/77-6 was issued addressing the environmental impacts of construction and operation of two types of brine disposal systems and a new water supply system. This final supplement addresses a brine injection well system and a water intake system. Construction of this new system component would cause temporary disruption to land use, water quality, air quality, and terrestrial and aquatic ecology. The new facilities would permanently change 17 acres of land from its present use. Operation of the systems would have relatively small, short-term impacts. Use of the brine surge pit could adversely affect air quality by emitting hydrocarbon vapors (maximum rate of 51.4 tons per year). Operation of the disposal wells would increase the salinity of an already saline aquifer. All operational impacts would be relatively minor and short-term, occurring only during periods of fill or withdrawal of the storage facility.

Strategic Petroleum Reserve (SPR) additional geologic site characterization studies, Bryan Mound Salt Dome, Texas

Energy Technology Data Exchange (ETDEWEB)

Neal, J.T. [Sandia National Labs., Albuquerque, NM (United States); Magorian, T.R.; Ahmad, S. [Acres International Corp., Amherst, NY (United States)

1994-11-01

This report revises the original report that was published in 1980. Some of the topics covered in the earlier report were provisional and it is now practicable to reexamine them using new or revised geotechnical data and that obtained from SPR cavern operations, which involves 16 new caverns. Revised structure maps and sections show interpretative differences as compared with the 1980 report and more definition in the dome shape and caprock structural contours, especially a major southeast-northwest trending anomalous zone. The original interpretation was of westward tilt of the dome, this revision shows a tilt to the southeast, consistent with other gravity and seismic data. This interpretation refines the evaluation of additional cavern space, by adding more salt buffer and allowing several more caverns. Additional storage space is constrained on this nearly full dome because of low-lying peripheral wetlands, but 60 MMBBL or more of additional volume could be gained in six or more new caverns. Subsidence values at Bryan Mound are among the lowest in the SPR system, averaging about 11 mm/yr (0.4 in/yr), but measurement and interpretation issues persist, as observed values are about the same as survey measurement accuracy. Periodic flooding is a continuing threat because of the coastal proximity and because peripheral portions of the site are at elevations less than 15 ft. This threat may increase slightly as future subsidence lowers the surface, but the amount is apt to be small. Caprock integrity may be affected by structural features, especially the faulting associated with anomalous zones. Injection wells have not been used extensively at Bryan Mound, but could be a practicable solution to future brine disposal needs. Environmental issues center on the areas of low elevation that are below 15 feet above mean sea level: the coastal proximity and lowland environment combined with the potential for flooding create conditions that require continuing surveillance.

Effect of climate changes in the holocene on the distribution of humic substances in the profile of forest-tundra peat mounds

Science.gov (United States)

Vasilevich, R. S.; Beznosikov, V. A.

2017-11-01

The molecular composition of humic substances in permafrost peatlands of the forest-tundra zone in northeastern European Russia has been characterized for the first time on the basis of systematic studies. Changes in the molar x(H): x(C) ratio along the peat profiles have been revealed, which is due to the activation of cryogenic processes in the upper part of the seasonally thawing layer, the natural selection of condensed humic molecules, and the botanical composition and degree of degradation of peat, which reflect the climatic features of the area in the Holocene. Dry-peat soils of mounds are worse heated during the summer period because of the buffering effect of moss litter, which results in a lower degree of condensation of humic and fulvic acid molecules in the peat horizons down to the permafrost table. Transformation of quantitative and qualitative parameters of specific organic compounds occurs at the permafrost boundary of peatlands, which can serve as an indicator of recent climate changes in high latitudes.

Impacts from Partial Removal of Decommissioned Oil and Gas Platforms on Fish Biomass and Production on the Remaining Platform Structure and Surrounding Shell Mounds.

Science.gov (United States)

Claisse, Jeremy T; Pondella, Daniel J; Love, Milton; Zahn, Laurel A; Williams, Chelsea M; Bull, Ann S

2015-01-01

When oil and gas platforms become obsolete they go through a decommissioning process. This may include partial removal (from the surface to 26 m depth) or complete removal of the platform structure. While complete removal would likely eliminate most of the existing fish biomass and associated secondary production, we find that the potential impacts of partial removal would likely be limited on all but one platform off the coast of California. On average 80% of fish biomass and 86% of secondary fish production would be retained after partial removal, with above 90% retention expected for both metrics on many platforms. Partial removal would likely result in the loss of fish biomass and production for species typically found residing in the shallow portions of the platform structure. However, these fishes generally represent a small proportion of the fishes associated with these platforms. More characteristic of platform fauna are the primarily deeper-dwelling rockfishes (genus Sebastes). "Shell mounds" are biogenic reefs that surround some of these platforms resulting from an accumulation of mollusk shells that have fallen from the shallow areas of the platforms mostly above the depth of partial removal. We found that shell mounds are moderately productive fish habitats, similar to or greater than natural rocky reefs in the region at comparable depths. The complexity and areal extent of these biogenic habitats, and the associated fish biomass and production, will likely be reduced after either partial or complete platform removal. Habitat augmentation by placing the partially removed platform superstructure or some other additional habitat enrichment material (e.g., rock boulders) on the seafloor adjacent to the base of partially removed platforms provides additional options to enhance fish production, potentially mitigating reductions in shell mound habitat.

Impacts from Partial Removal of Decommissioned Oil and Gas Platforms on Fish Biomass and Production on the Remaining Platform Structure and Surrounding Shell Mounds.

Directory of Open Access Journals (Sweden)

Jeremy T Claisse

Full Text Available When oil and gas platforms become obsolete they go through a decommissioning process. This may include partial removal (from the surface to 26 m depth or complete removal of the platform structure. While complete removal would likely eliminate most of the existing fish biomass and associated secondary production, we find that the potential impacts of partial removal would likely be limited on all but one platform off the coast of California. On average 80% of fish biomass and 86% of secondary fish production would be retained after partial removal, with above 90% retention expected for both metrics on many platforms. Partial removal would likely result in the loss of fish biomass and production for species typically found residing in the shallow portions of the platform structure. However, these fishes generally represent a small proportion of the fishes associated with these platforms. More characteristic of platform fauna are the primarily deeper-dwelling rockfishes (genus Sebastes. "Shell mounds" are biogenic reefs that surround some of these platforms resulting from an accumulation of mollusk shells that have fallen from the shallow areas of the platforms mostly above the depth of partial removal. We found that shell mounds are moderately productive fish habitats, similar to or greater than natural rocky reefs in the region at comparable depths. The complexity and areal extent of these biogenic habitats, and the associated fish biomass and production, will likely be reduced after either partial or complete platform removal. Habitat augmentation by placing the partially removed platform superstructure or some other additional habitat enrichment material (e.g., rock boulders on the seafloor adjacent to the base of partially removed platforms provides additional options to enhance fish production, potentially mitigating reductions in shell mound habitat.

RCRA and CERCLA requirements affecting cleanup activities at a federal facility superfund site

International Nuclear Information System (INIS)

Walsh, T.J.

1994-01-01

The Fernald Environmental Management Project (FEMP) achieved success on an integrated groundwater monitoring program which addressed both RCRA and CERCLA requirements. The integrated plan resulted in a cost savings of approximately $2.6 million. At present, the FEMP is also working on an integrated closure process to address Hazardous Waste Management Units (HWMUs) at the site. To date, Ohio EPA seems willing to discuss an integrated program with some stipulations. If an integrated program is implemented, a cost savings of several million dollars will be realized since the CERCLA documents can be used in place of a RCRA closure plan. The success of an integrated program at the FEMP is impossible without the support of DOE and the regulators. Since DOE is an owner/operator of the facility and Ohio EPA regulates hazardous waste management activities at the FEMP, both parties must be satisfied with the proposed integration activities. Similarly, US EPA retains CERCLA authority over the site along with a signed consent agreement with DOE, which dictates the schedule of the CERCLA activities. Another federal facility used RCRA closure plans to satisfy CERCLA activities. This federal facility was in a different US EPA Region than the FEMP. While this approach was successful for this site, an integrated approach was required at the FEMP because of the signed Consent Agreement and Consent Decree. For federal facilities which have a large number of HWMUs along with OUs, an integrated approach may result in a timely and cost-effective cleanup

Discovery of Widespread Biogenic Methane Emissions and Authigenic Carbonate Mound-like Structures at the Aquitaine Shelf (Bay of Biscay)

Science.gov (United States)

Dupré, S.; Loubrieu, B.; Scalabrin, C.; Ehrhold, A.; Gautier, E.; Ruffine, L.; Pierre, C.; Battani, A.; Le Bouffant, N.; Berger, L.

2014-12-01

Fishery acoustic surveys conducted in the Bay of Biscay (1998-2012) and dedicated to monitoring and predicting pelagic ecosystem evolution reveal numerous active seeps on the Aquitaine Shelf, east of the shelf break (Dupré et al. 2014). Seafloor and water column acoustic investigation with the use of ship-borne multibeam echosounder in 2013 (Gazcogne1 marine expedition) confirmed the presence of numerous (> 3000) persistent and widespread gas emission sites at water depths ranging from ~140 to 180 m. These fluid emissions are associated at the seafloor with high backscatter subcircular small-scale mounds, on average less than 2 m high and a few meters in diameter. Near-bottom visual observations and samplings were conducted with the ROV (Remotely Operated Vehicle) Victor (Gazcogne2 expedition). The whole mounds cover an area of ~200 km2 of the seabed, and are by-products of gas seepage, i.e. methane-derived authigenic carbonates. The spatial distribution of the seeps and related structures, based on water column acoustic gas flares and high backscatter seabed patches, appears to be relatively broad, with a North-South extension of ~80 km across the Parentis Basin and the Landes High, and a West-East extension along a few kilometers wide on the shelf, up to 8 km. Gas bubbles sampled at in situ conditions are principally composed of biogenic methane, possibly originated from Late Pleistocene deposits. The volume of methane emitted into the water column is abundant i) with an average gas flux varying locally from 0.035 to 0.37 Ln/min and ii) with regard to the time needed for the precipitation of the authigenic carbonates identified both at the seabed and in the upper most sedimentary column. The GAZCOGNE study is co-funded by TOTAL and IFREMER as part of the PAMELA (Passive Margin Exploration Laboratories) scientific project. ReferenceDupré, S., Berger, L., Le Bouffant, N., Scalabrin, C., and Bourillet, J.-F., 2014. Fluid emissions at the Aquitaine Shelf (Bay of

Analysis of cavern stability at the Bryan Mound SPR site.

Energy Technology Data Exchange (ETDEWEB)

Ehgartner, Brian L.; Sobolik, Steven Ronald

2009-04-01

This report presents computational analyses that simulate the structural response of caverns at the Strategic Petroleum Reserve Bryan Mound site. The cavern field comprises 20 caverns. Five caverns (1, 2, 4, and 5; 3 was later plugged and abandoned) were acquired from industry and have unusual shapes and a history dating back to 1946. The other 16 caverns (101-116) were leached according to SPR standards in the mid-1980s and have tall cylindrical shapes. The history of the caverns and their shapes are simulated in a 3-D geomechanics model of the site that predicts deformations, strains, and stresses. Future leaching scenarios due to oil drawdowns using fresh water are also simulated by increasing the volume of the caverns. Cavern pressures are varied in the model to capture operational practices in the field. The results of the finite element model are interpreted to provide information on the current and future status of subsidence, well integrity, and cavern stability. The most significant result in this report is relevant to caverns 1, 2, and 5. The caverns have non-cylindrical shapes and have potential regions where the surrounding salt may be damaged during workover procedures. During a workover the normal cavern operating pressure is lowered to service a well. At this point the wellhead pressures are atmospheric. When the workover is complete, the cavern is repressurized. The resulting elastic stresses are sufficient to cause tension and large deviatoric stresses at several locations. With time, these stresses relax to a compressive state due to salt creep. However, the potential for salt damage and fracturing exists. The analyses predict tensile stresses at locations with sharp-edges in the wall geometry, or in the case of cavern 5, in the neck region between the upper and lower lobes of the cavern. The effects do not appear to be large-scale, however, so the only major impact is the potential for stress-induced salt falls in cavern 5, potentially leading to

Naturally occurring workplace facilities to increase the leisure time physical activity of workers: A propensity-score weighted population study.

Science.gov (United States)

Biswas, Aviroop; Smith, Peter M; Gignac, Monique A M

2018-06-01

The benefit of providing access to physical activity facilities at or near work to support the leisure time physical activity (LTPA) of workers is uncertain. We examined the association between access to physical activity facilities at or near work and the LTPA of workers after adjusting for a range of individual and occupational characteristics. Data was obtained from 60,650 respondents to the 2007-2008 Canadian Community Health Survey. Participants were employed adults ≥18 years of age who had no long-term health condition which reduced their participation in physical activity. Latent class analysis determined naturally occurring combinations of physical activity facilities at or near work. Each combination was balanced by 19 individual and occupational covariate characteristics using inverse probability of treatment weights derived from propensity scores. The association between combinations of physical activity facilities at or near work on LTPA level was estimated by multinomial logistic regression. Five different combinations of physical activity facilities were available to respondents at or near work. Data were analyzed in 2017. All possible physical facilities increased the likelihood for LTPA (OR, 2.08, 95% CI, 1.03-4.20) and other combinations were also positively associated. Respondents with no physical activity facilities were characterized as having a low education, low income, high physically demanding work, poor health and mental health, non-white racial background, and being an immigrant. Access to supportive workplace environments can help workers be physically active. Future research should assess a range of personal, social and environmental factors that may be driving this relationship.

