WorldWideScience

Sample records for month annealing cycle

  1. Transformation behaviors of Ti_(48.5)Ni_(48)Fe_2Nb_(1.5) dependence of annealing and thermomechanical cycling

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    The effect of annealing treatments and thermomechanical cycling on the transformation behaviors and shape memory effect of Ti48.5Ni48Fe2Nb1.5 shape memory alloys were investigated using electrical resistivity measurement and tensile testing. It is found that the transformation behaviors are influenced considerably by the annealing treatments. Both Ms and As increase with increasing annealing temperature and cooling rate. Martensite stabilization occurs during thermomechanical cycles, thus resulting in lower...

  2. Influence of Annealing Time and Thermo-Mechanical Cycling on Constrained Recovery Properties of a Cold-Worked NiTi Wire

    Science.gov (United States)

    Yan, Xiaojun; Ge, Yuli; Van Humbeeck, Jan

    2017-02-01

    In this work, the influence of parameters such as annealing time, pre-strain and thermo-mechanical cycling on recovery stresses of NiTi wires has been investigated by using a dynamic mechanical analyzer. The results show that the maximum recovery stress decreases with increasing annealing time and increases with increasing pre-strain except for 60-min annealed sample with 4% pre-strain, which has a higher recovery stress than 45-min annealed sample with the same pre-strain. The recovery stresses drastically increase during the first two thermo-mechanical cycles for all samples, regardless of annealing time. The observed changes of recovery stress could be attributed to different transformation temperatures and mechanical properties induced by different annealing times and/or thermo-mechanical cycling.

  3. Classification of German business cycles using monthly data

    OpenAIRE

    Heilemann, Ullrich; Münch, Heinz Josef

    2001-01-01

    The recent renaissance of business cycle analysis has led to a renewed interest in business cycle classification as pioneered by Burns/Mitchell, Spiethoff and resumed in the seventies by Meyer/Weinberg (1975a, b). The rather successful elaboration and test of a “modern” four-phase classification scheme for the United States and West Germany by Meyer/Weinberg motivated the present authors to develop such a classification scheme for West Germany. Based on a kind of stylised facts it should help...

  4. Fuel Cycle Research & Development Technical Monthly - May 2012

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Michael C. [Los Alamos National Laboratory

    2012-06-28

    Management and Integration LANL - Initial coordination meetings with NE and NA-20 were held the first week of May. Additional meetings, to include NA-82 and the new Proliferation and Terrorism Risk Assessment task are scheduled for June. Work package planning as part of the NTD transition is ongoing. Microcalorimetry LANL - Some parts to attempt repair of a malfunctioning water chiller that has been holding up work on the current detector array have arrived. We will attempt to begin running the compressor/cryostat next week to resume work on commissioning the detector array. We have also been working on a backup plan to temporarily move our system to a different lab space. Completed data analysis and prepared a paper summarizing Pu measurements for peer-review journal. Two members of our team presented work at the SORMA West 2012 conference. Completed data analysis and prepared a milestone report summarizing the development of Monte Carlo tools to study systematic errors. Electrochemical Sensor INL - The second sensor test was stopped short due to the work stand-down. Some activities related to this work have resumed, but not all. The sensor used during the second test was removed from the furnace and it showed cracks and later crumbled when being rinsed for sample preparation. The sensor material will be submitted to SEM analysis once work is resumed in the facilities where analysis is performed. A third sensor test has started. Tests with different arrangements will continue and will be oriented based on post-test analysis of the first three sensor tests. Materials with different annealing temperatures will also be prepared for analysis. Lead slowing down spectrometer LANL - Continued work on perturbation method for LSDS analysis. We are running simulations to delineate issues and are checking additional data libraries to see whether there are differences in simulation results. Electrochemical sensor INL - The second sensor test was stopped short due to the work

  5. Prediction of the smoothed monthly mean sunspot numbers for solar cycle 24

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The prediction for the smoothed monthly mean sunspot numbers (hereafter SMSNs) of solar cycle 23, which was given with a similar cycle method proposed by us at the beginning time of cycle 23, is analyzed and verified in this paper. Using our predicted maximum SMSN and the ascending length for solar cycle 24, and as- suming their relative errors to be respectively 20% and ± 7 months, solar cycles 2, 4, 8, 11, 17, 20 and 23 are selected to be the similar cycles to cycle 24. The selected solar cycles are divided into two groups. The first group consists of all the selected cycles; while the second group consists of only cycles 11, 17, 20 and 23. Two SMSN time profiles then may be obtained, respectively, for the two similar cycle groups. No significant difference is found between the two predicted time profiles. Consid- ering the latest observed sunspot number so far available for cycle 23 and the pre- dictions for the minimum SMSN of cycle 24, a date calibration is done for the ob- tained time profiles, and thus, SMSNs for 127 months of cycle 24, from October 2007 to April 2018, are predicted.

  6. Prediction of the smoothed monthly mean sunspot numbers for solar cycle 24

    Institute of Scientific and Technical Information of China (English)

    WANG JiaLong; MIAO Juan; LIU SiQing; GONG JianCun; ZHU CuiLian

    2008-01-01

    The prediction for the smoothed monthly mean sunspot numbers (hereafter SMSNs) of solar cycle 23,which was given with a similar cycle method proposed by us at the beginning time of cycle 23,is analyzed and verified in this paper.Using our predicted maximum SMSN and the ascending length for solar cycle 24,and assuming their relative errors to be respectively 20% and ± 7 months,solar cycles 2,4,8,11,17,20 and 23 are selected to be the similar cycles to cycle 24.The selected solar cycles are divided into two groups.The first group consists of all the selected cycles; while the second group consists of only cycles 11,17,20 and 23.Two SMSN time profiles then may be obtained,respectively,for the two similar cycle groups.No significant difference is found between the two predicted time profiles.Considering the latest observed sunspot number so far available for cycle 23 and the predictions for the minimum SMSN of cycle 24,a date calibration is done for the obtained time profiles,and thus,SMSNs for 127 months of cycle 24,from October 2007 to April 2018,are predicted.

  7. Extending Depot Length and Intervals for DDG 51 Class Ships: Examining the 72 Month Operational Cycle

    Science.gov (United States)

    2016-01-01

    model that was used in examining the effect of a 72-month cycle on the Arleigh Burke– class destroyer fleet. Chap- ter Seven presents our findings...in improving ship class maintenance management through work package documentation development. They also recognized SURFMEPP’s role in tracking work...Extending Depot Length and Intervals for DDG-51- Class Ships Examining the 72-Month Operational Cycle Roland J. Yardley, Daniel Tremblay, Brian

  8. Sensitivity of Amazonian TOA flux diurnal cycle composite monthly variability to choice of reanalysis

    Science.gov (United States)

    Dodson, J. Brant; Taylor, Patrick C.

    2016-05-01

    Amazonian deep convection experiences a strong diurnal cycle driven by the cycle in surface sensible heat flux, which contributes to a significant diurnal cycle in the top of the atmosphere (TOA) radiative flux. Even when accounting for seasonal variability, the TOA flux diurnal cycle varies significantly on the monthly timescale. Previous work shows evidence supporting a connection between variability in the convective and radiative cycles, likely modulated by variability in monthly atmospheric state (e.g., convective instability). The hypothesized relationships are further investigated with regression analysis of the radiative diurnal cycle and atmospheric state using additional meteorological variables representing convective instability and upper tropospheric humidity. The results are recalculated with three different reanalyses to test the reliability of the results. The radiative diurnal cycle sensitivity to upper tropospheric humidity is about equal in magnitude to that of convective instability. In addition, the results are recalculated with the data subdivided into the wet and dry seasons. Overall, clear-sky radiative effects have a dominant role in radiative diurnal cycle variability during the dry season. Because of this, even in a convectively active region, the clear-sky radiative effects must be accounted for in order to fully explain the monthly variability in diurnal cycle. Finally, while there is general agreement between the different reanalysis-based results when examining the full data time domain (without regard to time of year), there are significant disagreements when the data are divided into wet and dry seasons. The questionable reliability of reanalysis data is a major limitation.

  9. Intermixing of InGaAs/GaAs Quantum Well Using Multiple Cycles Annealing Cu-doped SiO2

    Energy Technology Data Exchange (ETDEWEB)

    Hongpinyo, V; Ding, Y H; Dimas, C E; Wang, Y; Ooi, B S; Qiu, W; Goddard, L L; Behymer, E M; Cole, G D; Bond, T C

    2008-06-11

    The authors investigate the effect of intermixing in InGaAs/GaAs quantum well structure using Cu-doped SiO{sub 2}. The incorporation of Cu into the silica film yields larger bandgap shift than typical impurity-free vacancy diffusion (IFVD) method at a lower activation temperature. We also observe enhancement of the photoluminescence (PL) signal from the intermixed InGaAs/GaAs quantum well structure after being cycle-annealed at 850 C.

  10. Covariability in the Monthly Mean Convective and Radiative Diurnal Cycles in the Amazon

    Science.gov (United States)

    Dodson, Jason B.; Taylor, Patrick C.

    2015-01-01

    The diurnal cycle of convective clouds greatly influences the radiative energy balance in convectively active regions of Earth, through both direct presence, and the production of anvil and stratiform clouds. Previous studies show that the frequency and properties of convective clouds can vary on monthly timescales as a result of variability in the monthly mean atmospheric state. Furthermore, the radiative budget in convectively active regions also varies by up to 7 Wm-2 in convectively active regions. These facts suggest that convective clouds connect atmospheric state variability and radiation variability beyond clear sky effects alone. Previous research has identified monthly covariability between the diurnal cycle of CERES-observed top-of-atmosphere radiative fluxes and multiple atmospheric state variables from reanalysis over the Amazon region. ASVs that enhance (reduce) deep convection, such as CAPE (LTS), tend to shift the daily OLR and cloud albedo maxima earlier (later) in the day by 2-3 hr. We first test the analysis method using multiple reanalysis products for both the dry and wet seasons to further investigate the robustness of the preliminary results. We then use CloudSat data as an independent cloud observing system to further evaluate the relationships of cloud properties to variability in radiation and atmospheric states. While CERES can decompose OLR variability into clear sky and cloud effects, it cannot determine what variability in cloud properties lead to variability in the radiative cloud effects. Cloud frequency, cloud top height, and cloud microphysics all contribute to the cloud radiative effect, all of which are observable by CloudSat. In addition, CloudSat can also observe the presence and variability of deep convective cores responsible for the production of anvil clouds. We use these capabilities to determine the covariability of convective cloud properties and the radiative diurnal cycle.

  11. An estimate of monthly global emissions of anthropogenic CO2: Impact on the seasonal cycle of atmospheric CO2

    Energy Technology Data Exchange (ETDEWEB)

    Erickson, D [Oak Ridge National Laboratory (ORNL); Mills, R [Oak Ridge National Laboratory (ORNL); Gregg, J [University of Maryland; Blasing, T J [ORNL; Hoffman, F [Oak Ridge National Laboratory (ORNL); Andres, Robert Joseph [ORNL; Devries, M [Oak Ridge National Laboratory (ORNL); Zhu, Z [NASA Goddard Space Flight Center; Kawa, S [NASA Goddard Space Flight Center

    2008-01-01

    Monthly estimates of the global emissions of anthropogenic CO2 are presented. Approximating the seasonal CO2 emission cycle using a 2-harmonic Fourier series with coefficients as a function of latitude, the annual fluxes are decomposed into monthly flux estimates based on data for the United States and applied globally. These monthly anthropogenic CO2 flux estimates are then used to model atmospheric CO2 concentrations using meteorological fields from the NASA GEOS-4 data assimilation system. We find that the use of monthly resolved fluxes makes a significant difference in the seasonal cycle of atmospheric CO2 in and near those regions where anthropogenic CO2 is released to the atmosphere. Local variations of 2-6 ppmv CO2 in the seasonal cycle amplitude are simulated; larger variations would be expected if smaller source-receptor distances could be more precisely specified using a more refined spatial resolution. We also find that in the midlatitudes near the sources, synoptic scale atmospheric circulations are important in the winter and that boundary layer venting and diurnal rectifier effects are more important in the summer. These findings have implications for inverse-modeling efforts that attempt to estimate surface source/sink regions especially when the surface sinks are colocated with regions of strong anthropogenic CO2 emissions.

  12. Influence of homo-buffer layers and post-deposition rapid thermal annealing upon atomic layer deposition grown ZnO at 100 °C with three-pulsed precursors per growth cycle

    Science.gov (United States)

    Cheng, Yung-Chen; Yuan, Kai-Yun; Chen, Miin-Jang

    2017-10-01

    ZnO main epilayers are deposited with three-pulsed precursors in every growth cycle at 100 °C on various thicknesses of 300 °C-grown homo-buffer layers by atomic layer deposition (ALD) on sapphire substrate. Samples are treated without and with post-deposition rapid thermal annealing (RTA). Two different annealing temperatures 300 and 1000 °C are utilized in the ambience of oxygen for 5 min. Extremely low background electron concentration 8.4 × 1014 cm-3, high electron mobility 62.1 cm2/V s, and pronounced enhancement of near bandgap edge photoluminescence (PL) are achieved for ZnO main epilayer with sufficient thickness of buffer layer (200 ALD cycles) and post-deposition RTA at 1000 °C. Effective block and remove of thermally unstable mobile defects and other crystal lattice imperfections are the agents of quality promotion of ZnO thin film.

  13. New heating schedule in hydrogen annealing furnace based on process simulation for less energy consumption

    Energy Technology Data Exchange (ETDEWEB)

    Saboonchi, Ahmad [Department of Mechanical Engineering, Isfahan University of Technology, Isfahan 84154 (Iran); Hassanpour, Saeid [Rayan Tahlil Sepahan Co., Isfahan Science and Technology Town, Isfahan 84155 (Iran); Abbasi, Shahram [R and D Department, Mobarakeh Steel Complex, Isfahan (Iran)

    2008-11-15

    Cold rolled steel coils are annealed in batch furnaces to obtain desirable mechanical properties. Annealing operations involve heating and cooling cycles which take long due to high weight of the coils under annealing. To reduce annealing time, a simulation code was developed that is capable of evaluating more effective schedules for annealing coils during the heating process. This code is additionally capable of accurate determination of furnace turn-off time for different coil weights and charge dimensions. After studying many heating schedules and considering heat transfer mechanism in the annealing furnace, a new schedule with the most advantages was selected as the new operation conditions in the hydrogen annealing plant. The performance of all the furnaces were adjusted to the new heating schedule after experiments had been carried out to ensure the accuracy of the code and the fitness of the new operation condition. Comparison of similar yield of cold rolled coils over two months revealed that specific energy consumption of furnaces under the new heating schedule decreased by 11%, heating cycle time by 16%, and the hydrogen consumption by 14%. (author)

  14. On the Relationship between Solar Wind Speed, Earthward-Directed Coronal Mass Ejections, Geomagnetic Activity, and the Sunspot Cycle Using 12-Month Moving Averages

    Science.gov (United States)

    Wilson, Robert M.; Hathaway, David H.

    2008-01-01

    For 1996 .2006 (cycle 23), 12-month moving averages of the aa geomagnetic index strongly correlate (r = 0.92) with 12-month moving averages of solar wind speed, and 12-month moving averages of the number of coronal mass ejections (CMEs) (halo and partial halo events) strongly correlate (r = 0.87) with 12-month moving averages of sunspot number. In particular, the minimum (15.8, September/October 1997) and maximum (38.0, August 2003) values of the aa geomagnetic index occur simultaneously with the minimum (376 km/s) and maximum (547 km/s) solar wind speeds, both being strongly correlated with the following recurrent component (due to high-speed streams). The large peak of aa geomagnetic activity in cycle 23, the largest on record, spans the interval late 2002 to mid 2004 and is associated with a decreased number of halo and partial halo CMEs, whereas the smaller secondary peak of early 2005 seems to be associated with a slight rebound in the number of halo and partial halo CMEs. Based on the observed aaM during the declining portion of cycle 23, RM for cycle 24 is predicted to be larger than average, being about 168+/-60 (the 90% prediction interval), whereas based on the expected aam for cycle 24 (greater than or equal to 14.6), RM for cycle 24 should measure greater than or equal to 118+/-30, yielding an overlap of about 128+/-20.

  15. A 12-month clinical investigation with a 24-day regimen containing 15 microg ethinylestradiol plus 60 microg gestodene with respect to hemostasis and cycle control.

    Science.gov (United States)

    Fruzzetti, F; Genazzani, A R; Ricci, C; De Negri, F; Bersi, C; Carmassi, F

    2001-06-01

    The effects of a 24-day regimen containing 15 microg ethinyl estradiol (EE) plus 60 microg gestodene on cycle control and on hemostasis, were evaluated in 58 healthy women (age 19-47 years). All women received the pill for 12 months. Withdrawal bleeding at every cycle during the tablet-free interval was experienced by 84.5% of the women. The overall incidence of irregular bleedings was 19.3%. Hemostasis was evaluated in 20 women. No changes in plasma fibrinogen concentrations, nor in prothrombin fragment F1+2 were observed. A slight increase in thrombin-antithrombin III complexes was observed after 6 and 12 months of oral contraceptive use. Antithrombin III activity significantly increased after one-year of pill intake. The concentrations of tissue plasminogen activator and plasminogen activator inhibitor, both antigen and activity, did not change. These results show that very low doses of EE, such as 15 microg, do not impair hemostasis in healthy females. However, the reduction for the EE dose is responsible of some of the effects on cycle control.

  16. Effect of prolonged annealing on the performance of coaxial Ge gamma-ray detectors

    NARCIS (Netherlands)

    Owens, A.; Brandenburg, S.; Buis, E. -J.; Kozorezov, A. G.; Kraft, S.; Ostendorf, R. W.; Quarati, F.

    2007-01-01

    The effects of prolonged annealing at elevated temperatures have been investigated in a 53 cm(3) closed-end coaxial high purity germanium detector in the reverse electrode configuration. The detector was multiply annealed at 100 degrees C in block periods of 7 days. After each anneal cycle it was co

  17. Evaluation of Helping Babies Breathe Quality Improvement Cycle (HBB-QIC) on retention of neonatal resuscitation skills six months after training in Nepal.

    Science.gov (United States)

    Kc, Ashish; Wrammert, Johan; Nelin, Viktoria; Clark, Robert B; Ewald, Uwe; Peterson, Stefan; Målqvist, Mats

    2017-04-11

    Each year 700,000 infants die due to intrapartum-related complications. Implementation of Helping Babies Breathe (HBB)-a simplified neonatal resuscitation protocol in low-resource clinical settings has shown to reduce intrapartum stillbirths and first-day neonatal mortality. However, there is a lack of evidence on the effect of different HBB implementation strategies to improve and sustain the clinical competency of health workers on bag-and-mask ventilation. This study was conducted to evaluate the impact of multi-faceted implementation strategy for HBB, as a quality improvement cycle (HBB-QIC), on the retention of neonatal resuscitation skills in a tertiary hospital of Nepal. A time-series design was applied. The multi-faceted intervention for HBB-QIC included training, daily bag-and-mask skill checks, preparation for resuscitation before every birth, self-evaluation and peer review on neonatal resuscitation skills, and weekly review meetings. Knowledge and skills were assessed through questionnaires, skill checklists, and Objective Structured Clinical Examinations (OSCE) before implementation of the HBB-QIC, immediately after HBB training, and again at 6 months. Means were compared using paired t-tests, and associations between skill retention and HBB-QIC components were analyzed using logistic regression analysis. One hundred thirty seven health workers were enrolled in the study. Knowledge scores were higher immediately following the HBB training, 16.4 ± 1.4 compared to 12.8 ± 1.6 before (out of 17), and the knowledge was retained 6 months after the training (16.5 ± 1.1). Bag-and-mask skills improved immediately after the training and were retained 6 months after the training. The retention of bag-and-mask skills was associated with daily bag-and-mask skill checks, preparation for resuscitation before every birth, use of a self-evaluation checklist, and attendance at weekly review meetings. The implementation strategies with the highest association to skill

  18. Intraseasonal characterization of tropospheric O3 in the North of the Buenos Aires Province: determining four months cycle and teleconnection evidence

    CERN Document Server

    Cionco, Rodolfo G; Quaranta, Nancy; Agosta, Eduardo

    2013-01-01

    Tropospheric ozone (O3T) is a secondary pollutant whose formation involved primarily solar radiation, NOx and volatile organic compounds. The North of the Buenos Aires Province has great agricultural-industrial activity; therefore, O3T study is an important issue in the area. In this paper, we present the first results tend to estimate and characterize O3T in San Nicol\\'as de los Arroyos, North of Buenos Aires. Due to a lack of in situ data, we analyse the observations of the instrument OMI (Ozone Monitoring Instrument) of land remote sensing satellite AURA (GSFC/NASA). The data cover the years 2004-2013. Applying the multitaper technique (MTM), very suitable for short and noisy data series, spectral analysis is performed on a grid corresponding 1{\\deg} in latitude by 1.5{\\deg} in longitude, centred South of the Province of Santa Fe. The most remarkable result is the emergence of a significant peak (95%) of four months cycle. To test the validity of this signal in San Nicol\\'as, daily solar radiation data (Q)...

  19. Skin physiology in microgravity: a 3-month stay aboard ISS induces dermal atrophy and affects cutaneous muscle and hair follicles cycling in mice.

    Science.gov (United States)

    Neutelings, Thibaut; Nusgens, Betty V; Liu, Yi; Tavella, Sara; Ruggiu, Alessandra; Cancedda, Ranieri; Gabriel, Maude; Colige, Alain; Lambert, Charles

    2015-01-01

    The Mice Drawer System (MDS) Tissue Sharing program was the longest rodent space mission ever performed. It provided 20 research teams with organs and tissues collected from mice having spent 3 months on the International Space Station (ISS). Our participation to this experiment aimed at investigating the impact of such prolonged exposure to extreme space conditions on mouse skin physiology. Mice were maintained in the MDS for 91 days aboard ISS (space group (S)). Skin specimens were collected shortly after landing for morphometric, biochemical, and transcriptomic analyses. An exact replicate of the experiment in the MDS was performed on ground (ground group (G)). A significant reduction of dermal thickness (-15%, P=0.05) was observed in S mice accompanied by an increased newly synthetized procollagen (+42%, P=0.03), likely reflecting an increased collagen turnover. Transcriptomic data suggested that the dermal atrophy might be related to an early degradation of defective newly formed procollagen molecules. Interestingly, numerous hair follicles in growing anagen phase were observed in the three S mice, validated by a high expression of specific hair follicles genes, while only one mouse in the G controls showed growing hairs. By microarray analysis of whole thickness skin, we observed a significant modulation of 434 genes in S versus G mice. A large proportion of the upregulated transcripts encoded proteins related to striated muscle homeostasis. These data suggest that a prolonged exposure to space conditions may induce skin atrophy, deregulate hair follicle cycle, and markedly affect the transcriptomic repertoire of the cutaneous striated muscle panniculus carnosus.

  20. Precise annealing of focal plane arrays for optical detection

    Energy Technology Data Exchange (ETDEWEB)

    Bender, Daniel A.

    2015-09-22

    Precise annealing of identified defective regions of a Focal Plane Array ("FPA") (e.g., exclusive of non-defective regions of the FPA) facilitates removal of defects from an FPA that has been hybridized and/or packaged with readout electronics. Radiation is optionally applied under operating conditions, such as under cryogenic temperatures, such that performance of an FPA can be evaluated before, during, and after annealing without requiring thermal cycling.

  1. Cognitive functions of regularly cycling women may differ throughout the month, depending on sex hormone status; A possible explanation to conflicting results of studies of ADHD in females.

    Directory of Open Access Journals (Sweden)

    Ronit eHaimov-Kochman

    2014-04-01

    Full Text Available Attention Deficit/Hyperactivity Disorder (ADHD is considered as a model of neuro-developmental cognitive function. ADHD research previously studied mainly males. A major biological distinction between the genders is the presence of a menstrual cycle, which is associated with variations in sex steroid hormone levels. There is a growing body of literature showing that sex hormones have the ability to regulate intracellular signaling systems that are thought to be abnormal in ADHD. Thus, it is conceivable to believe that this functional interaction between sex hormones and molecules involved with synaptic plasticity and neurotransmitter systems may be associated with some of the clinical characteristics of women with ADHD. In spite of the impact of sex hormones on major neurotransmitter systems of the brain in a variety of clinical settings, the menstrual cycle is usually entered to statistical analyses as a nuisance or controlled for by only testing male samples. Evaluation of brain structure, function and chemistry over the course of the menstrual cycle as well as across the lifespan of women (premenarche, puberty, cycling period, premenopause, postmenopause is critical to understanding sex differences in both normal and aberrant mental function and behavior. The studies of ADHD in females suggest confusing and non-consistent conclusions. None of these studies examined the possible relationship between phase of the menstrual cycle, sex hormones levels and ADHD symptoms. The menstrual cycle should therefore be taken into consideration in future studies in the neurocognitive field since it offers a unique opportunity to understand whether and how subtle fluctuations of sex hormones and specific combinations of sex hormones influence neuronal circuits implicated in the cognitive regulation of emotional processing. The investigation of biological models involving the role of estrogen, progesterone, and other sex steroids has the potential to generate

  2. multicast utilizando Simulated Annealing

    Directory of Open Access Journals (Sweden)

    Yezid Donoso

    2005-01-01

    Full Text Available En este artículo se presenta un método de optimización multiobjetivo para la solución del problema de balanceo de carga en redes de transmisión multicast, apoyándose en la aplicación de la meta-heurística de Simulated Annealing (Recocido Simulado. El método minimiza cuatro parámetros básicos para garantizar la calidad de servicio en transmisiones multicast: retardo origen destino, máxima utilización de enlaces, ancho de banda consumido y número de saltos. Los resultados devueltos por la heurística serán comparados con los resultados arrojados por el modelo matemático propuesto en investigaciones anteriores.

  3. Austenite formation during intercritical annealing

    OpenAIRE

    A. Lis; J. Lis

    2008-01-01

    Purpose: of this paper is the effect of the soft annealing of initial microstructure of the 6Mn16 steel on the kinetics of the austenite formation during next intercritical annealing.Design/methodology/approach: Analytical TEM point analysis with EDAX system attached to Philips CM20 was used to evaluate the concentration of Mn, Ni and Cr in the microstructure constituents of the multiphase steel and mainly Bainite- Martensite islands.Findings: The increase in soft annealing time from 1-60 hou...

  4. Variation in stable isotope ratios of monthly rainfall in the Douala and Yaounde cities, Cameroon: local meteoric lines and relationship to regional precipitation cycle

    Science.gov (United States)

    Wirmvem, Mengnjo Jude; Ohba, Takeshi; Kamtchueng, Brice Tchakam; Taylor, Eldred Tunde; Fantong, Wilson Yetoh; Ako, Ako Andrew

    2017-09-01

    Hydrogen (D) and oxygen (18O) stable isotopes in precipitation are useful tools in groundwater recharge and climatological investigations. This study investigated the isotopes in rainfall during the 2013 and 2014 hydrological years in the Douala and Yaounde urban cities. The objectives were to generate local meteoric water lines (LMWLs), define the spatial-temporal variations of the isotopes in rainwater and their relationship to the regional precipitation cycle, and determine the factors controlling the isotopic variation. The LWMLs in Douala and Yaounde were δD = 7.92δ18O + 12.99 and δD = 8.35δ18O + 15.29, respectively. The slopes indicate isotopic equilibrium conditions during rain formation and negligible evaporation effect during rainfall. Precipitation showed similar wide ranges in δ18O values from -5.26 to -0.75 ‰ in Douala and -5.8 to +1.81 ‰ in Yaounde suggesting a common moisture source from the Atlantic Ocean. Enriched weighted mean δ18O (wδ18O) values during the low pre- and post-monsoon showers coincided with low convective activity across the entire region. Enriched isotopic signatures also marked the West African monsoon transition phase during each hydrological year. Abrupt wδ18O depletion after the transition coincided with the monsoon onset in the region. Peak periods of monsoonal rainfall, associated with high convective activities, were characterised by the most depleted wδ18O values. Controls on isotopic variations are the amount effect and moisture recycling. The stable isotope data provide a tool for groundwater recharge studies while the isotopic correlation with regional rainfall cycle demonstrate their use as markers of moisture circulation and detecting climatic changes in precipitation.

  5. Variation in stable isotope ratios of monthly rainfall in the Douala and Yaounde cities, Cameroon: local meteoric lines and relationship to regional precipitation cycle

    Science.gov (United States)

    Wirmvem, Mengnjo Jude; Ohba, Takeshi; Kamtchueng, Brice Tchakam; Taylor, Eldred Tunde; Fantong, Wilson Yetoh; Ako, Ako Andrew

    2016-04-01

    Hydrogen (D) and oxygen (18O) stable isotopes in precipitation are useful tools in groundwater recharge and climatological investigations. This study investigated the isotopes in rainfall during the 2013 and 2014 hydrological years in the Douala and Yaounde urban cities. The objectives were to generate local meteoric water lines (LMWLs), define the spatial-temporal variations of the isotopes in rainwater and their relationship to the regional precipitation cycle, and determine the factors controlling the isotopic variation. The LWMLs in Douala and Yaounde were δD = 7.92δ18O + 12.99 and δD = 8.35δ18O + 15.29, respectively. The slopes indicate isotopic equilibrium conditions during rain formation and negligible evaporation effect during rainfall. Precipitation showed similar wide ranges in δ18O values from -5.26 to -0.75 ‰ in Douala and -5.8 to +1.81 ‰ in Yaounde suggesting a common moisture source from the Atlantic Ocean. Enriched weighted mean δ18O (wδ18O) values during the low pre- and post-monsoon showers coincided with low convective activity across the entire region. Enriched isotopic signatures also marked the West African monsoon transition phase during each hydrological year. Abrupt wδ18O depletion after the transition coincided with the monsoon onset in the region. Peak periods of monsoonal rainfall, associated with high convective activities, were characterised by the most depleted wδ18O values. Controls on isotopic variations are the amount effect and moisture recycling. The stable isotope data provide a tool for groundwater recharge studies while the isotopic correlation with regional rainfall cycle demonstrate their use as markers of moisture circulation and detecting climatic changes in precipitation.

  6. Radiation annealing in cuprous oxide

    DEFF Research Database (Denmark)

    Vajda, P.

    1966-01-01

    Experimental results from high-intensity gamma-irradiation of cuprous oxide are used to investigate the annealing of defects with increasing radiation dose. The results are analysed on the basis of the Balarin and Hauser (1965) statistical model of radiation annealing, giving a square-root relati......-root relationship between the rate of change of resistivity and the resistivity change. The saturation defect density at room temperature is estimated on the basis of a model for defect creation in cuprous oxide....

  7. Quantum annealing with manufactured spins.

    Science.gov (United States)

    Johnson, M W; Amin, M H S; Gildert, S; Lanting, T; Hamze, F; Dickson, N; Harris, R; Berkley, A J; Johansson, J; Bunyk, P; Chapple, E M; Enderud, C; Hilton, J P; Karimi, K; Ladizinsky, E; Ladizinsky, N; Oh, T; Perminov, I; Rich, C; Thom, M C; Tolkacheva, E; Truncik, C J S; Uchaikin, S; Wang, J; Wilson, B; Rose, G

    2011-05-12

    Many interesting but practically intractable problems can be reduced to that of finding the ground state of a system of interacting spins; however, finding such a ground state remains computationally difficult. It is believed that the ground state of some naturally occurring spin systems can be effectively attained through a process called quantum annealing. If it could be harnessed, quantum annealing might improve on known methods for solving certain types of problem. However, physical investigation of quantum annealing has been largely confined to microscopic spins in condensed-matter systems. Here we use quantum annealing to find the ground state of an artificial Ising spin system comprising an array of eight superconducting flux quantum bits with programmable spin-spin couplings. We observe a clear signature of quantum annealing, distinguishable from classical thermal annealing through the temperature dependence of the time at which the system dynamics freezes. Our implementation can be configured in situ to realize a wide variety of different spin networks, each of which can be monitored as it moves towards a low-energy configuration. This programmable artificial spin network bridges the gap between the theoretical study of ideal isolated spin networks and the experimental investigation of bulk magnetic samples. Moreover, with an increased number of spins, such a system may provide a practical physical means to implement a quantum algorithm, possibly allowing more-effective approaches to solving certain classes of hard combinatorial optimization problems.

  8. Monthly errors

    Data.gov (United States)

    U.S. Environmental Protection Agency — The 2006 monthly average statistical metrics for 2m Q (g kg-1) domain-wide for the base and MODIS WRF simulations against MADIS observations. This dataset is...

  9. Thermal Annealing of Exfoliated Graphene

    Directory of Open Access Journals (Sweden)

    Wang Xueshen

    2013-01-01

    Full Text Available Monolayer graphene is obtained by mechanical exfoliation using scotch tapes. The effects of thermal annealing on the tape residues and edges of graphene are researched. Atomic force microscope images showed that almost all the residues could be removed in N2/H2 at 400°C but only agglomerated in vacuum. Raman spectra of the annealed graphene show both the 2D peak and G peak blueshift. The full width at half maximum (FWHM of the 2D peak becomes larger and the intensity ratio of the 2D peak to G peak decreases. The edges of graphene are completely attached to the surface of the substrate after annealing.

  10. MEDICAL STAFF SCHEDULING USING SIMULATED ANNEALING

    Directory of Open Access Journals (Sweden)

    Ladislav Rosocha

    2015-07-01

    Full Text Available Purpose: The efficiency of medical staff is a fundamental feature of healthcare facilities quality. Therefore the better implementation of their preferences into the scheduling problem might not only rise the work-life balance of doctors and nurses, but also may result into better patient care. This paper focuses on optimization of medical staff preferences considering the scheduling problem.Methodology/Approach: We propose a medical staff scheduling algorithm based on simulated annealing, a well-known method from statistical thermodynamics. We define hard constraints, which are linked to legal and working regulations, and minimize the violations of soft constraints, which are related to the quality of work, psychic, and work-life balance of staff.Findings: On a sample of 60 physicians and nurses from gynecology department we generated monthly schedules and optimized their preferences in terms of soft constraints. Our results indicate that the final value of objective function optimized by proposed algorithm is more than 18-times better in violations of soft constraints than initially generated random schedule that satisfied hard constraints.Research Limitation/implication: Even though the global optimality of final outcome is not guaranteed, desirable solutionwas obtained in reasonable time. Originality/Value of paper: We show that designed algorithm is able to successfully generate schedules regarding hard and soft constraints. Moreover, presented method is significantly faster than standard schedule generation and is able to effectively reschedule due to the local neighborhood search characteristics of simulated annealing.

  11. Dependency of annealing behaviour on grain size in Al–TiC composite produced by accumulative roll bonding

    Indian Academy of Sciences (India)

    HAMID REZA JAFARIAN; JAFAR HABIBI-LIVAR

    2017-06-01

    This work investigates the effect of grain size on annealing behaviour in both coarse-grained and ultrafinegrained Al–TiC composite processed by accumulative roll bonding (ARB). Microstructural analysis indicates that annealingbehaviour of the specimens are essentially determined by the level of strain accumulation or number of ARB cycles, i.e., recrystallization phenomenon are accelerated by increasing the level of strain accumulation or number of ARB cycles. Microstructure analysis illustrates that annealing treatment at 200 or 250$^{\\circ}$C for the 1-cycle ARB-processed Al–TiC compositehaving coarse grains does not lead to the recrystallization phenomenon, indicating that only recovery appears. In contrast, partial recrystallization occurred after annealing at 250$^{\\circ}$C in the 7-cycle ARB-processed Al–TiC composite having ultrafine grains. Furthermore, annealing treatment significantly enhanced elongation for both ultrafine as well as coarse-grained Al–TiC composites in spite of the fact that yield and ultimate strength decreased during annealing treatment. The results proved that yield strength and tensile strengths for both 1-cycle and 7-cycle ARB-processed Al–TiC composites gradually decreased by annealing treatments between 200 and 300$^{\\circ}$C. In contrast, ultimate elongation drastically improved by about 100% after annealing at the aforementioned conditions.

  12. Annealing properties of rice starch.

    Science.gov (United States)

    Thermal properties of starch can be modified by annealing, i.e., a pre-treatment in excessive amounts of water at temperatures below the gelatinization temperatures. This treatment is known to improve the crystalline properties, and is a useful tool to gain a better control of the functional proper...

  13. Microstructural Coarsening during Thermomechanical Fatigue and Annealing of Micro Flip-Chip Solder Joints

    Energy Technology Data Exchange (ETDEWEB)

    Barney, Monica Michele [Univ. of California, Berkeley, CA (United States)

    1998-12-01

    Microstructural evolution due to thermal effects was studied in micro solder joints (55 ± 5 μm). The composition of the Sn/Pb solder studied was found to be hypereutectic with a tin content of 65-70 wt%.This was determined by Energy Dispersive X-ray analysis and confirmed with quantitative stereology. The quantitative stereological value of the surface-to-volume ratio was used to characterize and compare the coarsening during thermal cycling from 0-160 C to the coarsening during annealing at 160 C. The initial coarsening of the annealed samples was more rapid than the cycled samples, but tapered off as time to the one-half as expected. Because the substrates to which the solder was bonded have different thermal expansion coefficients, the cycled samples experienced a mechanical strain with thermal cycling. The low-strain cycled samples had a 2.8% strain imposed on the solder and failed by 1,000 cycles, despite undergoing less coarsening than the annealed samples. The high-strain cycled samples experienced a 28% strain and failed between 25 and 250 cycles. No failures were observed in the annealed samples. Failure mechanisms and processing issues unique to small, fine pitch joints are also discussed.

  14. Dislocation Reduction of HgCdTe/Si Through Ex Situ Annealing

    Science.gov (United States)

    2016-06-07

    position, policy or decision, unless so designated by other documentation. 12. DISTRIBUTION AVAILIBILITY STATEMENT Approved for public release; distribution...967 mercury overpressure needed to maintain the surface morphologies and composition of HgCdTe, a cap layer of ZnTe or ZnSe was used for these...proper surface morphology could be main- tained. The cycle annealing process was also com- pared with our standard device annealing process in terms of

  15. Feasibility of Simulated Annealing Tomography

    CERN Document Server

    Vo, Nghia T; Moser, Herbert O

    2014-01-01

    Simulated annealing tomography (SAT) is a simple iterative image reconstruction technique which can yield a superior reconstruction compared with filtered back-projection (FBP). However, the very high computational cost of iteratively calculating discrete Radon transform (DRT) has limited the feasibility of this technique. In this paper, we propose an approach based on the pre-calculated intersection lengths array (PILA) which helps to remove the step of computing DRT in the simulated annealing procedure and speed up SAT by over 300 times. The enhancement of convergence speed of the reconstruction process using the best of multiple-estimate (BoME) strategy is introduced. The performance of SAT under different conditions and in comparison with other methods is demonstrated by numerical experiments.

  16. Influence of annealing temperature on the morphology and the supercapacitance behavior of iron oxide nanotube (Fe-NT)

    Science.gov (United States)

    Sarma, Biplab; Jurovitzki, Abraham L.; Smith, York R.; Ray, Rupashree S.; Misra, Mano

    2014-12-01

    The article demonstrates the influence of annealing temperature on the supercapacitance behavior of iron oxide nanotube synthesized on pure iron substrate by electrochemical anodization process. Anodization was performed in an ethylene glycol solution containing 3% H2O and 0.5 wt. % NH4F. The as-anodized nanotubes were annealed in an ambient atmosphere at various temperatures ranging from 200 to 700 °C for a fixed duration of time (2 h). The morphology and crystal phases developed after anodization and subsequent annealing processes were examined using field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD) and X-ray photospectroscopy (XPS). Cyclic voltammetry (CV), galvanostatic charge/discharge and electrochemical impedance spectroscopy (EIS) experiments were performed in 1 M Li2SO4 to evaluate the electrochemical capacitance properties of the oxide nanotube electrodes. It was found that the electrode annealed at 300 °C exhibited superior electrochemical capacitance compared to the electrodes annealed at other temperatures. The highest specific capacitance achieved after annealing at 300 °C was about 314 mF cm-2. The electrodes annealed at 200, 500, 600 and 700 °C displayed much lower specific capacitance compared to those annealed at 300 and 400 °C. Galvanostatic charge-discharge experiments conducted on some of the annealed electrodes demonstrated excellent cycle stability with more than 80% capacitance retention after 1000 charge-discharge cycles.

  17. Recursive simulation of quantum annealing

    CERN Document Server

    Sowa, A P; Samson, J H; Savel'ev, S E; Zagoskin, A M; Heidel, S; Zúñiga-Anaya, J C

    2015-01-01

    The evaluation of the performance of adiabatic annealers is hindered by lack of efficient algorithms for simulating their behaviour. We exploit the analyticity of the standard model for the adiabatic quantum process to develop an efficient recursive method for its numerical simulation in case of both unitary and non-unitary evolution. Numerical simulations show distinctly different distributions for the most important figure of merit of adiabatic quantum computing --- the success probability --- in these two cases.

  18. Residual entropy and simulated annealing

    OpenAIRE

    Ettelaie, R.; Moore, M. A.

    1985-01-01

    Determining the residual entropy in the simulated annealing approach to optimization is shown to provide useful information on the true ground state energy. The one-dimensional Ising spin glass is studied to exemplify the procedure and in this case the residual entropy is related to the number of one-spin flip stable metastable states. The residual entropy decreases to zero only logarithmically slowly with the inverse cooling rate.

  19. Simulated annealing model of acupuncture

    Science.gov (United States)

    Shang, Charles; Szu, Harold

    2015-05-01

    The growth control singularity model suggests that acupuncture points (acupoints) originate from organizers in embryogenesis. Organizers are singular points in growth control. Acupuncture can cause perturbation of a system with effects similar to simulated annealing. In clinical trial, the goal of a treatment is to relieve certain disorder which corresponds to reaching certain local optimum in simulated annealing. The self-organizing effect of the system is limited and related to the person's general health and age. Perturbation at acupoints can lead a stronger local excitation (analogous to higher annealing temperature) compared to perturbation at non-singular points (placebo control points). Such difference diminishes as the number of perturbed points increases due to the wider distribution of the limited self-organizing activity. This model explains the following facts from systematic reviews of acupuncture trials: 1. Properly chosen single acupoint treatment for certain disorder can lead to highly repeatable efficacy above placebo 2. When multiple acupoints are used, the result can be highly repeatable if the patients are relatively healthy and young but are usually mixed if the patients are old, frail and have multiple disorders at the same time as the number of local optima or comorbidities increases. 3. As number of acupoints used increases, the efficacy difference between sham and real acupuncture often diminishes. It predicted that the efficacy of acupuncture is negatively correlated to the disease chronicity, severity and patient's age. This is the first biological - physical model of acupuncture which can predict and guide clinical acupuncture research.

  20. Blue thermoluminescence emission of annealed lithium rich aluminosilicates

    Energy Technology Data Exchange (ETDEWEB)

    Correcher, V.; Rodriguez-Lazcano, Y., E-mail: v.correcher@ciemat.e [CIEMAT, Madrid (Spain); Garcia-Guinea, J.; Crespo-Feo, E. [Museo Nacional de Ciencias Naturales, Madrid (Spain)

    2010-09-15

    The blue thermoluminescence (TL) emission of different thermally annealed {beta}-eucryptite (LiAlSiO{sub 4}), virgilite-petalite (LiAlSi{sub 5}O{sub 12}) and virgilite-petalite-bikitaite (LiAlSi{sub 10}O{sub 22}) mixed crystals have been studied. The observed changes in the TL glow curves could be linked to simultaneous processes taking place in the lithium aluminosilicate lattice structure (phase transitions, consecutive breaking linking of bonds, alkali self-diffusion, redox reactions, etc). The stability of the TL signal after four months of storage performed at RT under red light, shows big differences between annealed (12 hours at 1200 deg C) and non-annealed samples. The fading process in non-annealed samples can be fitted to a first-order decay mathematical expression; however preheated samples could not be reasonably fitted due to the highly dispersion detected. The changes observed in the X-ray diffractograms are in the intensity of the peaks that denote modifications in the degree of crystallinity and, in addition, there are some differences in the appearance of new peaks that could suppose new phases (e.g. b-spodumene). (author)

  1. A 6-Month, Double-Blind, Maintenance Trial of Lithium Monotherapy Versus the Combination of Lithium and Divalproex for Rapid-Cycling Bipolar Disorder and Co-Occurring Substance Abuse or Dependence

    Science.gov (United States)

    Kemp, David E.; Gao, Keming; Ganocy, Stephen J.; Rapport, Daniel J.; Elhaj, Omar; Bilali, Sarah; Conroy, Carla; Findling, Robert L.; Calabrese, Joseph R.

    2011-01-01

    Objective To assess whether combination treatment with lithium and divalproex is more effective than lithium monotherapy in prolonging the time to mood episode recurrence in patients with rapid-cycling bipolar disorder (RCBD) and comorbid substance abuse and/or dependence. Method A 6-month, double-blind, parallel group comparison was carried out in recently manic/hypomanic/mixed patients who had demonstrated a persistent bimodal response to combined treatment with lithium and divalproex. Subjects were randomly assigned to remain on combination treatment or to discontinue divalproex and remain on lithium monotherapy. Results Of 149 patients enrolled into the open-label acute stabilization phase, 79% discontinued prematurely (poor adherence: 42%; nonresponse: 25%; intolerable side effects: 10%). Of 31 patients (21%) randomly assigned to double-blind maintenance treatment, 55% relapsed (24% into depression and 76% into a manic/hypomanic/mixed episode), 26% completed the study, and 19% were poorly adherent or exited prematurely. The median time to recurrence of a new mood episode was 15.9 weeks for patients receiving lithium monotherapy and 17.8 weeks for patients receiving the combination of lithium and divalproex (p=NS). The rate of relapse into a mood episode for those receiving lithium monotherapy or the combination of lithium and divalproex was 56% and 53%, respectively. The rate of depressive relapse in both arms was 13%, while the rate of relapse into a manic, hypomanic, or mixed episode was 44% for lithium monotherapy and 40% for the combination of lithium and divalproex. Conclusion A small subgroup of patients in this study stabilized after six months of treatment with lithium plus divalproex. Of those who did, the addition of divalproex to lithium conferred no additional prophylactic benefit over lithium alone. Although depression is regarded as the hallmark of RCBD in general, these data suggest that recurrent episodes of mania tend to be more common in

  2. Strong white photoluminescence from annealed zeolites

    Energy Technology Data Exchange (ETDEWEB)

    Bai, Zhenhua, E-mail: baizh46@gmail.com [School of Chemical and Biomedical Engineering, Nanyang Technological University, Singapore 637457 (Singapore); Fujii, Minoru; Imakita, Kenji; Hayashi, Shinji [Department of Electrical and Electronic Engineering, Graduate School of Engineering, Kobe University, Rokkodai, Nada, Kobe 657-8501 (Japan)

    2014-01-15

    The optical properties of zeolites annealed at various temperatures are investigated for the first time. The annealed zeolites exhibit strong white photoluminescence (PL) under ultraviolet light excitation. With increasing annealing temperature, the emission intensity of annealed zeolites first increases and then decreases. At the same time, the PL peak red-shifts from 495 nm to 530 nm, and then returns to 500 nm. The strongest emission appears when the annealing temperature is 500 °C. The quantum yield of the sample is measured to be ∼10%. The PL lifetime monotonously increases from 223 μs to 251 μs with increasing annealing temperature. The origin of white PL is ascribed to oxygen vacancies formed during the annealing process. -- Highlights: • The optical properties of zeolites annealed at various temperatures are investigated. • The annealed zeolites exhibit strong white photoluminescence. • The maximum PL enhancement reaches as large as 62 times. • The lifetime shows little dependence on annealing temperature. • The origin of white emission is ascribed to the oxygen vacancies.

  3. Loviisa Unit One: Annealing - healing

    Energy Technology Data Exchange (ETDEWEB)

    Kohopaeae, J.; Virsu, R. [ed.; Henriksson, A. [ed.

    1997-11-01

    Unit 1 of the Loviisa nuclear powerplant was annealed in connection with the refuelling outage in the summer of 1996. This type of heat treatment restored the toughness properties of the pressure vessel weld, which had been embrittled be neutron radiation, so that it is almost equivalent to a new weld. The treatment itself was an ordinary metallurgical procedure that took only a few days. But the material studies that preceded it began over fifteen years ago and have put IVO at the forefront of world-wide expertise in the area of radiation embrittlement

  4. Keystream Generator Based On Simulated Annealing

    Directory of Open Access Journals (Sweden)

    Ayad A. Abdulsalam

    2011-01-01

    Full Text Available Advances in the design of keystream generator using heuristic techniques are reported. A simulated annealing algorithm for generating random keystream with large complexity is presented. Simulated annealing technique is adapted to locate these requirements. The definitions for some cryptographic properties are generalized, providing a measure suitable for use as an objective function in a simulated annealing algorithm, seeking randomness that satisfy both correlation immunity and the large linear complexity. Results are presented demonstrating the effectiveness of the method.

  5. DOE`s annealing prototype demonstration projects

    Energy Technology Data Exchange (ETDEWEB)

    Warren, J.; Nakos, J.; Rochau, G.

    1997-02-01

    One of the challenges U.S. utilities face in addressing technical issues associated with the aging of nuclear power plants is the long-term effect of plant operation on reactor pressure vessels (RPVs). As a nuclear plant operates, its RPV is exposed to neutrons. For certain plants, this neutron exposure can cause embrittlement of some of the RPV welds which can shorten the useful life of the RPV. This RPV embrittlement issue has the potential to affect the continued operation of a number of operating U.S. pressurized water reactor (PWR) plants. However, RPV material properties affected by long-term irradiation are recoverable through a thermal annealing treatment of the RPV. Although a dozen Russian-designed RPVs and several U.S. military vessels have been successfully annealed, U.S. utilities have stated that a successful annealing demonstration of a U.S. RPV is a prerequisite for annealing a licensed U.S. nuclear power plant. In May 1995, the Department of Energy`s Sandia National Laboratories awarded two cost-shared contracts to evaluate the feasibility of annealing U.S. licensed plants by conducting an anneal of an installed RPV using two different heating technologies. The contracts were awarded to the American Society of Mechanical Engineers (ASME) Center for Research and Technology Development (CRTD) and MPR Associates (MPR). The ASME team completed its annealing prototype demonstration in July 1996, using an indirect gas furnace at the uncompleted Public Service of Indiana`s Marble Hill nuclear power plant. The MPR team`s annealing prototype demonstration was scheduled to be completed in early 1997, using a direct heat electrical furnace at the uncompleted Consumers Power Company`s nuclear power plant at Midland, Michigan. This paper describes the Department`s annealing prototype demonstration goals and objectives; the tasks, deliverables, and results to date for each annealing prototype demonstration; and the remaining annealing technology challenges.

