In Situ Identification and Stratification of Monochloramine Inhibition Effects on Nitrifying Biofilms as Determined by the Use of Microelectrodes

Science.gov (United States)

The nitrifying biofilm grown in an annular biofilm reactor and the microbial deactivation achieved after monochloramine treatment were investigated using microelectrodes. The nitrifying biofilm ammonium microprofile was measured and the effect of monochloramine on nitrifying bio...

Comparison of electrochemical method with ozonation, chlorination and monochloramination in drinking water disinfection

Energy Technology Data Exchange (ETDEWEB)

Li Hongna, E-mail: lihongna@gmail.com [Department of Environmental Engineering, Peking University, Key Laboratory of Water and Sediment Sciences, Ministry of Education, Beijing 100871 (China); Zhu Xiuping [Department of Environmental Engineering, Peking University, Key Laboratory of Water and Sediment Sciences, Ministry of Education, Beijing 100871 (China); Ni Jinren, E-mail: nijinren@iee.pku.edu.cn [Department of Environmental Engineering, Peking University, Key Laboratory of Water and Sediment Sciences, Ministry of Education, Beijing 100871 (China)

2011-11-30

Highlights: > Electrochemical, O{sub 3}, NaClO and NH{sub 2}Cl were compared at respective optimal condition. > Disinfection efficacy was similar for different bacteria in electrolysis. > Harsh Bacillus was inactivated more difficult in O{sub 3}, NaClO and NH{sub 2}Cl system. > Efficient disinfection of electrolysis was attributed to nonselectivity of {center_dot}OH. > Cell surface damage was more obvious in electrochemical process than the others. - Abstract: Electrochemical process in chloride-free electrolytes was proved to be powerful in disinfection due to the strong oxidants produced in the electrolysis and no formation of disinfection byproducts (DBPs). In this study, disinfection experiments were conducted by electrochemical treatment compared with ordinary and advanced methods (ozonation, chlorination and monochloramination), with Escherichia coli (E. coli) K-12, Staphylococcus aureus (S. aureus) A106, Bacillus subtilis (BST) and an isolated Bacillus as the representative microorganisms. Firstly, factor tests were performed on E. coli to obtain the optimal conditions of the four disinfection procedures. At their respective optimal condition, CT (concentration of disinfectant x contact time) value of a 4-log E. coli inactivation was 33.5, 1440, 1575, 1674 mg min L{sup -1} for electrochemical process, ozonation, chlorination and monochloramination, respectively. It was demonstrated that the disinfection availability was in the following order: electrochemical process > ozonation > chlorination > monochloramination, which could be attributed to the hydroxyl radical generated in the electrolysis, with strong oxidizing ability and non-selectivity compared with the other three disinfectants. Moreover, the disinfection efficacy of the four disinfection procedures was compared for four different bacteria. It was found that the disinfection efficacy was similar for the selected four bacteria in electrochemical process, while in the other three treatments

Comparison of electrochemical method with ozonation, chlorination and monochloramination in drinking water disinfection

International Nuclear Information System (INIS)

Li Hongna; Zhu Xiuping; Ni Jinren

2011-01-01

Highlights: → Electrochemical, O 3 , NaClO and NH 2 Cl were compared at respective optimal condition. → Disinfection efficacy was similar for different bacteria in electrolysis. → Harsh Bacillus was inactivated more difficult in O 3 , NaClO and NH 2 Cl system. → Efficient disinfection of electrolysis was attributed to nonselectivity of ·OH. → Cell surface damage was more obvious in electrochemical process than the others. - Abstract: Electrochemical process in chloride-free electrolytes was proved to be powerful in disinfection due to the strong oxidants produced in the electrolysis and no formation of disinfection byproducts (DBPs). In this study, disinfection experiments were conducted by electrochemical treatment compared with ordinary and advanced methods (ozonation, chlorination and monochloramination), with Escherichia coli (E. coli) K-12, Staphylococcus aureus (S. aureus) A106, Bacillus subtilis (BST) and an isolated Bacillus as the representative microorganisms. Firstly, factor tests were performed on E. coli to obtain the optimal conditions of the four disinfection procedures. At their respective optimal condition, CT (concentration of disinfectant x contact time) value of a 4-log E. coli inactivation was 33.5, 1440, 1575, 1674 mg min L -1 for electrochemical process, ozonation, chlorination and monochloramination, respectively. It was demonstrated that the disinfection availability was in the following order: electrochemical process > ozonation > chlorination > monochloramination, which could be attributed to the hydroxyl radical generated in the electrolysis, with strong oxidizing ability and non-selectivity compared with the other three disinfectants. Moreover, the disinfection efficacy of the four disinfection procedures was compared for four different bacteria. It was found that the disinfection efficacy was similar for the selected four bacteria in electrochemical process, while in the other three treatments inactivation of the two

Transformation among Aromatic Iodinated Disinfection Byproducts in the Presence of Monochloramine: From Monoiodophenol to Triiodophenol and Diiodonitrophenol.

Science.gov (United States)

Gong, Tingting; Tao, Yuxian; Zhang, Xiangru; Hu, Shaoyang; Yin, Jinbao; Xian, Qiming; Ma, Jian; Xu, Bin

2017-09-19

Aromatic iodinated disinfection byproducts (DBPs) are a newly identified category of highly toxic DBPs. Among the identified aromatic iodinated DBPs, 2,4,6-triiodophenol and 2,6-diiodo-4-nitrophenol have shown relatively widespread occurrence and high toxicity. In this study, we found that 4-iodophenol underwent transformation to form 2,4,6-triiodophenol and 2,6-diiodo-4-nitrophenol in the presence of monochloramine. The transformation pathways were investigated, the decomposition kinetics of 4-iodophenol and the formation of 2,4,6-triiodophenol and 2,6-diiodo-4-nitrophenol were studied, the factors affecting the transformation were examined, the toxicity change during the transformation was evaluated, and the occurrence of the proposed transformation pathways during chloramination of source water was verified. The results revealed that 2,4,6-triiodophenol and 2,6-diiodo-4-nitrophenol, which could account for 71.0% of iodine in the transformed 4-iodophenol, were important iodinated transformation products of 4-iodophenol in the presence of monochloramine. The transformation pathways of 4-iodophenol in the presence of monochloramine were proposed and verified. The decomposition of 4-iodophenol in the presence of monochloramine followed a pseudo-second-order decay. Various factors including monochloramine dose, pH, temperature, nitrite concentration, and free chlorine contact time (before chloramination) affected the transformation. The cytotoxicity of the chloraminated 4-iodophenol samples increased continuously with contact time. The proposed transformation pathways occurred during chloramination of source water.

Hydroxylamine addition impact to Nitrosomonas europaea activity in the presence of monochloramine

Science.gov (United States)

In drinking water, monochloramine may promote ammonia–oxidizing bacteria (AOB) growth because of concurrent ammonia presence. AOB use (i) ammonia monooxygenase for biological ammonia oxidation to hydroxylamine and (ii) hydroxylamine oxidoreductase for hydroxylamine oxidation to ...

Comparative Inactivation of Murine Norovirus and MS2 Bacteriophage by Peracetic Acid and Monochloramine in Municipal Secondary Wastewater Effluent.

Science.gov (United States)

Dunkin, Nathan; Weng, ShihChi; Schwab, Kellogg J; McQuarrie, James; Bell, Kati; Jacangelo, Joseph G

2017-03-07

Chlorination has long been used for disinfection of municipal wastewater (MWW) effluent while the use peracetic acid (PAA) has been proposed more recently in the United States. Previous work has demonstrated the bactericidal effectiveness of PAA and monochloramine in wastewater, but limited information is available for viruses, especially ones of mammalian origin (e.g., norovirus). Therefore, a comparative assessment was performed of the virucidal efficacy of PAA and monochloramine against murine norovirus (MNV) and MS2 bacteriophage in secondary effluent MWW and phosphate buffer (PB). A suite of inactivation kinetic models was fit to the viral inactivation data. Predicted concentration-time (CT) values for 1-log 10 MS2 reduction by PAA and monochloramine in MWW were 1254 and 1228 mg-min/L, respectively. The 1-, 2-, and 3-log 10 model predicted CT values for MNV viral reduction in MWW were 32, 47, and 69 mg-min/L for PAA and 6, 13, and 28 mg-min/L for monochloramine, respectively. Wastewater treatment plant disinfection practices informed by MS2 inactivation data will likely be protective for public health but may overestimate CT values for reduction of MNV. Additionally, equivalent CT values in PB resulted in greater viral reduction which indicate that viral inactivation data in laboratory grade water may not be generalizable to MWW applications.

Monochloramine determination using NN diethyl-p-phenylene-diamine. Influence of iodide traces

International Nuclear Information System (INIS)

Fiquet, J.M.

1980-09-01

When determining ''D.P.D.'' free oxidizers, the monochloramine interfers in particular for iodide levels analogous to those likely to be found in sea water. This is not so for iodate. The zero time extrapolation of the change in colour curve is one method that enables the method to be made more selective [fr

Chlorination or monochloramination: Balancing the regulated trihalomethane formation and microbial inactivation in marine aquaculture waters

KAUST Repository

Sanawar, Huma; Xiong, Yanghui; Alam, Aftab; Croue, Jean-Philippe; Hong, Pei-Ying

2017-01-01

at the lowest tested concentration of chlorine (1mg/L) and contact time (1h). Comparatively, regulated THMs concentration was only detectable at 30μg/L level in one of the three sets of monochloraminated marine aquaculture waters. The average log reduction

A proposed abiotic reaction scheme for hydroxylamine and monochloramine under chloramination relevant drinking water conditions

Science.gov (United States)

Drinking water monochloramine (NH2Cl) use may promote ammonia–oxidizing bacteria (AOB) growth. For biological ammonia (NH3) oxidation, AOB use (i) ammonia monooxygenase for NH3 oxidation to hydroxylamine (NH2OH) and (ii) hydroxylamine oxidoreductase for NH2OH oxidation to nitrit...

Free chlorine and monochloramine inactivation kinetics of Aspergillus and Penicillium in drinking water.

Science.gov (United States)

Ma, Xiao; Bibby, Kyle

2017-09-01

Fungi are near-ubiquitous in potable water distribution systems, but the disinfection kinetics of commonly identified fungi are poorly studied. In the present study, laboratory scale experiments were conducted to evaluate the inactivation kinetics of Aspergillus fumigatus, Aspergillus versicolor, and Penicillium purpurogenum by free chlorine and monochloramine. The observed inactivation data were then fit to a delayed Chick-Watson model. Based on the model parameter estimation, the Ct values (integrated product of disinfectant concentration C and contact time t over defined time intervals) for 99.9% inactivation of the tested fungal strains ranged from 48.99 mg min/L to 194.7 mg min/L for free chlorine and from 90.33 mg min/L to 531.3 mg min/L for monochloramine. Fungal isolates from a drinking water system (Aspergillus versicolor and Penicillium purpurogenum) were more disinfection resistant than Aspergillus fumigatus type and clinical isolates. The required 99.9% inactivation Ct values for the tested fungal strains are higher than E. coli, a commonly monitored indicator bacteria, and within a similar range for bacteria commonly identified within water distribution systems, such as Mycobacterium spp. and Legionella spp. Copyright © 2017 Elsevier Ltd. All rights reserved.

Reduction of Human Norovirus GI, GII, and Surrogates by Peracetic Acid and Monochloramine in Municipal Secondary Wastewater Effluent.

Science.gov (United States)

Dunkin, Nathan; Weng, ShihChi; Coulter, Caroline G; Jacangelo, Joseph G; Schwab, Kellogg J

2017-10-17

The objective of this study was to characterize human norovirus (hNoV) GI and GII reductions during disinfection by peracetic acid (PAA) and monochloramine in secondary wastewater (WW) and phosphate buffer (PB) as assessed by reverse transcription-qPCR (RT-qPCR). Infectivity and RT-qPCR reductions are also presented for surrogate viruses murine norovirus (MNV) and bacteriophage MS2 under identical experimental conditions to aid in interpretation of hNoV molecular data. In WW, RT-qPCR reductions were less than 0.5 log 10 for all viruses at concentration-time (CT) values up to 450 mg-min/L except for hNoV GI, where 1 log 10 reduction was observed at CT values of less than 50 mg-min/L for monochloramine and 200 mg-min/L for PAA. In PB, hNoV GI and MNV exhibited comparable resistance to PAA and monochloramine with CT values for 2 log 10 RT-qPCR reduction between 300 and 360 mg-min/L. Less than 1 log 10 reduction was observed for MS2 and hNoV GII in PB at CT values for both disinfectants up to 450 mg-min/L. Our results indicate that hNoVs exhibit genogroup dependent resistance and that disinfection practices targeting hNoV GII will result in equivalent or greater reductions for hNoV GI. These data provide valuable comparisons between hNoV and surrogate molecular signals that can begin the process of informing regulators and engineers on WW treatment plant design and operational practices necessary to inactivate hNoVs.

Shift in the microbial ecology of a hospital hot water system following the introduction of an on-site monochloramine disinfection system.

Science.gov (United States)

Baron, Julianne L; Vikram, Amit; Duda, Scott; Stout, Janet E; Bibby, Kyle

2014-01-01

Drinking water distribution systems, including premise plumbing, contain a diverse microbiological community that may include opportunistic pathogens. On-site supplemental disinfection systems have been proposed as a control method for opportunistic pathogens in premise plumbing. The majority of on-site disinfection systems to date have been installed in hospitals due to the high concentration of opportunistic pathogen susceptible occupants. The installation of on-site supplemental disinfection systems in hospitals allows for evaluation of the impact of on-site disinfection systems on drinking water system microbial ecology prior to widespread application. This study evaluated the impact of supplemental monochloramine on the microbial ecology of a hospital's hot water system. Samples were taken three months and immediately prior to monochloramine treatment and monthly for the first six months of treatment, and all samples were subjected to high throughput Illumina 16S rRNA region sequencing. The microbial community composition of monochloramine treated samples was dramatically different than the baseline months. There was an immediate shift towards decreased relative abundance of Betaproteobacteria, and increased relative abundance of Firmicutes, Alphaproteobacteria, Gammaproteobacteria, Cyanobacteria and Actinobacteria. Following treatment, microbial populations grouped by sampling location rather than sampling time. Over the course of treatment the relative abundance of certain genera containing opportunistic pathogens and genera containing denitrifying bacteria increased. The results demonstrate the driving influence of supplemental disinfection on premise plumbing microbial ecology and suggest the value of further investigation into the overall effects of premise plumbing disinfection strategies on microbial ecology and not solely specific target microorganisms.

Shift in the microbial ecology of a hospital hot water system following the introduction of an on-site monochloramine disinfection system.

Directory of Open Access Journals (Sweden)

Julianne L Baron

Full Text Available Drinking water distribution systems, including premise plumbing, contain a diverse microbiological community that may include opportunistic pathogens. On-site supplemental disinfection systems have been proposed as a control method for opportunistic pathogens in premise plumbing. The majority of on-site disinfection systems to date have been installed in hospitals due to the high concentration of opportunistic pathogen susceptible occupants. The installation of on-site supplemental disinfection systems in hospitals allows for evaluation of the impact of on-site disinfection systems on drinking water system microbial ecology prior to widespread application. This study evaluated the impact of supplemental monochloramine on the microbial ecology of a hospital's hot water system. Samples were taken three months and immediately prior to monochloramine treatment and monthly for the first six months of treatment, and all samples were subjected to high throughput Illumina 16S rRNA region sequencing. The microbial community composition of monochloramine treated samples was dramatically different than the baseline months. There was an immediate shift towards decreased relative abundance of Betaproteobacteria, and increased relative abundance of Firmicutes, Alphaproteobacteria, Gammaproteobacteria, Cyanobacteria and Actinobacteria. Following treatment, microbial populations grouped by sampling location rather than sampling time. Over the course of treatment the relative abundance of certain genera containing opportunistic pathogens and genera containing denitrifying bacteria increased. The results demonstrate the driving influence of supplemental disinfection on premise plumbing microbial ecology and suggest the value of further investigation into the overall effects of premise plumbing disinfection strategies on microbial ecology and not solely specific target microorganisms.

N-nitrosamine formation by monochloramine, free chlorine, and peracetic acid disinfection with presence of amine precursors in drinking water system.

Science.gov (United States)

West, Danielle M; Wu, Qihua; Donovan, Ariel; Shi, Honglan; Ma, Yinfa; Jiang, Hua; Wang, Jianmin

2016-06-01

In this study, the formation of eight N-nitrosamines, N-nitrosodimethylamine (NDMA), N-nitrosodiethylamine, N-nitrosomethylamine, N-nitrosodi-n-propylamine, N-nitrosodi-n-butylamine, N-Nitrosopiperidine, N-Nitrosopyrrolidine, N-Nitrosomorpholine, were systematically evaluated with respect to seven N-nitrosamine precursors (dimethylamine, trimethylamine, 3-(dimethylaminomethyl)indole, 4-dimethylaminoantipyrine, ethylmethylamine, diethylamine, dipropylamine) and three disinfectants (monochloramine, free chlorine, peracetic acid) under variable dosages, exposure times, and pH in a drinking water system. Without the presence of the seven selected N-nitrosamine precursors N-nitrosamine formation was not observed under any tested condition except very low levels of N-Nitrosopyrrolidine under some conditions. With selected N-nitrosamine precursors present N-nitrosamines formed at different levels under different conditions. The highest N-nitrosamine formation was NDMA with a maximum concentration of 1180 ng/L by monochloramine disinfection with precursors present; much lower levels of N-nitrosamines were formed by free chlorine disinfection; and no detectable level of N-nitrosamines were observed by peracetic acid disinfection except low level of N-Nitrosodi-n-propylamine under some conditions. NDMA formation was not affected by pH while four other N-nitrosamine formations were slightly affected by sample pH tested between 7 and 9, with formation decreasing with increasing pH. Monochloramine exposure time study displayed fast formation of N-nitrosamines, largely formed in four hours of exposure and maximized after seven days. This was a systematic study on the N-nitrosamine formation with the seven major N-nitrosamine precursors presence and absence under different conditions, including peracetic acid disinfection which has not been studied elsewhere. Copyright © 2016 Elsevier Ltd. All rights reserved.

Spectroscopy of reactive species produced by low-energy atmospheric-pressure plasma on conductive target material surface

International Nuclear Information System (INIS)

Yamada, Hiromasa; Sakakita, Hajime; Kato, Susumu; Kim, Jaeho; Kiyama, Satoru; Fujiwara, Masanori; Itagaki, Hirotomo; Ikehara, Yuzuru; Okazaki, Toshiya; Ikehara, Sanae; Nakanishi, Hayao; Shimizu, Nobuyuki

2016-01-01

A method for blood coagulation using low-energy atmospheric-pressure plasma (LEAPP) is confirmed as an alternative procedure to reduce tissue damage caused by heat. Blood coagulation using LEAPP behaves differently depending on working gas species; helium is more effective than argon in promoting fast coagulation. To analyse the difference in reactive species produced by helium and argon plasma, spectroscopic measurements were conducted without and with a target material. To compare emissions, blood coagulation experiments using LEAPP for both plasmas were performed under almost identical conditions. Although many kinds of reactive species such as hydroxyl radicals and excited nitrogen molecules were observed with similar intensity in both plasmas, intensities of nitrogen ion molecules and nitric oxide molecules were extremely strong in the helium plasma. It is considered that nitrogen ion molecules were mainly produced by penning ionization by helium metastable. Near the target, a significant increase in the emissions of reactive species is observed. There is a possibility that electron acceleration was induced in a local electric field formed on the surface. However, in argon plasma, emissions from nitrogen ion were not measured even near the target surface. These differences between the two plasmas may be producing the difference in blood coagulation behaviour. To control the surrounding gas of the plasma, a gas-component-controllable chamber was assembled. Filling the chamber with O 2 /He or N 2 /He gas mixtures selectively produces either reactive oxygen species or reactive nitrogen species. Through selective treatments, this chamber would be useful in studying the effects of specific reactive species on blood coagulation. (paper)

Spectroscopy of reactive species produced by low-energy atmospheric-pressure plasma on conductive target material surface

Science.gov (United States)

Yamada, Hiromasa; Sakakita, Hajime; Kato, Susumu; Kim, Jaeho; Kiyama, Satoru; Fujiwara, Masanori; Itagaki, Hirotomo; Okazaki, Toshiya; Ikehara, Sanae; Nakanishi, Hayao; Shimizu, Nobuyuki; Ikehara, Yuzuru

2016-10-01

A method for blood coagulation using low-energy atmospheric-pressure plasma (LEAPP) is confirmed as an alternative procedure to reduce tissue damage caused by heat. Blood coagulation using LEAPP behaves differently depending on working gas species; helium is more effective than argon in promoting fast coagulation. To analyse the difference in reactive species produced by helium and argon plasma, spectroscopic measurements were conducted without and with a target material. To compare emissions, blood coagulation experiments using LEAPP for both plasmas were performed under almost identical conditions. Although many kinds of reactive species such as hydroxyl radicals and excited nitrogen molecules were observed with similar intensity in both plasmas, intensities of nitrogen ion molecules and nitric oxide molecules were extremely strong in the helium plasma. It is considered that nitrogen ion molecules were mainly produced by penning ionization by helium metastable. Near the target, a significant increase in the emissions of reactive species is observed. There is a possibility that electron acceleration was induced in a local electric field formed on the surface. However, in argon plasma, emissions from nitrogen ion were not measured even near the target surface. These differences between the two plasmas may be producing the difference in blood coagulation behaviour. To control the surrounding gas of the plasma, a gas-component-controllable chamber was assembled. Filling the chamber with O2/He or N2/He gas mixtures selectively produces either reactive oxygen species or reactive nitrogen species. Through selective treatments, this chamber would be useful in studying the effects of specific reactive species on blood coagulation.

Factors affecting THMs, HAAs and HNMs formation of Jin Lan Reservoir water exposed to chlorine and monochloramine.

Science.gov (United States)

Hong, Huachang; Xiong, Yujing; Ruan, Mengyong; Liao, Fanglei; Lin, Hongjun; Liang, Yan

2013-02-01

The formations of THMs, HAAs, and HNMs from chlorination and chloramination of water from Jinlan Reservoir were investigated in this study. Results showed that monochloramine rather than chlorine generally resulted in lower concentration of DBPs, and the DBPs formation varied greatly as the treatment conditions changed. Specifically, the yields of THMs, HAAs and HNMs all increased with the high bromide level and high disinfectant dose both during chlorination and chloramination. The longer reaction time had a positive effect on the formation of THMs, HAAs and HNMs during chlorination and HNMs during chloramination. However, no time effect was observed on the formation of THMs and HAAs during chloramination. An increase in pH enhanced the levels of THMs and HNMs upon chlorination but reduced levels of HNMs upon chloramination. As for the THMs in chloramination and HAAs in chlorination and chloramination, no obvious pH effect was observed. The elevated temperature significantly increased the yields of THMs during chlorination and HNMs during chloramination, but has no effect on THMs and HAAs yields during chloramination. In the same temperature range, the formation of HAAs and HNMs in chlorination showed a first increasing and then a decreasing trend. In chloramination study, addition of nitrite markedly increased the formation of HNMs but had little impact on the formation of THMs and HAAs. While in chlorination study, the presence of high nitrite levels significantly reduced the yields of THMs, HAAs and HNMs. Range analysis revealed that the bromide and disinfectant levels were the major factors affecting THMs, HAAs and HNMs formation, in both chlorination and chloramination. Finally, comparisons of the speciation of mono-halogenated, di-halogenated, tri-halogenated HAAs and HNMs between chlorination and monochloramination were also conducted, and factors influencing the speciation pattern were identified. Copyright © 2012 Elsevier B.V. All rights reserved.

Decolorization and Mineralization of Reactive Dyes, by the H2O2/UV Process With Electrochemically Produced H2O2

NARCIS (Netherlands)

Jeric, T.; Bisselink, R.J.M.; Tongeren, W. van; Marechal. A.M. Le

2013-01-01

Decolorization of Reactive Red 238, Reactive Orange 16, Reactive Black 5 and Reactive Blue 4 was studied in the UV/H2O2 process with H2O2 being produced electrochemically. The experimental results show that decolorization increased considerably when switching on the electrochemical production of

Study of CO2 gasification reactivity of biocarbon produced at different conditions

OpenAIRE

Wang, Liang; Maziarka, Przemysław; Skreiberg, Øyvind; Løvås, Terese; Wadrzyk, Mariusz; Sevault, Alexis

2017-01-01

Biocarbon has a great potential to replace fossil reductants and help reduce greenhouse gas emissions from carbon intensive metallurgical industries. In this work, biocarbon samples were produced from Norway spruce under different final temperatures (550, 650 and 800 °C) and holding times (10 and 30 minutes). The CO2 gasification reactivity of the biocarbon, or biomass char, samples was investigated in a thermogravimetric analyser at different gasification temperatures (850, 900 and 950 °C). ...

Free radical reactions of monochloramine and hydroxylamine in aqueous solution

International Nuclear Information System (INIS)

Johnson, H.D.; Cooper, William J.; Mezyk, Stephen P.; Bartels, David M.

2002-01-01

The use of Advanced Oxidation Technologies to destroy organic contaminants in drinking water may be impacted by the presence of disinfection chemicals such as monochloramine (NH 2 Cl). To allow a quantitative evaluation of the effect of NH 2 Cl on the destruction of organics in water rate constants for its reaction with the hydrated electron, the hydroxyl radical and the hydrogen atom were determined in this study. The corresponding values of (2.2±0.2)x10 10 , (2.8±0.2)x10 9 , and (1.2±0.1)x10 9 M -1 s -1 , respectively, were incorporated into a kinetic computer model whose predictions were in good agreement with experimental chloramine removal under large scale, steady-state electron-beam irradiation conditions. Rate constants were also determined for the reaction of the hydroxyl radical and hydrogen atom with the chloramine hydration product hydroxylamine to supplement established literature data. Hydroxyl radical rate constants for the basic (NH 2 OH) and acidic (NH 3 OH + ) forms were determined as (8.5±0.4)x10 9 and ≤5x10 7 M -1 s -1 , respectively, while for hydrogen atom reaction, corresponding rate constants of (4.5±0.1)x10 7 and (3.6±1.5)x10 5 M -1 s -1 were found

Electrophilic acid gas-reactive fluid, proppant, and process for enhanced fracturing and recovery of energy producing materials

Science.gov (United States)

Fernandez, Carlos A.; Heldebrant, David J.; Bonneville, Alain; Jung, Hun Bok; Carroll, Kenneth C.

2018-01-23

An electrophilic acid gas-reactive fracturing fluid, proppant, and process are detailed. The fluid expands in volume to provide rapid and controlled increases in pressure that enhances fracturing in subterranean bedrock for recovery of energy-producing materials. The proppant stabilizes fracture openings in the bedrock to enhance recovery of energy-producing materials.

Reactivity Of Radiolytically-Produced Nitrogen Oxide Radicals Toward Aromatic Compounds

International Nuclear Information System (INIS)

Elias, Gracy

2010-01-01

radiolysis of the modifier (Cs-7SB), which solvates both metal complexes, is responsible for this change. These reactions presumably occur due to reactions with radiolytically-produced nitrogen-centered radicals like (sm b ullet)NO, (sm b ullet)NO 2 and (sm b ullet)NO 3 . Anisole (C 6 H 5 -OCH 3 ) was used in this study as a surrogate for Cs-7SB, since both are aryl ethers. Toluene was used as a surrogate for Cs-7SB because of the alkyl group on the benzene ring in both molecules. Anisole, highly reactive in acids, is a small molecule compared to Cs-7SB and the nitration products are easier to identify compared to those for the larger Cs-7SB molecule. Toluene is less reactive than anisole. Therefore, the highly reactive anisole and the less reactive toluene were considered in this study as model compounds to compare the reaction mechanisms and the nitrated products in acidic media under irradiation. Experiments were designed to elucidate the mechanism of the nitration of aromatic rings in γ-irradiated aqueous nitric acid. Since a suite of radical and ionic reactive species are produced in this condensed-phase system, solutions of nitric acid, neutral nitrate and neutral nitrite were irradiated in separate experiments to isolate selected reactive species. Product nitration species were assessed by high performance liquid chromatography (HPLC) with a reversed phase C-18 column and photodiode array detector. The nitrated anisole product distributions were the same with and without radiation in acidic solution, although more products were formed with radiation. In the irradiated acidic condensed phase, radiation-enhanced nitrous acid-catalyzed nitrosonium ion electrophilic aromatic substitution followed by oxidation reactions dominated over radical addition reactions. In contrast, the distribution of nitrated derivatives for toluene showed nitronium ion electrophilic substitution in the unirradiated acidic medium as a result of thermal nitration only at elevated temperatures

Rudimentary, low tech incinerators as a means to produce reactive pozzolan out of sugar cane straw

International Nuclear Information System (INIS)

Martirena, Fernando; Middendorf, Bernhard; Day, Robert L.; Gehrke, Matthias; Roque, Pablo; Martinez, Lesday; Betancourt, Sergio

2006-01-01

The ashes of agricultural wastes from the processing of sugar cane are recognized as having pozzolanic properties. Burning of these wastes under controlled conditions, e.g. temperature and residence time results in significant improvement in reactivity. There are many reports of low-tech incinerators that have been successfully used to produce reactive rice husk ash in Asia. The paper presents the results of the evaluation of a rudimentary incinerator where sugar cane straw is burnt in order to obtain a reactive ash. The incinerator is designed and constructed according to state-of-the-art recommendations for this kind of device. Various burning trials were performed in order to obtain ash for the experiment. X-ray diffraction analysis performed on powdered ash shows significant presence of amorphous (glassy) material. Lime-pozzolana pastes were prepared. The pastes were subjected to X-ray diffraction, thermo-gravimetric analysis, chemical titration, and SEM observation, as a means to examine the pozzolanicity of the ash via the progress with time of calcium hydroxide consumption, and changes in the pore size distribution and strength. Calcium silicate hydrate phases are the main reaction product of the pozzolanic reaction. The long residence time of the ash in the burning chamber seems to be the reason for the fairly low reactivity of the ash; the reactivity of the ash was not significantly improved in comparison with that of the ash burnt in uncontrolled conditions in the open air

Kinetics of membrane damage to high (HNA) and low (LNA) nucleic acid bacterial clusters in drinking water by ozone, chlorine, chlorine dioxide, monochloramine, ferrate(VI), and permanganate.

Science.gov (United States)

Ramseier, Maaike K; von Gunten, Urs; Freihofer, Pietro; Hammes, Frederik

2011-01-01

Drinking water was treated with ozone, chlorine, chlorine dioxide, monochloramine, ferrate(VI), and permanganate to investigate the kinetics of membrane damage of native drinking water bacterial cells. Membrane damage was measured by flow cytometry using a combination of SYBR Green I and propidium iodide (SGI+PI) staining as indicator for cells with permeabilized membranes and SGI alone to measure total cell concentration. SGI+PI staining revealed that the cells were permeabilized upon relatively low oxidant exposures of all tested oxidants without a detectable lag phase. However, only ozonation resulted in a decrease of the total cell concentrations for the investigated reaction times. Rate constants for the membrane damage reaction varied over seven orders of magnitude in the following order: ozone > chlorine > chlorine dioxide ≈ ferrate > permanganate > chloramine. The rate constants were compared to literature data and were in general smaller than previously measured rate constants. This confirmed that membrane integrity is a conservative and therefore safe parameter for disinfection control. Interestingly, the cell membranes of high nucleic acid (HNA) content bacteria were damaged much faster than those of low nucleic acid (LNA) content bacteria during treatment with chlorine dioxide and permanganate. However, only small differences were observed during treatment with chlorine and chloramine, and no difference was observed for ferrate treatment. Based on the different reactivity of these oxidants it was suggested that HNA and LNA bacterial cell membranes have a different chemical constitution. Copyright © 2010 Elsevier Ltd. All rights reserved.

Reactive melt infiltration of copper in Al–Cr preforms produced through combustion synthesis

International Nuclear Information System (INIS)

Naplocha, Krzysztof; Granat, Kazimierz; Kaczmar, Jacek

2014-01-01

Highlights: • Determination of microstructure and phase transformation during combustion synthesis and reactive infiltration. • Squeeze casting of Cu inducing reactive infiltration of Al–Cr intermetallic porous preform. • Fabrication of unique composite material resisted to high temperature oxidation. - Abstract: Combustion synthesis of Al–Cr preforms used for infiltration and reinforcing of composite materials was developed. Compacts of powdered Al and Cr with stoichiometric ratio Al/Cr equal to 2/1 were synthesized in a microwave reactor furnished with a pyrometer for controlling phase transformations. Due to low enthalpy of the reaction, green compacts were preheated and ignition occurred together with partial melting of Al at the interface with Cr particles. The synthesis proceeded by peritectic transformations L + Al 7 Cr → L + Al 11 Cr 2 → L + Al 4 Cr, reaching maximum temperature of ca. 1000 °C. Porous structures including residual unprocessed Cr particles were soaked to homogenize them and to transform the phases into the stable intermetallic compound Al 9 Cr 4 . Reactive infiltration of the preforms with molten Cu proceeds along with interfacial diffusion of Al that, released from a preform, infiltrates into the matrix changing its composition to Cu 9 Al 4 (Cr). At the same time, the preform is decomposed and converted into a mixture of globular precipitates of Cr 52 Al 35 Cu 13 embedded in the Cu 47 Al 41 Cr 12 phase. The produced composite materials exhibit significant hardness and oxidation resistance at elevated temperatures. The protective layer is composed of oxides Al 2 O 3 and (AlCu) 2 O 3 created at parabolic constant oxidation rate (k p ) equal to 1.9 × 10 −6 g 2 m −4 s −1

Effect of immersion chilling of broiler chicken carcasses in monochloramine on lipid oxidation and halogenated residual compound formation.

Science.gov (United States)

Axtell, Stephen P; Russell, Scott M; Berman, Elliot

2006-04-01

This study was conducted to evaluate the effect of immersion chilling of broiler chicken carcasses in tap water (TAP) or TAP containing 50 ppm of monochloramine (MON) with respect to chloroform formation, total chlorine content, 2-thiobarbituric acid (TBA) values, and fatty acid profiles. Ten broiler chicken carcasses were chilled in TAP or MON for 6 h. After exposure, the carcasses were removed and cut in half along the median plane into right and left halves. After roasting the left halves, samples of the breast, thigh, and skin (with fat) were collected, subjected to fatty acid profiling, and assayed for chloroform, total chlorine, and TBA. The uncooked right halves of each carcass were stored at 4 degrees C for 10 days and then roasted. After roasting these right halves, samples of breast, thigh, and skin (with fat) were collected from each carcass half, subjected to fatty acid profiling, and assayed for chloroform, total chlorine, and TBA. There were no statistical differences between TAP- and MON-treated fresh or stored products with regard to chloroform levels, total chlorine content, TBA values, or fatty acid profiles.

Pyrimidine nucleobase radical reactivity in DNA and RNA

Science.gov (United States)

Greenberg, Marc M.

2016-11-01

Nucleobase radicals are major products of the reactions between nucleic acids and hydroxyl radical, which is produced via the indirect effect of ionizing radiation. The nucleobase radicals also result from hydration of cation radicals that are produced via the direct effect of ionizing radiation. The role that nucleobase radicals play in strand scission has been investigated indirectly using ionizing radiation to generate them. More recently, the reactivity of nucleobase radicals resulting from formal hydrogen atom or hydroxyl radical addition to pyrimidines has been studied by independently generating the reactive intermediates via UV-photolysis of synthetic precursors. This approach has provided control over where the reactive intermediates are produced within biopolymers and facilitated studying their reactivity. The contributions to our understanding of pyrimidine nucleobase radical reactivity by this approach are summarized.

Pay-as-bid based reactive power market

International Nuclear Information System (INIS)

Amjady, N.; Rabiee, A.; Shayanfar, H.A.

2010-01-01

In energy market clearing, the offers are stacked in increasing order and the offer that intersects demand curve, determines the market clearing price (MCP). In reactive power market, the location of reactive power compensator is so important. A low cost reactive producer may not essentially be favorable if it is far from the consumer. Likewise, a high cost local reactive compensator at a heavily loaded demand center of network could be inevitably an alternative required to produce reactive power to maintain the integrity of power system. Given the background, this paper presents a day-ahead reactive power market based on pay-as-bid (PAB) mechanism. Generators expected payment function (EPF) is used to construct a bidding framework. Then, total payment function (TPF) of generators is used as the objective function of optimal power flow (OPF) problem to clear the PAB based market. The CIGRE-32 bus test system is used to examine the effectiveness of the proposed reactive power market.

Pay-as-bid based reactive power market

Energy Technology Data Exchange (ETDEWEB)

Amjady, N. [Department of Electrical Engineering, Semnan University, Semnan (Iran, Islamic Republic of); Rabiee, A., E-mail: Rabiee@iust.ac.i [Center of Excellence for Power System Automation and Operation, Department of Electrical Engineering, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Shayanfar, H.A. [Center of Excellence for Power System Automation and Operation, Department of Electrical Engineering, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of)

2010-02-15

In energy market clearing, the offers are stacked in increasing order and the offer that intersects demand curve, determines the market clearing price (MCP). In reactive power market, the location of reactive power compensator is so important. A low cost reactive producer may not essentially be favorable if it is far from the consumer. Likewise, a high cost local reactive compensator at a heavily loaded demand center of network could be inevitably an alternative required to produce reactive power to maintain the integrity of power system. Given the background, this paper presents a day-ahead reactive power market based on pay-as-bid (PAB) mechanism. Generators expected payment function (EPF) is used to construct a bidding framework. Then, total payment function (TPF) of generators is used as the objective function of optimal power flow (OPF) problem to clear the PAB based market. The CIGRE-32 bus test system is used to examine the effectiveness of the proposed reactive power market.

Reactive Power from Distributed Energy

Energy Technology Data Exchange (ETDEWEB)

Kueck, John; Kirby, Brendan; Rizy, Tom; Li, Fangxing; Fall, Ndeye

2006-12-15

Distributed energy is an attractive option for solving reactive power and distribution system voltage problems because of its proximity to load. But the cost of retrofitting DE devices to absorb or produce reactive power needs to be reduced. There also needs to be a market mechanism in place for ISOs, RTOs, and transmission operators to procure reactive power from the customer side of the meter where DE usually resides. (author)

Reactive Power from Distributed Energy

International Nuclear Information System (INIS)

Kueck, John; Kirby, Brendan; Rizy, Tom; Li, Fangxing; Fall, Ndeye

2006-01-01

Distributed energy is an attractive option for solving reactive power and distribution system voltage problems because of its proximity to load. But the cost of retrofitting DE devices to absorb or produce reactive power needs to be reduced. There also needs to be a market mechanism in place for ISOs, RTOs, and transmission operators to procure reactive power from the customer side of the meter where DE usually resides. (author)

Reactive Programming in Standard ML

OpenAIRE

Pucella, Riccardo

2004-01-01

Reactive systems are systems that maintain an ongoing interaction with their environment, activated by receiving input events from the environment and producing output events in response. Modern programming languages designed to program such systems use a paradigm based on the notions of instants and activations. We describe a library for Standard ML that provides basic primitives for programming reactive systems. The library is a low-level system upon which more sophisticated reactive behavi...

Reactive sites influence in PMMA oligomers reactivity: a DFT study

Science.gov (United States)

Paz, C. V.; Vásquez, S. R.; Flores, N.; García, L.; Rico, J. L.

2018-01-01

In this work, we present a theoretical study of methyl methacrylate (MMA) living anionic polymerization. The study was addressed to understanding two important experimental observations made for Michael Szwarc in 1956. The unexpected effect of reactive sites concentration in the propagation rate, and the self-killer behavior of MMA (deactivating of living anionic polymerization). The theoretical calculations were performed by density functional theory (DFT) to obtain the frontier molecular orbitals values. These values were used to calculate and analyze the chemical interaction descriptors in DFT-Koopmans’ theorem. As a result, it was observed that the longest chain-length species (related with low concentration of reactive sites) exhibit the highest reactivity (behavior associated with the increase of the propagation rate). The improvement in this reactivity was attributed to the crosslinking produced in the polymethyl methacrylate chains. Meanwhile, the self-killer behavior was associated with the intermolecular forces present in the reactive sites. This behavior was associated to an obstruction in solvation, since the active sites remained active through all propagation species. The theoretical results were in good agreement with the Szwarc experiments.

On the Construction of Sorted Reactive Systems

DEFF Research Database (Denmark)

Birkedal, Lars; Debois, Søren; Hildebrandt, Thomas

2008-01-01

We develop a theory of sorted bigraphical reactive systems. Every application of bigraphs in the literature has required an extension, a sorting, of pure bigraphs. In turn, every such application has required a redevelopment of the theory of pure bigraphical reactive systems for the sorting at hand...... bigraphs. Technically, we give our construction for ordinary reactive systems, then lift it to bigraphical reactive systems. As such, we give also a construction of sortings for ordinary reactive systems. This construction is an improvement over previous attempts in that it produces smaller and much more...

Treating water-reactive wastes

International Nuclear Information System (INIS)

Lussiez, G.W.

1993-01-01

Some compounds and elements, such as lithium hydride, magnesium, sodium, and calcium react violently with water to generate much heat and produce hydrogen. The hydrogen can ignite or even form an explosive mixture with air. Other metals may react rapidly only if they are finely divided. Some of the waste produced at Los Alamos National Laboratory includes these metals that are contaminated with radioactivity. By far the greatest volume of water-reactive waste is lithium hydride contaminated with depleted uranium. Reactivity of the water-reactive wastes is neutralized with an atmosphere of humid nitrogen, which prevents the formation of an explosive mixture of hydrogen and air. When we adjust the temperature of the nitrogen and the humidifier, the nitrogen can be more or less humid, and the rate of reaction can be adjusted and controlled. Los Alamos has investigated the rates of reaction of lithium hydride as a function of the temperature and humidity, and, as anticipated, they in with in temperature and humidity. Los Alamos will investigate other variables. For example, the nitrogen flow will be optimized to conserve nitrogen and yet keep the reaction rates high. Reaction rates will be determined for various forms of lithium waste, from small chips to powder. Bench work will lead to the design of a skid-mounted process for treating wastes. Other water-reactive wastes will also be investigated

Practical use of chemical probes for reactive oxygen species produced in biological systems by {gamma}-irradiation

Energy Technology Data Exchange (ETDEWEB)

Lee, Min Hee; Moon, Yu Ran; Chung, Byung Yeoup; Kim, Jae-Sung [Radiation Research Division for Bio-technology, Korea Atomic Energy Research Institute, 1266 Sinjeong-dong, Jeongeup-si, Jeollabuk-do 580-185 (Korea, Republic of); Lee, Kang-Soo [Crop Production and Technology Major, Chonbuk National University, Jeonju 561-756 (Korea, Republic of); Cho, Jae-Young [Bio-environmental Science Major, Chonbuk National University, Jeonju 561-756 (Korea, Republic of); Kim, Jin-Hong [Radiation Research Division for Bio-technology, Korea Atomic Energy Research Institute, 1266 Sinjeong-dong, Jeongeup-si, Jeollabuk-do 580-185 (Korea, Republic of)], E-mail: jhongkim@kaeri.re.kr

2009-05-15

Application of chemical probes, for detection of reactive oxygen species (ROS), was tested during {gamma}-irradiation. The ethanol/{alpha}-(4-pyridyl-1-oxide)-N-tert-butylnitrone (4-POBN) and 3,3'-diaminobenzidine (DAB) were structurally stable enough to detect {sup {center_dot}}OH and H{sub 2}O{sub 2}, increasingly generated by {gamma}-irradiation up to 1000 Gy. Interestingly, the production rate of H{sub 2}O{sub 2}, but not {sup {center_dot}}OH, during {gamma}-irradiation, was significantly different between in vitro systems of lettuce and spinach. These results suggest that 4-POBN and DAB could be utilized as a semi-quantitative probe to quantify {sup {center_dot}}OH and H{sub 2}O{sub 2}, produced by {gamma}-irradiation up to 1000 Gy.

Hybrid TiO2 -Ruthenium Nano-photosensitizer Synergistically Produces Reactive Oxygen Species in both Hypoxic and Normoxic Conditions.

Science.gov (United States)

Gilson, Rebecca C; Black, Kvar C L; Lane, Daniel D; Achilefu, Samuel

2017-08-28

Photodynamic therapy (PDT) is widely used to treat diverse diseases, but its dependence on oxygen to produce cytotoxic reactive oxygen species (ROS) diminishes the therapeutic effect in a hypoxic environment, such as solid tumors. Herein, we developed a ROS-producing hybrid nanoparticle-based photosensitizer capable of maintaining high levels of ROS under both normoxic and hypoxic conditions. Conjugation of a ruthenium complex (N3) to a TiO 2 nanoparticle afforded TiO 2 -N3. Upon exposure of TiO 2 -N3 to light, the N3 injected electrons into TiO 2 to produce three- and four-fold more hydroxyl radicals and hydrogen peroxide, respectively, than TiO 2 at 160 mmHg. TiO 2 -N3 maintained three-fold higher hydroxyl radicals than TiO 2 under hypoxic conditions via N3-facilitated electron-hole reduction of adsorbed water molecules. The incorporation of N3 transformed TiO 2 from a dual type I and II PDT agent to a predominantly type I photosensitizer, irrespective of the oxygen content. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

An introduction to reactive power compensation for wind farms

Energy Technology Data Exchange (ETDEWEB)

Nigim, K.A. [Waterloo Univ., Ont. (Canada). Dept. of Electrical and Computer Engineering; Cairo Univ., Giza (Egypt). Faculty of Engineering; Zobaa, A.F.; El Amin, I. [King Fahd Univ. of Petroleum and Minerals, Dhahran (Saudi Arabia). Dept. of Electrical Engineering

2005-07-01

The paper summarises the refereed contributions of seven articles reviewed for publication in the IJETP - Special Issue on 'Reactive compensation for wind farms'. The main goal of the special issue is to provide a forum to exchange information on the reactive power compensation requirements for wind farms and introducing possible price mechanisms for today's deregulated power industry. Uncompensated reactive power causes stress on the hosting utility grid as well as added expenses, which create in difficulties for power purchasing agreements from independent wind energy producers. Wind power producers need to comply with the hosting utility grid interconnection standards, e.g., voltage and frequency, as well as to provide controllable active and reactive sources of power. Active power supply is mainly dependent on the potential of wind power produced and the turbine design. Reactive power demand on the other hand depends on the conversion devices and the recovered power quantity fed to the grid. Static Var Compensators (SVC), Unified Power Quality Conditioners (UPQC), Unified Power Flow Controllers (UPFC), and the Distributed Static Synchronous Compensators (DSTATCOM) are all new emerging devices aimed at regulating the reactive power requirements. The excellent controllability of these devices has paved the way to flexible and dynamic controllers that are capable of regulating the flow of active and reactive power components. These devices are now suggested for the control of the reactive power requirement of wind generators. Studies have demonstrated acceptable voltage stabilisation results. This has increased the penetration level of wind power into existing distribution networks in many countries. (Author)

An introduction to reactive power compensation for wind farms

International Nuclear Information System (INIS)

Nigim, K.A.; Cairo Univ., Giza; Zobaa, A.F.; El Amin, I.

2005-01-01

The paper summarises the refereed contributions of seven articles reviewed for publication in the IJETP - Special Issue on 'Reactive compensation for wind farms'. The main goal of the special issue is to provide a forum to exchange information on the reactive power compensation requirements for wind farms and introducing possible price mechanisms for today's deregulated power industry. Uncompensated reactive power causes stress on the hosting utility grid as well as added expenses, which create in difficulties for power purchasing agreements from independent wind energy producers. Wind power producers need to comply with the hosting utility grid interconnection standards, e.g., voltage and frequency, as well as to provide controllable active and reactive sources of power. Active power supply is mainly dependent on the potential of wind power produced and the turbine design. Reactive power demand on the other hand depends on the conversion devices and the recovered power quantity fed to the grid. Static Var Compensators (SVC), Unified Power Quality Conditioners (UPQC), Unified Power Flow Controllers (UPFC), and the Distributed Static Synchronous Compensators (DSTATCOM) are all new emerging devices aimed at regulating the reactive power requirements. The excellent controllability of these devices has paved the way to flexible and dynamic controllers that are capable of regulating the flow of active and reactive power components. These devices are now suggested for the control of the reactive power requirement of wind generators. Studies have demonstrated acceptable voltage stabilisation results. This has increased the penetration level of wind power into existing distribution networks in many countries. (Author)

The iodine reactivity

International Nuclear Information System (INIS)

2003-01-01

The iodine is an important element because it has long life isotopes (such as iodine 129) and a great mobility in natural media. Iodine presents a complex chemistry because of its volatility and its strong redox reactivity. The S.E.C.R. works to better understand the reactivity of this element in different natural, industrial or biological environments. It plays a part in thermochemical sites as a possible way of hydrogen formation. This seminar gives some aspects relative to the chemical reactivity of iodine, since its thermochemistry in the I/S cycles to produce hydrogen to its reactivity in the natural medium and its potential radiological impact. This document includes 4 presentations transparencies) dealing with: the 129 I cycle rejected in the low radioactive gaseous and liquid effluents of the La Hague reprocessing plant (C. Frechou); a bibliographic review of iodine retention in soils (F. Bazer-Bachi); the hydrogen production and the iodine/sulfur thermochemical cycle (role of iodine in the process); and the direct characterization by electro-spray ionization mass spectroscopy of iodine fixation by fulvic acids (P. Reiller, B. Amekraz, C. Moulin, V. Moulin)

Chlorination and chloramination of aminophenols in aqueous solution: oxidant demand and by-product formation.

Science.gov (United States)

Mehrez, O Abou; Dossier-Berne, F; Legube, B

2015-01-01

Chlorination and monochloramination of aminophenols (AP) were carried out in aqueous solution at 25°C and at pH 8.5. Oxidant demand and disinfection by-product formation were determined in excess of oxidant. Experiments have shown that chlorine consumption of AP was 40-60% higher than monochloramine consumption. Compared with monochloramination, chlorination of AP formed more chloroform and haloacetic acids (HAA). Dichloroacetic acid was the major species of HAA. Chloroform and HAA represented, respectively, only 1-8% and 14-15% of adsorbable organic halides (AOX) by monochloramination but up to 29% and 39% of AOX by chlorination.

Reactive power compensator

Science.gov (United States)

El-Sharkawi, Mohamed A.; Venkata, Subrahmanyam S.; Chen, Mingliang; Andexler, George; Huang, Tony

1992-01-01

A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation.

Reactive power compensator

Energy Technology Data Exchange (ETDEWEB)

El-Sharkawi, Mohamed A. (Renton, WA); Venkata, Subrahmanyam S. (Woodinville, WA); Chen, Mingliang (Kirkland, WA); Andexler, George (Everett, WA); Huang, Tony (Seattle, WA)

1992-01-01

A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation.

Memory for shape reactivates the lateral occipital complex.

Science.gov (United States)

Karanian, Jessica M; Slotnick, Scott D

2015-04-07

Memory is thought to be a constructive process in which the cortical regions associated with processing event features are reactivated during retrieval. Although there is evidence for non-detailed cortical reactivation during retrieval (e.g., memory for visual or auditory information reactivates the visual or auditory processing regions, respectively), there is limited evidence that memory can reactivate cortical regions associated with processing detailed, feature-specific information. Such evidence is critical to our understanding of the mechanisms of episodic retrieval. The present functional magnetic resonance imaging (fMRI) study assessed whether the lateral occipital complex (LOC), a region that preferentially processes shape, is associated with retrieval of shape information. During encoding, participants were presented with colored abstract shapes that were either intact or scrambled. During retrieval, colored disks were presented and participants indicated whether the corresponding shape was previously "intact" or "scrambled". To assess whether conscious retrieval of intact shapes reactivated LOC, we conducted a conjunction of shape perception/encoding and accurate versus inaccurate retrieval of intact shapes, which produced many activations in LOC. To determine whether activity in LOC was specific to intact shapes, we conducted a conjunction of shape perception/encoding and intact versus scrambled shapes, which also produced many activations in LOC. Furthermore, memory for intact shapes in each hemifield produced contralateral activity in LOC (e.g., memory for left visual field intact shapes activated right LOC), which reflects the specific reinstatement of perception/encoding activity. The present results extend previous feature-specific memory reactivation evidence and support the view that memory is a constructive process. Copyright © 2015 Elsevier B.V. All rights reserved.

Determination of the Effects of Medium Composition on the Monochloramine Disinfection Kinetics of Nitrosomonas europaea by the Propidium Monoazide Quantitative PCR and Live/Dead BacLight Methods ▿

Science.gov (United States)

Wahman, David G.; Schrantz, Karen A.; Pressman, Jonathan G.

2010-01-01

Various medium compositions (phosphate, 1 to 50 mM; ionic strength, 2.8 to 150 meq/liter) significantly affected Nitrosomonas europaea monochloramine disinfection kinetics, as determined by the Live/Dead BacLight (LD) and propidium monoazide quantitative PCR (PMA-qPCR) methods (lag coefficient, 37 to 490 [LD] and 91 to 490 [PMA-qPCR] mg·min/liter; Chick-Watson rate constant, 4.0 × 10−3 to 9.3 × 10−3 [LD] and 1.6 × 10−3 to 9.6 × 10−3 [PMA-qPCR] liter/mg·min). Two competing effects may account for the variation in disinfection kinetic parameters: (i) increasing kinetics (disinfection rate constant [k] increased, lag coefficient [b] decreased) with increasing phosphate concentration and (ii) decreasing kinetics (k decreased, b increased) with increasing ionic strength. The results support development of a standard medium for evaluating disinfection kinetics in drinking water. PMID:20952645

A Tariff for Reactive Power

Energy Technology Data Exchange (ETDEWEB)

Kueck, John D [ORNL; Kirby, Brendan J [ORNL; Li, Fangxing [ORNL; Tufon, Christopher [Pacific Gas and Electric Company; Isemonger, Alan [California Independent System Operator

2008-07-01

Two kinds of power are required to operate an electric power system: real power, measured in watts, and reactive power, measured in volt-amperes reactive or VARs. Reactive power supply is one of a class of power system reliability services collectively known as ancillary services, and is essential for the reliable operation of the bulk power system. Reactive power flows when current leads or lags behind voltage. Typically, the current in a distribution system lags behind voltage because of inductive loads such as motors. Reactive power flow wastes energy and capacity and causes voltage droop. To correct lagging power flow, leading reactive power (current leading voltage) is supplied to bring the current into phase with voltage. When the current is in phase with voltage, there is a reduction in system losses, an increase in system capacity, and a rise in voltage. Reactive power can be supplied from either static or dynamic VAR sources. Static sources are typically transmission and distribution equipment, such as capacitors at substations, and their cost has historically been included in the revenue requirement of the transmission operator (TO), and recovered through cost-of-service rates. By contrast, dynamic sources are typically generators capable of producing variable levels of reactive power by automatically controlling the generator to regulate voltage. Transmission system devices such as synchronous condensers can also provide dynamic reactive power. A class of solid state devices (called flexible AC transmission system devices or FACTs) can provide dynamic reactive power. One specific device has the unfortunate name of static VAR compensator (SVC), where 'static' refers to the solid state nature of the device (it does not include rotating equipment) and not to the production of static reactive power. Dynamic sources at the distribution level, while more costly would be very useful in helping to regulate local voltage. Local voltage regulation would

Microstructural characterization of copper based alloys produced by reactive milling; caracterizacion microestructural de aleaciones base cobre obtenidas mediante molienda reactiva

Energy Technology Data Exchange (ETDEWEB)

Palma, R.; Sepulveda, A.; Zuniga, A.; Donoso, E.; Dianez, M. J.; Criado, J. M.

2010-07-01

The micro and nano structure of Cu-Al, Cu-V and Cu-Ti alloys produced by reactive milling were analyzed using X-ray diffraction (XRD) and transmission electron microscopy (TEM). Samples with different milling times (t= 0, 10, 20 and 30 h) were considered. The grain size, dislocation density and residual micro strain were evaluated form the XRD data using the Williamson-Hall and Klug-Alexander methods. The evolution of texture as a function of milling time was also studied using XRD. It was found, using TEM, that the grain size and dispersoid size were nano metric in all three alloys considered. (Author) 12 refs.

A proposed abiotic reaction scheme for hydroxylamine and monochloramine under chloramination relevant drinking water conditions.

Science.gov (United States)

Wahman, David G; Speitel, Gerald E; Machavaram, Madhav V

2014-09-01

Drinking water monochloramine (NH2Cl) use may promote ammonia-oxidizing bacteria (AOB). AOB use (i) ammonia monooxygenase for biological ammonia (NH3) oxidation to hydroxylamine (NH2OH) and (ii) hydroxylamine oxidoreductase for NH2OH oxidation to nitrite. NH2Cl and NH2OH may react, providing AOB potential benefits and detriments. The NH2Cl/NH2OH reaction would benefit AOB by removing the disinfectant (NH2Cl) and releasing their growth substrate (NH3), but the NH2Cl/NH2OH reaction would also provide a possible additional inactivation mechanism besides direct NH2Cl reaction with cells. Because biological NH2OH oxidation supplies the electrons required for biological NH3 oxidation, the NH2Cl/NH2OH reaction provides a direct mechanism for NH2Cl to inhibit NH3 oxidation, starving the cell of reductant by preventing biological NH2OH oxidation. To investigate possible NH2Cl/NH2OH reaction implications on AOB, an understanding of the underlying abiotic reaction is first required. The present study conducted a detailed literature review and proposed an abiotic NH2Cl/NH2OH reaction scheme (RS) for chloramination relevant drinking water conditions (μM concentrations, air saturation, and pH 7-9). Next, RS literature based kinetics and end-products were evaluated experimentally between pHs 7.7 and 8.3, representing (i) the pH range for future experiments with AOB and (ii) mid-range pHs typically found in chloraminated drinking water. In addition, a (15)N stable isotope experiment was conducted to verify nitrous oxide and nitrogen gas production and their nitrogen source. Finally, the RS was slightly refined using the experimental data and an AQUASIM implemented kinetic model. A chloraminated drinking water relevant RS is proposed and provides the abiotic reaction foundation for future AOB biotic experiments. Published by Elsevier Ltd.

Pulsed EPR studies of small reactive radicals produced by ionizing radiation

International Nuclear Information System (INIS)

Lawler, R.G.

1985-01-01

For several years we have participated in a collaborative research effort to apply the pulsed EPR-pulse radiolysis technique to several problems associated with the dynamics of small reactive radicals formed during radiolysis of aqueous solutions using 3 MeV electrons from a Van de Graaff accelerator. We will discuss experimental techniques and applications arising from this work, with particular emphasis on problems requiring high initial radical concentrations and EPR time resolution of one microsecond or better. 2 figs., 2 tabs

Using exomarkers to assess mitochondrial reactive species in vivo.

Science.gov (United States)

Logan, Angela; Cochemé, Helena M; Li Pun, Pamela Boon; Apostolova, Nadezda; Smith, Robin A J; Larsen, Lesley; Larsen, David S; James, Andrew M; Fearnley, Ian M; Rogatti, Sebastian; Prime, Tracy A; Finichiu, Peter G; Dare, Anna; Chouchani, Edward T; Pell, Victoria R; Methner, Carmen; Quin, Caroline; McQuaker, Stephen J; Krieg, Thomas; Hartley, Richard C; Murphy, Michael P

2014-02-01

The ability to measure the concentrations of small damaging and signalling molecules such as reactive oxygen species (ROS) in vivo is essential to understanding their biological roles. While a range of methods can be applied to in vitro systems, measuring the levels and relative changes in reactive species in vivo is challenging. One approach towards achieving this goal is the use of exomarkers. In this, exogenous probe compounds are administered to the intact organism and are then transformed by the reactive molecules in vivo to produce a diagnostic exomarker. The exomarker and the precursor probe can be analysed ex vivo to infer the identity and amounts of the reactive species present in vivo. This is akin to the measurement of biomarkers produced by the interaction of reactive species with endogenous biomolecules. Our laboratories have developed mitochondria-targeted probes that generate exomarkers that can be analysed ex vivo by mass spectrometry to assess levels of reactive species within mitochondria in vivo. We have used one of these compounds, MitoB, to infer the levels of mitochondrial hydrogen peroxide within flies and mice. Here we describe the development of MitoB and expand on this example to discuss how better probes and exomarkers can be developed. This article is part of a Special Issue entitled Current methods to study reactive oxygen species - pros and cons and biophysics of membrane proteins. Guest Editor: Christine Winterbourn. Copyright © 2013 The Authors. Published by Elsevier B.V. All rights reserved.

Latent Virus Reactivation: From Space to Earth

Science.gov (United States)

Mehta, Satish K.; Cohrs, Randall J.; Gilden, Donald H.; Tyring, Stephen K.; Castro, Victoria A.; Ott, C. Mark; Pierson, Duane L.

2010-01-01

Reactivation of latent viruses is a recognized consequence of decreased immunity. More recently viral reactivation has been identified as an important in vivo indicator of clinically relevant immune changes. Viral reactivation can be determined quickly and easily by the presence of virus in saliva and other body fluids. Real-time polymerase chain reaction (PCR) is a highly sensitive and specific molecular method to detect the presence of specific viral DNA. Studies in astronauts demonstrated that herpes simplex virus type 1(HSV-1), Epstein-Barr Virus (EBV), cytomegalovirus (CMV), and varicella zoster virus (VZV) reactivate at rates above normal during and after spaceflight in response to moderately decreased T-cell immunity. This technology was expanded to patients on Earth beginning with human immune deficiency virus (HIV) immuno-compromised patients. The HIV patients shed EBV in saliva at rates 9-fold higher than observed in astronauts demonstrating that the level of EBV shedding reflects the severity of impaired immunity. Whereas EBV reactivation is not expected to produce serious effects in astronauts on missions of 6 months or less, VZV reactivation in astronauts could produce shingles. Reactivation of live, infectious VZV in astronauts with no symptoms was demonstrated in astronauts during and after spaceflight. We applied our technology to study VZV-induced shingles in patients. In a study of 54 shingles patients, we showed salivary VZV was present in every patient on the day antiviral (acyclovir) treatment was initiated. Pain and skin lesions decreased with antiviral treatment. Corresponding decreases in levels of VZV were also observed and accompanied recovery. Although the level of VZV in shingles patients before the treatment was generally higher than those found in astronauts, lower range of VZV numbers in shingles patients overlapped with astronaut s levels. This suggests a potential risk of shingles to astronauts resulting from reactivation of VZV. In

Reactivity margins in heavy water moderated production reactors

International Nuclear Information System (INIS)

Benton, F.D.

1981-11-01

The design of the reactor core and components of the heavy water moderated reactors at the Savannah River Plant (SFP) can be varied to produce a number of isotopes. For the past decade, the predominant reactor core design has been the enriched-depleted lattice. In this lattice, fuel assemblies of highly enriched uranium and target assemblies of depleted uranium, which produce plutonium, occupy alternate lattice positions. This heterogeneous lattice arrangement and a nonuniform control rod distribution result in a reactor core that requires sophisticated calculational methods for accurate reactivity margin and power distribution predictions. For maximum accuracy, techniques must exist to provide a base of observed data for the calculations. Frequent enriched-depleted lattice design changes are required as product demands vary. These changes provided incentive for the development of techniques to combine the results of calculations and observed reactivity data to accurately and conveniently monitor reactivity margins during operation

Glutamine supplementation suppresses herpes simplex virus reactivation.

Science.gov (United States)

Wang, Kening; Hoshino, Yo; Dowdell, Kennichi; Bosch-Marce, Marta; Myers, Timothy G; Sarmiento, Mayra; Pesnicak, Lesley; Krause, Philip R; Cohen, Jeffrey I

2017-06-30

Chronic viral infections are difficult to treat, and new approaches are needed, particularly those aimed at reducing reactivation by enhancing immune responses. Herpes simplex virus (HSV) establishes latency and reactivates frequently, and breakthrough reactivation can occur despite suppressive antiviral therapy. Virus-specific T cells are important to control HSV, and proliferation of activated T cells requires increased metabolism of glutamine. Here, we found that supplementation with oral glutamine reduced virus reactivation in latently HSV-1-infected mice and HSV-2-infected guinea pigs. Transcriptome analysis of trigeminal ganglia from latently HSV-1-infected, glutamine-treated WT mice showed upregulation of several IFN-γ-inducible genes. In contrast to WT mice, supplemental glutamine was ineffective in reducing the rate of HSV-1 reactivation in latently HSV-1-infected IFN-γ-KO mice. Mice treated with glutamine also had higher numbers of HSV-specific IFN-γ-producing CD8 T cells in latently infected ganglia. Thus, glutamine may enhance the IFN-γ-associated immune response and reduce the rate of reactivation of latent virus infection.

