Digital terrestrial experimental television broadcasting studio system; Chijo digital jikken hoso soshutsu kiki

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Ahead of the start of the full digital terrestrial broadcasting scheduled for fiscal 2003, the Ministry of Posts and Telecommunications structured experimental systems in seven areas over the nation's land. The Company has received orders for four areas, and developed and supplied the pieces of equipment and devices. The system consists mainly of the following components: (1) an encoder to compress image signals into the moving picture experts Group 2 (MPEG2) signals; (2) a rate-free matrix to select signals for images and MPEG2 signals (an assembly of changeover switches); (3) a multiplexing device to multiplex MPEG2 signals; (4) a multi-rate server to accumulate and regenerate the MPEG2 signals; (5) an orthogonal frequency division multiplex (OFDM) modulator to modulate the multiplexed MPEG2 signals; (6) a splicer to switch the MPEG2 signals without interruption; and (7) an integrated control system to control MPEG2 devices. (translated by NEDO)

Performance of bismuth tape current leads under vibration; Bi tepu sei denryu rido no shindo tokusei

Energy Technology Data Exchange (ETDEWEB)

Suzuki, E.; Kurihara, M. [Railway Techniical Research Institute, Tokyo (Japan)

2000-02-25

The superconducting magnets on Maglev vehicles when running vibrate mechanically due to electromagnetic disturbance from the ground coils. Therefore, the current leads fixed on the superconducting coil, which is vibration at about 98 m/s{sup 2} (=10g), are also required to endure the vibration. We executed dynamic vibration tests for two types of current leads (straight and arc types) which had a multi-stacked configuration of Ag-sheathed Bi2223 tapes impregnated with epoxy resin in a concaved reinforcing gutter. We evaluated the straight-type lead for an operating current of 700 A after every vibration test in liquid nitrogen for one hour under the dynamic strain deformation of 50-100 {mu} on the surface of the reinforcing material covering the current lead. We could not detect degradation of the current lead by vibration through the total cycles of 3.9 x 10{sup 6} after continuous vibration tests. We also executed vibration tests for arc-type current leads which were combined with an actual energized superconducting coil for a Maglev. Large accelerations of these current leads occurred at frequencies of 308 and 375 Hz. In spite of the maximum acceleration of 600-700 m/s{sup 2} generated by actuating the excessive force on a superconducting coil for two seconds, which occurred on these current leads carrying 500 A, the superconductivity of the current leads did not shift to normal conductivity. There was no damage to either type of current lead during these vibration tests. So we confirmed the good prospect for the application of these current leads to actual Maglev superconducting magnets. (author)

Vibration control of bridges and buildings hybrid system. Kyoryoter dot tatemono no shindo seigyo hybrid hoshiki

Energy Technology Data Exchange (ETDEWEB)

Tanida, K. (Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan))

1991-11-15

Multistory buildings, suspension bridges, and cable stayed bridges tend to become huge, and technology of controlling their vibration caused by strong winds and earthquakes is becoming an important subject for study. A description is made on a hybrid system which is a combination of the conventional passive system and active system, having merits of both of the systems. Verification test made using a model and an example of application to an actual bridge are introduced. This hybrid control system has been applied to the main tower of the cable stayed bridge on Route 12 of the Tokyo expressway. It is installed and in operation on the top of the tower to improve the workability, and can decrease the vibration of the tower caused by vortical excitation produced during the construction of the main tower. With the hybrid system, the actuator capacity can be reduced to about 1/5 for the similar damping performance to that of the active system with the same mass ratio. In addition, the weight of the equipment can be nearly halved in comparison with the passive system. Moreover, it has such a high safety characteristic as being used as a passive system when power supply is cut off because the controlling force of the system is smaller as compared with the active system. 2 refs., 11 figs.

Actual proof study of energy autonomous house; Energy jiritsu house no jissho jikken. 1

Energy Technology Data Exchange (ETDEWEB)

Masuzawa, O; Masuzawa, C

1997-11-25

A discussion was given on an `energy autonomous house` which utilizes more effectively photovoltaic power generation, solar heat and light in designing a wooden house to be built by using the conventional construction method. According to the plan, photovoltaic power generation modules and heat collectors are installed superimposed on a roof facing south. Heat-collected air is sent below the floor and the heat is stored in the concrete in winter, utilized as the floor heating type room heater. The hot air is used for hot water supply in other seasons. The building is of two stories with a total area of 118 m {sup 2}, and the photovoltaic generation capacity is 3.48 kW. The photovoltaic generation amount was calculated from insolation forecasted by the AMEDAS system, and energy balance of this house was estimated. The result therefrom may be summarized as follows: total energy supplied reached 11.6 Gcal, signifying that about 10.8% of the energy irradiated onto the building is utilized; ratio of the photovoltaic and solar heat utilization is 27% versus 73%; and energy consumption in this house was estimated and calculated from actual results, airtightness and adiabatic performance of old houses, whereas the energy autonomous rate has reached 92.8%. 5 refs., 2 figs., 8 tabs.

Experiments on Ion-Ion Plasmas From Discharges

Science.gov (United States)

Leonhardt, Darrin; Walton, Scott; Blackwell, David; Murphy, Donald; Fernsler, Richard; Meger, Robert

2001-10-01

Use of both positive and negative ions in plasma processing of materials has been shown to be advantageous[1] in terms of better feature evolution and control. In this presentation, experimental results are given to complement recent theoretical work[2] at NRL on the formation and decay of pulsed ion-ion plasmas in electron beam generated discharges. Temporally resolved Langmuir probe and mass spectrometry are used to investigate electron beam generated discharges during the beam on (active) and off (afterglow) phases in a variety of gas mixtures. Because electron-beam generated discharges inherently[3] have low electron temperatures (<0.5eV in molecular gases), negative ion characteristics are seen in the active as well as afterglow phases since electron detachment increases with low electron temperatures. Analysis of temporally resolved plasma characteristics deduced from these measurements will be presented for pure O_2, N2 and Ar and their mixtures with SF_6. Oxygen discharges show no noticeable negative ion contribution during the active or afterglow phase, presumably due to the higher energy electron attachment threshold, which is well above any electron temperature. In contrast, SF6 discharges demonstrate ion-ion plasma characteristics in the active glow and are completely ion-ion in the afterglow. Comparison between these discharges with published cross sections and production mechanisms will also be presented. [1] T.H. Ahn, K. Nakamura & H. Sugai, Plasma Sources Sci. Technol., 5, 139 (1996); T. Shibyama, H. Shindo & Y. Horiike, Plasma Sources Sci. Technol., 5, 254 (1996). [2] See presentation by R. F. Fernsler, at this conference. [3] D. Leonhardt, et al., 53rd Annual GEC, Houston, TX.

'Twenty-five years after Chernobyl accident: Safety for the future'. 2011 National report of Ukraine

International Nuclear Information System (INIS)

Imanaka, Tetsuji; Shindo, Mahito

2016-02-01

This is the Japanese translation of the Ukrainian National Report 'Twenty-five Years after Chernobyl Accident: Safety for the Future', published by the Ministry of Ukraine of Emergencies in 2011 (in Ukrainian and English). This Japanese translation is published as an outcome of the KAKENHI research project on liquidations of Nuclear Disasters in the World (headed by Tetsuji Imanaka), in which Shindo participates, and as a KUR report of the Research Reactor Institute at Kyoto University. The objective of publishing this Japanese translation is to provide basic information on how to overcome the consequences of a large-scale Nuclear Disaster for the wide range of public, including decision-makers and administrative staff. By doing so, this publication aims at invigorating discussions over measures to be applied for overcoming the consequences of the TEPCO Nuclear Disaster (started in 11th March 2011 at Fukushima), and at forming proper schemes to minimise the consequences on current and future generations. The original text of this translation tightly summarised the whole picture of the Chernobyl Nuclear Disaster, which had been the only large-scale Nuclear Disaster until 11th March 2011. More importantly, it describes all sorts of measures and schemes taken in Ukraine from 1986 to 2011 in order to overcome the consequences of the Chernobyl Nuclear Disaster, in a quite well structured manner. In other words, from the contents of this text, Japanese readers are able to learn a lot about the very problems currently facing with. Therefore, I wish many Japanese readers will read this text, and utilise the knowledge written here effectively to overcome the consequences of the TEPCO Nuclear Disaster. (J.P.N.)

Unstable roll motions by parametric resonance in following seas. Keisu reiki shindo ni motozuku oinamichu fuantei yokoyure

Energy Technology Data Exchange (ETDEWEB)

Ishiguro, T.; Ito, A.; Mizoguchi, S. (Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan))

1991-05-01

The unstable rolling region and angle in the regular waves were studied by both tank test modeling a large container ship and theoretical calculation based on Mathieu{prime}s equation. Further research was made on the influence of metacentric height (GM) under the calm sea condition, ship speed and bilge keel dimension on the unstable rolling region. To avoid the unstable roll motion in the waves caused by the parametric resonance, the fluctuation in GM is designed to be diminished on the waves by U-shaping the hull fore and aft like a fat large ship hull, or the fluctuation in dynamic stability is done to be diminished by increasing the GM on the calm sea. However, the ship with a U-shaped hull fore and aft is large in rolling angle due to the smallness in righting arm at the large heeling angle. Generally regardless of oceanic condition and ship speed, it is impossible to establish the GM absolutely without the primary and secondary synchronizing points. To avoid the unstable roll motion with a low ship speed, it is desirable to do it by the ship speed to be as high as possible. 11 refs., 13 figs., 1 tab.

Vibration measurement for evaluating the danger of rock-collapse; Rakuseki kikendo hantei no tame no shindo sokutei

Energy Technology Data Exchange (ETDEWEB)

Takeuchi, T; Harada, H [The Nippon Road Co. Ltd., Tokyo (Japan); Mitsuzuka, T [Chishitsu-Keisoku Co. Ltd., Tokyo (Japan)

1997-10-22

Discussions were given on feasibility of a method for investigating a problem of the danger of rock-collapse by applying vibration measurement. The measurement investigation was carried out at a mouth of a tunnel under construction on a highway where the danger of rock-collapse is being investigated according to a qualitative determination criterion. Sixty-four rocks have been evaluated of their danger, with the degree of the danger having been classified to ranks one to three. Vibration measurement was performed on five floating rocks out of the 64 rocks. Vibroscopes were installed on upper portion of the rocks to be investigated and on exposed rocks nearby. The measurement revealed that the vibration has nearly the same amplitude in both of the floating rocks and the settled rocks before and after an automobile has passed, but the floating rocks shake more strongly than the settled rocks while an automobile is passing. This trend appears more noticeably in rocks regarded unstable in the danger determining investigation, indicating presence of close relationship between wave amplitude excited by the automobile and adhesion of the floating rocks. As a result of the discussions, it was made clear that the maximum amplitude ratio and the spectral ratio among the vibration characteristics of the floating rocks can be used as effective determination criteria. 2 refs., 7 figs., 2 tabs.

Prediction of blast vibration level considered propagation characteristics; Denpa tokusei to koryoshita happa shindo level no yosoku

Energy Technology Data Exchange (ETDEWEB)

Kunimatsu, S; Jinguji, M [National Institute for Resources and Environment, Tsukuba (Japan); Yamada, M; Hirai, T [Newjec Inc., Osaka (Japan); Durucan, S; Farsangi, M

1997-10-22

With an objective to assess environmental influence induced by blast vibration, a study has been carried out on a method to predict vibration levels. The study has discussed a method to calculate vibration levels, in which vibration propagating characteristics are sought on blast vibration generated from an open-cut limestone mine from acceleration waveforms in the vicinity of the blast source and residential housings by using an octave analysis, and waveforms are predicted. The shortest straight line distance from the blast position to a housing is about 150 m, and the height difference is about 30 to 40 meters. The measuring instruments include a vibration level meter used for pollution measurement and a data recorder, with signals lower than 1 Hz and higher than 90 Hz being interrupted. The environmental influence assessment discusses not only the maximum value of the vibration level, but also sizes of values of each band by using a frequency analysis. The result of the discussions revealed that the prediction of the vibration levels is little affected by phase characteristics, and that no problems are caused in the measurement accuracy even if the vibration levels are predicted by using relative decay amount according to a one-third octave analysis for the propagation characteristics. 5 figs., 4 tabs.

Numerical experiment for nonlinear full-wave tomography. 3; Hisenkei full wave tomography no suchi jikken

Energy Technology Data Exchange (ETDEWEB)

Tsuchiya, T [Dia Consultants Company, Tokyo (Japan)

1996-10-01

Nonlinear full-wave tomography (FWT) is under investigation to improve the estimation accuracy of Vp/Vs distributions. Full-wave tomography is one of the underground structure exploration methods mainly using Tarantola`s nonlinear local optimization method (LOM). Numerical experiment for FWT was carried out assuming relatively weak nonlinear underground structure. In the case of inversion by local optimization method, adequate preconditioning is important. Utilization of geological information is also effective in estimating low-frequency components of a model. As far as data are obtained under proper observation arrangement, even in actual field, precise estimation of Vp/Vs distributions is possible by FWT using explosion in a hole as wave source. In full-wave tomography, selection of observation arrangement is essential for both Vp and Vs. However, the proper arrangement is different between Vp and Vs. Approach to different analyses for Vp and Vs is also necessary by using only proper data for Vp and Vs among obtained data sets. 4 figs.

Experimental report of precast prestressed concrete shear wall. Precast prestressed concrete taishinheki no jikken hokoku

Energy Technology Data Exchange (ETDEWEB)

Takada, K.; Komura, M.; Sakata, H.; Senoo, M. (Fudo Building Research Co. Ltd., Tokyo (Japan))

1993-07-30

The present report outlines the multi-story precast prestressed concrete earthquake-proof wall (PC shear wall system). The PC shear wall is a precast wall which internally contains the columns and beams as a unit. Therefore, the present system integrates the walls, columns and beams without beam-framing installation for the intermediate stories. It can simplify the concreting in site and ease the construction of building. For the system development, experiment was made on the deformation, sliding, yield strength and destruction state of the shear wall. Used were four types of test unit which are different in both reinforcement and connection methods. The test force was given by a hydraulically drawing jack. In the experiment, the four types were compared in destruction state, relation between load and deformation, yield strength, and strain of main column reinforcing bars and wall connection reinforcing bars. PC shear wall system-based design was studied from the experimental result. The shear wall in which there occurred both bending and shearing deformations was modeled by changing to a brace unit. Divided into bending deformation and shearing deformation, the deformation was calculated, which concluded that the shearing deformation dominates in the present system. 15 figs., 4 tabs.

Individualizing risk of multidrug-resistant pathogens in community-onset pneumonia.

Directory of Open Access Journals (Sweden)

Marco Falcone

Full Text Available The diffusion of multidrug-resistant (MDR bacteria has created the need to identify risk factors for acquiring resistant pathogens in patients living in the community.To analyze clinical features of patients with community-onset pneumonia due to MDR pathogens, to evaluate performance of existing scoring tools and to develop a bedside risk score for an early identification of these patients in the Emergency Department.This was an open, observational, prospective study of consecutive patients with pneumonia, coming from the community, from January 2011 to January 2013. The new score was validated on an external cohort of 929 patients with pneumonia admitted in internal medicine departments participating at a multicenter prospective study in Spain.A total of 900 patients were included in the study. The final logistic regression model consisted of four variables: 1 one risk factor for HCAP, 2 bilateral pulmonary infiltration, 3 the presence of pleural effusion, and 4 the severity of respiratory impairment calculated by use of PaO2/FiO2 ratio. A new risk score, the ARUC score, was developed; compared to Aliberti, Shorr, and Shindo scores, this point score system has a good discrimination performance (AUC 0.76, 95% CI 0.71-0.82 and calibration (Hosmer-Lemeshow, χ2 = 7.64; p = 0.469. The new score outperformed HCAP definition in predicting etiology due to MDR organism. The performance of this bedside score was confirmed in the validation cohort (AUC 0.68, 95% CI 0.60-0.77.Physicians working in ED should adopt simple risk scores, like ARUC score, to select the most appropriate antibiotic regimens. This individualized approach may help clinicians to identify those patients who need an empirical broad-spectrum antibiotic therapy.

Prediction of powerplant vibration using FRF data of FE model; Dentatsu kansu wo mochiita power plant shindo yosoku

Energy Technology Data Exchange (ETDEWEB)

Suzuki, T; Tsukahara, M; Sakaguchi, M; Takahashi, Y [Honda R and D Co. Ltd., Tokyo (Japan)

1997-10-01

For the purpose of shortening the development period, the estimation of powerplant vibration has become more important in the early design stage, and eigenvalue analysis by FEM is commonly used to solve this problem. Eigenvalue Analysis cannot directly predict vibration levels under running conditions that affect the durability of each component and the vibration of a car body. This paper presents a new approach using FRF data from FE models for accurate prediction of engine vibration under running conditions. By applying this approach to an in-line four cylinder engine, the predicted vibration is reasonably comparable with experimental results. 3 refs., 8 figs.

Noise and vibration reduction technology in hybrid vehicle development; Hybrid sha kaihatsu ni okeru shindo soon teigen gijutsu

Energy Technology Data Exchange (ETDEWEB)

Yoshioa, T.; Sugita, H. [Toyota Motor Corp., Aichi (Japan)

2000-03-01

Accomplishing both environmental protection and good NVH performance has become a significant task in automotive development The first-in-the-world hybrid passenger car of mass production. 'Prius', has achieved superior NV performance compared with conventional vehicles with a 1.5-liter engine along with 50% reduction of fuel consumption and CO{sub 2} emissions. low HC, CO and NO{sub x} emissions. This paper describes NV reduction technology for solving problems peculiar to the hybrid vehicle such as engine start/stop vibration, drone noise at low engine speed and motor/generator noise and vibration. It also mentions application technology of low rolling resistance tires with light weight wheels and recycled material for sound proofing. (author)

Magnetotelluric (MT) surveying in the Kakkonda geothermal area; Kakkonda chinetsu chiiki deno MT ho tansa jikken

Energy Technology Data Exchange (ETDEWEB)

Ogawa, Y; Takakura, S [Geological Survey of Japan, Tsukuba (Japan); Uchida, T [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

1997-05-27

This paper describes the MT surveying conducted at the vicinity of a deep well (WD-1) in the Kakkonda geothermal area. For the MT surveying, the interval between measuring points was 300 m. Electric field dipole with a length of 300 m was given in the direction of traverse line, and that with a length of 50 m was given in the direction perpendicular to the line. Three components of magnetic field were measured using induction coil. Frequency band of the data was between 0.0005 Hz and 300 Hz. Characteristics of specific resistance model obtained from the MT surveying were illustrated. Low specific resistance zone less than 30 ohm-m was observed in the shallow zone below the altitude 0 m. This zone was comparable to the distribution of montmorillonite. High specific resistance anomaly was analyzed at the western half of the traverse line in the altitude between 0 m and -2000 m, which corresponded to the collective part of focuses. The bottom surface of the anomaly agreed well with the upper surface of neo-granite, i.e., the lower limits of earthquakes. Low specific resistance was observed in the altitude below -2000 m. 17 refs., 5 figs.

Method for analyzing electromagnetic-force-induced vibration and noise analysis; Denjiryoku reiki ni yoru dendoki no shindo hoshaon kaisekiho

Energy Technology Data Exchange (ETDEWEB)

Shiohata, K.; Nemoto, K.; Nagawa, Y.; Sakamoto, S.; Kobayashi, T.; Ito, M.; Koharagi, H. [Hitachi, Ltd, Tokyo (Japan)

1998-11-01

In this analysis method, electromagnetic force calculated by 2-dimensional analysis is transformed into external force for 3-dimensional structural-vibration analysis. And a modeling procedure for a vibrating structure is developed. Further, a space-modal-resonance criteria which relates electromagnetic force to structural-vibration or noise is introduced. In the structural-vibration analysis, the finite element method is used; and in the noise analysis, the boundary element method is used. Finally, vibration and noise of an induction motor are calculated using this criteria. Consequently, high-accuracy modeling is achieved and noise the calculated by the simulation almost coincides with that obtained by experiments. And it is clarified that the-space-modal resonance criteria is effective in numerical simulation. 11 refs., 9 figs., 3 tabs.

Prediction of vibration level in tunnel blasting; Tonneru kusshin happa ni yotte reiki sareru shindo no reberu yosoku ho

Energy Technology Data Exchange (ETDEWEB)

Hirata, A. [Kumamoto Industries Univ, Kumamoto (Japan); Yamamoto, M. [Asahi Chemical Industry Co. Ltd., Tokyo (Japan); Inaba, C. [Nishimatsu Construction Co. Ltd., Kanagawa (Japan); Kaneko, K. [Hokkaido Univ (Japan)

1997-08-01

For avoiding the generation of public hazard due to ground vibration causes by blasting in tunneling, it is important to devise a blasting method for ensuring the level of the ground vibration caused thereby under a limit, and an exact predication of ground vibration before blasting is desirable. In this study, the characteristics of the ground vibration caused by tunnel blasting are analyzed, and a summary of amplitude spectra calculating method is described. A theoretical analysis method for predicting the vibration level is proposed based on spectrum-multiplicative method. Vibration caused by multistage blasting in tunneling is most strong and deemed as important. When observing the process of elastic wave motion caused by multistage blasting being measured, the process can be divided into three element processes in frequency area as vibration source spectrum, transmission attenuation spectrum and frequency response function vibrating test, and, with the multiplication of them, the amplitude spectra at an observation portion can be estimated. 12 refs., 12 figs.

