WorldWideScience

Sample records for monitoring project stage

  1. Flight Systems Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR Phase I project will develop the Flight System Monitor which will use non-intrusive electrical monitoring (NEMO). The electronic system health of...

  2. Spacecraft Power Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR Phase I project will develop the Spacecraft Power Monitor (SPM) which will use non-intrusive electrical monitoring (NEMO). NEMO transforms the power...

  3. Aerospace Systems Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Proposal Title: Aerospace Systems Monitor PHASE 1 Technical Abstract: This Phase II STTR project will continue development and commercialization of the Aerospace...

  4. Aerospace Systems Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Phase I STTR project will demonstrate the Aerospace System Monitor (ASM). This technology transforms the power distribution network in a spacecraft or aircraft...

  5. Islay LIMPET project monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Heath, T.

    2002-07-01

    Wavegen was contracted by the DTI as part of its Sustainable Energy Programmes to monitor and report on the final stages of the construction, installation of turbo-generation equipment, commissioning and operation of the LIMPET wave energy system. The report discusses the choice of technology, where the system was installed, power take off, construction of the collector, installation of the turbo-generator, maintenance, operation, management and planning issues. The performance of the system was found to be poorer than expected and the reasons for this were identified. The main conclusions were that the system is sufficiently robust to operate in the marine environment and downtimes are expected to be short.

  6. Monitoring the effectiveness evaluation of investment projects

    Directory of Open Access Journals (Sweden)

    Skopin Alex O.

    2012-02-01

    Full Text Available The article raised the question of monitoring regulatory evaluation of the effectiveness of regional investment projects. This is justified by the fact that the current regulatory framework defined indicators for measuring the effectiveness of regional investment projects, but these figures are usually used only at the design stage of the project, an interim assessment of the effectiveness of a sufficiently simplified and based on the level of exploration investment.

  7. Lunar Health Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — During the Phase II Lunar Health Monitor program, Orbital Research will develop a second generation wearable sensor suite for astronaut physiologic monitoring. The...

  8. Lunar Health Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Orbital Research has successfully demonstrated a dry electrode (no electrolyte or gel required) for heart rate and ECG monitoring. Preliminary data has indicated...

  9. Multispectral Particle Absorption Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Small Business Innovation Research Phase II project concerns the development of a multi-wavelength monitor that will provide rapid, real-time measurement of the...

  10. Multispectral Particle Absorption Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Small Business Innovation Research Phase I project concerns the development of a multi-wavelength monitor that will provide rapid, real-time measurement of the...

  11. Nuclear Cryogenic Propulsion Stage Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Key NCPS project objectives are to conduct preliminary design, fabrication, and test of representative fuel samples and partial length fuel elements for the two...

  12. Southern Fine Particulate Monitoring Project

    Energy Technology Data Exchange (ETDEWEB)

    Ashley Williamson

    2003-05-31

    This final project report presents experimental details, results and analysis of continuous onsite ambient fine particulate data at the North Birmingham sampling site during the October, 2001-September, 2002 study period.The host site for these measurement activities is the North Birmingham PM monitoring station by the Jefferson County Health Department in Birmingham, AL.The continuous data include PM{sub 2.5} mass concentrations measured by TEOM, particle sulfate using the R&P 8400S monitor, particle size distributions measured by SMPS and APS monitors, and PM{sub 2.5} light scattering extinction coefficient as measured by nephelometer. During the course of the project, measurement intercomparison data were developed for these instruments and several complementary measurements at the site. The report details the instrument set and operating procedures and describes the resulting data. Report subsections present an overview summary of the data, followed by detailed description of the systematic time behavior of PM{sub 2.5} and other specific particulate size fractions. Specific subsections are included for particle size distribution, light scattering, and particle sulfate data. The final subsection addresses application of the measurements to the practical questions of fine PM generation and transport, source attribution, and PM{sub 2.5} management strategies.

  13. Integrated monitoring plan for the Hanford groundwater monitoring project

    Energy Technology Data Exchange (ETDEWEB)

    Hartman, M.J.; Dresel, P.E.; McDonald, J.P.; Mercer, R.B.; Newcomer, D.R.; Thornton, E.C.

    1998-09-01

    Groundwater is monitored in hundreds of wells at the Hanford Site to fulfill a variety of requirements. Separate monitoring plans are prepared for various requirements, but sampling is coordinated and data are shared among users to avoid duplication of effort. The US Department of Energy (DOE) manages these activities through the Hanford Groundwater Monitoring Project (groundwater project), which is the responsibility of Pacific Northwest National Laboratory. The groundwater project does not include all of the monitoring to assess performance of groundwater remediation or all monitoring associated with active facilities. This document is the first integrated monitoring plan for the groundwater project and contains: well and constituent lists for monitoring required by the Atomic Energy Act of 1954 and its implementing orders; other, established monitoring plans by reference; and a master well/constituent/frequency matrix for the entire Hanford Site.

  14. BPA genetic monitoring - BPA Genetic Monitoring Project

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Initiated in 1989, this study monitors genetic changes associated with hatchery propagation in multiple Snake River sub-basins for Chinook salmon and steelhead. We...

  15. Adverse event detection, monitoring, and evaluation Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR project delivers a single-sensor structural health-monitoring (SHM) system that uses the impedance method to monitor structural integrity, wave propagation...

  16. Volunteers for Air Monitoring Project (VAMP).

    Science.gov (United States)

    Oak Ridge National Lab., TN.

    An education and communication project of the Environment and Technology Assessment Program, Oak Ridge National Laboratory, Tennessee, is described in this report. The project for monitoring air dustfall resulted in the largest citizen-scientist air monitoring effort in the history of our nation. Nearly 21,000 public secondary school students and…

  17. Spacecraft Cabin Particulate Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to design, build and test an optical extinction monitor for the detection of spacecraft cabin particulates. This monitor will be sensitive to particle...

  18. Wearable Health Monitoring Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this proposal is to demonstrate the feasibility of producing a wearable health monitoring system for the human body that is functional, comfortable,...

  19. Spacecraft Cabin Particulate Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We have built and tested an optical extinction monitor for the detection of spacecraft cabin particulates. This sensor sensitive to particle sizes ranging from a few...

  20. Crew Cerebral Oxygen Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Phase II SBIR proposal is aimed at developing a non-invasive, optical method for monitoring crew member state of awareness in operational environments. All...

  1. Crew Cerebral Oxygen Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Phase I SBIR proposal is aimed at developing a non-invasive, optical method for monitoring the state of consciousness of crew members in operational...

  2. Wearable Health Monitoring Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this proposal is to demonstrate the feasibility of producing a wearable health monitoring system for the human body that is functional, comfortable,...

  3. Introduction to Meridian Space Weather Monitoring Project

    Institute of Scientific and Technical Information of China (English)

    WU Ji; WANG Chi; FAN Quanlin

    2006-01-01

    The Meridian Project is a ground- based network program to monitor solar-terrestrial space environment, which consists of a chain of ground-based observatories with multiple instruments including magnetometers, ionosondes, HF and VHF radar, Lidar, IPS monitors, sounding rockets etc. The chain is mainly located in the neighborhood of 120°E meridian, and is thus named the Meridian Project. It has officially been approved by the Chinese government and will be finished by 2009. This talk will give an overview of the Meridian Project and the proposed International Space Weather Meridian Circle Program.

  4. Project Monitoring and Control Measures In CMMI

    Directory of Open Access Journals (Sweden)

    Mahmoud Khraiwesh

    2013-10-01

    Full Text Available Project monitoring and control process is an important process in developing any computer informationsystem. Monitoring and Control provides an understanding of the project’s progress so that when theproject deviates significantly from the plan appropriate corrective actions can be taken. This research willidentify general measures for the specific goals and its specific practices of Project Monitoring andControl Process Area in Capability Maturity Model Integration (CMMI. CMMI is developed in USA bySoftware Engineering Institute (SEI in Carnegie Mellon University. CMMI is a framework for assessmentand improvement of computer information systems. The procedure we used to determine the measures is toapply the Goal Questions Metrics (GQM approach to the two specific goals and its ten specific practicesof Project Monitoring and Control Process Area in CMMI.

  5. SOUTHERN FINE PARTICULATE MONITORING PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Unknown

    2002-04-01

    This quarterly report presents results and analysis of continuous onsite ambient fine particulate data at the North Birmingham sampling site during the January-March, 2002 study period. The continuous data include PM{sub 2.5} mass concentrations measured by TEOM, particle sulfate using the R&P 8400S monitor, particle size distributions measured by SMPS and APS monitors, and PM{sub 2.5} light scattering extinction coefficient as measured by nephelometer. Some instrumental issues were noted with the upgrade of the APS model 3320 are described in the report, as well as preliminary performance indications for the upgraded instrument. During the quarter preliminary data analysis and modeling studies were conducted to test the potential of the North Birmingham site data for source attribution analyses. Our initial assessment has continued to be optimistic in this regard due to the location of the site relative to several important classes of local and midrange emission sources. We anticipate that these analyses will provide good separations of the effects of major source classes and spatial source clusters, and will provide useful information relevant to PM{sub 2.5} implementation strategies.

  6. Stream restoration and enhancement projects: is anyone monitoring?

    Science.gov (United States)

    Bash, Jeffrey S; Ryan, Clare M

    2002-06-01

    Declines in salmon stocks and general watershed health in Washington State, USA, have led to an increase in stream restoration and enhancement projects initiated throughout the state. The increasing number of projects has also raised questions regarding the monitoring of these efforts. Project managers receiving hydraulic project approvals (HPAs) were surveyed to determine whether monitoring was taking place on their projects. About half the project managers surveyed reported the collection of baseline data and the use of biological, physical, chemical, or other water quality measures for their projects. Of those who reported collection of monitoring data, only 18% indicated that monitoring was required. Respondents were also asked to rank the importance of various project goals on a Likert scale. Project managers with projects focusing on "engineering" goals (e.g., roadbed stabilization) were less likely than other project managers to collect baseline monitoring data. Project managers with projects focusing on "restoration/ecological" or "fisheries" goals were more likely than other project managers to collect monitoring measures. Although monitoring appears to be taking place in slightly more than half of the projects surveyed, the nature of the data collected varies widely across projects, and in most cases the monitoring effort is voluntary. This suggests that project sponsors, funders, and managers must consider the issues involved in requiring appropriate monitoring, establishing standardized monitoring guidelines, the time frames in which to monitor, providing other incentives for conducting monitoring, and ensuring adequate funding for monitoring efforts.

  7. A Web-Based Monitoring System for Multidisciplinary Design Projects

    Science.gov (United States)

    Rogers, James L.; Salas, Andrea O.; Weston, Robert P.

    1998-01-01

    In today's competitive environment, both industry and government agencies are under pressure to reduce the time and cost of multidisciplinary design projects. New tools have been introduced to assist in this process by facilitating the integration of and communication among diverse disciplinary codes. One such tool, a framework for multidisciplinary computational environments, is defined as a hardware and software architecture that enables integration, execution, and communication among diverse disciplinary processes. An examination of current frameworks reveals weaknesses in various areas, such as sequencing, displaying, monitoring, and controlling the design process. The objective of this research is to explore how Web technology, integrated with an existing framework, can improve these areas of weakness. This paper describes a Web-based system that optimizes and controls the execution sequence of design processes; and monitors the project status and results. The three-stage evolution of the system with increasingly complex problems demonstrates the feasibility of this approach.

  8. Railway network design with multiple project stages and time sequencing

    Science.gov (United States)

    Kuby, Michael; Xu, Zhongyi; Xie, Xiaodong

    This paper presents a spatial decision support system for network design problems in which different kinds of projects can be built in stages over time. It was developed by the World Bank and China's Ministry of Railways to plan investment strategies for China's overburdened railway system. We first present a mixed-integer program for the single-period network design problem with project choices such as single or multiple tracks and/or electrification with economies of scale. Then, because such projects can be built all at once or in stages, we developed a heuristic backwards time sequencing procedure with a cost adjustment factor to solve the ``project staging'' problem. Other innovations include a preloading routine; coordinated modeling of arcs, paths, and corridors; and a custom-built GIS.

  9. The study on stage financing model of IT project investment.

    Science.gov (United States)

    Chen, Si-hua; Xu, Sheng-hua; Lee, Changhoon; Xiong, Neal N; He, Wei

    2014-01-01

    Stage financing is the basic operation of venture capital investment. In investment, usually venture capitalists use different strategies to obtain the maximum returns. Due to its advantages to reduce the information asymmetry and agency cost, stage financing is widely used by venture capitalists. Although considerable attentions are devoted to stage financing, very little is known about the risk aversion strategies of IT projects. This paper mainly addresses the problem of risk aversion of venture capital investment in IT projects. Based on the analysis of characteristics of venture capital investment of IT projects, this paper introduces a real option pricing model to measure the value brought by the stage financing strategy and design a risk aversion model for IT projects. Because real option pricing method regards investment activity as contingent decision, it helps to make judgment on the management flexibility of IT projects and then make a more reasonable evaluation about the IT programs. Lastly by being applied to a real case, it further illustrates the effectiveness and feasibility of the model.

  10. Monitored Geologic Repository Project Description Document

    Energy Technology Data Exchange (ETDEWEB)

    P. M. Curry

    2001-01-30

    The primary objective of the Monitored Geologic Repository Project Description Document (PDD) is to allocate the functions, requirements, and assumptions to the systems at Level 5 of the Civilian Radioactive Waste Management System (CRWMS) architecture identified in Section 4. It provides traceability of the requirements to those contained in Section 3 of the ''Monitored Geologic Repository Requirements Document'' (MGR RD) (YMP 2000a) and other higher-level requirements documents. In addition, the PDD allocates design related assumptions to work products of non-design organizations. The document provides Monitored Geologic Repository (MGR) technical requirements in support of design and performance assessment in preparing for the Site Recommendation (SR) and License Application (LA) milestones. The technical requirements documented in the PDD are to be captured in the System Description Documents (SDDs) which address each of the systems at Level 5 of the CRWMS architecture. The design engineers obtain the technical requirements from the SDDs and by reference from the SDDs to the PDD. The design organizations and other organizations will obtain design related assumptions directly from the PDD. These organizations may establish additional assumptions for their individual activities, but such assumptions are not to conflict with the assumptions in the PDD. The PDD will serve as the primary link between the technical requirements captured in the SDDs and the design requirements captured in US Department of Energy (DOE) documents. The approved PDD is placed under Level 3 baseline control by the CRWMS Management and Operating Contractor (M and O) and the following portions of the PDD constitute the Technical Design Baseline for the MGR: the design characteristics listed in Table 1-1, the MGR Architecture (Section 4.1), the Technical Requirements (Section 5), and the Controlled Project Assumptions (Section 6).

  11. A Cryosphere Monitoring Project in the Himalayas

    Science.gov (United States)

    Stumm, D.; Mool, P. K.; Shresta, A. B.; Joshi, S. P.; Bajracharya, S. R.; Kayastha, R. B.; Devkota, L. P.; Bajracharya, O. R.

    2011-12-01

    The Cryosphere Monitoring Project (CMP) has been initiated by ICIMOD (International Centre for Integrated Mountain Development) with the aim to gain more knowledge about the cryosphere in the Himalayas and to build capacities in Nepalese organisations. The CMP is carried out in collaboration with the Kathmandu University, Tribhuvan University, the Department of Hydrology and Meteorology and the Water and Energy Commission Secretariat, and is sponsored by the Royal Norwegian Embassy. The CMP has a multilevel and integrative approach and consists of the following five components: (1) glacier monitoring, (2) assessment of current and future water resources at catchment and sub-basin scale, (3) multi-level remote sensing based observations for glacier and snow monitoring, (4) strengthening ICIMOD as regional knowledge hub for cryospheric information, (5) capacity building of Nepalese organisations. The glacier monitoring component includes field-based mass balance, geometry and glacier flow measurements on two clean and one debris-covered glacier and their analysis, as well as snow cover measurements. The in-situ glacier measurements promote process understanding, provide a refined temporal resolution of mass balance data and data for calibration of glacio-hydrological models. To assess current water resources, meteorological and hydrological measurements are initiated and the run-off is calculated with glacio-hydrological and snow-melt models for the catchments of the selected glaciers. Future water availability will be assessed by down-scaling regional climate model (RCM) data that is applied to the glacio-hydrological model. Remote sensing data is used to improve spatial information about the glacier distribution by refining glacier inventories, and to calculate the geodetic mass balance for the selected glaciers to complement the directly measured glacier mass balance. Additionally, the operation of a MODIS satellite receiving station is planned to obtain near real

  12. Integrated monitoring and surveillance system demonstration project

    Energy Technology Data Exchange (ETDEWEB)

    Aumeier, S.E.; Walters, G. [Argonne National Lab., Idaho Falls, ID (United States); Kotter, D.; Walrath, W.M.; Zamecnik, R.J. [Lockheed-Martin Idaho Technologies Company, Idaho Falls, ID (United States)

    1997-07-01

    We present a summary of efforts associated with the installation of an integrated system for the surveillance and monitoring of stabilized plutonium metals and oxides in long-term storage. The product of this effort will include a Pu storage requirements document, baseline integrated monitoring and surveillance system (IMSS) prototype and test bed that will be installed in the Fuel Manufacturing Facility (FMF) nuclear material vault at Argonne National Laboratory - West (ANL-W), and a Pu tracking database including data analysis capabilities. The prototype will be based on a minimal set of vault and package monitoring requirements as derived from applicable DOE documentation and guidelines, detailed in the requirements document, including DOE-STD-3013-96. The use of standardized requirements will aid individual sites in the selection of sensors that best suit their needs while the prototype IMSS, located at ANL-W, will be used as a test bed to compare and contrast sensor performance against a baseline integrated system (the IMSS), demonstrate system capabilities, evaluate potential technology gaps, and test new hardware and software designs using various storage configurations. With efforts currently underway to repackage and store a substantial quantity of plutonium and plutonium-bearing material within the DOE complex, this is an opportune time to undertake such a project. 4 refs.

  13. Monitored Geologic Repository Project Description Document

    Energy Technology Data Exchange (ETDEWEB)

    P. Curry

    2001-06-26

    The primary objective of the Monitored Geologic Repository Project Description Document (PDD) is to allocate the functions, requirements, and assumptions to the systems at Level 5 of the Civilian Radioactive Waste Management System (CRWMS) architecture identified in Section 4. It provides traceability of the requirements to those contained in Section 3 of the Yucca Mountain Site Characterization Project Requirements Document (YMP RD) (YMP 2001a) and other higher-level requirements documents. In addition, the PDD allocates design related assumptions to work products of non-design organizations. The document provides Monitored Geologic Repository (MGR) technical requirements in support of design and performance assessment in preparing for the Site Recommendation (SR) and License Application (LA) milestones. The technical requirements documented in the PDD are to be captured in the System Description Documents (SDDs) which address each of the systems at Level 5 of the CRWMS architecture. The design engineers obtain the technical requirements from the SDDs and by reference from the SDDs to the PDD. The design organizations and other organizations will obtain design related assumptions directly from the PDD. These organizations may establish additional assumptions for their individual activities, but such assumptions are not to conflict with the assumptions in the PDD. The PDD will serve as the primary link between the technical requirements captured in the SDDs and the design requirements captured in US Department of Energy (DOE) documents. The approved PDD is placed under Level 3 baseline control by the CRWMS Management and Operating Contractor (M&O) and the following portions of the PDD constitute the Technical Design Baseline for the MGR: the design characteristics listed in Table 1-1, the MGR Architecture (Section 4.1), the Technical Requirements (Section 5), and the Controlled Project Assumptions (Section 6).

  14. Three-Dimensional Health Monitoring of Sandwich Composites Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR project delivers a single-chip structural health-monitoring (SHM) system that uses the impedance method to monitor bulk interiors and wave propagation...

  15. Project Design Concept for Monitoring and Control System

    Energy Technology Data Exchange (ETDEWEB)

    MCGREW, D.L.

    2000-10-02

    This Project Design Concept represents operational requirements established for use in design the tank farm Monitoring and Control System. These upgrades are included within the scope of Project W-314, Tank Farm Restoration and Safe Operations.

  16. Ion Mobility Spectrometry for Water Monitoring Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Current water quality monitors aboard the International Space Station (ISS) are specialized and provide limited data. The Colorimetric Water Quality Monitor Kit...

  17. Browns Park National Wildlife Refuge monitoring projects

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This project report summarizes the projects conducted at BPNWR between 2005- 2010. At the end of this report is a list of all of the project deliverables. These...

  18. 28 CFR 512.17 - Monitoring approved research projects.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Monitoring approved research projects. 512.17 Section 512.17 Judicial Administration BUREAU OF PRISONS, DEPARTMENT OF JUSTICE GENERAL MANAGEMENT AND ADMINISTRATION RESEARCH Research § 512.17 Monitoring approved research projects. The...

  19. FY 2002 Integrated Monitoring Plan for the Hanford Groundwater Monitoring Project

    Energy Technology Data Exchange (ETDEWEB)

    Hartman, Mary J.; Dresel, P Evan; Lindberg, Jonathan W.; Newcomer, Darrell R.; Thornton, Edward C.

    2001-10-31

    This document is an integrated monitoring plan for the groundwater project and contains: well and constituent lists for monitoring required by the Atomic Energy Act of 1954 and its implementing orders ("surveillance monitoring"); other, established monitoring plans by reference; and a master well/ constituent/frequency matrix for the entire Hanford Site.

  20. Monitoring in educational development projects : the development of a monitoring system

    NARCIS (Netherlands)

    Plomp, Tjeerd; Huijsman, Hari; Kluyfhout, Eric

    1992-01-01

    Monitoring in education is usually focused on the monitoring of educational systems at different levels. Monitoring of educational projects receives only recently explicit attention. The paper discusses first the concepts of educational monitoring and evaluation. After that, the experience with deve

  1. Tools for Monitoring Social Media: A Marketing Research Project

    Science.gov (United States)

    Veeck, Ann; Hoger, Beth

    2014-01-01

    Knowledge of how to effectively monitor social media is an increasingly valued marketing research skill. This study tests an approach for adding social media content to an undergraduate marketing research class team project. The revised project maintains the expected objectives and parameters of a traditional research project, while integrating…

  2. Tools for Monitoring Social Media: A Marketing Research Project

    Science.gov (United States)

    Veeck, Ann; Hoger, Beth

    2014-01-01

    Knowledge of how to effectively monitor social media is an increasingly valued marketing research skill. This study tests an approach for adding social media content to an undergraduate marketing research class team project. The revised project maintains the expected objectives and parameters of a traditional research project, while integrating…

  3. Two staged incentive contract focused on efficiency and innovation matching in critical chain project management

    Directory of Open Access Journals (Sweden)

    Min Zhang

    2014-09-01

    Full Text Available Purpose: The purpose of this paper is to define the relative optimal incentive contract to effectively encourage employees to improve work efficiency while actively implementing innovative behavior. Design/methodology/approach: This paper analyzes a two staged incentive contract coordinated with efficiency and innovation in Critical Chain Project Management using learning real options, based on principle-agent theory. The situational experiment is used to analyze the validity of the basic model. Finding: The two staged incentive scheme is more suitable for employees to create and implement learning real options, which will throw themselves into innovation process efficiently in Critical Chain Project Management. We prove that the combination of tolerance for early failure and reward for long-term success is effective in motivating innovation. Research limitations/implications: We do not include the individual characteristics of uncertain perception, which might affect the consistency of external validity. The basic model and the experiment design need to improve. Practical Implications: The project managers should pay closer attention to early innovation behavior and monitoring feedback of competition time in the implementation of Critical Chain Project Management. Originality/value: The central contribution of this paper is the theoretical and experimental analysis of incentive schemes for innovation in Critical Chain Project Management using the principal-agent theory, to encourage the completion of CCPM methods as well as imitative free-riding on the creative ideas of other members in the team.

  4. Quality Assurance Project Plan for Facility Effluent Monitoring Plan activities

    Energy Technology Data Exchange (ETDEWEB)

    Frazier, T.P.

    1994-10-20

    This Quality Assurance Project Plan addresses the quality assurance requirements for the activities associated with the Facility Effluent Monitoring Plans, which are part of the overall Hanford Site Environmental Protection Plan. This plan specifically applies to the sampling and analysis activities and continuous monitoring performed for all Facility Effluent Monitoring Plan activities conducted by Westinghouse Hanford Company. It is generic in approach and will be implemented in conjunction with the specific requirements of the individual Facility Effluent Monitoring Plans.

  5. Evolutionary Autonomous Health Monitoring System (EAHMS) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — For supporting NASA's Robotics, Tele-Robotics and Autonomous Systems Roadmap, we are proposing the "Evolutionary Autonomous Health Monitoring System" (EAHMS) for...

  6. Electronic Health Monitoring for Space Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Prognostic monitoring capabilities for space exploration aircrafts are crucial to enable safety and reliability in these platforms. Nokomis proposes to develop and...

  7. Bayesian-based Project Monitoring: Framework Development and Model Testing

    Directory of Open Access Journals (Sweden)

    Budi Hartono

    2015-12-01

    Full Text Available During project implementation, risk becomes an integral part of project monitoring. Therefore. a tool that could dynamically include elements of risk in project progress monitoring is needed. This objective of this study is to develop a general framework that addresses such a concern. The developed framework consists of three interrelated major building blocks, namely: Risk Register (RR, Bayesian Network (BN, and Project Time Networks (PTN for dynamic project monitoring. RR is used to list and to categorize identified project risks. PTN is utilized for modeling the relationship between project activities. BN is used to reflect the interdependence among risk factors and to bridge RR and PTN. A residential development project is chosen as a working example and the result shows that the proposed framework has been successfully applied. The specific model of the development project is also successfully developed and is used to monitor the project progress. It is shown in this study that the proposed BN-based model provides superior performance in terms of forecast accuracy compared to the extant models.

  8. The Research and Implementation of Three Stages Traffic Stations Intelligent Monitor Systems Based on GIS

    Science.gov (United States)

    Hong-ying, Chen; Ting, Xiao; WangTao; Jin-yi, He

    This system used three stage intelligent traffic station subsystems to forecast the path on which vehicle will go. First stage subsystem can forecast road node which adjacented to traffic station. Second stage subsystem was designed for bigger area, for example city, the third stage subsystem was for the larger area between city. Second stage subsystem system used A* based on orientation to calculate shortest path, third stage subsystem calculated critical node of a large area. The system can compose dispersed monitor information, forecast vehicle path, dynamic analysis, hierarchical monitor .It played an important role in ITS.

  9. Visual Intelligent Robot Performance Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop a Visual Intelligent Robot Performance Monitor (VIRPM) that will help crew members maintain situation awareness of robot performance more...

  10. Compact, High Accuracy CO2 Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Small Business Innovative Research Phase II proposal seeks to develop a low cost, robust, highly precise and accurate CO2 monitoring system. This system will...

  11. Differential Photoacoustic Particle Absorption Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop a highly sensitive and compact monitor to measure light absorption from particulate matters. The fundamental of the proposed device is based on...

  12. Three Color Particle Optical Extinction Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to design, build and test a multi-color (red, green, blue) particle optical extinction monitor suitable for use in either land or airborne applications....

  13. Compact, High Accuracy CO2 Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Small Business Innovative Research Phase I proposal seeks to develop a low cost, robust, highly precise and accurate CO2 monitoring system. This system will...

  14. Community air monitoring and Village Green Project

    Science.gov (United States)

    Cost and logistics are practical issues that have historically constrained the number of locations where long-term, active air pollution measurement is possible. In addition, traditional air monitoring approaches are generally conducted by technical experts with limited engageme...

  15. Acoustic Monitoring for Spaceflight Vehicle Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR will develop and demonstrate acoustic sensor technology enabling real-time, remotely performed measuring and monitoring of sound pressure levels and noise...

  16. Dynamic Strain and Crack Monitoring Sensor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The development of condition-based monitoring sensor network systems has the potential to provide an enhanced aircraft safety by real time assessment of the...

  17. Dynamic Strain and Crack Monitoring Sensor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Los Gatos Research proposes to develop a new automated vehicle health monitoring sensor system capable of measuring loads and detecting crack, corrosion, and...

  18. THE STAGE OF COMPLEX SOFTWARE DEVELOPMENT FOR REMOTE PROJECT MANAGEMENT

    Directory of Open Access Journals (Sweden)

    Paraskevov A. V.

    2015-06-01

    Full Text Available The article is devoted to the gradual development of the complex software development for remote project management, the development of the necessary organizational diagrams, decomposition charts, as well as constraints the design stage. A set of methods and techniques of organization of information processes in production systems allows the selection and the use of an information technology solution for the synthesis of knowledge about the work situation; it is the content of the concept of formation of information resource management for system knowledge-intensive production. Management system of information space in manufacturing organizations is formed in a specific environment, which is characterized as an information resource management system – a system of organization of internal and external flows of information, as well as methods and tools for searching, processing and distribution of information in the organization. At the design stage of the systems during the development of large automated, technology, energy, aerospace, information and other complex complexes experiencing the problems associated with less consideration of the properties and laws of functioning of elements, and more - with a choice of the best structure, optimization of interaction of elements, the definition of optimal modes of their functioning, the influence of the external environment, etc. As we increase the complexity of the system this complex system-wide issues play more significant place

  19. Project W-420 Stack Monitoring system upgrades conceptual design report

    Energy Technology Data Exchange (ETDEWEB)

    TUCK, J.A.

    1998-11-06

    This document describes the scope, justification, conceptual design, and performance of Project W-420 stack monitoring system upgrades on six NESHAP-designated, Hanford Tank Farms ventilation exhaust stacks.

  20. South Bay Salt Pond Restoration Project : Phase 1 monitoring plan

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This SBSP Restoration Project Monitoring Plan provides methods to document the effect of restoration on important elements such as mercury uptake, and water and...

  1. Metro Multnomah Wetlands - Multnomah Channel Wetland Restoration Monitoring Project

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Multnomah Channel Wetland Restoration Monitoring Project characterizes wetlands use by juvenile salmonids and other fishes in the Multnomah Channel Marsh Natural...

  2. Skagit IMW - Skagit River Estuary Intensively Monitored Watershed Project

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This study evaluates system-level effects of several estuary restoration projects on juvenile Chinook salmon production in the Skagit River estuary. The monitoring...

  3. Crucial Component Damage Detection, Monitoring and Mitigation Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR project delivers an on-board structural health-monitoring (SHM) system with embedded sensors that sense mechanical impedance deviations to flag incipient...

  4. Composite Structure Monitoring using Direct Write Sensors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This NASA SBIR Phase II project seeks to develop and demonstrate a suite of sensor products to monitor the health of composite structures. Sensors will be made using...

  5. Walnut Creek Watershed Restoration and Water Quality Monitoring Project

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The primary objective of this project is to establish a nonpoint source monitoring program in relation to the watershed habitat restoration and agricultural...

  6. AFSC/ABL: Southeast Coastal Monitoring Project - CTD database

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Southeast Alaska Coastal Monitoring (SECM) project in Alaska was initiated in 1997 by the Auke Bay Laboratory, National Marine Fisheries Service, to study the...

  7. Welcome to the Walnut Creek Nonbreeding Bird Monitoring Project

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This is a summary of the bird monitoring project at Walnut Creek National Wildlife Refuge (Neal Smith National Wildlife Refuge). The refuge is divided into 28...

  8. Quality Assurance Project Plan for Facility Effluent Monitoring Plan activities

    Energy Technology Data Exchange (ETDEWEB)

    Nickels, J.M.

    1991-06-01

    This Quality Assurance Project Plan addresses the quality assurance requirements for the Facility Monitoring Plans of the overall site-wide environmental monitoring plan. This plan specifically applies to the sampling and analysis activities and continuous monitoring performed for all Facility Effluent Monitoring Plan activities conducted by Westinghouse Hanford Company. It is generic in approach and will be implemented in conjunction with the specific requirements of individual Facility Effluent Monitoring Plans. This document is intended to be a basic road map to the Facility Effluent Monitoring Plan documents (i.e., the guidance document for preparing Facility Effluent Monitoring Plans, Facility Effluent Monitoring Plan determinations, management plan, and Facility Effluent Monitoring Plans). The implementing procedures, plans, and instructions are appropriate for the control of effluent monitoring plans requiring compliance with US Department of Energy, US Environmental Protection Agency, state, and local requirements. This Quality Assurance Project Plan contains a matrix of organizational responsibilities, procedural resources from facility or site manuals used in the Facility Effluent Monitoring Plans, and a list of the analytes of interest and analytical methods for each facility preparing a Facility Effluent Monitoring Plan. 44 refs., 1 figs., 2 tabs.

  9. Back Bay Stormwater Monitoring Project Final Report

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The objective of this project was to assess the influx of nutrients and solid material into Back Bay and its tributaries during and immediately following such storm...

  10. Near-facility environmental monitoring quality assurance project plan

    Energy Technology Data Exchange (ETDEWEB)

    McKinney, S.M.

    1997-11-24

    This Quality Assurance Project Plan addresses the quality assurance requirements for the activities associated with the preoperational and near facility environmental monitoring performed by Waste Management Federal Services, Inc., Northwest Operations and supersedes WHC-EP-0538-2. This plan applies to all sampling and monitoring activities performed by waste management Federal Services, Inc., Northwest Operations in implementing facility environmental monitoring at the Hanford Site.

  11. PERMEABLE TREATMENT WALL EFFECTIVENESS MONITORING PROJECT, NEVADA STEWART MINE

    Science.gov (United States)

    This report summarizes the results of Mine Waste Technology Program (MWTP) Activity III, Project 39, Permeable Treatment Wall Effectiveness Monitoring Project, implemented and funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by EPA and the U.S. De...

  12. Monitoring Completed Coastal Projects - Lessons Learned I

    Science.gov (United States)

    1992-06-01

    breakwater at Spud Point Marina, Bodega Harbor, CA was monitored. Lessons learned are: 35. Small transmitted wave heights, even on the order of a few inches...July 1988. Lott, J. W., ’Spud Point Marina Breakwater, California,’ Bodega Bay, Sonoma County, MP CERC-91-5, US Army Engineer Waterways 1991

  13. Healy Clean Coal Project, Healy, Alaska final Environmental Monitoring Plan

    Energy Technology Data Exchange (ETDEWEB)

    1994-06-14

    This Environmental Monitoring Plan (EMP) provides the mechanism to evaluate the integrated coal combustion/emission control system being demonstrated by the Healy Clean Coal Project (HCCP) as part-of the third solicitation of the US Department of Energy (DOE) Clean Coal Technology Demonstration Program (CCT-III). The EMP monitoring is intended to satisfy two objectives: (1) to develop the information base necessary for identification, assessment, and mitigation of potential environmental problems arising from replication of the technology and (2) to identify and quantify project-specific and site-specific environmental impacts predicted in the National Environmental Policy Act (NEPA) documents (Environmental Impact Statement and Record of Decision). The EMP contains a description of the background and history of development of the project technologies and defines the processes that will take place in the combustion and spray dryer absorber systems, including the formation of flash-calcined material (FCM) and its use in sulfur dioxide (SO{sub 2}) removal from the flue gases. It also contains a description of the existing environmental resources of the project area. The EMP includes two types of environmental monitoring that are to be used to demonstrate the technologies of the HCCP: compliance monitoring and supplemental monitoring. Compliance monitoring activities include air emissions, wastewater effluents, and visibility. Monitoring of these resources provide the data necessary to demonstrate that the power plant can operate under the required state and federal statutes, regulations, and permit requirements.

  14. Medication monitoring and drug testing ethics project.

    Science.gov (United States)

    Payne, Richard; Moe, Jeffrey L; Sevier, Catherine Harvey; Sevier, David; Waitzkin, Michael

    2015-01-01

    In 2012, Duke University initiated a research project, funded by an unrestricted research grant from Millennium Laboratories, a drug testing company. The project focused on assessing the frequency and nature of questionable, unethical, and illegal business practices in the clinical drug testing industry and assessing the potential for establishing a business code of ethics. Laboratory leaders, clinicians, industry attorneys, ethicists, and consultants participated in the survey, were interviewed, and attended two face-to-face meetings to discuss a way forward. The study demonstrated broad acknowledgment of variations in the legal and regulatory environment, resulting in inconsistent enforcement of industry practices. Study participants expressed agreement that overtly illegal practices sometimes exist, particularly when laboratory representatives and clinicians discuss reimbursement, extent of testing, and potential business incentives with medical practitioners. Most respondents reported directly observing probable violations involving marketing materials, contracts, or, in the case of some individuals, directly soliciting people with offers of clinical supplies and other "freebies." While many study respondents were skeptical that voluntary standards alone would eliminate questionable business practices, most viewed ethics codes and credentialing as an important first step that could potentially mitigate uneven enforcement, while improving quality of care and facilitating preferred payment options for credentialed parties. Many were willing to participate in future discussions and industry-wide initiatives to improve the environment.

  15. Project management metrics, KPIs, and dashboards a guide to measuring and monitoring project performance

    CERN Document Server

    Kerzner, Harold

    2013-01-01

    Today, with the growth of complex projects, stakeholder involvement in projects, advances in computer technology for dashboard designs, metrics, and key performance indicators for project management have become an important focus. This Second Edition of the bestselling book walks readers through everything from the basics of project management metrics and key performance indicators to establishing targets and using dashboards to monitor performance. The content is aligned with PMI's PMBOK Guide and stresses "value" as the main focal point.

  16. Handbook to guide the measurement and monitoring of project effectiveness and impact

    Energy Technology Data Exchange (ETDEWEB)

    1986-09-15

    This handbook demonstrates the application of a tool for measuring and monitoring the impact of a development project in the Department of Quezaltenango, Guatemala. That project itself presently is a demonstration. It explores the technical feasibility and the commercial possibilities of direct geothermal heat applications to the processing of agricultural produce - with the eventual purpose of expanding agricultural exports from Guatemala. The handbook focuses on an early stage of the geothermal initiative and guides preparations for future impact measurement and monitoring of geothermal projects. Primarily, guidance is for projects in agricultural applications of geothermal heat - and basically in Quezaltenango. But the exercise and the handbook are relevant in broad outline to other, industrial applications projects as well which may be based in other departments and have immediate impact across the whole country. This handbook attempts to prepare geothermal energy planners in Guatemala for that juncture when geothermal projects can be managed by objectives. It promotes and facilitates thinking about defining specific objectives for projects that result from the demonstration at Zunil (in Quezaltenango Department); and it prompts preparations for obtaining baseline measurements and for making rational projections on the achievements of future projects.

  17. The WATCH All-Sky Monitor for the Granat Project

    DEFF Research Database (Denmark)

    Brandt, Søren; Lund, Niels; Rao, A. R.

    1990-01-01

    The Watch X-ray all-sky monitor, which is designed to localize strong X-ray sources and follow their development, is examined, focusing on the addition of four Watch units to the Granat satellite project. The components of the Watch instrument are described and the capabilities and potential...... scientific returns of the Granat project are discussed. The applications of the Watch monitor are given, including the study of time variations of known sources and the detection and localization of new, transient sources....

  18. Project Planning, Implementation and Monitoring Issues, Findings and Recommendations

    Directory of Open Access Journals (Sweden)

    Muhammad Salim Javed

    2012-08-01

    Full Text Available The Higher Education Commission (HEC, Pakistan is one of the prestigious institutions of Government of Pakistan. It sets educational policies for all public and private sector universities of Pakistan. The objective of this study is to find institutional problems and issues of a project planning, implementation and monitoring issues. For this purpose, projects data were collected from Project Directors, HEC personnel's and consultants. Data were collected from 150 public and private sector universities and higher learning institution in the regions of Pakistan (i.e., Khyber Pakhtoon Khwa, Punjab, Sindh, Balochistan and Azad Jamu Kashmir using questionnaires. To provide the data, respondents were given the choice of being interviewed or self-administer the questionnaire and send them back to the researcher. After studying and analyzing the data, main problem and issues in project planning, implementation and monitoring issues were identified. In the view of these responses, rPecommendation had been concluded.

  19. Gb-Sar Interferometry for Structure Monitoring during Infrastructure Projects

    Science.gov (United States)

    Serrano Juan, A.; Vázquez-Suñé, E.; Monserrat, O.; Crosetto, M.; Hoffman, C.; Ledesma, A.; Criollo, R.; Pujades, E.; Velasco, V.; García, A.

    2015-12-01

    Monitoring is a necessary task for infrastructure projects. Ground-based synthetic aperture radar (GB-SAR) has been used in a large variety of displacement measurements. However, it has not yet been applied as a monitoring tool during construction projects. This paper aims to demonstrate that GB-SAR can be very helpful for understanding the mechanisms that control structure deformations and for identifying unexpected events and sensitive areas during construction projects. This could be done in a cost-effective way, which complements the traditional displacement measurements. An experiment was performed in the future railway station of La Sagrera, Barcelona (Spain) to demonstrate the utility of GB-SAR on structure monitoring during construction projects. In this experiment, GB-SAR precisely quantified wall displacements induced by dewatering. Manual data and numerical models have been used to confirm the measurements with a correlation analysis and by comparing measurements and deformation patterns, which have produced similar results. These results validate the use of the GB-SAR technique as a monitoring tool during construction projects.

  20. Project monitor. Final report. [Allegheny County, PA

    Energy Technology Data Exchange (ETDEWEB)

    Hammond, P.Y.; Beck, P.; Doctors, S.I.

    1979-04-27

    Results are reported of a study of consumers' energy attitudes and behavior. Household consumers and small business consumers (both retail and manufacturing) responded to the survey, but only the household results are reported. The study sought to understand energy-related behavior at the level where the various components of energy policy intersect. Attempts are made to attain this goal by determining the extent to which various properties of the individuals and firms are associated with various amounts of conservation. A representative sample of the adult population in Allegheny County, Pennsylvania was interviewed. Part I introduces the measures of household conservation to be used in the survey. Part II analyzes each of the types of energy conservation - general, winterization, heating, cooling, appliance, transportation, and electricity reductions - and relates them to demographic, situation, attitudinal, and perceptual variables in the household sample. Part III deals with the impacts of Project Pacesetter and the United Mine Workers' strike against the coal operators - particularly, the impact of the coal strike on household residents of Allegheny County. Part IV summarizes the findings and uses them for recommendations regarding energy conservation policy. Additional data are presented in 4 appendices. (MCW)

  1. Pros-IT CNR: an Italian prostate cancer monitoring project.

    Science.gov (United States)

    Noale, Marianna; Maggi, Stefania; Artibani, Walter; Bassi, Pier Francesco; Bertoni, Filippo; Bracarda, Sergio; Conti, Giario Natale; Corvò, Renzo; Gacci, Mauro; Graziotti, Pierpaolo; Magrini, Stefano Maria; Maurizi Enrici, Riccardo; Mirone, Vincenzo; Montironi, Rodolfo; Muto, Giovanni; Pecoraro, Stefano; Porreca, Angelo; Ricardi, Umberto; Tubaro, Andrea; Zagonel, Vittorina; Zattoni, Filiberto; Crepaldi, Gaetano

    2017-04-01

    The Pros-IT CNR project aims to monitor a sample of Italian males ≥18 years of age who have been diagnosed in the participating centers with incident prostate cancer, by analyzing their clinical features, treatment protocols and outcome results in relation to quality of life. Pros-IT CNR is an observational, prospective, multicenter study. The National Research Council (CNR), Neuroscience Institute, Aging Branch (Padua) is the promoting center. Ninety-seven Italian centers located throughout Italy were involved. The field study began in September 1, 2014. Subjects eligible were diagnosed with biopsy-verified prostate cancer, naïve. A sample size of 1500 patients was contemplated. A baseline assessment including anamnestic data, clinical history, risk factors, the initial diagnosis, cancer staging information and quality of life (Italian UCLA Prostate Cancer Index; SF-12 Scale) was completed. Six months after the initial diagnosis, a second assessment evaluating the patient's health status, the treatment carried out, and the quality of life will be made. A third assessment, evaluating the treatment follow-up and the quality of life, will be made 12 months after the initial diagnosis. The 4th, 5th, 6th and 7th assessments, similar to the third, will be completed 24, 36, 48 and 60 months after the initial diagnosis, respectively, and will include also a Food Frequency Questionnaire and the Physical Activity Scale for the Elderly. The study will provide information on patients' quality of life and its variations over time in relation to the treatments received for the prostate cancer.

  2. Het Project Monitoring Risicofactoren en Gezondheid Nederland (MORGEN-project). Jaarverslag 1993

    NARCIS (Netherlands)

    Smit HA; Verschuren WMM; Bueno de Mesquita HB; Seidell JC; CCM

    1994-01-01

    The Monitoring Project on Risk Factors for Chronic Diseases (MORGEN-project) is conducted by the National Institute of Public Health and Environmental Protection (RIVM). Its general purpose is to determine the prevalence of risk factors for chronic diseases as well as the prevalence of some specific

  3. 75 FR 8036 - Monitor-Hot Creek Rangeland Project

    Science.gov (United States)

    2010-02-23

    ... comprises approximately 952,234 acres and is located on the Monitor and Hot Creek Mountain Ranges in Eureka, Nye and Lander Counties, Nevada. DATES: Comments concerning the scope of the analysis must be received... Vernon Keller, Project Coordinator, at 1200 Franklin Way, Sparks, Nevada 89431. The telephone number...

  4. Columbia River Channel Improvement Project Rock Removal Blasting: Monitoring Plan

    Energy Technology Data Exchange (ETDEWEB)

    Carlson, Thomas J.; Johnson, Gary E.

    2010-01-29

    This document provides a monitoring plan to evaluate take as outlined in the National Marine Fisheries Service 2002 Biological Opinion for underwater blasting to remove rock from the navigation channel for the Columbia River Channel Improvement Project. The plan was prepared by the Pacific Northwest National Laboratory (PNNL) for the U.S. Army Corps of Engineers (USACE), Portland District.

  5. Het Project Monitoring Risicofactoren en Gezondheid Nederland (MORGEN-project). Jaarverslag 1993

    OpenAIRE

    1994-01-01

    The Monitoring Project on Risk Factors for Chronic Diseases (MORGEN-project) is conducted by the National Institute of Public Health and Environmental Protection (RIVM). Its general purpose is to determine the prevalence of risk factors for chronic diseases as well as the prevalence of some specific chronic conditions in a sample of the general population. In the MORGEN-project, data on the health status and prevalence of risk factors are collected in a random sample of the general population...

  6. TARGET ANALYSIS OF SUZHOU CREEK REHABILITATION PROJECT STAGE II:BASED ON WATER QUALITY MODEL

    Institute of Scientific and Technical Information of China (English)

    LIAO Zhen-liang; XU Zu-xin

    2004-01-01

    The Suzhou Creek is a seriously polluted tidal river in Shanghai. The Suzhou Creek Rehabilitation Project was launched in 1998, and the total investment will surpass 10 billion yuan RMB. It is important to assess the effectiveness of the project and ascertain its targets. In this study, by analyzing the achievements of Suzhou Creek Rehabilitation Project (Stage I) and its remaining problems, the main tasks of the Project Stage II are proposed. These works are wastewater interception, sediment dredging, bidirectional water diversion, and reconstruction of municipal pump stations. The water quality model established with USEPA's WASP is employed to analyze the quantitative targets of the Project Stage II. In the Project Stage II, the water quality of mainstream and tributaries will be improved continuously, the valus of CODCr, BOD5, DO in the mainstream will steadily attain Class IV according to the National Surface Water Quality Standard, and the ecological environment of Suzhou Creek with continuously recover.

  7. Peacekeeper ICBM PBPS (Stage IV) Safing and Demilitarization Project

    Science.gov (United States)

    Douglass, James L.

    2014-01-01

    Topics covered include: Overview of White Sands Test Facility (WSTF) and Capabilities. History of the Peacekeeper Intercontinental Ballistic Missile (ICBM) Program. Introduction to Safing & Demilitarization Project. Requirements for Safing Project. Approach Constellation Program. Need for Qualified Flight Hardware to Support Constellation. Ability to Use Peacekeeper Hardware to Support Constellation. Additional Uses for the Peacekeeper Post-Boost Propulsion System (PBPS) Hardware.

  8. The IASLC Mesothelioma Staging Project: Improving Staging of a Rare Disease Through International Participation.

    Science.gov (United States)

    Pass, Harvey; Giroux, Dorothy; Kennedy, Catherine; Ruffini, Enrico; Cangir, Ayten K; Rice, David; Asamura, Hisao; Waller, David; Edwards, John; Weder, Walter; Hoffmann, Hans; van Meerbeeck, Jan P; Nowak, Anna; Rusch, Valerie W

    2016-12-01

    For nearly 40 years, there was no generally accepted staging system for malignant pleural mesothelioma. In 1994, members of the International Mesothelioma Interest Group, in collaboration with the International Association for the Study of Lung Cancer, proposed a TNM staging system based on analyses of outcomes in retrospective surgical series and small clinical trials. Subsequently accepted by the American Joint Commission on Cancer and the Union for International Cancer Control for the sixth editions of their staging manuals, this system has since been the international staging standard. However, it has significant limitations, particularly with respect to clinical staging and to the categories for lymph node staging. Here we provide an overview of the development of the International Association for the Study of Lung Cancer malignant pleural mesothelioma staging database, which was designed to address these limitations through the development of a large international data set. Analyses of this database, described in papers linked to this overview, are being used to inform revisions in the eighth editions of the American Joint Commission on Cancer and Union for International Cancer Control staging systems.

  9. [Ultrasound in monitoring of the second stage of labour].

    Science.gov (United States)

    Fouché, C J; Simon, E G; Potin, J; Perrotin, F

    2012-11-01

    In the second stage of labor, fetal head rotation and fetal head position are determinant for the management of labor to attempt a vaginal delivery or a cesarean section. However, digital examination is highly subjective. Nowadays, delivery rooms are often equipped with compact and high performance ultrasound systems. The clinical examination can be easily completed by quantified and reproducible methods. Transabdominal ultrasonography is a well-known and efficient way to determine the fetal head position. Nevertheless, ultrasound approach to assess fetal head descent is less widespread. We can use translabial or transperineal way to evaluate fetal head position. We describe precisely two different types of methods: the linear methods (3 different types) and the angles of progression (4 different types of measurement). Among all those methods, the main pelvic landmarks are the symphysis pubis and the fetal skull. The angle of progression appears promising but the assessment was restricted to occipitoanterior fetal position cases. In the coming years, ultrasound will likely play a greater role in the management of labor. Copyright © 2012 Elsevier Masson SAS. All rights reserved.

  10. Understanding Megaproject Success beyond the Project Close-Out Stage

    Directory of Open Access Journals (Sweden)

    Johan Fahri

    2015-08-01

    Full Text Available Project success has always been an important topic in the project management literature. One of the main discussions is concerned with how a project’s success is evaluated and what factors lead to achieving this success. Traditionally project success has been measured at the point where the project outputs are handed over, after the close out phase. Recently, questions have been raised in the literature as to whether we should be evaluating project success beyond the close out phase, to better account for organizational and societal outcomes.  However, not much has been published about how the long term impacts and outcomes are measured. This is of particular concern in megaprojects as they often attract a high level of public attention and political interest, and have both direct and indirect impacts on the community, environment, and national budgets. In this paper the authors review success factors and criteria that are applicable to projects in general and megaprojects in particular. They identify the significance of evaluating outcomes and impact and propose an ex-post project evaluation (EPPE framework for megaprojects.

  11. Management of the Atmosphere Resource Recovery and Environmental Monitoring Project

    Science.gov (United States)

    Roman, Monsi; Perry, Jay; Howard, David

    2013-01-01

    The Advanced Exploration Systems Program's Atmosphere Resource Recovery and Environmental Monitoring (ARREM) project is working to further optimize atmosphere revitalization and environmental monitoring system architectures. This paper discusses project management strategies that tap into skill sets across multiple engineering disciplines, projects, field centers, and industry to achieve the project success. It is the project's objective to contribute to system advances that will enable sustained exploration missions beyond Lower Earth Orbit (LEO) and improve affordability by focusing on the primary goals of achieving high reliability, improving efficiency, and reducing dependence on ground-based logistics resupply. Technology demonstrations are achieved by infusing new technologies and concepts with existing developmental hardware and operating in a controlled environment simulating various crewed habitat scenarios. The ARREM project's strengths include access to a vast array of existing developmental hardware that perform all the vital atmosphere revitalization functions, exceptional test facilities to fully evaluate system performance, and a well-coordinated partnering effort among the NASA field centers and industry partners to provide the innovative expertise necessary to succeed.

  12. Single stage ECR source for the radioactive ion beam project in Louvain- la-Neuve

    Energy Technology Data Exchange (ETDEWEB)

    Arnould, M.; Vanhorenbeeck, J.; Baeten, F.; Dom, C.; Darquennes, D.; Delbar, T.; Jongen, Y.; Huyse, M.; Reusen, G.; Van Duppen, P. and others

    1989-01-01

    In 1987 the project RIB (Radioactive Ion Beam) was started at Louvain-La - Neuve, to produce and accelerate radioactive nuclei of C, N, O, F and Ne. Within the framework of this project, a single stage E.C.R. source will be built. The general scheme of the project and the design of the source are discussed.

  13. Short Mountain Landfill Gas Recovery Project : Stage 1 Environmental Assessment.

    Energy Technology Data Exchange (ETDEWEB)

    United States. Bonneville Power Administration.

    1992-05-01

    The Bonneville Power Administration (BPA), a Federal power marketing agency, has statutory responsibilities to supply electrical power to its utility, industrial, and other customers in the Pacific Northwest. BPA`s latest load/resource balance forecast, projects the capability of existing resources to satisfy projected Federal system loads. The forecast indicates a potential resource deficit. The underlying need for action is to satisfy BPA customers` demand for electrical power.

  14. The IASLC/ITMIG Thymic Epithelial Tumors Staging Project

    DEFF Research Database (Denmark)

    Kondo, Kazuya; Van Schil, Paul; Detterbeck, Frank C

    2014-01-01

    Stage classification is an important underpinning of management of patients with cancer, and rests on a combination of three components: T for tumor extent, N for nodal involvement, and M for more distant metastases. This article details an initiative to develop proposals for the first official...

  15. Water-Level Monitoring Plan for the Hanford Groundwater Monitoring Project

    Energy Technology Data Exchange (ETDEWEB)

    D.R. Newcomer; J.P. McDonald; M.A. Chamness

    1999-09-30

    This document presents the water-level monitoring plan for the Hanford Groundwater Monitoring Project, conducted by the Pacific Northwest National Laboratory (PNNL). Water-level monitoring of the groundwater system beneath the Hanford Site is performed to fulfill the requirements of various state and federal regulations, orders, and agreements. The primary objective of this monitoring is to determine groundwater flow rates and directions. To meet this and other objectives, water-levels are measured annually in monitoring wells completed within the unconfined aquifer system, the upper basalt-confined aquifer system, and in the lower basalt-confined aquifers for surveillance monitoring. At regulated waste units, water levels are taken monthly, quarterly, semi-annually, or annually, depending on the hydrogeologic conditions and regulatory status of a given site. The techniques used to collect water-level data are described in this document along with the factors that affect the quality of the data and the strategies employed by the project to minimize error in the measurement and interpretation of water levels. Well networks are presented for monitoring the unconfined aquifer system, the upper basalt-confined aquifer system, and the lower basalt-confined aquifers, all at a regional scale (surveillance monitoring), as well as the local-scale well networks for each of the regulated waste units studied by this project (regulated-unit monitoring). The criteria used to select wells for water-table monitoring are discussed. It is observed that poor well coverage for surveillance water-table monitoring exists south and west of the 200-West Area, south of the 100-F Area, and east of B Pond and the Treated Effluent Disposal Facility (TEDF). This poor coverage results from a lack of wells suitable for water-table monitoring, and causes uncertainty in representation of the regional water-table in these areas. These deficiencies are regional in scale and apply to regions outside

  16. Process performance indicators in project pre-design stage

    NARCIS (Netherlands)

    Haponava, T.; Al-Jibouri, S.; Reymen, I.

    2006-01-01

    Traditionally performance in construction is measured based on the "iron-triangle”- time, cost and quality. In recent years indicators have been developed to include the measurements of other aspects of project performance. The main shortcoming of these however is that most of them are lagging indic

  17. PENERAPAN SISTEM ERP DALAM MEMBUAT PROJECT FEASIBILITY, PROJECT STATUS DAN PROJECT MONITORING PADA PERUSAHAAN DI BIDANG KONTRAKTOR

    Directory of Open Access Journals (Sweden)

    Hendra Alianto

    2013-11-01

    cost reduction, and improvement of business processes, which will result in an increase in the work (productivity to become more efficient and effective. However, practically some organizations have problems on running ERP system, some even fail. Therefore, a strategy is needed to help the information systems project. Making project feasibility, project status and project monitoring ERP system can be used as a guide in the design of the ERP program applications to become more user-friendly and suitable for the organization needs. The ERP system applied to a contracting company will increase productivity and achieve the level of effectiveness and efficiency of the company's operations. Through strategies in making project feasibility, and status monitoring with ERP system will provide a positive contribution to the development and objectives of the company, so as to improve the effectiveness and efficiency in the processing operations.

  18. Project W-420 Ventilation Stack Monitoring System Year 2000 Compliance Assessment Project Plan

    Energy Technology Data Exchange (ETDEWEB)

    BUSSELL, J.H.

    1999-08-25

    This assessment describes the potential Year 2000 (Y2K) problems and describes the methods for achieving Y2K Compliance for Project W-420, Ventilation Stack Monitoring Systems Upgrades. The purpose of this assessment is to give an overview of the project. This document will not be updated and any dates contained in this document are estimates and may change. The project work scope includes upgrades to ventilation stacks and generic effluent monitoring systems (GEMS) at the 244-A Double Contained Receiver Tank (DCRT), the 244-BX DCRT, the 244-CR Vault, tanks 241-C-105 and 241-C-106, the 244-S DCRT, and the 244-TX DCRT. A detailed description of system dates, functions, interfaces, potential Y2K problems, and date resolutions can not be described since the project is in the definitive design phase, This assessment will describe the methods, protocols, and practices to ensure that equipment and systems do not have Y2K problems.

  19. Biomedical Monitoring By A Novel Noncontact Radio Frequency Technology Project

    Science.gov (United States)

    Oliva-Buisson, Yvette J. (Compiler)

    2014-01-01

    The area of Space Health and Medicine is one of the NASA's Space Technology Grand Challenges. Space is an extreme environment which is not conducive to human life. The extraterrestrial environment can result in the deconditioning of various human physiological systems and thus require easy to use physiological monitoring technologies in order to better monitor space crews for appropriate health management and successful space missions and space operations. Furthermore, the Space Technology Roadmap's Technology Area Breakdown Structure calls for improvements in research to support human health and performance (Technology Area 06). To address these needs, this project investigated a potential noncontact and noninvasive radio frequency-based technique of monitoring central hemodynamic function in human research subjects in response to orthostatic stress.

  20. Fish Research Project Oregon; Umatilla Hatchery Monitoring and Evaluation, 1992 Annual Report.

    Energy Technology Data Exchange (ETDEWEB)

    Keefe, MaryLouise; Carmichael, Richard W.; French, Rod A. (Oregon Department of Fish and Wildlife, Portland, OR)

    1993-03-01

    This report covers the first year of comprehensive monitoring and evaluation of the Umatilla Hatchery. As both the hatchery and the evaluation study are in the early stages of implementation, much of the information contained in this report is preliminary. The most crucial data for evaluating the success of the hatchery program, the data on post-release performance and survival, is yet unavailable. In addition, several years of data are necessary to make conclusions about rearing performance at Umatilla Hatchery. The conclusions drawn in this report should be viewed as preliminary and should be used in conjunction with additional information as it becomes available. A comprehensive fish health monitoring regimen was incorporated into the monitoring and evaluation study for Umatilla Hatchery. This is a unique feature of the Umatilla Hatchery evaluation project.

  1. Hypothermic total body washout and intracranial pressure monitoring in Stage IV Reye syndrome.

    Science.gov (United States)

    Lansky, L L; Kalavsky, S M; Brackett, C E; Wallas, C H; Reis, R L

    1977-04-01

    The number of children in this report treated with either TBW or exchange transfusions is small. Case mortality rates among children with Reye syndrome in Stage IV coma tends to be exceedingly high, varying from 50 to 100%. Intracranial pressure monitoring with the subarachnoid screw may have been an additional factor in increasing our survival data in three patients in the TBW group, since it provided continuous monitoring of ICP and allowed judicious administration of mannitol intravenously. Survival of five of six patients without neurologic sequelae in the present series has encouraged us to coninue utilization of TBW in children with Stage IV Reye syndrome.