Immune reactivities against gums.

Science.gov (United States)

Vojdani, Aristo; Vojdani, Charlene

2015-01-01

Different kinds of gums from various sources enjoy an extremely broad range of commercial and industrial use, from food and pharmaceuticals to printing and adhesives. Although generally recognized as safe by the US Food and Drug Administration (FDA), gums have a history of association with sensitive or allergic reactions. In addition, studies have shown that gums have a structural, molecular similarity to a number of common foods. A possibility exists for cross-reactivity. Due to the widespread use of gums in almost every aspect of modern life, the overall goal of the current investigation was to determine the degree of immune reactivity to various gum antigens in the sera of individuals representing the general population. The study was a randomized, controlled trial. 288 sera purchased from a commercial source. The sera was screened for immunoglobulin G (IgG) and immunoglobulin E (IgE) antibodies against extracts of mastic gum, carrageenan, xantham gum, guar gum, gum tragacanth, locust bean gum, and β-glucan, using indirect enzyme-linked immunosorbent assay (ELISA) testing. For each gum antigen, inhibition testing was performed on the 4 sera that showed the highest IgG and IgE immune reactivity against the different gums used in the study. Inhibition testing on these same sera for sesame albumin, lentil, corn, rice, pineapple, peanut, pea protein, shrimp, or kidney bean was used to determine the cross-reactivity of these foods with the gum. Of the 288 samples, 4.2%-27% of the specimens showed a significant elevation in IgG antibodies against various gums. Only 4 of 288, or 1.4%, showed a simultaneous elevation of the IgG antibody against all 7 gum extracts. For the IgE antibody, 15.6%-29.1% of the specimens showed an elevation against the various gums. A significant percentage of the specimens, 12.8%, simultaneously produced IgE antibodies against all 7 tested extracts. Overall, the percentage of elevation in IgE antibodies against different gum extracts, with

Soot Reactivity in Conventional Combustion and Oxy-fuel Combustion Environments

DEFF Research Database (Denmark)

Abián, María; Jensen, Anker D.; Glarborg, Peter

2012-01-01

A study of the reactivity of soot produced from ethylene pyrolysis at different temperatures and CO2 atmospheres toward O2 and CO2 has been carried out using a thermogravimetric analyzer. The purpose was to quantify how soot reactivity is affected by the gas environment and temperature history of...

Reactive Sintering of Bimodal WC-Co Hardmetals

Directory of Open Access Journals (Sweden)

Marek Tarraste

2015-09-01

Full Text Available Bimodal WC-Co hardmetals were produced using novel technology - reactive sintering. Milled and activated tungsten and graphite powders were mixed with commercial coarse grained WC-Co powder and then sintered. The microstructure of produced materials was free of defects and consisted of evenly distributed coarse and fine tungsten carbide grains in cobalt binder. The microstructure, hardness and fracture toughness of reactive sintered bimodal WC-Co hardmetals is exhibited. Developed bimodal hardmetal has perspective for demanding wear applications for its increased combined hardness and toughness. Compared to coarse material there is only slight decrease in fracture toughness (K1c is 14.7 for coarse grained and 14.4 for bimodal, hardness is increased from 1290 to 1350 HV units.DOI: http://dx.doi.org/10.5755/j01.ms.21.3.7511

Laboratory and field scale demonstration of reactive barrier systems

International Nuclear Information System (INIS)

Dwyer, B.P.; Marozas, D.C.; Cantrell, K.; Stewart, W.

1996-10-01

In an effort to devise a cost efficient technology for remediation of uranium contaminated groundwater, the Department of Energy's Uranium Mill Tailings Remedial Action (DOE-UMTRA) Program through Sandia National Laboratories (SNL) fabricated a pilot scale research project utilizing reactive subsurface barriers at an UMTRA site in Durango, Colorado. A reactive subsurface barrier is produced by placing a reactant material (in this experiment, metallic iron) in the flow path of the contaminated groundwater. The reactive media then removes and/or transforms the contaminant(s) to regulatory acceptable levels. Experimental design and results are discussed with regard to other potential applications of reactive barrier remediation strategies at other sites with contaminated groundwater problems

Influence of deposition parameters on the optical and structural properties of TiO/sub 2/ films produced by reactive dc plasmatron sputtering

Energy Technology Data Exchange (ETDEWEB)

Schiller, S; Beister, G; Sieber, W; Schirmer, G; Hacker, E

1981-09-11

We investigated the variations in the structure and optical properties of TiO/sub 2/ films produced by reactive d.c. plasmatron sputtering with the most important deposition parameters. Over a wide range, the phase composition (ratio of rutile to anatase) and the grain size of the TiO/sub 2/ films can be influenced in a controlled manner by variations in the substrate temperature and the oxygen partial pressure. Because of their high refractive index and low light-scattering losses, plasmatron-sputtered TiO/sub 2/ films are of great interest in the field of optical interference coatings, e.g. for dielectric multilayer stacks.

Reactive modification of polyesters and their blends

Science.gov (United States)

Wan, Chen

2004-12-01

the desired rheological and structural characteristics of the final products for potential applications such as low density extrusion foaming or compatibilization of immiscible polymer blends. Important modification conditions through coagents are identified and reaction mechanisms are proposed. A high MW saturated polyester, PET, can also be rheologically modified in extruders through low MW multifunctional anhydride and epoxy compounds by chain extension/branching. Several such modifiers were successfully screened in terms of their reactivity towards PET under controlled reactive extrusion conditions. A dianhydride with medium reactivity was then successfully used in a one-step reactive modification/extrusion foaming process to produce low density foams. A similar process was successfully used to produce small cell size foams from a four component system containing PET, PP and lesser amounts of a low molecular weight multifunctional epoxy compound and an acid functionalized polyolefin, the latter acting as compatibilizers.

Aqueous chemistry of chlorine: chemistry, analysis, and environmental fate of reactive oxidant species

Energy Technology Data Exchange (ETDEWEB)

Jolley, R.L.; Carpenter, J.H.

1982-01-01

This report reviews (1) the chemistry of chlorine relative to its reactions in fresh, estuarine, and marine waters and the formation of reactive oxidant species; (2) the current status of chemical analysis of reactive chlorine species and chlorine-produced oxidant species relative to analysis of low concentrations (microgram-per-liter range) and determination of accuracy and precision of methods; and (3) the environmental fate of chlorine and chlorine-produced oxidant species.

Formation of emerging DBPs from the chlorination and chloramination of seawater algal organic matter and related model compounds

KAUST Repository

Nihemaiti, Maolida

2014-05-01

chloramination of aromatic compounds (i.e., phenol and resorcinol) indicating that N-DBPs can also be formed from organic compounds without any organic nitrogen through the incorporation of inorganic nitrogen from monochloramine. Moreover, results from Hymenomonas sp., aromatic amino acids, and phenolic compounds suggested that aromatic compounds are highly reactive with monochloramine and a major fraction of DBP precursors.

A study of temperature coefficients of reactivity for a Savannah River Site tritium-producing charge

International Nuclear Information System (INIS)

George, D.L.; Frost, R.L.

1991-01-01

Temperature coefficients of reactivity have been calculated for the Mark 22 assembly in the K-14 charge at the Savannah River Site. Temperature coefficients are the most important reactivity feedback mechanism in SRS reactors; they are used in all safety analyses performed in support of the Safety Analysis Report, and in operations to predict reactivity changes with control rod moves. The effects of the radial location of the assembly in the reactor, isotope depletion, and thermal expansion of the metal components on the temperature coefficients have also been investigated. With the exception of the dead space coefficient, all of the regional temperature coefficients were found to be negative or zero. All of the temperature coefficients become more negative with isotopic depletion over the fuel cycle. Coefficients also become more negative with increasing radial distance of the assembly from the center of the core; this is proven from first principles and confirmed by calculations. It was found that axial and radial thermal expansion effects on the metal fuel and target tubes counteract one another, indicating these effects do not need to be considered in future temperature coefficient calculations for the Mark 22 assembly. The moderator coefficient was found to be nonlinear with temperature; thus, the values derived for accidents involving increases in moderator temperature are significantly different than those for decreases in moderator temperature, although the moderator coefficient is always negative

NDMA formation by chloramination of ranitidine: Kinetics and mechanism

KAUST Repository

Le Roux, Julien

2012-10-16

The kinetics of decomposition of the pharmaceutical ranitidine (a major precursor of NDMA) during chloramination was investigated and some decomposition byproducts were identified by using high performance liquid chromatography coupled with mass spectrometry (HPLC-MS). The reaction between monochloramine and ranitidine followed second order kinetics and was acid-catalyzed. Decomposition of ranitidine formed different byproducts depending on the applied monochloramine concentration. Most identified products were chlorinated and hydroxylated analogues of ranitidine. In excess of monochloramine, nucleophilic substitution between ranitidine and monochloramine led to byproducts that are critical intermediates involved in the formation of NDMA, for example, a carbocation formed from the decomposition of the methylfuran moiety of ranitidine. A complete mechanism is proposed to explain the high formation yield of NDMA from chloramination of ranitidine. These results are of great importance to understand the formation of NDMA by chloramination of tertiary amines. © 2012 American Chemical Society.

Numerical Simulations of High Reactivity Gasoline Fuel Sprays under Vaporizing and Reactive Conditions

KAUST Repository

Mohan, Balaji; Jaasim, Mohammed; Ahmed, Ahfaz; Hernandez Perez, Francisco; Sim, Jaeheon; Roberts, William L.; Sarathy, Mani; Im, Hong G.

2018-01-01

Gasoline compression ignition (GCI) engines are becoming more popular alternative for conventional spark engines to harvest the advantage of high volatility. Recent experimental study demonstrated that high reactivity gasoline fuel can be operated in a conventional mixing controlled combustion mode producing lower soot emissions than that of diesel fuel under similar efficiency and NOx level [1]. Therefore, there is much interest in using gasoline-like fuels in compression ignition engines. In order to improve the fidelity of simulation-based GCI combustion system development, it is mandatory to enhance the prediction of spray combustion of gasoline-like fuels. The purpose of this study is to model the spray characteristics of high reactivity gasoline fuels and validate the models with experimental results obtained through an optically accessible constant volume vessel under vaporizing [2] and reactive conditions [3]. For reacting cases, a comparison of PRF and KAUST multi-component surrogate (KMCS) mechanism was done to obtain good agreement with the experimental ignition delay. From this study, some recommendations were proposed for GCI combustion modelling framework using gasoline like fuels.

Numerical Simulations of High Reactivity Gasoline Fuel Sprays under Vaporizing and Reactive Conditions

KAUST Repository

Mohan, Balaji

2018-04-03

Gasoline compression ignition (GCI) engines are becoming more popular alternative for conventional spark engines to harvest the advantage of high volatility. Recent experimental study demonstrated that high reactivity gasoline fuel can be operated in a conventional mixing controlled combustion mode producing lower soot emissions than that of diesel fuel under similar efficiency and NOx level [1]. Therefore, there is much interest in using gasoline-like fuels in compression ignition engines. In order to improve the fidelity of simulation-based GCI combustion system development, it is mandatory to enhance the prediction of spray combustion of gasoline-like fuels. The purpose of this study is to model the spray characteristics of high reactivity gasoline fuels and validate the models with experimental results obtained through an optically accessible constant volume vessel under vaporizing [2] and reactive conditions [3]. For reacting cases, a comparison of PRF and KAUST multi-component surrogate (KMCS) mechanism was done to obtain good agreement with the experimental ignition delay. From this study, some recommendations were proposed for GCI combustion modelling framework using gasoline like fuels.

Comparison of techniques of detecting immunoglobulin-binding protein reactivity to immunoglobulin produced by different avian and mammalian species.

Science.gov (United States)

Justiz-Vaillant, A A; Akpaka, P E; McFarlane-Anderson, N; Smikle, M F

2013-01-01

The rationale of this study was to use several immunological assays to investigate the reactivity of immunoglobulin binding protein (IBP) to immunoglobulins from various avian and mammalian species. The IBP studied were Staphylococcal protein A (SpA), Streptococcal protein G (SpG), Peptostreptococcal protein L (SpL) and recombinant protein LA (SpLA). The various immunological techniques used were double immunodiffusion (Ouchterlony technique) that tested positive high protein reactivities, direct and competitive enzyme-linked immunosorbent assays (ELISAs) that tested moderate and low positive protein binding capacities, respectively. In addition to sandwich ELISAs, immunoblot analyses and Ig-purification by SpA-affinity chromatography, which were sensitive tests and helpful in the screening and confirmatory tests were also used. The Ouchterlony technique showed that compared to the other proteins, SpLA had the highest range of reactivity with animal sera and purified immunoglobulins while SpL was least reactive. With the direct ELISA, SpL reacted with the raccoon sera, rabbit IgG and with IgY from bantam hens and pigeons. While with the direct ELISA, SpA reacted with sera from skunk, coyote, raccoon, mule, donkey and human. The sandwich ELISA revealed high reactivity of both SpG and SpLA with mammalian sera titres ranging from 1:32 (raccoon serum) to 1:1024 (mule and donkey sera). These results suggest that IBP can be used for the detection of immunoglobulin using various immunological assays and this is important for the diagnosis of infectious diseases in animal and bird populations studied and in the purification of immunoglobulins.

The reactivity meter and core reactivity

International Nuclear Information System (INIS)

Siltanen, P.

1999-01-01

This paper discussed in depth the point kinetic equations and the characteristics of the point kinetic reactivity meter, particularly for large negative reactivities. From a given input signal representing the neutron flux seen by a detector, the meter computes a value of reactivity in dollars (ρ/β), based on inverse point kinetics. The prompt jump point of view is emphasised. (Author)

Reactivation hazard mapping for ancient landslides in West Belgium

Directory of Open Access Journals (Sweden)

O. Dewitte

2006-01-01

Full Text Available Several examples in western Europe have shown that, at least for deep-seated rotational slides, reactivation of formerly slipped masses is a more frequent phenomenon than the occurrence of new landslides, therefore representing a higher hazard. We selected a study area comprised of 13 landslides located in the Flemish Ardennes (West Belgium and predicted the hazard related to scarp retreat. The scarp reactivations were identified from the comparison of DTMs produced for 1952 and 1996. Robust results were obtained with the Gamma operator of a fuzzy set approach and a combination of geomorphic, topographic and land use data. We built first a prediction model from the relations linking the 1952–1996 retreat events to the conditioning parameters of 1952. The prediction rate of the resulting susceptibility map is estimated by a cross-validation procedure. We then applied the statistics of this model to the data of 1996 in order to produce a susceptibility map responding to the present-day conditions. Finally, we estimated the conditional probabilities of occurrence of future reactivations for the period 1996–2036.

Oxidants, Antioxidants, and the Beneficial Roles of Exercise-Induced Production of Reactive Species

Directory of Open Access Journals (Sweden)

Elisa Couto Gomes

2012-01-01

Full Text Available This review offers an overview of the influence of reactive species produced during exercise and their effect on exercise adaptation. Reactive species and free radicals are unstable molecules that oxidize other molecules in order to become stable. Although they play important roles in our body, they can also lead to oxidative stress impairing diverse cellular functions. During exercise, reactive species can be produced mainly, but not exclusively, by the following mechanisms: electron leak at the mitochondrial electron transport chain, ischemia/reperfusion and activation of endothelial xanthine oxidase, inflammatory response, and autooxidation of catecholamines. Chronic exercise also leads to the upregulation of the body's antioxidant defence mechanism, which helps minimize the oxidative stress that may occur after an acute bout of exercise. Recent studies show a beneficial role of the reactive species, produced during a bout of exercise, that lead to important training adaptations: angiogenesis, mitochondria biogenesis, and muscle hypertrophy. The adaptations occur depending on the mechanic, and consequently biochemical, stimulus within the muscle. This is a new area of study that promises important findings in the sphere of molecular and cellular mechanisms involved in the relationship between oxidative stress and exercise.

Oxidants, Antioxidants, and the Beneficial Roles of Exercise-Induced Production of Reactive Species

Science.gov (United States)

Gomes, Elisa Couto; Silva, Albená Nunes; de Oliveira, Marta Rubino

2012-01-01

This review offers an overview of the influence of reactive species produced during exercise and their effect on exercise adaptation. Reactive species and free radicals are unstable molecules that oxidize other molecules in order to become stable. Although they play important roles in our body, they can also lead to oxidative stress impairing diverse cellular functions. During exercise, reactive species can be produced mainly, but not exclusively, by the following mechanisms: electron leak at the mitochondrial electron transport chain, ischemia/reperfusion and activation of endothelial xanthine oxidase, inflammatory response, and autooxidation of catecholamines. Chronic exercise also leads to the upregulation of the body's antioxidant defence mechanism, which helps minimize the oxidative stress that may occur after an acute bout of exercise. Recent studies show a beneficial role of the reactive species, produced during a bout of exercise, that lead to important training adaptations: angiogenesis, mitochondria biogenesis, and muscle hypertrophy. The adaptations occur depending on the mechanic, and consequently biochemical, stimulus within the muscle. This is a new area of study that promises important findings in the sphere of molecular and cellular mechanisms involved in the relationship between oxidative stress and exercise. PMID:22701757

Characterization and reactivity of soot from fast pyrolysis of lignocellulosic compounds and monolignols

DEFF Research Database (Denmark)

Trubetskaya, Anna; Brown, Avery; Tompsett, Geoffrey

2018-01-01

spectroscopy. The CO2 reactivity of soot was investigated by thermogravimetric analysis. Soot from cellulose was more reactive than soot produced from extractives, lignin and monolignols. Soot reactivity was correlated with the separation distances between adjacent graphene layers, as measured using...... transmission electron microscopy. Particle size, free radical concentration, differences in a degree of curvature and multi-core structures influenced the soot reactivity less than the interlayer separation distances. Soot yield was correlated with the lignin content of the feedstock. The selection...... of the extraction solvent had a strong influence on the soot reactivity. The Soxhlet extraction of softwood and wheat straw lignin soot using methanol decreased the soot reactivity, whereas acetone extraction had only a modest effect....

Reactive oxygen species produced by NADPH oxidase and mitochondrial dysfunction in lung after an acute exposure to Residual Oil Fly Ashes

Energy Technology Data Exchange (ETDEWEB)

Magnani, Natalia D.; Marchini, Timoteo; Vanasco, Virginia [Instituto de Bioquímica Medicina Molecular (IBIMOL-UBA-CONICET), Facultad de Farmacia y Bioquímica, Universidad de Buenos Aires, Buenos Aires (Argentina); Tasat, Deborah R. [CESyMA, Escuela de Ciencia y Tecnología, Universidad Nacional de San Martín, San Martín, Buenos Aires (Argentina); Alvarez, Silvia [Instituto de Bioquímica Medicina Molecular (IBIMOL-UBA-CONICET), Facultad de Farmacia y Bioquímica, Universidad de Buenos Aires, Buenos Aires (Argentina); Evelson, Pablo, E-mail: pevelson@ffyb.uba.ar [Instituto de Bioquímica Medicina Molecular (IBIMOL-UBA-CONICET), Facultad de Farmacia y Bioquímica, Universidad de Buenos Aires, Buenos Aires (Argentina)

2013-07-01

Reactive O{sub 2} species production triggered by particulate matter (PM) exposure is able to initiate oxidative damage mechanisms, which are postulated as responsible for increased morbidity along with the aggravation of respiratory diseases. The aim of this work was to quantitatively analyse the major sources of reactive O{sub 2} species involved in lung O{sub 2} metabolism after an acute exposure to Residual Oil Fly Ashes (ROFAs). Mice were intranasally instilled with a ROFA suspension (1.0 mg/kg body weight), and lung samples were analysed 1 h after instillation. Tissue O{sub 2} consumption and NADPH oxidase (Nox) activity were evaluated in tissue homogenates. Mitochondrial respiration, respiratory chain complexes activity, H{sub 2}O{sub 2} and ATP production rates, mitochondrial membrane potential and oxidative damage markers were assessed in isolated mitochondria. ROFA exposure was found to be associated with 61% increased tissue O{sub 2} consumption, a 30% increase in Nox activity, a 33% increased state 3 mitochondrial O{sub 2} consumption and a mitochondrial complex II activity increased by 25%. During mitochondrial active respiration, mitochondrial depolarization and a 53% decreased ATP production rate were observed. Neither changes in H{sub 2}O{sub 2} production rate, nor oxidative damage in isolated mitochondria were observed after the instillation. After an acute ROFA exposure, increased tissue O{sub 2} consumption may account for an augmented Nox activity, causing an increased O{sub 2}{sup ·−} production. The mitochondrial function modifications found may prevent oxidative damage within the organelle. These findings provide new insights to the understanding of the mechanisms involving reactive O{sub 2} species production in the lung triggered by ROFA exposure. - Highlights: • Exposure to ROFA alters the oxidative metabolism in mice lung. • The augmented Nox activity contributes to the high tissue O{sub 2} consumption. • Exposure to ROFA

The role of chloramine species in NDMA formation.

Science.gov (United States)

Selbes, Meric; Beita-Sandí, Wilson; Kim, Daekyun; Karanfil, Tanju

2018-09-01

N-nitrosodimethylamine (NDMA), a probable human carcinogen disinfection by-product, has been detected in chloraminated drinking water systems. Understanding its formation over time is important to control NDMA levels in distribution systems. The main objectives of this study were to investigate the role of chloramine species (i.e., monochloramine and dichloramine); and the factors such as pH, sulfate, and natural organic matter (NOM) influencing the formation of NDMA. Five NDMA precursors (i.e., dimethylamine (DMA), trimethylamine (TMA), N,N-dimethylisopropylamine (DMiPA), N,N-dimethylbenzylamine (DMBzA), and ranitidine (RNTD)) were carefully selected based on their chemical structures and exposed to varying ratios of monochloramine and dichloramine. All amine precursors reacted relatively fast to form NDMA and reached their maximum NDMA yields within 24 h in the presence of excess levels of chloramines (both mono- and dichloramine) or excess levels of dichloramine conditions (with limited monochloramine). When the formation of dichloramine was suppressed (i.e., only monochloramine existed in the system) over the 5 day contact time, NDMA formation from DMA, TMA, and DMiPA was drastically reduced (∼0%). Under monochloramine abundant conditions, however, DMBzA and RNTD showed 40% and 90% NDMA conversions at the end of 5 day contact time, respectively, with slow formation rates, indicating that while these amine precursors react preferentially with dichloramine to form NDMA, they can also react with monochloramine in the absence of dichloramine. NOM and pH influenced dichloramine levels that affected NDMA yields. NOM had an adverse effect on NDMA formation as it created a competition with NDMA precursors for dichloramine. Sulfate did not increase the NDMA formation from the two selected NDMA precursors. pH played a key role as it influenced both chloramine speciation and protonation state of amine precursors and the highest NDMA formation was observed at the p

Role of reactive species in the photocatalytic degradation of ...

Indian Academy of Sciences (India)

2017-12-06

Dec 6, 2017 ... Nitrogen doping; photocatalysis; visible light active; reactive species; ... Of a variety of semiconductors, tungsten oxide (WO3) ... sodium chloride (NaCl, Chameleon reagent), sodium nitrate ..... Ammonium. No ion .... produced.

C-reactive (CRP) protein in transfusion dependent thalassaemic patients

International Nuclear Information System (INIS)

Jokhio, R.; Mughal, Z.U.N.

2009-01-01

In thalassaemic patients iron overload, secondary to blood transfusion, results toxic effects by producing reactive radicals. Iron overload can be studied using serum ferritin level which has a direct correlation with the body's iron status. While oxidative damage can be studied using biomarker of inflammation like hsC-reactive proteins. Blood samples of 55 thalassaemic patients (39 males, 16 females) were collected from Fatmid Foundation (Hyderabad). The samples were analyzed for CBC, serum ferritin level and hsC-reactive proteins. High mean serum ferritin levels was found in all the patients regardless of the frequency of blood transfusion (4774.2135+-3143.3040 mu g/L), indicating the iron overload. High mean hsC-reactive protein was found (2.5151+-1.3712) with a positive correlation with ferritin (r= 0.8371198, p= 0.0000) and platelets (r= 0.43293443, p=0.000962175). C-reactive proteins serve as biomarker of various inflammatory conditions, progression of cardiovascular diseases and as indicator of morbidity and mortality. High C-reactive proteins in these patients indicate ongoing iron overload toxicity related damage in these patients. The estimation of hsC-reactive proteins and other biomarkers of inflammation and oxidation may help in better management of these patients. (author)

Identification of memory reactivation during sleep by EEG classification.

Science.gov (United States)

Belal, Suliman; Cousins, James; El-Deredy, Wael; Parkes, Laura; Schneider, Jules; Tsujimura, Hikaru; Zoumpoulaki, Alexia; Perapoch, Marta; Santamaria, Lorena; Lewis, Penelope

2018-04-17

Memory reactivation during sleep is critical for consolidation, but also extremely difficult to measure as it is subtle, distributed and temporally unpredictable. This article reports a novel method for detecting such reactivation in standard sleep recordings. During learning, participants produced a complex sequence of finger presses, with each finger cued by a distinct audio-visual stimulus. Auditory cues were then re-played during subsequent sleep to trigger neural reactivation through a method known as targeted memory reactivation (TMR). Next, we used electroencephalography data from the learning session to train a machine learning classifier, and then applied this classifier to sleep data to determine how successfully each tone had elicited memory reactivation. Neural reactivation was classified above chance in all participants when TMR was applied in SWS, and in 5 of the 14 participants to whom TMR was applied in N2. Classification success reduced across numerous repetitions of the tone cue, suggesting either a gradually reducing responsiveness to such cues or a plasticity-related change in the neural signature as a result of cueing. We believe this method will be valuable for future investigations of memory consolidation. Copyright © 2018 Elsevier Inc. All rights reserved.

DNA repair in B. subtilis: an inducible dimer-specific W-reactivation system

International Nuclear Information System (INIS)

Fields, P.I.; Yasbin, R.E.

1982-01-01

The W-reactivation system of Bacillus subtilis can repair pyrimidine dimers in bacteriophage DNA. This inducible repair system can be activated by treatment of the bacteria with uv, alkylating agents, cross-linking agents and gamma irradiation. However, bacteriophage treated with agents other than those that cause pyrimidine dimers to be produced was not repaired by this unique form of W-reactivation. In contrast, the W-reactivation system of Escherichia coli can repair a variety of damages placed in the bacteriophage DNA

Quick monitoring of pozzolanic reactivity of waste ashes.

Science.gov (United States)

Sinthaworn, Suppachai; Nimityongskul, Pichai

2009-05-01

This article proposes a quick method of monitoring for pozzolanic reactivity of waste ashes by investigating the electrical conductivity of the suspension at an elevated temperature. This suspension is obtained by mixing tested pozzolan with an ordinary Portland cement (OPC) solution produced by mixing ordinary Portland cement with water. For comparison, silica fume, metakaolin, rice husk ash and river sand - whose pozzolanic reactivities range from reactive to inert - were used in the experimental investigation. The electrical conductivity of the suspension was continually recorded by using an electrical conductivity meter and stored by using a personal computer for a period of slightly over 1day. The indicative parameters that can be related to pozzolanic reactivity were discussed and analyzed in detail. It was found that it is possible to determine the pozzolanic reactivity of fly ash within 28h by using the proposed technique, as compared to 7 or 28 days for the determination of strength activity index according to ASTM. This technique would help concrete technologists to speedily investigate the quality of fly ash for use as a cement replacement in order to alleviate pollution caused by cement production and solve disposal problems of waste ashes.

Generation of memory B cells and their reactivation.

Science.gov (United States)

Inoue, Takeshi; Moran, Imogen; Shinnakasu, Ryo; Phan, Tri Giang; Kurosaki, Tomohiro

2018-05-01

The successful establishment of humoral memory response depends on at least two layers of defense. Pre-existing protective antibodies secreted by long-lived plasma cells act as a first line of defense against reinfection ("constitutive humoral memory"). Previously, a second line of defense in which pathogen-experienced memory B cells are rapidly reactivated to produce antibodies ("reactive humoral memory"), was considered as simply a back-up system for the first line (particularly for re-infection with homologous viruses). However, in the case of re-infection with similar but different strains of viruses, or in response to viral escape mutants, the reactive humoral memory plays a crucial role. Here, we review recent progress in our understanding of how memory B cells are generated in the pre-GC stage and during the GC reaction, and how these memory B cells are robustly reactivated with the help of memory Tfh cells to generate the secondary antibody response. In addition, we discuss how these advances may be relevant to the quest for a vaccine that can induce broadly reactive antibodies against influenza and HIV. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Techniques for computing reactivity changes caused by fuel axial expansion in LMR's

International Nuclear Information System (INIS)

Khalil, H.

1988-01-01

An evaluation is made of the accuracy of methods used to compute reactivity changes caused by axial fuel relocation in fast reactors. Results are presented to demonstrate the validity of assumptions commonly made such as linearity of reactivity with fuel elongation, additivity of local reactivity contributions, and the adequacy of standard perturbation techniques. Accurate prediction of the reactivity loss caused by axial swelling of metallic fuel is shown to require proper representation of the burnup dependence of the expansion reactivity. Some accuracy limitations in the methods used in transient analyses, which are based on the use of fuel worth tables, are identified, and efficient ways to improve accuracy are described. Implementation of these corrections produced expansion reactivity estimates within 5% of higher-order method for a metal-fueled FFTF core representation. 18 refs., 3 figs., 3 tabs

Disassembly and reassembly of human papillomavirus virus-like particles produces more virion-like antibody reactivity

Directory of Open Access Journals (Sweden)

Zhao Qinjian

2012-02-01

Full Text Available Abstract Background Human papillomavirus (HPV vaccines based on major capsid protein L1 are licensed in over 100 countries to prevent HPV infections. The yeast-derived recombinant quadrivalent HPV L1 vaccine, GARDASIL(R, has played an important role in reducing cancer and genital warts since its introduction in 2006. The L1 proteins self-assemble into virus-like particles (VLPs. Results VLPs were subjected to post-purification disassembly and reassembly (D/R treatment during bioprocessing to improve VLP immunoreactivity and stability. The post-D/R HPV16 VLPs and their complex with H16.V5 neutralizing antibody Fab fragments were visualized by cryo electron microscopy, showing VLPs densely decorated with antibody. Along with structural improvements, post-D/R VLPs showed markedly higher antigenicity to conformational and neutralizing monoclonal antibodies (mAbs H16.V5, H16.E70 and H263.A2, whereas binding to mAbs recognizing linear epitopes (H16.J4, H16.O7, and H16.H5 was greatly reduced. Strikingly, post-D/R VLPs showed no detectable binding to H16.H5, indicating that the H16.H5 epitope is not accessible in fully assembled VLPs. An atomic homology model of the entire HPV16 VLP was generated based on previously determined high-resolution structures of bovine papillomavirus and HPV16 L1 pentameric capsomeres. Conclusions D/R treatment of HPV16 L1 VLPs produces more homogeneous VLPs with more virion-like antibody reactivity. These effects can be attributed to a combination of more complete and regular assembly of the VLPs, better folding of L1, reduced non-specific disulfide-mediated aggregation and increased stability of the VLPs. Markedly different antigenicity of HPV16 VLPs was observed upon D/R treatment with a panel of monoclonal antibodies targeting neutralization sensitive epitopes. Multiple epitope-specific assays with a panel of mAbs with different properties and epitopes are required to gain a better understanding of the immunochemical

Risk assessment of DNA-reactive carcinogens in food.

Science.gov (United States)

Jeffrey, A M; Williams, G M

2005-09-01

Risk assessment of DNA-reactive carcinogens in food requires knowledge of the extent of DNA damage in the target organ which results from the competition between DNA adduct formation and repair. Estimates of DNA adduct levels can be made by direct measurement or indirectly as a consequence of their presence, for example, by tumor formation in animal models or exposed populations epidemiologically. Food-borne DNA-reactive carcinogens are present from a variety of sources. They are generally not intrinsically DNA-reactive but require bioactivation to DNA-reactive metabolites a process which may be modulated by the compound itself or the presence of other xenobiotics. A single DNA reactant may form several distinct DNA adducts each undergoing different rates of repair. Some DNA reactants may be photochemically activated or produce reactive oxygen species and thus indirect oxidative DNA damage. The levels of DNA adducts arising from exposures influenced by variations in the doses, the frequency with which an individual is exposed, and rates of DNA repair for specific adducts. Each adduct has a characteristic efficiency with which it induces mutations. Based on experience with the well-studied DNA-reactive food carcinogen aflatoxin B(1) (AFB(1)), a limit of 20 ppb or approximately 30 microg/day has been set and is considered a tolerable daily intake (TDI). Since AFB(1) is considered a potent carcinogen, doses of carcinogens is made.

Method of reactivity control in pressure tube reactor

International Nuclear Information System (INIS)

Fukumura, Nobuo.

1988-01-01

Purpose: To provide a method of controlling reactivity in a pressure tube reactor at high conversion ratio intended for high burn-up degree. Method: Control tubes are inserted in heavy water moderator. Light water is filled in the tubes at the initial burning stage. Along with the advance of the burning, the light water is gradually removed and replaced with gases of less reactive nuclear reactivity with neutrons such as air or gaseous carbon dioxide. The tubes are made of less neutron absorbing material such as aluminum. By filling light water, infinite multiplication factor is reduced to suppress the reactivity at the initial burning stage. As light water is gradually removed and replaced with air, etc., it provides an effect like that elimination of heavy water moderator to increase the conversion ratio. Accordingly, nuclear fission materials are produced additionally by so much to extend the burn-up degree. In this way, it can provide excellent effect in realizing high burn-up ratio and high conversion ratio. (Kamimura, M.)

Synthesis and characterization of reactive dye-cassava mesocarp ...

African Journals Online (AJOL)

The synthesis of triazine based reactive dyes was carried out. The resultant dyes were characterized by thin layers chromatography, molecular weight, infrared and ultra- violet spectroscopy, and used in dyeing cassava mesocarp to produce dye modified cellulosic substrates. The dyed substrates were tested for dye fixation, ...

Risk assessment of DNA-reactive carcinogens in food

International Nuclear Information System (INIS)

Jeffrey, A.M.; Williams, G.M.

2005-01-01

Risk assessment of DNA-reactive carcinogens in food requires knowledge of the extent of DNA damage in the target organ which results from the competition between DNA adduct formation and repair. Estimates of DNA adduct levels can be made by direct measurement or indirectly as a consequence of their presence, for example, by tumor formation in animal models or exposed populations epidemiologically. Food-borne DNA-reactive carcinogens are present from a variety of sources. They are generally not intrinsically DNA-reactive but require bioactivation to DNA-reactive metabolites a process which may be modulated by the compound itself or the presence of other xenobiotics. A single DNA reactant may form several distinct DNA adducts each undergoing different rates of repair. Some DNA reactants may be photochemically activated or produce reactive oxygen species and thus indirect oxidative DNA damage. The levels of DNA adducts arising from exposures influenced by variations in the doses, the frequency with which an individual is exposed, and rates of DNA repair for specific adducts. Each adduct has a characteristic efficiency with which it induces mutations. Based on experience with the well-studied DNA-reactive food carcinogen aflatoxin B 1 (AFB 1 ), a limit of 20 ppb or ∼30 μg/day has been set and is considered a tolerable daily intake (TDI). Since AFB 1 is considered a potent carcinogen, doses of 32 P-postlabeling or the use of surrogates such as hemoglobin adducts, together with approaches to evaluate the results. A discussion of approaches to estimating possible threshold effects for DNA-reactive carcinogens is made

Water reactive hydrogen fuel cell power system

Science.gov (United States)

Wallace, Andrew P; Melack, John M; Lefenfeld, Michael

2014-01-21

A water reactive hydrogen fueled power system includes devices and methods to combine reactant fuel materials and aqueous solutions to generate hydrogen. The generated hydrogen is converted in a fuel cell to provide electricity. The water reactive hydrogen fueled power system includes a fuel cell, a water feed tray, and a fuel cartridge to generate power for portable power electronics. The removable fuel cartridge is encompassed by the water feed tray and fuel cell. The water feed tray is refillable with water by a user. The water is then transferred from the water feed tray into a fuel cartridge to generate hydrogen for the fuel cell which then produces power for the user.

KSHV Rta promoter specification and viral reactivation

Directory of Open Access Journals (Sweden)

Jonathan eGuito

2012-02-01

Full Text Available Viruses are obligate intracellular pathogens whose biological success depends upon replication and packaging of viral genomes, and transmission of progeny viruses to new hosts. The biological success of herpesviruses is enhanced by their ability to reproduce their genomes without producing progeny viruses or killing the host cells, a process called latency. Latency permits a herpesvirus to remain undetected in its animal host for decades while maintaining the potential to reactivate, or switch, to a productive life cycle when host conditions are conducive to generating viral progeny. Direct interactions between many host and viral molecules are implicated in controlling herpesviral reactivation, suggesting complex biological networks that control the decision. One viral protein that is necessary and sufficient to switch latent KSHV into the lytic infection cycle is called K-Rta. Rta is a transcriptional activator that specifies promoters by binding direct DNA directly and interacting with cellular proteins. Among these cellular proteins, binding of K-Rta to RBP-Jk is essential for viral reactivation.. In contrast to the canonical model for Notch signaling, RBP-Jk is not uniformly and constitutively bound to the latent KSHV genome, but rather is recruited to DNA by interactions with K-Rta. Stimulation of RBP-Jk DNA binding requires high affinity binding of Rta to repetitive and palindromic CANT DNA repeats in promoters, and formation of ternary complexes with RBP-Jk. However, while K-Rta expression is necessary for initiating KSHV reactivation, K-Rta’s role as the switch is inefficient. Many factors modulate K-Rta’s function, suggesting that KSHV reactivation can be significantly regulated post-Rta expression and challenging the notion that herpesviral reactivation is bistable. This review analyzes rapidly evolving research on KSHV K-Rta to consider the role of K-Rta promoter specification in regulating the progression of KSHV reactivation.

Heterogeneous dermatitis complaints after change in drinking water treatment: a case report

Directory of Open Access Journals (Sweden)

Bhatia Rajiv

2006-06-01

Full Text Available Abstract Background The disinfectant monochloramine minimizes the formation of potentially hazardous and regulated byproducts, and many drinking water utilities are shifting to its use. Case presentation After a drinking water utility serving 2.4 million people switched to monochloramine for residual disinfection, a small number of residents complained of dermatitis reactions. We interviewed 17 people about their symptoms. Skin appearance, symptoms, and exposures were heterogeneous. Five respondents had history of hives or rash that preceded the switch to monochloramine. Conclusion The complaints described were heterogeneous, and many of the respondents had underlying or preexisting conditions that would offer plausible alternative explanations for their symptoms. We did not recommend further study of these complaints.

Evaluation of bituminized waste reactivity

International Nuclear Information System (INIS)

Camaro, S.; Moulinier, D.

2000-01-01

The bituminization process has been used for conditioning low and medium level (LML) radioactive waste, particularly to immobilize coprecipitation slurries and evaporation concentrates generated by effluent treatment. The process consists in mixing bitumen matrix with inactive soluble and slightly soluble salts added to insolubilize the radionuclides or resulting from the neutralization of acid effluents. This operation is performed at a sufficient temperature - depending on waste composition and bitumen grade to ensure the flow of the resulting mixture into metal containers. Exothermicity due to salts/salts or salts/bitumen reactions depending on the type of waste can be induced during or after the mixing step. This could produce an additional heat emission that the drum must be able to release to avoid a potentially incidental pattern with ignition risk, explaining why the CEA has been involved in evaluating the thermal reactivity of bituminized waste and its repercussions on the bituminization process. Given the difficulty of discriminating each exothermal reaction, the characterization of a global reactivity appears as a further precautionary measure, in addition to the definition of a working safety margin. The CEA has accordingly developed studies on this aspect. The article discusses the experimental methodology developed for the determination of the global reactivity. (authors)

Delta receptor antagonism, ethanol taste reactivity, and ethanol consumption in outbred male rats.

Science.gov (United States)

Higley, Amanda E; Kiefer, Stephen W

2006-11-01

Naltrexone, a nonspecific opioid antagonist, produces significant changes in ethanol responsivity in rats by rendering the taste of ethanol aversive as well as producing a decrease in voluntary ethanol consumption. The present study investigated the effect of naltrindole, a specific antagonist of delta opioid receptors, on ethanol taste reactivity and ethanol consumption in outbred rats. In the first experiment, rats received acute treatment of naltrexone, naltrindole, or saline followed by the measurement of ethanol consumption in a short-term access period. The second experiment involved the same treatments and investigated ethanol palatability (using the taste-reactivity test) as well as ethanol consumption. Results indicated that treatment with 3 mg/kg naltrexone significantly affected palatability (rendered ethanol more aversive, Experiment 2) and decreased voluntary ethanol consumption (Experiments 1 and 2). The effects of naltrindole were inconsistent. In Experiment 1, 8 mg/kg naltrindole significantly decreased voluntary ethanol consumption but this was not replicated in Experiment 2. The 8 mg/kg dose produced a significant increase in aversive responding (Experiment 2) but did not affect ingestive responding. Lower doses of naltrindole (2 and 4 mg/kg) were ineffective in altering rats' taste-reactivity response to and consumption of ethanol. While these data suggest that delta receptors are involved in rats' taste-reactivity response to ethanol and rats' ethanol consumption, it is likely that multiple opioid receptors mediate both behavioral responses.

Relation between coal rank, char reactivity, textural properties and NO emissions

Energy Technology Data Exchange (ETDEWEB)

Arenillas, A.; Rubiera, F.; Parra, J.B.; Pis, J.J. [Instituto Nacional del Carbon, Oviedo (Spain)

1999-07-01

A low volatile bituminous coal was pyrolysed at different heating rates to produce chars with different textural properties. There was a linear relationship between char reactivity and active surface area. The effect of coal rank on coal char textural properties was studied using a range of bituminous coals. The influence of textural properties and reactivity on NO emissions, and on the heterogeneous reduction of NO is discussed. 6 refs., 2 figs., 2 tabs.

Comparison of chlorine and chloramine in the release of mercury from dental amalgam.

Science.gov (United States)

Stone, Mark E; Scott, John W; Schultz, Stephen T; Berry, Denise L; Wilcoxon, Monte; Piwoni, Marv; Panno, Brent; Bordson, Gary

2009-01-01

The purpose of this project was to compare the ability of chlorine (HOCl/OCl(-)) and monochloramine (NH(2)Cl) to mobilize mercury from dental amalgam. Two types of amalgam were used in this investigation: laboratory-prepared amalgam and samples obtained from dental-unit wastewater. For disinfectant exposure simulations, 0.5 g of either the laboratory-generated or clinically obtained amalgam waste was added to 250 mL amber bottles. The amalgam samples were agitated by end-over-end rotation at 30 rpm in the presence of 1 mg/L chlorine, 10 mg/L chlorine, 1 mg/L monochloramine, 10 mg/L monochloramine, or deionized water for intervals of 0 h, 2 h, 4 h, 8 h, and 24 h for the clinically obtained amalgam waste samples and 4 h and 24 h for the laboratory-prepared samples. Chlorine and monochloramine concentrations were measured with a spectrophotometer. Samples were filtered through a 0.45 microm membrane filter and analyzed for mercury with USEPA standard method 245.7. When the two sample types were combined, the mean mercury level in the 1 mg/L chlorine group was 0.020 mg/L (n=25, SD=0.008). The 10 mg/L chlorine group had a mean mercury concentration of 0.59 mg/L (n=25, SD=1.06). The 1 mg/L chloramine group had a mean mercury level of 0.023 mg/L (n=25, SD=0.010). The 10 mg/L chloramine group had a mean mercury level of 0.024 mg/L (n=25, SD=0.011). Independent samples t-tests showed that there was a significant difference between the natural log mercury measurements of 10 mg/L chlorine compared to those of 1 mg/L and 10 mg/L chloramine. Changing from chlorine to chloramine disinfection at water treatment plants would not be expected to produce substantial increases in dissolved mercury levels in dental-unit wastewater.

Silkworm (Bombyx mori) hemocytes do not produce reactive oxygen metabolites as a part of defense mechanisms

Czech Academy of Sciences Publication Activity Database

Hyršl, P.; Číž, Milan; Kubala, Lukáš; Lojek, Antonín

2004-01-01

Roč. 49, č. 3 (2004), s. 315-319 ISSN 0015-5632 R&D Projects: GA AV ČR IBS5004009 Institutional research plan: CEZ:AV0Z5004920 Keywords : hemocytes * Bombyx mori * reactive oxygen species Subject RIV: BO - Biophysics Impact factor: 1.034, year: 2004

Reactive Kripke semantics

CERN Document Server

Gabbay, Dov M

2013-01-01

This text offers an extension to the traditional Kripke semantics for non-classical logics by adding the notion of reactivity. Reactive Kripke models change their accessibility relation as we progress in the evaluation process of formulas in the model. This feature makes the reactive Kripke semantics strictly stronger and more applicable than the traditional one. Here we investigate the properties and axiomatisations of this new and most effective semantics, and we offer a wide landscape of applications of the idea of reactivity. Applied topics include reactive automata, reactive grammars, rea

Melioidosis: reactivation during radiation therapy

International Nuclear Information System (INIS)

Jegasothy, B.V.; Goslen, J.B.; Salvatore, M.A.

1980-01-01

Melioidosis is caused by Pseudomonas pseudomallei, a gram-negative, motile bacillus which is a naturally occurring soil saprophyte. The organism is endemic in Southeast Asia, the Philippines, Australia, and parts of Central and South America. Most human disease occurs from infection acquired in these countries. Infection with P pseudomallei may produce no apparent clinical disease. Acute pneumonitis or septicemia may result from inhalation of the organism, and inoculation into sites of trauma may cause localized skin abscesses, or the disease may remain latent and be reactivated months or years later by trauma, burns, or pneumococcal pneumonia, diabetic ketoacidosis, influenza, or bronchogenic carcinoma. The last is probably the commonest form of melioidosis seen in the United States. We present the first case of reactivation of melioidosis after radiation therapy for carcinoma of the lung, again emphasizing the need to consider melioidosis in a septic patient with a history of travel, especially to Southeast Asia

Mechanisms of Kaposi's Sarcoma-Associated Herpesvirus Latency and Reactivation

Directory of Open Access Journals (Sweden)

Fengchun Ye

2011-01-01

Full Text Available The life cycle of Kaposi's sarcoma-associated herpesvirus (KSHV consists of latent and lytic replication phases. During latent infection, only a limited number of KSHV genes are expressed. However, this phase of replication is essential for persistent infection, evasion of host immune response, and induction of KSHV-related malignancies. KSHV reactivation from latency produces a wide range of viral products and infectious virions. The resulting de novo infection and viral lytic products modulate diverse cellular pathways and stromal microenvironment, which promote the development of Kaposi's sarcoma (KS. The mechanisms controlling KSHV latency and reactivation are complex, involving both viral and host factors, and are modulated by diverse environmental factors. Here, we review the cellular and molecular basis of KSHV latency and reactivation with a focus on the most recent advancements in the field.

Development of a reactivity worth correction scheme for the one-dimensional transient analysis

International Nuclear Information System (INIS)

Cho, J. Y.; Song, J. S.; Joo, H. G.; Kim, H. Y.; Kim, K. S.; Lee, C. C.; Zee, S. Q.

2003-11-01

This work is to develop a reactivity worth correction scheme for the MASTER one-dimensional (1-D) calculation model. The 1-D cross section variations according to the core state in the MASTER input file, which are produced for 1-D calculation performed by the MASTER code, are incorrect in most of all the core states except for exactly the same core state where the variations are produced. Therefore this scheme performs the reactivity worth correction factor calculations before the main 1-D transient calculation, and generates correction factors for boron worth, Doppler and moderator temperature coefficients, and control rod worth, respectively. These correction factors force the one dimensional calculation to generate the same reactivity worths with the 3-dimensional calculation. This scheme is applied to the control bank withdrawal accident of Yonggwang unit 1 cycle 14, and the performance is examined by comparing the 1-D results with the 3-D results. This problem is analyzed by the RETRAN-MASTER consolidated code system. Most of all results of 1-D calculation including the transient power behavior, the peak power and time are very similar with the 3-D results. In the MASTER neutronics computing time, the 1-D calculation including the correction factor calculation requires the negligible time comparing with the 3-D case. Therefore, the reactivity worth correction scheme is concluded to be very good in that it enables the 1-D calculation to produce the very accurate results in a few computing time

Reactivity and burnout of wood fuels

Energy Technology Data Exchange (ETDEWEB)

Dall' Ora, M.

2011-07-01

This thesis deals with the combustion of wood in pulverised fuel power plants. In this type of boiler, the slowest step in the wood conversion process is char combustion, which is one of the factors that not only determine the degree of fuel burnout, but also affect the heat release profile in the boiler and thereby the overall operation and efficiency of the plant. Chapter 1 consists of an introduction to thermal conversion of biomass fuels as well as a description of a Danish power plant where a measuring campaign was carried out as part of this project. Chapter 2 is a brief literature review of different aspects relevant to wood combustion, including wood structure and composition, wood pyrolysis, wood char properties and wood char oxidation. The full scale campaign, which is the subject of Chapter 3, included sampling of wood fuel before and after milling and sampling of gas and particles at the top of the combustion chamber. The collected samples and data are used to obtain an evaluation of the mills in operation at the power plant, the particle size distribution of the wood fuel, as well as the char conversion attained in the furnace. In Chapter 4 an experimental investigation on the relation between pyrolysis of wood in boiler-like conditions and wood char properties is presented. Chars from pine and beech wood were produced by fast pyrolysis in an entrained flow reactor and by slow pyrolysis in a thermogravimetric analyser. The influence of pyrolysis temperature, heating rate and particle size on char yield and morphology was investigated. The applied pyrolysis temperature varied in the range 673-1673 K for slow pyrolysis and 1073-1573 K for fast pyrolysis. The chars were oxidised in a thermogravimetric analyser and the mass loss data were used to determine char oxidation reactivity. Char yield from fast pyrolysis (104-105 K/s) was as low as 1-6% on a dry ash free basis, whereas it was about 15-17% for slow pyrolysis (10-20 K/min); char yield decreased as

Characterization of Transition Metal Carbide Layers Synthesized by Thermo-reactive Diffusion Processes

DEFF Research Database (Denmark)

Laursen, Mads Brink; Fernandes, Frederico Augusto Pires; Christiansen, Thomas Lundin

2015-01-01

. In this study halide-activated pack cementation techniques were used on tool steel Vanadis 6 and martensitic stainless steel AISI 420 in order to produce hard layers of titanium carbide (TiC), vanadium carbide (V8C7) and chromium carbides (Cr23C6 and Cr7C3). Surface layers were characterized by scanning......Hard wear resistant surface layers of transition metal carbides can be produced by thermo-reactive diffusion processes where interstitial elements from a steel substrate together with external sources of transition metals (Ti, V, Cr etc.) form hard carbide and/or nitride layers at the steel surface...... electron microscopy, X-ray diffraction and Vickers hardness testing. The study shows that porosityfree, homogenous and very hard surface layers can be produced by thermo-reactive diffusion processes. The carbon availability of the substrate influences thickness of obtained layers, as Vanadis 6 tool steel...

Digital reactivity meter

International Nuclear Information System (INIS)

Akkus, B.; Anac, H.; Alsan, S.; Erk, S.

1991-01-01

Nowadays, various digital methods making use of microcomputers for neutron detector signals and determining the reactivity by numerical calculations are used in reactor control systems in place of classical reactivity meters. In this work, a calculation based on the ''The Time Dependent Transport Equation'' has been developed for determining the reactivity numerically. The reactivity values have been obtained utilizing a computer-based data acquisition and control system and compared with the analog reactivity meter values as well as the values calculated from the ''Inhour Equation''

Evaluation of reactivity and Xe behavior during daily load following operation

International Nuclear Information System (INIS)

Sakamoto, Yasunori; Araki, Tsuneyasu; Yamamoto, Fumiaki

1992-01-01

A boiling water reactor (BWR) has an excellent load following capability provided by a core flow control, which is used for changing a reactor power level and for compensating the subsequent Xe concentration change. The core characteristics during load following operations are investigated in detail, using our reactor core simulator. Comparisons of changes of the Doppler reactivity, the void reactivity and the Xe reactivity during transients are performed. Also the features of Xe transient during load following operations are shown. It has been shown that the core flow change required to compensate the Xe reactivity change produces much greater change of the void reactivity than that required for power level changes, and that the resulting local power change in the lower part of the core is greater than that in the upper part, because the Xe concentration change in the lower part is hardly compensated by the core flow control. Also the effects of power level changes, cycle patterns, and initial concentration of Xe and I on the Xe transient behavior have been investigated. (author)

Feasibility of Batch Reactive Distillation with Equilibrium-Limited Consecutive Reactions in Rectifier, Stripper, or Middle-Vessel Column

Directory of Open Access Journals (Sweden)

T. Lukács

2011-01-01

Full Text Available A general overall feasibility methodology of batch reactive distillation of multireaction systems is developed to study all the possible configurations of batch reactive distillation. The general model equations are derived for multireaction system with any number of chemical equilibrium-limited reactions and for any number of components. The present methodology is demonstrated with the detailed study of the transesterification of dimethyl carbonate in two reversible cascade reactions in batch reactive distillation process. Pure methanol is produced as distillate, and pure diethyl carbonate is produced at the bottom simultaneously in middle-vessel column; in each section, continuous feeding of ethanol is necessary. The results of feasibility study are successfully validated by rigorous simulations.

Development of automated controller system for controlling reactivity by using FPGA in research reactor application

International Nuclear Information System (INIS)

Mohd Sabri Minhat; Izhar Abu Hussin; Mohd Idris Taib

2012-01-01

The scope for this research paper is to produce a detail design for Development of Automated Controller System for Controlling Reactivity by using FPGA in Research Reactor Application for high safety nuclear operation. The development of this project including design, purchasing, fabrication, installation, testing and validation and verification for one prototype automated controller system for controlling reactivity in industry local technology for human capacity and capability development towards the first Nuclear Power Programme (NPP) in Malaysia. The specific objectives of this research paper are to Development of Automated Controller System for Controlling Reactivity (ACSCR) in Research Reactor Application (PUSPATI TRIGA Reactor) by using simultaneous movement method; To design, fabricate and produce the accuracy of Control Rods Drive Mechanism to 0.1 mm resolution using a stepper motor as an actuator; To design, install and produce the system response to be more faster by using Field Programmable Gate Array (FPGA) and High Speed Computer; and to improve the Safety Level of the Research Reactor in high safety nuclear operation condition. (author)

Activation of iNKT Cells Prevents Salmonella-Enterocolitis and Salmonella-Induced Reactive Arthritis by Downregulating IL-17-Producing γδT Cells

Directory of Open Access Journals (Sweden)

Mariángeles Noto Llana

2017-09-01

Full Text Available Reactive arthritis (ReA is an inflammatory condition of the joints that arises following an infection. Salmonella enterocolitis is one of the most common infections leading to ReA. Although the pathogenesis remains unclear, it is known that IL-17 plays a pivotal role in the development of ReA. IL-17-producers cells are mainly Th17, iNKT, and γδT lymphocytes. It is known that iNKT cells regulate the development of Th17 lineage. Whether iNKT cells also regulate γδT lymphocytes differentiation is unknown. We found that iNKT cells play a protective role in ReA. BALB/c Jα18−/− mice suffered a severe Salmonella enterocolitis, a 3.5-fold increase in IL-17 expression and aggravated inflammation of the synovial membrane. On the other hand, activation of iNKT cells with α-GalCer abrogated IL-17 response to Salmonella enterocolitis and prevented intestinal and joint tissue damage. Moreover, the anti-inflammatory effect of α-GalCer was related to a drop in the proportion of IL-17-producing γδT lymphocytes (IL17-γδTcells rather than to a decrease in Th17 cells. In summary, we here show that iNKT cells play a protective role against Salmonella-enterocolitis and Salmonella-induced ReA by downregulating IL17-γδTcells.

Reactive adsorption: A cleaner technology in nuclear power plants

International Nuclear Information System (INIS)

Marton, G.; Szanya, T.; Hanak, L.

1996-01-01

Cleaner technology prefers work with minimal loss and the wastes cause the less environmental damages. In the spirit of the previous sentence in the present paper reactive adsorption is investigated for the removal of radioactive nuclides from nuclear power plant decontamination solutions. During alkaline, oxidative decontamination of nuclear power plant equipment a radioactive solution is produced. Owing to the storing difficulties of radioactive solutions it is necessary to develop a method for the in situ treatment of radioactive, alkaline, oxidative decontamination solutions, and for the concentration of radioactive components. Reactive adsorption seems to be promising for this purpose. 3 refs., 8 figs., 1 tab

C-Reactive Protein in Healthy Adult Nigerians | Baba | Nigerian ...

African Journals Online (AJOL)

Background: C-reactive protein (CRP) is an acute phase reactant produced in the liver in response to tissue injury or systemic inflammation, its release is stimulated by cytokines (interleukin-6 and tumour necrosis factor-alpha). Elevated CRP levels have been linked to an increased risk of later development of diabetes ...

The iodine reactivity; La reactivite de l'iode

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-07-01

The iodine is an important element because it has long life isotopes (such as iodine 129) and a great mobility in natural media. Iodine presents a complex chemistry because of its volatility and its strong redox reactivity. The S.E.C.R. works to better understand the reactivity of this element in different natural, industrial or biological environments. It plays a part in thermochemical sites as a possible way of hydrogen formation. This seminar gives some aspects relative to the chemical reactivity of iodine, since its thermochemistry in the I/S cycles to produce hydrogen to its reactivity in the natural medium and its potential radiological impact. This document includes 4 presentations transparencies dealing with: the {sup 129}I cycle rejected in the low radioactive gaseous and liquid effluents of the La Hague reprocessing plant (C. Frechou); a bibliographic review of iodine retention in soils (F. Bazer-Bachi); the hydrogen production and the iodine/sulfur thermochemical cycle (role of iodine in the process); and the direct characterization by electro-spray ionization mass spectroscopy of iodine fixation by fulvic acids (P. Reiller, B. Amekraz, C. Moulin, V. Moulin)

Structural Determinants of Alkyne Reactivity in Copper-Catalyzed Azide-Alkyne Cycloadditions

Directory of Open Access Journals (Sweden)

Xiaoguang Zhang

2016-12-01

Full Text Available This work represents our initial effort in identifying azide/alkyne pairs for optimal reactivity in copper-catalyzed azide-alkyne cycloaddition (CuAAC reactions. In previous works, we have identified chelating azides, in particular 2-picolyl azide, as “privileged” azide substrates with high CuAAC reactivity. In the current work, two types of alkynes are shown to undergo rapid CuAAC reactions under both copper(II- (via an induction period and copper(I-catalyzed conditions. The first type of the alkynes bears relatively acidic ethynyl C-H bonds, while the second type contains an N-(triazolylmethylpropargylic moiety that produces a self-accelerating effect. The rankings of reactivity under both copper(II- and copper(I-catalyzed conditions are provided. The observations on how other reaction parameters such as accelerating ligand, reducing agent, or identity of azide alter the relative reactivity of alkynes are described and, to the best of our ability, explained.

Cure Cycle Design Methodology for Fabricating Reactive Resin Matrix Fiber Reinforced Composites: A Protocol for Producing Void-free Quality Laminates

Science.gov (United States)

Hou, Tan-Hung

2014-01-01

For the fabrication of resin matrix fiber reinforced composite laminates, a workable cure cycle (i.e., temperature and pressure profiles as a function of processing time) is needed and is critical for achieving void-free laminate consolidation. Design of such a cure cycle is not trivial, especially when dealing with reactive matrix resins. An empirical "trial and error" approach has been used as common practice in the composite industry. Such an approach is not only costly, but also ineffective at establishing the optimal processing conditions for a specific resin/fiber composite system. In this report, a rational "processing science" based approach is established, and a universal cure cycle design protocol is proposed. Following this protocol, a workable and optimal cure cycle can be readily and rationally designed for most reactive resin systems in a cost effective way. This design protocol has been validated through experimental studies of several reactive polyimide composites for a wide spectrum of usage that has been documented in the previous publications.

Feasibility and parametric study of tetrahydrofuran dehydration using reactive distillation with low energy requirement

International Nuclear Information System (INIS)

Tavan, Yadollah

2014-01-01

A new configuration of a RD (reactive distillation) process is investigated to break the THF (tetrahydrofuran)/water azeotrope using Hysys process software. The main module is a column system containing the reaction of EO (ethylene oxide) with water, in which top and bottom streams are the desired products, THF and EG (ethylene glycol), respectively. This contribution explores feasibility of using the reaction in the RD column and also describes the influence of reflux ratio, reaction trays, operating pressure and feed–inlet locations of the RD column in simulation environment. The results show that high purities of EG and THF are simultaneously obtained by this novel technique leading to more profits of the RD process. The optimal design of the RD process is obtained by minimizing the energy demand and the optimum number of reactive trays is found to be 10. Furthermore, minimum energy demand is observed when the column operates at atmospheric pressure with reflux ratio of 1.25. Particularly, it is found that the optimal reboiler duty per unit THF produced is reduced from 32 to 3.7% for the new process as compared to the conventional one, while both schemes predict similar outputs. - Highlights: • A reactive distillation column is proposed to produce pure tetrahydrofuran. • The tetrahydrofuran-water azeotrope is broken using reactive distillation column. • High energy saving (88%) is found for the reactive distillation process

Effect of Ethyl Ester L-Lysine Triisocyanate addition to produce reactive PLA/PCL bio-polyester blends for biomedical applications.

Science.gov (United States)

Visco, Annamaria; Nocita, Davide; Giamporcaro, Alberto; Ronca, Sara; Forte, Giuseppe; Pistone, Alessandro; Espro, Claudia

2017-04-01

We report in this paper the effects of Ethyl Ester L-Lysine Triisocyanate (LTI) on the physical-mechanical properties of Poly(lactide)/Poly(ε-caprolactone) (PLA/PCL) polyesters blends. The PLA/PCL ratios considered were 20/80, 50/50 and 80/20 (wt/wt %) and LTI was added in amounts of 0.0-0.5-1.0 phr. PLA and PCL reacted with LTI during processing in a Brabender twin screw internal mixer to produce block copolymers in-situ. The resulting blends have been characterized by torque measurements, uniaxial tensile tests, Differential Scanning Calorimeter, contact angle measurements with a Phosphate Buffered Saline (PBS) solution, ATR analysis and morphological SEM observations. Experimental results highlighted how LTI enhanced interaction and dispersion of the two components, resulting into a synergic effect in mechanical properties. Mechanical and physical properties can be tailored by changing the blend composition. The most noticeable trend was an increase in ductility of the mixed polymers. Besides, LTI decreased blend's wet ability in PBS and lowered the starting of crystalline phase formation for both polymers, confirming an interaction among them. These reactive blends could find use as biomedical materials, e.g. absorbable suture threads or scaffolds for cellular growth. Copyright © 2017 Elsevier Ltd. All rights reserved.

Industrial scale salt-free reactive dyeing of cationized cotton fabric with different reactive dye chemistry.

Science.gov (United States)

Nallathambi, Arivithamani; Venkateshwarapuram Rengaswami, Giri Dev

2017-10-15

Dyeing of knitted cotton goods in the industry has been mostly with reactive dyes. Handling of salt laden coloured effluent arising out of dyeing process is one of the prime concerns of the industry. Cationization of cotton is one of the effective alternative to overcome the above problem. But for cationization to be successful at industrial scale it has to be carried out by exhaust process and should be adoptable for the various dye chemistries currently practiced in the industry. Hence, in the present work, industrial level exhaust method of cationization process was carried out with concentration of 40g/L and 80g/L. The fabrics were dyed with dyes of three different dye chemistry and assessed for its dyeing performance without the addition of salt. Dye shades ranging from medium to extra dark shades were produced without the addition of salt. This study will provide industries the recipe that can be adopted for cationized cotton fabric for the widely used reactive dyes at industrial level. Copyright © 2017 Elsevier Ltd. All rights reserved.