Prompt gamma neutron activation analysis facility at the RA-6 research reactor

International Nuclear Information System (INIS)

Sanchez, F. A.; Calzetta, O

2004-01-01

A prompt gamma neutron activation activation analysis facility was developed at the 500 kw thermal power RA-6 research reactor of the Bariloche Atomic Center, Argentina.This facility consist of a radial beam port with external positioning of the sample.The gamma radiation is reduced by a bismuth filter placed inside the extraction tube and the beam diameter is limited by a set of two collimators up to 5 cm.The neutron flux at the sample position is 7 10 6 n/cm 2 s with a Cadmium ratio of 20/1.The gamma detector is a 50 % efficiency type p HPGe rounded by a NaI(Tl) for Compton suppressioning.The gamma spectra is measured through 0 to 8.5 MeV.The background have counting rate of 350 cps without sample. In this work is shown the efficiency curve, the calculed sensibilities and the lower detection limits for B, Cd, Sm, Gd, H, Cl, Hg, Eu, Ti, Ag, Au, Mo. The RA-6's PGNAA facility is fully working, although the analytic capacity is under improvement [es

Recent activities at the ORNL multicharged ion research facility (MIRF)

International Nuclear Information System (INIS)

Meyer, F.W.; Bannister, M.E.; Hale, J.W.; Havener, C.C.; Krause, H.F.; Vane, C.R.; Deng, S.; Draganic, I.N.; Harris, P.R.

2012-01-01

Recent activities at the ORNL Multicharged Ion Research Facility (MIRF) are summarized. A brief summary of the MIRF high voltage (HV) platform and floating beam line upgrade is provided. An expansion of our research program to the use of molecular ion beams in heavy-particle and electron collisions, as well as in ion surface interactions is described, and a brief description is provided of the most recently added Ion Cooling and Characterization End-station (ICCE) trap. With the expansion to include molecular ion beams, the acronym MIRF for the facility, however, remains unchanged: 'M' can now refer to either 'Multicharged' or 'Molecular'. The paper is followed by the slides of the presentation. (authors)

Naturally occurring workplace facilities to increase the leisure time physical activity of workers: A propensity-score weighted population study

Directory of Open Access Journals (Sweden)

Aviroop Biswas

2018-06-01

Full Text Available The benefit of providing access to physical activity facilities at or near work to support the leisure time physical activity (LTPA of workers is uncertain. We examined the association between access to physical activity facilities at or near work and the LTPA of workers after adjusting for a range of individual and occupational characteristics. Data was obtained from 60,650 respondents to the 2007–2008 Canadian Community Health Survey. Participants were employed adults ≥18 years of age who had no long-term health condition which reduced their participation in physical activity. Latent class analysis determined naturally occurring combinations of physical activity facilities at or near work. Each combination was balanced by 19 individual and occupational covariate characteristics using inverse probability of treatment weights derived from propensity scores. The association between combinations of physical activity facilities at or near work on LTPA level was estimated by multinomial logistic regression. Five different combinations of physical activity facilities were available to respondents at or near work. Data were analyzed in 2017. All possible physical facilities increased the likelihood for LTPA (OR, 2.08, 95% CI, 1.03–4.20 and other combinations were also positively associated. Respondents with no physical activity facilities were characterized as having a low education, low income, high physically demanding work, poor health and mental health, non-white racial background, and being an immigrant. Access to supportive workplace environments can help workers be physically active. Future research should assess a range of personal, social and environmental factors that may be driving this relationship. Keywords: Physical activity, Workplace, Built environment, Health promotion, Exercise

Conservation and restoration of archaeological textiles from the disturbed Altai burial mounds of the early Iron age

Directory of Open Access Journals (Sweden)

Altynbekova Dana Kyrymovna

2015-09-01

Full Text Available The article deals with the experience of scientific-restoration laboratory “Ostrov Krym” of the conservation and restoration of archaeological textiles from disturbed mounds of the IV–III centuries BC, located in the Kazakh Altai. The specialists of the laboratory participate in field works, carrying out the extraction of large blocks/monoliths with findings, using methods of forming blocks developed in practice. Two methods are considered aimed on conservation of textiles recovered from excavation blocks, depending on their content. The first method is a sequential splitting of the block into its components with random set of fragments of organic material. The process of stratification of the conglomerate as well as the stabilization of the separated fragments and their identification is described. During the reconstruction of the textiles the well-preserved analogs of synchronous Altai burial mounds located on the territory of Russia and Mongolia have been used. Examples of reconstruction the pieces of felt are represented. The second method consists in preservation of the blocks without dissection. It is applied in case of their content has been considered as specific independent complex. The process of conservation is shown by the case-study of the fifth set, extracted from the excavation with the remains of the horse in the wet state. Conservation of dissimilar materials (fabric, felt, vegetable stuffing pillows, a tree with the metallic remains in the form of conglomerate has been carried out similarly to the conservation of wet archaeological wood. The block stabilization has been made in the wet state with a gradual replacement of the soil solution by consolidator.

Nuclear Rocket Facility Decommissioning Project: Controlled Explosive Demolition of Neutron-Activated Shield Wall

International Nuclear Information System (INIS)

Michael R, Kruzic

2008-01-01

Located in Area 25 of the Nevada Test Site (NTS), the Test Cell A (TCA) Facility (Figure 1) was used in the early to mid-1960s for testing of nuclear rocket engines, as part of the Nuclear Rocket Development Program, to further space travel. Nuclear rocket testing resulted in the activation of materials around the reactors and the release of fission products and fuel particles. The TCA facility, known as Corrective Action Unit 115, was decontaminated and decommissioned (D and D) from December 2004 to July 2005 using the Streamlined Approach for Environmental Restoration (SAFER) process, under the Federal Facility Agreement and Consent Order. The SAFER process allows environmental remediation and facility closure activities (i.e., decommissioning) to occur simultaneously, provided technical decisions are made by an experienced decision maker within the site conceptual site model. Facility closure involved a seven-step decommissioning strategy. First, preliminary investigation activities were performed, including review of process knowledge documentation, targeted facility radiological and hazardous material surveys, concrete core drilling and analysis, shield wall radiological characterization, and discrete sampling, which proved to be very useful and cost-effective in subsequent decommissioning planning and execution and worker safety. Second, site setup and mobilization of equipment and personnel were completed. Third, early removal of hazardous materials, including asbestos, lead, cadmium, and oil, was performed ensuring worker safety during more invasive demolition activities. Process piping was to be verified void of contents. Electrical systems were de-energized and other systems were rendered free of residual energy. Fourth, areas of high radiological contamination were decontaminated using multiple methods. Contamination levels varied across the facility. Fixed beta/gamma contamination levels ranged up to 2 million disintegrations per minute (dpm)/100

Nuclear Rocket Facility Decommissioning Project: Controlled Explosive Demolition of Neutron-Activated Shield Wall

Energy Technology Data Exchange (ETDEWEB)

Michael R. Kruzic

2008-06-01

Located in Area 25 of the Nevada Test Site (NTS), the Test Cell A (TCA) Facility (Figure 1) was used in the early to mid-1960s for testing of nuclear rocket engines, as part of the Nuclear Rocket Development Program, to further space travel. Nuclear rocket testing resulted in the activation of materials around the reactors and the release of fission products and fuel particles. The TCA facility, known as Corrective Action Unit 115, was decontaminated and decommissioned (D&D) from December 2004 to July 2005 using the Streamlined Approach for Environmental Restoration (SAFER) process, under the Federal Facility Agreement and Consent Order. The SAFER process allows environmental remediation and facility closure activities (i.e., decommissioning) to occur simultaneously, provided technical decisions are made by an experienced decision maker within the site conceptual site model. Facility closure involved a seven-step decommissioning strategy. First, preliminary investigation activities were performed, including review of process knowledge documentation, targeted facility radiological and hazardous material surveys, concrete core drilling and analysis, shield wall radiological characterization, and discrete sampling, which proved to be very useful and cost-effective in subsequent decommissioning planning and execution and worker safety. Second, site setup and mobilization of equipment and personnel were completed. Third, early removal of hazardous materials, including asbestos, lead, cadmium, and oil, was performed ensuring worker safety during more invasive demolition activities. Process piping was to be verified void of contents. Electrical systems were de-energized and other systems were rendered free of residual energy. Fourth, areas of high radiological contamination were decontaminated using multiple methods. Contamination levels varied across the facility. Fixed beta/gamma contamination levels ranged up to 2 million disintegrations per minute (dpm)/100

An aerial radiological survey of the EG ampersand G Mound Applied Technologies and surrounding area, Miamisburg, Ohio

International Nuclear Information System (INIS)

1992-11-01

An aerial radiological survey was conducted over EG ampersand G Mound Applied Technologies, Miamisburg, Ohio, during the period of June 9--24, 1989. The purpose of the 41-square-kilometer (16-square-mile) survey was to document the terrestrial gamma environment of the plant and surrounding area. In addition, ground-based exposure rate measurements and soil samples were obtained to support the aerial data. An exposure rate contour map at 1 meter above ground level was.constructed from the gamma data and overlaid on an aerial photograph and map of the area. Exposure rates measured in the area typically ranged from 9 to 11 microroentgens per hour (μR/h)

Offshore oceanographic and environmental monitoring services for the Strategic Petroleum Reserve. Volume I. Appendices. Annual report for the Bryan Mound Site, September 1982-August 1983

Energy Technology Data Exchange (ETDEWEB)

None

1984-03-01

The Department of Energy's Strategic Petroleum Reserve Program began leaching the Bryan Mound salt dome and discharging brine into the coastal waters offshore of Freeport, Texas on March 10, 1980. This report describes the findings of a team of Texas A and M University scientists and engineers who have conducted a study to evaluate the effects of the Bryan Mound brine discharge on the marine environment. The study addresses the areas of physical oceanography, analysis of the discharge plume, water and sediment quality, nekton, benthos and data management. It focuses on the period from September 1982 through August 1983. The ambient physical environment and its temporal and spatial variability were studied by means of continuously recording in situ current/conductivitiy/temperature meters and twelve, one-day synoptic hydrographic cruises. The quarterly water and sediment quality data show a small increase in salinity, sodium and chloride ions occurs in the bottom waters and sediment pore waters near the diffuser relative to those values measured at stations farther away. Data from the brine plume study for this reporting study show the largest areal extent within the +1 o/oo above ambient salinity contour was 40.0 km/sup 2/ which occurred on August 11, 1983. It appears that brine disposal at Bryan Mound has had neglible if any influence on the nekton community surrounding the diffuser. The benthic quarterly data from 26 stations, including 7 collections made after the diffuser outflow rate was increased to 1,000,000 barrels/day, show the total numbers of species at the diffuser station were higher than most other nearfield stations as well as many farfield stations in both the pre- and post-1,000,000 barrels/day brine flow periods. 138 references, 175 figures, 53 tables.

Facility effluent monitoring plan for the 325 Facility

International Nuclear Information System (INIS)

1998-01-01

The Applied Chemistry Laboratory (325 Facility) houses radiochemistry research, radioanalytical service, radiochemical process development, and hazardous and mixed hazardous waste treatment activities. The laboratories and specialized facilities enable work ranging from that with nonradioactive materials to work with picogram to kilogram quantities of fissionable materials and up to megacurie quantities of other radionuclides. The special facilities include two shielded hot-cell areas that provide for process development or analytical chemistry work with highly radioactive materials, and a waste treatment facility for processing hazardous, mixed, low-level, and transuranic wastes generated by Pacific Northwest Laboratory. Radioactive material storage and usage occur throughout the facility and include a large number of isotopes. This material is in several forms, including solid, liquid, particulate, and gas. Some of these materials are also heated during testing which can produce vapors. The research activities have been assigned to the following activity designations: High-Level Hot Cell, Hazardous Waste Treatment Unit, Waste Form Development, Special Testing Projects, Chemical Process Development, Analytical Hot Cell, and Analytical Chemistry. The following summarizes the airborne and liquid effluents and the results of the Facility Effluent Monitoring Plan (FEMP) determination for the facility. The complete monitoring plan includes characterization of effluent streams, monitoring/sampling design criteria, a description of the monitoring systems and sample analysis, and quality assurance requirements

School Playground Facilities as a Determinant of Children's Daily Activity: A Cross-Sectional Study of Danish Primary School Children

DEFF Research Database (Denmark)

Nielsen, Glen; Bugge, Anna; El-Naaman, Bianca

2012-01-01

This study investigates the influence of school playground facilities on children's daily physical activity.......This study investigates the influence of school playground facilities on children's daily physical activity....

Self-sustainability of a research reactor facility with neutron activation analysis

International Nuclear Information System (INIS)

Chilian, C.; Kennedy, G.