  6. Modernizing quantum annealing using local searches

    Science.gov (United States)

    Chancellor, Nicholas

    2017-02-01

    I describe how real quantum annealers may be used to perform local (in state space) searches around specified states, rather than the global searches traditionally implemented in the quantum annealing algorithm (QAA). Such protocols will have numerous advantages over simple quantum annealing. By using such searches the effect of problem mis-specification can be reduced, as only energy differences between the searched states will be relevant. The QAA is an analogue of simulated annealing, a classical numerical technique which has now been superseded. Hence, I explore two strategies to use an annealer in a way which takes advantage of modern classical optimization algorithms. Specifically, I show how sequential calls to quantum annealers can be used to construct analogues of population annealing and parallel tempering which use quantum searches as subroutines. The techniques given here can be applied not only to optimization, but also to sampling. I examine the feasibility of these protocols on real devices and note that implementing such protocols should require minimal if any change to the current design of the flux qubit-based annealers by D-Wave Systems Inc. I further provide proof-of-principle numerical experiments based on quantum Monte Carlo that demonstrate simple examples of the discussed techniques.

  7. Growth of intermetallic phases in Al/Cu composites at various annealing temperatures during the ARB process

    Science.gov (United States)

    Hsieh, Chih-Chun; Shi, Ming-Shou; Wu, Weite

    2012-02-01

    The purpose of this study is to discuss the effect of annealing temperatures on growth of intermetallic phases in Al/Cu composites during the accumulative roll bonding (ARB) process. Pure Al (AA1100) and pure Cu (C11000) were stacked into layered structures at 8 cycles as annealed at 300 °C and 400 °C using the ARB technique. Microstructural results indicate that the necking of layered structures occur after 300 °C annealing. Intermetallic phases grow and form a smashed morphology of Al and Cu when annealed at 400 °C. From the XRD and EDS analysis results, the intermetallic phases of Al2Cu (θ) and Al4Cu9 (γ2) formed over 6 cycles and the AlCu (η2) precipitated at 8 cycles after 300 °C annealing. Three phases (Al2Cu (θ), Al4Cu9 (γ2), and AlCu (η2)) were formed over 2 cycles after 400 °C annealing.

  8. Understanding the microwave annealing of silicon

    Directory of Open Access Journals (Sweden)

    Chaochao Fu

    2017-03-01

    Full Text Available Though microwave annealing appears to be very appealing due to its unique features, lacking an in-depth understanding and accurate model hinder its application in semiconductor processing. In this paper, the physics-based model and accurate calculation for the microwave annealing of silicon are presented. Both thermal effects, including ohmic conduction loss and dielectric polarization loss, and non-thermal effects are thoroughly analyzed. We designed unique experiments to verify the mechanism and extract relevant parameters. We also explicitly illustrate the dynamic interaction processes of the microwave annealing of silicon. This work provides an in-depth understanding that can expedite the application of microwave annealing in semiconductor processing and open the door to implementing microwave annealing for future research and applications.

  9. Electrochemical capacitance of iron oxide nanotube (Fe-NT): effect of annealing atmospheres

    Science.gov (United States)

    Sarma, Biplab; Jurovitzki, Abraham L.; Ray, Rupashree S.; Smith, York R.; Mohanty, Swomitra K.; Misra, Mano

    2015-07-01

    The effect of annealing atmosphere on the supercapacitance behavior of iron oxide nanotube (Fe-NT) electrodes has been explored and reported here. Iron oxide nanotubes were synthesized on a pure iron substrate through an electrochemical anodization process in an ethylene glycol solution containing 3% H2O and 0.5 wt.% NH4F. Subsequently, the annealing of the nanotubes was carried out at 500 °C for 2 h in various gas atmospheres such as air, oxygen (O2), nitrogen (N2), and argon (Ar). The morphology and crystal phases evolved after the annealing processes were examined via field emission scanning electron microscopy, x-ray diffraction, Raman spectroscopy, and x-ray photoelectron spectroscopy. The electrochemical capacitance properties of the annealed Fe-NT electrodes were evaluated by conducting cyclic voltammetry (CV), galvanostatic charge-discharge, and electrochemical impedance spectroscopy tests in the Li2SO4 electrolyte. Based on these experiments, it was found that the capacitance of the Fe-NT electrodes annealed in air and O2 atmospheres shows mixed behavior comprising both the electric double layer and pseudocapacitance. However, annealing in N2 and Ar environments resulted in well-defined redox peaks in the CV profiles of the Fe-NT electrodes, which are therefore attributed to the relatively higher pseudonature of the capacitance in these electrodes. Based on the galvanostatic charge-discharge studies, the specific capacitance achieved in the Fe-NT electrode after annealing in Ar was about 300 mF cm-2, which was about twice the value obtained for N2-annealed Fe-NTs and three times higher than those annealed in air and O2. The experiments also demonstrated excellent cycle stability for the Fe-NT electrodes with 83%-85% capacitance retention, even after many charge-discharge cycles, irrespective of the gas atmospheres used during annealing. The increase in the specific capacitance was discussed in terms of increased oxygen vacancies as a result of the

  10. Algoritmo recocido simulado para el problema de la programación del tamaño del lote económico bajo el enfoque de ciclo básico Simulated annealing algorithm to solve the economic lot scheduling problem and the basic cycle approach

    Directory of Open Access Journals (Sweden)

    José Omar Hernández

    2011-12-01

    Full Text Available La programación del tamaño del lote económico consiste en determinar la secuencia y la cantidad a fabricar de N productos en un equipo o máquina, la cual tiene una capacidad limitada. Se trata de un problema NP-duro y las propuestas de solución son diversas. En esta investigación se trabaja con el enfoque del ciclo básico planteado por Bomberger, para el cual existen varias propuestas, dentro de las cuales se pueden encontrar hasta el momento sólo algoritmos genéticos en lo que se refiere a la implementación de técnicas metaheurísticas para resolver el problema. En este trabajo se resuelve el problema de muestra de Bomberger mediante la metaheurística recocido simulado; las aportaciones de esta investigación consisten en la forma de obtener un espacio de búsqueda más restringido de las variables, y una estrategia para controlar la exploración del espacio de soluciones que realiza el algoritmo, de tal manera que se realice una búsqueda eficiente. Dado que es una primera implementación de recocido simulado se experimenta con varias combinaciones de parámetros. El algoritmo obtiene los mismos costos en casi todas las pruebas realizadas; sin embargo, en las pruebas donde la relación es alta, el algoritmo se desempeña mejor, mejorando la solución reportada anteriormente en algunos de los experimentos.The problem considered is that of scheduling the production of several different items over the same machine with restricted capacity and on a repetitive basis. The problem is NP-hard and there exist several methods for the problem. In this research we worked with Bomberger's basic cycle approach, for which there are reported several solution proposals, among which are found so far only genetic algorithms in regard to the implementation of metaheuristic techniques to solve the problem. We solved Bomberger's classical example problem, applying simulated annealing metaheuristic. The contributions of this research consist on how to

  11. Laser surface annealing technique of aged Inconel 718 by laser beam irradiation

    Science.gov (United States)

    Liu, Liufa; Hirose, Akio; Kobayashi, Kojiro F.

    2003-03-01

    Laser was employed to anneal a thin surface layer of aged Inconel 718 by dissolving the strengthening phase, γ". The HE (Hydrogen Embrittlement) resistance of the alloy was improved via such laser surface annealing (LSA) processes. To establish a general LSA technique for engineer applications, experimental LSA processes were conducted to study the effects of the laser process parameters on the formation of the annealed surface layers, and applicable process parameter ranges were obtained. Next, a numerical method was developed for predicting the formation of the laser annealed surface layers in the following steps. Because only the γ" phase was dissolved in the LSA process, the dissolution kinetics of this phase was studied via thermal cycling experiments, and it was proved to follow an Avrami equation. FEM (Finite Element Method) simulations were conducted to calculate the thermal distribution in each laser annealed surface layer, and thermal history data were extracted every certain depth. The volume fractions of the γ" phase at these depths were calculated using these thermal history data based on the deduced Avrami equation. Using a developed relationship between the hardness variation of the alloy and the volume fraction variation of the γ" phase, the hardness distribution in the annealed surface layer and this layer's thickness were calculated. The predicted applicable laser process parameter ranges were obtained. These calculated results were compared with their corresponding experimental results. The good agreements between the calculated and measured results suggested that this numerical prediction approach is feasible for engineer applications.

  12. Accumulative Roll Bonding and Post-Deformation Annealing of Cu-Al-Mn Shape Memory Alloy

    Science.gov (United States)

    Moghaddam, Ahmad Ostovari; Ketabchi, Mostafa; Afrasiabi, Yaser

    2014-12-01

    Accumulative roll bonding is a severe plastic deformation process used for Cu-Al-Mn shape memory alloy. The main purpose of this study is to investigate the possibility of grain refinement of Cu-9.5Al-8.2Mn (in wt.%) shape memory alloy using accumulative roll bonding and post-deformation annealing. The alloy was successfully subjected to 5 passes of accumulative roll bonding at 600 °C. The microstructure, properties as well as post-deformation annealing of this alloy were investigated by optical microscopy, scanning electron microscopy, x-ray diffraction, differential scanning calorimeter, and bend and tensile testing. The results showed that after 5 passes of ARB at 600 °C, specimens possessed α + β microstructure with the refined grains, but martensite phases and consequently shape memory effect completely disappeared. Post-deformation annealing was carried out at 700 °C, and the martensite phase with the smallest grain size (less than 40 μm) was obtained after 150 s of annealing at 700 °C. It was found that after 5 passes of ARB and post-deformation annealing, the stability of SME during thermal cycling improved. Also, tensile properties of alloys significantly improved after post-deformation annealing.

  13. Improvement to the pattern of control rods of the equilibrium cycle of 18 months for the CLV using bio-inspired algorithms; Mejora del patron de barras de control del ciclo de equilibrio de 18 meses para la CLV empleando algoritmos bio-inspirados

    Energy Technology Data Exchange (ETDEWEB)

    Perusquia, R.; Ortiz, J.J.; Montes, J.L. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: rpc@nuclear.inin.mx

    2003-07-01

    Nowadays in the National Institute of Nuclear Research are carried out studies with some bio-inspired optimization techniques to improve the performance of the fuel cycles of the boiling water reactors of the Laguna Verde power plant (CLV). In the present work two bio-inspired techniques were applied with the purpose of improving the performance of a balance cycle of 18 months developed for the CLV: genetic algorithms (AG) and systems based on ants colonies (SCH). The design of the reference cycle it represents in several aspects an optimal cycle proposed starting from the experience of several operation decades with the boiling water reactors (BWR initials for Boiling Water Reactor) in the world. To try to improve their performance is beforehand a difficult challenge and it puts on test the feasibility of the optimization methods in the reloads design. The study of the bio-inspired techniques was centered exclusively on the obtaining of the control rod patterns (PBC) trying to overcome the capacity factor reached in the design of the reference cycle. It was fixed the cycle length such that the decrease of the coast down period would represent an increase of the capacity factor of the cycle; so that, it diminishes the annual cost associated with the capital cost of the plant. As consequence of the study, was found that the algorithm based on the ants colonies reaches to diminish the coast down period in five and half days respect to the original balance cycle, what represents an annual saving of $US 74,000. Since the original cycle was optimized, the above-mentioned, shows the ability of the SCH for the optimization of the cycle design. With the AG it was reach to approach to the original balance cycle with a coast down period greater in seven days estimating an annual penalization of $US 130,000. (Author)

  14. Cylinder packing by simulated annealing

    Directory of Open Access Journals (Sweden)

    M. Helena Correia

    2000-12-01

    Full Text Available This paper is motivated by the problem of loading identical items of circular base (tubes, rolls, ... into a rectangular base (the pallet. For practical reasons, all the loaded items are considered to have the same height. The resolution of this problem consists in determining the positioning pattern of the circular bases of the items on the rectangular pallet, while maximizing the number of items. This pattern will be repeated for each layer stacked on the pallet. Two algorithms based on the meta-heuristic Simulated Annealing have been developed and implemented. The tuning of these algorithms parameters implied running intensive tests in order to improve its efficiency. The algorithms developed were easily extended to the case of non-identical circles.Este artigo aborda o problema de posicionamento de objetos de base circular (tubos, rolos, ... sobre uma base retangular de maiores dimensões. Por razões práticas, considera-se que todos os objetos a carregar apresentam a mesma altura. A resolução do problema consiste na determinação do padrão de posicionamento das bases circulares dos referidos objetos sobre a base de forma retangular, tendo como objetivo a maximização do número de objetos estritamente posicionados no interior dessa base. Este padrão de posicionamento será repetido em cada uma das camadas a carregar sobre a base retangular. Apresentam-se dois algoritmos para a resolução do problema. Estes algoritmos baseiam-se numa meta-heurística, Simulated Annealling, cuja afinação de parâmetros requereu a execução de testes intensivos com o objetivo de atingir um elevado grau de eficiência no seu desempenho. As características dos algoritmos implementados permitiram que a sua extensão à consideração de círculos com raios diferentes fosse facilmente conseguida.

  15. Precision Laser Annealing of Focal Plane Arrays

    Energy Technology Data Exchange (ETDEWEB)

    Bender, Daniel A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); DeRose, Christopher [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Starbuck, Andrew Lea [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Verley, Jason C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jenkins, Mark W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-09-01

    We present results from laser annealing experiments in Si using a passively Q-switched Nd:YAG microlaser. Exposure with laser at fluence values above the damage threshold of commercially available photodiodes results in electrical damage (as measured by an increase in photodiode dark current). We show that increasing the laser fluence to values in excess of the damage threshold can result in annealing of a damage site and a reduction in detector dark current by as much as 100x in some cases. A still further increase in fluence results in irreparable damage. Thus we demonstrate the presence of a laser annealing window over which performance of damaged detectors can be at least partially reconstituted. Moreover dark current reduction is observed over the entire operating range of the diode indicating that device performance has been improved for all values of reverse bias voltage. Additionally, we will present results of laser annealing in Si waveguides. By exposing a small (<10 um) length of a Si waveguide to an annealing laser pulse, the longitudinal phase of light acquired in propagating through the waveguide can be modified with high precision, <15 milliradian per laser pulse. Phase tuning by 180 degrees is exhibited with multiple exposures to one arm of a Mach-Zehnder interferometer at fluence values below the morphological damage threshold of an etched Si waveguide. No reduction in optical transmission at 1550 nm was found after 220 annealing laser shots. Modeling results for laser annealing in Si are also presented.

  16. Effects of cooling rate and stabilization annealing on fatigue behavior of β-processed Ti-6Al-4V alloys

    Science.gov (United States)

    Seo, Wongyu; Jeong, Daeho; Lee, Dongjun; Sung, Hyokyung; Kwon, Yongnam; Kim, Sangshik

    2017-07-01

    The effects of stabilization annealing and cooling rate on high cycle fatigue (HCF) and fatigue crack propagation (FCP) behaviors of β-processed Ti64 alloys were examined. After β-process heating above β transus, two different cooling rates of air cooling (β-annealing) and water quenching (β-quenching) were utilized. Selected specimens were then underwent stabilization annealing. The tensile tests, HCF and FCP tests on conducted on the β-processed Ti64 specimens with and without stabilization annealing. No notable microstructural and mechanical changes with stabilization annealing was observed for the β-annealed Ti64 alloys. However, significant effect of stabilization annealing was found on the FCP behavior of β-quenched Ti64 alloys, which appeared to be related to the built-up of residual stress after quenching. The mechanical behavior of β-processed Ti64 alloys with and with stabilization annealing was discussed based on the micrographic examination, including crack growth path and crack nucleation site, and fractographic analysis.

  17. Effect of annealing temperature on structure and electrochemical properties of LiCoO2 cathode thin films

    Institute of Scientific and Technical Information of China (English)

    YANG Zhimin; XING Guangjian; YANG Jian; MAO Changhui; DU Jun

    2006-01-01

    LiCoO2 thin films, which can be used as a cathode material in microbatteries, were deposited using radio frequency (r.f.) magnetron sputtering system from a LiCoO2 target and in an O2+Ar atmosphere.The films were characterized by various methods such as XRD, SEM and AFM.The LiCoO2 films were annealed in air at 300, 500, 700 and 800 ℃ respectively.The effect of the annealing temperature on the structure, the surface morphology and the electrochemical properties of the films were investigated.The LiCoO2 thin film deposited at room temperature is amorphous and has smaller grain size.With increasing of annealing temperature, the crystallinity of the films is promoted.When the annealing temperature increases to 700 ℃, the films have a perfect crystalline LiCoO2 phase.The LiCoO2 thin film without annealing has no discharge plateau and small discharge capacity (about 27 μAh·cm-2μm).The discharge capacity increases with the increasing of annealing temperature and reaches 47 μAh·cm-2μm for the film annealed with 700 ℃, which also shows the typical discharge plateau of 3.9 V.The cycle performance of LiCoO2 thin films of as grown and annealed at different temperatures were studied.In the case of the film without thermal treatment, the capacity fading is much faster than that of the film annealed at different temperature, showing about 40% capacity loss only after 25 cycles.However, in the case of the film annealed at 700 ℃, the capacity reaches to steady state gradually and maintained constantly with cycling.After 25 times cycling, the discharge capacity of the film annealed at 700 ℃ decreases to about 36.9 μAh·cm-2·μm, only 0.8% capacity loss per cycle.

  18. Impacts of Annealing Conditions on the Flat Band Voltage of Alternate La2O3/Al2O3 Multilayer Stack Structures

    Science.gov (United States)

    Feng, Xing-Yao; Liu, Hong-Xia; Wang, Xing; Zhao, Lu; Fei, Chen-Xi; Liu, He-Lei

    2016-09-01

    The mechanism of flat band voltage (VFB) shift for alternate La2O3/Al2O3 multilayer stack structures in different annealing condition is investigated. The samples were prepared for alternate multilayer structures, which were annealed in different conditions. The capacitance-voltage (C-V) measuring results indicate that the VFB of samples shift negatively for thinner bottom Al2O3 layer, increasing annealing temperature or longer annealing duration. Simultaneously, the diffusion of high- k material to interfaces in different multilayer structures and annealing conditions is observed by X-ray photoelectron spectroscopy (XPS). Based on the dipole theory, a correlation between the diffusion effect of La towards bottom Al2O3/Si interface and VFB shift is found. Without changing the dielectric constant k of films, VFB shift can be manipulated by controlling the single-layer cycles and annealing conditions of alternate high- k multilayer stack.

  19. Global warming: Temperature estimation in annealers

    Directory of Open Access Journals (Sweden)

    Jack Raymond

    2016-11-01

    Full Text Available Sampling from a Boltzmann distribution is NP-hard and so requires heuristic approaches. Quantum annealing is one promising candidate. The failure of annealing dynamics to equilibrate on practical time scales is a well understood limitation, but does not always prevent a heuristically useful distribution from being generated. In this paper we evaluate several methods for determining a useful operational temperature range for annealers. We show that, even where distributions deviate from the Boltzmann distribution due to ergodicity breaking, these estimates can be useful. We introduce the concepts of local and global temperatures that are captured by different estimation methods. We argue that for practical application it often makes sense to analyze annealers that are subject to post-processing in order to isolate the macroscopic distribution deviations that are a practical barrier to their application.

  20. Quantum Adiabatic Evolution Algorithms versus Simulated Annealing

    CERN Document Server

    Farhi, E; Gutmann, S; Farhi, Edward; Goldstone, Jeffrey; Gutmann, Sam

    2002-01-01

    We explain why quantum adiabatic evolution and simulated annealing perform similarly in certain examples of searching for the minimum of a cost function of n bits. In these examples each bit is treated symmetrically so the cost function depends only on the Hamming weight of the n bits. We also give two examples, closely related to these, where the similarity breaks down in that the quantum adiabatic algorithm succeeds in polynomial time whereas simulated annealing requires exponential time.

  1. Influence of alloying and secondary annealing on anneal hardening effect at sintered copper alloys

    Indian Academy of Sciences (India)

    Svetlana Nestorovic

    2005-08-01

    This paper reports results of investigation carried out on sintered copper alloys (Cu, 8 at%; Zn, Ni, Al and Cu–Au with 4 at%Au). The alloys were subjected to cold rolling (30, 50 and 70%) and annealed isochronally up to recrystallization temperature. Changes in hardness and electrical conductivity were followed in order to investigate the anneal hardening effect. This effect was observed after secondary annealing also. Au and Al have been found to be more effective in inducing anneal hardening effect.

  2. Comparative study of the performance of quantum annealing and simulated annealing.

    Science.gov (United States)

    Nishimori, Hidetoshi; Tsuda, Junichi; Knysh, Sergey

    2015-01-01

    Relations of simulated annealing and quantum annealing are studied by a mapping from the transition matrix of classical Markovian dynamics of the Ising model to a quantum Hamiltonian and vice versa. It is shown that these two operators, the transition matrix and the Hamiltonian, share the eigenvalue spectrum. Thus, if simulated annealing with slow temperature change does not encounter a difficulty caused by an exponentially long relaxation time at a first-order phase transition, the same is true for the corresponding process of quantum annealing in the adiabatic limit. One of the important differences between the classical-to-quantum mapping and the converse quantum-to-classical mapping is that the Markovian dynamics of a short-range Ising model is mapped to a short-range quantum system, but the converse mapping from a short-range quantum system to a classical one results in long-range interactions. This leads to a difference in efficiencies that simulated annealing can be efficiently simulated by quantum annealing but the converse is not necessarily true. We conclude that quantum annealing is easier to implement and is more flexible than simulated annealing. We also point out that the present mapping can be extended to accommodate explicit time dependence of temperature, which is used to justify the quantum-mechanical analysis of simulated annealing by Somma, Batista, and Ortiz. Additionally, an alternative method to solve the nonequilibrium dynamics of the one-dimensional Ising model is provided through the classical-to-quantum mapping.

  3. Nanocrystalline magnetic materials obtained by flash annealing

    Directory of Open Access Journals (Sweden)

    R.K. Murakami

    1999-04-01

    Full Text Available The aim of the present work was to produce enhanced-remanence nanocrystalline magnetic material by crystallizing amorphous or partially amorphous Pr4.5Fe77B18.5 alloys by the flash annealing process, also known as the dc-Joule heating process, and to determine the optimal conditions for obtaining good magnetic coupling between the magnetic phases present in this material. Ribbons of Pr4.5Fe77B18.5 were produced by melt spinning and then annealed for 10-30 s at temperatures 500 - 640 °C by passing current through the sample to develop the enhanced-remanence nanocrystalline magnetic material. These materials were studied by X-ray diffraction, differential thermal analysis and magnetic measurements. Coercivity increases of up to 15% were systematically observed in relation to furnace-annealed material. Two different samples were carefully examined: (i a sample annealed at 600 °C which showed the highest coercive field Hc and remanence ratio Mr/Ms and (ii a sample annealed at 520 °C which showed phase separation in the second quadrant demagnetization curve. Our results are in agreement with other studies which show that flash annealing improves the magnetic properties of some amorphous ferromagnetic ribbons.

  4. An Application of Simulated Annealing to Scheduling Army Unit Training

    Science.gov (United States)

    1986-10-01

    Simulated annealing operates by analogy to the metalurgy process which strengthens metals through successive heating and cooling. The method is highly...diminishing returns is observed. The simulated annealing heuristic operates by analogy to annealing in physical systems. Annealing in a physical

  5. A twelve-month comparative clinical investigation of two low-dose oral contraceptives containing 20 micrograms ethinylestradiol/75 micrograms gestodene and 30 micrograms ethinylestradiol/75 micrograms gestodene, with respect to efficacy, cycle control, and tolerance.

    Science.gov (United States)

    Endrikat, J; Müller, U; Düsterberg, B

    1997-03-01

    The aim of this study was to compare contraceptive reliability, cycle control, and tolerance of an oral contraceptive containing 20 micrograms ethinylestradiol (EE2) and 75 micrograms gestodene (GSD), with a reference preparation containing a similar dose of gestodene but in combination with 30 micrograms ethinylestradiol. A higher incidence of intermenstrual bleeding was apparent under the 20 micrograms EE2 oral contraceptive. For the 20 micrograms EE2 preparation, 47.4% of all women reported spotting at least once over a period of 12 treatment cycles, whereas this figure was 35.5% for the 30 micrograms EE2 pill (p < 0.05). However, the incidence was within a range that corresponds to that of other OCs. The cumulative breakthrough bleeding rates (at least once during the one year of treatment) of 14.5% (20 micrograms EE2) and 11.8% (30 micrograms EE2) of women were not significantly different. In relation to all cycles, the intermenstrual bleeding rates were remarkably lower, indicating that the majority of the volunteers experienced such events only in few cycles under treatment: the spotting rate was 11.5% (20 micrograms EE2) and 7.2% (30 micrograms EE2) of all cycles, and the breakthrough bleeding rate was 2.6% and 1.6% of all cycles, respectively. Three pregnancies were recorded during the study (one in the 20 micrograms EE2 + 75 micrograms GSD group, two in the 30 micrograms EE2 + 75 micrograms GSD group). All three could be explained either by intake irregularities or by circumstances impairing the contraceptive effect. The influence of both treatments on the blood pressure and body weight proved to be extremely slight. Adverse events in both groups were rare and differences in the frequency of adverse events were not apparent. The discontinuation rate due to adverse events, including intermenstrual bleeding, was low (9.8% for 20 micrograms EE2 + 75 micrograms GSD, and 7.2% for 30 micrograms EE2 + 75 micrograms GSD) and was in the lower range known for other

  6. Origin of reverse annealing effect in hydrogen-implanted silicon

    Energy Technology Data Exchange (ETDEWEB)

    Di, Zengfeng [Los Alamos National Laboratory; Nastasi, Michael A [Los Alamos National Laboratory; Wang, Yongqiang [Los Alamos National Laboratory

    2009-01-01

    In contradiction to conventional damage annealing, thermally annealed H-implanted Si exhibits an increase in damage or reverse annealing behavior, whose mechanism has remained elusive. On the basis of quantitative high resolution transmission electron microscopy combined with channeling Rutherford backscattering analysis, we conclusively elucidate that the reverse annealing effect is due to the nucleation and growth of hydrogen-induce platelets. Platelets are responsible for an increase in the height and width the channeling damage peak following increased isochronal anneals.

  7. A twelve-month comparative clinical investigation of two low-dose oral contraceptives containing 20 micrograms ethinylestradiol/75 micrograms gestodene and 20 micrograms ethinylestradiol/150 micrograms desogestrel, with respect to efficacy, cycle control and tolerance.

    Science.gov (United States)

    Endrikat, J; Jaques, M A; Mayerhofer, M; Pelissier, C; Müller, U; Düsterberg, B

    1995-10-01

    The aim of this study was to compare contraceptive reliability, cycle control and tolerance of an oral contraceptive containing 20 micrograms ethinylestradiol and 75 micrograms gestodene, with a reference preparation containing the same dose of estrogen combined with 150 micrograms desogestrel. This article presents interim data from centers in France and Austria, involving a total of 479 women and 4,991 cycles. Contraceptive reliability was good with both preparations. Two pregnancies occurred in the gestodene group, but neither were due to method failure. In the desogestrel group there were also two pregnancies, of which one was due to method failure. With respect to cycle control, there is a trend towards a lower incidence of intermenstrual bleeding in the gestodene group. The incidence of spotting (scanty bleeding) during the important first three cycles was 3.5% lower in the gestodene group, and over the first six cycles, it was 7.6% lower. Amenorrhea was similar in both groups, but the incidence of dysmenorrhea was significantly lower in the gestodene group (p=0.001). Adverse events were similar in both groups, with headache, breast tension and nausea the most frequently reported symptoms. Body weight remained relatively constant during treatment in both groups, and no hypertension was reported for any woman during the course of the study. In each treatment group, 19 women discontinued because of adverse events. It is concluded that both preparation are reliable and well tolerated oral contraceptives are reliable and well tolerated oral contraceptives; however, there is a more favourable effect on dysmenorrhea by the gestodene formulation.

  8. Monthly Meteorological Reports

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Monthly forms that do not fit into any regular submission. Tabulation sheets and generic monthly forms designed to capture miscellaneous monthly observations.

  9. The Effect of Rapid Thermal Annealing Towards the Performance of Screen-Printed Si Solar Cell

    Directory of Open Access Journals (Sweden)

    Shahrul Anizan

    2011-01-01

    Full Text Available Problem statement: Solar cells are used to capture the photons which generate the energy. However the efficiency of the cells to turn the amount of photon to electricity needs to be high and so the cells enhancement is needed. This involved the whole process of the developing of the cells, thus annealing process is one of the important steps that needs to be optimised. Approach: Only Si solar cells will be discussed and the processes involved would be metal contact screen printing and metal paste co-firing. The contacts were first screen printed with Al paste for the rear side and Ag paste for the front side of the cell. Cells are then fired in the annealing furnace using selected temperature profile. Few sets of temperature profiles were used in every cycle. Results: After the IV characteristics were measured such as Voc, Isc, Pmax and fill factor, it shows that when higher annealing temperature of the profile was used, all the parameter will increase accordingly. However, profile with the highest annealing temperature will burn the paste as it will decrease the quality of the cell. This is considered as over heat to the paste. Conclusion: So by optimising the thermal treatment of the annealing process does improve the performance of the Si solar cell.

  10. Preparation of clean surfaces and Se vacancy formation in Bi2Se3 by ion bombardment and annealing

    Science.gov (United States)

    Zhou, Weimin; Zhu, Haoshan; Valles, Connie M.; Yarmoff, Jory A.

    2017-08-01

    Bismuth Selenide (Bi2Se3) is a topological insulator (TI) with a structure consisting of stacked quintuple layers. Single crystal surfaces are commonly prepared by mechanical cleaving. This work explores the use of low energy Ar+ ion bombardment and annealing (IBA) as an alternative method to produce reproducible and stable Bi2Se3 surfaces under ultra-high vacuum (UHV). It is found that a clean and well-ordered surface can be prepared by a single cycle of 1 keV Ar+ ion bombardment and 30 min of annealing. Low energy electron diffraction (LEED) and detailed low energy ion scattering (LEIS) measurements show no differences between IBA-prepared surfaces and those prepared by in situ cleaving in UHV. Analysis of the LEED patterns shows that the optimal annealing temperature is 450 °C. Angular LEIS scans reveal the formation of surface Se vacancies when the annealing temperature exceeds 520 °C.

  11. Improved characteristics of amorphous indium-gallium-zinc-oxide-based resistive random access memory using hydrogen post-annealing

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Dae Yun; Lee, Tae-Ho; Kim, Tae Geun, E-mail: tgkim1@korea.ac.kr [School of Electrical Engineering, Korea University, Seoul 02841 (Korea, Republic of)

    2016-08-15

    The authors report an improvement in resistive switching (RS) characteristics of amorphous indium-gallium-zinc-oxide (a-IGZO)-based resistive random access memory devices using hydrogen post-annealing. Because this a-IGZO thin film has oxygen off-stoichiometry in the form of deficient and excessive oxygen sites, the film properties can be improved by introducing hydrogen atoms through the annealing process. After hydrogen post-annealing, the device exhibited a stable bipolar RS, low-voltage set and reset operation, long retention (>10{sup 5 }s), good endurance (>10{sup 6} cycles), and a narrow distribution in each current state. The effect of hydrogen post-annealing is also investigated by analyzing the sample surface using X-ray photon spectroscopy and atomic force microscopy.

  12. Enhanced regeneration of degraded polymer solar cells by thermal annealing

    Science.gov (United States)

    Kumar, Pankaj; Bilen, Chhinder; Feron, Krishna; Zhou, Xiaojing; Belcher, Warwick J.; Dastoor, Paul C.

    2014-05-01

    The degradation and thermal regeneration of poly(3-hexylethiophene) (P3HT):[6,6]-phenyl-C61-butyric acid methyl ester (PCBM) and P3HT:indene-C60 bisadduct (ICBA) polymer solar cells, with Ca/Al and Ca/Ag cathodes and indium tin oxide/poly(ethylene-dioxythiophene):polystyrene sulfonate anode have been investigated. Degradation occurs via a combination of three primary pathways: (1) cathodic oxidation, (2) active layer phase segregation, and (3) anodic diffusion. Fully degraded devices were subjected to thermal annealing under inert atmosphere. Degraded solar cells possessing Ca/Ag electrodes were observed to regenerate their performance, whereas solar cells having Ca/Al electrodes exhibited no significant regeneration of device characteristics after thermal annealing. Moreover, the solar cells with a P3HT:ICBA active layer exhibited enhanced regeneration compared to P3HT:PCBM active layer devices as a result of reduced changes to the active layer morphology. Devices combining a Ca/Ag cathode and P3HT:ICBA active layer demonstrated ˜50% performance restoration over several degradation/regeneration cycles.

  13. Experimental and Numerical Simulations of Phase Transformations Occurring During Continuous Annealing of DP Steel Strips

    Science.gov (United States)

    Wrożyna, Andrzej; Pernach, Monika; Kuziak, Roman; Pietrzyk, Maciej

    2016-04-01

    Due to their exceptional strength properties combined with good workability the Advanced High-Strength Steels (AHSS) are commonly used in automotive industry. Manufacturing of these steels is a complex process which requires precise control of technological parameters during thermo-mechanical treatment. Design of these processes can be significantly improved by the numerical models of phase transformations. Evaluation of predictive capabilities of models, as far as their applicability in simulation of thermal cycles thermal cycles for AHSS is considered, was the objective of the paper. Two models were considered. The former was upgrade of the JMAK equation while the latter was an upgrade of the Leblond model. The models can be applied to any AHSS though the examples quoted in the paper refer to the Dual Phase (DP) steel. Three series of experimental simulations were performed. The first included various thermal cycles going beyond limitations of the continuous annealing lines. The objective was to validate models behavior in more complex cooling conditions. The second set of tests included experimental simulations of the thermal cycle characteristic for the continuous annealing lines. Capability of the models to describe properly phase transformations in this process was evaluated. The third set included data from the industrial continuous annealing line. Validation and verification of models confirmed their good predictive capabilities. Since it does not require application of the additivity rule, the upgrade of the Leblond model was selected as the better one for simulation of industrial processes in AHSS production.

  14. Stochastic annealing simulation of cascades in metals

    Energy Technology Data Exchange (ETDEWEB)

    Heinisch, H.L.

    1996-04-01

    The stochastic annealing simulation code ALSOME is used to investigate quantitatively the differential production of mobile vacancy and SIA defects as a function of temperature for isolated 25 KeV cascades in copper generated by MD simulations. The ALSOME code and cascade annealing simulations are described. The annealing simulations indicate that the above Stage V, where the cascade vacancy clusters are unstable,m nearly 80% of the post-quench vacancies escape the cascade volume, while about half of the post-quench SIAs remain in clusters. The results are sensitive to the relative fractions of SIAs that occur in small, highly mobile clusters and large stable clusters, respectively, which may be dependent on the cascade energy.

  15. Structural relaxation in annealed hyperquenched basaltic glasses

    DEFF Research Database (Denmark)

    Guo, Xiaoju; Mauro, John C.; Potuzak, M.

    2012-01-01

    The enthalpy relaxation behavior of hyperquenched (HQ) and annealed hyperquenched (AHQ) basaltic glass is investigated through calorimetric measurements. The results reveal a common onset temperature of the glass transition for all the HQ and AHQ glasses under study, indicating that the primary r...... relaxation is activated at the same temperature regardless of the initial departure from equilibrium. The analysis of secondary relaxation at different annealing temperatures provides insights into the enthalpy recovery of HQ glasses.......The enthalpy relaxation behavior of hyperquenched (HQ) and annealed hyperquenched (AHQ) basaltic glass is investigated through calorimetric measurements. The results reveal a common onset temperature of the glass transition for all the HQ and AHQ glasses under study, indicating that the primary...

  16. Thermal annealing of thin PECVD silicon-oxide films for airgap-based optical filters

    Science.gov (United States)

    Ghaderi, M.; de Graaf, G.; Wolffenbuttel, R. F.

    2016-08-01

    This paper investigates the mechanical and optical properties of thin PECVD silicon-oxide layers for optical applications. The different deposition parameters in PECVD provide a promising tool to manipulate and control the film structure. Membranes for use in optical filters typically are of ~λ/4n thickness and should be slightly tensile for remaining flat, thus avoiding scattering. The effect of the thermal budget of the process on the mechanical characteristics of the deposited films was studied. Films with compressive stress ranging from  -100 to 0 MPa were deposited. Multiple thermal annealing cycles were applied to wafers and the in situ residual stress and ex situ optical properties were measured. The residual stress in the films was found to be highly temperature dependent. Annealing during the subsequent process steps results in tensile stress from 100 to 300 MPa in sub-micron thick PECVD silicon-oxide films. However, sub-100 nm thick PECVD silicon-oxide layers exhibit a lower dependence on the thermal annealing cycles, resulting in lower stress variations in films after the annealing. It is also shown that the coefficient of thermal expansion, hence the residual stress in layers, varies with the thickness. Finally, several free-standing membranes were fabricated and the results are compared.

  17. Quantum annealing correction with minor embedding

    Science.gov (United States)

    Vinci, Walter; Albash, Tameem; Paz-Silva, Gerardo; Hen, Itay; Lidar, Daniel A.

    2015-10-01

    Quantum annealing provides a promising route for the development of quantum optimization devices, but the usefulness of such devices will be limited in part by the range of implementable problems as dictated by hardware constraints. To overcome constraints imposed by restricted connectivity between qubits, a larger set of interactions can be approximated using minor embedding techniques whereby several physical qubits are used to represent a single logical qubit. However, minor embedding introduces new types of errors due to its approximate nature. We introduce and study quantum annealing correction schemes designed to improve the performance of quantum annealers in conjunction with minor embedding, thus leading to a hybrid scheme defined over an encoded graph. We argue that this scheme can be efficiently decoded using an energy minimization technique provided the density of errors does not exceed the per-site percolation threshold of the encoded graph. We test the hybrid scheme using a D-Wave Two processor on problems for which the encoded graph is a two-level grid and the Ising model is known to be NP-hard. The problems we consider are frustrated Ising model problem instances with "planted" (a priori known) solutions. Applied in conjunction with optimized energy penalties and decoding techniques, we find that this approach enables the quantum annealer to solve minor embedded instances with significantly higher success probability than it would without error correction. Our work demonstrates that quantum annealing correction can and should be used to improve the robustness of quantum annealing not only for natively embeddable problems but also when minor embedding is used to extend the connectivity of physical devices.

  18. Enhanced piecewise regression based on deterministic annealing

    Institute of Scientific and Technical Information of China (English)

    ZHANG JiangShe; YANG YuQian; CHEN XiaoWen; ZHOU ChengHu

    2008-01-01

    Regression is one of the important problems in statistical learning theory. This paper proves the global convergence of the piecewise regression algorithm based on deterministic annealing and continuity of global minimum of free energy w.r.t temperature, and derives a new simplified formula to compute the initial critical temperature. A new enhanced piecewise regression algorithm by using "migration of prototypes" is proposed to eliminate "empty cell" in the annealing process. Numerical experiments on several benchmark datasets show that the new algo-rithm can remove redundancy and improve generalization of the piecewise regres-sion model.

  19. Effect of annealing temperature on wettability of TiO2 nanotube array films

    Science.gov (United States)

    2014-01-01

    Highly ordered TiO2 nanotube array (TN) films were prepared by anodization of titanium foil in a mixed electrolyte solution of glycerin and NH4F and then annealed at 200°C, 400°C, 600°C, and 800°C, respectively. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), water contact angle (WCA), and photoluminescence (PL). It was found that low temperature (below 600°C) has no significant influence on surface morphology, but the diameter of the nanotube increases from 40 to 50 nm with increasing temperature. At 800°C, the nanotube arrays are completely destroyed and only dense rutile film is observed. Samples unannealed and annealed at 200°C are amorphous. At 400°C, anatase phase appears. At 600°C, rutile phase appears. At 800°C, anatase phase changes into rutile phase completely. The wettability of the TN films shows that the WCAs for all samples freshly annealed at different temperatures are about 0°. After the annealed samples have been stored in air for 1 month, the WCAs increase to 130°, 133°, 135°, 141°, and 77°, respectively. Upon ultraviolet (UV) irradiation, they exhibit a significant transition from hydrophobicity to hydrophilicity. Especially, samples unannealed and annealed at 400°C show high photoinduced hydrophilicity. PMID:25426006

  20. The Performance of CSAM SAM when Cycle Length is extended

    Energy Technology Data Exchange (ETDEWEB)

    Roh, Kyung-ho; Moon, Sang-rae [KHNP, Daejeon (Korea, Republic of)

    2016-10-15

    In order to verify validation of that, CPC Axial Power Distribution is compared with Axial Power Distribution based on ICI every week. The difference between CPC Axial Power Distribution and Axial Power Distribution based on ICI increases according as fuels are burned. It is called CPC Axial Power Distribution Root Mean Square Error (CPC RMS Error). SAM and calibration of ex-core detector are important factors influencing the magnitude of the difference. According to vendor, the difference is limited by 8%. Otherwise, CPC penalty increases as many as difference increase. Therefore, KHNP developed Constrained Simulated Annealing Method (CSAM), which has better performance than that of Least Square Method (LSM), to calculate SAM constant. The CSA SAM contributed largely to maintain CPC operating margin. Somewhat, KHNP is developing the technology to be able to operate nuclear power plants for 24 month to optimize their efficiency. This paper shows trends of CPC RMS Error in a case of 24 months operation. Trends are based on data of a few OPR1000s under operation. It is data of OPR1000s that CSA SAM is applied. KHNP is developing the technology to extend operation cycle length in order to optimize the operation efficiency of OPR1000. To verify effect of extended operation cycle length on CPC, CPC Axial Power Distribution RMS Error in a case of 24 months operation was expected using operation data of six cycles in OPR1000. In cases that CPC Axial Power Distribution RMS Error exceeds threshold, operation margin is decreased due to CPC penalty. To prevent CPC operation margin from being decreased, improved method to calculate SAM or to calibrate ex-core detector is required. KHNP will consider the way to maintain CPC operation margin along with 24 month operation technology development, hereafter.

  1. Annealing study of a bistable cluster defect

    Energy Technology Data Exchange (ETDEWEB)

    Junkes, Alexandra, E-mail: alexandra.junkes@desy.d [Institute for Experimental Physics, University of Hamburg, 22761 Hamburg (Germany); Eckstein, Doris [Institute for Experimental Physics, University of Hamburg, 22761 Hamburg (Germany); Pintilie, Ioana [Institute for Experimental Physics, University of Hamburg, 22761 Hamburg (Germany); NIMP Bucharest-Margurele (Romania); Makarenko, Leonid F. [Belarusian State University, Minsk (Belarus); Fretwurst, Eckhart [Institute for Experimental Physics, University of Hamburg, 22761 Hamburg (Germany)

    2010-01-11

    This work deals with the influence of neutron and proton induced cluster related defects on the properties of n-type silicon detectors. Defect concentrations were obtained by means of Deep Level Transient Spectroscopy (DLTS) and Thermally Stimulated Current (TSC) technique, while the full depletion voltage and the reverse current were extracted from capacitance-voltage (C-V) and current-voltage (I-V) characteristics. The annealing behaviour of the reverse current can be correlated with the annealing of the cluster related defect levels labeled E4a and E4b by making use of their bistability. This bistability was characterised by isochronal and isothermal annealing studies and it was found that the development with increasing annealing temperature is similar to that of divacancies. This supports the assumption that E4a and E4b are vacancy related defects. In addition we observe an influence of the disordered regions on the shape and height of the DLTS or TSC signals corresponding to point defects like the vacancy-oxygen complex.

  2. Thermal annealing in neutron-irradiated tribromobenzenes

    DEFF Research Database (Denmark)

    Siekierska, K.E.; Halpern, A.; Maddock, A. G.

    1968-01-01

    The distribution of 82Br among various products in neutron-irradiated isomers of tribromobenzene has been investigated, and the effect of thermal annealing examined. Reversed-phase partition chromatography was employed for the determination of radioactive organic products, and atomic bromine...

  3. In-situ grazing incidence X-ray diffraction measurements of relaxation in Fe/MgO/Fe epitaxial magnetic tunnel junctions during annealing

    Science.gov (United States)

    Eastwood, D. S.; Ali, M.; Hickey, B. J.; Tanner, B. K.

    2013-12-01

    The relaxation of Fe/MgO/Fe tunnel junctions grown epitaxially on (001) MgO substrates has been measured by in-situ grazing incidence in-plane X-ray diffraction during the thermal annealing cycle. We find that the Fe layers are fully relaxed and that there are no irreversible changes during annealing. The MgO tunnel barrier is initially strained towards the Fe but on annealing, relaxes and expands towards the bulk MgO value. The strain dispersion is reduced in the MgO by about 40% above 480 K post-annealing. There is no significant change in the "twist" mosaic. Our results indicate that the final annealing stage of device fabrication, crucial to attainment of high TMR, induces substantial strain relaxation at the MgO barrier/lower Fe electrode interface.

  4. Influence of time of annealing on anneal hardening effect of a cast CuZn alloy

    Directory of Open Access Journals (Sweden)

    Nestorović Svetlana

    2003-01-01

    Full Text Available Investigated cast copper alloy containing 8at%Zn of a solute. For comparison parallel specimens made from cast pure copper. Copper and copper alloy were subjected to cold rolling with different a final reduction of 30,50 and 70%. The cold rolled copper and copper alloy samples were isochronally and isothermally annealed up to recrystallization temperature. After that the values of hardness, strength and electrical conductivity were measured and X-ray analysis was performed. These investigations show that anneal hardening effect at alloys was attained under recrystallization temperature in the temperature range of 180-3000C, followed with an increase in hardness. The amount of strengthening increase with increasing degree of prior cold work. Also the X-ray analysis show the change of lattice parameter during annealing when anneal hardening effect was attained.

  5. Through-vial impedance spectroscopy of the mechanisms of annealing in the freeze-drying of maltodextrin: the impact of annealing hold time and temperature on the primary drying rate.

    Science.gov (United States)

    Smith, Geoff; Arshad, Muhammad Sohail; Polygalov, Eugene; Ermolina, Irina

    2014-06-01

    The study aims to investigate the impact of annealing hold time and temperature on the primary drying rate/duration of a 10% (w/v) solution of maltodextrin with an emphasis on how the mechanisms of annealing might be understood from the in-vial measurements of the ice crystal growth and the glass transition. The electrical impedance of the solution within a modified glass vial was recorded between 10 and 10(6) Hz during freeze-drying cycles with varying annealing hold times (1-5 h) and temperatures. Primary drying times decreased by 7%, 27% and 34% (1.1, 4.3 and 5.5 h) with the inclusion of an annealing step at temperatures of -15°C, -10°C and -5°C, respectively. The glass transition was recorded at approximately -16°C during the re-heating and re-cooling steps, which is close to the glass transition (Tg ') reported for 10% (w/v) maltodextrin and therefore indicates that a maximum freeze concentration (∼86%, w/w, from the Gordon-Taylor equation) was achieved during first freezing, with no further ice being formed on annealing. This observation, coupled to the decrease in electrical resistance that was observed during the annealing hold time, suggests that the reduction in the drying time was because of improved connectivity of ice crystals because of Ostwald ripening rather than devitrification.

  6. Monthly Weather Review

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Supplements to the Monthly Weather Review publication. The Weather Bureau published the Monthly weather review Supplement irregularly from 1914 to 1949. The...

  7. Proposing Chinese Pharmacists Month

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    @@ Dear Pharmacists: Today I would like to share with you about the American Pharmacists Month which is celebrated in October every year.This month-long observance is promoted by American Pharmacist Association.

  8. An Effect of Annealing on Shielding Properties of Shungite

    Science.gov (United States)

    Belousova, E. S.; Mahmoud, M. Sh.; Lynkou, L. M.

    2013-05-01

    Annealing of shungite is studied in oxidizing conditions in a chamber with NH4Cl, and in vacuum at 900 °C for 2h. Frequency dependencies of transmission and reflection coefficients of annealed shungite are measured in the frequency range of 8-12 GHz. The minimum reflection at 8-10 GHz was shown for shungite annealed in the oxidizing atmosphere.

  9. Hysteresis in Lanthanide Zirconium Oxides Observed Using a Pulse CV Technique and including the Effect of High Temperature Annealing

    Directory of Open Access Journals (Sweden)

    Qifeng Lu

    2015-07-01

    Full Text Available A powerful characterization technique, pulse capacitance-voltage (CV technique, was used to investigate oxide traps before and after annealing for lanthanide zirconium oxide thin films deposited on n-type Si (111 substrates at 300 °C by liquid injection Atomic Layer Deposition (ALD. The results indicated that: (1 more traps were observed compared to the conventional capacitance-voltage characterization method in LaZrOx; (2 the time-dependent trapping/de-trapping was influenced by the edge time, width and peak-to-peak voltage of a gate voltage pulse. Post deposition annealing was performed at 700 °C, 800 °C and 900 °C in N2 ambient for 15 s to the samples with 200 ALD cycles. The effect of the high temperature annealing on oxide traps and leakage current were subsequently explored. It showed that more traps were generated after annealing with the trap density increasing from 1.41 × 1012 cm−2 for as-deposited sample to 4.55 × 1012 cm−2 for the 800 °C annealed one. In addition, the leakage current density increase from about 10−6 A/cm2 at Vg = +0.5 V for the as-deposited sample to 10−3 A/cm2 at Vg = +0.5 V for the 900 °C annealed one.

  10. Menstrual Cycle

    Science.gov (United States)

    ... Luteal (after egg release) Changes During the Menstrual Cycle The menstrual cycle is regulated by the complex interaction of ... egg release) Luteal (after egg release) The menstrual cycle begins with menstrual bleeding (menstruation), which marks the first day of ...