  2. Manned Space Flight Project Ready to Start the Second Stage

    Institute of Scientific and Technical Information of China (English)

    LiuJie

    2004-01-01

    China Aerospace Science and Technology Corporation (CASC) made four launches from October 15 to November 15 in 2003, The successful launches made in such short time have proved the ability of the Chinese engineers, technology level and management skills. Especially China's first manned mission achieved a complete success, which indicates that the first step of China's manned space flight project has already been completed and the conditions for the second step is mature.

  3. Meteor Beliefs Project: Shakespeare revisited and the Elizabethan stage's `blazing star'

    Science.gov (United States)

    Gheorghe, Andrei Dorian; McBeath, Alastair

    2007-06-01

    Some fresh Shakespearean citations of meteors, further to those given previously in the Project, are presented, along with a discussion of the Elizabethan stage's use of the `blazing star', with especial reference to the great comet of 1577.

  4. The MAGNUM (Multicolor Active Galactic NUclei Monitoring) Project

    Science.gov (United States)

    Yoshii, Y.; Kobayashi, Y.; Minezaki, T.

    2003-05-01

    The MAGNUM Project is designed to carry out long-term monitoring observations of hundreds of active galactic nuclei in the visible and near-infrared wavelength regions. In order to obtain these observations, we built a new 2m optical-infrared telescope, and located it near the Haleakala summit at a height of 3050m within the area of the University of Hawaii's Haleakala Observatory on the Hawaiian Island of Maui. The Project was funded in 1995 and preliminary observations were started early in 2001. We are working toward the realization of an unmanned, automated observatory which is suitable to relatively simple and stable observations over many years. We present an overview of the Project and its current status.

  5. Integrated monitoring and surveillance system demonstration project: Phase I accomplishments

    Energy Technology Data Exchange (ETDEWEB)

    Aumeier, S.E.; Walters, B.G.; Crawford, D.C. [and others

    1997-01-15

    The authors present the results of the Integrated Monitoring and Surveillance System (IMSS) demonstration project Phase I efforts. The rationale behind IMSS development is reviewed and progress in each of the 5 basic tasks is detailed. Significant results include decisions to use Echelon LonWorks networking protocol and Microsoft Access for the data system needs, a preliminary design for the plutonium canning system glovebox, identification of facilities and materials available for the demonstration, determination of possibly affected facility documentation, and a preliminary list of available sensor technologies. Recently imposed changes in the overall project schedule and scope are also discussed and budgetary requirements for competition of Phase II presented. The results show that the IMSS demonstration project team has met and in many cases exceeded the commitments made for Phase I deliverables.

  6. FINAL REPORT ABOUT STAGE II COLLABORATION PROJECT ON LEPROSY REHABILITATION

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Objective. To undertake the pilot experiments of prevention of disability (POD) in 14 different geographical areas to serve as examples for future development of rehabilitation work in China and in Asia. Methods. According to the principles and national criterion, 27 000 people aflected by leprosy were selected and assessed using disability record forms at beginning and followed up regularly for observing changes of different indica-tors. Results. A total of 197 neuritis cases were detected and treated with prednisolone out of 1 407 new or active cas-es. Self-care training of eyes, hands and feet were conducted for 10 500 disabled people affected by leprosy. Compre-hensive therapy was given to 1 804 cases having complicated ulcers of which 1 055 cases have got their ulcers healed.Out of 706 prostheses, 613 were given to patients with satisfactory results. Surgical treatment was given to 269 cases and 251 have shown good progress. Conclusion. Most of patients have got benefit from the project in function or appearance which is very helpful for their going back to the society and agreed by foreign experts during the final evaluation. The experiences from the pro-ject can be implemented in the whole country.

  7. Monitoring different stages of breast cancer using tumour markers CA 15-3, CEA and TPA

    DEFF Research Database (Denmark)

    Sölétormos, G; Nielsen, D; Schiøler, V

    2004-01-01

    -individual biological variation, and the rate of increase. Patient cohorts were as follows: (A) 90 stage II breast cancer patients who were monitored postoperatively, (B) 204 recurrent breast cancer patients who were monitored during first-line chemotherapy, and (C) 112 patients who were monitored during the time...... period after first-line chemotherapy. The sensitivity for progression was 44% (cohort A), 69% (cohort B), and 68% (cohort C) without any false progression signals. Marker lead-times exceeded 3 months in 20% (cohort A) and 27% (cohort C) of patients. Marker lead-times were 1-6 months among 33...

  8. Evaluating Managerial Styles for System Development Life Cycle Stages to Ensure Software Project Success

    Science.gov (United States)

    Kocherla, Showry

    2012-01-01

    Information technology (IT) projects are considered successful if they are completed on time, within budget, and within scope. Even though, the required tools and methodologies are in place, IT projects continue to fail at a higher rate. Current literature lacks explanation for success within the stages of system development life-cycle (SDLC) such…

  9. Evaluating Managerial Styles for System Development Life Cycle Stages to Ensure Software Project Success

    Science.gov (United States)

    Kocherla, Showry

    2012-01-01

    Information technology (IT) projects are considered successful if they are completed on time, within budget, and within scope. Even though, the required tools and methodologies are in place, IT projects continue to fail at a higher rate. Current literature lacks explanation for success within the stages of system development life-cycle (SDLC) such…

  10. Contractors’ Strategic Approaches to Risk Assessment Techniques at Project Planning Stage

    OpenAIRE

    Ahmad Zaini, Afzan; Endut, Intan Rohani; Takim, Roshana

    2011-01-01

    Abstract — The construction industry is still plagued by poor quality, poor workmanship, poor safety and health environment, and poor practices. The current main problem in the Malaysian Construction Industry is delayed projects under the Ninth Malaysia Plan. The idea of introducing formal risk assessment among Malaysian contractors during the project planning stage is a proactive approach to achieve project objectives. Therefore, this research intends to achieve the following objectives: (1)...

  11. TPS In-Flight Health Monitoring Project Progress Report

    Science.gov (United States)

    Kostyk, Chris; Richards, Lance; Hudston, Larry; Prosser, William

    2007-01-01

    Progress in the development of new thermal protection systems (TPS) is reported. New approaches use embedded lightweight, sensitive, fiber optic strain and temperature sensors within the TPS. Goals of the program are to develop and demonstrate a prototype TPS health monitoring system, develop a thermal-based damage detection algorithm, characterize limits of sensor/system performance, and develop ea methodology transferable to new designs of TPS health monitoring systems. Tasks completed during the project helped establish confidence in understanding of both test setup and the model and validated system/sensor performance in a simple TPS structure. Other progress included complete initial system testing, commencement of the algorithm development effort, generation of a damaged thermal response characteristics database, initial development of a test plan for integration testing of proven FBG sensors in simple TPS structure, and development of partnerships to apply the technology.

  12. International Remote Monitoring Project Embalse Nuclear Power Station, Argentina Embalse Remote Monitoring System

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, Sigfried L.; Glidewell, Donnie D.; Bonino, Anibal; Bosler, Gene; Mercer, David; Maxey, Curt; Vones, Jaromir; Martelle, Guy; Busse, James; Kadner, Steve; White, Mike; Rovere, Luis

    1999-07-21

    The Autoridad Regulatoria Nuclear of Argentina (ARN), the International Atomic Energy Agency (IAEA), ABACC, the US Department of Energy, and the US Support Program POTAS, cooperated in the development of a Remote Monitoring System for nuclear nonproliferation efforts. This system was installed at the Embalse Nuclear Power Station last year to evaluate the feasibility of using radiation sensors in monitoring the transfer of spent fuel from the spent fuel pond to dry storage. The key element in this process is to maintain continuity of knowledge throughout the entire transfer process. This project evaluated the fundamental design and implementation of the Remote Monitoring System in its application to regional and international safeguard efficiency. New technology has been developed to enhance the design of the system to include storage capability on board sensor platforms. This evaluation has led to design enhancements that will assure that no data loss will occur during loss of RF transmission of the sensors.

  13. Plan for Demonstration of Online Monitoring for the Light Water Reactor Sustainability Online Monitoring Project

    Energy Technology Data Exchange (ETDEWEB)

    Magdy S. Tawfik; Vivek Agarwal; Nancy J. Lybeck

    2011-09-01

    Condition based online monitoring technologies and development of diagnostic and prognostic methodologies have drawn tremendous interest in the nuclear industry. It has become important to identify and resolve problems with structures, systems, and components (SSCs) to ensure plant safety, efficiency, and immunity to accidents in the aging fleet of reactors. The Machine Condition Monitoring (MCM) test bed at INL will be used to demonstrate the effectiveness to advancement in online monitoring, sensors, diagnostic and prognostic technologies on a pilot-scale plant that mimics the hydraulics of a nuclear plant. As part of this research project, INL will research available prognostics architectures and their suitability for deployment in a nuclear power plant. In addition, INL will provide recommendation to improve the existing diagnostic and prognostic architectures based on the experimental analysis performed on the MCM test bed.

  14. Monitoring Global Croplands with Coarse Resolution Earth Observations: The Global Agriculture Monitoring (GLAM Project

    Directory of Open Access Journals (Sweden)

    Inbal Becker-Reshef

    2010-06-01

    Full Text Available In recent years there has been a dramatic increase in the demand for timely, comprehensive global agricultural intelligence. Timely information on global crop production is indispensable for combating the growing stress on the world’s crop production and for securing both short-term and long-term stable and reliable supply of food. Global agriculture monitoring systems are critical to providing this kind of intelligence and global earth observations are an essential component of an effective global agricultural monitoring system as they offer timely, objective, global information on croplands distribution, crop development and conditions as the growing season progresses. The Global Agriculture Monitoring Project (GLAM, a joint NASA, USDA, UMD and SDSU initiative, has built a global agricultural monitoring system that provides the USDA Foreign Agricultural Service (FAS with timely, easily accessible, scientifically-validated remotely-sensed data and derived products as well as data analysis tools, for crop-condition monitoring and production assessment. This system is an integral component of the USDA’s FAS Decision Support System (DSS for agriculture. It has significantly improved the FAS crop analysts’ ability to monitor crop conditions, and to quantitatively forecast crop yields through the provision of timely, high-quality global earth observations data in a format customized for FAS alongside a suite of data analysis tools. FAS crop analysts use these satellite data in a ‘convergence of evidence’ approach with meteorological data, field reports, crop models, attaché reports and local reports. The USDA FAS is currently the only operational provider of timely, objective crop production forecasts at the global scale. These forecasts are routinely used by the other US Federal government agencies as well as by commodity trading companies, farmers, relief agencies and foreign governments. This paper discusses the operational components

  15. An overview of the Environmental Monitoring Computer Automation Project

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, S.M.; Lorenz, R.

    1992-01-01

    The Savannah River Site (SRS) was bulk to produce plutonium and tritium for national defense. As a result of site operations, routine and accidental releases of radionuclides have occurred. The effects these releases have on the k>cal population and environment are of concern to the Department of Energy (DOE) and SRS personnel. Each year, approximately 40,000 environmental samples are collected. The quality of the samples, analytical methods and results obtained are important to site personnel. The Environmental Monitoring Computer Automation Project (EMCAP) was developed to better manage scheduling, log-in, tracking, analytical results, and report generation. EMCAP can be viewed as a custom Laboratory Information Management System (LIMS) with the ability to schedule samples, generate reports, and query data. The purpose of this paper is to give an overview of the SRS environmental monitoring program, describe the development of EMCAP software and hardware, discuss the different software modules, show how EMCAP improved the Environmental Monitoring Section program, and examine the future of EMCAP at SRS.

  16. An overview of the Environmental Monitoring Computer Automation Project

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, S.M.; Lorenz, R.

    1992-12-31

    The Savannah River Site (SRS) was bulk to produce plutonium and tritium for national defense. As a result of site operations, routine and accidental releases of radionuclides have occurred. The effects these releases have on the k>cal population and environment are of concern to the Department of Energy (DOE) and SRS personnel. Each year, approximately 40,000 environmental samples are collected. The quality of the samples, analytical methods and results obtained are important to site personnel. The Environmental Monitoring Computer Automation Project (EMCAP) was developed to better manage scheduling, log-in, tracking, analytical results, and report generation. EMCAP can be viewed as a custom Laboratory Information Management System (LIMS) with the ability to schedule samples, generate reports, and query data. The purpose of this paper is to give an overview of the SRS environmental monitoring program, describe the development of EMCAP software and hardware, discuss the different software modules, show how EMCAP improved the Environmental Monitoring Section program, and examine the future of EMCAP at SRS.

  17. Standards for documenting and monitoring bird reintroduction projects

    Science.gov (United States)

    Sutherland, W.J.; Armstrong, D.; Butchart, S.H.M.; Earnhardt, J.M.; Ewen, J.; Jamieson, I.; Jones, C.G.; Lee, R.; Newbery, P.; Nichols, J.D.; Parker, K.A.; Sarrazin, F.; Seddon, P.J.; Shah, N.; Tatayah, V.

    2010-01-01

    It would be much easier to assess the effectiveness of different reintroduction methods, and so improve the success of reintroductions, if there was greater standardization in documentation of the methods and outcomes. We suggest a series of standards for documenting and monitoring the methods and outcomes associated with reintroduction projects for birds. Key suggestions are: documenting the planned release before it occurs, specifying the information required on each release, postrelease monitoring occurring at standard intervals of 1 and 5 years (and 10 for long-lived species), carrying out a population estimate unless impractical, distinguishing restocked and existing individuals when supplementing populations, and documenting the results. We suggest these principles would apply, largely unchanged, to other vertebrate classes. Similar methods could be adopted for invertebrates and plants with appropriate modification. We suggest that organizations publically state whether they will adopt these approaches when undertaking reintroductions. Similar standardization would be beneficial for a wide range of topics in environmental monitoring, ecological studies, and practical conservation. ??2010 Wiley Periodicals, Inc.

  18. A monitoring system based on electric vehicle three-stage wireless charging

    Science.gov (United States)

    Hei, T.; Liu, Z. Z.; Yang, Y.; Hongxing, CHEN; Zhou, B.; Zeng, H.

    2016-08-01

    An monitoring system for three-stage wireless charging was designed. The vehicle terminal contained the core board which was used for battery information collection and charging control and the power measurement and charging control core board was provided at the transmitting terminal which communicated with receiver by Bluetooth. A touch-screen display unit was designed based on MCGS (Monitor and Control Generated System) to simulate charging behavior and to debug the system conveniently. The practical application shown that the system could be stable and reliable, and had a favorable application foreground.

  19. STRATEGY AND PLANNING - PROJECT FOR MONITORING STRICTO SENSU POSTGRADUATE ALUMNI

    Directory of Open Access Journals (Sweden)

    Emerson Antonio Maccari

    2014-07-01

    Full Text Available The Coordination of Improvement of Higher Education Personnel (CAPES has been contributing to the development of post-graduate studies in Brazil, through its system of evaluation. Lately, CAPES signaled the importance of follow the professional performance of the alumni as a way to measure the quality of courses. One difficulty reported by institutions that intend to recognize the trajectory of its graduates is to compile a lot of isolated and outdated data. In order to structure the data collection and to assist educational managers in decision making, we propose the development of a system that enables the evolution of the students and alumni professional career, in order to diagnose the influence of the courses. Based on literature review, this study presents an analysis and makes recommendations about the Monitoring Alumni Project planning. As a result, it is expected that the analysis will serve as a driver for conducting the project, aiming to contribute to the academic reflections, and in practice, contribute to improve educational projects quality.

  20. Condition monitoring of distributed systems using two-stage Bayesian inference data fusion

    Science.gov (United States)

    Jaramillo, Víctor H.; Ottewill, James R.; Dudek, Rafał; Lepiarczyk, Dariusz; Pawlik, Paweł

    2017-03-01

    In industrial practice, condition monitoring is typically applied to critical machinery. A particular piece of machinery may have its own condition monitoring system that allows the health condition of said piece of equipment to be assessed independently of any connected assets. However, industrial machines are typically complex sets of components that continuously interact with one another. In some cases, dynamics resulting from the inception and development of a fault can propagate between individual components. For example, a fault in one component may lead to an increased vibration level in both the faulty component, as well as in connected healthy components. In such cases, a condition monitoring system focusing on a specific element in a connected set of components may either incorrectly indicate a fault, or conversely, a fault might be missed or masked due to the interaction of a piece of equipment with neighboring machines. In such cases, a more holistic condition monitoring approach that can not only account for such interactions, but utilize them to provide a more complete and definitive diagnostic picture of the health of the machinery is highly desirable. In this paper, a Two-Stage Bayesian Inference approach allowing data from separate condition monitoring systems to be combined is presented. Data from distributed condition monitoring systems are combined in two stages, the first data fusion occurring at a local, or component, level, and the second fusion combining data at a global level. Data obtained from an experimental rig consisting of an electric motor, two gearboxes, and a load, operating under a range of different fault conditions is used to illustrate the efficacy of the method at pinpointing the root cause of a problem. The obtained results suggest that the approach is adept at refining the diagnostic information obtained from each of the different machine components monitored, therefore improving the reliability of the health assessment of

  1. The Conception of the Information Management of Innovation Project and the Stages of its Implementation

    Directory of Open Access Journals (Sweden)

    Babinska Solomiia Ya.

    2017-01-01

    Full Text Available The informational support plays an important role in the development and implementation of innovative projects, is a prerequisite for development of its conception. Proceeding from this, the article considers approaches of scientists to components of the life cycle of innovation project, revealing that the most of them would allocate three phases (development, implementation, and completion. In terms of the information support for each of these stages were defined objectives, tasks, managerial decisions (selecting of an innovation object; choosing the economy sector; identifying sources of financing; costing; substantiating expediency as to implementing a project; choosing counter-parties; product pricing; selecting markets; further use of the property objects, information arrays, necessary sources of information, it was considered how the conception of information management of innovation project is being implemented in stages.

  2. Risk management of PPP project in the preparation stage based on Fault Tree Analysis

    Science.gov (United States)

    Xing, Yuanzhi; Guan, Qiuling

    2017-03-01

    The risk management of PPP(Public Private Partnership) project can improve the level of risk control between government departments and private investors, so as to make more beneficial decisions, reduce investment losses and achieve mutual benefit as well. Therefore, this paper takes the PPP project preparation stage venture as the research object to identify and confirm four types of risks. At the same time, fault tree analysis(FTA) is used to evaluate the risk factors that belong to different parts, and quantify the influencing degree of risk impact on the basis of risk identification. In addition, it determines the importance order of risk factors by calculating unit structure importance on PPP project preparation stage. The result shows that accuracy of government decision-making, rationality of private investors funds allocation and instability of market returns are the main factors to generate the shared risk on the project.

  3. 7 CFR 634.50 - Program and project monitoring and evaluation.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 6 2010-01-01 2010-01-01 false Program and project monitoring and evaluation. 634.50... Evaluation § 634.50 Program and project monitoring and evaluation. (a) Comprehensive USDA/EPA joint water... and for general RCWP program management. (2) Monitoring, evaluation, and analysis is a joint...

  4. Development of Distributed Research Center for monitoring and projecting regional climatic and environmental changes: first results

    Science.gov (United States)

    Gordov, Evgeny; Shiklomanov, Alexander; Okladinikov, Igor; Prusevich, Alex; Titov, Alexander

    2016-04-01

    Description and first results of the cooperative project "Development of Distributed Research Center for monitoring and projecting of regional climatic and environmental changes" recently started by SCERT IMCES and ESRC UNH are reported. The project is aimed at development of hardware and software platform prototype of Distributed Research Center (DRC) for monitoring and projecting regional climatic and environmental changes over the areas of mutual interest and demonstration the benefits of such collaboration that complements skills and regional knowledge across the northern extratropics. In the framework of the project, innovative approaches of "cloud" processing and analysis of large geospatial datasets will be developed on the technical platforms of two U.S. and Russian leading institutions involved in research of climate change and its consequences. Anticipated results will create a pathway for development and deployment of thematic international virtual research centers focused on interdisciplinary environmental studies by international research teams. DRC under development will comprise best features and functionality of earlier developed by the cooperating teams' information-computational systems RIMS (http://rims.unh.edu) and CLIMATE(http://climate.scert.ru/), which are widely used in Northern Eurasia environment studies. The project includes several major directions of research (Tasks) listed below. 1. Development of architecture and defining major hardware and software components of DRC for monitoring and projecting of regional environmental changes. 2. Development of an information database and computing software suite for distributed processing and analysis of large geospatial data hosted at ESRC and IMCES SB RAS. 3. Development of geoportal, thematic web client and web services providing international research teams with an access to "cloud" computing resources at DRC; two options will be executed: access through a basic graphical web browser and

  5. Fibre Bragg Grating as a Multi-Stage Structure Health Monitoring Sensor

    DEFF Research Database (Denmark)

    Pereira, Gilmar Ferreira

    2016-01-01

    There is a clear need to implement models and measurement systems through the entire life of the wind turbine blade. In this chapter will be presented some work conducted to implement optical fibres as a multi-stage sensor, capable to measure different structural properties, and link them with all...... involving crack growth and fibre Bragg sensing is described that highlights the response from the fibre optic which will correctly detect the presence and growth of damage. Models to implement these results in a damage detection system for a wind turbine blade can then be developed....... the different life stages and support a better design of the wind turbine blades. The characteristics and functionality of fibre Bragg grating sensors are briefly introduced. Their application as multi-stage structure health monitoring sensors for polymer laminate composite is then described...

  6. Activity monitoring reflects cardiovascular and metabolic variations in COPD patients across GOLD stages II to IV.

    Science.gov (United States)

    Kortianou, E A; Louvaris, Z; Vasilopoulou, M; Nasis, I; Kaltsakas, G; Koulouris, N G; Vogiatzis, I

    2013-12-01

    We investigated whether activity monitoring reliably reflects variations in oxygen transport and utilization during walking in COPD patients. Forty-two patients (14 in each GOLD stage II, III and IV) performed an incremental treadmill protocol to the limit of tolerance. Breath-by-breath gas exchange, central hemodynamic variables and activity monitoring were simultaneously recorded. Physiological variables and accelerometer outputs rose linearly with walking speeds. Strong correlations (r[interquartile range, IQR]) were found between treadmill walking intensity (WI: range 0.8-2.0 ms(-2)) and oxygen consumption (0.95 [IQR 0.87-0.97]), (range 7.6-15.5 ml kg(-1)min(-1)); minute ventilation (0.95 [IQR 0.86-0.98]), (range 20-37 l min(-1)); cardiac output (0.89 [IQR 0.73-0.94]), (range 6.8-11.5 l min(-1)) and arteriovenous oxygen concentration difference (0.84 [IQR 0.76-0.90]), (range 7.7-12.1 ml O2100 ml(-1)). Correlations between WI and gas exchange or central hemodynamic parameters were not different across GOLD stages. In conclusion, central hemodynamic, respiratory and muscle metabolic variations during incremental treadmill exercise are tightly associated to changes in walking intensity as recorded by accelerometry across GOLD stages II to IV. Interestingly, the magnitude of these associations is not different across GOLD stages.

  7. Study on Wireless Network Communication in Stage Hydraulic Monitoring System Based on Internet of Things

    Directory of Open Access Journals (Sweden)

    Yue Dong

    2015-01-01

    Full Text Available A novel stage hydraulic monitoring system based on Internet of Things (IoT is proposed in this paper. Compared with the traditional wired system, the proposed system is a flexible working method and can save the cost. Furthermore, it has the low power consumption, high safety, and large scale network. The real-time pressure and flow data can be collected by using the nodes in ZigBee network. The fault detection and diagnosis process was used in this study, which was facilitated by measuring pressure of flow. When the monitored data exceeds the normal range, some failure may occur in the stage hydraulic system. If any failure occurs in the circuit, the maintainers can be informed immediately, which can greatly improve maintenance efficiency, ensuring the failure to be eliminated in time. Meanwhile, we can take advantage of wireless sensor network (WSN to connect the multiple loops and then monitor the loops by using ZigBee technology, which greatly improves the efficiency of monitoring.

  8. Environmental Monitoring - Lillgrund Offshore Wind Farm. Lillgrund Pilot Project

    Energy Technology Data Exchange (ETDEWEB)

    Davy, Thomas (Vattenfall Vindkraft AB, Stockholm (Sweden))

    2009-02-15

    The purpose of this report is to describe the environmental monitoring measures performed for the Lillgrund Offshore Wind Farm and to summarize the results and conclusions. Construction work started in 2006 and the plant was energized in December 2007. At the time of construction Lillgrund was the third largest wind farm offshore in the world and the first large offshore wind farm in Sweden. The purpose of the environmental monitoring is to ensure that there are no negative impacts on the environment stemming from construction of the Lillgrund wind farm as well as to ensure that the conditions stated by the authorities and the Company's commitments are met. The aim is also to collect more information and knowledge on the possible environmental impact for future offshore wind farm projects. For the Lillgrund project, all monitoring programs were included in one document, Monitoring Program - Lillgrund. It was included as part of the procedures to ensure that the Swedish legal requirements on operators control were followed. The authorities approved the document before construction started. The monitoring measures performed during the construction phase included: - A feedback and monitoring program on dredging and spillage; - A feedback and monitoring program on flora and fauna; - Studies and inspections of the refilling and re-establishment of the sea bottom; - Procedure for operators control. The mean measured sediment spillage, as part of the monitoring program on dredging and spillage, varied between 4.6 - 4.8% depending on dredger used. The maximum value allowed by the conditions is 5%. In general, the calculated values for suspended material were limited and the critical value of 0.01 kg/m3 was exceeded only in minor areas for a very limited time. No corrective actions were required. The deposition of sediment was very low and even at the most effected sites it was only just over 1 mm. The largest dredging volumes were for the foundation work, in total 82

  9. The Monitor project: Searching for occultations in young open clusters

    CERN Document Server

    Aigrain, S; Irwin, J; Hebb, L; Irwin, M; Favata, F; Moraux, E; Pont, F; Aigrain, Suzanne; Hodgkin, Simon; Irwin, Jonathan; Hebb, Leslie; Irwin, Mike; Favata, Fabio; Moraux, Estelle; Pont, Frederic

    2006-01-01

    The Monitor project is a photometric monitoring survey of nine young (1-200Myr) clusters in the solar neighbourhood to search for eclipses by very low mass stars and brown dwarfs and for planetary transits in the light curves of cluster members. It began in the autumn of 2004 and uses several 2 to 4m telescopes worldwide. We aim to calibrate the relation between age, mass, radius and where possible luminosity, from the K-dwarf to the planet regime, in an age range where constraints on evolutionary models are currently very scarce. Any detection of an exoplanet in one of our youngest targets (<=10Myr) would also provide important constraints on planet formation and migration timescales and their relation to proto-planetary disc lifetimes. Finally, we will use the light curves of cluster members to study rotation and flaring in low-mass pre-main sequence stars. The present paper details the motivation, science goals and observing strategy of the survey. We present a method to estimate the sensitivity and num...

  10. Environmental Monitoring - Lillgrund Offshore Wind Farm. Lillgrund Pilot Project

    Energy Technology Data Exchange (ETDEWEB)

    Davy, Thomas (Vattenfall Vindkraft AB, Stockholm (Sweden))

    2009-02-15

    The purpose of this report is to describe the environmental monitoring measures performed for the Lillgrund Offshore Wind Farm and to summarize the results and conclusions. Construction work started in 2006 and the plant was energized in December 2007. At the time of construction Lillgrund was the third largest wind farm offshore in the world and the first large offshore wind farm in Sweden. The purpose of the environmental monitoring is to ensure that there are no negative impacts on the environment stemming from construction of the Lillgrund wind farm as well as to ensure that the conditions stated by the authorities and the Company's commitments are met. The aim is also to collect more information and knowledge on the possible environmental impact for future offshore wind farm projects. For the Lillgrund project, all monitoring programs were included in one document, Monitoring Program - Lillgrund. It was included as part of the procedures to ensure that the Swedish legal requirements on operators control were followed. The authorities approved the document before construction started. The monitoring measures performed during the construction phase included: - A feedback and monitoring program on dredging and spillage; - A feedback and monitoring program on flora and fauna; - Studies and inspections of the refilling and re-establishment of the sea bottom; - Procedure for operators control. The mean measured sediment spillage, as part of the monitoring program on dredging and spillage, varied between 4.6 - 4.8% depending on dredger used. The maximum value allowed by the conditions is 5%. In general, the calculated values for suspended material were limited and the critical value of 0.01 kg/m3 was exceeded only in minor areas for a very limited time. No corrective actions were required. The deposition of sediment was very low and even at the most effected sites it was only just over 1 mm. The largest dredging volumes were for the foundation work, in total 82

  11. Stereo Vision for SPHERES-based Navigation and Monitoring Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Maintenance operations and scientific research on the International Space Station (ISS) require active monitoring. Currently the majority of monitoring and recording...

  12. Biodiversity monitoring in Europe: the EU FP7 EBONE project. European biodiversity observation NEtwork

    CSIR Research Space (South Africa)

    Lück-Vogel, Melanie

    2008-09-01

    Full Text Available submission Presentation Poster presentation A) Title Biodiversity Monitoring in Europe: The EU FP7 EBONE project European Biodiversity Observation NEtwork B) Short title EBONE - European Biodiversity Observation NEtwork C) Author(s) Vogel, M. (1..., South Africa F) Biodiversity Monitoring in Europe: The EU FP7 EBONE project European Biodiversity Observation NEtwork On April 1st, 2008 the EU FP7 project EBONE (http://www.ebone.wur.nl/) was launched. The aim of the project...

  13. National inventory of selected biological monitoring programs. Summary report of current or recently completed projects, 1976

    Energy Technology Data Exchange (ETDEWEB)

    Kemp, H. T.

    1976-10-01

    The Inventory has resulted in establishment of a series of data bases containing biological monitoring information of varying types, namely, directory of investigators, record of projects received from mail questionnaire, detailed description of selected biomonitoring projects, and bibliographic citations supporting the projects received. This report contains detailed descriptions of selected biomonitoring projects organized on a state-by-state basis and with appropriate indices.

  14. A Two-Stage Diagnosis Framework for Wind Turbine Gearbox Condition Monitoring

    Directory of Open Access Journals (Sweden)

    Janet M. Twomey

    2013-01-01

    Full Text Available Advances in high performance sensing technologies enable the development of wind turbine condition monitoring system to diagnose and predict the system-wide effects of failure events. This paper presents a vibration-based two stage fault detection framework for failure diagnosis of rotating components in wind turbines. The proposed framework integrates an analytical defect detection method and a graphical verification method together to ensure the diagnosis efficiency and accuracy. The efficacy of the proposed methodology is demonstrated with a case study with the gearbox condition monitoring Round Robin study dataset provided by the National Renewable Energy Laboratory (NREL. The developed methodology successfully picked five faults out of seven in total with accurate severity levels without producing any false alarm in the blind analysis. The case study results indicated that the developed fault detection framework is effective for analyzing gear and bearing faults in wind turbine drive train system based upon system vibration characteristics.

  15. Study on Wireless Network Communication in Stage Hydraulic Monitoring System Based on Internet of Things

    OpenAIRE

    2015-01-01

    A novel stage hydraulic monitoring system based on Internet of Things (IoT) is proposed in this paper. Compared with the traditional wired system, the proposed system is a flexible working method and can save the cost. Furthermore, it has the low power consumption, high safety, and large scale network. The real-time pressure and flow data can be collected by using the nodes in ZigBee network. The fault detection and diagnosis process was used in this study, which was facilitated by measuring ...

  16. Community air monitoring and the Village Green Project ...

    Science.gov (United States)

    Cost and logistics are practical issues that have historically constrained the number of locations where long-term, active air pollution measurement is possible. In addition, traditional air monitoring approaches are generally conducted by technical experts with limited engagement with community members. EPA’s Village Green Project (VGP) is a prototype technology designed to add value to a community environment – VGP is a park bench equipped with air and meteorological instruments that measure ozone, fine particles, wind, temperature, and humidity at a one-minute time resolution, with the open-source Arduino microprocessor operating as the system controller. The data are streamed wirelessly to a database, passed through automatic diagnostic quality checks, and then made publically available on an engaging website. The station was designed to minimize power use; it consumes an estimated 15W and operates entirely on solar power, is engineered to run for several days with minimal solar radiation, and is capable of automatically shutting down components of the system to conserve power and restarting when power availability increases. Situated outside a public library in Durham, North Carolina, VGP has also been a gathering location for air quality experts to engage with community members. During the time span of June, 2013 through January, 2014, the station collected about 3500 hours of ozone and PM2.5 data, with over 90% up-time operating only on solar po

  17. Monitoring and calibration of the ALICE time projection chamber

    CERN Document Server

    Larsen, Dag Toppe

    The aim of the A Large Ion Collider Experiment (ALICE) experiment at CERN is to study the properties of the Quark–Gluon Plasma (QGP). With energies up to 5.5 A T eV for Pb+Pb collisions, the Large Hadron Collider (LHC) sets a new benchmark for heavy- ion collisions, and opens the door to a so far unexplored energy domain. A closer look at some of the physics topics of ALICE is given in Chapter 1. ALICE consists of several sub-detectors and other sub-systems. The various sub- detectors are designed for exploring different aspects of the particle production of an heavy-ion collision. Chapter 2 gives some insight into the design. The main tracking detector is the Time Projection Chamber (TPC). It has more than half million read-out channels, divided into 216 Read-out Partitions (RPs). Each RP is a separate Front-End Electronics (FEE) entity, as described in Chapter 3. A complex Detector Control System (DCS) is needed for configuration, monitoring and control. The heart of it on the RP side is a small embedded ...

  18. On second order sensitivity for stage-based population projection matrix models.

    Science.gov (United States)

    McCarthy, Dominic; Townley, Stuart; Hodgson, Dave

    2008-08-01

    In this paper we present a simple method for identifying life-history perturbations in population projection matrices that yield an accelerating population growth rate. Accelerating growth means that the dependence of the growth rate on the perturbation is convex. Convexity, when the second sensitivity of the growth rate is positive, is calculated using a new formula derived from the transfer function of the perturbed system. This formula is used to explore the relationship between stasis and growth probabilities from stage-structured population projection matrices.

  19. Inventory of current environmental monitoring projects in the US-Canadian transboundary region

    Energy Technology Data Exchange (ETDEWEB)

    Glantz, C.S.; Ballinger, M.Y.; Chapman, E.G.

    1986-05-01

    This document presents the results of a study commissioned to survey and summarize major environmental monitoring projects in the US-Canadian transboundary region. Projects with field sites located within 400 km (250 mi) of the border and active after 1980 were reviewed. The types of projects included: ambient air-quality monitoring, ambient water-quality monitoring, deposition monitoring, forest/vegetation monitoring and research, soil studies, and ecosystem studies. Ecosystem studies included projects involving the measurement of parameters from more than one monitoring category (e.g., studies that measured both water and soil chemistry). Individual descriptions were formulated for 184 projects meeting the spatial and temporal criteria. Descriptions included the official title for the project, its common abbreviation, program emphasis, monitoring site locations, time period conducted, parameters measured, protocols employed, frequency of sample collection, data storage information, and the principal contact for the project. A summary inventory subdivided according to the six monitoring categories was prepared using a computerized data management system. Information on major centralized data bases in the field of environmental monitoring was also obtained, and summary descriptions were prepared. The inventory and data base descriptions are presented in appendices to this document.

  20. Wearable Beat to Beat Blood Pressure Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A key component of NASA's human exploration programs is a system that monitors the health of the crew during the space missions. The wearable physiological monitor...

  1. Biomedical Monitoring by a Novel Noncontact Radio Frequency Technology Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This technology will be a quantum advance in cardiac monitoring and will be applicable in numerous situations such as for immediate assessment and monitoring of...

  2. Characterization of Electrospray Ionization for Spaceflight Water Monitoring Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Current methods for monitoring the water used on the ISS rely heavily on ground analysis of archival samples. Air monitors presently on board the ISS could be used...

  3. Improvement in RUP Project Management via Service Monitoring: Best Practice of SOA

    CERN Document Server

    Saqib, Sheikh Muhammad; Hussain, Shahid; Ahmad, Bashir; Bano, Arjamand

    2010-01-01

    Management of project planning, monitoring, scheduling, estimation and risk management are critical issues faced by a project manager during development life cycle of software. In RUP, project management is considered as core discipline whose activities are carried in all phases during development of software products. On other side service monitoring is considered as best practice of SOA which leads to availability, auditing, debugging and tracing process. In this paper, authors define a strategy to incorporate the service monitoring of SOA into RUP to improve the artifacts of project management activities. Moreover, the authors define the rules to implement the features of service monitoring, which help the project manager to carry on activities in well define manner. Proposed frame work is implemented on RB (Resuming Bank) application and obtained improved results on PM (Project Management) work.

  4. Information Flow Through Stages of Complex Engineering Design Projects: A Dynamic Network Analysis Approach

    DEFF Research Database (Denmark)

    Parraguez, Pedro; Eppinger, Steven D.; Maier, Anja

    2015-01-01

    information flows between activities in complex engineering design projects; 2) we show how the network of information flows in a large-scale engineering project evolved over time and how network analysis yields several managerial insights; and 3) we provide a useful new representation of the engineering...... design process and thus support theory-building toward the evolution of information flows through systems engineering stages. Implications include guidance on how to analyze and predict information flows as well as better planning of information flows in engineering design projects according......The pattern of information flow through the network of interdependent design activities is thought to be an important determinant of engineering design process results. A previously unexplored aspect of such patterns relates to the temporal dynamics of information transfer between activities...

  5. Effective Monitoring and Control of Outsourced Software Development Projects

    NARCIS (Netherlands)

    Ponisio, Laura; Vruggink, P.

    2011-01-01

    In our study of four outsourcing projects we discover mechanisms to support managerial decision making during software development processes. We report on Customer Office, a framework used in practice that facilitates reasoning about projects by highlighting information paths and making

  6. A Mega-project on Space Weather Monitoring Gets the Green Light

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ A 200-million-yuan ($25 million) mega-project of science research on space weather monitoring, namely the Meridian Space Weather Moni toting Project (Meridian Project for short), proposed by several research institutes and universities in China has been approved recently by the Chinese government.

  7. Adding Shareholder Value through Project Performance Measurement, Monitoring & Control

    NARCIS (Netherlands)

    M.M. Akalu; J.R. Turner (Rodney)

    2002-01-01

    textabstractWe present the various views and methods of measuring and controlling project performance, and factors affecting a project. The review indicates that there is a shift in the type and understanding of factors of project success or failure. However, the presence of various measurement meth

  8. Rock stress measurements. Preparatory stage of the equipment development project; Kallioperaen jaennitystilan mittaaminen. Laitekehityshankkeen valmisteluvaihe

    Energy Technology Data Exchange (ETDEWEB)

    Mononen, S.; Hakala, M.; Mikkola, P

    2002-07-01

    In recent years the rock stress measurement methods used in Finland have been overcoring and hydraulic fracturing. There have been mainly two companies involved in these measurements, namely Suomen Malmi Oy (Smoy) and SwedPower AB. Smoy has done measurements for mines and for rock engineering projects, whereas SwedPower AB has mainly been involved in nuclear waste disposal investigations and conducted hydraulic fracturing measurements in deep boreholes. Smoy together with its partners started in February 2001 a project named JTM, which was a preliminary stage for a future project, which aims to develop a device most suitable for rock stress measurements in Finland. The partners in the project were HUT Rock Engineering, Posiva Oy, Saanio and Riekkola Oy, Gridpoint Finland Oy and Geopros Oy. Tekes, the National Technology Agency, provided almost half of the project funding. In the management group of the project were Pekka Mikkola (chairman) and Tero Laurila from Smoy, Pekka Saerkkae and Sakari Mononen (full-time researcher) from HUT, Aimo Hautojaervi (Posiva Oy), Erik Johansson (Saanio and Riekkola Oy), Matti Hakala (Gridpoint Finland Oy) and Heikki Haemaelaeinen (Geopros Oy). The aim of the JTM-project was to find out the needs for the development of a device most suitable for rock stress measurements in Finnish mines and rock engineering projects. During the project work was done to find out the range of rock stress measurement devices available, to find out the needs for measurements, and to get acquainted to the measurements done in Scandinavia. Also a report of the most suitable methods for Finnish rock conditions was done based on literature and on interviews of rock stress experts. Based on all the information collected during the project a clear picture of the needs for rock stress measurements in Finland could be formed and a preliminary plan of a future project was done. The aim of the suggested project is to build a device based on hydraulic fracturing

  9. A Corrosion Sensor for Monitoring the Early-Stage Environmental Corrosion of A36 Carbon Steel

    Directory of Open Access Journals (Sweden)

    Dong Chen

    2014-08-01

    Full Text Available An innovative prototype sensor containing A36 carbon steel as a capacitor was explored to monitor early-stage corrosion. The sensor detected the changes of the surface- rather than the bulk- property and morphology of A36 during corrosion. Thus it was more sensitive than the conventional electrical resistance corrosion sensors. After being soaked in an aerated 0.2 M NaCl solution, the sensor’s normalized electrical resistance (R/R0 decreased continuously from 1.0 to 0.74 with the extent of corrosion. Meanwhile, the sensor’s normalized capacitance (C/C0 increased continuously from 1.0 to 1.46. X-ray diffraction result indicates that the iron rust on A36 had crystals of lepidocrocite and magnetite.

  10. NDE and Stress Monitoring on Composite Overwrapped Pressure Vessels Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Damage caused by composite overwrapped pressure vessels (COPVs) failure can be catastrophic. Thus, monitoring condition and stress in the composite overwrap,...

  11. Compact Monitor for Airborne Carbon Dioxide Measurements Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Eltron Research & Development proposes the development of a lightweight, battery-powered instrument for accurately and rapidly monitoring the local concentration...

  12. A Citizen Science Program for Monitoring Lake Stages in Northern Wisconsin

    Science.gov (United States)

    Kretschmann, A.; Drum, A.; Rubsam, J.; Watras, C. J.; Cellar-Rossler, A.

    2011-12-01

    Historical data indicate that surface water levels in northern Wisconsin are fluctuating more now than they did in the recent past. In the northern highland lake district of Vilas County, Wisconsin, concern about record low lake levels in 2008 spurred local citizens and lake associations to form a lake level monitoring network comprising citizen scientists. The network is administered by the North Lakeland Discovery Center (NLDC, a local NGO) and is supported by a grant from the Citizen Science Monitoring Program of the Wisconsin Department of Natural Resources (WDNR). With technical guidance from limnologists at neighboring UW-Madison Trout Lake Research Station, citizen scientists have installed geographic benchmarks and staff gauges on 26 area lakes. The project engages citizen and student science participants including homeowners, non-profit organization member-participants, and local schools. Each spring, staff gauges are installed and referenced to fixed benchmarks after ice off by NLDC and dedicated volunteers. Volunteers read and record staff gauges on a weekly basis during the ice-free season; and maintain log books recording lake levels to the nearest 0.5 cm. At the end of the season, before ice on, gauges are removed and log books are collected by the NLDC coordinator. Data is compiled and submitted to a database management system, coordinated within the Wisconsin Surface Water Integrated Monitoring System (SWIMS), a statewide information system managed by the WDNR in Madison. Furthermore, NLDC is collaborating with the SWIMS database manager to develop data entry screens based on records collected by citizen scientists. This program is the first of its kind in Wisconsin to utilize citizen scientists to collect lake level data. The retention rate for volunteers has been 100% over the three years since inception, and the program has expanded from four lakes in 2008 to twenty-six lakes in 2011. NLDC stresses the importance of long-term monitoring and the

  13. Developing an Integrated Monitoring and Evaluation Flow for Sustainable Investment Projects

    Directory of Open Access Journals (Sweden)

    Florin TACHE

    2011-12-01

    Full Text Available Under the circumstances of certain weaknesses in the monitoring and evaluation processes of sustainable investment projects, the paper aims to develop a general integrated flow, encompassing both a project monitoring system and also a project evaluation system for the investment projects involving economic objectives, as well as cross-cutting social and environmental targets. The whole approach is being presented as a flowchart, which highlights the intimate relationship between the monitoring and evaluation processes, and provides a formal framework for performing a logical monitoring and evaluation process, taking into account simultaneously the economic, social and environmental perspectives, within an investment project. Last, but not least, the article states both the estimated advantages and the disadvantages of such a managerial tool, opening new perspectives for developing further improved models and systems.

  14. Monitoring stage fright outside the laboratory: an example in a professional musician using wearable sensors.

    Science.gov (United States)

    Kusserow, Martin; Candia, Victor; Amft, Oliver; Hildebrandt, Horst; Folkers, Gerd; Tröster, Gerhard

    2012-03-01

    We implemented and tested a wearable sensor system to measure patterns of stress responses in a professional musician under public performance conditions. Using this sensor system, we monitored the cellist's heart activity, the motion of multiple body parts, and their gradual changes during three repeated performances of a skill-demanding piece in front of a professional audience. From the cellist and her teachers, we collected stage fright self-reports and performance ratings that were related to our sensor data analysis results. Concomitant to changes in body motion and heart rate, the cellist perceived a reduction in stage fright. Performance quality was objectively improved, as technical playing errors decreased throughout repeated renditions. In particular, from performance 1 to 3, the wearable sensors measured a significant increase in the cellist's bowing motion dynamics of approximately 6% and a decrease in heart rate. Bowing motion showed a marginal correlation to the observed heart rate patterns during playing. The wearable system did not interfere with the cellist's performance, thereby allowing investigation of stress responses during natural public performances.

  15. Explanation of the project - The Rice Growth Monitoring for The Phenotypic Functional Analysis | LSDB Archive [Life Science Database Archive metadata

    Lifescience Database Archive (English)

    Full Text Available The Rice Growth Monitoring for The Phenotypic Functional Analysis Explanation of the project Data detail Dat...tion of the project - The Rice Growth Monitoring for The Phenotypic Functional Analysis | LSDB Archive ...

  16. Composite Overwrapped Pressure Vessels (COPV) Monitoring System Using Fiber Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Intelligent Fiber Optic Systems Corporation (IFOS) proposes, in this Phase 1 SBIR project, to demonstrate the feasibility of innovations based on an...

  17. Multi-stage IT project evaluation: The flexibility value obtained by implementing and resolving Berk, Green and Naik (2004) model

    Science.gov (United States)

    Abid, Fathi; Guermazi, Dorra

    2009-11-01

    In this paper, we evaluate a multi-stage information technology investment project, by implementing and resolving Berk, Green and Naik's (2004) model, which takes into account specific features of IT projects and considers the real option to suspend investment at each stage. We present a particular case of the model where the project value is the solution of an optimal control problem with a single state variable. In this case, the model is more intuitive and tractable. The case study confirms the practical potential of the model and highlights the importance of the real-option approach compared to classical discounted cash flow techniques in the valuation of IT projects.

  18. High Performance Fiber-Optic Sensor for Environmental Monitoring Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Los Gatos Research (LGR) proposes to develop a low-cost, compact, lightweight, rugged and easy-to-use environmental monitoring optical fiber sensor device based on...

  19. Aircraft Control Augmentation and Health Monitoring Using FADS Technology Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Phase I research proposal is aimed at demonstrating the feasibility of an innovative architecture comprising control augmentation and on-line health monitoring...

  20. Distributed Rocket Engine Testing Health Monitoring System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Leveraging the Phase I achievements of the Distributed Rocket Engine Testing Health Monitoring System (DiRETHMS) including its software toolsets and system building...

  1. Community air monitoring and the Village Green Project

    Science.gov (United States)

    Cost and logistics are practical issues that have historically constrained the number of locations where long-term, active air pollution measurement is possible. In addition, traditional air monitoring approaches are generally conducted by technical experts with limited engageme...

  2. Improved Combustion Products Monitor for the ISS Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Compound Specific Analyzer – Combustion Products, used on the International Space Station as a warning monitor of smoldering or combustion events, is being...

  3. Distributed Rocket Engine Testing Health Monitoring System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The on-ground and Distributed Rocket Engine Testing Health Monitoring System (DiRETHMS) provides a system architecture and software tools for performing diagnostics...

  4. Non-linear Ultrasonic Bond-Strength Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — To date, bond strength is considered one of the ?holy grails? for NDE. Preliminary data indicates that the Luna Nonlinear Ultrasonic Bond Strength (NUBS) monitor...

  5. Novel Real-Time Flight Envelope Monitoring System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed innovation is an aircraft flight envelope monitoring system that will provide real-time in-cockpit estimations of aircraft flight envelope boundaries,...

  6. Community air monitoring and the Village Green Project

    Science.gov (United States)

    Abstract: Cost and logistics are practical issues that have historically constrained the number of locations where long-term, active air pollution measurement is possible. In addition, traditional air monitoring approaches are generally conducted by technical experts with limite...

  7. Novel Real-Time Flight Envelope Monitoring System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed innovation is an aircraft flight envelope monitoring system that will provide real-time in-cockpit estimations of aircraft flight envelope boundaries....

  8. Improved Combustion Products Monitor for the ISS Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Compound Specific Analyzer - Combustion Products is used on the International Space Station as a warning monitor of smoldering or combustion events and, after...

  9. Multi-Modal Neurodiagnostic Tool for Stress Monitoring Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA has a requirement for a neurodiagnostic tool that can be used to monitor the behavioral health of the crew during long duration Exploration missions. The device...

  10. Water chemistry - Thornton Creek Restoration Project Effectiveness Monitoring

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA has designed and is currently implementing a hyporheic monitoring plan for the Thornton Creek watershed in North Seattle. This work is being conducted for...

  11. Micro GC's for Contaminant Monitoring in Spacecraft Air Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this proposal is to create new gas chromatographs (GCs) for contaminant monitoring in spacecraft air that do not require any reagents or special...

  12. Wearable Beat to Beat Blood Pressure Monitor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A key component of NASA's human exploration programs is a system that monitors the health of the crew during space missions. The wearable beat-to-beat blood pressure...

  13. Aquatic Invertebrates - Thornton Creek Restoration Project Effectiveness Monitoring

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA has designed and is currently implementing a hyporheic monitoring plan for the Thornton Creek watershed in North Seattle. This work is being conducted for...

  14. Novel Non-Intrusive Vibration Monitoring System for Turbopumps Project

    Data.gov (United States)

    National Aeronautics and Space Administration — ASRI proposes to develop an advanced and commercially viable Non-Intrusive Vibration Monitoring System (NI-VMS) which can provide effective on-line/off-line engine...

  15. In-Situ Monitoring of Immune Function Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Monitoring the health and wellness of mission pilots is a critically important function. Space flight has an adverse effect on the human immune response. During...

  16. Passive Wireless Sensor System for Structural Health Monitoring Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Albido proposes to develop a Passive Wireless Sensor System for Structural Health Monitoring capable of measuring high-bandwidth temperature and strain of space and...

  17. High-Performance Contaminant Monitor for Spacecraft Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Vision for Space Exploration demands increasing reliance on real-time trace gas monitors onboard spacecraft. Present grab samples and badges will be inadequate...

  18. On-Orbit Health Monitoring and Repair Assessment of Thermal Protection Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR project delivers On-orbit health MoNItoring and repair assessment of THERMal protection systems (OMNI_THERM). OMNI_THERM features impedance-based...

  19. Autonomus I&C Maintenance and Health Monitoring System for Fission Surface Power Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The primary goal of this project is to design and develop an autonomous instrumentation and control (I&C) health monitoring system for space nuclear power...

  20. Data Analysis Algorithm Suitable for Structural Health Monitoring Based on Dust Network Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposed project will attempt to develop a data analysis system for structural health monitoring on space structures. The data analysis software will be a key...

  1. Wireless Health Monitoring for Large Arrays of MEMS Sensors and Actuators Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this Phase I project is to demonstrate an automated on-line structural health monitoring system for aircraft structures using a combination of...

  2. Prime Hook NWR Marsh Restoration Project Summary & Monitoring Plan 2015

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This living document provides a condensed explanation of wetland management history and a large-scale tidal marsh restoration project at Prime Hook NWR in Delaware....

  3. LCREP growth rates - Lower Columbia River Ecosystem Monitoring Project

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — 1) The purpose of this project is to document juvenile salmon habitat occurrence in the Lower Columbia River and estuary, and examine how habitat conditions...

  4. LCREP chemistry and lipids - Lower Columbia River Ecosystem Monitoring Project

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — 1) The purpose of this project is to document juvenile salmon habitat occurrence in the Lower Columbia River and estuary, and examine how habitat conditions...

  5. LCREP catch records - Lower Columbia River Ecosystem Monitoring Project

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — 1) The purpose of this project is to document juvenile salmon habitat occurrence in the Lower Columbia River and estuary, and examine how habitat conditions...

  6. LCREP genetic stock ID - Lower Columbia River Ecosystem Monitoring Project

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — 1) The purpose of this project is to document juvenile salmon habitat occurrence in the Lower Columbia River and estuary, and examine how habitat conditions...

  7. LCREP prey data - Lower Columbia River Ecosystem Monitoring Project

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — 1) The purpose of this project is to document juvenile salmon habitat occurrence in the Lower Columbia River and estuary, and examine how habitat conditions...

  8. 7 CFR 3405.19 - Monitoring progress of funded projects.

    Science.gov (United States)

    2010-01-01

    ... RESEARCH, EDUCATION, AND EXTENSION SERVICE, DEPARTMENT OF AGRICULTURE HIGHER EDUCATION CHALLENGE GRANTS... Annual Performance Reports should include a summary of the overall progress toward project objectives... reform, and opportunities to enhance dissemination of exemplary end products/results. (b) An...

  9. 7 CFR 3406.26 - Monitoring progress of funded projects.

    Science.gov (United States)

    2010-01-01

    ... award. These reports are in addition to the annual Current Research Information System (CRIS) reports... RESEARCH, EDUCATION, AND EXTENSION SERVICE, DEPARTMENT OF AGRICULTURE 1890 INSTITUTION CAPACITY BUILDING... Annual Performance Reports should include a summary of the overall progress toward project...

  10. In-Process Monitoring of Additive Manufacturing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The key innovation in this project is the implementation of an Imaging Fourier Transform Spectrometer (IFTS) for in situ metal additive manufacturing process...

  11. ICESat Observations of Inland Surface Water Stage, Slope, and Extent: a New Method for Hydrologic Monitoring

    Science.gov (United States)

    Harding, David J.; Jasinski, Michael F.

    2004-01-01

    River discharge and changes in lake, reservoir and wetland water storage are critical terms in the global surface water balance, yet they are poorly observed globally and the prospects for adequate observations from in-situ networks are poor (Alsdorf et al., 2003). The NASA-sponsored Surface Water Working Group has established a framework for advancing satellite observations of river discharge and water storage changes which focuses on obtaining measurements of water surface height (stage), slope, and extent. Satellite laser altimetry, which can achieve centimeter-level elevation precision for single, small laser footprints, provides a method to obtain these inland water parameters and contribute to global water balance monitoring. Since its launch in January, 2003 the Ice, Cloud, and land Elevation Satellite (ICESat), a NASA Earth Observing System mission, has achieved over 540 million laser pulse observations of ice sheet, ocean surface, land topography, and inland water elevations and cloud and aerosol height distributions. By recording the laser backscatter from 80 m diameter footprints spaced 175 m along track, ICESat acquires globally-distributed elevation profiles, using a 1064 nm laser altimeter channel, and cloud and aerosol profiles, using a 532 nm atmospheric lidar channel. The ICESat mission has demonstrated the following laser altimeter capabilities relevant to observations of inland water: (1) elevation measurements with a precision of 2 to 3 cm for flat surfaces, suitable for detecting river surface slopes along long river reaches or between multiple crossings of a meandering river channel, (2) from the laser backscatter waveform, detection of water surface elevations beneath vegetation canopies, suitable for measuring water stage in flooded forests, (3) single pulse absolute elevation accuracy of about 50 cm (1 sigma) for 1 degree sloped surfaces, with calibration work in progress indicating that a final accuracy of about 12 cm (1 sigma) will be

  12. Quality assurance project plan for ground water monitoring activities managed by Westinghouse Hanford Company. Revision 3

    Energy Technology Data Exchange (ETDEWEB)

    Stauffer, M.

    1995-11-01

    This quality assurance project plan (QAPP) applies specifically to the field activities and laboratory analysis performed for all RCRA groundwater projects conducted by Hanford Technical Services. This QAPP is generic in approach and shall be implemented in conjunction with the specific requirements of individual groundwater monitoring plans.

  13. REDD+ readiness: early insights on monitoring, reporting and verification systems of project developers

    NARCIS (Netherlands)

    Joseph, S.; Herold, M.; Sunderlin, W.D.; Verchot, L.V.

    2013-01-01

    A functional measuring, monitoring, reporting and verification (MRV) system is essential to assess the additionality and impact on forest carbon in REDD+ (reducing emissions from deforestation and degradation) projects. This study assesses the MRV capacity and readiness of project developers at 20 R

  14. Manual on SFR R and D and Technology Monitoring System Based on Enterprise Project Management Solution

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dong Uk; Lee, Yong Bum; Won, Byung Chool; Kim, Young In; Hahn, Do Hee

    2008-04-15

    This report is a manual on enterprise project management solution for R and D and technology monitoring system that is applicable for managing the generation IV sodium-cooled fast reactor development. The prime goal of this system is to provide project manager with reliable and accurate information of status of progress, performance and resource allocation, and attain traceability and visibility of project implementation for effective project management. This report is composed of the three part. The first part is an introduction on microsoft project professional software that was used to monitor the progress, evaluate the results and analyze the resource distribution of the activities. The second makes a description of project plan and control, and the third part describes on collaboration and teamwork.

  15. First stage of INTRAMAP: INtegrated Transantarctic Mountains and Ross Sea Area Magnetic Anomaly Project

    Directory of Open Access Journals (Sweden)

    D. Damaske

    1999-06-01

    Full Text Available INTRAMAP (INtegrated Transantarctic Mountains and Ross Sea Area Magnetic Anomaly Project is an international effort to merge the magnetic data acquired throughout the "Ross Sea Antarctic Sector" (south of 60°S between 135°-255°E including the Transantarctic Mountains (TAM, the Ross Sea, Marie Byrd Land, and the Pacific coast, and also to begin the compilation efforts for new data over the Wilkes Basin. This project is a component of the continental scale Antarctic Digital Magnetic Anomaly Project (ADMAP. The first stage of INTRAMAP addresses the analysis and merging of GITARA (1991-1994 and GANOVEX (1984 aeromagnetic surveys together with ground magnetic data (1984-1989. The combined data sets cover an area of approximately 30 km2 over Victoria Land and adjacent Ross Sea. Map and profile gridding were implemented to integrate the data sets. These approaches are studied for improving existing strategies to adopt for the whole magnetic compilation effort. The final microlevelled grid that we produce is a new tool for regional interpretation of the main tectonic and geologic features of this sector of Antarctica.

  16. The GRENE-TEA Model Intercomparison Project (GTMIP: overview and experiment protocol for Stage 1

    Directory of Open Access Journals (Sweden)

    S. Miyazaki

    2015-04-01

    Full Text Available As part of the terrestrial branch of the Japan-funded Arctic Climate Change Research Project (GRENE-TEA, which aims to clarify the role and function of the Arctic terrestrial system in the climate system, and assess the influence of its changes on a global scale, this model intercomparison project (GTMIP is planned and being conducted to (1 enhance communication and understanding between the "minds and hands" (i.e., between the modelling and field scientists and (2 assess the uncertainty and variations stemming from variability in model implementation/design and in model outputs due to climatic and historical conditions in the Arctic terrestrial regions. This paper provides an overview and the experiment protocol of Stage 1 of the project, site simulations driven by statistically fitted data created using the GRENE-TEA site observations for the last three decades. The target metrics for the model evaluation cover key processes in both physics and biogeochemistry, including energy budgets, snow, permafrost, phenology, and carbon budgets. The preliminary results on four metrics (annual mean latent heat flux, annual maximum snow depth, gross primary production, and net ecosystem production already demonstrate the range of variations in reproducibility among existing models and sites. Full analysis on annual as well as seasonal time scales, to be conducted upon completion of model outputs submission, will delineate inter-dependence among the key processes, and provide the clue for improving the model performance.

  17. Remote instrumentation and safeguards monitoring for the star project

    Energy Technology Data Exchange (ETDEWEB)

    Buettner, H M; Labiak, W; Spiridon, A

    2000-06-15

    A part of the Nuclear Energy Research Initiative (NERI) is the development of the Small Transportable Autonomous Reactor (STAR) for deployment in countries that do not have a nuclear industry. STARs would have an output of from 100 to 150 MW electric, would be fueled in the country of manufacture, and after 15 to 20 years of operation the reactor core would be returned to the country of manufacture for refueling. A candidate STAR design can be found in (Greenspan, 2000). This paper describes the design of the control and monitoring system that might be used. There are two unique features to this system. One is that the monitored information will be transmitted to a remote site for two purposes, safeguards, and allowing experts a great distance away direct access to view the reactor's operating parameters. The second feature is safeguards sensors will be designed into the system and there will monitoring of the safeguards aspects of the system for tampering. Any safeguards anomalies will be sent to the remote site as alarms. Encrypted satellite communications will be used to transmit the data. These features allow the STAR to be operated by a small staff and will reduce the costs of safeguards monitoring by reducing the number of plant visits by inspectors.