On noise, traffic and factory vibrations in Akita city; Akitashi ni okeru soon oyobi kotsu kojo shindo ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Nogoshi, M; Kikuchi, T; Morino, T; Sannohe, M [Akita University, Akita (Japan). College of Education

1996-05-01

Noise and vibration were measured in Akita City. In 1994, noise and traffic-caused vibration were measured along the trunk lines and other roads across the entire Akita City area. In 1995, the effort centered on the Ibarashima manufacturing quarters, the important source of noise and vibration in Akita city. The general-purpose noise meter LA-220S was used to measure noise and the vibration level meter VR-5100 was used to measure vibration. The results of noise measurement carried out at 122 points in Akita City indicated that the noise level was high along Route 7, Route 13, and the southern line belonging to the newly built national highway, marking the highest of approximately 74dB. As compared with the measurement made in 1968, the value was higher by 3-13dB. A roughly similar trend was seen in vibration. The noise level measurement of 1995 accomplished at 100 points in the vicinity of Ibarashima district indicated that the factories were responsible for high levels of noise and vibration. It was found that the levels lowered in proportion to the increase in the distance from the factories. 11 figs., 1 tab.

Consideration on local blast vibration control by delay blasting; Danpatsu happa ni yoru kyokuchiteki shindo seigyo ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Mogi, Gento; Adachi, Tsuyoshi; Yamatomi, Jiro [The University of Tokyo School of Engineering Department of Geosystem Engineering, Tokyo (Japan); Hoshino, Tatsuya [Mitsui Mining and Smelting Corp., Tokyo (Japan)

1999-10-31

In this research, local blast vibration control based on the theory of superposition of waves was investigated. Firstly, the influence of delay time errors of conventional electric detonators upon the level of local blast vibration was examined. Secondly, for a further effective local blast vibration control, a new delay blasting design concept 'combined delay blasting' that postulates the use of electronic detonators, which virtually have no delay time errors, is proposed. For a delay blasting with uniform detonation time intervals, an optimum time interval to minimize the local PPV (Peak Particle Velocity) is obtained based on the relationship between the PPV and the time interval, which is derived by superposing identical vibration time histories of each single hole shot. However, due to the scattering of the actual delay time caused by errors, PPV of a production blast seldom coincides with the estimated one. Since the expected value and the variance of PPV mainly depend on sensitivity of PPV around the nominal delay time, it is proposed that not only the optimum but also several sub-optimum candidates of delay time should be examined taking error into consideration. Concerning the 'combined delay blasting', its concept and some simulation results are presented. The estimated reduction effect of blast vibration of a delay blast based on this concept was quite favorable, indicating a possibility for further effective local blast vibration control. (author)

Wind tunnel investigation of a USB-STOL transport semi-span model. 2; CAD sekkei ni yoru USB-STOL ki hansai mokei no fudo shiken. 2

Energy Technology Data Exchange (ETDEWEB)

Takahashi, H; Okuyama, M; Fujieda, H; Fujita, T; Iwasaki, A [National Aerospace Laboratory, Tokyo (Japan)

1994-11-01

The Quiet Short Take-Off and Landing (QSTOL) Experimental Aircraft `ASKA` has been researched and developed by the National Aerospace Laboratory (NAL). The `ASKA` was based upon the airframe of the home produced C-1 tactical transport which was modified into the Upper Surface Blowing (USB) -powered high- lift STOL aircraft. The wing configuration, however, was not changed. Therefore, this Experimental Aircraft does not always have the optimum configuration of a USB-type aircraft. So the authors tried to improve the aerodynamic characteristics of the STOL Aircraft. This paper describes the investigations which have been conducted to improve the aerodynamic characteristics of a subsonic jet transport semi-span model with an Upper Surface Blown Flap system which has been newly designed using the NAL STOL-CAD program. The model had an 8.2{degree} swept wing of aspect ratio 10.0 and four turbofan engines with short USB nozzles. The tests were conducted in the NAL 2{times}2m Gust Wind Tunnel with closed section and results were obtained for several flap and slat deflections at jet momentum coefficients from 0 to 1.85. Compared with the aerodynamic characteristics of the `ASKA` model, we determined that the airframe weight can be reduced and the aerodynamic characteristics can be improved significantly. 14 refs., 44 figs.

Experiment of exploration using the active-faults exploration system; Katsudanso tansa system wo mochiita chika tansa jikken

Energy Technology Data Exchange (ETDEWEB)

Mikada, H; Sato, H; Iwasaki, T; Hirata, N [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute; Ikeda, Y [The University of Tokyo, Tokyo (Japan). Faculty of Science; Ikawa, T; Kawabe, Y; Aoki, Y [JAPEX Geoscience Institute, Tokyo (Japan)

1996-10-01

A system for exploration of active-faults by seismic reflection profiling method was introduced at Earthquake Research Institute, University of Tokyo. A test-run was conducted to check the performance of this system at Ranzan, Saitama Prefecture. This paper describes the confirmed performance of mini-VIB as a wide band frequency seismic source, the quality of data obtained using a digital data acquisition system, and problems for data processing of fault exploration in the future. For the test-run at Ranzan, two-dimensional exploration was conducted by the quasi-three-dimensional data acquisition method using three geophones of 8 Hz, 28 Hz, and 40 Hz, simply arranged in parallel on the measurement line. Using an active seismic vibrator, mini-VIB, data acquisition of faults in the wide band frequency was achieved, which would result in the highly accurate imaging. Operation of data acquisition and processing systems is easy, and the system can be also used as a kind of black box. The existing methods are to be used sufficiently as a tool for imaging of faults. Further research for accumulating experience may become necessary toward the extension of the system expected in the future. 5 refs., 6 figs.

Glass Melting under microgravity. ; Space experiment by Mori astronaut. Mujuryokuka deno glass yoyu. ; Morisan no uchu jikken

Energy Technology Data Exchange (ETDEWEB)

Makihara, M. (Osaka National Research Institute, Osaka (Japan))

1993-03-01

A space experiment on glass melting under microgravity was performed in a space shuttle in September 1992. The experiment has been intended to make glass from glass material floating in air by heating and melting it with light and an acoustic levitation furnace. The acoustic levitation furnace used in the experiment has been arranged so that a sound wave from a speaker makes a steady wave in a cylindrical quartz glass core tube with a length of 16 cm and a diameter of 4 cm, and a test sample can be retained floating in a valley of central wave pressures. The test sample retained floating has been collected and heated by light from a 500-W halogen lamp. Behavior of molten glass liquid under microgravity has been investigated. The glass material powder spheres have been melted completely and made into glass without crystallization. With regard to flows generated in the test sample placed in the acoustic levitation furnace, a glass spot containing cobalt oxide has been attached onto part of the test sample surface for observation. As a result, the spot has been incorporated in the glass without developing diffusion. 6 refs., 4 figs.

Experimental study on axisymmetric air intake for the supersonic transport; choonsokukiyo jikutaishogata air intake no jikken kenkyu

Energy Technology Data Exchange (ETDEWEB)

Sato, T. [Institute of the Space and Astronautical Science,Tokyo (Japan); Takagi, I. [Kawasaki Heavy Industries, Ltd., Kobe (Japan); Kojima, T.; Kobayashi, H. [The University of Tokyo, Tokyo (Japan)

1998-12-05

Mixed-compression type axisymmetric air intakes for ATREX engine have been tested in the supersonic wind tunnel from Mach 0.5 to 4 since 1993. The throat area of the intake can be variable with a translating center spike to accomplish starting and off-design operation since the ATREX intake must work well over the wide flight Mach number up to 6. Here are presented effects of the intake design Mach number, the air bleed from a center spike and/or a cowl around the throat, an angle of attack and blunt nose of the spike on the intake performance characteristics, that is total pressure recovery and mass capture ratio. It is found that bleeding from the center spike and the cowl influences mainly on total pressure recovery and mass capture ratio respectively. The advantage of rounding properly off the spike nose is confirmed. Small center spike cone angle and/or blunt nose is sensitive to the angle of attack. (author)

Detection of buried pipes by polarimetric borehole radar; Polarimetric borehole radar ni yoru maisetsukan no kenshutsu jikken

Energy Technology Data Exchange (ETDEWEB)

Sato, M.; Niitsuma, H. [Tohoku University, Sendai (Japan); Nakauchi, T. [Osaka Gas Co. Ltd., Osaka (Japan)

1997-05-27

If the borehole radar is utilized for detection of buried pipes, the underground radar measurement becomes possible even in the situation where the mesurement on the earth surface is difficult, for example, such a place as under the road where there is much traffic. However, since buried pipes are horizontally installed and the existing borehole radar can send/receive only vertical polarization, the measurement conducted comes to be poor in efficiency from a viewpoint of the polarization utilization. Therefore, by introducing the polarimetric borehole radar to the detection of buried pipes, a basic experiment was conducted for the effective detection of horizontal buried pipes. Proposing the use of a slot antenna which can send/receive horizontal polarization in borehole in addition to a dipole antenna which sends/receives vertical polarization, developed was a step frequency type continuous wave radar of a network analyzer basis. As a result of the experiment, it was confirmed that reflection from buried pipes is largely dependent on polarization. Especially, it was found that in the slot dipole cross polarization mesurement, reflection from buried pipes can be emphasized. 4 refs., 5 figs.

3D seismic experiment in difficult area in Japan; Kokunai nanchiiki ni okeru sanjigen jishin tansa jikken

Energy Technology Data Exchange (ETDEWEB)

Minegishi, M; Nakagami, K; Tanaka, H [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

1997-05-27

Difficult area in this context means an exploration-difficult area supposed to store oil/gas but retarded in exploration for the lack of knowledge about the geological structure due to poor quality of available seismic survey records. Discussed in this paper is a survey conducted into an area covering the southern part of Noshiro-shi, Akita-ken, and Yamamoto-cho, Yamamoto-gun, Akita-ken. An area size suitable for data collection at a target depth of 2500m is determined using an interpretation structure compiled on the basis of available well data and 2D seismic survey data. The plan for siting shock points and receiving points is modified case by case as restrictive factors come to the surface (resulting from the complicated hilly terrain, presence of pipes for agricultural water, etc.). The peculiarities of seismic waves in the terrain are studied through the interpretation of the available well data and 2D seismic survey data for the construction of a 3D velocity model for the confirmation of the appropriateness of the plan for siting shock points and receiving points. Efforts are exerted through enhanced coordination with the contractor to acquire data so that a technologically best design may be won within the limits of the budget. The quality of the data obtained from this experiment is in general better than those obtained from previous experiments, yet many problems remain to be settled in future studies about exploration-difficult areas. 4 refs., 4 figs., 1 tab.

Numerical method to calculate flow-induced vibration in turbulent flow. 3rd Report. Analysis of vortex-induced vibration in an array of elastically supported tubes; Ranryuba ni okeru ryutai kozotai rensei shindo kaiseki shuho no kaihatsu. 3. Kangun ni okeru uzu reiki shindo kaiseki

Energy Technology Data Exchange (ETDEWEB)

Sadaoka, N.; Umegaki, K. [Hitachi, Ltd., Tokyo (Japan)

1996-01-25

A vortex-induced vibration of an array of elastically supported tubes is simulated in two-dimension by using a flow-induced vibration analysis program, which was developed in order to evaluate flow-induced vibration in various components such as heat exchangers. From a comparison of calculated results and experimental data, the following points are observed. (1) For the calculated results in a 5 {times} 5 square array, the flow pattern surrounding the first-row tubes is markedly different from that observed in the second-row or third-row tubes. This flow pattern is the same as that obtained from the experiment. (2) All tubes begin to oscillate due to unsteady fluid force and the oscillating mode is different for each row of tubes. These oscillation patterns show the same tendency in the experiments and it is concluded that the developed method can simulate vortex-induced vibration in an array of elastically supported tubes. 19 refs., 10 figs., 1 tab.

Experiment for 3-component S-wave reflection survey. Part 3; Sanseibun S ha hanshaho no kiso jikken. 3

Energy Technology Data Exchange (ETDEWEB)

Kano, N; Yamaguchi, K; Yokota, T; Kiguchi, T [Geological Survey of Japan, Tsukuba (Japan)

1996-10-01

Anisotropy has been investigated using S-wave as a technique for detecting fractures. In this study, fundamental experiments were carried out with slightly changing the measuring conditions at a place where anisotropy was expected. This paper describes the fundamental data acquisition of anisotropy analysis using S-wave, and a part of the results. The experiments were conducted on the agricultural road in Yamadera district, Matsuyama-machi, Yamagata Prefecture. Two flat unpaved roads meeting at right angles were used as traverse lines. In this place, several reflection surfaces were certainly detected by P-wave, and anisotropy of S-wave was confirmed from the velocity of refracted wave of S-wave. Data were processed for individual traverse lines meeting at right angles. Firstly, signal sweeping, correlation, and vertical superposition were made. Six kinds of data were prepared, i.e., three-component receiving records of data at 0{degree} of generating direction and three-component receiving records of data at 90{degree} of generating direction. Records of T-component at 0{degree} and R-component at 90{degree} were used for processing of the seismic reflection method. These records would be considered to be data of SH-wave and SV-wave, respectively. 4 figs.

Experiment for 3-component S-wave reflection survey. Part 3; Sanseibun S ha hanshaho no kiso jikken. 4

Energy Technology Data Exchange (ETDEWEB)

Kano, N; Kiguchi, T; Yamaguchi, K [Geological Survey of Japan, Tsukuba (Japan); Yokota, T [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

1997-10-22

Investigations and discussions were given by using P-S logging on anisotropy of refracted waves in the fundamental experiments conducted in the Matsuyama town, Yamagata Prefecture. In the investigations, S-wave was transmitted into two to three directions at four locations in total: one at the opening of a well with a depth of 100 m and three locations having offset of 50 m from the well opening, and anisotropy of direct waves in the depth direction was investigated. Data were recorded on the ground at the same time by using a 3-component receiver. As a result of the experiment, detection of the anisotropy by means of measurement inside the well was found more difficult than anticipated due to anomaly in the refracted waves, hence no clear velocity anisotropy has been observed. It appears that no azimuth anisotropy exists at depths shallower than at least 24 m. No anisotropy due to incident angles was made clear in the present experiment. Offset recording experienced poor S/N ratio, having made the data analysis difficult. The data for zero offset do not harmonize with the refracted wave analysis on the data derived by using the reflection method, whose cause requires further discussions. 4 figs., 2 tabs.

Studies on surface tension effect for free surface flow around floating models; Futai mokei mawari no jiyu hyomenryu ni oyobosu hyomen choryoku no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Suzuki, K [Yokohama National Univ., Yokohama (Japan). Faculty of Engineering; Akiba, H [Toyo Construction Co. Ltd., Tokyo (Japan)

1997-12-31

The effect of surface tension on free surface flow around floating models is discussed experimentally and numerically. Three-dimensional free surface flow around vertical circular cylinders floating in a circulating water channel was visually observed, where a surface-active agent was added to water. The results are analyzed using Weber number. The numerical analysis was done for vertical cylinder and CY100 models using the Rankine source method. Weber number of at least around 120 is necessary to eliminate the effect of surface tension from free surface flow around the CY100 model. The numerical analysis for the cylinder model needs simulation with wavelength shorter than that of free surface wave used by the Rankine source method. The model for the resistance test should be at least around 7m long to eliminate the effect of surface tension at Froude number of 0.1 or higher. 15 refs., 12 figs., 2 tabs.

Studies on surface tension effect for free surface flow around floating models; Futai mokei mawari no jiyu hyomenryu ni oyobosu hyomen choryoku no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Suzuki, K. [Yokohama National Univ., Yokohama (Japan). Faculty of Engineering; Akiba, H. [Toyo Construction Co. Ltd., Tokyo (Japan)

1996-12-31

The effect of surface tension on free surface flow around floating models is discussed experimentally and numerically. Three-dimensional free surface flow around vertical circular cylinders floating in a circulating water channel was visually observed, where a surface-active agent was added to water. The results are analyzed using Weber number. The numerical analysis was done for vertical cylinder and CY100 models using the Rankine source method. Weber number of at least around 120 is necessary to eliminate the effect of surface tension from free surface flow around the CY100 model. The numerical analysis for the cylinder model needs simulation with wavelength shorter than that of free surface wave used by the Rankine source method. The model for the resistance test should be at least around 7m long to eliminate the effect of surface tension at Froude number of 0.1 or higher. 15 refs., 12 figs., 2 tabs.

Experiment for buried pipes by stepped FM-CW radar; Step shiki FM-CW radar ni yoru maisetsukan tansa jikken

Energy Technology Data Exchange (ETDEWEB)

Suzuki, K.; Ito, M. [Kawasaki Geological Engineering, Co. Ltd., Tokyo (Japan); Tanabe, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1997-05-27

The underground radar exploration is adopted to surveys of cavity under the road and buried pipes since the result of high resolution is obtained. However, the explorative depth of the radar is shallow, 2-3m in soil basement, and its applicable field has been limited. The continuous wave radar (FM-CW radar) was devised to get deeper explorative depth, but has been used for the geological structure survey such as the fault survey since it is lower in resolution as compared with the pulse radar. Therefore, to make use of characteristics of the continuous wave radar and enhance resolution in the shallow part, an experiment on buried pipes was conducted for the purpose of assessing and improving the FM-CW radar. In this processing, the wave form treatment used in the reflection method seismic survey was adopted for the radar survey. There are some problems, but it is effective to adopt the same algorithm to that used in the seismic survey to the radar exploration. The explorative depth was discussed from the damping rate of electromagnetic waves and dynamic range of facilities of the experimental site, and 7m was obtained. 5 figs., 1 tab.

Loading test of pile affected by soil layer deformation; Jiban henkei no eikyo wo ukeru kui no saika jikken

Energy Technology Data Exchange (ETDEWEB)

Kakurai, M.; Tsuchiya, T. [Takenaka Corp., Osaka (Japan)

1997-10-10

Large soil tank developed for shearing experiments is used to study the horizontal movement of piles in earthquakes. The system comprises a soil filled (8m deep) tank, pile head loading jig, and 6 actuators. The soil tank is fabricated of 40 layers of 20cm-high iron frames of inner dimensions 2.5mtimes2.5m, and it is filled with soil that is to simulate the ground. The frames are divided into 4 groups each containing 10 frames, and the frames in each group are coupled with each other, so that all the frames in one group will move horizontally when the topmost frame in the group is moved horizontally. An actuator, which travels horizontally ganging with a computer, is mounted on the top frame in each group, and this setup enables the arbitrary simulation of ground deformation in the horizontal direction in an earthquake. The pile head loading jig, driven by 2 actuators, can keep restraining the pile head from rotation while applying load or deforming force to the pile head as desired in the vertical and horizontal direction. Experiments conducted using this system involve the force imposed on a pile in the soil tank by ground deformation and the resultant pile behavior including breakdown. 9 figs.

Experiments of cooling photovoltaic panel by desorption process; Dacchaku hanno wo riyoshita taiyoko hatsuden panel no ondo josho yokusei jikken

Energy Technology Data Exchange (ETDEWEB)

Akisawa, A; Inoue, S; Kashiwagi, T [Tokyo University of Agriculture and Technology, Tokyo (Japan)

1997-11-25

It is important to cool a photovoltaic (PV) panel, because increased panel temperature is accompanied by decreased power generation efficiency. The authors have proposed a PV power generation system combined with an adsorption chiller driven by low-temperature heat, and simulated temperature changes during the desorption cycle, where the chiller utilizes endothermic reactions of an adsorbent during the desorption cycle. Described herein are results of the tests carried out to validate possibility of controlling panel temperature increase. The system consists of the PV panel with which a bed packed with an adsorbent is monolithically combined, condenser and evaporator. It generates power during the daytime by sunbeams, and provides low-temperature heat during the nighttime by the evaporator. In particular, ice can be produced when methanol and activated coal are used as the adsorbate and adsorbent. It has an advantage of effective utilization of energy as the heat source, which has been merely dissipated by the conventional system in the air. Such a system is expected to be useful for promoting effective utilization of solar energy and for peak power shaving in summer. The initial targets are achieved by the tests. 4 refs., 10 figs.

Results of cultivation experiment at clean farm (vegetable plant). 1. Clean farm (yasai kojo) ni okeru saibai jikken kekka. 1

Energy Technology Data Exchange (ETDEWEB)

Miyaishi, T; Kawagishi, K; Matsuzaki, O; Nakahara, M [Kyushu Electric Power Co. Ltd., Fukuoka (Japan)

1991-03-31

This paper reports a summary of the facilities in an experimental plant constructed by the Kyushu Electric Power Company in 1988, and a result of experiments on cultivating salad and lettuce. The plant has environmentally controlled cultivating rooms of solar beam combined type and totally artificial light type, each having a floor area of 50 m {sup 2}, disposed with cultivating stages divided into three divisions of seedling culture, growth, and forced culture, nutritious liguid feeding devices of circulation type, and air conditioning equipment. The paper describes results of the tests aimed at realizing an increase in yield and profit, an optimum cultivating system, and economic facilities at the vegetable plant. Included in the tests are that (a) four kinds of salads and five kinds lettuce were selected for cultivation to decide most suitable kinds, based on literature survey and preliminary experiments; (b) varying the environmental conditions for the culture, such as temperature, radiating condition, concentration of the nutritious liquid, and concentration of carbon dioxide, conditions optimum or suitable for the plant growth were selected; (c) the plant was compared with glass green houses with respect to the required cultivating period of time, vitamin C content and color tones of the products; (d) the solar beam combined type room and the totally artificial light rooms were compared with respect to power consumption and heat capacity that passes through the cultivation room walls, and the latter was concluded being superior in economics and stability. 12 refs., 37 figs., 30 tabs.