Simulation study of the production of biodiesel using feedstock mixtures of fatty acids in complex reactive distillation columns

International Nuclear Information System (INIS)

Cossio-Vargas, E.; Hernandez, S.; Segovia-Hernandez, J.G.; Cano-Rodriguez, M.I.

2011-01-01

Biodiesel can be produced from a number of natural, renewable sources, but vegetable oils are the main feedstocks. The current manufacturing biodiesel processes, however, have several disadvantages: expensive separation of products from the reaction mixture, and high costs due to relatively complex processes involving one to two reactors and several separation units. Therefore, to solve these problems, in recent years several researchers have developed a sustainable biodiesel production process based on reactive distillation. In this paper the production of biodiesel using feedstock mixtures of fatty acids is explored using reactive distillation sequences with thermal coupling. The results indicate that the complex reactive distillation sequences can produce a mixture of esters as bottoms product that can be used as biodiesel. In particular, the thermally coupled distillation sequence involving a side rectifier can handle the reaction and complete separation in accordance with process intensification principles. -- Highlights: ► Production of biodiesel using thermally coupled distillation sequences without reboilers. ► Esterification of fatty organic acids using reactive distillation. ► Carnot’s factor in reactive distillation.

Composition and reactivity of ash from sewage sludge

Energy Technology Data Exchange (ETDEWEB)

Willems, M; Pedersen, B; Jorgensen, S S

1976-01-01

Sewage sludge and sludge ash produced at 450 to 1050/sup 0/C in the laboratory or in a multiple hearth incinerator were analyzed by chemical and X-ray diffraction methods. Among the ash components were 23 to 32 percent calcium and magnesium phosphates and the following percentages of heavy metals: Zn 0.9, Cu 0.2, Pb 0.1, Cr 0.07, Ni 0.02, and Cd 0.006. As shown by EDTA-extraction, the reactivity of heavy metals was higher in ash produced at 450/sup 0/C than in dry sludge, but lower in ash produced above 800/sup 0/C. Phosphate in the 800 to 900/sup 0/C samples was dissolved in citric acid but not in citrate.

BN600 reactivity definition

International Nuclear Information System (INIS)

Zheltyshev, V.; Ivanov, A.

2000-01-01

Since 1980, the fast BN600 reactor with sodium coolant has been operated at Beloyarsk Nuclear Power Plant. The periodic monitoring of the reactivity modifications should be implemented in compliance with the standards and regulations applied in nuclear power engineering. The reactivity measurements are carried out in order to confirm the basic neutronic features of a BN600 reactor. The reactivity measurements are aimed to justify that nuclear safety is provided in course of the in-reactor installation of the experimental core components. Two reactivity meters are to be used on BN600 operation: 1. Digital on-line reactivity calculated under stationary reactor operation on power (approximation of the point-wise kinetics is applied). 2. Second reactivity meter used to define the reactor control rod operating components efficiency under reactor startup and take account of the changing efficiency of the sensor, however, this is more time-consumptive than the on-line reactivity meter. The application of two reactivity meters allows for the monitoring of the reactor reactivity under every operating mode. (authors)

Sequential SO{sub 2}/CO{sub 2} capture enhanced by steam reactivation of a CaO-based sorbent

Energy Technology Data Exchange (ETDEWEB)

Vasilije Manovic; Edward J. Anthony [CANMET Energy Technology Centre-Ottawa, Ottawa, ON (Canada). Natural Resources Canada

2008-07-15

The steam hydration reactivation characteristics of three limestone samples after multiple CO{sub 2} looping cycles are presented here. The CO{sub 2} cycles were performed in a tube furnace (TF) and the resulting samples were hydrated by steam in a pressure reactor (PR). The reactivation was performed with spent samples after carbonation and calcination stages. The reactivation tests were done with a saturated steam pressure at 200{sup o}C and also at atmospheric pressure and 100 {sup o}C. The characteristics of the reactivation samples were examined using BET and BJH pore characterization (for the original and spent samples, and samples reactivated under different conditions) and also by means of a thermogravimetric analyzer (TGA). The levels of hydration achieved by the reactivated samples were determined as well as the conversions during sulphation and multiple carbonation cycles. It was found that the presence of a CaCO{sub 3} layer strongly hinders sorbent hydration and adversely affects the properties of the reactivated sorbent with regard to its behavior in sulphation and multiple carbonation cycles. Here, hydration of calcined samples under pressure is the most effective method to produce superior sulphur sorbents. However, reactivation of calcined samples under atmospheric conditions also produces sorbents with significantly better properties in comparison to those of the original sorbents. These results show that separate CO{sub 2} capture and SO{sub 2} retention in fluidized bed systems enhanced by steam reactivation is promising even for atmospheric conditions if the material for hydration is taken from the calciner. 49 refs., 5 figs., 3 tabs.

Reactive distillation: an attractive alternative for the synthesis of unsaturated polyester

NARCIS (Netherlands)

Shah, M.R.; Zondervan, E.; Oudshoorn, M.L.; Haan, de A.B.

2011-01-01

Unsaturated polyester is traditionally produced in a batch wise operating reaction vessel connected to a distillation unit. An attractive alternative for the synthesis of unsaturated polyester is a reactive distillation. To value such alternative synthesis route reliable process models need to be

Effective neutron temperature measurements in well moderated reactor by the reactivity coefficient method

International Nuclear Information System (INIS)

Raisic, N.; Klinc, T.

1968-11-01

The ratio of the reactivity changes of a nuclear reactor produced by successive introduction of two different neutron absorbers in the reactor core, has been measured and information on effective neutron temperature at a particular point obtained. Boron was used as a l/v absorber and cadmium as an absorber sensiti ve to neutron temperature. Effective neutron temperature distribution has been deduced by moving absorbers across the reactor core and observing the corresponding reactivity changes. (author)

Cerebrovascular mental stress reactivity is impaired in hypertension

Directory of Open Access Journals (Sweden)

Naqvi Tasneem Z

2009-07-01

Full Text Available Abstract Background Brachial artery reactivity in response to shear stress is altered in subjects with hypertension. Since endothelial dysfunction is generalized, we hypothesized that carotid artery (CA reactivity would also be altered in hypertension. Purpose To compare (CA endothelium-dependent vasodilation in response to mental stress in normal and hypertensive subjects. Methods We evaluated CA reactivity to mental stress in 10 young healthy human volunteers (aged 23 ± 4 years, 20 older healthy volunteers (aged 49 ± 11 years and in 28 patients with essential hypertension (aged 51 ± 13 years. In 10 healthy volunteers and 12 hypertensive subjects, middle cerebral artery (MCA PW transcranial Doppler was performed before and 3 minutes after mental stress. Results Mental stress by Stroop color word conflict, math or anger recall tests caused CA vasodilation in young healthy subjects (0.61 ± 0.06 to 0.65 ± 0.07 cm, p Conclusion Mental stress produces CA vasodilation and is accompanied by an increase in CA and MCA blood flow in healthy subjects. This mental stress induced CA vasodilation and flow reserve is attenuated in subjects with hypertension and may reflect cerebral vascular endothelial dysfunction. Assessment of mental stress induced CA reactivity by ultrasound is a novel method for assessing the impact of hypertension on cerebrovascular endothelial function and blood flow reserve.

Method of controlling reactivity

International Nuclear Information System (INIS)

Tochihara, Hiroshi.

1982-01-01

Purpose: To improve the reactivity controlling characteristics by artificially controlling the leakage of neutron from a reactor and providing a controller for controlling the reactivity. Method: A reactor core is divided into several water gaps to increase the leakage of neutron, its reactivity is reduced, a gas-filled control rod or a fuel assembly is inserted into the gap as required, the entire core is coupled in a system to reduce the leakage of the neutron, and the reactivity is increased. The reactor shutdown is conducted by the conventional control rod, and to maintain critical state, boron density varying system is used together. Futher, a control rod drive is used with that similar to the conventional one, thereby enabling fast reactivity variation, and the positive reactivity can be obtained by the insertion, thereby improving the reactivity controlling characteristics. (Yoshihara, H.)

Reactive Arthritis

Directory of Open Access Journals (Sweden)

Eren Erken

2013-06-01

Full Text Available Reactive arthritis is an acute, sterile, non-suppurative and inflammatory arthropaty which has occured as a result of an infectious processes, mostly after gastrointestinal and genitourinary tract infections. Reiter syndrome is a frequent type of reactive arthritis. Both reactive arthritis and Reiter syndrome belong to the group of seronegative spondyloarthropathies, associated with HLA-B27 positivity and characterized by ongoing inflammation after an infectious episode. The classical triad of Reiter syndrome is defined as arthritis, conjuctivitis and urethritis and is seen only in one third of patients with Reiter syndrome. Recently, seronegative asymmetric arthritis and typical extraarticular involvement are thought to be adequate for the diagnosis. However, there is no established criteria for the diagnosis of reactive arthritis and the number of randomized and controlled studies about the therapy is not enough. [Archives Medical Review Journal 2013; 22(3.000: 283-299

Study of the controllable reactivity of aluminum alloys and their promising application for hydrogen generation

International Nuclear Information System (INIS)

Fan Meiqiang; Sun Lixian; Xu Fen

2010-01-01

The hydrolysis performances of two aluminum alloys are investigated as their reactivity can be controlled via the different additives. The additive of NaCl has the positive effect to improve the hydrolysis properties of the aluminum alloys with quicker hydrolysis kinetic and lower hydrolysis temperature. For examples, in 6 min of hydrolysis reaction, the Al-5 wt%Hg-5 wt%NaCl can produce 971 mL g -1 hydrogen, higher than 917 mL g -1 hydrogen from Al-10 wt%Hg alloy. The Al-In-NaCl alloy has lower hydrolysis temperature about 10 K than that of Al-In alloy. Meanwhile, the reactivity of Al alloys can be improved or reduced via the additive metals. It can be found that the additive cadmium can reduce the reactivity of Al-Hg alloy. The Al-Hg-Cd alloys can keep good stability at the moist atmosphere below 343 K and have excellent hydrolysis performance around 343-373 K. The debased reactivity of Al-Hg-Cd composite comes from the formation of CdHg 2 compounds in the milling process. But the additive Zn and Ga doped into the Al-In-NaCl alloys can quickly increase the reactivity of the alloy which can quickly react with water at room temperature and have high hydrogen yield up to the theoretic value. Therefore, it is a promising possibility that the controllable reactivity of aluminum alloys can be obtained through the different additive according to the practical request, and the Al alloys can produce pure hydrogen for the fuel cell via the hydrolysis reaction.

Lifetimes and reactivities of some 1,2-didehydroazepines commonly used in photoaffinity labeling experiments in aqueous solutions.

Science.gov (United States)

Rizk, Mary S; Shi, Xiaofeng; Platz, Matthew S

2006-01-17

The reactive 1,2-didehydroazepine (cyclic ketenimine) intermediates produced upon photolysis of phenyl azide, 3-hydroxyphenyl azide, 3-methoxyphenyl azide, and 3-nitrophenyl azide in water and in HEPES buffer were studied by laser flash photolysis techniques with UV-vis detection of the transient intermediates. The lifetimes of the 1,2-didehydroazepines were obtained along with the absolute rate constants of their reactions with typical amino acids, nucleosides, and other simple reagents present in a biochemical milieu. The nitro substituent greatly accelerates the bimolecular reactions of the cyclic ketenimines, and the 3-methoxy group greatly decelerates the absolute reactivity of 1,2-didehydroazepines. The intermediate produced by photolysis of 3-hydroxyphenyl azide is much more reactive than the intermediate produced by photolysis of 3-methoxyphenyl azide. We propose that the hydroxyl-substituted 1,2-didehydoazepines rapidly (ketenimines undergo hydrolysis. Azepinones react more rapidly with nucleophiles than do methoxy-substituted 1,2-didehydroazepines and are the active species present upon the photolysis of 3-hydroxyphenyl azide in aqueous solution.

Reactive Strength Index: A Poor Indicator of Reactive Strength?

Science.gov (United States)

Healy, Robin; Kenny, Ian; Harrison, Drew

2017-11-28

The primary aim was to assess the relationships between reactive strength measures and associated kinematic and kinetic performance variables achieved during drop jumps. A secondary aim was to highlight issues with the use of reactive strength measures as performance indicators. Twenty eight national and international level sprinters, consisting of fourteen men and women, participated in this cross-sectional analysis. Athletes performed drop jumps from a 0.3 m box onto a force platform with dependent variables contact time (CT), landing time (TLand), push-off time (TPush), flight time (FT), jump height (JH), reactive strength index (RSI, calculated as JH / CT), reactive strength ratio (RSR, calculated as FT / CT) and vertical leg spring stiffness (Kvert) recorded. Pearson's correlation test found very high to near perfect relationships between RSI and RSR (r = 0.91 to 0.97), with mixed relationships found between RSI, RSR and the key performance variables, (Men: r = -0.86 to -0.71 between RSI/RSR and CT, r = 0.80 to 0.92 between RSI/RSR and JH; Women: r = -0.85 to -0.56 between RSR and CT, r = 0.71 between RSI and JH). This study demonstrates that the method of assessing reactive strength (RSI versus RSR) may be influenced by the performance strategies adopted i.e. whether an athlete achieves their best reactive strength scores via low CTs, high JHs or a combination. Coaches are advised to limit the variability in performance strategies by implementing upper and / or lower CT thresholds to accurately compare performances between individuals.

Ultraviolet enhanced reactivation of a human virus: effect of delayed infection

International Nuclear Information System (INIS)

Bockstahler, L.E.; Lytle, C.D.; Stafford, J.E.; Haynes, K.F.

1976-01-01

The ability of UV-irradiated herpes simplex virus to form plaques was examined in monolayers of CV-1 monkey kidney cells preexposed to UV radiation at different intervals before virus assay. From analysis of UV reactivation (Weigle reactivation) curves it was found that as the interval between cell UV irradiation (0-20 J/m 2 ) and initiation of the virus assay was increased over a period of five days, (1) the capacity of the cells to support unirradiated virus plaque formation, which was decreased immediately following UV exposure of the monolayers, increased and returned to approximately normal levels within five days, and (2) at five days an exponential increase was observed in the relative plaque formation of irradiated virus as a function of UV dose to the monolayers. For high UV fluence (20 J/m 2 ) to the cells, the relative plaque formation by the UV-irradiated virus at five days was about 10-fold higher than that obtained from assay on unirradiated cells. This enhancement in plaque formation is interpreted as a delayed expression of Weigle reactivation. The amount of enhancement resulting from this delayed reactivation was several fold greater than that produced by the Weigle reactivation which occurred when irradiated herpes virus was assayed immediately following cell irradiation

Energy transfer in reactive and non-reactive H2 + OH collisions

International Nuclear Information System (INIS)

Rashed, O.; Brown, N.J.

1985-04-01

We have used the methods of quasi-classical dynamics to compute energy transfer properties of non-reactive and reactive H 2 + OH collisions. Energy transfer has been investigated as function of translational temperature, reagent rotational energy, and reagent vibrational energy. The energy transfer mechanism is complex with ten types of energy transfer possible, and evidence was found for all types. There is much more exchange between the translational degree of freedom and the H 2 vibrational degree of freedom than there is between translation and OH vibration. Translational energy is transferred to the rotational degrees of freedom of each molecule. There is a greater propensity for the transfer of translation to OH rotation than H 2 rotation. In reactive collisions, increases in reagent translational temperature predominantly appear as vibrational energy in the water molecule. Energy transfer in non-reactive and reactive collisions does not depend strongly on the initial angular momentum in either molecule. In non-reactive collisions, vibrational energy is transferred to translation, to the rotational degree of freedom of the same molecule, and to the rotational and vibrational degrees of freedom of the other molecule. In reactive collisions, the major effect of increasing the vibrational energy in reagent molecules is that, on the average, the vibrational energy of the reagents appears as product vibrational energy. 18 refs., 16 figs., 6 tabs

Evaluation of incremental reactivity and its uncertainty in Southern California.

Science.gov (United States)

Martien, Philip T; Harley, Robert A; Milford, Jana B; Russell, Armistead G

2003-04-15

The incremental reactivity (IR) and relative incremental reactivity (RIR) of carbon monoxide and 30 individual volatile organic compounds (VOC) were estimated for the South Coast Air Basin using two photochemical air quality models: a 3-D, grid-based model and a vertically resolved trajectory model. Both models include an extended version of the SAPRC99 chemical mechanism. For the 3-D modeling, the decoupled direct method (DDM-3D) was used to assess reactivities. The trajectory model was applied to estimate uncertainties in reactivities due to uncertainties in chemical rate parameters, deposition parameters, and emission rates using Monte Carlo analysis with Latin hypercube sampling. For most VOC, RIRs were found to be consistent in rankings with those produced by Carter using a box model. However, 3-D simulations show that coastal regions, upwind of most of the emissions, have comparatively low IR but higher RIR than predicted by box models for C4-C5 alkenes and carbonyls that initiate the production of HOx radicals. Biogenic VOC emissions were found to have a lower RIR than predicted by box model estimates, because emissions of these VOC were mostly downwind of the areas of primary ozone production. Uncertainties in RIR of individual VOC were found to be dominated by uncertainties in the rate parameters of their primary oxidation reactions. The coefficient of variation (COV) of most RIR values ranged from 20% to 30%, whereas the COV of absolute incremental reactivity ranged from about 30% to 40%. In general, uncertainty and variability both decreased when relative rather than absolute reactivity metrics were used.

PET CT Identifies Reactivation Risk in Cynomolgus Macaques with Latent M. tuberculosis.

Directory of Open Access Journals (Sweden)

Philana Ling Lin

2016-07-01

Full Text Available Mycobacterium tuberculosis infection presents across a spectrum in humans, from latent infection to active tuberculosis. Among those with latent tuberculosis, it is now recognized that there is also a spectrum of infection and this likely contributes to the variable risk of reactivation tuberculosis. Here, functional imaging with 18F-fluorodeoxygluose positron emission tomography and computed tomography (PET CT of cynomolgus macaques with latent M. tuberculosis infection was used to characterize the features of reactivation after tumor necrosis factor (TNF neutralization and determine which imaging characteristics before TNF neutralization distinguish reactivation risk. PET CT was performed on latently infected macaques (n = 26 before and during the course of TNF neutralization and a separate set of latently infected controls (n = 25. Reactivation occurred in 50% of the latently infected animals receiving TNF neutralizing antibody defined as development of at least one new granuloma in adjacent or distant locations including extrapulmonary sites. Increased lung inflammation measured by PET and the presence of extrapulmonary involvement before TNF neutralization predicted reactivation with 92% sensitivity and specificity. To define the biologic features associated with risk of reactivation, we used these PET CT parameters to identify latently infected animals at high risk for reactivation. High risk animals had higher cumulative lung bacterial burden and higher maximum lesional bacterial burdens, and more T cells producing IL-2, IL-10 and IL-17 in lung granulomas as compared to low risk macaques. In total, these data support that risk of reactivation is associated with lung inflammation and higher bacterial burden in macaques with latent Mtb infection.

Reactive thymic hyperplasia following treatment of ACTH-producing tumors

International Nuclear Information System (INIS)

Schmidt, S.; Klose, K.J.; Iwinska-Zelder, J.; Frank, M.; Ehlenz, K.; Kisker, O.

1997-01-01

Surgical or conservative treatment of ACTH-producing tumors results in acute drop of the previously excessively high cortisol levels. The following associated pathophysiological changes also occur in the organism's recovery from stress, such as trauma, operation or chemotherapy of tumors. Both cases result in a regeneration of the immune system, which might even be exalted. The corresponding radiographic feature is the 'rebound' enlargement of the thymus occuring about six months after remission of hypercortisolism. Histological examination reveals benign thymus hyperplasia. Especially in cases of still unkown primary tumor the apperance of this anterior mediastinal mass can lead to misdiagnosis. We present the cases of two patients with diffuse thymic hyperplasia following surgical and medical correction of hypercortisolism. One patient suffered from classic Cushing's disease responding to transsphenoidal resection of an ACTH-secreting pituitary microadenoma. Six monsths later CT of the chest incidentally demonstrated an anterior mediastinal mass known as thymic hyperplasia. The second patient presented with an ectopic, still unknown source of ACTH-production. (orig./AJ) [de

Fabrication of conductive copper patterns using reactive inkjet printing followed by two-step electroless plating

International Nuclear Information System (INIS)

Chen, Jin-Ju; Lin, Guo-Qiang; Wang, Yan; Sowade, Enrico; Baumann, Reinhard R.; Feng, Zhe-Sheng

2017-01-01

Highlights: • Copper patterns were fabricated by reactive inkjet printing and two-step electroless plating. • Cu particles produced via reactive inkjet printing act as catalyst for copper electroless plating. • High conductivity can be obtained without many printing passes and high temperature sintering. • This approach can largely avoid nozzle-clogging problems. • This approach presents a potential way in the flexible printed electronics with simple process. - Abstract: A simple and low-cost process for fabricating conductive copper patterns on flexible polyimide substrates was demonstrated. Copper catalyst patterns were first produced on polyimide substrates using reactive inkjet printing of Cu (II)-bearing ink and reducing ink, and then the conductive copper patterns were generated after a two-step electroless plating procedure. The copper layers were characterized by optical microscope, SEM, XRD and EDS. Homogeneously distributed copper nanoclusters were found in the catalyst patterns. A thin copper layer with uniform particle size was formed after first-step electroless plating, and a thick copper layer of about 14.3 μm with closely packed structure and fine crystallinity was produced after second-step electroless plating. This resulting copper layer had good solderability, reliable adhesion strength and a low resistivity of 5.68 μΩ cm without any sintering process.

Fabrication of conductive copper patterns using reactive inkjet printing followed by two-step electroless plating

Energy Technology Data Exchange (ETDEWEB)

Chen, Jin-Ju; Lin, Guo-Qiang; Wang, Yan [State Key Laboratory of Electronic Thin Films and Integrated Devices, University of Electronic Science and Technology of China, Chengdu, 610054 (China); Sowade, Enrico; Baumann, Reinhard R. [Digital Printing and Imaging Technology, Technische Universität Chemnitz, Chemnitz, 09126 (Germany); Feng, Zhe-Sheng, E-mail: fzs@uestc.edu.cn [State Key Laboratory of Electronic Thin Films and Integrated Devices, University of Electronic Science and Technology of China, Chengdu, 610054 (China)

2017-02-28

Highlights: • Copper patterns were fabricated by reactive inkjet printing and two-step electroless plating. • Cu particles produced via reactive inkjet printing act as catalyst for copper electroless plating. • High conductivity can be obtained without many printing passes and high temperature sintering. • This approach can largely avoid nozzle-clogging problems. • This approach presents a potential way in the flexible printed electronics with simple process. - Abstract: A simple and low-cost process for fabricating conductive copper patterns on flexible polyimide substrates was demonstrated. Copper catalyst patterns were first produced on polyimide substrates using reactive inkjet printing of Cu (II)-bearing ink and reducing ink, and then the conductive copper patterns were generated after a two-step electroless plating procedure. The copper layers were characterized by optical microscope, SEM, XRD and EDS. Homogeneously distributed copper nanoclusters were found in the catalyst patterns. A thin copper layer with uniform particle size was formed after first-step electroless plating, and a thick copper layer of about 14.3 μm with closely packed structure and fine crystallinity was produced after second-step electroless plating. This resulting copper layer had good solderability, reliable adhesion strength and a low resistivity of 5.68 μΩ cm without any sintering process.

Insights into the reactivation of cobalamin-dependent methionine synthase

Energy Technology Data Exchange (ETDEWEB)

Koutmos, Markos; Datta, Supratim; Pattridge, Katherine A.; Smith, Janet L.; Matthews, Rowena G.; (Michigan)

2009-12-10

Cobalamin-dependent methionine synthase (MetH) is a modular protein that catalyzes the transfer of a methyl group from methyltetrahydrofolate to homocysteine to produce methionine and tetrahydrofolate. The cobalamin cofactor, which serves as both acceptor and donor of the methyl group, is oxidized once every {approx}2,000 catalytic cycles and must be reactivated by the uptake of an electron from reduced flavodoxin and a methyl group from S-adenosyl-L-methionine (AdoMet). Previous structures of a C-terminal fragment of MetH (MetH{sup CT}) revealed a reactivation conformation that juxtaposes the cobalamin- and AdoMet-binding domains. Here we describe 2 structures of a disulfide stabilized MetH{sup CT} ({sub s-s}MetH{sup CT}) that offer further insight into the reactivation of MetH. The structure of {sub s-s}MetH{sup CT} with cob(II)alamin and S-adenosyl-L-homocysteine represents the enzyme in the reactivation step preceding electron transfer from flavodoxin. The structure supports earlier suggestions that the enzyme acts to lower the reduction potential of the Co(II)/Co(I) couple by elongating the bond between the cobalt and its upper axial water ligand, effectively making the cobalt 4-coordinate, and illuminates the role of Tyr-1139 in the stabilization of this 4-coordinate state. The structure of {sub s-s}MetH{sub CT} with aquocobalamin may represent a transient state at the end of reactivation as the newly remethylated 5-coordinate methylcobalamin returns to the 6-coordinate state, triggering the rearrangement to a catalytic conformation.

Sub-chronic lead exposure produces β1-adrenoceptor downregulation decreasing arterial pressure reactivity in rats.

Science.gov (United States)

Toscano, Cindy Medici; Simões, Maylla Ronacher; Alonso, Maria Jesus; Salaices, Mercedes; Vassallo, Dalton Valentim; Fioresi, Mirian

2017-07-01

Lead is considered a causative factor for hypertension and other cardiovascular diseases. To investigate the effects of sub-chronic lead exposure on blood pressure reactivity and cardiac β 1 -adrenoceptor activity and to evaluate whether the effects found in vitro are similar to those found in vivo. Male Wistar rats were randomly distributed into two groups: control rats (Ct) and rats administered drinking water containing 100ppm lead (Pb) for 30days. Blood pressure in the Pb rats increased starting from the first week of treatment until the end of the study [systolic blood pressure, Ct: 122±4 vs. Pb: 143±3mmHg; diastolic blood pressure, Ct: 63±4 vs. Pb: 84±4mmHg]. The heart rate was also increased (Ct: 299±11 vs. Pb: 365±11bpm), but the pressure reactivity to phenylephrine was decreased. Losartan and hexamethonium exhibited a greater reduction in blood pressure of Pb rats than in the Ct rats. Isoproterenol increased the left ventricular systolic and end-diastolic pressure, and heart rate only in Ct rats, suggesting that lead induced β 1 -adrenoceptor downregulation. Indomethacin reduced the blood pressure and heart rate in the Pb rats, suggesting the involvement of cyclooxygenase-derived products (which are associated with reduced nitric oxide bioavailability) in this process. These findings offer further evidence that the effects of sub-chronic lead exposure in vitro can be reproduced in vivo-even at low concentrations-thus triggering mechanisms for the development of hypertension. Therefore, lead should be considered an environmental risk factor for cardiovascular disease. Copyright © 2017 Elsevier Inc. All rights reserved.

Reactivity and reactions to regulatory transparency in medicine, psychotherapy and counselling.

Science.gov (United States)

McGivern, Gerry; Fischer, Michael D

2012-02-01

We explore how doctors, psychotherapists and counsellors in the U.K. react to regulatory transparency, drawing on qualitative research involving 51 semi-structured interviews conducted during 2008-10. We use the concept of 'reactivity mechanisms' (Espeland & Sauder, 2007) to explain how regulatory transparency disrupts practices through simplifying and decontextualizing them, altering practitioners' reflexivity, leading to defensive forms of practice. We make an empirical contribution by exploring the impact of transparency on doctors compared with psychotherapists and counsellors, who represent an extreme case due to their uniquely complex practice, which is particularly affected by this form of regulation. We make a contribution to knowledge by developing a model of reactivity mechanisms, which explains how clinical professionals make sense of media and professional narratives about regulation in ways that produce emotional reactions and, in turn, defensive reactivity to transparency. Copyright © 2011 Elsevier Ltd. All rights reserved.

Reactivity on the Web

OpenAIRE

Bailey, James; Bry, François; Eckert, Michael; Patrânjan, Paula Lavinia

2005-01-01

Reactivity, the ability to detect simple and composite events and respond in a timely manner, is an essential requirement in many present-day information systems. With the emergence of new, dynamic Web applications, reactivity on the Web is receiving increasing attention. Reactive Web-based systems need to detect and react not only to simple events but also to complex, real-life situations. This paper introduces XChange, a language for programming reactive behaviour on the Web,...

Epstein-Barr Virus Lytic Reactivation Activates B Cells Polyclonally and Induces Activation-Induced Cytidine Deaminase Expression: A Mechanism Underlying Autoimmunity and Its Contribution to Graves' Disease.

Science.gov (United States)

Nagata, Keiko; Kumata, Keisuke; Nakayama, Yuji; Satoh, Yukio; Sugihara, Hirotsugu; Hara, Sayuri; Matsushita, Michiko; Kuwamoto, Satoshi; Kato, Masako; Murakami, Ichiro; Hayashi, Kazuhiko

2017-04-01

Graves' disease is an autoimmune disease that results in and is the most common cause of hyperthyroidism, and the reactivation of persisting Epstein-Barr virus (EBV) in B lymphocytes induces the differentiation of host B cells into plasma cells. We previously reported that some EBV-infected B cells had thyrotropin receptor antibodies (TRAbs) as surface immunoglobulins (Igs), and EBV reactivation induced these TRAb+EBV+ cells to produce TRAbs. EBV reactivation induces Ig production from host B cells. The purpose of the present study was to examine total Ig productions from B cell culture fluids and to detect activation-induced cytidine deaminase (AID), nuclear factor kappa B (NF-κB), and EBV latent membrane protein (LMP) 1 in culture B cells during EBV reactivation induction and then we discussed the mechanisms of EBV reactivation-induced Ig production in relation to autoimmunity. We showed that the EBV reactivation induces the production of every isotype of Ig and suggested that the Ig production was catalyzed by AID through LMP1 and NF-κB. The results that the amount of IgM was significantly larger compared with IgG suggested the polyclonal B cell activation due to LMP1. We proposed the pathway of EBV reactivation induced Ig production; B cells newly infected with EBV are activated by polyclonal B cell activation and produce Igs through plasma cell differentiation induced by EBV reactivation. LMP1-induced AID enabled B cells to undergo class-switch recombination to produce every isotype of Ig. According to this mechanism, EBV rescues autoreactive B cells to produce autoantibodies, which contribute to the development and exacerbation of autoimmune diseases.

Electron transfer reactivity of the Arabidopsis thaliana sulfhydryl oxidase AtErv1

DEFF Research Database (Denmark)

Farver, Ole; Vitu, Elvira; Wherland, Scot

2009-01-01

The redox reactivity of the three disulfide bridges and the flavin present in each protomer of the wild-type Arabidopsis thaliana mitochondrial sulfhydryl oxidase (AtErv1) homodimer has been investigated. Pulse radiolytically produced CO2- radical ions were found to reduce the disulfide bridges...

Computational simulation of reactive species production by methane-air DBD at high pressure and high temperature

Science.gov (United States)

Takana, H.; Tanaka, Y.; Nishiyama, H.

2012-01-01

Computational simulations of a single streamer in DBD in lean methane-air mixture at pressure of 1 and 3 atm and temperature of 300 and 500 K were conducted for plasma-enhanced chemical reactions in a closed system. The effects of surrounding pressure and temperature are characterized for reactive species production by a DBD discharge. The results show that the production characteristics of reactive species are strongly influenced by the total gas number density and the higher concentration of reactive species are produced at higher pressure and lower gas temperature for a given initial reduced electric field.

Digital reactivity meter

International Nuclear Information System (INIS)

Jiang Zongbing

1996-02-01

The importance and the usual methods of reactivity measurement in a nuclear reactor are presented. Emphasis is put upon the calculation principle, software and hardware components, main specifications, application, as well as the features of the digital reactivity meter. The test results of operation in various reactors shown that the meter possess the following features: high accuracy, short response time, low output noise, high resolution, wide measuring range, simple and flexible to operate, high stability and reliability. In addition, the reactivity meter can save the measuring data automatically and have a perfect capability of self-verifying. It not only meet the requirement of the reactivity measurement in nuclear power plant, but also can be applied to various types of reactors. (1 tab.)

Monadic Functional Reactive Programming

NARCIS (Netherlands)

A.J. van der Ploeg (Atze); C Shan

2013-01-01

htmlabstractFunctional Reactive Programming (FRP) is a way to program reactive systems in functional style, eliminating many of the problems that arise from imperative techniques. In this paper, we present an alternative FRP formulation that is based on the notion of a reactive computation: a

Reactivity costs in MARIA reactor

International Nuclear Information System (INIS)

Marcinkowska, Zuzanna E.; Pytel, Krzysztof M.; Frydrysiak, Andrzej

2017-01-01

Highlights: • The methodology for calculating consumed fuel cost of excess reactivity is proposed. • Correlation between time integral of the core excess reactivity and released energy. • Reactivity price gives number of fuel elements required for given excess reactivity. - Abstract: For the reactor operation at high power level and carrying out experiments and irradiations the major cost of reactor operation is the expense of nuclear fuel. In this paper the methodology for calculating consumed fuel cost-relatedness of excess reactivity is proposed. Reactivity costs have been determined on the basis of operating data. A number of examples of calculating the reactivity costs for processes such as: strong absorbing material irradiation, molybdenium-99 production, beryllium matrix poisoning and increased moderator temperature illustrates proposed method.

Reactive perforating collagenosis

Directory of Open Access Journals (Sweden)

Yadav Mukesh

2009-01-01

Full Text Available Reactive perforating collagenosis is a rare cutaneous disorder of unknown etiology. We hereby describe a case of acquired reactive perforating collagenosis in a patient of diabetes and chronic renal failure.

Water Susceptibility and Mechanical Properties of Thermoplastic Starch–Pectin Blends Reactively Extruded with Edible Citric Acid

OpenAIRE

Da Róz,Alessandra Luzia; Veiga-Santos,Pricila; Ferreira,Adriane Medeiros; Antunes,Thaís Cristina Ribeiro; Leite,Fabio de Lima; Yamaji,Fabio Minoru; Carvalho,Antonio José Felix de

2016-01-01

Pectin and starch are edible, non-toxic, biodegradable and obtained from renewable sources. Also, have the benefit to be easily cross-linked producing hydrogels. Reactive extrusion with edible citric acid and cross linking interactions was evaluated on extruded thermoplastic in natura and cationic starch-pectin blends. Materials water susceptibility and mechanical properties were characterised. Reactive extrusion decreased (up to 75% in natura starch) mechanical properties. Also have decrease...

Two generators to produce SI-traceable reference gas mixtures for reactive compounds at atmospheric levels

Science.gov (United States)

Pascale, C.; Guillevic, M.; Ackermann, A.; Leuenberger, D.; Niederhauser, B.

2017-12-01

To answer the needs of air quality and climate monitoring networks, two new gas generators were developed and manufactured at METAS in order to dynamically generate SI-traceable reference gas mixtures for reactive compounds at atmospheric concentrations. The technical features of the transportable generators allow for the realization of such gas standards for reactive compounds (e.g. NO2, volatile organic compounds) in the nmol · mol-1 range (ReGaS2), and fluorinated gases in the pmol ṡ mol-1 range (ReGaS3). The generation method is based on permeation and dynamic dilution. The transportable generators have multiple individual permeation chambers allowing for the generation of mixtures containing up to five different compounds. This mixture is then diluted using mass flow controllers, thus making the production process adaptable to generate the required amount of substance fraction. All parts of ReGaS2 in contact with the gas mixture are coated to reduce adsorption/desorption processes. Each input parameter required to calculate the generated amount of substance fraction is calibrated with SI-primary standards. The stability and reproducibility of the generated amount of substance fractions were tested with NO2 for ReGaS2 and HFC-125 for ReGaS3. They demonstrate stability over 1-4 d better than 0.4% and 0.8%, respectively, and reproducibility better than 0.7% and 1%, respectively. Finally, the relative expanded uncertainty of the generated amount of substance fraction is smaller than 3% with the major contributions coming from the uncertainty of the permeation rate and/or of the purity of the matrix gas. These relative expanded uncertainties meet then the needs of the data quality objectives fixed by the World Meteorological Organization.

What makes ecological systems reactive?

Science.gov (United States)

Snyder, Robin E

2010-06-01

Although perturbations from a stable equilibrium must ultimately vanish, they can grow initially, and the maximum initial growth rate is called reactivity. Reactivity thus identifies systems that may undergo transient population surges or drops in response to perturbations; however, we lack biological and mathematical intuition about what makes a system reactive. This paper presents upper and lower bounds on reactivity for an arbitrary linearized model, explores their strictness, and discusses their biological implications. I find that less stable systems (i.e. systems with long transients) have a smaller possible range of reactivities for which no perturbations grow. Systems with more species have a higher capacity to be reactive, assuming species interactions do not weaken too rapidly as the number of species increases. Finally, I find that in discrete time, reactivity is determined largely by mean interaction strength and neither discrete nor continuous time reactivity are sensitive to food web topology. 2010 Elsevier Inc. All rights reserved.

The Influence of Sintering Temperature of Reactive Sintered (Ti, MoC-Ni Cermets

Directory of Open Access Journals (Sweden)

Marek Jõeleht

2015-09-01

Full Text Available Titanium-molybdenum carbide nickel cermets ((Ti, MoC-Ni were produced using high energy milling and reactive sintering process. Compared to conventional TiC-NiMo cermet sintering the parameters for reactive sintered cermets vary since additional processes are present such as carbide synthesis. Therefore, it is essential to acquire information about the suitable sintering regime for reactive sintered cermets. One of the key parameters is the final sintering temperature when the liquid binder Ni forms the final matrix and vacancies inside the material are removed. The influence of the final sintering temperature is analyzed by scanning electron microscopy. Mechanical properties of the material are characterized by transverse rupture strength, hardness and fracture toughness.DOI: http://dx.doi.org/10.5755/j01.ms.21.3.7179

Switchable narrow band reflectors produced in a single curing step

NARCIS (Netherlands)

2006-01-01

A method to produce a multiphase polymer-based film by polymg. monomer in the presence of a non-reactive liq. crystal and a dichroic photoinitiator whereby the polymn. is initiated by the use of linearly polarized light, the initial mixt. being cholesteric before polymn. is described. A multiphase

Kinematics of self-initiated and reactive karate punches.

Science.gov (United States)

Martinez de Quel, Oscar; Bennett, Simon J

2014-03-01

This study investigated whether within-task expertise affects the reported asymmetry in execution time exhibited in reactive and self-initiated movements. Karate practitioners and no-karate practitioners were compared performing a reverse punch in reaction to an external stimulus or following the intention to produce a response (self-initiated). The task was completed following the presentation of a specific (i.e., life-size image of opponent) or general stimulus and in the presence of click trains or white noise. Kinematic analyses indicated reactive movement had shorter time to peak velocity and movement time, as well as greater accuracy than self-initiated movement. These differences were independent of participant skill level although peak velocity was higher in the karate practice group than in the no-karate practice group. Reaction time (RT) of skilled participants was facilitated by a specific stimulus. There was no effect on RT or kinematic variables of the different type of auditory cues. The results of this study indicate that asymmetry in execution time of reactive and self-initiated movement holds irrespective of within-task expertise and stimulus specificity. This could have implications for training of sports and/or relearning of tasks that require rapid and accurate movements to intercept/contact a target.

Myelin-specific T cells induce interleukin-1beta expression in lesion-reactive microglial-like cells in zones of axonal degeneration

DEFF Research Database (Denmark)

Grebing, Manuela; Nielsen, Helle H; Fenger, Christina D

2016-01-01

lesion-reactive CD11b(+) ramified microglia. These results suggest that myelin-specific T cells stimulate lesion-reactive microglial-like cells to produce IL-1β. These findings are relevant to understand the consequences of T-cell infiltration in white and gray matter lesions in patients with MS. GLIA...

Multimodal assessment of emotional reactivity in borderline personality pathology: the moderating role of posttraumatic stress disorder symptoms.

Science.gov (United States)

Dixon-Gordon, Katherine L; Gratz, Kim L; Tull, Matthew T

2013-08-01

Emotional reactivity has been theorized to play a central role in borderline personality (BP) pathology. Although growing research provides evidence for subjective emotional reactivity in BP pathology, research on physiological or biological reactivity among people with BP pathology is less conclusive. With regard to biological reactivity in particular, research on cortisol reactivity (a neurobiological marker of emotional reactivity) in response to stressors among individuals with BP pathology has produced contradictory results and highlighted the potential moderating role of PTSD-related pathology. Thus, this study sought to examine the moderating role of PTSD symptoms in the relation between BP pathology and both subjective (self-report) and biological (cortisol) emotional reactivity to a laboratory stressor. Participants were 171 patients in a residential substance use disorder treatment center. Consistent with hypotheses, results revealed a significant main effect of BP pathology on subjective emotional reactivity to the laboratory stressor. Furthermore, results revealed a significant interaction between BP pathology and PTSD symptoms in the prediction of cortisol reactivity, such that BP pathology was associated with heightened cortisol reactivity only among participants with low levels of PTSD symptoms. Similar findings were obtained when examining the interaction between BP pathology and the reexperiencing and avoidance/numbing symptoms of PTSD specifically. Results highlight the moderating role of PTSD symptoms in the BP-reactivity relation. Copyright © 2013 Elsevier Inc. All rights reserved.

Digital reactivity meter

International Nuclear Information System (INIS)

Copie, M.; Valantic, B.

1978-01-01

Digital reactivity meters (DRM) are mostly used as measuring instruments, e.g. for calibration of control rods, and there are only a few cases of their incorporation into the control systems of the reactors. To move in this direction there is more development work needed. First of all, fast algorithms are needed for inverse kinetics equations to relieve the computer for more important tasks of reactor model solving in real time. The next problem, currently under investigation, is the incorporation of the reactor thermal-hydraulic model into the DRM so that it can be used in the power range. Such an extension of DHM allows presentation not only of the instantaneous reactivity of the system, but also the inserted reactivity can be estimated from the temperature reactivity feed-backs. One of the applications of this concept is the anomalous digital reactivity monitor (ADRN) as part of the reactor protection system. As a solution of the first problem, a fast algorithm for solving the inverse kinetics equations has been implemented in the off-line program RODCAL on CDC 1700 computer and tested for its accuracy by performing different control rod calibrations on the reactor TRIGA

Hydroxyl radical reactivity at the air-ice interface

Directory of Open Access Journals (Sweden)

T. F. Kahan

2010-01-01

Full Text Available Hydroxyl radicals are important oxidants in the atmosphere and in natural waters. They are also expected to be important in snow and ice, but their reactivity has not been widely studied in frozen aqueous solution. We have developed a spectroscopic probe to monitor the formation and reactions of hydroxyl radicals in situ. Hydroxyl radicals are produced in aqueous solution via the photolysis of nitrite, nitrate, and hydrogen peroxide, and react rapidly with benzene to form phenol. Similar phenol formation rates were observed in aqueous solution and bulk ice. However, no reaction was observed at air-ice interfaces, or when bulk ice samples were crushed prior to photolysis to increase their surface area. We also monitored the heterogeneous reaction between benzene present at air-water and air-ice interfaces with gas-phase OH produced from HONO photolysis. Rapid phenol formation was observed on water surfaces, but no reaction was observed at the surface of ice. Under the same conditions, we observed rapid loss of the polycyclic aromatic hydrocarbon (PAH anthracene at air-water interfaces, but no loss was observed at air-ice interfaces. Our results suggest that the reactivity of hydroxyl radicals toward aromatic organics is similar in bulk ice samples and in aqueous solution, but is significantly suppressed in the quasi-liquid layer (QLL that exists at air-ice interfaces.

Oxidation of trichloroethylene, toluene, and ethanol vapors by a partially saturated permeable reactive barrier

Science.gov (United States)

Mahmoodlu, Mojtaba G.; Hassanizadeh, S. Majid; Hartog, Niels; Raoof, Amir

2014-08-01

The mitigation of volatile organic compound (VOC) vapors in the unsaturated zone largely relies on the active removal of vapor by ventilation. In this study we considered an alternative method involving the use of solid potassium permanganate to create a horizontal permeable reactive barrier for oxidizing VOC vapors. Column experiments were carried out to investigate the oxidation of trichloroethylene (TCE), toluene, and ethanol vapors using a partially saturated mixture of potassium permanganate and sand grains. Results showed a significant removal of VOC vapors due to the oxidation. We found that water saturation has a major effect on the removal capacity of the permeable reactive layer. We observed a high removal efficiency and reactivity of potassium permanganate for all target compounds at the highest water saturation (Sw = 0.6). A change in pH within the reactive layer reduced oxidation rate of VOCs. The use of carbonate minerals increased the reactivity of potassium permanganate during the oxidation of TCE vapor by buffering the pH. Reactive transport of VOC vapors diffusing through the permeable reactive layer was modeled, including the pH effect on the oxidation rates. The model accurately described the observed breakthrough curve of TCE and toluene vapors in the headspace of the column. However, miscibility of ethanol in water in combination with produced water during oxidation made the modeling results less accurate for ethanol. A linear relationship was found between total oxidized mass of VOC vapors per unit volume of permeable reactive layer and initial water saturation. This behavior indicates that pH changes control the overall reactivity and longevity of the permeable reactive layer during oxidation of VOCs. The results suggest that field application of a horizontal permeable reactive barrier can be a viable technology against upward migration of VOC vapors through the unsaturated zone.

Prediction of monomer reactivity in radical copolymerizations from transition state quantum chemical descriptors

Directory of Open Access Journals (Sweden)

Zhengde Tan

2013-01-01

Full Text Available In comparison with the Q-e scheme, the Revised Patterns Scheme: the U, V Version (the U-V scheme has greatly improved both its accessibility and its accuracy in interpreting and predicting the reactivity of a monomer in free-radical copolymerizations. Quantitative structure-activity relationship (QSAR models were developed to predict the reactivity parameters u and v of the U-V scheme, by applying genetic algorithm (GA and support vector machine (SVM techniques. Quantum chemical descriptors used for QSAR models were calculated from transition state species with structures C¹H3 - C²HR³• or •C¹H2 - C²H2R³ (formed from vinyl monomers C¹H²=C²HR³ + H•, using density functional theory (DFT, at the UB3LYP level of theory with 6-31G(d basis set. The optimum support vector regression (SVR model of the reactivity parameter u based on Gaussian radial basis function (RBF kernel (C = 10, ε = 10- 5 and γ = 1.0 produced root-mean-square (rms errors for the training, validation and prediction sets being 0.220, 0.326 and 0.345, respectively. The optimal SVR model for v with the RBF kernel (C = 20, ε = 10- 4 and γ = 1.2 produced rms errors for the training set of 0.123, the validation set of 0.206 and the prediction set of 0.238. The feasibility of applying the transition state quantum chemical descriptors to develop SVM models for reactivity parameters u and v in the U-V scheme has been demonstrated.

A Preliminary Analysis of the Economics of Using Distributed Energy as a Source of Reactive Power Supply

Energy Technology Data Exchange (ETDEWEB)

Li, Fangxing [ORNL; Kueck, John D [ORNL; Rizy, D Tom [ORNL; King, Thomas F [ORNL

2006-04-01

operation in response to local or system operators. There are no known distributed energy asset owners currently receiving compensation for reactive power supply or capability. However, there are some cases where small generators on the generation and transmission side of electricity supply have been tested and have installed the capability to be dispatched for reactive power support. Several concerns need to be met for distributed energy to become widely integrated as a reactive power resource. The overall costs of retrofitting distributed energy devices to absorb or produce reactive power need to be reduced. There needs to be a mechanism in place for ISOs/RTOs to procure reactive power from the customer side of the meter where distributed energy resides. Novel compensation methods should be introduced to encourage the dispatch of dynamic resources close to areas with critical voltage issues. The next phase of this research will investigate in detail how different options of reactive power producing DE can compare both economically and functionally with shunt capacitor banks. Shunt capacitor banks, which are typically used for compensating reactive power consumption of loads on distribution systems, are very commonly used because they are very cost effective in terms of capital costs. However, capacitor banks can require extensive maintenance especially due to their exposure to lightning at the top of utility poles. Also, it can be problematic to find failed capacitor banks and their maintenance can be expensive, requiring crews and bucket trucks which often requires total replacement. Another shortcoming of capacitor banks is the fact that they usually have one size at a location (typically sized as 300, 600, 900 or 1200kVAr) and thus don't have variable range as do reactive power producing DE, and cannot respond to dynamic reactive power needs. Additional future work is to find a detailed methodology to identify the hidden benefit of DE for providing reactive power

Species comparison of inflammatory cell reactivity

Energy Technology Data Exchange (ETDEWEB)

Boncavage-Hennessey, E.M.; Twerdok, L.E. [Geo-Centers, Inc., Frederick, MD (United States); Finch, R.A.; Gardner, H.S. [Army Biomedical Research and Development Lab., Frederick, MD (United States)

1994-12-31

In comparison to the use of rodent models, the use of fish as a potential model to predict immune dysfunction in response to environmental contaminants is a relatively new concept. The development of a fish model for immunotoxicity is possible due to the phylogenetic conservation of many immune functions. The authors have compared mononuclear cell reactivity following in vitro stimulation among five species; Japanese medaka (Oryzias latipes), rainbow trout (Oncorhynchus mykiss), DBA/2 mice, Sprague-Dawley rats and human ML-1 cells. Mononuclear cells were isolated from the rodent bone marrow and from the teleost anterior kidney (the cell population which most closely resembles mammalian hematopoietic tissue). ML-1 cells are a myeloblastic cell line that were differentiated in vitro to monocytes/macrophages. Cell populations were characterized by myeloperoxidase and nonspecific esterase staining characteristic. Reactive oxidant production following in vitro stimulation by phorbol ester was measured using the following methods: reduction of cytochrome c (detection of extracellular superoxide), reduction of nitroblue tetrazolium (detection of intracellular superoxide) and oxidation of phenol red in the presence of horseradish peroxidase (hydrogen peroxide production). In general, teleost cells demonstrated higher superoxide anion production and mammalian cells produced higher quantities of hydrogen peroxide.

Reactive dispersive contaminant transport in coastal aquifers: Numerical simulation of a reactive Henry problem

KAUST Repository

Nick, H.M.

2013-02-01

The reactive mixing between seawater and terrestrial water in coastal aquifers influences the water quality of submarine groundwater discharge. While these waters come into contact at the seawater groundwater interface by density driven flow, their chemical components dilute and react through dispersion. A larger interface and wider mixing zone may provide favorable conditions for the natural attenuation of contaminant plumes. It has been claimed that the extent of this mixing is controlled by both, porous media properties and flow conditions. In this study, the interplay between dispersion and reactive processes in coastal aquifers is investigated by means of numerical experiments. Particularly, the impact of dispersion coefficients, the velocity field induced by density driven flow and chemical component reactivities on reactive transport in such aquifers is studied. To do this, a hybrid finite-element finite-volume method and a reactive simulator are coupled, and model accuracy and applicability are assessed. A simple redox reaction is considered to describe the degradation of a contaminant which requires mixing of the contaminated groundwater and the seawater containing the terminal electron acceptor. The resulting degradation is observed for different scenarios considering different magnitudes of dispersion and chemical reactivity. Three reactive transport regimes are found: reaction controlled, reaction-dispersion controlled and dispersion controlled. Computational results suggest that the chemical components\\' reactivity as well as dispersion coefficients play a significant role on controlling reactive mixing zones and extent of contaminant removal in coastal aquifers. Further, our results confirm that the dilution index is a better alternative to the second central spatial moment of a plume to describe the mixing of reactive solutes in coastal aquifers. © 2012 Elsevier B.V.

Application of the Firefly and Luus-Jaakola algorithms in the calculation of a double reactive azeotrope

Science.gov (United States)

Mendes Platt, Gustavo; Pinheiro Domingos, Roberto; Oliveira de Andrade, Matheus

2014-01-01

The calculation of reactive azeotropes is an important task in the preliminary design and simulation of reactive distillation columns. Classically, homogeneous nonreactive azeotropes are vapor-liquid coexistence conditions where phase compositions are equal. For homogeneous reactive azeotropes, simultaneous phase and chemical equilibria occur concomitantly with equality of compositions (in the Ung-Doherty transformed space). The modeling of reactive azeotrope calculation is represented by a nonlinear algebraic system with phase equilibrium, chemical equilibrium and azeotropy equations. This nonlinear system can exhibit more than one solution, corresponding to a double reactive azeotrope. In a previous paper (Platt et al 2013 J. Phys.: Conf. Ser. 410 012020), we investigated some numerical aspects of the calculation of reactive azeotropes in the isobutene + methanol + methyl-tert-butyl-ether (with two reactive azeotropes) system using two metaheuristics: the Luus-Jaakola adaptive random search and the Firefly algorithm. Here, we use a hybrid structure (stochastic + deterministic) in order to produce accurate results for both azeotropes. After identifying the neighborhood of the reactive azeotrope, the nonlinear algebraic system is solved using Newton's method. The results indicate that using metaheuristics and some techniques devoted to the calculation of multiple minima allows both azeotropic coordinates in this reactive system to be obtains. In this sense, we provide a comprehensive analysis of a useful framework devoted to solving nonlinear systems, particularly in phase equilibrium problems.

Application of the Firefly and Luus–Jaakola algorithms in the calculation of a double reactive azeotrope

International Nuclear Information System (INIS)

Platt, Gustavo Mendes; Domingos, Roberto Pinheiro; Andrade, Matheus Oliveira de

2014-01-01

The calculation of reactive azeotropes is an important task in the preliminary design and simulation of reactive distillation columns. Classically, homogeneous nonreactive azeotropes are vapor–liquid coexistence conditions where phase compositions are equal. For homogeneous reactive azeotropes, simultaneous phase and chemical equilibria occur concomitantly with equality of compositions (in the Ung–Doherty transformed space). The modeling of reactive azeotrope calculation is represented by a nonlinear algebraic system with phase equilibrium, chemical equilibrium and azeotropy equations. This nonlinear system can exhibit more than one solution, corresponding to a double reactive azeotrope. In a previous paper (Platt et al 2013 J. Phys.: Conf. Ser. 410 012020), we investigated some numerical aspects of the calculation of reactive azeotropes in the isobutene + methanol + methyl-tert-butyl-ether (with two reactive azeotropes) system using two metaheuristics: the Luus–Jaakola adaptive random search and the Firefly algorithm. Here, we use a hybrid structure (stochastic + deterministic) in order to produce accurate results for both azeotropes. After identifying the neighborhood of the reactive azeotrope, the nonlinear algebraic system is solved using Newton's method. The results indicate that using metaheuristics and some techniques devoted to the calculation of multiple minima allows both azeotropic coordinates in this reactive system to be obtains. In this sense, we provide a comprehensive analysis of a useful framework devoted to solving nonlinear systems, particularly in phase equilibrium problems. (paper)

The chemistry of amine radical cations produced by visible light photoredox catalysis

Directory of Open Access Journals (Sweden)

Jie Hu

2013-10-01

Full Text Available Amine radical cations are highly useful reactive intermediates in amine synthesis. They have displayed several modes of reactivity leading to some highly sought-after synthetic intermediates including iminium ions, α-amino radicals, and distonic ions. One appealing method to access amine radical cations is through one-electron oxidation of the corresponding amines under visible light photoredox conditions. This approach and subsequent chemistries are emerging as a powerful tool in amine synthesis. This article reviews synthetic applications of amine radical cations produced by visible light photocatalysis.

Integrated Design and Control of Reactive and Non-Reactive Distillation Processes

DEFF Research Database (Denmark)

Mansouri, Seyed Soheil; Sales-Cruz, Mauricio; Huusom, Jakob Kjøbsted

, an alternative approach is to tackle process design and controllability issues simultaneously, in the early stages of process design. This simultaneous synthesis approach provides optimal/near optimal operation and more efficient control of conventional (non-reactive binary distillation columns) (Hamid et al...... of methodologies have been proposed and applied on various problems to address the interactions between process design and control, and they range from optimization-based approaches to model-based methods (Sharifzadeh, 2013). In this work, integrated design and control of non-reactive distillation, ternary...... reactive distillation processes. The element concept (Pérez Cisneros et al., 1997) is used to translate a ternary system of compounds (A + B ↔ C) to a binary system of element (WA and WB). In the case of multicomponent reactive distillation processes the equivalent element concept is used to translate...

Programming Reactive Extensions and LINQ

CERN Document Server

Liberty, Jesse

2011-01-01

Pro Reactive Extensions and LINQ is a deep dive into the next important technology for .NET developers: Reactive Extensions. This in-depth tutorial goes beyond what is available anywhere else to teach how to write WPF, Silverlight, and Windows Phone applications using the Reactive Extensions (Rx) to handle events and asynchronous method calls. Reactive programming allows you to turn those aspects of your code that are currently imperative into something much more event-driven and flexible. For this reason, it's sometimes referred to as LINQ for Events. Reactive programming hinges on the concep

Chemical reactivity of potential ferrocyanide precipitates in Hanford tanks with nitrates and nitrites

International Nuclear Information System (INIS)

Scheele, R.D.; Burger, L.L.; Tingey, J.M.; Hallen, R.T.; Lilga, M.A.

1992-01-01

Ferrocyanide-bearing wastes were produced at the Hanford Site during the 1950s. Safe storage of these wastes has recently drawn increased attention. As a result of these concerns, the Pacific Northwest Laboratory was chartered to investigate the chemical reactivity and explosivity of the ferrocyanide-bearing wastes. We have investigated the thermal sensitivity of synthetic wastes and ferrocyanides and observed oxidation at 130 deg. C and explosions down to 295 deg. C. Coupled with thermodynamic calculations, these thermal studies have also shown a dependence of the reactivity on the synthetic waste composition, which is dependent on the solids settling behavior. (author)

Treatment of reactive process wastewater with high-level ammonia by blow-off method

International Nuclear Information System (INIS)

Chen Xiaotong; Quan Ying; Wang Yang; Fu Genna; Liu Bing; Tang Yaping

2012-01-01

The ceramic UO 2 kernels for nuclear fuel elements of high temperature gas cooled reactors were prepared through sol-gel process with uranyl nitrate, which produces process wastewater containing high-level ammonia and uranium. The blow-off method on a bench scale was investigated to remove ammonia from reactive wastewater. Under the optimized operating conditions, the ammonia can be removed by more than 95%, with little reactive uranium distilled. The effects of pH, heating temperature and stripping time were studied. Static tests with ion-exchange resin indicate that ammonia removal treatment increases uranium accumulation in anion exchange resin. (authors)

Adherent zirconia films by reactive ion implantation

International Nuclear Information System (INIS)

Bunker, S.N.; Armini, A.J.

1993-01-01

Conventional methods of forming ceramic coatings on metal substrates, such as CVD or plasma spray, typically retain a sharp interface and may have adhesion problems. In order to produce a completely mixed interface for better adhesion, a method using reactive ion implantation was used which can grow a thick stoichiometric film of an oxide ceramic starting from inside the substrate. Zirconium oxide ceramic films have been produced by this technique using a high-energy zirconium ion beam in an oxygen gas ambient. Compositional data are shown based on Auger electron spectroscopy of the film. Tribological properties of the layer were determined from wear and friction measurements using a pin-on-disk test apparatus. The adhesion was measured both by a scratch technique as well as by thermal shock. Results show an extremely adherent ZrO 2 film with good tribological properties

Targeted modulation of reactive oxygen species in the vascular endothelium

OpenAIRE

Shuvaev, Vladimir V.; Muzykantov, Vladimir R.

2011-01-01

Endothelial cells lining vascular luminal surface represent an important site of signaling and injurious effects of reactive oxygen species (ROS) produced by other cells and endothelium itself in ischemia, inflammation and other pathological conditions. Targeted delivery of ROS modulating enzymes conjugated with antibodies to endothelial surface molecules (vascular immunotargeting) provides site-specific interventions in the endothelial ROS, unattainable by other formulations including PEG-mo...

A comparison of in vivo and in vitro human airway reactivity to histamine.

Science.gov (United States)

Armour, C L; Lazar, N M; Schellenberg, R R; Taylor, S M; Chan, N; Hogg, J C; Paré, P D

1984-06-01

To examine for a relationship between in vivo nonspecific bronchial reactivity to histamine and in vitro smooth muscle response to histamine, we performed inhalation dose-response curves prior to lung surgery in 12 patients and compared this with their bronchial smooth muscle response in vitro. In vivo reactivity was assessed by the provocative concentration of histamine resulting in a 20% fall in forced expiratory volume in one second (PC20), and in vitro reactivity was measured by the negative log of the molar concentration of histamine producing 50% maximal contraction (pD2) as well as maximal tension generated (Tmax). In addition, morphometric analysis was performed on the in vitro tissue to quantitate the amount of smooth muscle present. A wide range of in vivo responses was found in the 12 subjects (PC20-0.065 lead to 16). There was less in vitro variability and no correlation between PC20 and in vitro reactivity assessed by pD20 or Tmax or between PC20 and the percent of smooth muscle.

Gas phase reactive collisions, experimental approach

Directory of Open Access Journals (Sweden)

Canosa A.

2012-01-01

Full Text Available Since 1937 when the first molecule in space has been identified, more than 150 molecules have been detected. Understanding the fate of these molecules requires having a perfect view of their photochemistry and reactivity with other partners. It is then crucial to identify the main processes that will produce and destroy them. In this chapter, a general view of experimental techniques able to deliver gas phase chemical kinetics data at low and very low temperatures will be presented. These techniques apply to the study of reactions between neutral reactants on the one hand and reactions involving charge species on the other hand.

A simple reactivity-meter system

International Nuclear Information System (INIS)

Ferreira, P.S.B.

1992-01-01

This paper describes a new version of a reactivity meter developed at the Institute of Nuclear Energy Research (IPEN) (Brazil). The reactivity meter computes the reactor reactivity utilizing a programmable electrometer that performs the data aquisition. The software commands the main functions of the electrometer, the data acquisition, data transfer, and reactivity calculation. The necessary hardware for this reactivity meter are a programmable electrometer, a microcomputer, and interfaces for the microcomputer to communicate with the electrometer. If it is necessary, it is possible to connect a graphic register to the microcomputer. With this conventional hardware, available in any nuclear reactor facility, one can build a powerful reactivity meter. Adding to these advantages, one can use the microcomputer on-line to analyze the data, store the data on diskettes, or create graphics

Influence of high-temperature steam on the reactivity of CaO sorbent for CO₂ capture.

Science.gov (United States)

Donat, Felix; Florin, Nicholas H; Anthony, Edward J; Fennell, Paul S

2012-01-17

Calcium looping is a high-temperature CO(2) capture technology applicable to the postcombustion capture of CO(2) from power station flue gas, or integrated with fuel conversion in precombustion CO(2) capture schemes. The capture technology uses solid CaO sorbent derived from natural limestone and takes advantage of the reversible reaction between CaO and CO(2) to form CaCO(3); that is, to achieve the separation of CO(2) from flue or fuel gas, and produce a pure stream of CO(2) suitable for geological storage. An important characteristic of the sorbent, affecting the cost-efficiency of this technology, is the decay in reactivity of the sorbent over multiple CO(2) capture-and-release cycles. This work reports on the influence of high-temperature steam, which will be present in flue (about 5-10%) and fuel (∼20%) gases, on the reactivity of CaO sorbent derived from four natural limestones. A significant increase in the reactivity of these sorbents was found for 30 cycles in the presence of steam (from 1-20%). Steam influences the sorbent reactivity in two ways. Steam present during calcination promotes sintering that produces a sorbent morphology with most of the pore volume associated with larger pores of ∼50 nm in diameter, and which appears to be relatively more stable than the pore structure that evolves when no steam is present. The presence of steam during carbonation reduces the diffusion resistance during carbonation. We observed a synergistic effect, i.e., the highest reactivity was observed when steam was present for both calcination and carbonation.

GABA from reactive astrocytes impairs memory in mouse models of Alzheimer's disease.