  18. Nova Scotia S-2000 monitoring project. Vol. 1, Performance summary

    Energy Technology Data Exchange (ETDEWEB)

    Makuch, P.; Harrison, S.J. [Queen`s Univ., Kingston, ON (Canada). Solar Calorimetry Lab.

    1994-12-01

    Electric utility companies have increasingly been evaluating and implementing demand management and conservation. As a result there has been growing interest in potential energy savings and capacity benefits of Solar Domestic Hot Water (SDHW) technologies. A computer simulation study showed that SDHW can provide significant savings in hot water heating. Natural Resources Canada through the Canada Centre for Mineral and Energy Technology (CANMET) initiated the S-2000 program. The S-2000 program was initiated to promote cooperation between CANMET, electric utilities and provincial governments interested in determining whether SDHW systems can reduce peak energy demand and pollution emissions. 60 SDHW systems were installed in Nova Scotia. Systems were monitored by Thermo Dynamics Limited and analyzed by the Solar Calorimetry Laboratory at Queen`s University. Results were produced for the monitoring period from October 1993 to August 1994. Results for 32 of the Nova Scotia systems showed winter and summer solar energy supplies of 14.8 MWh and 30 MWh respectively. The system efficiency was determined to be 28.4%. The system performance was consistent with predictions made from computer simulations, with the exception of an unexpectedly severe winter. The solar energy contribution during the winter was lower than that predicted for typical weather conditions. Of the systems monitored daily average hot water use was lower than the reference 239 L/day value. Monitoring of the Nova Scotia systems will continue through 1995 and strategies will be investigated. 15 figs., 5 tables

  19. Monitoring and Evaluation of Soil Conversation and Watershed Development Projects

    NARCIS (Netherlands)

    Graaff, de J.; Cameron, J.; Sombatpani, S.; Pieri, C.; Woodhill, A.J.

    2007-01-01

    Part One of this book introduces the challenges of monitoring and evaluating interventions designed by technical experts meeting the needs of people who actually use the environment which the interventions are seeking to modify. The chapters in this section seek reconciliation of these tensions thro

  20. Remote instrumentation and safeguards monitoring for the star project

    Energy Technology Data Exchange (ETDEWEB)

    Buettner, H M; Labiak, W; Spiridon, A

    2000-06-15

    A part of the Nuclear Energy Research Initiative (NERI) is the development of the Small Transportable Autonomous Reactor (STAR) for deployment in countries that do not have a nuclear industry. STARs would have an output of from 100 to 150 MW electric, would be fueled in the country of manufacture, and after 15 to 20 years of operation the reactor core would be returned to the country of manufacture for refueling. A candidate STAR design can be found in (Greenspan, 2000). This paper describes the design of the control and monitoring system that might be used. There are two unique features to this system. One is that the monitored information will be transmitted to a remote site for two purposes, safeguards, and allowing experts a great distance away direct access to view the reactor's operating parameters. The second feature is safeguards sensors will be designed into the system and there will monitoring of the safeguards aspects of the system for tampering. Any safeguards anomalies will be sent to the remote site as alarms. Encrypted satellite communications will be used to transmit the data. These features allow the STAR to be operated by a small staff and will reduce the costs of safeguards monitoring by reducing the number of plant visits by inspectors.

  1. The Web Based Monitoring Project at the CMS Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Lopez-Perez, Juan Antonio [Fermilab; Badgett, William [Fermilab; Behrens, Ulf [DESY; Chakaberia, Irakli [Kansas State U.; Jo, Youngkwon [Korea U.; Maeshima, Kaori; Maruyama, Sho [Fermilab; Patrick, James [Fermilab; Rapsevicius, Valdas [Fermilab; Soha, Aron [Fermilab; Stankevicius, Mantas [Fermilab; Sulmanas, Balys [Fermilab; Toda, Sachiko [Kansas State U.; Wan, Zongru [Kansas State U.

    2016-01-01

    The Compact Muon Solenoid is a large a complex general purpose experiment at the CERN Large Hadron Collider (LHC), built and maintained by many collaborators from around the world. Efficient operation of the detector requires widespread and timely access to a broad range of monitoring and status information. To the end the Web Based Monitoring (WBM) system was developed to present data to users located anywhere from many underlying heterogeneous sources, from real time messaging systems to relational databases. This system provides the power to combine and correlate data in both graphical and tabular formats of interest to the experimenters, including data such as beam conditions, luminosity, trigger rates, detector conditions, and many others, allowing for flexibility on the user’s side. This paper describes the WBM system architecture and describes how the system has been used from the beginning of data taking until now (Run1 and Run 2).

  2. All Sky Cloud Coverage Monitoring for SONG-China Project

    Science.gov (United States)

    Tian, J. F.; Deng, L. C.; Yan, Z. Z.; Wang, K.; Wu, Y.

    2016-05-01

    In order to monitor the cloud distributions at Qinghai station, a site selected for SONG (Stellar Observations Network Group)-China node, the design of the proto-type of all sky camera (ASC) applied in Xinglong station is adopted. Both hardware and software improvements have been made in order to be more precise and deliver quantitative measurements. The ARM (Advanced Reduced Instruction Set Computer Machine) MCU (Microcontroller Unit) instead of PC is used to control the upgraded version of ASC. A much higher reliability has been realized in the current scheme. Independent of the positions of the Sun and Moon, the weather conditions are constantly changing, therefore it is difficult to get proper exposure parameters using only the temporal information of the major light sources. A realistic exposure parameters for the ASC can actually be defined using a real-time sky brightness monitor that is also installed at the same site. The night sky brightness value is a very sensitive function of the cloud coverage, and can be accurately measured by the sky quality monitor. We study the correlation between the exposure parameter and night sky brightness value, and give the mathematical relation. The images of the all sky camera are inserted into database directly. All sky quality images are archived in FITS format which can be used for further analysis.

  3. Meshat: Monitoring and Experience Sharing Tool for Project-Based Learning

    CERN Document Server

    Michel, Christine

    2009-01-01

    Our work aims at studying tools offered to learners and tutors involved in face-to-face or blended project-based learning activities. To understand better the needs and expectations of each actor, we are especially interested in the specific case of project management training. The results of a course observation show that the lack of monitoring and expertise transfer tools involves important dysfunctions in the course organisation and therefore dissatisfaction for tutors and students (in particular about the acquisition of knowledge and expertise). So as to solve this problem, we propose a personalised platform (according to the actor: project group, student or tutor) which gives information to monitor activities and supports the acquisition and transfer of expertise. This platform is meant for the complex educational context of project-based learning. Indeed, as for the majority of project-based learning activities, the articulation conceptualisation-experiment is an important part of the process. The origi...

  4. CEM ultrasonic flow monitoring design, installation and certification results at the Salt River Project

    Energy Technology Data Exchange (ETDEWEB)

    Rihs, P.W. [Salt River Project, Saint Johns, AZ (United States). Coronado Generating Station

    1995-12-31

    This presentation will include Salt River Project`s design, installation, experiences and results using ultrasonic flow monitoring equipment for certification of continuous emissions monitoring systems. Flow Monitoring is the newest and has been the most controversial component of CEM systems. Experience in measuring flue gas volumetric flow prior to CEMs was very limited. There are currently three basic techniques used to measure gas flow: (1) thermal sensing using hotwire anemometer or thermal dispersion; (2) differential pressure (pitot tube and annubar); (3) acoustic using ultrasonic transducers. The Salt River Project (SRP) operates a variety of affected generating stations: coal, gas and oil. Ultrasonic flow monitoring technology was chosen for all affected generating stations which the author operates. SRP`s approach and reasoning for choosing ultrasonic systems will be discussed. A review of each generating station`s flow monitoring system will be presented. The presentation will include, but may not be limited to, the following: general facilities, description and schematics; physical installations, plan and section drawings; design considerations; results of flow monitors certification testing; and CEMs Project Manager`s conclusions.

  5. Project management metrics, KPIs, and dashboards a guide to measuring and monitoring project performance

    CERN Document Server

    Kerzner, Harold

    2017-01-01

    With the growth of complex projects, stakeholder involvement, and advancements in visual-based technology, metrics and KPIs (key performance indicators) are key factors in evaluating project performance. Dashboard reporting systems provide accessible project performance data, and sharing this vital data in a concise and consistent manner is a key communication responsibility of all project managers. This 3rd edition of Kerzner’s groundbreaking work includes the following updates: new sections on processing dashboard information, portfolio management PMO and metrics, and BI tool flexibility. PPT decks by chapter and a test bank will be available for use in seminar presentations and courses.

  6. Worksheet of Exogenous Variables that Impact the Success of Validation Stage of Product Delivery of a Project

    Directory of Open Access Journals (Sweden)

    Altino José Mentzingen de Moraes

    2015-02-01

    Full Text Available In the theory presented by PMBoK© - Project Management Book of Knowledge the Project Management [1] features - among others - the Disciplines of Scope and Quality. The Discipline of Scope, to become effective, must provide the execution of a hypothetical step (not defined in its text but perceived by the present author of this paper that can be termed as Planning Stage of Project Result. The Discipline of Quality, to become effective, must provide the execution of an also hypothetical step (also not defined in its text but also perceived by the same present author of this paper that can be termed as Validation Stage of Product Delivery.In the theory presented by PMBoK© - Project Management Book of Knowledge the Project Management [1] features - among others - the Disciplines of Scope and Quality. The Discipline of Scope, to become effective, must provide the execution of a hypothetical step (not defined in its text but perceived by the present author of this paper that can be termed as Planning Stage of Project Result. The Discipline of Quality, to become effective, must provide the execution of an also hypothetical step (also not defined in its text but also perceived by the same present author of this paper that can be termed as Validation Stage of Product Delivery.In the theory presented by PMBoK© - Project Management Book of Knowledge the Project Management [1] features - among others - the Disciplines of Scope and Quality. The Discipline of Scope, to become effective, must provide the execution of a hypothetical step (not defined in its text but perceived by the present author of this paper that can be termed as Planning Stage of Project Result. The Discipline of Quality, to become effective, must provide the execution of an also hypothetical step (also not defined in its text but also perceived by the same present author of this paper that can be termed as Validation Stage of Product Delivery. The importance of both Stages is crucial to

  7. The need for complementary hydraulic analysis in post-restoration monitoring of river restoration projects

    Science.gov (United States)

    Endreny, T. A.; Soulman, M. M.

    2011-03-01

    River restoration design methods are incrementally improved by studying and learning from monitoring data in previous projects. In this paper, we report post-restoration monitoring data for a Natural Channel Design (NCD) restoration project along 1600 m (10 channel wavelengths) of the Batavia Kill in the Catskill Mountains, NY, implemented in 2001 and 2002. The NCD project used a reference-reach to determine channel form, empirical relations between the project site and reference site bankfull dimensions to size channel geometry, and hydraulic and sediment computations to test channel capacity and sediment stability. In addition 12 cross-vanes and 48 j-hook vanes used in NCD for river training were installed to protect against bank erosion and maintain scour pools for fish habitat. Changes in pool depths were monitored with surveys from 2002-2004, and then after the channel-altering April 2005 flood. Aggradation in pools was attributed to cross-vane arms not concentrating flow in the center of the channel, which subsequently caused flow splitting and 4 partial point bar avulsions during the 2005 flood. Hydrodynamic simulation at the 18 m3s-1 bankfull flow suggested avulsions occurred where vanes allowed erosive bank scour to initiate the avulsion cut, and once the flow was split, the diminished in-channel flow caused more aggradation in the pools. In this project post-restoration monitoring had detected aggradation and considered it a problem. The lesson for the larger river restoration community is monitoring protocol should include complementary hydraulic and sediment analysis to comprehend potential consequences and develop preventative maintenance. River restoration and monitoring teams should be trained in robust hydraulic and sediment analytical methods that help them extend project restoration goals.

  8. The need for complementary hydraulic analysis in post-restoration monitoring of river restoration projects

    Directory of Open Access Journals (Sweden)

    T. A. Endreny

    2011-03-01

    Full Text Available River restoration design methods are incrementally improved by studying and learning from monitoring data in previous projects. In this paper, we report post-restoration monitoring data for a Natural Channel Design (NCD restoration project along 1600 m (10 channel wavelengths of the Batavia Kill in the Catskill Mountains, NY, implemented in 2001 and 2002. The NCD project used a reference-reach to determine channel form, empirical relations between the project site and reference site bankfull dimensions to size channel geometry, and hydraulic and sediment computations to test channel capacity and sediment stability. In addition 12 cross-vanes and 48 j-hook vanes used in NCD for river training were installed to protect against bank erosion and maintain scour pools for fish habitat. Changes in pool depths were monitored with surveys from 2002–2004, and then after the channel-altering April 2005 flood. Aggradation in pools was attributed to cross-vane arms not concentrating flow in the center of the channel, which subsequently caused flow splitting and 4 partial point bar avulsions during the 2005 flood. Hydrodynamic simulation at the 18 m3s−1 bankfull flow suggested avulsions occurred where vanes allowed erosive bank scour to initiate the avulsion cut, and once the flow was split, the diminished in-channel flow caused more aggradation in the pools. In this project post-restoration monitoring had detected aggradation and considered it a problem. The lesson for the larger river restoration community is monitoring protocol should include complementary hydraulic and sediment analysis to comprehend potential consequences and develop preventative maintenance. River restoration and monitoring teams should be trained in robust hydraulic and sediment analytical methods that help them extend project restoration goals.

  9. Yakima/Klickitat Fisheries Project Genetic Studies; Yakima/Klickitat Fisheries Project Monitoring and Evaluation, 2005-2006 Annual Report.

    Energy Technology Data Exchange (ETDEWEB)

    Busack, Craig A.; Fritts, Anthony L.; Kassler, Todd (Washington Department of Fish and Wildlife, Olympia, WA)

    2006-05-01

    This report covers one of many topics under the Yakima/Klickitat Fisheries Project's Monitoring and Evaluation Program (YKFPME). The YKFPME is funded under two BPA contracts, one for the Yakama Nation and the other for the Washington Department of Fish and Wildlife (Contract number 22370, Project Number 1995-063-25). A comprehensive summary report for all of the monitoring and evaluation topics will be submitted after all of the topical reports are completed. This approach to reporting enhances the ability of people to get the information they want, enhances timely reporting of results, and provides a condensed synthesis of the whole YKFPME. The current report was completed by the Washington Department of Fish and Wildlife.

  10. Permafrost and Active Layer Monitoring in the Maritime Antarctic: A Contribution to TSP and ANTPAS projects

    Science.gov (United States)

    Vieira, G.; Ramos, M.; Batista, V.; Caselli, A.; Correia, A.; Fragoso, M.; Gruber, S.; Hauck, C.; Kenderova, R.; Lopez-Martinez, J.; Melo, R.; Mendes-Victor, L. A.; Miranda, P.; Mora, C.; Neves, M.; Pimpirev, C.; Rocha, M.; Santos, F.; Blanco, J. J.; Serrano, E.; Trigo, I.; Tome, D.; Trindade, A.

    2008-12-01

    Permafrost and active layer monitoring in the Maritime Antarctic (PERMANTAR) is a Portuguese funded International Project that, in cooperation with the Spanish project PERMAMODEL, will assure the installation and the maintenance of a network of boreholes and active layer monitoring sites, in order to characterize the spatial distribution of the physical and thermal properties of permafrost, as well as the periglacial processes in Livingston and Deception Islands (South Shetlands). The project is part of the International Permafrost Association IPY projects Thermal State of Permafrost (TSP) and Antarctic and Sub-Antarctic Permafrost, Soils and Periglacial Environments (ANTPAS). It contributes to GTN-P and CALM-S networks. The PERMANTAR-PERMAMODEL permafrost and active layer monitoring network includes several boreholes: Reina Sofia hill (since 2000, 1.1m), Incinerador (2000, 2.3m), Ohridski 1 (2008, 5m), Ohridski 2 (2008, 6m), Gulbenkian-Permamodel 1 (2008, 25m) and Gulbenkian- Permamodel 2 (2008, 15m). For active layer monitoring, several CALM-S sites have been installed: Crater Lake (2006), Collado Ramos (2007), Reina Sofia (2007) and Ohridski (2007). The monitoring activities are accompanied by detailed geomorphological mapping in order to identify and map the geomorphic processes related to permafrost or active layer dynamics. Sites will be installed in early 2009 for monitoring rates of geomorphological activity in relation to climate change (e.g. solifluction, rockglaciers, thermokarst). In order to analyse the spatial distribution of permafrost and its ice content, electrical resistivity tomography (ERT), and seismic refraction surveys have been performed and, in early 2009, continuous ERT surveying instrumentation will be installed for monitoring active layer evolution. The paper presents a synthesis of the activities, as well as the results obtained up to the present, mainly relating to ground temperature monitoring and from permafrost characteristics and

  11. Hood River Monitoring and Evaluation Project, Annual Report 2002-2003.

    Energy Technology Data Exchange (ETDEWEB)

    Vaivoda, Alexis

    2004-02-01

    The Hood River Production Program Monitoring and Evaluation Project is co-managed by the Confederated Tribes of Warm Springs (CTWSRO) and the Oregon Department of Fish and Wildlife. The program is divided up to share responsibilities, provide efficiency, and avoid duplication. From October 2002 to September 2003 (FY 03) project strategies were implemented to monitor, protect, and restore anadromous fish and fish habitat in the Hood River subbasin. A description of the progress during FY 03 is reported here. Additionally an independent review of the entire program was completed in 2003. The purpose of the review was to determine if project goals and actions were achieved, look at critical uncertainties for present and future actions, determine cost effectiveness, and choose remedies that would increase program success. There were some immediate changes to the implementation of the project, but the bulk of the recommendations will be realized in coming years.

  12. MONDO Project: real time ocean monitoring through Lagrangian drifters during offshore drilling operations

    Energy Technology Data Exchange (ETDEWEB)

    Mafra, Tatiana [Eni Oil do Brasil, Rio de Janeiro, RJ (Brazil); Fragoso, Mauricio da Rocha; Santos, Francisco Alves dos; Cruz, Leonardo M. Marques A.; Pellegrini, Julio A.C.; Cerrone, Bruna Nogueira [Prooceano, Rio de Janeiro, RJ (Brazil); Assireu, Arcilan Trevenzoli [Instituto Nacional de Pesquisas Espaciais (INPE), Sao Jose dos Campos, SP (Brazil)

    2008-07-01

    Monitoring the ocean conditions during offshore operations is essential for both operational and environmental aspects. Environmentally, not only to know better the environment where the activity is taking place, but also to be able to provide fast and accurate response in case of accidents. MONDO Project (Monitoring by Ocean Drifters) is a pioneer initiative from ENI Oil do Brasil and PROOCEANO that aimed to monitor currents as a part of a metoceanographic data monitoring project of drilling operations in Brazilian Waters, in Santos Basin throughout September to November 2007, 40 satellite tracked ocean drifters were deployed will be transmitting data up to November 2008. The results of this project can be used to study a wide range of subjects about ocean dynamics. Following the principles of social and environmental responsibility, MONDO Project aims to benefit the local ecosystem in increasing the scientific knowledge of the area to calibrate hydrodynamic models that will lead to more accurate modeling results and, as a consequence, to a better management of contingency plans. Based on these principles, the project will also provide unrestricted access to oceanographic data even after the end of operations. (author)

  13. Harvard Observing Project monitoring of Boyajian's Star (KIC 8462852)

    Science.gov (United States)

    Schumer, Clea F.; Vanderburg, Andrew; Bieryla, Allyson; Carmichael, Theron; Garrison, Lehman H.; Huang, Jane; Lewis, John; Mayo, Andrew; Alam, Munazza; Gomez, Sebastian; Kamdar, Harshil; Yuan, Sihan; Cordova, Rodrigo

    2017-01-01

    Between 2009 and 2013, the Kepler spacecraft observed ~200,000 stars, repeatedly measuring their brightness to look for regular dimmings that could indicate the presence of a transiting planet (Borucki et al. 2010). This endeavor led to the discovery of thousands of planets. However, the data pertaining to one star, KIC 8462852, nicknamed “Tabby's Star” or “Boyajian's Star" indicated sporadic dimmings thought to be resulting from massive, evolving, and erratic shapes passing in front of the star (Boyajian et al. 2016, Wright and Sigurdsson 2016). Additional observations have indicated that KIC 8462852 has faded by approximately 20% over the past century (Wright and Sigurdsson 2016). Kepler is now observing other areas of space, and consequently, ground-based efforts have emerged in order to continue tracking the brightness of KIC 8462852. The Harvard Observing Project (HOP) is an observational astronomy initiative that engages undergraduate students and provides graduate students with the opportunity to lead sessions of data collection. During the fall 2016 semester, HOP will be observing KIC 8462852 in BVRI filters using Harvard's 16-inch DFM Clay telescope. We will present a light curve of the star spanning the course of three months.

  14. Characterization, Monitoring, and Risk Assessment at the IEA GHG Weyburn-Midale CO2 Monitoring and Storage Project, Saskatchewan, Canada.

    Science.gov (United States)

    Ben, R.; Chalaturnyk, R.; Gardner, C.; Hawkes, C.; Johnson, J.; White, D.; Whittaker, S.

    2008-12-01

    In July 2000, a major research project was initiated to study the geological storage of CO2 as part of a 5000 tonnes/day EOR project planned for the Weyburn Field in Saskatchewan, Canada. Major objectives of the IEA GHG Weyburn CO2 monitoring and storage project included: assessing the integrity of the geosphere encompassing the Weyburn oil pool for effective long-term storage of CO2; monitoring the movement of the injected CO2, and assessing the risk of migration of CO2 from the injection zone (approximately 1500 metres depth) to the surface. Over the period 2000-2004, a diverse group of 80+ researchers worked on: geological, geophysical, and hydrogeological characterizations at both the regional (100 km beyond the field) and detailed scale (10 km around the field); conducted time-lapse geophysical surveys; carried out surface and subsurface geochemical surveys; and undertook numerical reservoir simulations. Results of the characterization were used for a performance assessment that concluded the risk of CO2 movement to the biosphere was very small. By September 2007, more than 14 Mtonnes of CO2 had been injected into the Weyburn reservoir, including approximately 3 Mtonnes recycled from oil production. A "Final Phase" research project was initiated (2007- 2011) to contribute to a "Best Practices" guide for long-term CO2 storage in EOR settings. Research objectives include: improving the geoscience characterization; further detailed analysis and data collection on the role of wellbores; additional geochemical and geophysical monitoring activities; and an emphasis on quantitative risk assessments using multiple analysis techniques. In this talk a review of results from Phase I will be presented followed by plans and initial results for the Final Phase.

  15. Monitoring crop phenology and growth stages from space: opportunities and challenges

    Science.gov (United States)

    Crop growth stages in concert with weather and soil moisture conditions can have a significant impact on crop yields. In the U.S., crop growth stages and conditions are reported by farmers at the county level. These reports are somewhat subjective and fluctuate between different reporters, locations...

  16. Construction and Practice of Engineering Project Risk Monitoring System%工程项目风险监控体系构建与实践

    Institute of Scientific and Technical Information of China (English)

    王仲平

    2014-01-01

    This article explores the supervision and control of the whole process of the project, analyzes the risk of each stage of engineering construction monitoring and creates the project risk monitoring system, which has improved the quality and efficiency of the construction of the project.%本文通过对工程项目全过程的监督及控制进行探索,对工程建设各个阶段的风险点监控进行了分析研究,创建工程项目的风险监控体系,提高了工程项目建设的质量和效率。

  17. Multimode Process Monitoring Based on Fuzzy C-means in Locality Preserving Projection Subspace

    Institute of Scientific and Technical Information of China (English)

    解翔; 侍洪波

    2012-01-01

    For complex industrial processes with multiple operational conditions, it is important to develop effective monitoring algorithms to ensure the safety of production processes. This paper proposes a novel monitoring strategy based on fuzzy C-means. The high dimensional historical data are transferred to a low dimensional subspace spanned by locality preserving projection. Then the scores in the novel subspace are classified into several overlapped clusters, each representing an operational mode. The distance statistics of each cluster are integrated though the membership values into a novel BID (Bayesian inference distance) monitoring index. The efficiency and effectiveness of the proposed method are validated though the Tennessee Eastman benchmark process.

  18. International Energy Agency (IEA) Greenhouse Gas (GHG) Weyburn-Midale CO₂ Monitoring and Storage Project

    Energy Technology Data Exchange (ETDEWEB)

    Sacuta, Norm [Petroleum Technology Research Centre Incorporated, Saskatchewan (Canada); Young, Aleana [Petroleum Technology Research Centre Incorporated, Saskatchewan (Canada); Worth, Kyle [Petroleum Technology Research Centre Incorporated, Saskatchewan (Canada)

    2015-12-22

    The IEAGHG Weyburn-Midale CO₂ Monitoring and Storage Project (WMP) began in 2000 with the first four years of research that confirmed the suitability of the containment complex of the Weyburn oil field in southeastern Saskatchewan as a storage location for CO₂ injected as part of enhanced oil recovery (EOR) operations. The first half of this report covers research conducted from 2010 to 2012, under the funding of the United States Department of Energy (contract DEFE0002697), the Government of Canada, and various other governmental and industry sponsors. The work includes more in-depth analysis of various components of a measurement, monitoring and verification (MMV) program through investigation of data on site characterization and geological integrity, wellbore integrity, storage monitoring (geophysical and geochemical), and performance/risk assessment. These results then led to the development of a Best Practices Manual (BPM) providing oilfield and project operators with guidance on CO₂ storage and CO₂-EOR. In 2013, the USDOE and Government of Saskatchewan exercised an optional phase of the same project to further develop and deploy applied research tools, technologies, and methodologies to the data and research at Weyburn with the aim of assisting regulators and operators in transitioning CO₂-EOR operations into permanent storage. This work, detailed in the second half of this report, involves seven targeted research projects – evaluating the minimum dataset for confirming secure storage; additional overburden monitoring; passive seismic monitoring; history-matched modelling; developing proper wellbore design; casing corrosion evaluation; and assessment of post CO₂-injected core samples. The results from the final and optional phases of the Weyburn-Midale Project confirm the suitability of CO₂-EOR fields for the injection of CO₂, and further, highlight the necessary MMV and follow-up monitoring required for these operations to be considered

  19. Two-stage Framework for a Topology-Based Projection and Visualization of Classified Document Collections

    Energy Technology Data Exchange (ETDEWEB)

    Oesterling, Patrick; Scheuermann, Gerik; Teresniak, Sven; Heyer, Gerhard; Koch, Steffen; Ertl, Thomas; Weber, Gunther H.

    2010-07-19

    During the last decades, electronic textual information has become the world's largest and most important information source available. People have added a variety of daily newspapers, books, scientific and governmental publications, blogs and private messages to this wellspring of endless information and knowledge. Since neither the existing nor the new information can be read in its entirety, computers are used to extract and visualize meaningful or interesting topics and documents from this huge information clutter. In this paper, we extend, improve and combine existing individual approaches into an overall framework that supports topological analysis of high dimensional document point clouds given by the well-known tf-idf document-term weighting method. We show that traditional distance-based approaches fail in very high dimensional spaces, and we describe an improved two-stage method for topology-based projections from the original high dimensional information space to both two dimensional (2-D) and three dimensional (3-D) visualizations. To show the accuracy and usability of this framework, we compare it to methods introduced recently and apply it to complex document and patent collections.

  20. Monitoring and Evaluating Projects : A Step-by-Step Primer on Monitoring, Benchmarking, and Impact Evaluation

    OpenAIRE

    Rebekka E. Grun

    2006-01-01

    This paper attempts to be a practical step-by-step guide to prepare and carry out benchmarking and impact analyses of projects. It's purpose is to attempt to present analytical tools solidly grounded in economic theory all while focusing on the practical questions of evaluations. Little space is given to theory, in order to spend more time on the actual steps involved, trying to make this ...

  1. The Umatilla Basin Natural Production Monitoring and Evaluation Project, 2008 Annual Progress Report.

    Energy Technology Data Exchange (ETDEWEB)

    Contor, Craig R.; Harris, Robin; King, Marty [Confederated Tribes of the Umatilla Indian Reservation

    2009-06-10

    The Umatilla Basin Natural Production Monitoring and Evaluation Project (UBNPMEP) is funded by Bonneville Power Administration (BPA) as directed by section 4(h) of the Pacific Northwest Electric Power Planning and Conservation Act of 1980 (P.L.96-501). This project is in accordance with and pursuant to measures 4.2A, 4.3C.1, 7.1A.2, 7.1C.3, 7.1C.4 and 7.1D.2 of the Northwest Power Planning Council's (NPPC) Columbia River Basin Fish and Wildlife Program (NPPC 1994). Work was conducted by the Fisheries Program of the Confederated Tribes of the Umatilla Indian Reservation (CTUIR). The UBNPMEP is coordinated with two Oregon Department of Fish and Wildlife (ODFW) research projects that also monitor and evaluate the success of the Umatilla Fisheries Restoration Plan. This project deals with the natural production component of the plan, and the ODFW projects evaluate hatchery operations (project No. 1990-005-00, Umatilla Hatchery M & E) and smolt outmigration (project No. 1989-024-01, Evaluation of Juvenile Salmonid Outmigration and Survival in the Lower Umatilla River). Collectively these three projects monitor and evaluate natural and hatchery salmonid production in the Umatilla River Basin. The need for natural production monitoring has been identified in multiple planning documents including Wy-Kan-Ush-Mi Wa-Kish-Wit Volume I, 5b-13 (CRITFC 1996), the Umatilla Hatchery Master Plan (CTUIR & ODFW 1990), the Umatilla Basin Annual Operation Plan, the Umatilla Subbasin Summary (CTUIR & ODFW 2001), the Subbasin Plan (CTUIR & ODFW 2004), and the Comprehensive Research, Monitoring, and Evaluation Plan (CTUIR and ODFW 2006). Natural production monitoring and evaluation is also consistent with Section III, Basinwide Provisions, Strategy 9 of the 2000 Columbia River Basin Fish and Wildlife Program (NPPC 1994, NPCC 2004). The Umatilla Basin M&E plan developed along with efforts to restore natural populations of spring and fall Chinook salmon, (Oncorhynchus tshawytsha), coho

  2. Protocols for Monitoring Habitat Restoration Projects in the Lower Columbia River and Estuary

    Energy Technology Data Exchange (ETDEWEB)

    Roegner, G. Curtis; Diefenderfer, Heida L.; Borde, Amy B.; Thom, Ronald M.; Dawley, Earl M.; Whiting, Allan H.; Zimmerman, Shon A.; Johnson, Gary E.

    2008-04-25

    Protocols for monitoring salmon habitat restoration projects are essential for the U.S. Army Corps of Engineers' environmental efforts in the Columbia River estuary. This manual provides state-of-the science data collection and analysis methods for landscape features, water quality, and fish species composition, among others.

  3. Preliminary evaluation of a prototype welfare monitoring system for sows and piglets (Welfare Quality (R) project)

    NARCIS (Netherlands)

    Scott, K.; Binnendijk, G.P.; Edwards, S.A.; Gu, J.H.; Wijhe-Kiezebrink, van M.C.; Vermeer, H.M.

    2009-01-01

    The Welfare Quality(R) project aims to develop a European on-form welfare assessment standard for pigs, amongst other species. A prototype monitoring system was developed for sows and piglets using predominantly animal-based measures of behaviour, health and physiology to assess welfare. The

  4. Modeling radiation conditions in orbits of projected system of small satellites for radiation monitoring

    Science.gov (United States)

    Panasyuk, M. I.; Podzolko, M. V.; Kovtyukh, A. S.; Osedlo, V. I.; Tulupov, V. I.; Yashin, I. V.

    2016-11-01

    Calculated estimates are presented for the accumulated radiation doses behind the shields of various thicknesses in the orbits of projected at Skobeltsyn Institute of Nuclear Physics, Moscow State University system of small satellites for radiation monitoring. The results are analyzed and compared with the calculation data for other actively exploited near-Earth orbits.

  5. Outcome mapping as methodology to monitor and evaluate community informatics projects: A case study

    CSIR Research Space (South Africa)

    Herselman, M

    2010-10-01

    Full Text Available The purpose of this paper is to indicate how Outcome Mapping (OM) can be used as a methodology to monitor and evaluate a specific developmental informatics project currently under way in the Meraka Institute. OM was applied in the Broadband for All...

  6. Preliminary evaluation of a prototype welfare monitoring system for sows and piglets (Welfare Quality (R) project)

    NARCIS (Netherlands)

    Scott, K.; Binnendijk, G.P.; Edwards, S.A.; Gu, J.H.; Wijhe-Kiezebrink, van M.C.; Vermeer, H.M.

    2009-01-01

    The Welfare Quality(R) project aims to develop a European on-form welfare assessment standard for pigs, amongst other species. A prototype monitoring system was developed for sows and piglets using predominantly animal-based measures of behaviour, health and physiology to assess welfare. The prototy

  7. Integrating a project monitoring system into a public health network: experiences from Alive & Thrive Vietnam.

    Science.gov (United States)

    Tuan, Nguyen Thanh; Alayon, Silvia; Do, Tran Thanh; Ngan, Tran Thi; Hajeebhoy, Nemat

    2015-01-01

    Little information is available about how to build a monitoring system to measure the output of preventive nutrition interventions, such as counselling on infant and young child feeding. This paper describes the Alive & Thrive Vietnam (A&T) project experience in nesting a large-scale project monitoring system into the existing public health information system (e.g. using the system and resources), and in using monitoring data to strengthen service delivery in 15 provinces with A&T franchises. From January 2012 to April 2014, the 780 A&T franchises provided 1,700,000 counselling contacts (~3/4 by commune franchises). In commune franchises in April 2014, 80% of mothers who were pregnant or with children under two years old had been to the counselling service at least one time, and 87% of clients had been to the service earlier. Monitoring data are used to track the progress of the project, make decisions, provide background for a costing study and advocate for the integration of nutrition counselling indicators into the health information system nationwide. With careful attention to the needs of stakeholders at multiple levels, clear data quality assurance measures and strategic feedback mechanisms, it is feasible to monitor the scale-up of nutrition programmes through the existing routine health information system.

  8. 4 Kelvin Cooling with Innovative Final Stage of Multistage Cryocooler Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Proposed for development is a proof-of-concept prototype for the final stage of a multistage cryocooler. This final stage comprises a high frequency pulse tube cold...

  9. Overview of vegetation monitoring data, 1952--1983. Hanford Environmental Dose Reconstruction Project

    Energy Technology Data Exchange (ETDEWEB)

    Duncan, J.P.

    1994-03-01

    This report is a result of the Hanford Environmental Dose Reconstruction (HEDR) Project. The goal of the HEDR Project is to estimate the radiation dose that individuals could have received from emissions since 1944 at the Hanford Site near Richland, Washington. Members of the HEDR Project`s Environmental Monitoring Data Task have developed databases of historical environmental measurements of such emissions. The HEDR Project is conducted by Battelle, Pacific Northwest Laboratories. This report is the third in a series that documents the information available on measurements of iodine-131 concentrations in vegetation. The first two reports provide the data for 1945--1951. This report provides an overview of the historical documents, which contain vegetation data for 1952--1983. The overview is organized according to the documents available for any given year. Each section, covering one year, contains a discussion of the media sampled, the sampling locations, significant events if there were any, emission quantities, constituents measured, and a list of the documents with complete reference information. Because the emissions which affected vegetation were significantly less after 1951, the vegetation monitoring data after that date have not been used in the HEDR Project. However, access to these data may be of interest to the public. This overview is, therefore, being published.

  10. Statistical process monitoring based on orthogonal multi-manifold projections and a novel variable contribution analysis.

    Science.gov (United States)

    Tong, Chudong; Shi, Xuhua; Lan, Ting

    2016-11-01

    Multivariate statistical methods have been widely applied to develop data-based process monitoring models. Recently, a multi-manifold projections (MMP) algorithm was proposed for modeling and monitoring chemical industrial processes, the MMP is an effective tool for preserving the global and local geometric structure of the original data space in the reduced feature subspace, but it does not provide orthogonal basis functions for data reconstruction. Recognition of this issue, an improved version of MMP algorithm named orthogonal MMP (OMMP) is formulated. Based on the OMMP model, a further processing step and a different monitoring index are proposed to model and monitor the variation in the residual subspace. Additionally, a novel variable contribution analysis is presented for fault diagnosis by integrating the nearest in-control neighbor calculation and reconstruction-based contribution analysis. The validity and superiority of the proposed fault detection and diagnosis strategy are then validated through case studies on the Tennessee Eastman benchmark process.

  11. Experimental analysis of vehicle-bridge interaction using a wireless monitoring system and a two-stage system identification technique

    Science.gov (United States)

    Kim, Junhee; Lynch, Jerome P.

    2012-04-01

    Deterioration of bridges under repeated traffic loading has called attention to the need for improvements in the understanding of vehicle-bridge interaction. While analytical and numerical models have been previously explored to describe the interaction that exists between a sprung mass (i.e., a moving vehicle) and an elastic beam (i.e., bridge), comparatively less research has been focused on the experimental observation of vehicle-bridge interaction. A wireless monitoring system with wireless sensors installed on both the bridge and moving vehicle is proposed to record the dynamic interaction between the bridge and vehicle. Time-synchronized vehicle-bridge response data is used within a two-stage system identification methodology. In the first stage, the free-vibration response of the bridge is used to identify the dynamic characteristics of the bridge. In the second stage, the vehicle-bridge response data is used to identify the time varying load imposed on the bridge from the vehicle. To test the proposed monitoring and system identification strategy, the 180 m long Yeondae Bridge (Icheon, Korea) was selected. A dense network of wireless sensors was installed on the bridge while wireless sensors were installed on a multi-axle truck. The truck was driven across the bridge at constant velocity with bridge and vehicle responses measured. Excellent agreement between the measured Yeondae Bridge response and that predicted by an estimated vehicle-bridge interaction model validates the proposed strategy.

  12. Nearshore and offshore environmental effects monitoring at the Sable Offshore Energy project

    Energy Technology Data Exchange (ETDEWEB)

    Hurley, G. V. [Sable Offshore Energy Inc, Halifax, NS (Canada)

    2000-07-01

    A monitoring program to determine whether any temporary or permanent environmental perturbations may be attributable to the Sable offshore gas pipeline project as it approaches landfall at Goldboro through an outer bay is discussed, This nearshore region is an active fishing region for the residents of Goldboro, hence the concern about possible contamination. The monitoring project began with a baseline study, followed by monitoring the construction and the recovery period following construction, to ensure that any persistent changes to the nearshore aquatic environment were documented. The monitoring study included representatives of the fishing community to ensure that concerns are addressed early and on a continuing basis. At various phases of the project water properties,sediment modelling, the effects of construction on sea bottom conditions, benthic biota and cultivated mussels, water quality, phytoplankton, and resuspension of toxic cysts, terns and other seabirds were studied. Monitoring programs were also established for sea urchins and mussels, two important commercial species. Commercial-sized sea urchins showed a decrease of 60 per cent between 1998 and 1999 (i.e. the construction period). Recovery of sea urchin population in the immediate trench region will be the special focus of the post-construction monitoring phase. Mussel spat settlement and mussel tissue condition, lobster trapping, water properties, and bird behaviour showed no measurable changes during construction monitoring. In addition to these studies there is an ongoing offshore monitoring program in effect by Sable Offshore Energy Inc., put in place as a condition of approval of its Development Plan by the Canada-Nova Scotia Offshore Petroleum Board. This program monitors attributes such as water quality, suspended particulate matter in the benthic boundary layer, sediment quality, the benthic habitat and megafaunal community, shellfish body burden and taint, marine mammals and seabirds

  13. Annual report for RCRA groundwater monitoring projects at Hanford Site facilities for 1993

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    This report presents the annual hydrogeologic evaluation of 20 Resource Conservation and Recovery Act of 1976 groundwater monitoring projects and 1 nonhazardous waste facility at the US Department of Energy`s Hanford Site. Most of the projects no longer receive dangerous waste; a few projects continue to receive dangerous waste constituents for treatment, storage, or disposal. The 20 RCRA projects comprise 30 waste management units. Ten of the units are monitored under groundwater quality assessment status because of elevated levels of indicator parameters. The impact of those units on groundwater quality, if any, is being investigated. If dangerous waste or waste constituents have entered groundwater, their concentration, distribution, and rate of migration are evaluated. Groundwater is monitored at the other 20 units to detect contamination, should it occur. This report provides an interpretation of groundwater data collected at the waste management units between October 1992 and September 1993. Recent groundwater quality is also described for the 100, 200, 300, and 600 Areas and for the entire Hanford Site. Widespread contaminants include nitrate, chromium, carbon tetrachloride, tritium, and other radionuclides.

  14. Transport infrastructure surveillance and monitoring by electromagnetic sensing: the ISTIMES project.

    Science.gov (United States)

    Proto, Monica; Bavusi, Massimo; Bernini, Romeo; Bigagli, Lorenzo; Bost, Marie; Bourquin, Frédrèric; Cottineau, Louis-Marie; Cuomo, Vincenzo; Della Vecchia, Pietro; Dolce, Mauro; Dumoulin, Jean; Eppelbaum, Lev; Fornaro, Gianfranco; Gustafsson, Mats; Hugenschmidt, Johannes; Kaspersen, Peter; Kim, Hyunwook; Lapenna, Vincenzo; Leggio, Mario; Loperte, Antonio; Mazzetti, Paolo; Moroni, Claudio; Nativi, Stefano; Nordebo, Sven; Pacini, Fabrizio; Palombo, Angelo; Pascucci, Simone; Perrone, Angela; Pignatti, Stefano; Ponzo, Felice Carlo; Rizzo, Enzo; Soldovieri, Francesco; Taillade, Fédrèric

    2010-01-01

    The ISTIMES project, funded by the European Commission in the frame of a joint Call "ICT and Security" of the Seventh Framework Programme, is presented and preliminary research results are discussed. The main objective of the ISTIMES project is to design, assess and promote an Information and Communication Technologies (ICT)-based system, exploiting distributed and local sensors, for non-destructive electromagnetic monitoring of critical transport infrastructures. The integration of electromagnetic technologies with new ICT information and telecommunications systems enables remotely controlled monitoring and surveillance and real time data imaging of the critical transport infrastructures. The project exploits different non-invasive imaging technologies based on electromagnetic sensing (optic fiber sensors, Synthetic Aperture Radar satellite platform based, hyperspectral spectroscopy, Infrared thermography, Ground Penetrating Radar-, low-frequency geophysical techniques, Ground based systems for displacement monitoring). In this paper, we show the preliminary results arising from the GPR and infrared thermographic measurements carried out on the Musmeci bridge in Potenza, located in a highly seismic area of the Apennine chain (Southern Italy) and representing one of the test beds of the project.

  15. Transport Infrastructure Surveillance and Monitoring by Electromagnetic Sensing: The ISTIMES Project

    Directory of Open Access Journals (Sweden)

    Marie Bost

    2010-11-01

    Full Text Available The ISTIMES project, funded by the European Commission in the frame of a joint Call “ICT and Security” of the Seventh Framework Programme, is presented and preliminary research results are discussed. The main objective of the ISTIMES project is to design, assess and promote an Information and Communication Technologies (ICT-based system, exploiting distributed and local sensors, for non-destructive electromagnetic monitoring of critical transport infrastructures. The integration of electromagnetic technologies with new ICT information and telecommunications systems enables remotely controlled monitoring and surveillance and real time data imaging of the critical transport infrastructures. The project exploits different non-invasive imaging technologies based on electromagnetic sensing (optic fiber sensors, Synthetic Aperture Radar satellite platform based, hyperspectral spectroscopy, Infrared thermography, Ground Penetrating Radar-, low-frequency geophysical techniques, Ground based systems for displacement monitoring. In this paper, we show the preliminary results arising from the GPR and infrared thermographic measurements carried out on the Musmeci bridge in Potenza, located in a highly seismic area of the Apennine chain (Southern Italy and representing one of the test beds of the project.

  16. Project monitoring and evaluation: an enhancing method for health research system management.

    Science.gov (United States)

    Djalalinia, Shirin; Owlia, Parviz; Malekafzali, Hossein; Ghanei, Mostafa; Babamahmoodi, Abdolreza; Peykari, Niloofar

    2014-04-01

    Planning, organizing, staffing, leading and monitoring are the basic functional component of management. In present article, we aim to define the project monitoring and evaluation in health research system (HRS) considering its success and challenges based on our national experience. IN THIS STUDY BASED ON THE INFORMATION OF ANNUAL MEDICAL SCIENCE UNIVERSITIES EVALUATION DURING THE LAST DECADE THE HRS INDICATORS HAVE BEEN SCORED IN THREE AXES BASED ON HRS FUNCTIONS: Stewardship, capacity building and knowledge production. In this article, we will focus on the results of HRS evaluation from 2002 to 2010, also on its success and challenges. In an overall view, the main results are the experiences of the designing and implantation of such process after pre-project preparation, all parts followed under the whole supervision of the aims of the HRS evaluation. Project management light the way of practical application of knowledge, skills, tools and techniques for better HRS evaluation and management. We concluded that; although monitoring and evaluation as an essential part of HRS Management light the improvement ahead way but we still need to advantage of the new project management advances.

  17. Applicability of the "Frame of Reference" approach for environmental monitoring of offshore renewable energy projects.

    Science.gov (United States)

    Garel, Erwan; Rey, Cibran Camba; Ferreira, Oscar; van Koningsveld, Mark

    2014-08-01

    This paper assesses the applicability of the Frame of Reference (FoR) approach for the environmental monitoring of large-scale offshore Marine Renewable Energy (MRE) projects. The focus is on projects harvesting energy from winds, waves and currents. Environmental concerns induced by MRE projects are reported based on a classification scheme identifying stressors, receptors, effects and impacts. Although the potential effects of stressors on most receptors are identified, there are large knowledge gaps regarding the corresponding (positive and negative) impacts. In that context, the development of offshore MRE requires the implementation of fit-for-purpose monitoring activities aimed at environmental protection and knowledge development. Taking European legislation as an example, it is suggested to adopt standardized monitoring protocols for the enhanced usage and utility of environmental indicators. Towards this objective, the use of the FoR approach is advocated since it provides guidance for the definition and use of coherent set of environmental state indicators. After a description of this framework, various examples of applications are provided considering a virtual MRE project located in European waters. Finally, some conclusions and recommendations are provided for the successful implementation of the FoR approach and for future studies.

  18. Collaborative Systemwide Monitoring and Evaluation Project (CSMEP) - Year 5 : Annual Report for FY 2008.

    Energy Technology Data Exchange (ETDEWEB)

    Marmorek, David R.; Porter, Marc; Pickard, Darcy; Wieckowski, Katherine

    2008-11-19

    The Collaborative Systemwide Monitoring and Evaluation Project (CSMEP) is a coordinated effort to improve the quality, consistency, and focus of fish population and habitat data to answer key monitoring and evaluation questions relevant to major decisions in the Columbia River Basin. CSMEP was initiated by the Columbia Basin Fish and Wildlife Authority (CBFWA) in October 2003. The project is funded by the Bonneville Power Administration (BPA) through the Northwest Power and Conservation Council's Fish and Wildlife Program (NPCC). CSMEP is a major effort of the federal state and Tribal fish and wildlife managers to develop regionally integrated monitoring and evaluation (M&E) across the Columbia River Basin. CSMEP has focused its work on five monitoring domains: status and trends monitoring of populations and action effectiveness monitoring of habitat, harvest, hatcheries, and the hydrosystem. CSMEP's specific goals are to: (1) interact with federal, state and tribal programmatic and technical entities responsible for M&E of fish and wildlife, to ensure that work plans developed and executed under this project are well integrated with ongoing work by these entities; (2) document, integrate, and make available existing monitoring data on listed salmon, steelhead, bull trout and other fish species of concern; (3) critically assess strengths and weaknesses of these data for answering key monitoring questions; and (4) collaboratively design, implement and evaluate improved M&E methods with other programmatic entities in the Pacific Northwest. During FY2008 CSMEP biologists continued their reviews of the strengths and weaknesses (S&W) of existing subbasin inventory data for addressing monitoring questions about population status and trends at different spatial and temporal scales. Work was focused on Lower Columbia Chinook and steelhead, Snake River fall Chinook, Upper Columbia Spring Chinook and steelhead, and Middle Columbia River Chinook and steelhead. These

  19. Collaborative Systemwide Monitoring and Evaluation Project (CSMEP) - Year 5 : Annual Report for FY 2008.

    Energy Technology Data Exchange (ETDEWEB)

    Marmorek, David R.; Porter, Marc; Pickard, Darcy; Wieckowski, Katherine

    2008-11-19

    The Collaborative Systemwide Monitoring and Evaluation Project (CSMEP) is a coordinated effort to improve the quality, consistency, and focus of fish population and habitat data to answer key monitoring and evaluation questions relevant to major decisions in the Columbia River Basin. CSMEP was initiated by the Columbia Basin Fish and Wildlife Authority (CBFWA) in October 2003. The project is funded by the Bonneville Power Administration (BPA) through the Northwest Power and Conservation Council's Fish and Wildlife Program (NPCC). CSMEP is a major effort of the federal state and Tribal fish and wildlife managers to develop regionally integrated monitoring and evaluation (M&E) across the Columbia River Basin. CSMEP has focused its work on five monitoring domains: status and trends monitoring of populations and action effectiveness monitoring of habitat, harvest, hatcheries, and the hydrosystem. CSMEP's specific goals are to: (1) interact with federal, state and tribal programmatic and technical entities responsible for M&E of fish and wildlife, to ensure that work plans developed and executed under this project are well integrated with ongoing work by these entities; (2) document, integrate, and make available existing monitoring data on listed salmon, steelhead, bull trout and other fish species of concern; (3) critically assess strengths and weaknesses of these data for answering key monitoring questions; and (4) collaboratively design, implement and evaluate improved M&E methods with other programmatic entities in the Pacific Northwest. During FY2008 CSMEP biologists continued their reviews of the strengths and weaknesses (S&W) of existing subbasin inventory data for addressing monitoring questions about population status and trends at different spatial and temporal scales. Work was focused on Lower Columbia Chinook and steelhead, Snake River fall Chinook, Upper Columbia Spring Chinook and steelhead, and Middle Columbia River Chinook and steelhead. These

  20. The International Remote Monitoring Project -- First results of the Argentina nuclear power station field trial

    Energy Technology Data Exchange (ETDEWEB)

    Bonino, A.; Pizarro, L.; Perez, A. [Ente Nacional Regulador Nuclear, Buenos Aires (Argentina); Schoeneman, J.L.; Dupree, S.A.; Martinez, R.L. [Sandia National Labs., Albuquerque, NM (United States); Maxey, C. [Oak Ridge National Lab., TN (United States)

    1995-12-31

    As part of the International Remote Monitoring Project field trials, during the month of March, 1995 a Remote Monitoring System (RMS) was installed at the Embalse Nuclear Power Station in Embalse, Argentina. This system monitors the status of four typical Candu spent fuel dry storage silos. The monitoring equipment for each silo consists of analog temperature and gamma radiation sensors and digital motion and electronic fiber-optic seals connected to a wireless Authenticate Item Monitoring System (AIMS). All sensor data are authenticated and transmitted via RF link to Receiver Processor Units (RPU) coupled to Remote Monitoring System equipment located in a nearby IAEA/ENREN inspector office. One of these RPUs is connected to Remote Monitoring equipment capable of information transmission (via commercial telephone links) to Data Review Stations (DRS) at ENREN laboratories in Buenos Aires, Argentina, and at Sandia National Laboratories, Albuquerque, New Mexico. The other RPU is used for on-site data storage and analysis. It is anticipated that this information will soon be transmitted to a DRS at the ABACC facility in Rio de Janeiro, Brazil. During these trials site data will be collected and analyzed periodically from Buenos Aires, Albuquerque, and Rio de Janeiro. Installation detail and data analysis will be presented in this paper.

  1. Quality of care and monitoring in paediatric end stage renal disease

    NARCIS (Netherlands)

    van Huis, M.

    2016-01-01

    In this thesis quality of care and monitoring of chronic kidney disease - mineral bone disorder (CKD-MBD) and cardiovascular disease (CVD) is assessed. Practices and policies with regards to transplantation, growth hormone and hypertension are inventories and compared with current guidelines and lit

  2. Sustainable Seas Student Monitoring Project at the Branson School in Ross, CA

    Science.gov (United States)

    Rainsford, A.; Soave, K.; Costolo, R.; Kudler, J.; Emunah, M.; Hatfield, J.; Kiyasu, J.

    2015-12-01

    Alina Rainsford, Kathy Soave, Julia Kudler, Jane Hatfield, Melea Emunah, Rose Costelo, Jenna Kiyasu, Amy Dean and Sustainable Seas Monitoring Project, Branson School, Ross, CA, United States, Farallones Marine Sanctuary Association, San Francisco, CA, United StatesAbstract:The Sustainable Seas Student Monitoring Project at the Branson School in Ross, CA has monitored Duxbury Reef in Bolinas, CA since 1999, in cooperation with the Farallones Marine Sanctuary Association and the Gulf of Farallones National Marine Sanctuary. Goals of this student-run project include: 1) To monitor the rocky intertidal habitat and develop a baseline database of invertebrates and algal density and abundance; 2) To contribute to the conservation of the rocky intertidal habitat through education of students and visitors about intertidal species; 3) To increase stewardship in the Gulf of the Farallones National Marine Sanctuary; and 4) To contribute abundance and population data on key algae and invertebrate species to the national database, LiMPETS (Long Term Monitoring Program & Experiential Training for Students). Each fall student volunteers complete an intensive training course on the natural history of intertidal invertebrates and algae, identification of key species, rocky intertidal monitoring techniques, and history of the sanctuary. Students identify and count key invertebrate and algae species along two permanent transects and, using randomly determined points, within two permanent 200 m2 areas, in fall, winter, and late spring. Using data from the previous years, we will compare population densities, seasonal abundance and long-term population trends of key algal and invertebrate species, including Tegula funebralis, Anthopluera elegantissima, Cladophora sp. and Fucus sp.. Future analyses and investigations will include intertidal abiotic factors (including water temperature, pH and human foot-traffic) to enhance insights into the Duxbury Reef ecosystem, in particular, the high

  3. The LIFE ProjectMonitoring of insects with public participation” (MIPP: aims, methods and conclusions

    Directory of Open Access Journals (Sweden)

    Giuseppe Maria Carpaneto

    2017-08-01

    Full Text Available The Life ProjectMonitoring of insects with public participation” (LIFE11 NAT/IT/000252 had as the main objective to develop and test methods for the monitoring of five beetle species listed in the Annexes of the Habitats Directive (92/43/EEC: Osmoderma eremita (hermit beetle, Scarabaeidae, Lucanus cervus (European stag beetle, Lucanidae, Cerambyx cerdo (great capricorn beetle, Cerambycidae, Rosalia alpina (rosalia longicorn, Cerambycidae and Morimus asper/funereus (morimus longicorn, Cerambycidae. The data gathered represent an important contribution to the monitoring of these target species in Italy. The methods developed for monitoring of the target species are intended for use by the local management authorities and staff of protected areas. These developed methods are the result of extensive fieldwork and ensure scientific validity, ease of execution and limited labour costs. The detailed description of methods and the results for each species are published in separate articles of this special issue of Nature Conservation. A second objective of the project was to gather faunistic data with a Citizen Science approach, using the web and a mobile application software (app specifically built for mobile devices. The validation of the records collected by the citizens was carried out by experts, based on photographs, which were obligatory for all records. Dissemination activities represented the principal way to contact and engage citizens for the data collection and also offered the possibility of providing information on topics such as Natura 2000, the Habitats Directive, the role of monitoring in nature conservation, the importance of forest ecosystems and the ecological role of the saproxylic insects. An innovative method tested during the project was the training of a dog for searching and monitoring the elusive hermit beetle; the trained dog also added a “curiosity” factor to attract public attention towards this rare insect and

  4. British Columbia S-2000 monitoring project, vol. 1, performance summary: Interim report, June 1993--December 1993

    Energy Technology Data Exchange (ETDEWEB)

    Makuch, P.D.

    1994-12-31

    The S-2000 program was established to promote cooperation between CANMET, electrical utilities, and provincial governments interested in evaluation on whether solar domestic hot water (SDHW) systems are suited to the reduction of peak electrical load levels and pollutant emission control through cost-effective energy displacement. Current activity consists of cooperative pilot projects between government and utilities to install and monitor several SDHW systems across Canada. As a first step to demonstrate the potential of SDHW in British Columbia, eight systems were purchased by B.C. Hydro and West Kootenay Power and installed on private residences throughout the province. This interim report summarizes the monitoring results from June-December 1993.

  5. The Transit Monitoring in the South (TraMoS project

    Directory of Open Access Journals (Sweden)

    López-Morales Mercedes

    2013-04-01

    Full Text Available We present the Transit Monitoring in the South (TraMoS project. TraMoS has monitored transits of 30 exoplanets with telescopes located in Chile since 2008, whit the following goals: (1 to refine the physical and/or orbital parameters of those exoplanet system, and (2 to search for variations in the mid-times of the transits and in other parameters such as orbital inclination or transit's depth, that could indicate the presence of additional bodies in the system. We highlight here the first results of TraMoS in three selected exoplanets.

  6. The Satellite based Monitoring Initiative for Regional Air quality (SAMIRA): Project summary and first results

    Science.gov (United States)

    Schneider, Philipp; Stebel, Kerstin; Ajtai, Nicolae; Diamandi, Andrei; Horalek, Jan; Nemuc, Anca; Stachlewska, Iwona; Zehner, Claus

    2017-04-01

    We present a summary and some first results of a new ESA-funded project entitled Satellite based Monitoring Initiative for Regional Air quality (SAMIRA), which aims at improving regional and local air quality monitoring through synergetic use of data from present and upcoming satellite instruments, traditionally used in situ air quality monitoring networks and output from chemical transport models. Through collaborative efforts in four countries, namely Romania, Poland, the Czech Republic and Norway, all with existing air quality problems, SAMIRA intends to support the involved institutions and associated users in their national monitoring and reporting mandates as well as to generate novel research in this area. The primary goal of SAMIRA is to demonstrate the usefulness of existing and future satellite products of air quality for improving monitoring and mapping of air pollution at the regional scale. A total of six core activities are being carried out in order to achieve this goal: Firstly, the project is developing and optimizing algorithms for the retrieval of hourly aerosol optical depth (AOD) maps from the Spinning Enhanced Visible and InfraRed Imager (SEVIRI) onboard of Meteosat Second Generation. As a second activity, SAMIRA aims to derive particulate matter (PM2.5) estimates from AOD data by developing robust algorithms for AOD-to-PM conversion with the support from model- and Lidar data. In a third activity, we evaluate the added value of satellite products of atmospheric composition for operational European-scale air quality mapping using geostatistics and auxiliary datasets. The additional benefit of satellite-based monitoring over existing monitoring techniques (in situ, models) is tested by combining these datasets using geostatistical methods and demonstrated for nitrogen dioxide (NO2), sulphur dioxide (SO2), and aerosol optical depth/particulate matter. As a fourth activity, the project is developing novel algorithms for downscaling coarse

  7. Project on restaurant energy performance: end-use monitoring and analysis. Appendixes I and II

    Energy Technology Data Exchange (ETDEWEB)

    Claar, C.N.; Mazzucchi, R.P.; Heidell, J.A.

    1985-05-01

    This is the second volume of the report, ''The Porject on Restaurant Energy Performance - End-Use Monitoring and Analysis''. The first volume (PNL-5462) contains a summary and analysis of the metered energy performance data collected by the Project on Restaurant Energy Performance (PREP). Appendix I, presented here, contains monitoring site descriptions, measurement plans, and data summaries for the seven restaurants metered for PREP. Appendix II, also in this volume, is a description of the PREP computer system.