  11. Simulation in 3 dimensions of a cycle 18 months for an BWR type reactor using the Nod3D program; Simulacion en 3 dimensiones de un ciclo de 18 meses para un reactor BWR usando el programa Nod3D

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez, N.; Alonso, G. [ININ, A.P. 18-1027, 11801 Mexico D.F. (Mexico)]. E-mail: nhm@nuclear.inin.mx; Valle, E. del [IPN, ESFM, 07738 Mexico D.F. (Mexico)

    2004-07-01

    The development of own codes that you/they allow the simulation in 3 dimensions of the nucleus of a reactor and be of easy maintenance, without the consequent payment of expensive use licenses, it can be a factor that propitiates the technological independence. In the Department of Nuclear Engineering (DIN) of the Superior School of Physics and Mathematics (ESFM) of the National Polytechnic Institute (IPN) a denominated program Nod3D has been developed with the one that one can simulate the operation of a reactor BWR in 3 dimensions calculating the effective multiplication factor (kJJ3, as well as the distribution of the flow neutronic and of the axial and radial profiles of the power, inside a means of well-known characteristics solving the equations of diffusion of neutrons numerically in stationary state and geometry XYZ using the mathematical nodal method RTN0 (Raviart-Thomas-Nedelec of index zero). One of the limitations of the program Nod3D is that it doesn't allow to consider the burnt of the fuel in an independent way considering feedback, this makes it in an implicit way considering the effective sections in each step of burnt and these sections are obtained of the code Core Master LEND. However even given this limitation, the results obtained in the simulation of a cycle of typical operation of a reactor of the type BWR are similar to those reported by the code Core Master LENDS. The results of the keJ - that were obtained with the program Nod3D they were compared with the results of the code Core Master LEND, presenting a difference smaller than 0.2% (200 pcm), and in the case of the axial profile of power, the maxim differs it was of 2.5%. (Author)

  12. Synthesis of copper nanoparticles in a fluoropolymer matrix by annealing in vacuum

    Science.gov (United States)

    Safonov, Alexey; Sulyaeva, Veronica; Timoshenko, Nikolay; Starinskiy, Sergey

    2017-07-01

    In this paper, a method for synthesizing copper nanoparticles in a fluoropolymer matrix is proposed which prevents the reduction in the plasmonic properties due to the oxidation of the metal. The basic idea of the proposed method of nanoparticle synthesis is to anneal of thin metal film coated with a thin layer of fluoropolymer. The morphology and optical properties of the resulting composites were determined. The optical properties remained unchanged after several months of storage under standard conditions.

  13. Optimization Via Open System Quantum Annealing

    Science.gov (United States)

    2016-01-07

    Error corrected quantum annealing with hundreds of qubits, (07 2013) Siddhartha Santra, Gregory Quiroz , Greg Ver Steeg, Daniel Lidar. MAX 2-SAT...Zhihui Wang, Tameem Albash, Iman Marvian, and Walter Vinci Graduate Students: Gregory Quiroz , Kristen Pudenz, Anurag Mishra, Milad Marvian... Quiroz , G. Ver Steeg, D.A. Lidar, “MAX 2-SAT with up to 108 qubits”, New J. Phys. 16, 045006 (2014). 20. S. Boixo, T. Ronnow, S. Isakov, Z. Wang

  14. Simulated annealing algorithm for optimal capital growth

    Science.gov (United States)

    Luo, Yong; Zhu, Bo; Tang, Yong

    2014-08-01

    We investigate the problem of dynamic optimal capital growth of a portfolio. A general framework that one strives to maximize the expected logarithm utility of long term growth rate was developed. Exact optimization algorithms run into difficulties in this framework and this motivates the investigation of applying simulated annealing optimized algorithm to optimize the capital growth of a given portfolio. Empirical results with real financial data indicate that the approach is inspiring for capital growth portfolio.

  15. Annealing free magnetic tunnel junction sensors

    Science.gov (United States)

    Knudde, S.; Leitao, D. C.; Cardoso, S.; Freitas, P. P.

    2017-04-01

    Annealing is a major step in the fabrication of magnetic tunnel junctions (MTJs). It sets the exchange bias between the pinned and antiferromagnetic layers, and helps to increase the tunnel magnetoresistance (TMR) in both amorphous and crystalline junctions. Recent research on MTJs has focused on MgO-based structures due to their high TMR. However, the strict process control and mandatory annealing step can limit the scope of the application of these structures as sensors. In this paper, we present AlOx-based MTJs that are produced by ion beam sputtering and remote plasma oxidation and show optimum transport properties with no annealing. The microfabricated devices show TMR values of up to 35% and using NiFe/CoFeB free layers provides tunable linear ranges, leading to coercivity-free linear responses with sensitivities of up to 5.5%/mT. The top-pinned synthetic antiferromagnetic reference shows a stability of about 30 mT in the microfabricated devices. Sensors with linear ranges of up to 60 mT are demonstrated. This paves the way for the integration of MTJ sensors in heat-sensitive applications such as flexible substrates, or for the design of low-footprint on-chip multiaxial sensing devices.

  16. Simulated annealing with probabilistic analysis for solving traveling salesman problems

    Science.gov (United States)

    Hong, Pei-Yee; Lim, Yai-Fung; Ramli, Razamin; Khalid, Ruzelan

    2013-09-01

    Simulated Annealing (SA) is a widely used meta-heuristic that was inspired from the annealing process of recrystallization of metals. Therefore, the efficiency of SA is highly affected by the annealing schedule. As a result, in this paper, we presented an empirical work to provide a comparable annealing schedule to solve symmetric traveling salesman problems (TSP). Randomized complete block design is also used in this study. The results show that different parameters do affect the efficiency of SA and thus, we propose the best found annealing schedule based on the Post Hoc test. SA was tested on seven selected benchmarked problems of symmetric TSP with the proposed annealing schedule. The performance of SA was evaluated empirically alongside with benchmark solutions and simple analysis to validate the quality of solutions. Computational results show that the proposed annealing schedule provides a good quality of solution.

  17. Diurnal Cycle Computations

    Energy Technology Data Exchange (ETDEWEB)

    Covey, Curt [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Doutriaux, Charles [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-12-01

    Directory /export_backup/covey1/CMIP5/Precipitation/DiurnalCycle/GridpointTimeseries/CMCCBCM_etal/ on crunchy.llnl.gov contains Python / UV-CDAT scripts compositeDiurnalStatistics.py and fourierDiurB nalAllGrid.py. compositeDiurnalStatistics.py reads high-time-frequency climate data from one or more years and computes 24 hour composite-mean and composite-standard-deviation cycles for one requested month.

  18. Effect of the Solution Annealing and Chemical Passivation Followed by Aging on the Corrosion of Shell Mold Cast CF8 Stainless Steel

    Science.gov (United States)

    Kim, Kuk-Jin; Ju, Heongkyu; Moon, Young-Dae; Hong, Jun Ho; Pak, Sung Joon

    2016-10-01

    The effects of solution annealing and passivation of shell mold cast CF8 stainless steels on Elbow pipe fittings with 2-month room temperature aging have been studied using a corrosion technique. The resistance of corrosion increased with 2-month room temperature aging combined with solid solution annealing and chemical passivation. The mode of corrosion was deeply related to the δ-ferrite content, permeability, and passivation. The corrosion probability decreased as both the δ-ferrite content and the permeability decreased. Therefore, it is considered that δ-ferrite content and passive film of Cr2O3 play an important role in corrosion resistance of CF8 Elbow pipe fittings due to the long-term aging with solid solution annealing and chemical passivation. This result shows that the corrosion resistance of CF8 fittings can be enhanced by the solid solution annealing and chemical passivation. Decreased ferrite phases and permeability improve IGC resistance in CF8 steel.

  19. Comparing Monte Carlo methods for finding ground states of Ising spin glasses: Population annealing, simulated annealing, and parallel tempering

    Science.gov (United States)

    Wang, Wenlong; Machta, Jonathan; Katzgraber, Helmut G.

    2015-07-01

    Population annealing is a Monte Carlo algorithm that marries features from simulated-annealing and parallel-tempering Monte Carlo. As such, it is ideal to overcome large energy barriers in the free-energy landscape while minimizing a Hamiltonian. Thus, population-annealing Monte Carlo can be used as a heuristic to solve combinatorial optimization problems. We illustrate the capabilities of population-annealing Monte Carlo by computing ground states of the three-dimensional Ising spin glass with Gaussian disorder, while comparing to simulated-annealing and parallel-tempering Monte Carlo. Our results suggest that population annealing Monte Carlo is significantly more efficient than simulated annealing but comparable to parallel-tempering Monte Carlo for finding spin-glass ground states.

  20. Comparing Monte Carlo methods for finding ground states of Ising spin glasses: Population annealing, simulated annealing, and parallel tempering.

    Science.gov (United States)

    Wang, Wenlong; Machta, Jonathan; Katzgraber, Helmut G

    2015-07-01

    Population annealing is a Monte Carlo algorithm that marries features from simulated-annealing and parallel-tempering Monte Carlo. As such, it is ideal to overcome large energy barriers in the free-energy landscape while minimizing a Hamiltonian. Thus, population-annealing Monte Carlo can be used as a heuristic to solve combinatorial optimization problems. We illustrate the capabilities of population-annealing Monte Carlo by computing ground states of the three-dimensional Ising spin glass with Gaussian disorder, while comparing to simulated-annealing and parallel-tempering Monte Carlo. Our results suggest that population annealing Monte Carlo is significantly more efficient than simulated annealing but comparable to parallel-tempering Monte Carlo for finding spin-glass ground states.

  1. Hispanic Heritage Month

    Science.gov (United States)

    York, Sherry

    2004-01-01

    Hispanic heritage month is from September 15 to October 15. One problem that arises when grouping people into categories such as Hispanic or Latino is stereotyping, stereotypes can be promoted or used in this Hispanic month to promote a greater understanding of Latino cultures.

  2. Progress report, 24 months

    DEFF Research Database (Denmark)

    Juhl, Thomas Winther; Nielsen, Jakob Skov

    The work performed during the past 12 months (months 13 – 24) of the project has included the conclusion of Task 1 – Fundamental Studies and Task 2 – Multimirror Cutting Head Design. Work on Task 3 – Compact Cutting Head Design, and Task 4 – Interface Design has been carried out and the tests...... of the multimirror cutting head have been started....

  3. Progress report, 36 months

    DEFF Research Database (Denmark)

    Juhl, Thomas Winther; Nielsen, Jakob Skov

    The work performed during the past 12 months (months 13 – 24) of the project has included the conclusion of Task 1 – Fundamental Studies and Task 2 – Multimirror Cutting Head Design. Work on Task 3 – Compact Cutting Head Design, and Task 4 – Interface Design has been carried out and the tests...... of the multimirror cutting head have been started....

  4. Progress report, 36 months

    DEFF Research Database (Denmark)

    Juhl, Thomas Winther; Nielsen, Jakob Skov

    The work performed during the past 12 months (months 13 – 24) of the project has included the conclusion of Task 1 – Fundamental Studies and Task 2 – Multimirror Cutting Head Design. Work on Task 3 – Compact Cutting Head Design, and Task 4 – Interface Design has been carried out and the tests of ...

  5. Progress report, 24 months

    DEFF Research Database (Denmark)

    Juhl, Thomas Winther; Nielsen, Jakob Skov

    The work performed during the past 12 months (months 13 – 24) of the project has included the conclusion of Task 1 – Fundamental Studies and Task 2 – Multimirror Cutting Head Design. Work on Task 3 – Compact Cutting Head Design, and Task 4 – Interface Design has been carried out and the tests of ...

  6. Reconciling historical and contemporary evidence of aeolian-based, gully annealing processes in Glen, Marble, and Grand Canyon, USA

    Science.gov (United States)

    Sankey, J. B.; Draut, A. E.

    2013-12-01

    In the absence of large Colorado River floods in Glen, Marble, and Grand Canyons since the completion of Glen Canyon Dam, the geomorphic process most able to counteract the effects of gully incision on terraces and slopes above the contemporary active Colorado River channel is aeolian sand transport that can partially or entirely fill (anneal) small gullies. Whereas gully-formation processes have been much studied, relatively little is known about processes of gully annealing. Aeolian-based annealing has been observed in several instances in the modern Colorado River corridor operating on time scales of months. However, individual, short-term occurrences of aeolian deposition that counteract gully erosion have not yet been expanded into a landscape-scale evaluation of the prevalence of gully-annealing processes over longer time scales (years-decades) along the post-dam corridor. The extent that aeolian or other annealing processes might slow, or temporarily reverse, gully incision and erosion is important in this system because of the propensity for erosion damage to locations of cultural significance that are extensive on terraces and slopes above the contemporary active Colorado River channel. Moreover, the reduction of mainstem fluvial sediment inputs to the system since completion of Glen Canyon Dam might impact the potential of aeolian redistribution of Colorado River-derived sediment as an effective gully annealing mechanism on upper slopes and terraces. We present an investigation of the extent that observations of (i) historical annealing and (ii) contemporary annealing potential, reconcile with (iii) literature and/or model-based estimates of relative rates of gully formation and aeolian deposition in this system. The central question of this work is whether these complimentary lines of evidence support aeolian infilling as a viable mechanism for annealing gullies in Glen, Marble, and Grand Canyons, and analogous systems. We examine the evidence for

  7. Studies on forming gas annealing treated BiFeO3 thin films and capacitors

    Science.gov (United States)

    Lee, Chia-Ching; Wu, Lin-Jung; Wu, Jenn-Ming

    2007-11-01

    The structure and electric properties of BiFeO3(BFO )/BaPbO3(BPO) and Pt/BFO/BPO capacitors with forming gas annealing (FGA) treatment were investigated. X-ray diffraction patterns indicated that the annealing did not affect the structure and phase of BFO films. A degraded electric property was obtained in FGA-treated Pt/BFO/BPO films. It can be attributed to the formation of reduction and incomplete reduction of Bi+3 of BFO. Retention and fatigue properties were obtained in FGA-treated BPO/BFO/BPO capacitors. The normalized Pr loss was 22.8% after applying a voltage above 2Vc (coercive voltage) with 1011cycles. The retention behavior within 30000s is governed by the logarithmic time dependence.

  8. Pulse-plating electrodeposition and annealing treatment of CuInSe2 films

    Institute of Scientific and Technical Information of China (English)

    LIU Fang-yang; L(U) Ying; ZHANG Zhi-an; LAI Yan-qing; LI Jie; LIU Ye-xiang

    2008-01-01

    CuInSe2 (CIS) thin film was prepared on molybdenum substrate using pulse-plating electrodeposition in aqueous solution. The most suitable pulse potential range for co-deposition is found to be from -0.55 to -0.75 V (vs SCE) from linear potential scanning curve. The electrodeposited films were characterized by X-ray diffractometry (XRD), scanning electron microscopy(SEM) and energy dispersive X-ray analysis (EDS). The annealing effects on electrodeposited precursors were investigated. And the influence of pulse parameters on film quality was studied. The chalcopyrite phase CuInSe2 films with smooth surface and stoichiometric composition are obtained at a pulse potential from -0.65 to -0.7 V (vs SCE), a pulse period of 1-9 ms with a duty cycle of 33% and annealing treatment.

  9. Shortcuts to adiabaticity for quantum annealing

    Science.gov (United States)

    Takahashi, Kazutaka

    2017-01-01

    We study the Ising Hamiltonian with a transverse field term to simulate the quantum annealing. Using shortcuts to adiabaticity, we design the time dependence of the Hamiltonian. The dynamical invariant is obtained by the mean-field ansatz, and the Hamiltonian is designed by the inverse engineering. We show that the time dependence of physical quantities such as the magnetization is independent of the speed of the Hamiltonian variation in the infinite-range model. We also show that rotating transverse magnetic fields are useful to achieve the ideal time evolution.

  10. Computational Multiqubit Tunnelling in Programmable Quantum Annealers

    Science.gov (United States)

    2016-08-25

    annealing of a 16-qubit problem. Nat. Commun. 4, 1903 (2013). 13. McGeoch, C. C. & Wang, C. in Proceedings of the ACM International Conference on...Computing Frontiers 23 ( ACM , 2013). 14. Dash, S. A note on qubo instances defined on chimera graphs. Preprint at http://arxiv.org/abs/1306.1202 (2013...B. W. in Proceedings of the Thirty-Sixth Annual ACM Symposium on Theory of Computing 502–510 (New York, NY, USA, 2004). 33. Somma, R. D., Boixo, S

  11. Binary Sparse Phase Retrieval via Simulated Annealing

    Directory of Open Access Journals (Sweden)

    Wei Peng

    2016-01-01

    Full Text Available This paper presents the Simulated Annealing Sparse PhAse Recovery (SASPAR algorithm for reconstructing sparse binary signals from their phaseless magnitudes of the Fourier transform. The greedy strategy version is also proposed for a comparison, which is a parameter-free algorithm. Sufficient numeric simulations indicate that our method is quite effective and suggest the binary model is robust. The SASPAR algorithm seems competitive to the existing methods for its efficiency and high recovery rate even with fewer Fourier measurements.

  12. Interference Alignment Using Variational Mean Field Annealing

    DEFF Research Database (Denmark)

    Badiu, Mihai Alin; Guillaud, Maxime; Fleury, Bernard Henri

    2014-01-01

    We study the problem of interference alignment in the multiple-input multiple- output interference channel. Aiming at minimizing the interference leakage power relative to the receiver noise level, we use the deterministic annealing approach to solve the optimization problem. In the corresponding...... for interference alignment. We also show that the iterative leakage minimization algorithm by Gomadam et al. and the alternating minimization algorithm by Peters and Heath, Jr. are instances of our method. Finally, we assess the performance of the proposed algorithm through computer simulations....

  13. TARP Monthly Housing Scorecard

    Data.gov (United States)

    Department of the Treasury — Treasury and the U.S. Department of Housing and Urban Development (HUD) jointly produce a Monthly Housing Scorecard on the health of the nation’s housing market. The...

  14. Lightship Monthly Observations

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Daily Weather Observations (Monthly Form 1001) from lightship stations in the United States. Please see the 'Surface Weather Observations (1001)' library for more...

  15. Oceanographic Monthly Summary

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Oceanographic Monthly Summary contains sea surface temperature (SST) analyses on both regional and ocean basin scales for the Atlantic, Pacific, and Indian Oceans....

  16. Biogeochemical Cycling

    Science.gov (United States)

    Bebout, Brad; Fonda, Mark (Technical Monitor)

    2002-01-01

    This lecture will introduce the concept of biogeochemical cycling. The roles of microbes in the cycling of nutrients, production and consumption of trace gases, and mineralization will be briefly introduced.

  17. Preparation and Thermal Characterization of Annealed Gold Coated Porous Silicon

    Directory of Open Access Journals (Sweden)

    Afarin Bahrami

    2012-01-01

    Full Text Available Porous silicon (PSi layers were formed on a p-type Si wafer. Six samples were anodised electrically with a 30 mA/cm2 fixed current density for different etching times. The samples were coated with a 50–60 nm gold layer and annealed at different temperatures under Ar flow. The morphology of the layers, before and after annealing, formed by this method was investigated by scanning electron microscopy (SEM. Photoacoustic spectroscopy (PAS measurements were carried out to measure the thermal diffusivity (TD of the PSi and Au/PSi samples. For the Au/PSi samples, the thermal diffusivity was measured before and after annealing to study the effect of annealing. Also to study the aging effect, a comparison was made between freshly annealed samples and samples 30 days after annealing.

  18. Study on thermal annealing of cadmium zinc telluride (CZT) crystals

    Energy Technology Data Exchange (ETDEWEB)

    Yang, G.; Bolotnikov, A.E.; Fochuk, P.M.; Camarda, G.S.; Cui, Y.; Hossain, A.; Kim, K.; Horace, J.; McCall, B.; Gul, R.; Xu, L.; Kopach, O.V.; and James, R.B.

    2010-08-01

    Cadmium Zinc Telluride (CZT) has attracted increasing interest with its promising potential as a room-temperature nuclear-radiation-detector material. However, different defects in CZT crystals, especially Te inclusions and dislocations, can degrade the performance of CZT detectors. Post-growth annealing is a good approach potentially to eliminate the deleterious influence of these defects. At Brookhaven National Laboratory (BNL), we built up different facilities for investigating post-growth annealing of CZT. Here, we report our latest experimental results. Cd-vapor annealing reduces the density of Te inclusions, while large temperature gradient promotes the migration of small-size Te inclusions. Simultaneously, the annealing lowers the density of dislocations. However, only-Cd-vapor annealing decreases the resistivity, possibly reflecting the introduction of extra Cd in the lattice. Subsequent Te-vapor annealing is needed to ensure the recovery of the resistivity after removing the Te inclusions.

  19. Effect of current annealing on electronic properties of multilayer graphene

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, S; Goto, H; Tomori, H; Kanda, A [Institute of Physics, University of Tsukuba, Tsukuba 305-8571 (Japan); Ootuka, Y [Tsukuba Research Center for Interdisciplinary Materials Science (TIMS), University of Tsukuba, Tsukuba 305-8571 (Japan); Tsukagoshi, K, E-mail: tanaka@lt.px.tsukuba.ac.j [MANA, NIMS, Namiki, Tsukuba, Ibaraki 305-0047 (Japan)

    2010-06-01

    While ideal graphene has high mobility due to the relativistic nature of carriers, it is known that the carrier transport in actual graphene samples is dominated by the influence of scattering from charged impurities, which almost conceals the intrinsic splendid properties of this novel material. The common techniques to improve the graphene mobility include the annealing in hydrogen atmosphere and the local annealing by imposing a large biasing current. Although annealing is quite important technique for the experimental study of graphene, detailed evaluation of the annealing effect is lacking at present. In this paper, we study the effect of the current annealing in multilayer graphene devices quantitatively by investigating the change in the mobility and the carrier density at the charge neutrality point. We find that the current annealing sometimes causes degradation of the transport properties.

  20. Annealing effect and stability of carbon nanotubes in hydrogen flame

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Annealing of carbon nanotubes (CNTs) by the hydrogen flame in air was investigated in this study. Raman spectroscopy and scanning electron microscopy were used to characterize the products. The peak width of Raman spectra decreased with the increase in the annealing time. The CNTs were not stable in the hydrogen flame and the etching rate of the CNTs by hydrogen flame was very high. The hydrogen flame annealing had some effects on improving the crystallinity of CNTs.

  1. Annealing-induced Grain Refinement in a Nanostructured Ferritic Steel

    Institute of Scientific and Technical Information of China (English)

    Limin Wang; Zhenbo Wangt; Sheng Guo; Ke Lu

    2012-01-01

    A nanostructured surface layer with a mean ferrite grain size of -8 nm was produced on a Fe-gCr steel by means of surface mechanical attrition treatment. Upon annealing, ferrite grains coarsen with increasing temperature and their sizes increase to -40 nm at 973 K. Further increasing annealing temperature leads to an obvious reduction of ferrite grain sizes, to -14 nm at 1173 K. The annealing-induced grain refinement is analyzed in terms of phase transformations in the nanostructured steel.

  2. Human pose tracking by parametric annealing

    CERN Document Server

    Kaliamoorthi, Prabhu

    2012-01-01

    Model based methods to marker-free motion capture have a very high computational overhead that make them unattractive. In this paper we describe a method that improves on existing global optimization techniques to tracking articulated objects. Our method improves on the state-of-the-art Annealed Particle Filter (APF) by reusing samples across annealing layers and by using an adaptive parametric density for diffusion. We compare the proposed method with APF on a scalable problem and study how the two methods scale with the dimensionality, multi-modality and the range of search. Then we perform sensitivity analysis on the parameters of our algorithm and show that it tolerates a wide range of parameter settings. We also show results on tracking human pose from the widely-used Human Eva I dataset. Our results show that the proposed method reduces the tracking error despite using less than 50% of the computational resources as APF. The tracked output also shows a significant qualitative improvement over APF as dem...

  3. Energy conservation in cupolas and annealing furnaces

    Energy Technology Data Exchange (ETDEWEB)

    Takeno, S.; Kumagaya, M.; Azuma, T.

    1984-01-01

    Successive reductions in the amount of coke and fuel oil used in cupolas and annealing furnaces are reported. In the cupolas, 2% oxygen enrichment resulted in a 0.9% drop in coke ratio and a 13.3% increase in output of pig iron. Coke ratios of 9.3-9.5% were obtained by tuyere blow-in of inexpensive carbon materials instead of expensive coke, by the use of formed coke, and by employing a dehumidified blast. In the case of the fuel oil-fired annealing furnaces, fuel oil consumption rates were reduced by treating two charges per heat instead of one. Energy consumption was successively reduced by 25-71% by 1) adopting a ceramic fibre heat-insulating material, 2) changing to low-oxygen combustion by increasing the number of burners, 3) lengthening the time during which the furnace high-temperature zone is maintained, 4) raising the combustion chamber load by using ceramic fibres in the furnace casing. 3 references.

  4. A coherent quantum annealer with Rydberg atoms

    Science.gov (United States)

    Glaetzle, A. W.; van Bijnen, R. M. W.; Zoller, P.; Lechner, W.

    2017-06-01

    There is a significant ongoing effort in realizing quantum annealing with different physical platforms. The challenge is to achieve a fully programmable quantum device featuring coherent adiabatic quantum dynamics. Here we show that combining the well-developed quantum simulation toolbox for Rydberg atoms with the recently proposed Lechner-Hauke-Zoller (LHZ) architecture allows one to build a prototype for a coherent adiabatic quantum computer with all-to-all Ising interactions and, therefore, a platform for quantum annealing. In LHZ an infinite-range spin-glass is mapped onto the low energy subspace of a spin-1/2 lattice gauge model with quasi-local four-body parity constraints. This spin model can be emulated in a natural way with Rubidium and Caesium atoms in a bipartite optical lattice involving laser-dressed Rydberg-Rydberg interactions, which are several orders of magnitude larger than the relevant decoherence rates. This makes the exploration of coherent quantum enhanced optimization protocols accessible with state-of-the-art atomic physics experiments.

  5. A coherent quantum annealer with Rydberg atoms.

    Science.gov (United States)

    Glaetzle, A W; van Bijnen, R M W; Zoller, P; Lechner, W

    2017-06-22

    There is a significant ongoing effort in realizing quantum annealing with different physical platforms. The challenge is to achieve a fully programmable quantum device featuring coherent adiabatic quantum dynamics. Here we show that combining the well-developed quantum simulation toolbox for Rydberg atoms with the recently proposed Lechner-Hauke-Zoller (LHZ) architecture allows one to build a prototype for a coherent adiabatic quantum computer with all-to-all Ising interactions and, therefore, a platform for quantum annealing. In LHZ an infinite-range spin-glass is mapped onto the low energy subspace of a spin-1/2 lattice gauge model with quasi-local four-body parity constraints. This spin model can be emulated in a natural way with Rubidium and Caesium atoms in a bipartite optical lattice involving laser-dressed Rydberg-Rydberg interactions, which are several orders of magnitude larger than the relevant decoherence rates. This makes the exploration of coherent quantum enhanced optimization protocols accessible with state-of-the-art atomic physics experiments.

  6. Magnetic field annealing for improved creep resistance

    Energy Technology Data Exchange (ETDEWEB)

    Brady, Michael P.; Ludtka, Gail M.; Ludtka, Gerard M.; Muralidharan, Govindarajan; Nicholson, Don M.; Rios, Orlando; Yamamoto, Yukinori

    2015-12-22

    The method provides heat-resistant chromia- or alumina-forming Fe-, Fe(Ni), Ni(Fe), or Ni-based alloys having improved creep resistance. A precursor is provided containing preselected constituents of a chromia- or alumina-forming Fe-, Fe(Ni), Ni(Fe), or Ni-based alloy, at least one of the constituents for forming a nanoscale precipitate MaXb where M is Cr, Nb, Ti, V, Zr, or Hf, individually and in combination, and X is C, N, O, B, individually and in combination, a=1 to 23 and b=1 to 6. The precursor is annealed at a temperature of 1000-1500.degree. C. for 1-48 h in the presence of a magnetic field of at least 5 Tesla to enhance supersaturation of the M.sub.aX.sub.b constituents in the annealed precursor. This forms nanoscale M.sub.aX.sub.b precipitates for improved creep resistance when the alloy is used at service temperatures of 500-1000.degree. C. Alloys having improved creep resistance are also disclosed.

  7. Annealing effects on deuterium retention behavior in damaged tungsten

    Directory of Open Access Journals (Sweden)

    S. Sakurada

    2016-12-01

    Full Text Available Effects of annealing after/under iron (Fe ion irradiation on deuterium (D retention behavior in tungsten (W were studied. The D2 TDS spectra as a function of heating temperature for 0.1dpa damaged W showed that the D retention was clearly decreased as the annealing temperature was increased. In particular, the desorption of D trapped by voids was largely reduced by annealing at 1173K. The TEM observation indicated that the size of dislocation loops was clearly grown, and its density was decreased by the annealing above 573K. After annealing at 1173K, almost all the dislocation loops were recovered. The results of positron annihilation spectroscopy suggested that the density of vacancy-type defects such as voids, was decreased as the annealing temperature was increased, while its size was increased, indicating that the D retention was reduced by the recovery of the voids. Furthermore, it was found that the desorption temperature of D trapped by the voids for damaged W above 0.3dpa was shifted toward higher temperature side. These results lead to a conclusion that the D retention behavior is controlled by defect density. The D retention in the samples annealed during irradiation was less than that annealed after irradiation. This result shows that defects would be quickly annihilated before stabilization by annealing during irradiation.

  8. Structure and magnetism of Ni/Ti multilayers on annealing

    Indian Academy of Sciences (India)

    Surendra Singh; Saibal Basu; P Bhatt

    2008-11-01

    Neutron reflectometry study has been carried out in unpolarized (NR) and polarized (PNR) mode to understand the structure and magnetic properties of alloy formation at the interfaces of Ni/Ti multilayers on annealing. The PNR data from annealed sample shows a noticeable change with respect to the as-deposited sample. These changes are: a prominent shift of the multilayer Bragg peak to a higher angle and a decrease in the intensity of the Bragg peak. The PNR data from annealed sample revealed the formation of magnetically dead alloy layers at the interfaces. Changes in roughness parameters of the interfaces on annealing were also observed in the PNR data.

  9. A Parallel Genetic Simulated Annealing Hybrid Algorithm for Task Scheduling

    Institute of Scientific and Technical Information of China (English)

    SHU Wanneng; ZHENG Shijue

    2006-01-01

    In this paper combined with the advantages of genetic algorithm and simulated annealing, brings forward a parallel genetic simulated annealing hybrid algorithm (PGSAHA) and applied to solve task scheduling problem in grid computing .It first generates a new group of individuals through genetic operation such as reproduction, crossover, mutation, etc, and than simulated anneals independently all the generated individuals respectively.When the temperature in the process of cooling no longer falls, the result is the optimal solution on the whole.From the analysis and experiment result, it is concluded that this algorithm is superior to genetic algorithm and simulated annealing.

  10. Temperature distribution study in flash-annealed amorphous ribbons

    Energy Technology Data Exchange (ETDEWEB)

    Moron, C. E-mail: cmoron@eui.upm.es; Garcia, A.; Carracedo, M.T

    2003-01-01

    Negative magnetrostrictive amorphous ribbons have been locally current annealed with currents from 1 to 8 A and annealing times from 14 ms to 200 s. In order to obtain information about the sample temperature during flash or current annealing, a study of the temperature dispersion during annealing in amorphous ribbons was made. The local temperature variation was obtained by measuring the local intensity of the infrared emission of the sample with a CCD liquid nitrogen cooled camera. A distribution of local temperature has been found in spite of the small dimension of the sample.

  11. Studies on resistive hysteresis characteristics of metal organic decomposition-derived BaTiO3 thin films prepared under various annealing conditions and related switching endurance properties

    Science.gov (United States)

    Sugie, Toshiyuki; Maejima, So; Yamashita, Kaoru; Noda, Minoru

    2016-10-01

    We have prepared metal organic decomposition (MOD)-derived BaTiO3 (BT) thin films under various annealing conditions, especially in nitrogen, and investigated the properties of bipolar-type resistive switching, focusing on the relation between oxygen vacancies and the behavior of resistive hysteresis. BT thin film with both pre annealing and final annealing in nitrogen (layer-by-layer annealing) showed the resistive hysteresis of bipolar-type switching with current ON/OFF ratios of 2 orders of magnitude for both bias polarities. Moreover, it showed the endurance property with the 104 switching cycles. It is possible that the non-filament bipolar-type resistive switching has origins not only at the metal electrode/oxide interface but also the inside of the oxide films, that is, the presence of the oxygen vacancies inside of BT thin films would play an important role in the bipolar-type resistive switching and in improving the switching endurance properties.

  12. Fuel Cycle Research & Development Technical Monthly - June 2012

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Michael C. [Los Alamos National Laboratory

    2012-07-25

    Topics are: (1) MPACT Campaign - (a) Management and Integration - Coordination meetings between NE and NA-22, NA-24, and NA-82 were conducted the week of June 11th. Preparations are being made for the next MPACT working group meeting, scheduled for Aug 28-30 at Idaho Falls. In addition to covering accomplishments and discussing future plans, a site tour of INL facilities (MFC, EBR, ATR, INTEC) is being organized. (2) Accounting and Control Technologies - (a) Microcalorimetry - Now operating 256-pixel array at LANL. We are in the process of tuning detector parameters to improve and optimize performance. Preliminary measurements show approximate number of live pixels is similar to that observed previously at NIST. Continuing to study contribution to systematic error from uncertainties in tabulated gamma-ray energies. (b) Electrochemical Sensor - Testing of sensors fashioned from different precursor materials continued. SEM analysis of all used sensors has been or will be performed. (c) Lead Slowing Down Spectrometer - Ongoing perturbation calculations are providing information on the fundamental systematic error limits of LSDS. In order to achieve separating the contribution of Pu and 235U to the signal, there will need to be tight controls on systematic errors. Continuing to look into a He4 detector. Research into local construction of a He4 detector continued. We have started to apply the algorithm to test the LSDS using experimental data from previous RPI measurements. PNNL also developed a plan to address the lack of statistics in the MCNP modeling of the NGSI 64 assemblies. The ISU graduate student built and tested a fission chamber to gain experience with them. (d) Fast Neutron Imaging to Quantify Nuclear Materials - The imaging detector design was modified for each pixel to have an 8 x 8 pixel array. Quotations and purchasing process for components, including the new PSD scintillator are in progress. (e) Fast Neutron Multiplicity Analysis - The team submitted two papers to the upcoming INMM meeting that are related to the fast neutron multiplicity R&D effort. Progress was made on the project's main goal of designing a concept for a prototype fast-neutron multiplicity counter. We started laying out the outline for the final report. We have been working with our ORNL collaborators to develop a new digitizer system to support our experimental campaign planned for next year. (3) MPACT Analysis Tools - (a) Multi-isotope Process Monitor - Fuel characterization framework development continued during June. A report describing the methodologies is being completed. Kenneth Dayman, from University of Texas, spent a week at PNNL wrapping up his master's research and working on a journal submission covering that work. The target journal is the IEEE transactions on Nuclear Science; submission is planned for the end of July. A proposal to instrument H-Canyon is being prepared in conjunction with SRNL and the NNSA's NGSI program. The impact of gamma-ray spectrum counting statistics on the precision of relative radioisotope component intensities as reconstructed via Principal Component Regression (PCR) continued in June with Monte Carlo simulations of a two-component (i.e., two radioisotope) system. This work generalizes earlier studies in FY12 in which Poisson counting variations of only a single spectrum component were simulated. (b) Modeling and Simulation for Analysis of Safeguards Performance (Electrochemical) - Preliminary insights into safeguards challenges and the initial design for an electrochemical plant have been written up into an INMM paper and will be presented at the INMM Summer Meeting. Work is currently adding a new visualization capability for integrating materials accountancy with physical protection. (c) Material Control including Process Monitoring (Pattern Recognition, Sensors) - Fabrication of quartz chips continued at an external foundry. Awaiting delivery of the heat exchange manifold and chip holder. (d) MPACT System Integration and Technical Support - The initial report on cost-basis metrics for nuclear material security risk and proliferation risk was completed as scheduled. (4) Safeguards and Security by Design - (a) Used fuels storage security analysis, guidance and best practices - RFP was finalized and sent out. Awaiting response from World Institute for Nuclear Security. Coordinated with Scott Demuth on joint report - LANL milestone on best practices. Attended Nuclear Energy Institute National Nuclear Security Conference. Developed plan for soliciting input on prioritized issues for used fuel storage security. Worked on setting up a meeting with the Nuclear Regulatory Commission. Worked on FY2013 work package planning.

  13. Synthesis of copper nanoparticles in a fluoropolymer matrix by annealing in vacuum

    Energy Technology Data Exchange (ETDEWEB)

    Safonov, Alexey, E-mail: safonov@itp.nsc.ru [Kutateladze Institute of Thermophysics SB RAS, Lavrentyev Ave. 1, 630090, Novosibirsk (Russian Federation); Sulyaeva, Veronica [Nikolaev Institute of Inorganic Chemistry SB RAS, Lavrentyev Ave. 3, 630090, Novosibirsk (Russian Federation); Timoshenko, Nikolay; Starinskiy, Sergey [Kutateladze Institute of Thermophysics SB RAS, Lavrentyev Ave. 1, 630090, Novosibirsk (Russian Federation)

    2017-07-12

    In this paper, a method for synthesizing copper nanoparticles in a fluoropolymer matrix is proposed which prevents the reduction in the plasmonic properties due to the oxidation of the metal. The basic idea of the proposed method of nanoparticle synthesis is to anneal of thin metal film coated with a thin layer of fluoropolymer. The morphology and optical properties of the resulting composites were determined. The optical properties remained unchanged after several months of storage under standard conditions. - Highlights: • The copper-fluoropolymer composites are obtained by a combination of GJD and HWCVD. • The annealing of thin Cu film covered with fluoropolymer leads to formation of NPs. • The dilution of the localized surface plasmon resonance due to oxidation was analyzed. • The plasmonic properties of the Cu NPs are saved in the fluoropolymer matrix. • The fluoropolymer matrix prevents oxidation of metal NPs.

  14. Heart murmur detection based on wavelet transformation and a synergy between artificial neural network and modified neighbor annealing methods.

    Science.gov (United States)

    Eslamizadeh, Gholamhossein; Barati, Ramin

    2017-05-01

    Early recognition of heart disease plays a vital role in saving lives. Heart murmurs are one of the common heart problems. In this study, Artificial Neural Network (ANN) is trained with Modified Neighbor Annealing (MNA) to classify heart cycles into normal and murmur classes. Heart cycles are separated from heart sounds using wavelet transformer. The network inputs are features extracted from individual heart cycles, and two classification outputs. Classification accuracy of the proposed model is compared with five multilayer perceptron trained with Levenberg-Marquardt, Extreme-learning-machine, back-propagation, simulated-annealing, and neighbor-annealing algorithms. It is also compared with a Self-Organizing Map (SOM) ANN. The proposed model is trained and tested using real heart sounds available in the Pascal database to show the applicability of the proposed scheme. Also, a device to record real heart sounds has been developed and used for comparison purposes too. Based on the results of this study, MNA can be used to produce considerable results as a heart cycle classifier. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. In Situ Monitoring of the Thermal-Annealing Effect in a Monolayer of MoS2

    Science.gov (United States)

    Su, Liqin; Yu, Yifei; Cao, Linyou; Zhang, Yong

    2017-03-01

    We perform in situ two-cycle thermal-annealing studies for a transferred CVD-grown monolayer MoS2 on a SiO2/Si substrate, using spatially resolved micro-Raman and photoluminescence spectroscopy. The evolution in film morphology and film-substrate bonding is continuously monitored by Raman spectroscopy. After the thermal cycling and being annealed at 305 °C twice, the film morphology and film-substrate bonding are significantly modified, which together with the removal of polymer residues causes major changes in the strain and doping distribution over the film, and thus the optical properties. Before annealing, the strain associated with ripples in the transferred film dominates the spatial distributions of the photoluminescence peak position and intensity over the film; after annealing, the variation in film-substrate bonding, affecting both strain and doping, becomes the leading factor. This work reveals that the film-substrate bonding, and thus the strain and doping, is nonstationary under thermal stress, which is important for understanding the substrate effects on the optical and transport properties of the 2D material and their impact on device applications.

  16. Monthly energy review

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    This document presents an overview of the Energy Information Administration`s (EIA) recent monthly energy statistics. The statistics cover the major activities of U.S. production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors.

  17. Photos of the month

    CERN Multimedia

    Claudia Marcelloni de Oliveira

    Congratulations to Adele Rimoldi, ATLAS physicist from Pavia, who ran her first marathon in New York last month. Adele completed the 42.2 km in a time of 4:49:19. She sure makes it look easy!!! The ATLAS pixel service quarter panel in SR1

  18. Monthly Energy Review

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-28

    This publication presents an overview of the Energy information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. Two brief ``energy plugs`` (reviews of EIA publications) are included, as well.

  19. FES cycling.

    Science.gov (United States)

    Newham, D J; Donaldson, N de N

    2007-01-01

    Spinal cord injury (SCI) leads to a partial or complete disruption of motor, sensory, and autonomic nerve pathways below the level of the lesion. In paraplegic patients, functional electrical stimulation (FES) was originally widely considered as a means to restore walking function but this was proved technically very difficult because of the numerous degrees of freedom involved in walking. FES cycling was developed for people with SCI and has the advantages that cycling can be maintained for reasonably long periods in trained muscles and the risk of falls is low. In the article, we review research findings relevant to the successful application of FES cycling including the effects on muscle size, strength and function, and the cardiovascular and bone changes. We also describe important practical considerations in FES cycling regarding the application of surface electrodes, training and setting up the stimulator limitations, implanted stimulators and FES cycling including FES cycling in groups and other FES exercises such as FES rowing.

  20. Hierarchical Network Design Using Simulated Annealing

    DEFF Research Database (Denmark)

    Thomadsen, Tommy; Clausen, Jens

    2002-01-01

    The hierarchical network problem is the problem of finding the least cost network, with nodes divided into groups, edges connecting nodes in each groups and groups ordered in a hierarchy. The idea of hierarchical networks comes from telecommunication networks where hierarchies exist. Hierarchical...... networks are described and a mathematical model is proposed for a two level version of the hierarchical network problem. The problem is to determine which edges should connect nodes, and how demand is routed in the network. The problem is solved heuristically using simulated annealing which as a sub......-algorithm uses a construction algorithm to determine edges and route the demand. Performance for different versions of the algorithm are reported in terms of runtime and quality of the solutions. The algorithm is able to find solutions of reasonable quality in approximately 1 hour for networks with 100 nodes....

  1. Thermoelectric properties by high temperature annealing

    Science.gov (United States)

    Ren, Zhifeng (Inventor); Chen, Gang (Inventor); Kumar, Shankar (Inventor); Lee, Hohyun (Inventor)

    2009-01-01

    The present invention generally provides methods of improving thermoelectric properties of alloys by subjecting them to one or more high temperature annealing steps, performed at temperatures at which the alloys exhibit a mixed solid/liquid phase, followed by cooling steps. For example, in one aspect, such a method of the invention can include subjecting an alloy sample to a temperature that is sufficiently elevated to cause partial melting of at least some of the grains. The sample can then be cooled so as to solidify the melted grain portions such that each solidified grain portion exhibits an average chemical composition, characterized by a relative concentration of elements forming the alloy, that is different than that of the remainder of the grain.

  2. Coupled Quantum Fluctuations and Quantum Annealing

    Science.gov (United States)

    Hormozi, Layla; Kerman, Jamie

    We study the relative effectiveness of coupled quantum fluctuations, compared to single spin fluctuations, in the performance of quantum annealing. We focus on problem Hamiltonians resembling the the Sherrington-Kirkpatrick model of Ising spin glass and compare the effectiveness of different types of fluctuations by numerically calculating the relative success probabilities and residual energies in fully-connected spin systems. We find that for a small class of instances coupled fluctuations can provide improvement over single spin fluctuations and analyze the properties of the corresponding class. Disclaimer: This research was funded by ODNI, IARPA via MIT Lincoln Laboratory under Air Force Contract No. FA8721-05-C-0002. The views and conclusions contained herein are those of the authors and should not be interpreted as necessarily representing the official policies or endorsements, either expressed or implied, of ODNI, IARPA, or the US Government.

  3. Rapid thermal anneal of arsenic implanted silicon

    Energy Technology Data Exchange (ETDEWEB)

    Feygenson, A.

    1985-01-01

    The distribution of arsenic implanted into silicon during rapid thermal anneal (RTA) was investigated. Secondary ion mass spectrometry, Rutherford backscattering spectrometry, and channeling techniques were used for the measurement of the total (chemical) dopant profile. The electrically active dopant profiles were measured with sheet resistance, sheet-resistance maps, spreading resistance and pinch resistors. It was found that arsenic profile after RTA is influenced by many parameters including crystallographic orientation of the sample, temperature gradient, and defect structure in the surface part affected by heavy arsenic implant. A diffusion model based on inhomogeneous medium was examined. Exact solutions of the diffusion equation were obtained for the rectangular and Gaussian initial dopant profiles. Calculated results are compared to the measured profiles. It is concluded that model satisfactory predicts the major features of the arsenic diffusion into silicon during RTA.

  4. Rapid Thermal Anneal of Arsenic Implanted Silicon.

    Science.gov (United States)

    Feygenson, Anatoly

    1985-12-01

    The distribution of arsenic implanted into silicon during rapid thermal anneal (RTA) has been investigated. Secondary ion mass spectrometry (SIMS), Rutherford backscattering spectrometry (RBS) and channeling techniques were used for the measurement of the total (chemical) dopant profile. The electrically active dopant profiles were measured with sheet resistance, sheet resistance maps, spreading resistance, and pinch resistors. It has been found that arsenic profile after RTA is influenced by many parameters including crystallographic orientation of the sample, temperature gradient, and defect structure in the surface part affected by heavy arsenic implant. A diffusion model based on inhomogeneous medium was examined. Exact solutions of the diffusion equation were obtained for the rectangular and Gaussian initial dopant profiles. Calculated results are compared to the measured profiles. It is concluded that model satisfactory predicts the major features of the arsenic diffusion into silicon during RTA.

  5. Influence of phosphate esters on the annealing properties of starch

    DEFF Research Database (Denmark)

    Wischmann, Bente; Muhrbeck, Per

    1998-01-01

    The effects of annealing on native potato, waxy maize, and phosphorylated waxy maize starches were compared. Phosphorylated waxy maize starch responded to annealing in a manner between that of the naturally phosphorylated potato starch and that of the native waxy maize starch. The gelatinisation ...

  6. Annealing Behavior of Si1-xGex/Si Heterostructures

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The behavior of Si1-xGex/Si heterostructures under different annealing conditions has been studied. It is found that while RTA treatment diminishes the point defects, it introduces the misfit dislocations into Si1-xGex layers at same time. Higher annealing temperature will result in the propagation of misfit dislocations and then the total destruction of the crystal quality.

  7. Parameters Optimization of Low Carbon Low Alloy Steel Annealing Process

    Institute of Scientific and Technical Information of China (English)

    Maoyu ZHAO; Qianwang CHEN

    2013-01-01

    A suitable match of annealing process parameters is critical for obtaining the fine microstructure of material.Low carbon low alloy steel (20CrMnTi) was heated for various durations near Ac temperature to obtain fine pearlite and ferrite grains.Annealing temperature and time were used as independent variables,and material property data were acquired by orthogonal experiment design under intercritical process followed by subcritical annealing process (IPSAP).The weights of plasticity (hardness,yield strength,section shrinkage and elongation) of annealed material were calculated by analytic hierarchy process,and then the process parameters were optimized by the grey theory system.The results observed by SEM images show that microstructure of optimization annealing material are consisted of smaller lamellar pearlites (ferrite-cementite)and refining ferrites which distribute uniformly.Morphologies on tension fracture surface of optimized annealing material indicate that the numbers of dimple fracture show more finer toughness obviously comparing with other annealing materials.Moreover,the yield strength value of optimization annealing material decreases apparently by tensile test.Thus,the new optimized strategy is accurate and feasible.

  8. Remote sensing of atmospheric duct parameters using simulated annealing

    Institute of Scientific and Technical Information of China (English)

    Zhao Xiao-Feng; Huang Si-Xun; Xiang Jie; Shi Wei-Lai

    2011-01-01

    Simulated annealing is one of the robust optimization schemes. Simulated annealing mimics the annealing process of the slow cooling of a heated metal to reach a stable minimum energy state. In this paper,we adopt simulated annealing to study the problem of the remote sensing of atmospheric duct parameters for two different geometries of propagation measurement. One is from a single emitter to an array of radio receivers (vertical measurements),and the other is from the radar clutter returns (horizontal measurements). Basic principles of simulated annealing and its applications to refractivity estimation are introduced. The performance of this method is validated using numerical experiments and field measurements collected at the East China Sea. The retrieved results demonstrate the feasibility of simulated annealing for near real-time atmospheric refractivity estimation. For comparison,the retrievals of the genetic algorithm are also presented. The comparisons indicate that the convergence speed of simulated annealing is faster than that of the genetic algorithm,while the anti-noise ability of the genetic algorithm is better than that of simulated annealing.

  9. Effect of recrystallization annealing on the inelastic properties of TiNi alloy under bending

    Science.gov (United States)

    Grishkov, V. N.; Lotkov, A. I.; Baturin, A. A.; Cherniavsky, A. G.; Timkin, V. N.; Zhapova, D. Yu.

    2016-11-01

    The data reported here show that recrystallization annealing at 973 K transforms the initial nanocrystalline structure of Ti49.1Ni50.9 (at %) into a microcrystalline structure with an average grain size of ≤11.4 µm and changes the sequence of martensite transformations from B2→R→B19' to B2→B19'. Also dependences of the superelasticity effect (SE), shape memory effect (SME), summary reversible inelastic strain (SIS = SE + SME), and plastic strain on total strain for the alloy exposed to bending in isothermal (295 K) loading-unloading cycles with post-unloading heating are presented.

  10. Your Child's Development: 9 Months

    Science.gov (United States)

    ... For Parents MORE ON THIS TOPIC Your Baby's Growth: 9 Months Your Baby's Hearing, Vision, and Other Senses: 9 Months Your Child's Checkup: 9 Months Medical Care and Your 8- to 12-Month-Old Feeding Your 8- to 12-Month-Old Sleep and Your 8- to 12-Month-Old Contact ...

  11. Mechanism of Annealing Softening of Rolled or Forged Tool Steel

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    In order to reduce hardness of rolled or forged steels after annealing and improve processability, the diameter and dispersity of carbides were measured by SEM and quantitative metallography. The microstructure of annealed steel was analyzed by TEM. The effects of the factors such as solute atoms, carbides, grain boundary and interphase boundary were studied. The mechanism of annealing softening of steels was analyzed on the examples of steels H13, S5, S7, X45CrNiMo4, which are treated with new technology. The results showed that the softening of H13, S7, S5 is easier obtained by isothermal or slow cooling annealing from slightly below A1, but hardness of X45CrNiMo4 after annealing is reduced effectively by obtaining coarse lamellar pearlite. Economic results can be obtained from good processability.