Aerodynamics of the cable of cable-stayed bridges; Shachokyo cable no kuriki shindo tokusei no rikai to soreni motozuku kuriki seishinho no teian

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, M. [Kyoto University, Kyoto (Japan). Faculty of Engineering; Aoki, J.; Fuji, D. [West Japan Railway Company, Osaka (Japan); Kitayama, N. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Daito, Y. [Kyoto University, Kyoto (Japan)

1996-07-21

Wind tunnel tests were conducted assuming the aerodynamics of the cable of cable-stayed bridges especially in the case of strong wind with rain. Based on the results, an aerodynamic damping method was proposed. Factors of the rain vibration generation include the three-dimensional axial flow behind the cable, which is formed by the wind direction deviation angle, the upper side water flow on the cable surface formed by the rain, and the Karman vortex shedding, which are not uniform in the span direction. Newly proposed cable with elliptical plates showed an effective dumping performance. It restrains the formation of water flow due to its profile, and is effective for unstableness due to water flow formation. Distribution of the axial flow in the cable span direction was made clear. Three-dimensionality of the vortex shedding was greatly affected by this axial flow. Frequency of the Karman vortex shedding changed in the wide band by the axial flow. It was suggested that three-dimensionality of the flow field is enhanced by the rolling vibration, resulting in the unstableness of heaving vibration. 5 refs., 15 figs.

Effect of ventilated structure on dehumidification. ; Experimental result in winter. Tsuki koho no haishitsu koka ni kansuru kenkyu. ; Toki jikken kekka

Energy Technology Data Exchange (ETDEWEB)

Sugai, T; Ozaki, A [Fukuoka University, Fukuoka (Japan). Faculty of Engineering; Katayama, T; Hayashi, T; Shiotsuki, Y [Kyushu University, Fukuoka (Japan)

1912-09-01

Temperature and humidity characteristics and condensation within walls under heating and humidification were studied experimentally in winter using two test houses of conventional and ventilated structures. The absolute humidity in conventional one fluctuated depending on temperature gradient, water flux due to humidification and water adsorption onto glass wool, and accumulated water increased with humidification. That in ventilated one was also affected by dehumidification through ventilation layers. Under heating and humidification, the absolute humidity increased depending on temperature rise and water flux within walls. In conventional one, condensation was frequently observed on felt in walls and others because of accumulated humidity, while in ventilated one, humidity was kept lower within walls even under heating, because humidity in walls was discharged through ventilation layers. Condensation was also scarcely observed on waterproof moisture-permeable sheets in walls and others. 3 refs ., 39 figs 1., tab.

Study of seismic data acquisition using physical modeling system; Butsuri model jikken sochi wo mochiita data shutoku gijutsu ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Tsukui, R; Tsuru, T [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

1996-10-01

For the physical modeling system of Technology Research Center, Japan National Oil Corporation, data acquisition on the ocean and ground can be simulated using models. This system can provide data for verification of the data processing and elastic wave simulation algorithm. This can also provide data for decision of experiment specifications by making a model simulating the underground structure of the given test field. The model used for the physical modeling system is a gradient multilayer model with six-layer structure. Depth migration before stacking was conducted using data obtained through two acquisition methods, i.e., up-dip acquisition and down-dip acquisition. The depth migration before stacking was performed for data obtained by up-dip acquisition in addition to the records obtained by down-dip acquisition. Consequently, a definite reflection surface was observed, which has not been observed from the processing results of down-dip acquisition data. 9 figs.

Horn amplification at a tyre/road interface. Pt. 1. Experiment and computation; Tire/romenkan ni okeru horn koka. Jikken to keisan

Energy Technology Data Exchange (ETDEWEB)

Fujikawa, T. [Japan Automobile Research Institute Inc., Tsukuba (Japan)

2000-01-01

Tyre/road interface noise can be amplified by a horn type space formed by the tread face of the tyre and the road. This paper is a report on studies on experiment and computation to elucidate the above phenomenon in detail. Measurement and computation were carried out on a tyre replaced with a single cylinder, whereas it was verified that the horn effect by each frequency can be calculated by BEM computation. Then, discussions were given on actual tyres combined with the BEM computation, and the following results were acquired: (1) the horn effect is small in zones of low frequencies; (2) the larger the tread width, the larger the horn effect increases; (3) the relationship between the tread width and the horn effect is governed by the ratio of the road contact width to noise wavelength; (4) the frequency characteristics of the horn effect vary largely according to whether the sound source exists in forward or rearward locations; (5) the relationship between the forward and rearward locations of the sound source with the horn effect is governed by the distance between the front and rear ends of the road contact face of the tyre; (6) the smaller the radius of the tread shoulder, the greater the horn effect; (7) tread deformation due to load applied on the tyre slightly changes the frequency characteristics of the horn effect; (8) with the sound source existing closer to the center of ground contacting width, the horn effect increases; and (9) the present study has verified the horn effect of 22 dB as the maximum. If the sound source is not present at the center of ground contacting width, the horn effect is reduced to about 10 dB, but the value cannot be ignored as the influence on traffic noise. (translated by NEDO)

Study of seismic data acquisition using physical modeling system; Butsuri model jikken sochi wo mochiita data shutoku gijutsu ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Tsukui, R; Tsuru, T [Tech. Research Center, Japan National Oil Corp., Tokyo (Japan); Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

1996-05-01

The Physical Modeling System introduced into the Technology Research Center, Japan National Oil Corporation, and data collected by use of the system are presented. The Physical Modeling System is 10,000 times smaller than the real one, comprising a water tub section, measuring device section, and control section, etc. The water tub section comprises a tub for housing the model, transducers for transmitting and receiving vibration, controllers, etc. The water tub measures 1.8{times}1.2{times}0.9m. The model used in the experiment is an `inclined multilayer model` with each of its six layers pinching out toward the top, and is usable for the comparison of various migration methods. In one case in the records, reception was made at 184 reception points deployed at intervals of 3mm, when the minimum offset was 15mm and the maximum offset 564mm. Nothing very obvious was observed when the ordinary overlapping of DMO and CDP was applied to this record, which suggests that pre-overlapping migration treatment is required. 5 figs.

Analogue experiment of the crustal deformation by X-ray CT; X sen CT wo mochiita chikaku no henkei no analogue jikken

Energy Technology Data Exchange (ETDEWEB)

Nakajima, Y.; Shi, B; Murakami, Y. [Geological Survey of Japan, Tsukuba (Japan)

1997-05-27

This paper reports a predictive result on a deformation experiment on sand beds using an X-ray computerized tomography (CT) equipment. The X-ray CT is a method to perform the following processes: X-rays are irradiated on a sample; decayed intensity data are measured along ray paths of the permeated X-rays; the data are inverted by using the Fourier transform; and spatial distribution of the coefficient of X-ray absorption inside the sample is acquired as a gray scale image. The deformation experiment was carried by putting sand into an acrylic container to a depth of 2 cm and manually pressing a plate in the horizontal direction. Sand blocks make a relative motion along a specific plane when they are deformed, but it was not possible to recognize faults clearly by naked eyes. Upon completion of the deformation, the experimental device was placed on the CT equipment to acquire images of the two-dimensional cross section. The higher the X-ray absorption coefficient, the brighter the picture elements. It can be seen that three inversed faults have been imaged clearly. Therefore, this equipment was verified usable as an effective observation equipment for an analogue deformation experiment. 4 refs., 2 figs.

Vortex-induced vibrations of circular cylinder in cross flow at supercritical Reynolds numbers; Chorinkai Reynolds su ryoiki ni okeru enchu no uzu reiki shindo

Energy Technology Data Exchange (ETDEWEB)

Kawamura, T.; Nakao, T.; Takahashi, M.; Hayashi, M.; Goto, N. [Hitachi, Ltd., Tokyo (Japan)

1999-07-25

Vortex-induced vibrations were measured for a circular cylinder subjected to a water cross flow at supercritical Reynolds numbers for a wide range of reduced velocities. Turbulence intensities were changed from 1% to 13% in order to investigate the effect of the Strouhal number on the region of synchronization by symmetrical and Karman vortex shedding. The reduced damping of the test cylinder was about 0.1 in water. The surface roughness of the cylinder was a mirror-polished surface. Strouhal number decreased from about 0.48 to 0.29 with increasing turbulence intensity. Synchronized vibrations were observed even at supercritical Reynolds numbers where fluctuating fluid force was small. Reduced velocities at which drag and lift direction lock-in by Karman vortex shedding were initiated decreased with increasing Strouhal number. When Strouhal number was about 0.29, the self-excited vibration in drag direction by symmetrical vortex shedding began at which the frequency ratio of Karman vortex shedding frequency to the natural frequency of cylinder was 0.32. (author)

Wind-induced cable vibrations and countermeasures of cables of PC cable-stayed bridge. PC syachokyo keburu no kaze ni yoru shindo to sono taisaku

Energy Technology Data Exchange (ETDEWEB)

Yoneda, M. (Kawada Industries Inc., Tokyo (Japan))

1994-05-01

In recent years, long span of cable-stayed bridges is remarkable. The wind-induced cable vibration called as line vibration and wake galloping was given as an important problem not only in the steel cable-stayed bridges but also in the PC cable-stayed bridges. The technical engineers in design of the cable-stayed bridges have many times to confront the problems on the vibration control of cables, it is considered that sufficient understand of the wind-induced vibration and countermeasures for cables of the PC cable-stayed bridges is necessary. Many reports on the countermeasure examples and trend of vibration control centred on cables of the cable-stayed bridges have been published. In this paper, the wind-induced vibration of cables in the cable-stayed bridges was reviewed, the examples of countermeasures of vibration control on cables in the PC cable-stayed bridges was mainly introduced. The remaining tasks and future prospects on vibration control of the PC cable-stayed bridges were described. 14 refs., 13 figs., 4 tabs.

Field experiment for investigation of very shallow basement structure by micro-gravity survey; Microgravity tansa no gokusenbu kiban chosa eno tekiyo jikken

Energy Technology Data Exchange (ETDEWEB)

Oshita, K; Nozaki, K [OYO Corp., Tokyo (Japan)

1997-10-22

This paper illustrates the field experiment results in which micro-gravity survey was applied to investigation of very shallow basement structure between a few m and 10 m. Its applicability was discussed. In principle, the micro-gravity survey was conducted at the measuring points in a grid with 20 m pitch. Measuring points of 174 were used. The gravity system used for the measurements is an automatic gravimeter CG-3M made by the Scintrex. Survey results of P-wave reflection method conducted at the site using a vibrator focus were used as control data of micro-gravity survey. Consequently, change in the thickness of surface layer (earth filling) shallower than the depth of -10 m could be grasped as a plane. It was found that the micro-gravity survey is a useful method for the investigation of very shallow basement structure. Survey results by the reflection method could contribute to the determination of trend face at filtration and construction of density model as well as the geologic interpretation of gravity anomaly. As a result, reliability of micro-gravity survey and reflection method could be enhanced, mutually. 3 refs., 8 figs.

3D seismic experiment in the Minaminoshiro area, Akita. Data processing; Akitaken Minaminoshiro chiiki ni okeru sanjigen jishin tansa jikken. Data shori

Energy Technology Data Exchange (ETDEWEB)

Tanaka, H; Minegishi, M [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Nakagami, K [Japan Petroleum Exploration Co. Ltd., Tokyo (Japan)

1997-10-22

A 3D seismic experiment was carried out in the Minaminoshiro area in Akita Prefecture, an area difficult of performing seismic exploration. This paper reports progresses during data processing and future problems. The data processing has executed static correction of 3D refraction, 3D DMO correction, and an F-X prediction filter processing on the data in time domain in the 3D seismic exploration as acquired in a spread of 4 km times 5 km in the subject area. The result of the data processing verified existence of a folding structure and the Noshiro thrust fault groups in the east to west direction, and locations of the Sakagawa fault associated therewith. Seen particularly noticeably was a structure having a slope falling north-ward at 15 to 35 degrees in shallow and deep portions on the east side of the Sakagawa fault in the south to north direction. In addition, the Dogiri fault was identified, which has been though to exist in a direction crossing perpendicularly the Noshiro thrust fault groups. It is scheduled that spatial velocity will be analyzed, and data processing will be conducted for deep regions. 7 figs.

Analysis and model-tests on vortex-induced oscillation of bridges; Kyoryo no uzu reishin ni kansuru sanjigen oto kaiseki to fudo jikken

Energy Technology Data Exchange (ETDEWEB)

Yamamura, N. [Hitachi Zosen Corp., Osaka (Japan); Ogasawara, M. [Kansai Electric Power Co. Inc., Osaka (Japan); Shiraishi, N. [Maizuru College of Technology, Kyoto (Japan); Nanjo, M.

1996-07-21

In order to predict the three-dimensional response to vortex-induced oscillation of bridges, a model was investigated using the aerodynamic force coefficient including vortex-induced and self-excited forces, and the nonlinear response coefficient expressing constancy of response to vortex-induced oscillation. In the analysis, change of frequency in wind by the self-excited force, aerodynamic damping term, effect of the mode, and correlation of the vortex-induced force along member axis were taken into account. The aerodynamic force and nonlinear response coefficients were identified from the homogeneous and turbulent flow results of wind tunnel tests using a two-dimensional spring support rigid body model with varied damping factor. The aerodynamic damping term can be estimated from the nonlinear aerodynamic force coefficient, but it was enough to calculate it from the quasi-stationary coefficient in general bridge profiles. The correlation of the vortex-induced force was obtained from measurements of the vertical variation components of trailing flow under the resonance state, or the pressure distribution of the member surface. When comparing to the wind tunnel test of three-dimensional model of cable-stayed bridge, the response amplitude by the present analysis method was consistent well with the test results rather than by the method in which the amplitude of two-dimensional model was corrected. 10 refs., 4 figs., 3 tabs.

Combustion-driven oscillation in a furnace with multispud-type gas burners. 4th Report. Effects of position of secondary air guide sleeve and openness of secondary air guide vane on combustion oscillation condition; Multispud gata gas turner ni okeru nensho shindo. 4. Nijigen kuki sleeve ichi oyobi nijigen kuki vane kaido no shindo reiki ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Akiyama, I.; Okiura, K.; Baba, A.; Orimoto, M. [Babcock-Hitachi K.K., Tokyo (Japan)

1994-07-25

Effects of the position of a secondary air guide sleeve and the openness of a secondary air guide vane on combustion oscillation conditions were studied experimentally for multispud-type gas burners. Pressure fluctuation in furnaces was analyzed with the previously reported resonance factor which was proposed as an index to represent the degree of combustion oscillation. As a result, the combustion oscillation region was largely affected by both position of a guide sleeve and openness of a guide vane. As the openness having large effect on the ratio of primary and secondary air/tertiary air and the position hardly having effect on the ratio were adjusted skillfully, the burner with no combustion oscillation region was achieved in its normal operation range. In addition, as the effect of preheating combustion air was arranged with a standard flow rate or mass flow flux of air, it was suggested the combustion oscillation region due to preheating can be described with the same manner as that due to no preheating. 5 refs., 8 figs.

Experimental study of high-speed counter-rotation propeller on low speed wind range; Dojiku hantengata kosoku propeller no teisokuiki ni okeru fudo jikken

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Collaborative research was conducted by National Aerospace Laboratory and Japan Aircraft Development Company in the period of fiscal 1988-1992 into methods for testing aircraft with advanced propeller in low-speed wind tunnel. The propulsion efficiency of the currently available high-bypass turbofan engine is approximately 60% in the vicinity of Mach number 0.85. Propeller-driven aircraft, whose propulsion efficiency is as high as 80% in the low Mach number domain, are scarcely in practical use in the domain of Mach number 0.75 or higher. There are studies reported abroad as well as in Japan for the propeller-driven aircraft to enjoy higher propeller propulsion efficiency even in the vicinity of Mach number 0.8 by modifying the propeller diameter, number of blades, and blade sections, etc. This paper describes the experimental research into the high-speed counter-rotation propeller. A counter-rotation propeller 0.3m in diameter and provided with coaxially arranged 8times2 SR-2 blades is evaluated for pitch angles during the takeoff and landing modes, for thrust characteristics at the pitch angle for the cruising mode, and for propeller backwash and noise. 15 refs., 72 figs., 9 tabs.

Study on the behavior of reaction disk in the vacuum brake booster; Shinkushiki bairyoku sochi ni okeru reaction disk no kyodo kaiseki jikken

Energy Technology Data Exchange (ETDEWEB)

Kuroda, M; Sawada, T; Kato, Y [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan); Ogawa, E; Nakamura, S [Jidosha Kiki Co. Ltd., Tokyo (Japan)

1997-10-01

Vacuum brake booster has been widely applied in automobiles, and it needs much time for experiments in order to design a new type model and so on. In this report concentrating on the behavior of a reaction disc, it was simulated by ARAQUS FEM program where coefficients of rubber disc are Mooney-Rivlin constants. It was shown that the numerical results represent good agreement with experiments, and in addition that values of jumping force which shows the starting point of the brake increases with the increment of the hardness of the disc, clearance and so on. 2 refs., 10 figs.

Depth imaging system for seismic reflection data. Part 1. Outline of system; Hanshaho jishin tansa data no tame no shindo imaging system. 1. System no gaiyo

Energy Technology Data Exchange (ETDEWEB)

Shimizu, N [Japex Jeoscience Institute, Tokyo (Japan); Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Tsuru, T [Japan National Oil Corp., Tokyo (Japan)

1996-10-01

Structures of oil and gas fields to be recently explored have changed from simple structures represented by anticline into more complicated and more delicate structures in the deeper underground. In order to discover and develop prospective oil and gas fields among such geological structures, it is indispensable to construct a system which can treat seismic exploration date collectively before stacking and can easily perform imaging of underground structures accurately. Based on the advancement of hardware, Japan National Oil Corporation and Japan Petroleum Exploration Co., Ltd. have developed a depth imaging system as an interactive tool for constructing underground structures accurately through a cooperation of highly accurate imaging technology. Using this system, two-dimensional underground structure models can be easily given and modified by interactively referring to results of depth migration velocity analysis and stacking velocity analysis, well data, cross sections after depth transform, etc. 1 fig.

Research on a new rubber's absorber system for cable-stayed bridges. PC shachokyoyo shazai teichakubu shindo kyushuyo boshin gomu no shinkiko ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Oikawa, K.; Kibe, H.; Ohashi, W. (SE Corp., Tokyo (Japan))

1993-09-30

Cable-stayed bridges are being constructed increasingly and their maximum effective span length is becoming longer to the extent that it is about to reach the limit, thereby diagonal members which, by nature, tend to vibrate become much longer, hence problems concerning vibration have drawn attention. In this article, regarding vibration insulating rubber for absorbing vibrations to be set at an anchorage of diagonal members, a new mechanism has been invented and its analysis as well as demonstration experiment have been conducted. This mechanism is based on the concept that the vibration insulating rubber has been set beforehand at the time of installing the diagonal members, adheres to the diagonal members immediately after the diagonal members are stretched, but its adherence is released simply when tension adjustment is needed, and the spring constant of the rubber can be calculated simply within the range of practical use. The results obtained from the above analysis and demonstration experiment are as follows; it is necessary to set vibration insulating rubber in the vicinity of the anchorage of diagonal members in order to absorb vibrations of the members and the method to make its setting simple and secure has been confirmed. Also the calculation method of spring constant of vibration insulating rubber necessary for estimating the secondary bending stress of diagonal member has been confirmed, thereby designing of vibration insulating rubber has become easy. 8 refs., 14 figs., 2 tabs.

Creep analysis and torsional vibration analysis of cable-stayed bridges with two edge composite girders; Nishuketa gosei kozo shachokyo no creep kaiseki to nejiri shindo kaiseki

Energy Technology Data Exchange (ETDEWEB)

Hoshino, M. [Nihon University, Tokyo (Japan). College of Science and Technology

1996-07-21

This paper describes the creep analysis and torsional vibration analysis of cable-stayed bridges with two edge composite girders. The girder is composed of the concrete slab and the steel girder. I-girders are placed at both edges of the profile. Such a type of bridge was investigated. As the stress migrates by the creep of concrete slab, it is necessary to evaluate the influence of this creep precisely in designing. In the analysis, the composite girder was expressed not by the single member, but by the binary member consisting of concrete member and steel member. Two methods were employed, i.e., method A in which both members are connected by the rigid body beam and method B in which the profile of concrete is converted into the profile of steel. The method A provided better accuracy, but the method B was often sufficient. Torsional rigidity of the open profile structure was much smaller than that of the box profile. As the torsional natural frequency was low, proper torsional vibration analysis was indispensable especially from the viewpoint of wind resistance. Two methods were employed, which utilize the vibration analysis method for general space frame structures. Results of both methods were agreed mutually, but the second method provided better calculation efficiency. 10 refs., 9 figs., 6 tabs.