2010-01-01

Long-term self-sustainability of a small reactor facility is possible because there is a large demand for non-destructive chemical analysis of bulk materials that can only be achieved with neutron activation analysis (NAA). The Ecole Polytechnique Montreal SLOWPOKE Reactor Facility has achieved self-sustainability for over twenty years, benefiting from the extreme reliability, ease of use and stable neutron flux of the SLOWPOKE reactor. The industrial clientele developed slowly over the years, mainly because of research users of the facility. A reliable NAA service with flexibility, high accuracy and fast turn-around time was achieved by developing an efficient NAA system, using a combination of the relative and k0 standardisation methods. The techniques were optimized to meet the specific needs of the client, such as low detection limit or high accuracy at high concentration. New marketing strategies are presented, which aim at a more rapid expansion. (author)

The design status of the liquid lithium target facility of IFMIF at the end of the engineering design activities

Energy Technology Data Exchange (ETDEWEB)

Nitti, F.S., E-mail: francesco.nitti@enea.it [IFMIF/EVEDA Project Team, Rokkasho Japan (Japan); Ibarra, A. [CIEMAT, Madrid (Spain); Ida, M. [IHI Corporation, Tokyo (Japan); Favuzza, P. [ENEA Research Center Firenze (Italy); Furukawa, T. [JAEA Research Center, Tokai-mura, Ibaraki (Japan); Groeschel, F. [KIT Research Center, Karlsruhe (Germany); Heidinger, R. [F4E Research Center, Garching (Germany); Kanemura, T. [JAEA Research Center, Tokai-mura, Ibaraki (Japan); Knaster, J. [IFMIF/EVEDA Project Team, Rokkasho Japan (Japan); Kondo, H. [JAEA Research Center, Tokai-mura, Ibaraki (Japan); Micchiche, G. [ENEA Research Center, Brasimone (Italy); Sugimoto, M. [JAEA Research Center, Rokkasho Japan (Japan); Wakai, E. [JAEA Research Center, Tokai-mura, Ibaraki (Japan)

2015-11-15

Highlights: • Results of validation and design activity for the Li loop facility of IFMIF. • Demonstration of Li target stability, with surface disturbance <1 mm. • Demonstration of start-up and shut down procedures of Li loop. • Complete design of the heat removal system and C and O purification system. • Conceptual design of N and H isotopes purification systems. - Abstract: The International Fusion Material Irradiation Facility (IFMIF) is an experimental facility conceived for qualifying and characterizing structural materials for nuclear fusion applications. The Engineering Validation and Engineering Design Activity (EVEDA) is a fundamental step towards the final design. It presented two mandates: the Engineering Validation Activities (EVA), still on-going, and the Engineering Design Activities (EDA) accomplished on schedule in June 2013. Five main facilities are identified in IFMIF, among which the Lithium Target Facility constituted a technological challenge overcome thanks to the success of the main validation challenges impacting the design. The design of the liquid Lithium Target Facility at the end of the EDA phase is here detailed.

The design status of the liquid lithium target facility of IFMIF at the end of the engineering design activities

International Nuclear Information System (INIS)

Nitti, F.S.; Ibarra, A.; Ida, M.; Favuzza, P.; Furukawa, T.; Groeschel, F.; Heidinger, R.; Kanemura, T.; Knaster, J.; Kondo, H.; Micchiche, G.; Sugimoto, M.; Wakai, E.

2015-01-01

Highlights: • Results of validation and design activity for the Li loop facility of IFMIF. • Demonstration of Li target stability, with surface disturbance <1 mm. • Demonstration of start-up and shut down procedures of Li loop. • Complete design of the heat removal system and C and O purification system. • Conceptual design of N and H isotopes purification systems. - Abstract: The International Fusion Material Irradiation Facility (IFMIF) is an experimental facility conceived for qualifying and characterizing structural materials for nuclear fusion applications. The Engineering Validation and Engineering Design Activity (EVEDA) is a fundamental step towards the final design. It presented two mandates: the Engineering Validation Activities (EVA), still on-going, and the Engineering Design Activities (EDA) accomplished on schedule in June 2013. Five main facilities are identified in IFMIF, among which the Lithium Target Facility constituted a technological challenge overcome thanks to the success of the main validation challenges impacting the design. The design of the liquid Lithium Target Facility at the end of the EDA phase is here detailed.

Derivation of activity limits for the disposal of radioactive waste in near surface disposal facilities

International Nuclear Information System (INIS)

2003-12-01

criteria for disposal of radioactive wastes to near surface facilities. These criteria are qualitative in nature and, for example, they do not address limitations on radionuclide content of waste, waste packages or the facility as a whole. This publication is to present an approach for establishing radiological waste acceptance criteria using a safety assessment methodology and to illustrate its application in establishing limits on the total activity and the activity concentrations of radioactive waste to be disposed in near surface disposal facilities. The approach makes use of accepted methods and computational schemes currently used in assessing the safety of near surface disposal facilities both during the operational and post-closure periods. The scope of this publication covers the use of safety assessment methodology to calculate total and specific activities limits for radioactive waste in near surface disposal facilities. It is used to evaluate the potential operational and post-closure radiological impact of solid and solidified radioactive waste in near surface facilities. The radioactive waste types used to illustrate the approach range from waste containing radionuclides used for medical, industrial and research purposes to waste arising from nuclear fuel cycle activities. They also include waste arising from the decommissioning of nuclear facilities. The focus of the publication is on using of safety assessment methodology in derivation of quantitative radioactivity limits. This report deals with the role of activity limits in disposal system safety (Section 2), the relevant radiation protection criteria (Section 3), the approach to derive activity limits (Section 4), illustrations of the application of this approach (Section 5), and guidance on the use of the approach (Section 6)

Physical activity opportunities in Canadian childcare facilities: a provincial/territorial review of legislation.

Science.gov (United States)

Vanderloo, Leigh M; Tucker, Patricia; Ismail, Ali; van Zandvroort, Melissa M

2012-05-01

Preschoolers spend a substantial portion of their day in childcare; therefore, these centers are an ideal venue to encourage healthy active behaviors. It is important that provinces'/territories' childcare legislation encourage physical activity (PA) opportunities. The purpose of this study was to review Canadian provincial/territorial childcare legislation regarding PA participation. Specifically, this review sought to 1) appraise each provincial/territorial childcare regulation for PA requirements, 2) compare such regulations with the NASPE PA guidelines, and 3) appraise these regulations regarding PA infrastructure. A review of all provincial/territorial childcare legislation was performed. Each document was reviewed separately by 2 researchers, and the PA regulations were coded and summarized. The specific provincial/territorial PA requirements (eg, type/frequency of activity) were compared with the NASPE guidelines. PA legislation for Canadian childcare facilities varies greatly. Eight of the thirteen provinces/territories provide PA recommendations; however, none provided specific time requirements for daily PA. All provinces/territories did require access to an outdoor play space. All Canadian provinces/territories lack specific PA guidelines for childcare facilities. The development, implementation, and enforcement of national PA legislation for childcare facilities may aid in tackling the childhood obesity epidemic and assist childcare staff in supporting and encouraging PA participation.

The Prompt Gamma Neutron Activation Analysis Facility at ICN-Pitesti

International Nuclear Information System (INIS)

Barbos, D.; Paunoiu, C.; Mladin, M.; Cosma, C.

2008-01-01

PGNAA is a very widely applicable technique for determining the presence and amount of many elements simultaneously in samples ranging in size from micrograms to many grams. PGNAA is characterized by its capability for nondestructive multi-elemental analysis and its ability to analyse elements that cannot be determined by INAA. By means of this PGNAA method we are able to increase the performance of INAA method. A facility has been developed at Institute for Nuclear Research-Pitesti so that the unique features of prompt gamma-ray neutron activation analysis can be used to measure trace and major elements in samples. The facility is linked at the radial neutron beam tube at ACPR-TRIGA reactor. During the PGNAA-facility is in use the ACPR reactor will be operated in steady-state mode at 250 KW maximum power. The facility consists of a radial beam-port, external sample position with shielding, and induced prompt gamma-ray counting system.Thermal neutron flux with energy lower than cadmium cut-off at the sample position was measured using thin gold foil is: φ scd = 1.10 6 n/cm 2 /s with a cadmium ratio of:80.The gamma-ray detection system consist of an HpGe detector of 16% efficiency (detector model GC1518) with 1.85 keV resolution capability. The HpGe is mounted with its axis at 90 deg. with respect to the incident neutron beam at distance about 200mm from the sample position. To establish the performance capabilities of the facility, irradiation of pure element or sample compound standards were performed to identify the gama-ray energies from each element and their count rates

Ecological feedbacks. Termite mounds can increase the robustness of dryland ecosystems to climatic change.

Science.gov (United States)

Bonachela, Juan A; Pringle, Robert M; Sheffer, Efrat; Coverdale, Tyler C; Guyton, Jennifer A; Caylor, Kelly K; Levin, Simon A; Tarnita, Corina E

2015-02-06

Self-organized spatial vegetation patterning is widespread and has been described using models of scale-dependent feedback between plants and water on homogeneous substrates. As rainfall decreases, these models yield a characteristic sequence of patterns with increasingly sparse vegetation, followed by sudden collapse to desert. Thus, the final, spot-like pattern may provide early warning for such catastrophic shifts. In many arid ecosystems, however, termite nests impart substrate heterogeneity by altering soil properties, thereby enhancing plant growth. We show that termite-induced heterogeneity interacts with scale-dependent feedbacks to produce vegetation patterns at different spatial grains. Although the coarse-grained patterning resembles that created by scale-dependent feedback alone, it does not indicate imminent desertification. Rather, mound-field landscapes are more robust to aridity, suggesting that termites may help stabilize ecosystems under global change. Copyright © 2015, American Association for the Advancement of Science.

Characterization of magnetic material in the mound-building termite Macrotermes gilvus in Southeast Asia

Energy Technology Data Exchange (ETDEWEB)

Esa, Mohammad Faris Mohammad; Hassan, Ibrahim Haji [School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, Bangi, Selangor (Malaysia); Rahim, Faszly; Hanifah, Sharina Abu [School of Environmental Scieces and Natural Resources Faculty of Science and Technology, Universiti Kebangsaan Malaysia, Bangi, Selangor (Malaysia)

2015-09-25

Magnetic material such as magnetite are known as particles that respond to external magnetic field with their ferromagnetic properties as they are believed contribute to in responding to the geomagnetic field. These particles are used by terrestrial animals such as termites for navigation and orientation. Since our earth react as giant magnetic bar, the magnitude of this magnetic field present by intensity and direction (inclination and direction). The magnetic properties and presence of magnetite in termites Macrotermes gilvus, common mound-building termite were tested. M. gilvus termites was tested with a Vibrating Sample Magnetometer VSM to determine the magnetic properties of specimen. The crushed body sample was characterized with X-Ray Diffraction XRD to show the existent of magnetic material (magnetite) in the specimens. Results from VSM indicate that M. gilvus has diamagnetism properties. The characterization by XRD shows the existent of magnetic material in our specimen in low concentration.

Characterization of magnetic material in the mound-building termite Macrotermes gilvus in Southeast Asia

International Nuclear Information System (INIS)

Esa, Mohammad Faris Mohammad; Hassan, Ibrahim Haji; Rahim, Faszly; Hanifah, Sharina Abu

2015-01-01

Magnetic material such as magnetite are known as particles that respond to external magnetic field with their ferromagnetic properties as they are believed contribute to in responding to the geomagnetic field. These particles are used by terrestrial animals such as termites for navigation and orientation. Since our earth react as giant magnetic bar, the magnitude of this magnetic field present by intensity and direction (inclination and direction). The magnetic properties and presence of magnetite in termites Macrotermes gilvus, common mound-building termite were tested. M. gilvus termites was tested with a Vibrating Sample Magnetometer VSM to determine the magnetic properties of specimen. The crushed body sample was characterized with X-Ray Diffraction XRD to show the existent of magnetic material (magnetite) in the specimens. Results from VSM indicate that M. gilvus has diamagnetism properties. The characterization by XRD shows the existent of magnetic material in our specimen in low concentration

Characterization of magnetic material in the mound-building termite Macrotermes gilvus in Southeast Asia

Science.gov (United States)

Esa, Mohammad Faris Mohammad; Rahim, Faszly; Hassan, Ibrahim Haji; Hanifah, Sharina Abu

2015-09-01

Magnetic material such as magnetite are known as particles that respond to external magnetic field with their ferromagnetic properties as they are believed contribute to in responding to the geomagnetic field. These particles are used by terrestrial animals such as termites for navigation and orientation. Since our earth react as giant magnetic bar, the magnitude of this magnetic field present by intensity and direction (inclination and direction). The magnetic properties and presence of magnetite in termites Macrotermes gilvus, common mound-building termite were tested. M. gilvus termites was tested with a Vibrating Sample Magnetometer VSM to determine the magnetic properties of specimen. The crushed body sample was characterized with X-Ray Diffraction XRD to show the existent of magnetic material (magnetite) in the specimens. Results from VSM indicate that M. gilvus has diamagnetism properties. The characterization by XRD shows the existent of magnetic material in our specimen in low concentration.

Active seismic response control systems for nuclear power plant equipment facilities

International Nuclear Information System (INIS)

Kobori, Takuji; Kanayama, Hiroo; Kamagata, Shuichi

1989-01-01

To sustain severe earthquake ground motion, a new type of anti-seismic structure is proposed, called a Dynamic Intelligent Building (DIB) system, which is positioned as an active seismic response controlled the structure. The structural concept starts from a new recognition of earthquake ground motion, and the structural natural frequency is actively adjusted to avoid resonant vibration, and similarly the external counter-force cancels the resonant force which comes from the dynamic structural motion energy. These concepts are verified using an analytical simulator program. The advanced application of the DIB system, is the Active Supporting system and the Active Stabilizer system for nuclear power plant equipment facilities. (orig.)

Shared use of school facilities with community organizations and afterschool physical activity program participation: a cost-benefit assessment.