Science.gov (United States)

Jo, Seonmi; Yarishkin, Oleg; Hwang, Yu Jin; Chun, Ye Eun; Park, Mijeong; Woo, Dong Ho; Bae, Jin Young; Kim, Taekeun; Lee, Jaekwang; Chun, Heejung; Park, Hyun Jung; Lee, Da Yong; Hong, Jinpyo; Kim, Hye Yun; Oh, Soo-Jin; Park, Seung Ju; Lee, Hyo; Yoon, Bo-Eun; Kim, YoungSoo; Jeong, Yong; Shim, Insop; Bae, Yong Chul; Cho, Jeiwon; Kowall, Neil W; Ryu, Hoon; Hwang, Eunmi; Kim, Daesoo; Lee, C Justin

2014-08-01

In Alzheimer's disease (AD), memory impairment is the most prominent feature that afflicts patients and their families. Although reactive astrocytes have been observed around amyloid plaques since the disease was first described, their role in memory impairment has been poorly understood. Here, we show that reactive astrocytes aberrantly and abundantly produce the inhibitory gliotransmitter GABA by monoamine oxidase-B (Maob) and abnormally release GABA through the bestrophin 1 channel. In the dentate gyrus of mouse models of AD, the released GABA reduces spike probability of granule cells by acting on presynaptic GABA receptors. Suppressing GABA production or release from reactive astrocytes fully restores the impaired spike probability, synaptic plasticity, and learning and memory in the mice. In the postmortem brain of individuals with AD, astrocytic GABA and MAOB are significantly upregulated. We propose that selective inhibition of astrocytic GABA synthesis or release may serve as an effective therapeutic strategy for treating memory impairment in AD.

Elements of calculation of reactivity by numerical processing

International Nuclear Information System (INIS)

Hedde, J.

1968-01-01

In order to explore the new opportunities provided by numerical techniques, the author describes the theoretical optimal conditions of a calculation in real time of reactivity from counting samples produced by a nuclear reactor. These optimal conditions can be the better approached if a more complex processing is adopted. A compromise is to be searched between the desired precision and simplicity of the numerical processing hardware. An example is reported to assess result accuracy on a wide power evolution range with a structure of reduced complexity [fr

Toughening of Poly(lactic acid and Thermoplastic Cassava Starch Reactive Blends Using Graphene Nanoplatelets

Directory of Open Access Journals (Sweden)

Anibal Bher

2018-01-01

Full Text Available Poly(lactic acid (PLA was reactively blended with thermoplastic cassava starch (TPCS and functionalized with commercial graphene (GRH nanoplatelets in a twin-screw extruder, and films were produced by cast-film extrusion. Reactive compatibilization between PLA and TPCS phases was reached by introducing maleic anhydride and a peroxide radical during the reactive blending extrusion process. Films with improved elongation at break and toughness for neat PLA and PLA-g-TPCS reactive blends were obtained by an addition of GRH nanoplatelets. Toughness of the PLA-g-TPCS-GRH was improved by ~900% and ~500% when compared to neat PLA and PLA-g-TPCS, respectively. Crack bridging was established as the primary mechanism responsible for the improvement in the mechanical properties of PLA and PLA-g-TPCS in the presence of the nanofiller due to the high aspect ratio of GRH. Scanning electron microscopy images showed a non-uniform distribution of GRH nanoplatelets in the matrix. Transmittance of the reactive blend films decreased due to the TPCS phase. Values obtained for the reactive blends showed ~20% transmittance. PLA-GRH and PLA-g-TPCS-GRH showed a reduction of the oxygen permeability coefficient with respect to PLA of around 35% and 50%, respectively. Thermal properties, molecular structure, surface roughness, XRD pattern, electrical resistivity, and color of the films were also evaluated. Biobased and compostable reactive blend films of PLA-g-TPCS compounded with GRH nanoplatelets could be suitable for food packaging and agricultural applications.

Compounds producing an effective combinatorial regimen for disruption of HIV-1 latency.

Science.gov (United States)

Hashemi, Pargol; Barreto, Kris; Bernhard, Wendy; Lomness, Adam; Honson, Nicolette; Pfeifer, Tom A; Harrigan, P Richard; Sadowski, Ivan

2018-02-01

Highly active antiretroviral therapy (HAART) has improved the outlook for the HIV epidemic, but does not provide a cure. The proposed "shock-and-kill" strategy is directed at inducing latent HIV reservoirs, which may then be purged via boosted immune response or targeting infected cells. We describe five novel compounds that are capable of reversing HIV latency without affecting the general T-cell activation state. The new compounds exhibit synergy for reactivation of latent provirus with other latency-reversing agents (LRAs), in particular ingenol-3-angelate/PEP005. One compound, designated PH02, was efficient at reactivating viral transcription in several cell lines bearing reporter HIV-1 at different integration sites. Furthermore, it was capable of reversing latency in resting CD4 + T lymphocytes from latently infected aviremic patient cells on HAART, while producing minimal cellular toxicity. The combination of PH02 and PEP005 produces a strong synergistic effect for reactivation, as demonstrated through a quantitative viral outgrowth assay (qVOA), on CD4 + T lymphocytes from HIV-1-infected individuals. We propose that the PH02/PEP005 combination may represent an effective novel treatment for abrogating persistent HIV-1 infection. © 2017 The Authors. Published under the terms of the CC BY 4.0 license.

Reactive Programming in Java

CERN Document Server

CERN. Geneva

2017-01-01

Reactive Programming in gaining a lot of excitement. Many libraries, tools, and frameworks are beginning to make use of reactive libraries. Besides, applications dealing with big data or high frequency data can benefit from this programming paradigm. Come to this presentation to learn about what reactive programming is, what kind of problems it solves, how it solves them. We will take an example oriented approach to learning the programming model and the abstraction.

Process Improvement of Reactive Dye Synthesis Using Six Sigma Concept

Science.gov (United States)

Suwanich, Thanapat; Chutima, Parames

2017-06-01

This research focuses on the problem occurred in the reactive dye synthesis process of a global manufacturer in Thailand which producing various chemicals for reactive dye products to supply global industries such as chemicals, textiles and garments. The product named “Reactive Blue Base” is selected in this study because it has highest demand and the current chemical yield shows a high variation, i.e. yield variation of 90.4% - 99.1% (S.D. = 2.405 and Cpk = -0.08) and average yield is 94.5% (lower than the 95% standard set by the company). The Six Sigma concept is applied aiming at increasing yield and reducing variation of this process. This approach is suitable since it provides a systematic guideline with five improvement phases (DMAIC) to effectively tackle the problem and find the appropriate parameter settings of the process. Under the new parameter settings, the process yield variation is reduced to range between 96.5% - 98.5% (S.D. = 0.525 and Cpk = 1.83) and the average yield is increased to 97.5% (higher than the 95% standard set by the company).

Toxicological and pathophysiological roles of reactive oxygen and nitrogen species

International Nuclear Information System (INIS)

Roberts, Ruth A.; Smith, Robert A.; Safe, Stephen; Szabo, Csaba; Tjalkens, Ronald B.; Robertson, Fredika M.

2010-01-01

'Oxidative and Nitrative Stress in Toxicology and Disease' was the subject of a symposium held at the EUROTOX meeting in Dresden 15th September 2009. Reactive oxygen (ROS) and reactive nitrogen species (RNS) produced during tissue pathogenesis and in response to viral or chemical toxicants, induce a complex series of downstream adaptive and reparative events driven by the associated oxidative and nitrative stress. As highlighted by all the speakers, ROS and RNS can promote diverse biological responses associated with a spectrum of disorders including neurodegenerative/neuropsychiatric and cardiovascular diseases. Similar pathways are implicated during the process of liver and skin carcinogenesis. Mechanistically, reactive oxygen and nitrogen species drive sustained cell proliferation, cell death including both apoptosis and necrosis, formation of nuclear and mitochondrial DNA mutations, and in some cases stimulation of a pro-angiogenic environment. Here we illustrate the pivotal role played by oxidative and nitrative stress in cell death, inflammation and pain and its consequences for toxicology and disease pathogenesis. Examples are presented from five different perspectives ranging from in vitro model systems through to in vivo animal model systems and clinical outcomes.

Reactivity of iron-rich phyllosilicates with uranium and chromium through redox transition zones

International Nuclear Information System (INIS)

Burgos, William D.

2016-01-01

This project performed thermodynamic, kinetic, and mineral structural studies on the reactivity of phyllosilicate Fe(II/III) with metal-reducing bacteria, and with two important poly-valent DOE contaminants (chromium and uranium) that show high mobility in their oxidized state. We focused on Fe-bearing phyllosilicates because these are important components of the reactive, fines fraction of Hanford, Oak Ridge, and Idaho National Laboratory sediments. Iron-bearing phyllosilicates strongly influence the redox state and mobility of Cr and U because of their limited hydraulic conductivity, high specific surface area, and redox reactivity. This was a collaborative project between Penn State (W.D. Burgos - PI), Miami University (H. Dong - Co-PI), and Argonne National Laboratory (K. Kemner and M. Boyanov - Co-PIs). Penn State and Miami University were funded together but separately from ANL. This report summarizes research findings and publications produced by Penn State and Miami University.

Reactivity of iron-rich phyllosilicates with uranium and chromium through redox transition zones

Energy Technology Data Exchange (ETDEWEB)

Burgos, William D. [Pennsylvania State Univ., University Park, PA (United States)

2016-09-01

This project performed thermodynamic, kinetic, and mineral structural studies on the reactivity of phyllosilicate Fe(II/III) with metal-reducing bacteria, and with two important poly-valent DOE contaminants (chromium and uranium) that show high mobility in their oxidized state. We focused on Fe-bearing phyllosilicates because these are important components of the reactive, fines fraction of Hanford, Oak Ridge, and Idaho National Laboratory sediments. Iron-bearing phyllosilicates strongly influence the redox state and mobility of Cr and U because of their limited hydraulic conductivity, high specific surface area, and redox reactivity. This was a collaborative project between Penn State (W.D. Burgos – PI), Miami University (H. Dong – Co-PI), and Argonne National Laboratory (K. Kemner and M. Boyanov – Co-PIs). Penn State and Miami University were funded together but separately from ANL. This report summarizes research findings and publications produced by Penn State and Miami University.

Reactivity estimation during a reactivity-initiated accident using the extended Kalman filter

International Nuclear Information System (INIS)

Busquim e Silva, R.; Marques, A.L.F.; Cruz, J.J.; Shirvan, K.; Kazimi, M.S.

2015-01-01

Highlights: • The EKF is modeled using sophisticate strategies to make the algorithm robust and accurate. • For a supercritical reactor under RIA, the EKF presents better results compared to IPK method independent of magnitude of the noise loads. • A sensitivity for five distinct carry-over effects indicates that the EKF is less sensitive to the different set of noise. • Although the P3D/R5 simulates the reactivity using a spatial kinetics method, the use of PKRE to model the EKF provides accurate results. • The reactivity’s standard deviation is higher for the IKF method. • Under HZP (slow power response) the IPK reactivity varies widely from positive to negative values (add extra difficulty to controlling the supercritical reactor): the EKF method does not have similar behavior under the same conditions (better controlling the operation). - Abstract: This study implements the extended Kalman filter (EKF) to estimate the nuclear reactor reactivity behavior under a reactivity-initiated accident (RIA). A coupled neutronics/thermal hydraulics code PARCS/RELAP5 (P3D/R5) simulates a control rod assembly ejection (CRE) on a traditional 2272 MWt PWR to generate the reactor power profile. A MATLAB script adds random noise to the simulated reactor power. For comparison, the inverse point kinetics (IPK) deterministic method is also implemented. Three different cases of CRE are simulated and the EKF, IPK and the P3D/R5 reactivity are compared. It was found that the EKF method presents better results compared to the IPK method. Furthermore, under a RIA due to small reactivity insertion and slow power response, the IPK reactivity varies widely from positive to negative, which may add extra difficulty to the task of controlling a supercritical reactor. This feature is also confirmed by a sensitivity analysis for five different noise loads and three distinct noise measurements standard deviations (SD)

Regarding KUR Reactivity Measurement System

International Nuclear Information System (INIS)

Nakamori, Akira; Hasegawa, Kei; Tsuchiyama, Tatsuo; Yamamoto, Toshihiro; Okumura, Ryo; Sano, Tadafumi

2012-01-01

This article reported: (1) the outline of the reactivity measurement system of Kyoto University Research Reactor (KUR), (2) the calibration data of control rod, (3) the problems and the countermeasures for range switching of linear output meter. For the laptop PC for the reactivity measurement system, there are four input signals: (1) linear output meter, (2) logarithmic output meter, (3) core temperature gauge, and (4) control rod position. The hardware of reactivity measurement system is controlled with Labview installed on the laptop. Output, reactivity, reactor period, and the change in reactivity due to temperature effect or Xenon effect are internally calculated and displayed in real-time with Labview based on the four signals above. Calculation results are recorded in the form of a spreadsheet. At KUR, the reactor core arrangement was changed, so the control rod was re-calibrated. At this time, calculated and experimental values of reactivity based on the reactivity measurement system were compared, and it was confirmed that the reactivity calculation by Labview was accurate. The range switching of linear output meter in the nuclear instrumentation should automatically change within the laptop, however sometimes this did not function properly in the early stage. It was speculated that undefined percent values during the transition of percent value were included in the calculation and caused calculation errors. The range switching started working properly after fixing this issue. (S.K.)

Allergy to fish collagen: Thermostability of collagen and IgE reactivity of patients' sera with extracts of 11 species of bony and cartilaginous fish

Directory of Open Access Journals (Sweden)

Yukihiro Kobayashi

2016-10-01

Conclusions: The IgE reactivity of patients' sera to fish collagen in extracts was retained even when fish meat was treated by a high heating load. As for the fish collagen, the IgE reactivities to cartilaginous fish were lower than that to bony fish. Reducing IgE reactivity to fish meat using heat is difficult, and other modalities will be required to produce hypoallergenic fish meat.

Cardiovascular reactivity and proactive and reactive relational aggression among women with and without a history of sexual abuse.

Science.gov (United States)

Murray-Close, Dianna; Rellini, Alessandra H

2012-01-01

This study examined the association between cardiovascular reactivity and proactive and reactive functions of relational aggression among women with and without a history of sexual abuse. Heart rate reactivity, blood pressure reactivity, and respiratory sinus arrhythmia reactivity while recounting a relational stressor (e.g., being left out) were assessed. Participants provided self-reports of relational aggression and a history of sexual abuse prior to age 16. Results indicated that cardiovascular reactivity was only associated with relational aggression among women with a history of sexual abuse. In addition, whereas blunted reactivity was associated with proactive relational aggression, exaggerated reactivity was associated with reactive relational aggression. These findings highlight the importance of considering contextual moderators of the association between cardiovascular reactivity and aggression; moreover, results highlight distinct cardiovascular correlates of different functions of aggression. Finally, the findings underscore the need for additional research examining the physiological correlates of aggressive behavior among women. Copyright © 2011 Elsevier B.V. All rights reserved.

EFFECT OF REACTIVE MAGNESIUM OXIDE ON PROPERTIES OF ALKALI ACTIVATED SLAG GEOPOLYMER CEMENT PASTES

Directory of Open Access Journals (Sweden)

H. A. Abdel-Gawwad

2015-03-01

Full Text Available The effect of different proportions and different reactivities of MgO on the drying shrinkage and compressive strength of alkali activated slag pastes (AAS has been investigated. The slag was activated by 6 wt.% sodium hydroxide and liquid sodium silicate at ratio of 3:3 (wt.. The different reactivities of MgOs were produced from the calcination of hydromagnesite at different temperatures (550, 1000, 1250 C. The results showed that the reactivity of magnesium oxide decreases with increasing the calcination temperature. Also, the drying shrinkage of AAS was reduced by the replacement of slag with MgOs. The highly reactive MgO accelerated the hydration of AAS at early ages. The replacement of slag with 5% MgO550 increased one day compressive strength by ~26 % while MgO1250 had little effect. A significant increase in strength was observed after 7 days in case of replacement of slag with 5 % MgO1250. The MgO reacts with slag to form hydrotalcite likephases (Ht as detected by XRD, FTIR spectroscopy, TGA/DTG analysis and SEM.

Suspension Combustion of Wood: Influence of Pyrolysis Conditions on Char Yield, Morphology, and Reactivity

DEFF Research Database (Denmark)

Dall'Ora, Michelangelo; Jensen, Peter Arendt; Jensen, Anker Degn

2008-01-01

Chars from pine and beech wood were produced by fast pyrolysis in an entrained flow reactor and by slow pyrolysis in a thermogravimetric analyzer. The influence of pyrolysis temperature, heating rate and particle size on char yield and morphology was investigated. The applied pyrolysis temperature...... varied in the range 673−1673 K for slow pyrolysis and between 873 and 1573 K for fast pyrolysis. The chars were oxidized in a thermogravimetric analyzer and the mass loss data were used to determine char oxidation reactivity. Char yield from fast pyrolysis (104−105 K/s) was as low as 1 to 6% on a dry ash......, char oxidation reactivity decreased as pyrolysis temperature increased. The amount and composition of the ash forming matter of the wood fuels seems to play an important role in determining the differences in char yield, morphology and reactivity....

Reactive thermal waves in energetic materials

Energy Technology Data Exchange (ETDEWEB)

Hill, Larry G [Los Alamos National Laboratory

2009-01-01

Reactive thermal waves (RTWs) arise in several energetic material applications, including self-propagating high-temperature synthesis (SHS), high explosive cookoff, and the detonation of heterogeneous explosives. In this paper I exmaine ideal RTWs, by which I mean that (1) material motion is neglected, (2) the state dependence of reaction is Arrhenius in the temperature, and (3) the reaction rate is modulated by an arbitrary mass-fraction-based reaction progress function. Numerical simulations demonstrate that one's natural intuition, which is based mainly upon experience with inert materials and which leads one to expect diffusion processes to become relatively slow after a short time period, is invalid for high energy, state-sensitive reactive systems. Instead, theory predicts that RTWs can propagate at very high speeds. This result agrees with estimates for detonating heterogeneous explosives, which indicate that RTWs must spread from hot-spot nucleation sites at rates comparable to the detonation speed in order to produce experimentally-observed reaction zone thicknesses. Using dimensionless scaling and further invoking the high activation energy approximation, I obtain an analytic formula for the steady plane RTW speed from numerical calculations. I then compute the RTW speed for real explosives, and discuss aspects of their behavior.

Enhanced reactivation of UV-irradiated adenovirus 2 in HeLa cells treated with non-mutagenic chemical agents

Energy Technology Data Exchange (ETDEWEB)

Piperakis, S.M.; McLennan, A.G. (Liverpool Univ. (UK). Dept. of Biochemistry)

1985-03-01

Treatment of HeLa cells with ethanol and sodium arsenite, compounds which are known to elicit the heat-shock response, before infection with UV-irradiated adenovirus 2 has been found to result in the enhanced reactivation of the damaged virus in a manner similar to that obtained by pre-irradiation or heating of the cells. Enhanced reactivation may be the result of the inhibition of DNA synthesis caused by these agents since hydroxyurea also produced a significant enhancement.

[Hyper-reactive malarial splenomegaly].

Science.gov (United States)

Maazoun, F; Deschamps, O; Barros-Kogel, E; Ngwem, E; Fauchet, N; Buffet, P; Froissart, A

2015-11-01

Hyper-reactive malarial splenomegaly is a rare and severe form of chronic malaria. This condition is a common cause of splenomegaly in endemic areas. The pathophysiology of hyper-reactive malarial splenomegaly involves an intense immune reaction (predominantly B cell-driven) to repeated/chronic infections with Plasmodium sp. The diagnosis may be difficult, due to a poorly specific clinical presentation (splenomegaly, fatigue, cytopenias), a long delay between residence in a malaria-endemic area and onset of symptoms, and a frequent absence of parasites on conventional thin and thick blood smears. A strongly contributive laboratory parameter is the presence of high levels of total immunoglobulin M. When the diagnostic of hyper-reactive malarial splenomegaly is considered, search for anti-Plasmodium antibodies and Plasmodium nucleic acids (genus and species) by PCR is useful. Diagnosis of hyper-reactive malarial splenomegaly relies on the simultaneous presence of epidemiological, clinical, biological and follow-up findings. Regression of both splenomegaly and hypersplenism following antimalarial therapy allows the differential diagnosis with splenic lymphoma, a common complication of hyper-reactive malarial splenomegaly. Although rare in Western countries, hyper-reactive malarial splenomegaly deserves increased medical awareness to reduce the incidence of incorrect diagnosis, to prevent progression to splenic lymphoma and to avoid splenectomy. Copyright © 2015 Société nationale française de médecine interne (SNFMI). Published by Elsevier SAS. All rights reserved.

Pronounced cluster-size effects: gas-phase reactivity of bare vanadium cluster cations V(n)+ (n = 1-7) toward methanol.

Science.gov (United States)

Feyel, Sandra; Schröder, Detlef; Schwarz, Helmut

2009-05-14

Mass spectrometric experiments are used to examine the size-dependent interactions of bare vanadium cluster cations V(n)(+) (n = 1-7) with methanol. The reactivity patterns exhibit enormous size effects throughout the range of clusters investigated. For example, dehydrogenation of methanol to produce V(n)OC(+) is only brought about by clusters with n > or = 3. Atomic vanadium cation V(+) also is reactive, but instead of dehydrogenation of the alcohol, expulsions of either methane or a methyl radical take place. In marked contrast, the reaction efficiency of the dinuclear cluster V(2)(+) is extremely low. For the cluster cations V(n)(+) (n = 3-7), complete and efficient dehydrogenation of methanol to produce V(n)OC(+) and two hydrogen molecules prevails. DFT calculations shed light on the mechanism of the dehydrogenation of methanol by the smallest reactive cluster cation V(3)(+) and propose the occurrence of chemisorption concomitant with C-O bond cleavage rather than adsorption of an intact carbon monoxide molecule by the cluster.

Etching radical controlled gas chopped deep reactive ion etching

Science.gov (United States)

Olynick, Deidre; Rangelow, Ivo; Chao, Weilun

2013-10-01

A method for silicon micromachining techniques based on high aspect ratio reactive ion etching with gas chopping has been developed capable of producing essentially scallop-free, smooth, sidewall surfaces. The method uses precisely controlled, alternated (or chopped) gas flow of the etching and deposition gas precursors to produce a controllable sidewall passivation capable of high anisotropy. The dynamic control of sidewall passivation is achieved by carefully controlling fluorine radical presence with moderator gasses, such as CH.sub.4 and controlling the passivation rate and stoichiometry using a CF.sub.2 source. In this manner, sidewall polymer deposition thicknesses are very well controlled, reducing sidewall ripples to very small levels. By combining inductively coupled plasmas with controlled fluorocarbon chemistry, good control of vertical structures with very low sidewall roughness may be produced. Results show silicon features with an aspect ratio of 20:1 for 10 nm features with applicability to nano-applications in the sub-50 nm regime. By comparison, previous traditional gas chopping techniques have produced rippled or scalloped sidewalls in a range of 50 to 100 nm roughness.

Weigle Reactivation in Acinetobacter Calcoaceticus

DEFF Research Database (Denmark)

Berenstein, Dvora

1982-01-01

phage and host survivals of about 5 times 10-6 and 1 times 10-1, respectively. Intracellular development of W-reactivated P78 was followed by one-step growth experiments. Conditions which allowed maximal W-reactivation also extended the period of phage production and yielded a somewhat reduced burst......Weigle (W)-reactivation was demonstrated in Acinetobacter calcoaceticus for the UV-irra-diated lysogenic phage P78. The reactivation factor (survival of irradiated phage on irradiated bacteria/ survival on unirradiated bacteria) reached a maximum value of 20. This was obtained at UV-doses giving...

Reactive solute transport in physically and chemically heterogeneous porous media with multimodal reactive mineral facies: the Lagrangian approach.

Science.gov (United States)

Soltanian, Mohamad Reza; Ritzi, Robert W; Dai, Zhenxue; Huang, Chao Cheng

2015-03-01

Physical and chemical heterogeneities have a large impact on reactive transport in porous media. Examples of heterogeneous attributes affecting reactive mass transport are the hydraulic conductivity (K), and the equilibrium sorption distribution coefficient (Kd). This paper uses the Deng et al. (2013) conceptual model for multimodal reactive mineral facies and a Lagrangian-based stochastic theory in order to analyze the reactive solute dispersion in three-dimensional anisotropic heterogeneous porous media with hierarchical organization of reactive minerals. An example based on real field data is used to illustrate the time evolution trends of reactive solute dispersion. The results show that the correlation between the hydraulic conductivity and the equilibrium sorption distribution coefficient does have a significant effect on reactive solute dispersion. The anisotropy ratio does not have a significant effect on reactive solute dispersion. Furthermore, through a sensitivity analysis we investigate the impact of changing the mean, variance, and integral scale of K and Kd on reactive solute dispersion. Copyright © 2014 Elsevier Ltd. All rights reserved.

Miniature thermal matches: from nanoheaters to reactive fractals

International Nuclear Information System (INIS)

Rebholz, Claus; Gunduz, Ibrahim Emre; Ando, Teiichi; Doumanidis, Charalabos C

2015-01-01

Fine thermal actuation by miniature heat sources enables applications from electronics fabrication to tumor cauterization. This paper introduces the concept of nanoheaters, i.e., reactive bimetallic material dots (0D), ignited electrically to exothermically release precise heat amounts where and when needed. This concept is extended to nanoheater wires (1D) and foils (2D), as well as bulk nanoheaters (3D) manufactured via ball milling and ultrasonic consolidation of nickel and aluminum powders. The fractal structure of such powders and consolidates, with self-similar, multiscale Apollonian or lamellar packaging, is discovered to hold the key for their ignition sensitivity: nanoscale structures ignite first, to produce enough heat and raise the temperature of submicron formations, which then ignite microscale regions and so on; while inert areas quench and arrest the self-propagating exothermic reaction. Therefore, such engineered fractal reactive heaters lend themselves to affordable, high-throughput manufacture and controllable, safe, efficient, supplyless in situ thermal release. This can be transformative for innovations from self-healing composites and self-heating packages to underwater construction and mining. (paper)

Reverse-mode thermoresponsive light attenuators produced by optical anisotropic composites of nematic liquid crystals and reactive mesogens

Science.gov (United States)

Kakiuchida, Hiroshi; Ogiwara, Akifumi

2018-04-01

Polymer network liquid crystals (PNLCs) whose optical transmittance state switches between transparence at low temperatures and haze at high temperatures were fabricated from mixtures of nematic liquid crystals (LCs) and reactive mesogens (RMs). This PNLC structure is simple but effective, namely, consists of micro-scale domains of orientation-ordered LCs and anisotropically polymerized RMs. The domains form through photopolymerization induced phase separation with inhomogeneous irradiation projected by laser speckling techniques. This irradiation method enables you to control the size and shape of phase-separation domains, and these PNLCs can be applied to novel thermoresponsive optical devices; optical isolators, thermometric sheets, and smart windows.

Methods for producing thin film charge selective transport layers

Science.gov (United States)

Hammond, Scott Ryan; Olson, Dana C.; van Hest, Marinus Franciscus Antonius Maria

2018-01-02

Methods for producing thin film charge selective transport layers are provided. In one embodiment, a method for forming a thin film charge selective transport layer comprises: providing a precursor solution comprising a metal containing reactive precursor material dissolved into a complexing solvent; depositing the precursor solution onto a surface of a substrate to form a film; and forming a charge selective transport layer on the substrate by annealing the film.

MINIMAL ROLE FOR REACTIVE OXYGEN SPECIES IN DICHLOROACETIC ACID-INDUCED DYSMORPHOLOGY IN MOUSE WHOLE EMBRYO CULTURE.

Science.gov (United States)

Administration of dichloroacetate (DCA) to pregnant rats produces craniofacial, heart and other defects in their offspring. Exposure of zebrafish to DCA induces malformations and increases superoxide and nitric oxide production suggesting that reactive oxygen species (ROS) are as...

Market outlook for Australian uranium producers

International Nuclear Information System (INIS)

Lindsay, M.

2001-01-01

Recent improvements in the uranium market and political changes in Australia presented the uranium producers with their best opportunity in over 15 years. The removal of the well known 'three mines policy' by the current government has encouraged Australian producers to develop new development plans. With the expansion of the existing operations at Ranger and Olympic Dam, and the potential operations of Jabiluka, Kintyre, Koongara, Honeymoon and Beverley, Australia expects to increase annual production to 11630 t U 3 O 8 by the end of the decade. It will then join Canada as a major supplier of uranium to the world's nuclear power utilities in the 21st century. Uranium exploration, which has been virtually nonexistent over the past 15 years, has once again been reactivated. This occurred because of the change in the Government, but also because the Aboriginal groups are once more allowing exploration on their land. (author)

Multiple steady states detection in a packed-bed reactive distillation column using bifurcation analysis

DEFF Research Database (Denmark)

Ramzan, Naveed; Faheem, Muhammad; Gani, Rafiqul

2010-01-01

A packed reactive distillation column producing ethyl tert-butyl ether from tert-butyl alcohol and ethanol was simulated for detection of multiple steady states using Aspen Plus®. A rate-based approach was used to make the simulation model more realistic. A base-case was first developed and fine...

Economic analysis of reactive power compensation in a wind farm: Influence of Spanish energy policy

Energy Technology Data Exchange (ETDEWEB)

Martinez, E.; Daroca, F. [Grupo Eolicas Riojanas, Carretera de Laguardia, 91-93, 26006 Logrono, La Rioja (Spain); Sanz, F.; Blanco, J. [Department of Mechanical Engineering, University of La Rioja, Logrono, La Rioja (Spain); Jimenez, E. [Department of Electrical Engineering, University of La Rioja, Logrono, La Rioja (Spain)

2008-08-15

Presently, renewable energies and especially wind energy are gaining a special relevance in the electrical market worldwide. This current rate of growth brings with it the need for the various wind farms to not limit themselves to producing energy but also provide stability to the network within its capabilities. So, the actual objective is to adapt the installations that produce wind energy in such a way that they give a maximum amount of support in any given moment to the electrical network. For this purpose, there are governing techno-economic parameters that influence the economic behavior of commercial wind farms. A complete cost-benefit analysis model is developed, focused on incorporating automatic capacitor banks into wind farms for the compensation of reactive power. This economic analysis is about doubly fed induction generator (DFIG) wind turbines. Although this kind of wind turbines have a certain capability in terms of modulating reactive power, this capacity is not enough to achieve the new requirements of reactive power regulation in Spain and it is necessary to invest in systems of external compensation. In this paper, we have studied the case of DFIG wind turbine and capacitor banks, although the used methodology can be applied to other technologies as well by simply amplifying the algorithms according to the specific characteristics of the option elected. Following this premise, a detailed analysis of the specific needs of a wind farm has been carried out, as well as a search for the optimum performance for the compensation of reactive power. (author)

Economic analysis of reactive power compensation in a wind farm: Influence of Spanish energy policy

International Nuclear Information System (INIS)

Martinez, E.; Daroca, F.; Sanz, F.; Blanco, J.; Jimenez, E.

2008-01-01

Presently, renewable energies and especially wind energy are gaining a special relevance in the electrical market worldwide. This current rate of growth brings with it the need for the various wind farms to not limit themselves to producing energy but also provide stability to the network within its capabilities. So, the actual objective is to adapt the installations that produce wind energy in such a way that they give a maximum amount of support in any given moment to the electrical network. For this purpose, there are governing techno-economic parameters that influence the economic behavior of commercial wind farms. A complete cost-benefit analysis model is developed, focused on incorporating automatic capacitor banks into wind farms for the compensation of reactive power. This economic analysis is about doubly fed induction generator (DFIG) wind turbines. Although this kind of wind turbines have a certain capability in terms of modulating reactive power, this capacity is not enough to achieve the new requirements of reactive power regulation in Spain and it is necessary to invest in systems of external compensation. In this paper, we have studied the case of DFIG wind turbine and capacitor banks, although the used methodology can be applied to other technologies as well by simply amplifying the algorithms according to the specific characteristics of the option elected. Following this premise, a detailed analysis of the specific needs of a wind farm has been carried out, as well as a search for the optimum performance for the compensation of reactive power. (author)

Effect of cation exchange on the subsequent reactivity of lignite chars to steam. [108 references

Energy Technology Data Exchange (ETDEWEB)

Hippo, E. J.; Walker, Jr., P. L.

1977-03-01

The purpose of this investigation is to determine the role which cations in coal play in the subsequent reactivity of chars. It is hoped that this investigation will aid in an understanding of the catalytic nature of inorganic constituents in coal during its gasification. It was found that increased heat treatment temperature decreased reactivity. The decrease in reactivity was shown to be due, at least in part, to the changes in the nature of the cation with increased heat treatment temperature. Reactivity was found to be a linear function of the amount of Ca(++) exchange on the demineralized coal. The constant utilization factor over the wide range of loadings employed indicated that below 800/sup 0/C the calcium did not markedly sinter. Potassium, sodium, and calcium-containing chars were found to be much more reactive than the iron and magnesium-containing chars. However, the iron and magnesium containing chars were more reactive than chars produced from the demineralized coal. The iron char was highly active at first but the iron phase was quickly oxidized to a comparatively unreactive ..gamma..Fe/sub 2/O/sub 3/-Fe/sub 3/O/sub 4/ phase. The state of magnesium was found to be MgO. Sodium and calcium were equally active as catalysts but not as active as potassium.

Gas chromatographic analysis of reactive carbonyl compounds formed from lipids upon UV-irradiation

International Nuclear Information System (INIS)

Dennis, K.J.; Shibamoto, T.

1990-01-01

Peroxidation of lipids produces carbonyl compounds; some of these, e.g., malonaldehyde and 4-hydroxynonenal, are genotoxic because of their reactivity with biological nucleophiles. Analysis of the reactive carbonyl compounds is often difficult. The methylhydrazine method developed for malonaldehyde analysis was applied to simultaneously measure the products formed from linoleic acid, linolenic acid, arachidonic acid, and squalene upon ultraviolet-irradiation (UV-irradiation). The photoreaction products, saturated monocarbonyl, alpha,beta-unsaturated carbonyls, and beta-dicarbonyls, were derivatized with methylhydrazine to give hydrazones, pyrazolines, and pyrazoles, respectively. The derivatives were analyzed by gas chromatography and gas chromatography-mass spectrometry. Lipid peroxidation products identified included formaldehyde, acetaldehyde, acrolein, malonaldehyde, n-hexanal, and 4-hydroxy-2-nonenal. Malonaldehyde levels formed upon 4 hr of irradiation were 0.06 micrograms/mg from squalene, 2.4 micrograms/mg from linolenic acid, and 5.7 micrograms/mg from arachidonic acid. Significant levels of acrolein (2.5 micrograms/mg) and 4-hydroxy-2-nonenal (0.17 micrograms/mg) were also produced from arachidonic acid upon 4 hr irradiation

Improvement of correlated sampling Monte Carlo methods for reactivity calculations

International Nuclear Information System (INIS)

Nakagawa, Masayuki; Asaoka, Takumi

1978-01-01

Two correlated Monte Carlo methods, the similar flight path and the identical flight path methods, have been improved to evaluate up to the second order change of the reactivity perturbation. Secondary fission neutrons produced by neutrons having passed through perturbed regions in both unperturbed and perturbed systems are followed in a way to have a strong correlation between secondary neutrons in both the systems. These techniques are incorporated into the general purpose Monte Carlo code MORSE, so as to be able to estimate also the statistical error of the calculated reactivity change. The control rod worths measured in the FCA V-3 assembly are analyzed with the present techniques, which are shown to predict the measured values within the standard deviations. The identical flight path method has revealed itself more useful than the similar flight path method for the analysis of the control rod worth. (auth.)

Total OH reactivity measurements using a new fast Gas Chromatographic Photo-Ionization Detector (GC-PID

Directory of Open Access Journals (Sweden)

V. Sinha

2012-12-01

Full Text Available The primary and most important oxidant in the atmosphere is the hydroxyl radical (OH. Currently OH sinks, particularly gas phase reactions, are poorly constrained. One way to characterize the overall sink of OH is to measure directly the ambient loss rate of OH, the total OH reactivity. To date, direct measurements of total OH reactivity have been either performed using a Laser-Induced Fluorescence (LIF system ("pump-and-probe" or "flow reactor" or the Comparative Reactivity Method (CRM with a Proton-Transfer-Reaction Mass Spectrometer (PTR-MS. Both techniques require large, complex and expensive detection systems. This study presents a feasibility assessment for CRM total OH reactivity measurements using a new detector, a Gas Chromatographic Photoionization Detector (GC-PID. Such a system is smaller, more portable, less power consuming and less expensive than other total OH reactivity measurement techniques.

Total OH reactivity is measured by the CRM using a competitive reaction between a reagent (here pyrrole with OH alone and in the presence of atmospheric reactive molecules. The new CRM method for total OH reactivity has been tested with parallel measurements of the GC-PID and the previously validated PTR-MS as detector for the reagent pyrrole during laboratory experiments, plant chamber and boreal field studies. Excellent agreement of both detectors was found when the GC-PID was operated under optimum conditions. Time resolution (60–70 s, sensitivity (LOD 3–6 s⁻¹ and overall uncertainty (25% in optimum conditions for total OH reactivity were similar to PTR-MS based total OH reactivity measurements. One drawback of the GC-PID system was the steady loss of sensitivity and accuracy during intensive measurements lasting several weeks, and a possible toluene interference. Generally, the GC-PID system has been shown to produce closely comparable results to the PTR-MS and thus in suitable environments (e.g. forests it

Stress Reactivity in Insomnia.

Science.gov (United States)

Gehrman, Philip R; Hall, Martica; Barilla, Holly; Buysse, Daniel; Perlis, Michael; Gooneratne, Nalaka; Ross, Richard J

2016-01-01

This study examined whether individuals with primary insomnia (PI) are more reactive to stress than good sleepers (GS). PI and GS (n = 20 per group), matched on gender and age, completed three nights of polysomnography. On the stress night, participants received a mild electric shock and were told they could receive additional shocks during the night. Saliva samples were obtained for analysis of cortisol and alpha amylase along with self-report and visual analog scales (VAS). There was very little evidence of increased stress on the stress night, compared to the baseline night. There was also no evidence of greater stress reactivity in the PI group for any sleep or for salivary measures. In the GS group, stress reactivity measured by VAS scales was positively associated with an increase in sleep latency in the experimental night on exploratory analyses. Individuals with PI did not show greater stress reactivity compared to GS.

Reactive sputter deposition

CERN Document Server

Mahieu, Stijn

2008-01-01

In this valuable work, all aspects of the reactive magnetron sputtering process, from the discharge up to the resulting thin film growth, are described in detail, allowing the reader to understand the complete process. Hence, this book gives necessary information for those who want to start with reactive magnetron sputtering, understand and investigate the technique, control their sputtering process and tune their existing process, obtaining the desired thin films.

Reactive power supply by distributed generators

OpenAIRE

Braun, M.

2008-01-01

Distributed reactive power supply is necessary in distribution networks for an optimized network operation. This paper presents first the reactive power supply capabilities of generators connected to the distribution network (distributed generators). In a second step an approach is proposed of determining the energy losses resulting from reactive power supply by distributed generators. The costs for compensating these losses represent the operational costs of reactive power supply. These cost...

Reactive programming in eventsourcing systems

OpenAIRE

Kučinskas, Žilvinas

2017-01-01

Eventsourcing describes current state as series of events that occurred in a system. Events hold all information that is needed to recreate current state. This method allows to achieve high volume of transactions, and enables efficient replication. Whereas reactive programming lets implement reactive systems in declarative style, decomposing logic into smaller, easier to understand components. Thesis aims to create reactive programming program interface, incorporating both principles. Applyin...

Mood reactivity rather than cognitive reactivity is predictive of depressive relapse: a randomized study with 5.5-year follow-up

NARCIS (Netherlands)

van Rijsbergen, Gerard D.; Bockting, Claudi L. H.; Burger, Huibert; Spinhoven, Philip; Koeter, Maarten W. J.; Ruhé, Henricus G.; Hollon, Steven D.; Schene, Aart H.

2013-01-01

The current study examined whether cognitive reactivity, cognitive extremity reactivity, and mood reactivity following mood provocation predicted relapse in depression over 5.5 years. Additionally, this study was the 1st to examine whether changes in cognitive reactivity and mood reactivity

Processing of polymers using reactive solvents

NARCIS (Netherlands)

Lemstra, P.J.; Kurja, J.; Meijer, H.E.H.; Meijer, H.E.H.

1997-01-01

A review with many refs. on processing of polymers using reactive solvents including classification of synthetic polymers, guidelines for the selection of reactive solvents, basic aspects of processing, examples of intractable and tractable polymer/reactive solvent system

Definition of reactivity and its measurability

International Nuclear Information System (INIS)

Hu Dapu

1986-01-01

Reactivity is the fundamental and important physical quantity in the reactor physics. The different kinds of method for defining reactivity are represented, the difference between different definitions of reactivity is indicalted and the conditions under which they have nearly the same measurable value are discussed. It is demonstrated that when the static adjointed neutron density or the neutron importance is selected to be a weight function for generating kinetic parameters used in the neutron kinetic equations, the kinetic reactivity is approximately equal to the static reactivity. Due to the constraint of the normalization condition, the shape function must be so selected that the corresponding amplitude function is proportional to the fundamental mode of neutron density variating with time. Measured reactivity by the kinetic method may vary with the position of detector, owing to the different space distribution of the prompt neutrons density and the delayed neutrons density and the effect of the higher harmonics of the neutron density. Some corresponding correction must be made in order to obtain the real static reactivity

Electrospinning of reactive mesogens

NARCIS (Netherlands)

Yao, J.; Picot, O.T.; Hughes-Brittain, N.F.; Bastiaansen, C.W.M.; Peijs, T.

2016-01-01

The reinforcement potential of reactive liquid crystals or reactive mesogens (RMs) in electrospun fibers was investigated through the blending of two types of RMs (RM257 and RM82) with two types of thermoplastics; polyamide 6 (PA6) and poly(methyl methacrylate) (PMMA). Polymer/RM blends were

Engine combustion control via fuel reactivity stratification

Science.gov (United States)

Reitz, Rolf Deneys; Hanson, Reed M; Splitter, Derek A; Kokjohn, Sage L

2013-12-31

A compression ignition engine uses two or more fuel charges having two or more reactivities to control the timing and duration of combustion. In a preferred implementation, a lower-reactivity fuel charge is injected or otherwise introduced into the combustion chamber, preferably sufficiently early that it becomes at least substantially homogeneously dispersed within the chamber before a subsequent injection is made. One or more subsequent injections of higher-reactivity fuel charges are then made, and these preferably distribute the higher-reactivity matter within the lower-reactivity chamber space such that combustion begins in the higher-reactivity regions, and with the lower-reactivity regions following thereafter. By appropriately choose the reactivities of the charges, their relative amounts, and their timing, combustion can be tailored to achieve optimal power output (and thus fuel efficiency), at controlled temperatures (and thus controlled NOx), and with controlled equivalence ratios (and thus controlled soot).

Pattern transfer on fused silica samples using sub-aperture reactive ion beam etching

Energy Technology Data Exchange (ETDEWEB)

Miessler, Andre; Arnold, Thomas [Leibniz-Institut fuer Oberflaechenmodifizierung (IOM), Permoserstrasse 15, D-04318 Leipzig (Germany)

2012-07-01

In comparison to sole Ar ion beam sputtering Reactive Ion Beam Etching (RIBE) reveals the main advantage of increasing the selectivity for different kind of materials due to chemical contributions during the material removal. Therefore RIBE is qualified to be an excellent candidate for pattern transfer applications. The goal of the present study is to apply a sub-aperture reactive ion beam for pattern transfer on large fused silica samples. Concerning this matter, the etching behavior in the ion beam periphery plays a decisive role. Using a Kaufman-typed ion source with NF{sub 3} as reactive gas, XPS measurements of the modified surface exposes impurities like Ni, Fe and Cr, which belongs to chemically eroded material of the plasma pot and a layer formation of silicon nitride, handicaps the etching process mainly in the beam periphery where the sputtering contribution decrease. These side effects influence the pattern transfer of trench structures, produced in AZ MIR 701 photoresist by lithography on a 2'' fused silica plate, by changing the selectivity due to modified chemical reactions of the resist layer. Concerning this we investigate a RF-Ion source for sub aperture reactive ion beam applications and finally we examine the pattern transfer on large fused silica plates using NF{sub 3}-sub-aperture RIBE.

Effects of methyl group on aromatic hydrocarbons on the nanostructures and oxidative reactivity of combustion-generated soot

KAUST Repository

Guerrero Peñ a, Gerardo D.J.; Alrefaai, Mhd Maher; Yang, Seung Yeon; Raj, Abhijeet; Brito, Joaquin L.; Stephen, Samuel; Anjana, Tharalekshmy; Pillai, Vinu; Al Shoaibi, Ahmed; Chung, Suk-Ho

2016-01-01

The substituted and unsubstituted aromatic hydrocarbons, present in transportation fuels such as gasoline and diesel, are thought to be responsible for most of the soot particles produced during their combustion. However, the effects of the substituted alkyl groups on the aromatic hydrocarbons on their sooting tendencies, and on the physical and chemical properties of soot produced from them are not well understood. In this work, the effect of the presence of methyl groups on aromatic hydrocarbons on their sooting propensity, and on the oxidative reactivity, morphology, and chemical composition of soot generated from them in diffusion flames is studied using benzene, toluene, and m-xylene as fuels. Several experimental techniques including high resolution transmission electron microscopy and X-ray diffraction are used to identify the morphological changes in soot, whereas the elemental and thermo-gravimetric analyses, electron energy loss spectroscopy, and Fourier transform infrared spectroscopy are used to study the changes in its chemical properties and reactivity. The activation energies for soot oxidation are calculated at different conversion levels, and a trend in the reactivity of soots from benzene, toluene and m-xylene is reported. It is observed that the sizes of primary particles and graphene-like sheets, and the concentrations of aliphatics and oxygenated groups in soot particles decreased with the addition of methyl group(s) on the aromatic ring. The physicochemical changes in soot are found to support the oxidative reactivity trends. © 2016 The Combustion Institute

Effects of methyl group on aromatic hydrocarbons on the nanostructures and oxidative reactivity of combustion-generated soot

KAUST Repository

Guerrero Peña, Gerardo D.J.

2016-07-23

The substituted and unsubstituted aromatic hydrocarbons, present in transportation fuels such as gasoline and diesel, are thought to be responsible for most of the soot particles produced during their combustion. However, the effects of the substituted alkyl groups on the aromatic hydrocarbons on their sooting tendencies, and on the physical and chemical properties of soot produced from them are not well understood. In this work, the effect of the presence of methyl groups on aromatic hydrocarbons on their sooting propensity, and on the oxidative reactivity, morphology, and chemical composition of soot generated from them in diffusion flames is studied using benzene, toluene, and m-xylene as fuels. Several experimental techniques including high resolution transmission electron microscopy and X-ray diffraction are used to identify the morphological changes in soot, whereas the elemental and thermo-gravimetric analyses, electron energy loss spectroscopy, and Fourier transform infrared spectroscopy are used to study the changes in its chemical properties and reactivity. The activation energies for soot oxidation are calculated at different conversion levels, and a trend in the reactivity of soots from benzene, toluene and m-xylene is reported. It is observed that the sizes of primary particles and graphene-like sheets, and the concentrations of aliphatics and oxygenated groups in soot particles decreased with the addition of methyl group(s) on the aromatic ring. The physicochemical changes in soot are found to support the oxidative reactivity trends. © 2016 The Combustion Institute

Ecofriendly degradation of sulfonated diazo dye C.I. Reactive Green 19A using Micrococcus glutamicus NCIM-2168.

Science.gov (United States)

Saratale, R G; Saratale, G D; Chang, J S; Govindwar, S P

2009-09-01

Micrococcus glutamicus NCIM-2168 exhibited complete decolorization and degradation of C.I. Reactive Green 19A (an initial concentration of 50 mg l(-1)) within 42 h at temperature 37 degrees C and pH 8, under static condition. Extent of mineralization was determined with total organic carbon (TOC) and chemical oxygen demand (COD) measurement, showing a satisfactory reduction of TOC (72%) and COD (66%) within 42 h. Enzyme studies shows involvement of oxidoreductive enzymes in decolorization/degradation process. Analytical studies of the extracted metabolites confirmed the significant degradation of Reactive Green 19A into various metabolites. The microbial toxicity and phytotoxicity assay revealed that the degradation of Reactive Green 19A produced nontoxic metabolites. In addition, the M. glutamicus strain was applied to decolorize a mixture of ten reactive dyes showing a 63% decolorization (in terms of decrease in ADMI value) within 72 h, along with 48% and 42% reduction in TOC and COD under static condition.

Real-time in vivo detection of biomaterial-induced reactive oxygen species

OpenAIRE

Liu, Wendy F.; Ma, Minglin; Bratlie, Kaitlin M.; Dang, Tram T.; Langer, Robert; Anderson, Daniel G.

2010-01-01

The non-specific host response to implanted biomaterials is often a key challenge of medical device design. To evaluate biocompatibility, measuring the release of reactive oxygen species (ROS) produced by inflammatory cells in response to biomaterial surfaces is a well-established method. However, the detection of ROS in response to materials implanted in vivo has not yet been demonstrated. Here, we develop a bioluminescence whole animal imaging approach to observe ROS released in response to...

Biodecolorization and biodegradation of Reactive Blue by ...

African Journals Online (AJOL)

SERVER

2007-06-18

Jun 18, 2007 ... Aspergillus sp. effectively decolorized Reactive Blue and other structurally different synthetic dyes. Agitation was found to be an important ... Few chemically different dyes such as Reactive Black (75%), Reactive Yellow (70%),. Reactive Red (33%) and ..... Degradation of azo dyes by the lignin degrading ...

Significance of isolated reactive treponemal chemiluminescence immunoassay results.

Science.gov (United States)

Hunter, Michael G; Robertson, Peter W; Post, Jeffrey J

2013-05-01

Isolated reactive serum treponemal chemiluminescence immunoassay (CIA) specimens cause clinical uncertainty. Sera were screened by CIA, and reactive samples underwent reflex testing with rapid plasma reagin (RPR), Treponema pallidum particle agglutination (TPPA), and fluorescent treponemal antibody absorption (FTA Abs) assays. Samples reactive only on the CIA were deemed "isolated" reactive CIA samples. We undertook detailed review of a subset of subjects with isolated reactive CIA specimens. Of 28 261 specimens, 1171 (4.1%) were reactive on CIA, of which 133 (11.3%) had isolated CIA reactivity. Most subjects (66 of 82 [80.5%]) with isolated reactive CIA specimens were from high-prevalence populations. We found evidence of CIA, TPPA, and FTA Abs seroreversion. The median chemiluminescent signal-to-cutoff ratio was similar for isolated reactive CIA sera and sera that were reactive on either FTA Abs or TPPA assays (2.19 vs 2.32; P = .15) but lower than for sera reactive on both FTA Abs and TPPA assays (12.37; P < .001) or for sera reactive on RPR assays (25.53; P < .001). A total of 11 of 20 patients (55%) with an isolated reactive CIA specimen who underwent medical record review had previous or subsequent evidence of syphilis infection. Isolated reactive CIA specimens may represent true T. pallidum infection and may be found after seroreversion of traditional treponemal assays.

Pretreatment of cellulosic wastes to increase enzyme reactivity

Energy Technology Data Exchange (ETDEWEB)

Neese, N.; Wallick, J.; Harper, J.M.

1977-03-01

The enzymatic hydrolysis of cellulose to glucose is generally a slow reaction. Different pretreatments, such as ball milling to a -200 mesh or swelling in 1 to 2 percent NaOH are reported to increase the reactivity considerably. In this work a fiber fraction from cattle manure was treated in an autoclave for 5 to 30 min at temperatures ranging from 130 to 200/sup 0/C. The reactivity of the cellulose, measured by incubating samples with a commercial cellulase preparation for one hour at 50/sup 0/C and pH 4.8, was increased by a factor of 4 to 6 compared to NaOH treatment and 10 to 20 compared to untreated fiber. The increased reaction rate is probably mostly due to an increase in cellulose availability to enzymatic attack, as structural hemicellulose is hydrolyzed and removed during the treatment. Sugars, produced by hemicellulosis hydrolysis, will react further to give caramelization products. These side reactions were shown to be suppressed by short treatment times. The treated fiber could support growth of a mixed culture of Trichoderma viride and Candida utilis only after washing, indicating the formation of water soluble inhibitory products during treatment. The treatment with high-temperature steam can probably be used also with other cellulosic materials to increase reactivity. This may be an attractive way to prepare low-valued wastes such as manure fibers, straw, stalks, or corn cobs for fermentation processes to increase the protein content or for use directly as ruminant animal feed.

Event-Based Modularization of Reactive Systems

NARCIS (Netherlands)

Malakuti Khah Olun Abadi, Somayeh; Aksit, Mehmet

2014-01-01

There is a large number of complex software systems that have reactive behavior. As for any other software system, reactive systems are subject to evolution demands. This paper defines a set requirements that must be fulfilled so that reuse of reactive software systems can be increased. Detailed

Obtaining incremental multigroup cross sections for CANDU super cells with reactivity devices

International Nuclear Information System (INIS)

Balaceanu, V.; Constantin, M.

2001-01-01

In the last 20 years a multigroup methodology WIMS - PIJXYZ (WP) was developed and validated at INR Pitesti for obtaining incremental cross sections for reactivity devices in CANDU reactors. This is an alternate methodology to the CANDU classic methodology (experimentally adjusted) based on the POWDERPUFS and MULTICELL computer codes. The 2D supercell calculation performed with the WIMS code, that is a NEA Data Bank transport code, and which produces multigroup cross sections (on 18 energy groups) for CANDU supercell material (standard and perturbed, with and without reactivity devices). To obtain an as correct as possible 3D modelling for the CANDU supercells containing reactivity devices, the WIMS cross sections are used as input data for the PIJXYZ code, thus obtaining homogenized cross sections for CANDU supercells. PIJXYZ is an integral transport code based on the formalism of the first collision probabilities. It is analogue to the SHETAN code and it was created for neutron analyzes at cell level for CANDU type reactors were the reactivity devices are perpendicular to the fuel channels. The coordinate system used in PIJXYZ is a mixed one, namely a rectangular-cylindrical system. The geometric model used in PIJXYZ is presented. The fuel beam is represented by a horizontal cylinder and the reactivity device by a vertical one both cylinders being immersed in the moderator. Two supercell types were considered: a perturbed supercell (containing a reactivity device) and the standard supercell were the place of reactivity device is occupied by the moderator. The incremental cross sections for reactivity device are obtained as differences between the homogenized over supercell cross sections (with reactivity device) and homogenized over standards supercell (without device) cross sections. The PIJXYZ computation may be done on an energy cutting with 2 up to 18 groups. The validation of VIMS - PIJXYZ was done on the basis of several benchmark and by comparison with

Acrolein: An Effective Biomarker for Tissue Damage Produced from Polyamines.

Science.gov (United States)

Igarashi, Kazuei; Uemura, Takeshi; Kashiwagi, Keiko

2018-01-01

It is thought that the major factor responsible for cell damage is reactive oxygen species (ROS), but our recent studies have shown that acrolein (CH 2 =CH-CHO) produced from spermine and spermidine is more toxic than ROS. Thus, (1) the mechanism of acrolein production during brain stroke, (2) one of the mechanisms of acrolein toxicity, and (3) the role of glutathione in acrolein detoxification are described in this chapter.

Effects on nano zero-valent iron reactivity of interactions between hardness, alkalinity, and natural organic matter in reverse osmosis concentrate

DEFF Research Database (Denmark)

Hwang, Yuhoon; Shin, Hang-Sik

2013-01-01

, the influence of hardness, alkalinity, and organic matter on NZVI reactivity was evaluated by the response surface method (RSM). Hardness (Ca2 ) had a positive effect on NZVI reactivity by accelerating iron corrosion. In contrast, alkalinity (bicarbonate; HCO3-) and organic matter (humic acid; HA) had negative...... effects on NZVI reactivity due to morphological change to carbonate green rust, and to competitive adsorption of HA, respectively. The validity of the statistical prediction model derived from RSM was confirmed by an additional confirmation experiment, and the experimental result was within the 95......% confidential interval. Therefore, it can be said that the RSM model produced results that were statistically significant....

Spring 5 & reactive streams

CERN Multimedia

CERN. Geneva; Clozel, Brian

2017-01-01

Spring is a framework widely used by the world-wide Java community, and it is also extensively used at CERN. The accelerator control system is constituted of 10 million lines of Java code, spread across more than 1000 projects (jars) developed by 160 software engineers. Around half of this (all server-side Java code) is based on the Spring framework. Warning: the speakers will assume that people attending the seminar are familiar with Java and Spring’s basic concepts. Spring 5.0 and Spring Boot 2.0 updates (45 min) This talk will cover the big ticket items in the 5.0 release of Spring (including Kotlin support, @Nullable and JDK9) and provide an update on Spring Boot 2.0, which is scheduled for the end of the year. Reactive Spring (1h) Spring Framework 5.0 has been released - and it now supports reactive applications in the Spring ecosystem. During this presentation, we'll talk about the reactive foundations of Spring Framework with the Reactor project and the reactive streams specification. We'll al...

Making real-time reactive systems reliable

Science.gov (United States)

Marzullo, Keith; Wood, Mark

1990-01-01

A reactive system is characterized by a control program that interacts with an environment (or controlled program). The control program monitors the environment and reacts to significant events by sending commands to the environment. This structure is quite general. Not only are most embedded real time systems reactive systems, but so are monitoring and debugging systems and distributed application management systems. Since reactive systems are usually long running and may control physical equipment, fault tolerance is vital. The research tries to understand the principal issues of fault tolerance in real time reactive systems and to build tools that allow a programmer to design reliable, real time reactive systems. In order to make real time reactive systems reliable, several issues must be addressed: (1) How can a control program be built to tolerate failures of sensors and actuators. To achieve this, a methodology was developed for transforming a control program that references physical value into one that tolerates sensors that can fail and can return inaccurate values; (2) How can the real time reactive system be built to tolerate failures of the control program. Towards this goal, whether the techniques presented can be extended to real time reactive systems is investigated; and (3) How can the environment be specified in a way that is useful for writing a control program. Towards this goal, whether a system with real time constraints can be expressed as an equivalent system without such constraints is also investigated.

Inhibition of transcription and translation in the striatum after memory reactivation: Lack of evidence of reconsolidation.

Science.gov (United States)

Prado-Alcalá, Roberto A; Medina, Andrea Cristina; Bello-Medina, Paola C; Quirarte, Gina L

2017-07-01

It has been found that interference with neural activity after a consolidated memory is retrieved produces an amnestic state; this has been taken has indicative of destabilization of the memory trace that would have been produced by a process of reconsolidation (allowing for maintenance of the original trace). However, a growing body of evidence shows that this is not a reliable effect, and that it is dependent upon some experimental conditions, such as the age of the memory, memory reactivation procedures, the predictability of the reactivation stimulus, and strength of training. In some instances, where post-retrieval treatments induce a retention deficit (which would be suggestive of interference with reconsolidation), memory is rescued by simple passing of time or by repeated retention tests. We now report that post-training and post-retrieval inhibition of transcription and translation in dorsal striatum, a structure where both of these manipulations have not been studied, produce interference with consolidation and a transitory retention deficit, respectively. These results do not give support to the reconsolidation hypothesis and lead to the conclusion that the post-activation deficiencies are due to interference with retrieval of information. Copyright © 2016 Elsevier Inc. All rights reserved.

Cross-reactivity of human nickel-reactive T-lymphocyte clones with copper and palladium

NARCIS (Netherlands)

Pistoor, F. H.; Kapsenberg, M. L.; Bos, J. D.; Meinardi, M. M.; von Blomberg, M. E.; Scheper, R. J.

1995-01-01

Twenty Ni-reactive T-lymphocyte clones were obtained from eight different donors and analyzed for their ability to cross-react with other metals. All Ni-reactive T-lymphocyte clones were CD4+CD8- and recognized Ni in association with either HLA-DR or -DQ molecules. Based on the periodic table of the

Recovery of succinic acid produced by fermentation of a metabolically engineered Mannheimia succiniciproducens strain.

Science.gov (United States)

Song, Hyohak; Huh, Yun Suk; Lee, Sang Yup; Hong, Won Hi; Hong, Yeon Ki

2007-12-01

There have recently been much advances in the production of succinic acid, an important four-carbon dicarboxylic acid for many industrial applications, by fermentation of several natural and engineered bacterial strains. Mannheimia succiniciproducens MBEL55E isolated from bovine rumen is able to produce succinic acid with high efficiency, but also produces acetic, formic and lactic acids just like other anaerobic succinic acid producers. We recently reported the development of an engineered M. succiniciproducens LPK7 strain which produces succinic acid as a major fermentation product while producing much reduced by-products. Having an improved succinic acid producer developed, it is equally important to develop a cost-effective downstream process for the recovery of succinic acid. In this paper, we report the development of a simpler and more efficient method for the recovery of succinic acid. For the recovery of succinic acid from the fermentation broth of LPK7 strain, a simple process composed of a single reactive extraction, vacuum distillation, and crystallization yielded highly purified succinic acid (greater than 99.5% purity, wt%) with a high yield of 67.05wt%. When the same recovery process or even multiple reactive extraction steps were applied to the fermentation broth of MBEL55E, lower purity and yield of succinic acid were obtained. These results suggest that succinic acid can be purified in a cost-effective manner by using the fermentation broth of engineered LPK7 strain, showing the importance of integrating the strain development, fermentation and downstream process for optimizing the whole processes for succinic acid production.

Mindful attention predicts greater recovery from negative emotions, but not reduced reactivity.

Science.gov (United States)

Cho, Sinhae; Lee, Hyejeen; Oh, Kyung Ja; Soto, José A

2017-09-01

This study investigated the role of dispositional mindful attention in immediate reactivity to, and subsequent recovery from, laboratory-induced negative emotion. One hundred and fourteen undergraduates viewed blocks of negative pictures followed by neutral pictures. Participants' emotional responses to negative pictures and subsequent neutral pictures were assessed via self-reported ratings. Participants' emotional response to negative pictures was used to index level of emotional reactivity to unpleasant stimuli; emotional response to neutral pictures presented immediately after the negative pictures was used to index level of emotional recovery from pre-induced negative emotion (residual negativity). Results indicated that mindful attention was not associated with the emotional response to negative pictures, but it was associated with reduced negative emotion in response to the neutral pictures presented immediately after the negative pictures, suggesting better recovery as opposed to reduced reactivity. This effect was especially pronounced in later experimental blocks when the accumulation of negative stimuli produced greater negative emotion from which participants had to recover. The current study extends previous findings on the relationship between dispositional mindfulness and reduced negative emotion by demonstrating that mindful attention may facilitate better recovery from negative emotion, possibly through more effective disengagement from previous stimuli.

Clarifying the Role of Reactive Oxygen Species and Reported Effects of Low-Dose Ionizing Radiation on Cells - Clarifying the Role of Reactive Oxygen Species in Producing the Reported Effects of Low-Dose Ionizing Radiation on Cells

Energy Technology Data Exchange (ETDEWEB)

Willey, Neil J. [Centre for Research In Biosciences, University of the West of England, Coldharbour Lane, Frenchay, Bristol BS16 1QY (United Kingdom)

2014-07-01

Chronic low doses of ionizing radiation (IR) to cells, such as those that occur in contaminated environments, are widely reported to produce a variety of effects, from adverse effects to no effects to positive effects. In addition, bystander effects have been reported in some studies. For only relatively few of these effects have mechanistic explanations been reported but in many of those for which they have, reactive oxygen species (ROS) and/or the anti-oxidants that help to control their effects, have often been suggested to have a role. In general, it is assumed that either radiolysis of water or stress due to IR cause an increase in ROS and/or anti-oxidant activity, and hence the observed effects. The role of ROS in producing the effects reported at chronic low doses of radiation has infrequently been tested at either a theoretical or experimental level. Here we use a dynamic model of anti-oxidant capacity in cells to test the theoretical underpinnings of the ROS hypothesis together with genomic and proteomic experiments using Arabidopsis thaliana to test the molecular effects of IR in cells. The published model we have constructed for testing the interaction of IR and anti-oxidant systems (Smith et al, 2012) first calculates the amount of ROS produced by IR. Overall, at the dose rates that occur in contaminated environments the amount of ROS produced by IR is extremely small, certainly much smaller than is routinely produced in a cell during many metabolic processes. ROS from respiration leak out of mitochondria at significant rates and in plant cells ROS also leak out of photo-synthesizing chloroplasts. Although there is a variety of anti-oxidants in many cells, the nexus of their capacity is glutathione (GSH) which ultimately derives its reducing power from NADPH. We thus modeled the anti-oxidative capacity of a cell from the activity GSH and used predicted concentrations of ROS from IR to calculate the oxidative stress that they would cause via the

Influence of the void fraction in the linear reactivity model

International Nuclear Information System (INIS)

Castillo, J.A.; Ramirez, J.R.; Alonso, G.