On the hydroelastic response of box-shaped floating structure with shallow draft. Tank test with large scale model; Senkitsusui hakogata futai no harochu dansei oto ni tsuite. Ogata mokei ni yoru suiso shiken

Energy Technology Data Exchange (ETDEWEB)

Yago, K; Endo, H [Ship Research Inst., Tokyo (Japan)

1997-12-31

The hydroelastic response test was carried out in waves using an approximately 10m long large model, and the numerical analysis was done by the direct method, for a commercial-size (300m long) box-shaped floating structure with shallow draft. The scale ratio of the model is 1/30.8, and the minimum wave cycle is around 0.7s from wave-making capacity of the tank, which corresponds to 4 to 14s with the commercial-size structure. Elastic displacement and bending strain were measured. The calculated results by the direct method are in good agreement with the observed results. The fluid dynamic mutual interference effects between elements are weak in added mass but strong in damping force, indicating that the range of mutual interference is strongly related to rolling cycle in the range of mutual interference. Wave pressure on the floating structure bottom is high at the upper side of the wave, greatly damping towards the downside of the wave. However, response amplitude of elastic displacement tends to increase at the ends, both in upside and downside of the wave. For the floating structure studied, the 0 to 4th mode components are predominant in longitudinal waves, and the 6th or higher mode components are negligibly low. 21 refs., 15 figs., 2 tabs.

On the hydroelastic response of box-shaped floating structure with shallow draft. Tank test with large scale model; Senkitsusui hakogata futai no harochu dansei oto ni tsuite. Ogata mokei ni yoru suiso shiken

Energy Technology Data Exchange (ETDEWEB)

Yago, K.; Endo, H. [Ship Research Inst., Tokyo (Japan)

1996-12-31

The hydroelastic response test was carried out in waves using an approximately 10m long large model, and the numerical analysis was done by the direct method, for a commercial-size (300m long) box-shaped floating structure with shallow draft. The scale ratio of the model is 1/30.8, and the minimum wave cycle is around 0.7s from wave-making capacity of the tank, which corresponds to 4 to 14s with the commercial-size structure. Elastic displacement and bending strain were measured. The calculated results by the direct method are in good agreement with the observed results. The fluid dynamic mutual interference effects between elements are weak in added mass but strong in damping force, indicating that the range of mutual interference is strongly related to rolling cycle in the range of mutual interference. Wave pressure on the floating structure bottom is high at the upper side of the wave, greatly damping towards the downside of the wave. However, response amplitude of elastic displacement tends to increase at the ends, both in upside and downside of the wave. For the floating structure studied, the 0 to 4th mode components are predominant in longitudinal waves, and the 6th or higher mode components are negligibly low. 21 refs., 15 figs., 2 tabs.

Automobile simulation model and its identification. Behavior measuring by image processing; Jidosha simulation model to dotei jikken. Gazo kaiseki ni yoru undo no keisoku

Energy Technology Data Exchange (ETDEWEB)

Suzuki, H; Morita, S; Matsuura, Y [Osaka Sangyo University, Osaka (Japan)

1997-10-01

Model simulation technology is important for automobiles development. Especially, for the investigations concerning to ABS, TRC, VDC, and so on, the model should be the one which can simulates not only whole behaviors of the automobile, but also such internal information as torque, acceleration, and, velocity of each drive shafts, etc.. From this point of view, 4-wheels simulation model which can simulates almost over 50 items, was made. On the other hand, technique of 3-D image processing using 2 video cameras was adopted to identify the model. Considerably good coincidences were recognized between the simulated values and measured ones. 3 refs., 7 figs., 2 tabs.

Energy-based damping evaluation of cable-stayed bridges and its application to Tsurumi Tsubasa bridge; Shachokyo shindo gensui no energy teki hyokaho to Tsurumi Tsubasakyo eno tekiyo

Energy Technology Data Exchange (ETDEWEB)

Yamaguchi, H. [Saitama University, Saitama (Japan). Faculty of Engineering; Takano, H.; Ogasawara, M.; Shimosato, T. [Metropolitan Expressway Public Corp., Tokyo (Japan); Kato, M.; Kato, H. [NKK Corp., Tokyo (Japan)

1996-07-21

This paper provides and discusses a more common energy-based evaluation method of vibration damping in cable-stayed bridges. This method was applied to data obtained from the field vibration test of the Tsurumi Tsubasa Bridge. The damping was defined as dissipation energy in one cycle against the total potential energy. The dissipation energy from shoe friction, aerodynamic damping, and dampers for cables was added to the method proposed by Yamaguchi, et. al., in which the energy of girders, towers, and cables were quantitated, and the dissipation energy was determined from the loss factor of each constituent, to evaluate the damping of whole bridge. Thus, a more common energy-based evaluation method was provided. This method was applied to the damping obtained from the field vibration test of Tsurumi Tsubasa Bridge. Consequently, it was found that the damping of whole bridge was significantly affected by the shoe friction, aerodynamic damping, and dampers for cables. Distinguished damping characteristics of the Tsurumi Tsubasa Bridge could be explained by the energy-based evaluation. Validity of the energy-based evaluation method for damping of cable-stayed bridges was demonstrated. 15 refs., 9 figs., 6 tabs.

Analysis of vibration characteristics of a prestressed concrete cable-stayed bridge using strong motion observation data. Jishin kansoku ni motozuku PC shachokyo no shindo tokusei no kaiseki

Energy Technology Data Exchange (ETDEWEB)

Inatomi, T. (Port and Harbour Research Institute, Kanagawa (Japan)); Takeda, T.; Obi, N.; Yamanobe, S. (Kajima Corp., Tokyo (Japan))

1994-05-31

Records of seismic observation were analyzed for the purpose of proving the validity of antiseismic design for a prestressed concrete (PC) cable-stayed bridge. This bridge is a three span continuous PC cable-stayed bridge of 498 m in bridge length, and is constructed on alluvial soft ground. The seismometer used is a servo type accelerometer. The observed frequency and mode of seismic vibration are in good agreement with those in the analysis and hence the validity of modelling of the structure in designing was confirmed. It was also confirmed that the bending vibration and torsional vibration of the main girder are separated as designed. However, some points such as a large difference in the observed vibration and analysed vibration in the mode accompanying rotation of the base are listed as problems to be solved in antiseismic design. In order to investigate the attenuation constant of the upper structure, a seismic wave response analysis was performed and its results were compared with observed ones. When the attenuation constant is assumed to be 2%, agreement of data between analysis and observation is good, and it is considered that the attenuation constant of the upper structure only without the effects of attenuation of energy escape from the base and crack generation in concrete was about 2% in the observed earthquake (maximum acceleration on the ground: 51 Gal). 8 refs., 9 figs., 2 tabs.

Model experiments on imaging subsurface fracture permeability by pulsed Doppler borehole televiewer; Pulse doppler borehole televiewer ni yoru kiretsu tosuisei hyoka ni kansuru model jikken

Energy Technology Data Exchange (ETDEWEB)

Inagaki, Y; Niitsuma, H [Tohoku University, Sendai (Japan). Faculty of Engineering

1996-05-01

This paper reports model experiments to evaluate flow rates of fluids passing through a fracture by using a Doppler borehole televiewer (DBHTV). A supersonic transducer disposed on a well axis transmits transmission pulses, and a transducer receives scattered waves generated by particulates in water and waves reflected on a well wall. This signal is applied with time gating to extract only the scattered waves from particulates in the vicinity of the well wall. Deriving spectra in the recorded Doppler signal obtains flow velocity components in the direction of the well radius. A model was made with a polyvinylchloride pipe with a diameter of 14.6 cm to simulate a well, to which an aluminum pipe with an inner diameter of 2 mm is connected to be used as a simulated fracture, and mud water is circulated in the pipe. The result of deriving a passed flow volume in this model by integrating flow rate distribution derived by using the above method to a predetermined range in the vicinity of the fracture showed a good proportional relationship with actual flow rate in the simulated fracture. 1 ref., 7 figs.

Experiments on transition process of laminar separation bubble on airfoils. Yokukeijo ni shozuru soryu hakuri ho naibu no sen prime i katei ni tsuiteno jikken

Energy Technology Data Exchange (ETDEWEB)

Rinoie, K [National Aerospace Lab., Tokyo (Japan); Sato, J [The Univ. of Tokyo., Tokyo (Japan). Faculty of Engineering

1990-07-05

Experiments have been done to investigate the transition process of the laminar separation bubble on airfoils. Measurements of the power spectrum density distribution of the streamwise velocity fluctuation was made. Three airfoils which have different steplike pressure distributions were used for measurements. A discrete spectrum and its sub and higher harmonics were observed. The frequeny of the discrete spectrum was in good agreement with that predicted by the linear stability theory of the separated free shear layer. From results, it is concluded that the velocity disturbance observed initially in the amnner separation bubble for the three airfoils shows similar characteristic to that in the separeted free shear layer. For the airfoil whose design pressure recovery is minimum among three airfoils, however, another kind of the discrete spectrum was also observed. This is interpreted to be caused by the interference with the external cyclic disturbance. 11 refs., 11 figs.

Relation between peak period of microtremor spectral ratio (horizontal and vertical components) and basement depth; Bido no suiheido/jogedo supekutoru hi no peak to kiso shindo tono kankei

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, H; Mizutani, K; Saito, T [Iwate University, Iwate (Japan). Faculty of Engineering

1996-05-01

The peak period of the horizontal/vertical spectral ratio of microtremors was referred to the underground structure for the purpose of finding out if it was possible to estimate the ground structure by use of the peak period of the spectral ratio. The observation was carried in the areas of Morioka City and Hachinohe City using seismographs for measuring east-west, north-south, and up-down motions. As for the relationship between the peak period of the spectral ratio distribution involving 490 observation sites and the known gravity anomalies in the Morioka City area, it was found that the peak period of the spectral ratio tended to be shorter from west toward east while the gravity anomalies were greater from west toward east. Again, as for the relations with the underground geology, the period was longer when the distance to the granite basement was greater, and shorter when smaller. In the Hachinohe City area, relations not only of the first period peak but also of the second period peak to the basement were disclosed, which indicates the possibility that the peak period of the spectral ratio will be used as a means for estimating the basement structure. 2 refs., 8 figs.

Velocity profiles of acoustic streaming in resulting stokes layer by acoustic standing wave in a duct; Kannai kichi shindo ni okeru stokes sonai onkyoryu ryusoku bunpu no kaiseki

Energy Technology Data Exchange (ETDEWEB)

Arakawa, M; Kawahashi, M [Saitama University, Saitama (Japan). Faculty of Engineering

1995-07-25

Acoustic streaming is generated by Reynolds stress in the sense of mean acoustic momentum flux in a sound field. In the case of an acoustic standing wave produced by an air column oscillation in a closed duct, the friction and the Reynolds stress in the resulting Stokes layer are the essentials of acoustic streaming generation in the vicinity of the duct wall. The thickness of the Stokes layer decreases with the oscillatory Reynolds number. The plane wave propagation in the duct is assumed for the case of high Reynolds number except for the thin Stokes layer adjacent to the duct wall. The velocity profiles of the streaming are estimated theoretically from the steady component of the second-order term of a perturbation expansion in which the first-order approximation is a sinusoidal oscillation of the air column with plane waves. The present paper describes theoretical analysis of the velocity profiles of the acoustic streaming in the Stokes layer by means of the matched asymptotic expansion method. The results obtained show the existence of reverse streaming in a very thin layer adjacent to the wall and the effects of thermal boundary conditions at the wall on the velocity profiles of acoustic streaming in the Stokes layer. 9 refs., 8 figs.

Laboratory study on streaming potential for exploring underground water flow; Shitsunai jikken ni yoru ryudo den`i wo mochiita mizu michi tansa no kanosei no kento

Energy Technology Data Exchange (ETDEWEB)

Sato, H; Shima, H [Oyo Corp., Tokyo (Japan)

1997-05-27

To investigate a possibility of exploration of underground water flow as well as to grasp the underground fluid flow by measuring streaming potential at the ground surface, some experiments were conducted using a model unit by considering the difference of permeability. For this experimental unit, water is driven by adding head difference between the polyethylene vessel filled with water and the experimental water tank. The size of water tank is 350{times}160 mm with a height of 160 mm. Twenty platinum electrodes are set on the cover of water tank. Toyoura standard sand and Kanto loam were used for the experiments. For the experiments, fluid was injected in various combined models by considering the permeability, to measure the streaming potential. As a result, it was explained by the streaming potential that the fluid flows in a form of laminar flow in the experimental water tank, and that the movement of fluid in the Kanto loam is quite slow. It was also confirmed that the streaming potential method is an effective technique for grasping the movement of fluid. 3 refs., 8 figs.

Laboratory investigation on streaming potential for sandy soil and weathered rock; Shitsunai jikken ni yoru sashitsu jiban oyobi fuka ganban no ryudo den`i no kento

Energy Technology Data Exchange (ETDEWEB)

Sato, H; Shima, H [OYO Corp., Tokyo (Japan)

1996-10-01

Laboratory experiment on sandy soil and weathered rock was conducted to clarify the generation mechanism of streaming potential due to underground fluid. Streaming potential is caused by underground fluid flow, namely by fluid flow in porous substances as electrokinetic phenomenon. In experiment, Inagi sand, Toyoura sand and strongly decomposed weathered granite were used. In Inagi and Toyoura sands, positive streaming potential was observed downstream in fluid flow. Streaming potential could be nearly determined as primary function of fluid velocity, and generated streaming potential increased with fluid resistivity. Streaming potential was higher in Inagi sand than Toyoura sand, probably depending on hydraulic radius, size of bleeding channel, and conductivity of sand surface. In weathered granite, negative streaming potential was measured. In the case of positive {zeta} potential, negative streaming potential is theoretically generated downstream in fluid flow. This experiment suggested possible generation of negative streaming potential in some kinds of ground. 2 refs., 6 figs., 1 tab.

Reduction of belt CVT gear noise by gear train modification. Optimize vibration characteristics of gear train; Belt CVT no gear noise teigen gijutsu. Gear train shindo tokusei no saitekika

Energy Technology Data Exchange (ETDEWEB)

Arimatsu, M; Kawakami, T [Nissan Motor Co. Ltd., Tokyo (Japan)

1997-10-01

With the reduction of vehicle noise, the requirements for an efficient method to reduce transmission gear noise have become stronger yearly. So far efforts to reduce gear noise have generally focused on ways of improving the gears themselves. In addition to these traditional methods, it proved very beneficial to us to optimize the gear train structure. Nissan has just released the new Belt CVT for 2.0L Front wheel drive vehicles. We have been analyzing vibration of the gear train by using a finite element model since the early development stage, and we could achieve the quiet gears effectively. 2 refs., 9 figs.

Study on the characteristics of earthquake ground motion in the Hanshin area based on microtremor measurements; Bido kansoku ni motozuku Hanshin chiiki no jiban shindo tokusei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Suzuki, H; Seo, K; Yamanaka, H [Tokyo Institute of Technology, Tokyo (Japan)

1997-05-27

The Hyogoken-nanbu earthquake in 1995 was a local earthquake that has hit directly a large urban area, having caused damages the greatest since the War mainly in the city of Kobe. The present study has noticed the areas of Sumiyoshi, Nada Ward, Kobe City and Nanbu, Nishinomiya City where damages show different distribution; elucidated the characteristics of earthquake ground motion based on microtremor measurements; and discussed the relation thereof with the earthquake damage distribution. It was verified that microtremors and seismic motions are in rough agreement in the Sumiyoshi area, by comparing and discussing the spectrum ratio between the microtremors and the seismic motions. No correspondence was recognized in the Sumiyoshi area between distribution of the average microtremor spectrum ratio with cycles of 0.2 to 0.8 second and distribution of damages caused by the Hyogoken-nanbu earthquake. The ground characteristics evaluation alone is insufficient to explain distribution of the damages in a relatively wide range in the city of Nishinomiya, for which effects of distance decay should be taken into consideration. 6 refs., 7 figs.

Application of magnetotelluric method to hydrocarbon exploration in the Yurihara oil and gas field, northeast Japan; Akitaken Yurihara gasu den ni okeru MT ho jikken chosa. 2

Energy Technology Data Exchange (ETDEWEB)

Mitsuhata, Y [Geological Survey of Japan, Tsukuba (Japan); Matsuo, K; Minegishi, M [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

1997-10-22

Experiment and investigation are conducted in the Yurihara District, Akita Prefecture, to verify that the magnetotelluric (MT) method can be effectively applied to oil and gas fields. In the Yurihara district there exist a number of pits dug for exploration or production, and records on seismic surveys conducted, and therefore the geological structure of this district can be explained fairly well. The oil and gas reservoirs belong in the Nishikurosawa stratum overlain by the Onagawa stratum and Funakawa stratum. The Nishikurosawa rocks, basaltic rocks for example, present a resistivity of approximately 5 ohm/m which is higher than that of the other two that is more or less 1 ohm/m. Under the circumstances, experiment and investigation are conducted so as to detect the Nishikurosawa basaltic rocks as a high-resistivity stratum located under low-resistivity strata by use of the MT method. As the result, a high-resistivity stratum corresponding to the Nishikurosawa basaltic stratum is detected under low-resistivity strata, and the three-dimensional structure of the basaltic stratum is disclosed. In this stratum, the resistivity value gradually increases from south toward north with occasional abrupt rises, and it is found that such abrupt rises result from oil and gas producing strata where exploitation is under way. 5 refs., 6 figs.

Polarimetric borehole radar measurement near Nojima fault and its application to subsurface crack characterization; Polarimetric borehole radar ni yoru Nojima danso shuhen no chika kiretsu keisoku jikken

Energy Technology Data Exchange (ETDEWEB)

Sato, M.; Taniguchi, Y.; Miwa, T.; Niitsuma, H. [Tohoku University, Sendai (Japan); Ikeda, R. [National Research Institute for Disaster Prevention, Tsukuba (Japan); Makino, K. [Geophysical Surveying and Consulting Co. Ltd., Tokyo (Japan)

1997-05-27

Practical application of subsurface crack characterization by the borehole radar measurement to which the radar polarimetric method was introduced was attempted to measuring objects for which the borehole radar has not been much used, for example, the inside of low loss rock mass or fracture zone where cracks tightly exist. A system was trially manufactured which makes the radar polarimetric measurement possible in the borehole at a 1000m depth and with a about 10cm diameter, and a field experiment was conducted for realizing the subsurface crack characterization near the Nojima fault. For the measuring experiment by the polarimetric borehole radar, used were Iwaya borehole and Hirabayashi borehole drilled in the north of Awaji-shima, Hyogo-ken. In a comparison of both polarization systems of Hirabayashi borehole, reflected waves at depths of 1038m and 1047m are relatively stronger in both polarization systems than those with the same polarization form and at different depths, whereas reflected waves around a 1017m depth are strong only as to the parallel polarization system. Characteristics of the polarization in this experiment indirectly reflect crack structures. 6 refs., 6 figs., 1 tab.

Leveling of battery load and extension of battery life by serial connection of electric double layer capacitors with batteries for electric vehicles. Experimental results on the small model; Denki jidoshayo denchi to denki nijuso capacitor no chokuretsu setsuzoku ni yoru denchi futan no heijunka oyobi denchijumyo no enshinka. (kogata model ni yoru jikken seika). Kogata model ni yoru jikken seika

Energy Technology Data Exchange (ETDEWEB)

Takehara, J.; Okubo, N.; Miyaoka, K. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

1996-10-25

The load leveling method of batteries for electric vehicles was studied for extension of a battery life and mileage every charging. Under large load fluctuation conditions such as deceleration and acceleration, use of electric power sources other than battery for peek load at acceleration can improve a battery life, output power capacity and mileage every charging. Combination of effective recovery of regenerative power at deceleration with its discharge at acceleration is one of the effective methods. The electric double layer capacitors are serially connected with the batteries, regenerative power is charged only into the capacitors, and both voltages of the battery and capacitor are applied to a power circuit. Battery load is reduced by load on the capacitor. Until the capacitor is re-charged by regenerative power after full discharge, power is supplied only by battery through a diode. Capacitor power is used as effectively as possible until approaching considerably low voltage. As peak load of the battery is reduced by 30%, the mileage increases by 5.7%, and the battery cycle life becomes 1.5 times longer. 7 refs., 5 figs., 3 tabs.

Double linearization theory applied to three-dimensional cascades oscillating under supersonic axial flow condition. Choonsoku jikuryu sokudo de sadosuru sanjigen shindo yokuretsu no niju senkei riron ni yoru hiteijo kukiryoku kaiseki

Energy Technology Data Exchange (ETDEWEB)

Toshimitsu, K; Nanba, M [Kgushu University, Fukuoka (Japan). Faculty of Engineering; Iwai, S [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

1993-11-25

In order to examine the aerodynamic characteristics of a supersonic axial flow turbofan realizing flight of Mach number of 2-5, the double linearization theory was applied to a three dimensional oscillation cascade accompanying a steady load in a supersonic axial flow condition and unsteady pneumatic force and aerodynamic unstability of oscillation were studied. Moreover, the values based on the strip theory and the three-dimensional theory were comparatively evaluated. Fundamental assumptions were such that the order of steady and unsteady perturbation satisfies the holding condition of the double linearization thory in a supersonic-and equi-entropy flow of non-viscous perfect gas. The numerical calculation assumed parabolic distributions of camber and thickness in the blade shape. As a result, the strip theory prediction agreed well with the value given by the three-dimensional theory in the steady blade-plane pressure difference and in the work of an unsteady pneumatic force, showing its validity. Among the steady load components of angle of attack, camber and thickness, the component of camber whose absolute value is large has the strongest effect on the total work. The distribution reduced in the angle of attack and camber from hub toward tip gives a large and stable flutter margin. 5 refs., 13 figs., 2 tabs.