Science.gov (United States)

Kanters, Michael A; Bocarro, Jason N; Filardo, Mary; Edwards, Michael B; McKenzie, Thomas L; Floyd, Myron F

2014-05-01

Partnerships between school districts and community-based organizations to share school facilities during afterschool hours can be an effective strategy for increasing physical activity. However, the perceived cost of shared use has been noted as an important reason for restricting community access to schools. This study examined shared use of middle school facilities, the amount and type of afterschool physical activity programs provided at middle schools together with the costs of operating the facilities. Afterschool programs were assessed for frequency, duration, and type of structured physical activity programs provided and the number of boys and girls in each program. School operating costs were used to calculate a cost per student and cost per building square foot measure. Data were collected at all 30 middle schools in a large school district over 12 months in 2010-2011. Policies that permitted more use of school facilities for community-sponsored programs increased participation in afterschool programs without a significant increase in operating expenses. These results suggest partnerships between schools and other community agencies to share facilities and create new opportunities for afterschool physical activity programs are a promising health promotion strategy. © 2014, American School Health Association.

Quality control activities in support of the plutonium workers study. Assessment of coding consistency for data collected at Rocky Flats

International Nuclear Information System (INIS)

Reyes, M.; Wilkinson, G.S.; Acquavella, J.F.

1984-03-01

The Plutonium Workers Study is a multifaceted epidemiologic investigation of workers at six Department of Energy (DOE) facilities: Los Alamos, Rocky Flats, Mound, Savannah River, Oak Ridge, and Hanford. Information from a variety of record sources has been collected and abstracted for these studies. This report considers the accuracy of the demographic, occupational, and radiation exposure data collected for studies at Rocky Flats. the majority of the information was accurately abstracted, and analyses based on these data may be conducted

Preliminary siting activities for new waste handling facilities at the Idaho National Engineering Laboratory

Energy Technology Data Exchange (ETDEWEB)

Taylor, D.D.; Hoskinson, R.L.; Kingsford, C.O.; Ball, L.W.

1994-09-01

The Idaho Waste Processing Facility, the Mixed and Low-Level Waste Treatment Facility, and the Mixed and Low-Level Waste Disposal Facility are new waste treatment, storage, and disposal facilities that have been proposed at the Idaho National Engineering Laboratory (INEL). A prime consideration in planning for such facilities is the selection of a site. Since spring of 1992, waste management personnel at the INEL have been involved in activities directed to this end. These activities have resulted in the (a) identification of generic siting criteria, considered applicable to either treatment or disposal facilities for the purpose of preliminary site evaluations and comparisons, (b) selection of six candidate locations for siting,and (c) site-specific characterization of candidate sites relative to selected siting criteria. This report describes the information gathered in the above three categories for the six candidate sites. However, a single, preferred site has not yet been identified. Such a determination requires an overall, composite ranking of the candidate sites, which accounts for the fact that the sites under consideration have different advantages and disadvantages, that no single site is superior to all the others in all the siting criteria, and that the criteria should be assigned different weighing factors depending on whether a site is to host a treatment or a disposal facility. Stakeholder input should now be solicited to help guide the final selection. This input will include (a) siting issues not already identified in the siting, work to date, and (b) relative importances of the individual siting criteria. Final site selection will not be completed until stakeholder input (from the State of Idaho, regulatory agencies, the public, etc.) in the above areas has been obtained and a strategy has been developed to make a composite ranking of all candidate sites that accounts for all the siting criteria.

Preliminary siting activities for new waste handling facilities at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Taylor, D.D.; Hoskinson, R.L.; Kingsford, C.O.; Ball, L.W.

1994-09-01

The Idaho Waste Processing Facility, the Mixed and Low-Level Waste Treatment Facility, and the Mixed and Low-Level Waste Disposal Facility are new waste treatment, storage, and disposal facilities that have been proposed at the Idaho National Engineering Laboratory (INEL). A prime consideration in planning for such facilities is the selection of a site. Since spring of 1992, waste management personnel at the INEL have been involved in activities directed to this end. These activities have resulted in the (a) identification of generic siting criteria, considered applicable to either treatment or disposal facilities for the purpose of preliminary site evaluations and comparisons, (b) selection of six candidate locations for siting,and (c) site-specific characterization of candidate sites relative to selected siting criteria. This report describes the information gathered in the above three categories for the six candidate sites. However, a single, preferred site has not yet been identified. Such a determination requires an overall, composite ranking of the candidate sites, which accounts for the fact that the sites under consideration have different advantages and disadvantages, that no single site is superior to all the others in all the siting criteria, and that the criteria should be assigned different weighing factors depending on whether a site is to host a treatment or a disposal facility. Stakeholder input should now be solicited to help guide the final selection. This input will include (a) siting issues not already identified in the siting, work to date, and (b) relative importances of the individual siting criteria. Final site selection will not be completed until stakeholder input (from the State of Idaho, regulatory agencies, the public, etc.) in the above areas has been obtained and a strategy has been developed to make a composite ranking of all candidate sites that accounts for all the siting criteria

IFMIF : International Fusion Materials Irradiation Facility Conceptual Design Activity: Final report

International Nuclear Information System (INIS)

Martone, M.

1997-01-01

This report documents the results of the Conceptual Design Activity (CDA) on the International Fusion Materials Irradiation Facility (IFMIF), conducted during 1995 and 1996. The activity is under the auspices of the International Energy Agency (IEA) Implementing Agreement for a Programme of Research and Development on Fusion Materials. An IEA Fusion Materials Executive Subcommittee was charged with overseeing the IFMIF-CDA work. Participants in the CDA are the European Union, Japan, and the United States, with the Russian Federation as an associate member

IFMIF : International Fusion Materials Irradiation Facility Conceptual Design Activity: Final report

Energy Technology Data Exchange (ETDEWEB)

Martone, M [ENEA, Centro Ricerche Frascati, Rome (Italy)

1997-01-01

This report documents the results of the Conceptual Design Activity (CDA) on the International Fusion Materials Irradiation Facility (IFMIF), conducted during 1995 and 1996. The activity is under the auspices of the International Energy Agency (IEA) Implementing Agreement for a Programme of Research and Development on Fusion Materials. An IEA Fusion Materials Executive Subcommittee was charged with overseeing the IFMIF-CDA work. Participants in the CDA are the European Union, Japan, and the United States, with the Russian Federation as an associate member.

Computerized waste-accountability shipping and packaging system

International Nuclear Information System (INIS)

Jackson, J.A.; Baston, M. Jr.; DeVer, E.A.

1981-01-01

The Waste Accountability, Shipping and Packaging System (WASP) is a real-time computerized system designed and implemented by Mound Facility to meet the stringent packaging and reporting requirements of radioactive waste being shipped to burial sites. The system stores packaging data and inspection results for each unit and prepares all necessary documents at the time of shipment. Shipping data specific for each burial site are automatically prepared on magnetic tape for transmission to the computing center at that site. WASP has enabled Mound Facility to effectively meet the requirements of the burial sites, diminishing the possibility of being rejected from a site because of noncompliance

On the classification of active and passive seawater intrusion

Science.gov (United States)

Werner, A. D.

2017-12-01

Active and passive seawater intrusion (SWI) arise when the freshwater head gradient slopes downwards towards land and the sea, respectively. However, a third category exists (i.e., passive-active SWI), whereby active SWI occurs inland of a mound in piezometric surface, whereas passive SWI occurs on the seaward side of the mound. In this study, numerical modelling is used to characterize the three forms of SWI, including an overview of the transient features of active SWI. While only simple cross-sectional representations of coastal aquifer settings are considered, the analysis provides guidance on some of the key attributes of each SWI class, as an extension to previous SWI research that offers limited differentiation between the various SWI types. Threshold parameter combinations for the onset of each form of SWI are provided, as derived from sharp-interface, steady-state analytical solutions. Dispersive aspects of SWI are then explored using numerical simulation. Important differences between the various forms of SWI include the salinization of the watertable that occurs under active SWI and in the absence of recharge, and the formation of persistent freshwater lenses in aquifers experiencing active SWI but also subject to surface recharge. Attempts to characterize transient active SWI processes, in terms of buoyancy, advective and dispersive processes, using dimensionless ratios that are drawn from previous studies of steady-state SWI, highlight the complex, nonlinear relationships that govern active SWI, even for idealized circumstances.

Towards a Social History of Archaeology: The Case of the Excavators of Early Iron Age Burial Mounds in Southern Germany

Directory of Open Access Journals (Sweden)

Nils Müller-Scheessel

2008-05-01

Full Text Available While the general history of archaeology has received a growing interest lately1, these efforts still lack a common research-guiding agenda. Furthermore, most of the studies still concentrate on biographies and event history. The embedding of archaeology in the structures and conditions of its time is still a kind of terra incognita. The few well known publications (e. g. Hudson 1981; Kristiansen 1981; Patterson 1986; 1995 emphasize the gap only more. The lack of a significant amount of literature especially on the social history of archaeology is all the more surprising as the early interest in archaeology shows a clear social bias: archaeology was (and still is? a recreational activity for the educated and the well-off. While Hudson’s book in particular is very readable, it is clearly meant to provide only a very broad picture. Along with the other publications mentioned above it is now somewhat dated; the lack of recent works on this topic thus highlight the lack of interest in the social history of archaeology even more.2 However, this essay does not deal with this deplorable fact, but seeks to present some ‘hard’ data on only one, albeit important activity of early archaeological excavations, particularly those of burial mounds. Its focus is on Southern Germany and on graves from the early Iron Age.3

Use of urethane foam in preparing for decontamination and decommissioning of radioactive facilities

International Nuclear Information System (INIS)

1981-01-01

Portable urethane foam generating equipment has been in use for 15 to 20 years for a large number of applications, such as roof systems, tank insulation, and building insulation. Still another industrial application is its use in the decontamination and decommissioning of radioactive facilities at Mound Facility. The major problems encountered with urethane foams were with the packaging and stabilization procedures. The operation for spraying the foam on interior surfaces and equipment involved getting the gun inside without opening up the interior to the outside environment. A Gusmer FF proportioner and Model D spray gun was used for this operation. The gun was modified so that the trigger could be remotely located to facilitate its entry through a glovebox gloveport opening. The Model D gun has an air cap to blow foam off the tip of the gun. This cap was used to hold a plastic bag in place around the gun. The plastic bag is then put on a glove port and fastened securely. Urethane spray is applied on all exposed surfaces. This assures that all residual material is fixed for shipment. This simplifies cleaning operations as there is no need to remove the last trace of plutonium and results in a considerable shortening of the time required to prepare the gloveboxes. With the interior foamed, the gloveboxes are moved to the loading and packaging areas. Urethane foams are used to fill in the voids in our final shipping container. Radioactive waste materials are segregated according to the level of radioactive material present. One category is low level or low specific activity (LSA) and the other high level or Transuranic (TRU). Foam is used in TRU packages as packaging material to stabilize the loads and to help cushion against shock in transit on truck or railcar

Facility optimization to improve activation rate distributions during IVNAA

International Nuclear Information System (INIS)

Ebrahimi Khankook, Atiyeh; Rafat Motavalli, Laleh; Miri Hakimabad, Hashem

2013-01-01

Currently, determination of body composition is the most useful method for distinguishing between certain diseases. The prompt-gamma in vivo neutron activation analysis (IVNAA) facility for non-destructive elemental analysis of the human body is the gold standard method for this type of analysis. In order to obtain accurate measurements using the IVNAA system, the activation probability in the body must be uniform. This can be difficult to achieve, as body shape and body composition affect the rate of activation. The aim of this study was to determine the optimum pre-moderator, in terms of material for attaining uniform activation probability with a CV value of about 10% and changing the collimator role to increase activation rate within the body. Such uniformity was obtained with a high thickness of paraffin pre-moderator, however, because of increasing secondary photon flux received by the detectors it was not an appropriate choice. Our final calculations indicated that using two paraffin slabs with a thickness of 3 cm as a pre-moderator, in the presence of 2 cm Bi on the collimator, achieves a satisfactory distribution of activation rate in the body. (author)

IFMIF : International Fusion Materials Irradiation Facility Conceptual Design Activity: Executive summary

International Nuclear Information System (INIS)

1997-01-01

This report is a summary of the results of the Conceptual Design Activity (CDA) on the International Fusion Materials Irradiation Facility (IFMIF), conducted during 1995 and 1996. The activity is under the auspices of the International Energy Agency (IEA) Implementing Agreement for a Programme of Research and Development on Fusion Materials. An IEA Fusion Materials Executive Subcommittee was charged with overseeing the IFMIF-CDA work. Participants in the CDA are the European Union, Japan, and the United States, with the Russian Federation as an associate member

IFMIF : International Fusion Materials Irradiation Facility Conceptual Design Activity: Executive summary

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

This report is a summary of the results of the Conceptual Design Activity (CDA) on the International Fusion Materials Irradiation Facility (IFMIF), conducted during 1995 and 1996. The activity is under the auspices of the International Energy Agency (IEA) Implementing Agreement for a Programme of Research and Development on Fusion Materials. An IEA Fusion Materials Executive Subcommittee was charged with overseeing the IFMIF-CDA work. Participants in the CDA are the European Union, Japan, and the United States, with the Russian Federation as an associate member.

List of ERDA radioisotope (customers with summary of radioisotope shipments FY 1975

International Nuclear Information System (INIS)

Simmons, J.L.; Gano, S.R.