  8. Project 57 Air Monitoring Report: October 1, 2013, through December 31, 2014

    Energy Technology Data Exchange (ETDEWEB)

    Mizell, Steve A. [Desert Research Inst. (DRI), Las Vegas, NV (United States); Nikolich, George [Desert Research Inst. (DRI), Las Vegas, NV (United States); McCurdy, Greg [Desert Research Inst. (DRI), Reno, NV (United States); Shadel, Craig [Desert Research Inst. (DRI), Las Vegas, NV (United States); Miller, Julianne J. [Desert Research Inst. (DRI), Las Vegas, NV (United States)

    2016-02-01

    On April 24, 1957, the Atomic Energy Commission (AEC, now the Department of Energy [DOE]) conducted the Project 57 safety experiment in western Emigrant Valley north east of the Nevada National Security Site (NNSS, formerly the Nevada Test Site) on lands withdrawn by the Department of Defense (DoD) for the Nevada Test and Training Range (NTTR). The test was undertaken to develop (1) a means of estimating plutonium distribution resulting from a nonnuclear detonation; (2) biomedical evaluation techniques for use in plutonium-laden environments; (3) methods of surface decontamination; and (4) instruments and field procedures for prompt estimation of alpha contamination (Shreve, 1958). Although the test did not result in the fission of nuclear materials, it did disseminate plutonium across the land surface. Following the experiment, the AEC fenced the contaminated area and returned control of the surrounding land to the DoD. Various radiological surveys have been performed in the area and in 2007, the DOE expanded the demarked contamination area by posting signs 200 to 400 feet (60 to 120 meters) outside of the original fence. Plutonium in soil is thought to attach preferentially to smaller particles. Therefore, redistribution of soil particulates by wind (dust) is the mechanism most likely to transport plutonium beyond the boundary of the Project 57 contamination area. In 2011, DRI installed two instrumentation towers to measure radiological, meteorological, and dust conditions. The monitoring activity was implemented to determine if radionuclide contamination was detectable in samples of airborne dust and characterize meteorological and environmental parameters that influence dust transport. Collected data also permits comparison of radiological conditions at the Project 57 monitoring stations to conditions observed at Community Environmental Monitoring Program (CEMP) stations around the NTTR. Biweekly samples of airborne particulates are submitted for laboratory

  9. Project 57 Air Monitoring Report: October 1, 2013, through December 31, 2014

    Energy Technology Data Exchange (ETDEWEB)

    Mizell, Steve A. [Desert Research Inst. (DRI), Las Vegas, NV (United States); Nikolich, George [Desert Research Inst. (DRI), Las Vegas, NV (United States); McCurdy, Greg [Desert Research Inst. (DRI), Reno, NV (United States); Shadel, Craig [Desert Research Inst. (DRI), Las Vegas, NV (United States); Miller, Julianne J. [Desert Research Inst. (DRI), Las Vegas, NV (United States)

    2016-02-01

    On April 24, 1957, the Atomic Energy Commission (AEC, now the Department of Energy [DOE]) conducted the Project 57 safety experiment in western Emigrant Valley north east of the Nevada National Security Site (NNSS, formerly the Nevada Test Site) on lands withdrawn by the Department of Defense (DoD) for the Nevada Test and Training Range (NTTR). The test was undertaken to develop (1) a means of estimating plutonium distribution resulting from a nonnuclear detonation; (2) biomedical evaluation techniques for use in plutonium-laden environments; (3) methods of surface decontamination; and (4) instruments and field procedures for prompt estimation of alpha contamination (Shreve, 1958). Although the test did not result in the fission of nuclear materials, it did disseminate plutonium across the land surface. Following the experiment, the AEC fenced the contaminated area and returned control of the surrounding land to the DoD. Various radiological surveys have been performed in the area and in 2007, the DOE expanded the demarked contamination area by posting signs 200 to 400 feet (60 to 120 meters) outside of the original fence. Plutonium in soil is thought to attach preferentially to smaller particles. Therefore, redistribution of soil particulates by wind (dust) is the mechanism most likely to transport plutonium beyond the boundary of the Project 57 contamination area. In 2011, DRI installed two instrumentation towers to measure radiological, meteorological, and dust conditions. The monitoring activity was implemented to determine if radionuclide contamination was detectable in samples of airborne dust and characterize meteorological and environmental parameters that influence dust transport. Collected data also permits comparison of radiological conditions at the Project 57 monitoring stations to conditions observed at Community Environmental Monitoring Program (CEMP) stations around the NTTR. Biweekly samples of airborne particulates are submitted for laboratory

  10. Project Monitor: Part II. Conservation in small business: an exploratory study. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hammond, P Y

    1979-08-01

    Project Monitor examined the energy conservation attitude and behavior of small samples of small business owners/operators in Allegheny County, Pennsylvania, focusing on manufacturing concerns and retailers. Section I reports the findings on the energy conserving behavior of 92 smaller manufacturers and Section II identifies the factors which affect decision making concerning energy consuming activities by the owners/operators of 94 small retail establishments. In each, the impact of Project Pacesetter and of the coal strike and the general energy situation is considered. (MCW)

  11. REDD+ readiness: early insights on monitoring, reporting and verification systems of project developers

    Science.gov (United States)

    Joseph, Shijo; Herold, Martin; Sunderlin, William D.; Verchot, Louis V.

    2013-09-01

    A functional measuring, monitoring, reporting and verification (MRV) system is essential to assess the additionality and impact on forest carbon in REDD+ (reducing emissions from deforestation and degradation) projects. This study assesses the MRV capacity and readiness of project developers at 20 REDD+ projects in Brazil, Peru, Cameroon, Tanzania, Indonesia and Vietnam, using a questionnaire survey and field visits. Nineteen performance criteria with 76 indicators were formulated in three categories, and capacity was measured with respect to each category. Of the 20 projects, 11 were found to have very high or high overall MRV capacity and readiness. At the regional level, capacity and readiness tended to be highest in the projects in Brazil and Peru and somewhat lower in Cameroon, Tanzania, Indonesia and Vietnam. Although the MRV capacities of half the projects are high, there are capacity deficiencies in other projects that are a source of concern. These are not only due to limitations in technical expertise, but can also be attributed to the slowness of international REDD+ policy formulation and the unclear path of development of the forest carbon market. Based on the study results, priorities for MRV development and increased investment in readiness are proposed.

  12. The monitoring evaluation, reporting and verification of climate change mitigation projects

    Energy Technology Data Exchange (ETDEWEB)

    Vine, E.; Sathaye, J.

    1998-05-01

    Because of concerns with the growing threat of global climate change from increasing emissions of greenhouse gases, the US and other countries are implementing, by themselves or in cooperation with one or more other nations, climate change mitigation projects. These projects will reduce greenhouse gas (GHG) emissions or sequester carbon, and will also result in non-GHG benefits (i.e., environmental, economic, and social benefits). Monitoring, evaluating, reporting, and verifying (MERV) guidelines are needed for these projects to accurately determine their net GHG, and other, benefits. Implementation of MERV guidelines is also intended to: (1) increase the reliability of data for estimating GHG benefits; (2) provide real-time data so that mid-course corrections can be made; (3) introduce consistency and transparency across project types and reporters; and (4) enhance the credibility of the projects with stakeholders. In this paper, the authors review the issues involved in MERV activities. They identify several topics that future protocols and guidelines need to address, such as: (1) establishing a credible baseline; (2) accounting for impacts outside project boundaries through leakage; (3) net GHG reductions and other benefits; (4) precision of measurement; (5) MERV frequency; (6) persistence (sustainability) of savings, emissions reduction, and carbon sequestration; (7) reporting by multiple project participants; (8) verification of GHG reduction credits; (9) uncertainty and risk; (10) institutional capacity in conducting MERV; and (11) the cost of MERV.

  13. Monitoring Disinfection Byproduct Forming Potential with Simultaneous Absorbance Spectra and Fluorescence Excitation-Emission Mapping: Supporting Stage 2 EPA Regulation Monitoring Compliance

    Science.gov (United States)

    Gilmore, A. M.

    2011-12-01

    Water treatment plants in the United States will soon (by 2013 to 2013) be required to initialize enhanced monitoring for reducing disinfection by-products (DBPs) to meet the Stage 2 levels enforced by the EPA. The key to successfully meeting these requirements lies in the treatment plant's ability to deal with often dramatic source-water variations in natural organic matter (NOM) content. Whereas the regulated levels of NOM must be determined by measuring total organic carbon (TOC) often this parameter does not provide rapid or cost-effective qualitative or quantitative assessment of the various humic, fulvic and other aromatic NOM components. However, 2 main optical techniques namely UV absorbance and fluorescence excitation-emission mapping can be used for rapid assessment with precise identification of humic and fulvic components. This study presents data from a new type of instrument which simultaneously measures the UV-VIS absorbance spectrum and EEM. The rapid absorbance-EEM is facilitated by a single system that is more than 100 time faster than conventional scanning absorbance and fluoresence optical benches. The new system can continuously collect EEMs and absorbance spectra at a rate often greater than 1 per min with the extra capacity to monitor the UV254 absorbance and fluorescence emission spectrum excited at 254 nm in 4 ms intervals (an equivalent scan rate of 5.5 million nm/min). The EEM spectral data is corrected for all instrumental response factors including concentration dependent inner-filter effects. The accumulated EEM data sets can be modeled using conventional peak identification, PARAFAC and or PCA analysis of the fractionated samples to predict the trihalomethane forming potential (THMFP). This study compares the effectiveness of THFMP predictive models based on these three techniques and explains how these can be readily employed to facilitate the Stage 2 regulation compliance for DBP monitoring.

  14. Getting Closer, Empathising and Understanding: Setting the Stage for a Co-design Project with People with Dementia

    Directory of Open Access Journals (Sweden)

    Rita Maldonado Branco

    2015-10-01

    Full Text Available This paper discusses the initial work of a doctoral research project that explores how communication design can enable people with dementia and their social circle to codesign strategies to communicate. The ethnographic exercise in two care institutions and a consequent design intervention are described, and its process deconstructed: approaching institutions and participants, developing empathy and understanding towards configuring participation, and defining next stages of research. This study draws from approaches related to Design Anthropology and Participatory Design, which are intertwined and mutually influential, reinforcing their importance in developing a design project for and with people.

  15. DELIVERING TIMELY AIR QUALITY, TRAFFIC, AND WEATHER INFORMATION TO YOUR COMMUNITY/THE PASO DEL NORTE ENVIRONMENTAL MONITORING PROJECT

    Science.gov (United States)

    EPA has developed a technology transfer handbook for the EMPACT Paso del Norte Project. The EMPACT Paso del Norte Environmental Monitoring Project is a mobile vehicle emissions project that involves the international community of El Paso, TX; Sundland Park, NM; and Juarez, Mexico...

  16. Power monitoring and control for large scale projects: SKA, a case study

    Science.gov (United States)

    Barbosa, Domingos; Barraca, João. Paulo; Maia, Dalmiro; Carvalho, Bruno; Vieira, Jorge; Swart, Paul; Le Roux, Gerhard; Natarajan, Swaminathan; van Ardenne, Arnold; Seca, Luis

    2016-07-01

    Large sensor-based science infrastructures for radio astronomy like the SKA will be among the most intensive datadriven projects in the world, facing very high demanding computation, storage, management, and above all power demands. The geographically wide distribution of the SKA and its associated processing requirements in the form of tailored High Performance Computing (HPC) facilities, require a Greener approach towards the Information and Communications Technologies (ICT) adopted for the data processing to enable operational compliance to potentially strict power budgets. Addressing the reduction of electricity costs, improve system power monitoring and the generation and management of electricity at system level is paramount to avoid future inefficiencies and higher costs and enable fulfillments of Key Science Cases. Here we outline major characteristics and innovation approaches to address power efficiency and long-term power sustainability for radio astronomy projects, focusing on Green ICT for science and Smart power monitoring and control.

  17. Somebody is Watching EFL Classroom: A project on Improving Students’ Performance Level with a Monitoring System

    Directory of Open Access Journals (Sweden)

    Suna Akalın

    2011-04-01

    Full Text Available This study aims to explain a project on supporting students‟ speaking skills with a monitoring system. The monitoring system is aimed at controlling the usage of English continually in the afternoons, in weekdays, at a room which is being controlled by cameras. The absence of a teacher in the room is more comfortable than the cameras watching. This is a report of the Project implemented in the Department of teaching English, Ataturk University, Erzurum, Turkey. This study was conducted to find out how the usage of English in actual life situations contributes to learners‟ ability to develop their speaking abilities. The results revealed that learners‟ teacher‟s absence anxiety, instructor‟s attitude toward the speech room, course flexibility in the speech room, course quality, perceived usefulness and perceived ease of use, are the critical factors affecting learners‟ perceived satisfaction.

  18. Detection of gaps in the spatial coverage of coral reef monitoring projects in the US Caribbean and Gulf of Mexico.

    Science.gov (United States)

    Asch, R G; Turgeon, D D

    2003-06-01

    As part of the US Coral Reef Task Force's National Program to Map, Assess, Inventory, and Monitor US Coral Reef Ecosystems, a comprehensive survey of projects/programs monitoring coral reef ecosystems and related habitats (i.e., seagrass beds and mangroves) in the US Caribbean and Pacific was undertaken. Information was gathered on a total of 296 monitoring and assessment projects conducted since 1990 in the US Caribbean and the Gulf of Mexico. Substantial gaps in monitoring coverage of US coral reef ecosystems were revealed through geographic information system (GIS) analysis of survey metadata. Although southern Florida contains approximately two-thirds of all marine monitoring projects found in the US Caribbean and Gulf of Mexico, we were unable to identify any ongoing projects that monitor coral reefs along Florida's western coast and off of the Florida Middle Grounds. Additionally, Florida is covered by approximately 1 900 km2 of mangroves, yet there were only four ongoing projects that monitor this ecosystem, leaving gaps in coverage in the Lower and Middle Keys and along the eastern and western coasts. The Flower Garden Banks National Marine Sanctuary, located offshore of the Texas/Louisiana border, has an integral long-term monitoring program, but lacks a monitoring project that gathers long-term, quantitative data on reef lish abundance and certain water quality parameters. Numerous coral reef monitoring projects in Puerto Rico are concentrated on the island's southwestern coast surrounding La Parguera, while far fewer monitoring projects are conducted along the northern and southeastern coasts and around Vieques Island. In the US Virgin Islands, the paucity of monitoring projects in large areas of St. Croix and St. Thomas contrasts with monitoring activity in three marine protected areas (MPAs), where 66% of the US Virgin Islands' coral reef monitoring sites were found. Only a series of assessments have been conducted at Navassa, a small, uninhabited

  19. Sandia National Laboratories, California Quality Assurance Project Plan for Environmental Monitoring Program.

    Energy Technology Data Exchange (ETDEWEB)

    Holland, Robert C.

    2005-09-01

    This Quality Assurance Project Plan (QAPP) applies to the Environmental Monitoring Program at the Sandia National Laboratories/California. This QAPP follows DOE Quality Assurance Management System Guide for Use with 10 CFR 830 Subpart A, Quality Assurance Requirements, and DOE O 414.1C, Quality Assurance (DOE G 414.1-2A June 17, 2005). The Environmental Monitoring Program is located within the Environmental Operations Department. The Environmental Operations Department is responsible for ensuring that SNL/CA operations have minimal impact on the environment. The Department provides guidance to line organizations to help them comply with applicable environmental regulations and DOE orders. To fulfill its mission, the department has groups responsible for waste management; pollution prevention, air quality; environmental planning; hazardous materials management; and environmental monitoring. The Environmental Monitoring Program is responsible for ensuring that SNL/CA complies with all Federal, State, and local regulations and with DOE orders regarding the quality of wastewater and stormwater discharges. The Program monitors these discharges both visually and through effluent sampling. The Program ensures that activities at the SNL/CA site do not negatively impact the quality of surface waters in the vicinity, or those of the San Francisco Bay. The Program verifies that wastewater and stormwater discharges are in compliance with established standards and requirements. The Program is also responsible for compliance with groundwater monitoring, and underground and above ground storage tanks regulatory compliance. The Program prepares numerous reports, plans, permit applications, and other documents that demonstrate compliance.

  20. Automated chemical monitoring in new projects of nuclear power plant units

    Science.gov (United States)

    Lobanok, O. I.; Fedoseev, M. V.

    2013-07-01

    The development of automated chemical monitoring systems in nuclear power plant units for the past 30 years is briefly described. The modern level of facilities used to support the operation of automated chemical monitoring systems in Russia and abroad is shown. Hardware solutions suggested by the All-Russia Institute for Nuclear Power Plant Operation (which is the General Designer of automated process control systems for power units used in the AES-2006 and VVER-TOI Projects) are presented, including the structure of additional equipment for monitoring water chemistry (taking the Novovoronezh 2 nuclear power plant as an example). It is shown that the solutions proposed with respect to receiving and processing of input measurement signals and subsequent construction of standard control loops are unified in nature. Simultaneous receipt of information from different sources for ensuring that water chemistry is monitored in sufficient scope and with required promptness is one of the problems that have been solved successfully. It is pointed out that improved quality of automated chemical monitoring can be supported by organizing full engineering follow-up of the automated chemical monitoring system's equipment throughout its entire service life.

  1. Environmental monitoring for the DOE coolside and LIMB demonstration extension projects

    Energy Technology Data Exchange (ETDEWEB)

    White, T.; Contos, L.; Adams, L. (Radian Corp., Research Triangle Park, NC (United States). Progress Center)

    1992-02-01

    The purpose of this document is to present environmental monitoring data collected during the US DOE Limestone Injection Multistage Burner (LIMB) Demonstration Project Extension. The objective of the LIMB program is to demonstrate the sulfur dioxide (SO{sub 2}) and nitrogen oxide (NO{sub x}) emission reduction capabilities of the LIMB system. The LIMB system is a retrofit technology to be used for existing coal-fired boilers equipped with electrostatic precipitators. (VC)

  2. Near-surface monitoring for the ZERT shallow CO2 injection project

    Energy Technology Data Exchange (ETDEWEB)

    Strazisar, Brian R. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Wells, Arthur W. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Diehl, J. Rodney [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Hammack, Richard W. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Veloski, Garret A. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States)

    2009-12-01

    As part of a collaborative effort operated by the Zero Emission Research and Technology Center (ZERT), a series of two shallow releases of CO2 Was performed at a test site in Bozeman, MT. The purpose of the experiment was to simulate possible leakage scenarios from a carbon capture and storage operation in order to further develop and verify monitoring technologies used to characterize and quantify the release of CO2. The project included collaboration with several research groups and organizations. Presented here are the results of soil-gas monitoring conducted by researchers from the National Energy Technology Laboratory, including CO2 flux measurement, soil-gas analysis, perfluorocarbon tracer monitoring, and soil resistivity measurements. Together, these methods proved to be effective in detecting and characterizing leakage in the near-surface.

  3. 2008 Groundwater Monitoring Report Project Shoal Area, Corrective Action Unit 447

    Energy Technology Data Exchange (ETDEWEB)

    None

    2009-03-01

    This report presents the 2008 groundwater monitoring results collected by the U.S. Department of Energy (DOE) Office of Legacy Management (LM) at the Project Shoal Area (PSA) Subsurface Corrective Action Unit (CAU) 447 located in Churchill County, Nevada. Responsibility for the environmental site restoration of the PSA was transferred from the DOE Office of Environmental Management to LM on October 1, 2006. The environmental restoration process and corrective action strategy for CAU 447 are conducted in accordance with the Federal Facility Agreement and Consent Order (FFACO 1996, as amended February 2008) entered into by DOE, the U.S. Department of Defense, and the State of Nevada. The corrective action strategy for the site includes proof of concept monitoring in support of site closure. This report summarizes investigation activities associated with CAU 447 that were conducted at the site during 2008. This is the second groundwater monitoring report prepared by LM for the PSA

  4. The Project Monitoring and Early Warning System of Mould and Die

    Institute of Scientific and Technical Information of China (English)

    WANG Zongzhong; WANG Yi; CHEN Qingxin; MAO Ning

    2006-01-01

    The article simply describes the difficulties of the Mould and Die project control, and then put forward the thoughts of developing the Monitoring and Early Warning System for the Mould and Die manufacturing. Afterwards, the main three constructing principles and the goals of the system are explained carefully. Based on those, the theory and the classifications of the Monitoring and Early Warning are expounded. With the assistance of the use case diagram of UML (the United Modeling Language), the main functions of the system are analyzed; and with the activity diagram of the UML, the work flows of the monitoring and early warning are expressed clearly. Finally, the classes and the architectures of the system are designed by making use of the class diagram of UML.

  5. 2010 Groundwater Monitoring Report Project Shoal Area, Corrective Action Unit 447

    Energy Technology Data Exchange (ETDEWEB)

    None

    2011-02-01

    This report presents the 2010 groundwater monitoring results collected by the U.S. Department of Energy (DOE) Office of Legacy Management (LM) at the Project Shoal Area (PSA) Subsurface Corrective Action Unit (CAU) 447 in Churchill County, Nevada. Responsibility for the environmental site restoration of the PSA was transferred from the DOE Office of Environmental Management to LM on October 1, 2006. The environmental restoration process and corrective action strategy for CAU 447 are conducted in accordance with the Federal Facility Agreement and Consent Order (FFACO 1996, as amended March 2010) entered into by DOE, the U.S. Department of Defense, and the State of Nevada. The corrective action strategy for the site includes monitoring in support of site closure. This report summarizes the results from the groundwater monitoring program during fiscal year 2010.

  6. Monitoring and Evaluation : Yakima/Klickitat Fisheries Project, Final Report 2000.

    Energy Technology Data Exchange (ETDEWEB)

    Sampson, Melvin R.

    2000-01-01

    The monitoring and evaluation objectives and tasks have been developed through a joint process between the co-managers, Yakama Nation (YN, Lead Agency) and Washington Department of Fish and Wildlife (WDFW). The Science/Technical Advisory Committee (STAC), which consists of core members from the co-managers, employs the services of a work committee of scientists, the Monitoring Implementation Planning Team (MIPT) to develop the Monitoring and Evaluation (M&E) Plan. The process employed by STAC to verify these designated activities and the timing of their implementation involved the utilization of the following principles: (1) YKFP monitoring should evaluate the success (or lack of it) of project supplementation efforts and its impacts, including juvenile post release survival, natural production and reproductive success, ecological interactions, and genetics; (2) YKFP monitoring should be comprehensive: and, (3) YKFP monitoring should be done in such a way that results are of use to salmon production efforts throughout and Columbia basin and the region. Utilizing these principles, STAC and MIPT developed this M&E action plan in three phases. The first phase was primarily conceptual. STAC and MIPT defined critical issues and problems and identified associated response variables. The second phase was quantitative, which determined the scale and size of an effective monitoring effort. A critical element of the quantitative phase was an assessment of the precision with which response variables can be measured, the probability of detecting real impacts and the sample sizes required for a given level of statistical precision and power. The third phase is logistical. The feasibility of monitoring measures was evaluated as to practicality and cost. The Policy Group has determined that the M&E activities covered by this agreement are necessary, effective and cost-efficient.

  7. Monitoring and Evaluation : Yakima/Klickitat Fisheries Project, Annual Report 2001.

    Energy Technology Data Exchange (ETDEWEB)

    Sampson, Melvin R.

    2002-12-01

    The monitoring and evaluation objectives and tasks have been developed through a joint process between the co-managers, Yakama Nation (YN, Lead Agency) and Washington Department of Fish and Wildlife (WDFW). The Science/Technical Advisory Committee (STAC), which consists of core members from the co-managers, employs the services of a work committee of scientists, the Monitoring Implementation Planning Team (MIPT) to develop the Monitoring and Evaluation (M&E) Plan. The process employed by STAC to verify these designated activities and the timing of their implementation involved the utilization of the following principles: (1) YKFP monitoring should evaluate the success (or lack of it) of project supplementation efforts and its impacts, including juvenile post release survival, natural production and reproductive success, ecological interactions, and genetics; (2) YKFP monitoring should be comprehensive: and, (3) YKFP monitoring should be done in such a way that results are of use to salmon production efforts throughout and Columbia basin and the region. Utilizing these principles, STAC and MIPT developed this M&E action plan in three phases. The first phase was primarily conceptual. STAC and MIPT defined critical issues and problems and identified associated response variables. The second phase was quantitative, which determined the scale and size of an effective monitoring effort. A critical element of the quantitative phase was an assessment of the precision with which response variables can be measured, the probability of detecting real impacts and the sample sizes required for a given level of statistical precision and power. The third phase is logistical. The feasibility of monitoring measures was evaluated as to practicality and cost. The Policy Group has determined that the M&E activities covered by this agreement are necessary, effective and cost-efficient.

  8. The Navruz Project: Transboundary Monitoring for Radionuclides and Metals in Central Asia Rivers. Data Report

    Energy Technology Data Exchange (ETDEWEB)

    Passell, Howard D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Barber, David S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Betsill, J. David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Littlefield, Adriane C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Mohagheghi, Amir H. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Shanks, Sonoya T. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Yuldashev, Bekhzad [Inst. of Nuclear Physics, Tashkent (Uzbekistan); Saalikhbaev, Umar [Inst. of Nuclear Physics, Tashkent (Uzbekistan); Radyuk, Raisa [Inst. of Nuclear Physics, Tashkent (Uzbekistan); Djuraev, Akram [Tajik Academy of Sciences, Dushanbe (Tajikistan); Djuraev, Anwar [Tajik Academy of Sciences, Dushanbe (Tajikistan); Vasilev, Ivan [Inst. of Physics, Bishkek (Kyrgyzstan); Tolongutov, Bajgabyl [Inst. of Physics, Bishkek (Kyrgyzstan); Valentina, Alekhina [Inst. of Physics, Bishkek (Kyrgyzstan); Solodukhin, Vladimir [Inst. of Nuclear Physics, Almaty (Kazakhstan); Pozniak, Victor [Inst. of Nuclear Physics, Almaty (Kazakhstan)

    2003-04-01

    The Navruz Project is a cooperative, transboundary, river monitoring project involving rivers and institutions in Kazakhstan, Kyrgyzstan, Tajikistan, and Uzbekistan, and facilitated by Sandia National Laboratories in the U.S. The Navruz Project focuses on waterborne radionuclides and metals because of their importance to public health and nuclear materials proliferation concerns in the region. The Project also collects data on basic water quality parameters. Data obtained in this project are shared among all participating countries and the public through a world-wide web site (http://www.cmc.sandia.org/Central/centralasia.html), and are available for use in further studies and in regional transboundary water resource management efforts. This report includes graphs showing selected data from the Fall 2000 and Spring 2001 sampling seasons. These data include all parameters grouped into six regions, including main rivers and some tributaries in the Amu Darya and Syr Darya river systems. This report also assembles all data (in tabular form) generated by the project from Fall 2000 through Fall 2001. This report comes as the second part of a planned three-part reporting process. The first report is the Sampling and Analysis Plan and Operational Manual, SAND 2002-0484. This is the second report.

  9. Results of the MITRA project: Monitoring and intervention for the transportation of dangerous goods

    Energy Technology Data Exchange (ETDEWEB)

    Planas, E. [Centre d' Estudis del Risc Tecnologic (CERTEC), Departament d' Enginyeria Quimica, Universitat Politecnica de Catalunya, Diagonal 647, 08028-Barcelona, Catalonia (Spain)], E-mail: eulalia.planas@upc.edu; Pastor, E. [Centre d' Estudis del Risc Tecnologic (CERTEC), Departament d' Enginyeria Quimica, Universitat Politecnica de Catalunya, Diagonal 647, 08028-Barcelona, Catalonia (Spain); Presutto, F. [M3 Systems, 1 Rue des Oiseaux, 31410 Lavernose (France); Tixier, J. [Ecole des Mines d' Ales, Ales (France)

    2008-04-01

    The objective of the MITRA (monitoring and intervention for the transportation of dangerous goods) project was to prototype a new operational system for monitoring the transportation of dangerous goods in Europe based on regional responsibilities. This concept, based on systems used in air traffic control, aims to provide civil security centres with real-time knowledge of the position and contents of dangerous vehicles circulating in their area of responsibility, and, in the event of a dangerous situation, to issue warnings, alerts and crisis management information, thereby allowing intervention teams to react immediately with maximum safety. The project was funded by the European Commission under the 6th Framework Programme (STREP - specific targeted research project - under the Information Society Technologies priority). It started on 1 September 2004 and ended on 31 October 2006. This paper presents the results of this project and the conclusions derived from the field tests carried out in Germany and in the French/Spanish border region in order to test the proposed operational system.

  10. Environmental monitoring for the DOE coolside and LIMB demonstration extension projects

    Energy Technology Data Exchange (ETDEWEB)

    White, T.; Contos, L.

    1991-09-01

    The purpose of this document is to present environmental monitoring data collected during the US Department of Energy Limestone Injection Multistage Burner (DOE LIMB) Demonstration Project Extension at the Ohio Edison Edgewater Generating Station in Lorain, Ohio. These data were collected by implementing the Environmental Monitoring Plan (EMP) for the DOE LIMB Demonstration Project Extension, dated August 1988. This document is the fifth EMP status report to be published and presents the data generated during November and December 1990, and January 1991. These reports review a three or four month period and have been published since the project's start in October 1989. The DOE project is an extension of the US Environmental Protection Agency's (EPA) original LIMB Demonstration. The program is operated under DOE's Clean Coal Technology Program of emerging clean coal technologies'' under the categories of in boiler control of oxides of sulfur and nitrogen'' as well as post-combustion clean-up.'' The objective of the LIMB program is to demonstrate the sulfur dioxide (SO{sub 2}) and nitrogen oxide (NO{sub x}) emission reduction capabilities of the LIMB system. The LIMB system is a retrofit technology to be used for existing coal-fired boilers equipped with electrostatic precipitators (ESPs). 5 figs., 12 tabs.

  11. The CHAIN-Project and Installation of Flare Monitoring Telescopes in Developing Countries

    Directory of Open Access Journals (Sweden)

    S UeNo

    2009-04-01

    Full Text Available The Flare Monitoring Telescope (FMT was constructed in 1992 at Hida Observatory in Japan to investigate the long-term variation of solar activity and explosive events. It has five solar imaging telescopes that simultaneously observe the full-disk Sun at different wavelengths around the H-alpha absorption line or in different modes. Therefore, the FMT can measure the three-dimensional velocity field of moving structures on the full solar disk. The science target of the FMT is to monitor solar flares and erupting filaments continuously all over the solar disk and to investigate correlation between the characteristics of the erupting phenomena and the geoeffectiveness of the corresponding coronal mass ejections (CMEs. We are planning to start up a new worldwide project, the Continuous H-alpha Imaging Network (CHAIN project, as an important IHY project of our observatories. As part of this project, we are examining the possibility of installing telescopes similar to the FMT in developing countries. We have selected Peru and Algeria as the countries where the first and second overseas FMTs will be installed, and we are aiming to start operation of these FMTs by the end of 2010 before the maximum phase of solar cycle 24. To create such an international network, it will be necessary to improve the information technologies applied in our observation-system. In this paper, we explain the current status and future areas of work regarding our system.

  12. Web based concept project for information and communication of monitoring policy and techniques

    Energy Technology Data Exchange (ETDEWEB)

    Levy, D. S.; Sordi, G. M. A. A., E-mail: info@uniprorad.com.br [Instituto de Pesquisas Energeticas e Nucleares / CNEN, Av. Lineu Prestes 2242, Cidade Universitaria, 05508-000 Sao Paulo (Brazil)

    2014-08-15

    Information and Communication Technology (ICT) is growing in Brazil and worldwide. The servers processing power added to the technology of relational databases allow to integrate information from different sources, enabling complex queries with reduced response time. We believe that the use of information technology for the radiological protection programs for human activities shall help greatly the radioactive facility that requires such use. Therefore, this project aims the informatization of the monitoring policy and techniques in Portuguese, providing Brazilian radioactive facilities a complete repository for research, consultation and information in a quick, integrated and efficient way. In order to meet national and international standards, the development of this project includes concepts, definitions and theory about monitoring procedures in order to interrelate information, currently scattered in several publications and documents, in a consistent and appropriate manner. The Web platform tools and functionalities were developed according to our target public needs, regarding new possibilities of media, like mobile access, feeds of content and information sharing. Moreover, taking into account this is a pioneer project with the prospect of long-term use, our challenge involves the combination of multiple computer technologies that allows a robust, effective, and flexible system, which can be easily adapted according to future technological innovations. This pioneer project shell help greatly both radioactive facilities and researchers, and it is our target to make it an international reference for Portuguese Spoken countries. (Author)

  13. What to be implemented at the early stage of a large-scale project

    CERN Document Server

    Bachy, Gérard; Bachy, Gerard; Hameri, Ari Pekka

    1997-01-01

    This paper addresses the importance of the actions to be taken before the project planning phases begin. The approach taken stems from the production planning paradigm, with emphasis on the product, rather than on the process. It is argued that a complete part list or product breakdown structure (PBS) is the absolute prerequisite for the design of a successful work breakdown structure (WBS) for a project. This process requires the definition of the design and configuration disciplines during the engineering phase. These critical issues of concurrent engineering and product development are also emphasized in the paper. The WBS is, in turn, needed to establish a suitable organizational breakdown structure (OBS or organigram) for the project. Finally, the assembly sequence and the related assembly breakdown structure (ABS) of the end product is required before commencing the project planning phase, which provides the schedules, resource allocation, progress control, and the like for the project management. Detai...

  14. NOFBX Single-Stage-to-Orbit Mars Ascent Vehicle Engine Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose the continuation of our research and development of a Nitrous Oxide Fuel Blend (NOFBXTM) Single-Stage-to-Orbit (SSTO) monopropellant propulsion system for...

  15. A High-Payload Fraction, Pump-Fed, 2-Stage Nano Launch Vehicle Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Ventions proposes the development of a pump-fed, 2-stage nano launch vehicle for low-cost on-demand placement of cube and nano-satellites into LEO. The proposed...

  16. A Two-Stage Waste Gasification Reactor for Mars In-Situ Resource Utilization Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to design, build, and test a two-stage waste processing reactor for space applications. Our proposed technology converts waste from space missions into...

  17. Synthetic control charts with two-stage sampling for monitoring bivariate processes

    Directory of Open Access Journals (Sweden)

    Antonio F. B. Costa

    2007-04-01

    Full Text Available In this article, we consider the synthetic control chart with two-stage sampling (SyTS chart to control bivariate processes. During the first stage, one item of the sample is inspected and two correlated quality characteristics (x;y are measured. If the Hotelling statistic T1² for these individual observations of (x;y is lower than a specified value UCL1 the sampling is interrupted. Otherwise, the sampling goes on to the second stage, where the remaining items are inspected and the Hotelling statistic T2² for the sample means of (x;y is computed. When the statistic T2² is larger than a specified value UCL2, the sample is classified as nonconforming. According to the synthetic control chart procedure, the signal is based on the number of conforming samples between two neighbor nonconforming samples. The proposed chart detects process disturbances faster than the bivariate charts with variable sample size and it is from the practical viewpoint more convenient to administer.Este artigo apresenta um gráfico de controle com regra especial de decisão e amostragens em dois estágios para o monitoramento de processos bivariados. No primeiro estágio, um item da amostra é inspecionado e duas características de qualidade correlacionadas (x;y são medidas. Se a estatística de Hotelling T1² para as observações individuais de (x;y for menor que um valor especificado UCL1 a amostragem é interrompida. Caso contrário, a amostragem segue para o segundo estágio, onde os demais itens da amostra são inspecionados e a estatística de Hotelling T2² para as médias de (x;y é calculada. Quando a estatística T2² é maior que um valor especificado UCL2, a amostra é classificada como não conforme. De acordo com a regra especial de decisão, o alarme é baseado no número de amostras entre duas não conformes. O gráfico proposto é mais ágil e mais simples do ponto de vista operacional que o gráfico de controle bivariado com tamanho de amostras variável.

  18. Acoustic Monitoring of Beluga Whale Interactions with Cook Inlet Tidal Energy Project

    Energy Technology Data Exchange (ETDEWEB)

    Worthington, Monty [Project Director - AK

    2014-02-05

    Cook Inlet, Alaska is home to some of the greatest tidal energy resources in the U.S., as well as an endangered population of beluga whales (Delphinapterus leucas). Successfully permitting and operating a tidal power project in Cook Inlet requires a biological assessment of the potential and realized effects of the physical presence and sound footprint of tidal turbines on the distribution, relative abundance, and behavior of Cook Inlet beluga whales. ORPC Alaska, working with the Project Team—LGL Alaska Research Associates, University of Alaska Anchorage, TerraSond, and Greeneridge Science—undertook the following U.S. Department of Energy (DOE) study to characterize beluga whales in Cook Inlet – Acoustic Monitoring of Beluga Whale Interactions with the Cook Inlet Tidal Energy Project (Project). ORPC Alaska, LLC, is a wholly-owned subsidiary of Ocean Renewable Power Company, LLC, (collectively, ORPC). ORPC is a global leader in the development of hydrokinetic power systems and eco-conscious projects that harness the power of ocean and river currents to create clean, predictable renewable energy. ORPC is developing a tidal energy demonstration project in Cook Inlet at East Foreland where ORPC has a Federal Energy Regulatory Commission (FERC) preliminary permit (P-13821). The Project collected baseline data to characterize pre-deployment patterns of marine mammal distribution, relative abundance, and behavior in ORPC’s proposed deployment area at East Foreland. ORPC also completed work near Fire Island where ORPC held a FERC preliminary permit (P-12679) until March 6, 2013. Passive hydroacoustic devices (previously utilized with bowhead whales in the Beaufort Sea) were adapted for study of beluga whales to determine the relative abundance of beluga whale vocalizations within the proposed deployment areas. Hydroacoustic data collected during the Project were used to characterize the ambient acoustic environment of the project site pre-deployment to inform the

  19. Three-year monitoring of serum p53 antibody during chemotherapy and surgery for stage IV rectal cancer.

    Science.gov (United States)

    Suzuki, Takayuki; Shimada, Hideaki; Ushigome, Mitsunori; Koike, Junichi; Funahashi, Kimihiko; Nemoto, Tetsuo; Kaneko, Hironori

    2016-04-01

    The overexpression of mutant p53 stimulates serum p53 antibody production in patients with colorectal carcinoma even in superficial tumors. Although the short-term perioperative monitoring of serum p53 antibody titers is reported to be useful in predicting tumor recurrence and patient survival in colorectal carcinoma, the clinical utility of the long-term monitoring of serum p53 antibody titers in patients with colorectal cancer remains unknown. Here, we report the 3-year monitoring of serum p53 antibody titers in a 60-year-old man with rectal cancer, clinical stage IV (T2N2M1b, lung and liver metastases), who was treated with chemotherapy and surgery. Screening tests for CEA (29.4 ng/ml), CA19-9 (41.1 U/ml), and serum p53 antibody (2170 U/ml) were positive before treatment. After chemotherapy with mFOLFOX6 + bevacizumab (B-mab), CEA and CA19-9 decreased to the normal range. However, serum p53 antibody titer remained positive (283 U/ml). After low anterior resection, the serum p53 antibody titer still remained positive (63.4 U/ml). Serum p53 antibody titer significantly changed and was associated with treatment response and tumor recurrence. In the last 6 months of the patient's life, serum p53 antibody titer gradually decreased, which possibly reflects the modification of the patient's immune response to p53 antigens.

  20. Implementation of quality management in early stages of research and development projects at a university.

    Science.gov (United States)

    Fiehe, Sandra; Wagner, Georg; Schlanstein, Peter; Rosefort, Christiane; Kopp, Rüdger; Bensberg, Ralf; Knipp, Peter; Schmitz-Rode, Thomas; Steinseifer, Ulrich; Arens, Jutta

    2014-04-01

    The ultimate objective of university research and development projects is usually to create knowledge, but also to successfully transfer results to industry for subsequent marketing. We hypothesized that the university technology transfer requires efficient measures to improve this important step. Besides good scientific practice, foresighted and industry-specific adapted documentation of research processes in terms of a quality management system might improve the technology transfer. In order to bridge the gap between research institute and cooperating industry, a model project has been accompanied by a project specific amount of quality management. However, such a system had to remain manageable and must not constrain the researchers' creativity. Moreover, topics and research team are strongly interdisciplinary, which entails difficulties regarding communication because of different perspectives and terminology. In parallel to the technical work of the model project, an adaptable quality management system with a quality manual, defined procedures, and forms and documents accompanying the research, development and validation was implemented. After process acquisition and analysis the appropriate amount of management for the model project was identified by a self-developed rating system considering project characteristics like size, innovation, stakeholders, interdisciplinarity, etc. Employees were trained according to their needs. The management was supported and the technical documentation was optimized. Finally, the quality management system has been transferred successfully to further projects.

  1. Yakima/Klickitat Fisheries Project - Klickitat Monitoring and Evaluation, 2007 Annual Report.

    Energy Technology Data Exchange (ETDEWEB)

    Zendt, Joe; Babcock, Mike [Yakama Nation Fisheries Resource Management

    2006-04-02

    This report describes the results of monitoring and evaluation (M&E) activities for salmonid fish populations and habitat in the Klickitat River subbasin in south-central Washington. The M&E activities described here were conducted as a part of the Bonneville Power Administration (BPA)-funded Yakima/Klickitat Fisheries Project (YKFP) and were designed by consensus of the scientists with the Yakama Nation (YN) Fisheries Program. YKFP is a joint project between YN and Washington Department of Fish and Wildlife (WDFW). Overall YKFP goals are to increase natural production of and opportunity to harvest salmon and steelhead in the Yakima and Klickitat subbasins using hatchery supplementation, harvest augmentation and habitat improvements. Klickitat subbasin M&E activities have been subjected to scientific and technical review by members of the YKFP Science/Technical Advisory Committee (STAC) as part of the YKFP's overall M&E proposal. Yakama Nation YKFP biologists have transformed the conceptual design into the tasks described. YKFP biologists have also been involved with the Collaborative Systemwide Monitoring and Evaluation Project (CSMEP - a project aimed at improving the quality, consistency, and focus of fish population and habitat data to answer key M&E questions relevant to major decisions in the Columbia Basin) and are working towards keeping Klickitat M&E activities consistent with CSMEP recommendations. This report summarizes progress and results for the following major categories of YN-managed tasks under this contract: (1) Monitoring and Evaluation - to gather baseline information in order to characterize habitat and salmonid populations pre- and post-habitat restoration and pre-supplementation. (2) Ecological Interactions - to determine presence of pathogens in wild and naturally produced salmonids in the Klickitat Basin and develop supplementation strategies using this information. (3) Genetics - to develop YKFP supplementation broodstock collection

  2. Robotic Asteroid Prospector (RAP) Staged from L-1: Start of the Deep Space Economy Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objectives of the Robotic Asteroid Prospector (RAP) project are to examine and evaluate the feasibility of asteroid mining in terms of means, methods, and...

  3. Evaluation of 18-F-fluoro-2-deoxyglucose (FDG) positron emission tomography/computed tomography (PET/CT) as a staging and monitoring tool for dogs with stage-2 splenic hemangiosarcoma – A pilot study

    Science.gov (United States)

    Winter, Amber L.; Stuebner, Kathleen; Scott, Ruth; Ober, Christopher P.; Anderson, Kari L.; Feeney, Daniel A.; Vallera, Daniel A.; Koopmeiners, Joseph S.; Modiano, Jaime F.; Froelich, Jerry

    2017-01-01

    Positron Emission Tomography-Computed Tomography (PET-CT) is routinely used for staging and monitoring of human cancer patients and is becoming increasingly available in veterinary medicine. In this study, 18-fluorodeoxyglucose (18FDG)-PET-CT was used in dogs with naturally occurring splenic hemangiosarcoma (HSA) to assess its utility as a staging and monitoring modality as compared to standard radiography and ultrasonography. Nine dogs with stage-2 HSA underwent 18FDG-PET-CT following splenectomy and prior to commencement of chemotherapy. Routine staging (thoracic radiography and abdominal ultrasonography) was performed prior to 18FDG-PET-CT in all dogs. When abnormalities not identified on routine tests were noted on 18FDG-PET-CT, owners were given the option to repeat a PET-CT following treatment with eBAT. A PET-CT scan was repeated on Day 21 in three dogs. Abnormalities not observed on conventional staging tools, and most consistent with malignant disease based on location, appearance, and outcome, were detected in two dogs and included a right atrial mass and a hepatic nodule, respectively. These lesions were larger and had higher metabolic activity on the second scans. 18FDG-PET-CT has potential to provide important prognostic information and influence treatment recommendations for dogs with stage-2 HSA. Additional studies will be needed to precisely define the value of this imaging tool for staging and therapy monitoring in dogs with this and other cancers. PMID:28222142

  4. Decision-making in the Pre-design Stage of Sustainable Building Renovation Projects

    DEFF Research Database (Denmark)

    Nielsen, Anne Nørkjær; Steen Larsen, Tine; Jensen, Rasmus Lund

    2017-01-01

    There is a great potential in renovating our existing building stock, in terms of improving environmental, economic and social qualities. Meeting the increasing performance requirements for sustainable construction entails an increasing level of complexity in the design process of both new...... assessment scheme (e.g. DGNB-DK), or project specific sustainability criteria. The results presented in this paper are a part of an ongoing research project focusing on developing a new decision support tool for sustainable renovation....

  5. Sustainable Seas Student Intertidal Monitoring Project at Duxbury Reef in Bolinas, CA

    Science.gov (United States)

    Rainsford, A.; Soave, K.; Gerraty, F.; Jung, G.; Quirke-Shattuck, M.; Kudler, J.; Hatfield, J.; Emunah, M.; Dean, A. F.

    2014-12-01

    The Sustainable Seas Student Monitoring Project at the Branson School in Ross, CA has monitored Duxbury Reef in Bolinas, CA since 1999, in cooperation with the Farallones Marine Sanctuary Association and the Gulf of Farallones National Marine Sanctuary. Goals of this student-run project include: 1) To monitor the rocky intertidal habitat and develop a baseline database of invertebrates and algal density and abundance; 2) To contribute to the conservation of the rocky intertidal habitat through education of students and visitors about intertidal species; 3) To increase stewardship in the Gulf of the Farallones National Marine Sanctuary; and 4) To contribute abundance and population data on key algae and invertebrate species to the national database, LiMPETS (Long Term Monitoring Program & Experiential Training for Students). Each fall student volunteers complete an intensive training course on the natural history of intertidal invertebrates and algae, identification of key species, rocky intertidal monitoring techniques, and history of the sanctuary. Students identify and count key invertebrate and algae species along two permanent transects and, using randomly determined points, within two permanent 200 m2 areas, in fall, winter, and late spring. Using data from the previous years, we will compare population densities, seasonal abundance and long-term population trends of key algal and invertebrate species, including Tegula funebralis, Anthopluera elegantissima, Cladophora sp. and Fucus sp.. Future analyses and investigations will include intertidal abiotic factors (including water temperature, pH and human foot-traffic) to enhance insights into the Duxbury Reef ecosystem, in particular, the high and mid-intertidal zones experiencing the greatest amount of human impacts.

  6. A guide to environmental monitoring data, 1945--1972: Hanford Environmental Dose Reconstruction Project

    Energy Technology Data Exchange (ETDEWEB)

    Thiede, M.E.; Bates, D.J.; Mart, E.I.; Hanf, R.W.

    1994-03-01

    This report is a guide to the work accomplished by the Environmental Monitoring Data Task, which is one of the tasks in the Hanford Environmental Dose Reconstruction (HEDR) Project. The objective of the Environmental Monitoring Data Task was to recover, evaluate, process, and/or reconstruct the environmental monitoring data for the period 1945--1972. The period of time for which environmental monitoring data were sought was determined by the start-up and shut-down dates of the Hanford facilities that emitted the majority of radionuclides to the two major pathways: air and the Columbia River. Radionuclide emissions to the air were mainly the result of the operation of the chemical separations plants from 1944--1972 (Heeb 1994). Radionuclide emissions to the Columbia River were mainly the result of the operation of the single-pass production reactors from 1944--1971 (Heeb and Bates 1994). Therefore, the historical environmental monitoring data sought were for the period 1945--1972. Within the period of 1945--1972, specific periods of interest to the HEDR Project vary depending on the pathway. For example, 1945--1951 was the peak period for radionuclide emissions to the air and hence vegetation uptake of radionuclides, while 1956--1965 was the peak period for radionuclide emissions to the Columbia River and hence fish uptake of radionuclides. However, adequate historical data were not always available for the periods of interest. In the case of vegetation measurements, conversion and correction factors had to be developed to convert the historical measurements to modern standard measurements. Table S.1 lists the reports that explain these conversion and correction factors. In the case of Columbia River fish and waterfowl, bioconcentration factors were developed for use in any year where the river pathway data are insufficient.

  7. Fish Research Project Oregon; Umatilla Hatchery Monitoring and Evaluation, 1993-1994 Annual Report.

    Energy Technology Data Exchange (ETDEWEB)

    Hayes, Michael C.; Onjukka, Sam T.; Focher, Shannon M. (Oregon Department of Fish and Wildlife, Portland, OR)

    1995-01-01

    This report covers the first three years of comprehensive monitoring and evaluation of the Umatilla Hatchery. Because the hatchery and the evaluation study and the fish health monitoring investigations are in the early stages of implementation, much of the information contained in this report is preliminary. The majority of the data that is crucial for evaluating the success of the hatchery program, the data on post-release performance and survival, is yet unavailable. In addition, several years of data are necessary to make conclusions about rearing performance at Umatilla Hatchery. The conclusions drawn in this report should be viewed as preliminary and should be used in conjunction with additional information as it becomes available.

  8. Sustainable Seas Student Intertidal Monitoring Project at Duxbury Reef in Bolinas, CA (Invited)

    Science.gov (United States)

    Soave, K.; Dean, A.; Darakananda, K.; Ball, O.; Butti, C.; Yang, G.; Vetter, M.; Grimaldi, Z.

    2009-12-01

    Sustainable Seas Student Intertidal Monitoring Project at Duxbury Reef in Bolinas, CA Kathy Soave, Amy Dean, Olivia Ball, Karin Darakananda, Matt Vetter, Grant Yang, Charlotte Butti, Zoe Grimaldi The Sustainable Seas Student Monitoring Project at the Branson School in Ross, CA has monitored Duxbury Reef in Bolinas, CA since 1999, in cooperation with the Farallones Marine Sanctuary Association and the Gulf of Farallones National Marine Sanctuary. Goals of the project include: 1) To monitor the rocky intertidal habitat and develop a baseline database of invertebrates and algal density and abundance; 2) To contribute to the conservation of the rocky intertidal habitat through education of students and visitors about intertidal species and the requirements for maintaining a healthy, diverse intertidal ecosystem; 3) To increase stewardship in the Gulf of the Farallones National Marine Sanctuary; and 4) To contribute abundance and population data on key algae and invertebrate species to the national database, LiMPETS (Long Term Monitoring Program & Experiential Training for Students). Student volunteers complete an intensive training course on the natural history of intertidal invertebrates and algae, identification of key species, rocky intertidal monitoring techniques, and history of the sanctuary. Students identify and count key invertebrate and algae species along two permanent transects (A and B) and using randomly determined points within a permanent 100 m2 area, three times per year (fall, winter, and late spring). Using the data collected since 2004, we will analyze the population densities, seasonal abundance and long-term population trends of key algal and invertebrate species. Future analyses and investigations will include intertidal abiotic factors (including water temperature and human foot-traffic) to enhance insights into the workings of the Duxbury Reef ecosystem, in particular, the high intertidal zone which experiences the greatest amount of human

  9. Miniaturized, Multi-Analyte Sensor Array for the Automated Monitoring of Major Atmospheric Constituents in Spacecraft Environment Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of the Phase II SBIR project is to develop a prototype sensor system to detect gaseous analytes in support of the spacecraft environmental monitoring...

  10. Science advancements key to increasing management value of life stage monitoring networks for endangered Sacramento River winter-run Chinook salmon in California

    Science.gov (United States)

    Johnson, Rachel C.; Windell, Sean; Brandes, Patricia L.; Conrad, J. Louise; Ferguson, John; Goertler, Pascale A. L.; Harvey, Brett N.; Heublein, Joseph; Isreal, Joshua A.; Kratville, Daniel W.; Kirsch, Joseph E.; Perry, Russell W.; Pisciotto, Joseph; Poytress, William R.; Reece, Kevin; Swart, Brycen G.

    2017-01-01

    A robust monitoring network that provides quantitative information about the status of imperiled species at key life stages and geographic locations over time is fundamental for sustainable management of fisheries resources. For anadromous species, management actions in one geographic domain can substantially affect abundance of subsequent life stages that span broad geographic regions. Quantitative metrics (e.g., abundance, movement, survival, life history diversity, and condition) at multiple life stages are needed to inform how management actions (e.g., hatcheries, harvest, hydrology, and habitat restoration) influence salmon population dynamics. The existing monitoring network for endangered Sacramento River winterrun Chinook Salmon (SRWRC, Oncorhynchus tshawytscha) in California’s Central Valley was compared to conceptual models developed for each life stage and geographic region of the life cycle to identify relevant SRWRC metrics. We concluded that the current monitoring network was insufficient to diagnose when (life stage) and where (geographic domain) chronic or episodic reductions in SRWRC cohorts occur, precluding within- and among-year comparisons. The strongest quantitative data exist in the Upper Sacramento River, where abundance estimates are generated for adult spawners and emigrating juveniles. However, once SRWRC leave the upper river, our knowledge of their identity, abundance, and condition diminishes, despite the juvenile monitoring enterprise. We identified six system-wide recommended actions to strengthen the value of data generated from the existing monitoring network to assess resource management actions: (1) incorporate genetic run identification; (2) develop juvenile abundance estimates; (3) collect data for life history diversity metrics at multiple life stages; (4) expand and enhance real-time fish survival and movement monitoring; (5) collect fish condition data; and (6) provide timely public access to monitoring data in open data

  11. Using drift nets to capture early life stages and monitor spawning of the yangtze river chinese sturgeon (Acipenser sinensis)

    Science.gov (United States)

    Wei, Q.W.; Kynard, B.; Yang, D.G.; Chen, X.H.; Du, H.; Shen, L.; Zhang, H.

    2009-01-01

    A sampling system for capturing sturgeon eggs using a D-shaped bottom anchored drift net was used to capture early life stages (ELS) of Chinese sturgeon, Acipenser sinensis, and monitor annual spawning success at Yichang on the Yangtze River, 1996-2004, before and just after the Three Gorges Dam began operation. Captured were 96 875 ELS (early life stages: eggs, yolk-sac larvae = eleuthero embryos, and larvae); most were eggs and only 2477 were yolk-sac larvae. Most ELS were captured in the main river channel and inside the bend at the Yichang spawning reach. Yolk-sac larvae were captured for a maximum of 3 days after hatching began, indicating quick dispersal downstream. The back-calculated day of egg fertilization over the eight years indicated a maximum spawning window of 23 days (20 October-10 November). Spawning in all years was restricted temporally, occurred mostly at night and during one or two spawning periods, each lasting several days. The brief temporal spawning window may reduce egg predation by opportunistic predators by flooding the river bottom with millions of eggs. During 1996-2002, the percentage of fertilized eggs in an annual 20-egg sample was between 63.5 to 94.1%; however, in 2003 the percentage fertilized was only 23.8%. This sudden decline may be related to the altered environmental conditions at Yichang caused by operation of the Three Gorges Dam. Further studies are needed to monitor spawning and changes in egg fertilization in this threatened population. ?? 2009 Blackwell Verlag GmbH.

  12. [Monitoring populations of rodent reservoirs of zoonotic diseases. Projects, aims and results].

    Science.gov (United States)

    Jacob, J; Ulrich, R G; Freise, J; Schmolz, E

    2014-05-01

    Rodents can harbor and transmit pathogens that can cause severe disease in humans, companion animals and livestock. Such zoonotic pathogens comprise more than two thirds of the currently known human pathogens. The epidemiology of some zoonotic pathogens, such as hantaviruses, can be linked to the population dynamics of the rodent host. In this case, during an outbreak of the rodent host population many human infections may occur. In other rodent-borne zoonotic diseases such phenomena are not known and in many cases the rodent host specificity of a given pathogen is unclear. The monitoring of relevant rodent populations and of the rodent-borne zoonotic pathogens is essential to (1) understand the distribution and epidemiology of pathogens and (2) develop forecasting tools to predict outbreaks of zoonoses. Presently, there are no systematic long-term monitoring programs in place for zoonoses in Germany. Rodent monitoring activities are largely restricted to the plant protection sector, such as for the common vole (Microtus arvalis) and forest-damaging rodents. However, during the last 10-15 years a number of specific research projects have been initiated and run for a few years and Norway rat (Rattus norvegicus) monitoring has been implemented in Hamburg and Lower Saxony. Based on close cooperation of federal and state authorities and research institutions these efforts could be utilized to gain information about the distribution and importance of rodent-borne zoonoses. Nevertheless, for the integration of rodent population dynamics and zoonotic disease patterns and especially for developing predictive models, long-term monitoring is urgently required. To establish a systematic long-term monitoring program, existing networks and cooperation need to be used, additional collaborators (e.g., pest control operators) should be included and synergetic effects of different scientific fields should be utilized.

  13. An Investigation of Structural Capacity as a Component of Monitoring and Evaluation in Project Success of Road Construction Projects in Kenya

    Directory of Open Access Journals (Sweden)

    Ali Ibrahim Hassan

    2013-08-01

    Full Text Available The transport sector in Kenya contributes about 6% of the gross domestic product and is critical in providing the necessary linkages for promoting national and regional interconnectivity as well as trade. Developments in the road construction industry in Kenya are increasing in size, technology complexity, interdependencies, and variations in demands from clients. Enormous donor and government resources are provided to various road contractors for the construction of road projects in Kenya.Monitoring and evaluation of road projects implementation is paramount in determining the success of road construction projects. It is hypothesized that poor and inefficient monitoring and evaluation of road construction projects could be one of the causes of endemic project delays and poor workmanships on completed road projects. It was therefore imperative to examine the monitoring and evaluation systems used in road construction projects in Kenya, and assess their effectiveness, with a particular emphasis on the components of monitoring and evaluation system. The objective of this study was therefore to assess the influence of monitoring and evaluation system on project success. The target population of this study was the road contractors and regulatory bodies involved in ongoing road construction projects in Nairobi city and its environs. A descriptive study design was used to collect quantitative and qualitative data. Primary data was collected by use of structured questionnaires. The questionnaire was designed to respond to research question. Secondary data was collected through review of published literature such as journal articles, published theses and textbooks. The data collected from the field was captured using Statistical Package for Social Sciences (SPSS and Microsoft excel. Descriptive statistics including frequency, percentages and means were employed and a summary graphs, pie charts and frequency distribution tables given. Content analysis

  14. A Web-Based System for Monitoring and Controlling Multidisciplinary Design Projects

    Science.gov (United States)

    Salas, Andrea O.; Rogers, James L.

    1997-01-01

    In today's competitive environment, both industry and government agencies are under enormous pressure to reduce the time and cost of multidisciplinary design projects. A number of frameworks have been introduced to assist in this process by facilitating the integration of and communication among diverse disciplinary codes. An examination of current frameworks reveals weaknesses in various areas such as sequencing, displaying, monitoring, and controlling the design process. The objective of this research is to explore how Web technology, in conjunction with an existing framework, can improve these areas of weakness. This paper describes a system that executes a sequence of programs, monitors and controls the design process through a Web-based interface, and visualizes intermediate and final results through the use of Java(Tm) applets. A small sample problem, which includes nine processes with two analysis programs that are coupled to an optimizer, is used to demonstrate the feasibility of this approach.

  15. Monitoring and Evaluation of Environmental Flow Prescriptions for Five Demonstration Sites of the Sustainable Rivers Project

    Science.gov (United States)

    Konrad, Christopher P.

    2010-01-01

    The Nature Conservancy has been working with U.S. Army Corps of Engineers (Corps) through the Sustainable Rivers Project (SRP) to modify operations of dams to achieve ecological objectives in addition to meeting the authorized purposes of the dams. Modifications to dam operations are specified in terms of environmental flow prescriptions that quantify the magnitude, duration, frequency, and seasonal timing of releases to achieve specific ecological outcomes. Outcomes of environmental flow prescriptions implemented from 2002 to 2008 have been monitored and evaluated at demonstration sites in five rivers: Green River, Kentucky; Savannah River, Georgia/South Carolina; Bill Williams River, Arizona; Big Cypress Creek, Texas; and Middle Fork Willamette River, Oregon. Monitoring and evaluation have been accomplished through collaborative partnerships of federal and state agencies, universities, and nongovernmental organizations.