Optimization of dynamic source depth for seismic surveys. Part 7; Dynamite shingen no hasshin shindo no saitekika ni tsuite (hyoso kozo no suitei (kusssetsuho jishin tansa oyobi denki denjiho tansa)). 7

Energy Technology Data Exchange (ETDEWEB)

Tanaka, H; Murayama, R; Mitsuhata, Y; Ishikawa, H [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

1996-05-01

For the improvement of quality of data collected by reflection aided seismic exploration using dynamite as the seismic source, information has to be collected about the surface layer structure before the charge depth is determined. For this purpose, refraction, electric, and electromagnetic exploration methods were tried. In the refraction method, an impactor was used as the seismic source. In the records, the surface wave prevails because vibration was generated on the surface. Analysis was made by the use of the initial travel time tomography. In the electric exploration, a double pole array was used to measure resistivity. The measured data was subjected to a fully automatic inversion for analysis. As the result, it was disclosed that it was useful to know the deep-level structure directly by use of tomographic methods in refraction seismic exploration so as to find the optimum charge level. Furthermore, about the electric and electromagnetic exploration techniques, it was found that these methods can be applied making use of resistivity to the evaluation of groundwater saturation. 7 refs., 5 figs., 3 tabs.

Vibration characteristics and dynamic increment factor of 2 span continuous PC cable-stayed bridge under moving vehicles; 2 keikan renzoku PC shachokyo no sharyo sokoji no shindo tokusei to doteki zofukuritsu

Energy Technology Data Exchange (ETDEWEB)

Fukada, S.; Kajikawa, Y. [Kanazawa Univ. (Japan)] Tsunomoto, M. [Oriental Construction Co. Ltd., Tokyo (Japan)

1998-10-21

In this study, experiments on and simulation analyses of the travels of vehicles on a 2 span continuous PC cable-stayed bridge were conducted, and the propriety of the analysis method, vibration characteristics of traveling vehicles, and characteristics of the effective amplitude and dynamic increment factor concerning various traveling states were discussed. The results show that actually measured value of strain to a dynamic load substantially agreed with the value of strain obtained in the case of analysis in which the end fulcrums were movable. The actually measured value of natural frequency was between the value of natural frequency in the case of analysis in which the end fulcrums were movable and the value in the case of analysis in which the end fulcrums were in a pin state. The actually measured value of mode damping constant agreed exactly with the value of mode damping constant calculated on the assumption that the damping constant of the main beam is 1.0%, those of the main tower and bridge pier 5.0%, and that of the cables 0.1%. Therefore, the damping matrix in the dynamic response analysis was determined on the basis of the damping constants of these members. The characteristics of the effective amplitude and dynamic increment factor in various traveling states of the results of the simulation analysis are in comparatively good agreement with those of experiments. 20 refs., 17 figs., 5 tabs.

Fundamental experiment for flash removal of aluminum alloy by CO2 laser beam cutting; CO2 laser beam setsudan ni yoru aluminium gokin no ibaritori no kiso jikken

Energy Technology Data Exchange (ETDEWEB)

Kataoka, Y.; Tokunaga, T. [University of Industrial Technology, Kanagawa (Japan); Miyazaki, T. [Chiba Institute of Technology, Chiba (Japan)

1995-08-25

CO2 laser beam has been applied to cut of the aluminum alloy. Average cut width, roughness of cut surface and average thickness of heat affected zone are investigated as functions of laser power, cutting speed and assist gas pressure. The average cut width increases with laser power, but it does not depend on the cutting speed. The narrowest average cut width obtained is 0.22mm under the conditions of laser power of 900W and cutting speeds from 600 to 1000mm/min. The roughness of cut surface decreases with decreasing cutting speed. The best smoothness of cut surface obtained is 17 {mu}m (Rmax) , when the conditions are 1100W and 600mm/min. The average thickness of heat affected zone decreases with increasing assist gas pressure. CO2 laser beam cutting is applicable to flash removal from aluminum alloy casting. This process is expected to reduce the need of physical labor and to improve the working conditions in the foundry industry. 32 refs., 10 figs., 2 tabs.

Experimental results of acetone hydrogenation on a heat exchanger type reactor for solar chemical heat pump; Solar chemical heat pump ni okeru acetone suisoka hanno netsu kaishu jikken

Energy Technology Data Exchange (ETDEWEB)

Takashima, T; Doi, T; Tanaka, T; Ando, Y [Electrotechnical Laboratory, Tsukuba (Japan); Miyahara, R; Kamoshida, J [Shibaura Institute of Technology, Tokyo (Japan)

1996-10-27

With the purpose of converting solar heat energy to industrial heat energy, an experiment of acetone hydrogenation was carried out using a heat exchanger type reactor that recovers heat generated by acetone hydrogenation, an exothermic reaction, and supplies it to an outside load. In the experiment, a pellet-like activated carbon-supported ruthenium catalyst was used for the acetone hydrogenation with hydrogen and acetone supplied to the catalyst layer at a space velocity of 400-1,200 or so. In the external pipe of the double-pipe type reactor, a heating medium oil was circulated in parallel with the flow of the reactant, with the heat of reaction recovered that was generated from the acetone hydrogenation. In this experiment, an 1wt%Ru/C catalyst and a 5wt%Ru/C catalyst were used so as to examine the effects of variation in the space velocity. As a result, from the viewpoint of recovering the heat of reaction, it was found desirable to increase the reaction speed by raising catalytic density and also to supply the reactant downstream inside the reaction pipe by increasing the space velocity. 1 ref., 6 figs., 1 tab.

Experimental and analytical study on internal resonances in a cable-stayed beam model. Cableter dot hari model wo mochiita shachokyo no naibu kyoshin ni kansuru jikken to kaiseki

Energy Technology Data Exchange (ETDEWEB)

Fujino, Y.; Warnitchai, P.; Pacheco, B. (The University of Tokyo, Tokyo (Japan). Faculty of Engineering)

1991-07-15

This paper examines the dynamic characteristics on the model of the beam supported by one cable, the most simple type of cable-stayed bridge, with fundamental and important linear and nonlinear internal resonances from the experimental and analytical aspects. Vertical oscillation of the beam is able to cause parametric oscillation of the cable, so that dynamic phenomena which derive from internal resonance such as saturation of amplitude of vertical oscilation of the beam are observed experimentally. Based on the concept of local and global oscillation modes, a 3-DOF(degree of freedom) model is formulated considering the geometric nonlinearity of the cable. Then, a test of a small model, taking notice of linear compound of the cable and the beam as well as autoparametric compound by quadratic nonlinear terms, is conducted under vertical and horizontal harmonic excitations. After identifying the parameter of the model, the experimental value is compared with the analytical value. As a result, it is shown that both of them are highly consistent with each other. 16 refs., 9 figs., 2 tabs.

Influence on driver fatigue of vertical vibrations over long distances. Assessment in terms of stress hormones; Driver no unten hiro ni okeru joge shindo no eikyo. Stress hormone wo shiyo to shite

Energy Technology Data Exchange (ETDEWEB)

Taguchi, T.; Inagaki, H. [Toyota Central Research and Development Labs., Inc., Aichi (Japan)

1998-05-01

Driving tests are conducted to obtain some indexes that describe the cumulative effect of the sense of tiredness. The heart rate, Mayer wave related sinus arrhythmia, respiratory sinus arrhythmia, urinary adrenaline, noradrenaline, and cortisol in saliva are tested. Adrenaline and Mayer wave related sinus arrhythmia are ultimately named in view of their correlation with tiredness. It is believed that tiredness is attributable to two factors, which are increase in mental stress and decrease in vigilance. An excitation test is then conducted using a motion simulator. Upon application of 4Hz vibrations (equivalent to the chest section resonance frequency), adrenaline increases sharply, and then decreases sharply upon termination of excitation. Upon application of 1.6Hz vibrations (equivalent to the head section resonance frequency), adrenaline increases but not sharply, and the elevated level is sustained for some time after excitation. Driving tests are next conducted using a vehicle with its suspension fixed and another with 1-2Hz vibrations reduced. Rise in the adrenaline level is found inhibited aboard the latter. No difference is detected in terms of Mayer wave related sinus arrhythmia between the two vehicles. 4 refs., 7 figs., 4 tabs.

Physical model experiment for wave field measurements by means of laser Doppler vibrometer. Measurement of three components; Laser Doppler shindokei ni yoru butsuri model jikken. Hado sanseibun no kenshutsu

Energy Technology Data Exchange (ETDEWEB)

Nishizawa, O; Sato, T [Geological Survey of Japan, Tsukuba (Japan); Lei, X [DIA Consultant Co. Ltd., Tokyo (Japan)

1997-05-27

In this experiment, a beam incident from an oblique direction is reflected by a spherical lens toward the direction of incidence. When the surface of a matter is vibrated by elastic waves, the spherical lens comes into a translation motion that accompanies the vibration. It follows accordingly that the vibration on the surface of the matter may be detected by sensing the spherical lens travelling speed. Three components of the vibration may be determined if beams are focused at one spot from three directions. Detection of the S-wave component by LDV (laser Doppler vibrometer) discloses the complicated wave field in a heterogeneous material, and this physical model experiment may be utilized in various fields of study. For instance, information about problems that may surface in the field work may be collected beforehand in a physical model experiment for developing an S-wave-aided probing method. For the study of seismic wave propagation in a complicated three-dimensional ground structure, a numerical model is not enough, and a physical model experiment will be an effective method to fulfill the purpose. In the monitoring of cracks in a rock, again, not only elastic wave velocity but also waveform information collected from a physical model experiment should be fully utilized. 6 refs., 6 figs.

Experiment for deep seismic reflections in Hidaka, Hokkaido. Comparison between Vibroseis and explosive data; Hidaka chiiki ni okeru shinbu hanno data no shutoku jikken. Vibroseis to dynamite no hikaku

Energy Technology Data Exchange (ETDEWEB)

Shimizu, N; Ikawa, T [Japex Jeoscience Institute, Tokyo (Japan); Ito, T; Tsumura, N; Shinohara, M; Ikawa, T. Ikawa, H.; Asano, Y; Tanaka, Y; Miyazono, N [Chiba University, Chiba (Japan); Arita, K; Moriya, T; Otsuka, K; Omura, T [Hokkaido University, Sapporo (Japan); Kimura, M [Osaka Prefectural University, Osaka (Japan); Hirata, N [The University of Tokyo, Tokyo (Japan); Okuike, S

1997-05-27

This is a prompt report. These days the importance of acquiring knowledge about the structure from the lower crust down to the upper mantle is often discussed with reference taken to Hyogo-ken Nanbu Earthquake. The Hidaka collision belt where the lower crust is exposed on the surface is a rare phenomenon in the world and has been the subject of seismic survey. As a part of the survey, experiments are conducted by the use of vibrations produced by Vibroseis and dynamite sources. Every one of the shot records (20-second record) from the two types of vibration sources contains a clear echo in the vicinity of 16 seconds supposedly from a level deeper than 40 kilometers, not to mention reflections from shallow levels. Although some studies have to be conducted before the reflecting geological boundary (possibly the upper mantle) of the echo near the 16-second point can be identified, yet this is probably the reflection from the deepest level ever obtained in the seismic reflection survey conducted in Japan`s land area. It is proved by this experiment that vibration from a vibrator can reach as far as that from explosion if the vibrator specifications are rightly chosen. 4 refs., 3 figs.

Experimental results of 2-propanol dehydrogenation with a falling-liquid film reactor for solar chemical heat pump; Solar chemical heat pump ni okeru ryuka ekimakushiki 2-propanol bunkai hanno jikken

Energy Technology Data Exchange (ETDEWEB)

Doi, T; Tanaka, T; Ando, Y; Takashima, T [Electrotechnical Laboratory, Tsukuba (Japan); Koike, M; Kamoshida, J [Shibaura Institute of Technology, Tokyo (Japan)

1997-11-25

A solar chemical heat pump is intended to attempt multi-purposed effective utilization of solar energy by raising low temperature solar heat of about 100 degC to 150 to 200 degC by utilizing chemical reactions. The chemical heat pump under the present study uses a 2-propanol (IPA)/acetone/hydrogen system which can utilize low-temperature solar heat and has large temperature rising degree. It was found from the result of experiments and analyses that IPA dehydrogenation reaction can improve more largely the heat utilization rate in using a falling-liquid film reactor than using a liquid phase suspended system. As an attempt to improve further the heat utilization rate, this paper reports the result of experimental discussions on inclination angles of a reaction vessel and feed liquid flow rate which would affect the fluid condition of the liquid film. As a result of the experiments, the initial deterioration in the catalyst has settled in about 15 hours, and its activity has decreased to about 60% of the initial activity. It was made clear that the influence of the inclination angle of the reaction vessel on the reaction is small. 5 refs., 7 figs.

Model experiment on detection and monitoring of fractures by using air as a tracer for seismic wave. 2; Kitai wo tracer to shita kiretsu no danseiha tansa no model jikken. 2

Energy Technology Data Exchange (ETDEWEB)

Watanabe, T; Takami, Y; Ishiga, T; Sassa, K [Kyoto University, Kyoto (Japan). Faculty of Engineering

1996-05-01

Clearance provided between two flat resin blocks (being stacked) used as a model of a crack in rocks was subjected to an experiment to investigate elastic wave propagation characteristics when the crack is filled with water and when injected with air. This paper reports the result of the experiment. The experiment was carried out on a case where a parallel flat layer of water (with a thickness of 2 mm) was used as a crack and a case where crack faces are contacted (small resin pieces are inserted into the crack). The experiment was conducted by injecting air bubbles (air) into the water saturated crack from its side to gradually expand the air bubble existing region. Seven ceramic piezoelectric elements (one is a vibration source) were arranged on top of a resin block and six elements beneath the block to measure a wave reflected from the crack face and a wave permeated through the crack. It was found that as the air bubble existing region is expanded, the amplitude of the permeated wave decreases remarkably (however, only to a certain level when the crack faces are contacted), and the amplitude of the reflected wave increases. 3 refs., 9 figs.

Annual Report (No. 9, fiscal 1994) of Research Laboratory of Carbonaceous Resources Conversion Technology, Kyoto University; Kyoto Daigaku Kogakubu jushitsu tanso shigen tenkan kogaku jikken shisetsu nenpo (1994 nendo No.9)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

Research activities at the above institute are reported. In an effort to develop advanced coal utilization techniques aiming at reduction in environmental impact, coals of Canadian origin are investigated in cooperation with Canadian researchers. Outstanding among the achievements are Professor Morio Okazaki's 'Study of manipulation of transfer of heat and substance in porous solid bodies' (winner of prize from The Society of Chemical Engineers, Japan), and Professor Tomoyuki Inui's 'Study of fuel synthesis using porous crystalline catalysts' (winner of prize from The Japan Institute of Energy). Various studies are now under way, which include the development of a technique of high-efficiency pyrolysis for coal etc. at the Research Laboratory of Carbonaceous Resources Conversion Technology; development of a zeolite separation membrane on a ceramic filter at the Hashimoto Laboratory specializing in chemical engineering; measurement of the effect of hydrostatic pressure in active carbon adsorption, research on the state of liquid phase adsorption, etc., at the Okazaki Laboratory; analysis of heated fluid in porous structures by means of the lattice Boltzmann method etc. at the Ogino Laboratory; research on coal liquefaction using iron/sulfur-based catalysts etc. at the Watanabe Laboratory. (NEDO)

Annual Report (fiscal 1995, No. 10) of Research Laboratory of Carbonaceous Resources Conversion Technology, Kyoto University; Kyoto Daigaku Kogakubu jushitsu tanso shigen tenkan kogaku jikken shisetsu nenpo (19995 nendo No. 10)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

The report covers Laboratory research activities and a decision that the Laboratory, established in April 1986, will be abolished as scheduled in April 1996. Important coal-related achievements of the Laboratory include the development of a rapid pyrolytic process, studies on coal gasification, propositions for enabling coal to dissolve into general-purpose solvents and for a liquid phase oxidation process, manufacture of advanced-function carbon materials from heavy-weight carbonaceous resources (development of next-generation coke production techniques and of various element techniques for the clean use of coal), etc. As for its activities both domestic and international, the Laboratory, engaged in Education Ministry-financed high-priority scientific research projects, represented the general affairs division in a study titled 'Utilization of various energy resources,' and represented groups participating in other projects titled 'Development of new coal-gasification process' and 'Development of integral conversion process aiming at comprehensive coal utilization.' Furthermore, the Laboratory led the 'Japan-Canada cooperative scientific research relating to the development of technologies for effective coal utilization.' (NEDO)

Annual Report (fiscal 1995, No. 10) of Research Laboratory of Carbonaceous Resources Conversion Technology, Kyoto University; Kyoto Daigaku Kogakubu jushitsu tanso shigen tenkan kogaku jikken shisetsu nenpo (19995 nendo No. 10)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

The report covers Laboratory research activities and a decision that the Laboratory, established in April 1986, will be abolished as scheduled in April 1996. Important coal-related achievements of the Laboratory include the development of a rapid pyrolytic process, studies on coal gasification, propositions for enabling coal to dissolve into general-purpose solvents and for a liquid phase oxidation process, manufacture of advanced-function carbon materials from heavy-weight carbonaceous resources (development of next-generation coke production techniques and of various element techniques for the clean use of coal), etc. As for its activities both domestic and international, the Laboratory, engaged in Education Ministry-financed high-priority scientific research projects, represented the general affairs division in a study titled 'Utilization of various energy resources,' and represented groups participating in other projects titled 'Development of new coal-gasification process' and 'Development of integral conversion process aiming at comprehensive coal utilization.' Furthermore, the Laboratory led the 'Japan-Canada cooperative scientific research relating to the development of technologies for effective coal utilization.' (NEDO)

Model experiment on change of seismic properties of a fracture caused by injecting/draining water; Chusui/haisui ni yoru kison kiretsu no dansei denpa tokusei no henka ni kansuru model jikken

Energy Technology Data Exchange (ETDEWEB)

Watanabe, T; Koizumi, T; Sassa, K [Kyoto University, Kyoto (Japan). Faculty of Engineering

1997-05-27

Effect of water injection/draining on elastic waves penetrating through cracks is examined by measuring elastic waves before, during, and after the injection/draining of water into/from cracks in presence in granite. Two blocks of rock, with their crack-containing surfaces in contact with each other, are placed in a vessel, and water injection/draining is done through a hole on a vessel bottom side so that water will penetrate into the cracks. When the blocks are dry, there is almost no contact between the cracks, and so no crack penetrating waves are observed. Crack penetrating waves are produced when water is injected, and the position of the receiver sensing the penetrating waves changes as the water level rises. When the water level is lowered from the high water level, the waveform changes again as the level changes. The change in waveform is not so remarkable, however, as that observed during water injection thanks to the water residual in the cracks. It is now inferred that crack investigation is more effective when it is carried out with water being injected into dry cracks. The difference produced between the dry state and wet state when water is injected into dry cracks is used to detect the presence of cracks in this experiment, and this may be applied also to the investigation of cracks in the shallow part of the ground. 4 refs., 11 figs.

Annual Report (No. 9, fiscal 1994) of Research Laboratory of Carbonaceous Resources Conversion Technology, Kyoto University; Kyoto Daigaku Kogakubu jushitsu tanso shigen tenkan kogaku jikken shisetsu nenpo (1994 nendo No.9)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

Research activities at the above institute are reported. In an effort to develop advanced coal utilization techniques aiming at reduction in environmental impact, coals of Canadian origin are investigated in cooperation with Canadian researchers. Outstanding among the achievements are Professor Morio Okazaki's 'Study of manipulation of transfer of heat and substance in porous solid bodies' (winner of prize from The Society of Chemical Engineers, Japan), and Professor Tomoyuki Inui's 'Study of fuel synthesis using porous crystalline catalysts' (winner of prize from The Japan Institute of Energy). Various studies are now under way, which include the development of a technique of high-efficiency pyrolysis for coal etc. at the Research Laboratory of Carbonaceous Resources Conversion Technology; development of a zeolite separation membrane on a ceramic filter at the Hashimoto Laboratory specializing in chemical engineering; measurement of the effect of hydrostatic pressure in active carbon adsorption, research on the state of liquid phase adsorption, etc., at the Okazaki Laboratory; analysis of heated fluid in porous structures by means of the lattice Boltzmann method etc. at the Ogino Laboratory; research on coal liquefaction using iron/sulfur-based catalysts etc. at the Watanabe Laboratory. (NEDO)

Result of comparative experiment on environmental comfort in room using hot heat environment testing unit. Onnetsu kankyo shiken unit ni yoru shitsunai kankyo no kaitekisa no hikaku jikken kekka ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Fujiwara, T; Kawashima, K [The Hokkaido Electric Power Co. Inc., Sapporo (Japan)

1991-11-20

Measurements were carried out on three buildings having different heat insulation, airtightness and heat capacity for testing the hot heast enviroments (having a room size of about 4.6 m{times}3.7m{times}2.3 m) as to the temperature differences between the upper and lower parts of the room and the MRT (mean radiation temperature, representing the temperature of radiation from the wall face). These are compared according to types of heating appliance. The result is summarize as follows: The temperature difference in the upper and lower parts is affected largely by the airtightness of the building, the difference being capable of getting reduced by rasing the airtightness even in a buildings low in heat insulation. In a building with low airtightness, type of heating appliance and its installation location affect the temperature difference. The MRT is determined determined nearly completely by the heat insulation of the wall face in a room, but it tends to be affected easily by the specification and area of windows. A floor heating system increases the MRT and generates very little difference in temperatures in the upper and lower parts of the room. A comparison using a PMV (one of the indexes for enviromental comfort in a room) was also conducted. 12 figs., 7tabs.