1976-01-01

The twelfth edition of the ERDA radioisotope customer list has been prepared at the request of the Division of Biomedical and Environmental Research. The purpose of this document is to list the FY 1975 commercial radioisotope production and distribution activities of USERDA facilities at Argonne National Laboratory, Battelle, Pacific Northwest Laboratories, Brookhaven National Laboratory, United Nuclear Inc., Idaho Operations Office, Hanford Engineering Development Laboratory, Mound Laboratory, Oak Ridge National Laboratory, and Savannah River Plant

Survey of active and inactive mines for possible use as in situ test facilities

International Nuclear Information System (INIS)

1976-09-01

A survey of active and inactive mines which might be useful for radioactive waste storage in situ test experiments was conducted. It was performed for Union Carbide Corporation, Nuclear Division, Office of Waste Isolation. The report covers available information gathered from literature, U.S. Bureau of Mines, the Mining Enforcement and Safety Agency, and a limited number of personal contacts with constructors or operators of facilities. This survey is preliminary in nature and the objective is to develop potential candidate facilities for in situ experiments which warrant further investigation. Included are descriptions of 244 facilities, with all the data about each one which was available within the time restraint of the study. These facility descriptions are additionally indexed by depth of mine, nature of the country rock, mineral mined, and type of entry. A total of 14 inactive mines and 34 active mines has been selected as those most worthy of further investigation for possible service as nuclear waste isolation test facilities. This investigation, being preliminary and having been performed in a very short time period, must be qualified, and the description of the qualification is presented in the body of this report. Qualifications deal primarily with the hazard of having omitted facilities and having incomplete data in some instances. Results indicate sedimentary rock mines of minerals of evaporite origin as a first ranking of preference for in situ testing, followed by other sedimentary rocks and then by mines producing minerals from any type rock where the mine is above the local water table. These are general rules and of course there can be exceptions to them

The association between high recreational physical activity and physical activity as a part of daily living in adolescents and availability of local indoor sports facilities and sports clubs

DEFF Research Database (Denmark)

Niclasen, B.; Petzold, M.; Schnohr, Christina Warrer

2012-01-01

Aim: The aim of this study was to examine how vigorous physical activity (recreational physical activity) (VPA) and moderate to vigorous physical activity as a part of daily life (MVPA) is associated with structural characteristics (availability of sports facilities and sports clubs with child...... facilities and of sports clubs with child members as independent variables, and adjusted for age, gender, family affluence (FAS), and type of habitation (capital, town or village). Results: High VPA increased with access to indoor facilities, while high MVPA was less likely (odds ratio (OR) 0.54 (0......, gender and FAS but positively associated if also adjusted for indoor sports facilities. Conclusions: Access to indoor sports facilities itself had a positive association with high VPA, but was persistently negatively associated with high MVPA. Presence of sports clubs with child members was positively...

IFMIF - International Fusion Materials Irradiation Facility Conceptual Design Activity/Interim Report

International Nuclear Information System (INIS)

Rennich, M.J.

1995-12-01

Environmental acceptability, safety, and economic viability win ultimately be the keys to the widespread introduction of fusion power. This will entail the development of radiation- resistant and low- activation materials. These low-activation materials must also survive exposure to damage from neutrons having an energy spectrum peaked near 14 MeV with annual radiation doses in the range of 20 displacements per atom (dpa). Testing of candidate materials, therefore, requires a high-flux source of high energy neutrons. The problem is that there is currently no high-flux source of neutrons in the energy range above a few MeV. The goal, is therefore, to provide an irradiation facility for use by fusion material scientists in the search for low-activation and damage-resistant materials. An accellerator-based neutron source has been established through a number of international studies and workshops' as an essential step for materials development and testing. The mission of the International Fusion Materials Irradiation Facility (IFMIF) is to provide an accelerator-based, deuterium-lithium (D-Li) neutron source to produce high energy neutrons at sufficient intensity and irradiation volume to test samples of candidate materials up to about a full lifetime of anticipated use in fusion energy reactors. would also provide calibration and validation of data from fission reactor and other accelerator-based irradiation tests. It would generate material- specific activation and radiological properties data, and support the analysis of materials for use in safety, maintenance, recycling, decommissioning, and waste disposal systems

Field test of plutonium and thorium contaminated clay soils from the Mound Site using the ACT*DE*CON Process

International Nuclear Information System (INIS)

Johnson, J.O.; Swift, N.A.; Church, R.H.; Neff, R.A.

1998-01-01

A treatability test was run during the summer and fall of 1997 to demonstrate the effectiveness of ACT*DE*CON for removing plutonium and thorium from the clay soils around Mound. ACT*DE*CON is a proprietary solution patented by Selentec. The process utilized a highly selective dissolution of the contaminants by the use of a chemical wash. The pilot scale process involved pretreatment of the soil in an attrition scrubber with ACT*DE*CON solution. This blended solution was then passed through a counter-current extraction chamber where additional contact with ACT*DE*CON solution occurred, followed by a rinse cycle. During this process sand was added to aid contact of the solution with the soil particles. The sand is removed during the rinse step and reused. The chelating agent is separated from the contaminant and recycled back into the process, along with the reverse osmosis permeate. The resulting solution can be further treated to concentrate the contaminant. Three different types of environmental soils were tested -- plutonium and thorium contaminated soils with the natural clay content, and plutonium contaminated soils with a high percentage of fine clay particles. The goal of these tests was to reduce the plutonium levels from several hundreds of pCi/g to between 25 and 75 pCi/g and the thorium from a couple hundred pCi/g to less than 5 pCi/g. The results of these four tests are presented along with a discussion of the operating parameters and the lessons learned relating to full scale implementation at Mound as well as other potential applications of this process

Measurements and FLUKA simulations of bismuth and aluminium activation at the CERN Shielding Benchmark Facility (CSBF)

Science.gov (United States)

Iliopoulou, E.; Bamidis, P.; Brugger, M.; Froeschl, R.; Infantino, A.; Kajimoto, T.; Nakao, N.; Roesler, S.; Sanami, T.; Siountas, A.

2018-03-01

The CERN High Energy AcceleRator Mixed field facility (CHARM) is located in the CERN Proton Synchrotron (PS) East Experimental Area. The facility receives a pulsed proton beam from the CERN PS with a beam momentum of 24 GeV/c with 5 ṡ1011 protons per pulse with a pulse length of 350 ms and with a maximum average beam intensity of 6.7 ṡ1010 p/s that then impacts on the CHARM target. The shielding of the CHARM facility also includes the CERN Shielding Benchmark Facility (CSBF) situated laterally above the target. This facility consists of 80 cm of cast iron and 360 cm of concrete with barite concrete in some places. Activation samples of bismuth and aluminium were placed in the CSBF and in the CHARM access corridor in July 2015. Monte Carlo simulations with the FLUKA code have been performed to estimate the specific production yields for these samples. The results estimated by FLUKA Monte Carlo simulations are compared to activation measurements of these samples. The comparison between FLUKA simulations and the measured values from γ-spectrometry gives an agreement better than a factor of 2.

Determination of Importance Evaluation for Exploratory Studies Facility (ESF) Subsurface Testing Activities

International Nuclear Information System (INIS)

Goodin, S.

2002-01-01

This Determination of Importance Evaluation (DIE) applies to the Subsurface Exploratory Studies Facility (ESF), encompassing the Topopah Spring (TS) Loop from Station 0+00 meters (m) at the North Portal to breakthrough at the South Portal (approximately 78+77 m), and ancillary test and operation support areas including the Enhanced Characterization of the Repository Block (ECRB) Cross Drift. This evaluation applies specifically to site characterization testing activities ongoing and planned in the Subsurface ESF. ESF site characterization activities are being performed to obtain the information necessary to determine whether the Yucca Mountain Site is suitable as a geologic repository for spent nuclear fuel and high-level radioactive waste. A more detailed description of these testing activities is provided in Section 6 of this DIE. Generally, the construction and operation of excavations associated with these testing activities are evaluated in the DIE for the Subsurface ESF (CRWMS M andO 1999a) and the DIE for the ESF ECRB Cross Drift (CRWMS M andO 2000a). The scope of this DIE also entails the proposed Unsaturated Zone (UZ) Transport Test at Busted Butte. Although, not a part of the TS Loop or ECRB Cross Drift, the associated testing activities are Subsurface testing activities. Busted Butte is located to the south south-east of the TS Loop and is outside the Conceptual Controlled Area Boundary (CCAB). These activities provide access to the Calico Hills (CH) geologic structure. In the case of Busted Butte, construction and operation of excavations are evaluated herein (since this activity was not previously evaluated in CRWMS M andO 1999a). The objectives of this DIE are to determine whether Subsurface ESF testing, and associated activities, could potentially impact site characterization testing and/or the waste isolation capabilities of the site. Controls needed to limit any potential impacts are identified in Section 13. The validity and veracity of the

Sociospatial distribution of access to facilities for moderate and vigorous intensity physical activity in Scotland by different modes of transport

Directory of Open Access Journals (Sweden)

Lamb Karen E

2012-07-01

Full Text Available Abstract Background People living in neighbourhoods of lower socioeconomic status have been shown to have higher rates of obesity and a lower likelihood of meeting physical activity recommendations than their more affluent counterparts. This study examines the sociospatial distribution of access to facilities for moderate or vigorous intensity physical activity in Scotland and whether such access differs by the mode of transport available and by Urban Rural Classification. Methods A database of all fixed physical activity facilities was obtained from the national agency for sport in Scotland. Facilities were categorised into light, moderate and vigorous intensity activity groupings before being mapped. Transport networks were created to assess the number of each type of facility accessible from the population weighted centroid of each small area in Scotland on foot, by bicycle, by car and by bus. Multilevel modelling was used to investigate the distribution of the number of accessible facilities by small area deprivation within urban, small town and rural areas separately, adjusting for population size and local authority. Results Prior to adjustment for Urban Rural Classification and local authority, the median number of accessible facilities for moderate or vigorous intensity activity increased with increasing deprivation from the most affluent or second most affluent quintile to the most deprived for all modes of transport. However, after adjustment, the modelling results suggest that those in more affluent areas have significantly higher access to moderate and vigorous intensity facilities by car than those living in more deprived areas. Conclusions The sociospatial distributions of access to facilities for both moderate intensity and vigorous intensity physical activity were similar. However, the results suggest that those living in the most affluent neighbourhoods have poorer access to facilities of either type that can be reached on foot

Dispersion and activity patterns of three populations of large termite ...

African Journals Online (AJOL)

Ventilation shafts are numerous on large, unshaded mounds of M. subhyalinus, confirming the main purpose of the shafts, which may however limit the maximum size of mounds. M. michaelseni, which has no external openings, uses a different system for ventilation. Flighting by Macrotermes alates shows interesting ...

Facility Effluent Monitoring Plan for Pacific Northwest National Laboratory Balance-of-Plant Facilities

International Nuclear Information System (INIS)

Ballinger, M.Y.; Shields, K.D.

1999-01-01

The Pacific Northwest National Laboratory (PNNL) operates a number of research and development (R and D) facilities for the Department of Energy on the Hanford Site. According to DOE Order 5400.1, a Facility Effluent Monitoring Plan is required for each site, facility, or process that uses, generates, releases, or manages significant pollutants or hazardous materials. Three of the R and D facilities: the 325, 331, and 3720 Buildings, are considered major emission points for radionuclide air sampling and thus individual Facility Effluent Monitoring Plans (FEMPs) have been developed for them. Because no definition of ''significant'' is provided in DOE Order 5400.1 or the accompanying regulatory guide DOE/EH-0173T, this FEMP was developed to describe monitoring requirements in the DOE-owned, PNNL-operated facilities that do not have individual FEMPs. The remainder of the DOE-owned, PNNL-operated facilities are referred to as Balance-of-Plant (BOP) facilities. Activities in the BOP facilities range from administrative to laboratory and pilot-scale R and D. R and D activities include both radioactive and chemical waste characterization, fluid dynamics research, mechanical property testing, dosimetry research, and molecular sciences. The mission and activities for individual buildings are described in the FEMP

Facility Effluent Monitoring Plan for Pacific Northwest National Laboratory Balance-of-Plant Facilities

Energy Technology Data Exchange (ETDEWEB)

Ballinger, M.Y.; Shields, K.D.

1999-04-02

The Pacific Northwest National Laboratory (PNNL) operates a number of research and development (R and D) facilities for the Department of Energy on the Hanford Site. According to DOE Order 5400.1, a Facility Effluent Monitoring Plan is required for each site, facility, or process that uses, generates, releases, or manages significant pollutants or hazardous materials. Three of the R and D facilities: the 325, 331, and 3720 Buildings, are considered major emission points for radionuclide air sampling and thus individual Facility Effluent Monitoring Plans (FEMPs) have been developed for them. Because no definition of ''significant'' is provided in DOE Order 5400.1 or the accompanying regulatory guide DOE/EH-0173T, this FEMP was developed to describe monitoring requirements in the DOE-owned, PNNL-operated facilities that do not have individual FEMPs. The remainder of the DOE-owned, PNNL-operated facilities are referred to as Balance-of-Plant (BOP) facilities. Activities in the BOP facilities range from administrative to laboratory and pilot-scale R and D. R and D activities include both radioactive and chemical waste characterization, fluid dynamics research, mechanical property testing, dosimetry research, and molecular sciences. The mission and activities for individual buildings are described in the FEMP.

25 CFR Appendix A to Subpart G - List of Activities Eligible for Funding Under BIA Transportation Facility Maintenance Program

Science.gov (United States)

2010-04-01

... Transportation Facility Maintenance Program A Appendix A to Subpart G Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAND AND WATER INDIAN RESERVATION ROADS PROGRAM BIA Road Maintenance Pt. 170... Transportation Facility Maintenance Program The following activities are eligible for BIA Transportation Facility...