2003-01-01

The linear reactivity model allows the multicycle analysis in pressurized water reactors in a simple and quick way. In the case of the Boiling water reactors the void fraction it varies axially from 0% of voids in the inferior part of the fuel assemblies until approximately 70% of voids to the exit of the same ones. Due to this it is very important the determination of the average void fraction during different stages of the reactor operation to predict the burnt one appropriately of the same ones to inclination of the pattern of linear reactivity. In this work a pursuit is made of the profile of power for different steps of burnt of a typical operation cycle of a Boiling water reactor. Starting from these profiles it builds an algorithm that allows to determine the voids profile and this way to obtain the average value of the same one. The results are compared against those reported by the CM-PRESTO code that uses another method to carry out this calculation. Finally, the range in which is the average value of the void fraction during a typical cycle is determined and an estimate of the impact that it would have the use of this value in the prediction of the reactivity produced by the fuel assemblies is made. (Author)

Mood reactivity rather than cognitive reactivity is predictive of depressive relapse : a randomized study with 5.5-year follow-up

NARCIS (Netherlands)

van Rijsbergen, Gerard D; Bockting, Claudi L H; Burger, Huibert; Spinhoven, Philip; Koeter, Maarten W J; Ruhe, Eric; Hollon, Steven D; Schene, Aart H

OBJECTIVE: The current study examined whether cognitive reactivity, cognitive extremity reactivity, and mood reactivity following mood provocation predicted relapse in depression over 5.5 years. Additionally, this study was the 1st to examine whether changes in cognitive reactivity and mood

Elevated and cross‐responsive CD1a‐reactive T cells in bee and wasp venom allergic individuals

Science.gov (United States)

Subramaniam, Sumithra; Aslam, Aamir; Misbah, Siraj A.; Salio, Mariolina; Cerundolo, Vincenzo; Moody, D Branch

2015-01-01

The role of CD1a‐reactive T cells in human allergic disease is unknown. We have previously shown that circulating CD1a‐reactive T cells recognize neolipid antigens generated by bee and wasp venom phospholipase, and here tested the hypothesis that venom‐responsive CD1a‐reactive T cells associate with venom allergy. Circulating T cells from bee and wasp venom allergic individuals, before and during immunotherapy, were exposed to CD1a‐transfected K562 cells in the presence of wasp or bee venom. T‐cell response was evaluated based on IFNγ, GM‐CSF, and IL‐13 cytokine production. Venom allergic individuals showed significantly higher frequencies of IFN‐γ, GM‐CSF, and IL‐13 producing CD1a‐reactive T cells responsive to venom and venom‐derived phospholipase than healthy individuals. Venom‐responsive CD1a‐reactive T cells were cross‐responsive between wasp and bee suggesting shared pathways of allergenicity. Frequencies of CD1a‐reactive T cells were initially induced during subcutaneous immunotherapy, peaking by weeks 5, but then reduced despite escalation of antigen dose. Our current understanding of venom allergy and immunotherapy is largely based on peptide and protein‐specific T cell and antibody responses. Here, we show that lipid antigens and CD1a‐reactive T cells associate with the allergic response. These data have implications for mechanisms of allergy and approaches to immunotherapy. PMID:26518614

A roadmap for OH reactivity research

Science.gov (United States)

Williams, Jonathan; Brune, William

2015-04-01

A fundamental property of the atmosphere is the frequency of gas-phase reactions with the OH radical, the atmosphere's primary oxidizing agent. This reaction frequency is called the OH reactivity and is the inverse the lifetime of the OH radical itself, which varies from a few seconds in the clean upper troposphere to below 10 ms in forests and polluted city environments. Ever since the discovery of the OH radical's importance to tropospheric chemistry, the characterization of its overall loss rate (OH reactivity) has remained a key question. At first, this property was assessed by summing the reactivity contributions of individually measured compounds; however, as improving analytical technology revealed ever more reactive species in ambient air, it became clear that this approach could provide only a lower limit. Approximately 15 years ago, the direct measurement of total OH reactivity was conceived independently by two groups. The first publications demonstrated direct OH reactivity measurements in the laboratory (Calpini et al., 1999) based on LIDAR and in the ambient air (Kovacs and Brune, 2001) based on in situ laser induced fluorescence detection of OH.

Ultrahigh reactivity and grave nanotoxicity of copper nanoparticles

International Nuclear Information System (INIS)

Huan Meng; Zhen Chen; Chengcheng Zhang; Yun Wang; Yuliang Zhao

2007-01-01

Recently, it was reported that the toxicity of copper particles increases with the decrease of the particle size on a mass basis. To understand this phenomenon, inductively coupled plasma mass spectrometry (ICP-MS) techniques and in vitro chemical studies were carried out to explore how they produce toxicity in vivo. The results suggest that when the sizes of particles become small and down to a nanoscale, copper becomes extremely reactive in a simulative intracorporeal environment. The nanosized copper particles consume the hydrogen ions in stomach more quickly than micron ones. These processes further convert the copper nanoparticles into cupric ions whose toxicity is very high in vivo. (author)

Borylnitrenes: electrophilic reactive intermediates with high reactivity towards C-H bonds.

Science.gov (United States)

Bettinger, Holger F; Filthaus, Matthias

2010-12-21

Borylnitrenes (catBN 3a and pinBN 3b; cat = catecholato, pin = pinacolato) are reactive intermediates that show high tendency towards insertion into the C-H bonds of unactivated hydrocarbons. The present article summarizes the matrix isolation investigations that were aimed at identifying, characterizing and investigating the chemical behaviour of 3a by spectroscopic means, and of the experiments in solution and in the gas phase that were performed with 3b. Comparison with the reactivity reported for difluorovinylidene 1a in solid argon indicates that 3a shows by and large similar reactivity, but only after photochemical excitation. The derivative 3b inserts into the C-H bonds of hydrocarbon solvents in high yields and thus allows the formation of primary amines, secondary amines, or amides from "unreactive" hydrocarbons. It can also be used for generation of methylamine or methylamide from methane in the gas phase at room temperature. Remaining challenges in the chemistry of borylnitrenes are briefly summarized.

Investigation into the Heat of Hydration and Alkali Silica Reactivity of Sustainable Ultrahigh Strength Concrete with Foundry Sand

Directory of Open Access Journals (Sweden)

Federico Aguayo

2017-01-01

Full Text Available This study presents the hydration reactivity and alkali silica reaction (ASR of ultrahigh strength concrete (UHSC that has been made more sustainable by using spent foundry sand. Spent foundry sand not only is sustainable but has supplementary cementitious material (SCM characteristics. Two series of UHSC mixtures were prepared using a nonreactive and reactive sand (in terms of ASR to investigate both the impact of a more reactive aggregate and the use of spent foundry sand. Conduction calorimetry was used to monitor the heat of hydration maintained under isothermal conditions, while ASR was investigated using the accelerated mortar bar test (AMBT. Additionally, the compressive strengths were measured for both series of mixtures at 7, 14, and 28 days to confirm high strength requirements. The compressive strengths ranged from 85 MPa (12,345 psi to 181.78 MPa (26,365 psi. This result demonstrates that a UHSC mixture was produced. The calorimetry results revealed a slight acceleration in the heat of hydration flow curve compared to the control from both aggregates indicating increased hydration reactivity from the addition of foundry waste. The combination of foundry sand and reactive sand was found to increase ASR reactivity with increasing additions of foundry sand up to 30% replacement.

Tuning silver ion release properties in reactively sputtered Ag/TiOx nanocomposites

Science.gov (United States)

Xiong, J.; Ghori, M. Z.; Henkel, B.; Strunskus, T.; Schürmann, U.; Deng, M.; Kienle, L.; Faupel, F.

2017-07-01

Silver/titania nanocomposites with strong bactericidal effects and good biocompatibility/environmental safety show a high potential for antibacterial applications. Tailoring the silver ion release is thus highly promising to optimize the antibacterial properties of such coatings and to preserve biocompatibility. Reactive sputtering is a fast and versatile method for the preparation of such Ag/TiOx nanocomposites coatings. The present work is concerned with the influence of sputter parameters on the surface morphology and silver ion release properties of reactively sputtered Ag/TiOx nanocomposites coatings showing a silver nanoparticle size distribution in the range from 1 to 20 nm. It is shown that the silver ion release rate strongly depends on the total pressure: the coatings prepared at lower pressure present a lower but long-lasting release behavior. The much denser structure produced under these conditions reduces the transport of water molecules into the coating. In addition, the influence of microstructure and thickness of titanium oxide barriers on the silver ion release were investigated intensively. Moreover, for the coatings prepared at high total pressure, it was demonstrated that stable and long-lasting silver release can be achieved by depositing a barrier with a high rate. Nanocomposites produced under these conditions show well controllable silver ion release properties for applications as antibacterial coatings.

Characterization of coal and char reactivity as a function of burn-off

Energy Technology Data Exchange (ETDEWEB)

Biede, O.; Swane Lund, J. [DTU, Dept. of Energy Engineering (Denmark); Holst Soerensen, L. [Risoe National Lab. (Denmark); Peck, R.E. [Arizona State University (United States)

1996-12-01

Four coal types have been tested under varying burning conditions in three high-temperature experimental facilities: A 1.3 MW test furnace, an entrained flow reactor and a down-fired tube furnace with a flat flame burner have been used to produce char samples. More than one hundred partly burned samples with burn-off from 30% to 99% have been collected from the experimental facilities, and analyzed in a thermogravimetric analyser (TGA) giving, besides the proximate data, a char burning profile of each individual sample, using a linear TGA-temperature ramp of 3 deg. C/minute. The burning profile derived by this procedure agrees well with reactivity profiles derived at a constant temperature. It is shown that small particle burn faster than large particles, and that small particles in general are more reactive than large particles. Particles burn faster when the oxygen partial pressure is increased, and apparently the oxygen partial pressure influences the combustion rate differently for different coal types. Except for one coal type, that apparently behaves differently in different burning environments, the ranking with respect to reactivity among the coals remains consistent at both high and at low temperatures. It is further shown how samples from one coal type varies more in behavior than samples from the other coal types, indicating a larger inhomogeneity of this coal. In general the reactivity of collected samples decrease with high-temperature burn-off. (au) 20 refs.

The influence of petrography, mineralogy and chemistry on burnability and reactivity of quicklime produced in Twin Shaft Regenerative (TSR) kilns from Neoarchean limestone (Transvaal Supergroup, South Africa)

Science.gov (United States)

Vola, Gabriele; Sarandrea, Luca; Della Porta, Giovanna; Cavallo, Alessandro; Jadoul, Flavio; Cruciani, Giuseppe

2017-12-01

This study evaluates the influence of chemical, mineralogical and petrographic features of the Neoarchean limestone from the Ouplaas Mine (Griqualand West, South Africa) on its burnability and quicklime reactivity, considering the main use as raw material for high-grade lime production in twin shaft regenerative (TSR) kilns. This limestone consists of laminated clotted peloidal micrite and fenestrate microbial boundstone with herringbone calcite and organic carbon (kerogen) within stylolites. Diagenetic modifications include hypidiotopic dolomite, micrite to microsparite recrystallization, stylolites, poikilotopic calcite, chert and saddle dolomite replacements. Burning and technical tests widely attest that the Neoarchean limestone is sensitive to high temperature, showing an unusual and drastically pronounced sintering or overburning tendency. The slaking reactivity, according to EN 459-2 is high for lime burnt at 1050 °C, but rapidly decreases for lime burnt at 1150 °C. The predominant micritic microbial textures, coupled with the organic carbon, are key-factors influencing the low burnability and the high sintering tendency. The presence of burial cementation, especially poikilotopic calcite, seems to promote higher burnability, either in terms of starting calcination temperature, or in terms of higher carbonate dissociation rate. In fact, the highest calcination velocity determined by thermal analysis is consistent with the highest slaking reactivity of the lower stratum of the quarry, enriched in poikilotopic calcite. Secondly, locally concentered dolomitic marly limestones, and sporadic back shales negatively affects the quicklime reactivity, as well. This study confirms that a multidisciplinary analytical approach is essential for selecting the best raw mix for achieving the highest lime reactivity in TSR kilns.

Studies on unusually reactive metal powders. Preparation of new organometallic and organic compounds including potential new catalysts. Final report, July 1, 1980-December 31, 1984

International Nuclear Information System (INIS)

Rieke, R.D.

1985-06-01

This research project was involved with the preparation and study of highly reactive metal powders prepared by the reduction of metal salts with alkali metals. Studies concentrated on nickel, copper, cadmium, uranium, iron, and magnesium. The nickel powders have been found to react rapidly with benzylic halides, and the resulting organonickel complexes yield dibenzyl. Aryl halides react rapidly with the nickel powders to produce biaryl compounds in high yields. Benzylic halides react with the nickel powders in the presence of acylhalides to produce benzyl ketones in high yields. Reactions of ROCOCOC1 and benzylic halides with nickel powders yield benzyl ketones. These reactions proceed with a wide variety of substituents on the phenyl ring of the benzylic halides. Highly reactive uranium has been prepared, and found to react with a variety of oxygen containing substrates, such as nitrobenzene to yield azo benzene. Highly reactive magnesium has opened up a totally new area of low temperature Grignard chemistry. The preparation of highly reactive copper has allowed the direct preparation of organocopper species directly from organic halides. 16 refs., 6 tabs

Subsurface Transport Over Reactive Multiphases (STORM): A general, coupled, nonisothermal multiphase flow, reactive transport, and porous medium alteration simulator, Version 2 user's guide

International Nuclear Information System (INIS)

Bacon, D.H.; White, M.D.; McGrail, B.P.

2000-01-01

The Hanford Site, in southeastern Washington State, has been used extensively to produce nuclear materials for the US strategic defense arsenal by the Department of Energy (DOE) and its predecessors, the US Atomic Energy Commission and the US Energy Research and Development Administration. A large inventory of radioactive and mixed waste has accumulated in 177 buried single- and double shell tanks. Liquid waste recovered from the tanks will be pretreated to separate the low-activity fraction from the high-level and transuranic wastes. Vitrification is the leading option for immobilization of these wastes, expected to produce approximately 550,000 metric tons of Low Activity Waste (LAW) glass. This total tonnage, based on nominal Na 2 O oxide loading of 20% by weight, is destined for disposal in a near-surface facility. Before disposal of the immobilized waste can proceed, the DOE must approve a performance assessment, a document that described the impacts, if any, of the disposal facility on public health and environmental resources. Studies have shown that release rates of radionuclides from the glass waste form by reaction with water determine the impacts of the disposal action more than any other independent parameter. This report describes the latest accomplishments in the development of a computational tool, Subsurface Transport Over Reactive Multiphases (STORM), Version 2, a general, coupled non-isothermal multiphase flow and reactive transport simulator. The underlying mathematics in STORM describe the rate of change of the solute concentrations of pore water in a variably saturated, non-isothermal porous medium, and the alteration of waste forms, packaging materials, backfill, and host rocks

Increased ghrelin but low ghrelin-reactive immunoglobulins in a rat model of methotrexate chemotherapy-induced anorexia

Directory of Open Access Journals (Sweden)

Marie François

2016-07-01

Full Text Available Background and aims: Cancer chemotherapy is commonly accompanied by mucositis, anorexia, weight loss and anxiety independently from cancer-induced anorexia-cachexia, further aggravating clinical outcome. Ghrelin is a peptide hormone produced in gastric mucosa that reaches the brain to stimulate appetite. In plasma, ghrelin is protected from degradation by ghrelin-reactive immunoglobulins (Ig. To analyze possible involvement of ghrelin in the chemotherapy-induced anorexia and anxiety, gastric ghrelin expression, plasma levels of ghrelin and ghrelin-reactive IgG were studied in rats treated with methotrexate (MTX.Methods: Rats received MTX (2.5 mg/kg, S.C. for three consecutive days and were killed 3 days later, at the peak of anorexia and weight loss. Control rats received phosphate-buffered saline. Preproghrelin mRNA expression in the stomach was analyzed by in situ hybridization. Plasma levels of ghrelin and ghrelin-reactive IgG were measured by immunoenzymatic assays and IgG affinity kinetics by surface plasmon resonance. Anxiety- and depression-like behaviors in MTX-treated anorectic and in control rats were evaluated in the elevated plus-maze and the forced-swim test, respectively.Results: In MTX-treated anorectic rats the number of preproghrelin mRNA-producing cells was found increased (by 51.3%, p<0.001 as well were plasma concentrations of both ghrelin and des-acyl-ghrelin (by 70.4%, p<0.05 and 98.3%, p<0.01, respectively. In contrast, plasma levels of total IgG reactive with ghrelin and des-acyl-ghrelin were drastically decreased (by 87.2% and 88.4%, respectively, both p<0.001, and affinity kinetics of these IgG were characterized by increased small and big Kd, respectively. MTX-treated rats displayed increased anxiety- but not depression-like behavior.Conclusion: MTX-induced anorexia, weight loss and anxiety are accompanied by increased ghrelin production and by a decrease of ghrelin-reactive IgG levels and affinity binding properties

H3N2 influenza infection elicits more cross-reactive and less clonally expanded anti-hemagglutinin antibodies than influenza vaccination.

Directory of Open Access Journals (Sweden)

M Anthony Moody

Full Text Available BACKGROUND: During the recent H1N1 influenza pandemic, excess morbidity and mortality was seen in young but not older adults suggesting that prior infection with influenza strains may have protected older subjects. In contrast, a history of recent seasonal trivalent vaccine in younger adults was not associated with protection. METHODS AND FINDINGS: To study hemagglutinin (HA antibody responses in influenza immunization and infection, we have studied the day 7 plasma cell repertoires of subjects immunized with seasonal trivalent inactivated influenza vaccine (TIV and compared them to the plasma cell repertoires of subjects experimentally infected (EI with influenza H3N2 A/Wisconsin/67/2005. The majority of circulating plasma cells after TIV produced influenza-specific antibodies, while most plasma cells after EI produced antibodies that did not react with influenza HA. While anti-HA antibodies from TIV subjects were primarily reactive with single or few HA strains, anti-HA antibodies from EI subjects were isolated that reacted with multiple HA strains. Plasma cell-derived anti-HA antibodies from TIV subjects showed more evidence of clonal expansion compared with antibodies from EI subjects. From an H3N2-infected subject, we isolated a 4-member clonal lineage of broadly cross-reactive antibodies that bound to multiple HA subtypes and neutralized both H1N1 and H3N2 viruses. This broad reactivity was not detected in post-infection plasma suggesting this broadly reactive clonal lineage was not immunodominant in this subject. CONCLUSION: The presence of broadly reactive subdominant antibody responses in some EI subjects suggests that improved vaccine designs that make broadly reactive antibody responses immunodominant could protect against novel influenza strains.

Fast screening of analytes for chemical reactions by reactive low-temperature plasma ionization mass spectrometry.

Science.gov (United States)

Zhang, Wei; Huang, Guangming

2015-11-15

Approaches for analyte screening have been used to aid in the fine-tuning of chemical reactions. Herein, we present a simple and straightforward analyte screening method for chemical reactions via reactive low-temperature plasma ionization mass spectrometry (reactive LTP-MS). Solution-phase reagents deposited on sample substrates were desorbed into the vapor phase by action of the LTP and by thermal desorption. Treated with LTP, both reagents reacted through a vapor phase ion/molecule reaction to generate the product. Finally, protonated reagents and products were identified by LTP-MS. Reaction products from imine formation reaction, Eschweiler-Clarke methylation and the Eberlin reaction were detected via reactive LTP-MS. Products from the imine formation reaction with reagents substituted with different functional groups (26 out of 28 trials) were successfully screened in a time of 30 s each. Besides, two short-lived reactive intermediates of Eschweiler-Clarke methylation were also detected. LTP in this study serves both as an ambient ionization source for analyte identification (including reagents, intermediates and products) and as a means to produce reagent ions to assist gas-phase ion/molecule reactions. The present reactive LTP-MS method enables fast screening for several analytes from several chemical reactions, which possesses good reagent compatibility and the potential to perform high-throughput analyte screening. In addition, with the detection of various reactive intermediates (intermediates I and II of Eschweiler-Clarke methylation), the present method would also contribute to revealing and elucidating reaction mechanisms. Copyright © 2015 John Wiley & Sons, Ltd.

Titanium carbide coatings on molybdenum by means of reactive sputtering and electron beam techniques

International Nuclear Information System (INIS)

Obata, T.; Aida, H.; Hirohata, Y.; Mohri, M.; Yamashina, T.

1982-01-01

This study is an experimental investigation of TiC coatings on Mo substrate by means of a reactive r.f. sputtering in the presence of CH 4 and a chemical reaction with interdiffusion in the sandwich structure of Ti/C/Mo by electron beam evaporation and heating. Using the reactive sputtering method, a homogeneous TiC coating with stoichiometric composition and good adhesion could be produced in the conditions of the partial pressure range of CH 4 , 2 approx. equal to 5 x 10 -4 Torr (total pressure, Psub(Ar) + Psub(CH) 4 = 5.6 x 10 -2 Torr) at 300 0 C (substrate). By using the electron beams, successively evaporated carbon and Ti on a Mo substrate was heated to 700 0 C to form a TiC surface layer on the top which then remained stable during further heating to 1000 0 C. Godd adhesion was brought about by interdiffusion to produce Mo 2 C layer between TiC layer and Mo substrate. It was also found that further heating of the coating layers subsequent to Ti evaporation on the TiC layer produced thicker TiC layer due to a chemical reaction between Ti and inner carbon layers. This could be a promising method of in situ replenishment for TiC coatings on the first wall and the limiter materials. (orig.)

Reactivity of hydrogen contained in Raney nickel for ethylene hydrogenation studied by means of a tritium tracer

International Nuclear Information System (INIS)

Miyatani, Daisaku; Takeuchi, Toyosaburo.

1979-01-01

Reactivity of hydrogen contained in Raney nickel with ethylene was studied by using a tritium tracer. Hydrogen in Raney nickel was previously labeled with tritium and distinguished from hydrogen introduced during the hydrogenation reaction. The reactivity of the contained hydrogen was determined by measurement of the radioactivity of ethane produced in the hydrogenation. Ethylene reacted with hydrogen in Raney nickel for no supply of hydrogen during the hydrogenation. However, when ethylene was hydrogenated by both hydrogen in Raney nickel and introduced hydrogen, over 99% of the ethylene reacted with the introduced hydrogen and hardly reacted with the contained hydrogen. (author)

Reactive oxygen species formation during tetanic contractions in single isolated Xenopus myofibers

OpenAIRE

Zuo, Li; Nogueira, Leonardo; Hogan, Michael C.

2011-01-01

Contracting skeletal muscle produces reactive oxygen species (ROS) that have been shown to affect muscle function and adaptation. However, real-time measurement of ROS in contracting myofibers has proven to be difficult. We used amphibian (Xenopus laevis) muscle to test the hypothesis that ROS are formed during contractile activity in isolated single skeletal muscle fibers and that this contraction-induced ROS formation affects fatigue development. Single myofibers were loaded with 5 μM dihyd...

Evaluation of different glycoforms of honeybee venom major allergen phospholipase A2 (Api m 1) produced in insect cells

DEFF Research Database (Denmark)

Blank, Simon; Seismann, Henning; Plum, Melanie

2011-01-01

Allergic reactions to hymenoptera stings are one of the major reasons for IgE-mediated anaphylaxis. However, proper diagnosis using venom extracts is severely affected by molecular cross-reactivity. In this study recombinant honeybee venom major allergen phospholipase A2 (Api m 1) was produced......-derived recombinant Api m 1 with defined CCD phenotypes might provide further insights into hymenoptera venom IgE reactivities and contribute to an improved diagnosis of hymenoptera venom allergy....

Neighborhood disadvantage and adolescent stress reactivity

Directory of Open Access Journals (Sweden)

Daniel A. Hackman

2012-10-01

Full Text Available Lower socioeconomic status (SES is associated with higher levels of life stress, which in turn affect stress physiology. SES is related to basal cortisol and diurnal change, but it is not clear if SES is associated with cortisol reactivity to stress. To address this question, we examined the relationship between two indices of SES, parental education and concentrated neighborhood disadvantage, and the cortisol reactivity of African-American adolescents to a modified version of the Trier Social Stress Test. We found that concentrated disadvantage was associated with cortisol reactivity and this relationship was moderated by gender, such that higher concentrated disadvantage predicted higher cortisol reactivity and steeper recovery in boys but not in girls. Parental education, alone or as moderated by gender, did not predict reactivity or recovery, while neither education nor concentrated disadvantage predicted estimates of baseline cortisol. This finding is consistent with animal literature showing differential vulnerability, by gender, to the effects of adverse early experience on stress regulation and the differential effects of neighborhood disadvantage in adolescent males and females. This suggests that the mechanisms underlying SES differences in brain development and particularly reactivity to environmental stressors may vary across genders.

Control of Reactive Species Generated by Low-frequency Biased Nanosecond Pulse Discharge in Atmospheric Pressure Plasma Effluent

Science.gov (United States)

Takashima, Keisuke; Kaneko, Toshiro

2016-09-01

The control of hydroxyl radical and the other gas phase species generation in the ejected gas through air plasma (air plasma effluent) has been experimentally studied, which is a key to extend the range of plasma treatment. Nanosecond pulse discharge is known to produce high reduced electric field (E/N) discharge that leads to efficient generation of the reactive species than conventional low frequency discharge, while the charge-voltage cycle in the low frequency discharge is known to be well-controlled. In this study, the nanosecond pulse discharge biased with AC low frequency high voltage is used to take advantages of these discharges, which allows us to modulate the reactive species composition in the air plasma effluent. The utilization of the gas-liquid interface and the liquid phase chemical reactions between the modulated long-lived reactive species delivered from the air plasma effluent could realize efficient liquid phase chemical reactions leading to short-lived reactive species production far from the air plasma, which is crucial for some plasma agricultural applications.

High Contrast Internal and External Coronagraph Masks Produced by Various Techniques

Science.gov (United States)

Balasubramanian, Kunjithapatha; Wilson, Daniel; White, Victor; Muller, Richard; Dickie, Matthew; Yee, Karl; Ruiz, Ronald; Shaklan, Stuart; Cady, Eric; Kern, Brian;

Psychophysiology of proactive and reactive relational aggression.

Science.gov (United States)

Murray-Close, Dianna; Holterman, Leigh Ann; Breslend, Nicole L; Sullivan, Alexandra

2017-12-01

This study investigated the joint effects of parasympathetic and sympathetic nervous system reactivity to social and non-social stressors on proactive (i.e., goal-directed, unemotional) and reactive (i.e., emotional, impulsive) functions of relational aggression. Two hundred and forty-seven (M age =18.77years) participants completed a series of stressor tasks while their sympathetic arousal (i.e., skin conductance) and parasympathetic arousal (i.e., respiratory sinus arrhythmia) were assessed. Participants also provided self-reports of their aggressive behavior. In the standardized social stressor only, physiological reactivity was related to aggression, such that respiratory sinus arrhythmia augmentation predicted proactive relational aggression whereas heightened skin conductance reactivity predicted reactive relational aggression. Finally, in the context of low skin conductance reactivity, respiratory sinus arrhythmia augmentation was related to heightened proactive and reactive aggression, whereas respiratory sinus arrhythmia withdrawal was protective. Results suggest that the benefits hypothesized to accompany respiratory sinus arrhythmia withdrawal may only occur among individuals with low "fight or flight" stress responses. Findings extend research on the physiological indicators of aggression to relational aggression, and highlight the importance of assessing functions of aggression, as well as physiological reactivity to multiple stressors. Copyright © 2017 Elsevier B.V. All rights reserved.

Two-frequency, one-detector reactivity system (TFODRS)

International Nuclear Information System (INIS)

Sachs, R.D.; Woodall, D.M.

1985-01-01

A two-frequency, one-detector reactivity system (TFODRS) was experimentally verified on the University of New Mexico (UNM) AGN-201M thermal reactor. That system was used to obtain the absolute steady-state reactivity and to demonstrate the feasibility of acquiring the transient reactivity. A detailed description of TFODRS hardware and software is given in this paper. The TFODRS obtains the absolute and net reactivity by computing the frequency spectrum of the reactor neutron-detector signal. The ratio of the high-frequency to the low-frequency components about an empirical break point is used to determine the reactivity. The TFODRS was successfully used to measure a known AGN-201M steady-state reactivity, with a relative error of 18%. TFODRS transient curves as a function of reactivity were shown to be different from the steady-state curves. The transient curves appear to be a function of the rate of reactivity insertion. The authors speculate that a modified TFODRS, using state-of-the-art microprocessors, could be used for fast reactors. The TFODRS is not presently a practicable reactimeter. However, with more research and development, it is felt it could be used in near-term nuclear industry applications, such as monitoring fuel storage pools

Reactive agents and perceptual ambiguity

NARCIS (Netherlands)

Dartel, M. van; Sprinkhuizen-Kuyper, I.G.; Postma, E.O.; Herik, H.J. van den

2005-01-01

Reactive agents are generally believed to be incapable of coping with perceptual ambiguity (i.e., identical sensory states that require different responses). However, a recent finding suggests that reactive agents can cope with perceptual ambiguity in a simple model (Nolfi, 2002). This paper

Prediction of BP Reactivity to Talking Using Hybrid Soft Computing Approaches

Directory of Open Access Journals (Sweden)

Gurmanik Kaur

2014-01-01

Full Text Available High blood pressure (BP is associated with an increased risk of cardiovascular diseases. Therefore, optimal precision in measurement of BP is appropriate in clinical and research studies. In this work, anthropometric characteristics including age, height, weight, body mass index (BMI, and arm circumference (AC were used as independent predictor variables for the prediction of BP reactivity to talking. Principal component analysis (PCA was fused with artificial neural network (ANN, adaptive neurofuzzy inference system (ANFIS, and least square-support vector machine (LS-SVM model to remove the multicollinearity effect among anthropometric predictor variables. The statistical tests in terms of coefficient of determination (R2, root mean square error (RMSE, and mean absolute percentage error (MAPE revealed that PCA based LS-SVM (PCA-LS-SVM model produced a more efficient prediction of BP reactivity as compared to other models. This assessment presents the importance and advantages posed by PCA fused prediction models for prediction of biological variables.

Prediction of BP reactivity to talking using hybrid soft computing approaches.

Science.gov (United States)

Kaur, Gurmanik; Arora, Ajat Shatru; Jain, Vijender Kumar

2014-01-01

High blood pressure (BP) is associated with an increased risk of cardiovascular diseases. Therefore, optimal precision in measurement of BP is appropriate in clinical and research studies. In this work, anthropometric characteristics including age, height, weight, body mass index (BMI), and arm circumference (AC) were used as independent predictor variables for the prediction of BP reactivity to talking. Principal component analysis (PCA) was fused with artificial neural network (ANN), adaptive neurofuzzy inference system (ANFIS), and least square-support vector machine (LS-SVM) model to remove the multicollinearity effect among anthropometric predictor variables. The statistical tests in terms of coefficient of determination (R (2)), root mean square error (RMSE), and mean absolute percentage error (MAPE) revealed that PCA based LS-SVM (PCA-LS-SVM) model produced a more efficient prediction of BP reactivity as compared to other models. This assessment presents the importance and advantages posed by PCA fused prediction models for prediction of biological variables.

[Reactivation of parvovirus B19 infection in an HIV-infected woman].

Science.gov (United States)

Sterpu, R; Ichou, H; Mahé, I; Mortier, E

2014-06-01

Infection by human parvovirus B19 (erythrovirus B19) is common and usually asymptomatic during childhood conferring lasting protection against a new infection. Parvovirus B19 infection may cause erythema infectiosum (5th disease) and aplastic crisis. Secondary symptomatic parvovirus B19 infection in the same patient is rare and its physiopathology is not always clear. A 48-year-old HIV-infected female patient presented within 5 years two acute episodes of parvovirus B19 infection although her CD4 cells count was above 500/mm(3). Absence of specific antibodies production after the first episode and persisting parvovirus viremia suggested viral reactivation rather than re-infection. During the second episode, specific antibodies were produced. Similarly to most DNA viruses, parvovirus B19 reactivation is possible in HIV-infected patients while effectively treated by antiretroviral therapy. Copyright © 2013 Société nationale française de médecine interne (SNFMI). Published by Elsevier SAS. All rights reserved.

Reactive Membrane Barriers for Containment of Subsurface Contamination

Energy Technology Data Exchange (ETDEWEB)

William A. Arnold; Edward L. Cussler

2007-02-26

The overall goal of this project was to develop reactive membrane barriers--a new and flexible technique to contain and stabilize subsurface contaminants. Polymer membranes will leak once a contaminant is able to diffuse through the membrane. By incorporating a reactive material in the polymer, however, the contaminant is degraded or immobilized within the membrane. These processes increase the time for contaminants to breakthrough the barrier (i.e. the lag time) and can dramatically extend barrier lifetimes. In this work, reactive barrier membranes containing zero-valent iron (Fe{sup 0}) or crystalline silicotitanate (CST) were developed to prevent the migration of chlorinated solvents and cesium-137, respectively. These studies were complemented by the development of models quantifying the leakage/kill time of reactive membranes and describing the behavior of products produced via the reactions within the membranes. First, poly(vinyl alcohol) (PVA) membranes containing Fe{sup 0} and CST were prepared and tested. Although PVA is not useful in practical applications, it allows experiments to be performed rapidly and the results to be compared to theory. For copper ions (Cu{sup 2+}) and carbon tetrachloride, the barrier was effective, increasing the time to breakthrough over 300 times. Even better performance was expected, and the percentage of the iron used in the reaction with the contaminants was determined. For cesium, the CST laden membranes increased lag times more than 30 times, and performed better than theoretical predictions. A modified theory was developed for ion exchangers in reactive membranes to explain this result. With the PVA membranes, the effect of a groundwater matrix on barrier performance was tested. Using Hanford groundwater, the performance of Fe{sup 0} barriers decreased compared to solutions containing a pH buffer and high levels of chloride (both of which promote iron reactivity). For the CST bearing membrane, performance improved by a

Reactive Membrane Barriers for Containment of Subsurface Contamination

International Nuclear Information System (INIS)

William A. Arnold; Edward L. Cussler

2007-01-01

The overall goal of this project was to develop reactive membrane barriers--a new and flexible technique to contain and stabilize subsurface contaminants. Polymer membranes will leak once a contaminant is able to diffuse through the membrane. By incorporating a reactive material in the polymer, however, the contaminant is degraded or immobilized within the membrane. These processes increase the time for contaminants to breakthrough the barrier (i.e. the lag time) and can dramatically extend barrier lifetimes. In this work, reactive barrier membranes containing zero-valent iron (Fe 0 ) or crystalline silicotitanate (CST) were developed to prevent the migration of chlorinated solvents and cesium-137, respectively. These studies were complemented by the development of models quantifying the leakage/kill time of reactive membranes and describing the behavior of products produced via the reactions within the membranes. First, poly(vinyl alcohol) (PVA) membranes containing Fe 0 and CST were prepared and tested. Although PVA is not useful in practical applications, it allows experiments to be performed rapidly and the results to be compared to theory. For copper ions (Cu 2+ ) and carbon tetrachloride, the barrier was effective, increasing the time to breakthrough over 300 times. Even better performance was expected, and the percentage of the iron used in the reaction with the contaminants was determined. For cesium, the CST laden membranes increased lag times more than 30 times, and performed better than theoretical predictions. A modified theory was developed for ion exchangers in reactive membranes to explain this result. With the PVA membranes, the effect of a groundwater matrix on barrier performance was tested. Using Hanford groundwater, the performance of Fe 0 barriers decreased compared to solutions containing a pH buffer and high levels of chloride (both of which promote iron reactivity). For the CST bearing membrane, performance improved by a factor of three when

Reactive Systems

DEFF Research Database (Denmark)

Aceto, Luca; Ingolfsdottir, Anna; Larsen, Kim Guldstrand

A reactive system comprises networks of computing components, achieving their goals through interaction among themselves and their environment. Thus even relatively small systems may exhibit unexpectedly complex behaviours. As moreover reactive systems are often used in safety critical systems......, the need for mathematically based formal methodology is increasingly important. There are many books that look at particular methodologies for such systems. This book offers a more balanced introduction for graduate students and describes the various approaches, their strengths and weaknesses, and when...... they are best used. Milner's CCS and its operational semantics are introduced, together with the notions of behavioural equivalences based on bisimulation techniques and with recursive extensions of Hennessy-Milner logic. In the second part of the book, the presented theories are extended to take timing issues...

Contribution of reactive oxygen species to the pathogenesis of pulmonary arterial hypertension

Science.gov (United States)

Naik, Jay S.; Weise-Cross, Laura; Detweiler, Neil D.; Herbert, Lindsay M.; Yellowhair, Tracylyn R.; Resta, Thomas C.

2017-01-01

Pulmonary arterial hypertension is associated with a decreased antioxidant capacity. However, neither the contribution of reactive oxygen species to pulmonary vasoconstrictor sensitivity, nor the therapeutic efficacy of antioxidant strategies in this setting are known. We hypothesized that reactive oxygen species play a central role in mediating both vasoconstrictor and arterial remodeling components of severe pulmonary arterial hypertension. We examined the effect of the chemical antioxidant, TEMPOL, on right ventricular systolic pressure, vascular remodeling, and enhanced vasoconstrictor reactivity in both chronic hypoxia and hypoxia/SU5416 rat models of pulmonary hypertension. SU5416 is a vascular endothelial growth factor receptor antagonist and the combination of chronic hypoxia/SU5416 produces a model of severe pulmonary arterial hypertension with vascular plexiform lesions/fibrosis that is not present with chronic hypoxia alone. The major findings from this study are: 1) compared to hypoxia alone, hypoxia/SU5416 exposure caused more severe pulmonary hypertension, right ventricular hypertrophy, adventitial lesion formation, and greater vasoconstrictor sensitivity through a superoxide and Rho kinase-dependent Ca2+ sensitization mechanism. 2) Chronic hypoxia increased medial muscularization and superoxide levels, however there was no effect of SU5416 to augment these responses. 3) Treatment with TEMPOL decreased right ventricular systolic pressure in both hypoxia and hypoxia/SU5416 groups. 4) This effect of TEMPOL was associated with normalization of vasoconstrictor responses, but not arterial remodeling. Rather, medial hypertrophy and adventitial fibrotic lesion formation were more pronounced following chronic TEMPOL treatment in hypoxia/SU5416 rats. Our findings support a major role for reactive oxygen species in mediating enhanced vasoconstrictor reactivity and pulmonary hypertension in both chronic hypoxia and hypoxia/SU5416 rat models, despite a

Emotional reactivity: Beware its involvement in traffic accidents.

Science.gov (United States)

M'bailara, Katia; Atzeni, Thierry; Contrand, Benjamin; Derguy, Cyrielle; Bouvard, Manuel-Pierre; Lagarde, Emmanuel; Galéra, Cédric

2018-04-01

Reducing risk attributable to traffic accidents is a public health challenge. Research into risk factors in the area is now moving towards identification of the psychological factors involved, particularly emotional states. The aim of this study was to evaluate the link between emotional reactivity and responsibility in road traffic accidents. We hypothesized that the more one's emotional reactivity is disturbed, the greater the likelihood of being responsible for a traffic accident. This case-control study was based on a sample of 955 drivers injured in a motor vehicle crash. Responsibility levels were determined with a standardized method adapted from the quantitative Robertson and Drummer crash responsibility instrument. Emotional reactivity was assessed with the MATHYS. Hierarchical cluster analysis discriminated four distinctive driver's emotional reactivity profiles: basic emotional reactivity (54%), mild emotional hyper-reactivity (29%), emotional hyper-reactivity (11%) and emotional hypo-reactivity (6%). Drivers who demonstrated emotional hypo-reactivity had a 2.3-fold greater risk of being responsible for a traffic accident than those with basic emotional reactivity. Drivers' responsibility in traffic accidents depends on their emotional status. The latter can change the ability of drivers, modifying their behavior and thus increasing their propensity to exhibit risk behavior and to cause traffic accidents. Copyright © 2017 Elsevier B.V. All rights reserved.

Quantification of Hydroxyl Radical reactivity in the urban environment using the Comparative Reactivity Method (CRM)

Science.gov (United States)

Panchal, Rikesh; Monks, Paul

2015-04-01

Hydroxyl (OH) radicals play an important role in 'cleansing' the atmosphere of many pollutants such as, NOx, CH4 and various VOCs, through oxidation. To measure the reactivity of OH, both the sinks and sources of OH need to be quantified, and currently the overall sinks of OH seem not to be fully constrained. In order to measure the total rate loss of OH in an ambient air sample, all OH reactive species must be considered and their concentrations and reaction rate coefficients with OH known. Using the method pioneered by Sinha and Williams at the Max Plank Institute Mainz, the Comparative Reactivity Method (CRM) which directly quantifies total OH reactivity in ambient air without the need to consider the concentrations of individual species within the sample that can react with OH, has been developed and applied in a urban setting. The CRM measures the concentration of a reactive species that is present only in low concentrations in ambient air, in this case pyrrole, flowing through a reaction vessel and detected using Proton Transfer Reaction - Mass Spectrometry (PTR-MS). The poster will show a newly developed and tested PTR-TOF-MS system for CRM. The correction regime will be detailed to account for the influence of the varying humidity between ambient air and clean air on the pyrrole signal. Further, examination of the sensitivity dependence of the PTR-MS as a function of relative humidity and H3O+(H2O) (m/z=37) cluster ion allows the correction for the humidity variation, between the clean humid air entering the reaction vessel and ambient air will be shown. NO, present within ambient air, is also a potential interference and can cause recycling of OH, resulting in an overestimation of OH reactivity. Tests have been conducted on the effects of varying NO concentrations on OH reactivity and a correction factor determined for application to data when sampling ambient air. Finally, field tests in the urban environment at the University of Leicester will be shown

Substation Reactive Power Regulation Strategy

Science.gov (United States)

Zhang, Junfeng; Zhang, Chunwang; Ma, Daqing

2018-01-01

With the increasing requirements on the power supply quality and reliability of distribution network, voltage and reactive power regulation of substations has become one of the indispensable ways to ensure voltage quality and reactive power balance and to improve the economy and reliability of distribution network. Therefore, it is a general concern of the current power workers and operators that what kind of flexible and effective control method should be used to adjust the on-load tap-changer (OLTC) transformer and shunt compensation capacitor in a substation to achieve reactive power balance in situ, improve voltage pass rate, increase power factor and reduce active power loss. In this paper, based on the traditional nine-zone diagram and combining with the characteristics of substation, a fuzzy variable-center nine-zone diagram control method is proposed and used to make a comprehensive regulation of substation voltage and reactive power. Through the calculation and simulation of the example, this method is proved to have satisfactorily reconciled the contradiction between reactive power and voltage in real-time control and achieved the basic goal of real-time control of the substation, providing a reference value to the practical application of the substation real-time control method.

Orifice microreactor for the production of an organic peroxide – non-reactive and reactive characterization

NARCIS (Netherlands)

Illg, T.; Hessel, V.; Löb, P.; Schouten, J.C.

2012-01-01

In this article, the transfer of a two-step, biphasic, and exothermic peroxide synthesis into a microreactor assisted process is discussed as well as the non-reactive and reactive characterization of the developed orifice microreactor. Residence time distribution measurements showed nearly ideal

Reward disrupts reactivated human skill memory.

Science.gov (United States)

Dayan, Eran; Laor-Maayany, Rony; Censor, Nitzan

2016-06-16

Accumulating evidence across species and memory domains shows that when an existing memory is reactivated, it becomes susceptible to modifications. However, the potential role of reward signals in these mechanisms underlying human memory dynamics is unknown. Leaning on a wealth of findings on the role of reward in reinforcing memory, we tested the impact of reinforcing a skill memory trace with monetary reward following memory reactivation, on strengthening of the memory trace. Reinforcing reactivated memories did not strengthen the memory, but rather led to disruption of the memory trace, breaking down the link between memory reactivation and subsequent memory strength. Statistical modeling further revealed a strong mediating role for memory reactivation in linking between memory encoding and subsequent memory strength only when the memory was replayed without reinforcement. We suggest that, rather than reinforcing the existing memory trace, reward creates a competing memory trace, impairing expression of the original reward-free memory. This mechanism sheds light on the processes underlying skill acquisition, having wide translational implications.

Elevated and cross-responsive CD1a-reactive T cells in bee and wasp venom allergic individuals.

Science.gov (United States)

Subramaniam, Sumithra; Aslam, Aamir; Misbah, Siraj A; Salio, Mariolina; Cerundolo, Vincenzo; Moody, D Branch; Ogg, Graham

2016-01-01

The role of CD1a-reactive T cells in human allergic disease is unknown. We have previously shown that circulating CD1a-reactive T cells recognize neolipid antigens generated by bee and wasp venom phospholipase, and here tested the hypothesis that venom-responsive CD1a-reactive T cells associate with venom allergy. Circulating T cells from bee and wasp venom allergic individuals, before and during immunotherapy, were exposed to CD1a-transfected K562 cells in the presence of wasp or bee venom. T-cell response was evaluated based on IFNγ, GM-CSF, and IL-13 cytokine production. Venom allergic individuals showed significantly higher frequencies of IFN-γ, GM-CSF, and IL-13 producing CD1a-reactive T cells responsive to venom and venom-derived phospholipase than healthy individuals. Venom-responsive CD1a-reactive T cells were cross-responsive between wasp and bee suggesting shared pathways of allergenicity. Frequencies of CD1a-reactive T cells were initially induced during subcutaneous immunotherapy, peaking by weeks 5, but then reduced despite escalation of antigen dose. Our current understanding of venom allergy and immunotherapy is largely based on peptide and protein-specific T cell and antibody responses. Here, we show that lipid antigens and CD1a-reactive T cells associate with the allergic response. These data have implications for mechanisms of allergy and approaches to immunotherapy. © 2015 The Authors. European Journal of Immunology published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Models for coolant void reactivity evaluation in Candu Generation II and III+

International Nuclear Information System (INIS)

Popov, Alexi V.; Chambon, Richard P.; Le Tellier, Romain; Marleau, Guy; Hebert, Alain

2008-01-01

In the simulation of large-break loss-of-coolant accidents, homogenised cross-sections from trans- port calculations are used. These are usually computed in single cells or lattices representative for an infinite repeated pattern. Large coolant accidents in Candu, however, usually exhibit a checkerboard pattern of cooled and voided channels represented by lattices. It is reasonable, therefore, that homogenised cross-sections be produced in assemblies of lattices. This allows simulating the checkerboard voiding pat- tern and more realistically reproducing the lattice boundary conditions. The result is better simulation of the accident and more precise evaluation of coolant-void reactivity. For the present study, homogenised cross-sections are generated in a 2x2 heterogeneous assembly of four lattices for Generation II and III+ Candu designs. Results of reactivity calculations with the reactor code are compared to those using the traditional method. The difference is significant for Generation III+ Candu. (authors)

Corrosion resistance of ZrNxOy thin films obtained by rf reactive magnetron sputtering

International Nuclear Information System (INIS)

Ariza, E.; Rocha, L.A.; Vaz, F.; Cunha, L.; Ferreira, S.C.; Carvalho, P.; Rebouta, L.; Alves, E.; Goudeau, Ph.; Riviere, J.P.

2004-01-01

The main aim of this work is the investigation of the corrosion resistance of single layered zirconium oxynitride, ZrN x O y , thin films in artificial sweat solution at ambient temperature. The films were produced by rf reactive magnetron sputtering, using a pure Zr target at a constant temperature of 300 deg. C. Two different sets of samples were produced. In the first set of films, the substrate bias voltage was the main variable, whereas in the second set, the flow rate of reactive gases (oxygen/nitrogen ratio) was varied. The control of the amount of oxygen allowed the film properties to be tailored from those of covalent zirconium nitride to those of the correspondent ionic oxide. The corrosion behaviour was evaluated by potentiodynamic polarization and Electrochemical Impedance Spectroscopy (EIS) tests. The analysis of EIS data provided detailed information of the corrosion processes occurring at the surface of the system throughout the immersion time. The modifications of the coating microstructure and/or chemical composition induced by the variation of the deposition parameters were also evaluated and correlated with the corrosion mechanisms occurring in each system

Effect of exhaust gas recirculation (EGR) and multiple injections on diesel soot nano-structure and reactivity

International Nuclear Information System (INIS)

Rohani, Behzad; Bae, Choongsik

2017-01-01

Highlights: • EGR reduced the nano-structural order, regardless of injection strategy. • EGR reduces both VOF and reactivity, regardless of injection strategy. • Longer dwell time between pilot and main injection increases VOF and reactivity. • With EGR, VOF and reactivity are both reduced and un-affected by injection strategy. • VOF-reactivity correlation (without causality) suggests role of surface roughness. - Abstract: The physio-chemical characteristics of soot particles are of importance with regard to performance of diesel after-treatment systems. In this study, the soot particles generated in a single-cylinder heavy-duty diesel engine are examined in terms of nanostructure, oxidative reactivity and volatile organic fraction (VOF), using thermogravimetric analysis (TGA), X-ray diffraction (XRD), Raman micro-spectroscopy, and high resolution transmission electron microscopy (HRTEM). Five different injection strategies including single injection and multiple injections with various pilot injection amounts and dwell times were tested with and without exhaust gas recirculation (EGR), while combustion phasing, engine speed, and fuel injection quantity was matched for all cases. Results indicate that for the soot produced under EGR condition, nano-structural order (indicated by crystallite size obtained from XRD and AD1/AG resulted from the Raman Analysis) can explain the soot reactivity. However, in the absence of EGR, the reactivity trend cannot be explained by the structural order. It is discussed that a possible reason can be a higher level of in-cylinder oxidation in non-EGR cases (indicated by higher level of surface functional groups) which roughens the soot surface, and enhances the oxidation by increasing the specific soot surface area. It is also found that in the absence of EGR, different injection strategies impact the soot reactivity and VOF content, which can be explained mainly through the level of charge premixed-ness and the in

Impact of plasma jet vacuum ultraviolet radiation on reactive oxygen species generation in bio-relevant liquids

Energy Technology Data Exchange (ETDEWEB)

Jablonowski, H.; Hammer, M. U.; Reuter, S. [Center for Innovation Competence plasmatis, Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany); Leibniz Institute for Plasma Science and Technology, INP Greifswald e.V. Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany); Bussiahn, R.; Weltmann, K.-D.; Woedtke, Th. von [Leibniz Institute for Plasma Science and Technology, INP Greifswald e.V. Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany)

2015-12-15

Plasma medicine utilizes the combined interaction of plasma produced reactive components. These are reactive atoms, molecules, ions, metastable species, and radiation. Here, ultraviolet (UV, 100–400 nm) and, in particular, vacuum ultraviolet (VUV, 10–200 nm) radiation generated by an atmospheric pressure argon plasma jet were investigated regarding plasma emission, absorption in a humidified atmosphere and in solutions relevant for plasma medicine. The energy absorption was obtained for simple solutions like distilled water (dH{sub 2}O) or ultrapure water and sodium chloride (NaCl) solution as well as for more complex ones, for example, Rosewell Park Memorial Institute (RPMI 1640) cell culture media. As moderate stable reactive oxygen species, hydrogen peroxide (H{sub 2}O{sub 2}) was studied. Highly reactive oxygen radicals, namely, superoxide anion (O{sub 2}{sup •−}) and hydroxyl radicals ({sup •}OH), were investigated by the use of electron paramagnetic resonance spectroscopy. All species amounts were detected for three different treatment cases: Plasma jet generated VUV and UV radiation, plasma jet generated UV radiation without VUV part, and complete plasma jet including all reactive components additionally to VUV and UV radiation. It was found that a considerable amount of radicals are generated by the plasma generated photoemission. From the experiments, estimation on the low hazard potential of plasma generated VUV radiation is discussed.

YBCO coated conductors by reactive thermal co-evaporation

Energy Technology Data Exchange (ETDEWEB)

Schmatz, U.; Hoffmann, Ch.; Bauer, M.; Metzger, R.; Berberich, P.; Kinder, H. [Technische Univ. Muenchen, Garching (Germany). Physik-Department

2001-12-01

Coated tape conductors of YBCO require a deposition process allowing to obtain a high volume growth rate in order to produce long lengths of tape in a reasonable amount of time. We present our tape coating system where 15 parallel loops of travelling tape of 1 cm width can be coated simultaneously by reactive thermal co-evaporation. For high critical current densities, in-plane alignment of the YBCO film is necessary. Inclined substrate deposition (ISD) is a technique that allows to deposit in-plane oriented buffer layers suitable for YBCO growth at high deposition rates. We present results obtained for YBCO films grown on MgO-ISD buffer layers deposited by e-gun evaporation onto metallic tape substrates. (orig.)

Analysis on void reactivity of DCA lattice

International Nuclear Information System (INIS)

Min, B. J.; Noh, K. H.; Choi, H. B.; Yang, M. K.

2001-01-01

In case of loss of coolant accident, the void reactivity of CANDU fuel provides the positive reactivity and increases the reactor power rapidly. Therefore, it is required to secure credibility of the void reactivity for the design and analysis of reactor, which motivated a study to assess the measurement data of void reactivity. The assessment of lattice code was performed with the experimental data of void reactivity at 30, 70, 87 and 100% of void fractions. The infinite multiplication factors increased in four types of fuels as the void fractions of them grow. The infinite multiplication factors of uranium fuels are almost within 1%, but those of Pu fuels are over 10% by the results of WIMS-AECL and MCNP-4B codes. Moreover, coolant void reactivity of the core loaded with plutonium fuel is more negative compared with that with uranium fuel because of spectrum hardening resulting from large void fraction

Present art of reactivity determination

International Nuclear Information System (INIS)

Kaneko, Yoshihiko; Nakano, Masafumi; Matsuura, Shojiro

1977-01-01

Experimental techniques for reactivity determination of a reactor have been one of the long standing subjects in reactor physics. Recently, such a requirement was proposed by the reactor designers and operators that the values of reactivity should be measured more accurately. This is because importance is emphasized for the role of reactivity to the performance of reactor safety, economics and operability. Motivated by the requirement, some remarkable progresses are being made for the improvement of the experimental techniques. Then, the present review summarizes the research activities on this subject, identifies several reactor physics problems to be overcome, and makes mention of the future targets. (auth.)

Assessment of solid reactive mixtures for the development of biological permeable reactive barriers

International Nuclear Information System (INIS)

Pagnanelli, Francesca; Viggi, Carolina Cruz; Mainelli, Sara; Toro, Luigi

2009-01-01

Solid reactive mixtures were tested as filling material for the development of biological permeable reactive barriers for the treatment of heavy metals contaminated waters. Mixture selection was performed by taking into account the different mechanisms operating in sulphate and cadmium removal with particular attention to bioprecipitation and sorption onto the organic matrices in the mixtures. Suspensions of eight reactive mixtures were tested for sulphate removal (initial concentration 3 g L -1 ). Each mixture was made up of four main functional components: a mix of organic sources for bacterial growth, a neutralizing agent, a porous medium and zero-valent iron. The best mixture among the tested ones (M8: 6% leaves, 9% compost, 3% zero-valent iron, 30% silica sand, 30% perlite, 22% limestone) presented optimal conditions for SRB growth (pH 7.8 ± 0.1; E h = -410 ± 5 mV) and 83% sulphate removal in 22 days (25% due to bioreduction, 32% due to sorption onto compost and 20% onto leaves). M8 mixture allowed the complete abatement of cadmium with a significant contribution of sorption over bioprecipitation (6% Cd removal due to SRB activity). Sorption properties, characterised by potentiometric titrations and related modelling, were mainly due to carboxylic sites of organic components used in reactive mixtures.

Reactivation with productivity

International Nuclear Information System (INIS)

Garcia, Carlos Hernando

2002-01-01

A market to five years that it will move near $63.000 millions, starting from the production of 254.000 reserves that Ecopetrol requires for its maintenance and operation, it was projected with base in the offer study and it demands that they carried out the universities Javeriana and Industrial of Santander for the Colombian Company of Petroleum around the metal mechanic sector. In accordance with the figures of the report, Ecopetrol, like one of the state entities selected by the national government to design pilot programs, guided to reactivate the Colombian industry; it is projecting a good perspective for the Colombian economy and the invigoration of the national productive sector. In practical terms, the report points out that Ecopetrol, in its different operative centers, will require in next five years the quantity of had restored before mentioned in the lines of mechanical stamps, centrifugal bombs, inter chambers of heat, compressors and valves of security; pieces that are elaborated by international makers in 99%. To produce them nationally would represent to the company an economy of 52% of the total value of the purchases in next five years and a reduction of time of delivery of 17 weeks to one week

Reactive bonding mediated high mass loading of individualized single-walled carbon nanotubes in an elastomeric polymer

Science.gov (United States)

Zhao, Liping; Li, Yongjin; Qiu, Jishan; You, Jichun; Dong, Wenyong; Cao, Xiaojun

2012-09-01

A reactive chemical bonding strategy was developed for the incorporation of a high mass loading of individual single-wall carbon nanotubes (SWCNTs) into an elastomeric matrix using a reactive ionic liquid as a linker. This method simultaneously prevented the agglomeration of SWCNTs and caused strong interfacial bonding, while the electronic properties of the SWCNTs remained intact. As a result, the high conductivity of the carbon nanotubes (CNTs) and the flexibility of the elastomeric matrix were retained, producing optimum electrical and mechanical properties. A composite material with a loading of 20 wt% SWCNTs was fabricated with excellent mechanical properties and a high conductivity (9500 S m-1). The method could be used to form transparent thin conductive films that could tolerate over 800 bend cycles at a bending angle of 180° while maintaining a constant sheet resistance.A reactive chemical bonding strategy was developed for the incorporation of a high mass loading of individual single-wall carbon nanotubes (SWCNTs) into an elastomeric matrix using a reactive ionic liquid as a linker. This method simultaneously prevented the agglomeration of SWCNTs and caused strong interfacial bonding, while the electronic properties of the SWCNTs remained intact. As a result, the high conductivity of the carbon nanotubes (CNTs) and the flexibility of the elastomeric matrix were retained, producing optimum electrical and mechanical properties. A composite material with a loading of 20 wt% SWCNTs was fabricated with excellent mechanical properties and a high conductivity (9500 S m-1). The method could be used to form transparent thin conductive films that could tolerate over 800 bend cycles at a bending angle of 180° while maintaining a constant sheet resistance. Electronic supplementary information (ESI) available: Conductivity test of the SEBS-SWCNTs film, transmission spectra and sheet resistance for the spin-coated SEBS-SWCNTs thin films on PET slides. See DOI: 10

Termination of nanoscale zero-valent iron reactivity by addition of bromate as a reducing reactivity competitor

Science.gov (United States)

Mines, Paul D.; Kaarsholm, Kamilla M. S.; Droumpali, Ariadni; Andersen, Henrik R.; Lee, Wontae; Hwang, Yuhoon

2017-09-01

Remediation of contaminated groundwater by nanoscale zero-valent iron (nZVI) is widely becoming a leading environmentally friendly solution throughout the globe. Since a wide range of various nZVI-containing materials have been developed for effective remediation, it is necessary to determine an appropriate way to terminate the reactivity of any nZVI-containing material for a practical experimental procedure. In this study, bimetallic Ni/Fe-NPs were prepared to enhance overall reduction kinetics owing to the catalytic reactivity of nickel on the surface of nZVI. We have tested several chemical strategies in order to terminate nZVI reactivity without altering the concentration of volatile compounds in the solution. The strategies include surface passivation in alkaline conditions by addition of carbonate, and consumption of nZVI by a reaction competitor. Four halogenated chemicals, trichloroethylene, 1,1,1-trichloroethane, atrazine, and 4-chlorophenol, were selected and tested as model groundwater contaminants. Addition of carbonate to passivate the nZVI surface was not effective for trichloroethylene. Nitrate and then bromate were applied to competitively consume nZVI by their faster reduction kinetics. Bromate proved to be more effective than nitrate, subsequently terminating nZVI reactivity for all four of the tested halogenated compounds. Furthermore, the suggested termination method using bromate was successfully applied to obtain trichloroethylene reduction kinetics. Herein, we report the simple and effective method to terminate the reactivity of nZVI by addition of a reducing reactivity competitor.

Steam-chemical reactivity for irradiated beryllium

Energy Technology Data Exchange (ETDEWEB)

Anderl, R.A.; McCarthy, K.A.; Oates, M.A.; Petti, D.A.; Pawelko, R.J.; Smolik, G.R. [Idaho National Engineering and Environmental Lab., Idaho Falls, ID (United States)

1998-01-01

This paper reports the results of an experimental investigation to determine the influence of neutron irradiation effects and annealing on the chemical reactivity of beryllium exposed to steam. The work entailed measurements of the H{sub 2} generation rates for unirradiated and irradiated Be and for irradiated Be that had been previously annealed at different temperatures ranging from 450degC to 1200degC. H{sub 2} generation rates were similar for irradiated and unirradiated Be in steam-chemical reactivity experiments at temperatures between 450degC and 600degC. For irradiated Be exposed to steam at 700degC, the chemical reactivity accelerated rapidly and the specimen experienced a temperature excursion. Enhanced chemical reactivity at temperatures between 400degC and 600degC was observed for irradiated Be annealed at temperatures of 700degC and higher. This reactivity enhancement could be accounted for by the increased specific surface area resulting from development of a surface-connected porosity in the irradiated-annealed Be. (author)

Application of ionizing radiation on industry waste treatment I. radiolysis of standard reactive dye Cibacron violet

International Nuclear Information System (INIS)

Winarti Andayani; Agustin Sumartono

1999-01-01

The effect of aeration, irradiation dose and pH on radiation degradation of reactive dye cibacron violet 2r in aqueous solution have been studied. Observation was done on the absorption spectrum before and after irradiation at various conditions. The percentage of degraded sample was analyzed by using HPLC with UV detector. The percentage of degradation was higher by aeration during irradiation. It suggest that oxygen is important for degradation of the dye molecule. Irradiation at neutral pH is preferred to obtain maximum degradation, since pH may affect the reactivity of the radicals produced by the radiolysis of water molecules. One of the degradation product that could be detected was oxalic acid. (author)

A Learning-Based Approach to Reactive Security

Science.gov (United States)

Barth, Adam; Rubinstein, Benjamin I. P.; Sundararajan, Mukund; Mitchell, John C.; Song, Dawn; Bartlett, Peter L.

Despite the conventional wisdom that proactive security is superior to reactive security, we show that reactive security can be competitive with proactive security as long as the reactive defender learns from past attacks instead of myopically overreacting to the last attack. Our game-theoretic model follows common practice in the security literature by making worst-case assumptions about the attacker: we grant the attacker complete knowledge of the defender's strategy and do not require the attacker to act rationally. In this model, we bound the competitive ratio between a reactive defense algorithm (which is inspired by online learning theory) and the best fixed proactive defense. Additionally, we show that, unlike proactive defenses, this reactive strategy is robust to a lack of information about the attacker's incentives and knowledge.

Immunological cross-reactivity to multiple autoantigens in patients with liver kidney microsomal type 1 autoimmune hepatitis.

Science.gov (United States)

Choudhuri, K; Gregorio, G V; Mieli-Vergani, G; Vergani, D

1998-11-01

We describe two patients with liver kidney microsomal antibody type 1 (LKM1)-positive autoimmune hepatitis (AIH) with associated endocrinopathies. The first patient had insulin-dependent diabetes (IDDM), and the second patient had Addison's disease and hypoparathyroidism, and is also positive for islet cell antibodies, without overt diabetes. To account for the existence of multiple endocrinopathy in these patients, we investigated whether there is sequence similarity between the target of LKM1 antibodies, cytochrome P4502D6 (CYP2D6), and other human proteins, and if so, whether this structural similarity produces a detectable cross-reactive immune response. Our database search identified two proteins, carboxypeptidase H, an autoantigen in insulin-dependent diabetes, and 21-hydroxylase, the major autoantigen in Addison's disease, that share sequence similarity to the second major LKM1 epitope on CYP2D6. We tested the reactivity of sera from these patients to the homologous regions of the three autoantigens using an enzyme-linked immunosorbent assay (ELISA). The cut-off for positivity was established by testing sera from 22 healthy children. To determine the significance of reactivity to the peptide homologues of the three autoantigens, we investigated 16 additional patients with LKM1 AIH and 20 children with chronic hepatitis B virus infection as pathological controls. We found that reactivity to the second major epitope of CYP2D6 is significantly associated with reactivity to the homologous regions of carboxypeptidase H (CPH) and 21-hydroxylase (21-OHase) in patients with LKM1 AIH, and that this simultaneous recognition is cross-reactive. We suggest that a cross-reactive immune response between homologous autoantigens may contribute to the development of multiple endocrinopathies in LKM1 AIH.