Proceedings of the Spring Meeting of the Society of Naval Architects of Japan (1996). Part 1. Resistance, propulsion, advance, and ocean; Nihon zosen gakkai (1996 nen) shunki koen ronbun maezuri. 1. Teiko, suishin shindo, kaiyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-31

This is a proceedings of the Spring Meeting of the Society of Naval Architects of Japan made public on May 15 and 16, 1996. In the basic research, the following were included: Numerical simulation for submerged body fitted with hydrofoil; Simulation of tandem hydrofoils by finite volume method with moving grid system; Determination of the unknown method surface of planning plates by a formulation based on high aspect ratio approximation; Numerical simulation of a bubble flow by modified density function method, etc. As to floating bodies, Response characteristics of a long life type floating offshore airport in waves (3rd report: Response due to short waves and an attempt of active inclination control); Feasibility design of a floating airport and estimation of environmental forces on it; On the estimation method of hydrodynamic forces acting on a huge floating structure, etc. In addition, A numerical prediction with `DMDF` model of pack ice motion in the Okhotsk Sea; Development of an observation robot `Flying Fish` for comprehensive measurements of ocean environment; Water entry simulation of free-fall lifeboat, etc.

Proceedings of the Spring Meeting of the Society of Naval Architects of Japan (1996). Part 1. Resistance, propulsion, advance, and ocean; Nihon zosen gakkai (1996 nen) shunki koen ronbun maezuri. 1. Teiko, suishin shindo, kaiyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

This is a proceedings of the Spring Meeting of the Society of Naval Architects of Japan made public on May 15 and 16, 1996. In the basic research, the following were included: Numerical simulation for submerged body fitted with hydrofoil; Simulation of tandem hydrofoils by finite volume method with moving grid system; Determination of the unknown method surface of planning plates by a formulation based on high aspect ratio approximation; Numerical simulation of a bubble flow by modified density function method, etc. As to floating bodies, Response characteristics of a long life type floating offshore airport in waves (3rd report: Response due to short waves and an attempt of active inclination control); Feasibility design of a floating airport and estimation of environmental forces on it; On the estimation method of hydrodynamic forces acting on a huge floating structure, etc. In addition, A numerical prediction with `DMDF` model of pack ice motion in the Okhotsk Sea; Development of an observation robot `Flying Fish` for comprehensive measurements of ocean environment; Water entry simulation of free-fall lifeboat, etc.

Application of a temperature selective storage tank solar system. Part 4. Fundamental experiment under a solar simulator; Ondo sentaku chikunetsuso no solar system eno tekiyo. 4. Solar simulator ni yoru kiso jikken

Energy Technology Data Exchange (ETDEWEB)

Kanayama, K; Endo, N; Baba, H; Okamoto, A [Kitami Institute of Technology, Hokkaido (Japan); Kamiya, Y [Kanto Gakuin University, Yokohama (Japan)

1996-10-27

The storage tank is classified into a mixed type and stratified type. The stratified type is judged to be more advantageous from a viewpoint of the effective energy utilization. An experiment was made using a solar simulator to put the system, consisting of a vacuum double-glass tube collector and temperature selective storage tank, to practical use. The ejection position of the storage tank at the top is superior to that at the bottom, in the 60{degree}C layer of three layers (60, 40, and 20{degree}C). The ejection position hardly varies with the shape (straight or elbow) of an ejection port. When the temperature stratified layer is formed in two layers (40 {times} 2, 20{degree}C) to three layers (60, 40, and 20{degree}C), heat can be stably stored as the flow rate is higher. The stratified storage tank is inferior to the mixed storage tank in heat collection efficiency, but the specific exergy increases. By increasing the number of heat storage layers, the result of this experiment can also be applied to the linear temperature gradient layer obtained in the practical use. As a result of the above experiment, the basic data for an automated system design during practical application was obtained. 3 refs., 15 figs.

Study on the annular leakage-flow-induced vibrations. 1st Report. Stability for translational and rotational single-degree-of-freedom systems; Kanjo sukimaryu reiki shindo ni kansuru kenkyu. 1. Heishin oyobi kaiten 1 jiyudokei no anteise

Energy Technology Data Exchange (ETDEWEB)

Li, D.W. [Hitachi, Ltd., Tokyo (Japan); Kaneko, S. [The University of Tokyo, Tokyo (Japan); Hayama, S. [Toyama Prefectural University, Toyama (Japan)

1999-07-25

This study reports the stability of annular leakage-flow-induced vibrations. The pressure distribution of fluid between a fixed outer cylinder and a vibrating inner cylinder was obtained in the case of a translationally and rotationally coupled motion of the inner cylinder. The unsteady fluid force acting on the inner cylinder in the case of translational and rotational single-degree-of-freedom vibrations was then expressed in terms proportional to the acceleration, velocity, and displacement. Then the critical flow rate (at which stability was lost) was determined for an annular leakage-flow-induced vibration. Finally, the stability was investigated theoretically. It is known that instability will occur in the case of a divergent passage, but the critical flow rate depends on the passage increment in a limited range: the eccentricity of the passage and the pressure loss factor at the inlet of the passage lower the stability. (author)

Thermal structure of east and Southeast Asia. Comparison of results of Curie point depth analysis and heat flow data; Totonan Asia chiiki no ondo kozo. Curie ten shindo kaiseki kekka to chikaku netsu ryuryo tono hikaku

Energy Technology Data Exchange (ETDEWEB)

Tanaka, A; Okubo, Y; Matsubayashi, O [Geological Survey of Japan, Tsukuba (Japan)

1997-10-22

This paper describes the distribution of Curie point depth and its characteristics determined from the spectral analysis of magnetic anomaly data in East and Southeast Asia. It also describes relationships between the Curie point depth and the other geophysical information such as topography, heat flow data and tectonics. The Curie point depths are shallower than about 10 km at volcanic and geothermal areas, between 15 and 25 km at island arcs and back arc rifts, deeper than 20 km at continents, and deeper than 30 km at trenches. The Curie point depth (Dc) estimated from the heat flow data can be expressed by Dc=k{theta}c/q where k is thermal conductivity, q is heat flow, and {theta}c is Curie point. Based on the Curie point depths obtained from Curie point depth analysis in the cross section of northeast Japan and the averaged values of heat flow at individual points, they are distributed along a line of k{theta}c=1500[Wm{sup -1}]. Values of k{theta}c are small near the axis of Japan trench and large in the northeast Japan. It is considered that local anomalies can not be grasped from the spectral analysis. 21 refs., 3 figs.

Development of advanced heat pump (2). Prelimirary test of two-stage compression heat pump. Koseino onreinetsu kyokyu heat pump system no kaihatsu. Dai 2 ho 2dan attsusyuku system shisakuki no yobi jikken kekka

Energy Technology Data Exchange (ETDEWEB)

Iwatsubo, Tetsushiro; Saikawa, Michinori; Hamamatsu, Teruhide

1988-03-01

A heat pump driven by electricity is one of the excellent electricity utilization systems and is promoted to be widely used. An advanced heat pump has been investigated to enlarge its applications in the field of hot water supply for domestic use which will be competitive with city gas and air conditioning in large scale buildings. An experimental unit with two-stage compression system was designed, which has the multi-function of air conditioning and hot water supply, and the trial system was fabricated. In the design, followings were considered; cooperative operations of two compressors by inverter driving, the temperature conditions of both the air for the air conditioning and the heat source, additional setting of the intermediate heat exchanger. The test operation was carried out with checking the start up procedure, the control sequence and so on. The probability of five operation modes: cooling, heating, hot water supply, cooling/hot water supply, and heating/hot water supply, were confirmed. In the mode of heating/hot water supply the hot water temperature was increased to 65/sup 0/C, the excellent performance in hot water supply was demonstrated. (21 figs, 8 tabs, 1 photo, 5 refs)

Study on solar chemical heat pump system. Basic experiment on falling film reaction for dehydrogenation of 2-propanol; Solar chemical heat pump no kenkyu. 2-propanol bunkai hanno ni okeru ryuka ekimakushiki hanno jikken

Energy Technology Data Exchange (ETDEWEB)

Doi, T; Ando, Y; Tanaka, T; Takashima, T [Electrochemical Laboratory, Tsukuba (Japan); Nomura, T; Kamoshida, J [Shibaura Institute of Technology, Tokyo (Japan)

1996-10-27

An experiment and the examination were carried out in order to elucidate the optimum conditions in the falling liquid film reaction method, in the conversion of solar energy using the decomposition reaction of 2-propanol. The device for the experiment was constituted of a reaction container, tubular pump, cooling pipe, sampling container for effluent from the upper and lower part of the reaction container, and gas burette. Examined in the experiment were various factors such as a fibrous activated carbon (catalyst support), ratio for carrying catalyst, catalytic composition and heating temperature. In the experiment, with the temperature inside the reaction container fully stabilized under prescribed conditions, measurement was done for the hydrogen generation by the gas burette for 10 minutes as well as for the sampling of effluent. The experiment revealed that the heat utilization ratio reached the maximum of about 27% when the heating temperature was 90{degree}C using a catalyst with the ratio of RU and Pt 1 to 1 and the ratio for carrying catalyst 10wt%, so that a great improvement was obtained in the heat utilization ratio at a low temperature. Also obtained was a large inversion ratio of about 15%. 4 refs., 6 figs., 5 tabs.

Customers` response to residential peak-activated pricing. Evidence from a Japanese experiment; Peak taio ryokinka ni okeru kateiyo juyoka no fuka chosei kodo no bunseki. Kansetsu fuka seigyo jikken data wo mochiita kakaku koka no sokutei

Energy Technology Data Exchange (ETDEWEB)

Asano, H. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1997-10-01

Demand side management through a pricing mechanism, that is the indirect load control was experimented to analyze the pricing effect. When power consumption in indirect load control groups is compared between peak time band in weekdays in summer and off-the-peak time band, the power is less consumed when price gap is set than in a uniform charge time. When more number of persons is in home in daytime, room cooling is used in daytime including the peak band to adjust the demand. The substitution elasticity in price between demands in the peak time band and the off-the-peak time band is from about 0.06 to 0.07, which cannot be ignored. If the peak price is increased by four times, the demand in the peak band can be reduced by about 0.15 kW (when average power demand per household is assumed 0.75 kW). For room cooling devices, the first device is often installed in a living room and the second and further units in individual rooms such as bed rooms. The more the number of device, the higher the possibility that the use time band is outside the peak time band. This indirect load control experiment is a field test related to the peak-activated pricing for small power users, by which the users` behavior against the pricing effect was identified quantitatively. 5 refs., 1 fig., 8 tabs.

Computation accuracy of flow conditions around a very large floating structure using a multi-layer model. Comparison with experimental results; Taso model ni yoru choogata futai mawari no ryukyo keisan seido ni tsuite. Jikken tono hikaku

Energy Technology Data Exchange (ETDEWEB)

Kyotsuka, Y [Kyushu University, Fukuoka (Japan); Omori, H; Nakagawa, H; Kobayashi, M [Mitsui Engineering and Shipbuilding Co. Ltd., Tokyo (Japan)

1996-04-10

As one of the environmental problems in sea areas surrounding a very large floating structure (VLFS), change in flow condition is important, and it is one of the factors dominating the prediction of succeeding diffusion and ecosystems. Although a multi-layer model is in wide use for computation of flow condition and diffusion in one inner bay, its applicability should be reexamined because of no consideration of VLFSs. In this study, flow velocity profiles around a barge were then measured through the towing test of a barge in shallow water, and compared with computation results using a multi-layer model. The multi-layer model computed the flow velocity profiles by dividing the flow region to be computed into normal one and that under VLFS, and determined pressures under VLFS by 2-D Poisson`s equation. Slip condition was used as boundary condition at the bottom considering the number of layers under VLFS. Further numerical computation was conducted by 2-D MAC method, in particular, to compare flow around the wake of VLFS with experimental one. Both computation results well agreed with experimental one. 3 refs., 9 figs., 1 tab.

Application of magnetotelluric method to hydrocarbon exploration. Case study of MT survey in Yurihara oil and gas field, Akita prefecture; MT ho no kokunai sekiyu tanko eno tekiyo. Akitaken Yurihara chiiki ni okeru jikken chosa kekka

Energy Technology Data Exchange (ETDEWEB)

Mitsuhata, Y; Matsuo, K; Ishikawa, H; Tanaka, H; Nakagami, K [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

1996-10-01

The experiment and survey were carried out to verify the effectiveness and limitation of MT method. The previous seismic reflection method is unsuitable for steep terrain and over-folded complicated geological structure. In such difficult areas, application of MT method is increasing as complement or substitution for the reflection method. However, the evaluation of resistivity structure interpretation for every area is slightly difficult because of lack of data, poor quality of data, and no verification data at boreholes. Consequently, the survey was again carried out in well-known Yurihara oil and gas field, Akita prefecture whose geological structure has been surveyed in detail at boreholes, by adding new 32 sites, 22 sites on the south side and 10 sites on the north side of the measuring line extending from east to west. As a result, it was clarified that the lower high-resistivity layer found by MT method is equal to the Nishikurosawa basaltic layer, and basalt extends to the west in the north area. This result can`t be simply compared with the previous geological profile. 8 refs., 8 figs.

Report on survey on geothermal development promotion in fiscal 1999. Report on survey on environmental effects - noise and vibration (No. B-5, Busadake Area); 1999 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa (soon shindo) hokokusho (No.B-5 Busadake chiiki)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Identification of noise and vibration levels and evaluation on environmental effects were performed in association with the excavation in the geothermal investigation well drilling point (well N11-MD-3) and the vicinity thereof in the Busadake area in Hokkaido. In the survey, noise and vibration were measured before and during the well excavation at the well drilling point and nearby four points (boundary of the drilling premises, 500-m point, Kawakita Spa and the entrance to the mountain stream of petroleum). In addition, a distance decay survey was carried out at five points in one direction from the well drilling point. The result of the noise measurement showed the value of about 30 to 50 dB before the well excavation at the drilling point and its vicinity, and about 40 to 60 dB during the excavation. The vibration was about 40 dB at the boundary of the premises during the excavation, whereas the places other than them showed the lower limit of measurement. In the distance decay of the noise, 75 dB at the 10-m point decayed to 50 dB or lower in the 200-m point, while the vibration level of 75 dB decayed to 30 dB or lower in the 100-m point. These facts lead to a conception that the noise and vibration in association with the well drilling would not give great influence on the neighboring environment. (NEDO)

Study on heat collector of the solar system utilizing outdoor air. Experimental results in cases of cold and warm regions; Gaiki donyushiki solar system no shunetsubu ni kansuru kenkyu. Kanreichi to ondanchi ni okeru shunetsu jikken to kosatsu

Energy Technology Data Exchange (ETDEWEB)

Komano, S; Ebara, Y [OM Solar Association, Shizuoka (Japan); Wada, H [Wada Building Constructors Co. Ltd., Hokkaido (Japan)

1996-10-27

An experiment on heat collection was made in the heat collector of a solar system utilizing outdoor air in cold and warm regions. In this system, outdoor air is heated by the air circulation layer on the roof exposed to solar radiation. The heated air is supplied to the object space for heating and ventilation. In the experiment in a cold region, the heat collection characteristics can be adjusted by putting a baffle plate in the air duct according to the experiment of a glass heat collector. The heat collecting air layer on only the iron roof may leak or freeze in the region subject to coldness or heavy snowfall. Therefore, preheat forms the space of a garret, and the preheat temperature comparatively becomes low. The data in which the heat collection characteristics can be adjusted using only a glass heat collector is required corresponding to the regional situation. In the experiment in a warm region, an experiment was made inclusive of the preheat for which outdoor air is absorbed at the eaves. As a result, the heat collection characteristics of preheat were improved. Moreover, a heat collection temperature of about 60{degree}C was obtained on the heat collection surface including the preheat. 1 ref., 12 figs., 3 tabs.

FY 1990 report on the R and D of the manganese nodule mining system. 2/6 volume. Total system (experimental plan); 1990 nendo mangan dankai saiko system no kenkyu kaihatsu seika hokokusho. 2/6. Total system (jikken keikaku) hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

For the purpose of securing the stable supply of non-ferrous metal resources such as Ni, Co, Cu and Mn and of improving the overall ocean development technology, the R and D were carried out of a technology to mine Mn nodules existing in the bottom of deep sea of the depth between 4,000m and 6,000m by the fluid dredging method which is highly efficient and reliable. Therefore, plans of experiments to be made for each subsystem are adjusted/integrated to make the contents of a comprehensive experiment, and at the same time a draft of the comprehensive experiment plan was worked out for an experimental system to be developed/trially fabricated. As to a total system (experimental plan), a plan for execution was studied in the case of rationalizing the comprehensive ocean experiment plan and choosing between pump lift and air lift. The TA-C sea area was continuously investigated as a candidate sea area for survey and the range was limited. The paper studied the basic plan of the mining system and commenced the basic study of the assessment of economical efficiency. (NEDO)

Measurements of ultrasonic waves by means of laser Doppler velocimeter and an experimental study of elastic wave propagation in inhomogeneous media; Laser doppler sokudokei ni yoru choonpa keisoku to ganseki wo mochiita fukinshitsu baishitsu no hado denpa model jikken

Energy Technology Data Exchange (ETDEWEB)

Nishizawa, O; Sato, T [Geological Survey of Japan, Tsukuba (Japan); Lei, X [Dia Consultants Company, Tokyo (Japan)

1996-05-01

In the study of seismic wave propagation, a model experimenting technique has been developed using a laser Doppler velocimeter (LDV) as the sensor. This technique, not dependent on conventional piezoelectric devices, only irradiates the specimen with laser to measure the velocity amplitude on the target surface, eliminating the need for close contact between the specimen and sensor. In the experiment, elastic penetration waves with their noise levels approximately 0.05mm/s were observed upon application of vibration of 10{sup 6}-10{sup 5}Hz. The specimen was stainless steel or rock, and waveforms caught by the LDV and piezoelectric device were compared. As the result, it was found that the LDV is a powerful tool for effectively explaining elastic wave propagation in inhomogeneous media. The piezoelectric device fails to reproduce accurately the waves to follow the initial one while the LDV detect the velocity amplitude on the specimen surface in a wide frequency range encouraging the discussion over the quantification of observed waveforms. 10 refs., 7 figs.

Study of a fuel injection quantity sensor in diesel engine. Part 3. Experimental evaluation of the improved type micro turbine sensor; Diesel kikan ni okeru nenryo funsharyo sensor no kenkyu. 3. Funsharyo keisoku no seido kojo ni kansuru jikken hyoka

Energy Technology Data Exchange (ETDEWEB)

Maehara, H; Iwasaki, T; Kobayashi, T [Zexel Corp., Tokyo (Japan)

1997-10-01

A Micro Turbine Sensor has been developed to measure fuel injection quantity and injection rate. Previous reports described results of experiments on the MTS which were carried out under steady and unsteady flow conditions. The MTS has been improved in shape of a holder tip and a detecting procedure for rotating speed of a turbine. As a result revolution speed of the turbine increased 18% over the conventional type holder under steady flow condition. Furthermore the measurement resolution of the MTS came up to about 2(mm{sup 3}/pulse) at 20(mm{sup 3}/stroke) under intermittent spray conditions using fuel injection pump. 11 refs., 11 figs., 1 tab.

Report on achievements in fiscal 1991. Research and development of manganese nodule mining system (total system - experiment plan - edition/second of six volumes); 1991 nendo mangan dankai saiko system no kenkyu kaihatsu seika hokokusho. 2/6. Total system (jikken keikaku) hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-06-01

It is intended to research and develop a system for mining manganese nodules existing on deep ocean bottoms by using the fluid dredging system. A mining experimenting system will be developed, and fabricated on a trial basis to perform comprehensive ocean experiments, identify its performance, and collect different design data for a system to be used practically in the future. Fiscal 1991 has performed the following items: (1) detailed design on a comprehensive ocean experimenting device, and fabrication of part of the device, (2) preparation of experiment execution procedures for the comprehensive ocean experiment plan, and surveys on the experimenting ocean areas, (3) the comprehensive experiment simulation on behavior of the mine collecting device when settled on the ocean bottom, and strength of the ore lifting pipe considering safety, and (4) discussions on the basic plan for the mining system. The system under the research and development in progress is a system combining ore collection by water flow blow-up and suction, ore lifting by using a fluid dredge, and device towing. The ore collecting efficiency is defined as (nodule take-in quantity)/(take-in area in existence), whereas the water flow blow-up and suction system has greater advantage because of being simple in device configuration. The supply efficiency is defined as (nodule supply quantity to ore lifting device)/(nodule take-in quantity). Combination of the ore collection using the water flow blow-up and suction system with the ore lifting using the fluid dredge is a best selection. (NEDO)

Natural convection and radiation heat transfer in a vertical porous layer with a hexagonal honeycomb core. 2nd Report. Experiment on heat transfer; Honeycomb core de shikirareta enchoku takoshitsu sonai no shizen tairyu - fukusha fukugo netsu dentatsu. 2. Dennetsu jikken

Energy Technology Data Exchange (ETDEWEB)

Yamaguchi, Y; Asako, Y [Tokyo Metropolitan Univ., Tokyo (Japan). Faculty of Technology

1997-06-25

The combined natural convection and radiation heat transfer characteristics in a vertical porous layer with a hexagonal honeycomb core were investigate experimentally. The temperature distributions on the honeycomb core wall and the combined heat transfer rates through the porous layer were measured. The measurements of the heat transfer were accomplished using the guarded hot plate (GHP) method. The honeycomb core wall was made of paper and large mesh foamed resins were inserted into the honeycomb enclosures. The measurements were performed while varying the radiation parameters between 0.5 to 0.65, varying the temperature ratios between 0.01 to 0.1 and varying the Darcy-Rayleigh numbers between 5 to 80, and for a fixed aspect ratio of H/L=1. The experimental results for Nusselt numbers agreed well with our available numerical results. 9 refs., 8 figs.