Facility effluent monitoring plan for the 327 Facility

International Nuclear Information System (INIS)

1994-11-01

The 327 Facility [Post-Irradiation Testing Laboratory] provides office and laboratory space for Pacific Northwest Laboratory (PNL) scientific and engineering staff conducting multidisciplinary research in the areas of post-irradiated fuels and structural materials. The facility is designed to accommodate the use of radioactive and hazardous materials in the conduct of these activities. This report summarizes the airborne emissions and liquid effluents and the results of the Facility Effluent Monitoring Plan (FEMP) determination for the facility. The complete monitoring plan includes characterization of effluent streams, monitoring/sampling design criteria, a description of the monitoring systems and sample analysis, and quality assurance requirements

Liquid Effluent Retention Facility/Effluent Treatment Facility Hazards Assessment

International Nuclear Information System (INIS)

Simiele, G.A.

1994-01-01

This document establishes the technical basis in support of Emergency Planning activities for the Liquid Effluent Retention Facility and Effluent Treatment Facility the Hanford Site. The document represents an acceptable interpretation of the implementing guidance document for DOE ORDER 5500.3A. Through this document, the technical basis for the development of facility specific Emergency Action Levels and the Emergency Planning Zone is demonstrated

Interdisciplinary landscape research in a medieval mound in one of the oldest Dutch towns, Vlaardingen, the Netherlands

Science.gov (United States)

de Ridder, Tim; Kluiving, Sjoerd; van Dasselaar, Marcel

2013-04-01

In Medieval times the city of Vlaardingen (the Netherlands) was strategically located on the confluence of three rivers, the Meuse, the Merwede and the Vlaarding. A church of early 8th century was already located here. In a short period of time Vlaardingen developed into an international trading place, the most important place in the former county of Holland. Starting from the 11th century the river Meuse threatened to flood the settlement, and as a reaction to it inhabitants started to raise the surface. This resulted eventually in an enormous mound, surface: 200 by 250 meter, built up in a four to five meter thick sequence of clay and manure in which organic rests of former occupation are extremely well preserved, e.g. wooden posts, mesh walls, but also leather objects. Early 2002 graves were found in the city centre, dating 1000-1050, in which not only the wooden coffins, but also the straw that covered the deceased. In human teeth DNA appeared to be well preserved, classified as the oldest in the nation, turning the church hill into a large database of human DNA. To secure the future of this vulnerable soil archive currently an extensive interdisciplinary research (mechanical drilling, grain size, TGA, archeological remains, osteology, hydrology, dating methods, micromorphology, microfauna, molluscs, diatoms) has started in 2011 to gain knowledge on the internal structure of the mound as well as on the well-preserved nature of the archaeological evidence. In this presentation the results of this large-scale project are demonstrated in a number of cross-sections with interrelated geological and archaeological stratification. Results of GSA (including end-member analysis EMMA), TGA, XRF and micromorphology analyses are presented. Distinction between natural and anthropogenic layering is made on the occurrence of chemical elements phosphor and potassium. Results of this research are also applied in the construction of the 3D model of the subsurface (this session

Very Low Activity Waste Disposal Facility Recently Commissioned as an Extension of El Cabril LILW Disposal Facility in Spain

International Nuclear Information System (INIS)

Zuloaga, P.; Navarro, M.

2009-01-01

This paper describes the Very Low Activity Radioactive Waste (VLLW) disposal facility, designed, built and operated by ENRESA as a part of El Cabril LILW disposal facility. El Cabril facility was commissioned in 1992 and has 28 concrete vaults with an internal volume of 100,000 m 3 , as well as waste treatment systems and waste characterization laboratories. The total needs identified in Spain for LILW disposal are of some 176,000 m 3 , of which around 120,000 m3 might be classified as VLLW This project was launched in 2003 and the major licensing steps have been town planning license (2003), construction authorization (after Environmental Impact Statement and report from Nuclear Safety Council-CSN, 2006), and Operations Authorization (after report from CSN, July 2008). The new VLLW disposal facility has a capacity for 130,000 meters cube in four disposal cells of approximately the same size. Only the first cell has been built. The design of the barriers is based on the European Directive for elimination of dangerous waste and consists of a clay layer 1 m, 3 cm geo-bentonite films, and 4 mm HDPE film. In order to minimize leachate volumes collected and help a good monitoring of the site, each cell is divided into different sections, which are protected during operation -before placing a provisional HDPE capping- by a light shelter and where leachate collection is segregated from other sections. (authors)

Calibration of the delayed-gamma neutron activation facility

International Nuclear Information System (INIS)

Ma, R.; Zhao, X.; Rarback, H.M.; Yasumura, S.; Dilmanian, F.A.; Moore, R.I.; Lo Monte, A.F.; Vodopia, K.A.; Liu, H.B.; Economos, C.D.; Nelson, M.E.; Aloia, J.F.; Vaswani, A.N.; Weber, D.A.; Pierson, R.N. Jr.; Joel, D.D.

1996-01-01

The delayed-gamma neutron activation facility at Brookhaven National Laboratory was originally calibrated using an anthropomorphic hollow phantom filled with solutions containing predetermined amounts of Ca. However, 99% of the total Ca in the human body is not homogeneously distributed but contained within the skeleton. Recently, an artificial skeleton was designed, constructed, and placed in a bottle phantom to better represent the Ca distribution in the human body. Neutron activation measurements of an anthropomorphic and a bottle (with no skeleton) phantom demonstrate that the difference in size and shape between the two phantoms changes the total body calcium results by less than 1%. To test the artificial skeleton, two small polyethylene jerry-can phantoms were made, one with a femur from a cadaver and one with an artificial bone in exactly the same geometry. The femur was ashed following the neutron activation measurements for chemical analysis of Ca. Results indicate that the artificial bone closely simulates the real bone in neutron activation analysis and provides accurate calibration for Ca measurements. Therefore, the calibration of the delayed-gamma neutron activation system is now based on the new bottle phantom containing an artificial skeleton. This change has improved the accuracy of measurement for total body calcium. Also, the simple geometry of this phantom and the artificial skeleton allows us to simulate the neutron activation process using a Monte Carlo code, which enables us to calibrate the system for human subjects larger and smaller than the phantoms used as standards. copyright 1996 American Association of Physicists in Medicine

Diatomite-immobilized BiOI hybrid photocatalyst: Facile deposition synthesis and enhanced photocatalytic activity

International Nuclear Information System (INIS)

Li, Baoying; Huang, Hongwei; Guo, Yuxi; Zhang, Yihe

2015-01-01

Graphical abstract: - Highlights: • A novel diatomite-immobilized BiOI hybrid photocatalyst has been prepared by a facile one-step deposition process for the first time. • The diatomite-immobilized BiOI hybrid photocatalyst exhibits much better photocatalytic performance. • This enhancement should be attributed to that diatomite can play as an excellent carrier platform to increase the reactive sites and promote the separation of photogenerated electron–hole pairs. • This work shed new light on facile fabrication of novel composite photocatalyst based on natural mineral. - Abstract: A novel diatomite-immobilized BiOI hybrid photocatalyst has been prepared by a facile one-step deposition process for the first time. The structure, morphology and optical property of the products were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and UV–vis diffuse reflectance spectroscopy (DRS). The photocatalytic performance of the as-prepared BiOI/diatomite photocatalysts was studied by photodegradation of Rhodamine B (RhB) and methylene blue (MB) and monitoring photocurrent generation under visible light (λ > 420 nm). The results revealed that BiOI/diatomite composites exhibit enhanced photocatalytic activity compared to the pristine BiOI sample. This enhancement should be attributed to that diatomite can play as an excellent carrier platform to increase the reactive sites and promote the separation of photogenerated electron–hole pairs. In addition, the corresponding photocatalytic mechanism was proposed based on the active species trapping experiments. This work shed new light on facile fabrication of novel composite photocatalyst based on natural mineral.

Diatomite-immobilized BiOI hybrid photocatalyst: Facile deposition synthesis and enhanced photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Li, Baoying; Huang, Hongwei, E-mail: hhw@cugb.edu.cn; Guo, Yuxi; Zhang, Yihe, E-mail: zyh@cugb.edu.cn

2015-10-30

Graphical abstract: - Highlights: • A novel diatomite-immobilized BiOI hybrid photocatalyst has been prepared by a facile one-step deposition process for the first time. • The diatomite-immobilized BiOI hybrid photocatalyst exhibits much better photocatalytic performance. • This enhancement should be attributed to that diatomite can play as an excellent carrier platform to increase the reactive sites and promote the separation of photogenerated electron–hole pairs. • This work shed new light on facile fabrication of novel composite photocatalyst based on natural mineral. - Abstract: A novel diatomite-immobilized BiOI hybrid photocatalyst has been prepared by a facile one-step deposition process for the first time. The structure, morphology and optical property of the products were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and UV–vis diffuse reflectance spectroscopy (DRS). The photocatalytic performance of the as-prepared BiOI/diatomite photocatalysts was studied by photodegradation of Rhodamine B (RhB) and methylene blue (MB) and monitoring photocurrent generation under visible light (λ > 420 nm). The results revealed that BiOI/diatomite composites exhibit enhanced photocatalytic activity compared to the pristine BiOI sample. This enhancement should be attributed to that diatomite can play as an excellent carrier platform to increase the reactive sites and promote the separation of photogenerated electron–hole pairs. In addition, the corresponding photocatalytic mechanism was proposed based on the active species trapping experiments. This work shed new light on facile fabrication of novel composite photocatalyst based on natural mineral.

Growth of a Hydrate Mound in the Sea of Japan over 300 ka as Revealed by U-Th Ages of MDAC and by H2S Concentrations of Massive Hydrates

Science.gov (United States)

Matsumoto, R.; Snyder, G. T.; Hiruta, A.; Kakizaki, Y.; Huang, C. Y.; Shen, C. C.

2017-12-01

The geological and geophysical exploration of gas hydrate in the Sea of Japan has revealed that hydrates occur as thick massive deposits within gas chimneys which often give rise to pingo-like hydrate mounds on the seafloor. We examine one case in which LWD has demonstrated anomalous profiles including both very low natural gamma ray (<10 API) and high acoustic velocities (2.5 to 3.5 km/s) extending down to 120mbsf, the base of gas hydrate stability (BGHS)[1]. Both conventional and pressure coring have confirmed thick, massive deposits of pure-gas hydrates. Hydrates in the shallow subsurface (< 20mbsf) are characterized by high H2S concentrations corresponding to AOM-induced production of HS-. The deeper hydrates generally have negligible amounts of H2S, with occasional exceptions in which H2S is moderately high. These observations lead us to conclude that both the re-equilibration and growth of hydrates in high CH4 and low to zero H2S conditions has continued during burial, and that this ongoing growth is an essential processes involved in the development of massive hydrates in the Sea of Japan.Regardless of depth, the Japan Sea gas hydrates are closely associated with 13-C depleted, methane-derived authigenic carbonates (MDACs). These MDACs are considered to have been formed at near-SMT depths as a response to increased alkalinity caused by AOM and, as such, MDACs are assumed to represent approximate paleo-seafloor at times of enhanced methane flux and intensive accumulation of gas hydrate in shallow subsurface. U-Th ages of MDACs collected from various depths in a mound-chimney system in central Joetsu Spur have revealed that the paleo-seafloor of 300 ka is presently situated at 30 to 55 mbsf within the gas chimney, in contrast to off-mound sites where it is situated at 100 mbsf. This suggests that at 300 ka the mound stood as a "hydrate-pingo" of 70 m high relative to the surrounding sea floor. At this time, the BGHS shoaled upwards 10m due to eustatic sea

Use of a Graded Approach in the Application of the Management System Requirements for Facilities and Activities

International Nuclear Information System (INIS)

2014-06-01

IAEA Safety Standards Series No. GS-R-3, The Management System for Facilities and Activities, defines the requirements for establishing, implementing, assessing and continually improving a management system that integrates safety, health, environmental, security, quality and economical elements. It details the need to grade the application of the management system requirements to ensure that resources are deployed and appropriate controls are applied on the basis of the consideration of: the significance and complexity of each product or activity; the hazards and the magnitude of the potential impact (risks) associated with the safety, health, environmental, security, quality and economical elements of each product or activity; and the possible consequences if a product fails or an activity is carried out incorrectly. The grading of the application of the requirements detailed in IAEA Safety Standards Series No. GS-R-3 is especially essential when they are implemented in smaller facilities and activities. The grading is done to ensure that the management system for smaller facilities and activities are suitably tailored to the hazards and the magnitude of the potential impact of the facilities and activities. Detailed guidance on how the grading requirements of IAEA Safety Standards Series No. GS-R-3 can be met and how to ensure that grading is performed in a consistent manner can be found in IAEA Safety Standards Series No. GS-G-3.1, Application of the Management System for Facilities and Activities. In addition, it contains guidance on systematic grading methods which will reduce the likelihood and consequences of improper grading. This publication provides an overview of grading fundamentals, the grading process, the role of classification in the process and the typical controls that can be graded. It also provides practical guidance and examples of grading as required by IAEA Safety Standards Series No. GS-R-3 to develop and apply a method of grading

100 mg 251Cf activation analysis facility at the Savannah River Laboratory

International Nuclear Information System (INIS)

MacMurdo, K.W.; Bowman, W.W.