  12. Quantum annealing with all-to-all connected nonlinear oscillators

    DEFF Research Database (Denmark)

    Puri, Shruti; Andersen, Christian Kraglund; Grimsmo, Arne L.

    2017-01-01

    Quantum annealing aims at solving combinatorial optimization problems mapped to Ising interactions between quantum spins. Here, with the objective of developing a noise-resilient annealer, we propose a paradigm for quantum annealing with a scalable network of two-photon-driven Kerr......-nonlinear resonators. Each resonator encodes an Ising spin in a robust degenerate subspace formed by two coherent states of opposite phases. A fully connected optimization problem is mapped to local fields driving the resonators, which are connected with only local four-body interactions. We describe an adiabatic...... annealing protocol in this system and analyse its performance in the presence of photon loss. Numerical simulations indicate substantial resilience to this noise channel, leading to a high success probability for quantum annealing. Finally, we propose a realistic circuit QED implementation of this promising...

  13. Annealing of ion-implanted GaN

    CERN Document Server

    Burchard, A; Stötzler, A; Weissenborn, R; Deicher, M

    1999-01-01

    $^{111m}$Cd and $^{112}$Cd ions have been implanted into GaN. With photoluminescence spectroscopy and perturbed $\\gamma-\\gamma$-angular correlation spectroscopy (PAC) the reduction of implantation damage and the optical activation of the implants have been observed as a function of annealing temperature using different annealing methods. The use of N$_{2}$ or NH$_{3}$ atmosphere during annealing allows temperatures up to 1323k and 1373 K, respectively, but above 1200 K a strong loss of Cd from the GaN has been observed. Annealing GaN together with elementary Al forms a protective layer on the GaN surface allowing annealing temperatures up to 1570 K for 10 min. (11 refs).

  14. Influence of time of annealing on anneal hardening effect of a cast CuZn alloy

    OpenAIRE

    Nestorović Svetlana; Ivanić Lj.; Marković Desimir

    2003-01-01

    Investigated cast copper alloy containing 8at%Zn of a solute. For comparison parallel specimens made from cast pure copper. Copper and copper alloy were subjected to cold rolling with different a final reduction of 30,50 and 70%. The cold rolled copper and copper alloy samples were isochronally and isothermally annealed up to recrystallization temperature. After that the values of hardness, strength and electrical conductivity were measured and X-ray analysis was performed. These investigatio...

  15. Petroleum marketing monthly

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-07-01

    Petroleum Marketing Monthly (PPM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o. b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

  16. Petroleum marketing monthly

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

  17. Electric power monthly

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-08-01

    The Energy Information Administration (EIA) prepares the Electric Power Monthly (EPM) for a wide audience including Congress, Federal and State agencies, the electric utility industry, and the general public. This publication provides monthly statistics for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North American Electric Reliability Council (NERC) regions. The EIA publishes statistics in the EPM on net generation by energy source, consumption, stocks, quantity, quality, and cost of fossil fuels; and capability of new generating units by company and plant. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead.

  18. Electric power monthly

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Sandra R.; Johnson, Melvin; McClevey, Kenneth; Calopedis, Stephen; Bolden, Deborah

    1992-05-01

    The Electric Power Monthly is prepared by the Survey Management Division; Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), Department of Energy. This publication provides monthly statistics at the national, Census division, and State levels for net generation, fuel consumption, fuel stocks, quantity and quality of fuel, cost of fuel, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fuel are also displayed for the North American Electric Reliability Council (NERC) regions. Additionally, statistics by company and plant are published in the EPM on capability of new plants, new generation, fuel consumption, fuel stocks, quantity and quality of fuel, and cost of fuel.

  19. Structural Evaluation and Mechanical Properties of Aluminum/Tungsten Carbide Composites Fabricated by Continual Annealing and Press Bonding (CAPB) Process

    Science.gov (United States)

    Amirkhanlou, Sajjad; Ketabchi, Mostafa; Parvin, Nader; Drummen, G. P. C.

    2014-12-01

    In the present work, a novel technique is introduced called continual annealing and press bonding (CAPB) for the manufacturing of a bulk aluminum matrix composite dispersed with 10 vol pct tungsten carbide particles (Al/WCp composite). The microstructural evolution and mechanical properties of the Al/WCp composite during various CAPB cycles were examined by scanning electron microscopy (SEM), wavelength dispersive X-ray spectroscopy (WDX), and tensile testing. The microstructure of the fabricated composite after fourteen cycles of CAPB showed homogenous distribution of the WC particles in the aluminum matrix and strong bonding between the various layers. According to WDX analysis, the manufactured Al/WCp composite did not evidence the presence of additional elements. The results indicated that the tensile strength of the composites increased with the number of CAPB cycles, and reached a maximum value of 140 MPa at the end of the fourteenth cycle, which was 1.6 times higher than the obtained value for annealed aluminum (raw material, 88 MPa). Even though the elongation of the Al/WCp composite was reduced during the initial cycles of CAPB process, it increased significantly during the final cycles. SEM observation of fracture surfaces showed that the rupture mode in the CAPB-processed Al/WCp composite was of the shear ductile rupture type.

  20. Annealing of (DU-10Mo)-Zr Co-Rolled Foils

    Energy Technology Data Exchange (ETDEWEB)

    Pacheco, Robin Montoya [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Alexander, David John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Mccabe, Rodney James [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Clarke, Kester Diederik [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Scott, Jeffrey E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Montalvo, Joel Dwayne [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Papin, Pallas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ansell, George S. [Colorado School of Mines, Golden, CO (United States)

    2017-01-20

    Producing uranium-10wt% molybdenum (DU-10Mo) foils to clad with Al first requires initial bonding of the DU-10Mo foil to zirconium (Zr) by hot rolling, followed by cold rolling to final thickness. Rolling often produces wavy (DU-10Mo)-Zr foils that should be flattened before further processing, as any distortions could affect the final alignment and bonding of the Al cladding to the Zr co-rolled surface layer; this bonding is achieved by a hot isostatic pressing (HIP) process. Distortions in the (DU-10Mo)-Zr foil may cause the fuel foil to press against the Al cladding and thus create thinner or thicker areas in the Al cladding layer during the HIP cycle. Post machining is difficult and risky at this stage in the process since there is a chance of hitting the DU-10Mo. Therefore, it is very important to establish a process to flatten and remove any waviness. This study was conducted to determine if a simple annealing treatment could flatten wavy foils. Using the same starting material (i.e. DU-10Mo coupons of the same thickness), five different levels of hot rolling and cold rolling, combined with five different annealing treatments, were performed to determine the effect of these processing variables on flatness, bonding of layers, annealing response, microstructure, and hardness. The same final thickness was reached in all cases. Micrographs, textures, and hardness measurements were obtained for the various processing combinations. Based on these results, it was concluded that annealing at 650°C or higher is an effective treatment to appreciably reduce foil waviness.

  1. Petroleum marketing monthly

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data.

  2. Annealed Scaling for a Charged Polymer

    Science.gov (United States)

    Caravenna, F.; den Hollander, F.; Pétrélis, N.; Poisat, J.

    2016-03-01

    This paper studies an undirected polymer chain living on the one-dimensional integer lattice and carrying i.i.d. random charges. Each self-intersection of the polymer chain contributes to the interaction Hamiltonian an energy that is equal to the product of the charges of the two monomers that meet. The joint probability distribution for the polymer chain and the charges is given by the Gibbs distribution associated with the interaction Hamiltonian. The focus is on the annealed free energy per monomer in the limit as the length of the polymer chain tends to infinity. We derive a spectral representation for the free energy and use this to prove that there is a critical curve in the parameter plane of charge bias versus inverse temperature separating a ballistic phase from a subballistic phase. We show that the phase transition is first order. We prove large deviation principles for the laws of the empirical speed and the empirical charge, and derive a spectral representation for the associated rate functions. Interestingly, in both phases both rate functions exhibit flat pieces, which correspond to an inhomogeneous strategy for the polymer to realise a large deviation. The large deviation principles in turn lead to laws of large numbers and central limit theorems. We identify the scaling behaviour of the critical curve for small and for large charge bias. In addition, we identify the scaling behaviour of the free energy for small charge bias and small inverse temperature. Both are linked to an associated Sturm-Liouville eigenvalue problem. A key tool in our analysis is the Ray-Knight formula for the local times of the one-dimensional simple random walk. This formula is exploited to derive a closed form expression for the generating function of the annealed partition function, and for several related quantities. This expression in turn serves as the starting point for the derivation of the spectral representation for the free energy, and for the scaling theorems

  3. Annealed Scaling for a Charged Polymer

    Energy Technology Data Exchange (ETDEWEB)

    Caravenna, F., E-mail: francesco.caravenna@unimib.it [Università degli Studi di Milano-Bicocca, Dipartimento di Matematica e Applicazioni (Italy); Hollander, F. den, E-mail: denholla@math.leidenuniv.nl [Leiden University, Mathematical Institute (Netherlands); Pétrélis, N., E-mail: nicolas.petrelis@univ-nantes.fr [Université de Nantes, Laboratoire de Mathématiques Jean Leray UMR 6629 (France); Poisat, J., E-mail: poisat@ceremade.dauphine.fr [Université Paris-Dauphine, PSL Research University, CEREMADE, UMR 7534 (France)

    2016-03-15

    This paper studies an undirected polymer chain living on the one-dimensional integer lattice and carrying i.i.d. random charges. Each self-intersection of the polymer chain contributes to the interaction Hamiltonian an energy that is equal to the product of the charges of the two monomers that meet. The joint probability distribution for the polymer chain and the charges is given by the Gibbs distribution associated with the interaction Hamiltonian. The focus is on the annealed free energy per monomer in the limit as the length of the polymer chain tends to infinity. We derive a spectral representation for the free energy and use this to prove that there is a critical curve in the parameter plane of charge bias versus inverse temperature separating a ballistic phase from a subballistic phase. We show that the phase transition is first order. We prove large deviation principles for the laws of the empirical speed and the empirical charge, and derive a spectral representation for the associated rate functions. Interestingly, in both phases both rate functions exhibit flat pieces, which correspond to an inhomogeneous strategy for the polymer to realise a large deviation. The large deviation principles in turn lead to laws of large numbers and central limit theorems. We identify the scaling behaviour of the critical curve for small and for large charge bias. In addition, we identify the scaling behaviour of the free energy for small charge bias and small inverse temperature. Both are linked to an associated Sturm-Liouville eigenvalue problem. A key tool in our analysis is the Ray-Knight formula for the local times of the one-dimensional simple random walk. This formula is exploited to derive a closed form expression for the generating function of the annealed partition function, and for several related quantities. This expression in turn serves as the starting point for the derivation of the spectral representation for the free energy, and for the scaling theorems

  4. Surface Morphology of Annealed Lead Phthalocyanine Thin Films

    Directory of Open Access Journals (Sweden)

    P.Kalugasalam,

    2010-06-01

    Full Text Available The thin films of Lead Phthalocyanine (PbPc on glass substrates were prepared by Vacuum deposition. The thickness of the films was 450 nm. The sample annealed in high vacuum at 373 K temperature. The sample has been analysed by X-ray diffraction, scanning electron microscopy and atomic force microscopy in order to get structural and surface morphology of the PbPc thin film. The formation of XRD patterns of PbPc shows a triclinic grains (T seen along with monoclinic (M forms of PbPc. The sample is annealed at 373 K temperatures; the film shows peaks that assigned to the triclinic phase. SEM and AFM are the best tools to investigate the surface smoothness and to find the grain size of the particles. The grain size is calculated for all films of different thicknesses. The annealed AFM micrograph shows that the surface of the films consists of large holes. The annealed AFM image indicates a smooth surface. It is very clear that the grain size decreases with increase in the annealing temperature. The roughness also decreases with the increase in film annealing temperature. Annealed film leads to the oxidation of the hthalocyanine with oxygen absorbed or diffused. Therefore, the heat is responsible for the increase in film thickness. Since the films expand, it is believed that the porosity is increased.

  5. The changes of ADI structure during high temperature annealing

    Directory of Open Access Journals (Sweden)

    A. Krzyńska

    2010-01-01

    Full Text Available The results of structure investigations of ADI during it was annealing at elevated temperature are presented. Ductile iron austempered at temperature 325oC was then isothermally annealed 360 minutes at temperature 400, 450, 500 and 550oC. The structure investigations showed that annealing at these temperatures caused substantial structure changes and thus essential hardness decrease, which is most useful property of ADI from point of view its practical application. Degradation advance of the structure depends mainly on annealing temperature, less on the time of the heat treatment. It was concluded that high temperature annealing caused precipitation of Fe3C type carbides, which morphology and distribution depend on temperature. In case of 400oC annealing the carbides precipitates inside bainitic ferrite lath in specific crystallographic planes and partly at the grain boundaries. The annealing at the temperature 550oC caused disappearing of characteristic for ADI needle or lath – like morphology, which is replaced with equiaxed grains. In this case Fe3C carbides take the form very fine precipitates with spheroidal geometry.

  6. Grain coarsening mechanism of Cu thin films by rapid annealing

    Energy Technology Data Exchange (ETDEWEB)

    Sasajima, Yasushi, E-mail: sasajima@mx.ibaraki.ac.jp; Kageyama, Junpei; Khoo, Khyoupin; Onuki, Jin

    2010-09-30

    Cu thin films have been produced by an electroplating method using nominal 9N anode and nominal 6N CuSO{sub 4}.5H{sub 2}O electrolyte. Film samples were heat-treated by two procedures: conventional isothermal annealing in hydrogen atmosphere (abbreviated as H{sub 2} annealing) and rapid thermal annealing with an infrared lamp (abbreviated as RTA). After heat treatment, the average grain diameters and the grain orientation distributions were examined by electron backscattering pattern analysis. The RTA samples (400 {sup o}C for 5 min) have a larger average grain diameter, more uniform grain distribution and higher ratio of (111) orientation than H{sub 2} annealed samples (400 {sup o}C for 30 min). This means that RTA can produce films with coarser and more uniformly distributed grains than H{sub 2} annealing within a short time, i.e. only a few minutes. To clarify the grain coarsening mechanism, grain growth by RTA was simulated using the phase field method. The simulated grain diameter reaches its maximum at a heating rate which is the same order as that in the actual RTA experiment. The maximum grain diameter is larger than that obtained by H{sub 2} annealing with the same annealing time at the isothermal stage as in RTA. The distribution of the misorientation was analyzed which led to a proposed grain growth model for the RTA method.

  7. Embrittlement recovery due to annealing of reactor pressure vessel steels

    Energy Technology Data Exchange (ETDEWEB)

    Eason, E.D.; Wright, J.E.; Nelson, E.E. [Modeling and Computing Services, Boulder, CO (United States); Odette, G.R.; Mader, E.V. [Univ. of California, Santa Barbara, CA (United States)

    1996-03-01

    Embrittlement of reactor pressure vessels (RPVs) can be reduced by thermal annealing at temperatures higher than the normal operating conditions. Although such an annealing process has not been applied to any commercial plants in the United States, one US Army reactor, the BR3 plant in Belgium, and several plants in eastern Europe have been successfully annealed. All available Charpy annealing data were collected and analyzed in this project to develop quantitative models for estimating the recovery in 30 ft-lb (41 J) Charpy transition temperature and Charpy upper shelf energy over a range of potential annealing conditions. Pattern recognition, transformation analysis, residual studies, and the current understanding of the mechanisms involved in the annealing process were used to guide the selection of the most sensitive variables and correlating parameters and to determine the optimal functional forms for fitting the data. The resulting models were fitted by nonlinear least squares. The use of advanced tools, the larger data base now available, and insight from surrogate hardness data produced improved models for quantitative evaluation of the effects of annealing. The quality of models fitted in this project was evaluated by considering both the Charpy annealing data used for fitting and the surrogate hardness data base. The standard errors of the resulting recovery models relative to calibration data are comparable to the uncertainty in unirradiated Charpy data. This work also demonstrates that microhardness recovery is a good surrogate for transition temperature shift recovery and that there is a high level of consistency between the observed annealing trends and fundamental models of embrittlement and recovery processes.

  8. Analysis of radiation-damaged and annealed gallium arsenide and indium phosphide solar cells using deep-level transient spectroscopy techniques. Master's thesis

    Energy Technology Data Exchange (ETDEWEB)

    Pinzon, D.

    1991-03-01

    Degradation of solar cell performance from radiation damage was found to be reversed through annealing processes. The mechanisms behind the degradation and recovery is based on deep-level traps, or defects, in the lattice structure of the solar cell. Through a process known as Deep Level Transient Spectroscopy (DLTS), a correlation can be made between damage/recovery and trap energy level/concentration of the cell. Gallium Arsenide (GaAs) and Indium Phosphide (InP) solar cells were subjected to 1 MeV electron irradiation by a Dynamitron linear acceleration at two fluence levels of 1E1r and 1E15 electrons/cm sq. The process of annealing included thermal annealing at 90 c with forward bias current and thermal annealing alone for (GaAs). After each cycle, DLTS measurements were taken to determine the energy level of the traps and their concentration. Multiple cycles of irradiation, annealing and DLTS were performed to observe the correlation between degradation and recovery to trap energy level and concentration. The results show that the lower energy level traps are associated with the recovery of the cells while the higher level traps are associated with the overall permanent degradation of the cells.

  9. Composition dependent thermal annealing behaviour of ion tracks in apatite

    Energy Technology Data Exchange (ETDEWEB)

    Nadzri, A., E-mail: allina.nadzri@anu.edu.au [Department of Electronic Materials Engineering, Research School of Physics and Engineering, Australian National University, Canberra, ACT 2601 (Australia); Schauries, D.; Mota-Santiago, P.; Muradoglu, S. [Department of Electronic Materials Engineering, Research School of Physics and Engineering, Australian National University, Canberra, ACT 2601 (Australia); Trautmann, C. [GSI Helmholtz Centre for Heavy Ion Research, Planckstrasse 1, 64291 Darmstadt (Germany); Technische Universität Darmstadt, 64287 Darmstadt (Germany); Gleadow, A.J.W. [School of Earth Science, University of Melbourne, Melbourne, VIC 3010 (Australia); Hawley, A. [Australian Synchrotron, 800 Blackburn Road, Clayton, VIC 3168 (Australia); Kluth, P. [Department of Electronic Materials Engineering, Research School of Physics and Engineering, Australian National University, Canberra, ACT 2601 (Australia)

    2016-07-15

    Natural apatite samples with different F/Cl content from a variety of geological locations (Durango, Mexico; Mud Tank, Australia; and Snarum, Norway) were irradiated with swift heavy ions to simulate fission tracks. The annealing kinetics of the resulting ion tracks was investigated using synchrotron-based small-angle X-ray scattering (SAXS) combined with ex situ annealing. The activation energies for track recrystallization were extracted and consistent with previous studies using track-etching, tracks in the chlorine-rich Snarum apatite are more resistant to annealing than in the other compositions.

  10. Excimer laser annealing for low-voltage power MOSFET

    Science.gov (United States)

    Chen, Yi; Okada, Tatsuya; Noguchi, Takashi; Mazzamuto, Fulvio; Huet, Karim

    2016-08-01

    Excimer laser annealing of lumped beam was performed to form the P-base junction for high-performance low-voltage-power MOSFET. An equivalent shallow-junction structure for the P-base junction with a uniform impurity distribution is realized by adopting excimer laser annealing (ELA). The impurity distribution in the P-base junction can be controlled precisely by the irradiated pulse energy density and the number of shots of excimer laser. High impurity activation for the shallow junction has been confirmed in the melted phase. The application of the laser annealing technology in the fabrication process of a practical low-voltage trench gate MOSFET was also examined.

  11. A NEW GENETIC SIMULATED ANNEALING ALGORITHM FOR FLOOD ROUTING MODEL

    Institute of Scientific and Technical Information of China (English)

    KANG Ling; WANG Cheng; JIANG Tie-bing

    2004-01-01

    In this paper, a new approach, the Genetic Simulated Annealing (GSA), was proposed for optimizing the parameters in the Muskingum routing model. By integrating the simulated annealing method into the genetic algorithm, the hybrid method could avoid some troubles of traditional methods, such as arduous trial-and-error procedure, premature convergence in genetic algorithm and search blindness in simulated annealing. The principle and implementing procedure of this algorithm were described. Numerical experiments show that the GSA can adjust the optimization population, prevent premature convergence and seek the global optimal result.Applications to the Nanyunhe River and Qingjiang River show that the proposed approach is of higher forecast accuracy and practicability.

  12. Kriging-approximation simulated annealing algorithm for groundwater modeling

    Science.gov (United States)

    Shen, C. H.

    2015-12-01

    Optimization algorithms are often applied to search best parameters for complex groundwater models. Running the complex groundwater models to evaluate objective function might be time-consuming. This research proposes a Kriging-approximation simulated annealing algorithm. Kriging is a spatial statistics method used to interpolate unknown variables based on surrounding given data. In the algorithm, Kriging method is used to estimate complicate objective function and is incorporated with simulated annealing. The contribution of the Kriging-approximation simulated annealing algorithm is to reduce calculation time and increase efficiency.

  13. Kinetics of the austenite formation during intercritical annealing

    OpenAIRE

    J. Lis; A. Lis

    2008-01-01

    Purpose: of this paper is the effect of the microstructure of the 6Mn16 steel after soft annealing on the kinetics of the austenite formation during next intercritical annealing.Design/methodology/approach: Analytical TEM point analysis with EDAX system attached to Philips CM20 was used to evaluate the concentration of Mn in the microstructure constituents of the multiphase steel,Findings: The increase in soft annealing time from 1-60 hours at 625 °C increases Mn partitioning between ferrite ...

  14. Exploring first-order phase transitions with population annealing

    Science.gov (United States)

    Barash, Lev Yu.; Weigel, Martin; Shchur, Lev N.; Janke, Wolfhard

    2017-03-01

    Population annealing is a hybrid of sequential and Markov chain Monte Carlo methods geared towards the efficient parallel simulation of systems with complex free-energy landscapes. Systems with first-order phase transitions are among the problems in computational physics that are difficult to tackle with standard methods such as local-update simulations in the canonical ensemble, for example with the Metropolis algorithm. It is hence interesting to see whether such transitions can be more easily studied using population annealing. We report here our preliminary observations from population annealing runs for the two-dimensional Potts model with q > 4, where it undergoes a first-order transition.

  15. Commissioners' Monthly Case Activity Report

    Data.gov (United States)

    Occupational Safety and Health Review Commission — Total cases pending at the beginning of the month, total cases added to the docket during the month, total cases disposed of during the month, and total cases...

  16. Benchmarking monthly homogenization algorithms

    Directory of Open Access Journals (Sweden)

    V. K. C. Venema

    2011-08-01

    Full Text Available The COST (European Cooperation in Science and Technology Action ES0601: Advances in homogenization methods of climate series: an integrated approach (HOME has executed a blind intercomparison and validation study for monthly homogenization algorithms. Time series of monthly temperature and precipitation were evaluated because of their importance for climate studies and because they represent two important types of statistics (additive and multiplicative. The algorithms were validated against a realistic benchmark dataset. The benchmark contains real inhomogeneous data as well as simulated data with inserted inhomogeneities. Random break-type inhomogeneities were added to the simulated datasets modeled as a Poisson process with normally distributed breakpoint sizes. To approximate real world conditions, breaks were introduced that occur simultaneously in multiple station series within a simulated network of station data. The simulated time series also contained outliers, missing data periods and local station trends. Further, a stochastic nonlinear global (network-wide trend was added.

    Participants provided 25 separate homogenized contributions as part of the blind study as well as 22 additional solutions submitted after the details of the imposed inhomogeneities were revealed. These homogenized datasets were assessed by a number of performance metrics including (i the centered root mean square error relative to the true homogeneous value at various averaging scales, (ii the error in linear trend estimates and (iii traditional contingency skill scores. The metrics were computed both using the individual station series as well as the network average regional series. The performance of the contributions depends significantly on the error metric considered. Contingency scores by themselves are not very informative. Although relative homogenization algorithms typically improve the homogeneity of temperature data, only the best ones improve

  17. Fes cycling

    Directory of Open Access Journals (Sweden)

    Berkelmans Rik

    2008-01-01

    Full Text Available Many research with functional electrical stimulation (FES has been done to regain mobility and for health benefits. Better results have been reported for FES-cycling than for FES-walking. The majority of the subjects during such research are people with a spinal cord injury (SCI, cause they often lost skin sensation. Besides using surface stimulation also implanted stimulators can be used. This solves the skin sensation problem, but needs a surgery. Many physiological effects of FES-cycling has been reported, e.g., increase of muscles, better blood flow, reduction of pressure ulcers, improved self-image and some reduction of bone mineral density (BMD loss. Also people with an incomplete SCI benefit by FES-cycling, e.g. cycling time without FES, muscle strength and also the walking abilities increased. Hybrid exercise gives an even better cardiovascular training. Presently 4 companies are involved in FES-cycling. They all have a stationary mobility trainer. Two of them also use an outdoor tricycle. One combined with voluntary arm cranking. By optimizing the stimulation parameters the power output and fatigue resistance will increase, but will still be less compared to voluntary cycling.

  18. Chemistry of post-annealing of epitaxial CoFe{sub 2}O{sub 4} thin films

    Energy Technology Data Exchange (ETDEWEB)

    Axelsson, Anna-Karin, E-mail: a.k.axelsson@imperial.ac.u [Imperial College London, Department of Materials, Exhibition Road, SW7 2AZ, London (United Kingdom); Valant, Matjaz, E-mail: matjaz.valant@p-ng.s [Imperial College London, Department of Materials, Exhibition Road, SW7 2AZ, London (United Kingdom); University of Nova Gorica, Materials Research Laboratory, Vipavska 13, 5000 Nova Gorica (Slovenia); Fenner, Laura, E-mail: laura.fenner@ucl.ac.u [University College London, Department of Chemistry, Christopher Ingold Laboratories, 20 Gordon Street, WC1H 0AJ, London (United Kingdom); Wills, Andrew S., E-mail: a.s.wills@ucl.ac.u [University College London, Department of Chemistry, Christopher Ingold Laboratories, 20 Gordon Street, WC1H 0AJ, London (United Kingdom); Alford, Neil McN, E-mail: n.alford@imperial.ac.u [Imperial College London, Department of Materials, Exhibition Road, SW7 2AZ, London (United Kingdom)

    2009-05-01

    CoFe{sub 2}O{sub 4} thin films of different thicknesses were grown on SrTiO{sub 3} substrates. The X-ray diffraction analysis and atomic force microscopy indicated both epitaxy and a granular microstructure. We studied the magnetic properties of these films as a function of oxygen post-annealing and film thickness. All as-deposited films exhibited similar magnetic properties with saturated magnetization (M{sub s}) of approximately 50% of the bulk M{sub s}, (80 Am{sup 2} kg{sup -1}). After the post-annealing the M{sub s} changes as a consequence of crystallographic restructuring of the film. Cation ordering in 100 nm thick films reduces M{sub s}, whereas re-oxidation increases M{sub s} for thinner films. 13 nm films, annealed for 1 h, reach the bulk M{sub s}. For even thinner films the quantum-size effect reduces M{sub s}. For a synthesis of {>=} 30 nm films an annealing cycle after deposition of every 15 nm layer is recommended.

  19. Influence of Initial Microstructure on Microstructural Stability and Mechanical Behavior of Cryorolled A356 Alloy Subjected to Annealing

    Science.gov (United States)

    Immanuel, R. J.; Panigrahi, S. K.

    2017-08-01

    In the present work, various heat treatment cycles are imposed on an A356 aluminum alloy to develop two different base microstructures, one with supersaturated aluminum matrix and the other with coarse and uniformly distributed precipitates. Both the developed materials are subjected to cryorolling and then isochronally annealed for 1 hour at various temperatures ranging from 373 K to 673 K (100 °C to 400 °C). The overall strength is maximum for the cryorolled material with supersaturated base microstructure due to the dominant dislocation strengthening and precipitation strengthening mechanisms. However, the cryorolled material with precipitated base microstructure is found to have superior microstructural stability with retained ultrafine-grained (UFG) microstructure up to the annealing temperature of 473 K (200 °C) due to effective grain boundary pinning by the precipitates. Also, the material retains about 85 pct of as-cryorolled strength with enhanced ductility even after annealing at 473 K (200 °C). A detailed investigation on the microstructural evolution of the material at various annealing temperatures along with their mechanical behavior is presented in this article.

  20. An adaptive approach to the physical annealing strategy for simulated annealing

    Science.gov (United States)

    Hasegawa, M.

    2013-02-01

    A new and reasonable method for adaptive implementation of simulated annealing (SA) is studied on two types of random traveling salesman problems. The idea is based on the previous finding on the search characteristics of the threshold algorithms, that is, the primary role of the relaxation dynamics in their finite-time optimization process. It is shown that the effective temperature for optimization can be predicted from the system's behavior analogous to the stabilization phenomenon occurring in the heating process starting from a quenched solution. The subsequent slow cooling near the predicted point draws out the inherent optimizing ability of finite-time SA in more straightforward manner than the conventional adaptive approach.

  1. 77 FR 20493 - National Child Abuse Prevention Month, 2012

    Science.gov (United States)

    2012-04-05

    ... Documents#0;#0; ] Proclamation 8791 of April 2, 2012 National Child Abuse Prevention Month, 2012 By the... National Child Abuse Prevention Month, we renew our commitment to break the cycle of violence, strengthen... half a million American children suffer neglect or abuse every year. A strong and well-informed family...

  2. Thermal annealing effects on vanadium pentoxide xerogel films

    National Research Council Canada - National Science Library

    G. N. Barbosa; C. F.O. Graeff; H. P. Oliveira

    2005-01-01

    The effect of water molecules on the conductivity and electrochemical properties of vanadium pentoxide xerogel was studied in connection with changes of morphology upon thermal annealing at different temperatures...

  3. Solvent vapor annealing of an insoluble molecular semiconductor

    KAUST Repository

    Amassian, Aram

    2010-01-01

    Solvent vapor annealing has been proposed as a low-cost, highly versatile, and room-temperature alternative to thermal annealing of organic semiconductors and devices. In this article, we investigate the solvent vapor annealing process of a model insoluble molecular semiconductor thin film - pentacene on SiO 2 exposed to acetone vapor - using a combination of optical reflectance and two-dimensional grazing incidence X-ray diffraction measurements performed in situ, during processing. These measurements provide valuable and new insight into the solvent vapor annealing process; they demonstrate that solvent molecules interact mainly with the surface of the film to induce a solid-solid transition without noticeable swelling, dissolving or melting of the molecular material. © 2010 The Royal Society of Chemistry.

  4. Evidence for quantum annealing with more than one hundred qubits

    Science.gov (United States)

    Boixo, Sergio; Rønnow, Troels F.; Isakov, Sergei V.; Wang, Zhihui; Wecker, David; Lidar, Daniel A.; Martinis, John M.; Troyer, Matthias

    2014-03-01

    Quantum technology is maturing to the point where quantum devices, such as quantum communication systems, quantum random number generators and quantum simulators may be built with capabilities exceeding classical computers. A quantum annealer, in particular, solves optimization problems by evolving a known initial configuration at non-zero temperature towards the ground state of a Hamiltonian encoding a given problem. Here, we present results from tests on a 108 qubit D-Wave One device based on superconducting flux qubits. By studying correlations we find that the device performance is inconsistent with classical annealing or that it is governed by classical spin dynamics. In contrast, we find that the device correlates well with simulated quantum annealing. We find further evidence for quantum annealing in the form of small-gap avoided level crossings characterizing the hard problems. To assess the computational power of the device we compare it against optimized classical algorithms.

  5. Improved mapping of the travelling salesman problem for quantum annealing

    Science.gov (United States)

    Troyer, Matthias; Heim, Bettina; Brown, Ethan; Wecker, David

    2015-03-01

    We consider the quantum adiabatic algorithm as applied to the travelling salesman problem (TSP). We introduce a novel mapping of TSP to an Ising spin glass Hamiltonian and compare it to previous known mappings. Through direct perturbative analysis, unitary evolution, and simulated quantum annealing, we show this new mapping to be significantly superior. We discuss how this advantage can translate to actual physical implementations of TSP on quantum annealers.

  6. Structural and magnetic changes on annealing permalloy/copper multilayers

    Energy Technology Data Exchange (ETDEWEB)

    Fulthorpe, B.D.; Hase, T.P.A. E-mail: t.p.a.hase@dur.ac.uk; Tanner, B.K.; Marrows, C.H.; Hickey, B.J

    2001-05-01

    Thin-film powder diffraction and in situ grazing incidence X-ray scattering have been used to determine the structural changes that occur during annealing of permalloy/copper multilayers. We show that the enhanced stability in the magnetotransport properties of multilayers doped with cobalt at the interfaces correlates with reduced interdiffusion. The development of a long correlation length conformal roughness during annealing is observed.

  7. A simulated annealing technique for multi-objective simulation optimization

    OpenAIRE

    Mahmoud H. Alrefaei; Diabat, Ali H.

    2009-01-01

    In this paper, we present a simulated annealing algorithm for solving multi-objective simulation optimization problems. The algorithm is based on the idea of simulated annealing with constant temperature, and uses a rule for accepting a candidate solution that depends on the individual estimated objective function values. The algorithm is shown to converge almost surely to an optimal solution. It is applied to a multi-objective inventory problem; the numerical results show that the algorithm ...

  8. Stored energy and annealing behavior of heavily deformed aluminium

    DEFF Research Database (Denmark)

    Kamikawa, Naoya; Huang, Xiaoxu; Kondo, Yuka

    2012-01-01

    followed by 0.5 h annealing at 200-600°C, where the former treatment leads to discontinuous recrystallization and the latter to uniform structural coarsening. This behavior has been analyzed in terms of the relative change during annealing of energy stored as elastic energy in the dislocation structure...... and as boundary energy in the high-angle boundaries. © (2012) Trans Tech Publications, Switzerland....

  9. Monthly, global emissions of carbon dioxide from fossil fuel consumption

    DEFF Research Database (Denmark)

    Andres, R.J.; Gregg, Jay Sterling; Losey, L.

    2011-01-01

    This paper examines available data, develops a strategy and presents a monthly, global time series of fossil-fuel carbon dioxide emissions for the years 1950–2006. This monthly time series was constructed from detailed study of monthly data from the 21 countries that account for approximately 80...... reproduces monthly patterns in the data and the global monthly pattern of emissions is relatively insensitive to the exact proxy assignments used. The data and results presented here should lead to a better understanding of global and regional carbon cycles, especially when the mass data are combined...... with the stable carbon isotope data in atmospheric transport models....

  10. Petroleum supply monthly

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-10-01

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blends, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  11. Petroleum Supply Monthly

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  12. COSMIC monthly progress report

    Science.gov (United States)

    1994-01-01

    Activities of the Computer Software Management and Information Center (COSMIC) are summarized for the month of May 1994. Tables showing the current inventory of programs available from COSMIC are presented and program processing and evaluation activities are summarized. Nine articles were prepared for publication in the NASA Tech Brief Journal. These articles (included in this report) describe the following software items: (1) WFI - Windowing System for Test and Simulation; (2) HZETRN - A Free Space Radiation Transport and Shielding Program; (3) COMGEN-BEM - Composite Model Generation-Boundary Element Method; (4) IDDS - Interactive Data Display System; (5) CET93/PC - Chemical Equilibrium with Transport Properties, 1993; (6) SDVIC - Sub-pixel Digital Video Image Correlation; (7) TRASYS - Thermal Radiation Analyzer System (HP9000 Series 700/800 Version without NASADIG); (8) NASADIG - NASA Device Independent Graphics Library, Version 6.0 (VAX VMS Version); and (9) NASADIG - NASA Device Independent Graphics Library, Version 6.0 (UNIX Version). Activities in the areas of marketing, customer service, benefits identification, maintenance and support, and dissemination are also described along with a budget summary.

  13. Population annealing simulations of a binary hard-sphere mixture

    Science.gov (United States)

    Callaham, Jared; Machta, Jonathan

    2017-06-01

    Population annealing is a sequential Monte Carlo scheme well suited to simulating equilibrium states of systems with rough free energy landscapes. Here we use population annealing to study a binary mixture of hard spheres. Population annealing is a parallel version of simulated annealing with an extra resampling step that ensures that a population of replicas of the system represents the equilibrium ensemble at every packing fraction in an annealing schedule. The algorithm and its equilibration properties are described, and results are presented for a glass-forming fluid composed of a 50/50 mixture of hard spheres with diameter ratio of 1.4:1. For this system, we obtain precise results for the equation of state in the glassy regime up to packing fractions φ ≈0.60 and study deviations from the Boublik-Mansoori-Carnahan-Starling-Leland equation of state. For higher packing fractions, the algorithm falls out of equilibrium and a free volume fit predicts jamming at packing fraction φ ≈0.667 . We conclude that population annealing is an effective tool for studying equilibrium glassy fluids and the jamming transition.

  14. Synthesis and characterization of Ar-annealed zinc oxide nanostructures

    Directory of Open Access Journals (Sweden)

    Narayanan Kuthirummal

    2016-09-01

    Full Text Available Nanostructured zinc oxide samples were synthesized through CVD and annealed in argon. The samples were investigated using SEM, TEM, XRD, and UV/VIS/FTIR photoacoustic spectroscopy. The SEM/TEM images show relatively spherical particles that form elongated, connected domains post-anneal. XRD measurements indicate a typical wurtzite structure and reveal an increase in average grain size from 16.3 nm to 21.2 nm in Ar-annealed samples over pristine samples. Visible photoacoustic spectra reveal the contribution of defect levels on the absorption edge of the fundamental gap of zinc oxide. The steepness parameter of the absorption edge, which is inversely proportional to the width of the absorption edge, decreased from 0.1582 (pristine to 0.1539 (annealed for 90 minutes revealing increased density of defect states upon annealing. The FTIR photoacoustic spectra show an intense peak at 412 cm-1 and a shoulder at 504 cm-1 corresponding to the two transverse optical stretching modes of ZnO. These results may indicate a self-assembly mechanism upon anneal under Ar atmosphere leading to early-stage nanorod growth.

  15. Rapid hardening induced by electric pulse annealing in nanostructured pure aluminum

    DEFF Research Database (Denmark)

    Zeng, Wei; Shen, Yao; Zhang, Ning

    2012-01-01

    Nanostructured pure aluminum was fabricated by heavy cold-rolling and then subjected to recovery annealing either by applying electric pulse annealing or by traditional air furnace annealing. Both annealing treatments resulted in an increase in yield strength due to the occurrence of a “dislocation...

  16. Glacial cycles

    DEFF Research Database (Denmark)

    Kaufmann, R. K.; Juselius, Katarina

    We use a statistical model, the cointegrated vector autoregressive model, to assess the degree to which variations in Earth's orbit and endogenous climate dynamics can be used to simulate glacial cycles during the late Quaternary (390 kyr-present). To do so, we estimate models of varying complexity...... and compare the accuracy of their in-sample simulations. Results indicate that strong statistical associations between endogenous climate variables are not enough for statistical models to reproduce glacial cycles. Rather, changes in solar insolation associated with changes in Earth's orbit are needed...

  17. Influence of multi-deposition multi-annealing on time-dependent dielectric breakdown characteristics of PMOS with high-/metal gate last process

    Institute of Scientific and Technical Information of China (English)

    王艳蓉; 朱慧珑; 赵超; 陈大鹏; 叶甜春; 杨红; 徐昊; 王晓磊; 罗维春; 祁路伟; 张淑祥; 王文武; 闫江

    2015-01-01

    A multi-deposition multi-annealing technique (MDMA) is introduced into the process of high-k/metal gate MOSFET for the gate last process to effectively reduce the gate leakage and improve the device’s performance. In this paper, we systematically investigate the electrical parameters and the time-dependent dielectric breakdown (TDDB) characteristics of positive channel metal oxide semiconductor (PMOS) under different MDMA process conditions, including the depo-sition/annealing (D&A) cycles, the D&A time, and the total annealing time. The results show that the increases of the number of D&A cycles (from 1 to 2) and D&A time (from 15 s to 30 s) can contribute to the results that the gate leakage current decreases by about one order of magnitude and that the time to fail (TTF) at 63.2% increases by about several times. However, too many D&A cycles (such as 4 cycles) make the equivalent oxide thickness (EOT) increase by about 1 ˚A and the TTF of PMOS worsen. Moreover, different D&A times and numbers of D&A cycles induce different breakdown mechanisms.

  18. Annealing effects on strain and stress sensitivity of polymer optical fibre based sensors

    DEFF Research Database (Denmark)

    Pospori, A.; Marques, C. A. F.; Zubel, M. G.

    2016-01-01

    The annealing effects on strain and stress sensitivity of polymer optical fibre Bragg grating sensors after their photoinscription are investigated. PMMA optical fibre based Bragg grating sensors are first photo-inscribed and then they were placed into hot water for annealing. Strain, stress...... and force sensitivity measurements are taken before and after annealing. Parameters such as annealing time and annealing temperature are investigated. The change of the fibre diameter due to water absorption and the annealing process is also considered. The results show that annealing the polymer optical...... fibre tends to increase the strain, stress and force sensitivity of the photo-inscribed sensor....

  19. Happy Cycling

    DEFF Research Database (Denmark)

    Geert Jensen, Birgitte; Nielsen, Tom

    2013-01-01

    og Interaktions Design, Aarhus Universitet under opgave teamet: ”Happy Cycling City – Aarhus”. Udfordringen i studieopgaven var at vise nye attraktive løsningsmuligheder i forhold til cyklens og cyklismens integration i byrum samt at påpege relationen mellem design og overordnede diskussioner af...

  20. Glacial cycles

    DEFF Research Database (Denmark)

    Kaufmann, R. K.; Juselius, Katarina

    and compare the accuracy of their in-sample simulations. Results indicate that strong statistical associations between endogenous climate variables are not enough for statistical models to reproduce glacial cycles. Rather, changes in solar insolation associated with changes in Earth's orbit are needed...

  1. Koszul cycles

    CERN Document Server

    Bruns, Winfreid; Römer, Tim

    2010-01-01

    We prove regularity bounds for Koszul cycles holding for every ideal of dimension at most 1 in a polynomial ring. We generalize the lower bound for the Green-Lazarsfeld index of Veronese rings we proved in arXiv:0902.2431 to the multihomogeneous setting.

  2. Large recovery strain in Fe-Mn-Si-based shape memory steels obtained by engineering annealing twin boundaries.

    Science.gov (United States)

    Wen, Y H; Peng, H B; Raabe, D; Gutierrez-Urrutia, I; Chen, J; Du, Y Y

    2014-09-17

    Shape memory alloys are a unique class of materials that can recover their original shape upon heating after a large deformation. Ti-Ni alloys with a large recovery strain are expensive, while low-cost conventional processed Fe-Mn-Si-based steels suffer from a low recovery strain (twin boundaries. Reducing the density of twin boundaries is thus a critical factor for obtaining a large recovery strain in these steels. By significantly suppressing the formation of twin boundaries, we attain a tensile recovery strain of 7.6% in an annealed cast polycrystalline Fe-20.2Mn-5.6Si-8.9Cr-5.0Ni steel (weight%). Further attractiveness of this material lies in its low-cost alloying components and simple synthesis-processing cycle consisting only of casting plus annealing. This enables these steels to be used at a large scale as structural materials with advanced functional properties.

  3. Elimination of bubbles and improvement of the superconducting properties in MgB2 films annealed using electron beam

    Science.gov (United States)

    Xu, Zhuang; Kong, Xiangdong; Han, Li; Pang, Hua; Wu, Yue; Gao, Zhaoshun; Li, Xiaona

    2017-03-01

    MgB2 superconducting films can be readily obtained using the electron-beam annealing method. However, many bubbles existing in the film severely damage the surface morphology, which is known as the deleterious current-limiting mechanism. Based on morphology images and energy-dispersive spectroscopy spectra, we found that, during the annealing process, solid Mg-rich layers evaporate to form Mg vapour in the precursor film, resulting in bubbles in the film. By reducing the cycle thickness of the precursor film, we obtained MgB2 films with better properties. The root-mean-square surface roughness was 2.7 nm over a 10 × 10 μm area for a 100 nm-thick film, and the critical current density at 20 K was increased to 3.8 × 106 A cm‑2. These MgB2 films are suitable for fabricating MgB2 superconducting devices.

  4. Multiple implantation and multiple annealing of phosphorus doped germanium to achieve n-type activation near the theoretical limit

    Science.gov (United States)

    Kim, Jeehwan; Bedell, Stephen W.; Sadana, Devendra K.

    2012-09-01

    Full activation of n-type dopant in germanium (Ge) reaching to its solid solubility has never been achieved by using ion implantation doping technique. This is because implantation of dopants always leaves defects such as vacancy and interstitials in the Ge crystal. While implantation-induced defects are electrically neutral for the most of semiconductor materials, they are electrically positive for Ge resulting in compensation of n-type dopants. In this Letter, we verified that 5 × 1019 P/cm3 is the maximum active concentration, which can be fully activated in germanium "without leaving implantation damage" per implantation/annealing cycle. The repetition of implantation and annealing of phosphorous (P) with the concentration of 5 × 1019 cm-3 leads to the activation of 1 × 1020 P/cm3 close to its solid solubility limit of 2 × 1020 P/cm3.

  5. Note: Improving long-term stability of hot-wire anemometer sensors by means of annealing

    Science.gov (United States)

    Lundström, H.

    2015-08-01

    Annealing procedures for hot-wire sensors of platinum and platinum-plated tungsten have been investigated experimentally. It was discovered that the two investigated sensor metals behave quite differently during the annealing process, but for both types annealing may improve long-term stability considerably. Measured drift of sensors both without and with prior annealing is presented. Suggestions for suitable annealing temperatures and times are given.

  6. Note: Improving long-term stability of hot-wire anemometer sensors by means of annealing.

    Science.gov (United States)

    Lundström, H

    2015-08-01

    Annealing procedures for hot-wire sensors of platinum and platinum-plated tungsten have been investigated experimentally. It was discovered that the two investigated sensor metals behave quite differently during the annealing process, but for both types annealing may improve long-term stability considerably. Measured drift of sensors both without and with prior annealing is presented. Suggestions for suitable annealing temperatures and times are given.

  7. Note: Improving long-term stability of hot-wire anemometer sensors by means of annealing

    Energy Technology Data Exchange (ETDEWEB)

    Lundström, H., E-mail: hans.lundstrom@hig.se [Department of Building, Energy and Environmental Engineering, University of Gävle, SE-801 76 Gävle (Sweden)

    2015-08-15

    Annealing procedures for hot-wire sensors of platinum and platinum-plated tungsten have been investigated experimentally. It was discovered that the two investigated sensor metals behave quite differently during the annealing process, but for both types annealing may improve long-term stability considerably. Measured drift of sensors both without and with prior annealing is presented. Suggestions for suitable annealing temperatures and times are given.

  8. Annealing behaviors of vacancy in varied neutron irradiated Czochralski silicon

    Institute of Scientific and Technical Information of China (English)

    CHEN Gui-feng; LI Yang-xian; LIU Li-li; NIU Ping-juan; NIU Sheng-li; CHEN Dong-feng

    2006-01-01

    The difference of annealing behaviors of vacancy-oxygen complex (VO) in varied dose neutron irradiated Czochralski silicon: (S1 5×1017 n/cm3 and S2 1.07×1019 n/cm3) were studied. The results show that the VO is one of the main defects formed in neutron irradiated Czochralski silicon (CZ-Si). In this defect,oxygen atom shares a vacancy,it is bonded to two silicon neighbors. Annealed at 200 ℃,divacancies are trapped by interstitial oxygen(Oi) to form V2O (840 cm-1). With the decrease of the 829 cm-1 (VO) three infrared absorption bands at 825 cm-1 (V2O2),834 cm-1 (V2O3) and 840 cm-1 (V2O) will rise after annealed at temperature range of 200-500 ℃. After annealed at 450-500 ℃ the main absorption bands in S1 sample are 834 cm-1,825 cm-1 and 889 cm-1 (VO2),in S2 is 825 cm-1. Annealing of A-center in varied neutron irradiated CZ-Si is suggested to consist of two processes. The first is due to trapping of VO by Oi in low dose neutron irradiated CZ-Si (S1) and the second is due to capture the wandering vacancy by VO,etc,in high dose neutron irradiated CZ-Si (S2),the VO2 plays an important role in the annealing of A-center. With the increase of the irradiation dose,the annealing behavior of A-center is changed.

  9. Distinct Cdk1 requirements during single-strand annealing, noncrossover, and crossover recombination.

    Directory of Open Access Journals (Sweden)

    Camilla Trovesi

    2011-08-01

    Full Text Available Repair of DNA double-strand breaks (DSBs by homologous recombination (HR in haploid cells is generally restricted to S/G2 cell cycle phases, when DNA has been replicated and a sister chromatid is available as a repair template. This cell cycle specificity depends on cyclin-dependent protein kinases (Cdk1 in Saccharomyces cerevisiae, which initiate HR by promoting 5'-3' nucleolytic degradation of the DSB ends. Whether Cdk1 regulates other HR steps is unknown. Here we show that yku70Δ cells, which accumulate single-stranded DNA (ssDNA at the DSB ends independently of Cdk1 activity, are able to repair a DSB by single-strand annealing (SSA in the G1 cell cycle phase, when Cdk1 activity is low. This ability to perform SSA depends on DSB resection, because both resection and SSA are enhanced by the lack of Rad9 in yku70Δ G1 cells. Furthermore, we found that interchromosomal noncrossover recombinants are generated in yku70Δ and yku70Δ rad9Δ G1 cells, indicating that DSB resection bypasses Cdk1 requirement also for carrying out these recombination events. By contrast, yku70Δ and yku70Δ rad9Δ cells are specifically defective in interchromosomal crossover recombination when Cdk1 activity is low. Thus, Cdk1 promotes DSB repair by single-strand annealing and noncrossover recombination by acting mostly at the resection level, whereas additional events require Cdk1-dependent regulation in order to generate crossover outcomes.

  10. Laser annealing of textured thin film cathode material for lithium ion batteries

    Science.gov (United States)

    Kohler, R.; Bruns, M.; Smyrek, P.; Ulrich, S.; Przybylski, M.; Pfleging, W.