Technology to prevent deposition of marine organisms by means of electrically conductive coating. Discussions on current and potential distribution by using experiments; Doden tomaku ni yoru kaiyo seibutsu fuchaku boshi gijutsu. Denryu den`i bunpu ni kansuru jikken ni yoru kento

Energy Technology Data Exchange (ETDEWEB)

Usami, M; Masaki, T [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan); Ueda, K

1996-04-10

Steel structures in sea water and surface of hulls are deposited with such marine organisms as microorganisms, algae and shellfish. The deposition causes a large problem such as occurrence of abnormal local corrosion in the structures, and increase in cruising resistance in ocean vessels. The present study has introduced a simplified equation of estimation for current and potential distribution in parts coated with an electrically conductive film, and verified its reasonability by an experiment. The equation of estimation was introduced by following a model of current flow in the electrically conductive coating. The experiment has the conductive coating applied to the interior of a concrete water tank with a length of 10.8 m, a width of 5 m and a depth of 3 m to measure potential at different locations. The conductive coating was energized from copper foils attached on each applied face, whereas the current was applied to two faces between the conductive films as a pair among the four coating applied faces to measure potential in each location. A simulated calculation revealed that the potential range in the depth direction is made smaller if specific resistance of the conductive film is decreased, and made greater if increased. Effectiveness of the equation of estimation was verified by an experiment. This method has provided a prospect of achieving optimization of the specification for application of the conductive film. 2 refs., 7 figs.

Attempt to measure the temperature, pressure and particle velocity of pyrocastic surge with penetrator-type gauge. ; Airdropping experiment at Unzen volcano. Penetrator hoshiki ni yoru kasai surge no ondo, atsuryoku, ryushi sokudo sokutei no kokoromi. ; Unzendake ni okeru toka jikken

Energy Technology Data Exchange (ETDEWEB)

Taniguchi, H. (Science Education Institute of Osaka Prefecture, Osaka (Japan)); Kamata, K.; Sange, K. (Kobe University, Kobe (Japan). Faculty of Science); Nakada, S. (Kyushu University, Fukuoka (Japan). Faculty of Science); Kamata, H. (Geological Survey of Japan, Osaka Office, Osaka (Japan))

1992-08-01

This paper describes development of a penetrator intended of measuring temperatures, pressures, and particle velocities of air blasts and pyroclastic surges occurring in volcanos, and its airdropping experiment. This device forms a spear with a total length of 150 cm to 160 cm disposed with wings at the tail, and a stopper to prevent the spear from penetrating into ground deeper than 60 cm. The device for measuring temperatures suspends metal pieces of 16 kinds in total including such metals as lead and tin, and such alloys as eutectic solders and type lead to enable measuring a temperature range from 100[degree]C to 810[degree]C . The device for measuring pressures consists of a square pipe with a length little shorter than one meter, twisted to 22.5[degree] at three locations, each of the 16 faces made from the twisting being attached with two blast meters (using lead and copper foils, serving also as particle velocity meters). Twelve prototype devices have been dropped (not having been recovered yet) on five points of the east side slope of Mt. Unzen using a helicopter. 5 refs., 3 figs.

FY 1992 Report on the results of the research and development of manganese nodule collection system. Total system (Test schedules); 1992 nendo mangan dankai saiko system no kenkyu kaihatsu (mangan dankai saiko system) seika hokokusho. 2/5. Total system (jikken keikaku) hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This project is aimed at development of the fluid dredging type technologies for collecting manganese nodules on deep sea beds (4,000 to 6,000m deep), in order to secure stable supply of the non-ferrous metal resources and improve marine development technologies. The test sea area determined is the seamount JA-4 south of the Minami-Torishima Island. The test schedule preparation working group has drawn the draft test schedules; the phase 1 tests (including water lifting and towing tests) at the TA-GA area, a sea area with a relatively thick acoustic transparent layer, located on the east side of the center of the flat peak of the seamount, and phase 2 tests (including mineral lifting tests) at the TA-GB area, a terrace on the south-east side of the flat peak of the seamount, where seamount manganese nodules are massively occurring. The studies for preparing the test schedules are started, based on the drafts, and also the studies are implemented for the test implementation manuals, including those suitable for No.3 Hakuryu as the test vessel. The other items studied include the basic studies on the air lift system for collecting minerals on a commercial scale, and on economic evaluation. (NEDO)

Fundamental study on the new method to estimate vibration level on a ship. Formulation of the damping matrix based on dissipation energy caused by fluid viscosity; Senpaku no shindo level suitei ni kansuru kisoteki kenkyu. Ryutai no nensei ni yoru san`itsu energy ni motozuku gensui matrix no teishikika

Energy Technology Data Exchange (ETDEWEB)

Funaki, T.; Hayashi, S. [Osaka University, Osaka (Japan). Faculty of engineering

1996-12-31

It is known in estimating vibration characteristics of a ship that fluid range affects largely a structure. In order to analyze the compound vibration therein, a method was proposed, which estimates vibration levels without using the finite element method. However, the problem of mode decay ratio has not been solved. Therefore, this paper first describes a method to introduce an equivalent linear decay matrix. The paper then mentions difference in the decay effects due to fluid viscosity in a shallow and deep water regions. Furthermore, vibration levels in the deep water region were estimated in a model experiment to verify the estimation result. Under a hypothesis that two-node vibration in a rotating ellipse has displacement distributions in the deep and shallow water regions equivalent, and when a case of vibration in a layer flow condition is calculated, dissipation energy in the shallow region is larger than that in the deep region by about 26%. About 5% of the total dissipation energy is consumed at bottom of the sea. According to a frequency response calculation, estimated values for the response levels still differ from experimental values, although the trend that the vibration levels change can be reproduced. 6 refs., 15 figs., 2 tabs.

Fundamental study on the new method to estimate vibration level on a ship. Formulation of the damping matrix based on dissipation energy caused by fluid viscosity; Senpaku no shindo level suitei ni kansuru kisoteki kenkyu. Ryutai no nensei ni yoru san`itsu energy ni motozuku gensui matrix no teishikika

Energy Technology Data Exchange (ETDEWEB)

Funaki, T; Hayashi, S [Osaka University, Osaka (Japan). Faculty of engineering

1997-12-31

It is known in estimating vibration characteristics of a ship that fluid range affects largely a structure. In order to analyze the compound vibration therein, a method was proposed, which estimates vibration levels without using the finite element method. However, the problem of mode decay ratio has not been solved. Therefore, this paper first describes a method to introduce an equivalent linear decay matrix. The paper then mentions difference in the decay effects due to fluid viscosity in a shallow and deep water regions. Furthermore, vibration levels in the deep water region were estimated in a model experiment to verify the estimation result. Under a hypothesis that two-node vibration in a rotating ellipse has displacement distributions in the deep and shallow water regions equivalent, and when a case of vibration in a layer flow condition is calculated, dissipation energy in the shallow region is larger than that in the deep region by about 26%. About 5% of the total dissipation energy is consumed at bottom of the sea. According to a frequency response calculation, estimated values for the response levels still differ from experimental values, although the trend that the vibration levels change can be reproduced. 6 refs., 15 figs., 2 tabs.

Achievement report for fiscal 1999 (edition B) on auxiliary New Sunshine Project. Development of coal hydrogasification technology (Research by using experimental device); 1999 nendo New Sunshine keikaku hojo jigyo seika hokokusho (B ban). Sekitan suiso tenka gaska gijutsu kaihatsu - Jikken sochi ni yoru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective of using practically the coal hydrogasification technology (the ARCH process), developmental research has been performed on important elementary technologies using different experimental devices. This paper summarizes the achievements in fiscal 1999. In the research by using a small testing apparatus, the Taiheiyo coal was used to have performed demonstration operation on the replacement natural maximized case, the heat efficiency maximized case, and the BTX maximized case. As a result, the three cases were found nearly as anticipated in the simulation, whereas the replacement natural gas maximized case has achieved the targeted whole coal conversion rate of 60% or more. However, the BTX maximized case presented a value lower than the targeted BTX yield of 12%. In the developmental research on the injector, the injector having been fabricated for the hot model test was given another combustion test, where the focal temperature of 1,200 degree C or higher was derived. The hot model test has verified the non-agglomeration performance of coal by using as parameters the focal temperatures, coal cross sectional area loads, coal types, and injectors. It was verified that the Taiheiyo and Shin Mu coals do not agglomerate excessively. (NEDO)

Achievement report for fiscal 1998 (edition B) on auxiliary New Sunshine Project. Development of coal hydrogasification technology (Research by using experimental device); 1998 nendo New Sunshine keikaku hojo jigyo seika hokokusho (B ban). Sekitan suiso tenka gaska gijutsu kaihatsu - Jikken sochi ni yoru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective of using practically the coal hydrogasification technology (the ARCH process), developmental research has been performed on important elementary technologies using different experimental devices. This paper summarizes the achievements in fiscal 1998. In the research by using a small testing apparatus, the Taiheiyo coal was used to have derived hydrogasification data (distribution and yield of the reaction products) in case of having changed the reaction pressure, temperature rising rate, and H{sub 2}/caoal ratio, and to verify the possibility of increasing the BTX yield by installing a temperature zone in two steps. In the developmental research on the injector, a combustion test and a coal feeding test were performed on the injector having been designed and fabricated in the previous fiscal year to verify the basic performance and evaluate the heat resistance and durability. With respect to the hot model test, a test installation was completed with the injector mounted to conduct the trial operation and test. In addition, development was conducted on the coal temperature rise simulation as the second phase of developing the simulation of mixing of coal with high-temperature hydrogen and temperature rise. (NEDO)

Natural convection heat transfer in an anisotropic porous cavity heated from the side. 2nd Report. experiment by hele-shaw cell; Tosuiritsu ni ihosei wo yusuru howa takoshitsu sonai no sokuho kanetsu ni yoru shizen tairyu netsu dentatsu. 2. Hele shaw cell ni yoru jikken

Energy Technology Data Exchange (ETDEWEB)

Kimura, S; Okajima, A; Kiwata, T [Kanazawa University, Ishikawa (Japan). Faculty of Engineering

2000-11-25

Natural convection heat transfer and flow structure in an anisotropic porous medium of square cavity saturated with Boussinesq fluid has been studied experimentally using a Hele-Shaw cell. The permeability ratio defined by K=K{sub y}/K{sub x} was put to three different values; 0.4, 1 and 2.5. The convection patterns at three different permeability ratios are visualized for several different Rayleigh numbers by the pH indicator method. When K is 0.25, the visualized flow is mainly in the vertical direction. On the contrary for K=4 the convecting flow is in the horizontal direction. The average heat transfer coefficients are also measured, and the corresponding Nusselt number are plotted as a function of K. It is found that the corresponding Nusselt numbers are scaled with (KRa){sup 1/2}. The experimental results of flow pattern and heat transfer are accord with those obtained by our previous theory. (author)

Achievement report for fiscal 1997 (edition B) on auxiliary New Sunshine Project. Development of coal hydrogasification technology (Research by using experimental device); 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho (B ban). Sekitan suiso tenka gaska gijutsu kaihatsu - Jikken sochi ni yoru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

With an objective of using practically the coal hydrogasification technology (the ARCH process), developmental research has been performed. This paper summarizes the achievements in fiscal 1997. In the research by using a small testing device, the Taiheiyo coal was used to have derived hydrogasification data (distribution and yield of the reaction products) in case of having changed the temperature, residential time and H{sub 2}/caoal ratio at a pressure of 7.0 MPa. In the developmental research on the injector, a test to verify mixing performance was performed by simulating the coal/hydrogen with gas/gas and coal/gas at normal temperature and pressure. Furthermore, discussions were given on the heat conduction analysis and cooling structure, whereas an injector was designed and fabricated. With respect to the hot model test to verify the performance of the injector, detailed design and partial fabrication of the test device were carried out. In addition, development was conducted on the coal/gas system mixing simulation to simulate the states of dispersion and mixing of the coal as the first phase of developing the mixing and temperature rise simulation. (NEDO)

Fiscal 1993 report on results of R and D on manganese nodule mining system. Manganese nodule mining system (Total system - experiment plan part); 1993 nendo mangan danakai saiko system no kenkyu kaihatsu seika hokokusho. 2/5. Mangan dankai saiko system (total system (jikken keikaku) hen)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Technology is being developed for mining the nodules existing at a depth of 4,000-6,000 m by a fluid dredge method, with the purpose of securing steady supply of non-ferrous metal resources and enhancing oceanic development technologies. To be concrete, comprehensive oceanic experiments will be conducted in the GA-04 sea area, 600 km southeast of Marcus Island, by developing and experimentally preparing a test system for the mining. In the R and D of a total system, activities were carried out in the two areas of (1) experimental operation section for design and manufacture of experimental equipment and comprehensive experimental simulation, and (2) experimental planning operation section for experimental policy, survey and analysis of sea area for experiment, and research on mining system. In (2), examination of the experiment implementation plan was carried out in the case where, as the experimental plan, the first stage experiment is implemented in TA-GA sea area and the second stage experiment in TA-TB sea area with abundant nodules of a submarine mountain in the area; examination was also made on the draft of an experiment implementation guideline suitable for M.S. Hakuryu No.3 as the experimental boat as well as on various guideline plans. In addition, a sensitivity analysis was made on the mining system as the evaluation of cost effectiveness in the case of commercial production. (NEDO)

Study on behavior of car and driver in the very small commuter car made of FRP during collision using scale model. Under the consideration of thorax deformation of driver using airbag; FRP sei mokei ni yoru FRP sei chokeiryo jissha shototsuji no kuruma to join no anzensei ni kansuru kenkyu. Kyobu henkei tokusei wo yusuru join ni taisuru air gab no koka

Energy Technology Data Exchange (ETDEWEB)

Sakai, H; Morisawa, M; Yoshino, T [Musashi Institute of Technology, Tokyo (Japan); Sato, T [Keio University, Tokyo (Japan); Ishizuki, H [Satake Co., Tokyo (Japan)

1997-10-01

In this study, after having performed simulation which took up scale models substituting for full scale model of commuter car made of FRP, we carried out collision tests to barrier. Here, we made enquiries about the occupant safety by changing the collision speed and the deformation characteristics of the seat belt, during head-on barrier collision using one-fifth scale models. We sought for the occupant`s safe combinations among the deformation characteristics of airbag and the thorax deformation. In this case, the degree of the occupants injury were estimated using HIC values, 3msecG and maximum deformation of the thorax. 7 refs., 5 figs.

Report on achievements in fiscal 1998. Venture business growing type consortium - small business creating infrastructure (Research and development of ultrasonic vibration machining and electrochemical reaction compound high-efficiency and ultra precision damage-free machining); 1998 nendo chochoonpa shindo denki kagaku hanno fukugogata konoritsu choseimitsu damage free kakoho no kenkyu kaihatsu seika hokokusho. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The present research and development is intended to establish the ultrasonic vibration machining process (ultrasonic vibration means vibration with frequency band exceeding 60 kHz), and ultrasonic vibration machining and electrochemical reaction compound machining process. The following research assignments were executed: (1) development of an ultrasonic vibration machining device and tools, (2) fundamental study on ultrasonic vibration grinding, (3) development of an ultrasonic vibration machining and electrochemical reaction compound damage-free grinding device and tools, and (4) development of ultrasonic vibration machining and electrochemical reaction compound damage-free grinding technology. The achievements in the current fiscal year may be summarized as follows: (1) an ultrasonic vibration rotating main-shaft unit and an electrically insulated tool holder were developed; (2) developments were made on a grinding process by using a micro-diameter grinding wheel supported by ultrasonic vibration, a micro field pick-up unit process using the same wheel, fabrication of micro tools by means of the ultrasonic vibration grinding, processing by using a drill with very small diameter based on the ultrasonic vibration grinding, and a technology to drill holes by means of ultrasonic vibration using a machine-made drill; (3) an ultrasonic vibration rotating main shaft unit with variable amplitude at 75 kHz was developed; and (4) an interface reaction compound grinding process supported by ultrasonic vibration was developed. (NEDO)

Research and development project for large industrial technologies in fiscal 1989. Achievement report on research and development of manganese nodule mining system - Volume 1/6 (Edition for total system - experiment system); 1989 nendo mangan dankai saiko system no kenkyu kaihatsu seika hokokusho. 1/6. Total system (jikken system) hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

With an objective to ensure non-ferrous metal resources such as nickel, cobalt, copper and manganese, and enhance the ocean development technologies, research and development has been performed on a technology to mine by using the fluid dredge system the manganese nodules existing in ocean bottoms as deep as 4,000 to 6,000 m. This paper summarizes the achievements in fiscal 1989. In the research and development of the total system, fabrication design was performed on a mining experimental vessel which takes the role of the base for the comprehensive ocean experiments. In addition, the comprehensive experiment implementation procedures were discussed, and such experimental simulation was carried out as operation of the vessel during handling and mining. Furthermore, discussions were given on the consistency of the ore lifting pipe and device with the handling system, and the system operating consistency, such as the handling method for the ore collecting machine. As part of the technical cooperation with France who is researching and developing independently a manganese nodule mining system, discussions were given on the compatibility of the mining experiment systems in Japan and France to execute the comprehensive experiments jointly. (NEDO)

Fiscal 1992 R and D project for large-scale industrial technology. Report on R and D results of manganese nodule mining system (1/6 volume) (Total system - experimental system part); 1991 nendo mangan dankai saiko system no kenkyu kaihatsu seika hokokusho. 1/6. Total system (jikken system) hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-06-01

In connection with the R and D of a deep sea bottom manganese nodule mining system, the results were summarized for the total system (experimental system) carried out in fiscal 1991. In the experimental system operation section, adjustment and examination were made on the issues and problems concerning design and manufacturing over each sub system continuously from the previous year, with the detailed design of the entire experimental system compounded. In addition, as an oceanic general experimental plan, consistency was confirmed between the development of the detailed design of the experimental system and the conditions of the area of the sea where the experiment was to be performed, with the points looked over for the implementation of the experiment, and with the behavior examined of the mining machine at the time of landing on the sea bottom in the general experiment simulation. Further, taking it into consideration that the boat for the mining experiment was a type of boat for oil rig and that its steering was dependent on towing by a tugboat, examination was started on the boat steering simulation at the time of tug towing. Furthermore, detailed design was started for the experiment system on the basis of the oil rig, with examination made on the principal particulars, weight, center of gravity, etc.. (NEDO)

Research and development project for large industrial technologies in fiscal 1989. Achievement report on research and development of manganese nodule mining system - Volume 2/6 (Edition for total system - experiment program); 1989 nendo mangan dankai saiko system no kenkyu kaihatsu seika hokokusho. 2/6. Total system (jikken keikaku) hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

With an objective to ensure non-ferrous metal resources such as nickel, cobalt, copper and manganese, and enhance the ocean development technologies, research and development has been performed on a technology to mine by using the fluid dredge system the manganese nodules existing in ocean bottoms as deep as 4,000 to 6,000 m. This paper summarizes the achievements in fiscal 1989. This fiscal year has reviewed and rationalized the experiment program for the purpose of largely reducing the experimental expense without damaging the purpose and achievement of the experiment. In the rationalized program, such programs were established as the dock side test at the quay and off shore of the Kobe Shipyard, a comprehensive trial operation in the sea area with depth of about 2,000 m, and comprehensive experiments in the sea area around 9 degrees 10 minutes north latitude and 146 degrees 30 minutes west longitude with depth of 5,150 m. Based on these programs, discussions were given on the personnel plan, operation management, fuel, and lubrication oil for the experimental vessel. In addition, discussions were given on the operation, maintenance management, operation management, communications, safety control, and hurricane countermeasures as the experiment implementation procedures. Furthermore, such discussions were given as investigation and selection of the environmental effects and the experimental sea areas for the experiment system. (NEDO)

New stimulation method with the function of narrowing and moving the stimulated region for cochlear implants. Its evaluation by the animal experiment and the numerical analysis; Jinko naiji no tame no shigeki bui no seneika to ido kino wo motta shigeki hoshiki. Suchi kaiseki to dobutsu jikken ni yoru hyoka

Energy Technology Data Exchange (ETDEWEB)

Miyoshi, S.; Sakajiri, M.; Ifukube, T.; Matsushima, J. [Hokkaido University, Sapporo (Japan)

1998-02-01

The electrical stimulation of the auditory nerve can elicit auditory sensations in the subjects with sensorineural deafness. Each stimulating electrode of an electrode array of the multi-channel cochlear implants may stimulate a distinct neural population. However, a great deal of current spreads from each electrode throughout a lymph because of the high electrical conductivity of the lymph liquid. This phenomenon causes the transmitted information to be reduce due to channel interactions. Even if the number of electrodes is increased, the transmitted information will be limited because of current spread. We have proposed the Tripolar Electrode Stimulation Method (TESM) which may succeed in narrowing the stimulation region and continuously moving the stimulation site for the cochlear implants. We evaluate whether or not TESM works according to a theory which is based on the numerical analysis using the auditory nerve fiber model consisted of unmyelinated and myelinated segments. In this simulation, the neural site and the am of the excited fibers are compared with the compound action potentials which we obtained through animal experiments. As a result, based on the numerical analysis using this model, it is also proved that the anodal/cathodal threshold stimulation current ratio increases by decreasing unmyelinated segment between the inner hair cell and the habenula perforate. Also by comparing the result of the numerical analysis with that of the animal experiment, It is suggested that an effect of the unmyelinated segment is not significant. Based on their results mentioned above, we succeed in narrowing a Stimulation region by controlling the am of the currents emitted from the electrodes on both sides. Also we succeed in continuously moving a stimulation site by changing the ratio of the currents emitted from the electrodes on both sides. 11 refs., 14 figs., 1 tab.