Reactive power compensation a practical guide

CERN Document Server

Hofmann, Wolfgang; Just, Wolfgang

2012-01-01

The comprehensive resource on reactive power compensation, presenting the design, application and operation of reactive power equipment and installations The area of reactive power compensation is gaining increasing importance worldwide. If suitably designed, it is capable of improving voltage quality significantly, meaning that losses in equipment and power systems are reduced, the permissible loading of equipment can be increased, and the over-all stability of system operation improved. Ultimately, energy use and CO2 emisson are reduced. This unique guide discusses the

High-rate reactive magnetron sputtering of zirconia films for laser optics applications

International Nuclear Information System (INIS)

Juskevicius, K.; Subacius, A.; Drazdys, R.; Juskenas, R.; Audronis, M.; Matthews, A.; Leyland, A.

2014-01-01

ZrO 2 exhibits low optical absorption in the near-UV range and is one of the highest laser-induced damage threshold (LIDT) materials; it is, therefore, very attractive for laser optics applications. This paper reports explorations of reactive sputtering technology for deposition of ZrO 2 films with low extinction coefficient k values in the UV spectrum region at low substrate temperature. A high deposition rate (64 % of the pure metal rate) process is obtained by employing active feedback reactive gas control which creates a stable and repeatable deposition processes in the transition region. Substrate heating at 200 C was found to have no significant effect on the optical ZrO 2 film properties. The addition of nitrogen to a closed-loop controlled process was found to have mostly negative effects in terms of deposition rate and optical properties. Open-loop O 2 gas-regulated ZrO 2 film deposition is slow and requires elevated (200 C) substrate temperature or post-deposition annealing to reduce absorption losses. Refractive indices of the films were distributed in the range n = 2.05-2.20 at 1,000 nm and extinction coefficients were in the range k = 0.6 x 10 -4 and 4.8 x 10 -3 at 350 nm. X-ray diffraction analysis showed crystalline ZrO 2 films consisted of monoclinic + tetragonal phases when produced in Ar/O 2 atmosphere and monoclinic + rhombohedral or a single rhombohedral phase when produced in Ar/O 2 + N 2 . Optical and physical properties of the ZrO 2 layers produced in this study are suitable for high-power laser applications in the near-UV range. (orig.)

Method for reactivating solid catalysts used in alkylation reactions

Science.gov (United States)

Ginosar, Daniel M.; Thompson, David N.; Coates, Kyle; Zalewski, David J.; Fox, Robert V.

2003-06-17

A method for reactivating a solid alkylation catalyst is provided which can be performed within a reactor that contains the alkylation catalyst or outside the reactor. Effective catalyst reactivation is achieved whether the catalyst is completely deactivated or partially deactivated. A fluid reactivating agent is employed to dissolve catalyst fouling agents and also to react with such agents and carry away the reaction products. The deactivated catalyst is contacted with the fluid reactivating agent under pressure and temperature conditions such that the fluid reactivating agent is dense enough to effectively dissolve the fouling agents and any reaction products of the fouling agents and the reactivating agent. Useful pressures and temperatures for reactivation include near-critical, critical, and supercritical pressures and temperatures for the reactivating agent. The fluid reactivating agent can include, for example, a branched paraffin containing at least one tertiary carbon atom, or a compound that can be isomerized to a molecule containing at least one tertiary carbon atom.

Evaluation of reactivity shutdown margin for nuclear fuel reload optimization

International Nuclear Information System (INIS)

Wong, Hing-Ip; Maldonado, G.I.

1995-01-01

The FORMOSA-P code is a nuclear fuel management optimization package that combines simulated annealing (SA) and nodal generalized perturbation theory (GPT). Recent studies at Electricite de France (EdF-Clamart) have produced good results for power-peaking minimizations under multiple limiting control rod configurations. However, since the reactivity shutdown margin is not explicitly treated as an objective or constraint function, then any optimal loading patterns (LPs) are not guaranteed to yield an adequate shutdown margin (SDM). This study describes the implementation of the SDM calculation within a FORMOSA-P optimization. Maintaining all additional computational requirements to a minimum was a key consideration

Physical–chemical and biological behavior of an amorphous calcium phosphate thin film produced by RF-magnetron sputtering

International Nuclear Information System (INIS)

Santos, Euler A. dos; Moldovan, Simona; Mateescu, Mihaela; Faerber, Jacques; Acosta, Manuel; Pelletier, Hervé; Anselme, Karine; Werckmann, Jacques

2012-01-01

This work evaluates the thermal reactivity and the biological reactivity of an amorphous calcium phosphate thin film produced by radio frequency (RF) magnetron sputtering onto titanium substrates. The analyses showed that the sputtering conditions used in this work led to the deposition of an amorphous calcium phosphate. The thermal treatment of this amorphous coating in the presence of H 2 O and CO 2 promoted the formation of a carbonated HA crystalline coating with the entrance of CO 3 2− ions into the hydroxyl HA lattice. When immersed in culture medium, the amorphous and carbonated coatings exhibited a remarkable instability. The presence of proteins increased the dissolution process, which was confirmed by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) analyses. Moreover, the carbonated HA coating induced precipitation independently of the presence of proteins under dynamic conditions. Despite this surface instability, this reactive calcium phosphate significantly improved the cellular behavior. The cell proliferation was higher on the Ticp than on the calcium phosphate coatings, but the two coatings increased cellular spreading and stress fiber formation. In this sense, the presence of reactive calcium phosphate coatings can stimulate cellular behavior. - Highlights: ► Functionalization of Ti with reactive CaP thin film by RF-magnetron sputtering. ► De-hydroxylation facilitating the insertion of CO 3 2− into the HA lattice. ► High surface reactivity in the presence of culture medium. ► Cell behavior improved by the presence of reactive films.

Development of various welding techniques for refractory and reactive metals and alloys

International Nuclear Information System (INIS)

Tonpe, Sunil; Saibaba, N.

2016-01-01

Nuclear Fuel Complex (NFC), Hyderabad, India with its excellent manufacturing facilities, produces nuclear fuel and structural components for nuclear reactors. NFC has taken up the challenging job of production of various critical components made out of refractory and reactive metals and alloys for nuclear and aerospace applications as an indigenization import substitute program. Refractory metals are prime candidates for many high temperature aerospace components because of refractory metal's high melting points and inherent creep resistance. The use of refractory metals is often limited because of their poor room temperature properties, inadequate oxidation resistance at elevated temperatures, difficulties associated with joining or welding etc. These advanced materials demand stringent requirement with respect to chemistry, dimensional tolerances, mechanical and metallurgical properties. This paper discusses in detail various welding techniques adopted in NFC for refractory and reactive metals and alloys such as Nb, Zr, Ti, Ta, Zircaloy, Titanium-half alloy etc. to manufacture various components and assemblies required for nuclear and aerospace applications

Modeling and simulation of reactive flows

CERN Document Server

Bortoli, De AL; Pereira, Felipe

2015-01-01

Modelling and Simulation of Reactive Flows presents information on modeling and how to numerically solve reactive flows. The book offers a distinctive approach that combines diffusion flames and geochemical flow problems, providing users with a comprehensive resource that bridges the gap for scientists, engineers, and the industry. Specifically, the book looks at the basic concepts related to reaction rates, chemical kinetics, and the development of reduced kinetic mechanisms. It considers the most common methods used in practical situations, along with equations for reactive flows, and va

Structural and reactivity models for copper oxygenases: cooperative effects and novel reactivities.

Science.gov (United States)

Serrano-Plana, Joan; Garcia-Bosch, Isaac; Company, Anna; Costas, Miquel

2015-08-18

Dioxygen is widely used in nature as oxidant. Nature itself has served as inspiration to use O2 in chemical synthesis. However, the use of dioxygen as an oxidant is not straightforward. Its triplet ground-state electronic structure makes it unreactive toward most organic substrates. In natural systems, metalloenzymes activate O2 by reducing it to more reactive peroxide (O2(2-)) or superoxide (O2(-)) forms. Over the years, the development of model systems containing transition metals has become a convenient tool for unravelling O2-activation mechanistic aspects and reproducing the oxidative activity of enzymes. Several copper-based systems have been developed within this area. Tyrosinase is a copper-based O2-activating enzyme, whose structure and reactivity have been widely studied, and that serves as a paradigm for O2 activation at a dimetal site. It contains a dicopper center in its active site, and it catalyzes the regioselective ortho-hydroxylation of phenols to catechols and further oxidation to quinones. This represents an important step in melanin biosynthesis and it is mediated by a dicopper(II) side-on peroxo intermediate species. In the present accounts, our research in the field of copper models for oxygen activation is collected. We have developed m-xylyl linked dicopper systems that mimick structural and reactivity aspects of tyrosinase. Synergistic cooperation of the two copper(I) centers results in O2 binding and formation of bis(μ-oxo)dicopper(III) cores. These in turn bind and ortho-hydroxylate phenolates via an electrophilic attack of the oxo ligand over the arene. Interestingly the bis(μ-oxo)dicopper(III) cores can also engage in ortho-hydroxylation-defluorination of deprotonated 2-fluorophenols, substrates that are well-known enzyme inhibitors. Analysis of Cu2O2 species with different binding modes show that only the bis(μ-oxo)dicopper(III) cores can mediate the reaction. Finally, the use of unsymmetric systems for oxygen activation is a field

Cardiovascular reactivity to video game predicts subsequent blood pressure increases in young men: The CARDIA study.

Science.gov (United States)

Markovitz, J H; Raczynski, J M; Wallace, D; Chettur, V; Chesney, M A

1998-01-01

This study was undertaken to determine the relationship between heightened reactivity of blood pressure (BP) during stress and 5-year changes in blood pressure and hypertensive status, using the CARDIA study. A total of 3364 participants (910 white men, 909 white women, 678 black men, and 867 black women), initially 20 to 32 years old and normotensive, were included. Cardiovascular reactivity to psychological stressors (video game and star-tracing tasks for 3 minutes, cold pressor test for 1 minute) was measured in 1987-1988. We then examined reactivity as a predictor of significant BP change (> or = 8 mm Hg, thought to represent a clinically significant increase) over the next 5 years. Logistic regression models were used to control for potential covariates. Significant BP change and the development of hypertension (BP greater than 140/90 or taking medication for hypertension) over the 5-year follow-up were examined in separate analyses. Increased systolic blood pressure (SBP) reactivity to the video game was associated with a significant 5-year SBP increase among the entire cohort, independent of resting SBP (p men but not for women. Reactivity to the star-tracing task or the cold pressor test did not predict significant BP change. Among black men only, new hypertensives (N = 36) had greater diastolic blood pressure (DBP) reactivity to the video game (p = .01). Although BP reactivity to all physical and mental stressors used in this study did not consistently predict 5-year change in BP in this young cohort, the results indicate that reactivity to a video game stressor predicts 5-year change in BP and early hypertension among young adult men. These findings are consistent with other studies showing the usefulness of stressors producing a primarily beta-adrenergic response in predicting BP change and hypertension. The results may be limited by the shortened initial rest and recovery periods used in the CARDIA protocol.

One-Bath Pretreatment for Enhanced Color Yield of Ink-Jet Prints Using Reactive Inks

Directory of Open Access Journals (Sweden)

Wei Ma

2017-11-01

Full Text Available In order to facilely increase the color yield of ink-jet prints using reactive inks, one-bath pretreatment of cotton fabrics with pretreatment formulation containing sodium alginate, glycidyltrimethylammonium chloride (GTA, sodium hydroxide, and urea is designed for realizing sizing and cationization at the same time. The pretreatment conditions, including the concentrations of GTA and alkali, baking temperature, and time are optimized based on the result of thecolor yield on cationic cotton for magenta ink. The mechanism for color yield enhancement on GTA-modified fabrics is discussed and the stability of GTA in the print paste is investigated. Scanning electron microscopey, tear strength, and thermogravimetric analysis of the modified and unmodified cotton are studied and compared. Using the optimal pretreatment conditions, color yield on the cationic cotton for magenta, cyan, yellow, and black reactive inks are increased by 128.7%, 142.5%, 71.0%, and 38.1%, respectively, compared with the corresponding color yield on the uncationized cotton. Much less wastewater is produced using this one-bath pretreatment method. Colorfastness of the reactive dyes on the modified and unmodified cotton is compared and boundary clarity between different colors is evaluated by ink-jet printing of colorful patterns.

High impact strength polymers having novel nano-structures produced via reactive extrusion

Science.gov (United States)

Tortorella, Nathan Fraser

A major focus of scientists and engineers over the last century has been to increase the impact strength and therefore reduce the brittleness of materials. By altering and adding energy absorption mechanisms, brittle failure can be averted. Isotactic polypropylene (PP) is the focus of this dissertation because it is an extremely low cost, high volume, versatile plastic but behaves in a brittle manner at or below room temperature or in a notched state. Early work on impact modification of polypropylene focused on blending energy-absorbing low density elastomers and rubbers. These binary blends all had a common problem---an increase in impact strength was paralleled by a significant decrease in both elastic modulus and yield stress. Reactive extrusion processing has allowed the in-situ compatibilization of isotactic polypropylene and metallocene-catalyzed ethylene-octene copolymers (EOCs). This process involves combining both the comonomer and vector fluid approaches to grafting polyolefins. Styrene monomer and a multifunctional acrylate monomer undergo peroxide-induced copolymerization and grafting in the presence of both PP and EOC. This results in a phase separated alloy with an impact strength over 13 times that of pure polypropylene and double that of the physical blend. There is also a significant improvement in stress-strain performance when comparing the alloys to physical blend counterparts. Many researchers have categorized the necessary components to toughening polypropylene as pertaining to the amorphous phase. The alloys described in this dissertation meet the criteria put forth by these researchers, namely low density, crystallinity, and modulus of the elastomer phase, sub-micron particle diameter, close inter-particle distance, and a high degree of entanglements of both the PP matrix phase and EOC minor phase. But many people neglect to study the crystalline state of impact modified PP in conjunction with the amorphous phase. This work shows that the

A benchmark on the calculation of kinetic parameters based on reactivity effect experiments in the CROCUS reactor

International Nuclear Information System (INIS)

Paratte, J.M.; Frueh, R.; Kasemeyer, U.; Kalugin, M.A.; Timm, W.; Chawla, R.

2006-01-01

Measurements in the CROCUS reactor at EPFL, Lausanne, are reported for the critical water level and the inverse reactor period for several different sets of delayed supercritical conditions. The experimental configurations were also calculated by four different calculation methods. For each of the supercritical configurations, the absolute reactivity value has been determined in two different ways, viz.: (i) through direct comparison of the multiplication factor obtained employing a given calculation method with the corresponding value for the critical case (calculated reactivity: ρ calc ); (ii) by application of the inhour equation using the kinetic parameters obtained for the critical configuration and the measured inverse reactor period (measured reactivity: ρ meas ). The calculated multiplication factors for the reference critical configuration, as well as ρ calc for the supercritical cases, are found to be in good agreement. However, the values of ρ meas produced by two of the applied calculation methods differ appreciably from the corresponding ρ calc values, clearly indicating deficiencies in the kinetic parameters obtained from these methods

Dissecting cross-reactivity in hymenoptera venom allergy by circumvention of alpha-1,3-core fucosylation.

Science.gov (United States)

Seismann, Henning; Blank, Simon; Braren, Ingke; Greunke, Kerstin; Cifuentes, Liliana; Grunwald, Thomas; Bredehorst, Reinhard; Ollert, Markus; Spillner, Edzard

2010-01-01

Hymenoptera venom allergy is known to cause life-threatening and sometimes fatal IgE-mediated anaphylactic reactions in allergic individuals. About 30-50% of patients with insect venom allergy have IgE antibodies that react with both honeybee and yellow jacket venom. Apart from true double sensitisation, IgE against cross-reactive carbohydrate determinants (CCD) are the most frequent cause of multiple reactivities severely hampering the diagnosis and design of therapeutic strategies by clinically irrelevant test results. In this study we addressed allergenic cross-reactivity using a recombinant approach by employing cell lines with variant capacities of alpha-1,3-core fucosylation. The venom hyaluronidases, supposed major allergens implicated in cross-reactivity phenomena, from honeybee (Api m 2) and yellow jacket (Ves v 2a and its putative isoform Ves v 2b) as well as the human alpha-2HS-glycoprotein as control, were produced in different insect cell lines. In stark contrast to production in Trichoplusia ni (HighFive) cells, alpha-1,3-core fucosylation was absent or immunologically negligible after production in Spodoptera frugiperda (Sf9) cells. Consistently, co-expression of honeybee alpha-1,3-fucosyltransferase in Sf9 cells resulted in the reconstitution of CCD reactivity. Re-evaluation of differentially fucosylated hyaluronidases by screening of individual venom-sensitised sera emphasised the allergenic relevance of Api m 2 beyond its carbohydrate epitopes. In contrast, the vespid hyaluronidases, for which a predominance of Ves v 2b could be shown, exhibited pronounced and primary carbohydrate reactivity rendering their relevance in the context of allergy questionable. These findings show that the use of recombinant molecules devoid of CCDs represents a novel strategy with major implications for diagnostic and therapeutic approaches. Copyright 2010 Elsevier Ltd. All rights reserved.

Activation of Reactive MALDI Adduct Ions Enables Differentiation of Dihydroxylated Vitamin D Isomers

Science.gov (United States)

Qi, Yulin; Müller, Miriam J.; Volmer, Dietrich A.

2017-12-01

Vitamin D compounds are secosteroids, which are best known for their role in bone health. More recent studies have shown that vitamin D metabolites and catabolites such as dihydroxylated species (e.g., 1,25- and 24,25-dihydroxyvitamin D3) play key roles in the pathologies of various diseases. Identification of these isomers by mass spectrometry is challenging and currently relies on liquid chromatography, as the isomers exhibit virtually identical product ion spectra under collision induced dissociation conditions. Here, we developed a simple MALDI-CID method that utilizes ion activation of reactive analyte/matrix adducts to distinguish isomeric dihydroxyvitamin D3 species, without the need for chromatography separation or chemical derivatization techniques. Specifically, reactive 1,5-diaminonaphthalene adducts of dihydroxyvitamin D3 compounds formed during MADI were activated and specific cleavages in the secosteroid's backbone structure were achieved that produced isomer-diagnostic fragment ions. [Figure not available: see fulltext.

Twelve Theses on Reactive Rules for the Web

OpenAIRE

Bry, François; Eckert, Michael; Patranjan, Paula-Lavinia

2006-01-01

Reactivity, the ability to detect events and respond to them automatically through reactive programs, is a key requirement in many present-day information systems. Work on Web Services re ects the need for support of reactivity on a higher abstraction level than just message exchange by HTTP. This article presents the composite event query facilities of the reactive rule-based programming language XChange. Composite events are important in the dynamic world of the Web whe...

On Variable Reverse Power Flow-Part I: Active-Reactive Optimal Power Flow with Reactive Power of Wind Stations

Directory of Open Access Journals (Sweden)

Aouss Gabash

2016-02-01

Full Text Available It has recently been shown that using battery storage systems (BSSs to provide reactive power provision in a medium-voltage (MV active distribution network (ADN with embedded wind stations (WSs can lead to a huge amount of reverse power to an upstream transmission network (TN. However, unity power factors (PFs of WSs were assumed in those studies to analyze the potential of BSSs. Therefore, in this paper (Part-I, we aim to further explore the pure reactive power potential of WSs (i.e., without BSSs by investigating the issue of variable reverse power flow under different limits on PFs in an electricity market model. The main contributions of this work are summarized as follows: (1 Introducing the reactive power capability of WSs in the optimization model of the active-reactive optimal power flow (A-R-OPF and highlighting the benefits/impacts under different limits on PFs. (2 Investigating the impacts of different agreements for variable reverse power flow on the operation of an ADN under different demand scenarios. (3 Derivation of the function of reactive energy losses in the grid with an equivalent-π circuit and comparing its value with active energy losses. (4 Balancing the energy curtailment of wind generation, active-reactive energy losses in the grid and active-reactive energy import-export by a meter-based method. In Part-II, the potential of the developed model is studied through analyzing an electricity market model and a 41-bus network with different locations of WSs.

Prediction of N-nitrosodimethylamine (NDMA) formation as a disinfection by-product.

Science.gov (United States)

Kim, Jongo; Clevenger, Thomas E

2007-06-25

This study investigated the possibility of a statistical model application for the prediction of N-nitrosodimethylamine (NDMA) formation. The NDMA formation was studied as a function of monochloramine concentration (0.001-5mM) at fixed dimethylamine (DMA) concentrations of 0.01mM or 0.05mM. Excellent linear correlations were observed between the molar ratio of monochloramine to DMA and the NDMA formation on a log scale at pH 7 and 8. When a developed prediction equation was applied to a previously reported study, a good result was obtained. The statistical model appears to predict adequately NDMA concentrations if other NDMA precursors are excluded. Using the predictive tool, a simple and approximate calculation of NDMA formation can be obtained in drinking water systems.

A Peptide-Fc Opsonin with Pan-Amyloid Reactivity

Directory of Open Access Journals (Sweden)

James S. Foster

2017-09-01

Full Text Available There is a continuing need for therapeutic interventions for patients with the protein misfolding disorders that result in systemic amyloidosis. Recently, specific antibodies have been employed to treat AL amyloidosis by opsonizing tissue amyloid deposits thereby inducing cell-mediated dissolution and organ improvement. To develop a pan-amyloid therapeutic agent, we have produced an Fc-fusion product incorporating a peptide, p5, which binds many if not all forms of amyloid. This protein, designated Fcp5, expressed in mammalian cells, forms the desired bivalent dimer structure and retains pan-amyloid reactivity similar to the p5 peptide as measured by immunosorbent assays, immunohistochemistry, surface plasmon resonance, and pulldown assays using radioiodinated Fcp5. Additionally, Fcp5 was capable of opsonizing amyloid fibrils in vitro using a pH-sensitive fluorescence assay of phagocytosis. In mice,125 I-labeled Fcp5 exhibited an extended serum circulation time, relative to the p5 peptide. It specifically bound AA amyloid deposits in diseased mice, as evidenced by biodistribution and microautoradiographic methods, which coincided with an increase in active, Iba-1-positive macrophages in the liver at 48 h postinjection of Fcp5. In healthy mice, no specific tissue accumulation was observed. The data indicate that polybasic, pan-amyloid-targeting peptides, in the context of an Fc fusion, can yield amyloid reactive, opsonizing reagents that may serve as next-generation immunotherapeutics.

Fabrication of antireflective nanostructures for crystalline silicon solar cells by reactive ion etching

International Nuclear Information System (INIS)

Lin, Hsin-Han; Chen, Wen-Hua; Wang, Chi-Jen; Hong, Franklin Chau-Nan

2013-01-01

In this study we have fabricated large-area (15 × 15 cm 2 ) subwavelength antireflection structure on poly-Si substrates to reduce their solar reflectivity. A reactive ion etching system was used to fabricate nanostructures on the poly-silicon surface. Reactive gases, composed of chlorine (Cl 2 ), sulfur hexafluoride (SF 6 ) and oxygen (O 2 ), were activated to fabricate nanoscale pyramids by RF plasma. The poly-Si substrates were etched in various gas compositions for 6–10 min to form nano-pyramids. The sizes of pyramids were about 200–300 nm in heights and about 100 nm in width. Besides the nanoscale features, the high pyramid density on the poly-Si surface is another important factor to reduce the reflectivity. Low-reflectivity surface was fabricated with reflectivity significantly reduced down to < 2% for photons in a wavelength range of 500–900 nm. - Highlights: ► Large-area (15 × 15 cm 2 ) antireflection structures fabricated on poly-Si substrates ► Si nano-pyramids produced by utilizing self-masked reactive ion etching process ► High density of nanoscale pyramids was formed on the entire substrate surface. ► Surface reflectivity below 2% was achieved in the wavelength range of 500–900 nm

Insertion material for controlling reactivity

International Nuclear Information System (INIS)

Baba, Iwao.

1994-01-01

Moderators and a group of suspended materials having substantially the same density as the moderator are sealed in a hollow rod vertically inserted to a fuel assembly. Specifically, the group of suspended materials is adapted to have a density changing stepwise from density of the moderator at the exit temperature of the reactor core to that at the inlet temperature of the reactor core. Reactivity is selectively controlled for a portion of high power and a portion of high reactivity by utilizing the density of the moderator and the distribution of the density. That is, if the power distribution is flat, the density of the moderators changes at a constant rate over the vertical direction of the reactor core and the suspended materials stay at a portion of the same density, to form a uniform distribution. Further, upon reactor shutdown, since the liquid temperature of the moderators is lowered and the density is increased, all of beads are collected at the upper portion to remove water at the upper portion of the reactor core of low burnup degree thereby selectively controlling the reactivity at a portion of high power and a portion of high reactivity. (N.H.)

Treatment of dyeing wastewater including reactive dyes (Reactive ...

African Journals Online (AJOL)

Fungal growth was not observed at pH 2. Maximum fungal decolourisation ocurred at pH 3 for anionic reactive dyes (RR, RBB, RB) and pH 6 for cationic MB dye. The fungal dye bioremoval was associated with the surface charge of the fungus due to electrostatic interactions. Growing R. arrhizus strain decolourised 100% of ...

Parameters estimation for reactive transport: A way to test the validity of a reactive model

Science.gov (United States)

Aggarwal, Mohit; Cheikh Anta Ndiaye, Mame; Carrayrou, Jérôme

The chemical parameters used in reactive transport models are not known accurately due to the complexity and the heterogeneous conditions of a real domain. We will present an efficient algorithm in order to estimate the chemical parameters using Monte-Carlo method. Monte-Carlo methods are very robust for the optimisation of the highly non-linear mathematical model describing reactive transport. Reactive transport of tributyltin (TBT) through natural quartz sand at seven different pHs is taken as the test case. Our algorithm will be used to estimate the chemical parameters of the sorption of TBT onto the natural quartz sand. By testing and comparing three models of surface complexation, we show that the proposed adsorption model cannot explain the experimental data.

Reactivity monitoring during reactor-reloading operations

International Nuclear Information System (INIS)

Baumann, N.P.; Ahlfeld, C.F.; Ridgely, G.C.

1983-01-01

At the Savannah River Plant (SRP) reloading operations during shutdown present special considerations in reactivity monitoring and control. Large reactivity changes may occur during reloading operations because of the heterogeneous nature of some core designs. This paper describes an improved monitoring system

Inverse kinetics equations for on line measurement of reactivity using personal computer

International Nuclear Information System (INIS)

Ratemi, Wajdi; El Gadamsi, Walied; Beleid, Abdul Kariem

1993-01-01

Computer with their astonishing speed of calculations along with their easy connection to real systems, are very appropriate for digital measurements of real system variables. In the nuclear industry, such computer application will produce compact control rooms of real power plants, where information and results display can be obtained through push button concept. In our study, we use two personal computers for the purpose of simulation and measurement. One of them is used as a digital simulator to a real reactor, where we effectively simulate the reactor power through a cross talk network. The computed power is passed at certain chosen sampling time to the other computer. The purpose of the other computer is to use the inverse kinetics equations to calculate the reactivity parameter based on the received power and then it performs on line display of the power curve and the reactivity curve using color graphics. In this study, we use the one group version of the inverse kinetics algorithm which can easily be extended to larger group version. The language of programming used in Turbo BASIC, which is very comparable, in terms of efficiency, to FORTRAN language, besides its effective graphics routines. With the use of the extended version of the Inverse Kinetics algorithm, we can effectively apply this techniques of measurement for the purpose of on line display of the reactivity of the Tajoura Research Reactor. (author)

Oxidized amino acid residues in the vicinity of Q(A and Pheo(D1 of the photosystem II reaction center: putative generation sites of reducing-side reactive oxygen species.

Directory of Open Access Journals (Sweden)

Laurie K Frankel

Full Text Available Under a variety of stress conditions, Photosystem II produces reactive oxygen species on both the reducing and oxidizing sides of the photosystem. A number of different sites including the Mn4O5Ca cluster, P680, PheoD1, QA, QB and cytochrome b559 have been hypothesized to produce reactive oxygen species in the photosystem. In this communication using Fourier-transform ion cyclotron resonance mass spectrometry we have identified several residues on the D1 and D2 proteins from spinach which are oxidatively modified and in close proximity to QA (D1 residues (239F, (241Q, (242E and the D2 residues (238P, (239T, (242E and (247M and PheoD1 (D1 residues (130E, (133L and (135F. These residues may be associated with reactive oxygen species exit pathways located on the reducing side of the photosystem, and their modification may indicate that both QA and PheoD1 are sources of reactive oxygen species on the reducing side of Photosystem II.

The reactive extrusion of thermoplastic polyurethane

NARCIS (Netherlands)

Verhoeven, Vincent Wilhelmus Andreas

2006-01-01

The objective of this thesis was to increase the understanding of the reactive extrusion of thermoplastic polyurethane. Overall, several issues were identified: • Using a relative simple extrusion model, the reactive extrusion process can be described. This model can be used to further investigate

A XANES Study of Sulfur Speciation and Reactivity in Cokes for Anodes Used in Aluminum Production

Science.gov (United States)

Jahrsengene, Gøril; Wells, Hannah C.; Rørvik, Stein; Ratvik, Arne Petter; Haverkamp, Richard G.; Svensson, Ann Mari

2018-06-01

Availability of anode raw materials in the growing aluminum industry results in a wider range of petroleum cokes being used to produce carbon anodes. The boundary between anode grade cokes and what previously was considered non-anode grades are no longer as distinct as before, leading to introduction of cokes with higher sulfur and higher trace metal impurity content in anode manufacturing. In this work, the chemical nature of sulfur in five industrial cokes, ranging from 1.42 to 5.54 wt pct S, was investigated with K-edge XANES, while the reactivity of the cokes towards CO2 was measured by a standard mass loss test. XANES identified most of the sulfur as organic sulfur compounds. In addition, a significant amount is identified (16 to 53 pct) as S-S bound sulfur. A strong inverse correlation is observed between CO2-reactivity and S-S bound sulfur in the cokes, indicating that the reduction in reactivity is more dependent on the amount of this type of sulfur compound rather than the total amount of sulfur or the amount of organic sulfur.

Development of a UNIX network compatible reactivity computer

International Nuclear Information System (INIS)

Sanchez, R.F.; Edwards, R.M.

1996-01-01

A state-of-the-art UNIX network compatible controller and UNIX host workstation with MATLAB/SIMULINK software were used to develop, implement, and validate a digital reactivity calculation. An objective of the development was to determine why a Macintosh-based reactivity computer reactivity output drifted intolerably

Photolysis of Mono- and Dichloramines in UV/Hydrogen Peroxide: Effects on 1,4-Dioxane Removal and Relevance in Water Reuse.

Science.gov (United States)

Patton, Samuel; Romano, Mariano; Naddeo, Vincenzo; Ishida, Kenneth P; Liu, Haizhou

2018-06-05

Growing demands and increasing scarcity of fresh water resources necessitate potable water reuse, which has been implemented with the aid of UV-based advanced oxidation processes (UV/AOPs) that remove potentially hazardous trace organic contaminants from reclaimed water. During the potable reuse treatment process, chloramines are added to prevent membrane fouling that are carried over to the UV/AOP, where hydrogen peroxide (H 2 O 2 ) is commonly added. However, the impact of chloramines on the photolysis of H 2 O 2 and the overall performance of the UV/AOP remains unknown. This study investigated the impacts of the photochemistry of monochloramine (NH 2 Cl) and dichloramine (NHCl 2 ) associated with the photolysis of H 2 O 2 on the degradation of 1,4-dioxane (1,4-D), a trace organic contaminant ubiquitous in recycled water. Results indicated that NH 2 Cl and NHCl 2 alone functioned as oxidants upon UV photolysis, which produced HO • and Cl 2 •- as the two primary oxidative radicals. The speciation of chloramines did not have a significant impact on the degradation kinetics. The inclusion of monochloramine in UV/H 2 O 2 greatly decreased 1,4-D removal efficiency. HO • was the major radical in the mixed H 2 O 2 /chloramine system. Results from this study suggest that recognizing the existence of chloramines in UV/H 2 O 2 systems is important for predicting UV/AOP performance in the treatment train of potable reuse.

Reactivity estimation using digital nonlinear H∞ estimator for VHTRC experiment

International Nuclear Information System (INIS)

Suzuki, Katsuo; Nabeshima, Kunihiko; Yamane, Tsuyoshi

2003-01-01

On-line and real-time estimation of time-varying reactivity in a nuclear reactor in necessary for early detection of reactivity anomaly and safe operation. Using a digital nonlinear H ∞ estimator, an experiment of real-time dynamic reactivity estimation was carried out in the Very High Temperature Reactor Critical Assembly (VHTRC) of Japan Atomic Energy Research Institute. Some technical issues of the experiment are described, such as reactivity insertion, data sampling frequency, anti-aliasing filter, experimental circuit and digitalising nonlinear H ∞ reactivity estimator, and so on. Then, we discussed the experimental results obtained by the digital nonlinear H ∞ estimator with sampled data of the nuclear instrumentation signal for the power responses under various reactivity insertions. Good performances of estimated reactivity were observed, with almost no delay to the true reactivity and sufficient accuracy between 0.05 cent and 0.1 cent. The experiment shows that real-time reactivity for data sampling period of 10 ms can be certainly realized. From the results of the experiment, it is concluded that the digital nonlinear H ∞ reactivity estimator can be applied as on-line real-time reactivity meter for actual nuclear plants. (author)

Radiation enhanced reactivation of herpes simplex virus: effect of caffeine.

Science.gov (United States)

Hellman, K B; Lytle, C D; Bockstahler, L E

1976-09-01

Ultaviolet enhanced (Weigle) reactivation of UV-irradiated herpes simplex virus in UV-irradiated CV-1 monkey kidney cell monolayers was decreased by caffeine. X-ray enhanced reactivation of UV-irradiated virus in X-irradiated monolayers (X-ray reactivation) and UV- or X-ray-inactivated capacity of the cells to support unirradiated virus plaque formation were unaffected by caffeine. The results suggest that a caffeine-sensitive process is necessary for the expression of Weigle reactivation for herpes virus. Since cafeine did not significantly affect X-ray reactivation, different mechanisms may be responsible for the expression of Weigle reactivation and X-ray reactivation.

Radiation enhaced reactivation of herpes simplex virus: effect of caffeine

International Nuclear Information System (INIS)

Hellman, K.B.; Lytle, C.D.; Bockstahler, L.E.

1976-01-01

Ultraviolet enhanced (Weigle) reactivation of UV-irradiated herpes simplex virus in UV-irradiated CV-1 monkey kidney cell monolayers was decreased by caffeine. X-ray enhanced reactivation of UV-irradiated virus in X-irradiated monolayers (X-ray reactivation) and UV- or X-ray-inactivated capacity of the cells to support unirradiated virus plaque formation were unaffected by caffeine. The results suggest that a caffeine-sensitive process is necessary for the expression of Weigle reactivation for herpes virus. Since caffeine did not significantly affect X-ray reactivation, different mechanisms may be responsible for the expression of Weigle reactivation and X-ray reactivation

The chemical reactivity of the Martian soil and implications for future missions

Science.gov (United States)

Zent, Aaron P.; Mckay, Christopher P.

1994-01-01

Possible interpretations of the results of the Viking Biology Experiments suggest that greater than 1 ppm of a thermally labile oxidant, perhaps H2O2, and about 10 ppm of a thermally stable oxidant are present in the martian soil. We reexamine these results and discuss implications for future missions, the search for organics on Mars, and the possible health and engineering effects for human exploration. We conclude that further characterization of the reactivity of the martian regolith materials is warrented-although if our present understanding is correct the oxidant does not pose a hazard to humans. There are difficulties in explaining the reactivity of the Martian soil by oxidants. Most bulk phase compounds that are capable of oxidizing H2O to O2 per the Gas Exchange Experiment (GEx) are thermally labile or unstable against reduction by atmospheric CO2. Models invoking trapped O2 or peroxynitrates (NOO2(-)) require an unlikely geologic history for the Viking Lander 2 site. Most suggested oxidants, including H2O2, are expected to decompose rapidly under martian UV. Nonetheless, we conclude that the best model for the martian soil contains oxidants produced by heterogeneous chemical reactions with a photochemically produced atmospheric oxidant. The GEx results may be due to catalytic decomposition of an unstable oxidizing material by H2O. We show that interfacial reaction sites covering less than 1% of the available soil surfaces could explain the Viking Biology Experiments results.

Design and Development of Virtual Reactivity System for PWR

International Nuclear Information System (INIS)

Anwar, M. I.

2012-01-01

The reactivity monitoring and investigation is an important mean to ensure the safety operation of a nuclear power plant. But the reactivity of the nuclear reactor usually cannot be directly measured. It should be computed with certain estimation method. In this thesis, an effort has been made using an artificial neural network and highly fluctuating experimental data for predicting the total reactivity of the nuclear reactor based on all components of net reactivity. This virtual reactivity system is designed by taking advantage of neural network's nonlinear mapping capability. Based on analysis of the reactivity contributing factors, several neural network models are built separately for control rod, boron, poisons, fuel Doppler Effect and moderator effect. Extensive simulation and validation tests for PWR show that satisfied results have been obtained with the proposed approach. It presents a new idea to estimate the PWR's reactivity using artificial intelligence. All the design and simulation work is carried out in MATLAB and a real time programming environment is chosen for the computation and prediction of reactivity. (author)

Investigating the effects of different physical and chemical stress ...

African Journals Online (AJOL)

2018-04-09

Apr 9, 2018 ... bacteria from extreme physical and chemical stress conditions. Additionally .... by inducing stress response genes, become more tolerant phenotypes ..... biofilm, monochloramine is more effective than free chlorine over long ...

Evaluation of reactivity shutdown margin for nuclear fuel reload optimization

International Nuclear Information System (INIS)

Engrand, P.; Wong, H. I.; Maldonado, G.I.

1996-01-01

The FORMOSA-P code is a nuclear fuel management optimization package which combines simulated annealing (SA) and nodal generalized perturbation theory (GPT). Recent studies at Electricite de France have produced good results for power peaking minimizations under multiple limiting control rod configurations. However, since the reactivity shutdown margin is not explicitly treated as an objective or constraint function, then any optimal loading patterns (LPs) are not guaranteed to yield an adequate shutdown margin (SDM). This study describes the implementation of the SDM calculation within a FORMOSA-P optimization. Maintaining all additional computational requirements to a minimum was a key consideration. (authors). 4 refs., 2 figs

Magnetic nanoparticles: reactive oxygen species generation and potential therapeutic applications

Science.gov (United States)

Mai, Trang; Hilt, J. Zach

2017-07-01

Magnetic nanoparticles have been demonstrated to produce reactive oxygen species (ROS), which play a major role in various cellular pathways, via Fenton and Haber-Weiss reaction. ROS act as a double-edged sword inside the body. At normal conditions, the generation of ROS is in balance with their elimination by scavenger systems, and they can promote cell proliferation as well as differentiation. However, at an increased level, they can cause damages to protein, lead to cellular apoptosis, and contribute to many diseases including cancer. Many recent studies proposed a variety of strategies to either suppress toxicity of ROS generation or exploit the elevated ROS levels for cancer therapy.

Nitrenes, carbenes, diradicals, and ylides. Interconversions of reactive intermediates.

Science.gov (United States)

Wentrup, Curt

2011-06-21

Rearrangements of aromatic and heteroaromatic nitrenes and carbenes can be initiated with either heat or light. The thermal reaction is typically induced by flash vacuum thermolysis, with isolation of the products at low temperatures. Photochemical experiments are conducted either under matrix isolation conditions or in solution at ambient temperature. These rearrangements are usually initiated by ring expansion of the nitrene or carbene to a seven-membered ring ketenimine, carbodiimide, or allene (that is, a cycloheptatetraene or an azacycloheptatetraene when a nitrogen is involved). Over the last few years, we have found that two types of ring opening take place as well. Type I is an ylidic ring opening that yields nitrile ylides or diazo compounds as transient intermediates. Type II ring opening produces either dienylnitrenes (for example, from 2-pyridylnitrenes) or 1,7-(1,5)-diradicals (such as those formed from 2-quinoxalinylnitrenes), depending on which of these species is better stabilized by resonance. In this Account, we describe our achievements in elucidating the nature of the ring-opened species and unraveling the connections between the various reactive intermediates. Both of these ring-opening reactions are found, at least in some cases, to dominate the subsequent chemistry. Examples include the formation of ring-opened ketenimines and carbodiimides, as well as the ring contraction reactions that form five-membered ring nitriles (such as 2- and 3-cyanopyrroles from pyridylnitrenes, N-cyanoimidazoles from 2-pyrazinyl and 4-pyrimidinylnitrenes, N-cyanopyrazoles from 2-pyrimidinylnitrenes and 3-pyridazinylnitrenes, and so forth). The mechanisms of formation of the open-chain and ring-contraction products were unknown at the onset of this study. In the course of our investigation, several reactions with three or more consecutive reactive intermediates have been unraveled, such as nitrene, seven-membered cyclic carbodiimide, and open-chain nitrile ylide

7-N-Acetylcysteine-pyrrole conjugate-A potent DNA reactive metabolite of pyrrolizidine alkaloids.

Science.gov (United States)

He, Xiaobo; Ma, Liang; Xia, Qingsu; Fu, Peter P

2016-10-01

Plants containing pyrrolizidine alkaloids (PAs) are widespread throughout the world and are the most common poisonous plants affecting livestock, wildlife, and humans. PAs require metabolic activation to form reactive dehydropyrrolizidine alkaloids (dehydro-PAs) that are capable of alkylating cellular DNA and proteins, form (±)-6,7-dihydro-7-hydroxy-1-hydroxymethyl-5H-pyrrolizine (DHP)-DNA and DHP-protein adducts, and lead to cytotoxicity, genotoxicity, and tumorigenicity. In this study, we determined that the metabolism of riddelliine and monocrotaline by human and rat liver microsomes in the presence of N-acetylcysteine both produced 7-N-acetylcysteine-DHP (7-NAC-DHP) and DHP. Reactions of 7-NAC-DHP with 2'-deoxyguanosine (dG), 2'-deoxyadenosine (dA), and calf thymus DNA in aqueous solution followed by enzymatic hydrolysis yielded DHP-dG and/or DHP-dA adducts. These results indicate that 7-NAC-DHP is a reactive metabolite that can lead to DNA adduct formation. Copyright © 2016. Published by Elsevier B.V.

7-N-Acetylcysteine-pyrrole conjugate—A potent DNA reactive metabolite of pyrrolizidine alkaloids

Directory of Open Access Journals (Sweden)

Xiaobo He

2016-10-01

Full Text Available Plants containing pyrrolizidine alkaloids (PAs are widespread throughout the world and are the most common poisonous plants affecting livestock, wildlife, and humans. PAs require metabolic activation to form reactive dehydropyrrolizidine alkaloids (dehydro-PAs that are capable of alkylating cellular DNA and proteins, form (±-6,7-dihydro-7-hydroxy-1-hydroxymethyl-5H-pyrrolizine (DHP-DNA and DHP-protein adducts, and lead to cytotoxicity, genotoxicity, and tumorigenicity. In this study, we determined that the metabolism of riddelliine and monocrotaline by human and rat liver microsomes in the presence of N-acetylcysteine both produced 7-N-acetylcysteine-DHP (7-NAC-DHP and DHP. Reactions of 7-NAC-DHP with 2′-deoxyguanosine (dG, 2′-deoxyadenosine (dA, and calf thymus DNA in aqueous solution followed by enzymatic hydrolysis yielded DHP-dG and/or DHP-dA adducts. These results indicate that 7-NAC-DHP is a reactive metabolite that can lead to DNA adduct formation.

Quantitation of cutaneous inflammation induced by reactive species generated by UV-visible irradiation of rose bengal

International Nuclear Information System (INIS)

Ranadive, N.S.; Menon, I.A.; Shirwadkar, S.; Persad, S.D.

1989-01-01

The present studies were undertaken to quantitate the initial inflammatory response produced by the photo-generated reactive species in rabbit skin. Rose bengal (RB), a photosensitizer dye, was injected into the skin sites at various concentrations and exposed to UV-visible light for 30-120 min. The increase in vascular permeability and the accumulation of PMNs were investigated using 125I-labeled albumin and 51Cr-labeled PMNs. RB at a concentration of 1 nmol with 120-min exposure to light enhanced vascular permeability by 3.7 times and accumulation of PMNs by 3.3 times. As low as 0.01 nmol of RB produced discernible effects. beta-Carotene (0.1 nmole) inhibited the inflammatory response by 75-100%, suggesting that the reactive species involved in this response was predominantly singlet oxygen. The increase in vascular permeability was inhibited by 48-70% by 25 micrograms of chlorpheniramine maleate. It is therefore suggested that histamine plays a major role in the initial vascular response. The studies demonstrate that this rabbit model is suitable for the quantitation of photoinduced inflammatory response which is not observable by gross anatomic procedures

Quantitation of cutaneous inflammation induced by reactive species generated by UV-visible irradiation of rose bengal

Energy Technology Data Exchange (ETDEWEB)

Ranadive, N.S.; Menon, I.A.; Shirwadkar, S.; Persad, S.D. (Univ. of Toronto, Ontario (Canada))

1989-10-01

The present studies were undertaken to quantitate the initial inflammatory response produced by the photo-generated reactive species in rabbit skin. Rose bengal (RB), a photosensitizer dye, was injected into the skin sites at various concentrations and exposed to UV-visible light for 30-120 min. The increase in vascular permeability and the accumulation of PMNs were investigated using 125I-labeled albumin and 51Cr-labeled PMNs. RB at a concentration of 1 nmol with 120-min exposure to light enhanced vascular permeability by 3.7 times and accumulation of PMNs by 3.3 times. As low as 0.01 nmol of RB produced discernible effects. beta-Carotene (0.1 nmole) inhibited the inflammatory response by 75-100%, suggesting that the reactive species involved in this response was predominantly singlet oxygen. The increase in vascular permeability was inhibited by 48-70% by 25 micrograms of chlorpheniramine maleate. It is therefore suggested that histamine plays a major role in the initial vascular response. The studies demonstrate that this rabbit model is suitable for the quantitation of photoinduced inflammatory response which is not observable by gross anatomic procedures.

Quantitative reactive modeling and verification.

Science.gov (United States)

Henzinger, Thomas A

Formal verification aims to improve the quality of software by detecting errors before they do harm. At the basis of formal verification is the logical notion of correctness , which purports to capture whether or not a program behaves as desired. We suggest that the boolean partition of software into correct and incorrect programs falls short of the practical need to assess the behavior of software in a more nuanced fashion against multiple criteria. We therefore propose to introduce quantitative fitness measures for programs, specifically for measuring the function, performance, and robustness of reactive programs such as concurrent processes. This article describes the goals of the ERC Advanced Investigator Project QUAREM. The project aims to build and evaluate a theory of quantitative fitness measures for reactive models. Such a theory must strive to obtain quantitative generalizations of the paradigms that have been success stories in qualitative reactive modeling, such as compositionality, property-preserving abstraction and abstraction refinement, model checking, and synthesis. The theory will be evaluated not only in the context of software and hardware engineering, but also in the context of systems biology. In particular, we will use the quantitative reactive models and fitness measures developed in this project for testing hypotheses about the mechanisms behind data from biological experiments.

α-Diazo-β-ketonitriles: uniquely reactive substrates for arene and alkene cyclopropanation.

Science.gov (United States)

Nani, Roger R; Reisman, Sarah E

2013-05-15

An investigation of the intramolecular cyclopropanation reactions of α-diazo-β-ketonitriles is reported. These studies reveal that α-diazo-β-ketonitriles exhibit unique reactivity in their ability to undergo arene cyclopropanation reactions; other similar acceptor-acceptor-substituted diazo substrates instead produce mixtures of C-H insertion and dimerization products. α-Diazo-β-ketonitriles also undergo highly efficient intramolecular cyclopropanation of tri- and tetrasubstituted alkenes. In addition, the α-cyano-α-ketocyclopropane products are demonstrated to serve as substrates for SN2, SN2', and aldehyde cycloaddition reactions.

MTR fuel element burn-up measurements by the reactivity method

International Nuclear Information System (INIS)

Zuniga, A.; Cuya, T.R.; Ravnik, M.

2003-01-01

Fuel element burn-up was measured by the reactivity method in the 10 MW Peruvian MTR reactor RP-10. The main purpose of the experiment was testing the reactivity method for an MTR reactor as the reactivity method was originally developed for TRIGA reactors. The reactivity worth of each measured fuel element was measured in its original core position in order to measure the burn-up of the fuel elements that were part of the experimental core. The burn-up of each measured fuel element was derived by interpolating its reactivity worth from the reactivity worth of two reference fuel elements of known burn-up, whose reactivity worth was measured in the position of the measured fuel element. The accuracy of the method was improved by separating the reactivity effect of burn-up from the effect of the position in the core. The results of the experiment showed that the modified reactivity method for fuel element burn-up determination could be applied also to MTR reactors. (orig.)

Immune reactivity of candidate reference materials

NARCIS (Netherlands)

Fernandez-Rivas, Montserrat; Aalbers, Marja; Fötisch, Kay; de Heer, Pleuni; Notten, Silla; Vieths, Stefan; van Ree, Ronald

2006-01-01

Immune reactivity is a key issue in the evaluation of the quality of recombinant allergens as potential reference materials. Within the frame of the CREATE project, the immune reactivity of the natural and recombinant versions of the major allergens of birch pollen (Bet v 1), grass pollen (Phl p 1

An autonomous organic reaction search engine for chemical reactivity

Science.gov (United States)

Dragone, Vincenza; Sans, Victor; Henson, Alon B.; Granda, Jaroslaw M.; Cronin, Leroy

2017-06-01

The exploration of chemical space for new reactivity, reactions and molecules is limited by the need for separate work-up-separation steps searching for molecules rather than reactivity. Herein we present a system that can autonomously evaluate chemical reactivity within a network of 64 possible reaction combinations and aims for new reactivity, rather than a predefined set of targets. The robotic system combines chemical handling, in-line spectroscopy and real-time feedback and analysis with an algorithm that is able to distinguish and select the most reactive pathways, generating a reaction selection index (RSI) without need for separate work-up or purification steps. This allows the automatic navigation of a chemical network, leading to previously unreported molecules while needing only to do a fraction of the total possible reactions without any prior knowledge of the chemistry. We show the RSI correlates with reactivity and is able to search chemical space using the most reactive pathways.

Formation of novel reactive intermediate by electron-laser dual beam irradiation

International Nuclear Information System (INIS)

Ishida, Akito; Takamuku, Setsuo

1992-01-01

The pulse radiolysis system of the Institute of Scientific and Industrial Research, Osaka University, (ISIR) has been progressed to observe a highly reactive species, which is produced by successive irradiation of electron and laser or of CW-UV-light and electron. The dual beam irradiation system, which consists of the beam synchronization system, the optical alignment, and the measurement system, is described in detail. Dual beam irradiation studies on 2-methylbenzophenone and some compounds with a C=N bond have been carried out by use of this system. Pulse radiolysis of 2-methylbenzophenone in benzene induced formation of an unstable photoenol via the triplet state, which was irradiated by a visible laser pulse to give dihydroanthrone. Pulse radiolysis of syn-benzalaniline and a nitrileylide in 2-methyltetrahydrofuran, which were produced by steady state photoirradiation at low temperature, enabled us to observe their very unstable radical anions. (author)

Mitochondrial Signaling in Plants Under Hypoxia: Use of Reactive Oxygen Species (ROS) and Reactive Nitrogen Species (RNS)

DEFF Research Database (Denmark)

Hebelstrup, Kim; Møller, Ian Max

2015-01-01

Hypoxia commonly occurs in roots in water-saturated soil and in maturing and germinating seeds. We here review the role of the mitochondria in the cellular response to hypoxia with an emphasis on the turnover of Reactive Oxygen Species (ROS) and Reactive Nitrogen Species (RNS) and their potential...

Permeable reactive barriers for pollutant removal from groundwater

International Nuclear Information System (INIS)

Simon, F.G.; Meggyes, T.

2001-01-01

The removal of pollutants from the groundwater using permeable reactive barriers is a novel in-situ groundwater remediation technology. The most relevant decontamination processes used are chemical reduction, oxidation, precipitation and sorption, for which examples are given. Some common organic pollutants are halogenated hydrocarbons, aromatic and nitroaromatic compounds which can be treated in reactive barriers successfully. Lead, chromium and, in particular, uranium are dealt with in great detail among inorganic pollutants because of their occurrence in many European countries. Construction methods for cut-off walls and reactive barriers exhibit similar features. Apart from conventional methods, drilling, deep soil mixing, jet technology, arrays of wells, injected systems and biobarriers are applied to construct permeable reactive barriers. Permeable reactive barriers bear great potential for the future in remediation engineering. (orig.)

Reactive wetting by liquid sodium on thin Au platin

International Nuclear Information System (INIS)

Kawaguchi, Munemichi; Hamada, Hirotsugu

2014-01-01

For practical use of an under-sodium viewer, the behavior of sodium wetting is investigated by modeling the reactive and non-reactive wetting of metallic-plated steels by liquid sodium to simulate sodium wetting. The non-reactive wetting simulation results showed good agreement with Tanner's law, in which the time dependencies of the droplet radius and contact angle are expressed as R N ∝ t 1/10 and θ∝ t -3/10 , respectively; therefore, the model was considered suitable for the simulation. To simulate reactive wetting, the model of fluid flow induced by the interfacial reaction was incorporated into the simulation of non-reactive wetting. The reactive wetting simulation results, such as the behavior of the precursor liquid film and central droplet, showed good agreement with sodium wetting experiments using thin Au plating at 250°C. An important result of the reactive wetting simulation is that the gradient of the reaction energy at the interface appeared on the new interface around the triple line, and that fluid flow was induced. This interfacial reactivity during sodium wetting of thin Au plating was enhanced by the reaction of sodium and nickel oxide through pinholes in the plating. (author)

Instructions for applying inverse method for reactivity measurement

International Nuclear Information System (INIS)

Milosevic, M.

1988-11-01

This report is a brief description of the completed method for reactivity measurement. It contains description of the experimental procedure needed instrumentation and computer code IM for determining reactivity. The objective of this instructions manual is to enable experiments and reactivity measurement on any critical system according to the methods adopted at the RB reactor

Quantitative characterization of silicon- and aluminium oxynitride films produced by reactive dc-magnetron sputtering

International Nuclear Information System (INIS)

Dreer, S.

2000-05-01

The deposition of aluminum and silicon oxynitride films by reactive dc-magnetron sputtering was systematically planned by design of experiments, carried out and evaluated with the application of specialized statistics software. The influence of the deposition parameters on the resulting films was evaluated by multiple regression analysis. With the obtained data a model of the deposition process for the quantitative prediction of the deposition parameters necessary to obtain films with desired composition was built. This is also of technological importance, since the physical properties of the films strongly depend on their composition. Furthermore, the long term repeatability of the deposition process was implemented into the model. A precise and economic way for quantitative bulk analysis of silicon/aluminum, oxygen and nitrogen based on EPMA was presented and the use of data gained by the latter method is discussed for the calculation of relative sensitivity factors for SIMS and hf-SNMS. Advantages and disadvantages of SIMS, hf-SNMS, hf-GD-OES, and sputter AES were compared. The combination FT-IR/EPMA/SIMS at present offers the best possibility for a quantitative bulk and in depth distribution analysis of such films in the range of 20 to 1000 nm thickness. The films were also characterized by XRD and PAA. The refractive index and the growth rate of the films were determined by spectroscopic ellipsometry. With indentation by a nano hardness tester the hardness and the Young's modulus of the films were obtained. The results of these measurements were evaluated by statistical software. The dependencies of the physical properties on the deposition parameters and on the film thickness were evaluated and quantified. Furthermore, the dependencies of the physical properties on the film composition represented by the oxygen content were evaluated. (author)

Studies of the reactivity effects of hydrogenous material in a sodium cooled fast reactor

International Nuclear Information System (INIS)

Ingram, D.; Sweet, D.W.

1979-01-01

The reactivity effects of hydrogenous substances, such as the oil used in the primary coolant pumps, which could enter the core of a fast reactor in a hypothetical accident, have been studied in a series of experiments and calculations. Measurements to study the influence of the density of the hydrogen and its location on reactivity were made in two assemblies in the zero power reactor ZEBRA. The first of these was similar in size to PFR and the second was the large BZB assembly of the BIZET programme. The results of this work have been compared with calculations using the FGL5 nuclear data library. Calculations for a 1200 MW (e) CFR have been made using three quantities of material (8, 40 and 160 Kg of hydrocarbon, equivalent to 10, 50 and 200 litres of oil). The calculations have used different geometrical models and hydrocarbon distributions and have explored the influence of core temperature, fuel burn-up and the presence of control rods to estimate the maximum reactivity changes that can be obtained. The results have been analysed in terms of components of the change in neutron balance produced by the material and uncertainties in these have been derived from the ZEBRA work. (author)

Fuel Temperature Coefficient of Reactivity

Energy Technology Data Exchange (ETDEWEB)

Loewe, W.E.

2001-07-31

A method for measuring the fuel temperature coefficient of reactivity in a heterogeneous nuclear reactor is presented. The method, which is used during normal operation, requires that calibrated control rods be oscillated in a special way at a high reactor power level. The value of the fuel temperature coefficient of reactivity is found from the measured flux responses to these oscillations. Application of the method in a Savannah River reactor charged with natural uranium is discussed.

Competitive adsorption of Reactive Orange 16 and Reactive Brilliant Blue R on polyaniline/bacterial extracellular polysaccharides composite-A novel eco-friendly polymer

Energy Technology Data Exchange (ETDEWEB)

Janaki, V. [Department of Chemistry, Periyar University, Salem 636011, Tamil Nadu (India); Vijayaraghavan, K. [Singapore-Delft Water Alliance, National University of Singapore, 117577 (Singapore); Ramasamy, A.K. [Department of Chemistry, Periyar University, Salem 636011, Tamil Nadu (India); Lee, Kui-Jae [Division of Biotechnology, Advanced Institute of Environment and Bioscience, College of Environmental and Bioresource Sciences, Chonbuk National University, Iksan 570752 (Korea, Republic of); Oh, Byung-Taek, E-mail: btoh@jbnu.ac.kr [Division of Biotechnology, Advanced Institute of Environment and Bioscience, College of Environmental and Bioresource Sciences, Chonbuk National University, Iksan 570752 (Korea, Republic of); Kamala-Kannan, Seralathan, E-mail: kannan@jbnu.ac.kr [Division of Biotechnology, Advanced Institute of Environment and Bioscience, College of Environmental and Bioresource Sciences, Chonbuk National University, Iksan 570752 (Korea, Republic of)

2012-11-30

Highlights: Black-Right-Pointing-Pointer Competitive adsorption of reactive dyes onto polyaniline/bacterial extracellular polysaccharides composite. Black-Right-Pointing-Pointer The composite have functional groups of both polyaniline and bacterial extracellular polysaccharides. Black-Right-Pointing-Pointer The presence of Reactive Brilliant Blue R diminished the uptake of Reactive Orange 16. Black-Right-Pointing-Pointer Electrostatic interaction was identified as a major mechanism in adsorption process. Black-Right-Pointing-Pointer Reactive Brilliant Blue R and Reactive Orange 16 adsorption was endothermic process. - Abstract: The performance of polyaniline/extracellular polymeric substances (Pn/EPS) composite as an adsorbent to remove the anionic reactive dyes, Reactive Brilliant Blue R (RBBR) and Reactive Orange 16 (RO), was investigated in single and binary systems. The pH{sub pzc} of Pn/EPS composite was calculated as 3.7 through potentiometric mass titration method. Electrostatic interaction between the dye anion and the nitrogen present in the polymer was identified as a major mechanism in adsorption process. Single component isotherms followed the Langmuir model with the maximum adsorption capacity of 0.5775 mmol g{sup -1} for RBBR and 0.4748 mmol g{sup -1} for RO. In binary system, both the reactive dye anions compete with each other and resulted in lower uptake. Binary adsorption data were interpreted well by the Sheindorf-Rehbun-Sheintuch equation as compared to extended Langmuir model with constant interaction factor. Kinetic analysis of single solute followed pseudo-first order model. Thermodynamic studies computed that RBBR and RO adsorption was endothermic, spontaneous, and feasible process.

Sensitivity analysis of reactive ecological dynamics.

Science.gov (United States)

Verdy, Ariane; Caswell, Hal

2008-08-01

Ecological systems with asymptotically stable equilibria may exhibit significant transient dynamics following perturbations. In some cases, these transient dynamics include the possibility of excursions away from the equilibrium before the eventual return; systems that exhibit such amplification of perturbations are called reactive. Reactivity is a common property of ecological systems, and the amplification can be large and long-lasting. The transient response of a reactive ecosystem depends on the parameters of the underlying model. To investigate this dependence, we develop sensitivity analyses for indices of transient dynamics (reactivity, the amplification envelope, and the optimal perturbation) in both continuous- and discrete-time models written in matrix form. The sensitivity calculations require expressions, some of them new, for the derivatives of equilibria, eigenvalues, singular values, and singular vectors, obtained using matrix calculus. Sensitivity analysis provides a quantitative framework for investigating the mechanisms leading to transient growth. We apply the methodology to a predator-prey model and a size-structured food web model. The results suggest predator-driven and prey-driven mechanisms for transient amplification resulting from multispecies interactions.

Cooling-water chlorination: the kinetics of chlorine, bromine, and ammonia in sea water

International Nuclear Information System (INIS)

Johnson, J.D.; Inman, G.W. Jr.; Trofe, T.W.

1982-11-01

The major inorganic reaction pathways for the chlorination of saline waters were measured by a variety of techniques including: (1) amperometric titration, (2) amperometric membrane covered electrode, (3) uv spectrophotometry, (4) conventional kinetics methods for slow reactions, and (5) stopped-flow kinetics measurements with a microcomputer data acquisition system. The major reactions studied were: (1) the competitive reactions of ammonia and bromide ion with hypochlorous acid, (2) bromide oxidation by hypochlorous acid, (3) monochloramine formation in sea water, (4) monobromamine formation and subsequent disproportionation to form dibromamine, and (5) monochloramine oxidation of bromide to form bromochloramine. Reaction rates were determined in sodium chloride and sea water as a function of reactant concentration, pH, salinity, and ammonia concentration. Rate constants and corresponding rate laws and mechanisms were developed for each reaction

Radiation enhanced reactivation of nuclear replicating mammalian viruses

International Nuclear Information System (INIS)

Bockstahler, L.E.; Lytle, C.D.

1977-01-01

When CV-1 monkey kidney cells were UV-irradiated (0 to 18 J/m 2 ) or X-irradiated (0 to 10 krads) before infection with UV-irradiated simian adenovirus 7 (SA7) or simian virus 40 (SV40), increases in the infectivity of these nuclear replicating viruses as measured by plaque formation were observed. These radiation enhanced reactivations, UV enhanced reactivation (UVER) and X-ray enhanced reactivation (X-ray ER), occurred both when virus infection immediately followed irradiation of the cells (except for X-ray ER with SA7) and when virus infection was delayed until 3 to 5 days after cell irradiation. While there was little difference in the levels of reactivation of UV-irradiated SV40 between immediate and delayed infection, delayed infection resulted in higher levels of reactivation of SA7. X-ray enhanced reactivation of UV-irradiated Herpes simplex virus persisted for several days but did not increase. Thus, X-ray enhanced and UV enhanced reactivations of these mammalian viruses were relatively long-lived effects. Essentially no UVER or X-ray ER was found in CV-1 cells for either immediate or delayed infection with UV-irradiated vaccinia virus or poliovirus, both of which replicate in the cell cytoplasm. These results suggest UVER and X-ray ER in mammalian cells may be restricted to viruses which are replicated in the cell nucleus. (author)

Intercomparison of the comparative reactivity method (CRM) and pump-probe technique for measuring total OH reactivity in an urban environment

Science.gov (United States)

Hansen, R. F.; Blocquet, M.; Schoemaecker, C.; Léonardis, T.; Locoge, N.; Fittschen, C.; Hanoune, B.; Stevens, P. S.; Sinha, V.; Dusanter, S.