    2010-02-01

    The material development for advanced lithium ion batteries plays an important role in future mobile applications and energy storage systems. It is assumed that electrode materials made of nano-composited materials will improve battery lifetime and will lead to an enhancement of lithium diffusion and thus improve battery capacity and cyclability. Lithium cobalt oxide (LiCoO2) is commonly used as a cathode material. Thin films of this electrode material were synthesized by non-reactive r.f. magnetron sputtering of LiCoO2 targets on silicon or stainless steel substrates. For the formation of the high temperature phase of LiCoO2 (HT-LiCoO2), which exhibits good electrochemical performance with a specific capacity of 140 mAh/g and high capacity retention, a subsequent annealing treatment is necessary. For this purpose laser annealing of thin film LiCoO2 was investigated in detail and compared to conventional furnace annealing. A high power diode laser system operating at a wavelength of 940 nm with an integrated pyrometer for temperature control was used. Different temperatures (between 200°C and 700°C) for the laser structured and unstructured thin films were applied. The effects of laser treatment on the LiCoO2 thin films studied with Raman spectroscopy, X-ray photoelectron spectroscopy and X-ray diffraction to determine their stoichiometry and crystallinity. The development of HT-LiCoO2 and also the formation of a Co3O4 phase were discussed. The electrochemical properties of the manufactured films were investigated via electrochemical cycling against a lithium anode.

  11. Electronic Services Monthly MI Report

    Data.gov (United States)

    Social Security Administration — This electronic services monthly MI report contains monthly MI data for most public facing online online applications such as iClaim, electronic access, Mobile wage...

  12. Effect of annealing temperature on microstructure and electrochemical performance of La0.75Mg0.25Ni3.5Co0.2 hydrogen storage electrode alloy

    Institute of Scientific and Technical Information of China (English)

    DONG Xiaoping; L(U) Fanxiu; ZHANG Yanghuan; YANG Liying; WANG Xinlin

    2008-01-01

    To improve the cyclic stability of La-Mg-Ni system alloy, as-cast La0.75Mg0.25Ni3.5Co0.2 alloy was annealed at 1123, 1223, and 1323 K for 10 h in 0.3 MPa argon. The microstructure and electrochemical performance of different annealed alloys were investigated systematically by X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), X-Ray Photoelectron Spectroscopy (XPS), and electrochemical experiments. The results obtained by XRD and SEM showed that the as-cast and annealed (1123 K) alloys had multiphase structure containing LaNi5, (La, Mg)2(Ni, Co)7 and few LaNi2 phases. When annealing temperatures approached 1223 and 1323 K, LaNi2 phase disappeared. The annealed alloys at 1223 and 1323 K were composed of LaNi5, (La, Mg)2(Ni, Co)7 and (La, Mg)(Ni, Co)3 phases. With increasing annealing temperature, the maximum discharge capacity of the alloy decreased monotonously, but the cyclic stability was improved owing to structure homogeneity and grain growth after annealing, as well as the enhancement of anti-oxidation/corrosion ability and the suppression of pulverization during cycling in KOH electrolyte.

  13. Influence of annealing treatment on the hydrogen storage properties of La{sub 2-x}Ti{sub x}MgNi{sub 9} (x = 0.2, 0.3) alloys

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Weiqing; Lan, Zhiqiang; Wenlou, Wei; Yixin, Liu [Key Laboratory of National Education Ministry for Nonferrous Metals and Materials Processing Technology, College of Physics Science and Technology, Guangxi University, Nanning 530004 (China); Guo, Jin [Key Laboratory of National Education Ministry for Nonferrous Metals and Materials Processing Technology, College of Physics Science and Technology, Guangxi University, Nanning 530004 (China); International Centre for Materials Physics, Chinese Academy of Sciences, Shenyang 110016 (China)

    2010-10-15

    La{sub 2-x}Ti{sub x}MgNi{sub 9} (x = 0.2, 0.3) alloys have been prepared by magnetic levitation melting under an Argon atmosphere, and the as-cast alloys were annealed at 800 C, 900 C for 10 h under vacuum. The effects of annealing on the hydrogen storage properties of the alloys were investigated systematically by XRD, PCT and electrochemical measurements. For the La{sub 2-x}Ti{sub x}MgNi{sub 9} (x = 0.2, 0.3) alloys, LaNi{sub 5}, LaMg{sub 2}Ni{sub 9} and LaNi{sub 3} are the main phases and a Ti{sub 2}Ni phase appears at 900 C. The effective hydrogen storage capacity increases from 1.10, 1.10 wt.% (as-cast) to 1.22, 1.16 wt.% (annealed 800 C) and 1.31, 1.27 wt.% (annealed 900 C), respectively. The annealing not only improves the hydrogen absorption/desorption kinetics but also increases the maximum discharge capacity and enhances the cycling stability. The La{sub 1.8}Ti{sub 0.2}MgNi{sub 9} alloy annealed at 900 C exhibits good electrochemical properties, and the discharge capacities decrease from 366.1 mA h/g to 219.6 mA h/g after 177 charge-discharge cycles. (author)

  14. Electrochemical effects of annealing on atomic layer deposited Al2O3 coatings on LiNi0.5Mn0.3Co0.2O2

    Science.gov (United States)

    Jackson, David H. K.; Kuech, Thomas F.

    2017-10-01

    This study investigated the annealing of atomic layer deposited (ALD) Al2O3 coated onto Li-ion battery cathodes to enhance their electrochemical properties. LiNi0.5Mn0.3Co0.2O2 (NMC) cathode powders were coated with 5 ALD cycles at 100 °C, annealed between 300 and 700 °C, cast into electrode sheets and assembled into coin cells. Cells were characterized using charge-discharge cycling, electrochemical impedance spectroscopy, pre-casting and postmortem X-ray photoelectron spectroscopy, and charge endpoint slippage measurement. Diffusion of Al into bulk NMC was observable at ≥500 °C, and extent of diffusion increased with increasing temperature. Un-annealed ALD-coated cathodes showed exceptional capacity retention at high charge-discharge rates, while annealed cells showed recovery of initial charge capacity lost upon ALD coating. High quantities of LiF forming surface species were detected in cells annealed at 500 °C. This study approaches post-deposition annealing as a parameter that may be used to explore the electrochemical properties of ALD-coated battery cathodes.

  15. Spall response of annealed copper to direct explosive loading

    Science.gov (United States)

    Finnegan, S. G.; Burns, M. J.; Markland, L.; Goff, M.; Ferguson, J. W.

    2017-01-01

    Taylor wave spall experiments were conducted on annealed copper targets using direct explosive loading. The targets were mounted on the back of an explosive disc which was being used for a shock to detonation transition (SDT) test in a gas gun. This technique allows two experiments to be conducted with one piece of explosive. Explosive loading creates a high stress state within the target with a lower strain rate than an equivalent plate impact experiment, although the shock front will also have some curvature. Three shots were performed on two differently annealed batches of copper to investigate the viability of the technique and the effect of annealing on the spall response. One pair of targets was annealed at 850°C for four hours and the other target was annealed at 600°C for one hour. The free surface velocity (FSV) profiles were recorded using a Photonic Doppler Velocimetry (PDV) probe focused on the center of the target. The profiles were compared to predictions from the CREST reactive burn model. One profile recorded a significantly lower peak velocity which was attributed to the probe being located off center. Despite this, all three calculated spall strengths closely agreed and it was concluded that the technique is a viable one for loading an inert target.

  16. High pressure annealing of Europium implanted GaN

    KAUST Repository

    Lorenz, K.

    2012-02-09

    GaN epilayers were implanted with Eu to fluences of 1×10^13 Eu/cm2 and 1×10^15 Eu/cm2. Post-implant thermal annealing was performed in ultra-high nitrogen pressures at temperatures up to 1450 ºC. For the lower fluence effective structural recovery of the crystal was observed for annealing at 1000 ºC while optical activation could be further improved at higher annealing temperatures. The higher fluence samples also reveal good optical activation; however, some residual implantation damage remains even for annealing at 1450 ºC which leads to a reduced incorporation of Eu on substitutional sites, a broadening of the Eu luminescence lines and to a strongly reduced fraction of optically active Eu ions. Possibilities for further optimization of implantation and annealing conditions are discussed.© (2012) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.

  17. Experimental quantum annealing: case study involving the graph isomorphism problem.

    Science.gov (United States)

    Zick, Kenneth M; Shehab, Omar; French, Matthew

    2015-06-08

    Quantum annealing is a proposed combinatorial optimization technique meant to exploit quantum mechanical effects such as tunneling and entanglement. Real-world quantum annealing-based solvers require a combination of annealing and classical pre- and post-processing; at this early stage, little is known about how to partition and optimize the processing. This article presents an experimental case study of quantum annealing and some of the factors involved in real-world solvers, using a 504-qubit D-Wave Two machine and the graph isomorphism problem. To illustrate the role of classical pre-processing, a compact Hamiltonian is presented that enables a reduced Ising model for each problem instance. On random N-vertex graphs, the median number of variables is reduced from N(2) to fewer than N log2 N and solvable graph sizes increase from N = 5 to N = 13. Additionally, error correction via classical post-processing majority voting is evaluated. While the solution times are not competitive with classical approaches to graph isomorphism, the enhanced solver ultimately classified correctly every problem that was mapped to the processor and demonstrated clear advantages over the baseline approach. The results shed some light on the nature of real-world quantum annealing and the associated hybrid classical-quantum solvers.

  18. Laser annealing heals radiation damage in avalanche photodiodes

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Jin Gyu [University of Waterloo, Institute for Quantum Computing, Waterloo, ON (Canada); University of Waterloo, Department of Electrical and Computer Engineering, Waterloo, ON (Canada); Anisimova, Elena; Higgins, Brendon L.; Bourgoin, Jean-Philippe [University of Waterloo, Institute for Quantum Computing, Waterloo, ON (Canada); University of Waterloo, Department of Physics and Astronomy, Waterloo, ON (Canada); Jennewein, Thomas [University of Waterloo, Institute for Quantum Computing, Waterloo, ON (Canada); University of Waterloo, Department of Physics and Astronomy, Waterloo, ON (Canada); Canadian Institute for Advanced Research, Quantum Information Science Program, Toronto, ON (Canada); Makarov, Vadim [University of Waterloo, Institute for Quantum Computing, Waterloo, ON (Canada); University of Waterloo, Department of Electrical and Computer Engineering, Waterloo, ON (Canada); University of Waterloo, Department of Physics and Astronomy, Waterloo, ON (Canada)

    2017-12-15

    Avalanche photodiodes (APDs) are a practical option for space-based quantum communications requiring single-photon detection. However, radiation damage to APDs significantly increases their dark count rates and thus reduces their useful lifetimes in orbit. We show that high-power laser annealing of irradiated APDs of three different models (Excelitas C30902SH, Excelitas SLiK, and Laser Components SAP500S2) heals the radiation damage and several APDs are restored to typical pre-radiation dark count rates. Of nine samples we test, six APDs were thermally annealed in a previous experiment as another solution to mitigate the radiation damage. Laser annealing reduces the dark count rates further in all samples with the maximum dark count rate reduction factor varying between 5.3 and 758 when operating at -80 C. This indicates that laser annealing is a more effective method than thermal annealing. The illumination power to reach these reduction factors ranges from 0.8 to 1.6 W. Other photon detection characteristics, such as photon detection efficiency, timing jitter, and afterpulsing probability, fluctuate but the overall performance of quantum communications should be largely unaffected by these variations. These results herald a promising method to extend the lifetime of a quantum satellite equipped with APDs. (orig.)

  19. Photoluminescence evolution in self-ion-implanted and annealed silicon

    Institute of Scientific and Technical Information of China (English)

    Yang Yu; Wang Chong; Yang Rui-Dong; Li Liang; Xiong Fei; Bao Ji-Ming

    2009-01-01

    Si+ ion-implanted silicon wafers are annealed at different temperatures from room temperature to 950℃ and then characterized by using the photoluminescence (PL) technique at different recorded temperatures (RETs). Plentiful optical features are observed and identified clearly in these PL curves. The PL spectra of these samples annealed in different temperature ranges are correspondingly dominated by different emission peaks. Several characteristic features, such as an R line, S bands, a W line, the phonon-assistant W~(TA) and Si~(TO) peaks, can be detected in the PL spectra of samples annealed at different temperatures. For the samples annealed at 800 ℃, emission peaks from the dislocations bounded at the deep energy levels of the forbidden band, such as D_1 and D_2 bands, can be observed at a temperature as high as 280 K. These data strongly indicate that a severe transformation of defect structures could be manipulated by the annealing and recorded temperatures. The deactivation energies of the main optical features are extracted from the PL data at different temperatures.

  20. Annealing-induced shape recovery in thin film metallic glass

    Energy Technology Data Exchange (ETDEWEB)

    Negussie, Alemu Tesfaye; Diyatmika, Wahyu [Department of Materials Science and Engineering, National Taiwan University of Science and Technology, Taipei 10607, Taiwan (China); Chu, J.P., E-mail: jpchu@mail.ntust.edu.tw [Department of Materials Science and Engineering, National Taiwan University of Science and Technology, Taipei 10607, Taiwan (China); Shen, Y.L. [Department of Mechanical Engineering, University of New Mexico, Albuquerque, NM 87131 (United States); Jang, J.S.C. [Department of Mechanical Engineering, National Central University, Chung-Li 32001, Taiwan (China); Hsueh, C.H. [Department of Materials Science and Engineering, National Taiwan University, Taipei 10617, Taiwan (China)

    2014-11-15

    Highlights: • Annealing-induced shape recovery of thin film metallic glass is examined. • Shape recovery becomes obvious with increasing temperature and holding time. • Minimum roughness is obtained when annealed within supercooled liquid region. • The amount of free volume in the film plays a role for the shape recovery. • The numerical simulation confirms the shape recovery upon annealing. - Abstract: The shape recovery property of a sputtered Zr{sub 50.3}Cu{sub 28.1}Al{sub 14}Ni{sub 7.6} (in at.%) thin film metallic glass upon heating is examined. Due to the surface tension-driven viscous flow, the shape of indentation appears to recover to different extents at various temperatures and holding times. It is found that a maximum of 59.8% indentation depth recovery is achieved after annealing within the supercooled liquid region (SCLR). The amount of free volume in the film is found to play a role in the recovery. Atomic force microscopy results reveal a decrease in film roughness to a minimum value within SCLR. To elucidate the experimentally observed shape recovery, a numerical modeling has been employed. It is evident that the depressed region caused by indentation is elevated after annealing.

  1. Laser annealing of silicon surface defects for photovoltaic applications

    Science.gov (United States)

    Sun, Zeming; Gupta, Mool C.

    2016-10-01

    High power lasers are increasingly used for low cost fabrication of solar cell devices. High power laser processes generate crystal defects, which lower the cell efficiency. This study examines the effect of low power laser annealing for the removal of high power laser induced surface defects. The laser annealing behavior is demonstrated by the significant decrease of photoluminescence generated from dislocation-induced defects and the increase of band-to-band emission. This annealing effect is further confirmed by the X-ray diffraction peak reversal. The dislocation density is quantified by observing etch pits under the scanning electron microscope (SEM). For as-melted samples, the dislocation density is decreased to as low as 1.01 × 106 cm- 2 after laser annealing, resulting in an excellent surface carrier lifetime of 920 μs that is comparable to the value of 1240 μs for the silicon starting wafer. For severely defective samples, the dislocation density is decreased by 4 times and the surface carrier lifetime is increased by 5 times after laser annealing.

  2. On simulated annealing phase transitions in phylogeny reconstruction.

    Science.gov (United States)

    Strobl, Maximilian A R; Barker, Daniel

    2016-08-01

    Phylogeny reconstruction with global criteria is NP-complete or NP-hard, hence in general requires a heuristic search. We investigate the powerful, physically inspired, general-purpose heuristic simulated annealing, applied to phylogeny reconstruction. Simulated annealing mimics the physical process of annealing, where a liquid is gently cooled to form a crystal. During the search, periods of elevated specific heat occur, analogous to physical phase transitions. These simulated annealing phase transitions play a crucial role in the outcome of the search. Nevertheless, they have received comparably little attention, for phylogeny or other optimisation problems. We analyse simulated annealing phase transitions during searches for the optimal phylogenetic tree for 34 real-world multiple alignments. In the same way in which melting temperatures differ between materials, we observe distinct specific heat profiles for each input file. We propose this reflects differences in the search landscape and can serve as a measure for problem difficulty and for suitability of the algorithm's parameters. We discuss application in algorithmic optimisation and as a diagnostic to assess parameterisation before computationally costly, large phylogeny reconstructions are launched. Whilst the focus here lies on phylogeny reconstruction under maximum parsimony, it is plausible that our results are more widely applicable to optimisation procedures in science and industry.

  3. Post-annealing effects on the electrochemical performance of a Si/TiSi2 heteronanostructured anode material prepared by mechanical alloying

    Science.gov (United States)

    Shin, Min-Seon; Lee, Taeg-Woo; Park, Jung-Bae; Lim, Sung-Hwan; Lee, Sung-Man

    2017-03-01

    A change in the microstructure of Ti-Si alloys synthesized by high-energy mechanical milling through post-annealing significantly enhances their electrochemical performances as anode materials for lithium-ion batteries (LIBs). The microstructures of ball-milled and post-annealed powders are investigated using high-resolution transmission electron microscopy (HR-TEM). The Si phase is uniformly distributed on the silicide (TiSi2) matrix. The individual Si domains of the mechanical alloying (MA) sample consist of amorphous and crystalline regions with a diffuse interface between the two phases. When MA powder is annealed at 600 °C, the Si phase has a well-developed nanocrystalline microstructure: a multi-grain structure with random orientation of nanometric crystal domains. Annealing at 600 °C causes a significant improvement in electrochemical performance parameters like cycling stability and rate capability. However, when annealed at 800 °C, the electrochemical performances deteriorate due to an increase in the size of Si domains.

  4. The effects of substrate and annealing on structural and electrochemical properties in LiCoO2 thin films prepared by DC magnetron sputtering.

    Science.gov (United States)

    Noh, Jung Pil; Jung, Ki Taek; Cho, Gyu Bong; Lee, Sang Hun; Kim, Ki Won; Nam, Tae Hyun

    2012-07-01

    LiCoO2 thin films were fabricated by direct current magnetron sputtering method on STS304 and Ti substrates. The effects of substrate and annealing on their structural and electrochemical properties of LiCoO2 thin film cathode were studied. Crystal structures and surface morphologies of the deposited films were investigated by X-ray diffraction and field emission scanning electron microscopy. The as-deposited films on both substrates have amorphous structure. The (104) oriented perfect crystallization was obtained by annealing over 600 degrees C in STS304 substrate. The LiCoO2 thin film deposited on Ti substrate shows the (003) texture after annealing at 700 degrees C. The electrochemical properties were investigated by the cyclic voltammetry and charge-discharge measurement. The 600 degrees C-annealed LiCoO2 film deposited on STS304 substrate exhibits the inithial discharge capacity of 22 uAh/cm2 and the 96% capacity retention rate at 50th cycles. The electrochemical measurement on annealed films over 600 degrees C was impossible due to the formed TiO2 insulator layer using Ti substrate. As a result, it was found that the STS304 substrate seems to be more suitable material than the Ti substrate in fabricating LiCoO2 thin film cathode.

  5. Sulfur cycle

    Digital Repository Service at National Institute of Oceanography (India)

    LokaBharathi, P.A.

    :1, the reductive assimilation of sulfate is less important than nitrate. Assimilatory reduction is common among organisms and does not lead to the production of sulfide. The eight-electron reduction of sulfate to sulfide pro- ceeds in different stages. As the ion...; Biogeochemical Approaches to Environmental Risk Assessment; Biogeochemical Models; Biomagnification; Carbon Cycle; Classification and Regression Trees; Climate Change 1: Short-Term Dynamics; Constructed Wetlands, Subsurface Flow; Constructed Wetlands, Surface...

  6. Your Baby's Growth: 3 Months

    Science.gov (United States)

    ... to Be Smart About Social Media Your Baby's Growth: 3 Months KidsHealth > For Parents > Your Baby's Growth: 3 Months Print A A A What's in ... months of life are a period of rapid growth. Your baby will gain about 1 to 1½ ...

  7. Monthly energy review, August 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-08-01

    The Monthly Energy Review for the month of August 1997, presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of U.S. production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors.

  8. Evolution of microstructure and texture during annealing of Al-2.5%Mg-0.2%Sc severely deformed by a combination of accumulative roll bonding (ARB) and conventional rolling

    Science.gov (United States)

    Gatti, J. R.; Bhattacharjee, P. P.

    2015-04-01

    Evolution of microstructure and texture during heavy cold-rolling and annealing of Al-2.5%Mg-0.2%Sc alloy was investigated. For this purpose recrystallized sheets of 1mm thickness having finely dispersed precipitates were processed to 3 cycles of ARB (equivalent strain, εeq=2.4) followed by conventional rolling to a final thickness of 200μm resulting in total equivalent strain of 4.0. Evolution of ultrafine microstructure and strong copper or pure metal type texture were observed during deformation. During annealing very stable microstructure was observed up to 400°C but further annealing resulted in formation of a layered microstructure with deformed layer sandwiched between recrystallized layers. Formation of strong cube texture is not observed in the recrystallized layers. Isothermal annealing for longer time at 500°C leads to abnormal growth of Q orientation ({013}) within the deformed layer.

  9. Fatigue of annealed and cold worked stable and unstable stainless steels

    Science.gov (United States)

    Schuster, G.; Altstetter, C.

    1983-10-01

    Fatigue crack growth rates (FCGR) in AISI 301 and 302 austenitic stainless steel alloys have been measured in controlled load cycles with R = 0.05. Both annealed and cold rolled conditions were examined. The austenite phase of the AISI 301 alloy was unstable under stress and transformed martensitically to α' to a much greater extent than the AISI 302 alloy. At low values of mean stress the unstable alloy had a lower FCGR than the more stable 302 alloy. The FCGR increased with mean stress until values of mean stress ⪞70 MPa, where the FCGR was independent of mean stress and was the same for both alloys. Various metallographic and macroscopic measurements were made to try to understand this behavior. It was concluded that residual compressive stress due to transformation at the crack tip was responsible for the lower crack growth rates of the unstable 301 alloy. Cold worked specimens had significantly lower crack growth rates than the annealed specimens, and both alloys behaved identically.

  10. Fabrication of deuterium-loaded fiber Bragg grating and its spectral characteristics in thermal annealing

    Science.gov (United States)

    Shih, MingChang; Wang, C. C.; Yu, Cheng-Tsang; Chuang, Tung J.

    2000-07-01

    Previous results showed that the non-reversible (hystersis loop) of Bragg wave length shifting in thermal cycling of the Fiber Bragg Grating which is a high germanium doped optical fiber and high pressure hydrogen loaded was due to the diffusion out of the H2 residue in thermal annealing. In addition, the O-H absorption peak (1.38nm) causes signal attenuation and stability problem in FBG applications. We demonstrated up to 250 degree(s) C. The spectrum characteristics of the D2 loaded FBG compared to the H2 loaded FBG is presented. In general, (Delta) (Lambda) B of the D2 loaded FBG is narrower than H2 loaded, and (Lambda) B of the D2 loaded FBG is more stable than H2 loaded in thermal annealing. A model base on the UV photo-induced index change in the BFG core with D2 and H2 loaded to explain the spectrum characteristics between D2 and H2 loaded FBG is discussed.

  11. Solving Set Cover with Pairs Problem using Quantum Annealing

    Science.gov (United States)

    Cao, Yudong; Jiang, Shuxian; Perouli, Debbie; Kais, Sabre

    2016-09-01

    Here we consider using quantum annealing to solve Set Cover with Pairs (SCP), an NP-hard combinatorial optimization problem that plays an important role in networking, computational biology, and biochemistry. We show an explicit construction of Ising Hamiltonians whose ground states encode the solution of SCP instances. We numerically simulate the time-dependent Schrödinger equation in order to test the performance of quantum annealing for random instances and compare with that of simulated annealing. We also discuss explicit embedding strategies for realizing our Hamiltonian construction on the D-wave type restricted Ising Hamiltonian based on Chimera graphs. Our embedding on the Chimera graph preserves the structure of the original SCP instance and in particular, the embedding for general complete bipartite graphs and logical disjunctions may be of broader use than that the specific problem we deal with.

  12. Thermally induced native defect transform in annealed GaSb

    Science.gov (United States)

    Jie, Su; Tong, Liu; Jing-Ming, Liu; Jun, Yang; Yong-Biao, Bai; Gui-Ying, Shen; Zhi-Yuan, Dong; Fang-Fang, Wang; You-Wen, Zhao

    2016-07-01

    Undoped p-type GaSb single crystals were annealed at 550-600 °C for 100 h in ambient antimony. The annealed GaSb samples were investigated by Hall effect measurement, glow discharge mass spectroscopy (GDMS), infrared (IR) optical transmission and photoluminescence (PL) spectroscopy. Compared with the as-grown GaSb single crystal, the annealed GaSb samples have lower hole concentrations and weak native acceptor related PL peaks, indicating the reduction of the concentration of gallium antisite related native acceptor defects. Consequently, the below gap infrared transmission of the GaSb samples is enhanced after the thermal treatment. The mechanism about the reduction of the native defect concentration and its influence on the material property were discussed. Project supported by the National Natural Science Foundation of China (Grant Nos. 61474104 and 61504131).

  13. Reduction of Annealing Times for Energy Conservation in Aluminum

    Energy Technology Data Exchange (ETDEWEB)

    Anthony D. Rollett; Hasso Weiland; Mohammed Alvi; Abhijit Brahme

    2005-08-31

    Carnegie Mellon University was teamed with the Alcoa Technical Center with support from the US Dept. of Energy (Office of Industrial Technology) and the Pennsylvania Technology Investment Authority (PTIA) to make processing of aluminum less costly and more energy efficient. Researchers in the Department of Materials Science and Engineering have investigated how annealing processes in the early stages of aluminum processing affect the structure and properties of the material. Annealing at high temperatures consumes significant amounts of time and energy. By making detailed measurements of the crystallography and morphology of internal structural changes they have generated new information that will provide a scientific basis for shortening processing times and consuming less energy during annealing.

  14. Microstructural evolution of aluminum alloy 3003 during annealing

    Institute of Scientific and Technical Information of China (English)

    WU Wen-xiang; ZHANG Xin-ming; SUN De-qin; HU Guo-qiang; LIU Guo-jin

    2006-01-01

    The microstructural evolution of cold-rolled aluminum alloy 3003 during annealing was investigated by means of micro-hardness measurement, electrical resistivity measurement, optical microscopy and transmission electron microscopy. The interaction of recrystallization and precipitation of aluminum alloy 3003 was also discussed. The results show that the recrystallized grain size of cold-rolled aluminum alloy 3003 is strongly affected by precipitation during annealing. When precipitation occurs prior to recrystallization at low temperature(300 ℃), the grain structure becomes coarse, and the precipitation process is affected by the presence of lattice defects, i.e. high cold reduction results in a large number of precipitates. When annealing at 500 ℃, however, for the recrystallization is prior to precipitation, the precipitation is independent of cold deformation reduction and a fine, equiaxed grain structure is obtained.

  15. Five-fold twin formation during annealing of nanocrystalline Cu

    Energy Technology Data Exchange (ETDEWEB)

    Bringa, E M; Farkas, D; Caro, A; Wang, Y M; McNaney, J; Smith, R

    2009-05-20

    Contrary to the common belief that many-fold twins, or star twins, in nanophase materials are due to the action of significant external stresses, we report molecular dynamics simulations of annealing in 5 nm grain size samples annealed at 800 K for nearly 0.5 nsec at 0 external pressure showing the formation of five-fold star twins during annealing under the action of the large internal stresses responsible for grain growth and microstructural evolution. The structure of the many-fold twins is remarkably similar to those we have found to occur under uniaxial shock loading, of samples of nanocrystalline NiW with a grain size of {approx}5-30 nm. The mechanism of formation of the many-fold twins is discussed in the light of the simulations and experiments.

  16. Structure evolution on annealing of copper-doped carbon film

    Energy Technology Data Exchange (ETDEWEB)

    Onoprienko, A.A. [Frantsevich Institute for Problems of Materials Science, National Academy of Sciences of Ukraine, 3 Krzhyzhanovsky St., 03142 Kiev (Ukraine)]. E-mail: onopr@ipms.kiev.ua; Danilenko, N.I. [Frantsevich Institute for Problems of Materials Science, National Academy of Sciences of Ukraine, 3 Krzhyzhanovsky St., 03142 Kiev (Ukraine); Kossko, I.A. [Frantsevich Institute for Problems of Materials Science, National Academy of Sciences of Ukraine, 3 Krzhyzhanovsky St., 03142 Kiev (Ukraine)

    2007-06-13

    Thin copper-doped (8 at.% Cu) carbon film was deposited by direct current magnetron sputtering of composite graphite/copper target in argon plasma. The evolution of film structure on annealing at 600 deg. C in a vacuum has been studied by transmission electron microscopy and electron diffraction. The as-deposited film was amorphous with copper atoms uniformly distributed over the film volume. Annealing resulted in precipitation of copper particles within carbon film followed by the decrease in the density of copper particles and increase in particle average size with annealing time due to diffusion coalescence within the ensemble of copper particles. The coalescence occurred by the mixed mechanism of bulk and surface diffusion of copper atoms within carbon film that contained a large number of structural defects. As a result, the mean radius of copper particles in ensemble changed as R-bar {sup 5} {approx} t.

  17. NRC assessment of the Department of Energy annealing demonstration project

    Energy Technology Data Exchange (ETDEWEB)

    Jackson, D.A.; Malik, S.N. [Nuclear Regulatory Commission, Washington, DC (United States)

    1997-02-01

    Thermal annealing is the only known method for mitigating the effects of neutron irradiation embrittlement in reactor pressure vessel (RPV) steels. In May 1996, the US Department of Energy (DOE) in conjunction with the American Society of Mechanical Engineers, Westinghouse, Cooperheat, Electric Power Research Institute (with participating utilities), Westinghouse Owner`s Group, Consumers Power, Electricite` de France, Duquesne Light and the Central Research Institute of the Electric Power Industry (Japan) sponsored an annealing demonstration project (ADP) at Marble Hill. The Marble Hill Plant, located in Madison, Indiana, is a Westinghouse 4 loop design. The plant was nearly 70% completed when the project was canceled. Hence, the RPV was never irradiated. The paper will present highlights from the NRCs independent evaluation of the Marble Hill Annealing Demonstration Project.

  18. A flexible annealing chaotic neural network to maximum clique problem.

    Science.gov (United States)

    Yang, Gang; Tang, Zheng; Zhang, Zhiqiang; Zhu, Yunyi

    2007-06-01

    Based on the analysis and comparison of several annealing strategies, we present a flexible annealing chaotic neural network which has flexible controlling ability and quick convergence rate to optimization problem. The proposed network has rich and adjustable chaotic dynamics at the beginning, and then can converge quickly to stable states. We test the network on the maximum clique problem by some graphs of the DIMACS clique instances, p-random and k random graphs. The simulations show that the flexible annealing chaotic neural network can get satisfactory solutions at very little time and few steps. The comparison between our proposed network and other chaotic neural networks denotes that the proposed network has superior executive efficiency and better ability to get optimal or near-optimal solution.

  19. SIMULATED ANNEALING BASED POLYNOMIAL TIME QOS ROUTING ALGORITHM FOR MANETS

    Institute of Scientific and Technical Information of China (English)

    Liu Lianggui; Feng Guangzeng

    2006-01-01

    Multi-constrained Quality-of-Service (QoS) routing is a big challenge for Mobile Ad hoc Networks (MANETs) where the topology may change constantly. In this paper a novel QoS Routing Algorithm based on Simulated Annealing (SA_RA) is proposed. This algorithm first uses an energy function to translate multiple QoS weights into a single mixed metric and then seeks to find a feasible path by simulated annealing. The paper outlines simulated annealing algorithm and analyzes the problems met when we apply it to Qos Routing (QoSR) in MANETs. Theoretical analysis and experiment results demonstrate that the proposed method is an effective approximation algorithms showing better performance than the other pertinent algorithm in seeking the (approximate) optimal configuration within a period of polynomial time.

  20. A Personified Annealing Algorithm for Circles Packing Problem

    Institute of Scientific and Technical Information of China (English)

    ZHANGDe-Fu; LIXin

    2005-01-01

    Circles packing problem is an NP-hard problem and is difficult to solve. In this paper, a hybrid search strategy for circles packing problem is discussed. A way of generating new configuration is presented by simulating the moving of elastic objects, which can avoid the blindness of simulated annealing search and make iteration process converge fast. Inspired by the life experiences of people,an effective personified strategy to jump out of local minima is given. Based on the simulated annealing idea and personification strategy, an effective personified annealing algorithm for circles packing problem is developed. Numerical experiments on benchmark problem instances show that the proposed algorithm outperforms the best algorithm in the literature.

  1. Incoherent-light-flash annealing of phosphorus-implanted silicon

    Science.gov (United States)

    Correra, L.; Pedulli, L.

    1980-07-01

    Incoherent light pulses emitted from a xenon flash lamp were used to anneal radiation damage in (100) silicon implanted with 2×1015 31P+/cm2 at 100 keV. Electrical carrier concentration has been determined by means of differential sheet resistivity and Hall effect together with the anodic oxidation stripping technique; the surface photovoltage technique has been used to evaluate bulk lifetime and Rutherford backscattering and transmission electron microscopy for analysis of radiation damage. Damage recovery appears to take place via a solid phase epitaxial process. Electrical activity and carrier mobility values of samples annealed by incoherent light are similar to those obtained by laser, electron beam, and furnace annealing. The bulk lifetime of minority carriers is not degraded.

  2. Coordination Hydrothermal Interconnection Java-Bali Using Simulated Annealing

    Science.gov (United States)

    Wicaksono, B.; Abdullah, A. G.; Saputra, W. S.

    2016-04-01

    Hydrothermal power plant coordination aims to minimize the total cost of operating system that is represented by fuel costand constraints during optimization. To perform the optimization, there are several methods that can be used. Simulated Annealing (SA) is a method that can be used to solve the optimization problems. This method was inspired by annealing or cooling process in the manufacture of materials composed of crystals. The basic principle of hydrothermal power plant coordination includes the use of hydro power plants to support basic load while thermal power plants were used to support the remaining load. This study used two hydro power plant units and six thermal power plant units with 25 buses by calculating transmission losses and considering power limits in each power plant unit aided by MATLAB software during the process. Hydrothermal power plant coordination using simulated annealing plants showed that a total cost of generation for 24 hours is 13,288,508.01.

  3. Chaotic Multiquenching Annealing Applied to the Protein Folding Problem

    Science.gov (United States)

    Liñan-García, Ernesto; Sánchez-Pérez, Mishael; Sánchez-Hernández, Juan Paulo

    2014-01-01

    The Chaotic Multiquenching Annealing algorithm (CMQA) is proposed. CMQA is a new algorithm, which is applied to protein folding problem (PFP). This algorithm is divided into three phases: (i) multiquenching phase (MQP), (ii) annealing phase (AP), and (iii) dynamical equilibrium phase (DEP). MQP enforces several stages of quick quenching processes that include chaotic functions. The chaotic functions can increase the exploration potential of solutions space of PFP. AP phase implements a simulated annealing algorithm (SA) with an exponential cooling function. MQP and AP are delimited by different ranges of temperatures; MQP is applied for a range of temperatures which goes from extremely high values to very high values; AP searches for solutions in a range of temperatures from high values to extremely low values. DEP phase finds the equilibrium in a dynamic way by applying least squares method. CMQA is tested with several instances of PFP. PMID:24790563

  4. Enhancement of GMI Effect in Silicon Steels by Furnace Annealing

    Institute of Scientific and Technical Information of China (English)

    C.Sirisathitkul; P. Jantaratana

    2009-01-01

    The ratio and sensitivity of giant magnetoimpedance (GMI) in grain oriented silicon steels (Fe-4.5%Si) are improved after furnace annealing in air for 20 min. By annealing at 800℃, the GMI sensitivity rises from 1.29%/Oe to 1.91%/Oe and the ratio increases from 237% to 294% with decreasing characteristic frequency. The results are attributable to an increase in the transverse magnetic permeability during the heat treatment. From simulation by finite element method, the GMI effect can be interpreted as the modification of the current distribution by the applied magnetic field via the transverse permeability. In the case of annealed samples, the larger transverse permeability allows a higher GMI ratio and sensitivity.

  5. Annealing behavior of rolled AZ31 alloy sheet

    Institute of Scientific and Technical Information of China (English)

    PENG Wei-ping; LI Pei-jie; ZENG Pan

    2006-01-01

    The annealed microstructures of the rolled AZ31 alloy sheets were examined by using light optical microscopy. The mechanical properties were measured by tensile testing, with their crystal orientations analyzed by X-ray diffraction (XRD). After the annealing treatment, the elongated grains were transformed to equiaxed grains with uniform and homogeneous structures. The changes of microstructure decreased the yield strength and enhanced the elongation. The analysis of XRD shows that the AZ31 alloy sheet possesses intense basal-texture, which is weakened during the recrystallization while reinforced during the grain growth. The intense basal-texture induces low ductility, which hence makes the further rolling more difficult. The results indicate that the optimum annealing treatment during AZ31 alloys sheet rolling is at about 300 ℃ for 60-120 min.

  6. Phosphorus diffusion in germanium following implantation and excimer laser annealing

    Science.gov (United States)

    Wang, Chen; Li, Cheng; Huang, Shihao; Lu, Weifang; Yan, Guangming; Zhang, Maotian; Wu, Huanda; Lin, Guangyang; Wei, Jiangbin; Huang, Wei; Lai, Hongkai; Chen, Songyan

    2014-05-01

    We focus our study on phosphorus diffusion in ion-implanted germanium after excimer laser annealing (ELA). An analytical model of laser annealing process is developed to predict the temperature profile and the melted depth in Ge. Based on the heat calculation of ELA, a phosphorus diffusion model has been proposed to predict the dopant profiles in Ge after ELA and fit SIMS profiles perfectly. A comparison between the current-voltage characteristics of Ge n+/p junctions formed by ELA at 250 mJ/cm2 and rapid thermal annealing at 650 °C for 15 s has been made, suggesting that ELA is promising for high performance Ge n+/p junctions.

  7. Annealing Effect on Photovoltages of Quartz Single Crystals

    Institute of Scientific and Technical Information of China (English)

    TIAN Lu; ZHAO Song-Qing; ZHAO Kun

    2010-01-01

    @@ We investigate the photovoltaic effects of quartz single crystals annealed at high temperatures in ambient atmosphere.The open-circuit photovoltages and surface morphologies strongly depend on the heating treatments.When the annealing temperature increases from room temperature to 900℃,the rms roughness of quartz single crystal wafers increases from 0.207 to 1.011 nm.In addition,the photovoltages decrease from 1.994#V at room temperature to 1.551 μ V after treated at 500℃,and then increase up to 9.8μV after annealed at 900℃.The inner mechanism of the present photovoltaic response and surface morphologies is discussed.

  8. Toward understanding dynamic annealing processes in irradiated ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Myers, Michael Thomas [Texas A & M Univ., College Station, TX (United States)

    2013-05-01

    High energy particle irradiation inevitably generates defects in solids. The ballistic formation and thermalization of the defect creation process occur rapidly, and are believed to be reasonably well understood. However, knowledge of the evolution of defects after damage cascade thermalization, referred to as dynamic annealing, is quite limited. Unraveling the mechanisms associated with dynamic annealing is crucial since such processes play an important role in the formation of stable postirradiation disorder in ion-beam-processing of semiconductors, and determines the “radiation tolerance” of many nuclear materials. The purpose of this dissertation is to further our understanding of the processes involved in dynamic annealing. In order to achieve this, two main tasks are undertaken.

  9. Molecular dynamics simulation of annealed ZnO surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Min, Tjun Kit; Yoon, Tiem Leong [School of Physics, Universiti Sains Malaysia, 11800 USM, Penang (Malaysia); Lim, Thong Leng [Faculty of Engineering and Technology, Multimedia University, Melaka Campus, 75450 Melaka (Malaysia)

    2015-04-24

    The effect of thermally annealing a slab of wurtzite ZnO, terminated by two surfaces, (0001) (which is oxygen-terminated) and (0001{sup ¯}) (which is Zn-terminated), is investigated via molecular dynamics simulation by using reactive force field (ReaxFF). We found that upon heating beyond a threshold temperature of ∼700 K, surface oxygen atoms begin to sublimate from the (0001) surface. The ratio of oxygen leaving the surface at a given temperature increases as the heating temperature increases. A range of phenomena occurring at the atomic level on the (0001) surface has also been explored, such as formation of oxygen dimers on the surface and evolution of partial charge distribution in the slab during the annealing process. It was found that the partial charge distribution as a function of the depth from the surface undergoes a qualitative change when the annealing temperature is above the threshold temperature.

  10. Chaotic Multiquenching Annealing Applied to the Protein Folding Problem

    Directory of Open Access Journals (Sweden)

    Juan Frausto-Solis

    2014-01-01

    Full Text Available The Chaotic Multiquenching Annealing algorithm (CMQA is proposed. CMQA is a new algorithm, which is applied to protein folding problem (PFP. This algorithm is divided into three phases: (i multiquenching phase (MQP, (ii annealing phase (AP, and (iii dynamical equilibrium phase (DEP. MQP enforces several stages of quick quenching processes that include chaotic functions. The chaotic functions can increase the exploration potential of solutions space of PFP. AP phase implements a simulated annealing algorithm (SA with an exponential cooling function. MQP and AP are delimited by different ranges of temperatures; MQP is applied for a range of temperatures which goes from extremely high values to very high values; AP searches for solutions in a range of temperatures from high values to extremely low values. DEP phase finds the equilibrium in a dynamic way by applying least squares method. CMQA is tested with several instances of PFP.

  11. Effect of Annealing on Rare Earth Based Hydrogen Storage Alloys

    Institute of Scientific and Technical Information of China (English)

    Li Jinhua

    2004-01-01

    Rare earth-based hydrogen storage alloy used as negative electrode materials for nickel-metal hydride (Ni-MH) batteries are used commercially.The effect of annealing treatment with different annealing temperature and time on the MLNi3.68 Co0.78 Mn0.35 Al0.27 and MMNi3.55 Co0.75 Mn0.40 Al0.30 alloys were investigated.The crystal microstructure,pressure-composition-isotherms (p-C-T) and electrochemical properties of alloys were examined by X-ray diffraction (XRD), automatic PCI monitoring system and electrical performance testing instruments.The optimum annealing treatment conditions of two kinds of alloys were determined.

  12. Thermal Cycle Annealing and its Application to Arsenic-Ion Implanted HgCdTe

    Science.gov (United States)

    2014-06-26

    doping profile, as shown in Figure 3. The TCA treatment on the unimplanted epilayers showed an exponential defect reduction proportional to the...Chamonal, P. Castelein, J. Zanatta, M. Tchagaspanian, A. Papon, J. Barnes, F. Henry, S. Gout , G. Bourgeois, C. Pautet and P. Fougeres, "HgCdTe FPAs

  13. Thermal annealing of K(+)-Na(+) ion-exchanged waveguides.

    Science.gov (United States)

    Giorgetti, E; Grando, D; Palchetti, L; Sottini, S

    1995-06-15

    The process of thermal annealing of K(+)(-)Na(+) ion-exchanged waveguides in soda lime glass is characterized and compared with a simple theoretical model. The discrepancies between theory and experiments in the case of initially thick guides disappear if the existence of a stress-induced contribution to the refractive index is assumed that is not proportional to the concentration of the doping ions. The results obtained for initially thin guides are exploited for the design of annealed single-mode channel waveguides: 0.4-dB coupling losses with commercial single-mode fibers at lambda = 1.321 microm were measured.

  14. Electron trap annealing in neutron transmutation doped silicon

    DEFF Research Database (Denmark)

    Guldberg, J.

    1977-01-01

    Silicon doped by neutron transmutation to 1.2×1014 phosphorus atoms/cm3 was investigated with deep level transient spectroscopy using evaporated Au/n-Si diodes. Seven bulk electron traps were identified which appear after 30 min N2 anneal at temperatures between 425 and 725 °C. Five of these anne......Silicon doped by neutron transmutation to 1.2×1014 phosphorus atoms/cm3 was investigated with deep level transient spectroscopy using evaporated Au/n-Si diodes. Seven bulk electron traps were identified which appear after 30 min N2 anneal at temperatures between 425 and 725 °C. Five...

  15. Population Annealing: Theory and Application in Spin Glasses

    Science.gov (United States)

    Machta, Jonathan; Wang, Wenlong; Katzgraber, Helmut G.

    Population annealing is an efficient sequential Monte Carlo algorithm for simulating equilibrium states of systems with rough free energy landscapes. The theory of population annealing is presented, and systematic and statistical errors are discussed. The behavior of the algorithm is studied in the context of large-scale simulations of the three-dimensional Ising spin glass and the performance of the algorithm is compared to parallel tempering. It is found that the two algorithms are similar in efficiency though with different strengths and weaknesses. Supported by NSF DMR-1151387, DMR-1208046 and DMR-1507506.

  16. Coplanar waveguide flux qubit suitable for quantum annealing

    Science.gov (United States)

    Quintana, Chris; Chen, Yu; Sank, D.; Kafri, D.; Megrant, A.; White, T. C.; Shabani, A.; Barends, R.; Campbell, B.; Chen, Z.; Chiaro, B.; Dunsworth, A.; Fowler, A.; Jeffrey, E.; Kelly, J.; Lucero, E.; Mutus, J. Y.; Neeley, M.; Neill, C.; O'Malley, P. J. J.; Roushan, P.; Vainsencher, A.; Wenner, J.; Martinis, J. M.

    We introduce the ''fluxmon'' flux qubit, designed with the goal of practical quantum annealing. The qubit's capacitance and linear inductance are provided by a coplanar waveguide on a low loss substrate, minimizing dielectric dissipation and in principle allowing for GHz-scale inter-qubit coupling in a highly connected tunable architecture. Utilizing a dispersive microwave readout scheme, we characterize single-qubit noise and dissipation, and present a simple tunable inter-qubit coupler. We discuss tradeoffs between coherence and coupling in a quantum annealing architecture. This work was supported by Google Inc. and by the NSF GRFP.

  17. Magnetoimpedance effect in current annealed Co-based amorphous wires

    Science.gov (United States)

    Ghanaatshoar, M.; Tehranchi, M. M.; Mohseni, S. M.; Parhizkari, M.; Roozmeh, S. E.; Jazayeri Gharehbagh, A.

    2006-09-01

    Current-annealing of Co68.15Fe4.35Si12.5B15 amorphous wires has been studied at various vacuum orders. Structure-sensitive properties such as the electrical resistance during Joule heating treatment have been monitored to investigate the structural changes. Different driving currents have been flowed through the samples at different vacuums between 6×10-2 and 6×10-5 mbar. Regarding the giant magnetoimpedance (GMI) effect, annealing at different vacuums but with the same current can lead to various responses.

  18. Adiabatic quantum computation and quantum annealing theory and practice

    CERN Document Server

    McGeoch, Catherine C

    2014-01-01

    Adiabatic quantum computation (AQC) is an alternative to the better-known gate model of quantum computation. The two models are polynomially equivalent, but otherwise quite dissimilar: one property that distinguishes AQC from the gate model is its analog nature. Quantum annealing (QA) describes a type of heuristic search algorithm that can be implemented to run in the ``native instruction set'''' of an AQC platform. D-Wave Systems Inc. manufactures {quantum annealing processor chips} that exploit quantum properties to realize QA computations in hardware. The chips form the centerpiece of a nov

  19. A theoretical comparison of evolutionary algorithms and simulated annealing

    Energy Technology Data Exchange (ETDEWEB)

    Hart, W.E.

    1995-08-28

    This paper theoretically compares the performance of simulated annealing and evolutionary algorithms. Our main result is that under mild conditions a wide variety of evolutionary algorithms can be shown to have greater performance than simulated annealing after a sufficiently large number of function evaluations. This class of EAs includes variants of evolutionary strategie and evolutionary programming, the canonical genetic algorithm, as well as a variety of genetic algorithms that have been applied to combinatorial optimization problems. The proof of this result is based on a performance analysis of a very general class of stochastic optimization algorithms, which has implications for the performance of a variety of other optimization algorithm.

  20. An Adaptive Filtering Algorithm using Mean Field Annealing Techniques

    OpenAIRE

    Persson, Per; Nordebo, Sven; Claesson, Ingvar

    2002-01-01

    We present a new approach to discrete adaptive filtering based on the mean field annealing algorithm. The main idea is to find the discrete filter vector that minimizes the matrix form of the Wiener-Hopf equations in a least-squares sense by a generalized mean field annealing algorithm. It is indicated by simulations that this approach, with complexity O(M^2) where M is the filter length, finds a solution comparable to the one obtained by the recursive least squares (RLS) algorithm but withou...

  1. A Quantum Annealing Computer Team Addresses Climate Change Predictability

    Science.gov (United States)

    Halem, M. (Principal Investigator); LeMoigne, J.; Dorband, J.; Lomonaco, S.; Yesha, Ya.; Simpson, D.; Clune, T.; Pelissier, C.; Nearing, G.; Gentine, P.; Fang, B.; Shehab, A.; Radov, Asen; Tikak, N.; Prouty, Roy; Harrison, Kenneth

    2016-01-01

    The near confluence of the successful launch of the Orbiting Carbon Observatory2 on July 2, 2014 and the acceptance on August 20, 2015 by Google, NASA Ames Research Center and USRA of a 1152 qubit D-Wave 2X Quantum Annealing Computer (QAC), offered an exceptional opportunity to explore the potential of this technology to address the scientific prediction of global annual carbon uptake by land surface processes. At UMBC,we have collected and processed 20 months of global Level 2 light CO2 data as well as fluorescence data. In addition we have collected ARM data at 2sites in the US and Ameriflux data at more than 20 stations. J. Dorband has developed and implemented a multi-hidden layer Boltzmann Machine (BM) algorithm on the QAC. Employing the BM, we are calculating CO2 fluxes by training collocated OCO-2 level 2 CO2 data with ARM ground station tower data to infer to infer measured CO2 flux data. We generate CO2 fluxes with a regression analysis using these BM derived weights on the level 2 CO2 data for three Ameriflux sites distinct from the ARM stations. P. Gentine has negotiated for the access of K34 Ameriflux data in the Amazon and is applying a neural net to infer the CO2 fluxes. N. Talik validated the accuracy of the BM performance on the QAC against a restricted BM implementation on the IBM Softlayer Cloud with the Nvidia co-processors utilizing the same data sets. G. Nearing and K. Harrison have extended the GSFC LIS model with the NCAR Noah photosynthetic parameterization and have run a 10 year global prediction of the net ecosystem exchange. C. Pellisier is preparing a BM implementation of the Kalman filter data assimilation of CO2 fluxes. At UMBC, R. Prouty is conducting OSSE experiments with the LISNoah model on the IBM iDataPlex to simulate the impact of CO2 fluxes to improve the prediction of global annual carbon uptake. J. LeMoigne and D. Simpson have developed a neural net image registration system that will be used for MODIS ENVI and will be

  2. Post-Annealing Ex-Vessel Dosimetry at Loviisa 1 - AN International Exercise

    Science.gov (United States)

    Serén, Tom; Hógel, Josef; Voorbraak, Willem P.