FY 2000 report on the results of the development of the stand-by consumption power reduction technology. Verification experiment on the technology to reduce stand-by power of household electric appliances; 2000 nendo taikiji shohi denryoku sakugen gijutsu kaihatsu seika hokokusho. Kaden seihin taikiji denryoku sakugen gijutsu no jissho jikken

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Study was made of the energy conservation by reducing stand-by consumption power of household electric appliances. In the study, remote control, household electric appliance, and outlet box were developed, and a system was developed in which each of the three was connected by network and the commercial power source supply is cut off at the time of the stand-by state of household electric appliances. The outlet box collectively manages timer information and reservation information. User sends out control command toward the outlet box using the two-way remote control, and controls all the household electric appliances connected via network. The screen data of household electric appliances are sent to the two-way remote control via the outlet box and presented to user. When the time comes for automatic execution such as video recording during absence, the outlet box carries commercial power source to household electric appliances. Using these appliances, verification experiment was carried out in the model house which was built with the ordinary house as model. A reduction in stand-by consumption power, approximately 218kWh/year(center dot)household, was verified. (NEDO)

Fiscal 1983 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1983 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (Chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-01

The effort aims to develop a reactor and its peripheral devices and process management technology therefor and to develop chlorosilane hydrogen-reduction process technology as part of the endeavors to develop a low cost production process for silicon for photovoltaic cells for the purpose of building a model plant capable of approximately 10 tons/year in terms of SOG (spin on glass) silicon. A study is made of ten operations (total reaction time of 2,264 hours), and it turns out that the electric power consumption efficiency is near the initially planned value. The yield of Si is, however, but 16.5% which is lower than the initially planned value of 20%. The value is elevated to 18% by raising the reactor temperature. To prevent overcleaning, a reactor with its internal walls experimentally coated with SiC is tested. The problems with devices other than the reactor tube are extraction rendered difficult by anomalously grown granules and processing devices choked by Si powder contained in waste gas after reaction. The first problem is settled by modifying the extraction tube but the other still needs a remedy. The produced granules are found to be high in quality. The seed producing roll crusher is operated for a total of 92 hours yielding 857kg in total. (NEDO)

Fiscal 1982 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1982 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (Chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

The effort aims to develop a reactor and its peripheral devices and process management technology therefor and to develop chlorosilane hydrogen-reduction process technology as part of the endeavors to develop a low cost production process for silicon for photovoltaic cells for the purpose of building a model plant capable of approximately 10 tons/year in terms of SOG (spin on glass) silicon. The installation of a 10 tons/year class model plant for SOG-Si production is completed in July 1982. Flaws are removed after a test run, and four reactions are accomplished without damage on the reactor tube in the period from February-end to March-beginning marking 550 hours of operation in total. Thanks to the four operations, 1,086kg of granules are experimentally produced and an electric power consumption rate of 30.6KWH/kg Si is achieved, control of the flowing particle amount by reactor differential pressure is accomplished and the same of the yield by recovered silane liquid composition analysis, and essence is seized of operation control technologies. In an experimental apparatus for seed production, Si is crushed by a roll crusher and then subjected to separation by a quartz-made air elutriator. A high yield of 130kg is obtained after crushing for 75 hours. (NEDO)

Achievement report for fiscal 1981 Sunshine Program on development of practical application technologies for photovoltaic power systems. Test production and verification of solar panels (Development of polycrystalline substrate process technologies); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo denchi panel jikken seisaku kensho (takessho kiban kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Studies are conducted to enlarge the diameter of polycrystalline Si castings and to develop a low-loss slicing method using silicon nitride powder as mold releasing agent. The apparatus for Czochralski's pulling process is improved and tested using SEG (selective epitaxial growth) Si, and now the casting of a 150mm-diameter ingot is feasible. Also, test production of a 94mm-square wafer as specified by NEDO (New Energy and Industrial Technology Development Organization) is successfully carried out. Difficulties in separating the mold releasing agent from the crucible are solved by changing the Si{sub 3}N{sub 4} power solution from PVA (polyvinyl alcohol) to ethyl silicate. The design, manufacture, and installation of the important parts of the system for the mass production of castings are now complete. The crucible is designed to be movable relative to the heater section, and the molten Si is allowed to cool and solidify from the bottom upward. In relation with the development of low-cost wafer manufacturing technologies, low-loss slicing methods are studied. It is concluded that under the current circumstances a multi-blade saw is more promising than the multi-wire saw in view of the damaged slice rate, processing speed, operating cost, and maintainability. (NEDO)

Fiscal 1985 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1985 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-03-01

The operation continues of the experimental device capable of producing 10 tons/year of SOG (spun on glass)-Si, and efforts are under way to carry out improvements, to verify such improvements for the results, and to develop operation control technologies. During the operation, improvements are made with respect to the length of stable operation period, granule quality, and device operation, and the results are verified. An automated control test system is verified, and a reactor tube newly developed by Shin-Etsu Chemical Company is subjected to a durability verification test. On the other hand, development is started of SiC-CVD (chemical vapor deposition) technology for materials for large reactor tubes, studies are started on a basic experimental device, basic studies are conducted for designing a large reactor, and investigations are conducted of a large plant conceptual design, an automated control system for reactors, and so forth. The results achieved are all found to be satisfactory. Above all, the granule quality is improved to be quite high in purity, and a cast cell made from improved granules exhibits a photoelectric conversion efficiency to exceed 13%. It is also found that the newly developed reactor tube is stronger than conventional reactor tubes and will be advantageous over others in the future enlargement of devices. (NEDO)

Fiscal 1986 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1986 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (Chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-03-01

The aim is to develop a fluidized bed reactor high in productivity and low in power consumption for the realization of mass production of low cost polycrystalline silicon usable for solar cell construction. An experimental device capable of producing 10 tons/year of SOG (spun on glass)-Si is built and operated. The fluidized bed reactor treating trichlorosilane as the material and the product quality achieve the initially set goals, and the essence is seized of operation management technology. In fiscal 1986, for development of the technology into a practical application technology, designs are prepared for a larger reactor unit and a large plant of the commercial scale. From the viewpoints of production efficiency and cost, the enlargement of a reactor unit is an inevitable task to discharge before practical application. There are two challenges to meet. One is the development of technologies for manufacturing large reactor tubes strong enough to withstand practical service and the other the development of a reactor structure fit for dimensional enlargement. It is then found that the concept of an economically optimum design relative to device series or device block formation is variable in the case of large plants, dependent on the scale of production, and that therefore it is necessary to arrange problems in a proper order to facilitate further deliberation. (NEDO)

Fiscal 1987 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1987 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (Chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

Since its construction in 1982, the experimental device capable of 10 tons/year production of SOG (spun on glass)-Si has been in operation, and the trichlorosilane processing fluidized bed reactor has achieved its goals in performance and product quality. Element studies continue for the enlargement of the reactor unit for practical application and for the designing of a large plant of the commercially viable scale. In fiscal 1987, element studies are conducted for the enlargement of the reactor unit. Concerning the development of technologies for the manufacture of large reactor tubes strong enough to withstand practical application, efforts are made to strengthen materials for the fabrication of reactor element tubes (230mm and 500mm in diameter), to develop SiC-CVD (chemical vapor deposition) technology to provide reactor tube materials with resistance to corrosion, and to develop a single reactor tube structure indispensable for device enlargement. For the verification of such element technologies, in line with the study of experimental device operation capable of 10 tons/year SOG-Si production, studies are conducted on continuous stable operation technologies for the fluidized bed reactor, maintenance and improvement of product quality, and enhancement of durability of constituent parts and components. (NEDO)

FY 1980 Report on results of Sunshine Project. Research and development of coal liquefaction techniques (Development of direct hydrogenation type liquefaction plant and 2.4 T/D test plant); 1980 nendo sekitan ekika gijutsu no kenkyu kaihatsu, chokusetsu suiten ekika plant no kaihatsu seika hokokusho. 2.4T/nichi jikken plant no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This program is aimed at construction and operation of a 2.4 T/D test plant for eventual commercialization of the direct hydrogenation type liquefaction process. The FY 1980 program includes designs of the test plant, procurement and manufacture of some equipment, and works for construction of the bases, buildings and scaffolds. The construction site for the 2.4 T/D plant was changed in July 1980 from Mitsui Engineering and Shipbuilding's Chiba works to NKK's Keihin Steelworks, which was accompanied by some changes in the basic and detailed designs. The detailed designs were reviewed for construction of the test plant, to reflect the results of the individual elementary researches. The works for the FY 1980 program also include preparations for obtaining approvals of plant construction, based on the revised designs, from the related government offices, and equipment procurement. This paper presents the major drawings for the plant construction, including those for PID designs, overall plant layouts, piping systems, buildings, scaffolds, and pipe racks. The loading data are also included. (NEDO)

Fiscal 1984 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1984 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-01

In fiscal 1984, studies are conducted for long-time stabilized operation of the device (extension of reactor tube service life, elimination of flaws in the granule extraction process, control of deposited silicon), improved granule quality (measures to deal with Cu pollution), cost reduction (improvement on yield of silicon after reaction, reduction in electric power consumption rate), and so forth. The results are found to be satisfactory in outline. The problem of strengthening the reactor tube material itself remains to be solved, however, with many knotty issues to settle before practical application. In the effort to deliberate these difficulties, as many as 4,377 hours (reaction hours) in total are spent in fiscal 1984. During the operation, 8.3 tons of granules are produced of which approximately 7 tons are fed to the next stage of processing. The quality of granules produced in this way is stable thanks to efforts to prevent pollution and to prolong continuous reaction time, and is found to satisfy NEDO (New Energy and Industrial Technology Development Organization) specifications. Furthermore, the cast cell and the ribbon cell using thus-produced granules achieve photoelectric conversion rates of 10% and 9%, respectively, thereby meeting the target goal of 9%. (NEDO)

FY 1980 Report on results of Sunshine Project. Development of coal liquefaction techniques (Development of 1 T/D test plant, and researches on the solvent-extraction type liquefaction process); 1980 nendo sekitan ekika gijutsu no kaihatsu, yozai chushutsu ekika plant no kaihatsu seika hokokusho. 1t/nichi jikken plant no kaihatsu, yozai chushutsu ekika process no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This program is aimed at establishing the techniques for solvent-extraction type coal liquefaction plant by constructing and operating a 1 T/D test plant to obtain the technical data for the efficient plant. The test plant is operated to confirm the effects of temperature and coal slurry concentration on liquefaction conversion by the solvent-extraction for a short time in the furnace for the extraction unit. The extraction type coal liquefaction tests can be conducted for a reaction time of around 1 hour by the test plant. The recycled solvent purification unit is installed, to regenerate the hydrogen donor solvent. For researches on the solvent-extraction type coal liquefaction process, the continuous extraction is conducted, to investigate the effects of extraction reaction rate at relatively low pressure. The optimum hydrogenation conditions are studied for the test plant. It is confirmed that a Mo-based catalyst is suitable for the hydrogenation. The batch type reaction system is operated to investigate the liquid yield of Wandoan coal, and recycled solvent balances and compositions. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program-assisted project. Part 1. Research and development of coal liquefaction technology (Development of direct coal hydroliquefaction plant; development of 2.4T/day-capable research plant); 1981 nendo sekitan ekika gijutsu no kenkyu kaihatsu / chokusetsu suiten ekika plant no kaihatsu seika hokokusho. 1. 2.4t/nichi jikken plant no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

The above-named plant is constructed, and studies are conducted on its operation. Before the construction of this 2.4T/day-capable research plant, its details were designed in fiscal 1979 when the plan placed the plant at the Chiba establishment of the Mitsui Engineering and Shipbuilding Co., Ltd. The plan was altered in July of fiscal 1980 for the plant to be built at the Keihin steelworks site of the NKK Corporation, and then partial modification was implemented for the basic and detailed designs of the plant for the second year running. Furthermore, a review was made so that the results of the element studies that followed the designing of the details would be embodied, and the changes were reflected on orders placed for equipment and construction work. These processes culminated in the 2.4T/day-capable research plant, now complete and subjected to inspections by the relevant Government offices. In a study of the operation of the plant, an operating procedure is worked out, and water-handling tests are conducted for each of the stages of operation. The plant will be subjected to a full test operation, improved as required, studied for proper operation, and will undergo additional construction work as required, all these in preparation for a continuous operation in the future. (NEDO)

Achievement report for fiscal 1981 on Sunshine Part 2. Program-assisted project. Research and development of coal liquefaction technology (Development of direct coal hydroliquefaction plant; development of 2.4T/day-capable research plant); 1981 nendo sekitan ekika gijutsu no kenkyu kaihatsu / chokusetsu suiten ekika plant no kaihatsu seika hokokusho. 2. 2.4t/nichi jikken plant no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

For the goal of developing a direct coal hydroliquefaction plant, designing of a 2.4T/day-capable research plant is conducted as in the preceding fiscal year, devices are purchased and manufactured, and construction work is carried out. The construction work is now over, and the plant is subjected to various inspections by the relevant Government offices. Preparatory tasks are discharged for the study of operation. The material of the 2.4T/day-capable research plant presented here is a compilation of charts of the piping routes, charts of civil engineering and construction, charts of instrumentation, charts of electrical systems, documents of approvals and licenses, etc. (NEDO)

Achievement report for fiscal 1981 on the development of solar energy technologies for the development of practical application technologies for photovoltaic power systems. Experimental fabrication of solar cell panels and verification thereof (Development of technologies for panel assembly process); 1981 nendo taiyo energy gijutsu kenkyu kaihatsu seika hokokusho (taiyoko hatsuden system jitsuyoka gijutsu kaihatsu). Taiyo denchi panel jikken seisaku kensho (panel kumitate kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

In a study of cell array connection process, continuous and automatic connection of cells is named as the basic concept in view of low cost and high reliability. In the designing of details of cell strings, CZ (Czochralski) cell dimensions are reviewed for cell packaging efficiency improvement, interconnectors and wiring are examined for a easier packaging process, and solder connection is thought over for utility cost reduction. Conditions are established for string fabrication process details. In the study of the panel packaging process, panel package designing is carried out and a dedicated mechanical device is installed. In the study of the inspection process and plant system, data are collected, necessary for the construction and adjustment of an inspection device. Research is conducted on the layout of plant facilities, on required utilities, and on facilities operating state signals to be transmitted to the central control unit. As for an inspection jig supply system, transfer system, and storage rack, they are designed, built, and installed. The plant house is now complete. (NEDO)

Achievement report for fiscal 1981 on New Energy and Industrial Technology Development Organization-entrusted projects. Solar energy technology research and development; solar panel experiment, manufacture, and verification (Photovoltaic power system practical application technology; ribbon-type crystal substrate process technology); 1981 nendo taiyo energy gijutsu kenkyu kaihatsu seika hokokusho (taiyoko hatsuden system jitsuyoka gijutsu kaihatsu). Taiyo denchi panel jikken seisaku kensho (ribon kessho kiban kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Carried over from the preceding fiscal year are the development of ribbon crystal pulling technology and the studies of ribbon crystal substrate quality and plant operation. In the development of ribbon crystal pulling process, a pulling drive is built and the limiter mechanism is strengthened for improvement on ribbon crystal flatness, technologies are established for high-speed pulling of broad ribbon crystals, pulling system prototype is built, after-annealing technique is improved for eliminating distortion, and technologies are developed for continuous feeding of raw materials. In the quality examination of ribbon crystal substrates, a method is tested and studied for bringing about a decrease in the number of SiC grains. The object of the plant operation study is a plant capable of producing 250kW-equivalent ribbon crystals a year, and the efforts involve the ribbon pulling system, rough cutter, real-size cutter, etching unit, shape checker, packing, devices for production lines such as warehouses for products, electric power, gas, water, peripheral equipment for waste water treatment etc., ribbon specifications check, quality related assistance equipment to deal with unacceptable products etc., pollution-preventing facilities for the preservation of production environments, and plant buildings. (NEDO)

Report on the achievements in research and development of a coal liquefaction technology in the Sunshine Project in fiscal 1981. Development of a solvolysis liquefaction plant (development of a 1 t/d experimental plant and research on solvolysis liquefaction process); Sekitan ekika gijutsu no kenkyu kaihatsu, solvolysis ekika plant no kaihatsu seika hokokusho. 1t/nichi jikken plant no kaihatsu (solvolysis ekika process no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This paper describes the achievements in the Sunshine Project in fiscal 1981 in development of a solvolysis liquefaction plant. The solvolysis process is characterized by performing the first stage reaction (liquefaction) in a short time by using hydrogenated heavy solvent produced spontaneously in the process. This short-time liquefaction reaction was carried out continuously by using a 1-t/d experimental plant, and a prospect was obtained on smooth operation and realization of the device. A test using a testing device allowing the temperature to rise within several minutes was performed on the effectiveness of a hydrogenated coal based heavy solvent (fractions of a hydrogenated heavy anthracene as a model) as a study on the first stage reaction. Partially hydrogenated materials of polycyclic condensed aromatics in the heavy solvent is largely involved in the initial reaction. In the solid-liquid separation, solids and heavy fractions are selected and removed from the first stage reaction products, and the light fraction is supplied into the second stage reaction (hydrogenation). The solvent deliming process was tested by using a batch type solid-liquid separator, whose effectiveness was verified. Studies were performed by using Australian sub-bituminous coal on operation of a continuous operation device consisted of systems for the first stage reaction (liquefaction), solid-liquid separation, second stage reaction (hydrogenation), and solvent circulation. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. First year report. Commercialization of depth dechlorination/debromination refining catalyst of waste plastic derived oil and the liquefaction process; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium kenkyu kaihatsu bun'ya. Hai plastic bunkaiyu no shindo datsuenso dasshuso seisei shokubai oyobi yuka process no jitsuyoka (dai 1 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The development was proceeded with of technology to produce iron oxide/porous carbon composite catalyst which promotes dehalogenation of thermal-degraded oil at low cost and in large quantity. This catalyst enables the improvement in operability and safety in the liquefaction process for mixed plastic and in quality of oil product. The development is also made of a regional distributed small batch liquefaction system with processing ability of 1t/day. Studies were made in the following 6 fields: 1) analysis of the dehalogenation performance of catalyst and the evaluation; 2) development of a method to industrially produce halogen compound refining catalyst; 3) R and D of a method to analyze environmental components; 4) evaluation study of halogen resistant materials and halogen resistant technology; 5) development of a small test device for commercialization of the liquefaction/degradation process; 6) comprehensive investigational study. In 1), the performance of prototype catalyst was confirmed, and the structure was analyzed. Also developed was iron chloride/SiO{sub 2} catalyst which converts organic halogen to inorganic halogen. (NEDO)

Fiscal 1997 report on the R and D project consignment from NEDO on industrial science and technology. R and D on total base technology for marine resources (Mn nodules mining system) (total system (experimental plan)); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (mangan dankai saiko system) seika hokokusho (total system (jikken keikaku) hen)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Study was made on the design of experiments for confirming the technological and economical feasibility of commercial production of Mn nodules. An experimental sea area was selected considering Mn nodule characteristics such as concentration, continuity of nodule distribution and nodule size, and sea bottom topographic features such as flatness and exposed bed rock disturbing traveling of nodule collectors. The experimental plan was decided on the basis of the survey and study on an experimental scale, various requirements, weather and sea weather features of the sea area, and sea bottom conditions. Based on the experimental plan, various verification tests and simulation analyses were carried out, and functions of various equipment were confirmed. The conceptual design of a mining system assumed both pump-lift and air-lift systems, and yearly production rates of 2 and 3 million tons by 2 mining barges, and summarized main points of every system. As the evaluation result, the future direction of commercial production of Mn nodules was clarified to a certain extent. 5 figs., 21 tabs.

Report on the achievements in research and development of a coal liquefaction technology in the Sunshine Project in fiscal 1981. Development of a solvent extraction and liquefaction plant (development of a 1-t/d experimental plant and research on the solvent extraction and liquefaction process); 1981 nendo sekitan ekika gijutsu no kenkyu kaihatsu, yozai chushutsu ekika plant no kaihatsu seika hokokusho. 1t/d jikken plant no kaihatsu (yozai chushutsu ekika process no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Among the items of the solvent extraction and liquefaction plant technologies in the Sunshine Project in fiscal 1981, this paper describes the achievements in developing a 1-t/d experimental plant and the solvent extraction and liquefaction process. Basic facilities were completed by giving expansion constructions on the extraction reaction column, gas-liquid separation column, and hydrogenation reaction column. The operation was performed with the primary object placed on verifying the effect of measures on problems that have been extracted, and checking the solvent balance. The conversion rate at an extraction reaction temperature of 450 degrees C was 83%, agreeing with the result of the fundamental study. The solvent has turned light as a result of 153-hour continuous operation, but circulating use was possible. Progress of the reaction has become easily controllable in the hydrogenation system. Fundamental discussions were given on engineering aspects, which require further accumulation of data. In the research of the solvent extraction and liquefaction process, fiscal 1981 has performed discussions on liquefaction catalysts, and on the effect of the hydrogen donating solvents. The discussions were for the fundamental research to establish adequate conditions for the 1-t/d experimental plant by operating a small continuous operation facility to its full extent, and by using a batch type reaction device. Screening was also carried out on catalysts. (NEDO)