2015-10-01

The investigation of hydroxyl radical (OH) chemistry during intensive field campaigns has led to the development of several techniques dedicated to ambient measurements of total OH reactivity, which is the inverse of the OH lifetime. Three techniques are currently used during field campaigns, including the total OH loss rate method, the pump-probe method, and the comparative reactivity method. However, no formal intercomparison of these techniques has been published so far, and there is a need to ensure that measurements of total OH reactivity are consistent among the different techniques. An intercomparison of two OH reactivity instruments, one based on the comparative reactivity method (CRM) and the other based on the pump-probe method, was performed in October 2012 in a NOx-rich environment, which is known to be challenging for the CRM technique. This study presents an extensive description of the two instruments, the CRM instrument from Mines Douai (MD-CRM) and the pump-probe instrument from the University of Lille (UL-FAGE), and highlights instrumental issues associated with the two techniques. It was found that the CRM instrument used in this study underestimates ambient OH reactivity by approximately 20 % due to the photolysis of volatile organic compounds (VOCs) inside the sampling reactor; this value is dependent on the position of the lamp within the reactor. However, this issue can easily be fixed, and the photolysis of VOCs was successfully reduced to a negligible level after this intercomparison campaign. The UL-FAGE instrument may also underestimate ambient OH reactivity due to the difficulty to accurately measure the instrumental zero. It was found that the measurements are likely biased by approximately 2 s-1, due to impurities in humid zero air. Two weeks of ambient sampling indicate that the measurements performed by the two OH reactivity instruments are in agreement, within the measurement uncertainties for each instrument, for NOx mixing ratios

Structure and Reactivity of Zeolite- and Carbon-Supported Catalysts for the Oxidative Carbonylation of Alcohols

OpenAIRE

Briggs, Daniel Neal

2010-01-01

AbstractStructure and Reactivity of Zeolite- and Carbon-Supported Catalysts for the Oxidative Carbonylation of AlcoholsbyDaniel Neal BriggsDoctor of Philosophy in Chemical EngineeringUniversity of California, BerkeleyProfessor Alexis T. Bell, Chair The oxidative carbonylation of alcohols to produce dialkyl carbonates is a process that takes place commercially in a slurry of cuprous chloride in the appropriate alcohol. While this process is chemically efficient, it incurs costs in terms of ene...

(3) Melatonin Protects Oocytes and Granulosa Cells from Reactive Oxygen Species during the Ovulatory Process

OpenAIRE

田村, 博史; Hiroshi, TAMURA; 山口大学大学院医学系研究科産科婦人科学; Department of Obstetrics and Gynecology, Yamaguchi University Graduate School of Medicine

2009-01-01

Reactive oxygen species (ROS) are produced within the follicle especially during the ovulatory process. ROS play a physiological role in the process of ovulation, e.g. follicle rapture. However, excessive amount of ROS causes oxidative stress and damages oocytes and luteinized granulosa cells. On the other hand, antioxidant defense systems including superoxide dismutase (SOD) or glutathione (GSH) are present in follicles. The balance between ROS and antioxidants within the follicle seems to b...

Steam hydration-reactivation of FBC ashes for enhanced in situ desulphurization

Energy Technology Data Exchange (ETDEWEB)

Fabio Montagnaro; Marianna Nobili; Antonio Telesca; Gian Lorenz Valenti; Edward J. Anthony; Piero Salatino [Universita degli Studi di Napoli Federico II, Napoli (Italy). Dipartimento di Chimica

2009-06-15

Bed and fly ashes originating from industrial-scale fluidized bed combustors (FBCs) were steam hydrated to produce sorbents suitable for further in situ desulphurization. Samples of the hydrated ash were characterized by X-ray diffraction analysis, scanning electron microscopy and porosimetry. Bed ashes were hydrated in a pressure bomb for 30 and 60 min at 200{sup o}C and 250{sup o}C. Fly ash was hydrated in an electrically heated tubular reactor for 10 and 60 min at 200{sup o}C and 300{sup o}C. The results were interpreted by considering the hydration process and the related development of accessible porosity suitable for resulphation. The performance of the reactivated bed ash as sulphur sorbent improved with a decrease of both the hydration temperature and time. For reactivated fly ash, more favourable porosimetric features were observed at longer treatment times and lower hydration temperatures. Finally, it was shown that an ashing treatment (at 850{sup o}C for 20 min) promoted a speeding up of the hydration process and an increase in the accessible porosity. 36 refs., 6 figs., 2 tabs.

Reactivity analysis of core distortion effects in the FFTF

International Nuclear Information System (INIS)

Knutson, B.J.

1982-01-01

An improved technique for evaluating core distortion reactivity effects was developed using reactivity analyses of two core geometry models (R-Z and HEX). This technique is incorporated into a new processor code called CORDIS. The advantages of this technique over existing reactivity models are that is preserves core heterogeneity, provides a control rod insertion effect model, uses row-dependent axial shape functions, and provides a flexible and cost efficient core distortion reactivity analysis method

Integrated reactive self-assessment for programmatic learning

International Nuclear Information System (INIS)

Corcoran, W.R.

1996-01-01

This paper presents a generalized method for using reactive self-assessment. The application is to programmatic learning involving the integration of reactive self-assessment results over a period of time. This paper also presents some of the results of one application of the process. Self-assessment, in general, is the assessment conducted or sponsored by an individual or organization of its own activities for the purpose of detecting improvement opportunities, either of the corrective or the enhancement types. Reactive self-assessment is a self-assessment activity conducted in reaction to a shortfall event. An integrative reactive self-assessment is a self-assessment that integrates a set of reactive self-assessment results. Programmatic learning is increasing the knowledge base in a program area. Self-assessment, in general, and reactive self-assessment, in particular, are required by federal quality requirements. One such program area is nuclear power plant testing, which is also required by federal quality requirements. Any program area could have been selected, but this one was selected because it was involved in the Chernobyl accident, the most consequential nuclear power accident up until the time of this writing. Other consequential accidents involving nuclear power plant testing were the Browns Ferry fire and the Salem overspeed event. (The author, of course, does not conduct nuclear power plant testing but is doing a self-assessment as if he were acting for an organization that did testing.)

Chemical reactivity of alkali lignin modified with laccase

International Nuclear Information System (INIS)

Sun, Yong; Qiu, Xueqing; Liu, Yunquan

2013-01-01

The modification of alkali lignin with laccase was investigated. The structural change of lignin was analyzed. The sulfonation reactivity was measured by the content of sulfonic group. The results showed the sulfonation reactivity increased to some extent under the condition of atmosphere pressure, but decreased under the condition of 0.3 MPa oxygen pressure. The analysis of Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance (NMR) and gel permeation chromatography (GPC) showed the cleavage of various ether linkages and demethylation took place in the structure of lignin to certain extent during modification with laccase, which contributed to the improvement of sulfonation reactivity. Under the condition of 0.3 MPa oxygen pressure, the ratio of s/g (guaiacyl/syringyl) increased after modification, which reduced the sulfonation reactivity of lignin. Simultaneously partial polymerization reaction, such as 4-O-5′, β-5, 5-5 and other reaction in the aromatic ring decreased the activity sites of C 2 , C 5 and C 6 . Abundant polymerization reaction of α-O increased steric hindrance of C 2 and C 6 in aromatic ring, resulting in low sulfonation reactivity of lignin. -- Highlights: ► The modification of alkali lignin with laccase was investigated. ► The sulfonation reactivity increased under the condition of atmosphere pressure. ► More content of guaiacyl and hydroxy, the less content of methoxyl, syringyl can enhance the sulfonation reactivity of lignin. ► Partial moieties polymerized each other with α-O linkgages during treatment with laccase under oxygen pressure. ► The steric hindrance on C 2 and C 6 in aromatic ring resulted in low sulfonation reaction reactivity of lignin

Using the general-purpose reactivity indicator: challenging examples.

Science.gov (United States)

Anderson, James S M; Melin, Junia; Ayers, Paul W

2016-03-01

We elucidate the regioselectivity of nucleophilic attack on substituted benzenesulfonates, quinolines, and pyridines using a general-purpose reactivity indicator (GPRI) for electrophiles. We observe that the GPRI is most accurate when the incoming nucleophile resembles a point charge. We further observe that the GPRI often chooses reactive "dead ends" as the most reactive sites as well as sterically hindered reactive sites. This means that care must be taken to remove sites that are inherently unreactive. Generally, among sites where reactions actually occur, the GPRI identifies the sites in the molecule that lead to the kinetically favored product(s). Furthermore, the GPRI can discern which sites react with hard reagents and which sites react with soft reagents. Because it is currently impossible to use the mathematical framework of conceptual DFT to identify sterically inaccessible sites and reactive dead ends, the GPRI is primarily useful as an interpretative, not a predictive, tool.

Observations of oxidation products above a forest imply biogenic emissions of very reactive compounds

Directory of Open Access Journals (Sweden)

R. Holzinger

2005-01-01

Full Text Available Vertical gradients of mixing ratios of volatile organic compounds have been measured in a Ponderosa pine forest in Central California (38.90° N, 120.63° W, 1315m. These measurements reveal large quantities of previously unreported oxidation products of short lived biogenic precursors. The emission of biogenic precursors must be in the range of 13-66µmol m-2h-1 to produce the observed oxidation products. That is 6-30 times the emissions of total monoterpenes observed above the forest canopy on a molar basis. These reactive precursors constitute a large fraction of biogenic emissions at this site, and are not included in current emission inventories. When oxidized by ozone they should efficiently produce secondary aerosol and hydroxyl radicals.

Suicidal ideation is associated with individual differences in prescription opioid craving and cue-reactivity among chronic pain patients.

Science.gov (United States)

Garland, Eric L; Riquino, Michael R; Priddy, Sarah E; Bryan, Craig J

2017-01-01

Given that chronic pain patients experience significant rates of suicidal ideation and suicide attempts, access to prescription opioids compounds the risk of death by suicide. These patients may experience heightened opioid craving and exhibit increased cue-reactivity to stimuli associated with past opioid use when suicidal ideation produces negative affective states. Because both opioids and suicidal behavior are used to alleviate emotional and physical pain through a process of negative reinforcement, elucidating factors that mediate this association may yield insight into suicide risk among chronic pain patients. This study examined the relationship between suicidal ideation and opioid craving and cue-reactivity, and tested opioid self-medication as a mediator of associations between those factors after controlling for the impact of pain severity. A sample of 115 chronic pain patients provided demographic and clinical information on the Obsessive Compulsive Drug Use Scale, the Current Opioid Misuse Measure, and the Brief Pain Inventory before completing an opioid dot probe task in which heart rate variability was recorded. As hypothesized, suicidal ideation was positively correlated with subjective opioid craving and physiological cue-reactivity. Self-medication significantly mediated the association between suicidal ideation, craving, and cue-reactivity. As opioids relieve the emotional pain linked with suicidal thoughts, chronic pain patients with higher levels of suicidal ideation may experience more intense opioid craving and exhibit heightened physiological cue-reactivity when compared to patients with low levels of suicidal ideation.

Measuring Memory Reactivation With Functional MRI: Implications for Psychological Theory.

Science.gov (United States)

Levy, Benjamin J; Wagner, Anthony D

2013-01-01

Environmental cues often remind us of earlier experiences by triggering the reactivation of memories of events past. Recent evidence suggests that memory reactivation can be observed using functional MRI and that distributed pattern analyses can even provide evidence of reactivation on individual trials. The ability to measure memory reactivation offers unique and powerful leverage on theoretical issues of long-standing interest in cognitive psychology, providing a means to address questions that have proven difficult to answer with behavioral data alone. In this article, we consider three instances. First, reactivation measures can indicate whether memory-based inferences (i.e., generalization) arise through the encoding of integrated cross-event representations or through the flexible expression of separable event memories. Second, online measures of memory reactivation may inform theories of forgetting by providing information about when competing memories are reactivated during competitive retrieval situations. Finally, neural reactivation may provide a window onto the role of replay in memory consolidation. The ability to track memory reactivation, including at the individual trial level, provides unique leverage that is not afforded by behavioral measures and thus promises to shed light on such varied topics as generalization, integration, forgetting, and consolidation. © The Author(s) 2013.

The reactivity of natural phenols

Energy Technology Data Exchange (ETDEWEB)

Denisov, Evgenii T; Denisova, Taisa G [Institute of Problems of Chemical Physics, Russian Academy of Sciences, Chernogolovka, Moscow Region (Russian Federation)

2009-11-30

This review surveys physicochemical data of natural phenols published in recent years. The structures of some compounds of this class are given. A complete set of the dissociation energies of the O-H bonds for 71 natural phenols is presented. Kinetic characteristics of the reactions of peroxyl, alkyl and thiyl radicals with natural phenols, exchange reactions of phenoxyl radicals with phenols and reactions of phenoxyl radicals with lipids, hydroperoxides, cysteine and ascorbic acid are compiled and described systematically. The reactivity of phenols in radical reactions and the factors that determine the reactivity (the enthalpy of reaction, triplet repulsion, the electronegativities of atoms at the reaction centre, the presence of pi-electrons adjacent to the reaction centre, the radii of atoms at the reaction centre, steric hindrance, the force constants of the reacting bonds) are discussed. An important role of hydrogen bonding between surrounding molecules and the OH groups of natural phenols in decreasing their reactivities is noted.

Achieving high fusion reactivity in high poloidal beta discharges in TFTR

International Nuclear Information System (INIS)

Manuel, M.E.; Navratil, G.A.; Sabbagh, S.A.; Batha, S.; Bell, M.G.; Bell, R.; Budny, R.V.; Bush, C.E.; Cavallo, A.; Chance, M.S.; Cheng, C.Z.; Efthimion, P.C.; Fredrickson, E.D.; Fu, G.Y.; Hawryluk, R.J.; Janos, A.C.; Jassby, D.L.; Levinton, F.; Mikkelsen, D.R.; Manickam, J.; McCune, D.C.; McGuire, K.M.; Medley, S.S.; Mueller, D.; Nagayama, Y.; Owens, D.K.; Park, H.K.; Ramsey, A.T.; Stratton, B.C.; Synakowski, E.J.; Taylor, G.; Wieland, R.M.; Yamada, M.; Zarnstorff, M.C.: Zweben, S.; Kesner, J.; Marmar, E.; Snipes, J.; Terry, J.

1993-04-01

High poloidal beta discharges have been produced in TFTR that achieved high fusion reactivities at low plasma currents. By rapidly decreasing the plasma current just prior to high-power neutral beam injection, relatively peaked current profiles were created having high l i > 2, high Troyon-normalized beta, βN > 3, and high poloidal beta. β p ≥ 0.7 R/a. The global energy confinement time after the current ramp was comparable to supershots, and the combination of improved MHD stability and good confinement produced a new high εβ p high Q DD operating mode for TFTR. Without steady-state current profile control, as the pulse lengths of high βp discharges were extended, l i decreased, and the improved stability produced immediately after by the current ramp deteriorated. In four second, high εβ p discharges, the current profile broadened under the influence of bootstrap and beam-drive currents. When the calculated voltage throughout the plasma nearly vanished, MHD instabilities were observed with β N as low as 1.4. Ideal MHD stability calculations showed this lower beta limit to be consistent with theoretical expectations

Multiphase composition changes and reactive oxygen species formation during limonene oxidation in the new Cambridge Atmospheric Simulation Chamber (CASC)

Science.gov (United States)

Gallimore, Peter J.; Mahon, Brendan M.; Wragg, Francis P. H.; Fuller, Stephen J.; Giorio, Chiara; Kourtchev, Ivan; Kalberer, Markus

2017-08-01

The chemical composition of organic aerosols influences their impacts on human health and the climate system. Aerosol formation from gas-to-particle conversion and in-particle reaction was studied for the oxidation of limonene in a new facility, the Cambridge Atmospheric Simulation Chamber (CASC). Health-relevant oxidising organic species produced during secondary organic aerosol (SOA) formation were quantified in real time using an Online Particle-bound Reactive Oxygen Species Instrument (OPROSI). Two categories of reactive oxygen species (ROS) were identified based on time series analysis: a short-lived component produced during precursor ozonolysis with a lifetime of the order of minutes, and a stable component that was long-lived on the experiment timescale (˜ 4 h). Individual organic species were monitored continuously over this time using Extractive Electrospray Ionisation (EESI) Mass Spectrometry (MS) for the particle phase and Proton Transfer Reaction (PTR) MS for the gas phase. Many first-generation oxidation products are unsaturated, and we observed multiphase aging via further ozonolysis reactions. Volatile products such as C9H14O (limonaketone) and C10H16O2 (limonaldehyde) were observed in the gas phase early in the experiment, before reacting again with ozone. Loss of C10H16O4 (7-hydroxy limononic acid) from the particle phase was surprisingly slow. A combination of reduced C = C reactivity and viscous particle formation (relative to other SOA systems) may explain this, and both scenarios were tested in the Pretty Good Aerosol Model (PG-AM). A range of characterisation measurements were also carried out to benchmark the chamber against existing facilities. This work demonstrates the utility of CASC, particularly for understanding the reactivity and health-relevant properties of organic aerosols using novel, highly time-resolved techniques.

Wintertime Emissions from Produced Water Ponds

Science.gov (United States)

Evans, J.; Lyman, S.; Mansfield, M. L.

2013-12-01

surfaces. These compounds are highly reactive and, because of their relatively high water solubility, tend to concentrate in produced water. The average methanol emission rate from unfrozen pond surfaces was more than 100 mg m-2 h-1. Methanol, used as an antifreeze and anti-scaler in the oil and gas industry, is abundant during winter inversions in the Uintah Basin and may also be a significant precursor to ozone production. Total VOC and methanol emissions from produced water ponds during winter were estimated to be 178 and 83 tons month-1, respectively, for the entire Uintah Basin.

The Differences in Normative Beliefs among Schoolchildren with Reactive, Proactive, Reactive-Proactive Aggression, and without Aggression

OpenAIRE

Annis Lai Chu Fung

2015-01-01

This study is to fill up a research gap on examining the differences in normative beliefs (namely acceptance of weaknesses, acceptance of provoked aggression, and acceptance of unprovoked aggression) among different subtypes of aggressors and non-aggressors (reactive aggressors, proactive aggressors, reactive-proactive aggressors, and non-aggressors). 2,236 students (1,372 males and 864 females), aged from 11 to 18, completed a self-reported questionnaire. Results reveale...

Reactivity transient calculatios in research reactor

International Nuclear Information System (INIS)

Santos, R.S. dos

1986-01-01

A digital program for reactivity transient analysis in research reactor and cylindrical geometry was showed quite efficient when compared with methods and programs of the literature, as much in the solution of the neutron kinetics equation as in the thermohydraulic. An improvement in the representation of the feedback reactivity adopted on the program reduced markedly the computation time, with some accuracy. (Author) [pt

A preliminary high-pressure thermogravimetric study of combustion reactivity of a Collie coal char

Energy Technology Data Exchange (ETDEWEB)

Chan, Yii Leng; Zhang, Zhezi; Zhu, Mingming; Zhang, Dongke [Western Australia Univ., Crawley, WA (Australia). Centre for Energy (M473); Luan, Chao [Western Australia Univ., Crawley, WA (Australia). Centre for Energy (M473); Tsinghua Univ., Beijing (China). Inst. of Thermal Engineering; You, Changfu [Tsinghua Univ., Beijing (China). Inst. of Thermal Engineering

2013-07-01

The effect of pressure(up to 20 bar)on the reactivity of a char(150-160 {mu}m) produced from Western Australian Collie coal has been studied using a high-pressure thermogravimetric analyser (HP TGA). The pressure demonstrated a positive effect in enhancing char combustion reactivities.Kinetic parameters have been determined from the experimental data.The apparent reaction order was found to be approximately 0.7 and the apparent activation energies were 91.0 kJ/mol at atmospheric pressure and 1.5 kJ/mol at an elevated pressure(10 bar),indicating a shift in the control regimes of the reaction at elevated pressures.The lumped effect of the sample size, bulk diffusion,interparticle and intraparticle diffusion at the elevated pressures played an important role in reducing the mass transfer during the HP-TGA experimentation.Thus the activation energy calculated at elevated pressures may not represent the intrinsic activation energy of the char particles but the apparent values of the bulk of the samples.

The roles of ozone and zeolite on reactive dye degradation in electrical discharge reactors.

Science.gov (United States)

Peternel, L; Kusic, H; Koprivanac, N; Locke, B R

2006-05-01

In this study high voltage pulsed corona electrical discharge advanced oxidation processes (AOPs) were applied to bleach and degrade C.I. Reactive Green 8 and C.I. Reactive Red 45 organic dyes in water solutions. Two types of hybrid gas/liquid high voltage electrical discharge (corona) reactors, known as hybrid series and hybrid parallel were studied. The difference between these reactors relates to electrode configuration, which affects the amounts of ozone, hydrogen peroxide and hydroxyl radicals produced. Experiments were conducted using dye concentrations of 20 mgl(-1) and 75 mgl(-1), with and without NH4ZSM5 zeolite addition in order to determine possible effects of added solid particles to total process efficiency. The role of ozone in combination with zeolites was assessed through comparative direct ozonation experiments with ozone supplied by an ozone generator. UV/VIS spectrophotometric measurements and measurements of total organic carbon (TOC) were used for the determination of decolorization and mineralization rates.

Porous reactive wall for prevention of acid mine drainage: Results of a full-scale field demonstration

International Nuclear Information System (INIS)

Benner, S.G.; Blowes, D.W.; Ptacek, C.J.

1997-01-01

A porous reactive wall was installed in August, 1995, to treat mine drainage flowing within an aquifer at the Nickel Rim mine site, near Sudbury, Ontario. The reactive mixture was designed to maximize removal of metals and acid generating capacity from the groundwater by enhancing sulfate reduction and metal sulfide precipitation. The installed structure, composed of a mixed organic substrate, is 15 meters long, 3.6 meters deep and the flow path length (wall width) is 4 meters. Results of sampling nine months after installation, indicate that sulfate reduction and metal sulfide precipitation is occurring. Comparing the chemistry of water entering the wall to treated water exiting the wall nine months after installation: SO 4 concentrations decrease by >50% (from 2400-4800 mg/L to 60-3600 mg/L), Fe concentrations decrease by >95% (from 260-1300 mg/L to 1.0-40 mg/L), pH increased from 5.8 to 7.0 and alkalinity increased from 0-60 mg/L to 700-3200 mg/L as CaCO 3 . After passing through the reactive wall, the net acid generating potential of the aquifer water was converted from acid producing to acid consuming

Design of reactive power procurement in deregulated electricity market

African Journals Online (AJOL)

Reactive power management is different in the deregulated electricity market of various countries. In this paper, a novel reactive power procurement model is proposed, which ensure secure and reliable operation of deregulated electricity market. Various issues of reactive power management in the deregulated electricity ...

Memory reactivation improves visual perception.

Science.gov (United States)

Amar-Halpert, Rotem; Laor-Maayany, Rony; Nemni, Shlomi; Rosenblatt, Jonathan D; Censor, Nitzan

2017-10-01

Human perception thresholds can improve through learning. Here we report findings challenging the fundamental 'practice makes perfect' basis of procedural learning theory, showing that brief reactivations of encoded visual memories are sufficient to improve perceptual discrimination thresholds. Learning was comparable to standard practice-induced learning and was not due to short training per se, nor to an epiphenomenon of primed retrieval enhancement. The results demonstrate that basic perceptual functions can be substantially improved by memory reactivation, supporting a new account of perceptual learning dynamics.

Arsenite activates NFκB through induction of C-reactive protein

International Nuclear Information System (INIS)

Druwe, Ingrid L.; Sollome, James J.; Sanchez-Soria, Pablo; Hardwick, Rhiannon N.; Camenisch, Todd D.; Vaillancourt, Richard R.

2012-01-01

C-reactive protein (CRP) is an acute phase protein in humans. Elevated levels of CRP are produced in response to inflammatory cytokines and are associated with atherosclerosis, hypertension, cardiovascular disease and insulin resistance. Exposure to inorganic arsenic, a common environmental toxicant, also produces cardiovascular disorders, namely atherosclerosis and is associated with insulin-resistance. Inorganic arsenic has been shown to contribute to cardiac toxicities through production of reactive oxygen species (ROS) that result in the activation of NFκB. In this study we show that exposure of the hepatic cell line, HepG2, to environmentally relevant levels of arsenite (0.13 to 2 μM) results in elevated CRP expression and secretion. ROS analysis of the samples showed that a minimal amount of ROS are produced by HepG2 cells in response to these concentrations of arsenic. In addition, treatment of FvB mice with 100 ppb sodium arsenite in the drinking water for 6 months starting at weaning age resulted in dramatically higher levels of CRP in both the liver and inner medullary region of the kidney. Further, mouse Inner Medullary Collecting Duct cells (mIMCD-4), a mouse kidney cell line, were stimulated with 10 ng/ml CRP which resulted in activation of NFκB. Pretreatment with 10 nM Y27632, a known Rho-kinase inhibitor, prior to CRP exposure attenuated NFκB activation. These data suggest that arsenic causes the expression and secretion of CRP and that CRP activates NFκB through activation of the Rho-kinase pathway, thereby providing a novel pathway by which arsenic can contribute to metabolic syndrome and cardiovascular disease. -- Highlights: ► Exposure to arsenic can induce the expression and secretion of CRP. ► Mice treated with NaAsO 2 showed higher levels of CRP in both the liver and kidney. ► mIMCD-3 were stimulated with CRP which resulted in activation of NFκB. ► CRP activates NFκB through activation of the Rho-kinase pathway. ► Data provide

Arsenite activates NFκB through induction of C-reactive protein

Energy Technology Data Exchange (ETDEWEB)

Druwe, Ingrid L.; Sollome, James J.; Sanchez-Soria, Pablo; Hardwick, Rhiannon N.; Camenisch, Todd D.; Vaillancourt, Richard R., E-mail: vaillancourt@pharmacy.arizona.edu

2012-06-15

C-reactive protein (CRP) is an acute phase protein in humans. Elevated levels of CRP are produced in response to inflammatory cytokines and are associated with atherosclerosis, hypertension, cardiovascular disease and insulin resistance. Exposure to inorganic arsenic, a common environmental toxicant, also produces cardiovascular disorders, namely atherosclerosis and is associated with insulin-resistance. Inorganic arsenic has been shown to contribute to cardiac toxicities through production of reactive oxygen species (ROS) that result in the activation of NFκB. In this study we show that exposure of the hepatic cell line, HepG2, to environmentally relevant levels of arsenite (0.13 to 2 μM) results in elevated CRP expression and secretion. ROS analysis of the samples showed that a minimal amount of ROS are produced by HepG2 cells in response to these concentrations of arsenic. In addition, treatment of FvB mice with 100 ppb sodium arsenite in the drinking water for 6 months starting at weaning age resulted in dramatically higher levels of CRP in both the liver and inner medullary region of the kidney. Further, mouse Inner Medullary Collecting Duct cells (mIMCD-4), a mouse kidney cell line, were stimulated with 10 ng/ml CRP which resulted in activation of NFκB. Pretreatment with 10 nM Y27632, a known Rho-kinase inhibitor, prior to CRP exposure attenuated NFκB activation. These data suggest that arsenic causes the expression and secretion of CRP and that CRP activates NFκB through activation of the Rho-kinase pathway, thereby providing a novel pathway by which arsenic can contribute to metabolic syndrome and cardiovascular disease. -- Highlights: ► Exposure to arsenic can induce the expression and secretion of CRP. ► Mice treated with NaAsO{sub 2} showed higher levels of CRP in both the liver and kidney. ► mIMCD-3 were stimulated with CRP which resulted in activation of NFκB. ► CRP activates NFκB through activation of the Rho-kinase pathway. ► Data

Imidazolide monolayers for versatile reactive microcontact printing

NARCIS (Netherlands)

Hsu, S.H.; Reinhoudt, David; Huskens, Jurriaan; Velders, Aldrik

2008-01-01

Imidazolide monolayers prepared from the reaction of amino SAMs with N,N-carbonyldiimidazole (CDI) are used as a versatile platform for surface patterning with amino-, carboxyl- and alcohol-containing compounds through reactive microcontact printing (µCP). To demonstrate the surface reactivity of

Reactivity considerations for the on-line refuelling of a pebble bed modular reactor—Illustrating safety for the most reactive core fuel load

International Nuclear Information System (INIS)

Reitsma, Frederik

2012-01-01

In the multi-pass fuel management scheme employed for the pebble bed modular reactor the fuel pebbles are re-circulated until they reach the target burn-up. The rate at which fresh fuel is loaded and burned fuel is discharged is a result of the core neutronics cycle analysis but in practice (on the plant) this has to be controlled and managed by the fuel handling and storage system and use of the burnup measurement system. The excess reactivity is the additional reactivity available in the core during operating conditions that is the result of loading a fuel mixture in the core that is more reactive (less burned) than what is required to keep the reactor critical at full power operational conditions. The excess reactivity is balanced by the insertion of the control rods to keep the reactor critical. The excess reactivity allows flexibility in operations, for example to overcome the xenon build up when power is decreased as part of load follow. In order to limit reactivity excursions and to ensure safe shutdown the excess reactivity and thus the insertion depth of the control rods at normal operating conditions has to be managed. One way to do this is by operational procedures. The reactivity effect of long-term operation with the control rods inserted deeper than the design point is investigated and a control rod insertion limit is proposed that will not limit normal operations. The effects of other phenomena that can increase the power defect, such as higher-than-expected fuel temperatures, are also introduced. All of these cases are then evaluated by ensuring cold shutdown is still achievable and where appropriate by reactivity insertion accident analysis. These aspects are investigated on the PBMR 400 MW design.

Dengue serotype cross-reactive, anti-E protein antibodies confound specific immune memory for one year after infection

Directory of Open Access Journals (Sweden)

Ying Xiu eToh

2014-08-01

Full Text Available Dengue virus has four serotypes and is endemic globally in tropical countries. Neither a specific treatment nor an approved vaccine is available, and correlates of protection are not established. The standard neutralization assay cannot differentiate between serotype-specific and serotype cross-reactive antibodies in patients early after infection, leading to an overestimation of the long-term serotype-specific protection of an antibody response. It is known that the cross-reactive response in patients is temporary but few studies have assessed kinetics and potential changes in serum antibody specificity over time. To better define the specificity of polyclonal antibodies during disease and after recovery, longitudinal samples from patients with primary or secondary DENV-2 infection were collected over a period of one year. We found that serotype cross-reactive antibodies peaked three weeks after infection and subsided within one year. Since secondary patients rapidly produced antibodies specific for the virus envelope (E protein, an E-specific ELISA was superior compared to a virus particle-specific ELISA to identify patients with secondary infections. Dengue infection triggered a massive activation and mobilization of both naïve and memory B cells possibly from lymphoid organs into the blood, providing an explanation for the surge of circulating plasmablasts and the increase in cross-reactive E protein-specific antibodies.

Reactive ion etching of microphotonic structures

International Nuclear Information System (INIS)

Du, J.; Glasscock, J.; Vanajek, J.; Savvides, N.

2004-01-01

Full text: Fabrication of microphotonic structures such as planar waveguides and other periodic structures based on silicon technology has become increasingly important due to the potential for integration of planar optical devices. We have fabricated various periodic microstructures on silicon wafers using standard optical lithography and reactive ion etching (RIE). For optical applications the surface roughness and the sidewall angle or steepness of microstructures are the most critical factors. In particular, sidewall roughness of the etched waveguide core accounts for most of the optical propagation loss. We show that by varying the main RIE parameters such as gas pressure, RF power and CF 4 /Ar/O 2 gas composition it is possible to produce microstructures with near-vertical sidewalls and very smooth surfaces. In addition to plasma etching conditions, poor edge quality of the mask often causes sidewall roughness. We employed Ni/Cr metal masks in these experiments for deep etching, and used Ar + ion milling instead of wet chemical etching to open the mask. This improves the edge quality of the mask and ultimately results in smooth sidewalls

Portable digital reactivity meter for power reactors

Energy Technology Data Exchange (ETDEWEB)

Steffen, G [Nuklear-Ingenieur Service G.m.b.H., Hanau (Germany, F.R.)

1977-07-01

A digital reactivity meter has been developed, which can be used for all kinds of kinetic reactivity measurements in PWR's and BWR's. The input signals may be supplied by standard neutron detectors of the reactor. The hardware configuration consists of a minicomputer with ADC and DAC, a 'Silent' terminal and a high speed paper tape reader/punch. It is easily transportable. The reactivity meter solves the inverse kinetics equations for 6 delayed neutron groups, simultaneously for up to 8 logarithmic or linear neutron flux signals. It has been successfully tested at Biblis A PWR and the KRB BWR.

REACTIVITY OF BLOOD LYMPHOCYTES IN PULMONARY TUBERCULOSIS

Directory of Open Access Journals (Sweden)

R. R. Khasanova

2009-01-01

Full Text Available Evaluation of proliferative and IL-2-producing activity of peripheral blood lymphocytes wasperformed, using cultural methods, in patients with drug-sensitive and drug-resistant infiltrative pulmonary tuberculosis. The cell testing was performed at basal level and following in vitro stimulation with recombinant IL-2 and M. tuberculosis antigens. It was established that clinical course of infiltrative pulmonary tuberculosis, independently on drug sensitivity/resistance of the infectious pathogen, is accompanied by suppression of spontaneous lymphoproliferation. The levels of induced IL-2 production in drug-sensitive tuberculosis proved to be increased, whereas a reserve of IL-2-secreting reactivity of blood lymphocytes was lower than in drugresistant infection. Also, it was revealed that the level of lymphoproliferative response induced by IL-2, does not depend on clinical variant of tuberculosis, whereas stimulation of IL-2 production in blood lymphocytes is attained only in cases of drug-resistant tuberculosis variant.

Emotional reactivity and regulation in preschool-age children who stutter.

Science.gov (United States)

Ntourou, Katerina; Conture, Edward G; Walden, Tedra A

2013-09-01

This study experimentally investigated behavioral correlates of emotional reactivity and emotion regulation and their relation to speech (dis)fluency in preschool-age children who do (CWS) and do not (CWNS) stutter during emotion-eliciting conditions. Participants (18 CWS, 14 boys; 18 CWNS, 14 boys) completed two experimental tasks (1) a neutral ("apples and leaves in a transparent box," ALTB) and (2) a frustrating ("attractive toy in a transparent box," ATTB) task, both of which were followed by a narrative task. Dependent measures were emotional reactivity (positive affect, negative affect), emotion regulation (self-speech, distraction) exhibited during the ALTB and the ATTB tasks, percentage of stuttered disfluencies (SDs) and percentage of non-stuttered disfluencies (NSDs) produced during the narratives. Results indicated that preschool-age CWS exhibited significantly more negative emotion and more self-speech than preschool-age CWNS. For CWS only, emotion regulation behaviors (i.e., distraction, self-speech) during the experimental tasks were predictive of stuttered disfluencies during the subsequent narrative tasks. Furthermore, for CWS there was no relation between emotional processes and non-stuttered disfluencies, but CWNS's negative affect was significantly related to nonstuttered disfluencies. In general, present findings support the notion that emotional processes are associated with childhood stuttering. Specifically, findings are consistent with the notion that preschool-age CWS are more emotionally reactive than CWNS and that their self-speech regulatory attempts may be less than effective in modulating their emotions. The reader will be able to: (a) communicate the relevance of studying the role of emotion in developmental stuttering close to the onset of stuttering and (b) describe the main findings of the present study in relation to previous studies that have used different methodologies to investigate the role of emotion in developmental

A technique for computing bowing reactivity feedback in LMFBR's

International Nuclear Information System (INIS)

Finck, P.J.

1987-01-01

During normal or accidental transients occurring in a LMFBR core, the assemblies and their support structure are subjected to important thermal gradients which induce differential thermal expansions of the walls of the hexcans and differential displacement of the assembly support structure. These displacements, combined with the creep and swelling of structural materials, remain quite small, but the resulting reactivity changes constitute a significant component of the reactivity feedback coefficients used in safety analyses. It would be prohibitive to compute the reactivity changes due to all transients. Thus, the usual practice is to generate reactivity gradient tables. The purpose of the work presented here is twofold: develop and validate an efficient and accurate scheme for computing these reactivity tables; and to qualify this scheme

Autoantibodies in Senear-Usher Syndrome: Cross-Reactivity or Multiple Autoimmunity?

Directory of Open Access Journals (Sweden)

María Elena Pérez-Pérez

2012-01-01

Full Text Available Senear-Usher syndrome or pemphigus erythematosus is a pathology that overlaps clinically and serologically with pemphigus foliaceus and lupus erythematosus. Skin biopsies of patients with pemphigus erythematosus reveal acantholysis and deposits of immunoglobulins in desmosomes, and they are positive in the lupus band test. In the present paper, we determined whether the autoantibodies associated with pemphigus erythematosus targeted a single antigen or multiple antigens as a result of the stimulation of independent B cell clones. Our present paper demonstrates that patients with pemphigus erythematosus produce both antiepithelial antibodies specific for desmoglein 1 and 3 and antinuclear antibodies specific for Ro, La, Sm, and double-stranded DNA antigens. After eluting specific anti-epithelial or anti-nuclear antibodies, which were recovered and tested using double-fluorescence assays, a lack of cross-reactivity was demonstrated between desmosomes and nuclear and cytoplasmic lupus antigens. This result suggests that autoantibodies in pemphigus erythematosus are directed against different antigens and that these autoantibodies are produced by independent clones. Given these clinical and serological data, we suggest that pemphigus erythematosus behaves as a multiple autoimmune disease.

Estimation of quasi-critical reactivity

International Nuclear Information System (INIS)

Racz, A.

1992-02-01

The bank of Kalman filter method for reactivity and neutron density estimation originally suggested by D'Attellis and Cortina is critically overviewed. It is pointed out that the procedure cannot be applied reliably in such a form as the authors proposed, due to the filter divegence. An improved method, which is free from devergence problems are presented, as well. A new estimation technique is proposed and tested using computer simulation results. The procedure is applied for the estimation of small reactivity changes. (R.P.) 9 refs.; 2 figs.; 2 tabs

Reactive species in non-equilibrium atmospheric-pressure plasmas: Generation, transport, and biological effects

Energy Technology Data Exchange (ETDEWEB)

Lu, X., E-mail: luxinpei@hotmail.com [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan, Hubei 430074 (China); IFSA Collaborative Innovation Center, Shanghai Jiao Tong University, Shanghai 200240 (China); Naidis, G.V. [Joint Institute for High Temperatures, Russian Academy of Sciences, Moscow 125412 (Russian Federation); Laroussi, M. [Plasma Engineering & Medicine Institute, Old Dominion University, Norfolk, VA 23529 (United States); Reuter, S. [Leibniz Institute for Plasma Science and Technology, Felix-Hausdorff-Strasse 2, 17489 Greifswald (Germany); Graves, D.B. [Department of Chemical and Biomolecular Engineering, University of California, Berkeley, CA 94720 (United States); Ostrikov, K. [Institute for Future Environments, Queensland University of Technology, Brisbane, QLD 4000 (Australia); School of Physics, Chemistry, and Mechanical Engineering, Queensland University of Technology, Brisbane, QLD 4000 (Australia); Commonwealth Scientific and Industrial Research Organization, P.O.Box 218, Lindfield, NSW 2070 (Australia); School of Physics, The University of Sydney, Sydney, NSW 2006 (Australia)

2016-05-04

Non-equilibrium atmospheric-pressure plasmas have recently become a topical area of research owing to their diverse applications in health care and medicine, environmental remediation and pollution control, materials processing, electrochemistry, nanotechnology and other fields. This review focuses on the reactive electrons and ionic, atomic, molecular, and radical species that are produced in these plasmas and then transported from the point of generation to the point of interaction with the material, medium, living cells or tissues being processed. The most important mechanisms of generation and transport of the key species in the plasmas of atmospheric-pressure plasma jets and other non-equilibrium atmospheric-pressure plasmas are introduced and examined from the viewpoint of their applications in plasma hygiene and medicine and other relevant fields. Sophisticated high-precision, time-resolved plasma diagnostics approaches and techniques are presented and their applications to monitor the reactive species and plasma dynamics in the plasma jets and other discharges, both in the gas phase and during the plasma interaction with liquid media, are critically reviewed. The large amount of experimental data is supported by the theoretical models of reactive species generation and transport in the plasmas, surrounding gaseous environments, and plasma interaction with liquid media. These models are presented and their limitations are discussed. Special attention is paid to biological effects of the plasma-generated reactive oxygen and nitrogen (and some other) species in basic biological processes such as cell metabolism, proliferation, survival, etc. as well as plasma applications in bacterial inactivation, wound healing, cancer treatment and some others. Challenges and opportunities for theoretical and experimental research are discussed and the authors’ vision for the emerging convergence trends across several disciplines and application domains is presented to

Production of C-reactive protein by human lymphocytes

International Nuclear Information System (INIS)

Kuta, A.E.; Baum, L.L.

1986-01-01

C-reactive protein (CRP) is a major acute phase serum protein in humans; it is detectable at very high concentrations during infection and tissue trauma. This protein is a pentame composed of five identical, 21,500 MW subunits. CRP is detectable on the surface of approximately 4% of normal peripheral blood lymphocytes (PBL). CRP binds its physiological ligands in a Ca ++ dependent manner; removal of Ca ++ does not alter the expression of CRP on the lymphocyte surface. Recently, investigators in this laboratory reported substantial inhibition of natural killer cell (NK) activity with anti-CRP antibodies. The following studies were undertaken to determine the origin of surface-CRP (S-CRP) found on normal PBL. Cells were incubated in methionine-free DMEM supplemented with 35 S-methionine. Cells were lysed and subjected to immunoprecipitation with anti-CRP and Staphylococcus aureus; immunoprecipitates were analyzed by SDS-PAGE and autoradiography. Data presented here suggested that lymphocytes, in particular, LGL produce small amounts of CRP and express it on their surface. Lymphocytes do not appear to secrete CRP since no CRP could be detected in culture supernatants. In addition, preliminary evidence indicates that peripheral blood monocytes produce no detectable CRP. Present studies utilizing Northern blot analysis are underway in order to detect CRP-mRNA

Measurements of total OH reactivity during PROPHET-AMOS 2016

Science.gov (United States)

Rickly, P.; Sakowski, J.; Bottorff, B.; Lew, M.; Stevens, P. S.; Sklaveniti, S.; Locoge, N.; Dusanter, S.

2017-12-01

As one of the main oxidant in the atmosphere, the hydroxyl radical (OH) initiates the oxidation of volatile organic compounds that can lead to the formation of ozone and secondary organic aerosols. Understanding both the sources and sinks of OH is therefore important to address issues related to air quality and climate change. Measurements of total OH reactivity can provide an important test of our understanding of the OH radical budget. Recent measurements of total reactivity in many environments have been greater than calculated based on the measured concentration of VOCs, suggesting that important OH sinks in these environments are not well characterized. Measurements of total OH reactivity were performed in a forested environment during the PROPHET - AMOS field campaign (Program for Research on Oxidants: PHotochemisty, Emissions, and Transport - Atmospheric Measurements of Oxidants in Summer) using the Comparative Reactivity Method (CRM) and the Total OH Loss Rate Method (TOHLM). The site is characterized by large emissions of isoprene and monoterpenes and low anthropogenic influence. Measurements of total OH reactivity using these two techniques agree to within their respective uncertainties, giving confidence in the measured OH reactivity. In addition, measurements of trace gases (VOCs, NOx, O3) were used to perform a comprehensive apportionment of OH sinks. These measurements are used in a chemical model using the Master Chemical Mechanism to calculate the expected OH reactivity. The results will be compared to previous measurements of total OH reactivity at this site.

Second Reactivation of Neurocysticercosis: A Case Report

Energy Technology Data Exchange (ETDEWEB)

Shim, Young Sup; Hwang, Hee Young; Choi, Hye Young; Kim, Jee Eun; Kim, Hyung Sik [Gil Hospital, Incheon (Korea, Republic of)

2010-02-15

This report describes the first case involving a second reactivation of neurocysticercosis. There was peripheral enhancement and surrounding edema at multiple calcified lesions in both cerebral hemispheres on the brain MRI. One must be aware of the possibility of reactivation of neurocysticercosis to make the correct diagnosis

Purification and properties of extracellular polysaccharide (EPS) antigens produced by different mould species.

Science.gov (United States)

Notermans, S; Wieten, G; Engel, H W; Rombouts, F M; Hoogerhout, P; van Boom, J H

1987-02-01

Extracellular polysaccharide (EPS) antigens produced by different mould species were purified and partially characterized. Purification included (NH4)2SO4 treatment, Sepharose CL-4B column chromatography and Con A-sepharose chromatography. The EPS of Penicillium digitatum, Mucor racemosus and Cladosporium cladosporioides showed high antigenic capacities. Immunologically the EPS were partially genus-specific, but cross-reactivity was observed. The EPS antigens produced by species of Penicillium, Aspergillus repens and Geotrichum candidum lost their immunological activity upon heating (100 degrees C) at pH 1.8, while the EPS antigen of M. racemosus, Rhizopus oligosporus and C. cladosporioides were stable under the same conditions. The dominant monosaccharides present in the EPS antigen were mannose, galactose and glucose. The EPS obtained from cultures of M. racemosus and R. oligosporus also contained rhamnose. In the EPS produced by Penicillium spp. and A. repens the galactose residues were determined to be immunodominant.

IL-22 is mainly produced by IFNγ-secreting cells but is dispensable for host protection against Mycobacterium tuberculosis infection.

Directory of Open Access Journals (Sweden)

Jochen Behrends

Full Text Available Anti-inflammatory treatment of autoimmune diseases is associated with an increased risk of reactivation tuberculosis (TB. Besides interleukin (IL-17A, IL-22 represents a classical T helper (TH17 cytokine and shares similar pathological effects in inflammatory diseases such as psoriasis or arthritis. Whereas IL-17A supports protective immune responses during mycobacterial infections, the role of IL-22 after infection with Mycobacterium tuberculosis (Mtb is yet poorly characterized. Therefore, we here characterize the cell types producing IL-22 and the protective function of this cytokine during experimental TB in mice. Like IL-17A, IL-22 is expressed early after infection with Mtb in an IL-23-dependent manner. Surprisingly, the majority of IL-22-producing cells are not positive for IL-17A but have rather functional characteristics of interferon-gamma-producing TH1 cells. Although we found minor differences in the number of naive and central memory T cells as well as in the frequency of TH1 and polyfunctional T cells in mice deficient for IL-22, the absence of IL-22 does not affect the outcome of Mtb infection. Our study revealed that although produced by TH1 cells, IL-22 is dispensable for protective immune responses during TB. Therefore, targeting of IL-22 in inflammatory disease may represent a therapeutic approach that does not incur the danger of reactivation TB.

Cue-reactivity in behavioral addictions: A meta-analysis and methodological considerations.

Science.gov (United States)

Starcke, Katrin; Antons, Stephanie; Trotzke, Patrick; Brand, Matthias

2018-05-23

Background and aims Recent research has applied cue-reactivity paradigms to behavioral addictions. The aim of the current meta-analysis is to systematically analyze the effects of learning-based cue-reactivity in behavioral addictions. Methods The current meta-analysis includes 18 studies (29 data sets, 510 participants) that have used a cue-reactivity paradigm in persons with gambling (eight studies), gaming (nine studies), or buying (one study) disorders. We compared subjective, peripheral physiological, electroencephal, and neural responses toward addiction-relevant cues in patients versus control participants and toward addiction-relevant cues versus control cues in patients. Results Persons with behavioral addictions showed higher cue-reactivity toward addiction-relevant cues compared with control participants: subjective cue-reactivity (d = 0.84, p = .01) and peripheral physiological and electroencephal measures of cue-reactivity (d = 0.61, p buying disorders also showed higher cue-reactivity toward addiction-relevant cues compared with control cues: subjective cue-reactivity (d = 0.39, p = .11) and peripheral physiological and electroencephal measures of cue-reactivity (d = 0.47, p = .05). Increased neural activation was found in the caudate nucleus, inferior frontal gyrus, angular gyrus, inferior network, and precuneus. Discussion and conclusions Cue-reactivity not only exists in substance-use disorders but also in gambling, gaming, and buying disorders. Future research should differentiate between cue-reactivity in addictive behaviors and cue-reactivity in functional excessive behaviors such as passions, hobbies, or professions.

Sugarcane bagasse powder as biosorbent for reactive red 120 removals from aqueous solution

Science.gov (United States)

Ahmad, S.; Wong, Y. C.; Veloo, K. V.

2018-04-01

Reactive red 120 is used as a textile dye for fabric coloring. The dye waste is produced during textile finishing process subsequently released directly to water bodies which giving harmful effects to the environment due to the carcinogenic characteristic. Adsorption process becomes an effective treatment to treat textile dye. This research emphasizes the treatment of textile dye namely reactive red 120 (RR120) by using sugarcane bagasse powder. The batch study was carried out under varying parameters such as 60 minutes contact time, pH (1-8), dye concentration (5-25 mg/L), particle size (125-500 μm) and biosorbent dosage (0.01-0.2 g/L). The maximum adsorption percentage of RR120 was 94.62%. The adsorption of dye was increased with the decreasing of pH, initial dye concentration and particle size. Sugarcane bagasse powder as low-cost biosorbent was established using Fourier Transform Infrared (FTIR) and scanning electron microscopy (SEM). This locally agricultural waste could be upgraded into useful material which is biosorbent that promising for decolorization of colored textile wastewater.

Innovative reactive distillation process for the production of the MTBE substitute isooctane from isobutene

Energy Technology Data Exchange (ETDEWEB)

Chalakova, M. [Magdeburg Univ. (Germany). Process Systems Engineering; Kaur, R.; Mahajani, S. [Indian Inst. of Technology, Mumbai (India); Freund, H. [Max-Planck-Institute for Dynamics of Complex Technical Systems, Magdeburg (Germany); Sundmacher, K. [Magdeburg Univ. (Germany). Process Systems Engineering]|[Max-Planck-Institute for Dynamics of Complex Technical Systems, Magdeburg (Germany)

2007-07-01

Isooctane is a promising candidate to replace MTBE as gasoline additive if it can be produced in economically and environmentally efficient processes. A promising reaction way at mild conditions is the so called indirect alkylation of isobutene (IB). In the present work two innovative reactive distillation (RD) concepts where the reactions are carried out either simultaneously (fully integrated) or sequentially (partially integrated) are designed. Suitable operation conditions are identified and a comparison with the conventional process scheme under performance and economic aspects is carried out. (orig.)

Isothermal temperature reactivity coefficient measurement in TRIGA reactor

International Nuclear Information System (INIS)

Zagar, T.; Ravnik, M.; Trkov, A.

2002-01-01

Direct measurement of an isothermal temperature reactivity coefficient at room temperatures in TRIGA Mark II research reactor at Jozef Stefan Institute in Ljubljana is presented. Temperature reactivity coefficient was measured in the temperature range between 15 o C and 25 o C. All reactivity measurements were performed at almost zero reactor power to reduce or completely eliminate nuclear heating. Slow and steady temperature decrease was controlled using the reactor tank cooling system. In this way the temperatures of fuel, of moderator and of coolant were kept in equilibrium throughout the measurements. It was found out that TRIGA reactor core loaded with standard fuel elements with stainless steel cladding has small positive isothermal temperature reactivity coefficient in this temperature range.(author)

Production and characterization of thermoplastic cassava starch, functionalized poly(lactic acid), and their reactive compatibilized blends

Science.gov (United States)

Detyothin, Sukeewan

Cassava starch was blended with glycerol using a co-rotating twin-screw extruder (TSE). Thermoplastic cassava starch (TPCS) at a ratio of 70/30 by weight of cassava/glycerol was selected and further blended with other polymers. TPCS sheets made from compression molding had low tensile strength (0.45 +/- 0.05 MPa) and Young's modulus (1.24 +/- 0.58 MPa), but moderate elongation at break (83.0 +/- 0.18.6%), medium level of oxygen permeability, and high water vapor permeability with a very high rate of water absorption. TPCS was blended with poly(lactic acid) (PLA) at various ratios by using a TSE. The blend resins exhibited good properties such as increased thermal stability (Tmax) and crystallinity of PLA, and improved water sensitivity and processability of TPCS. PLA and TPCS exhibited a high interfacial tension between the two phases of 7.9 mJ·m -2, indicating the formation of an incompatible, immiscible blend. SEM micrographs showed a non-homogeneous distribution of TPCS droplets in the PLA continuous phase. TEM micrographs of the blend films made by cast-film extrusion showed coalescence of the TPCS droplets in the PLA continuous phase of the blend, indicating that the compatibility between the polymer pair needs to be improved. A response surface methodology (RSM) design was used to analyze the effects of maleic anhydride (MA) and 2,5-bis(tert-butylperoxy)-2,5-dimethylhexane (Luperox or L101) contents, and TSE screw speed on the degree of grafted MA and number average molecular weight (Mn) of functionalized PLA (PLA-g-MA), a reactive compatibilizer. PLA-g- MA made by reactive extrusion had an array of colors depending on the content of L101 and MA used. New FTIR peaks suggested that MA was grafted onto the PLA backbone and oligomeric MA may occur. Increasing L101 increased the degree of grafting and decreased Mn, but the Mn of the PLA-g-MA's produced with a high amount of L101 was stable during storage. MA exhibited an optimum concentration for maximizing the

REACTIVE POWER DEVICES IN SYSTEMS OF ELECTRIC TRACTION

Directory of Open Access Journals (Sweden)

M. O. Kostin

2010-04-01

Full Text Available A comparative characteristic of different concepts and expressions for determination of reactive power in the circuits with non-sinusoidal electric values has been given. For the first Ukrainian electric locomotives of DE1 type with the system of DC electric traction, the values of reactive power after Budeany, Fryze, and also the differential, integral and generalized reactive powers have been determined. Some measures on reducing its consumption by the DC electric rolling stock have been suggested.

Application of CYP102A1M11H as a tool for the generation of protein adducts of reactive drug metabolites

NARCIS (Netherlands)

Boerma, J.S.; Vermeulen, N.P.E.; Commandeur, J.N.M.

2011-01-01

Covalent binding of reactive metabolites (RMs) to proteins is considered to be one of the important mechanisms by which drugs can cause tissue damage. To facilitate the study of drug-protein adducts, we developed a potentially generic method for producing high levels of covalently modified proteins.

Advancing Reactive Tracer Methods for Measurement of Thermal Evolution in Geothermal Reservoirs: Final Report

Energy Technology Data Exchange (ETDEWEB)

Mitchell A. Plummer; Carl D. Palmer; Earl D. Mattson; Laurence C. Hull; George D. Redden

2011-07-01

The injection of cold fluids into engineered geothermal system (EGS) and conventional geothermal reservoirs may be done to help extract heat from the subsurface or to maintain pressures within the reservoir (e.g., Rose et al., 2001). As these injected fluids move along fractures, they acquire heat from the rock matrix and remove it from the reservoir as they are extracted to the surface. A consequence of such injection is the migration of a cold-fluid front through the reservoir (Figure 1) that could eventually reach the production well and result in the lowering of the temperature of the produced fluids (thermal breakthrough). Efficient operation of an EGS as well as conventional geothermal systems involving cold-fluid injection requires accurate and timely information about thermal depletion of the reservoir in response to operation. In particular, accurate predictions of the time to thermal breakthrough and subsequent rate of thermal drawdown are necessary for reservoir management, design of fracture stimulation and well drilling programs, and forecasting of economic return. A potential method for estimating migration of a cold front between an injection well and a production well is through application of reactive tracer tests, using chemical whose rate of degradation is dependent on the reservoir temperature between the two wells (e.g., Robinson 1985). With repeated tests, the rate of migration of the thermal front can be determined, and the time to thermal breakthrough calculated. While the basic theory behind the concept of thermal tracers has been understood for some time, effective application of the method has yet to be demonstrated. This report describes results of a study that used several methods to investigate application of reactive tracers to monitoring the thermal evolution of a geothermal reservoir. These methods included (1) mathematical investigation of the sensitivity of known and hypothetical reactive tracers, (2) laboratory testing of novel

Process intensification for biodiesel production from Jatropha curcas L. seeds: Supercritical reactive extraction process parameters study

International Nuclear Information System (INIS)

Lim, Steven; Lee, Keat Teong

2013-01-01

Highlights: ► Investigation of supercritical reactive extraction process for biodiesel production. ► Focus is given on optimizing methyl esters yield for Jatropha curcas L. seeds. ► Influence of process parameters to the reaction are discussed thoroughly. ► Comparison between the novel reaction with conventional process are studied. ► High methyl esters yield can be obtained without pre-extraction and catalyst. -- Abstract: In a bid to increase the cost competitiveness of biodiesel production against mineral diesel, process intensification has been studied for numerous biodiesel processing technologies. Subsequently, reactive extraction or in situ transesterification is actively being explored in which the solid oil-bearing seeds are used as the reactant directly with short-chain alcohol. This eliminates separate oil extraction process and combines both extraction and transesterification in a single unit. Supercritical reactive extraction takes one step further by substituting the role of catalyst with supercritical conditions to achieve higher yield and shorter processing time. In this work, supercritical reactive extraction with methanol was carried out in a high-pressure batch reactor to produce fatty acid methyl esters (FAMEs) from Jatropha curcas L. seeds. Material and process parameters including space loading, solvent to seed ratio, co-solvent (n-hexane) to seed ratio, reaction temperature, reaction time and mixing intensity were varied one at a time and optimized based on two responses i.e. extraction efficiency, M extract and FAME yield, F y . The optimum responses for supercritical reactive extraction obtained were 104.17% w/w and 99.67% w/w (relative to 100% lipid extraction with n-hexane) for M extract and F y respectively under the following conditions: 54.0 ml/g space loading, 5.0 ml/g methanol to seeds ratio, 300 °C, 9.5 MPa (Mega Pascal), 30 min reaction time and without n-hexane as co-solvent or any agitation source. This proved that

Reactive Transport Modeling of Microbe-mediated Fe (II) Oxidation for Enhanced Oil Recovery

Science.gov (United States)

Surasani, V.; Li, L.

2011-12-01

Microbially Enhanced Oil Recovery (MEOR) aims to improve the recovery of entrapped heavy oil in depleted reservoirs using microbe-based technology. Reservoir ecosystems often contain diverse microbial communities those can interact with subsurface fluids and minerals through a network of nutrients and energy fluxes. Microbe-mediated reactions products include gases, biosurfactants, biopolymers those can alter the properties of oil and interfacial interactions between oil, brine, and rocks. In addition, the produced biomass and mineral precipitates can change the reservoir permeability profile and increase sweeping efficiency. Under subsurface conditions, the injection of nitrate and Fe (II) as the electron acceptor and donor allows bacteria to grow. The reaction products include minerals such as Fe(OH)3 and nitrogen containing gases. These reaction products can have large impact on oil and reservoir properties and can enhance the recovery of trapped oil. This work aims to understand the Fe(II) oxidation by nitrate under conditions relevant to MEOR. Reactive transport modeling is used to simulate the fluid flow, transport, and reactions involved in this process. Here we developed a complex reactive network for microbial mediated nitrate-dependent Fe (II) oxidation that involves both thermodynamic controlled aqueous reactions and kinetic controlled Fe (II) mineral reaction. Reactive transport modeling is used to understand and quantify the coupling between flow, transport, and reaction processes. Our results identify key parameter controls those are important for the alteration of permeability profile under field conditions.

Clojure reactive programming

CERN Document Server

Borges, Leonardo

2015-01-01

If you are a Clojure developer who is interested in using Reactive Programming to build asynchronous and concurrent applications, this book is for you. Knowledge of Clojure and Leiningen is required. Basic understanding of ClojureScript will be helpful for the web chapters, although it is not strictly necessary.

Structure, Reactivity and Dynamics

Indian Academy of Sciences (India)

Understanding structure, reactivity and dynamics is the core issue in chemical ... functional theory (DFT) calculations, molecular dynamics (MD) simulations, light- ... between water and protein oxygen atoms, the superionic conductors which ...

Effects of several types of biomass fuels on the yield, nanostructure and reactivity of soot from fast pyrolysis at high temperatures

DEFF Research Database (Denmark)

Trubetskaya, Anna; Jensen, Peter Arendt; Jensen, Anker Degn

2016-01-01

This study presents the effect of biomass origin on the yield, nanostructure and reactivity of soot. Soot was produced from wood and herbaceous biomass pyrolysis at high heating rates and at temperatures of 1250 and 1400 °C in a drop tube furnace. The structure of solid residues was characterized...

Microstructure and wear resistance of Al2O3-M7C3/Fe composite coatings produced by laser controlled reactive synthesis

Science.gov (United States)

Tan, Hui; Luo, Zhen; Li, Yang; Yan, Fuyu; Duan, Rui

2015-05-01

Based on the principle of thermite reaction of Al and Fe2O3 powders, the Al2O3 ceramic reinforced Fe-based composite coatings were fabricated on a steel substrate by laser controlled reactive synthesis and cladding. The effects of different additions of thermite reactants on the phase transition, microstructure evolution, microhardness and wear resistance of the composite coatings were investigated by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Vickers microhardness and block-on-ring wear test, respectively. The results show that Al2O3 ceramic and M7C3 carbide are in situ synthesized via the laser controlled reactive synthesis. The Al2O3 ceramic and M7C3 carbides prefer to distribute along the γ-Fe phase boundary continuously, which separates the γ-Fe matrix and is beneficial to the grain refinement. With the increase of thermite reactants, the amount of Al2O3 ceramic and M7C3 carbide in the composite coatings increases gradually. Moreover the cladding layer changes from dendritic structure to columnar structure and martensite structure in the heat affected zone becomes coarse. The increased thermite reactants improve the microhardness and wear resistance of the in situ composite coatings obviously and enhance the hardness of the heat affected zone, which should be ascribed to the grain refinement, ceramic and carbide precipitation and solid solution strengthening.

Sexual orientation modulates endocrine stress reactivity.

Science.gov (United States)

Juster, Robert-Paul; Hatzenbuehler, Mark L; Mendrek, Adrianna; Pfaus, James G; Smith, Nathan Grant; Johnson, Philip Jai; Lefebvre-Louis, Jean-Philippe; Raymond, Catherine; Marin, Marie-France; Sindi, Shireen; Lupien, Sonia J; Pruessner, Jens C

2015-04-01

Biological sex differences and sociocultural gender diversity influence endocrine stress reactivity. Although numerous studies have shown that men typically activate stronger stress responses than women when exposed to laboratory-based psychosocial stressors, it is unclear whether sexual orientation further modulates stress reactivity. Given that lesbian, gay, and bisexual (LGB) individuals frequently report heightened distress secondary to stigma-related stressors, we investigated whether cortisol stress reactivity differs between LGB individuals and heterosexual individuals in response to a well-validated psychosocial stressor. The study population comprised 87 healthy adults (mean age, 25 years) who were grouped according to their biological sex and their gendered sexual orientation: lesbian/bisexual women (n = 20), heterosexual women (n = 21), gay/bisexual men (n = 26), and heterosexual men (n = 20). Investigators collected 10 salivary cortisol samples throughout a 2-hour afternoon visit involving exposure to the Trier Social Stress Test modified to maximize between-sex differences. Relative to heterosexual women, lesbian/bisexual women showed higher cortisol stress reactivity 40 min after exposure to the stressor. In contrast, gay/bisexual men displayed lower overall cortisol concentrations throughout testing compared with heterosexual men. Main findings were significant while adjusting for sex hormones (estradiol-to-progesterone ratio in women and testosterone in men), age, self-esteem, and disclosure status (whether LGB participants had completed their "coming out"). Our results provide novel evidence for gender-based modulation of cortisol stress reactivity based on sexual orientation that goes beyond well-established between-sex differences. This study raises several important avenues for future research related to the physiologic functioning of LGB populations and gender diversity more broadly. Copyright © 2015 Society of Biological Psychiatry. Published

Sexual Orientation Modulates Endocrine Stress Reactivity

Science.gov (United States)

Juster, Robert-Paul; Hatzenbuehler, Mark L.; Mendrek, Adrianna; Pfaus, James G.; Smith, Nathan Grant; Johnson, Philip Jai; Lefebvre-Louis, Jean-Philippe; Raymond, Catherine; Marin, Marie-France; Sindi, Shireen; Lupien, Sonia J.; Pruessner, Jens C.