1975-01-01

The 252 Cf Activation Analysis Facility at the Savannah River Laboratory (SRL) is used routinely for multielement analyses of a wide variety of solid and liquid samples (e.g., metal alloys, fly ash and other airborne particles, rocks, and aqueous and nonaqueous solutions). An automated absolute activation analysis technique, developed to use neutron transport codes to calculate multienergy group neutron spectra and fluxes, converts counting data directly into elemental concentrations expressed in parts per million. The facility contains four sources of 252 Cf totaling slightly over 100 mg. A pneumatic ''rabbit'' system permits automatic irradiation/decay/counting regimes to be performed unattended on up to 100 samples. Detection sensitivities of less than or equal to 400 ppb natural uranium and less than or equal to 0.5 nCi/g for 239 Pu are observed. Detection limits for over 65 elements have been determined. Over 40 elements are detectable at the one part per million level or less. Overall accuracies of +- 10 percent are observed for most elements. (auth)

List of DOE radioisotope customers with summary of radioisotope shipments, FY 1979

International Nuclear Information System (INIS)

Burlison, J.S.

1980-06-01

The fifteenth edition of the radioisotope customer list was prepared at the request of the Division of Financial Services, Office of the Assistant Secretary for Environment, Department of Energy (DOE). This document lists DOE's radioisotope production and distribution activities by its facilities at Argonne National Laboratory; Pacific Northwest Laboratory; Brookhaven National Laboratory; Hanford Engineering Development Laboratory; Idaho Operations Office; Los Alamos Scientific Laboratory; Mound Facility; Oak Ridge National Laboratory; Rocky Flats Area Office; Savannah River Laboratory; and UNC Nuclear Industries, Inc. The information is divided into five sections: Isotope suppliers, facility, contracts and isotopes or services supplied; alphabetical list of customers, and isotopes purchased; alphabetical list of isotopes cross-referenced to customer numbers; geographical location of radioisotope customers; and radioisotope sales and transfers-FY 1979

List of DOE radioisotope customers with summary of radioisotope shipments, FY 1981

International Nuclear Information System (INIS)

Burlison, J.S.

1982-09-01

The seventeenth edition of the radioisotope customer list was prepared at the request of the Office of Health and Environmental Research, Office of Energy Research, Department of Energy (DOE). This document lists DOE's radioisotope production and distribution activities by its facilities at Argonne National Laboratory: Pacific Northwest Laboratory; Brookhaven National Laboratory; Hanford Engineering Development Laboratory; Idaho Operations Office; Los Alamos Scientific Laboratory; Mound Facility; Oak Ridge National Laboratory; Savannah River Laboratory; and UNC Nuclear Industries, Inc. The information is divided into five sections: (1) isotope suppliers, facility, contracts and isotopes or services supplied; (2) alphabetical list of customers, and isotopes purchased; (3) alphabetical list of isotopes cross-referenced to customer numbers; (4) geographical location of radioisotope customers; and (5) radioisotope sales and transfers-FY 1980

List of DOE radioisotope customers with summary of radioisotope shipments, FY 1980

International Nuclear Information System (INIS)

Burlison, J.S.

1981-08-01

The sixteenth edition of the radioisotope customer list was prepared at the request of the Office of Health and Environmental Research, Office of energy Research, Department of Energy (DOE). This document lists DOE's radioisotope production and distribution activities by its facilities at Argonne National Laboratory; Pacific Northwest Laboratory; Brookhaven National Laboraory; Hanford Engineering Development Laboratory; Idaho Operations Office; Los Alamos Scientific Laboratory; Mound Facility; Oak Ridge National Laboratory; Savannah River Laboratory; and UNC Nuclear Industries, Inc. The information is divided into five sections: (1) isotope suppliers, facility, contracts and isotopes or services supplied; (2) alphabetical list of customers, and isotopes purchased; (3) alphabetical list of isotopes cross-referenced to customer numbers; (4) geographical location of radioisotope customers; and (5) radioisotope sales and transfers-FY 1980

Chemical characteristics of hydrothermal fluids from the TAG Mound of the Mid-Atlantic Ridge in August 1994: Implications for spatial and temporal variability of hydrothermal activity

Science.gov (United States)

Gamo, Toshitaka; Chiba, Hitoshi; Masuda, Harue; Edmonds, Henrietta N.; Fujioka, Kantaro; Kodama, Yukio; Nanba, Hiromi; Sano, Yuji

The TAG hydrothermal mound on the Mid-Atlantic Ridge (26°08‧N, 44°50‧W) was revisited in August 1994 with the submersible Shinkai 6500 in order to characterize time-series fluid chemistry prior to the ODP drilling. Fluid samples were taken from both black smokers and white smokers. Si, pH, alkalinity, H2S, major cations (Na+, K+, Ca2+, Mg2+), major anions (Cl-, SO42-), and minor elements (Li, Sr, B, Fe, Mn, Cu, Zn, Br) as well as Sr isotope ratios were measured. We report the first Br/Cl ratios for the TAG hydrothermal fluids, showing no fractionation between Br and Cl during the fluid-rock interaction. This study shows small changes in composition of the black smoker fluids from the 1990 data (Edmond et al., 1995). Changes of pH, alkalinity, Fe, K, and 87Sr/86Sr values are suggestive of subsurface FeS precipitation and a decrease of water/rock ratio at a deeper reaction zone. Differences in chemical characteristics between the black and white smoker fluids were similarly observed as in 1990.

Determination of Importance Evaluation for Exploratory Studies Facility (ESF) Subsurface Testing Activities

International Nuclear Information System (INIS)

C.J. Byrne

2001-01-01

This Determination of Importance Evaluation (DIE) applies to the Subsurface Exploratory Studies Facility (ESF), encompassing the Topopah Spring (TS) Loop from Station 0+00 meters (m) at the North Portal to breakthrough at the South Portal (approximately 78+77 m), and ancillary test and operation support areas including the Enhanced Characterization of the Repository Block (ECRB) Cross Drift. This evaluation applies specifically to site characterization testing activities ongoing and planned in the Subsurface ESF. ESF site characterization activities are being performed to obtain the information necessary to determine whether the Yucca Mountain Site is suitable as a geologic repository for spent nuclear fuel and high-level radioactive waste. A more detailed description of these testing activities is provided in Section 6 of this DIE. Generally, the construction and operation of excavations associated with these testing activities are evaluated in the DIE for the Subsurface ESF (CRWMS M and O 1999a) and the DIE for the ESF ECRB Cross Drift (CRWMS M and O 2000a). The scope of this DIE also entails the proposed Unsaturated Zone (UZ) Transport Test at Busted Butte. Although, not a part of the TS Loop or ECRB Cross Drift, the associated testing activities are Subsurface testing activities. Busted Butte is located to the south south-east of the TS Loop and is outside the Conceptual Controlled Area Boundary (CCAB). These activities provide access to the Calico Hills (CH) geologic structure. In the case of Busted Butte, construction and operation of excavations are evaluated herein (since this activity was not previously evaluated in CRWMS M and O 1999a). The objectives of this DIE are to determine whether Subsurface ESF testing, and associated activities, could potentially impact site characterization testing and/or the waste isolation capabilities of the site. Controls needed to limit any potential impacts are identified in Section 13. The validity and veracity of the

Determination of Importance Evaluation for Exploratory Studies Facility (ESF) Subsurface Testing Activities

Energy Technology Data Exchange (ETDEWEB)

C.J. Byrne

2001-02-20

This Determination of Importance Evaluation (DIE) applies to the Subsurface Exploratory Studies Facility (ESF), encompassing the Topopah Spring (TS) Loop from Station 0+00 meters (m) at the North Portal to breakthrough at the South Portal (approximately 78+77 m), and ancillary test and operation support areas including the Enhanced Characterization of the Repository Block (ECRB) Cross Drift. This evaluation applies specifically to site characterization testing activities ongoing and planned in the Subsurface ESF. ESF site characterization activities are being performed to obtain the information necessary to determine whether the Yucca Mountain Site is suitable as a geologic repository for spent nuclear fuel and high-level radioactive waste. A more detailed description of these testing activities is provided in Section 6 of this DIE. Generally, the construction and operation of excavations associated with these testing activities are evaluated in the DIE for the Subsurface ESF (CRWMS M&O 1999a) and the DIE for the ESF ECRB Cross Drift (CRWMS M&O 2000a). The scope of this DIE also entails the proposed Unsaturated Zone (UZ) Transport Test at Busted Butte. Although, not a part of the TS Loop or ECRB Cross Drift, the associated testing activities are Subsurface testing activities. Busted Butte is located to the south south-east of the TS Loop and is outside the Conceptual Controlled Area Boundary (CCAB). These activities provide access to the Calico Hills (CH) geologic structure. In the case of Busted Butte, construction and operation of excavations are evaluated herein (since this activity was not previously evaluated in CRWMS M&O 1999a). The objectives of this DIE are to determine whether Subsurface ESF testing, and associated activities, could potentially impact site characterization testing and/or the waste isolation capabilities of the site. Controls needed to limit any potential impacts are identified in Section 13. The validity and veracity of the individual

Battle Mound: Exploring space, place, and history of a Red River Caddo community in southwest Arkansas

Science.gov (United States)

McKinnon, Duncan Paul

This research is a synthesis of archaeogeophysical and archaeohistorical data collected from the Battle Mound site (3LA1). Using these data, this research seeks to understand how the site is organized in terms of architectural variability and how differential use areas, such as domestic or community space, can be compared to ethnographic and archaeological data concerning Caddo community structure and landscape use. The research is formulated around three research questions related to spatial organization and settlement patterning, intrasite behavioral practices, and Caddo culture history. Results show that an examination at multiple scales of resolution can inform about the spatial organization and settlement patterning of Caddo communities and how these underlying principles that define space have endured or been modified over time. It also proposes a new intrasite model that can be productively tested with geophysical methods and the mapping of the distribution of features within large village areas.

Decommissioning engineering systems for nuclear facilities and knowledge inheritance for decommissioning of nuclear facilities

International Nuclear Information System (INIS)

Tachibana, Mitsuo

2016-01-01

Information on construction, operation and maintenance of a nuclear facility is essential in order to plan and implement the decommissioning of the nuclear facility. A decommissioning engineering system collects these information efficiently, retrieves necessary information rapidly, and support to plan the reasonable decommissioning as well as the systematic implementation of dismantling activities. Then, knowledge of workers involved facility operation and dismantling activities is important because decommissioning of nuclear facility will be carried out for a long period. Knowledge inheritance for decommissioning has been carried out in various organizations. This report describes an outline of and experiences in applying decommissioning engineering systems in JAEA and activities related to knowledge inheritance for decommissioning in some organizations. (author)

A study on the influence of the regulatory requirements of a nuclear facility during decommissioning activities

Energy Technology Data Exchange (ETDEWEB)

Park, Hee Seong; Park, Seung Kook; Park, Kook Nam; Hong, Yun Jeong; Park, Jang Jin; Choi, Jong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

The preliminary decommissioning plan should be written with various chapters such as a radiological characterization, a decommissioning strategy and methods, a design for decommissioning usability, a safety evaluation, decontamination and dismantling activities, radioactive waste management, an environmental effect evaluation, and fire protection. The process requirements of the decommissioning project and the technical requirements and technical criteria should comply with regulatory requirements when dismantling of a nuclear facility. The requirements related to safety in the dismantling of a nuclear facility refer to the IAEA safety serious. The present paper indicates that a decommissioning design and plan, dismantling activities, and a decommissioning project will be influenced by the decommissioning regulatory requirements when dismantling of a nuclear facility. We hereby paved the way to find the effect of the regulatory requirements on the decommissioning of a whole area from the decommissioning strategy to the radioactive waste treatment when dismantling a nuclear facility. The decommissioning requirements have a unique feature in terms of a horizontal relationship as well as a vertical relationship from the regulation requirements to the decommissioning technical requirements. The decommissioning requirements management will be conducted through research that can recognize a multiple relationship in the next stage.

Diatomite-immobilized BiOI hybrid photocatalyst: Facile deposition synthesis and enhanced photocatalytic activity

Science.gov (United States)

Li, Baoying; Huang, Hongwei; Guo, Yuxi; Zhang, Yihe

2015-10-01

A novel diatomite-immobilized BiOI hybrid photocatalyst has been prepared by a facile one-step deposition process for the first time. The structure, morphology and optical property of the products were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and UV-vis diffuse reflectance spectroscopy (DRS). The photocatalytic performance of the as-prepared BiOI/diatomite photocatalysts was studied by photodegradation of Rhodamine B (RhB) and methylene blue (MB) and monitoring photocurrent generation under visible light (λ > 420 nm). The results revealed that BiOI/diatomite composites exhibit enhanced photocatalytic activity compared to the pristine BiOI sample. This enhancement should be attributed to that diatomite can play as an excellent carrier platform to increase the reactive sites and promote the separation of photogenerated electron-hole pairs. In addition, the corresponding photocatalytic mechanism was proposed based on the active species trapping experiments. This work shed new light on facile fabrication of novel composite photocatalyst based on natural mineral.

Naturally occurring workplace facilities to increase the leisure time physical activity of workers: A propensity-score weighted population study

OpenAIRE

Aviroop Biswas; Peter M. Smith; Monique A.M. Gignac

2018-01-01

The benefit of providing access to physical activity facilities at or near work to support the leisure time physical activity (LTPA) of workers is uncertain. We examined the association between access to physical activity facilities at or near work and the LTPA of workers after adjusting for a range of individual and occupational characteristics. Data was obtained from 60,650 respondents to the 2007–2008 Canadian Community Health Survey. Participants were employed adults ≥18 years of age who ...