  16. 2009 Groundwater Monitoring Report Project Shoal Area, Corrective Action Unit 447

    Energy Technology Data Exchange (ETDEWEB)

    None

    2010-03-01

    This report presents the 2009 groundwater monitoring results collected by the U.S. Department of Energy (DOE) Office of Legacy Management (LM) at the Project Shoal Area (PSA) Subsurface Corrective Action Unit (CAU) 447 in Churchill County, Nevada. Responsibility for the environmental site restoration of the PSA was transferred from the DOE Office of Environmental Management to LM on October 1, 2006. The environmental restoration process and corrective action strategy for CAU 447 are conducted in accordance with the Federal Facility Agreement and Consent Order (FFACO 1996, as amended February 2008) entered into by DOE, the U.S. Department of Defense, and the State of Nevada. The corrective action strategy for the site includes monitoring in support of site closure. This report summarizes investigation activities associated with CAU 447 that were conducted at the PSA during fiscal year 2009.

  17. Monitoring of stage and velocity, for computation of discharge in the Summit Conduit near Summit, Illinois, 2010-2012

    Science.gov (United States)

    Johnson, Kevin K.; Goodwin, Greg E.

    2013-01-01

    Lake Michigan diversion accounting is the process used by the U. S. Army Corps of Engineers to quantify the amount of water that is diverted from the Lake Michigan watershed into the Illinois and Mississippi River Basins. A network of streamgages within the Chicago area waterway system monitor tributary river flows and the major river flow on the Chicago Sanitary and Ship Canal near Lemont as one of the instrumental tools used for Lake Michigan diversion accounting. The mean annual discharges recorded by these streamgages are used as additions or deductions to the mean annual discharge recorded by the main stream gaging station currently used in the Lake Michigan diversion accounting process, which is the Chicago Sanitary and Ship Canal near Lemont, Illinois (station number 05536890). A new stream gaging station, Summit Conduit near Summit, Illinois (station number 414757087490401), was installed on September 23, 2010, for the purpose of monitoring stage, velocity, and discharge through the Summit Conduit for the U.S. Army Corps of Engineers in accordance with Lake Michigan diversion accounting. Summit Conduit conveys flow from a small part of the lower Des Plaines River watershed underneath the Des Plaines River directly into the Chicago Sanitary and Ship Canal. Because the Summit Conduit discharges into the Chicago Sanitary and Ship Canal upstream from the stream gaging station at Lemont, Illinois, but does not contain flow diverted from the Lake Michigan watershed, it is considered a flow deduction to the discharge measured by the Lemont stream gaging station in the Lake Michigan diversion accounting process. This report offers a technical summary of the techniques and methods used for the collection and computation of the stage, velocity, and discharge data at the Summit Conduit near Summit, Illinois stream gaging station for the 2011 and 2012 Water Years. The stream gaging station Summit Conduit near Summit, Illinois (station number 414757087490401) is an

  18. Interstage Home Monitoring After Newborn First-Stage Palliation for Hypoplastic Left Heart Syndrome: Family Education Strategies.

    Science.gov (United States)

    Nieves, Jo Ann; Uzark, Karen; Rudd, Nancy A; Strawn, Jennifer; Schmelzer, Anne; Dobrolet, Nancy

    2017-04-01

    Children born with hypoplastic left heart syndrome are at high risk for serious morbidity, growth failure, and mortality during the interstage period, which is the time from discharge home after first-stage hypoplastic left heart syndrome palliation until the second-stage surgical intervention. The single-ventricle circulatory physiology is complex, fragile, and potentially unstable. Multicenter initiatives have been successfully implemented to improve outcomes and optimize growth and survival during the interstage period. A crucial focus of care is the comprehensive family training in the use of home surveillance monitoring of oxygen saturation, enteral intake, weight, and the early recognition of "red flag" symptoms indicating potential cardiopulmonary or nutritional decompensation. Beginning with admission to the intensive care unit of the newborn with hypoplastic left heart syndrome, nurses provide critical care and education to prepare the family for interstage home care. This article presents detailed nursing guidelines for educating families on the home care of their medically fragile infant with single-ventricle circulation. ©2017 American Association of Critical-Care Nurses.

  19. IEA GHG Weyburn CO{sub 2} monitoring and storage project : summary report 2000-2004

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, M. (ed.) [Regina Univ., SK (Canada); Monea, M. (ed.) [Petroleum Technology Research Centre, Regina, SK (Canada); Whittaker, S. [Saskatchewan Industry and Resources, Regina, SK (Canada); White, D. [Geological Survey of Canada, Ottawa, ON (Canada); Law, D. [Alberta Research Council, Edmonton, AB (Canada); Chalaturnyk, R. [Alberta Univ., Edmonton, AB (Canada)

    2004-07-01

    The Weyburn CO{sub 2} Monitoring and Storage Project is a multi-million dollar Canadian research project launched in July 2000 to determine the feasibility of geological storage of carbon dioxide (CO{sub 2}) at EnCana's enhanced oil recovery project at its Weyburn Unit in Saskatchewan. This book reviews the operating status of the project and provides a new understanding of the geological storage of greenhouse gases, particularly carbon dioxide. The project aims to predict and verify the ability of an oil reservoir to securely and economically store CO{sub 2}. Various mechanisms for geological storage were examined along with the degree to which CO{sub 2} can be permanently stored in geological formations. The Weyburn field has been subjected to waterflooding since 1964 and extensive use of horizontal wells since 1991. The first phase of the CO{sub 2} enhanced oil recovery scheme began in September 2000 in 18 inverted 9-spot patterns. The flood will be expanded over the next 15 years to a total of 75 patterns. A total of 20 million tonnes of CO{sub 2} is expected to be injected into the reservoir over the life of the project. The CO{sub 2} is a purchased by-product from the Dakota Gasification Company's synthetic fuel plant in Beulah, North Dakota. The carbon dioxide is transported via a 320 km pipeline to Weyburn. The project has been monitored and evaluated since its launch. This study involved an assessment of geochemical reactions from the action of CO{sub 2} on reservoir rock and the impact that it might have on geomechanical integrity and CO{sub 2} sequestration. A geoscience model of the storage medium was developed to identify potential migration pathways for CO{sub 2}. Risk assessments were conducted to predict long-term fate of CO{sub 2} within the storage sites. An economic model was also developed to define the limits of economic storage during and after enhanced oil recovery operations. refs., tabs., figs.

  20. Project GeoWSN: High precision but low-cost GNSS landslide monitoring in Austria

    Science.gov (United States)

    Koch, Daniel; Brandstätter, Michael; Kühtreiber, Norbert

    2014-05-01

    At present, GNSS monitoring of landslides is an accepted and approved method to detect movements of slopes at risk in the sub-centimetre level. However, high-precision geodetic GNSS-receivers are expensive, therefore this monitoring method is not widely applied. Recently low-cost GNSS-receivers are conquering the geodetic market and are well suited for a cost effective and yet precise GNSS-monitoring. During the project GeoWSN, which was funded by the Austrian Research Promotion Agency (FFG), an applicable low-cost monitoring system was developed at Graz University of Technology. The system is based on a so-called Wireless Sensor Network (WSN) consisting of low-cost GNSS-receivers, temperature and humidity sensors and inertial measurement units. Additionally energy-harvesting technologies and power-saving algorithms provide that the system is energy- autarkic. For real-time applications, a communication link between the sensor nodes is implemented. The relative positioning method RTK (Real Time Kinematic) is applied to reach the highest possible accuracy. The GeoWSN sensor nodes enable the detection of possible movements in the real-time processed positions of the sensor nodes. To ensure a real-time evaluation and interpretation of the data, the current status of the slope can be acquired by a local warning centre. Therefore, affected people can be warned within a short latency. Several test-scenarios have shown the acceptance of the system at the warning centre of Styria, Austria. This contribution should give an overview of the main idea of a low-cost warning system and results of the project GeoWSN.

  1. The evaluation stage of the Hoeven Outcome Monitor (HOM): Towards an evidence based groundwork in forensic mental health.

    Science.gov (United States)

    Keune, Lobke H; de Vogel, Vivienne; van Marle, Hjalmar J C

    2017-02-27

    This study examined if a macro-, meso-, and micro outcome measurement instrument that constitutes the evaluation stage of a Dutch forensic psychiatric outcome monitor, the Hoeven Outcome Monitor (HOM), can provide a first step towards a more evidence based groundwork in forensic mental health. General, serious, very serious, special, and tbs meriting recidivism during treatment, after treatment, and overall were charted for forensic psychiatric patients discharged from a Dutch forensic psychiatric centre between 1999 and 2008 (N=164). Re-conviction data were obtained from the official Criminal Records System, and the mean follow-up time was 116.2months. First, the results showed that the macro-measurements provide comparative outcome measures to generate insight into the overall effectiveness of forensic psychiatric treatment. Second, the meso-measurements yielded clinically relevant treatment outcome data for all discharged patients to generate a complete view of treatment effectiveness. Finally, the micro-measurements allowed access to detailed patient and treatment effectiveness assessments that provides the empirical foundation to conduct aetiological research into the prediction and control of high-risk behaviour. Thus, an outcome measurement instrument in line with Evidence Based Medicine and best practice guidelines was designed that provides an empirically sound evaluation framework for treatment effectiveness, and an impetus for the development of effective interventions to generate an evidence based groundwork in forensic mental health.

  2. The AAL project: automated monitoring and intelligent analysis for the ATLAS data taking infrastructure

    Science.gov (United States)

    Kazarov, A.; Lehmann Miotto, G.; Magnoni, L.

    2012-06-01

    The Trigger and Data Acquisition (TDAQ) system of the ATLAS experiment at CERN is the infrastructure responsible for collecting and transferring ATLAS experimental data from detectors to the mass storage system. It relies on a large, distributed computing environment, including thousands of computing nodes with thousands of application running concurrently. In such a complex environment, information analysis is fundamental for controlling applications behavior, error reporting and operational monitoring. During data taking runs, streams of messages sent by applications via the message reporting system together with data published from applications via information services are the main sources of knowledge about correctness of running operations. The flow of data produced (with an average rate of O(1-10KHz)) is constantly monitored by experts to detect problem or misbehavior. This requires strong competence and experience in understanding and discovering problems and root causes, and often the meaningful information is not in the single message or update, but in the aggregated behavior in a certain time-line. The AAL project is meant at reducing the man power needs and at assuring a constant high quality of problem detection by automating most of the monitoring tasks and providing real-time correlation of data-taking and system metrics. This project combines technologies coming from different disciplines, in particular it leverages on an Event Driven Architecture to unify the flow of data from the ATLAS infrastructure, on a Complex Event Processing (CEP) engine for correlation of events and on a message oriented architecture for components integration. The project is composed of 2 main components: a core processing engine, responsible for correlation of events through expert-defined queries and a web based front-end to present real-time information and interact with the system. All components works in a loose-coupled event based architecture, with a message broker

  3. Power Monitoring and Control for Large Scale projects: SKA, a case study

    CERN Document Server

    Barbosa, Domingos; Maia, Dalmiro; Carvalho, Bruno; Vieira, Jorge; Swart, Paul; Roux, Gerhard Le; Natarajan, Swaminathan; van Ardenne, Arnold; Seca, Luis

    2016-01-01

    Large sensor-based science infrastructures for radio astronomy like the SKA will be among the most intensive data-driven projects in the world, facing very high demanding computation, storage, management, and above all power demands. The geographically wide distribution of the SKA and and its associated processing requirements in the form of tailored High Performance Computing (HPC) facilities, require a Greener approach towards the Information and Communications Technologies (ICT) adopted for the data processing to enable operational compliance to potentially strict power budgets. Addressing the reduction of electricity costs, improve system power monitoring and the generation and management of electricity at system level is paramount to avoid future inefficiencies and higher costs and enable fulfillments of Key Science Cases. Here we outline major characteristics and innovation approaches to address power efficiency and long-term power sustainability for radio astronomy projects, focusing on Green ICT for s...

  4. Environmental monitoring for the DOE coolside and LIMB demonstration extension projects

    Energy Technology Data Exchange (ETDEWEB)

    White, T.; Contos, L.; Adams, L. (Radian Corp., Research Triangle Park, NC (United States))

    1992-03-01

    The purpose of this document is to present environmental monitoring data collected during the US Department of Energy Limestone Injection Multistage Burner (DOE LIMB) Demonstration Project Extension at the Ohio Edison Edgewater Generating Station in Lorain, Ohio. The DOE project is an extension of the US Environmental Protection Agency's (EPA's) original LIMB Demonstration. The program is operated nuclear DOE's Clean Coal Technology Program of emerging clean coal technologies'' under the categories of in boiler control of oxides of sulfur and nitrogen'' as well as post-combustion clean-up.'' The objective of the LIMB program is to demonstrate the sulfur dioxide (SO{sub 2}) and nitrogen oxide (NO{sub x}) emission reduction capabilities of the LIMB system. The LIMB system is a retrofit technology to be used for existing coal-fired boilers equipped with electrostatic precipitators (ESPs).

  5. Floristic Quality Index: An assessment tool for restoration projects and monitoring sites in coastal Louisiana

    Science.gov (United States)

    Cretini, K.F.; Steyer, G.D.

    2011-01-01

    The Coastwide Reference Monitoring System (CRMS) program was established to assess the effectiveness of individual coastal restoration projects and the cumulative effects of multiple projects at regional and coastwide scales. In order to make these assessments, analytical teams have been assembled for each of the primary data types sampled under the CRMS program, including vegetation, hydrology, landscape, and soils. These teams consist of scientists and support staff from the U.S. Geological Survey and other Federal agencies, the Louisiana Office of Coastal Protection and Restoration, and university academics. Each team is responsible for developing or identifying parameters, indices, or tools that can be used to assess coastal wetlands at various scales. The CRMS Vegetation Analytical Team has developed a Floristic Quality Index for coastal Louisiana to determine the quality of a wetland based on its plant species composition and abundance.

  6. Seismic monitoring and analysis of deep geothermal projects in St Gallen and Basel, Switzerland

    Science.gov (United States)

    Edwards, Benjamin; Kraft, Toni; Cauzzi, Carlo; Kästli, Philipp; Wiemer, Stefan

    2015-05-01

    Monitoring and understanding induced seismicity is critical in order to estimate and mitigate seismic risk related to numerous existing and emerging techniques for natural resource exploitation in the shallow-crust. State of the art approaches for guiding decision making, such as traffic light systems, rely heavily on data such as earthquake location and magnitude that are provided to them. In this context we document the monitoring of a deep geothermal energy project in St Gallen, Switzerland. We focus on the issues of earthquake magnitude, ground motion and macroseismic intensity which are important components of the seismic hazard associated to the project. We highlight the problems with attenuation corrections for magnitude estimation and site amplification that were observed when trying to apply practices used for monitoring regional seismicity to a small-scale monitoring network. Relying on the almost constant source-station distance for events in the geothermal `seismic cloud' we developed a simple procedure, calibrated using several ML > 1.3 events, which allowed the unbiased calculation of ML using only stations of the local monitoring network. The approach determines station specific ML correction terms that account for both the bias of the attenuation correction in the near field and amplification at the site. Since the smallest events (ML computed over the whole network this single station approach was shown to provide robust estimates (±0.17 units) for the events down to ML = -1. The relation could then be used to estimate the magnitude of even smaller events (ML specific ML corrections due to local amplification. We analysed ground-motion and detailed macroseismic reports resulting from the 2013 July 20 St Gallen ML = 3.5 ± 0.1 (Mw = 3.3-3.5 ± 0.1) `main shock' and compared it to a similar ML = 3.4 ± 0.1 event (Mw = 3.2 ± 0.1) that occurred in 2006 at another deep geothermal project in Basel, Switzerland. Differences in ground motion amplitudes

  7. Use Of The Operational Air Quality Monitor (AQM) For In-Flight Water Testing Project

    Science.gov (United States)

    Macatangay, Ariel

    2014-01-01

    A primary requirement for manned spaceflight is Environmental Health which ensures air and water contaminants, acoustic profiles, microbial flora, and radiation exposures within the cabin are maintained to levels needed for crew health and for vehicle system functionality. The reliance on ground analyses of returned samples is a limitation in the current environmental monitoring strategy that will prevent future Exploration missions beyond low-Earth orbit. This proposal attempts to address this shortcoming by advancing in-flight analyses of water and air. Ground analysis of in-flight, air and water samples typically employ vapor-phase analysis by gas chromatography-mass spectrometry (GC-MS) to identify and quantify organic compounds present in the samples. We envision the use of newly-developed direct ionization approaches as the most viable avenue leading towards an integrated analytical platform for the monitoring of water, air, and, potentially bio-samples in the cabin environment. Development of an in-flight instrument capable of analyzing air and water samples would be the logical next step to meeting the environmental monitoring needs of Exploration missions. Currently, the Air Quality Monitor (AQM) on-board ISS provides this specific information for a number of target compounds in the air. However, there is a significant subset of common target compounds between air and water. Naturally, the following question arises, "Can the AQM be used for both air and water quality monitoring?" Previous directorate-level IR&D funding led to the development of a water sample introduction method for mass spectrometry using electrothermal vaporization (ETV). This project will focus on the integration of the ETV with a ground-based AQM. The capabilities of this integrated platform will be evaluated using a subset of toxicologically important compounds.

  8. IMPROVING CLIENT INTERNAL CAPABILITY TO MONITOR PUBLIC-PRIVATE PARTNERSHIPS PROJECTS: A REVIEW

    Directory of Open Access Journals (Sweden)

    Abdullahi Ahmed Umar

    2012-01-01

    Full Text Available Public-Private Partnerships (PPP or Private Finance Initiatives (PFI are increasingly becoming very popular with governments across the globe for the provision of public infrastructure and services. When contracted, the public sector client believing the private sector will act in accordance with ‘bounded rationality’, ignores the constant monitoring and review process which is an integral part of any project. However, the failures of some of these partnerships and the social and economic costs incurred due to laxity in monitoring reminds us of the need to develop the permanent bureaucratic machinery of government, who share the government’s unique objectives of end-users satisfaction rather than shareholders’, to perform the monitoring of these projects. Though the public sector has been delivering projcets for dacades, the complexities associated with the PFI strategy has opened up new challenges for its staff. Most failures and moral harzards are only discovered after scandals evoke investigations like the case of Enron or when public criticisms force the government to reverse their decision as in the case of the Skye toll bridge by which time a lot of damage would have be done. Literature has shown that when employees are trained and engaged in organisational decisions and policy planning they make policy executions easier. Therefore, considering the Theoretical ideology behind the PFI of the asset being returned to the Public sector at the end of the concession, it becomes pertinent for proper training of the public sector staff. Public sector officials, if adequately trained and motivated can perform the tasks being contracted out to private consultants thereby re-affirming government’s commitment to its Value for Money (VFM proposition. Though the public sector staff strength has been depleted due to the adoption of New Public Management (NPM, however the remaining qualified staff can be pooled to create an

  9. High altitude environmental monitoring: the SHARE project and CEOP-HE

    Science.gov (United States)

    Tartari, G.

    2009-04-01

    Mountain areas above 2,500 m a.s.l. constitute about 25% of the Earth's surface and play a fundamental role in the global water balance, while influencing global climate and atmospheric circulation systems. Several millions, including lowlanders, are directly affected by the impacts of climate change on glaciers and water resource distribution. Mountains and high altitude plateaus are subject to the highest rate of temperature increase (e.g., Tibetan Plateau) and are recognized as particularly vulnerable to the effects of climate change. In spite of this, the number of permanent monitoring sites in the major environmental networks decreases with altitude. On a sample of two hundred high altitude automatic weather stations located above 2,500 m a.s.l., less than 20% are over 4,000 m, while there are only 24 stations in the world that could be considered "complete" high altitude observatories. Furthermore, entire mountain areas are left uncovered, creating significant data gaps which make reliable modelling and forecasting nearly impossible. In response to these problems, Ev-K2-CNR has developed the project SHARE (Stations at High Altitude for Research on the Environment) with the support of the Italian government and in collaboration with UNEP. This integrated environmental monitoring and research project aims to improve knowledge on the local, regional and global consequences of climate change in mountain regions and on the influence of high elevations on climate, atmospheric circulation and hydrology. SHARE today boasts a network of 13 permanent monitoring stations between 2,165 m and 8,000 m. Affiliated researchers have produced over 150 scientific publications in atmospheric sciences, meteorology and climate, glaciology, limnology and paleolimnology and geophysics. SHARE network data is also contributed to international programs (UNEP-ABC, WMO-GAW, WCRP-GEWEX-CEOP, NASA-AERONET, ILTER, EU-EUSAAR, EU-ACCENT). Within this context, the CEOP-High Elevations (CEOP

  10. Implementation of modern technology for high-viscosity oil production on Sakhalin Island, Russia: issues and replies at the first stage of the pilot project

    Energy Technology Data Exchange (ETDEWEB)

    Yuryev, Dmitry [RN - Sakhalin NIP Imorneft (Russian Federation)

    2011-07-01

    On Sakhalin Island In Russia, oil production fields are now facing a decrease in production. Heavy oil, oil with high viscosity, is a significant part of the remaining resources and its use is thus essential to maintain and increase oil production. The aim of this paper is to present the results of the first stage of a project testing modern technology to recover heavy oil. This pilot project is located in the Katangli Uiglekuty fields and is conducted using shallow horizontal well drilling, steam injection expansion and improvement and well completion optimization. Results of the first stage of the project allowed technical and economical indices to be updated, leading to assessment of further project optimization and implementation. This paper presented a project to recover heavy oil on Sakhalin Island with modern technologies and its first stage results.

  11. The ISTIMES project: a new integrated system for monitoring critical transport infrastructures interested by natural hazards

    Science.gov (United States)

    Proto, Monica; Massimo, Bavusi; Francesco, Soldovieri

    2010-05-01

    The research project "Integrated System for Transport Infrastructure surveillance and Monitoring by Electromagnetic Sensing" (ISTIMES), was approved in the 7th Framework Programme, in the Joint Call ICT and Security and started on 1st July 2009. The purpose of ISTIMES project is to design, assess and promote an ICT-based system, exploiting distributed and local sensors, for non-destructive electromagnetic monitoring in order to achieve the critical transport infrastructures more reliable and safe. The transportation sector's components are susceptible to the consequences of natural disasters and can also be attractive as terrorist targets. The sector's size, its physically dispersed and decentralized nature, the many public and private entities involved in its operations, the critical importance of cost considerations, and the inherent requirement of convenient accessibility to its services by all users - make the transportation particularly vulnerable to security and safety threats. As well known, the surface transportation system consists of interconnected infrastructures including highways, transit systems, railroads, airports, waterways, pipelines and ports, and the vehicles, aircraft, and vessels that operate along these networks. Thus, interdependencies exist between transportation and nearly every other sector of the economy and the effective operation of this system is essential to the European economic productivity; therefore, transportation sector protection is of paramount importance since threats to it may impact other industries that rely on it. The system exploits an open network architecture that can accommodate a wide range of sensors, static and mobile, and can be easily scaled up to allow the integration of additional sensors and interfacing with other networks. It relies on heterogeneous state-of-the-art electromagnetic sensors, enabling a self-organizing, self-healing, ad-hoc networking of terrestrial sensors, supported by specific satellite

  12. Electromagnetic monitoring of the Earth's interior in the frame of the MEM Project

    Directory of Open Access Journals (Sweden)

    L. Santarelli

    2008-06-01

    Full Text Available The MEM Project (Magnetic and Electric fields Monitoring was activated in the INGV Observatory of L’Aquila since 2004. The principal purpose of the project is to create in Central Italy a network of observatories to monitoring the electromagnetic signals in the frequency band [0.001 Hz - 100 kHz]. This band includes natural signals (magnetic pulsations of magnetospheric origin, Earth-ionosphere resonance mode signals, atmospheric noise, and so on and artificial signals (power line emissions, VLF radio transmissions, and so on. The innovative characteristic of the project is the approach chosen to study the complex problem concerning the representation of the spatial and temporal distributions of the electromagnetic fields in the band of interest. Both the distributions can be represented by some parameters containing the locations and the characteristics of the sources of the electromagnetic signals. When all the stations will be in operation the wide-band interferometry will be applied. Combining the simultaneous observations of the electromagnetic field measured in the stations of the network, we will be able to obtain detailed information about the investigated electromagnetic sources. A new measurement system has been developed to fulfil these requirements focusing on the automation of the measurements. The system is designed for long term recording of the electromagnetic fields in a wide frequency band. In the frequency band [1Hz - 100 kHz] the three components of the magnetic field and the three components of atmospheric electric field are processed in real time using DSP (Digital Signal Processing techniques. In the frequency band [0.001 - 25]Hz the two components of the telluric field and the three components of the magnetic field are recorded as sampled (100Hz. One of the main scientific objectives of the MEM project is the long term monitoring of the geodynamical processes, such as the earthquakes, by the calculation of the Poynting

  13. New idea of geomagnetic monitoring through ENA detection from the International Space Station: ENAMISS project

    Science.gov (United States)

    Milillo, Anna; De Angelis, Elisabetta; Orsini, Stefano; Rubini, Alda; Evangelista, Yuri; Mura, Alessandro; Rispoli, Rosanna; Vertolli, Nello; Carrubba, Elisa; Donati, Alessandro; Di Lellis, Andrea Maria; Plainaki, Christina; Lazzarotto, Francesco

    2016-04-01

    Remote sensing of Energetic Neutral Atoms (ENA) in the Earth's environment has been proven to be a successful technique able to provide detailed information on the ring current plasma population at energies below 100 keV. Indeed, the existing space weather databases usually include a good coverage of Sun and solar wind monitoring. The global imaging of the Earth's magnetosphere/ ionosphere is usually obtained by the high-latitudes monitoring of aurorae, ground magnetic field variations and high-latitude radio emissions. The equatorial magnetic field variations on ground, from which the geomagnetic indices like Dst, Sym-H and Asym-H are derived, include the effects of all current systems (i.e. ring current, Chapman -Ferraro current, tails currents, etc...) providing a kind of global information. Nevertheless, the specific information related to the ring current cannot be easily derived from such indices. Only occasional local plasma data are available by orbiting spacecraft. ENA detection is the only way to globally view the ring current populations. Up-to-now this technique has been used mainly from dedicated high altitude polar orbiting spacecraft, which do not allow a continuous and systematic monitoring, and a discrimination of the particle latitude distribution. The Energetic Neutral Atoms Monitor on the International space Station (ENAMISS) project intends to develop an ENA imager and install it on the ISS for continuous monitoring of the spatially distributed ring current plasma population. ISS is the ideal platform to perform continuous ENA monitoring since its particular low altitude and medium/low latitude orbit allows wide-field ENA images of various magnetospheric regions. The calibrated ENA data, the deconvolved ion distributions and ad-hoc ENA-based new geomagnetic indices will be freely distributed to the space weather community. Furthermore, new services based on plasma circulation models, spacecraft surface charging models and radiation dose models

  14. The SSC cycle: a PDCA approach to address site-specific characteristics in a continuous shallow water quality monitoring project.

    Science.gov (United States)

    Miles, Eduardo J

    2008-05-01

    In any water quality-monitoring project there are several critical success factors that must be adequately addressed in order to ensure the implementation and realization of the monitoring objectives. Site selection is one of these critical success factors. The monitoring sites must be selected to comply with the monitoring and data quality objectives. In the real world, ideal monitoring setting conditions are difficult to achieve, and compromises must be made in order to locate the monitoring stations that best represent the environment to be monitored. Site-specific characteristics are all the environmental, logistical and management factors particular to the monitoring site, that could influence the fulfilment of the monitoring and data quality objectives. Therefore, during the site selection process, it is essential to properly consider and evaluate these site-specific characteristics. The SSC cycle was developed with this goal in mind, to assist the monitoring team to systematically address site-specific characteristics. The cycle is a methodology to organize the site-specific characteristics in different categories, and to ensure a comprehensive overview of these characteristics throughout the project life cycle.

  15. Sustainable Seas Student Intertidal Monitoring Project at Duxbury Reef in Bolinas, CA

    Science.gov (United States)

    Boesel, A.; Soave, K.; Dean, A.; Grimaldi, Z.; Buie, A.; Dattels, C.; Steiger, C.; Wallace, K.; Salmi, I.; Tillapaugh, J.

    2011-12-01

    Kathy Soave, Amy Dean, Alexa Boesel, Andrew Buie, Celia Dattels, Zoe Grimaldi, Isabella Salmi, Cameryn Steiger, Joey Tillapaugh, Kathleen Wallace The Sustainable Seas Student Monitoring Project at the Branson School in Ross, CA has monitored Duxbury Reef in Bolinas, CA since 1999, in cooperation with the Farallones Marine Sanctuary Association and the Gulf of Farallones National Marine Sanctuary. Goals of this student-run project include: 1) To monitor the rocky intertidal habitat and develop a baseline database of invertebrates and algal density and abundance; 2) To contribute to the conservation of the rocky intertidal habitat through education of students and visitors about intertidal species and the requirements for maintaining a healthy, diverse intertidal ecosystem; 3) To increase stewardship in the Gulf of the Farallones National Marine Sanctuary; and 4) To contribute abundance and population data on key algae and invertebrate species to the national database, LiMPETS (Long Term Monitoring Program & Experiential Training for Students). Student volunteers complete an intensive training course on the natural history of intertidal invertebrates and algae, identification of key species, rocky intertidal monitoring techniques, and history of the sanctuary. Students identify and count key invertebrate and algae species along two permanent transects and, using randomly determined points, within a permanent 100 m2 area, three times per year (fall, winter, and late spring). Using the data collected since 2004, we will once again compare population densities, seasonal abundance and long-term population trends of key algal and invertebrate species, including Tegula funebralis and Anthopluera elegantissima. Future analyses and investigations will include intertidal abiotic factors (including water temperature and human foot-traffic) to enhance insights into the workings of the Duxbury Reef ecosystem, in particular, the high and mid-intertidal zones experiencing the

  16. The Lick AGN Monitoring Project: Photometric Light Curves and Optical Variability Characteristics

    CERN Document Server

    Walsh, Jonelle L; Bentz, Misty C; Barth, Aaron J; Baliber, Nairn; Li, Weidong; Stern, Daniel; Bennert, Vardha Nicola; Brown, Timothy M; Canalizo, Gabriela; Filippenko, Alexei V; Gates, Elinor L; Greene, Jenny E; Malkan, Matthew A; Sakata, Yu; Street, Rachel A; Treu, Tommaso; Woo, Jong-Hak; Yoshii, Yuzuru

    2009-01-01

    The Lick AGN Monitoring Project targeted 13 nearby Seyfert 1 galaxies with the intent of measuring the masses of their central black holes using reverberation mapping. The sample includes 12 galaxies selected to have black holes with masses roughly in the range 10^6-10^7 solar masses, as well as the well-studied AGN NGC 5548. In conjunction with a spectroscopic monitoring campaign, we obtained broad-band B and V images on most nights from 2008 February through 2008 May. The imaging observations were carried out by four telescopes: the 0.76-m Katzman Automatic Imaging Telescope (KAIT), the 2-m Multicolor Active Galactic Nuclei Monitoring (MAGNUM) telescope, the Palomar 60-in (1.5-m) telescope, and the 0.80-m Tenagra II telescope. Having well-sampled light curves over the course of a few months is useful for obtaining the broad-line reverberation lag and black hole mass, and also allows us to examine the characteristics of the continuum variability. In this paper, we discuss the observational methods and the ph...

  17. Yakima/Klickitat Fisheries Project; Klickitat Only Monitoring and Evaluation, 2002-2003 Annual Report.

    Energy Technology Data Exchange (ETDEWEB)

    Sampson, Melvin; Evenson, Rolf

    2003-12-01

    The monitoring and evaluation activities described in this report were determined by consensus of the scientists from the Yakama Nation (YN). Klickitat Subbasin Monitoring and Evaluation (M&E) activities have been subjected to scientific and technical review by members of YKFP's Science/Technical Advisory Committee (STAC) as part of the YKFP's overall M&E proposal. Yakama Nation YKFP project biologists have transformed the conceptual design into the tasks described. This report summarizes progress and results for the following major categories of YN-managed tasks under this contract: (1) Monitoring and Evaluation - Accurately characterize baseline available habitat and salmonid populations pre-habitat restoration and pre-supplementation. (2) EDT Modeling - Identify and evaluate habitat and artificial production enhancement options. (3) Genetics - Characterize the genetic profile of wild steelhead in the Klickitat Basin. (4) Ecological Interactions - Determine the presence of pathogens in wild and naturally produced salmonids in the Klickitat Basin and develop supplementation strategies using this information.

  18. 2015 Groundwater Monitoring Report Project Shoal Area: Subsurface Correction Unit 447

    Energy Technology Data Exchange (ETDEWEB)

    Findlay, Rick [Navarro Research and Engineering, Oak Ridge, TN (United States)

    2016-04-01

    The Project Shoal Area in Nevada was the site of a 12-kiloton-yield underground nuclear test in 1963. Although the surface of the site has been remediated, investigation of groundwater contamination resulting from the test is still in the corrective action process. Annual sampling and hydraulic head monitoring are conducted at the site as part of the subsurface corrective action strategy. The corrective action strategy is currently focused on revising the site conceptual model (SCM) and evaluating the adequacy of the monitoring well network. Some aspects of the SCM are known; however, two major concerns are the uncertainty in the groundwater flow direction and the cause of rising water levels in site wells west of the shear zone. Water levels have been rising in the site wells west of the shear zone since the first hydrologic characterization wells were installed in 1996. Although water levels in wells west of the shear zone continue to rise, the rate of increase is less than in previous years. The SCM will be revised, and an evaluation of the groundwater monitoring network will be conducted when water levels at the site have stabilized to the agreement of both the U.S. Department of Energy Office of Legacy Management and the Nevada Division of Environmental Protection.

  19. California Groundwater Ambient Monitoring and Assessment (GAMA) Program Priority Basin Project--shallow aquifer assessment

    Science.gov (United States)

    ,

    2013-01-01

    The California State Water Resources Control Board’s (SWRCB) GAMA Program is a comprehensive assessment of statewide groundwater quality in California. From 2004 to 2012, the GAMA Program’s Priority Basin Project focused on assessing groundwater resources used for public drinking-water supplies. More than 2,000 public-supply wells were sampled by U.S. Geological Survey (USGS) for this effort. Starting in 2012, the GAMA Priority Basin Project began an assessment of water resources in shallow aquifers in California. These shallow aquifers provide water for domestic and small community-supply wells, which are often drilled to shallower depths in the groundwater system than public-supply wells. Shallow aquifers are of interest because shallow groundwater may respond more quickly and be more susceptible to contamination from human activities at the land surface, than the deeper aquifers. The SWRCB’s GAMA Program was developed in response to the Groundwater Quality Monitoring Act of 2001 (Water Code sections 10780-10782.3): a public mandate to assess and monitor the quality of groundwater resources used for drinking-water supplies, and to increase the availability of information about groundwater quality to the public. The U.S. Geological Survey is the technical lead of the Priority Basin Project. Stewardship of California’s groundwater resources is a responsibility shared between well owners, communities, and the State. Participants and collaborators in the GAMA Program include Regional Water Quality Control Boards, Department of Water Resources, Department of Public Health, local and regional groundwater management entities, county and local water agencies, community groups, and private citizens. Well-owner participation in the GAMA Program is entirely voluntary.

  20. Monitoring Air Quality over China: Evaluation of the modeling system of the PANDA project

    Science.gov (United States)

    Bouarar, Idir; Katinka Petersen, Anna; Brasseur, Guy; Granier, Claire; Xie, Ying; Wang, Xuemei; Fan, Qi; Wang, Lili

    2015-04-01

    Air pollution has become a pressing problem in Asia and specifically in China due to rapid increase in anthropogenic emissions related to growth of China's economic activity and increasing demand for energy in the past decade. Observed levels of particulate matter and ozone regularly exceed World Health Organization (WHO) air quality guidelines in many parts of the country leading to increased risk of respiratory illnesses and other health problems. The EU-funded project PANDA aims to establish a team of European and Chinese scientists to monitor air pollution over China and elaborate air quality indicators in support of European and Chinese policies. PANDA combines state-of-the-art air pollution modeling with space and surface observations of chemical species to improve methods for monitoring air quality. The modeling system of the PANDA project follows a downscaling approach: global models such as MOZART and MACC system provide initial and boundary conditions to regional WRF-Chem and EMEP simulations over East Asia. WRF-Chem simulations at higher resolution (e.g. 20km) are then performed over a smaller domain covering East China and initial and boundary conditions from this run are used to perform simulations at a finer resolution (e.g. 5km) over specific megacities like Shanghai. Here we present results of model simulations for January and July 2010 performed during the first year of the project. We show an intercomparison of the global (MACC, EMEP) and regional (WRF-Chem) simulations and a comprehensive evaluation with satellite measurements (NO2, CO) and in-situ data (O3, CO, NOx, PM10 and PM2.5) at several surface stations. Using the WRF-Chem model, we demonstrate that model performance is influenced not only by the resolution (e.g. 60km, 20km) but also the emission inventories used (MACCity, HTAPv2), their resolution and diurnal variation, and the choice of initial and boundary conditions (e.g. MOZART, MACC analysis).

  1. The Walla Walla Basin Natural Production Monitoring and Evaluation Project : Progress Report, 1999-2002.

    Energy Technology Data Exchange (ETDEWEB)

    Contor, Craig R.; Sexton, Amy D.

    2003-06-02

    The Walla Walla Basin Natural Production Monitoring and Evaluation Project (WWNPME) was funded by Bonneville Power Administration (BPA) as directed by section 4(h) of the Pacific Northwest Electric Power Planning and Conservation Act of 1980 (P. L. 96-501). This project is in accordance with and pursuant to measures 4.2A, 4.3C.1, 7.1A.2, 7.1C.3, 7.1C.4 and 7.1D.2 of the Northwest Power Planning Council's (NPPC) Columbia River Basin Fish and Wildlife Program (NPPC 1994). Work was conducted by the Fisheries Program of the Confederated Tribes of the Umatilla Indian Reservation (CTUIR) under the Walla Walla Basin Natural Production Monitoring and Evaluation Project (WWNPME). Chapter One provides an overview of the entire report and how the objectives of each statement of work from 1999, 2000, 2001, and 2002 contract years are organized and reported. Chapter One also provides background information relevant to the aquatic resources of the Walla Walla River Basin. Objectives are outlined below for the statements of work for the 1999, 2000, 2001 and 2002 contract years. The same objectives were sometimes given different numbers in different years. Because this document is a synthesis of four years of reporting, we gave objectives letter designations and listed the objective number associated with the statement of work for each year. Some objectives were in all four work statements, while other objectives were in only one or two work statements. Each objective is discussed in a chapter. The chapter that reports activities and findings of each objective are listed with the objective below. Because data is often interrelated, aspects of some findings may be reported or discussed in more than one chapter. Specifics related to tasks, approaches, methods, results and discussion are addressed in the individual chapters.

  2. Environmental monitoring for the hot dry rock geothermal energy development project. Annual report, July 1975--June 1976

    Energy Technology Data Exchange (ETDEWEB)

    Pettitt, R.A. (comp.)

    1976-09-01

    The objectives of this environmental monitoring report are to provide a brief conceptual and historical summary of the Hot Dry Rock Geothermal Project, a brief overview of the environmental monitoring responsibilities and activities of the Los Alamos Scientific Laboratory, and descriptions of the studies, problems, and results obtained from the various monitoring programs. Included are descriptions of the work that has been done in three major monitoring areas: (1) water quality, both surface and subsurface; (2) seismicity, with a discussion of the monitoring strategy of regional, local, and close-in detection networks; and (3) climatology. The purpose of these programs is to record baseline data, define potential effects from the project activities, and determine and record any impacts that may occur.

  3. A framework for monitoring and evaluating carbon mitigation by farm forestry projects. Example of a demonstration project in Chiapas, Mexico

    Energy Technology Data Exchange (ETDEWEB)

    De Jong, B.H.J. [El Colegio de la Frontera Sur, Chiapas (Mexico); Tipper, R. [Institute of Ecology and Resource Management, University of Edinburgh, Edinburgh (United Kingdom); Taylor, J. [Union de Credito `Pajal Ya Kac Tic`, Chiapas (Mexico)

    1997-10-01

    In Mexico an estimated 4.5 x 10{sup 6} ha are available for farm forestry, while up to 6.1 x 10{sup 6} ha could be saved from deforestation by making shifting agriculture more productive and sustainable. Various farm forestry systems are technically, socially, and economically viable, including live fences, coffee with shade trees, plantations, tree enrichment of fallows, and taungya, with a C-sequestration potential varying from 17.6 to 176.3 Mg C ha{sup -1}. A self-reporting system with on-site spot checks is presented for the monitoring and evaluation (M and E), and will be tested in a farm forestry C-sequestration pilot project, to begin in Chiapas, Mexico, in 1997. The M and E procedure will facilitate the collection of field data at low cost, help ensure that the system continue to address the needs of farmers, and give farmers an understanding of the value of the service that they are providing. 4 figs., 3 tabs., 20 refs.

  4. MODELING OF THE DIVERSION CHANNEL CLOSURE FOR THE THIRD STAGE OF THE THREE GORGES PROJECT

    Institute of Scientific and Technical Information of China (English)

    Guangqian WANG; Baosheng WU; Junqiang XIA

    2004-01-01

    The closure of third stage diversion channel for the Three Gorges Dam is characterized by large closure discharge, large drop in water surface, and high gap velocity. 1D and 2D flow mathematical models were used in this paper to simulate the hydraulic conditions during the closure. The variation of discharge in the diversion channel and the drops in water surface shared by the upstream and downstream cofferdams were computed using the 1D model, and the detailed hydraulic patterns in the diversion channel were simulated using the 2D model. The computed results indicate that the designed closure scheme for discharge of 9,010 m3/s was feasible for construction, while the designed closure scheme for discharge of 12,200 m3/s was inapplicable.

  5. SHynergie: Development of a virtual project laboratory for monitoring hydraulic stimulations

    Science.gov (United States)

    Renner, Jörg; Friederich, Wolfgang; Meschke, Günther; Müller, Thomas; Steeb, Holger

    2016-04-01

    Hydraulic stimulations are the primary means of developing subsurface reservoirs regarding the extent of fluid transport in them. The associated creation or conditioning of a system of hydraulic conduits involves a range of hydraulic and mechanical processes but also chemical reactions, such as dissolution and precipitation, may affect the stimulation result on time scales as short as hours. In the light of the extent and complexity of these processes, the steering potential for the operator of a stimulation critically depends on the ability to integrate the maximum amount of site-specific information with profound process understanding and a large spectrum of experience. We report on the development of a virtual project laboratory for monitoring hydraulic stimulations within the project SHynergie (http://www.ruhr-uni-bochum.de/shynergie/). The concept of the laboratory envisioned product that constitutes a preparing and accompanying rather than post-processing instrument ultimately accessible to persons responsible for a project over a web-repository. The virtual laboratory consists of a data base, a toolbox, and a model-building environment. Entries in the data base are of two categories. On the one hand, selected mineral and rock properties are provided from the literature. On the other hand, project-specific entries of any format can be made that are assigned attributes regarding their use in a stimulation problem at hand. The toolbox is interactive and allows the user to perform calculations of effective properties and simulations of different types (e.g., wave propagation in a reservoir, hydraulic test). The model component is also hybrid. The laboratory provides a library of models reflecting a range of scenarios but also allows the user to develop a site-specific model constituting the basis for simulations. The laboratory offers the option to use its components following the typical workflow of a stimulation project. The toolbox incorporates simulation

  6. Emergency monitoring strategy and radiation measurements document of the NKS project emergency management and radiation monitoring in nuclear and radiological accidents (EMARAD)

    Energy Technology Data Exchange (ETDEWEB)

    Lahtinen, J. [Radiation and Nuclear Safety Authority (STUK) (Finland)

    2006-04-15

    This report is one of the deliverables of the NKS Project Emergency management and radiation monitoring in nuclear and radiological accidents (EMARAD) (20022005). The project and the overall results are briefly described in the NKS publication 'Emergency Management and Radiation Monitoring in Nuclear and Radiological Accidents. Summary Report on the NKS Project EMARAD' (NKS-137, April 2006). In a nuclear or radiological emergency, all radiation measurements must be performed efficiently and the results interpreted correctly in order to provide the decision-makers with adequate data needed in analysing the situation and carrying out countermeasures. Managing measurements in different situations in a proper way requires the existence of pre-prepared emergency monitoring strategies. Preparing a comprehensive yet versatile strategy is not an easy task to perform because there are lots of different factors that have to be taken into account. The primary objective of this study was to discuss the general problematics concerning emergency monitoring strategies and to describe a few important features of an efficient emergency monitoring system as well as factors affecting measurement activities in practise. Some information concerning the current situation in the Nordic countries has also been included. (au)

  7. Emergency monitoring strategy and radiation measurements document of the NKS project emergency management and radiation monitoring in nuclear and radiological accidents (EMARAD)

    Energy Technology Data Exchange (ETDEWEB)

    Lahtinen, J. [Radiation and Nuclear Safety Authority (STUK) (Finland)

    2006-04-15

    This report is one of the deliverables of the NKS Project Emergency management and radiation monitoring in nuclear and radiological accidents (EMARAD) (20022005). The project and the overall results are briefly described in the NKS publication 'Emergency Management and Radiation Monitoring in Nuclear and Radiological Accidents. Summary Report on the NKS Project EMARAD' (NKS-137, April 2006). In a nuclear or radiological emergency, all radiation measurements must be performed efficiently and the results interpreted correctly in order to provide the decision-makers with adequate data needed in analysing the situation and carrying out countermeasures. Managing measurements in different situations in a proper way requires the existence of pre-prepared emergency monitoring strategies. Preparing a comprehensive yet versatile strategy is not an easy task to perform because there are lots of different factors that have to be taken into account. The primary objective of this study was to discuss the general problematics concerning emergency monitoring strategies and to describe a few important features of an efficient emergency monitoring system as well as factors affecting measurement activities in practise. Some information concerning the current situation in the Nordic countries has also been included. (au)

  8. First results of the research project MIRAMAR, Innovative Methodologies for Coastal Environmental Monitoring and Analysis

    Science.gov (United States)

    Rovere, A.; Casella, E.; Vacchi, M.; Mucerino, L.; Pedroncini, A.; Ferrari, M.; Firpo, M.

    2013-12-01

    A large part of the Mediterranean coastlines are strongly affected by coastal erosion. This is mainly due to human impact, natural hazards and their mutual interaction. All along the Regione Liguria coastlines (Northwestern Mediterranean), significant problems of coastal erosion are reported since the '60s. In this study, we focus on the coastal area between Albenga and Savona, where dramatic coastal retreat of ~2 m y-1 has been inferred from comparison of historic maps and older aerial pictures. Beach monitoring is essential in order to understand the mechanisms of evolution of soft coasts, and the rates of erosion. Traditional beach monitoring techniques involve topographic and bathymetric surveys of the emerged and submerged beach, and/or aerial photos repeated in time and compared through geographical information systems. A major problem of this kind of approach is the high economic cost. This often leads to increase the time lag between successive monitoring campaigns to reduce survey costs, with the consequence of fragmenting the information available for coastal zone management. MIRAMar is a project funded by Regione Liguria through the PO CRO European Social Fund, and it has two main objectives: i) to study and develop an innovative technique, relatively low-cost, to monitor the evolution of the shoreline using low-altitude Unmanned Aerial Vehicle (UAV) photos; ii) to study the impact of different type of storm events on a vulnerable coastal tract subject to coastal erosion using also the data collected by the UAV instrument. To achieve these aims we use a drone with its hardware and software suit, traditional survey techniques (bathymetric surveys, topographic GPS surveys and GIS techniques) and we implement a numerical modeling chain (coupling hydrodynamic, wave and sand transport modules) in order to study the impact of different type of storm events on a vulnerable coastal tract subject to coastal erosion. Aerial picture of one of the beaches studied

  9. Spreadsheet based methodology to assess offshore wind capacity factors in project planning stage

    Energy Technology Data Exchange (ETDEWEB)

    Madariaga, Ander; Martin, Jose Luis; Martinez de Alegria, Inigo [University of the Basque Country (UPV/EHU), Bilbao (Spain). Engineering Faculty; Ceballos, Salvador [Tecnalia Research and Innovation, Parque Tecnologico de Bizkaia, Derio (Spain); Anaya-Lara, Olimpo [Strathclyde Univ., Glasgow (United Kingdom). Inst. for Energy and Environment

    2012-07-01

    This paper presents a methodology to assess the effective capacity factor of an offshore wind power plant (OWPP). The electric power losses in all the systems that make up the wind farm are considered: the offshore wind turbines (OWTs), the collector system (CS) and the transmission system (TS). Other relevant issues such as the wake effect and the unavailability of the systems that make up the windfarm are also taken into account. The formulation of the methodology is fully analytic, with no simulation procedures for the evaluation of the electric power losses. A novel proposal to assess the losses in long submarine three-core cross linked polyethylene (XLPE) cables is presented in detail. Due to its analytic structure, the methodology can be implemented either in algorithmic form or in a spreadsheet, enabling to evaluate OWPPs electric topologies in an agile way. It is aimed at engineering researchers and project planning engineers involved in the offshore wind industry. (orig.)

  10. Monitoring Based Commissioning: Benchmarking Analysis of 24 UC/CSU/IOU Projects

    Energy Technology Data Exchange (ETDEWEB)

    Mills, Evan; Mathew, Paul

    2009-04-01

    Buildings rarely perform as intended, resulting in energy use that is higher than anticipated. Building commissioning has emerged as a strategy for remedying this problem in non-residential buildings. Complementing traditional hardware-based energy savings strategies, commissioning is a 'soft' process of verifying performance and design intent and correcting deficiencies. Through an evaluation of a series of field projects, this report explores the efficacy of an emerging refinement of this practice, known as monitoring-based commissioning (MBCx). MBCx can also be thought of as monitoring-enhanced building operation that incorporates three components: (1) Permanent energy information systems (EIS) and diagnostic tools at the whole-building and sub-system level; (2) Retro-commissioning based on the information from these tools and savings accounting emphasizing measurement as opposed to estimation or assumptions; and (3) On-going commissioning to ensure efficient building operations and measurement-based savings accounting. MBCx is thus a measurement-based paradigm which affords improved risk-management by identifying problems and opportunities that are missed with periodic commissioning. The analysis presented in this report is based on in-depth benchmarking of a portfolio of MBCx energy savings for 24 buildings located throughout the University of California and California State University systems. In the course of the analysis, we developed a quality-control/quality-assurance process for gathering and evaluating raw data from project sites and then selected a number of metrics to use for project benchmarking and evaluation, including appropriate normalizations for weather and climate, accounting for variations in central plant performance, and consideration of differences in building types. We performed a cost-benefit analysis of the resulting dataset, and provided comparisons to projects from a larger commissioning 'Meta-analysis' database. A

  11. 2012 Groundwater Monitoring Report Project Shoal Area Subsurface Corrective Action Unit 447

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-03-01

    The Project Shoal Area (PSA) in Nevada was the site of a 12-kiloton underground nuclear test in 1963. Although the surface of the site has been remediated, investigation of groundwater contamination resulting from the test is still in the corrective action process. Annual sampling and hydraulic head monitoring are conducted at the site as part of the subsurface corrective action strategy. Analytical results from the 2012 monitoring are consistent with those of the previous years, with tritium detected only in well HC-4. The tritium concentration in groundwater from well HC-4 remains far below the U.S. Environmental Protection Agency-established maximum contaminant level of 20,000 picocuries per liter. Concentrations of total uranium and gross alpha were also detected during this monitoring period, with uranium accounting for nearly all the gross alpha activity. The total uranium concentrations obtained from this monitoring period were consistent with previous results and reflect a slightly elevated natural uranium concentration, consistent with the mineralized geologic terrain. Isotopic ratios of uranium also indicate a natural source of uranium in groundwater, as opposed to a nuclear-test-related source. Water level trends obtained from the 2012 water level data were consistent with those of previous years. The corrective action strategy for the PSA is currently focused on revising the site conceptual model (SCM) and evaluating the adequacy of the current monitoring well network. Some aspects of the SCM are known; however, two major concerns are the uncertainty in the groundwater flow direction and the cause of rising water levels in site wells west of the shear zone. Water levels have been rising in the site wells west of the shear zone since the first hydrologic characterization wells were installed in 1996. While water levels in wells west of the shear zone continue to rise, the rate of increase is less than in previous years. The SCM will be revised, and an

  12. Research and development program in reactor diagnostics and monitoring with neutron noise methods. Stage 7. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Pazsit, I.; Demaziere, C.; Arzhanov, V. [Chalmers Univ. of Technology, Goeteborg (Sweden). Department of Reactor Physics; Garis, N.S. [Swedish Nuclear Power Inspectorate, Stockholm (Sweden)

    2001-08-01

    This report constitutes stage 7 of a long-term research and development program concerning the development of diagnostics and monitoring methods for nuclear reactors. A proposal for the continuation of this program in stage 8 is also given at the end of the report. In stage 6, the basic principles of a 3-D fully coupled neutronic/thermal-hydraulic simulator in the frequency domain were presented. The neutronic model relied on the two-group diffusion approximation, whereas the thermal-hydraulic algorithms relied on the so called 'lumped' model. The key element of this simulator was that only the static data were required which could be obtained from the Studsvik Scandpower CASMO-4/TABLES-3/ SIMULATE-3 code package. The simulator was developed with this underlying idea, which means that the calculation of the static fluxes and the eigenvalue were avoided. Depending on what kind of spatial discretization scheme which is used in the noise simulator to calculate the 'leakage' noise, it is not granted that the system remains critical by using the group constants supplied by SIMULATE. Nevertheless, when the system is critical, the balance equations should be fulfilled in all nodes with respect to the discretization scheme used. In concrete terms, the calculation of the static fluxes and eigenvalue can be avoided if the system is brought back to criticality by modifying the cross-sections so that the balance equations are always fulfilled with the chosen spatial discretization scheme. This approach was used in this study with the finite difference scheme. As pointed out in stage 6, the finite difference scheme is relatively inefficient compared to finite elements or nodal methods, but on the other hand it is rather easy to implement. These two more sophisticated schemes are planned to be investigated at a later stage, but for the time being the simulator relying on the finite difference scheme was improved as much as possible so that a 2-D entirely

  13. On-line condition monitoring systems for high voltage circuit breakers : a collaborative research project 1997-2001

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    A three year field project was initiated to review and evaluate the state of the art in on-line conditioning monitoring technology for a high voltage (240 kV SF6) circuit breaker located at Dorsey Converter Station. The ELF breaker is a three independent pole design which allows for three separate monitoring systems. This project involved the installation of a different type of monitoring system on each phase and incorporated many types of transducers. Each monitoring system measured the same basic parameters including contact travel, 'a' and 'b' auxiliary contacts, phase currents, coil currents, heater and pump current, plus SF6/CF4 pressure and temperature. Over the entire monitoring period the breaker was operated over 700 times at rated voltage and an additional 300 times during maintenance. Temperature conditions ranged from -35 to +30 degrees C. The use of on-line monitoring provided many valuable results and enhanced the knowledge base for the apparatus under the test. It was determined that on-line monitoring of HV circuit breakers has potential, but installation has to be considered carefully. Monitoring systems can offer improvement in the understanding of how circuit breakers work and provide input into RCM programs. However, monitoring systems themselves are subject to failure and require maintenance and attention. 2 refs., 2 tabs., 7 figs.

  14. GULF OF MEXICO SEAFLOOR STABILITY AND GAS HYDRATE MONITORING STATION PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    J. Robert Woolsey; Thomas M. McGee; Robin C. Buchannon

    2004-11-01

    The gas hydrates research Consortium (HRC), established and administered at the University if Mississippi's Center for Marine Research and Environmental Technology (CMRET) has been active on many fronts in FY 03. Extension of the original contract through March 2004, has allowed completion of many projects that were incomplete at the end of the original project period due, primarily, to severe weather and difficulties in rescheduling test cruises. The primary objective of the Consortium, to design and emplace a remote sea floor station for the monitoring of gas hydrates in the Gulf of Mexico by the year 2005 remains intact. However, the possibility of levering HRC research off of the Joint Industries Program (JIP) became a possibility that has demanded reevaluation of some of the fundamental assumptions of the station format. These provisions are discussed in Appendix A. Landmark achievements of FY03 include: (1) Continuation of Consortium development with new researchers and additional areas of research contribution being incorporated into the project. During this period, NOAA's National Undersea Research Program's (NURP) National Institute for Undersea Science and Technology (NIUST) became a Consortium funding partner, joining DOE and Minerals Management Service (MMS); (2) Very successful annual and semiannual meetings in Oxford Mississippi in February and September, 2003; (3) Collection of piston cores from MC798 in support of the effort to evaluate the site for possible monitoring station installation; (4) Completion of the site evaluation effort including reports of all localities in the northern Gulf of Mexico where hydrates have been documented or are strongly suspected to exist on the sea floor or in the shallow subsurface; (5) Collection and preliminary evaluation of vent gases and core samples of hydrate from sites in Green Canyon and Mississippi Canyon, northern Gulf of Mexico; (6) Monitoring of gas activity on the sea floor, acoustically

  15. Markov Chain Monte Carlo simulation for projection of end stage renal disease patients in Greece.

    Science.gov (United States)

    Rodina-Theocharaki, A; Bliznakova, K; Pallikarakis, N

    2012-07-01

    End stage renal disease (ESRD) treatment methods are considered to be among the most expensive procedures for chronic conditions worldwide which also have severe impact on patients' quality of life. During the last decade, Greece has been among the countries with the highest incidence and prevalence, while at the same time with the lowest kidney transplantation rates. Predicting future patients' number on Renal Replacement Therapy (RRT) is essential for health care providers in order to achieve more effective resource management. In this study a Markov Chain Monte Carlo (MCMC) simulation is presented for predicting the future number of ESRD patients for the period 2009-2020 in Greece. The MCMC model comprises Monte Carlo sampling techniques applied on probability distributions of the constructed Markov Chain. The model predicts that there will be 15,147 prevalent patients on RRT in Greece by 2020. Additionally, a cost-effectiveness analysis was performed on a scenario of gradually reducing the hemodialysis patients in favor of increasing the transplantation number by 2020. The proposed scenario showed net savings of 86.54 million Euros for the period 2009-2020 compared to the base-case prediction.

  16. Entrepreneurs’ Expectations and Students’ Competencies According to the First Stage of the Synergy Project Evaluation

    Directory of Open Access Journals (Sweden)

    Lukasz Wiechetek

    2014-06-01

    Full Text Available The article presents the results of a research on students’ competencies selfesteem. The research was conducted in the years 2009–2012, on a sample of 1,831 students, under the project called ‘SYNERGY – MCSU Faculty of Economics students’ competencies development by gaining practical knowledge.’ co-financed by the European Union from the European Social Fund. The purpose of the research was to pinpoint the areas of competencies that are considered to be essential for business and determine the level of students’ self-esteem in the identified areas. The main objective of the article is to show the competencies that are desirable from the business point of view, but are, in the opinion of the students, at a rather low level and require special attention and development. The paper presents the key findings of the study: the lowest self-esteem level was observed in the area of knowledge needed by the employers, the highest in the attitudes wanted by the labor market. Positive relationship was found between the level of competence self-esteem and the respondents’ year of study.

  17. HIE ISOLDE Alignment and monitoring system technical design and project status

    CERN Document Server

    Gayde, J C; Kautzmann, G; Leclercq, Y; Waniorek, S; Williams, L

    2012-01-01

    In the frame of the HIE ISOLDE project most of the existing ISOLDE REX line will be replaced by a superconducting linac in order to upgrade the energy and intensity of the REX ISOLDE facility at CERN. Beam-physics simulations show that the optimum linac working conditions are obtained when the main axes of the active components, RF cavities and solenoid placed inside the cryostats, are aligned and permanently monitored on the REX Nominal Beam Line (NBL) within a precision of 0.3 mm for the cavities and 0.15 mm for the solenoids at one sigma level along directions perpendicular to the beam axis. This paper presents the proposed adjustment and alignment system based on opto-electronic sensors, optics and precise mechanic elements which are used, for some of them, in various non-standard environmental conditions such as high vacuum, cryogenic temperatures.