2015-01-01

BACKGROUND Biological sex differences and sociocultural gender diversity influence endocrine stress reactivity. Although numerous studies have shown that men typically activate stronger stress responses than women when exposed to laboratory-based psychosocial stressors, it is unclear whether sexual orientation further modulates stress reactivity. Given that lesbian, gay, and bisexual (LGB) individuals frequently report heightened distress secondary to stigma-related stressors, we investigated whether cortisol stress reactivity differs between LGB individuals and heterosexual individuals in response to a well-validated psychosocial stressor. METHODS The study population comprised 87 healthy adults (mean age, 25 years) who were grouped according to their biological sex and their gendered sexual orientation: lesbian/bisexual women (n = 20), heterosexual women (n = 21), gay/bisexual men (n = 26), and heterosexual men (n = 20). Investigators collected 10 salivary cortisol samples throughout a 2-hour afternoon visit involving exposure to the Trier Social Stress Test modified to maximize between-sex differences. RESULTS Relative to heterosexual women, lesbian/bisexual women showed higher cortisol stress reactivity 40 min after exposure to the stressor. In contrast, gay/bisexual men displayed lower overall cortisol concentrations throughout testing compared with heterosexual men. Main findings were significant while adjusting for sex hormones (estradiol-to-progesterone ratio in women and testosterone in men), age, self-esteem, and disclosure status (whether LGB participants had completed their “coming out”). CONCLUSIONS Our results provide novel evidence for gender-based modulation of cortisol stress reactivity based on sexual orientation that goes beyond well-established between-sex differences. This study raises several important avenues for future research related to the physiologic functioning of LGB populations and gender diversity more broadly. PMID:25444167

Novel understanding of self-reactive T cells

DEFF Research Database (Denmark)

Andersen, Mads Hald

2016-01-01

In a recent issue of Immunity, Mark Davis and colleagues describe that thymic selection does not eliminate but prunes self-reactive T cell clones. Self-reactive T cells are a natural part of the T-cell repertoire and may be important in the fight against pathogens in addition to being important...

Measurements of low reactivities using a reactor oscillator

International Nuclear Information System (INIS)

Obradovic, D.; Petrovic, M.

1965-12-01

Most of the methods of measuring reactivity are limited to the region from several hundreds to several thousands of pcm. The present work develops a method of measuring low reactivities from several pcm to about 600 pcm using the ROB-1 reactor oscillator on the RB reactor of the Boris Kidric Institute of Nuclear Sciences at Vinca. The accuracy of measurement is better than 1%. Several methods are used to measure low reactivities. The most often used is the method based on measuring the stable reactor period. The bottom limit of this method is about 30 porn /1,2/. For control rod calibration the method of rod oscillation is used /3,4/. This method is confronted with considerable influence of space effects /5/. Reference /6/ reports on a method for measuring the reactivity coefficient at a critical level in liquid-moderated reactors. The method is based on measuring reactor response to the oscillation of the moderator about the critical level. The present work reports on a method of determining the reactivity by measuring the phase shift between the perturbation of the effective multiplication factor and reactor response. With the use of the ROB-1 reactor oscillator, the method allows measurement of the reactivity from several pcm to about 600 pcm with an accuracy of 1% (author)

Measurements of low reactivities using a reactor oscillator

Energy Technology Data Exchange (ETDEWEB)

Obradovic, D; Petrovic, M [Institute of nuclear sciences Boris Kidric, Vinca, Beograd (Yugoslavia)

1965-12-15

Most of the methods of measuring reactivity are limited to the region from several hundreds to several thousands of pcm. The present work develops a method of measuring low reactivities from several pcm to about 600 pcm using the ROB-1 reactor oscillator on the RB reactor of the Boris Kidric Institute of Nuclear Sciences at Vinca. The accuracy of measurement is better than 1%. Several methods are used to measure low reactivities. The most often used is the method based on measuring the stable reactor period. The bottom limit of this method is about 30 porn /1,2/. For control rod calibration the method of rod oscillation is used /3,4/. This method is confronted with considerable influence of space effects /5/. Reference /6/ reports on a method for measuring the reactivity coefficient at a critical level in liquid-moderated reactors. The method is based on measuring reactor response to the oscillation of the moderator about the critical level. The present work reports on a method of determining the reactivity by measuring the phase shift between the perturbation of the effective multiplication factor and reactor response. With the use of the ROB-1 reactor oscillator, the method allows measurement of the reactivity from several pcm to about 600 pcm with an accuracy of 1% (author)

Rheology at the Interface and the Role of the Interphase in Reactive Functionalized Multilayer Polymers in Coextrusion Process

Science.gov (United States)

Lamnawar, Khalid; Maazouz, Abderrahim

2008-07-01

Coextrusion technologies are commonly used to produce multilayered composite sheets or films for a large range of applications from food packaging to optics. The contrast of rheological properties between layers can lead to interfacial instabilities during flow. Important theoretical and experimental advances regarding the stability of compatible and incompatible polymers have, during the last decades, been made using a mechanical approach. However, few research efforts have been dedicated to the physicochemical affinity between the neighboring layers. The present study deals with the influence of this affinity on interfacial instabilities for functionalized incompatible polymers. Polyamide (PA6)/polyethylene grafted with glycidyl methacrylate (PE-GMA) was used as a reactive system and PE/PA6 as a non reactive one. Two grades of polyamide (PA6) were used in order to change the viscosity and elasticity ratios between PE (or PE-GMA) and PA6. It was experimentally confirmed, in this case, that weak disturbance can be predicted by considering an interphase of non-zero thickness (corresponding to an interdiffusion/reaction zone) instead of a purely geometrical interface between the two reactive layers. According to the rheological investigations from previous work which the interphase effect can be probed, an experimental strategy was here formulated to optimize the process by listing the parameters that controlled the stability of the reactive multilayer flows. Hence, based on this analysis, guidelines for a stable coextrusion of reactive functionalized polymers can be provided coupling the classical parameters (viscosity, elasticity and layer ratios) and the physicochemical affinity at the polymer/polymer interface.

Cardiovascular Reactivity, Stress, and Physical Activity

Directory of Open Access Journals (Sweden)

Chun-Jung eHuang

2013-11-01

Full Text Available Psychological stress has been proposed as a major contributor to the progression of cardiovascular disease (CVD. Acute mental stress can activate the sympathetic-adrenal-medullary (SAM axis, eliciting the release of catecholamines (NE and EPI resulting in the elevation of heart rate (HR and blood pressure (BP. Combined stress (psychological and physical can exacerbate these cardiovascular responses, which may partially contribute to the elevated risk of CVD and increased proportionate mortality risks experienced by some occupations (e.g., firefighting and law enforcement. Studies have supported the benefits of physical activity on physiological and psychological health, including the cardiovascular response to acute stress. Aerobically trained individuals exhibit lower sympathetic nervous system (e.g., HR reactivity and enhanced cardiovascular efficiency (e.g., lower vascular reactivity and decreased recovery time in response to physical and/or psychological stress. In addition, resistance training has been demonstrated to attenuate cardiovascular responses and improve mental health. This review will examine stress-induced cardiovascular reactivity and plausible explanations for how exercise training and physical fitness (aerobic and resistance exercise can attenuate cardiovascular responses to stress. This enhanced functionality may facilitate a reduction in the incidence of stroke and myocardial infarction. Finally, this review will also address the interaction of obesity and physical activity on cardiovascular reactivity and CVD.

A range of newly developed mobile generators to dynamically produce SI-traceable reference gas mixtures for reactive compounds at atmospheric concentrations

Science.gov (United States)

Leuenberger, Daiana; Pascale, Céline; Guillevic, Myriam; Ackermann, Andreas; Niederhauser, Bernhard

2017-04-01

Three new mobile facilities have been developed at METAS to dynamically generate SI-traceable reference gas mixtures for a variety of reactive compounds at atmospheric amount of substance fractions and at very low levels of uncertainty (Ux balance. The carrier gas is previously purified from the compounds of interest using commercially available purification cartridges. The permeation chambers of ReGaS2 and ReGaS3 have multiple individual cells allowing for the generation of mixtures containing up to 5 different components if required. ReGaS1 allows for the generation of one-component mixtures only. These primary mixtures are then diluted to the required amount of substance fractions using thermal mass flow controllers for full flexibility and adaptability of the generation process over the entire range of possible concentrations. In order to considerably reduce adsorption/desorption processes and thus stabilisation time, all electro-polished stainless steel parts of ReGaS1 and ReGaS2 in contact with the reference gas mixtures are passivated with SilcoNert2000® surface coating. These three state-of-the-art mobile reference gas generators are applicable under both, laboratory and field conditions. Moreover the dynamic generation method can be adapted and applied to a large variety of molecules (e.g. BTEX, CFCs, HCFCs, HFCs and other refrigerants) and is particularly suitable for reactive gas species and/or at concentration ranges which are unstable when stored in pressurised cylinders. Acknowledgement: This work was supported by the European Metrology Research Programme (EMRP). The EMRP is jointly funded by the EMRP participating countries within EURAMET and the European Union

Enhancing Reactivity in Structural Energetic Materials

Science.gov (United States)

Glumac, Nick

2017-06-01

In many structural energetic materials, only a small fraction of the metal oxidizes, and yet this provides a significant boost in the overall energy release of the system. Different methodologies to enhance this reactivity include alloying and geometric modifications of microstructure of the reactive material (RM). In this presentation, we present the results of several years of systematic study of both chemical (alloy) and mechanical (geometry) effects on reactivity for systems with typical charge to case mass ratios. Alloys of aluminum with magnesium and lithium are considered, as these are common alloys in aerospace applications. In terms of geometric modifications, we consider surface texturing, inclusion of dense additives, and inclusion of voids. In all modifications, a measurable influence on output is observed, and this influence is related to the fragment size distribution measured from the observed residue. Support from DTRA is gratefully acknowledged.

Taskable Reactive Agent Communities

National Research Council Canada - National Science Library

Myers, Karen

2002-01-01

The focus of Taskable Reactive Agent Communities (TRAC) project was to develop mixed-initiative technology to enable humans to supervise and manage teams of agents as they perform tasks in dynamic environments...

Development of an alternative reactivity meter for nuclear reactor control

International Nuclear Information System (INIS)

Ferreira, P.S.B.

1991-01-01

This work describes an alternative version of the IPEN-CNEN/SP reactivity-meter. This new version utilizes a programmable electrometer (to realize the data acquisition) and a IBM-PC microcomputer to process the reactivity calculation. The aim of development of this alternative reactivity-meter is to have available a equipment of measurements of reactivity in the case of the later version show any problem during an experiment. (author)

Management of hepatitis B reactivation in patients receiving cancer chemotherapy

OpenAIRE

Huang, Yi-Wen; Chung, Raymond T.

2012-01-01

Hepatitis B virus (HBV) reactivation is well documented in previously resolved or inactive HBV carriers who receive cancer chemotherapy. The consequences of HBV reactivation range from self-limited conditions to fulminant hepatic failure and death. HBV reactivation also leads to premature termination of chemotherapy or delay in treatment schedules. This review summarizes current knowledge of management of HBV reactivation in patients receiving cancer chemotherapy. HBV surface antigen (HBsAg) ...

The impact of carbon dioxide and exhaust gas recirculation on the oxidative reactivity of soot from ethylene flames and diesel engines

Science.gov (United States)

Al-Qurashi, Khalid O.

Restrictive emissions standards to reduce nitrogen oxides (NOx) and particulate matter (PM) emissions from diesel engines necessitate the development of advanced emission control technology. The engine manufacturers in the United States have implemented the exhaust gas recirculation (EGR) and diesel particulate filters (DPF) to meet the stringent emissions limits on NOx and PM, respectively. Although the EGR-DPF system is an effective means to control diesel engine emissions, there are some concerns associated with its implementation. The chief concern with this system is the DPF regenerability, which depends upon several factors, among which are the physicochemical properties of the soot. Despite the plethora of research that has been conducted on DPF regenerability, the impact of EGR on soot reactivity and DPF regenerability is yet to be examined. This work concerns the impact of EGR on the oxidative reactivity of diesel soot. It is part of ongoing research to bridge the gap in establishing a relationship between soot formation conditions, properties, and reactivity. This work is divided into three phases. In the first phase, carbon dioxide (CO2) was added to the intake charge of a single cylinder engine via cylinders of compressed CO2. This approach simulates the cold-particle-free EGR. The results showed that inclusion of CO2 changes the soot properties and yields synergistic effects on the oxidative reactivity of the resulting soot. The second phase of this research was motivated by the findings from the first phase. In this phase, post-flame ethylene soot was produced from a laboratory co-flow laminar diffusion flame to better understand the mechanism by which the CO2 affects soot reactivity. This phase was accomplished by successfully isolating the dilution, thermal, and chemical effects of the CO2. The results showed that all of these effects account for a measurable increase in soot reactivity. Nevertheless, the thermal effect was found to be the most

Vapor-liquid equilibrium data for five binary systems of methanol, tert-butylalcohol, tert-butylmethylether and water, and quaternary reactive system producing tert-butylmethylether from methanol and tert-butylalcohol; Metanoru, tert-buchiruarukoru, tert-buchirumechirueteru oyobi mizu wo kumiawaseta 5shu no niseibunkei to metanoru to tert-buchiruarukoru ni yoru eteruka hannokei no taikiatsuka ni okeru kieki heiko deta

Energy Technology Data Exchange (ETDEWEB)

Komatsu, H.; Nakamura, M.; Yamashita, Y.; Hirai, C. [Toyohashi Univ. of Technology (Japan)

1997-11-01

At atmospheric pressure, vapor-liquid equilibrium relationships for five binary systems of methanol-tert-butylalcohol, methanol-tert-butylmethylether, tert-butylalcohol-tert-butylmethylether, water-tert-butylalcohol and water-tert-butylmethylether are observed. The Wilson parameters for the binary systems have been obtained. Comparisons between the Wilson method, The ASOG method and the UNIFAC method are made. Vapor-liquid equilibrium relationships of the quaternary reactive system producing tert-butylmethylether by use of methanol and tert-butylalcohol are also observed, and it is confirmed that the Wilson parameters resulting from the data of binary systems can be used to estimate the vapor-liquid equilibrium data for the quaternary reactive system of methanol-tert-butylalcohol-tert-butylmethylether-water. 6 refs., 7 figs., 5 tabs.

SO{sub 2} retention by reactivated CaO-based sorbent from multiple CO{sub 2} capture cycles

Energy Technology Data Exchange (ETDEWEB)

Vasilije Manovic; Edward J. Anthony [CANMET Energy Technology Centre-Ottawa, Ottawa, ON (Canada). Natural Resources Canada

2007-06-15

This paper examines the reactivation of spent sorbent, produced from multiple CO{sub 2} capture cycles, for use in SO{sub 2} capture. CaO-based sorbent samples were obtained from Kelly Rock limestone using three particle size ranges, each containing different impurities levels. Using a thermogravimetric analyzer (TGA), the sulfation behavior of partially sulfated and unsulfated samples obtained after multiple calcination-carbonation cycles in a tube furnace (TF), following steam reactivation in a pressurized reactor, is examined. In addition, samples calcined/sintered under different conditions after hydration are also examined. The results show that suitably treated spent sorbent has better sulfation characteristics than that of the original sorbent. Thus for example, after 2 h sulfation, {gt} 80% of the CaO was sulfated. In addition, the sorbent showed significant activity even after 4 h when {gt} 95% CaO was sulfated. The results were confirmed by X-ray diffraction (XRD) analysis, which showed that, by the end of the sulfation process, samples contained CaSO{sub 4} with only traces of unreacted CaO. The superior behavior of spent reactivated sorbent appears to be due to swelling of the sorbent particles during steam hydration. The surface area morphology of sorbent after reactivation was examined by scanning electron microscopy (SEM). Ca(OH){sub 2} crystals were seen, which displayed their regular shape, and their elemental composition was confirmed by energy-dispersive X-ray (EDX) analysis. These results allow the proposal of a new process for the use of CaO-based sorbent in fluidized bed combustion (FBC) systems, which incorporates CO{sub 2} capture, sorbent reactivation, and SO{sub 2} retention. 26 refs., 4 figs., 2 tabs.

Poststaphylococcal coagulase negative reactive arthritis: a case report.

Science.gov (United States)

Krasniqi, Xhevdet; Rexhepi, Sylejman; Gashi, Masar; Berisha, Blerim; Abazi, Flora; Koçinaj, Dardan

2009-12-18

We report a case of a 49-year-old patient who developed poststaphylococcal coagulase negative reactive arthritis. The woman presented with constitutional symptoms, arthritis, urinary infection and conjunctivitis. The blood culture was positive for the staphylococcal coagulase negative infection. Erythrocyte sedimentation rate and C-reactive protein were elevated, whereas the rheumatoid factor was negative. Radiographic findings confirmed diagnosis of pleuropneumonia, and one year later of chronic asymmetric sacroileitis. Physicians should be aware of possible reactive arthritis after staphylococcal coagulase negative bacteremia.

Biofilm Community Dynamics in Bench-Scale Annular Reactors Simulating Arrestment of Chloraminated Drinking Water Nitrification

Science.gov (United States)

Annular reactors (ARs) were used to study biofilm community succession and provide an ecological insight during nitrification arrestment through simultaneously increasing monochloramine (NH2Cl) and chlorine to nitrogen mass ratios, resulting in four operational periods (I to IV)....

Review of Various Solutions for avoiding critical levels of Legionella Bacteria in Domestic Hot Water System

DEFF Research Database (Denmark)

Yang, Xiaochen; Li, Hongwei; Svendsen, Svend

2013-01-01

, electric boiler, compact heat exchanger, water filter, chlorine dioxide, Monochloramine, UV sterilization, copper and silver electrodes. The implementary conditions, effect, limits as well as economic performance of them are demonstrated. For buildings with complicated networks and large volume, chemical...

Reward disrupts reactivated human skill memory

OpenAIRE

Dayan, Eran; Laor-Maayany, Rony; Censor, Nitzan

2016-01-01

Accumulating evidence across species and memory domains shows that when an existing memory is reactivated, it becomes susceptible to modifications. However, the potential role of reward signals in these mechanisms underlying human memory dynamics is unknown. Leaning on a wealth of findings on the role of reward in reinforcing memory, we tested the impact of reinforcing a skill memory trace with monetary reward following memory reactivation, on strengthening of the memory trace. Reinforcing re...

Refinement of Parallel and Reactive Programs

OpenAIRE

Back, R. J. R.

1992-01-01

We show how to apply the refinement calculus to stepwise refinement of parallel and reactive programs. We use action systems as our basic program model. Action systems are sequential programs which can be implemented in a parallel fashion. Hence refinement calculus methods, originally developed for sequential programs, carry over to the derivation of parallel programs. Refinement of reactive programs is handled by data refinement techniques originally developed for the sequential refinement c...

Apparatus and method for extracting power from energetic ions produced in nuclear fusion

Science.gov (United States)

Fisch, Nathaniel J.; Rax, Jean M.

1994-01-01

An apparatus and method of extracting power from energetic ions produced by nuclear fusion in a toroidal plasma to enhance respectively the toroidal plasma current and fusion reactivity. By injecting waves of predetermined frequency and phase traveling substantially in a selected poloidal direction within the plasma, the energetic ions become diffused in energy and space such that the energetic ions lose energy and amplify the waves. The amplified waves are further adapted to travel substantially in a selected toroidal direction to increase preferentially the energy of electrons traveling in one toroidal direction which, in turn, enhances or generates a toroidal plasma current. In an further adaptation, the amplified waves can be made to preferentially increase the energy of fuel ions within the plasma to enhance the fusion reactivity of the fuel ions. The described direct, or in situ, conversion of the energetic ion energy provides an efficient and economical means of delivering power to a fusion reactor.

Transport of secondary electrons and reactive species in ion tracks

Science.gov (United States)

Surdutovich, Eugene; Solov'yov, Andrey V.

2015-08-01

The transport of reactive species brought about by ions traversing tissue-like medium is analysed analytically. Secondary electrons ejected by ions are capable of ionizing other molecules; the transport of these generations of electrons is studied using the random walk approximation until these electrons remain ballistic. Then, the distribution of solvated electrons produced as a result of interaction of low-energy electrons with water molecules is obtained. The radial distribution of energy loss by ions and secondary electrons to the medium yields the initial radial dose distribution, which can be used as initial conditions for the predicted shock waves. The formation, diffusion, and chemical evolution of hydroxyl radicals in liquid water are studied as well. COST Action Nano-IBCT: Nano-scale Processes Behind Ion-Beam Cancer Therapy.

Unexpected seasonality in quantity and composition of Amazon rainforest air reactivity.

Science.gov (United States)

Nölscher, A C; Yañez-Serrano, A M; Wolff, S; de Araujo, A Carioca; Lavrič, J V; Kesselmeier, J; Williams, J

2016-01-22

The hydroxyl radical (OH) removes most atmospheric pollutants from air. The loss frequency of OH radicals due to the combined effect of all gas-phase OH reactive species is a measureable quantity termed total OH reactivity. Here we present total OH reactivity observations in pristine Amazon rainforest air, as a function of season, time-of-day and height (0-80 m). Total OH reactivity is low during wet (10 s(-1)) and high during dry season (62 s(-1)). Comparison to individually measured trace gases reveals strong variation in unaccounted for OH reactivity, from 5 to 15% missing in wet-season afternoons to mostly unknown (average 79%) during dry season. During dry-season afternoons isoprene, considered the dominant reagent with OH in rainforests, only accounts for ∼20% of the total OH reactivity. Vertical profiles of OH reactivity are shaped by biogenic emissions, photochemistry and turbulent mixing. The rainforest floor was identified as a significant but poorly characterized source of OH reactivity.

A Reactive Robot Architecture With Planning on Demand

National Research Council Canada - National Science Library

Ranganathan, Ananth; Koenig, Sven

2003-01-01

In this paper, we describe a reactive robot architecture that uses fast re-planning methods to avoid the shortcomings of reactive navigation, such as getting stuck in box canyons or in front of small openings...

Environmental life cycle assessment of permeable reactive barriers: effects of construction methods, reactive materials and groundwater constituents.

Science.gov (United States)

Mak, Mark S H; Lo, Irene M C

2011-12-01

The effects of the construction methods, materials of reactive media and groundwater constituents on the environmental impacts of a permeable reactive barrier (PRB) were evaluated using life cycle assessment (LCA). The PRB is assumed to be installed at a simulated site contaminated by either Cr(VI) alone or Cr(VI) and As(V). Results show that the trench-based construction method can reduce the environmental impacts of the remediation remarkably compared to the caisson-based method due to less construction material consumption by the funnel. Compared to using the zerovalent iron (Fe(0)) and quartz sand mixture, the use of the Fe(0) and iron oxide-coated sand (IOCS) mixture can reduce the environmental impacts. In the presence of natural organic matter (NOM) in groundwater, the environmental impacts generated by the reactive media were significantly increased because of the higher usage of Fe(0). The environmental impacts are lower by using the Fe(0) and IOCS mixture in the groundwater with NOM, compared with using the Fe(0) and quartz sand mixture. Since IOCS can enhance the removal efficiency of Cr(VI) and As(V), the usage of the Fe(0) can be reduced, which in turn reduces the impacts induced by the reactive media.

Cement reactivity in CO2 saturated brines: use of a reactive transport code to highlight key degradation mechanisms

International Nuclear Information System (INIS)

Huet, B.M.; Prevost, J.H.; Scherer, G.W.

2007-01-01

A modular reactive transport code is proposed to analyze the reactivity of cement in CO 2 saturated brine. The coupling of the transport module and the geochemical module within Dynaflow TM is derived. Both modules are coupled in a sequential iterative approach to accurately model: (1) mineral dissolution/precipitation and (2) porosity dependent transport properties. Results of the model reproduce qualitatively the dissolution of cement hydrates (C-H, C-S-H, AFm, AFt) and intermediate products (CaCO 3 ) into the brine. Slight discrepancies between modeling and experimental results were found concerning the dynamics of the mineral zoning. Results suggest that the power law relationship to model effective transport properties from porosity values is not accurate for very reactive case. (authors)

A simple process to achieve microchannels geometries able to produce hydrodynamic cavitation

Science.gov (United States)

Qiu, X.; Cherief, W.; Colombet, D.; Ayela, F.

2017-04-01

We present a simple process to perform microchannels in which cavitating two phase flows are easily producible. Up to now, hydrodynamic cavitation ‘on a chip’ was reached with small flow rates inside microchannels whose micromachining had involved a deep reactive ion etching (D-RIE). The process we present here does not require a D-RIE reactor, as it is only funded on a wet etching of silicon. It leads to a so-called microstep profile, and large cavitating flow rates become possible together with moderate pressure drops.

A simple process to achieve microchannels geometries able to produce hydrodynamic cavitation

International Nuclear Information System (INIS)

Qiu, X; Cherief, W; Colombet, D; Ayela, F

2017-01-01

We present a simple process to perform microchannels in which cavitating two phase flows are easily producible. Up to now, hydrodynamic cavitation ‘on a chip’ was reached with small flow rates inside microchannels whose micromachining had involved a deep reactive ion etching (D-RIE). The process we present here does not require a D-RIE reactor, as it is only funded on a wet etching of silicon. It leads to a so-called microstep profile, and large cavitating flow rates become possible together with moderate pressure drops. (technical note)

Reactivity effects due to beryllium poisoning of BR2

International Nuclear Information System (INIS)

Kalcheva, S.; Ponsard, B.; Koonen, E.

2004-01-01

This paper illustrates the impact of the poisoning of the beryllium reflector on reactivity variations of the Belgian MTR BR2 in SCK.CEN. Detailed calculations by MCNP-4C of reactivity effects caused by strong neutron absorbers 3 He and 6 Li during reactor operation history are presented. The importance of beryllium poisoning for the accuracy of reactivity predictions is discussed. (authors)

Development of a faulty reactivity detection system applying a digital H∞ estimator

International Nuclear Information System (INIS)

Suzuki, Katsuo; Suzudo, Tomoaki; Nabeshima, Kunihiko

2004-01-01

This paper concerns an application of digital optimal H ∞ estimator to the detection of faulty reactivity in real-time. The detection system, fundamentally based on the reactivity balance method, is composed of three modules, i.e. the net reactivity estimator, the feedback reactivity estimator and the reactivity balance circuit. H ∞ optimal filters are used for these two reactivity estimators, and the nonlinear neutronics are taken into consideration especially for the design of the net reactivity estimator. A series of performance test of the detection system are conducted by using numerical simulations of reactor dynamics with the insertion of a faulty reactivity for an experimental fast breeder reactor JOYO. The system detects the typical artificial reactivity insertions during a few seconds with no stationary offset and the accuracy of 0.1 cent, and is satisfactory for its practical use. (author)

Fragmentation and reactivity of energy-selected ferrocenium ions

International Nuclear Information System (INIS)

Mestdagh, H.; Dutuit, O.; Heninger, M.; Thissen, R.; Alcaraz, C.

2002-01-01

In this study, results concerning the discussion of state-selected ferrocenium ions (c-C 5 H 5 ) 2 Fe + commonly called Cp 2 Fe + , as well as their reactions with methanol and ethanol are presented. Parent ions Cp 2 Fe + were produced by vacuumultraviolett (VUV) photoionization of neutral ferrocene using synchrotron radiation, and selected in internal energy by threshold photoelectron-photoion coincidences. The apparatus is divided into three differentially pumped regions: the source, the reaction and the detection zones. In source, state-selected parent ions are formed and can be selected in mass by a first quadrupole filter. State-selected ions are then injected in the second zone which is a RF octopole ion guide where reaction product ions are mass analyzed by a second quadrupole filter and detected by microchannelplates. In addition, the long flight time in the octopoles (several hundreds of microseconds) allows studying long-lived metastable ions. Total mass spectra were recorded at different photon energies, in addition to the main CpFe + and Fe + fragments, several minor fragments were detected such as C 10 H 10 + which reflects the formation of a C-C bond between the two Cp ligands. Losses of CH 3 , C 2 H 2 and C-4H 4 also indicate that important structure rearrangements take place before cleavage. The appearance energies of each mass-selected fragment ion were measured by recording fragment ion yields as a function of photon energy. Surprisingly, all fragments were found to have the same energy onset, i.e. 13.2 eV photon energy, except for C 3 H 3 Fe + (m/z 95). For Fe + ions, a sharp increase was observed at 17 eV, above the thermochemical onset of Fe + + 2 Cp. The 13.2 eV appearance energy of Fe + is thus assigned to the formation of Fe - + C 10 H 10 . The reactivity of ferrocenium ion with methanol and ethanol was investigated as a function of photon energy. While no reaction occurs at lower photon energies, several reaction products appear at 13.0 e

Reactivity of nitriles

International Nuclear Information System (INIS)

Kukushkin, Yu.N.

1987-01-01

Reactivity of coordination nitriles in transition metal (Ru, Mo, W, Zr, Hf) complexes, namely: transformation of nitriles of the first coordination sphere into N-acyl-substituted amides, amidines, nitrile interaction; with water, alkalines, alcoholes, hydrogen, azide and cyanide ions is considered. Introduction of acetonitrile molecule to uranium (4)-carbon double bond is discussed

The determination and analysis of site-specific rates of mitochondrial reactive oxygen species production

DEFF Research Database (Denmark)

Quinlan, Casey L; Perevoschikova, Irina V; Goncalves, Renata L S

2013-01-01

Mitochondrial reactive oxygen species (ROS) are widely implicated in physiological and pathological pathways. We propose that it is critical to understand the specific sites of mitochondrial ROS production and their mechanisms of action. Mitochondria possess at least eight distinct sites of ROS...... production in the electron transport chain and matrix compartment. In this chapter, we describe the nature of the mitochondrial ROS-producing machinery and the relative capacities of each site. We provide detailed methods for the measurement of H2O2 release and the conditions under which maximal rates from...

Referencing cross-reactivity of detection antibodies for protein array experiments [version 1; referees: 1 approved, 2 approved with reservations

Directory of Open Access Journals (Sweden)

Darragh Lemass

2016-01-01

Full Text Available Protein arrays are frequently used to profile antibody repertoires in humans and animals. High-throughput protein array characterisation of complex antibody repertoires requires a platform-dependent, lot-to-lot validation of secondary detection antibodies. This article details the validation of an affinity-isolated anti-chicken IgY antibody produced in rabbit and a goat anti-rabbit IgG antibody conjugated with alkaline phosphatase using protein arrays consisting of 7,390 distinct human proteins. Probing protein arrays with secondary antibodies in absence of chicken serum revealed non-specific binding to 61 distinct human proteins. The cross-reactivity of the tested secondary detection antibodies points towards the necessity of platform-specific antibody characterisation studies for all secondary immunoreagents. Secondary antibody characterisation using protein arrays enables generation of reference lists of cross-reactive proteins, which can be then excluded from analysis in follow-up experiments. Furthermore, making such cross-reactivity lists accessible to the wider research community may help to interpret data generated by the same antibodies in applications not related to protein arrays such as immunoprecipitation, Western blots or other immunoassays.

Characterizing Nanoparticles Reactivity: Structure-Photocatalytic Activity Relationship

International Nuclear Information System (INIS)

Piella, J; Bastús, N G; Casals, E; Puntes, V

2013-01-01

Nanoparticles are reactive, and their final interactions with the surrounding media are ultimately determined by their reactivity, which in turns depends on the nanoparticles morphology, surface chemistry and environment in which they are embedded. One simple and informative approach for the study of the reactivity of nanoparticles is the determination of their photocatalytic activity. In the present work, we briefly summarize the importance of different parameters such as the size, shape and agglomeration state on the photocatalytic activity of colloidal inorganic nanoparticles. The study of the use of nanoparticles as photocatalyts is relevant not only for its potential applications in environmental remediation issues but also it can provide relevant information about the role of these parameters at the nanoscale.

Effect of Changing Treatment Disinfectants on the Microbiology of Distributed Water and Pipe Biofilm Communities using Conventional and Metagenomic Approaches

Science.gov (United States)

The purpose of this research was to add to our knowledge of chlorine and monochloramine disinfectants, with regards to effects on the microbial communities in distribution systems. A whole metagenome-based approach using sophisticated molecular tools (e.g., next generation sequen...

Persistent Latent Tuberculosis Reactivation Risk in United States Immigrants

Science.gov (United States)

Painter, John; Parker, Matthew; Lowenthal, Phillip; Flood, Jennifer; Fu, Yunxin; Asis, Redentor; Reves, Randall

2014-01-01

Rationale: Current guidelines limit latent tuberculosis infection (LTBI) evaluation to persons in the United States less than or equal to 5 years based on the assumption that high TB rates among recent entrants are attributable to high LTBI reactivation risk, which declines over time. We hypothesized that high postarrival TB rates may instead be caused by imported active TB. Objectives: Estimate reactivation and imported TB in an immigrant cohort. Methods: We linked preimmigration records from a cohort of California-bound Filipino immigrants during 2001–2010 with subsequent TB reports. TB was likely LTBI reactivation if the immigrant had no evidence of active TB at preimmigration examination, likely imported if preimmigration radiograph was abnormal and TB was reported less than or equal to 6 months after arrival, and likely reactivation of inactive TB if radiograph was abnormal but TB was reported more than 6 months after arrival. Measurements and Main Results: Among 123,114 immigrants, 793 TB cases were reported. Within 1 year of preimmigration examination, 85% of TB was imported; 6 and 9% were reactivation of LTBI and inactive TB, respectively. Conversely, during Years 2–9 after U.S. entry, 76 and 24% were reactivation of LTBI and inactive TB, respectively. The rate of LTBI reactivation (32 per 100,000) did not decline during Years 1–9. Conclusions: High postarrival TB rates were caused by detection of imported TB through active postarrival surveillance. Among immigrants without active TB at baseline, reported TB did not decline over 9 years, indicating sustained high risk of LTBI reactivation. Revised guidelines should support LTBI screening and treatment more than 5 years after U.S. arrival. PMID:24308495

Correlates and consequences of toddler cortisol reactivity to fear.

Science.gov (United States)

Kiel, Elizabeth J; Kalomiris, Anne E

2016-02-01

Cortisol reactivity to fear-eliciting stimuli during toddlerhood may represent an indicator of risk for anxiety spectrum problems and other maladjustment. Thus, it is important to understand factors that may contribute to cortisol reactivity as well as those that determine its predictive relation to early emerging anxiety. In this vein, the current study investigated maternal comforting behaviors, both solicited and unsolicited by the toddler, as correlates of cortisol reactivity at 2years of age. Furthermore, we investigated maternal comforting behaviors and behavioral indicators of fear in both a low-threat and a high-threat context as moderators of the relation between cortisol reactivity at age 2 and change in anxiety from age 2 to age 3. The sample comprised 99 2-year-old toddlers and their mothers. Toddlers provided saliva samples at baseline and after a fear-eliciting stimulus that were assayed for cortisol. Mothers were observed for comforting behavior while interacting with their toddlers in laboratory tasks and completed questionnaires about their toddlers' anxiety. Results indicated that unsolicited (spontaneous) comforting behavior related to toddler cortisol reactivity above and beyond solicited comforting and the level of fear toddlers displayed in the same task. Moreover, fear in a low-threat context, but not in a high-threat context, moderated the relation between cortisol reactivity and change in anxiety, such that cortisol reactivity had a positive relation to anxiety at extreme levels of low-threat fear. Results suggest the importance of considering the caregiving environment and context-specific fear in understanding the nature of cortisol reactivity during the toddler years. Copyright © 2015 Elsevier Inc. All rights reserved.

Awake reactivation predicts memory in humans

OpenAIRE

Staresina, Bernhard P.; Alink, Arjen; Kriegeskorte, Nikolaus; Henson, Richard N.

2013-01-01

How is new information converted into a memory trace? Here, we used functional neuroimaging to assess what happens to representations of new events after we first experience them. We found that a particular part of the medial temporal lobe, a brain region known to be critical for intact memory, spontaneously reactivates these events even when we are engaged in unrelated activities. Indeed, the extent to which such automatic reactivation occurs seems directly related to later memory performanc...

A comparison of herpes simplex virus type 1 and varicella-zoster virus latency and reactivation.

Science.gov (United States)

Kennedy, Peter G E; Rovnak, Joel; Badani, Hussain; Cohrs, Randall J

2015-07-01

Herpes simplex virus type 1 (HSV-1; human herpesvirus 1) and varicella-zoster virus (VZV; human herpesvirus 3) are human neurotropic alphaherpesviruses that cause lifelong infections in ganglia. Following primary infection and establishment of latency, HSV-1 reactivation typically results in herpes labialis (cold sores), but can occur frequently elsewhere on the body at the site of primary infection (e.g. whitlow), particularly at the genitals. Rarely, HSV-1 reactivation can cause encephalitis; however, a third of the cases of HSV-1 encephalitis are associated with HSV-1 primary infection. Primary VZV infection causes varicella (chickenpox) following which latent virus may reactivate decades later to produce herpes zoster (shingles), as well as an increasingly recognized number of subacute, acute and chronic neurological conditions. Following primary infection, both viruses establish a latent infection in neuronal cells in human peripheral ganglia. However, the detailed mechanisms of viral latency and reactivation have yet to be unravelled. In both cases latent viral DNA exists in an 'end-less' state where the ends of the virus genome are joined to form structures consistent with unit length episomes and concatemers, from which viral gene transcription is restricted. In latently infected ganglia, the most abundantly detected HSV-1 RNAs are the spliced products originating from the primary latency associated transcript (LAT). This primary LAT is an 8.3 kb unstable transcript from which two stable (1.5 and 2.0 kb) introns are spliced. Transcripts mapping to 12 VZV genes have been detected in human ganglia removed at autopsy; however, it is difficult to ascribe these as transcripts present during latent infection as early-stage virus reactivation may have transpired in the post-mortem time period in the ganglia. Nonetheless, low-level transcription of VZV ORF63 has been repeatedly detected in multiple ganglia removed as close to death as possible. There is increasing

Impact of reactive settler models on simulated WWTP performance

DEFF Research Database (Denmark)

Gernaey, Krist; Jeppsson, Ulf; Batstone, Damien J.

2006-01-01

for an ASM1 case study. Simulations with a whole plant model including the non-reactive Takacs settler model are used as a reference, and are compared to simulation results considering two reactive settler models. The first is a return sludge model block removing oxygen and a user-defined fraction of nitrate......, combined with a non-reactive Takacs settler. The second is a fully reactive ASM1 Takacs settler model. Simulations with the ASM1 reactive settler model predicted a 15.3% and 7.4% improvement of the simulated N removal performance, for constant (steady-state) and dynamic influent conditions respectively....... The oxygen/nitrate return sludge model block predicts a 10% improvement of N removal performance under dynamic conditions, and might be the better modelling option for ASM1 plants: it is computationally more efficient and it will not overrate the importance of decay processes in the settler....

Does reactivation trigger episodic memory change? A meta-analysis.

Science.gov (United States)

Scully, Iiona D; Napper, Lucy E; Hupbach, Almut

2017-07-01

According to the reconsolidation hypothesis, long-term memories return to a plastic state upon their reactivation, leaving them vulnerable to interference effects and requiring re-storage processes or else these memories might be permanently lost. The present study used a meta-analytic approach to critically evaluate the evidence for reactivation-induced changes in human episodic memory. Results indicated that reactivation makes episodic memories susceptible to physiological and behavioral interference. When applied shortly after reactivation, interference manipulations altered the amount of information that could be retrieved from the original learning event. This effect was more pronounced for remote memories and memories of narrative structure. Additionally, new learning following reactivation reliably increased the number of intrusions from new information into the original memory. These findings support a dynamic view of long-term memory by showing that memories can be changed long after they were acquired. Copyright © 2016 Elsevier Inc. All rights reserved.

Total OH Reactivity Measurements in the Boreal Forest

Science.gov (United States)

Praplan, A. P.; Hellén, H.; Hakola, H.; Hatakka, J.

2015-12-01

INTRODUCTION Atmospheric total OH reactivity (Rtotal) can be measured (Kovacs and Brune, 2001; Sinha et al., 2008) or it can be calculated according to Rtotal = ∑i kOH+X_i [Xi] where kOH+X_i corresponds to the reaction rate coefficient for the reaction of OH with a given compound Xi and [Xi] its concentration. Studies suggest that in some environments a large fraction of missing reactivity, comparing calculated Rtotal with ambient total OH reactivity measurements (Di Carlo et al., 2004; Hofzumahaus et al., 2009). In this study Rtotal has been measured using the Comparative Reactivity Method (Sinha et al., 2008). Levels of the reference compound (pyrrole, C4H5N) are monitored by gas chromatography every 2 minutes and Rtotal is derived from the difference of reactivity between zero and ambient air. RESULTS Around 36 hours of preliminary total OH reactivity data (30 May until 2 June 2015) are presented in Fig. 1. Its range matches previous studies for this site (Nölscher et al., 2012; Sinha et al., 2010) and is similar to values in another pine forest (Nakashima et al., 2014). The setup used during the period presented here has been updated and more recent data will be presented, as well as a comparison with calculated OH reactivity from measured individual species. ACKNOWLEDGEMENTS This work was supported by Academy of Finland (Academy Research Fellowship No. 275608). The authors acknowledge Juuso Raine for technical support. REFERENCES Di Carlo et al. (2004). Science 304, 722-725.Hofzumahaus et al. (2009). Science 324, 1702-1704.Kovacs and Brune (2001). J. Atmos. Chem. 39, 105-122.Nakashima et al. (2014). Atmos. Env. 85, 1-8.Nölscher et al. (2012). Atmos. Chem. Phys. 12, 8257-8270.Sinha et al. (2008). Atmos. Chem. Phys. 8, 2213-2227.Sinha et al. (2010). Environ. Sci. Technol. 44, 6614-6620.

Sleep Reactivity and Insomnia: Genetic and Environmental Influences

Science.gov (United States)

Drake, Christopher L.; Friedman, Naomi P.; Wright, Kenneth P.; Roth, Thomas

2011-01-01

Study Objectives: Determine the genetic and environmental contributions to sleep reactivity and insomnia. Design: Population-based twin cohort. Participants: 1782 individual twins (988 monozygotic or MZ; 1,086 dizygotic or DZ), including 744 complete twin pairs (377 MZ and 367 DZ). Mean age was 22.5 ± 2.8 years; gender distribution was 59% women. Measurements: Sleep reactivity was measured using the Ford Insomnia Response to Stress Test (FIRST). The criterion for insomnia was having difficulty falling asleep, staying asleep, or nonrefreshing sleep “usually or always” for ≥ 1 month, with at least “somewhat” interference with daily functioning. Results: The prevalence of insomnia was 21%. Heritability estimates for sleep reactivity were 29% for females and 43% for males. The environmental variance for sleep reactivity was greater for females and entirely due to nonshared effects. Insomnia was 43% to 55% heritable for males and females, respectively; the sex difference was not significant. The genetic variances in insomnia and FIRST scores were correlated (r = 0.54 in females, r = 0.64 in males), as were the environmental variances (r = 0.32 in females, r = 0.37 in males). In terms of individual insomnia symptoms, difficulty staying asleep (25% to 35%) and nonrefreshing sleep (34% to 35%) showed relatively more genetic influences than difficulty falling asleep (0%). Conclusions: Sleep reactivity to stress has a substantial genetic component, as well as an environmental component. The finding that FIRST scores and insomnia symptoms share genetic influences is consistent with the hypothesis that sleep reactivity may be a genetic vulnerability for developing insomnia. Citation: Drake CL; Friedman NP; Wright KP; Roth T. Sleep reactivity and insomnia: genetic and environmental influences. SLEEP 2011;34(9):1179-1188. PMID:21886355

Identification of innovative potential quality markers in rocket and melon fresh-cut produce.

Science.gov (United States)

Cavaiuolo, Marina; Cocetta, Giacomo; Bulgari, Roberta; Spinardi, Anna; Ferrante, Antonio

2015-12-01

Ready-to-eat fresh cut produce are exposed to pre- and postharvest abiotic stresses during the production chain. Our work aimed to identify stress responsive genes as new molecular markers of quality that can be widely applied to leaves and fruits and easily determined at any stage of the production chain. Stress responsive genes associated with quality losses were isolated in rocket and melon fresh-cut produce and their expression levels analyzed by quantitative real time PCR (qRT-PCR) at different time points after harvest at 20 °C and 4 °C. qRT-PCR results were supported by correlation analysis with physiological and biochemical determinations evaluated at the same conditions such as chlorophyll a fluorescence indices, total, reducing sugars, sucrose, ethylene, ascorbic acid, lipid peroxidation and reactive oxygen species. In both species the putative molecular markers increased their expression soon after harvest suggesting a possible use as novel and objective quality markers of fresh-cut produces. Copyright © 2015 Elsevier Ltd. All rights reserved.

Affective reactivity differences in pregnant and postpartum women.

Science.gov (United States)

Rosebrock, Laina; Hoxha, Denada; Gollan, Jackie

2015-06-30

Reactions to emotional cues, termed affective reactivity, promote adaptation and survival. Shifts in affective reactivity during pregnancy and postpartum may invoke altered responses to environmental and biological changes. The development and testing of affective reactivity tasks, with published normative ratings for use in studies of affective reactivity, has been based on responses provided by healthy college students. A comparison of the healthy norms with ratings provided by peripartum women has yet to be conducted, despite its value in highlighting critical differences in affective reactivity during peripartum phases. This study compared arousal ratings of unpleasant, neutral, pleasant, and threat stimuli from the International Affective Picture System (IAPS; Lang, P.J., Bradley, M.M., Cuthbert, B.N. 2008. International Affective Picture System (IAPS): Affective Ratings of Pictures and Instruction Manual (Technical Report A-8). University of Florida, Gainseville, FL.) between three samples: (a) women measured during pregnancy and again at postpartum, (b) age-matched nonpregnant women, and (c) college-aged women from the normative sample used to test the stimuli. Using mixed-design GLMs, results showed that the pregnant and postpartum women and the age-matched women showed suppressed arousal relative to the college-age women. Additionally, postpartum women showed increased arousal to unpleasant/threat images compared to other types of images. The data suggest that future research on peripartum women should include affective reactivity tasks based on norms reflective of this specific population. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Dynamic Reactive Power Control in Offshore HVDC Connected Wind Power Plants

DEFF Research Database (Denmark)

Sakamuri, Jayachandra N.; Cutululis, Nicolaos Antonio; Rather, Zakir Hussain

2016-01-01

This paper presents a coordinated reactive power control for a HVDC connected cluster of offshore wind power plants (WPPs). The reactive power reference for the WPP cluster is estimated by an optimization algorithm aiming at minimum active power losses in the offshore AC Grid. For each optimal......, such as wind turbine (WT) terminal, collector cable, and export cable, on the dynamic voltage profile of the offshore grid is investigated. Furthermore, the dynamic reactive power contribution from WTs from different WPPs of the cluster for such faults has also been studied....... reactive power set point, the OWPP cluster controller generates reactive power references for each WPP which further sends the AC voltage/ reactive power references to the associated WTs based on their available reactive power margin. The impact of faults at different locations in the offshore grid...

Temporal discounting and heart rate reactivity to stress.

Science.gov (United States)

Diller, James W; Patros, Connor H G; Prentice, Paula R

2011-07-01

Temporal discounting is the reduction of the value of a reinforcer as a function of increasing delay to its presentation. Impulsive individuals discount delayed consequences more rapidly than self-controlled individuals, and impulsivity has been related to substance abuse, gambling, and other problem behaviors. A growing body of literature has identified biological correlates of impulsivity, though little research to date has examined relations between delay discounting and markers of poor health (e.g., cardiovascular reactivity to stress). We evaluated the relation between one aspect of impulsivity, measured using a computerized temporal discounting task, and heart rate reactivity, measured as a change in heart rate from rest during a serial subtraction task. A linear regression showed that individuals who were more reactive to stress responded more impulsively (i.e., discounted delayed reinforcers more rapidly). When results were stratified by gender, the effect was observed for females, but not for males. This finding supports previous research on gender differences in cardiovascular reactivity and suggests that this type of reactivity may be an important correlate of impulsive behavior. Copyright © 2011 Elsevier B.V. All rights reserved.

Evolution and Reactivity in the Semantic Web

Science.gov (United States)

Alferes, José Júlio; Eckert, Michael; May, Wolfgang

Evolution and reactivity in the Semantic Web address the vision and concrete need for an active Web, where data sources evolve autonomously and perceive and react to events. In 2004, when the Rewerse project started, regarding work on Evolution and Reactivity in the Semantic Web there wasn’t much more than a vision of such an active Web.

Neural mechanisms of reactivation-induced updating that enhance and distort memory.

Science.gov (United States)

St Jacques, Peggy L; Olm, Christopher; Schacter, Daniel L

2013-12-03

We remember a considerable number of personal experiences because we are frequently reminded of them, a process known as memory reactivation. Although memory reactivation helps to stabilize and update memories, reactivation may also introduce distortions if novel information becomes incorporated with memory. Here we used functional magnetic resonance imaging (fMRI) to investigate the neural mechanisms mediating reactivation-induced updating in memory for events experienced during a museum tour. During scanning, participants were shown target photographs to reactivate memories from the museum tour followed by a novel lure photograph from an alternate tour. Later, participants were presented with target and lure photographs and asked to determine whether the photographs showed a stop they visited during the tour. We used a subsequent memory analysis to examine neural recruitment during reactivation that was associated with later true and false memories. We predicted that the quality of reactivation, as determined by online ratings of subjective recollection, would increase subsequent true memories but also facilitate incorporation of the lure photograph, thereby increasing subsequent false memories. The fMRI results revealed that the quality of reactivation modulated subsequent true and false memories via recruitment of left posterior parahippocampal, bilateral retrosplenial, and bilateral posterior inferior parietal cortices. However, the timing of neural recruitment and the way in which memories were reactivated contributed to differences in whether memory reactivation led to distortions or not. These data reveal the neural mechanisms recruited during memory reactivation that modify how memories will be subsequently retrieved, supporting the flexible and dynamic aspects of memory.

plasmatis Center for Innovation Competence: Controlling reactive component output of atmospheric pressure plasmas in plasma medicine

Science.gov (United States)

Reuter, Stephan

2012-10-01

The novel approach of using plasmas in order to alter the local chemistry of cells and cell environment presents a significant development in biomedical applications. The plasmatis center for innovation competence at the INP Greifswald e.V. performs fundamental research in plasma medicine in two interdisciplinary research groups. The aim of our plasma physics research group ``Extracellular Effects'' is (a) quantitative space and time resolved diagnostics and modelling of plasmas and liquids to determine distribution and composition of reactive species (b) to control the plasma and apply differing plasma source concepts in order to produce a tailored output of reactive components and design the chemical composition of the liquids/cellular environment and (c) to identify and understand the interaction mechanisms of plasmas with liquids and biological systems. Methods to characterize the plasma generated reactive species from plasma-, gas- and liquid phase and their biological effects will be presented. The diagnostic spectrum ranges from absorption/emission/laser spectroscopy and molecular beam mass spectrometry to electron paramagnetic resonance spectroscopy and cell biological diagnostic techniques. Concluding, a presentation will be given of the comprehensive approach to plasma medicine in Greifswald where the applied and clinical research of the Campus PlasmaMed association is combined with the fundamental research at plasmatis center.

Tunable reactivity of supported single metal atoms by impurity engineering of the MgO(001) support.

Science.gov (United States)

Pašti, Igor A; Johansson, Börje; Skorodumova, Natalia V

2018-02-28

Development of novel materials may often require a rational use of high price components, like noble metals, in combination with the possibility to tune their properties in a desirable way. Here we present a theoretical DFT study of Au and Pd single atoms supported by doped MgO(001). By introducing B, C and N impurities into the MgO(001) surface, the interaction between the surface and the supported metal adatoms can be adjusted. Impurity atoms act as strong binding sites for Au and Pd adatoms and can help to produce highly dispersed metal particles. The reactivity of metal atoms supported by doped MgO(001), as probed by CO, is altered compared to their counterparts on pristine MgO(001). We find that Pd atoms on doped MgO(001) are less reactive than on perfect MgO(001). In contrast, Au adatoms bind CO much more strongly when placed on doped MgO(001). In the case of Au on N-doped MgO(001) we find that charge redistribution between the metal atom and impurity takes place even when not in direct contact, which enhances the interaction of Au with CO. The presented results suggest possible ways for optimizing the reactivity of oxide supported metal catalysts through impurity engineering.

Reactive power control with CHP plants - A demonstration

DEFF Research Database (Denmark)

Nyeng, Preben; Østergaard, Jacob; Andersen, Claus A.

2010-01-01

power rating of 7.3 MW on two synchronous generators. A closed-loop control is implemented, that remote controls the CHP plant to achieve a certain reactive power flow in a near-by substation. The solution communicates with the grid operator’s existing SCADA system to obtain measurements from...... lines to underground cables has changed the reactive power balance, and third, the TSO has introduced restrictions in the allowed exchange of reactive power between the transmission system and distribution grids (known as the Mvar-arrangement). The demonstration includes a CHP plant with an electric......In this project the potential for ancillary services provision by distributed energy resources is investigated. Specifically, the provision of reactive power control by combined heat and power plants is examined, and the application of the new standard for DER communication systems, IEC 61850...

Porphyromonas endodontalis reactivates latent Epstein-Barr virus.

Science.gov (United States)

Makino, K; Takeichi, O; Imai, K; Inoue, H; Hatori, K; Himi, K; Saito, I; Ochiai, K; Ogiso, B

2018-06-01

To determine whether Porphyromonas endodontalis can reactivate latent Epstein-Barr virus (EBV). The concentrations of short-chain fatty acids (SCFAs) in P. endodontalis culture supernatants were determined using high-performance liquid chromatography. A promoter region of BamHI fragment Z leftward open reading frame 1 (BZLF-1), which is a transcription factor that controls the EBV lytic cycle, was cloned into luciferase expression vectors. Then, the luciferase assay was performed using P. endodontalis culture supernatants. Histone acetylation using Daudi cells treated with P. endodontalis culture supernatants was examined using Western blotting. BZLF-1 mRNA and BamHI fragment Z EB replication activator (ZEBRA) protein were also detected quantitatively using real-time polymerase chain reaction (PCR) and Western blotting. Surgically removed periapical granulomas were examined to detect P. endodontalis, EBV DNA, and BZLF-1 mRNA expression using quantitative real-time PCR. Statistical analysis using Steel tests was performed. The concentrations of n-butyric acid in P. endodontalis culture supernatants were significantly higher than those of other SCFAs (P=0.0173). Using B-95-8-221 Luc cells treated with P. endodontalis culture supernatants, the luciferase assay demonstrated that P. endodontalis induced BZLF-1 expression. Hyperacetylation of histones was also observed with the culture supernatants. BZLF-1 mRNA and ZEBRA protein were expressed by Daudi cells in a dose-dependent manner after the treatment with P. endodontalis culture supernatants. P. endodontalis and BZLF-1 in periapical granulomas were also detected. The expression levels of BZLF-1 mRNA were similar to the numbers of P. endodontalis cells in each specimen. n-butyric acid produced by P. endodontalis reactivated latent EBV. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Decreased reactivation of a herpes simplex virus type 1 (HSV-1) latency associated transcript (LAT) mutant using the in vivo mouse UV-B model of induced reactivation

Science.gov (United States)

BenMohamed, Lbachir; Osorio, Nelson; Srivastava, Ruchi; Khan, Arif A.; Simpson, Jennifer L.; Wechsler, Steven L.

2015-01-01

Blinding ocular herpetic disease in humans is due to herpes simplex virus type 1 (HSV-1) reactivations from latency, rather than to primary acute infection. The cellular and molecular mechanisms that control the HSV-1 latency-reactivation cycle remain to be fully elucidated. The aim of this study was to determine if reactivation of the HSV-1 latency associated transcript (LAT) deletion mutant (dLAT2903) was impaired in this model, as it is in the rabbit model of induced and spontaneous reactivation and in the explant TG induced reactivation model in mice. The eyes of mice latently infected with wild type HSV-1 strain McKrae (LAT(+) virus) or dLAT2903 (LAT(−) virus) were irradiated with UV-B and reactivation was determined. We found that compared to LAT(−) virus, LAT(+) virus reactivated at a higher rate as determined by shedding of virus in tears on days 3 to 7 after UV-B treatment. Thus, the UV-B induced reactivation model of HSV-1 appears to be a useful small animal model for studying the mechanisms involved in how LAT enhances the HSV-1 reactivation phenotype. The utility of the model for investigating the immune evasion mechanisms regulating the HSV-1 latency/reactivation cycle and for testing the protective efficacy of candidate therapeutic vaccines and drugs are discussed. PMID:26002839

Reactivity balance for a soluble boron-free small modular reactor

Directory of Open Access Journals (Sweden)

Lezani van der Merwe

2018-06-01

Full Text Available Elimination of soluble boron from reactor design eliminates boron-induced reactivity accidents and leads to a more negative moderator temperature coefficient. However, a large negative moderator temperature coefficient can lead to large reactivity feedback that could allow the reactor to return to power when it cools down from hot full power to cold zero power. In soluble boron-free small modular reactor (SMR design, only control rods are available to control such rapid core transient.The purpose of this study is to investigate whether an SMR would have enough control rod worth to compensate for large reactivity feedback. The investigation begins with classification of reactivity and completes an analysis of the reactivity balance in each reactor state for the SMR model.The control rod worth requirement obtained from the reactivity balance is a minimum control rod worth to maintain the reactor critical during the whole cycle. The minimum available rod worth must be larger than the control rod worth requirement to manipulate the reactor safely in each reactor state. It is found that the SMR does have enough control rod worth available during rapid transient to maintain the SMR at subcritical below k-effectives of 0.99 for both hot zero power and cold zero power. Keywords: Control Rod Worth, Reactivity Balance, Reactivity Feedback, Small Modular Reactor, Soluble Boron Free

Measurements of reactive nitrogen produced by tropical thunderstorms during BIBLE-C

Science.gov (United States)

Koike, M.; Kondo, Y.; Kita, K.; Takegawa, N.; Nishi, N.; Kashihara, T.; Kawakami, S.; Kudoh, S.; Blake, D.; Shirai, T.; Liley, B.; Ko, M.; Miyazaki, Y.; Kawasaki, Z.; Ogawa, T.

2007-09-01

The Biomass Burning and Lightning Experiment phase C (BIBLE-C) aircraft mission was carried out near Darwin, Australia (12°S, 131°E) in December 2000. This was the first aircraft experiment designed to estimate lightning NO production rates in the tropics, where production is considered to be most intense. During the two flights (flights 10 and 13 made on December 9 and 11-12, respectively) enhancements of NOx (NO + NO2) up to 1000 and 1600 parts per trillion by volume (pptv, 10-s data) were observed at altitudes between 11.5 and 14 km. The Geostationary Meteorological Satellite (GMS) cloud (brightness temperature) data and ground-based lightning measurements by the Global Positioning and Tracking System (GPATS) indicate that there were intensive lightning events over the coast of the Gulf of Carpentaria, which took place upstream from our measurement area 10 to 14 h prior to the measurements. For these two flights, air in which NOx exceeded 100 pptv extended over 620 × 140 and 400 × 170 km2 (wind direction × perpendicular direction), respectively, suggesting a significant impact of lightning NO production on NOx levels in the tropics. We estimate the amount of NOx observed between 11.5 and 14 km produced by the thunderstorms to be 3.3 and 1.8 × 1029 NO molecules for flights 10 and 13, respectively. By using the GPATS lightning flash count data, column NO production rates are estimated to be 1.9-4.4 and 21-49 × 1025 NO molecules per single flash for these two flight data sets. In these estimations, it is assumed that the column NO production between 0 and 16 km is greater than the observed values between 11.5 and 14 km by a factor of 3.2, which is derived using results reported by Pickering et al. (1998). There are however large uncertainties in the GPATS lightning data in this study and care must be made when the production rates are referred. Uncertainties in these estimates are discussed. The impact on the ozone production rate is also described.

TP1 - A computer program for the calculation of reactivity and kinetic parameters by one-dimensional neutron transport perturbation theory

International Nuclear Information System (INIS)

Kobayashi, K.

1979-03-01

TP1, a FORTRAN-IV program based on transport theory, has been developed to determine reactivity effects and kinetic parameters such as effective delayed neutron fractions and mean generation time by applying the usual perturbation formalism for one-dimensional geometry. Direct and adjoint angular dependent neutron fluxes are read from an interface file prepared by using the one-dimensional Ssub(n)-code DTK which provides options for slab, cylindrical and spherical geometry. Multigroup cross sections which are equivalent to those of the DTK-calculations are supplied in the SIGM-block which is also read from an interface file. This block which is usually produced by the code GRUCAL should contain the necessary delayed neutron data, which can be added to the original SIGMN-block by using the code SIGMUT. Two perturbation options are included in TP1: a) the usual first oder perturbation theory can be applied to determine probe reactivities, b) assuming that there are available direct fluxes for the unperturbed reactor system and adjoint fluxes for the perturbed system, the exact reactivity effect induced by the perturbation can be determined by an exact perturbation calculation. According to the input specifications, the output lists the reactivity contributions for each neutron reaction process in the desired detailed spatial and energy group resolution. (orig./RW) [de

Hepatitis B virus reactivation during immunosuppressive therapy: Appropriate risk stratification.

Science.gov (United States)

Seto, Wai-Kay

2015-04-28

Our understanding of hepatitis B virus (HBV) reactivation during immunosuppresive therapy has increased remarkably during recent years. HBV reactivation in hepatitis B surface antigen (HBsAg)-positive individuals has been well-described in certain immunosuppressive regimens, including therapies containing corticosteroids, anthracyclines, rituximab, antibody to tumor necrosis factor (anti-TNF) and hematopoietic stem cell transplantation (HSCT). HBV reactivation could also occur in HBsAg-negative, antibody to hepatitis B core antigen (anti-HBc) positive individuals during therapies containing rituximab, anti-TNF or HSCT.For HBsAg-positive patients, prophylactic antiviral therapy is proven to the effective in preventing HBV reactivation. Recent evidence also demonstrated entecavir to be more effective than lamivudine in this aspect. For HBsAg-negative, anti-HBc positive individuals, the risk of reactivations differs with the type of immunosuppression. For rituximab, a prospective study demonstrated the 2-year cumulative risk of reactivation to be 41.5%, but prospective data is still lacking for other immunosupressive regimes. The optimal management in preventing HBV reactivation would involve appropriate risk stratification for different immunosuppressive regimes in both HBsAg-positive and HBsAg-negative, anti-HBc positive individuals.

Spatially Resolved Quantification of the Surface Reactivity of Solid Catalysts.

Science.gov (United States)

Huang, Bing; Xiao, Li; Lu, Juntao; Zhuang, Lin

2016-05-17

A new property is reported that accurately quantifies and spatially describes the chemical reactivity of solid surfaces. The core idea is to create a reactivity weight function peaking at the Fermi level, thereby determining a weighted summation of the density of states of a solid surface. When such a weight function is defined as the derivative of the Fermi-Dirac distribution function at a certain non-zero temperature, the resulting property is the finite-temperature chemical softness, termed Fermi softness (SF ), which turns out to be an accurate descriptor of the surface reactivity. The spatial image of SF maps the reactive domain of a heterogeneous surface and even portrays morphological details of the reactive sites. SF analyses reveal that the reactive zones on a Pt3 Y(111) surface are the platinum sites rather than the seemingly active yttrium sites, and the reactivity of the S-dimer edge of MoS2 is spatially anisotropic. Our finding is of fundamental and technological significance to heterogeneous catalysis and industrial processes demanding rational design of solid catalysts. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Matrix-reinforcement reactivity in P/M titanium matrix composites

International Nuclear Information System (INIS)

Amigo, V.; Romero, F.; Salvador, M. D.; Busquets, D.

2007-01-01

The high reactivity of titanium and the facility of the same one to form intermetallics makes difficult obtaining composites with this material and brings the need in any case of covering the principal fibres used as reinforcement. To obtain composites of titanium reinforced with ceramic particles ins proposed in this paper, for this reason it turns out to be fundamental to evaluate the reactivity between the matrix and reinforcement. Both titanium nitride and carbide (TiN and TiC) are investigated as materials of low reactivity whereas titanium silicide (TiSi 2 ) is also studied as materials of major reactivity, already stated by the scientific community. This reactivity will be analysed by means of scanning electron microscopy (SEM) there being obtained distribution maps of the elements that allow to establish the possible influence of the sintering temperature and time. Hereby the matrix-reinforcement interactions are optimized to obtain suitable mechanical properties. (Author) 39 refs

Reactivity anomalies in the FFTF [Fast Flux Test Facility