Wageningen UR Unmanned Aerial Remote Sensing Facility - Overview of activities

Science.gov (United States)

Bartholomeus, Harm; Keesstra, Saskia; Kooistra, Lammert; Suomalainen, Juha; Mucher, Sander; Kramer, Henk; Franke, Jappe

2016-04-01

To support environmental management there is an increasing need for timely, accurate and detailed information on our land. Unmanned Aerial Systems (UAS) are increasingly used to monitor agricultural crop development, habitat quality or urban heat efficiency. An important reason is that UAS technology is maturing quickly while the flexible capabilities of UAS fill a gap between satellite based and ground based geo-sensing systems. In 2012, different groups within Wageningen University and Research Centre have established an Unmanned Airborne Remote Sensing Facility. The objective of this facility is threefold: a) To develop innovation in the field of remote sensing science by providing a platform for dedicated and high-quality experiments; b) To support high quality UAS services by providing calibration facilities and disseminating processing procedures to the UAS user community; and c) To promote and test the use of UAS in a broad range of application fields like habitat monitoring, precision agriculture and land degradation assessment. The facility is hosted by the Laboratory of Geo-Information Science and Remote Sensing (GRS) and the Department of Soil Physics and Land Management (SLM) of Wageningen University together with the team Earth Informatics (EI) of Alterra. The added value of the Unmanned Aerial Remote Sensing Facility is that compared to for example satellite based remote sensing more dedicated science experiments can be prepared. This includes for example higher frequent observations in time (e.g., diurnal observations), observations of an object under different observation angles for characterization of BRDF and flexibility in use of camera's and sensors types. In this way, laboratory type of set ups can be tested in a field situation and effects of up-scaling can be tested. In the last years we developed and implemented different camera systems (e.g. a hyperspectral pushbroom system, and multispectral frame cameras) which we operated in projects all

The Management System for Facilities and Activities. Safety Requirements

International Nuclear Information System (INIS)

2011-01-01

This publication establishes requirements for management systems that integrate safety, health, security, quality assurance and environmental objectives. A successful management system ensures that nuclear safety matters are not dealt with in isolation but are considered within the context of all these objectives. The aim of this publication is to assist Member States in establishing and implementing effective management systems that integrate all aspects of managing nuclear facilities and activities in a coherent manner. It details the planned and systematic actions necessary to provide adequate confidence that all these requirements are satisfied. Contents: 1. Introduction; 2. Management system; 3. Management responsibility; 4. Resource management; 5. Process implementation; 6. Measurement, assessment and improvement.

Development of lithium target system in engineering validation and engineering design activity of the international fusion materials irradiation facility (IFMIF/EVEDA)

International Nuclear Information System (INIS)

Wakai, Eiichi; Kondo, Hiroo; Sugimoto, Masayoshi; Ida, Mizuho; Kanemura, Takuji; Watanabe, Kazuyoshi; Fujishiro, Kouji; Edao, Yuuki; Niitsuma, Shigeto; Kimura, Haruyuki; Fukada, Satoshi; Hiromoto, Tetsushi; Shigeharu, Satoshi; Yagi, Jyuro; Furukawa, Tomohiro; Hirakawa, Yasushi; Suzuki, Akihiro; Terai, Takayuki; Horiike, Hiroshi; Hoashi, Eiji; Suzuki, Sachiko; Yamaoka, Nobuo; Serizawa, Hisashi; Kawahito, Yosuke; Tsuji, Yoshiyuki; Furuya, Kazuyuki; Takeo, Fumio

2012-01-01

Engineering validation and engineering design activity (EVEDA) for the international fusion materials irradiation facility (IFMIF) has been conducted since 2007. Research and development of the Lithium target facility is an important part of this activity. We constructed a world largest liquid Lithium test loop with a capacity of 5000 L in 2010 and successfully completed the first stage validation tests (functional tests of components and Lithium flow test (flow velocity 15 m/s at the target). In the present article, recent results of the EVEDA activity for the Lithium target facility and related technologies on liquid Lithium are reviewed. (author)

The Role Of Land Use In Environmental Decision Making At Three DOE Mega-Cleanup Sites, Fernald, Rocky Flats, and Mound

International Nuclear Information System (INIS)

Jewett, M.A.

2011-01-01

This paper explores the role that future land use decisions have played in the establishment of cost-effective cleanup objectives and the setting of environmental media cleanup levels for the three major U.S. Department of Energy (DOE) sites for which cleanup has now been successfully completed: the Rocky Flats, Mound, and Fernald Closure Sites. At each site, there are distinct consensus-building histories throughout the following four phases: (1) the facility shut-down and site investigation phase, which took place at the completion of their Cold War nuclear-material production missions; (2) the decision-making phase, whereby stakeholder and regulatory-agency consensus was achieved for the future land-use-based environmental decisions confronting the sites; (3) the remedy selection phase, whereby appropriate remedial actions were identified to achieve the future land-use-based decisions; and (4) the implementation phase, whereby the selected remedial actions for these high-profile sites were implemented and successfully closed out. At each of the three projects, there were strained relationships and distrust between the local community and the DOE as a result of site contamination and potential health effects to the workers and local residents. To engage citizens and interested stakeholder groups - particularly in the role of final land use in the decision-making process, the site management teams at each respective site developed new public-participation strategies to open stakeholder communication channels with site leadership, technical staff, and the regulatory agencies. This action proved invaluable to the success of the projects and reaching consensus on appropriate levels of cleanup. With the implementation of the cleanup remedies now complete, each of the three DOE sites have become models for future environmental-remediation projects and associated decision making.

List of ERDA radioisotope customers with summary of radioisotope shipments, FY 1976

International Nuclear Information System (INIS)

Simmons, J.L.

1977-03-01

The thirteenth edition of the ERDA radioisotope customer list has been prepared at the request of the Office of Program Coordination, Office of the Assistant Administrator. The purpose of the document is to list the FY 1976 commercial radioisotope production and distribution activities of ERDA facilities at Argonne National Laboratory, Battelle, Pacific Northwest Laboratories, Brookhaven National Laboratory, Hanford Engineering Development Laboratory, Idaho Operations Office, Los Alamos Scientific Laboratory, Mound Laboratory, Oak Ridge National Laboratory, Savannah River Laboratory, and United Nuclear Industries, Inc

Activity measurements at a waste volume reduction facility

International Nuclear Information System (INIS)

Richardson, J.; Lee, D.A.

1979-01-01

The monitoring program for Ontario Hydro's radioactive waste management site will be described, several aspects of which will be discussed in detail. The program at this facility includes categorization, volume reduction processing, and storage of solid radioactive wastes from nuclear generating stations of the CANDU type. At the present time, two types of volume reduction process are in operation - incineration and compaction. Following categorization and processing, wastes are stored in in-ground concrete trenches or tile-holes, or in above-ground quadricells. The monitoring program is divided into three areas: public safety, worker safety, and structural integrity. Development projects with respect to the monitoring program have been undertaken to achieve activity accounting for the total waste management program. In particular, a field measurement for the radioactivity content of radioactive ash containers and compacted waste drums

Halmokhoz fűződő történeti és hiedelemmondák a Közép-Tiszántúlon - Historical Legends and Superstitions about the Mounds of the Middle-Transtisza Region

Directory of Open Access Journals (Sweden)

BEDE, Ádám

2014-09-01

Full Text Available The world of myths and legends about the mounds of the Great Hungarian Plain is unbelievably rich. This article discusses the ancient mounds (especially the ‘kurgans’ in the area of the Körös-Maros National Park Directorate and in the Transtisza Region of Csongrád County and in Békés County. The population of this area was always intrigued by questions about the mounds, such as what they hide inside or who they were built by. Human imagination has kept the mysterious stories alive, though many legends or details have been lost, deformed or transformed during the centuries. In spite of the fact that the oral tradition of the Ottoman era is full of mysterious elements, such as castles, tunnels, buried treasure, dragons, shaman-priests (‘táltos’ and witches, the stories were frequently based on historical facts. In the present article, the most beautiful and most interesting pieces of these myths are cited. Our aim was to present one or two examples of every myth-category, in order to give an overall picture about the folklore of the region. We quote most of these stories word for word, so as to honour the informants and the sources and to reveal the unique atmosphere of these tales.

Overview of the applications of cement-based immobilization technologies developed at US DOE facilities

International Nuclear Information System (INIS)

Dole, L.R.

1985-01-01

This paper briefly reviews seven cement-based waste form development programs at six of the US Department of Energy (DOE) sites. These sites have developed a variety of processes that range from producing 25-mm-(1-in.-) diam pellets in a glove box to producing 240-m-(800-ft-) diam grout sheets within the bedding planes of a deep shale formation. These successful applications of cement-based waste forms to the many radioactive waste streams from nuclear facilities bear witness to the flexibility and reliability of this class of immobilization materials. The US DOE sites and their programs are: (1) Oak Ridge National Laboratory (ORNL), Hydrofracture Grout; (2) Hanford, Transportable Grout Facility (TGF); (3) Savannah River Plant (SRP), Nitrate Saltcrete; (4) EG and G Idaho, Process Experimental Pilot Plant (PREPP); (5) Mound Laboratory (ML), Waste Pelletization Process; (6) ORNL, FUETAP Concretes, and (7) Rocky Flats Plant (RFP), Inert Carrier Concrete Process (ICCP). The major issues regarding the application of cement-based waste forms to radioactive waste management problems are also presented. These issues are (1) leachability, (2) radiation stability, (3) thermal stability, (4) phase complexity of the matrix, and (5) effects of the waste stream composition. A cursory review of current research in each of these areas is included along with a discussion of future trends in cement-based waste form developments and applications. 35 refs., 12 figs

Synthesis of sulfonated porous carbon nanospheres solid acid by a facile chemical activation route

Energy Technology Data Exchange (ETDEWEB)

Chang, Binbin, E-mail: changbinbin806@163.com; Guo, Yanzhen; Yin, Hang; Zhang, Shouren; Yang, Baocheng, E-mail: baochengyang@yahoo.com

2015-01-15

Generally, porous carbon nanospheres materials are usually prepared via a template method, which is a multi-steps and high-cost strategy. Here, we reported a porous carbon nanosphere solid acid with high surface area and superior porosity, as well as uniform nanospheical morphology, which prepared by a facile chemical activation with ZnCl{sub 2} using resorcinol-formaldehyde (RF) resins spheres as precursor. The activation of RF resins spheres by ZnCl{sub 2} at 400 °C brought high surface area and large volume, and simultaneously retained numerous oxygen-containing and hydrogen-containing groups due to the relatively low processing temperature. The presence of these functional groups is favorable for the modification of –SO{sub 3}H groups by a followed sulfonation treating with sulphuric acid and organic sulfonic acid. The results of N{sub 2} adsorption–desorption and electron microscopy clearly showed the preservation of porous structure and nanospherical morphology. Infrared spectra certified the variation of surface functional groups after activation and the successful modification of –SO{sub 3}H groups after sulfonation. The acidities of catalysts were estimated by an indirect titration method and the modified amount of –SO{sub 3}H groups were examined by energy dispersive spectra. The results suggested sulfonated porous carbon nanospheres catalysts possessed high acidities and –SO{sub 3}H densities, which endowed their significantly catalytic activities for biodiesel production. Furthermore, their excellent stability and recycling property were also demonstrated by five consecutive cycles. - Graphical abstract: Sulfonated porous carbon nanospheres with high surface area and superior catalytic performance were prepared by a facile chemical activation route. - Highlights: • Porous carbon spheres solid acid prepared by a facile chemical activation. • It owns high surface area, superior porosity and uniform spherical morphology. • It possesses

The MOVE study: a study protocol for a randomised controlled trial assessing interventions to maximise attendance at physical activity facilities.

Science.gov (United States)

Newton, Joshua D; Klein, Ruth; Bauman, Adrian; Newton, Fiona J; Mahal, Ajay; Gilbert, Kara; Piterman, Leon; Ewing, Michael T; Donovan, Robert J; Smith, Ben J

2015-04-18

Physical activity is associated with a host of health benefits, yet many individuals do not perform sufficient physical activity to realise these benefits. One approach to rectifying this situation is through modifying the built environment to make it more conducive to physical activity, such as by building walking tracks or recreational physical activity facilities. Often, however, modifications to the built environment are not connected to efforts aimed at encouraging their use. The purpose of the Monitoring and Observing the Value of Exercise (MOVE) study is to evaluate the effectiveness of two interventions designed to encourage the ongoing use of a new, multi-purpose, community-based physical activity facility. A two-year, randomised controlled trial with yearly survey points (baseline, 12 months follow-up, 24 months follow-up) will be conducted among 1,300 physically inactive adult participants aged 18-70 years. Participants will be randomly assigned to one of three groups: control, intervention 1 (attendance incentives), or intervention 2 (attendance incentives and tailored support following a model based on customer relationship management). Primary outcome measures will include facility usage, physical activity participation, mental and physical wellbeing, community connectedness, social capital, friendship, and social support. Secondary outcome measures will include stages of change for facility usage and social cognitive decision-making variables. This study will assess whether customer relationship management systems, a tool commonly used in commercial marketing settings, can encourage the ongoing use of a physical activity facility. Findings may also indicate the population segments among which the use of such systems are most effective, as well as their cost-effectiveness. Australian New Zealand Clinical Trials Registry: ACTRN12615000012572 (registered 9 January 2015).

Monitoring the performances of a real scale municipal solid waste composting and a biodrying facility using respiration activity indices.

Science.gov (United States)

Evangelou, Alexandros; Gerassimidou, Spyridoula; Mavrakis, Nikitas; Komilis, Dimitrios

2016-05-01