    2003-06-01

    In order to improve the assessment of the post-annealing neutron exposure an ex-vessel (cavity) irradiation was carried out during cycle 22 (1998-99) at unit 1 of the Loviisa NPP (type VVER 440) in Finland. A dosimeter holder rack was designed and built by Škoda JS a.s., Czech Republic. Dosimeter sets were provided by VTT, Škoda and JRC/NRG Petten, the Netherlands. Some of the dosimeters were counted at Škoda and NRG Petten in addition to VTT. The large number of reactions used provided a good basis for spectrum adjustment. The results of the intercomparison are presented as well as a critical assessment of the materials and methods used. A similar irradiation is planned for Loviisa unit 2 during 2002-03.

  3. An Overview of Approaches to Modernize Quantum Annealing Using Local Searches

    Directory of Open Access Journals (Sweden)

    Nicholas Chancellor

    2016-06-01

    Full Text Available I describe how real quantum annealers may be used to perform local (in state space searches around specified states, rather than the global searches traditionally implemented in the quantum annealing algorithm. The quantum annealing algorithm is an analogue of simulated annealing, a classical numerical technique which is now obsolete. Hence, I explore strategies to use an annealer in a way which takes advantage of modern classical optimization algorithms, and additionally should be less sensitive to problem mis-specification then the traditional quantum annealing algorithm.

  4. Explanations of the unusual photoluminescence observed in annealed InGaN/GaN multi quantum well

    Energy Technology Data Exchange (ETDEWEB)

    Biswas, Dipankar, E-mail: diiibiswas@yahoo.co.in; Bera, Partha Pratim, E-mail: pratimpartha.bera@gmail.com; Mistry, Apu [Institute of Radiophysics and Eletronics,University of Calcutta, Kolkata (India)

    2015-05-15

    During growth and fabrication of devices, InGaN/GaN QWs undergo several thermal cyclings which causes redistribution of the elements, particularly In in the QW structures. This causes significant changes in the optical properties of the QWs. The thermal cyclings are often accompanied by alloy clustering and phase separation. So in order to have a deep knowledge of how the nano structures behave with thermal cyclings the process is simulated through successive annealing at high temperatures which are accompanied by photoluminescence (PL) measurements to obtain the optical properties at each stage. III-V nanostructures, in most usual cases, on annealing lead to a monotonic blue shift of the PL peak energy and goes into saturation. Recently there were reports in which the PL peak initially had a red shift which was followed by an increase in energy, a blue shift i.e. the PL peak goes through an inflexion. These unusual observations have been explained in this paper through quantum mechanical models and computations, which remained unexplained.

  5. Safe cycling!

    CERN Multimedia

    Anaïs Schaeffer

    2012-01-01

    The HSE Unit will be running a cycling safety campaign at the entrances to CERN's restaurants on 14, 15 and 16 May. Pop along to see if they can persuade you to get back in the saddle!   With summer on its way, you might feel like getting your bike out of winter storage. Well, the HSE Unit has come up with some original ideas to remind you of some of the most basic safety rules. This year, the prevention campaign will be focussing on three themes: "Cyclists and their equipment", "The bicycle on the road", and "Other road users". This is an opportunity to think about the condition of your bike as well as how you ride it. From 14 to 16 May, representatives of the Swiss Office of Accident Prevention and the Touring Club Suisse will join members of the HSE Unit at the entrances to CERN's restaurants to give you advice on safe cycling (see box). They will also be organising three activity stands where you can test your knowle...

  6. Interpretation of microstructure evolution during self-annealing and thermal annealing of nanocrystalline electrodeposits—A comparative study

    DEFF Research Database (Denmark)

    Pantleon, Karen; Somers, Marcel A. J.

    2010-01-01

    Electrodeposition results in a non-equilibrium state of the as-deposited nanocrystalline microstructure, which evolves towards an energetically more favorable state as a function of time and/or temperature upon deposition. Real-time investigation of the evolving microstructure in copper, silver......-annealing kinetics of copper and silver electrodeposits as well as the annealing kinetics of electrodeposited nickel. Similarities and characteristic differences of the kinetics and mechanisms of microstructure evolution in the various electrodeposits are discussed and the experimental results are attempted...

  7. Natural Gas Monthly, October 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-11-10

    The (NGM) Natural Gas Monthly highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. This month`s feature articles are: US Production of Natural Gas from Tight Reservoirs: and Expanding Rule of Underground Storage.

  8. Natural gas monthly, May 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-05-25

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. The featured articles for this month are: Opportunities with fuel cells, and revisions to monthly natural gas data.

  9. Monthly energy review, January 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-01-01

    This report presents an overview of recent monthly energy statistics. Major activities covered include production, consumption, trade, stocks, and prices for fossil fuels, electricity, and nuclear energy.

  10. Natural gas monthly, July 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. The feature article this month is entitled ``Intricate puzzle of oil and gas reserves growth.`` A special report is included on revisions to monthly natural gas data. 6 figs., 24 tabs.

  11. Monthly Program Cost Report (MPCR)

    Data.gov (United States)

    Department of Veterans Affairs — The Monthly Program Cost Report (MPCR) replaces the Cost Distribution Report (CDR). The MPCR provides summary information about Veterans Affairs operational costs,...

  12. In-situ Thermal Annealing of On-Membrane SOI Semiconductor-Based Devices After High Gamma Dose Irradiation.

    Science.gov (United States)

    Amor, Sedki; André, Nicolas; Kilchytska, Valeriya; Tounsi, Fares; Mezghani, Brahim; Gérard, Pierre; Ali, S Z; Udrea, Florin; Flandre, Denis; Francis, Laurent A

    2017-03-14

    In this paper, we investigate the recovery of some semiconductor-based components, such as N/P-type field-effect transistors (FETs) and a Complementary Metal-Oxide-Semiconductor (CMOS) inverter, after being exposed to a high total dose of gamma rays radiation. The employed method consists mainly in a rapid, low power and in-situ annealing mitigation technique by Silicon-On-Insulator (SOI) micro-hotplates. Due to the ionizing effect of the gamma irradiation, the threshold voltages showed an average shift of 580 mV for N-channel transistors, and -360 mV for P-MOSFETs. A 4 min double-cycles annealing of components with a temperature of the heater up to 465°C, corresponding to a maximum power of 38 mW, ensured a partial recovery but was not sufficient for a full recovery. The degradation has been completely recovered after the use of a built-in high temperature annealing process, up to 975 °C for 8 min corresponding to a maximum power of 112 mW, which restored the normal operating characteristics for all devices after their irradiation.

  13. Thermal annealing of protocrystalline a-Si:H

    NARCIS (Netherlands)

    Muller, T.F.G.; Arendse, C.J.; Halindintwali, S.; Knoesen, D.; Schropp, R.E.I.

    2011-01-01

    It proves difficult to obtain a set of protocrystalline silicon materials with different characteristics from the same deposition chamber to study the exact nature of these transition region materials. Hot-wire deposited protocrystalline silicon was thus isochronically annealed at different

  14. Electrochemically induced annealing of stainless-steel surfaces

    Science.gov (United States)

    Burstein, G. T.; Hutchings, I. M.; Sasaki, K.

    2000-10-01

    Modification of the surface properties of metals without affecting their bulk properties is of technological interest in demanding applications where surface stability and hardness are important. When austenitic stainless steel is heavily plastically deformed by grinding or rolling, a martensitic phase transformation occurs that causes significant changes in the bulk and surface mechanical properties of the alloy. This martensitic phase can also be generated in stainless-steel surfaces by cathodic charging, as a consequence of lattice strain generated by absorbed hydrogen. Heat treatment of the steel to temperatures of several hundred degrees can result in loss of the martensitic structure, but this alters the bulk properties of the alloy. Here we show that martensitic structures in stainless steel can be removed by appropriate electrochemical treatment in aqueous solutions at much lower temperature than conventional annealing treatments. This electrochemically induced annealing process allows the hardness of cold-worked stainless steels to be maintained, while eliminating the brittle martensitic phase from the surface. Using this approach, we are able to anneal the surface and near-surface regions of specimens that contain rolling-induced martensite throughout their bulk, as well as those containing surface martensite induced by grinding. Although the origin of the electrochemical annealing process still needs further clarification, we expect that this treatment will lead to further development in enhancing the surface properties of metals.

  15. EPR of ion-implanted, laser-annealed silicon

    Energy Technology Data Exchange (ETDEWEB)

    Brower, K.L.; Peercy, P.S.

    1979-01-01

    Electron paramagnetic resonance and ion backscattering measurements were made on ion-implanted, pulsed laser-annealed silicon. For phosphorus-implanted silicon (3 x 10/sup 13/ 200 keV P/sup +//cm/sup 2/) the electrical activity of the implanted donors is restored after laser annealing with greater than or equal to 1.8 J/cm/sup 2/. Silicon made amorphous with 2 x 10/sup 15/ 200 keV Si/sup +//cm/sup 2/ and implanted with 3 x 10/sup 13/ 200 keV P/sup +//cm/sup 2/ can be restored to crystallinity after laser annealing, but electrical activity of the P was not restored due to residual defects for laser energies less than or equal to 3 J/cm/sup 2/. Electrical activity can be restored, at least in part, for amorphous silicon implanted at lower energies (approx. = 50 keV). We also observed that N/sub 2/ reacts with amorphous silicon surfaces to form silicon-nitride. Under laser annealing the N is redistributed and exists as an N interstitial within the implanted layer.

  16. HAFNIUM IMPLANTED IN IRON .1. LATTICE LOCATION AND ANNEALING BEHAVIOR

    NARCIS (Netherlands)

    DEBAKKER, JMGJ; PLEITER, F; SMULDERS, PJM

    1993-01-01

    Perturbed angular correlation, Rutherford backscattering and channelling experiments were conducted to study the lattice location and annealing behaviour of 110 keV hafnium ions implanted into iron single crystals. It was found that a fraction of 11-25% of the implanted hafnium atoms are located at

  17. Hafnium implanted in iron 1. Lattice location and annealing behavior

    NARCIS (Netherlands)

    de Bakker, J.M.G.J.; Pleiter, F; Smulders, P.J M

    1993-01-01

    Perturbed angular correlation, Rutherford backscattering and channelling experiments were conducted to study the lattice location and annealing behaviour of 110 keV hafnium ions implanted into iron single crystals. It was found that a fraction of 11-25% of the implanted hafnium atoms are located at

  18. Annealing properties of potato starches with different degrees of phosphorylation

    DEFF Research Database (Denmark)

    Muhrbeck, Per; Svensson, E

    1996-01-01

    Changes in the gelatinization temperature interval and gelatinization enthalpy with annealing time at 50 degrees C were followed for a number of potato starch samples, with different degrees of phosphorylation, using differential scanning calorimetry. The gelatinization temperature increased with...... and crystalline structure of amylopectin helices. (C) 1997 Elsevier Science Ltd....

  19. Hafnium implanted in iron 1. Lattice location and annealing behavior

    NARCIS (Netherlands)

    de Bakker, J.M.G.J.; Pleiter, F; Smulders, P.J M

    1993-01-01

    Perturbed angular correlation, Rutherford backscattering and channelling experiments were conducted to study the lattice location and annealing behaviour of 110 keV hafnium ions implanted into iron single crystals. It was found that a fraction of 11-25% of the implanted hafnium atoms are located at

  20. Raman scattering from rapid thermally annealed tungsten silicide

    Science.gov (United States)

    Kumar, Sandeep; Dasgupta, Samhita; Jackson, Howard E.; Boyd, Joseph T.

    1987-01-01

    Raman scattering as a technique for studying the formation of tungsten silicide is presented. The tungsten silicide films have been formed by rapid thermal annealing of thin tungsten films sputter deposited on silicon substrates. The Raman data are interpreted by using data from resistivity measurements, Auger and Rutherford backscattering measurements, and scanning electron microscopy.

  1. Impacts of excimer laser annealing on Ge epilayer on Si

    Science.gov (United States)

    Huang, Zhiwei; Mao, Yichen; Yi, Xiaohui; Lin, Guangyang; Li, Cheng; Chen, Songyan; Huang, Wei; Wang, Jianyuan

    2017-02-01

    The impacts of excimer laser annealing on the crystallinity of Ge epilayers on Si substrate grown by low- and high-temperature two-step approach in an ultra-high vacuum chemical vapor deposition system were investigated. The samples were treated by excimer laser annealing (ELA) at various laser power densities with the temperature above the melting point of Ge, while below that of Si, resulting in effective reduction of point defects and dislocations in the Ge layer with smooth surface. The full-width at half-maximum (FWHM) of X-ray diffraction patterns of the low-temperature Ge epilayer decreases with the increase in laser power density, indicating the crystalline improvement and negligible effect of Ge-Si intermixing during ELA processes. The short laser pulse time and large cooling rate cause quick melting and recrystallization of Ge epilayer on Si in the non-thermal equilibrium process, rendering tensile strain in Ge epilayer as calculated quantitatively with thermal mismatch between Si and Ge. The FWHM of X-ray diffraction patterns is significantly reduced for the two-step grown samples after treated by a combination of ELA and conventional furnace thermal annealing, indicating that the crystalline of Ge epilayer is improved more effectively with pre- annealing by excimer laser.

  2. Computer simulation of laser annealing of a nanostructured surface

    NARCIS (Netherlands)

    Ivanov, D.; Marinov, I.; Gorbachev, Y.; Smirnov, A.; Krzhizhanovskaya, V.

    2010-01-01

    Laser annealing technology is used in mass production of new-generation semiconductor materials and nano-electronic devices like the MOS-based (metal-oxide-semiconductor) integrated circuits. Manufacturing sub-100 nm MOS devices demands application of ultra-shallow doping (junctions), which requires

  3. Meta-Modeling by Symbolic Regression and Pareto Simulated Annealing

    NARCIS (Netherlands)

    Stinstra, E.; Rennen, G.; Teeuwen, G.J.A.

    2006-01-01

    The subject of this paper is a new approach to Symbolic Regression.Other publications on Symbolic Regression use Genetic Programming.This paper describes an alternative method based on Pareto Simulated Annealing.Our method is based on linear regression for the estimation of constants.Interval arithm

  4. Self-Organization and Annealed Disorder in a Fracturing Process

    DEFF Research Database (Denmark)

    Caldarelli, Guido; Di Tolla, Francesco; Petri, Alberto

    1996-01-01

    We show that a vectorial model for inhomogeneous elastic media self-organizes under external stress. An onset of crack avalanches of every duration and length scale compatible with the lattice size is observed. The behavior is driven by the introduction of annealed disorder, i.e., by lowering the...

  5. A Deterministic Annealing Approach to Clustering AIRS Data

    Science.gov (United States)

    Guillaume, Alexandre; Braverman, Amy; Ruzmaikin, Alexander

    2012-01-01

    We will examine the validity of means and standard deviations as a basis for climate data products. We will explore the conditions under which these two simple statistics are inadequate summaries of the underlying empirical probability distributions by contrasting them with a nonparametric, method called Deterministic Annealing technique

  6. Thermally assisted quantum annealing of a 16-qubit problem.

    Science.gov (United States)

    Dickson, N G; Johnson, M W; Amin, M H; Harris, R; Altomare, F; Berkley, A J; Bunyk, P; Cai, J; Chapple, E M; Chavez, P; Cioata, F; Cirip, T; Debuen, P; Drew-Brook, M; Enderud, C; Gildert, S; Hamze, F; Hilton, J P; Hoskinson, E; Karimi, K; Ladizinsky, E; Ladizinsky, N; Lanting, T; Mahon, T; Neufeld, R; Oh, T; Perminov, I; Petroff, C; Przybysz, A; Rich, C; Spear, P; Tcaciuc, A; Thom, M C; Tolkacheva, E; Uchaikin, S; Wang, J; Wilson, A B; Merali, Z; Rose, G

    2013-01-01

    Efforts to develop useful quantum computers have been blocked primarily by environmental noise. Quantum annealing is a scheme of quantum computation that is predicted to be more robust against noise, because despite the thermal environment mixing the system's state in the energy basis, the system partially retains coherence in the computational basis, and hence is able to establish well-defined eigenstates. Here we examine the environment's effect on quantum annealing using 16 qubits of a superconducting quantum processor. For a problem instance with an isolated small-gap anticrossing between the lowest two energy levels, we experimentally demonstrate that, even with annealing times eight orders of magnitude longer than the predicted single-qubit decoherence time, the probabilities of performing a successful computation are similar to those expected for a fully coherent system. Moreover, for the problem studied, we show that quantum annealing can take advantage of a thermal environment to achieve a speedup factor of up to 1,000 over a closed system.

  7. Annealing effects of chemically synthesized FePt nanocrystal films

    Science.gov (United States)

    Hyun, Changbae; Lee, Doh C.

    2005-03-01

    Chemically synthesized FePt nanocrystals can exhibit room temperature ferromagnetism after being annealed at temperatures above ˜500^oC[1]. The thermal annealing changes the crystal structure from face-centered cubic to the hard magnetic face-centered tetragonal phase. In thick nanocrystal films, the coercivity can be quite large, however, the coercivity of thin films has been found to decrease significantly with decreasing thickness, even losing the room temperature ferromagnetism in some cases[2]. In order to help determine how the microscopic magnetic structure in these thin films evolves with film thickness, we studied using magnetic force microscopy (MFM), under external applied fields, films consisting of 4 to 15 nanocrystal monolayers. We cast smooth films of 4 nm diameter FePt nanocrystals and annealed them at temperatures ranging from 400 to 650^oC, acquiring MFM images as a function of annealing temperature. Thin FePt films showed lower coercivity than thick films. To help interpret the MFM images, complementary magnetic and structural data was obtained using SQUID magnetometry, x-ray diffraction, and transmission electron microscopy (TEM). [1] S. Sun et al., Science 287, 1989 (2000). [2] G. A. Held et al., Journal of Applied Physics 95, 1481 (2004)

  8. High temperature annealing studies of strontium ion implanted glassy carbon

    Energy Technology Data Exchange (ETDEWEB)

    Odutemowo, O.S., E-mail: u12052613@tuks.co.za [Department of Physics, University of Pretoria, Pretoria 0002 (South Africa); Malherbe, J.B.; Prinsloo, L.; Langa, D.F. [Department of Physics, University of Pretoria, Pretoria 0002 (South Africa); Wendler, E. [Institut für Festkörperphysik, Friedrich-Schiller University, Jena (Germany)

    2016-03-15

    Glassy carbon samples were implanted with 200 keV strontium ions to a fluence of 2 × 10{sup 16} ions/cm{sup 2} at room temperature. Analysis with Raman spectroscopy showed that ion bombardment amorphises the glassy carbon structure. Partial recovery of the glassy carbon structure was achieved after the implanted sample was vacuum annealed at 900 °C for 1 h. Annealing the strontium ion bombarded sample at 2000 °C for 5 h resulted in recovery of the glassy carbon substrate with the intensity of the D peak becoming lower than that of the pristine glassy carbon. Rutherford backscattering spectroscopy (RBS) showed that the implanted strontium diffused towards the surface of the glassy carbon after annealing the sample at 900 °C. This diffusion was also accompanied by loss of the implanted strontium. Comparison between the as-implanted and 900 °C depth profiles showed that less than 30% of the strontium was retained in the glassy carbon after heat treatment at 900 °C. The RBS profile after annealing at 2000 °C indicated that no strontium ions were retained after heat treatment at this temperature.

  9. Ball milling and annealing of Co-50 at% W Powders

    CSIR Research Space (South Africa)

    Bolokang, AS

    2013-04-01

    Full Text Available annealing of unmilled compacts yielded metastable phases. Upon 10 and 20 h ball milling of Co-W powder, no alloying was obtained. Although milling did not yield significant crystal changes in W and Co ground state struc- tures, its effect is evident during...

  10. Competitive annealing of multiple DNA origami: formation of chimeric origami

    Science.gov (United States)

    Majikes, Jacob M.; Nash, Jessica A.; LaBean, Thomas H.

    2016-11-01

    Scaffolded DNA origami are a robust tool for building discrete nanoscale objects at high yield. This strategy ensures, in the design process, that the desired nanostructure is the minimum free energy state for the designed set of DNA sequences. Despite aiming for the minimum free energy structure, the folding process which leads to that conformation is difficult to characterize, although it has been the subject of much research. In order to shed light on the molecular folding pathways, this study intentionally frustrates the folding process of these systems by simultaneously annealing the staple pools for multiple target or parent origami structures, forcing competition. A surprising result of these competitive, simultaneous anneals is the formation of chimeric DNA origami which inherit structural regions from both parent origami. By comparing the regions inherited from the parent origami, relative stability of substructures were compared. This allowed examination of the folding process with typical characterization techniques and materials. Anneal curves were then used as a means to rapidly generate a phase diagram of anticipated behavior as a function of staple excess and parent staple ratio. This initial study shows that competitive anneals provide an exciting way to create diverse new nanostructures and may be used to examine the relative stability of various structural motifs.

  11. Hydrogen permeability of Nb membrane annealed under ultra high vacuum

    Energy Technology Data Exchange (ETDEWEB)

    Uchida, Helmut T.; Pundt, Astrid; Kirchheim, Reiner [Institut fuer Materialphysik, Goettingen (Germany); Yamazaki, Yoshihiro [California Institute of Technology, California (United States); Kamegawa, Atsunori; Takamura, Hitoshi; Koike, Junichi; Okada, Masuo [Department of Materials Science, School of Engineering, Tohoku University, Sendai (Japan)

    2007-07-01

    In this research, hydrogen permeability of Pd-free Nb membrane using hydrogen annealing process by ultra high vacuum equipment was investigated. Pure Nb (99.85 percent) was used as membrane. The hydrogen permeation experiment was carried out in the temperature range of 773-1173 K, and the H{sub 2} pressure range of 1-3.5 atm in the inlet side. Hydrogen flux and hydrogen pressures in the inlet side and outlet side of chamber were measured using mass flow meter and capacitance manometer, respectively. Hydrogen permeability was determined by Fick's first low. Effects of annealing conditions and heat treatment under hydrogen atmosphere on hydrogen permeability were investigated. It is supposed that the surface oxidation of Nb is reduced by the hydrogen annealing. Moreover, it is found that the value of hydrogen permeability becomes almost equivalent to the theoretical value when the sample preparation was optimized by an extension of the evacuating time. The best hydrogen permeability is obtained in metal membranes using the annealing under ultra-high vacuum and pure hydrogen atmosphere.

  12. Thermal annealing of protocrystalline a-Si:H

    NARCIS (Netherlands)

    Muller, T.F.G.; Arendse, C.J.; Halindintwali, S.; Knoesen, D.; Schropp, R.E.I.

    2011-01-01

    It proves difficult to obtain a set of protocrystalline silicon materials with different characteristics from the same deposition chamber to study the exact nature of these transition region materials. Hot-wire deposited protocrystalline silicon was thus isochronically annealed at different temperat

  13. Deep level defects in high temperature annealed InP

    Institute of Scientific and Technical Information of China (English)

    DONG Zhiyuan; ZHAO Youwen; ZENG Yiping; DUAN Manlong; LIN Lanying

    2004-01-01

    Deep level defects in high temperature annealed semi-conducting InP have been studied by deep level transient spectroscopy (DLTS). There is obvious difference in the deep defects between as-grown InP, InP annealed in phosphorus ambient and iron phosphide ambient, as far as their quantity and concentration are concerned. Only two defects at 0.24 and 0.64 eV can be detected in InP annealed iniron phosphide ambient,while defects at 0.24, 0.42, 0.54 and 0.64 eV have been detected in InP annealed in phosphorus ambient, in contrast to two defects at 0.49 and 0.64 eV or one defect at 0.13eV in as-grown InP. A defect suppression phenomenon related to iron diffusion process has been observed. The formation mechanism and the nature of the defects have been discussed.

  14. High temperature annealing studies of strontium ion implanted glassy carbon

    Science.gov (United States)

    Odutemowo, O. S.; Malherbe, J. B.; Prinsloo, L.; Langa, D. F.; Wendler, E.

    2016-03-01

    Glassy carbon samples were implanted with 200 keV strontium ions to a fluence of 2 × 1016 ions/cm2 at room temperature. Analysis with Raman spectroscopy showed that ion bombardment amorphises the glassy carbon structure. Partial recovery of the glassy carbon structure was achieved after the implanted sample was vacuum annealed at 900 °C for 1 h. Annealing the strontium ion bombarded sample at 2000 °C for 5 h resulted in recovery of the glassy carbon substrate with the intensity of the D peak becoming lower than that of the pristine glassy carbon. Rutherford backscattering spectroscopy (RBS) showed that the implanted strontium diffused towards the surface of the glassy carbon after annealing the sample at 900 °C. This diffusion was also accompanied by loss of the implanted strontium. Comparison between the as-implanted and 900 °C depth profiles showed that less than 30% of the strontium was retained in the glassy carbon after heat treatment at 900 °C. The RBS profile after annealing at 2000 °C indicated that no strontium ions were retained after heat treatment at this temperature.

  15. Analysis of Trivium by a Simulated Annealing variant

    DEFF Research Database (Denmark)

    Borghoff, Julia; Knudsen, Lars Ramkilde; Matusiewicz, Krystian

    2010-01-01

    . A characteristic of equation systems that may be efficiently solvable by the means of such algorithms is provided. As an example, we investigate equation systems induced by the problem of recovering the internal state of the stream cipher Trivium. We propose an improved variant of the simulated annealing method...

  16. Annealing in sulfur of CZTS nanoparticles deposited through doctor blading

    DEFF Research Database (Denmark)

    Engberg, Sara Lena Josefin; Crovetto, Andrea

    ). A photovoltaic device of the structure soda lime glass (SLG)/Mo/CZTSSe/CdS/ZnO:Al/Ag has been built, and our preliminary results show a power conversion efficiency of 1.41% for the nanoparticles annealed in selenium. This work has been supported by a grant from the Danish Council for Strategic Research...

  17. The phase diagram of annealed Ge(111)/Ga

    DEFF Research Database (Denmark)

    Molinàs-Mata, P.; Böhringer, M.; Artacho, E.;

    1995-01-01

    A study of the annealed phases of Ge(111)/Ga for coverages above 0.05 ML is presented. The surfaces are investigated by low-energy electron diffraction, scanning tunneling microscopy, and partly by photoemission and surface X-ray diffraction using synchrotron radiation. For Ga coverages beyond 0....

  18. Annealing as grown large volume CZT single crystals increased spectral resolution

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Longxia Li

    2008-03-19

    would became un-dopant or 'intrinsic' with non radiation affection (we have studied before). We used 3 weeks annealing time for 3-5 mm thickness CZT wafres, if the thickness increased to 10-15mm, the annealing time would be increased to many months, which is very unpractical and very difficult to control the CZT property. We have obtained as-grown CZT by using adding the extra Cd before growth, which showed the smaller size of Te-precipitates and excellent radiation performance. These CZT has very high {micro}{tau}(e) >1 x 10{sup -2}cm{sup 2}/V, {rho} > 2 x 10{sup 10} {Omega}-cm, and the thickness could be up to 80-100mm. The energy resolution of the detector (thickness>10mm) at 662 keV is about 1.2% without any correction (2) and according to Aquila, the 0.5-0.8% resolution at 662 keV would be expected by using appropriated electronic correction.

  19. Toward understanding dynamic annealing processes in irradiated ceramics

    Science.gov (United States)

    Myers, Michael Thomas

    High energy particle irradiation inevitably generates defects in solids in the form of collision cascades. The ballistic formation and thermalization of cascades occur rapidly and are believed to be reasonably well understood. However, knowledge of the evolution of defects after damage cascade thermalization, referred to as dynamic annealing, is quite limited. Unraveling the mechanisms associated with dynamic an- nealing is crucial since such processes play an important role in the formation of stable post-irradiation disorder in ion-beam-processed semiconductors and determines the "radiation tolerance" of many nuclear materials. The purpose of this dissertation is to further our understanding of the processes involved in dynamic annealing. In order to achieve this, two main tasks are undertaken. First, the effects of dynamic annealing are investigated in ZnO, a technologically relevant material that exhibits very high dynamic defect annealing at room temper- ature. Such high dynamic annealing leads to unusual defect accumulation in heavy ion bombarded ZnO. Through this work, the puzzling features that were observed more than a decade ago in ion-channeling spectra have finally been explained. We show that the presence of a polar surface substantially alters damage accumulation. Non-polar surface terminations of ZnO are shown to exhibit enhanced dynamic an- nealing compared to polar surface terminated ZnO. Additionally, we demonstrate one method to reduce radiation damage in polar surface terminated ZnO by means of a surface modification. These results advance our efforts in the long-sought-after goal of understanding complex radiation damage processes in ceramics. Second, a pulsed-ion-beam method is developed and demonstrated in the case of Si as a prototypical non-metallic target. Such a method is shown to be a novel experimental technique for direct extraction of dynamic annealing parameters. The relaxation times and effective diffusion lengths of mobile defects

  20. Monthly energy review, November 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-11-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 37 figs., 61 tabs.

  1. Natural gas monthly, February 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. 6 figs., 28 tabs.

  2. Monthly energy review: April 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-04-01

    This monthly report presents an overview of energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. A section is also included on international energy. The feature paper which is included each month is entitled ``Energy equipment choices: Fuel costs and other determinants.`` 37 figs., 59 tabs.

  3. ULTRAPLATE 30 month management report

    DEFF Research Database (Denmark)

    Jensen, Jens Dahl

    2003-01-01

    In the period from month 24 to month 30 focus has been on the work-package 3 activities concerning optimisation of the newly developed ULTRAPLATE technology towards specific industrial applications. Three main application areas have been pursued: 1) High- speed plating of lead free solder contact...

  4. Your Baby's Growth: 5 Months

    Science.gov (United States)

    ... to Be Smart About Social Media Your Baby's Growth: 5 Months KidsHealth > For Parents > Your Baby's Growth: 5 Months Print A A A What's in ... your child's birth, the doctor has been recording growth in weight, length, and head size (circumference) during ...

  5. Monthly energy review, November 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 37 figs., 91 tabs.

  6. Natural gas monthly, November 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-11-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. 6 figs., 27 tabs.

  7. Natural gas monthly, January 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. 6 figs., 28 tabs.

  8. Monthly energy review, October 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-10-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 37 figs., 61 tabs.

  9. Monthly energy review, June 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 36 figs., 61 tabs.

  10. Monthly energy review, May 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 37 figs., 61 tabs.

  11. Monthly energy review, January 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-01-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 37 figs., 61 tabs.

  12. Monthly energy review, February 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 37 figs., 73 tabs.

  13. Monthly energy review, March 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 37 figs., 74 tabs.

  14. Natural gas monthly, December 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. 6 figs., 28 tabs.

  15. Left behind by Birth Month

    Science.gov (United States)

    Solli, Ingeborg Foldøy

    2017-01-01

    Utilizing comprehensive administrative data from Norway I investigate long-term birth month effects. I demonstrate that the oldest children in class have a substantially higher GPA than their younger peers. The birth month differences are larger for low-SES children. Furthermore, I find that the youngest children in class are lagging significantly…

  16. Monthly Energy Review, February 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-26

    This monthly publication presents an overview of EIA`s recent monthly energy statistics, covering the major activities of U.S. production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. Two brief descriptions (`energy plugs`) on two EIA publications are presented at the start.

  17. Haida Months of the Year.

    Science.gov (United States)

    Cogo, Robert

    Students are introduced to Haida vocabulary in this booklet which briefly describes the seasons and traditional seasonal activities of Southeastern Alaska Natives. The first section lists the months in English and Haida; e.g., January is "Taan Kungaay," or "Bear Hunting Month." The second section contains seasonal names in…

  18. Monthly energy review, November 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-11-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 75 tabs.

  19. Monthly energy review, July 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 37 figs. 73 tabs.

  20. Optical study of annealed cobalt–porous silicon nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Bouzourâa, M.-B. [Unité de Nanomatériaux et Photonique, Faculté des Sciences de Tunis, Département de Physique, 2092 El Manar, Tunis (Tunisia); Rahmani, M., E-mail: rahmanimehdi79@yahoo.com [Unité de Nanomatériaux et Photonique, Faculté des Sciences de Tunis, Département de Physique, 2092 El Manar, Tunis (Tunisia); Zaïbi, M.-A. [Unité de Nanomatériaux et Photonique, Faculté des Sciences de Tunis, Département de Physique, 2092 El Manar, Tunis (Tunisia); Ecole Supérieure des Sciences et Techniques de Tunis, 5 Avenue Taha Hussein, 1008 Tunis (Tunisia); Lorrain, N.; Hajji, L. [Université Européenne de Bretagne, CNRS FOTON-UMR 6082, 6 rue de Kérampont, BP 80518, 22305 Lannion, Cedex (France); Oueslati, M. [Unité de Nanomatériaux et Photonique, Faculté des Sciences de Tunis, Département de Physique, 2092 El Manar, Tunis (Tunisia)

    2013-11-15

    We report Raman and photoluminescence studies of cobalt–porous silicon nanocomposites (PS/Co). Cobalt was introduced in porous silicon (PS) by immersion method using CoCl{sub 2} aqueous solution. The presence of cobalt in PS matrix was identified by FTIR spectroscopy and EDX analyses. The Raman spectroscopy revealed the presence of Si bonded to cobalt oxide in PS/Co. We discuss also the Raman spectra of PS and PS/Co samples under different annealing temperatures ranging from room temperature (RT) to 600 °C. The optical properties of PS and PS/Co were studied by photoluminescence (PL). The highest PL intensity was observed for an immersion time of 60 min. For long duration, the deposited cobalt quantity acts as energy trap and promotes the non-radiative energy transfer; it is the autoextinction phenomenon. We have studied also the effect of the annealing temperature on the PL of both PS and PS/Co samples. For PS, the annealing process leads to a rapid oxidation of the Si nanocrystallites (nc-Si). In the case of PS/Co sample, two different mechanisms are proposed; one is the desorption of Si–H{sub x(x=2,3)} with the formation of cobalt oxide for annealing temperature less than 450 °C which causes the increasing of PL intensity and the stability of PL energy, the other mechanism is the transformation of the porous silicon to silica at high temperatures (≻450°C) which leads to the decreasing of the PL intensity and the blue shift of the PL curve. -- Highlights: • Introduction of cobalt ions into porous silicon (PS) layer using immersion method. • The Co ions influence the photoluminescence (PL) intensity of PS. • Annealing the PS/Co sample leads to an improvement of the PL intensity. • The increase of the PL is due to the formation of different cobalt oxides on the PS surface.

  1. Radiation and annealing response of WWER 440 beltline welding seams

    Science.gov (United States)

    Viehrig, Hans-Werner; Houska, Mario; Altstadt, Eberhard

    2015-01-01

    The focus of this paper is on the irradiation response and the effect of thermal annealing in weld materials extracted from decommissioned WWER 440 reactor pressure vessels of the nuclear power plant Greifswald. The characterisation is based on the measurement of the hardness, the yield stress, the Master Curve reference temperature, T0, and the Charpy-V transition temperature through the thickness of multi-layer beltline welding seams in the irradiated and the thermally annealed condition. Additionally, the weld bead structure was characterised by light microscopic studies. We observed a large variation in the through thickness T0 values in the irradiated as well as in thermally annealed condition. The T0 values measured with the T-S-oriented Charpy size SE(B) specimens cut from different thickness locations of the multilayer welding seams strongly depend on the intrinsic weld bead structure along the crack tip. The Master Curve, T0, and Charpy-V, TT47J, based ductile-to-brittle transition temperature progressions through the thickness of the multi-layer welding seam do not correspond to the forecast according to the Russian code. In general, the fracture toughness values at cleavage failure, KJc, measured on SE(B) specimens from the irradiated and large-scale thermally annealed beltline welding seams follow the Master Curve description, but more than the expected number lie outside the curves for 2% and 98% fracture probability. In this case the test standard ASTM E1921 indicates the investigated multi-layer weld metal as not uniform. The multi modal Master Curve based approach describes the temperature dependence of the specimen size adjusted KJc-1T values well. Thermal annealing at 475 °C for 152 h results in the expected decrease of the hardness and tensile strength and the shift of Master Curve and Charpy-V based ductile-to-brittle transition temperatures to lower values.

  2. MoO3 Thickness, Thermal Annealing and Solvent Annealing Effects on Inverted and Direct Polymer Photovoltaic Solar Cells

    Directory of Open Access Journals (Sweden)

    Guillaume Wantz

    2012-11-01

    Full Text Available Several parameters of the fabrication process of inverted polymer bulk heterojunction solar cells based on titanium oxide as an electron selective layer and molybdenum oxide as a hole selective layer were tested in order to achieve efficient organic photovoltaic solar cells. Thermal annealing treatment is a common process to achieve optimum morphology, but it proved to be damageable for the performance of this kind of inverted solar cells. We demonstrate using Auger analysis combined with argon etching that diffusion of species occurs from the MoO3/Ag top layers into the active layer upon thermal annealing. In order to achieve efficient devices, the morphology of the bulk heterojunction was then manipulated using the solvent annealing technique as an alternative to thermal annealing. The influence of the MoO3 thickness was studied on inverted, as well as direct, structure. It appeared that only 1 nm-thick MoO3 is enough to exhibit highly efficient devices (PCE = 3.8% and that increasing the thickness up to 15 nm does not change the device performance. 

  3. Discrepancy between ambient annealing and H{sup +} implantation in optical absorption of ZnO

    Energy Technology Data Exchange (ETDEWEB)

    Lv, Jinpeng, E-mail: hitljp@gmail.com [College of Astronautics, Nanjing University of Aeronautics and Astronautics, Nanjing, Jiangsu (China); Li, Chundong [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin, Heilongjiang (China)

    2016-05-15

    The discrepancy between sub-bandgap absorption in ZnO induced by thermal annealing and H{sup +} implantation is investigated in this study for the first time. Results indicate that nonreductive annealing-induced optical absorption is independent of annealing ambient, and can be assigned to V{sub O}, whereas the absorption centers caused by H{sup +} implantation and H{sub 2} annealing are primarily associated with V{sub O} and ionized Zn{sub i}.

  4. Process check of annealing process of coiled sheets by indirect measurement

    Directory of Open Access Journals (Sweden)

    K. Kostúr

    2017-01-01

    Full Text Available The contribution deals with a possibility of increasing quality production and decreasing costs in annealing furnaces by process check of annealing temperatures. The lowest temperature of annealed coiled sheets is very important. The information about this inner temperature is unknown during annealing. It is possible to obtain this information by indirect measurement. The indirect measurement uses two types of mathematical models. In this paper, the structure of both models and its verification is described.

  5. Effect of air annealing on structural and magnetic properties of Ni/NiO nanoparticles

    Science.gov (United States)

    Nadeem, K.; Ullah, Asmat; Mushtaq, M.; Kamran, M.; Hussain, S. S.; Mumtaz, M.

    2016-11-01

    We reported systematic study on structural and magnetic properties of nickel/nickel oxide (Ni/NiO) nanoparticles annealed under air atmosphere at different temperatures in the range 400-800 °C. The XRD spectra revealed two phases such as Ni and NiO. The average crystallite size increases with increasing annealing temperature. A phase diagram was developed between two phases versus annealing temperature using XRD analysis. At lower annealing temperatures, Ni phase is dominant which does not easily undergo oxidation to form NiO. The NiO phase increases with increasing annealing temperature. FTIR spectroscopy revealed an increase in the NiO phase content at higher annealing temperature, which is in agreement with the XRD analysis. SEM images showed that nanoparticles are well separated at lower annealing temperatures but get agglomerated at higher annealing temperatures. The ferromagnetic (FM) Ni phase content and saturation magnetization (Ms) showed nearly the same trend with increasing annealing temperature. The nanoparticles annealed at 500 °C and 800 °C revealed highest and lowest Ms values, respectively, which is in accordance with the XRD phase diagram. Coercivity showed an overall decreasing trend with increasing annealing temperature due to decreased concentration of FM Ni phase and increasing average crystallite size. All these measurements indicate that the structural and magnetic properties of Ni/NiO nanoparticles are strongly influenced by the annealing temperature.

  6. The effect of humidity on annealing of polymer optical fibre bragg gratings

    DEFF Research Database (Denmark)

    Woyessa, Getinet; Nielsen, Kristian; Bang, Ole

    2015-01-01

    The effect of humidity on annealing of PMMA based microstructured polymer optical fiber (mPOF) Bragg gratings is studied. Polymer optical fibers (POFs) are annealed in order to release stress formed during the fabrication process. Un-annealed fibers will have high hysteresis and low sensitivity...

  7. Influence of Microwave and Conventional Annealing Processes in Improving an Electrodeposited Nickel Interlayer Characteristics

    Science.gov (United States)

    Hassan, Abdelkarim; Noordin, Mohd Yusof; Izman, Sudin; Denni, Kurniawan

    2016-10-01

    Nickel interlayer was coated on tungsten carbide substrate by electrodeposition process for the purpose of diamond deposition. Conventional and microwave annealing processes were used to improve the adhesion strength and modify the surface composition of the electroplated nickel interlayer. The conventional annealing was conducted in a high-temperature tube furnace at 1323.15 K (1050 °C) for 20 and 60 minutes annealing durations. The microwave annealing was carried out in 2.45 GHz microwave furnace at 1303.15 K (1030 °C) for the same annealing durations as the conventional process. The annealed specimens were characterized by electron microscopy, Energy dispersive X-ray spectroscopy, and X-ray diffraction technique. Adhesion of the annealed nickel interlayer was assessed by the scratch test. The results revealed significant changes in the nickel coating composition, adhesion, and appearance. The adhesion strength of nickel interlayer annealed for the longer duration of the two processes is similar. For shorter annealing duration, the microwave-annealed coating showed better adhesion. The surface composition of the nickel interlayer was modified by the diffusion of carbon and tungsten during the microwave and conventional annealing, respectively. The microwave annealing is a promising process for producing good quality treated nickel-coated tungsten carbide specimens.

  8. 10 CFR 50.66 - Requirements for thermal annealing of the reactor pressure vessel.

    Science.gov (United States)

    2010-01-01

    ... Requirements for thermal annealing of the reactor pressure vessel. (a) For those light water nuclear power... life of these components. (B) The effects of localized high temperatures on degradation of the concrete... thermal annealing or to operate the nuclear power reactor following the annealing must be identified....

  9. 78 FR 31577 - Diffusion-Annealed, Nickel-Plated Flat-Rolled Steel Products From Japan

    Science.gov (United States)

    2013-05-24

    ...)] Diffusion-Annealed, Nickel-Plated Flat-Rolled Steel Products From Japan Determination On the basis of the... reason of imports from Japan of diffusion-annealed, nickel-plated flat-rolled steel products, provided... diffusion-annealed, nickel-plated flat-rolled steel products from Japan. Accordingly, effective March...

  10. Natural gas monthly, May 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-05-01

    The Natural Gas Monthly highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. The feature article this month is ``Restructuring energy industries: Lessons from natural gas.`` 6 figs., 26 tabs.

  11. Natural gas monthly, June 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-06-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. The feature article this month is the executive summary from Natural Gas 1994: Issues and Trends. 6 figs., 31 tabs.

  12. Natural gas monthly, January 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. The featured article for this month is on US coalbed methane production.

  13. Natural gas monthly, December 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    The Natural Gas Monthly highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. The article this month is entitled ``Recent Trends in Natural Gas Spot Prices.`` 6 figs., 27 tabs.

  14. Influence of annealing temperature on the electrochemical and surface properties of the 5-V spinel cathode material LiCr0.2Ni0.4Mn1.4O4 synthesized by a sol–gel technique

    DEFF Research Database (Denmark)

    Younesi, Reza; Malmgren, Sara; Edström, Kristina

    2014-01-01

    LiCr0.2Ni0.4Mn1.4O4 was synthesized by a sol–gel technique in which tartaric acid was used as oxide precursor. The synthesized powder was annealed at five different temperatures from 600 to 1,000 °C and tested as a 5-V cathode material in Li-ion batteries. The study shows that annealing at higher...... values higher than 85 % at C/2, C, and 2C rates at 25 °C after 50 cycles. Annealing at 600–800 °C resulted in formation of spinel particles smaller than 200 nm, while almost micron-sized particles were obtained at 900– 1,000 °C. Chromium deficiency was detected at the surface of the active materials...... annealed at low temperatures. The XPS results indicate presence of Cr6+ impurity when the annealing temperature was not high enough. The study revealed that increased annealing temperature is beneficial for both improved electrochemical performance of LiCr0.2Ni0.4Mn1.4O4 and for avoiding formation of Cr6...

  15. First application of quantum annealing to IMRT beamlet intensity optimization

    Science.gov (United States)

    Nazareth, Daryl P.; Spaans, Jason D.

    2015-05-01

    Optimization methods are critical to radiation therapy. A new technology, quantum annealing (QA), employs novel hardware and software techniques to address various discrete optimization problems in many fields. We report on the first application of quantum annealing to the process of beamlet intensity optimization for IMRT. We apply recently-developed hardware which natively exploits quantum mechanical effects for improved optimization. The new algorithm, called QA, is most similar to simulated annealing, but relies on natural processes to directly minimize a system’s free energy. A simple quantum system is slowly evolved into a classical system representing the objective function. If the evolution is sufficiently slow, there are probabilistic guarantees that a global minimum will be located. To apply QA to IMRT-type optimization, two prostate cases were considered. A reduced number of beamlets were employed, due to the current QA hardware limitations. The beamlet dose matrices were computed using CERR and an objective function was defined based on typical clinical constraints, including dose-volume objectives, which result in a complex non-convex search space. The objective function was discretized and the QA method was compared to two standard optimization methods, simulated annealing and Tabu search, run on a conventional computing cluster. Based on several runs, the average final objective function value achieved by the QA was 16.9 for the first patient, compared with 10.0 for Tabu and 6.7 for the simulated annealing (SA) method. For the second patient, the values were 70.7 for the QA, 120.0 for Tabu and 22.9 for the SA. The QA algorithm required 27-38% of the time required by the other two methods. In this first application of hardware-enabled QA to IMRT optimization, its performance is comparable to Tabu search, but less effective than the SA in terms of final objective function values. However, its speed was 3-4 times faster than the other two methods

  16. Radiation and annealing response of WWER 440 beltline welding seams

    Energy Technology Data Exchange (ETDEWEB)

    Viehrig, Hans-Werner, E-mail: h.w.viehrig@hzdr.de; Houska, Mario; Altstadt, Eberhard

    2015-01-15

    Highlights: • Investigation of the beltline welding seam from decommissioned reactor pressure vessels. • The Master Curve based reference temperature varies strongly through the thickness. • This variation is mainly caused by the intrinsic weld bead structure. • The Charpy-V based ductile-to-brittle temperature shift does not correspond to the prediction. • The mitigation of the irradiation induced embrittlement by annealing has been confirmed. - Abstract: The focus of this paper is on the irradiation response and the effect of thermal annealing in weld materials extracted from decommissioned WWER 440 reactor pressure vessels of the nuclear power plant Greifswald. The characterisation is based on the measurement of the hardness, the yield stress, the Master Curve reference temperature, T{sub 0}, and the Charpy-V transition temperature through the thickness of multi-layer beltline welding seams in the irradiated and the thermally annealed condition. Additionally, the weld bead structure was characterised by light microscopic studies. We observed a large variation in the through thickness T{sub 0} values in the irradiated as well as in thermally annealed condition. The T{sub 0} values measured with the T–S-oriented Charpy size SE(B) specimens cut from different thickness locations of the multilayer welding seams strongly depend on the intrinsic weld bead structure along the crack tip. The Master Curve, T{sub 0}, and Charpy-V, TT{sub 47J}, based ductile-to-brittle transition temperature progressions through the thickness of the multi-layer welding seam do not correspond to the forecast according to the Russian code. In general, the fracture toughness values at cleavage failure, K{sub Jc}, measured on SE(B) specimens from the irradiated and large-scale thermally annealed beltline welding seams follow the Master Curve description, but more than the expected number lie outside the curves for 2% and 98% fracture probability. In this case the test standard ASTM

  17. US Monthly Pilot Balloon Observations

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Monthly winds aloft summary forms summarizing Pilot Balloon observational data for the United States. Generally labeled as Form 1114, and then transitioning to Form...

  18. Monthly energy review, August 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-08-26

    This publication presents information for the month of August, 1993 on the following: Energy overview; energy consumption; petroleum; natural gas; oil and gas resource development; coal; electricity; nuclear energy; energy prices, and international energy.

  19. Monthly Energy Review, July 1992

    Energy Technology Data Exchange (ETDEWEB)

    None

    1992-07-27

    The Monthly Energy Review is prepared by the Energy Information Administration. Topics discussed include: Energy Overview, Energy Consumption, Petroleum, Natural Gas, Oil and Gas Resource Development, Coal, Electricity, Nuclear Energy, Energy Prices, International Energy. (VC)

  20. Monthly energy review, July 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    This document presents an overview of recent monthly energy statistics. Activities covered include: U.S. production, consumption, trade, stock, and prices for petroleum, coal, natural gas, electricity, and nuclear energy.

  1. Monthly energy review, August 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    This report presents an overview of recent monthly energy statistics. The statistics cover the major activities of U.S. production, consumption, trade, stocks, and prices for petroleum, coal, natural gas, electricity, and nuclear energy.

  2. Monthly energy review, August 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-08-26

    This publication presents information for the month of August, 1993 on the following: Energy overview; energy consumption; petroleum; natural gas; oil and gas resource development; coal; electricity; nuclear energy; energy prices, and international energy.

  3. Your Child's Development: 15 Months

    Science.gov (United States)

    ... Child Too Busy? Helping Your Child Adjust to Preschool School Lunches Kids and Food: 10 Tips for Parents Healthy Habits for TV, Video Games, and the Internet Your Child's Development: 15 Months KidsHealth > For Parents > Your Child's Development: ...

  4. Your Child's Development: 6 Months

    Science.gov (United States)

    ... Child Too Busy? Helping Your Child Adjust to Preschool School Lunches Kids and Food: 10 Tips for Parents Healthy Habits for TV, Video Games, and the Internet Your Child's Development: 6 Months KidsHealth > For Parents > Your Child's Development: ...

  5. Your Child's Development: 2 Months

    Science.gov (United States)

    ... Child Too Busy? Helping Your Child Adjust to Preschool School Lunches Kids and Food: 10 Tips for Parents Healthy Habits for TV, Video Games, and the Internet Your Child's Development: 2 Months KidsHealth > For Parents > Your Child's Development: ...