  18. Monitoring nuclear reactors with anti-neutrino detectors: the ANGRA project

    Energy Technology Data Exchange (ETDEWEB)

    Chimenti, Pietro; Leigui, Marcelo Augusto [UFABC - Universidade Federal do ABC. Rua Santa Adelia, 166. Bairro Bangu. Santo Andre - SP (Brazil); Anjos, Joao; Azzi, Gabriel; Rafael, Gama; Ademarlaudo, Barbosa; Lima, Herman; VAZ, Mario; Villar, Arthur [Centro Brasileiro de Pesquisas Fisicas - CBPF, Rua Dr. Xavier Sigaud, 150, Urca, Rio de Janeiro, RJ - 22290-180 (Brazil); Gonzales, Luis Fernando; Bezerra, Thiago; Kemp, Ernesto [Unicamp, State University of Campinas, Cidade Universitaria ' Zeferino Vaz' , Barao Geraldo - Campinas, Sao Paulo (Brazil); Nunokawa, Hiroshi [Department of Physics, Pontifical Catholic University - PUC, Rua Marques de Sao Vicente, 225, 22451-900 Gavea - Rio de Janeiro - RJ (Brazil); Guedes, Germano; Faria, Paulo Cesar [Universidade Estadual de Feira de Santana - UEFS, Avenida Transnordestina, Novo Horizonte (Brazil); Pepe, Iuri [Universidade Federal da Bahia - UFBA (Brazil)

    2010-07-01

    We describe the status of the ANGRA Project, aimed at developing an anti-neutrino detector for monitoring nuclear reactors. Indeed the detection of anti-neutrinos provides a unique handle for non-invasive measurements of the nuclear fuel. This kind of measurements are of deep interest for developing new safeguards tools which may help in nuclear non-proliferation programs. The ANGRA experiment, placed at about 30 m from the core of the 4 GW Brazilian nuclear power reactor ANGRA II, is based on a water Cherenkov detector with about one ton target mass. A few thousand antineutrino interactions per day are expected. The latest results from simulations and the status of the construction are presented. (authors)

  19. SAR interferometry monitoring along the ancient Rome City Walls -the PROTHEGO project case study

    Science.gov (United States)

    Carta, Cristina; Cimino, Maria gabriella; Leoni, Gabriele; Marcelli, Marina; Margottini, Claudio; Spizzichino, Daniele

    2017-04-01

    Led by the Italian Institute for Environmental Protection and Research, in collaboration with NERC British Geological Survey, Geological and Mining Institute of Spain, University of Milano-Bicocca and Cyprus University of Technology, the PROTHEGO project, co-funded in the framework of JPI on Cultural Heritage EU program (2015-2018), brings an innovative contribution towards the analysis of geo-hazards in areas of cultural heritage in Europe. The project apply InSAR techniques to monitor monuments and sites that are potentially unstable due to natural geo-hazard. After the remote sensing investigation, detailed geological interpretation, hazard analysis, local-scale monitoring, advanced modeling and field surveying for some case studies is implemented. The selected case studies are: the Alhambra in Granada (ES); the Choirokoitia village (CY); the Derwent Valley Mills (UK); the Pompei archaeological site and Historical centre of Rome (IT). In this work, in particular, we will focus on ground deformation measurements (obtained by satellite SAR Interferometry) and on their interpretation with respect to the ancient Rome City Walls. The research activities carried out jointly with the Superintendence's technicians, foresee the implementation of a dedicated web GIS platform as a final repository for data storage and spatial data elaboration. The entire circuit of the ancient city walls (both Mura Aureliane and Mura Gianicolensi), was digitalized and georeferenced. All the elements (towers, gates and wall segments) were drawn and collected in order to produce a map of elements at risk. A detailed historical analysis (during the last twenty years) of the ground and structural deformations were performed. A specific data sheet of ruptures was created and fulfilled in order to produce a geographic inventory of past damage. This data sheet contains the following attributes: triggering data; typology of damage; dimension, triggering mechanism; presence of restoration works

  20. Pilot CCS project in Indonesia "Gundih CCS project": Geological and geophysical surveys for site selection and monitoring

    Science.gov (United States)

    Tsuji, Takeshi; Matsuoka, Toshifumi; Takahashi, Toru; Kitamura, Keigo; Onishi, Kyosuke; Yamada, Yasuhiro; Rachmat Sule, Mohammad; Kadir, Wawan Gunawan A.; Widarto, Djedi S.; Sebayang, Rio I.; Prasetyo, Agung; Priyono, Awali; Widianto, Eko; Sapiie, Benyamin

    2013-04-01

    A pilot CCS project in Indonesia will be implemented in Gundih area, Central Java Province. The Gundih area is a gas field, and gas is ready to be produced by Pertamina EP. The CO2 content within the produced gas is more than 20% in the Gundih field, so that CO2 injection near the gas production well could be effective way to avoid abundant CO2 emission. Before implementing CO2 injection, the reservoir for CO2 injection must be characterized carefully by conducting subsurface characterization and evaluation, in order to make sure that the reservoir is suitable for CCS. Here we report preliminary results of site surveys for the determination of CO2 injection site in the Gundih area. Subsurface structures imaged on seismic reflection profiles indicate that the Ngrayong formation is one of the candidates for CO2 injection. The lithology of the Ngrayong formation is sandstone, and the depth of the formation is ~1 km in the Gundih area. Since we could not find large-scale structural closure (i.e., anticline) for the Ngrayong formation, we need to consider residual trapping. To reveal hydrological properties (e.g., permeability) of the Ngrayong formation, we obtained rock samples from the outcrop of the Ngrayong formation. Using the laboratory-derived hydrological properties and subsurface structures extracted from seismic data (e.g., geometry of the Ngrayong formation), we will apply reservoir simulation in order to determine CO2 injection site. To design the geophysical monitoring survey (e.g., receiver and source position in time-lapse seismic survey), furthermore, we conduct simulation study for the constructed geological model and estimate elastic and electric responses associated with CO2 injection.

  1. Project of a Near-Real-Time Sismo-acoustic Submarine Station for offshore monitoring (NRTSSS)

    Science.gov (United States)

    D'Anna, G.; Calore, D.; Mangano, G.; D'Alessandro, A.; Favali, P.

    2011-12-01

    The INGV seismic network ensures reliable and continuous monitoring of the Italian territory. However, the peculiarity of the Italian peninsula, characterised by an intense offshore geodynamic and seismic activity, requires the extension of the seismic monitoring to the sea. The aim of this project is: - to identify bottleneck is related to the construction, installation and use of underwater seismic station; - to define the most appropriate and low-cost architecture to guarantee the minimum functionality required for a seismic station. In order to obtain reliable seafloor seismic signals integrated to land-based network, the requirements to be fulfill are: - an acceptable coupling with the seabed; - the orientation of the components with respect to the magnetic North and to the verticality; - the correct time stamp of the data; - the data transfer to the land for the integration. Currently, the optimal solution for offshore seismic station is a cable connection to power and real-time data transfer, like the case of Western Ionian Sea cabled observatory, one of the operative node of the EMSO research infrastructure (European Multidisciplinary Seafloor and water column Observatory, http://emso-eu.org). But in the Mediterranean many seismic areas are located a few tens-hundreds of miles from the coast and cabled solutions are not feasible essentially for economic reasons. For this kind of installations EMSO research infrastructure foresees no-cabled solution, that requires a surface buoy deployed in the vicinity seafloor modules.This project plans to develop a surface buoy equipped with autonomous power supply system to power also the seafloor platforms and two-way communication system enabling the data transfer through latest generation of broadband radio communication or satellite link (Fig. 1). All the components of the prototype system are described.

  2. Land change monitoring, assessment, and projection (LCMAP) revolutionizes land cover and land change research

    Science.gov (United States)

    Young, Steven

    2017-05-02

    When nature and humanity change Earth’s landscapes - through flood or fire, public policy, natural resources management, or economic development - the results are often dramatic and lasting.Wildfires can reshape ecosystems. Hurricanes with names like Sandy or Katrina will howl for days while altering the landscape for years. One growing season in the evolution of drought-resistant genetics can transform semiarid landscapes into farm fields.In the past, valuable land cover maps created for understanding the effects of those events - whether changes in wildlife habitat, water-quality impacts, or the role land use and land cover play in affecting weather and climate - came out at best every 5 to 7 years. Those high quality, high resolution maps were good, but users always craved more: even higher quality data, additional land cover and land change variables, more detailed legends, and most importantly, more frequent land change information.Now a bold new initiative called Land Change Monitoring, Assessment, and Projection (LCMAP) promises to fulfill that demand.Developed at the U.S. Geological Survey (USGS) Earth Resources Observation and Science (EROS) Center in Sioux Falls, South Dakota, LCMAP provides definitive, timely information on how, why, and where the planet is changing. LCMAP’s continuous monitoring process can detect changes as they happen every day that Landsat satellites acquire clear observations. The result will be to place near real-time information in the hands of land and resource managers who need to understand the effects these changes have on landscapes.

  3. Methodology for locale-scale monitoring for the PROTHEGO project: the Choirokoitia case study

    Science.gov (United States)

    Themistocleous, Kyriacos; Agapiou, Athos; Cuca, Branka; Danezis, Chris; Cigna, Francesca; Margottini, Claudio; Spizzichino, Daniele

    2016-10-01

    PROTHEGO (PROTection of European Cultural HEritage from GeO-hazards) is a collaborative research project funded in the framework of the Joint Programming Initiative on Cultural Heritage and Global Change (JPICH) - Heritage Plus in 2015-2018 (www.prothego.eu). PROTHEGO aims to make an innovative contribution towards the analysis of geohazards in areas of cultural heritage, and uses novel space technology based on radar interferometry (InSAR) to retrieve information on ground stability and motion in the 400+ UNESCO's World Heritage List monuments and sites of Europe. InSAR can be used to measure micro-movements to identify geo-hazards. In order to verify the InSAR image data, field and close range measurements are necessary. This paper presents the methodology for local-scale monitoring of the Choirokoitia study site in Cyprus, inscribed in the UNESCO World Heritage List, and part of the demonstration sites of PROTHEGO. Various field and remote sensing methods will be exploited for the local-scale monitoring, static GNSS, total station, leveling, laser scanning and UAV and compared with the Persistent Scatterer Interferometry results. The in-situ measurements will be taken systematically in order to document any changes and geo-hazards that affect standing archaeological remains. In addition, ground truth from in-situ visits will provide feedback related to the classification results of urban expansion and land use change maps. Available archival and current optical satellite images will be used to calibrate and identify the level of risk at the Cyprus case study site. The ground based geotechnical monitoring will be compared and validated with InSAR data to evaluate cultural heritage sites deformation trend and to understand its behaviour over the last two decades.

  4. Visualizing Earth Science Data for Environmental Monitoring and Decision Support in Mesoamerica: The SERVIR Project

    Science.gov (United States)

    Hardin, D.; Graves, S.; Sever, T.; Irwin, D.

    2005-05-01

    In 2002 and 2003 NASA, the World Bank and the United States Agency for International Development (USAID) joined with the Central American Commission for Environment and Development (CCAD) to develop an advanced decision support system for Mesoamerica (named SERVIR). Mesoamerica - composed of the seven Central American countries and the five southernmost states of Mexico - makes up only a small fraction of the world's land surface. However, the region is home to approximately eight percent of the planet's biodiversity (14 biosphere reserves, 31 Ramsar sites, 8 world heritage sites, 589 protected areas) and 45 million people including more than 50 different ethnic groups. Mesoamerica's biological and cultural diversity are severely threatened by human impact and natural disasters including extensive deforestation, illegal logging, water pollution, slash and burn agriculture, earthquakes, hurricanes, drought, and volcanic eruption. NASA Marshall Space Flight Center (NASA/MSFC), together with the University of Alabama in Huntsville (UAH) and the SERVIR partners are developing state-of-the-art decision support tools for environmental monitoring as well as disaster prevention and mitigation in Mesoamerica. These partners are contributing expertise in space-based observation with information management technologies and intimate knowledge of local ecosystems to create a system that is being used by scientists, educators, and policy makers to monitor and forecast ecological changes, respond to natural disasters, and better understand both natural and human induced effects. The decision support and environmental monitoring data products are typically formatted as conventional two-dimensional, static and animated imagery. However, in addition to conventional data products and as a major portion of our research, we are employing commercial applications that generate three-dimensional interactive visualizations that allow data products to be viewed from multiple angles and at

  5. Chicago Clean Air, Clean Water Project: Environmental Monitoring for a Healthy, Sustainable Urban Future

    Energy Technology Data Exchange (ETDEWEB)

    none, none; Tuchman, Nancy [Institute of Environmental Sustainability (IES), Chicago, IL (United States)

    2015-11-11

    The U.S. Department of Energy awarded Loyola University Chicago and the Institute of Environmental Sustainability (IES) $486,000.00 for the proposal entitled “Chicago clean air, clean water project: Environmental monitoring for a healthy, sustainable urban future.” The project supported the purchase of analytical instruments for the development of an environmental analytical laboratory. The analytical laboratory is designed to support the testing of field water and soil samples for nutrients, industrial pollutants, heavy metals, and agricultural toxins, with special emphasis on testing Chicago regional soils and water affected by coal-based industry. Since the award was made in 2010, the IES has been launched (fall 2013), and the IES acquired a new state-of-the-art research and education facility on Loyola University Chicago’s Lakeshore campus. Two labs were included in the research and education facility. The second floor lab is the Ecology Laboratory where lab experiments and analyses are conducted on soil, plant, and water samples. The third floor lab is the Environmental Toxicology Lab where lab experiments on environmental toxins are conducted, as well as analytical tests conducted on water, soil, and plants. On the south end of the Environmental Toxicology Lab is the analytical instrumentation collection purchased from the present DOE grant, which is overseen by a full time Analytical Chemist (hired January 2016), who maintains the instruments, conducts analyses on samples, and helps to train faculty and undergraduate and graduate student researchers.

  6. Monitoring Liquid Argon Time Projection Chambers With A Raspberry Pi Camera

    Science.gov (United States)

    Patteson, Crystal

    2016-03-01

    The MicroBooNE detector is the first of three liquid argon (LAr) time projection chambers (TPCs) that are central to the short-baseline neutrino program at Fermilab. These chambers consist of thousands of stainless steel or beryllium-copper sense wires that detect ionization electrons produced when neutrinos interact with liquid argon nuclei inside the detector. The wires are several hundred microns in diameter to several meters in length. The construction of such LAr TPCs often takes place in an assembly hall, which is different from the detector hall where the experiment will operate, as was the case with MicroBooNE. Since in situ access to the chamber and its wires in the beamline enclosure can be limited, we investigate the possibility of using a Raspberry Pi single-board computer connected to a low-cost camera installed inside the cryostat as a cost-efficient way to verify the integrity of the wires after transport. We also highlight other benefits of this monitoring device implemented in MicroBooNE, including detector hall surveillance and verification of the status of LED indicators on detector electronics. The author would like to thank Dr. Matthew Toups for his encouragement and guidance on this research project.

  7. Overview of the IEA GHG Weyburn-Midale CO{sub 2} monitoring and storage project

    Energy Technology Data Exchange (ETDEWEB)

    Mourits, Frank [Natural Resources Canada (Canada)

    2008-07-15

    In this presentation it is explained what the Weyburn-Midale project consists of; it is also spoken on the operation for the enhanced oil recovery of Encana Weyburn and Apache Midale Commercial; an overview and results are given of phase I (2000-2004) of the Weyburn project of monitoring and CO{sub 2} storage of greenhouse effect gases of the International Energy Agency; Characteristics and statistics of operation of the oil fields Weyburn and Midale, and how is it that with CO{sub 2} and recycled water the oil is recovered?. [Spanish] En esta presentacion se explica en que consiste el proyecto Weyburn-Midale; se habla tambien sobre la operacion para la recuperacion mejorada de petroleo de Encana Weyburn y Apache Midale Commercial; se da una vision general y resultados de la fase I (2000-2004) del proyecto Weyburn de monitoreo y almacenamiento de CO{sub 2} gases de efecto invernadero de la Agencia Internacional de Energia; Caracteristicas y estadisticas de operacion de los yacimientos petroliferos Weyburn y Midale, y como es que con el CO{sub 2} y agua reciclada se recupera el petroleo?.

  8. Global Radiological Source Sorting, Tracking, and Monitoring Project: Phase I Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Walker, Randy M [ORNL; Hill, David E [ORNL; Gorman, Bryan L [ORNL

    2010-09-01

    As a proof of concept tested in an operational context, the Global Radiological Source Sorting, Tracking, and Monitoring (GRadSSTraM) Project successfully demonstrated that radio frequency identification (RFID) and Web 2.0* technologies can be deployed to track controlled shipments between the United States and the European Union. Between November 2009 and May 2010, a total of 19 shipments were successfully shipped from Oak Ridge National Laboratory (ORNL) by the U.S. Postal Service (USPS) and tracked to their delivery at England's National Physical Laboratory (NPL) by the United Kingdom Royal Mail. However, the project can only be viewed as a qualified success as notable shortcomings were observed. Although the origin and terminus of all RFID-enabled shipments were recorded and no shipments were lost, not all the waypoints between ORNL and NPL were incorporated into the pilot. Given limited resources, the project team was able to install RFID listeners/actuators at three waypoints between the two endpoints. Although it is likely that all shipments followed the same route between ORNL and NPL, it cannot be determined beyond question that all 19 shipments were routed on identical itineraries past the same three waypoints. The pilot also raises the distinct possibility that unattended RFID tracking alone, without positive confirmation that a tagged item has been properly recorded by an RFID reader, does not meet a rigorous standard for shipping controlled items. Indeed, the proof of concept test strongly suggests that a multifaceted approach to tracking may be called for, including tracking methods that are capable of reading and accepting multiple inputs for individual items [e.g., carrier-provided tracking numbers, Universal Product Codes (UPCs), and RFID tags]. For controlled items, another apparent requirement is a confirmation feature, human or otherwise, which can certify that an item's RFID tag, UPC, or tracking number has been recorded.

  9. Research and Development Program in Reactor Diagnostics and Monitoring with Neutron Noise Methods. Stage 11 and 12. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Sunde, C.; Pazsit, I.; Demaziere, C.; Dahl, O.; Mileshina, L. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Nuclear Engineering

    2006-06-15

    This report describes the results obtained during Stage 11 and 12 of a long-term research and development program concerning the development of diagnostics and monitoring methods for nuclear reactors. The long-term goals are elaborated in more detail in e.g. the Final Reports of stage 1 and 2 (SKI Report 95:14 and 96:50). Higher order eigenfunctions and eigenvalues of the diffusion equation, describing a static core, have lost their significance when doing calculations in realistic systems, since there are usually made by nodal methods or other direct numerical techniques. However, there are situations when knowledge of the higher order modes is still useful. Such case is the separation of the global and regional flux oscillations in the case of BWR instability. Another case is the investigation of the stability properties of large inhomogeneous cores, which is usually quantified with the so-called eigenvalue separation, ES=1/k{sub 1} - 1/k{sub 0} where k{sub 0} and k{sub 1}, are the fundamental and first higher order eigenvalues, respectively. Numerical codes used for ICMF calculations usually do not have the option of calculating the higher order eigenvalues and eigenfunctions. In idealised systems, these can be calculated with semi-analytical methods. In order to get insight into the characteristics of the higher order eigenmodes of the neutron flux and the adjoint, these were calculated in a reflected homogeneous system with two-group theory. The adjoint eigenmodes are necessary if an orthogonality property needs to be used, such as the separation of the modes from a flux shape which is a sum of several eigenmodes. At the same time, the so-called numerical noise simulator, developed at the Dept., was extended such that it became suitable for the calculation of the higher order eigenmodes, both direct and adjoint ones. This simulator can treat real inhomogeneous cores, with an input deck compatible with that of SIMULATE. The simulator was used to calculate the

  10. Study on Cost Control of Garden Engineering Project During Design Stage%园林工程项目设计阶段造价控制研究

    Institute of Scientific and Technical Information of China (English)

    李雅文; 汪霞

    2014-01-01

    The paper analyzes the current situation of garden project design stage cost control ,and put forward the effective measures and methods of cost control during the design stage.%分析了园林工程设计阶段造价控制面临的问题和现状,提出设计阶段造价控制的有效措施和方法。

  11. A multi-disciplinary approach for sea water quality monitoring: the IOSMOS project

    Science.gov (United States)

    Lacava, Teodosio; Ciancia, Emanuele; Coviello, Irina; Daraio, Maria; Paciello, Rossana; Pergola, Nicola; Pignatti, Stefano; Santini, Federico; Tramutoli, Valerio; Vallianatos, Filippos

    2013-04-01

    Coastal zones are complex and dynamic ecosystems which represent one of the most productive areas of the marine environment. They are an important economic resource for human populations: they provide food, energy as well as a lot of commerce and recreation activities. The strong anthropization, the irrational exploitation of resources and the climate changes are causing a strong modification of the coastal areas, representing a continuous threat to the biodiversity of these areas. This is why coastal zones deserve the developing and implementing of a monitoring system able to guarantee their consistent and reliable control as well as to timely identify any sign of degradation. Water quality is an important indicator of the health of coastal ecosystem. Remote sensing data can give relevant information in this framework, offering the capability to provide the spatial distribution of water constituents over large spatial areas with high temporal rates and relatively low costs. In particular Ocean Color (OC) satellite instruments furnish information both on sea surface optical variables (e.g. upwelling normalized water-leaving radiances) and on bio-optical parameters such as chlorophyll-a (as a proxy of phytoplankton), suspended materials and dissolved organic matter. A study of these parameters and of their evolution in the space-time domain may provide useful information on the overall quality of the sea water for a specific area, offering, in addition the reference behaviors necessary for identifying significant changes (possibly induced by anthropogenic pressure) in the coastal environment. In this context main aim of IOSMOS (IOnian Sea water quality MOnitoring by Satellite data) - a Project for European Transnational Cooperation co financed by the Operational Programme ERDF Basilicata 2007-2013 - is the development of advanced and exportable satellite products for measuring the above mentioned coastal water parameters as well as to timely identify short

  12. Field experience with a novel pipe protection and monitoring system for large offshore pipeline construction projects

    Energy Technology Data Exchange (ETDEWEB)

    Magerstaedt, Michael; Blitz, Gunther [ROSEN Swiss AG, Stans (Switzerland); Sabido, Carlos E. [ROSEN Technology and Research Center, Lingen (Germany)

    2012-07-01

    For pipe joints stored during large-scale offshore pipeline construction projects, corrosion protection as well as protection from physical damage of pipelines is very important. Integrity Management does not just start with the operation of a pipeline. In the past, with the much lower risks and cost at stake in on shore constriction, this factor was often overlooked. Sometimes, newly laid pipelines failed upon hydrostatic testing or even during operation. Causes were corrosion or damage the pipe joints took before pipeline laying. For offshore projects, the cost and consequences associated with such failures are orders of magnitude higher and must be avoided by all means. Within six months from the conception of the idea, a system was developed and deployed that protected (and in part still protects) a large number of pipe joints used in a European offshore gas pipeline project more than 2000 km. The pipe joints were physically protected from corrosion, interior contamination, and condensation. At the same time, the system provided real-time monitoring of more than 100'000 pipe joints stored at 5 storage yards distributed over 3 countries with distances of more than 1200 km apart from each other. Every single joint was identified with its location and status at every time during the storage period. Any third-party interference was transmitted to a central control room in real time as well. Protection of the pipe joints was provided vs.: corrosion of pipe joint end cutbacks exposed to the maritime climate for up to 2 years; contamination of the pipe interior by: foreign material, dirt, water, ice, animals. Third party damage to the pipe joints; damage to the protection system or to the transmission network; fire; theft of pipe joints or other equipment. System features were: modular pipe caps that, protect the pipe interior, cover both inner and outer cutback, allow ventilation of the pipe interior, continuously monitor each pipe joint for third party damage

  13. A greenhouse gas monitoring and modelling system for Switzerland: The CarboCount CH project

    Science.gov (United States)

    Brunner, Dominik; Buchmann, Nina; Eugster, Werner; Seneviratne, Sonia; Davin, Edouard; Gruber, Nicolas; Leuenberger, Markus; Bey, Isabelle; Bamberger, Ines; Henne, Stephan; Liu, Yu; Mystakidis, Stefanos; Oney, Brian; Roches, Anne

    2014-05-01

    emission inventories. Atmosphere-biosphere exchange fluxes of CO2 are simulated with the coupled system COSMO-CLM2, i.e. COSMO coupled to the Community Land Model, a state-of-the-art land processes and biogeochemistry model. Here we present a general outline of the project, the setup of the measurement network and of the different modeling components and inverse methods. We have performed transport simulations for the first year of observations and calculated the contributions from anthropogenic and biogenic sources/sinks upstream of the measurement sites. The generally good agreement between simulated and measured concentrations underlines the high quality of the transport simulations, but occasional deviations are pointing towards weaknesses in both the emission inventories and in the simulated meteorology. The CarboCount CH project provides an ideal test bed for future carbon monitoring systems, to test the suitability of different types of monitoring stations, to analyze the challenges of a heterogeneous landscape, and to identify critical modelling components.

  14. Community Air Sensor Network (CAIRSENSE) Project: Lower Cost, Continuous Ambient Monitoring Methods

    Science.gov (United States)

    CAIRSENSE Project presentation was given at the 108th Annual Meeting of the Air & Waste Management Associate in June 2015. The presentation provides an overview of the CAIRSENSE Project and general info about the sensors used in the CAIRSENSE Project.

  15. ["When the ad is good, the product is sold." The MonitorACAO Project and drug advertising in Brazil].

    Science.gov (United States)

    Soares, Jussara Calmon Reis de Souza

    2008-04-01

    This paper presents an analysis on drug advertising in Brazil, based on the final report of the MonitorACAO Project, by the group from the Universidade Federal Fluminense, Niterói, Rio de Janeiro. Due to a partnership between the university and the National Agency for Health Surveillance (ANVISA), drug advertisements were monitored and analyzed for one year, according to the methodology defined by the Agency. The samples were collected in medical practices and hospitals, drugstores, pharmacies and in scientific magazines. TV and radio programs were monitored, in the case of OTC drugs. 159 advertisements referring to pharmaceuticals were sent to ANVISA,from a total of 263 irregular ads analyzed between October 2004 and August 2005. The main problems found were the poor quality of drug information to health professionals, as well as misleading drug use to lay population. Based on the results of this project and on other studies, the banning of drug advertising in Brazil is proposed.

  16. Big Data solution for CTBT monitoring: CEA-IDC joint global cross correlation project

    Science.gov (United States)

    Bobrov, Dmitry; Bell, Randy; Brachet, Nicolas; Gaillard, Pierre; Kitov, Ivan; Rozhkov, Mikhail

    2014-05-01

    Waveform cross-correlation when applied to historical datasets of seismic records provides dramatic improvements in detection, location, and magnitude estimation of natural and manmade seismic events. With correlation techniques, the amplitude threshold of signal detection can be reduced globally by a factor of 2 to 3 relative to currently standard beamforming and STA/LTA detector. The gain in sensitivity corresponds to a body wave magnitude reduction by 0.3 to 0.4 units and doubles the number of events meeting high quality requirements (e.g. detected by three and more seismic stations of the International Monitoring System (IMS). This gain is crucial for seismic monitoring under the Comprehensive Nuclear-Test-Ban Treaty. The International Data Centre (IDC) dataset includes more than 450,000 seismic events, tens of millions of raw detections and continuous seismic data from the primary IMS stations since 2000. This high-quality dataset is a natural candidate for an extensive cross correlation study and the basis of further enhancements in monitoring capabilities. Without this historical dataset recorded by the permanent IMS Seismic Network any improvements would not be feasible. However, due to the mismatch between the volume of data and the performance of the standard Information Technology infrastructure, it becomes impossible to process all the data within tolerable elapsed time. To tackle this problem known as "BigData", the CEA/DASE is part of the French project "DataScale". One objective is to reanalyze 10 years of waveform data from the IMS network with the cross-correlation technique thanks to a dedicated High Performance Computer (HPC) infrastructure operated by the Centre de Calcul Recherche et Technologie (CCRT) at the CEA of Bruyères-le-Châtel. Within 2 years we are planning to enhance detection and phase association algorithms (also using machine learning and automatic classification) and process about 30 terabytes of data provided by the IDC to

  17. Getting Results in Housing: A Framework for Monitoring Results in Housing Projects: Using Measurable Indicators

    OpenAIRE

    Shlomo Angel; Michael Jacobs

    2006-01-01

    The aim of this paper is to help project teams develop results indicators for housing projects. These indicators are intended, primarily, as an instrument for managing projects and should help staff in the country offices, in headquarters and in executing agencies to identify the components of a project that are working as intended, and the ones that may need attention to keep the project on track. Additionally, the indicators can provide a foundation for project evaluations, at the mid-term ...

  18. KM and WEB 2.0 methods for project-based learning. MESHAT : a monitoring and experience sharing tool

    CERN Document Server

    Michel, Christine

    2011-01-01

    Our work aims at studying tools offered to learners and tutors involved in face-to-face or blended project-based learning activities. To understand better the needs and expectations of each actor, we are especially interested in the specific case of project management training. The results of a course observation show that the lack of monitoring and expertise transfer tools involves important dysfunctions in the course organisation and therefore dissatisfaction for tutors and students (in particular about the acquisition of knowledge and expertise). So as to solve this problem, we propose a personalised platform (according to the actor: project group, student or tutor), which gives information to monitor activities and supports the acquisition and transfer of expertise. This platform is based on Knowledge Management (KM) and Web 2.0 concepts to support the dynamic building of knowledge. KM is used to define the learning process (based on the experiential learning theory) and the way the individual knowledge b...

  19. The Urban Environmental Monitoring/100 Cities Project: Legacy of the First Phase and Next Steps

    Science.gov (United States)

    Stefanov, William L.; Wentz, Elizabeth A.; Brazel, Anthony; Netzband, Maik; Moeller, Matthias

    2009-01-01

    The Urban Environmental Monitoring (UEM) project, now known as the 100 Cities Project, at Arizona State University (ASU) is a baseline effort to collect and analyze remotely sensed data for 100 urban centers worldwide. Our overarching goal is to use remote sensing technology to better understand the consequences of rapid urbanization through advanced biophysical measurements, classification methods, and modeling, which can then be used to inform public policy and planning. Urbanization represents one of the most significant alterations that humankind has made to the surface of the earth. In the early 20th century, there were less than 20 cities in the world with populations exceeding 1 million; today, there are more than 400. The consequences of urbanization include the transformation of land surfaces from undisturbed natural environments to land that supports different forms of human activity, including agriculture, residential, commercial, industrial, and infrastructure such as roads and other types of transportation. Each of these land transformations has impacted, to varying degrees, the local climatology, hydrology, geology, and biota that predate human settlement. It is essential that we document, to the best of our ability, the nature of land transformations and the consequences to the existing environment. The focus in the UEM project since its inception has been on rapid urbanization. Rapid urbanization is occurring in hundreds of cities worldwide as population increases and people migrate from rural communities to urban centers in search of employment and a better quality of life. The unintended consequences of rapid urbanization have the potential to cause serious harm to the environment, to human life, and to the resulting built environment because rapid development constrains and rushes decision making. Such rapid decision making can result in poor planning, ineffective policies, and decisions that harm the environment and the quality of human life

  20. Subsurface Characterization and Seismic Monitoring for the Southwest Partnerships Phase III Demonstration Project at Farnsworth Field, TX

    Science.gov (United States)

    Will, R. A.; Balch, R. S.

    2015-12-01

    The Southwest Partnership on Carbon Sequestration is performing seismic based characterization and monitoring activities at an active CO2 EOR project at Farnsworth Field, Texas. CO2 is anthropogenically sourced from a fertilizer and an ethanol plant. The field has 13 CO2 injectors and has sequestered 302,982 metric tonnes of CO2 since October 2013. The field site provides an excellent laboratory for testing a range of monitoring technologies in an operating CO2 flood since planned development is sequential and allows for multiple opportunities to record zero CO2 baseline data, mid-flood data, and fully flooded data. The project is comparing and contrasting several scales of seismic technologies in order to determine best practices for large scale commercial sequestration projects. Characterization efforts include an 85 km2 3D surface seismic survey, baseline and repeat 3D VSP surveys centered on injection wells, cross-well tomography baseline and repeat surveys between injector/producer pairs, and a borehole passive seismic array to monitor induced seismicity. All surveys have contributed to detailed geologic models which were then used for fluid flow and risk assessment simulations. 3D VSP and cross-well data with repeat surveys have allowed for direct comparisons of the reservoir prior to CO2 injection and at eight months into injection, with a goal of imaging the CO2 plume as it moves away from injection wells. Additional repeat surveys at regular intervals will continue to refine the plume. The goal of this work is to demonstrate seismic based technologies to monitor CO2 sequestration projects, and to contribute to best practices manuals for commercial scale CO2 sequestration projects. In this talk the seismic plan will be outlined, progress towards goals enumerated, and preliminary results from baseline and repeat seismic data will be discussed. Funding for this project is provided by the U.S. Department of Energy under Award No. DE-FC26-05NT42591.

  1. Fire fighters and rescuers monitoring through wearable sensors: The ProeTEX project.

    Science.gov (United States)

    Magenes, Giovanni; Curone, Davide; Caldani, Laura; Secco, Emanuele Lindo

    2010-01-01

    The final generation of ProeTEX prototypes has been delivered in April 2010: it is based on two sets of sensorized garments devoted to monitor the health status of emergency operators working in harsh environments. This new release of garments shows several improvements with respect to the previous ones, and it is characterized by a major specialization to the requirements imposed by the different categories of end-users (Fire-Fighters, Civil Protection rescuers) addressed by the project. Each ProeTEX prototype is provided with a communication infrastructure allowing the real-time remote transmission of data recorded by the wearable sensors, and the presentation of such data to possible managers supervising the activities of the first line responders. After the delivery of the prototypes, an intense validation of the garments is being carried out both in laboratories, specialized in physiological measures, and in simulated fire-fighting scenarios. In such a context, this paper presents the main features characterizing the final ProeTEX prototypes and preliminary results of their laboratory assessment.

  2. The Lick AGN Monitoring Project: Recalibrating Single-Epoch Virial Black Hole Mass Estimates

    CERN Document Server

    Park, Daeseong; Treu, Tommaso; Barth, Aaron J; Bentz, Misty C; Bennert, Vardha N; Canalizo, Gabriela; Filippenko, Alexei V; Gates, Elinor; Greene, Jenny E; Malkan, Matthew A; Walsh, Jonelle

    2011-01-01

    We investigate the calibration and uncertainties of black hole mass estimates based on the single-epoch (SE) method, using homogeneous and high-quality multi-epoch spectra obtained by the Lick Active Galactic Nucleus (AGN) Monitoring Project for 9 local Seyfert 1 galaxies with black hole masses < 10^8 M_sun. By decomposing the spectra into their AGN and stellar components, we study the variability of the single-epoch Hbeta line width (full width at half-maximum intensity, FWHM_Hbeta; or dispersion, sigma_Hbeta) and of the AGN continuum luminosity at 5100A (L_5100). From the distribution of the "virial products" (~ FWHM_Hbeta^2 L_5100^0.5 or sigma_Hbeta^2 L_5100^0.5) measured from SE spectra, we estimate the uncertainty due to the combined variability as ~ 0.05 dex (12%). This is subdominant with respect to the total uncertainty in SE mass estimates, which is dominated by uncertainties in the size-luminosity relation and virial coefficient, and is estimated to be ~ 0.46 dex (factor of ~ 3). By comparing the...

  3. FINAL TECHNICAL REPORT: Underwater Active Acoustic Monitoring Network For Marine And Hydrokinetic Energy Projects

    Energy Technology Data Exchange (ETDEWEB)

    Stein, Peter J. [Scientific Solutions, Inc, Nashua, NH (United States); Edson, Patrick L. [Scientific Solutions, Inc, Nashua, NH (United States)

    2013-12-20

    This project saw the completion of the design and development of a second generation, high frequency (90-120 kHz) Subsurface-Threat Detection Sonar Network (SDSN). The system was deployed, operated, and tested in Cobscook Bay, Maine near the site the Ocean Renewable Power Company TidGen™ power unit. This effort resulted in a very successful demonstration of the SDSN detection, tracking, localization, and classification capabilities in a high current, MHK environment as measured by results from the detection and tracking trials in Cobscook Bay. The new high frequency node, designed to operate outside the hearing range of a subset of marine mammals, was shown to detect and track objects of marine mammal-like target strength to ranges of approximately 500 meters. This performance range results in the SDSN system tracking objects for a significant duration - on the order of minutes - even in a tidal flow of 5-7 knots, potentially allowing time for MHK system or operator decision-making if marine mammals are present. Having demonstrated detection and tracking of synthetic targets with target strengths similar to some marine mammals, the primary hurdle to eventual automated monitoring is a dataset of actual marine mammal kinematic behavior and modifying the tracking algorithms and parameters which are currently tuned to human diver kinematics and classification.

  4. Suncatcher Monitoring Project. Final report, September 1, 1977-December 31, 1978

    Energy Technology Data Exchange (ETDEWEB)

    Maeda, B.T.; Grant, P.W.; Anson, R.D.

    1979-08-01

    The Suncatcher Monitoring Project has to date accumulated a wide variety of data on the Nittler/Maeda Suncatcher house in Davis, California, designed by Living Systems. Highlights of the data indicate 70% solar heating during 1978 despite unusually adverse winter weather conditons and a 40% increase of solar energy in winter through clerestory glazing as compared to ordinary south glazing. The data acquisition system (DAS) only worked intermittently during 1978, but hourly data was gathered during several intervals and daily data was virtually continuous. As a back-up to this hourly gathering of data hand read data was taken daily from September 1977 to the present. This manually collected data has allowed a reliable estimate of the Suncatcher house's performance. Summer data on Suncatcher window performance has been collected for comparison purposes, but budget constraints have delayed completion of computer modeling of the Suncatcher performance. Comparison of the overall Suncatcher's performance with the estimation models, SOLEST and LASL6, and simulation model, SOLSIM, appear accurate, although completion of the reflector enhancement algorithm remains desirable.

  5. Earth Observation in Support of Sustainable Urban Planning: Results of the Dragon-3 Monitor Project

    Science.gov (United States)

    Cartalis, C.; Polydoros, A.; Mavrakou, T.; Asimakopoulos, D. N.

    2016-08-01

    Sustainable urban planning increasingly demands innovative concepts and techniques to obtain up-to-date and area-wide information on the characteristics and development of the urban system. In this paper, a thorough and conclusive presentation is made in terms of the results of the DRAGON-3 MONITOR project as based on the use of Earth Observation. Results refer in particular to a set of EO based dynamic urban indicators (i.e. urban form and expansion, land use/land cover changes, land surface temperature distribution, the presence and strength of urban heat island) with the capacity to describe the state, dynamic changes and interaction of the land and thermal environment in urban areas. Furthermore results are assessed in terms of their potential to operationally support sustainable urban planning and bridge the gap between EO scientists and urban planners. Constraints related to the spatial resolution and revisit time of satellite sensors are discussed as they influence the accuracy and applicability of the indicators. Methodologies to improve the applicability of the indicators are also discussed along with the presentation of the respective results.

  6. The Monitor project: the search for transits in the open cluster NGC 2362

    Science.gov (United States)

    Miller, Adam A.; Irwin, Jonathan; Aigrain, Suzanne; Hodgkin, Simon; Hebb, Leslie

    2008-06-01

    We present the results of a systematic search for transiting planets in a ~5 Myr open cluster, NGC 2362. We observed ~1200 candidate cluster members, of which ~475 are believed to be genuine cluster members, for a total of ~100 h. We identify 15 light curves with reductions in flux that pass all our detection criteria, and six of the candidates have occultation depths compatible with a planetary companion. The variability in these six light curves would require very large planets to reproduce the observed transit depth. If we assume that none of our candidates are, in fact, planets then we can place upper limits on the fraction of stars with hot Jupiters (HJs) in NGC 2362. We obtain 99 per cent confidence upper limits of 0.22 and 0.70 on the fraction of stars with HJs (fp) for 1-3 and 3-10 d orbits, respectively, assuming all HJs have a planetary radius of 1.5RJup. These upper limits represent observational constraints on the number of stars with HJs at an age <~10 Myr, when the vast majority of stars are thought to have lost their protoplanetary discs. Finally, we extend our results to the entire Monitor project, a survey searching young, open clusters for planetary transits, and find that the survey as currently designed should be capable of placing upper limits on fp near the observed values of fp in the solar neighbourhood.

  7. The Lick AGN Monitoring Project 2011: Reverberation Mapping of Markarian 50

    CERN Document Server

    Barth, A J; Thorman, S J; Bennert, V N; Sand, D J; Li, W; Canalizo, G; Filippenko, A V; Gates, E L; Greene, J E; Malkan, M A; Stern, D; Treu, T; Woo, J -H; Assef, R J; Bae, H -J; Brewer, B J; Buehler, T; Cenko, S B; Clubb, K I; Cooper, M C; Diamond-Stanic, A M; Hiner, K D; Hoenig, S F; Joner, M D; Kandrashoff, M T; Laney, C D; Lazarova, M S; Nierenberg, A M; Park, D; Silverman, J M; Son, D; Sonnenfeld, A; Tollerud, E J; Walsh, J L; Walters, R; da Silva, R L; Fumagalli, M; Gregg, M D; Harris, C E; Hsiao, E Y; Lee, J; Lopez, L; Rex, J; Suzuki, N; Trump, J R; Tytler, D; Worseck, G; Yesuf, H M

    2011-01-01

    The Lick AGN Monitoring Project 2011 observing campaign was carried out over the course of 11 weeks in Spring 2011. Here we present the first results from this program, a measurement of the broad-line reverberation lag in the Seyfert 1 galaxy Mrk 50. Combining our data with supplemental observations obtained prior to the start of the main observing campaign, our dataset covers a total duration of 4.5 months. During this time, Mrk 50 was highly variable, exhibiting a maximum variability amplitude of a factor of 4 in the U-band continuum and a factor of 2 in the H-beta line. Using standard cross-correlation techniques, we find that H-beta and H-gamma lag the V-band continuum by tau_cen = 10.64(-0.93,+0.82) and 8.43(-1.28,+1.30) days, respectively, while the lag of He II 4686 is unresolved. The H-beta line exhibits a symmetric velocity-resolved reverberation signature with shorter lags in the high-velocity wings than in the line core, consistent with an origin in a broad-line region dominated by orbital motion r...

  8. Modeling reverberation mapping data II: dynamical modeling of the Lick AGN Monitoring Project 2008 dataset

    CERN Document Server

    Pancoast, Anna; Treu, Tommaso; Park, Daeseong; Barth, Aaron J; Bentz, Misty C; Woo, Jong-Hak

    2013-01-01

    We present dynamical modeling of the broad line region (BLR) for a sample of five Seyfert 1 galaxies using reverberation mapping data taken by the Lick AGN Monitoring Project (LAMP) in 2008. The sample includes Arp 151, Mrk 1310, NGC 5548, NGC 6814, and SBS 1116+583A. By modeling the continuum light curve and H$\\beta$ line profiles directly we are able to constrain the geometry and kinematics of the BLR. Modeling the kinematics also allows us to make a measurement of the black hole mass that does not depend upon the virial coefficient or normalizing factor needed in traditional reverberation mapping analysis. We find that the geometry of the BLR is generally a thick disk viewed close to face-on, but a more spherical geometry is not ruled out for two of the five AGNs. While the H$\\beta$ is found to come preferentially from the far side of the BLR, the mean size of the BLR is consistent with the lags measured with cross-correlation analysis. The BLR kinematics are generally found to be consistent with either in...

  9. Modelling reverberation mapping data - II. Dynamical modelling of the Lick AGN Monitoring Project 2008 data set

    Science.gov (United States)

    Pancoast, Anna; Brewer, Brendon J.; Treu, Tommaso; Park, Daeseong; Barth, Aaron J.; Bentz, Misty C.; Woo, Jong-Hak

    2014-12-01

    We present dynamical modelling of the broad-line region (BLR) for a sample of five Seyfert 1 galaxies using reverberation mapping data taken by the Lick AGN Monitoring Project in 2008. By modelling the AGN continuum light curve and Hβ line profiles directly, we are able to constrain the geometry and kinematics of the BLR and make a measurement of the black hole mass that does not depend upon the virial factor, f, needed in traditional reverberation mapping analysis. We find that the geometry of the BLR is generally a thick disc viewed close to face-on. While the Hβ emission is found to come preferentially from the far side of the BLR, the mean size of the BLR is consistent with the lags measured with cross-correlation analysis. The BLR kinematics are found to be consistent with either inflowing motions or elliptical orbits, often with some combination of the two. We measure black hole masses of log _{10}(M_ BH/M_{odot })=6.62^{+0.10}_{-0.13} for Arp 151, 7.42^{+0.26}_{-0.27} for Mrk 1310, 7.59^{+0.24}_{-0.21} for NGC 5548, 6.37^{+0.21}_{-0.16} for NGC 6814, and 6.99^{+0.32}_{-0.25} for SBS 1116+583A. The f factors measured individually for each AGN are found to correlate with inclination angle, although not with M BH, L5100, or FWHM/σ of the emission line profile.

  10. TANK 241-AN-102 MULTI-PROBE CORROSION MONITORING SYSTEM PROJECT LESSONS LEARNED

    Energy Technology Data Exchange (ETDEWEB)

    TAYLOR T; HAGENSEN A; KIRCH NW

    2008-07-07

    During 2007 and 2008, a new Multi-Probe Corrosion Monitoring System (MPCMS) was designed and fabricated for use in double-shell tank 241-AN-102. The system was successfully installed in the tank on May 1, 2008. The 241-AN-102 MPCMS consists of one 'fixed' in-tank probe containing primary and secondary reference electrodes, tank material electrodes, Electrical Resistance (ER) sensors, and stressed and unstressed corrosion coupons. In addition to the fixed probe, the 241-AN-102 MPCMS also contains four standalone coupon racks, or 'removable' probes. Each rack contains stressed and unstressed coupons made of American Society of Testing and Materials A537 CL1 steel, heat-treated to closely match the chemical and mechanical characteristics of the 241-AN-102 tank wall. These coupon racks can be removed periodically to facilitate examination of the attached coupons for corrosion damage. Along the way to successful system deployment and operation, the system design, fabrication, and testing activities presented a number of challenges. This document discusses these challenges and lessons learned, which when applied to future efforts, should improve overall project efficiency.

  11. Yakima/Klickitat Fisheries Project Genetic Studies; Yakima/Klickitat Fisheries Project Monitoring and Evaluation, 2000-2001 Annual Report.

    Energy Technology Data Exchange (ETDEWEB)

    Busack, Craig A.; Schroder, Steven L.; Young, Sewall F. (Washington Department of Fish and Wildlife, Olympia, WA)

    2002-11-01

    Genetic work for 2001 consisted of two major phases, both reported on here. The first is a DNA microsatellite analysis of several hundred juveniles from the experimental spawning channel at the Cle Elum Supplementation Research Facility, using the genetic markers to assign the juveniles to parents, and thus judge reproductive success of individual fish. The second is a reevaluation and revision of plans for studying domestication in the spring chinook supplementation effort. The pedigree analysis was significant in three respects. First, it showed that this approach can be successfully applied to the spawning channel research. Secondly it showed that this approach does indeed yield very useful information about the relative reproductive success of fish in the channel. Finally, it showed that this information can yield additional information about the experimental design. Of the 961 juveniles on which analysis was attempted, 774 yielded enough genetic information to be used in the pedigree analysis. Of these, 754 were assigned to males and females known to have been placed into the channel. Of the other 20, all were assignable to females, but sires were unknown. The genotypes of 17 of these were consistent with a single theoretical male genotype, suggesting a single precocial male sired them. The inferred parentage of the fish demonstrated that there had been substantial leakage of juveniles from one section of the channel into another. Reproductive success of females was fairly even, but success of males varied considerably. In a group of seven males (including the hypothetical one), one contributed 79% of the progeny analyzed, and three contributed none. The domestication experimental design evaluation was prompted by a critical review of the project by the Independent Scientific Review Panel (ISRP). The ISRP review set into motion a design revision process which extended beyond the contract period; the report presented here is intended to be an account of our

  12. Geohazard monitoring and modelling using Persistent Scatterer Interferometry in the framework of the European project Terrafirma

    Science.gov (United States)

    Cooksley, Geraint; Arnaud, Alain; Banwell, Marie-Josée

    2013-04-01

    Increasingly, geohazard risk managers are looking to satellite observations as a promising option for supporting their risk management and mitigation strategies. The Terrafirma project, aimed at supporting civil protection agencies, local authorities in charge of risk assessment and mitigation is a pan-European ground motion information service funded by the European Space Agency's Global Monitoring for Environment and Security initiative. Over 100 services were delivered to organizations over the last ten years. Terrafirma promotes the use of Synthetic Aperture Radar Interferometry (InSAR) and Persistent Scatterer InSAR (PSI) within three thematic areas for terrain motion analysis: Tectonics, Flooding and Hydrogeology (ground water, landslides and inactive mines), as well as the innovative Wide Area mapping service, aimed at measuring land deformation over very large areas. Terrafirma's thematic services are based on advanced satellite interferometry products; however they exploit additional data sources, including non-EO, coupled with expert interpretation specific to each thematic line. Based on the combination of satellite-derived ground-motion information products with expert motion interpretation, a portfolio of services addressing geo-hazard land motion issues was made available to users. Although not a thematic in itself, the Wide Area mapping product constitutes the fourth quarter of the Terrafirma activities. The wide area processing chain is nearly fully automatic and requires only a little operator interaction. The service offers an operational PSI processing for wide-area mapping with mm accuracy of ground-deformation measurement at a scale of 1:250,000 (i.e. one cm in the map corresponds to 2.5 Km on the ground) on a country or continent level. The WAP was demonstrated using stripmap ERS data however it is foreseen to be a standard for the upcoming Sentinel-1 mission that will be operated in Terrain Observation by Progressive Scan (TOPS) mode. Within

  13. The Navruz Project: Transboundary Monitoring for Radionuclides and Metals in Central Asia Rivers. Sampling and Analysis Plan and Operational Manual

    Energy Technology Data Exchange (ETDEWEB)

    Passell, Howard D.; Barber, David S.; Betsill, J. David; Littlfield, Adriane C.; Mohagheghi, Amir H.; Shanks, Sonoya T.; Yuldashev, Bekhzad; Salikhbaev, Umar; Radyuk, Raisa; Djuraev, Akram; Djuraev, Amwar; Vasilev, Ivan; Tolongutov, Bajgabyl; Valentina, Alekhina; Solodukhin, Vladimir; Pozniak, Victor

    2002-04-02

    The transboundary nature of water resources demands a transboundary approach to their monitoring and management. However, transboundary water projects raise a challenging set of problems related to communication issues, and standardization of sampling, analysis and data management methods. This manual addresses those challenges and provides the information and guidance needed to perform the Navruz Project, a cooperative, transboundary, river monitoring project involving rivers and institutions in Kazakhstan, Kyrgyzstan, Tajikistan, and Uzbekistan facilitated by Sandia National Laboratories in the U.S. The Navruz Project focuses on waterborne radionuclides and metals because of their importance to public health and nuclear materials proliferation concerns in the region. This manual provides guidelines for participants on sample and data collection, field equipment operations and procedures, sample handling, laboratory analysis, and data management. Also included are descriptions of rivers, sampling sites and parameters on which data are collected. Data obtained in this project are shared among all participating countries and the public through an internet web site, and are available for use in further studies and in regional transboundary water resource management efforts. Overall, the project addresses three main goals: to help increase capabilities in Central Asian nations for sustainable water resources management; to provide a scientific basis for supporting nuclear transparency and non-proliferation in the region; and to help reduce the threat of conflict in Central Asia over water resources, proliferation concerns, or other factors.

  14. Emergency Management and Radiation Moni-toring in Nuclear and Radiological Accidents. Summary Report on the NKS Project EMARAD

    Energy Technology Data Exchange (ETDEWEB)

    Lahtinen, J. [Radiation and Nuclear Safety Authority (STUK) (Finland)

    2006-04-15

    In order to manage various nuclear or radiological emergencies the authorities must have pre-prepared plans. The purpose of the NKS project EMARAD (Emergency Management and Radiation Monitoring in Nuclear and Radiological Accidents) was to produce and gather various data and information that could be useful in drawing up emergency plans and radiation monitoring strategies. One of the specific objectives of the project was to establish a www site that would contain various radiation-threat and radiation-monitoring related data and documents and that could be accessed by all Nordic countries. Other important objectives were discussing various factors affecting measurements in an emergency, efficient use of communication technology and disseminating relevant information on such topics as urban dispersion and illicit use of radiation. The web server is hosted by the Radiation and Nuclear Safety Authority (STUK) of Finland. The data stored include pre-calculated consequence data for nuclear power plant accidents as well as documents and presentations describing e.g. general features of monitoring strategies, the testing of the British urban dispersion model UDM and the scenarios and aspects related to malicious use of radiation sources and radioactive material. As regards the last item mentioned, a special workshop dealing with the subject was arranged in Sweden in 2005 within the framework of the project. (au)

  15. Assessment of Diversity, Distribution, Conservation Status and Preparation of Management Plan for Medicinal Plants in the Catchment Area of Parbati Hydroelectric Project Stage -Ⅲ in Northwestern Himalaya

    Institute of Scientific and Technical Information of China (English)

    S.S. Samant; Jitendra S. Butola; Aman Sharma

    2007-01-01

    The developmental activities, particularly the construction of hydroelectric projects are causing a great loss of biodiversity in the Indian Himalayan Region. The Himachal Pradesh, a part of IHR is well known for the development of hydroelectric projects.The Parbati H.E. Project is amongst the major projects of the State. The different stages of the project are all causing loss of biodiversity of the area.Stage Ⅲ of the Parbati H.E. Project is a run of the river scheme on the Sainj River downstream of Power House of Parbati H.E. Project Stage Ⅱ. The project shall utilize regulated discharge of Parbati H.E.Project Stage Ⅱ and inflow of River Sainj for power generation, and has been contemplated as a peaking station operating in tandem with Stage Ⅱ. The present study has been undertaken to see the impact of hydroelectric project on the biodiversity, particularly on medicinal plants. A total of 104 species of medicinal plants, belonging to different life forms, i.e.,trees (23 spp.), shrubs (22 spp.), herbs (57 spp.) and ferns (2 spp.) were recorded. The species have been analyzed and studied for their distribution,classification, altitudinal zones, part (s) used,indigenous uses, nativity, endemism and rarity.Different parts of these species, such as whole plants,roots (including rhizomes and tubers), leaves, flowers,fruits, seeds, stems, barks, spikes, nuts and insect galls are used by the inhabitants for curing various diseases and ailments. 30 species are native to the Himalayan region, 9 species native to the Himalayan region and adjacent countries also and 65 species are non-natives. 9 species are near endemics. Considering the whole Himalaya as a biogeographic unit (sensu lato),the near endemics are endemic to the Himalaya.Among these species, Zanthoxylum armatum is categorized as Endangered and Valeriana wallichii as Vulnerable. Hedychium spicatum, Rhus javanica,Berberis lycium, Thalictrum foliolossum, Salvia lanata, Rubia cordifolia and Bergenia

  16. Earth Observation in aid of surge monitoring and forecasting: ESA's eSurge Project

    Science.gov (United States)

    Harwood, Phillip; Cipollini, Paolo; Snaith, Helen; Høyer, Jacob; Dwyer, Ned; Dunne, Declan; Stoffelen, Ad; Donlon, Craig

    2013-04-01

    The understanding and realistic modelling of surges supports both preparation and mitigation activities and should eventually bring enormous societal benefits, especially to some of the world's poorest countries. Earth Observation data from satellites have an important role to play in storm surge monitoring and forecasting, but the full uptake of these data by the users (such as environmental agencies and tidal prediction centres) must be first encouraged by showcasing their usefulness, and then supported by providing easy access. The European Space Agency has recognized the above needs and, through its Data User Element (DUE) programme, has initiated in 2011 the eSurge project, whose aims are: a) to contribute through Earth Observation to an integrated approach to storm surge, wave, sea-level and flood forecasting as part of a wider optimal strategy for building an improved forecast and warning capability for coastal inundation; and b) to increase the use of the advanced capabilities of ESA and other satellite data for storm surge applications. The project is led by Logica UK, with NOC (UK), DMI (Denmark), CMRC (Ireland) and KNMI (Netherlands) as scientific partners. eSurge aims to provide easy access to a wide range of relevant data for a range of historical surge events, as well as performing a series of experiments to demonstrate the value of this data, and running workshops and training courses to help users make use of the available data. The eSurge database of Earth Observation and in situ measurements for past surge events is now publicly available. In 2013 the project moves into its service demonstration phase, adding more data and events, including a demonstration near real time service. The project works closely with its users in order to meet their needs and to maximise the return of this data. A novel dataset provided by eSurge is coastal altimetry. Coastal altimetry has a prominent role to play as it measures directly the total water level envelope

  17. Aircraft Engine Life-Consumption Monitoring for Real-Time Reliability Determination Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A real-time life-use consumption monitor is proposed for aircraft engine systems. The life monitor will process power data available on the aircraft to calculate the...

  18. Autonomus I&C Maintenance and Health Monitoring System for Fission Surface Power Project

    Data.gov (United States)

    National Aeronautics and Space Administration — There currently exists no end-to-end reactor/power conversion monitoring system that can provide both autonomous health monitoring, but also in-situ sensor...

  19. Final Restoration and Mitigation Monitoring Plan for the Island Ponds Restoration Project

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This Restoration and Mitigation Monitoring Plan (RMMP) presents the approaches necessary to satisfy mitigation and monitoring requirements described in the various...

  20. Advanced Rapid Imaging & Analysis for Monitoring Hazards (ARIA-MH) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Develop a service-oriented hazard/disaster monitoring data system enabling both science and decision-support communities to monitor ground motion in areas of...

  1. CATSIUS CLAY PROJECT: Calculation and testing of behaviour of unsaturated clay as barrier in radioactive waste repositories: stage 3: validation exercises at a large in situ scale

    Energy Technology Data Exchange (ETDEWEB)

    Alonso, E. E.; Alcoverro, J.

    1999-07-01

    Stage 3 of CATSIUS CLAY Project: Validation Exercises at a Large in situ Scale includes two Benchmarks: Benchmark 3.1: In situ Hydration of Boom Clay Pellets (BACCHUS 2) and Benchmark 3.2: FEBEX Mock-up Test. The BACCHUS 2 in situ test was performed in the HADES underground laboratory (Mol, Belgium) to demonstrate and optimize an installation procedure for a clay based material and to study its hydration process. After drilling a vertical shaft (540 mm in diameter, 3.0 m in length) in the host Boom clay, a central filter (90 mm in diameter) was placed, the remaining space was filled with a mixture of clay pellets and clay powder and the assembly was sealed at the upper end by a resin plug (0.20 m in thickness) over which concrete was poured. The test was instrumented so that it could be used as a validation experiment. Total stress, pore water pressure and water content measurements were performed both in the backfill material and in the surrounding clay massif. Once the installation was complete, the natural hydration of the backfill material began (day 0). To accelerate the hydration process, on day 516 water was injected through the central filter. On day 624, after the saturation of the backfill was reached, the hydraulic circuit was closed and the undrained response of the system backfill-host clay was monitored until an overall steady state was reached. Partners were asked to provide predictions for the evolution of the pore water pressure and total pressure of various points where appropriate sensors are installed. This benchmark addresses the Hydro-Mechanical response of an unsaturated low density clay barrier under natural and artificial hydration. (Author)

  2. Analysis of HSE cost in construction stage of petrochemical project%石化项目施工阶段HSE费用探析

    Institute of Scientific and Technical Information of China (English)

    陈瑜芳

    2011-01-01

    施工阶段HSE费用的确定是项目建设过程中的重要一环.在简述石化项目建设施工阶段HSE费用计取的依据及其范围的基础上,总结了石化项目施工阶段HSE费用的项目组成,说明了其计算方法和注意事项.%The determination of HSE costs in construction stage is important in the process of project construction. On the basis of HSE cost and its range in the construction stage, the composition of HSE costs in project construction stage is summarized, and calculation methods and precautions are described.

  3. Soil Contamination, Advanced integrated characterisation and time-lapse Monitoring, SoilCAM project highlights

    Science.gov (United States)

    French, H. K.; Van Der Zee, S. E.; Wehrer, M.; Godio, A.; Pedersen, L. B.; Tsocano, G.