  6. Monthly energy review, August 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-08-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. The MER is intended for use by Members of Congress, Federal and State agencies, energy analysts, and the general public. 37 figs., 73 tabs.

  7. Natural gas monthly, July 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. 6 figs., 25 tabs.

  8. Natural gas monthly, June 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. 6 figs., 25 tabs.

  9. Natural gas monthly, August 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-08-24

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information.

  10. Natural gas monthly, June 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. 6 figs., 27 tabs.

  11. Natural gas monthly, April 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-04-26

    The National Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information.

  12. Natural gas monthly, September 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    The National Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. 6 figs., 27 tabs.

  13. Natural gas monthly, June 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-06-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. 6 figs., 24 tabs.

  14. Natural gas monthly, October 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-10-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. 6 figs., 27 tabs.

  15. Monthly energy review, April 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-04-01

    This report presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of U.S. production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy data. A brief summary of the monthly and historical comparison data is provided in Section 1 of the report. A highlight section of the report provides an assessment of summer 1997 motor gasoline price increases.

  16. Monthly energy review, April 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-04-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. The MER is intended for use by Members of Congress, Federal and State agencies, energy analysts, and the general public.

  17. Natural gas monthly, May 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time the NGM features articles designed to assist readers in using and interpreting natural gas information. 6 figs., 27 tabs.

  18. Natural gas monthly: December 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. Articles are included which are designed to assist readers in using and interpreting natural gas information.

  19. Natural gas monthly, July 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. 6 figs., 25 tabs.

  20. Natural Gas Monthly, March 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-25

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information.

  1. Natural gas monthly, July 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-07-20

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information.

  2. Natural gas monthly, November 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-11-29

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground state data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information.

  3. Natural gas monthly, October 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-10-23

    The Natural Gas Monthly highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. A glossary of the terms used in this report is provided to assist readers in understanding the data presented in this publication. 6 figs., 30 tabs.

  4. Controlling preferred orientation and electrical conductivity of zinc oxide thin films by post growth annealing treatment

    Energy Technology Data Exchange (ETDEWEB)

    Kennedy, J., E-mail: J.Kennedy@gns.cri.nz [National Isotope Centre, GNS Science, PO Box 31312, Lower Hutt 5010 (New Zealand); The MacDiarmid Institute for Advanced Materials and Nanotechnology (New Zealand); Murmu, P.P.; Leveneur, J. [National Isotope Centre, GNS Science, PO Box 31312, Lower Hutt 5010 (New Zealand); Markwitz, A. [National Isotope Centre, GNS Science, PO Box 31312, Lower Hutt 5010 (New Zealand); The MacDiarmid Institute for Advanced Materials and Nanotechnology (New Zealand); Futter, J. [National Isotope Centre, GNS Science, PO Box 31312, Lower Hutt 5010 (New Zealand)

    2016-03-30

    Graphical abstract: - Highlights: • Annealing dependent microstructural evolution and change in conductivity of ZnO films. • Preferential growth along (0 0 2) and (1 0 0) planes in air and vacuum annealed films. • Resistivity varied between 10{sup 6} and 10{sup −2} Ω cm depending on annealing conditions. • Hydrogen interstitials, and hydrogen-oxygen vacancy complexes affect the conductivity. • Narrow ZnO bandgap assigned to band tail effect related to intrinsic defects states. - Abstract: We report the microstructural evolution of the preferred orientation and electrical conductivity of zinc oxide (ZnO) thin films prepared by ion beam sputtering. Elastic recoil detection analysis results showed 0.6 at% H in as-deposited film which decreased to 0.35 at% in air annealed film due to H diffusion. XRD results showed that the preferred orientation can be tuned by selecting annealing conditions. Vacuum annealed films exhibited (1 0 0) orientation, whereas air annealed film showed (0 0 2) orientation. The annealing conditions caused a dramatic increase in the resistivity of air annealed films (∼10{sup 6} Ω cm), whereas vacuum annealed films showed lower resistivity (∼10{sup −2} Ω cm). High resistivity in air annealed film is attributed to the lack of hydrogen interstitials and hydrogen-oxygen vacancy complexes. Raman results supported the XRD results which demonstrated that annealing assisted in recovery of the crystalline disorder in as-deposited films. Air annealed film exhibited the highest optical transmission (89.7%) in the UV–vis region compared to as-deposited and vacuum annealed films (∼85%). Optical bandgap was found to vary between 3.11 eV and 3.18 eV in as-deposited and annealed films, respectively. The bandgap narrowing is associated with the intrinsic defects which introduced defect states resulting in band tail in ZnO films.

  5. Improvement on the electrical characteristics of Pd/HfO2/6H-SiC MIS capacitors using post deposition annealing and post metallization annealing

    Science.gov (United States)

    Esakky, Papanasam; Kailath, Binsu J.

    2017-08-01

    HfO2 as a gate dielectric enables high electric field operation of SiC MIS structure and as gas sensor HfO2/SiC capacitors offer higher sensitivity than SiO2/SiC capacitors. The issue of higher density of oxygen vacancies and associated higher leakage current necessitates better passivation of HfO2/SiC interface. Effect of post deposition annealing in N2O plasma and post metallization annealing in forming gas on the structural and electrical characteristics of Pd/HfO2/SiC MIS capacitors are reported in this work. N2O plasma annealing suppresses crystallization during high temperature annealing thereby improving the thermal stability and plasma annealing followed by rapid thermal annealing in N2 result in formation of Hf silicate at the HfO2/SiC interface resulting in order of magnitude lower density of interface states and gate leakage current. Post metallization annealing in forming gas for 40 min reduces interface state density by two orders while gate leakage current density is reduced by thrice. Post deposition annealing in N2O plasma and post metallization annealing in forming gas are observed to be effective passivation techniques improving the electrical characteristics of HfO2/SiC capacitors.

  6. Effect of argon-annealing and subsequent oxygen-annealing on the superconductivity and structure of Tl 2CaBa 2Cu 2O 8- x

    Science.gov (United States)

    Gopalakrishnan, I. K.; Sastry, P. V. P. S. S.; Rajagopal, H.; Sequeira, A.; Yakhmi, J. V.; Iyer, R. M.

    1989-08-01

    Annealing the single-phase Tl 2CaBa 2Cu 2O 8 superconductor ( Tc=108 K) in argon environment at 950 K for 24 h brings the Tc down to ≅80 K. Re-annealing the samples in oxygen under similar conditions restores the Tc to 105±5 K. Rietveld profile refinement of the neutron diffraction spectra of the argon-annealed samples indicates that some Tl-ions, presumably Tl 1+, move from the Tl double-layers to occupy Ca-sites. Upon subsequent annealing in oxygen, however, these Tl-ions escape from the lattice. Implications of this and other structural features are described.

  7. List-Based Simulated Annealing Algorithm for Traveling Salesman Problem.

    Science.gov (United States)

    Zhan, Shi-hua; Lin, Juan; Zhang, Ze-jun; Zhong, Yi-wen

    2016-01-01

    Simulated annealing (SA) algorithm is a popular intelligent optimization algorithm which has been successfully applied in many fields. Parameters' setting is a key factor for its performance, but it is also a tedious work. To simplify parameters setting, we present a list-based simulated annealing (LBSA) algorithm to solve traveling salesman problem (TSP). LBSA algorithm uses a novel list-based cooling schedule to control the decrease of temperature. Specifically, a list of temperatures is created first, and then the maximum temperature in list is used by Metropolis acceptance criterion to decide whether to accept a candidate solution. The temperature list is adapted iteratively according to the topology of the solution space of the problem. The effectiveness and the parameter sensitivity of the list-based cooling schedule are illustrated through benchmark TSP problems. The LBSA algorithm, whose performance is robust on a wide range of parameter values, shows competitive performance compared with some other state-of-the-art algorithms.

  8. Temperature-dependent permittivity of annealed and unannealed gold films

    CERN Document Server

    Shen, Po-Ting; Lin, Cheng-Wei; Liu, Hsiang-Lin; Chang, Chih-Wei; Chu, Shi-Wei

    2016-01-01

    Due to local field enhancement and subwavelength confinements, nano-plasmonics provide numerous novel applications. Simultaneously, as an efficient nanoscale heat generator from inherent absorption, thermo-plasmonics is emerging as an important branch. However, although significant temperature increase is involved in applications, detailed characterization of metal permittivity at different temperatures is lacking. In this work, we extract the permittivity of gold film from 300K to the annealing temperature of 570K. By comparing annealed and unannealed films, more than one-order difference in thermo-derivative of permittivity is revealed, resulting in unexpectedly large variation of plasmonic properties. Our result is valuable not only for characterizing extensively used unannealed nanoparticles, but also for designing future thermo-nano-plasmonic systems.

  9. Ranking important nodes in complex networks by simulated annealing

    Science.gov (United States)

    Sun, Yu; Yao, Pei-Yang; Wan, Lu-Jun; Shen, Jian; Zhong, Yun

    2017-02-01

    In this paper, based on simulated annealing a new method to rank important nodes in complex networks is presented. First, the concept of an importance sequence (IS) to describe the relative importance of nodes in complex networks is defined. Then, a measure used to evaluate the reasonability of an IS is designed. By comparing an IS and the measure of its reasonability to a state of complex networks and the energy of the state, respectively, the method finds the ground state of complex networks by simulated annealing. In other words, the method can construct a most reasonable IS. The results of experiments on real and artificial networks show that this ranking method not only is effective but also can be applied to different kinds of complex networks. Project supported by the National Natural Science Foundation of China (Grant No. 61573017) and the Natural Science Foundation of Shaanxi Province, China (Grant No. 2016JQ6062).

  10. Annealing free, clean graphene transfer using alternative polymer scaffolds

    Science.gov (United States)

    Wood, Joshua D.; Doidge, Gregory P.; Carrion, Enrique A.; Koepke, Justin C.; Kaitz, Joshua A.; Datye, Isha; Behnam, Ashkan; Hewaparakrama, Jayan; Aruin, Basil; Chen, Yaofeng; Dong, Hefei; Haasch, Richard T.; Lyding, Joseph W.; Pop, Eric

    2015-02-01

    We examine the transfer of graphene grown by chemical vapor deposition (CVD) with polymer scaffolds of poly(methyl methacrylate) (PMMA), poly(lactic acid) (PLA), poly(phthalaldehyde) (PPA), and poly(bisphenol A carbonate) (PC). We find that optimally reactive PC scaffolds provide the cleanest graphene transfers without any annealing, after extensive comparison with optical microscopy, x-ray photoelectron spectroscopy, atomic force microscopy, and scanning tunneling microscopy. Comparatively, films transferred with PLA, PPA, PMMA/PC, and PMMA have a two-fold higher roughness and a five-fold higher chemical doping. Using PC scaffolds, we demonstrate the clean transfer of CVD multilayer graphene, fluorinated graphene, and hexagonal boron nitride. Our annealing free, PC transfers enable the use of atomically-clean nanomaterials in biomolecule encapsulation and flexible electronic applications.

  11. A cooperative fast annealing coevolutionary algorithm for protein motif extraction

    Institute of Scientific and Technical Information of China (English)

    CHEN Chao; TIAN YuanXin; ZOU XiaoYong; CAI PeiXiang; MO JinYuan

    2007-01-01

    By integrating the cooperative approach with the fast annealing coevolutionary algorithm (FAEA), a so-called cooperative fast annealing coevolutionary algorithm (CFACA) is presented in this paper for the purpose of solving high-dimensional problems. After the partition of the search space in CFACA, each smaller one is then searched by a separate FAEA. The fitness function is evaluated by combining sub-solutions found by each of the FAEAs. It demonstrates that the CFACA outperforms the FAEA in the domain of function optimization, especially in terms of convergence rate. The current algorithm is also applied to a real optimization problem of protein motif extraction. And a satisfactory result has been obtained with the accuracy of prediction achieving 67.0%, which is in agreement with the result in the PROSITE database.

  12. Variable neighbourhood simulated annealing algorithm for capacitated vehicle routing problems

    Science.gov (United States)

    Xiao, Yiyong; Zhao, Qiuhong; Kaku, Ikou; Mladenovic, Nenad

    2014-04-01

    This article presents the variable neighbourhood simulated annealing (VNSA) algorithm, a variant of the variable neighbourhood search (VNS) combined with simulated annealing (SA), for efficiently solving capacitated vehicle routing problems (CVRPs). In the new algorithm, the deterministic 'Move or not' criterion of the original VNS algorithm regarding the incumbent replacement is replaced by an SA probability, and the neighbourhood shifting of the original VNS (from near to far by k← k+1) is replaced by a neighbourhood shaking procedure following a specified rule. The geographical neighbourhood structure is introduced in constructing the neighbourhood structures for the CVRP of the string model. The proposed algorithm is tested against 39 well-known benchmark CVRP instances of different scales (small/middle, large, very large). The results show that the VNSA algorithm outperforms most existing algorithms in terms of computational effectiveness and efficiency, showing good performance in solving large and very large CVRPs.

  13. Effect of hydrogen annealing on characteristics of polycrystalline silicon

    Institute of Scientific and Technical Information of China (English)

    GOU Xianfang; XU Ying; LI Xudong; HENG Yang; MA Lifen; REN Bingyan

    2006-01-01

    The characteristics of mc-Si used for solar cells during H2 ambient annealing at 800-1200 ℃ were investigated by means of FTIR and QSSPCD. The results reveal that grain boundaries or defects in mc-Si may facilitate the formation of oxygen precipitates, and the formation of oxygen precipitates has deleterious effect on the lifetime of mc-Si. Decreasing lifetime could result from the formation of new recombination during annealing. Additionally, It is found that hydrogen may facilitate the formation of oxygen precipitates in mc-Si. On the other hand, the diffusion of hydrogen may passivate the defects/boundaries and it is beneficial to the lifetime of mc-Si.

  14. Multi-Objective Simulating Annealing for Permutation Flow Shop Problems

    Science.gov (United States)

    Mokotoff, E.; Pérez, J.

    2007-09-01

    Real life scheduling problems require more than one criterion. Nevertheless, the complex nature of the Permutation Flow Shop problem has prevented the development of models with multiple criteria. Considering only one regular criterion, this scheduling problem was shown to be NP-complete. The Multi-Objective Simulated Annealing (MOSA) methods are metaheuristics based on Simulated Annealing to solve Multi-Objective Combinatorial Optimization (MOCO) problems, like the problem at hand. Starting from the general MOSA method introduced by Loukil et al. [1], we developed MOSA models to provide the decision maker with efficient solutions for the Permutation Flow Shop problem (common in the production of ceramic tiles). In this paper we present three models: two bicriteria models and one based on satisfaction levels for the main criterion.

  15. Hardening by annealing and softening by deformation in nanostructured metals

    DEFF Research Database (Denmark)

    Huang, X.; Hansen, N.; Tsuji, N.

    2006-01-01

    -dislocation and dislocation-interface reactions, such that heat treatment reduces the generation and interaction of dislocations, leading to an increase in strength and a reduction in ductility. A subsequent deformation step may restore the dislocation structure and facilitate the yielding process when the metal is stressed......We observe that a nanostructured metal can be hardened by annealing and softened when subsequently deformed, which is in contrast to the typical behavior of a metal. Microstructural investigation points to an effect of the structural scale on fundamental mechanisms of dislocation....... As a consequence, the strength decreases and the ductility increases. These observations suggest that for materials such as the nanostructured aluminum studied here, deformation should be used as an optimizing procedure instead of annealing....

  16. Post annealing investigations of thin praseodymia films on Si(111)

    Energy Technology Data Exchange (ETDEWEB)

    Gevers, Sebastian; Bruns, Daniel; Weisemoeller, Thomas; Deiter, Carsten; Wollschlaeger, Joachim [Fachbereich Physik, Universitaet Osnabrueck (Germany)

    2008-07-01

    Due to its large oxygen capacity and oxygen mobility praseodymia is interesting for applications in modern heterogenous catalysis. For instance the selectivity of praseodymia for carbon compounds is advantageous in olefiant gas synthesis. The investigation of annealing processes leads to a better understanding of the oxygen transport in the praseodymia films. In this context thin PrO{sub 2} films were annealed at temperatures from 300 C up to 600 C under UHV conditions before they were analysed with spot analysis profile low electron energy diffraction (SPALEED). The diffraction pattern indicates a phase transition to Pr{sub 2}O{sub 3} at the surface. Furthermore X-ray diffraction experiments (XRD) show a partial subsurface phase transition from PrO{sub 2} into various oxidation states including Pr{sub 2}O{sub 3}.

  17. Radiation annealing of gallium arsenide implanted with sulphur

    CERN Document Server

    Ardyshev, V M

    2002-01-01

    Sulfur ions were implanted in a semi-insulating GaAs. Photon annealing (805 deg C/(10-12) s) and the thermal one (800 deg C/30 min) were conducted under SiO sub 2 -films coating obtained by different ways. Contents of GaAs components in films were determined from Rutherford backscattering spectra; concentration profiles of electrons were measured by the voltage-capacitance method. Diffusion of sulfur was shown to go in two directions - to the surface and into bulk of GaAs. The first process was induced by vacancies that had been formed near the surface of semiconductors during the dielectric coating. The coefficient of the bulk-diffusion and diffusion-to-surface of sulfur ions under photon annealing was twice as much as that under thermal one. The doping efficiency was also larger

  18. Tunable cobalt nanoparticle synthesis by intense pulse flash annealing

    Directory of Open Access Journals (Sweden)

    Aaron Mosey

    2017-05-01

    Full Text Available Magnetically susceptible materials can serve as a basis for the directed assembly of nanoscale network devices which can be used to extract energy from phase change materials. So far, matrix production cost has been a prohibitive factor in the realization of real world applications. Here we report a cost-effective method to synthesize magnetic nanoparticles. Samples were fabricated by sputtering magnetic thin films on carbon nanotube substrates followed by xenon intense pulsed light flash annealing. The results indicate that spatially ordered magnetic spheres can be tuned by various parameters such as initial thin film thickness, xenon lamp exposure excitation energy, local surface geometries, and the presence of an external magnetic field during annealing.

  19. Tunable cobalt nanoparticle synthesis by intense pulse flash annealing

    Science.gov (United States)

    Mosey, Aaron; Gaire, Babu; Kim, Jeongwhan; Ryu, Jong Eun; Cheng, Ruihua

    2017-05-01

    Magnetically susceptible materials can serve as a basis for the directed assembly of nanoscale network devices which can be used to extract energy from phase change materials. So far, matrix production cost has been a prohibitive factor in the realization of real world applications. Here we report a cost-effective method to synthesize magnetic nanoparticles. Samples were fabricated by sputtering magnetic thin films on carbon nanotube substrates followed by xenon intense pulsed light flash annealing. The results indicate that spatially ordered magnetic spheres can be tuned by various parameters such as initial thin film thickness, xenon lamp exposure excitation energy, local surface geometries, and the presence of an external magnetic field during annealing.

  20. Thermal Performance of an Annealed Pyrolytic Graphite Solar Collector

    Science.gov (United States)

    Jaworske, Donald A.; Hornacek, Jennifer

    2002-01-01

    A solar collector having the combined properties of high solar absorptance, low infrared emittance, and high thermal conductivity is needed for applications where solar energy is to be absorbed and transported for use in minisatellites. Such a solar collector may be used with a low temperature differential heat engine to provide power or with a thermal bus for thermal switching applications. One concept being considered for the solar collector is an Al2O3 cermet coating applied to a thermal conductivity enhanced polished aluminum substrate. The cermet coating provides high solar absorptance and the polished aluminum provides low infrared emittance. Annealed pyrolytic graphite embedded in the aluminum substrate provides enhanced thermal conductivity. The as-measured thermal performance of an annealed pyrolytic graphite thermal conductivity enhanced polished aluminum solar collector, coated with a cermet coating, will be presented.

  1. Stochastic seismic inversion using greedy annealed importance sampling

    Science.gov (United States)

    Xue, Yang; Sen, Mrinal K.

    2016-10-01

    A global optimization method called very fast simulated annealing (VFSA) inversion has been applied to seismic inversion. Here we address some of the limitations of VFSA by developing a new stochastic inference method, named greedy annealed importance sampling (GAIS). GAIS combines VFSA and greedy importance sampling (GIS), which uses a greedy search in the important regions located by VFSA, in order to attain fast convergence and provide unbiased estimation. We demonstrate the performance of GAIS with application to seismic inversion of field post- and pre-stack datasets. The results indicate that GAIS can improve lateral continuity of the inverted impedance profiles and provide better estimation of uncertainties than using VFSA alone. Thus this new hybrid method combining global and local optimization methods can be applied in seismic reservoir characterization and reservoir monitoring for accurate estimation of reservoir models and their uncertainties.

  2. Effects of Primary Annealing Condition on Recrystallization Texture in a Grain Oriented Silicon Steel

    Institute of Scientific and Technical Information of China (English)

    Yuhui SHA; Fang ZHANG; Song LI; Xiaoyu GAO; Jiazhen XU; Liang ZUO

    2004-01-01

    The recrystallization texture in grain oriented silicon steel sheets, which were annealed at different primary annealing temperatures with and without an electric field, was investigated. An automated electron backscattered diffraction (EBSD) technique was used to analyze the recrystallization texture. It was found that recovery and application of electric field in primary annealing lead to an increase of {001} component and a decrease of {111} component after annealing at 900℃. The development of recrystallization texture can be explained in terms of the effects of electric field and primary annealing temperature on recovery.

  3. Influences of Annealing on Residual Stress and Structure of HfO2 Films

    Institute of Scientific and Technical Information of China (English)

    SHEN Yan-Ming; SHAO Shu-Ying; DENG Zhen-Xia; HE Hong-Bo; SHAO Jian-Da; FAN Zheng-Xiu

    2007-01-01

    HfO2 films are deposited on BK7 glass substrates by electron beam evaporation. The influences of annealing between 100℃ and 400℃ on residual stresses and structures of HfO2 films are studied. It is found that little differences of spectra, residual stresses and structures are obtained after annealing at lower temperatures. After annealing at higher temperatures, the spectra shift to short wavelength, the residual stress increases with the increasing annealing temperature. At the same time, the crystallite size increases and interplanar distance decreases. The variations of optical spectra and residual stress correspond to the evolutions of structures induced by annealing.

  4. Annealing-induced evolution of transformation characteristics in TiNi shape memory alloys

    Science.gov (United States)

    Wang, Z. G.; Zu, X. T.; Feng, X. D.; Zhu, S.; Zhou, J. M.; Wang, L. M.

    2004-11-01

    The effect of annealing on transformation characteristics of TiNi shape memory alloys (SMAs) was investigated by differential scanning calorimetry (DSC) and the evolution of the microstructure was studied using positron annihilation technology (PAT) and transmission electron microscopy (TEM). The results showed that transformation characteristics depend on the annealing temperature. The R-phase transformation appeared at low annealing temperature. The R-phase disappeared and austensite transformed into martensite directly as the annealing temperature exceeded 550 °C. With increasing annealing temperature, the vacancy cluster and dislocation related positron lifetime decreased. Changes in transformation characteristics can be attributed to the evolution of the microstructrue of the TiNi specimen.

  5. Effect of thermal-annealing on the magnetoresistance of manganite-based junctions

    Institute of Scientific and Technical Information of China (English)

    Xie Yan-Wu; Shen Bao-Gen; Sun Ji-Rong

    2008-01-01

    Thermal-annealing has been widely used in modulating the oxygen content of manganites. In this work, we have studied the effect of annealing on the transport properties and magnetoresistance of junctions composed of a La0.9Ca0.1MnO3+δ film and a Nb-doped SrTiO3 substrate. We have demonstrated that the magnetoresistance of junctions is strongly dependent on the annealing conditions: From the junction annealed-in-air to the junction annealed-in-vacuum, the magnetoresistance near 0-V bias can vary from ~-60% to~0. A possible mechanism accounting for this phenomenon is discussed.

  6. Influence of deposition parameters and annealing on Cu{sub 2}ZnSnS{sub 4} thin films grown by SILAR

    Energy Technology Data Exchange (ETDEWEB)

    Patel, Kinjal; Shah, Dimple V. [Department of Applied Physics, S.V. National Institute of Technology, Surat 395007 (India); Kheraj, Vipul, E-mail: vipulkheraj@gmail.com [Department of Applied Physics, S.V. National Institute of Technology, Surat 395007 (India); Department of Electrical and Computer Engineering, University of Utah, Salt Lake City, UT 84112 (United States)

    2015-02-15

    Highlights: • Optimisation of Cu{sub 2}ZnSnS{sub 4} (CZTS) thin film deposition using SILAR method. • Study on effects of annealing at different temperature under two different ambients, viz. sulphur and tin sulphide. • Formation of CZTS thin films with good crystalline quality confirmed by XRD and Raman spectra. - Abstract: Cu{sub 2}ZnSnS{sub 4} (CZTS) thin films were deposited on glass substrates using Successive Ionic Layer Adsorption and Reaction (SILAR) technique at the room-temperature. The deposition parameters such as concentration of precursors and number of cycles were optimised for the deposition of uniform CZTS thin films. Effects of annealing at different temperature under two different ambient, viz. sulphur and tin sulphide have also been investigated. The structural and optical properties of the films were studied using X-ray diffraction, scanning electron microscopy, Raman spectroscopy and UV-visible spectra in light with the deposition parameters and annealing conditions. It is observed that a good quality CZTS film can be obtained by SILAR at room temperature followed by annealing at 500 °C in presence of sulphur.

  7. Estimation of the parameters of ETAS models by Simulated Annealing

    OpenAIRE

    Lombardi, Anna Maria

    2015-01-01

    This paper proposes a new algorithm to estimate the maximum likelihood parameters of an Epidemic Type Aftershock Sequences (ETAS) model. It is based on Simulated Annealing, a versatile method that solves problems of global optimization and ensures convergence to a global optimum. The procedure is tested on both simulated and real catalogs. The main conclusion is that the method performs poorly as the size of the catalog decreases because the effect of the correlation of the ETAS parameters is...

  8. Reverse degradation of nickel graphene junction by hydrogen annealing

    CERN Document Server

    Zhang, Zhenjun; Agnihotri, Pratik; Lee, Ji Ung; Lloyd, Jim R

    2016-01-01

    Metal contacts are fundamental building components for graphene based electronic devices and their properties are greatly influenced by interface quality during device fabrication, leading to resistance variation. Here we show that nickel graphene junction degrades after air exposure, due to interfacial oxidation, thus creating a tunneling barrier. Most importantly, we demonstrate that hydrogen annealing at moderate temperature (300 0C) is an effective technique to reverse the degradation.

  9. Adaptive Simulated Annealing Based Protein Loop Modeling of Neurotoxins

    Institute of Scientific and Technical Information of China (English)

    陈杰; 黄丽娜; 彭志红

    2003-01-01

    A loop modeling method, adaptive simulated annealing, for ab initio prediction of protein loop structures, as an optimization problem of searching the global minimum of a given energy function, is proposed. An interface-friendly toolbox-LoopModeller in Windows and Linux systems, VC++ and OpenGL environments is developed for analysis and visualization. Simulation results of three short-chain neurotoxins modeled by LoopModeller show that the method proposed is fast and efficient.

  10. Reverse degradation of nickel graphene junction by hydrogen annealing

    Directory of Open Access Journals (Sweden)

    Zhenjun Zhang

    2016-02-01

    Full Text Available Metal contacts are fundamental building components for graphene based electronic devices and their properties are greatly influenced by interface quality during device fabrication, leading to resistance variation. Here we show that nickel graphene junction degrades after air exposure, due to interfacial oxidation, thus creating a tunneling barrier. Most importantly, we demonstrate that hydrogen annealing at moderate temperature (300 0C is an effective technique to reverse the degradation.

  11. Reverse degradation of nickel graphene junction by hydrogen annealing

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Zhenjun; Yang, Fan; Agnihotri, Pratik; Lee, Ji Ung; Lloyd, J. R., E-mail: jlloyd@sunypoly.edu [College of Nanoscience and Engineering, SUNY Polytechnic Institute, Albany, NY USA 12203 (United States)

    2016-02-15

    Metal contacts are fundamental building components for graphene based electronic devices and their properties are greatly influenced by interface quality during device fabrication, leading to resistance variation. Here we show that nickel graphene junction degrades after air exposure, due to interfacial oxidation, thus creating a tunneling barrier. Most importantly, we demonstrate that hydrogen annealing at moderate temperature (300 {sup 0}C) is an effective technique to reverse the degradation.

  12. Dating thermal events at Cerro Prieto using fission track annealing

    Energy Technology Data Exchange (ETDEWEB)

    Sanford, S.J.; Elders, W..

    1981-01-01

    Data from laboratory experiments and geologic fading studies were compiled from published sources to produce lines of iso-annealing for apatite in time-temperature space. Fission track ages were calculated for samples from two wells at Cerro Prieto, one with an apparently simple and one with an apparently complex thermal history. Temperatures were estimated by empirical vitrinite reflectance geothermometry, fluid inclusion homogenization and oxygen isotope equilibrium. These estimates were compared with logs of measured borehole temperatures.

  13. Simulated Annealing for the 0/1 Multidimensional Knapsack Problem

    Institute of Scientific and Technical Information of China (English)

    Fubin Qian; Rui Ding

    2007-01-01

    In this paper a simulated annealing (SA) algorithm is presented for the 0/1 multidimensional knapsack problem. Problem-specific knowledge is incorporated in the algorithm description and evaluation of parameters in order to look into the performance of finite-time implementations of SA. Computational results show that SA performs much better than a genetic algorithm in terms of solution time, whilst having a modest loss of solution quality.

  14. Solving geometric constraints with genetic simulated annealing algorithm

    Institute of Scientific and Technical Information of China (English)

    刘生礼; 唐敏; 董金祥

    2003-01-01

    This paper applies genetic simulated annealing algorithm (SAGA) to solving geometric constraint problems. This method makes full use of the advantages of SAGA and can handle under-/over- constraint problems naturally. It has advantages (due to its not being sensitive to the initial values) over the Newton-Raphson method, and its yielding of multiple solutions, is an advantage over other optimal methods for multi-solution constraint system. Our experiments have proved the robustness and efficiency of this method.

  15. Thermal annealing of laser damage precursors on fused silica surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Shen, N; Miller, P E; Bude, J D; Laurence, T A; Suratwala, T I; Steele, W A; Feit, M D; Wang, L L

    2012-03-19

    Previous studies have identified two significant precursors of laser damage on fused silica surfaces at fluenes below {approx} 35 J/cm{sup 2}, photoactive impurities in the polishing layer and surface fractures. In the present work, isothermal heating is studied as a means of remediating the highly absorptive, defect structure associated with surface fractures. A series of Vickers indentations were applied to silica surfaces at loads between 0.5N and 10N creating fracture networks between {approx} 10{micro}m and {approx} 50{micro}m in diameter. The indentations were characterized prior to and following thermal annealing under various times and temperature conditions using confocal time-resolved photo-luminescence (CTP) imaging, and R/1 optical damage testing with 3ns, 355nm laser pulses. Significant improvements in the damage thresholds, together with corresponding reductions in CTP intensity, were observed at temperatures well below the glass transition temperature (T{sub g}). For example, the damage threshold on 05.N indentations which typically initiates at fluences <8 J/cm{sup 2} could be improved >35 J/cm{sup 2} through the use of a {approx} 750 C thermal treatment. Larger fracture networks required longer or higher temperature treatment to achieve similar results. At an annealing temperature > 1100 C, optical microscopy indicates morphological changes in some of the fracture structure of indentations, although remnants of the original fracture and significant deformation was still observed after thermal annealing. This study demonstrates the potential of using isothermal annealing as a means of improving the laser damage resistance of fused silica optical components. Similarly, it provides a means of further understanding the physics associated with optical damage and related mitigation processes.

  16. Transient Crystallization of an Aromatic Polyetherimide: Effect of Annealing

    Science.gov (United States)

    1991-01-01

    on the annealing behavior of an aromatic polyetherimide ( Ultem 5001). Although crystallization from the melt did not occur, crystallinity was easily...in LARC-TPI. 10-’ 3 Ultem aromatic polyetherimide, first reported by Serfaty, 15 is an amorphous thermoplastic with the following structure for a...commercially available Ultem 1000. 0 0 0n Our studies have been carried out on Ultem 5001-based materials which is a new aro- matic polyetherimide with

  17. Dating thermal events at Cerro Prieto using fission track annealing

    Energy Technology Data Exchange (ETDEWEB)

    Sanford, S.J.; Elders, W..

    1981-01-01

    Data from laboratory experiments and geologic fading studies were compiled from published sources to produce lines of iso-annealing for apatite in time-temperature space. Fission track ages were calculated for samples from two wells at Cerro Prieto, one with an apparently simple and one with an apparently complex thermal history. Temperatures were estimated by empirical vitrinite reflectance geothermometry, fluid inclusion homogenization and oxygen isotope equilibrium. These estimates were compared with logs of measured borehole temperatures.

  18. Prime factorization using quantum annealing and computational algebraic geometry

    Science.gov (United States)

    Dridi, Raouf; Alghassi, Hedayat

    2017-02-01

    We investigate prime factorization from two perspectives: quantum annealing and computational algebraic geometry, specifically Gröbner bases. We present a novel autonomous algorithm which combines the two approaches and leads to the factorization of all bi-primes up to just over 200000, the largest number factored to date using a quantum processor. We also explain how Gröbner bases can be used to reduce the degree of Hamiltonians.

  19. Prime factorization using quantum annealing and computational algebraic geometry

    Science.gov (United States)

    Dridi, Raouf; Alghassi, Hedayat

    2017-01-01

    We investigate prime factorization from two perspectives: quantum annealing and computational algebraic geometry, specifically Gröbner bases. We present a novel autonomous algorithm which combines the two approaches and leads to the factorization of all bi-primes up to just over 200000, the largest number factored to date using a quantum processor. We also explain how Gröbner bases can be used to reduce the degree of Hamiltonians. PMID:28220854

  20. Thin tungsten telluride layer preparation by thermal annealing

    Science.gov (United States)

    Lu, Wei; Zhang, Yudao; Zhu, Zusong; Lai, Jiawei; Zhao, Chuan; Liu, Xuefeng; Liu, Jing; Sun, Dong

    2016-10-01

    We report a simple method to prepare a thin Tungsten Telluride (WTe2) flake with accurate thickness control, which allows preparing and studying this two dimensional material conveniently. First, the WTe2 flake, which is relatively thick due to its strong interlayer van der Waals forces, is obtained by a conventional mechanical exfoliation method. Then, the exfoliated flake is annealed at 600 °C under a constant Ar protecting flow. Raman and atomic force spectroscopy characterizations demonstrate that thermal annealing can effectively thin down the WTe2 flake and retain its original lattice structure, though its surface smoothness is slightly deteriorated. Additionally, systematical study indicates that the thinning process strongly depends on the initial thickness of the WTe2 flake before annealing: the thinning rate increases from 0.12 nm min-1 to 0.36 nm min-1 as the initial thickness increases from 10 nm to 45 nm, while the roughness of the final product also increases with the increase of its initial thickness. However, the method fails when it is applied to WTe2 flakes thicker than 100 nm, resulting in uneven or burnt surface, which is possibly caused by big cavities formed by a large amount of defects gathered at the top surface.

  1. Rayleigh wave inversion using heat-bath simulated annealing algorithm

    Science.gov (United States)

    Lu, Yongxu; Peng, Suping; Du, Wenfeng; Zhang, Xiaoyang; Ma, Zhenyuan; Lin, Peng

    2016-11-01

    The dispersion of Rayleigh waves can be used to obtain near-surface shear (S)-wave velocity profiles. This is performed mainly by inversion of the phase velocity dispersion curves, which has been proven to be a highly nonlinear and multimodal problem, and it is unsuitable to use local search methods (LSMs) as the inversion algorithm. In this study, a new strategy is proposed based on a variant of simulated annealing (SA) algorithm. SA, which simulates the annealing procedure of crystalline solids in nature, is one of the global search methods (GSMs). There are many variants of SA, most of which contain two steps: the perturbation of model and the Metropolis-criterion-based acceptance of the new model. In this paper we propose a one-step SA variant known as heat-bath SA. To test the performance of the heat-bath SA, two models are created. Both noise-free and noisy synthetic data are generated. Levenberg-Marquardt (LM) algorithm and a variant of SA, known as the fast simulated annealing (FSA) algorithm, are also adopted for comparison. The inverted results of the synthetic data show that the heat-bath SA algorithm is a reasonable choice for Rayleigh wave dispersion curve inversion. Finally, a real-world inversion example from a coal mine in northwestern China is shown, which proves that the scheme we propose is applicable.

  2. Maximum-Entropy Inference with a Programmable Annealer.

    Science.gov (United States)

    Chancellor, Nicholas; Szoke, Szilard; Vinci, Walter; Aeppli, Gabriel; Warburton, Paul A

    2016-03-03

    Optimisation problems typically involve finding the ground state (i.e. the minimum energy configuration) of a cost function with respect to many variables. If the variables are corrupted by noise then this maximises the likelihood that the solution is correct. The maximum entropy solution on the other hand takes the form of a Boltzmann distribution over the ground and excited states of the cost function to correct for noise. Here we use a programmable annealer for the information decoding problem which we simulate as a random Ising model in a field. We show experimentally that finite temperature maximum entropy decoding can give slightly better bit-error-rates than the maximum likelihood approach, confirming that useful information can be extracted from the excited states of the annealer. Furthermore we introduce a bit-by-bit analytical method which is agnostic to the specific application and use it to show that the annealer samples from a highly Boltzmann-like distribution. Machines of this kind are therefore candidates for use in a variety of machine learning applications which exploit maximum entropy inference, including language processing and image recognition.

  3. Vacuum annealing temperature on spray In2S3 layers

    Science.gov (United States)

    Bouguila, Nourredine; Timoumi, Abdelmajid; Bouzouita, Hassen

    2014-02-01

    Indium sulfide In2S3 thick films are deposited on glass substrates using spray technique over the optimum conditions experiments (Ts = 340 °C, S/In = 2). The films are polycrystalline and have thickness of about 1.8 μm. These films are annealed in a vacuum sealed pyrex tubes (10-5 torr). Physico-chemical characterizations by SEM observation, X-ray diffraction and EDX analysis are undertaked on these films. This treatment has improved crystallinity of samples. It has allowed thus to stabilize β and γ varieties of In2S3 material. In2O3 and In6S7 phases have appeared with very weak intensities at high temperatures. The best structure quality are obtained at 300 °C for the optimum annealed temperature (Ts = 340 °C, S/In = 2), for which samples are constituted in dominance by γ phase oriented preferentially towards (1 0 2). The grain size is 42 nm of this phase. Chemical composition of such films has changed relatively to non-treated film but it seems not be affected by treatment temperature. Atomic molar ratio S/In is obtained for 0.9. Optical study shows that these layers are transparent in the visible and optical direct band gap increases as function of annealed temperature.

  4. Microstructure Evolution and Grain Growth Kinetics in Annealed Nanocrystalline Chromium

    Energy Technology Data Exchange (ETDEWEB)

    Chojnowski, Grzegorz [Warsaw University; Przenioslo, Radoslaw [Warsaw University; Sosnowska, Izabela [Warsaw University; Bukowski, Mirko [University of Saarbrucken, Saarbrucken, Germany; Natter, Harald [University of Saarbrucken, Saarbrucken, Germany; Hempelmann, Rolf [University of Saarbrucken, Saarbrucken, Germany; Fitch, Andrew [European Synchrotron Radiation Facility (ESRF); Urban, Volker S [ORNL

    2007-01-01

    The kinetics of thermal evolution of the microstructure of nanocrystalline chromium (nano-Cr) has been studied by time-resolved synchrotron radiation techniques: high-resolution powder diffraction and small-angle X-ray scattering (SAXS). The as-prepared electrodeposited nano-Cr with average grain size of 27 nm shows the same bcc structure as {alpha}-Cr. The nano-Cr cubic lattice parameter thermal expansion is the same as that of reference polycrystalline {alpha}-Cr. Annealing of nano-Cr at temperatures above 400 C leads to a grain growth process with the final grain size not exceeding 125 nm even at a temperature of 700 C. The single power-law behavior is observed by SAXS in as-prepared nano-Cr changes during annealing above 400 C. In nano-Cr samples annealed at temperatures between 400 and 700 C, the low-q part of the SAXS signal shows a Porod-type behavior while the high-q part shows a power-law Q-{alpha} with the exponent {alpha} < 4. This effect is probably due to changes of the grain surface roughness during grain growth.

  5. CDF Run II Silicon Vertex Detector Annealing Study

    CERN Document Server

    Stancari, M; Behari, S; Christian, D; Di Ruzza, B; Jindariani, S; Junk, T R; Mattson, M; Mitra, A; Mondragon, M N; Sukhanov, A

    2013-01-01

    Between Run II commissioning in early 2001 and the end of operations in September 2011, the Tevatron collider delivered 12~fb$^{-1}$ of $p\\bar{p}$ collisions at $\\sqrt{s}=1.96$ TeV to the Collider Detector at Fermilab (CDF). During that time, the CDF silicon vertex detector was subject to radiation doses of up to 12 Mrad. After the end of operations, the silicon detector was annealed for 24 days at $18^{\\circ}$C. In this paper, we present a measurement of the change in the bias currents for a subset of sensors during the annealing period. We also introduce a novel method for monitoring the depletion voltage throughout the annealing period. The observed bias current evolution can be characterized by a falling exponential term with time constant $\\tau_I=17.88\\pm0.36$(stat.)$\\pm0.25$(syst.) days. We observe an average decrease of $(27\\pm3)\\%$ in the depletion voltage, whose evolution can similarly be described by an exponential time constant of $\\tau_V=6.21\\pm0.21$ days. These results are consistent with the Ham...

  6. Excimer laser annealing to fabricate low cost solar cells

    Science.gov (United States)

    1984-01-01

    The objective is to show whether or not pulsed excimer laser annealing (PELA) of ion-implanted junctions is a cost effective replacement for diffused junctions in fabricating crystalline silicon solar cells. The preliminary economic analysis completed shows that the use of PELA to fabricate both the front junction and back surface field (BSF) would cost approximately 35 cents per peak watt (Wp), compared to a cost of 15 cents/Wp for diffusion, aluminum BSF and an extra cleaning step in the baseline process. The cost advantage of the PELA process depends on improving the average cell efficiency from 14% to 16%, which would lower the overall cost of the module by about 15 cents/Wp. An optimized PELA process compatible with commercial production is to be developed, and increased cell efficiency with sufficient product for adequate statistical analysis demonstrated. An excimer laser annealing station was set-up and made operational. The first experiment used 248 nm radiation to anneal phosphorus implants in polished and texture-etched silicon.

  7. Simulated annealing spectral clustering algorithm for image segmentation

    Institute of Scientific and Technical Information of China (English)

    Yifang Yang; and Yuping Wang

    2014-01-01

    The similarity measure is crucial to the performance of spectral clustering. The Gaussian kernel function based on the Euclidean distance is usual y adopted as the similarity mea-sure. However, the Euclidean distance measure cannot ful y reveal the complex distribution data, and the result of spectral clustering is very sensitive to the scaling parameter. To solve these problems, a new manifold distance measure and a novel simulated anneal-ing spectral clustering (SASC) algorithm based on the manifold distance measure are proposed. The simulated annealing based on genetic algorithm (SAGA), characterized by its rapid conver-gence to the global optimum, is used to cluster the sample points in the spectral mapping space. The proposed algorithm can not only reflect local and global consistency better, but also reduce the sensitivity of spectral clustering to the kernel parameter, which improves the algorithm’s clustering performance. To efficiently ap-ply the algorithm to image segmentation, the Nystr¨om method is used to reduce the computation complexity. Experimental re-sults show that compared with traditional clustering algorithms and those popular spectral clustering algorithms, the proposed algorithm can achieve better clustering performances on several synthetic datasets, texture images and real images.

  8. Nuclear techniques of analysis in diamond synthesis and annealing

    Energy Technology Data Exchange (ETDEWEB)

    Jamieson, D. N.; Prawer, S.; Gonon, P.; Walker, R.; Dooley, S.; Bettiol, A.; Pearce, J. [Melbourne Univ., Parkville, VIC (Australia). School of Physics

    1996-12-31

    Nuclear techniques of analysis have played an important role in the study of synthetic and laser annealed diamond. These measurements have mainly used ion beam analysis with a focused MeV ion beam in a nuclear microprobe system. A variety of techniques have been employed. One of the most important is nuclear elastic scattering, sometimes called non-Rutherford scattering, which has been used to accurately characterise diamond films for thickness and composition. This is possible by the use of a database of measured scattering cross sections. Recently, this work has been extended and nuclear elastic scattering cross sections for both natural boron isotopes have been measured. For radiation damaged diamond, a focused laser annealing scheme has been developed which produces near complete regrowth of MeV phosphorus implanted diamonds. In the laser annealed regions, proton induced x-ray emission has been used to show that 50 % of the P atoms occupy lattice sites. This opens the way to produce n-type diamond for microelectronic device applications. All these analytical applications utilize a focused MeV microbeam which is ideally suited for diamond analysis. This presentation reviews these applications, as well as the technology of nuclear techniques of analysis for diamond with a focused beam. 9 refs., 6 figs.

  9. Effect of Annealing Atmosphere on the Mechanical Property of Free-cutting Phosphor Bronze Alloy

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The present work is focused on the influence of annealing atmosphere on the microstructure and mechanical property of free-cutting phosphor bronze alloy. The annealing of the alloy was conducted in the three kinds of annealing atmosphere such as air, vacuum and nitrogen. After annealing, a discernable difference in recystallized grain size and lead particle size was not appeared with different annealing atmosphere. The tensile strength of the alloy annealed in air or nitrogen atmosphere was higher than that of those annealed in vacuum atmosphere. In thecase of the alloy annealed in vacuum atmosphere, the mechanical strength was reduced by vaporization of zinc. In the case of annealing in nitrogen and in air atmosphere, the sweating of lead was occurred. However, the inverse segregation of lead was suppressed by copper oxide layer on the surface annealed in air. This copper oxide layer leads to a decrease of the yield during fabrication process. Therefore, annealing of the alloy in nitrogen atmosphere is favorable in terms of the mechanical strength and yield.

  10. The NEWS Water Cycle Climatology

    Science.gov (United States)

    Rodell, Matthew; Beaudoing, Hiroko Kato; L'Ecuyer, Tristan; William, Olson

    2012-01-01

    NASA's Energy and Water Cycle Study (NEWS) program fosters collaborative research towards improved quantification and prediction of water and energy cycle consequences of climate change. In order to measure change, it is first necessary to describe current conditions. The goal of the first phase of the NEWS Water and Energy Cycle Climatology project was to develop "state of the global water cycle" and "state of the global energy cycle" assessments based on data from modern ground and space based observing systems and data integrating models. The project was a multi-institutional collaboration with more than 20 active contributors. This presentation will describe the results of the water cycle component of the first phase of the project, which include seasonal (monthly) climatologies of water fluxes over land, ocean, and atmosphere at continental and ocean basin scales. The requirement of closure of the water budget (i.e., mass conservation) at various scales was exploited to constrain the flux estimates via an optimization approach that will also be described. Further, error assessments were included with the input datasets, and we examine these in relation to inferred uncertainty in the optimized flux estimates in order to gauge our current ability to close the water budget within an expected uncertainty range.

  11. Effect of post annealing temperatures on microstructures and mechanical properties of cryorolled 5052 aluminium sheet alloy

    Science.gov (United States)

    Anas, N. M.; Umar, Z. A. A.; Zuhailawati, H.; Anasyida, A. S.

    2017-07-01

    The effect of post annealing temperature of cryorolled 5052 Al alloy after cryorolling process at 30% thickness reduction was investigated, focusing on the evolution of microstructures and mechanical properties. The evolution of microstructure was investigated using optical microscopy (OM). The mechanical behaviour of the samples have been evaluated through Vickers hardness and tensile test performed at room temperature. The results showed that the post annealing on cryorolled 5052 Al alloy have enhanced the ductility with sacrificing the hardness and strength. The lattice strain of post annealed 5052 Al alloy decreased with increasing of annealing temperatures. The evolution of microstructure of the post annealed 5052 Al alloy showed equiaxed grains at 200°C and grain coarsening as post annealing temperature increases to 350°C. The result of crystallite size confirmed the grain size increased as the post annealing temperature rises.

  12. Retrieval of Surface and Subsurface Moisture of Bare Soil Using Simulated Annealing

    Science.gov (United States)

    Tabatabaeenejad, A.; Moghaddam, M.

    2009-12-01

    Soil moisture is of fundamental importance to many hydrological and biological processes. Soil moisture information is vital to understanding the cycling of water, energy, and carbon in the Earth system. Knowledge of soil moisture is critical to agencies concerned with weather and climate, runoff potential and flood control, soil erosion, reservoir management, water quality, agricultural productivity, drought monitoring, and human health. The need to monitor the soil moisture on a global scale has motivated missions such as Soil Moisture Active and Passive (SMAP) [1]. Rough surface scattering models and remote sensing retrieval algorithms are essential in study of the soil moisture, because soil can be represented as a rough surface structure. Effects of soil moisture on the backscattered field have been studied since the 1960s, but soil moisture estimation remains a challenging problem and there is still a need for more accurate and more efficient inversion algorithms. It has been shown that the simulated annealing method is a powerful tool for inversion of the model parameters of rough surface structures [2]. The sensitivity of this method to measurement noise has also been investigated assuming a two-layer structure characterized by the layers dielectric constants, layer thickness, and statistical properties of the rough interfaces [2]. However, since the moisture profile varies with depth, it is sometimes necessary to model the rough surface as a layered structure with a rough interface on top and a stratified structure below where each layer is assumed to have a constant volumetric moisture content. In this work, we discretize the soil structure into several layers of constant moisture content to examine the effect of subsurface profile on the backscattering coefficient. We will show that while the moisture profile could vary in deeper layers, these layers do not affect the scattered electromagnetic field significantly. Therefore, we can use just a few layers

  13. Electric power monthly, May 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-05-01

    The Electric Power Monthly (EPM) presents monthly electricity statistics. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. Data in this report are presented for a wide audience including Congress, Federal and State agencies, the electric utility industry, and the general public. This publication provides monthly statistics for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Statistics by company and plant are published on the capability of new generating units, net generation, fuel consumption, fuel stocks, quantity and quality of fuel, and cost of fossil fuels.

  14. Electric power monthly, August 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-08-13

    The Electric Power Monthly (EPM) presents monthly electricity statistics. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. The EPM is prepared by the Survey Management Division; Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), Department of Energy. This publication provides monthly statistics at the US, Census division, and State levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North American Electric Reliability Council (NERC) regions.