    2013-12-01

    The SoilCAM project (2008- 2012, EU-FP7-212663) aimed at improving methods for monitoring subsurace contaminant distribution and biodegradation. Two test sites were chosen, Oslo airport Gardermoen, Norway where de-icing agents infiltrate the soil during snowmelt and the Trecate site in Italy where an inland crude oil spill occurred in 1994. A number of geophysical investigation techniques were combined with soil and water sampling techniques. Data obtained from time-lapse measurements were further analysed by numerical modelling of flow and transport at different scales in order to characterise transport processes in the unsaturated and saturated zones. Laboratory experiments provided physical and biogeochemical data for model parameterisation and to select remediation methods. The geophysical techniques were used to map geological heterogeneities and to conduct time-lapse measurements of processes in the unsaturated zone. Both cross borehole and surface electrodes were used for electrical resistivity and induced polarisation surveys. Results showed clear indications of areas highly affected by de-icing chemicals along the runway at Oslo airport. The time lapse measurements along the runway at the airport showed infiltration patterns during snowmelt and were used to validate 2D unsaturated flow and transport simulations using SUTRA. The simulations illustrate the effect of layering geological structures and membranes, buried parallel to the runway, on the flow pattern. Complex interaction between bio-geo-chemical processes in a 1D vertical profile along the runway were described with the ORCHESTRA model. Smaller scale field site measurements revealed increase of iron and manganese during degradation of de-icing chemicals. At the Trecate site a combination of georadar, electrical resistivity and radio magneto telluric provided a broad outline of the geology down to 50 m. Anomalies in the Induced polarisation and electrical resistivity data from the cross borehole

  4. Decomposition of Near-Infrared Spectroscopy Signals Using Oblique Subspace Projections: Applications in Brain Hemodynamic Monitoring

    Science.gov (United States)

    Caicedo, Alexander; Varon, Carolina; Hunyadi, Borbala; Papademetriou, Maria; Tachtsidis, Ilias; Van Huffel, Sabine

    2016-01-01

    Clinical data is comprised by a large number of synchronously collected biomedical signals that are measured at different locations. Deciphering the interrelationships of these signals can yield important information about their dependence providing some useful clinical diagnostic data. For instance, by computing the coupling between Near-Infrared Spectroscopy signals (NIRS) and systemic variables the status of the hemodynamic regulation mechanisms can be assessed. In this paper we introduce an algorithm for the decomposition of NIRS signals into additive components. The algorithm, SIgnal DEcomposition base on Obliques Subspace Projections (SIDE-ObSP), assumes that the measured NIRS signal is a linear combination of the systemic measurements, following the linear regression model y = Ax + ϵ. SIDE-ObSP decomposes the output such that, each component in the decomposition represents the sole linear influence of one corresponding regressor variable. This decomposition scheme aims at providing a better understanding of the relation between NIRS and systemic variables, and to provide a framework for the clinical interpretation of regression algorithms, thereby, facilitating their introduction into clinical practice. SIDE-ObSP combines oblique subspace projections (ObSP) with the structure of a mean average system in order to define adequate signal subspaces. To guarantee smoothness in the estimated regression parameters, as observed in normal physiological processes, we impose a Tikhonov regularization using a matrix differential operator. We evaluate the performance of SIDE-ObSP by using a synthetic dataset, and present two case studies in the field of cerebral hemodynamics monitoring using NIRS. In addition, we compare the performance of this method with other system identification techniques. In the first case study data from 20 neonates during the first 3 days of life was used, here SIDE-ObSP decoupled the influence of changes in arterial oxygen saturation from the

  5. A multi-year monitoring project of the high-altitude Cenote ice cave, Dolomites, Italy

    Science.gov (United States)

    Sauro, Francesco; Santagata, Tommaso; Spötl, Christoph; Festi, Daniela; Oeggl, Klaus; Dal Molin, Luca; De Waele, Jo

    2016-04-01

    The Cenote ice cave hosts one of the most voluminous cave glaciers of the Dolomites. This 280 m-deep abyss was discovered in 1994 after the entrance had opened as a result of the abrupt emptying of a small lake at 2940 m a.s.l. in the Regional Park of Fanes, Sennes and Braies. The cave consists of a massive, 130 m-thick layered ice deposit carved by meltwater tunnels and chimneys excavated from below by ascending air. At the lower limit of the cave glacier a shaft opens - ice-free and 165 m deep - leading into a dome occupied by a cave rock glacier with typical terminal tongue embankments. A research project was launched to monitor long-term movements and volume changes of this ice deposit as well as to understand the cave microclimate and the potential for future palaeoclimate studies. During October 2015 a first expedition performed a complete survey of the final chamber using a Leica HDS7000, a phase difference laser scanner equipped with a dual axis compensator, on-board control, a wavelenght of 1.5 microns, a laser "CLASS 1" with a flow rate of 187 m and a resolution of 0.1 mm. A scan station was performed also at 110 m above the bottom of the shaft to map in detail the lower side of the hanging ice glacier. This survey has provided the detailed volume of the chamber (420,000 m3) as well as a first record of the position of the ice masses hanging on the ceiling and of the rock glacier at the bottom. Barometric, temperature and humidity dataloggers have been installed in the cave to record the microclimate. In addition pollen traps have been installed to study the present flux of pollen at the surface and inside the cave, while preliminary analyses on pollen grains preserved in the ice are being carried out. The Cenote ice cave research project aims to shed light on the climate evolution of the Dolomites during the last hundreds or possibly thousands of years, as well as on the more recent environmental changes that lead to the upward melting of the cave

  6. Using the Citizen Science Picture Post Project as the Foundation for Campus Environmental Monitoring by Undergraduate Student Researchers

    Science.gov (United States)

    Bowen, K.; Guertin, L. A.

    2014-12-01

    Penn State Brandywine is utilizing the citizen science Picture Post network as a foundation for collecting campus environmental data and for undergraduate student research investigations. The Picture Post is an environmental monitoring project a part of Digital Earth Watch, a citizen science initiative funded by NASA. Picture Post creates opportunities for educators and community members to take digital photos from octagonal platforms on posts registered as part of the Picture Post national network and then share these photos online. Penn State Brandywine joined the Picture Post project May 27, 2014, to begin a long-term monitoring program, starting with an environmental baseline of the campus landscape. Four post locations were selected on campus based upon projected major construction projects. Photos at each post are being taken by students on a weekly basis and uploaded to the Picture Post website. The campus community and beyond are also being encouraged to take their own photos to upload to the website. Instructional signage has been placed on each post, and a Penn State Brandywine Picture Post website (http://sites.psu.edu/picturepost/) has been created to explain the project and campus objectives in more detail. This project was started by a student as part of her undergraduate summer research experience and will continue to be managed by students in future semesters. With just a half-year of Picture Post photos, it is evident that there are documented changes in the environment because of construction and expected seasonal variations. The Picture Post photos have provided enough data for an initial undergraduate research project with a student analyzing and comparing the variations in the greenness factor of the photos with supplemental temperature and precipitation data. This project will continue to provide opportunities for citizen contributions to the network as well as data for student investigations of the changing campus environment.

  7. alpha1-acid glycoprotein as a putative biomarker for monitoring the development of the type II reactional stage of leprosy.

    Science.gov (United States)

    Gupta, Nishma; Shankernarayan, Nallakandy P; Dharmalingam, Kuppamuthu

    2010-04-01

    Leprosy, a spectral disease manifested on the basis of host immune responses, is complicated by its reactional stages, namely type I reversal reaction (RR) and type II erythema nodosum leprosum (ENL). These reactional stages are characterized by uncontrolled and aberrant immune responses. Biomarkers for reactional stages would aid in early diagnosis, efficient treatment, prevention of neurological complications and prediction of predisposition to reactional stages. In this study, comparative analysis of the serum proteome of leprosy patients by two-dimensional electrophoresis (2DE) followed by mass spectrometry showed differential expression of acute-phase protein alpha (1)-acid glycoprotein (AGP; also known as orosomucoid). AGP levels in untreated ENL cases were significantly higher than in lepromatous leprosy (LL; a non-reactional disease stage) (P=0.0126), RR (P=0.0176) and healthy controls (P=0.0030). These data were confirmed using ELISA. The levels of AGP decreased to normal levels after treatment with multidrug therapy and thalidomide (P =0.0167). In a follow-up study, AGP levels, which were high in the untreated ENL stage, decreased significantly at 5 days ( P=0.0084) and 21 days (P=0.0027) post-treatment. A stage-dependent increase in AGP in an LL patient who progressed into the ENL stage was also shown. Glycosylation analysis by 2DE showed differential expression of acidic glycoforms of AGP in untreated ENL cases. Changes in AGP concentration and differential expression of isoforms correlated with the inflammatory condition in ENL and also with the treatment regimen. Thus, initial validation of AGP as an ENL-specific biomarker and treatment indicator was shown in this study.

  8. Stored CO2 and Methane Leakage Risk Assessment and Monitoring Tool Development: CO2 Capture Project Phase 2 (CCP2)

    Energy Technology Data Exchange (ETDEWEB)

    Dan Kieki

    2008-09-30

    The primary project goal is to develop and test tools for optimization of ECBM recovery and geologic storage of CO{sub 2} in coalbeds, in addition to tools for monitoring CO{sub 2} sequestration in coalbeds to support risk assessment. Three critical topics identified are (1) the integrity of coal bed methane geologic and engineered systems, (2) the optimization of the coal bed storage process, and (3) reliable monitoring and verification systems appropriate to the special conditions of CO{sub 2} storage and flow in coals.

  9. NOx Emissions Characteristics and Correlation Equations of Two P and W's Axially Staged Sector Combustors Developed Under NASA Environmentally Responsible Aviation (ERA) Project

    Science.gov (United States)

    He, Zhuohui J.

    2017-01-01

    Two P&W (Pratt & Whitney)'s axially staged sector combustors have been developed under NASA's Environmentally Responsible Aviation (ERA) project. One combustor was developed under ERA Phase I, and the other was developed under ERA Phase II. Nitrogen oxides (NOx) emissions characteristics and correlation equations for these two sector combustors are reported in this article. The Phase I design was to optimize the NOx emissions reduction potential, while the Phase II design was more practical and robust. Multiple injection points and fuel staging strategies are used in the combustor design. Pilot-stage injectors are located on the front dome plate of the combustor, and main-stage injectors are positioned on the top and bottom (Phase I) or on the top only (Phase II) of the combustor liners downstream. Low power configuration uses only pilot-stage injectors. Main-stage injectors are added to high power configuration to help distribute fuel more evenly and achieve lean burn throughout the combustor yielding very low NOx emissions. The ICAO (International Civil Aviation Organization) landing-takeoff NOx emissions are verified to be 88 percent (Phase I) and 76 percent (Phase II) under the ICAO CAEP/6 (Committee on Aviation Environmental Protection 6th Meeting) standard, exceeding the ERA project goal of 75 percent reduction, and the combustors proved to have stable combustion with room to maneuver on fuel flow splits for operability.

  10. Preliminary results of radiation monitoring near uranium mines in Namibia EJOLT Project (DRAFT version)

    Energy Technology Data Exchange (ETDEWEB)

    Chareyron, Bruno

    2012-04-05

    As a part of the EJOLT (Environmental Justice Organizations Liability and Trade) project, EARTHLIFE Namibia and CRIIRAD (Commission for Independent Research and Information about Radiation) have organised visits in areas located in the vicinity of uranium mines in Namibia In the course of an on site mission carried out between September 22 and October 2 2011, scientists from the CRIIRAD laboratory took radiation measurements in situ, and collected 14 samples of top soil, 13 samples of surface sediments of the Swakop, Gawib and Khan rivers, 11 underground water samples in the alluvium of Swakop, and Khan rivers and tap water from Arandis city, and one sample of asparagus. Solid samples have been analysed at the CRIIRAD laboratory in France (measurements performed by HpGe gamma spectrometry) and water samples have been monitored for main chemicals by LDA 26 laboratory in France and for radium 226 and radon 222 at the CRIIRAD laboratory. Some of the preliminary findings are summarised in this report: 1 - The dose rate measured by CRIIRAD on the parking of Roessing mine is about 6 times above natural background value (0.9 {mu}Sv/h compared to 0.15 {mu}Sv/h); 2 - The management of waste rock dumps needs to be improved: Some waste rocks are dumped on the banks of Khan river (at the intersection with Dome Gorge) without fencing and confinement. The radiological impact of this activity has to be studied in detail but preliminary measurements show various impacts on the environment; 3 - The finest fraction of the radioactive tailings dumped on Roessing tailings dam is blown away by the wind and contaminates the surrounding environment; 4 - The high uranium concentration in underground water collected downstream Roessing uranium mine in the Khan river and Swakop river alluvium raises the question of the origin of this uranium

  11. Catsius Clay Project. Calculation and Testing of Behaviour of Unsaturated Clay as Barrier in Radioactive Waste Repositories. Stage 2: Validation Exercises at Laboratory scale

    Energy Technology Data Exchange (ETDEWEB)

    Alonso, E. E.; Alcoverro, J.

    1999-07-01

    Stage 2 of CATSIUS CLAY Project: Validation Exercises at Laboratory Scale includes two Benchmarks, Benchmark 2.1: Oedometer Suction Controlled Tests on Samples of compacted Boom Clay and Benchmark 2.2: Small Scale Weltting-Heating Test on Compacted Bentonite. BM 2.1 had two parts: BM 2.1A (volumetric deformation upon wetting-drying cycles) and BM 2.1 B (swelling pressure test). In BM 2.1A, participants were asked to model the results of a series of five tests on samples of compacted Boom clay. In BM 2.1B, a swelling pressure test in which suction, vertical and horizontal stresses were monitored, was proposed as a blind exercise. Participants were asked to use, without further changes, the models calibrated in BM 2.1A. This exercise provides an evaluation of the capabilities of current mechanical constitutive models for unsaturated clay behaviour. It was found that, even if a calibration exercise on the basis of known experimental data is satisfactory, blind predictions of tests involving different paths may prove difficult. The test set up for BM 2.2 consisted of a stainless stell cell filled with highly expansive compacted bentonite (S2 clay from Almeria, Spain). The clay was subjected to a simultaneous central heating and a progressive water inflow through the botton plate. Temperature at various locations within the sample and the boundary radial stress were monitored throughout the test. Water content distribution was also measured at the end of the experiment. Predictions for this benchmark required the solution of field equations for flow, temperature distribution and mechanical analysis. Model parameters were derived from the extensive set of available experiments on this clay. Comparison between model predictions and measurements revealed the significance of water transport in vapour phase, the difficulties to predict boundary stresses and the general good agreement between measured and calculated temperatures. The report provides a detailed accojnt of the

  12. A pilot project combining multispectral proximal sensors and digital cameras for monitoring tropical pastures

    Science.gov (United States)

    Handcock, Rebecca N.; Gobbett, D. L.; González, Luciano A.; Bishop-Hurley, Greg J.; McGavin, Sharon L.

    2016-08-01

    Timely and accurate monitoring of pasture biomass and ground cover is necessary in livestock production systems to ensure productive and sustainable management. Interest in the use of proximal sensors for monitoring pasture status in grazing systems has increased, since data can be returned in near real time. Proximal sensors have the potential for deployment on large properties where remote sensing may not be suitable due to issues such as spatial scale or cloud cover. There are unresolved challenges in gathering reliable sensor data and in calibrating raw sensor data to values such as pasture biomass or vegetation ground cover, which allow meaningful interpretation of sensor data by livestock producers. Our goal was to assess whether a combination of proximal sensors could be reliably deployed to monitor tropical pasture status in an operational beef production system, as a precursor to designing a full sensor deployment. We use this pilot project to (1) illustrate practical issues around sensor deployment, (2) develop the methods necessary for the quality control of the sensor data, and (3) assess the strength of the relationships between vegetation indices derived from the proximal sensors and field observations across the wet and dry seasons. Proximal sensors were deployed at two sites in a tropical pasture on a beef production property near Townsville, Australia. Each site was monitored by a Skye SKR-four-band multispectral sensor (every 1 min), a digital camera (every 30 min), and a soil moisture sensor (every 1 min), each of which were operated over 18 months. Raw data from each sensor was processed to calculate multispectral vegetation indices. The data capture from the digital cameras was more reliable than the multispectral sensors, which had up to 67 % of data discarded after data cleaning and quality control for technical issues related to the sensor design, as well as environmental issues such as water incursion and insect infestations. We recommend

  13. EC MoDeRn Project: In-situ Demonstration of Innovative Monitoring Technologies for Geological Disposal - 12053

    Energy Technology Data Exchange (ETDEWEB)

    Breen, B.J. [NDA, Herdus House, Westlakes Science and Technology Park, Moor Row, Cumbria, CA24 3HU (United Kingdom); Garcia-Sineriz, J.L. [AITEMIN, c/Margarita Salas 14-Parque Leganes Tecnologico-Leganes, ES-28918, Madrid (Spain); Maurer, H. [ETH Zurich, ETH Honggerberg, CH-8093, Zurich (Switzerland); Mayer, S. [ANDRA, 1-7 rue Jean-Monnet, F-92298 Chatenay-Malabry cedex (France); Schroeder, T.J. [NRG, P.O. Box 25, NL-1755 ZG Petten (Netherlands); Verstricht, J. [EURIDICE EIG, c/o SCK.CEN, Boeretang 200, BE-2400 Mol (Belgium)

    2012-07-01

    Monitoring to provide information on the evolution of geological disposal presents several challenges. The 4-year, euros M 5, EC MoDeRn Project (http://www.modern-fp7.eu/), which commenced in 2009, addresses monitoring processes, state-of-the-art technology and innovative research and development of monitoring techniques. This paper discusses some of the key drivers for the development of innovative monitoring techniques and provides outlines of the demonstration programmes being conducted within MoDeRn. The aim is to develop these innovative monitoring techniques and to demonstrate them under realistic conditions present in underground laboratories. These demonstration projects, applying a range of different monitoring techniques, are being carried out at underground research facilities in different geological environments at HADES URL in Belgium (plastic clay), Bure in France (indurated clay) and at Grimsel Test Site (granite) in Switzerland. These are either built upon existing infrastructure (EC ESDRED Low pH shotcrete and TEM experiments at Grimsel; and PRACLAY experiment and underground galleries in HADES) or will be attached to infrastructure that is being developed and financed by resources outside of this project (mock-up disposal cell in Bure). At Grimsel Test Site, cross-hole and hole-to-tunnel seismic methods are being employed as a means to monitor induced changes in an artificially saturated bentonite wall confined behind a shotcrete plug. Recognising the limitations for travel-time tomography for monitoring a disposal cell, full waveform inversion techniques are being employed to enhance the capacity to monitor remote from the excavation. At the same Grimsel location, an investigation will be conducted of the potential for using a high frequency wireless (HFW) sensor network embedded within the barrier system; this will include the possibility of providing energy remotely to isolated sensors. At the HADES URL, the monitoring programme will utilise

  14. Project Catch: A space based solution to combat illegal, unreported and unregulated fishing. Part I: Vessel monitoring system

    Science.gov (United States)

    Detsis, Emmanouil; Brodsky, Yuval; Knudtson, Peter; Cuba, Manuel; Fuqua, Heidi; Szalai, Bianca

    2012-11-01

    Space assets have a unique opportunity to play a more active role in global resource management. There is a clear need to develop resource management tools in a global framework. Illegal, Unregulated and Unreported (IUU) fishing is placing pressure on the health and size of fishing stocks around the world. Earth observation systems can provide fishery management organizations with cost effective monitoring of large swaths of ocean. Project Catch is a fisheries management project based upon the complimentary, but independent Catch-VMS and Catch-GIS systems. Catch-VMS is a Vessel Monitoring System with increased fidelity over existing offerings. Catch-GIS is a Geographical Information System that combines VMS information with existing Earth Observation data and other data sources to identify Illegal, Unregulated and Unreported (IUU) fishing. Project Catch was undertaken by 19 Masters students from the 2010 class of the International Space University. In this paper, the space-based system architecture of Project Catch is presented and analyzed. The rationale for the creation of the system, as well as the engineering trade-off studies in its creation, are discussed. The Catch-VMS proposal was envisaged in order to address two specific problems: (1) the expansion of illegal fishing to high-latitude regions where existing satellite systems coverage is an issue and (2) the lack of coverage in remote oceanic regions due to reliance on coastal-based monitoring. Catch-VMS utilizes ship-borne transponders and hosted-payload receivers on a Global Navigation Satellite System in order to monitor the position and activity of compliant fishing vessels. Coverage is global and continuous with multiple satellites in view providing positional verification through multilateration techniques. The second part of the paper briefly describes the Catch-GIS system and investigates its cost of implementation.

  15. Project SIMORAC: a wireless system for radiation monitoring in emergencies; Proyecto SIMORAC: Un sistema inalambrico para monitorizacion radiologica en emergencias

    Energy Technology Data Exchange (ETDEWEB)

    Gomez, D.; Serrano, J. L.; Cabrera, E.; Barbaran, J.; Llopis, L.; Diaz, M.

    2013-07-01

    The SIMORAC project includes a new system for Radiological monitoring using wireless sensor networks (RSIs), without infrastructure planning in emergency situations for a rapidly deployable by air or land, with the aim of providing a tool emergency teams capable of offering a real time x-ray map within the radius of action of an accident. Communication of quality at a great distance, resistance to weather, long autonomy and possibility of aerial deployment are some of the features of SIMORAC.

  16. SPECT/CT for staging and treatment monitoring in oncology. Applications in differentiated thyroid cancer and liver tumors; SPECT/CT zum initialen Staging und Therapiemonitoring in der Onkologie. Indikationen beim differenzierten Schilddruesenkarzinom und bei Lebertumoren

    Energy Technology Data Exchange (ETDEWEB)

    Weber, K.; Berger, F.; Reiser, M.F. [Klinikum der Ludwig-Maximilians-Universitaet Muenchen, Campus Innenstadt, Institut fuer Klinische Radiologie, Muenchen (Germany); Mustafa, M.; Bartenstein, P.; Haug, A. [Klinikum der Ludwig-Maximilians-Universitaet Muenchen, Campus Grosshadern, Klinik und Poliklinik fuer Nuklearmedizin, Muenchen (Germany)

    2012-07-15

    Hybrid imaging of function and morphology has gained significant importance for lesion detection and treatment monitoring in oncology. In patients with differentiated thyroid carcinoma (DTC) a planar whole body scan is carried out after radioiodine therapy (RIT) for staging. However, due to limited spatial resolution the diagnostic accuracy of this scintigraphy method is impaired. Radioembolization utilizing {sup 90}Yttrium loaded micro-spheres by selective internal radiotherapy (SIRT) allows a minor invasive therapy of primary and secondary liver tumors. In order to avoid side effects of the micro-spheres caused by an outflow into intestines, stomach or lungs, imaging the arteries supplying the liver has to be performed by means of technetium-99m macroaggregated albumin ({sup 99m}Tc-MAA) and scintigraphy. The limited morphological information supplied by scintigraphy is again a challenge in treatment monitoring. {sup 131}Iodine whole body scanning is used for staging in patients with DTC 3-4 days after ablation. Monitoring of the tumor marker thyroglobulin and selective radioiodine whole body scans are available for patients with a high risk profile in the further follow-up with imaging of the arteries supplying the liver by means of {sup 99m}Tc-MAA scintigraphy in preparation of SIRT. Single photon emission computed tomography/computed tomography (SPECT/CT) of the neck and thorax with a therapeutic activity of radioiodine for staging after ablation. Techniques include imaging of arteries supplying the liver by means of {sup 99m}Tc-MAA SPECT/CT before SIRT and evaluation and quantification of the uptake of liver tumors, especially in comparison to the uptake of liver parenchyma by means of SPECT/CT. Due to the integration of combined functional and morphological information SPECT/CT can be used to characterize the morphology and iodine uptake of lesions more accurately, resulting in optimized staging in patients with DTC in comparison to whole body iodine scans

  17. Study of the Cherokee Nuclear Station: projected impacts, monitoring plan, and mitigation options for Cherokee County, South Carolina

    Energy Technology Data Exchange (ETDEWEB)

    Peelle, E.; Schweitzer, M.; Scharre, P.; Pressman, B.

    1979-07-01

    This report inventories Cherokee County's capabilities and CNS project characteristics, projects expected impacts from the interaction of the two defines four options for Cherokee County decision makers, and presents a range of possible mitigation and monitoring plans for dealing with the problems identified. The four options and general implementation guidelines for each are presented after reviewing pertinent features of other mitigation and monitoring plans. The four options include (1) no action, (2) preventing impacts by preventing growth, (3) selective growth in designated areas as services can be supplied, and (4) maximum growth designed to attract as many in-movers as possible through a major program of capital investiments in public and private services. With the exception of the no action option, all plans deal with impacts according to some strategy determined by how the County wishes to manage growth. Solutions for impact problems depend on which growth strategy is selected and what additional resources are secured during the impact period. A monitoring program deals with the problems of data and projections uncertainty, while direct action is proposed to deal with the institutional problems of delay of the needed access road, timeing and location problems from the tax base mismatch, and lack of local planning capability.

  18. Community monitoring of integrated pest management versus conventional pesticide use in a World Bank project in Indonesia.

    Science.gov (United States)

    Ishii-Eiteman, Marcia J; Ardhianie, Nila

    2002-01-01

    Pesticide Action Network North America (PANNA) collaborated with a local Indonesian nongovernmental organization (NGO), Yayasan Duta Awam (YDA), in monitoring impacts of the World Bank-financed Integrated Swamps Development Project (ISDP). This paper reports the results of the community-based investigation, which found wide disparities between the World Bank's policy on pest management and its implementation. Instead of reducing farmers' reliance on pesticides as required, the ISDP led to increased intensity and frequency of pesticide use and adverse health and environmental effects from pesticide exposures. YDA and PANNA presented the findings to the Indonesian government and World Bank officials, and farmers requested training in IPM among other recommendations. After NGOs undertook joint advocacy efforts to reduce pesticide dependence in the project, the World Bank withdrew hazardous pesticides from input packages, IPM training was initiated, and community monitors became local leaders in their villages. The study demonstrates the importance and efficacy of independent community-based monitoring in documenting pesticide problems and replacing pesticides with IPM in World Bank development projects.

  19. Did dead animals really spew from the IEA-GHG Weyburn-Midale CO2 monitoring and storage project?

    Science.gov (United States)

    Rostron, B. J.; IEA-GHG Weyburn-Midale CO2 Project, T.; Theme Leaders: IEA-GHG Weyburn-Midale CO2 Monitoring; Storage Project

    2011-12-01

    The IEA-GHG Weyburn-Midale CO2 monitoring and storage project was initiated in 2000 to study the geological storage of CO2 as part of a CO2-EOR project in the Weyburn Field in Saskatchewan, Canada. Initial injection of CO2 began in October 2000, and continues to date, with more than 18 Mtonnes of anthropogenic CO2 stored in the Weyburn reservoir. In January 2011, a local landowner supported by a consultant's soil gas survey, claimed they had conclusive proof that the "source of the high concentrations of CO2 in soils ... is clearly the anthropogenic CO2 injected into the Weyburn reservoir". These claims quickly attracted local, provincial, national, and international media attention alerting the world to the "leakage" at the Weyburn CO2-EOR project and furthermore calling into question the safety of geological CO2 sequestration in general. A careful look at the data reveals a different story. Twenty six soil gas samples were collected in August 2010, from shallow (Weyburn-Midale research project, do not support the claim(s) of anthropogenic CO2 leakage from the Weyburn reservoir. A comprehensive geological, geophysical, hydrogeological, and geochemical site characterization combined with background and on-site soil gas monitoring, integrated with numerical simulations of CO2 movement has not detected any evidence of migration of CO2 above the regional subsurface seal. Shallow soil gas monitoring near the Weyburn field, and in the CO2-EOR area, have detected transient elevated CO2 concentrations of similar magnitudes. Previously published 13C/12C data from shallow aquifers in Saskatchewan match those obtained by the consultant. None of the observed geochemical parameter values fall outside the background ranges expected for this area. Phenomena observed at this site can be explained by near surface processes including microbial generation of soil CO2 and methane. This talk will highlight relevant data collected by the research project and contrast it with claims of

  20. The INSIDE project: on-line monitoring and simulation validation with the in-beam PET scanner

    Science.gov (United States)

    Ferrero, V.; INSIDE Collaboration

    2017-05-01

    The quality assurance of particle therapy treatment is a fundamental issue that can be addressed by developing reliable monitoring techniques and indicators of the treatment plan accuracy. Monitoring using Position Emission Tomography (PET) systems is the only in-vivo non invasive technique employed clinically and has been carried out in particle therapy since 1997. However, the PET monitoring of β + emitter isotopes is typically done after the treatment, resulting in a large fraction of lost data because of the isotopes rapid physical decay. The INSIDE collaboration has recently installed an in-beam PET scanner at the Italian National Center of Oncologic Hadrontherapy in Pavia, Italy. Here, there is an ongoing project in order to start testing the method on patients. This work focuses on the online performances of the scanner with clinical beams.

  1. British Columbia S-2000 monitoring project. Volume 1: Performance summary interim report for the period June 1993 to December 1993

    Energy Technology Data Exchange (ETDEWEB)

    Makuch, P.D.; Harrison, S.J

    1994-02-01

    The Canadian S-2000 program was established to provide utilities with comprehensive field trials of solar domestic hot water (SDHW) heating systems, which have been identified as potentially able to provide significant energy savings. The main objective of S-2000 is to promote cooperation between governments and electrical utilities interested in evaluating whether SDHW systems are suited to utility load management goals, particularly the reduction of peak demand levels and pollutant emission control through cost-effective energy displacement. Current activity in the program consists of cooperative government/utility pilot projects to install and monitor several SDHW systems across Canada. As a first step to demonstrate the potential of SDHW in British Columbia, eight systems were purchased by provincial utilities, installed at private residences, and monitored. The monitoring results over the June-December 1993 period are summarized. Six of the systems are functioning as expected and show an average solar fraction of 42.2% over the monitoring period. These systems show good agreement with predicted results, but the two remaining systems are operating below projected levels due to equipment malfunctions. Only three of the systems had a daily load greater than the 239 l/d average for a typical Canadian family. Calculations indicate that a home using 350 l/d of hot water and a properly oriented collector should get 45.7% of the hot water heating load from solar energy (11.1 GJ of the 27.3 GJ total annual load). 4 refs., 18 figs., 11 tabs.

  2. Sustainable and non-conventional monitoring systems to mitigate natural hazards in low income economies: the 4onse project approach.

    Science.gov (United States)

    Cannata, Massimiliano; Ratnayake, Rangajeewa; Antonovic, Milan; Strigaro, Daniele

    2017-04-01

    Environmental monitoring systems in low economies countries are often in decline, outdated or missing with the consequence that there is a very scarce availability and accessibility to these information that are vital for coping and mitigating natural hazards. Non-conventional monitoring systems based on open technologies may constitute a viable solution to create low cost and sustainable monitoring systems that may be fully developed, deployed and maintained at local level without lock-in dependances on copyrights or patents or high costs of replacements. The 4onse research project , funded under the Research for Development program of the Swiss National Science Foundation and the Swiss Office for Development and Cooperation, propose a complete monitoring system that integrates Free & Open Source Software, Open Hardware, Open Data, and Open Standards. After its engineering, it will be tested in the Deduru Oya catchment (Sri Lanka) to evaluate the system and develop a water management information system to optimize the regulation of artificial basins levels and mitigate flash floods. One of the objective is to better scientifically understand strengths, criticalities and applicabilities in terms of data quality; system durability; management costs; performances; sustainability. Results, challenges and experiences from the first six months of the projects will be presented with particular focus on the activities of synergies building and data collection and dissemination system advances.

  3. Flexible High Energy-Conversion Sensing Materials for Structural Health Monitoring Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The applicant is developing flexible highly-efficient piezoelectric materials for use in structural health monitoring (SHM) as contemplated in the solicitation...

  4. Highly Reliable Structural Health Monitoring of Smart Composite Vanes for Jet Engine Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Intelligent Fiber Optic Systems and Auburn University propose a Fiber Bragg Grating (FBG) integrated Structural Health Monitoring (SHM) sensor system capable of...

  5. Highly Reliable Structural Health Monitoring of Smart Composite Vanes for Jet Engine Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In Phase 1, Intelligent Fiber Optic Systems (IFOS) successfully demonstrated a Fiber Bragg Grating (FBG) based integrated Structural Health Monitoring (SHM) sensor...

  6. Structural Health Monitoring with Fiber Bragg Grating and Piezo Arrays Project

    Data.gov (United States)

    National Aeronautics and Space Administration — IFOS and its research institute collaborator, Washington State University (WSU), have demonstrated feasibility of a structural health monitoring (SHM) system for...

  7. Nonlinear guided wave circular array system for microcrack monitoring in spacecraft Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Reliable monitoring of the microcrack formation in the complex composite structure components in NASA spacecraft and launch vehicles is critical for vehicle...

  8. Summary of environmental flow monitoring for the Sustainable Rivers Project on the Middle Fork Willamette and McKenzie Rivers, western Oregon, 2014–15

    Science.gov (United States)

    Jones, Krista L.; Mangano, Joseph F.; Wallick, J. Rose; Bervid, Heather D.; Olson, Melissa; Keith, Mackenzie K.; Bach, Leslie

    2016-11-07

    This report presents the results of an ongoing environmental flow monitoring study by The Nature Conservancy (TNC), U.S. Army Corps of Engineers (USACE), and U.S. Geological Survey in support of the Sustainable Rivers Project (SRP) of TNC and USACE. The overarching goal of this study is to evaluate and characterize relations between streamflow, geomorphic processes, and black cottonwood (Populus trichocarpa) recruitment on the Middle Fork Willamette and McKenzie Rivers, western Oregon, that were hypothesized in earlier investigations. The SRP can use this information to plan future monitoring and scientific investigations, and to help mitigate the effects of dam operations on streamflow regimes, geomorphic processes, and biological communities, such as black cottonwood forests, in consultation with regional experts. The four tasks of this study were to:Compare the hydrograph from Water Year (WY) 2015 with hydrographs from WYs 2000–14 and the SRP flow recommendations,Assess short-term and system-wide changes in channel features and vegetation throughout the alluvial valley section of the Middle Fork Willamette River (2005–12),Examine changes in channel features and vegetation over two decades (1994–2014) for two short mapping zones on the Middle Fork Willamette and McKenzie Rivers, andComplete a field investigation of summer stage and the growth of black cottonwood and other vegetation on the Middle Fork Willamette and McKenzie Rivers in summer 2015.

  9. Monitoring systems and their effectiveness for project cost control in construction

    NARCIS (Netherlands)

    Al-Jibouri, Saad H.

    2002-01-01

    This paper reports on a research to investigate the effectiveness of some commonly used monitoring systems, in detecting deviations from the planned cost and performance. The monitoring systems used in this work are: Leading parameter technique Variances method Activity based ratios technique Th

  10. Monitoring of DNA breakage in embryonic stages of the African catfish Clarias gariepinus (Burchell, 1822) after exposure to lead nitrate using alkaline comet assay.

    Science.gov (United States)

    Osman, Alaa G M; Mekkawy, Imam A; Verreth, Johan; Wuertz, Sven; Kloas, Werner; Kirschbaum, Frank

    2008-12-01

    Increasing lead contamination in Egyptian ecosystems and high lead concentrations in food items have raised concern for human health and stimulated studies on monitoring ecotoxicological impact of lead-caused genotoxicity. In this work, the alkaline comet assay was modified for monitoring DNA strand breakage in sensitive early life stages of the African catfish Clarias gariepinus. Following exposure to 100, 300, and 500 microg/L lead nitrate, DNA strand breakage was quantified in embryos at 30, 48, 96, 144, and 168 h post-fertilization (PFS). For quantitative analysis, four commonly used parameters (tail % DNA, %TDNA; head % DNA, %HDNA; tail length, TL; tail moment, TM) were analyzed in 96 nuclei (in triplicates) at each sampling point. The parameter %TDNA revealed highest resolution and lowest variation. A strong correlation between lead concentration, time of exposure, and DNA strand breakage was observed. Here, genotoxicity detected by comet assay preceded the manifested malformations assessed with conventional histology. Qualitative evaluation was carried out using five categories are as follows: undamaged (%TDNA 75%) nuclei confirming a dose and time-dependent shift towards increased frequencies of highly and extremely damaged nuclei. A protective capacity provided by a hardened chorion is a an interesting finding in this study as DNA damage in the prehatching stages 30 h-PFS and 48 h-PFS was low in all treatments (qualitative and quantitative analyses). These results clearly show that the comet assay is a sensitive tool for the detection of genotoxicity in vulnerable early life stages of the African catfish and is a method more sensitive than histological parameters for monitoring genotoxic effects.

  11. Efficient monitoring of blood-stage infection in a malaria rodent model by the rotating-crystal magneto-optical method

    CERN Document Server

    Orban, Agnes; Albuquerque, Inês S; Butykai, Adam; Kezsmarki, Istvan; Hänscheid, Thomas

    2015-01-01

    Global research efforts have been focused on the simultaneous improvement of the efficiency and sensitivity of malaria diagnosis in resource-limited settings and for the active case detection of asymptomatic infections. A recently developed magneto-optical (MO) method allows the high-sensitivity detection of malaria pigment (hemozoin) crystals in blood via their magnetically induced rotational motion. The evaluation of the method using synthetic $\\beta$-hematin crystals and P. falciparum in vitro cultures implies its potential for in-field diagnosis. Here, we study the performance of the method in monitoring the in vivo onset and progression of the blood stage infection using a malaria mouse model. We found that the MO method can detect the first generation of intraerythrocytic parasites at the ring stage 61-66 hours after sporozoite injection demonstrating better sensitivity than light microscopy and flow cytometry. MO measurements performed after treatment of severe P. berghei infections show that the clear...

  12. Atmosphere Resource Recovery & Environmental Monitoring (ARREM) for Long Duration Exploration Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The project focuses on key physico-chemical process technologies for Atmosphere Revitalization Systems (ARS) that increase reliability, capability, and consumable...

  13. Measuring the adoption of consistent use of condoms using the stages of change model. AIDS Community Demonstration Projects.

    Science.gov (United States)

    Schnell, D J; Galavotti, C; Fishbein, M; Chan, D K

    1996-01-01

    The stages of behavior change model has been used to understand a variety of health behaviors. Since consistent condom use has been promoted as a risk-reduction behavior for prevention of human immunodeficiency virus (HIV) infection, an algorithm for staging the adoption of consistent condom use during vaginal sex was empirically developed using three considerations: HIV prevention efficacy, analogy with work on staging other health-related behaviors, and condom use data from groups at high risk for HIV infection. This algorithm suggests that the adoption of consistent condom use among persons at high risk can be meaningfully measured with the model. However, variations in the algorithm details affect both the interpretation of stages and apportionment of persons across stages.

  14. Yakima River Species Interactions Studies; Yakima/Klickitat Fisheries Project Monitoring and Evaluation, 2004-2005 Annual Report.

    Energy Technology Data Exchange (ETDEWEB)

    Pearsons, Todd N.; Temple, Gabriel M.; Fritts, Anthony L. (Washington Department of Fish and Wildlife, Olympia, WA)

    2005-05-01

    This report is intended to satisfy two concurrent needs: (1) provide a contract deliverable from the Washington Department of Fish and Wildlife (WDFW) to the Bonneville Power Administration (BPA), with emphasis on identification of salient results of value to ongoing Yakima/Klickitat Fisheries Project (YKFP) planning, and (2) summarize results of research that have broader scientific relevance. This is the thirteenth of a series of progress reports that address species interactions research and supplementation monitoring of fishes in response to supplementation of salmon and steelhead in the upper Yakima River basin (Hindman et al. 1991; McMichael et al. 1992; Pearsons et al. 1993; Pearsons et al. 1994; Pearsons et al. 1996; Pearsons et al. 1998, Pearsons et al. 1999, Pearsons et al. 2001a, Pearsons et al. 2001b, Pearsons et al. 2002, Pearsons et al. 2003, Pearsons et al. 2004). Journal articles and book chapters have also been published from our work (McMichael 1993; Martin et al. 1995; McMichael et al. 1997; McMichael and Pearsons 1998; McMichael et al. 1998; Pearsons and Fritts 1999; McMichael et al. 1999; McMichael et al. 1999; Pearsons and Hopley 1999; Ham and Pearsons 2000; Ham and Pearsons 2001; Amaral et al. 2001; McMichael and Pearsons 2001; Pearsons 2002, Fritts and Pearsons 2004, Pearsons et al. in press, Major et al. in press). This progress report summarizes data collected between January 1, 2004 and December 31, 2004. These data were compared to findings from previous years to identify general trends and make preliminary comparisons. Interactions between fish produced as part of the YKFP, termed target species or stocks, and other species or stocks (non-target taxa) may alter the population status of non-target species or stocks. This may occur through a variety of mechanisms, such as competition, predation, and interbreeding (Pearsons et al. 1994; Busack et al. 1997; Pearsons and Hopley 1999). Furthermore, the success of a supplementation program may

  15. Case Study on the Deficiencies and Difficulties of Project Management since the Promotion Stage of Integrated Waste Systems

    Directory of Open Access Journals (Sweden)

    Raluca CUCINSCHI

    2011-06-01

    Full Text Available The present case study focuses on the shortcomings and difficulties encountered in the management of projects in the environment protection area, respectively of integrated waste management systems, observed in similar projects, promoted simultaneously in five counties in Romania, counties located in different development regions. Thus, following a European funding, five counties were selected to receive free consultancy services for the elaboration of the county master in the field of environment protection, respectively waste management. One of the requirements that the counties had to fulfil was the expressed unequivocal willingness to implement the project at county level. A Project Implementation Unit (PIU was set up at county council level with the precise purpose of managing and implementing the project. Even though the counties benefited from free technical assistance, major delays in finalizing and approving the application were encountered in all the cases studied, due to reasons that depended mostly on the manner the project management was conducted.

  16. The Multi-Isotope Process Monitor Project: FY11 Progress and Accomplishments

    Energy Technology Data Exchange (ETDEWEB)

    Orton, Christopher R.; Fraga, Carlos G.; Hayes, John W.; Schwantes, Jon M.; Bender, Sarah E.; Unlu, Kenan; Dayman, Kenneth J.; Schreiber, S. S.; Landsberger, Sheldon

    2012-08-01

    Summary The Multi-Isotope Process (MIP) Monitor represents a potentially new and efficient approach to monitoring process conditions in reprocessing facilities with the high-level goal of aiding in the “...(minimization of) the risks of nuclear proliferation and terrorism” (Office of Technology Assessment 1995). This approach relies on multivariate analysis and gamma spectroscopy of spent fuel product and waste streams to automatically and simultaneously monitor a variety of process conditions (e.g., acid concentrations, burnup, cooling time, etc.) in near real-time (NRT). While the conceptual basis for the MIP Monitor has been shown to be effective in an aqueous reprocessing system, the fundamental approach should also be viable in a pyro-processing recycle system. The MIP Monitor may be calibrated to provide online quantitative information about process variables for process control or domestic safeguards applications; or it can simply monitor, with a built-in information barrier, for off-normal conditions in process streams, making the approach well-suited for applications were it is necessary to respect proprietary information or for international safeguards applications. Proof-of-concept simulations and experiments were performed in previous years demonstrating the validity of this tool in a laboratory setting. This report details follow-on research and development efforts sponsored by the U.S. Department of Energy Fuel Cycle Research and Development (FCR&D) related to the MIP Monitor for fiscal year 2011 (FY11).

  17. The Multi-Isotope Process (MIP) Monitor Project: FY12 Progress and Accomplishments

    Energy Technology Data Exchange (ETDEWEB)

    Coble, Jamie B.; Orton, Christopher R.; Jordan, David V.; Schwantes, Jon M.; Bender, Sarah; Dayman, Kenneth J.; Unlu, Kenan; Landsberger, Sheldon

    2012-09-27

    The Multi-Isotope Process (MIP) Monitor, being developed at Pacific Northwest National Laboratory (PNNL), provides an efficient approach to monitoring the process conditions in reprocessing facilities in support of the goal of "...(minimization of) the risks of nuclear proliferation and terrorism." The MIP Monitor measures distributions of a suite of indicator (radioactive) isotopes present within product and waste streams of a nuclear reprocessing facility. These indicator isotopes are monitored on-line by gamma spectrometry and compared, in near-real-time, to spectral patterns representing "normal" process conditions using multivariate pattern recognition software. The monitor utilizes this multivariate analysis and gamma spectroscopy of reprocessing streams to detect small changes in the gamma spectrum, which may indicate changes in process conditions. Multivariate analysis methods common in chemometrics, such as principal component analysis (PCA) and partial least squares regression (PLS), act as pattern recognition techniques, which can detect small deviations from the expected, nominal condition. By targeting multiple gamma-emitting indicator isotopes, the MIP Monitor approach is compatible with the use of small, portable, relatively high-resolution gamma detectors that may be easily deployed throughout an existing facility. The automated multivariate analysis can provide a level of data obscurity, giving a built-in information barrier to protect sensitive or proprietary operational data. Proof-of-concept simulations and experiments have been performed in previous years to demonstrate the validity of this tool in a laboratory setting. Development of the MIP Monitor approach continues to evaluate the efficacy of the monitor for automated, real-time or near-real-time application. This report details follow-on research and development efforts sponsored by the U.S. Department of Energy Fuel Cycle Research and Development related to the MIP Monitor for fiscal year

  18. Communication Pathways in the Light Water Reactor Sustainability Online Monitoring Project

    Energy Technology Data Exchange (ETDEWEB)

    Nancy J. Lybeck; Magdy S. Tawfik; Binh T. Pham; Vivek Agarwal; Jamie Coble

    2011-09-01

    Implementation of online monitoring and prognostics in existing U.S. nuclear power plants will involve coordinating the efforts of national laboratories, utilities, universities, and private companies. Large amounts of operational data, including failure data, are necessary for the development and calibration of diagnostic and prognostic algorithms. The ability to use data from all available resources will provide the most expeditious avenue to implementation of online monitoring in existing NPPs; however, operational plant data are often considered proprietary. Secure methods for transferring and storing data are discussed, along with a potential technology for implementation of online monitoring.

  19. Technology projects for characterization--monitoring of volatile organic compounds (VOCs)

    Energy Technology Data Exchange (ETDEWEB)

    Junk, G.A.; Haas, W.J. Jr.

    1992-07-01

    One hundred thirty technology project titles related to the characterization of volatile organic compounds (VOCs) at an arid site are listed alphabetically by first contact person in a master compilation that includes phone numbers, addresses, keywords, and short descriptions. Separate tables are presented for 62 field-demonstrated, 36 laboratory-demonstrated, and 35 developing technology projects. The technology projects in each of these three categories are also prioritized in separate summary tables. Additional tables are presented for a number of other categorizations of the technology projects: In Situ; Fiberoptic; Mass Spectrometer; Optical Spectroscopy; Raman or SERS; Ion Mobility or Acoustic; Associated; and Commercial. Four lists of contact person names are provided so details concerning the projects that deal with sampling, and VOCs in gases, waters, and soils (sediments) can be obtained. Finally, seven wide-ranging conclusions based on observations and experiences during this work are presented.

  20. European collaboration for improved monitoring of Icelandic volcanoes: Status of the FUTUREVOLC project after the initial 18 months

    Science.gov (United States)

    Dumont, Stéphanie; Parks, Michelle; Sigmundsson, Freysteinn; Vogfjörð, Kristín; Einarsdóttir, Heiðveig Maria; Tumi Gudmundsson, Magnús; Kristinsson, Ingvar; Loughlin, Sue; Ilyinskaya, Evgenia; Hooper, Andrew; Kylling, Arve; Witham, Claire; Bean, Chris; Braiden, Aoife; Ripepe, Maurizio; Prata, Fred; Pétur Heiðarsson, Einar; Other Members Of The Futurevolc Team

    2014-05-01

    The FUTUREVOLC project funded by the European Union (FP7) is devoted to volcanic hazard assessment and establishing an integrated volcanological monitoring procedure through a European collaboration. To reach these objectives the project combines broad expertise from 26 partners from 10 countries, focusing on the four most active volcanoes of Iceland: Grímsvötn, Katla, Hekla and Bárdarbunga. The geological setting of Iceland, the high rate of eruptions and the various eruption styles make this country an optimal natural laboratory to study volcanic processes from crustal depths to the atmosphere. The project, which began on 1 October 2012, integrates advanced monitoring and analytical techniques in an innovative way, focusing on (i) detailed monitoring to improve our understanding of the seismic/magmatic unrest, in order to estimate the amount of magma available for an eruption and to provide early warnings (ii) the dynamics of magma in the conduit and a near real time estimation of the mass eruption rate and (iii) observing and modelling the plume dynamics. The project design considers effective collaboration between partners and aims for efficient cross-disciplinary workflows. A major step during the first 18 months of the project was the installation of additional equipment in the volcanic regions of Iceland to reinforce and complement the existing monitoring. The instruments include: seismometers, GPS stations, MultigGAS detectors, DOAS, infrasonic arrays, electric field sensors, radars, and optical particle sizers. Data streaming is designed to withstand extreme weather conditions. The FUTUREVOLC project has an open data policy for real and near-time data. Implementation of a data hub is currently under way, based on open access to data from the 2010 Eyjafjallajökull eruption. Access to volcano monitoring data through a common interface will allow timely information on magma movements facilitated through combined analysis. A key part of the project is to

  1. 浅谈设计阶段工程造价的控制%Analysis on project cost controlling in designing stage

    Institute of Scientific and Technical Information of China (English)

    南暄

    2009-01-01

    针对设计阶段的工程造价控制是工程造价控制的重点,在工程设计阶段造价控制现状分析的基础上,进一步提出了工程设计阶段造价控制的措施,以使设计阶段的工程造价得到较为合理的控制.%Since the cost controlling in designing stage is the focal point of project cost controlling, the paper proposes measures for cost control-ling in designing stage on base of analysis about the present situation of cost controlling, it aims to control the cost in designing stage reason-ably.

  2. Time Reversal Acoustic Structural Health Monitoring Using Array of Embedded Sensors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Time Reversal Acoustic (TRA) structural health monitoring with an embedded sensor array represents a new approach to in-situ nondestructive evaluation of air-space...

  3. Space Qualified Non-Destructive Evaluation and Structural Health Monitoring Technology Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NextGen Aeronautics is proposing an innovative space qualified non-destructive evaluation and health monitoring technology. The technology is built on concepts...

  4. In-Situ Real-Time Temperature Monitoring of Thermal Protection Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This program addresses the need for interfacial and in-depth temperature monitoring of thermal protection systems (TPS). Novel, linear drive, eddy current methods...

  5. A Miniaturized Sensor for Microbial Monitoring of Spacecraft Water Environment Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Accurate real-time microbial monitoring of water environment is of paramount importance to crew health as well as to ensure proper functioning and control of the...

  6. Unpowered Wireless Ultrasound Generation and Sensing for Structural Health Monitoring of Composites Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Damage detection based on ultrasonic waves is one of the most popular inspection schemes employed by many structural health monitoring (SHM) systems. We propose a...

  7. Use of the Operational Air Quality Monitor (AQM) for In-Flight Water Testing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Currently, the Air Quality Monitor (AQM) on-board ISS provides specific information for a number of target compounds in the air. However, there is a significant...

  8. Tunable Laser Development for In-flight OFDR Structural Health Monitoring Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Development of a cost-effective, robust, tunable, miniaturized, ruggedized, and flight tested swept laser for in-flight structural health monitoring. The objective...

  9. A Miniaturized Sensor for Microbial Monitoring of Spacecraft Water Environment Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Accurate real-time microbial monitoring of water environment is of paramount importance to crew health as well as to ensure proper functioning and control of the...

  10. Aircraft Engine Life-Consumption Monitoring for Real-Time Reliability Determination Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The object of this research is to develop an in-service life-monitor system for the prediction of the remaining component and system life of aircraft engines. The...

  11. In-Service Aircraft Engine System Life Monitor Using Advanced Life-Estimating Technique Project

    Data.gov (United States)

    National Aeronautics and Space Administration — It is proposed to develop an accurate in-service aircraft engine life monitor system for the prediction of remaining component and system life for aircraft engines....

  12. Lightweight, Wearable Metal Rubber-Textile Sensor for In Situ Lunar Autonomous Health Monitoring Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NanoSonic proposes to develop a low-weight, non-invasive in situ autonomous health-monitoring system for crewmembers' lunar extravehicular activity (EVA). This novel...

  13. Combustion/Emission Species Monitoring Ground and Flight Aeronautical Research Using a Gas Microsensor Array Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The goal of this program is to develop a miniaturized and in-situ operated gas microsensor array for the real time monitoring of chemical composition of turbine...

  14. Ullage Compatible Optical Sensor for Monitoring Safety-Significant Malfunctions Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The tasks of this Phase I proposal are designed to establish the feasibility of an optical sensor for real-time, in situ monitoring of the ullage environment of an...

  15. High Sensitivity Pulsed Laser Vibrometer for Aircraft Interior Noise Monitoring Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose an innovative pulsed laser vibrometer technology for the monitoring of interior noise inside an aircraft. The optical speckle-tolerant nature of the...

  16. Lightweight, Wearable Metal Rubber-Textile Sensor for In-Situ Lunar Autonomous Health Monitoring Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This NASA Phase II SBIR program would develop comfortable garments with multiple integrated sensor functions for the monitoring of astronauts during long duration...

  17. Data Description Exchange Services for Heterogeneous Vehicle and Spaceport Control and Monitor Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — CCT has designed and prototyped, as part of the Phase-1 SBIR, a generic platform independent software capability for exchange of semantic control and monitoring...

  18. The SUCIMA project: A status report on high granularity dosimetry and proton beam monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Caccia, M. [Dipartimento di Scienze CC.FF.MM., Universita dell' Insubria, Como (Italy)]. E-mail: Massimo.Caccia@uninsubria.it; Badano, L. [Fondazione per Adroterapia Oncologica, Novara (Italy); Berst, D. [Laboratoire d' Electronique et de Physique des Systemes Instrumentaux, Universite Luis Pasteur, Strasbourg (France); Centre National de la Recherce Scientifique/IN2P3 - Paris (France)] (and others)

    2006-05-01

    The SUCIMA collaboration has been developing instruments and methods for real-time, high granularity imaging of extended electron sources. In particular, dosimetry of intravascular brachytherapy {beta} sources has been intensively studied, together with monitoring of hadrontherapy beams by imaging of secondary electrons emitted by a non-disruptive target. The paper reports the latest results on absolute dosimetry with a large-area silicon strip detectors and on beam monitoring with a hybrid pad sensor.

  19. Multi-life-stage monitoring system based on fibre bragg grating sensors for more reliable wind turbine rotor blades: Experimental and numerical analysis of deformation and failure in composite materials

    DEFF Research Database (Denmark)

    Pereira, Gilmar Ferreira

    and structural health monitoring of wind turbine blades. The work presented sets the required framework to develop a monitoring system based on fibre Bragg gratings (FBG), which can be applied to the different life stages of a wind turbine blade. In this concept, the different measured physical parameters...... turbine as long as it is monitored. Thus, a novel crack/damage detection method using FBG sensors is presented, and software/tools are developed for signal simulation and post-processing. The first part of the thesis is an introduction to the multi-life-stage monitoring system based on FBG sensors...... and the damage tolerant design of fibre reinforced materials, where the different theory and numerical models used are presented. The second part of the thesis is a compilation of scientific journal papers, in which the use of FBG sensors to monitor the different life-stages of the wind turbine rotor blade...

  20. Localization of Auricular Projection Area of the Liver and Its Use in the Monitoring of Viral Hepatitis

    Institute of Scientific and Technical Information of China (English)

    Jan Z. Szopinski; Xiao Hong Teng; Georg P. Lochner; Tomasz Macura; Iwona Karcz-Socha; Anna Kasprzyk-Minkner; Krzysztof Kielan; Barbara Krupa-Jezierska; Dariusz J. Nasiek; Piotr Warakomski

    2006-01-01

    Background:Localization of auricular projection area of the liver and evaluation of its usefulness in the monitoring of viral hepatitis. Design, Patients and Setting: Comparative study of the degree of electrical rectification measured at various spots in the auricular concha region, in 19 inpatients with hepatitis B and 15 clinically healthy volunteers, at the Department of Infectious Diseases, Provincial Teaching Hospital,Tychy, Poland. Intervention: Evaluation of electrical rectification at various spots on the auricular concha using a "rectification ratio" that quantifies the degree of rectification (normal range:0-60%). Main outcome measure: The location of the skin area where a statistically significant difference existed between the rectification ratios was observed in patients (82±12% at the time of the 'peak period') versus controls (42±8%). Results: A location was identified on the ear auricle where the electrical rectification phenomenon demonstrated a dependence on the presence of hepatitis. Conclusions: Liver projection area exists on the ear auricle which is located within the region of cymba conchae, next to anthelix and the cavity of concha. The existence of viral hepatitis causes this skin area to show a higher degree of electrical rectification once the skin resistance 'breakthrough effect' has been induced. Evaluation of the rectification phenomenon of the liver projection area provides a method of non-invasive monitoring of viral hepatitis.

  1. Continuing pollution from the Rum Jungle U-Cu project: A critical evaluation of environmental monitoring and rehabilitation

    Energy Technology Data Exchange (ETDEWEB)

    Mudd, Gavin M., E-mail: Gavin.Mudd@eng.monash.edu.a [Environmental Engineering, Dept of Civil Engineering, Monash University, Clayton, VIC 3800 (Australia); Patterson, James [Environmental Engineering Consultant, Sydney, NSW (Australia)

    2010-05-15

    The former Rum Jungle uranium-copper project, Australia, is an internationally important case study on environmental pollution from and rehabilitation of mining. The Rum Jungle mining project is briefly reviewed, followed by a critical evaluation of monitoring data and pollution loads prior to and after rehabilitation - leading to the conclusion that rehabilitation has clearly failed the test of time after just two decades. The most critical findings are the need to understand pollution cycles holistically, and designing monitoring regimes to match, explicit inclusion of radiological criteria (lacking in original planning), and finally the need to set targets based on environmental criteria. Two examples include polluted groundwater which was excluded from rehabilitation and the poor design, construction and/or performance of engineered soil covers - both leading to increasing acid drainage impacts on the Finniss River. The critical review therefore presents a valuable case study of the environmental performance of uranium mine site rehabilitation. - The Rum Jungle U-Cu project underwent extensive rehabilitation in the 1980's, however, it remains a major cause of pollution to the Finniss River.

  2. Analysis of the Problems about Project Cost Management in Present Stage of Engineering Construction Projects%分析现阶段工程建设项目中工程造价管理存在的问题

    Institute of Scientific and Technical Information of China (English)

    高凌

    2011-01-01

    阐述了现阶段工程建设项目中工程造价管理存在的主要问题,为造价管理理论的研究起到抛砖引玉的作用,为项目管理者提供借鉴,使我国的建设项目能够健康发展,更好的为经济建设服务.%This paper explains the main problems about project cost management in present stage of engineering construction projects, which plays a role that offers a few ordinary introductory remarks so that others may offer their valuable ideas in the research of construction cost management theory,helps the project managers, makes our country's construction projects develop healthily and serves the economic construction better.

  3. Identification of growth stage molecular markers in Trichoderma sp. 'atroviride type B' and their potential application in monitoring fungal growth and development in soil.

    Science.gov (United States)

    Mendoza-Mendoza, Artemio; Steyaert, Johanna; Nieto-Jacobo, Maria Fernanda; Holyoake, Andrew; Braithwaite, Mark; Stewart, Alison

    2015-11-01

    Several members of the genus Trichoderma are biocontrol agents of soil-borne fungal plant pathogens. The effectiveness of biocontrol agents depends heavily on how they perform in the complex field environment. Therefore, the ability to monitor and track Trichoderma within the environment is essential to understanding biocontrol efficacy. The objectives of this work were to: (a) identify key genes involved in Trichoderma sp. 'atroviride type B' morphogenesis; (b) develop a robust RNA isolation method from soil; and (c) develop molecular marker assays for characterizing morphogenesis whilst in the soil environment. Four cDNA libraries corresponding to conidia, germination, vegetative growth and conidiogenesis were created, and the genes identified by sequencing. Stage specificity of the different genes was confirmed by either Northern blot or quantitative reverse-transcriptase PCR (qRT-PCR) analysis using RNA from the four stages. con10, a conidial-specific gene, was observed in conidia, as well as one gene also involved in subsequent stages of germination (L-lactate/malate dehydrogenase encoding gene). The germination stage revealed high expression rates of genes involved in amino acid and protein biosynthesis, while in the vegetative-growth stage, genes involved in differentiation, including the mitogen-activated protein kinase kinase similar to Kpp7 from Ustilago maydis and the orthologue to stuA from Aspergillus nidulans, were preferentially expressed. Genes involved in cell-wall synthesis were expressed during conidiogenesis. We standardized total RNA isolation from Trichoderma sp. 'atroviride type B' growing in soil and then examined the expression profiles of selected genes using qRT-PCR. The results suggested that the relative expression patterns were cyclic and not accumulative.

  4. Mid-Columbia - Mapping of Invasive Plants and Monitoring of Efficacy and Impacts in Support of Invasive Control and Rehabilitation Projects 2015

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The proposed project will be to hire and train a volunteer invasives mapping and monitoring crew for two primary purposes. The first will be to locate and map...

  5. Hanford Reach/Columbia - Mapping of Invasive Plants and Monitoring of Efficacy and Impacts in Support of Invasive Control and Rehabilitation Projects

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The proposed project will hire and train an invasives mapping and monitoring crew for two primary purposes. The first will be to locate and map populations of...

  6. Spring Chinook Salmon Interactions Indices and Residual/Precocial Monitoring in the Upper Yakima Basin; Yakima/Klickitat Fisheries Project Monitoring and Evaluation, 2001-2002 Annual Report.

    Energy Technology Data Exchange (ETDEWEB)

    Pearsons, Todd N.; James, Brenda B.; Johnson, Christopher L. (Washington Department of Fish and Wildlife, Olympia, WA)

    2003-05-01

    . 1997). Monitoring ecological interactions will be accomplished using interactions indices. Interactions indices will be used to index the availability of prey and competition for food and space. The tasks described below represent various subject areas of juvenile spring chinook salmon monitoring but are treated together because they can be accomplished using similar methods and are therefore more cost efficient than if treated separately. Three areas of investigation we pursued in this work were: (1) strong interactor monitoring (competition index and prey index), (2) carrying capacity monitoring (microhabitat monitoring); (3) residual and precocial salmon monitoring (abundance). This report is organized into three chapters to represent these three areas of investigation. Data were collected during the summer and fall, 2002 in index sections of the upper Yakima Basin (Figure 1). Hatchery reared spring chinook salmon were first released during the spring of 1999. The monitoring plan for the Yakima/Klickitat Fisheries Project calls for the continued monitoring of the variables covered in this report. All findings in this report should be considered preliminary and subject to further revision as more data and analytical results become available.

  7. Air Sensor Kit Performance Testing and Pollutant Mapping Supports Community Air Monitoring Project

    Science.gov (United States)

    EPA is collaborating on a research project with the South Coast Air Quality Management District in Diamond Bar, Calif. to gain an enhanced understanding of fine particulate matter (PM2.5) and ozone concentrations across the study area.

  8. Self-Repairing Flight Control System for Online Health Monitoring and Recovery Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In this SBIR project, a reliable self-repairing Flight Control System (FCS) will be developed. To achieve this goal, an artificial Neural Network based Sensor...

  9. FINAL PROJECT REPORT: A Geophysical Characterization & Monitoring Strategy for Determining Hydrologic Processes in the Hyporheic Corridor at the Hanford 300-Area

    Energy Technology Data Exchange (ETDEWEB)

    Lee Slater

    2011-08-15

    The primary objective of this research was to advance the prediction of solute transport between the Uranium contaminated Hanford aquifer and the Columbia River at the Hanford 300 Area by improving understanding of how fluctuations in river stage, combined with subsurface heterogeneity, impart spatiotemporal complexity to solute exchange along the Columbia River corridor. Our work explored the use of continuous waterborne electrical imaging (CWEI), in conjunction with fiber-optic distributed temperature sensor (FO-DTS) and time-lapse resistivity monitoring, to improve the conceptual model for how groundwater/surface water exchange regulates uranium transport. We also investigated how resistivity and induced polarization can be used to generate spatially rich estimates of the variation in depth to the Hanford-Ringold (H-R) contact between the river and the 300 Area Integrated Field Research Challenge (IFRC) site. Inversion of the CWEI datasets (a data rich survey containing ~60,000 measurements) provided predictions of the distributions of electrical resistivity and polarizability, from which the spatial complexity of the primary hydrogeologic units along the river corridor was reconstructed. Variation in the depth to the interface between the overlying coarse-grained, high permeability Hanford Formation and the underlying finer-grained, less permeable Ringold Formation, an important contact that limits vertical migration of contaminants, has been resolved along ~3 km of the river corridor centered on the IFRC site in the Hanford 300 Area. Spatial variability in the thickness of the Hanford Formation captured in the CWEI datasets indicates that previous studies based on borehole projections and drive-point and multi-level sampling likely overestimate the contributing area for uranium exchange within the Columbia River at the Hanford 300 Area. Resistivity and induced polarization imaging between the river and the 300 Area IFRC further imaged spatial variability in

  10. 南水北调西线一期工程中的长深引水隧洞%LONG AND DEEP DIVERSION TUNNELS OF 1ST STAGE PROJECT IN WEST ROUTE OF SOUTH-NORTH WATER TRANSFER PROJECT

    Institute of Scientific and Technical Information of China (English)

    沈凤生; 刘新

    2003-01-01

    West Route of South-North Water Transfer Project,situated in southeastern Qinghai-Tibet Plateau,is a giant project,which will deliver 17 billion m3 of water from the main stream and tributaries upstream of the Yangtze River to the upper reaches of the Yellow River. It is to be constructed in 3 stages, of which the 1st stage project includes delivering 4 billion m3 of water by gravity from two tributaries of Yalong River and three tributaries of Dadu River. The project consists of 5 dams,7 tunnels and a channel in series,with the dam height of 63~123 m and water transfer length of 260.3 km,of which the tunnels measure 244.1 km. The special climatic,environmental and geologic conditions make the project much more complicated in construction,especially 3 tunnels with the length longer than 50 km each create challenges to the technical requirements of engineering survey,design and construction.

  11. Mitigation and Monitoring Plan for impacted wetlands at the Gunnison UMTRA Project site, Gunnison, Colorado. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    1994-12-01

    The Gunnison, Colorado, abandoned uranium mill site is one site being cleaned up by the DOE under UMTRCA authority. This site`s contaminated material is being transported to a disposal site on US Bureau of Land Management (BLM) land east of Gunnison. Remedial action activities have temporarily disturbed 0.8 acre (ac) (0.3 hectares [ha]) of wetlands and permanently eliminated 4.3 ac (1.7 ha). As required by the Clean Water Act, the US Army Corps of Engineers (USACE) prepared a Section 404 Permit that addresses the loss of wetlands as a result of remedial action at the Gunnison UMTRA Project site. The 404 permit includes this report as an attachment and it describes the wetland mitigation and monitoring plan. The DOE formulated this plan in consultation with the BLM and the USACE. This report represents a revised version of the mitigation and monitoring plan (DOE, 1992b).

  12. The Multi-Isotope Process (MIP) Monitor Project: FY13 Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Meier, David E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Coble, Jamie B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jordan, David V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Mcdonald, Luther W. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Forrester, Joel B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Schwantes, Jon M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Unlu, Kenan [Pennsylvania State Univ., University Park, PA (United States); Landsberger, Sheldon [Univ. of Texas, Austin, TX (United States); Bender, Sarah [Pennsylvania State Univ., University Park, PA (United States); Dayman, Kenneth J. [Univ. of Texas, Austin, TX (United States); Reilly, Dallas D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2013-09-01

    The Multi-Isotope Process (MIP) Monitor provides an efficient approach to monitoring the process conditions in reprocessing facilities in support of the goal of “… (minimization of) the risks of nuclear proliferation and terrorism.” The MIP Monitor measures the distribution of the radioactive isotopes in product and waste streams of a nuclear reprocessing facility. These isotopes are monitored online by gamma spectrometry and compared, in near-real-time, to spectral patterns representing “normal” process conditions using multivariate analysis and pattern recognition algorithms. The combination of multivariate analysis and gamma spectroscopy allows us to detect small changes in the gamma spectrum, which may indicate changes in process conditions. By targeting multiple gamma-emitting indicator isotopes, the MIP Monitor approach is compatible with the use of small, portable, relatively high-resolution gamma detectors that may be easily deployed throughout an existing facility. The automated multivariate analysis can provide a level of data obscurity, giving a built-in information barrier to protect sensitive or proprietary operational data. Proof-of-concept simulations and experiments have been performed in previous years to demonstrate the validity of this tool in a laboratory setting for systems representing aqueous reprocessing facilities. However, pyroprocessing is emerging as an alternative to aqueous reprocessing techniques.

  13. Post transplant lymphoproliferative disease in pediatric solid organ transplant patients: A possible role for [{sup 18}F]-FDG-PET(/CT) in initial staging and therapy monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Falck, C. von [Department of Diagnostic Radiology, Medizinische Hochschule Hannover (Medical School Hanover), Carl-Neuberg-Strasse 1, 30625 Hannover (Germany)], E-mail: Falck.Christian.von@mh-hannover.de; Maecker, B. [Department of Pediatric Hematology and Oncology, Medizinische Hochschule Hannover (Medical School Hanover), Carl-Neuberg-Strasse 1, 30625 Hannover (Germany); Schirg, E. [Department of Diagnostic Radiology, Medizinische Hochschule Hannover (Medical School Hanover), Carl-Neuberg-Strasse 1, 30625 Hannover (Germany); Boerner, A.R.; Knapp, W.H. [Department of Nuclear Medicine, Medizinische Hochschule Hannover (Medical School Hanover), Carl-Neuberg-Strasse 1, 30625 Hannover (Germany); Klein, C. [Department of Pediatric Hematology and Oncology, Medizinische Hochschule Hannover (Medical School Hanover), Carl-Neuberg-Strasse 1, 30625 Hannover (Germany); Galanski, M. [Department of Diagnostic Radiology, Medizinische Hochschule Hannover (Medical School Hanover), Carl-Neuberg-Strasse 1, 30625 Hannover (Germany)

    2007-09-15

    Post transplant lymphoproliferative disease (PTLD) is a severe complication after solid organ or bone marrow transplantation. In pediatric transplant recipients PTLD is the most common malignancy. The aim of this study was to evaluate a possible role for positron emission tomography with [{sup 18}F]-2-fluoro-2-desoxy-glucose (FDG) in the initial staging and in therapy monitoring of pediatric patients suffering from biopsy-proven CD20-positive PTLD after solid organ transplantation. Seven pediatric patients were included. All available imaging studies - CT (n = 15), MRI (n = 16) and PET/PETCT (n = 16) - were reviewed on a lesion by lesion base. The performance of FDG-PET in the initial staging and during therapy with a chimeric anti-CD20 antibody was compared to conventional cross sectional imaging and correlated with the clinical outcome. FDG-PET identified all sites of disease as shown by CT/MRI and helped to clarify the significance of equivocal findings. The initial stage of disease was correctly identified by FDG-PET alone when compared to CT/MRI. During therapy, FDG-PET was superior to conventional cross-sectional imaging in the early evaluation of response.

  14. Resource conservation and recovery act ground-water monitoring projects for Hanford facilities: Progress report, January 1--March 31, 1989

    Energy Technology Data Exchange (ETDEWEB)

    Smith, R.M.; Bates, D.J.; Lundgren, R.E.

    1989-06-01

    This document describes the progress of 13 Hanford Site ground-water monitoring projects for the period January 1 to March 31, 1989. The work described in this document is conducted by the Pacific Northwest Laboratory under the management of Westinghouse Hanford Company for the US Department of Energy. Concentrations of ground-water constituents are compared to federal drinking water standards throughout this document for reference purposes. All drinking water supplied from the sampled aquifer meets regulatory standards for drinking water quality. 32 refs., 30 figs., 103 tabs.

  15. IAEA coordinated research project on nuclear data for charged-particle monitor reactions and medical isotope production

    Science.gov (United States)

    Capote, Roberto; Nichols, Alan L.; Nortier, Francois Meiring; Carlson, Brett V.; Engle, Jonathan W.; Hermanne, Alex; Hussain, Mazhar; Ignatyuk, Anatoly V.; Kellett, Mark A.; Kibédi, Tibor; Kim, Guinyun; Kondev, Filip G.; Lebeda, Ondrej; Luca, Aurelian; Naik, Haladhara; Nagai, Yasuki; Spahn, Ingo; Suryanarayana, Saraswatula V.; Tárkányi, Ferenc T.; Verpelli, Marco

    2017-09-01

    An IAEA coordinated research project was launched in December 2012 to establish and improve the nuclear data required to characterise charged-particle monitor reactions and extend data for medical radionuclide production. An international team was assembled to undertake work addressing the requirements for more accurate cross-section data over a wide range of targets and projectiles, undertaken in conjunction with a limited number of measurements and more extensive evaluations of the decay data of specific radionuclides. These studies are nearing completion, and are briefly described below.

  16. Energy Efficiency in Norway 1996-1999. Monitoring tools for energy efficiency in Europe: the ODYSSEE and MURE projects

    Energy Technology Data Exchange (ETDEWEB)

    Rosenberg, Eva

    2002-05-01

    This is the national report for Norway in the EU/SAVE project ''Monitoring tools for energy efficiency in Europe: the ODYSSEE and MURE projects''. The report deals with energy use and energy efficiency in Norway 1990-1999. Final energy use per Gross Domestic Product (GDP) was reduced by approximately 1.6% per year from 1990 to 1999. The energy efficiency improvement has been calculated to 0.4% pr year, while the role of structural changes has been 1.2% pr year. A detailed sector analysis has been done, applying Laspeyres indices to attribute changes in energy use to activity, structure or intensity (efficiency). Aggregating sectors, we have found a total efficiency improvement of approximately 8 TWh from 1990 to 1999. (author)

  17. Compliance Monitoring of Underwater Blasting for Rock Removal at Warrior Point, Columbia River Channel Improvement Project, 2009/2010

    Energy Technology Data Exchange (ETDEWEB)

    Carlson, Thomas J.; Johnson, Gary E.; Woodley, Christa M.; Skalski, J. R.; Seaburg, Adam

    2011-05-10

    The U.S. Army Corps of Engineers, Portland District (USACE) conducted the 20-year Columbia River Channel Improvement Project (CRCIP) to deepen the navigation channel between Portland, Oregon, and the Pacific Ocean to allow transit of fully loaded Panamax ships (100 ft wide, 600 to 700 ft long, and draft 45 to 50 ft). In the vicinity of Warrior Point, between river miles (RM) 87 and 88 near St. Helens, Oregon, the USACE conducted underwater blasting and dredging to remove 300,000 yd3 of a basalt rock formation to reach a depth of 44 ft in the Columbia River navigation channel. The purpose of this report is to document methods and results of the compliance monitoring study for the blasting project at Warrior Point in the Columbia River.

  18. Environmental monitoring for the DOE coolside and LIMB demonstration extension projects. Final report, May--August 1991

    Energy Technology Data Exchange (ETDEWEB)

    White, T.; Contos, L.; Adams, L. [Radian Corp., Research Triangle Park, NC (United States)

    1992-03-01

    The purpose of this document is to present environmental monitoring data collected during the US Department of Energy Limestone Injection Multistage Burner (DOE LIMB) Demonstration Project Extension at the Ohio Edison Edgewater Generating Station in Lorain, Ohio. The DOE project is an extension of the US Environmental Protection Agency`s (EPA`s) original LIMB Demonstration. The program is operated nuclear DOE`s Clean Coal Technology Program of ``emerging clean coal technologies`` under the categories of ``in boiler control of oxides of sulfur and nitrogen`` as well as ``post-combustion clean-up.`` The objective of the LIMB program is to demonstrate the sulfur dioxide (SO{sub 2}) and nitrogen oxide (NO{sub x}) emission reduction capabilities of the LIMB system. The LIMB system is a retrofit technology to be used for existing coal-fired boilers equipped with electrostatic precipitators (ESPs).

  19. Framework for monitoring the social and economic impacts associated with the construction of the Skagit Nuclear Project in Skagit County, Washington

    Energy Technology Data Exchange (ETDEWEB)

    Merwin, D.J.; Greene, M.

    1977-09-30

    The paper discusses an information system which has been developed to monitor the social and economic impacts associated with the construction of twin nuclear reactors in Skagit County, Washington, by Puget Sound Power and Light Company. The monitoring system has been specifically designed to track the social and economic impacts of the Skagit Nuclear Project as they occur.

  20. Structural health monitoring of wind turbine blades : SE 265 Final Project.

    Energy Technology Data Exchange (ETDEWEB)

    Barkley, W. C.(Walter C.); Jacobs, Laura D.; Rutherford, A. C.(Amanda C.); Puckett, Anthony

    2006-03-23

    ACME Wind Turbine Corporation has contacted our dynamic analysis firm regarding structural health monitoring of their wind turbine blades. ACME has had several failures in previous years. Examples are shown in Figure 1. These failures have resulted in economic loss for the company due to down time of the turbines (lost revenue) and repair costs. Blade failures can occur in several modes, which may depend on the type of construction and load history. Cracking and delamination are some typical modes of blade failure. ACME warranties its turbines and wishes to decrease the number of blade failures they have to repair and replace. The company wishes to implement a real time structural health monitoring system in order to better understand when blade replacement is necessary. Because of warranty costs incurred to date, ACME is interested in either changing the warranty period for the blades in question or predicting imminent failure before it occurs. ACME's current practice is to increase the number of physical inspections when blades are approaching the end of their fatigue lives. Implementation of an in situ monitoring system would eliminate or greatly reduce the need for such physical inspections. Another benefit of such a monitoring system is that the life of any given component could be extended since real conditions would be monitored. The SHM system designed for ACME must be able to operate while the wind turbine is in service. This means that wireless communication options will likely be implemented. Because blade failures occur due to cyclic stresses in the blade material, the sensing system will focus on monitoring strain at various points.

  1. Yakima/Klickitat Fisheries Project Genetic Studies; Yakima/Klickitat Fisheries Project Monitoring and Evaluation, 2001-2002 Annual Report.

    Energy Technology Data Exchange (ETDEWEB)

    Busack, Craig A.; Fritts, Anthony L.; Loxterman, Janet (Washington Department of Fish and Wildlife, Olympia, WA)

    2003-05-01

    current plan of using the Naches population as a wild control, and maintaining a hatchery-only control line alongside the supplemented line. During discussions this year a major issue was the possible impact to the research and to the supplementation effort, of gene flow from precocious males from the hatchery control line into the supplemented line. At the end of the contracting period, this issue still had not been resolved. Along with the discussion of development of the domestication research design, chapter 4 presents the current monitoring plan document, with discussion of the approach to the various traits to be analyzed. Chapters 5 and 6 deal with experimental power of the domestication monitoring design. There is still much work to be done on power, but in chapter 5 we explore our power to detect differences among the three lines for traits measured on individual adults. Power was found to be quite good for effects of 5% per generation over three generations for traits having a coefficient of variation (CV) of 10-20%, but low if the CV was 50%. Power is higher for comparisons between the hatchery control line and supplemented line than between the supplemented line and the wild control, a consequence of trying to avoid heavy impacts to the Naches population. Power could be improved considerably improved by sampling more Naches fish in years of high abundance. Chapter 6 presents the same power analysis, but attempts to explore the effect of precocious males from the hatchery control line spawning in the wild. It is clear that if gene flow from precocious males is more than one or two percent that the between line comparisons will be biased, making the supplemented line appear to be more similar to the hatchery control line than it should and more different from the wild control line than it should. However, it was also clear that more analysis is desirable, as the heightened or diminished power is really just an enhancement or reduction of a real difference. A

  2. Yakima/Klickitat Fisheries Project Genetic Studies; Yakima/Klickitat Fisheries Project Monitoring and Evaluation, 2001-2002 Annual Report.

    Energy Technology Data Exchange (ETDEWEB)

    Busack, Craig A.; Fritts, Anthony L.; Loxterman, Janet (Washington Department of Fish and Wildlife, Olympia, WA)

    2003-05-01

    current plan of using the Naches population as a wild control, and maintaining a hatchery-only control line alongside the supplemented line. During discussions this year a major issue was the possible impact to the research and to the supplementation effort, of gene flow from precocious males from the hatchery control line into the supplemented line. At the end of the contracting period, this issue still had not been resolved. Along with the discussion of development of the domestication research design, chapter 4 presents the current monitoring plan document, with discussion of the approach to the various traits to be analyzed. Chapters 5 and 6 deal with experimental power of the domestication monitoring design. There is still much work to be done on power, but in chapter 5 we explore our power to detect differences among the three lines for traits measured on individual adults. Power was found to be quite good for effects of 5% per generation over three generations for traits having a coefficient of variation (CV) of 10-20%, but low if the CV was 50%. Power is higher for comparisons between the hatchery control line and supplemented line than between the supplemented line and the wild control, a consequence of trying to avoid heavy impacts to the Naches population. Power could be improved considerably improved by sampling more Naches fish in years of high abundance. Chapter 6 presents the same power analysis, but attempts to explore the effect of precocious males from the hatchery control line spawning in the wild. It is clear that if gene flow from precocious males is more than one or two percent that the between line comparisons will be biased, making the supplemented line appear to be more similar to the hatchery control line than it should and more different from the wild control line than it should. However, it was also clear that more analysis is desirable, as the heightened or diminished power is really just an enhancement or reduction of a real difference. A

  3. Inducing a CO2 leak into a shallow aquifer (CO2FieldLab EUROGIA+ project): Monitoring the CO2 plume in groundwaters

    OpenAIRE

    Gal, Frédérick; Proust, Eric; Humez, Pauline; Braibant, Gilles; Brach, Michel; Koch, Florian; Widory, David; Girard, Jean-François

    2012-01-01

    International audience; An important part of the CO2 capture and storage projects concerns monitoring methods. Here we are focusing on the geochemical monitoring methods that may be deployed at depth to ensure early warning in case of unwanted CO2 leakages from a storage site. Independently from the nature of the reservoir (saline aquifer, depleted oil/gas reservoir), aquifers are ubiquitous in the overlying sedimentary pile. Before deploying water monitoring methods at depth, where long-term...

  4. Instrumentation and monitoring of the nextgen road infrastructure: Some results and perspectives from the R5G project

    Science.gov (United States)

    Hautière, Nicolas; Bourquin, Frédéric

    2017-04-01

    Through the centuries, the roads - which today constitute in France a huge transport network of 1 millions kilometers length - have always been able to cope with society needs and challenges. As a consequence, the next generation road infrastructure will have to take into account at least three societal transitions: ecological, energetic and digital. The goal of the 5th generation road project (R5G©) [1], led by Ifsttar in France, aligned with the Forever Open program [2], is to design and build demonstrators of such future road infrastructures. The goal of this presentation is to present different results related to the greening of road materials [3], the design of energy-positive roads [4, 5], the test of roads that self-diagnose [6], the design of roads adapted for connected [7], autonomous [8] and electrified vehicles [9], etc. In terms of perspectives, we will demonstrate that the road infrastructures will soon become a complex system: On one side road users will benefit from new services, on the other side such massively connected and instrumented infrastructures will potentially become an opportune sensor for knowledge development in geoscience, such as air quality, visibility and fog monitoring. References: [1] R5G project. r5g.ifsttar.fr [2] Forever Open Road project. www.foreveropenroad.eu [3] Biorepavation project. www.infravation.net/projects/BIOREPAVATION [4] N. Le Touz, J. Dumoulin. Numerical study of the thermal behavior of a new deicing road structure design with energy harvesting capabilities. EGU General Assembly 2015, Apr 2015, Vienne, Austria. [5] S. Asfour, F. Bernardin, E. Toussaint, J.-M. Piau. Hydrothermal modeling of porous pavement for its surface de-freezing. Applied Thermal Engineering. Volume 107, 25 August 2016, Pages 493-500 [6] LGV BPL Instrumentation. http://railenium.eu/wp-content/uploads/2016/08/INSTRUMENTATION-BPL-FR.pdf [7] SCOOP@F project. https://ec.europa.eu/inea/en/connecting-europe-facility/cef-transport/projects

  5. The PARAChute Project: Remote Monitoring of Posture and Gait for Fall Prevention

    Directory of Open Access Journals (Sweden)

    Charpillet François

    2007-01-01

    Full Text Available Falls in the elderly are a major public health problem due to both their frequency and their medical and social consequences. In France alone, more than two million people aged over 65 years old fall each year, leading to more than 9 000 deaths, in particular in those over 75 years old (more than 8 000 deaths. This paper describes the PARAChute project, which aims to develop a methodology that will enable the detection of an increased risk of falling in community-dwelling elderly. The methods used for a remote noninvasive assessment for static and dynamic balance assessments and gait analysis are described. The final result of the project has been the development of an algorithm for movement detection during gait and a balance signature extracted from a force plate. A multicentre longitudinal evaluation of balance has commenced in order to validate the methodologies and technologies developed in the project.

  6. Results from the Big Spring basin water quality monitoring and demonstration projects, Iowa, USA

    Science.gov (United States)

    Rowden, R.D.; Liu, H.; Libra, R.D.

    2001-01-01

    Agricultural practices, hydrology, and water quality of the 267-km2 Big Spring groundwater drainage basin in Clayton County, Iowa, have been monitored since 1981. Land use is agricultural; nitrate-nitrogen (-N) and herbicides are the resulting contaminants in groundwater and surface water. Ordovician Galena Group carbonate rocks comprise the main aquifer in the basin. Recharge to this karstic aquifer is by infiltration, augmented by sinkhole-captured runoff. Groundwater is discharged at Big Spring, where quantity and quality of the discharge are monitored. Monitoring has shown a threefold increase in groundwater nitrate-N concentrations from the 1960s to the early 1980s. The nitrate-N discharged from the basin typically is equivalent to over one-third of the nitrogen fertilizer applied, with larger losses during wetter years. Atrazine is present in groundwater all year; however, contaminant concentrations in the groundwater respond directly to recharge events, and unique chemical signatures of infiltration versus runoff recharge are detectable in the discharge from Big Spring. Education and demonstration efforts have reduced nitrogen fertilizer application rates by one-third since 1981. Relating declines in nitrate and pesticide concentrations to inputs of nitrogen fertilizer and pesticides at Big Spring is problematic. Annual recharge has varied five-fold during monitoring, overshadowing any water-quality improvements resulting from incrementally decreased inputs. ?? Springer-Verlag 2001.

  7. Perinatal health monitoring in europe: Results from the EURO-PERISTAT project

    NARCIS (Netherlands)

    Gissler, M.; Mohangoo, A.D.; Blondel, B.; Chalmers, J.; MacFarlane, A.; Gaizauskiene, A.; Gatt, M.; Lack, N.; Sakkeus, L.; Zeitlin, J.

    2010-01-01

    Data about deliveries, births, mothers and newborn babies are collected extensively to monitor the health and care of mothers and babies during pregnancy, delivery and the post-partum period, but there is no common approach in Europe. We analysed the problems related to using the European data for i

  8. Monitoring Staff Performance: A Plan for Quality Control in Project Follow Through.

    Science.gov (United States)

    Jackson, Donald A.; Bushell, Don, Jr.

    This report describes a staff training and performance monitoring system for elementary school teachers, teacher aides, and parent aides participating in the Behavior Analysis Follow Through (B.A.) compensatory education program. The B.A. model involves the use of additional staff, individualized instruction, programmed curriculum materials, and a…

  9. Community Air Sensor Network (CAIRSENSE) Project: Lower Cost, Continuous Ambient Monitoring Methods

    Science.gov (United States)

    Advances in air pollution sensor technology have enabled the development of small and low cost systems to measure outdoor air pollution. The deployment of numerous sensors across a small geographic area would have potential benefits to supplement existing monitoring networks and ...

  10. Perinatal health monitoring in europe: Results from the EURO-PERISTAT project

    NARCIS (Netherlands)

    Gissler, M.; Mohangoo, A.D.; Blondel, B.; Chalmers, J.; MacFarlane, A.; Gaizauskiene, A.; Gatt, M.; Lack, N.; Sakkeus, L.; Zeitlin, J.

    2010-01-01

    Data about deliveries, births, mothers and newborn babies are collected extensively to monitor the health and care of mothers and babies during pregnancy, delivery and the post-partum period, but there is no common approach in Europe. We analysed the problems related to using the European data for i

  11. Fish Research Project Oregon; Umatilla Hatchery Monitoring and Evaluation, 1994-1995 Annual Report.

    Energy Technology Data Exchange (ETDEWEB)

    Hayes, Michael C.; Waln, Karen; Carmichael, Richard W. (Oregon Department of Fish and Wildlife, Portland, OR)

    1996-01-01

    The Northwest Power Planning Council`s Columbia River Basin Fish and Wildlife Program authorized construction of the Umatilla Hatchery in 1986. Measure 703 of the program amended the original authorization for the hatchery and specified evaluation of the Michigan type of rearing using oxygen supplementation to reach production goals of 290,000 lb of chinook salmon (Oncorhynchus tshawytscha) and steelhead (Oncorhynchus nzykiss). The hatchery was completed in the fall of 1991. Partial justification for the hatchery was to develop considerable knowledge and understanding of new production and supplementation techniques. The use of the Michigan raceways in rearing at Umatilla Hatchery was selected because it could increase smolt production given the limited hatchery well water supply and allow comparison of Michigan raceways with the standard Oregon raceways. Results of testing the Michigan raceways will have systematic application in the Columbia Basin. The Umatilla Hatchery is the foundation for rehabilitating chinook salmon and enhancing steelhead in the Umatilla River and is expected to contribute significantly to the Northwest Power Planning Council`s goal of doubling salmon production in the Columbia Basin. Hatchery production goals and a comprehensive monitoring and evaluation plan were presented in the Umatilla Hatchery Master Plan . The Comprehensive Plan for Monitoring and Evaluation of Umatilla Hatchery was approved by the Northwest Power Planning Council as a critical adaptive management guide for fisheries rehabilitation in the Umatilla River. Monitoring and evaluation will be used to increase knowledge about uncertainties inherent in the fisheries rehabilitation and will complement the developing systematic monitoring and evaluation program. This report covers the first four years of the monitoring of the hatchery.

  12. Construction project bidding stage cost control research%建筑工程招投标阶段造价控制研究

    Institute of Scientific and Technical Information of China (English)

    王赟

    2016-01-01

    With the improvement of socialist market economy system,the construction projects have gradually realized the market economy,and construction projects has increased the project cost control becomes more and more important.The current cost control for construction projects still in the construction process and the settlement process,ignoring the cost control in the bidding stage.Based on this,the in the construction project bidding and cost control on the basis of on,analysis of the impact of bidding cost control of the main reasons and the bidding tendering cost control problems,and on the basis of bidding for the tender stage cost control effective measures are discussed.%随着社会主义市场经济体系的不断完善,建筑项目也逐渐的实现了市场经济化,而建设项目的不断增多使得工程项目的造价控制显得愈发重要。当前对于建筑工程的造价控制仍旧以施工过程和结算过程为主,忽视了招投标阶段的造价控制。基于此,文章在对建筑工程招投标以及造价控制阐述的基础上,分析了影响招投标造价控制的主要原因以及当前招投标造价控制存在的问题,并在此基础上对招投标阶段造价控制的有效措施进行了探讨。

  13. Field Assessment of the Village Green Project: An Autonomous Community Air Quality Monitoring System

    Science.gov (United States)

    Recent findings on air pollution levels in communities motivate new technologies to assess air pollution at finer spatial scale. The Village Green Project (VGP) is a novel approach using commercially-available technology for long-term community environments air pollution measure...

  14. A Service-Learning Project in Chemistry: Environmental Monitoring of a Nature Preserve

    Science.gov (United States)

    Kammler, David C.; Truong, Triet M.; VanNess, Garrett; McGowin, Audrey E.

    2012-01-01

    A collaborative environmental service-learning project was implemented between upper-level undergraduate science majors and graduate chemistry students at a large state school and first-year students at a small private liberal arts college. Students analyzed the water quality in a nature preserve by determining the quantities of 12 trace metals,…

  15. A Service-Learning Project in Chemistry: Environmental Monitoring of a Nature Preserve

    Science.gov (United States)

    Kammler, David C.; Truong, Triet M.; VanNess, Garrett; McGowin, Audrey E.

    2012-01-01

    A collaborative environmental service-learning project was implemented between upper-level undergraduate science majors and graduate chemistry students at a large state school and first-year students at a small private liberal arts college. Students analyzed the water quality in a nature preserve by determining the quantities of 12 trace metals,…

  16. CitySpace Air Sensor Network Project Conducted to Test New Monitoring Capabilities

    Science.gov (United States)

    The CitySpace project is a new research effort by EPA to field test new, lower-cost air pollution sensors in a mid-sized city to understand how this emerging technology can add valuable information on air pollution patterns in neighboorhoods.

  17. National and Regional Scale Rice Crop Monitoring in Asia with the RIICE and PRISM Projects: From Research to Operation

    Science.gov (United States)

    Nelson, A.; Quicho, E. D.; Maunahan, A. A.; Setiyono, T. D.; Raviz, J. V.; Rala, A. B.; Laborte, A. G.; Holecz, F.; Collivignarelli, F.; Gatti, L.; Barbieri, M.; Mabalay, M. R. O.; De Dios, J. L.; Quilang, E. J. P.

    2015-12-01

    In recent years, remote sensing based mapping and monitoring of the rice crop have been demonstrated in many pilot studies and research sites - mainly in Asia - using both optical and SAR sensors and ground based observations. These efforts have been partly driven by the high demand for more timely, more detailed and more accurate information on the rice crop for applications in both public and private sector, such as food security policy, crop and land management, infrastructure investment and crop insurance. The basic premise being that better access to better information leads to eventual benefits for both producers and consumers through better investment and management at all levels. To realise these benefits means scaling up this work to national and regional levels. This presentation summarises the progress of two related projects in Asia: RIICE (Remote Sensing-based Information and Insurance in emerging Economies) and PRISM (Philippine Rice Information SysteM) that are making the transition from research to operation with the support of national governments and international donors. The presentation focuses on the technology, the partnerships, the achievements and the challenges in embedding both the capacity and the technology for remote sensing based monitoring of rice in countries in South and South East Asia. We highlight several aspects which are essential for a successful transition to a sustainable operational status and lessons learned in each country where the two projects have been operating.

  18. The Yosemite Extreme Panoramic Imaging Project: Monitoring Rockfall in Yosemite Valley with High-Resolution, Three-Dimensional Imagery

    Science.gov (United States)

    Stock, G. M.; Hansen, E.; Downing, G.

    2008-12-01

    Yosemite Valley experiences numerous rockfalls each year, with over 600 rockfall events documented since 1850. However, monitoring rockfall activity has proved challenging without high-resolution "basemap" imagery of the Valley walls. The Yosemite Extreme Panoramic Imaging Project, a partnership between the National Park Service and xRez Studio, has created an unprecedented image of Yosemite Valley's walls by utilizing gigapixel panoramic photography, LiDAR-based digital terrain modeling, and three-dimensional computer rendering. Photographic capture was accomplished by 20 separate teams shooting from key overlapping locations throughout Yosemite Valley. The shots were taken simultaneously in order to ensure uniform lighting, with each team taking over 500 overlapping shots from each vantage point. Each team's shots were then assembled into 20 gigapixel panoramas. In addition, all 20 gigapixel panoramas were projected onto a 1 meter resolution digital terrain model in three-dimensional rendering software, unifying Yosemite Valley's walls into a vertical orthographic view. The resulting image reveals the geologic complexity of Yosemite Valley in high resolution and represents one of the world's largest photographic captures of a single area. Several rockfalls have already occurred since image capture, and repeat photography of these areas clearly delineates rockfall source areas and failure dynamics. Thus, the imagery has already proven to be a valuable tool for monitoring and understanding rockfall in Yosemite Valley. It also sets a new benchmark for the quality of information a photographic image, enabled with powerful new imaging technology, can provide for the earth sciences.

  19. Minimization of dioxins in thermal and industrial processes: mechanisms, monitoring and abatement (minidip): main achievements of this EU-project

    Energy Technology Data Exchange (ETDEWEB)

    Buekens, A.; Segers, P.; Schroyens, K.; Zyaykina, N.

    2002-07-01

    The Minidip Project was prepared with the aim to develop and test a scientifically founded and technically feasible methodology to characterise the relevant major steps of formation, destruction and removal of dioxins in a variety of thermal and metallurgical processes, as a means for optimising primary and secondary measures. The latter were to be proposed after a study of relevant mechanisms in-plant monitoring and abatement measures. For this purpose both major pathways, the precursor and de novo route were to experimentally tested at a lab scale, under conditions typical for those found in industry. Since this approach was novel, it had to be calibrated against actual plant data and experience. In parallel to the lab-scale tests, the formation of dioxins was to be investigated at an industrial scale, in close collaboration with industrial enterprise and featuring innovative methods of monitoring. Major problems in dioxin research have been the minute concentrations of dioxins and the large number of possible factors influencing them. In industrial plant those factors can be varied neither in a wide range, nor independently of other variables. Moreover, memory effects and production priorities preclude a systematic in-plant testing, which was a major justification for the Minidip project. The latter proceeded methodically, by selecting suitable samples to be tested, individually identifying the precise influence of each important variable or other factor, and testing the resulting laboratory findings at a pilot or plant scale. (Author) 4 refs.

  20. AUDIT OF INNOVATIVE IDEAS AS THE PREVIOUS STAGE OF THE BUSINESS-PLAN OF START-UP PROJECTS

    Directory of Open Access Journals (Sweden)

    O. Zhylinska

    2014-09-01

    Full Text Available The phenomenon of feasibility reasoning of venture capital investment for the implementation of innovative ideas is revealed. The main elements of the methodology for feasibility of start-up projects, based on the concept of combination of life cycle of the market, product innovation and startup companies, are characterized. The comparative analysis of methods feasibility study and business plan start-up project is made, the importance of innovative ideas audit in future economic information generation and investment decisions of informal venture capital investors are shown.

  1. Enhanced sensitivity for selected reaction monitoring mass spectrometry-based targeted proteomics using a dual stage electrodynamic ion funnel interface.

    Science.gov (United States)

    Hossain, Mahmud; Kaleta, David T; Robinson, Errol W; Liu, Tao; Zhao, Rui; Page, Jason S; Kelly, Ryan T; Moore, Ronald J; Tang, Keqi; Camp, David G; Qian, Wei-Jun; Smith, Richard D

    2011-02-01

    Selected reaction monitoring mass spectrometry (SRM-MS) is playing an increasing role in quantitative proteomics and biomarker discovery studies as a method for high throughput candidate quantification and verification. Although SRM-MS offers advantages in sensitivity and quantification compared with other MS-based techniques, current SRM technologies are still challenged by detection and quantification of low abundance proteins (e.g. present at ∼10 ng/ml or lower levels in blood plasma). Here we report enhanced detection sensitivity and reproducibility for SRM-based targeted proteomics by coupling a nanospray ionization multicapillary inlet/dual electrodynamic ion funnel interface to a commercial triple quadrupole mass spectrometer. Because of the increased efficiency in ion transmission, significant enhancements in overall signal intensities and improved limits of detection were observed with the new interface compared with the original interface for SRM measurements of tryptic peptides from proteins spiked into non-depleted mouse plasma over a range of concentrations. Overall, average SRM peak intensities were increased by ∼70-fold. The average level of detection for peptides also improved by ∼10-fold with notably improved reproducibility of peptide measurements as indicated by the reduced coefficients of variance. The ability to detect proteins ranging from 40 to 80 ng/ml within mouse plasma was demonstrated for all spiked proteins without the application of front-end immunoaffinity depletion and fractionation. This significant improvement in detection sensitivity for low abundance proteins in complex matrices is expected to enhance a broad range of SRM-MS applications including targeted protein and metabolite validation.

  2. The AAL project: Automated monitoring and intelligent AnaLysis for the ATLAS data taking infrastructure

    CERN Document Server

    Magnoni, L; The ATLAS collaboration; Kazarov, A

    2011-01-01

    The Trigger and Data Acquisition (TDAQ) system of the ATLAS experiment at CERN is the infrastructure responsible for filtering and transferring ATLAS experimental data from detectors to the mass storage system. It relies on a large, distributed computing environment, including thousands of computing nodes with thousands of application running concurrently. In such a complex environment, information analysis is fundamental for controlling applications behavior, error reporting and operational monitoring. During data taking runs, streams of messages sent by applications via the message reporting system together with data published from applications via information services are the main sources of knowledge about correctness of running operations. The huge flow of data produced (with an average rate of O(1-10KHz)) is constantly monitored by experts to detect problem or misbehavior. This require strong competence and experience in understanding and discovering problems and root causes, and often the meaningful in...

  3. The AAL project: automated monitoring and intelligent analysis for the ATLAS data taking infrastructure

    CERN Document Server

    Kazarov, A; The ATLAS collaboration; Magnoni, L

    2011-01-01

    The Trigger and Data Acquisition (TDAQ) system of the ATLAS experiment at CERN is the infrastructure responsible for filtering and transferring ATLAS experimental data from detectors to the mass storage system. It relies on a large, distributed computing environment, including thousands of computing nodes with thousands of application running concurrently. In such a complex environment, information analysis is fundamental for controlling applications behavior, error reporting and operational monitoring. During data taking runs, streams of messages sent by applications via the message reporting system together with data published from applications via information services are the main sources of knowledge about correctness of running operations. The huge flow of data produced (with an average rate of O(1-10KHz)) is constantly monitored by experts to detect problem or misbehavior. This require strong competence and experience in understanding and discovering problems and root causes, and often the meaningful in...

  4. Implementing Avian Inventory and Monitoring Efforts on Corps of Engineers Project Lands

    Science.gov (United States)

    2007-06-01

    surveys are conducted by Steve Calver (CESAS- PD-E) at the Savannah River Site, which is a large dredged-material disposal site in South Carolina. This...Goals and strategies for estimating trends in landbird abundance. Journal of Wildlife Management 68:611-626. Bart, J., B. Andres, S. Brown, G ...Donaldson, B. Harrington, V. Johnston, S. Jones, G . Morrison, and S. Skagen. 2005. The program for regional and international shorebird monitoring (PRISM

  5. 2015 Long-Term Hydrologic Monitoring Program Sampling and Analysis Results Report for Project Rulison, Co

    Energy Technology Data Exchange (ETDEWEB)

    Findlay, Rick [Navarro Research and Engineering, Oak Ridge, TN (United States); Kautsky, Mark [US Department of Energy, Washington, DC (United States). Office of Legacy Management

    2015-12-01

    The U.S. Department of Energy (DOE) Office of Legacy Management conducted annual sampling at the Rulison, Colorado, Site for the Long-Term Hydrologic Monitoring Program (LTHMP) on May 20–22 and 27, 2015. Several of the land owners were not available to allow access to their respective properties, which created the need for several sample collection trips. This report documents the analytical results of the Rulison monitoring event and includes the trip report and the data validation package (Appendix A). The groundwater and surface water monitoring were shipped to the GEL Group Inc. laboratories for analysis. All requested analyses were successfully completed. Samples were analyzed for gamma-emitting radionuclides by high- resolution gamma spectrometry. Tritium was analyzed using two methods, the conventional tritium method, which has a detection limit on the order of 400 picocuries per liter (pCi/L), and the enriched method (for selected samples), which has a detection limit on the order of 3 pCi/L.

  6. Monitoring and evaluation to support adaptive co-management: Lessons learned from the Millennium Villages Project.

    Science.gov (United States)

    Chapman, Sarah; Sullivan, Clare; Palm, Cheryl; Huynh, Uyen; Diru, William; Masira, Jessica

    2016-12-01

    This article focuses attention on monitoring and evaluation approaches that will help resource managers to manage for change and uncertainty in adaptive co-management (ACM). ACM is a learning-by-doing approach that aims to build flexible community-based natural resource governance systems through collaborative or otherwise participatory means. We describe the framework for monitoring and evaluation that we developed and applied in ten African countries, which includes fixed indicators and measures for co-management performance monitoring, a process evaluation element, a platform for repeat ecological surveillance, and a longitudinal household survey. We comment on the usefulness of this framework, and its applicability to a wide range of geographic contexts. We then present a four step model to assist managers in applying the framework to specific co-management problems. The model suggests a cascade approach to defining key evaluations questions at a systems, network, individual and synthesis level. We illustrate the application of our model and framework by means of a case study of a co-managed agroforestry program in western Kenya. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. The Northwest Geysers EGS Demonstration Project Phase 1: Pre-stimulation coupled geomechanical modeling to guide stimulation and monitoring plans

    Energy Technology Data Exchange (ETDEWEB)

    Rutqvist, J.; Dobson, P.F.; Oldenburg, C.M.; Garcia, J.; Walters, M.

    2010-10-20

    This paper presents activities and results associated with Phase 1 (pre-stimulation phase) of an Enhanced Geothermal System (EGS) demonstration project at the northwest part of The Geysers geothermal field, California. The paper presents development of a 3-D geological model, coupled thermal-hydraulic-mechanical (THM) modeling of proposed stimulation injection as well as current plans for stimulation and monitoring of the site. The project aims at creating an EGS by directly and systematically injecting cool water at relatively low pressure into a known High Temperature (about 280 to 350 C) Zone (HTZ) located under the conventional (240 C) steam reservoir at depths of {approx}3 km. Accurate micro-earthquake monitoring initiated before the start of the injection will be used as a tool for tracking the development of the EGS and monitoring changes in microseismicity. We first analyzed historic injection and micro-earthquake data from an injection well (Aidlin 11) located about 3 miles to the west of the new EGS demonstration area. Thereafter, we used the same modeling approach to predict the likely extent of the zone of enhanced permeability for a proposed initial injection in two wells (Prati State 31 and Prati 32) at the new EGS demonstration area. Our modeling indicates that the proposed injection scheme will provide additional steam production in the area by creating a zone of permeability enhancement extending about 0.5 km from each injection well which will connect to the overlying conventional steam reservoir, in agreement with the conclusions of Nielson and Moore (2000).

  8. The impact of cancer incidence and stage on optimal utilization of radiotherapy: Methodology of a population based analysis by the ESTRO-HERO project.

    Science.gov (United States)

    Borras, Josep M; Barton, Michael; Grau, Cai; Corral, Julieta; Verhoeven, Rob; Lemmens, Valery; van Eycken, Liesbet; Henau, Kris; Primic-Zakelj, Maja; Strojan, Primoz; Trojanowski, Maciej; Dyzmann-Sroka, Agnieszka; Kubiak, Anna; Gasparotto, Chiara; Defourny, Noemie; Malicki, Julian; Dunscombe, Peter; Coffey, Mary; Lievens, Yolande

    2015-07-01

    The impact of differences in the distribution of major cancer sites and stages at diagnosis among 4 European countries on the optimal utilization proportion (OUP) of patients who should receive external beam radiotherapy was assessed within the framework of the ESTRO-HERO project. Data from Australian Collaboration for Cancer Outcomes Research and Evaluation (CCORE) were used. Population based stages at diagnosis from the cancer registries of Belgium, Slovenia, the Greater Poland region of Poland, and The Netherlands were used to assess the OUP for each country. A sensitivity analysis was carried out. The overall OUP by country varied from the lowest of 48.3% in Australia to the highest of 53.4% in Poland; among European countries the variation was limited to 3%. Cancer site specific OUPs showed differences according to the variability in stage at diagnosis across countries. The most important impact on the OUP by country was due to changes in relative frequency of tumours rather than stage at diagnosis. This methodology can be adapted using European data, thus facilitating the planning of resources required to cope with the demand for radiotherapy in Europe, taking into account the national variability in cancer incidence. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  9. Application of IT-technologies in visualization of innovation project life-cycle stages during the study of the course "Management of innovation projects"

    Science.gov (United States)

    Kolychev, V. D.; Prokhorov, I. V.

    2017-01-01

    The article presents a methodology for the application of IT-technologies in teaching discipline "Management of innovation projects," which helps students to be more competitive and gather the useful skills for their future specialization in high-tech areas. IT-technologies are widely used nowadays in educational and training spheres especially in knowledge-intensive disciplines such as systems analysis, the theory of games, operations research, theory of risks, innovation management etc. For studying such courses it is necessary to combine both mathematical models and information technology approaches for the clear understanding of the investigated object. That is why this article comprises both the framework of research and the IT-tools for investigation in the educational process. Taking into consideration the importance of the IT-system implementation especially for the university we assume to suggest the methods of research in the area of innovation projects with the help of IT-support.

  10. Hood River and Pelton Ladder Monitoring and Evaluation Project and Hood River Fish Habitat Project : Annual Progress Report 1999-2000.

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, Michael B.; McCanna, Joseph P.; Jennings, Mick

    2001-02-01

    The Hood River subbasin is home to four species of anadromous salmonids: chinook salmon (Oncorhynchus tshawytscha), coho salmon (Oncorhynchus kisutch), steelhead (Oncorhynchus mykiss), and sea run cutthroat trout (Salmo clarki). Indigenous spring chinook salmon were extirpated during the late 1960's. The naturally spawning spring chinook salmon currently present in the subbasin are progeny of Deschutes stock. Historically, the Hood River subbasin hatchery steelhead program utilized out-of-basin stocks for many years. Indigenous stocks of summer and winter steelhead were listed in March 1998 by National Marine Fisheries Service (NMFS) under the Endangered Species Act (ESA) as a ''Threatened'' Species along with similar genetically similar steelhead in the Lower Columbia Basin. This annual report summarizes work for two consecutive contract periods: the fiscal year (FY) 1999 contract period was 1 October, 1998 through 30 September, 1999 and 1 October, 1999 through 30 September, 2000 for FY 2000. Work implemented during FY 1999 and FY 2000 included (1) acclimation of hatchery spring chinook salmon and hatchery summer and winter steelhead smolts, (2) spring chinook salmon spawning ground surveys on the West Fork Hood River (3) genetic analysis of steelhead and cutthroat [contractual service with the ODFW], (4) Hood River water temperature studies, (5) Oak Springs Hatchery (OSH) and Round Butte Hatchery (RBH) coded-wire tagging and clipping evaluation, (6) preparation of the Hood River Watershed Assessment (Coccoli et al., December 1999) and the Fish Habitat Protection, Restoration, and Monitoring Plan (Coccoli et al., February 2000), (7) project implementation of early action habitat protection and restoration projects, (8) Pelton Ladder evaluation studies, (9) management oversight and guidance to BPA and ODFW engineering on HRPP facilities, and (10) preparation of an annual report summarizing project objectives for FY 1999 and FY 2000.

  11. ENVIRONMENT PROTECTION AND ENVIRONMENT MONITORING ISSUES IN THE PROJECTS OF SUBGLACIAL LAKES STUDIES IN ANTARCTICA

    Directory of Open Access Journals (Sweden)

    I. A. Alekhina

    2012-01-01

    Full Text Available Antarctic subglacial lakes can represent extreme natural habitats for microorganisms from the position of their evolution and adaptation, as well as they can contain the information on Antarctic ice sheet history and climatic changes in their sediments. Now only direct measurements and sampling from these habitats can answer on many fundamental questions. Special precaution should be complied at penetration into these unique relic environments without unfavorable impacts and contamination. A number of recommendations were developed on levels of cleanliness and sterility during direct exploration and research of subglacial environments. Documents considered in the article are the first and necessary steps for appropriate and long-term ecological management of subglacial Antarctic environments. Today there are three projects of subglacial aquatic environment research which are in preparation and realization – the Russian project of Lake Vostok, the similar British project of Lake Ellsworth and the American project on Whillans Ice Stream. The programs of ecological stewardship for direct exploration of these lakes are discussed. All these subglacial aquatic objects of further exploration and research are so various on their structure, age and regime, that only results of all programs as a whole can help to draw us a uniform picture of a subglacial ecological system. Ecological stewardship of these should provide the minimal ecological impact with maximal scientific results. On the basis of existing documents and recommendations the general approaches and the program of ecological stewardship for Lake Vostok research are discussed. Study of drilling fluid, drilling chips, Vostok ice core and the fresh frozen water will allow to make an assessment of biological and chemical contamination as a result of the first penetration and to modify the further stewardship program for the second penetration and direct exploration of lake water.

  12. 再议房地产项目设计阶段成本控制%Review the Cost Control in Design Stage of Real Estate Project

    Institute of Scientific and Technical Information of China (English)

    朱双颖; 刘亮; 李煊午

    2013-01-01

    设计阶段的成本控制是房地产项目控制的重点,本文通过对国内研究成果的阐述及国外研究经验借鉴,为我国设计阶段成本控制提供一些确实有效的方法.%Cost control in design stage methods is key issue of the real estate project.This paper proposes some effective cost control methods based on domestic study and foreign research achievements and experiences.

  13. Milliken Clean Coal Technology Demonstration Project. Environmental monitoring report, July--September 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    New York State Electric and Gas Corporation (NYSEG) has installed and is presently operating a high-efficiency flue gas desulfurization (FGD) system to demonstrate innovative emissions control technology and comply with the Clean Air Act Amendments of 1990. The host facility for this demonstration project is NYSEG`s Milliken Station, in the Town of Lansing, New York. The primary objective of this project is to demonstrate a retrofit of energy-efficient SO{sub 2} and NO{sub x} control systems with minimal impact on overall plant efficiency. The demonstration project has added a forced oxidation, formic acid-enhanced wet limestone FGD system, which is expected to reduce SO{sub 2} emissions by at least 90 percent. NYSEG also made combustion modifications to each boiler and plans to demonstrate selective non-catalytic reduction (SNCR) technology on unit 1, which will reduce NO{sub x} emissions. Goals of the proposed demonstration include up to 98 percent SO{sub 2} removal efficiency while burning high-sulfur coal, 30 percent NO{sub x} reductions through combustion modifications, additional NO{sub x} reductions using SNCR technology, production of marketable commercial-grade gypsum and calcium chloride by-products to minimize solid waste disposal, and zero wastewater discharge.

  14. Milliken Clean Coal Technology Demonstration Project. Environmental monitoring report, July--September 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    New York State Electric and Gas Corporation (NYSEG) has installed and is presently operating a high-efficiency flue gas desulfurization (FGD) system to demonstrate innovative emissions control technology and comply with the Clean Air Act Amendments of 1990. The host facility for this demonstration project is NYSEG`s Milliken Station, in the Town of Lansing, New York. The primary objective of this project is to demonstrate a retrofit of energy-efficient SO{sub 2} and NO{sub x} control systems with minimal impact on overall plant efficiency. The demonstration project has added a forced oxidation, formic acid-enhanced wet limestone FGD system, which is expected to reduce SO{sub 2} emissions by at least 90 percent. NYSEG also made combustion modifications to each boiler and plans to demonstrate selective non-catalytic reduction (SNCR) technology on unit 1, which will reduce NO{sub x} emissions. Goals of the proposed demonstration include up to 98 percent SO{sub 2} removal efficiency while burning high-sulfur coal, 30 percent NO{sub x} reductions through combustion modifications, additional NO{sub x} reductions using SNCR technology, production of marketable commercial-grade gypsum and calcium chloride by-products to minimize solid waste disposal, and zero wastewater discharge.

  15. Tank monitor and control system (TMACS) year 2000 compliance project plan

    Energy Technology Data Exchange (ETDEWEB)

    HOLM, M.J.

    1999-06-24

    The purpose of this document is to describe tests performed to validate Revision 11 of the Tank Monitor and Control System (TMACS) and verify that the software functions as intended by design. This document is intended to test the software portion of TMACS. The tests will be performed on the development system. The software to be tested is the TMACS knowledge bases (KB) and the I/O driver/services. The development system will not be talking to field equipment; instead, the field equipment is simulated using emulators or multiplexers in the lab.

  16. Uranium Mill Tailings Remedial Action Project Annual Environmental Monitoring Report calendar year 1992: Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    None

    1993-12-31

    This report describes environmental monitoring and compliance at eight UMTRA sites where remedial action was underway during 1992 and at the ten sites that were complete at the end of 1992. Volume I contains information for Ambrosia Lake, NM; Cannonsburg/Burrell, PA; Durango, CO; Falls City, TX; Grand Junction, CO; Green River, UT; and Gunnison, CO. Each site report contains a site description, compliance summary, environmental program information, environmental radiological and non-radiological program information, water resources protection, and quality assurance information.

  17. The Lick AGN Monitoring Project: Reverberation Mapping of Optical Hydrogen and Helium Recombination Lines

    CERN Document Server

    Bentz, Misty C; Barth, Aaron J; Yoshii, Yuzuru; Woo, Jong-Hak; Wang, Xiaofeng; Treu, Tommaso; Thornton, Carol E; Street, Rachel A; Steele, Thea N; Silverman, Jeffrey M; Serduke, Frank J D; Sakata, Yu; Minezaki, Takeo; Malkan, Matthew A; Li, Weidong; Lee, Nicholas; Hiner, Kyle D; Hidas, Marton G; Greene, Jenny E; Gates, Elinor L; Ganeshalingam, Mohan; Filippenko, Alexei V; Canalizo, Gabriela; Bennert, Vardha Nicola; Baliber, Nairn

    2010-01-01

    We have recently completed a 64-night spectroscopic monitoring campaign at the Lick Observatory 3-m Shane telescope with the aim of measuring the masses of the black holes in 12 nearby (z < 0.05) Seyfert 1 galaxies with expected masses in the range ~10^6-10^7M_sun and also the well-studied nearby active galactic nucleus (AGN) NGC 5548. Nine of the objects in the sample (including NGC 5548) showed optical variability of sufficient strength during the monitoring campaign to allow for a time lag to be measured between the continuum fluctuations and the response to these fluctuations in the broad Hbeta emission, which we have previously reported. We present here the light curves for the Halpha, Hgamma, HeII 4686, and HeI 5876 emission lines and the time lags for the emission-line responses relative to changes in the continuum flux. Combining each emission-line time lag with the measured width of the line in the variable part of the spectrum, we determine a virial mass of the central supermassive black hole fro...

  18. Ambient intelligence for monitoring and research in clinical neurophysiology and medicine: the MIMERICA* project and prototype.

    Science.gov (United States)

    Pignolo, L; Riganello, F; Dolce, G; Sannita, W G

    2013-04-01

    Ambient Intelligence (AmI) provides extended but unobtrusive sensing and computing devices and ubiquitous networking for human/environment interaction. It is a new paradigm in information technology compliant with the international Integrating Healthcare Enterprise board (IHE) and eHealth HL7 technological standards in the functional integration of biomedical domotics and informatics in hospital and home care. AmI allows real-time automatic recording of biological/medical information and environmental data. It is extensively applicable to patient monitoring, medicine and neuroscience research, which require large biomedical data sets; for example, in the study of spontaneous or condition-dependent variability or chronobiology. In this respect, AML is equivalent to a traditional laboratory for data collection and processing, with minimal dedicated equipment, staff, and costs; it benefits from the integration of artificial intelligence technology with traditional/innovative sensors to monitor clinical or functional parameters. A prototype AmI platform (MIMERICA*) has been implemented and is operated in a semi-intensive unit for the vegetative and minimally conscious states, to investigate the spontaneous or environment-related fluctuations of physiological parameters in these conditions.

  19. Annual report for RCRA groundwater monitoring projects at Hanford Site facilities for 1995

    Energy Technology Data Exchange (ETDEWEB)

    Hartman, M.J.

    1996-02-01

    This report presents the annual hydrogeologic evaluation of 19 Resource Conservation and Recovery Act of 1976 facilities and 1 nonhazardous waste facility at the US Department of Energy`s Hanford Site. Although most of the facilities no longer receive dangerous waste, a few facilities continue to receive dangerous waste constituents for treatment, storage, or disposal. The 19 Resource Conservation and Recovery Act facilities comprise 29 waste management units. Nine of the units are monitored under groundwater quality assessment status because of elevated levels of contamination indicator parameters. The impact of those units on groundwater quality, if any, is being investigated. If dangerous waste or waste constituents have entered groundwater, their concentration profiles, rate, and extent of migration are evaluated. Groundwater is monitored at the other 20 units to detect leakage, should it occur. This report provides an interpretation of groundwater data collected at the waste management units between October 1994 and September 1995. Groundwater quality is described for the entire Hanford Site. Widespread contaminants include nitrate, chromium, carbon tetrachloride, tritium, and other radionuclides.

  20. Project on Restaurant Energy Performance: end-use monitoring and analysis

    Energy Technology Data Exchange (ETDEWEB)

    Claar, C.N.; Mazzucchi, R.P.; Heidell, J.A.

    1985-05-01

    Although energy bills for restaurants throughout the United States exceed 5 billion dollars annually, very little has been documented with respect to when and how restaurants use energy, or how such use can be reduced cost-effectively. This report summarizes the results of a multiyear collaborative research effort, designed to collect information on end-use energy consumption. Objective is to reveal the quantities and profiles of energy consumption of typical food service operations by time of day and end use. This information, when examined in conjunction with building characteristics, allows detailed study of energy use cause and effect and energy conservation potential. Seven representative monitoring sites were selected, a computerized data acquisition network was designed and implemented, and detailed energy performance was compiled for a 1 year period (July 1983 through June 1984). Each of the seven facilities monitored was selected to represent the seven most common restaurant types and to provide information on a wide variety of commonly used restaurant equipment. Preliminary findings are presented.