  15. Natural gas monthly, April 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-04-01

    This issue of the Natural Gas Monthly presents the most recent estimates of natural gas data from the Energy Information Administration (EIA). Estimates extend through April 1998 for many data series. The report highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, feature articles are presented designed to assist readers in using and interpreting natural gas information. This issue contains the special report, ``Natural Gas 1997: A Preliminary Summary.`` This report provides information on natural gas supply and disposition for the year 1997, based on monthly data through December from EIA surveys. 6 figs., 28 tabs.

  16. Electric power monthly, April 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-04-01

    The Electric Power Monthly (EPM) presents monthly electricity statistics. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. This publication provides monthly statistics at the U.S., Census division, and State levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North American Electric Reliability Council (NERC) regions. This April 1994 issue contains 1993 year-end data and data through January 1994.

  17. Electric power monthly, September 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-17

    The Electric Power Monthly (EPM) presents monthly electricity statistics. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. The EPM is prepared by the Survey Management Division; Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), Department of Energy. This publication provides monthly statistics at the US, Census division, and State levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North American Electric Reliability Council (NERC) regions.

  18. Laser annealing and defect study of chalcogenide photovoltaic materials

    Science.gov (United States)

    Bhatia, Ashish

    Cu(In,Ga)Se2 (CIGSe), CuZnSn(S,Se)4(CZTSSe), etc., are the potential chalcogenide semiconductors being investigated for next-generation thin film photovoltaics (TFPV). While the champion cell efficiency of CIGSe has exceeded 20%, CZTSSe has crossed the 10% mark. This work investigates the effect of laser annealing on CISe films, and compares the electrical characteristics of CIGSe (chalcopyrite) and CZTSe (kesterite) solar cells. Chapter 1 through 3 provide a background on semiconductors and TFPV, properties of chalcopyrite and kesterite materials, and their characterization using deep level transient spectroscopy (DLTS) and thermal admittance spectroscopy (TAS). Chapter 4 investigates electrochemical deposition (nonvacuum synthesis) of CISe followed by continuous wave laser annealing (CWLA) using a 1064 nm laser. It is found that CWLA at ≈ 50 W/cm2 results in structural changes without melting and dewetting of the films. While Cu-poor samples show about 40% reduction in the full width at half maximum of the respective x-ray diffraction peaks, identically treated Cu-rich samples register more than 80% reduction. This study demonstrates that an entirely solid-phase laser annealing path exists for chalcopyrite phase formation and crystallization. Chapter 5 investigates the changes in defect populations after pulse laser annealing in submelting regime of electrochemically deposited and furnace annealed CISe films. DLTS on Schottky diodes reveal that the ionization energy of the dominant majority carrier defect state changes nonmonotonically from 215+/-10 meV for the reference sample, to 330+/-10 meV for samples irradiated at 20 and 30 mJ/cm2, and then back to 215+/-10 meV for samples irradiated at 40 mJ/cm2. A hypothesis involving competing processes of diffusion of Cu and laser-induced generation of In vacancies may explain this behavior. Chapter 6 compares the electrical characteristics of chalcopyrite and kesterite materials. Experiments reveal CZTSe cell has an

  19. Electric power monthly, April 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-05-07

    The Electric Power Monthly is prepared by the Survey Management Division; Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), Department of Energy. This publication provides monthly statistics at the US, Census division, and State levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North American Electric Reliability Council (NERC) regions.

  20. Natural gas monthly, August 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-08-25

    The Natural Gas Monthly (NGM) is prepared in the Data Operations Branch of the Reserves and Natural Gas Division, Office of Oil and Gas, Energy Information Administration (EIA), US Department of Energy (DOE). The NGM highhghts activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information.

  1. Natural gas monthly, March 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. The feature article is entitled ``Natural gas analysis and geographic information systems.`` 6 figs., 27 tabs.

  2. Natural gas monthly, October 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-10-01

    The Natural Gas Monthly (NGM) is prepared in the Data Operations Branch of the Reserves and Natural Gas Division, Office of Oil and Gas, Energy Information Administration (EIA), U.S. Department of Energy (DOE). The NGM highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information.

  3. Natural gas monthly, April 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-06

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. There are two feature articles in this issue: Natural gas 1998: Issues and trends, Executive summary; and Special report: Natural gas 1998: A preliminary summary. 6 figs., 28 tabs.

  4. Electric power monthly, June 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-06-01

    The Electric Power Monthly (EPM) presents monthly electricity statistics. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. Data in this report are presented for a wide audience including Congress, Federal and State agencies, the electric utility industry, and the general public. The EIA collected the information in this report to fulfill its data collection and dissemination responsibilities as specified in the Federal Energy Administration Act of 1974 (Public Law 93-275) as amended.

  5. Monthly energy review, June 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. The MER is intended for use by Members of Congress, Federal and State agencies, energy analysts, and the general public. EIA welcomes suggestions from readers regarding data series in the MER and in other EIA publications. 37 figs., 61 tabs.

  6. Natural gas monthly, April 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-04-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are present3ed each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. The feature article is entitled ``Natural gas pipeline and system expansions.`` 6 figs., 27 tabs.

  7. ULTRAPLATE 30 month management report

    DEFF Research Database (Denmark)

    Jensen, Jens Dahl

    2003-01-01

    In the period from month 24 to month 30 focus has been on the work-package 3 activities concerning optimisation of the newly developed ULTRAPLATE technology towards specific industrial applications. Three main application areas have been pursued: 1) High- speed plating of lead free solder contacts......, 2) electroforming of tools for moulding of low-cost precision polymer devices and 3) deposition of magnetic alloys to be used in new planar micro-devices. Within each of the three studied application areas, the targeted output is a finished demonstrator to show the potential of the new ULTRAPLATE...

  8. Monthly energy review, July 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. The MER is intended for use by Members of Congress, Federal and State agencies, energy analysts, and the general public. EIA welcomes suggestions from readers regarding data series in the MER and in other EIA publications. 37 figs., 75 tabs.

  9. Electric power monthly, August 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-08-24

    The Electric Power Monthly (EPM) presents monthly electricity statistics. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. Data in this report are presented for a wide audience including Congress, Federal and State agencies, the electric utility industry, and the general public. The EIA collected the information in this report to fulfill its data collection and dissemination responsibilities as specified in the Federal Energy Administration Act of 1974 (Public Law 93-275) as amended.

  10. Electric power monthly, May 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-05-25

    The Electric Power Monthly (EPM) is prepared by the Survey Management Division; Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), Department of Energy. This publication provides monthly statistics at the US, Census division, and State levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North American Electric Reliability Council (NERC) regions.

  11. Electric power monthly, July 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-07-29

    The Electric Power Monthly (EPM) presents monthly electricity statistics. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. Data in this report are presented for a wide audience including Congress, Federal and State agencies, the electric utility industry, and the general public. The EIA collected the information in this report to fulfill its data collection and dissemination responsibilities as specified in the Federal Energy Administration Act of 1974 (Public Law 93-275) as amended.

  12. Normalization of sunspot cycles and eigen mode analysis

    Institute of Scientific and Technical Information of China (English)

    徐文耀

    2002-01-01

    The smoothed monthly sunspot numbers of the previous 22 complete sunspot cycles are normalized in time domain, and then an eigen mode analysis is carried out to draw the principle factors (or components) in the cycles. The results show that the main characteristics of the solar cycles can be described fairly well by the first 5 eigen modes. The obtained eigen modes are used to predict the declining phase of cycle 23 on the basis of the data prior to its maximum. The prediction indicates that cycle 23 will last for 127 months to December 2006, with the minimum of 6.2.

  13. Natural gas monthly, August 1990

    Energy Technology Data Exchange (ETDEWEB)

    1990-11-05

    This report highlights activities, events, and analyses of interest to public and private sector oganizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. 33 tabs.

  14. Monthly energy review, January 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-01-01

    This document presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of U.S. production, consumption, trade, stocks, and prices for petroleum,natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal metric conversion factors.

  15. Monthly energy review, July 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-07-01

    This document presents an overview of the recent monthly energy statistics from the Energy Information Administration (EIA). Statistical data covers activities of U.S. production, consumption, trade, stocks, and prices for fossil fuels , nuclear energy, and electricity. Also included are international energy and thermal and metric conversion factors.

  16. Monthly energy review, November 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-11-24

    The Monthly Energy Review gives information on production, distribution, and consumption for various energy sources, e.g. petroleum, natural gas, oil, coal, electricity, and nuclear energy. Some data is also included on international energy sources and supplies, the import of petroleum products into the US and pricing and reserves data (as applicable) for the various sources of energy listed above.

  17. Monthly energy review, November 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    This document presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. International energy and thermal and metric conversion factors are included.

  18. Monthly energy review, April 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-04-01

    This report presents an overview of monthly energy statistics. The statistics cover the major activities of U.S. production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. International energy and thermal metric conversion factors are included.

  19. Monthly energy review, October 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-26

    The Monthly Energy Review gives information on production, distribution, and consumption for various energy sources, e.g. petroleum, natural gas, oil, coal, electricity, and nuclear energy. Some data is also included on international energy sources and supplies, the import of petroleum products into the US and pricing and reserves data (as applicable) for the various sources of energy listed above.

  20. Monthly energy review, June 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-06-25

    The Monthly Energy Review provides an overview of the production, distribution, and consumption of energy derived from petroleum, natural gas, coal, electricity, and nuclear energy. It also discusses oil and gas resource development, energy prices, and issues relevant to international energy markets.

  1. Periodic progress report, 12 months

    DEFF Research Database (Denmark)

    Juhl, Thomas Winther; Nielsen, Jakob Skov

    The work performed during the first 12 months of the project started with the establishment of the cutting theory for the cutting of heavy sections (phase 1). Phase 2 comprises the design of the first laboratory version cutting head with optics, nozzle systems and interfaces for the various...

  2. Monthly energy review, April 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-04-01

    The Monthly Energy Review contains statistical data on the following: energy consumption, petroleum, natural gas, oil and gas resource development, coal, electricity, nuclear energy, energy prices, and international energy. In addition, an energy overview is provided, and, for the April issue, Energy use and carbon emissions; Some international comparisons.

  3. Hepatitis Awareness Month PSA (:30)

    Centers for Disease Control (CDC) Podcasts

    2011-05-11

    May is National Hepatitis Awareness Month. This 30 second PSA discusses hepatitis and encourages listners to talk to their health care professional about getting tested.  Created: 5/11/2011 by National Center for HIV/AIDS, Viral Hepatitis, STD, and TB Prevention.   Date Released: 5/11/2011.

  4. Prediction of Malaysian monthly GDP

    Science.gov (United States)

    Hin, Pooi Ah; Ching, Soo Huei; Yeing, Pan Wei

    2015-12-01

    The paper attempts to use a method based on multivariate power-normal distribution to predict the Malaysian Gross Domestic Product next month. Letting r(t) be the vector consisting of the month-t values on m selected macroeconomic variables, and GDP, we model the month-(t+1) GDP to be dependent on the present and l-1 past values r(t), r(t-1),…,r(t-l+1) via a conditional distribution which is derived from a [(m+1)l+1]-dimensional power-normal distribution. The 100(α/2)% and 100(1-α/2)% points of the conditional distribution may be used to form an out-of sample prediction interval. This interval together with the mean of the conditional distribution may be used to predict the month-(t+1) GDP. The mean absolute percentage error (MAPE), estimated coverage probability and average length of the prediction interval are used as the criterions for selecting the suitable lag value l-1 and the subset from a pool of 17 macroeconomic variables. It is found that the relatively better models would be those of which 2 ≤ l ≤ 3, and involving one or two of the macroeconomic variables given by Market Indicative Yield, Oil Prices, Exchange Rate and Import Trade.

  5. Monthly energy review, March 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-03-29

    The Monthly Energy Review provides information on production, distribution, consumption, prices, imports, and exports for the following US energy sources: petroleum; petroleum products; natural gas; coal; electricity; and nuclear energy. The section on international energy contains data for world crude oil production and consumption, petroleum stocks in OECD countries, and nuclear electricity gross generation.

  6. Monthly energy review, December 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-22

    This document provides data on monthly energy use and fossil fuels. The following sections are included: Highlights: Emissions of greenhouse gases in the United States 1985--1990; Highlights: assessment of energy use in multibuilding facilities; energy overview; energy consumption; petroleum; natural gas; oil and gas resource development; coal; electricity; nuclear energy; energy prices; and international energy.

  7. Periodic progress report, 12 months

    DEFF Research Database (Denmark)

    Juhl, Thomas Winther; Nielsen, Jakob Skov

    The work performed during the first 12 months of the project started with the establishment of the cutting theory for the cutting of heavy sections (phase 1). Phase 2 comprises the design of the first laboratory version cutting head with optics, nozzle systems and interfaces for the various machi...

  8. Monthly energy review, October 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-26

    The Monthly Energy Review gives information on production, distribution, and consumption for various energy sources, e.g. petroleum, natural gas, oil, coal, electricity, and nuclear energy. Some data is also included on international energy sources and supplies, the import of petroleum products into the US and pricing and reserves data (as applicable) for the various sources of energy listed above.

  9. Monthly energy review, June 1990

    Energy Technology Data Exchange (ETDEWEB)

    1990-09-26

    The Monthly Energy Review presents current data on production, consumption, stocks, imports, exports, and prices of the principal energy commodities in the United States. Also included are data on international production of crude oil, consumption of petroleum products, petroleum stocks, and production of electricity from nuclear-powered facilities.

  10. Your Child's Development: 1 Month

    Science.gov (United States)

    ... Child Too Busy? Helping Your Child Adjust to Preschool School Lunches Kids and Food: 10 Tips for Parents Healthy Habits for TV, Video Games, and the Internet Your Child’s Development: 1 Month KidsHealth > For Parents > Your Child’s Development: ...

  11. Electric Power Monthly, July 1990

    Energy Technology Data Exchange (ETDEWEB)

    1990-10-12

    The Electric Power Monthly (EPM) is prepared by the Electric Power Division; Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), Department of Energy. This publication provides monthly statistics at the national, Census division, and State levels for net generation, fuel consumption, fuel stocks, quantity and quality of fuel, cost of fuel, electricity sales, and average revenue per kilowatthour of electricity sold. Data on net generation are also displayed at the North American Electric Reliability Council (NERC) region level. Additionally, company and plant level information are published in the EPM on capability of new plants, net generation, fuel consumption, fuel stocks, quantity and quality of fuel, and cost in fuel. Quantity, quality, and cost of fuel data lag the net generation, fuel consumption, fuel stocks, electricity sales, and average revenue per kilowatthour data by 1 month. This difference in reporting appears in the national, Census division, and State level tables. However, at the plant level, all statistics presented are for the earlier month for the purpose of comparison. 12 refs., 4 figs., 48 tabs.

  12. Electric power monthly, March 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-20

    This report for March 1995, presents monthly electricity statistics for a wide audience including Congress, Federal and State agencies, the electric utility industry, and the general public. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead.

  13. Natural gas monthly, July 1990

    Energy Technology Data Exchange (ETDEWEB)

    1990-10-03

    This report highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. A glossary is included. 7 figs., 33 tabs.

  14. STD Awareness Month PSA (:30)

    Centers for Disease Control (CDC) Podcasts

    2011-04-19

    April is National STD Awareness Month. STDs can affect anyone. Many STDs don't have symptoms so it's important to get tested.  Created: 4/19/2011 by National Center for HIV/AIDS, Viral Hepatitis, STD, and TB Prevention.   Date Released: 4/19/2011.

  15. Tritium release from neutron irradiated beryllium: Kinetics, long-time annealing and effect or crack formation

    Energy Technology Data Exchange (ETDEWEB)

    Scaffidi-Argentina, F.; Werle, H. [Forschungszentrum Karlsruhe, (Germany)

    1995-09-01

    Since beryllium is considered as one of the best neutron multiplier materials in the blanket of the next generation fusion reactors, several studies have been started to evaluate its behaviour under irradiation during both operating and accidental conditions. Based on safety considerations, tritium produced in beryllium during neutron irradiation represents one important issue, therefore it is necessary to investigate tritium transport processes by using a comprehensive mathematical model and comparing its predictions with well characterized experimental tests. Because of the difficulties in extrapolating the short-time tritium release tests to a longer time scale, also long-time annealing experiments with beryllium samples from the SIBELIUS irradiation. have been carried out at the Forschungszentrum Karlsruhe. Samples were annealed up to 12 months at temperatures up to 650{degrees}C. The inventory after annealing was determined by heating the samples up to 1050{degrees}C with a He+0.1 vo1% H{sub 2} purge gas. Furthermore, in order to investigate the likely effects of cracks formation eventually causing a faster tritium release from beryllium, the behaviour of samples irradiated at low temperature (40-50{degrees}C) but up to very high fast neutron fluences (0.8-3.9{center_dot}10{sup 22} cm{sup -2}, E{sub n}{ge}1 MeV) in the BR2 reactor has been investigated. Tritium was released by heating the beryllium samples up to 1050{degrees}C and purging them with He+0.1 vo1% H{sub 2}. Tritium release from high-irradiated beryllium samples showed a much faster kinetics than from the low-irradiated ones, probably because of crack formation caused by thermal stresses in the brittle material and/or by helium bubbles migration. The obtained experimental data have been compared with predictions of the code ANFIBE with the goal to better understand the physical mechanisms governing tritium behaviour in beryllium and to assess the prediction capabilities of the code.

  16. Your Child's Development: 1 Year (12 Months)

    Science.gov (United States)

    ... Kids For Parents MORE ON THIS TOPIC Your Child's Checkup: 1 Year (12 Months) Your Baby's Growth: 12 Months Your Baby's Hearing, Vision, and Other Senses: 12 Months Sleep and Your 8- to 12-Month-Old Growth ...

  17. Predicting the start and maximum amplitude of solar cycle 24 using similar phases and a cycle grouping

    Institute of Scientific and Technical Information of China (English)

    Jia-Long Wang; Wei-Guo Zong; Gui-Ming Le; Hai-Juan Zhao; Yun-Qiu Tang; Yang Zhang

    2009-01-01

    We find that the solar cycles 9, 11, and 20 are similar to cycle 23 in their respective descending phases. Using this similarity and the observed data of smoothed monthly mean sunspot numbers (SMSNs) available for the descending phase of cycle 23, we make a date calibration for the average time sequence made of the three descending phases of the three cycles, and predict the start of March or April 2008 for cycle 24. For the three cycles, we also find a linear correlation of the length of the descending phase of a cycle with the difference between the maximum epoch of this cycle and that of its next cycle.Using this relationship along with the known relationship between the rise-time and the maximum amplitude of a slowly rising solar cycle, we predict the maximum SMSN of cycle 24 of 100.2±7.5 to appear during the period from May to October 2012.

  18. Petroleum supply monthly, March 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-03-30

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas -- the United States (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided from other sources.

  19. Petroleum supply monthly, June 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-06-28

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures ih the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas - - the United States (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided firom other sources.

  20. Electric power monthly, July 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-07-01

    The Electric Power Monthly (EPM) presents monthly electricity statistics. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. Data in this report are presented for a wide audience including Congress, Federal and State agencies, the electric utility industry, and the general public. The EIA collected the information in this report to fulfill its data collection and dissemination responsibilities as specified in the Federal Energy Administration Act of 1974 (Public Law 93-275) as amended. The EPM is prepared by the Survey Management Division; Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), Department of Energy. This publication provides monthly statistics at the US, Census division, and State levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North American Electric Reliability Council (NERC) regions. Statistics by company and plant are published in the EPM on the capability of new generating units, net generation, fuel consumption, fuel stocks, quantity and quality of fuel, and cost of fossil fuels. Data on quantity, quality, and cost of fossil fuels lag data on net generation, fuel consumption, fuel stocks, electricity sales, and average revenue per kilowatthour by 1 month. This difference in reporting appears in the US, Census division, and State level tables. However, for purposes of comparison, plant-level data are presented for the earlier month.

  1. Duean sip, théâtre de l’ethnorégionalisme sud. Les nomades de la mer et le cycle rituel du dixième mois dans la province de Phang Nga (sud de la Thaïlande Duean sip, Theater of the Southern Ethnoregionalism. The Sea Nomads and the Tenth Lunar Month Ritual Complex in the Phang Nga Province (Southern Thailand

    Directory of Open Access Journals (Sweden)

    Olivier Ferrari

    2012-11-01

    Full Text Available La cérémonie bouddhique du dixième mois lunaire, connue comme la fête des morts et des revenants, revêt dans la région de Phang Nga, au sud de la Thaïlande une importance et un rôle qui vont bien au-delà de sa signification religieuse. Il s’agit en effet d’un complexe rituel qui, en s’emboîtant avec les cérémonies du festival végétarien des Sino-Thaïs et avec d’autres cérémonies propres aux nomades de la mer (Moken, Moklen et Urak Lawoi, met en scène les fondements des relations interethniques qui caractérisent la région. Le partage du territoire et des rôles sociaux dans celui-ci sont au cœur de ce cycle rituel, qui devient de fait le théatre de l’ethnorégionalisme du sud de la Thaïlande.The bouddhist ceremony of the tenth lunar month, dedicated to the dead and the hungry ghosts, is a paramount feature in the region of Phang Nga, Southern Thailand. Its importance and role go well beyond its religious meaning. Indeed, it is a ritual ensemble which, by overlapping with the vegetarien festival of the Sino-Thais and with ceremonises held by the Sea Gypsies (Moken, Moklen and Urak Lawoi, displays the very foundations of the interethnic relationships that characterize the region. The sharing of the territory and of the social roles distributed within the region are the core of the ritual cycle, which is thus the theater of Southern Thai’s ethnoregionalism.

  2. Acid hydrolysis of native and annealed starches and branch-structure of their Naegeli dextrins.

    Science.gov (United States)

    Nakazawa, Yuta; Wang, Ya-Jane

    2003-11-21

    Eight commercial starches, including common corn, waxy corn, wheat, tapioca, potato, Hylon V, Hylon VII, and mung bean starch, were annealed by a multiple-step process, and their gelatinization characteristics were determined. Annealed starches had higher gelatinization temperatures, reduced gelatinization ranges, and increased gelatinization enthalpies than their native starches. The annealed starches with the highest gelatinization enthalpies were subjected to acid hydrolysis with 15.3% H2SO4, and Naegeli dextrins were prepared after 10 days' hydrolysis. Annealing increased the acid susceptibility of native starches in the first (rapid) and the second (slow) phases with potato starch showing the greatest and high amylose starches showing the least changes. Starches with a larger shift in onset gelatinization temperature also displayed a greater percent hydrolysis. The increase in susceptibility to acid hydrolysis was proposed to result from defective and porous structures that resulted after annealing. Although annealing perfected the crystalline structure, it also produced void space, which led to porous structures and possible starch granule defects. The molecular size distribution and chain length distribution of Naegeli dextrins of annealed and native starches were analyzed. The reorganization of the starch molecule during annealing occurred mainly within the crystalline lamellae. Imperfect double helices in the crystalline lamellae improved after annealing, and the branch linkages at the imperfect double helices became protected by the improved crystalline structure. Therefore, more long chains were observed in the Naegeli dextrins of annealed starches than in native starches.

  3. Effect of annealing in hydrogen atmosphere on ZnO films for field emission display

    Science.gov (United States)

    Zulkifli, Zurita; Sharma, Subash; Shinde, Sachin; Kalita, Golap; Tanemura, M.

    2015-11-01

    Surface morphology, crystallinity, conductivity and optical transmittance of ZnO films can be modified by annealing process. Hydrogen is one of the popular annealing gases as well as nitrogen, argon, oxygen and air which are commonly used for thin film cleaning or the removal of native oxide. In general, annealing is done at high temperatures (> 600degC) to improve the film properties. From a view point of environment, however, lower annealing temperature is preferable. In this work, low annealing process was challenged to understand the effect of annealing temperature on properties of ZnO thin films and nanostructured film grown on glass substrates for transparent field emission device applications. The annealing temperature employed was 100, 200 and 450°C at 100 sccm hydrogen flow rate. ZnO thin films were deposited by RF magnetron sputtering. The ZnO thin films were characterized by X-ray diffraction analysis (XRD), Atomic Force Microscopy (AFM), UV-VIS and Raman spectroscopy. The sheet resistances reduced about 15 kohm/sq at low annealing temperature. By contrast, the optical transmittance did not show any significant changes after annealing. The FE current density increased after the ZnO nanostructures film was annealed in 100°C. The results obtained could motivate a surface treatment for flexible ZnO thin film since the substrate is always suffered by heat.

  4. MICROSTRUCTURE AND PROPERTIES OF ANNEALED ZnO THIN FILMS DEPOSITED BY MAGNETRON SPUTTERING

    Institute of Scientific and Technical Information of China (English)

    J. Lee; W. Gao; Z. Li; M. Hodgson; A. Asadov; J. Metson

    2005-01-01

    ZnO thin films were deposited on a glass substrate by dc (direct current) and rf (radio frequency) magnetron sputtering. Post-deposition annealing was performed in different atmospheres and at different temperatures. The correlation of the annealing conditions with the microstructure and properties of the ZnO films were investigated by ultraviolet-visible spectroscopy, X-ray diffraction, conductivity measurement and scanning electron microscopy. Only the strong 002peak could be observed by X-ray diffraction. The post-deposition annealing of ZnO films was found to alter the film's microstructure and properties, including crystallinity, porosity, grain size, internal stress level and resistivity. It was also found that after annealing, the conductivity of poorly conductive samples often improved. However, annealing does not improve the conductivity of samples with high conductivity prior to annealing. The resistivity of as-grown films annealing on the conductivity of ZnO, it is believed that annealing may alter the presence and distribution of oxygen defects, reduce the lattice stress, cause diffusion, grain coarsening and recrystallization. Annealing will reduce the density of grain boundaries in less dense films,which may decrease the resistivity of the films. On the other hand, annealing may also increase the porosity of thin films, leading to an increase in resistivity.

  5. Formation of oxygen related donors in step-annealed CZ–silicon

    Indian Academy of Sciences (India)

    Vikash Dubey; Shyam Singh

    2002-12-01

    The effect of step-annealing necessitated by the difficulties being faced in the long duration annealing treatments to be given to CZ–silicon has been studied. One pre-anneal of 10 h followed by annealing of 10 h causes a decrease in the absorption coefficient for carbon (c). Oxygen and carbon both accelerate thermal donor (TD) formation process but oxygen plays a dominating role. Three anneals of 10 h each followed by one anneal of 10 h support the view that carbon suppresses the donor formation. The absorption coefficient for carbon decreases after a few number of step-anneals resulting in the transformation of TD to new donor (ND) as brought about by annealing at temperature, > 500°C. It is quite logical to conclude that step-annealing may bring about the same results as obtained on continuous annealing for a longer duration. The results have been fully supported by proper interpretation in the light of existing theories.

  6. Bipolar mood cycles and lunar tidal cycles.

    Science.gov (United States)

    Wehr, T A

    2017-01-24

    In 17 patients with rapid cycling bipolar disorder, time-series analyses detected synchronies between mood cycles and three lunar cycles that modulate the amplitude of the moon's semi-diurnal gravimetric tides: the 14.8-day spring-neap cycle, the 13.7-day declination cycle and the 206-day cycle of perigee-syzygies ('supermoons'). The analyses also revealed shifts among 1:2, 1:3, 2:3 and other modes of coupling of mood cycles to the two bi-weekly lunar cycles. These shifts appear to be responses to the conflicting demands of the mood cycles' being entrained simultaneously to two different bi-weekly lunar cycles with slightly different periods. Measurements of circadian rhythms in body temperature suggest a biological mechanism through which transits of one of the moon's semi-diurnal gravimetric tides might have driven the patients' bipolar cycles, by periodically entraining the circadian pacemaker to its 24.84-h rhythm and altering the pacemaker's phase-relationship to sleep in a manner that is known to cause switches from depression to mania.Molecular Psychiatry advance online publication, 24 January 2017; doi:10.1038/mp.2016.263.

  7. Natural Gas Monthly August 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-08-01

    The Natural Gas Monthly (NGM) highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. From time to time, the NGM features articles designed to assist readers in using and interpreting natural gas information. Explanatory notes supplement the information found in tables of the report. A description of the data collection surveys that support the NGM is provided. A glossary of the terms used in this report is also provided to assist readers in understanding the data presented in this publication.

  8. Natural gas monthly, August 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    This analysis presents the most recent data on natural gas prices, supply, and consumption from the Energy Information Administration (EIA). The presentation of the latest monthly data is followed by an update on natural gas markets. The markets section examines the behavior of daily spot and futures prices based on information from trade press, as well as regional, weekly data on natural gas storage from the American Gas Association (AGA). This {open_quotes}Highlights{close_quotes} closes with a special section comparing and contrasting EIA and AGA storage data on a monthly and regional basis. The regions used are those defined by the AGA for their weekly data collection effort: the Producing Region, the Consuming Region East, and the Consuming Region West. While data on working gas levels have tracked fairly closely between the two data sources, differences have developed recently. The largest difference is in estimates of working gas levels in the East consuming region during the heating season.

  9. Monthly energy review, March 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of U.S. production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. Energy production during December 1997 totaled 5.9 quadrillion Btu, a 2.8 percent increase from the level of production during December 1996. Coal production increased 9.5 percent, natural gas production increased 3.9 percent, and production of crude oil and natural gas plant liquids decreased 1.1 percent. All other forms of energy production combined were down 6.9 percent from the level of production during December 1996.

  10. Natural gas monthly, October 1991

    Energy Technology Data Exchange (ETDEWEB)

    1991-11-05

    The Natural Gas Monthly (NGM) is prepared in the Data Operations Branch of the Reserves and Natural Gas Division, Office of Oil and Gas, Energy Information Administration (EIA), US Department of Energy (DOE). The NGM highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. The data in this publication are collected on surveys conducted by the EIA to fulfill its responsibilities for gathering and reporting energy data. Some of the data are collected under the authority of the Federal Energy Regulatory Commission (FERC), an independent commission within the DOE, which has jurisdiction primarily in the regulation of electric utilities and the interstate natural gas industry. Geographic coverage is the 50 States and the District of Columbia. 16 figs., 33 tabs.

  11. Petroleum marketing monthly, September 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-09-01

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum product sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

  12. Petroleum marketing monthly, June 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-06-01

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in five sections: Summary Statistics; Crude Oil Prices; Prices of Petroleum Products; Volumes of Petroleum Products; and Prime Supplier Sales Volumes of Petroleum Products for Local Consumption. The feature article is entitled ``The Second Oxygenated Gasoline Season.`` 7 figs., 50 tabs.

  13. Natural gas monthly, February 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-25

    The NGM highlights activities, events, and analyses of interest to public and private sector organizations associated with the natural gas industry. Volume and price data are presented each month for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. The NGM also features articles designed to assist readers in using and interpreting natural gas information.

  14. Monthly energy review, October 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    This document presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of U.S. production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Information is also provided for oil and gas resource development. International energy statistics are given for petroleum production, consumption, and stocks, and for nuclear electricity gross generation. 37 figs., 61 tabs.

  15. Laser fusion monthly -- August 1980

    Energy Technology Data Exchange (ETDEWEB)

    Ahlstrom, H.G. [ed.

    1980-08-01

    This report documents the monthly progress for the laser fusion research at Lawrence Livermore National Laboratory. First it gives facilities report for both the Shiva and Argus projects. Topics discussed include; laser system for the Nova Project; the fusion experiments analysis facility; optical/x-ray streak camera; Shiva Dante System temporal response; 2{omega}{sub 0} experiment; and planning for an ICF engineering test facility.

  16. Introducing 'Image of the Month'

    Science.gov (United States)

    Brian, Jones

    2016-04-01

    The Editors of Sedimentary Geology are pleased to announce the establishment of an 'Image of the Month', to appear in each issue of the journal. The idea is to publish outstanding examples of sedimentary features, at all scales, as a means of increasing their visibility and so promoting further discussion and exchange of ideas within the community. The image could be at the scale of satellite image, aerial photograph, outcrop, specimen or thin section.

  17. Monthly energy review, December 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-21

    This publication presents an overview of EIA`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. An energy preview of alternative fuel providers vehicle fleet surveys is included. The publication is intended for use by members of Congress, Federal and State agencies, energy analysts, and the general public.

  18. Electric power monthly, May 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-01

    This publication presents monthly electricity statistics for a wide audience including Congress, Federal and Stage agencies, the electric utility industry, and the general public. Purpose is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. EIA collected the information to fulfill its data collection and dissemination responsibilities in Federal Energy Administration Act of 1974 (Public Law 93-275) as amended.

  19. Electric Power monthly, November 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-11-01

    This publication presents monthly electricity statistics for a wide audience including Congress, Federal and state agencies, the electric utility industry, and the general public. Purpose is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. EIA collected the information in this report to fulfill its data collection and dissemination responsibilities as specified in the Federal Energy Administration Act of 1974 (Public Law 93-275) as amended.

  20. Natural gas monthly, March 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The March 1998 edition of the Natural Gas Monthly highlights activities, events, and analyses associated with the natural gas industry. Volume and price data are presented for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. This report also features an article on the correction of errors in the drilling activity estimates series, and in-depth drilling activity data. 6 figs., 28 tabs.

  1. Natural gas monthly, March 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The March 1998 edition of the Natural Gas Monthly highlights activities, events, and analyses associated with the natural gas industry. Volume and price data are presented for natural gas production, distribution, consumption, and interstate pipeline activities. Producer-related activities and underground storage data are also reported. This report also features an article on the correction of errors in the drilling activity estimates series, and in-depth drilling activity data. 6 figs., 28 tabs.

  2. Electric power monthly, October 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-20

    The Electric Power Monthly (EPM) presents monthly electricity statistics. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. Data in this report are presented for a wide audience including Congress, Federal and State agencies, the electric utility industry, and the general public. The EIA collected the information in this report to fulfill its data collection and dissemination responsibilities as specified in the Federal Energy Administration Act of 1974 (Public Law 93-275) as amended. This publication provides monthly statistics at the US, Census division, and State levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North American Electric Reliability Council (NERC) regions. Statistics by company and plant are published in the EPM on the capability of new generating units, net generation, fuel consumption, fuel stocks, quantity and quality of fuel, and cost of fossil fuels.

  3. Natural gas monthly, March 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This issue of the Natural Gas Monthly contains estimates for March 1999 for many natural gas data series at the national level. Estimates of national natural gas prices are available through December 1998 for most series. Highlights of the data contained in this issue are listed below. Preliminary data indicate that the national average wellhead price for 1998 declined to 16% from the previous year ($1.96 compared to $2.32 per thousand cubic feet). At the end of March, the end of the 1998--1999 heating season, the level of working gas in underground natural gas storage facilities is estimated to be 1,354 billion cubic feet, 169 billion cubic feet higher than at the end of March 1998. Gas consumption during the first 3 months of 1999 is estimated to have been 179 billion cubic feet higher than in the same period in 1998. Most of this increase (133 billion cubic feet) occurred in the residential sector due to the cooler temperatures in January and February compared to the same months last year. According to the National Weather Service, heating degree days in January 1999 were 15% greater than the previous year while February recorded a 5% increase.

  4. Electric power monthly, February 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-16

    The Electric Power Monthly (EMP) presents monthly electricity statistics. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. Data in this report are presented for a wide audience including Congress, Federal and State agencies, the electric utility industry, and the general public. The EIA collected the information in this report to fulfill its data collection and dissemination responsibilities as specified in the Federal Energy Administration Act of 1974 (Public Law 93-275) as amended. This publication provides monthly statistics at the US, Census division, and State levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North American Electric Reliability Council (NERC) regions. Statistics by company and plant are published in the EPM on the capability of new generating units, net generation, fuel consumption, fuel stocks, quantity and quality of fuel, and cost of fossil fuels.

  5. Electric power monthly, January 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-26

    The Electric Power Monthly (EPM) presents monthly electricity statistics. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. Data in this report are presented for a wide audience including Congress, Federal and State agencies, the electric utility industry, and the general public. The EIA collected the information in this report to fulfill its data collection and dissemination responsibilities as specified in the Federal Energy Administration Act of 1974 (Public Law 93-275) as amended. This publication provides monthly statistics at the US Census division, and State levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North American Electric Reliability Council (NERC) regions. Statistics by company and plant are published in the EPM on the capability of new generating units, net generation, fuel consumption, fuel stocks, quantity and quality of fuel, and cost of fossil fuels.

  6. Electric Power Monthly, June 1990

    Energy Technology Data Exchange (ETDEWEB)

    1990-09-13

    The EPM is prepared by the Electric Power Division; Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), Department of Energy. This publication provides monthly statistics at the national, Census division, and State levels for net generation, fuel consumption, fuel stocks, quantity and quality of fuel, electricity sales, and average revenue per kilowatthour of electricity sold. Data on net generation are also displayed at the North American Electric Reliability Council (NERC) region level. Additionally, company and plant level information are published in the EPM on capability of new plants, net generation, fuel consumption, fuel stocks, quantity and quality of fuel, and cost of fuel. Quantity, quality, and cost of fuel data lag the net generation, fuel consumption, fuel stocks, electricity sales, and average revenue per kilowatthour data by 1 month. This difference in reporting appears in the national, Census division, and State level tables. However, at the plant level, all statistics presented are for the earlier month for the purpose of comparison. 40 tabs.

  7. Annealing behaviour of MeV erbium implanted lithium niobate

    Energy Technology Data Exchange (ETDEWEB)

    Gortmaker, P.; McCallum, J.C. [Royal Melbourne Inst. of Tech., VIC (Australia)

    1993-12-31

    Lithium niobate (LiNbO{sub 3}) is a crystalline ceramic commonly used in the fabrication of optoelectronic devices. Recently, rare earth doping of LiNbO{sub 3} has become a topic of particular interest. The electronic configuration of rare earth elements such as Erbium (Er) and Neodymium (Nd) allows them to lase in nearly any host matrix making fabrication of a whole range of new optoelectronic devices possible. At present, the doping technique, for LiNbO{sub 3} are centred upon diffusion technology, but the diffusion profiles for the rare earths are not generally well-matched to the optical modes of the device. The aim of this research is to develop MeV implantation and annealing conditions of rare earth doped LiNbO{sub 3} that would be compatible with optoelectronic device fabrication. To determine the characteristics of the rare earth elements in the LiNbO{sub 3} host material over the depth range of interest in optoelectronic device applications, high energy Rutherford backscattering spectrometry and ion channeling (RBS-C) must be used. Presented here are the Er depth profile and lattice damage results obtained from 5 MeV RBS-C measurements on samples of LiNbO{sub 3} implanted with various doses of MeV Erbium and subsequently thermally annealed at a temperature of 1000 deg C. It was found that there is a peak implant concentration (2 x 10{sup 16} Er/cm{sup 2}) for which erbium no longer goes substitutional in the lattice, and the implantation damage is not fully removed by annealing. 8 refs., 3 figs.

  8. Reduced-Complexity Deterministic Annealing for Vector Quantizer Design

    Directory of Open Access Journals (Sweden)

    Ortega Antonio

    2005-01-01

    Full Text Available This paper presents a reduced-complexity deterministic annealing (DA approach for vector quantizer (VQ design by using soft information processing with simplified assignment measures. Low-complexity distributions are designed to mimic the Gibbs distribution, where the latter is the optimal distribution used in the standard DA method. These low-complexity distributions are simple enough to facilitate fast computation, but at the same time they can closely approximate the Gibbs distribution to result in near-optimal performance. We have also derived the theoretical performance loss at a given system entropy due to using the simple soft measures instead of the optimal Gibbs measure. We use thederived result to obtain optimal annealing schedules for the simple soft measures that approximate the annealing schedule for the optimal Gibbs distribution. The proposed reduced-complexity DA algorithms have significantly improved the quality of the final codebooks compared to the generalized Lloyd algorithm and standard stochastic relaxation techniques, both with and without the pairwise nearest neighbor (PNN codebook initialization. The proposed algorithms are able to evade the local minima and the results show that they are not sensitive to the choice of the initial codebook. Compared to the standard DA approach, the reduced-complexity DA algorithms can operate over 100 times faster with negligible performance difference. For example, for the design of a 16-dimensional vector quantizer having a rate of 0.4375 bit/sample for Gaussian source, the standard DA algorithm achieved 3.60 dB performance in 16 483 CPU seconds, whereas the reduced-complexity DA algorithm achieved the same performance in 136 CPU seconds. Other than VQ design, the DA techniques are applicable to problems such as classification, clustering, and resource allocation.

  9. Estimation of the parameters of ETAS models by Simulated Annealing

    Science.gov (United States)

    Lombardi, Anna Maria

    2015-02-01

    This paper proposes a new algorithm to estimate the maximum likelihood parameters of an Epidemic Type Aftershock Sequences (ETAS) model. It is based on Simulated Annealing, a versatile method that solves problems of global optimization and ensures convergence to a global optimum. The procedure is tested on both simulated and real catalogs. The main conclusion is that the method performs poorly as the size of the catalog decreases because the effect of the correlation of the ETAS parameters is more significant. These results give new insights into the ETAS model and the efficiency of the maximum-likelihood method within this context.

  10. Simulated annealing approach to the max cut problem

    Science.gov (United States)

    Sen, Sandip

    1993-03-01

    In this paper we address the problem of partitioning the nodes of a random graph into two sets, so as to maximize the sum of the weights on the edges connecting nodes belonging to different sets. This problem has important real-life counterparts, but has been proven to be NP-complete. As such, a number of heuristic solution techniques have been proposed in literature to address this problem. We propose a stochastic optimization technique, simulated annealing, to find solutions for the max cut problem. Our experiments verify that good solutions to the problem can be found using this algorithm in a reasonable amount of time.

  11. Skymapping with OSSE via the Mean Field Annealing Pixon Technique

    CERN Document Server

    Dixon, D D; Zych, A D; Cheng, L X; Johnson, W N; Kurfess, J D; Pina, R K; Pütter, R C; Purcell, W R; Wheaton, W A; Wheaton, Wm. A.

    1997-01-01

    We present progress toward using scanned OSSE observations for mapping and sky survey work. To this end, we have developed a technique for detecting pointlike sources of unknown number and location, given that they appear in a background which is relatively featureless or which can be modeled. The technique, based on the newly developed concept and mean field annealing, is described, with sample reconstructions of data from the OSSE Virgo Survey. The results demonstrate the capability of reconstructing source information without any a priori information about the number and/or location of pointlike sources in the field-of-view.

  12. Laser annealing of thin film polycrystalline silicon solar cell

    Directory of Open Access Journals (Sweden)

    Chowdhury A.

    2013-11-01

    Full Text Available Performances of thin film polycrystalline silicon solar cell grown on glass substrate, using solid phase crystallization of amorphous silicon can be limited by low dopant activation and high density of defects. Here, we investigate line shaped laser induced thermal annealing to passivate some of these defects in the sub-melt regime. Effect of laser power and scan speed on the open circuit voltage of the polysilicon solar cells is reported. The processing temperature was measured by thermal imaging camera. Enhancement of the open circuit voltage as high as 210% is achieved using this method. The results are discussed.

  13. Annealed Demon Algorithms Solving the Environmental / Economic Dispatch Problem

    Directory of Open Access Journals (Sweden)

    Aristidis VLACHOS

    2013-06-01

    Full Text Available This paper presents an efficient and reliable Annealed Demon (AD algorithm for the Environmental/Economic Dispatch (EEB problem. The EED problem is a multi-objective non-linear optimization problem with constraints. This problem is one of the fundamentals issues in power system operation. The system of generation associates thermal generators and emissions which involves sulphur oxides (SO2 and nitrogen oxides (NOx. The aim is to minimize total fuel cost of the system and control emission. The proposed AD algorithm is applied for EED of a simple power system.

  14. Global annealing genetic algorithm and its convergence analysis

    Institute of Scientific and Technical Information of China (English)

    张讲社; 徐宗本; 梁怡

    1997-01-01

    A new selection mechanism termed global annealing selection (GAnS) is proposed for the genetic algorithm. It is proved that the GAnS genetic algorithm converges to the global optimums if and only if the parents are allowed to compete for reproduction, and that the variance of population’s fitness can be used as a natural stopping criterion. Numerical simulations show that the new algorithm has stronger ability to escape from local maximum and converges more rapidly than canonical genetic algorithm.

  15. Quantum Annealing and Computation: A Brief Documentary Note

    CERN Document Server

    Ghosh, Asim

    2013-01-01

    Major breakthrough in quantum computation has recently been achieved using quantum annealing to develop analog quantum computers instead of gate based computers. After a short introduction to quantum computation, we retrace very briefly the history of these developments and discuss the Indian researches in this connection and provide some interesting documents (in the Figs.) obtained from a chosen set of high impact papers (and also some recent news etc. blogs appearing in the Internet). This note is also designed to supplement an earlier note by Bose (Science and Culture, 79, pp. 337-378, 2013).

  16. P-type conductivity in annealed strontium titanate

    Energy Technology Data Exchange (ETDEWEB)

    Poole, Violet M.; Corolewski, Caleb D.; McCluskey, Matthew D., E-mail: mattmcc@wsu.edu [Department of Physics and Astronomy, Washington State University, Pullman, WA 99164-2814 (United States)

    2015-12-15

    Hall-effect measurements indicate p-type conductivity in bulk, single-crystal strontium titanate (SrTiO{sub 3}, or STO) samples that were annealed at 1200°C. Room-temperature mobilities above 100 cm{sup 2}/V s were measured, an order of magnitude higher than those for electrons (5-10 cm{sup 2}/V s). Average hole densities were in the 10{sup 9}-10{sup 10} cm{sup −3} range, consistent with a deep acceptor.

  17. Optimal estuarine sediment monitoring network design with simulated annealing.

    Science.gov (United States)

    Nunes, L M; Caeiro, S; Cunha, M C; Ribeiro, L

    2006-02-01

    An objective function based on geostatistical variance reduction, constrained to the reproduction of the probability distribution functions of selected physical and chemical sediment variables, is applied to the selection of the best set of compliance monitoring stations in the Sado river estuary in Portugal. These stations were to be selected from a large set of sampling stations from a prior field campaign. Simulated annealing was chosen to solve the optimisation function model. Both the combinatorial problem structure and the resulting candidate sediment monitoring networks are discussed, and the optimal dimension and spatial distribution are proposed. An optimal network of sixty stations was obtained from an original 153-station sampling campaign.

  18. Radiation and annealing effects on integrated bipolar Operational Amplifier

    Science.gov (United States)

    Assaf, J.

    2017-02-01

    Integrated bipolar Operational Amplifier (op-amp) type μA 741 was irradiated with neutrons and gamma rays. The radiation on gain factors, slew rate, and power supply current have been evaluated. The experimental results show a decrease of these parameter values after exposing to the radiation. The advantage of the increase of the voltage power supplies and the thermal annealing treatment on the damaged parameters was also explored. The relationship among different frequency response parameters is also studied leading to an analytical formula for the above degraded parameters.

  19. Crosshole Tomography, Waveform Inversion, and Anisotropy: A Combined Approach Using Simulated Annealing

    Science.gov (United States)

    Afanasiev, M.; Pratt, R. G.; Kamei, R.; McDowell, G.

    2012-12-01

    Crosshole seismic tomography has been used by Vale to provide geophysical images of mineralized massive sulfides in the Eastern Deeps deposit at Voisey's Bay, Labrador, Canada. To date, these data have been processed using traveltime tomography, and we seek to improve the resolution of these images by applying acoustic Waveform Tomography. Due to the computational cost of acoustic waveform modelling, local descent algorithms are employed in Waveform Tomography; due to non-linearity an initial model is required which predicts first-arrival traveltimes to within a half-cycle of the lowest frequency used. Because seismic velocity anisotropy can be significant in hardrock settings, the initial model must quantify the anisotropy in order to meet the half-cycle criterion. In our case study, significant velocity contrasts between the target massive sulfides and the surrounding country rock led to difficulties in generating an accurate anisotropy model through traveltime tomography, and our starting model for Waveform Tomography failed the half-cycle criterion at large offsets. We formulate a new, semi-global approach for finding the best-fit 1-D elliptical anisotropy model using simulated annealing. Through random perturbations to Thompson's ɛ parameter, we explore the L2 norm of the frequency-domain phase residuals in the space of potential anisotropy models: If a perturbation decreases the residuals, it is always accepted, but if a perturbation increases the residuals, it is accepted with the probability P = exp(-(Ei-E)/T). This is the Metropolis criterion, where Ei is the value of the residuals at the current iteration, E is the value of the residuals for the previously accepted model, and T is a probability control parameter, which is decreased over the course of the simulation via a preselected cooling schedule. Convergence to the global minimum of the residuals is guaranteed only for infinitely slow cooling, but in practice good results are obtained from a variety

  20. The metal-insulator transition in vanadium dioxide: A view at bulk and surface contributions for thin films and the effect of annealing

    Science.gov (United States)

    Yin, W.; West, K. G.; Lu, J. W.; Pei, Y.; Wolf, S. A.; Reinke, P.; Sun, Y.

    2009-06-01

    Vanadium dioxide is investigated as potential oxide barrier in spin switches, and in order to incorporate VO2 layers in complex multilayer devices, it is necessary to understand the relation between bulk and surface/interface properties. Highly oriented VO2 thin films were grown on (0001) sapphire single crystal substrates with reactive bias target ion beam deposition. In the analysis of the VO2 films, bulk-sensitive methods [x-ray diffraction (XRD) and transport measurements] and surface sensitive techniques [photoelectron spectroscopy (PES) and scanning tunneling microscopy and spectroscopy] were employed. The samples were subjected to heating cycles with annealing temperatures of up to 425 and 525K. Prior to annealing the VO2 films exhibit the transition from the monoclinic to the tetragonal phase with the concurrent change in conductivity by more than a factor of 103 and their phase purity is confirmed by XRD. Annealing to 425K and thus cycling across the metal-insulator transition (MIT) temperature has no impact on the bulk properties of the VO2 film but the surface undergoes irreversible electronic changes. The observation of the valence band with PES during the annealing illustrates that the surface adopts a partially metallic character, which is retained after cooling. Annealing to a higher temperature (525K ) triggers a modification of the bulk, which is evidenced by a considerable reduction in the MIT characteristics, and a degradation in crystallite morphology. The local measurement of the conductivity with scanning tunneling spectroscopy shows the transition of the surface from predominantly semiconducting surface prior to annealing to a surface with an overwhelming contribution from metallic sections afterward. The spatial distribution of metallic regions cannot be linked in a unique manner to the crystallite size or location within the crystallites. The onset of oxygen depletion at the surface is held responsible for this behavior. The onset of bulk